The consequences from liquid pathways after a reactor meltdown accident

International Nuclear Information System (INIS)

Niemczyk, S.J.; Adams, K.G.; Murfin, W.B.; Ritchie, L.T.; Eppel, E.W.; Johnson, J.D.

1981-06-01

The potential radiological impact of a core-melt accident on the human population has been investigated. In particular, the radiation dose received from radioactivity which could reach the population via liquid pathways has been considered. Radioactivity could be released directly to the hydrosphere after a core-melt accident as a result of melt-through of the containment basemat followed by any of three processes: (1) leaching of the melt debris; 2 escape of sumpwater through the hole formed by the melt (or from passage out of the containment by an alternate route); and 3) depressurization of the containment atmosphere through the melt hole. The three types of releases would differ primarily in their rates, their magnitudes and their radioactive compositions. Both the containment atmosphere and the sumpwater releases would occur relatively rapidly. However, most of the radionuclides present in these two releases in substantial quantities would be expected to be rather short-lived. Therefore, such releases could have a significant impact at a specific site only if the travel times of the important radionuclides to the human population were small. In contrast, leaching of radionuclides from the melt debris would be expected to occur relatively slowly. Most of the long-lived isotopes would be expected to be found primarily in the melt debris. Consequently, even though this release occurred relatively slowly, the impact could still be significant. In contrast to the situation for releases to the atmosphere, accidents corresponding to the most probable RSS (Reactor Safety Study) meltdown categories would result in the largest releases to the hydrosphere. Furthermore, substantial amounts of radioactivity would generally be expected to be released to the hydrosphere during any meltdown accident involving complete melt-through of the containment basemat. On the basis of subsurface hydrologies alone, sites range from those that essentially preclude any impacts to the human

Neutronics and thermohydraulics of the reactor C.E.N.E. Part II

International Nuclear Information System (INIS)

Caro, R.

1976-01-01

In this report the analysis of neutronics thermohydraulics and shielding of the 10 HWt swimming pool reactor C.E.N.E is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs

Neutronics and thermohydraulics of the reactor C.E.N.E.-Part I

International Nuclear Information System (INIS)

Caro, R.; Ahnert, C.; Naudin, A. E.; Martinez Fanegas, R.; Minguez, E.; Rovira, A.

1976-01-01

In this report the analysis of neutronics (both statics and kinetics), of the 10 MWt swimming pool reactor C.E.N.E, is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking, carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs

Serious accidents of PWR type reactors for power generation

International Nuclear Information System (INIS)

2008-12-01

This document presents the great lines of current knowledge on serious accidents relative to PWR type reactors. First, is exposed the physics of PWR type reactor core meltdown and the possible failure modes of the containment building in such a case. Then, are presented the dispositions implemented with regards to such accidents in France, particularly the pragmatic approach that prevails for the already built reactors. Then, the document tackles the case of the European pressurized reactor (E.P.R.), for which the dimensioning takes into account explicitly serious accidents: it is a question of objectives conception and their respect must be the object of a strict demonstration, by taking into account uncertainties. (N.C.)

The consequences from liquid pathways after a reactor meltdown accident

Energy Technology Data Exchange (ETDEWEB)

Niemczyk, S J; Adams, K G; Murfin, W B; Ritchie, L T; Eppel, E W; Johnson, J D

1981-06-01

The potential radiological impact of a core-melt accident on the human population has been investigated. In particular, the radiation dose received from radioactivity which could reach the population via liquid pathways has been considered. Radioactivity could be released directly to the hydrosphere after a core-melt accident as a result of melt-through of the containment basemat followed by any of three processes: (1) leaching of the melt debris; 2 escape of sumpwater through the hole formed by the melt (or from passage out of the containment by an alternate route); and 3) depressurization of the containment atmosphere through the melt hole. The three types of releases would differ primarily in their rates, their magnitudes and their radioactive compositions. Both the containment atmosphere and the sumpwater releases would occur relatively rapidly. However, most of the radionuclides present in these two releases in substantial quantities would be expected to be rather short-lived. Therefore, such releases could have a significant impact at a specific site only if the travel times of the important radionuclides to the human population were small. In contrast, leaching of radionuclides from the melt debris would be expected to occur relatively slowly. Most of the long-lived isotopes would be expected to be found primarily in the melt debris. Consequently, even though this release occurred relatively slowly, the impact could still be significant. In contrast to the situation for releases to the atmosphere, accidents corresponding to the most probable RSS (Reactor Safety Study) meltdown categories would result in the largest releases to the hydrosphere. Furthermore, substantial amounts of radioactivity would generally be expected to be released to the hydrosphere during any meltdown accident involving complete melt-through of the containment basemat. On the basis of subsurface hydrologies alone, sites range from those that essentially preclude any impacts to the human

Analyses of containment loading by hydrogen burning during hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Bracht, K.; Tiltmann, M.

1983-01-01

The possibility of occurance of violent hydrogen burning during a LWR meltdown accident and its consequences to containment atmosphere conditions are discussed. Two accident sequences with low and high system pressure during the in-vessel-melt phase of a meltdown accident are considered. In both sequences only deflagration, but no detonation may become possible, presuming homogeneity of the containment atmospheres. In a low pressure szenario the pressure increase due to deflagration will not reach the failure pressure of the containment, if combustion takes place when the flammability limit is reached. For the special situation of a rapid release of steam and hydrogen after a high-pressure failure of a reactor pressure vessel, calculations with a multicompartment code show that the possibility for hydrogen burning does not exist. Thus, an additional augmentation of the steam spike as a consequence of the failure of the pressure vessel cannot occur. (orig.)

Release of fission products during controlled loss-of-coolant accidents and hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Albrecht, H.; Malinauskas, A.P.

1978-01-01

A few years ago the Projekt Nukleare Sicherheit joined the United States Nuclear Regulatory Commission in the development of a research program which was designed to investigate fission product release from light water reactor fuel under conditions ranging from spent fuel shipping cask accidents to core meltdown accidents. Three laboratories have been involved in this cooperative effort. At Argonne National Laboratory (ANL), the research effort has focused on noble gas fission product release, whereas at Oak Ridge National Laboratory (ORNL) and at Kernforschungszentrum Karlsruhe (KfK), the studies have emphasized the release of species other than the noble gases. In addition, the ORNL program has been directed toward the development of fission product source terms applicable to analyses of spent fuel shipping cask accidents and controlled loss-of-coolant accidents, and the KfK program has been aimed at providing similar source terms which are characteristic of core meltdown accidents. The ORNL results are presented for fission product release from defected fuel rods into a steam atmosphere over the temperature range 500 to 1200 0 C, and the KfK results for release during core meltdown sequences

Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

International Nuclear Information System (INIS)

Ginsberg, T.; Chen, J.C.

1984-01-01

Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

Safety analysis of a stratified reactor foundation subject to core meltdown

International Nuclear Information System (INIS)

Laermann, K.H.; Berhalter, D.; Wieching, G.

1983-01-01

Comprehensive calculations were made to examine a foundation plate under static load with non-linear material behaviour. In particular, deformation and crack behaviour of the plate were observed. The calculations hereunder, made to calculate the time of rupture of the plate with the foundation exposed to high temperatures, with and without cavity formation, prove that high temperatures are not as relevant as the melt-down of the layers of armour on top of the middle of the plate. The consequences of this survey are: to protect the top armour of the plate centre and not to use it as support for any structural components. This free space could then be used to instal said multi-layer plate. (orig./HP) [de

Method of reducing the hazard which may occur as a consequence of a reactor core meltdown

International Nuclear Information System (INIS)

Donne, M.D.; Dorner, S.; Schumacher, G.

1978-01-01

The core melt resulting from a meltdown accident of a GFB, LWR or LMFRR is collected by a core catcher from graphite placed below the core. The core melt is penetrating step by step into a borate store in the collecting vessel and is dissolving in it. Therefore the borate at the same time will absorb the decay heat. In order to remove the solidified and cooled down melted mass water is applied eliminating the borate. The remaining oxide state of the powdery core is sucked off again from the core catcher together with the water. The borate store (e.g. alkali borate) itself consists of separate layers with shaped parts, the coverings of which are made of steel, iron, cast iron, nickel, iron or nickel alloys, ceramic material or glass. (DG) [de

Method of reducing the hazard which may occur as a consequence of a reactor core meltdown

International Nuclear Information System (INIS)

Donne, M.D.; Dorner, S.; Schumacher, G.

1985-01-01

The core melt resulting from a meltdown accident of a GFB, LWR or LMFRR is collected by a core catcher from graphite placed below the core. The core melt is penetrating step by step into a borate store in the collecting vessel and is dissolving in it. Therefore the borate at the same time will absorb the decay heat. In order to remove the solidified and cooled down melted mass water is applied eliminating the borate. The remaining oxide states of the powdery core is sucked off again from the core catcher together with the water. The borate store (e.g. alkali borate) itself consists of separate layers with shaped parts, the coverings of which are made of steel, iron, cast iron, nickel, iron or nickel alloys, ceramic material or glass. (orig./PW)

Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

International Nuclear Information System (INIS)

Ginsberg, T.; Chen, J.C.

1984-01-01

Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench (removal of stored energy from initial temperature to saturation temperature) of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

Sterilization of E. coli bacterium in a flowing N2-O2 post-discharge reactor

International Nuclear Information System (INIS)

Villeger, S; Cousty, S; Ricard, A; Sixou, M

2003-01-01

Effective destruction of Escherichia coli (E. coli) bacteria has been obtained in a flowing N 2 -O 2 microwave post-discharge reactor. The sterilizing agents are the O atoms and the UV emissions of NOβ which are produced by N and O atoms recombination in the reactor. In the following plasma conditions: pressure 5 Torr, flow rate 1 L n min -1 , microwave power of 100 W in a quartz tube of 5 mm, an O atom density of 2.5x10 15 cm -3 is measured by NO titration in the post-discharge reactor with UV emission in a N 2 -(5%)O 2 gas mixture. Full destruction of 10 13 cfu ml -1 E. coli is observed after a treatment time of 25 min. (rapid communication)

Anticipated transients without scram for light water reactors: implications for liquid metal fast breeder reactors

International Nuclear Information System (INIS)

Kastenberg, W.E.; Solomon, K.A.

1979-07-01

In the design of light water reactors (LWRs), protection against anticipated transients (e.g., loss of normal electric power and control rod withdrawal) is provided by a highly reliable scram, or shutdown system. If this system should become inoperable, however, the transient could lead to a core meltdown. The Nuclar Regulatory Commission (NRC) has proposed, in NUREG-0460 [1], new requirements (or acceptance criteria) for anticipated transients without scram (ATWS) events and the manner in which they could be considered in the design and safety evaluation of LWRs. This note assesses the potential impact of the proposed LWR-ATWS criteria on the liquid metal fast breeder reactor (LMFBR) safety program as represented by the Clinch River Breeder Reactor Plant

Detonability of containment building atmospheres during core-meltdown accidents

International Nuclear Information System (INIS)

Jaung, R.; Berlad, L.; Pratt, W.

1983-01-01

During Core-Meltdown Accidents in Light Water Reactors, significant quantities of combustible gases could be released to the containment building. The highest possible peak pressure fields that may occur through combustion processes are associated with detonation phenomena. Accordingly, it is necessary to understand and identify the possible ways in which detonations may or may not occur. Although no comprehensive theory of detonation is currently available, there are useful guidelines, which can be derived from current theoretical concepts and the body of experimental data. This paper examines these guidelines and indicates how they may be used to evaluate the possible occurrence of detonation-related combustion processes. In particular, this study identifies three features that an initiation source must achieve if it is to ultimately result in a stable detonation. One of these features requires post-shock initial conditions that lead to very short ignition delays. This concept is used to examine the possibility of achieving quasi-steady detonation phenomena in nuclear reactor containment buildings during postulated core-melt accidents

Reactors at sea

International Nuclear Information System (INIS)

Hines, Colin

1988-01-01

The Greenpeace Nuclear Free Seas Campaign is outlined. The campaign aims to bring the environmental hazards from nuclear submarines and naval ships carrying nuclear weapons to public attention. Worldwide there are 544 nuclear reactor ships or submarines each with the potential to meltdown with serious environmental consequences. One meltdown is known to have occurred. Five reactors have been abandoned on the sea bed. Nuclear powered submarines are based at Rosyth, Faslane, Holy Loch, Plymouth and Portsmouth and routinely come into and out of those harbours. There have also been accidents involving nuclear weapons on board submarines, aircraft carriers or destroyers which carry nuclear depth bombs and free fall bombs. The Royal Navy's accident emergency plans for nuclear naval bases are inadequate. There is a threat to the environment when the reactors are decommissioned. There are no clear plans as to how to deal with the decommissioning of the submarines or ships although the fuel rods have been removed from the first British nuclear submarine, Dreadnought. (U.K.)

Oxidation during reflood of reactor core with melting cladding

Energy Technology Data Exchange (ETDEWEB)

Siefken, L.J.; Allison, C.M.; Davis, K.L. [and others

1995-09-01

Models were recently developed and incorporated into the SCDAP/RELAP5 code for calculating the oxidation of fuel rods during cladding meltdown and reflood. Experiments have shown that a period of intense oxidation may occur when a hot partially oxidized reactor core is reflooded. This paper offers an explanation of the cladding meltdown and oxidation processes that cause this intense period of oxidation. Models for the cladding meltdown and oxidation processes are developed. The models are assessed by simulating a severe fuel damage experiment that involved reflood. The models for cladding meltdown and oxidation were found to improve calculation of the temperature and oxidation of fuel rods during the period in which hot fuel rods are reflooded.

Eigen's Error Threshold and Mutational Meltdown in a Quasispecies Model

OpenAIRE

Bagnoli, F.; Bezzi, M.

1998-01-01

We introduce a toy model for interacting populations connected by mutations and limited by a shared resource. We study the presence of Eigen's error threshold and mutational meltdown. The phase diagram of the system shows that the extinction of the whole population due to mutational meltdown can occur well before an eventual error threshold transition.

Synthesis of the IRSN report on the topic of water way answers to implement in case of accident with core meltdown occurring on operating pressurized water nuclear reactors

International Nuclear Information System (INIS)

2009-06-01

This report briefly discusses the efficiency of technical measures adopted for the implementation of water ways as answers to an accident with core meltdown in operating pressurized water nuclear reactors. While mentioning the importance of the hydro-geological characteristics of the various sites, the IRSN asks EDF to plan and implement means to prevent any rejection through water ways for some of these sites, to investigate the possibility of building a geotechnical enclosure, to define a storing-control-treatment-rejection chain which would guarantee an efficient management of the water to be pumped, to study retention phenomena for strontium and caesium isotopes in sands and gravels

Nuclear reactor core catcher

International Nuclear Information System (INIS)

1977-01-01

A nuclear reactor core catcher is described for containing debris resulting from an accident causing core meltdown and which incorporates a method of cooling the debris by the circulation of a liquid coolant. (U.K.)

Mutational meltdown in laboratory yeast populations

NARCIS (Netherlands)

Zeyl, C.; Mizesko, M.; Visser, de J.A.G.M.

2001-01-01

In small or repeatedly bottlenecked populations, mutations are expected to accumulate by genetic drift, causing fitness declines. In mutational meltdown models, such fitness declines further reduce population size, thus accelerating additional mutation accumulation and leading to extinction. Because

GLOBAL ECONOMIC MELTDOWN AND THE NIGERIAN ...

African Journals Online (AJOL)

global financial meltdown, marked by the collapse of hitherto revered and great financial ... Indeed it is an integral part of a market (capitalist) economy. .... competitively in economic production, so also is the deficit in its trade with the rest of the.

Concepts for passive heat removal and filtration systems under core meltdown conditions

International Nuclear Information System (INIS)

Wilhelm, J.G.; Neitzel, H.-J.

1993-01-01

The objective of the new containment concept being developed by KfK is the complete passive enclosure of a power reactor after a core meltdown accident by means of a solid containment structure and passive removal of the decay heat. This is to be accomplished by cooling the containment walls with ambient air, with thermoconvection as the driving force. The concept of the containment is described. Data are given of the heat removal and the requirements for filtration of the exhaust air, which is contaminated due to the leak rate assumed for the inner containment. The concept for the filter system is described. Various solutions for reduction of the large volumetric flow to be filtered are discussed. 3 refs., 8 figs

A critical experimental study of integral physics parameters in simulated LMFBR meltdown cores

International Nuclear Information System (INIS)

Bhattacharyya, S.K.; Wade, D.C.; Bucher, R.G.; Smith, D.M.; McKnight, R.D.; Lesage, L.G.

1978-01-01

Integral physics parameters of several representative, idealized meltdown LMFBR configurations were measured in mockup critical assemblies on the ZPR-9 reactor at Argonne National Laboratory. The experiments were designed to provide data for the validation of analytical methods used in the neutronics part of LMFBR accident analysis. Large core distortions were introduced in these experiments (involving 18.5% core volume) and the reactivity worths of configuration changes were determined. The neutronics parameters measured in the various configurations showed large changes upon core distortion. Both diffusion theory and transport theory methods were shown to mispredict the experimental configuration eigenvalues. In addition, diffusion theory methods were shown to result in a non-conservative misprediction of the experimental configuration change worths. (author)

Steam explosion - physical foundations and relation to nuclear reactor safety

International Nuclear Information System (INIS)

Schumann, U.

1982-08-01

'Steam explosion' means the sudden evaporation of a fluid by heat exchange with a hotter material. Other terms are 'vapour explosion', 'thermal explosion', and 'energetic fuel-coolant interaction (FCI)'. In such an event a large fraction of the thermal energy initially stored in the hot material may possibly be converted into mechanical work. For pressurized water reactors one discusses (e.g. in risk analysis studies) a core melt-down accident during which molten fuel comes into contact with water. In the analysis of the consequences one has to investigate steam explosions. In this report an overview over the state of the knowledge is given. The overview is based on an extensive literature review. The objective of the report is to provide the basic knowledge which is required for understanding of the most important theories on the process of steam explosions. Following topics are treated: overview on steam explosion incidents, work potential, spontaneous nucleation, concept of detonation, results of some typical experiments, hydrodynamic fragmentation of drops, bubbles and jets, coarse mixtures, film-boiling, scenario of a core melt-down accident with possible steam-explosion in a pressurized water reactor. (orig.) [de

Effects of methodic deficiencies on the quantification of core meltdown frequency

International Nuclear Information System (INIS)

Hahn, L.

1984-01-01

The application of sequence of events and fault tree analyses for the assessment of the core meltdown frequency raises problems, most of which can be classified under: - Completeness and representativeness of sequences and cuases of events - Modelling of conditional outages (common-mode outages) - Modelling of human behaviour - Reliability data and models. All of the weak points of the German Risk Study related to these problems which are mentioned by the Ecological Institute show a tendency to underestimate the core meltdown frequency by a factor at least 6. (RF) [de

Nuclear reactor core safety device

International Nuclear Information System (INIS)

Colgate, S.A.

1977-01-01

The danger of a steam explosion from a nuclear reactor core melt-down can be greatly reduced by adding a gasifying agent to the fuel that releases a large amount of gas at a predetermined pre-melt-down temperature that ruptures the bottom end of the fuel rod and blows the finely divided fuel into a residual coolant bath at the bottom of the reactor. This residual bath should be equipped with a secondary cooling loop

Reactor safety study. An assessment of accident risks in U.S. commercial nuclear power plants. Appendices VII, VIII, IX, and X

International Nuclear Information System (INIS)

1975-10-01

Information is presented concerning the release of radioactivity in reactor accidents; physical processes in reactor meltdown accidents; safety design rationale for nuclear power plants; and design adequacy

Chernobyl: recovery operations and the entombment of Reactor 4

International Nuclear Information System (INIS)

Dalziel, S.P.C.

1988-01-01

The immediate actions taken following the accident at the Chernobyl-number 4 reactor in April 1986 are described. These included actions to put out the fires, initial medical aid and the dropping of sand, lead, dolomite and boron onto the reactor from helicopters. Following this the chamber below the damaged reactor core was filled with concrete to prevent any further explosions or meltdown. The reactor was subsequently entombed in steel and concrete. The evacuation of the surrounding area is also mentioned. (U.K.)

The Chernobyl reactor accident. Pt. 1 and 2

International Nuclear Information System (INIS)

1986-06-01

The report first summarizes the available information on the various incidents of the whole accident scenario, and combines the information to present a first general outline and a basis for appraisal. The most significant incidents reported, namely power excursion, core meltdown, and fire, are discussed with a view to the reactor design and safety of reactors installed in the FRG. The main differences and advantages of German reactor designs are shown, as e.g.: Power excursions are mastered by inherent physical conditions; far better redundancy of engineered safety systems; enclosure of the complete reactor cooling system in a pressure-retaining steel containment; reactor buildings being made of reinforced concrete. The second part of the report deals with the radiological effects to be expected for our country. Data are given on the varying radiological exposure of the different regions. The fate and uptake of radioactivity in the human body are discussed. The conclusion drawn from the data presented is that the individual exposure due to the reactor accident will remain within the variations and limits of natural radioactivity and effects. (orig./HP) [de

The nature of reactor accidents

International Nuclear Information System (INIS)

Domaratzki, Z.; Campbell, F.R.; Atchison, R.J.

1981-01-01

Reactor accidents are events which result in the release of radioactive material from a nuclear power plant due to the failure of one or more critical components of that plant. The failures, depending on their number and type, can result in releases whose consequences range from negligible to catastrophic. By way of examples, this paper describes four specific accidents which cover this range of consequence: failure of a reactor control system, loss of coolant, loss of coolant with impaired containment, and reactor core meltdown. For each a possible sequence of events and an estimate of the expected frequency are presented

Reactor safety study. An assessment of accident risks in U. S. commercial nuclear power plants. Appendices VII, VIII, IX, and X. [PWR and BWR

Energy Technology Data Exchange (ETDEWEB)

1975-10-01

Information is presented concerning the release of radioactivity in reactor accidents; physical processes in reactor meltdown accidents; safety design rationale for nuclear power plants; and design adequacy.

Evaluation of Effect of Global Economic Meltdown on Capital Market Performance

Directory of Open Access Journals (Sweden)

ONAOLAPO ADEKUNLE RAHMAN

2013-07-01

Full Text Available The recent financial crisis that loomed the global economy was considered more inclusive than any other period of financial turmoil in the past 60 years. This paper evaluates the implications of the global economic meltdown on the Nigerian Capital Market Performance using the market capitalization of the Nigerian Stock Exchange as a major indicator. When the global economic meltdown came, it poses a recession on the Market Capitalization and the volume of share index of the Nation. This study depends entirely on secondary data in form of annual aggregate time series data of Market capitalization (dependent variable, exchange rate, interest rate, inflation rate, market share index with Dummy variable to represent the period of economic crisis. Ordinary least square of multiple regressions was used to analyze the data into econometric model while F-statistics was used to test for the formulated hypothesis. This study depicts that the global economic meltdown has a negative effect on the Capital Market Performance. It was therefore recommended that the Federal government and the regulatory agencies (CBN, NSE, SEC etc. should come up with intervention and fiscal policies that will suppress these effects and jumpstart the capital market and that the policies should be properly implemented and monitored.

Thermal and stress analyses of meltdown cups for LMFBR safety experiments using SLSF in-reactor loops

Energy Technology Data Exchange (ETDEWEB)

Blomquist, C. A. [Argonne National Lab., IL (United States); Ariman, T. [Univ. of Notre Dame, IN (United States); Pierce, R. D.; Pedersen, D. R. [Argonne National Lab., IL (United States)

1977-07-01

The test trains for the Sodium Loop Safety Facility (SLSF) in-reactor experiments, which simulate hypothetical LMFBR accidents, have a meltdown cup to protect the primary containment from the effects of molten materials. Thermal and stress analyses were performed on the cup which is designed to contain 3.6 kg of molten fuel and 2.4 kg of molten steel. The cup principal components are: 1. A 38 mm diameter tungsten spike which provides initial fuel quenching and prevents fuel boiling, 2. A 73 mm inside diameter tungsten liner to isolate the support vessel from the molten material high initial temperature, 3. An insulator which is an expedient for extending the experiment time, and 4. An Inconel 625 vessel which provides the structural support to withstand the thermal and pressure stresses. The spike, liner, and insulator are supported by a hemispherical tungsten end cap which fits inside the hemispherical bottom of the support vessel. This vessel is attached to the 316 stainless steel test train with an Inconel 750 wire-formed retaining ring. Thermal analyses were performed with the Argonne-modified version of the general heat transfer code THTB, based on the instantaneous addition of 3200/sup 0/K molten fuel with a decay heat of 9 W/gm and 1920/sup 0/K molten steel. These analyses have shown that the cup will adequately cool the molten materials. The maximum temperature occurs at the center of the fuel region but it is always less than the fuel boiling point. The maximum temperature occurs at the center of the fuel region but it is always less than the fuel boiling point. The most severe heating occurs when there is no sodium flow outside the cup. For this case the sodium boils (approximately 1200/sup 0/K) and the Inconel vessel and tungsten liner temperatures are approximately 1250/sup 0/K and 2420/sup 0/K, respectively.

Pressure tube type reactors

International Nuclear Information System (INIS)

Komada, Masaoki.

1981-01-01

Purpose: To increase the safety of pressure tube type reactors by providing an additional ECCS system to an ordinary ECCS system and injecting heavy water in the reactor core tank into pressure tubes upon fractures of the tubes. Constitution: Upon fractures of pressure tubes, reduction of the pressure in the fractured tubes to the atmospheric pressure in confirmed and the electromagnetic valve is operated to completely isolate the pressure tubes from the fractured portion. Then, the heavy water in the reactor core tank flows into and spontaneously recycles through the pressure tubes to cool the fuels in the tube to prevent their meltdown. By additionally providing the separate ECCS system to the ordinary ECCS system, fuels can be cooled upon loss of coolant accidents to improve the safety of the reactors. (Moriyama, K.)

IRSN research programs concerning reactor safety

International Nuclear Information System (INIS)

Bardelay, J.

2005-01-01

This paper is made up of 3 parts. The first part briefly presents the missions of IRSN (French research institute on nuclear safety), the second part reviews the research works currently led by IRSN in the following fields : -) the assessment of safety computer codes, -) thermohydraulics, -) reactor ageing, -) reactivity accidents, -) loss of coolant, -) reactor pool dewatering, -) core meltdown, -) vapor explosion, and -) fission product release. In the third part, IRSN is shown to give a major importance to experimental programs led on research or test reactors for collecting valid data because of the complexity of the physical processes that are involved. IRSN plans to develop a research program concerning the safety of high or very high temperature reactors. (A.C.)

Core catcher for nuclear reactor core meltdown containment

International Nuclear Information System (INIS)

Driscoll, M.J.; Bowman, F.L.

1978-01-01

A bed of graphite particles is placed beneath a nuclear reactor core outside the pressure vessel but within the containment building to catch the core debris in the event of failure of the emergency core cooling system. Spray cooling of the debris and graphite particles together with draining and flooding of coolant fluid of the graphite bed is provided to prevent debris slump-through to the bottom of the bed

N Reactor pressure tube 2566 postirradiation examination

International Nuclear Information System (INIS)

Scott, K.V.

1978-01-01

Pressure tube 2566 was removed from N Reactor in July, 1977 to initiate the postirradiation examination program required by the Technical Specifications. Destructive examination of the pressure tube, after a maximum accumulated fluence of 4.6 x 10 21 n/cm 2 (E > 1 MeV), was conducted at the Hanford Engineering Development Laboratory to determine the effects of reactor service on the mechanical properties and hydrogen absorption and corrosion characteristics of the pressure tube. Tube 2566 is the sixth tube removed for destructive examination since the initial reactor startup. Evaluation of test results reveal that no significant detrimental changes have occurred in the parameters studied, since the last tube was removed in 1974

Heat dissipating nuclear reactor

Science.gov (United States)

Hunsbedt, A.; Lazarus, J.D.

1985-11-21

Disclosed is a nuclear reactor containment adapted to retain and cool core debris in the unlikely event of a core meltdown and subsequent breach in the reactor vessel. The reactor vessel is seated in a cavity which has a thick metal sidewall that is integral with a thick metal basemat at the bottom of the cavity. The basemat extends beyond the perimeter of the cavity sidewall. Underneath the basemat is a porous bed with water pipes and steam pipes running into it. Water is introduced into the bed and converted into steam which is vented to the atmosphere. A plurality of metal pilings in the form of H-beams extend from the metal base plate downwardly and outwardly into the earth.

List of the reports from reactor safety research of the BMFT and USNRC

International Nuclear Information System (INIS)

1977-02-01

This list presents a survey of reports from the FRG and USA issued on special problems of reactor safety research. The problems include emergency core cooling, the containment during loss of coolant, core meltdown, component safety, external impacts, risk and reliability, quality assurance, fission product transport, radiation exposure, as well as the LWR, HTR and the fast sodium-cooled reactor in general. (orig./HK) [de

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2001-01-01

On August 17, 1998, Russia defaulted on its domestic public debt, declared a moratorium on the private banks foreign liabilities which was equivalent to an outright default, and abandoned its exchange rate regime. The depth of the Russian meltdown shocked the international markets, and precipitated

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2002-01-01

On August 17, 1998, Russia defaulted on its domestic public debt, declared a moratorium on the private banks foreign liabilities which was equivalent to an outright default, and abandoned its exchange rate regime. The depth of the Russian meltdown shocked the international markets, and precipitated

A Primer on Financial System Meltdown. The Economists' View

OpenAIRE

Hahn, Franz R.

2008-01-01

Ideologues are quick to explain the current financial meltdown: it's the markets, stupid. Economists agree but add: it's politics too, stupid. Ideologues agree but counter: first and foremost it's capitalism, stupid. Economists agree but reply: §$%&?!, stupid. This is where this short paper takes us: it makes an attempt to give a brief overview of the economists' views on the ongoing financial system crisis explaining "§$%&?!, stupid".

European community light water reactor safety research projects. Experimental issue

International Nuclear Information System (INIS)

1975-01-01

Research programs on light water reactor safety currently carried out in the European Community are presented. They cover: accident conditions (LOCA, ECCS, core meltdown, external influences, etc...), fault and accident prevention and means of mitigation, normal operation conditions, on and off site implications and equipment under severe accident conditions, and miscellaneous subjects

Lessons from the Russian meltdown : the economics of soft legal constraints

NARCIS (Netherlands)

Perotti, E.C.

2002-01-01

On 17 August 1998 Russia abandoned its exchange rate regime, defaulted on its domestic public debt and declared a moratorium on banks' foreign liabilities. This was equivalent to an outright default. The depth and speed of the Russian meltdown shocked the international markets and precipitated a

A status report on the integral fast reactor fuels and safety program

International Nuclear Information System (INIS)

Pedersen, D.R.; Seidel, B.R.

1990-01-01

The integral fast reactor (IFR) is an advanced liquid-metal-cooled reactor (ALMR) concept being developed at Argonne National Laboratory. The IFR program is specifically responsible for the irradiation performance, advanced core design, safety analysis, and development of the fuel cycle for the US Department of Energy's ALMR program. The basic elements of the IFR concept are (a) metallic fuel, (b) liquid-sodium cooling, (c) modular, pool-type reactor configuration, (d) an integral fuel cycle based upon pyrometallurgical processing. The most significant safety aspects of the IFR program result from its unique fuel design, a ternary alloy of uranium, plutonium, and zirconium. This fuel is based on experience gained through > 25 yr operation of the Experimental Breeder Reactor II (EBR-II) with a uranium alloy metallic fuel. The ultimate criteria for fuel pin design is the overall integrity at the target burnup. The probability of core meltdown is remote; however, a theoretical possibility of core meltdown remains. The next major step in the IFR development program will be a full-scale pyroprocessing demonstration to be carried out in conjunction with EBR-II. The IFR fuel cycle closure based on pyroprocessing will also have a dramatic impact on waste management options and on actinide recycling

Study of diluting and absorber materials to control the reactivity during a postulated core meltdown accident in generation IV reactors

International Nuclear Information System (INIS)

Plevacova, Kamila

2010-01-01

In order to limit the consequences of a hypothetical core meltdown accident in Generation IV Sodium Fast Reactors, absorber materials in or near the core, such as boron carbide B 4 C, and diluting materials in the core catcher will be used to prevent recriticality within the mixture of molten oxide fuel and molten structures called corium. The aim of the PhD thesis was to select materials of both types and to understand their behaviour during their interaction with corium, from chemical and thermodynamic points of view. Concerning B 4 C, thermodynamic calculations and experiments agree with the formation of two immiscible phases at high temperature in the B 4 C - UO 2 system: one oxide and one boride. This separation of phases can reduce the efficiency of the neutrons absorption inside the molten fuel contained in the oxide phase. Moreover, volatilization of a part of the boron element can occur. According to these results, the necessary quantity of B 4 C to be introduced should be reconsidered for postulated severe accident sequence. Other solution could be the use of Eu 2 O 3 or HfO 2 as absorber material. These oxides form a solid solution with the oxide fuel. Concerning the diluting materials, mixed oxides Al 2 O 3 - HfO 2 and Al 2 O 3 - Eu 2 O 3 were preselected. These systems being completely unknown to date at high temperature in association with UO 2 , first points on the corresponding ternary phase diagrams were researched. Contrary to Al 2 O 3 - Eu 2 O 3 - UO 2 system, the Al 2 O 3 - HfO 2 - UO 2 mixture presents only one eutectic and thus only one solidification path which makes easier forecasting the behaviour of corium in the core catcher. (author)

The acute effects of the thermogenic supplement Meltdown on energy expenditure, fat oxidation, and hemodynamic responses in young, healthy males

Directory of Open Access Journals (Sweden)

Cooke Matt

2008-12-01

Full Text Available Abstract The purpose of this study was to evaluate the effects of a thermogenic supplement, Meltdown, on energy expenditure, fat oxidation, and hemodynamics before and after maximal treadmill exercise. In a double-blind, randomized, placebo-controlled, cross-over design, 12 male participants underwent two testing sessions after consuming either the Meltdown or placebo supplement. While in a fasted state, participants rested for one hour, orally ingested either Meltdown or placebo and rested for another hour, performed a maximal treadmill exercise test, and then rested for another hour. Throughout the testing protocol, resting energy expenditure (REE and respiratory exchange ratio (RER were assessed. In addition, heart rate (HR and blood pressure (BP were assessed before and after exercise. Meltdown increased REE significantly more than placebo at 45 min (1.44 ± 0.25 vs. 1.28 ± 0.23 kcal/min; p = 0.003, 60 min (1.49 ± 0.28 vs. 1.30 ± 0.22 kcal/min; p = 0.025, and 120 min (1.51 ± 0.26 vs. 1.33 ± 0.27 kcals/min; p = 0.014 post-ingestion. Meltdown significantly decreased RER at 30 min (0.84 ± 0.03 vs. 0.91 ± 0.04; p = 0.022 and 45 min post-ingestion (0.82 ± 0.04 vs. 0.89 ± 0.05; p = 0.042, and immediately post-exercise (0.83 ± 0.05 vs. 0.90 ± 0.07; p = 0.009. Furthermore, over the course of the evaluation period, area under the curve assessment demonstrated that REE was significantly increased with Meltdown compared to placebo (992.5 ± 133.1 vs. 895.1 ± 296.1 kcals; p = 0.043, while RER was significantly less than placebo (5.55 ± 0.61 vs. 5.89 ± 0.44; p = 0.002 following ingestion. HR and BP were not significantly affected prior to exercise with either supplement (p > 0.05 and the exercise-induced increases for HR and BP decreased into recovery and were not different between supplements (p > 0.05. These data suggest that Meltdown enhances REE and fat oxidation more than placebo for several hours after ingestion in fully rested and

N Reactor Deactivation Program Plan

International Nuclear Information System (INIS)

Walsh, J.L.

1993-12-01

This N Reactor Deactivation Program Plan is structured to provide the basic methodology required to place N Reactor and supporting facilities · in a radiologically and environmentally safe condition such that they can be decommissioned at a later date. Deactivation will be in accordance with facility transfer criteria specified in Department of Energy (DOE) and Westinghouse Hanford Company (WHC) guidance. Transition activities primarily involve shutdown and isolation of operational systems and buildings, radiological/hazardous waste cleanup, N Fuel Basin stabilization and environmental stabilization of the facilities. The N Reactor Deactivation Program covers the period FY 1992 through FY 1997. The directive to cease N Reactor preservation and prepare for decommissioning was issued by DOE to WHC on September 20, 1991. The work year and budget data supporting the Work Breakdown Structure in this document are found in the Activity Data Sheets (ADS) and the Environmental Restoration Program Baseline, that are prepared annually

The risk of extinction - the mutational meltdown or the overpopulation

OpenAIRE

Malarz, K.

2006-01-01

The phase diagrams survival-extinction for the Penna model with parameters: (mutations rate)-(birth rate), (mutation rate)-(harmful mutations threshold), (harmful mutation threshold)-(minimal reproduction age) are presented. The extinction phase may be caused by either mutational meltdown or overpopulation. When the Verhulst factor is responsible for removing only newly born babies and does not act on adults the overpopulation is avoided and only genetic factors may lead to species extinction.

The risk of extinction - the mutational meltdown or the overpopulation.

Science.gov (United States)

Malarz, Krzysztof

2007-04-01

The phase diagrams survival-extinction for the Penna model with parameters: (mutations rate)-(birth rate), (mutation rate)-(harmful mutations threshold), (harmful mutation threshold)-(minimal reproduction age) are presented. The extinction phase may be caused by either mutational meltdown or overpopulation. When the Verhulst factor is responsible for removing only newly born babies and does not act on adults the overpopulation is avoided and only genetic factors may lead to species extinction.

Severe fuel damage in steam and helium environments observed in in-reactor experiments

International Nuclear Information System (INIS)

Saito, S.; Shiozawa, S.

1984-01-01

The bahavior of severe fuel damages has been studied in gaseous environments simulating core uncovery accidents in the in-reactor experiments utilizing the NSRR. Two types of cladding relocation modes, azimuthal flow and melt-down, were revealed through the parametric experiments. The azimuthal flow was evident in an oxidizing environment in case of no oxide film break. The melt-down can be categorized into flow-down and move-down, according to the velocity of the melt-down. Cinematographies showed that the flow-down was very fast as water flows down while the move-down appeared to be much slower. The flow-down was possible in an unoxidizing environment, whereas the move-down of molten cladding occured through a crack induced in an oxide film in an oxidizing environment. The criterion of the relocation modes was developed as a function of peak cladding temperature and oxidation condition. It was also found that neither immediate quench nor fuel fracture occurred upon flooding when cladding temperature was about 1800 0 C at water injection. The external mechanical force is needed for fuel fracture. (orig.)

Lack of Critical Slowing Down Suggests that Financial Meltdowns Are Not Critical Transitions, yet Rising Variability Could Signal Systemic Risk

Science.gov (United States)

Hoarau, Quentin

2016-01-01

Complex systems inspired analysis suggests a hypothesis that financial meltdowns are abrupt critical transitions that occur when the system reaches a tipping point. Theoretical and empirical studies on climatic and ecological dynamical systems have shown that approach to tipping points is preceded by a generic phenomenon called critical slowing down, i.e. an increasingly slow response of the system to perturbations. Therefore, it has been suggested that critical slowing down may be used as an early warning signal of imminent critical transitions. Whether financial markets exhibit critical slowing down prior to meltdowns remains unclear. Here, our analysis reveals that three major US (Dow Jones Index, S&P 500 and NASDAQ) and two European markets (DAX and FTSE) did not exhibit critical slowing down prior to major financial crashes over the last century. However, all markets showed strong trends of rising variability, quantified by time series variance and spectral function at low frequencies, prior to crashes. These results suggest that financial crashes are not critical transitions that occur in the vicinity of a tipping point. Using a simple model, we argue that financial crashes are likely to be stochastic transitions which can occur even when the system is far away from the tipping point. Specifically, we show that a gradually increasing strength of stochastic perturbations may have caused to abrupt transitions in the financial markets. Broadly, our results highlight the importance of stochastically driven abrupt transitions in real world scenarios. Our study offers rising variability as a precursor of financial meltdowns albeit with a limitation that they may signal false alarms. PMID:26761792

Risk of the research reactor BER II in Berlin

International Nuclear Information System (INIS)

Paulitz, Henrik; Hoevener, Barbara; Rosen, Alex

2015-01-01

The research reactor BER II is sited at the periphery of Berlin in the neighborhood of residential areas. The operational license is limited until December 31, 2019. The reactor is funded by the Federal Government (90%) and the city of Berlin (10%). The stress test has shown that the reactor is not secured against an aircraft crash (airliner or fast flying military jet), meltdown with remarkable radiological consequences to the public would be the consequence. Further hazards result from the radioactive waste transport, explosions and fires. The emergency measures cannot be considered to be sufficient. The city of Berlin would not be able to fulfill the required measures in case of a radiation accident.

Why Competent Persons Have Meltdowns Working with Troubled Students: A Personal Essay

Science.gov (United States)

Long, Nicholas J.

2010-01-01

How do otherwise competent helpers "lose it" in work with certain troubled children and youth? Drawing on extensive research and practice expertise, this article identifies four causes of these predictable professional "meltdowns"--(1) Caught in the Conflict Cycle; (2) Violation of cherished values and beliefs; (3) Tap-in issues; and (4) Carry-in…

Considerations concerning the strategy of corium retention in the reactor vessel

International Nuclear Information System (INIS)

2015-01-01

Third-generation nuclear reactors are characterised by consideration during design of core meltdown accidents. More specifically, dedicated measures or devices must be implemented to avoid basemat melt-through in the reactor building. These devices must have a high level of confidence. The strategy of corium retention in the reactor vessel, if supported by appropriate research and development, makes it possible to achieve this objective. IRSN works alone or in partnerships to address all the issues associated with in-vessel corium retention. This document describes the in-vessel corium retention strategy and its limitations, along with the research programs conducted by IRSN in this area

Aerosol retention during SGTR meltdown sequences under different conditions of tubes vibration

International Nuclear Information System (INIS)

Delgado Tardaguila, R.; Herranz, L. E.

2014-01-01

The containment bypass of the fission products during SGTR meltdown sequences makes this scenario be a significant risk contributor in PWRs. The EU-SGTR, ARTIST 1 and 2 and the on-going ARTIST-extension programs have investigated the potential attenuation of the source term reaching the secondary side of a failed SG even in the absence of water. (Author)

Contamination transfer in the meltdown of a fast reactor. Inverse Leidenfrost phenomenon

International Nuclear Information System (INIS)

Eddi, Michel.

1980-12-01

Sodium is used as a coolant in so-called breeder reactors. The safety problems encountered with this type of reactor are due to the high power densities dissipated in the medium at high temperatures. The consequences to the plant and the environment of the inability to evacuate such power coupled with a failure in the system used to shut down the reactor has evidently been studied in safety analyses. The reactor must be calculated and built so that the integrity of the containment is guaranteed and no contamination whatsoever observed outside the buildings of the plant. Such a sequence (designated: overall accident) would lead to the melting or vaporization of part of the fuel followed by a violent interaction between the sodium and UO 2 powder. The conditions of this violent interaction (also designated: vapor explosion) are examined in the text. A single or several bubbles containing sodium in two phases, incondensable fission gases (xenon, krypton and argon), fission products together with UO 2 , PuO 2 , steels and structural materials in the form of highly contamined liquid or solid aerosols would then be formed. If the leaktightness of the roof slab was no longer assured (explosive phase), a leak involving sodium and radioactive products would occur. The aim of the work described was to study the behavior of the aerosols present in the reacting medium in order to determine the quantity of contamination transported by the bubble to the roof of the vessel. This quantity will be the source term for a possible pollution outside the vessel [fr

Acoustic Waves: A Route to Enhance Sodium Fast Reactor Safety

International Nuclear Information System (INIS)

Jeannot, Jean-Philippe; Baque, François; Cavaro, Matthieu; Gastaldi, Olivier; Lhuilier, Christian; Massacret, Nicolas; Moriot, Jérémy; Paumel, Kévin; Vandergaegen, Matthias; Rodriguez, Gilles

2013-01-01

Improvement to prevent core meltdown and to provide a more robust safety demonstration → Safety objectives: - A level of safety at least equivalent to EPR’s level, - Consolidation of the defence-in-depth principle, - A more robust safety demonstration than those of the Phenix and Superphenix reactor. Acoustic techniques: - Low attenuation by the sodium medium - High velocity of US wave (2289 m.s-1 at 550°C) →

COPING WITH GLOBAL MELTDOWN: INDIA’S EXTERNAL SECTOR

Directory of Open Access Journals (Sweden)

Nandita Sethi

2011-07-01

Full Text Available n 2008 the world economy landed itself in the midst of the most severe financial recession which originated in the developed countries and spread to the developing countries which were hit hard through capital reversals, rising borrowing costs, collapsing world trade and commodity prices, and subsiding remittances. India’s engagement with the global economy became deeper from the 1990s and this made it inevitable to be affected by the global meltdown. This paper attempts to analyze the impact of the global recession on the external sector of the Indian economy. A pre and post recession (2008 analysis is undertaken to see the impact on trade, capital flows, exchange rates and foreign exchange reserves and external debt. The analysis reveals that while India was adversely impacted due to the slowdown in trade, capital flows and outsourcing; the impact has not been as much as in many other Asian economies. The capital flows were soon back, as India seemed like a save haven for funds with reasonable growth and interest rates. The Indian banking and regulatory system has been credited for following prudential norms and India’s huge domestic market and fiscal stimulus have got the economy almost back on track with growth rates looking up again.

Safety analysis of RA reactor operation, I-III, Part III - Environmental effect of the maximum credible accident

International Nuclear Information System (INIS)

Raisic, N.

1963-02-01

Maximum credible accident at the RA reactor would consider release of fission products into the environment. This would result from fuel elements failure or meltdown due to loss of coolant. The analysis presented in this report assumes that the reactor was operating at nominal power at the moment of maximum possible accident. The report includes calculations of fission products activity at the moment of accident, total activity release during the accident, concentration of radioactive material in the air in the reactor neighbourhood, and the analysis of accident environmental effects

Comparison of computer codes relative to the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Bunz, H.; Dunbar, I.; Gauvain, J.; Ricchena, R.

1986-01-01

The present study concerns a comparative exercise, performed within the framework of the Commission of the European Communities, of the computer codes (AEROSIM-M, UK; AEROSOLS/B1, France; CORRAL-2, CEC and NAUA Mod5, Germany) used in order to assess the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR. Topics considered in this paper include aerosols, containment buildings, reactor safety, fission product release, reactor cores, meltdown, and monitoring

E-beam heated linear solenoid reactors

International Nuclear Information System (INIS)

Benford, J.; Bailey, V.; Oliver, D.

1976-01-01

A conceptual design and system analysis shows that electron beam heated linear solenoidal reactors are attractive for near term applications which can use low gain fusion sources. Complete plant designs have been generated for fusion based breeders of fissile fuel over a wide range of component parameters (e.g., magnetic fields, reactor lengths, plasma densities) and design options (e.g., various radial and axial loss mechanisms). It appears possible that a reactor of 100 to 300 meters length operating at power levels of 1000 MWt can economically produce 2000 to 8000 kg/yr of 233 U to supply light water reactor fuel needs beyond 2000 A.D. Pure fusion reactors of 300 to 500 meter lengths are possible. Physics and operational features of reactors are described. Beam heating by classical and anomalous energy deposition is reviewed. The technology of the required beams has been developed to MJ/pulse levels, within a factor of 20 of that needed for full scale production reactors. The required repetitive pulsing appears practical

Serious reactor accidents reconsidered

International Nuclear Information System (INIS)

1987-12-01

The chance is determined for damage of the reactor core and that sequel events will cause excursion of radioactive materials into the environment. The gravity of such an accident is expressed by the source term. It appears that the chance for such an accident varies with the source term. In general it is valid that how larger the source term how smaller the chance is for it and vice versa. The chance for excursion is related to two complexes of events: serious damage (meltdown) of the reactor core, and the escape of the liberated radionuclides into the environment. The results are an order of magnitude consideration of the relation between the extent of the source term and the chance for it. From the spectrum of possible source terms three representative ones have been chosen: a large, a medium and a relative small source term. This choice is in accordance with international considerations. The hearth of this study is the estimation of the chance for occurrence of the three chosen source terms for new light-water reactors. refs.; figs.; tabs

Containment loadings due to hydrogen burning in LWR core meltdown accidents

International Nuclear Information System (INIS)

Cybulskis, P.

1981-01-01

The potential pressure loadings due to hydrogen burning under conditions representative of meltdown accident conditions are examined for a variety of PWR and BWR containment designs. For the PWR, the large dry, ice condenser, as well as subatmospheric containments are considered. For the BWR, MARK I, II, and III pressure suppression containments are evaluated. The key factors considered are: free volume, design pressure, extend to hydrogen generation, and the flammability of the atmosphere under a range of accident conditions. The potential for and the possible implications of hydrogen detonation are also considered. The results of these analyses show that the accumulation and rapid burning of the quantities of hydrogen that would be generated during core meltdown accidents will lead to pressures above design levels in all of the containments considered. As would be expected, containments characterized by small volumes and/or low design pressures are the most vulnerable to damage due to hydrogen burning. Large volume, high pressure designs may also be threatened but offer significantly more potential for accomodating hydrogen burns. The attainment of detonable hydrogen mixtures is made easier by smaller containment volumes. Detonable mixtures are also possible in the larger volume containments, but imply the accumulation of hydrogen for long periods of time without prior ignition. Hydrogen detonations, if they occur, would probably challenge the integrity of any of the containments considered. (orig.)

Investigation of the failure of a reactor pressure vessel by plastic instability

International Nuclear Information System (INIS)

Laemmer, H.; Ritter, B.

1994-01-01

A possible consequence of a core meltdown accident in a pressurized water reactor is the failure of the reactor pressure vessel under high internal pressure. With the aid of the finite element program ABAQUS and using a material model of the thermo-plasticity for large deformation, the failure of the reactor pressure vessel due to plastic instability was examined. It was apparent from the finite element calculations that solely due to reduction in strength of the material, even for internal wall temperatures clearly below the core melt; of about 2000 C, the critical internal pressure can fall to values which are lower than the working pressure. With the aid of simplified geometry, a lower limit for the pressure at failure of the reactor pressure vessel can be calculated. (orig./HP) [de

A theory of modern cultural shifts and meltdowns.

Science.gov (United States)

Hochberg, Michael E

2004-08-07

Many cultural attributes such as adornment, language slang, mannerisms and rituals are thought to have little or no influence on individual survival and reproduction, functioning rather as markers of cultural identity that promote group cohesion. Here, I show that if cultural markers are under weak selection and subject to loss or substitution, then the breakdown of cultural cohesiveness may proceed without stabilizing reactions until many or most of a culture's identifiers are forever lost. This may culminate in a 'cultural meltdown', whereby the culture is caught in a vortex of ever-decreasing membership and insufficient selection against the accumulation of unfamiliar markers. In progressively altering the topology of communication from diffusion to broadcasting, globalization may be both accelerating the erosion of cultural identities and amplifying dominance behaviours above their normal adaptive levels.

Methodological aspects of core meltdown accidents frequency estimates

International Nuclear Information System (INIS)

Matthis, P.

1984-01-01

A survey is given of the work of the ecological institute relating to models and methods used in the German Risk Study for the assessment of core meltdown accident frequency. A statistical model used by the ecological institute for the estimation of the outage behaviour of components is taken as a comparison, which leads to the conclusion that no appropriate methods for the assessment of component reliability are available to date. Furthermore, there are no secured methods for error propagation computation. The lower limits for the ranges of reliability of components are calculated by approximation. As a result of imperfect modelling and of a number of methodical inaccuracies and neglects, the German Risk Study underestimates the ranges of component reliability by a factor of 3 to 70 (depending on the type of component). (RF) [de

Reports on BMBF-sponsored research projects in the field of reactor safety. Reporting period 1 July - 31 December 1995

International Nuclear Information System (INIS)

1996-01-01

The Gesellschaft fuer Anlagen- und Reaktorsicherheit informs of the status of LWR tasks and projects on the safety of advanced reactors. Each progress report represents a compilation of individual reports about objectives, the work performed, the results, and the next steps of the works. The individual reports of quality assurance, safety of reactor component, emergency core cooling, lors of coolant, meltdown, fission product release, risk and reliability, are classified according to projects to the reactor safety research program. Another table uses the same classification system as applied in the nuclear safety index of the CEC. (DG)

Design review of the N Reactor

International Nuclear Information System (INIS)

1986-09-01

This review of the design features of the N Reactor was initiated at the request of the Secretary of Energy, John S. Herrington, shortly after, and as a consequence of, reports of the accident at the Soviet reactor complex located at Chernobyl, on April 26, 1986. In the review, special attention was given to those plant systems which are most important in preventing the release of radioactive materials from the plant in the event of combined major equipment failures and human errors. Also, the review studied the potential effects of various severe accident sequences, and addressed the question of whether an event similar in causes or consequences to the Chernobyl accident could occur in the N Reactor. In light of experiences at both Three Mile Island and Chernobyl, the potential for accumulation of hydrogen in excess of flammable limits was given particular attention. The review team was also asked to identify possible improvements to the N Reactor plant, and to evaluate the effects and significance of service-induced degradation. The overall conclusion of the design review is that the N Reactor is safe to operate and that there is no reason to stop or alter its operation in any major respect at this time. Certain additional analyses and testing, are recommended to provide a firmer basis for decisions on long-term operation and on measures which may be needed in the future to accommodate long-term operation

Risk of the research reactor BER II in Berlin; Risiken des Berliner Experimentierreaktors BER II

Energy Technology Data Exchange (ETDEWEB)

Paulitz, Henrik; Hoevener, Barbara; Rosen, Alex

2015-04-20

The research reactor BER II is sited at the periphery of Berlin in the neighborhood of residential areas. The operational license is limited until December 31, 2019. The reactor is funded by the Federal Government (90%) and the city of Berlin (10%). The stress test has shown that the reactor is not secured against an aircraft crash (airliner or fast flying military jet), meltdown with remarkable radiological consequences to the public would be the consequence. Further hazards result from the radioactive waste transport, explosions and fires. The emergency measures cannot be considered to be sufficient. The city of Berlin would not be able to fulfill the required measures in case of a radiation accident.

Requirements for light water reactors

International Nuclear Information System (INIS)

Hedin, F.

2009-01-01

The EUR (European Utilities Requirements) is an organization founded in 1991 whose aim was to write down the European specifications and requirements for the future reactors of third generation. EUR gathers most of the nuclear power producers of Europe. The EUR document has been built on the large and varied experience of EUR members and can be used to elaborate invitations to tender for nuclear projects. 4000 requirements only for the nuclear part of the plant are listed, among which we have: -) the probability of core meltdown for a reactor must be less than 10 -6 per year, -) the service life of every component that is not replaceable must be 60 years, -) the capacity of the spent fuel pool must be sufficient to store 10-15 years of production without clearing out. The EUR document is both open and complete: every topic has been considered, it does not favor any type of reactor but can ban any technology that is too risky or has an unfavourable feedback experience. The assessment of the conformity with the EUR document of 7 reactor projects (BWR 90/, EPR, EP1000, SWR1000, ABWR, AP1000 and VVER-AES-92) has already be made. (A.C.)

Operational report, basics of the preliminary project for reconstruction of the RA reactor ventilation system

International Nuclear Information System (INIS)

Martinc, R.

1982-01-01

This report presents the summary of results needed for designing the reconstruction of the RA reactor ventilation system. The final complete report will published later, including results of possible additional analyses according to the needs of main detailed project. Due to the size of the facility the need of filters for particulates is expected in systems V-1 and V-2, as well as revision of the system V-4. Adsorption filters are not needed in case of operation under regular working conditions. It would be favorable, but not indispensable to construct an adsorption filter that could be used occasionally at the input of V-2 system under the upper water shielding. This filter would be switched on when dehermetization of the reactor is planned and increased radioactivity is indicated in the gas system or experimental space of the RA reactor as well as in case of fuel elements failure. The aim of applying filters is shortening the time these elements would spend in the hermetized reactor i.e. their fast removal from the reactor. It is indispensable to build-in 'emergency' highly efficient adsorption filters in the V-2 system which would be switched on in case of accidents that would cause fuel elements meltdown (with simultaneous accident dehermetization of the heavy water system) [sr

Reactor safety research against the backdrop of the Energy-Omnibus Law

International Nuclear Information System (INIS)

Kuczera, B.

1995-01-01

On July 19, 1994, the German Federal Parliament adopted the Coal/Nuclear Power Omnibus Law, in which a new quality of safety of future nuclear power plants has been laid down. The defense-in-depth safety concept underlying the nuclear power plants currently in operation is derived from the principle of safety precautions made against reactor accidents, and encompasses preventive measures of accident mangement and mitigating measures of containing possible consequences. Accident management leads to the requirement that even in the most unlikely accidents with core meltdown the consequences remain limited to the plant. A new quality in reactor safety is represented by the System 80+ advanced pressurized water reactor and by the European Pressurized Water Reactor, EPR. Despite different views about the approaches used to address individaul aspects in the achievement of safety goals, there is agreement on the principle that risk provisions, by achieving more transparency, are to result in better public acceptance of the peaceful uses of nuclear power. (orig.) [de

REMOCIÓN DE ARSÉNICO (V ASISTIDA POR OXIDACIÓN UV SOLAR EN UN FOTO-REACTOR TUBULAR DE SECCIÓN CIRCULAR

Directory of Open Access Journals (Sweden)

Ramiro Escalera Vásquez

2010-01-01

Full Text Available Se ha construido y caracterizado un foto-reactor tubular de sección circular para su aplicación al tratamiento de aguas subterráneas contaminadas con Arsénico, As(V, utilizando las técnica de la Remoción de Arsénico por Oxidación Solar (RAOS. El concentrador solar que posee una capacidad de radiación equivalente a 2,8 soles, fue construido reciclando materiales desechados: tubos de vidrio proveniente de lámparas de Ne y tubos de desagüe sanitario de 6” (PVC, recubiertos por láminas de aluminio. Pruebas simultáneas sin agitación,realizadas aplicando la radiación UV solar a aguas sintéticas, demostraron que la remoción de As(V en el foto-reactor es más rápida queen un tubo de vidrio sólo y en una botella PET de 2 litros, logrando remociones mayores al 98% en todos los casos. Los tiempos para la aparición de los flóculos de complejo Fe-citrato fueron de 40, 50 y 90 min respectivamente, para intensidades de radiación UVA integral (290-390 nm entre 50 y 70 Wm-2. Pruebas de irradiación seguidas de agitación controlada a 30-33 s-1 de gradiente de velocidad, demostraron que el foto-reactor acelera el proceso de formación de flóculos fácilmente sedimentables al cabo de 20-30 min de agitación. Los tiempos de irradiación óptimos para el foto-reactor, el tubo y la botella son de 15, 25 y 60 min, respectivamente. Pruebas en régimen de flujo continuo en un foto-reactor de aproximadamente 1 m2 de área, con un tiempo de residencia hidráulica (igual al tiempo de irradiación de 15 min, mostraron la formación inmediata de flóculos fácilmente sedimentables cuando se agitan a 33 s-1 durante 20-30 min, lográndose una remoción del 98,36% una concentración remanente de 16,5 mgL-1 de As(V en aguas decantadas. Esto significa que se pueden tratar aproximadamente 130 Lm-2 en una jornada de 6 horas de radiación UVA de 50-70 Wm-2 de intensidad.

Numerical investigation on turbulent natural convection in partially connected cylindrical enclosures for analysing SFR safety under core meltdown scenario

International Nuclear Information System (INIS)

David, Dijo K.; Mangarjuna Rao, P.; Nashine, B.K.; Selvaraj, P.

2015-01-01

Under the unlikely event of severe core meltdown accident in pool type SFR, the molten core materials may rupture the grid plate which supports the fuel subassemblies and it can get relocated in to the lower pool. These debris may eventually settle on the debris collector (i.e., core catcher) installed above the bottom wall of the lower pool. The bed thus formed generates heat due to radioactive decay which has to be passively removed for maintaining the structural integrity of main vessel. By means of natural convection, the heat generated in the debris bed will be transferred to the top pool where the heat sink (i.e., Decay heat exchanger (DHX)) is installed. Heat transfer to the DHX (which is a part of safety grade decay heat removal system) can take place through the opening created in the grid plate which connects the two liquid pools (i.e., the top pool and the lower pool). Heat transfer can also take place through the lateral wall of the lower cylindrical pool to the side pool and eventually to the top pool, and thus to the DHX. This study numerically investigates the effectiveness of heat transfer between lower pool and top pool during PARR by considering them as partially connected cylindrical enclosures. The governing equations have been numerically solved using finite volume method in cylindrical co-ordinates using SIMPLE algorithm. Turbulence has been modeled using k-ω model and the model is validated against benchmark problems of natural convection found in literature. The effect of parameters such as the heat generation rate in the bed and the size of the grid plate opening are evaluated. Also PAHR in SFR pool is modeled using an axi-symmetric model to fund out the influence of grid plate opening on heat removal from core catcher. The results obtained are useful for improving the cooling capability of in-vessel tray type core catcher for handling the whole core meltdown scenarios in SFR. (author)

Evaluación del comportamiento hidrodinámico como herramienta para optimización de reactores anaerobios de crecimiento en medio fijo

Directory of Open Access Journals (Sweden)

Andrea Pérez

2008-01-01

Full Text Available Las condiciones de flujo no ideal en los reactores afectan su desempeño; las causas comunes son cortos circuitos, zonas muertas y recirculación interna por corrientes cinéticas y/o de densidad. En este estudio se optimizó el diseño de un filtro anaerobio a escala real que trata las aguas residuales del proceso de extracción de almidón de yuca, el cual presentaba problemas de represamiento y bajas eficiencias de remoción. La evaluación del comportamiento hidrodinámico inicial mostró la presencia de flujo dual (32% flujo pistón - FP y 37% mezcla completa - CM, zonas muertas (20% y ausencia de cortos circuitos; adicionalmente, la modelación del reactor indicó un grado de dispersión elevado y un comportamiento tendiente a un reactor CM en serie de dos unidades. Con base en estos resultados, se implementaron dos modificaciones en el diseño del reactor: falso fondo y tubería perforada para evacuación de biogás, las cuales permitieron incrementar la fracción de FP (44%, reducir la fracción de zonas muertas (15%, disminuir el Índice de Dispersión (ID e incrementar la tendencia del reactor a un CM en serie de tres unidades, lo que aumentó el tiempo de retención hidráulico (TRH real de 9,6 a 10,2 horas (TRH teórico 12 horas y las eficiencias teóricas de remoción de 73 a 78%.

International Reactor Physics Experiment Evaluation (IRPhE) Project. IRPhE Handbook - 2015 edition

International Nuclear Information System (INIS)

Bess, John D.; Gullifor, Jim

2015-03-01

The purpose of the International Reactor Physics Experiment Evaluation (IRPhE) Project is to provide an extensively peer-reviewed set of reactor physics-related integral data that can be used by reactor designers and safety analysts to validate the analytical tools used to design next-generation reactors and establish the safety basis for operation of these reactors. This work of the IRPhE Project is formally documented in the 'International Handbook of Evaluated Reactor Physics Benchmark Experiments', a single source of verified and extensively peer-reviewed reactor physics benchmark measurements data. The evaluation process entails the following steps: Identify a comprehensive set of reactor physics experimental measurements data, Evaluate the data and quantify overall uncertainties through various types of sensitivity analysis to the extent possible, verify the data by reviewing original and subsequently revised documentation, and by talking with the experimenters or individuals who are familiar with the experimental facility, Compile the data into a standardized format, Perform calculations of each experiment with standard reactor physics codes where it would add information, Formally document the work into a single source of verified and peer reviewed reactor physics benchmark measurements data. The International Handbook of Evaluated Reactor Physics Benchmark Experiments contains reactor physics benchmark specifications that have been derived from experiments that were performed at nuclear facilities around the world. The benchmark specifications are intended for use by reactor designers, safety analysts and nuclear data evaluators to validate calculation techniques and data. Example calculations are presented; these do not constitute a validation or endorsement of the codes or cross-section data. The 2015 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments contains data from 143 experimental series that were

Investigation of activity release during light water reactor core meltdown

International Nuclear Information System (INIS)

Albrecht, H.; Matschoss, V.; Wild, H.

1978-01-01

A test facility was developed for the determination of activity release and of aerosol characteristics under realistic light water reactor core melting conditions. It is composed of a high-frequency induction furnace, a ThO 2 crucible system, and a collection apparatus consisting of membrane and particulate filters. Thirty-gram samples of a representative core material mixture (corium) were melted under air, argon, or steam at 0.8 to 2.2 bar. In air at 2700 0 C, for example, the relative release was 0.4 to 0.7% for iron, chromium, and cobalt and 4 to 11% for tin, antimony, and manganese. Higher release values of 20 to 40% at lower temperatures (2150 0 C, air) were found for selenium, cadmium, tellurium, and cesium. The size distribution of the aerosol particles was trimodal with maxima at diameters of 0.17, 0.30, and 0.73 μm. The result of a qualitative x-ray microanalysis was that the main elements of the melt were contained in each aerosol particle. Further investigations will include larger melt masses and the additional influence of concrete on the release and aerosol behavior

Consideration of BORAX-type reactivity accidents applied to research reactors

International Nuclear Information System (INIS)

Couturier, Jean; Meignen, Renaud; Bourgois, Thierry; Biaut, Guillaume; Mireau, Jean-Pierre; Natta, Marc

2011-01-01

Most of the research reactors discussed in this document are pool-type reactors in which the reactor vessel and some of the reactor coolant systems are located in a pool of water. These reactors generally use fuel in plate assemblies formed by a compact layer of uranium (or U 3 Si 2 ) and aluminium particles, sandwiched between two thin layers of aluminium serving as cladding. The fuel melting process begins at 660 deg. C when the aluminium melts, while the uranium (or U 3 Si 2 ) particles may remain solid. The accident that occurred in the American SL-1 reactor in 1961, together with tests carried out in the United States as of 1954 in the BORAX-1 reactor and then, in 1962, in the SPERT-1 reactor, showed that a sudden substantial addition of reactivity in this type of reactor could lead to explosive mechanisms caused by degradation, or even fast meltdown, of part of the reactor core. This is what is known as a 'BORAX-type' accident. The aim of this document is first to briefly recall the circumstances of the SL-1 reactor accident, the lessons learned, how this operational feedback has been factored into the design of various research reactors around the world and, second, to describe the approach taken by France with regard to this type of accident and how, led by IRSN, this approach has evolved in the last decade. (authors)

Plant-scale anodic dissolution of unirradiated N-Reactor fuel

International Nuclear Information System (INIS)

Gay, E.C.; Miller, W.E.; Laidler, J.J.

1995-01-01

Anodic dissolution tests were made with unirradiated N-Reactor fuel to determine the fuel segment length, diameter, and shape required for high throughput electrorefiner treatment for ultimate disposal in a geologic repository. Based on these tests, a conceptual design was produced of an electrorefiner for a full-scale plant to process N-Reactor spent fuel. In this design, the diameter of an electrode assembly is about 0.6 m (25 in.). Eight of these assemblies in an electrorefiner would accommodate a 1.333-metric-ton batch of N-Reactor fuel. Electrorefining would proceed at a rate of 40 kg uranium per hour

Continuous formation of N-chloro-N,N-dialkylamine solutions in well-mixed meso-scale flow reactors

Science.gov (United States)

Jolley, Katherine E

2015-01-01

Summary The continuous flow synthesis of a range of organic solutions of N,N-dialkyl-N-chloramines is described using either a bespoke meso-scale tubular reactor with static mixers or a continuous stirred tank reactor. Both reactors promote the efficient mixing of a biphasic solution of N,N-dialkylamine in organic solvent, and aqueous sodium hypochlorite to achieve near quantitative conversions, in 72–100% in situ yields, and useful productivities of around 0.05 mol/h with residence times from 3 to 20 minutes. Initial calorimetric studies have been carried out to inform on reaction exotherms, rates and safe operation. Amines which partition mainly in the organic phase require longer reaction times, provided by the CSTR, to compensate for low mass transfer rates in the biphasic system. The green metrics of the reaction have been assessed and compared to existing procedures and have shown the continuous process is improved over previous procedures. The organic solutions of N,N-dialkyl-N-chloramines produced continuously will enable their use in tandem flow reactions with a range of nucleophilic substrates. PMID:26734089

Continuous formation of N-chloro-N,N-dialkylamine solutions in well-mixed meso-scale flow reactors

Directory of Open Access Journals (Sweden)

A. John Blacker

2015-12-01

Full Text Available The continuous flow synthesis of a range of organic solutions of N,N-dialkyl-N-chloramines is described using either a bespoke meso-scale tubular reactor with static mixers or a continuous stirred tank reactor. Both reactors promote the efficient mixing of a biphasic solution of N,N-dialkylamine in organic solvent, and aqueous sodium hypochlorite to achieve near quantitative conversions, in 72–100% in situ yields, and useful productivities of around 0.05 mol/h with residence times from 3 to 20 minutes. Initial calorimetric studies have been carried out to inform on reaction exotherms, rates and safe operation. Amines which partition mainly in the organic phase require longer reaction times, provided by the CSTR, to compensate for low mass transfer rates in the biphasic system. The green metrics of the reaction have been assessed and compared to existing procedures and have shown the continuous process is improved over previous procedures. The organic solutions of N,N-dialkyl-N-chloramines produced continuously will enable their use in tandem flow reactions with a range of nucleophilic substrates.

Preliminary design of a borax internal core-catcher for a gas cooled fast reactor

International Nuclear Information System (INIS)

Dalle Donne, M.; Dorner, S.; Schumacher, G.

1976-09-01

Preliminary thermal calculations show that a core-catcher appears to be feasible, which is able to cope with the complete meltdown of the core and blankets of a 1,000 MWe GCFR. This core-catcher is based on borax (Na 2 B 4 O 7 ) as dissolving material of the oxide fuel and of the fission products occuring in oxide form. The borax is contained in steel boxes forming a 2.1 meter thick slab on the base of the reactor cavity inside the prestressed concrete reactor vessel, just underneath the reactor core. The fission products are dispersed in the pool formed by the liquid borax. The heat power density in the pool is conveniently reduced and the resulting heat fluxes at the borders of the pool can be safely carried away through the PCRV liner and its water cooling system. (orig.) [de

RA reactor safety analysis I-III, Part III - Environmental effect of the maximum credible accident; Analiza sigurnosti rada Reaktora RA I-III, III deo - Posledica maksimalno moguceg akcidenta na okolinu reaktora

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

The objective of the maximum credible accident analysis was to determine the integral radiation doses in the vicinity of the reactor and in the environment. In case of RA reactor the maximum credible accident, meaning release of the fission products, would be caused by fuel elements meltdown. This analysis includes the following calculation results: activity of the fission products, volatility of the fission products, concentration of radioactive materials in the air, analysis of the accident environmental effects.

Graphite surveillance in N Reactor

International Nuclear Information System (INIS)

Woodruff, E.M.

1991-09-01

Graphite dimensional changes in N Reactor during its 24 yr operating history are reviewed. Test irradiation results, block measurements, stack profiles, top of reflector motion monitors, and visual observations of distortion are described. 18 refs., 14 figs., 1 tab

Safety analysis of RA reactor operation, I-III, Part III - Environmental effect of the maximum credible accident; Analiza sigurnosti rada reaktora RA - I-III, III deo - Posledica maksimalno moguceg akcidenta na okolinu reaktora

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

Maximum credible accident at the RA reactor would consider release of fission products into the environment. This would result from fuel elements failure or meltdown due to loss of coolant. The analysis presented in this report assumes that the reactor was operating at nominal power at the moment of maximum possible accident. The report includes calculations of fission products activity at the moment of accident, total activity release during the accident, concentration of radioactive material in the air in the reactor neighbourhood, and the analysis of accident environmental effects.

Epitaxial growth of GaN/AlN/InAlN heterostructures for HEMTs in horizontal MOCVD reactors with different designs

Energy Technology Data Exchange (ETDEWEB)

Tsatsulnikov, A. F., E-mail: andrew@beam.ioffe.ru; Lundin, W. V.; Sakharov, A. V.; Zavarin, E. E.; Usov, S. O.; Nikolaev, A. E.; Yagovkina, M. A.; Ustinov, V. M. [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation); Cherkashin, N. A. [CEMES–CNRS—Université de Toulouse (France)

2016-09-15

The epitaxial growth of InAlN layers and GaN/AlN/InAlN heterostructures for HEMTs in growth systems with horizontal reactors of the sizes 1 × 2', 3 × 2', and 6 × 2' is investigated. Studies of the structural properties of the grown InAlN layers and electrophysical parameters of the GaN/AlN/InAlN heterostructures show that the optimal quality of epitaxial growth is attained upon a compromise between the growth conditions for InGaN and AlGaN. A comparison of the epitaxial growth in different reactors shows that optimal conditions are realized in small-scale reactors which make possible the suppression of parasitic reactions in the gas phase. In addition, the size of the reactor should be sufficient to provide highly homogeneous heterostructure parameters over area for the subsequent fabrication of devices. The optimal compositions and thicknesses of the InAlN layer for attaining the highest conductance in GaN/AlN/InAlN transistor heterostructures.

Plant-scale anodic dissolution of unirradiated N-Reactor fuel

International Nuclear Information System (INIS)

Gay, E.C.; Miller, W.E.; Laidler, J.J.

1995-01-01

Anodic dissolution tests were made with unirradiated N-Reactor fuel to determine the fuel segment length, diameter, and shape required for high throughput electro-refiner treatment for ultimate disposal in a geologic repository. Based on these tests, a conceptual design was produced of an electro-refiner for a full-scale plant to process N-Reactor spent fuel. In this design, the diameter of an electrode assembly is about 0.6 m (25 in.). Eight of these assemblies in an electro-refiner would accommodate a 1.333-metric-ton batch of N-Reactor fuel. Electrorefining would proceed at a rate of 40 kg uranium per hour. (author)

Calculations of radiation defect formation cross sections in reactor materials in (n,p) and (n,α) reactions

International Nuclear Information System (INIS)

Kupchishin, A.A.; Kupchishin, A.I.; Omarbekova, Zh.

2001-01-01

In the work an experimental data analysis by integral σ(E 1 ) and differential [dσ(E 1 ,E 2 )]/dE 2 neutron interaction cross sections with reactor materials with the secondary protons and alpha particles generation as well as with the primarily knock-on atoms production in such reactions are carried out. It is shown, that in the (n,p) and (n',α) reactions the recoil nuclei receive essential energy portion and they are the patriarchs for atom-atom cascades in the substance. Nuclear reactions with formation of the secondary α-particles and and recoil nuclei are considered. It is shown, that these reactions are effectively proceeding within neutrons energy range 0.3-15 MeV. The nuclear reactions kinematics of above mentioned processes is studied. Energy conservation law for these reaction is applied. Deferential cross section conservation and transformation law for radiation defect formation in the (n,α) reaction are considered as well

Análisis de la dispersión axial de masa y calor en reactores de lecho fijo

Directory of Open Access Journals (Sweden)

Rangel Jara Hermes Augusto

1997-01-01

Full Text Available Dentro del espíritu investigativo a nivel teórico del estudio de los reactores químicos, el presente trabajo desarrolla e implementa un análisis conceptual y numérico de los fenómenos de dispersión axial de calor y masa en reactores de lecho fijo. Se pretende disponer de una alternativa numérica que permita en una forma rápida y precisa la solución de las ecuaciones diferenciales junto con las respectivas condiciones de frontera del modelo matemático. Para la simulación del reactor de lecho fijo se empleó un modelo unidimensional pseudohomogeneo con parámetros aglomerados.

Measurement of the^ 235U(n,n')^235mU Integral Cross Section in a Pulsed Reactor

Science.gov (United States)

Vieira, D. J.; Bond, E. M.; Belier, G.; Meot, V.; Becker, J. A.; Macri, R. A.; Authier, N.; Hyneck, D.; Jacquet, X.; Jansen, Y.; Legrendre, J.

2009-10-01

We will present the integral measurement of the neutron inelastic cross section of ^235U leading to the 26-minute, E*=76.5 eV isomer state. Small samples (5-20 microgm) of isotope-enriched ^235U were activated in the central cavity of the CALIBAN pulsed reactor at Valduc where a nearly pure fission neutron spectrum is produced with a typical fluence of 3x10^14 n/cm^2. After 30 minutes the samples were removed from the reactor and counted in an electrostatic-deflecting electron spectrometer that was optimized for the detection of ^235mU conversion electrons. From the decay curve analysis of the data, the 26-minute ^235mU component was extracted. Preliminary results will be given and compared to gamma-cascade calculations assuming complete K-mixing or with no K-mixing.

Sedimentación, solubilización, y prefermentación de aguas residuales en un reactor biopelícula

OpenAIRE

Cuevas-Rodríguez, Germán; Tejero Monzón, Iñaki

2003-01-01

Esta investigación fue realizada con el objetivo de desarrollar un nuevo reactor prefermentador de aguas residuales para incrementar los porcentajes de sedimentación, hidrólisis y prefermentación de la materia orgánica contenida en el agua residual bruta, empleando una sola unidad de pretratamiento y, de esta manera, poder remplazar el decantador primario por este nuevo reactor. El estudio fue realizado en un reactor biopelícula de lecho sumergido fijo, empacado con un medio de soporte BLASF‚...

Nuclear energy. The innovations of the N4 reactor

International Nuclear Information System (INIS)

Anon.

1998-01-01

The coupling to the electric network of the two first units of N4 type reactors, on the site of Chooz in the Ardennes, marks the third great step of the French nuclear programme of PWR type reactors, after the realization of 34 units of 900 MWe and 20 units of 1300 M We. The nuclear boiler N4, realizes a new evolution in power, in performances and in reliability. (N.C.)

C-Reactor I and E loading instability limits

Energy Technology Data Exchange (ETDEWEB)

Hess, K.W.

1957-01-24

The pilot charging of I & E fuel elements has been implemented at C-Reactor under Production Test IP-19-A. It was necessary to provide adequate tube protection against flow interruption by establishing proper trip setting on the Panellit pressure gauges. the administration of these Panellit trip settings is done by trip-before- boiling tube outlet temperature limits, which are similar in principle to the current instability limits. Trip-before-boiling limits for C-Reactor I & E fuel elements loadings are presented in this document.

A review of experiments and results from the transient reactor test (TREAT) facility

International Nuclear Information System (INIS)

Deitrich, L. W.

1998-01-01

The TREAT Facility was designed and built in the late 1950s at Argonne National Laboratory to provide a transient reactor for safety experiments on samples of reactor fuels. It first operated in 1959. Throughout its history, experiments conducted in TREAT have been important in establishing the behavior of a wide variety of reactor fuel elements under conditions predicted to occur in reactor accidents ranging from mild off normal transients to hypothetical core disruptive accidents. For much of its history, TREAT was used primarily to test liquid-metal reactor fuel elements, initially for the Experimental Breeder Reactor-II (EBR-II), then for the Fast Flux Test Facility (FFTF), the Clinch River Breeder Reactor Plant (CRBRP), the British Prototype Fast Reactor (PFR), and finally, for the Integral Fast Reactor (IFR). Both oxide and metal elements were tested in dry capsules and in flowing sodium loops. The data obtained were instrumental in establishing the behavior of the fuel under off-normal and accident conditions, a necessary part of the safety analysis of the various reactors. In addition, TREAT was used to test light-water reactor (LWR) elements in a steam environment to obtain fission-product release data under meltdown conditions. Studies are now under way on applications of TREAT to testing of the behavior of high-burnup LWR elements under reactivity-initiated accident (RIA) conditions using a high-pressure water loop

Propagation calculation for reactor cases

Energy Technology Data Exchange (ETDEWEB)

Yang Yanhua [School of Power and Energy Engineering, Shanghai Jiao Tong Univ., Shanghai (China); Moriyama, K.; Maruyama, Y.; Nakamura, H.; Hashimoto, K. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2000-11-01

The propagation of steam explosion for real reactor geometry and conditions are investigated by using the computer code JASMINE-pro. The ex-vessel steam explosion is considered, which is described as follow: during the accident of reactor core meltdown, the molten core melts a hole at the bottom of reactor vessel and causes the higher temperature core fuel being leaked into the water pool below reactor vessel. During the melt-water mixing interaction process, the high temperature melt evaporates the cool water at an extreme high rate and might induce a steam explosion. A steam explosion could experience first the premixing phase and then the propagation explosion phase. For a propagation calculation, we should know the information about the initial fragmentation time, the total melt mass, premixing region size, initial void fraction and distribution of the melt volume fraction, and so on. All the initial conditions used in this calculation are based on analyses from some simple assumptions and the observation from the experiments. The results show that the most important parameter for the initial condition of this phase is the total mass and its initial distribution. This gives the requirement for a premixing calculation. On the other hand, for higher melt volume fraction case, the fragmentation is strong so that the local pressure can exceed over the EOS maximum pressure of the code, which lead to the incorrect calculation or divergence of the calculation. (Suetake, M.)

Inherent safe fast breeder reactors and actinide burners, metallic fuel

International Nuclear Information System (INIS)

Dorner, S.; Schumacher, G.

1991-04-01

Nuclear power without breeder strategy uses the possibilities for the energy supply only to a small extend compared to the possibilities of fast breeder reactors, which offer an energy supply for thousands of years. Moreover, a fast neutron device offers the opportunity to run an actinide-burner that could improve the situation of waste management. Within this concept metallic fuel could play a key role. The present report shows some important aspects of the concept like the pyrometallic reprocessing, the behaviour of metallic fuel during a core meltdown accident and others. The report should contribute to the discussion of these problems and initialize further work

Variability in properties of grouted Phosphate/Sulfate N-Reactor Waste

International Nuclear Information System (INIS)

Lokken, R.O.; Martin, P.F.C.; Bowen, W.M.; Harty, H.; Treat, R.L.

1987-02-01

A Transportable Grout Facility (TGF) is being constructed at the Hanford site in Washington State to convert various low-level liquid wastes to a grout waste form for onsite disposal. The TGF Project is managed by Rockwell Hanford Operations (Rockwell). Oak Ridge National Laboratory (ORNL) has provided a grout formulation for Phosphate/Sulfate N-Reactor Waste, the first waste stream scheduled for grouting beginning in late 1987. The formulation includes a blend of portland cement, fly ash, attapulgite clay, and an illitic clay. Grout will be produced by mixing the blend with Phosphate/Sulfate N-Reactor Waste. These wastes result from decontamination and ion-exchange regeneration activities at Hanford's N-Reactor. Pacific Northwest Laboratory (PNL) is conducting studies on grouted Phosphate/Sulfate N-Reactor Waste to verify that the grout can be successfully processed and, when hardened, that it will meet all performance and regulatory requirements. As part of these studies, PNL is assessing the variability that may be encountered when processing Phosphate/Sulfate N-Reactor Waste grout. Sources of variability that may affect grout properties include the composition and concentrations of the waste and dry solids, temperature, efficiency of dry solids blending, and dry blend storage time. 13 refs., 20 figs., 9 tabs

Severe accidents in nuclear reactors

International Nuclear Information System (INIS)

Ohai, Dumitru; Dumitrescu, Iulia; Tunaru, Mariana

2004-01-01

The likelihood of accidents leading to core meltdown in nuclear reactors is low. The consequences of such an event are but so severe that developing and implementing of adequate measures for preventing or diminishing the consequences of such events are of paramount importance. The analysis of major accidents requires sophisticated computation codes but necessary are also relevant experiments for checking the accuracy of the predictions and capability of these codes. In this paper an overview of the severe accidents worldwide with definitions, computation codes and relating experiments is presented. The experimental research activity of severe accidents was conducted in INR Pitesti since 2003, when the Institute jointed the SARNET Excellence Network. The INR activity within SARNET consists in studying scenarios of severe accidents by means of ASTEC and RELAP/SCDAP codes and conducting bench-scale experiments

Behavior of a corium jet in high pressure melt ejection from a reactor pressure vessel

International Nuclear Information System (INIS)

Frid, W.E.

1986-01-01

A model has been developed to calculate the expansion and fragmentation of a corium jet, due to the evolution of dissolved gas, during a postulated core meltdown accident. Parametric calculations have been performed for a PWR high pressure accident scenario. Jet breakup occurs within a few jet diameters from the RPV. The diameter of the fragmented jet at the level of the reactor cavity floor is predicted to be 40-130 times the discharge diameter. Particles generated by fragmentation of corium melt are predicted to be in the 30-150 μm size range

Proposed high throughput electrorefining treatment for spent N- Reactor fuel

International Nuclear Information System (INIS)

Gay, E.C.; Miller, W.E.; Laidler, J.J.

1996-01-01

A high-throughput electrorefining process is being adapted to treat spent N-Reactor fuel for ultimate disposal in a geologic repository. Anodic dissolution tests were made with unirradiated N-Reactor fuel to determine the type of fragmentation necessary to provide fuel segments suitable for this process. Based on these tests, a conceptual design was produced of a plant-scale electrorefiner. In this design, the diameter of an electrode assembly is about 1.07 m (42 in.). Three of these assemblies in an electrorefiner would accommodate a 3-metric-ton batch of N-Reactor fuel that would be processed at a rate of 42 kg of uranium per hour

Thermohydraulic status and component behavior in the PWR during the selected meltdown scenario station blackout (SBO); Thermohydraulisches Verhalten und Komponentenverhalten eines DWR bei ausgewaehltem Kernschmelzszenarium infolge Station Blackout (SBO). Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Band, Sebastian; Blaesius, Christoph; Scheuerer, Martina; Steinroetter, Thomas

2017-09-15

The report on the thermohydraulic status and component behavior in the PWR during the selected meltdown scenario station blackout (SBO) includes the following issues: status of science and technology on this topic, analysis of a high-pressure meltdown scenario using ATHLET-CD for a German PWR starting from the initiating event station blackout, three-dimensional computational fluid dynamic (CFD) analyses of the pressurizer coolant loop in a generic German PWR, evaluation of the thermohydraulic steam generator behavior and its effect on the involved primary circuit components.

Cost benefit analysis of reactor safety systems

International Nuclear Information System (INIS)

Maurer, H.A.

1984-01-01

Cost/benefit analysis of reactor safety systems is a possibility appropriate to deal with reactor safety. The Commission of the European Communities supported a study on the cost-benefit or cost effectiveness of safety systems installed in modern PWR nuclear power plants. The following systems and their cooperation in emergency cases were in particular investigated in this study: the containment system (double containment), the leakage exhaust and control system, the annulus release exhaust system and the containment spray system. The benefit of a safety system is defined according to its contribution to the reduction of the radiological consequences for the environment after a LOCA. The analysis is so far performed in two different steps: the emergency core cooling system is considered to function properly, failure of the emergency core cooling system is assumed (with the possible consequence of core melt-down) and the results may demonstrate the evidence that striving for cost-effectiveness can produce a safer end result than the philosophy of safety at any cost. (orig.)

International Reactor Physics Experiment Evaluation (IRPhE) Project. IRPhE Handbook - 2017 edition

International Nuclear Information System (INIS)

2017-01-01

The International Reactor Physics Evaluation (IRPhE) Project was initiated as a pilot in 1999 by the Nuclear Energy Agency (NEA) Nuclear Science Committee (NSC). The project was endorsed as an official activity of the NSC in June 2003. While the NEA co-ordinates and administers the IRPhE Project at the international level, each participating country is responsible for the administration, technical direction and priorities of the project within their respective countries. The information and data included in this handbook are available to NEA member countries, to all contributing countries and to others on a case-by-case basis. The IRPhE Project is patterned after the International Criticality Safety Benchmark Evaluation Project (ICSBEP). It closely co-ordinates with the ICSBEP to avoid duplication of efforts and publication of conflicting information. Some benchmark data are applicable to both nuclear criticality safety and reactor physics technology. Some have already been evaluated and published by the ICSBEP, but have been extended to include other types of measurements in addition to the critical configuration. Through this effort, the IRPhE Project will be able to 1) consolidate and preserve the existing worldwide information base; 2) retrieve lost data; 3) identify areas where more data are needed; 4) draw upon the resources of the international reactor physics community to help fill knowledge gaps; 5) identify discrepancies between calculations and experiments due to deficiencies in reported experimental data, cross-section data, cross-section processing codes and neutronics codes; 6) eliminate a large amount of redundant research and processing of reactor physics experiment data, and 7) improve future experimental planning, execution and reporting. This handbook contains reactor physics benchmark specifications that have been derived from experiments performed at nuclear facilities around the world. The benchmark specifications are intended for use by

The Hanford Site N Reactor buildings task identification and evaluation of historic properties

International Nuclear Information System (INIS)

Stapp, D.C.; Marceau, T.E.

1996-01-01

The New Production Reactor complex at Hanford (hereafter referred to as N Reactor) is proposed to be deactivated, decommissioned, and demolished in the coming years. Recognizing that the Hanford Site has been important to the nation, state, and local community, a task was funded to examine the effects that these activities may have on the historic properties of N Reactor. The objectives of the N Reactor buildings task were to identify potential historic properties at N Reactor, to complete Historic Property Inventory forms for all structures considered eligible and ineligible for listing in the National Register of Historic Places, and to prepare a Memorandum of Agreement that identifies the measures required to mitigate any adverse effects

N Reactor Lessons Learned workshop

International Nuclear Information System (INIS)

Heaberlin, S.W.

1993-07-01

This report describes a workshop designed to introduce participants to a process, or model, for adapting LWR Safety Standards and Analysis Methods for use on rector designs significantly different than LWR. The focus of the workshop is on the ''Lessons Learned'' from the multi-year experience in the operation of N Reactor and the efforts to adapt the safety standards developed for commercial light water reactors to a graphite moderated, water cooled, channel type reactor. It must be recognized that the objective of the workshop is to introduce the participants to the operation of a non-LWR in a LWR regulatory world. The total scope of this topic would take weeks to provide a through overview. The objective of this workshop is to provide an introduction and hopefully establish a means to develop a longer term dialogue for technical exchange. This report provides outline of the workshop, a proposed schedule of the workshop, and a description of the tasks will be required to achieve successful completion of the project

MLR reactor

International Nuclear Information System (INIS)

Ryazantsev, E.P.; Egorenkov, P.M.; Nasonov, V.A.; Smimov, A.M.; Taliev, A.V.; Gromov, B.F.; Kousin, V.V.; Lantsov, M.N.; Radchenko, V.P.; Sharapov, V.N.

1998-01-01

The Material Testing Loop Reactor (MLR) development was commenced in 1991 with the aim of updating and widening Russia's experimental base to validate the selected directions of further progress of the nuclear power industry in Russia and to enhance its reliability and safety. The MLR reactor is the pool-type one. As coolant it applies light water and as side reflector beryllium. The direction of water circulation in the core is upward. The core comprises 30 FA arranged as hexagonal lattice with the 90-95 mm pitch. The central materials channel and six loop channels are sited in the core. The reflector includes up to 11 loop channels. The reactor power is 100 MW. The average power density of the core is 0.4 MW/I (maximal value 1.0 MW/l). The maximum neutron flux density is 7.10 14 n/cm 2 s in the core (E>0.1 MeV), and 5.10 14 n/cm 2 s in the reflector (E<0.625 eV). In 1995 due to the lack of funding the MLR designing was suspended. (author)

Decay Heat Removal in GEN IV Gas-Cooled Fast Reactors

International Nuclear Information System (INIS)

Lap-Yan, C.; Wie, T. Y. C.

2009-01-01

The safety goal of the current designs of advanced high-temperature thermal gas-cooled reactors (HTRs) is that no core meltdown would occur in a depressurization event with a combination of concurrent safety system failures. This study focused on the analysis of passive decay heat removal (DHR) in a GEN IV direct-cycle gas-cooled fast reactor (GFR) which is based on the technology developments of the HTRs. Given the different criteria and design characteristics of the GFR, an approach different from that taken for the HTRs for passive DHR would have to be explored. Different design options based on maintaining core flow were evaluated by performing transient analysis of a depressurization accident using the system code RELAP5-3D. The study also reviewed the conceptual design of autonomous systems for shutdown decay heat removal and recommends that future work in this area should be focused on the potential for Brayton cycle DHRs.

N13 - based reactor coolant pressure boundary leakage system

International Nuclear Information System (INIS)

Dissing, E.; Marbaeck, L.; Sandell, S.; Svansson, L.

1980-05-01

A system for the monitoring of leakage of coolant from the reactor coolant pressure boundary and auxiliary systems to the reactor containment, based on the detection of the N13 content in the atmosphere, has been tested. N13 is produced from the oxyegen of the reactor water via the recoil photon nuclear process H1 + 016 + He4. The generation of N13 is therefore independent of fuel element leakage and of the corrosion product content in the water. In the US AEC regulatory guide 1.45 has a leakage increase of 4 liter/ min been suggested as the response limit. The experiments carried out in Ringhals indicate, that with the accomplishment of minor improvements in the installation, a 4 liter/min leakage to the containment will give rise to a signal with a random error range of +- 0.25 liter/min, 99.7 % confidence level. (author)

What occurred in the reactors

International Nuclear Information System (INIS)

Kudo, Kazuhiko

2013-01-01

Described is what occurred in the reactors of Fukushima Daiichi Nuclear Power Plant at the Tohoku earthquake and tsunami (Mar. 11, 2011) from the aspect of engineering science. The tsunami attacked the Plant 1 hr after the quake. The Plant had reactors in buildings no.1-4 at 10 m height from the normal sea level which was flooded by 1.5-5.5 m high wave. All reactors in no.1-6 in the Plant were the boiling water type, and their core nuclear reactions were stopped within 3 sec due to the first quake by control rods inserted automatically. Reactors in no.1-5 lost their external AC power sources by the breakdown and subsequent submergence (no.1-4) of various equipments and in no.1, 2 and 4, the secondary DC power was then lost by the battery death. Although the isolation condenser started to cool the reactor in no.1 after DC cut, its valve was then kept closed to heat up the reactor, leading to the reaction of heated Zr in the fuel tube and water to yield H 2 which was accumulated in the building: the cause of hydrogen explosion on 12th. The reactor in no.2 had the reactor core isolation cooling system (RCIC) which operated normally for few hrs, then probably stopped to heat up the reactor, resulting in meltdown of the core but no explosion occurred because of the opened door of the blowout panel on the wall by the blast of no.1 explosion. The reactor in no.3 had RCIC and high pressure coolant injection system, but their works stopped to result in the core damage and H 2 accumulation leading to the explosion on 14th. The reactor in no.4 had not been operated because of its periodical annual examination, but was explored on 15th, of which cause was thought to be due to backward flow of H 2 from no.3. Finally, the author discusses about this accident from the industrial aspect of the design of safety level (defense in depth) on international views, and problems and tasks given. (T.T.)

N Reactor thermal plume characterization during Pu-only mode of operation

Energy Technology Data Exchange (ETDEWEB)

Ecker, R.M.; Thompson, F.L.; Whelan, G.

1983-04-01

Pacific Northwest Laboratories (PNL) performed field and modeling studies -from March 1982 through June 1983 to characterize the thermal plume from the N Reactor heated water outfall while the N Reactor operated in the Pu-only mode. Part 1 of this report deals with the field studies conducted to characterize the N Reactor thermal plume while in the Pu-only mode of operation. It includes a description of the study area, a description of field tasks and procedures, and data collection results and discussion. Part 2 describes the computer simulation of the thermal plume under different flow conditions and the calibration of the model used. It includes a description of the computer model and the assumptions on which it is based, a presentation of the input data used in this application, and a discussion of modeling results. Because the field studies were restricted by the NPOES permit variance to the spring months when high Columbia River flows prevail the mathematical modeling of the N Reactor thermal plume while the reactor operates in the Pu-only mode is instrumental in characterizing the plume during low Columbia River flows.

Thermohydraulics in a high-temperature gas-cooled reactor primary loop during early phases of unrestricted core-heatup accidents

International Nuclear Information System (INIS)

Kroeger, P.G.; Colman, J.; Hsu, C.J.

1983-01-01

In High Temperature Gas Cooled Reactor (HTGR) siting considerations, the Unrestricted Core Heatup Accidents (UCHA) are considered as accidents of highest consequence, corresponding to core meltdown accidents in light water reactors. Initiation of such accidents can be, for instance, due to station blackout, resulting in scram and loss of all main loop forced circulation, with none of the core auxiliary cooling system loops being started. The result is a slow but continuing core heatup, extending over days. During the initial phases of such UCHA scenarios, the primary loop remains pressurized, with the system pressure slowly increasing until the relief valve setpoint is reached. The major objectives of the work described here were to determine times to depressurization as well as approximate loop component temperatures up to depressurization

Design of first reactor protection system prototype for C A R E M reactor

International Nuclear Information System (INIS)

Azcona, A; Lorenzo, G.; Maciel, F.; Fittipaldi, A

2006-01-01

In this paper we present the design of a prototype of the C A R E M Reactor Protection System, which is implemented on a basis of the digital platform T E L E P E R M X S.The proposed architecture for the Reactor Protection System (R P S) has 4 redundant trains composed by a complete set of sensors, a data acquisition computer and a processing computer.The information from the 4 processing computers goes into to a two voting units with a two out of four (2004) logic and its outputs are combined by a final actuation logic with a voting scheme of one out of two (1002).The prototype is implemented with a unique train.The train inputs are simulated by an Automatic Testing Unit.The pre-established test case or procedure results are fed back into the A T U.The choice of the digital platform T E L E P E R M X S for the R P S implementation allows versatility in the design stage and permits the prototype expansion due to its modular characteristic and the software tools flexibility [es

N reactor individual risk comparison to quantitative nuclear safety goals

International Nuclear Information System (INIS)

Wang, O.S.; Rainey, T.E.; Zentner, M.D.

1990-01-01

A full-scope level III probabilistic risk assessment (PRA) has been completed for N reactor, a US Department of Energy (DOE) production reactor located on the Hanford Reservation in the state of Washington. Sandia National Laboratories (SNL) provided the technical leadership for this work, using the state-of-the-art NUREG-1150 methodology developed for the US Nuclear Regulatory Commission (NRC). The main objectives of this effort were to assess the risks to the public and to the on-site workers posed by the operation of N reactor, to identify changes to the plant that could reduce the overall risk, and to compare those risks to the proposed NRC and DOE quantitative safety goals. This paper presents the methodology adopted by Westinghouse Hanford Company (WHC) and SNL for individual health risk evaluation, its results, and a comparison to the NRC safety objectives and the DOE nuclear safety guidelines. The N reactor results, are also compared with the five NUREG-1150 nuclear plants. Only internal events are compared here because external events are not yet reported in the current draft NUREG-1150. This is the first full-scope level III PRA study with a detailed quantitative safety goal comparison performed for DOE production reactors

Evaluation of containment failure modes and fission product releases during core meltdown accidents in a BWR with a Mark III containment

International Nuclear Information System (INIS)

Ludewig, H.; Yu, W.S.; Jaung, R.; Pratt, W.T.

1985-01-01

An assessment is described of potential failure modes and fission product releases for a large number of postulated core meltdown accidents in a BWR with a Mark III containment. For this containment design, the most important failure mode was found to be due to hydrogen related phenomena. A one-dimensional lumped parameter computer code has been developed and used to determine the probability of various hydrogen phenomena for a range of postulated core meltdown sequences. Potential containment loads have been estimated and compared against the containment capacity to determine the probability of containment failure. The fission product release assessment began by using the MARCH/CORRAL system of codes with key input parameters varied over a reasonable range. The parameters relate to primary system retention, re-emission, pool scrubbing, and fission product release in-vessel vs ex-vessel. The final step used more mechanistic calculations based on the system of codes recently developed under sponsorship of the Accident Source Term Program Office, NRC, and compares these predictions with the range of releases calculated in the sensitivity study

N Reactor pressure tube 1350 postirradiation examination

International Nuclear Information System (INIS)

Cook, D.J.

1977-01-01

The N Reactor pressure tubes were fabricated from Zircaloy-2 primarily due to the excellent corrosion resistance, low neutron absorption, and high strength properties of this alloy. Irradiation damage mechanisms increase the strength and decrease the ductility of the Zircaloy-2. Irradiation data available at the time the tubes were installed indicated that fast neutron irradiation damage mechanisms would not decrease the ductility to unacceptable levels over the estimated plant life of 25 to 30 years. However, because the tubes are a primary coolant system component and only limited data are available on irradiation effects at high fluences, a Postirradiation Examination (PIE) program was developed to assure that service factors do not compromise pressure tube integrity essential to reactor safety. The PIE program requires that a pressure tube be periodically removed from the reactor for destructive testing. The N Reactor Technical Specifications specify that the frequency of pressure tube removal and examination be based upon the previous PIE test results. Four pressure tubes were examined before tube 1350, and the test results were summarized in individual reports. PIE results on tube 1350 were summarized along with the test results on the previous four tubes in a previous report. The purpose of this report is to present in detail the results on PIE of pressure tube 1350, and, in particular, document the technique by which the fracture toughness of the pressure tube was determined

Estudio de un reactor catalítico para la obtención de gas de síntesis

OpenAIRE

Romero Sayago, Sara Isabel

2016-01-01

Este trabajo se centra en el estudio del proceso de reformado de gas natural con vapor de agua para producir gas de síntesis. Un compuesto, que como su nombre indica, es de gran importancia en la síntesis de muchos productos. En concreto, se estudia el reactor heterogéneo catalítico donde tiene lugar la reacción de reformado. Mediante un programa de simulación de procesos químicos, se optimiza el proceso de reformado para obtener un rendimiento elevado en el reactor con el mínimo consumo e...

How did Fukushima-Dai-ichi core meltdown change the probability of nuclear accidents?

International Nuclear Information System (INIS)

Escobar Rangel, Lina; Leveque, Francois

2012-10-01

How to predict the probability of a nuclear accident using past observations? What increase in probability the Fukushima Dai-ichi event does entail? Many models and approaches can be used to answer these questions. Poisson regression as well as Bayesian updating are good candidates. However, they fail to address these issues properly because the independence assumption in which they are based on is violated. We propose a Poisson Exponentially Weighted Moving Average (PEWMA) based in a state-space time series approach to overcome this critical drawback. We find an increase in the risk of a core meltdown accident for the next year in the world by a factor of ten owing to the new major accident that took place in Japan in 2011. (authors)

Transients in a reactor containment after a HCDA

International Nuclear Information System (INIS)

Ghosh, A.K.

1984-01-01

The consequences of a hypothetical core meltdown accident in a fast reactor is analysed. Shock waves are generated in the surrounding medium after the energy release, which is assumed to be instantaneous and at a point. After discussing the difference in the predicted and experimentally observed peak pressure a semi-empirical approach is taken to arrive at a better estimate. This defines the loading on the containment, which is idealised as a combination of a shell and a plate. To simplify the analysis the shell is assumed to be in plane strain and axial symmetry is assumed for both components. The shell response is evaluated by using elasticity theory. Numerical results are presented for peak overpressure and pressure-time history and dynamic stresses in the containment. (Author) [pt

Auditable Safety Analysis and Final Hazard Classification for the 105-N Reactor Zone and 109-N Steam Generator Zone Facility

International Nuclear Information System (INIS)

Kloster, G.L.

1998-07-01

This document is a graded auditable safety analysis (ASA) and final hazard classification (FHC) for the Reactor/Steam Generator Zone Segment. The Reactor/Steam Generator Zone Segment, part of the N Reactor Complex, that is also known as the Reactor Building and Steam Generator Cells. The installation of the modifications described within to support surveillance and maintenance activities are to be completed by July 1, 1999. The surveillance and maintenance activities addressed within are assumed to continue for the next 15- 20 years, until the initiation of facility D ampersand D (i.e., Interim Safe Storage). The graded ASA in this document is in accordance with EDPI-4.30-01, Rev. 1, Safety Analysis Documentation, (BHI-DE-1) and is consistent with guidance provided by the U.S. Department of Energy. This ASA describes the hazards within the facility and evaluates the adequacy of the measures taken to reduce, control, or mitigate the identified hazards. This document also serves as the FHC for the Reactor/Steam Generator Zone Segment. This FHC is developed through the use of bounding accident analyses that envelope the potential exposures to personnel

Thermodynamic Data to Model the Interaction Between Coolant and Fuel in Gen IV Sodium Cooled Fast Reactors

International Nuclear Information System (INIS)

Dinsdale, Alan; Gisby, John; Davies, Hugh; Konings, Rudy; Benes, Ondrej

2013-06-01

Understanding the behaviour of nuclear fuels in various environments is vital to the design and safe operation of nuclear reactors. While this is true if the reactor is operating within its design specification, it is even more so if accidents occur and the fuel is exposed to unexpected temperatures, pressures or chemical environments. It is clearly hazardous and costly to explore all such scenarios experimentally and therefore it is necessary to undertake modelling where possible using well-grounded theoretical approaches. This paper will show examples of where calculations of chemical and phase equilibria have been applied successfully to the long term storage of nuclear waste, phase formation during core meltdown and prediction of fission product release into the atmosphere. It will also highlight the development of thermodynamic data carried out during the European Metrology Research Project Metrofission required to model the potential interaction between the coolant, nuclear fuel, containment materials and atmosphere of a sodium cooled fast reactor. (authors)

Safety characteristics of small heat producing reactors

International Nuclear Information System (INIS)

Seifritz, W.

1987-10-01

The primary objectives of protection in nuclear power plants are the possibility to shut the reactor down in case of emergency and keep it subcritical in the long run, the existence of a heat sink for post-decay heat removal in order to avoid overheating, let alone core meltdown, and the containment of radioactivity within the barriers designed for this purpose, thus preventing significant activity release. In principle, these objectives can be met in various ways, namely by active, passive or inherent technical safeguards systems. In practice, a mixture of these approaches is employed in almost all cases. What matters in the end is the assessment of the overall concept, not of some outstanding feature. Inherent characteristics are easier to achieve in small reactors. However, also in this case, inherent safety does not mean absolute safety. If inherent safety characteristics were all encompassing, they would have to include self-healing effects. However, inanimate matter is incapable of such self-organization. Consequently, inherent characteristics in nuclear technology by definition should include the increased use of dissipative processes in the thermal part of the plant. (author)

Materials surveillance program for C-E NSSS reactor vessels

International Nuclear Information System (INIS)

Koziol, J.J.

1977-01-01

Irradiation surveillance programs for light water NSSS reactor vessels provide the means by which the utility can assess the extent of neutron-induced changes in the reactor vessel materials. These programs are conducted to verify, by direct measurement, the conservatism in the predicted radiation-induced changes and hence the operational parameters (i.e., heat-up, cooldown, and pressurization rates). In addition, such programs provide assurance that the scheduled adjustments in the operational parameters are made with ample margin for safe operation of the plant. During the past 3 years, several documents have been promulgated establishing the criteria for determining both the initial properties of the reactor vessel materials as well as measurement of changes in these initial properties as a result of irradiation. These documents, ASTM E-185-73, ''Recommended Practice for Surveillance Tests for Nuclear Reactor Vessels,'' and Appendix H to 10 CFR 50, ''Reactor Vessel Material Surveillance Program Requirements,'' are complementary to each other. They are the result of a change in the basic philosophy regarding the design and analysis of reactor vessels. In effect, the empirical ''transition temperature approach,'' which was used for design, was replaced by the ''analytical fracture mechanics approach.'' The implementation of this technique was described in Welding Research Council Bulletin 1975 and Appendix G to ASME Code Section III. Further definition of requirements appears in Appendix G to 10 CFR 50 published in July 1973. It is the intent of this paper to describe (1) a typical materials surveillance program for the reactor vessel of a Combustion Engineering NSSS, and (2) how the results of such programs, as well as experimental programs provide feed-back for improvement of materials to enhance their radiation resistance and thereby further improve the safety and reliability of future plants. (author)

Destruction of the BETA experimental facility for core meltdown experiments in the Karlsruhe Nuclear Research Center on 21 March 1992

International Nuclear Information System (INIS)

Feige, K.D.

1992-01-01

The BETA experiment V 6.2 was intended to yield information on the processes involved in a lateral containment meltdown starting in a concrete wall with external water cooling. The unexpected overpressure that caused the explosion occurred 1896 seconds after the melt had been fed into the crucible, inducing the melt-water interaction. The explosion destroyed only the inner space of the facility. (orig.) [de

The German reactor safety study

International Nuclear Information System (INIS)

Birkhofer, A.

1980-01-01

The most important results of the German risk study of a nuclear power plant equipped with a pressurized water reactor were published in August 1979. The main volume of the study with the approach used and the results elaborated has been available for reference since late 1979. Eight technical volumes contain detailed descriptions and documentations of the investigations carried out. The reference facility used as a basis for the technical plant studies was unit B of the Biblis Nuclear Power Station, a KWU PWR of 3750 MW thermal power. This contribution provides more detailed explanations of the methods and the results of the risk study illustrated by examples. The description refers to accident categories and categories of radioactivity releases, probabilities of specific sequences of accident events, and the damage associated with core meltdown accidents as a function of various types of failure. For purposes of evaluation and application of the results the limits in the basic assumptions of the study are referred to. (orig./HP) [de

Substitution of the old console with a fully computerized one. Major maintenance and enhancements of the ventilation and air conditioning system of the reactor building. Research activities at the TRIGA L.E.N.A. plant in Pavia, Italy

International Nuclear Information System (INIS)

Orvini, E.; Piazzoli, A.; Borio, A.

2008-01-01

The TRIGA Mark II reactor of the University of Pavia was operated in the last two years on a routine basis accomplishing different purposes: - Development of B.N.C.T. for diffused tumours of liver; - Neutron activation analysis in matrix of geochemistry, archaeology and environment interest; - Electron spin resonance (ESR) study of radical processes; - Study of trace elements impact in environmental matrix and human health; - High purity control on electronic samples-microchips; - Fast neutron radiation damage investigation; - Certification of standard reference materials and data quality assurance by neutron activation analysis; - Age evaluation by Ar-K method in geological matrix; - Trace elements determination for provenience studies in archaeology; - Basic experiments on fission of Am-242 layers for the space nuclear engine project; - In field search of explosive using prompt gamma emission induced by neutron capture on nitrates. In the period of time between July 1998 and June 2000 the reactor was operated at full power (i.e. 250 kW) for a total amount of 1375 hours. The total fuel element burn-up was 15.07 MWD. During this period of time two major upgrading activities were planned: the installation of a new Instrumentation and Control System (ICS) for the reactor and the installation of a new Air Conditioning and Filtering System (ACFS) for the reactor building. The new ICS is a microprocessor-based design, incorporating the use of one logarithmic wide range neutron flux monitoring channel (NLW-1000), two current mode neutron monitoring safety channels (NP-1000 and NPP-1000) and a linear multi-range neutron flux monitoring channel (Keithley 485). The ICS configuration was personalized by General Atomic according to the requirements and to the technical prescriptions of the Pavia reactor, especially for what concerns the SCRAM inputs and the detectors architecture. Besides, since one the two safety channels, the NPP-1000, has been developed as an advanced

Application of the new GeN-Foam multi-physics solver to the European sodium fast reactor and verification against available codes - 15226

International Nuclear Information System (INIS)

Fiorina, C.; Mikityuk, K.

2015-01-01

A new multi-physics solver for nuclear reactor analysis, named GeN-Foam (Generalized Nuclear Foam), has been developed by the FAST group at the Paul Scherrer Institut. It is based on OpenFOAM and has been developed for the multi-physics transient analyses of pin-based (e.g., liquid metal Fast Reactors, Light Water Reactors) or homogeneous (e.g., fast spectrum Molten Salt Reactors) nuclear reactors. It includes solutions of coarse or fine mesh thermal-hydraulics, thermal-mechanics and neutron diffusion. In particular, thermal-hydraulics solution can combine on the same mesh both a traditional RANS model and a porous medium model, depending on the desired degree of approximation for each region. In case the active reactor core is modeled as a porous medium, a simple sub-solver computes the sub-scale radial temperature profiles in fuel and cladding. The mesh used for neutronics calculations is deformed according to the displacement field predicted by the thermal-mechanics solver, thus allowing for a direct prediction of expansion-related feedback effects in Fast Reactors. To limit computational requirements, GeN-Foam permits the use of three different unstructured meshes for thermal-hydraulics, thermal-mechanics and neutron diffusion. For the same reason, an adaptive time step is employed. The different equations can be solved altogether or selectively included. In this work, GeN-Foam is applied to the analysis of the European Sodium Fast Reactor (ESFR). In particular, a 3-D model of the ESFR core is set up employing a coarse-mesh porous-medium approach for the thermal-hydraulics. The reactor steady-state and different accidental transients are investigated to offer an overview of GeN-Foam use and capabilities, as well as to preliminarily investigate the impact of a relatively accurate thermal-mechanic treatment on the predicted ESFR behavior. A code-to-code benchmark against the TRACE system code is performed to verify the adequacy of the results provided by the new

International Reactor Physics Experiment Evaluation (IRPhE) Project

International Nuclear Information System (INIS)

2013-01-01

The International Reactor Physics Experiment Evaluation (IRPhE) Project aims to provide the nuclear community with qualified benchmark data sets by collecting reactor physics experimental data from nuclear facilities, worldwide. More specifically the objectives of the expert group are as follows: - maintaining an inventory of the experiments that have been carried out and documented; - archiving the primary documents and data released in computer-readable form; - promoting the use of the format and methods developed and seek to have them adopted as a standard. For those experiments where interest and priority is expressed by member countries or working parties and executive groups within the NEA provide guidance or co-ordination in: - compiling experiments into a standard international agreed format; - verifying the data, to the extent possible, by reviewing original and subsequently revised documentation, and by consulting with the experimenters or individuals who are familiar with the experimenters or the experimental facility; - analysing and interpreting the experiments with current state-of-the-art methods; - publishing electronically the benchmark evaluations. The expert group will: - identify gaps in data and provide guidance on priorities for future experiments; - involve the young generation (Masters and PhD students and young researchers) to find an effective way of transferring know-how in experimental techniques and analysis methods; - provide a tool for improved exploitation of completed experiments for Generation IV reactors; - coordinate closely its work with other NSC experimental work groups in particular the International Criticality Safety Benchmark Evaluation Project (ICSBEP), the Shielding Integral Benchmark Experiment Data Base (SINBAD) and others, e.g. knowledge preservation in fast reactors of the IAEA, the ANS Joint Benchmark Activities; - keep a close link with the working parties on scientific issues of reactor systems (WPRS), the expert

The n-n-bar oscillation experiment at the Pavia reactor

International Nuclear Information System (INIS)

Bressi, G.; Calligarich, E.; Cambiaghi, M.; Dolfini, R.; Gigli, A.; Lanza, A.; Liguori, G.; Piazzoli, A.; Ratti, S.; Torre, P.; Cardarelli, R.; Conversi, M.; De Zorzi, G.; Massa, F.; Santonico, R.; Sebastiani, F.; Zanello, D.; Cesana, A.; Terrani, M.

1986-01-01

The n-n-bar oscillation experiment, presented at the Seventh European Conference of Triga Reactor Users in 1982, has recently entered the data collection phase. The possibility of a neutron-antineutron transition, under particular conditions, is foreseen by some Partial Unified Theory. The aim of the experiment is to detect any transition that should take place or to establish a lower limit for the transition time of at least 10 E7 s. A beam of slow neutrons, after a flight in a pipe, air exhausted and shielded against earth magnetic field, crosses a thin carbon target in which the produced antineutrons annihilate. The annihilation products (charged and neutral pions) are dejected in an apparatus situated all around the target. Due to the relatively low flux available a very large cross section beam (∼ 1 m 2 ) had to be used in order to obtain a neutron intensity adequate to the experimental requirements. This raised several problems concerning radiation protection and shielding, in particular in the detector region. The final experimental set up is described and the results concerning the shielding effectiveness and the intensity of the neutron beam obtained are compared with the values foreseen by computer code calculations. (author)

Determination of the boron content in polyethylene samples using the reactor Orphée

CERN Document Server

Gunsing, F; Aberle, O

2017-01-01

The boron content of two unknown types of polyethylene has been determined relative to a known reference type. Samples of polyethylene, including a known boron-less one, were irradiated with thermal neutrons at the reactor Orphée at Saclay in France. Prompt gamma rays were measured with a CeBr$_3$ detector and the intensity of the 478~keV line from $^{10}${B}(n,$\\alpha_1\\gamma$)$^{7}{Li*} was extracted.

Reactor as furnace and reactor as lamp

International Nuclear Information System (INIS)

Goldanskii, V.I.

1992-01-01

There are presented general characteristics of the following ways of transforming of nuclear energy released in reactors into chemical : ordinary way (i.e. trough the heat, mechanical energy and electricity); chemonuclear synthesis ; use of high-temperature fuel elements (reactor as furnace); use of the mixed nγ-radiation of reactors; use of the radiation loops; radiation - photochemical synthesis (reactor as lamp). Advantage and disadvantages of all above variants are compared. The yield of the primary product of fixation of nitrogen (nitric oxide NO) in reactor with the high-temperature (above ca. 1900degC) fuel elements (reactor-furnace) can exceed W ∼ 200 kg per gram of burned uranium. For the latter variant (reactor-lamp) the yield of chemical products can reach W ∼ 60 kg. per gram of uranium. Such values of W are close to or even strongly exceed the yields of chemical products for other abovementioned variants and - what is particularly important - are not connected to the necessity of archscrupulous removal of radioactive contamination of products. (author)

Fish distribution studies near N Reactor, Summer 1983

Energy Technology Data Exchange (ETDEWEB)

Dauble, D.D.; Page, T.L.

1984-06-01

This report summarizes field studies that were initiated in July 1983 to provide estimates of the relative distribution of late-summer outmigrant juvenile salmonids and juvenile resident fish upstream of the N Reactor 009 Outfall. Chinook salmon are among the fish species most sensitive to thermal effects, and impacts to the juvenile outmigrant populations are of particular concern to state and federal regulatory and fisheries management agencies. Therefore, the distribution studies were conducted from late July through September, a period when high ambient river temperatures and low river flows make these salmonid populations most susceptible to thermal effects. In addition, data were not available on the spatial distribution of outmigrant juvenile chinook salmon in late summer. Information on the relative distribution of resident fish populations was also gathered. Previous studies of midstream distribution of juvenile resident fish were limited to a description of ichthyoplankton populations (Beak Consultants, Inc. 1980 Page et al. 1982), and no data were available on vertical or horizontal distribution of juvenile resident fish species near N Reactor. Relative densities and spatial distribution estimates of juvenile salmonid and resident fish species will be used in conjunction with laboratory thermal effects studies (Neitzel et al. 1984) and with plume characterization studies (Ecker et al. 1983) to assess potential impacts of thermal discharge on fish populations near N Reactor.

On the prediction of the reactor vessel integrity under severe accident loadings (RPVSA)

Energy Technology Data Exchange (ETDEWEB)

Krieg, R. E-mail: maeule@irs.fzk.de; Devos, J.; Caroli, C.; Solomos, G.; Ennis, P.J.; Kalkhof, D

2001-11-01

In order to allow more reliable predictions on the lower head response under core melt-down conditions, the temperature distribution has been analysed including the natural convection in the corium pool. Furthermore, the mechanical models and the failure criteria have been improved based on the RUPTHER and FASTHER experiments where typical temperature gradients are simulated. Lower head local melting as well as corium crust development has been addressed in the CORVIS experiments studying the contact between an alumina/iron thermite and a thick steel plate. The upper head loading by corium impact due to a postulated in-vessel steam explosion has been investigated by the BERDA experiments. Similarity rules were considered such that the results can be directly converted to reactor conditions. Based on these investigations admissible steam explosion energy releases are determined which the upper head can carry. If these limits are not exceeded the reactor containment cannot be endangered by broken head fragments. To provide the necessary basic data, mechanical material tests have been performed.

Experimental investigations of the meltdown phase of UO2-Zircaloy fuel rods under conditions of failure of emergency cooling

International Nuclear Information System (INIS)

Hagen, S.; Mack, A.; Malauschek, H.; Wallenfels, K.

1975-01-01

In the monoxidizing helium atmosphere at 1,850 0 C Zircaloy and UO 2 interact violently. The result is a combined meltdown of pellets and can. This phenomenon appears independent of the velocity of temperature rise. In air the oxid skin splits open at 1,890 0 C and the earlier molten material of the interior begins to flow out. When heating up to more than 2,200 0 C the oxid skin remains solid nevertheless. (orig.) [de

Toward a Mechanistic Source Term in Advanced Reactors: A Review of Past U.S. SFR Incidents, Experiments, and Analyses

Energy Technology Data Exchange (ETDEWEB)

Bucknor, Matthew; Brunett, Acacia J.; Grabaskas, David

2016-04-17

In 2015, as part of a Regulatory Technology Development Plan (RTDP) effort for sodium-cooled fast reactors (SFRs), Argonne National Laboratory investigated the current state of knowledge of source term development for a metal-fueled, pool-type SFR. This paper provides a summary of past domestic metal-fueled SFR incidents and experiments and highlights information relevant to source term estimations that were gathered as part of the RTDP effort. The incidents described in this paper include fuel pin failures at the Sodium Reactor Experiment (SRE) facility in July of 1959, the Fermi I meltdown that occurred in October of 1966, and the repeated melting of a fuel element within an experimental capsule at the Experimental Breeder Reactor II (EBR-II) from November 1967 to May 1968. The experiments described in this paper include the Run-Beyond-Cladding-Breach tests that were performed at EBR-II in 1985 and a series of severe transient overpower tests conducted at the Transient Reactor Test Facility (TREAT) in the mid-1980s.

Comparison of the N Reactor and Ignalina Unit No. 2 Level 1 Probabilistic Safety Assessments

International Nuclear Information System (INIS)

Coles, G.A.; McKay, S.L.

1995-06-01

A multilateral team recently completed a full-scope Level 1 Probabilistic Safety Assessment (PSA) on the Ignalina Unit No. 2 reactor plant in Lithuania. This allows comparison of results to those of the PSA for the U.S. Department of Energy's (DOE) N Reactor. The N Reactor, although unique as a Western design, has similarities to Eastern European and Soviet graphite block reactors

German Light-Water-Reactor Safety-Research Program

International Nuclear Information System (INIS)

Seipel, H.G.; Lummerzheim, D.; Rittig, D.

1977-01-01

The Light-Water-Reactor Safety-Research Program, which is part of the energy program of the Federal Republic of Germany, is presented in this article. The program, for which the Federal Minister of Research and Technology of the Federal Republic of Germany is responsible, is subdivided into the following four main problem areas, which in turn are subdivided into projects: (1) improvement of the operational safety and reliability of systems and components (projects: quality assurance, component safety); (2) analysis of the consequences of accidents (projects: emergency core cooling, containment, external impacts, pressure-vessel failure, core meltdown); (3) analysis of radiation exposure during operation, accident, and decommissioning (project: fission-product transport and radiation exposure); and (4) analysis of the risk created by the operation of nuclear power plants (project: risk and reliability). Various problems, which are included in the above-mentioned projects, are concurrently studied within the Heiss-Dampf Reaktor experiments

Reactor Meltdown: Critical Zone Processes In Siliciclastics Unlikely To Be Directly Transferable To Carbonates

Science.gov (United States)

Gulley, J. D.; Cohen, M. J.; Kramer, M. G.; Martin, J. B.; Graham, W. D.

2013-12-01

Carbonate terrains cover 20% of Earth's ice-free land and are modified through interactions between rocks, water and biota that couple ecosystems processes to weathering reactions within the critical zone. Weathering in carbonate systems differs from the Critical Zone Reactor model developed for siliciclastic systems because reactions in siliciclastic critical zones largely consist of incongruent weathering (e.g., feldspar to secondary clay minerals) that typically occur in the soil zone within a few meters of the land surface. These incongruent reactions create regolith, which is removed by physical transport mechanisms that drive landscape denudation. In contrast, carbonate critical zones are mostly composed of homogeneous and soluble minerals, which dissolve congruently with the weathering products exported in solution, limiting regolith in the soil mantle to small amounts of insoluble residues. These reactions can extend to depths greater than 2 km below the surface. As water at the land surface drains preferentially through vertical joints and horizontal bedding planes of the carbonate critical zones, it is 'charged' with biologically-derived carbon dioxide, which decreases pH, dissolves carbonate rock, and enlarges subsurface flowpaths through feedbacks between flow and dissolution. Caves are extreme end products of this process and are key morphological features of carbonate critical zones. Caves link surface processes to the deep subsurface and serve as efficient delivery agents for oxygen, carbon and nutrients to zones within the critical zone that are deficient in all three, interrupting vertical and horizontal chemical gradients that would exist if caves were not present. We present select data from air and water-filled caves in the upper Floridan aquifer, Florida, USA, that demonstrate how caves, acting as very large preferential flow paths, alter processes in carbonate relative to siliciclastic critical zones. While caves represent an extreme end

Validación de la limpieza del reactor empleado en la preparación de medicamentos

Directory of Open Access Journals (Sweden)

Lisseux Castilla Valentín

2001-04-01

Full Text Available En la actualidad, la validación de los procesos se ha convertido en una imperiosa necesidad de la Industria Médico-Farmacéutica, para garantizar la calidad de sus productos y lograr la comercialización de estos. En esta dirección se comenzaron los trabajos de validación de la limpieza de los equipos y se realizó la validación de la limpieza del reactor SEN, que se utiliza para la preparación de los inyectables. Para lograr este objetivo, se elaboró una metodología de trabajo, se seleccionaron los métodos analíticos más apropiados, se establecieron los criterios de aceptación y se escribió un protocolo de validación, que constituyó la herramienta fundamental de trabajo. Posteriormente se realizó la validación de la limpieza del reactor, y se concluyó que el procedimiento de limpieza, aunque no garantiza total eliminación de los residuos del producto, sí cumple con los criterios de aceptación establecidos.At present, the validation of the processes is an imperative necessity of the Medicopharmaceutical Industry to guarantee the quality of its products and to commercialize them. To this end, the cleaning of the equipment began to be validated and the validation of the cleaning of the SEN reactor that is used for the preparation of injections was carried out. To attain this goal, a working methodology was designed, the most appropiate analytical methods were selected, the acceptance criteria were established and a validation protocol was written that was the fundamental working tool. Later on, the validation of the cleaning of the reactor was made and it was concluded that although the cleaning procedure does not guarantee the total elimination of the residuals of the product, it fulfills the established acceptance criteria.

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

Energy Technology Data Exchange (ETDEWEB)

Wiesel, J R

1969-02-15

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions.

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

International Nuclear Information System (INIS)

Wiesel, J.R.

1969-02-01

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions

Environmental assessment for the deactivation of the N Reactor facilities. Revision 1

International Nuclear Information System (INIS)

1994-11-01

This environmental assessment (EA) provides information for the US Department of Energy (DOE) to decide whether the Proposed Action for the N Reactor facilities warrants a Finding of No Significant Impact or requires the preparation of an environmental impact statement (EIS). The EA describes current conditions at the N Reactor facilities, the need to take action at the facilities, the elements of the Proposed Action and alternatives, and the potential environmental impacts. The N Reactor facilities are currently in a surveillance and maintenance program, and will eventually be decontaminated and decommissioned (D and D). Operation and maintenance of the facilities resulted in conditions that could adversely impact human health or the environment if left as is until final D and D. The Proposed Action would deactivate the facilities to remove the conditions that present a potential threat to human health and the environment and to reduce surveillance and maintenance requirements. The action would include surveillance and maintenance after deactivation. Deactivation would take about three years and would involve about 80 facilities. Surveillance and maintenance would continue until final D and D, which is expected to be complete for all facilities except the N Reactor itself by the year 2018

Loss of coolant accident mitigation for liquid metal cooled space reactors

International Nuclear Information System (INIS)

Georgevich, Vladimir; Best, Frederick; Erdman, Carl

1989-01-01

A loss of coolant accident (LOCA) in a liquid metal-cooled space reactor system has been considered as a possible accident scenario. Development of new concepts that will prevent core damage by LOCA caused elevated temperatures is the primary motivation of this work. Decay heat generated by the fission products in the reactor core following shutdown is sufficiently high to melt the fuel unless energy can be removed from the pins at a sufficiently rapid rate. There are two major reasons that prevent utilization of traditional emergency cooling methods. One is the absence of gravity and the other is the vacuum condition outside the reactor vessel. A concept that overcomes both problems is the Saturated Wick Evaporation Method (SWEM). This method involves placing wicking structures at specific locations in the core to act as energy sinks. One of its properties is the isothermal behaviour of the liquid in the wick. The absorption of energy by the surface at the isothermal temperature will direct the energy into an evaporation process and not in sensible heat addition. The use of this concept enables establishment of isothermal positions within the core. A computer code that evaluates the temperature distribution of the core has been developed and the results show that this design will prevent fuel meltdown. (author)

FORE-2, Thermohydraulics and Space-Independent Reactor Kinetics for Transients

International Nuclear Information System (INIS)

Fox, J.N.; Lawler, B.E.; Butz, H.R.; Heames, T.J.

1984-01-01

1 - Description of problem or function: FORE2 is a coupled thermal hydraulics-point kinetics digital computer code designed to calculate significant reactor parameters under steady-state conditions, or as functions of time during transients. The transients may result from a programmed reactivity insertion or a power change. Variable inlet coolant flow rate and temperature are considered. The code calculates the reactor power, the individual reactivity feedbacks, and the temperature of coolant, cladding, fuel, structure, and additional material for up to seven axial positions in three channel types which represent radial zones of the reactor. The heat of fusion, accompanying fuel melting, the liquid metal voiding reactivity, and the spatial and the time variation of the fuel cladding gap coefficient due to changes in gap size are considered. 2 - Method of solution: FORE2 input consists of property data, geometry, power and flow distribution factors, external time varying functions, experimental coefficients, and termination data. The differential equations for fluid flow, heat transfer, and point neutronics are solved by explicit finite-difference procedures. 3 - Restrictions on the complexity of the problem: Reactor excursions which can be calculated are restricted to those transients in which the reactor is not substantially destroyed. As a general rule, changes in reactor geometry and composition during an excursion are limited to those cases in which the reactivity effects of the changes may be considered as small perturbations of the initial system. Thus, accidents involving large-scale disassembly and bulk meltdown of a core are not covered by FORE2. FORE2 is valid only while the core retains its initial geometry

Surface area considerations for corroding N reactor fuel

International Nuclear Information System (INIS)

Johnson, A.B. Jr.; Pitner, A.L.

1996-06-01

The N Reactor fuel is corroding at sites where the Zircaloy cladding was damaged when the fuel was discharged from the reactor. Corroding areas are clearly visible on the fuel stored in open cans in the K East Basin. There is a need to estimate the area of the corroding uranium to analyze aspects of fuel behavior as it is transitioned. from current wet storage to dry storage. In this report, the factors that contribute to open-quotes trueclose quotes surface area are analyzed in terms of what is currently known about the N Reactor fuel. Using observations from a visual examinations of the fuel in the K East wet storage facility, a value for the corroding geometric area is estimated. Based on observations of corroding uranium and surface roughness values for other metals, a surface roughness factor is also estimated and applied to the corroding K East fuel to provide an estimated open-quotes trueclose quotes surface area. While the estimated area may be modified as additional data become available from fuel characterization studies, the estimate provides a basis to assess effects of exposed uranium metal surfaces on fuel behavior in operations involved in transitioning from wet to dry storage, during shipment and staging, conditioning, and dry interim storage

Reactor containment depressurization and filtration equipment for use in the case of a serious accident

International Nuclear Information System (INIS)

L'Homme, A.

1987-06-01

A study was carried out under the aegis of the OECD into filtered vented containment systems which permit depressurization of the containment and filtration of the effluents released to the environment, in the event of a major accident with a pressurized water reactor (PWR) (or BWR or CANDU type reactors) involving core meltdown, with a view to minimizing the consequences. This paper describes the various systems examined which could possibly be used for this purpose. These comprised the French robust sand filtration system, the Swedish FILTRA system, the vacuum containment and discharge and emergency filtration system used by the CANDU plants of the Ontario-Hydro electricity company in Canada and the BWR pressure-suppression pounds. The positions of the various national authorities regarding incorporation of such systems into nuclear power plants, the design and technical principles underlying the systems, the procedures and criteria for their use and their advantages and disadvantages are examined [fr

Effect of the dietary supplement Meltdown on catecholamine secretion, markers of lipolysis, and metabolic rate in men and women: a randomized, placebo controlled, cross-over study

Directory of Open Access Journals (Sweden)

Fisher-Wellman Kelsey H

2009-08-01

Full Text Available Abstract Background We have recently reported that the dietary supplement Meltdown® increases plasma norepinephrine (NE, epinephrine (EPI, glycerol, free fatty acids (FFA, and metabolic rate in men. However, in that investigation measurements ceased at 90 minutes post ingestion, with values for blood borne variables peaking at this time. It was the purpose of the present investigation to extend the time course of measurement to 6 hours, and to include women within the design to determine if sex differences to treatment exist. Methods Ten men (24 ± 4 yrs and 10 women (22 ± 2 yrs ingested Meltdown® or a placebo, using a randomized, cross-over design with one week separating conditions. Blood samples were collected immediately before supplementation and at one hour intervals through 6 hours post ingestion. A standard meal was provided after the hour 3 collection. Samples were assayed for EPI, NE, glycerol, and FFA. Five minute breath samples were collected at each time for measurement of metabolic rate and substrate utilization. Area under the curve (AUC was calculated. Heart rate and blood pressure were recorded at all times. Data were also analyzed using a 2 (sex × 2 (condition × 7 (time repeated measures analysis of variance, with Tukey post hoc testing. Results No sex × condition interactions were noted for AUC for any variable (p > 0.05. Hence, AUC data are collapsed across men and women. AUC was greater for Meltdown® compared to placebo for EPI (367 ± 58 pg·mL-1·6 hr-1 vs. 183 ± 27 pg·mL-1·6 hr-1; p = 0.01, NE (2345 ± 205 pg·mL-1·6 hr-1 vs. 1659 ± 184 pg·mL-1·6 hr-1; p = 0.02, glycerol (79 ± 8 μg·mL-1·6 hr-1 vs. 59 ± 6 μg·mL-1·6 hr-1; p = 0.03, FFA (2.46 ± 0.64 mmol·L-1·6 hr-1 vs. 1.57 ± 0.42 mmol·L-1·6 hr-1; p = 0.05, and kilocalorie expenditure (439 ± 26 kcal·6 hrs-1 vs. 380 ± 14 kcal·6 hrs-1; p = 0.02. No effect was noted for substrate utilization (p = 0.39. Both systolic and diastolic blood pressure

Zirconium carbide coating for corium experiments related to water-cooled and sodium-cooled reactors

Energy Technology Data Exchange (ETDEWEB)

Plevacova, K. [CEA, DEN, STRI, LMA, Cadarache, 3108 St. Paul lez Durance (France); Journeau, C., E-mail: christophe.journeau@cea.fr [CEA, DEN, STRI, LMA, Cadarache, 3108 St. Paul lez Durance (France); Piluso, P. [CEA, DEN, STRI, LMA, Cadarache, 3108 St. Paul lez Durance (France); Zhdanov, V.; Baklanov, V. [IAE, National Nuclear Centre, Material Structure Investigation Dept., Krasnoarmeiskaya, 10, Kurchatov City (Kazakhstan); Poirier, J. [CEMHTI, 1D, av. de la Recherche Scientifique, 45071 Orleans Cedex 2 (France)

2011-07-01

Since the TMI and Chernobyl accidents the risk of nuclear severe accident is intensively studied for existing and future reactors. In case of a core melt-down accident in a nuclear reactor, a complex melt, called corium, forms. To be able to perform experiments with prototypic corium materials at high temperature, a coating which resists to different corium melts related to Generation I and II Water Reactors and Generation IV sodium fast reactor was researched in our experimental platforms both in IAE NNC in Kazakhstan and in CEA in France. Zirconium carbide was selected as protective coating for graphite crucibles used in our induction furnaces: VCG-135 and VITI. The method of coating application, called reactive wetting, was developed. Zirconium carbide revealed to resist well to the (U{sub x}, Zr{sub y})O{sub 2-z} water reactor corium. It has also the advantage not to bring new elements to this chemical system. The coating was then tested with sodium fast reactor corium melts containing steel or absorbers. Undesirable interactions were observed between the coating and these materials, leading to the carburization of the corium ingots. Concerning the resistance of the coating to oxide melts without ZrO{sub 2}, the zirconium carbide coating keeps its role of protective barrier with UO{sub 2}-Al{sub 2}O{sub 3} below 2000 deg. C but does not resist to a UO{sub 2}-Eu{sub 2}O{sub 3} mixture.

N reactor external events probabilistic risk assessment

International Nuclear Information System (INIS)

Baxter, J.T.

1989-01-01

An external events probabilistic risk assessment of the N Reactor has been completed. The methods used are those currently being proposed for external events analysis in NUREG-1150. Results are presented for the external hazards that survived preliminary screening. They are earthquake, fire, and external flood. Core damage frequencies for these hazards are shown to be comparable to those for commercial pressurized water reactors. Dominant fire sequences are described and related to 10 CFR 50, Appendix R design requirements. Potential remedial measures that reduce fire core damage risk are described including modifications to fire protection systems, procedure changes, and addition of new administrative controls. Dominant seismic sequences are described. The effect of non-safety support system dependencies on seismic risk is presented

Remoción de fósforo de diferentes aguas residuales en reactores aeróbios de lecho fluidizado trifásico con circulación interna

Directory of Open Access Journals (Sweden)

Gleyce Teixeira Correia

2013-01-01

Full Text Available El vertimiento de aguas residuales (AR produce impactos sobre los cuerpos de agua receptores. Nutrientes como P generan implicaciones en los sistemas lénticos pues aceleran los procesos de eutrofización. Se han utilizado diversas tecnologías para la remoción de P de las AR: sistemas de tratamiento físico químico con importantes efectos por adición de productos coagulantes; procesos biológicos basados en alternancia de condiciones anaerobias y aerobias con importantes implicaciones de volumen necesario; sistemas como lagunas de estabilización e irrigación requieren de áreas muy considerables y procesos de postratamiento. Los reactores aerobios de lecho fluidizado con circulación interna (RALFCI son opciones compactas que utilizan gran concentración de biomasa activa que han demostrado su capacidad para remover materia orgánica y N. Para AR domésticas provenientes de la estación de bombeo de Ilha Solteira y para los efluentes de un sistema de recirculación acuícola (SRA de cultivo semi-intensivo de tilapia se evaluó la eficiencia de remoción de P reactivo y P total en tres tipos de RALFCI con diámetro externo de 250 mm y diferentes diámetros de tubo interno (DTI, con dos medios de soporte y diferentes concentraciones en dos de los reactores. Las eficiencias medias de remoción de P reactivo en AR domésticas para un tiempo de retención hidráulica (TRH de 3 horas en el reactor con DTI 125 mm variaron entre 25,6 y 38,4% y en el reactor con DTI 150 mm entre 27,5 y 32,5%; la remoción de P total en el SRA para un TRH de 0,19 h y DTI 100 mm fue de 32,7%.

Impingement studies at the 100-N reactor water intake

International Nuclear Information System (INIS)

Page, T.L.; Neitzel, D.A.; Gray, R.H.

1977-09-01

Fish impingement and traveling screen passage were studied at the 100-N reactor water intake structure, Columbia River mile 380, from late April to August 1977. Species and numbers of fish affected were determined and compared to those at the adjacent Hanford Generating Project (HGP). Fish protection procedures previously developed for HGP were evaluated for application at 100-N

Backflushable filter experience at the N Reactor

International Nuclear Information System (INIS)

Ball, B.; Best, W.T.; Keith, R.C.

1987-01-01

The N Reactor is an 4000 MWt, light-water cooled, graphite-moderated reactor located on the Hanford Site in Washington State. A radwaste pilot plant to process plant effluent was constructed in order to maximize future efficiency when a full size radioactive processing facility is built. The pilot plant's purpose is to vary operational parameters such as filtration and ion exchange on a smaller scale to gather as much data as possible. The input to the pilot plant is radioactive drain lines from the N Reactor. The effluent passes through a backflushable filter and a series of ion exchange columns all scaled down from the future proposed facility. A backflushable filter was selected for this application because of the specific characteristics of the plant effluent and the potential reduced operating costs. The filter performance has been excellent in terms of filtration of the effluent. Typical total suspended solids in the plant effluent range from 1 to 6.1 ppm; the filter reduces this value to less than 0.1 ppm. In addition to outstanding filtration efficiency, the use of a precoat material on the filter has resulted in impressive decontamination factors. The filter has been successful in removing up to 50% of the influent activity. An improved performance of several nuclides over other filtration systems has also been achieved. By varying the composition and amount of precoat material on the filter, substantial reductions in waste volumes (and associated operating and disposal costs) have been demonstrated while maintaining a high degree of removal of both activity and total suspended solids

Development of an attached growth reactor for NH₄-N removal at a drinking water supply system in Kathmandu Valley, Nepal.

Science.gov (United States)

Khanitchaidecha, Wilawan; Shakya, Maneesha; Nakano, Yuichi; Tanaka, Yasuhiro; Kazama, Futaba

2012-01-01

Higher concentrations of ammonium (NH(4)-N) and iron (Fe) than a standard for drinking are typical characteristics of groundwater in the study area. To remove NH(4)-N and Fe, the drinking water supply system in this study consists of a series of treatment units (i.e., aeration and sedimentation, filtration, and chlorination); however, NH(4)-N in treated water is higher than a standard for drinking (i.e., removal efficiency. In accordance with raw groundwater characteristics in the area, effects of low inorganic carbon (IC) and phosphate (PO(4)-P) and high Fe on the removal efficiency were also investigated. The results showed a significant increase in NH(4)-N removal efficiency with reactor length and carrier area. A low IC and PO(4)-P had no effect on NH(4)-N removal, whereas a high Fe decreased the efficiency significantly. The first 550 days operation of a pilot-scale reactor installed in the drinking water supply system showed a gradual increase in the efficiency, reaching to 95-100%, and stability in the performance even with increased flow rate from 210 to 860 L/day. The high efficiency of the present work was indicated because only less than 1 mg of NH(4)-N/L was left over in the treated water.

Brookhaven lecture series No. 227: The Chernobyl accident

International Nuclear Information System (INIS)

Kouts, H.

1986-01-01

This lecture discusses the events leading to, during, and following the Chernobyl Reactor number 4 accident. A description of the light water cooled, graphite moderated reactor, the reactor site conditions leading to meltdown is presented. The emission of radioactive effluents and the biological radiation effects is also discussed. (FI)

EVALUACIÓN Y CARACTERIZACIÓN MINERALÓGICA DEL PROCESO DE BIOOXIDACIÓN EN UN REACTOR CONTINUO DE TANQUE AGITADO

Directory of Open Access Journals (Sweden)

DIANA ARROYAVE G.

2010-01-01

Full Text Available La biooxidación del mineral refractario de oro de la mina El Zancudo (TitiribíAntioquia se realizó en un reactor continuo de tanque agitado usando microorganismos nativos acidófilos compatibles con Acidithiobacillus ferrooxidans y Acidithiobacillus thiooxidans. El reactor se operó inicialmente en discontinuo para alcanzar la máxima concentración de hierro férrico en solución, antes de iniciar el proceso en continuo. La caracterización mineralógica se hizo a muestras recolectadas en discontinuo, estado transitorio y estacionario en continuo, usando Microscopia Electrónica de Barrido (SEM y Difracción de Rayos X (DRX. La caracterización mineralógica mostró una oxidación avanzada de la pirita y arsenopirita en discontinuo y parcial en continuo. Adicionalmente, se encontró la formación de silicatos, jarosita y brushita. Los resultados indican que el sistema alcanzó el estado estacionario después de 8 días de operación en continuo, logrando una concentración de hierro férrico en solución de 8.3 g/l, correspondiente a un porcentaje de extracción de oro y plata de 78 y 80 %, respectivamente.

N-reactor charge-discharge system analysis

International Nuclear Information System (INIS)

Tokarz, R.D.; Marr, G.D.; Nesbitt, J.F.

1982-09-01

This report documents an analysis of the existing systems in the N-Reactor fuel flow path. It recommends equipment improvements and changes in that path to allow the charge-discharge rates to be increased to 500 tubes per outage without increasing reactor outage time. The estimated program cost of $14 million is projected over an estimated 3-year period. It does not include costs detailed as part of the existing restoration program or any costs that are considered as normal maintenance. The recommendations contained in this report provide a direction and goal for every critical aspect of the fuel flow path. The way in which these recommendations are implemented may greatly affect the schedule and costs. Previous studies by UNC have shown that enhanced fuel element handling has the potential of increasing productivity by 33 days at a cost benefit estimated at $18 million per year. Enhanced fuel handling provides the greatest potential for productivity improvement of any of the areas considered in these studies

A fuel management study and cycle nuclear design for PW reactors

International Nuclear Information System (INIS)

Minguez, E.; Ahnert, C.; Aragones, J. M.; Corella, M. R.

1975-01-01

A reference reactor was chosen to do a general study involving Fuel Management Evaluations of several cycles, and Design Calculations of cycles already performed, according to a calculation scheme set up in the Reactor Technology Division of the J.E.N., using some computer codes acquired to foreign sources and other ones developed in the J.E.N. (Author) 5 refs

A fuel management study and cycle nuclear design for PW reactors

Energy Technology Data Exchange (ETDEWEB)

Minguez, E; Ahnert, C; Aragones, J M; Corella, M R

1975-07-01

A reference reactor was chosen to do a general study involving Fuel Management Evaluations of several cycles, and Design Calculations of cycles already performed, according to a calculation scheme set up in the Reactor Technology Division of the J.E.N., using some computer codes acquired to foreign sources and other ones developed in the J.E.N. (Author) 5 refs.

Simulation of inlet and outlet riser break sequences in the N Reactor

International Nuclear Information System (INIS)

Bolander, M.A.; Fletcher, C.D.

1988-02-01

This report documents work performed at the Idaho National Engineering Laboratory (INEL) in support of the Westinghouse Hanford Company safety analyses of the N Reactor. The RELAP5/MOD2 computer code was used in analyzing two hypothetical transients. The computer code was modified specifically to simulate the refill behavior in the N Reactor process tubes. The transients analyzed were a double-ended rupture of an inlet riser column and a double-ended rupture of an outlet riser column

E-SCAPE: A scale facility for liquid-metal, pool-type reactor thermal hydraulic investigations

Energy Technology Data Exchange (ETDEWEB)

Van Tichelen, Katrien, E-mail: kvtichel@sckcen.be [SCK-CEN, Boeretang 200, 2400 Mol (Belgium); Mirelli, Fabio, E-mail: fmirelli@sckcen.be [SCK-CEN, Boeretang 200, 2400 Mol (Belgium); Greco, Matteo, E-mail: mgreco@sckcen.be [SCK-CEN, Boeretang 200, 2400 Mol (Belgium); Viviani, Giorgia, E-mail: giorgiaviviani@gmail.com [University of Pisa, Lungarno Pacinotti 43, 56126 Pisa (Italy)

2015-08-15

Highlights: • The E-SCAPE facility is a thermal hydraulic scale model of the MYRRHA fast reactor. • The focus is on mixing and stratification in liquid-metal pool-type reactors. • Forced convection, natural convection and the transition are investigated. • Extensive instrumentation allows validation of computational models. • System thermal hydraulic and CFD models have been used for facility design. - Abstract: MYRRHA (Multi-purpose hYbrid Research Reactor for High-tech Applications) is a flexible fast-spectrum research reactor under design at SCK·CEN. MYRRHA is a pool-type reactor with lead bismuth eutectic (LBE) as primary coolant. The proper understanding of the thermal hydraulic phenomena occurring in the reactor pool is an important issue in the design and licensing of the MYRRHA system and liquid-metal cooled reactors by extension. Model experiments are necessary for understanding the physics, for validating experimental tools and to qualify the design for the licensing. The E-SCAPE (European SCAled Pool Experiment) facility at SCK·CEN is a thermal hydraulic 1/6-scale model of the MYRRHA reactor, with an electrical core simulator, cooled by LBE. It provides experimental feedback to the designers on the forced and natural circulation flow patterns. Moreover, it enables to validate the computational methods for their use with LBE. The paper will elaborate on the design of the E-SCAPE facility and its main parameters. Also the experimental matrix and the pre-test analysis using computational fluid dynamics (CFD) and system thermal hydraulics codes will be described.

Sensitivity analysis of thermal hydraulic response in containment at core meltdown accident

International Nuclear Information System (INIS)

Kobayashi, Kensuke; Ishigami, Tsutomu; Horii, Hideo; Chiba, Takemi.

1985-01-01

A sensitivity analysis of thermal hydraulic response in a containment during a 'station blackout' (the loss of all AC power) accident at Browns Ferry unit one plant was performed with the computer code MARCH 1.0. In the analysis, the plant station batteries were assumed to be available for 4h after the initiation of the accident. The thermal hydraulic response in the containment was calculated by varying several input data for MARCH 1.0 independently and the deviation among calculated results were investigated. The sensitivity analysis showed that (a) the containment would fail due to the overtemperature without any operator actions for plant recovery, which would be strongly dependent on the model of the debris-concrete interaction and the input parameters for specifying the containment failure modes in MARCH 1.0, (b) a core melting temperature and an amount of water left in a primary system at the end of the meltdown were identified as important parameters which influenced the time of the containment failure, and (c) experimental works regarding the parameters mentioned above could be recommended. (author)

Research work for improving LWR safety. 1991 annual report

International Nuclear Information System (INIS)

1992-08-01

The work performed in 1991 for the PNS project centers on various phenomena of severe fuel damage and on selected aspects of a core meltdown accident, relating to aerosol behaviour and filter engineering, and to methods of assessing and minimizing the radiological impacts of a reactor accident. One paper included in this annual report summarizes the evaluation of experiments carried out in 1990 at the Wuerenlingen PROTEUS reactor. The 1991 task programme of the project for the first time included research into extreme load conditions affecting the containment in a core meltdown accident; first results are given of the experiments performed. (orig./DG) [de

Qsub(N) approximation for slowing-down in fast reactors

International Nuclear Information System (INIS)

Rocca-Volmerange, Brigitte.

1976-05-01

An accurate and simple determination of the neutron energy spectra in fast reactors poses several problems. The slowing-down models (Fermi, Wigner, Goertzel-Greuling...) which are different forms of the approximation with order N=0 may prove inaccurate, in spite of recent improvements. A new method of approximation is presented which turns out to be a method of higher order: the Qsub(N) method. It is characterized by a rapid convergence with respect to the order N, by the use of some global parameters to represent the slowing-down and by the expression of the Boltzmann integral equation in a differential formalism. Numerous test verify that, for the order N=2 or 3, the method gives precision equivalent to that of the multigroup numerical integration for the spectra with greatly reduced calculational effort. Furthermore, since the Qsub(N) expressions are a kind of synthesis method, they allow calculation of the spatial Green's function, or the use of collision probabilities to find the flux. Both possibilities have been introduced into existing reactor codes: EXCALIBUR, TRALOR, RE MINEUR... Some applications to multi-zone media (core, blanket, reflector of Masurca pile and exponential slabs) are presented in the isotropic collision approximation. The case of linearly anisotropic collisions is theoretically resolved [fr

Feasibility study of a magnetic fusion production reactor

Science.gov (United States)

Moir, R. W.

1986-12-01

A magnetic fusion reactor can produce 10.8 kg of tritium at a fusion power of only 400 MW —an order of magnitude lower power than that of a fission production reactor. Alternatively, the same fusion reactor can produce 995 kg of plutonium. Either a tokamak or a tandem mirror production plant can be used for this purpose; the cost is estimated at about 1.4 billion (1982 dollars) in either case. (The direct costs are estimated at 1.1 billion.) The production cost is calculated to be 22,000/g for tritium and 260/g for plutonium of quite high purity (1%240Pu). Because of the lack of demonstrated technology, such a plant could not be constructed today without significant risk. However, good progress is being made in fusion technology and, although success in magnetic fusion science and engineering is hard to predict with assurance, it seems possible that the physics basis and much of the needed technology could be demonstrated in facilities now under construction. Most of the remaining technology could be demonstrated in the early 1990s in a fusion test reactor of a few tens of megawatts. If the Magnetic Fusion Energy Program constructs a fusion test reactor of approximately 400 MW of fusion power as a next step in fusion power development, such a facility could be used later as a production reactor in a spinoff application. A construction decision in the late 1980s could result in an operating production reactor in the late 1990s. A magnetic fusion production reactor (MFPR) has four potential advantages over a fission production reactor: (1) no fissile material input is needed; (2) no fissioning exists in the tritium mode and very low fissioning exists in the plutonium mode thus avoiding the meltdown hazard; (3) the cost will probably be lower because of the smaller thermal power required; (4) and no reprocessing plant is needed in the tritium mode. The MFPR also has two disadvantages: (1) it will be more costly to operate because it consumes rather than sells

First evaluation of experimental results describing pressure buildup and hydrogen distribution, obtained by experimental series E11

International Nuclear Information System (INIS)

Holzbauer, H.; Wolf, L.; Valencia, L.

1990-01-01

The beginning of the core meltdown process in the reactor pressure vessel, with a supposed release position for hydrogen in the upper part of the containment, is simulated, and the influence of the plant geometry on the distribution process is studied. In addition, the release point is shifted to the lower containment area, additional hydrogen production owing to the interaction between concrete and melt is taken into account, and sump boiling is simulated. The experimental program covers analytical investigations in the form of blind post-calculations. (DG) [de

Activación del topacio natural irradiado por neutrones en el núcleo del reactor RP-10

OpenAIRE

Gómez, J.; Parreño, Fernando; Lázaro, Gerardo; Vela, Mariano

2003-01-01

Se obtuvieron cristales de topacio activados al ser irradiados con neutrones dentro del núcleo del reactor RP-10. La activación depende del flujo de neutrones, por ello se desarrolló portamuestras (canes de irradiación) para absorber que son los causantes de la activación

Operation experience and maintenance at the TRIGA Mark II L.E.N.A. reactor

International Nuclear Information System (INIS)

Gngoli, F.; Berzero, A.; Lana, F.; Rosti, G.; Meloni, S.

2008-01-01

The TRIGA Mark II reactor of the University of Pavia was operated in the last two years on a routine basis, mostly for neutron activation analysis purposes. Moreover the reactor was completely shutdown in the first six months of this year to allow the dismantling of the NADIR experimental setup. The paper presents: - Reactor operation from July 1990 to June 1992; - Reactor users in the time period January 1990 - December 1991; - Specific activities of some radionuclides in the filling materials; - Specific activity of some radionuclides in thermal column materials. Operations related to dismantling of NADIR experimental facility are described. Finally the new thermal column configuration is presented. Starting from the end inside the reactor tank, a graphite layer (35 cm thick) was positioned, followed by a bismuth layer (10 cm thick) to reduce gamma-ray intensity. The old graphite rods were then positioned leaving in the central part, on the equatorial plane of the thermal column, a cavity whose vertical section has 40 cm width and 20 cm height. The bottom of the cavity, towards to the reactor tank, has been lined with additional layers of graphite (10 cm), bismuth (10 cm) and again graphite (1 cm). The new configuration allowed new experiments to be performed. The cavity in the central part has been created to allow the irradiation of large biological samples such as experimental animal and human livers. This is a peculiar step in a neutron capture boron therapy project to be carried out at the University of Pavia. In order to avoid an implemented 41 Ar production in the void space between shutters and the thermal column outer end, the external surface of the thermal column has been coated with boral sheets. The neutron flux profile, both thermal and epithermal, and cadmium ratio for gold are shown. The flux distribution appears to be adequate to proceed with the neutron capture boron therapy experiment. The LENA Health Physics Service has checked all phases of

CONSTRUCCIÓN DE UN REACTOR DISCONTINUO PARA LA OBTENCIÓN DE BIODIESEL A PARTIR DEL ACEITE DE Ricinus communis

Directory of Open Access Journals (Sweden)

Yolimar Fernández

2014-01-01

Full Text Available Se construyó un reactor discontinuo para obtener biodiesel a partir de 5 litros de extracto obtenido de la semilla de Ricinus communis. El reactor es de acero inoxidable, con longitud de 29 cm; diámetro interno de 15,24 cm y fondo cónico de 20cm de largo, espesor de la pared de 0,2cm, resistencia tubular de 1000 W y motor de 110 volt. Se extrajo y se comparó con las normas respectivas las propiedades físicas y químicas del aceite crudo. Se realizaron pruebas preliminares de transesterificación del aceite catalizadas con NaOH para constatar la viabilidad de la reacción y definir las condiciones operacionales. El biodiesel obtenido fue caracterizado y comparado con referencias presentes en la literatura. Los resultaron mostraron que es posible obtener el biocombustible en el reactor discontinuo con un grado de conversión 88%; confirmando su aplicación en reacciones de transesterificación en medio básico.

Development of a pressurizer level compensator for use on N Reactor

International Nuclear Information System (INIS)

Bussell, J.H.

1985-07-01

The instrument described in this report has been developed to compensate the measured water level in the N Reactor pressurizer for temperature effects. N Reactor is a pressurized water nuclear reactor (PWR). The instrument is defined as a pressurizer level compensator (PLC). A pressurizer is used in a PWR to control the primary coolant pressure and provide a surge volume for primary coolant expansion and contraction. A means of compensating for water and steam density is required because of the wide range of pressure and temperature that result from different steady state and transient reactor power levels. The uncompensated level is determined by measurement of differential pressure between the top of the level measurement zone and the bottom of the level measurement zone. Temperature of the water in the pressurizer is the parameter that is used to determine the proper level compensation since water and steam density are primarily functions of temperature in this case. The PLC uses a microprocessor to calculate the compensated level from temperature and differential pressure measurements. This report includes a description of the design, development, and implementation of software and hardware that are in the PLC. 9 refs., 51 figs., 17 tabs

Technical safety appraisal of the N-Reactor

International Nuclear Information System (INIS)

1986-07-01

This report presents the results of a Technical Safety Appraisal conducted at the Hanford N-Reactor. A team of specialists gathered information for about three weeks on all areas related to safety at the plant. Operational practices, maintenance practices, training drills, and hardware condition were observed. Several recommendations are made in order to correct incomplete rule implementation, to correct hazardous practices, and to promote improvement in satisfactory areas

Environmental assessment for the deactivation of the N Reactor facilities

International Nuclear Information System (INIS)

1995-05-01

This environmental assessment (EA) provides information for the US Department of Energy (DOE) to decide whether the Proposed Action for the N Reactor facilities warrants a Finding of No Significant Impact or requires the preparation of an environmental impact statement (EIS). The EA describes current conditions at the N Reactor facilities, the need to take action at the facilities, the elements of the Proposed Action and alternatives, and the potential environmental impacts. As required by the National Environmental Policy Act of 1969 (NEPA), this EA complies with Title 40, Code of Federal Regulations (CFR), parts 1500--1508, ''Regulations for Implementing the Procedural Provisions of NEPA. '' It also implements the ''National Environmental Policy Act; Implementing Procedures and Guidelines'' (10 CFR 1021)

Color coherent effects in (e,e'N) and (e,e'N,N(h)) processes at CEBAF

International Nuclear Information System (INIS)

Frankfurt, L.L.; Sargsyan, M.M.; Strikman, M.I.

1994-01-01

The options for investigating color coherent effects and competing nuclear effects of nucleon-nucleon correlations in nuclei, nuclear shell effects in (e, e'N) and (e, e'NN(h)) reactions are considered. They argue that extension of CEBAF energies to reach Q 2 = 10 GeV 2 will allow systematical investigations of color coherent effects in nonperturbative regime of QCD and their interplay with nuclear effects

Adaptive Standard Operating Procedures for Complex Disasters

Science.gov (United States)

2017-03-01

Firefighters stuck in Ga . awaiting orders,” Greg Bluestein, Associated Press, September 7, 2005. 77 Sobel and Leeson, “Government’s Response to Hurricane...partial meltdowns in Reactors 2 and 3 as well as gas explosions that devastated several of the containment buildings, leaking radioactive material into... Behaviour in Built Environments,” Proceedings of the 30th eCAADe Conference 1, (2012): 532. 60 autonomous agents, which are capable of interacting with

Analysis of the interim safe storage of reactors at the Hanford site

International Nuclear Information System (INIS)

Wang Hailiang

2014-01-01

The nine production reactors, i.e. B, C, D, DR, F, H, KE, KW and N, at the Hanford site are all water-cooled and graphite-moderated reactors with natural uranium fuel. In 1993, the U.S. Department of Energy (DOE) decided to put eight production reactors (except for B) into Interim Safe Storage (ISS) for 75 years followed by deferred one-piece removal. Reactor B will remain as a national historical landmark. By the end of 2013, six reactors C, F, D, DR, H and N had been successfully put into the ISS. Reactors KE and KW will be put into the ISS in the coming years. Taking reactor C as an example, this paper mainly talks about how to put the production reactors in the Interim Safe Storage, e.g. how to make site preparation, how to construct the safe storage enclosure (SSE) and how to perform surveillance and maintenance during the ISS period, etc. (authors)

Re-assessment of road accident data-analysis policy : applying theory from involuntary, high-consequence, low-probability events like nuclear power plant meltdowns to voluntary, low-consequence, high-probability events like traffic accidents

Science.gov (United States)

2002-02-01

This report examines the literature on involuntary, high-consequence, low-probability (IHL) events like nuclear power plant meltdowns to determine what can be applied to the problem of voluntary, low-consequence high-probability (VLH) events like tra...

Effects of C/N ratio on nitrous oxide production from nitrification in a laboratory-scale biological aerated filter reactor.

Science.gov (United States)

He, Qiang; Zhu, Yinying; Fan, Leilei; Ai, Hainan; Huangfu, Xiaoliu; Chen, Mei

2017-03-01

Emission of nitrous oxide (N 2 O) during biological wastewater treatment is of growing concern. This paper reports findings of the effects of carbon/nitrogen (C/N) ratio on N 2 O production rates in a laboratory-scale biological aerated filter (BAF) reactor, focusing on the biofilm during nitrification. Polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and microelectrode technology were utilized to evaluate the mechanisms associated with N 2 O production during wastewater treatment using BAF. Results indicated that the ability of N 2 O emission in biofilm at C/N ratio of 2 was much stronger than at C/N ratios of 5 and 8. PCR-DGGE analysis showed that the microbial community structures differed completely after the acclimatization at tested C/N ratios (i.e., 2, 5, and 8). Measurements of critical parameters including dissolved oxygen, oxidation reduction potential, NH 4 + -N, NO 3 - -N, and NO 2 - -N also demonstrated that the internal micro-environment of the biofilm benefit N 2 O production. DNA analysis showed that Proteobacteria comprised the majority of the bacteria, which might mainly result in N 2 O emission. Based on these results, C/N ratio is one of the parameters that play an important role in the N 2 O emission from the BAF reactors during nitrification.

Active species in a large volume N2-O2 post-discharge reactor

International Nuclear Information System (INIS)

Kutasi, K; Pintassilgo, C D; Loureiro, J; Coelho, P J

2007-01-01

A large volume post-discharge reactor placed downstream from a flowing N 2 -O 2 microwave discharge is modelled using a three-dimensional hydrodynamic model. The density distributions of the most populated active species present in the reactor-O( 3 P), O 2 (a 1 Δ g ), O 2 (b 1 Σ g + ), NO(X 2 Π), NO(A 2 Σ + ), NO(B 2 Π), NO 2 (X), O 3 , O 2 (X 3 Σ g - ) and N( 4 S)-are calculated and the main source and loss processes for each species are identified for two discharge conditions: (i) p = 2 Torr, f = 2450 MHz, and (ii) p = 8 Torr, f = 915 MHz; in the case of a N 2 -2%O 2 mixture composition and gas flow rate of 2 x 10 3 sccm. The modification of the species relative densities by changing the oxygen percentage in the initial gas mixture composition, in the 0.2%-5% range, are presented. The possible tuning of the species concentrations in the reactor by changing the size of the connecting afterglow tube between the active discharge and the large post-discharge reactor is investigated as well

The 5th surveillance testing for Kori unit 2 reactor vessel materials

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwon Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

2001-03-01

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 5th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Kori unit 2 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules V, R, P, T and N are 2.837E+18, 1.105E+19, 2.110E+19, 3.705E+19 and 4.831E+19n/cm{sup 2}, respectively. The bias factor, the ratio of measurement/calculation, was 0.918 for the 1st through 5th testing and the calculational uncertainty, 11.6% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.898E+19n/cm{sup 2} based on the end of 15th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 4.203E+19, 5.232E+19, 6.262E+19 and 7.291E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Kori unit 2 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 49 refs., 35 figs., 48 tabs. (Author)

Energy-averaged neutron cross sections of fast-reactor structural materials

International Nuclear Information System (INIS)

Smith, A.; McKnight, R.; Smith, D.

1978-02-01

The status of energy-averaged cross sections of fast-reactor structural materials is outlined with emphasis on U.S. data programs in the neutron-energy range 1-10 MeV. Areas of outstanding accomplishment and significant uncertainty are noted with recommendations for future efforts. Attention is primarily given to the main constituents of stainless steel (e.g., Fe, Ni, and Cr) and, secondarily, to alternate structural materials (e.g., V, Ti, Nb, Mo, Zr). Generally, the mass regions of interest are A approximately 50 to 60 and A approximately 90 to 100. Neutron total and elastic-scattering cross sections are discussed with the implication on the non-elastic-cross sections. Cross sections governing discrete-inelastic-neutron-energy transfers are examined in detail. Cross sections for the reactions (n;p), (n;n',p), (n;α), (n;n',α) and (n;2n') are reviewed in the context of fast-reactor performance and/or diagnostics. The primary orientation of the discussion is experimental with some additional attention to the applications of theory, the problems of evaluation and the data sensitivity of representative fast-reactor systems

Dose estimation for nuclear power plant 4 accident in Taiwan at Fukushima nuclear meltdown emission level.

Science.gov (United States)

Tang, Mei-Ling; Tsuang, Ben-Jei; Kuo, Pei-Hsuan

2016-05-01

An advanced Gaussian trajectory dispersion model is used to evaluate the evacuation zone due to a nuclear meltdown at the Nuclear Power Plant 4 (NPP4) in Taiwan, with the same emission level as that occurred at Fukushima nuclear meltdown (FNM) in 2011. Our study demonstrates that a FNM emission level would pollute 9% of the island's land area with annual effective dose ≥50 mSv using the meteorological data on 11 March 2011 in Taiwan. This high dose area is also called permanent evacuation zone (denoted as PEZ). The PEZ as well as the emergency-planning zone (EPZ) are found to be sensitive to meteorological conditions on the event. In a sunny day under the dominated NE wind conditions, the EPZ can be as far as 100 km with the first 7-day dose ≥20 mSv. Three hundred sixty-five daily events using the meteorological data from 11 March 2011 to 9 March 2012 are evaluated. It is found that the mean land area of Taiwan in becoming the PEZ is 11%. Especially, the probabilities of the northern counties/cities (Keelung, New Taipei, Taipei, Taoyuan, Hsinchu City, Hsinchu County and Ilan County) to be PEZs are high, ranging from 15% in Ilan County to 51% in Keelung City. Note that the total population of the above cities/counties is as high as 10 million people. Moreover, the western valleys of the Central Mountain Range are also found to be probable being PEZs, where all of the reservoirs in western Taiwan are located. For example, the probability can be as high as 3% in the far southern-most tip of Taiwan Island in Pingtung County. This shows that the entire populations in western Taiwan can be at risk due to the shortage of clean water sources under an event at FNM emission level, especially during the NE monsoon period. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Jules Horowitz Reactor project, a driver for revival of the research reactor community

International Nuclear Information System (INIS)

Pere, P.; Cavailler, C.; Pascal, C.

2010-01-01

The first concrete of the nuclear island for the Jules Horowitz Reactor (JHR) was poured at the end of July 2009 and construction is ongoing. The JHR is the largest new platform for irradiation experiments supporting Generation II and III reactors, Generation IV technologies, and radioisotope production. This facility, composed of a unique grouping of workshops, hot cells and hot laboratories together with a first-rate MTR research reactor, will ensure that the process, from preparations for irradiation experiments through post-irradiation non-destructive examination, is completed expediently, efficiently and, of course, safely. In addition to the performance requirements to be met in terms of neutron fluxes on the samples (5x10 14 n.cm -2 /sec -1 E>1 MeV in core and 3,6x10 14 n.cm -2 /sec -1 E<0.625 eV in the reflector) and the JHR's considerable irradiation capabilities (more than 20 experiments and one-tenth of irradiation area for simultaneous radioisotope production), the JHR is the first MTR to be built since the end of the 1960s, making this an especially challenging project. The presentation will provide an overview of the reactor, hot cells and laboratories and an outline of the key milestones in the project schedule, including initial criticality in early 2014 and radioisotope production in 2015. This will be followed by a description of the project organization set up by the CEA as owner and future operator and AREVA TA as prime contractor and supplier of critical systems, and a discussion of project challenges, especially those dealing with the following items:accommodation of a broad experimental domain; involvement by international partners making in-kind contributions to the project; ? development of components critical to safety and performance; the revival of engineering of research reactors and experimental devices involving France's historical players in the field of research reactors, and; tools to carry out the project, including computer codes

Analysis of core damage frequency due to external events at the DOE [Department of Energy] N-Reactor

International Nuclear Information System (INIS)

Lambright, J.A.; Bohn, M.P.; Daniel, S.L.; Baxter, J.T.; Johnson, J.J.; Ravindra, M.K.; Hashimoto, P.O.; Mraz, M.J.; Tong, W.H.; Conoscente, J.P.; Brosseau, D.A.

1990-11-01

A complete external events probabilistic risk assessment has been performed for the N-Reactor power plant, making full use of all insights gained during the past ten years' developments in risk assessment methodologies. A detailed screening analysis was performed which showed that all external events had negligible contribution to core damage frequency except fires, seismic events, and external flooding. A limited scope analysis of the external flooding risk indicated that it is not a major risk contributor. Detailed analyses of the fire and seismic risks resulted in total (mean) core damage frequencies of 1.96E-5 and 4.60E-05 per reactor year, respectively. Detailed uncertainty analyses were performed for both fire and seismic risks. These results show that the core damage frequency profile for these events is comparable to that found for existing commercial power plants if proposed fixes are completed as part of the restart program. 108 refs., 85 figs., 80 tabs

Analysis of core damage frequency due to external events at the DOE (Department of Energy) N-Reactor

Energy Technology Data Exchange (ETDEWEB)

Lambright, J.A.; Bohn, M.P.; Daniel, S.L. (Sandia National Labs., Albuquerque, NM (USA)); Baxter, J.T. (Westinghouse Hanford Co., Richland, WA (USA)); Johnson, J.J.; Ravindra, M.K.; Hashimoto, P.O.; Mraz, M.J.; Tong, W.H.; Conoscente, J.P. (EQE, Inc., San Francisco, CA (USA)); Brosseau, D.A. (ERCE, Inc., Albuquerque, NM (USA))

1990-11-01

A complete external events probabilistic risk assessment has been performed for the N-Reactor power plant, making full use of all insights gained during the past ten years' developments in risk assessment methodologies. A detailed screening analysis was performed which showed that all external events had negligible contribution to core damage frequency except fires, seismic events, and external flooding. A limited scope analysis of the external flooding risk indicated that it is not a major risk contributor. Detailed analyses of the fire and seismic risks resulted in total (mean) core damage frequencies of 1.96E-5 and 4.60E-05 per reactor year, respectively. Detailed uncertainty analyses were performed for both fire and seismic risks. These results show that the core damage frequency profile for these events is comparable to that found for existing commercial power plants if proposed fixes are completed as part of the restart program. 108 refs., 85 figs., 80 tabs.

Simulación CFD de la transferencia de calor en un reactor de hidrotratamiento de aceites vegetales de segunda generación

OpenAIRE

Mendoza Sépulveda, César Camilo

2013-01-01

Resumen: Se desarrolló un modelo CFD que permite representar la transferencia de calor en un reactor de hidrotratamiento de aceites vegetales. Este modelo permitió evaluar la transferencia de calor para distintas configuraciones del reactor. En el proceso de hidrotratamiento de aceites vegetales se transforma el aceite en un líquido con cero contenido de azufre y excelentes propiedades como combustible diesel. El proceso se basa en la adición de hidrógeno a alta presión en un reactor de lecho...

N Reactor updated safety analysis report, NUSAR

International Nuclear Information System (INIS)

1978-01-01

An update of the N Reactor safety analysis is presented to reconfirm that the continued operation does not pose undue risk to DOE personnel and property, the public, or the environment. A reanalysis of LOCA and reactivity transients utilizing current codes and methods is made. The principal aspects of the overall submission, a general description, and site characteristics including geography and demography, nearby industrial, transportation and military facilities, meteorology, hydraulic engineering, and geology and seismology are described

Research work for improving LWR safety

International Nuclear Information System (INIS)

Bork, G.

1993-09-01

The work performed in 1992 for the PSF project centers on various phenomena of severe fuel damage and on selected aspects of a core meltdown accident, relating to aerosol behaviour and filter engineering, and to methods of assessing and minimizing the radiological impacts of a reactor accident. The 1992 task programme of the project included research into extreme load conditions affecting the containment in a core meltdown accident: first results are given of the experiments performed. (orig./HP) [de

The modular pebble bed nuclear reactor - the preferred new sustainable energy source for electricity, hydrogen and potable water production?

International Nuclear Information System (INIS)

Kemeny, L.G.

2003-01-01

This paper describes a joint project of Massachusetts Institute of technology, Nu-Tec Inc. and Proto Power. The elegant simplicity of graphite moderated pebble bed reactor is the basis for the 'generation four' nuclear power plants. High Temperature Gas Cooled (HTGC) nuclear power plant have the potential to become the preferred base load sustainable energy source for the new millennium. The great attraction of these helium cooled 'Generation Four' nuclear plant can be summarised as follows: Factory assembly line production; Modularity and ease of delivery to site; High temperature Brayton Cycle ideally suited for cogeneration of electricity, potable water and hydrogen; Capital and operating costs competitive with hydrocarbon plant; Design is inherently meltdown proof and proliferation resistant

COOLOD-N2: a computer code, for the analyses of steady-state thermal-hydraulics in research reactors

International Nuclear Information System (INIS)

Kaminaga, Masanori

1994-03-01

The COOLOD-N2 code provides a capability for the analyses of the steady-state thermal-hydraulics of research reactors. This code is revised version of the COOLOD-N code, and is applicable not only for research reactors in which plate-type fuel is adopted, but also for research reactors in which rod-type fuel is adopted. In the code, subroutines to calculate temperature distribution in rod-type fuel have been newly added to the COOLOD-N code. The COOLOD-N2 code can calculate fuel temperatures under both forced convection cooling mode and natural convection cooling mode as well as COOLOD-N code. In the COOLOD-N2 code, a 'Heat Transfer package' is used for calculating heat transfer coefficient, DNB heat flux etc. The 'Heat Transfer package' is subroutine program and is especially developed for research reactors in which plate-type fuel is adopted. In case of rod-type fuel, DNB heat flux is calculated by both the 'Heat Transfer package' and Lund DNB heat flux correlation which is popular for TRIGA reactor. The COOLOD-N2 code also has a capability of calculating ONB temperature, the heat flux at onset of flow instability as well as DNB heat flux. (author)

Transport of nuclides during a core meltdown accident, with consideration of filtered venting

International Nuclear Information System (INIS)

Haeggblom, H.

1981-01-01

A BWR core meltdown accident has been studied with respect to the transport of radioactive and nonactive gases and aerosols. A system consisting of a containment with an outer stone condenser in three parts was considered. Calculations of the aerosol behaviour have been made with the computer programme NAUA and HAARM-3, assuming one single compartment. Results from these calculations have been used for multicompartment calculations with CORRAL II. The code was modified so that particles of different sizes could be considered in the different compartments, and the time dependence of the particles can be arbitrary. In addition to the aerosol transport and deposition, the corresponding quantities for elemental iodine were calculated. It was concluded, that if the total volume of the condenser system is of the order of 10 5 m 3 , practically all elemental iodine and particles can be retained in the system. The only leakage to the environment will be caused by inefficient sealing during the first five hours. The pressure can never damage the condenser. (author)

A current perspective on the risk significance of steam explosions

International Nuclear Information System (INIS)

Snyder, A.W.

1982-01-01

The view currently held in the Sandia National Laboratory is that, in the case of a meltdown in the reactor core, the probability of a steam explosion is greater than was estimated in WASH-1400, but that the extent and effect of an explosion will be very much smaller than assumed in WASH-1400. This results in a far smaller total risk with regard to containment. In WASH-1400, a nominal conditional probability of 1% was assumed for a containment rupture in a PWR-type reactor, should a large part of the reactor fuel be subject to meltdown during the course of the accident. The German risk analysis study 'Deutsche Risikostudie Kernkraftwerke' dated 1979 considers an explosion of a size sufficient to represent a threat to containment to be considerably more improbable than was assumed in WASH-1400. (orig./DG) [de

Simulación con el código MCNP del reactor nuclear RP-10 en su configuración #14, BOC

OpenAIRE

Lázaro, Gerardo; Parreño, Fernando

2001-01-01

Se presenta los resultados de exceso de reactividad del núcleo del reactor RP-10 en su configuración 14. Este exceso de reactividad ha sido calculado con MCNP4B con un modelo que describe en detalle las características de los elementos combustibles normales y de control, así como de cada elemento que constituye la configuración de trabajo #14. Este modelo fue previamente utilizado en el reactor RP-0 y ha sido aplicado en la configuración de arranque para el cálculo del exceso de reactividad y...

Melt propagation in dry core debris beds

International Nuclear Information System (INIS)

Dosanjh, S.S.

1989-01-01

During severe light water reactor accidents like Three Mile Island Unit 2, the fuel rods can fragment and thus convert the reactor core into a large particle bed. The postdryout meltdown of such debris beds is examined. A two-dimensional model that considers the presence of oxidic (UO 2 and ZrO 2 ) as well as metallic (e.g., zirconium) constituents is developed. Key results are that a dense metallic crust is created near the bottom of the bed as molten materials flow downward and freeze; liquid accumulates above the blockage and, if zirconium is present, the pool grows rapidly as molten zirconium dissolved both UO 2 and ZrO 2 particles; if the melt wets the solid, a fraction of the melt flows radially outward under the action of capillary forces and freezes near the radial boundary; in a nonwetting system, all of the melt flows into the bottom of the bed; and when zirconium and iron are in intimate contact and the zirconium metal atomic fraction is > 0.33, these metals can liquefy and flow out of the bed very early in the meltdown sequence

Damage by radiation in structural materials of BWR reactor vessels; Dano por radiacion en materiales estructurales de vasijas de reactores BWR

Energy Technology Data Exchange (ETDEWEB)

Robles, E.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E. [Departamento de Sintesis y Caracterizacion de Materiales, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2002-07-01

The structural materials which are manufactured the pressure vessels of the BWR reactors undergo degradation in their mechanical properties mainly due to the damage produced by the fast neutrons (E> 1 MeV) coming from the reactor core. The mechanisms of neutron damage in this type of materials are experimentally studied, through the irradiation of vessel steel in experimental reactors for a quickly ageing. Alternately the neutron damage through steel irradiation with heavy ions is simulated. In this work the first results of the damage induced by irradiation of a similar steel to the vessel of a BWR reactor are shown. The irradiation was performed with fast neutrons (E> 1 MeV, fluence of 1.45 x 10{sup 18} n/cm{sup 2}) in the TRIGA Mark III Salazar reactor and separately with Ni{sup +3} ions in a Tandetrom accelerator (E= 4.8 MeV and an ion flux rank of 0.1 to 53 ions/A{sup 2}). (Author)

Third generation nuclear plants

Science.gov (United States)

Barré, Bertrand

2012-05-01

After the Chernobyl accident, a new generation of Light Water Reactors has been designed and is being built. Third generation nuclear plants are equipped with dedicated systems to insure that if the worst accident were to occur, i.e. total core meltdown, no matter how low the probability of such occurrence, radioactive releases in the environment would be minimal. This article describes the EPR, representative of this "Generation III" and a few of its competitors on the world market.

Procedures of ASME code case N-201 for KALIMER. Reactor internal structures

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Yoo, B.

2001-02-01

The main objective of this report is to describe the design procedure of ASME Boiler and Pressure Vessel Code, Code Case N-201-4, which is an elevated temperature structural design code of the Nuclear reactor internal structures, checking the criteria of stress limit, accumulated inelastic strain and deformation, creep-fatigue damage, and buckling limit. As one of examples, the creep-fatigue damage evaluations are carried out for the KALIMER reactor internal structures of baffle annulus. This report is expected to be very useful in evaluating the structural integrity of the liquid metal reactor operating under an elevated temperature

HISTORICAL AMERICAN ENGINEERING RECORD - IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY, TEST AREA NORTH, HAER NO. ID-33-E

Energy Technology Data Exchange (ETDEWEB)

Susan Stacy; Hollie K. Gilbert

2005-02-01

Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly & Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects included NASA's Systems for Nuclear Auxiliary Power and storage of Three Mile Island meltdown debris. National missions for TAN in reactor research and safety research have expired; demolition of historic TAN buildings is underway.

HISTORICAL AMERICAN ENGINEERING RECORD - IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY, TEST AREA NORTH, HAER NO. ID-33-E

International Nuclear Information System (INIS)

Susan Stacy; Hollie K. Gilbert

2005-01-01

Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly and Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects included NASA's Systems for Nuclear Auxiliary Power and storage of Three Mile Island meltdown debris. National missions for TAN in reactor research and safety research have expired; demolition of historic TAN buildings is underway

Filtered atmospheric venting of light water reactor containments

International Nuclear Information System (INIS)

Hedgran, A.; Ahlstroem, P.E.; Nilsson, L.; Persson, Aa.

1982-11-01

The aim of filtered venting is to improve the function of the reactor containment in connection with very severe accidents. By equipping the containment with a safety valve for pressure relief and allowing the released gases to pass through an effective filter, it should be possible to achieve a considerable protective effect. The work has involved detailed studies of the core meltdown sequence, how the molten core material runs out of the reactor vessel, what effect it has on concrete and other structures and how final cooling of the molten core material takes place. On the basis of previous Swedish studies, the project has chosen to study a filter concept that consists of a gravel bed of large volume. This filter plant shall not only retain the radioactive particles that escape from the containment through the vent line, but shall also condense the accompanying steam. After the government decided in 1981 that Barsebaeck was to be equipped with filtered venting and issued specifications regarding its performance, the project aimed at obtaining results that could be used to design and verify a plant for filtered venting at the Barsebaeck nuclear power station. As far as the other Swedish nuclear power plants at Oskarshamn, Ringhals and Forsmark are concerned, the results are only applicable to a limited extent. Additional studies are required for these nuclear power plants before the value of filtered venting can be assessed. Based on the results of experiments and analyses, the project has made a safety analysis with Barsebaeck as a reference plant in order to study how the introduction of filtered venting affects the safety level at a station. In summary, the venting function appears to entail a not insignificant reduction of risks for boiling water reactors of the Barsebaeck type. For a number of types of such very severe core accident cases, the filter design studied ensures a substantial reduction of the releases. However it has not been possible within the

Photocatalytic reactors for treating water pollution with solar illumination: a simplified analysis for n-steps flow reactors with recirculation

Energy Technology Data Exchange (ETDEWEB)

Sagawe, G.; Bahnemann, D. [Universitaet Hannover (Germany). Institut fuer Technische Chemie; Brandi, R.J.; Cassano, A.E. [INTEC Universidad Nacional del Litoral and CONICET, Sante Fe (Argentina)

2005-09-01

The concentration of dissolved oxygen in water, in equilibrium with atmospheric air (ca. 8 ppm at 20{sup o}C), defines the limits of all practical oxidizing processes for removing pollutants in photocatalytic reactors. To solve this limitation, an alternative approach to that of a continuously aerated reactor is the use of a recirculating system with aeration performed after every cycle at the reactor entering stream. As defined by the nature of a single recirculating step (the need of a reactor operation at a rather low concentration range), this procedure results in a very low photonic efficiency (thus requiring a large photon collecting area and consequently increasing the capital cost). The design engineer will have to resort to a series of several reactors with recirculation. This solution may then lead to a very high Photonic Efficiency for the entire process (i.e., a reduced light harvesting area) at the price of an increase in the required capital cost (due to the larger number of reactors). This paper provides a very simple analysis and analytical expressions that can be used to estimate, for a desired degree of degradation, a trade-off solution between a high number of reactors and a very large surface area to collect the solar photons. (author)

The 4th surveillance testing for Kori unit 3 reactor vessel materials

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwun Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

2000-10-01

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 4th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Kori unit 3 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X and W are 4.983E+18, 1.641E+19, 3.158E+19, and 4.469E+19n/cm{sup 2}, respectively. The bias factor, the ratio of calculation/measurement, was 0.840 for the 1st through 4th testing and the calculational uncertainty, 12% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.362E+19n/cm{sup 2} based on the end of 12th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 3.481E+19, 4.209E+19, 5.144E+19 and 5.974E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Kori unit 3 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 48 refs., 35 figs., 41 tabs. (Author)

Efecto de dos metales pesados, cadmio y níquel, sobre la eficiencia de remoción de carga orgánica de un reactor UASB a escala de laboratorio

Directory of Open Access Journals (Sweden)

Luis Eduardo Forero

2004-01-01

Full Text Available Se realizaron ensayos en tres reactores UASB de tres litros cada uno, a un tiempo de retención hidráulico (TRH de cuatro horas y carga orgánica volumétrica de 4,8 g/L/d. Después de la fase inicial de arranque, tiempo de 4.000 horas para los tres reactores, se procedió a afectarlos de la siguiente forma: el primer reactor fue alimentado con 5 mg/L de cloruro de cadmio en forma continua, el segundo reactor fue alimentado con 10 mg/L de cloruro de níquel en forma continua también, mientras que el tercer reactor no se afectó con sustancia alguna y sirvió como control. La eficiencia de remoción de demanda química de oxígeno (DQO del primer reactor cambió del 60% de la fase de arranque (fase 1 al 18% en la fase afectada con cadmio (fase dos; la eficiencia de remoción de DQO en el reactor dos pasó del 60 al 24% y a su vez para el reactor tres control no hubo cambio significativo en dicha eficiencia. A su vez el reactor uno acumuló el cadmio en el lodo, mientras que el reactor dos no hizo lo propio con el níquel.

Annual meeting on nuclear technology 1982. Technical meeting: Possibilities and effects of serious reactor accidents

International Nuclear Information System (INIS)

1982-01-01

A critical examination of the forecast of a design basis accident, the view of the Sandia National Laboratory on the probability of a steam explosion after a core meltdown accident is comparison with WASH-1400, the possibilities of interactions with the containment structure and fission product release, as well as the influences for the assessment of risk in Germany taken from the analysis of core meltdown accidents are dealt with in these papers. (DG) [de

Transuranium contamination in BWRs after fuel accidents and its impact on decommissioning exposures and costs

Energy Technology Data Exchange (ETDEWEB)

Lundgren, K.

1996-12-01

The theme of the present study is to quantify the amount of transuranium activity in different parts of the plant after various fuel accidents, and which impact such contamination has on radiation exposure and costs for decommissioning the plant. The consequences of four different accident degrees have been treated: Common fuel failures, e.g. in line with recent experiences from Swedish BWRs; Fuel channel obstruction resulting in partial melting of one fuel assembly; Total loss of electric power resulting in partial meltdown of the core, but with primary circuit intact preventing a massive contamination of the containment; A LOCA followed by a core meltdown and melting and penetration of the reactor pressure vessel. The amount of transuranium activity distributed, the form of this activity and the plant contamination are evaluated for these accidents. The costs and exposures have been split up on cleanup activities after the accident and decommissioning. 75 refs.

Transuranium contamination in BWRs after fuel accidents and its impact on decommissioning exposures and costs

International Nuclear Information System (INIS)

Lundgren, K.

1996-12-01

The theme of the present study is to quantify the amount of transuranium activity in different parts of the plant after various fuel accidents, and which impact such contamination has on radiation exposure and costs for decommissioning the plant. The consequences of four different accident degrees have been treated: Common fuel failures, e.g. in line with recent experiences from Swedish BWRs; Fuel channel obstruction resulting in partial melting of one fuel assembly; Total loss of electric power resulting in partial meltdown of the core, but with primary circuit intact preventing a massive contamination of the containment; A LOCA followed by a core meltdown and melting and penetration of the reactor pressure vessel. The amount of transuranium activity distributed, the form of this activity and the plant contamination are evaluated for these accidents. The costs and exposures have been split up on cleanup activities after the accident and decommissioning. 75 refs

HECTR [Hydrogen Event Containment Transient Response] Version 1.5N: A modification of HECTR Version 1.5 for application to N Reactor

International Nuclear Information System (INIS)

Camp, A.L.; Dingman, S.E.

1987-05-01

This report describes HECTR Version 1.5N, which is a special version of HECTR developed specifically for application to the N Reactor. HECTR is a fast-running, lumped-parameter containment analysis computer program that is most useful for performing parametric studies. The main purpose of HECTR is to analyze nuclear reactor accidents involving the transport and combustion of hydrogen, but HECTR can also function as an experiment analysis tool and can solve a limited set of other types of containment problems. Version 1.5N is a modification of Version 1.5 and includes changes to the spray actuation logic, and models for steam vents, vacuum breakers, and building cross-vents. Thus, all of the key features of the N Reactor confinement can be modeled. HECTR is designed for flexibility and provides for user control of many important parameters, if built-in correlations and default values are not desired

Estudio mecánico e hidrodinámico de un reactor de gasificación de lecho fluidizado.

Directory of Open Access Journals (Sweden)

W. Rosales

2008-01-01

Full Text Available Se realizó una simulación mediante Elementos Finitos y CFD de un prototipo de gasificador experimental a partir de una geometría propuesta. Se abordan aspectos termomecánicos, al calcularse las deformaciones originadas en el equipo, producto de su peso, en las condiciones de emplazamiento y la carga térmica a la que se somete. También se considera el flujo multifásico gas-sólido presente en el lecho fluidizado, se determina el rango de presiones y velocidades de trabajo del dispositivo, y se estudia la evolución del flujo. Para ello se utiliza el modelo de fuerza de arrastre y presión de sólido de Gidaspow, así como los criterios de velocidad mínima de fluidización de Wen & Yu y Kunii & Levenspiel.A Finite Element and CFD simulations were conducted to a prototype of experimental gasifier, starting from a proposed geometry. Thermomechanic aspects are briefed, calculating the reactor deformation, due to its weight and the thermic load. The gas-solid multiphase flow, present on the fluidized bed was also considered, the working range for the pressure and velocity fields were determined and the flow evolution was studied. The drag force and solid pressure models by Gidaspow, and the minimum fluidization velocity criteria, by Wen & Yu and Kunii & Levenspiel were used.

Delayed photoneutrons of the of the Dalat Nuclear Research Reactor

International Nuclear Information System (INIS)

Ngo Quang Huy; Ha Van Thong; Vu Hai Long; Ngo Phu Khang; Nguyen Nhi Dien; Pham Van Lam; Huynh Dong Phuong; Luong Ba Vien; Le Vinh Vinh

1994-01-01

Time spectrum of delayed neutrons of the Dalat nuclear research reactor is measured and analyzed. It corresponds to a shut-down neutron fluxes of about 10 5 /10 8 n/cm 2 /sec after 100 hours continuous reactor operation at steady power level of 500 kW. Data processing of experimental time neutron spectrum gives 16 exponents, of which 10, resulting from photoneutrons due to (γ,n) reactions on beryllium used inside the reactor core, are obtained by using successive exponential stripping fitting method. For the Dalat reactor, the effective delayed photoneutron fraction relative to the total effective delayed neutron fraction is β B e eff =0.49%β eff for a beryllium weight relative to U 235 fuel of m B e/m U = 8.5. This result is acceptable in comparison to those obtained for other Be-U 235 media. (author). 5 refs., 2 figs., 4 tabs

The analysis for inventory of experimental reactor high temperature gas reactor type

International Nuclear Information System (INIS)

Sri Kuntjoro; Pande Made Udiyani

2016-01-01

Relating to the plan of the National Nuclear Energy Agency (BATAN) to operate an experimental reactor of High Temperature Gas Reactors type (RGTT), it is necessary to reactor safety analysis, especially with regard to environmental issues. Analysis of the distribution of radionuclides from the reactor into the environment in normal or abnormal operating conditions starting with the estimated reactor inventory based on the type, power, and operation of the reactor. The purpose of research is to analyze inventory terrace for Experimental Power Reactor design (RDE) high temperature gas reactor type power 10 MWt, 20 MWt and 30 MWt. Analyses were performed using ORIGEN2 computer code with high temperatures cross-section library. Calculation begins with making modifications to some parameter of cross-section library based on the core average temperature of 570 °C and continued with calculations of reactor inventory due to RDE 10 MWt reactor power. The main parameters of the reactor 10 MWt RDE used in the calculation of the main parameters of the reactor similar to the HTR-10 reactor. After the reactor inventory 10 MWt RDE obtained, a comparison with the results of previous researchers. Based upon the suitability of the results, it make the design for the reactor RDE 20MWEt and 30 MWt to obtain the main parameters of the reactor in the form of the amount of fuel in the pebble bed reactor core, height and diameter of the terrace. Based on the main parameter or reactor obtained perform of calculation to get reactor inventory for RDE 20 MWT and 30 MWT with the same methods as the method of the RDE 10 MWt calculation. The results obtained are the largest inventory of reactor RDE 10 MWt, 20 MWt and 30 MWt sequentially are to Kr group are about 1,00E+15 Bq, 1,20E+16 Bq, 1,70E+16 Bq, for group I are 6,50E+16 Bq, 1,20E+17 Bq, 1,60E+17 Bq and for groups Cs are 2,20E+16 Bq, 2,40E+16 Bq, 2,60E+16 Bq. Reactor inventory will then be used to calculate the reactor source term and it

Development of a system model for advanced small modular reactors.

Energy Technology Data Exchange (ETDEWEB)

Lewis, Tom Goslee,; Holschuh, Thomas Vernon,

2014-01-01

This report describes a system model that can be used to analyze three advance small modular reactor (SMR) designs through their lifetime. Neutronics of these reactor designs were evaluated using Monte Carlo N-Particle eXtended (MCNPX/6). The system models were developed in Matlab and Simulink. A major thrust of this research was the initial scoping analysis of Sandias concept of a long-life fast reactor (LLFR). The inherent characteristic of this conceptual design is to minimize the change in reactivity over the lifetime of the reactor. This allows the reactor to operate substantially longer at full power than traditional light water reactors (LWRs) or other SMR designs (e.g. high temperature gas reactor (HTGR)). The system model has subroutines for lifetime reactor feedback and operation calculations, thermal hydraulic effects, load demand changes and a simplified SCO2 Brayton cycle for power conversion.

Color coherent effects in (e,e{prime}N) and (e,e{prime}N,N(h)) processes at CEBAF

Energy Technology Data Exchange (ETDEWEB)

Frankfurt, L.L.; Sargsyan, M.M. [Tel Aviv Univ. (Israel); Strikman, M.I. [Pennsylvania State Univ., University Park, PA (United States)]|[St. Petersburg Nuclear Physics Inst. (Russian Federation)

1994-04-01

The options for investigating color coherent effects and competing nuclear effects of nucleon-nucleon correlations in nuclei, nuclear shell effects in (e, e{prime}N) and (e, e{prime}NN(h)) reactions are considered. They argue that extension of CEBAF energies to reach Q{sup 2} = 10 GeV{sup 2} will allow systematical investigations of color coherent effects in nonperturbative regime of QCD and their interplay with nuclear effects.

Studies of fragileness in steels of vessels of BWR reactors; Estudios de fragilizacion en aceros de vasija de reactores BWR

Energy Technology Data Exchange (ETDEWEB)

Robles, E.F.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-01

The structural materials with those that are manufactured the pressure vessels of the BWR reactors, suffer degradation in its mechanical properties mainly to the damage taken place by the fast neutrons (E > 1 MeV) coming from the reactor core. Its are experimentally studied those mechanisms of neutron damage in this material type, by means of the irradiation of steel vessel in experimental reactors to age them quickly. Alternatively it is simulated the neutron damage by means of irradiation of steel with heavy ions. In this work those are shown first results of the damage induced by irradiation from a similar steel to the vessel of a BWR reactor. The irradiation was carried out with fast neutrons (E > 1 MeV, fluence of 1.45 x 10{sup 18} n/cm{sup 2}) in the TRIGA MARK lll reactor and separately with Ni{sup +3} ions in a Tandetrom accelerator, E = 4.8 MeV and range of the ionic flow of 0.1 to 53 iones/A{sup 2}. (Author)

Neutron flux measurements in PUSPATI Triga Reactor

International Nuclear Information System (INIS)

Gui Ah Auu; Mohamad Amin Sharifuldin Salleh; Mohamad Ali Sufi.

1983-01-01

Neutron flux measurement in the PUSPATI TRIGA Reactor (PTR) was initiated after its commissioning on 28 June 1982. Initial measured thermal neutron flux at the bottom of the rotary specimen rack (rotating) and in-core pneumatic terminus were 3.81E+11 n/cm 2 sec and 1.10E+12n/cm 2 sec respectively at 100KW. Work to complete the neutron flux data are still going on. The cadmium ratio, thermal and epithermal neutron flux are measured in the reactor core, rotary specimen rack, in-core pneumatic terminus and thermal column. Bare and Cadmium covered gold foils and wires are used for the above measurement. The activities of the irradiated gold foils and wires are determined using Ge(Li) and hyperpure germinium detectors. (author)

The Jules Horowitz reactor project, a driver for revival of the research reactor community

Energy Technology Data Exchange (ETDEWEB)

Pere, P.; Cavailler, C.; Pascal, C. [AREVA TA, CEA Cadarache - Etablissement d' AREVA TA - Chantier RJH - MOE - BV2 - BP no. 9 - 13115 Saint Paul lez Durance (France); CS 50497 - 1100, rue JR Gauthier de la Lauziere, 13593 Aix en Provence cedex 3 (France)

2010-07-01

The first concrete of the nuclear island for the Jules Horowitz Reactor (JHR) was poured at the end of July 2009 and construction is ongoing. The JHR is the largest new platform for irradiation experiments supporting Generation II and III reactors, Generation IV technologies, and radioisotope production. This facility, composed of a unique grouping of workshops, hot cells and hot laboratories together with a first -rate MTR research reactor, will ensure that the process, from preparations for irradiation experiments through post-irradiation non-destructive examination, is completed expediently, efficiently and, of course, safely. In addition to the performance requirements to be met in terms of neutron fluxes on the samples (5x10{sup 14} n.cm{sup -2}/sec{sup -1} E> 1 MeV in core and 3,6x10{sup 14} n.cm{sup -2}/sec{sup -1} E<0.625 eV in the reflector) and the JHR's considerable irradiation capabilities (more than 20 experiments and one-tenth of irradiation area for simultaneous radioisotope production), the JHR is the first MTR to be built since the end of the 1960's, making this an especially challenging project. The presentation will provide an overview of the reactor, hot cells and laboratories and an outline of the key milestones in the project schedule, including initial criticality in early 2014 and radioisotope production in 2015. This will be followed by a description of the project organization set up by the CEA as owner and future operator and AREVA TA as prime contractor and supplier of critical systems, and a discussion of project challenges, especially those dealing with the following items: - accommodation of a broad experimental domain, - involvement by international partners making in-kind contributions to the project, - development of components critical to safety and performance, - the revival of engineering of research reactors and experimental devices involving France's historical players in the field of research reactors, and

k0-measurements and related nuclear data compilation for (n, γ) reactor neutron activation analysis Pt. 3b

International Nuclear Information System (INIS)

Corte, F. de; Simonits, A.

1989-01-01

k 0 -factors and related nuclear data are tabulated for 112 radionuclides of interest in (n, γ) reactor neutron activation analysis. Whenever relevant, critical comments are made with respect to the accuracy of literature data for e. g. isotopic abundances, half-lives, absolute gamma-intensities and 2200 m · s -1 (n, γ) cross sections. As to the latter, a comparison is made with the values calculated from the experimentally determined k 0 -factors, by introduction of selected literature data for the input parameters. References to the table (79 pages) include 156 items. (author) 7 refs.; 1 tab

Prefermentación de agua residual urbana empleando un reactor biopelícula de lecho sumergido

OpenAIRE

Castillo de Castro, Pedro; González Ruiz, Guarocuya; Tejero Monzón, Iñaki

1999-01-01

Esta investigación describe la acidificación de agua residual urbana (ARU). La experimentación se llevó a cabo utilizando un reactor biopelícula de lecho sumergido fijo (BLSF), en el cual se produce la hidrólisis de los sólidos en suspensión retenidos en la zona de decantación del reactor, mientras que la biomasa de la biopelícula se encarga de la acidificación del medio. Se operó bajo cargas orgánicas aplicadas (COA) comprendidas entre 0,5 y 23 kg DQO/m3·d, tiempos de retención hidráulico (T...

REMOCIÓN DE ARSÉNICO ASISTIDA POR OXIDACIÓN UV SOLAR (RAOS EN FOTO-REACTORES TUBULARES DE SECCIÓN SEMICIRCULAR - CINÉTICA DEL CRECIMIENTO DE FLÓCULOS DE Fe(OH3

Directory of Open Access Journals (Sweden)

Ramiro Escalera Vásquez

2012-01-01

Cálculos de capacidad de tratamiento, en régimen continuo (considerando tiempos de residencia hidráulica iguales a los tiempos de irradiación, demuestran la mayor capacidad del foto-reactor de 71 cm de diámetro, logrando un flujo diario de 190 Lm-2 para una operación de 5 h por día. Desde el punto de vista económico y de su construcción, este foto-reactor es más práctico que los reactores de menor diámetro, por la menor cantidad de accesorios y materiales involucrados.

Determination of the lowest critical power levels of the Dalat Nuclear Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Huy, Ngo Quang [Centre for Nuclear Technique Application, Ho Chi Minh City (Viet Nam); Thong, Ha Van; Long, Vu Hai; Binh, Do Quang; Nghiem, Huynh Ton; Tuan, Nguyen Minh; Vien, Luong Ba; Vinh, Le Vinh [Nuclear Research Inst., Da Lat (Viet Nam)

1994-10-01

This paper presents the experimental methods for determining critical states of the Dalat Nuclear Research Reactor containing an extraneous neutron source induced by gamma ray reactions on beryllium in the reactor. The lowest critical power levels are measured at various moments after the reactor is shut down following 100 hours of its continuous operation. Th power levels vary from (0.5-1.2) x 10{sup -4} of P{sub n}, i.e. (25-60)W to (1.1-1.6) x 10{sup -5} of P{sub n}, i.e. (5.5-8)W at corresponding times of 4 days to 13 days after the reactor is shut down. However the critical power must be chosen greater than 500 W to sustain the steady criticality of the reactor for a long time. (author). 3 refs. 4 figs. 1 tab.

Intact and Degraded Component Criticality Calculations of N Reactor Spent Nuclear Fuel

International Nuclear Information System (INIS)

L. Angers

2001-01-01

The objective of this calculation is to perform intact and degraded mode criticality evaluations of the Department of Energy's (DOE) N Reactor Spent Nuclear Fuel codisposed in a 2-Defense High-Level Waste (2-DHLW)/2-Multi-Canister Overpack (MCO) Waste Package (WP) and emplaced in a monitored geologic repository (MGR) (see Attachment I). The scope of this calculation is limited to the determination of the effective neutron multiplication factor (k eff ) for both intact and degraded mode internal configurations of the codisposal waste package. This calculation will support the analysis that will be performed to demonstrate the technical viability for disposing of U-metal (N Reactor) spent nuclear fuel in the potential MGR

Delayed photoneutrons of the of the Dalat Nuclear Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Huy, Ngo Quang [Centre for Nuclear Technique Application, Ho Chi Minh City (Viet Nam); Thong, Ha Van; Long, Vu Hai; Khang, Ngo Phu; Dien, Nguyen Nhi; Lam, Pham Van; Phuong, Huynh Dong; Vien, Luong Ba; Vinh, Le Vinh [Nuclear Research Inst., Da Lat (Viet Nam)

1994-10-01

Time spectrum of delayed neutrons of the Dalat nuclear research reactor is measured and analyzed. It corresponds to a shut-down neutron fluxes of about 10{sup 5}/10{sup 8} n/cm{sup 2}/sec after 100 hours continuous reactor operation at steady power level of 500 kW. Data processing of experimental time neutron spectrum gives 16 exponents, of which 10, resulting from photoneutrons due to ({gamma},n) reactions on beryllium used inside the reactor core, are obtained by using successive exponential stripping fitting method. For the Dalat reactor, the effective delayed photoneutron fraction relative to the total effective delayed neutron fraction is {beta}{sup B}e{sub eff}=0.49%{beta}{sub eff} for a beryllium weight relative to U{sup 235} fuel of m{sub B}e/m{sub U} = 8.5. This result is acceptable in comparison to those obtained for other Be-U{sup 235} media. (author). 5 refs., 2 figs., 4 tabs.

Investigación e investigación formativa

OpenAIRE

Carlos Augusto Hernández

2003-01-01

Este artículo hace una distinción entre investigación e investigación formativa. También señala los peligros de confundir estas dos formas de trabajo académico e insiste en la necesidad de desarrollarlas simultáneamente para enfrentar los nuevos retos de la educación superior. Igualmente habla de la importancia de intensificar los vínculos entre investigación y docencia y hace la diferencia entre investigación pedagógica e investigación formativa. Finalmente cuestiona la posibilidad de una fo...

Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH)

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This guide discusses test procedures that can be used in conjunction with, but not as alternatives to, those required by Practices E185 and E2215 for the surveillance of nuclear reactor vessels. The supplemental mechanical property tests outlined permit the acquisition of additional information on radiation-induced changes in fracture toughness, notch ductility, and yield strength properties of the reactor vessel steels. 1.2 This guide provides recommendations for the preparation of test specimens for irradiation, and identifies special precautions and requirements for reactor surveillance operations and postirradiation test planning. Guidance on data reduction and computational procedures is also given. Reference is made to other ASTM test methods for the physical conduct of specimen tests and for raw data acquisition.

Reactor containment and reactor safety in the United States

International Nuclear Information System (INIS)

Kouts, H.

1986-01-01

The reactor safety systems of two reactors are studied aiming at the reactor containment integrity. The first is a BWR type reactor and is called Peachbottom 2, and the second is a PWR type reactor, and is called surry. (E.G.) [pt

Measurement of 89Y(n,2n) spectral averaged cross section in LR-0 special core reactor spectrum

Science.gov (United States)

Košťál, Michal; Losa, Evžen; Baroň, Petr; Šolc, Jaroslav; Švadlenková, Marie; Koleška, Michal; Mareček, Martin; Uhlíř, Jan

2017-12-01

The present paper describes reaction rate measurement of 89Y(n,2n)88Y in a well-defined reactor spectrum of a special core assembled in the LR-0 reactor and compares this value with results of simulation. The reaction rate is derived from the measurement of activity of 88Y using gamma-ray spectrometry of irradiated Y2O3 sample. The resulting cross section value averaged in spectrum is 43.9 ± 1.5 μb, averaged in the 235U spectrum is 0.172 ± 0.006 mb. This cross-section is important as it is used as high energy neutron monitor and is therefore included in the International Reactor Dosimetry and Fusion File. Calculations of reaction rates were performed with the MCNP6 code using ENDF/B-VII.0, JEFF-3.1, JEFF-3.2, JENDL-3.3, JENDL-4, ROSFOND-2010, CENDL-3.1 and IRDFF nuclear data libraries. The agreement with uranium description by CIELO library is very good, while in ENDF/B-VII.0 description of uranium, underprediction about 10% in average can be observed.

Seismic responses of N-Reactor core. Independent review of Phase II work

International Nuclear Information System (INIS)

Chen, J.C.; Lo, T.; Chinn, D.J.; Murray, R.C.; Johnson, J.J.; Maslenikov, O.R.

1985-08-01

Seismic response of the N-Reactor core was independently analyzed to validate the results of Impell's analysis. The analysis procedure consists of two major stages: linear soil-structure interaction (SSI) analysis of the overall N-Reactor structure complex and nonlinear dynamic analysis of the reactor core. In the SSI analysis, CLASSI computer codes were used to calculate the SSI response of the structures and to generate the input motions for the nonlinear reactor core analysis. In addition, the response was compared to the response from the SASSI analysis under review. The impact of foundation modeling techniques and the effect of soil stiffness variation on SSI response were also investigated. In the core analysis, a nonlinear dynamic analysis model was developed. The stiffness representation of the model was calculated through a finite element analysis of several local core geometries. Finite element analyses were also used to study the block to block interaction characteristics. Using this nonlinear dynamic model along with the basemat time histories generated from CLASSI and SASSI, several dynamic analyses of the core were performed. A series of sensitivity studies was performed to investigate the discretization of the core, the effect of vertical acceleration, the effect of basemat rocking, and modeling assumptions. In general, our independent analysis of core response validates the order of magnitude of the displacement calculated by Impell. 11 refs., 110 figs., 12 tabs

Licensing of MAPLE reactors in Canada

International Nuclear Information System (INIS)

Lee, A.G.; Labrie, J.P.; Langman, V.J.

1999-01-01

Full text: The Operating Licence for a MAPLE reactor (i.e., a 10 MW(th), pool-type reactor), has been approved by the Atomic Energy Control Board (AECB) on August 16th, 1999. This Operating Licence has been obtained within three years of the initiation of the MDS Nordion Medical Isotopes Reactor (MMIR) project, which entails the design, construction and commissioning of two 10 MW MAPLE reactors at AECL's Chalk River Laboratories. The scope and nature of the information required by the AECB, the licensing process and highlights of the events which led to successfully obtaining the Operating Licence for the MAPLE reactor are discussed. These discussions address all phases of the licensing process (i.e., the environmental assessment in support of siting, the Preliminary Safety Analysis Report, PSAR, in support of design, procurement and construction, the Final Safety Analysis Report, FSAR, in support of commissioning and operations, and the development of suitable quality assurance subprograms for each phase). An overview of some of the unique technical aspects associated with the MAPLE reactors, and how they have been addressed during the licensing process are also provided (e.g., applying CSA N285.0, General Requirements for Pressure-Retaining Systems and Components in CANDU Nuclear Power Plants, to a small, low pressure, low temperature research reactor, confirmation of the performance of the driver fuel via laboratory and/or in-reactor testing, validation of the computer codes used to perform the safety analyses, critical parameter uncertainty assessment, full scale hydraulic testing of the performance of the design, fuel handling, human factors validation, operator training and certification). (author)

Damage by radiation in structural materials of BWR reactor vessels

International Nuclear Information System (INIS)

Robles, E.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E.

2002-01-01

The structural materials which are manufactured the pressure vessels of the BWR reactors undergo degradation in their mechanical properties mainly due to the damage produced by the fast neutrons (E> 1 MeV) coming from the reactor core. The mechanisms of neutron damage in this type of materials are experimentally studied, through the irradiation of vessel steel in experimental reactors for a quickly ageing. Alternately the neutron damage through steel irradiation with heavy ions is simulated. In this work the first results of the damage induced by irradiation of a similar steel to the vessel of a BWR reactor are shown. The irradiation was performed with fast neutrons (E> 1 MeV, fluence of 1.45 x 10 18 n/cm 2 ) in the TRIGA Mark III Salazar reactor and separately with Ni +3 ions in a Tandetrom accelerator (E= 4.8 MeV and an ion flux rank of 0.1 to 53 ions/A 2 ). (Author)

Studies of fragileness in steels of vessels of BWR reactors

International Nuclear Information System (INIS)

Robles, E.F.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E.

2003-01-01

The structural materials with those that are manufactured the pressure vessels of the BWR reactors, suffer degradation in its mechanical properties mainly to the damage taken place by the fast neutrons (E > 1 MeV) coming from the reactor core. Its are experimentally studied those mechanisms of neutron damage in this material type, by means of the irradiation of steel vessel in experimental reactors to age them quickly. Alternatively it is simulated the neutron damage by means of irradiation of steel with heavy ions. In this work those are shown first results of the damage induced by irradiation from a similar steel to the vessel of a BWR reactor. The irradiation was carried out with fast neutrons (E > 1 MeV, fluence of 1.45 x 10 18 n/cm 2 ) in the TRIGA MARK lll reactor and separately with Ni +3 ions in a Tandetrom accelerator, E = 4.8 MeV and range of the ionic flow of 0.1 to 53 iones/A 2 . (Author)

Evaluación y estandarización del análisis por activación neutrónica según el método del k-sub cero en el reactor nuclear RP-10: Estudio preliminar empleando irradiaciones cortas

OpenAIRE

Montoya Rossi, Eduardo Haroldo

1995-01-01

Se ha estandarizado una posición de irradiación del reactor nuclear RP-10 para el uso del análisis por activación neutrónica según el método del k sub cero, empleando la convención de Högdahl y se ha evaluado el comportamiento de dicho método respecto a la exactitud y precisión de los resultados obtenidos en el análisis multielemental cuantitativo de diversos materiales certificados de referencia. Para comprobar que el método analítico se encuentra totalmente bajo control estadístico, se ha e...

Preventing another Chernobyl: codes, practices, and the role of new technology

International Nuclear Information System (INIS)

Egan, J.R.

1988-01-01

Preventative steps to prevent and mitigate the consequences of a nuclear accident are considered. The national and international legislation now available is mentioned elsewhere in the book. This chapter discusses the role of codes of conduct and personal agreements which could also prevent nuclear accidents. It is suggested that a radical departure from existing nuclear technology is needed. In particular some definite goals and objectives are suggested. The first is that there should be no meltdowns - all reactors must be physically incapable of core meltdown or explosion under any circumstances. This would mean no huge emergency evacuation plans, no need for expensive emergency core cooling systems. No spiralling cost overruns, no nuclear waste problem, no more huge reactors too big for national electrical systems, no military complications, no intractable decommissionings and no quality control problems are also given as goals. Some of these goals could be achieved with inherently safe reactor designs, much smaller reactors and factory assembly, rather than on-site construction. Other suggestions are also made to achieve the proposed new nuclear technology. (U.K.)

Extension of the GeN-Foam neutronic solver to SP3 analysis and application to the CROCUS experimental reactor

International Nuclear Information System (INIS)

Fiorina, Carlo; Hursin, Mathieu; Pautz, Andreas

2017-01-01

Highlights: • Development and verification of an SP 3 solver based on OpenFOAM. • Integration into the GeN-Foam multi-physics platform. • Application of the new GeN-Foam SP 3 solver to the CROCUS reactor. - Abstract: The Laboratory for Reactor Physics and Systems Behaviour at the PSI and at the EPFL has been developing since 2013 a multi-physics platform for coupled reactor analysis named GeN-Foam. The developed tool includes a solver for the eigenvalue and transient solution of multi-group neutron diffusion equations. Although frequently used in reactor analysis, the diffusion theory shows some limitations for core configurations involving strong anisotropies, which is the case for the CROCUS research reactor at the EPFL. The use of an SP 3 approximation to neutron transport can often lead to visible improvements in a code predictive capabilities, especially for one-directional anisotropies, with acceptable added computational cost vs diffusion. Following some modelling issues for the CROCUS reactor, and in order to improve the GeN-Foam modelling capabilities, the GeN-Foam diffusion solver has been extended to allow for SP 3 analyses. The present paper describes such extension and a preliminary verification using a mini-core PWR benchmark. The newly developed solver is then applied to the analysis of the CROCUS experimental reactor and results are compared to Monte Carlo calculations, as well as to the results of the diffusion solver.

Response of an ESBWR to an accident like Fukushima; Respuesta de un reactor ESBWR a un accidente tipo Fukushima

Energy Technology Data Exchange (ETDEWEB)

Pena G, C. A. [UNAM, Facultad de Ingenieria, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Salazar S, E., E-mail: carlos.pena.guerreo@gmail.com [UNAM, Facultad de Ingenieria, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, 62250 Jiutepec, Morelos (Mexico)

2014-10-15

The Fukushima nuclear accident occurred on March 11, 2011 was caused by an earthquake measuring 9.0 on the seismic scale, damaging the nuclear power plant (NPP) containing 6 nuclear reactors of boiling water, some of whom suffered a meltdown due to failure in the cooling systems of these. Electrical wiring was damaged and emergency diesel generators stopped with the arrival of the tsunami, caused by the earthquake. The presence of many critical systems in flood areas provided that a cascade of technological failures occurred, culminating in the complete loss of control over the central and reactors. This had important political consequences and several countries have revised their nuclear programs, considering dangerous and unworkable to the nuclear energy to meet the specific energy needs of each country. However, progress in the design of new reactors raise the possibility of continuing to use nuclear energy for much safer than before. The NPP of Fukushima contained BWR reactors of the first commercial generation designed in the 50. The new passive safety systems raise the idea of simplifying the systems, lowering costs while they are safer systems. New designs meet a these needs in both BWRs and PWRs. In this paper the response of an ESBWR reactor to similar conditions to those suffered by the reactors of Fukushima NPP during the accident is analyzed. In this new reactor of III + generation, the recirculation pumps are removed and emergency cooling systems that can maintain the stable core for several hours without electricity are used. To analyze the responses of this new reactor the simulator with basic principles that IAEA makes available to from Member States was used to better understand and analyze the performance of this type of reactors. (Author)

Risk Management for Sodium Fast Reactors.

Energy Technology Data Exchange (ETDEWEB)

Denman, Matthew R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Groth, Katrina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cardoni, Jeffrey N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wheeler, Timothy A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-01-01

Accident management is an important component to maintaining risk at acceptable levels for all complex systems, such as nuclear power plants. With the introduction of self - correcting, or inherently safe, reactor designs the focus has shifted from management by operators to allowing the syste m's design to manage the accident. While inherently and passively safe designs are laudable, extreme boundary conditions can interfere with the design attributes which facilitate inherent safety , thus resulting in unanticipated and undesirable end states. This report examines an inherently safe and small sodium fast reactor experiencing a beyond design basis seismic event with the intend of exploring two issues : (1) can human intervention either improve or worsen the potential end states and (2) can a Bayes ian Network be constructed to infer the state of the reactor to inform (1). ACKNOWLEDGEMENTS The author s would like to acknowledge the U.S. Department of E nergy's Office of Nuclear Energy for funding this research through Work Package SR - 14SN100303 under the Advanced Reactor Concepts program. The authors also acknowledge the PRA teams at A rgonne N ational L aborator y , O ak R idge N ational L aborator y , and I daho N ational L aborator y for their continue d contributions to the advanced reactor PRA mission area.

Inclusive (e,e'N), (e,e'NN), (e,e'π),... reactions in nuclei

International Nuclear Information System (INIS)

Gil, A.; Oset, E.

1997-01-01

We study the inclusive (e,e'N), (e,e'NN), (e,e'π), (e,e'πN) reactions in nuclei using a Monte Carlo simulation method to treat the multichannel problem of the final state. The input consists of reaction probabilities for the different steps evaluated using microscopical many body methods. We obtain a good agreement with experiment in some channels where there is data and make predictions for other channels which are presently under investigation in several electron laboratories. The comparison of the theoretical results with experiment for several kinematical conditions and diverse channels can serve to learn about different physical processes occurring in the reaction. The potential of this theoretical tool to make prospections for possible experiments, aiming at pinning down certain reaction probabilities, is also emphasized. (orig.)

FPGA based computation of average neutron flux and e-folding period for start-up range of reactors

International Nuclear Information System (INIS)

Ram, Rajit; Borkar, S.P.; Dixit, M.Y.; Das, Debashis

2013-01-01

Pulse processing instrumentation channels used for reactor applications, play a vital role to ensure nuclear safety in startup range of reactor operation and also during fuel loading and first approach to criticality. These channels are intended for continuous run time computation of equivalent reactor core neutron flux and e-folding period. This paper focuses only the computational part of these instrumentation channels which is implemented in single FPGA using 32-bit floating point arithmetic engine. The computations of average count rate, log of average count rate, log rate and reactor period are done in VHDL using digital circuit realization approach. The computation of average count rate is done using fully adaptive window size moving average method, while Taylor series expansion for logarithms is implemented in FPGA to compute log of count rate, log rate and reactor e-folding period. This paper describes the block diagrams of digital logic realization in FPGA and advantage of fully adaptive window size moving average technique over conventional fixed size moving average technique for pulse processing of reactor instrumentations. (author)

ASTRID core: Design objectives, design approach, and R&D in support

International Nuclear Information System (INIS)

Mignot, G.; Devictor, N.

2012-01-01

ASTRID core design is mainly guided by safety objectives: 1. Prevention of the core meltdown accident: To prevent meltdown accidents: - by a natural behavior of the core and the reactor (no actuation of the two shutdown systems); - with adding passive complementary systems if natural behavior is not sufficient for some transient cases. 2. Mitigation of the fusion accident: To garantee that core fusion accidents don’t lead to significant mechanical energy release, whatever initiator event: - by a natural core behavior; - with adding specific mitigation dispositions in case of natural behavior is not suffficient

Safety of nuclear reactors - Part A - unsteady state temperature history mathematical model

International Nuclear Information System (INIS)

El-Shayeb, M.; Yusoff, M.Z.; Boosroh, M.H.; Ideris, F.; Hasmady Abu Hassan, S.; Bondok, A.

2004-01-01

A nuclear reactor structure under abnormal operations of near meltdown will be exposed to a tremendous amount of heat flux in addition to the stress field applied under normal operation. Temperature encountered in such case is assumed to be beyond 1000 Celsius degrees. A 2-dimensional mathematical model based on finite difference methods, has been developed for the fire resistance calculation of a concrete-filled square steel column with respect to its temperature history. Effects due to nuclear radiation and mechanical vibrations will be explored in a later future model. The temperature rise in each element can be derived from its heat balance by applying the parabolic unsteady state, partial differential equation and numerical solution into the steel region. Calculation of the temperature of the elementary regions needs to satisfy the symmetry conditions and the relevant material properties. The developed mathematical model is capable to predict the temperature history in the column and on the surface with respect to time. (authors)

Neutronics simulations on hypothetical power excursion and possible core melt scenarios in CANDU6

International Nuclear Information System (INIS)

Kim, Yonghee

2015-01-01

LOCA (Loss of coolant accident) is an outstanding safety issue in the CANDU reactor system since the coolant void reactivity is strongly positive. To deal with the LOCA, the CANDU systems are equipped with specially designed quickly-acting secondary shutdown system. Nevertheless, the so-called design-extended conditions are requested to be taken into account in the safety analysis for nuclear reactor systems after the Fukushima accident. As a DEC scenario, the worst accident situation in a CANDU reactor system is a unprotected LOCA, which is supposed to lead to a power excursion and possibly a core melt-down. In this work, the hypothetical unprotected LOCA scenario is simulated in view of the power excursion and fuel temperature changes by using a simplified point-kinetics (PK) model accounting for the fuel temperature change. In the PK model, the core reactivity is assumed to be affected by a large break LOCA and the fuel temperature is simulated to account for the Doppler effect. In addition, unlike the conventional PK simulation, we have also considered the Xe-I model to evaluate the impact of Xe during the LOCA. Also, we tried to simulate the fuel and core melt-down scenario in terms of the reactivity through a series of neutronics calculations for hypothetical core conditions. In case of a power excursion and possible fuel melt-down situation, the reactor system behavior is very uncertain. In this work, we tried to understand the impacts of fuel melt and relocation within the pressure vessel on the core reactivity and failure of pressure and calandria tubes. (author)

Use of research and test reactors for SPD development and calibration

International Nuclear Information System (INIS)

LaFontaine, M.W.R.

2011-01-01

Prior to using a research or test reactor for performance studies or calibration of self powered detectors, it is first necessary to fully characterize the reactor environment in the region to be utilized. This presentation details Characterization Experiments performed to quantify research/test reactor core/site parameters as they would apply for use with SPD applications. Methods will be described to: Determine the Westcott parameter, r (T n /T o ) , for the region of interest; Characterize the neutron energy spectrum in terms of the cadmium absorption cut-off, i.e., consider neutrons of energy 5kT 0.13 eV to be epithermal neutrons; Determine T n , the effective neutron temperature, in the region of interest; Determine the gamma flux in the region of interest; and, Establish SPD calibration standard detectors.

Analysis of the danger potential of H2/CO-combustion in the event of core meltdown

International Nuclear Information System (INIS)

Fischer, M.; Wagler, K.; Schwarzott, W.; Reineke, H.H.

1987-01-01

Based on an evaluation of the present state of knowledge and the experiments performed, several computing programs for the simulation of H 2 /CO combustion processes were developed within the scope of this project. Besides the one-compartment-model MOPED, based on the formulation of empirical and phenomenological connections, which was also used later to perform the pressure buildup analyses during various core meltdown (CM) scenarios, these were the first two attempts in respect of a fluid-dynamic description of the combustion processes that also takes the reaction kinetics into account (VERLA code, PISCES code). The analysis of the low (LP) and high (HP) pressure path CM conditions showed that no additional risk arises on the HP path due to potential H 2 combustion. In opposition to this maximum combustion gas fractions of 15% by vol. H 2 and 2.5% by vol. CO with assumption of complete enrichment in the containment result on the LP path. With 37 refs., 3 tabs., 78 figs [de

Peculiarities of approximation for reactor neutron energy spectra during computerized simulation of radiation defects

International Nuclear Information System (INIS)

Kupchishin, A.A.; Kupchishin, A.I.; Stusik, G.; Omarbekova, Zh.

2001-01-01

Peculiarities of approximation for reactor neutron energy spectra during radiation defects computerized simulation were discussed. Approximation of neutron spectra N(E) was carried out by N(E)=α·exp(-β·E)·sh(γ·E) formula (1), where α, β, γ - approximation coefficients. In the capacity of operating reactor data experimental data on 235 U and 239 Pu were applied. The algorithm was designed, and acting soft ware for spectra parameters calculation was developed. The following values of approximation parameters were obtained: α=80.8; β=0.935;γ=2.04 (for uranium and plutonium these coefficients are less distinguishing). Then with use of formula 1 and α, β, γ coefficients the approximation curves were constructed. These curves satisfactorily describe existing experimental data and allowing to use its for radiation defects simulation in the reactor materials

Analysis of recessive sex-linked lethal mutations in genetically different strains of Drosophila melanogaster ms and w irradiated in the five-kilometer zone of the Chernobyl meltdown

International Nuclear Information System (INIS)

Aslanyan, M.M.; Kim, A.I.; Magomedova, M.A.; Fatkulbayanova, N.L.

1994-01-01

The frequency of induced and spontaneous recessive sex-linked lethal mutations (RSLLM) in Drosophila melanogaster strains w and ms was estimated after their chronic irradiation in the five-kilometer zone of the Chernobyl' meltdown. The mutagenic effect of relatively low radiation doses was analyzed. In an experiment conducted in 1990, a significant increase in the RSLLM frequency was recorded, while, in 1991, no significant difference between the experiment and control was found

Neutron capture cross section measurement of $^{238}$U at the n_TOF CERN facility in the energy region from 1 eV to 700 keV

CERN Document Server

Mingrone, F; Vannini, G; Colonna, N; Gunsing, F; Zugec, P; Altstadt, S; Andrzejewski, J; Audouin, L; Barbagallo, M; Becares, V; Becvavr, F; Belloni, F; Berthoumieux, E; Billowes, J; Bosnar, D; Brugger, M; Calviani, M; Calvino, F; Cano-Ott, D; Carrapico, C; Cerutti, F; Chiaveri, E; Chin, M; Cortes, G; Cortes-Giraldo, M A; Diakaki, M; Domingo-Pardo, C; Duran, I; Dressler, R; Eleftheriadis, C; Ferrari, A; Fraval, K; Ganesan, S; Garcia, A R; Giubrone, G; Goncalves, I F; Gonzalez-Romero, E; Griesmayer, E; Guerrero, C; Hernandez-Prieto, A; Jenkins, D G; Jericha, E; Kadi, Y; Kappeler, F; Karadimos, D; Kivel, N; Koehler, P; Kokkoris, M; Krticka, M; Kroll, J; Lampoudis, C; Langer, C; Leal-Cidoncha, E; Lederer, C; Leeb, H; Leong, L S; Lo Meo, S; Losito, R; Mallick, A; Manousos, A; Marganiec, J; Martinez, T; Mastinu, P F; Mastromarco, M; Mendoza, E; Mengoni, A; Milazzo, P M; Mirea Horia, M; Mondalaers, W; Paradela, C; Pavlik, A; Perkowski, J; Plompen, A; Praena, J; Quesada, J M; Rauscher, T; Reifarth, R; Riego, A; Robles, M S; Rubbia, C; Sabate-Gilarte, M; Sarmento, R; Saxena, A; Schillebeeckx, P; Schmidt, S; Schumann, D; Tagliente, G; LTain, J; Tarrio, D; Tassan-Got, L; Tsinganis, A; Valenta, S; Variale, V; Vaz, P; Ventura, A; Vermeulen, M J; Vlachoudis, V; Vlastou, R; Wallner, A; Ware, T; Weigand, M; Weiss, C; Wright, T

2016-01-01

The aim of this work is to provide a precise and accurate measurement of the $^{238}$U(n,$\\gamma$) reaction cross section in the energy region from 1 eV to 700 keV. This reaction is of fundamental importance for the design calculations of nuclear reactors, governing the behaviour of the reactor core. In particular, fast reactors, which are experiencing a growing interest for their ability to burn radioactive waste, operate in the high energy region of the neutron spectrum. In this energy region most recent evaluations disagree due to inconsistencies in the existing measurements of up to 15%. In addition, the assessment of nuclear data uncertainty performed for innovative reactor systems shows that the uncertainty in the radiative capture cross-section of $^{238}$U should be further reduced to 1-3% in the energy region from 20 eV to 25 keV. To this purpose, addressed by the Nuclear Energy Agency as a priority nuclear data need, complementary experiments, one at the GELINA and two at the n_TOF facility, were pr...

Accident progression event tree analysis for postulated severe accidents at N Reactor

International Nuclear Information System (INIS)

Wyss, G.D.; Camp, A.L.; Miller, L.A.; Dingman, S.E.; Kunsman, D.M.; Medford, G.T.

1990-06-01

A Level II/III probabilistic risk assessment (PRA) has been performed for N Reactor, a Department of Energy (DOE) production reactor located on the Hanford reservation in Washington. The accident progression analysis documented in this report determines how core damage accidents identified in the Level I PRA progress from fuel damage to confinement response and potential releases the environment. The objectives of the study are to generate accident progression data for the Level II/III PRA source term model and to identify changes that could improve plant response under accident conditions. The scope of the analysis is comprehensive, excluding only sabotage and operator errors of commission. State-of-the-art methodology is employed based largely on the methods developed by Sandia for the US Nuclear Regulatory Commission in support of the NUREG-1150 study. The accident progression model allows complex interactions and dependencies between systems to be explicitly considered. Latin Hypecube sampling was used to assess the phenomenological and systemic uncertainties associated with the primary and confinement system responses to the core damage accident. The results of the analysis show that the N Reactor confinement concept provides significant radiological protection for most of the accident progression pathways studied

Utilization of the {sup 93}Nb(n,n'){sup 93}Nb{sup m} Reaction for for Reactor Neutron Dosimetry

Energy Technology Data Exchange (ETDEWEB)

Czock, K. H.; Houtermans, H. [International Atomic Energy Agency, Division of Research and Laboratories, Vienna (Austria)

1974-09-15

For the measurement of large ({Phi}>10{sup 18}n/cm{sup 2}) fast neutron fluences in research reactors, the reaction {sup 93}Nb(n,n'){sup 93}Nb{sup m} is fairly seldom used (Lloret, Hegedus). The reason is that the excitation function for the production of the {sup 93}Nb isomeric state (half-life{approx_equal}11.4 years) by inelastic neutron scattering is nearly unknown. Also the determination of the absolute {sup 93}Nb{sup m} activity is difficult, e.g. due to the bad knowledge of the conversion coefficients {alpha}{sub tot} and {alpha}{sub K}. But for neutron dosimetry purposes one does not necessarily need absolute activity values, if one irradiated niobium foil (e.g. 10 mm empty and 0.1 mm thick) is accepted to be a reference source to other irradiated niobium foils (of the same original material). If the cross section measurements and the fluence determinations are both based on the same reference source {sup 93}Nb{sup m} as an arbitrary activity standard, the possible inaccuracy of this activity value would not matter. Such an accepted reference source could be deposited at one central institution. Once the reference source activity is defined (at present within 30% of the true absolute activity value) niobium sources with activities determined relative to this reference source could be supplied together with non-irradiated niobium foils to interested laboratories. (author)

On the failure modes of alternative containment designs following postulated core meltdown

International Nuclear Information System (INIS)

Chan, C.K.; Knee, H.E.; Okrent, D.

1977-01-01

The containment response to a postulated core meltdown accident in a PWR ice condenser containment, a BWR Mark III containment and a BWR non-inerted Mark I containment has been examined to see if the WASH-1400 containment failure mode judgement for the Surry large, dry containment and the Peach Bottom Mark I inerted-containment are likely to be appropriate for these alternative containment plant designs. For the PWR, the representative accident chosen for the analysis is a large cold leg break accompanied by a loss of all electric power while the BWR respresentative event chosen is a recirculation line break without adequate core cooling function. Two containment event paths are studied for each of these two cases, depending on whether or not containment vapor suppression function is assumed to be available. Both the core and the containment pressure and temperature response to the accident events are computed for the four time intervals which characterize (a) blowdown of the pipe break, (b) core melt, (c) vessel melt-through, and (d) containment foundation penetration. The calculations are based on a best esimate of the most probable sequence, but certain phenomena and events were followed down multiple tracks. It appears that the non-inerted Mark I containment is not so vulnerable to overpressurization from hydrogen burning as the Mark III; however, acceptable temperatures may be exceeded. (Auth.)

Corrosión de componentes de aluminio en el reactor RP-10

OpenAIRE

Morales Larrea, Soledad; Tenorio de la Cruz, Favio

1983-01-01

Se analiza la velocidad de corrosión, por pérdida de peso de placas de aluminio a diversos valores de pH y temperatura en solución acuosa. El estudio se hace simulando las condiciones de trabajo (pH y temperatura) a las que pueden verse sometidas las vainas de aluminio de los elementos combustibles del reactor RP-10.

The 5th surveillance testing for Kori unit 1 reactor vessel materials

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwun Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

2000-08-01

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 5th surveillance testing was performed primarily by Korea Atomic Energy Research Institute and Westinhouse corporation partially involved in testing and calculation data evaluation in order to obtain reliable test result. Fast neutron fluences for capsule V, T, S, R and P were 5.087E+18, 1.115E+19, 1.228E+19, 2.988E+19, and 3.938E+19n/cm2, respectively. The bias factor, the ratio of calculation/measurement, was 0.940 for the 1st through 5th testing and the calculational uncertainty, 7% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.9846E+19n/cm{sup 2} based on the end of 17th fuel cycle and it was predicted that the fluences of vessel inside surface at 24, 32, 40 and 48EFPY would reach 3.0593E+19, 4.0695E+19, 5.0797E+19 and 6.0900E+19n/cm{sup 2} based on the current calculation. PTS analysis for Kori unit 1 showed that 27.93EFPY was the threshold value for 300 deg F requirement. 71 refs., 33 figs., 52 tabs. (Author)

State-of-the-art incore detector system provides operational and safety benefits: Example, Hanford N Reactor

International Nuclear Information System (INIS)

Toffer, H.

1988-08-01

A presentation on the operational and safety benefits that can be derived from a state-of-the-art incore neutron monitoring system has been prepared for the DOE/ANL training course on ''The Potential Safety Impact of New and Emerging Technologies on the Operation of DOE Nuclear Facilities.'' Advanced incore neutron flux monitoring systems have been installed in some commercial reactors and should be considered for any new reactor designs or as backfits to existing plants. The recent installation of such a system at the Hanford N Reactor is used as an example in this presentation. Unfortunately, N Reactor has been placed in a cold standby condition and the full core incore system has not been tested under power conditions. Nevertheless, the evaluations that preceded the installation of the full core system provide interesting insight into the operational and safety benefits that could be expected

IRPhE/STEK, Reactor Physics Experiments from Fast-Thermal Coupled Facility

International Nuclear Information System (INIS)

Dietze, Klaus; Klippel, Henk Th.; Koning, Arjan; Jacqmin, Robert

2003-01-01

1 - Description: The STEK-experiments have been performed to check neutron data of the most important reactor materials, especially of fission product nuclides, fuel isotopes and structural materials. The measured central reactivity worths (CRW) of small samples were compared with calculated values. These C/E-ratios have been used then for data corrections or in adjustment procedures. The reactors STEK (ECN Petten/ Netherlands) was a fast-thermal coupled facility of zero power. The annular thermal drivers were filled by fuel assemblies and moderated by water. The inner insertion lattices were loaded with pellets of fuel and other materials producing the fast neutron flux. The characteristics of the neutron and adjoint spectra were obtained by special arrangements of these pellets in unit cells. In this way, a hard or soft neutron spectrum or a special energy behavior of the adjoint function could be reached. The samples were moved by means of tubes to the central position (pile-oscillation technique). The original information about the facility and measurements is compiled in RCN-209, ECN-10 The 5 STEK configurations cover a broad energy range due to their increasing softness. The experiments are very valuable because of the extensive program of sample reactivity measurements with many fission product nuclides important in reactor burn-up calculations. At first, analyses of the experiments have been performed in Petten. Newer analyses were done later in Cadarache / CEA France using the European scheme for reactor calculation JEF-2.2 / ECCO / ERANOS (see Note Techniques and JEF/DOC-746). Furthermore, re-analyses were performed in O-arai / JNC Japan with the JNC standard route JENDL-3.2 / SLAROM / CITATION / PERKY. Results obtained with both code systems and different data evaluations (JEF-2.2 and JENDL-3.2) are compared in JEF/DOC-861. It contains the following documents: 31 Reports, 2 publications, 5 JEF documents, 4 conferences. 2 - Related or auxiliary programs

Metallographic examination of damaged N reactor spent nuclear fuel element SFEC5,4378

Energy Technology Data Exchange (ETDEWEB)

Marschman, S.C.; Pyecha, T.D.; Abrefah, J.

1997-08-01

N-Reactor spent nuclear fuel (SNF) is currently residing underwater in the K Basins at the Hanford site, in Richland, Washington. This report presents results of the metallographic examination of specimens cut from an SNF element (Mark IV-E) with breached cladding. The element had resided in the K-West (KW) Storage Basin for at least 10 years after it was discharged from the N-Reactor. The storage containers in the KW Basin were nominally closed, isolating the SNF elements from the open pool environment. Seven specimens from this Mark IV-E outer fuel element were examined using an optical metallograph. Included were two specimens that had been subjected to a conditioning process recommended by the Independent Technical Assessment Team, two specimens that had been subjected to a conditioning process recommended in the Integrated Process Strategy Report, and three that were in the as-received, as-cut condition. One of the as-received specimens had been cut from the damaged (or breached) end of the element. All other specimens were cut from the undamaged mid-region of the fuel element. The specimens were visually examined to (1) identify uranium hydride inclusions present in the uranium metal fuel, (2) measure the thickness of the oxide layer formed on the uranium edges and assess the apparent integrity and adhesion of the oxide layer, and (3) look for features in the microstructure that might provide an insight into the various corrosion processes that occurred during underwater storage in the KW Basin. These features included, but were not limited to, the integrity of the cladding and the fuel-to-cladding bond, obvious anomalies in the microstructure, excessive pitting or friability of the fuel matrix, and obvious anomalies in the distribution of uranium hydride or uranium carbide inclusions. Also, the observed metallographic features of the conditioned specimens were compared with those of the as-received (unconditioned) specimens. 11 refs., 93 figs., 2 tabs.

Average cross-sections for /n, p/ reactions on calcium in a fission-type reactor spectrum

International Nuclear Information System (INIS)

Bruggeman, A.; Maenhaut, W.; Hoste, J.

1974-01-01

The average cross-section in a fission-type reactor spectrum sigmasub(F) was experimentally determined for the reactions 42 Ca/n,p/ 42 K, 43 Ca/n,p/ 43 K and 44 Ca/n,p/ 44 K. Calcium carbonate samples and fast neutron flux monitors were irradiated with and without cadmium shielding in the Thetis reactor (Institute for Nuclear Sciences, Rijksuniversiteit Gent). The potassium activities induced in the calcium carbonate samples were separated and purified by tetraphenylborate precipitation, after which they were measured with a Ge/Li/-detector of calibrated detection efficiency. On the basis of sigmasub(F)=0.64 mb for the reaction 27 Al/n,α/ 24 Na, the average cross-sections were as follows: 42 Ca/n,p/ 42 K: 2.82+-0.07 mb; 43 Ca/n,p/ 43 K: 1.89+-0.05 mb; 44 Ca/n,p/ 44 K: 0.065+-0.003 mb. (T.G.)

Dose estimation for nuclear power plant 4 accident in Taiwan at Fukushima nuclear meltdown emission level

International Nuclear Information System (INIS)

Tang, Mei-Ling; Tsuang, Ben-Jei; Kuo, Pei-Hsuan

2016-01-01

An advanced Gaussian trajectory dispersion model is used to evaluate the evacuation zone due to a nuclear meltdown at the Nuclear Power Plant 4 (NPP4) in Taiwan, with the same emission level as that occurred at Fukushima nuclear meltdown (FNM) in 2011. Our study demonstrates that a FNM emission level would pollute 9% of the island's land area with annual effective dose ≥50 mSv using the meteorological data on 11 March 2011 in Taiwan. This high dose area is also called permanent evacuation zone (denoted as PEZ). The PEZ as well as the emergency-planning zone (EPZ) are found to be sensitive to meteorological conditions on the event. In a sunny day under the dominated NE wind conditions, the EPZ can be as far as 100 km with the first 7-day dose ≥20 mSv. Three hundred sixty-five daily events using the meteorological data from 11 March 2011 to 9 March 2012 are evaluated. It is found that the mean land area of Taiwan in becoming the PEZ is 11%. Especially, the probabilities of the northern counties/cities (Keelung, New Taipei, Taipei, Taoyuan, Hsinchu City, Hsinchu County and Ilan County) to be PEZs are high, ranging from 15% in Ilan County to 51% in Keelung City. Note that the total population of the above cities/counties is as high as 10 million people. Moreover, the western valleys of the Central Mountain Range are also found to be probable being PEZs, where all of the reservoirs in western Taiwan are located. For example, the probability can be as high as 3% in the far southern-most tip of Taiwan Island in Pingtung County. This shows that the entire populations in western Taiwan can be at risk due to the shortage of clean water sources under an event at FNM emission level, especially during the NE monsoon period. - Highlights: • An advanced Gaussian-type trajectory model to evaluate the evacuation zone at Nuclear Power Plant 4 in Taiwan. • Mean land area of Taiwan in becoming the permanent evacuation zone is 11%. • The probabilities of the northern

Assessment of mass fraction and melting temperature for the application of limestone concrete and siliceous concrete to nuclear reactor basemat considering molten core-concrete interaction

Energy Technology Data Exchange (ETDEWEB)

Lee, Ho Jae; Kim, Do Gyeum [Korea Institute of Civil Engineering and Building Technology, Goyang (Korea, Republic of); Cho, Jae Leon [Korea Hydro and Nuclear Power Co., Ulsan (Korea, Republic of); Yoon, Eui Sik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of); Cho, Myung Suk [Korea Hydro and Nuclear Power Co., Central Research Institute, Daejeon (Korea, Republic of)

2016-04-15

Severe accident scenarios in nuclear reactors, such as nuclear meltdown, reveal that an extremely hot molten core may fall into the nuclear reactor cavity and seriously affect the safety of the nuclear containment vessel due to the chain reaction caused by the reaction between the molten core and concrete. This paper reports on research focused on the type and amount of vapor produced during the reaction between a high-temperature molten core and concrete, as well as on the erosion rate of concrete and the heat transfer characteristics at its vicinity. This study identifies the mass fraction and melting temperature as the most influential properties of concrete necessary for a safety analysis conducted in relation to the thermal interaction between the molten core and the basemat concrete. The types of concrete that are actually used in nuclear reactor cavities were investigated. The H2O content in concrete required for the computation of the relative amount of gases generated by the chemical reaction of the vapor, the quantity of CO2 necessary for computing the cooling speed of the molten core, and the melting temperature of concrete are evaluated experimentally for the molten core-concrete interaction analysis.

Comparison of neutron parameters between a CANDU and ACR reactors; Comparacao de parametros neutronicos entre um reator CANDU e um ACR

Energy Technology Data Exchange (ETDEWEB)

Dias, Gabriel H.P.; Silva, Clarysson A.M. da; Pereira, Claubia, E-mail: gabrielhpd@yahoo.com.br, E-mail: clarysson@nuclear.ufmg.br, E-mail: claubia@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear

2017-11-01

CANDU (Canadian Deuterium Uranium) is a type of reactor that uses heavy water (D{sub 2}O) as a moderator and as a refrigerant. Despite having chemical characteristics similar to light water (H{sub 2}O), heavy water has a high moderation ratio for neutrons. This feature enables CANDU to use natural uranium as fuel. However, research has evaluated the possibility of using H{sub 2}O as a refrigerant and D{sub 2}O as a moderator aiming at reducing the volume of heavy water. Such changes would imply the use of lightly enriched uranium due to the presence of H{sub 2}O. In this context, the concept of ACR (Advanced CANDU Reactor) has been developed. This reactor has an innovative design which combines of the current CANDU with the characteristics of PWR (Pressurized Water Reactor) type reactors. Studies by AECL (Atomic Energy Canada Limited) show that compared to CANDU, the ACR presents a cost reduction in construction, improved firing performance, improved operation safety and longer life. The present work aims to evaluate, in steady state, some of the main neutron parameters of CANDU-6 and ACR-1000. The MCNPX 2.6.0 code (Monte Carlo N-Particle eXtended -version 2.6.0) was used to simulate such types of reactors. The results show that the models configured in the MCNPX adequately reproduce the neutron behavior of the studied reactors. These models may be used in future work for analysis of fuel burn and evolution.

Reactores aeróbios de lecho fluidizado trifásico con circulación interna: caracterización hidrodinámica y del soporte

Directory of Open Access Journals (Sweden)

Iván Andrés Sánchez Ortiz

2010-01-01

Full Text Available Los reactores aerobios de lecho fluidizado con circulación interna utilizan biomasa activa adherida a un medio soporte (biopelícula, con la ventaja de retener gran concentración de la misma, utilizando poco espacio físico y pudiendo remover, en un mismo reactor, materia carbonácea y nitrogenada. La circulación del líquido ocurre debido a la diferencia de presión hidrostática producida por la inyección de aire en el tubo de subida. En la condición de medio bifásico fueron estudiadas las velocidades de circulación, fracción volumétrica de aire y coeficiente de transferencia de oxígeno, utilizando cuatro configuraciones de reactores. En medio trifásico se evaluaron las velocidades de circulación, la fracción volumétrica de aire y el coeficiente de transferencia de oxígeno en una de dichas configuraciones. También se realizó la caracterización de tres posibles medios de soporte granulares. Se determinó que la relación de áreas entre los tubos interno y externo y la concentración de medio soporte influencian los valores de velocidad de circulación del líquido, de la fracción volumétrica de aire y de la transferencia de oxígeno y se observaron y compararon características importantes de los medios de soporte.

The ICRH tokamak fusion test reactor

International Nuclear Information System (INIS)

Perkins, F.W.

1976-01-01

A Tokamak Fusion Test Reactor where the ion are maintained at Tsub(i) approximately 20keV>Tsub(e) approximately 7keV by ion-cyclotron resonance heating is shown to produce an energy amplification of Q>2 provided the principal ion energy loss channel is via collisional transfer to the electrons. Such a reactor produces 19MW of fusion power to the electrons. Such a reactor produces 19MW of fusion power and requires a 50MHz radio-frequency generator capable of 50MW peak power; it is otherwise compatible with the conceptual design for the Princeton TFTR. The required n tausub(E) values for electrons and ions are respectively ntausub(Ee)>1.5.10 13 cm -3 -sec and ntausub(Ei)>4.10 13 cm -3 -sec. The principal areas where research is needed to establish this concept are: tokamak transport calculations, ICRH physics, trapped-particle instability energy losses, tokamak equilibria with high values of βsub(theta), and, of course, impurities

Search for eV sterile neutrinos at a nuclear reactor — the Stereo project

Science.gov (United States)

Haser, J.; Stereo Collaboration

2016-05-01

The re-analyses of the reference spectra of reactor antineutrinos together with a revised neutrino interaction cross section enlarged the absolute normalization of the predicted neutrino flux. The tension between previous reactor measurements and the new prediction is significant at 2.7 σ and is known as “reactor antineutrino anomaly”. In combination with other anomalies encountered in neutrino oscillation measurements, this observation revived speculations about the existence of a sterile neutrino in the eV mass range. Mixing of this light sterile neutrino with the active flavours would lead to a modification of the detected antineutrino flux. An oscillation pattern in energy and space could be resolved by a detector at a distance of few meters from a reactor core: the neutrino detector of the Stereo project will be located at about 10 m distance from the ILL research reactor in Grenoble, France. Lengthwise separated in six target cells filled with 2 m3 Gd-loaded liquid scintillator in total, the experiment will search for a position-dependent distortion in the energy spectrum.

Prediction of thermoplastic failure of a reactor pressure vessel under a postulated core melt accident

International Nuclear Information System (INIS)

Duijvestijn, G.; Birchley, J.; Reichlin, K.

1997-01-01

This paper presents the lower head failure calculations performed for a postulated accident scenario in a commercial nuclear power plant. A postulated one inch break in the primary coolant circuit leads to dryout and subsequent meltdown of the core. The reference plant is a pressurized water reactor without penetrations in the reactor vessel lower head. The molten core material accumulates in the lower head, eventually causing failure of the vessel. The analysis investigates flow conditions in the melt pool, temperature evolution in the reactor vessel wall, and structure mechanical evaluation of the vessel under strong thermal loads and a range of internal pressures. The calculations were performed using the ADINA finite element codes. The analysis focusses on the failure processes, time and mode of failure. The most likely mode of failure at low pressure is global rupture due to gradual accumulation of creep strain over a large part of the heated area. In contrast, thermoplasticity becomes important at high pressure or following a pressure spike and can lead to earlier local failure. In situations in which part of the heat load is concentrated over a small area, resulting in a hot spot, local failure occurs, but not until the temperatures are close to the melting point. At low pressure, in particular, the hot spot area remains intact until the structure is molten across more than half of the thickness. (author) 14 figs., 16 refs

Transportation risk assessment of radioactive wastes generated by the N-Reactor stabilization program at the Hanford Site, Washington

International Nuclear Information System (INIS)

Wheeler, T.

1994-12-01

The potential radiological and nonradiological risks associated with specific radioactive waste shipping campaigns at the Hanford Site are estimated. The shipping campaigns analyzed are associated with the transportation of wastes from the N-Reactor site at the 200-W Area, both within the Hanford Reservation, for disposal. The analysis is based on waste that would be generated from the N-Reactor stabilization program

Estudio de distribución de tiempos de residencia en un reactor biológico de lecho empacado cerámico

Directory of Open Access Journals (Sweden)

Tatiana Rodríguez Chaparro

2004-01-01

Full Text Available La distribución de tiempos de residencia de un reactor es una característica del mezclado que ocurre dentro de él [ ] 1 [ ] 2 ; su determinación es básica para el diseño de cualquier tipo de reactor en escala real. El objetivo de esta investigación consistió en determinar la distribución de tiempos de residencia en un reactor biológico de lecho empacado cerámico (anillos a partir de pruebas con trazadores. Los resultados obtenidos utilizando las técnicas de inyección por paso y pulso fueron 34.577 seg., y 17.745 seg., respectivamente, y la dispersión calculada infinita. Lo anterior permite concluir que en reactores de lecho empacado cerámico (anillos las moléculas del trazador se distribuyen uniformemente en todo el sistema. Los ensayos se realizaron en un modelo a escala laboratorio.

15 N utilization in nitride nuclear fuels for advanced nuclear power reactors and accelerator - driven systems

International Nuclear Information System (INIS)

Axente, D.

2005-01-01

15 N utilization for nitride nuclear fuels production for nuclear power reactors and accelerator - driven systems is presented. Nitride nuclear fuel is the obvious choice for advanced nuclear reactors and ADS because of its favorable properties: a high melting point, excellent thermal conductivity, high fissile density, lower fission gas release and good radiation tolerance. The application of nitride fuels in nuclear reactors and ADS requires use of 15 N enriched nitrogen to suppress 14 C production due to (n,p) reaction on 14 N. Accelerator - driven system is a recent development merging of accelerator and fission reactor technologies to generate electricity and transmute long - lived radioactive wastes as minor actinides: Np, Am, Cm. A high-energy proton beam hitting a heavy metal target produces neutrons by spallation. The neutrons cause fission in the fuel, but unlike in conventional reactors, the fuel is sub-critical and fission ceases when the accelerator is turned off. Nitride fuel is a promising candidate for transmutation in ADS of minor actinides, which are converted into nitrides with 15 N for that purpose. Tacking into account that the world wide market is about 20 to 40 Kg 15 N annually, the supply of that isotope for nitride fuel production for nuclear power reactors and ADS would therefore demand an increase in production capacity by a factor of 1000. For an industrial plant producing 100 t/y 15 N, using present technology of isotopic exchange in NITROX system, the first separation stage of the cascade would be fed with 10M HNO 3 solution of 600 mc/h flow - rate. If conversion of HNO 3 into NO, NO 2 , at the enriching end of the columns, would be done with gaseous SO 2 , for a production plant of 100 t/y 15 N a consumption of 4 million t SO 2 /y and a production of 70 % H 2 SO 4 waste solution of 4.5 million mc/y are estimated. The reconversion of H 2 SO 4 into SO 2 in order to recycle of SO 2 is a problem to be solved to compensate the cost of SO 2

Can the acceptance of nuclear reactors be raised by a simpler, more transparent safety concept employing improved containments?

International Nuclear Information System (INIS)

Krieg, R.

1993-01-01

Sociological and psychological findings are presented which describe problems society faces with risky technologies. It turns out that for a small but influential group of the society not only the risk, but also the transparency of the technology and the engineered safeguards are important. For this group an improvement of the transparency should raise the acceptance of the technology. However, for the majority of the public, broad discussions about a different more transparent safety concept could generate a feeling of insecurity, especially concerning existing nuclear power plants. In order to improve the transparency in engineered safeguards of nuclear reactors, four basic principles are introduced. Nuclear containments, which remain intact after failure of all emergency cooling systems resulting in a core meltdown accident with steam and hydrogen explosions, are in line with these principles. Such containments are under investigation in Germany right now. It is pointed out that the public should be informed prudently about this work to improve the containments, and the required transparency of the engineered safeguards should be underlined as a major goal. Vague descriptions, providing only superficially information about safer reactors, could easily cause misunderstandings. If one goes along this line a simpler and more transparent safety concept employing improved containments will have the potential to raise the acceptance of nuclear reactors. (orig.)

An automatic device for sample insertion and extraction to/from reactor irradiation facilities

International Nuclear Information System (INIS)

Alloni, L.; Venturelli, A.; Meloni, S.

1990-01-01

At the previous European Triga Users Conference in Vienna,a paper was given describing a new handling tool for irradiated samples at the L.E.N.A plant. This tool was the first part of an automatic device for the management of samples to be irradiated in the TRIGA MARK ii reactor and successively extracted and stored. So far sample insertion and extraction to/from irradiation facilities available on reactor top (central thimble,rotatory specimen rack and channel f),has been carried out manually by reactor and health-physics operators using the ''traditional'' fishing pole provided by General Atomic, thus exposing reactor personnel to ''unjustified'' radiation doses. The present paper describes the design and the operation of a new device, a ''robot''type machine,which, remotely operated, takes care of sample insertion into the different irradiation facilities,sample extraction after irradiation and connection to the storage pits already described. The extraction of irradiated sample does not require the presence of reactor personnel on the reactor top and,therefore,radiation doses are strongly reduced. All work from design to construction has been carried out by the personnel of the electronic group of the L.E.N.A plant. (orig.)

Nuclear research reactors

International Nuclear Information System (INIS)

1985-01-01

It's presented data about nuclear research reactors in the world, retrieved from the Sien (Nuclear and Energetic Information System) data bank. The information are organized in table forms as follows: research reactors by countries; research reactors by type; research reactors by fuel and research reactors by purpose. (E.G.) [pt

Biological biogas upgrading capacity of a hydrogenotrophic community in a trickle-bed reactor

International Nuclear Information System (INIS)

Rachbauer, Lydia; Voitl, Gregor; Bochmann, Günther; Fuchs, Werner

2016-01-01

Highlights: • Data on long term operation of a system supplied with real biogas are presented. • Ex-situ biological methanation is feasible for biogas upgrading. • Gas quality obtained complies with strictest direct grid injection criteria. • Biomethane can act as flexible storage for renewable surplus electricity. - Abstract: The current study reports on biological biogas upgrading by means of hydrogen addition to obtain biomethane. A mesophilic (37 °C) 0.058 m"3 trickle-bed reactor with an immobilized hydrogenotrophic enrichment culture was operated for a period of 8 months using a substrate mix of molecular hydrogen (H_2) and biogas (36–42% CO_2). Complete CO_2 conversion (> 96%) was achieved up to a H_2 loading rate of 6.5 m_n"3 H_2/m"3_r_e_a_c_t_o_r _v_o_l_. × d, corresponding to 2.3 h gas retention time. The optimum H_2/CO_2 ratio was determined to be between 3.67 and 4.15. CH_4 concentrations above 96% were achieved with less than 0.1% residual H_2. This gas quality complies even with tightest standards for grid injection without the need for additional CO_2 removal. If less rigid standards must be fulfilled H_2 loading rates can be almost doubled (10.95 versus 6.5 m_n"3 H_2/m"3_r_e_a_c_t_o_r _v_o_l_. × d) making the process even more attractive. At this H_2 loading the achieved methane productivity was 2.52 m_n"3 CH_4/m"3_r_e_a_c_t_o_r _v_o_l_. × d. In terms of biogas this corresponds to an upgrading capacity of 6.9 m_n"3 biogas/m"3_r_e_a_c_t_o_r _v_o_l_. × d. The conducted experiments demonstrate that biological methanation in an external reactor is well feasible for biogas upgrading under the prerequisite that an adequate H_2 source is available.

Reactor core of FBR type reactor

International Nuclear Information System (INIS)

Hayashi, Hideyuki; Ichimiya, Masakazu.

1994-01-01

A reactor core is a homogeneous reactor core divided into two regions of an inner reactor core region at the center and an outer reactor core region surrounding the outside of the inner reactor core region. In this case, the inner reactor core region has a lower plutonium enrichment degree and less amount of neutron leakage in the radial direction, and the outer reactor core region has higher plutonium enrichment degree and greater amount of neutron leakage in the radial direction. Moderator materials containing hydrogen are added only to the inner reactor core fuels in the inner reactor core region. Pins loaded with the fuels with addition of the moderator materials are inserted at a ratio of from 3 to 10% of the total number of the fuel pins. The moderator materials containing hydrogen comprise zirconium hydride, titanium hydride, or calcium hydride. With such a constitution, fluctuation of the power distribution in the radial direction along with burning is suppressed. In addition, an absolute value of the Doppler coefficient can be increased, and a temperature coefficient of coolants can be reduced. (I.N.)

Determination of the neutron spectrum at different locations in the Argentine RA-1 Reactor; Determinacion del espectro neutronico en distintas posiciones del reactor RA-1

Energy Technology Data Exchange (ETDEWEB)

Lerner, A M; Madariaga, M R [Autoridad Regulatoria Nuclear, Buenos Aires (Argentina)

1999-12-31

Full text: It is well known that the RA-1 reactor is used to irradiate different types of materials with neutrons. The Radio dosimetry Group (which belongs to the Nuclear Regulatory Authority) uses its fast column for the design, calibration and set up of criticality dosimeters as well as for a quick assessment of the dose to workers in case of an accident. With such purpose, Au(1), Au under Cd and In(2) foils were irradiated to estimate absolute thermal, epithermal and fast neutron fluxes at the irradiation location. The accuracy of this estimation is higher when the response to the present neutron spectrum of the different materials constituting the detectors is better known. This, in turn, requires the previous knowledge of such spectrum (a detailed energy dependence of neutron flux) at the analysed location. In this work a neutronic calculation is presented at the fast irradiation location. The whole calculation was carried out following two different methodologies, and considering a power of 40 kW. The reactor and its surroundings were represented by a simplified one-dimensional model, as a concentric cylindrical set of regions. Figures are drawn representing fast and thermal fluxes (with the cut at 0.4 eV) as a function of the distance to the core centre. The neutron flux (in n/cm{sup 2}sec.eV) as a function of energy is also shown at the fast irradiation location. Values of flux (in n/cm{sup 2}.sec.eV) are also provided as a function of energy in other typical locations, as well as the equivalent integrated flux values (in n/cm{sup 2}.sec). ((1) According to the reaction Au{sup 197}(n,{gamma})Au{sup 198}, having a cross section of {sigma}{sub 0}=98.8b for thermal neutrons. (2) According to the reaction In{sup 115}(n,n`)In{sup 115m}, with a cross section of some 70 mb for neutrons with energies above 1.2MeV). (author) [Espanol] Texto completo: Como se sabe, el reactor RA1 se utiliza para irradiar con neutrones distintos tipos de materiales. El grupo de

N2O Catalytic Decomposition – from Laboratory Experiment to Industry Reactor

Czech Academy of Sciences Publication Activity Database

Obalová, L.; Jirátová, Květa; Karásková, K.; Chromčáková, Ž.

2012-01-01

Roč. 191, č. 1 (2012), s. 116-120 ISSN 0920-5861 R&D Projects: GA TA ČR TA01020336 Institutional support: RVO:67985858 Keywords : N2O * catalytic decomposition * fixed bed reactor Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.980, year: 2012

Estudio mecánico e hidrodinámico de un reactor de gasificación de lecho fluidizado. // Mechanic and hydrodynamic study of a fluidized bed gasification reactor.

Directory of Open Access Journals (Sweden)

W. Rosales

2008-01-01

Full Text Available Se realizó una simulación mediante Elementos Finitos y CFD de un prototipo de gasificador experimental a partir de unageometría propuesta. Se abordan aspectos termomecánicos, al calcularse las deformaciones originadas en el equipo,producto de su peso, en las condiciones de emplazamiento y la carga térmica a la que se somete. También se considera elflujo multifásico gas-sólido presente en el lecho fluidizado, se determina el rango de presiones y velocidades de trabajo deldispositivo, y se estudia la evolución del flujo. Para ello se utiliza el modelo de fuerza de arrastre y presión de sólido deGidaspow, así como los criterios de velocidad mínima de fluidización de Wen & Yu y Kunii & Levenspiel.Palabras claves: Gasificación, lecho fluidizado, CFD, FEM, flujo multifásico.______________________________________________________________________________Abstract.A Finite Element and CFD simulations were conducted to a prototype of experimental gasifier, starting from a proposedgeometry. Thermomechanic aspects are briefed, calculating the reactor deformation, due to its weight and the thermic load.The gas-solid multiphase flow, present on the fluidized bed was also considered, the working range for the pressure andvelocity fields were determined and the flow evolution was studied. The drag force and solid pressure models byGidaspow, and the minimum fluidization velocity criteria, by Wen & Yu and Kunii & Levenspiel were used.Key words: gasification, fluidized bed, CFD, Finite Element, Multiphase Flow.

A WIMS E analysis of zero energy experiments performed on the Dragon reactor

Energy Technology Data Exchange (ETDEWEB)

Lancefield, M. J.; Broadhouse, B.; Woloch, F.

1974-10-15

UKAEA methods embodied in the WINS-E modular scheme of codes are described in their application to the analysis of zero energy experiments performed on the DRAGON reactor. Measured reactivity and reaction rate distributions are compared with the predictions of the analysis.

Power measurement of the RA-3 reactor using the neutron noise technique and 16N

International Nuclear Information System (INIS)

Gomez, Angel

2003-01-01

This work describes a measurement method based on the neutron noise technique which is used for determining the relation between the power and the currents of two ionization chambers. These chambers are sensitive to the gamma radiation from the 16 N decay produced in the RA-3 reactor core. The power during operation is obtained from the calibration factors by measuring those currents. As this calibration factors depend on the cooler flow that circulates in the reactor core and in the 16 N measuring system, an estimator, that is a function of the ratio of this currents, is proposed in order to detect flow changes. (author)

Proposal for computer investigation of LMFBR core meltdown accidents

International Nuclear Information System (INIS)

Boudreau, J.E.; Harlow, F.H.; Reed, W.H.; Barnes, J.F.

1974-01-01

The environmental consequences of an LMFBR accident involving breach of containment are so severe that such accidents must not be allowed to happen. Present methods for analyzing hypothetical core disruptive accidents like a loss of flow with failure to scram cannot show conclusively that such accidents do not lead to a rupture of the pressure vessel. A major deficiency of present methods is their inability to follow large motions of a molten LMFBR core. Such motions may lead to a secondary supercritical configuration with a subsequent energy release that is sufficient to rupture the pressure vessel. The Los Alamos Scientific Laboratory proposes to develop a computer program for describing the dynamics of hypothetical accidents. This computer program will utilize implicit Eulerian fluid dynamics methods coupled with a time-dependent transport theory description of the neutronic behavior. This program will be capable of following core motions until a stable coolable configuration is reached. Survey calculations of reactor accidents with a variety of initiating events will be performed for reactors under current design to assess the safety of such reactors

Análisis de estabilidad del reactor PFTR para una reacción con cinética de primer orden utilizando la funcional de Lyapunov

OpenAIRE

Héctor Armando Durán Peralta; Luis Fernando Córdoba C

2007-01-01

Abunda la literatura referente al análisis de estabilidad de reactores con parámetros globalizados de concentración y temperatura (por ejemplo el CSTR), en cambio es escasa la literatura sobre la estabilidad de reactores con parámetros distribuidos donde existe distribución espacial de concentración y temperatura, como es el caso del reactor tubular PFTR. Este documento analiza la estabilidad del reactor PFTR isotérmico y no isotérmico para una reacción con cinética de primer orden utilizando...

Análisis de estabilidad del reactor pftr para una reacción con cinética de primer orden utilizando la funcional de lyapunov

OpenAIRE

Durán Peralta, Héctor Armando; Córdoba C, Luis Fernando

2010-01-01

Abunda la literatura referente al análisis de estabilidad de reactores con parámetros globalizados de concentración y temperatura (por ejemplo el CSTR), en cambio es escasa la literatura sobre la estabilidad de reactores con parámetros distribuidos donde existe distribución espacial de concentración y temperatura, como es el caso del reactor tubular PFTR. Este documento analiza la estabilidad del reactor PFTR isotérmico y no isotérmico para una reacción con cinética de primer orden utilizand...

Simulating single-event burnout of n-channel power MOSFET's

International Nuclear Information System (INIS)

Johnson, G.H.; Hohl, J.H.; Schrimpf, R.D.; Galloway, K.F.

1993-01-01

Heavy ions are ubiquitous in a space environment. Single-event burnout of power MOSFET's is a sudden catastrophic failure mechanism that is initiated by the passage of a heavy ion through the device structure. The passage of the heavy ion generates a current filament that locally turns on a parasitic n-p-n transistor inherent to the power MOSFET. Subsequent high currents and high voltage in the device induce second breakdown of the parasitic bipolar transistor and hence meltdown of the device. This paper presents a model that can be used for simulating the burnout mechanism in order to gain insight into the significant device parameters that most influence the single-event burnout susceptibility of n-channel power MOSFET's

Review of Past Reactor Activities in Italy, April 1975

International Nuclear Information System (INIS)

Pierantoni, P.

1975-01-01

Since the last meeting of the International Working Group on Fast Reactors the natural vocation of the italian program to a cooperation, illustrated on many occasions, has found factual confirmation. As well-known, a broad partnership with France has been entered into. Four agreements have been concluded, towards May-June 1974 - between C.E.A. and C.N.E.N. for the ulterior development of the French filière and the construction and use of PEC; - between C.E.A. and NIRA for the license on the system; - between C.E.A. and AGIP-NUCLEARE for the fabrication of fuel for fast reactors; - between TECHNICATOME and NIRA for the preparation of the offer and the later construction of Super-Phenix. Those agreements are in the full logic of the previous one passed between the producers E.d.F., ENEL and R.W.E. for the construction of the first two commercial-size plants, extrapolated from Phenix and S.N.R. 300. In particular the NERSA society, acting as client for Super-Phenix, has been founded by those same producers and will receive the offer now prepared by a joint team. The new orientation of the programme and the validity of the previous agreements for its implementation have been confirmed at governmental level by the Interministerial Economic Planning Committee (CIPE), which has also approved the third CNEN's five years Plan

Investigation of (n,γ) reaction in hybrid reactor zones

International Nuclear Information System (INIS)

Guenay, Mehtap

2014-01-01

In this study, the fluids were composed with increased mole fractions of a mixture of molten salt: heavy metals 99-95 % Li 20 Sn 80 - 1-5 % SFG-Pu, 99-95 % Li 20 Sn 80 - 1-5 % SFG-PuF 4 , 99-95 % Li 20 Sn 80 - 1-5 % SFG-PuO 2 . In this study, the effect on conversion of each isotope ( 238-242 Pu) in spent fuel grade plutonium by (n,γ) reactions was investigated in liquid first wall, blanket and shield zones of the designed hybrid reactor system. Beryllium (Be) is the neutron multiplier by (n,2n) reactions. The Be zone used was 3 cm thick. 9Cr2WVT, a ferritic steel, is used as structural material. Three-dimensional nucleonic calculations were performed by using the most recent versions of the MCNPX-2.7.0 Monte Carlo code and the nuclear data library ENDF/B-VII.0.

Investigation of (n,γ) reaction in hybrid reactor zones

Energy Technology Data Exchange (ETDEWEB)

Guenay, Mehtap [Inoenue Univ., Malatya (Turkey). Physics Dept.

2014-12-15

In this study, the fluids were composed with increased mole fractions of a mixture of molten salt: heavy metals 99-95 % Li{sub 20}Sn{sub 80{sup -}}1-5 % SFG-Pu, 99-95 % Li{sub 20}Sn{sub 80{sup -}}1-5 % SFG-PuF{sub 4}, 99-95 % Li{sub 20}Sn{sub 80{sup -}}1-5 % SFG-PuO{sub 2}. In this study, the effect on conversion of each isotope ({sup 238-242}Pu) in spent fuel grade plutonium by (n,γ) reactions was investigated in liquid first wall, blanket and shield zones of the designed hybrid reactor system. Beryllium (Be) is the neutron multiplier by (n,2n) reactions. The Be zone used was 3 cm thick. 9Cr2WVT, a ferritic steel, is used as structural material. Three-dimensional nucleonic calculations were performed by using the most recent versions of the MCNPX-2.7.0 Monte Carlo code and the nuclear data library ENDF/B-VII.0.

Emergency response guide-B ECCS guideline evaluation analyses for N reactor

International Nuclear Information System (INIS)

Chapman, J.C.; Callow, R.A.

1989-07-01

INEL conducted two ECCS analyses for Westinghouse Hanford. Both analyses will assist in the evaluation of proposed changes to the N Reactor Emergency Response Guide-B (ERG-B) Emergency Core System (ECCS) guideline. The analyses were a sensitivity study for reduced-ECCS flow rates and a mechanistically determined confinement steam source for a delayed-ECCS LOCA sequence. The reduced-ECCS sensitivity study established the maximum allowable reduction in ECCS flow as a function of time after core refill for a large break loss-of-coolant accident (LOCA) sequence in the N Reactor. The maximum allowable ECCS flow reduction is defined as the maximum flow reduction for which ECCS continues to provide adequate core cooling. The delayed-ECCS analysis established the liquid and steam break flows and enthalpies during the reflood of a hot core following a delayed ECCS injection LOCA sequence. A simulation of a large, hot leg manifold break with a seven-minute ECCS injection delay was used as a representative LOCA sequence. Both analyses were perform using the RELAP5/MOD2.5 transient computer code. 13 refs., 17 figs., 3 tabs

Experimental cross section for the {sup 152}Sm(n, γ){sup 153}Sm reaction at 0.0334 eV

Energy Technology Data Exchange (ETDEWEB)

Uddin, M. Shuza; Datta, Tapash Kumar; Hossain, Syed Mohammod; Zakaria, A.K.M.; Islam, Mohammad Amirul; Naher, Kamrun; Shariff, M. Asad; Yunus, S.M. [Atomic Energy Research Establishment, Dhaka (Bangladesh). Inst. of Nuclear Science and Technology; Afroze, Nasmin [Atomic Energy Research Establishment, Dhaka (Bangladesh). Inst. of Nuclear Science and Technology; Jahangirnagar Univ., Dhaka (Bangladesh). Dept. of Physics; Islam, S.M. Ajharul [Jahangirnagar Univ., Dhaka (Bangladesh). Dept. of Physics

2014-10-01

The neutron capture cross section for the {sup 152}Sm(n, γ){sup 153}Sm reaction at an energy of 0.0334 eV was measured for the first time using monochromatic neutrons of a powder diffractometer at the TRIGA Mark II nuclear reactor at Dhaka, Bangladesh. The {sup 197}Au(n, γ){sup 198}Au reaction was used to monitor the neutron beam intensity. The radioactivity of the products was determined via high resolution γ-ray spectrometry. The obtained cross section value is 184 ± 22b, which is consistent with both the ENDF/B-VII and TENDL-2012 data libraries. The measured value at 0.0334 eV and the previous data at 0.0536 eV confirm the reliability of the data in the above libraries. (orig.)

How to arrest a core meltdown accident (doing nothing)

International Nuclear Information System (INIS)

Baron, Jorge H.

2000-01-01

In the eventual situation of a severe accident in a nuclear reactor, the molten core is able to relocate inside the pressure vessel. This may lead to the vessel failure, due to the thermal attack of the molten core (at approximation of 3000K) on the vessel steel wall. The vessel failure implies the failure of a very important barrier that contains the radioactive materials generated during the reactor operation, with a significant risk of producing high radiation doses both on operators and on the public. It is expected, for the new generation of nuclear reactors, that these will be required to withstand (by design) a core melt down accident, without the need for an immediate evacuation of the surrounding population. In this line, the use of a totally passive system is postulated, which fulfills the objective of containing the molten core inside the pressure vessel, at low temperature (approximation 1200K) precluding its failure. The conceptual design of a passive in-vessel core catcher is presented in this paper, built up of zinc, and designed for the CAREM-25 nuclear power plant. (author)

A second chance for nuclear power

International Nuclear Information System (INIS)

Martin, Richard

2017-01-01

At the Shanghai Institute of Applied Physics, China, there are plans to build an experimental molten- salt reactor whose design makes meltdown far less likely. A 'virtual' reactor displays an intricate system of pipes carrying the cooling fluid that makes this system special, and then carries heat to drive the turbine and make electricity. Alvin Weinberg was the pioneering nuclear physicist at Oak Ridge National Laboratory, who developed a prototype molten-salt reactor from 1965-1969, before it fell out of favour.

RB Research nuclear reactor RB reactor, Annual report for 2000

International Nuclear Information System (INIS)

Milosevic, M.

2000-12-01

Report on RB reactor operation during 2000 contains 3 parts. Part one contains a brief description of reactor operation and reactor components, relevant dosimetry data and radiation protection issues, personnel and financial data. Part two is devoted to maintenance of the reactor components, namely, fuel, heavy water, reactor vessel, heavy water circulation system, absorption rods and heavy water level-meters, maintenance of electronic, mechanical, electrical and auxiliary equipment. Part three contains data concerned with reactor operation and utilization with a comprehensive list of publications resulting from experiments done at the RB reactor. It contains data about reactor operation during previous 14 years, i.e. from 1986 - 2000

Status of national programmes on fast breeder reactors. Twenty-fifth annual meeting of the International Working Group on Fast Reactors. Summary report. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-07-01

At present nuclear power accounts for approximately 17% of total electricity generation worldwide. Given continuing population growth and the needs of the third world and developing countries to improve their economic performance and standard of living, energy demand is expected to continue to grow through the 21st century. The proportion of energy supplied as electricity is also expected to continue to increase. Although fossil fuelled electricity generation is the option preferred by several countries for the short term, there are rising concerns over climatic consequences caused by extended burning of fossil fuels as a result of the demands of a fast expanding world population. In this situation nuclear electricity will become more and more important and the known reserves of uranium would be consumed quite quickly by thermal reactors. It would be possible to sustain a large nuclear programme only by introducing fast reactors. One can conclude that there are strategic reasons for pursuing the development of fast breeder reactors. It will become desirable essential, to have this technology available for introduction. The experience of the various prototypes presently in operation has confirmed the operability and benign characteristics of the LMFR and has given ground for confidence in the future. Current fast reactor designs offer very large margins of safety and by virtue of redundant and diverse safety systems the potential for an energetic core disruptive accident or for fast reactor core meltdown has been essentially eliminated. Several international forums reviewed the current trends in the fast reactor development. The view was reaffirmed that fast breeder reactors still remain the most practical tool for effective utilization of uranium resources for the future energy needs. Achievement of competitiveness with LMRs is still the first priority condition for the future deployment of this type of reactor. The recycling of plutonium into LMFBRs would allow

Status of national programmes on fast breeder reactors. Twenty-fifth annual meeting of the International Working Group on Fast Reactors. Summary report. Working material

International Nuclear Information System (INIS)

1992-01-01

At present nuclear power accounts for approximately 17% of total electricity generation worldwide. Given continuing population growth and the needs of the third world and developing countries to improve their economic performance and standard of living, energy demand is expected to continue to grow through the 21st century. The proportion of energy supplied as electricity is also expected to continue to increase. Although fossil fuelled electricity generation is the option preferred by several countries for the short term, there are rising concerns over climatic consequences caused by extended burning of fossil fuels as a result of the demands of a fast expanding world population. In this situation nuclear electricity will become more and more important and the known reserves of uranium would be consumed quite quickly by thermal reactors. It would be possible to sustain a large nuclear programme only by introducing fast reactors. One can conclude that there are strategic reasons for pursuing the development of fast breeder reactors. It will become desirable essential, to have this technology available for introduction. The experience of the various prototypes presently in operation has confirmed the operability and benign characteristics of the LMFR and has given ground for confidence in the future. Current fast reactor designs offer very large margins of safety and by virtue of redundant and diverse safety systems the potential for an energetic core disruptive accident or for fast reactor core meltdown has been essentially eliminated. Several international forums reviewed the current trends in the fast reactor development. The view was reaffirmed that fast breeder reactors still remain the most practical tool for effective utilization of uranium resources for the future energy needs. Achievement of competitiveness with LMRs is still the first priority condition for the future deployment of this type of reactor. The recycling of plutonium into LMFBRs would allow

Power balance in an Ohmically heated fusion reactor

International Nuclear Information System (INIS)

Christiansen, J.P.; Roberts, K.V.

1982-01-01

A simplified power-balance equation (zero-dimensional model) is used to study the performance of an Ohmically heated fusion reactor with emphasis on a pulsed reversed-field pinch concept (RFP). The energy confinement time tausub(E) is treated as an adjustable function, and empirical tokamak scaling laws are employed in the numerical estimates, which are supplemented by 1-D ATHENE code calculations. The known heating rates and energy losses are represented by the net energy replacement time tausub(W), which is exhibited as a surface in density (n) and temperature (T) space with a saddle point (nsub(*), Tsub(*)), the optimum ignition point. It is concluded that i) ignition by Ohmic heating is more practicable for the RFP reactor than for a tokamak reactor with the same tausub(E), (ii) if at fixed current the minor radius can be reduced or at fixed minor radius the current can be increased, then it is found that Ohmic ignition becomes more likely when present tokamak scaling laws are used. More definitive estimates require, however, a knowledge of tausub(E), which can only be obtained by establishing a reliable set of experimental RFP scaling laws and, in particular, by extending RFP experiments closer to the reactor regime. (author)

Evaluación del comportamiento hidráulico en un reactor anaerobio de doble cámara (RADCA)

OpenAIRE

Nancy Rincón; Andres Galindo; Jhonny Pérez

2011-01-01

En la remoción de carga orgánica en un sistema de tratamiento de aguas residuales intervienen los procesos bioquímico y aspectos hidrodinámicos como las características de flujo, régimen de mezcla, tiempos de residencia, geometría del reactor, por otro lado las condiciones de flujo no ideal tales como cortos circuitos, zonas muertas y recirculación interna afectan su desempeño. En esta investigación se evaluó el comportamiento hidráulico de un reactor anaerobio de doble cámara (RADCA) de 5...

Assessment of Mass Fraction and Melting Temperature for the Application of Limestone Concrete and Siliceous Concrete to Nuclear Reactor Basemat Considering Molten Core–Concrete Interaction

Directory of Open Access Journals (Sweden)

Hojae Lee

2016-04-01

Full Text Available Severe accident scenarios in nuclear reactors, such as nuclear meltdown, reveal that an extremely hot molten core may fall into the nuclear reactor cavity and seriously affect the safety of the nuclear containment vessel due to the chain reaction caused by the reaction between the molten core and concrete. This paper reports on research focused on the type and amount of vapor produced during the reaction between a high-temperature molten core and concrete, as well as on the erosion rate of concrete and the heat transfer characteristics at its vicinity. This study identifies the mass fraction and melting temperature as the most influential properties of concrete necessary for a safety analysis conducted in relation to the thermal interaction between the molten core and the basemat concrete. The types of concrete that are actually used in nuclear reactor cavities were investigated. The H2O content in concrete required for the computation of the relative amount of gases generated by the chemical reaction of the vapor, the quantity of CO2 necessary for computing the cooling speed of the molten core, and the melting temperature of concrete are evaluated experimentally for the molten core–concrete interaction analysis.

E Günıster

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. E Günıster. Articles written in Bulletin of Materials Science. Volume 27 Issue 3 June 2004 pp 317-322 Surfactants. Effect of sodium dodecyl sulfate on flow and electrokinetic properties of Na-activated bentonite dispersions · E Günıster S İşçı A Alemdar N Güngör · More Details ...

E-PROCUREMENT: IMPORTANCIA Y APLICACIÓN

Directory of Open Access Journals (Sweden)

Isabel Fernández Quesada

2003-04-01

Full Text Available En el trabajo se aborda uno de los aspectos externos del e-business: el e-procurement. Se valora la importancia de la utilización de la red en general y en la función logística y de compras, en particular. Partiendo de las actividades tradicionales de compras, se explicitan las ventajas que supone respecto a ellas el e-procurement y la importancia estratégica de su aplicación. Asimismo, se profundiza en el propio concepto de e-procurement y en su arquitectura desde el punto de vista de su implantación empresarial.

Nuclear reactor

International Nuclear Information System (INIS)

Hattori, Sadao; Sato, Morihiko.

1994-01-01

Liquid metals such as liquid metal sodium are filled in a reactor container as primary coolants. A plurality of reactor core containers are disposed in a row in the circumferential direction along with the inner circumferential wall of the reactor container. One or a plurality of intermediate coolers are disposed at the inside of an annular row of the reactor core containers. A reactor core constituted with fuel rods and control rods (module reactor core) is contained at the inside of each of the reactor core containers. Each of the intermediate coolers comprises a cylindrical intermediate cooling vessels. The intermediate cooling vessel comprises an intermediate heat exchanger for heat exchange of primary coolants and secondary coolants and recycling pumps for compulsorily recycling primary coolants at the inside thereof. Since a plurality of reactor core containers are thus assembled, a great reactor power can be attained. Further, the module reactor core contained in one reactor core vessel may be small sized, to facilitate the control for the reactor core operation. (I.N.)

Very high flux steady state reactor and accelerator based sources

International Nuclear Information System (INIS)

Ludewig, H.; Todosow, M.; Simos, N.; Shapiro, S.; Hastings, J.

2004-01-01

With the number of steady state neutron sources in the US declining (including the demise of the Bnl HFBR) the remaining intense sources are now in Europe (i.e. reactors - ILL and FMR, accelerator - PSI). The intensity of the undisturbed thermal flux for sources currently in operation ranges from 10 14 n/cm 2 *s to 10 15 n/cm 2 *s. The proposed Advanced Neutron Source (ANS) was to be a high power reactor (about 350 MW) with a projected undisturbed thermal flux of 7*10 15 n/cm 2 *s but never materialized. The objective of the current study is to explore the requirements and implications of two source concepts with an undisturbed flux of 10 16 n/cm 2 *s. The first is a reactor based concept operating at high power density (10 MW/l - 15 MW/l) and a total power of 100 MW - 250 MW, depending on fissile enrichment. The second is an accelerator based concept relying on a 1 GeV - 1.5 GeV proton Linac with a total beam power of 40 MW and a liquid lead-bismuth eutectic target. In the reactor source study, the effects of fissile material enrichment, coolant temperature and pressure drop, and estimates of pressure vessel stress levels will be investigated. The fuel form for the reactor will be different from all other operating source reactors in that it is proposed to use an infiltrated graphitic structure, which has been developed for nuclear thermal propulsion reactor applications. In the accelerator based source the generation of spallation products and their activation levels, and the material damage sustained by the beam window will be investigated. (authors)

Neutronics conceptual design of the innovative research reactor core using uranium molybdenum fuel

International Nuclear Information System (INIS)

Tukiran S; Surian Pinem; Tagor MS; Lily S; Jati Susilo

2012-01-01

The multipurpose of research reactor utilization make many countries build the new research reactor. Trend of this reactor for this moment is multipurpose reactor type with a compact core to get high neutron flux at the low or medium level of power. The research newest. Reactor in Indonesia right now is already 25 year old. Therefore, it is needed to design a new research reactor, called innovative research reactor (IRR) and then as an alternative to replace the old research reactor. The aim of this research is to get the optimal configuration of equilibrium core with the acceptance criteria are minimum thermal neutron flux is 2.5E14 n/cm 2 s at the power level of 20 MW (minimum), length of cycle of more than 40 days, and the most efficient of using fuel in the core. Neutronics design has been performed for new fuel of U-9Mo-AI with various fuel density and reflector. Design calculation has been performed using WIMSD-5B and BATAN-FUEL computer codes. The calculation result of the conceptual design shows four core configurations namely 5x5, 5x7, 6x5 and 6x6. The optimalization result for equilibrium core of innovative research reactor is the 5x5 configuration with 450 gU fuel loading, berilium reflector, maximum thermal neutron flux at reflector is 3.33E14 n/cm 2 sand length of cycle is 57 days is the most optimal of IRR. (author)

Spectrometer requirements for (e,e'2N) studies

International Nuclear Information System (INIS)

Lightbody, J.W. Jr.

1981-01-01

One specific experiment that may be performed with a future CW accelerator is a study of (e,e'2N) reactions through which we may learn details of the short range interaction of two nucleons within nuclear matter. It is suspected that the only mechanism which can lead to the observed high momentum components in the single nucleon momentum distribution (above approx. 400 MeV/c) inferred from (e,e'p) and (γ,p) measurements is the presence of short-range few-body correlations in the many-body nuclear wave function. It is expected that the explicit pair correlation function may be inferred from relative two-nucleon momentum distributions measured in (e,e'2N) experiments. It is therefore interesting to estimate counting rates using measured one-body momentum distributions to see what types of spectrometers are required

Reactor Dosimetry State of the Art 2008

Science.gov (United States)

Voorbraak, Wim; Debarberis, Luigi; D'Hondt, Pierre; Wagemans, Jan

2009-08-01

Oral session 1: Retrospective dosimetry. Retrospective dosimetry of VVER 440 reactor pressure vessel at the 3rd unit of Dukovany NPP / M. Marek ... [et al.]. Retrospective dosimetry study at the RPV of NPP Greifswald unit 1 / J. Konheiser ... [et al.]. Test of prototype detector for retrospective neutron dosimetry of reactor internals and vessel / K. Hayashi ... [et al.]. Neutron doses to the concrete vessel and tendons of a magnox reactor using retrospective dosimetry / D. A. Allen ... [et al.]. A retrospective dosimetry feasibility study for Atucha I / J. Wagemans ... [et al.]. Retrospective reactor dosimetry with zirconium alloy samples in a PWR / L. R. Greenwood and J. P. Foster -- Oral session 2: Experimental techniques. Characterizing the Time-dependent components of reactor n/y environments / P. J. Griffin, S. M. Luker and A. J. Suo-Anttila. Measurements of the recoil-ion response of silicon carbide detectors to fast neutrons / F. H. Ruddy, J. G. Seidel and F. Franceschini. Measurement of the neutron spectrum of the HB-4 cold source at the high flux isotope reactor at Oak Ridge National Laboratory / J. L. Robertson and E. B. Iverson. Feasibility of cavity ring-down laser spectroscopy for dose rate monitoring on nuclear reactor / H. Tomita ... [et al.]. Measuring transistor damage factors in a non-stable defect environment / D. B. King ... [et al.]. Neutron-detection based monitoring of void effects in boiling water reactors / J. Loberg ... [et al.] -- Poster session 1: Power reactor surveillance, retrospective dosimetry, benchmarks and inter-comparisons, adjustment methods, experimental techniques, transport calculations. Improved diagnostics for analysis of a reactor pulse radiation environment / S. M. Luker ... [et al.]. Simulation of the response of silicon carbide fast neutron detectors / F. Franceschini, F. H. Ruddy and B. Petrović. NSV A-3: a computer code for least-squares adjustment of neutron spectra and measured dosimeter responses / J. G

Characteristics of a novel nanosecond DBD microplasma reactor for flow applications

Science.gov (United States)

Elkholy, A.; Nijdam, S.; van Veldhuizen, E.; Dam, N.; van Oijen, J.; Ebert, U.; de Goey, L. Philip H.

2018-05-01

We present a novel microplasma flow reactor using a dielectric barrier discharge (DBD) driven by repetitive nanosecond high-voltage pulses. Our DBD-based geometry can generate a non-thermal plasma discharge at atmospheric pressure and below in a regular pattern of micro-channels. This reactor can work continuously up to about 100 min in air, depending on the pulse repetition rate and operating pressure. We here present the geometry and main characteristics of the reactor. Pulse energies of 1.46 and 1.3 μJ per channel at atmospheric pressure and 50 mbar, respectively, have been determined by time-resolved measurements of current and voltage. Time-resolved optical emission spectroscopy measurements have been performed to calculate the relative species concentrations and temperatures (vibrational and rotational) of the discharge. The effects of the operating pressure and flow velocity on the discharge intensity have been investigated. In addition, the effective reduced electric field strength {(E/N)}eff} has been obtained from the intensity ratio of vibronic emission bands of molecular nitrogen at different operating pressures and different locations. The derived {(E/N)}eff} increases gradually from about 550 to 4600 Td when decreasing the pressure from 1 bar to 100 mbar. Below 100 mbar, further pressure reduction results in a significant increase in {(E/N)}eff} up to about 10000 Td at 50 mbar.

White emission by self-regulated growth of InGaN/GaN quantum wells on in situ self-organized faceted n-GaN islands

International Nuclear Information System (INIS)

Fang Zhilai

2011-01-01

The in situ self-organization of three-dimensional n-GaN islands of distinct sidewall faceting was realized by initial low V/III ratio growth under high reactor pressure followed by variations of the V/III ratio and reactor pressure. The naturally formed faceted islands with top and sidewall facets of various specific polar angles may serve as an ideal template for self-regulated growth of the InGaN/GaN multiple quantum wells (MQWs), i.e. the growth behavior is specific polar angle dependent. Further, the growth behavior and luminescence properties of the InGaN/GaN MQWs on various facets of different specific polar angles are directly compared and discussed. Tetrachromatic white emissions (blue, cyan, green, and red) from single-chip phosphor-free InGaN/GaN MQWs are realized by color tuning through island shaping, shape variations, and self-regulated growth of the InGaN/GaN MQWs.

Performance evaluation of 24 ion exchange materials for removing cesium and strontium from actual and simulated N-Reactor storage basin water

Energy Technology Data Exchange (ETDEWEB)

Brown, G.N.; Carson, K.J.; DesChane, J.R.; Elovich, R.J.

1997-09-01

This report describes the evaluation of 24 organic and inorganic ion exchange materials for removing cesium and strontium from actual and simulated waters from the 100 Area 105 N-Reactor fuel storage basin. The data described in this report can be applied for developing and evaluating ion exchange pre-treatment process flowsheets. Cesium and strontium batch distribution ratios (K{sub d}`s), decontamination factors (DF), and material loadings (mmol g{sup -1}) are compared as a function of ion exchange material and initial cesium concentration. The actual and simulated N-Basin waters contain relatively low levels of aluminum, barium, calcium, potassium, and magnesium (ranging from 8.33E-04 to 6.40E-05 M), with slightly higher levels of boron (6.63E-03 M) and sodium (1.62E-03 M). The {sup 137}Cs level is 1.74E-06 Ci L-{sup 1} which corresponds to approximately 4.87E-10 M Cs. The initial Na/Cs ratio was 3.33E+06. The concentration of total strontium is 4.45E-06 M, while the {sup 90}Sr radioactive component was measured to be 6.13E-06 Ci L{sup -1}. Simulant tests were conducted by contacting 0.067 g or each ion exchange material with approximately 100 mL of either the actual or simulated N-Basin water. The simulants contained variable initial cesium concentrations ranging from 1.00E-04 to 2.57E- 10 M Cs while all other components were held constant. For all materials, the average cesium K{sub d} was independent of cesium concentration below approximately 1.0E-06 M. Above this level, the average cesium K{sub d} values decreased significantly. Cesium K{sub d} values exceeding 1.0E+07 mL g{sup -1} were measured in the simulated N-Basin water. However, when measured in the actual N-Basin water the values were several orders of magnitude lower, with a maximum of 1.24E+05 mL g{sup -1} observed.

Nuclear reactor

International Nuclear Information System (INIS)

Schulze, I.; Gutscher, E.

1980-01-01

The core contains a critical mass of UN or U 2 N 3 in the form of a noncritical solution with melted Sn being kept below a N atmosphere. The lining of the reactor core consists of graphite. If fission progresses part of the melted metal solution is removed and cleaned from fission products. The reactor temperatures lie in the range of 300 to 2000 0 C. (Examples and tables). (RW) [de

Low drift type N thermocouples in out-of-pile advanced gas reactor mock-up test: metallurgical analysis

International Nuclear Information System (INIS)

Scervini, M.; Palmer, J.; Haggard, D.C.; Swank, W.D.

2015-01-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. They are crucial for the control of current nuclear reactors and for the development of GEN IV reactors. In nuclear applications thermocouples are strongly affected by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition and, as a consequence, a time dependent drift of the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. Previous experiences with type K thermocouples in nuclear reactors have shown that they are affected by neutron irradiation only to a limited extent. Similarly type N thermocouples are expected to be only slightly affected by neutron fluxes. Currently the use of Nickel based thermocouples is limited to temperatures lower than 1000 deg. C due to drift related to phenomena other than nuclear irradiation. As part of a collaboration between Idaho National Laboratory (INL) and the University of Cambridge a variety of Type N thermocouples have been exposed at INL in an Advanced Gas Reactor mock-up test at 1150 deg. C for 2000 h, 1200 deg. C for 2000 h, 125 deg. C for 200 h and 1300 deg. C for 200 h, and later analysed metallurgically at the University of Cambridge. The use of electron microscopy allows to identify the metallurgical changes occurring in the thermocouples during high temperature exposure and correlate the time dependent thermocouple drift with the microscopic changes experienced by the thermoelements of different thermocouple designs. In this paper conventional Inconel 600 sheathed type N thermocouples and a type N using a customized sheath developed at the University of

Low drift type N thermocouples in out-of-pile advanced gas reactor mock-up test: metallurgical analysis

Energy Technology Data Exchange (ETDEWEB)

Scervini, M. [University of Cambridge, Department of Materials Science and Metallurgy, 27 Charles Babbage Road, CB30FS Cambridge, (United Kingdom); Palmer, J.; Haggard, D.C.; Swank, W.D. [Idaho National Laboratory, Idaho Falls, ID 83415-3840, (United States)

2015-07-01

Thermocouples are the most commonly used sensors for temperature measurement in nuclear reactors. They are crucial for the control of current nuclear reactors and for the development of GEN IV reactors. In nuclear applications thermocouples are strongly affected by intense neutron fluxes. As a result of the interaction with neutrons, the thermoelements of the thermocouples undergo transmutation, which produces a time dependent change in composition and, as a consequence, a time dependent drift of the thermocouple signal. Thermocouple drift can be very significant for in-pile temperature measurements and may render the temperature sensors unreliable after exposure to nuclear radiation for relatively short times compared to the life required for temperature sensors in nuclear applications. Previous experiences with type K thermocouples in nuclear reactors have shown that they are affected by neutron irradiation only to a limited extent. Similarly type N thermocouples are expected to be only slightly affected by neutron fluxes. Currently the use of Nickel based thermocouples is limited to temperatures lower than 1000 deg. C due to drift related to phenomena other than nuclear irradiation. As part of a collaboration between Idaho National Laboratory (INL) and the University of Cambridge a variety of Type N thermocouples have been exposed at INL in an Advanced Gas Reactor mock-up test at 1150 deg. C for 2000 h, 1200 deg. C for 2000 h, 125 deg. C for 200 h and 1300 deg. C for 200 h, and later analysed metallurgically at the University of Cambridge. The use of electron microscopy allows to identify the metallurgical changes occurring in the thermocouples during high temperature exposure and correlate the time dependent thermocouple drift with the microscopic changes experienced by the thermoelements of different thermocouple designs. In this paper conventional Inconel 600 sheathed type N thermocouples and a type N using a customized sheath developed at the University of

Flowsheet for shear/leach processing of N Reactor fuel at PUREX

International Nuclear Information System (INIS)

Enghusen, M.B.

1995-01-01

This document was originally prepared to support the restart of the PUREX plant using a new Shear/Leach head end process. However, the PUREX facility was shutdown and processing of the remaining N Reactor fuel is no longer considered an alternative for fuel disposition. This document is being issued for reference only to document the activities which were investigated to incorporate the shear/leach process in the PUREX plant

Neutron beam facilities at the Australian Replacement Research Reactor

International Nuclear Information System (INIS)

Kennedy, Shane; Robinson, Robert; Hunter, Brett

2001-01-01

Australia is building a research reactor to replace the HIFAR reactor at Lucas Heights by the end of 2005. Like HIFAR, the Replacement Research Reactor will be multipurpose with capabilities for both neutron beam research and radioisotope production. It will be a pool-type reactor with thermal neutron flux (unperturbed) of 4 x 10 14 n/cm 2 /sec and a liquid D 2 cold neutron source. Cold and thermal neutron beams for neutron beam research will be provided at the reactor face and in a large neutron guide hall. Supermirror neutron guides will transport cold and thermal neutrons to the guide hall. The reactor and the associated infrastructure, with the exception of the neutron beam instruments, is to be built by INVAP S.E. under contract. The neutron beam instruments will be developed by ANSTO, in consultation with the Australian user community. This status report includes a review the planned scientific capabilities, a description of the facility and a summary of progress to date. (author)

"Wandering in the Desert": The Clinch River Breeder Reactor Debate in the U.S. Congress, 1972-1983.

Science.gov (United States)

Camp, Michael

2018-01-01

The experimental Clinch River breeder reactor, approved by the U.S. Congress in 1970 for construction in East Tennessee, would have used plutonium instead of uranium. The project drew the ire of environmentalists who insisted that plutonium was too dangerous for commercial use, along with opponents of nuclear proliferation. Tennessee's representatives in Congress, however, desired the jobs that the project would create, and formed legislative coalitions to ensure continued appropriations for the project. Funding lasted until 1983, when fiscal conservatives, concerned about ballooning cost projections, joined with environmentalists to defund the breeder. Interpretations of U.S. nuclear policy in the 1980s have often revolved around the Three Mile Island meltdown's aftermath, but Clinch River was not affected by the incident. Instead, the Clinch River controversy revolved around other unrelated issues. The Clinch River story therefore offers a corrective to accounts that privilege national public opinion at the expense of other variables.

Neutronic analysis concerning the utilization of mixed U N-Pu N nitride fuel for fast reactors

International Nuclear Information System (INIS)

Renke, C.A.C.; Batista, J.L.; Waintraub, M.; Santos Bastos, W. dos; Brito Aghina, L.O. de.

1991-08-01

Neutronic behavior of mixed UN-PuN nitride fuel in substitution of the mixed oxide U O 2 - Pu O 2 for fast reactors is discussed with focus on Super Phenix I. Characteristics parameters of both cores are calculated and compared and the results presented show a great advantage for the nitride fuel, pointing out a larger performance of fuel elements in the core and an effective reduction of reactivity loss during the cycle. (author)

Waste conversion into n-caprylate and n-caproate: resource recovery from wine lees using anaerobic reactor microbiomes and in-line extraction

Directory of Open Access Journals (Sweden)

Leo A. Kucek

2016-11-01

Full Text Available To convert wastes into sustainable liquid fuels and chemicals, new resource recovery technologies are required. Chain elongation is a carboxylate-platform bioprocess that converts short-chain carboxylates (SCCs (e.g., acetate C2 and n-butyrate C4 into medium-chain carboxylates (MCCs (e.g., n-caprylate C8 and n-caproate C6 with hydrogen gas as a side product. Ethanol or another electron donor (e.g., lactate, carbohydrate is required. Competitive MCC productivities, yields (product vs. substrate fed, and specificities (product vs. all products were only achieved previously from an organic waste material when exogenous ethanol had been added. Here, we converted a real organic waste, which inherently comprised of ethanol, into MCCs with n-caprylate as the target product. We used wine lees, which consisted primarily of settled yeast cells and ethanol from wine fermentation, and produced MCCs with a reactor microbiome. We operated the bioreactor at a pH of 5.2 and with continuous in-line extraction and achieved a MCC productivity of 3.9 g COD/L-d at an organic loading rate of 5.8 g COD/L-d, resulting in a promising MCC yield of 67% and specificities of 36% for each n-caprylate and n-caproate (72% for both. Compared to all other studies that used complex organic substrates, we achieved the highest n-caprylate-to-n-caproate product ratio of 1.0 (COD basis, because we used increased broth-recycle rates through the forward membrane contactor, which improved in-line extraction rates. Increased recycle rates also allowed us to achieve the highest reported MCC production flux per membrane surface area thus far (20.1 g COD/m2-d. Through microbial community analyses, we determined that an operational taxonomic unit (OTU for Bacteroides spp. was dominant and was positively correlated with increased MCC productivities. Our data also suggested that the microbiome may have been shaped for improved MCC production by the high broth-recycle rates. Comparable abiotic

Heterogeneous reactors

International Nuclear Information System (INIS)

Moura Neto, C. de; Nair, R.P.K.

1979-08-01

The microscopic study of a cell is meant for the determination of the infinite multiplication factor of the cell, which is given by the four factor formula: K(infinite) = n(epsilon)pf. The analysis of an homogeneous reactor is similar to that of an heterogeneous reactor, but each factor of the four factor formula can not be calculated by the formulas developed in the case of an homogeneous reactor. A great number of methods was developed for the calculation of heterogeneous reactors and some of them are discussed. (Author) [pt

Production reactor productivity improvement plan

International Nuclear Information System (INIS)

Leitz, E.E.

1980-01-01

The N Reactor complex, which is operated by UNC for DOE, is a unique facility and as such it is difficult to transfer technological developments and management innovations directly to the N Reactor operations. Therefore the approach to implementing an effective program was to start with the general systems philosophy and then progress into using those specific analytical and management techniques applicable to the unique situation (technologically and administratively) which existed at the N Reactor plant

n-Heptane cool flame chemistry: Unraveling intermediate species measured in a stirred reactor and motored engine

KAUST Repository

Wang, Zhandong

2017-10-03

This work identifies classes of cool flame intermediates from n-heptane low-temperature oxidation in a jet-stirred reactor (JSR) and a motored cooperative fuel research (CFR) engine. The sampled species from the JSR oxidation of a mixture of n-heptane/O2/Ar (0.01/0.11/0.88) were analyzed using a synchrotron vacuum ultraviolet radiation photoionization (SVUV-PI) time-of-flight molecular-beam mass spectrometer (MBMS) and an atmospheric pressure chemical ionization (APCI) Orbitrap mass spectrometer (OTMS). The OTMS was also used to analyze the sampled species from a CFR engine exhaust. Approximately 70 intermediates were detected by the SVUV-PI-MBMS, and their assigned molecular formulae are in good agreement with those detected by the APCI-OTMS, which has ultra-high mass resolving power and provides an accurate elemental C/H/O composition of the intermediate species. Furthermore, the results show that the species formed during the partial oxidation of n-heptane in the CFR engine are very similar to those produced in an ideal reactor, i.e., a JSR.The products can be classified by species with molecular formulae of C7H14Ox (x = 0–5), C7H12Ox (x = 0–4), C7H10Ox (x = 0–4), CnH2n (n = 2–6), CnH2n−2 (n = 4–6), CnH2n+2O (n = 1–4), CnH2nO (n = 1–6), CnH2n−2O (n = 2–6), CnH2n−4O (n = 4–6), CnH2n+2O2 (n = 0–4, 7), CnH2nO2 (n = 1–6), CnH2n−2O2 (n = 2–6), CnH2n−4O2 (n = 4–6), and CnH2nO3 (n = 3–6). The identified intermediate species include alkenes, dienes, aldehyde/keto compounds, olefinic aldehyde/keto compounds, diones, cyclic ethers, peroxides, acids, and alcohols/ethers. Reaction pathways forming these intermediates are proposed and discussed herein. These experimental results are important in the development of more accurate kinetic models for n-heptane and longer-chain alkanes.

Characterization of a fast to thermal neutron spectrum converter on PROSPERO reactor

Energy Technology Data Exchange (ETDEWEB)

Jacquet, X.; Authier, N.; Casoli, P.; Combacon, S. [CEA, Valduc Center, 21120 Is sur Tille (France); Calzavarra, Y. [ILL, Institut Laue Langevin, 38000 Grenoble (France)

2009-07-01

The PROSPERO reactor is located at CEA Valduc Center in France. The reactor is composed of an internal core made of High Enriched Uranium metal alloy surrounded by a reflector of depleted uranium. The reactor is used as a fast neutron spectrum source and is operated in delayed critical state with a continuous and steady power for several hours, which can vary from 3 mW to 3 kW, which is the nominal power. The flux at nominal power varies from 5.10{sup +10} n.cm{sup -2}/s at the reflector surface to 10{sup +7} n.cm{sup -2}/s at 5 meters from reactor axis. It has been decided to build a neutron energy converter allowing the production of a neutron thermal spectrum. As the core produces fast neutrons spectrum, we built a hollow cubic box of 50 cm x 50 cm x 50 cm with 10-cm-thick polyethylene bricks and placed one meter away from central reactor axis to moderate as much as possible neutrons to lower energies (E<0.6 eV). Analysis of the moderated flux inside the converter was performed using different activation foils such as indium or gold. We have developed a model of the experiment in the Monte Carlo neutron transport code TRIPOLI-4. A non-analogous transport calculation scheme was necessary to reproduce properly the experimental activities. The results of the calculated activations are within 4% of the experimental measurements given with 10% uncertainty (2 sigma). We show that the converter realizes thermalization of 80 % of the PROSPERO reactor fast neutrons below the cadmium threshold of 0.6 eV. Epithermal neutrons represent 15% of the spectrum and only 5% are in the fast neutron range above 1 MeV. The total flux at the center of the converter is 1.4 10{sup +9} n.cm{sup -2}/s at 3000 W

Numerical predictions of natural convection in a uniformly heated pool

International Nuclear Information System (INIS)

Tzanos, C.P.; Cho, D.H.

1993-01-01

In the event of a core meltdown accident, one of the accident progression paths is fuel relocation to the lower reactor plenum. In the heavy-water new production reactor (NPR-HWR) design, the reactor cavity is flooded with water. In such a design, decay heat removal to the water in the reactor cavity and thence to the containment may be adequate to keep the reactor vessel temperature below failure limits. If this is the case, the accident progression can be arrested by retaining a coolable corium configuration in the lower reactor plenum. The strategy of reactor cavity flooding to prevent reactor vessel failure from molten corium relocation to the reactor vessel lower head has also been considered for commercial pressurized water reactors

Towards nuclear fusion reactors

International Nuclear Information System (INIS)

1993-11-01

The results of nuclear fusion researches in JAERI are summarized. In this report, following themes are collected: the concept of fusion reactor (including ITER), fusion reactor safety, plasma confinement, fusion reactor equipment, and so on. Includes glossary. (J.P.N.)

Commissioning of the Opal reactor cold neutron source

International Nuclear Information System (INIS)

Thiering, R.; Lu, W.; Ullah, R.

2006-01-01

Full text: At OPAL, Australia's first cold neutron facility will form an essential part of the reactor's research programs. Fast neutrons, born in the core of a reactor, interact with a cryogenic material, in this case liquid deuterium, to give them very low energies ( 1 0 m eV). A cold neutron flux of 1.4 1 0 E 1 4 n /cm 2/ s is expected, with a peak in the energy spectrum at 4.2m eV. The cold neutron source reached cryogenic conditions for the first time in late 2005. The cold neutron source operates with a sub-cooled liquid Deuterium moderator at 24 K. The moderator chamber, which contains the deuterium, has been constructed from AlMg 5. The thermosiphon and moderator chamber are cooled by helium gas, in a natural convection thermosiphon loop. The helium refrigeration system utilises the Brayton cycle, and is fully insulated within a high vacuum environment. Despite the proximity of the cold neutron source to the reactor core, it has been considered as effectively separate to the reactor system, due to the design of its special vacuum containment vessel. As OPAL is a multipurpose research reactor, used for beam research as well as radiopharmaceutical production and industrial irradiations, the cold neutron source has been designed with a stand-by mode, to maximise production. The stand-by mode is a warm operating mode using only gaseous deuterium at ambient temperatures (∼ 3 00 K ), allowing for continued reactor operations whilst parts of the cold source are unavailable or in maintenance. This is the first time such a stand-by feature has been incorporated into a cold source facility

Water reactor fuel behaviour and fission products release in off-normal and accident conditions

International Nuclear Information System (INIS)

1987-09-01

The present meeting was scheduled by the International Atomic Energy Agency upon the proposal of the Members of the International Working Group on Water Reactor Fuel Performance and Technology and held at the IAEA Headquarters in Vienna from 10 to 13 November 1986. Thirty participants from 17 countries and an international organization attended the meeting. Eighteen papers were presented from 13 countries and one international organization. The meeting was composed of four sessions and covered subjects related to: physico-chemical properties of core materials under off-normal conditions, and their interactions up to and after melt-down (5 papers); core materials deformation, relocation and core coolability under (severe) accident conditions (4 papers); fission products release: including experience, mechanisms and modelling (5 papers); power plant experience (4 papers). A separate abstract was prepared for each of these 18 papers. Four working groups covering the above-mentioned topics were held to discuss the present status of the knowledge and to develop recommendations for future activities in this field. Refs, figs and tabs

Neutron capture cross section measurement of 238U at the n TOF CERN facility with C6D6 scintillation detectors in the energy region from 1 eV to 700 keV

CERN Document Server

Mingrone, F.

2017-01-01

The aim of this work is to provide a precise and accurate measurement of the 238U(n,g) reaction cross section in the energy region from 1 eV to 700 keV. This reaction is of fundamental importance for the design calculations of nuclear reactors, governing the behaviour of the reactor core. In particular, fast reactors, which are experiencing a growing interest for their ability to burn radioactive waste, operate in the high energy region of the neutron spectrum. In this energy region most recent evaluations disagree due to inconsistencies in the existing measurements of up to 15%. In addition, the assessment of nuclear data uncertainty performed for innovative reactor systems shows that the uncertainty in the radiative capture cross-section of 238U should be further reduced to 1-3% in the energy region from 20 eV to 25 keV. To this purpose, addressed by the Nuclear Energy Agency as a priority nuclear data need, complementary experiments, one at the GELINA and two at the n_TOF facility, were proposed and carrie...

PIK reactor construction status

International Nuclear Information System (INIS)

Konoplev, K.A.; Smolsky, S.L.

2001-01-01

The 100MW reactor PIK for fundamental researches has a thermal neutron flux of more than 10 15 n/cm 2 sec. This presentation outlines the construction state as of 2001, its prospects and completion tactics in the conditions of unstable finance. Construction of the reactor started in 1976. In 1986 construction of the building was completed and significant part of the installation work fulfilled. Construction of cooling systems was finished, the control panel assembled, and adjustment of the pump and gate valve control circuits started. After Chernobyl catastrophe, the USSR nuclear reactor safety requirements were revised. The PIK design did not meet these requirements and underwent considerable revision. The reconstruction design resulted in double the initial cost. Creation of the containment was the bulkiest part of the reconstruction. It brought about the need to disassemble the roofing of the building, dismantle all the equipment of the two upper floors, and lay up the equipment of the lower floors. As of 2001, construction in accordance with the revised design is at the stage of assemblage of the most important units, i.e. reactor itself, cooling system, heavy water system, and a number of auxiliary systems, such as depleted fuel storage, emergency cooling system etc. (orig.)

Middle English Preposition Twēn(E

Directory of Open Access Journals (Sweden)

Ciszek-Kiliszewska Ewa

2014-12-01

Full Text Available The present paper focuses on the Middle English preposition twēn(e ‘between, among, in between’. The aim of the study is to review the acknowledged etymology of twēn(e as well as to provide its semantics, dialect distribution, complete textual distribution (record of texts employing twēn(e, and absolute token frequency. Moreover, all texts including the preposition twēn(e are subject to an analysis of the whole variety of prepositions meaning ‘between’ and their token frequency in order to establish the proportions of the use of twēn(e and other discussed prepositions, especially the better established preposition betwēn(e in texts employing twēn(e. The study is based on such extensive electronic databases as the Middle English Dictionary online, the Oxford English Dictionary online and the Corpus of Middle English Prose and Verse as well as on a number of complete Middle English texts. The study of the corpus demonstrates the presence of twēn(e and other prepositions meaning ‘between’ also in texts not listed by the Middle English Dictionary online or the Oxford English Dictionary online under appropriate entries, and thus helps to provide a more complete record of texts and authors utilizing twēn(e and the extent of use of twēn(e as compared to other prepositions meaning ‘between’. Moreover, the study demonstrates that also the other discussed prepositions are often not recorded in particular texts by the MED online or the OED online. In more general terms, the paper points out the need for the use of complete texts for the study of historical prepositions.

Potential applications of NbN composites in fusion reactor magnets

International Nuclear Information System (INIS)

Capone, D.W. II; Gray, K.E.; Kampwirth, R.T.; Ho, H.L.

1986-02-01

Recent projected requirements for large scale fusion reactor magnets call for the development of advanced superconducting materials capable of producing peak magnetic fields in excess of 15 T with current densities in the windings in excess of 2 x 10 3 A/cm 2 . These materials will be exposed to large stresses (up to 500 MPa) and neutron fluences as high as 10 22 n/cm 2 over the lifetime of the conductor. The demonstrated strain and radiation tolerance of NbN together with excellent superconducting properties make it a promising candidate to be used in a superconducting composite capable of satisfying these requirements. Our program at Argonne is directed towards demonstrating a method of fabrication which is capable of achieving these goals. Tests will be conducted on moderate lengths of NbN superconducting composites to verify the ability to achieve large overall current densities in magnetic fields up to 20 T. High field applications of NbN are also being investigated by groups in Japan and Germany

Safety oriented LWR research. Annual report 1990

International Nuclear Information System (INIS)

1991-07-01

The contributions describe phenomenons of severe fuel damage and aspects of core meltdown accidents. These accidents deal with aerosol behaviour and ventilation systems and the methods for assessing and reducing the radiological concequences of nuclear accidents. Other contributions describe selected questions of safety of HCLWR type reactors. (DG)

Location sites for nuclear power plants and the public drinking water supplies

International Nuclear Information System (INIS)

1987-05-01

This report presents the results of a study by the Dutch RIWA- Working Group Nuclear Power Plants, of the possible effects of a nuclear-reactor melt-down accident upon the drinking-water supply in the Netherlands which is dependent on surface waters. The aim of this report is to contribute to the 're-consideration with regard to siting of nuclear power plants' of the Dutch government. In the case of a nuclear-reactor melt-down accident in the Netherlands or directly adjacent countries, surface waters destined for drinking-water production may be contaminated severely. The amount of contamination depends, among other things, upon the distance, wind direction, dry as well as wet deposition and the features of the place yielding drinking water. From calculations of contamination of surface waters in the case of open- supply build up it appears that the derived norm of the radionuclide cocktail may be exceeded for a period of weeks up to several months or even years. There are reasons to draw the same conclusion for supply build up in the dunes by means of surface infiltration in the dunes. A melt-down accident can cause very severe contamination. Also here it can be stated that, in the case of a calamity in the Netherlands or directly adjacent countries, a norm transgression may occur for weeks up to years. In view of the risks which nuclear power plants can hold for the drinking-water supply which depends upon surface-waters as basis element. Severe objections should be made with respect to the siting of nuclear power plants in the Netherlands unless the occurrence of melt-down accidents could be excluded. 11 refs.; 4 figs.; 7 tabs

Method of avoiding hazards resulting from accidents in water-cooled nuclear reactors

International Nuclear Information System (INIS)

Dorner, S.; Schretzmann, K.; Schumacher, G.

1984-01-01

In water-cooled reactors, e.g. BWRs and PWRs, elemental hydrogen is released by hydrolysis (in-leakage). In case of an accident in these reactors or at emergency cooling of e.g., a gas-cooled reactor with water additional hydrogen is produced by chemical reactions of the water with the cladding material. In order to prevent hydrogen pressurizing and the formation of a detonating gas mixture, dry powder containers are provided for in the endangered compartments of the reactor. In case of danger powdered CuO, MnO 2 , Fe 2 O 3 , or CdO, the oxygen content of which recombines with the hydrogen, is ejected from them. In addition, an extinguishing substance with an anticatalytic resp. inhibition effect and/or an inert gas of the group N 2 , He, Ar, CO 2 may be admixed to the powder resp. powder mixture. (orig./PW)

A report of the overall working group of the AEC Committee on Development of Advanced Power Reactors

International Nuclear Information System (INIS)

1979-01-01

The AEC Committee on Development of Advanced Power Reactors was set up in April, 1978, following on the previous AEC Special Committee on Development of Advanced Power Reactors, in order to study on the complementary power reactors between current LWRs and future FBRs. The subjects of study by the overall working group are the status of advanced power reactors in views of the nuclear fuel cycle, the impacts on industries, the selection of reactor types under present international circumstances, and the evaluation of advanced power reactors in their technology and economy. The following matters are described: evaluations in view of the nuclear fuel cycle, i.e. the features of the ATR of Japan and CANDU reactors of Canada; international problems concerning nuclear nonproliferation and securing of uranium; problems in the diversification of power reactor types concerning the expenditure and technology; problems of technology in the ATR of Japan, CANDU reactors of Canada and Pu utilization for LWRs; and the economy of D 2 O power reactors, i.e. the ATR of Japan and CANDU reactors of Canada. (J.P.N.)

Producción de hidrógeno a partir del tratamiento anaerobio de vinazas en un reactor UASB

Directory of Open Access Journals (Sweden)

César González-Ugalde

2014-09-01

Bajo condiciones mesofílicas (37 °C, un pH de operación de aproximadamente 5,50, una concentración del sustrato de 20 000 mg DQO/L y un tiempo de retención hidráulica (TRH de seis horas, la producción promedio de hidrógeno obtenida en el reactor UASB fue de 1,68 mL H2/h/L, con una tasa máxima de 13,4 mL H2/h/L. El porcentaje de remoción de DQO en el proceso de fermentación alcanzó valores máximos del 43%, con un promedio cercano al 20%. Tanto la producción de hidrógeno como la remoción de DQO presentaron una dependencia inversamente proporcional al TRH. Los resultados obtenidos en este estudio demuestran que la fermentación anaerobia en un reactor UASB abre la posibilidad de utilizar las vinazas para producir hidrógeno molecular de forma sostenible.

The 4th surveillance test and evaluation of the reactor pressure vessel material (capsule W) of Younggwang nuclear power plant unit1

Energy Technology Data Exchange (ETDEWEB)

Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwon Jae [Korea Atomic Energy Research Institute, Taejeon (Korea)

2001-08-01

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 4th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Yonggwang site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Yonggwang unit 1 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X and W are 5.555E+18, 1.662E+19, 3.358E+19, and 4.521E+19 n/cm{sup 2}, respectively. The bias factor, the ratio of measurement versus calculation, was 0.859 for the 1st through 4th testing and the calculational uncertainty, 11.80% satisfied the requirement of USNRC Reg.Guide 1.190, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.551E+19 n/cm{sup 2} based on the end of 12th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 3.929E+19, 4.880E+19, 5.831E+19 and 6.782E+19 n/cm{sup 2} based on the current calculation. The result through this analysis for Yonggwang unit 1 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 4 refs., 41 figs., 35 tabs. (Author)

The 4th surveillance test and evaluation of the reactor pressure vessel material (capsule W) of Yonggwang nuclear power plant unit 2

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwon Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

2001-02-01

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 4th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Yonggwang unit 2 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X and W are 5.762E+18, 1.5391E+19, 3.5119E+19, and 4.2610E+19 n/cm{sup 2}, respectively. The bias factor, the ratio of measurement versus calculation, was 0.899 for the 1st through 4th testing and the calculational uncertainty, 12.3% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.357E+19 n/cm{sup 2} based on the end of 11th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 3.525E+19, 4.337E+19, 5.148E+19 and 5.960E+19 n/cm{sup 2} based on the current calculation. The result through this analysis for Yonggwang unit 2 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 48 refs., 35 figs., 42 tabs. (Author)

Papers presented as part of the status report of the Nuclear Safety Research Project of the Karlsruhe Nuclear Center on 23 March 1994

International Nuclear Information System (INIS)

Hueper, R.

1994-05-01

The ten papers deal with the state of safety requirements on future LWR plants and with nuclear safety research with regard to fast reactors and future PWR plants. In particular, passive after-heat removal, core disruptive accidents, and actinide burning in fast reactors are analysed. For PWR type plants the fuel element behaviour in the event of accidents, hydrogen distribution and hydrogen fires, and the origin and effects of steam explosions on the reactor pressure vessel and the containment are examined. Core meltdown cooling systems are suggested. (DG) [de

Actualización del sistema SCADA y de control para los reactores MQ5 y MQ6 de la planta de Pinturas Condor, Sherwin Williams Ecuador

Directory of Open Access Journals (Sweden)

Jonathan Reinoso

2013-12-01

Full Text Available El presente documento describe la actualización del sistema SCADA para los reactores MQ5 y MQ6 de la planta de Pinturas Condor mediante el software Intouch y la actualización del sistema de control del reactor MQ5 implementado en un controlador lógico programable (PLC de marca SCHNEIDER, además de la arquitectura de control realizada en el proyecto. El sistema SCADA y de control de los reactores permiten la visualización y control de los datos y variables más relevantes durante las diferentes fases de producción de resinas en los reactores MQ5 y MQ6.

Final report for the 5th surveillance test of the reactor pressure vessel material (capsule Y) of Yonggwang Nuclear Power Plant unit 2

Energy Technology Data Exchange (ETDEWEB)

Lee, Sam Lai; Kim, ByoungChul; Chang, Kee Ok (and others)

2006-02-15

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 5th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Daejeon after the capsule was transported from Yonggwang site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Yonggwang unit 2 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X, W and Y are 5.777E+18, 1.5371E+19, 3.7634E+19, 4.3045E+19, and 4.8662E+19n/cm{sup 2}, respectively. The bias factor, the ratio of calculation/measurement, was 0.953 for the 1st through 5th testing and the calculational uncertainty,7.2% satisfied the requirement of USNRC Reg.Guide 1.190, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.659E+19n/cm{sup 2} based on the end of 13th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 48, 56 and 64EFPY would reach 3.625E+19, 5.293E+19, 6.127E+19 and 6.960E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Yonggwang unit 2 showed that there would be no problem for the Pressurized Thermal Shock(PTS) during the operation until design life.

Efecto de la concentración de SO2 en las reacciones de calcinación y sulfatación de calcáreos en reactores de lecho fluidizado. // Effect of the SO2 concentration in the calcinations and sulfatation reactions in a fluidized bed reactor.

Directory of Open Access Journals (Sweden)

J. E. Lindo Samaniego

2008-01-01

Full Text Available Fue realizado un estudio sobre el efecto de las concentraciones de SO2 en la absorción por calcáreo en hornos de LechoFluidizado. Para observar la influencia del SO2 en los parámetros de diferentes procesos físicos y químicos fueron creadosambientes para cuatro concentraciones diferentes de SO2 : 500, 1000, 2000 y 4000 ppm. Se utilizaron dos tipos decalcáreos: Dolimitico-DP y el Calcítico-CI. El Lecho Fluidizado Burbujeante utilizado tiene 160 mm de diámetro interno yfue fluidizado con aire a la temperatura de 850 °C, con una concentración de SO2 deseada. Como material del lecho fueutilizada la arena de cuarzo (99,9% con diámetro de 385 μm y de masa aproximadamente 3,0 kg. El calcáreo fueadicionado en dosificación de 50 g con el reactor ya pre-calentado. Las variaciones de las concentraciones de SO2, CO2,CO, O2 y las descargas, fueron monitoreadas continuamente a la salida del ciclón que fue utilizado para la retención de lapartícula fina. Para esos dados se desarrolló un programa en LabView. El modelo matemático escogido posibilitó ladeterminación de la conversión.Palabras claves: Lecho fluidizado, dióxido de azufre, absorción de azufre, calcáreo , reactor de lechofluidizado.___________________________________________________________________________Abstract.A Study of the effect of the concentrations of SO2 in its absorption by limestones in fluidized bed furnaces wasconducted. For the determination of the SO2 influence on the different physical and chemical parameters of process,such as calcinations and sulfatation four different atmospheres were used in the reator with concentrations of SO2 of500, 1000, 2000 and 4000 ppm. Two types of limestones were used: Dolomite-DP and Calcitic-CI. The bench scalebubbling fluidized bed reactor had a 160 mm internal diameter and was fluidized with air at 850 °C containing therequired concentration of SO2. Bed material was quartz sand (99,9% , with 385 μm diameter and approximately

Modelo estadístico para la simulación de reactores de lixiviación ácida

Directory of Open Access Journals (Sweden)

Mónica Hernández-Rodríguez

2015-05-01

Full Text Available Se desarrolló un modelo estadístico que permite simular el comportamiento de la batería de reactores en el proceso de lixiviación ácida y determinar a partir de parámetros operacionales la eficiencia de extracción de níquel y de cobalto. Al realizar las pruebas de validación se obtuvo que más del 95% de los valores determinados por el modelo están dentro de los límites de confianza estimados, sin embargo se observa una tendencia a que el valor calculado se encuentre por debajo del reportado, lo cual se cumple para el 65,79 % y el 61,84 %, de los datos, con relación a la eficiencia de extracción de níquel y cobalto, respectivamente. Se realizó un análisis de sensibilidad paramétrica para establecer la influencia de las variables de operación en el sistema. Se concluye que la sensibilidad depende del nivel de operación del sistema y que las variables más significativas en todos los niveles son: la concentración de magnesio y la de níquel así como la relación ácido - mineral

Analysis of influence of fast neutron fluence irradiated to Beryllium element of The RSG-GAS reactor

International Nuclear Information System (INIS)

Sri Kuntjoro

2010-01-01

Analysis of influence fast neutron fluence irradiated to the RSG-GAS beryllium reflector have been done. Methods of analysis was carried out by measuring fluxes neutron in beryllium element and block position that function as reflector.The calculation done for determination it is there any influence of neutron as long as beryllium in the core. Besides that, visualization done to make sure it there is any deformation at beryllium as effect of irradiation. Fluxes and fluences of beryllium element measurement result in 200 kW reactor power are 2.30E+07 n/cm 2 .sec and 4.19E+17 n/cm 2 in position E-2, 3.70E+07 n/cm 2 s and 6.74E+17 n/cm 2 in position J-8, 2.19E+12 n/cm 2 s and 3.99E+22 n/cm 2 in position. Measurement results in the position B-3 are 2.12E+12 n/cm 2 s and 3.86E+22 n/cm 2 in position G-10 respectively. Other result are fluxes and fluence in beryllium block, those are 5,02E+07 n/cm 2 s and 9,15E+17 n/cm 2 in position (5-6), and 2,32E+07 n/cm 2 s and 4,23E+17 n/cm 2 in position (C-D). Deformation (L/L) results for beryllium element are 1,12E-08 in position E-2, 1,84E-08 in position J-8, 1,60E-03 in position B-3, and 1,55E-03 in position G-10. In beryllium block deformation results are 2,52E-08 in position (5-6) and 1,13E-08 in position (C-D). Those results are shown unseen deformation in beryllium element and beryllium block and demonstrably by visual observation in reactor hot cell. (author)

Reactor water spontaneous circulation structure in reactor pressure vessel

International Nuclear Information System (INIS)

Takahashi, Kazumi

1998-01-01

The gap between the inner wall of a reactor pressure vessel of a BWR type reactor and a reactor core shroud forms a down comer in which reactor water flows downwardly. A feedwater jacket to which feedwater at low temperature is supplied is disposed at the outer circumference of the pressure vessel just below a gas/water separator. The reactor water at the outer circumferential portion just below the air/water separator is cooled by the feedwater jacket, and the feedwater after cooling is supplied to the feedwater entrance disposed below the feedwater jacket by way of a feedwater introduction line to supply the feedwater to the lower portion of the down comer. This can cool the reactor water in the down comer to increase the reactor water density in the down comer thereby forming strong downward flows and promote the recycling of the reactor water as a whole. With such procedures, the reactor water can be recycled stably only by the difference of the specific gravity of the reactor water without using an internal pump. In addition, the increase of the height of the pressure vessel can be suppressed. (I.N.)

Nuclear reactor, reactor core thereof, and device for constituting the reactor

International Nuclear Information System (INIS)

Takiyama, Masashi.

1994-01-01

A reactor core is constituted by charging coolants (light water) in a reactor pressure vessel and distributing fuel assemblies, reflecting material sealing pipes, moderator (heavy water and helium gas) sealing pipes, and gas sealing pipes therein. A fuel guide tube is surrounded by a cap and the gap therebetween is made hollow and filled with coolant steams. The cap is supported by a baffle plate. The moderator sealing pipe is disposed in a flow channel of coolants in adjacent with the cap. The position of the moderator sealing tube in the reactor core is controlled by water stream from a hydraulic pump with a guide tube extending below the baffle plate being as a guide. Then, the position of the moderator sealing tube is varied to conduct power control, burnup degree compensation, and reactor shut down. With such procedures, moderator cooling facility is no more necessary to simplify the structure. Further, heat generated from the moderator is transferred to the coolants thereby improving heat efficiency of the reactor. (I.N.)

Estudio de la recuperación de cromo hexavalente mediante un reactor electroquímico de compartimentos separados por separadores cerámicos

OpenAIRE

REYES PINEDA, HENRY

2011-01-01

La Tesis Doctoral "Estudio de la recuperación de cromo hexavalente mediante un reactor electroquímico de compartimentos separados por separadores cerámicos" se centra en la posibilidad de recuperación del cromo hexavalente procedente de las disoluciones de mordentado de las industrias de metalizado de plásticos mediante la utilización de un reactor electroquímico de compartimentos separados por separadores cerámicos fabricados a diferente presión y diferente composición de almidón. Con la rec...

EVOLUCIÓN DEL COMPORTAMIENTO VISCOELÁSTICO DEL ASFALTO INDUCIDA BAJO TERMO-OXIDACIÓN IN SITU EN UN REO-REACTOR

Directory of Open Access Journals (Sweden)

XIOMARA VARGAS

2008-01-01

Full Text Available En este artículo se presentan los resultados del proceso de termo-oxidación de asfalto realizados por primera vez en un reo-reactor. El comportamiento viscoelástico del asfalto pudo ser representado por una ley de potencia (G'(w - wn, G'' (w - w1. La variación del exponente 'n' reflejó los cambios estructurales del asfalto inducidos por el proceso de termo-oxidación. En el intervalo de frecuencia experimental y a 200 y 250°C, los módulos elástico G' y viscoso G'' mostraron una relación del tipo: G'' (w - wn y G' (w ~ wn, este comportamiento es equivalente a un 'gel-débil' y confirma los cambios estructurales del asfalto inducidos por el envejecimiento termo-oxidativo.

Standard Guide for Application of Neutron Transport Methods for Reactor Vessel Surveillance, E706 (IID)

CERN Document Server

American Society for Testing and Materials. Philadelphia

2011-01-01

1.1 Need for Neutronics Calculations—An accurate calculation of the neutron fluence and fluence rate at several locations is essential for the analysis of integral dosimetry measurements and for predicting irradiation damage exposure parameter values in the pressure vessel. Exposure parameter values may be obtained directly from calculations or indirectly from calculations that are adjusted with dosimetry measurements; Guide E944 and Practice E853 define appropriate computational procedures. 1.2 Methodology—Neutronics calculations for application to reactor vessel surveillance encompass three essential areas: (1) validation of methods by comparison of calculations with dosimetry measurements in a benchmark experiment, (2) determination of the neutron source distribution in the reactor core, and (3) calculation of neutron fluence rate at the surveillance position and in the pressure vessel. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is th...

Evaluación del comportamiento hidrodinámico como herramienta para optimización de reactores anaerobios de crecimiento en medio fijo

OpenAIRE

Andrea Pérez; Patricia Torres

2008-01-01

Las condiciones de flujo no ideal en los reactores afectan su desempeño; las causas comunes son cortos circuitos, zonas muertas y recirculación interna por corrientes cinéticas y/o de densidad. En este estudio se optimizó el diseño de un filtro anaerobio a escala real que trata las aguas residuales del proceso de extracción de almidón de yuca, el cual presentaba problemas de represamiento y bajas eficiencias de remoción. La evaluación del comportamiento hidrodinámico inicial mostró la presenc...

INTERPRETACIÓN E INTEGRACIÓN NORMATIVA

Directory of Open Access Journals (Sweden)

Eleonora del Pilar Salazar Londoño

2012-01-01

Full Text Available El objetivo del presente artículo es reflexionar sobre el fenómeno de la interpretación en la norma jurídica. Por esta razón, se construye un diálogo con diversos horizontes teóricos que se sitúan entre los teóricos del derecho de un pensamiento iuspositivista e iusnaturalista, dentro de teorías constructivistas, como Dworkin y Hart, teoría argumentativa como Alexy y Habermas, positivistas puros como Kelsen, entre otros. Todos alimentan el discurso hermenéutico con nuevos conceptos de interpretación, como nuevas tendencias de interpretaciones jurídicas. El diálogo entre los teóricos se direcciona a través de preguntas para resolver el problema de la interpretación en el tema de los principios y la integración normativa.

Environmental impacts of an accident with a nuclear power plant

International Nuclear Information System (INIS)

1985-10-01

A maximum credible reactor accident is considered: all safety systems fail and the reactor core is not cooled anymore. This so-called meltdown accident is discussed for two different weather situations. For these cases, the effects on public health and environment is studied (radioactive clouds, inhalation and deposition of radioactive materials). The radiation doses calculated are compared with standard levels. In so doing, an estimation is made of the measures necessary to reduce unfavourable consequences. (G.J.P.)

Benthic megafauna at deep-sea study areas W-N and E-N

International Nuclear Information System (INIS)

Keller, C.H.

1985-01-01

Photographs were utilized determine what megafaunal organisms live at areas E-N and W-N and in what densities. Life history characteristics gleaned from the literature as well as from the photographs are presented to establish these organisms' roles in oceanic food chains. In area W-N, the most abundant megafaunal group is the echinoderms. These are the asteroids, crinoids, echinoids, holothuroids, and ophiuroids. Dominant amongst the echinoderms are the ophiuroids, which account for about 46% of the total density. Taxonomic and photographic resolution at area E-N are both poor. Numbers of megafaunal organisms cannot be directly compared between areas E-N and W-N. Differing photographic techniques severely limit comparisons between the two areas. Nevertheless, megafauna seen at area E-N is apparently less dense and probably less diverse than at area W-N. 30 references, 8 figures, 8 tables

Determination of n, γ radiation field around the building of the swimming-pool reactor

International Nuclear Information System (INIS)

Jiang Jinling; Wen Youqin; Chen Changmao

1986-01-01

This work has measured the dose distribution of n, gamma radiation field around the building of the swimming-pool reactor by use of the highly sensitive neutron Rem counter and PTB-H 7907 exposure ratemeter. The measured datum show that the maximum value of n, gamma dose are 3-4 times greater than the background on certain distance from the building. Generally, the neutron doses are 2-3 times larger than gamma doses on most points

Dispositivo de posicionamiento de muestras biológicas para su irradiación en un canal radial de un reactor nuclear // Biological samples positioning device for irradiations on a radial channel at the nuclear research reactor

Directory of Open Access Journals (Sweden)

Maritza Rodríguez - Gual

2010-05-01

Full Text Available ResumenPor la demanda de un dispositivo experimental para el posicionamiento de las muestras biológicaspara su irradiación en un canal radial de un reactor nuclear de investigaciones en funcionamiento, seconstruyó y se puso en marcha un dispositivo para la colocación y retirada de las muestras en laposición de irradiación de dicho canal. Se efectuaron las valoraciones económicas comparando conotro tipo de dispositivo con las mismas funciones. Este trabajo formó parte de un proyectointernacional entre Cuba y Brasil que abarcó el estudio de los daños inducidos por diferentes tipos deradiación ionizante en moléculas de ADN. La solución propuesta es comprobada experimentalmente,lo que demuestra la validez práctica del dispositivo. Como resultado del trabajo, el dispositivoexperimental para la irradiación de las muestras biológicas se encuentra instalado y funcionando yapor 5 años en el canal radial # 3(BH#3 Palabras claves: reactor nuclear de investigaciones, dispositivo para posicionamiento de muestras,___________________________________________________________________________AbstractFor the demand of an experimental device for biological samples positioning system for irradiationson a radial channel at the nuclear research reactor in operation was constructed and started up adevice for the place and remove of the biological samples from the irradiation channels withoutinterrupting the operation of the reactor. The economical valuations are effected comparing withanother type of device with the same functions. This work formed part of an international projectbetween Cuba and Brazil that undertook the study of the induced damages by various types ofionizing radiation in DNA molecules. Was experimentally tested the proposed solution, whichdemonstrates the practical validity of the device. As a result of the work, the experimental device forbiological samples irradiations are installed and operating in the radial beam hole #3(BH#3

Nuclear reactor

International Nuclear Information System (INIS)

Garabedian, G.

1988-01-01

A liquid reactor is described comprising: (a) a reactor vessel having a core; (b) one or more satellite tanks; (c) pump means in the satellite tank; (d) heat exchanger means in the satellite tank; (e) an upper liquid metal conduit extending between the reactor vessel and the satellite tank; (f) a lower liquid metal duct extending between the reactor vessel and satellite tanks the upper liquid metal conduit and the lower liquid metal duct being arranged to permit free circulation of liquid metal between the reactor vessel core and the satellite tank by convective flow of liquid metal; (g) a separate sealed common containment vessel around the reactor vessel, conduits and satellite tanks; (h) the satellite tank having space for a volume of liquid metal that is sufficient to dampen temperature transients resulting from abnormal operating conditions

Nuclear reactor construction with bottom supported reactor vessel

International Nuclear Information System (INIS)

Sharbaugh, J.E.

1987-01-01

This patent describes an improved liquid metal nuclear reactor construction comprising: (a) a nuclear reactor core having a bottom platform support structure; (b) a reactor vessel for holding a large pool of low pressure liquid metal coolant and housing the core; (c) a containment structure surrounding the reactor vessel and having a sidewall spaced outwardly from the reactor vessel side wall and having a base mat spaced below the reactor vessel bottom end wall; (d) a central small diameter post anchored to the containment structure base mat and extending upwardly to the reactor vessel to axially fix the bottom end wall of the reactor vessel and provide a center column support for the lower end of the reactor core; (e) annular support structure disposed in the reactor vessel on the bottom end wall and extending about the lower end of the core; (f) structural support means disposed between the containment structure base mat and bottom end of the reactor vessel wall and cooperating for supporting the reactor vessel at its bottom end wall on the containment structure base mat to allow the reactor vessel to expand radially but substantially prevent any lateral motions that might be imposed by the occurrence of a seismic event; (g) a bed of insulating material disposed between the containment structure base mat and the bottom end wall of the reactor vessel and uniformly supporting the reactor vessel at its bottom end wall; freely expand radially from the central post as it heats up while providing continuous support thereof; (h) a deck supported upon the wall of the containment vessel above the top open end of the reactor vessel; and (i) extendible and retractable coupling means extending between the deck and the top open end of the reactor vessel and flexibly and sealably interconnecting the reactor vessel at its top end to the deck

Optimization of fusion power density in the two-energy-component tokamak reactor

International Nuclear Information System (INIS)

Jassby, D.L.

1974-10-01

The optimal plasma conditions for maximizing fusion power density P/sub f/ in a beam-driven D--T tokamak reactor (TCT) are considered. Given T/sub e/ = T/sub i/ and fixed total plasma pressure, there is an optimal n/sub e/tau/sub E/ for maximizing P/sub f/, viz. n/sub e/tau/sub E/ = 4 x 10 12 to 2 x 10 13 cm -3 sec for T/sub e/ = 3--15 keV and 200-keV D beams. The corresponding anti GAMMA equals (beam pressure/bulk-plasma pressure) is 0.96 to 0.70. P/sub fmax/ increases as T/sub e/ is reduced and can be an order of magnitude larger than the maximum P/sub f/ of a thermal reactor of the same beta, at any temperature. A lower practical limit to T/sub e/ may be set by requiring a minimum beam power multiplication Q/sub b/. For the purpose of fissile breeding, the minimum Q/sub b/ approximately 0.6, requiring T/sub e/ greater than or equal to 3 keV if Z = 1. The optimal operating conditions of a TCT for obtaining P/sub fmax/ are considerably different from those for enhancing Q/sub b/. Maximizing P/sub f/ requires restricting both T/sub e/ and n/sub e/tau/sub E/, maintaining a bulk plasma markedly enriched in tritium, and spoiling confinement of fusion alphas. Considerable impurity content can be tolerated without seriously degrading P/sub fmax/, and high-Z impurity radiation may be useful for regulating tau/sub E/. (auth)

RESOLUCIÓN DE UN PROBLEMA INVERSO VÍA SUBESTIMACIÓN LINEAL A TROZOS //\tAN INVERSE PROBLEM RESOLUTION VIA PIECEWISE LINEAR UNDERESTIMATION

Directory of Open Access Journals (Sweden)

Javier Hernádez Benítez

2012-12-01

Full Text Available In reactor design phase bubble column type (CBT is required to have the distribution of solids within the reactor. This distribution satisfies an ordinary differential equation (ODE of order two, with boundary conditions that was developed by D. R. Cova [2], followed by D. N. Smith and J. A. Ruether [8]. Some elements of this equation are given by correlations that depend on certain parameters that are unknown but may be obtained from experimental data. The methodology used to determine these parameters is the sub- piecewise linear underestimation developed by O. L. Mangasarian, J. B. Rosen, M. E. Thompson. // RESUMEN: En el diseño de reactores trifásicos tipo columna de burbujeo (CBT, se requiere tener la distribución de solidos dentro del reactor. Esta distribución satisface una ecuación diferencial ordinaria (EDO de orden dos, con condiciones de frontera que fue desarrollada por D. R. Cova [2], y posteriormente por D. N. Smith y J. A. Ruether [8]. Algunos elementos de esta ecuación están dados por correlaciones que dependen de ciertos parámetros que son desconocidos, pero se pueden obtener a partir de datos experimentales. La metodología utilizada para determinar dichos parámetros es la sub-estimación lineal a trozos desarrollada por O. L. Mangasarian, J. B. Rosen y M. E. Thompson.

Measuring Public Acceptance of Nuclear Technology with Big data

Energy Technology Data Exchange (ETDEWEB)

Roh, Seugkook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

Surveys can be conducted only on people in specific region and time interval, and it may be misleading to generalize the results to represent the attitude of the public. For example, opinions of a person living in metropolitan area, far from the dangers of nuclear reactors and enjoying cheap electricity produced by the reactors, and a person living in proximity of nuclear power plants, subject to tremendous damage should nuclear meltdown occur, certainly differs for the topic of nuclear generation. To conclude, big data is a useful tool to measure the public acceptance of nuclear technology efficiently (i.e., saves cost, time, and effort of measurement and analysis) and this research was able to provide a case for using big data to analyze public acceptance of nuclear technology. Finally, the analysis identified opinion leaders, which allows target-marketing when policy is executed.

Measuring Public Acceptance of Nuclear Technology with Big data

International Nuclear Information System (INIS)

Roh, Seugkook

2015-01-01

Surveys can be conducted only on people in specific region and time interval, and it may be misleading to generalize the results to represent the attitude of the public. For example, opinions of a person living in metropolitan area, far from the dangers of nuclear reactors and enjoying cheap electricity produced by the reactors, and a person living in proximity of nuclear power plants, subject to tremendous damage should nuclear meltdown occur, certainly differs for the topic of nuclear generation. To conclude, big data is a useful tool to measure the public acceptance of nuclear technology efficiently (i.e., saves cost, time, and effort of measurement and analysis) and this research was able to provide a case for using big data to analyze public acceptance of nuclear technology. Finally, the analysis identified opinion leaders, which allows target-marketing when policy is executed

Elements on reactor control

International Nuclear Information System (INIS)

Bruna, G.B.

1998-01-01

In order to achieve the two-fold goal of maximizing the energy obtained from reactor fuel and ensuring the large flexibility of plant operation in respect to safety regulations and keeping the reactor integrity the control of PWRs is generally based on real time monitoring and analysing of independent neutronic parameters: thermal power release, axial power distribution in the core and temperatures of the primary loop. Two control chains more or less coupled according to the control chosen mode are in charge of the control of these parameters. With the brief history of control in French power reactors the advanced X control mode adopted by Framatome for N4 plants is described in detail. A summary of N4 reactor control and protection system is included

Nuclear reactor monitoring device

International Nuclear Information System (INIS)

Mihashi, Ishi; Honma, Hitoshi.

1993-01-01

The monitoring device of the present invention comprises a reactor core/reactor system data measuring and controlling device, a radioactivity concentration calculation device for activated coolants for calculating a radioactivity concentration of activated coolants in a main steam and reactor water by using an appropriate physical model, a radioactivity concentration correlation and comparison device for activated coolants for comparing correlationship with a radiation dose and an abnormality alarm device. Since radioactivity of activated primary coolants is monitored at each of positions in the reactor system and occurrence of leakage and the amount thereof from a primary circuit to a secondary circuit is monitored if the reactor has secondary circuit, integrity of the reactor system can be ensured and an abnormality can be detected rapidly. Further, radioactivity concentration of activated primary circuit coolants, represented by 16 N or 15 C, is always monitored at each of positions of PWR primary circuits. When a heat transfer pipe is ruptured in a steam generator, leakage of primary circuit coolants is detected rapidly, as well as the amount of the leakage can be informed. (N.H.)

Generation of net electric power with a tokamak reactor under foreseeable physical and engineering conditions

International Nuclear Information System (INIS)

Hiwatari, R.; Asaoka, Y.; Okano, K.; Yoshida, T.; Tomabechi, K.

2004-01-01

This study reveals for the first time the plasma performance required for a tokamak reactor to generate net electric power under foreseeable engineering conditions. It was found that the reference plasma performance of the ITER inductive operation mode with β N = 1.8, HH = 1.0, andf nGW 0.85 had sufficient potential to achieve the electric break-even condition (net electric power P e net = 0MW) under the following engineering conditions: machine major radius 6.5m ≤ R p ≤ 8.5m, the maximum magnetic field on TF coils B tmax = 16 T, thermal efficiency η e 30%, and NBI system efficiency η NBI = 50%. The key parameters used in demonstrating net electric power generation in tokamak reactors are β N and fη GW . ≥ 3.0 is required for P e net ∼ 600MW with fusion power P f ∼ 3000MW. On the other hand, fη GW ≥ 1.0 is inevitable to demonstrate net electric power generation, if high temperatures, such as average temperatures of T ave > 16 keV, cannot be selected for the reactor design. To apply these results to the design of a tokamak reactor for demonstrating net electric power generation, the plasma performance diagrams on the Q vs P f (energy multiplication factor vs fusion power) space for several major radii (i.e. 6.5, 7.5, and 8.5 m) were depicted. From these figures, we see that a design with a major radius R p ∼ 7.5m seems preferable for demonstrating net electric power generation when one aims at early realization of fusion energy. (author)

EVALUACIÓN DE LA SENSIBILIDAD PARAMÉTRICA DEL PROCESO DE SÍNTESIS DE LA CICLONITA EN UN REACTOR POR LOTES

Directory of Open Access Journals (Sweden)

Juan Carlos Ojeda Toro

Full Text Available En este trabajo se evaluó la sensibilidad paramétrica del proceso de síntesis de la ciclonita en un reactor por lotes. Esto con el fin de definir condiciones seguras de operación para esta reacción altamente exotérmica. La ley de velocidad de la reacción se ajustó a partir de datos experimentales disponibles en la literatura. Reparametrizando los balances de materia y energía del reactor, se estableció la sensibilidad de la temperatura de reacción con respecto a la variación de la temperatura inicial del sistema reactivo y la temperatura del medio refrigerante. Para determinar las condiciones críticas de operación del reactor, se usó como criterio el cálculo de los coeficientes de sensibilidad y los perfiles de temperatura-conversión así como el lugar geométrico de los máximos de estas curvas. Se definió para el sistema reactivo un potencial crítico de generación de calor (M igual a 34 y que las condiciones críticas de Runaway corresponden a un número de Semenov (ψ igual a 0,684, un parámetro de calor de reacción (B igual a 15 y un número del tipo Arrhenius (γ con un valor de 20. Así mismo, los perfiles de temperatura-conversión precisan una relación crítica entre el potencial de enfriamiento y generación de calor de 2,5786 (N/M.

Problems of creating fuel elements for fast gas-cooled reactors working on N2O4-dissociating coolant

International Nuclear Information System (INIS)

Nesterenko, V.B.; Zelensky, V.F.; Kolykhan, L.I.; Karpenko, G.V.; Krasnorutsky, V.S.; Isakov, V.P.; Ashikhmin, V.P.; Permyakov, L.N.

1985-01-01

A variant of fast gas-cooled reactors is one using dissociating N 2 O 4 nitrogen tetroxide as a coolant. This type of reactors is promising because of great thermal effects of dissociation reactions while heating and recombination while cooling; small latent heat of evaporation; high heat transfer coefficient owing to additional heat transfer in a chemical reaction; high N 2 O 4 density in a gas state at operation parameters. The mentioned advantages give possibility to create a small turbine, heat exchange apparatus and to get high heat production in the active zone. All this opens new ways to increase power plants effectiveness

Research reactors

International Nuclear Information System (INIS)

Merchie, Francois

2015-10-01

This article proposes an overview of research reactors, i.e. nuclear reactors of less than 100 MW. Generally, these reactors are used as neutron generators for basic research in matter sciences and for technological research as a support to power reactors. The author proposes an overview of the general design of research reactors in terms of core size, of number of fissions, of neutron flow, of neutron space distribution. He outlines that this design is a compromise between a compact enough core, a sufficient experiment volume, and high enough power densities without affecting neutron performance or its experimental use. The author evokes the safety framework (same regulations as for power reactors, more constraining measures after Fukushima, international bodies). He presents the main characteristics and operation of the two families which represent almost all research reactors; firstly, heavy water reactors (photos, drawings and figures illustrate different examples); and secondly light water moderated and cooled reactors with a distinction between open core pool reactors like Melusine and Triton, pool reactors with containment, experimental fast breeder reactors (Rapsodie, the Russian BOR 60, the Chinese CEFR). The author describes the main uses of research reactors: basic research, applied and technological research, safety tests, production of radio-isotopes for medicine and industry, analysis of elements present under the form of traces at very low concentrations, non destructive testing, doping of silicon mono-crystalline ingots. The author then discusses the relationship between research reactors and non proliferation, and finally evokes perspectives (decrease of the number of research reactors in the world, the Jules Horowitz project)

Measurement and Calculation of Gamma Radiation from HWZPR Reactor

International Nuclear Information System (INIS)

Jalali, Majid

2006-01-01

HWZPR is a research reactor with natural uranium fuel, D 2 O moderator and graphite reflector with maximum power of 100 W. It is a suitable means for theoretical research and heavy water reactor experiments. Neutrons from the core participate in different nuclear reactions by interactions with fuel, moderator, graphite and the concrete around the reactor. The results of these interactions are the production of prompt gammas in the environment. Useful information is gained by the reactor gamma spectrum measurement from point of view of relative quantity and energy distribution of direct and scattered radiations. Reactor gamma ray spectrum has been gathered in different places around the reactor by HPGe detector. In analysis of these spectra, 1 H(n,γ) 2 H, 16 O(n,n'γ) 16 O, 2 H(n,γ) 3 H and 238 U(n,γ) 239 U reactions occurring in reactor moderator and fuel, are important. The measured spectrum has been primarily estimated by the MCNP code. There is agreement between the code and the experiments in some points. The scattered gamma rays from 27 Al (n,γ) 28 Al reaction in the reactor tank, are the most among the gammas scattered in the reactor environment. Also the dose calculations by MCNP code show that 72% of gamma dose belongs to the energy range 3-11 MeV from reactor gamma spectrum and the danger of exposure from the reactor high-energy photons is serious. (author)

Recriticality, a Key Phenomenon to Investigate in Core Disruptive Accident Scenarios of Current and Future Fast Reactor Designs

International Nuclear Information System (INIS)

Maschek, W.; Rineiski, A.; Flad, M.; Kriventsev, V.; Gabrielli, F.; Morita, K.

2012-01-01

Final comments and conclusions: • Modern plants, should have performed better under Fukushima type event. • In future fast reactor systems significantly higher active and passive safety features are installed, which should cope with events like Fukushima. • One important lesson: put a focus on rare initiators, accident routes and consequences that are neither expected nor have been observed, events that are categorized under ‘black swans’. • Importance of severe accident research demonstrated - both analytically and experimentally for assessing and interpreting accident scenarios and developments. Precondition for developing preventive & mitigative safety measures. Passive safety measures are in the focus of advanced design options and must work under conditions of multiple loads and aggravating events. • Fast reactor systems behavior as the SFR under severe accident conditions: – In fast spectrum systems as the SFR the core is not in its neutronically most reactive configuration and SFRs may be loaded with MAs for waste management; – Recriticalities have a high probability because of the higher enrichment levels; – Short time scales have to be envisioned for core melt-down; – Decay heat levels might be significantly higher, if MA bearing fuel is involved. • Improve design by measures for prevention and/or mitigation of recriticalities; – High reliability of simulations required for proof; • Assessment of fuel relocated on peripheral structures; • Preventive/mitigating measures should not replace containment measures

Sensitivity Analysis of Core Damage from Reactor Coolant Pump Seal Leakage during Extended Loss of All AC Power

Energy Technology Data Exchange (ETDEWEB)

Park, Da Hee; Kim, Min Gi; Lee, Kyung Jin; Hwang, Su hyun; Lee, Byung Chul [FNC Technology Co. Ltd., Yongin (Korea, Republic of); Yoon, Duk Joo; Lee, Seung Chan [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2015-10-15

In this study, in order to comprehend the Fukushima accident, the sensitivity analysis was performed to analyze the behavior of Reactor Coolant System (RCS) during ELAP using the RELAP5/MOD3.3 code. The Fukushima accident was caused by tsunami resulted in Station Black Out (SBO) followed by the reactor core melt-down and release of radioactive materials. After the accident, the equipment and strategies for the Extended Loss of All AC Power (ELAP) were recommended strongly. In this analysis, sensitivity studies for the RCP seal failure of the OPR1000 type NPP were performed by using RELAP5/MOD3.3 code. Six cases with different leakage rate of RCP seal were studied for ELAP with operator action or not. The main findings are summarized as follows: (1) Without the operator action, the core uncovery time is determined by the leakage rate of RCP seal. When the leakage rate per RCP seal are 5 gpm, 50 gpm, and 300 gpm respectively, the core uncovery time are 1.62 hr, 1.58 hr, and 1.29 hr respectively. Namely, If the leakage rate of RCP seal was much bigger, the uncover time of core would be shorter. (2) In case that the cooling by SG secondary side was performed using the TDAFP and SG ADV, the core uncovery time was significantly extended.

FBR type reactor

International Nuclear Information System (INIS)

Kimura, Kimitaka; Fukuie, Ken; Iijima, Tooru; Shimpo, Masakazu.

1994-01-01

In an FBR type reactor for exchanging fuels by pulling up reactor core upper mechanisms, a connection mechanism is disposed for connecting the top of the reactor core and the lower end of the reactor core upper mechanisms. In addition, a cylindrical body is disposed surrounding the reactor core upper mechanisms, and a support member is disposed to the cylindrical body for supporting an intermediate portion of the reactor core upper mechanisms. Then, the lower end of the reactor core upper mechanisms is connected to the top of the reactor core. Same displacements are caused to both of them upon occurrence of earthquakes and, as a result, it is possible to eliminate mutual horizontal displacement between a control rod guide hole of the reactor core upper mechanisms and a control rod insertion hole of the reactor core. In addition, since the intermediate portion of the reactor core upper mechanisms is supported by the support member disposed to the cylindrical body surrounding the reactor core upper mechanisms, deformation caused to the lower end of the reactor core upper mechanisms is reduced, so that the mutual horizontal displacement with respect to the control rod insertion hole of the reactor core can be reduced. As a result, performance of control rod insertion upon occurrence of the earthquakes is improved, so that reactor shutdown is conducted more reliably to improve reactor safety. (N.H.)

Diseño de un reactor de transesterificación para la obtención de biodiesel a partir de aceites vegetales

OpenAIRE

MARSET GIMENO, DAVID

2016-01-01

[ES] En este proyecto se pretende que el alumno realice el diseño, montaje y puesta a punto un reactor de transesterificación de laboratorio para la obtención de biodiesel a partir de aceites vegetales, utilizando catálisis básica homogénea. Paralelamente se definirán las técnicas analíticas a emplear para el control de la calidad de los aceites de partida y el seguimiento de los productos de reacción. A partir de los resultados experimentales se realizará el diseño y estimación económica...

Survey of radiological contaminants in the near-shore environment at the Hanford Site 100-N Area reactor

International Nuclear Information System (INIS)

Van Verst, S.P.; Albin, C.L.; Patton, G.W.; Blanton, M.L.; Poston, T.M.; Cooper, A.T.; Antonio, E.J.

1998-09-01

Past operations at the Hanford Site 100-N Area reactor resulted in the release of radiological contaminants to the soil column, local groundwater, and ultimately to the near-shore environment of the Columbia River. In September 1997, the Washington State Department of Health (WDOH) and the Hanford Site Surface Environmental Surveillance Project (SESP) initiated a special study of the near-shore vicinity at the Hanford Site's retired 100-N Area reactor. Environmental samples were collected and analyzed for radiological contaminants ( 3 H, 90 Sr, and gamma/ emitters), with both the WDOH and SESP analyzing a portion of the samples. Samples of river water, sediment, riverbank springs, periphyton, milfoil, flying insects, clam shells, and reed canary grass were collected. External exposure rates were also measured for the near-shore environment in the vicinity of the 100-N Area. In addition, samples were collected at background locations above Vernita Bridge

Análisis de estabilidad del reactor PFTR para una reacción con cinética de primer orden utilizando la funcional de Lyapunov

Directory of Open Access Journals (Sweden)

Héctor Armando Durán Peralta

2007-01-01

Full Text Available Abunda la literatura referente al análisis de estabilidad de reactores con parámetros globalizados de concentración y temperatura (por ejemplo el CSTR, en cambio es escasa la literatura sobre la estabilidad de reactores con parámetros distribuidos donde existe distribución espacial de concentración y temperatura, como es el caso del reactor tubular PFTR. Este documento analiza la estabilidad del reactor PFTR isotérmico y no isotérmico para una reacción con cinética de primer orden utilizando la funcional de Lyapunov. Se trabaja con una cinética de primer orden pues un objetivo de este artículo es mostrar cómo se aplica la funcional de Lyapunov al análisis de un reactor de parámetros distribuidos, dado que es casi inexistente la literatura sobre el método de la funcional de Lyapunov aplicada a la estabilidad de reactores (técnica usada en el análisis de estabilidad de sistemas en ingeniería eléctrica. El análisis de estabilidad dio como resultado perfiles de temperatura y concentración asintóticamente estables para los casos PFTR isotérmico, no isotérmico con constante cinética independiente de la temperatura y PFTR no isotérmico adiabático. Para el PFTR con retiro de calor el análisis condujo a una región de estabilidad asintótica y a una región incierta donde puede o no haber oscilaciones.

Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This practice covers procedures for designing a surveillance program for monitoring the radiation-induced changes in the mechanical properties of ferritic materials in light-water moderated nuclear power reactor vessels. This practice includes the minimum requirements for the design of a surveillance program, selection of vessel material to be included, and the initial schedule for evaluation of materials. 1.2 This practice was developed for all light-water moderated nuclear power reactor vessels for which the predicted maximum fast neutron fluence (E > 1 MeV) at the end of license (EOL) exceeds 1 × 1021 neutrons/m2 (1 × 1017 n/cm2) at the inside surface of the reactor vessel. 1.3 This practice applies only to the planning and design of surveillance programs for reactor vessels designed and built after the effective date of this practice. Previous versions of Practice E185 apply to earlier reactor vessels. 1.4 This practice does not provide specific procedures for monitoring the radiation induced cha...

Study of the Δ structure and NΔ interactions with N(e,e'π) and d(e,e'π) reactions

International Nuclear Information System (INIS)

Lee, T.-S. H.

1998-01-01

A dynamical approach for using the γN -> πN and N(e,e primeπ) reactions to test the chiral constituent quark model is reviewed. Recent results for the Δ excitations and predictions for future experiments are presented. It is shown that the polarization observables of d(e,e primeπ) reactions are useful for investigating the NΔ interactions which are crucial in exploring the Δ components in nuclei and the properties of Δ-rich systems created in relativistic heavy-ion collisions

N E Zavoiskaya

Indian Academy of Sciences (India)

Logo of the Indian Academy of Sciences. Indian Academy of Sciences. Home · About IASc ... Resonance – Journal of Science Education. N E Zavoiskaya. Articles written in Resonance – Journal of Science Education. Volume 20 Issue 11 November 2015 pp 963-968 General Article. Zavoisky and the Discovery of EPR.

Research reactor DHRUVA

International Nuclear Information System (INIS)

Veeraraghaven, N.

1990-01-01

DHRUVA, a 100 MWt research reactor located at the Bhabha Atomic Research Centre, Bombay, attained first criticality during August, 1985. The reactor is fuelled with natural uranium and is cooled, moderated and reflected by heavy water. Maximum thermal neutron flux obtained in the reactor is 1.8 X 10 14 n/cm 2 /sec. Some of the salient design features of the reactor are discussed in this paper. Some important features of the reactor coolant system, regulation and protection systems and experimental facilities are presented. A short account of the engineered safety features is provided. Some of the problems that were faced during commissioning and the initial phase of power operation are also dealt upon

Evaluation of neutron flux in the WWR-SM reactor channel and in the irradiating zone of U-150 cyclotron

International Nuclear Information System (INIS)

Sadikov, I.I.; Zinov'ev, V.G.; Sadikova, Z.O.; Salimov, M.I.

2006-01-01

Full text: For effective work of a reactor, and correct planning of experiments related to the reactor irradiation of various materials it is required to control a neutron flux in the given irradiation point for a long irradiation period. For realization of research works on topazes ennobling under irradiation by reactor neutrons as well as by secondary neutrons produced in a cyclotron it is necessary to know the total neutron flux and spectra. To resolve the problem a technique for registration of neutrons with different energy and calculation of a neutrons spectrum in the given irradiation points in reactor channels and in cyclotron behind the nickel target has been developed. Neutron flux density and energy spectra were monitored by use of the following nuclear reactions: 59 Co(n,γ) 60 Co, 197 Au(n,γ) 198 Au, 58 Ni(n,p) 58 Co, 24 Mg(n,p) 24 Na, 48 Ti(n,p) 48 Sc, 46 Ti(n,p) 46 Sc, 54 Fe(n,p) 54 Mn, 89 Y(n,2n) 88 Y, 60 Ni(np) 60 Co. Gamma spectrometer composed of HPGe detector (Rel. Eff. - 15%) and Digital Spectra Analyzer DSA-1000 (Canberra Ind., USA) was used to measure gamma activity of irradiated samples. Acquired gamma spectra were processed by means of Genie 2000 standard software package. The σ(E) functions and neutron spectra were calculated by using the least squares method and approximating the tabular and experimental data with power polynomials. The developed technique was applied for the adjustment of the topazes irradiation regimes in the reactor core and under secondary neutrons flux from a nickel target in the cyclotron. The given technique allows to calculate a logarithmic spectrum of neutrons in a energy range from 0,025 eV up to 12 MeV with the uncertainty of about 10 %. (author)

Evaluation of reactor induced (n,p) reactions for activation analysis of titanium in geological materials

Energy Technology Data Exchange (ETDEWEB)

Espinosa Garcia, R; Cohen, I M [Comision Nacional de Energia Atomica, Buenos Aires (Argentina)

1984-05-01

The possibilities of reactor induced (n,p) reactions as a tool for neutron activation analysis of titanium in geological samples are discussed. The interference of calcium and scandium is experimentally evaluated. Results for Ti, Ca and Sc in GSP-1 and PCC-1 standard rocks are presented. Based on the experimental values, it is concluded that the /sup 47/Ti(n,p)/sup 47/Sc reaction is the most favourable for titanium determination. 11 refs.

Determination of 16N and 19O activities in loop water of swimming pool reactor

International Nuclear Information System (INIS)

Ding Shengyao; Xu Kun; Yu Baosheng; Ling Yude

2006-01-01

Measurements of activities for 16 N and 19 O nuclei in the loop water of swimming pool reactor at China Institute of Atomic Energy were carried out. In order to verify the experiment results, a calculation for same purpose was also performed. The results show their coincidence is well in uncertainty range. The evaluated recommendation data for 18 O(n, γ) 19 O reaction cross sections are also given in the paper. (authors)

Working Group 7.0 Environmental Transport and Health Effects, Chernobyl Studies Project. Progress report, October 1994 -- March 1995

International Nuclear Information System (INIS)

Anspaugh, L.R.; Hendrickson, S.M.

1995-01-01

This document presents the details from the working group 7.0 Chernobyl Studies Project. This working group looked at the environmental transport and health effects from the fallout due to the meltdown of Chernobylsk-4 reactor. Topics include: hydrological transport; chromosome painting dosimetry; EPR, TL and OSL dosimetry; stochastic effects; thyroid studies; and leukemia studies

Leak detection device for reactor coolant

International Nuclear Information System (INIS)

Oshima, Koichiro.

1990-01-01

In a light water cooled reactor, if reactor coolants are leaked from pipelines in a pipeline chamber, activated products (N-16) are diffused together to an atmosphere in the pipeline chamber. N-16 is sucked from an extracting tube which is always sucking the atmosphere in the pipeline chamber to a sucking blower. Then, β-rays released from N-16 are monitored by a radiation monitor in a measuring chamber which is radiation-shielded from the pipeline chamber. Accordingly, since the radiation monitor can detect even slight leakage, the slight leakage of reactor coolants in the pipelines can be detected at an early stage. (I.N.)

Efecto de la concentración de SO2 en las reacciones de calcinación y sulfatación de calcáreos en reactores de lecho fluidizado.

Directory of Open Access Journals (Sweden)

J. E. Lindo Samaniego

2008-01-01

Full Text Available Fue realizado un estudio sobre el efecto de las concentraciones de SO2 en la absorción por calcáreo en hornos de Lecho Fluidizado. Para observar la influencia del SO2 en los parámetros de diferentes procesos físicos y químicos fueron creados ambientes para cuatro concentraciones diferentes de SO2 : 500, 1000, 2000 y 4000 ppm. Se utilizaron dos tipos de calcáreos: Dolimitico-DP y el Calcítico-CI. El Lecho Fluidizado Burbujeante utilizado tiene 160 mm de diámetro interno y fue fluidizado con aire a la temperatura de 850 °C, con una concentración de SO2 deseada. Como material del lecho fue utilizada la arena de cuarzo (99,9% con diámetro de 385 µm y de masa aproximadamente 3,0 kg. El calcáreo fue adicionado en dosificación de 50 g con el reactor ya pre-calentado. Las variaciones de las concentraciones de SO2, CO2, CO, O2 y las descargas, fueron monitoreadas continuamente a la salida del ciclón que fue utilizado para la retención de la partícula fina. Para esos dados se desarrolló un programa en LabView. El modelo matemático escogido posibilitó la determinación de la conversión.A study of the effect of the concentrations of SO2 in its absorption by limestones in fluidized bed furnaces was conducted. For the determination of the SO2 influence on the different physical and chemical parameters of process, such as calcinations and sulfatation four different atmospheres were used in the reator with concentrations of SO2 of 500, 1000, 2000 and 4000 ppm. Two types of limestones were used: Dolomite-DP and Calcitic-CI. The bench scale bubbling fluidized bed reactor had a 160 mm internal diameter and was fluidized with air at 850 °C containing the required concentration of SO2. Bed material was quartz sand (99,9% , with 385 µm diameter and approximately 3 kg of mass. The limestone was introduced in samples of 50 kg in the reactor previously stabilized and their discharges in the reactor exit were continually monitored. For the

Una visión global del e.Learning y su e.Market

Directory of Open Access Journals (Sweden)

Guillermo Vázquez

Full Text Available Las Tecnologías de la Información y de la Comunicación y su aplicación en la formación y entrenamiento de los profesionales, mediante el eLearning, supone una de las grandes revoluciones que caracterizan a la Sociedad del Conocimiento. Sin embargo solo una estrategia global que encare todas sus facetas simultáneamente puede acompasar el desarrollo tecnológico y su implementación efectiva. En este artículo los autores subrayan en primer lugar la importancia del liderazgo en la fase actual de implantación y aceptación del eLearning, y los punto claves sobre los que se debe de sustentar. En segundo lugar explican las características de las acciones formativas online, y su engarce en un Campus Virtual. En tercer lugar se explican las características tecnológicas del eLearning. Finalmente recalcan la necesidad de un eMarket para asegurar que lo altos costes de una nueva metodología, son sostenibles.

Una visión global del e.Learning y su e.Market

Directory of Open Access Journals (Sweden)

Guillermo Vázquez

2006-12-01

Full Text Available Las Tecnologías de la Información y de la Comunicación y su aplicación en la formación y entrenamiento de los profesionales, mediante el eLearning, supone una de las grandes revoluciones que caracterizan a la Sociedad del Conocimiento. Sin embargo solo una estrategia global que encare todas sus facetas simultáneamente puede acompasar el desarrollo tecnológico y su implementación efectiva. En este artículo los autores subrayan en primer lugar la importancia del liderazgo en la fase actual de implantación y aceptación del eLearning, y los punto claves sobre los que se debe de sustentar. En segundo lugar explican las características de las acciones formativas online, y su engarce en un Campus Virtual. En tercer lugar se explican las características tecnológicas del eLearning. Finalmente recalcan la necesidad de un eMarket para asegurar que lo altos costes de una nueva metodología, son sostenibles.

FBR type reactor

International Nuclear Information System (INIS)

Hayase, Tamotsu.

1991-01-01

The present invention concerns an FBR type reactor in which transuranium elements are eliminated by nuclear conversion. There are loaded reactor core fuels being charged with mixed oxides of plutonium and uranium, and blanket fuels mainly comprising depleted uranium. Further, liquid sodium is used as coolants. As transuranium elements, isotope elements of neptunium, americium and curium contained in wastes taken out from light water reactors or the composition thereof are used. The reactor core comprises a region with a greater mixing ratio and a region with a less mixing ratio of the transuranium elements. The mixing ratio of the transuranium elements is made greater for the fuels in the reactor core region at the boundary with the blanket of great neutron leakage. With such a constitution, since the positive reactivity value at the reactor core central portion is small in the Na void reactivity distribution in the reactor core, the positive reactivity is small upon Na boiling in the reactor core central region upon occurrence of imaginable accident, to attain reactor safety. (I.N.)

Effect of temperature on two-phase anaerobic reactors treating slaughterhouse wastewater

Directory of Open Access Journals (Sweden)

Simone Beux

2007-11-01

Full Text Available The effectiveness of the anaerobic treatment of effluent from a swine and bovine slaughterhouse was assessed in two sets of two-phase anaerobic digesters, operated with or without temperature control. Set A, consisting of an acidogenic reactor with recirculation and an upflow biological filter as the methanogenic phase, was operated at room temperature, while set B, consisting of an acidogenic reactor without recirculation and an upflow biological filter as the methanogenic phase, was maintained at 32°C. The methanogenic reactors showed COD (Chemical Demand of Oxygen removal above 60% for HRT (Hydraulic Retention Time values of 20, 15, 10, 8, 6, 4, and 2 days. When the HRT value in those reactors was changed to 1 day, the COD percentage removal decreased to 50%. The temperature variations did not have harmful effects on the performance of reactors in set A.Avaliou-se a eficiência do tratamento anaeróbio de efluente de matadouro de suínos e bovinos em dois conjuntos de biodigestores anaeróbios de duas fases, operados com e sem controle de temperatura. O conjunto A, formado por um reator acidogênico com recirculação e um filtro biológico de fluxo ascendente, foi operado a temperatura ambiente e o conjunto B, formado por um reator de fluxo ascendente e um filtro biológico de fluxo ascendente, foi mantido a 32°C. Os reatores metanogênicos apresentaram remoção de DQO acima de 60 % para os TRHs de 20, 15, 10, oito, seis, quatro e dois dias. Quando o TRH destes reatores foi mudado para um dia observou-se uma queda da porcentagem de remoção de DQO para 50 %. As variações de temperatura parecem não ter prejudicado o desempenho dos reatores do conjunto A.

Plutonium-burn high temperature gas-cooled reactor for 3E+3S

International Nuclear Information System (INIS)

Okamoto, Koji

2015-01-01

The Nuclear Energy Development in Japan is facing a very difficult conditions after Fukushima-Daiichi NPP Accident. Nuclear Energy has strong advantages on 3E, i.e., Energy security, Economical efficiency and Environment. However, people does not believe the Safety 'S' of Nuclear Energy, now. The disadvantage of 'S' overrides the advantages of '3E'. In Nuclear Energy, 'S' is expanded into 3S, i.e., Safety, Security and Safeguards. Especially, the management of Plutonium inventory in Spent Fuel generated by the NPP operation is very important in the viewpoints of non-proliferation. The high-temperature gas cooled reactor (HTGR) is the solution of these disadvantages of '3S' in Nuclear Energy. The fuel of HTGR is composed by 1 mm spherical fuel particle, i.e., TRISO made by fuel, graphite and silicon-carbide. The silicon-carbide can confine the fission products in any conditions of fuel life cycle, i.e., during operation, accidents and disposal for 1 million years. The confinement of the radioactive materials can be confirmed by the TRISO. The HTGR core has strong negative feedback for temperature. So, the fission automatically stopped at the accidental conditions, such as loss of flow and LOCA. Also, the residual heat can be cooled by the radiation heat transfer to reactor vessel wall. The HTGR system usually has passive vessel wall cooling system. When the passive cooling system had been failed, the heat can be transferred to the land by heat conductions, and fuel does not reach the SiC broken temperature. The fission chain reaction has been stopped automatically by negative feedback, i.e., physics. The residual heat had been cooled automatically by radiation. The radioactive materials had been confined automatically by silicon-carbide. The HTGR is superior for 'S' safety. Plutonium can be burned by the HTGR. In the viewpoints of non-proliferation, the fuel should be made by YSZ-PuO 2 , stabilized buffer

Neutron cross-sections for next generation reactors: New data from n_TOF

CERN Document Server

Colonna, N; Eleftheriadis, C; Leeb, H; Tain, J L; Calvino, F; Herrera-Martinez, A; Savvidis, I; Vlachoudis, V; Haas, B; Abbondanno, U; Vannini, G; Konovalov, V; Marques, L; Wiescher, M; de Albornoz, A Carrillo; Audouin, L; Mengoni, A; Quesada, J; Becvar, F; Plag, R; Cennini, P; Mosconi, M; Duran, I; Rauscher, T; Ketlerov, V; Couture, A; Capote, R; Sarchiapone, L; Pigni, M T; Vlastou, R; Domingo-Pardo, C; Pavlopoulos, P; Karamanis, D; Krticka, M; Jericha, E; Ferrari, A; Martinez, T; Oberhummer, H; Karadimos, D; Plompen, A; Isaev, S; Terlizzi, R; Kaeppeler, F; Cortes, G; Cox, J; Voss, F; Pretel, C; Berthoumieux, E; Dolfini, R; Vaz, P; Griesmayer, E; Heil, M; Lopes, I; Lampoudis, C; Walter, S; Calviani, M; Gonzalez-Romero, E; Stephan, C; Igashira, M; Papachristodoulou, C; Aerts, G; Tavora, L; Wendler, H; Milazzo, P M; Rudolf, G; Andrzejewski, J; Villamarin, D; Ferreira-Marques, R; O'Brien, S; Gunsing, F; Reifarth, R; Perrot, L; Lindote, A; Neves, F; Poch, A; Gramegna, F; Kerveno, M; Rubbia, C; Koehler, P; Dahlfors, M; Wisshak, K; Fujii, K; Salgado, J; Dridi, W; Ventura, A; Andriamonje, S; Dillman, I; Assimakopoulos, P; Ferrant, L; Lozano, M; Patronis, N; Chiaveri, E; Guerrero, C; Kadi, Y; Baumann, P; Moreau, C; Oshima, M; Rullhusen, P; Furman, W; David, S; Marrone, S; Paradela, C; Vicente, M C; Tassan-Got, L; Cano-Ott, D; Alvarez-Velarde, F; Massimi, C; Mastinu, P; Pancin, J; Papadopoulos, C; Tagliente, G; Alvarez, H; Haight, R; Goverdovski, A; Chepel, V; Rosetti, M; Kossionides, E; Badurek, G; Marganiec, J; Lukic, S; Frais-Koelbl, H; Pavlik, A; Goncalves, I

2010-01-01

In 2002, an innovative neutron time-of-flight facility started operation at CERN: n\\_TOF. The main characteristics that make the new facility unique are the high instantaneous neutron flux, high resolution and wide energy range. Combined with state-of-the-art detectors and data acquisition system, these features have allowed to collect high accuracy neutron cross-section data on a variety of isotopes, many of which radioactive, of interest for Nuclear Astrophysics and for applications to advanced reactor technologies. A review of the most important results on capture and fission reactions obtained so far at n\\_TOF is presented, together with plans for new measurements related to nuclear industry. (C) 2010 Elsevier Ltd. All rights reserved.

Evaluation of Some (n,n'), (n,γ), (n,p), (n,2n) and (n,3n) Reaction Excitation Functions for Fission and Fusion Reactor Dosimetry Applications; Evaluation of the Excitation Functions for the 54Fe(n,p)54Mn, 58Ni(n,2n)57Ni, 67Zn(n,p)67Cu, 92Mo(n,p)92mNb, 93Nb(n,γ)94Nb, 113In(n,n')113mIn, 115In(n,γ) 116mIn, and 169Tm(n,3n)167Tm Reactions. Progress Report on Research Contract No 16242

International Nuclear Information System (INIS)

Zolotarev, K.I.; Zolotarev, P.K.

2013-12-01

Cross section data for the 54 Fe(n,p) 54 Mn, 58 Ni(n,2n) 57 Ni, 67 Zn(n,p) 67 Cu, 92 Mo(n,p) 92m Nb, 93 Nb(n,γ) 94 Nb, 113 In(n,n') 113m In, 115 In(n,γ) 116m In, 169 Tm(n,3n) 167 Tm reactions are needed to solve a wide spectrum of scientific and technical tasks. Activation detectors based on these reactions may be used in the field of reactor dosimetry. Furthermore, the 54 Fe(n,p) 54 Mn reaction is often used in experimental nuclear physics as a monitor reaction for measurements of unknown cross sections by means of the activation method over the neutron energy range from 5 to 15 MeV. The 93 Nb(n,γ) 94 Nb reaction is also very promising for using in retrospective neutron dosimetry for determination of total neutron fluence during a campaign of a reactor. In the existing version of the International Reactor Dosimetry File and the new extended version named as IRDFF data for excitation functions of 67 Zn(n,p) 67 Cu, 92 Mo(n,p) 92m Nb, 113 In(n,n') 113m In, and 169 Tm(n,3n) 167 Tm reactions are absent. Data for these reactions are also absent in the JENDL/D-99 dosimetry file. Excitation functions of 67 Zn(n,p) 67 Cu and 169 Tm(n,3n) 167 Tm are presented in the TENDL-2012, EAF-2010, JENDL-4.0, JEFF-3.1/A, MENDL-2 libraries. Cross section data for the 67 Zn(n,p) 67 Cu reaction up to 20 MeV are given also in the JENDL/HE-2007 library. Excitation functions of the 92 Mo(n,p) 92m Nb and 113 In(n,n') 113m In reactions are evaluated in the EAF-2010 and JEFF-3.1/A libraries. Cross section data for the 113 In(n,n') 113m In reaction are given also in the TENDL-2010 library. It is necessary to note that neutron data in the JEFF-3.1/A and JENDL-4.0 libraries were evaluated up to 20 MeV. Neutron data in the TENDL-2012, EAF-2010, MENDL-2 and TENDL-2010 libraries had been evaluated up to 30 MeV, 60 MeV, 100 MeV and 200 MeV, respectively. Neutron cross sections in the MENDL-2, TENDL-2010 and TENDL-2012 libraries had been obtained on the basis of pure theoretical model calculations

The dynamic pressure measurements of the nuclear reactor coolant for condition-based maintenance of the reactor

International Nuclear Information System (INIS)

Es-Saheb, M.H.H.

1990-01-01

The condition-based maintenance of the nuclear reactor, by monitoring and measuring the instantaneous dynamic pressure distribution of the coolant (water) impact on the solid surfaces of the reactor during operation is presented. The behaviour of water domes (jets) produced by underwater explosions of small changes of P.E.T.N. at various depths in two different size cylindrical containers, which simulate the nuclear reactor, is investigated. Water surface domes (jets) from the underwater explosions are photographed. Depending on the depth of the charge, curved and flat top jets of up to 455 mm diameter and impact speeds of up to 70 m/sec. are observed. The instabilities in the dome surfaces are observed and the instantaneous profiles are analysed. It is found that, in all cases tested, the maximum pressure takes place at the center of the jet and could reach up to 3.0 times the on-dimensional impact pressure value. The use of their measurements, as online monitoring for condition-based maintenance and design-out maintenance is discussed. 18 refs

Reaction- and melting behaviour of LWR-core components UO2, Zircaloy and steel during the meltdown period

International Nuclear Information System (INIS)

Hofmann, P.

1976-07-01

The reaction behaviour of the UO 2 , Zircaloy-4 and austenitic steel core components was investigated as a function of temperature (till melting temperatures) under inert and oxidizing conditions. Component concentrations varied between that of Corium-A (65 wt.% UO 2 , 18% Zry, 17% steel) and that of Corium-E (35 wt.% UO 2 , 10% Zry, 55% steel). In addition, Zircaloy and stainless steel were used with different degrees of oxidation. The paper describes systematically the phases that arise during heating and melting. The integral composition of the melts and the qualitative as well as quantitative analysis of the phases present in solidified corium are given. In some cases melting points have been determined. The reaction and melting behaviour of the corium specimens strongly depends on the concentration and on the degree of oxidation of the core components. First liquid phases are formed at the Zry-steel interface at about 1,350 0 C. The maximum temperatures of about 2,500 0 C for the complete melting of the corium-specimens are well below the UO 2 melting point. Depending on the steel content and/or degree of oxidation of Zry and steel, a homogeneous metallic or oxide melt or two immiscible melts - one oxide and the other metallic - are obtained. During the melting experiments performed under inert gas conditions the chemical composition of the molten specimens generally change by evaporation losses of single elements, especially of uranium, zirconium and oxygen. The total weight losses go up to 30%; under oxidizing conditions they are substantially smaller due to the occurrence of different phases. In air or water vapor, the occurrence of the phases and the melting behaviour of the core components are strongly influenced by the oxidation rate and the oxygen supply to the surface of the melt. In the case of the hypothetical core melting accident, a heterogeneous melt (oxide and metallic) is probable after the meltdown period. (orig./RW) [de

Bioremediation of trace cobalt from simulated spent decontamination solutions of nuclear power reactors using E. coli expressing NiCoT genes

International Nuclear Information System (INIS)

Raghu, G.; Maruthi Mohan, P.; Balaji, V.; Venkateswaran, G.; Rodrigue, A.; Lyon 1 Univ., 69

2008-01-01

Removal of radioactive cobalt at trace levels (∼nM) in the presence of large excess (10 6 -fold) of corrosion product ions of complexed Fe, Cr, and Ni in spent chemical decontamination formulations (simulated effluent) of nuclear reactors is currently done by using synthetic organic ion exchangers. A large volume of solid waste is generated due to the nonspecific nature of ion sorption. Our earlier work using various fungi and bacteria, with the aim of nuclear waste volume reduction, realized up to 30% of Co removal with specific capacities calculated up to 1 μg/g in 6-24 h. In the present study using engineered Escherichia coli expressing NiCoT genes from Rhodopseudomonas palustris CGA009 (RP) and Novosphingobium aromaticivorans F-199 (NA), we report a significant increase in the specific capacity for Co removal (12 μg/g) in 1-h exposure to simulated effluent. About 85% of Co removal was achieved in a two-cycle treatment with the cloned bacteria. Expression of NiCoT genes in the E. coli knockout mutant of NiCoT efflux gene (rcnA) was more efficient as compared to expression in wild-type E. coli MC4100, JM109 and BL21 (DE3) hosts. The viability of the E. coli strains in the formulation as well as at different doses of gamma rays exposure and the effect of gamma dose on their cobalt removal capacity are determined. The potential application scheme of the above process of bioremediation of cobalt from nuclear power reactor chemical decontamination effluents is discussed. (orig.)

Final Report for the 1st Surveillance Test of the Reactor Pressure Vessel Material (Capsule 2) of Ulchin Nuclear Power Plant Unit 4

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai (and others)

2007-04-15

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 1st surveillance testing was performed completely by Korea Atomic Energy Research Institute at Daejon after the capsule was transported from Ulchin site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Ulchin Unit 4 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsule 2 is 4.306E+18n/cm{sup 2}. The bias factor, the ratio of calculation/measurement, was 0.918 for the 1st testing and the calculational uncertainty,7.0% satisfied the requirement of USNRC Reg.Guide 1.190, 20%. The best estimated neutron fluence for reactor vessel inside surface was 3.615E+18n/cm{sup 2} based on the end of 6th fuel cycle and it was predicted that the fluences of vessel inside surface at 16 and 32EFPY would reach 8.478E+18 and 1.673E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Ulchin Unit 4 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life.

Final Report for the 1st Surveillance Test of the Reactor Pressure Vessel Material (CAPSULE 2) of Ulchin Nuclear Power Plant Unit 3

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai (and others)

2006-12-15

Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 1st surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejon after the capsule was transported from Ulchin site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Ulchin unit 3 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsule 2 is 4.674E 18n/cm{sup 2}. The bias factor, the ratio of calculation/measurement, was 0.920 for the 1st testing and the calculational uncertainty,7.0% satisfied the requirement of USNRC Reg.Guide 1.190, 20%. The best estimated neutron fluence for reactor vessel inside surface was 3.913E 18n/cm{sup 2} based on the end of 6th fuel cycle and it was predicted that the fluences of vessel inside surface at 16 and 32EFPY would reach 9.249E 18 and 1.834E 19n/cm{sup 2} based on the current calculation. The result through this analysis for Ulchin unit 3 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life.

Reactor core for FBR type reactor

International Nuclear Information System (INIS)

Fujita, Tomoko; Watanabe, Hisao; Kasai, Shigeo; Yokoyama, Tsugio; Matsumoto, Hiroshi.

1996-01-01

In a gas-sealed assembly for a FBR type reactor, two or more kinds of assemblies having different eigen frequency and a structure for suppressing oscillation of liquid surface are disposed in a reactor core. Coolant introduction channels for introducing coolants from inside and outside are disposed in the inside of structural members of an upper shielding member to form a shielding member-cooling structure in the reactor core. A structure for promoting heat conduction between a sealed gas in the assembly and coolants at the inner side or the outside of the assembly is disposed in the reactor core. A material which generates heat by neutron irradiation is disposed in the assembly to heat the sealed gases positively by radiation heat from the heat generation member also upon occurrence of power elevation-type event to cause temperature expansion. Namely, the coolants flown out from or into the gas sealed-assemblies cause differential fluctuation on the liquid surface, and the change of the capacity of a gas region is also different on every gas-sealed assemblies thereby enabling to suppress fluctuation of the reactor power. Pressure loss is increased by a baffle plate or the like to lower the liquid surface of the sodium coolants or decrease the elevating speed thereof thereby suppressing fluctuation of the reactor power. (N.H.)

Formation cross section of iron-60 with reactor neutrons in 59Fe(n, γ)60Fe reaction

International Nuclear Information System (INIS)

Sato, T.; Suzuki, T.

1993-01-01

Ingrowth of 60 Co radioactivity in an iron sample irradiated in a nuclear reactor has been measured for determination of formation cross section of 60 Fe in the 59 Fe(n, γ) 60 Fe reaction with reactor neutrons. After 5 years cooling, the irradiated iron was purified from 60 Co and other radioactive nuclides by an anion exchange separation method and isopropyl ether extraction in hydrochloric acid. The amount of 60 Co ingrowth was measured by γ-spectrometry using a Ge-detector coupled to a multichannel pulse height analyzer 4 years after the purification of iron. Neutron flux of the irradiation position was calculated from the amount of 55 Fe produced. The observed value of 12.5 ± 2.8 barn is slightly greater than reported value for burnup cross section of 59 Fe(n, x)X, where x refers γ, α, d, p and 2n, and X is any nuclide produced by the above reactions. (author) 8 refs.; 2 tabs

Assessment of torsatrons as reactors

International Nuclear Information System (INIS)

Lyon, J.F.; Painter, S.L.

1992-12-01

Stellarators have significant operational advantages over tokamaks as ignited steady-state reactors because stellarators have no dangerous disruptions and no need for continuous current drive or power recirculated to the plasma, both easing the first wall, blanket, and shield design; less severe constraints on the plasma parameters and profiles; and better access for maintenance. This study shows that a reactor based on the torsatron configuration (a stellarator variant) could also have up to double the mass utilization efficiency (MUE) and a significantly lower cost of electricity (COE) than a conventional tokamak reactor (ARIES-I) for a range of assumptions. Torsatron reactors can have much smaller coil systems than tokamak reactors because the coils are closer to the plasma and they have a smaller cross section (higher average current density because of the lower magnetic field). The reactor optimization approach and the costing and component models are those used in the current stage of the ARIES-I tokamak reactor study. Typical reactor parameters for a 1-GW(e) Compact Torsatron reactor example are major radius R 0 = 6.6-8.8 m, on-axis magnetic field B 0 = 4.8-7.5 T, B max (on coils) = 16 T, MUE 140-210 kW(e)/tonne, and COE (in constant 1990 dollars) = 67-79 mill/kW(e)h. The results are relatively sensitive to assumptions on the level of confinement improvement and the blanket thickness under the inboard half of the helical windings but relatively insensitive to other assumptions

RELACIÓN DE LA INTENCIÓN E IDEACIÓN SUICIDA CON ALGUNAS VARIABLES

Directory of Open Access Journals (Sweden)

Paola Valderrama

2006-06-01

Full Text Available El objetivo de este estudio fue hallar la relación de la intención e ideación suicida con algunas variables sociodemográficas, las características de la enfermedad, el tratamiento antirretroviral y los aspectos piscoafectivos en personas con el VIH/SIDA que residen en Bogotá (Colombia y pertenecientes a una fundación. Para ello, se tomó una muestra de 75 pacientes con VIH positivo a quienes se evaluó a través de una entrevista semiestructurada y dos instrumentos: el inventario de depresión de Beck (IBD y la escala de Ideación Suicida (SSI. Los resultados mostraron que solo 29 personas tenían ideación suicida y 10 intención suicida: De los 10 solo 2 sujetos tenían intención después del diagnóstico. Se encontró una relación estadística significativa para ideación suicida e intención suicida con edad, estrato socioeconómico, estado civil, orientación sexual, las características de la enfermedad, el tratamiento antirretroviral y los aspectos piscoafectivos.

Licensing of nuclear reactor operators

International Nuclear Information System (INIS)

1979-09-01

Recommendations are presented for the licensing of nuclear reactor operators in units licensed according to the legislation in effect. They apply to all physical persons designated by the Operating Organization of the nuclear reactor or reactors to execute any of the following functional activities: a) to manipulate the controls of a definite reactor b) to direct the authorized activities of the reactor operators licesed according to the present recommendations. (F.E.) [pt

Utilization of dE/dx approx E sup n /a dependence for DELTA E - E-spectrometer calibration

CERN Document Server

Gorpinich, O K; Jachmenov, O O

2002-01-01

The method of calibration of DELTA E - E-spectrometers by the use of known empiric form dE/dx approx E sup n /a which describes the specific energy loss of charge particles in the matter for energy calibration of DELTA E - E-spectrometer was designed.

S.E.N.S.I.B. project

International Nuclear Information System (INIS)

2006-01-01

This report presents the state of progress of all the studies which constitute at present the S.E.N.S.I.B. project. The S.E.N.S.I.B. project receives a financial participation of the Ademe. The different chapters treat the following questions: the sensitivity of territories in the deposit; the sensitivity of grounds; the sensitivity of the banks of rivers; the sensitivity of the agricultural productions; the anthropological sensitivity of territories; comparative study of the global sensitivity of two sites; uncertainties, communication, perception and representation; assessment of the contributions to the S.E.N.S.I.B. project in 2005. (N.C.)

Electric failure on the reactor n.3 of the nuclear power plant of Dampierre

International Nuclear Information System (INIS)

2007-05-01

This note of information resumes the progress of the electric failure on the reactor n.3 of the nuclear power plant of Dampierre, the organization during the incident, it establishes then a comparison with the incident arisen to Forsmark in 2006 and reminds that it lead in an inspection on behalf of the Asn which noticed that all the procedures had been respected by the operators and did not noticed any abnormality in the maintenance. This event was classified at the level 1 of the international nuclear event scale (INES). (N.C.)

Uso de detectores de neutrinos para el monitoreo de reactores nucleares Uso de detectores de neutrinos para el monitoreo de reactores nucleares

Directory of Open Access Journals (Sweden)

Gerardo Moreno

2012-02-01

Full Text Available Se estudia la factibilidad del uso de los detectores de antineutrinos para el monitoreo de reactores nucleares. Usando un modelo sencillo de cascada de fisión a dos componentes, se ilustra la dependencia del número de antineutrinos detectados a una distancia L del reactor según la composición nuclear del combustible. Se explica el principio de detección de neutrinos de reactores en base al decaimiento beta inverso y se describe como los detectores de neutrinos pueden emplearse para el monitoreo de la producción de materiales fisibles en el reactor. Se comenta como generalizar este análisis al caso real de un reactor nuclear in situ y uno de los principales experimentos internacionales dedicados a este propósito. We study the feasibility to use antineutrinos detectors for monitoring of nuclear reactors. Using a simple model of fission shower with two components, we illustrate how the numbers of antineutrinos detected at a distance L from the reactor depend on the composition of the nuclear combustible. We explain the principles of reactor neutrino detection using inverse beta decays and we describe how neutrinos detectors can be used for monitoring the production of fissile materials within the reactors. We comment how to generalize this analysis to the realistic case of a nuclear reactor in situ and one of the main international experiments dedicated to study the use of neutrinos detectors as nuclear safeguards.

Phenomenology and modeling of particulate corrosion product behavior in Hanford N Reactor primary coolant

International Nuclear Information System (INIS)

Bechtold, D.B.

1983-01-01

The levels and composition of filterable corrosion products in the Hanford N Reactor Primary Loop are measurable by filtration. The suspended crud level has ranged from 0.0005 ppM to 6.482 ppM with a median 0.050 ppM. The composition approximates magnetite. The particle size distribution has been found in 31 cases to be uniformly a log normal distribution with a count median ranging from 1.10 to 2.31 microns with a median of 1.81 microns, and the geometric standard deviation ranging from 1.60 to 2.34 with a median of 1.84. An auto-correcting inline turbidimeter was found to respond to linearly to suspended crud levels over a range 0.05 to at least 6.5 ppM by direct comparison with filter sample weights. Cause of crud bursts in the primary loop were found to be power decreases. The crud transients associated with a reactor power drop, several reactor shutdowns, and several reactor startups could be modeled consistently with each other using a simple stirred-tank, first order exchange model of particulate between makeup, coolant, letdown, and loosely adherent crud on pipe walls. Over 3/10 of the average steady running particulate crud level could be accounted for by magnetically filterable particulate in the makeup feed. A simulation model of particulate transport has been coded in FORTRAN

Engineering design of advanced marine reactor MRX

International Nuclear Information System (INIS)

1997-10-01

JAERI has studied the design of an advanced marine reactor (named as MRX), which meets requirements of the enhancement of economy and reliability, by reflecting results and knowledge obtained from the development of N.S. Mutsu. The MRX with a power of 100 MWt is intended to be used for ship propulsion such as an ice-breaker, container cargo ship and so on. After completion of the conceptual design, the engineering design was performed in four year plan from FY 1993 to 1996. (1) Compactness, light-weightiness and simplicity of the reactor system are realized by adopting an integral-type PWR, i.e. by installing the steam generator, the pressurizer, and the control rod drive mechanism (CRDM) inside the pressure vessel. Because of elimination of the primary coolant circulation pipes in the MRX, possibility of large-scale pipe break accidents can be eliminated. This contributes to improve the safety of the reactor system and to simplify the engineered safety systems. (2) The in-vessel type CRDM contributes not only to eliminate possibilities of rod ejection accidents, but also to make the reactor system compact. (3) The concept of water-filled containment where the reactor pressure vessel is immersed in the water is adopted. It can be of use for emergency core cooling system which maintains core flooding passively in case of a loss-of-coolant accident. The water-filled containment system also contributes essentially light-weightness of the reactor system since the water inside containment acts as a radiation shield and in consequence the secondary radiation shield can be eliminated. (4) Adoption of passive decay heat removal systems has contributed in a greater deal to simplification of the engineered safety systems and to enhancement of reliability of the systems. (5) Operability has been improved by simplification of the whole reactor system, by adoption of the passive safety systems, advanced automatic operation systems, and so on. (J.P.N.)

EQ6 Calculations for Chemical Degradation Of N Reactor (U-Metal) Spent Nuclear Fuel Waste Packages

International Nuclear Information System (INIS)

P. Bernot

2001-01-01

The Monitored Geologic Repository (MGR) Waste Package Department of the Civilian Radioactive Waste Management System Management and Operating Contractor (CRWMS M and O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the N Reactor, a graphite moderated reactor at the Department of Energy's (DOE) Hanford Site (ref. 1). The N Reactor core was fueled with slightly enriched (0.947 wt% and 0.947 to 1.25 wt% 235 U in Mark IV and Mark IA fuels, respectively) U-metal clad in Zircaloy-2 (Ref. 1, Sec. 3). Both types of N Reactor SNF have been considered for disposal at the proposed Yucca Mountain site. For some WPs, the outer shell and inner shell may breach (Ref. 3) allowing the influx of water. Water in the WP will moderate neutrons, increasing the likelihood of a criticality event within the WP; and the water may, in time, gradually leach the fissile components from the WP, further affecting the neutronics of the system. This study presents calculations of the long-term geochemical behavior of WPs containing two multi-canister overpacks (MCO) with either six baskets of Mark IA or five baskets of Mark IV intact N Reactor SNF rods (Ref. 1, Sec. 4) and two high-level waste (HLW) glass pour canisters (GPCs) arranged according to the codisposal concept (Ref. 4). The specific study objectives were to determine: (1) The extent to which fissile uranium will remain in the WP after corrosion/dissolution of the initial WP configuration (2) The extent to which fissile uranium will be carried out of the degraded WP by infiltrating water (such that internal criticality is no longer possible, but the possibility of external criticality may be enhanced); and (3) The nominal chemical composition for the criticality evaluations of the WP design, and to suggest the range of parametric variations for additional evaluations. The scope of this calculation, the chemical compositions (and subsequent criticality evaluations) of the simulations, is limited to

EQ6 Calculations for Chemical Degradation Of N Reactor (U-Metal) Spent Nuclear Fuel Waste Packages

Energy Technology Data Exchange (ETDEWEB)

P. Bernot

2001-02-27

The Monitored Geologic Repository (MGR) Waste Package Department of the Civilian Radioactive Waste Management System Management & Operating Contractor (CRWMS M&O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the N Reactor, a graphite moderated reactor at the Department of Energy's (DOE) Hanford Site (ref. 1). The N Reactor core was fueled with slightly enriched (0.947 wt% and 0.947 to 1.25 wt% {sup 235}U in Mark IV and Mark IA fuels, respectively) U-metal clad in Zircaloy-2 (Ref. 1, Sec. 3). Both types of N Reactor SNF have been considered for disposal at the proposed Yucca Mountain site. For some WPs, the outer shell and inner shell may breach (Ref. 3) allowing the influx of water. Water in the WP will moderate neutrons, increasing the likelihood of a criticality event within the WP; and the water may, in time, gradually leach the fissile components from the WP, further affecting the neutronics of the system. This study presents calculations of the long-term geochemical behavior of WPs containing two multi-canister overpacks (MCO) with either six baskets of Mark IA or five baskets of Mark IV intact N Reactor SNF rods (Ref. 1, Sec. 4) and two high-level waste (HLW) glass pour canisters (GPCs) arranged according to the codisposal concept (Ref. 4). The specific study objectives were to determine: (1) The extent to which fissile uranium will remain in the WP after corrosion/dissolution of the initial WP configuration (2) The extent to which fissile uranium will be carried out of the degraded WP by infiltrating water (such that internal criticality is no longer possible, but the possibility of external criticality may be enhanced); and (3) The nominal chemical composition for the criticality evaluations of the WP design, and to suggest the range of parametric variations for additional evaluations. The scope of this calculation, the chemical compositions (and subsequent criticality evaluations) of the simulations, is limited

Reactor core of nuclear reactor

International Nuclear Information System (INIS)

Sasagawa, Masaru; Masuda, Hiroyuki; Mogi, Toshihiko; Kanazawa, Nobuhiro.

1994-01-01

In a reactor core, a fuel inventory at an outer peripheral region is made smaller than that at a central region. Fuel assemblies comprising a small number of large-diameter fuel rods are used at the central region and fuel assemblies comprising a great number of smalldiameter fuel rods are used at the outer peripheral region. Since a burning degradation rate of the fuels at the outer peripheral region can be increased, the burning degradation rate at the infinite multiplication factor of fuels at the outer region can substantially be made identical with that of the fuels in the inner region. As a result, the power distribution in the direction of the reactor core can be flattened throughout the entire period of the burning cycle. Further, it is also possible to make the degradation rate of fuels at the outer region substantially identical with that of fuels at the inner side. A power peak formed at the outer circumferential portion of the reactor core of advanced burning can be lowered to improve the fuel integrity, and also improve the reactor safety and operation efficiency. (N.H.)

Calculations on neutron irradiation damage in reactor materials

International Nuclear Information System (INIS)

Sone, Kazuho; Shiraishi, Kensuke

1976-01-01

Neutron irradiation damage calculations were made for Mo, Nb, V, Fe, Ni and Cr. Firstly, damage functions were calculated as a function of neutron energy with neutron cross sections of elastic and inelastic scatterings, and (n,2n) and (n,γ) reactions filed in ENDF/B-III. Secondly, displacement damage expressed in displacements per atom (DPA) was estimated for neutron environments such as fission spectrum, thermal neutron reactor (JMTR), fast breeder reactor (MONJU) and two fusion reactors (The Conceptual Design of Fusion Reactor in JAERI and ORNL-Benchmark). then, damage cross section in units of dpa. barn was defined as a factor to convert a given neutron fluence to the DPA value, and was calculated for the materials in the above neutron environments. Finally, production rates of helium and hydrogen atoms were calculated with (n,α) and (n,p) cross sections in ENDF/B-III for the materials irradiated in the above reactors. (auth.)

Preliminary shielding design evaluation for reactor assembly of SMART

International Nuclear Information System (INIS)

Kim, Kyo Youn; Kang, Chang M.; Kim, Ha Yong; Zee, Sung Quun; Chang, Moon Hee

1999-03-01

This report describes a preliminary evaluations of SMART shielding design near the reactor core by using the DORT two-dimensional discrete ordinates transport code. The results indicate that maximum neutron fluence at the bottom of reactor vessel is 1.64x10 17 n/cm 2 and that on the radial surface of reactor vessel is 6.71x10 16 n/cm 2 . These results meet the requirement, 1.0x10 20 n/cm 2 , in 10 CFR 50.61 and the integrity of SMART reactor vessel is confirmed during the lifetime of reactor. (Author). 20 refs., 11 tabs., 8 figs