Reactivity control system of a passively safe thorium breeder pebble bed reactor

Energy Technology Data Exchange (ETDEWEB)

Wols, F.J., E-mail: f.j.wols@tudelft.nl; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2014-12-15

Highlights: • A worth of over 15,000 pcm ensures achieving long-term cold shutdown in thorium PBR. • Control rod worth in side reflector is insufficient due to low-power breeder zone. • 20 control rods, just outside the driver zone, can achieve long-term cold shutdown. • BF{sub 3} gas can be inserted for reactor shutdown, but only in case of emergency. • Perturbation theory accurately predicts absorber gas worth for many concentrations. - Abstract: This work investigates the neutronic design of the reactivity control system for a 100 MW{sub th} passively safe thorium breeder pebble bed reactor (PBR), a conceptual design introduced previously by the authors. The thorium PBR consists of a central driver zone of 100 cm radius, surrounded by a breeder zone with 300 cm outer radius. The fissile content of the breeder zone is low, leading to low fluxes in the radial reflector region. Therefore, a significant decrease of the control rod worth at this position is anticipated. The reactivity worth of control rods in the side reflector and at alternative in-core positions is calculated using different techniques, being 2D neutron diffusion, perturbation theory and more accurate 3D Monte Carlo models. Sensitivity coefficients from perturbation theory provide a first indication of effective control rod positions, while the 2D diffusion models provide an upper limit on the reactivity worth achievable at a certain radial position due to the homogeneous spreading of the absorber material over the azimuthal domain. Three dimensional forward calculations, e.g. in KENO, are needed for an accurate calculation of the total control rod worth. The two dimensional homogeneous calculations indicate that the reactivity worth in the radial reflector is by far insufficient to achieve cold reactor shutdown, which requires a control rod worth of over 15 000 pcm. Three dimensional heterogeneous KENO calculations show that placing 20 control rods just outside the driver channel

Techniques for computing reactivity changes caused by fuel axial expansion in LMR's

International Nuclear Information System (INIS)

Khalil, H.

1988-01-01

An evaluation is made of the accuracy of methods used to compute reactivity changes caused by axial fuel relocation in fast reactors. Results are presented to demonstrate the validity of assumptions commonly made such as linearity of reactivity with fuel elongation, additivity of local reactivity contributions, and the adequacy of standard perturbation techniques. Accurate prediction of the reactivity loss caused by axial swelling of metallic fuel is shown to require proper representation of the burnup dependence of the expansion reactivity. Some accuracy limitations in the methods used in transient analyses, which are based on the use of fuel worth tables, are identified, and efficient ways to improve accuracy are described. Implementation of these corrections produced expansion reactivity estimates within 5% of higher-order method for a metal-fueled FFTF core representation. 18 refs., 3 figs., 3 tabs

Nuclear reactivity control using laser induced polarization

International Nuclear Information System (INIS)

Bowman, C.D.

1990-01-01

This patent describes a control element for reactivity control of a fission source provides an atomic density of 3 He in a control volume which is effective to control criticality as the 3 He is spin-polarized. Spin-polarization of the 3 He affects the cross section of the control volume for fission neutrons and hence, the reactivity. An irradiation source is directed within the 3 He for spin-polarizing the 3 He. An alkali-metal vapor may be included with the 3 He where a laser spin-polarizes the alkali-metal atoms which in turn, spin-couple with 3 He to spin-polarize the 3 He atoms

Reactive power control with CHP plants - A demonstration

DEFF Research Database (Denmark)

Nyeng, Preben; Østergaard, Jacob; Andersen, Claus A.

2010-01-01

power rating of 7.3 MW on two synchronous generators. A closed-loop control is implemented, that remote controls the CHP plant to achieve a certain reactive power flow in a near-by substation. The solution communicates with the grid operator’s existing SCADA system to obtain measurements from...... lines to underground cables has changed the reactive power balance, and third, the TSO has introduced restrictions in the allowed exchange of reactive power between the transmission system and distribution grids (known as the Mvar-arrangement). The demonstration includes a CHP plant with an electric......In this project the potential for ancillary services provision by distributed energy resources is investigated. Specifically, the provision of reactive power control by combined heat and power plants is examined, and the application of the new standard for DER communication systems, IEC 61850...

Reactivity analysis of core distortion effects in the FFTF

International Nuclear Information System (INIS)

Knutson, B.J.

1982-01-01

An improved technique for evaluating core distortion reactivity effects was developed using reactivity analyses of two core geometry models (R-Z and HEX). This technique is incorporated into a new processor code called CORDIS. The advantages of this technique over existing reactivity models are that is preserves core heterogeneity, provides a control rod insertion effect model, uses row-dependent axial shape functions, and provides a flexible and cost efficient core distortion reactivity analysis method

Exploring the Potential for Increased Production from the Wave Energy Converter Lifesaver by Reactive Control

Directory of Open Access Journals (Sweden)

Marta Molinas

2013-07-01

Full Text Available Fred Olsen is currently testing their latest wave energy converter (WEC, Lifesaver, outside of Falmouth Bay in England, preparing it for commercial operation at the Wavehub test site. Previous studies, mostly focusing on hydrodynamics and peak to average power reduction, have shown that this device has potential for increased power extraction using reactive control. This article extends those analyses, adding a detailed model of the all-electric power take-off (PTO system, consisting of a permanent magnet synchronous generator, inverter and DC-link. Time domain simulations are performed to evaluate the PTO capabilities of the modeled WEC. However, when tuned towards reactive control, the generator losses become large, giving a very low overall system efficiency. Optimal control with respect to electrical output power is found to occur with low added mass, and when compared to pure passive loading, a 1% increase in annual energy production is estimated. The main factor reducing the effect of reactive control is found to be the minimum load-force constraint of the device. These results suggest that the Lifesaver has limited potential for increased production by reactive control. This analysis is nevertheless valuable, as it demonstrates how a wave-to-wire model can be used for investigation of PTO potential, annual energy production estimations and evaluations of different control techniques for a given WEC device.

Application of the neutron noise technique for measurement of reactivity for subcritical reactor RA-4

International Nuclear Information System (INIS)

Orso, J; Marenzana, A

2012-01-01

Reactor core RA-4 is divided into two parts that come together to start reactor. The reactor with core separate has the largest subcritical condition, this condition is more secure and therefore the reactor shutdown. In this paper measurements are made of the decay constant of the neutron prompt ' P ', using the α-Rossi and α-Feynman methods to calculate the reactivity of the reactor core for different positions. Both techniques are compared and reactivity is obtained for several position of the reactor core using the α-Rossi technical which is obtained a function that gives the reactivity depending on the separation of the core length. Both techniques are verified using a no multiplicative system. Reactivity values for different position of the core obtained by α-Rossi technique are: $[0 cm] = (-11+/-1) dollar, $[3 cm] = (-7+/-1) dollar, $[3.5 cm] (-5.5+/-0.8) dollar, $[4.2 cm] = (-3.8+/-0.3) dollar y $[4.5] = (-3.0+/-0.1) dollar (author)

Technique of nuclear reactors controls

International Nuclear Information System (INIS)

Weill, J.

1953-12-01

This report deal about 'Techniques of control of the nuclear reactors' in the goal to achieve the control of natural uranium reactors and especially the one of Saclay. This work is mainly about the measurement into nuclear parameters and go further in the measurement of thermodynamic variables,etc... putting in relief the new features required on behalf of the detectors because of their use in the thermal neutrons flux. In the domain of nuclear measurement, we indicate the realizations and the results obtained with thermal neutron detectors and for the measurement of ionizations currents. We also treat the technical problem of the start-up of a reactor and of the reactivity measurement. We give the necessary details for the comprehension of all essential diagrams and plans put on, in particular, for the reactor of Saclay. (author) [fr

A control technique for integration of DG units to the electrical networks

DEFF Research Database (Denmark)

Pouresmaeil, Edris; Miguel-Espinar, Carlos; Massot-Campos, Miquel

2013-01-01

This paper deals with a multiobjective control technique for integration of distributed generation (DG) resources to the electrical power network. The proposed strategy provides compensation for active, reactive, and harmonic load current components during connection of DG link to the grid...

Reactivity change measurements on plutonium-uranium fuel elements in hector experimental techniques and results

International Nuclear Information System (INIS)

Tattersall, R.B.; Small, V.G.; MacBean, I.J.; Howe, W.D.

1964-08-01

The techniques used in making reactivity change measurements on HECTOR are described and discussed. Pile period measurements were used in the majority of oases, though the pile oscillator technique was used occasionally. These two methods are compared. Flux determinations were made in the vicinity of the fuel element samples using manganese foils, and the techniques used are described and an error assessment made. Results of both reactivity change and flux measurements on 1.2 in. diameter uranium and plutonium-uranium alloy fuel elements are presented, these measurements being carried out in a variety of graphite moderated lattices at temperatures up to 450 deg. C. (author)

Reactive sputter deposition

CERN Document Server

Mahieu, Stijn

2008-01-01

In this valuable work, all aspects of the reactive magnetron sputtering process, from the discharge up to the resulting thin film growth, are described in detail, allowing the reader to understand the complete process. Hence, this book gives necessary information for those who want to start with reactive magnetron sputtering, understand and investigate the technique, control their sputtering process and tune their existing process, obtaining the desired thin films.

Strategies for reactive power control in wind farms with STATCOM

Energy Technology Data Exchange (ETDEWEB)

Diaz Gonzalez, Francisco [Catalonia Institute for Energy Research (IREC), Barcelona (Spain); Martinez-Rojas, Marcela [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Barcelona (Spain). Dept. d' Enginyeria Electrica; Sumper, Andreas; Gomis-Bellmunt, Oriol [Catalonia Institute for Energy Research (IREC), Barcelona (Spain); Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Barcelona (Spain). Dept. d' Enginyeria Electrica

2010-07-01

This paper presents two strategies for reactive current control in wind farms with STATCOM under fault ride-through (FRT) situations. First, the technical requirements of the Spanish and German grid codes related to the reactive current under FRT situations are presented. Second, STATCOM and its control system are introduced. Third, the modeling done of the wind farm, the STATCOM, and the network are presented. Finally, control strategies for reactive current delivered by the park to the network under FRT situations are shown. The result of the implementation of each control strategy is shown by simulation. (orig.)

Potential impact of reactive vaccination in controlling cholera ...

African Journals Online (AJOL)

Background. To contain ongoing cholera outbreaks, the World Health Organization has suggested that reactive vaccination should be considered in addition to its previous control measures. Objectives. To explore the potential impact of a hypothetical reactive oral cholera vaccination using the example of the recent ...

Probabilistic analysis on the failure of reactivity control for the PWR

Science.gov (United States)

Sony Tjahyani, D. T.; Deswandri; Sunaryo, G. R.

2018-02-01

The fundamental safety function of the power reactor is to control reactivity, to remove heat from the reactor, and to confine radioactive material. The safety analysis is used to ensure that each parameter is fulfilled during the design and is done by deterministic and probabilistic method. The analysis of reactivity control is important to be done because it will affect the other of fundamental safety functions. The purpose of this research is to determine the failure probability of the reactivity control and its failure contribution on a PWR design. The analysis is carried out by determining intermediate events, which cause the failure of reactivity control. Furthermore, the basic event is determined by deductive method using the fault tree analysis. The AP1000 is used as the object of research. The probability data of component failure or human error, which is used in the analysis, is collected from IAEA, Westinghouse, NRC and other published documents. The results show that there are six intermediate events, which can cause the failure of the reactivity control. These intermediate events are uncontrolled rod bank withdrawal at low power or full power, malfunction of boron dilution, misalignment of control rod withdrawal, malfunction of improper position of fuel assembly and ejection of control rod. The failure probability of reactivity control is 1.49E-03 per year. The causes of failures which are affected by human factor are boron dilution, misalignment of control rod withdrawal and malfunction of improper position for fuel assembly. Based on the assessment, it is concluded that the failure probability of reactivity control on the PWR is still within the IAEA criteria.

Multiagent-Based Reactive Power Sharing and Control Model for Islanded Microgrids

DEFF Research Database (Denmark)

Chen, Feixiong; Chen, Minyou; Li, Qiang

2016-01-01

of the control model, in which the uncertainty of intermittent DGs, variations in load demands, as well as impacts of time delays are considered. The simulation results demonstrate the eectiveness of the control model in proportional reactive power sharing, and the plug and play capability of the control model......In islanded microgrids (MGs), the reactive power cannot be shared proportionally among distributed generators (DGs) with conventional droop control, due to the mismatch in feeder impedances. For the purpose of proportional reactive power sharing, a multiagent system (MAS) based distributed control...

Techniques for reactive system design: the tools in TRADE

NARCIS (Netherlands)

Wieringa, Roelf J.; Jansen, D.N.; Dittrich, K.R.; Geppert, A.; Norrie, M.C.

Reactive systems are systems whose purpose is to maintain a certain desirable state of affairs in their environment, and include information systems, groupware, workflow systems, and control software. The current generation of information system design methods cannot cope with the high demands that

VAR control in distribution systems by using artificial intelligence techniques

Energy Technology Data Exchange (ETDEWEB)

Golkar, M.A. [Curtin Univ. of Technology, Sarawak (Malaysia). School of Engineering and Science

2005-07-01

This paper reviewed artificial intelligence techniques used in VAR control systems. Reactive power controls in distribution systems were also reviewed. While artificial intelligence methods are widely used in power control systems, the techniques require extensive human knowledge bases and experiences in order to operate correctly. Expert systems use knowledge and interface procedures to solve problems that often require human expertise. Expert systems often cause knowledge bottlenecks as they are unable to learn or adopt to new situations. While neural networks possess learning ability, they are computationally expensive. However, test results in recent neural network studies have demonstrated that they work well in a variety of loading conditions. Fuzzy logic techniques are used to accurately represent the operational constraints of power systems. Fuzzy logic has an advantage over other artificial intelligence techniques as it is able to remedy uncertainties in data. Evolutionary computing algorithms use probabilistic transition rules which can search complicated data to determine optimal constraints and parameters. Over 95 per cent of all papers published on power systems use genetic algorithms. It was concluded that hybrid systems using various artificial intelligence techniques are now being used by researchers. 69 refs.

Re-Active Passive devices for control of noise transmission through a panel

Science.gov (United States)

Carneal, James P.; Giovanardi, Marco; Fuller, Chris R.; Palumbo, Dan

2008-01-01

Re-Active Passive devices have been developed to control low-frequency (transmission through a panel. These devices use a combination of active, re-active, and passive technologies packaged into a single unit to control a broad frequency range utilizing the strength of each technology over its best suited frequency range. The Re-Active Passive device uses passive constrained layer damping to cover relatively high-frequency range (>150 Hz), reactive distributed vibration absorber to cover the medium-frequency range (50-200 Hz), and active control for controlling low frequencies (transmission through a panel mounted in the Transmission Loss Test Facility at Virginia Tech. Experimental results are presented for the bare panel, and combinations of passive treatment, reactive treatment, and active control. Results indicate that three Re-Active Passive devices were able to increase the overall broadband (15-1000 Hz) transmission loss by 9.4 dB. These three devices added a total of 285 g to the panel mass of 6.0 kg, or approximately 5%, not including control electronics.

Making real-time reactive systems reliable

Science.gov (United States)

Marzullo, Keith; Wood, Mark

1990-01-01

A reactive system is characterized by a control program that interacts with an environment (or controlled program). The control program monitors the environment and reacts to significant events by sending commands to the environment. This structure is quite general. Not only are most embedded real time systems reactive systems, but so are monitoring and debugging systems and distributed application management systems. Since reactive systems are usually long running and may control physical equipment, fault tolerance is vital. The research tries to understand the principal issues of fault tolerance in real time reactive systems and to build tools that allow a programmer to design reliable, real time reactive systems. In order to make real time reactive systems reliable, several issues must be addressed: (1) How can a control program be built to tolerate failures of sensors and actuators. To achieve this, a methodology was developed for transforming a control program that references physical value into one that tolerates sensors that can fail and can return inaccurate values; (2) How can the real time reactive system be built to tolerate failures of the control program. Towards this goal, whether the techniques presented can be extended to real time reactive systems is investigated; and (3) How can the environment be specified in a way that is useful for writing a control program. Towards this goal, whether a system with real time constraints can be expressed as an equivalent system without such constraints is also investigated.

Method of reactivity control in pressure tube reactor

International Nuclear Information System (INIS)

Fukumura, Nobuo.

1988-01-01

Purpose: To provide a method of controlling reactivity in a pressure tube reactor at high conversion ratio intended for high burn-up degree. Method: Control tubes are inserted in heavy water moderator. Light water is filled in the tubes at the initial burning stage. Along with the advance of the burning, the light water is gradually removed and replaced with gases of less reactive nuclear reactivity with neutrons such as air or gaseous carbon dioxide. The tubes are made of less neutron absorbing material such as aluminum. By filling light water, infinite multiplication factor is reduced to suppress the reactivity at the initial burning stage. As light water is gradually removed and replaced with air, etc., it provides an effect like that elimination of heavy water moderator to increase the conversion ratio. Accordingly, nuclear fission materials are produced additionally by so much to extend the burn-up degree. In this way, it can provide excellent effect in realizing high burn-up ratio and high conversion ratio. (Kamimura, M.)

Dynamic Reactive Power Control in Offshore HVDC Connected Wind Power Plants

DEFF Research Database (Denmark)

Sakamuri, Jayachandra N.; Cutululis, Nicolaos Antonio; Rather, Zakir Hussain

2016-01-01

This paper presents a coordinated reactive power control for a HVDC connected cluster of offshore wind power plants (WPPs). The reactive power reference for the WPP cluster is estimated by an optimization algorithm aiming at minimum active power losses in the offshore AC Grid. For each optimal......, such as wind turbine (WT) terminal, collector cable, and export cable, on the dynamic voltage profile of the offshore grid is investigated. Furthermore, the dynamic reactive power contribution from WTs from different WPPs of the cluster for such faults has also been studied....... reactive power set point, the OWPP cluster controller generates reactive power references for each WPP which further sends the AC voltage/ reactive power references to the associated WTs based on their available reactive power margin. The impact of faults at different locations in the offshore grid...

Stress reactivity to and recovery from a standardised exercise bout: a study of 31 runners practising relaxation techniques.

Science.gov (United States)

Solberg, E E; Ingjer, F; Holen, A; Sundgot-Borgen, J; Nilsson, S; Holme, I

2000-08-01

To compare the efficacy in runners of two relaxation techniques with regard to exercise reactivity and recovery after exercise. Thirty one adult male runners were studied prospectively for six months in three groups practising either meditation (n = 11) or autogenic training (n = 11) or serving as controls (n = 10). Before and after the six months relaxation intervention, indicators of reactivity to exercise and metabolism after exercise (blood lactate concentration, heart rate (HR), and oxygen consumption (VO2)), were tested immediately after and 10 minutes after exercise. Resting HR was also assessed weekly at home during the trial. State anxiety was measured before and after the intervention. After the relaxation training, blood lactate concentration after exercise was significantly (pmeditation group compared with the control group. No difference was observed in lactate responses between the autogenic training group and the control group. There were no significant differences among the groups with regard to HR, VO2, or levels of anxiety. Meditation training may reduce the lactate response to a standardised exercise bout.

Evaluation of radiation-induced sensitization using electrochemical potentiokinetic reactivation technique for austenitic stainless steels

International Nuclear Information System (INIS)

Inazumi, T.; Bell, G.E.C.; Hishinuma, A.

1990-01-01

The electrochemical potentiokinetic reactivation (EPR) test technique was applied to the determination of sensitization in a neutron-irradiated (420 degree C, 10 dpa) titanium-modified austenitic stainless steel. Miniaturized specimens (3 mm diam by 0.25 mm thick) in solution-annealed and 25% cold-worked conditions were tested. The degree of sensitization (DOS) was calculated in terms of the reactivation charge (Pa). Results indicated the occurrence of radiation-induced sensitization when compared to control specimens thermally aged at the irradiation temperature. Post-EPR examination of the specimen surfaces showed etching across the face of each grain as well as at grain boundaries. This indicates that the Pa value normalized by the total grain boundary area, which is an accepted EPR-DOS criterion, cannot be directly used as an indicator of the DOS to determine the susceptibility of this irradiated material to intergranular stress corrosion cracking (IGSCC). Further investigations are necessary to correlate the results in this study to the IGSCC susceptibility of the irradiated stainless steel. 26 refs., 7 figs., 3 tabs

The impact of fuel temperature reactivity coefficient on loss of reactivity control accident

International Nuclear Information System (INIS)

Park, J. H.; Ryu, E. H.; Song, Y. M.; Jung, J. Y.

2012-01-01

Nuclear reactors experience small power fluctuations or anticipated operational transients during even normal power operation. During normal operation, the reactivity is mainly controlled by liquid zone controllers, adjuster rods, mechanical control absorbers, and moderator poison. Even when the reactor power is increased abruptly and largely from an accident and when reactor control systems cannot be actuated quickly due to a fast transient, the reactor should be controlled and stabilized by its inherent safety parameter, such as a negative PCR (Power Coefficient of Reactivity) feedback. A PWR (Pressurized Water Reactor), it is well designed for the reactor to have a negative PCR so that the reactor can be safely shut down or stabilized whenever an abrupt reactivity insertion into the reactor core occurs or the reactor power is abruptly increased. However, it is known that a CANDU reactor has a small amount of PCR, as either negative or positive, because of the different design basis and safety concepts from a PWR. CNSC's regulatory and safety regime has stated that; The PCR of CANDU reactors does not pose a significant risk. Consistent with Canadian nuclear safety requirements, nuclear power plants must have an appropriate combination of inherent and engineered safety features incorporated into the design of the reactor safety and control systems. A reactor design that has a PCR is quite acceptable provided that the reactor is stable against power fluctuations, and that the probability and consequences of any potential accidents that would be aggravated by a positive reactivity feedback are maintained within CNSCprescribed limits. Recently, it was issued licensing the refurbished Wolsong unit 1 in Korea to be operated continuously after its design lifetime in which the calculated PCR was shown to have a small positive value by applying the recent physics code systems, which are composed of WIMS IST, DRAGON IST, and RFSP IST. These code systems were transferred

Systematic Integrated Process Design and Control of Binary Element Reactive Distillation Processes

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2016-01-01

In this work, integrated process design and control of reactive distillation processes is considered through a computer-aided framework. First, a set of simple design methods for reactive distillation column that are similar in concept to non-reactive distillation design methods are extended...... to design-control of reactive distillation columns. These methods are based on the element concept where the reacting system of compounds is represented as elements. When only two elements are needed to represent the reacting system of more than two compounds, a binary element system is identified....... It is shown that the same design-control principles that apply to a non-reacting binary system of compounds are also valid for a reactive binary system of elements for distillation columns. Application of this framework shows that designing the reactive distillation process at the maximum driving force...

Multiagent voltage and reactive power control system

Directory of Open Access Journals (Sweden)

I. Arkhipov

2014-12-01

Full Text Available This paper is devoted to the research of multiagent voltage and reactive power control system development. The prototype of the system has been developed by R&D Center at FGC UES (Russia. The control system architecture is based on the innovative multiagent system theory application that leads to the achievement of several significant advantages (in comparison to traditional control systems implementation such as control system efficiency enhancement, control system survivability and cyber security.

Analytical estimation of control rod shadowing effect for excess reactivity measurement of HTTR

International Nuclear Information System (INIS)

Nakano, Masaaki; Fujimoto, Nozomu; Yamashita, Kiyonobu

1999-01-01

The fuel addition method is generally used for the excess reactivity measurement of the initial core. The control rod shadowing effect for the excess reactivity measurement has been estimated analytically for High Temperature Engineering Test Reactor (HTTR). 3-dimensional whole core analyses were carried out. The movements of control rods in measurements were simulated in the calculation. It was made clear that the value of excess reactivity strongly depend on combinations of measuring control rods and compensating control rods. The differences in excess reactivity between combinations come from the control rod shadowing effect. The shadowing effect is reduced by the use of plural number of measuring and compensating control rods to prevent deep insertion of them into the core. The measured excess reactivity in the experiments is, however, smaller than the estimated value with shadowing effect. (author)

Use of reactivity constraints for the automatic control of reactor power

International Nuclear Information System (INIS)

Bernard, J.A.; Lanning, D.D.; Ray, A.

1985-01-01

A theoretical framework for the automatic control of reactor power has been developed and experimentally evaluated on the 5 MWt Research Reactor that is operated by the Massachusetts Institute of Technology. The controller functions by restricting the net reactivity so that it is always possible to make the reactor period infinite at the desired termination point of a transient by reversing the direction of motion of whatever control mechanism is associated with the controller. This capability is formally designated as ''feasibility of control''. It has been shown experimentally that maintenance of feasibility of control is a sufficient condition for the automatic control of reactor power. This research should be of value in the design of closed-loop controllers, in the creation of reactivity displays, in the provision of guidance to operators regarding the timing of reactivity changes, and as an experimental envelope within which alternate control strategies can be evaluated

Further development of the Dynamic Control Assemblies Worth Measurement Method for Advanced Reactivity Computers

International Nuclear Information System (INIS)

Petenyi, V.; Strmensky, C.; Jagrik, J.; Minarcin, M.; Sarvaic, I.

2005-01-01

The dynamic control assemblies worth measurement technique is a quick method for validation of predicted control assemblies worth. The dynamic control assemblies worth measurement utilize space-time corrections for the measured out of core ionization chamber readings calculated by DYN 3D computer code. The space-time correction arising from the prompt neutron density redistribution in the measured ionization chamber reading can be directly applied in the advanced reactivity computer. The second correction concerning the difference of spatial distribution of delayed neutrons can be calculated by simulation the measurement procedure by dynamic version of the DYN 3D code. In the paper some results of dynamic control assemblies worth measurement applied for NPP Mochovce are presented (Authors)

Preparation and comparison of a-C:H coatings using reactive sputter techniques

Energy Technology Data Exchange (ETDEWEB)

Keunecke, M., E-mail: martin.keunecke@ist.fraunhofer.d [Fraunhofer Institute for Surface Engineering and Thin Films (IST), Braunschweig (Germany); Weigel, K.; Bewilogua, K. [Fraunhofer Institute for Surface Engineering and Thin Films (IST), Braunschweig (Germany); Cremer, R.; Fuss, H.-G. [CemeCon AG, Wuerselen (Germany)

2009-12-31

Amorphous hydrogenated carbon (a-C:H) coatings are widely used in several industrial applications. These coatings commonly will be prepared by plasma activated chemical vapor deposition (PACVD). The main method used to prepare a-C:H coating in industrial scale is based on a glow discharge in a hydrocarbon gas like acetylene or methane using a substrate electrode powered with medium frequency (m.f. - some 10 to 300 kHz). Some aims of further development are adhesion improvement, increase of hardness and high coating quality on complex geometries. A relatively new and promising technique to fulfil these requirements is the deposition of a-C:H coatings by a reactive d.c. magnetron sputter deposition from a graphite target with acetylene as reactive gas. An advancement of this technique is the deposition in a pulsed magnetron sputter process. Using these three mentioned techniques a-C:H coatings were prepared in the same deposition machine. For adhesion improvement different interlayer systems were applied. The effect of different substrate bias voltages (d.c. and d.c. pulse) was investigated. By applying the magnetron sputter technique in the d.c. pulse mode, plastic hardness values up to 40 GPa could be reached. Besides hardness other mechanical properties like resistance against abrasive wear were measured and compared. Cross sectional SEM images showed the growth structure of the coatings.

Basic study on dynamic reactive-power control method with PV output prediction for solar inverter

Directory of Open Access Journals (Sweden)

Ryunosuke Miyoshi

2016-01-01

Full Text Available To effectively utilize a photovoltaic (PV system, reactive-power control methods for solar inverters have been considered. Among the various methods, the constant-voltage control outputs less reactive power compared with the other methods. We have developed a constant-voltage control to reduce the reactive-power output. However, the developed constant-voltage control still outputs unnecessary reactive power because the control parameter is constant in every waveform of the PV output. To reduce the reactive-power output, we propose a dynamic reactive-power control method with a PV output prediction. In the proposed method, the control parameter is varied according to the properties of the predicted PV waveform. In this study, we performed numerical simulations using a distribution system model, and we confirmed that the proposed method reduces the reactive-power output within the voltage constraint.

CpG methylation controls reactivation of HIV from latency.

Directory of Open Access Journals (Sweden)

Jana Blazkova

2009-08-01

Full Text Available DNA methylation of retroviral promoters and enhancers localized in the provirus 5' long terminal repeat (LTR is considered to be a mechanism of transcriptional suppression that allows retroviruses to evade host immune responses and antiretroviral drugs. However, the role of DNA methylation in the control of HIV-1 latency has never been unambiguously demonstrated, in contrast to the apparent importance of transcriptional interference and chromatin structure, and has never been studied in HIV-1-infected patients. Here, we show in an in vitro model of reactivable latency and in a latent reservoir of HIV-1-infected patients that CpG methylation of the HIV-1 5' LTR is an additional epigenetic restriction mechanism, which controls resistance of latent HIV-1 to reactivation signals and thus determines the stability of the HIV-1 latency. CpG methylation acts as a late event during establishment of HIV-1 latency and is not required for the initial provirus silencing. Indeed, the latent reservoir of some aviremic patients contained high proportions of the non-methylated 5' LTR. The latency controlled solely by transcriptional interference and by chromatin-dependent mechanisms in the absence of significant promoter DNA methylation tends to be leaky and easily reactivable. In the latent reservoir of HIV-1-infected individuals without detectable plasma viremia, we found HIV-1 promoters and enhancers to be hypermethylated and resistant to reactivation, as opposed to the hypomethylated 5' LTR in viremic patients. However, even dense methylation of the HIV-1 5'LTR did not confer complete resistance to reactivation of latent HIV-1 with some histone deacetylase inhibitors, protein kinase C agonists, TNF-alpha, and their combinations with 5-aza-2deoxycytidine: the densely methylated HIV-1 promoter was most efficiently reactivated in virtual absence of T cell activation by suberoylanilide hydroxamic acid. Tight but incomplete control of HIV-1 latency by Cp

Calculation of reactivity of control rods in graphite moderated reactors

International Nuclear Information System (INIS)

Nakata, H.

1978-01-01

A study about the method of calculation for the reactivity of control rods in graphite-moderated critical assemblies, is presented. The result of theoretical calculation, developed by super celles and Nordheim-Scalettar methods are compared with experimental results for the critical Assembly of General Atomic. The two methods are then applicable to reactivity calculation of the control rods of graphite moderated critical assemblies [pt

Measurements and calculation of reactivity in the IEA-R1 nuclear reactor

International Nuclear Information System (INIS)

Ferreira, P.S.B.

1988-01-01

Techniques and experimentals procedures utilized in the measurement of some nuclear parameters related to reactivity are presented. Measurements of reactivity coefficients, such as void, temperature and power, and control rod worth were made in the IEA-R1 Research Reactor. The techniques used to perform the measurements were: i) stable period (control rod calibration), ii) inverse kinetics (digital reactivity meter), iii) aluminium slab insertion in the fuel element coolant channels (void reactivity), iv) nuclear reactor core temperature changes by means of the changes in the coolant systems of reactor core (isothermal reactivity coefficient) and v) by making perturbation in the core through the control rod motions (power reactivity coefficient and control rod calibration). By using the computer codes HAMMER, HAMMER-TECHNION and CITATION, the experiments realized in the IEA-R1 reactor were simulated. From this simulation, the theoretical reactivity parameters were estimated and compared with the respective experimental results. Furthermore, in the second fuel load of Angra-1 Nuclear Power Station, the IPEN-CNEN/SP digital reactivity - meter were used in the lower power test with the aim to assess the equipment performance. Among several tests, the reacticity-meter were used in parallel with a Westinghouse analogic reativimeter-meter) to measure the heat additiona point, critical boron concentration, control rod calibration, isothermal and moderator reactivity coefficient. These tests, and the results obtained by the digital reactivity-meter are described. The results were compared with those obtained by Westinghouse analogic reactivity meter, showing excellent agreement. (author) [pt

Automated reactivity anomaly surveillance in the Fast Flux Test Facility

International Nuclear Information System (INIS)

Knutson, B.J.; Harris, R.A.; Honeyman, D.J.; Shook, A.T.; Krohn, C.N.

1985-01-01

The automated technique for monitoring core reactivity during power operation used at the Fast Flux Test Facility (FFTF) is described. This technique relies on comparing predicted to measured rod positions to detect any anomalous (or unpredicted) core reactivity changes. It is implemented on the Plant Data System (PDS) computer and, thus, provides rapid indication of any abnormal core conditions. The prediction algorithms use thermal-hydraulic, control rod position and neutron flux sensor information to predict the core reactivity state

Associations between Effortful Control, Psychological Control and Proactive and Reactive Aggression

Science.gov (United States)

Rathert, Jamie; Fite, Paula J.; Gaertner, Alden E.

2011-01-01

The current study examined relations between effortful control (ones ability to focus and shift attention in an adaptive manner), psychological control (caregiver attempts to manipulate the child's internal world) and proactive and reactive aggression. Participants were 69 children (54% male) ranging from 9 to 12 years of age (M = 10.35, SD =…

Development of automated controller system for controlling reactivity by using FPGA in research reactor application

International Nuclear Information System (INIS)

Mohd Sabri Minhat; Izhar Abu Hussin; Mohd Idris Taib

2012-01-01

The scope for this research paper is to produce a detail design for Development of Automated Controller System for Controlling Reactivity by using FPGA in Research Reactor Application for high safety nuclear operation. The development of this project including design, purchasing, fabrication, installation, testing and validation and verification for one prototype automated controller system for controlling reactivity in industry local technology for human capacity and capability development towards the first Nuclear Power Programme (NPP) in Malaysia. The specific objectives of this research paper are to Development of Automated Controller System for Controlling Reactivity (ACSCR) in Research Reactor Application (PUSPATI TRIGA Reactor) by using simultaneous movement method; To design, fabricate and produce the accuracy of Control Rods Drive Mechanism to 0.1 mm resolution using a stepper motor as an actuator; To design, install and produce the system response to be more faster by using Field Programmable Gate Array (FPGA) and High Speed Computer; and to improve the Safety Level of the Research Reactor in high safety nuclear operation condition. (author)

Combined Active and Reactive Power Control of Wind Farms based on Model Predictive Control

DEFF Research Database (Denmark)

Zhao, Haoran; Wu, Qiuwei; Wang, Jianhui

2017-01-01

This paper proposes a combined wind farm controller based on Model Predictive Control (MPC). Compared with the conventional decoupled active and reactive power control, the proposed control scheme considers the significant impact of active power on voltage variations due to the low X=R ratio...... of wind farm collector systems. The voltage control is improved. Besides, by coordination of active and reactive power, the Var capacity is optimized to prevent potential failures due to Var shortage, especially when the wind farm operates close to its full load. An analytical method is used to calculate...... the sensitivity coefficients to improve the computation efficiency and overcome the convergence problem. Two control modes are designed for both normal and emergency conditions. A wind farm with 20 wind turbines was used to verify the proposed combined control scheme....

Integrated Process Design and Control of Multi-element Reactive Distillation Processes

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2016-01-01

In this work, integrated process design and control of reactive distillation processes involving multi-elements is presented. The reactive distillation column is designed using methods and tools which are similar in concept to non-reactive distillation design methods, such as driving force approach....... The methods employed in this work are based on equivalent element concept. This concept facilitates the representation of a multi-element reactive system as equivalent binary light and heavy key elements. First, the reactive distillation column is designed at the maximum driving force where through steady...

Abnormal proactive and reactive cognitive control during conflict processing in major depression.

Science.gov (United States)

Vanderhasselt, Marie-Anne; De Raedt, Rudi; De Paepe, Annick; Aarts, Kristien; Otte, Georges; Van Dorpe, Jan; Pourtois, Gilles

2014-02-01

According to the Dual Mechanisms of Control framework, cognitive control consists of two complementary components: proactive control refers to anticipatory maintenance of goal-relevant information, whereas reactive control acts as a correction mechanism that is activated when a conflict occurs. Possibly, the well-known diminished inhibitory control in response to negative stimuli in Major Depressive Disorder (MDD) patients stems from a breakdown in proactive control, and/or anomalies in reactive cognitive control. In our study, MDD patients specifically showed increased response latencies when actively inhibiting a dominant response to a sad compared with a happy face. This condition was associated with a longer duration of a dominant ERP topography (800-900 ms poststimulus onset) and a stronger activity in the bilateral dorsal anterior cingulate cortex, reflecting abnormal reactive control when inhibiting attention to a negative stimulus. Moreover, MDD patients showed abnormalities in proactive cognitive control when preparing for the upcoming imperative stimulus (abnormal modulation of the contingent negative variation component), accompanied by more activity in brain regions belonging to the default mode network. All together, deficits to inhibit attention to negative information in MDD might originate from an abnormal use of both proactive resources and reactive control processes. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Integrated Process Design and Control of Reactive Distillation Processes

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2015-01-01

on the element concept, which is used to translate a system of compounds into elements. The operation of the reactive distillation column at the highest driving force and other candidate points is analyzed through analytical solution as well as rigorous open-loop and closed-loop simulations. By application...... of this approach, it is shown that designing the reactive distillation process at the maximum driving force results in an optimal design in terms of controllability and operability. It is verified that the reactive distillation design option is less sensitive to the disturbances in the feed at the highest driving...

Reactive Nanocomposites for Controllable Adhesive Debonding

Science.gov (United States)

2011-08-01

technologies include shape memory alloy (SMA)-based approach, a chemical foaming agent (CFA) approach, and a reactive nanocomposite (RNC) approach. SMA...anofoil (a) Component 1 Thermoset Adhesive Component 2 Nano-coating (b) Figure 2. Debonding approach where (a) freestanding...J. Controlled Adhesive Debonding of RAH-66 Comanche Chines Using Shape Memory Alloys ; ARL-TR-2937; U.S. Army Research Laboratory: Aberdeen Proving

Re-active Passive (RAP) Devices for Control of Noise Transmission through a Panel

Science.gov (United States)

Carneal, James P.; Giovanardi, Marco; Fuller, Chris R.; Palumbo, Daniel L.

2008-01-01

Re-Active Passive (RAP) devices have been developed to control low frequency (transmission through a panel. These devices use a combination of active, re-active, and passive technologies packaged into a single unit to control a broad frequency range utilizing the strength of each technology over its best suited frequency range. The RAP device uses passive constrained layer damping to cover the relatively high frequency range (>200 Hz), reactive distributed vibration absorber) to cover the medium frequency range (75 to 250 Hz), and active control for controlling low frequencies (transmission through a panel mounted in a transmission loss test facility. Experimental results are presented for the bare panel, and combinations of passive treatment, reactive treatment, and active control. Results indicate that three RAP devices were able to increase the overall broadband (15-1000 Hz) transmission loss by 9.4 dB. These three devices added a total of 285 grams to the panel mass of 6.0 kg, or approximately 5%, not including control electronics.

Temperature and Stresses Estimation in Reactivity Control Rods for CAREM-25 Reactor

International Nuclear Information System (INIS)

Markiewicz, Mario; Estevez, Esteban

2000-01-01

The reactivity control rods are a critical component regarding safety.Its correct operation when required must be ensured.For this purpose, this component must maintain its operating capacity during all its residence time and under any foreseen operation condition.To evaluate the behaviour of reactivity control rods, it is necessary to analyse the demands they are exposed to, determining from the mechanical point of view, the residence time in the reactor core.In this report, using analytical calculations, the parameters affecting the performance of the reactivity control rods are analysed, with the objective of determine from the mechanical point of view, its behaviour and residence time

Combustion Mode Design with High Efficiency and Low Emissions Controlled by Mixtures Stratification and Fuel Reactivity

Directory of Open Access Journals (Sweden)

Hu eWang

2015-08-01

Full Text Available This paper presents a review on the combustion mode design with high efficiency and low emissions controlled by fuel reactivity and mixture stratification that have been conducted in the authors’ group, including the charge reactivity controlled homogeneous charge compression ignition (HCCI combustion, stratification controlled premixed charge compression ignition (PCCI combustion, and dual-fuel combustion concepts controlled by both fuel reactivity and mixture stratification. The review starts with the charge reactivity controlled HCCI combustion, and the works on HCCI fuelled with both high cetane number fuels, such as DME and n-heptane, and high octane number fuels, such as methanol, natural gas, gasoline and mixtures of gasoline/alcohols, are reviewed and discussed. Since single fuel cannot meet the reactivity requirements under different loads to control the combustion process, the studies related to concentration stratification and dual-fuel charge reactivity controlled HCCI combustion are then presented, which have been shown to have the potential to achieve effective combustion control. The efforts of using both mixture and thermal stratifications to achieve the auto-ignition and combustion control are also discussed. Thereafter, both charge reactivity and mixture stratification are then applied to control the combustion process. The potential and capability of thermal-atmosphere controlled compound combustion mode and dual-fuel reactivity controlled compression ignition (RCCI/highly premixed charge combustion (HPCC mode to achieve clean and high efficiency combustion are then presented and discussed. Based on these results and discussions, combustion mode design with high efficiency and low emissions controlled by fuel reactivity and mixtures stratification in the whole operating range is proposed.

Working principle and structure characteristics analysis of the reactivity control drive mechanism

International Nuclear Information System (INIS)

Zhao Tianyu; Huang Zhiyong; Chen Feng; He Xuedong

2010-01-01

The startup, power regulation and safety shutdown of the nuclear reactor are operated by the reactivity control devices. Reactivity control drive mechanism is a key mechanical transmission component, which directly control the location of the neutron absorber in the core. Its working condition is complex, and its service life should be long., which requires high reliability. PWR as well as newly developed different type of reactors have different control devices drive mechanism. This paper mainly do analysis and comparison about the working environment, mechanical transmission principle, structure, performance, service life and other aspects of PWR, HTR control devices drive mechanism. In addition, this paper is also based on the working principles of reactive control devices drive mechanism, also consider the trends of its design and test verification by the international countries, and discussed the method and feasibility of improving and perfecting the structure and function of drive mechanism. (authors)

Model Predictive Control techniques with application to photovoltaic, DC Microgrid, and a multi-sourced hybrid energy system

Science.gov (United States)

Shadmand, Mohammad Bagher

Renewable energy sources continue to gain popularity. However, two major limitations exist that prevent widespread adoption: availability and variability of the electricity generated and the cost of the equipment. The focus of this dissertation is Model Predictive Control (MPC) for optimal sized photovoltaic (PV), DC Microgrid, and multi-sourced hybrid energy systems. The main considered applications are: maximum power point tracking (MPPT) by MPC, droop predictive control of DC microgrid, MPC of grid-interaction inverter, MPC of a capacitor-less VAR compensator based on matrix converter (MC). This dissertation firstly investigates a multi-objective optimization technique for a hybrid distribution system. The variability of a high-penetration PV scenario is also studied when incorporated into the microgrid concept. Emerging (PV) technologies have enabled the creation of contoured and conformal PV surfaces; the effect of using non-planar PV modules on variability is also analyzed. The proposed predictive control to achieve maximum power point for isolated and grid-tied PV systems speeds up the control loop since it predicts error before the switching signal is applied to the converter. The low conversion efficiency of PV cells means we want to ensure always operating at maximum possible power point to make the system economical. Thus the proposed MPPT technique can capture more energy compared to the conventional MPPT techniques from same amount of installed solar panel. Because of the MPPT requirement, the output voltage of the converter may vary. Therefore a droop control is needed to feed multiple arrays of photovoltaic systems to a DC bus in microgrid community. Development of a droop control technique by means of predictive control is another application of this dissertation. Reactive power, denoted as Volt Ampere Reactive (VAR), has several undesirable consequences on AC power system network such as reduction in power transfer capability and increase in

Development of welding technique by remote control at the JMTR Hot Laboratory

International Nuclear Information System (INIS)

Shimizu, Michio; Iwamatu, Sigemi; Takada, Humiki

2000-03-01

Several kinds of welding techniques have been systematically developed using the remote controlled procedures in the JMTR Hot Laboratory. These are as follows, (1) re-instrumentation's of FP gas pressure gauge and thermocouple to an irradiated fuel rod for the centerline temperature measurement, (2) welding of the un-irradiated/irradiated specimen and machining process to produce tensile test specimens, (3) fabrication of Co-60 radiation source from materials for reactivity adjustment in JMTR core, (4) re-capsuling of irradiated materials in the different types of irradiation facilities. These research and development of circumferential and sealed welding for capsuling and welding of irradiated specimen for re-irradiation were implemented under the remote-controlled conditions in the Hot Cell. These techniques will be very indispensable for supporting the irradiation experiments to be conducted in the JMTR. (author)

Reactivity anomaly surveillance in the Fast Flux Test Facility through cycle 3

International Nuclear Information System (INIS)

Knutson, B.J.; Harris, R.A.

1984-08-01

The technique for monitoring core reactivity during power operation used at the Fast Flux Test Facility (FFTF) is described. This technique relies on comparing predicted to measured rod positions to detect any anomalous (or unpredicted) core reactivity changes. It is implemented on the Plant Data System (PDS) computer and thus provides rapid indication of any abnormal core conditions. The prediction algorithms use thermal-hydraulic, control rod position and neutron flux sensor information to predict the core reactivity state. Initial results of using this technique based mainly on theoretical formulations is presented. The results show that the reactivity changes due to increasing reactor power (power defect) and burnup of the fuel were within approx. 16% of predicted values. To increase the sensitivity and accuracy of this technique, the prediction algorithms were calibrated to actual operating data. The work of calibrating this technique and the results of using the calibrated technique up through the third full operating cycle are summarized

Engine combustion control at low loads via fuel reactivity stratification

Science.gov (United States)

Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

2014-10-07

A compression ignition (diesel) engine uses two or more fuel charges during a combustion cycle, with the fuel charges having two or more reactivities (e.g., different cetane numbers), in order to control the timing and duration of combustion. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot). At low load and no load (idling) conditions, the aforementioned results are attained by restricting airflow to the combustion chamber during the intake stroke (as by throttling the incoming air at or prior to the combustion chamber's intake port) so that the cylinder air pressure is below ambient pressure at the start of the compression stroke.

Engine combustion control at low loads via fuel reactivity stratification

Energy Technology Data Exchange (ETDEWEB)

Reitz, Rolf Deneys; Hanson, Reed M.; Splitter, Derek A.; Kokjohn, Sage

2017-12-26

A compression ignition (diesel) engine uses two or more fuel charges during a combustion cycle, with the fuel charges having two or more reactivities (e.g., different cetane numbers), in order to control the timing and duration of combustion. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot). At low load and no load (idling) conditions, the aforementioned results are attained by restricting airflow to the combustion chamber during the intake stroke (as by throttling the incoming air at or prior to the combustion chamber's intake port) so that the cylinder air pressure is below ambient pressure at the start of the compression stroke.

Realization of PbS thin films by reactive evaporation technique for possible opto-electronic applications

Energy Technology Data Exchange (ETDEWEB)

A, Abhilash, E-mail: abhiltp@cusat.ac.in; Nair, Aparna S.; S, Rajasree; E, Hiba Rahman; Pradeep, B. [Solid State Physics Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi-682022 (India)

2015-06-24

Stoichiometric Lead sulphide (PbS) thin films were successfully prepared on glass substrates by reactive evaporation technique. Elemental evaporation of lead and sulphur taken in different sources onto substrates held at temperature of 400±5K employed in the present study. The structural as well as compositional studies compromises compound formation. Electrical transport properties and optical co-efficient were evaluated from appropriate characterization techniques.

Reactive gas control of non-stable plasma conditions

International Nuclear Information System (INIS)

Bellido-Gonzalez, V.; Daniel, B.; Counsell, J.; Monaghan, D.

2006-01-01

Most industrial plasma processes are dependant upon the control of plasma properties for repeatable and reliable production. The speed of production and range of properties achieved depend on the degree of control. Process control involves all the aspects of the vacuum equipment, substrate preparation, plasma source condition, power supplies, process drift, valves (inputs/outputs), signal and data processing and the user's understanding and ability. In many cases, some of the processes which involve the manufacturing of interesting coating structures, require a precise control of the process in a reactive environment [S.J. Nadel, P. Greene, 'High rate sputtering technology for throughput and quality', International Glass Review, Issue 3, 2001, p. 45. ]. Commonly in these circumstances the plasma is not stable if all the inputs and outputs of the system were to remain constant. The ideal situation is to move a process from set-point A to B in zero time and maintain the monitored signal with a fluctuation equal to zero. In a 'real' process that's not possible but improvements in the time response and energy delivery could be achieved with an appropriate algorithm structure. In this paper an advanced multichannel reactive plasma gas control system is presented. The new controller offers both high-speed gas control combined with a very flexible control structure. The controller uses plasma emission monitoring, target voltage or any process sensor monitoring as the input into a high-speed control algorithm for gas input. The control algorithm and parameters can be tuned to different process requirements in order to optimize response times

Joint excitation and reactive power control in thermal power plant

Directory of Open Access Journals (Sweden)

Dragosavac Jasna

2013-01-01

Full Text Available The coordinated voltage and reactive power controller, designed for the thermal power plant, is presented in the paper. A brief explanation of the need for such device is given and justification for commissioning of such equipment is outlined. After short description of the theoretical background of the proposed control design, the achieved features of the commissioned equipment are fully given. Achieved performances are illustrated by recorded reactive power and bus voltage responses after commissioning of the described equipment into the largest thermal power plant in Serbia. As it can be seen in presented records, all design targets are met.

The effects of trait impulsivity on proactive and reactive interference control.

Science.gov (United States)

Xiang, Ling; Chen, Yan; Chen, Antao; Zhang, Fenghua; Xu, Fuming; Wang, Baoxi

2018-02-01

The current study used event-related brain potentials (ERPs) to explore whether self-reported trait impulsivity in healthy individuals might be differentially related to proactive and reactive interference control. Participants with high and low impulsivity (HI and LI, respectively) performed a modified version of the prime-target interference task. Proactive interference control was induced in the mostly incongruent (MI) context and reactive interference control was induced in the mostly congruent (MC) context. Although the behavioral data revealed no difference between HI and LI individuals in terms of the interference effects (incongruent - congruent) under both contexts, the ERP results showed that impulsivity has a different influence on the interference effects under different task contexts. In the MC context, the interference effects on the medial frontal negativity (MFN) and the negative sustained potential (N-SP) were greater, while that on the positive sustained potential (P-SP) were smaller in the HI compared to those in the LI group. This suggests that high levels of impulsivity might be associated with a reduced efficiency of the processes supporting reactive control to resolve interference when interference is not expected. In contrast, the three ERP indices (MFN, P-SP, and N-SP) of interference processing in the MI context were insensitive to variations in impulsivity. This suggests that HI individuals might be as effective as LI individuals in recruiting proactive control for sustained active maintenance of task goals to anticipate and prevent interference throughout the experimental blocks where interference occurs frequently. In conclusion, these results indicate that impulsivity has a more negative influence on reactive interference control than on proactive interference control. Copyright © 2017. Published by Elsevier B.V.

Comparison of techniques of detecting immunoglobulin-binding protein reactivity to immunoglobulin produced by different avian and mammalian species.

Science.gov (United States)

Justiz-Vaillant, A A; Akpaka, P E; McFarlane-Anderson, N; Smikle, M F

2013-01-01

The rationale of this study was to use several immunological assays to investigate the reactivity of immunoglobulin binding protein (IBP) to immunoglobulins from various avian and mammalian species. The IBP studied were Staphylococcal protein A (SpA), Streptococcal protein G (SpG), Peptostreptococcal protein L (SpL) and recombinant protein LA (SpLA). The various immunological techniques used were double immunodiffusion (Ouchterlony technique) that tested positive high protein reactivities, direct and competitive enzyme-linked immunosorbent assays (ELISAs) that tested moderate and low positive protein binding capacities, respectively. In addition to sandwich ELISAs, immunoblot analyses and Ig-purification by SpA-affinity chromatography, which were sensitive tests and helpful in the screening and confirmatory tests were also used. The Ouchterlony technique showed that compared to the other proteins, SpLA had the highest range of reactivity with animal sera and purified immunoglobulins while SpL was least reactive. With the direct ELISA, SpL reacted with the raccoon sera, rabbit IgG and with IgY from bantam hens and pigeons. While with the direct ELISA, SpA reacted with sera from skunk, coyote, raccoon, mule, donkey and human. The sandwich ELISA revealed high reactivity of both SpG and SpLA with mammalian sera titres ranging from 1:32 (raccoon serum) to 1:1024 (mule and donkey sera). These results suggest that IBP can be used for the detection of immunoglobulin using various immunological assays and this is important for the diagnosis of infectious diseases in animal and bird populations studied and in the purification of immunoglobulins.

Reactive power and voltage control strategy based on dynamic and adaptive segment for DG inverter

Science.gov (United States)

Zhai, Jianwei; Lin, Xiaoming; Zhang, Yongjun

2018-03-01

The inverter of distributed generation (DG) can support reactive power to help solve the problem of out-of-limit voltage in active distribution network (ADN). Therefore, a reactive voltage control strategy based on dynamic and adaptive segment for DG inverter is put forward to actively control voltage in this paper. The proposed strategy adjusts the segmented voltage threshold of Q(U) droop curve dynamically and adaptively according to the voltage of grid-connected point and the power direction of adjacent downstream line. And then the reactive power reference of DG inverter can be got through modified Q(U) control strategy. The reactive power of inverter is controlled to trace the reference value. The proposed control strategy can not only control the local voltage of grid-connected point but also help to maintain voltage within qualified range considering the terminal voltage of distribution feeder and the reactive support for adjacent downstream DG. The scheme using the proposed strategy is compared with the scheme without the reactive support of DG inverter and the scheme using the Q(U) control strategy with constant segmented voltage threshold. The simulation results suggest that the proposed method has a significant improvement on solving the problem of out-of-limit voltage, restraining voltage variation and improving voltage quality.

Power and reactive power simultaneous control by 0.5 MJ superconducting magnet energy storage

International Nuclear Information System (INIS)

Ise, Toshifumi; Tsuji, Kiichiro; Murakami, Yoshishige

1984-01-01

Superconducting magnet energy storage (SMES) is expected to be widely applied to the pulsed sources for fusion reactor research and to the energy storage substituting for pumping-up power stations, because of its fast energy storing and discharging and very high efficiency. Some results have been obtained so far. In this paper, however, the simultaneous control of power and reactive power is considered for an energy storage composed of two sets of thyristorized power conversion system and superconducting magnets in series connection, and a direct digital control system is described on the principle, design and configuration including the compensator, and on the experiment using the 0.5 MJ superconducting magnet energy storage installed in the Superconduction Engineering Experiment Center, Osaka University. The results obtained are as follows: (1) P control priority mode and Q control priority mode (in which power and reactive power control has priority, respectively) were proposed as the countermeasures when the simultaneous control of power and reactive power became impossible; (2) the design method was established, by which power and reactive power control loops can independently be designed as a result of simulation; (3) the achievement of the simultaneous control of power and reactive power was confirmed by using P-control priority mode and Q-control priority mode, in the experiment using the control system designed by simulation. The validity of simulation model was also confirmed by actual response waveforms. (Wakatsuki, Y.)

Hedonic orientation moderates the association between cognitive control and affect reactivity to daily hassles in adolescent boys.

Science.gov (United States)

Klipker, Kathrin; Wrzus, Cornelia; Rauers, Antje; Riediger, Michaela

2017-04-01

People often seek to regulate their affective reactions when confronted with hassles. Hassle reactivity is lower for people with higher cognitive control, presumably because of better affect regulation. Many adolescents, however, show higher hassle reactivity than children, despite better cognitive control. The present study aims to understand whether motivational differences when seeking to regulate affective experiences moderate the association between cognitive control and hassle reactivity in adolescence. We hypothesized that higher cognitive control is related to lower hassle reactivity only for adolescents with a strong hedonic orientation, that is, for adolescents who seek to maintain or enhance positive or to dampen negative affect. We investigated 149 boys' (age range: 10-20 years) hedonic orientation and affect reactivity toward daily hassles during 2 weeks of experience sampling. Higher cognitive control, assessed with a working memory battery in the laboratory, was associated with stronger hassle reactivity in individuals with low hedonic orientation. The more hedonic-oriented individuals were, the lower was their hassle reactivity, but only in combination with high cognitive control. Our findings illustrate that higher cognitive control is not always related to lower hassle reactivity. Rather, when daily hassles compromise affect balance, hedonic orientation is equally important to understand affect reactivity in adolescent boys. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Reactive and Proactive Interference Control in Adults with Autism Spectrum Disorder across the Lifespan

Science.gov (United States)

Lever, Anne G.; Ridderinkhof, K. Richard; Marsman, Maarten; Geurts, Hilde M.

2017-01-01

As a large heterogeneity is observed across studies on interference control in autism spectrum disorder (ASD), research may benefit from the use of a cognitive framework that models specific processes underlying reactive and proactive control of interference. Reactive control refers to the expression and suppression of responses and proactive…

Active and Reactive Power Control Strategy for Grid-Connected Six-Phase Generator by Using Multi-Modular Matrix Converters

Directory of Open Access Journals (Sweden)

David Caballero

2016-12-01

Full Text Available This paper proposes an active and reactive power control strategy based on predictive control approaches applied to gridconnected renewable energy systems. To accomplish this a multi-modular matrix converter topologies are used in combination with a simple but efficient grid synchronization strategy. The theoretical performance analysis is performed considering a six-phase wind energy generator system interconnected with the grid. Results based on a MATLAB/Simulink simulation environment are discussed and the most relevant characteristics of the proposed control technique are highlighted considering the total harmonic distortion and the mean squared error as a parameters of performance.

Influence of control and physical effort on cardiovascular reactivity to a video game task.

Science.gov (United States)

Weinstein, Suzanne E; Quigley, Karen S; Mordkoff, J Toby

2002-09-01

This study investigated the influences of both perceived control and physical effort on cardiovascular reactivity. Undergraduates (N = 32) played a video game task interrupted by aversive noise. Perceived control of the noise was manipulated by instructions indicating the presence or absence of a contingency between performance and noise presentations. Physical effort was manipulated by controlling the physical force required to perform the task. There was a significant main effect of control on systolic blood pressure (SBP) and total peripheral resistance (TPR), with both increasing more during low than high control conditions. The results suggest that high perceived control over aversive noise in an effortful task reduces SBP and TPR reactivity relative to low perceived control. The results are consistent with the idea that control buffers the reactivity associated with task performance under aversive conditions.

An Improved Droop Control Strategy for Reactive Power Sharing in Islanded Microgrid

DEFF Research Database (Denmark)

Han, Hua; Liu, Yao; Sun, Yao

2015-01-01

For microgrid in islanded operation, due to the effects of mismatched line impedance, the reactive power could not be shared accurately with the conventional droop method. To improve the reactive power sharing accuracy, this paper proposes an improved droop control method. The proposed method...... in output voltage amplitude. Therefore, the voltage recovery operation is proposed to compensate the decrease. The needed communication in this method is very simple, and the plug-and-play is reserved. Simulations and experimental results show that the improved droop controller can share load active...... and reactive power, improve the power quality of the microgrid, and also have a good dynamic performance....

Reactivity anomalies in the FFTF [Fast Flux Test Facility

International Nuclear Information System (INIS)

Knutson, B.J.; Harris, R.A.

1987-04-01

Experience using an automated core reactivity monitoring technique at the Fast Flux Test Facility (FFTF) through eight operating cycles is described. This technique relies on comparing predicted to measured rod positions to detect any anomalous (or unpredicted) core reactivity changes. Reactivity worth predictions of core state changes (e.g., temperature and irradiation changes) and compensating control rod movements are required for the rod position comparison. A substantial data base now exists to evaluate changes in temperature reactivity feedback effects operational in the FFTF, rod worth changes due to core loading, temperature and irradiation effects and burnup effects associated with transmutation of fuel materials. This report summarizes preliminary work of correlating zero power and at-power rod worth measurement data, calculated burnup rates and rod worths using the latest ENDF/B-V cross section set for each cycle to evaluate the prediction models and attempt to resolve observed reactivity anomalies. 2 figs., 2 tabs

Controller Design of DFIG Based Wind Turbine by Using Evolutionary Soft Computational Techniques

Directory of Open Access Journals (Sweden)

O. P. Bharti

2017-06-01

Full Text Available This manuscript illustrates the controller design for a doubly fed induction generator based variable speed wind turbine by using a bioinspired scheme. This methodology is based on exploiting two proficient swarm intelligence based evolutionary soft computational procedures. The particle swarm optimization (PSO and bacterial foraging optimization (BFO techniques are employed to design the controller intended for small damping plant of the DFIG. Wind energy overview and DFIG operating principle along with the equivalent circuit model is adequately discussed in this paper. The controller design for DFIG based WECS using PSO and BFO are described comparatively in detail. The responses of the DFIG system regarding terminal voltage, current, active-reactive power, and DC-Link voltage have slightly improved with the evolutionary soft computational procedure. Lastly, the obtained output is equated with a standard technique for performance improvement of DFIG based wind energy conversion system.

Optimization Based Shunt APF Controller to Mitigate Reactive Power, Burden of Neutral Conductor, Current Harmonics and Improve cosɸ

Directory of Open Access Journals (Sweden)

P. Anjana

2017-03-01

Full Text Available This paper presents a Modified Gravitational Search Algorithm (MGSA to improve the performance of PI controller in varying load condition. The proposed approach is capable of mitigating reactive power, neutral current, source current THD and significant improvement in power factor nearly unity (0.997. The DC link voltage across the capacitor is controlled by PI controller which is deciding the performance of shunt APF. Hence, the robust optimization technique based integral time square error (ITSE with consideration of weight factor (α & β, maximum overshoot ((|(∆_Ve ̅〖(n〗_max | and setling time t_s-t_0, is providing the optimum solution of Kp & Ki. The robustness of proposed objective function and algorithm compared with GSA based three other error criterion techniques. The efficiency of the proposed controller has been tested over nonlinear and unbalance loading condition. The performance of ITSE based MGSA-PI controller is batter then other three error criterion techniques. The values of THD are below the mark of 5% specified in IEEE-519 standard.

An iterative method for controlling reactive power flow in boundary transformers

Energy Technology Data Exchange (ETDEWEB)

Trigo, Angel L.; Martinez, Jose L.; Riquelme, Jesus; Romero, Esther [Department of Electrical Engineering, University of Seville (Spain)

2011-02-15

This paper presents an operational tool designed to help the system operator to control the reactive power flow in transmission-subtransmission boundary transformers. The main objective is to determine the minimum number of control actions necessary to ensure that reactive power flows in transmission/subtransmission transformers remain within limits. The proposed iterative procedure combines the use of a linear programming problem and a load flow tool. The linear programming assumes a linear behaviour between dependent and control variables around an operating point, modelled with sensitivities. Experimental results regarding IEEE systems are provided comparing the performance of the proposed approach with that of a conventional optimal power flow. (author)

Control technique for enhancing the stable operation of distributed generation units within a microgrid

International Nuclear Information System (INIS)

Mehrasa, Majid; Pouresmaeil, Edris; Mehrjerdi, Hasan; Jørgensen, Bo Nørregaard; Catalão, João P.S.

2015-01-01

Highlights: • A control technique for enhancing the stable operation of distributed generation units is proposed. • Passivity-based control technique is considered to analyze the dynamic and steady-state behaviors. • The compensation of instantaneous variations in the reference current components is considered. • Simulation results confirm the performance of the control scheme within the microgrid. - Abstract: This paper describes a control technique for enhancing the stable operation of distributed generation (DG) units based on renewable energy sources, during islanding and grid-connected modes. The Passivity-based control technique is considered to analyze the dynamic and steady-state behaviors of DG units during integration and power sharing with loads and/or power grid, which is an appropriate tool to analyze and define a stable operating condition for DG units in microgrid technology. The compensation of instantaneous variations in the reference current components of DG units in ac-side, and dc-link voltage variations in dc-side of interfaced converters, are considered properly in the control loop of DG units, which is the main contribution and novelty of this control technique over other control strategies. By using the proposed control technique, DG units can provide the continuous injection of active power from DG sources to the local loads and/or utility grid. Moreover, by setting appropriate reference current components in the control loop of DG units, reactive power and harmonic current components of loads can be supplied during the islanding and grid-connected modes with a fast dynamic response. Simulation results confirm the performance of the control scheme within the microgrid during dynamic and steady-state operating conditions

Contamination Control Techniques

Energy Technology Data Exchange (ETDEWEB)

EBY, J.L.

2000-05-16

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics.

Contamination Control Techniques

International Nuclear Information System (INIS)

EBY, J.L.

2000-01-01

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics

A technique for computing bowing reactivity feedback in LMFBR's

International Nuclear Information System (INIS)

Finck, P.J.

1987-01-01

During normal or accidental transients occurring in a LMFBR core, the assemblies and their support structure are subjected to important thermal gradients which induce differential thermal expansions of the walls of the hexcans and differential displacement of the assembly support structure. These displacements, combined with the creep and swelling of structural materials, remain quite small, but the resulting reactivity changes constitute a significant component of the reactivity feedback coefficients used in safety analyses. It would be prohibitive to compute the reactivity changes due to all transients. Thus, the usual practice is to generate reactivity gradient tables. The purpose of the work presented here is twofold: develop and validate an efficient and accurate scheme for computing these reactivity tables; and to qualify this scheme

Multivariable model predictive control design of reactive distillation column for Dimethyl Ether production

Science.gov (United States)

Wahid, A.; Putra, I. G. E. P.

2018-03-01

Dimethyl ether (DME) as an alternative clean energy has attracted a growing attention in the recent years. DME production via reactive distillation has potential for capital cost and energy requirement savings. However, combination of reaction and distillation on a single column makes reactive distillation process a very complex multivariable system with high non-linearity of process and strong interaction between process variables. This study investigates a multivariable model predictive control (MPC) based on two-point temperature control strategy for the DME reactive distillation column to maintain the purities of both product streams. The process model is estimated by a first order plus dead time model. The DME and water purity is maintained by controlling a stage temperature in rectifying and stripping section, respectively. The result shows that the model predictive controller performed faster responses compared to conventional PI controller that are showed by the smaller ISE values. In addition, the MPC controller is able to handle the loop interactions well.

Distributed Reactive Power Control based Conservation Voltage Reduction in Active Distribution Systems

Directory of Open Access Journals (Sweden)

EMIROGLU, S.

2017-11-01

Full Text Available This paper proposes a distributed reactive power control based approach to deploy Volt/VAr optimization (VVO / Conservation Voltage Reduction (CVR algorithm in a distribution network with distributed generations (DG units and distribution static synchronous compensators (D-STATCOM. A three-phase VVO/CVR problem is formulated and the reactive power references of D-STATCOMs and DGs are determined in a distributed way by decomposing the VVO/CVR problem into voltage and reactive power control. The main purpose is to determine the coordination between voltage regulator (VR and reactive power sources (Capacitors, D-STATCOMs and DGs based on VVO/CVR. The study shows that the reactive power injection capability of DG units may play an important role in VVO/CVR. In addition, it is shown that the coordination of VR and reactive power sources does not only save more energy and power but also reduces the power losses. Moreover, the proposed VVO/CVR algorithm reduces the computational burden and finds fast solutions. To illustrate the effectiveness of the proposed method, the VVO/CVR is performed on the IEEE 13-node test system feeder considering unbalanced loading and line configurations. The tests are performed taking the practical voltage-dependent load modeling and different customer types into consideration to improve accuracy.

Reactivity control system of the high temperature engineering test reactor

International Nuclear Information System (INIS)

Tachibana, Yukio; Sawahata, Hiroaki; Iyoku, Tatsuo; Nakazawa, Toshio

2004-01-01

The reactivity control system of the high temperature engineering test reactor (HTTR) consists of a control rod system and a reserve shutdown system. During normal operation, reactivity is controlled by the control rod system, which consists of 32 control rods (16 pairs) and 16 control rod drive mechanisms except for the case when the center control rods are removed to perform an irradiation test. In an unlikely event that the control rods fail to be inserted, reserve shutdown system is provided to insert pellets of neutron-absorbing material into the core. Alloy 800H is chosen for the metallic parts of the control rods. Because the maximum temperature of the control rods reaches about 900 deg. C at reactor scrams, structural design guideline and design material data on Alloy 800H are needed for the high temperature design. The design guideline for the HTTR control rod is based on ASME Code Case N-47-21. Design material data is also determined and shown in this paper. Observing the guideline, temperature and stress analysis were conducted; it can be confirmed that the target life of the control rods of 5 years can be achieved. Various tests conducted for the control rod system and the reserve shutdown system are also described

Study on chemical reactivity control of liquid sodium. Research program

International Nuclear Information System (INIS)

Saito, Jun-ichi; Ara, Kuniaki; Sugiyama, Ken-ichiro; Kitagawa, Hiroshi; Oka, Nobuki; Yoshioka, Naoki

2007-01-01

Liquid sodium has the excellent properties as coolant of the fast breeder reactor (FBR). On the other hand, it reacts high with water and oxygen. So an innovative technology to suppress the reactivity is desired. The purpose of this study is to control the chemical reactivity of liquid sodium by dispersing the nanometer-size metallic particles (we call them Nano-particles) into liquid sodium. We focus on the atomic interaction between Nano-particles and sodium atoms. And we try to apply it to suppress the chemical reactivity of liquid sodium. Liquid sodium dispersing Nano-particles is named 'Nano-fluid'. Research programs of this study are the Nano-particles production, the evaluation of reactivity suppression of liquid sodium and the feasibility study to FBR plant. In this paper, the research programs and status are described. The important factors for particle production were understood. In order to evaluate the chemical reactivity of Nano-fluid the research programs were planned. The feasibility of the application of Nano-fluid to the coolant of FBR plant was evaluated preliminarily from the viewpoint of design and operation. (author)

Active and reactive power control of a current-source PWM-rectifier using space vectors

Energy Technology Data Exchange (ETDEWEB)

Salo, M.; Tuusa, H. [Tampere University of Technology (Finland). Department of Electrical Engineering, Power Electronics

1997-12-31

In this paper the current-source PWM-rectifier with active and reactive power control is presented. The control system is realized using space vector methods. Also, compensation of the reactive power drawn by the line filter is discussed. Some simulation results are shown. (orig.) 8 refs.

Mechanisms and neuronal networks involved in reactive and proactive cognitive control of interference in working memory.

Science.gov (United States)

Irlbacher, Kerstin; Kraft, Antje; Kehrer, Stefanie; Brandt, Stephan A

2014-10-01

Cognitive control can be reactive or proactive in nature. Reactive control mechanisms, which support the resolution of interference, start after its onset. Conversely, proactive control involves the anticipation and prevention of interference prior to its occurrence. The interrelation of both types of cognitive control is currently under debate: Are they mediated by different neuronal networks? Or are there neuronal structures that have the potential to act in a proactive as well as in a reactive manner? This review illustrates the way in which integrating knowledge gathered from behavioral studies, functional imaging, and human electroencephalography proves useful in answering these questions. We focus on studies that investigate interference resolution at the level of working memory representations. In summary, different mechanisms are instrumental in supporting reactive and proactive control. Distinct neuronal networks are involved, though some brain regions, especially pre-SMA, possess functions that are relevant to both control modes. Therefore, activation of these brain areas could be observed in reactive, as well as proactive control, but at different times during information processing. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of various welding techniques for refractory and reactive metals and alloys

International Nuclear Information System (INIS)

Tonpe, Sunil; Saibaba, N.

2016-01-01

Nuclear Fuel Complex (NFC), Hyderabad, India with its excellent manufacturing facilities, produces nuclear fuel and structural components for nuclear reactors. NFC has taken up the challenging job of production of various critical components made out of refractory and reactive metals and alloys for nuclear and aerospace applications as an indigenization import substitute program. Refractory metals are prime candidates for many high temperature aerospace components because of refractory metal's high melting points and inherent creep resistance. The use of refractory metals is often limited because of their poor room temperature properties, inadequate oxidation resistance at elevated temperatures, difficulties associated with joining or welding etc. These advanced materials demand stringent requirement with respect to chemistry, dimensional tolerances, mechanical and metallurgical properties. This paper discusses in detail various welding techniques adopted in NFC for refractory and reactive metals and alloys such as Nb, Zr, Ti, Ta, Zircaloy, Titanium-half alloy etc. to manufacture various components and assemblies required for nuclear and aerospace applications

Neural mechanisms of proactive and reactive cognitive control in social anxiety.

Science.gov (United States)

Schmid, Petra C; Kleiman, Tali; Amodio, David M

2015-09-01

Social anxiety--the fear of social embarrassment and negative evaluation by others--ranks among people's worst fears, and it is often thought to impair task performance. We investigated the neurocognitive processes through which trait social anxiety relates to task performance, proposing a model of the joint contributions of reactive control, theoretically associated with conflict monitoring and activity of the dorsal anterior cingulate cortex (dACC), and proactive control, theoretically associated with top-down regulation and activity of the dorsolateral prefrontal cortex (dlPFC). Participants varying in their degree of trait social anxiety completed the Eriksen flanker task while electroencephalography (EEG) was recorded. Task-related left dlPFC activity was indexed by relative left prefrontal EEG (inverse alpha), and conflict-related dACC activity was indexed by the N2r component of the event-related potential. Stronger activity in both regions predicted better response control, and greater social anxiety was associated with worse response control. Furthermore, for all participants, greater left prefrontal EEG activity predicted better behavioral control, but for high social anxiety participants only, greater N2r responses also predicted behavioral control. This pattern suggests that low social anxiety individuals engaged a proactive control process, driven by dlPFC activity, whereas high social anxiety individuals relied additionally on a reactive control process, driven by conflict-related dACC activity. These findings support a model of control that involves different patterns of interplay between proactive and reactive strategies and may help to explain self-regulatory impairments in social anxiety. Copyright © 2015 Elsevier Ltd. All rights reserved.

Control Rod Reactivity Measurements in the Aagesta Reactor with the Pulsed Neutron Method

Energy Technology Data Exchange (ETDEWEB)

Bjoereus, K

1969-07-01

An extensive series of control rod measurements was made in the Aagesta reactor during the low power experimental period following the first criticality. This report describes the part of these investigations made with the pulsed neutron method, comprising nearly 300 measurements. The main objective was the determination of control rod reactivity worths for different rods and groups of rods, but some supplementary measurements were also made, e.g. a determination of the prompt neutron decay constant for the delayed critical condition and four different cores. The cores consisted of 20, 32, 68, and 140 fuel elements respectively, and measurements were made at room temperature and with the moderator level close to critical for each core, and for the 140-element core also with full moderator height and at the temperatures 140 deg C and 215 deg C. Both fully and partly inserted control rod groups were investigated. The measurements at critical water level give directly the control rod reactivity worths, whereas those with full water height give the shut-down reactivity. A comparison was made between measured reactivity worths for a number of rod groups and those calculated with the HETERO code. The prompt neutron decay constant at delayed criticality {alpha}{sub 0}={beta}/l, for the full core at 215 deg C was found to be 9.60 {+-} 0.30/sec, corresponding to l = 0.76 {+-} 0.02 msec. The shut-down reactivity with 16 coarse control rods in pos. A-D 22, 40-04, 44, 26 is -5% at 25 deg C and -13% at 215 deg C. The relative error is usually around 8% in the reactivity worths, originating mainly from the higher harmonics content in the measured curves.

Reactivity control of nuclear power reactors: new options

International Nuclear Information System (INIS)

Alcala, F.

1984-01-01

Some actual aspects (referring to economy, non-proliferation and environmental impact) of nuclear power reactors has been analyzed from the point of view of the reactivity control physics. Specially studied have been the physical mechanisms related with the spectral shift control method and their general positive effects on those aspects. The analysis carried out suggested the application of the above method of control to reactors with non-hydrogenous fuel cells, which are mainly characterized by their high moderator/fuel ratio. Finally three different types of such fuel cells are presented and some results about one of them (belonging to a PHWR controlled by graphite rods) are given. (author)

Implementing Motivational Features in Reactive Blended Learning: Application to an Introductory Control Engineering Course

Science.gov (United States)

Mendez, J. A.; Gonzalez, E. J.

2011-01-01

This paper presents a significant advance in a reactive blended learning methodology applied to an introductory control engineering course. This proposal was based on the inclusion of a reactive element (a fuzzy-logic-based controller) designed to regulate the workload for each student according to his/her activity and performance. The…

Effect of drop jump technique on the reactive strength index.

Science.gov (United States)

Struzik, Artur; Juras, Grzegorz; Pietraszewski, Bogdan; Rokita, Andrzej

2016-09-01

The basic drill of plyometric training aimed at improving lower limb power and jump height is a drop jump. This exercise can be performed using different techniques, which substantially affects jump variables. Therefore, the aim of this study was to compare the values of the reactive strength index (RSI) for countermovement drop jumps (CDJs) and bounce drop jumps (BDJs). The study was carried out in a group of 8 male youth basketball players. The tests were conducted using the AMTI BP600900 force plate to measure ground reaction forces and the Noraxon MyoMotion system to record kinematic data. Each player performed two CDJs and two BDJs from the height of 15, 30, 45 and 60 cm. The RSI was calculated as a ratio of jump height and contact time. Moreover, the RSI was determined for the amortization and take-off phases separately. Significant differences (p jumps from 30, 45 and 60 cm. Differences in RSI values for jumps from 15 cm were not significant. Furthermore, CDJ height values were significantly higher (p jump technique that is commonly performed by basketball players.

Control Rod Driveline Reactivity Feedback Model for Liquid Metal Reactors

International Nuclear Information System (INIS)

Kwon, Young-Min; Jeong, Hae-Yong; Chang, Won-Pyo; Cho, Chung-Ho; Lee, Yong-Bum

2008-01-01

The thermal expansion of the control rod drivelines (CRDL) is one important passive mitigator under all unprotected accident conditions in the metal and oxide cores. When the CRDL are washed by hot sodium in the coolant outlet plenum, the CRDL thermally expands and causes the control rods to be inserted further down into the active core region, providing a negative reactivity feedback. Since the control rods are attached to the top of the vessel head and the core attaches to the bottom of the reactor vessel (RV), the expansion of the vessel wall as it heats will either lower the core or raise the control rods supports. This contrary thermal expansion of the reactor vessel wall pulls the control rods out of the core somewhat, providing a positive reactivity feedback. However this is not a safety factor early in a transient because its time constant is relatively large. The total elongated length is calculated by subtracting the vessel expansion from the CRDL expansion to determine the net control rod expansion into the core. The system-wide safety analysis code SSC-K includes the CRDL/RV reactivity feedback model in which control rod and vessel expansions are calculated using single-nod temperatures for the vessel and CRDL masses. The KALIMER design has the upper internal structures (UIS) in which the CRDLs are positioned outside the structure where they are exposed to the mixed sodium temperature exiting the core. A new method to determine the CRDL expansion is suggested. Two dimensional hot pool thermal hydraulic model (HP2D) originally developed for the analysis of the stratification phenomena in the hot pool is utilized for a detailed heat transfer between the CRDL mass and the hot pool coolant. However, the reactor vessel wall temperature is still calculated by a simple lumped model

Active vibration control by robust control techniques

International Nuclear Information System (INIS)

Lohar, F.A.

2001-01-01

This paper studies active vibration control of multi-degree-of-freedom system. The control techniques considered are LTR, H/sup 2/ and H/sup infinite/. The results show that LTR controls the vibration but its respective settling time is higher than that of the other techniques. The control performance of H/sup infinite/ control is similar to that of H/sup 2/ control in the case of it weighting functions. However, H/sup infinite/ control is superior to H/sup 2/ control with respect to robustness, steady state error and settling time. (author)

A Reactive Blended Learning Proposal for an Introductory Control Engineering Course

Science.gov (United States)

Mendez, Juan A.; Gonzalez, Evelio J.

2010-01-01

As it happens in other fields of engineering, blended learning is widely used to teach process control topics. In this paper, the inclusion of a reactive element--a Fuzzy Logic based controller--is proposed for a blended learning approach in an introductory control engineering course. This controller has been designed in order to regulate the…

Skin Conductance Level Reactivity Moderates the Association Between Parental Psychological Control and Relational Aggression in Emerging Adulthood.

Science.gov (United States)

Wagner, Caitlin R; Abaied, Jamie L

2016-04-01

When studying factors that may heighten risk for relational aggression in youth, it is important to consider characteristics of both the individual and their environment. This research examined the associations between parental psychological control and reactive and proactive relational aggression in emerging adults in college. Given that sympathetic nervous system (SNS) activation may underlie differences between reactive and proactive aggression and has been shown to moderate the effects of parenting on youth development, the moderating role of SNS reactivity [indexed by skin conductance level reactivity (SCLR)] was also examined. Emerging adults (N = 180; 77.2 % female) self-reported on perceptions of parental psychological control and reactive and proactive relational aggression. SCLR was assessed in response to an interpersonal laboratory challenge task. Parental psychological control was positively associated with reactive relational aggression only for emerging adults who exhibited high SCLR. Parental psychological control was positively associated with proactive relational aggression only among emerging adults who showed low SCLR. This study extends previous research on parenting and aggression and suggests that parental psychological control is differentially associated with reactive versus proactive relational aggression, depending on emerging adults' SCLR to interpersonal stress.

From conservative to reactive transport under diffusion-controlled conditions

Science.gov (United States)

Babey, Tristan; de Dreuzy, Jean-Raynald; Ginn, Timothy R.

2016-05-01

We assess the possibility to use conservative transport information, such as that contained in transit time distributions, breakthrough curves and tracer tests, to predict nonlinear fluid-rock interactions in fracture/matrix or mobile/immobile conditions. Reference simulated data are given by conservative and reactive transport simulations in several diffusive porosity structures differing by their topological organization. Reactions includes nonlinear kinetically controlled dissolution and desorption. Effective Multi-Rate Mass Transfer models (MRMT) are calibrated solely on conservative transport information without pore topology information and provide concentration distributions on which effective reaction rates are estimated. Reference simulated reaction rates and effective reaction rates evaluated by MRMT are compared, as well as characteristic desorption and dissolution times. Although not exactly equal, these indicators remain very close whatever the porous structure, differing at most by 0.6% and 10% for desorption and dissolution. At early times, this close agreement arises from the fine characterization of the diffusive porosity close to the mobile zone that controls fast mobile-diffusive exchanges. At intermediate to late times, concentration gradients are strongly reduced by diffusion, and reactivity can be captured by a very limited number of rates. We conclude that effective models calibrated solely on conservative transport information like MRMT can accurately estimate monocomponent kinetically controlled nonlinear fluid-rock interactions. Their relevance might extend to more advanced biogeochemical reactions because of the good characterization of conservative concentration distributions, even by parsimonious models (e.g., MRMT with 3-5 rates). We propose a methodology to estimate reactive transport from conservative transport in mobile-immobile conditions.

Review of Active and Reactive Power Sharing Strategies in Hierarchical Controlled Microgrids

DEFF Research Database (Denmark)

Han, Yang; Li, Hong; Shen, Pan

2017-01-01

Microgrids consist of multiple parallel-connected distributed generation (DG) units with coordinated control strategies, which are able to operate in both grid-connected and islanded mode. Microgrids are attracting more and more attention since they can alleviate the stress of main transmission...... systems, reduce feeder losses, and improve system power quality. When the islanded microgrids are concerned, it is important to maintain system stability and achieve load power sharing among the multiple parallel-connected DG units. However, the poor active and reactive power sharing problems due...... in this paper for active power sharing. Moreover, nonlinear and unbalanced loads could further affect the reactive power sharing when regulating the active power, and it is difficult to share the reactive power accurately only by using the enhanced virtual impedance method. Therefore, the hierarchical control...

Reactive power management and voltage control in deregulated power markets

Science.gov (United States)

Spangler, Robert G.

The research that is the subject of this dissertation is about the management of reactive power and voltage support in the wholesale open access power markets in the United States (US). The purpose of this research is to place decisions about open access market structures, as they relate to reactive power and voltage control, on a logical and consistent economic basis, given the engineering needs of a commercial electric power system. An examination of the electricity markets operating in the US today reveals that current approaches to reactive power management and voltage support are extensions of those based on historical, regulated monopoly electric service. A case for change is built by first looking at the subject of reactive power from an engineering viewpoint and then from an economic perspective. Ultimately, a set of market rules for managing reactive power and voltage support is proposed. The proposal suggests that cost recovery for static and dynamic VARs is appropriately accomplished through the regulated transmission cost of service. Static VAR cost recovery should follow traditional rate recovery methodologies. In the case of dynamic VARs, this work provides a methodology based on the microeconomic theory of the firm for determining such cost. It further suggests that an operational strategy that reduces and limits the use of dynamic VARs, during normal operations, is appropriate. This latter point leads to an increase in the fixed cost of the transmission network but prevents price spikes and short supply situations from affecting, or being affected by, the reactive capability limitations associated with dynamic VARs supplied from synchronous generators. The rules are consistent with a market structure that includes competitive generation and their application will result in the communication of a clear understanding of the responsibilities, related to voltage control, of each type of market entity. In this sense, their application will contribute to

Determination of the most reactivity control rod by pseudo-harmonics perturbation method

International Nuclear Information System (INIS)

Freire, Fernando S.; Silva, Fernando C.; Martinez, Aquilino S.

2005-01-01

Frequently it is necessary to compute the change in core multiplication caused by a change in the core temperature or composition. Even when this perturbation is localized, such as a control rod inserted into the core, one does not have to repeat the original criticality calculation, but instead we can use the well-known pseudo-harmonics perturbation method to express the corresponding change in the multiplication factor in terms of the neutron flux expanded in the basis vectors characterizing the unperturbed core. Therefore we may compute the control rod worth to find the most reactivity control rod to calculate the fast shutdown margin. In this thesis we propose a simple and precise method to identify the most reactivity control rod. (author)

Reactivity margins in heavy water moderated production reactors

International Nuclear Information System (INIS)

Benton, F.D.

1981-11-01

The design of the reactor core and components of the heavy water moderated reactors at the Savannah River Plant (SFP) can be varied to produce a number of isotopes. For the past decade, the predominant reactor core design has been the enriched-depleted lattice. In this lattice, fuel assemblies of highly enriched uranium and target assemblies of depleted uranium, which produce plutonium, occupy alternate lattice positions. This heterogeneous lattice arrangement and a nonuniform control rod distribution result in a reactor core that requires sophisticated calculational methods for accurate reactivity margin and power distribution predictions. For maximum accuracy, techniques must exist to provide a base of observed data for the calculations. Frequent enriched-depleted lattice design changes are required as product demands vary. These changes provided incentive for the development of techniques to combine the results of calculations and observed reactivity data to accurately and conveniently monitor reactivity margins during operation

Fuzzy-TLBO optimal reactive power control variables planning for energy loss minimization

International Nuclear Information System (INIS)

Moghadam, Ahmad; Seifi, Ali Reza

2014-01-01

Highlights: • A new approach to the problem of optimal reactive power control variables planning is proposed. • The energy loss minimization problem has been formulated by modeling the load of system as a Load Duration Curve. • To solving the energy loss problem, the classic methods and the evolutionary methods are used. • A new proposed fuzzy teaching–learning based algorithm is applied to energy loss problem. • Simulations are done to show the effectiveness and superiority of the proposed algorithm compared with other methods. - Abstract: This paper offers a new approach to the problem of optimal reactive power control variables planning (ORPVCP). The basic idea is division of Load Duration Curve (LDC) into several time intervals with constant active power demand in each interval and then solving the energy loss minimization (ELM) problem to obtain an optimal initial set of control variables of the system so that is valid for all time intervals and can be used as an initial operating condition of the system. In this paper, the ELM problem has been solved by the linear programming (LP) and fuzzy linear programming (Fuzzy-LP) and evolutionary algorithms i.e. MHBMO and TLBO and the results are compared with the proposed Fuzzy-TLBO method. In the proposed method both objective function and constraints are evaluated by membership functions. The inequality constraints are embedded into the fitness function by the membership function of the fuzzy decision and the problem is modeled by fuzzy set theory. The proposed Fuzzy-TLBO method is performed on the IEEE 30 bus test system by considering two different LDC; and it is shown that using this method has further minimized objective function than original TLBO and other optimization techniques and confirms its potential to solve the ORPCVP problem with considering ELM as the objective function

Local Reactive Power Control Methods for Overvoltage Prevention of Distributed Solar Inverters in Low-Voltage Grids

DEFF Research Database (Denmark)

Demirok, Erhan; Gonzalez, Pablo Casado; Frederiksen, Kenn H. B.

2011-01-01

on sensitivity analysis. The sensitivity analysis shows that the same amount of reactive power becomes more effective for grid voltage support if the solar inverter is located at the end of a feeder. Based on this fundamental knowledge, a location-dependent power factor set value can be assigned to each inverter......voltage (LV) grids by means of solar inverters with reactive power control capability. This paper underlines weak points of standard reactive power strategies which are already imposed by certain grid codes, and then, the study introduces a new reactive power control method that is based......, and the grid voltage support can be achieved with less total reactive power consumption. In order to prevent unnecessary reactive power absorption from the grid during admissible voltage range or to increase reactive power contribution from the inverters that are closest to the transformer during grid...

Monadic Functional Reactive Programming

NARCIS (Netherlands)

A.J. van der Ploeg (Atze); C Shan

2013-01-01

htmlabstractFunctional Reactive Programming (FRP) is a way to program reactive systems in functional style, eliminating many of the problems that arise from imperative techniques. In this paper, we present an alternative FRP formulation that is based on the notion of a reactive computation: a

Study on evaluating the reactivity worth of the control rods of the PWR 900 MWe

International Nuclear Information System (INIS)

Phan Quoc Vuong; Tran Vinh Thanh; Tran Viet Phu

2015-01-01

Control rods of a nuclear reactor are divided into two groups: shut down and power control. Reactivity worth of the control rods depends nonlinearly on the rods' compositions and positions where the rods are inserted into the core. Therefore, calculation of control rod worth is of high important. In this study, we calculated the reactivity worth of the power control rod bank of the Mitsubishi PWR 900 MWe. The results are integral and differential worth calibration of the control rods. (author)

Approaches for quantifying reactive and low-volatility biogenic organic compound emissions by vegetation enclosure techniques - part A.

Science.gov (United States)

Ortega, John; Helmig, Detlev

2008-06-01

The high reactivity and low vapor pressure of many biogenic volatile organic compounds (BVOC) make it difficult to measure whole-canopy fluxes of BVOC species using common analytical techniques. The most appropriate approach for estimating these BVOC fluxes is to determine emission rates from dynamic vegetation enclosure measurements. After scaling leaf- and branch-level emission rates to the canopy level, these fluxes can then be used in models to determine BVOC influences on atmospheric chemistry and aerosol processes. Previously published reports from enclosure measurements show considerable variation among procedures with limited guidelines or standard protocols to follow. This article reviews this literature and describes the variety of enclosure types, materials, and analysis techniques that have been used to determine BVOC emission rates. The current review article is followed by a companion paper which details a comprehensive enclosure technique that incorporates both recommendations from the literature as well as insight gained from theoretical calculations and practical experiences. These methods have yielded new BVOC emission data for highly reactive monoterpenes (MT) and sesquiterpenes (SQT) from a variety of vegetation species.

Derivation and experimental demonstration of the perturbed reactivity method for the determination of subcriticality

International Nuclear Information System (INIS)

Kwok, K.S.; Bernard, J.A.; Lanning, D.D.

1992-01-01

The perturbed reactivity method is a general technique for the estimation of reactivity. It is particularly suited to the determination of a reactor's initial degree of subcriticality and was developed to facilitate the automated startup of both spacecraft and multi-modular reactors using model-based control laws. It entails perturbing a shutdown reactor by the insertion of reactivity at a known rate and then estimating the initial degree of subcriticality from observation of the resulting reactor period. While similar to inverse kinetics, the perturbed reactivity method differs in that the net reactivity present in the core is treated as two separate entities. The first is that associated with the known perturbation. This quantity, together with the observed period and the reactor's describing parameters, are the inputs to the method's implementing algorithm. The second entity, which is the algorithm;s output, is the sum of all other reactivities including those resulting from inherent feedback and the initial degree of subcriticality. During an automated startup, feedback effects will be minimal. Hence, when applied to a shutdown reactor, the output of the perturbed reactivity method will be a constant that is equal to the initial degree of subcriticality. This is a major advantage because repeated estimates can be made of this one quantity and signal smoothing techniques can be applied to enhance accuracy. In addition to describing the theoretical basis for the perturbed reactivity method, factors involved in its implementation such as the movement of control devices other than those used to create the perturbation, source estimation, and techniques for data smoothing are presented

Electrical engineering unit for the reactive power control of the load bus at the voltage instability

Science.gov (United States)

Kotenev, A. V.; Kotenev, V. I.; Kochetkov, V. V.; Elkin, D. A.

2018-01-01

For the purpose of reactive power control error reduction and decrease of the voltage sags in the electric power system caused by the asynchronous motors started the mathematical model of the load bus was developed. The model was built up of the sub-models of the following elements: a transformer, a transmission line, a synchronous and an asynchronous loads and a capacitor bank load, and represents the automatic reactive power control system taking into account electromagnetic processes of the asynchronous motors started and reactive power changing of the electric power system elements caused by the voltage fluctuation. The active power/time and reactive power/time characteristics based on the recommended procedure of the equivalent electric circuit parameters calculation were obtained. The derived automatic reactive power control system was shown to eliminate the voltage sags in the electric power system caused by the asynchronous motors started.

Digital reactivity meter

International Nuclear Information System (INIS)

Akkus, B.; Anac, H.; Alsan, S.; Erk, S.

1991-01-01

Nowadays, various digital methods making use of microcomputers for neutron detector signals and determining the reactivity by numerical calculations are used in reactor control systems in place of classical reactivity meters. In this work, a calculation based on the ''The Time Dependent Transport Equation'' has been developed for determining the reactivity numerically. The reactivity values have been obtained utilizing a computer-based data acquisition and control system and compared with the analog reactivity meter values as well as the values calculated from the ''Inhour Equation''

Statistical Techniques for Project Control

CERN Document Server

Badiru, Adedeji B

2012-01-01

A project can be simple or complex. In each case, proven project management processes must be followed. In all cases of project management implementation, control must be exercised in order to assure that project objectives are achieved. Statistical Techniques for Project Control seamlessly integrates qualitative and quantitative tools and techniques for project control. It fills the void that exists in the application of statistical techniques to project control. The book begins by defining the fundamentals of project management then explores how to temper quantitative analysis with qualitati

Design of Simulink module for dynamic reactivity simulation of marine reactor automatic control rod

International Nuclear Information System (INIS)

Chen Zhiyun; Luo Lei; Chen Wenzhen; Gui Xuewen

2010-01-01

The power of marine reactor varies frequently and acutely, which induces the frequent and acute adjustment of the automatic control rod. According to the characteristics of marine reactor and the problem of improper control rod reactivity insertion in previous literatures, the Simulink module for dynamic reactivity simulation of automatic control rod was designed and adopted as a sub-module of Simulink program for the fast calculation of the physical and thermal parameters of marine reactor. A typical dynamic process of the marine reactor was used as the benchmark, which indicates that the designed Simulink module is capable of the dynamic simulation of automatic control rod position and reactivity, and is adequate to the fast calculation of physic and thermal parameters. The Simulink module is of significant meaning to the simulation of the dynamic process of marine reactor and the fast calculation of the operating parameters. (authors)

Reactivity control in HTR power plants with respect to passive safety system. Summary

Energy Technology Data Exchange (ETDEWEB)

Barnert, H; Kugeler, K [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Sicherheitsforschung und Reaktortechnik

1996-12-01

The R and D and Demonstration of the High Temperature Reactor (HTR) is described in overview. The HTR-MODULE power plant, as the most advanced concept, is taken for the description of the reactivity control in general. The idea of the ``modularization of the core`` of the HTR has been developed as the answer on the experiences of the core melt accident at Three Miles Island. The HTR module has two shutdown systems: The ``6 rods``-system for hot shutdown at the ``18 small absorber pebbles units`` - system for cold shutdown. With respect to the definition of ``Passive Systems`` of IAEA-TECDOC-626 the total reactivity control system of the HTR-MODULE is a passive system of category D, because it is an emergency reactor shutdown system based on gravity driven rods, and devices, activated by fail-safe trip logic. But reactivity control of the HTR does not only consist of these engineered safety system but does have a self-acting stabilization by the negative temperature coefficient of the reactivity, being rather effective in reactivity control. Examples from computer calculations are presented, and, in addition, experimental results from the ``Stuck Rod Experiment`` at the AVR reactor in Juelich. On the basis of this the proposal is made that ``self-acting stabilization as a quality of the function`` should be discussed as a new category in addition to the active and passive engineered safety systems, structures and components of IAEA-TECDOC-626. The requirements for a future ``catastrophe-free`` nuclear technology are presented. In the appendix the 7th amendment of the atomic energy act of the Federal Republic of Germany, effective 28 July 94, is given. (author).

Modern integral equation techniques for quantum reactive scattering theory

International Nuclear Information System (INIS)

Auerbach, S.M.

1993-11-01

Rigorous calculations of cross sections and rate constants for elementary gas phase chemical reactions are performed for comparison with experiment, to ensure that our picture of the chemical reaction is complete. We focus on the H/D+H 2 → H 2 /DH + H reaction, and use the time independent integral equation technique in quantum reactive scattering theory. We examine the sensitivity of H+H 2 state resolved integral cross sections σ v'j',vj (E) for the transitions (v = 0,j = 0) to (v' = 1,j' = 1,3), to the difference between the Liu-Siegbahn-Truhlar-Horowitz (LSTH) and double many body expansion (DMBE) ab initio potential energy surfaces (PES). This sensitivity analysis is performed to determine the origin of a large discrepancy between experimental cross sections with sharply peaked energy dependence and theoretical ones with smooth energy dependence. We find that the LSTH and DMBE PESs give virtually identical cross sections, which lends credence to the theoretical energy dependence

plasmatis Center for Innovation Competence: Controlling reactive component output of atmospheric pressure plasmas in plasma medicine

Science.gov (United States)

Reuter, Stephan

2012-10-01

The novel approach of using plasmas in order to alter the local chemistry of cells and cell environment presents a significant development in biomedical applications. The plasmatis center for innovation competence at the INP Greifswald e.V. performs fundamental research in plasma medicine in two interdisciplinary research groups. The aim of our plasma physics research group ``Extracellular Effects'' is (a) quantitative space and time resolved diagnostics and modelling of plasmas and liquids to determine distribution and composition of reactive species (b) to control the plasma and apply differing plasma source concepts in order to produce a tailored output of reactive components and design the chemical composition of the liquids/cellular environment and (c) to identify and understand the interaction mechanisms of plasmas with liquids and biological systems. Methods to characterize the plasma generated reactive species from plasma-, gas- and liquid phase and their biological effects will be presented. The diagnostic spectrum ranges from absorption/emission/laser spectroscopy and molecular beam mass spectrometry to electron paramagnetic resonance spectroscopy and cell biological diagnostic techniques. Concluding, a presentation will be given of the comprehensive approach to plasma medicine in Greifswald where the applied and clinical research of the Campus PlasmaMed association is combined with the fundamental research at plasmatis center.

Multi-dose Romidepsin Reactivates Replication Competent SIV in Post-antiretroviral Rhesus Macaque Controllers.

Directory of Open Access Journals (Sweden)

Benjamin B Policicchio

2016-09-01

Full Text Available Viruses that persist despite seemingly effective antiretroviral treatment (ART and can reinitiate infection if treatment is stopped preclude definitive treatment of HIV-1 infected individuals, requiring lifelong ART. Among strategies proposed for targeting these viral reservoirs, the premise of the "shock and kill" strategy is to induce expression of latent proviruses [for example with histone deacetylase inhibitors (HDACis] resulting in elimination of the affected cells through viral cytolysis or immune clearance mechanisms. Yet, ex vivo studies reported that HDACis have variable efficacy for reactivating latent proviruses, and hinder immune functions. We developed a nonhuman primate model of post-treatment control of SIV through early and prolonged administration of ART and performed in vivo reactivation experiments in controller RMs, evaluating the ability of the HDACi romidepsin (RMD to reactivate SIV and the impact of RMD treatment on SIV-specific T cell responses. Ten RMs were IV-infected with a SIVsmmFTq transmitted-founder infectious molecular clone. Four RMs received conventional ART for >9 months, starting from 65 days post-infection. SIVsmmFTq plasma viremia was robustly controlled to <10 SIV RNA copies/mL with ART, without viral blips. At ART cessation, initial rebound viremia to ~106 copies/mL was followed by a decline to < 10 copies/mL, suggesting effective immune control. Three post-treatment controller RMs received three doses of RMD every 35-50 days, followed by in vivo experimental depletion of CD8+ cells using monoclonal antibody M-T807R1. RMD was well-tolerated and resulted in a rapid and massive surge in T cell activation, as well as significant virus rebounds (~104 copies/ml peaking at 5-12 days post-treatment. CD8+ cell depletion resulted in a more robust viral rebound (107 copies/ml that was controlled upon CD8+ T cell recovery. Our results show that RMD can reactivate SIV in vivo in the setting of post-ART viral control

Experimental evaluation of reactivity constraints for the closed-loop control of reactor power

International Nuclear Information System (INIS)

Bernard, J.A.; Lanning, D.D.; Ray, A.

1984-01-01

General principles for the closed-loop, digital control of reactor power have been identified, quantitatively enumerated, and experimentally demonstrated on the 5 MWt Research Reactor, MITR-II. The basic concept is to restrict the net reactivity so that it is always possible to make the reactor period infinite at the desired termination point of a transient by reversing the direction of motion of whatever control mechanism is associated with the controller. This capability is formally referred to as ''feasibility of control''. A series of ten experiments have been conducted over a period of eighteen months to demonstrate the efficacy of this property for the automatic control of reactor power. It has been shown that a controller which possesses this property is capable of both raising and lowering power in a safe, efficient manner while using a control rod of varying differential worth, that the reactivity constraints are a sufficient condition for the automatic control of reactor power, and that the use of a controller based on reactivity constraints can prevent overshoots either due to attempts to control a transient with a control rod of insufficient differential worth or due to failure to properly estimate when to commence rod insertion. Details of several of the more significant tests are presented together with a discussion of the rationale for the development of closed-loop control in large commercial power systems. Specific consideration is given to the motivation for designing a controller based on feasibility of control and the associated licensing issues

Tissue-specific control of latent CMV reactivation by regulatory T cells.

Directory of Open Access Journals (Sweden)

Maha Almanan

2017-08-01

Full Text Available Cytomegalovirus (CMV causes a persistent, lifelong infection. CMV persists in a latent state and undergoes intermittent subclinical viral reactivation that is quelled by ongoing T cell responses. While T cells are critical to maintain control of infection, the immunological factors that promote CMV persistence remain unclear. Here, we investigated the role of regulatory T cells (Treg in a mouse model of latent CMV infection using Foxp3-diphtheria toxin receptor (Foxp3-DTR mice. Eight months after infection, MCMV had established latency in the spleen, salivary gland, lung, and pancreas, which was accompanied by an increased frequency of Treg. Administration of diphtheria toxin (DT after establishment of latency efficiently depleted Treg and drove a significant increase in the numbers of functional MCMV-specific CD4+ and CD8+ T cells. Strikingly, Treg depletion decreased the number of animals with reactivatable latent MCMV in the spleen. Unexpectedly, in the same animals, ablation of Treg drove a significant increase in viral reactivation in the salivary gland that was accompanied with augmented local IL-10 production by Foxp3-CD4+T cells. Further, neutralization of IL-10 after Treg depletion significantly decreased viral load in the salivary gland. Combined, these data show that Treg have divergent control of MCMV infection depending upon the tissue. In the spleen, Treg antagonize CD8+ effector function and promote viral persistence while in the salivary gland Treg prevent IL-10 production and limit viral reactivation and replication. These data provide new insights into the organ-specific roles of Treg in controlling the reactivation of latent MCMV infection.

Control of the ambident reactivity of the nitrite ion

DEFF Research Database (Denmark)

Dong, Hai; Rahm, Martin; Thota, Niranjan

2013-01-01

of this difference was addressed. The ambident reactivity of the nitrite ion has been found to be the cause of the complex product formation observed, which can be controlled by a neighbouring equatorial ester group. Both N-attack and O-attack occur in the absence of the ester group, whereas O-attack is favoured...

Comparative study of C-Reactive Protein and other biochemical ...

African Journals Online (AJOL)

Serum levels of C-reactive proteins (CRP), Alanine aminotransferase (ALT), Aspartate aminotransferase (AST), total protein, albumin and globulins were investigated using high sensitivity Immunoturbidometric and colorimetric techniques in individuals with hepatitis (n=50), Malaria (n=50) and 40 control subjects in age ...

Extended reactivity trace curves for nuclear power control with no power shooting

Energy Technology Data Exchange (ETDEWEB)

Ratemi, W M; Elbuni, M S [Faculty of engineering, Al Fateh universty Tripoli (Libyan Arab Jamahiriya)

1995-10-01

This paper introduces a new concept of reactivity trace curve (RTC) for nuclear power control with no power shooting. The concept is based on recent work of bernard et al. on the dynamic period of nuclear reactors. RTC-method is simulated for both a static effective decay constant corresponding to a one-group delayed neutrons model, and a dynamic effective decay constant corresponding to a six-group delayed neutrons model. A fitting to the RTC of a six-group reactor model resulted in a closed from formula for the RTC that couples the effect of both static and dynamic decay constants. Hence, introducing two `fingerprints` for the reactor in concern to identify a closed from RTC formula capable of controlling the reactor power. Integration of the RTC with control rod integral curves results in the {rho}-z-t diagram. This diagram relates the amount of recommended reactivity (RTC), the position of control rod, and the time required for power control. 8 figs.

Extended reactivity trace curves for nuclear power control with no power shooting

International Nuclear Information System (INIS)

Ratemi, W. M.; Elbuni, M. S.

1995-01-01

This paper introduces a new concept of reactivity trace curve (RTC) for nuclear power control with no power shooting. The concept is based on recent work of bernard et al. on the dynamic period of nuclear reactors. RTC-method is simulated for both a static effective decay constant corresponding to a one-group delayed neutrons model, and a dynamic effective decay constant corresponding to a six-group delayed neutrons model. A fitting to the RTC of a six-group reactor model resulted in a closed from formula for the RTC that couples the effect of both static and dynamic decay constants. Hence, introducing two 'fingerprints' for the reactor in concern to identify a closed from RTC formula capable of controlling the reactor power. Integration of the RTC with control rod integral curves results in the ρ-z-t diagram. This diagram relates the amount of recommended reactivity (RTC), the position of control rod, and the time required for power control. 8 figs

Voltage Control of Distribution Grids with Multi-Microgrids Using Reactive Power Management

Directory of Open Access Journals (Sweden)

WLODARCZYK, P.

2015-02-01

Full Text Available Low-voltage Microgrids can be valuable sources of ancillary services for the Distribution System Operators (DSOs. The aim of this paper was to study if and how multi-microgrids can contribute to Voltage Control (VC in medium-voltage distribution grids by means of reactive power generation and/or absorption. The hierarchical control strategy was proposed with the main focus on the tertiary control which was defined as optimal power flow problem. The interior-point algorithm was applied to optimise experimental benchmark grid with the presence of Distributed Energy Resources (DERs. Moreover, two primary objectives were formulated: active power losses and amount of reactive power used to reach the voltage profile. As a result the active power losses were minimised to the high extent achieving the savings around 22% during entire day.

Analogical study of the servo-control of a reactivity modulator

International Nuclear Information System (INIS)

Le Bot, Michel

1969-03-01

In the context of the study of the transfer functions related to the Cabri reactor, this paper presents: the objective of the servo-control (reactivity modulator, reasons for the analogical study), the principles of the servo-control (description of the servo-controlled system, elaboration of the error signal, principles of the phase meter, critical analysis of different types of phase meters), the analogical formulation (transfer diagram of the process, analogical simulation of the process, analogical realization of the phase meter, simulation of the Low Frequency generator), study of the controlled system and results (system responses to echelon and ramp signals, responses of the controlled system with the phase meter in feedback)

Applicability of statistical process control techniques

NARCIS (Netherlands)

Schippers, W.A.J.

1998-01-01

This paper concerns the application of Process Control Techniques (PCTs) for the improvement of the technical performance of discrete production processes. Successful applications of these techniques, such as Statistical Process Control Techniques (SPC), can be found in the literature. However, some

A Hybrid Estimator for Active/Reactive Power Control of Single-Phase Distributed Generation Systems with Energy Storage

DEFF Research Database (Denmark)

Pahlevani, Majid; Eren, Suzan; Guerrero, Josep M.

2016-01-01

This paper presents a new active/reactive power closed-loop control system for a hybrid renewable energy generation system used for single-phase residential/commercial applications. The proposed active/reactive control method includes a hybrid estimator, which is able to quickly and accurately es...

Titanium dioxide-based DGT technique for in situ measurement of dissolved reactive phosphorus in fresh and marine waters

DEFF Research Database (Denmark)

Panther, Jared G.; Teasdale, Peter R.; Bennett, William W.

2010-01-01

A new diffusive gradients in a thin film (DGT) technique for measuring dissolved reactive phosphorus (DRP) in fresh and marine waters is reported. The new method, which uses a commercially available titanium dioxide based adsorbent (Metsorb), was evaluated and compared to the well-established fer...

Controls on the Environmental Fate of Compounds Controlled by Coupled Hydrologic and Reactive Processes

Science.gov (United States)

Hixson, J.; Ward, A. S.; McConville, M.; Remucal, C.

2017-12-01

Current understanding of how compounds interact with hydrologic processes or reactive processes have been well established. However, the environmental fate for compounds that interact with hydrologic AND reactive processes is not well known, yet critical in evaluating environmental risk. Evaluations of risk are often simplified to homogenize processes in space and time and to assess processes independently of one another. However, we know spatial heterogeneity and time-variable reactivities complicate predictions of environmental transport and fate, and is further complicated by the interaction of these processes, limiting our ability to accurately predict risk. Compounds that interact with both systems, such as photolytic compounds, require that both components are fully understood in order to predict transport and fate. Release of photolytic compounds occurs through both unintentional releases and intentional loadings. Evaluating risks associated with unintentional releases and implementing best management practices for intentional releases requires an in-depth understanding of the sensitivity of photolytic compounds to external controls. Lampricides, such as 3-trifluoromethyl-4-nitrophenol (TFM), are broadly applied in the Great Lakes system to control the population of invasive sea lamprey. Over-dosing can yield fish kills and other detrimental impacts. Still, planning accounts for time of passage and dilution, but not the interaction of the physical and chemical systems (i.e., storage in the hyporheic zone and time-variable decay rates). In this study, we model a series of TFM applications to test the efficacy of dosing as a function of system characteristics. Overall, our results demonstrate the complexity associated with photo-sensitive compounds through stream-hyporheic systems, and highlight the need to better understand how physical and chemical systems interact to control transport and fate in the environment.

Active-Reactive Additional Damping Control of a Doubly-Fed Induction Generator Based on Active Disturbance Rejection Control

Directory of Open Access Journals (Sweden)

Yanfeng Ma

2018-05-01

Full Text Available Large-scale wind power interfacing to the power grid has an impact on the stability of the power system. However, with an additional damping controller of the wind generator, new ways for improving system damping and suppressing the low frequency oscillation (LFO of power systems can be put forward. In this paper, an active-reactive power additional damping controller based on active disturbance rejection control (ADRC is proposed. In order to improve the precision of the controller, the theory of data driven control is adopted, using the numerical algorithms for subspace state space system identification (N4SID to obtain the two order model of the ADRC controlled object. Based on the identification model, the ADRC additional damping controller is designed. Taking a 2-area 4-machine system containing the doubly fed induction generator (DFIG wind farm as an example, it is verified that the active-reactive additional damping controller designed in this paper performs well in suppressing negative-damping LFO and forced power oscillation. When the operation state of the power system changes, it can still restrain the LFO effectively, showing stronger robustness and better effectiveness compared to the traditional proportional–integral–derivative (PID additional damping controller.

Improvement of correlated sampling Monte Carlo methods for reactivity calculations

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Asaoka, Takumi

1978-01-01

Two correlated Monte Carlo methods, the similar flight path and the identical flight path methods, have been improved to evaluate up to the second order change of the reactivity perturbation. Secondary fission neutrons produced by neutrons having passed through perturbed regions in both unperturbed and perturbed systems are followed in a way to have a strong correlation between secondary neutrons in both the systems. These techniques are incorporated into the general purpose Monte Carlo code MORSE, so as to be able to estimate also the statistical error of the calculated reactivity change. The control rod worths measured in the FCA V-3 assembly are analyzed with the present techniques, which are shown to predict the measured values within the standard deviations. The identical flight path method has revealed itself more useful than the similar flight path method for the analysis of the control rod worth. (auth.)

Associations between respiratory sinus arrhythmia (RSA) reactivity and effortful control in preschool-age children.

Science.gov (United States)

Sulik, Michael J; Eisenberg, Nancy; Spinrad, Tracy L; Silva, Kassondra M

2015-07-01

We tested whether respiratory sinus arrhythmia (RSA) reactivity in response to each of three self-regulation tasks (bird and dragon; knock-tap; and gift wrap) would predict self-regulation performance in a sample of 101 preschool-age children (M age = 4.49, SD = .64). While controlling for baseline RSA, decreases in RSA from bird and dragon to knock-tap (but not from baseline to bird and dragon) predicted a latent variable measuring self-regulation. Furthermore, increases in RSA from the knock-tap to gift wrap-the only task involving delay of gratification-were related to concurrent task performance while controlling for the relation between RSA reactivity and the latent self-regulation variable. Results suggest that the relations between RSA reactivity and self-regulatory ability are influenced by task-specific demands and possibly by task order. Furthermore, RSA reactivity appears to relate differently to performance on motivationally salient self-regulation tasks such as delay of gratification relative to cool executive function tasks. © 2015 Wiley Periodicals, Inc.

Reactive power management of power networks with wind generation

CERN Document Server

Amaris, Hortensia; Ortega, Carlos Alvarez

2012-01-01

As the energy sector shifts and changes to focus on renewable technologies, the optimization of wind power becomes a key practical issue. Reactive Power Management of Power Networks with Wind Generation brings into focus the development and application of advanced optimization techniques to the study, characterization, and assessment of voltage stability in power systems. Recent advances on reactive power management are reviewed with particular emphasis on the analysis and control of wind energy conversion systems and FACTS devices. Following an introduction, distinct chapters cover the 5 key

Robust Adaptive Reactive Power Control for Doubly Fed Induction Generator

Directory of Open Access Journals (Sweden)

Huabin Wen

2014-01-01

Full Text Available The problem of reactive power control for mains-side inverter (MSI in doubly fed induction generator (DFIG is studied in this paper. To accommodate the modelling nonlinearities and inherent uncertainties, a novel robust adaptive control algorithm for MSI is proposed by utilizing Lyapunov theory that ensures asymptotic stability of the system under unpredictable external disturbances and significant parametric uncertainties. The distinguishing benefit of the aforementioned scheme consists in its capabilities to maintain satisfactory performance under varying operation conditions without the need for manually redesigning or reprogramming the control gains in contrast to the commonly used PI/PID control. Simulations are also built to confirm the correctness and benefits of the control scheme.

Preparation of explosive nanoparticles in a porous chromium(III) oxide matrix: a first attempt to control the reactivity of explosives

International Nuclear Information System (INIS)

Comet, M; Siegert, B; Pichot, V; Gibot, P; Spitzer, D

2008-01-01

This paper reports the first attempt to control the combustion and the detonation properties of a high explosive through its structure. A porous chromium(III) oxide matrix produced by the combustion of ammonium dichromate was infiltrated by hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). The structure of the Cr 2 O 3 matrix was studied by both scanning and transmission electron microscopy (SEM, TEM); the Cr 2 O 3 /RDX nanocomposites were characterized by nitrogen adsorption. A mathematical model based on these techniques was used to demonstrate that the Cr 2 O 3 matrix encloses and stabilizes RDX particles at the nanoscale. The decomposition process of the nanocomposites was investigated by atomic force microscopy (AFM). The reactivity and sensitivity of the nanocomposites were studied by impact and friction tests, differential scanning calorimetry (DSC), time-resolved cinematography and detonation experiments, and were correlated with their structure. The size of RDX nanoparticles and their distribution in the Cr 2 O 3 matrix have an important influence on their reactivity. The reactive properties of nanostructured RDX differ significantly from those of classical micron-sized RDX. For instance, the melting point disappears and the decomposition temperature is significantly lowered. The quantization of the explosive particles in the Cr 2 O 3 matrix decreases the sensitivity to mechanical stress and allows controlling the decomposition mode-i.e. combustion versus detonation

The use of data mining techniques for analysing factors affecting cow reactivity during milking

Directory of Open Access Journals (Sweden)

Wojciech NEJA

2017-06-01

Full Text Available Motor activity of 158 Polish Holstein-Friesian cows was evaluated 5 times (before and during milking in a DeLaval 2*10 milking parlour for both the morning and evening milking, on a 5-point scale, according to the method of Budzyńska et al. (2007. The statistical analysis used multiple logistic regression and classification trees (Enterprise Miner 7.1 software which comes in with SAS package. In the evaluation of motor activity, cows that were among the first ten to enter the milking parlour were more often given a score of 3 points before (11.5% and during milking (23.5% compared to the other cows. Cows’ activity tended to decrease (both before and during milking with advancing lactation. The cows’ reduced activity was accompanied by shorter teat cup attachment times and lower milk yields. The criteria calculated for the quality of models based on classification tree technique as well as logistic regression showed that similar variables were responsible for the reactivity of cows before milking (teat cup attachment time, day of lactation, number of lactation, side of the milking parlour and during milking (day of lactation, side of the milking parlour, morning or evening milking, milk yield, number of lactation. At the same time, the applied methods showed that the determinants of the cow reactivity trait are highly complex. This complexity may be well explained using the classification tree technique.

The interactions of design, control and operability in reactive distillation systems

DEFF Research Database (Denmark)

Georgiadis, M.C.; Schenk, Myrian Andrea; Pistikopoulos, Stratos

2002-01-01

is a strong function of the process design and potential operability bottlenecks are identified. In the second approach, the process design and the control system are optimized simultaneously leading to a more economically beneficial and better controlled system than that obtained using the sequential......In this work the design and control of a reactive distillation column, described by a rigorous dynamic model, is tackled via two different optimization approaches. In the first, the steady-state process design and the control system are optimized sequentially. It is shown that operability...

Stochastic Feedforward Control Technique

Science.gov (United States)

Halyo, Nesim

1990-01-01

Class of commanded trajectories modeled as stochastic process. Advanced Transport Operating Systems (ATOPS) research and development program conducted by NASA Langley Research Center aimed at developing capabilities for increases in capacities of airports, safe and accurate flight in adverse weather conditions including shear, winds, avoidance of wake vortexes, and reduced consumption of fuel. Advances in techniques for design of modern controls and increased capabilities of digital flight computers coupled with accurate guidance information from Microwave Landing System (MLS). Stochastic feedforward control technique developed within context of ATOPS program.

Proactive and reactive control depends on emotional valence: a Stroop study with emotional expressions and words.

Science.gov (United States)

Kar, Bhoomika Rastogi; Srinivasan, Narayanan; Nehabala, Yagyima; Nigam, Richa

2018-03-01

We examined proactive and reactive control effects in the context of task-relevant happy, sad, and angry facial expressions on a face-word Stroop task. Participants identified the emotion expressed by a face that contained a congruent or incongruent emotional word (happy/sad/angry). Proactive control effects were measured in terms of the reduction in Stroop interference (difference between incongruent and congruent trials) as a function of previous trial emotion and previous trial congruence. Reactive control effects were measured in terms of the reduction in Stroop interference as a function of current trial emotion and previous trial congruence. Previous trial negative emotions exert greater influence on proactive control than the positive emotion. Sad faces in the previous trial resulted in greater reduction in the Stroop interference for happy faces in the current trial. However, current trial angry faces showed stronger adaptation effects compared to happy faces. Thus, both proactive and reactive control mechanisms are dependent on emotional valence of task-relevant stimuli.

Acceptance lowers stress reactivity: Dismantling mindfulness training in a randomized controlled trial.

Science.gov (United States)

Lindsay, Emily K; Young, Shinzen; Smyth, Joshua M; Brown, Kirk Warren; Creswell, J David

2018-01-01

Mindfulness interventions, which train practitioners to monitor their present-moment experience with a lens of acceptance, are known to buffer stress reactivity. Little is known about the active mechanisms driving these effects. We theorize that acceptance is a critical emotion regulation mechanism underlying mindfulness stress reduction effects. In this three-arm parallel trial, mindfulness components were dismantled into three structurally equivalent 15-lesson smartphone-based interventions: (1) training in both monitoring and acceptance (Monitor+Accept), (2) training in monitoring only (Monitor Only), or (3) active control training (Coping control). 153 stressed adults (mean age=32years; 67% female; 53% white, 21.5% black, 21.5% Asian, 4% other race) were randomly assigned to complete one of three interventions. After the intervention, cortisol, blood pressure, and subjective stress reactivity were assessed using a modified Trier Social Stress Test. As predicted, Monitor+Accept training reduced cortisol and systolic blood pressure reactivity compared to Monitor Only and control trainings. Participants in all three conditions reported moderate levels of subjective stress. This study provides the first experimental evidence that brief smartphone mindfulness training can impact stress biology, and that acceptance training drives these effects. We discuss implications for basic and applied research in contemplative science, emotion regulation, stress and coping, health, and clinical interventions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Design techniques for mutlivariable flight control systems

Science.gov (United States)

1981-01-01

Techniques which address the multi-input closely coupled nature of advanced flight control applications and digital implementation issues are described and illustrated through flight control examples. The techniques described seek to exploit the advantages of traditional techniques in treating conventional feedback control design specifications and the simplicity of modern approaches for multivariable control system design.

Operational experience with reactive power control methods optimized for tokamak power supplies

International Nuclear Information System (INIS)

Sihler, C.; Huart, M.; Kaesemann, C.-P.; Streibl, B.

2003-01-01

The power and energy of the ASDEX Upgrade (AUG) tokamak are provided by two separate 10.5 kV, 110-85 Hz networks based on the flywheel generators EZ3-EZ4 in addition to the generator EZ2 dedicated to the toroidal field coil. The 10.5 kV networks supply the thyristor converters allowing fast control of the DC currents in the AUG poloidal field coils. Two methods for improving the load power factor in the present experimental campaign of AUG have been investigated, namely the control of the phase-to-neutral voltage in thyristor converters fitted with neutral thyristors, such as the new 145 MVA modular thyristor converter system (Group 6), and reactive power control achieved by means of static VAr compensators (SVC). The paper shows that reliable compensation up to 90 MVAr was regularly achieved and that electrical transients in SVC modules can be kept at an acceptable level. The paper will discuss the results from the reactive power reduction by SVC and neutral thyristor control and draw a comparative conclusion

3D-QSPR Method of Computational Technique Applied on Red Reactive Dyes by Using CoMFA Strategy

Directory of Open Access Journals (Sweden)

Shahnaz Perveen

2011-12-01

Full Text Available Cellulose fiber is a tremendous natural resource that has broad application in various productions including the textile industry. The dyes, which are commonly used for cellulose printing, are “reactive dyes” because of their high wet fastness and brilliant colors. The interaction of various dyes with the cellulose fiber depends upon the physiochemical properties that are governed by specific features of the dye molecule. The binding pattern of the reactive dye with cellulose fiber is called the ligand-receptor concept. In the current study, the three dimensional quantitative structure property relationship (3D-QSPR technique was applied to understand the red reactive dyes interactions with the cellulose by the Comparative Molecular Field Analysis (CoMFA method. This method was successfully utilized to predict a reliable model. The predicted model gives satisfactory statistical results and in the light of these, it was further analyzed. Additionally, the graphical outcomes (contour maps help us to understand the modification pattern and to correlate the structural changes with respect to the absorptivity. Furthermore, the final selected model has potential to assist in understanding the charachteristics of the external test set. The study could be helpful to design new reactive dyes with better affinity and selectivity for the cellulose fiber.

3D-QSPR method of computational technique applied on red reactive dyes by using CoMFA strategy.

Science.gov (United States)

Mahmood, Uzma; Rashid, Sitara; Ali, S Ishrat; Parveen, Rasheeda; Zaheer-Ul-Haq; Ambreen, Nida; Khan, Khalid Mohammed; Perveen, Shahnaz; Voelter, Wolfgang

2011-01-01

Cellulose fiber is a tremendous natural resource that has broad application in various productions including the textile industry. The dyes, which are commonly used for cellulose printing, are "reactive dyes" because of their high wet fastness and brilliant colors. The interaction of various dyes with the cellulose fiber depends upon the physiochemical properties that are governed by specific features of the dye molecule. The binding pattern of the reactive dye with cellulose fiber is called the ligand-receptor concept. In the current study, the three dimensional quantitative structure property relationship (3D-QSPR) technique was applied to understand the red reactive dyes interactions with the cellulose by the Comparative Molecular Field Analysis (CoMFA) method. This method was successfully utilized to predict a reliable model. The predicted model gives satisfactory statistical results and in the light of these, it was further analyzed. Additionally, the graphical outcomes (contour maps) help us to understand the modification pattern and to correlate the structural changes with respect to the absorptivity. Furthermore, the final selected model has potential to assist in understanding the characteristics of the external test set. The study could be helpful to design new reactive dyes with better affinity and selectivity for the cellulose fiber.

Do measures of reactive balance control predict falls in people with stroke returning to the community?

Science.gov (United States)

Mansfield, A; Wong, J S; McIlroy, W E; Biasin, L; Brunton, K; Bayley, M; Inness, E L

2015-12-01

To determine if reactive balance control measures predict falls after discharge from stroke rehabilitation. Prospective cohort study. Rehabilitation hospital and community. Independently ambulatory individuals with stroke who were discharged home after inpatient rehabilitation (n=95). Balance and gait measures were obtained from a clinical assessment at discharge from inpatient stroke rehabilitation. Measures of reactive balance control were obtained: (1) during quiet standing; (2) when walking; and (3) in response to large postural perturbations. Participants reported falls and activity levels up to 6 months post-discharge. Logistic and Poisson regressions were used to identify measures of reactive balance control that were related to falls post-discharge. Decreased paretic limb contribution to standing balance control [rate ratio 0.8, 95% confidence interval (CI) 0.7 to 1.0; P=0.011], reduced between-limb synchronisation of quiet standing balance control (rate ratio 0.9, 95% CI 0.8 to 0.9; Pfall rates when controlling for age, stroke severity, functional balance and daily walking activity. Impaired reactive balance control in standing and walking predicted increased risk of falls post-discharge from stroke rehabilitation. Specifically, measures that revealed the capacity of both limbs to respond to instability were related to increased risk of falls. These results suggest that post-stroke rehabilitation strategies for falls prevention should train responses to instability, and focus on remediating dyscontrol in the more-affected limb. Copyright © 2015 Chartered Society of Physiotherapy. Published by Elsevier Ltd. All rights reserved.

Tokamak impurity-control techniques

International Nuclear Information System (INIS)

Schmidt, J.A.

1980-01-01

A brief review is given of the impurity-control functions in tokamaks, their relative merits and disadvantages and some prominent edge-interaction-control techniques, and there is a discussion of a new proposal, the particle scraper, and its potential advantages. (author)

Present art of reactivity determination

International Nuclear Information System (INIS)

Kaneko, Yoshihiko; Nakano, Masafumi; Matsuura, Shojiro

1977-01-01

Experimental techniques for reactivity determination of a reactor have been one of the long standing subjects in reactor physics. Recently, such a requirement was proposed by the reactor designers and operators that the values of reactivity should be measured more accurately. This is because importance is emphasized for the role of reactivity to the performance of reactor safety, economics and operability. Motivated by the requirement, some remarkable progresses are being made for the improvement of the experimental techniques. Then, the present review summarizes the research activities on this subject, identifies several reactor physics problems to be overcome, and makes mention of the future targets. (auth.)

EKF composition estimation and GMC control of a reactive distillation column

Science.gov (United States)

Tintavon, Sirivimon; Kittisupakorn, Paisan

2017-08-01

This research work proposes an extended Kalman filter (EKF) estimator to give estimates of product composition and a generic model controller (GMC) to control the temperature of a reactive distillation column (RDC). One of major difficulties to control the RDC is large time delays of product composition measurement. Therefore, the estimates of the product composition are needed and determined based on available and reliable measured tray temperature via the extended Kalman Filter (EKF). With these estimates, the GMC controller is applied to control the RDC's temperature. The performance of the EKF estimator under the GMC control is evaluated in various disturbances and set point change.

Core calculational techniques and procedures

International Nuclear Information System (INIS)

Romano, J.J.

1977-10-01

Described are the procedures and techniques employed by B and W in core design analyses of power peaking, control rod worths, and reactivity coefficients. Major emphasis has been placed on current calculational tools and the most frequently performed calculations over the operating power range

Optimising Reactive Control in non-ideal Efficiency Wave Energy Converters

DEFF Research Database (Denmark)

Strager, Thomas; Lopez, Pablo Fernandez; Giorgio, Giuseppe

2014-01-01

When analytically optimising the control strategy in wave energy converters which use a point absorber, the efficiency aspect is generally neglected. The results presented in this paper provide an analytical expression for the mean harvested electrical power in non-ideal efficiency situations....... These have been derived under the assumptions of monochromatic incoming waves and linear system behaviour. This allows to establish the power factor of a system with non-ideal efficiency. The locus of the optimal reactive control parameters is then studied and an alternative method of representation...... is developed to model the optimal control parameters. Ultimately we present a simple method of choosing optimal control parameters for any combination of efficiency and wave frequency....

Development of a robust model-based reactivity control system

International Nuclear Information System (INIS)

Rovere, L.A.; Otaduy, P.J.; Brittain, C.R.

1990-01-01

This paper describes the development and implementation of a digital model-based reactivity control system that incorporates a knowledge of the plant physics into the control algorithm to improve system performance. This controller is composed of a model-based module and modified proportional-integral-derivative (PID) module. The model-based module has an estimation component to synthesize unmeasurable process variables that are necessary for the control action computation. These estimated variables, besides being used within the control algorithm, will be used for diagnostic purposes by a supervisory control system under development. The PID module compensates for inaccuracies in model coefficients by supplementing the model-based output with a correction term that eliminates any demand tracking or steady state errors. This control algorithm has been applied to develop controllers for a simulation of liquid metal reactors in a multimodular plant. It has shown its capability to track demands in neutron power much more accurately than conventional controllers, reducing overshoots to almost negligible value while providing a good degree of robustness to unmodeled dynamics. 10 refs., 4 figs

Thermoset polymers chemo-rheology dedicated to reactive rotational moulding (RRM) understanding and control

International Nuclear Information System (INIS)

Viale, J.

2009-12-01

This study comes within the scope of New Technology for Energy, particularly for high pressure hydrogen storage. Reactive Rotational Moulding has been identified as an adapted process for hydrogen-tight liners manufacturing. Thus the Reactive Rotational Moulding process has been studied in order to find theoretical tools dedicated to the understanding of such a reactive forming process. Chemical kinetics of four polyurethanes and poly-epoxides reactive systems have been determined on classical isothermal conditions and original aniso-thermal conditions i.e. on temperature ramps. Aniso-thermal conditions have been selected because they corresponds better to real process conditions. Rheological behaviour have also been characterized on two different approaches, an isothermal one and on temperature ramps. In particular, viscosity have been described as a function of heating rate. These physical and chemical results have been compiled in an original state diagram in order to show material properties evolution in a time-temperature space. The whole ex situ characterizations are then managed to described the behavior of the different formulations during the rotational moulding. Moreover they allow to form specific materials and so to widen the range of material to thermoset polymers. Finally, in order to correlate theoretical deduction to real reactive systems evolution, the elaboration of innovating monitoring tool based on ultrasonic analysis has been studied. To begin, polymerization monitoring criteria have been identified and then specific techniques have been set to monitor these criteria in real forming process. (author)

Reactive dispersive contaminant transport in coastal aquifers: Numerical simulation of a reactive Henry problem

KAUST Repository

Nick, H.M.

2013-02-01

The reactive mixing between seawater and terrestrial water in coastal aquifers influences the water quality of submarine groundwater discharge. While these waters come into contact at the seawater groundwater interface by density driven flow, their chemical components dilute and react through dispersion. A larger interface and wider mixing zone may provide favorable conditions for the natural attenuation of contaminant plumes. It has been claimed that the extent of this mixing is controlled by both, porous media properties and flow conditions. In this study, the interplay between dispersion and reactive processes in coastal aquifers is investigated by means of numerical experiments. Particularly, the impact of dispersion coefficients, the velocity field induced by density driven flow and chemical component reactivities on reactive transport in such aquifers is studied. To do this, a hybrid finite-element finite-volume method and a reactive simulator are coupled, and model accuracy and applicability are assessed. A simple redox reaction is considered to describe the degradation of a contaminant which requires mixing of the contaminated groundwater and the seawater containing the terminal electron acceptor. The resulting degradation is observed for different scenarios considering different magnitudes of dispersion and chemical reactivity. Three reactive transport regimes are found: reaction controlled, reaction-dispersion controlled and dispersion controlled. Computational results suggest that the chemical components\\' reactivity as well as dispersion coefficients play a significant role on controlling reactive mixing zones and extent of contaminant removal in coastal aquifers. Further, our results confirm that the dilution index is a better alternative to the second central spatial moment of a plume to describe the mixing of reactive solutes in coastal aquifers. © 2012 Elsevier B.V.

Inverse kinetics technique for reactor shutdown measurement: an experimental assessment. [AGR

Energy Technology Data Exchange (ETDEWEB)

Lewis, T. A.; McDonald, D.

1975-09-15

It is proposed to use the Inverse Kinetics Technique to measure the subcritical reactivity as a function of time during the testing of the nitrogen injection systems on AGRs. A description is given of an experimental assessment of the technique by investigating known transients created by control rod movements on a small experimental reactor, (2m high, 1m radius). Spatial effects were observed close to the moving rods but otherwise derived reactivities were independent of detector position and agreed well with the existing calibrations. This prompted the suggestion that data from installed reactor instrumentation could be used to calibrate CAGR control rods.

Possibilities and limits of the reactivity determination of control rods

International Nuclear Information System (INIS)

Buenemann, D.

1975-01-01

Basic physical facts of the reactivity determination of control rods are presented. A survey of currrently applied methods is given, and the drawbacks of the various methods are pointed out. Special problems are presented by the interpretation of highly subcritical assemblies which are not really important in practical reactor operation but desirable for a consistant comparison between theory and experiments. (orig./AK) [de

Effect of drop jump technique on the reactive strength index

Directory of Open Access Journals (Sweden)

Struzik Artur

2016-09-01

Full Text Available The basic drill of plyometric training aimed at improving lower limb power and jump height is a drop jump. This exercise can be performed using different techniques, which substantially affects jump variables. Therefore, the aim of this study was to compare the values of the reactive strength index (RSI for countermovement drop jumps (CDJs and bounce drop jumps (BDJs. The study was carried out in a group of 8 male youth basketball players. The tests were conducted using the AMTI BP600900 force plate to measure ground reaction forces and the Noraxon MyoMotion system to record kinematic data. Each player performed two CDJs and two BDJs from the height of 15, 30, 45 and 60 cm. The RSI was calculated as a ratio of jump height and contact time. Moreover, the RSI was determined for the amortization and take-off phases separately. Significant differences (p < 0.05 between RSI values for CDJs and BDJs were recorded for jumps from 30, 45 and 60 cm. Differences in RSI values for jumps from 15 cm were not significant. Furthermore, CDJ height values were significantly higher (p < 0.05 than the values recorded for BDJs. Times of contact, amortization and take-off during BDJs were significantly shorter (p < 0.05 than the respective values obtained for CDJs. Therefore, the use of the RSI to monitor plyometric training should be based on the drop jump technique that is commonly performed by basketball players.

Reactivity-based industrial volatile organic compounds emission inventory and its implications for ozone control strategies in China

Science.gov (United States)

Liang, Xiaoming; Chen, Xiaofang; Zhang, Jiani; Shi, Tianli; Sun, Xibo; Fan, Liya; Wang, Liming; Ye, Daiqi

2017-08-01

Increasingly serious ozone (O3) pollution, along with decreasing NOx emission, is creating a big challenge in the control of volatile organic compounds (VOCs) in China. More efficient and effective measures are assuredly needed for controlling VOCs. In this study, a reactivity-based industrial VOCs emission inventory was established in China based on the concept of ozone formation potential (OFP). Key VOCs species, major VOCs sources, and dominant regions with high reactivity were identified. Our results show that the top 15 OFP-based species, including m/p-xylene, toluene, propene, o-xylene, and ethyl benzene, contribute 69% of the total OFP but only 30% of the total emission. The architectural decoration industry, oil refinery industry, storage and transport, and seven other sources constituted the top 10 OFP subsectors, together contributing a total of 85%. The provincial and spatial characteristics of OFP are generally consistent with those of mass-based inventory. The implications for O3 control strategies in China are discussed. We propose a reactivity-based national definition of VOCs and low-reactive substitution strategies, combined with evaluations of health risks. Priority should be given to the top 15 or more species with high reactivity through their major emission sources. Reactivity-based policies should be flexibly applied for O3 mitigation based on the sensitivity of O3 formation conditions.

Neutronic characterization of cylindrical core of minor excess reactivity in the nuclear reactor IPEN/MB-01 from the measure of neutron flux distribution and its reactivity ratio

Energy Technology Data Exchange (ETDEWEB)

Bitelli, Ulysses d' Utra; Aredes, Vitor O.G.; Mura, Luiz E.C.; Santos, Diogo F. dos; Silva, Alexandre P. da, E-mail: ubitelli@ipen.br, E-mail: vitoraredes@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

When compared to a rectangular parallelepiped configuration the cylindrical configuration of a nuclear reactor core has a better neutron economy because in this configuration the probability of the neutron leakage is smaller, causing an increase in overall reactivity in the system to the same amount of fuel used. In this work we obtained a critical cylindrical configuration with the control rods 89.50% withdraw from the active region of the IPEN/MB-01 core. This is the cylindrical configuration minimum possible excess of reactivity. Thus we obtained a cylindrical configuration with a diameter of only 28 fuel rods with lowest possible excess of reactivity. For this purpose, 112 peripheral fuel rods are removed from standard reactor core (rectangular parallelepiped of 28x28 fuel rods). In this configuration the excesses of reactivity is approximated 279 pcm. From there, we characterize the neutron field by measuring the spatial distribution of the thermal and epithermal neutron flux for the reactor operating power of 83 watts measured by neutron noise analysis technique and 92.08± 0.07 watts measured by activation technique [10]. The values of thermal and epithermal neutron flux in different directions, axial, radial north-south and radial east-west, are obtained in the asymptotic region of the reactor core, away from the disturbances caused by the reflector and control bar, by irradiating thin gold foils infinitely diluted (1% Au - 99% Al) with and without (bare) cadmium cover. In addition to the distribution of neutron flux, the moderator temperature coefficient, the void coefficient, calibration of the control rods were measured. (author)

Application of a Virtual Reactivity Feedback Control Loop in Non-Nuclear Testing of a Fast Spectrum Reactor

International Nuclear Information System (INIS)

Bragg-Sitton, Shannon M.; Forsbacka, Matthew

2004-01-01

For a compact, fast-spectrum reactor, reactivity feedback is dominated by core deformation at elevated temperature. Given the use of accurate deformation measurement techniques, it is possible to simulate nuclear feedback in non-nuclear electrically heated reactor tests. Implementation of simulated reactivity feedback in response to measured deflection is being tested at the Nasa Marshall Space Flight Center Early Flight Fission Test Facility (EFF-TF). During tests of the SAFE-100 reactor prototype, core deflection was monitored using a high resolution camera. 'Virtual' reactivity feedback was accomplished by applying the results of Monte Carlo calculations (MCNPX) to core deflection measurements; the computational analysis was used to establish the reactivity worth of various core deformations. The power delivered to the SAFE-100 prototype was then adjusted accordingly via kinetics calculations. The work presented in this paper will demonstrate virtual reactivity feedback as core power was increased from 1 kWt to 10 kWt, held approximately constant at 10 kWt, and then allowed to decrease based on the negative thermal reactivity coefficient. (authors)

Controlled Growth of ZnSe Nanocrystals by Tuning Reactivity and Amount of Zinc Precursor

Directory of Open Access Journals (Sweden)

Lai-Jun Zhang

2013-01-01

Full Text Available Zinc selenide (ZnSe nanocrystals were synthesized via a phosphine-free route using the highly reactive alkylamine-H2Se complex as selenium precursor and zinc precursors with different reactivity. The reactivity of zinc precursor was tuned by using three kinds of zinc carboxylates with different alkyl chain lengths, including zinc acetate, zinc nonanoate, and zinc stearate. The effect of the reactivity and the amount of zinc precursor on nucleation and growth of ZnSe nanocrystals were investigated by ultraviolet-visible absorption and photoluminescence spectra. Result indicates that the growth and optical property of the resulting ZnSe nanocrystals are strongly dependent on the alkyl chain length and the amount of the zinc carboxylates and both shorter alkyl chain length, and more amount of zinc carboxylate will lead to faster growth of ZnSe nanocrystals. This allows that the controlled growth and excellent optical property of high-quality ZnSe nanocrystals can be achieved by combining the different reactivity and the used amount of zinc precursor, such as by using stoichiometric and reactive Zn precursor and Se precursor or by using larger amount of more unreactive Zn precursor relative to the highly reactive alkylamine-H2Se complex precursor.

Preparation of explosive nanoparticles in a porous chromium(III) oxide matrix: a first attempt to control the reactivity of explosives

Energy Technology Data Exchange (ETDEWEB)

Comet, M; Siegert, B; Pichot, V; Gibot, P; Spitzer, D [Laboratoire ISL/CNRS ' Nanomateriaux pour les Systemes Sous Sollicitations Extremes' (NS3E), FRE 3026, French-German Research Institute of Saint-Louis (ISL), 5 rue du General Cassagnou, 68301 Saint-Louis (France)], E-mail: comet@isl.tm.fr

2008-07-16

This paper reports the first attempt to control the combustion and the detonation properties of a high explosive through its structure. A porous chromium(III) oxide matrix produced by the combustion of ammonium dichromate was infiltrated by hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). The structure of the Cr{sub 2}O{sub 3} matrix was studied by both scanning and transmission electron microscopy (SEM, TEM); the Cr{sub 2}O{sub 3}/RDX nanocomposites were characterized by nitrogen adsorption. A mathematical model based on these techniques was used to demonstrate that the Cr{sub 2}O{sub 3} matrix encloses and stabilizes RDX particles at the nanoscale. The decomposition process of the nanocomposites was investigated by atomic force microscopy (AFM). The reactivity and sensitivity of the nanocomposites were studied by impact and friction tests, differential scanning calorimetry (DSC), time-resolved cinematography and detonation experiments, and were correlated with their structure. The size of RDX nanoparticles and their distribution in the Cr{sub 2}O{sub 3} matrix have an important influence on their reactivity. The reactive properties of nanostructured RDX differ significantly from those of classical micron-sized RDX. For instance, the melting point disappears and the decomposition temperature is significantly lowered. The quantization of the explosive particles in the Cr{sub 2}O{sub 3} matrix decreases the sensitivity to mechanical stress and allows controlling the decomposition mode-i.e. combustion versus detonation.

Calculation of the Reactivity Equivalence of Control Rods in the Second Charge of the HBWR

International Nuclear Information System (INIS)

Weissglas, P.

1960-11-01

Full text: Using current methods the reactivity equivalence of 19 31 and 37 centrally located control rods in the second charge of the HBWR has been calculated. An estimate of the available excess reactivity with clean cold core has also been made. Insertion depth was taken as 0, l/3, 2/3 and 3/3 of the core length

Calculation of the Reactivity Equivalence of Control Rods in the Second Charge of the HBWR.

Energy Technology Data Exchange (ETDEWEB)

Weissglas, P [The Swedish State Power Board, Stockholm (Sweden)

1960-11-15

Full text: Using current methods the reactivity equivalence of 19 31 and 37 centrally located control rods in the second charge of the HBWR has been calculated. An estimate of the available excess reactivity with clean cold core has also been made. Insertion depth was taken as 0, l/3, 2/3 and 3/3 of the core length.

Autonomous Control of Current and Voltage Controlled DG Interface Inverters for Reactive Power Sharing and Harmonics Compensation in Islanded Microgrids

DEFF Research Database (Denmark)

Mousazadeh, Seyyed Yousef; Jalilain, Alireza; Savaghebi, Mehdi

2018-01-01

In microgrids, Voltage Source Inverters (VSIs) interfacing Distributed Generation (DG) units can be operated in Voltage or Current Controlled Modes (VCM/CCM). In this paper, a coordinated control of CCM and VCM units for reactive power sharing and voltage harmonics compensation is proposed....... This decentralized control scheme is based on the local measurement of signals. In this way, the need for communication links is removed which results in a simpler and more reliable structure compared to the communication based control structures. To be more exact, the VCM units contribute to harmonics compensation....... Experimental and simulation studies show that the harmonics compensation is achieved by using only local measurements in presence of virtual admittance/impedance schemes of CCM/VCM units. Furthermore, it is demonstrated that the reactive power sharing among the CCM and VCM units is obtained based...

Application of noise analysis technique for monitoring the moderator temperature coefficient of reactivity in pressurized water reactors

International Nuclear Information System (INIS)

Shieh, D.J.; Upadhyaya, B.R.; Sweeney, F.J.

1987-01-01

A new technique, based on the noise analysis of neutron detector and core-exit coolant temperature signals, is developed for monitoring the moderator temperature coefficient of reactivity in pressurized water reactors (PWRs). A detailed multinodal model is developed and evaluated for the reactor core subsystem of the loss-of-fluid test (LOFT) reactor. This model is used to study the effect of changing the sign of the moderator temperature coefficient of reactivity on the low-frequency phase angle relationship between the neutron detector and the core-exit temperature noise signals. Results show that the phase angle near zero frequency approaches - 180 deg for negative coefficients and 0 deg for positive coefficients when the perturbation source for the noise signals is core coolant flow, inlet coolant temperature, or random heat transfer

Digital reactivity meter

International Nuclear Information System (INIS)

Copie, M.; Valantic, B.

1978-01-01

Digital reactivity meters (DRM) are mostly used as measuring instruments, e.g. for calibration of control rods, and there are only a few cases of their incorporation into the control systems of the reactors. To move in this direction there is more development work needed. First of all, fast algorithms are needed for inverse kinetics equations to relieve the computer for more important tasks of reactor model solving in real time. The next problem, currently under investigation, is the incorporation of the reactor thermal-hydraulic model into the DRM so that it can be used in the power range. Such an extension of DHM allows presentation not only of the instantaneous reactivity of the system, but also the inserted reactivity can be estimated from the temperature reactivity feed-backs. One of the applications of this concept is the anomalous digital reactivity monitor (ADRN) as part of the reactor protection system. As a solution of the first problem, a fast algorithm for solving the inverse kinetics equations has been implemented in the off-line program RODCAL on CDC 1700 computer and tested for its accuracy by performing different control rod calibrations on the reactor TRIGA

The Effect of Aging on the Dynamics of Reactive and Proactive Cognitive Control of Response Interference.

Science.gov (United States)

Xiang, Ling; Zhang, Baoqiang; Wang, Baoxi; Jiang, Jun; Zhang, Fenghua; Hu, Zhujing

2016-01-01

A prime-target interference task was used to investigate the effects of cognitive aging on reactive and proactive control after eliminating frequency confounds and feature repetitions from the cognitive control measures. We used distributional analyses to explore the dynamics of the two control functions by distinguishing the strength of incorrect response capture and the efficiency of suppression control. For reactive control, within-trial conflict control and between-trial conflict adaption were analyzed. The statistical analysis showed that there were no reliable between-trial conflict adaption effects for either young or older adults. For within-trial conflict control, the results revealed that older adults showed larger interference effects on mean RT and mean accuracy. Distributional analyses showed that the decline mainly stemmed from inefficient suppression rather than from stronger incorrect responses. For proactive control, older adults showed comparable proactive conflict resolution to young adults on mean RT and mean accuracy. Distributional analyses showed that older adults were as effective as younger adults in adjusting their responses based on congruency proportion information to minimize automatic response capture and actively suppress the direct response activation. The results suggest that older adults were less proficient at suppressing interference after conflict was detected but can anticipate and prevent inference in response to congruency proportion manipulation. These results challenge earlier views that older adults have selective deficits in proactive control but intact reactive control.

Reactive dual magnetron sputtering for large area application

International Nuclear Information System (INIS)

Struempfel, J.

2002-01-01

Production lines for large area coating demand high productivity of reactive magnetron sputtering processes. Increased dynamic deposition rates for oxides and nitrides were already obtained by using of highly powered magnetrons in combination with advanced sputter techniques. However, besides high deposition rates the uniformity of such coatings has to be carefully considered. First the basics of reactive sputtering processes and dual magnetron sputtering are summarized. Different methods for process stabilization and control are commonly used for reactive sputtering. The Plasma Emission Monitor (PE M) offers the prerequisite for fast acting process control derived from the in-situ intensity measurements of a spectral line of the sputtered target material. Combined by multiple Plasma Emission Monitor control loops segmented gas manifolds are able to provide excellent thin film uniformity at high deposition rates. The Dual Magnetron allows a broad range of processing by different power supply modes. Medium frequency, DC and pulsed DC power supplies can be used for high quality layers. Whereas the large area coating of highly isolating layers like TiO 2 or SiO 2 is dominated by MF sputtering best results for coating with transparent conductive oxides are obtained by dual DC powering of the dual magnetron arrangement. (Author)

Microcomputer-based equipment-control and data-acquisition system for fission-reactor reactivity-worth measurements

International Nuclear Information System (INIS)

McDowell, W.P.; Bucher, R.G.

1980-01-01

Material reactivity-worth measurements are one of the major classes of experiments conducted on the Zero Power research reactors (ZPR) at Argonne National Laboratory. These measurements require the monitoring of the position of a servo control element as a sample material is positioned at various locations in a critical reactor configuration. In order to guarantee operational reliability and increase experimental flexibility for these measurements, the obsolete hardware-based control unit has been replaced with a microcomputer based equipment control and data acquisition system. This system is based on an S-100 bus, dual floppy disk computer with custom built cards to interface with the experimental system. To measure reactivity worths, the system accurately positions samples in the reactor core and acquires data on the position of the servo control element. The data are then analyzed to determine statistical adequacy. The paper covers both the hardware and software aspects of the design

Microcomputer-based equipment-control and data-acquisition system for fission-reactor reactivity-worth measurements

Energy Technology Data Exchange (ETDEWEB)

McDowell, W.P.; Bucher, R.G.

1980-01-01

Material reactivity-worth measurements are one of the major classes of experiments conducted on the Zero Power research reactors (ZPR) at Argonne National Laboratory. These measurements require the monitoring of the position of a servo control element as a sample material is positioned at various locations in a critical reactor configuration. In order to guarantee operational reliability and increase experimental flexibility for these measurements, the obsolete hardware-based control unit has been replaced with a microcomputer based equipment control and data acquisition system. This system is based on an S-100 bus, dual floppy disk computer with custom built cards to interface with the experimental system. To measure reactivity worths, the system accurately positions samples in the reactor core and acquires data on the position of the servo control element. The data are then analyzed to determine statistical adequacy. The paper covers both the hardware and software aspects of the design.

Sensory organisation and reactive balance control of amateur rugby players: A cross-sectional study.

Science.gov (United States)

Chow, Gary C C; Chung, Joanne W Y; Ma, Ada W W; Macfarlane, Duncan J; Fong, Shirley S M

2017-05-01

This study compared the sensory organisation and reactive balance control of amateur rugby players and a control group. Forty-one amateur rugby players (22 males: 19 females; mean height ± SD = 168.8 ± 8.8 cm; mean weight ± SD = 63.9 ± 12.5 kg) and 31 control participants (22 males: 9 females; mean height ± SD = 171.5 ± 10.3 cm; mean weight ± SD = 63.8 ± 10.3 kg) completed the study. Their sensory organisation and standing balance performance were evaluated using a sensory organisation test (SOT), and their reactive balance performance was quantified using a motor control test (MCT). The SOT equilibrium scores (ES) and sensory ratios and the MCT motor response latencies were the major outcome measures. The results revealed that compared to the controls, amateur rugby players had lower SOT ESs under different sensory environments (P rugby group (P = .005, [Formula: see text] = 0.107 and 0.108, respectively). No significant difference was found in the somatosensory ratio (P = .853, [Formula: see text] rugby players demonstrated inferior standing balance performance compared to their non-trained counterparts. They relied less heavily on vestibular and visual inputs to maintain standing balance under different sensory environments. In addition, they reacted more slowly to postural disturbance, reflecting their suboptimal reactive balance ability in standing.

Regarding KUR Reactivity Measurement System

International Nuclear Information System (INIS)

Nakamori, Akira; Hasegawa, Kei; Tsuchiyama, Tatsuo; Yamamoto, Toshihiro; Okumura, Ryo; Sano, Tadafumi

2012-01-01

This article reported: (1) the outline of the reactivity measurement system of Kyoto University Research Reactor (KUR), (2) the calibration data of control rod, (3) the problems and the countermeasures for range switching of linear output meter. For the laptop PC for the reactivity measurement system, there are four input signals: (1) linear output meter, (2) logarithmic output meter, (3) core temperature gauge, and (4) control rod position. The hardware of reactivity measurement system is controlled with Labview installed on the laptop. Output, reactivity, reactor period, and the change in reactivity due to temperature effect or Xenon effect are internally calculated and displayed in real-time with Labview based on the four signals above. Calculation results are recorded in the form of a spreadsheet. At KUR, the reactor core arrangement was changed, so the control rod was re-calibrated. At this time, calculated and experimental values of reactivity based on the reactivity measurement system were compared, and it was confirmed that the reactivity calculation by Labview was accurate. The range switching of linear output meter in the nuclear instrumentation should automatically change within the laptop, however sometimes this did not function properly in the early stage. It was speculated that undefined percent values during the transition of percent value were included in the calculation and caused calculation errors. The range switching started working properly after fixing this issue. (S.K.)

PERL-2 and LAVR-2 programs for Monte Carlo calculation of reactivity disturbances with trajectory correlation using random numbers

International Nuclear Information System (INIS)

Kamaeva, O.B.; Polevoj, V.B.

1983-01-01

Realization of BESM-6 computer of a technique is described for calculating a wide class of reactivity disturbances by plotting trajectories in undisturbed and disturbed systems using one sequence of random numbers. The technique was realized on the base of earlier created programs of calculation of widespreed (PERL) and local (LAVR) reactivity disturbances. The efficiency of the technique and programs is demonstrated by calculation of change of effective neutron-multiplication factor when absorber is substituted for fuel element in a BFS-40 critical assembly and by calculation of control drum characteristics

Study of the controllable reactivity of aluminum alloys and their promising application for hydrogen generation

International Nuclear Information System (INIS)

Fan Meiqiang; Sun Lixian; Xu Fen

2010-01-01

The hydrolysis performances of two aluminum alloys are investigated as their reactivity can be controlled via the different additives. The additive of NaCl has the positive effect to improve the hydrolysis properties of the aluminum alloys with quicker hydrolysis kinetic and lower hydrolysis temperature. For examples, in 6 min of hydrolysis reaction, the Al-5 wt%Hg-5 wt%NaCl can produce 971 mL g -1 hydrogen, higher than 917 mL g -1 hydrogen from Al-10 wt%Hg alloy. The Al-In-NaCl alloy has lower hydrolysis temperature about 10 K than that of Al-In alloy. Meanwhile, the reactivity of Al alloys can be improved or reduced via the additive metals. It can be found that the additive cadmium can reduce the reactivity of Al-Hg alloy. The Al-Hg-Cd alloys can keep good stability at the moist atmosphere below 343 K and have excellent hydrolysis performance around 343-373 K. The debased reactivity of Al-Hg-Cd composite comes from the formation of CdHg 2 compounds in the milling process. But the additive Zn and Ga doped into the Al-In-NaCl alloys can quickly increase the reactivity of the alloy which can quickly react with water at room temperature and have high hydrogen yield up to the theoretic value. Therefore, it is a promising possibility that the controllable reactivity of aluminum alloys can be obtained through the different additive according to the practical request, and the Al alloys can produce pure hydrogen for the fuel cell via the hydrolysis reaction.

Rapid detection of defects in fuel-cell electrodes using infrared reactive-flow-through technique

Science.gov (United States)

Das, Prodip K.; Weber, Adam Z.; Bender, Guido; Manak, Austin; Bittinat, Daniel; Herring, Andrew M.; Ulsh, Michael

2014-09-01

As fuel cells become more prominent, new manufacturing and production methods will need to be developed to deal efficiently and effectively with increased demand. One necessary component of this industrial growth is the accurate measurement of the variability in the manufacturing process. In this study, we present a diagnostic system that combines infrared thermography with a reactive-flow-through technique to detect catalyst-loading defects in fuel-cell gas-diffusion electrodes accurately with high spatial and temporal resolutions. Experimental results are compared with model predictions of thermal response with good agreement. Data analysis, operating-condition impacts, and detection limits are explored using both experiments and simulation. Overall, the results demonstrate the potential of this technique to measure defects on the millimeter length scale with temporal resolutions appropriate for use on a web-line. Thus we present the first development stage of a next-generation non-destructive diagnostic tool, which may be amenable to eventual use on roll-to-roll manufacturing lines.

Single-point reactive power control method on voltage rise mitigation in residential networks with high PV penetration

DEFF Research Database (Denmark)

Hasheminamin, Maryam; Agelidis, Vassilios; Ahmadi, Abdollah

2018-01-01

Voltage rise (VR) due to reverse power flow is an important obstacle for high integration of Photovoltaic (PV) into residential networks. This paper introduces and elaborates a novel methodology of an index-based single-point-reactive power-control (SPRPC) methodology to mitigate voltage rise by ...... system with high r/x ratio. Efficacy, effectiveness and cost study of SPRPC is compared to droop control to evaluate its advantages.......Voltage rise (VR) due to reverse power flow is an important obstacle for high integration of Photovoltaic (PV) into residential networks. This paper introduces and elaborates a novel methodology of an index-based single-point-reactive power-control (SPRPC) methodology to mitigate voltage rise...... by absorbing adequate reactive power from one selected point. The proposed index utilizes short circuit analysis to select the best point to apply this Volt/Var control method. SPRPC is supported technically and financially by distribution network operator that makes it cost effective, simple and efficient...

Loss Minimizing Operation of Doubly Fed Induction Generator Based Wind Generation Systems Considering Reactive Power Provision

DEFF Research Database (Denmark)

Baohua, Zhang; Hu, Weihao; Chen, Zhe

2014-01-01

The paper deals with control techniques for minimizing the operating loss of doubly fed induction generator based wind generation systems when providing reactive power. The proposed method achieves its goal through controlling the rotor side q-axis current in the synchronous reference frame...

The effect of aging on the dynamics of reactive and proactive cognitive control of response interference

Directory of Open Access Journals (Sweden)

Ling Xiang

2016-11-01

Full Text Available A prime-target interference task was used to investigate the effects of cognitive aging on reactive and proactive control in which frequency confounds and feature repetitions were eliminated from the cognitive control measures. We used distributional analyses to explore the dynamics of the two control functions by distinguishing the strength of incorrect response capture and the efficiency of suppression control. For reactive control, within-trial conflict control and between-trial conflict adaption were analyzed. The statistical analysis showed that there were no reliable between-trial conflict adaption effects for both young and older adults. For within-trial conflict control, the results revealed that older adults showed larger interference effects on mean RT and mean accuracy. Distributional analyses showed that the decline mainly stemmed from inefficient suppression rather than from stronger incorrect responses. For proactive control, older adults showed comparable proactive conflict resolution than young adults on mean RT and mean accuracy. Distributional analyses showed older adults were as effective as younger adults in adjusting their responses to minimize automatic response capture and actively suppress the direct response activation based on congruency proportion information. The results suggest that older adults were less proficient at suppressing interference after conflict was detected but can anticipate and prevent inference in response to congruency proportion manipulation. The results challenge earlier views that older adults have selective deficits in proactive control but are spared in reactive control.

A Hybrid Optimization Method for Reactive Power and Voltage Control Considering Power Loss Minimization

DEFF Research Database (Denmark)

Liu, Chengxi; Qin, Nan; Bak, Claus Leth

2015-01-01

This paper proposes a hybrid optimization method to optimally control the voltage and reactive power with minimum power loss in transmission grid. This approach is used for the Danish automatic voltage control (AVC) system which is typically a non-linear non-convex problem mixed with both...

Robust control technique for nuclear power plants

International Nuclear Information System (INIS)

Murphy, G.V.; Bailey, J.M.

1989-03-01

This report summarizes the linear quadratic Guassian (LQG) design technique with loop transfer recovery (LQG/LTR) for design of control systems. The concepts of return ratio, return difference, inverse return difference, and singular values are summarized. The LQG/LTR design technique allows the synthesis of a robust control system. To illustrate the LQG/LTR technique, a linearized model of a simple process has been chosen. The process has three state variables, one input, and one output. Three control system design methods are compared: LQG, LQG/LTR, and a proportional plus integral controller (PI). 7 refs., 20 figs., 6 tabs

Coordinated control of active and reactive power of distribution network with distributed PV cluster via model predictive control

Science.gov (United States)

Ji, Yu; Sheng, Wanxing; Jin, Wei; Wu, Ming; Liu, Haitao; Chen, Feng

2018-02-01

A coordinated optimal control method of active and reactive power of distribution network with distributed PV cluster based on model predictive control is proposed in this paper. The method divides the control process into long-time scale optimal control and short-time scale optimal control with multi-step optimization. The models are transformed into a second-order cone programming problem due to the non-convex and nonlinear of the optimal models which are hard to be solved. An improved IEEE 33-bus distribution network system is used to analyse the feasibility and the effectiveness of the proposed control method

Reactive Neural Control for Phototaxis and Obstacle Avoidance Behavior of Walking Machines

DEFF Research Database (Denmark)

Manoonpong, Poramate; Pasemann, Frank; Wörgötter, Florentin

2007-01-01

as a sensory fusion unit. It filters sensory noise and shapes sensory data to drive the corresponding reactive behavior. On the other hand, modular neural control based on a central pattern generator is applied for locomotion of walking machines. It coordinates leg movements and can generate omnidirectional...

Containment and Consensus-based Distributed Coordination Control for Voltage Bound and Reactive Power Sharing in AC Microgrid

DEFF Research Database (Denmark)

Han, Renke; Meng, Lexuan; Ferrari-Trecate, Giancarlo

2017-01-01

This paper offers a highly flexible and reliable control strategy to achieve voltage bounded regulation and accurate reactive power sharing coordinately in AC Micro-Grids. A containment and consensus-based distributed coordination controller is proposed, by which each output voltage magnitude can...... be bounded within a reasonable range and the accurate reactive power sharing among distributed generators can be also achieved. Combined with the two proposed controllers and electrical part of the AC Micro-Grid, a small signal model is fully developed to analyze the sensitivity of different control...... parameters. The effectiveness of the proposed controller in case of load variation, communication failure, plug-and-play capability are verified by the experimental setup as an islanded Micro-Grid....

Real-Time Control of Active and Reactive Power for Doubly Fed Induction Generator (DFIG-Based Wind Energy Conversion System

Directory of Open Access Journals (Sweden)

Aman Abdulla Tanvir

2015-09-01

Full Text Available This paper presents the modeling, rapid control prototyping, and hardware-in-the-loop testing for real-time simulation and control of a grid-connected doubly fed induction generator (DFIG in a laboratory-size wind turbine emulator for wind energy conversation systems. The generator is modeled using the direct-quadrature rotating reference frame circuit along with the aligned stator flux, and the field-oriented control approach is applied for independent control of the active and reactive power and the DC-link voltage at the grid side. The control of the active, reactive power and the DC-link voltage are performed using a back-to-back converter at sub- and super-synchronous as well as at variable speeds. The control strategy is experimentally validated on an emulated wind turbine driven by the Opal-RT real-time simulator (OP5600 for simultaneous control of the DC-link voltage, active and reactive power.

Reactivity estimation during a reactivity-initiated accident using the extended Kalman filter

International Nuclear Information System (INIS)

Busquim e Silva, R.; Marques, A.L.F.; Cruz, J.J.; Shirvan, K.; Kazimi, M.S.

2015-01-01

Highlights: • The EKF is modeled using sophisticate strategies to make the algorithm robust and accurate. • For a supercritical reactor under RIA, the EKF presents better results compared to IPK method independent of magnitude of the noise loads. • A sensitivity for five distinct carry-over effects indicates that the EKF is less sensitive to the different set of noise. • Although the P3D/R5 simulates the reactivity using a spatial kinetics method, the use of PKRE to model the EKF provides accurate results. • The reactivity’s standard deviation is higher for the IKF method. • Under HZP (slow power response) the IPK reactivity varies widely from positive to negative values (add extra difficulty to controlling the supercritical reactor): the EKF method does not have similar behavior under the same conditions (better controlling the operation). - Abstract: This study implements the extended Kalman filter (EKF) to estimate the nuclear reactor reactivity behavior under a reactivity-initiated accident (RIA). A coupled neutronics/thermal hydraulics code PARCS/RELAP5 (P3D/R5) simulates a control rod assembly ejection (CRE) on a traditional 2272 MWt PWR to generate the reactor power profile. A MATLAB script adds random noise to the simulated reactor power. For comparison, the inverse point kinetics (IPK) deterministic method is also implemented. Three different cases of CRE are simulated and the EKF, IPK and the P3D/R5 reactivity are compared. It was found that the EKF method presents better results compared to the IPK method. Furthermore, under a RIA due to small reactivity insertion and slow power response, the IPK reactivity varies widely from positive to negative, which may add extra difficulty to the task of controlling a supercritical reactor. This feature is also confirmed by a sensitivity analysis for five different noise loads and three distinct noise measurements standard deviations (SD)

Parametric study of a reactivity accident in a pressurized water reactor: control rod cluster ejection

International Nuclear Information System (INIS)

Chesnel, A.

1985-01-01

This research thesis concerns a class 4 accident in a PWR: the ejection of a control rod cluster from the reactor core. It aims at defining, for such an accident, the envelope values which relate the reactivity to the hot spot factor within the frame of a mode A control. The report describes the physical phenomena and their modelling during the considered transient. It presents a simple mathematical solution of the accident which shows that the main neutron parameters are the released reactivity, the delayed neutron fraction, the Doppler coefficient, and the hot spot factor. It reports a temperature sensitivity study, and discusses three-dimensional calculations of irradiation distributions

A new islanding detection technique for multiple mini hydro based on rate of change of reactive power and load connecting strategy

International Nuclear Information System (INIS)

Laghari, J.A.; Mokhlis, H.; Bakar, A.H.A.; Karimi, M.

2013-01-01

Highlights: • The requirement of DG interconnection with existing power system is discussed. • Various islanding detection techniques are discussed with their merits and demerits. • New islanding detection strategy is proposed for multiple mini hydro type DGs. • The proposed strategy is based on dq/dt and load connecting strategy. • The effectiveness of strategy is verified on various other cases. - Abstract: The interconnection of distributed generation (DG) into distribution networks is undergoing a rapid global expansion. It enhances the system’s reliability, while simultaneously reduces pollution problems related to the generation of electrical power. To fully utilize the benefits of DGs, certain technical issues need to be addressed. One of the most important issues in this context is islanding detection. This paper presents a new islanding detection technique that is suitable for multiple mini-hydro type DG units. The proposed strategy is based on the rate of change of reactive power and load connecting strategy to detect islanding within the system. For a large power mismatch, islanding is detected by rate of change of reactive power only. However, for a close power mismatch, the rate of change of reactive power initiates a load connecting strategy, which in turn alters the load on the distribution network. This load variation in the distribution network causes a variation in the rate of change of reactive power, which is utilized to distinguish islanding and other events. The simulation results show that the proposed strategy is effective in detecting islanding occurrence in a distribution network

Verifying Temporal Properties of Reactive Systems by Transformation

OpenAIRE

Hamilton, Geoff

2015-01-01

We show how program transformation techniques can be used for the verification of both safety and liveness properties of reactive systems. In particular, we show how the program transformation technique distillation can be used to transform reactive systems specified in a functional language into a simplified form that can subsequently be analysed to verify temporal properties of the systems. Example systems which are intended to model mutual exclusion are analysed using these techniques with...

Coupling/Tradeoff Analysis and Novel Containment Control for Reactive Power, Output Voltage in Islanded Micro-Grid

DEFF Research Database (Denmark)

Han, Renke; Meng, Lexuan; Guerrero, Josep M.

2016-01-01

Based on the hierarchical control structure in islanded Micro-Grid (MG) systems, the coupling/tradeoff effects in different control levels are analyzed in details. In the primary level, analyses of the coupling effects among droop control gains, line impedance differences, output reactive power...

Determination of the phthalocyanine textile dye, reactive turquoise blue, by electrochemical techniques

Directory of Open Access Journals (Sweden)

Osugi Marly E.

2003-01-01

Full Text Available Turquoise blue 15 (AT15 is a reactive dye widely used in the textile industry to color natural fibers. The presence of these dyes in effluent and industrial wastewater is of considerable interest due ecotoxicological and environmental problems. The electrochemical reduction of this dye has been investigated in aqueous solution using cyclic voltammetry, controlled potential electrolysis and cathodic stripping voltammetry. Optimum conditions for dye discoloration by controlled potential electrolysis use an alkaline medium. Using cathodic stripping voltammetry a linear calibration graph was obtained from 5.00x10-8 mol L-1 to 1.00x10-6 mol L-1 of AT15 at pH 4.0, using accumulation times of 180 and 240 s and an accumulation potential of 0.0 V. The proposed method was applied in direct determination of the dye in tap water and in textile industry effluent.

Reactive Power Control for Improving Wind Turbine System Behavior Under Grid Faults

DEFF Research Database (Denmark)

Rodriguez, P.; Timbus, A.; Teodorescu, Remus

2009-01-01

This letter aims to present a generalized vector-based formulation for calculating the grid-side current reference to control reactive power delivered to the grid. Strategies for current reference generation were implemented on the abc stationary reference frame, and their effectivenesswas...... demonstrated experimentally, perhaps validating the theoretical analysis even under grid fault conditions....

Coordinated Volt/Var Control in Distribution Systems with Distributed Generations Based on Joint Active and Reactive Powers Dispatch

Directory of Open Access Journals (Sweden)

Abouzar Samimi

2016-01-01

Full Text Available One of the most significant control schemes in optimal operation of distribution networks is Volt/Var control (VVC. Owing to the radial structure of distribution systems and distribution lines with a small X/R ratio, the active power scheduling affects the VVC issue. A Distribution System Operator (DSO procures its active and reactive power requirements from Distributed Generations (DGs along with the wholesale electricity market. This paper proposes a new operational scheduling method based on a joint day-ahead active/reactive power market at the distribution level. To this end, based on the capability curve, a generic reactive power cost model for DGs is developed. The joint active/reactive power dispatch model presented in this paper motivates DGs to actively participate not only in the energy markets, but also in the VVC scheme through a competitive market. The proposed method which will be performed in an offline manner aims to optimally determine (i the scheduled active and reactive power values of generation units; (ii reactive power values of switched capacitor banks; and (iii tap positions of transformers for the next day. The joint active/reactive power dispatch model for daily VVC is modeled in GAMS and solved with the DICOPT solver. Finally, the plausibility of the proposed scheduling framework is examined on a typical 22-bus distribution test network over a 24-h period.

Optimal Design for Reactivity Ratio Estimation: A Comparison of Techniques for AMPS/Acrylamide and AMPS/Acrylic Acid Copolymerizations

Directory of Open Access Journals (Sweden)

Alison J. Scott

2015-11-01

Full Text Available Water-soluble polymers of acrylamide (AAm and acrylic acid (AAc have significant potential in enhanced oil recovery, as well as in other specialty applications. To improve the shear strength of the polymer, a third comonomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS, can be added to the pre-polymerization mixture. Copolymerization kinetics of AAm/AAc are well studied, but little is known about the other comonomer pairs (AMPS/AAm and AMPS/AAc. Hence, reactivity ratios for AMPS/AAm and AMPS/AAc copolymerization must be established first. A key aspect in the estimation of reliable reactivity ratios is design of experiments, which minimizes the number of experiments and provides increased information content (resulting in more precise parameter estimates. However, design of experiments is hardly ever used during copolymerization parameter estimation schemes. In the current work, copolymerization experiments for both AMPS/AAm and AMPS/AAc are designed using two optimal techniques (Tidwell-Mortimer and the error-in-variables-model (EVM. From these optimally designed experiments, accurate reactivity ratio estimates are determined for AMPS/AAm (rAMPS = 0.18, rAAm = 0.85 and AMPS/AAc (rAMPS = 0.19, rAAc = 0.86.

Soft sensor based composition estimation and controller design for an ideal reactive distillation column.

Science.gov (United States)

Vijaya Raghavan, S R; Radhakrishnan, T K; Srinivasan, K

2011-01-01

In this research work, the authors have presented the design and implementation of a recurrent neural network (RNN) based inferential state estimation scheme for an ideal reactive distillation column. Decentralized PI controllers are designed and implemented. The reactive distillation process is controlled by controlling the composition which has been estimated from the available temperature measurements using a type of RNN called Time Delayed Neural Network (TDNN). The performance of the RNN based state estimation scheme under both open loop and closed loop have been compared with a standard Extended Kalman filter (EKF) and a Feed forward Neural Network (FNN). The online training/correction has been done for both RNN and FNN schemes for every ten minutes whenever new un-trained measurements are available from a conventional composition analyzer. The performance of RNN shows better state estimation capability as compared to other state estimation schemes in terms of qualitative and quantitative performance indices. Copyright © 2010 ISA. Published by Elsevier Ltd. All rights reserved.

Consensus-based Distributed Control for Accurate Reactive, Harmonic and Imbalance Power Sharing in Microgrids

DEFF Research Database (Denmark)

Zhou, Jianguo; Kim, Sunghyok; Zhang, Huaguang

2018-01-01

This paper investigates the issue of accurate reactive, harmonic and imbalance power sharing in a microgrid. Harmonic and imbalance droop controllers are developed to proportionally share the harmonic power and the imbalance power among distributed generation (DG) units and improve the voltage...... voltage. With the proposed methods, the microgrid system reliability and flexibility can be enhanced and the knowledge of the line impedance is not required. And the reactive, harmonic and imbalance power can be proportionally shared among the DG units. Moreover, the quality of the voltage at PCC can...

Calculation-measurement comparison for control rods reactivity in RA-3 nuclear reactor

International Nuclear Information System (INIS)

Estryk, Guillermo; Gomez, Angel

2002-01-01

The RA-3 Nuclear Reactor of the Atomic Energy National Commission from Argentina, begun working with high enrichment fuel elements in 1967, and turned to low enrichment by 1990. During 1999 it was found out that several fuel elements had problems, so more than 50 % of them had to be removed from the core. Because of this, it was planned to go from core 93 to core 94 with special care from nuclear safety point of view. Core 94 was preceded by other five, T-1 to T-5, only as transitory ones. The care implied several nuclear parameters measurements: core reactivity excess, calibration of control rods, etc. Calculations were performed afterwards to simulate those measurements using the neutron diffusion code PUMA. The comparison shows a good agreement for more than 80% of the cases with differences lower than 10% in reactivity. The greatest differences were found in the last part of the control rods calibration and a better calculation of cell constants is planned to be done in order to improve the adjustment. (author)

Trends vs. reactor size of passive reactivity shutdown and control performance

International Nuclear Information System (INIS)

Wade, D.C.; Fujita, E.K.

1987-01-01

For LMR concepts, the goal of passive reactivity shutdown has been approached in the US by designing the reactors for favorable relationships among the power, power/flow, and inlet temperature coefficients of reactivity, for high internal conversion ratio (yielding small burnup control swing), and for a primary pump coastdown time appropriately matched to the delayed neutron hold back of power decay upon negative reactivity input. The use of sodium bonded metallic fuel pins has facilitated the achievement of the massive shutdown design goals as a consequence of their high thermal conductivity and high effective heavy metal density. Alternately, core designs based on derated oxide pins may be able to achieve the passive shutdown features at the cost of larger core volume and increased initial fissile inventory. For LMR concepts, the passive decay heat removal goal of inherent safety has been approached in US designs by use of pool layouts, larger surface to volume ratio of the reactor vessel with natural draft air cooling of the vessel surface, elevations and redans which promote natural circulation through the core, and thermal mass of the pool contents sufficient to absorb that initial transient decay heat which exceeds the natural draft air cooling capacity. This paper describes current US ''inherently safe'' reactor design

Systematic Integrated Process Design and Control of Reactive Distillation Processes Involving Multi-elements

DEFF Research Database (Denmark)

Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

2016-01-01

driving force approach. Next, through analytical, steady-state and closed-loop dynamic analysis it is verified that the control structure, disturbance rejection and energy requirement of the reactive distillation column is better than any other operation point that is not at the maximum driving force...

Substation Reactive Power Regulation Strategy

Science.gov (United States)

Zhang, Junfeng; Zhang, Chunwang; Ma, Daqing

2018-01-01

With the increasing requirements on the power supply quality and reliability of distribution network, voltage and reactive power regulation of substations has become one of the indispensable ways to ensure voltage quality and reactive power balance and to improve the economy and reliability of distribution network. Therefore, it is a general concern of the current power workers and operators that what kind of flexible and effective control method should be used to adjust the on-load tap-changer (OLTC) transformer and shunt compensation capacitor in a substation to achieve reactive power balance in situ, improve voltage pass rate, increase power factor and reduce active power loss. In this paper, based on the traditional nine-zone diagram and combining with the characteristics of substation, a fuzzy variable-center nine-zone diagram control method is proposed and used to make a comprehensive regulation of substation voltage and reactive power. Through the calculation and simulation of the example, this method is proved to have satisfactorily reconciled the contradiction between reactive power and voltage in real-time control and achieved the basic goal of real-time control of the substation, providing a reference value to the practical application of the substation real-time control method.

Development of an alternative reactivity meter for nuclear reactor control

International Nuclear Information System (INIS)

Ferreira, P.S.B.

1991-01-01

This work describes an alternative version of the IPEN-CNEN/SP reactivity-meter. This new version utilizes a programmable electrometer (to realize the data acquisition) and a IBM-PC microcomputer to process the reactivity calculation. The aim of development of this alternative reactivity-meter is to have available a equipment of measurements of reactivity in the case of the later version show any problem during an experiment. (author)

Reduction of DC-link Capacitor in Case of Cascade Multilevel Converters by means of Reactive Power Control

DEFF Research Database (Denmark)

Gohil, Ghanshyamsinh Vijaysinh; Wang, Huai; Liserre, Marco

2014-01-01

A method to selectively control the amount of dc link voltage ripple by processing desired reactive power by a DC/DC converter in isolated AC/DC or AC/DC/AC system is proposed. The concept can reduce the dc link capacitors used for balancing the input and output power and thereby limiting...... the voltage ripple. It allows the use of smaller dc link capacitor and hence a longer lifetime and at the same time high power density and low cost can be achieved. The isolated DC/DC converter is controlled to process the desired reactive power in addition to the active power. The control system to achieve...

Control of Reactive Species Generated by Low-frequency Biased Nanosecond Pulse Discharge in Atmospheric Pressure Plasma Effluent

Science.gov (United States)

Takashima, Keisuke; Kaneko, Toshiro

2016-09-01

The control of hydroxyl radical and the other gas phase species generation in the ejected gas through air plasma (air plasma effluent) has been experimentally studied, which is a key to extend the range of plasma treatment. Nanosecond pulse discharge is known to produce high reduced electric field (E/N) discharge that leads to efficient generation of the reactive species than conventional low frequency discharge, while the charge-voltage cycle in the low frequency discharge is known to be well-controlled. In this study, the nanosecond pulse discharge biased with AC low frequency high voltage is used to take advantages of these discharges, which allows us to modulate the reactive species composition in the air plasma effluent. The utilization of the gas-liquid interface and the liquid phase chemical reactions between the modulated long-lived reactive species delivered from the air plasma effluent could realize efficient liquid phase chemical reactions leading to short-lived reactive species production far from the air plasma, which is crucial for some plasma agricultural applications.

Thiol-ene thermosets exploiting surface reactivity for layer-by-layer structures and control of penetration depth for selective surface reactivity

DEFF Research Database (Denmark)

Daugaard, Anders Egede; Westh, Andreas; Pereira Rosinha Grundtvig, Ines

Thiol-ene thermosets have been shown to be an efficient platform for preparation of functional polymer surfaces. Especially the effectiveness and versatility of the system has enabled a large variety of network properties to be obtained in a simple and straight-forward way. Due to its selectivity......, various thiols and allyl or other vinyl reactants can be used to obtain either soft and flexible1 or more rigid functional thermosets 2. The methodology permits use of etiher thermal or photochemical conditions both for matrix preparation as well as for surface functionalization. Due to excess reactive...... groups in thµe surface of thiol-ene thermosets, it is possible to prepare surface functional thermosets or to exploit the reactive groups for modular construction and subsequent chemical bonding. Here a different approach preparing monolithic layer-by-layer structures with controlled mechanical...

Application of the Modified Source Multiplication (MSM) technique to subcritical reactivity worth measurements in thermal and fast reactor systems

International Nuclear Information System (INIS)

Blaise, P.; Fougeras, P.; Mellier, F.

2009-01-01

The Amplified Source Multiplication (ASM) method and its improved Modified Source Multiplication (MSM) method have been widely used in the CEA's EOLE and MASURCA critical facilities over the past decades for the determination of reactivity worths by using fission chambers in subcritical configurations. They have been successfully applied to absorber (single or clusters) worth measurement in both thermal and fast spectra, or for (sodium or water) void reactivity worths. The ASM methodology, which is the basic technique to estimate a reactivity worth, uses relatively simple relationships between count rates of efficient miniature fission chambers located in slightly subcritical reference and perturbed configurations. If this method works quite well for small reactivity variation (a few effective delayed neutron fraction), its raw results needs to be corrected to take into account the flux perturbation in the fission chamber. This is performed by applying to the measurement a correction factor called MSM. Its characteristics is to take into account the local space and energy variation of the spectrum in the fission chamber, through standard perturbation theory applied to neutron transport calculation in the perturbed configuration. The proposed paper describes in details both methodologies, with their associated uncertainties. Applications on absorber cluster worth in the MISTRAL-4 full MOX mock-up core and the last core loaded in MASURCA show the importance of the MSM correction on raw data. (authors)

SULEU NTP Core with Passive Reactivity Control and Enhanced Submersion Safety

Energy Technology Data Exchange (ETDEWEB)

Venneri, Paolo; Kim, Yong Hee [KAIST, Daejeon (Korea, Republic of); Eades, Michael J [The Ohio State University, Ohio (United States)

2016-05-15

In this summary, SULEU has been adapted to implement some of the latest developments of LEUNTP design efforts. These include the implementation of a rapid depletion burnable absorber to flatten the reactivity profile during operation and the addition of a lower axial reflector to help minimize the reactivity increase during the full submersion criticality accident. The purpose of this study is to show the state of current LEU-NTP designs in terms of resolving key issues such as minimizing control drum usage and resolving the full submersion criticality accident. Future work will include integrating the rapid depletion poison with other passive reactivity control devices (such as hydrogen density in the tie-tubes) and developing additional systems for mitigating the full submersion criticality accident. It is widely acknowledged that nuclear thermal propulsion (NTP) is an enabling technology for manned missions to Mars and other locations beyond low-Earth orbit. Without nuclear thermal propulsion, manned space travel will be severely limited by the propellant requirements of chemical propulsion and significantly longer travel times of electric propulsion. While the performance superiority of NTP is clear, its implementation has been to date unsuccessful due to the significant costs of development, implementation, and regulations associated with the heritage NTP designs. These new systems take heritage designs and experimental results and adapt them to use LEU fuel with minimum impact on the heritage system. This is done in order to ensure their continued relevance with existing NTP research efforts and enable their rapid implementation into existing NASA efforts for human Mars mission planning. Of the current baseline NTP designs being studied, this paper concerns itself with the improvement of the Superb Use of Low Enriched (SULEU) core.

Use of nuclear techniques in biological control

International Nuclear Information System (INIS)

Greany, Patrick D.; Carpenter, James E.

2000-01-01

As pointed out by Benbrook (1996), pest management is at a crossroads, and there is a great need for new, biointensive pest management strategies. Among these approaches, biological control is a keystone. However, because of increasing concerns about the introduction of exotic natural enemies of insect pests and weeds (Howarth 1991, Delfosse 1997), the overall thrust of biological control has moved toward augmentative biological control, involving releases of established natural enemy species (Knipling 1992). This in turn has created a need to develop more cost-effective mass rearing technologies for beneficial insects. Nuclear techniques could play an especially important role in augmentative biological control, not only in facilitating mass rearing, but in several other ways, as indicated below. Recognising the potential value for use of nuclear techniques in biological control, the Insect and Pest Control Section of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, International Atomic Energy Agency, sponsored a Consultants' Group Meeting on this subject in April 1997. The Group produced a document entitled Use of Nuclear Techniques in Biological Control: Managing Pests, Facilitating Trade and Protecting the Environment. The consultants included the authors of this paper as well as Ernest Delfosse (at that time, with the USDA-APHIS National Biological Control Institute), Garry Hill (Intl. Institute for Biological Control), Sinthya Penn (Beneficial Insectary), and Felipe Jeronimo (USDA-APHIS PPQ, Guatemala). The remarks presented in this paper reflect the thoughts presented by these consultants and other participants at the IAEA-sponsored meeting. Several potential uses for nuclear techniques were identified by the Consultants' Group, including: 1) improvements in rearing media (either artificial diets or natural hosts/prey), 2) provision of sterilised natural prey to be used as food during shipment, to ameliorate concerns relating to the

Effects of intensive glucose control on platelet reactivity in patients with acute coronary syndromes. Results of the CHIPS Study ("Control de Hiperglucemia y Actividad Plaquetaria en Pacientes con Sindrome Coronario Agudo").

Science.gov (United States)

Vivas, David; García-Rubira, Juan C; Bernardo, Esther; Angiolillo, Dominick J; Martín, Patricia; Calle-Pascual, Alfonso; Núñez-Gil, Iván; Macaya, Carlos; Fernández-Ortiz, Antonio

2011-05-01

Hyperglycaemia has been associated with increased platelet reactivity and impaired prognosis in patients with acute coronary syndrome (ACS). Whether platelet reactivity can be reduced by lowering glucose in this setting is unknown. The aim of this study was to assess the functional impact of intensive glucose control with insulin on platelet reactivity in patients admitted with ACS and hyperglycaemia. This is a prospective, randomised trial evaluating the effects of either intensive glucose control (target glucose 80-120 mg/dl) or conventional control (target glucose 180 mg/dl or less) with insulin on platelet reactivity in patients with ACS and hyperglycaemia. The primary endpoint was platelet aggregation following stimuli with 20 μM ADP at 24 h and at hospital discharge. Aggregation following collagen, epinephrine and thrombin receptor-activated peptide, as well as P2Y₁₂ reactivity index and surface expression of glycoprotein IIb/IIIa and P-selectin were also measured. Of the 115 patients who underwent random assignment, 59 were assigned to intensive and 56 to conventional glucose control. Baseline platelet functions and inhospital management were similar in both groups. Maximal aggregation after ADP stimulation at hospital discharge was lower in the intensive group (47.9 ± 13.2% vs 59.1 ± 17.3%; p=0.002), whereas no differences were found at 24 h. Similarly all other parameters of platelet reactivity measured at hospital discharge were significantly reduced in the intensive glucose control group. In this randomised trial, early intensive glucose control with insulin in patients with ACS presenting with hyperglycaemia was found to decrease platelet reactivity. Clinical Trial Registration Number http://www.controlledtrials.com/ISRCTN35708451/ISRCTN35708451.

A Hierarchical Control Scheme for Reactive Power and Harmonic Current Sharing in Islanded Microgrids

DEFF Research Database (Denmark)

Lorzadeh, Iman; Firoozabadi, Mehdi Savaghebi; Askarian Abyaneh, Hossein

2015-01-01

In this paper, a hierarchical control scheme consisting of primary and secondary levels is proposed for achieving accurate reactive power and harmonic currents sharing among interface inverters of distributed generators (DGs) in islanded microgrids. Firstly, fundamental and main harmonic componen...

Trends vs. reactor size of passive reactivity shutdown and control performance

International Nuclear Information System (INIS)

Wade, D.C.; Fujita, E.K.

1988-01-01

The focus of the US advanced reactor program since the cancellation of CRBR has been on inherent safety and cost reduction. The notion is to so design the reactor that in the event of an off normal condition, it brings itself to a safe shutdown condition and removes decay heat by reliance on ''inherent processes'' i.e., without reliance on devices requiring switching and outside sources of power. Such a reactor design would offer the potential to eliminate costly ''Engineered Safety Features,'' to lower capital costs, and to assuage public unease concerning reactor safety. For LMR concepts, the goal of passive reactivity shutdown has been approached in the US by designing the reactors for favorable relationships among the power, power/flow, and inlet temperature coefficients of reactivity, for high internal conversion ratio (yielding small burnup control swing), and for a primary pump coastdown time appropriately matched to the delayed neutron hold back of power decay upon negative reactivity input. The use of sodium bonded metallic fuel pins has facilitated the achievement of the passive shutdown design goals as a consequence of their high thermal conductivity and high effective heavy metal density. Alternately, core designs based on derated oxide pins may be able to achieve the passive shutdown features at the cost of larger core volume and increased initial fissile inventory. 8 refs., 12 figs., 1 tab

Development of a digital reactivity meter for criticality prediction and control rod worth evaluation in pressurized water reactors

Energy Technology Data Exchange (ETDEWEB)

Kuramoto, Renato Y.R.; Miranda, Anselmo F.; Valladares, Gastao Lommez; Prado, Adelk C. [Eletrobras Termonuclear S.A. - ELETRONUCLEAR, Angra dos Reis, RJ (Brazil). Central Nuclear Almirante Alvaro Alberto], e-mail: kuramot@eletronuclear.gov.br

2009-07-01

In this work, we have proposed the development of a digital reactivity meter in order to monitor subcriticality continuously during criticality approach in a PWR. A subcritical reactivity meter can provide an easy prediction of the estimated critical point prior to reactor criticality, without complicated hand calculation. Moreover, in order to reduce the interval of the Physics Tests from the economical point of view, a subcritical reactivity meter can evaluate the control rod worth from direct subcriticality measurement. In other words, count rate of Source Range (SR) detector recorded during the criticality approach could be used for subcriticality evaluation or control rod worth evaluation. Basically, a digital reactivity meter is based on the inverse solution of the kinetic equations of a reactor with the external neutron source in one-point reactor model. There are some difficulties in the direct application of a digital reactivity meter to the subcriticality measurement. When the Inverse Kinetic method is applied to a sufficiently high power level or to a core without an external neutron source, the neutron source term may be neglected. When applied to a lower power level or in the sub-critical domain, however, the source effects must be taken in account. Furthermore, some treatments are needed in using the count rate of Source Range (SR) detector as input signal to the digital reactivity meter. To overcome these difficulties, we have proposed a digital reactivity meter combined with a methodology of the modified Neutron Source Multiplication (NSM) method with correction factors for subcriticality measurements in PWR. (author)

Development of a digital reactivity meter for criticality prediction and control rod worth evaluation in pressurized water reactors

International Nuclear Information System (INIS)

Kuramoto, Renato Y.R.; Miranda, Anselmo F.; Valladares, Gastao Lommez; Prado, Adelk C.

2009-01-01

In this work, we have proposed the development of a digital reactivity meter in order to monitor subcriticality continuously during criticality approach in a PWR. A subcritical reactivity meter can provide an easy prediction of the estimated critical point prior to reactor criticality, without complicated hand calculation. Moreover, in order to reduce the interval of the Physics Tests from the economical point of view, a subcritical reactivity meter can evaluate the control rod worth from direct subcriticality measurement. In other words, count rate of Source Range (SR) detector recorded during the criticality approach could be used for subcriticality evaluation or control rod worth evaluation. Basically, a digital reactivity meter is based on the inverse solution of the kinetic equations of a reactor with the external neutron source in one-point reactor model. There are some difficulties in the direct application of a digital reactivity meter to the subcriticality measurement. When the Inverse Kinetic method is applied to a sufficiently high power level or to a core without an external neutron source, the neutron source term may be neglected. When applied to a lower power level or in the sub-critical domain, however, the source effects must be taken in account. Furthermore, some treatments are needed in using the count rate of Source Range (SR) detector as input signal to the digital reactivity meter. To overcome these difficulties, we have proposed a digital reactivity meter combined with a methodology of the modified Neutron Source Multiplication (NSM) method with correction factors for subcriticality measurements in PWR. (author)

Reactive Arthritis

Directory of Open Access Journals (Sweden)

Eren Erken

2013-06-01

Full Text Available Reactive arthritis is an acute, sterile, non-suppurative and inflammatory arthropaty which has occured as a result of an infectious processes, mostly after gastrointestinal and genitourinary tract infections. Reiter syndrome is a frequent type of reactive arthritis. Both reactive arthritis and Reiter syndrome belong to the group of seronegative spondyloarthropathies, associated with HLA-B27 positivity and characterized by ongoing inflammation after an infectious episode. The classical triad of Reiter syndrome is defined as arthritis, conjuctivitis and urethritis and is seen only in one third of patients with Reiter syndrome. Recently, seronegative asymmetric arthritis and typical extraarticular involvement are thought to be adequate for the diagnosis. However, there is no established criteria for the diagnosis of reactive arthritis and the number of randomized and controlled studies about the therapy is not enough. [Archives Medical Review Journal 2013; 22(3.000: 283-299

Active structural control with stable fuzzy PID techniques

CERN Document Server

Yu, Wen

2016-01-01

This book presents a detailed discussion of intelligent techniques to measure the displacement of buildings when they are subjected to vibration. It shows how these techniques are used to control active devices that can reduce vibration 60–80% more effectively than widely used passive anti-seismic systems. After introducing various structural control devices and building-modeling and active structural control methods, the authors propose offset cancellation and high-pass filtering techniques to solve some common problems of building-displacement measurement using accelerometers. The most popular control algorithms in industrial settings, PD/PID controllers, are then analyzed and then combined with fuzzy compensation. The stability of this combination is proven with standard weight-training algorithms. These conditions provide explicit methods for selecting PD/PID controllers. Finally, fuzzy-logic and sliding-mode control are applied to the control of wind-induced vibration. The methods described are support...

Comprehensive Cost Minimization in Distribution Networks Using Segmented-time Feeder Reconfiguration and Reactive Power Control of Distributed Generators

DEFF Research Database (Denmark)

Chen, Shuheng; Hu, Weihao; Chen, Zhe

2016-01-01

In this paper, an efficient methodology is proposed to deal with segmented-time reconfiguration problem of distribution networks coupled with segmented-time reactive power control of distributed generators. The target is to find the optimal dispatching schedule of all controllable switches...... and distributed generators’ reactive powers in order to minimize comprehensive cost. Corresponding constraints, including voltage profile, maximum allowable daily switching operation numbers (MADSON), reactive power limits, and so on, are considered. The strategy of grouping branches is used to simplify...... (FAHPSO) is implemented in VC++ 6.0 program language. A modified version of the typical 70-node distribution network and several real distribution networks are used to test the performance of the proposed method. Numerical results show that the proposed methodology is an efficient method for comprehensive...

State and data techniques for control of discontinuous systems

International Nuclear Information System (INIS)

Kisner, R.A.

1986-01-01

This paper describes a technique for structured analysis and design of automated control systems. The technique integrates control of continuous and discontinuous nuclear power plant subsystems and components. A hierarchical control system with distributed intelligence follows from applying the technique. Further, it can be applied to all phases of control system design. For simplicity, the example used in the paper is limited to phase 1 design (basic automatic control action), in which no maintenance, testing, or contingency capability is attempted. 11 figs

BN600 reactivity definition

International Nuclear Information System (INIS)

Zheltyshev, V.; Ivanov, A.

2000-01-01

Since 1980, the fast BN600 reactor with sodium coolant has been operated at Beloyarsk Nuclear Power Plant. The periodic monitoring of the reactivity modifications should be implemented in compliance with the standards and regulations applied in nuclear power engineering. The reactivity measurements are carried out in order to confirm the basic neutronic features of a BN600 reactor. The reactivity measurements are aimed to justify that nuclear safety is provided in course of the in-reactor installation of the experimental core components. Two reactivity meters are to be used on BN600 operation: 1. Digital on-line reactivity calculated under stationary reactor operation on power (approximation of the point-wise kinetics is applied). 2. Second reactivity meter used to define the reactor control rod operating components efficiency under reactor startup and take account of the changing efficiency of the sensor, however, this is more time-consumptive than the on-line reactivity meter. The application of two reactivity meters allows for the monitoring of the reactor reactivity under every operating mode. (authors)

Reactive Power Control of Single-Stage Three-Phase Photovoltaic System during Grid Faults Using Recurrent Fuzzy Cerebellar Model Articulation Neural Network

Directory of Open Access Journals (Sweden)

Faa-Jeng Lin

2014-01-01

Full Text Available This study presents a new active and reactive power control scheme for a single-stage three-phase grid-connected photovoltaic (PV system during grid faults. The presented PV system utilizes a single-stage three-phase current-controlled voltage-source inverter to achieve the maximum power point tracking (MPPT control of the PV panel with the function of low voltage ride through (LVRT. Moreover, a formula based on positive sequence voltage for evaluating the percentage of voltage sag is derived to determine the ratio of the injected reactive current to satisfy the LVRT regulations. To reduce the risk of overcurrent during LVRT operation, a current limit is predefined for the injection of reactive current. Furthermore, the control of active and reactive power is designed using a two-dimensional recurrent fuzzy cerebellar model articulation neural network (2D-RFCMANN. In addition, the online learning laws of 2D-RFCMANN are derived according to gradient descent method with varied learning-rate coefficients for network parameters to assure the convergence of the tracking error. Finally, some experimental tests are realized to validate the effectiveness of the proposed control scheme.

Determination of the most reactivity control rod by pseudo-harmonics perturbation method; Determinacao da barra de controle mais reativa usando o metodo de pseudo-harmonicos

Energy Technology Data Exchange (ETDEWEB)

Freire, Fernando S.; Silva, Fernando C.; Martinez, Aquilino S. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear]. E-mail: ffreire@con.ufrj.br; fernando@con.ufrj.br; aquilino@.con.ufrj.br

2005-07-01

Frequently it is necessary to compute the change in core multiplication caused by a change in the core temperature or composition. Even when this perturbation is localized, such as a control rod inserted into the core, one does not have to repeat the original criticality calculation, but instead we can use the well-known pseudo-harmonics perturbation method to express the corresponding change in the multiplication factor in terms of the neutron flux expanded in the basis vectors characterizing the unperturbed core. Therefore we may compute the control rod worth to find the most reactivity control rod to calculate the fast shutdown margin. In this thesis we propose a simple and precise method to identify the most reactivity control rod. (author)

Context-dependent switching between proactive and reactive working memory control mechanisms in the right inferior frontal gyrus.

Science.gov (United States)

Marklund, Petter; Persson, Jonas

2012-11-15

A critical feature of higher cognitive functioning is the capacity to flexibly tailor information processing and behaviors to current situational demands. Recent neurocognitive models have been postulated to account for the dynamic nature of human executive processing by invoking two dissociable cognitive control modes, proactive and reactive control. These may involve partially overlapping, but temporally distinct neural implementation in the prefrontal cortex. Prior brain imaging studies exploring proactive control have mainly used tasks requiring only information about single-items to be retained over unfilled delays. Whether proactive control can also be utilized to facilitate performance in more complex working memory tasks, in which concurrent processing of intervening items and updating is mandatory during contextual cue maintenance remains an open question. To examine this issue and to elucidate the extent to which overlapping neural substrates underlie proactive and reactive control we used fMRI and a modified verbal 3-back paradigm with embedded cues predictive of high-interference trials. This task requires context information to be retained over multiple intervening trials. We found that performance improved with item-specific cues predicting forthcoming lures despite increased working memory load. Temporal dynamics of activation in the right inferior frontal gyrus suggest flexible switching between proactive and reactive control in a context-dependent fashion, with greater sustained responses elicited in the 3-back task involving context maintenance of cue information and greater transient responses elicited in the 3-back task absent of cues. Copyright © 2012 Elsevier Inc. All rights reserved.

Reactive power control of wind farm using facts devices

International Nuclear Information System (INIS)

Ashfaq, S.; Arif, A.; Shakeel, A.; Mahmood, T.

2014-01-01

Wind energy is an attainable option to complement other types of pollution-free green generation Grid connections of renewable energy resources are vital if they are to be effectively exploited, but grid connection brings problems of voltage fluctuation and harmonic distortion. FACTs devices are one of the power electronics revolutions to improve voltage profile, system stability, and reactive power control and to reduce transmission losses. The studied system here is a variable speed wind generation system based on Induction Generator (IG) with integration of different FACTs controllers in the wind farm. To harness the wind power efficiently the most reliable and expensive system in the present era is grid connected doubly fed induction generator. Induction generator with FACTs devices is a suitable economical replacement. The suggested scheme is implemented in MATLAB Simulink with real time parameters of GHARO wind power plant in Sind, and corresponding results and output waveforms proves the potential strength of proposed methodology. (author)

Is blunted cardiovascular reactivity in depression mood-state dependent? A comparison of major depressive disorder remitted depression and healthy controls.

Science.gov (United States)

Salomon, Kristen; Bylsma, Lauren M; White, Kristi E; Panaite, Vanessa; Rottenberg, Jonathan

2013-10-01

Prior work has repeatedly demonstrated that people who have current major depression exhibit blunted cardiovascular reactivity to acute stressors (e.g., Salomon et al., 2009). A key question regards the psychobiological basis for these deficits, including whether such deficits are depressed mood-state dependent or whether these effects are trait-like and are observed outside of depression episodes in vulnerable individuals. To examine this issue, we assessed cardiovascular reactivity to a speech stressor task and a forehead cold pressor in 50 individuals with current major depressive disorder (MDD), 25 with remitted major depression (RMD), and 45 healthy controls. Heart rate (HR), blood pressure and impedance cardiography were assessed and analyses controlled for BMI and sex. Significant group effects were found for SBP, HR, and PEP for the speech preparation period and HR, CO, and PEP during the speech. For each of these parameters, only the MDD group exhibited attenuated reactivity as well as impaired SBP recovery. Reactivity and recovery in the RMD group more closely resembled the healthy controls. Speeches given by the MDD group were rated as less persuasive than the RMD or healthy controls' speeches. No significant differences were found for the cold pressor. Blunted cardiovascular reactivity and impaired recovery in current major depression may be mood-state dependent phenomena and may be more reflective of motivational deficits than deficits in the physiological integrity of the cardiovascular system. Copyright © 2013 Elsevier B.V. All rights reserved.

Establishment of analysis procedure for control rod reactivity worth

Energy Technology Data Exchange (ETDEWEB)

Song, Hoon; Kim, Young Il; Kim, Sang Ji; Kim, Young In

2001-03-01

As to the calculation method of control rod reactivity relating to hexagonal assembly, which are used generally in fast reactor, we have investigated the calculation method, the problems to rise during calculation, the degrees of calculation and the enhancement of calculation modeling so on, and estimated the application of calculation method through comparison and analysis of calculation result using the effective cross section generation system, TRANSX/TWODANT, and neutron flux calculation system, diffusion theory code DIF-3D, which are belonged to K-CORE System, and determined the basic calculation method, and extracted the present calculation problem in case of application in K-CORE System and the future improvement items so on.

Establishment of analysis procedure for control rod reactivity worth

International Nuclear Information System (INIS)

Song, Hoon; Kim, Young Il; Kim, Sang Ji; Kim, Young In

2001-03-01

As to the calculation method of control rod reactivity relating to hexagonal assembly, which are used generally in fast reactor, we have investigated the calculation method, the problems to rise during calculation, the degrees of calculation and the enhancement of calculation modeling so on, and estimated the application of calculation method through comparison and analysis of calculation result using the effective cross section generation system, TRANSX/TWODANT, and neutron flux calculation system, diffusion theory code DIF-3D, which are belonged to K-CORE System, and determined the basic calculation method, and extracted the present calculation problem in case of application in K-CORE System and the future improvement items so on

Transient voltage control of a DFIG-based wind power plant for suppressing overvoltage using a reactive current reduction loop

Directory of Open Access Journals (Sweden)

Geon Park

2016-01-01

Full Text Available This paper proposes a transient voltage control scheme of a doubly fed induction generator (DFIG-based wind power plant (WPP using a reactive current reduction loop to suppress the overvoltage at a point of interconnection (POI and DFIG terminal after a fault clearance. The change of terminal voltage of a DFIG is monitored at every predefined time period to detect the fault clearance. If the voltage change exceeds a set value, then the reactive current reduction loop reduces the reactive current reference in the DFIG controller using the step function. The reactive current injection of DFIGs in a WPP is rapidly reduced, and a WPP can rapidly suppress the overvoltage at a fault clearance because the reactive current reference is reduced. Using an electromagnetic transients program–released version (EMTP–RV simulator, the performance of the proposed scheme was validated for a model system comprising 20 units of a 5-MW DFIG considering various scenarios, such as fault and wind conditions. Test results show that the proposed scheme enables a WPP to suppress the overvoltage at the POI and DFIG terminal within a short time under grid fault conditions.

Reactive power compensator

Science.gov (United States)

El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Reactive power compensator

Energy Technology Data Exchange (ETDEWEB)

El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Polynomial curve fitting for control rod worth using least square numerical analysis

International Nuclear Information System (INIS)

Muhammad Husamuddin Abdul Khalil; Mark Dennis Usang; Julia Abdul Karim; Mohd Amin Sharifuldin Salleh

2012-01-01

RTP must have sufficient excess reactivity to compensate the negative reactivity feedback effects such as those caused by the fuel temperature and power defects of reactivity, fuel burn-up and to allow full power operation for predetermined period of time. To compensate this excess reactivity, it is necessary to introduce an amount of negative reactivity by adjusting or controlling the control rods at will. Control rod worth depends largely upon the value of the neutron flux at the location of the rod and reflected by a polynomial curve. Purpose of this paper is to rule out the polynomial curve fitting using least square numerical techniques via MATLAB compatible language. (author)

Structure reactivity relationships during N2O hydrogenation over Au-Ag alloys: A study by field emission techniques

Science.gov (United States)

Jacobs, Luc; Barroo, Cédric; Gilis, Natalia; Lambeets, Sten V.; Genty, Eric; Visart de Bocarmé, Thierry

2018-03-01

To make available atomic oxygen at the surface of a catalyst is the key step for oxidation reactions on Au-based catalysts. In this context, Au-Ag alloys catalysts exhibit promising properties for selective oxidation reactions of alcohols: low temperature activity and high selectivity. The presence of O(ads) and its effects on the catalytic reactivity is studied via the N2O dissociative adsorption and subsequent hydrogenation. Field emission techniques are particularly suited to study this reaction: Field Ion Microscopy (FIM) and Field Emission Microscopy (FEM) enable to image the extremity of sharp metallic tips, the size and morphology of which are close to those of one single catalytic particle. The reaction dynamics is studied in the 300-320 K temperature range and at a pressure of 3.5 × 10-3 Pa. The main results are a strong structure/reactivity relationship during N2O + H2 reaction over Au-8.8 at.%Ag model catalysts. Comparison of high-resolution FIM images of the clean sample and FEM images during reaction shows a sensitivity of the reaction to the local structure of the facets, independently of the used partial pressures of both N2O and H2. This suggests a localised dissociative adsorption step for N2O and H2 with the formation of a reactive interface around the {210} facets.

Enhanced Open-Circuit Voltage in Colloidal Quantum Dot Photovoltaics via Reactivity-Controlled Solution-Phase Ligand Exchange

KAUST Repository

Jo, Jea Woong; Kim, Younghoon; Choi, Jongmin; de Arquer, F. Pelayo Garcí a; Walters, Grant; Sun, Bin; Ouellette, Olivier; Kim, Junghwan; Proppe, Andrew H.; Quintero-Bermudez, Rafael; Fan, James; Xu, Jixian; Tan, Chih Shan; Voznyy, Oleksandr; Sargent, Edward H.

2017-01-01

The energy disorder that arises from colloidal quantum dot (CQD) polydispersity limits the open-circuit voltage (VOC) and efficiency of CQD photovoltaics. This energy broadening is significantly deteriorated today during CQD ligand exchange and film assembly. Here, a new solution-phase ligand exchange that, via judicious incorporation of reactivity-engineered additives, provides improved monodispersity in final CQD films is reported. It has been found that increasing the concentration of the less reactive species prevents CQD fusion and etching. As a result, CQD solar cells with a VOC of 0.7 V (vs 0.61 V for the control) for CQD films with exciton peak at 1.28 eV and a power conversion efficiency of 10.9% (vs 10.1% for the control) is achieved.

Enhanced Open-Circuit Voltage in Colloidal Quantum Dot Photovoltaics via Reactivity-Controlled Solution-Phase Ligand Exchange

KAUST Repository

Jo, Jea Woong

2017-10-09

The energy disorder that arises from colloidal quantum dot (CQD) polydispersity limits the open-circuit voltage (VOC) and efficiency of CQD photovoltaics. This energy broadening is significantly deteriorated today during CQD ligand exchange and film assembly. Here, a new solution-phase ligand exchange that, via judicious incorporation of reactivity-engineered additives, provides improved monodispersity in final CQD films is reported. It has been found that increasing the concentration of the less reactive species prevents CQD fusion and etching. As a result, CQD solar cells with a VOC of 0.7 V (vs 0.61 V for the control) for CQD films with exciton peak at 1.28 eV and a power conversion efficiency of 10.9% (vs 10.1% for the control) is achieved.

Control of ZrH reactor reactivity perturbations during orbital maneuvers

International Nuclear Information System (INIS)

Audette, R.F.

1970-01-01

Scheduled and inadvertent vehicle maneuvers in manned and unmanned space missions may result in reactivity perturbations to the ZrH reactor due to fuel and control drum motion from acceleration forces. Potential power and outlet coolant temperature excursions could result in interruptions of PCS power generation, or excessive coolant temperatures if uncontrolled. This analysis compares potential uncontrolled reactor transients with allowable transients for uninterrupted electrical power generation from a Brayton system, and presents a control scheme to limit transient reactor outlet temperatures to 1250 0 F for a system designed to operate at a nominal 1200 0 F reactor outlet. Potential uncontrolled transients could result in a reactor outlet temperature swing of +-77 0 F about a nominal 1200 0 F and a reactor power swing of +92 Kwt and -67 Kwt about a nominal 130 Kwt for the Brayton System. (U.S.)

The variation of the reactivity with the number, diameter and length of the control rods in a heavy water natural uranium reactor

Energy Technology Data Exchange (ETDEWEB)

McCriric, H

1958-05-15

Starting with the known reactor constants for a heavy water moderated reactor with reflector and a given number of control rods of a certain size, the reactivity equivalence of the control rods is calculated. The calculation is given in detail. The number, length and diameter of the control rods is then varied and the effect of these parameters on the reactivity is shown graphically. Flux plots are also given for the reactor with and without control rods.

Phase Angle Control of Three Level Inverter Based D-STATCOM Using Neuro-Fuzzy Controller

Directory of Open Access Journals (Sweden)

COTELI, R.

2012-02-01

Full Text Available Distribution Static Compensator (D-STATCOM is a shunt compensation device used to improve electric power quality in distribution systems. It is well-known that D-STATCOM is a nonlinear, semi-defined and time-varying system. Therefore, control of D-STATCOM by the conventional control techniques is very difficult task. In this paper, the control of D-STATCOM is carried out by the neuro-fuzzy controller (NFC which has non-linear and robust structure. For this aim, an experimental setup based on three-level H-bridge inverter is constructed. Phase angle control method is used for control of D-STATCOM's output reactive power. Control algorithm for this experimental setup is prepared in MATLAB/Simulink and downloaded to DS1103 controller card. A Mamdani type NFC is designed for control of D-STATCOM's reactive current. Output of NFC is integrated to increase tracking performance of controller in steady state. The performance of D-STATCOM is experimentally evaluated by changing reference reactive current as on-line. The experimental results show that the proposed controller gives very satisfactory performance under different loading conditions.

Detailed characterization of a Comparative Reactivity Method (CRM) instrument for ambient OH reactivity measurements: experiments vs. modeling

Science.gov (United States)

Michoud, Vincent; Locoge, Nadine; Dusanter, Sébastien

2015-04-01

The Hydroxyl radical (OH) is the main daytime oxidant in the troposphere, leading to the oxidation of Volatile Organic Compounds (VOCs) and the formation of harmful pollutants such as ozone (O3) and Secondary Organic Aerosols (SOA). While OH plays a key role in tropospheric chemistry, recent studies have highlighted that there are still uncertainties associated with the OH budget, i.e the identification of sources and sinks and the quantification of production and loss rates of this radical. It has been demonstrated that ambient measurements of the total OH loss rate (also called total OH reactivity) can be used to identify and reduce these uncertainties. In this context, the Comparative Reactivity Method (CRM), developed by Sinha et al. (ACP, 2008), is a promising technique to measure total OH reactivity in ambient air and has already been used during several field campaigns. This technique relies on monitoring competitive reactions of OH with ambient trace gases and a reference compound (pyrrole) in a sampling reactor to derive ambient OH reactivity. However, this technique requires a complex data processing chain that has yet to be carefully investigated in the laboratory. In this study, we present a detailed characterization of a CRM instrument developed at Mines Douai, France. Experiments have been performed to investigate the dependence of the CRM response on humidity, ambient NOx levels, and the pyrrole-to-OH ratio inside the sampling reactor. Box modelling of the chemistry occurring in the reactor has also been performed to assess our theoretical understanding of the CRM measurement. This work shows that the CRM response is sensitive to both humidity and NOx, which can be accounted for during data processing using parameterizations depending on the pyrrole-to-OH ratio. The agreement observed between laboratory studies and model results suggests a good understanding of the chemistry occurring in the sampling reactor and gives confidence in the CRM

Reactive Systems

DEFF Research Database (Denmark)

Aceto, Luca; Ingolfsdottir, Anna; Larsen, Kim Guldstrand

A reactive system comprises networks of computing components, achieving their goals through interaction among themselves and their environment. Thus even relatively small systems may exhibit unexpectedly complex behaviours. As moreover reactive systems are often used in safety critical systems......, the need for mathematically based formal methodology is increasingly important. There are many books that look at particular methodologies for such systems. This book offers a more balanced introduction for graduate students and describes the various approaches, their strengths and weaknesses, and when...... they are best used. Milner's CCS and its operational semantics are introduced, together with the notions of behavioural equivalences based on bisimulation techniques and with recursive extensions of Hennessy-Milner logic. In the second part of the book, the presented theories are extended to take timing issues...

Sweden: Autonomous Reactivity Control (ARC) Systems

International Nuclear Information System (INIS)

Qvist, Staffan A.

2015-01-01

The next generation of nuclear energy systems must be licensed, constructed, and operated in a manner that will provide a competitively priced supply of energy, keeping in consideration an optimum use of natural resources, while addressing nuclear safety, waste, and proliferation resistance, and the public perception concerns of the countries in which those systems are deployed. These issues are tightly interconnected, and the implementation of passive and inherent safety features is a high priority in all modern reactor designs since it helps to tackle many of the issues at once. To this end, the Autonomous Reactivity Control (ARC) system was developed to ensure excellent inherent safety performance of Generation-IV reactors while having a minimal impact on core performance and economic viability. This paper covers the principles for ARC system design and analysis, the problem of ensuring ARC system response stability and gives examples of the impact of installing ARC systems in well-known fast reactor core systems. It is shown that even with a relatively modest ARC installation, having a near-negligible impact on core performance during standard operation, cores such as the European Sodium Fast Reactor (ESFR) can be made to survive any postulated unprotected transient without coolant boiling or fuel melting

Controlling of Nitriding Process on Reactive Plasma Spraying of Al Particles

International Nuclear Information System (INIS)

Shahien, Mohammed; Yamada, Motohiro; Yasui, Toshiaki; Fukumoto, Masahiro

2011-01-01

Reactive plasma spraying (RPS) has been considered as a promising technology for in-situ formation of aluminum nitride (AlN) thermally sprayed coatings. To fabricate thick A lN coatings in RPS process, controlling and improving the in-flight nitriding reaction of Al particles is required. In this study, it was possible to control the nitriding reaction by using ammonium chloride (NH 4 Cl) powders. Thick and dense AlN coating (more than 300 μm thickness) was successfully fabricated with small addition of NH 4 Cl powders. Thus, addition of NH 4 Cl prevented the Al aggregation by changing the reaction pathway to a mild way with no explosive mode (relatively low heating rates) and it acts as a catalyst, nitrogen source and diluent agent.

Power system stabilizers based on modern control techniques

Energy Technology Data Exchange (ETDEWEB)

Malik, O P; Chen, G P; Zhang, Y; El-Metwally, K [Calgary Univ., AB (Canada). Dept. of Electrical and Computer Engineering

1994-12-31

Developments in digital technology have made it feasible to develop and implement improved controllers based on sophisticated control techniques. Power system stabilizers based on adaptive control, fuzzy logic and artificial networks are being developed. Each of these control techniques possesses unique features and strengths. In this paper, the relative performance of power systems stabilizers based on adaptive control, fuzzy logic and neural network, both in simulation studies and real time tests on a physical model of a power system, is presented and compared to that of a fixed parameter conventional power system stabilizer. (author) 16 refs., 45 figs., 3 tabs.

Synthesis and processing of composites by reactive metal penetration

Energy Technology Data Exchange (ETDEWEB)

Loehman, R.E.; Ewsuk, K.G. [Sandia National Laboratories, Albuquerque, NM (United States); Tomsia, A.P. [Pask Research and Engineering, Berkeley, CA (United States)] [and others

1995-05-01

Ceramic-metal composites are being developed because their high stiffness-to weight ratios, good fracture toughness, and variable electrical and thermal properties give them advantages over more conventional materials. However, because ceramic-metal composite components presently are more expensive than monolithic materials, improvements in processing are required to reduce manufacturing costs. Reactive metal penetration is a promising new method for making ceramic- and metal-matrix composites that has the advantage of being inherently a net-shape process. This technique, once fully developed, will provide another capability for manufacturing the advanced ceramic composites that are needed for many light-weight structural and wear applications. The lower densities of these composites lead directly to energy savings in use. Near-net-shape fabrication of composite parts should lead to additional savings because costly and energy intensive grinding and machining operations are significantly reduced, and the waste generated from such finishing operations is minimized. The goals of this research program are: (1) to identify feasible compositional systems for making composites by reactive metal penetration; (2) to understand the mechanism(s) of composite formation by reactive metal penetration; and (3) to learn how to control and optimize reactive metal penetration for economical production of composites and composite coatings.

Efficient Reactive Power Compensation Algorithm for Distribution Network

Directory of Open Access Journals (Sweden)

J. Jerome

2017-12-01

Full Text Available The use of automation and energy efficient equipment with electronic control would greatly improve industrial production.  These new devices are more sensitive to supply voltage deviation and the characteristics of the power system that was previously ignored are now very important. Hence the benefits of distribution automation have been widely acknowledged in recent years. This paper proposes an efficient load flow solution technique extended to find optimum location for reactive power compensation and network reconfiguration for planning and day-to-day operation of distribution networks.  This is required as a part of the distribution automation system (DAS for taking various control and operation decisions.  The method exploits the radial nature of the network and uses forward and backward propagation technique to calculate branch currents and node voltages.  The proposed method has been tested to analyze several practical distribution networks of various voltage levels and also having high R/X ratio.

A novel technique for active vibration control, based on optimal

Indian Academy of Sciences (India)

In the last few decades, researchers have proposed many control techniques to suppress unwanted vibrations in a structure. In this work, a novel and simple technique is proposed for the active vibration control. In this technique, an optimal tracking control is employed to suppress vibrations in a structure by simultaneously ...

Reactivity balance for a soluble boron-free small modular reactor

Directory of Open Access Journals (Sweden)

Lezani van der Merwe

2018-06-01

Full Text Available Elimination of soluble boron from reactor design eliminates boron-induced reactivity accidents and leads to a more negative moderator temperature coefficient. However, a large negative moderator temperature coefficient can lead to large reactivity feedback that could allow the reactor to return to power when it cools down from hot full power to cold zero power. In soluble boron-free small modular reactor (SMR design, only control rods are available to control such rapid core transient.The purpose of this study is to investigate whether an SMR would have enough control rod worth to compensate for large reactivity feedback. The investigation begins with classification of reactivity and completes an analysis of the reactivity balance in each reactor state for the SMR model.The control rod worth requirement obtained from the reactivity balance is a minimum control rod worth to maintain the reactor critical during the whole cycle. The minimum available rod worth must be larger than the control rod worth requirement to manipulate the reactor safely in each reactor state. It is found that the SMR does have enough control rod worth available during rapid transient to maintain the SMR at subcritical below k-effectives of 0.99 for both hot zero power and cold zero power. Keywords: Control Rod Worth, Reactivity Balance, Reactivity Feedback, Small Modular Reactor, Soluble Boron Free

Design report on the guide box-reactivity and safety control plates for MPR reactor under normal operation conditions

International Nuclear Information System (INIS)

Markiewicz, M.

1999-01-01

The reactivity control system for the MPR reactor (Multi Purpose Reactor) is a critical component regarding safety, it must ensure a fast shut down, maintaining the reactor in subcritical condition under normal or accidental operation condition. For this purpose, this core component must be designed to maintain its operating capacity during all the residence time and under any foreseen operation condition. The mechanical design of control plates and guide boxes must comply with structural integrity, maintaining its geometric and dimensional stability within the pre-established limits to prevent interferences with other core components. For this, the heat generation effect, mechanical loads and environment and irradiation effects were evaluated during the mechanical design. The reactivity control system is composed of guide boxes, manufactured from Aluminium alloy, located between the fuel elements, and control absorber plates of Ag-In-Cd alloy hermetically enclosed by a cladding of stainless steel sliding inside de guide boxes. The upward-downward movement is transmitted by a rod from the motion device located at the reactor lower part. The design requirements, criteria and limits were established to fulfill with the normal and abnormal operation conditions. The design verifications were performed by analytical method, estimating the guide box and control plates residence time. The result of the analysis performed, shows that the design of the reactivity control system and the material selected, are appropriate to fulfill the functional requirements, with no failures attributed to the mechanical design. (author)

A Hybrid Cognitive-Reactive Multi-Agent Controller

National Research Council Canada - National Science Library

Bugajska, Magdalena D; Schultz, Alan C; Trafton, J. G; Taylor, Matthew; Mintz, Farilee E

2002-01-01

...). In this system, the learning algorithm handles reactive aspects of the task and provides an adaptation mechanism, while the cognitive model handles cognitive aspects of the task and ensures the realism of the behavior...

Active load control techniques for wind turbines.

Energy Technology Data Exchange (ETDEWEB)

van Dam, C.P. (University of California, Davis, CA); Berg, Dale E.; Johnson, Scott J. (University of California, Davis, CA)

2008-07-01

This report provides an overview on the current state of wind turbine control and introduces a number of active techniques that could be potentially used for control of wind turbine blades. The focus is on research regarding active flow control (AFC) as it applies to wind turbine performance and loads. The techniques and concepts described here are often described as 'smart structures' or 'smart rotor control'. This field is rapidly growing and there are numerous concepts currently being investigated around the world; some concepts already are focused on the wind energy industry and others are intended for use in other fields, but have the potential for wind turbine control. An AFC system can be broken into three categories: controls and sensors, actuators and devices, and the flow phenomena. This report focuses on the research involved with the actuators and devices and the generated flow phenomena caused by each device.

Entropy-based critical reaction time for mixing-controlled reactive transport

DEFF Research Database (Denmark)

Chiogna, Gabriele; Rolle, Massimo

2017-01-01

Entropy-based metrics, such as the dilution index, have been proposed to quantify dilution and reactive mixing in solute transport problems. In this work, we derive the transient advection dispersion equation for the entropy density of a reactive plume. We restrict our analysis to the case where...... the concentration distribution of the transported species is Gaussian and we observe that, even in case of an instantaneous complete bimolecular reaction, dilution caused by dispersive processes dominates the entropy balance at early times and results in the net increase of the entropy density of a reactive species...

Two applications of airtightness control techniques on big assemblies

CERN Document Server

Devallan, C; Marcellin, J

1973-01-01

Deals with two airtightness control techniques respectively applied on intersecting storage rings (ISR) at CERN in Geneva and on a liquid methane storage tank. These two big assemblies called for two different control techniques which use helium and ammonia respectively as tracer gas. Existing practical leakage detection techniques to meet industrial needs are discussed at the end of the article. (2 refs).

State and data techniques for control of discontinuous systems

International Nuclear Information System (INIS)

Kisner, R.A.

1986-01-01

The need for automated control systems becomes clear as the complexity of nuclear power plants increases and economic incentives demand higher plant availability. A control system with intelligence distributed throughout its controllers allows reduction in operator workload, perhaps reduction in crew size, and potentially a reduction in on-line human error. In automated systems of this kind, each controller should be capable of making decisions and carrying out a plan of action. This paper describes a technique for structured analysis and design of automated control systems. The technique integrates control of continuous and discontinuous nuclear power plant subsystems and components. A hierarchical control system with distributed intelligence follows from applying the technique. Further, it can be applied to all phases of control system design. For simplicity, the example used in the paper is limited to phase I design (basic automatic control action), in which no maintenance, testing, or contingency capability is attempted

Quick monitoring of pozzolanic reactivity of waste ashes.

Science.gov (United States)

Sinthaworn, Suppachai; Nimityongskul, Pichai

2009-05-01

This article proposes a quick method of monitoring for pozzolanic reactivity of waste ashes by investigating the electrical conductivity of the suspension at an elevated temperature. This suspension is obtained by mixing tested pozzolan with an ordinary Portland cement (OPC) solution produced by mixing ordinary Portland cement with water. For comparison, silica fume, metakaolin, rice husk ash and river sand - whose pozzolanic reactivities range from reactive to inert - were used in the experimental investigation. The electrical conductivity of the suspension was continually recorded by using an electrical conductivity meter and stored by using a personal computer for a period of slightly over 1day. The indicative parameters that can be related to pozzolanic reactivity were discussed and analyzed in detail. It was found that it is possible to determine the pozzolanic reactivity of fly ash within 28h by using the proposed technique, as compared to 7 or 28 days for the determination of strength activity index according to ASTM. This technique would help concrete technologists to speedily investigate the quality of fly ash for use as a cement replacement in order to alleviate pollution caused by cement production and solve disposal problems of waste ashes.

Measurement of the anti reactivity of a control rod of G1, by a slow oscillation method

International Nuclear Information System (INIS)

Breton, D.; Leroy, J.; Vidal, R.

1957-01-01

It is possible to determine the effect of the end of a control rod on the reactivity of the pile by measuring the modulation induced in the neutron flux by the slow oscillation of this control rod. The total effect of the control rod can be deduced, given certain hypothesis and corrections, from the experimental curve giving the effect of the end of the rod as a function of its position. This method has the advantage of permitting the measurement of very large anti reactivities, such as p= 10 -2 for example, which would not be possible by other kinetic methods. Thus the control rod B 3 , in the low position, brings about a reduction in reactivity equal to 1130 p.c.m. ± 30 in the pile charged with 518 fuel elements, on one side only of the slit. We have compared the oscillation method with the classical divergence method, in the fields where the two measurements were possible: a satisfactory agreement was found. We have established that the phase displacement between the oscillation of the rod and the modulation of the flux varied greatly with the position of the rod. This variation cannot be explained on the basis of the dynamic model independent of space; we have attributed it to the influence of spatial harmonics of the flux distribution, and have determined a correction which frees the measurements of this influence. (author) [fr

Controlling of Nitriding Process on Reactive Plasma Spraying of Al Particles

Energy Technology Data Exchange (ETDEWEB)

Shahien, Mohammed [Graduate Student, Toyohashi University of Technology (Japan); Yamada, Motohiro; Yasui, Toshiaki; Fukumoto, Masahiro, E-mail: mo.shahien@yahoo.com [Toyohashi University of Technology (Japan)

2011-10-29

Reactive plasma spraying (RPS) has been considered as a promising technology for in-situ formation of aluminum nitride (AlN) thermally sprayed coatings. To fabricate thick A lN coatings in RPS process, controlling and improving the in-flight nitriding reaction of Al particles is required. In this study, it was possible to control the nitriding reaction by using ammonium chloride (NH{sub 4}Cl) powders. Thick and dense AlN coating (more than 300 {mu}m thickness) was successfully fabricated with small addition of NH{sub 4}Cl powders. Thus, addition of NH{sub 4}Cl prevented the Al aggregation by changing the reaction pathway to a mild way with no explosive mode (relatively low heating rates) and it acts as a catalyst, nitrogen source and diluent agent.

Analysis of RSG-GAS Control Rod Worth Due to Perturbation Reactivity

International Nuclear Information System (INIS)

Taswanda Taryo

2004-01-01

The control rod interaction effect of RSG-GAS typical working core was studied using a method based on the exact perturbation theory with three simplifying assumptions which require only N+1 criticality calculations. The interaction effect between two interacting rods reached up to 19 % while the interaction effect of multiple interacting rods reached up to 32 % for all (8) control rods involved. The accuracy of the adopted method were extensively investigated to determine the error sources and the magnitude of the error. Through comparison of the present results with ones of the simple summation method, it was obvious that the adopted method was superior in that a significant improvement on the accuracy of the calculated reactivity worth can be achieved with a small number of criticality calculations. (author)

Redox-controlled memristive switching in the junctions employing Ti reactive electrodes

Directory of Open Access Journals (Sweden)

Haitao Li

2011-09-01

Full Text Available We have proposed a kind of memristive device based on the junctions employing Ti as the reactive electrodes. The role of electrically-derived redox of Ti in such memristive switching is shown. The structural and chemical evidence of the electrically-derived oxidation is presented by TEM and XPS experiment, respectively. Due to the redox of the top electrode Ti and the consequent drift of oxygen vacancies, the device shows two distinct resistance states under a sweeping voltage loading. ON state is controlled by tunneling process, while OFF state is controlled by Schottky emission conductive mechanism. The failure behaviors of such memristive junctions are also discussed. In the light of the redox principle, we demonstrate that the devices could be recovered by loading a long electrical reduction treatment.

High efficiency H6 single-phase transformerless grid-tied PV inverter with proposed modulation for reactive power generation

Science.gov (United States)

Almasoudi, Fahad M.; Alatawi, Khaled S.; Matin, Mohammad

2017-08-01

Implementation of transformerless inverters in PV grid-tied system offer great benefits such as high efficiency, light weight, low cost, etc. Most of the proposed transformerless inverters in literature are verified for only real power application. Currently, international standards such as VDE-AR-N 4105 has demanded that PV grid-tied inverters should have the ability of controlling a specific amount of reactive power. Generation of reactive power cannot be accomplished in single phase transformerless inverter topologies because the existing modulation techniques are not adopted for a freewheeling path in the negative power region. This paper enhances a previous high efficiency proposed H6 trnasformerless inverter with SiC MOSFETs and demonstrates new operating modes for the generation of reactive power. A proposed pulse width modulation (PWM) technique is applied to achieve bidirectional current flow through freewheeling state. A comparison of the proposed H6 transformerless inverter using SiC MOSFETs and Si MOSFTEs is presented in terms of power losses and efficiency. The results show that reactive power control is attained without adding any additional active devices or modification to the inverter structure. Also, the proposed modulation maintains a constant common mode voltage (CM) during every operating mode and has low leakage current. The performance of the proposed system verifies its effectiveness in the next generation PV system.

Application of B{sub 4}C/Al{sub 2}O{sub 3} Burnable Absorber Rod to Control Excess Reactivity of SMR

Energy Technology Data Exchange (ETDEWEB)

Muth, Boravy; Hah, C. J. [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2016-10-15

Soluble boron in a nuclear reactor coolant is one of the methods to control excess reactivity of the reactor. However, the use of soluble boron also causes some negative effects such as corrosion, more-positive tendency of Moderator Temperature Coefficient (MTC) and the requirement of Chemical Volume Control System (CVCS). One of the conceptual design features of SMR having been developed in Korea is soluble boron- free reactor to eliminate those drawbacks. Control rods and Burnable Absorber (BA) rods can be other methods than soluble to control excess reactivity. WABA (Wet Annular Burnable Absorber) and PYREX are such type. The other type is IFBA (Integral Fuel Burnable Absorber) in which fuel pellet surface is coated with BA. This paper compares nuclear characteristics of three types of BA as well as SLOBA in terms of k-infinite vs. burnup and explain design basis of SLOBA. This paper also presents the application of SLOBA rods to control long-term excess reactivity of SMR. The SMR loaded with SLOBA rods has been developed for the past few years in Korean. It is named as Bandi-50 with design features of 180 MWth, 37 FAs, fuel assembly height of 200 cm. Soluble-boron-free is one of nuclear design requirements of Bandi-50 and is achieved by controlling excess reactivity of the SMR using BAs and control rods only. To achieve this design requirement, LP is carefully determined in such way that CBC should be as low as possible. Fuel assembly cross-sections are generated by CASMO-3, and core depletion calculations are performed by MASTER.

Refinement of Parallel and Reactive Programs

OpenAIRE

Back, R. J. R.

1992-01-01

We show how to apply the refinement calculus to stepwise refinement of parallel and reactive programs. We use action systems as our basic program model. Action systems are sequential programs which can be implemented in a parallel fashion. Hence refinement calculus methods, originally developed for sequential programs, carry over to the derivation of parallel programs. Refinement of reactive programs is handled by data refinement techniques originally developed for the sequential refinement c...

Retrofitting of Reinforced Concrete Beams using Reactive Powder Concrete (RPC)

Science.gov (United States)

Karthik, S.; Sundaravadivelu, Karthik

2017-07-01

Strengthening of existing damaged structures is one of the leading studies in civil engineering. The purpose of retrofitting is to structurally treat the member with an aim to restore the structure to its original strength. The focus of this project is to study the behaviour of damaged Reinforced Concrete beam retrofitted with Reactive Powder Concrete (RPC) Overlay. Reinforced concrete beams of length 1200 mm, width 100 mm and depth 200 mm were casted with M30 grade of concrete in the laboratory and cured for 28 days. One beam is taken as control and are tested under two point loading to find out ultimate load. Remaining beams are subjected to 90 % ultimate load of control beams. The partially damaged beams are retrofitted with Reactive Powder Concrete Overlay at the full tension face of the beam and side overlay depends upon the respectable retrofitting techniques with 10 mm and 20 mm thick layer to find optimum. Materials like steel fibres are added to enhance the ductility by eliminating coarse particle for homogeneity of the structure. Finally, the modes of failure for retrofitted beams are analysed experimentally under two point loading & compared the results with Control beam.

An Optimal Reactive Power Control Strategy for a DFIG-Based Wind Farm to Damp the Sub-Synchronous Oscillation of a Power System

Directory of Open Access Journals (Sweden)

Bin Zhao

2014-05-01

Full Text Available This study presents the auxiliary damping control with the reactive power loop on the rotor-side converter of doubly-fed induction generator (DFIG-based wind farms to depress the sub-synchronous resonance oscillations in nearby turbogenerators. These generators are connected to a series capacitive compensation transmission system. First, the damping effect of the reactive power control of the DFIG-based wind farms was theoretically analyzed, and a transfer function between turbogenerator speed and the output reactive power of the wind farms was introduced to derive the analytical expression of the damping coefficient. The phase range to obtain positive damping was determined. Second, the PID phase compensation parameters of the auxiliary damping controller were optimized by a genetic algorithm to obtain the optimum damping in the entire subsynchronous frequency band. Finally, the validity and effectiveness of the proposed auxiliary damping control were demonstrated on a modified version of the IEEE first benchmark model by time domain simulation analysis with the use of DigSILENT/PowerFactory. Theoretical analysis and simulation results show that this derived damping factor expression and the condition of the positive damping can effectively analyze their impact on the system sub-synchronous oscillations, the proposed wind farms reactive power additional damping control strategy can provide the optimal damping effect over the whole sub-synchronous frequency band, and the control effect is better than the active power additional damping control strategy based on the power system stabilizator.

Distributed control of hybrid AC microgrids with dynamic active and reactive power capacity tuning

DEFF Research Database (Denmark)

Nutkani, Inam Ullah; Loh, Poh Chiang; Blaabjerg, Frede

2012-01-01

Microgrids comprise of emerging generation technologies such as fuel cell, solar PV, wind turbine generator, storage and loads. They can, in principle, operate at different voltages and frequencies. Tying them either to the mains grid or among themselves would certainly require some interlinking...... power converters, whose control should preferably be done autonomously without demanding communication links. This paper proposes distributed control for power management between two Microgrids interlinked through inverters. The control scheme aims to reduce the reactive power loading stress on DERs...... and also allows active power transfer from overloaded grid to under- loaded grid. The performance of proposed control has been verified in simulation and through a scaled-down experimental system....

A multi-objective control strategy for grid connection of DG (distributed generation) resources

Energy Technology Data Exchange (ETDEWEB)

Pouresmaeil, Edris; Montesinos-Miracle, Daniel; Bergas-Jane, Joan [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Departament d' Enginyeria Electrica, Universitat Politecnica de Catalunya, ETS d' Enginyeria Industrial de Barcelona (Spain); Gomis-Bellmunt, Oriol [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Departament d' Enginyeria Electrica, Universitat Politecnica de Catalunya, ETS d' Enginyeria Industrial de Barcelona (Spain); Catalonia Institute for Energy Research IREC, Barcelona (Spain)

2010-12-15

This paper presents a flexible control technique for connection of DG (distributed generation) resources to distribution networks, especially during ride-through on faulty grid. This strategy is derived from the abc/{alpha}{beta} and {alpha}{beta}/dq transformations of the ac system variables. The active and reactive currents injected by the DG source are controlled in the synchronously rotating orthogonal dq reference frame. The transformed variables are used to control the VSI (voltage source inverter) which connects the DG to the distribution network. Using a P.L.L. (phase locked loop) in circuit of proposed control technique, the angle of positive sequence has been detected, in order to synchronize the currents to the distribution network. The proposed control technique has the capability of providing active and reactive powers and harmonic currents to nonlinear loads with a fast dynamic response. Simulation results and mathematical analysis have been completed in order to achieve a reduced THD (total harmonic distortion), increased power factor and compensated load's active and reactive powers. The analyses show the high performance of this control strategy in DG applications in comparison with other existing strategies. (author)

Requirements Engineering for Reactive Systems: Coloured Petri Nets for an Elevator Controller

DEFF Research Database (Denmark)

Jørgensen, Jens Bæk; Fernandes, Joao Miguel; Tjell, Simon

2007-01-01

This paper presents a model-based approach to requirements engineering for reactive systems; we use an elevator controller as case study. We identify and justify two key properties that a model which we construct must have, namely: (1) controller-and-environment-partitioned, which means...... constituting a description of both the controller and the environment, and distinguishing between these two domains and between desired and assumed behaviour; (2) use case-based, which means constructed on the basis of a given use case diagram and reproducing the behaviour described in accompanying scenario...... descriptions. For the case study, we build an executable model in the formal modelling language Coloured Petri Nets. We demonstrate how this model is useful for requirements engineering, since it provides a solid basis for addressing behavioural issues early in the development process, for example regarding...

Estimation of quasi-critical reactivity

International Nuclear Information System (INIS)

Racz, A.

1992-02-01

The bank of Kalman filter method for reactivity and neutron density estimation originally suggested by D'Attellis and Cortina is critically overviewed. It is pointed out that the procedure cannot be applied reliably in such a form as the authors proposed, due to the filter divegence. An improved method, which is free from devergence problems are presented, as well. A new estimation technique is proposed and tested using computer simulation results. The procedure is applied for the estimation of small reactivity changes. (R.P.) 9 refs.; 2 figs.; 2 tabs

An experimental technique for the direct measurement of N2O5 reactivity on ambient particles

Directory of Open Access Journals (Sweden)

T. H. Bertram

2009-06-01

Full Text Available An experimental approach for the direct measurement of trace gas reactivity on ambient aerosol particles has been developed. The method utilizes a newly designed entrained aerosol flow reactor coupled to a custom-built chemical ionization mass spectrometer. The experimental method is described via application to the measurement of the N2O5 reaction probability, γ (N2O5. Laboratory investigations on well characterized aerosol particles show that measurements of γ (N2O5 observed with this technique are in agreement with previous observations, using conventional flow tube methods, to within ±20% at atmospherically relevant particle surface area concentrations (0–1000 μm2 cm−3. Uncertainty in the measured γ (N2O5 is discussed in the context of fluctuations in potential ambient biases (e.g., temperature, relative humidity and trace gas loadings. Under ambient operating conditions we estimate a single-point uncertainty in γ (N2O5 that ranges between ± (1.3×10-2 + 0.2×γ (N2O5, and ± (1.3×10-3 + 0.2×γ (N2O5 for particle surface area concentrations of 100 to 1000 μm2 cm−3, respectively. Examples from both laboratory investigations and field observations are included alongside discussion of future applications for the reactivity measurement and optimal deployment locations and conditions.

Reactivity to smartphone-based ecological momentary assessment of depressive symptoms (MoodMonitor: protocol of a randomised controlled trial

Directory of Open Access Journals (Sweden)

Wouter van Ballegooijen

2016-10-01

Full Text Available Abstract Background Ecological momentary assessment (EMA of mental health symptoms may influence the symptoms that it measures, i.e. assessment reactivity. In the field of depression, EMA reactivity has received little attention. We aim to investigate whether EMA of depressive symptoms induces assessment reactivity. Reactivity will be operationalised as an effect of EMA on depressive symptoms measured by a retrospective questionnaire, and, secondly, as a change in response rate and variance of the EMA ratings. Methods This study is a 12-week randomised controlled trial comprising three groups: group 1 carries out EMA of mood and completes a retrospective questionnaire, group 2 carries out EMA of how energetic they feel and completes a retrospective questionnaire, group 3 is the control group, which completes only the retrospective questionnaire. The retrospective questionnaire (Centre for Epidemiologic Studies Depression scale; CES-D assesses depressive symptoms and is administered at baseline, 6 weeks after baseline and 12 weeks after baseline. We aim to recruit 160 participants who experience mild to moderate depressive symptoms, defined as a Patient Health Questionnaire (PHQ-9 score of 5 to 15. This study is powered to detect a small between-groups effect, where no clinically relevant effect is defined as the effect size margin −0.25< d <0.25. Discussion To our knowledge, this is the first study to investigate whether self-rated EMA of depressive symptoms could induce assessment reactivity among mildly depressed individuals. Trial registration Netherlands Trial Register NTR5803. Registered 12 April 2016. http://www.trialregister.nl/trialreg/admin/rctview.asp?TC=5803 .

ERP Correlates of Proactive and Reactive Cognitive Control in Treatment-Naïve Adult ADHD.

Directory of Open Access Journals (Sweden)

Venke Arntsberg Grane

Full Text Available This study investigated whether treatment naïve adults with Attention Deficit Hyperactivity Disorder (ADHD; n = 33; 19 female differed from healthy controls (n = 31; 17 female in behavioral performance, event-related potential (ERP indices of preparatory attention (CueP3 and late CNV, and reactive response control (Go P3, NoGo N2, and NoGo P3 derived from a visual cued Go/NoGo task. On several critical measures, Cue P3, late CNV, and NoGo N2, there were no significant differences between the groups. This indicated normal preparatory processes and conflict monitoring in ADHD patients. However, the patients had attenuated Go P3 and NoGoP3 amplitudes relative to controls, suggesting reduced allocation of attentional resources to processes involved in response control. The patients also had a higher rate of Go signal omission errors, but no other performance decrements compared with controls. Reduced Go P3 and NoGo P3 amplitudes were associated with poorer task performance, particularly in the ADHD group. Notably, the ERPs were not associated with self-reported mood or anxiety. The results provide electrophysiological evidence for reduced effortful engagement of attentional resources to both Go and NoGo signals when reactive response control is needed. The absence of group differences in ERP components indexing proactive control points to impairments in specific aspects of cognitive processes in an untreated adult ADHD cohort. The associations between ERPs and task performance provided additional support for the altered electrophysiological responses.

Development of reactivity feedback effect measurement techniques under sub-critical condition in fast reactors

International Nuclear Information System (INIS)

Kitano, A.; Nishi, H.; Suzuki, T.; Okajima, S.; Kanemoto, S.

2012-01-01

The first-of-a-kind reactor has been licensed by a safety examination of the plant design based on the measured data in precedent mock-up experiments. The validity of the safety design can be confirmed without a mock-up experiment, if the reactor feed-back characteristics can be measured before operation, with the constructed reactor itself. The 'Synthesis Method', a systematic and sophisticated method of sub-criticality measurement, is proposed in this work to ensure the safety margin before operation. The 'Synthesis Method' is based on the modified source multiplication method (MSM) combined with the noise analysis method to measure the reference sub-criticality level for MSM. A numerical simulation for the control-rod reactivity worth and the isothermal feed-back reactivity was conducted for typical fast reactors of 100 MWe-size, 300 MWe-size, 750 MWe-size, and 1500 MWe-size to investigate the applicability of Synthesis Method. The number of neutron detectors and their positions necessary for the measurement were investigated for both methods of MSM and the noise analysis by a series of parametric survey calculations. As a result, it was suggested that a neutron detector located above the core center and three or more neutron detectors located above the radial blanket region enable the measurement of sub-criticality within 10% uncertainty from -$0.5 to -$2 and within 15% uncertainty for the deeper sub-criticality. (authors)

Towards a Reactive Power Oscillation Damping Controller for Wind Power Plant Based on Full Converter Wind Turbines

DEFF Research Database (Denmark)

Knüppel, Thyge; Kumar, Sathess; Thuring, Patrik

2012-01-01

In this paper a power oscillation damping controller (POD) based on modulation of reactive power (Q POD) is analyzed where the modular and distributed characteristics of the wind power plant (WPP) are considered. For a Q POD it is essential that the phase of the modulated output is tightly...... contributes to a collective response. This ability is shown with a 150 wind turbine (WT) WPP with all WTs represented, and it is demonstrated that the WPP contributes to the inter-area damping. The work is based on a nonlinear, dynamic model of the 3.6 MW Siemens Wind Power WT....... controlled to achieve a positive damping contribution. It is investigated how a park level voltage, reactive power, and power factor control at different grid strengths interact with the Q POD in terms of a resulting phase shift. A WPP is modular and distributed and a WPP Q POD necessitate that each WT...

Determination of reactivity coefficients from measurable effects of small external perturbations using a bank of Kalman filters

International Nuclear Information System (INIS)

Racz, A.

1990-12-01

The goal of this paper is to present a method for the determination of reactivity coefficients in a nuclear power reactor in operation. A method based on Kalman filtering technique and the Magill-Bogler test is proposed for the determination of reactivity coefficients from measured effects of small external perturbation introduced into a steady-state power reactor. Numerical experiments are presented to justify the procedure. A realistic problem is considered: the calculation of the control rod worth. Finally a possible way is given to check the goodness of the estimation. (author) 16 refs.; 4 figs

Literature Survey on Operational Voltage Control and Reactive Power Management on Transmission and Sub-Transmission Networks

Energy Technology Data Exchange (ETDEWEB)

Elizondo, Marcelo A.; Samaan, Nader A.; Makarov, Yuri V.; Holzer, Jesse T.; Vallem, Mallikarjuna R.; Huang, Renke; Vyakaranam, Bharat GNVSR; Ke, Xinda; Pan, Feng

2017-10-02

Voltage and reactive power system control is generally performed following usual patterns of loads, based on off-line studies for daily and seasonal operations. This practice is currently challenged by the inclusion of distributed renewable generation, such as solar. There has been focus on resolving this problem at the distribution level; however, the transmission and sub-transmission levels have received less attention. This paper provides a literature review of proposed methods and solution approaches to coordinate and optimize voltage control and reactive power management, with an emphasis on applications at transmission and sub-transmission level. The conclusion drawn from the survey is that additional research is needed in the areas of optimizing switch shunt actions and coordinating all available resources to deal with uncertain patterns from increasing distributed renewable generation in the operational time frame. These topics are not deeply explored in the literature.

Investigation of the behavior of a three phase grid-connected photovoltaic system to control active and reactive power

Energy Technology Data Exchange (ETDEWEB)

Tsengenes, Georgios; Adamidis, Georgios [Department of Electrical Engineering and Computer Engineering, Democritus University of Thrace, University Campus Kimmeria, 67100 Xanthi (Greece)

2011-01-15

In this paper, a photovoltaic (PV) system, with maximum power point tracking (MPPT), connected to a three phase grid is presented. The connection of photovoltaic system on the grid takes place in one stage using voltage source inverter (VSI). For a better utilization of the photovoltaic system, the control strategy applied is based on p-q theory. According to this strategy during sunlight the system sends active power to the grid and at the same time compensates the reactive power of the load. In case there is no sunlight (during the night for instance), the inverter only compensates the reactive power of the load. In this paper the use of p-q theory to supply the grid with active power and compensate the reactive power of the load is investigated. The advantage of this control strategy is that the photovoltaic system is operated the whole day. Furthermore, the p-q theory uses simple algebraic calculations without demanding the use of PLL to synchronize the inverter with the grid. (author)

Reactivity considerations for the on-line refuelling of a pebble bed modular reactor—Illustrating safety for the most reactive core fuel load

International Nuclear Information System (INIS)

Reitsma, Frederik

2012-01-01

In the multi-pass fuel management scheme employed for the pebble bed modular reactor the fuel pebbles are re-circulated until they reach the target burn-up. The rate at which fresh fuel is loaded and burned fuel is discharged is a result of the core neutronics cycle analysis but in practice (on the plant) this has to be controlled and managed by the fuel handling and storage system and use of the burnup measurement system. The excess reactivity is the additional reactivity available in the core during operating conditions that is the result of loading a fuel mixture in the core that is more reactive (less burned) than what is required to keep the reactor critical at full power operational conditions. The excess reactivity is balanced by the insertion of the control rods to keep the reactor critical. The excess reactivity allows flexibility in operations, for example to overcome the xenon build up when power is decreased as part of load follow. In order to limit reactivity excursions and to ensure safe shutdown the excess reactivity and thus the insertion depth of the control rods at normal operating conditions has to be managed. One way to do this is by operational procedures. The reactivity effect of long-term operation with the control rods inserted deeper than the design point is investigated and a control rod insertion limit is proposed that will not limit normal operations. The effects of other phenomena that can increase the power defect, such as higher-than-expected fuel temperatures, are also introduced. All of these cases are then evaluated by ensuring cold shutdown is still achievable and where appropriate by reactivity insertion accident analysis. These aspects are investigated on the PBMR 400 MW design.

A revision of sensitivity analysis for small reactivity effects in ZPRs

International Nuclear Information System (INIS)

Ros, Paul; Blaise, Patrick; Gruel, Adrien; Leconte, Pierre

2017-01-01

Sensitivity analysis appears to be an important element for nuclear data improvement experiments. Indeed, it brings significant information on the contribution of the isotopes involved in the measurements performed in Zero Power Reactors (ZPRs), particularly oscillation measurements like in MINERVE, and its successor ZEPHYR (Zero power Experimental PHYsics Reactor), currently being designed at CEA. Oscillation measurements consist in oscillating a small sample made of separated isotopes (or irradiated fuels) in the core center. Then, two perturbations occur: a local one corresponding to the flux modification around the sample, and a global one which corresponds to the induced variation of reactivity. This variation of reactivity is either uncontrolled (open loop) or automatically compensated by an external pilot rod (closed loop) to keep the configuration in its critical state. Representativity studies are used in order to evaluate the pertinence of an experiment configuration versus a targeted application. For oscillation experiments, sensitivity of the reactivity effects to nuclear data is needed to obtain such coefficients. The Equivalent Generalized Perturbation Theory (EGPT) method, based on an approximation of the Generalized Perturbation. Theory, is currently applied in the ERANOS code for control rod insertions and other important variations of reactivity. However, such reactivity insertions induce consequent reactivity changes and variations of the flux, whereas oscillations induce maximal reactivity effects of 10 pcm (10 10 -5 Δk/k ) and consequently very local variations of the flux surrounding the sample. Therefore, such numerical methods are not necessarily adapted to the calculation of small reactivity effect sensitivities to nuclear data. The influence of peripheral isotopes (through their cross-sections) to central measurements is evaluated thanks to the deterministic EGPT method and the Monte-Carlo technique of correlated samples. Large

Spatial neutronics modelling to evaluate the temperature reactivity feedbacks in a lead-cooled fast reactor - 15288

International Nuclear Information System (INIS)

Lorenzi, S.; Cammi, A.; Luzzi, L.

2015-01-01

The qualitative and quantitative assessment of the thermal reactivity feedbacks occurring in a nuclear reactor is a crucial issue for the time-dependent evolution of the system and, in turn, it has a great impact on the development and validation of advanced control techniques. In the present work, in order to overcome the limitations of the classic Point Kinetics adopted in the control simulators, a spatial neutronics model, representing the neutron flux as sum of a spatial basis weighted by time-dependent coefficients, has been considered. The reference reactor is ALFRED, the European demonstrator of the Lead-cooled Fast Reactor technology. Average cross-sections for each fuel assembly, calculated by means of a Monte Carlo code, have been used to solve the partial differential equations of the neutron diffusion, exploiting the capabilities of the COMSOL software. Once obtained the spatial functions, the set of equations for studying the reactivity effects has been implemented in the MATLAB environment. Among the several temperature reactivity feedbacks, specific attention has been paid to the Doppler effect in the fuel and to the lead density effect. Several spatial bases have been calculated and their capability of representing the reactivity variation have been assessed. (authors)

An introduction to reactive power compensation for wind farms

Energy Technology Data Exchange (ETDEWEB)

Nigim, K.A. [Waterloo Univ., Ont. (Canada). Dept. of Electrical and Computer Engineering; Cairo Univ., Giza (Egypt). Faculty of Engineering; Zobaa, A.F.; El Amin, I. [King Fahd Univ. of Petroleum and Minerals, Dhahran (Saudi Arabia). Dept. of Electrical Engineering

2005-07-01

The paper summarises the refereed contributions of seven articles reviewed for publication in the IJETP - Special Issue on 'Reactive compensation for wind farms'. The main goal of the special issue is to provide a forum to exchange information on the reactive power compensation requirements for wind farms and introducing possible price mechanisms for today's deregulated power industry. Uncompensated reactive power causes stress on the hosting utility grid as well as added expenses, which create in difficulties for power purchasing agreements from independent wind energy producers. Wind power producers need to comply with the hosting utility grid interconnection standards, e.g., voltage and frequency, as well as to provide controllable active and reactive sources of power. Active power supply is mainly dependent on the potential of wind power produced and the turbine design. Reactive power demand on the other hand depends on the conversion devices and the recovered power quantity fed to the grid. Static Var Compensators (SVC), Unified Power Quality Conditioners (UPQC), Unified Power Flow Controllers (UPFC), and the Distributed Static Synchronous Compensators (DSTATCOM) are all new emerging devices aimed at regulating the reactive power requirements. The excellent controllability of these devices has paved the way to flexible and dynamic controllers that are capable of regulating the flow of active and reactive power components. These devices are now suggested for the control of the reactive power requirement of wind generators. Studies have demonstrated acceptable voltage stabilisation results. This has increased the penetration level of wind power into existing distribution networks in many countries. (Author)

An introduction to reactive power compensation for wind farms

International Nuclear Information System (INIS)

Nigim, K.A.; Cairo Univ., Giza; Zobaa, A.F.; El Amin, I.

2005-01-01

The paper summarises the refereed contributions of seven articles reviewed for publication in the IJETP - Special Issue on 'Reactive compensation for wind farms'. The main goal of the special issue is to provide a forum to exchange information on the reactive power compensation requirements for wind farms and introducing possible price mechanisms for today's deregulated power industry. Uncompensated reactive power causes stress on the hosting utility grid as well as added expenses, which create in difficulties for power purchasing agreements from independent wind energy producers. Wind power producers need to comply with the hosting utility grid interconnection standards, e.g., voltage and frequency, as well as to provide controllable active and reactive sources of power. Active power supply is mainly dependent on the potential of wind power produced and the turbine design. Reactive power demand on the other hand depends on the conversion devices and the recovered power quantity fed to the grid. Static Var Compensators (SVC), Unified Power Quality Conditioners (UPQC), Unified Power Flow Controllers (UPFC), and the Distributed Static Synchronous Compensators (DSTATCOM) are all new emerging devices aimed at regulating the reactive power requirements. The excellent controllability of these devices has paved the way to flexible and dynamic controllers that are capable of regulating the flow of active and reactive power components. These devices are now suggested for the control of the reactive power requirement of wind generators. Studies have demonstrated acceptable voltage stabilisation results. This has increased the penetration level of wind power into existing distribution networks in many countries. (Author)

[Amnioinfusion: techniques, indications, and controlled retrospective study of 55 cases].

Science.gov (United States)

Gramellini, D; Fieni, S; Piantelli, G; Faiola, S; Kaihura, C; Verrotti, C; Cavallotti, D; Viola, P; Bacchini, G; Vadora, E

2000-01-01

Amnioinfusion is a relatively recent procedure introduced among fetal medicine techniques. Its applications focus on two different methods: transcervical and transabdominal. The first procedure usually is carried out during "intrapartum amnioinfusion" to prevent or treat fetal heart rate (FHR) decelerations related to oligohydramnios or to dilute thick meconium staining of the amniotic fluid. The latter method used during "antepartum amnioinfusion" is usually indicated for severe oligohydramnios in order to avoid the complications related such as pulmonary hypoplasia, deforming effects of oligohydramnios, variable FHR decelerations and intraventricular hemorrhages. Antepartum amnioinfusion, also used to improve ultrasound visualisation in presence of oligohydramnios, is less employed as compared to intrapartum amnioinfusion, therefore its risks are not well established. In order to study possible adverse effects on the mother or foetus, fifty five patients affected by oligohydramnios at 17th-34th week of gestational age were submitted to antepartum amnioinfusion (1-5 procedures) and were matched retrospectively with forty seven women with the same characteristics treated with the conservative and expectant management. The trend of pregnancy was the same for both groups in relation to maternal fever > 38 degrees (10.9% in the amnioinfused group vs 17.0% in control group ns), leukocyte count > 18,000/mm3 (25.5% vs 21.3%, ns), C-reactive protein > 10 ng/ml (10.9% vs 6.4%, ns). The latency period between admission and delivery was significantly longer in the amnioinfused group than in the control one [21 (range 1-98) vs 9 days (range 0-72); p amnioinfused group than in the control group (32.3% vs 66.6%; p amnioinfusion seems to increase the latency period between premature rupture of membranes and delivery, but it remains to clarify if this procedure is as much safe for the fetus as for the mother.

Active noise control technique and its application on ships

Directory of Open Access Journals (Sweden)

CHEN Kean

2017-08-01

Full Text Available Due to the rapid development during past three decades, Active Noise Control(ANC has become a highly complementary noise control approach in comparison with traditional approaches, and has formed a complete system including basic theory, investigation approach, key techniques and system implementation. Meanwhile, substantial progress has been achieved in such fields as the practical application, industrialization development and commercial popularization of ANC, and this developed technique provides a practical and feasible choice for the active control of ship noise. In this review paper, its sound field analysis, system setup and key techniques are summarized, typical examples of ANC-based engineering applications including control of cabin noise and duct noise are briefly described, and a variety of forefronts and problems associated with the applications of ANC in ship noise control, such as active sound absorption, active sound insulation and smart acoustic structure, are subsequently discussed.

Potential impact of reactive vaccination in controlling cholera outbreaks: an exploratory analysis using a Zimbabwean experience.

Science.gov (United States)

Kim, Sun-Young; Choi, Yeongchull; Mason, Peter R; Rusakaniko, Simbarashe; Goldie, Sue J

2011-09-05

To contain ongoing cholera outbreaks, the World Health Organization has suggested that reactive vaccination should be considered in addition to its previous control measures. To explore the potential impact of a hypothetical reactive oral cholera vaccination using the example of the recent large-scale cholera outbreak in Zimbabwe. This was a retrospective cost-effectiveness analysis calculating the health and economic burden of the cholera outbreak in Zimbabwe with and without reactive vaccination. The primary outcome measure was incremental cost per disability-adjusted life year (DALY) averted. Under the base-case assumptions (assuming 50% coverage among individuals aged ≥2 years), reactive vaccination could have averted 1 320 deaths and 23 650 DALYs. Considering herd immunity, the corresponding values would have been 2 920 deaths and 52 360 DALYs averted. The total vaccination costs would have been ~$74 million and ~$21 million, respectively, with per-dose vaccine price of US$5 and $1. The incremental costs per DALY averted of reactive vaccination were $2 770 and $370, respectively, for vaccine price set at $5 and $1. Assuming herd immunity, the corresponding cost was $980 with vaccine price of $5, and the programme was cost-saving with a vaccine price of $1. Results were most sensitive to case-fatality rate, per-dose vaccine price, and the size of the outbreak. Reactive vaccination has the potential to be a cost-effective measure to contain cholera outbreaks in countries at high risk. However, the feasibility of implementation should be further evaluated, and caution is warranted in extrapolating the findings to different settings in the absence of other in-depth studies.

Reactivity monitoring during reactor-reloading operations

International Nuclear Information System (INIS)

Baumann, N.P.; Ahlfeld, C.F.; Ridgely, G.C.

1983-01-01

At the Savannah River Plant (SRP) reloading operations during shutdown present special considerations in reactivity monitoring and control. Large reactivity changes may occur during reloading operations because of the heterogeneous nature of some core designs. This paper describes an improved monitoring system

Estimation of reactive power sources dynamic limits for Volt / VAr control

International Nuclear Information System (INIS)

Orozco Alvarado, Juan Jose

2013-01-01

A generic model of capacity curves is obtained from the theoretical capacity curves of the distribution generators and reactive compensation elements. The obtained generic model is structured in a simplified method of points, taking eight strategic points of two detailed curves of a generator and through a series of interpolations, achieving the estimation of limits of capacity of delivery / consumption of the generator. The theory of electric generation elements and reactive power compensation is reviewed. The curves of capacity 'Reactive Power / Active Power' are achieved for different values of tension: from wind generators with complete converter and doubly fed, photovoltaic generators with inverter and synchronous generators. The 'Reactive Power / Line Tension' capacity curves are acquired from static var compensators (SVC). The generic limits of generators and SVC are estimated from the capacity curves [es

Abstract interpretation of reactive systems : preservation of CTL*

NARCIS (Netherlands)

Dams, D.; Grumberg, O.; Gerth, R.

The advent of ever more complex reactive systems in increasingly critical areas calls for the development of automated verification techniques. Model checking is one such technique, which has proven quite successful. However, the state explosion problem remains the stumbling block in many

Object oriented programming techniques applied to device access and control

International Nuclear Information System (INIS)

Goetz, A.; Klotz, W.D.; Meyer, J.

1992-01-01

In this paper a model, called the device server model, has been presented for solving the problem of device access and control faced by all control systems. Object Oriented Programming techniques were used to achieve a powerful yet flexible solution. The model provides a solution to the problem which hides device dependancies. It defines a software framework which has to be respected by implementors of device classes - this is very useful for developing groupware. The decision to implement remote access in the root class means that device servers can be easily integrated in a distributed control system. A lot of the advantages and features of the device server model are due to the adoption of OOP techniques. The main conclusion that can be drawn from this paper is that 1. the device access and control problem is adapted to being solved with OOP techniques, 2. OOP techniques offer a distinct advantage over traditional programming techniques for solving the device access problem. (J.P.N.)

Estimation of time-varying reactivity by the H∞ optimal linear filter

International Nuclear Information System (INIS)

Suzuki, Katsuo; Shimazaki, Junya; Watanabe, Koiti

1995-01-01

The problem of estimating the time-varying net reactivity from flux measurements is solved for a point reactor kinetics model using a linear filtering technique in an H ∞ settings. In order to sue this technique, an appropriate dynamical model of the reactivity is constructed that can be embedded into the reactor model as one of its variables. A filter, which minimizes the H ∞ norm of the estimation error power spectrum, operates on neutron density measurements corrupted by noise and provides an estimate of the dynamic net reactivity. Computer simulations are performed to reveal the basic characteristics of the H ∞ optimal filter. The results of the simulation indicate that the filter can be used to determine the time-varying reactivity from neutron density measurements that have been corrupted by noise

Ionic Liquids: Radiation Chemistry, Solvation Dynamics and Reactivity Patterns

International Nuclear Information System (INIS)

Wishart, J.F.

2011-01-01

Ionic liquids (ILs) are a rapidly expanding family of condensed-phase media with important applications in energy production, nuclear fuel and waste processing, improving the efficiency and safety of industrial chemical processes, and pollution prevention. ILs generally have low volatilities and are combustion-resistant, highly conductive, recyclable and capable of dissolving a wide variety of materials. They are finding new uses in chemical synthesis, catalysis, separations chemistry, electrochemistry and other areas. Ionic liquids have dramatically different properties compared to conventional molecular solvents, and they provide a new and unusual environment to test our theoretical understanding of primary radiation chemistry, charge transfer and other reactions. We are interested in how IL properties influence physical and dynamical processes that determine the stability and lifetimes of reactive intermediates and thereby affect the courses of reactions and product distributions. We study these issues by characterization of primary radiolysis products and measurements of their yields and reactivity, quantification of electron solvation dynamics and scavenging of electrons in different states of solvation. From this knowledge we wish to learn how to predict radiolytic mechanisms and control them or mitigate their effects on the properties of materials used in nuclear fuel processing, for example, and to apply IL radiation chemistry to answer questions about general chemical reactivity in ionic liquids that will aid in the development of applications listed above. Very early in our radiolysis studies it became evident that the slow solvation dynamics of the excess electron in ILs (which vary over a wide viscosity range) increase the importance of pre-solvated electron reactivity and consequently alter product distributions and subsequent chemistry. This difference from conventional solvents has profound effects on predicting and controlling radiolytic yields

A randomized controlled trial to test the effect of multispecies probiotics on cognitive reactivity to sad mood.

Science.gov (United States)

Steenbergen, Laura; Sellaro, Roberta; van Hemert, Saskia; Bosch, Jos A; Colzato, Lorenza S

2015-08-01

Recent insights into the role of the human microbiota in cognitive and affective functioning have led to the hypothesis that probiotic supplementation may act as an adjuvant strategy to ameliorate or prevent depression. Heightened cognitive reactivity to normal, transient changes in sad mood is an established marker of vulnerability to depression and is considered an important target for interventions. The present study aimed to test if a multispecies probiotic containing Bifidobacterium bifidum W23, Bifidobacterium lactis W52, Lactobacillus acidophilus W37, Lactobacillus brevis W63, Lactobacillus casei W56, Lactobacillus salivarius W24, and Lactococcus lactis (W19 and W58) may reduce cognitive reactivity in non-depressed individuals. In a triple-blind, placebo-controlled, randomized, pre- and post-intervention assessment design, 20 healthy participants without current mood disorder received a 4-week probiotic food-supplement intervention with the multispecies probiotics, while 20 control participants received an inert placebo for the same period. In the pre- and post-intervention assessment, cognitive reactivity to sad mood was assessed using the revised Leiden index of depression sensitivity scale. Compared to participants who received the placebo intervention, participants who received the 4-week multispecies probiotics intervention showed a significantly reduced overall cognitive reactivity to sad mood, which was largely accounted for by reduced rumination and aggressive thoughts. These results provide the first evidence that the intake of probiotics may help reduce negative thoughts associated with sad mood. Probiotics supplementation warrants further research as a potential preventive strategy for depression. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Critical experiment tests of bowing and expansion reactivity calculations for LMRS

International Nuclear Information System (INIS)

Schaefer, R.W.

1988-01-01

Experiments done in several LMR-type critical assemblies simulated core axial expansion, core radial expansion and bowing, coolant expansion, and control driveline expansion. For the most part new experimental techniques were developed to do these experiments. Calculations of the experiments basically used design-level methods, except when it was necessary to investigate complexities peculiar to the experiments. It was found that these feedback reactivities generally are overpredicted, but the predictions are within 30% of the experimental values. 14 refs., 2 figs., 4 tabs

Cue-reactivity in behavioral addictions: A meta-analysis and methodological considerations.

Science.gov (United States)

Starcke, Katrin; Antons, Stephanie; Trotzke, Patrick; Brand, Matthias

2018-05-23

Background and aims Recent research has applied cue-reactivity paradigms to behavioral addictions. The aim of the current meta-analysis is to systematically analyze the effects of learning-based cue-reactivity in behavioral addictions. Methods The current meta-analysis includes 18 studies (29 data sets, 510 participants) that have used a cue-reactivity paradigm in persons with gambling (eight studies), gaming (nine studies), or buying (one study) disorders. We compared subjective, peripheral physiological, electroencephal, and neural responses toward addiction-relevant cues in patients versus control participants and toward addiction-relevant cues versus control cues in patients. Results Persons with behavioral addictions showed higher cue-reactivity toward addiction-relevant cues compared with control participants: subjective cue-reactivity (d = 0.84, p = .01) and peripheral physiological and electroencephal measures of cue-reactivity (d = 0.61, p buying disorders also showed higher cue-reactivity toward addiction-relevant cues compared with control cues: subjective cue-reactivity (d = 0.39, p = .11) and peripheral physiological and electroencephal measures of cue-reactivity (d = 0.47, p = .05). Increased neural activation was found in the caudate nucleus, inferior frontal gyrus, angular gyrus, inferior network, and precuneus. Discussion and conclusions Cue-reactivity not only exists in substance-use disorders but also in gambling, gaming, and buying disorders. Future research should differentiate between cue-reactivity in addictive behaviors and cue-reactivity in functional excessive behaviors such as passions, hobbies, or professions.

Neural correlates of reactive aggression in children with attention-deficit/hyperactivity disorder and comorbid disruptive behaviour disorders

DEFF Research Database (Denmark)

Bubenzer-Busch, Sarah; Herpertz-Dahlmann, Beate; Kuzmanovic, B

2016-01-01

ObjectiveAttention deficit hyperactivity disorder (ADHD) is often linked with impulsive and aggressive behaviour, indexed by high comorbidity rates between ADHD and disruptive behaviour disorders (DBD). The present study aimed to investigate underlying neural activity of reactive aggression...... in children with ADHD and comorbid DBD using functional neuroimaging techniques (fMRI). MethodEighteen boys with ADHD (age 9-14years, 10 subjects with comorbid DBD) and 18 healthy controls were administered a modified fMRI-based version of the Point Subtraction Aggression Game' to elicit reactive aggressive...... activation of regions belonging to the insula and the middle temporal sulcus. ConclusionData support the hypothesis that deficient inhibitory control mechanisms are related to increased impulsive aggressive behaviour in young people with ADHD and comorbid DBD....

Research review: Indoor air quality control techniques

International Nuclear Information System (INIS)

Fisk, W.J.

1986-10-01

Techniques for controlling the concentration of radon, formaldehyde, and combustion products in the indoor air are reviewed. The most effective techniques, which are generally based on limiting or reducing indoor pollutant source strengths, can decrease indoor pollutant concentrations by a factor of 3 to 10. Unless the initial ventilation rate is unusually low, it is difficult to reduce indoor pollutant concentrations more than approximately 50% by increasing the ventilation rate of an entire building. However, the efficiency of indoor pollutant control by ventilation can be enhanced through the use of local exhaust ventilation near concentrated sources of pollutants, by minimizing short circuiting of air from supply to exhaust when pollutant sources are dispersed and, in some situations, by promoting a displacement flow of air and pollutants toward the exhaust. Active air cleaning is also examined briefly. Filtration and electrostatic air cleaning for removal of particles from the indoor air are the most practical and effective currently available techniques of air cleaning. 49 refs., 7 figs

Development of a UNIX network compatible reactivity computer

International Nuclear Information System (INIS)

Sanchez, R.F.; Edwards, R.M.

1996-01-01

A state-of-the-art UNIX network compatible controller and UNIX host workstation with MATLAB/SIMULINK software were used to develop, implement, and validate a digital reactivity calculation. An objective of the development was to determine why a Macintosh-based reactivity computer reactivity output drifted intolerably

National supply of reactivity control rods for Embalse nuclear power plant (CNE)

International Nuclear Information System (INIS)

Biondo, C.D.; Carloni, J.G.; Aba, J.A.

1987-01-01

The manufacture and supply on industrial scale of reactivity control rods for CNE (Embalse nuclear power plant) were developed by the National Atomic Energy Commission (CNEA) together with the private industry, as part of a program aimed to the substitution of imported supplies used in the operation of power plants by materials manufactured in Argentina. So far, the control rods were imported from Canada. In this work, the different development stages performed by CNEA and CONUAR S.A. are described, leading to the supply of a set of 21 cobalt rods to be included in a reactor of CNE in order to qualify this component. Among the main activities performed, the following stand out: specifications development, particularly those concerning to cobalt cores, evaluation of design documentation and elaboration of bidding conditions and a plan of manufacture and control. According to the results obtained during the service and the post-irradiation measurements, the design will be reviewed in order to undertake new manufacturing plans. (Author)

Selective weed control using laser techniques

OpenAIRE

Marx, Christian; Pastrana-Perez, Julio; Hustedt, Michael; Barcikowski, Stephan; Haferkamp, Heinz; Rath, Thomas

2012-01-01

This contribution discusses technical and growth relevant aspects of using laser techniques for weed control. The research on thermal weed control via laser first focused on the interaction of laser beams and weed plants. Due to preliminary studies, a CO2-laser was selected for further studies with regard to the process factors laser energy, laser spot area, coverage of the weeds meristem, weed species (Amaranthus retroflexus), and weed growth stage. Thereby, the laser damage was modeled in o...

Auditory orientation in crickets: Pattern recognition controls reactive steering

Science.gov (United States)

Poulet, James F. A.; Hedwig, Berthold

2005-10-01

Many groups of insects are specialists in exploiting sensory cues to locate food resources or conspecifics. To achieve orientation, bees and ants analyze the polarization pattern of the sky, male moths orient along the females' odor plume, and cicadas, grasshoppers, and crickets use acoustic signals to locate singing conspecifics. In comparison with olfactory and visual orientation, where learning is involved, auditory processing underlying orientation in insects appears to be more hardwired and genetically determined. In each of these examples, however, orientation requires a recognition process identifying the crucial sensory pattern to interact with a localization process directing the animal's locomotor activity. Here, we characterize this interaction. Using a sensitive trackball system, we show that, during cricket auditory behavior, the recognition process that is tuned toward the species-specific song pattern controls the amplitude of auditory evoked steering responses. Females perform small reactive steering movements toward any sound patterns. Hearing the male's calling song increases the gain of auditory steering within 2-5 s, and the animals even steer toward nonattractive sound patterns inserted into the speciesspecific pattern. This gain control mechanism in the auditory-to-motor pathway allows crickets to pursue species-specific sound patterns temporarily corrupted by environmental factors and may reflect the organization of recognition and localization networks in insects. localization | phonotaxis

Assessment of CANDU-6 reactivity devices for DUPIC fuel

International Nuclear Information System (INIS)

Jeong, Chang Joon; Choi, Hang Bok

1998-11-01

Reactivity device characteristics for a CANDU 6 reactor loaded with DUPIC fuel have been assessed. The lattice parameters were generated by WIMS-AECL code and the core calculations were performed by RFSP code with a 3-dimensional full core model. The reactivity devices studied are the zone controller, adjusters, mechanical control absorber and shutoff rods. For the zone controller system, damping capability for spatial oscillation was investigated. For the adjusters, the restart capability was investigated. For the adjusters, the restart capability was investigated. The shin operation and power stepback calculation were also performed to confirm the compatibility of the current adjuster system. The mechanical control absorber was assessed for the function of compensating temperature reactivity feedback following a power reduction. And shutoff rods were also assessed to investigate the following a power reduction. And shutoff rods were also assessed to investigate the static reactivity worth. This study has shown that the current reactivity device system of CANDU-6 core with the DUPIC fuel. (author). 9 refs., 17 tabs., 7 figs

Advanced analytical techniques for boiling water reactor chemistry control

Energy Technology Data Exchange (ETDEWEB)

Alder, H P; Schenker, E [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-02-01

The analytical techniques applied can be divided into 5 classes: OFF-LINE (discontinuous, central lab), AT-LINE (discontinuous, analysis near loop), ON-LINE (continuous, analysis in bypass). In all cases pressure and temperature of the water sample are reduced. In a strict sense only IN-LINE (continuous, flow disturbance) and NON-INVASIVE (continuous, no flow disturbance) techniques are suitable for direct process control; - the ultimate goal. An overview of the analytical techniques tested in the pilot loop is given. Apart from process and overall water quality control, standard for BWR operation, the main emphasis is on water impurity characterization (crud particles, hot filtration, organic carbon); on stress corrosion crackling control for materials (corrosion potential, oxygen concentration) and on the characterization of the oxide layer on austenites (impedance spectroscopy, IR-reflection). The above mentioned examples of advanced analytical techniques have the potential of in-line or non-invasive application. They are different stages of development and are described in more detail. 28 refs, 1 fig., 5 tabs.

Moderate alcohol consumption reduces plasma C-reactive protein and fibrinogen levels : a randomized, diet-controlled intervention study

NARCIS (Netherlands)

Sierksma, A.; Gaag, M.S. van der; Kluft, C.; Hendriks, H.F.J.

2002-01-01

Objective: To evaluate the effect of moderate alcohol consumption on the acute phase proteins C-reactive protein and fibrinogen. Design: Randomized, diet-controlled, cross-over study. Setting: The study was performed at TNO Nutrition and Food Research, Zeist, The Netherlands. Subjects: Ten

On the deposition parameters of indium oxide (IO) and tin oxide (TO) by reactive evaporation technique

International Nuclear Information System (INIS)

Hassan, F.; Abdullah, A.H.; Salam, R.

1990-01-01

Thin films of tin oxide (TO) and indium oxide (IO) are prepared by the reactive evaporation technique, where indium or tin sources are evaporated and made to react with oxygen gas injected close to the substrate. In both depositions a substrate temperature of 380 0 C and a chamber pressure of 2x10 -5 mbar are utilized, but however different oxygen flow rates has been maintained. For TO, the deposition rate is found to be constant up to about 55 minutes of deposition time with a deposition rate of about 0.10 A/s, but for longer deposition time the deposition rate increases rapidly up to about 0.30 A/s. The IO displays a higher deposition rate of about 0.80 A/s over a deposition time 30 minutes, beyond which the deposition rate increases gradually

Contributions to fuzzy polynomial techniques for stability analysis and control

OpenAIRE

Pitarch Pérez, José Luis

2014-01-01

The present thesis employs fuzzy-polynomial control techniques in order to improve the stability analysis and control of nonlinear systems. Initially, it reviews the more extended techniques in the field of Takagi-Sugeno fuzzy systems, such as the more relevant results about polynomial and fuzzy polynomial systems. The basic framework uses fuzzy polynomial models by Taylor series and sum-of-squares techniques (semidefinite programming) in order to obtain stability guarantees...

Qualitative performance comparison of reactivity estimation between the extended Kalman filter technique and the inverse point kinetic method

International Nuclear Information System (INIS)

Shimazu, Y.; Rooijen, W.F.G. van

2014-01-01

Highlights: • Estimation of the reactivity of nuclear reactor based on neutron flux measurements. • Comparison of the traditional method, and the new approach based on Extended Kalman Filtering (EKF). • Estimation accuracy depends on filter parameters, the selection of which is described in this paper. • The EKF algorithm is preferred if the signal to noise ratio is low (low flux situation). • The accuracy of the EKF depends on the ratio of the filter coefficients. - Abstract: The Extended Kalman Filtering (EKF) technique has been applied for estimation of subcriticality with a good noise filtering and accuracy. The Inverse Point Kinetic (IPK) method has also been widely used for reactivity estimation. The important parameters for the EKF estimation are the process noise covariance, and the measurement noise covariance. However the optimal selection is quite difficult. On the other hand, there is only one parameter in the IPK method, namely the time constant for the first order delay filter. Thus, the selection of this parameter is quite easy. Thus, it is required to give certain idea for the selection of which method should be selected and how to select the required parameters. From this point of view, a qualitative performance comparison is carried out

Robust intelligent backstepping tracking control for uncertain non-linear chaotic systems using H∞ control technique

International Nuclear Information System (INIS)

Peng, Y.-F.

2009-01-01

The cerebellar model articulation controller (CMAC) is a non-linear adaptive system with built-in simple computation, good generalization capability and fast learning property. In this paper, a robust intelligent backstepping tracking control (RIBTC) system combined with adaptive CMAC and H ∞ control technique is proposed for a class of chaotic systems with unknown system dynamics and external disturbance. In the proposed control system, an adaptive backstepping cerebellar model articulation controller (ABCMAC) is used to mimic an ideal backstepping control (IBC), and a robust H ∞ controller is designed to attenuate the effect of the residual approximation errors and external disturbances with desired attenuation level. Moreover, the all adaptation laws of the RIBTC system are derived based on the Lyapunov stability analysis, the Taylor linearization technique and H ∞ control theory, so that the stability of the closed-loop system and H ∞ tracking performance can be guaranteed. Finally, three application examples, including a Duffing-Holmes chaotic system, a Genesio chaotic system and a Sprott circuit system, are used to demonstrate the effectiveness and performance of proposed robust control technique.

Operating control techniques for maglev transport systems

Energy Technology Data Exchange (ETDEWEB)

Kraft, K H; Schnieder, E

1984-06-01

The technical and operational possibilities of magnetic levitation transport systems can only be fully exploited by introducing 'intelligent' control systems which ensure automatic and trouble-free train running. The solution of exacting requirements in the fields of traction dynamics, security and control as well as information gathering transmission and processing is an important prior condition in that respect. The authors report here on the present state of research and development in operating control techniques applicable to maglev transport systems.

Synthesis and processing of composites by reactive metal penetration

Energy Technology Data Exchange (ETDEWEB)

Loehman, R.E.; Ewsuk, K.G. [Sandia National Labs., Albuquerque, NM (United States); Tomsia, A.P. [Pask Research and Engineering, Berkeley, CA (United States)] [and others

1997-04-01

Achieving better performance in commercial products and processes often is dependent on availability of new and improved materials. Ceramic-metal composites have advantages over more conventional materials because of their high stiffness-to-weight ratios, good fracture toughness, and because their electrical and thermal properties can be varied through control of their compositions and microstructures. However, ceramic composites will be more widely used only when their costs are competitive with other materials and when designers have more confidence in their reliability. Over the past four years reactive metal penetration has been shown to be a promising technique for making ceramic and metal-matrix composites to near-net-shape with control of both composition and microstructure. It appears that, with sufficient development, reactive metal penetration could be an economical process for manufacturing many of the advanced ceramic composites that are needed for light-weight structural and wear applications for transportation and energy conversion devices. Near-net-shape fabrication of parts is a significant advantage because costly and energy intensive grinding and machining operations are substantially reduced, and the waste generated from such finishing operations is minimized. The most promising compositions to date consist of Al and Al{sub 2}O{sub 3}; thus, these composites should be of particular interest to the aluminum industry. The goals of this ceramic-metal composite research and development program are: (1) to identify compositions favorable for making composites by reactive metal penetration; (2) to understand the mechanism(s) by which these composites are formed; (3) to control and optimize the process so that composites and composite coatings can be made economically; and (4) to apply R&D results to problems of interest to the aluminum industry.

A new algorithm for optimum voltage and reactive power control for minimizing transmission lines losses

International Nuclear Information System (INIS)

Ghoudjehbaklou, H.; Danai, B.

2001-01-01

Reactive power dispatch for voltage profile modification has been of interest to power utilities. Usually local bus voltages can be altered by changing generator voltages, reactive shunts, ULTC transformers and SVCs. Determination of optimum values for control parameters, however, is not simple for modern power system networks. Heuristic and rather intelligent algorithms have to be sought. In this paper a new algorithm is proposed that is based on a variant of a genetic algorithm combined with simulated annealing updates. In this algorithm a fuzzy multi-objective a approach is used for the fitness function of the genetic algorithm. This fuzzy multi-objective function can efficiently modify the voltage profile in order to minimize transmission lines losses, thus reducing the operating costs. The reason for such a combination is to utilize the best characteristics of each method and overcome their deficiencies. The proposed algorithm is much faster than the classical genetic algorithm and cna be easily integrated into existing power utilities software. The proposed algorithm is tested on an actual system model of 1284 buses, 799 lines, 1175 fixed and ULTC transformers, 86 generators, 181 controllable shunts and 425 loads

Reliability of techniques used in the diagnosis of canine visceral leishmaniasis by the national control program in Brazil: A survey in an area of recent transmission.

Science.gov (United States)

Belo, Vinícius Silva; Gregório, Eliana Aparecida; Teixeira-Neto, Rafael Gonçalves; da Rocha Lima, Ana Cristina Vianna Mariano; Pereira, Agnes Antônia Sampaio; Marcelino, Andreza Pain; Paz, Gustavo Fontes; da Silva, Eduardo Sérgio

2017-10-01

One of the key components of the Brazilian Program for the Control of Visceral Leishmaniasis (PCLV) is the euthanasia of Leishmania-infected canine reservoirs, the detection of which depends on a screening procedure involving a Dual Path Platform ® (DPP) immunoassay and a confirmatory enzyme-linked immunosorbent assay (ELISA). The aims of the present study were to evaluate the reliability of these techniques in a region of recent transmission of canine VL, to follow up the seroconversion 3-4 months after the initial diagnosis of DPP reactive but ELISA indeterminate or non-reactive dogs, and to identify the species of Leishmania in circulation in the area. Each animal was submitted to DPP under field conditions, performed by municipal health workers using peripheral blood (DPP-field), to DPP under laboratory conditions using serum (DPP-lab) and to ELISA using serum. The agreements between the tests were determined using McNemar's χ 2 test, Cohen's kappa coefficient (k) at the 95% confidence interval and prevalence-adjusted bias-adjusted kappa (PABAK). Of the 1130 dogs examined, 74.2% were non-reactive in all three tests applied. Based on the PCLV positive-infection criterion, seroprevalence was 8.9% (101/1130) with 83.2% (84/101) of infected animals showing reactivity in all three tests while 7.8% (8/101) were reactive in DPP-field and ELISA and 8.9% (9/101) in DPP-lab and ELISA. The proportions of disagreements were substantial in all comparisons. Inter-rater reliability between DPP-field and ELISA (k=0.55; PABAK=0.78) and DPP-lab and ELISA (k=0.59; PABAK=0.81) were considered moderate, while that between DPP-field and DPP-lab (k=0.61; PABAK=0.79) was classified as marginally good. The proportion of seroconversions in DPP reactive animals that were initially ELISA indeterminate was significantly higher than in those that were DPP reactive but initially ELISA non-reactive. Restriction fragment length polymorphism analysis revealed the presence of Leishmania

Overweight and Cognitive Performance: High Body Mass Index Is Associated with Impairment in Reactive Control during Task Switching

Directory of Open Access Journals (Sweden)

Laura Steenbergen

2017-10-01

Full Text Available The prevalence of weight problems is increasing worldwide. There is growing evidence that high body mass index (BMI is associated with frontal lobe dysfunction and deficits in cognitive control. The present study aims to clarify the association between weight status and the degree of impairment in cognitive flexibility, i.e., the ability to efficiently switch from one task to another, by disentangling the preparatory and residual domains of task switching. Twenty-six normal weight (BMI < 25, five males and twenty-six overweight (BMI ≥ 25, seven males university students performed a task-switching paradigm that provides a relatively well-established diagnostic measure of proactive vs. reactive control with regard to cognitive flexibility. Compared to individuals with a BMI lower than 25, overweight (i.e., ≥25 was associated with increased switching costs in the reactive switching condition (i.e., when preparation time is short, representing reduced cognitive flexibility in the preparatory domain. In addition, the overweight group reported significantly more depression and binge eating symptoms, although still indicating minimal depression. No between-group differences were found with regard to self-reported autism spectrum symptoms, impulsiveness, state- and trait anxiety, and cognitive reactivity to depression. The present findings are consistent with and extend previous literature showing that elevated BMI in young, otherwise healthy individuals is associated with significantly more switching costs due to inefficiency in the retrieval, implementation, and maintenance of task sets, indicating less efficient cognitive control functioning.

Identification of a B cell-dependent subpopulation of multiple sclerosis by measurements of brain-reactive B cells in the blood.

Science.gov (United States)

Kuerten, Stefanie; Pommerschein, Giovanna; Barth, Stefanie K; Hohmann, Christopher; Milles, Bianca; Sammer, Fabian W; Duffy, Cathrina E; Wunsch, Marie; Rovituso, Damiano M; Schroeter, Michael; Addicks, Klaus; Kaiser, Claudia C; Lehmann, Paul V

2014-01-01

B cells are increasingly coming into play in the pathogenesis of multiple sclerosis (MS). Here, we screened peripheral blood mononuclear cells (PBMC) from patients with clinically isolated syndrome (CIS), MS, other non-inflammatory neurological, inflammatory neurological or autoimmune diseases, and healthy donors for their B cell reactivity to CNS antigen using the enzyme-linked immunospot technique (ELISPOT) after 96 h of polyclonal stimulation. Our data show that nine of 15 patients with CIS (60.0%) and 53 of 67 patients with definite MS (79.1%) displayed CNS-reactive B cells, compared to none of the control donors. The presence of CNS-reactive B cells in the blood of the majority of patients with MS or at risk to develop MS along with their absence in control subjects suggests that they might be indicative of a B cell-dependent subpopulation of the disease. Copyright © 2014. Published by Elsevier Inc.

Analysis of the Techniques for Measuring the Reactivity of Far Sub-Critical Multiplying Systems

International Nuclear Information System (INIS)

Vandeplas, P.

1968-01-01

The methods of measuring control-rod worth on the basis of reactor response to a periodic excitation source are analysed and it is shown that the ratio of the integrals of the prompt and delayed neutron densities over one period is independent of the shape of the signal used. This ratio will thus be equal to the ratio of the neutron densities in the presence of a time-independent source. The pulsed source, sinusoidal source and source removed methods therefore give identical worth values. Experimentation and numerical analysis show that the ratio of prompt to delayed neutron density, which is a linear combination of successive eigenvalues of the system, is largely dependent on the position of the source. It is demonstrated analytically that with a suitably chosen volume of integration, the contribution of the space harmonics is drastically reduced in the integrals of both the prompt neutron density and the delayed neutron density. Numerical studies show that the ratio of these two integrals is practically equal to the reactivity corresponding to the fundamental static mode and is almost independent of the position of the source. Integration of the neutron densities over a volume can be reduced to an integration along a straight line by a suitable choice of source location. Such an integration can be performed by means of an integral detector, thereby only requiring one measurement. Optimization of the position of the source and of the limits of integration to give the best value for the reactivity can be achieved on the basis of purely experimental criteria. (author) [fr

Synthesis and characterization of porous crystalline SiC thin films prepared by radio frequency reactive magnetron sputtering technique

Energy Technology Data Exchange (ETDEWEB)

Qamar, Afzaal, E-mail: afzaalqamar@gmail.com [Department of Physics and Applied Mathematics, PIEAS, Nilore, Islamabad, Punjab 42600 (Pakistan); Mahmood, Arshad [National Institute of Laser and Optronics, Nilore, Islamabad (Pakistan); Sarwar, Tuba; Ahmed, Nadeem [Department of Physics and Applied Mathematics, PIEAS, Nilore, Islamabad, Punjab 42600 (Pakistan)

2011-05-15

Hexagonal SiC thin films have been deposited using radio frequency reactive magnetron sputtering technique by varying the substrate temperature and other deposition conditions. Prior to deposition surface modification of the substrate Si(1 0 0) played an important role in deposition of the hexagonal SiC structure. The effect of substrate temperature during deposition on structure, composition and surface morphology of the SiC films has been analyzed using atomic force microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry. X-ray diffraction in conventional {theta}-2{theta} mode and omega scan mode revealed that the deposited films were crystalline having 8H-SiC structure and crystallinity improved with increase of deposition temperature. The bonding order and Si-C composition within the films showed improvement with the increase of deposition temperature. The surface of thin films grew in the shape of globes and columns depending upon deposition temperature. The optical properties also showed improvement with increase of deposition temperature and the results obtained by ellipsometry reinforced the results of other techniques.

MP98, an innovative reactivity control system for LWR and VHTR, tests results on prototypes

International Nuclear Information System (INIS)

Emin, M.; Gagne, J.F.

2005-01-01

MP98' Reactivity Control System is now a technology tested on a real scale prototypes. Demonstrator is working at PWR real conditions (155 bars, 320 degree C), and many accidents configurations could be simulated. This paper presents the technology, describes the demonstrator design and presents some results. Mock up and demonstrator have permitted to optimize the design of MP98' devices to prepare industrialization. (authors)

Backstepping Based Formation Control of Quadrotors with the State Transformation Technique

Directory of Open Access Journals (Sweden)

Keun Uk Lee

2017-11-01

Full Text Available In this paper, a backstepping-based formation control of quadrotors with the state transformation technique is proposed. First, the dynamics of a quadrotor is derived by using the Newton–Euler formulation. Next, a backstepping-based formation control for quadrotors using a state transformation technique is presented. In the position control, which is the basis of formation control, it is possible to derive the reference attitude angles employing a state transformation technique without the small angle assumption or the simplified dynamics usually used. Stability analysis based on the Lyapunov theorem shows that the proposed formation controller can provide a quadrotor formation error system that is asymptotically stabilized. Finally, we verify the performance of the proposed formation control method through comparison simulations.

Reactivity and structural evolution of urchin-like Co nanostructures under controlled environments.

Science.gov (United States)

Dembele, K; Moldovan, S; Hirlimann, Ch; Harmel, J; Soulantica, K; Serp, P; Chaudret, B; Gay, A-S; Maury, S; Berliet, A; Fecant, A; Ersen, O

2018-02-01

In situ transmission electron microscopy (TEM) of samples in a controlled gas environment allows for the real time study of the dynamical changes in nanomaterials at high temperatures and pressures up to the ambient pressure (10 5 Pa) with a spatial resolution close to the atomic scale. In the field of catalysis, the implementation and quantitative use of in situ procedures are fundamental for a better understanding of the behaviour of catalysts in their environments and operating conditions. By using a microelectromechanical systems (MEMS)-based atmospheric gas cell, we have studied the thermal stability and the reactivity of crystalline cobalt nanostructures with initial 'urchin-like' morphologies sustained by native surface ligands that result from their synthesis reaction. We have evidenced various behaviors of the Co nanostructures that depend on the environment used during the observations. At high temperature under vacuum or in an inert atmosphere, the migration of Co atoms towards the core of the particles is activated and leads to the formation of carbon nanostructures using as a template the initial multipods morphology. In the case of reactive environments, for example, pure oxygen, our investigation allowed to directly monitor the voids formation through the Kirkendall effect. Once the nanostructures were oxidised, it was possible to reduce them back to the metallic phase using a dihydrogen flux. Under a pure hydrogen atmosphere, the sintering of the whole structure occurred, which illustrates the high reactivity of such structures as well as the fundamental role of the present ligands as morphology stabilisers. The last type of environmental study under pure CO and syngas (i.e. a mixture of H 2 :CO = 2:1) revealed the metal particles carburisation at high temperature. © 2017 The Authors Journal of Microscopy © 2017 Royal Microscopical Society.

Appetitive Motivation and Negative Emotion Reactivity among Remitted Depressed Youth

Science.gov (United States)

Hankin, Benjamin L.; Wetter, Emily K.; Flory, Kate

2012-01-01

Depression has been characterized as involving altered appetitive motivation and emotional reactivity. Yet no study has examined objective indices of emotional reactivity when the appetitive/approach system is suppressed in response to failure to attain a self-relevant goal and desired reward. Three groups of youth (N = 98, ages 9–15; remitted depressed, n = 34; externalizing disordered without depression, n = 30, and healthy controls, n = 34) participated in a novel reward striving task designed to activate the appetitive/approach motivation system. Objective facial expressions of emotion were videotaped and coded throughout both failure (i.e., nonreward) and control (success and reward) conditions. Observational coding of facial expressions as well as youths’ subjective emotion reports showed that the remitted depressed youth specifically exhibited more negative emotional reactivity to failure in the reward striving task, but not the control condition. Neither externalizing disordered (i.e., ADHD, CD, and/ or ODD) nor control youth displayed greater negative emotional reactivity in either the failure or control condition. Findings suggest that depression among youth is related to dysregulated appetitive motivation and associated negative emotional reactivity after failing to achieve an important, self-relevant goal and not attaining reward. These deficits in reward processing appear to be specific to depression as externalizing disordered youth did not display negative emotional reactivity to failure after their appetitive motivation system was activated. PMID:22901275

Reactive chemicals and process hazards

International Nuclear Information System (INIS)

Surianarayanan, M.

2016-01-01

Exothermic chemical reactions are often accompanied by significant heat release, and therefore, need a thorough investigation before they are taken to a plant scale. Sudden thermal energy releases from exothermic decompositions and runaway reactions have contributed to serious fire and explosions in several chemical process plants. Similarly, thermal runaway had also occurred in storage and transportation of reactive chemicals. The secondary events of thermal runaway reactions can be rupture of process vessel, toxic spills and release of explosive vapor clouds or combination of these also. The explosion hazards are governed by the system thermodynamics and kinetics of the thermal process. Theoretical prediction of limiting temperature is difficult due to process complexities. Further, the kinetic data obtained through classical techniques, at conditions far away from runaway situation, is often not valid for assessing the runaway behavior of exothermic processes. The main focus of this lecture is to discuss the causes and several contributing factors for thermal runaway and instability and present analyses of the methodologies of the new instrumental techniques for assessing the thermal hazards of reactive chemicals during processing, storage and transportation. (author)

Temperature dependence of InN film deposition by an RF plasma-assisted reactive ion beam sputtering deposition technique

International Nuclear Information System (INIS)

Shinoda, Hiroyuki; Mutsukura, Nobuki

2005-01-01

Indium nitride (InN) films were deposited on Si(100) substrates using a radiofrequency (RF) plasma-assisted reactive ion beam sputtering deposition technique at various substrate temperatures. The X-ray diffraction patterns of the InN films suggest that the InN films deposited at substrate temperatures up to 370 deg C were cubic crystalline InN; and at 500 deg C, the InN film was hexagonal crystalline InN. In a scanning electron microscope image of the InN film surface, facets of cubic single-crystalline InN grains were clearly observed on the InN film deposited at 370 deg C. The inclusion of metallic indium appeared on the InN film deposited at 500 deg C

An assessment of the dual-mode reactivity controlled compression ignition/conventional diesel combustion capabilities in a EURO VI medium-duty diesel engine fueled with an intermediate ethanol-gasoline blend and biodiesel

International Nuclear Information System (INIS)

Benajes, Jesús; García, Antonio; Monsalve-Serrano, Javier; Balloul, Iyad; Pradel, Gérard

2016-01-01

Highlights: • Reactivity controlled compression ignition regime utilized from 25% to 35% load. • Dual-mode reduces the regeneration periods of the diesel particulate filter. • The use of near-term available biofuels allows good performance and emissions. • Dual-mode leads to 2% greater efficiency than diesel combustion at high engine speeds. - Abstract: This work investigates the capabilities of the dual-mode reactivity controlled compression ignition/conventional diesel combustion engine operation to cover the full operating range of a EURO VI medium-duty diesel engine with compression ratio of 17.5:1. This concept is based on covering all the engine map switching between the reactivity controlled compression ignition and the conventional diesel combustion operating modes. Specifically, the benefits of reactivity controlled compression ignition combustion are exploited whenever possible according to certain restrictions, while the conventional diesel combustion operation is used to cover the zones of the engine map in which the reactivity controlled compression ignition operation is limited. The experiments were conducted using a single-cylinder research diesel engine derived from the multi-cylinder production engine. In addition, considering the mandatory presence of biofuels in the future context of road transport and the ability of ethanol to be blended with gasoline, the low reactivity fuel used in the study is a blend of 20% ethanol by volume with 80% of 95 octane number gasoline. Moreover, a diesel containing 7% of biodiesel has been used as high reactivity fuel. Firstly, a reactivity controlled compression ignition mapping is performed to check the operational limits of the concept in this engine platform. Later, based on the results, the potential of the dual-mode concept is discussed. Results suggest that, under the constraints imposed, reactivity controlled compression ignition combustion can be utilized between 25% and 35% load. In this region

Reactivity-induced time-dependencies of EBR-II linear and non-linear feedbacks

International Nuclear Information System (INIS)

Grimm, K.N.; Meneghetti, D.

1988-01-01

Time-dependent linear feedback reactivities are calculated for stereotypical subassemblies in the EBR-II reactor. These quantities are calculated from nodal reactivities obtained from a kinetic code analysis of an experiment in which the change in power resulted from the dropping of a control rod. Shown with these linear reactivities are the reactivity associated with the control-rod shaft contraction and also time-dependent non-linear (mainly bowing) component deduced from the inverse kinetics of the experimentally measured fission power and the calculated linear reactivities. (author)

Coolant void reactivity adjustments in advanced CANDU lattices using adjoint sensitivity technique

International Nuclear Information System (INIS)

Assawaroongruengchot, M.; Marleau, G.

2008-01-01

Coolant void reactivity (CVR) is an important factor in reactor accident analysis. Here we study the adjustments of CVR at beginning of burnup cycle (BOC) and k eff at end of burnup cycle (EOC) for a 2D Advanced CANDU Reactor (ACR) lattice using the optimization and adjoint sensitivity techniques. The sensitivity coefficients are evaluated using the perturbation theory based on the integral neutron transport equations. The neutron and flux importance transport solutions are obtained by the method of cyclic characteristics (MOCC). Three sets of parameters for CVR-BOC and k eff -EOC adjustments are studied: (1) Dysprosium density in the central pin with Uranium enrichment in the outer fuel rings, (2) Dysprosium density and Uranium enrichment both in the central pin, and (3) the same parameters as in the first case but the objective is to obtain a negative checkerboard CVR-BOC (CBCVR-BOC). To approximate the EOC sensitivity coefficient, we perform constant-power burnup/depletion calculations using a slightly perturbed nuclear library and the unperturbed neutron fluxes to estimate the variation of nuclide densities at EOC. Our aim is to achieve a desired negative CVR-BOC of -2 mk and k eff -EOC of 0.900 for the first two cases, and a CBCVR-BOC of -2 mk and k eff -EOC of 0.900 for the last case. Sensitivity analyses of CVR and eigenvalue are also included in our study

Coolant void reactivity adjustments in advanced CANDU lattices using adjoint sensitivity technique

Energy Technology Data Exchange (ETDEWEB)

Assawaroongruengchot, M. [Institut de Genie Nucleaire, Ecole Polytechnique de Montreal, P.O. Box 6079, stn. Centre-ville, Montreal, H3C3A7 (Canada)], E-mail: monchaia@gmail.com; Marleau, G. [Institut de Genie Nucleaire, Ecole Polytechnique de Montreal, P.O. Box 6079, stn. Centre-ville, Montreal, H3C3A7 (Canada)], E-mail: guy.marleau@polymtl.ca

2008-03-15

Coolant void reactivity (CVR) is an important factor in reactor accident analysis. Here we study the adjustments of CVR at beginning of burnup cycle (BOC) and k{sub eff} at end of burnup cycle (EOC) for a 2D Advanced CANDU Reactor (ACR) lattice using the optimization and adjoint sensitivity techniques. The sensitivity coefficients are evaluated using the perturbation theory based on the integral neutron transport equations. The neutron and flux importance transport solutions are obtained by the method of cyclic characteristics (MOCC). Three sets of parameters for CVR-BOC and k{sub eff}-EOC adjustments are studied: (1) Dysprosium density in the central pin with Uranium enrichment in the outer fuel rings, (2) Dysprosium density and Uranium enrichment both in the central pin, and (3) the same parameters as in the first case but the objective is to obtain a negative checkerboard CVR-BOC (CBCVR-BOC). To approximate the EOC sensitivity coefficient, we perform constant-power burnup/depletion calculations using a slightly perturbed nuclear library and the unperturbed neutron fluxes to estimate the variation of nuclide densities at EOC. Our aim is to achieve a desired negative CVR-BOC of -2 mk and k{sub eff}-EOC of 0.900 for the first two cases, and a CBCVR-BOC of -2 mk and k{sub eff}-EOC of 0.900 for the last case. Sensitivity analyses of CVR and eigenvalue are also included in our study.

RSA Reactivity in Current and Remitted Major Depressive Disorder

Science.gov (United States)

Bylsma, Lauren M.; Salomon, Kristen; Taylor-Clift, April; Morris, Bethany H.; Rottenberg, Jonathan

2014-01-01

Objective Low resting respiratory sinus arrhythmia (RSA) levels and blunted RSA reactivity are thought to index impaired emotion regulation capacity. Major Depressive Disorder (MDD) has been associated with abberant RSA reactivity and recovery to a speech stressor task relative to healthy controls. Whether impaired RSA functioning reflects aspects of the depressed mood state or a stable vulnerability marker for depression is unknown. Methods We compared resting RSA and RSA reactivity between individuals with MDD (n=49), remitted depression (RMD, n=24), and healthy controls (n=45). ECG data were collected during a resting baseline, a paced-breathing baseline, and two reactivity tasks (speech stressor, cold exposure). Results A group by time quadratic effect emerged (F=4.36(2,109), p=.015) for RSA across phases of the speech stressor (baseline, instruction, preparation, speech, recovery). Follow-up analyses revealed that those with MDD uniquely exhibited blunted RSA reactivity, whereas RMD and controls both exhibited normal task-related vagal withdrawal and post-task recovery. The group by time interaction remained after covariation for age, sex, waist circumference, physical activity, and respiration, but not sleep quality. Conclusions These results provide new evidence that abberant RSA reactivity marks features that track the depressed state, such as poor sleep, rather than a stable trait evident among asymtomatic persons. PMID:24367127

Engine control techniques to account for fuel effects

Science.gov (United States)

Kumar, Shankar; Frazier, Timothy R.; Stanton, Donald W.; Xu, Yi; Bunting, Bruce G.; Wolf, Leslie R.

2014-08-26

A technique for engine control to account for fuel effects including providing an internal combustion engine and a controller to regulate operation thereof, the engine being operable to combust a fuel to produce an exhaust gas; establishing a plurality of fuel property inputs; establishing a plurality of engine performance inputs; generating engine control information as a function of the fuel property inputs and the engine performance inputs; and accessing the engine control information with the controller to regulate at least one engine operating parameter.

Spring 5 & reactive streams

CERN Multimedia

CERN. Geneva; Clozel, Brian

2017-01-01

Spring is a framework widely used by the world-wide Java community, and it is also extensively used at CERN. The accelerator control system is constituted of 10 million lines of Java code, spread across more than 1000 projects (jars) developed by 160 software engineers. Around half of this (all server-side Java code) is based on the Spring framework. Warning: the speakers will assume that people attending the seminar are familiar with Java and Spring’s basic concepts. Spring 5.0 and Spring Boot 2.0 updates (45 min) This talk will cover the big ticket items in the 5.0 release of Spring (including Kotlin support, @Nullable and JDK9) and provide an update on Spring Boot 2.0, which is scheduled for the end of the year. Reactive Spring (1h) Spring Framework 5.0 has been released - and it now supports reactive applications in the Spring ecosystem. During this presentation, we'll talk about the reactive foundations of Spring Framework with the Reactor project and the reactive streams specification. We'll al...

Reactive probing of macroscopically quantum mechanical SQUID rings

International Nuclear Information System (INIS)

Prance, R.J.; Clark, T.D.; Whiteman, R.; Diggins, J.; Ralph, J.F.; Prance, H.; Spiller, T.P.; Widom, A.; Srivastava, Y.

1994-01-01

In this paper we demonstrate that the energy level structure of ultra small capacitance SQUID rings can be probed adiabatically at radio frequency using both dynamical and quasistatic reactive techniques. ((orig.))

Reusable Launch Vehicle Attitude Control Using a Time-Varying Sliding Mode Control Technique

Science.gov (United States)

Shtessel, Yuri B.; Zhu, J. Jim; Daniels, Dan; Jackson, Scott (Technical Monitor)

2002-01-01

In this paper we present a time-varying sliding mode control (TVSMC) technique for reusable launch vehicle (RLV) attitude control in ascent and entry flight phases. In ascent flight the guidance commands Euler roll, pitch and yaw angles, and in entry flight it commands the aerodynamic angles of bank, attack and sideslip. The controller employs a body rate inner loop and the attitude outer loop, which are separated in time-scale by the singular perturbation principle. The novelty of the TVSMC is that both the sliding surface and the boundary layer dynamics can be varied in real time using the PD-eigenvalue assignment technique. This salient feature is used to cope with control command saturation and integrator windup in the presence of severe disturbance or control effector failure, which enhances the robustness and fault tolerance of the controller. The TV-SMC ascent and descent designs are currently being tested with high fidelity, 6-DOF dispersion simulations. The test results will be presented in the final version of this paper.

SCRAM reactivity calculations with the KIKO3D code

International Nuclear Information System (INIS)

Hordosy, G.; Kerszturi, A.; Maraczy, Cs.; Temesvari, E.

1999-01-01

Discrepancies between calculated static reactivities and measured reactivities evaluated with reactivity meters led to investigating SCRAM with the KIKO3D dynamic code, The time and space dependent neutron flux in the reactor core during the rod drop measurement was calculated by the KIKO3D nodal diffusion code. For calculating the ionisation chamber signals the Green function technique was applied. The Green functions of ionisation chambers were evaluated via solving the neutron transport equation in the reflector regions with the MCNP Monte Carlo code. The detector signals during asymmetric SCRAM measurements were calculated and compared with measured data using the inverse point kinetics transformation. The sufficient agreement validates the KIKO3D code to determine the reactivities after SCRAM. (Authors)

THE IMPACT OF POWER COEFFICIENT OF REACTIVITY ON CANDU 6 REACTORS

Directory of Open Access Journals (Sweden)

D. KASTANYA

2013-10-01

Full Text Available The combined effects of reactivity coefficients, along with other core nuclear characteristics, determine reactor core behavior in normal operation and accident conditions. The Power Coefficient of Reactivity (PCR is an aggregate indicator representing the change in reactor core reactivity per unit change in reactor power. It is an integral quantity which captures the contributions of the fuel temperature, coolant void, and coolant temperature reactivity feedbacks. All nuclear reactor designs provide a balance between their inherent nuclear characteristics and the engineered reactivity control features, to ensure that changes in reactivity under all operating conditions are maintained within a safe range. The CANDU® reactor design takes advantage of its inherent nuclear characteristics, namely a small magnitude of reactivity coefficients, minimal excess reactivity, and very long prompt neutron lifetime, to mitigate the demand on the engineered systems for controlling reactivity and responding to accidents. In particular, CANDU reactors have always taken advantage of the small value of the PCR associated with their design characteristics, such that the overall design and safety characteristics of the reactor are not sensitive to the value of the PCR. For other reactor design concepts a PCR which is both large and negative is an important aspect in the design of their engineered systems for controlling reactivity. It will be demonstrated that during Loss of Regulation Control (LORC and Large Break Loss of Coolant Accident (LBLOCA events, the impact of variations in power coefficient, including a hypothesized larger than estimated PCR, has no safety-significance for CANDU reactor design. Since the CANDU 6 PCR is small, variations in the range of values for PCR on the performance or safety of the reactor are not significant.

Admission Control Techniques for UMTS System

Directory of Open Access Journals (Sweden)

P. Kejik

2010-09-01

Full Text Available Universal mobile telecommunications system (UMTS is one of the 3rd generation (3G cell phone technologies. The capacity of UMTS is interference limited. Radio resources management (RRM functions are therefore used. They are responsible for supplying optimum coverage, ensuring efficient use of physical resources, and providing the maximum planned capacity. This paper deals with admission control techniques for UMTS. An own UMTS simulation program and several versions of proposed admission control algorithms are presented in this paper. These algorithms are based on fuzzy logic and genetic algorithms. The performance of algorithms is verified via simulations.

Better cognitive control of emotional information is associated with reduced pro-inflammatory cytokine reactivity to emotional stress.

Science.gov (United States)

Shields, Grant S; Kuchenbecker, Shari Young; Pressman, Sarah D; Sumida, Ken D; Slavich, George M

2016-01-01

Stress is strongly associated with several mental and physical health problems that involve inflammation, including asthma, cardiovascular disease, certain types of cancer, and depression. It has been hypothesized that better cognitive control of emotional information may lead to reduced inflammatory reactivity to stress and thus better health, but to date no studies have examined whether differences in cognitive control predict pro-inflammatory cytokine responses to stress. To address this issue, we conducted a laboratory-based experimental study in which we randomly assigned healthy young-adult females to either an acute emotional stress (emotionally evocative video) or no-stress (control video) condition. Salivary levels of the key pro-inflammatory cytokines IL-1β, IL-6, and IL-8 were measured before and after the experimental manipulation, and following the last cytokine sample, we assessed participants' cognitive control of emotional information using an emotional Stroop task. We also assessed participants' cortisol levels before and after the manipulation to verify that documented effects were specific to cytokines and not simply due to increased nonwater salivary output. As hypothesized, the emotional stressor triggered significant increases in IL-1β, IL-6, and IL-8. Moreover, even in fully adjusted models, better cognitive control following the emotional (but not control) video predicted less pronounced cytokine responses to that stressor. In contrast, no effects were observed for cortisol. These data thus indicate that better cognitive control specifically following an emotional stressor is uniquely associated with less pronounced pro-inflammatory cytokine reactivity to such stress. These findings may therefore help explain why superior cognitive control portends better health over the lifespan.

Lithospheric controls on crustal reactivation and intraplate mountain building in the Gobi Corridor, Central Asia

Science.gov (United States)

Cunningham, D.

2017-12-01

This talk will review the Permian-Recent tectonic history of the Gobi Corridor region which includes the actively deforming Gobi Altai-Altai, Eastern Tien Shan, Beishan and North Tibetan foreland. Since terrane amalgamation in the Permian, Gobi Corridor crust has been repeatedly reactivated by Triassic-Jurassic contraction/transpression, Late Cretaceous extension and Late Cenozoic transpression. The tectonic history of the region suggests the following basic principle for intraplate continental regions: non-cratonized continental interior terrane collages are susceptible to repeated intraplate reactivation events, driven by either post-orogenic collapse and/or compressional stresses derived from distant plate boundary convergence. Thus, important related questions are: 1) what lithospheric pre-conditions favor intraplate crustal reactivation in the Gobi Corridor (simple answer: crustal thinning, thermal weakening, strong buttressing cratons), 2) what are the controls on the kinematics of deformation and style of mountain building in the Gobi-Altai-Altai, Beishan and North Tibetan margin (simple answer: many factors, but especially angular relationship between SHmax and `crustal grain'), 3) how does knowledge of the array of Quaternary faults and the historical earthquake record influence our understanding of modern earthquake hazards in continental intraplate regions (answer: extrapolation of derived fault slip rates and recurrence interval determinations are problematic), 4) what important lessons can we learn from the Mesozoic-Cenozoic tectonic history of Central Asia that is applicable to the tectonic evolution of all intraplate continental regions (simple answer: ancient intraplate deformation events may be subtly expressed in the rock record and only revealed by low-temperature thermochronometers, preserved orogen-derived sedimentary sequences, fault zone evidence for younger brittle reactivation, and recognition of a younger class of cross-cutting tectonic

Design and synthesis of reactive separation systems

Energy Technology Data Exchange (ETDEWEB)

Doherty, M.F.

1992-01-01

During the last decade there has been a rapid upturn in interest in reactive distillation. The chemical process industry recognizes the favorable economics of carrying out reaction simultaneously with distillation for certain classes of reacting systems, and many new processes have been built based on this technology. Interest is also increasing by academics and software vendors. Systematic design methods for reactive distillation systems have only recently begun to emerge. In this report we survey the available design techniques and point out the contributions made by our group at the University of Massachusetts.

Inherent reactor power controller for a metal-fueled ALMR

International Nuclear Information System (INIS)

Wood, R.T.; Wilson, T.L. Jr.

1990-01-01

Inherent power control for metal-fueled ALMR designs involves using reactivity thermal feedback effects to control reactor power. This paper describes how, using classical control design techniques, a control system for normal load following maneuvers was deigned for a pool-type ALMR. This design provides active control of power removal in the balance of plant, direct control of selected primary and intermediate loop temperatures, and passive control of reactor power. The inherent stability of the strong, fast reactivity feedback effects bring heat production in the core into balance with the heat removal system temperatures, which are controlled to meet power demand. A simulation of the control system successfully responded to a 10% step change in power demand by changing power at an acceptable rate without causing large temperature fluctuations or exceeding thermal limits

Prevention and control of zebra mussels: proactive and reactive strategies

International Nuclear Information System (INIS)

Claudi, R.

1998-01-01

Most plant people would agree that having zebra mussels in any raw water system is not desirable. System blockage, loss of heat transfer and other associated safety hazards are not pleasant to deal with. Therefore most industries strive to minimise the effect of infestation. Opinions differ as to how to do this most efficiently and economically. Some facilities are committed to preventing the settlement of veligers in their piping systems and on some of the external structures they consider critical. This is the proactive approach. Others allow settlement and only treat the system or surface after fouling has occurred. This is the reactive approach. Which is the best and most economical treatment will depend on the individual facility and sometimes on the individual system. The paper examines the different proactive and reactive strategies available to-date and how they are being used. It will also discuss some of the criteria for choosing a proactive vs. reactive approach and why the decision has to be made individually by each facility. (author)

Prevention and control of zebra mussels: proactive and reactive strategies

Energy Technology Data Exchange (ETDEWEB)

Claudi, R. [Ontario Hydro Nuclear, Toronto, ON (Canada)

1998-07-01

Most plant people would agree that having zebra mussels in any raw water system is not desirable. System blockage, loss of heat transfer and other associated safety hazards are not pleasant to deal with. Therefore most industries strive to minimise the effect of infestation. Opinions differ as to how to do this most efficiently and economically. Some facilities are committed to preventing the settlement of veligers in their piping systems and on some of the externalstructures they consider critical. This is the proactive approach. Others allow settlement and only treat the system or surface after fouling has occurred. This is the reactive approach. Which is the best and most economical treatment will depend on the individual facility and sometimes on the individual system. The paper examines the different proactive and reactive strategies available to-date and how they are being used. It will also discuss some of the criteria for choosing a proactive vs. reactive approach and why the decision has to be made individually by each facility. (author)

Improvement of the dynamic response of the ITER Reactive Power Compensation system

International Nuclear Information System (INIS)

Finotti, Claudio; Gaio, Elena; Song, Inho; Tao, Jun; Benfatto, Ivone

2015-01-01

Highlights: • The slow response reasons of the classic ITER Reactive Power Compensation (RPC) control are explained. • The dynamic behaviors of the ac/dc converter and of the RPC are characterized. • New control concept to speed up the RPC response is developed. • Good performance of the new RPC control is verified even during fast transient conditions. - Abstract: The ITER ac/dc conversion system can absorb a total active and reactive power up to 500 MW and 950 Mvar, respectively. The Reactive Power Compensation (RPC) system is rated for a nominal power of 750 Mvar necessary to comply with the allowable reactive power limit value from the grid of 200 Mvar. This system is currently under construction and is based on Static Var Compensation technology with Thyristor Controlled Reactor (TCR) and Tuned Filters. The RPC has to minimize the demand of reactive power from the grid; its control is based on a feed-forward method, where the corrective input is the measurement of the reactive power consumption of the ac/dc converters, derived from the 50 Hz component of the Fast Fourier Transform (FFT) of the three-phase voltages and currents. The delay introduced by the FFT calculation and the slow response of the TCR could make the response speed of the RPC not sufficient to face fast variations of the reactive power demand and therefore in this paper a new controller of the RPC able to overcome this shortcoming is proposed and evaluated. It is based on the calculation of the predicted consumption of the reactive power by using the voltage reference signals coming from the Plasma Control System and the measurements of the dc current of the ac/dc converters and of the 66 kV busbar voltage, and on the speed up of the RPC control by introducing a lead–lag transfer function.

Improvement of the dynamic response of the ITER Reactive Power Compensation system

Energy Technology Data Exchange (ETDEWEB)

Finotti, Claudio, E-mail: claudio.finotti@igi.cnr.it [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Gaio, Elena [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Song, Inho; Tao, Jun; Benfatto, Ivone [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France)

2015-10-15

Highlights: • The slow response reasons of the classic ITER Reactive Power Compensation (RPC) control are explained. • The dynamic behaviors of the ac/dc converter and of the RPC are characterized. • New control concept to speed up the RPC response is developed. • Good performance of the new RPC control is verified even during fast transient conditions. - Abstract: The ITER ac/dc conversion system can absorb a total active and reactive power up to 500 MW and 950 Mvar, respectively. The Reactive Power Compensation (RPC) system is rated for a nominal power of 750 Mvar necessary to comply with the allowable reactive power limit value from the grid of 200 Mvar. This system is currently under construction and is based on Static Var Compensation technology with Thyristor Controlled Reactor (TCR) and Tuned Filters. The RPC has to minimize the demand of reactive power from the grid; its control is based on a feed-forward method, where the corrective input is the measurement of the reactive power consumption of the ac/dc converters, derived from the 50 Hz component of the Fast Fourier Transform (FFT) of the three-phase voltages and currents. The delay introduced by the FFT calculation and the slow response of the TCR could make the response speed of the RPC not sufficient to face fast variations of the reactive power demand and therefore in this paper a new controller of the RPC able to overcome this shortcoming is proposed and evaluated. It is based on the calculation of the predicted consumption of the reactive power by using the voltage reference signals coming from the Plasma Control System and the measurements of the dc current of the ac/dc converters and of the 66 kV busbar voltage, and on the speed up of the RPC control by introducing a lead–lag transfer function.

Appetitive motivation and negative emotion reactivity among remitted depressed youth.

Science.gov (United States)

Hankin, Benjamin L; Wetter, Emily K; Flory, Kate

2012-01-01

Depression has been characterized as involving altered appetitive motivation and emotional reactivity. Yet no study has examined objective indices of emotional reactivity when the appetitive/approach system is suppressed in response to failure to attain a self-relevant goal and desired reward. Three groups of youth (N = 98, ages 9-15; remitted depressed, n = 34; externalizing disordered without depression, n = 30; and healthy controls, n = 34) participated in a novel reward striving task designed to activate the appetitive/approach motivation system. Objective facial expressions of emotion were videotaped and coded throughout both failure (i.e., nonreward) and control (success and reward) conditions. Observational coding of facial expressions as well as youths' subjective emotion reports showed that the remitted depressed youth specifically exhibited more negative emotional reactivity to failure in the reward striving task, but not the control condition. Neither externalizing disordered (i.e., attention deficit hyperactivity disorder, conduct disorder, and/or oppositional defiant disorder) nor control youth displayed greater negative emotional reactivity in either the failure or control condition. Findings suggest that depression among youth is related to dysregulated appetitive motivation and associated negative emotional reactivity after failing to achieve an important, self-relevant goal and not attaining reward. These deficits in reward processing appear to be specific to depression as externalizing disordered youth did not display negative emotional reactivity to failure after their appetitive motivation system was activated.

Fuel Temperature Coefficient of Reactivity

Energy Technology Data Exchange (ETDEWEB)

Loewe, W.E.

2001-07-31

A method for measuring the fuel temperature coefficient of reactivity in a heterogeneous nuclear reactor is presented. The method, which is used during normal operation, requires that calibrated control rods be oscillated in a special way at a high reactor power level. The value of the fuel temperature coefficient of reactivity is found from the measured flux responses to these oscillations. Application of the method in a Savannah River reactor charged with natural uranium is discussed.

Active and reactive power neurocontroller for grid-connected photovoltaic generation system

Directory of Open Access Journals (Sweden)

I. Abadlia

2016-03-01

Full Text Available Many researchers have contributed to the development of a firm foundation for analysis and design of control applications in grid-connected renewable energy sources. This paper presents an intelligent control algorithm fond on artificial neural networks for active and reactive power controller in grid-connected photovoltaic generation system. The system is devices into two parts in which each part contains an inverter with control algorithm. A DC/DC converter in output voltage established by control magnitude besides maximum power point tracker algorithm always finds optimal power of the PV array in use. A DC/AC hysteresis inverter designed can synchronize a sinusoidal current output with the grid voltage and accurate an independent active and reactive power control. Simulation results confirm the validation of the purpose. Neurocontroller based active and reactive power presents an efficiency control that guarantees good response to the steps changing in active and reactive power with an acceptable current/voltage synchronism. In this paper the power circuit and the control system of the presented grid-connected photovoltaic generation system is simulated and tested by MatLab/Simulink.

Predicting fissile content of spent nuclear fuel assemblies with the Passive Neutron Albedo Reactivity technique and Monte Carlo code emulation

International Nuclear Information System (INIS)

Conlin, Jeremy Lloyd; Tobin, Stephen J.

2011-01-01

There is a great need in the safeguards community to be able to nondestructively quantify the mass of plutonium of a spent nuclear fuel assembly. As part of the Next Generation of Safeguards Initiative, we are investigating several techniques, or detector systems, which, when integrated, will be capable of quantifying the plutonium mass of a spent fuel assembly without dismantling the assembly. This paper reports on the simulation of one of these techniques, the Passive Neutron Albedo Reactivity with Fission Chambers (PNAR-FC) system. The response of this system over a wide range of spent fuel assemblies with different burnup, initial enrichment, and cooling time characteristics is shown. A Monte Carlo method of using these modeled results to estimate the fissile content of a spent fuel assembly has been developed. A few numerical simulations of using this method are shown. Finally, additional developments still needed and being worked on are discussed. (author)

Investigation of Reactive Power Control Effects on Flicker and Harmonics Emission of a DFIG Wind Turbine

Directory of Open Access Journals (Sweden)

Amir Nagizadeh Ghoogdareh

2013-01-01

Full Text Available One of the most important power quality aspects in wind farms is voltage fluctuation or flicker which should be investigated due to the nature of wind speed variations. These variations result in power and voltage fluctuations at the load bus. Moreover, the wind generation systems may be assumed as a harmonics source because of their power electronic converters. There are numerous factors that affect flicker and harmonic emission of grid-connected wind turbines during continuous operation, such as wind characteristics (e.g. mean wind speed, turbulence intensity, type of generator and grid conditions (e.g. short circuit capacity, grid impedance angle. In this paper, an IEC based flickermeter is first modeled and then a variable speed wind turbine has been simulated by Matlab/Simulink software. The flicker and harmonics emissions of wind turbines equipped with DFIG during continuous operation and using output reactive control are investigated. The simulation results show that control of wind turbine output reactive power is an effective means for flicker mitigation during continuous operation. However, there should be a compromise between flicker reduction and harmonics level increase to enhance the whole power quality of wind turbine.

Controllable generation of reactive oxygen species by femtosecond-laser irradiation

Science.gov (United States)

Yan, Wei; He, Hao; Wang, Yintao; Wang, Yisen; Hu, Minglie; Wang, Chingyue

2014-02-01

Femtosecond lasers have been advancing Biophotonics research in the past two decades with multiphoton microscopy, microsurgery, and photodynamic therapy. Nevertheless, laser irradiation is identified to bring photodamage to cells via reactive oxygen species (ROS) generation with unclear mechanism. Meanwhile, currently in biological researches, there is no effective method to provide controllable ROS production precisely, which originally is leaked from mitochondria during respiration and plays a key role in a lot of important cellular processes and cellular signaling pathways. In this study, we show the process of how the tightly focused femtosecond-laser induces ROS generation solely in mitochondria at the very beginning and then release to cytosol if the stimulus is intense enough. At certain weak power levels, the laser pulses induce merely moderate Ca2+ release but this is necessary for the laser to generate ROS in mitochondria. Cellular original ROS are also involved with a small contribution. When the power is above a threshold, ROS are then released to cytosol, indicating photodamage overwhelming cellular repair ability. The mechanisms in those two cases are quite different. Those results clarify parts of the mechanism in laser-induced ROS generation. Hence, it is possible to further this optical scheme to provide controllable ROS generation for ROS-related biological researches including mitochondrial diseases and aging.

Controllable generation of reactive oxygen species by femtosecond-laser irradiation

Energy Technology Data Exchange (ETDEWEB)

Yan, Wei; He, Hao, E-mail: haohe@tju.edu.cn; Wang, Yintao; Wang, Yisen; Hu, Minglie; Wang, Chingyue [Ultrafast Laser Laboratory, Key Laboratory of Optoelectronic Information Technology (Ministry of Education), College of Precision Instrument and Optoelectronics Engineering, Tianjin University, Tianjin (China)

2014-02-24

Femtosecond lasers have been advancing Biophotonics research in the past two decades with multiphoton microscopy, microsurgery, and photodynamic therapy. Nevertheless, laser irradiation is identified to bring photodamage to cells via reactive oxygen species (ROS) generation with unclear mechanism. Meanwhile, currently in biological researches, there is no effective method to provide controllable ROS production precisely, which originally is leaked from mitochondria during respiration and plays a key role in a lot of important cellular processes and cellular signaling pathways. In this study, we show the process of how the tightly focused femtosecond-laser induces ROS generation solely in mitochondria at the very beginning and then release to cytosol if the stimulus is intense enough. At certain weak power levels, the laser pulses induce merely moderate Ca{sup 2+} release but this is necessary for the laser to generate ROS in mitochondria. Cellular original ROS are also involved with a small contribution. When the power is above a threshold, ROS are then released to cytosol, indicating photodamage overwhelming cellular repair ability. The mechanisms in those two cases are quite different. Those results clarify parts of the mechanism in laser-induced ROS generation. Hence, it is possible to further this optical scheme to provide controllable ROS generation for ROS-related biological researches including mitochondrial diseases and aging.

Controllable generation of reactive oxygen species by femtosecond-laser irradiation

International Nuclear Information System (INIS)

Yan, Wei; He, Hao; Wang, Yintao; Wang, Yisen; Hu, Minglie; Wang, Chingyue

2014-01-01

Femtosecond lasers have been advancing Biophotonics research in the past two decades with multiphoton microscopy, microsurgery, and photodynamic therapy. Nevertheless, laser irradiation is identified to bring photodamage to cells via reactive oxygen species (ROS) generation with unclear mechanism. Meanwhile, currently in biological researches, there is no effective method to provide controllable ROS production precisely, which originally is leaked from mitochondria during respiration and plays a key role in a lot of important cellular processes and cellular signaling pathways. In this study, we show the process of how the tightly focused femtosecond-laser induces ROS generation solely in mitochondria at the very beginning and then release to cytosol if the stimulus is intense enough. At certain weak power levels, the laser pulses induce merely moderate Ca 2+ release but this is necessary for the laser to generate ROS in mitochondria. Cellular original ROS are also involved with a small contribution. When the power is above a threshold, ROS are then released to cytosol, indicating photodamage overwhelming cellular repair ability. The mechanisms in those two cases are quite different. Those results clarify parts of the mechanism in laser-induced ROS generation. Hence, it is possible to further this optical scheme to provide controllable ROS generation for ROS-related biological researches including mitochondrial diseases and aging

Control System Design for Cylindrical Tank Process Using Neural Model Predictive Control Technique

Directory of Open Access Journals (Sweden)

M. Sridevi

2010-10-01

Full Text Available Chemical manufacturing and process industry requires innovative technologies for process identification. This paper deals with model identification and control of cylindrical process. Model identification of the process was done using ARMAX technique. A neural model predictive controller was designed for the identified model. The performance of the controllers was evaluated using MATLAB software. The performance of NMPC controller was compared with Smith Predictor controller and IMC controller based on rise time, settling time, overshoot and ISE and it was found that the NMPC controller is better suited for this process.

Modern insect control: Nuclear techniques and biotechnology

International Nuclear Information System (INIS)

1988-01-01

The Symposium dealt primarily with genetic methods of insect control, including sterile insect technique (SIT), F 1 sterility, compound chromosomes, translocations and conditional lethals. Research and development activities on various aspects of these control technologies were reported by participants during the Symposium. Of particular interest was development of F 1 sterility as a practical method of controlling pest Lepidoptera. Genetic methods of insect control are applicable only on an area wide basis. They are species specific and thus do not reduce populations of beneficial insects or cause other environmental problems. Other papers presented reported on the potential use of radiation as a quarantine treatment for commodities in international trade and the use of radioisotopes as ''tags'' in studying insects

Measurement of xenon reactivity in the reactor of the nuclear ship 'MUTSU'

International Nuclear Information System (INIS)

Itagaki, Masafumi; Miyoshi, Yoshinori; Gakuhari, Kazuhiko; Okada, Noboru.

1993-01-01

This report deals with the measurement of reactivity changes caused by the increase and decrease of xenon concentration in the reactor core of the nuclear ship 'MUTSU' after a change from long-term operation at 70 % to zero power. The change in xenon reactivity was compensated by control-rod movements and the compensated reactivity was measured using a digital reactivity meter. The xenon override peak was recognized five and half hours after the start of power reduction. The equilibrium and peak reactivities of xenon were estimated by reading the initial and peak values of a theoretical curve which was fitted to the measured variation in xenon reactivity. The xenon reactivity results obtained by the present method can be considered to be accurate since no control-rod worth data were used and the measured quantity was the reactivity itself. (author)

Fabrication of Polymeric Coatings with Controlled Microtopographies Using an Electrospraying Technique.

Directory of Open Access Journals (Sweden)

Qiongyu Guo

Full Text Available Surface topography of medical implants provides an important biophysical cue on guiding cellular functions at the cell-implant interface. However, few techniques are available to produce polymeric coatings with controlled microtopographies onto surgical implants, especially onto implant devices of small dimension and with complex structures such as drug-eluting stents. Therefore, the main objective of this study was to develop a new strategy to fabricate polymeric coatings using an electrospraying technique based on the uniqueness of this technique in that it can be used to produce a mist of charged droplets with a precise control of their shape and dimension. We hypothesized that this technique would allow facile manipulation of coating morphology by controlling the shape and dimension of electrosprayed droplets. More specifically, we employed the electrospraying technique to coat a layer of biodegradable polyurethane with tailored microtopographies onto commercial coronary stents. The topography of such stent coatings was modulated by controlling the ratio of round to stretched droplets or the ratio of round to crumped droplets under high electric field before deposition. The shape of electrosprayed droplets was governed by the stability of these charged droplets right after ejection or during their flight in the air. Using the electrospraying technique, we achieved conformal polymeric coatings with tailored microtopographies onto conductive surgical implants. The approach offers potential for controlling the surface topography of surgical implant devices to modulate their integration with surrounding tissues.

Application of PQR Theory for control of a 3-phase 4-wire 4-legs shunt active power filter in the aß?-axes using 3D-SVM technique

Directory of Open Access Journals (Sweden)

Ali CHEBABHI

2015-05-01

Full Text Available This article discusses and compares two control strategies applied to a 3-phase 4-wire 4-leg shunt active power filter. These two control strategies, including the cross-vector theory called CV theory and the direct method called PQR theory, are based on the instantaneous control of active and reactive power. On one hand, it is shown that, in some cases, cross-vector theory requires elimination of the zero sequence currents in a 3-phase 4-wire 4-leg shunt active power filter, which needs a power storage element, and on the other hand pretreatment system voltage is necessary to obtain compensated sinusoidal current and a degree of freedom. By relying on the cross-vector theory, the PQR theory is used to extract and remove harmonic currents components. In this control technique, there are two internal current control loops and an external voltage control loop, these control loops have been realized by PI controllers when applied 3D-SVM of switching technique. We choose as criteria for comparison the transient and the Total Harmonic Distortion in the line current. A series of simulations in MATLAB/ Simulink environment have been presented and discussed to show the performance of the two control strategies.

Losing memories during sleep after targeted memory reactivation.

Science.gov (United States)

Simon, Katharine C N S; Gómez, Rebecca L; Nadel, Lynn

2018-03-17

Targeting memories during sleep opens powerful and innovative ways to influence the mind. We used targeted memory reactivation (TMR), which to date has been shown to strengthen learned episodes, to instead induce forgetting (TMR-Forget). Participants were first trained to associate the act of forgetting with an auditory forget tone. In a second, separate, task they learned object-sound-location pairings. Shortly thereafter, some of the object sounds were played during slow wave sleep, paired with the forget tone to induce forgetting. One week later, participants demonstrated lower recall of reactivated versus non-reactivated objects and impaired recognition memory and lowered confidence for the spatial location of the reactivated objects they failed to spontaneously recall. The ability to target specific episodic memories for forgetting during sleep has implications for developing novel therapeutic techniques for psychological disorders such as PTSD and phobias. Copyright © 2018 Elsevier Inc. All rights reserved.

A micro-chip initiator with controlled combustion reactivity realized by integrating Al/CuO nanothermite composites on a microhotplate platform

International Nuclear Information System (INIS)

Ahn, Ji Young; Lee, Hyung Woo; Kim, Jong Man; Kim, Soo Hyung; Kim, Sang Beom; Kim, Ji Hoon; Jang, Nam Su; Kim, Dae Hyun

2016-01-01

The interfacial contact area between the fuel and oxidizer components plays an important role in determining the combustion reactivity of nanothermite composites. In addition, the development of compact and reliable ignition methods can extend the applicability of nanothermite composites to various thermal engineering fields. In this study we report the development of a micro-chip initiator with controlled combustion reactivity using concepts usually applied to microelectromechanical systems (MEMS) and simple nanofabrication processes. The nanothermite composites fabricated in this study consisted of aluminum nanoparticles (Al NPs) as the fuel and copper oxide nanoparticles (CuO NPs) as the oxidizer accumulated on a silicon oxide substrate with a serpentine-shaped gold (Au) electrode. The micro-chip initiator rapidly ignited and exploded when minimal current was supplied. The effects of stacking structures of Al and CuO-based multilayers on the combustion properties were systematically investigated in terms of the pressurization rate, peak explosion time, and heat flow. Pressurization rates of 0.004–0.025 MPa μs −1 and heat flows of 2.0–3.8 kJ g −1 with a commonly fast response time of less than 20 ms could be achieved by simply changing the interfacial structures of the Al and CuO multilayers. The controllability of combustion reactivity of micro-chip initiator can be made for general nanothermite composites composed of Al and various metal oxides (e.g. Fe 2 O 3 , CuO, KMnO 4 , etc). The micro-chip initiator fabricated in this study was reliable, compact, and proved to be a versatile platform, exhibiting controlled combustion reactivity and fast response time, which could be used for various civilian and military thermal engineering applications, such as in initiators and propulsion, welding, and ordinance systems. (paper)

Fail-safe reactivity compensation method for a nuclear reactor

Science.gov (United States)

Nygaard, Erik T.; Angelo, Peter L.; Aase, Scott B.

2018-01-23

The present invention relates generally to the field of compensation methods for nuclear reactors and, in particular to a method for fail-safe reactivity compensation in solution-type nuclear reactors. In one embodiment, the fail-safe reactivity compensation method of the present invention augments other control methods for a nuclear reactor. In still another embodiment, the fail-safe reactivity compensation method of the present invention permits one to control a nuclear reaction in a nuclear reactor through a method that does not rely on moving components into or out of a reactor core, nor does the method of the present invention rely on the constant repositioning of control rods within a nuclear reactor in order to maintain a critical state.

Analysis technique for controlling system wavefront error with active/adaptive optics

Science.gov (United States)

Genberg, Victor L.; Michels, Gregory J.

2017-08-01

The ultimate goal of an active mirror system is to control system level wavefront error (WFE). In the past, the use of this technique was limited by the difficulty of obtaining a linear optics model. In this paper, an automated method for controlling system level WFE using a linear optics model is presented. An error estimate is included in the analysis output for both surface error disturbance fitting and actuator influence function fitting. To control adaptive optics, the technique has been extended to write system WFE in state space matrix form. The technique is demonstrated by example with SigFit, a commercially available tool integrating mechanical analysis with optical analysis.

Stress reactivity and emotion in premenstrual syndrome

Directory of Open Access Journals (Sweden)

Liu Q

2017-06-01

Full Text Available Qing Liu,1 Yongshun Wang,2 Cornelis Hermanus van Heck,3 Wei Qiao4 1Department of Nuclear Medicine and Medical PET Center, The Second Hospital of Zhejiang University School of Medicine, Zhejiang University, Hangzhou, 2School of Physical Education and Sport, Huaqiao University, Xiamen, People’s Republic of China; 3DCC, Donders Institute for Neuroscience and Neurocognition, Arnhem, the Netherlands; 4Department of Physical Education, Xiamen Institute of Technology, Xiamen, People’s Republic of China Background: Hormone level fluctuation across the menstrual cycle causes women to experience negative emotions and also affects their mood regulation and stress sensitivity. However, the stress reactivity and emotional variations in women with premenstrual syndrome (PMS, who are especially sensitive to the variations in hormone cycles, have not been explained. Methods: The present study used an electroencephalogram (EEG stress evaluation test, a physiology stress evaluation test, and the positive affect and negative affect scale (PANAS to evaluate the stress reactivity pattern and emotional state of women with PMS. Results: The results showed that women with PMS had higher negative affect and lower positive affect compared with controls. Moreover, under stressful conditions, the women with PMS had a higher alpha activity and a lower respiration rate than the controls. The differences in stress reactivity and emotional states between women with PMS and controls were based on a covariant analysis with menstrual cycle (luteal and follicular phases as the covariate. Conclusion: The results demonstrated that, compared with controls, women suffering from PMS have a continuous abnormality in emotional state and stress reactivity, which was independent of the menstrual cycle. Keywords: premenstrual syndrome, stress reactivity, emotion, EEG stress evaluation test, physiology stress evaluation test

Investigation of Ternary Transition-Metal Nitride Systems by Reactive Cosputtering

NARCIS (Netherlands)

Dover, R.B. Van; Hessen, B.; Werder, D.; Chen, C.-H.; Felder, R.J.

1993-01-01

A reactive dc cosputtering technique has been used to evaluate compound formation in bimetallic transition-metal nitride systems. A wide range in M-M’ composition can be studied in a single deposition run, and the method is applicable to nonalloying metal combinations. Using this technique, it was

Heated hatha yoga to target cortisol reactivity to stress and affective eating in women at risk for obesity-related illnesses: A randomized controlled trial.

Science.gov (United States)

Hopkins, Lindsey B; Medina, Johnna L; Baird, Scarlett O; Rosenfield, David; Powers, Mark B; Smits, Jasper A J

2016-06-01

Cortisol reactivity to stress is associated with affective eating, an important behavioral risk factor for obesity and related metabolic diseases. Yoga practice is related to decreases in stress and cortisol levels, thus emerging as a potential targeted complementary intervention for affective eating. This randomized controlled trial examined the efficacy of a heated, hatha yoga intervention for reducing cortisol reactivity to stress and affective eating. Females (N = 52; ages 25-46 years; 75% White) at risk for obesity and related illnesses were randomly assigned to 8 weeks of Bikram Yoga practice or to waitlist control. Cortisol reactivity to a laboratory stress induction were measured at Weeks 0 (pretreatment) and 9 (posttreatment). Self-reported binge eating frequency and coping motives for eating were assessed at Weeks 0, 3, 6, and 9. Among participants with elevated cortisol reactivity at pretreatment ("high reactors"), those randomized to the yoga condition evidenced greater pre- to posttreatment reductions in cortisol reactivity (p = .042, d = .85), but there were not significant condition differences for the "low reactors" (p = .178, d = .53). Yoga participants reported greater decreases in binge eating frequency (p = .040, d = .62) and eating to cope with negative affect (p = .038, d = .54). This study provides preliminary support for the efficacy of heated hatha yoga for treating physiological stress reactivity and affective eating among women at risk for obesity-related illnesses. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Polymer degradation in reactive ion etching and its possible application to all dry processes

International Nuclear Information System (INIS)

Hiraoka, H.; Welsh, L.W. Jr.

1981-01-01

Dry etching processes involving CF 4 -plasma and reactive ion etching become increasingly important for microcircuit fabrication techniques. In these techniques polymer degradation and etch resistance against reactive species like F atoms and CF 3 + ions are the key factors in the processes. It is well-known that classical electron beam resists like poly(methyl methacrylate) and poly(1-butene sulfone) are not suitable for dry etching processes because they degrade rapidly under these etching conditions. In order to find a correlation of etching rate and polymer structures the thickness loss of polymer films have been measured for a variety of polymer films in reactive ion etching conditions, where CF 3 + ions are the major reactive species with an accelerating potential of 500 volts. Because of its high CF 4 -plasma and reactive ion etch resistance, and because of its high electron beam sensitivity, poly(methacrylonitrile) provides a positive working electron beam resist uniquely suited for all dry processes. (author)

The reactivity meter and core reactivity

International Nuclear Information System (INIS)

Siltanen, P.

1999-01-01

This paper discussed in depth the point kinetic equations and the characteristics of the point kinetic reactivity meter, particularly for large negative reactivities. From a given input signal representing the neutron flux seen by a detector, the meter computes a value of reactivity in dollars (ρ/β), based on inverse point kinetics. The prompt jump point of view is emphasised. (Author)

Effect of novel inhaler technique reminder labels on the retention of inhaler technique skills in asthma: a single-blind randomized controlled trial.

Science.gov (United States)

Basheti, Iman A; Obeidat, Nathir M; Reddel, Helen K

2017-02-09

Inhaler technique can be corrected with training, but skills drop off quickly without repeated training. The aim of our study was to explore the effect of novel inhaler technique labels on the retention of correct inhaler technique. In this single-blind randomized parallel-group active-controlled study, clinical pharmacists enrolled asthma patients using controller medication by Accuhaler [Diskus] or Turbuhaler. Inhaler technique was assessed using published checklists (score 0-9). Symptom control was assessed by asthma control test. Patients were randomized into active (ACCa; THa) and control (ACCc; THc) groups. All patients received a "Show-and-Tell" inhaler technique counseling service. Active patients also received inhaler labels highlighting their initial errors. Baseline data were available for 95 patients, 68% females, mean age 44.9 (SD 15.2) years. Mean inhaler scores were ACCa:5.3 ± 1.0; THa:4.7 ± 0.9, ACCc:5.5 ± 1.1; THc:4.2 ± 1.0. Asthma was poorly controlled (mean ACT scores ACCa:13.9 ± 4.3; THa:12.1 ± 3.9; ACCc:12.7 ± 3.3; THc:14.3 ± 3.7). After training, all patients had correct technique (score 9/9). After 3 months, there was significantly less decline in inhaler technique scores for active than control groups (mean difference: Accuhaler -1.04 (95% confidence interval -1.92, -0.16, P = 0.022); Turbuhaler -1.61 (-2.63, -0.59, P = 0.003). Symptom control improved significantly, with no significant difference between active and control patients, but active patients used less reliever medication (active 2.19 (SD 1.78) vs. control 3.42 (1.83) puffs/day, P = 0.002). After inhaler training, novel inhaler technique labels improve retention of correct inhaler technique skills with dry powder inhalers. Inhaler technique labels represent a simple, scalable intervention that has the potential to extend the benefit of inhaler training on asthma outcomes. REMINDER LABELS IMPROVE INHALER TECHNIQUE: Personalized

Multidisciplinary Techniques and Novel Aircraft Control Systems

Science.gov (United States)

Padula, Sharon L.; Rogers, James L.; Raney, David L.

2000-01-01

The Aircraft Morphing Program at NASA Langley Research Center explores opportunities to improve airframe designs with smart technologies. Two elements of this basic research program are multidisciplinary design optimization (MDO) and advanced flow control. This paper describes examples where MDO techniques such as sensitivity analysis, automatic differentiation, and genetic algorithms contribute to the design of novel control systems. In the test case, the design and use of distributed shape-change devices to provide low-rate maneuvering capability for a tailless aircraft is considered. The ability of MDO to add value to control system development is illustrated using results from several years of research funded by the Aircraft Morphing Program.

Optimal Control of Wind Farms for Coordinated TSO-DSO Reactive Power Management

Directory of Open Access Journals (Sweden)

David Sebastian Stock

2018-01-01

Full Text Available The growing importance of renewable generation connected to distribution grids requires an increased coordination between transmission system operators (TSOs and distribution system operators (DSOs for reactive power management. This work proposes a practical and effective interaction method based on sequential optimizations to evaluate the reactive flexibility potential of distribution networks and to dispatch them along with traditional synchronous generators, keeping to a minimum the information exchange. A modular optimal power flow (OPF tool featuring multi-objective optimization is developed for this purpose. The proposed method is evaluated for a model of a real German 110 kV grid with 1.6 GW of installed wind power capacity and a reduced order model of the surrounding transmission system. Simulations show the benefit of involving wind farms in reactive power support reducing losses both at distribution and transmission level. Different types of setpoints are investigated, showing the feasibility for the DSO to fulfill also individual voltage and reactive power targets over multiple connection points. Finally, some suggestions are presented to achieve a fair coordination, combining both TSO and DSO requirements.

Methods for the reactivity evaluation in subcritical systems analysis: a review

International Nuclear Information System (INIS)

Dulla, S.; Picca, P.; Carta, M.

2011-01-01

The assessment of the subcritical source-driven system technology for waste incineration and power production requires the development of reliable and efficient techniques for the reactivity evaluation and monitoring. Starting from the standard methods developed for close-to-criticality systems, extensive research activities have been carried out to analyze the behavior of subcritical assembly in time-dependent condition and to infer the subcriticality level from local flux values. In the present work, a review of some key aspects in the method development for ADS analysis is proposed, with special attention to the techniques for reactivity evaluation. (author)

INDIAN POINT REACTOR REACTIVITY AND FLUX DISTRIBUTION MEASUREMENTS

Energy Technology Data Exchange (ETDEWEB)

Batch, M. L.; Fischer, F. E.

1963-11-15

The reactivity of the Indian Point core was measured near zero reactivity at various shim and control rod patterns. Flux distribution measurements were also made, and the results are expressed in terms of power peaking factors and normalized detector response during rod withdrawal. (D.L.C.)

Beam Techniques - Beam Control and Manipulation

International Nuclear Information System (INIS)

Minty, Michiko G

2003-01-01

We describe commonly used strategies for the control of charged particle beams and the manipulation of their properties. Emphasis is placed on relativistic beams in linear accelerators and storage rings. After a brief review of linear optics, we discuss basic and advanced beam control techniques, such as transverse and longitudinal lattice diagnostics, matching, orbit correction and steering, beam-based alignment, and linac emittance preservation. A variety of methods for the manipulation of particle beam properties are also presented, for instance, bunch length and energy compression, bunch rotation, changes to the damping partition number, and beam collimation. The different procedures are illustrated by examples from various accelerators. Special topics include injection and extraction methods, beam cooling, spin transport and polarization

Beam Techniques - Beam Control and Manipulation

Energy Technology Data Exchange (ETDEWEB)

Minty, Michiko G

2003-04-24

We describe commonly used strategies for the control of charged particle beams and the manipulation of their properties. Emphasis is placed on relativistic beams in linear accelerators and storage rings. After a brief review of linear optics, we discuss basic and advanced beam control techniques, such as transverse and longitudinal lattice diagnostics, matching, orbit correction and steering, beam-based alignment, and linac emittance preservation. A variety of methods for the manipulation of particle beam properties are also presented, for instance, bunch length and energy compression, bunch rotation, changes to the damping partition number, and beam collimation. The different procedures are illustrated by examples from various accelerators. Special topics include injection and extraction methods, beam cooling, spin transport and polarization.

Acute effects of muscle fatigue on anticipatory and reactive postural control in older individuals: a systematic review of the evidence.

Science.gov (United States)

Papa, Evan V; Garg, Hina; Dibble, Leland E

2015-01-01

Falls are the leading cause of traumatic brain injury and fractures and the No. 1 cause of emergency department visits by older adults. Although declines in muscle strength and sensory function contribute to increased falls in older adults, skeletal muscle fatigue is often overlooked as an additional contributor to fall risk. In an effort to increase awareness of the detrimental effects of skeletal muscle fatigue on postural control, we sought to systematically review research studies examining this issue. The specific purpose of this review was to provide a detailed assessment of how anticipatory and reactive postural control tasks are influenced by acute muscle fatigue in healthy older individuals. An extensive search was performed using the CINAHL, Scopus, PubMed, SPORTDiscus, and AgeLine databases for the period from inception of each database to June 2013. This systematic review used standardized search criteria and quality assessments via the American Academy for Cerebral Palsy and Developmental Medicine Methodology to Develop Systematic Reviews of Treatment Interventions (2008 version, revision 1.2, AACPDM, Milwaukee, Wisconsin). A total of 334 citations were found. Six studies were selected for inclusion, whereas 328 studies were excluded from the analytical review. The majority of articles (5 of 6) utilized reactive postural control paradigms. All studies incorporated extrinsic measures of muscle fatigue, such as declines in maximal voluntary contraction or available active range of motion. The most common biomechanical postural control task outcomes were spatial measures, temporal measures, and end-points of lower extremity joint kinetics. On the basis of systematic review of relevant literature, it appears that muscle fatigue induces clear deteriorations in reactive postural control. A paucity of high-quality studies examining anticipatory postural control supports the need for further research in this area. These results should serve to heighten

Internally-directed cognition and mindfulness:An integrative perspective derived from reactive versus predictive control systems theory

Directory of Open Access Journals (Sweden)

Mattie eTops

2014-05-01

Full Text Available In the present paper we will apply the Predictive And Reactive Control Systems (PARCS theory as a framework that integrates competing theories of neural substrates of awareness by describing the default mode network (DMN and anterior insula (AI as parts of two different behavioral and homeostatic control systems. The DMN, a network that becomes active at rest when there is no external stimulation or task to perform, has been implicated in self-reflective awareness and prospection. By contrast, the AI is associated with awareness and task-related attention. This has led to competing theories stressing the role of the DMN in self-awareness versus the role of interoceptive and emotional information integration in the AI in awareness of the emotional moment. In PARCS, the respective functions of the DMN and AI in a specific control system explains their association with different qualities of awareness, and how mental states can shift from one state (e.g., prospective self-reflection to the other (e.g., awareness of the emotional moment depending on the relative dominance of control systems. These shifts between reactive and predictive control are part of processes that enable the intake of novel information, integration of this novel information within existing knowledge structures, and the creation of a continuous personal context in which novel information can be integrated and understood. As such, PARCS can explain key characteristics of mental states, such as their temporal and spatial focus (e.g., a focus on the here and now vs. the future; a 1st person vs. a 3rd person perspective. PARCS further relates mental states to brain states and functions, such as activation of the DMN or hemispheric asymmetry in frontal cortical functions. Together, PARCS deepens the understanding of a broad range of mental states, including mindfulness, mind wandering, rumination, autobiographical memory, imagery, and the experience of self.

Some Problems Connected with Reactivity and its Determination

Energy Technology Data Exchange (ETDEWEB)

Boużyk, J.; Chwaszczewski, S. [Institute of Nuclear Research Reactor Physics Dept., Świerk (Poland)

1969-07-01

The applicability of the reactivity concept for subcritical reactor states determination is discussed. It is based on the general properties of the neutron balance equation in a nuclear reactor. It is shown that the reactor fundamental time constants are very useful parameter for reactor state determination. In the frames of the above mentioned theory the classical methods of reactivity determination las rod-drop, source-jerk and source multiplication) are verified. It was found that the neutron pulse method is especially suitable for sophisticated investigation of the reactor kinetic models. Using this technique the difference between static and dynamic reactor parameters can be measured. The study of the neutron counting statistics was found to be very useful for reactor kinetic parameters measurements. Several new techniques (as flash-start and drop-start methods), for reactor noise analysis by the conditional probability methods are presented. For the current noise analysis the analog computer (operating on-line) for autocorrelation function determination was used. Also, the acquisition system for digitalized current noise data and preliminary results of this technique are given. (author)

Tuning of PID controller using optimization techniques for a MIMO process

Science.gov (United States)

Thulasi dharan, S.; Kavyarasan, K.; Bagyaveereswaran, V.

2017-11-01

In this paper, two processes were considered one is Quadruple tank process and the other is CSTR (Continuous Stirred Tank Reactor) process. These are majorly used in many industrial applications for various domains, especially, CSTR in chemical plants.At first mathematical model of both the process is to be done followed by linearization of the system due to MIMO process and controllers are the major part to control the whole process to our desired point as per the applications so the tuning of the controller plays a major role among the whole process. For tuning of parameters we use two optimizations techniques like Particle Swarm Optimization, Genetic Algorithm. The above techniques are majorly used in different applications to obtain which gives the best among all, we use these techniques to obtain the best tuned values among many. Finally, we will compare the performance of the each process with both the techniques.

Diffusive–Dispersive and Reactive Fronts in Porous Media

DEFF Research Database (Denmark)

Haberer, Christina M.; Muniruzzaman, Muhammad; Grathwohl, Peter

2015-01-01

, across the unsaturated–saturated interface, under both conservative and reactive transport conditions. As reactive system we considered the abiotic oxidation of Fe2+ in the presence of O2. We studied the reaction kinetics in batch experiments and its coupling with diffusive and dispersive transport...... processes by means of one-dimensional columns and two-dimensional flow-through experiments, respectively. A noninvasive optode technique was used to track O2 transport into the initially anoxic porous medium at highly resolved spatial and temporal scales. The results show significant differences...

LFC based adaptive PID controller using ANN and ANFIS techniques

Directory of Open Access Journals (Sweden)

Mohamed I. Mosaad

2014-12-01

Full Text Available This paper presents an adaptive PID Load Frequency Control (LFC for power systems using Neuro-Fuzzy Inference Systems (ANFIS and Artificial Neural Networks (ANN oriented by Genetic Algorithm (GA. PID controller parameters are tuned off-line by using GA to minimize integral error square over a wide-range of load variations. The values of PID controller parameters obtained from GA are used to train both ANFIS and ANN. Therefore, the two proposed techniques could, online, tune the PID controller parameters for optimal response at any other load point within the operating range. Testing of the developed techniques shows that the adaptive PID-LFC could preserve optimal performance over the whole loading range. Results signify superiority of ANFIS over ANN in terms of performance measures.

Postocclusive reactive hyperemia in hand-arm vibration syndrome

Directory of Open Access Journals (Sweden)

Zlatka Stoyneva

2016-08-01

Full Text Available Objectives: To assess laser Doppler-recorded postocclusive reactive hyperemic responses in vibration-induced Raynaud’s phenomenon and compare it with primary and secondary to sclerodermy Raynaud’s phenomenon. Material and Methods: Thirty patients with vibration-induced Raynaud’s phenomenon and 30 healthy controls and patients with primary and secondary to sclerodermy Raynaud’s phenomenon were investigated. Fingerpulp skin blood flow was monitored by laser Doppler flowmetry during postocclusive reactive hyperemia test. Results: Lower initial perfusion values were established in all the patients with Raynaud’s phenomenon compared to the healthy controls (p < 0.0001. The postocclusive reactive hyperemic peak was lower in all the Raynaud’s phenomenon groups compared to the controls (p < 0.0001. The postocclusive and basal perfusions were lower in the secondary Raynaud’s phenomenon groups compared to the control and the primary Raynaud’s phenomenon groups (p < 0.0001. The velocities to postocclusive hyperemic peak were lower in all the Raynaud’s phenomenon patients (p < 0.0001, so were in the vibration-induced (p < 0.002 and the sclerodermy Raynaud’s phenomenon (p < 0.004 groups in relation to the primary Raynaud’s phenomenon group. The perfusion values and the velocities were significantly influenced by the initial superficial skin temperatures and perfusions, while the velocities were dependent also on gender, and the hyperemic peak on age. Conclusions: Postocclusive reactive hyperemia is abnormal in all Raynaud’s phenomenon patients. Laser Doppler-recorded reactive hyperemia test contributes to diagnosing Raynaud’s phenomenon and has proved to be valuable for group analysis. The applied method is not sensitive enough to discriminate adequately the type of Raynaud’s phenomenon among individual cases.

Emotional reactivity: Beware its involvement in traffic accidents.

Science.gov (United States)

M'bailara, Katia; Atzeni, Thierry; Contrand, Benjamin; Derguy, Cyrielle; Bouvard, Manuel-Pierre; Lagarde, Emmanuel; Galéra, Cédric

2018-04-01

Reducing risk attributable to traffic accidents is a public health challenge. Research into risk factors in the area is now moving towards identification of the psychological factors involved, particularly emotional states. The aim of this study was to evaluate the link between emotional reactivity and responsibility in road traffic accidents. We hypothesized that the more one's emotional reactivity is disturbed, the greater the likelihood of being responsible for a traffic accident. This case-control study was based on a sample of 955 drivers injured in a motor vehicle crash. Responsibility levels were determined with a standardized method adapted from the quantitative Robertson and Drummer crash responsibility instrument. Emotional reactivity was assessed with the MATHYS. Hierarchical cluster analysis discriminated four distinctive driver's emotional reactivity profiles: basic emotional reactivity (54%), mild emotional hyper-reactivity (29%), emotional hyper-reactivity (11%) and emotional hypo-reactivity (6%). Drivers who demonstrated emotional hypo-reactivity had a 2.3-fold greater risk of being responsible for a traffic accident than those with basic emotional reactivity. Drivers' responsibility in traffic accidents depends on their emotional status. The latter can change the ability of drivers, modifying their behavior and thus increasing their propensity to exhibit risk behavior and to cause traffic accidents. Copyright © 2017 Elsevier B.V. All rights reserved.

Advanced instrumentation and control techniques for nuclear power plants

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu; Makino, Maomi

1989-01-01

Toshiba has been promoting the development and improvement of control and instrumentation (C and I) systems employing the latest technologies, to fulfill the requirements of nuclear power plants for increased reliability, the upgrading of functions, improved maintainability, and reasonable cost. Such development has been systematically performed based on a schematic view of integrated digital control and instrumentation systems, actively adopting state-of-the-art techniques such as the latest man-machine interfaces, digital and optical multiplexing techniques, and artificial intelligence. In addition, comprehensive feedback has been obtained from the accumulation of operating experience. This paper describes the purpose, contents and status of applications of representative newly-developed systems. (author)

Soft Computing Technique and Conventional Controller for Conical Tank Level Control

Directory of Open Access Journals (Sweden)

Sudharsana Vijayan

2016-03-01

Full Text Available In many process industries the control of liquid level is mandatory. But the control of nonlinear process is difficult. Many process industries use conical tanks because of its non linear shape contributes better drainage for solid mixtures, slurries and viscous liquids. So, control of conical tank level is a challenging task due to its non-linearity and continually varying cross-section. This is due to relationship between controlled variable level and manipulated variable flow rate, which has a square root relationship. The main objective is to execute the suitable controller for conical tank system to maintain the desired level. System identification of the non-linear process is done using black box modelling and found to be first order plus dead time (FOPDT model. In this paper it is proposed to obtain the mathematical modelling of a conical tank system and to study the system using block diagram after that soft computing technique like fuzzy and conventional controller is also used for the comparison.

Comparative study between two austenitic steels with the EPR (Electrochemical Potentiokinetic Reactivation) technique

International Nuclear Information System (INIS)

Guillen M, A.N.

1997-01-01

In the mid 19704s, the intergranular corrosion with stress corrosion cracking (IGSCC) have been identified as a greater problem in Boiling Water Reactors BWR in several places of the world. The Electrochemical Potentiokinetic Reactivation - Single Loop (EPR-SL) test and the Double Loop (EPR-DL) test, were developed as methods for measuring the Degree of Sensitization (DOS), show sensitised materials at subject to Intergranular Corrosion. In Mexico, the Laguna Verde4s reactor is BWR type and many of its principal components was built with AISI 304 stainless steels, while that in VVER reactors as well as Juragua4s reactor in Cuba is used 321 Stainless stell in its Russian equivalent designation 08Ch18N10T. In this work, were studied 304 and 08Ch18N10T stainless steels by means of EPR-SL, EPR-DL and ASTM A-262 techniques, they have been found a good correlation for 304 steel but not in 08Ch18N10T steel and was proposed one modification in the criterion by the evaluation on the sensitisation in this steels. Finally, both materials were welded with procedures used in the nuclear industry, by Slow Strain Rate Test (SSRT) to determine the Stress Corrosion Cracking SCC susceptibility, and subsequently the susceptibility to localized corrosion was studied by means of Cyclic Polarization test and the uniform corrosion rate in a solution with chlorides by the Tafel plot, Potentiodynamic Anodic Polarization Resistance. (Author)

Seismic qualification of nuclear control board by using base isolation technique

International Nuclear Information System (INIS)

Koizumi, T.; Tsujiuchi, N.; Fujita, T.

1987-01-01

The purpose is to adopt base isolation technique as a new approach for seismic qualification of nuclear control board. Basic concept of base isolation technique is expressed. Two dimensional linear motion mechanism with pre-tensioned coil springs and some dampers are included in the isolation device. Control board is regarded as a lamped mass system with inertia moment. Fundamental movement of this device and control board is calculated as a non-linear response problems. Fundamental analysis and numerical estimation, experimental investigation has been undertaken using an actual size control board. Sufficient agreement was recognized between experimental results and numerical estimation. (orig./HP)

Glutamine supplementation suppresses herpes simplex virus reactivation.

Science.gov (United States)

Wang, Kening; Hoshino, Yo; Dowdell, Kennichi; Bosch-Marce, Marta; Myers, Timothy G; Sarmiento, Mayra; Pesnicak, Lesley; Krause, Philip R; Cohen, Jeffrey I

2017-06-30

Chronic viral infections are difficult to treat, and new approaches are needed, particularly those aimed at reducing reactivation by enhancing immune responses. Herpes simplex virus (HSV) establishes latency and reactivates frequently, and breakthrough reactivation can occur despite suppressive antiviral therapy. Virus-specific T cells are important to control HSV, and proliferation of activated T cells requires increased metabolism of glutamine. Here, we found that supplementation with oral glutamine reduced virus reactivation in latently HSV-1-infected mice and HSV-2-infected guinea pigs. Transcriptome analysis of trigeminal ganglia from latently HSV-1-infected, glutamine-treated WT mice showed upregulation of several IFN-γ-inducible genes. In contrast to WT mice, supplemental glutamine was ineffective in reducing the rate of HSV-1 reactivation in latently HSV-1-infected IFN-γ-KO mice. Mice treated with glutamine also had higher numbers of HSV-specific IFN-γ-producing CD8 T cells in latently infected ganglia. Thus, glutamine may enhance the IFN-γ-associated immune response and reduce the rate of reactivation of latent virus infection.

WORKABILITY OF A MANAGEMENT CONTROL MODEL IN SERVICE ORGANIZATIONS: A COMPARATIVE STUDY OF REACTIVE, PROACTIVE AND COACTIVE PHILOSOPHIES

Directory of Open Access Journals (Sweden)

Joshua Onome Imoniana

2006-11-01

Full Text Available The main objective of this study was to compare and contrast the three philosophies of management control models in the process of decision-making, namely reactive, proactive and the coactive. Research methodology was based on literature review and descriptive/exploratory approach. Additionally, a survey of 20 service organizations was carried out in order to make the analysis wider-reaching. In order to do that, the following steps were followed: firstly, fundamentals of reactive, proactive and coactive models were highlighted; secondly, management behaviors in the three approaches were compared, with concepts and their practical application being highlighted, thus retrieving managerial relationships in the organization. In so doing, we draw the hypothesis that middle and top managers who adopt control models that are distant from a more coactive one, usually spend a greater number of working hours in problem-solving, leaving little or no time for planning purposes. Finally, for study consolidation purpose, we have adopted qualitative data collection, whereby a content analysis was carried out with the assistance of six categories. Results have shown the need for a change in management paradigms so that firms are not only compared through financial perspectives, without considering the analysis of management control models which, according to this study, directly influence the operational results of the organizations.

KSHV Rta promoter specification and viral reactivation

Directory of Open Access Journals (Sweden)

Jonathan eGuito

2012-02-01

Full Text Available Viruses are obligate intracellular pathogens whose biological success depends upon replication and packaging of viral genomes, and transmission of progeny viruses to new hosts. The biological success of herpesviruses is enhanced by their ability to reproduce their genomes without producing progeny viruses or killing the host cells, a process called latency. Latency permits a herpesvirus to remain undetected in its animal host for decades while maintaining the potential to reactivate, or switch, to a productive life cycle when host conditions are conducive to generating viral progeny. Direct interactions between many host and viral molecules are implicated in controlling herpesviral reactivation, suggesting complex biological networks that control the decision. One viral protein that is necessary and sufficient to switch latent KSHV into the lytic infection cycle is called K-Rta. Rta is a transcriptional activator that specifies promoters by binding direct DNA directly and interacting with cellular proteins. Among these cellular proteins, binding of K-Rta to RBP-Jk is essential for viral reactivation.. In contrast to the canonical model for Notch signaling, RBP-Jk is not uniformly and constitutively bound to the latent KSHV genome, but rather is recruited to DNA by interactions with K-Rta. Stimulation of RBP-Jk DNA binding requires high affinity binding of Rta to repetitive and palindromic CANT DNA repeats in promoters, and formation of ternary complexes with RBP-Jk. However, while K-Rta expression is necessary for initiating KSHV reactivation, K-Rta’s role as the switch is inefficient. Many factors modulate K-Rta’s function, suggesting that KSHV reactivation can be significantly regulated post-Rta expression and challenging the notion that herpesviral reactivation is bistable. This review analyzes rapidly evolving research on KSHV K-Rta to consider the role of K-Rta promoter specification in regulating the progression of KSHV reactivation.

Flexible AC transmission systems modelling and control

CERN Document Server

Zhang, Xiao-Ping; Pal, Bikash

2012-01-01

The extended and revised second edition of this successful monograph presents advanced modeling, analysis and control techniques of Flexible AC Transmission Systems (FACTS). The book covers comprehensively a range of power-system control problems: from steady-state voltage and power flow control, to voltage and reactive power control, to voltage stability control, to small signal stability control using FACTS controllers. In the six years since the first edition of the book has been published research on the FACTS has continued to flourish while renewable energy has developed into a mature and

Reactive Distillation and Air Stripping Processes for Water Recycling and Trace Contaminant Control

Science.gov (United States)

Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

2009-01-01

Reactive distillation designs are considered to reduce the presence of volatile organic compounds in the purified water. Reactive distillation integrates a reactor with a distillation column. A review of the literature in this field has revealed a variety of functional reactive columns in industry. Wastewater may be purified by a combination of a reactor and a distiller (e.g., the EWRS or VPCAR concepts) or, in principle, through a design which integrates the reactor with the distiller. A review of the literature in reactive distillation has identified some different designs in such combinations of reactor and distiller. An evaluation of reactive distillation and reactive air stripping is presented with regards to the reduction of volatile organic compounds in the contaminated water and air. Among the methods presented, an architecture is presented for the evaluation of the simultaneous oxidation of organics in air and water. These and other designs are presented in light of potential improvements in power consumptions and air and water purities for architectures which include catalytic activity integrated into the water processor. In particular, catalytic oxidation of organics may be useful as a tool to remove contaminants that more traditional distillation and/or air stripping columns may not remove. A review of the current leading edge at the commercial level and at the research frontier in catalytically active materials is presented. Themes and directions from the engineering developments in catalyst design are presented conceptually in light of developments in the nanoscale chemistry of a variety of catalyst materials.

Degradation of reactive orange 4 dye using hydrodynamic cavitation based hybrid techniques.

Science.gov (United States)

Gore, Mohan M; Saharan, Virendra Kumar; Pinjari, Dipak V; Chavan, Prakash V; Pandit, Aniruddha B

2014-05-01

In the present work, degradation of reactive orange 4 dye (RO4) has been investigated using hydrodynamic cavitation (HC) and in combination with other AOP's. In the hybrid techniques, combination of hydrodynamic cavitation and other oxidizing agents such as H2O2 and ozone have been used to get the enhanced degradation efficiency through HC device. The hydrodynamic cavitation was first optimized in terms of different operating parameters such as operating inlet pressure, cavitation number and pH of the operating medium to get the maximum degradation of RO4. Following the optimization of HC parameters, the degradation of RO4 was carried out using the combination of HC with H2O2 and ozone. It has been found that the efficiency of the HC can be improved significantly by combining it with H2O2 and ozone. The mineralization rate of RO4 increases considerably with 14.67% mineralization taking place using HC alone increases to 31.90% by combining it with H2O2 and further increases to 76.25% through the combination of HC and ozone. The synergetic coefficient of greater than one for the hybrid processes of HC+H2O2 and HC+Ozone has suggested that the combination of HC with other oxidizing agents is better than the individual processes for the degradation of dye effluent containing RO4. The combination of HC with ozone proves to be the most energy efficient method for the degradation of RO4 as compared to HC alone and the hybrid process of HC and H2O2. Copyright © 2013 Elsevier B.V. All rights reserved.

Substitution of the soluble boron reactivity control system of a pressurized water reactor by gadolinium burnable poisons

International Nuclear Information System (INIS)

Galperin, A.; Segev, M.; Radkowsky, A.

1986-01-01

The results are presented of a research project that is aimed at designing a gadolinium burnable poison (BP) system for complete reactivity control of a pressurized water reactor (PWR) core during the ''equilibrium'' cycle, resulting in the elimination of the soluble boron system, which represents a considerable saving in both capital and operating costs. A flat and strong negative moderator temperature coefficient is assured for a poison-free moderator. The design analysis of a core, heavily loaded with gadolinium BP rods, was based on a BGUCORE neutronic package and cluster model of a fuel assembly. The project objective was achieved by a novel lumped BP rod, designed as an annulus of gadolinium, clad by zirconium, and inserted into vacant guide thimbles of fresh-fuel assemblies. Specific combinations were found for the inner/outer radii of the poison ring, gadolinium densities, and number of rods per assembly, resulting in an almost flat criticality curve during the cycle. A reactivity swing of ≅1% ΔK can be easily controlled by an existing system of control rods. Comparison of the fuel cycle length of a gadolinium-controlled core with that of the reference, soluble, boron-controlled core indicated that there is no penalty due to residual poison at end of life. Unique guidelines for the fuel loading strategy were applied to find a practical fuel-shuffling scheme by which the design and operational constraints of a typical PWR core of current design were satisfied. Several problems should be solved for a practical implementation of the presented design relative to operational and safety requirements of the existing control rod system. Adequate movement of the regulating rods should be determined and shutdown margins of the safety rods should be ascertained. Final judgment of the feasibility of the concept may be made following the solution of these and other regulatory-related issues

Pyrimidine nucleobase radical reactivity in DNA and RNA

Science.gov (United States)

Greenberg, Marc M.

2016-11-01

Nucleobase radicals are major products of the reactions between nucleic acids and hydroxyl radical, which is produced via the indirect effect of ionizing radiation. The nucleobase radicals also result from hydration of cation radicals that are produced via the direct effect of ionizing radiation. The role that nucleobase radicals play in strand scission has been investigated indirectly using ionizing radiation to generate them. More recently, the reactivity of nucleobase radicals resulting from formal hydrogen atom or hydroxyl radical addition to pyrimidines has been studied by independently generating the reactive intermediates via UV-photolysis of synthetic precursors. This approach has provided control over where the reactive intermediates are produced within biopolymers and facilitated studying their reactivity. The contributions to our understanding of pyrimidine nucleobase radical reactivity by this approach are summarized.

Progress report on the k{sub infinity} measurements of HTGR type lattices with the oscillation technique at zero reactivity; Rapport d'advancement sur les mesures de K {sub infinite} des reseaux du type HTGR avec la technique de l'oscillateur a'reactivite' nulle

Energy Technology Data Exchange (ETDEWEB)

NONE

1971-01-15

The principles of measuring k {sub infinity} for a HTGR lattice using the oscillation technique with zero reactivity were already presented at the ''9th reactor physics meeting of countries participating in the Dragon project''. A brief summary of the essential characteristics of the experiment is followed by a status report on present work.

Insect population control by the sterile-male technique

International Nuclear Information System (INIS)

Lindquist, A.W.

1963-01-01

The successful use of the sterile male technique to eradicate the screw worm fly from the Southeastern part of the United States showed that a new biological method using radiation-sterilized insects could not only control but also eradicate harmful insect pests. A panel of experts met at the IAEA in Vienna in October 1962 to discuss the various aspects and applications of this new technique and to assess its usefulness and limitations. This report summarizes the panel proceedings. 42 refs, 18 figs, 1 tab

Insect population control by the sterile-male technique

Energy Technology Data Exchange (ETDEWEB)

Lindquist, A W

1963-10-01

The successful use of the sterile male technique to eradicate the screw worm fly from the Southeastern part of the United States showed that a new biological method using radiation-sterilized insects could not only control but also eradicate harmful insect pests. A panel of experts met at the IAEA in Vienna in October 1962 to discuss the various aspects and applications of this new technique and to assess its usefulness and limitations. This report summarizes the panel proceedings. 42 refs, 18 figs, 1 tab.

A new computational method for reactive power market clearing

International Nuclear Information System (INIS)

Zhang, T.; Elkasrawy, A.; Venkatesh, B.

2009-01-01

After deregulation of electricity markets, ancillary services such as reactive power supply are priced separately. However, unlike real power supply, procedures for costing and pricing reactive power supply are still evolving and spot markets for reactive power do not exist as of now. Further, traditional formulations proposed for clearing reactive power markets use a non-linear mixed integer programming formulation that are difficult to solve. This paper proposes a new reactive power supply market clearing scheme. Novelty of this formulation lies in the pricing scheme that rewards transformers for tap shifting while participating in this market. The proposed model is a non-linear mixed integer challenge. A significant portion of the manuscript is devoted towards the development of a new successive mixed integer linear programming (MILP) technique to solve this formulation. The successive MILP method is computationally robust and fast. The IEEE 6-bus and 300-bus systems are used to test the proposed method. These tests serve to demonstrate computational speed and rigor of the proposed method. (author)

Coupled core criticality calculations with control rods located in the central reflector region

Energy Technology Data Exchange (ETDEWEB)

Sobhy, M [Reactor depatrment, nuclear research center, Inshaas (Egypt)

1995-10-01

The reactivity of a coupled core is controlled by a set of control rods distributed in the central reflector region. The reactor contains two compact cores cooled and moderated by light water. Control rods are designed to have reactivity worths sufficient to start, control and shutdown the coupled system. Each core in a coupled system is in subcritical conditions without any absorber then each core needs to the other core to fulfill nuclear chain reaction and to approach the criticality. In this case, each core is considered clean which is suitable for research reactor with low flux disturbance and better neutron economy, in addition to the advantage of disappearing the cut corner fuel baskets. This facilitate the in core fuel management with identical fuel baskets. Hot spots will disappear. This leads to a good heat transfer process. the excess reactivity and the shutdown margin are calculated for some of reflector as coupling region gives sufficient area for coupled core are calculated cost. The fluctuations of reactivity for coupled core are calculated by noise analysis technique and compared with that for rode core. The results show low reactivity perturbation associated with coupled core.

Assessment of reactivity devices for CANDU-6 with DUPIC fuel

International Nuclear Information System (INIS)

Jeong, Chang Joon; Choi, Hang Bok

1998-01-01

Reactivity device characteristics for a CANDU-6 reactor loaded with DUPIC fuel have been assessed. A transport code WIMS-AECL and a three-dimensional diffusion code RFSP were used for the lattice parameter generation and the core calculation, respectively. Three major reactivity devices have been assessed for their inherent functions. For the zone controller system, damping capability for spatial oscillation was investigated. The restart capability of the adjuster system was investigated. The shim operation and power stepback calculation were also performed to confirm the compatibility of the current adjuster rod system. The mechanical control absorber was assessed for the capability to compensate the temperature reactivity feedback following a power reduction. This study has shown that the current reactivity device systems retain their functions when used in a DUPIC fuel CANDU reactor

Cognitive Impairments in Occupational Burnout – Error Processing and Its Indices of Reactive and Proactive Control

Directory of Open Access Journals (Sweden)

Krystyna Golonka

2017-05-01

Full Text Available The presented study refers to cognitive aspects of burnout as the effects of long-term work-related stress. The purpose of the study was to investigate electrophysiological correlates of burnout to explain the mechanisms of the core burnout symptoms: exhaustion and depersonalization/cynicism. The analyzed error-related electrophysiological markers shed light on impaired cognitive mechanisms and the specific changes in information-processing in burnout. In the EEG study design (N = 80, two components of error-related potential (ERP, error-related negativity (ERN, and error positivity (Pe, were analyzed. In the non-clinical burnout group (N = 40, a significant increase in ERN amplitude and a decrease in Pe amplitude were observed compared to controls (N = 40. Enhanced error detection, indexed by increased ERN amplitude, and diminished response monitoring, indexed by decreased Pe amplitude, reveal emerging cognitive problems in the non-clinical burnout group. Cognitive impairments in burnout subjects relate to both reactive and unconscious (ERN and proactive and conscious (Pe aspects of error processing. The results indicate a stronger ‘reactive control mode’ that can deplete resources for proactive control and the ability to actively maintain goals. The analysis refers to error processing and specific task demands, thus should not be extended to cognitive processes in general. The characteristics of ERP patterns in burnout resemble psychophysiological indexes of anxiety (increased ERN and depressive symptoms (decreased Pe, showing to some extent an overlapping effect of burnout and related symptoms and disorders. The results support the scarce existing data on the psychobiological nature of burnout, while extending and specifying its cognitive characteristics.

Injury incidence, reactivity and ease of handling of horses kept in groups: A matched case control study in four Nordic countries

DEFF Research Database (Denmark)

Keeling, L.J.; Bøe, K.E.; Christensen, Janne Winther

2016-01-01

evaluated. It was hypothesized that a more socially variable group composition has beneficial effects on behaviour, ease of handling and reducing reactivity whereas frequent changes in group composition has negative consequences, resulting in more injuries. We found that differences in treatment effects...... horses from groups and horses’ reactivity to a fearful stimulus. Using a matched case control design, 61 groups of horses were studied in Denmark, Norway, Finland and Sweden. They were allocated into groups of similar or different age and sex or where membership changed regularly or remained stable....... Injuries were recorded before mixing the horses into treatment groups, the day after mixing and four weeks later. Reactivity of horses to a moving novel object and the behaviour of a horse being removed from its group and the reactions of other group members towards this horse and the handler were...

\\mathscr{H}_2 optimal control techniques for resistive wall mode feedback in tokamaks

Science.gov (United States)

Clement, Mitchell; Hanson, Jeremy; Bialek, Jim; Navratil, Gerald

2018-04-01

DIII-D experiments show that a new, advanced algorithm enables resistive wall mode (RWM) stability control in high performance discharges using external coils. DIII-D can excite strong, locked or nearly locked external kink modes whose rotation frequencies and growth rates are on the order of the magnetic flux diffusion time of the vacuum vessel wall. Experiments have shown that modern control techniques like linear quadratic Gaussian (LQG) control require less current than the proportional controller in use at DIII-D when using control coils external to DIII-D’s vacuum vessel. Experiments were conducted to develop control of a rotating n  =  1 perturbation using an LQG controller derived from VALEN and external coils. Feedback using this LQG algorithm outperformed a proportional gain only controller in these perturbation experiments over a range of frequencies. Results from high βN experiments also show that advanced feedback techniques using external control coils may be as effective as internal control coil feedback using classical control techniques.

Novel method to control antenna currents based on theory of characteristic modes

Science.gov (United States)

Elghannai, Ezdeen Ahmed

Characteristic Mode Theory is one of the very few numerical methods that provide a great deal of physical insight because it allows us to determine the natural modes of the radiating structure. The key feature of these modes is that the total induced antenna current, input impedance/admittance and radiation pattern can be expressed as a linear weighted combination of individual modes. Using this decomposition method, it is possible to study the behavior of the individual modes, understand them and therefore control the antennas behavior; in other words, control the currents induced on the antenna structure. This dissertation advances the topic of antenna design by carefully controlling the antenna currents over the desired frequency band to achieve the desired performance specifications for a set of constraints. Here, a systematic method based on the Theory of Characteristic Modes (CM) and lumped reactive loading to achieve the goal of current control is developed. The lumped reactive loads are determined based on the desired behavior of the antenna currents. This technique can also be used to impedance match the antenna to the source/generator connected to it. The technique is much more general than the traditional impedance matching. Generally, the reactive loads that properly control the currents exhibit a combination of Foster and non-Foster behavior. The former can be implemented with lumped passive reactive components, while the latter can be implemented with lumped non-Foster circuits (NFC). The concept of current control is applied to design antennas with a wide band (impedance/pattern) behavior using reactive loads. We successfully applied this novel technique to design multi band and wide band antennas for wireless applications. The technique was developed to match the antenna to resistive and/or complex source impedance and control the radiation pattern at these frequency bands, considering size and volume constraints. A wide band patch antenna was

Measurements of total OH reactivity during PROPHET-AMOS 2016

Science.gov (United States)

Rickly, P.; Sakowski, J.; Bottorff, B.; Lew, M.; Stevens, P. S.; Sklaveniti, S.; Locoge, N.; Dusanter, S.

2017-12-01

As one of the main oxidant in the atmosphere, the hydroxyl radical (OH) initiates the oxidation of volatile organic compounds that can lead to the formation of ozone and secondary organic aerosols. Understanding both the sources and sinks of OH is therefore important to address issues related to air quality and climate change. Measurements of total OH reactivity can provide an important test of our understanding of the OH radical budget. Recent measurements of total reactivity in many environments have been greater than calculated based on the measured concentration of VOCs, suggesting that important OH sinks in these environments are not well characterized. Measurements of total OH reactivity were performed in a forested environment during the PROPHET - AMOS field campaign (Program for Research on Oxidants: PHotochemisty, Emissions, and Transport - Atmospheric Measurements of Oxidants in Summer) using the Comparative Reactivity Method (CRM) and the Total OH Loss Rate Method (TOHLM). The site is characterized by large emissions of isoprene and monoterpenes and low anthropogenic influence. Measurements of total OH reactivity using these two techniques agree to within their respective uncertainties, giving confidence in the measured OH reactivity. In addition, measurements of trace gases (VOCs, NOx, O3) were used to perform a comprehensive apportionment of OH sinks. These measurements are used in a chemical model using the Master Chemical Mechanism to calculate the expected OH reactivity. The results will be compared to previous measurements of total OH reactivity at this site.

Affective and cognitive reactivity to mood induction in chronic depression.

Science.gov (United States)

Guhn, Anne; Sterzer, Philipp; Haack, Friderike H; Köhler, Stephan

2018-03-15

Chronic depression (CD) is strongly associated with childhood maltreatment, which has been proposed to lead to inefficient coping styles that are characterized by abnormal affective responsiveness and dysfunctional cognitive attitudes. However, while this notion forms an important basis for psychotherapeutic strategies in the treatment of CD, there is still little direct empirical evidence for a role of altered affective and cognitive reactivity in CD. The present study therefore experimentally investigated affective and cognitive reactivity to two forms of negative mood induction in CD patients versus a healthy control sample (HC). For the general mood induction procedure, a combination of sad pictures and sad music was used, while for individualized mood induction, negative mood was induced by individualized scripts with autobiographical content. Both experiments included n = 15 CD patients versus n = 15 HC, respectively. Interactions between affective or cognitive reactivity and group were analyzed by repeated measurements ANOVAs. General mood induction neither revealed affective nor cognitive reactivity in the patient group while the control group reported the expected decrease of positive affect [interaction (IA) affective reactivity x group: p = .011, cognitive reactivity x group: n.s.]. In contrast, individualized mood induction specifically increased affective reactivity (IA: p = .037) as well as the amount of dysfunctional cognitions in patients versus controls (IA: p = .014). The experiments were not balanced in a crossover design, causal conclusions are thus limited. Additionally, the differences to non-chronic forms of depression are still outstanding. The results suggest that in patients with CD, specific emotional activation through autobiographical memories is a key factor in dysfunctional coping styles. Psychotherapeutic interventions aimed at modifying affective and cognitive reactivity are thus of high relevance in the treatment of CD. Copyright �

Wind Erosion Processes and Control Techniques in the Sahelian Zone of Niger

NARCIS (Netherlands)

Sterk, G.; Stroosnijder, L.; Raats, P.A.C.

1999-01-01

Wind Erosion Processes and Control Techniques in the Sahelian Zone of Niger G. Sterk, L. Stroosnijder, and P.A.C. Raats Abstract The objective of this paper is to present the main results and conclusions from three years of field research on wind erosion processes and control techniques in the