Discussion of the Investigation Method on the Reaction Kinetics of Metallurgical Reaction Engineering

Science.gov (United States)

Du, Ruiling; Wu, Keng; Zhang, Jiazhi; Zhao, Yong

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed, which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Kinetics of exciplex formation/dissipation in reaction following Weller Scheme II

Science.gov (United States)

Fedorenko, S. G.; Burshtein, A. I.

2014-09-01

Creation of exciplexes from the charged products of photoionization is considered by means of Integral Encounter Theory. The general kinetic equations of such a reaction following the Weller scheme II are developed. The special attention is given to the particular case of irreversible remote ionization of primary excited electron donor. Kinetics of exciplex formation is considered at fast biexponential geminate transformation of exciplexes in cage that gives way to subsequent bulk reaction of equilibrated reaction products controlled by power law recombination of ions. It is shown that the initial geminate stage of exciplex kinetics is observed only in diffusion controlled regime of the reaction and disappears with increasing mobility of ions in passing to kinetic regime. The quantum yield of exciplexes is studied along with their kinetics.

Kinetics of exciplex formation/dissipation in reaction following Weller Scheme II

Energy Technology Data Exchange (ETDEWEB)

Fedorenko, S. G. [Voevodsky Institute of Chemical Kinetics and Combustion, Novosibirsk (Russian Federation); Burshtein, A. I. [Weizmann Institute of Science, 76100, Rehovot (Israel)

2014-09-21

Creation of exciplexes from the charged products of photoionization is considered by means of Integral Encounter Theory. The general kinetic equations of such a reaction following the Weller scheme II are developed. The special attention is given to the particular case of irreversible remote ionization of primary excited electron donor. Kinetics of exciplex formation is considered at fast biexponential geminate transformation of exciplexes in cage that gives way to subsequent bulk reaction of equilibrated reaction products controlled by power law recombination of ions. It is shown that the initial geminate stage of exciplex kinetics is observed only in diffusion controlled regime of the reaction and disappears with increasing mobility of ions in passing to kinetic regime. The quantum yield of exciplexes is studied along with their kinetics.

Kinetics of exciplex formation/dissipation in reaction following Weller Scheme II

International Nuclear Information System (INIS)

Fedorenko, S. G.; Burshtein, A. I.

2014-01-01

Creation of exciplexes from the charged products of photoionization is considered by means of Integral Encounter Theory. The general kinetic equations of such a reaction following the Weller scheme II are developed. The special attention is given to the particular case of irreversible remote ionization of primary excited electron donor. Kinetics of exciplex formation is considered at fast biexponential geminate transformation of exciplexes in cage that gives way to subsequent bulk reaction of equilibrated reaction products controlled by power law recombination of ions. It is shown that the initial geminate stage of exciplex kinetics is observed only in diffusion controlled regime of the reaction and disappears with increasing mobility of ions in passing to kinetic regime. The quantum yield of exciplexes is studied along with their kinetics

Preventing Corrosion by Controlling Cathodic Reaction Kinetics

Science.gov (United States)

2016-03-25

3. DATES COVERED (From - To) 09/23/15 - 04/22/16 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER Preventing Corrosion by Controlling Cathodic Reaction...Preventing corrosion by controlling cathodic reaction kinetics Progress Report for Period: 1 SEP 2015-31 MAR 2016 John Keith Department of...25 March 2016 Preventing corrosion by controlling cathodic reaction kinetics Annual Summary Report: FY16 PI: John Keith, 412-624-7016,jakeith

Spectroscopy and reaction kinetics of HCO

International Nuclear Information System (INIS)

Guo, Yili.

1989-01-01

The high-resolution infrared spectrum of the C-H stretching fundamental of HCO has been studied by means of infrared flash kinetic spectroscopy. HCO was generated by flash photolysis of acetaldehyde or formaldehyde using a 308 nm (XeCl) excimer laser. The transient absorption was probed with an infrared difference frequency laser system. The high resolution spectra obtained were assigned and fitted with rotational, spin-rotational, and centrifugal distortion constants. The ν 1 band origin is 2434.48 cm/sup /minus/1/. New ground state constants have been derived from a least-squares fit combining the ν 1 data with previous microwave and FIR LMR measurements. A new set of spectroscopic constants for the (1, 0, 0) state, the equilibrium rotational constants, and the orientation of the transition dipole moment are also reported. The kinetics and product branching ratios of the HCO + NO 2 reaction have been studied using visible and infrared laser flash kinetic spectroscopy. The rate constant for the disappearance of HCO radical at 296 K is (5.7 +- 0.9) /times/ 10/sup /minus/11/ cm 3 molec/sup /minus/1/ sec/sup /minus/1/, and it is independent of the pressure of SF 6 buffer gas up to 700 torr. Less than 10% of the reaction goes through the most exothermic product channel, HNO + CO 2 . The product channel, H + CO 2 + NO, is responsible for 52% of the reaction. HONO has been observed, though not quantitatively, as a reaction product corresponding to the HONO + CO channel. 51 refs., 21 figs., 8 tabs

Study of kinetics of reaction of lithium deuteride powder with O2, CO2 and water vapor

International Nuclear Information System (INIS)

Li Gan; Lu Guangda; Jing Wenyong; Qin Cheng

2004-01-01

The kinetics of reaction of lithium deuteride powder with O 2 , CO 2 and water vapor is studied. The experimental results show that lithium deuteride reacts with O 2 and CO 2 at very small reaction rate but with water vapor at comparatively larger rate at room temperature (≅28 degree C). The reaction process with water vapor could be described using the unreacted shrinking core model. The second-order kinetics is appropriate for the chemical reaction on the surface of lithium deuteride and reaction rate constant is 0.281 kPa -1 ·min -1

Kinetic study of the annealing reactions in Cu-Ni-Fe alloys

International Nuclear Information System (INIS)

Donoso, E.

2014-01-01

The thermal aging of a Cu-45Ni-4Fe, Cu-34Ni-11Fe and Cu-33Ni-22Fe alloys tempered from 1173 K have been studied from Differential Scanning Calorimetry (DSC) and microhardness measurements. The analysis of DSC curves, from room temperature to 950 K, shows the presence of one exothermic reaction associated to the formation of FeNi 3 phase nucleating from a modulate structure, and one endothermic peak attributed to dissolution of this phase. Kinetic parameters were obtained using the usual Avrami-Erofeev equation, modified Kissinger method and integrated kinetic functions. Microhardness measurements confirmed the formation and dissolution of the FeNi 3 phase. (Author)

Kinetic study on bonding reaction of gelatin with CdS nanopaticles by UV-visible spectroscopy.

Science.gov (United States)

Tang, Shihua; Wang, Baiyang; Li, Youqun

2015-04-15

The chemical kinetics on gelatin-CdS direct conjugates has been systematically investigated as a function of different temperature and reactant concentration (i.e. Cd(2+), S(2-) and gelatin) by UV-visible spectroscopy, for the first time. The nonlinear fitting and the differential method were used to calculate the initial rate based on the absorbance-time data. A double logarithmic linear equation for calculating the rate constant (k) and the reaction order (n) was introduced. The reaction kinetic parameters (n, k, Ea, and Z) and activation thermodynamic parameters (ΔG(≠), ΔH(≠), and ΔS(≠)) were obtained from variable temperature kinetic studies. The overall rate equation allowing evaluation of conditions that provide required reaction rate could be expressed as: r = 1.11 × 10(8) exp(-4971/T)[Cd(2+)][gelatin](0.6)[S(2-)](0.6) (M/S) The calculated values of the reaction rate are well coincide with the experimental results. A suitable kinetic model is also proposed. This work will provide guidance for the rational design of gelatin-directed syntheses of metal sulfide materials, and help to understand the biological effects of nanoparticles at the molecular level. Copyright © 2015 Elsevier B.V. All rights reserved.

Kinetic calorimetry in the study of the mechanism of low-temperature chemical reactions

Science.gov (United States)

Barkalov, I. M.; Kiryukhin, D. P.

Chemical reactions are always followed by a change in the reacting system enthalpy, hence, calorimetry as a method of enthalpy and heat capacity measuring is a universal and, sometimes, even the only possible way of studying chemical reaction kinetics. Throughout its long history, the calorimeter, having preserved the positions of the main method of thermodynamic studies, has conquered a new field of application: that of kinetic study of chemical reactions. The advantages and disadvantages of the kinetic calorimeter are now obvious. First, the advantages are: (1) the possibility of measuring the rate of a chemical reaction without any special requirements being imposed on the reaction medium (solid, viscous, multicomponent systems); (2) the high efficiency: a large volume of kinetic information in one experiment and a non-destructive character of changes; (3) the possibility of measuring directly in the field of ionizing radiation (γ-radiation, accelerated electrons) and light; and (4) recording of the chemical conversion directly at the time of its occurrence. The disadvantages of this method are: (1) the high inertia of standard calorimeter systems (τC⋍102-103S), which restricts the possibilities of studying fast processes; and (2) the complexity of the correct organization of the calorimeter experiment when the parameters of the process are changed (overheating in the sample, conversion of the process to explosive and auto wave regimens). One of the oldest and most universal methods of studying the mechanism of chemical reactions, calorimetry, is now passing through a period of turbulent development due to the advances in electronics and computerization. The wide variety of types of calorimeter set-ups and the large assortment of measurement schemes in the currently described methods complicate the experimental selection of the necessary instrument rather than facilitate it. The basic principles of the method, the types of calorimeters, and the measuring

Configuration of a pulse radiolysis system for the study of gas-phase reactions and kinetic investigations of the reactions of hydroxyl radicals with methyl and ethyl radicals

International Nuclear Information System (INIS)

Fagerstroem, K.

1993-01-01

The work that is presented in this thesis deals with the assembling and testing of a pulse radiolysis system for kinetic studies of gas-phase reactions as well as with the kinetics of the gas-phase reactions of hydroxyl radicals with methyl and ethyl radicals. These radicals are very important as these are formed at an early stage in hydrocarbon combustion processes. The two studied reactions are key reactions in those processes. (6 refs., 4 figs., 2 tabs.)

Reaction kinetics of polybutylene terephthalate polycondensation reaction

NARCIS (Netherlands)

Darda, P. J.; Hogendoorn, J. A.; Versteeg, G. F.; Souren, F.

2005-01-01

The kinetics of the forward polycondensation reaction of polybutylene terephthalate (PBT) has been investigated using thermogravimetric analysis (TGA). PBT - prepolymer with an initial degree of polymerization of 5.5 was used as starting material. The PBT prepolymer was prepared from dimethyl

Study of kinetics and mechanism of diazo compound reactions using nuclear chemical polarization

International Nuclear Information System (INIS)

Gragerov, I.P.; Levit, A.F.; Kiprianova, L.A.; Buchachenko, A.L.; Sterleva, T.G.

1975-01-01

It has been established that at the rate-determining steps of the radical reactions in which aniline interacts with isoamyl nitrite and substituted diazo salts interact with sodium methylate, tertiary fatty amines, or phosphinic acid, no transfer of a single electron occurs. The processes of single electron transfer do not seem to play a decisive role in the kinetics of most transformations of diazo compounds. Chemical nuclear polarization is shown to be suitable for kinetic studies of fast radical processes

Kinetic aspects of the Maillard reaction: a critical review

NARCIS (Netherlands)

Boekel, van M.A.J.S.

2001-01-01

The literature concerning the kinetics of the Maillard reaction was critically discussed according to the initial, intermediate and advanced stages, as this is the way the Maillard reaction is traditionally analysed. For each stage, a division is made between simple kinetics and complex kinetics.

Enzyme-catalyzed and binding reaction kinetics determined by titration calorimetry.

Science.gov (United States)

Hansen, Lee D; Transtrum, Mark K; Quinn, Colette; Demarse, Neil

2016-05-01

Isothermal calorimetry allows monitoring of reaction rates via direct measurement of the rate of heat produced by the reaction. Calorimetry is one of very few techniques that can be used to measure rates without taking a derivative of the primary data. Because heat is a universal indicator of chemical reactions, calorimetry can be used to measure kinetics in opaque solutions, suspensions, and multiple phase systems and does not require chemical labeling. The only significant limitation of calorimetry for kinetic measurements is that the time constant of the reaction must be greater than the time constant of the calorimeter which can range from a few seconds to a few minutes. Calorimetry has the unique ability to provide both kinetic and thermodynamic data. This article describes the calorimetric methodology for determining reaction kinetics and reviews examples from recent literature that demonstrate applications of titration calorimetry to determine kinetics of enzyme-catalyzed and ligand binding reactions. A complete model for the temperature dependence of enzyme activity is presented. A previous method commonly used for blank corrections in determinations of equilibrium constants and enthalpy changes for binding reactions is shown to be subject to significant systematic error. Methods for determination of the kinetics of enzyme-catalyzed reactions and for simultaneous determination of thermodynamics and kinetics of ligand binding reactions are reviewed. Copyright © 2015 Elsevier B.V. All rights reserved.

The renneting of milk : a kinetic study of the enzymic and aggregation reactions

NARCIS (Netherlands)

Hooydonk, van A.C.M.

1987-01-01

The rennet-induced clotting of milk was studied under various conditions. The kinetics of the enzymic and aggregation reactions was analysed separately and, where possible, related to the physico-chemical properties of the casein micelle and its environment.

The effects of important

Deuterium secondary isotope kinetic effects in imine formation reactions

International Nuclear Information System (INIS)

Amaral, L. do; Rossi, M.H.

1986-01-01

The kinetic α-deuterium isotope effects, K D /K H , for reaction mechanisms is studied. The reaction of pH function to m-bromobenzaldehyde, semicarbazide nucleophile, methoxy-amine and hydroxylamine are analysed. (M.J.C.) [pt

Penicillin Hydrolysis: A Kinetic Study of a Multistep, Multiproduct Reaction.

Science.gov (United States)

McCarrick, Thomas A.; McLafferty, Fred W.

1984-01-01

Background, procedures used, and typical results are provided for an experiment in which students carry out the necessary measurements on the acid-catalysis of penicillin in two hours. By applying kinetic theory to the data obtained, the reaction pathways for the hydrolysis of potassium benzyl penicillin are elucidated. (JN)

Optimization and kinetic studies of sea mango (Cerbera odollam) oil for biodiesel production via supercritical reaction

International Nuclear Information System (INIS)

Ang, Gaik Tin; Ooi, San Nee; Tan, Kok Tat; Lee, Keat Teong; Mohamed, Abdul Rahman

2015-01-01

Highlights: • Sea mango oil as feedstock for biodiesel via non-catalytic supercritical reaction. • Extracted sea mango oil with high FFA could produce high yield of FAME. • Employment of Response Surface Methodology for optimization of FAME. • Kinetic study for reversible transesterification and esterification reactions. - Abstract: Sea mango (Cerbera odollam) oil, which is rich in free fatty acids, was utilized to produce fatty acid methyl esters (FAME) via supercritical transesterification reaction. Sea mango oil was extracted from seeds and was subsequently reacted with methanol in a batch-type supercritical reactor. Response surface methodology (RSM) analysis was used to optimize important parameters, including reaction temperature, reaction time and the molar ratio of methanol to oil. The optimum conditions were found as 380 °C, 40 min and 45:1 mol/mol, respectively, to achieve 78% biodiesel content. The first kinetic modelling of FAME production from sea mango oil incorporating reversible transesterification and reversible esterification was verified simultaneously. The kinetic parameters, including reaction rate constants, k, the pre-exponential constant, A, and the activation energy, Ea, for transesterification and esterification were determined using an ordinary differential equation (ODE45) solver. The highest activation energy of 40 kJ/mol and the lowest reaction rate constant of 2.50 × 10 −5 dm 3 /mol s verified that the first stepwise reaction of TG to produce DG was the rate-limiting step

Internal Diffusion-Controlled Enzyme Reaction: The Acetylcholinesterase Kinetics.

Science.gov (United States)

Lee, Sangyun; Kim, Ji-Hyun; Lee, Sangyoub

2012-02-14

Acetylcholinesterase is an enzyme with a very high turnover rate; it quenches the neurotransmitter, acetylcholine, at the synapse. We have investigated the kinetics of the enzyme reaction by calculating the diffusion rate of the substrate molecule along an active site channel inside the enzyme from atomic-level molecular dynamics simulations. In contrast to the previous works, we have found that the internal substrate diffusion is the determinant of the acetylcholinesterase kinetics in the low substrate concentration limit. Our estimate of the overall bimolecular reaction rate constant for the enzyme is in good agreement with the experimental data. In addition, the present calculation provides a reasonable explanation for the effects of the ionic strength of solution and the mutation of surface residues of the enzyme. The study suggests that internal diffusion of the substrate could be a key factor in understanding the kinetics of enzymes of similar characteristics.

Kinetic Studies of Oxidative Coupling of Methane Reaction on Model Catalysts

KAUST Repository

Khan, Abdulaziz M.

2016-01-01

the process to be commercialized despite the fact that great number of attempts to prepare catalysts were conducted so that it can be economically viable. Due to these limitations, understanding the mechanism and kinetics of the reaction can be utilized

Kinetic study of the reaction of uranium with various carbon-containing gases

International Nuclear Information System (INIS)

Feron, G.

1963-09-01

The kinetic study of the reaction U + CO 2 and U + CO has been performed by a thermogravimetric method on a spherical uranium powder, in temperature ranges respectively from 460 to 690 deg. C and from 570 to 850 deg. C. The reaction with carbon dioxide leads to uranium dioxide. A carbon deposition takes place at the same time. The global reactions is the result of two reactions: U + 2 CO 2 → UO 2 + 2 CO U + CO 2 → UO 2 + C The reaction with carbon monoxide leads to a mixture of dioxide UO 2 , dicarbide UC 2 and free carbon. The main reaction can be written. U + CO → 1/2 UO 2 + 1/2 UC 2 The free carbon results of the disproportionation of the carbon monoxide. A remarkable separation of the two phases UO 2 and UC 2 can be observed. A mechanism accounting for the phenomenon has been proposed. The two reactions U + CO 2 and U + CO begin with a long germination period, after which, the reaction velocity seems to be limited in both cases by the ionic diffusion of oxygen through the uranium dioxide. (author) [fr

Struvite Precipitation and Phosphorous Removal from Urine Synthetic Solution: Reaction Kinetic Study

Directory of Open Access Journals (Sweden)

Marwa Saied Shalaby

2015-03-01

Full Text Available Phosphorus, like oil, is a non-renewable resource that must be harvested from finite resources in the earth’s crust. An essential element for life, phosphorus is becoming increasingly scarce, contaminated, and difficult to extract. Struvite or magnesium ammonium phosphate (MgNH4PO4.6H2O is a white, crystalline phosphate mineral that can be used as a bio-available fertilizer. The main objective of this research is to indicate the most important operating parameters affecting struvite precipitation by means of chemical reaction kinetics. The present study explores struvite precipitation by chemical method under different starting molar ratios, pH and SSR. It is shown that an increase of starting Mg: PO4: NH4 with respect to magnesium (1.6:1:1 strongly influences the growth rate of struvite and so the efficiency of the phosphate removal. This was attributed to the effect of magnesium on the struvite solubility product and on the reached supersaturation Super Saturation Ratio at optimum starting molar ratio and pH. It was also shown, by using chemical precipitation method that the determined Super Saturation Ratio (SSR values of struvite, at 8, 8.5, 9, 9.5 and 10 are 1.314, 4.29, 8.89, 9.87 and 14.89 respectively are close to those presented in the literature for different origins of wastewater streams. The results show that SSR , pH, and starting molar ratio strongly influences the kinetics of precipitation and so phosphorous removal to reach 93% removal percent , 5.95 mg/lit as a minimum PO4 remained in solution, and 7.9 gm precipitated struvite from feed synthetic solution of 750 ml . The product was subjected to chemical analysis by means of EDIX-FTIR, SEM and XRD showing conformity with published literature. First-order kinetics was found to be sufficient to describe the rate data. The rates increased with increasing pH and so SSR and the apparent rate constants for the reaction were determined. © 2015 BCREC UNDIP. All rights reserved

Flow chemistry kinetic studies reveal reaction conditions for ready access to unsymmetrical trehalose analogues.

Science.gov (United States)

Patel, Mitul K; Davis, Benjamin G

2010-10-07

Monofunctionalization of trehalose, a widely-found symmetric plant disaccharide, was studied in a microreactor to give valuable kinetic insights that have allowed improvements in desymmetrization yields and the development of a reaction sequence for large scale monofunctionalizations that allow access to probes of trehalose's biological function.

Esterification with ethanol to produce biodiesel from high acidity raw materials. Kinetic studies and analysis of secondary reactions

Energy Technology Data Exchange (ETDEWEB)

Pisarello, M.L.; Dalla Costa, B.; Mendow, G.; Querini, C.A. [Instituto de Investigaciones en Catalisis y Petroquimica (INCAPE)-(FIQ-UNL, CONICET), Santiago del Estero 2654-Santa Fe, S3000AOJ (Argentina)

2010-09-15

In this work, the esterification reaction of free fatty acids (FFA) in sunflower oil, coconut oil and concentrated FFA, with ethanol, methanol and ethanol 96%, using homogeneous acid catalysts to produce biodiesel is studied. Kinetic parameters are estimated with a simplified model, and then used to predict the reaction behavior. Reactions other than the reversible esterification are considered to explain the behavior that this system displays. Such reactions are the triglycerides conversion by acid catalyzed transesterification and hydrolysis. In addition, we include kinetic studies of the reaction that occur between the sulphuric acid and methanol (or ethanol), forming mono and dialkylsulphates. This reaction produces water and consumes methanol (or ethanol), and consequently has a direct impact in the esterification reaction rate and equilibrium conversion. The concentration of sulphuric acid decreases to less than 50% of the initial value due to the reaction with the alcohol. A minimum in the acidity due to the free fatty acids as a function of time was clearly observed during the reaction, which has not been reported earlier. This behavior is related to the consecutive reactions that take place during the esterification of FFA in the presence of triglycerides. The phase separation due to the presence of water, which is generated during the reaction, is also studied. (author)

Kinetics of gaseous uranium hexafluoride reaction with hydrogen chloride

International Nuclear Information System (INIS)

Ezubchenko, A.N.; Ilyukhin, A.I.; Merzlyakov, A.V.

1993-01-01

Kinetics of decrease of concentration of gaseous uranium hexafluoride in reaction with hydrogen chloride at temperatures close to room ones, was investigated by the method of IR spectroscopy. It was established that the process represented the first order reaction by both UF 6 and HCl. Activation energy of the reaction was determined: 7.6 ± 0.7 kcal/mol. Specific feature of reaction kinetics was noted: inversely proportional dependence of effective constant on UF 6 initial pressure. 5 refs., 3 figs

Kinetic concepts of thermally stimulated reactions in solids

Science.gov (United States)

Vyazovkin, Sergey

Historical analysis suggests that the basic kinetic concepts of reactions in solids were inherited from homogeneous kinetics. These concepts rest upon the assumption of a single-step reaction that disagrees with the multiple-step nature of solid-state processes. The inadequate concepts inspire such unjustified anticipations of kinetic analysis as evaluating constant activation energy and/or deriving a single-step reaction mechanism for the overall process. A more adequate concept is that of the effective activation energy, which may vary with temperature and extent of conversion. The adequacy of this concept is illustrated by literature data as well as by experimental data on the thermal dehydration of calcium oxalate monohydrate and thermal decomposition of calcium carbonate, ammonium nitrate and 1,3,5,7- tetranitro-1,3,5,7-tetrazocine.

Kinetics of chemical reactions initiated by hot atoms

International Nuclear Information System (INIS)

Firsova, L.P.

1977-01-01

Modern ideas about kinetics of chemical reactions of hot atoms are generalized. The main points of the phenomenological theories (''kinetic theory'' of Wolfgang-Estrup hot reactions and the theory of ''reactions integral probability'' of Porter) are given. Physico-chemical models of elastic and non-elastic collisions are considered which are used in solving Boltzmann integro-differential equations and stochastic equations in the Porter theory. The principal formulas are given describing probabilities or yields of chemical reactions, initiated with hot atoms, depending on the distribution functions of hot particles with respect to energy. Briefly described are the techniques and the results of applying the phenomenological theories for interpretation of the experimental data obtained during nuclear reactions with hot atoms, photochemical investigations, etc. 96 references are given

Reaction kinetics, reaction products and compressive strength of ternary activators activated slag designed by Taguchi method

NARCIS (Netherlands)

Yuan, B.; Yu, Q.L.; Brouwers, H.J.H.

2015-01-01

This study investigates the reaction kinetics, the reaction products and the compressive strength of slag activated by ternary activators, namely waterglass, sodium hydroxide and sodium carbonate. Nine mixtures are designed by the Taguchi method considering the factors of sodium carbonate content

Kinetic modelling of the Maillard reaction between proteins and sugars

NARCIS (Netherlands)

Brands, C.M.J.

2002-01-01

Keywords: Maillard reaction, sugar isomerisation, kinetics, multiresponse modelling, brown colour formation, lysine damage, mutagenicity, casein, monosaccharides, disaccharides, aldoses, ketoses

The aim of this thesis was to determine the kinetics of the Maillard reaction between

Constrained reaction volume approach for studying chemical kinetics behind reflected shock waves

KAUST Repository

Hanson, Ronald K.; Pang, Genny A.; Chakraborty, Sreyashi; Ren, Wei; Wang, Shengkai; Davidson, David Frank

2013-01-01

We report a constrained-reaction-volume strategy for conducting kinetics experiments behind reflected shock waves, achieved in the present work by staged filling in a shock tube. Using hydrogen-oxygen ignition experiments as an example, we

Kinetics of elementary atom and radical reactions

International Nuclear Information System (INIS)

Gordon, R.J.

1990-06-01

During the past three years we have been working on four problems in the general area of gas phase kinetics and energy transfer of small molecules. These are: (1) measurements of the fine structure populations of ground state oxygen atoms produced in photodissociation reactions; (2) quenching of the Rydberg B ( 1 Σ + ) state of CO; (3) vibrational relaxation of highly excited molecules; and (4) kinetics of hydrogen molecules. The first two topics, which involve transitions between different electronic states of the parent molecule, are a departure from our previous research interests. In the accompanying renewal proposal we discuss plans to pursue these new topics vigorously during the coming year. The third topic is a continuation of our long interest in the energy dependence of the rates laws governing vibrational-to-translational energy transfer of molecules having large initial amounts of vibrational excitation. The final topic is a continuation of our studies of the reaction of O( 3 P) + H 2 . In this work we measured the rate constant for the reaction O( 3 P) with deuterium and also analyzed spectroscopically different sources of vibrationally excited hydrogen for possible future work. We discuss each of these four studies in the following sections

Characterization and kinetic study of Diels-Alder reaction: Detailed study on N-phenylmaleimide and furan based benzoxazine with potential self-healing application

Directory of Open Access Journals (Sweden)

Z. Stirn

2016-07-01

Full Text Available The Diels-Alder reaction between N-phenylmaleimide and benzoxazine bearing furan group was investigated for the purpose of successful appliance of self-healing in benzoxazine polymer networks. The reaction as a function of temperature/time was performed in molten state and in a solution, where also the kinetic study was performed. The Diels-Alder reaction leads to a mixture of two diastereomers: endo presented at lower cyclo-reversion temperature and exo at higher. Therefore, the conversion rates and exo/endo ratio were studied in detail for both systems. For instance, in molten state the Diels-Alder reaction was triggered by the temperature of the melting point at 60 °C with exo/endo ratio preferable to the endo adduct. The study of the kinetics in a solution revealed that the Diels-Alder reaction followed typical bimolecular reversible second-order reaction. The activation energies were close to the previous literature data; 48.4 and 51.9 kJ·mol–1 for Diels-Alder reaction, and 91.0 and 102.3 kJ·mol–1 for retro-Diels-Alder reaction, in acetonitrile and chloroform, respectively. The reaction equilibrium in a solution is much more affected by the retro-Diels-Alder reaction than in a molten state. This study shows detailed investigation of DA reaction and provides beneficial knowledge for further use in self-healing polymer networks.

A kinetic study of the reaction of water vapor and carbon dioxide on uranium

International Nuclear Information System (INIS)

Santon, J.P.

1964-09-01

The kinetic study of the reaction of water vapour and carbon dioxide with uranium has been performed by thermogravimetric methods at temperatures between 160 and 410 deg G in the first case, 350 and 1050 deg C in the second: Three sorts of uranium specimens were used: uranium powder, thin evaporated films, and small spheres obtained from a plasma furnace. The experimental results led in the case of water vapour, to a linear rate of reaction controlled by diffusion at the lower temperatures, and by a surface reaction at the upper ones. In the case of carbon dioxide, a parabolic law has been found, controlled by diffusional processes. (author) [fr

A kinetic study of the redox reactions of complex cyanides of iron, molybdenum and tungsten with compounds of the group VI A elements

International Nuclear Information System (INIS)

Dennis, C.R.

1981-01-01

The kinetic study arises out of the fact that few is known about redox kinetics of complex cyanides of molybdenum and tungsten. The redox kinetics of the complex cyanides of iron with organic and inorganic compounds are well known in organic chemistry. This comparitive study is done to obtain more information on redox reactions of complex cyanides of molybdenum and tungsten considering its greater applicability in organic and inorganic chemistry because of the propitious reduction potential of this complex cyanide in acidic and alkaline mediums. Various redox systems are kinetically investigated regarding the influence of the oxidising agent, reducing agent hydrogen ions and alkaline-metal ions on the reaction rate. A reaction mechanism is proposed for every system

Interactions of nitrite with catalase: Enzyme activity and reaction kinetics studies.

Science.gov (United States)

Krych-Madej, Justyna; Gebicka, Lidia

2017-06-01

Catalase, a heme enzyme, which catalyzes decomposition of hydrogen peroxide to water and molecular oxygen, is one of the main enzymes of the antioxidant defense system of the cell. Nitrite, used as a food preservative has long been regarded as a harmful compound due to its ability to form carcinogenic nitrosamines. Recently, much evidence has been presented that nitrite plays a protective role as a nitric oxide donor under hypoxic conditions. In this work the effect of nitrite on the catalytic reactions of catalase was studied. Catalase was inhibited by nitrite, and this process was pH-dependent. IC 50 values varied from about 1μM at pH5.0 to about 150μM of nitrite at pH7.4. The presence of chloride significantly enhanced nitrite-induced catalase inhibition, in agreement with earlier observations. The kinetics of the reactions of nitrite with ferric catalase, its redox intermediate, Compound I, and catalase inactive form, Compound II, was also studied. Possible mechanisms of nitrite-induced catalase inhibition are analyzed and the biological consequences of the reactions of catalase with nitrite are discussed. Copyright © 2017 Elsevier Inc. All rights reserved.

Constrained reaction volume approach for studying chemical kinetics behind reflected shock waves

KAUST Repository

Hanson, Ronald K.

2013-09-01

We report a constrained-reaction-volume strategy for conducting kinetics experiments behind reflected shock waves, achieved in the present work by staged filling in a shock tube. Using hydrogen-oxygen ignition experiments as an example, we demonstrate that this strategy eliminates the possibility of non-localized (remote) ignition in shock tubes. Furthermore, we show that this same strategy can also effectively eliminate or minimize pressure changes due to combustion heat release, thereby enabling quantitative modeling of the kinetics throughout the combustion event using a simple assumption of specified pressure and enthalpy. We measure temperature and OH radical time-histories during ethylene-oxygen combustion behind reflected shock waves in a constrained reaction volume and verify that the results can be accurately modeled using a detailed mechanism and a specified pressure and enthalpy constraint. © 2013 The Combustion Institute.

Studies on the ruthenium complexes. IX. Kinetic studies on the deaquation-anation reaction of aquapentaammineruthenium(III) complexes

Energy Technology Data Exchange (ETDEWEB)

Ohyoshi, A; Hiraki, S I; Odate, T; Kohata, S; Oda, J [Kumamoto Univ. (Japan). Faculty of Engineering

1975-01-01

The deaquation-anation reaction of (Ru(OH/sub 2/)(NH/sub 3/)/sub 5/)X/sub 3/-type complexes in the solid state, as shown by the (Ru(OH/sub 2/)(NH/sub 3/)/sub 5/)X/sub 3/(s)..-->..(RuX(NH/sub 3/)/sub 5/)X/sub 2/(s)+H/sub 2/O(g) equation, where X is Cl, Br, I, and NO/sub 3/ respectively, was kinetically studied by means of thermogravimetry (TG) along with differential thermal analysis (DTA). The activation energy and entropy in the reaction process (Esub(a) kcal/mol, ..delta..S c.u.) are, respectively, found by isothermal kinetic study to be (22.7, - 7.1) for the chloride, (23.4, - 5.2) for the bromide, (26.7, 5.8) for the iodide, and (19.3 - 15.9) for the nitrate. The reaction seems to proceed through the following two steps, except in the case of the iodide: (Ru(OH/sub 2/)(NH/sub 3/)/sub 5/)X/sub 3/..-->..(RuX(OH/sub 2/)(NH/sub 3/)/sub 5/)X/sub 2/..-->..(RuX(NH/sub 3/)/sub 5/)X/sub 2/+H/sub 2/O. The first step is regarded as the rate-determining one.

Kinetics of ion/molecule reactions in Xe++acteone system

International Nuclear Information System (INIS)

Vinogradov, P.S.; Misharin, A.S.

2002-01-01

A reaction of Xe+ ion with acetone and subsequent transformations of the product ions at a buffer gas pressure (He) of 1.1 Torr were studied by the flow reactor technique mass spectrometry. A kinetic scheme describing the evolution of the ionic composition has been determined. The rate constants of the key reactions involved in the scheme have been evaluated. A channel of the production of acetone cation in A state in a charge transfer reaction was observed. A production of slowly reacting isomer of the acetone cation in secondary reactions was detected. Its product in the reaction with acetone is the 'nonprotonated dimer'. The kinetics of the production of ternary ions - ( CH 3 CO + CH 3 COCH 3 )(m/e=101), CH 3 COCH 3 H + (m/e=59) as well as the production of ions of the fourth generation ( CH 3 CO + (CH 3 COCH 3 ) 2 ) (m/e=159) and (CH 3 COCH 3 ) 2 H + was observed. CH 3 CO + ion (m/e=43) was found as the main reaction product. The main pathways scheme of ionic transformations is shown. (nevyjel)

Mechanistic rationalization of unusual sigmoidal kinetic profiles in the Machetti-De Sarlo cycloaddition reaction.

Science.gov (United States)

Mower, Matthew P; Blackmond, Donna G

2015-02-18

Unusual sigmoidal kinetic profiles in the Machetti-De Sarlo base-catalyzed 1,3-dipolar cycloaddition of acrylamide to N-methylnitroacetamide are rationalized by detailed in situ kinetic analysis. A dual role is uncovered in which a substrate acts as a precursor to catalyze its own reaction. Such kinetic studies provide a general protocol for distinguishing among different mechanistic origins of induction periods in complex organic reactions.

Bayesian experts in exploring reaction kinetics of transcription circuits.

Science.gov (United States)

Yoshida, Ryo; Saito, Masaya M; Nagao, Hiromichi; Higuchi, Tomoyuki

2010-09-15

Biochemical reactions in cells are made of several types of biological circuits. In current systems biology, making differential equation (DE) models simulatable in silico has been an appealing, general approach to uncover a complex world of biochemical reaction dynamics. Despite of a need for simulation-aided studies, our research field has yet provided no clear answers: how to specify kinetic values in models that are difficult to measure from experimental/theoretical analyses on biochemical kinetics. We present a novel non-parametric Bayesian approach to this problem. The key idea lies in the development of a Dirichlet process (DP) prior distribution, called Bayesian experts, which reflects substantive knowledge on reaction mechanisms inherent in given models and experimentally observable kinetic evidences to the subsequent parameter search. The DP prior identifies significant local regions of unknown parameter space before proceeding to the posterior analyses. This article reports that a Bayesian expert-inducing stochastic search can effectively explore unknown parameters of in silico transcription circuits such that solutions of DEs reproduce transcriptomic time course profiles. A sample source code is available at the URL http://daweb.ism.ac.jp/~yoshidar/lisdas/.

A study of redox kinetic in silicate melt; Etude cinetique des reactions d'oxydoreduction dans les silicates

Energy Technology Data Exchange (ETDEWEB)

Magnien, V

2005-12-15

The aim of this thesis is to understand better iron redox reactions and mechanisms in silicate glasses and melts. Particular interest has been paid to the influence of temperature and chemical composition. For this purpose, the influence of alkali element content, iron content and network formers on the kinetics of redox reactions has been determined through XANES and Raman spectroscopy experiments performed either near the glass transition or above the liquidus temperature. As a complement, electrical conductivity and RBS spectroscopy experiments have been made to characterize the diffusivity of the species that transport electrical charges and the reaction morphology, respectively. Temperature and composition variations can induce changes in the dominating redox mechanism. At a given temperature, the parameters that exert the strongest influence on redox mechanisms are the presence or lack of divalent cations and the existing decoupling between the mobility of network former and modifier elements. Near Tg, the diffusion of divalent cations, when present in the melt, controls the kinetics of iron redox reactions along with a flux of electron holes. Composition, through the degree of polymerization and the silicate network structure, influences the kinetics and the nature of the involved cations, but not the mechanisms of the reaction. Without alkaline earth elements, the kinetics of redox reactions are controlled by the diffusion of oxygen species. With increasing temperatures, the diffusivities of all ionic species tend to become similar. The decoupling between ionic fluxes then is reduced so that several mechanisms become kinetically equivalent and can thus coexist. (author)

Reaction kinetics of oxygen on single-phase alloys, oxidation of nickel and niobium alloys

International Nuclear Information System (INIS)

Lalauze, Rene

1973-01-01

This research thesis first addresses the reaction kinetics of oxygen on alloys. It presents some generalities on heterogeneous reactions (conventional theory, theory of jumps), discusses the core reaction (with the influence of pressure), discusses the influence of metal self-diffusion on metal oxidation kinetics (equilibrium conditions at the interface, hybrid diffusion regime), reports the application of the hybrid diffusion model to the study of selective oxidation of alloys (Wagner model, hybrid diffusion model) and the study of the oxidation kinetics of an alloy forming a solid solution of two oxides. The second part reports the investigation of the oxidation of single phase nickel and niobium alloys (phase α, β and γ)

Reaction kinetics of metal deposition via surface limited red-ox replacement of underpotentially deposited metal monolayers

International Nuclear Information System (INIS)

Gokcen, Dincer; Bae, Sang-Eun; Brankovic, Stanko R.

2011-01-01

The study of the kinetics of metal deposition via surface limited red-ox replacement of underpotentially deposited metal monolayers is presented. The model system was Pt submonolayer deposition on Au(1 1 1) via red-ox replacement of Pb and Cu UPD monolayers on Au(1 1 1). The kinetics of a single replacement reaction was studied using the formalism of the comprehensive analytical model developed to fit the open circuit potential transients from deposition experiments. The practical reaction kinetics parameters like reaction half life, reaction order and reaction rate constant are determined and discussed with their relevance to design and control of deposition experiments. The effects of transport limitation and the role of the anions/electrolyte on deposition kinetics are investigated and their significance to design of effective deposition process is discussed.

Kinetics Analysis of Synthesis Reaction of Struvite With Air-Flow Continous Vertical Reactors

Science.gov (United States)

Edahwati, L.; Sutiyono, S.; Muryanto, S.; Jamari, J.; Bayuseno, dan A. P.

2018-01-01

Kinetics reaction is a knowledge about a rate of chemical reaction. The differential of the reaction rate can be determined from the reactant material or the formed material. The reaction mechanism of a reactor may include a stage of reaction occurring sequentially during the process of converting the reactants into products. In the determination of reaction kinetics, the order of reaction and the rate constant reaction must be recognized. This study was carried out using air as a stirrer as a medium in the vertical reactor for crystallization of struvite. Stirring is one of the important aspects in struvite crystallization process. Struvite crystals or magnesium ammonium phosphate hexahydrates (MgNH4PO4·6H2O) is commonly formed in reversible reactions and can be generated as an orthorhombic crystal. Air is selected as a stirrer on the existing flow pattern in the reactor determining the reaction kinetics of the crystal from the solution. The experimental study was conducted by mixing an equimolar solution of 0.03 M NH4OH, MgCl2 and H3PO4 with a ratio of 1: 1: 1. The crystallization process of the mixed solution was observed in an inside reactor at the flow rate ranges of 16-38 ml/min and the temperature of 30°C was selected in the study. The air inlet rate was kept constant at 0.25 liters/min. The pH solution was adjusted to be 8, 9 and 10 by dropping wisely of 1 N KOH solution. The crystallization kinetics was examined until the steady state of the reaction was reached. The precipitates were filtered and dried at a temperature for subsequent material characterization, including Scanning Electron Microscope (SEM) and XRD (X-Ray diffraction) method. The results show that higher flow rate leads to less mass of struvite.

SABIO-RK: A data warehouse for biochemical reactions and their kinetics

Directory of Open Access Journals (Sweden)

Krebs Olga

2007-03-01

Full Text Available Systems biology is an emerging field that aims at obtaining a system-level understanding of biological processes. The modelling and simulation of networks of biochemical reactions have great and promising application potential but require reliable kinetic data. In order to support the systems biology community with such data we have developed SABIO-RK (System for the Analysis of Biochemical Pathways - Reaction Kinetics, a curated database with information about biochemical reactions and their kinetic properties, which allows researchers to obtain and compare kinetic data and to integrate them into models of biochemical networks. SABIO-RK is freely available for academic use at http://sabio.villa-bosch.de/SABIORK/.

A reaction-based paradigm to model reactive chemical transport in groundwater with general kinetic and equilibrium reactions

International Nuclear Information System (INIS)

Zhang, Fan; Yeh, Gour-Tsyh; Parker, Jack C.; Brooks, Scott C; Pace, Molly; Kim, Young Jin; Jardine, Philip M.; Watson, David B.

2007-01-01

This paper presents a reaction-based water quality transport model in subsurface flow systems. Transport of chemical species with a variety of chemical and physical processes is mathematically described by M. partial differential equations (PDEs). Decomposition via Gauss-Jordan column reduction of the reaction network transforms M. species reactive transport equations into two sets of equations: a set of thermodynamic equilibrium equations representing NE equilibrium reactions and a set of reactive transport equations of M-NE kinetic-variables involving no equilibrium reactions (a kinetic-variable is a linear combination of species). The elimination of equilibrium reactions from reactive transport equations allows robust and efficient numerical integration. The model solves the PDEs of kinetic-variables rather than individual chemical species, which reduces the number of reactive transport equations and simplifies the reaction terms in the equations. A variety of numerical methods are investigated for solving the coupled transport and reaction equations. Simulation comparisons with exact solutions were performed to verify numerical accuracy and assess the effectiveness of various numerical strategies to deal with different application circumstances. Two validation examples involving simulations of uranium transport in soil columns are presented to evaluate the ability of the model to simulate reactive transport with complex reaction networks involving both kinetic and equilibrium reactions

A reaction-based paradigm to model reactive chemical transport in groundwater with general kinetic and equilibrium reactions.

Science.gov (United States)

Zhang, Fan; Yeh, Gour-Tsyh; Parker, Jack C; Brooks, Scott C; Pace, Molly N; Kim, Young-Jin; Jardine, Philip M; Watson, David B

2007-06-16

This paper presents a reaction-based water quality transport model in subsurface flow systems. Transport of chemical species with a variety of chemical and physical processes is mathematically described by M partial differential equations (PDEs). Decomposition via Gauss-Jordan column reduction of the reaction network transforms M species reactive transport equations into two sets of equations: a set of thermodynamic equilibrium equations representing N(E) equilibrium reactions and a set of reactive transport equations of M-N(E) kinetic-variables involving no equilibrium reactions (a kinetic-variable is a linear combination of species). The elimination of equilibrium reactions from reactive transport equations allows robust and efficient numerical integration. The model solves the PDEs of kinetic-variables rather than individual chemical species, which reduces the number of reactive transport equations and simplifies the reaction terms in the equations. A variety of numerical methods are investigated for solving the coupled transport and reaction equations. Simulation comparisons with exact solutions were performed to verify numerical accuracy and assess the effectiveness of various numerical strategies to deal with different application circumstances. Two validation examples involving simulations of uranium transport in soil columns are presented to evaluate the ability of the model to simulate reactive transport with complex reaction networks involving both kinetic and equilibrium reactions.

Understanding Chemical Reaction Kinetics and Equilibrium with Interlocking Building Blocks

Science.gov (United States)

Cloonan, Carrie A.; Nichol, Carolyn A.; Hutchinson, John S.

2011-01-01

Chemical reaction kinetics and equilibrium are essential core concepts of chemistry but are challenging topics for many students, both at the high school and undergraduate university level. Visualization at the molecular level is valuable to aid understanding of reaction kinetics and equilibrium. This activity provides a discovery-based method to…

Kinetics and Mechanisms of Calcite Reactions with Saline Waters

Energy Technology Data Exchange (ETDEWEB)

Gorman, Brian P [Colorado School of Mines, Golden, CO (United States)

2015-09-02

Project Description: The general objective of the proposed research is to determine the kinetics and mechanisms of calcite reactions with saline waters over a wide range of saline water composition, pCO₂, and modest ranges in T and P. This will be accomplished by studying both reaction rates and solubility from changes in solution chemistry, and making nanoscale observations of calcite precipitate surface morphology and composition at the micro-to-nano-scale to provide an understanding of controlling reaction mechanisms and pathways. The specific objectives necessary to reach the general objective are: a) determination of how pCO₂, Ca²⁺, ionic strength and “foreign” ions influence reaction rates; and b) investigate the influence of these parameters on apparent kinetic solubility from dissolution and precipitation reactions. This information will clearly be central to the construction of reliable reaction-transport models to predict reservoir and formation response to increased CO₂ in saline waters. This program was initially collaborative with John Morse at Texas A&M, however his passing shortly after the beginning of this program resulted in abbreviated research time and effort. Summary of Results: Early studies using electron microscopy and spectroscopy indicated that carbonate precipitation from natural seawater (NSW) conditions onto aragonite substrates was mediated by a surface amorphous calcium carbonate layer. It was hypothesized that this ACC layer (observed after < 5days reaction time) was responsible for the abnormal reaction kinetics and also served as a metastable seed layer for growth of epitaxial aragonite. Further studies of the ACC formation mechanism indicated a strong dependence on the Mg concentration in solution. Subsequent studies at shorter times (10 hrs) on calcite substrates and in a wide range of supersaturation conditions did not indicate any ACC layer. Instead, an epitaxial layer by layer

Kinetics of Single-Enzyme Reactions on Vesicles: Role of Substrate Aggregation

Science.gov (United States)

Zhdanov, Vladimir P.

2015-03-01

Enzymatic reactions occurring in vivo on lipid membranes can be influenced by various factors including macromolecular crowding in general and substrate aggregation in particular. In academic studies, the role of these factors can experimentally be clarified by tracking single-enzyme kinetics occurring on individual lipid vesicles. To extend the conceptual basis for such experiments, we analyze herein the corresponding kinetics mathematically with emphasis on the role of substrate aggregation. In general, the aggregation may occur on different length scales. Small aggregates may e.g. contain a few proteins or peptides while large aggregates may be mesoscopic as in the case of lipid domains which can be formed in the membranes composed of different lipids. We present a kinetic model describing comprehensively the effect of aggregation of the former type on the dependence of the reaction rate on substrate membrane concentration. The results obtained with physically reasonable parameters indicate that the aggregation-related deviations from the conventional Michaelis-Menten kinetics may be appreciable. Special Issue Comments: This theoretical article is focused on single-enzyme reactions occurring in parallel with substrate aggregation on individual vesicles. This subject is related to a few Special Issue articles concerning enzyme dynamics6,7 and function8 and mathematical aspects of stochastic kinetics.9

Analysis of kinetic reaction mechanisms

CERN Document Server

Turányi, Tamás

2014-01-01

Chemical processes in many fields of science and technology, including combustion, atmospheric chemistry, environmental modelling, process engineering, and systems biology, can be described by detailed reaction mechanisms consisting of numerous reaction steps. This book describes methods for the analysis of reaction mechanisms that are applicable in all these fields. Topics addressed include: how sensitivity and uncertainty analyses allow the calculation of the overall uncertainty of simulation results and the identification of the most important input parameters, the ways in which mechanisms can be reduced without losing important kinetic and dynamic detail, and the application of reduced models for more accurate engineering optimizations. This monograph is invaluable for researchers and engineers dealing with detailed reaction mechanisms, but is also useful for graduate students of related courses in chemistry, mechanical engineering, energy and environmental science and biology.

Comparative study on ion-isotopic exchange reaction kinetics by application of tracer technique

International Nuclear Information System (INIS)

Lokhande, R.S.; Singare, P.U.

2007-01-01

The radioactive isotopes 131 I and 82 Br were used to trace the ion-isotopic exchange reactions using industrial grade ion exchange resins Amberlite IRA-400. The experiments were performed to understand the effect of temperature and concentration of ionic solution on kinetics of exchange reactions. Both the exchange reactions were greatly influenced by rise in temperature, which result in higher percentage of ions exchanged. For bromide ion-isotopic exchange reactions, the calculated values of specific reaction rate/min -1 , and amount of ions exchanged/mmol were obtained higher than that for iodide ion-isotopic exchange reactions under identical experimental conditions. The observed variation in the results for two ion-isotopic exchange reactions was due to the difference in the ionic size of bromide and iodide ions. (orig.)

Application of adjustable pulse lasers to studying rapid reaction kinetics of excited lanthanide complexing

Energy Technology Data Exchange (ETDEWEB)

Gruzdev, V.P. (Gosudarstvennyj Opticheskij Inst., Leningrad (USSR))

1983-12-01

Using some europium (3) ion complexes new possibilities to be opened by application of adjustable pulse lasers for studying rapid reactions of electron-excited metal ion complexing are demonstrated. The 6Zh rhodamine pulse laser is used as a source of nonequilibrium photoexcitation of an array of Eu/sup 3 +/ complexes in the luminescent kinetic spectroscopy method. The following results are obtained: for the first time the rate of reaction of acetate ion substitution for water molecules of an excited (/sup 5/D/sub 0/) ion of Eu/sup 3 +/ was measured to be (0.7+-0.2)x10/sup 7/ s/sup -1/; using direct experiments the lower limit for the rate of transition of one isomeric form of the excited Eu x EDTA complex into another one in an aqueous solution is determined to be 5x10/sup 5/ s/sup -1/ at 295 K; the kinetics of the excitation energy migration beteen aqueous solvates of Eu/sup 3 +/ and EuxEDTA complexes is investigated.

Rate kernel theory for pseudo-first-order kinetics of diffusion-influenced reactions and application to fluorescence quenching kinetics.

Science.gov (United States)

Yang, Mino

2007-06-07

Theoretical foundation of rate kernel equation approaches for diffusion-influenced chemical reactions is presented and applied to explain the kinetics of fluorescence quenching reactions. A many-body master equation is constructed by introducing stochastic terms, which characterize the rates of chemical reactions, into the many-body Smoluchowski equation. A Langevin-type of memory equation for the density fields of reactants evolving under the influence of time-independent perturbation is derived. This equation should be useful in predicting the time evolution of reactant concentrations approaching the steady state attained by the perturbation as well as the steady-state concentrations. The dynamics of fluctuation occurring in equilibrium state can be predicted by the memory equation by turning the perturbation off and consequently may be useful in obtaining the linear response to a time-dependent perturbation. It is found that unimolecular decay processes including the time-independent perturbation can be incorporated into bimolecular reaction kinetics as a Laplace transform variable. As a result, a theory for bimolecular reactions along with the unimolecular process turned off is sufficient to predict overall reaction kinetics including the effects of unimolecular reactions and perturbation. As the present formulation is applied to steady-state kinetics of fluorescence quenching reactions, the exact relation between fluorophore concentrations and the intensity of excitation light is derived.

Formation kinetics of gemfibrozil chlorination reaction products: analysis and application.

Science.gov (United States)

Krkosek, Wendy H; Peldszus, Sigrid; Huck, Peter M; Gagnon, Graham A

2014-07-01

Aqueous chlorination kinetics of the lipid regulator gemfibrozil and the formation of reaction products were investigated in deionized water over the pH range 3 to 9, and in two wastewater matrices. Chlorine oxidation of gemfibrozil was found to be highly dependent on pH. No statistically significant degradation of gemfibrozil was observed at pH values greater than 7. Gemfibrozil oxidation between pH 4 and 7 was best represented by first order kinetics. At pH 3, formation of three reaction products was observed. 4'-C1Gem was the only reaction product formed from pH 4-7 and was modeled with zero order kinetics. Chlorine oxidation of gemfibrozil in two wastewater matrices followed second order kinetics. 4'-C1Gem was only formed in wastewater with pH below 7. Deionized water rate kinetic models were applied to two wastewater effluents with gemfibrozil concentrations reported in literature in order to calculate potential mass loading rates of 4'C1Gem to the receiving water.

A Kinetic Study of the Gas-Phase Reaction of OH with Br2

Science.gov (United States)

Bryukov, Mikhail G.; Dellinger, Barry; Knyazev, Vadim D.

2011-01-01

An experimental, temperature-dependent kinetic study of the gas-phase reaction of the hydroxyl radical with molecular bromine (reaction 1) has been performed using a pulsed laser photolysis/pulsed-laser-induced fluorescence technique over a wide temperature range of 297 – 766 K, and at pressures between 6.68 and 40.29 kPa of helium. The experimental rate coefficients for reaction 1 demonstrate no correlation with pressure and exhibit a negative temperature dependence with a slight negative curvature in the Arrhenius plot. A non-linear least-squares fit with two floating parameters of the temperature dependent k1(T) data set using an equation of the form k1(T) = ATn yields the recommended expression k1(T) = 1.85×10−9T − 0.66 cm3 molecule−1 s−1 for the temperature dependence of the reaction 1 rate coefficient. The potential energy surface (PES) of reaction 1 was investigated using quantum chemistry methods. The reaction proceeds through formation of a weakly bound OH···Br2 complex and a PES saddle point with an energy below that of the reactants. Temperature dependence of the reaction rate coefficient was modeled using the RRKM method on the basis of the calculated PES. PMID:16854030

Kinetics of subdiffusion-assisted reactions: non-Markovian stochastic Liouville equation approach

International Nuclear Information System (INIS)

Shushin, A I

2005-01-01

Anomalous specific features of the kinetics of subdiffusion-assisted bimolecular reactions (time-dependence, dependence on parameters of systems, etc) are analysed in detail with the use of the non-Markovian stochastic Liouville equation (SLE), which has been recently derived within the continuous-time random-walk (CTRW) approach. In the CTRW approach, subdiffusive motion of particles is modelled by jumps whose onset probability distribution function is of a long-tailed form. The non-Markovian SLE allows for rigorous describing of some peculiarities of these reactions; for example, very slow long-time behaviour of the kinetics, non-analytical dependence of the reaction rate on the reactivity of particles, strong manifestation of fluctuation kinetics showing itself in very slowly decreasing behaviour of the kinetics at very long times, etc

A study of redox kinetic in silicate melt; Etude cinetique des reactions d'oxydoreduction dans les silicates

Energy Technology Data Exchange (ETDEWEB)

Magnien, V

2005-12-15

The aim of this thesis is to understand better iron redox reactions and mechanisms in silicate glasses and melts. Particular interest has been paid to the influence of temperature and chemical composition. For this purpose, the influence of alkali element content, iron content and network formers on the kinetics of redox reactions has been determined through XANES and Raman spectroscopy experiments performed either near the glass transition or above the liquidus temperature. As a complement, electrical conductivity and RBS spectroscopy experiments have been made to characterize the diffusivity of the species that transport electrical charges and the reaction morphology, respectively. Temperature and composition variations can induce changes in the dominating redox mechanism. At a given temperature, the parameters that exert the strongest influence on redox mechanisms are the presence or lack of divalent cations and the existing decoupling between the mobility of network former and modifier elements. Near Tg, the diffusion of divalent cations, when present in the melt, controls the kinetics of iron redox reactions along with a flux of electron holes. Composition, through the degree of polymerization and the silicate network structure, influences the kinetics and the nature of the involved cations, but not the mechanisms of the reaction. Without alkaline earth elements, the kinetics of redox reactions are controlled by the diffusion of oxygen species. With increasing temperatures, the diffusivities of all ionic species tend to become similar. The decoupling between ionic fluxes then is reduced so that several mechanisms become kinetically equivalent and can thus coexist. (author)

Kinetic Monte Carlo studies of the reaction kinetics of crystal defects that diffuse one-dimensionally with occasional transverse migration

DEFF Research Database (Denmark)

Heinisch, H.L.; Trinkaus, H.; Singh, Bachu Narain

2007-01-01

The reaction kinetics of the various species of mobile defects in irradiated materials are crucially dependent on the dimensionality of their migration. Sink strengths for one-dimensionally (1D) gliding interstitial loops undergoing occasional direction changes have been described analytically...

Kinetic modeling of reactions in Foods

NARCIS (Netherlands)

Boekel, van M.A.J.S.

2008-01-01

The level of quality that food maintains as it travels down the production-to-consumption path is largely determined by the chemical, biochemical, physical, and microbiological changes that take place during its processing and storage. Kinetic Modeling of Reactions in Foods demonstrates how to

Kinetics of the Coupled Gas-Iron Reactions Involving Silicon and ...

African Journals Online (AJOL)

The kinetic study of coupled gas-iron reactions at 15600 has been carried out for the system involving liquid iron containing carbon and silicon and a gas phase consisting carbon monoxide, silicon monoxide and carbon dioxide. The coupled reactions are: (1) 200(g) = CO2 + C. (2) SiO (g) + CO (g) = Si ¸ CO (g). (3) SiO (g) + ...

Kinetics and mechanistic study of n-alkane hydroisomerization reaction on Pt-doped γ-alumina catalyst

Directory of Open Access Journals (Sweden)

Abhishek Dhar

2017-12-01

Full Text Available The catalysts γ-alumina (GA, the reference catalyst and Pt doped γ-alumina (PGA-s were synthesized using a simple sol-gel technique, in which at first preparation of porous base (GA, then impregnation of platinum salt over the base and finally reduction of platinum in the surface of the support were done. These catalysts prepared in different mole ratios of Pt:Al as 2:1, 1:1 and 1:2 are named as PGA-1, PGA-2 and PGA-3 respectively. The isomerization of n-alkanes (n-hexane, n-heptane and n-octane were investigated over the synthesized catalysts. The 2-methyl pentane (2-MP, 2,2-dimethyl pentane (2,2-DMP and 2,3-dimethyl hexane (2,3-DMH are the major products of respective isomerization of n-hexane, n-heptane and n-octane, besides a small amount of other branched isomers are also produced. The product distribution is comparable to that reported for Pt based other catalysts. The optimal mole ratios of Pt:Al is 1:1 (PGA-2 gives quite good catalytic activity for isomerization of n-alkane. Even through in reusability study, PGA-2 gives better performance than others. We have mainly focused on kinetic study, reaction mechanism behind isomerization and calculated the order of reactions and activation energies of the isomerization reactions in the present work. Keywords: Isomerization, n-alkanes, Catalyst, Reaction mechanism, Kinetics study, Activation energy

Ametryn degradation by aqueous chlorine: Kinetics and reaction influences

International Nuclear Information System (INIS)

Xu Bin; Gao Naiyun; Cheng Hefa; Hu Chenyan; Xia Shengji; Sun Xiaofeng; Wang Xuejiao; Yang Shaogui

2009-01-01

The chemical oxidation of the herbicide ametryn was investigated by aqueous chlorination between pH 4 and 10 at a temperature of 25 deg. C. Ametryn was found to react very rapidly with aqueous chlorine. The reaction kinetics can be well described by a second-order kinetic model. The apparent second-order rate constants are greater than 5 x 10 2 M -1 s -1 under acidic and neutral conditions. The reaction proceeds much more slowly under alkaline conditions. The predominant reactions were found to be the reactions of HOCl with neutral ametryn and the charged ametryn, with rate constants equal to 7.22 x 10 2 and 1.58 x 10 3 M -1 s -1 , respectively. The ametryn degradation rate increases with addition of bromide and decreases with addition of ammonia during the chlorination process. Based on elementary chemical reactions, a kinetic model of ametryn degradation by chlorination in the presence of bromide or ammonia ion was also developed. By employing this model, we estimate that the rate constants for the reactions of HOBr with neutral ametryn and charged ametryn were 9.07 x 10 3 and 3.54 x 10 6 M -1 s -1 , respectively. These values are 10- to 10 3 -fold higher than those of HOCl, suggesting that the presence of bromine species during chlorination could significantly accelerate ametryn degradation.

Kinetics and thermochemistry of the reversible gas phase reaction HONO+NH3->3N-HONO studied by infrared diode laser spectroscopy

DEFF Research Database (Denmark)

Pagsberg, P.; Ratajczak, E.; Sillesen, A.

1994-01-01

The kinetics of the reversible reaction HONO+NH3 reversible H3N-HONO (1) was studied by monitoring trans-HONO relaxation kinetics. The rate of approach towards equilibrium was studied as a function of the ammonia concentration to obtain values of the rate constants for the forward and reverse rea...

Gas-phase thermolysis reaction of formaldehyde diperoxide. Kinetic study and theoretical mechanisms

International Nuclear Information System (INIS)

Jorge, Nelly Lidia; Romero, Jorge Marcelo; Grand, André; Hernández-Laguna, Alfonso

2012-01-01

Highlights: ► Kinetic and mechanism of the gas-phase thermolysis of tetroxane were determined. ► Gas chromatography and computational potential energy surfaces were performed. ► A mechanism in steps looked like the most probable mechanism. ► A spin–orbit coupling appeared at the singlet and triple diradical open structures. ► A non-adiabatic crossing from the singlet to the triplet state occurred. - Abstract: Gas-phase thermolysis reaction of formaldehyde diperoxide (1,2,4,5-tetroxane) was performed in an injection chamber of a gas chromatograph at a range of 463–503 K. The average Arrhenius activation energy and pre-exponential factor were 29.3 ± 0.8 kcal/mol and 5.2 × 10 13 s −1 , respectively. Critical points and reaction paths of the ground singlet and first triplet potential energy surfaces (PES) were calculated, using DFT method at BHANDHLYP/6-311+G ∗∗ level of the theory. Also, G3 calculations were performed on the reactant and products. Reaction by the ground-singlet and first-triplet states turned out to be endothermic and exothermic, respectively. The mechanism in three steps seemed to be the most probable one. An electronically non-adiabatic process appeared, in which a crossing, at an open diradical structure, from the singlet to the triplet state PES occurred, due to a spin–orbit coupling, yielding an exothermic reaction. Theoretical kinetic constant coming from the non- adiabatic transition from the singlet to the triplet state agrees with the experimental values.

Study on the kinetics of gel formation in the radiation crosslinking reaction

International Nuclear Information System (INIS)

Wang Mingjun; Liu Yuming

1988-01-01

From the kinetic equation of gel formation obtained by the authors, the mechanism of gel formation may be interpreted clearly as follows: (1) When the degree of crosslinking q g , the system is sol and the crosslinking reaction is only carried out between the sol molecules. (q g is the gel point). (2) When q=q g , there exists a beginning point where the gel is coexisted with the sol, and the system is still sol, and the crosslinking reaction is still carried out between the sol molecules. (3) When q>q g , the crosslinking reaction exceeds the gel point and the gel is coexisted with the sol. The kinetic equation shows clearly that the transformation from sol into gel is caused by crosslinking reaction of the uncrosslinked chain units between the sol and gel molecules. As a result the sol molecules are transformed into the gel molecules gradually, and the sol fraction is reduced. When the chain units P-barw(s)S(1-s)dq in sol are crosslinked with gel, the sol fraction in the system is reduced ds (where P-barw(s) is a function of the radiation dose and s is sol frection). The degree of crosslinking per unit dose (q 0 ) is a reduced function of dose (R). The equation for calculating its value for every irradiation dose is obtained. After knowing the correlation between P-bar W(s) vs R and q 0 vs R, the distribution of gel and sol in the process of radiation crosslinking can be discussed as well

Kinetics of reactions of aquacobalamin with aspartic and glutamic acids and their amides in water solutions

Science.gov (United States)

Bui, T. T. T.; Sal'nikov, D. S.; Dereven'kov, I. A.; Makarov, S. V.

2017-04-01

The kinetics of aquacobalamin reaction with aspartic and glutamic acids, and with their amides in water solutions, is studied via spectrophotometry. The kinetic and activation parameters of the process are determined. It is shown that the reaction product is cobalamin-amino acid complex. The data are compared to results on the reaction between aquacobalamin and primary amines.

Accurate label-free reaction kinetics determination using initial rate heat measurements

Science.gov (United States)

Ebrahimi, Kourosh Honarmand; Hagedoorn, Peter-Leon; Jacobs, Denise; Hagen, Wilfred R.

2015-01-01

Accurate label-free methods or assays to obtain the initial reaction rates have significant importance in fundamental studies of enzymes and in application-oriented high throughput screening of enzyme activity. Here we introduce a label-free approach for obtaining initial rates of enzyme activity from heat measurements, which we name initial rate calorimetry (IrCal). This approach is based on our new finding that the data recorded by isothermal titration calorimetry for the early stages of a reaction, which have been widely ignored, are correlated to the initial rates. Application of the IrCal approach to various enzymes led to accurate enzyme kinetics parameters as compared to spectroscopic methods and enabled enzyme kinetic studies with natural substrate, e.g. proteases with protein substrates. Because heat is a label-free property of almost all reactions, the IrCal approach holds promise in fundamental studies of various enzymes and in use of calorimetry for high throughput screening of enzyme activity. PMID:26574737

The redox reaction kinetics of Sinai ore for chemical looping combustion applications

International Nuclear Information System (INIS)

Ksepko, Ewelina; Babiński, Piotr; Nalbandian, Lori

2017-01-01

Highlights: • Redox reaction kinetics of Fe-Mn-rich Sinai ore was determined by TGA. • The most suitable model for reduction was D3, while R3 for oxidation. • Activation energies 35.3 and 16.70 kJ/mole were determined for reduction and oxidation. • Repetitive redox reactions favor the formation of spinel phases in Sinai ore. • Multiple redox cycles induce formation of extensive porosity of the particles. - Abstract: The objective of this work was to study the use of Sinai ore, a Fe–Mn-based ore from Egypt, as a low-cost oxygen carrier (OC) in Chemical Looping Combustion (CLC). The Sinai ore was selected because it possesses relatively high amounts of iron and manganese oxides. Furthermore, those oxides have low cost, very favorable environmental and thermodynamic properties for the CLC process. The performance of the Sinai ore as an OC in CLC was compared to that of ilmenite (Norway Tellnes mine), the most extensively studied naturally occurring Fe-based mineral. The kinetics of the reduction and oxidation reactions with the two minerals were studied using a thermogravimetric analyzer (TGA). Experiments were conducted under isothermal conditions, with multiple redox cycles, at temperatures between 750 and 950 °C. For the reduction and oxidation reactions, different concentrations of CH_4 (10–25 vol.%) and O_2 (5–20 vol.%) were applied, respectively. The kinetic parameters, such as the activation energy (E_a), pre-exponential factor (A_0), and reaction order (n), were determined for the redox reactions. Furthermore, models of the redox reactions were selected by means of a model-fitting method. For the Sinai ore, the D3 model (3-dimensional diffusion) was suitable for modeling reduction reaction kinetics. The calculated E_a was 35.3 kJ/mole, and the reaction order was determined to be approximately 0.76. The best fit for the oxidation reaction was obtained for the R3 model (shrinking core). The oxidation (regeneration) reaction E_a was equal to 16

Kinetic investigation of heterogeneous catalytic reactions by means of the kinetic isotope method

Energy Technology Data Exchange (ETDEWEB)

Bauer, F; Dermietzel, J [Akademie der Wissenschaften der DDR, Leipzig. Zentralinstitut fuer Isotopen- und Strahlenforschung

1978-09-01

The application of the kinetic isotope method to heterogeneous catalytic processes is possible for surface compounds by using the steady-state relation. However, the characterization of intermediate products becomes ambiguous if sorption rates are of the same order of magnitude as surface reactions rates. The isotopic exchange reaction renders possible the estimation of sorption rates.

Reaction Mechanism Generator: Automatic construction of chemical kinetic mechanisms

Science.gov (United States)

Gao, Connie W.; Allen, Joshua W.; Green, William H.; West, Richard H.

2016-06-01

Reaction Mechanism Generator (RMG) constructs kinetic models composed of elementary chemical reaction steps using a general understanding of how molecules react. Species thermochemistry is estimated through Benson group additivity and reaction rate coefficients are estimated using a database of known rate rules and reaction templates. At its core, RMG relies on two fundamental data structures: graphs and trees. Graphs are used to represent chemical structures, and trees are used to represent thermodynamic and kinetic data. Models are generated using a rate-based algorithm which excludes species from the model based on reaction fluxes. RMG can generate reaction mechanisms for species involving carbon, hydrogen, oxygen, sulfur, and nitrogen. It also has capabilities for estimating transport and solvation properties, and it automatically computes pressure-dependent rate coefficients and identifies chemically-activated reaction paths. RMG is an object-oriented program written in Python, which provides a stable, robust programming architecture for developing an extensible and modular code base with a large suite of unit tests. Computationally intensive functions are cythonized for speed improvements.

Reaction kinetics of cellulose hydrolysis in subcritical and supercritical water

Science.gov (United States)

Olanrewaju, Kazeem Bode

The uncertainties in the continuous supply of fossil fuels from the crisis-ridden oil-rich region of the world is fast shifting focus on the need to utilize cellulosic biomass and develop more efficient technologies for its conversion to fuels and chemicals. One such technology is the rapid degradation of cellulose in supercritical water without the need for an enzyme or inorganic catalyst such as acid. This project focused on the study of reaction kinetics of cellulose hydrolysis in subcritical and supercritical water. Cellulose reactions at hydrothermal conditions can proceed via the homogeneous route involving dissolution and hydrolysis or the heterogeneous path of surface hydrolysis. The work is divided into three main parts. First, the detailed kinetic analysis of cellulose reactions in micro- and tubular reactors was conducted. Reaction kinetics models were applied, and kinetics parameters at both subcritical and supercritical conditions were evaluated. The second major task was the evaluation of yields of water soluble hydrolysates obtained from the hydrolysis of cellulose and starch in hydrothermal reactors. Lastly, changes in molecular weight distribution due to hydrothermolytic degradation of cellulose were investigated. These changes were also simulated based on different modes of scission, and the pattern generated from simulation was compared with the distribution pattern from experiments. For a better understanding of the reaction kinetics of cellulose in subcritical and supercritical water, a series of reactions was conducted in the microreactor. Hydrolysis of cellulose was performed at subcritical temperatures ranging from 270 to 340 °C (tau = 0.40--0.88 s). For the dissolution of cellulose, the reaction was conducted at supercritical temperatures ranging from 375 to 395 °C (tau = 0.27--0.44 s). The operating pressure for the reactions at both subcritical and supercritical conditions was 5000 psig. The results show that the rate-limiting step in

Hydrolysis reaction of 2,4-dichlorophenoxyacetic acid. A kinetic and computational study

Science.gov (United States)

Romero, Jorge Marcelo; Jorge, Nelly Lidia; Grand, André; Hernández-Laguna, Alfonso

2015-10-01

The degradation of the 2,4-dichlorophenoxyacetic acid in aqueous solution is an hydrolysis reaction. Two products are identified: 2,4-dichlorophenol and glycolic acid. Reaction is investigated as a function of pH and temperature, and it is first-order kinetics and pH-dependent. Reaction is modeled in gas phase, where a proton catalyses the reaction. Critical points of PES are calculated at B3LYP/6-311++G(3df,2p), and aug-cc-pvqz//6-311++G(3df,2p) levels plus ZPE at 6-311++G(3df,2p) level. The activation barrier is 21.2 kcal/mol. Theoretical results agree with the experimental results. A second mechanism related with a Cl2Phsbnd Osbnd CH2sbnd COOH⋯H2O complex is found, but with a rate limiting step of 38.4 kcal/mol.

Role of Re in Pt-Re/TiO2 catalyst for water gas shift reaction: A mechanistic and kinetic study.

NARCIS (Netherlands)

Azzam, K.G.H.; Babych, Igor V.; Seshan, Kulathuiyer; Lefferts, Leonardus

2008-01-01

Transient kinetic studies and in situ FTIR spectroscopy were used to follow the reaction sequences that occur during water gas shift (WGS) reaction over Pt–Re/TiO2 catalyst. Results pointed to contributions of an associative formate route with redox regeneration and two classical redox routes

Reactions driving conformational movements (molecular motors) in gels: conformational and structural chemical kinetics.

Science.gov (United States)

Otero, Toribio F

2017-01-18

In this perspective the empirical kinetics of conducting polymers exchanging anions and solvent during electrochemical reactions to get dense reactive gels is reviewed. The reaction drives conformational movements of the chains (molecular motors), exchange of ions and solvent with the electrolyte and structural (relaxation, swelling, shrinking and compaction) gel changes. Reaction-driven structural changes are identified and quantified from electrochemical responses. The empirical reaction activation energy (E a ), the reaction coefficient (k) and the reaction orders (α and β) change as a function of the conformational energy variation during the reaction. This conformational energy becomes an empirical magnitude. E a , k, α and β include and provide quantitative conformational and structural information. The chemical kinetics becomes structural chemical kinetics (SCK) for reactions driving conformational movements of the reactants. The electrochemically stimulated conformational relaxation model describes empirical results and some results from the literature for biochemical reactions. In parallel the development of an emerging technological world of soft, wet, multifunctional and biomimetic tools and anthropomorphic robots driven by reactions of the constitutive material, as in biological organs, can be now envisaged being theoretically supported by the kinetic model.

Kinetic study of the Diels-Alder reaction of Li⁺@C₆₀ with cyclohexadiene: greatly increased reaction rate by encapsulated Li⁺.

Science.gov (United States)

Ueno, Hiroshi; Kawakami, Hiroki; Nakagawa, Koji; Okada, Hiroshi; Ikuma, Naohiko; Aoyagi, Shinobu; Kokubo, Ken; Matsuo, Yutaka; Oshima, Takumi

2014-08-06

We studied the kinetics of the Diels-Alder reaction of Li(+)-encapsulated [60]fullerene with 1,3-cyclohexadiene and characterized the obtained product, [Li(+)@C60(C6H8)](PF6(-)). Compared with empty C60, Li(+)@C60 reacted 2400-fold faster at 303 K, a rate enhancement that corresponds to lowering the activation energy by 24.2 kJ mol(-1). The enhanced Diels-Alder reaction rate was well explained by DFT calculation at the M06-2X/6-31G(d) level of theory considering the reactant complex with dispersion corrections. The calculated activation energies for empty C60 and Li(+)@C60 (65.2 and 43.6 kJ mol(-1), respectively) agreed fairly well with the experimentally obtained values (67.4 and 44.0 kJ mol(-1), respectively). According to the calculation, the lowering of the transition state energy by Li(+) encapsulation was associated with stabilization of the reactant complex (by 14.1 kJ mol(-1)) and the [4 + 2] product (by 5.9 kJ mol(-1)) through favorable frontier molecular orbital interactions. The encapsulated Li(+) ion catalyzed the Diels-Alder reaction by lowering the LUMO of Li(+)@C60. This is the first detailed report on the kinetics of a Diels-Alder reaction catalyzed by an encapsulated Lewis acid catalyst rather than one coordinated to a heteroatom in the dienophile.

Gas-phase thermolysis reaction of formaldehyde diperoxide. Kinetic study and theoretical mechanisms

Energy Technology Data Exchange (ETDEWEB)

Jorge, Nelly Lidia [Instituto Andaluz de Ciencias de la Tierra, CSIC-Universidad de Granada, Av. Las Palmeras 4, 18100 Armilla, Granada (Spain); Area de Quimica Fisica Facultad de Ciencias Exactas y Naturales y Agrimensura, UNNE, Avda. Libertad 5460, 3400 Corrientes (Argentina); Romero, Jorge Marcelo [Area de Quimica Fisica Facultad de Ciencias Exactas y Naturales y Agrimensura, UNNE, Avda. Libertad 5460, 3400 Corrientes (Argentina); Grand, Andre [INAC, SCIB, Laboratoire ' Lesions des Acides Nucleiques' , UMR CEA-UJF E3, CEA-Grenoble, 17 Rue des Martyrs, 38054 Grenoble cedex 9 (France); Hernandez-Laguna, Alfonso, E-mail: ahlaguna@ugr.es [Instituto Andaluz de Ciencias de la Tierra, CSIC-Universidad de Granada, Av. Las Palmeras 4, 18100 Armilla, Granada (Spain)

2012-01-17

Highlights: Black-Right-Pointing-Pointer Kinetic and mechanism of the gas-phase thermolysis of tetroxane were determined. Black-Right-Pointing-Pointer Gas chromatography and computational potential energy surfaces were performed. Black-Right-Pointing-Pointer A mechanism in steps looked like the most probable mechanism. Black-Right-Pointing-Pointer A spin-orbit coupling appeared at the singlet and triple diradical open structures. Black-Right-Pointing-Pointer A non-adiabatic crossing from the singlet to the triplet state occurred. - Abstract: Gas-phase thermolysis reaction of formaldehyde diperoxide (1,2,4,5-tetroxane) was performed in an injection chamber of a gas chromatograph at a range of 463-503 K. The average Arrhenius activation energy and pre-exponential factor were 29.3 {+-} 0.8 kcal/mol and 5.2 Multiplication-Sign 10{sup 13} s{sup -1}, respectively. Critical points and reaction paths of the ground singlet and first triplet potential energy surfaces (PES) were calculated, using DFT method at BHANDHLYP/6-311+G{sup Asterisk-Operator Asterisk-Operator} level of the theory. Also, G3 calculations were performed on the reactant and products. Reaction by the ground-singlet and first-triplet states turned out to be endothermic and exothermic, respectively. The mechanism in three steps seemed to be the most probable one. An electronically non-adiabatic process appeared, in which a crossing, at an open diradical structure, from the singlet to the triplet state PES occurred, due to a spin-orbit coupling, yielding an exothermic reaction. Theoretical kinetic constant coming from the non- adiabatic transition from the singlet to the triplet state agrees with the experimental values.

Kinetics of the Br2-CH3CHO Photochemical Chain Reaction

Science.gov (United States)

Nicovich, J. M.; Shackelford, C. J.; Wine, P. H.

1997-01-01

Time-resolved resonance fluorescence spectroscopy was employed in conjunction with laser flash photolysis of Br2 to study the kinetics of the two elementary steps in the photochemical chain reaction nBr2 + nCH3CHO + hv yields nCH3CBrO + nHBr. In the temperature range 255-400 K, the rate coefficient for the reaction Br((sup 2)P(sub 3/2)) + CH3CHO yields CH3CO + HBr is given by the Arrhenius expression k(sub 6)(T) = (1.51 +/- 0.20) x 10(exp -11) exp(-(364 +/- 41)/T)cu cm/(molecule.s). At 298 K, the reaction CH3CO + Br2 yields CH3CBrO + Br proceeds at a near gas kinetic rate, k(sub 7)(298 K) = (1.08 +/- 0.38) x 10(exp -10)cu cm/(molecule.s).

Experimental study of the reactions of limonene with OH and OD radicals: kinetics and products.

Science.gov (United States)

Braure, Tristan; Bedjanian, Yuri; Romanias, Manolis N; Morin, Julien; Riffault, Véronique; Tomas, Alexandre; Coddeville, Patrice

2014-10-09

The kinetics of the reactions of limonene with OH and OD radicals has been studied using a low-pressure flow tube reactor coupled with a quadrupole mass spectrometer: OH + C10H16 → products (1), OD + C10H16 → products (2). The rate constants of the title reactions were determined using four different approaches: either monitoring the kinetics of OH (OD) radicals or limonene consumption in excess of limonene or of the radicals, respectively (absolute method), and by the relative rate method using either the reaction OH (OD) + Br2 or OH (OD) + DMDS (dimethyl disulfide) as the reference one and following HOBr (DOBr) formation or DMDS and limonene consumption, respectively. As a result of the absolute and relative measurements, the overall rate coefficients, k1 = (3.0 ± 0.5) × 10(-11) exp((515 ± 50)/T) and k2 = (2.5 ± 0.6) × 10(-11) exp((575 ± 60)/T) cm(3) molecule(-1) s(-1), were determined at a pressure of 1 Torr of helium over the temperature ranges 220-360 and 233-353 K, respectively. k1 was found to be pressure independent over the range 0.5-5 Torr. There are two possible pathways for the reaction between OH (OD) and limonene: addition of the radical to one of the limonene double bonds (reactions 1a and 2a ) and abstraction of a hydrogen atom (reactions 1b and 2b ), resulting in the formation of H2O (HOD). Measurements of the HOD yield as a function of temperature led to the following branching ratio of the H atom abstraction channel: k2b/k2 = (0.07 ± 0.03) × exp((460 ± 140)/T) for T = (253-355) K.

Iteration scheme for implicit calculations of kinetic and equilibrium chemical reactions in fluid dynamics

International Nuclear Information System (INIS)

Ramshaw, J.D.; Chang, C.H.

1995-01-01

An iteration scheme for the implicit treatment of equilibrium chemical reactions in partial equilibrium flow has previously been described. Here we generalize this scheme to kinetic reactions as well as equilibrium reactions. This extends the applicability of the scheme to problems with kinetic reactions that are fast in regions of the flow field but slow in others. The resulting scheme thereby provides a single unified framework for the implicit treatment of an arbitrary number of coupled equilibrium and kinetic reactions in chemically reacting fluid flow. 10 refs., 2 figs

Reaction kinetics for preparation of silica film with Stoeber method

International Nuclear Information System (INIS)

Shang Mengying; Jiang Xiaodong; Liu Miao; Luo Xuan; Tang Yongjian; Cao Linhong

2013-01-01

A new formula was proposed to investigate the relationship between reaction time and tetraethylorthosilicate (TEOS) conversion rate for preparation of silica sol with Stöber method, by studying the reaction kinetics of TEOS hydrolytic process. An appropriate conversion rate was then determined and used to calculate the theoretical optimal reaction time. Meanwhile, silica sols were prepared by sol-gel process using TEOS as precursor and ammonia as catalyst. It was found that the reaction time decreases with an increasing amount of ammonia and water. The values of experimental optimal reaction time were obtained, and agree with the theoretical results (the errors are within 5%), which shows good applicability of our formula. (authors)

Kinetic and Mechanistic Study of the pH-Dependent Activation (Epoxidation) of Prodrug Treosulfan Including the Reaction Inhibition in a Borate Buffer.

Science.gov (United States)

Romański, Michał; Ratajczak, Whitney; Główka, Franciszek

2017-07-01

A prodrug treosulfan (T) undergoes a pH-dependent activation to epoxide derivatives. The process seems to involve an intramolecular Williamson reaction (IWR) but clear kinetic evidence is lacking. Moreover, a cis-diol system present in the T structure is expected to promote complexation with boric acid. As a result, the prodrug epoxidation would be inhibited; however, this phenomenon has not been investigated. In this article, the effect of pH on the kinetics of T conversion to its monoepoxide was studied from a mechanistic point of view. Also, the influence of boric acid on the reaction kinetics was examined. The rate constants observed for the activation of T (k obs ) in acetate, phosphate, and carbonate buffers satisfied the equation logk obs  = -7.48 + 0.96 pH. The reaction was inhibited in the excess of boric acid over T, and the k obs decreased with increasing borate buffer concentration. The experimental results were consistent with the inhibition model that included the formation of a tetrahedral, anionic T-boric acid monoester. To conclude, in nonborate buffers, the T activation to (2S,3S)-1,2-epoxybutane-3,4-diol 4-methanesulfonate follows IWR mechanism. A borate buffer changes the reaction kinetics and complicates kinetic analysis. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Reaction kinetics of bond rotations in graphene

KAUST Repository

Skowron, Stephen T.; Koroteev, Victor O.; Baldoni, Matteo; Lopatin, Sergei; Zurutuza, Amaia; Chuvilin, Andrey; Besley, Elena

2016-01-01

The formation and healing processes of the fundamental topological defect in graphitic materials, the Stone-Wales (SW) defect, are brought into a chemical context by considering the rotation of a carbon-carbon bond as chemical reaction. We investigate the rates and mechanisms of these SW transformations in graphene at the atomic scale using transmission electron microscopy. We develop a statistical atomic kinetics formalism, using direct observations obtained under different conditions to determine key kinetic parameters of the reactions. Based on the obtained statistics we quantify thermally and irradiation induced routes, identifying a thermal process of healing with an activation energy consistent with predicted adatom catalysed mechanisms. We discover exceptionally high rates for irradiation induced SW healing, incompatible with the previously assumed mechanism of direct knock-on damage and indicating the presence of an efficient nonadiabatic coupling healing mechanism involving beam induced electronic excitations of the SW defect.

Reaction kinetics of bond rotations in graphene

KAUST Repository

Skowron, Stephen T.

2016-04-12

The formation and healing processes of the fundamental topological defect in graphitic materials, the Stone-Wales (SW) defect, are brought into a chemical context by considering the rotation of a carbon-carbon bond as chemical reaction. We investigate the rates and mechanisms of these SW transformations in graphene at the atomic scale using transmission electron microscopy. We develop a statistical atomic kinetics formalism, using direct observations obtained under different conditions to determine key kinetic parameters of the reactions. Based on the obtained statistics we quantify thermally and irradiation induced routes, identifying a thermal process of healing with an activation energy consistent with predicted adatom catalysed mechanisms. We discover exceptionally high rates for irradiation induced SW healing, incompatible with the previously assumed mechanism of direct knock-on damage and indicating the presence of an efficient nonadiabatic coupling healing mechanism involving beam induced electronic excitations of the SW defect.

The kinetics of the reduction reaction of plutonium(IV) with N,N-dimethylhydroxylamine

International Nuclear Information System (INIS)

Yanxin Chen; Honbing Tang; Jinping Liu; Hui He

2011-01-01

The kinetics of reduction reactions between N,N-dimethylhydroxylamine (DMHAN) and plutonium(IV) in nitric acid solution have been studied spectrophotometrically. The kinetic equation of the reaction is determined to be -d[Pu(IV)]/dt = k 0 [Pu(IV)][DMHAN] 1.18 /[H + ] 2.22 at the beginning, where, the rate constant of the reaction (k 0 ) is 10.5 ± 1.8(mol/L) 1.04 s -1 at 14.5 deg C. By regressing of the time-concentration curve of the reaction, The complete rate equation is calculated as -d[Pu(IV)] / dt = k[Pu(IV)] 2 [DMHAN] 1.18 /[H + ] 2.22 / 8.12[Pu(III)]+95.9[Pu(IV)] with the reaction constant k about 1,000(mol/L) 1.04 s -1 at 14.5 deg C and an ionic strength (μ) of 4.0 mol/L. (author)

Deviation from the kinetic law of mass action for reactions induced by binary encounters in liquid solutions

International Nuclear Information System (INIS)

Doktorov, Alexander B; Kipriyanov, Alexey A

2007-01-01

In considering the irreversible chemical reaction A+B→ C+B in liquid solutions two many-particle approaches to the derivation of binary non-Markovian kinetic equations are compared: simple superposition decoupling and a method of extracting 'pair' channels from three-particle correlation evolution. It is shown that both methods provide an almost identical description of this reaction. However, in studies of reversible reactions in liquid solutions only the channel extraction method gives a correct physically clear description of the reaction though it consists of a sequence of steps: the development of integral encounter theory (IET), effective pairs approximation (EPA), modified encounter theory (MET), and the final regular form (RF) of kinetic equations. It is shown that the rate equations often encountered in the literature correspond to the independence of transient channels of 'scattering' in the bimolecular reversible reaction (A+B -B), while the independent transient channel of 'decay' in the reversible reactionA+B -C is defined solely by time integral convolution. In the general case transient channels in non-Markovian theory are not independent, and their interference manifests itself as a non-Markovian inhomogeneous source in binary non-Markovian kinetic equations in regular form. Based on the derived equations new universal kinetics (independent of models) of chemical equilibrium attainment have been obtained. It is shown that these kinetics can differ essentially from the kinetics corresponding to the kinetic law of mass action of formal chemical kinetics

Ion-neutral gas reactions in a collision/reaction cell in inductively coupled plasma mass spectrometry: Correlation of ion signal decrease to kinetic rate constants

Energy Technology Data Exchange (ETDEWEB)

Gray, Patrick J. [Trace Element Research Laboratory, School of Earth Sciences, The Ohio State University, 125 S. Oval Mall, Columbus, OH 43210 (United States); Department of Chemistry, The Ohio State University, 120 18th Avenue, Columbus, OH 43210 (United States); Olesik, John W., E-mail: olesik.2@osu.edu [Trace Element Research Laboratory, School of Earth Sciences, The Ohio State University, 125 S. Oval Mall, Columbus, OH 43210 (United States)

2015-03-01

Reaction gas flow rate dependent Ar{sub 2}{sup +} and Ar{sup +} signals are correlated to fundamental kinetic rate coefficients. A simple calculation, assuming that gas exits the reaction cell due only to effusion, is described to estimate the gas pressure in the reaction cell. The value of the product of the kinetic rate constant and the ion residence time in the reaction cell can be determined from experimental measurement of the decrease in an ion signal as a function of reaction gas flow rate. New kinetic rate constants are determined for the reaction of CH{sub 3}F with Ar{sup +} and Ar{sub 2}{sup +}. - Highlights: • How to determine pressure and the product of the kinetic rate constant times the ion residence time in reaction cell • Relate measured ICP-DRC-MS signals versus gas flow rate to kinetic rate constants measured previously using SIFT-MS • Describe how to determine previously unmeasured kinetic rate constants using ICP-DRC-MS.

Complex Reaction Kinetics in Chemistry: A Unified Picture Suggested by Mechanics in Physics

Directory of Open Access Journals (Sweden)

Elena Agliari

2018-01-01

Full Text Available Complex biochemical pathways can be reduced to chains of elementary reactions, which can be described in terms of chemical kinetics. Among the elementary reactions so far extensively investigated, we recall the Michaelis-Menten and the Hill positive-cooperative kinetics, which apply to molecular binding and are characterized by the absence and the presence, respectively, of cooperative interactions between binding sites. However, there is evidence of reactions displaying a more complex pattern: these follow the positive-cooperative scenario at small substrate concentration, yet negative-cooperative effects emerge as the substrate concentration is increased. Here, we analyze the formal analogy between the mathematical backbone of (classical reaction kinetics in Chemistry and that of (classical mechanics in Physics. We first show that standard cooperative kinetics can be framed in terms of classical mechanics, where the emerging phenomenology can be obtained by applying the principle of least action of classical mechanics. Further, since the saturation function plays in Chemistry the same role played by velocity in Physics, we show that a relativistic scaffold naturally accounts for the kinetics of the above-mentioned complex reactions. The proposed formalism yields to a unique, consistent picture for cooperative-like reactions and to a stronger mathematical control.

Unravelling the Maillard reaction network by multiresponse kinetic modelling

NARCIS (Netherlands)

Martins, S.I.F.S.

2003-01-01

The Maillard reaction is an important reaction in food industry. It is responsible for the formation of colour and aroma, as well as toxic compounds as the recent discovered acrylamide. The knowledge of kinetic parameters, such as rate constants and activation energy, is necessary to predict its

Kinetic modeling and fitting software for interconnected reaction schemes: VisKin.

Science.gov (United States)

Zhang, Xuan; Andrews, Jared N; Pedersen, Steen E

2007-02-15

Reaction kinetics for complex, highly interconnected kinetic schemes are modeled using analytical solutions to a system of ordinary differential equations. The algorithm employs standard linear algebra methods that are implemented using MatLab functions in a Visual Basic interface. A graphical user interface for simple entry of reaction schemes facilitates comparison of a variety of reaction schemes. To ensure microscopic balance, graph theory algorithms are used to determine violations of thermodynamic cycle constraints. Analytical solutions based on linear differential equations result in fast comparisons of first order kinetic rates and amplitudes as a function of changing ligand concentrations. For analysis of higher order kinetics, we also implemented a solution using numerical integration. To determine rate constants from experimental data, fitting algorithms that adjust rate constants to fit the model to imported data were implemented using the Levenberg-Marquardt algorithm or using Broyden-Fletcher-Goldfarb-Shanno methods. We have included the ability to carry out global fitting of data sets obtained at varying ligand concentrations. These tools are combined in a single package, which we have dubbed VisKin, to guide and analyze kinetic experiments. The software is available online for use on PCs.

Thermo-Kinetic Investigation of Comparative Ligand Effect on Cysteine Iron Redox Reaction

Directory of Open Access Journals (Sweden)

Masood Ahmad Rizvi

2015-03-01

Full Text Available Transition metal ions in their free state bring unwanted biological oxidations generating oxidative stress. The ligand modulated redox potential can be indispensable in prevention of such oxidative stress by blocking the redundant bio-redox reactions. In this study we investigated the comparative ligand effect on the thermo-kinetic aspects of biologically important cysteine iron (III redox reaction using spectrophotometric and potentiometric methods. The results were corroborated with the complexation effect on redox potential of iron(III-iron(II redox couple. The selected ligands were found to increase the rate of cysteine iron (III redox reaction in proportion to their stability of iron (II complex (EDTA < terpy < bipy < phen. A kinetic profile and the catalytic role of copper (II ions by means of redox shuttle mechanism for the cysteine iron (III redox reaction in presence of 1,10-phenanthroline (phen ligand is also reported.

Kinetics and optimization on discoloration of dyeing wastewater by schorl-catalyzed fenton-like reaction

Directory of Open Access Journals (Sweden)

Xu Huan-Yan

2014-01-01

Full Text Available Kinetics and optimization on the discoloration of an active commercial dye, Argazol Blue BFBR (ABB by heterogeneous Fenton-like reaction catalyzed by natural schorl were investigated in this study. Kinetic investigations revealed that the first-order kinetic model was more favorable to describe the discoloration of ABB at different reaction conditions than the second-order and Behnajady-Modirshahla-Ghanbery models. The relationship between the reaction rate constant k and reaction temperature T followed the Arrhenius equation, with the apparent activation energy Ea of 51.31kJ•mol-1. The central composite design under the response surface methodology was employed for the experimental design and optimization of the ABB discoloration process. The significance of a second order polynomial model for predicting the optimal values of ABB discoloration was evaluated by the analysis of variance and 3D response surface plots for the interactions between two variables were constructed. Then, the optimum conditions were determined.

Full-dimensional analytical potential energy surface describing the gas-phase Cl + C2H6 reaction and kinetics study of rate constants and kinetic isotope effects.

Science.gov (United States)

Rangel, Cipriano; Espinosa-Garcia, Joaquin

2018-02-07

Within the Born-Oppenheimer approximation a full-dimensional analytical potential energy surface, PES-2017, was developed for the gas-phase hydrogen abstraction reaction between the chlorine atom and ethane, which is a nine body system. This surface presents a valence-bond/molecular mechanics functional form dependent on 60 parameters and is fitted to high-level ab initio calculations. This reaction presents little exothermicity, -2.30 kcal mol -1 , with a low height barrier, 2.44 kcal mol -1 , and intermediate complexes in the entrance and exit channels. We found that the energetic description was strongly dependent on the ab initio level used and it presented a very flat topology in the entrance channel, which represents a theoretical challenge in the fitting process. In general, PES-2017 reproduces the ab initio information used as input, which is merely a test of self-consistency. As a first test of the quality of the PES-2017, a theoretical kinetics study was performed in the temperature range 200-1400 K using two approaches, i.e. the variational transition-state theory and quasi-classical trajectory calculations, with spin-orbit effects. The rate constants show reasonable agreement with experiments in the whole temperature range, with the largest differences at the lowest temperatures, and this behaviour agrees with previous theoretical studies, thus indicating the inherent difficulties in the theoretical simulation of the kinetics of the title reaction. Different sources of error were analysed, such as the limitations of the PES and theoretical methods, recrossing effects, and the tunnelling effect, which is negligible in this reaction, and the manner in which the spin-orbit effects were included in this non-relativistic study. We found that the variation of spin-orbit coupling along the reaction path, and the influence of the reactivity of the excited Cl( 2 P 1/2 ) state, have relative importance, but do not explain the whole discrepancy. Finally, the

A kinetic model for the glucose/glycine Maillard reaction pathways

NARCIS (Netherlands)

Martins, S.I.F.S.; Boekel, van M.A.J.S.

2005-01-01

A comprehensive kinetic model for the glucose/glycine Maillard reaction is proposed based on an approach called multiresponse kinetic modelling. Special attention was paid to reactants, intermediates and end products: -fructose, N-(1-deoxy--fructos-1-yl)-glycine (DFG), 1-deoxy-2,3-hexodiulose and

Diagnostic Appraisal of Grade 12 Students' Understanding of Reaction Kinetics

Science.gov (United States)

Yan, Yaw Kai; Subramaniam, R.

2016-01-01

The study explored grade 12 students' understanding of reaction kinetics, a topic which has not been extensively explored in the chemistry education literature at this level. A 3-tier diagnostic instrument with 11 questions was developed--this format is of very recent origin and has been the subject of only a handful of studies. The findings…

Kinetic and thermodynamic study of the reaction catalyzed by glucose-6-phosphate dehydrogenase with nicotinamide adenine dinucleotide

International Nuclear Information System (INIS)

Martin del Campo, Julia S.; Patino, Rodrigo

2011-01-01

Research highlights: → The reaction catalyzed by one enzyme of the pentose phosphate pathway was studied. → A spectrophotometric method is proposed for kinetic and thermodynamic analysis. → The pH and the temperature influences are reported on physical chemical properties. → Relative concentrations of substrates are also important in the catalytic process. - Abstract: The enzyme glucose-6-phosphate dehydrogenase (G6PD, EC 1.1.1.49) from Leuconostoc mesenteroides has a dual coenzyme specificity with oxidized nicotinamide adenine dinucleotide (NAD ox ) and oxidized nicotinamide adenine dinucleotide phosphate as electron acceptors. The G6PD coenzyme selection is determined by the metabolic cellular prevailing conditions. In this study a kinetic and thermodynamic analysis is presented for the reaction catalyzed by G6PD from L. mesenteroides with NAD ox as coenzyme in phosphate buffer. For this work, an in situ spectrophotometric technique was employed based on the detection of one product of the reaction. Substrate and coenzyme concentrations as well as temperature and pH effects were evaluated. The apparent equilibrium constant, the Michaelis constant, and the turnover number were determined as a function of each experimental condition. The standard transformed Gibbs energy of reaction was determined from equilibrium constants at different initial conditions. For the product 6-phospho-D-glucono-1,5-lactone, a value of the standard Gibbs energy of formation is proposed, Δ f G o = -1784 ± 5 kJ mol -1 .

Kinetic and thermodynamic study of the reaction catalyzed by glucose-6-phosphate dehydrogenase with nicotinamide adenine dinucleotide

Energy Technology Data Exchange (ETDEWEB)

Martin del Campo, Julia S. [Departamento de Fisica Aplicada, Centro de Investigacion y de Estudios Avanzados - Unidad Merida, Carretera antigua a Progreso Km. 6, A.P. 73 Cordemex, 97310, Merida, Yucatan (Mexico); Patino, Rodrigo, E-mail: rtarkus@mda.cinvestav.mx [Departamento de Fisica Aplicada, Centro de Investigacion y de Estudios Avanzados - Unidad Merida, Carretera antigua a Progreso Km. 6, A.P. 73 Cordemex, 97310, Merida, Yucatan (Mexico)

2011-04-20

Research highlights: {yields} The reaction catalyzed by one enzyme of the pentose phosphate pathway was studied. {yields} A spectrophotometric method is proposed for kinetic and thermodynamic analysis. {yields} The pH and the temperature influences are reported on physical chemical properties. {yields} Relative concentrations of substrates are also important in the catalytic process. - Abstract: The enzyme glucose-6-phosphate dehydrogenase (G6PD, EC 1.1.1.49) from Leuconostoc mesenteroides has a dual coenzyme specificity with oxidized nicotinamide adenine dinucleotide (NAD{sub ox}) and oxidized nicotinamide adenine dinucleotide phosphate as electron acceptors. The G6PD coenzyme selection is determined by the metabolic cellular prevailing conditions. In this study a kinetic and thermodynamic analysis is presented for the reaction catalyzed by G6PD from L. mesenteroides with NAD{sub ox} as coenzyme in phosphate buffer. For this work, an in situ spectrophotometric technique was employed based on the detection of one product of the reaction. Substrate and coenzyme concentrations as well as temperature and pH effects were evaluated. The apparent equilibrium constant, the Michaelis constant, and the turnover number were determined as a function of each experimental condition. The standard transformed Gibbs energy of reaction was determined from equilibrium constants at different initial conditions. For the product 6-phospho-D-glucono-1,5-lactone, a value of the standard Gibbs energy of formation is proposed, {Delta}{sub f}G{sup o} = -1784 {+-} 5 kJ mol{sup -1}.

Energetics and kinetics of ferrocyanide and nitrate/nitrite reactions

International Nuclear Information System (INIS)

Scheele, R.D.; Burger, L.L.; Sell, R.L.

1994-01-01

During the 1950's, radiocesium scavenging at the Hanford site resulted in radioactive waste sludges containing ferrocyanide, nitrate, and nitrite. These waters are a concern since certain mixtures of ferrocyanide and nitrate and/or nitrite are known to explode when heated. The authors have used differential scanning calorimetry, thermogravimetric analysis, isothermal calorimetry and gravimetry, and accelerating rate calorimetry to measure the thermal behavior, the reaction enthalpies, and selected kinetic parameters for reactions between sodium nickel ferrocyanide, the suspected ferrocyanide form in Hanford wastes, and nitrate and/or nitrite. These studies indicate that the oxidation proceeds via multiple steps, the initial reaction begins near 200 degrees C, the initial step has a high activation energy (>200 kJ/mole-K), succeeding reaction steps have activation energies ranging from 90 to 160 kJ/mole-K, and that the oxidation yields about 50% of the theoretical heat of reaction for the most energetic reaction

Kinetics and mechanisms of reactions involving small aromatic reactive intermediates

Energy Technology Data Exchange (ETDEWEB)

Lin, M.C. [Emory Univ., Atlanta, GA (United States)

1993-12-01

Small aromatic radicals such as C{sub 6}H{sub 5}, C{sub 6}H{sub 5}O and C{sub 6}H{sub 4} are key prototype species of their homologs. C{sub 6}H{sub 5} and its oxidation product, C{sub 6}H{sub 5}O are believed to be important intermediates which play a pivotal role in hydrocarbon combustion, particularly with regard to soot formation. Despite their fundamental importance, experimental data on the reaction mechanisms and reactivities of these species are very limited. For C{sub 6}H{sub 5}, most kinetic data except its reactions with NO and NO{sub 2}, were obtained by relative rate measurements. For C{sub 6}H{sub 5}O, the authors have earlier measured its fragmentation reaction producing C{sub 5}H{sub 5} + CO in shock waves. For C{sub 6}H{sub 4}, the only rate constant measured in the gas phase is its recombination rate at room temperature. The authors have proposed to investigate systematically the kinetics and mechanisms of this important class of molecules using two parallel laser diagnostic techniques--laser resonance absorption (LRA) and resonance enhanced multiphoton ionization mass spectrometry (REMPI/MS). In the past two years, study has been focused on the development of a new multipass adsorption technique--the {open_quotes}cavity-ring-down{close_quotes} technique for kinetic applications. The preliminary results of this study appear to be quite good and the sensitivity of the technique is at least comparable to that of the laser-induced fluorescence method.

Determining Li+-Coupled Redox Targeting Reaction Kinetics of Battery Materials with Scanning Electrochemical Microscopy.

Science.gov (United States)

Yan, Ruiting; Ghilane, Jalal; Phuah, Kia Chai; Pham Truong, Thuan Nguyen; Adams, Stefan; Randriamahazaka, Hyacinthe; Wang, Qing

2018-02-01

The redox targeting reaction of Li + -storage materials with redox mediators is the key process in redox flow lithium batteries, a promising technology for next-generation large-scale energy storage. The kinetics of the Li + -coupled heterogeneous charge transfer between the energy storage material and redox mediator dictates the performance of the device, while as a new type of charge transfer process it has been rarely studied. Here, scanning electrochemical microscopy (SECM) was employed for the first time to determine the interfacial charge transfer kinetics of LiFePO 4 /FePO 4 upon delithiation and lithiation by a pair of redox shuttle molecules FcBr 2 + and Fc. The effective rate constant k eff was determined to be around 3.70-6.57 × 10 -3 cm/s for the two-way pseudo-first-order reactions, which feature a linear dependence on the composition of LiFePO 4 , validating the kinetic process of interfacial charge transfer rather than bulk solid diffusion. In addition, in conjunction with chronoamperometry measurement, the SECM study disproves the conventional "shrinking-core" model for the delithiation of LiFePO 4 and presents an intriguing way of probing the phase boundary propagations induced by interfacial redox reactions. This study demonstrates a reliable method for the kinetics of redox targeting reactions, and the results provide useful guidance for the optimization of redox targeting systems for large-scale energy storage.

Biochemical toxicology studies of methomyl and its kinetic reaction with cholinesterase in rats

International Nuclear Information System (INIS)

Tawfik, S.M.; Abdel-Hamid, F.M.

2001-01-01

The effect of the pesticide methomyl on acetylcholinesterase activities in brain and blood of male rats in vivo and the kinetics involved in their reaction in vitro were studied. Also, its effect on peroxidase action of catalase in vivo was studied using 14C - formate. The results showed that methomyl is a competitive inhibitor for acetylcholinesterase and the concentration levels that caused 50% inhibition of the enzyme activity were 2.1 x 10-2 M and 1.9 x 10-4 for brain and blood- Ache, respectively. The inhibition of acetylcholinesterase activity decreased to 67.5 % at the time of appearance of toxicity symptoms. The radioactivity eliminated in both the expired air and in urine was reduced

Kinetics of transuranium element oxidation-reduction reactions in solution

International Nuclear Information System (INIS)

Gourisse, D.

1966-09-01

A review of the kinetics of U, Np, Pu, Am oxidation-reduction reactions is proposed. The relations between the different activation thermodynamic functions (compensatory effect, formal entropy of the activated complex, magnitude of reactions velocities) are considered. The effects of acidity, ionic strength deuterium and mixed solvents polarity on reactions rates are described. The effect of different anions on reactions rates are explained by variations of the reaction standard free energy and variations of the activation free energy (coulombic interactions) resulting from the complexation of dissolved species by these anions. (author) [fr

Extension of a Kinetic-Theory Approach for Computing Chemical-Reaction Rates to Reactions with Charged Particles

Science.gov (United States)

Liechty, Derek S.; Lewis, Mark J.

2010-01-01

Recently introduced molecular-level chemistry models that predict equilibrium and nonequilibrium reaction rates using only kinetic theory and fundamental molecular properties (i.e., no macroscopic reaction rate information) are extended to include reactions involving charged particles and electronic energy levels. The proposed extensions include ionization reactions, exothermic associative ionization reactions, endothermic and exothermic charge exchange reactions, and other exchange reactions involving ionized species. The extensions are shown to agree favorably with the measured Arrhenius rates for near-equilibrium conditions.

Studies of ruthenium complexes, 8. Kinetic studies of the thermal substitution reaction of hexaammine and cis--dihalogenotetraammineruthenium(III) complexes in the solid state

Energy Technology Data Exchange (ETDEWEB)

Ohyoshi, A; Hiraki, S; Odate, T; Kohata, S; Oda, J [Kumamoto Univ. (Japan). Faculty of Engineering

1975-01-01

The kinetics of the thermal substitution reaction of hexaamineruthenium (III) halides and cis-dihalogenotetraamineruthenium (III) halides have been studied in the solid state. The reaction rates and kinetic parameters were determined for these two reactions; (Ru(NH/sub 3/)/sub 6/)X/sub 3/..-->..(RuX(NH/sub 3/)/sub 5/)X/sub 2/+NH/sub 3/, (X=Br, I) and cis - (RuX/sub 2/(NH/sub 3/)/sub 4/)X..-->..(RuX/sub 3/(NH/sub 3/)/sub 3/)+NH/sub 3/, (X=Cl, Br). The values of the rate constant, the activation energy, and the activation entropy were 2.10x10/sup -5/ s/sup -1/ (at 161/sup 0/C), 23.2 kcal mol/sup -1/, and -29.3 e.u. for the hexaamine bromide, and 2.92x10/sup -5/ s/sup -1/ (at 162/sup 0/C), 31.3 kcal mol/sup -1/, and -10.1 e.u. for the cis-dibromotetraamine bromide. The Ssub(N)2 mechanism is more probable for the former reaction, while the Ssub(N)1 mechanism is more probable for the latter reaction.

Explaining the atypical reaction profiles of heme enzymes with a novel mechanistic hypothesis and kinetic treatment.

Directory of Open Access Journals (Sweden)

Kelath Murali Manoj

Full Text Available Many heme enzymes show remarkable versatility and atypical kinetics. The fungal extracellular enzyme chloroperoxidase (CPO characterizes a variety of one and two electron redox reactions in the presence of hydroperoxides. A structural counterpart, found in mammalian microsomal cytochrome P450 (CYP, uses molecular oxygen plus NADPH for the oxidative metabolism (predominantly hydroxylation of substrate in conjunction with a redox partner enzyme, cytochrome P450 reductase. In this study, we employ the two above-mentioned heme-thiolate proteins to probe the reaction kinetics and mechanism of heme enzymes. Hitherto, a substrate inhibition model based upon non-productive binding of substrate (two-site model was used to account for the inhibition of reaction at higher substrate concentrations for the CYP reaction systems. Herein, the observation of substrate inhibition is shown for both peroxide and final substrate in CPO catalyzed peroxidations. Further, analogy is drawn in the "steady state kinetics" of CPO and CYP reaction systems. New experimental observations and analyses indicate that a scheme of competing reactions (involving primary product with enzyme or other reaction components/intermediates is relevant in such complex reaction mixtures. The presence of non-selective reactive intermediate(s affords alternate reaction routes at various substrate/product concentrations, thereby leading to a lowered detectable concentration of "the product of interest" in the reaction milieu. Occam's razor favors the new hypothesis. With the new hypothesis as foundation, a new biphasic treatment to analyze the kinetics is put forth. We also introduce a key concept of "substrate concentration at maximum observed rate". The new treatment affords a more acceptable fit for observable experimental kinetic data of heme redox enzymes.

Bacillus anthracis o-succinylbenzoyl-CoA synthetase: reaction kinetics and a novel inhibitor mimicking its reaction intermediate.

Science.gov (United States)

Tian, Yang; Suk, Dae-Hwan; Cai, Feng; Crich, David; Mesecar, Andrew D

2008-11-25

o-Succinylbenzoyl-CoA (OSB-CoA) synthetase (EC 6.2.1.26) catalyzes the ATP-dependent condensation of o-succinylbenzoate (OSB) and CoA to form OSB-CoA, the fourth step of the menaquinone biosynthetic pathway in Bacillus anthracis. Gene knockout studies have highlighted this enzyme as a potential target for the discovery of new antibiotics. Here we report the first studies on the kinetic mechanism of B. anthracis OSB-CoA synthetase, classifying it as an ordered bi uni uni bi ping-pong mechanism. Through a series of pre-steady-state and steady-state kinetic studies in conjunction with direct binding studies, it is demonstrated that CoA, the last substrate to bind, strongly activates the first half-reaction after the first round of turnover. The activation of the first half-reaction is most likely achieved by CoA stabilizing conformations of the enzyme in the "F" form, which slowly isomerize back to the E form. Thus, the kinetic mechanism of OSB-CoA synthetase may be more accurately described as an ordered bi uni uni bi iso ping-pong mechanism. The substrate specificity of OSB-CoA synthetase was probed using a series of OSB analogues with alterations in the carboxylate groups. OSB-CoA shows a strong preference for OSB over all of the analogues tested as none were active except 4-[2-(trifluoromethyl)phenyl]-4-oxobutyric acid which exhibited a 100-fold decrease in k(cat)/K(m). On the basis of an understanding of OSB-CoA synthetase's kinetic mechanism and substrate specificity, a reaction intermediate analogue of OSB-AMP, 5'-O-{N-[2-(trifluoromethyl)phenyl]-4-oxobutyl}adenosine sulfonamide (TFMP-butyl-AMS), was designed and synthesized. This inhibitor was found to be an uncompetitive inhibitor to CoA and a mixed-type inhibitor to ATP and OSB with low micromolar inhibition constants. Collectively, these results should serve as an important forerunner to more detailed and extensive inhibitor design studies aimed at developing lead compounds against the OSB-CoA synthetase

Laboratory Studies of Stratospheric Bromine Chemistry: Kinetics of the Reactions of Bromine Monoxide with Nitrogen Dioxide and Atomic Oxygen.

Science.gov (United States)

Thorn, Robert Peyton, Jr.

A laser flash photolysis - long path absorption technique has been employed to study the kinetics of the reaction rm BrO + NO_2 + M{k _{16}atopto} products as a function of temperature (248-346 K), pressure (16 -800 Torr), and buffer gas identity (rm N _2,CF_4). 351 nm photolysis of rm NO_2/Br_2/N_2 mixtures generated BrO. The BrO decay in the presence of excess NO_2 was followed by UV absorption at 338.3 nm. The reaction is in the falloff regime between third and second order over the entire range of conditions investigated. This is the first study where temperature dependent measurements of k_{16} (P,T) have been reported at pressures greater than 12 Torr; hence, these results help constrain choices of k_{16}(P,T) for use in modeling stratospheric BrO_{rm x} chemistry. The kinetics of the important stratospheric reaction rm BrO+O(^3P)_sp{to }{k_{14}}Br+O_2 in N_2 buffer gas have been studied as a function of temperature (233-328 K) and pressure (25 -150 Torr) using a novel dual laser flash photolysis/long path absorption/resonance fluorescence technique. 248 nm pulsed laser photolysis of rm Br_2/O _3/N_2 mixtures produces O atoms in excess over Br_2. After a delay sufficient for BrO to be generated, a 532 nm laser pulse photolyses a small fraction of the O_3 to generate O(^3P). The decay of O(^3P) in the presence of an excess, known concentration of BrO, as determined by UV absorption at 338.3 nm and by numerical simulation, is then followed by time-resolved atomic resonance fluorescence spectroscopy. The experimental results have shown the reaction kinetics to be independent of pressure, to increase with decreasing temperature, and to be faster than suggested by the only previous (indirect) measurement. The resulting Anhenius expression for k_{14}(T) is given below.rm k_{14 }(T) = 1.64times 10^{-11} exp (263/T) cm^3 molecule ^{-1} s^{-1} The absolute accuracy of k_{14 }(T) at any temperature within the range studied is estimated to be +/-25%. Possible kinetic

Using a Multi-Tier Diagnostic Test to Explore the Nature of Students' Alternative Conceptions on Reaction Kinetics

Science.gov (United States)

Yan, Yaw Kai; Subramaniam, R.

2018-01-01

This study focused on grade 12 students' understanding of reaction kinetics. A 4-tier diagnostic instrument was developed for this purpose and administered to 137 students in the main study. Findings showed that reaction kinetics is a difficult topic for these students, with a total of 25 alternative conceptions (ACs) being uncovered. Except for…

Kinetics of elementary atom and radical reactions: Progress report

International Nuclear Information System (INIS)

Gordon, R.J.

1986-01-01

Our research program is concerned with the kinetics of elementary gas phase reactions and energy transfer involving polyatomic molecules. We report here on three ongoing projects: The reaction of oxygen atoms with hydrogen molecules, the electronic relaxation of NH radicals, and the vibrational relaxation of highly excited SF 6 molecules. 10 refs., 5 figs

Heterogeneous reaction mechanisms and kinetics relevant to the CVD of semiconductor materials

Energy Technology Data Exchange (ETDEWEB)

Creighton, J.R.; Coltrin, M.E.

1994-03-01

This report documents the state of the art in experimental and theoretical techniques for determining reaction mechanisms and chemical kinetics of heterogeneous reactions relevant to the chemical vapor deposition of semiconductor materials. It summarizes the most common ultra-high vacuum experimental techniques that are used and the types of rate information available from each. Several case studies of specific chemical systems relevant to the microelectronics industry are described. Theoretical methods for calculating heterogeneous reaction rate constants are also summarized.

Photocatalytic Water-Splitting Reaction from Catalytic and Kinetic Perspectives

KAUST Repository

Hisatomi, Takashi

2014-10-16

Abstract: Some particulate semiconductors loaded with nanoparticulate catalysts exhibit photocatalytic activity for the water-splitting reaction. The photocatalysis is distinct from the thermal catalysis because photocatalysis involves photophysical processes in particulate semiconductors. This review article presents a brief introduction to photocatalysis, followed by kinetic aspects of the photocatalytic water-splitting reaction.Graphical Abstract: [Figure not available: see fulltext.

Mixtures of rubber tyre and plastic wastes pyrolysis: A kinetic study

International Nuclear Information System (INIS)

Miranda, Miguel; Cabrita, I.; Pinto, Filomena; Gulyurtlu, I.

2013-01-01

The study performed aimed at analysing possible routes for pyrolysis reaction mechanisms of polymeric materials namely RT (rubber tyre) and plastic wastes (PE (polyethylene), PP (polypropylene) and PS (polystyrene)). Consequently, and seeking sustainable transformation of waste streams into valuable chemicals and renewable liquid fuels, mixture of 30% RT, 20% PE, 30% PP and 20% PS was subjected to pyrolysis. Different kinetic models were studied using experimental data. None of the mechanisms found in literature led to a numerical adjustment and different pathways were investigated. Kinetic studies were performed aiming to evaluate direct conversions into new solid, liquid and gaseous products and if parallel reactions and/or reversible elementary steps should be included. Experiments were performed in batch system at different temperatures and reaction times. Kinetic models were evaluated and reaction pathways were proposed. Models reasonably fit experimental data, allow explaining wastes thermal degradation. Kinetic parameters were estimated for all temperatures and dependence of Ea and pre-exponential factor on temperature was evaluated. The rate constant of some reactions exhibited nonlinear temperature dependence on the logarithmic form of Arrhenius law. This fact strongly suggests that temperature has a significant effect on reaction mechanism of pyrolysis of mixtures of rubber tyre and plastic wastes. - Highlights: • Kinetic study of rubber tyre (RT) and different plastic wastes (PE, PP and PS) was performed in batch reactor. • Definition of possible pathways taken into account for the formation of final products. • Kinetic parameters were estimated. • The effect of reaction temperature and reaction time on liquid composition was performed

Kinetics of heterogeneous catalytic reactions

CERN Document Server

Boudart, Michel

2014-01-01

This book is a critical account of the principles of the kinetics of heterogeneous catalytic reactions in the light of recent developments in surface science and catalysis science. Originally published in 1984. The Princeton Legacy Library uses the latest print-on-demand technology to again make available previously out-of-print books from the distinguished backlist of Princeton University Press. These paperback editions preserve the original texts of these important books while presenting them in durable paperback editions. The goal of the Princeton Legacy Library is to vastly increase acc

Non-equilibrium reaction rates in chemical kinetic equations

Science.gov (United States)

Gorbachev, Yuriy

2018-05-01

Within the recently proposed asymptotic method for solving the Boltzmann equation for chemically reacting gas mixture, the chemical kinetic equations has been derived. Corresponding one-temperature non-equilibrium reaction rates are expressed in terms of specific heat capacities of the species participate in the chemical reactions, bracket integrals connected with the internal energy transfer in inelastic non-reactive collisions and energy transfer coefficients. Reactions of dissociation/recombination of homonuclear and heteronuclear diatomic molecules are considered. It is shown that all reaction rates are the complex functions of the species densities, similarly to the unimolecular reaction rates. For determining the rate coefficients it is recommended to tabulate corresponding bracket integrals, additionally to the equilibrium rate constants. Correlation of the obtained results with the irreversible thermodynamics is established.

HTP kinetics studies on isolated elementary combustion reactions over wide temperature ranges

Energy Technology Data Exchange (ETDEWEB)

Fontijn, A.; Adusei, G.Y.; Hranisavlevic, J.; Bajaj, P.N. [Rensselaer Polytechnic Institute, Troy, NY (United States)

1993-12-01

The goals of this project are to provide accurate data on the temperature dependence of the kinetics of elementary combustion reactions, (i) for use by combustion modelers, and (ii) to gain a better fundamental understanding of, and hence predictive ability for, the chemistry involved. Experimental measurements are made mainly by using the pseudo-static HTP (high-temperature photochemistry) technique. While continuing rate coefficient measurements, further aspects of kinetics research are being explored. Thus, starting from the data obtained, a method for predicting the temperature dependence of rate coefficients of oxygen-atom olefin experiment and confirms the underlying mechanistic assumptions. Mechanistic information of another sort, i.e. by product analysis, has recently become accessible with the inauguration of our heated flow tube mass spectrometer facility; early results are reported here. HTP experiments designed to lead to measurements of product channels by resonance fluorescence have started.

Kinetics of the reaction between H· and superheated water probed with muonium

International Nuclear Information System (INIS)

Alcorn, C.; Brodovitch, J.-C.; Ghandi, K.; Kennedy, A.; Percival, P.W.; Smith, M.

2011-01-01

Safe operation of a supercritical water cooled reactor requires knowledge of the reaction kinetics of transient species formed by the radiolysis of water in the temperature range 300-650"oC. By using a light isotope of the H·atom, it is possible to study its chemistry in water over this range of temperatures. Arguably, the most important reaction to study is that of the H·atom with the bulk solvent. This reaction could provide an in situ source of H_2 gas, which is added to CANDU reactors to suppress oxidative corrosion. The work described here concerns studies of the reaction of muonium with H_2O and D_2O at temperatures up to 450"oC.

Thermo-Kinetic Investigation of Comparative Ligand Effect on Cysteine Iron Redox Reaction

OpenAIRE

Rizvi, Masood Ahmad; Teshima, Norio; Maqsood, Syed Raashid; Akhoon, Showket Ahmad; Peerzada, Ghulam Mustafa

2015-01-01

Transition metal ions in their free state bring unwanted biological oxidations generating oxidative stress. The ligand modulated redox potential can be indispensable in prevention of such oxidative stress by blocking the redundant bio-redox reactions. In this study we investigated the comparative ligand effect on the thermo-kinetic aspects of biologically important cysteine iron (III) redox reaction using spectrophotometric and potentiometric methods. The results were corroborated...

Reaction kinetic analysis of reactor surveillance data

Energy Technology Data Exchange (ETDEWEB)

Yoshiie, T., E-mail: yoshiie@rri.kyoto-u.ac.jp [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka-fu 590-0494 (Japan); Kinomura, A. [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka-fu 590-0494 (Japan); Nagai, Y. [The Oarai Center, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan)

2017-02-15

In the reactor pressure vessel surveillance data of a European-type pressurized water reactor (low-Cu steel), it was found that the concentration of matrix defects was very high, and a large number of precipitates existed. In this study, defect structure evolution obtained from surveillance data was simulated by reaction kinetic analysis using 15 rate equations. The saturation of precipitation and the growth of loops were simulated, but it was not possible to explain the increase in DBTT on the basis of the defect structures. The sub-grain boundary segregation of solutes was discussed for the origin of the DBTT increase.

Investigation of the kinetics and mechanism of the glycerol chlorination reaction using gas chromatography–mass spectrometry

Directory of Open Access Journals (Sweden)

JUN WANG

2010-01-01

Full Text Available As a primary by-product in biodiesel production, glycerol can be used to prepare an important fine chemical, epichlorohydrin, by the glycerol chlorination reaction. Although this process has been applied in industrial production, unfortunately, less attention has been paid to the analysis and separation of the compounds in the glycerol chlorination products. In this study, a convenient and accurate method to determine the products in glycerol chlorination reaction was established and based on the results the kinetic mechanism of the reaction was investigated. The structure of main products, including 1,3--dichloropropan-2-ol, 2,3-dichloropropan-1-ol, 3-chloro-1,2-propanediol, 2-chloro-1,3-propanediol and glycerol was ascertained by gas chromatography–mass spectrometry and the isomers of the products were distinguished. Apidic acid was considered as the best catalyst because of its excellent catalytic effect and high boiling point. The mechanism of the glycerol chlorination reaction was proposed and a new kinetic model was developed. Kinetic equations of the process in the experimental range were obtained by data fitting and the activation energies of each tandem reaction were 30.7, 41.8, 29.4 and 49.5 kJ mol-1, respectively. This study revealed the process and mechanism of the kinetics and provides the theoretical basis for engineering problems.

Kinetics of catalytic reactions solutions manual

CERN Document Server

Vannice, M Albert

2005-01-01

Including countless exercises and worked examples, this advanced reference work and textbook will be extremely useful for the work of many industrial scientists. It teaches readers to design kinetic experiments involving heterogeneous catalysts, to characterize these catalysts, to acquire rate data, to find heat and mass transfer limitations in these data, to select reaction models, to derive rate expressions based on these models, and to assess the consistency of these rate equations.

Kinetic isotope effects in reaction of ferment oxidation of tritium-labelled D-galactosamine

International Nuclear Information System (INIS)

Akulov, G.P.; Korsakova, N.A.

1992-01-01

Primary, secondary and intramolecular kinetic isotopic effects in reaction of ferment oxidation of D-galactosamine labelled by tritium in position 6, were measured. When comparing values of the effects with previously obtained results for similar reaction D-[6- 3 H]galactose, it was ascertained that the presence of aminogroup in galactopyranosyl mainly affects kinetics of substrate-ferment complex formation stage. The possibility to use kinetic isotope effects for increase in molar activity of D-galactosamine, labelled by tritium in position 6, is shown

Presenting a new kinetic model for methanol to light olefins reactions over a hierarchical SAPO-34 catalyst using the Langmuir-Hinshelwood-Hougen-Watson mechanism

Science.gov (United States)

Javad Azarhoosh, Mohammad; Halladj, Rouein; Askari, Sima

2017-10-01

In this study, a new kinetic model for methanol to light olefins (MTO) reactions over a hierarchical SAPO-34 catalyst using the Langmuir-Hinshelwood-Hougen-Watson (LHHW) mechanism was presented and the kinetic parameters was obtained using a genetic algorithm (GA) and genetic programming (GP). Several kinetic models for the MTO reactions have been presented. However, due to the complexity of the reactions, most reactions are considered lumped and elementary, which cannot be deemed a completely accurate kinetic model of the process. Therefore, in this study, the LHHW mechanism is presented as kinetic models of MTO reactions. Because of the non-linearity of the kinetic models and existence of many local optimal points, evolutionary algorithms (GA and GP) are used in this study to estimate the kinetic parameters in the rate equations. Via the simultaneous connection of the code related to modelling the reactor and the GA and GP codes in the MATLAB R2013a software, optimization of the kinetic models parameters was performed such that the least difference between the results from the kinetic models and experiential results was obtained and the best kinetic parameters of MTO process reactions were achieved. A comparison of the results from the model with experiential results showed that the present model possesses good accuracy.

Pressure-dependent kinetics of initial reactions in iso-octane pyrolysis.

Science.gov (United States)

Ning, HongBo; Gong, ChunMing; Li, ZeRong; Li, XiangYuan

2015-05-07

This study focuses on the studies of the main pressure-dependent reaction types of iso-octane (iso-C8H18) pyrolysis, including initial C-C bond fission of iso-octane, isomerization, and β-scission reactions of the alkyl radicals produced by the C-C bond fission of iso-octane. For the C-C bond fission of iso-octane, the minimum energy potentials are calculated at the CASPT2(2e,2o)/6-31+G(d,p)//CAS(2e,2o)/6-31+G(d,p) level of theory. For the isomerization and the β-scission reactions of the alkyl radicals, the optimization of the geometries and the vibrational frequencies of the reactants, transition states, and products are performed at the B3LYP/CBSB7 level, and their single point energies are calculated by using the composite CBS-QB3 method. Variable reaction coordinate transition state theory (VRC-TST) is used for the high-pressure limit rate constant calculation and Rice-Ramsperger-Kassel-Marcus/master equation (RRKM/ME) is used to calculate the pressure-dependent rate constants of these channels with pressure varying from 0.01-100 atm. The rate constants obtained in this work are in good agreement with those available from literatures. We have updated the rate constants and thermodynamic parameters for species involved in these reactions into a current chemical kinetic mechanism and also have improved the concentration profiles of main products such as C3H6 and C4H6 in the shock tube pyrolysis of iso-octane. The results of this study provide insight into the pyrolysis of iso-octane and will be helpful in the future development of branched paraffin kinetic mechanisms.

Kinetics of reactions of chromium, molybdenum and tungsten hexacarbonyls with hydroxylamine and trimethylamine oxide

International Nuclear Information System (INIS)

Maksakov, V.A.; Ershova, V.A.

1994-01-01

Mechanism of M(CO) 6 (M = Cr, Mo, W) reaction with hydroxylamine was studied. On the basis of kinetic data it was ascertained that as a result of the reaction CO oxidation to CO 2 and intramolecular transfer of amine formed to the central atom of metal occur. Mechanisms of M(CO) 6 reactions with hydroxylamine and trimethylamine oxide are compared

Kinetic study of enzymatic hydrolysis of potato starch

Directory of Open Access Journals (Sweden)

Óscar Fernando Castellanos Domínguez

2004-01-01

Full Text Available This article describes the kinetic study of potato starch enzymatic hydrolysis using soluble enzymes (Novo Nordisk. Different assays divided into four groups were used: reaction time (with which it was possible to reduce the 48-72 hour duration reported in the literature to 16 hours with comparable productivity levels; selecting the set of enzymes to be used (different types were evaluated - BAN and Termamyl as alfa-amylases during dextrinisation stage, and AMG, Promozyme and Fungamyl for sacarification reaction- identifying those presenting the best performance during hydrolysis.Reaction conditions were optimised for the process's two stages (destrinisation and sacarification. Enzyme dose, calcium cofactor concentration, pH, temperature and agitation speed were studied for the first stage. Enzyme ratio, pH and agitation speed were studied for sacarification; the latter parameter reported values having no antecedents in the literature (60 rpm and 30 rpm for first and second reactions, respectively. Michaelis Menten kinetics were calculated once conditions had been optimised, varying substrate from 10-50% P/V, obtaining km and Vmax kinetic parameters for each reaction. A kinetic model was found according to local working conditions which was able to explain potato starch conversion to glucose syrup, achieving 96 dextrose equivalents by the end of the reaction, being well within the maximum range reported in the literature (94-98.Laboratory equipment was constructed prior to carrying out assays which was able to reproduce and improve the conditions reported in the literature, making it a useful, reliable tool for use in assays returning good results.

Bacillus anthracis o-succinylbenzoyl-CoA synthetase: reaction kinetics and a novel inhibitor mimicking its reaction intermediate †

Science.gov (United States)

Tian, Yang; Suk, Dae-Hwan; Cai, Feng; Crich, David; Mesecar, Andrew D.

2009-01-01

O-succinylbenzoyl-CoA (OSB-CoA) synthetase (EC 6.2.1.26) catalyzes the ATP-dependent condensation of o-succinylbenzoate (OSB) and CoA to form OSB-CoA, the fourth step of the menaquinone biosynthetic pathway in Bacillus anthracis. Gene knockout studies have highlighted this enzyme as a potential target for the discovery of new antibiotics. Here we report the first studies on the kinetic mechanism of B. anthracis OSB-CoA synthetase, classifying it as an ordered Bi Uni Uni Bi ping-pong mechanism. Through a series of pre-steady-state and steady-state kinetic studies in conjunction with direct-binding studies, it is demonstrated that CoA, the last substrate to bind, strongly activates the first half-reaction after the first round of turnover. The activation of the first-half reaction is most likely achieved by CoA stabilizing conformations of the enzyme in the ‘F’ form, which slowly isomerize back to the E form. Thus, the kinetic mechanism of OSB-CoA synthetase may be more accurately described as an ordered Bi Uni Uni Bi Iso ping-pong mechanism. The substrate specificity of OSB-CoA synthetase was probed using a series of OSB analogs with alterations in the carboxylate groups. OSB-CoA shows a strong preference for OSB over all of the analogs tested as none were active except 4-(2-trifluoromethylphenyl)-4-oxobutyric acid which exhibited a 100-fold decrease in kcat/Km. Based on an understanding of OSB-CoA synthetase’s kinetic mechanism and substrate specificity, a reaction intermediate analog of OSB-AMP, 5’-O-(N-(2-trifluoromethylphenyl)-4-oxobutyl) adenosine sulfonamide (TFMP-butyl-AMS), was designed and synthesized. This inhibitor was found to be an uncompetitive inhibitor to CoA and a mixed-type inhibitor to ATP and OSB with low micromolar inhibition constants. Collectively, these results should serve as an important forerunner to more detailed and extensive inhibitor design studies aimed at developing lead compounds against the OSB-CoA synthetase class of

Pre-recombination quenching of the radiation induced fluorescence as the approach to study kinetics of ion-molecular reactions

International Nuclear Information System (INIS)

Borovkov, V.I.; Ivanishko, I.S.

2011-01-01

This study deals with the geminate ion recombination in the presence of bulk scavengers, that is the so-called scavenger problem, as well as with the effect of the scavenging reaction on the radiation-induced recombination fluorescence. have proposed a method to determine the rate constant of the bulk reaction between neutral scavengers and one of the geminate ions if the ion-molecular reaction prevented the formation of electronically excited states upon recombination involving a newly formed ion. If such pre-recombination quenching of the radiation-induced fluorescence took place, it manifested itself as a progressive decrease in the decay of the fluorescence intensity. The relative change in the fluorescence decay as caused by the scavengers was believed to be closely related to the kinetics of the scavenging reaction. The goal of the present study is to support this method, both computationally and experimentally because there are two factors, which cast doubt on the intuitively obvious approach to the scavenger problem: spatial correlations between the particles involved and the drift of the charged reagent in the electric field of its geminate partner. Computer simulation of geminate ions recombination with an explicit modeling of the motion trajectories of scavengers has been performed for media of low dielectric permittivity, i.e. for the maximal Coulomb interaction between the ions. The simulation has shown that upon continuous diffusion of the particles involved, the joint effect of the two above factors can be considered as insignificant with a high accuracy. Besides, it is concluded then that the method of pre-recombination quenching could be applied to study parallel and consecutive reactions where the yields of excited states in the reaction pathways are different with the use of very simple analytical relations of the formal chemical kinetics. The conclusion has been confirmed experimentally by the example of the reactions of electron transfer from

Kinetics of solid-gas reactions characterized by scanning AC nano-calorimetry with application to Zr oxidation

International Nuclear Information System (INIS)

Xiao, Kechao; Lee, Dongwoo; Vlassak, Joost J.

2014-01-01

Scanning AC nano-calorimetry is a recently developed experimental technique capable of measuring the heat capacity of thin-film samples of a material over a wide range of temperatures and heating rates. Here, we describe how this technique can be used to study solid-gas phase reactions by measuring the change in heat capacity of a sample during reaction. We apply this approach to evaluate the oxidation kinetics of thin-film samples of zirconium in air. The results confirm parabolic oxidation kinetics with an activation energy of 0.59 ± 0.03 eV. The nano-calorimetry measurements were performed using a device that contains an array of micromachined nano-calorimeter sensors in an architecture designed for combinatorial studies. We demonstrate that the oxidation kinetics can be quantified using a single sample, thus enabling high-throughput mapping of the composition-dependence of the reaction rate.

Reaction kinetics of free fatty acids esterification in palm fatty acid distillate using coconut shell biochar sulfonated catalyst

Science.gov (United States)

Hidayat, Arif; Rochmadi, Wijaya, Karna; Budiman, Arief

2015-12-01

Recently, a new strategy of preparing novel carbon-based solid acids has been developed. In this research, the esterification reactions of Palm Fatty Acid Distillate (PFAD) with methanol, using coconut shell biochar sulfonated catalyst from biomass wastes as catalyst, were studied. In this study, the coconut shell biochar sulfonated catalysts were synthesized by sulfonating the coconut shell biochar using concentrated H2SO4. The kinetics of free fatty acid (FFA) esterification in PFAD using a coconut shell biochar sulfonated catalyst was also studied. The effects of the mass ratio of catalyst to oil (1-10%), the molar ratio of methanol to oil (6:1-12:1), and the reaction temperature (40-60°C) were studied for the conversion of PFAD to optimize the reaction conditions. The results showed that the optimal conditions were an methanol to PFAD molar ratio of 12:1, the amount of catalyst of 10%w, and reaction temperature of 60°C. The proposed kinetic model shows a reversible second order reaction and represents all the experimental data satisfactorily, providing deeper insight into the kinetics of the reaction.

Kinetics of the reaction between H· and superheated water probed with muonium

Energy Technology Data Exchange (ETDEWEB)

Alcorn, C. [Mount Allison Univ., Sackville, NB (Canada); Brodovitch, J.-C. [Simon Fraser Univ., Burnaby, BC (Canada); Ghandi, K.; Kennedy, A. [Mount Allison Univ., Sackville, NB (Canada); Percival, P.W. [Simon Fraser Univ., Burnaby, BC (Canada); TRIUMF, Vancouver, BC (Canada); Smith, M. [Mount Allison Univ., Sackville, NB (Canada)

2011-07-01

Safe operation of a supercritical water cooled reactor requires knowledge of the reaction kinetics of transient species formed by the radiolysis of water in the temperature range 300-650{sup o}C. By using a light isotope of the H·atom, it is possible to study its chemistry in water over this range of temperatures. Arguably, the most important reaction to study is that of the H·atom with the bulk solvent. This reaction could provide an in situ source of H{sub 2} gas, which is added to CANDU reactors to suppress oxidative corrosion. The work described here concerns studies of the reaction of muonium with H{sub 2}O and D{sub 2}O at temperatures up to 450{sup o}C.

Kinetics of the gas-phase tritium oxidation reaction

International Nuclear Information System (INIS)

Failor, R.A.

1989-01-01

Homogeneous gas-phase kinetics of tritium oxidation (2T 2 + O 2 →2T 2 O) have been studied with a model that accounts explicitly for radiolysis of the major species and the kinetics of the subsequent reactions of ionic, excited-state, and neutral species. Results from model calculations are given for 10 -4 -1.0 mol% T 2 in O 2 (298 K, 1 atm). As the reaction evolves three different mechanisms control T 2 O production, each with a different overall rate expression and a different order with respect to the T 2 concentration. The effects of self-radiolysis of pure T 2 on the tritium oxidation reaction were calculated. Tritium atoms, the primary product of T 2 self-radiolysis, altered the oxidation mechanism only during the first few seconds following the initiation of the T 2 -O 2 reaction. Ozone, an important intermediate in T 2 oxidation, was monitored in-situ by U.V. absorption spectroscopy for 0.01-1.0 mol% T 2 an 1 atm O 2 . The shape of the experimental ozone time profile agreed with the model predictions. As predicted, the measured initial rate of ozone production varied linearly with initial T 2 concentration ([T 2 ] 0.6 o ), but at an initial rate one-third the predicted value. The steady-state ozone concentration ([O 3 ]ss) was predicted to be dependent on [T 2 ] 0.3 o , but the measured value was [T 2 ] 0.6 o , resulting in four times higher [O 3 ]ss than predicted for a 1.0% T 2 -O 2 mixture. Adding H 2 to the T 2 -O 2 mixture, to provide insight into the differences between the radiolytic and chemical behavior of the tritium, produced a greater decrease in [O 3 ]ss than predicted. Adjusting the reaction cell surface-to-volume ratio showed implications of minor surface removal of ozone

Thermogravimetric analysis and kinetic study of bamboo waste treated by Echinodontium taxodii using a modified three-parallel-reactions model.

Science.gov (United States)

Yu, Hongbo; Liu, Fang; Ke, Ming; Zhang, Xiaoyu

2015-06-01

In this study, the effect of pretreatment with Echinodontium taxodii on thermal decomposition characteristics and kinetics of bamboo wastes was investigated by thermogravimetric analysis. The results showed fungal pretreatment can enhance the thermal degradation of bamboo. The negative effect of extractives in bamboo on the thermal decomposition can be decreased by the pretreatment. A modified three-parallel-reactions model based on isolated lignin was firstly proposed to study pyrolysis kinetics of bamboo lignocellulose. Kinetic analysis showed that with increasing pretreatment time fungal delignification was enhanced to transform the lignin component with high activation energy into that with low activation energy and raise the cellulose content in bamboo, making the thermal decomposition easier. These results demonstrated fungal pretreatment provided a potential way to improve thermal conversion efficiency of bamboo. Copyright © 2015 Elsevier Ltd. All rights reserved.

A combined high-temperature experimental and theoretical kinetic study of the reaction of dimethyl carbonate with OH radicals

KAUST Repository

Khaled, Fathi; Giri, Binod; Szőri, Milá n; Mai, Tam V.-T.; Huynh, Lam K.; Farooq, Aamir

2017-01-01

The reaction kinetics of dimethyl carbonate (DMC) and OH radicals were investigated behind reflected shock waves over the temperature range of 872-1295 K and at pressures near 1.5 atm. Reaction progress was monitored by detecting OH radicals at 306.69 nm using a UV laser absorption technique. The rate coefficients for the reaction of DMC with OH radicals were extracted using a detailed kinetic model developed by Glaude et al. (Proc. Combust. Inst. 2005, 30(1), 1111-1118). The experimental rate coefficients can be expressed in Arrhenius form as: kexpt'l = 5.15 × 10(13) exp(-2710.2/T) cm(3) mol(-1) s(-1). To explore the detailed chemistry of the DMC + OH reaction system, theoretical kinetic analyses were performed using high-level ab initio and master equation/Rice-Ramsperger-Kassel-Marcus (ME/RRKM) calculations. Geometry optimization and frequency calculations were carried out at the second-order Møller-Plesset (MP2) perturbation level of theory using Dunning's augmented correlation consistent-polarized valence double-ζ basis set (aug-cc-pVDZ). The energy was extrapolated to the complete basis set using single point calculations performed at the CCSD(T)/cc-pVXZ (where X = D, T) level of theory. For comparison purposes, additional ab initio calculations were also carried out using composite methods such as CBS-QB3, CBS-APNO, G3 and G4. Our calculations revealed that the H-abstraction reaction of DMC by OH radicals proceeds via an addition elimination mechanism in an overall exothermic process, eventually forming dimethyl carbonate radicals and H2O. Theoretical rate coefficients were found to be in excellent agreement with those determined experimentally. Rate coefficients for the DMC + OH reaction were combined with literature rate coefficients of four straight chain methyl ester + OH reactions to extract site-specific rates of H-abstraction from methyl esters by OH radicals.

Dynamic Model of Basic Oxygen Steelmaking Process Based on Multizone Reaction Kinetics: Modeling of Decarburization

Science.gov (United States)

Rout, Bapin Kumar; Brooks, Geoffrey; Akbar Rhamdhani, M.; Li, Zushu; Schrama, Frank N. H.; Overbosch, Aart

2018-03-01

In a previous study by the authors (Rout et al. in Metall Mater Trans B 49:537-557, 2018), a dynamic model for the BOF, employing the concept of multizone kinetics was developed. In the current study, the kinetics of decarburization reaction is investigated. The jet impact and slag-metal emulsion zones were identified to be primary zones for carbon oxidation. The dynamic parameters in the rate equation of decarburization such as residence time of metal drops in the emulsion, interfacial area evolution, initial size, and the effects of surface-active oxides have been included in the kinetic rate equation of the metal droplet. A modified mass-transfer coefficient based on the ideal Langmuir adsorption equilibrium has been proposed to take into account the surface blockage effects of SiO2 and P2O5 in slag on the decarburization kinetics of a metal droplet in the emulsion. Further, a size distribution function has been included in the rate equation to evaluate the effect of droplet size on reaction kinetics. The mathematical simulation indicates that decarburization of the droplet in the emulsion is a strong function of the initial size and residence time. A modified droplet generation rate proposed previously by the authors has been used to estimate the total decarburization rate by slag-metal emulsion. The model's prediction shows that about 76 pct of total carbon is removed by reactions in the emulsion, and the remaining is removed by reactions at the jet impact zone. The predicted bath carbon by the model has been found to be in good agreement with the industrially measured data.

Dynamic Model of Basic Oxygen Steelmaking Process Based on Multizone Reaction Kinetics: Modeling of Decarburization

Science.gov (United States)

Rout, Bapin Kumar; Brooks, Geoffrey; Akbar Rhamdhani, M.; Li, Zushu; Schrama, Frank N. H.; Overbosch, Aart

2018-06-01

In a previous study by the authors (Rout et al. in Metall Mater Trans B 49:537-557, 2018), a dynamic model for the BOF, employing the concept of multizone kinetics was developed. In the current study, the kinetics of decarburization reaction is investigated. The jet impact and slag-metal emulsion zones were identified to be primary zones for carbon oxidation. The dynamic parameters in the rate equation of decarburization such as residence time of metal drops in the emulsion, interfacial area evolution, initial size, and the effects of surface-active oxides have been included in the kinetic rate equation of the metal droplet. A modified mass-transfer coefficient based on the ideal Langmuir adsorption equilibrium has been proposed to take into account the surface blockage effects of SiO2 and P2O5 in slag on the decarburization kinetics of a metal droplet in the emulsion. Further, a size distribution function has been included in the rate equation to evaluate the effect of droplet size on reaction kinetics. The mathematical simulation indicates that decarburization of the droplet in the emulsion is a strong function of the initial size and residence time. A modified droplet generation rate proposed previously by the authors has been used to estimate the total decarburization rate by slag-metal emulsion. The model's prediction shows that about 76 pct of total carbon is removed by reactions in the emulsion, and the remaining is removed by reactions at the jet impact zone. The predicted bath carbon by the model has been found to be in good agreement with the industrially measured data.

Thermodynamic and Kinetic Response of Microbial Reactions to High CO2.

Science.gov (United States)

Jin, Qusheng; Kirk, Matthew F

2016-01-01

Geological carbon sequestration captures CO 2 from industrial sources and stores the CO 2 in subsurface reservoirs, a viable strategy for mitigating global climate change. In assessing the environmental impact of the strategy, a key question is how microbial reactions respond to the elevated CO 2 concentration. This study uses biogeochemical modeling to explore the influence of CO 2 on the thermodynamics and kinetics of common microbial reactions in subsurface environments, including syntrophic oxidation, iron reduction, sulfate reduction, and methanogenesis. The results show that increasing CO 2 levels decreases groundwater pH and modulates chemical speciation of weak acids in groundwater, which in turn affect microbial reactions in different ways and to different extents. Specifically, a thermodynamic analysis shows that increasing CO 2 partial pressure lowers the energy available from syntrophic oxidation and acetoclastic methanogenesis, but raises the available energy of microbial iron reduction, hydrogenotrophic sulfate reduction and methanogenesis. Kinetic modeling suggests that high CO 2 has the potential of inhibiting microbial sulfate reduction while promoting iron reduction. These results are consistent with the observations of previous laboratory and field studies, and highlight the complexity in microbiological responses to elevated CO 2 abundance, and the potential power of biogeochemical modeling in evaluating and quantifying these responses.

Thermodynamic and kinetic response of microbial reactions to high CO2

Directory of Open Access Journals (Sweden)

Qusheng Jin

2016-11-01

Full Text Available Geological carbon sequestration captures CO2 from industrial sources and stores the CO2 in subsurface reservoirs, a viable strategy for mitigating global climate change. In assessing the environmental impact of the strategy, a key question is how microbial reactions respond to the elevated CO2 concentration. This study uses biogeochemical modeling to explore the influence of CO2 on the thermodynamics and kinetics of common microbial reactions in subsurface environments, including syntrophic oxidation, iron reduction, sulfate reduction, and methanogenesis. The results show that increasing CO2 levels decreases groundwater pH and modulates chemical speciation of weak acids in groundwater, which in turn affect microbial reactions in different ways and to different extents. Specifically, a thermodynamic analysis shows that increasing CO2 partial pressure lowers the energy available from syntrophic oxidation and acetoclastic methanogenesis, but raises the available energy of microbial iron reduction, hydrogenotrophic sulfate reduction and methanogenesis. Kinetic modeling suggests that high CO2 has the potential of inhibiting microbial sulfate reduction while promoting iron reduction. These results are consistent with the observations of previous laboratory and field studies, and highlight the complexity in microbiological responses to elevated CO2 abundance, and the potential power of biogeochemical modeling in evaluating and quantifying these responses.

Kinetics of the hydrogen production reaction in a copper-chlorine water splitting plant

International Nuclear Information System (INIS)

Zamfirescu, C.; Naterer, G.F.; Dincer, I.

2009-01-01

The exothermic reaction of HCl with particulate Cu occurs during hydrogen production step in the thermochemical copper-chlorine (Cu-Cl) water splitting cycle. In this paper, this chemical reaction is modeled kinetically, and a parametric study is performed to determine the influences of particle size, temperature and molar ratios on the reaction kinetics. It is determined that the residence time of copper particles varies between 10 and 100 s, depending on the operating conditions. The hydrogen conversion at equilibrium varies between 55 and 85%, depending on the reaction temperature. The heat flux at the particle surface, caused by the exothermic enthalpy of reaction, reaches about 3,000 W/m 2 when the particle shrinks to 0.1% from its initial size. A numerical algorithm is developed to solve the moving boundary Stefan problem with a chemical reaction. It predicts the shrinking of copper particles based on the hypothesis that the chemical reaction and heat transfer are decoupled. The model allows for estimation of the temperature of the copper particle, assumed spherical, in the radial direction. The maximum temperature at the interface is higher than the melting point of CuCl by 10-50 o C, depending on the assumed operating conditions. (author)

Kinetic Models Study of Hydrogenation of Aromatic Hydrocarbons in Vacuum Gas Oil and Basrah Crude Oil Reaction

Directory of Open Access Journals (Sweden)

Muzher M. Ibraheem

2013-05-01

Full Text Available             The aim of this research is to study the kinetic reaction models for catalytic hydrogenation of aromatic content for Basrah crude oil (BCO and vacuum gas oil (VGO derived from Kirkuk crude oil which has the boiling point rang of (611-833K.            This work is performed using a hydrodesulphurization (HDS pilot plant unit located in AL-Basil Company. A commercial (HDS catalyst cobalt-molybdenum (Co-Mo supported in alumina (γ-Al2O3 is used in this work. The feed is supplied by North Refinery Company in Baiji. The reaction temperatures range is (600-675 K over liquid hourly space velocity (LHSV range of (0.7-2hr-1 and hydrogen pressure is 3 MPa with H2/oil ratio of 300 of Basrah Crude oil (BCO, while the corresponding conditions for vacuum gas oil (VGO are (583-643 K, (1.5-3.75 hr-1, 3.5 MPa and 250  respectively .            The results showed that the reaction kinetics is of second order for both types of feed. Activation energies are found to be 30.396, 38.479 kJ/mole for Basrah Crude Oil (BCO and Vacuum Gas Oil (VGO respectively.

Multiresponse kinetic modelling of Maillard reaction and caramelisation in a heated glucose/wheat flour system.

Science.gov (United States)

Kocadağlı, Tolgahan; Gökmen, Vural

2016-11-15

The study describes the kinetics of the formation and degradation of α-dicarbonyl compounds in glucose/wheat flour system heated under low moisture conditions. Changes in the concentrations of glucose, fructose, individual free amino acids, lysine and arginine residues, glucosone, 1-deoxyglucosone, 3-deoxyglucosone, 3,4-dideoxyglucosone, 5-hydroxymethyl-2-furfural, glyoxal, methylglyoxal and diacetyl concentrations were determined to form a multiresponse kinetic model for isomerisation and degradation reactions of glucose. Degradation of Amadori product mainly produced 1-deoxyglucosone. Formation of 3-deoxyglucosone proceeded directly from glucose and also Amadori product degradation. Glyoxal formation was predominant from glucosone while methylglyoxal and diacetyl originated from 1-deoxyglucosone. Formation of 5-hydroxymethyl-2-furfural from fructose was found to be a key step. Multi-response kinetic modelling of Maillard reaction and caramelisation simultaneously indicated quantitatively predominant parallel and consecutive pathways and rate limiting steps by estimating the reaction rate constants. Copyright © 2016 Elsevier Ltd. All rights reserved.

A kinetic reaction model for biomass pyrolysis processes in Aspen Plus

International Nuclear Information System (INIS)

Peters, Jens F.; Banks, Scott W.; Bridgwater, Anthony V.; Dufour, Javier

2017-01-01

Highlights: • Predictive kinetic reaction model applicable to any lignocellulosic feedstock. • Calculates pyrolysis yields and product composition as function of reactor conditions. • Detailed modelling of product composition (33 model compounds for the bio-oil). • Good agreement with literature regarding yield curves and product composition. • Successful validation with pyrolysis experiments in bench scale fast pyrolysis rig. - Abstract: This paper presents a novel kinetic reaction model for biomass pyrolysis processes. The model is based on the three main building blocks of lignocellulosic biomass, cellulose, hemicellulose and lignin and can be readily implemented in Aspen Plus and easily adapted to other process simulation software packages. It uses a set of 149 individual reactions that represent the volatilization, decomposition and recomposition processes of biomass pyrolysis. A linear regression algorithm accounts for the secondary pyrolysis reactions, thus allowing the calculation of slow and intermediate pyrolysis reactions. The bio-oil is modelled with a high level of detail, using up to 33 model compounds, which allows for a comprehensive estimation of the properties of the bio-oil and the prediction of further upgrading reactions. After showing good agreement with existing literature data, our own pyrolysis experiments are reported for validating the reaction model. A beech wood feedstock is subjected to pyrolysis under well-defined conditions at different temperatures and the product yields and compositions are determined. Reproducing the experimental pyrolysis runs with the simulation model, a high coincidence is found for the obtained fraction yields (bio-oil, char and gas), for the water content and for the elemental composition of the pyrolysis products. The kinetic reaction model is found to be suited for predicting pyrolysis yields and product composition for any lignocellulosic biomass feedstock under typical pyrolysis conditions

1D to 3D diffusion-reaction kinetics of defects in crystals

DEFF Research Database (Denmark)

Trinkaus, H.; Heinisch, H.L.; Barashev, A.V.

2002-01-01

Microstructural features evolving in crystalline solids from diffusion-reaction kinetics of mobile components depend crucially on the dimension of the underlying diffusion process which is commonly assumed to be three-dimensional (3D). In metals, irradiation-induced displacement cascades produce...... clusters of self-interstitials performing 1D diffusion. Changes between equivalent 1D diffusion paths and transversal diffusion result in diffusion-reaction kinetics between one and three dimensions. An analytical approach suggests a single-variable function (master curve) interpolating between the 1D...

Kinetics and mechanism of the gas phase reaction of Cl atoms with iodobenzene

DEFF Research Database (Denmark)

Andersen, Mads Peter Sulbæk; Ponomarev, DA; Nielsen, OJ

2001-01-01

Smog chamber/FTIR techniques were used to study the kinetics and mechanism of the reaction of Cl atoms with iodobenzene (C6H5I) in 20-700 Torr of N-2, air, or O-2 diluent at 296 K. The reaction proceeds with a rate constant k(Cl + QH(5)I) = (3.3 +/- 0.7) x 10(-11) cm(3) molecule(-1) s(-1) to give...

Reaction of diazepam and related benzodiazepines with chlorine. Kinetics, transformation products and in-silico toxicological assessment.

Science.gov (United States)

Carpinteiro, Inmaculada; Rodil, Rosario; Quintana, José Benito; Cela, Rafael

2017-09-01

In this work, the reaction of four benzodiazepines (diazepam, oxazepam, nordazepam and temazepam) during water chlorination was studied by means of liquid chromatography-quadrupole-time of flight-mass spectrometry (LC-QTOF-MS). For those compounds that showed a significant degradation, i.e. diazepam, oxazepam and nordazepam, parameters affecting to the reaction kinetics (pH, chlorine and bromide level) were studied in detail and transformation products were tentatively identified. The oxidation reactions followed pseudofirst-order kinetics with rate constants in the range of 1.8-42.5 M -1  s -1 , 0.13-1.16 M -1  s -1 and 0.04-20.4 M -1  s -1 corresponding to half-life values in the range of 1.9-146 min, 1.8-87 h and 2.5-637 h for oxazepam, nordazepam and diazepam, respectively, depending of the levels of studied parameters. Chlorine and pH affected significantly the reaction kinetics, where an increase of the pH resulted into a decrease of the reaction rate, whereas higher chlorine dosages led to faster kinetics, as expected in this case. The transformation of the studied benzodiazepines occurs mainly at the 1,4-diazepine 7-membered-ring, resulting in ring opening to form benzophenone derivatives or the formation of a 6-membered pyrimidine ring, leading to quinazoline derivatives. The formation of these by-products was also tested in real surface water samples observing kinetics of oxazepam degradation slower in river than in creek water, while the degradation of the two other benzodiazepines occurred only in the simpler sample (creek water). Finally, the acute and chronical toxicity and mutagenicity of precursors and transformation products were estimated using quantitative structure-activity relationship (QSAR) software tools: Ecological Structure Activity Relationships (ECOSAR) and Toxicity Estimation Software Tool (TEST), finding that some transformation products could be more toxic/mutagenic than the precursor drug, but additional test would be needed

Determination of kinetic parameters of heterogeneous isotopic exchange reaction

International Nuclear Information System (INIS)

Huang, Ting-Chia; Tsai, Fuan-Nan

1977-01-01

A mathematical model has been proposed for a heterogeneous isotopic exchange reaction which involves film diffusion, surface chemical reaction and intraparticle diffusion. The exchange equation to predict the exchange fraction as a function of time for the spherical particles immersed in a solution of finite volume has been derived. The relations between the exchange fraction and dimensionless time are plotted with xi(=ak sub(f)/KD sub(e)), xi 1 (=K 1 a 2 /D sub(e)) and final fractional uptake as parameters. From the values of the kinetic parameters xi and xi 1 , the relative importance of each limiting step is discussed. Experimental results of the isotopic exchange reaction of calcium ion in both system CaCO 3 (s)/Ca 2+ (aq) and system calcium type resin Dowex 50W-X8/Ca 2+ (aq) are coincident with the theoretical equation proposed in this study. (auth.)

Reaction kinetics of dolomite rim growth

Science.gov (United States)

Helpa, V.; Rybacki, E.; Abart, R.; Morales, L. F. G.; Rhede, D.; Jeřábek, P.; Dresen, G.

2014-04-01

Reaction rims of dolomite (CaMg[CO3]2) were produced by solid-state reactions at the contacts of oriented calcite (CaCO3) and magnesite (MgCO3) single crystals at 400 MPa pressure, 750-850 °C temperature, and 3-146 h annealing time to determine the reaction kinetics. The dolomite reaction rims show two different microstructural domains. Elongated palisades of dolomite grew perpendicular into the MgCO3 interface with length ranging from about 6 to 41 µm. At the same time, a 5-71 µm wide rim of equiaxed granular dolomite grew at the contact with CaCO3. Platinum markers showed that the original interface is located at the boundary between the granular and palisade-forming dolomite. In addition to dolomite, a 12-80 µm thick magnesio-calcite layer formed between the dolomite reaction rims and the calcite single crystals. All reaction products show at least an axiotactic crystallographic relationship with respect to calcite reactant, while full topotaxy to calcite prevails within the granular dolomite and magnesio-calcite. Dolomite grains frequently exhibit growth twins characterized by a rotation of 180° around one of the equivalent axis. From mass balance considerations, it is inferred that the reaction rim of dolomite grew by counter diffusion of MgO and CaO. Assuming an Arrhenius-type temperature dependence, activation energies for diffusion of CaO and MgO are E a (CaO) = 192 ± 54 kJ/mol and E a (MgO) = 198 ± 44 kJ/mol, respectively.

An experimental and theoretical kinetic study of the reaction of OH radicals with tetrahydrofuran

KAUST Repository

Giri, Binod

2016-06-24

Tetrahydrofuran (CHO, THF) and its alkylated derivatives of the cyclic ether family are considered to be promising future biofuels. They appear as important intermediates during the low-temperature oxidation of conventional hydrocarbon fuels and of heavy biofuels such as long-chain fatty acid methyl esters. The reaction of tetrahydrofuran with OH radicals was investigated in a shock tube, over a temperature range of 800-1340 K and at pressures near 1.5 bar. Hydroxyl radicals were generated by the rapid thermal decomposition of tert-butyl hydroperoxide, and a UV laser absorption technique was used to monitor the mole fraction of OH radicals. High-level CCSD(T)/cc-pV(D,T)Z//MP2/aug-cc-pVDZ quantum chemical calculations were performed to explore the chemistry of the THF+OH reaction system. Our calculations reveal that the THF+OH (R1) reaction proceeds via either direct or indirect H-abstraction from various sites, leading to the formation of tetrahydrofuran-2-yl (THF-R2) or tetrahydrofuran-3-yl (THF-R3) radicals and water. Theoretical kinetic analysis revealed that both channels are important under conditions relevant to combustion. To our knowledge, this is the first direct experimental and theoretical kinetic study of the reaction of tetrahydrofuran with OH radicals at high temperatures. The following theoretical rate expressions (in units of cmmols) are recommended for combustion modeling in the temperature range 800-1350 K: . k1(T)=4.11×1040.16em0ex(TK)2.69exp(1316.80.16em0exKT)2.em0ex0.16em0ex(THF+OH→Products) . k2(T)=6.930.16em0ex×10110.16em0ex(TK)0.41exp(-106.80.16em0exKT)2.em0ex0.16em0ex(THF+OH→THF-R20.16em0ex+H2O) . k3(T)=4.120.16em0ex×1030.16em0ex(TK)3.02exp(456.90.16em0exKT)2.em0ex0.16em0ex(THF+OH→THF-R30.16em0ex+H2O) . .

Kinetics and mechanisms of the reactions of alkyl radicals with oxygen and with complexes of Co(III), Ru(III), and Ni(III)

International Nuclear Information System (INIS)

Kelley, D.

1990-01-01

The kinetics of the reactions of C 2 H 5 radical with Co(NH 3 ) 5 X 2+ , Ru(NH 3 ) 5 X 2+ , and Co(dmgH) 2 (X) (Y) (X = Br, Cl, N 3 , SCN; Y = H 2 O, CH 3 CN) complexes were studied using laser flash photolysis of ethylcobalt complexes. The kinetics were obtained by the kinetic probe method. Some relative rate constants were also determined by a competition method based on ethyl halide product ratios. The kinetics of colligation reactions of a series of alkyl radicals with β-Ni(cyclam) 2+ were studied using flaser flash photolysis of alkylcobalt complexes. Again, the kinetics were obtained by employing the kinetic probe competition method. The kinetics of the unimolecular homolysis of a series of RNi(cyclam)H 2 O 2+ were studied. Activation parameters were obtained for the unimolecular homolysis of C 2 H 5 Ni(cyclam)H 2 O 2+ . Kinetic and thermodynamic data obtained from these reactions were compared with those for the σ-bonded organometallic complexes. The kinetics of the unimolecular homolysis of a series of RNi(cyclam)H 2 O 2+ complexes were studied by monitoring the formation of the oxygen insertion product RO 2 Ni(cyclam)H 2 O 2+ . The higher rate constants for the reactions of alkyl radicals with oxygen in solution, as compared with those measured in the gas phase, were discussed. 30 refs

Kinetic isotope effect studies of the S-adenosylmethionine synthetase reaction

International Nuclear Information System (INIS)

Markham, G.D.; Parkin, D.W.; Schramm, V.L.

1986-01-01

S-adenosylmethionine (AdoMet) synthetase catalyzes a unique substitution reaction at the 5' carbon of MgATP. Kinetic isotope effect (V/K) measurements have been used to investigate the mechanism of AdoMet synthetase from E. coli. Changes in 3 H/ 14 C ratios when AdoMet is formed from a mixture of either ([5'- 14 C]ATP and [5'- 12 C,1'- 3 H]ATP) or ([5'- 3 H]ATP and [5'- 1 H,1'- 14 C]ATP) were examined. The effects of varying the concentrations of the co-substrate methionine and the monovalent cation activator K + were investigated. Substitution of 14 C for 12 C at the 5' position of ATP yields a primary V/K kinetic isotope effect ( 12 C/ 14 C) of 1.128 +/- 0.004 at low K + and methionine concentrations. The observed isotope effect diminishes slightly to 1.107 +/- 0.003 when both K + and methionine are present at saturating concentrations, suggesting that MgATP has only a low commitment to catalysis from at conditions near Vmax. No secondary V/K 3 H isotope effect from [5'- 3 H]ATP was detected ( 1 H/ 3 H) = 0.997 +/- 0.003. The magnitude of the primary 14 C isotope effect and the small secondary 3 H effect demonstrate that AdoMet synthesis occurs with a S/sub N/ 2 transition state which is symmetric with respect to the sulfur nucleophile and the departing tripolyphosphate group

An investigation of the general regularity of size dependence of reaction kinetics of nanoparticles

International Nuclear Information System (INIS)

Cui, Zixiang; Duan, Huijuan; Xue, Yongqiang; Li, Ping

2015-01-01

In the processes of preparation and application of nanomaterials, the chemical reactions of nanoparticles are often involved, and the size of nanoparticles has dramatic influence on the reaction kinetics. Nevertheless, there are many conflicts on regularities of size dependence of reaction kinetic parameters, and these conflicts have not been explained so far. In this paper, taking the reaction of nano-ZnO (average diameter is from 20.96 to 53.31 nm) with acrylic acid solution as a system, the influence regularities of the particle size on the kinetic parameters were researched. The regularities were consistent with that in most literatures, but inconsistent with that in a few of literatures, the reasons for the conflicts were interpreted. The reasons can be attributed to two factors: one is improper data processing for fewer data points, and the other is the difference between solid particles and porous particles. A general regularity of the size dependence of reaction kinetics for solid particles was obtained. The regularity shows that with the size of nanoparticles decreasing, the rate constant and the reaction order increase, while the apparent activation energy and the pre-exponential factor decrease; and the relationships of the logarithm of rate constant, the logarithm of pre-exponential factor, and the apparent activation energy to the reciprocal of the particle size are linear, respectively

CuInSe2 nano-crystallite reaction kinetics using solid state reaction from Cu2Se and In2Se3 powders

International Nuclear Information System (INIS)

Hsiang, Hsing-I; Lu, Li-Hsin; Chang, Yu-Lun; Ray, Dahtong; Yen, Fu-Su

2011-01-01

Highlights: → CuInSe 2 phase increased gradually accompanied with a decrease in γ-In 2 Se 3 and no intermediate phase during calcination. → CuInSe 2 formation from Cu 2 Se and In 2 Se 3 powders follows a one-dimensional diffusion-controlled reaction with apparent activation energy of about 122.5 kJ/mol. → The solid reaction kinetics may be dominated by the diffusion of In 3+ ions. - Abstract: The reaction mechanism and CuInSe 2 formation kinetics using a solid state reaction from Cu 2 Se and In 2 Se 3 powders synthesized using a heating up process were investigated using X-ray diffractomy (XRD) and transmission electron microscopy (TEM). It was observed that the CuInSe 2 phase increased gradually, accompanied with a decrease in γ-In 2 Se 3 with no intermediate phase as the calcination temperature and soaking time were increased. The reaction kinetics was analyzed using the Avrami and polynomial kinetic model, suggesting that CuInSe 2 formation from Cu 2 Se and In 2 Se 3 powders follows a diffusion-controlled reaction with an apparent activation energy of about 122.5-182.3 kJ/mol. Cu 2 Se and In 2 Se 3 phases react and directly transform into CIS without the occurrence of any intermediate phase and the size of the newly formed CuInSe 2 crystallites was close to that of the Cu 2 Se reactant particle based on the TEM results, which indicated that the solid reaction kinetics may be dominated by the diffusion of In 3+ ions.

A combined high-temperature experimental and theoretical kinetic study of the reaction of dimethyl carbonate with OH radicals

KAUST Repository

Khaled, Fathi

2017-02-08

The reaction kinetics of dimethyl carbonate (DMC) and OH radicals were investigated behind reflected shock waves over the temperature range of 872-1295 K and at pressures near 1.5 atm. Reaction progress was monitored by detecting OH radicals at 306.69 nm using a UV laser absorption technique. The rate coefficients for the reaction of DMC with OH radicals were extracted using a detailed kinetic model developed by Glaude et al. (Proc. Combust. Inst. 2005, 30(1), 1111-1118). The experimental rate coefficients can be expressed in Arrhenius form as: kexpt\\'l = 5.15 × 10(13) exp(-2710.2/T) cm(3) mol(-1) s(-1). To explore the detailed chemistry of the DMC + OH reaction system, theoretical kinetic analyses were performed using high-level ab initio and master equation/Rice-Ramsperger-Kassel-Marcus (ME/RRKM) calculations. Geometry optimization and frequency calculations were carried out at the second-order Møller-Plesset (MP2) perturbation level of theory using Dunning\\'s augmented correlation consistent-polarized valence double-ζ basis set (aug-cc-pVDZ). The energy was extrapolated to the complete basis set using single point calculations performed at the CCSD(T)/cc-pVXZ (where X = D, T) level of theory. For comparison purposes, additional ab initio calculations were also carried out using composite methods such as CBS-QB3, CBS-APNO, G3 and G4. Our calculations revealed that the H-abstraction reaction of DMC by OH radicals proceeds via an addition elimination mechanism in an overall exothermic process, eventually forming dimethyl carbonate radicals and H2O. Theoretical rate coefficients were found to be in excellent agreement with those determined experimentally. Rate coefficients for the DMC + OH reaction were combined with literature rate coefficients of four straight chain methyl ester + OH reactions to extract site-specific rates of H-abstraction from methyl esters by OH radicals.

The effects of one-dimensional glide on the reaction kinetics of interstitial clusters

DEFF Research Database (Denmark)

Heinisch, H.L.; Singh, B.N.; Golubov, S.I.

2000-01-01

is therefore 'mixed 1D/3D migration' along a 3D path consisting of 1D segments, The defect reaction kinetics under mixed 1D/3D diffusion are different from pure 1D diffusion and pure 3D diffusion, both of which can be formulated within analytical rate theory models of microstructure evolution under irradiation....... Atomic-scale kinetic Monte Carlo (kMC) defect migration simulations are used to investigate the effects of mixed 1D/3D migration on defect reaction kinetics as a guide for implementing mixed 1D/3D migration into the analytical rate theory. The functional dependence of the sink strength on the size...

Isothermal reaction calorimetry as a tool for kinetic analysis

International Nuclear Information System (INIS)

Zogg, Andreas; Stoessel, Francis; Fischer, Ulrich; Hungerbuehler, Konrad

2004-01-01

Reaction calorimetry has found widespread application for thermal and kinetic analysis of chemical reactions in the context of thermal process safety as well as process development. This paper reviews the most important reaction calorimetric principles (heat-flow, heat-balance, power-compensation, and Peltier principle) and their applications in commercial or scientific devices. The discussion focuses on the different dynamic behavior of the main calorimetric principles during an isothermal reaction measurement. Examples of available reaction calorimeters are further compared considering their detection limit, time constant as well as temperature range. In a second part, different evaluation methods for the isothermally measured calorimetric data are reviewed and discussed. The methods will be compared, focusing especially on the fact that reaction calorimetric data always contains additional informations not directly related to the actual chemical reaction such as heat of mixing, heat of phase-transfer/change processes or simple measurement errors. Depending on the evaluation method applied such disturbances have a significant influence on the calculated reaction enthalpies or rate constants

Reaction kinetics of resveratrol with thiyl and alkoxyl radicals

International Nuclear Information System (INIS)

Dzeba, I.; Mihaljevic, B.

2011-01-01

Complete text of publication follows. Plant derived resveratrol (trans-3,5,4'-trihydroxystilbene) possesses a broad spectrum of biological activities, one of them are very well known its antioxidative properties. Our work aims to provide kinetic data with regard to the reactivity of resveratrol with uninvestigated short-lived bioradicals, identified as mediators in oxidative lipid degradation processes. Radicals of our interest are alkoxyl radicals, well known propagators of the chain free radical reactions in lipids, and thiyl radicals which protect lipids from their degradation pathway, but at the same time cause the isomerization of the double bonds. In order to investigate these reactions of resveratrol laser flash photolysis was used. On the basis of competitive kinetics the rate constants were determined under pseudo-first order conditions in acetonitrile solutions at room temperature. Thiyl radicals were generated indirectly in solution containing 1-octadecanthiol and photosensitive benzophenone in acetonitrile using the light pulses at 347 nm from ruby laser. Tert-butoxyl radicals were generated directly by peroxide bond cleavage from di-tert-butyl peroxide in acetonitrile by light pulses of Nd:YAG at 355 nm, and ruby at 347 nm. Obtained rate constants for the reactions of resveratrol and radicals generated by laser flash photolysis will be summarized and compared with rare literature data for the rate constants of investigated reactions of resveratrol and other radicals generated by pulse radiolysis.

Characterization of excited-state reactions with instant spectra of fluorescence kinetics

International Nuclear Information System (INIS)

Tomin, Vladimir I.; Ushakou, Dzmitryi V.

2015-01-01

Comprehensible knowledge of the excited-state proton transfer processes in organic compounds is overwhelmingly important not only for physics, but also chemistry and Life Sciences, since they play a key role in main processes of photosynthesis and functioning of biological organisms. Moreover compounds with Excited-State Intramolecular Proton Transfer (ESIPT) are in the focus of the interest of scientists throughout the world, because dual fluorescence spectra of such objects corresponding to two forms of molecular structure (normal and photoproduct) are very sensitive to characteristics of molecular microenvironment. This property allows to use such substances as fluorescent probes for diverse applications in chemistry and Life Sciences. But at the same time studying of proton transfer processes is not simple, because this process is characterized by extremely fast times (on picoseconds time scale and less order) and very often contribution of reverse reactions is essentially complicates an interpretation of observed properties of dual fluorescence. Hence, understanding of a role of reversible reactions is crucial for a comprehensive description of all processes accompanying excited state reactions. We discuss new approach for treatment ESIPT reaction on the basis of experimentally measured instant spectra of dual fluorescence and temporal behavior of ratiometric signal of normal to tautomer form intensities. Simple analytical expressions show in transparent way how to distinguish a degree of reverse reaction contribution to ratiometric signal. A validation of the approach under consideration is fulfilled with two different flavonols – 3-hydroxyflavone and 4′-(Dimethylamino)-3-hydroxyflavone – representing two extreme cases in affecting reversible reaction on dual emission. A comparing of new approach and traditional method when we analyze kinetics of separate the N* and T* fluorescence bands decays, has been carried out. - Highlights: • The excited

Characterization of excited-state reactions with instant spectra of fluorescence kinetics

Energy Technology Data Exchange (ETDEWEB)

Tomin, Vladimir I., E-mail: tomin@apsl.edu.pl; Ushakou, Dzmitryi V.

2015-10-15

Comprehensible knowledge of the excited-state proton transfer processes in organic compounds is overwhelmingly important not only for physics, but also chemistry and Life Sciences, since they play a key role in main processes of photosynthesis and functioning of biological organisms. Moreover compounds with Excited-State Intramolecular Proton Transfer (ESIPT) are in the focus of the interest of scientists throughout the world, because dual fluorescence spectra of such objects corresponding to two forms of molecular structure (normal and photoproduct) are very sensitive to characteristics of molecular microenvironment. This property allows to use such substances as fluorescent probes for diverse applications in chemistry and Life Sciences. But at the same time studying of proton transfer processes is not simple, because this process is characterized by extremely fast times (on picoseconds time scale and less order) and very often contribution of reverse reactions is essentially complicates an interpretation of observed properties of dual fluorescence. Hence, understanding of a role of reversible reactions is crucial for a comprehensive description of all processes accompanying excited state reactions. We discuss new approach for treatment ESIPT reaction on the basis of experimentally measured instant spectra of dual fluorescence and temporal behavior of ratiometric signal of normal to tautomer form intensities. Simple analytical expressions show in transparent way how to distinguish a degree of reverse reaction contribution to ratiometric signal. A validation of the approach under consideration is fulfilled with two different flavonols – 3-hydroxyflavone and 4′-(Dimethylamino)-3-hydroxyflavone – representing two extreme cases in affecting reversible reaction on dual emission. A comparing of new approach and traditional method when we analyze kinetics of separate the N* and T* fluorescence bands decays, has been carried out. - Highlights: • The excited

Strain-induced structural changes and chemical reactions. 1: Thermomechanical and kinetic models

International Nuclear Information System (INIS)

Levitas, V.I.; Nesterenko, V.F.; Meyers, M.A.

1998-01-01

Strain-induced chemical reactions were observed recently (Nesterenko et al) in experiments in the shear band in both Ti-Si and Nb-Si mixtures. Reactions can start in the solid state or after melting of at least one component. One of the aims is to find theoretically whether there are possible macroscopic mechanisms of mechanical intensification of the above and other chemical reactions due to plastic shear in the solid state. Continuum thermodynamical theory of structural changes with an athermal kinetics, which includes martensitic phase transformations, plastic strain-induced chemical reactions and polymorphic transformations, is developed at finite strains. The theory includes kinematics, criterion of structural change and extremum principle for determination of all unknown variable parameters for the case with neglected elastic strains. Thermodynamically consistent kinetic theory of thermally activated structural changes is suggested. The concept of the effective temperature is introduced which takes into account that temperature can vary significantly (on 1,000 K) during the chemical reactions under consideration. The theory will be applied in Part 2 of the paper for the description of chemical reactions in the shear band

Transport Properties of a Kinetic Model for Chemical Reactions without Barriers

International Nuclear Information System (INIS)

Alves, Giselle M.; Kremer, Gilberto M.; Soares, Ana Jacinta

2011-01-01

A kinetic model of the Boltzmann equation for chemical reactions without energy barrier is considered here with the aim of evaluating the reaction rate and characterizing the transport coefficient of shear viscosity for the reactive system. The Chapman-Enskog solution of the Boltzmann equation is used to compute the chemical reaction effects, in a flow regime for which the reaction process is close to the final equilibrium state. Some numerical results are provided illustrating that the considered chemical reaction without energy barrier can induce an appreciable influence on the reaction rate and on the transport coefficient of shear viscosity.

In situ synchrotron powder diffraction study of the setting reaction kinetics of magnesium-potassium phosphate cements

Czech Academy of Sciences Publication Activity Database

Viani, Alberto; Pérez-Estébanez, Marta; Pollastri, S.; Gualtieri, A. F.

2016-01-01

Roč. 79, January (2016), s. 344-352 ISSN 0008-8846 R&D Projects: GA MŠk(CZ) LO1219 Keywords : kinetics * reaction * X-ray diffraction * MgO * chemically bonded ceramics Subject RIV: JN - Civil Engineering Impact factor: 4.762, year: 2016 http://www.sciencedirect.com/science/article/pii/S0008884615002690

Kinetics of the Reaction of CO2 with Aqueous Potassium Salt of Taurine and Glycine

NARCIS (Netherlands)

Kumar, P.S.; Hogendoorn, J.A.; Versteeg, G.F.; Feron, P.H.M.

2003-01-01

The kinetics of the reaction between CO2 and aqueous potassium salts of taurine and glycine was measured at 295 K in a stirred-cell reactor with a flat gas–liquid interface. For aqueous potassium taurate solutions, the temperature effect on the reaction kinetics was measured at 285 and 305 K. Unlike

Kinetics of the reaction of CO2 with aqueous potassium salt of taurine and glycine

NARCIS (Netherlands)

Kumar Paramasivam Senthil, P.S.; Hogendoorn, Kees; Versteeg, Geert; Feron, P.H.M.

2003-01-01

The kinetics of the reaction between CO2 and aqueous potassium salts of taurine and glycine was measured at 295 K in a stirred-cell reactor with a flat gas-liquid interface. For aqueous potassium taurate solutions, the temperature effect on the reaction kinetics was measured at 285 and 305 K. Unlike

Elucidation of reaction mechanism for m -cresol hydrodeoxygenation over Fe based catalysts: A kinetic study

Energy Technology Data Exchange (ETDEWEB)

Hong, Yongchun; Wang, Yong

2017-09-01

Fe based catalysts are promising for hydrodeoxygenation (HDO) of lignin derived phenolics due to their high selectivity for aromatics. In this work, the reaction mechanism of m-cresol HDO on Fe catalysts and the kinetic consequence with Pd addition were elucidated by examining the effect of H2, H2O and m-cresol pressures on toluene formation rate on Fe and PdFe catalysts. A direct CO bond cleavage mechanism is proposed for HDO catalysis on both Fe and PdFe catalysts, while Pd provides a facilitated reaction pathway at the PdFe interface and therefore promotes the catalysis on Fe without changing the high selectivity towards aromatics.

A kinetic study of the electrochemical hydrogenation of ethylene

International Nuclear Information System (INIS)

Sedighi, S.; Gardner, C.L.

2010-01-01

In this study, we have examined the kinetics of the electrochemical hydrogenation of ethylene in a PEM reactor. While in itself this reaction is of little industrial interest, this reaction can be looked upon as a model reaction for many of the important hydrogenation processes including the refining of heavy oils and the hydrogenation of vegetable oils. To study the electrochemical hydrogenation of ethylene, several experimental techniques have been used including polarization measurements, measurement of the composition of the exit gases and potential step, transient measurements. The results show that the hydrogenation reaction proceeds rapidly and essentially to completion. By fitting the experimental transient data to the results from a zero-dimensional mathematical model of the process, a set of kinetic parameters for the reactions has been obtained that give generally good agreement with the experimental results. It seems probable that similar experimental techniques could be used to study the electrochemical hydrogenation of other unsaturated organic molecules of more industrial significance.

Oxidation of L-cystine by chromium(VI) - a kinetic study | Kumar ...

African Journals Online (AJOL)

The kinetics of the title reaction was studied spectrophotometrically in HClO4 medium at 380 nm. The data suggested that the order with respect to cystine is fractional, whereas chromium(VI) follows first order kinetics. The reaction was second order in [H+]. Cysteic acid was found to be the main product of oxidation.

SABIO-RK: an updated resource for manually curated biochemical reaction kinetics

Science.gov (United States)

Rey, Maja; Weidemann, Andreas; Kania, Renate; Müller, Wolfgang

2018-01-01

Abstract SABIO-RK (http://sabiork.h-its.org/) is a manually curated database containing data about biochemical reactions and their reaction kinetics. The data are primarily extracted from scientific literature and stored in a relational database. The content comprises both naturally occurring and alternatively measured biochemical reactions and is not restricted to any organism class. The data are made available to the public by a web-based search interface and by web services for programmatic access. In this update we describe major improvements and extensions of SABIO-RK since our last publication in the database issue of Nucleic Acid Research (2012). (i) The website has been completely revised and (ii) allows now also free text search for kinetics data. (iii) Additional interlinkages with other databases in our field have been established; this enables users to gain directly comprehensive knowledge about the properties of enzymes and kinetics beyond SABIO-RK. (iv) Vice versa, direct access to SABIO-RK data has been implemented in several systems biology tools and workflows. (v) On request of our experimental users, the data can be exported now additionally in spreadsheet formats. (vi) The newly established SABIO-RK Curation Service allows to respond to specific data requirements. PMID:29092055

Thermogravimetric analysis and kinetic study of formation of lithium titanate by solid state route

International Nuclear Information System (INIS)

Sonak, Sagar; Jain, Uttam; Sahu, Ashok Kumar; Kumar, Sanjay; Krishnamurthy, Nagaiyar

2015-01-01

The kinetics of formation of lithium titanate from the solid state reaction of lithium carbonate and titanium oxide was studied using non-isothermal thermogravimetric technique. Thermogravimetric data for the reaction of lithium carbonate and titanium oxide was obtained at various heating rates. The methods such as Flynn–Wall–Ozawa and Kissinger–Akahira–Sunose were used to estimate the kinetic parameters from the obtained thermogravimetric data. The average activation energy for the formation of lithium titanate by solid state route was found to be 243 kJ/mol K. The reaction mechanism was determined by the method given by Malek. It was found that the three dimensional diffusion model best describes the reaction kinetics. A kinetic equation describing the reaction is proposed and reaction mechanism is discussed

Kinetics based reaction optimization of enzyme catalyzed reduction of formaldehyde to methanol with synchronous cofactor regeneration.

Science.gov (United States)

Marpani, Fauziah; Sárossy, Zsuzsa; Pinelo, Manuel; Meyer, Anne S

2017-12-01

Enzymatic reduction of carbon dioxide (CO 2 ) to methanol (CH 3 OH) can be accomplished using a designed set-up of three oxidoreductases utilizing reduced pyridine nucleotide (NADH) as cofactor for the reducing equivalents electron supply. For this enzyme system to function efficiently a balanced regeneration of the reducing equivalents during reaction is required. Herein, we report the optimization of the enzymatic conversion of formaldehyde (CHOH) to CH 3 OH by alcohol dehydrogenase, the final step of the enzymatic redox reaction of CO 2 to CH 3 OH, with kinetically synchronous enzymatic cofactor regeneration using either glucose dehydrogenase (System I) or xylose dehydrogenase (System II). A mathematical model of the enzyme kinetics was employed to identify the best reaction set-up for attaining optimal cofactor recycling rate and enzyme utilization efficiency. Targeted process optimization experiments were conducted to verify the kinetically modeled results. Repetitive reaction cycles were shown to enhance the yield of CH 3 OH, increase the total turnover number (TTN) and the biocatalytic productivity rate (BPR) value for both system I and II whilst minimizing the exposure of the enzymes to high concentrations of CHOH. System II was found to be superior to System I with a yield of 8 mM CH 3 OH, a TTN of 160 and BPR of 24 μmol CH 3 OH/U · h during 6 hr of reaction. The study demonstrates that an optimal reaction set-up could be designed from rational kinetics modeling to maximize the yield of CH 3 OH, whilst simultaneously optimizing cofactor recycling and enzyme utilization efficiency. © 2017 Wiley Periodicals, Inc.

THEORETICAL RESEARCH ON THE MULTI-CHANNEL REACTION MECHANISM AND KINETICS OF HNCS WITH OH-

Directory of Open Access Journals (Sweden)

Li-Jie Hou

Full Text Available We presented a theoretical study on the detailed reaction mechanism and kinetics of the HNCS molecule with the OH-. The barrierless minimum energy path and the most favorable entrance channel have been determined by study the thermodynamic and kinetic characters of the channel with low energy barrier. The B3LYP/6-311++G** method was employed for all the geometrical optimizations and a multi-level extrapolation method based on the G3 energies was employed for further energy refinements. In addition, the analysis of the combining interaction between hydroxide ion and HNCS was performed by natural bond orbitals (NBO analysis. The calculation results indicated that the reaction of OH- with HNCS had four channels, and the channel of H-atom in HNCS direct extraction to OH- (OH-+HNCS→IM1→TS3→IM4→P2(SCN- +H2O in singlet state was the main channel with the low potential energy and high equilibrium constant and reaction rate constant. SCN- and H2O were main products.

The role of high temperature heterogeneous reaction kinetics in the rate of radionuclide vaporisation during core-concrete interactions

International Nuclear Information System (INIS)

Raymond, D.P.; Clough, P.N.

1989-09-01

Heterogeneous reactions may cause enhanced release of radionuclides during the core-concrete interaction (CCl) stage of a PWR severe accident. The VANESA computer code models these CCI releases using chemical equilibrium assumptions; however, the possibility that chemical kinetics could prevent equilibrium from being achieved is considered in this report. Direct experimental evidence is lacking on these reactions. Therefore, some analogues studies are reviewed, including examples of Eyring's surface reaction rate theory; sequential vaporisation-oxidation processes; iron and steelmaking chemistry; radionuclide evaporation from solid UO 2 . This circumstantial evidence appeared to agree with the current assumptions, in VANESA and some UK modelling studies, that mass transfer, rather than chemical kinetics will limit the rate at which equilibrium is attained. (author)

Investigation of Coal-biomass Catalytic Gasification using Experiments, Reaction Kinetics and Computational Fluid Dynamics

Energy Technology Data Exchange (ETDEWEB)

Battaglia, Francine [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Agblevor, Foster [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Klein, Michael [Univ. of Delaware, Newark, DE (United States); Sheikhi, Reza [Northeastern Univ., Boston, MA (United States)

2015-12-31

A collaborative effort involving experiments, kinetic modeling, and computational fluid dynamics (CFD) was used to understand co-gasification of coal-biomass mixtures. The overall goal of the work was to determine the key reactive properties for coal-biomass mixed fuels. Sub-bituminous coal was mixed with biomass feedstocks to determine the fluidization and gasification characteristics of hybrid poplar wood, switchgrass and corn stover. It was found that corn stover and poplar wood were the best feedstocks to use with coal. The novel approach of this project was the use of a red mud catalyst to improve gasification and lower gasification temperatures. An important results was the reduction of agglomeration of the biomass using the catalyst. An outcome of this work was the characterization of the chemical kinetics and reaction mechanisms of the co-gasification fuels, and the development of a set of models that can be integrated into other modeling environments. The multiphase flow code, MFIX, was used to simulate and predict the hydrodynamics and co-gasification, and results were validated with the experiments. The reaction kinetics modeling was used to develop a smaller set of reactions for tractable CFD calculations that represented the experiments. Finally, an efficient tool was developed, MCHARS, and coupled with MFIX to efficiently simulate the complex reaction kinetics.

Reaction mechanisms and kinetics of the iminovinylidene radical with NO: Ab initio study

Energy Technology Data Exchange (ETDEWEB)

Hsiao, Ming-Kai; Chung, Yi-Hua; Hung, Yu-Ming; Chen, Hui-Lung, E-mail: chl3@faculty.pccu.edu.tw [Department of Chemistry and Institute of Applied Chemistry, Chinese Culture University, Taipei 111, Taiwan (China)

2014-05-28

The nitric oxide (NO) is a notorious compound for polluting environment. Recent year, removing nitric oxide from the atmosphere becomes a focus of the investigation. In our work, we study the iminovinylidene (HNCC) radical reacted with NO molecule. The mechanism and kinetic for reaction of the HNCC radical with the NO molecule is investigated via considering the possible channels of the N and O atoms of NO attacking the N and C atoms of the HNCC based on the high level ab initio molecular orbital calculations in conjunction with variational TST and RRKM calculations. The species involved have been optimized at the B3LYP/6-311++G(3df,2p) level and their single-point energies are refined by the CCSD(T)/aug-cc-PVQZ//B3LYP/6-311++G(3df,2p) method. The calculated potential energy surfaces indicated that energetically the most favorable channel for the HNCC + NO reaction was predicted to be the formation of HNC+CNO (P8) product via the addition reaction of the C atom of HNCC radical and the N atom of NO with the head to head orientation. To rationalize the scenario of the calculated results, we also employ the Fukui functions and HSAB theory to seek for a possible explanation. In addition, the reaction rate constants were calculated using VariFlex code, and the results show that the total rate coefficient, k{sub total}, at Ar pressure 760 Torr can be represented with an equation: k{sub total} = 6.433 × 10{sup −11} T {sup 0.100} exp(0.275 kcal mol{sup −1}/RT) at T = 298–3000 K, in units of cm{sup 3} molecule{sup −1} s{sup −1}.

Using ground reaction force to predict knee kinetic asymmetry following anterior cruciate ligament reconstruction.

Science.gov (United States)

Dai, B; Butler, R J; Garrett, W E; Queen, R M

2014-12-01

Asymmetries in sagittal plane knee kinetics have been identified as a risk factor for anterior cruciate ligament (ACL) re-injury. Clinical tools are needed to identify the asymmetries. This study examined the relationships between knee kinetic asymmetries and ground reaction force (GRF) asymmetries during athletic tasks in adolescent patients following ACL reconstruction (ACL-R). Kinematic and GRF data were collected during a stop-jump task and a side-cutting task for 23 patients. Asymmetry indices between the surgical and non-surgical limbs were calculated for GRF and knee kinetic variables. For the stop-jump task, knee kinetics asymmetry indices were correlated with all GRF asymmetry indices (P kinetic asymmetry indices were correlated with the peak propulsion vertical GRF and vertical GRF impulse asymmetry indices (P kinetic asymmetries and therefore may assist in optimizing rehabilitation outcomes and minimizing re-injury rates. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Nonequilibrium transition and pattern formation in a linear reaction-diffusion system with self-regulated kinetics

Science.gov (United States)

Paul, Shibashis; Ghosh, Shyamolina; Ray, Deb Shankar

2018-02-01

We consider a reaction-diffusion system with linear, stochastic activator-inhibitor kinetics where the time evolution of concentration of a species at any spatial location depends on the relative average concentration of its neighbors. This self-regulating nature of kinetics brings in spatial correlation between the activator and the inhibitor. An interplay of this correlation in kinetics and disparity of diffusivities of the two species leads to symmetry breaking non-equilibrium transition resulting in stationary pattern formation. The role of initial noise strength and the linear reaction terms has been analyzed for pattern selection.

Morphological impact on the reaction kinetics of size-selected cobalt oxide nanoparticles

International Nuclear Information System (INIS)

Bartling, Stephan; Meiwes-Broer, Karl-Heinz; Barke, Ingo; Pohl, Marga-Martina

2015-01-01

Apart from large surface areas, low activation energies are essential for efficient reactions, particularly in heterogeneous catalysis. Here, we show that not only the size of nanoparticles but also their detailed morphology can crucially affect reaction kinetics, as demonstrated for mass-selected, soft-landed, and oxidized cobalt clusters in a 6 nm to 18 nm size range. The method of reflection high-energy electron diffraction is extended to the quantitative determination of particle activation energies which is applied for repeated oxidation and reduction cycles at the same particles. We find unexpectedly small activation barriers for the reduction reaction of the largest particles studied, despite generally increasing barriers for growing sizes. We attribute these observations to the interplay of reaction-specific material transport with a size-dependent inner particle morphology

Reaction kinetics and modeling of photoinitiated cationic polymerization of an alicyclic based diglycidyl ether

International Nuclear Information System (INIS)

Harikrishna, R.; Ponrathnam, S.; Tambe, S.S.

2014-01-01

Highlights: • Photocationic polymerization of alicyclic based diglycidyl ether was carried out. • Kinetic parameters were influenced by gelation and diffusional restrictions. • Applicability of autocatalytic model was established by nonlinear regression. • System showed higher activation energy than cycloaliphatic and aromatic diepoxides. -- Abstract: Photoinitiated cationic polymerization of cycloaliphatic diepoxides had received tremendous attention, while studies with lesser polymerizable diglycidyl ethers are comparatively less reported. The present work deals with the photoinitiated cationic polymerization of cyclohexane dimethanol diglycidyl ether followed by estimation of kinetic parameters. The effects of concentration of photoinitiator and temperature on curing performance were studied using photo differential scanning calorimeter or photo DSC with polychromatic radiation. It was observed that the rate of polymerization as well as ultimate conversion increased with increasing concentration of photoinitiator and temperature. The influences of gelation as well as diffusional restrictions have remarkable effect on cure performance. The kinetic parameters as per autocatalytic kinetic model were studied by Levenberg–Marquardt nonlinear regression method instead of conventional linear method for obtaining more accurate values of apparent rate constant. It was observed that the model fits with data from initial stages to almost towards the end of the reaction. The activation energy was found to be higher than the values reported for more reactive cycloaliphatic diepoxides. The value of pre-exponential factor increased with increase in activation energy showing influence of gelation at early stages of reaction

Kinetic studies of the yeast His-Asp phosphorelay signaling pathway

Science.gov (United States)

Kaserer, Alla O.; Andi, Babak; Cook, Paul F.; West, Ann H.

2010-01-01

For both prokaryotic and eukaryotic His-Asp phosphorelay signaling pathways, the rates of protein phosphorylation and dephosphorylation determine the stimulus-to-response time frame. Thus, kinetic studies of phosphoryl group transfer between signaling partners are important for gaining a full understanding of how the system is regulated. In many cases, the phosphotransfer reactions are too fast for rates to be determined by manual experimentation. Rapid quench flow techniques thus provide a powerful method for studying rapid reactions that occur in the millisecond time frame. In this chapter, we describe experimental design and procedures for kinetic characterization of the yeast SLN1-YPD1-SSK1 osmoregulatory phosphorelay system using a rapid quench flow kinetic instrument. PMID:20946842

Reactions of plutonium and uranium with water: Kinetics and potential hazards

International Nuclear Information System (INIS)

Haschke, J.M.

1995-12-01

The chemistry and kinetics of reactions between water and the metals and hydrides of plutonium and uranium are described in an effort to consolidate information for assessing potential hazards associated with handling and storage. New experimental results and data from literature sources are presented. Kinetic dependencies on pH, salt concentration, temperature and other parameters are reviewed. Corrosion reactions of the metals in near-neutral solutions produce a fine hydridic powder plus hydrogen. The corrosion rate for plutonium in sea water is a thousand-fold faster than for the metal in distilled water and more than a thousand-fold faster than for uranium in sea water. Reaction rates for immersed hydrides of plutonium and uranium are comparable and slower than the corrosion rates for the respective metals. However, uranium trihydride is reported to react violently if a quantity greater than twenty-five grams is rapidly immersed in water. The possibility of a similar autothermic reaction for large quantities of plutonium hydride cannot be excluded. In addition to producing hydrogen, corrosion reactions convert the massive metals into material forms that are readily suspended in water and that are aerosolizable and potentially pyrophoric when dry. Potential hazards associated with criticality, environmental dispersal, spontaneous ignition and explosive gas mixtures are outlined

REACTION KINETICS SELF-PROPOGATION REGIME DURING PRE-IGNITION PERIOD

Directory of Open Access Journals (Sweden)

D. D. Polishchuk

2015-11-01

Full Text Available Self-propagation high temperature synthesis (SHS technological regulations application is mainly limited by transformation processes taking place in the pre-ignition period. Zn-S, Zn-Se, Ti-C and 3Ni-Al small sample systems ignition experimental study was carried out under heating conditions in inert atmosphere with temperature values T = 1200K.It was shown that at this temperature level a chemical reaction can be initiated, turning into a self-sustaining mode. Wherein the reaction limiting factors can be mass transfer processes. Ignition temperatures were determined and plotted via the samples size. A physical ignition model was developed assuming the pre-ignition period limiting reaction Arrhenius law.The inverse combustion problem solution made it possible to calculate the low-temperature (T = 800 ÷ 1200K reaction kinetic constant values. Comparison thus obtained values  with the known data of other researchers showed their good agreement.Activation energy values for the Zn-S system were used to calculate the heat wave propagation speed. This value appeared to coincide with experimental values.Obtained results analysis leads to the conclusion about the availability and justification for the proposed method of express-analysis of presupposed, but previously not studied SHS systems. The results thus obtained allow us to estimate conditions for the SHS technology implementation, the reactor characteristic sizes and the thermal wave’s propagation speed.

Kinetic and mechanism formation reaction of complex compound Cu with di-n-buthildithiocarbamate (dbdtc) ligand

Science.gov (United States)

Haryani, S.; Kurniawan, C.; Kasmui

2018-04-01

Synthesis of complex compound is one field of research which intensively studied. Metal-dithiocarbamate complexes find wide-ranging applications in nanomaterial and metal separation science, and have potential use as chemotherapeutic, pesticides, and as additives to lubricants. However, the information about is reaction kinetic and mechanism are very much lacking. The research and analyzes results show that reaction synthesis ligand DBDTC and complex compounds Cu-DBDTC. Optimum reaction condition of formation of complex compounds Cu with DBDTC at pH=3, [DBDTC] = 4.10-3 M, and the time of reaction 5 minutes. Based the analysis varian reaction of complex compounds at pH 3 and 4, diffrence significance at the other pH: 5; 5,5; 6; 6,5 ; 7; and 8. The various of mole with reactants comosition difference sigbificance, those the time reaction for 5 and 6 minutes diffrence by significance with the other time, it is 3,4,8, and 10 minutes. The great product to at condition pH 6, the time optimum at 5 minutes and molar ratio of logam: ligand = 1:2. The reaction kinetic equation of complex compound Cu with chelathing ligand DBDTC is V=0.917106 [Cu2+]0.87921 [DBDTC]2.03021. Based on the kinetic data, and formed complex compounds estimation, the mechanism explaining by 2 stages. In the first stage formation of [Cu(DBDTC)], and then [Cu(DBDTC)2] with the last structure geomethry planar rectangle. The result of this research will be more useful if an effort is being done in reaction mechanism by chemical computation method for obtain intermediate, and for constant “k” in same stage, k1.k2. and compound complex constanta (β).

Thermodynamic criteria for estimating the kinetic parameters of catalytic reactions

Science.gov (United States)

Mitrichev, I. I.; Zhensa, A. V.; Kol'tsova, E. M.

2017-01-01

Kinetic parameters are estimated using two criteria in addition to the traditional criterion that considers the consistency between experimental and modeled conversion data: thermodynamic consistency and the consistency with entropy production (i.e., the absolute rate of the change in entropy due to exchange with the environment is consistent with the rate of entropy production in the steady state). A special procedure is developed and executed on a computer to achieve the thermodynamic consistency of a set of kinetic parameters with respect to both the standard entropy of a reaction and the standard enthalpy of a reaction. A problem of multi-criterion optimization, reduced to a single-criterion problem by summing weighted values of the three criteria listed above, is solved. Using the reaction of NO reduction with CO on a platinum catalyst as an example, it is shown that the set of parameters proposed by D.B. Mantri and P. Aghalayam gives much worse agreement with experimental values than the set obtained on the basis of three criteria: the sum of the squares of deviations for conversion, the thermodynamic consistency, and the consistency with entropy production.

KEMOD: A mixed chemical kinetic and equilibrium model of aqueous and solid phase geochemical reactions

International Nuclear Information System (INIS)

Yeh, G.T.; Iskra, G.A.

1995-01-01

This report presents the development of a mixed chemical Kinetic and Equilibrium MODel in which every chemical species can be treated either as a equilibrium-controlled or as a kinetically controlled reaction. The reaction processes include aqueous complexation, adsorption/desorption, ion exchange, precipitation/dissolution, oxidation/reduction, and acid/base reactions. Further development and modification of KEMOD can be made in: (1) inclusion of species switching solution algorithms, (2) incorporation of the effect of temperature and pressure on equilibrium and rate constants, and (3) extension to high ionic strength

Kinetic study of ozonation of molasses fermentation wastewater

International Nuclear Information System (INIS)

Coca, M.; Pena, M.; Gonzalez, G.

2007-01-01

A kinetic study of molasses wastewater ozonation was carried out in a stirred tank reactor to obtain the rate constants for the decolorization reaction and the regime through which ozone is absorbed. First, fundamental mass transfer parameters such as ozone solubility, volumetric mass transfer coefficients and ozone decomposition kinetics were determined from semi-batch experiments in organic-free solutions with an ionic composition similar that of industrial wastewater. The influence of operating variables such as the stirring rate and gas flow rate on the kinetic and mass transfer parameters was also studied. The application of film theory allows to establish that the reactions between ozone and colored compounds in wastewater take place in the fast and pseudo-first-order regime, within the liquid film. The decolorization rate constants were evaluated at pH 8.7 and 25 deg. C, varying from 0.6 x 10 7 to 3.8 x 10 7 L mol -1 s -1 , depending on the stirring rate and the inlet gas flow

Preclusion of switch behavior in reaction networks with mass-action kinetics

DEFF Research Database (Denmark)

Feliu, Elisenda; Wiuf, C.

2012-01-01

We study networks taken with mass-action kinetics and provide a Jacobian criterion that applies to an arbitrary network to preclude the existence of multiple positive steady states within any stoichiometric class for any choice of rate constants. We are concerned with the characterization...... precludes the existence of degenerate steady states. Further, we relate injectivity of a network to that of the network obtained by adding outflow, or degradation, reactions for all species....

Kinetic catalytic studies of scorpion's hemocyanin

International Nuclear Information System (INIS)

Queinnec, E.; Vuillaume, M.; Gardes-Albert, M.; Ferradini, C.; Ducancel, F.

1991-01-01

Hemocyanins are copper proteins which function as oxygen carriers in the haemolymph of Molluscs and Arthropods. They possess enzymatic properties: peroxidatic and catalatic activities, although they have neither iron nor porphyrin ring at the active site. The kinetics of the catalytic reaction is described. The reaction of superoxide anion with hemocyanin has been studied using pulse radiolysis at pH 9. The catalytic rate constant is 3.5 X 10 7 mol -1 .l.s -1 [fr

Kinetic and thermodynamic studies of reactional system (X-I-O-H) by high temperature mass spectrometry

International Nuclear Information System (INIS)

Roki, F.Z.

2009-01-01

High temperature mass spectrometry is used for analysis of vapors coming from iodine reaction with fission products in case of a severe nuclear accident in a pressurized water reactor. Two main ways are used, - (i) thermodynamic analysis of vaporization processes of CsOH, CsI and mixtures CsI-CsOH. - (ii) building a dedicated reactor for kinetic analysis of the recombination of atoms into these stables molecular species. The present study confirms the existence of Cs 2 IOH(g) molecule. Vapor pressures of gaseous molecules CsOH(g), Cs 2 O 2 H 2 (g) and Cs 2 IOH(g) have been determined. Molecular parameters of the mixed molecule have been estimated on the basis of the pure dimmers Cs 2 O 2 H 2 (g) and Cs 2 I 2 (g) and its enthalpy of formation are established. The acquisition of kinetic data needs a new reactor, the conception of which is presented in this work as well as qualification tests: thermal, flow regimes and pressure calibration tests. (author)

Kinetics of ethylcyclohexane pyrolysis and oxidation: An experimental and detailed kinetic modeling study

KAUST Repository

Wang, Zhandong

2015-07-01

Ethylcyclohexane (ECH) is a model compound for cycloalkanes with long alkyl side-chains. A preliminary investigation on ECH (Wang et al., Proc. Combust. Inst., 35, 2015, 367-375) revealed that an accurate ECH kinetic model with detailed fuel consumption mechanism and aromatic growth pathways, as well as additional ECH pyrolysis and oxidation data with detailed species concentration covering a wide pressure and temperature range are required to understand the ECH combustion kinetics. In this work, the flow reactor pyrolysis of ECH at various pressures (30, 150 and 760Torr) was studied using synchrotron vacuum ultraviolet (VUV) photoionization mass spectrometry (PIMS) and gas chromatography (GC). The mole fraction profiles of numerous major and minor species were evaluated, and good agreement was observed between the PIMS and GC data sets. Furthermore, a fuel-rich burner-stabilized laminar premixed ECH/O2/Ar flame at 30Torr was studied using synchrotron VUV PIMS. A detailed kinetic model for ECH high temperature pyrolysis and oxidation was developed and validated against the pyrolysis and flame data performed in this work. Further validation of the kinetic model is presented against literature data including species concentrations in jet-stirred reactor oxidation, ignition delay times in a shock tube, and laminar flame speeds at various pressures and equivalence ratios. The model well predicts the consumption of ECH, the growth of aromatics, and the global combustion properties. Reaction flux and sensitivity analysis were utilized to elucidate chemical kinetic features of ECH combustion under various reaction conditions. © 2015 The Combustion Institute.

Reaction kinetics in open reactors and serial transfers between closed reactors

Science.gov (United States)

Blokhuis, Alex; Lacoste, David; Gaspard, Pierre

2018-04-01

Kinetic theory and thermodynamics of reaction networks are extended to the out-of-equilibrium dynamics of continuous-flow stirred tank reactors (CSTR) and serial transfers. On the basis of their stoichiometry matrix, the conservation laws and the cycles of the network are determined for both dynamics. It is shown that the CSTR and serial transfer dynamics are equivalent in the limit where the time interval between the transfers tends to zero proportionally to the ratio of the fractions of fresh to transferred solutions. These results are illustrated with a finite cross-catalytic reaction network and an infinite reaction network describing mass exchange between polymers. Serial transfer dynamics is typically used in molecular evolution experiments in the context of research on the origins of life. The present study is shedding a new light on the role played by serial transfer parameters in these experiments.

Studies on adsorption, reaction mechanisms and kinetics for photocatalytic degradation of CHD, a pharmaceutical waste.

Science.gov (United States)

Sarkar, Santanu; Bhattacharjee, Chiranjib; Curcio, Stefano

2015-11-01

The photocatalytic degradation of chlorhexidine digluconate (CHD), a disinfectant and topical antiseptic and adsorption of CHD catalyst surface in dark condition has been studied. Moreover, the value of kinetic parameters has been measured and the effect of adsorption on photocatalysis has been investigated here. Substantial removal was observed during the photocatalysis process, whereas 40% removal was possible through the adsorption route on TiO2 surface. The parametric variation has shown that alkaline pH, ambient temperature, low initial substrate concentration, high TiO2 loading were favourable, though at a certain concentration of TiO2 loading, photocatalytic degradation efficiency was found to be maximum. The adsorption study has shown good confirmation with Langmuir isotherm and during the reaction at initial stage, it followed pseudo-first-order reaction, after that Langmuir Hinshelwood model was found to be appropriate in describing the system. The present study also confirmed that there is a significant effect of adsorption on photocatalytic degradation. The possible mechanism for adsorption and photocatalysis has been shown here and process controlling step has been identified. The influences of pH and temperature have been explained with the help of surface charge distribution of reacting particles and thermodynamic point of view respectively. Copyright © 2015 Elsevier Inc. All rights reserved.

Kinetics study of heterogeneous reactions of ozone with erucic acid using an ATR-IR flow reactor.

Science.gov (United States)

Leng, Chunbo; Hiltner, Joseph; Pham, Hai; Kelley, Judas; Mach, Mindy; Zhang, Yunhong; Liu, Yong

2014-03-07

The ozone initiated heterogeneous oxidation of erucic acid (EA) thin film was investigated using a flow system combined with attenuated total reflection infrared spectroscopy (ATR-IR) over wide ranges of ozone concentrations (0.25-60 ppm), thin film thickness (0.1-1.0 μm), temperatures (263-298 K), and relative humidities (0-80% RH) for the first time. Pseudo-first-order rate constants, kapp, and overall reactive uptake coefficients, γ, were obtained through changes in the absorbance of C[double bond, length as m-dash]O stretching bands at 1695 cm(-1), which is assigned to the carbonyl group in carboxylic acid. Results showed that the reaction followed the Langmuir-Hinshelwood mechanism and kapp was largely dominated by surface reaction over bulk phase reaction. In addition, both the kapp and the γ values showed very strong temperature dependences (∼two orders of magnitude) over the temperature range; in contrast, they only slightly increased with increasing RH values from 0-80%. According to the kapp values as a function of temperature, the activation energy for the heterogeneous reaction was estimated to be 80.6 kJ mol(-1). Our results have suggested that heterogeneous reactions between ozone and unsaturated solid surfaces likely have a substantially greater temperature dependence than liquid ones. Moreover, the hygroscopic properties of EA thin films before and after exposure to ozone were also studied by measurement of water uptake. Based on the hygroscopicity data, the insignificant RH effect on reaction kinetics was probably due to the relatively weak water uptake by the unreacted and reacted EA thin films.

Variable elimination in chemical reaction networks with mass-action kinetics

DEFF Research Database (Denmark)

Feliu, Elisenda; Wiuf, C.

2012-01-01

We consider chemical reaction networks taken with mass-action kinetics. The steady states of such a system are solutions to a system of polynomial equations. Even for small systems the task of finding the solutions is daunting. We develop an algebraic framework and procedure for linear elimination...

Cholesterol photo-oxidation: A chemical reaction network for kinetic modeling.

Science.gov (United States)

Barnaba, Carlo; Rodríguez-Estrada, Maria Teresa; Lercker, Giovanni; García, Hugo Sergio; Medina-Meza, Ilce Gabriela

2016-12-01

In this work we studied the effect of polyunsaturated fatty acids (PUFAs) methyl esters on cholesterol photo-induced oxidation. The oxidative routes were modeled with a chemical reaction network (CRN), which represents the first application of CRN to the oxidative degradation of a food-related lipid matrix. Docosahexaenoic acid (DHA, T-I), eicosapentaenoic acid (EPA, T-II) and a mixture of both (T-III) were added to cholesterol using hematoporphyrin as sensitizer, and were exposed to a fluorescent lamp for 48h. High amounts of Type I cholesterol oxidation products (COPs) were recovered (epimers 7α- and 7β-OH, 7-keto and 25-OH), as well as 5β,6β-epoxy. Fitting the experimental data with the CRN allowed characterizing the associated kinetics. DHA and EPA exerted different effects on the oxidative process. DHA showed a protective effect to 7-hydroxy derivatives, whereas EPA enhanced side-chain oxidation and 7β-OH kinetic rates. The mixture of PUFAs increased the kinetic rates several fold, particularly for 25-OH. With respect to the control, the formation of β-epoxy was reduced, suggesting potential inhibition in the presence of PUFAs. Copyright © 2016 Elsevier Inc. All rights reserved.

Kinetics of the reactions of hydrated electrons with metal complexes

International Nuclear Information System (INIS)

Korsse, J.

1983-01-01

The reactivity of the hydrated electron towards metal complexes is considered. Experiments are described involving metal EDTA and similar complexes. The metal ions studied are mainly Ni 2+ , Co 2+ and Cu 2+ . Rates of the reactions of the complexes with e - (aq) were measured using the pulse radiolysis technique. It is shown that the reactions of e - (aq) with the copper complexes display unusually small kinetic salt effects. The results suggest long-range electron transfer by tunneling. A tunneling model is presented and the experimental results are discussed in terms of this model. Results of approximate molecular orbital calculations of some redox potentials are given, for EDTA chelates as well as for series of hexacyano and hexaquo complexes. Finally, equilibrium constants for the formation of ternary complexes are reported. (Auth./G.J.P.)

Flow-Based Systems for Rapid and High-Precision Enzyme Kinetics Studies

Directory of Open Access Journals (Sweden)

Supaporn Kradtap Hartwell

2012-01-01

Full Text Available Enzyme kinetics studies normally focus on the initial rate of enzymatic reaction. However, the manual operation of steps of the conventional enzyme kinetics method has some drawbacks. Errors can result from the imprecise time control and time necessary for manual changing the reaction cuvettes into and out of the detector. By using the automatic flow-based analytical systems, enzyme kinetics studies can be carried out at real-time initial rate avoiding the potential errors inherent in manual operation. Flow-based systems have been developed to provide rapid, low-volume, and high-precision analyses that effectively replace the many tedious and high volume requirements of conventional wet chemistry analyses. This article presents various arrangements of flow-based techniques and their potential use in future enzyme kinetics applications.

Kinetic modelling of hydro-treatment reactions by study of different chemical groups; Modelisation cinetique des reactions d`hydrotraitement par regroupement en familles chimiques

Energy Technology Data Exchange (ETDEWEB)

Bonnardot, J

1998-11-19

Hydro-treatment of petroleum shortcuts permits elimination of unwanted components in order to increase combustion in engine and to decrease atmospheric pollution. Hydro-desulfurization (HDS), Hydro-denitrogenation (HDN) and Hydrogenation of aromatics (HDA) of a LCO (Light Cycle Oil)-Type gas oil have been studied using a new pilot at a fixed temperature with a NiMo/Al{sub 2}O{sub 3} catalyst. A hydrodynamic study showed that reactions occurring in the up-flow fixed bed reactor that has been used during the experiments, were governed exclusively by chemical reaction rates and not by diffusion. Through detailed chemical analysis, height chemical groups have been considered: three aromatics groups, one sulfided group, one nitrogenized and NH{sub 3}, H{sub 2}S, H{sub 2}. Two Langmuir-Hinshelwood-type kinetic models with either one or two types of sites have been established. The model with two types of site - one site of hydrogenation and one site of hydrogenolysis - showed a better fit in the modeling of the experimental results. This model enables to forecast the influence of partial pressure of H{sub 2}S and partial pressure of H{sub 2} on hydro-treatment reactions of a LCO-type gas oil. (author) 119 refs.

Kinetics based reaction optimization of enzyme catalysed reduction of formaldehyde to methanol with synchronous cofactor regeneration

DEFF Research Database (Denmark)

Marpani, Fauziah Binti; Sárossy, Zsuzsa; Pinelo, Manuel

2017-01-01

regeneration of the reducing equivalents during reaction is required. Herein, we report the optimization of the enzymatic conversion of formaldehyde (CHOH) to CH3 OH by alcohol dehydrogenase, the final step of the enzymatic redox reaction of CO2 to CH3 OH, with kinetically synchronous enzymatic cofactor...... regeneration using either glucose dehydrogenase (System I) or xylose dehydrogenase (System II). A mathematical model of the enzyme kinetics was employed to identify the best reaction set-up for attaining optimal cofactor recycling rate and enzyme utilization efficiency. Targeted process optimization...... experiments were conducted to verify the kinetically modelled results. Repetitive reaction cycles were shown to enhance the yield of CH3 OH, increase the total turnover number (TTN) and the biocatalytic productivity rate (BPR) value for both system I and II whilst minimizing the exposure of the enzymes...

Reaction network modelling for kinetic parameters of pyrolytic reactions of CHON extractants in nuclear fuel processing waste management. Contributed Paper IT-07

International Nuclear Information System (INIS)

Gaikar, Vilas G.; Thaore, Vaishali

2014-01-01

The recovery and purification of plutonium (Pu) from uranium (U) and of U from Thorium (Th) in spent nuclear fuel reprocessing is accomplished by processes that employ organophosphorous compounds as extractants.The main objective of the present work was to develop a suitable kinetic model and to determine the kinetic parameters of the set of reactions involved in the pyrolysis of amides by fitting the experimental data in the reaction network model. The experimental data and analysis are expected to be useful in the steam pyrolysis of amide waste in fuel reprocessing in the nuclear industry. The basic approach was to understand the reaction mechanism of the steam pyrolysis of amides and then to estimate the reaction rate constants for the generation and consumption of different species by solving the model equations, allowing for the determination of important species in the reaction network

A study of redox kinetic in silicate melt

International Nuclear Information System (INIS)

Magnien, V.

2005-12-01

The aim of this thesis is to understand better iron redox reactions and mechanisms in silicate glasses and melts. Particular interest has been paid to the influence of temperature and chemical composition. For this purpose, the influence of alkali element content, iron content and network formers on the kinetics of redox reactions has been determined through XANES and Raman spectroscopy experiments performed either near the glass transition or above the liquidus temperature. As a complement, electrical conductivity and RBS spectroscopy experiments have been made to characterize the diffusivity of the species that transport electrical charges and the reaction morphology, respectively. Temperature and composition variations can induce changes in the dominating redox mechanism. At a given temperature, the parameters that exert the strongest influence on redox mechanisms are the presence or lack of divalent cations and the existing decoupling between the mobility of network former and modifier elements. Near Tg, the diffusion of divalent cations, when present in the melt, controls the kinetics of iron redox reactions along with a flux of electron holes. Composition, through the degree of polymerization and the silicate network structure, influences the kinetics and the nature of the involved cations, but not the mechanisms of the reaction. Without alkaline earth elements, the kinetics of redox reactions are controlled by the diffusion of oxygen species. With increasing temperatures, the diffusivities of all ionic species tend to become similar. The decoupling between ionic fluxes then is reduced so that several mechanisms become kinetically equivalent and can thus coexist. (author)

Kinetics of barium sulphate reaction crystallization in crystallizers with internal circulation

Directory of Open Access Journals (Sweden)

J. Koralewska

2008-06-01

Full Text Available Kinetic calculation results describing the observed nucleation and growth rates of barium sulphate crystals precipitated in an integrated reaction-crystallization process in a barium sulphate-ammonium chloride-water system are presented and analyzed. The scope of experiments included two continuous model DTM-type crystallizers (Draft Tube Magma with internal circulation of the suspension forced by a liquid jet-pump device responsible for stable and intensive enough ascending/descending flow of BaSO4 crystal magma in a mixing chamber. For comparison purposes the experimental data corresponding to a continuous DT (Draft Tube crystallizer with propeller agitator are presented and discussed. The various types of laboratory crystallizers used were fed with concentrated water solution of barium chloride (of 10 or 24 mass % and - in a stoichiometric proportion - crystalline ammonium sulphate, assuming isothermal (348 K and hydrodynamic (average residence time of suspension in a crystallizer: 900 s process conditions. The observed nucleation and growth rates of barium sulphate crystals were estimated on the basis of crystal size distributions (CSDs using convenient calculation scheme derived for an MSMPR (Mixed Suspension Mixed Product Removal model approach. Considering the experimental population density distribution courses, a size-dependent growth (SDG phenomenon was taken into account in the kinetic calculations. Five SDG kinetic models recommended in the accessible literature were used for kinetic parameter values estimation. It was proved statistically, that Rojkowski’s two SDG models (hyperbolic and exponential best suit for our own experimental data description. The experimental data presented can be practically applied for improving the constructions of liquid jet-pump DTM crystallizers recommended for reaction crystallization of sparingly soluble inorganic salts (especially for high concentrations of reaction substrates in the modern

Kinetics of the F+NO2+M->FNO2+M reaction studied by pulse radiolysis combined with time-resolved IR and UV spectroscopy

DEFF Research Database (Denmark)

Pagsberg, Palle Bjørn; Sillesen, A.; Jodkowski, J.T.

1996-01-01

was studied with SF6 pressures of 5-1000 mbar at 298 K. Comparative studies were carried out by monitoring the decay kinetics of NO2 at 445 nm using pressures of 100-1000 mbar at 295 and 341 K. The observed pressure dependence is represented in terms of a fall-off curve with the following values......The title reaction was initiated by the pulse radiolysis of SF6/NO2 gas mixtures, and the formation of FNO2 was studied by time-resolved infrared spectroscopy employing strong rotational transitions within the nu(1) and nu(4) bands of FNO2. The pressure dependence of the formation kinetics...

Kinetic studies on the hafnium nad deuterium

International Nuclear Information System (INIS)

Bing Wenzeng; Long Xinggui; Zhu Zuliang

2009-04-01

Through the method of reaction rate analysis in a constant volume reactor, the time dependence of the pressure drop of the hafnium deuteride formation are studied over a temperature range 573-873 K on a metal hydride thermodynamic and kinetic parameters measuring apparatus. The rate constants of the hafnium deuteride formation, which are 0.0530 s -1 , 0.0452 s -1 , 0.0319 s -1 , 0.0261 s -1 , are calculated at a serial temperatures of 573 K, 673 K, 773 K, 873 K and the initial pressure of 13 kPa. The activation energy of the reaction is (-10.1±1.5) kJ·mol -1 . Comparing the above results with those of titanium deuteride formation on the same measuring apparatus, the kinetic mechanism of the deuteride formation of hafnium and titanium is considered different. It is concluded that the reaction rate of hafnium absorbing deuterium may be controlled by phase transformation and surface oxidation. (authors)

Synthesis Of Magnesium-Aluminum Layered Double Hydroxides By Mechanochemical Method And Its Solid State Reaction Kinetics

Directory of Open Access Journals (Sweden)

Hongbo Y.

2015-06-01

Full Text Available A mechanochemical method is developed in preparing magnesium-aluminum-layered double hydroxides (MgAl-LDHs. This approach includes activation process and diffusion process. In order to verify the LDHs structure and study the reaction kinetics, X-ray diffraction (XRD patterns, inductively coupled plasma(ICP and physical adsorption instrument were characterized. The results show that activation time can change the surface of particles and affect the reaction grade. During the diffusion process, reaction time is the most important factor. The reaction energy (ΔQ was calculated that is 6kJ/mol.

Learning the Fundamentals of Kinetics and Reaction Engineering with the Catalytic Oxidation of Methane

Science.gov (United States)

Cybulskis, Viktor J.; Smeltz, Andrew D.; Zvinevich, Yury; Gounder, Rajamani; Delgass, W. Nicholas; Ribeiro, Fabio H.

2016-01-01

Understanding catalytic chemistry, collecting and interpreting kinetic data, and operating chemical reactors are critical skills for chemical engineers. This laboratory experiment provides students with a hands-on supplement to a course in chemical kinetics and reaction engineering. The oxidation of methane with a palladium catalyst supported on…

Kinetic Studies on Enzyme-Catalyzed Reactions: Oxidation of Glucose, Decomposition of Hydrogen Peroxide and Their Combination

Science.gov (United States)

Tao, Zhimin; Raffel, Ryan A.; Souid, Abdul-Kader; Goodisman, Jerry

2009-01-01

The kinetics of the glucose oxidase-catalyzed reaction of glucose with O2, which produces gluconic acid and hydrogen peroxide, and the catalase-assisted breakdown of hydrogen peroxide to generate oxygen, have been measured via the rate of O2 depletion or production. The O2 concentrations in air-saturated phosphate-buffered salt solutions were monitored by measuring the decay of phosphorescence from a Pd phosphor in solution; the decay rate was obtained by fitting the tail of the phosphorescence intensity profile to an exponential. For glucose oxidation in the presence of glucose oxidase, the rate constant determined for the rate-limiting step was k = (3.0 ± 0.7) ×104 M−1s−1 at 37°C. For catalase-catalyzed H2O2 breakdown, the reaction order in [H2O2] was somewhat greater than unity at 37°C and well above unity at 25°C, suggesting different temperature dependences of the rate constants for various steps in the reaction. The two reactions were combined in a single experiment: addition of glucose oxidase to glucose-rich cell-free media caused a rapid drop in [O2], and subsequent addition of catalase caused [O2] to rise and then decrease to zero. The best fit of [O2] to a kinetic model is obtained with the rate constants for glucose oxidation and peroxide decomposition equal to 0.116 s−1 and 0.090 s−1 respectively. Cellular respiration in the presence of glucose was found to be three times as rapid as that in glucose-deprived cells. Added NaCN inhibited O2 consumption completely, confirming that oxidation occurred in the cellular mitochondrial respiratory chain. PMID:19348778

Kinetic Study of the Aroxyl-Radical-Scavenging Activity of Five Fatty Acid Esters and Six Carotenoids in Toluene Solution: Structure-Activity Relationship for the Hydrogen Abstraction Reaction.

Science.gov (United States)

Mukai, Kazuo; Yoshimoto, Maya; Ishikura, Masaharu; Nagaoka, Shin-Ichi

2017-08-17

A kinetic study of the reaction between an aroxyl radical (ArO • ) and fatty acid esters (LHs 1-5, ethyl stearate 1, ethyl oleate 2, ethyl linoleate 3, ethyl linolenate 4, and ethyl arachidonate 5) has been undertaken. The second-order rate constants (k s ) for the reaction of ArO • with LHs 1-5 in toluene at 25.0 °C have been determined spectrophotometrically. The k s values obtained increased in the order of LH 1 LHs 1-5. The k s value for LH 5 was 2.93 × 10 -3 M -1 s -1 . From the result, it has been clarified that the reaction of ArO • with LHs 1-5 was explained by an allylic hydrogen abstraction reaction. A similar kinetic study was performed for the reaction of ArO • with six carotenoids (Car-Hs 1-6, astaxanthin 1, β-carotene 2, lycopene 3, capsanthin 4, zeaxanthin 5, and lutein 6). The k s values obtained increased in the order of Car-H 1 LHs 1-5. The results of detailed analyses of the k s values for the above reaction indicated that the reaction was also explained by an allylic hydrogen abstraction reaction. Furthermore, the structure-activity relationship for the reaction was discussed by taking the result of density functional theory calculation reported by Martinez and Barbosa into account.

Kinetics of the monomer-dimer reaction of yeast hexokinase PI.

Science.gov (United States)

Hoggett, J G; Kellett, G L

1992-10-15

Kinetic studies of the glucose-dependent monomer-dimer reaction of yeast hexokinase PI at pH 8.0 in the presence of 0.1 M-KCl have been carried out using the fluorescence temperature-jump technique. A slow-relaxation effect was observed which was attributed from its dependence on enzyme concentration to the monomer-dimer reaction; the reciprocal relaxation times tau-1 varied from 3 s-1 at low concentrations of glucose to 42 s-1 at saturating concentrations. Rate constants for association (kass.) and dissociation (kdiss.) were determined as a function of glucose concentration using values of the equilibrium association constant of the monomer-dimer reaction derived from sedimentation ultracentrifugation studies under similar conditions, and also from the dependence of tau-2 on enzyme concentration. kass. was almost independent of glucose concentration and its value (2 x 10(5) M-1.s-1) was close to that expected for a diffusion-controlled process. The influence of glucose on the monomer-dimer reaction is entirely due to effects on kdiss., which increases from 0.21 s-1 in the absence of glucose to 25 s-1 at saturating concentrations. The monomer and dimer forms of hexokinase have different affinities and Km values for glucose, and the results reported here imply that there may be a significant lag in the response of the monomer-dimer reaction to changes in glucose concentrations in vivo with consequent hysteretic effects on the hexokinase activity.

Studies of U(4) oxidation kinetics in nitric acid and TBP phases

International Nuclear Information System (INIS)

Taylor, R.J.; Denniss, I.S.; Koltunov, V.S.; Marchenko, V.I.; Dvoeglazov, K.N.; Savilova, O.A.; Broan, C.J.

2000-01-01

U(IV) is an important reagent in current reprocessing plants since it is used to reduce Pu(IV) to Pu(III), therefore, allowing the efficient separation of U and Pu in multi-stage counter-current solvent extraction contactors. The benefits of U(IV) are that it is a kinetically fast reductant and it is a salt free reagent, since U(IV) is oxidised to U(VI) and so does not add to the aqueous waste volumes. Many kinetic reactions of U(IV) have been studied in the past and these are used by BNFL to model the behaviour of U(IV) in process flowsheets. However, some reactions have either not been studied or have been studied many times without conclusive resolution. Therefore, to expand our understanding of U(IV) in the process and to generate data that underpins process models, we are studying a series of U(IV) reactions, and this paper will summarize the results of our kinetic and mechanistic studies. (authors)

Modelling and experimental evaluation of reaction kinetics in reactive extraction for chiral separation of amines, amino acids and amino-alcohols

NARCIS (Netherlands)

Steensma, M.; Kuipers, N.J.M.; de Haan, A.B.; Kwant, Gerard

2007-01-01

This paper reports on determination of the intrinsic reaction kinetics in reactive extraction of chiral compounds. It is important to know the mass transfer rates and reaction kinetics separately for a reliable scale-up. A kinetic model is developed to interpret the experimental data from the

Atmospheric chemistry of HFC-134a. Kinetic and mechanistic study of the CF3CFHO2 + NO2 reaction

DEFF Research Database (Denmark)

Møgelberg, T.E.; Nielsen, O.J.; Sehested, J.

1994-01-01

A pulse radiolysis system was used to study the kinetics of the reaction of CF3CFHO2 with NO2. By monitoring the rate of the decay of NO2 using its absorption at 400 nm the reaction rate constant was determined to be k = (5.0 +/- 0.5) x 10(-12) cm3 molecule-1 s-1. A long path length Fourier......-transform infrared technique was used to investigate the thermal decomposition of the product CF3CFHO2NO2. At 296 K in the presence of 700 Torr of air, decomposition of CF3CFHO2NO2 was rapid (greater than 90% decomposition within 3 min). The results are discussed in the context of atmospheric chemistry of CF3CFH2...

Searching out the hydrogen absorption/desorption limiting reaction factors: Strategies allowing to increase kinetics

Energy Technology Data Exchange (ETDEWEB)

Zeaiter, Ali, E-mail: ali.zeaiter@femto-st.fr; Chapelle, David; Nardin, Philippe

2015-10-05

Highlights: • A macro scale thermodynamic model that simulates the response of a FeTi-X hydride tank is performed, and validated experimentally. • A sensibility study to identify the most influent input variables that can changes very largely the reaction rate. - Abstract: Hydrogen gas has become one of the most promising energy carriers. Main breakthrough concerns hydrogen solid storage, specially based on intermetallic material use. Regarding the raw material abundance and cost, the AB type alloy FeTi is an auspicious candidate to store hydrogen. Its absorption/desorption kinetics is a basic hindrance to common use, compared with more usual hydrides. First, discussions based on literature help us identifying the successive steps leading to metal hydriding, and allow to introduce the physical parameters which drive or limit the reaction. This analysis leads us to suggest strategies in order to increase absorption/desorption kinetics. Attention is then paid to a thermofluidodynamic model, allowing to describe a macroscopic solid storage reactor. Thus, we can achieve a simulation which describes the overall reaction inside the hydrogen reactor and, by varying the sub-mentioned parameters (thermal conductivity, the powder granularity, environment heat exchange…), we attempt to hierarchy the reaction limiting factors. These simulations are correlated to absorption/desorption experiments for which pressure, temperature and hydrogen flow are recorded.

Kinetic study of UV-irradiated amorphous sulfur by EPR spectroscopy

International Nuclear Information System (INIS)

El Mkami, H.; Smith, G.M.

2005-01-01

Electron paramagnetic resonance (EPR) spectroscopy is used to investigate UV-irradiation damage in amorphous sulfur by examining post-irradiation kinetics as a function of UV-exposure time. The kinetic study is described by first-order concurrent reactions where the sulfur, as reactant, undergoes two parallel processes leading to the formation of two distinct defects called S 1 * and S 2 *. The temperature dependence of the EPR intensities of the signals, related to these defects, is used in the kinetic study

Hydrolysis of Surfactants Containing Ester Bonds: Modulation of Reaction Kinetics and Important Aspects of Surfactant Self-Assembly

Science.gov (United States)

Lundberg, Dan; Stjerndahl, Maria

2011-01-01

The effects of self-assembly on the hydrolysis kinetics of surfactants that contain ester bonds are discussed. A number of examples on how reaction rates and apparent reaction orders can be modulated by changes in the conditions, including an instance of apparent zero-order kinetics, are presented. Furthermore, it is shown that the examples on…

Thermogravimetric kinetic study of agricultural residue biomass pyrolysis based on combined kinetics.

Science.gov (United States)

Wang, Xun; Hu, Mian; Hu, Wanyong; Chen, Zhihua; Liu, Shiming; Hu, Zhiquan; Xiao, Bo

2016-11-01

Pyrolytic kinetic of an agricultural residue (AR) feedstock, a mixture of plants (cotton, wheat, rich, corn) stems, was investigated based on combined kinetics. The most suitable mechanism for AR one-step pyrolysis was f(α)=(1-α)(1.1816)α(-1.8428) with kinetic parameters of: apparent activation energy 221.7kJ/mol, pre-exponential factor 4.17E16s(-1). Pyrolysis of AR feedstock could not be described by one-step reaction attributes to heterogeneous features of pyrolysis processes. Combined kinetics three-parallel-reaction (CK-TPR) model fitted the pyrolysis experimental data very well. Reaction mechanisms for pseudo hemicelluloses, cellulose, lignin in CK-TPR model was f(α)=(1-α)(1.6244)α(-0.3371)[-ln(1-α)](-0.0515), f(α)=(1-α)(1.0597)α(-0.6909)[-ln(1-α)](0.9026) and f(α)=(1-α)(2.9577)α(-4.7719), respectively. Apparent activation energy of three pseudo components followed the order of Elignin(197.3kJ/mol)>Ecellulose(176.3kJ/mol)>Ehemicelluloses (151.1kJ/mol). Mechanism of hemicelluloses pyrolysis could be further expressed as f(α)=(1-α)(1.4). The pyrolytic mechanism of cellulose met the Nucleation well. However, mechanism of lignin pyrolysis was complex, which possibly was the combined effects of Nucleation, Diffusion, Geometrical contraction, and Power law. Copyright © 2016 Elsevier Ltd. All rights reserved.

Kinetics of the reaction of CH3O2 radicals with NO2

DEFF Research Database (Denmark)

Wallington, T.J.; Nielsen, O.J.; Sehested, K.

1999-01-01

The kinetics of the gas-phase reaction of CH3O2 radicals with NO2 were studied at 295 K in 0.5-14 arm of SF6 diluent using pulse radiolysis combined with time-resolved UV-VIS spectroscopy. Rate data were obtained by following the loss of CH3O2 using a monitoring wavelength of 260 nm. The results...

Experimental kinetic study and modeling of calcium oxide carbonation

International Nuclear Information System (INIS)

Rouchon, L.

2012-01-01

Anthropogenic carbon dioxide (CO 2 ) emissions, major contributors to the greenhouse effect, are considered as the main cause of global warming. So, decrease of CO 2 emitted by large industrial combustion sources or power plants, is an important scientific goal. One of the approaches is based on CO 2 separation and capture from flue gas, followed by sequestration in a wide range of geological formations. In this aim, CO 2 is captured by sorbents like calcium oxide (CaO) in multi-cycle process of carbonation/de-carbonation. However, it was shown that the most important limitations of such process are related to the reversibility of reaction. CaO rapidly loses activity towards CO 2 , so the maximum extent of carbonation decreases as long as the number of cycles increases. In order to well understand the processes and parameters influencing the capture capacity of CaO-based sorbents, it appears important to get details on the kinetic law governing the reaction, which have not been really studied up to now. To investigate this reaction, CaO carbonation kinetics was followed by means of thermogravimetric analysis (TGA) on divided materials. Special care was given to the validation of the usual kinetic assumptions such as steady state and rate-determining step assumptions. The aim was to obtain a model describing the reaction in order to explain the influence of intensive variables such as carbonation temperature and CO 2 partial pressure. TGA curves obtained under isothermal and isobaric conditions showed an induction period linked to the nucleation process and a strong slowing down of the reaction rate once a given fractional conversion was reached. Both phenomena were observed to depend on carbonation temperature and CO 2 partial pressure. To explain these results, the evolution of texture and microstructure of the solid during the reaction was regarded as essential. Reaction at the grain scale induces a volume increase from CaO to CaCO 3 which causes a change in the

On the ultrafast kinetics of the energy and electron transfer reactions in photosystem I

Energy Technology Data Exchange (ETDEWEB)

Slavov, Chavdar Lyubomirov

2009-07-09

The subject of the current work is one of the main participants in the light-dependent phase of oxygenic photosynthesis, Photosystem I (PS I). This complex carries an immense number of cofactors: chlorophylls (Chl), carotenoids, quinones, etc, which together with the protein entity exhibit several exceptional properties. First, PS I has an ultrafast light energy trapping kinetics with a nearly 100% quantum efficiency. Secondly, both of the electron transfer branches in the reaction center are suggested to be active. Thirdly, there are some so called 'red' Chls in the antenna system of PS I, absorbing light with longer wavelengths than the reaction center. These 'red' Chls significantly modify the trapping kinetics of PS I. The purpose of this thesis is to obtain better understanding of the above-mentioned, specific features of PS I. This will not merely cast more light on the mechanisms of energy and electron transfer in the complex, but also will contribute to the future developments of optimized artificial light-harvesting systems. In the current work, a number of PS I complexes isolated from different organisms (Thermosynechococcus elongatus, Chlamydomonas reinhardtii, Arabidopsis thaliana) and possessing distinctive features (different macroorganisation, monomers, trimers, monomers with a semibelt of peripheral antenna attached; presence of 'red' Chls) is investigated. The studies are primarily focused on the electron transfer kinetics in each of the cofactor branches in the PS I reaction center, as well as on the effect of the antenna size and the presence of 'red' Chls on the trapping kinetics of PS I. These aspects are explored with the help of several ultrafast optical spectroscopy methods: (i) time-resolved fluorescence ? single photon counting and synchroscan streak camera; and (ii) ultrafast transient absorption. Physically meaningful information about the molecular mechanisms of the energy trapping in PS I is

SurfKin: an ab initio kinetic code for modeling surface reactions.

Science.gov (United States)

Le, Thong Nguyen-Minh; Liu, Bin; Huynh, Lam K

2014-10-05

In this article, we describe a C/C++ program called SurfKin (Surface Kinetics) to construct microkinetic mechanisms for modeling gas-surface reactions. Thermodynamic properties of reaction species are estimated based on density functional theory calculations and statistical mechanics. Rate constants for elementary steps (including adsorption, desorption, and chemical reactions on surfaces) are calculated using the classical collision theory and transition state theory. Methane decomposition and water-gas shift reaction on Ni(111) surface were chosen as test cases to validate the code implementations. The good agreement with literature data suggests this is a powerful tool to facilitate the analysis of complex reactions on surfaces, and thus it helps to effectively construct detailed microkinetic mechanisms for such surface reactions. SurfKin also opens a possibility for designing nanoscale model catalysts. Copyright © 2014 Wiley Periodicals, Inc.

Thermodynamics of axial substitution and kinetics of reactions with amino acids for the paddlewheel complex tetrakis(acetato)chloridodiruthenium(II,III).

Science.gov (United States)

Santos, Rodrigo L S R; van Eldik, Rudi; de Oliveira Silva, Denise

2012-06-18

The known paddlewheel, tetrakis(acetato)chloridodiruthenium(II,III), offers a versatile synthetic route to a novel class of antitumor diruthenium(II,III) metallo drugs, where the equatorial ligands are nonsteroidal anti-inflammatory carboxylates. This complex was studied here as a soluble starting prototype model for antitumor analogues to elucidate the reactivity of the [Ru(2)(CH(3)COO)(4)](+) framework. Thermodynamic studies on equilibration reactions for axial substitution of water by chloride and kinetic studies on reactions of the diaqua complexes with the amino acids glycine, cysteine, histidine, and tryptophan were performed. The standard thermodynamic reaction parameters ΔH°, ΔS°, and ΔV° were determined and showed that both of the sequential axial substitution reactions are enthalpy driven. Kinetic rate laws and rate constants were determined for the axial substitution reactions of coordinated water by the amino acids that gave the corresponding aqua(amino acid)-Ru(2) substituted species. The results revealed that the [Ru(2)(CH(3)COO)(4)](+) paddlewheel framework remained stable during the axial ligand substitution reactions and was also mostly preserved in the presence of the amino acids.

On the Mathematical Structure of Balanced Chemical Reaction Networks Governed by Mass Action Kinetics

NARCIS (Netherlands)

Schaft, Arjan van der; Rao, Shodhan; Jayawardhana, Bayu

2013-01-01

Motivated by recent progress on the interplay between graph theory, dynamics, and systems theory, we revisit the analysis of chemical reaction networks described by mass action kinetics. For reaction networks possessing a thermodynamic equilibrium we derive a compact formulation exhibiting at the

BGK-type models in strong reaction and kinetic chemical equilibrium regimes

International Nuclear Information System (INIS)

Monaco, R; Bianchi, M Pandolfi; Soares, A J

2005-01-01

A BGK-type procedure is applied to multi-component gases undergoing chemical reactions of bimolecular type. The relaxation process towards local Maxwellians, depending on mass and numerical densities of each species as well as common velocity and temperature, is investigated in two different cases with respect to chemical regimes. These cases are related to the strong reaction regime characterized by slow reactions, and to the kinetic chemical equilibrium regime where fast reactions take place. The consistency properties of both models are stated in detail. The trend to equilibrium is numerically tested and comparisons for the two regimes are performed within the hydrogen-air and carbon-oxygen reaction mechanism. In the spatial homogeneous case, it is also shown that the thermodynamical equilibrium of the models recovers satisfactorily the asymptotic equilibrium solutions to the reactive Euler equations

Kinetic aspects of the embedded clusters: Reaction - Rate Theory

International Nuclear Information System (INIS)

Despa, F.; Apostol, M.

1995-07-01

The main stages of the cluster growth process are reviewed using Reaction - Rate Theory. The precipitation stage is shown as a relaxation of the solute towards a cluster state characterized by a higher stability. The kinetic of the late stage of phase separation, the coarsening process, is analyzed by an off-centre diffusion mechanism. The theoretical results are compared to the experimental ones. (author). 37 refs, 6 figs

The browning kinetics of the non-enzymatic browning reaction in L-ascorbic acid/basic amino acid systems

Directory of Open Access Journals (Sweden)

Ai-Nong YU

Full Text Available Abstract Under the conditions of weak basis and the reaction temperature range of 110-150 °C, lysine, arginine and histidine were reacted with L-ascorbic acid at equal amount for 30-150 min, respectively and the formation of browning products was monitored with UV–vis spectrometry. The kinetic characteristics of their non-enzymatic browning reaction were investigated. The study results indicated that the non-enzymatic browning reaction of these three amino acids with L-ascorbic acid to form browning products was zero-order reaction. The apparent activation energies for the formation of browning products from L-ascorbic acid/lysine, L-ascorbic acid/arginine and L-ascorbic acid/histidine systems were 54.94, 50.08 and 35.31kJ/mol. The activation energy data indicated the degree of effects of reaction temperature on non-enzymatic browning reaction. Within the temperature range of 110-150 °C, the reaction rate of L-ascorbic acid/lysine system was the fastest one, followed by that of the L-ascorbic acid/arginine system. The reaction rate of L-ascorbic acid/histidine system was the slowest one. Based on the observed kinetic data, the formation mechanisms of browning products were proposed.

Heterogeneous photocatalysis of real textile wastewater: evaluation of reaction kinetics and characterization.

Science.gov (United States)

Sahoo, Chittaranjan; Gupta, Ashok K; Pillai, Indu M Sasidharan

2012-01-01

Real textile wastewater collected from the cotton dyeing bath of a fabric dyeing and finishing plant was subjected to heterogeneous photocatalysis using Ag(+) doped TiO(2) under UV irradiation in a batch reactor. The photocatalysts were characterized by FESEM, XRD, EDS, FTIR, DRS and BET analyses. The kinetics of the reaction was also evaluated. Colour removal was more than 88%, 94% and 99%, respectively for undiluted, 2 times diluted and 5 times diluted wastewater with Ag(+) doped TiO(2) (2.5 g/L) after UV irradiation for 360 minutes. The COD removal for undiluted, 2 times diluted and 5 times diluted wastewater was 47%, 70% and 92%, respectively under similar conditions. The reaction followed Langmuir-Hinshelwood pseudo first order kinetic model and the data fitted well to polynomial regression analysis.

Spectroscopic and Kinetic Characterization of Peroxidase-Like π-Cation Radical Pinch-Porphyrin-Iron(III Reaction Intermediate Models of Peroxidase Enzymes

Directory of Open Access Journals (Sweden)

Samuel Hernández Anzaldo

2016-06-01

Full Text Available The spectroscopic and kinetic characterization of two intermediates from the H2O2 oxidation of three dimethyl ester [(proto, (meso, (deuteroporphyrinato (picdien]Fe(III complexes ([FePPPic], [FeMPPic] and [FeDPPic], respectively pinch-porphyrin peroxidase enzyme models, with s = 5/2 and 3/2 Fe(III quantum mixed spin (qms ground states is described herein. The kinetic study by UV/Vis at λmax = 465 nm showed two different types of kinetics during the oxidation process in the guaiacol test for peroxidases (1–3 + guaiacol + H2O2 → oxidation guaiacol products. The first intermediate was observed during the first 24 s of the reaction. When the reaction conditions were changed to higher concentration of pinch-porphyrins and hydrogen peroxide only one type of kinetics was observed. Next, the reaction was performed only between pinch-porphyrins-Fe(III and H2O2, resulting in only two types of kinetics that were developed during the first 0–4 s. After this time a self-oxidation process was observed. Our hypotheses state that the formation of the π-cation radicals, reaction intermediates of the pinch-porphyrin-Fe(III family with the ligand picdien [N,N’-bis-pyridin-2-ylmethyl-propane-1,3-diamine], occurred with unique kinetics that are different from the overall process and was involved in the oxidation pathway. UV-Vis, 1H-NMR and ESR spectra confirmed the formation of such intermediates. The results in this paper highlight the link between different spectroscopic techniques that positively depict the kinetic traits of artificial compounds with enzyme-like activity.

Kinetic investigation of the chlorine reduction reaction on electrochemically oxidised ruthenium

International Nuclear Information System (INIS)

Thomassen, M.; Karlsen, C.; Borresen, B.; Tunold, R.

2006-01-01

The rate and mechanism of the electroreduction of chlorine on electrooxidised ruthenium has been investigated with focus on the effect of solution pH. Current/potential curves for the reduction process in solutions with constant chloride concentration of 1.0 mol dm -3 and varying H + concentration have been obtained with the use of the rotating disk electrode technique (RDE). It was found that the chlorine reduction rate is highly inhibited in solutions with high H + concentrations and that it can be satisfactorily described by the Erenburg mechanism, previously suggested for the chlorine evolution on RuO 2 and RTO. The expression of the kinetic current as a function of chlorine and H + concentration was obtained by solving the elementary rate equations of the kinetic mechanism. The kinetic constants obtained from the correlation of the kinetic current expression to the experimental data were used to simulate the dependence of the surface coverages and elementary reaction rates on overpotential

Reaction kinetics of irradiation prepolymerized MMA-PU IPN by 5DXC FTIR

International Nuclear Information System (INIS)

Wu Yiming; Zhang Zhiping; Luo Ning

2000-01-01

The reaction kinetics of irradiation-prepolymerized MMA-PU (polyether) IPNs have been studied by FTIR. The results indicate that the polymerization of each component in the IPN follows its normal distinct reaction mechanism with no mutual interference. Increasing the concentration of TMPTAM (crosslinking agent of PMMA) increased the formation rate of PMMA, while the formation rate of PU networks remained almost the same. Increasing the concentration of TMP (crosslinking agent of PU) increased the formation rate of PU, while the formation rate of PMMA networks decreased. The formation rate of PU was obviously faster than that of PMMA. A theory for the cage effect of the PU network has been proposed. (author)

Kinetics and Mechanism of the Reaction of Hydoxyl Radicals with Acetonitrile under Atmospheric Conditions

Science.gov (United States)

Hynes, A. J.; Wine, P. H.

1997-01-01

The pulsed laser photolysis-pulsed laser induced fluorescence technique has been employed to determine absolute rate coefficients for the reaction OH + CH3CN (1) and its isotopic variants, OH + CD3CN (2), OD + CH3CN (3), and OD + CD3CN (4). Reactions 1 and 2 were studied as a function of pressure and temperature in N2, N2/O2, and He buffer gases. In the absence of O2 all four reactions displayed well-behaved kinetics with exponential OH decays and pseudo-first rate constants which were proportional to substrate concentration. Data obtained in N2 over the range 50-700 Torr at 298 K are consistent with k(sub 1), showing a small pressure dependence. The Arrhenius expression obtained by averaging data at all pressures in k(sub 1)(T) = (1.1(sup +0.5)/(sub -0.3)) x 10(exp -12) exp[(-1130 +/- 90)/T] cu cm /(molecule s). The kinetics of reaction 2 are found to be pressure dependent with k(sub 2) (298 K) increasing from (1.21 +/- 0.12) x 10(exp -14) to (2.16 +/- 0.11) x 10(exp -14) cm(exp 3)/ (molecule s) over the pressure range 50-700 Torr of N2 at 298 K. Data at pressures greater than 600 Torr give k(sub 2)(T) = (9.4((sup +13.4)(sub -5.0))) x 10(exp -13) exp[(-1180 +/- 250)/T] cu cm/(molecule s). The rates of reactions 3 and 4 are found to be independent of pressure over the range 50-700 Torr of N2 with 298 K rate coefficient given by k(sub 3) =(3.18 +/- 0.40) x 10(exp -14) cu cm/(molecule s) and k(sub 4) = (2.25 +/-0.28) x 10(exp -14) cu cm/(molecule s). In the presence of O2 each reaction shows complex (non-pseudo-first-order) kinetic behavior and/or an apparent decrease in the observed rate constant with increasing [O2], indicating the presence of significant OH or OD regeneration. Observation of regeneration of OH in (2) and OD in (3) is indicative of a reaction channel which proceeds via addition followed by reaction of the adduct, or one of its decomposition products, with O2. The observed OH and OD decay profiles have been modeled by using a simple mechanistic

Kinetics of the reactions of bromine atoms with a series of aliphatic aldehydes at 298 K

Energy Technology Data Exchange (ETDEWEB)

Szilagyi, I.; Imrik, K.; Dobe, S.; Berces, T. [Magyar Tudomanyos Akademia, Budapest (Hungary). Koezponti Kemiai Kutato Intezete

1998-01-01

The kinetics of the reactions of Br({sup 2}P{sub 3/2}) with selected aldehydes, i.e. ethanal (1), propanal (2), 2-methyl-propanal (3), 2.2-dimethyl-propanal (4) and trichloroacetaldehyde (5) were studied at 298{+-}2 K. Rate constants for overall reactions were measured using the fast flow technique with resonance fluorescence detection of Br. Complementary determinations were carried out by the laser flash photolysis method. The following rate constants were obtained in the kinetic measurements ({+-}2{sigma}): k{sub 1}=(2.1{+-}0.2) x 10{sup 12}, k{sub 2}=(4.3{+-}0.4) x 10{sup 12}, k{sub 3}=(6.3{+-}1.4) x 10{sup 12}, k{sub 4}=(8.5{+-}0.8) x 10{sup 12}, k{sub 5}{<=}1 x 10{sup 9}, all in cm{sup 3}mol{sup -1}s{sup -1} units. The probable mechanism for the reactions of bromine atoms with aliphatic aldehydes has been discussed. (orig.)

Programming chemical kinetics: engineering dynamic reaction networks with DNA strand displacement

Science.gov (United States)

Srinivas, Niranjan

Over the last century, the silicon revolution has enabled us to build faster, smaller and more sophisticated computers. Today, these computers control phones, cars, satellites, assembly lines, and other electromechanical devices. Just as electrical wiring controls electromechanical devices, living organisms employ "chemical wiring" to make decisions about their environment and control physical processes. Currently, the big difference between these two substrates is that while we have the abstractions, design principles, verification and fabrication techniques in place for programming with silicon, we have no comparable understanding or expertise for programming chemistry. In this thesis we take a small step towards the goal of learning how to systematically engineer prescribed non-equilibrium dynamical behaviors in chemical systems. We use the formalism of chemical reaction networks (CRNs), combined with mass-action kinetics, as our programming language for specifying dynamical behaviors. Leveraging the tools of nucleic acid nanotechnology (introduced in Chapter 1), we employ synthetic DNA molecules as our molecular architecture and toehold-mediated DNA strand displacement as our reaction primitive. Abstraction, modular design and systematic fabrication can work only with well-understood and quantitatively characterized tools. Therefore, we embark on a detailed study of the "device physics" of DNA strand displacement (Chapter 2). We present a unified view of strand displacement biophysics and kinetics by studying the process at multiple levels of detail, using an intuitive model of a random walk on a 1-dimensional energy landscape, a secondary structure kinetics model with single base-pair steps, and a coarse-grained molecular model that incorporates three-dimensional geometric and steric effects. Further, we experimentally investigate the thermodynamics of three-way branch migration. Our findings are consistent with previously measured or inferred rates for

The Nanoconfined Free Radical Polymerization: Reaction Kinetics and Thermodynamics

Science.gov (United States)

Zhao, Haoyu; Simon, Sindee

The reaction kinetics and thermodynamics of nanoconfined free radical polymerizations are investigated for methyl methacrylate (MMA) and ethyl methacrylate (EMA) monomers using differential scanning calorimetry. Controlled pore glass is used as the confinement medium with pore diameters as small as 7.5 nm; the influence of both hydrophobic (silanized such that trimethylsilyl groups cover the surface) and hydrophilic (native silanol) surfaces is investigated. Propagation rates increase when monomers are reacted in the hydrophilic pores presumably due to the specific interactions between the carbonyl and silanol groups; however, the more flexible EMA monomer shows weaker effects. On the other hand, initial rates of polymerization in hydrophobic pores are unchanged from the bulk. In both pores, the onset of autoacceleration occurs earlier due to the reduced diffusivity of confined chains, which may be compensated at high temperatures. In addition to changes in kinetics, the reaction thermodynamics can be affected under nanoconfinement. Specifically, the ceiling temperature (Tc) is shifted to lower temperatures in nanopores, with pore surface chemistry showing no significant effects; the equilibrium conversion is also reduced at high temperatures below Tc. These observations are attributed to a larger negative change in entropy on propagation for the confined system, with the MMA system again showing greater effects. Funding from ACS PRF is gratefully acknowledged.

The Study of a Simple Redox Reaction as an Experimental Approach to Chemical Kinetics.

Science.gov (United States)

Elias, Horst; Zipp, Arden P.

1988-01-01

Recommends using iodide ions and peroxodisulfate ions for studying rate laws instead of the standard iodine clock for kinetic study. Presents the methodology and a discussion of the kinetics involved for a laboratory experiment for a high school or introductory college course. (ML)

An experimental and theoretical study of reaction steps relevant to the methanol-to-hydrocarbons reaction

Energy Technology Data Exchange (ETDEWEB)

Svelle, Stian

2004-07-01

The primary objective of the present work is to obtain new insight into the reaction mechanism of the zeolite catalyzed methanol-to-hydrocarbons (MTH) reaction. It was decided to use both experimental and computational techniques to reach this goal. An investigation of the n-butene + methanol system was therefore initiated. Over time, it became apparent that it was possible to determine the rate for the methylation of n-butene by methanol. The ethene and propene systems were therefore reexamined in order to collect kinetic information also for those cases. With the development of user-friendly quantum chemistry programs such as the Gaussian suite of programs, the possibility of applying quantum chemical methods to many types of problems has become readily available even for non-experts. When performing mechanistic studies, there is quite often a considerable synergy effect when combining experimental and computational approaches. The methylation reactions mentioned above turned out to be an issue well suited for quantum chemical investigations. The incentive for examining the halomethane reactivity was the clear analogy to the MTH reaction system. Alkene dimerization was also a reaction readily examined with quantum chemistry. As discussed in the introduction of this thesis, polymethylbenzenes, or their cationic counterparts, are suspected to be key intermediates in the MTH reaction. It was therefore decided to investigate the intrinsic reactivity of these species in the gas-phase by employing sophisticated mass spectrometric (MS) techniques in collaboration with the MS group at the Department of Chemistry, University of Oslo The data thus obtained will also be compared with results from an ongoing computational study on gas phase polymethylbenzenium reactivity. 6 papers presenting various studies are included. The titles are: 1) A Theoretical Investigation of the Methylation of Alkenes with Methanol over Acidic Zeolites. 2) A Theoretical Investigation of the

Kinetic Studies of Oxidative Coupling of Methane Reaction on Model Catalysts

KAUST Repository

Khan, Abdulaziz M.

2016-04-26

With the increasing production of natural gas as a result of the advancement in the technology, methane conversion to more valuable products has become a must. One of the most attractive processes which allow the utilization of the world’s most abundant hydrocarbon is the oxidative coupling. The main advantage of this process is the ability of converting methane into higher paraffins and olefins (primarily C2) in a direct way using a single reactor. Nevertheless, low C2+ yields have prevented the process to be commercialized despite the fact that great number of attempts to prepare catalysts were conducted so that it can be economically viable. Due to these limitations, understanding the mechanism and kinetics of the reaction can be utilized in improving the catalysts’ performance. The reaction involves the formation of methyl radicals that undergo gas-phase radical reactions. CH4 activation is believed to be done the surface oxygen species. However, recent studies showed that, in addition to the surface oxygen mediated pathway, an OH radical mediated pathway have a large contribution on the CH4 activation. The experiments of Li/MgO, Sr/La2O3 and NaWO4/SiO2 catalysts revealed variation of behavior in activity and selectivity. In addition, water effect analysis showed that Li/MgO deactivate at the presence of water due to sintering phenomena and the loss of active sites. On the other hand, negative effect on the C2 yield and CH4 conversion rate was observed with Sr/La2O3 with increasing the water partial pressure. Na2WO4/SiO2 showed a positive behavior with water in terms of CH4 conversion and C2 yield. In addition, the increment in CH4 conversion rate was found to be proportional with PO2 ¼ PH2O ½ which is consistent with the formation of OH radicals and the OH-mediated pathway. Experiments of using ring-dye laser, which is used to detect OH in combustion experiments, were tried in order to detect OH radicals in the gas-phase of the catalyst. Nevertheless

Gas phase polymerization of propylene. Reaction kinetics and molecular weight distribution

NARCIS (Netherlands)

Meier, G.B.; Weickert, G.; van Swaaij, Willibrordus Petrus Maria

2001-01-01

Gas-phase polymerizations have been executed at different temperatures, pressures, and hydrogen concentrations using Me2Si[Ind]2ZrCl2 / methylaluminoxane / SiO2(Pennsylvania Quarts) as a catalyst. The reaction rate curves have been described by a kinetic model, which takes into account the initially

Kinetic Study on the Esterification of Palm Fatty Acid Distillate (PFAD) Using Heterogeneous Catalyst

Science.gov (United States)

Rofiqah, U.; Djalal, R. A.; Sutrisno, B.; Hidayat, A.

2018-05-01

Esterification with heterogeneous catalysts is believed to have advantages compared to homogeneous catalysts. Palm Fatty Acid Distillate (PFAD) was esterified by ZrO2 -SO4 2-/natural zeolite at temperature variation of 55°C, 60°C, and 65°C to produce biodiesel. Determination of reaction kinetics was done by experiment and modeling. Kinetic study was approached using pseudo-homogeneous model of first order. For experiment, reaction kinetics were 0.0031 s-1, 0.0054 s-1, and 0.00937 s-1 for a temperature of 55 °C, 60 °C and 65 °C, respectively. For modelling, reaction kinetics were 0.0030 s-1, 0.0055 s-1, and 0.0090 s-1 for a temperature of 55°C, 60°C and 65°C, respectively. Rate and conversion of reaction are getting increased by increasing temperature.

Study on reaction mechanism by analysis of kinetic energy spectra of light particles and formation of final products

Science.gov (United States)

Giardina, G.; Mandaglio, G.; Nasirov, A. K.; Anastasi, A.; Curciarello, F.; Fazio, G.

2018-05-01

The sensitivity of reaction mechanism in the formation of compound nucleus (CN) by the analysis of kinetic energy spectra of light particles and of reaction products are shown. The dependence of the P CN fusion probability of reactants and W sur survival probability of CN against fission at its deexcitation on the mass and charge symmetries in the entrance channel of heavy-ion collisions, as well as on the neutron numbers is discussed. The possibility of conducting a complex program of investigations of the complete fusion by reliable ways depends on the detailed and refined methods of experimental and theoretical analyses.

Kinetic isotope effects in the CH4 + H→CH3 + H2 system. Predictions of the LMR six-body potential-energy reaction hypersurface

International Nuclear Information System (INIS)

Marriott, T.D.

1976-01-01

Scope of Study: The purpose of this study was two-fold. First, it served to test, in part, the usefulness of the LMR six-body potential-energy surface (LMR-PES) for transition-state theory predictions of the kinetic isotope effects for both the forward and reverse reactions of CH 4 + H reversible CH 3 + H 2 . In this regard the agreement between experimental and theoretical isotope effects, assuming the former to be accurate, provides information about the accuracy of the curvature of the potential energy surface for motion both parallel and perpendicular to the reaction coordinate. Second, these isotope effects were used to assess the validity of a number of qualitative and semi-quantitative interpretations of kinetic isotope effects developed in physical organic chemistry with regard to this reaction system. The force constants and geometries obtained numerically from the LMR-PES were found to produce reasonable harmonic approximations to the reactant normal mode frequencies. Neglecting tunneling, the LMR-PES reasonably reproduces the experimental k/sub H//k/sub D/ values for the reactions CH 4 + H(D), CH 3 + HD(DH) and CD 2 + HD(DH). Since previous theoretical treatments of primary deuterium kinetic isotope effects have neglected the bending normal mode frequencies, a semi-quantitative study of the effect of neglecting bending frequencies on the VP, EXC, and ZPE elements as well as the transition-state theory kinetic isotope effects was performed. The Swain-Schaad relationship between primary deuterium and tritium kinetic isotope effects was shown to hold to a reasonable degree of accuracy for the LMR-PES reaction system. A relationship between 13-carbon and 14-carbon kinetic isotope effects similar to the Swain-Schaad relationship was derived

Bayesian inference of chemical kinetic models from proposed reactions

KAUST Repository

Galagali, Nikhil

2015-02-01

© 2014 Elsevier Ltd. Bayesian inference provides a natural framework for combining experimental data with prior knowledge to develop chemical kinetic models and quantify the associated uncertainties, not only in parameter values but also in model structure. Most existing applications of Bayesian model selection methods to chemical kinetics have been limited to comparisons among a small set of models, however. The significant computational cost of evaluating posterior model probabilities renders traditional Bayesian methods infeasible when the model space becomes large. We present a new framework for tractable Bayesian model inference and uncertainty quantification using a large number of systematically generated model hypotheses. The approach involves imposing point-mass mixture priors over rate constants and exploring the resulting posterior distribution using an adaptive Markov chain Monte Carlo method. The posterior samples are used to identify plausible models, to quantify rate constant uncertainties, and to extract key diagnostic information about model structure-such as the reactions and operating pathways most strongly supported by the data. We provide numerical demonstrations of the proposed framework by inferring kinetic models for catalytic steam and dry reforming of methane using available experimental data.

Influence of Proton Acceptors on the Proton-Coupled Electron Transfer Reaction Kinetics of a Ruthenium-Tyrosine Complex.

Science.gov (United States)

Lennox, J Christian; Dempsey, Jillian L

2017-11-22

A polypyridyl ruthenium complex with fluorinated bipyridine ligands and a covalently bound tyrosine moiety was synthesized, and its photo-induced proton-coupled electron transfer (PCET) reactivity in acetonitrile was investigated with transient absorption spectroscopy. Using flash-quench methodology with methyl viologen as an oxidative quencher, a Ru 3+ species is generated that is capable of initiating the intramolecular PCET oxidation of the tyrosine moiety. Using a series of substituted pyridine bases, the reaction kinetics were found to vary as a function of proton acceptor concentration and identity, with no significant H/D kinetic isotope effect. Through analysis of the kinetics traces and comparison to a control complex without the tyrosine moiety, PCET reactivity was found to proceed through an equilibrium electron transfer followed by proton transfer (ET-PT) pathway in which irreversible deprotonation of the tyrosine radical cation shifts the ET equilibrium, conferring a base dependence on the reaction. Comprehensive kinetics modeling allowed for deconvolution of complex kinetics and determination of rate constants for each elementary step. Across the five pyridine bases explored, spanning a range of 4.2 pK a units, a linear free-energy relationship was found for the proton transfer rate constant with a slope of 0.32. These findings highlight the influence that proton transfer driving force exerts on PCET reaction kinetics.

Stepwise kinetic equilibrium models of quantitative polymerase chain reaction

Directory of Open Access Journals (Sweden)

Cobbs Gary

2012-08-01

Full Text Available Abstract Background Numerous models for use in interpreting quantitative PCR (qPCR data are present in recent literature. The most commonly used models assume the amplification in qPCR is exponential and fit an exponential model with a constant rate of increase to a select part of the curve. Kinetic theory may be used to model the annealing phase and does not assume constant efficiency of amplification. Mechanistic models describing the annealing phase with kinetic theory offer the most potential for accurate interpretation of qPCR data. Even so, they have not been thoroughly investigated and are rarely used for interpretation of qPCR data. New results for kinetic modeling of qPCR are presented. Results Two models are presented in which the efficiency of amplification is based on equilibrium solutions for the annealing phase of the qPCR process. Model 1 assumes annealing of complementary targets strands and annealing of target and primers are both reversible reactions and reach a dynamic equilibrium. Model 2 assumes all annealing reactions are nonreversible and equilibrium is static. Both models include the effect of primer concentration during the annealing phase. Analytic formulae are given for the equilibrium values of all single and double stranded molecules at the end of the annealing step. The equilibrium values are then used in a stepwise method to describe the whole qPCR process. Rate constants of kinetic models are the same for solutions that are identical except for possibly having different initial target concentrations. Analysis of qPCR curves from such solutions are thus analyzed by simultaneous non-linear curve fitting with the same rate constant values applying to all curves and each curve having a unique value for initial target concentration. The models were fit to two data sets for which the true initial target concentrations are known. Both models give better fit to observed qPCR data than other kinetic models present in the

Stepwise kinetic equilibrium models of quantitative polymerase chain reaction.

Science.gov (United States)

Cobbs, Gary

2012-08-16

Numerous models for use in interpreting quantitative PCR (qPCR) data are present in recent literature. The most commonly used models assume the amplification in qPCR is exponential and fit an exponential model with a constant rate of increase to a select part of the curve. Kinetic theory may be used to model the annealing phase and does not assume constant efficiency of amplification. Mechanistic models describing the annealing phase with kinetic theory offer the most potential for accurate interpretation of qPCR data. Even so, they have not been thoroughly investigated and are rarely used for interpretation of qPCR data. New results for kinetic modeling of qPCR are presented. Two models are presented in which the efficiency of amplification is based on equilibrium solutions for the annealing phase of the qPCR process. Model 1 assumes annealing of complementary targets strands and annealing of target and primers are both reversible reactions and reach a dynamic equilibrium. Model 2 assumes all annealing reactions are nonreversible and equilibrium is static. Both models include the effect of primer concentration during the annealing phase. Analytic formulae are given for the equilibrium values of all single and double stranded molecules at the end of the annealing step. The equilibrium values are then used in a stepwise method to describe the whole qPCR process. Rate constants of kinetic models are the same for solutions that are identical except for possibly having different initial target concentrations. Analysis of qPCR curves from such solutions are thus analyzed by simultaneous non-linear curve fitting with the same rate constant values applying to all curves and each curve having a unique value for initial target concentration. The models were fit to two data sets for which the true initial target concentrations are known. Both models give better fit to observed qPCR data than other kinetic models present in the literature. They also give better estimates of

A study of butyl acetate synthesis. 4-reaction kinetics

OpenAIRE

Álvaro Orjuela Londoño; Fernando Leiva Lenis; Luis Alejandro Boyacá Mendivelso; Gerardo Rodríguez Niño; Luis María Carballo Suárez

2006-01-01

This work was aimed at studying liquid-phase acetic acid and butyl alcohol esterification reaction (P atm =0.76 Bar),using an ion exchange resin (Lewatit K-2431) as catalyst. The effect of the absence of internal and external mass transport on catalyst particles was established in the research conditions used here. A set of assays to determine the effect of catalyst load (0.5%, 1%, 2% w/w) temperature (73°C, 80°C, 87°C) and molar ratio (1:2, 1:1, 2:1 acid/alcohol) on reaction rate was carrie...

Experimental study and kinetic modeling of the hydro-fluorination of uranium dioxide

International Nuclear Information System (INIS)

Pages, Simon

2014-01-01

A kinetic study of hydro-fluorination of uranium dioxide was performed between 375 and 475 C under partial pressures of HF between 42 and 720 mbar. The reaction was followed by thermogravimetry in isothermal and isobaric conditions. The kinetic data obtained coupled with a characterization of the powder before, during and after reaction by SEM, EDS, BET and XRD showed that the powder grains of UO 2 are transformed according a model of instantaneous germination, anisotropic growth and internal development. The rate limiting step of the growth process is the diffusion of HF in the UF 4 layer. A mechanism of growth of the UF 4 layer has been proposed. In the temperature and pressure range studied, the reaction is of first order with respect to HF and follows an Arrhenius law. A rate equation was determined and used to perform kinetic simulations which have shown a very good correlation with experience. Coupling of this rate equation with heat and mass transport phenomena allowed to perform simulations at the scale of a powder's agglomerate. They have shown that some structures of agglomerates influence the rate of diffusion of the gases in the porous medium and thereby influence the reaction rate. Finally kinetic simulations on powder's beds and pellets were carried out and compared with experimental rates. The experimental and simulated kinetic curves have the same paces, but improvements in the simulations are needed to accurately predict rates: the coupling between the three scales (grain, agglomerate, oven) would be a good example. (author) [fr

Kinetic modeling of electron transfer reactions in photosystem I complexes of various structures with substituted quinone acceptors.

Science.gov (United States)

Milanovsky, Georgy E; Petrova, Anastasia A; Cherepanov, Dmitry A; Semenov, Alexey Yu

2017-09-01

The reduction kinetics of the photo-oxidized primary electron donor P 700 in photosystem I (PS I) complexes from cyanobacteria Synechocystis sp. PCC 6803 were analyzed within the kinetic model, which considers electron transfer (ET) reactions between P 700 , secondary quinone acceptor A 1 , iron-sulfur clusters and external electron donor and acceptors - methylviologen (MV), 2,3-dichloro-naphthoquinone (Cl 2 NQ) and oxygen. PS I complexes containing various quinones in the A 1 -binding site (phylloquinone PhQ, plastoquinone-9 PQ and Cl 2 NQ) as well as F X -core complexes, depleted of terminal iron-sulfur F A /F B clusters, were studied. The acceleration of charge recombination in F X -core complexes by PhQ/PQ substitution indicates that backward ET from the iron-sulfur clusters involves quinone in the A 1 -binding site. The kinetic parameters of ET reactions were obtained by global fitting of the P 700 + reduction with the kinetic model. The free energy gap ΔG 0 between F X and F A /F B clusters was estimated as -130 meV. The driving force of ET from A 1 to F X was determined as -50 and -220 meV for PhQ in the A and B cofactor branches, respectively. For PQ in A 1A -site, this reaction was found to be endergonic (ΔG 0  = +75 meV). The interaction of PS I with external acceptors was quantitatively described in terms of Michaelis-Menten kinetics. The second-order rate constants of ET from F A /F B , F X and Cl 2 NQ in the A 1 -site of PS I to external acceptors were estimated. The side production of superoxide radical in the A 1 -site by oxygen reduction via the Mehler reaction might comprise ≥0.3% of the total electron flow in PS I.

Golden rule kinetics of transfer reactions in condensed phase: The microscopic model of electron transfer reactions in disordered solid matrices

International Nuclear Information System (INIS)

Basilevsky, M. V.; Mitina, E. A.; Odinokov, A. V.; Titov, S. V.

2013-01-01

The algorithm for a theoretical calculation of transfer reaction rates for light quantum particles (i.e., the electron and H-atom transfers) in non-polar solid matrices is formulated and justified. The mechanism postulated involves a local mode (an either intra- or inter-molecular one) serving as a mediator which accomplishes the energy exchange between the reacting high-frequency quantum mode and the phonon modes belonging to the environment. This approach uses as a background the Fermi golden rule beyond the usually applied spin-boson approximation. The dynamical treatment rests on the one-dimensional version of the standard quantum relaxation equation for the reduced density matrix, which describes the frequency fluctuation spectrum for the local mode under consideration. The temperature dependence of a reaction rate is controlled by the dimensionless parameter ξ 0 =ℏω 0 /k B T where ω 0 is the frequency of the local mode and T is the temperature. The realization of the computational scheme is different for the high/intermediate (ξ 0 0 ≫ 1) temperature ranges. For the first (quasi-classical) kinetic regime, the Redfield approximation to the solution of the relaxation equation proved to be sufficient and efficient in practical applications. The study of the essentially quantum-mechanical low-temperature kinetic regime in its asymptotic limit requires the implementation of the exact relaxation equation. The coherent mechanism providing a non-vanishing reaction rate has been revealed when T→ 0. An accurate computational methodology for the cross-over kinetic regime needs a further elaboration. The original model of the hopping mechanism for electronic conduction in photosensitive organic materials is considered, based on the above techniques. The electron transfer (ET) in active centers of such systems proceeds via local intra- and intermolecular modes. The active modes, as a rule, operate beyond the kinetic regimes, which are usually postulated in the

Laccase-catalyzed removal of the antimicrobials chlorophene and dichlorophen from water: Reaction kinetics, pathway and toxicity evaluation.

Science.gov (United States)

Shi, Huanhuan; Peng, Jianbiao; Li, Jianhua; Mao, Liang; Wang, Zunyao; Gao, Shixiang

2016-11-05

As active agents in cleaning and disinfecting products, antimicrobials have been widely spread in the environment and have drawn extensive attention as potential threats to the ecological system and human health. In this study, the laccase-catalyzed removal of two emerging antimicrobials, chlorophene (CP) and dichlorophen (DCP), was investigated under simulated environmental conditions. Intrinsic reaction kinetics showed that the removal of CP and DCP followed second-order reaction kinetics, first-order with respect to both the enzyme and the substrate concentration. It was also found that fulvic acid could suppress the transformation of CP and DCP by reversing the oxidation reactions through its action as a scavenger of the free radical intermediates produced from reactions between laccase and the substrates. Several reaction products were identified by a quadrupole time-of-flight mass spectrometer, and detailed reaction pathways were proposed. For both CP and DCP, direct polymerization was the principal pathway, and the coupling patterns were further corroborated based on molecular modeling. The nucleophilic substitution of chlorine by the hydroxyl group was observed, and further oxidation products capable of coupling with each other were also found. Additionally, toxicity evaluation tests using Scenedesmus obliquus confirmed that the toxicity of CP and DCP was effectively eliminated during the reaction processes. Copyright © 2016 Elsevier B.V. All rights reserved.

Kinetics of reaction of 1,10- decanedioland dimeric fatty acid C36

International Nuclear Information System (INIS)

Falah, A.

2013-01-01

Kinetic studies were carried out on the reaction between 1,10- Decanedioland dimeric fatty acid C 3 6 in melt phase. The reaction was performed at 140, 150, 160, 170, and 185 o C and followed by determining the acid value of the product. The polyesterfication reaction was found to be of overall second order with an activation energy of 39,91kj/mol up to (50, 44, 55,42, 63)% conversion at (140, 150, 160, 170, 185) o C and overall third order with an activation energy of 71.17 k j/ mol above (50, 44, 55, 42, 63)% conversion at (140, 150, 160, 170, 185) o C. The Degree of Polymerization, number average molecular weight and weight average molecular weight have been calculated during different times, the relationships between Degree of Polymerization, number average molecular weight, weight average molecular weight and the times is linear until, (50, 44, 55, 42, 63)%conversion at (140, 150, 160, 170, 185) o C. (author)

Noise-Induced Modulation of the Relaxation Kinetics around a Non-Equilibrium Steady State of Non-Linear Chemical Reaction Networks

OpenAIRE

Ramaswamy, Rajesh; Sbalzarini, Ivo F; González-Segredo, Nélido

2011-01-01

Stochastic effects from correlated noise non-trivially modulate the kinetics of non-linear chemical reaction networks. This is especially important in systems where reactions are confined to small volumes and reactants are delivered in bursts. We characterise how the two noise sources confinement and burst modulate the relaxation kinetics of a non-linear reaction network around a non-equilibrium steady state. We find that the lifetimes of species change with burst input and confinement. Confi...

Modeling Ignition of a Heptane Isomer: Improved Thermodynamics, Reaction Pathways, Kinetic, and Rate Rule Optimizations for 2-Methylhexane

KAUST Repository

Mohamed, Samah; Cai, Liming; Khaled, Fathi; Banyon, Colin; Wang, Zhandong; Rachidi, Mariam El; Pitsch, Heinz; Curran, Henry J.; Farooq, Aamir; Sarathy, Mani

2016-01-01

Accurate chemical kinetic combustion models of lightly branched alkanes (e.g., 2-methylalkanes) are important to investigate the combustion behavior of real fuels. Improving the fidelity of existing kinetic models is a necessity, as new experiments and advanced theories show inaccuracies in certain portions of the models. This study focuses on updating thermodynamic data and the kinetic reaction mechanism for a gasoline surrogate component, 2-methylhexane, based on recently published thermodynamic group values and rate rules derived from quantum calculations and experiments. Alternative pathways for the isomerization of peroxy-alkylhydroperoxide (OOQOOH) radicals are also investigated. The effects of these updates are compared against new high-pressure shock tube and rapid compression machine ignition delay measurements. It is shown that rate constant modifications are required to improve agreement between kinetic modeling simulations and experimental data. We further demonstrate the ability to optimize the kinetic model using both manual and automated techniques for rate parameter tunings to improve agreement with the measured ignition delay time data. Finally, additional low temperature chain branching reaction pathways are shown to improve the model’s performance. The present approach to model development provides better performance across extended operating conditions while also strengthening the fundamental basis of the model.

Modeling Ignition of a Heptane Isomer: Improved Thermodynamics, Reaction Pathways, Kinetic, and Rate Rule Optimizations for 2-Methylhexane

KAUST Repository

Mohamed, Samah

2016-03-21

Accurate chemical kinetic combustion models of lightly branched alkanes (e.g., 2-methylalkanes) are important to investigate the combustion behavior of real fuels. Improving the fidelity of existing kinetic models is a necessity, as new experiments and advanced theories show inaccuracies in certain portions of the models. This study focuses on updating thermodynamic data and the kinetic reaction mechanism for a gasoline surrogate component, 2-methylhexane, based on recently published thermodynamic group values and rate rules derived from quantum calculations and experiments. Alternative pathways for the isomerization of peroxy-alkylhydroperoxide (OOQOOH) radicals are also investigated. The effects of these updates are compared against new high-pressure shock tube and rapid compression machine ignition delay measurements. It is shown that rate constant modifications are required to improve agreement between kinetic modeling simulations and experimental data. We further demonstrate the ability to optimize the kinetic model using both manual and automated techniques for rate parameter tunings to improve agreement with the measured ignition delay time data. Finally, additional low temperature chain branching reaction pathways are shown to improve the model’s performance. The present approach to model development provides better performance across extended operating conditions while also strengthening the fundamental basis of the model.

Kinetics of the reaction of F atoms with O₂ and UV spectrum of FO₂ radicals in the gas phase at 295 K

DEFF Research Database (Denmark)

Ellermann, T.; Sehested, J.; Nielsen, O.J.

1994-01-01

The ultraviolet absorption spectrum of FO2 radicals and the kinetics of the reaction of F atoms with O2 have been studied in the gas phase at 295 K using pulse radiolysis combined with kinetic UV spectroscopy. At 230 nm, sigma(FO2) = (5.08 +/- 0.70) X 10(-18) cm2 molecule-1. The kinetics of the r......The ultraviolet absorption spectrum of FO2 radicals and the kinetics of the reaction of F atoms with O2 have been studied in the gas phase at 295 K using pulse radiolysis combined with kinetic UV spectroscopy. At 230 nm, sigma(FO2) = (5.08 +/- 0.70) X 10(-18) cm2 molecule-1. The kinetics...

An experimental and theoretical study of reaction steps relevant to the methanol-to-hydrocarbons reaction

Energy Technology Data Exchange (ETDEWEB)

Svelle, Stian

2004-07-01

The primary objective of the present work is to obtain new insight into the reaction mechanism of the zeolite catalyzed methanol-to-hydrocarbons (MTH) reaction. It was decided to use both experimental and computational techniques to reach this goal. An investigation of the n-butene + methanol system was therefore initiated. Over time, it became apparent that it was possible to determine the rate for the methylation of n-butene by methanol. The ethene and propene systems were therefore reexamined in order to collect kinetic information also for those cases. With the development of user-friendly quantum chemistry programs such as the Gaussian suite of programs, the possibility of applying quantum chemical methods to many types of problems has become readily available even for non-experts. When performing mechanistic studies, there is quite often a considerable synergy effect when combining experimental and computational approaches. The methylation reactions mentioned above turned out to be an issue well suited for quantum chemical investigations. The incentive for examining the halomethane reactivity was the clear analogy to the MTH reaction system. Alkene dimerization was also a reaction readily examined with quantum chemistry. As discussed in the introduction of this thesis, polymethylbenzenes, or their cationic counterparts, are suspected to be key intermediates in the MTH reaction. It was therefore decided to investigate the intrinsic reactivity of these species in the gas-phase by employing sophisticated mass spectrometric (MS) techniques in collaboration with the MS group at the Department of Chemistry, University of Oslo The data thus obtained will also be compared with results from an ongoing computational study on gas phase polymethylbenzenium reactivity. 6 papers presenting various studies are included. The titles are: 1) A Theoretical Investigation of the Methylation of Alkenes with Methanol over Acidic Zeolites. 2) A Theoretical Investigation of the

Kinetic Study on Pyrolysis of Oil Palm Frond

International Nuclear Information System (INIS)

Soon, V S Y; Chin, B L F; Lim, A C R

2016-01-01

The pyrolysis of oil palm frond is studied using thermogravimetric analysis (TGA) equipment. The present study investigates the thermal degradation behaviour and determination of the kinetic parameters such as the activation energy (E A ) and pre-exponential factor (A) values of oil palm frond under pyrolysis condition. The kinetic data is produced based on first order rate of reaction. In this study, the experiments are conducted at different heating rates of 10, 20, 30, 40 and 50 K/min in the temperature range of 323-1173 K under non-isothermal condition. Argon gas is used as an inert gas to remove any entrapment of gases in the TGA equipment. (paper)

Kinetic Studies on Ni-YSZ Composite Electrodes

DEFF Research Database (Denmark)

Njodzefon, Jean-Claude; Sudireddy, Bhaskar Reddy; Hjelm, Johan

2015-01-01

AC and DC techniques were applied to investigate the electrochemical reaction kinetics of porous composite Ni/8-mol% yttria-stabilized zirconia (Ni/8YSZ) solid oxide cell (SOC) electrodes using a novel pseudo-3-electrode cell geometry. From OCV impedance spectra an activation energy Ea of 1.13 e......V, prefactor yan of 3.7·105·T, hydrogen and steam partial pressure dependencies a and b respectively of -0.07 and 0.22 were determined. DC current density vs. overpotential curves compared with those predicted using the determined kinetic parameters. Apparent Butler-Volmer charge transfer coefficients α were...... branch and the need for different α values for each branch suggests that a simple BV model of the measured electrode kinetics is insufficient and/or different reaction mechanisms might be occurring in anodic vs cathodic polarization....

Kinetics of two simultaneous second-order reactions occurring in different zones

International Nuclear Information System (INIS)

Dole, M.; Hsu, C.S.; Patel, V.M.; Patel, G.N.

1975-01-01

Equations have been derived for the case of free radicals recombining according to the second-order kinetics with or without diffusion control under the conditions that there are two simultaneous spatially separated recombination reactions but that only the overall free-radical concentration can be observed. The properties of these equations are discussed and methods for determining the three independent parameters in the first case and five in the second developed. The resulting equations have been applied to the interpretation of data obtained in studying the decay of allyl chain free radicals in irradiated extended chain crystalline polyethylene

A kinetic model for chemical reactions without barriers: transport coefficients and eigenmodes

International Nuclear Information System (INIS)

Alves, Giselle M; Kremer, Gilberto M; Marques, Wilson Jr; Soares, Ana Jacinta

2011-01-01

The kinetic model of the Boltzmann equation proposed in the work of Kremer and Soares 2009 for a binary mixture undergoing chemical reactions of symmetric type which occur without activation energy is revisited here, with the aim of investigating in detail the transport properties of the reactive mixture and the influence of the reaction process on the transport coefficients. Accordingly, the non-equilibrium solutions of the Boltzmann equations are determined through an expansion in Sonine polynomials up to the first order, using the Chapman–Enskog method, in a chemical regime for which the reaction process is close to its final equilibrium state. The non-equilibrium deviations are explicitly calculated for what concerns the thermal–diffusion ratio and coefficients of shear viscosity, diffusion and thermal conductivity. The theoretical and formal analysis developed in the present paper is complemented with some numerical simulations performed for different concentrations of reactants and products of the reaction as well as for both exothermic and endothermic chemical processes. The results reveal that chemical reactions without energy barrier can induce an appreciable influence on the transport properties of the mixture. Oppositely to the case of reactions with activation energy, the coefficients of shear viscosity and thermal conductivity become larger than those of an inert mixture when the reactions are exothermic. An application of the non-barrier model and its detailed transport picture are included in this paper, in order to investigate the dynamics of the local perturbations on the constituent number densities, and velocity and temperature of the whole mixture, induced by spontaneous internal fluctuations. It is shown that for the longitudinal disturbances there exist two hydrodynamic sound modes, one purely diffusive hydrodynamic mode and one kinetic mode

A kinetic model for chemical reactions without barriers: transport coefficients and eigenmodes

Science.gov (United States)

Alves, Giselle M.; Kremer, Gilberto M.; Marques, Wilson, Jr.; Jacinta Soares, Ana

2011-03-01

The kinetic model of the Boltzmann equation proposed in the work of Kremer and Soares 2009 for a binary mixture undergoing chemical reactions of symmetric type which occur without activation energy is revisited here, with the aim of investigating in detail the transport properties of the reactive mixture and the influence of the reaction process on the transport coefficients. Accordingly, the non-equilibrium solutions of the Boltzmann equations are determined through an expansion in Sonine polynomials up to the first order, using the Chapman-Enskog method, in a chemical regime for which the reaction process is close to its final equilibrium state. The non-equilibrium deviations are explicitly calculated for what concerns the thermal-diffusion ratio and coefficients of shear viscosity, diffusion and thermal conductivity. The theoretical and formal analysis developed in the present paper is complemented with some numerical simulations performed for different concentrations of reactants and products of the reaction as well as for both exothermic and endothermic chemical processes. The results reveal that chemical reactions without energy barrier can induce an appreciable influence on the transport properties of the mixture. Oppositely to the case of reactions with activation energy, the coefficients of shear viscosity and thermal conductivity become larger than those of an inert mixture when the reactions are exothermic. An application of the non-barrier model and its detailed transport picture are included in this paper, in order to investigate the dynamics of the local perturbations on the constituent number densities, and velocity and temperature of the whole mixture, induced by spontaneous internal fluctuations. It is shown that for the longitudinal disturbances there exist two hydrodynamic sound modes, one purely diffusive hydrodynamic mode and one kinetic mode.

Pre-steady-state kinetics of Escherichia coli aspartate aminotransferase catalyzed reactions and thermodynamic aspects of its substrate specificity

International Nuclear Information System (INIS)

Kuramitsu, Seiki; Hiromi, Keitaro; Hayashi, Hideyuki; Morino, Yoshimasa; Kagamiyama, Hiroyuki

1990-01-01

The four half-transamination reactions [the pyridoxal form of Escherichia coli aspartate aminotransferase (AspAT) with aspartate or glutamate and the pyridoxamine form of the enzyme with oxalacetate or 2-oxoglutarate] were followed in a stopped-flow spectrometer by monitoring the absorbance change at either 333 or 358 nm. The reaction progress curves in all cases gave fits to a monophasic exponential process. Kinetic analyses of these reactions showed that each half-reaction is composed of the following three processes: (1) the rapid binding of an amino acid substrate to the pyridoxal form of the enzyme; (2) the rapid binding of the corresponding keto acid to the pyridoxamine form of the enzyme; (3) the rate-determining interconversion between the two complexes. This mechanism was supported by the findings that the equilibrium constants for half- and overall-transamination reactions and the steady-state kinetic constants agreed well with the predicted values on the basis of the above mechanism using pre-steady-state kinetic parameters. The significant primary kinetic isotope effect observed in the reaction with deuterated amino acid suggests that the withdrawal of the α-proton of the substrates is rate determining. The pyridoxal form of E. coli AspAT reacted with a variety of amino acids as substrates. The substrate specificity of the E. coli enzyme was much broader than that of pig isoenzymes, reflecting some subtle but distinct difference in microenvironment accommodating the side chain of the substrate between e. coli and mammalian AspATs

Kinetics and mechanism of oxygen reduction reaction at CoPd system synthesized on XC72

International Nuclear Information System (INIS)

Tarasevich, M.R.; Chalykh, A.E.; Bogdanovskaya, V.A.; Kuznetsova, L.N.; Kapustina, N.A.; Efremov, B.N.; Ehrenburg, M.R.; Reznikova, L.A.

2006-01-01

Studies are presented of the kinetics and mechanism of oxygen electroreduction reaction on CoPd catalysts synthesized on carbon black XC72. As shown both in model conditions and in the tests within the cathodes of hydrogen-oxygen fuel cells with proton conducting electrolyte, CoPd/C system features a higher activity, as compared to Co/C. The highest activity in the oxygen reduction reaction is demonstrated by the catalysts with the Pd:Co atomic ratio being 7:3 and 4:1. The structural studies (XPS and XRD, and also the data of CO desorption measurements) evidence the CoPd alloy formation, which is reflected in the negative shift of the bonding energy maximum as compared to Pd/C and in the appearance of the additional CO desorption maximums on the voltammograms. It is found by means of structural research that CoPd alloy is formed in the course of the catalyst synthesis which features a higher catalytic activity of the binary systems. Besides, CoPd/C catalyst is more stable in respect to corrosion than Pd supported on carbon black. The measurements on the rotating disc electrode and rotating ring-disc electrode evidence that CoPd/C system provides the predominant oxygen reduction to water in the practically important range of potentials (E > 0.7 V). The proximity of kinetic parameters of the oxygen reduction reaction on CoPd/C and Pt/C catalysts points to the similar reaction mechanism. The slow step of the reaction is the addition of the first electron to the adsorbed and previously protonated O 2 molecule. The assumptions are offered about the reasons causing the higher activity and selectivity of the binary catalyst towards oxygen reduction to water, as compared to Co/C. The studies of the most active catalysts within the fuel cell cathodes are performed

A Detailed Chemical Kinetic Reaction Mechanism for Oxidation of Four Small Alkyl Esters in Laminar Premixed Flames

Energy Technology Data Exchange (ETDEWEB)

Westbrook, C K; Pitz, W J; Westmoreland, P R; Dryer, F L; Chaos, M; Osswald, P; Kohse-Hoinghaus, K; Cool, T A; Wang, J; Yang, B; Hansen, N; Kasper, T

2008-02-08

A detailed chemical kinetic reaction mechanism has been developed for a group of four small alkyl ester fuels, consisting of methyl formate, methyl acetate, ethyl formate and ethyl acetate. This mechanism is validated by comparisons between computed results and recently measured intermediate species mole fractions in fuel-rich, low pressure, premixed laminar flames. The model development employs a principle of similarity of functional groups in constraining the H atom abstraction and unimolecular decomposition reactions in each of these fuels. As a result, the reaction mechanism and formalism for mechanism development are suitable for extension to larger oxygenated hydrocarbon fuels, together with an improved kinetic understanding of the structure and chemical kinetics of alkyl ester fuels that can be extended to biodiesel fuels. Variations in concentrations of intermediate species levels in these flames are traced to differences in the molecular structure of the fuel molecules.

Kinetic Modeling of the Reaction Rate for Quartz and Carbon Pellet

Science.gov (United States)

Li, Fei; Tangstad, Merete

2018-04-01

Kinetic modeling of quartz and carbon pellet at temperatures of 1898 K, 1923 K, and 1948 K (1625 °C, 1650 °C, and 1675 °C) was investigated in this study. The carbon materials used were charcoal, coke, coal, and preheated coal. The overall SiC producing reaction can be described by the reaction SiO2 + 3C = SiC + 2CO. In the SiC-producing step, the reaction rate of quartz and carbon pellet can be expressed as {d{ pct}}/dt = ( {1 - 0.40 × X_{fix - C}^{ - 0.86} × FC × {pct}} ) × A × \\exp ( { - E/{{RT}}} ) The carbon factor F C was used to describe the influence of different carbon materials that effect the gas-solid interface reaction. For charcoal, coke, coal, and preheated coal, the F C values were 0.83, 0.80, 0.94, and 0.83, respectively. The pre-exponential factor A values for the preceding four carbon materials were 1.06 × 1016 min-1, 4.21 × 1015 min-1, 3.85 × 109 min-1, and 1.00 × 1025 min-1, respectively. The activation energies E for the SiC-producing step were 570, 563, 336, and 913 kJ/mole for charcoal, coke, coal, and preheated coal pellets, respectively.

Kinetic mechanism for modeling of electrochemical reactions.

Science.gov (United States)

Cervenka, Petr; Hrdlička, Jiří; Přibyl, Michal; Snita, Dalimil

2012-04-01

We propose a kinetic mechanism of electrochemical interactions. We assume fast formation and recombination of electron donors D- and acceptors A+ on electrode surfaces. These mediators are continuously formed in the electrode matter by thermal fluctuations. The mediators D- and A+, chemically equivalent to the electrode metal, enter electrochemical interactions on the electrode surfaces. Electrochemical dynamics and current-voltage characteristics of a selected electrochemical system are studied. Our results are in good qualitative agreement with those given by the classical Butler-Volmer kinetics. The proposed model can be used to study fast electrochemical processes in microsystems and nanosystems that are often out of the thermal equilibrium. Moreover, the kinetic mechanism operates only with the surface concentrations of chemical reactants and local electric potentials, which facilitates the study of electrochemical systems with indefinable bulk.

Investigation of the kinetic mechanism of the demanganization reaction between carbon-saturated liquid iron and CaF2-CaO-SiO2-based slags

Science.gov (United States)

Duan, Sheng-chao; Li, Chuang; Guo, Han-jie; Guo, Jing; Han, Shao-wei; Yang, Wen-sheng

2018-04-01

The demanganization reaction kinetics of carbon-saturated liquid iron with an eight-component slag consisting of CaO-SiO2-MgO-FeO-MnO-Al2O3-TiO2-CaF2 was investigated at 1553, 1623, and 1673 K in this study. The rate-controlling step (RCS) for the demanganization reaction with regard to the hot metal pretreatment conditions was studied via kinetics analysis based on the fundamental equation of heterogeneous reaction kinetics. From the temperature dependence of the mass transfer coefficient of a transition-metal oxide (MnO), the apparent activation energy of the demanganization reaction was estimated to be 189.46 kJ·mol-1 in the current study, which indicated that the mass transfer of MnO in the molten slag controlled the overall rate of the demanganization reaction. The calculated apparent activation energy was slightly lower than the values reported in the literature for mass transfer in a slag phase. This difference was attributed to an increase in the "specific reaction interface" (SRI) value, either as a result of turbulence at the reaction interface or a decrease of the absolute amount of slag phase during sampling, and to the addition of calcium fluoride to the slag.

Lipase-catalyzed synthesis of palmitanilide: Kinetic model and antimicrobial activity study.

Science.gov (United States)

Liu, Kuan-Miao; Liu, Kuan-Ju

2016-01-01

Enzymatic syntheses of fatty acid anilides are important owing to their wide range of industrial applications in detergents, shampoo, cosmetics, and surfactant formulations. The amidation reaction of Mucor miehei lipase Lipozyme IM20 was investigated for direct amidation of triacylglycerol in organic solvents. The process parameters (reaction temperature, substrate molar ratio, enzyme amount) were optimized to achieve the highest yield of anilide. The maximum yield of palmitanilide (88.9%) was achieved after 24 h of reaction at 40 °C at an enzyme concentration of 1.4% (70 mg). Kinetics of lipase-catalyzed amidation of aniline with tripalmitin has been investigated. The reaction rate could be described in terms of the Michaelis-Menten equation with a Ping-Pong Bi-Bi mechanism and competitive inhibition by both the substrates. The kinetic constants were estimated by using non-linear regression method using enzyme kinetic modules. The enzyme operational stability study showed that Lipozyme IM20 retained 38.1% of the initial activity for the synthesis of palmitanilide (even after repeated use for 48 h). Palmitanilide, a fatty acid amide, exhibited potent antimicrobial activity toward Bacillus cereus. Copyright © 2015 Elsevier Inc. All rights reserved.

SUPECA kinetics for scaling redox reactions in networks of mixed substrates and consumers and an example application to aerobic soil respiration

Science.gov (United States)

Tang, Jin-Yun; Riley, William J.

2017-09-01

Several land biogeochemical models used for studying carbon-climate feedbacks have begun explicitly representing microbial dynamics. However, to our knowledge, there has been no theoretical work on how to achieve a consistent scaling of the complex biogeochemical reactions from microbial individuals to populations, communities, and interactions with plants and mineral soils. We focus here on developing a mathematical formulation of the substrate-consumer relationships for consumer-mediated redox reactions of the form A + BE→ products, where products could be, e.g., microbial biomass or bioproducts. Under the quasi-steady-state approximation, these substrate-consumer relationships can be formulated as the computationally difficult full equilibrium chemistry problem or approximated analytically with the dual Monod (DM) or synthesizing unit (SU) kinetics. We find that DM kinetics is scaling inconsistently for reaction networks because (1) substrate limitations are not considered, (2) contradictory assumptions are made regarding the substrate processing rate when transitioning from single- to multi-substrate redox reactions, and (3) the product generation rate cannot be scaled from one to multiple substrates. In contrast, SU kinetics consistently scales the product generation rate from one to multiple substrates but predicts unrealistic results as consumer abundances reach large values with respect to their substrates. We attribute this deficit to SU's failure to incorporate substrate limitation in its derivation. To address these issues, we propose SUPECA (SU plus the equilibrium chemistry approximation - ECA) kinetics, which consistently imposes substrate and consumer mass balance constraints. We show that SUPECA kinetics satisfies the partition principle, i.e., scaling invariance across a network of an arbitrary number of reactions (e.g., as in Newton's law of motion and Dalton's law of partial pressures). We tested SUPECA kinetics with the equilibrium chemistry

Kinetic Studies of Catalytic Oxidation of Cyclohexene Using ...

African Journals Online (AJOL)

Cyclohexene was oxidized using chromium (VI) oxide (CrO3) in pure acetic acid medium. The products of oxidation were analysed using simple qualitative analysis, IR spectroscopy and Gas chromatography-Mass spectrometry (GC/MS). Kinetics studies were carried out to determine the order of reaction, rate constant and ...

Single-Site Palladium(II) Catalyst for Oxidative Heck Reaction: Catalytic Performance and Kinetic Investigations

Energy Technology Data Exchange (ETDEWEB)

Duan, Hui; Li, Mengyang; Zhang, Guanghui; Gallagher, James R.; Huang, Zhiliang; Sun, Yu; Luo, Zhong; Chen, Hongzhong; Miller, Jeffrey T.; Zou, Ruqiang; Lei, Aiwen; Zhao, Yanli

2015-01-01

ABSTRACT: The development of organometallic single-site catalysts (SSCs) has inspired the designs of new heterogeneous catalysts with high efficiency. Nevertheless, the application of SSCs in certain modern organic reactions, such as C-C bond formation reactions, has still been less investigated. In this study, a single-site Pd(II) catalyst was developed, where 2,2'-bipyridine-grafted periodic mesoporous organosilica (PMO) was employed as the support of a Pd(II) complex. The overall performance of the single-site Pd(II) catalyst in the oxidative Heck reaction was then investigated. The investigation results show that the catalyst displays over 99% selectivity for the product formation with high reaction yield. Kinetic profiles further confirm its high catalytic efficiency, showing that the rate constant is nearly 40 times higher than that for the free Pd(II) salt. X-ray absorption spectroscopy reveals that the catalyst has remarkable lifetime and recyclability.

Material Balance And Reaction Kinetics Modeling For Penex Isomerization Process In Daura Refinery

Directory of Open Access Journals (Sweden)

Hamadi Adel Sharif

2017-01-01

Full Text Available Penex Deisohexanizer isomerization of light straight run naphtha is a significant process for petroleum refining and proved to be effective technology to produce gasoline components with a high octane number. Modeling of the chemical kinetic reactions is an important tool because it is a better tool for optimization of the experimental data into parameters used for industrial reactors. The present study deals on the isomerization process in Daura refinery. Material balance calculations were done mathematically on the unit for the kinetics prediction purpose. A kinetic mathematical model was derived for the prediction rate constants K1 and K2 and activation energy Ea at operating temperatures range 120-180°C. According to the model, the results show that with increasing of temperature leads to increased K1 directly, where the K2 values proportional inversely. The activation energy results show that Ea1(nC6

Kinetics of the reaction between H· and superheated water probed with muonium

International Nuclear Information System (INIS)

Alcorn, Chris D.; Brodovitch, Jean-Claude; Percival, Paul W.; Smith, Marisa; Ghandi, Khashayar

2014-01-01

Highlights: • Rate constants for reactions of H with water resolve a controversy. • H reacts with superheated water via two channels. • The findings have important implications for the safety of some nuclear power reactors. - Abstract: Safe operation of supercritical water-cooled reactors requires knowledge of the kinetics of transient species formed by the radiolysis of water in the range 300–650 °C. Using muonium, it is possible to study aqueous H · atom chemistry over this temperature range. An important reaction to study is that of the H · atom with water itself, because it is a potential source of molecular H 2 . The concentration of H 2 is important to plant coolant chemistry, as H 2 is currently added to suppress oxidative corrosion in CANDU reactors. The reaction of muonium with H 2 O and D 2 O was studied experimentally up to 450 °C, and also via quantum chemical computations to investigate possible isotope effects. Our results suggest that although the H · atom abstraction from H 2 O is important at temperatures above 300 °C, the electron-producing channel (H · + H 2 O ⇌ H 3 O + + e aq - ) is significant at temperatures up to 300 °C, and becomes the dominant reaction channel at lower temperatures

Aspartate aminotransferase: the kinetic barriers facing the covalent intermediates on the reaction pathway

International Nuclear Information System (INIS)

Kirsch, J.F.; Julin, D.A.; McLeish, M.; Wiesinger, H.

1986-01-01

The intermediates, aldimine (A), quinonoid (Q) and ketimine (K), along the transaminase reaction coordinate were probed by isotope transfer and solvent exchange kinetics. Less than 0.003% of 3 H is transferred from C/sub α/[ 3 H]-aspartate to pyridoxamine phosphate in the cytoplasmic aspartate aminotransferase (cAATase) reaction implying either that Q does not exist as a kinetically competent intermediate or that there is a rapid exchange of isotope with solvent. The ratio of the rate constants for C/sub α/ hydrogen exchange vs keto acid product formation (k/sub exge//k/sub prod/) are 2.5 and 0.5 for the reactions of cAATase with C/sub α/ [ 2 H]-aspartate and mitochondrial (m) AATase with C/sub α/[ 2 H]-glutamate respectively. The latter reaction was also probed from the α-keto-glutarate side with carbonyl 0-18 enriched keto acid. This experiment gave k/sub exge//k/sub prod/ = 1.0 for oxygen-18 exchange in α-ketoglutarate versus amino acid formation. The two exchange experiments with mAATase are interpreted in terms of a model in which the rate constant for diffusion of water from the active site is comparable with those for product forming steps

Kinetics study of levulinic acid production from corncobs by tin tetrachloride as catalyst.

Science.gov (United States)

Qing, Qing; Guo, Qi; Wang, Pengbo; Qian, Hongjia; Gao, Xiaohang; Zhang, Yue

2018-07-01

Levulinic acid (LA) is an ideal platform chemical that can be produced through acid-catalyzed dehydration and hydrolysis of hexose sugars obtained from lignocellulosic materials. In this study, SnCl 4 was identified as an efficient catalyst for LA production and the reaction kinetics was investigated in a single water phase under different reaction conditions. The Box-Behnken design response surface methodology (RSM) was applied to determine the optimized reaction conditions and three individual variables including reaction temperature, duration, and catalyst concentration were evaluated. An appealing LA yield of 76.0% was achieved at 193 °C and 17 min with 82 mM SnCl 4 catalyst. A kinetics model was developed to predict the yields of glucose, HMF, and LA, which are tally with the experimental results. The analysis of the related kinetic parameters and the results of the RSM experiment helped to provide insights into the interplay between various reaction steps with SnCl 4 as catalysts. Copyright © 2018 Elsevier Ltd. All rights reserved.

Surface Reaction Kinetics of Ga(1-x)In(x)P Growth During Pulsed Chemical Beam Epitaxy

National Research Council Canada - National Science Library

Dietz, N; Beeler, S. C; Schmidt, J. W; Tran, H. T

2000-01-01

... into the surface reaction kinetics during an organometallic deposition process. These insights will allow us to move the control point closer to the point where the growth occurs, which in a chemical been epitaxy process is a surface reaction layer (SRL...

Synchronous parallel kinetic Monte Carlo for continuum diffusion-reaction systems

International Nuclear Information System (INIS)

Martinez, E.; Marian, J.; Kalos, M.H.; Perlado, J.M.

2008-01-01

A novel parallel kinetic Monte Carlo (kMC) algorithm formulated on the basis of perfect time synchronicity is presented. The algorithm is intended as a generalization of the standard n-fold kMC method, and is trivially implemented in parallel architectures. In its present form, the algorithm is not rigorous in the sense that boundary conflicts are ignored. We demonstrate, however, that, in their absence, or if they were correctly accounted for, our algorithm solves the same master equation as the serial method. We test the validity and parallel performance of the method by solving several pure diffusion problems (i.e. with no particle interactions) with known analytical solution. We also study diffusion-reaction systems with known asymptotic behavior and find that, for large systems with interaction radii smaller than the typical diffusion length, boundary conflicts are negligible and do not affect the global kinetic evolution, which is seen to agree with the expected analytical behavior. Our method is a controlled approximation in the sense that the error incurred by ignoring boundary conflicts can be quantified intrinsically, during the course of a simulation, and decreased arbitrarily (controlled) by modifying a few problem-dependent simulation parameters

Theoretical study on the mechanism and kinetics of the reaction of 2,2‧,4,4‧-tetrabrominated diphenyl ether (BDE-47) with OH radicals

Science.gov (United States)

Cao, Haijie; He, Maoxia; Han, Dandan; Sun, Yanhui; Xie, Ju

2011-03-01

The mechanism and kinetic properties of OH-initiated gas-phase reaction of 2,2',4,4'-tetrabrominated diphenyl ether (BDE-47) have been studied at the MPWB1K/6-311 + G(3df,2p)//MPWB1K/6-31G(d) level of theory. Two types of reactions including hydroxyl addition and hydrogen abstraction have been considered. The calculation results indicate that addition reactions except for the bromo-substituted addition reaction have lower energy barriers than hydrogen abstraction reactions. Hydroxyl radical is most likely to be added to non-substituted C atoms (C(3), C(5), and C(6) atoms). Moreover, for all the reactions with OH radical, the bromo-substituted C atoms encountered the highest barrier compared to that of the rest C atoms. The rate constants and product branching ratios of each pathway have been deduced over a wide range of 200-1000 K using canonical variational transition state (CVT) theory with small curvature tunneling (SCT) contribution. This study can be regarded as an attempt to investigate the OH-initiated photochemical reaction mechanism of polybrominated diphenyl ethers (PBDEs).

Kinetics of liquid lithium reaction with oxygen-nitrogen mixtures

International Nuclear Information System (INIS)

Gil, T.K.; Kazimi, M.S.

1986-01-01

A series of experiments have been conducted in order to characterize the kinetics of lithium chemical reaction with a mixture of oxygen and nitrogen. Three mixed gas compositions were used; 80% N 2 and 20% O 2 , 90% N 2 and 10% O 2 , and 95% N 2 and 5% O 2 . The reaction rate was obtained as a function of lithium temperature and the oxygen fraction. Liquid lithium temperature varied from 400 to 1100 0 C. By varying the composition, the degree of inhibition of the lithium-nitrogen reaction rate due to the presence of oxygen was observed. The results indicate that the lithium-nitrogen reaction rate depended on both the fraction of oxygen present and lithium temperature. The lithium nitride layer formed from the reaction also had a significant inhibition effect on the lithium-nitrogen reaction rate while the lithium-oxygen reaction rate was not as greatly hindered. LITFIRE, a computer code which simulates temperature and pressure history in a containment building following lithium spills, was modified by including (1) an improved model for the lithium-nitrogen reaction rate and (2) a model for the lithium-CO 2 reaction. LITFIRE was used to simulate HEDL's LC-2 and LA-5 experiments, and the predicted temperatures and pressures were in a reasonable agreement. Furthermore, LITFIRE was applied to a prototypical fusion reactor containment in order to simulate the consequences of a lithium spill accident. The result indicated that if nitrogen was used as containment building gas during the accident, the consequences of the accident would be less severe than those with air. The pressure rise in the building was found to be reduced by 50% and the maximum temperature of the combustion zone was limited to 900 0 C instead of 1200 0 C in the case of air

Reaction kinetics and transformation of carbadox and structurally related compounds with aqueous chlorine.

Science.gov (United States)

Shah, Amisha D; Kim, Jae-Hong; Huang, Ching-Hua

2006-12-01

The potential release of carbadox (CDX), a commonly used antibacterial agent in swine husbandry, into water systems is of a concern due to its carcinogenic and genotoxic effects. Until this study, the reactivity of carbadox (possessing quinoxaline N,N'-dioxide and hydrazone moieties) toward aqueous chlorine has yetto be investigated in depth. Chemical reactivity, reaction kinetics, and transformation pathways of carbadox and structurally related compounds with free chlorine under typical water treatment conditions were determined. This study found that only CDX and desoxycarbadox (DCDX), a main metabolite of CDX with no ring N-oxide groups, react rapidly with free chlorine while other structurally related compounds including olaquindox, quindoxin, quinoxaline N-oxide, quinoxaline, and quinoline N-oxide do not. The reaction kinetics of CDX and DCDX with chlorine are highly pH dependent (e.g., the apparent second-order rate constant, kapp, for CDX ranges from 51.8 to 3.15 x 10(4) M(-1)s(-1) at pH 4-11). The high reactivity of CDX and DCDX to chlorine involves deprotonation of their hydrazone N-H moieties where initial chlorine attack results in a reactive intermediate that is further attacked by nucleophiles in the matrix to yield non-chlorinated, hydroxylated, and larger molecular weight byproducts. All of the CDX's byproducts retain their biologically active N-oxide groups, suggesting that they may remain as active antibacterial agents.

Reaction kinetic model of the surface-mediated formation of PCDD/F from pyrolysis of 2-chlorophenol on a CuP/Silica suface

Energy Technology Data Exchange (ETDEWEB)

Lomnicki, S.; Khachatryan, L.; Dellinger, B. [Louisiana State Univ., Baton Rouge (United States). Dept. of Chemistry

2004-09-15

One of the major challenges in developing predictive models of the surface mediated pollutant formation and fuel combustion is the construction of reliable reaction kinetic mechanisms and models. While the homogeneous, gas-phase chemistry of various light fuels such as hydrogen and methane is relatively well-known large uncertainties exist in the reaction paths of surface mediated reaction mechanisms for even these very simple species. To date, no detailed kinetic consideration of the surface mechanisms of formation of complex organics such as PCDD/F have been developed. In addition to the complexity of the mechanism, a major difficulty is the lack of reaction kinetic parameters (pre-exponential factor and activation energy) of surface reactions, Consequently, numerical studies of the surface-mediated formation of PCDD/F have often been incorporated only a few reactions. We report the development of a numerical multiple-step surface model based on experimental data of surface mediated (5% CuO/SiO2) conversion of 2-monochlorphenol (2-MCP) to PCDD/F under pyrolytic or oxidative conditions. A reaction kinetic model of the catalytic conversion of 2-MCP on the copper oxide catalyst under pyrolytic conditions was developed based on a detailed multistep surface reaction mechanism developed in our laboratory. The performance of the chemical model is assessed by comparing the numerical predictions with experimental measurements. SURFACE CHEMKIN (version 3.7.1) software was used for modeling. Our results confirm the validity of previously published mechanism of the reaction and provides new insight concerning the formation of PCDD/F formation in combustion processes. This model successfully explains the high yields of PCDD/F at low temperatures that cannot be explained using a purely gas-phase mode.

Noise-induced modulation of the relaxation kinetics around a non-equilibrium steady state of non-linear chemical reaction networks.

Science.gov (United States)

Ramaswamy, Rajesh; Sbalzarini, Ivo F; González-Segredo, Nélido

2011-01-28

Stochastic effects from correlated noise non-trivially modulate the kinetics of non-linear chemical reaction networks. This is especially important in systems where reactions are confined to small volumes and reactants are delivered in bursts. We characterise how the two noise sources confinement and burst modulate the relaxation kinetics of a non-linear reaction network around a non-equilibrium steady state. We find that the lifetimes of species change with burst input and confinement. Confinement increases the lifetimes of all species that are involved in any non-linear reaction as a reactant. Burst monotonically increases or decreases lifetimes. Competition between burst-induced and confinement-induced modulation may hence lead to a non-monotonic modulation. We quantify lifetime as the integral of the time autocorrelation function (ACF) of concentration fluctuations around a non-equilibrium steady state of the reaction network. Furthermore, we look at the first and second derivatives of the ACF, each of which is affected in opposite ways by burst and confinement. This allows discriminating between these two noise sources. We analytically derive the ACF from the linear Fokker-Planck approximation of the chemical master equation in order to establish a baseline for the burst-induced modulation at low confinement. Effects of higher confinement are then studied using a partial-propensity stochastic simulation algorithm. The results presented here may help understand the mechanisms that deviate stochastic kinetics from its deterministic counterpart. In addition, they may be instrumental when using fluorescence-lifetime imaging microscopy (FLIM) or fluorescence-correlation spectroscopy (FCS) to measure confinement and burst in systems with known reaction rates, or, alternatively, to correct for the effects of confinement and burst when experimentally measuring reaction rates.

Pyrolysis of Waste Castor Seed Cake: A Thermo-Kinetics Study

Directory of Open Access Journals (Sweden)

Abdullahi Muhammad Sokoto

2018-03-01

Full Text Available Biomass pyrolysis is a thermo-chemical conversion process that is of both industrial and ecological importance. The efficient chemical transformation of waste biomass to numerous products via pyrolysis reactions depends on process kinetic rates; hence the need for kinetic models to best design and operate the pyrolysis. Also, for an efficient design of an environmentally sustainable pyrolysis process of a specific lignocellulosic waste, a proper understanding of its thermo-kinetic behavior is imperative. Thus, pyrolysis kinetics of castor seed de-oiled cake (Ricinus communis using thermogravimetric technique was studied. The decomposition of the cake was carried out in a nitrogen atmosphere with a flow rate of 100mL min-1 from ambient temperature to 900 °C. The results of the thermal profile showed moisture removal and devolatilization stages, and maximum decomposition of the cake occurred at a temperature of 200-400 °C. The kinetic parameters such as apparent activation energy, pre-exponential factor, and order of reaction were determined using Friedman (FD, Kissinger-Akahira-Sunose (KAS, and Flynn-Wall-Ozawa (FWO kinetic models. The average apparent activation energy values of 124.61, 126.95 and 129.80 kJmol-1 were calculated from the slopes of the respective models. The apparent activation energy values obtained depends on conversion, which is an evidence of multi-step kinetic process during the pyrolytic decomposition of the cake. The kinetic data would be of immense benefit to model, design and develop a suitable thermo-chemical system for the conversion of waste de-oil cake to energy carrier.

A kinetic-theory approach for computing chemical-reaction rates in upper-atmosphere hypersonic flows.

Science.gov (United States)

Gallis, Michael A; Bond, Ryan B; Torczynski, John R

2009-09-28

Recently proposed molecular-level chemistry models that predict equilibrium and nonequilibrium reaction rates using only kinetic theory and fundamental molecular properties (i.e., no macroscopic reaction-rate information) are investigated for chemical reactions occurring in upper-atmosphere hypersonic flows. The new models are in good agreement with the measured Arrhenius rates for near-equilibrium conditions and with both measured rates and other theoretical models for far-from-equilibrium conditions. Additionally, the new models are applied to representative combustion and ionization reactions and are in good agreement with available measurements and theoretical models. Thus, molecular-level chemistry modeling provides an accurate method for predicting equilibrium and nonequilibrium chemical-reaction rates in gases.

Atmospheric chemistry of CF3COOH. Kinetics of the reaction with OH radicals

DEFF Research Database (Denmark)

Møgelberg, T.E.; Nielsen, O.J.; Sehested, J.

1994-01-01

Two different experimental techniques were used to study the kinetics of the reaction of OH radicals with trifluoroacetic acid, CF3COOH. Using a pulse radiolysis absolute rate technique, rate constants at 315 and 348 K were determined to be (1.6 +/- 0.4) x 10(-13) and (1.5 +/- 0.2) x 10(-13) cm3...... molecule-1 s-1, respectively. Using a long path-length FTIR relative rate technique a rate constant of (1.7 +/- 0.5) x 10(-13) cm3 molecule-1 s-1 was obtained at 296 K. In the atmosphere, reaction with OH radicals in the gas phase is estimated to account for 10%-20% of the loss of CF3COOH. The major fate...

Experimental study o the sodium-concrete reaction

International Nuclear Information System (INIS)

Goncalves, A.C.; Torres, A.R.; Brito Aghina, L.O. de; Messere e Castro, P.

1986-01-01

Effects and aspects of security are verified during a sodium leakage in high temperatures on liners of contention cells and directly on the concrete. As this kinetic process involves reactions between materials in solid state (such as oxides and carbonates) vapors and gases (such as water and CO 2 )) with liquid sodium, effects of each phase of the heterogeneous mixture are separately analysed. Are still analysed produced products and briefly discussed the kinetic of the sodium-concrete reaction. (Author) [pt

Thermodynamic and kinetic analysis of the reaction between biological catecholamines and chlorinated methylperoxy radicals

Science.gov (United States)

Dimić, Dušan S.; Milenković, Dejan A.; Marković, Jasmina M. Dimitrić; Marković, Zoran S.

2018-05-01

The antiradical potency of catecholamines (dopamine, epinephrine, norepinephrine, L-DOPA), metabolites of dopamine (homovanillic acid, 3-methoxytyramine and 3,4-dihydroxyphenylacetic acid) and catechol towards substituted methylperoxy radicals is investigated. The thermodynamic parameters, together with the kinetic approach, are used to determine the most probable mechanism of action. The natural bond orbital and quantum theory of atoms in molecules are utilised to explain the highest reactivity of trichloromethylperoxy radical. The preferred mechanism is dependent both on the thermodynamic and kinetic parameters . The number of chlorine atoms on radical, the presence of intra-molecular hydrogen bond and number of hydroxy groups attached to the aromatic ring significantly influence the mechanism. The results suggest that sequential proton loss electron transfer (SPLET) is the most probable for reaction with methylperoxy and hydrogen atom transfer (HAT) for reaction with trichloromethylperoxy radicals, with a gradual transition between SPLET and HAT for other two radicals. Due to the significant deprotonation of molecules containing the carboxyl group, the respective anions are also investigated. The HAT and SPLET mechanisms are highly competitive in reaction with MP radical, while the dominant mechanism towards chlorinated radicals is HAT. The reactions in methanol and benzene are also discussed.

Golden rule kinetics of transfer reactions in condensed phase: The microscopic model of electron transfer reactions in disordered solid matrices

Energy Technology Data Exchange (ETDEWEB)

Basilevsky, M. V.; Mitina, E. A. [Photochemistry Center, Russian Academy of Sciences, 7a, Novatorov ul., Moscow (Russian Federation); Odinokov, A. V. [Photochemistry Center, Russian Academy of Sciences, 7a, Novatorov ul., Moscow (Russian Federation); National Research Nuclear University “MEPhI,” 31, Kashirskoye shosse, Moscow (Russian Federation); Titov, S. V. [Karpov Institute of Physical Chemistry, 3-1/12, Building 6, Obuha pereulok, Moscow (Russian Federation)

2013-12-21

The algorithm for a theoretical calculation of transfer reaction rates for light quantum particles (i.e., the electron and H-atom transfers) in non-polar solid matrices is formulated and justified. The mechanism postulated involves a local mode (an either intra- or inter-molecular one) serving as a mediator which accomplishes the energy exchange between the reacting high-frequency quantum mode and the phonon modes belonging to the environment. This approach uses as a background the Fermi golden rule beyond the usually applied spin-boson approximation. The dynamical treatment rests on the one-dimensional version of the standard quantum relaxation equation for the reduced density matrix, which describes the frequency fluctuation spectrum for the local mode under consideration. The temperature dependence of a reaction rate is controlled by the dimensionless parameter ξ{sub 0}=ℏω{sub 0}/k{sub B}T where ω{sub 0} is the frequency of the local mode and T is the temperature. The realization of the computational scheme is different for the high/intermediate (ξ{sub 0} < 1 − 3) and for low (ξ{sub 0}≫ 1) temperature ranges. For the first (quasi-classical) kinetic regime, the Redfield approximation to the solution of the relaxation equation proved to be sufficient and efficient in practical applications. The study of the essentially quantum-mechanical low-temperature kinetic regime in its asymptotic limit requires the implementation of the exact relaxation equation. The coherent mechanism providing a non-vanishing reaction rate has been revealed when T→ 0. An accurate computational methodology for the cross-over kinetic regime needs a further elaboration. The original model of the hopping mechanism for electronic conduction in photosensitive organic materials is considered, based on the above techniques. The electron transfer (ET) in active centers of such systems proceeds via local intra- and intermolecular modes. The active modes, as a rule, operate beyond the

Reactions of enolisable ketones with dichloroisocyanuric acid in absence and presence of added chloride ions – a kinetic study

Directory of Open Access Journals (Sweden)

Y. L. Kumar

2015-01-01

Full Text Available Kinetics of reactions of enolisable ketones (S = acetone/2-butanone with dichloroisocyanuric acid (DCICA were studied in aqueous acetic acid and perchloric acid media in absence and presence of added chloride ions. The reactions were found to be pseudo zero order and pseudo first order on [DCICA] in absence and presence of chloride ions respectively. Both in presence and absence of chloride ions, first order and fractional order in substrate and perchloric acid were observed respectively. An increase in the rate of reaction was observed with an increase in chloride ion concentration as well as acetic acid composition. The results were interpreted in terms of probable mechanisms involving (i rate-determining enol formation from the conjugate acid of the ketone (SH+ in the absence of added chloride ions and (ii rate-determining interaction of SH+ with the most effective molecular chlorine species produced by the hydrolysis of DCICA (rather than a rate-determining interaction of enol with chlorine in the presence of added chloride ions, prior to the rapid steps of product formation. DOI: http://dx.doi.org/10.4314/bcse.v29i1.12

Study on radiation grafting reaction of MMA onto hydroxyapatite

International Nuclear Information System (INIS)

Jiang Bo

1996-01-01

The grafting reaction of MMA onto hydroxyapatite has been studied with the pre-irradiation method in air. The effects of radiation dose, monomer concentration, reaction temperature and inorganic acid on the system are observed. The grafting copolymerization is found to be controlled by the kinetics. If proper kinetic conditions are selected, a better grafting yield can be obtained. Employing weight method, burning method as well as SeM and IR analysis, it has been proved that MMA is definitely grafted onto hydroxyapatite by chemical bonds, which shows that it is possible to improve the interface of inorganic-organic composite materials and to make bioactive ceramics by using radiation induced-grafting copolymerization

Quantitative modeling of the reaction/diffusion kinetics of two-chemistry photopolymers

Science.gov (United States)

Kowalski, Benjamin Andrew

Optically driven diffusion in photopolymers is an appealing material platform for a broad range of applications, in which the recorded refractive index patterns serve either as images (e.g. data storage, display holography) or as optical elements (e.g. custom GRIN components, integrated optical devices). A quantitative understanding of the reaction/diffusion kinetics is difficult to obtain directly, but is nevertheless necessary in order to fully exploit the wide array of design freedoms in these materials. A general strategy for characterizing these kinetics is proposed, in which key processes are decoupled and independently measured. This strategy enables prediction of a material's potential refractive index change, solely on the basis of its chemical components. The degree to which a material does not reach this potential reveals the fraction of monomer that has participated in unwanted reactions, reducing spatial resolution and dynamic range. This approach is demonstrated for a model material similar to commercial media, achieving quantitative predictions of index response over three orders of exposure dose (~1 to ~103 mJ cm-2) and three orders of feature size (0.35 to 500 microns). The resulting insights enable guided, rational design of new material formulations with demonstrated performance improvement.

Reaction kinetics and mechanisms of organosilicon fungicide flusilazole with sulfate and hydroxyl radicals.

Science.gov (United States)

Mercado, D Fabio; Bracco, Larisa L B; Arques, Antonio; Gonzalez, Mónica C; Caregnato, Paula

2018-01-01

Flusilazole is an organosilane fungicide used for treatments in agriculture and horticulture for control of diseases. The reaction kinetics and mechanism of flusilazole with sulfate and hydroxyl radicals were studied. The rate constant of the radicals with the fungicide were determined by laser flash photolysis of peroxodisulfate and hydrogen peroxide. The results were 2.0 × 10 9 s -1 M -1 for the reaction of the fungicide with HO and 4.6 × 10 8  s -1  M -1 for the same reaction with SO 4 - radicals. The absorption spectra of organic intermediates detected by laser flash photolysis of S 2 O 8 2- with flusilazole, were identified as α-aminoalkyl and siloxyl radicals and agree very well with those estimated employing the time-dependent density functional theory with explicit account for bulk solvent effects. In the continuous photolysis experiments, performed by photo-Fenton reaction of the fungicide, the main degradation products were: (bis(4-fluorophenyl)-hydroxy-methylsilane) and the non-toxic silicic acid, diethyl bis(trimethylsilyl) ester, in ten and twenty minutes of reaction, respectively. Copyright © 2017. Published by Elsevier Ltd.

alfa-Deuterium kinetic isotope effects in reactions of methyllithium. Is better aggregation the cause of lower reactivity?

DEFF Research Database (Denmark)

Holm, Torkil

1996-01-01

The value of kH/kD for alfa deuterium kinetic isotope effects for the reaction of methyllithium and methylmagnesium iodid with a series of substrates are consistently ca. 10-15 % higher for the lithium reagent. This may indicate a pre-equilibrium......The value of kH/kD for alfa deuterium kinetic isotope effects for the reaction of methyllithium and methylmagnesium iodid with a series of substrates are consistently ca. 10-15 % higher for the lithium reagent. This may indicate a pre-equilibrium...

Study on the Hydrolysis Kinetics of Xylan on Different Acid Catalysts

Energy Technology Data Exchange (ETDEWEB)

Na, Byeong-Il; Lee, Jae-Won [Chonnam National University, Gwangju (Korea, Republic of)

2014-04-15

In this study, we investigated kinetic model for the acid-catalyzed xylan hydrolysis at temperature 120-150 .deg. C. Also, we analyzed the kinetic parameters for xylose production and furfural decomposition. The hydrolysis of xylan and the degradation of xylose were promoted by high reaction temperature and acid concentration. The optimal hydrolysis condition for the highest reaction rate constants (k{sub 1}) was different depending on the acid catalysts. Among sulfuric, oxalic and maleic acid, the xylan reaction rate constants (k{sub 1}) to xylose had the highest value of 0.0241 min{sup -1} when 100 mM sulfuric acid was used at 120 .deg. C. However, sulfuric acid induced more xylose degradation compared to oxalic and maleic acid hydrolysis. The activation energy for xylan degradation was the highest when sulfuric acid was used.

Chemical reactions on platinum-group metal surfaces studied by synchrotron-radiation-based spectroscopy

International Nuclear Information System (INIS)

Kondoh, Hiroshi; Nakai, Ikuyo; Nagasaka, Masanari; Amemiya, Kenta; Ohta, Toshiaki

2009-01-01

A new version of synchrotron-radiation-based x-ray spectroscopy, wave-length-dispersive near-edge x-ray absorption fine structure (dispersive-NEXAFS), and fast x-ray photoelectron spectroscopy have been applied to mechanistic studies on several surface catalytic reactions on platinum-group-metal surfaces. In this review, our approach using above techniques to understand the reaction mechanism and actual application studies on three well-known catalytic surface reactions, CO oxidation on Pt(111) and Pd(111), NO reduction on Rh(111), and H 2 O formation on Pt(111), are introduced. Spectroscopic monitoring of the progress of the surface reactions enabled us to detect reaction intermediates and analyze the reaction kinetics quantitatively which provides information on reaction order, rate constant, pre-exponential factor, activation energy and etc. Such quantitative analyses combined with scanning tunneling microscopy and kinetic Monte Carlo simulations revealed significant contribution of the adsorbate configurations and their dynamic changes to the reaction mechanisms of the above fundamental catalytic surface reactions. (author)

Investigation of the kinetics of the reactions of oxidation, nitration, and hydrogenation of uranium

International Nuclear Information System (INIS)

Adda, Y.

1955-06-01

Various physico-chemical methods have been used to investigate the kinetics of the oxidation hydridation and nitridation of uranium. The experimental results show that the kinetics of these reactions are influenced by many factors also the Pilling and Bedworth rule is valid only under very limited conditions. The disagreement between this rule and the experimental results could be explained by the existence of numerous mechanical faults in the compounds obtained by the dry corrosion of the metal. (author) [fr

Kinetic study of the reaction of uranium with various carbon-containing gases; Etude cinetique de la reaction sur l'uranium de differents gaz carbones

Energy Technology Data Exchange (ETDEWEB)

Feron, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1963-09-15

The kinetic study of the reaction U + CO{sub 2} and U + CO has been performed by a thermogravimetric method on a spherical uranium powder, in temperature ranges respectively from 460 to 690 deg. C and from 570 to 850 deg. C. The reaction with carbon dioxide leads to uranium dioxide. A carbon deposition takes place at the same time. The global reactions is the result of two reactions: U + 2 CO{sub 2} {yields} UO{sub 2} + 2 CO U + CO{sub 2} {yields} UO{sub 2} + C The reaction with carbon monoxide leads to a mixture of dioxide UO{sub 2}, dicarbide UC{sub 2} and free carbon. The main reaction can be written. U + CO {yields} 1/2 UO{sub 2} + 1/2 UC{sub 2} The free carbon results of the disproportionation of the carbon monoxide. A remarkable separation of the two phases UO{sub 2} and UC{sub 2} can be observed. A mechanism accounting for the phenomenon has been proposed. The two reactions U + CO{sub 2} and U + CO begin with a long germination period, after which, the reaction velocity seems to be limited in both cases by the ionic diffusion of oxygen through the uranium dioxide. (author) [French] L'etude cinetique des reactions U sol + CO{sub 2} gaz et U sol + CO gaz a ete effectuee par thermogravirnetrie sur une poudre d'uranium a grains spheriques, les domaines de temperature etudies s'etendant respectivement de 460 a 690 deg. C et de 570 a 850 deg. C. L'action du dioxyde de carbone conduit au dioxyde d'uranium UO{sub 2}; il se produit en meme temps un depot de carbone. La reaction globale resulte des deux reactions: U + 2 CO{sub 2} {yields} UO{sub 2} + 2 CO U + CO{sub 2} {yields} UO{sub 2} + C Le mono-oxyde de carbone conduit a un melange de dioxyde UO{sub 2}, de dicarbure UC{sub 2} et de carbone libre. La reaction principale s'ecrit: U + CO {yields} 1/2 UO{sub 2} + 1/2 UC{sub 2} Le carbone libre provient de la dismutation du mono-oxyde de carbone. On observe une separation remarquable des deux phases UO{sub 2} et UC{sub 2}; un mecanisme rendant compte de ce phenomene a

Kinetics of the rapid reaction Br/sub 2/ + 2 I/sup -/. -->. I/sub 2/ + 2 Br/sup -/ in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Rao, T S; Mali, S I; Dangat, V T [Presidency Coll., Calcutta (India). Dept. of Chemistry

1979-01-01

The displacement of iodine from aqueous iodide ion solutions by bromine is a rapid reaction whose kinetics has been studied by the competition technique. The reaction is of second order, having a specific rate of 6.85 x 10/sup 5/ M/sup -1/ s/sup -1/ at 25.0 /sup 0/C and energy of activation of 30.8 kJ mol/sup -1/. A mechanism for the reaction is proposed.

Ground reaction forces and knee kinetics during single and repeated badminton lunges.

Science.gov (United States)

Lam, Wing Kai; Ding, Rui; Qu, Yi

2017-03-01

Repeated movement (RM) lunge that frequently executed in badminton might be used for footwear evaluation. This study examined the influence of single movement (SM) and RM lunges on the ground reaction forces (GRFs) and knee kinetics during the braking phase of a badminton lunge step. Thirteen male university badminton players performed left-forward lunges in both SM and RM sessions. Force platform and motion capturing system were used to measure GRFs and knee kinetics variables. Paired t-test was performed to determine any significant differences between SM and RM lunges regarding mean and coefficient of variation (CV) in each variable. The kinetics results indicated that compared to SM lunges, the RM lunges had shorter contact time and generated smaller maximum loading rate of impact force, peak knee anterior-posterior force, and peak knee sagittal moment but generated larger peak horizontal resultant forces (Ps < 0.05). Additionally, the RM lunges had lower CV for peak knee medial-lateral and vertical forces (Ps < 0.05). These results suggested that the RM testing protocols had a distinct loading response and adaptation pattern during lunge and that the RM protocol showed higher within-trial reliability, which may be beneficial for the knee joint loading evaluation under different interventions.

Kinetic isotope effect in the reaction of dehydration of fructose into 5-hydroxymethylfurfural

International Nuclear Information System (INIS)

Grin', S.A.; Tsimbaliev, S.R.; Gel'fand, S.Yu.

1993-01-01

Kinetic isotopic effect in the reaction of fructose dehydration into 5- hydroxymethylfurfural was determined. The results suggest hydrogen participation in the limiting stage of the process. The assumption that proton addition to 4, 5, 6 -trihydroxy - 2- on - hexal is the limiting stage is made

Modelling and simulation of a transketolase mediated reaction: Sensitivity analysis of kinetic parameters

DEFF Research Database (Denmark)

Sayar, N.A.; Chen, B.H.; Lye, G.J.

2009-01-01

In this paper we have used a proposed mathematical model, describing the carbon-carbon bond format ion reaction between beta-hydroxypyruvate and glycolaldehyde to synthesise L-erythrulose, catalysed by the enzyme transketolase, for the analysis of the sensitivity of the process to its kinetic...

Kinetic study of the annealing reactions in Cu-Ni-Fe alloys; Estudio cinetico de las reacciones de recocido en aleaciones de Cu-Ni-Fe

Energy Technology Data Exchange (ETDEWEB)

Donoso, E.

2014-07-01

The thermal aging of a Cu-45Ni-4Fe, Cu-34Ni-11Fe and Cu-33Ni-22Fe alloys tempered from 1173 K have been studied from Differential Scanning Calorimetry (DSC) and microhardness measurements. The analysis of DSC curves, from room temperature to 950 K, shows the presence of one exothermic reaction associated to the formation of FeNi{sub 3} phase nucleating from a modulate structure, and one endothermic peak attributed to dissolution of this phase. Kinetic parameters were obtained using the usual Avrami-Erofeev equation, modified Kissinger method and integrated kinetic functions. Microhardness measurements confirmed the formation and dissolution of the FeNi{sub 3} phase. (Author)

General theory of the multistage geminate reactions of the isolated pairs of reactants. II. Detailed balance and universal asymptotes of kinetics.

Science.gov (United States)

Kipriyanov, Alexey A; Doktorov, Alexander B

2014-10-14

The analysis of general (matrix) kinetic equations for the mean survival probabilities of any of the species in a sample (or mean concentrations) has been made for a wide class of the multistage geminate reactions of the isolated pairs. These kinetic equations (obtained in the frame of the kinetic approach based on the concept of "effective" particles in Paper I) take into account various possible elementary reactions (stages of a multistage reaction) excluding monomolecular, but including physical and chemical processes of the change in internal quantum states carried out with the isolated pairs of reactants (or isolated reactants). The general basic principles of total and detailed balance have been established. The behavior of the reacting system has been considered on macroscopic time scales, and the universal long-term kinetics has been determined.

The reaction between iodine and organic coatings under severe PWR accident conditions. An experimental parameter study

Energy Technology Data Exchange (ETDEWEB)

Hellmann, S; Funke, F; Greger, G U; Bleier, A; Morell, W [Siemens AG, Power Generation Group, Erlangen (Germany)

1996-12-01

An extensive experimental parameter study was performed on the deposition and on the resuspension kinetics in the reaction system iodine/organically coated surfaces. Both reactions in the gas phase and in the liquid phase were investigated and kinetic rate constants suitable for modelling were derived. Previous experimental studies on the reaction of iodine with organic coated surfaces were mostly limited to temperatures below 100{sup o}C. Thus, this parameter study aims at filling a gap and providing kinetic data on heterogeneous reactions with organic surfaces in the accident-relevant temperature range of 100-160{sup o}C. Two types of laboratory experiments carried out at Siemens/KWU using coatings representative for German power plants (epoxy-tape paint), namely gas phase tests and liquid phase tests. (author) 6 figs., 6 tabs., 5 refs.

The influence of gas–solid reaction kinetics in models of thermochemical heat storage under monotonic and cyclic loading

International Nuclear Information System (INIS)

Nagel, T.; Shao, H.; Roßkopf, C.; Linder, M.; Wörner, A.; Kolditz, O.

2014-01-01

Highlights: • Detailed analysis of cyclic and monotonic loading of thermochemical heat stores. • Fully coupled reactive heat and mass transport. • Reaction kinetics can be simplified in systems limited by heat transport. • Operating lines valid during monotonic and cyclic loading. • Local integral degree of conversion to capture heterogeneous material usage. - Abstract: Thermochemical reactions can be employed in heat storage devices. The choice of suitable reactive material pairs involves a thorough kinetic characterisation by, e.g., extensive thermogravimetric measurements. Before testing a material on a reactor level, simulations with models based on the Theory of Porous Media can be used to establish its suitability. The extent to which the accuracy of the kinetic model influences the results of such simulations is unknown yet fundamental to the validity of simulations based on chemical models of differing complexity. In this article we therefore compared simulation results on the reactor level based on an advanced kinetic characterisation of a calcium oxide/hydroxide system to those obtained by a simplified kinetic model. Since energy storage is often used for short term load buffering, the internal reactor behaviour is analysed under cyclic partial loading and unloading in addition to full monotonic charge/discharge operation. It was found that the predictions by both models were very similar qualitatively and quantitatively in terms of thermal power characteristics, conversion profiles, temperature output, reaction duration and pumping powers. Major differences were, however, observed for the reaction rate profiles themselves. We conclude that for systems not limited by kinetics the simplified model seems sufficient to estimate the reactor behaviour. The degree of material usage within the reactor was further shown to strongly vary under cyclic loading conditions and should be considered when designing systems for certain operating regimes

HYDROBIOGEOCHEM: A coupled model of HYDROlogic transport and mixed BIOGEOCHEMical kinetic/equilibrium reactions in saturated-unsaturated media

Energy Technology Data Exchange (ETDEWEB)

Yeh, G.T.; Salvage, K.M. [Pennsylvania State Univ., University Park, PA (United States). Dept. of Civil and Environmental Engineering; Gwo, J.P. [Oak Ridge National Lab., TN (United States); Zachara, J.M.; Szecsody, J.E. [Pacific Northwest National Lab., Richland, WA (United States)

1998-07-01

The computer program HYDROBIOGEOCHEM is a coupled model of HYDROlogic transport and BIOGEOCHEMical kinetic and/or equilibrium reactions in saturated/unsaturated media. HYDROBIOGEOCHEM iteratively solves the two-dimensional transport equations and the ordinary differential and algebraic equations of mixed biogeochemical reactions. The transport equations are solved for all aqueous chemical components and kinetically controlled aqueous species. HYDROBIOGEOCHEM is designed for generic application to reactive transport problems affected by both microbiological and geochemical reactions in subsurface media. Input to the program includes the geometry of the system, the spatial distribution of finite elements and nodes, the properties of the media, the potential chemical and microbial reactions, and the initial and boundary conditions. Output includes the spatial distribution of chemical and microbial concentrations as a function of time and space, and the chemical speciation at user-specified nodes.

Kinetics of the Reactions of IO Radicals with NO and NO2

Science.gov (United States)

Daykin, E. P.; Wine, P. H.

1997-01-01

A laser flash photolysis-long path absorption technique has been employed to study the kinetics of the reactions of IO radicals with NO and NO2 as a function of temperature and pressure. The IO and NO rate coefficient is independent of pressure over the range 40-200 Torr of N2, and its temperature dependence over the range 242-359 K is adequately described by the Arrhenius expression k(sub 1) = (6.9 +/- 1.7) x 10(exp -12) exp[(328 +/- 71)/T] cu cm/(molecule.s) (errors are 2 sigma, precision only). These Arrhenius parameters are similar to those determined previously for the ClO + NO and BrO + NO reactions. The IO and NO2 association reaction is found to be in the falloff regime over the temperature and pressure ranges investigated (254-354 K and 40-750 Torr of N2). Assuming F(sub c) = 0.4 independent of temperature, a physically reasonable set of falloff parameters which adequately describe the data are k(sub 0) = 7.7 x 10(exp -31)(T/300)(exp -5.0) cm(exp 6)/(molecule(exp 2).s) and k(sub infinity) = 1.55 x 10(exp -11)cu cm/(molecule.s) independent of temperature. The IO + NO2 rate coefficients determined in this study are about a factor of 2 faster than those reported in the only previous study of this reaction.

Kinetics of the high-temperature combustion reactions of dibutylether using composite computational methods

KAUST Repository

Rachidi, Mariam El

2015-01-01

This paper investigates the high-temperature combustion kinetics of n-dibutyl ether (n-DBE), including unimolecular decomposition, H-abstraction by H, H-migration, and C{single bond}C/C{single bond}O β-scission reactions of the DBE radicals. The energetics of H-abstraction by OH radicals is also studied. All rates are determined computationally using the CBS-QB3 and G4 composite methods in conjunction with conventional transition state theory. The B3LYP/6-311++G(2df,2pd) method is used to optimize the geometries and calculate the frequencies of all reactive species and transition states for use in ChemRate. Some of the rates calculated in this study vary markedly from those obtained for similar reactions of alcohols or alkanes, particularly those pertaining to unimolecular decomposition and β-scission at the α-β C{single bond}C bond. These variations show that analogies to alkanes and alcohols are, in some cases, inappropriate means of estimating the reaction rates of ethers. This emphasizes the need to establish valid rates through computation or experimentation. Such studies are especially important given that ethers exhibit promising biofuel and fuel additive characteristics. © 2014.

Noise-induced modulation of the relaxation kinetics around a non-equilibrium steady state of non-linear chemical reaction networks.

Directory of Open Access Journals (Sweden)

Rajesh Ramaswamy

2011-01-01

Full Text Available Stochastic effects from correlated noise non-trivially modulate the kinetics of non-linear chemical reaction networks. This is especially important in systems where reactions are confined to small volumes and reactants are delivered in bursts. We characterise how the two noise sources confinement and burst modulate the relaxation kinetics of a non-linear reaction network around a non-equilibrium steady state. We find that the lifetimes of species change with burst input and confinement. Confinement increases the lifetimes of all species that are involved in any non-linear reaction as a reactant. Burst monotonically increases or decreases lifetimes. Competition between burst-induced and confinement-induced modulation may hence lead to a non-monotonic modulation. We quantify lifetime as the integral of the time autocorrelation function (ACF of concentration fluctuations around a non-equilibrium steady state of the reaction network. Furthermore, we look at the first and second derivatives of the ACF, each of which is affected in opposite ways by burst and confinement. This allows discriminating between these two noise sources. We analytically derive the ACF from the linear Fokker-Planck approximation of the chemical master equation in order to establish a baseline for the burst-induced modulation at low confinement. Effects of higher confinement are then studied using a partial-propensity stochastic simulation algorithm. The results presented here may help understand the mechanisms that deviate stochastic kinetics from its deterministic counterpart. In addition, they may be instrumental when using fluorescence-lifetime imaging microscopy (FLIM or fluorescence-correlation spectroscopy (FCS to measure confinement and burst in systems with known reaction rates, or, alternatively, to correct for the effects of confinement and burst when experimentally measuring reaction rates.

Theoretical Study of the Kinetics of the Pyrolytic Elimination Reaction of Ethyl Chloride

Directory of Open Access Journals (Sweden)

Isaiah Ajibade Adejoro

2010-01-01

Full Text Available The products of the gas-phase elimination of ethyl chloride are hydrogen chloride and ethane. Using AM1, MNDO and PM3 Hamiltonians of quantum mechanical computer code called MOPAC, a procedure for the kinetics and computation of the Arrhenius parameters for the pyrolytic elimination reaction of ethyl chloride was devised in order to evaluate the predictive ability of the three Hamiltonians used. The first-order rate coefficient for the three Hamiltonians are 1.15x10-8s-1, 4.55x10-15s-1 and 5.36x10-4s-1 for AM1, MNDO and PM3 respectively. The results obtained showed that the rate constant for the computed Arrhenius parameters compare well with the experimental values in the literature, thus showing that the computational procedure adequately simulates experimental results; also the semi-empirical AMI calculation has the best predictive ability with experiment followed by PM3 while MNDO has the least.

Pre-steady-state kinetic studies of redox reactions catalysed by Bacillus subtilis ferredoxin-NADP(+) oxidoreductase with NADP(+)/NADPH and ferredoxin.

Science.gov (United States)

Seo, Daisuke; Soeta, Takahiro; Sakurai, Hidehiro; Sétif, Pierre; Sakurai, Takeshi

2016-06-01

Ferredoxin-NADP(+) oxidoreductase ([EC1.18.1.2], FNR) from Bacillus subtilis (BsFNR) is a homodimeric flavoprotein sharing structural homology with bacterial NADPH-thioredoxin reductase. Pre-steady-state kinetics of the reactions of BsFNR with NADP(+), NADPH, NADPD (deuterated form) and B. subtilis ferredoxin (BsFd) using stopped-flow spectrophotometry were studied. Mixing BsFNR with NADP(+) and NADPH yielded two types of charge-transfer (CT) complexes, oxidized FNR (FNR(ox))-NADPH and reduced FNR (FNR(red))-NADP(+), both having CT absorption bands centered at approximately 600n m. After mixing BsFNR(ox) with about a 10-fold molar excess of NADPH (forward reaction), BsFNR was almost completely reduced at equilibrium. When BsFNR(red) was mixed with NADP(+), the amount of BsFNR(ox) increased with increasing NADP(+) concentration, but BsFNR(red) remained as the major species at equilibrium even with about 50-fold molar excess NADP(+). In both directions, the hydride-transfer was the rate-determining step, where the forward direction rate constant (~500 s(-1)) was much higher than the reverse one (reaction. The characteristics of the BsFNR reactions with NADP(+)/NADPH were compared with those of other types of FNRs. Copyright © 2016 Elsevier B.V. All rights reserved.

Experimental studies of the kinetics of small polyatomic free radicals in combustion reactions; Moniatomisten radikaalien kinetiikka palamisreaktioissa, kokeellinen tutkimus

Energy Technology Data Exchange (ETDEWEB)

Seetula, J. [Helsinki Univ. (Finland). Lab. of Physical Chemistry

1996-12-01

The kinetics of the reactions of CH{sub 2}Cl, CHClBr, CH{sub 3}CCl{sub 2} and CCl{sub 3}, with Cl{sub 2} has been investigated in a tubular reactor coupled to a photoionization mass spectrometer. The radicals of interest, R, were generated homogeneously in the reactor by pulse 248 nm exciplex laser photolysis. The decay of R was monitored as a function of Cl{sub 2} concentration under pseudo-first-order condition to determine the rate constant as a function of temperature pressure. The reactions were studied separately over a temperature range up to a temperature of 873 K. The rate constants of CH{sub 2}Cl, CHClBr and CH{sub 3}CCl{sub 2} radicals determined were fitted to three-parameter Arrhenius-type expression (with units of cm{sup 3} molecule{sup -1} s{sup -1}): k(CH{sub 2}Cl) = 1.05x10{sup -16} x (T){sup 1.4} x exp(-357 J mol{sup -1} / RT), k(CHClBr) = 5.83x10{sup -20} x (T){sup 2.3} x exp(-300 J mol{sup -1}/ RT) and k(CH{sub 3}CCl{sub 2}) 1.10x10{sup -}2{sup 6} x (T){sup 4.3} x exp(15000 J mol{sup -1}/ RT). The rate constants CCl{sub 3} radical were fitted to a two-parameter Arrhenius expression (units in cm{sup 3} molecule{sup -1} s{sup -1}): k(CCl{sub 3}) = (8.1 +- 6.7)10{sup -l3} exp[-(25.0 +- 8.7) kJ mol{sup -1}/ RT]. An Arrhenius expression for the reaction of Cl+CCl{sub 4} -> <- CCl{sub 3}+Cl{sub 2} is also obtained from the kinetics of the reaction of CCl{sub 3} radical with Cl{sub 2} combined with the known heat of formation and entropy values of CCl{sub 3} free radical to be as follows (in units cm{sup 3} molecule{sup -1-}5 s{sup -1}): k(Cl+CCl{sub 4}) = (3.9 + 3.2)10{sup -10} exp[-(71 + 9) kJ mol{sup -1}/ RT]. The error limits stated are l{sigma}+Student`s t and base on statistical uncertainties only. (author)

Reaction studies of hot silicon, germanium and carbon atoms

International Nuclear Information System (INIS)

Gaspar, P.P.

1990-01-01

The goal of this project was to increase the authors understanding of the interplay between the kinetic and electronic energy of free atoms and their chemical reactivity by answering the following questions: (1) what is the chemistry of high-energy carbon silicon and germanium atoms recoiling from nuclear transformations; (2) how do the reactions of recoiling carbon, silicon and germanium atoms take place - what are the operative reaction mechanisms; (3) how does the reactivity of free carbon, silicon and germanium atoms vary with energy and electronic state, and what are the differences in the chemistry of these three isoelectronic atoms? This research program consisted of a coordinated set of experiments capable of achieving these goals by defining the structures, the kinetic and internal energy, and the charge states of the intermediates formed in the gas-phase reactions of recoiling silicon and germanium atoms with silane, germane, and unsaturated organic molecules, and of recoiling carbon atoms with aromatic molecules. The reactions of high energy silicon, germanium, and carbon atoms created by nuclear recoil were studied with substrates chosen so that their products illuminated the mechanism of the recoil reactions. Information about the energy and electronic state of the recoiling atoms at reaction was obtained from the variation in end product yields and the extent of decomposition and rearrangement of primary products (usually reactive intermediates) as a function of total pressure and the concentration of inert moderator molecules that remove kinetic energy from the recoiling atoms and can induce transitions between electronic spin states. 29 refs

Golden rule kinetics of transfer reactions in condensed phase: the microscopic model of electron transfer reactions in disordered solid matrices.

Science.gov (United States)

Basilevsky, M V; Odinokov, A V; Titov, S V; Mitina, E A

2013-12-21

The algorithm for a theoretical calculation of transfer reaction rates for light quantum particles (i.e., the electron and H-atom transfers) in non-polar solid matrices is formulated and justified. The mechanism postulated involves a local mode (an either intra- or inter-molecular one) serving as a mediator which accomplishes the energy exchange between the reacting high-frequency quantum mode and the phonon modes belonging to the environment. This approach uses as a background the Fermi golden rule beyond the usually applied spin-boson approximation. The dynamical treatment rests on the one-dimensional version of the standard quantum relaxation equation for the reduced density matrix, which describes the frequency fluctuation spectrum for the local mode under consideration. The temperature dependence of a reaction rate is controlled by the dimensionless parameter ξ0 = ℏω0/k(B)T where ω0 is the frequency of the local mode and T is the temperature. The realization of the computational scheme is different for the high/intermediate (ξ0 regime, the Redfield approximation to the solution of the relaxation equation proved to be sufficient and efficient in practical applications. The study of the essentially quantum-mechanical low-temperature kinetic regime in its asymptotic limit requires the implementation of the exact relaxation equation. The coherent mechanism providing a non-vanishing reaction rate has been revealed when T → 0. An accurate computational methodology for the cross-over kinetic regime needs a further elaboration. The original model of the hopping mechanism for electronic conduction in photosensitive organic materials is considered, based on the above techniques. The electron transfer (ET) in active centers of such systems proceeds via local intra- and intermolecular modes. The active modes, as a rule, operate beyond the kinetic regimes, which are usually postulated in the existing theories of the ET. Our alternative dynamic ET model for local

The kinetics of free radical metathetical and addition reactions in silane solutions

International Nuclear Information System (INIS)

Aloni, R.

1976-12-01

In this work radiolytic technique was employed for the initiation of free radical chainreactions in silane solution. The kinetic analysis of the chain mechanism in various solutions enabled the determination of the Arrhenius parameters for metathesis, addition and unimolecular decomposition reactions which make up the chainpropagation sequence in the systems studied. The following radical reactions were investigated: chlorine atom abstraction from chloromethanes by SiCl 3 and Et 3 Si radicals, and chlorine atom abstraction from chloroethanes by Et 3 Si radicals; unimolecular decomposition reactions and hydrogen atom abstraction, *from the solvent, of chloroethyl radicals in triethylsilane solutions; addition and abstraction reactions of Et 3 Si radicals with chloroolefins. Arrhenius parameters were determined for abstraction of chlorine atom from CH 3 Cl, CH 2 Cl 2 , CHCl 3 and CCl 4 , by SiCl 3 radicals and from CCl 4 , CHCl 3 , CH 2 Cl 2 , CCl 3 CN, C 2 Cl 5 H, sym-C 2 Cl 4 H 2 , asym-C 2 Cl 4 H 2 , 1.1.1-C 2 Cl 3 H 3 , 1.1.1-C 2 Dl 3 F 3 and 1.1-C 2 Cl 2 H 4 by Et 3 Si radicals. (author)

Oxidation of β-lactam antibiotics by peracetic acid: Reaction kinetics, product and pathway evaluation.

Science.gov (United States)

Zhang, Kejia; Zhou, Xinyan; Du, Penghui; Zhang, Tuqiao; Cai, Meiquan; Sun, Peizhe; Huang, Ching-Hua

2017-10-15

Peracetic acid (PAA) is a disinfection oxidant used in many industries including wastewater treatment. β-Lactams, a group of widely prescribed antibiotics, are frequently detected in wastewater effluents and surface waters. The reaction kinetics and transformation of seven β-lactams (cefalexin (CFX), cefadroxil (CFR), cefapirin (CFP), cephalothin (CFT), ampicillin (AMP), amoxicillin (AMX) and penicillin G (PG)) toward PAA were investigated to elucidate the behavior of β-lactams during PAA oxidation processes. The reaction follows second-order kinetics and is much faster at pH 5 and 7 than at pH 9 due to speciation of PAA. Reactivity to PAA follows the order of CFR ∼ CFX > AMP ∼ AMX > CFT ∼ CFP ∼ PG and is related to β-lactam's nucleophilicity. The thioether sulfur of β-lactams is attacked by PAA to generate sulfoxide products. Presence of the phenylglycinyl amino group on β-lactams can significantly influence electron distribution and the highest occupied molecular orbital (HOMO) location and energy in ways that enhance the reactivity to PAA. Reaction rate constants obtained in clean water matrix can be used to accurately model the decay of β-lactams by PAA in surface water matrix and only slightly overestimate the decay in wastewater matrix. Results of this study indicate that the oxidative transformation of β-lactams by PAA can be expected under appropriate wastewater treatment conditions. Copyright © 2017. Published by Elsevier Ltd.

Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study

Directory of Open Access Journals (Sweden)

Amrit P. Toor

2011-05-01

Full Text Available The kinetic behavior of esterification of lactic acid with isopropanol over an acidic cation exchange resin, Amberlyst 15, was studied under isothermal condition. Isopropyl lactate synthesized in this reaction is an important pharmaceutical intermediate. The experiments were carried out in a stirred batch reactor in the temperature range of 323.15 to 353.15 K. The effect of various parameters such as temperature, molar ratio and catalyst loading was studied. Variation in parameters on rate of reaction demonstrated that the reaction was intrinsically controlled. Kinetic modeling was performed using Eley-Rideal model which acceptably fits the experimental data. The activation energy was found to be 22.007 kJ/mol and frequency factor was 0.036809 l2 g-1 mol-1 min-1 for forward reaction. The value of entropy for the forward reaction was found to be 182.317 J K-1 mol-1 . © 2011 BCREC UNDIP. All rights reserved(Received: 19th January 2011, Revised: 16th March 2011; Accepted: 16th March 2011[How to Cite: A.P. Toor, M. Sharma, S. Thakur, and R. K. Wanchoo. (2011. Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study. Bulletin of Chemical Reaction Engineering and Catalysis, 6(1: 39-45. doi:10.9767/bcrec.6.1.791.39-45][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.791.39-45 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/791 ] | View in  

Reactions of lactose during heat treatment of milk : a quantitative study

NARCIS (Netherlands)

Berg, H.E.

1993-01-01

The kinetics of the chemical reactions of lactose during heat treatment of milk were studied. Skim milk and model solutions resembling milk were heated. Reaction products were determined and the influence of varying lactose, casein and fat concentration on the formation of these products

Kinetic study of formation of sodalite from a kaolin waste of Jari river - PA, Brazil

International Nuclear Information System (INIS)

Silva, L.N. da; Paz, S.P.A. da; Angelica, R.S.; Neves, R.F.

2011-01-01

Zeolites are materials with a wide industrial application, which has motivated the development of a large number of scientific papers on this topic. This work presents a kinetic study of the formation process of sodalite produced from the reaction of the kaolin waste in the presence of sodium hydroxide solution (5M) performed at temperatures of 80, 100, 120 and 150 ° C. The process was conducted in batch, static, and autoclaves lined with Teflon, and monitoring the kinetics was performed by ex situ XRD analysis of the materials obtained in the time interval from 2 to 24 hours. The kinetic model that best describes this transformation is zero-order homogeneous reaction. Finally, we conclude that the technique of X-ray diffraction is a powerful tool to study the kinetics of phase transformation ex situ. (author)

Kinetics and mechanism of the furan peroxide formation in the reaction of furfural with hydrogen peroxide in the presence and absence of sodium molybdate

International Nuclear Information System (INIS)

Grunskaya, E.P.; Badovskaya, L.A.; Kaklyugina, T.Ya.; Poskonin, V.V.

2000-01-01

Kinetics of the initial stage of the reaction of furfural with hydrogen peroxide are studied in the presence of Na 2 MoO 4 in water and without catalytic additions in n-butanol. Organic peroxide having in its disposal Mo(6), which is the only product on the initial stage of the reaction, is formed since the first minutes of oxidation of furfural by hydrogen peroxide with the presence of Na 2 MoO 4 . The mechanisms of conversion of furfural in the Na 2 MoO 4 - H 2 O system and its oxidation by peroxide without sodium molybdate are discussed. Schemes of formation of furfural complexes based on the results of kinetic studies are suggested. Comparison of obtained data demonstrates that presence of the sodium molybdates in the reaction medium trends to change of reaction procedure in the hydrogen peroxide [ru

Kinetics of H-D exchange in olefins with complicating reactions

International Nuclear Information System (INIS)

Trokhimets, A.I.

1979-01-01

The kinetics of H-D-exchange is considered for olefins under conditions when simple and complicated exchange occur together with hydrogenation. If hydrogenation takes place in the system, it is theoretically impossible to derive the integrated rate equation for the accumulation of deuterium in the olefin. The variation of the concentration of different deuteroolefins during the process can be calculated numerically. A method is proposed for evaluating the contribution of individual steps to the overall process and determining the rate constants of the most important reactions. (author)

Optically Controlled Electron-Transfer Reaction Kinetics and Solvation Dynamics : Effect of Franck-Condon States

NARCIS (Netherlands)

Gupta, Kriti; Patra, Aniket; Dhole, Kajal; Samanta, Alok Kumar; Ghosh, Swapan K.

2017-01-01

Experimental results for optically controlled electron-transfer reaction kinetics (ETRK) and nonequilibrium solvation dynamics (NESD) of Coumarin 480 in DMPC vesicle show their dependence on excitation wavelength λex. However, the celebrated Marcus theory and linear-response-theory-based approaches

A low temperature investigation of the gas-phase N(2D) + NO reaction. Towards a viable source of N(2D) atoms for kinetic studies in astrochemistry.

Science.gov (United States)

Nuñez-Reyes, Dianailys; Hickson, Kevin M

2018-06-18

The gas-phase reaction of metastable atomic nitrogen N(2D) with nitric oxide has been investigated over the 296-50 K temperature range using a supersonic flow reactor. As N(2D) could not be produced photolytically in the present work, these excited state atoms were generated instead through the C(3P) + NO → N(2D) + CO reaction while C(3P) atoms were created in situ by the 266 nm pulsed laser photolysis of CBr4 precursor molecules. The kinetics of N(2D) atoms were followed on-resonance by vacuum ultraviolet laser induced fluorescence at 116.7 nm. The measured rate constants for the N(2D) + NO reaction are in excellent agreement with most of the earlier work at room temperature and represent the only available kinetic data for this process below 296 K. The rate constants are seen to increase slightly as the temperature falls to 100 K with a more substantial increase at even lower temperature; a finding which is not reproduced by theoretical work. The prospects for using this chemical source of N(2D) atoms in future studies of a wide range of N(2D) atom reactions are discussed.

Effect of ionic strength on the kinetics of ionic and micellar reactions in aqueous solution

International Nuclear Information System (INIS)

Dung, M.H.; Kozak, J.J.

1982-01-01

The effect of electrostatic forces on the rate of reaction between ions in aqueous solutions of intermediate ionic strength is studied in this paper. We consider the kinetics of reactions involving simple ionic species (1--1 and 2--2 electrolyte systems) as well as kinetic processes mediated by the presence of micellar ions (or other charged organizates). In the regime of ionic strength considered, dielectric saturation of the solvent in the vicinity of the reacting ions must be taken into account and this is done by introducing several models to describe the recovery of the solvent from saturation to its continuum dielectric behavior. To explore the effects of ion size, charge number, and ionic strength on the overall rate constant for the process considered, we couple the traditional theory of ionic reactions in aqueous solution with calculations of the electrostatic potential obtained via solution of the nonlinear Poisson--Boltzmann equation. The great flexibility of the nonlinear Poisson--Boltzmann theory allows us to explore quantitatively the influence of each of these effects, and our simulations show that the short-range properties of the electrostatic potential affect primarily kinetically controlled processes (to varying degrees, depending on the ionic system considered) whereas the down-range properties of the potential play a (somewhat) greater role in influencing diffusion-controlled processes. A detailed examination is made of ionic strength effects over a broad range of ionic concentrations. In the regime of low ionic strength, the limiting slope and intercept of the curve describing the dependence of log k/sub D/ on I/sup 1/2//(1+I/sup 1/2/) may differ considerably from the usual Debye--Hueckel limiting relations, depending on the particular model chosen to describe local saturation effects

DNA effects upon the reaction between acetonitrile pentacyanoferrate (II) and ruthenium pentammine pyrazine: Kinetic and thermodynamic evidence of the interaction of DNA with anionic species

International Nuclear Information System (INIS)

Grueso, E.; Prado-Gotor, R.; Lopez, M.; Gomez-Herrera, C.; Sanchez, F.

2005-01-01

The kinetics of the reaction between ruthenium pentaammine pyrazine and acetonitrile pentacyanoferrate (II) to obtain the binuclear anionic complex [Fe(CN) 5 pzRu(NH 3 ) 5 ] - , and the reverse (dissociation) process, have been studied in solutions containing DNA. The results corresponding to this reaction and those corresponding to the reverse (dissociation) process show a clear influence of DNA on their kinetics. The results can be interpreted using a modified Pseudophase Model. From the results obtained for the dissociation reaction one can conclude that the binuclear anionic complex [Fe(CN) 5 pzRu(NH 3 ) 5 ] - interacts with DNA

Importance of (n,xn) reactions in evaluating kinetic parameters of subcritical assemblies: from classic to modern formalism

Energy Technology Data Exchange (ETDEWEB)

Talamo, Alberto; Gohar, Yousry, E-mail: alby@anl.gov [Argonne National Laboratory, Lemont, IL (United States); Dulla, Sandra; Ravetto, Piero [Politecnico di Torino (Italy)

2011-07-01

The importance of (n,xn) reactions must be taken into consideration while calculating the kinetic parameters of subcritical assemblies driven by an external neutron source. This study is divided into two parts, the first part is dedicated to the classic definition of the neutron source multiplication factor and two alternative calculation methodologies are compared. The second part considers a new definition of the kinetic parameters for subcritical assemblies, with particular emphasis on the delayed neutron fraction and generation time. This new definition has been modified to take into account the external neutron source and (n,xn) reactions, which increase the fraction of prompt neutrons. The developed theoretical framework has been applied by Monte Carlo and deterministic calculations to the YALINA Thermal subcritical assembly in Belarus. This facility can be driven by californium, deuterium-deuterium (D-D), or deuterium-tritium (D-T) external neutron sources. For the D-T neutron source, (n,xn) reactions must be taken into account in order to produce accurate results because the average energy of D-T source neutrons is 14.1 MeV, a value much higher than the threshold energy of the (n,2n) cross section of uranium isotopes. (author)

Importance of (n,xn) reactions in evaluating kinetic parameters of subcritical assemblies: from classic to modern formalism

International Nuclear Information System (INIS)

Talamo, Alberto; Gohar, Yousry; Dulla, Sandra; Ravetto, Piero

2011-01-01

The importance of (n,xn) reactions must be taken into consideration while calculating the kinetic parameters of subcritical assemblies driven by an external neutron source. This study is divided into two parts, the first part is dedicated to the classic definition of the neutron source multiplication factor and two alternative calculation methodologies are compared. The second part considers a new definition of the kinetic parameters for subcritical assemblies, with particular emphasis on the delayed neutron fraction and generation time. This new definition has been modified to take into account the external neutron source and (n,xn) reactions, which increase the fraction of prompt neutrons. The developed theoretical framework has been applied by Monte Carlo and deterministic calculations to the YALINA Thermal subcritical assembly in Belarus. This facility can be driven by californium, deuterium-deuterium (D-D), or deuterium-tritium (D-T) external neutron sources. For the D-T neutron source, (n,xn) reactions must be taken into account in order to produce accurate results because the average energy of D-T source neutrons is 14.1 MeV, a value much higher than the threshold energy of the (n,2n) cross section of uranium isotopes. (author)

UV-visible spectrum of the phenyl radical and kinetics of its reaction with NO in the gas phase

DEFF Research Database (Denmark)

Wallington, T.J.; Egsgaard, H.; Nielsen, O.J.

1998-01-01

Pulse radiolysis transient UV-visible absorption spectroscopy was used to study the UV-visible absorption spectrum (225-575 nm) of the phenyl radical, C6H5(.), and kinetics of its reaction with NO. Phenyl radicals have a strong broad featureless absorption in the region of 225-340 nm...

Toward a Kinetic Model for Acrylamide Formation in a Glucose-Asparagine Reaction System

NARCIS (Netherlands)

Knol, J.J.; Loon, W.A.M.; Linssen, J.P.H.; Ruck, A.L.; Boekel, van M.A.J.S.

2005-01-01

A kinetic model for the formation of acrylamide in a glucose-asparagine reaction system is pro-posed. Equimolar solutions (0.2 M) of glucose and asparagine were heated at different tempera-tures (120-200 C) at pH 6.8. Besides the reactants, acrylamide, fructose, and melanoidins were quantified after

Study the influence of reacted aliphatic amine series length on its kinetic reaction with dimeric fatty acid C36 and properties of resulted polyamide

International Nuclear Information System (INIS)

Al-Mohammad, H.; Falah, A.; Al-Hammoy, M.

2013-01-01

Kinetic studies were carried out on the reaction between dimeric fatty acid C 3 6 with 1.3 Diamino propane and 1.4 Diamino butane and 1.6 Diamino hexane and 1.8 Diamino octane in molten phase. The reaction was performed at 145 o C. The polyamidation reaction was found to be on the overall a second order up to 83% conversion for reaction dimeric fatty acid C-36 with 1.3 Diamino propane and 86% conversion for reaction dimeric fatty acid C 3 6 with 1.4 Diamino butane and 87% conversion for reaction dimeric fatty acid C 3 6 with 1.6 Diamino hexane and 1.8 Diamino octane then the reaction order changes to the third order above last conversion. The degree of polymerization,number average molecular weight and weight average molecular weight have been calculated during different times. Their relationships with the times are linear until last conversion. The melting point and thermodynamic constants for melting are determined by use of differential scanning calorimetry DSC. The melting point and thermodynamic constants increase by increasing the length of reacted amine series. (author)

Kinetics of the high temperature oxygen exchange reaction on 238PuO2 powder

International Nuclear Information System (INIS)

Whiting, Christofer E.; Du, Miting; Felker, L. Kevin; Wham, Robert M.; Barklay, Chadwick D.; Kramer, Daniel P.

2015-01-01

Oxygen exchange reactions performed on PuO 2 suggest the reaction is influenced by at least three mechanisms: an internal chemical reaction, surface mobility of active species/defects, and surface exchange of gaseous oxygen with lattice oxygen. Activation energies for the surface mobility and internal chemical reaction are presented. Determining which mechanism is dominant appears to be a complex function including at least specific surface area and temperature. Thermal exposure may also impact the oxygen exchange reaction by causing reductions in the specific surface area of PuO 2 . Previous CeO 2 surrogate studies exhibit similar behavior, confirming that CeO 2 is a good qualitative surrogate for PuO 2 , in regards to the oxygen exchange reaction. Comparison of results presented here with previous work on the PuO 2 oxygen exchange reaction allows complexities in the previous work to be explained. These explanations allowed new conclusions to be drawn, many of which confirm the conclusions presented here. - Highlights: • PuO 2 Oxygen exchange kinetics can be influenced by at least 3 different mechanisms. • An internal chemical reaction controls the rate at high temperature and large SSA. • Surface mobility and surface exchange influence rate at lower temperatures and SSA. • Exchange temperatures may alter SSA and make data difficult to interpret.

Kinetic modeling studies of SOA formation from α-pinene ozonolysis

Science.gov (United States)

Gatzsche, Kathrin; Iinuma, Yoshiteru; Tilgner, Andreas; Mutzel, Anke; Berndt, Torsten; Wolke, Ralf

2017-11-01

This paper describes the implementation of a kinetic gas-particle partitioning approach used for the simulation of secondary organic aerosol (SOA) formation within the SPectral Aerosol Cloud Chemistry Interaction Model (SPACCIM). The kinetic partitioning considers the diffusion of organic compounds into aerosol particles and the subsequent chemical reactions in the particle phase. The basic kinetic partitioning approach is modified by the implementation of chemical backward reaction of the solute within the particle phase as well as a composition-dependent particle-phase bulk diffusion coefficient. The adapted gas-phase chemistry mechanism for α-pinene oxidation has been updated due to the recent findings related to the formation of highly oxidized multifunctional organic compounds (HOMs). Experimental results from a LEAK (Leipziger Aerosolkammer) chamber study for α-pinene ozonolysis were compared with the model results describing this reaction system.The performed model studies reveal that the particle-phase bulk diffusion coefficient and the particle-phase reactivity are key parameters for SOA formation. Using the same particle-phase reactivity for both cases, we find that liquid particles with higher particle-phase bulk diffusion coefficients have 310 times more organic material formed in the particle phase compared to higher viscous semi-solid particles with lower particle-phase bulk diffusion coefficients. The model results demonstrate that, even with a moderate particle-phase reactivity, about 61 % of the modeled organic mass consists of reaction products that are formed in the liquid particles. This finding emphasizes the potential role of SOA processing. Moreover, the initial organic aerosol mass concentration and the particle radius are of minor importance for the process of SOA formation in liquid particles. A sensitivity study shows that a 22-fold increase in particle size merely leads to a SOA increase of less than 10 %.Due to two additional

The chemical kinetics of the reactions of lithium with steam-air mixtures

International Nuclear Information System (INIS)

Barnett, D.S.; Kazimi, M.S.

1989-04-01

This work involved the experimental and analytical determination of the consequences of lithium fires in the presence of steam. Experiments were performed to characterize the chemical reactions of lithium with steam-nitrogen and steam-air mixtures. Models were introduced in the LITFIRE code to describe lithium fires in the presence of steam inside the containment building and plasma chamber of a hypothetical fusion reactor. The code was also equipped with the capability to determine the effects of decay heat and lithium fire on the temperature response of the reactor first wall in the event of a coolant disturbance. Forty-two kinetics experiments were performed in which a stream of steam-nitrogen or steam-air was passed over and reacted with approximately three grams of lithium heated to a predetermined temperature. The lithium reaction rates with the constituent gases were measured and characterized for a wide range of lithium temperatures and gas compositions. Experiments were performed with steam molar concentrations of 5, 15 and 30% and lithium temperatures ranging from 400 to 1100 degree C, inclusive. The LITFIRE code was modified to enable it to model the interactions of lithium with steam-air atmospheres. Results of the reaction kinetics experiments were used in the reaction model, and the heat transfer model was expanded to allow it to handle condensible atmospheres. Three groups of accidents were investigated: a spill on the containment building floor, a spill inside the reactor plasma chamber, and a spill inside the plasma chamber with steam injection to the containment building simulating a steam line break. The results were compared to dry air cases under the same conditions. 23 refs., 66 figs., 18 tabs

Kinetics of the radiation-induced exchange reactions of H2, D2, and T2: a review

International Nuclear Information System (INIS)

Pyper, J.W.; Briggs, C.K.

1978-01-01

Mixtures of H 2 --T 2 or D 2 --T 2 will exchange to produce HT or DT due to catalysis by the tritium β particle. The kinetics of the reaction D 2 + T 2 = 2DT may play an important role in designing liquid or solid targets of D 2 --DT--T 2 for implosion fusion, and distillation schemes for tritium cleanup systems in fusion reactors. Accordingly, we have critically reviewed the literature for information on the kinetics and mechanism of radiation-induced self-exchange reactions among the hydrogens. We found data for the reaction H 2 + T 2 = 2HT in the gas phase and developed a scheme based on these data to predict the halftime to equilibrium for any gaseous H 2 + T 2 mixture at ambient temperature with an accuracy of +-10 percent. The overall order of the H 2 + T 2 = 2HT reaction is 1.6 based on an initial rate treatment of the data. The most probable mechanism for radiation-induced self-exchange reaction is an ion-molecule chain mechanism

Kinetics on the reaction of 6-chloroquinoline and p-substituted benzoylchlorides under high pressures

International Nuclear Information System (INIS)

Kim, Eung Ryul; Lim, Jong Wan; Kim, Se Kyong; Ko, Young Shin

2002-01-01

The reactions rates of substituted 6-chloroquinoline, with p-substituted benzoyichlorides (p-CH 3 , p-H, p-NO 2 ) have been measured by conductometry in acetonitrile, and the rate constants are determined at various temperatures (10,15,20,25 .deg. C) and pressures (1, 200, 500, 1000 bar). From the values of rate constants, the activation parameters (Ea, ΔV ≠ , ΔH ≠ , ΔS ≠ , and ΔG ≠ ) and the pressure dependence of Hammett ρ values were determined. The rate constants increased with increasing temperatures and pressures, and are further increased to introduction to the electron donor substituents in substrate (p-NO 2 ) with 6-chloroquinoline. When, the activation volume and the activation entropy are all negative. And the Hammett ρ values are positive for the substrate over the pressure and temperature range studied. The results of kinetic studies for pressure and substituent show that thease reactions proceed in typical S N 2 reaction mechanism and 'associative S N 2' in bond formation favored with increasing pressures

Chemical kinetic studies of atmospheric reactions using tunable diode laser spectroscopy

Science.gov (United States)

Worsnop, Douglas R.; Nelson, David D.; Zahniser, Mark S.

1993-01-01

IR absorption using tunable diode laser spectroscopy provides a sensitive and quantitative detection method for laboratory kinetic studies of atmospheric trace gases. Improvements in multipass cell design, real time signal processing, and computer controlled data acquisition and analysis have extended the applicability of the technique. We have developed several optical systems using off-axis resonator mirror designs which maximize path length while minimizing both the sample volume and the interference fringes inherent in conventional 'White' cells. Computerized signal processing using rapid scan (300 kHz), sweep integration with 100 percent duty cycle allows substantial noise reduction while retaining the advantages of using direct absorption for absolute absorbance measurements and simultaneous detection of multiple species. Peak heights and areas are determined by curve fitting using nonlinear least square methods. We have applied these techniques to measurements of: (1) heterogeneous uptake chemistry of atmospheric trace gases (HCl, H2O2, and N2O5) on aqueous and sulfuric acid droplets; (2) vapor pressure measurements of nitric acid and water over prototypical stratospheric aerosol (nitric acid trihydrate) surfaces; and (3) discharge flow tube kinetic studies of the HO2 radical using isotopic labeling for product channel and mechanistic analysis. Results from each of these areas demonstrate the versatility of TDL absorption spectroscopy for atmospheric chemistry applications.

Kinetics of heterogeneous chemical reactions: a theoretical model for the accumulation of pesticides in soil.

Science.gov (United States)

Lin, S H; Sahai, R; Eyring, H

1971-04-01

A theoretical model for the accumulation of pesticides in soil has been proposed and discussed from the viewpoint of heterogeneous reaction kinetics with a basic aim to understand the complex nature of soil processes relating to the environmental pollution. In the bulk of soil, the pesticide disappears by diffusion and a chemical reaction; the rate processes considered on the surface of soil are diffusion, chemical reaction, vaporization, and regular pesticide application. The differential equations involved have been solved analytically by the Laplace-transform method.

Kinetic Modeling of the Reaction Rate for Quartz and Carbon Black Pellet

Science.gov (United States)

Li, Fei; Tangstad, Merete

2018-06-01

The kinetic modeling for the carbothermal reduction reaction rate in quartz and carbon black pellets is studied at different temperatures, under varying CO partial pressures in ambient atmosphere, varying carbon contents, different quartz particle sizes, and different crucible opening areas. Carbon black is produced by the cracking of natural gas. The activation energy of the SiC-producing step was determined to be 594 kJ/mol. The averaged pre-exponential factor A obtained from 1898 K, 1923 K, and 1948 K (1625 °C, 1650 °C, and 1675 °C) is 2.62E+16 min-1. The reaction rate of the gas-solid interface factor, fix-C content ( X fix-C), temperature ( T), and CO partial pressure ( X CO) can be expressed as follows: {{d/pct}}{{{d}t}} = (1 - 0.40 × X_{{{fix} - C}}^{ - 0.86} × {pct}) × 2.62 × 10^{16} × \\exp ( { - 594000/RT} ) × (2.6 - 0.015 × X_{co} ).

Tunneling and reflection in unimolecular reaction kinetic energy release distributions

Science.gov (United States)

Hansen, K.

2018-02-01

The kinetic energy release distributions in unimolecular reactions is calculated with detailed balance theory, taking into account the tunneling and the reflection coefficient in three different types of transition states; (i) a saddle point corresponding to a standard RRKM-type theory, (ii) an attachment Langevin cross section, and (iii) an absorbing sphere potential at short range, without long range interactions. Corrections are significant in the one dimensional saddle point states. Very light and lightly bound absorbing systems will show measurable effects in decays from the absorbing sphere, whereas the Langevin cross section is essentially unchanged.

Kinetics of the glucose/glycine Maillard reaction pathways: influences of pH and reactant initial concentrations

NARCIS (Netherlands)

Martins, S.I.F.S.; Boekel, van M.A.J.S.

2005-01-01

A previously proposed kinetic model for the glucose/glycine Maillard reaction pathways has been validated by changing the initial pH (4.8, 5.5, 6.0, 6.8 and 7.5) of the reaction and reactant initial concentrations (1:2 and 2:1 molar ratios were compared to the 1:1 ratio). The model consists of 10

A Mathematical Model for the Multiphase Transport and Reaction Kinetics in a Ladle with Bottom Powder Injection

Science.gov (United States)

Lou, Wentao; Zhu, Miaoyong

2017-12-01

A computation fluid dynamics-population balance model-simultaneous reaction model (CFD-PBM-SRM) coupled model has been proposed to study the multiphase flow behavior and refining reaction kinetics in a ladle with bottom powder injection, and some new and important phenomena and mechanisms are presented. For the multiphase flow behavior, the effects of bubbly plume flow, powder particle motion, particle-particle collision and growth, particle-bubble collision and adhesion, and powder particle removal into top slag are considered. For the reaction kinetics, the mechanisms of multicomponent simultaneous reactions, including Al, S, Si, Mn, Fe, and O, at the multi-interface, including top slag-liquid steel interface, air-liquid steel interface, powder droplet-liquid steel interface, and bubble-liquid steel interface, are presented, and the effect of sulfur solubility in the powder droplet on the desulfurization is also taken into account. Model validation is carried out using hot tests in a 2-t induction furnace with bottom powder injection. The result shows that the powder particles gradually disperse in the entire furnace; in the vicinity of the bottom slot plugs, the desulfurization product CaS is liquid phase, while in the upper region of the furnace, the desulfurization product CaS is solid phase. The predicted sulfur contents by the present model agree well with the measured data in the 2-t furnace with bottom powder injection.

The mechanism distinguishability problem in biochemical kinetics: the single-enzyme, single-substrate reaction as a case study.

Science.gov (United States)

Schnell, Santiago; Chappell, Michael J; Evans, Neil D; Roussel, Marc R

2006-01-01

A theoretical analysis of the distinguishability problem of two rival models of the single enzyme-single substrate reaction, the Michaelis-Menten and Henri mechanisms, is presented. We also outline a general approach for analysing the structural indistinguishability between two mechanisms. The approach involves constructing, if possible, a smooth mapping between the two candidate models. Evans et al. [N.D. Evans, M.J. Chappell, M.J. Chapman, K.R. Godfrey, Structural indistinguishability between uncontrolled (autonomous) nonlinear analytic systems, Automatica 40 (2004) 1947-1953] have shown that if, in addition, either of the mechanisms satisfies a particular criterion then such a transformation always exists when the models are indistinguishable from their experimentally observable outputs. The approach is applied to the single enzyme-single substrate reaction mechanism. In principle, mechanisms can be distinguished using this analysis, but we show that our ability to distinguish mechanistic models depends both on the precise measurements made, and on our knowledge of the system prior to performing the kinetics experiments.

Kinetic and reaction pathways of methanol oxidation on platinum

International Nuclear Information System (INIS)

McCabe, R.W.; McCready, D.F.

1986-01-01

Methanol oxidation kinetics were measured on Pt wires in a flow reactor at pressures between 30 and 130 Pa. The kinetics were measured as a function of oxygen-to-methanol equivalence ratio phi and wire temperature. In methanol-lean feeds (phi 2 CO, CO 2 , and H 2 O were the only products; in methanol-rich feeds (phi > 1), CO, H 2 , H 2 CO, CO 2 , and H 2 O were observed. Experiments with 18 O 2 showed that the principal methanol oxidation pathway does not involve C-O bond dissociation. However, the 18 O 2 experiments, together with other features of the methanol oxidation data, also provided evidence for a minor oxidation pathway (accounting for less than 1% of the product CO 2 ) which proceeds through a carbon intermediate. A mathematical model is presented which describes the principal CH 3 OH oxidation pathway as a series reaction involving adsorbed H 2 CO and CO intermediates. Consistent with experimental results, the model predicts that inhibition by adsorbed CO should be weaker for CH 3 OH and H 2 CO oxidation than for CO oxidation. 34 references, 10 figures, 2 tables

Kinetic study and thermal decomposition behavior of viscoelastic memory foam

International Nuclear Information System (INIS)

Garrido, María A.; Font, Rafael; Conesa, Juan A.

2016-01-01

Highlights: • The thermal degradation has been studied under three different atmospheres. • Pyrolysis and combustion kinetic models have been proposed. • Evolved products under different atmospheres have been analyzed by TG-FTIR and TG-MS. - Abstract: A systematic investigation of the thermal decomposition of viscoelastic memory foam (VMF) was performed using thermogravimetric analysis (TGA) to obtain the kinetic parameters, and thermogravimetric analysis coupled to Fourier Transformed Infrared Spectrometry (TGA-FTIR) and thermogravimetric analysis coupled to Mass Spectrometry (TGA-MS) to obtain detailed information of evolved products on pyrolysis and oxidative degradations. Two consecutive nth-order reactions were employed to correlate the experimental data from dynamic and isothermal runs performed at three different heating rates (5, 10 and 20 K/min) under an inert atmosphere. On the other hand, for the kinetic study of the oxidative decomposition, the data from combustion (synthetic air) and poor oxygen combustion (N_2:O_2 = 9:1) runs, at three heating rates and under dynamic and isothermal conditions, were correlated simultaneously. A kinetic model consisting of three consecutive reactions presented a really good correlation in all runs. TGA-FTIR analysis showed that the main gases released during the pyrolysis of VMF were determined as ether and aliphatic hydrocarbons, whereas in combustion apart from the previous gases, aldehydes, amines and CO_2 have also been detected as the main gases. These results were confirmed by the TGA-MS.

Oxidation of Methionine by Tripropylammonium Fluorochromate-A Kinetic and Mechanistic Study

Directory of Open Access Journals (Sweden)

S. Sheik Mansoor

2011-01-01

Full Text Available The kinetics of oxidation of methionine (Met by tripropylammonium fluorochromate (TriPAFC has been studied in the presence of chloroacetic acid in aqueous acetic acid medium. The reaction is first order with respect to methionine, TriPAFC and acid. The reaction rate has been determined at different temperatures and activation parameters calculated. With an increase in the amount of acetic acid in its aqueous mixture, the rate increases. The reaction does not induce polymerization of acrylonitrile. A suitable mechanism has been proposed.

Kinetics and Products of the Reactions of Fluorine Atoms with ClNO and Br2 from 295 to 950 K.

Science.gov (United States)

Bedjanian, Yuri

2017-11-09

The kinetics and products of the reactions of F atoms with Br 2 and ClNO have been studied in a flow reactor coupled with an electron impact ionization mass spectrometer at nearly 2 Torr total pressure of helium and over a wide temperature range, T = 295-950 K. The rate constant of the reaction F + ClNO → products (1) was determined under pseudo-first order conditions, monitoring the kinetics of F atom consumption in excess of ClNO. The measured temperature independent rate constant, k 1 = (1.29 ± 0.13) × 10 -10 cm 3 molecule -1 s -1 (T = 299-950 K), was found to be in excellent agreement with the only previous low temperature study which allowed to recommend the value of k 1 in an extended temperature range, 228-950 K. FCl and Cl atoms were observed as the reactions products (corresponding to two reaction pathways: Cl-atom abstraction and replacement with fluorine atom, respectively) with the independent of temperature, in the range 295-948 K, yields of 0.68 ± 0.10 and 0.32 ± 0.05, respectively. Rate constant of the reaction F + Br 2 (2), k 2 = (1.28 ± 0.20) × 10 -10 cm 3 molecule -1 s -1 , determined using both absolute and relative rate methods, was found to be independent of temperature at T = 299-940 K.

Temperature influence on the reaction kinetics of V(IV)/V(V) in methanesulfonic acid for all-vanadium redox flow battery

International Nuclear Information System (INIS)

Wang, Qiuhong; Daoud, Walid A.

2016-01-01

Highlights: • Diffusion coefficients and standard rate constants of V(IV) and V(V) in MSA at different temperatures are studied. • Carbon-based and metal electrodes are investigated under the same experimental condition at high temperature. • The influence of temperature on reaction kinetics is more significant on carbon-based electrode than metal electrode. • Gold electrode shows inefficient performance in MSA solution. - Abstract: In this study, methanesulfonic acid has been investigated as the supporting electrolyte for vanadium solutions due to the improvement of mass transfer rate and reaction kinetics. Here, we applied different temperatures (0–55 °C) for electrochemical experiments of 0.1 M vanadium ions in 1.0 M MSA electrolyte on gold, platinum and glassy carbon electrodes separately to study the temperature-related kinetics. Considering that electron transfer is the control path for the whole reduction potential window, the rotating disc electrode approach was utilized for the oxidation of V(IV) ions, while the reduction of V(V) ions was studied by cyclic voltammetry. The influence of temperature on charge-transfer resistance and mass transport for both V(IV) and V(V) solutions was studied by electrochemical impedance spectroscopy on glassy carbon electrode. The results showed that the diffusion coefficients in both redox reactions on all electrodes increased with temperature, and most were in the order of 10 −6 cm 2 s −1 . The positive influence of temperature was also observed on the standard rate constants for all conditions in this study, most significantly on the glassy carbon electrode. Comparison between glassy carbon electrode and metal electrodes indicates a promising potential of carbon-based material as electrode for redox flow battery.

ENZYMATIC KINETIC STUDY HYDROLASE FROM CITRUS

Directory of Open Access Journals (Sweden)

Israel Hernández

2015-09-01

Full Text Available In this paper the degrading activity of enzymes derived from orange peels (Citrus x sinensis, grapefruit (Citrus paradise and pineapple (Ananas comosus on the organic matter in wastewater is evaluated. This activity is measured indirectly by quantifying the biochemical oxygen demand (COD before and after degradation process based on a period of time using the HACH DR / 2010, and then the kinetic study was performed by the differential method and integral with the experimental data, obtaining a reaction order of 1 to pectinase (orange, and order 2 for bromelain (pineapple.

Assessment of sorption properties and kinetic reaction of phosphorus reactive material to limit diffuse pollution

Directory of Open Access Journals (Sweden)

Bus Agnieszka

2017-09-01

Full Text Available Assessment of sorption properties and kinetic reaction of phosphorus reactive material to limit diffuse pollution. Polonite® is an effective reactive material (manufactured from opoka rock for removing phosphorus from aqueous solutions. In conducted experiments, Polonite® of grain size of 2–5 mm was used as a potential reactive material which can be used as a filter fulfillment to reduce phosphorus diffuse pollution from agriculture areas. Kinetic and equilibrium studies (performed as a batch experiment were carried out as a function of time to evaluate the sorption properties of the material. The obtained results show that Polonite® effectively removes such contamination. All tested concentrations (0.998, 5.213, 10.965 mg P-PO4·L−1 are characterized by a better fit to pseudo-second kinetic order. The Langmuir isotherm the best reflects the mechanism of adsorption process in case of Polonite® and based on the isotherm, calculated maximum adsorption capacity equals 96.58 mg P-PO4·g−1.

Kinetics of transuranium element oxidation-reduction reactions in solution; Cinetique des reactions d'oxydo-reduction des elements transuraniens en solution

Energy Technology Data Exchange (ETDEWEB)

Gourisse, D [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1966-09-01

A review of the kinetics of U, Np, Pu, Am oxidation-reduction reactions is proposed. The relations between the different activation thermodynamic functions (compensatory effect, formal entropy of the activated complex, magnitude of reactions velocities) are considered. The effects of acidity, ionic strength deuterium and mixed solvents polarity on reactions rates are described. The effect of different anions on reactions rates are explained by variations of the reaction standard free energy and variations of the activation free energy (coulombic interactions) resulting from the complexation of dissolved species by these anions. (author) [French] Une revue systematique de la cinetique des reactions d'oxydo-reduction des elements U, Np, Pu, Am, en solution perchlorique est proposee. Des considerations relatives aux grandeurs thermodynamiques d'activation associees aux actes elementaires (effet de compensation, entropie standard des complexes actives, rapidite des reactions) sont developpees. L'influence de l'acidite, de la force ionique, de l'eau lourde et de la polarite des solvants mixtes sur la vitesse des reactions est decrite. Enfin l'influence des differents anions sur la vitesse des reactions est expliquee par les variations de l'enthalpie libre standard de la reaction et de l'enthalpie libre d'activation (travail des forces electrostatiques) resultant de la complexation des especes dissoutes dans la solution. (auteur)

Kinetic Study on Catalytic Cracking of Rubber Seed (Hevea brasiliensis Oil to Liquid Fuels

Directory of Open Access Journals (Sweden)

Wara Dyah Pita Rengga

2015-03-01

Full Text Available Reaction kinetics of catalytic cracking of rubber seed oil to liquid fuels has been investigated. The reac-tion was performed with sulfuric acid as catalyst at temperatures of 350-450 oC and the ratio of oil-catalyst of 0-2 wt.% for 30-90 minutes. Kinetics was studied using the model of 6-lump parameters. The parameters were rubber seed oil, gasoline, kerosene, diesel, gas, and coke. Analysis of experimen-tal data using regression models to obtain reaction rate constants. Activation energies and pre-exponential factors were then calculated based on the Arrhenius equation. The simulation result illus-trated that the six-lump kinetic model can well predict the product yields of rubber seed oil catalytic cracking. The product has high selectivity for gasoline fraction as liquid fuel and the smallest amount of coke. The constant indicates that secondary reactions occurred in diesel products compared to gaso-line and kerosene. The predicted results indicate that catalytic cracking of rubber seed oil had better be conducted at 450 oC for 90 minutes using 0.5 wt.% catalyst. © 2015 BCREC UNDIP. All rights reservedReceived: 3rd December 2013; Revised: 5th December 2014; Accepted: 7th December 2014How to Cite: Rengga, W.D.P., Handayani, P.A., Kadarwati, S., Feinnudin, A.(2015. Kinetic Study on Catalytic Cracking of Rubber Seed (Hevea brasiliensis Oil  to Liquid Fuels. Bulletin of Chemical Reaction Engineering & Catalysis, 10 (1: 50-60. (doi:10.9767/bcrec.10.1.5852.50-60Permalink/DOI: http://dx.doi.org/10.9767/bcrec.10.1.5852.50-60

The binding of quinone to the photosynthetic reaction centers: kinetics and thermodynamics of reactions occurring at the QB-site in zwitterionic and anionic liposomes.

Science.gov (United States)

Mavelli, Fabio; Trotta, Massimo; Ciriaco, Fulvio; Agostiano, Angela; Giotta, Livia; Italiano, Francesca; Milano, Francesco

2014-07-01

Liposomes represent a versatile biomimetic environment for studying the interaction between integral membrane proteins and hydrophobic ligands. In this paper, the quinone binding to the QB-site of the photosynthetic reaction centers (RC) from Rhodobacter sphaeroides has been investigated in liposomes prepared with either the zwitterionic phosphatidylcholine (PC) or the negatively charged phosphatidylglycerol (PG) to highlight the role of the different phospholipid polar heads. Quinone binding (K Q) and interquinone electron transfer (L AB) equilibrium constants in the two type of liposomes were obtained by charge recombination reaction of QB-depleted RC in the presence of increasing amounts of ubiquinone-10 over the temperature interval 6-35 °C. The kinetic of the charge recombination reactions has been fitted by numerically solving the ordinary differential equations set associated with a detailed kinetic scheme involving electron transfer reactions coupled with quinone release and uptake. The entire set of traces at each temperature was accurately fitted using the sole quinone release constants (both in a neutral and a charge separated state) as adjustable parameters. The temperature dependence of the quinone exchange rate at the QB-site was, hence, obtained. It was found that the quinone exchange regime was always fast for PC while it switched from slow to fast in PG as the temperature rose above 20 °C. A new method was introduced in this paper for the evaluation of constant K Q using the area underneath the charge recombination traces as the indicator of the amount of quinone bound to the QB-site.

Comparative study of kinetic reaction of 4,4′-Methylenebis (2-m ethel cyclo hexyl amine) with dimeric fatty acid c36 by use of a catalyst of phosphoric acid and dioxide manganese

International Nuclear Information System (INIS)

Al-Mohanna, N.; Al-Mohammad, H.

2015-01-01

Kinetic study was carried out on the reaction between 4,4′-Methylenebis (2-methylcyclohexylamine and dimeric fatty acid C 3 6 in molten state by use a catalyst of phosphoric acid and dioxide manganese the reaction was performed at 150 o C, and followed by determining the acid value of the product the polyamidation reaction was found to be of overall a second order until equilibrium state moreover the reaction was faster in the presence of the dioxide manganese polyamidation reaction was automatic where the value of free energy was negative the kinetics of thermal degradation was studied by use of thermogravimetric analysis (TGA) and was found to be of overall a second order and was followed by determining the thermodynamic constants of the thermal degradation reaction melting points and transitional glass in the presence of the catalyst were determined by use of differential calorimetry scanning (DSC) and was found to be close the degree of polymerization number average molecular weight and weight average molecular weight have been calculated during different times we noticed that the relationship between degree of polymerization and number average molecular weight, weight average molecular weight with time is linear until equilibrium state the prepared polyamide involve crystallization and amorphous area this was shown by XRD spectra. (author)

Thermal decomposition of a molecular material {N(n-C4H94[FeIIFeIII(C2O43]}∞ leading to ferrite: A reaction kinetics study

Directory of Open Access Journals (Sweden)

Bhattacharjee Ashis

2013-01-01

Full Text Available A multi-step thermal decomposition of a molecular precursor, {N(n-C4H94[FeIIFeIII(C2O43}∞ has been studied using non-isothermal thermogravimetry (TG measurements in the temperature range 300 to ~800 K at multiple heating rates (5, 10 and 20 K min-1. The thermal decomposition of the oxalate-based complex proceeds stepwise through a series of intermediate reactions. Two different isoconversional methods, namely, improved iterative method and model-free method are employed to evaluate the kinetic parameters: activation energy and rate of reaction, and the most probable reaction mechanism of thermal decomposition is also determined. The different reaction pathways leading to different steps in the TG profile have also been explored which are supplemented by earlier experimental observations of the present authors.

Kinetics and

Directory of Open Access Journals (Sweden)

Mojtaba Ahmadi

2016-11-01

Full Text Available The aqueous degradation of Reactive Yellow 84 (RY84 by potassium peroxydisulfate (K2S2O8 has been studied in laboratory scale experiments. The effect of the initial concentrations of potassium peroxydisulfate and RY84, pH and temperature on RY84 degradation were also examined. Experimental data were analyzed using first and second-order kinetics. The degradation kinetics of RY84 of the potassium peroxydisulfate process followed the second-order reaction kinetics. These rate constants have an extreme values similar to of 9.493 mM−1min−1 at a peroxydisulfate dose of 4 mmol/L. Thermodynamic parameters such as activation (Ea and Gibbs free energy (ΔG° were also evaluated. The negative value of ΔGo and Ea shows the spontaneous reaction natural conditions and exothermic nature.

The reaction kinetics of lithium salt with water vapor

International Nuclear Information System (INIS)

Balooch, M.; Dinh, L.N.; Calef, D.F.

2002-01-01

The interaction of lithium salt (LiH and/or LiD) with water vapor in the partial pressure range of 10 -5 -2657 Pa has been investigated. The reaction probability of water with LiH cleaved in an ultra high vacuum environment was obtained using the modulated molecular beam technique. This probability was 0.11 and independent of LiH surface temperature, suggesting a negligible activation energy for the reaction in agreement with quantum chemical calculations. The value gradually reduced, however, to 0.007 as the surface concentration of oxygen containing product approached full coverage. As the film grew beyond a monolayer, the phase lag of hydrogen product increased from 0 deg. C to 20 deg. C and the reaction probability reduced further until it approached our detection limit (∼10 -4 ). This phase lag was attributed to a diffusion-limited process in this regime. For micrometer thick hydroxide films grown in high moisture concentration environment on LiD and LiH, the reaction probability reduced to ∼4x10 -7 and was independent of exposure time. In this regime of thick hydroxide films (LiOH and/or LiOD), microcracks generated in the films to release stress provided easier pathways for moisture to reach the interface. A modified microscope, capable of both atomic force microscopy and nanoindentation, was also employed to investigate the surface morphology of hydroxide monohydrate (LiOH · H 2 O and/or LiOD · H 2 O) grown on hydroxide at high water vapor partial pressures and the kinetics of this growth

Steady-state isotopic transient kinetic analysis investigation of CO-O2 and CO-NO reactions over a commercial automotive catalyst

International Nuclear Information System (INIS)

Oukaci, R.; Blackmond, D.G.; Goodwin, J.G. Jr.; Gallaher, G.R.

1992-01-01

In this paper, steady-state isotopic transient kinetic analysis (SSITKA) is used to study two model reactions, CO oxidation and CO-NO reactions, on a typical formulation of a three-way auto-catalyst. Under steady-state conditions, abrupt switches in the isotopic composition of CO ( 12 C 16 O/ 13 C 18 O) were carried out to produce isotopic transients in both labeled reactants and products. Along with the determination of the average surface lifetimes and concentrations of reaction intermediates, an analysis of the transient responses along the carbon reaction pathway indicated that the distribution of active sites for the formation of CO 2 was bimodal for both reactions. Furthermore, relatively few surface sites contributed to the overall reaction rate

Kinetics of iron redox reaction in silicate melts: A high temperature Xanes study on an alkali basalt

Energy Technology Data Exchange (ETDEWEB)

Cochain, B; Neuville, D R; Roux, J; Strukelj, E; Richet, P [Physique des Mineraux et Magmas, Geochimie-Cosmochimie, CNRS-IPGP, 4 place Jussieu, 75005 Paris (France); Ligny, D de [Universite Claude Bernard Lyon 1, LPCML, F-69622 Villeurbanne (France); Baudelet, F, E-mail: cochain@ipgp.jussieu.f [Synchrotron SOLEIL, L' Orme des Merisiers, Saint Aubin (France)

2009-11-15

In Earth and Materials sciences, iron is the most important transition element. Glass and melt properties are strongly affected by iron content and redox state with the consequence that some properties (i.e. viscosity, heat capacity, crystallization...) depend not only on the amounts of Fe{sup 2+} and Fe{sup 3+}, but also on the coordination state of these ions. In this work we investigate iron redox reactions through XANES experiments at the K-edge of iron. Using a high-temperature heating device, pre-edge of XANES spectra exhibits definite advantages to make in-situ measurements and to determine the evolution of redox state with time, temperature and composition of synthetic silicate melts. In this study, new kinetics measurements are presented for a basalt melt from the 31,000-BC eruption of the Puy de Lemptegy Volcano in France. These measurements have been made between 773 K and at superliquidus temperatures up to 1923 K.

Kinetics of iron redox reaction in silicate melts: A high temperature Xanes study on an alkali basalt

International Nuclear Information System (INIS)

Cochain, B; Neuville, D R; Roux, J; Strukelj, E; Richet, P; Ligny, D de; Baudelet, F

2009-01-01

In Earth and Materials sciences, iron is the most important transition element. Glass and melt properties are strongly affected by iron content and redox state with the consequence that some properties (i.e. viscosity, heat capacity, crystallization...) depend not only on the amounts of Fe 2+ and Fe 3+ , but also on the coordination state of these ions. In this work we investigate iron redox reactions through XANES experiments at the K-edge of iron. Using a high-temperature heating device, pre-edge of XANES spectra exhibits definite advantages to make in-situ measurements and to determine the evolution of redox state with time, temperature and composition of synthetic silicate melts. In this study, new kinetics measurements are presented for a basalt melt from the 31,000-BC eruption of the Puy de Lemptegy Volcano in France. These measurements have been made between 773 K and at superliquidus temperatures up to 1923 K.

Process and kinetics of the fundamental radiation-electrochemical reactions in the primary coolant loop of nuclear reactors

International Nuclear Information System (INIS)

Kozomara-Maic, S.

1987-06-01

In spite of the rather broad title of this report, its major part is devoted to the corrosion problems at the RA reactor, i.e. causes and consequences of the reactor shutdown in 1979 and 1982. Some problems of reactor chemistry are pointed out because they are significant for future reactor operation. The final conclusion of this report is that corrosion processes in the primary coolant circuit of the nuclear reactor are specific and that radiation effects cannot be excluded when processes and reaction kinetics are investigated. Knowledge about the kinetics of all the chemical reactions occurring in the primary coolant loop are of crucial significance for safe and economical reactor operation [sr

Kinetics and Mechanistic Study of Permanganate Oxidation of Fluorenone Hydrazone in Alkaline Medium

Directory of Open Access Journals (Sweden)

Ahmed Fawzy

2016-01-01

Full Text Available The oxidation kinetics of fluorenone hydrazone (FH using potassium permanganate in alkaline medium were measured at a constant ionic strength of 0.1 mol dm−3 and at 25°C using UV/VIS spectrophotometer. A first-order kinetics has been monitored in the reaction of FH with respect to [permanganate]. Less-than-unit order dependence of the reaction on [FH] and [OH−] was revealed. No pronounced effect on the reaction rate by increasing ionic strength was recorded. Intervention of free radicals was observed in the reaction. The reaction mechanism describing the kinetic results was illustrated which involves formation of 1 : 1 intermediate complex between fluorenone hydrazones and the active species of permanganate. 9H-Fluorenone as the corresponding ketone was found to be the final oxidation product of fluorenone hydrazone as confirmed by GC/MS analysis and FT-IR spectroscopy. The expression rate law for the oxidation reaction was deduced. The reaction constants and mechanism have been evaluated. The activation parameters associated with the rate-limiting step of the reaction, along with the thermodynamic quantities of the equilibrium constants, have been calculated and discussed.

Kinetics in radiation chemistry

International Nuclear Information System (INIS)

Hummel, A.

1987-01-01

In this chapter the authors first briefly review the kinetics of first- and second-order processes for continuous and pulsed irradiation, without taking the effects of nonhomogeneous formation of the species into consideration. They also discuss diffusion controlled reactions under conditions where interactions of more than two particles can be neglected, first the kinetics of the diffusion-controlled reaction of randomly generated species (homogeneous reaction) and then that of isolated pairs of reactants. The latter is often called geminate kinetics when dealing with pairs of oppositely charged species; they shall use this term for the kinetics of isolated pairs in general. In the last section they discuss briefly the kinetics of groups of more than two reactants

Study the oxidation kinetics of uranium using XRD and Rietveld method

Science.gov (United States)

Zhang, Yanzhi; Guan, Weijun; Wang, Qinguo; Wang, Xiaolin; Lai, Xinchun; Shuai, Maobing

2010-03-01

The surface oxidation of uranium metal has been studied by X-ray diffraction (XRD) and Rietveld method in the range of 50~300°C in air. The oxidation processes are analyzed by XRD to determine the extent of surface oxidation and the oxide structure. The dynamics expression for the formation of UO2 was derived. At the beginning, the dynamic expression was nonlinear, but switched to linear subsequently for uranium in air and humid oxygen. That is, the growth kinetics of UO2 can be divided into two stages: nonlinear portion and linear portion. Using the kinetic data of linear portion, the activation energy of reaction between uranium and air was calculated about 46.0 kJ/mol. However the content of oxide as a function of time was linear in humid helium ambience. Contrast the dynamics results, it prove that the absence of oxygen would accelerate the corrosion rate of uranium in the humid gas. We can find that the XRD and Rietveld method are a useful convenient method to estimate the kinetics and thermodynamics of solid-gas reaction.

Multiresponse modelling of the caramelisation reaction

OpenAIRE

Quintas, Mafalda; Guimarães, Carla; Baylina, João; Brandão, Teresa R. S.; Silva, Cristina L.M.

2007-01-01

Multiresponse modelling is a powerful tool for studying complex kinetics of reactions occurring in food products. This modelling technique uses information of reactants and products involved, allowing insightful kinetic parameters estimation and helping in clarifying reaction mechanisms. One example of a complex reaction that occurs in food processing is the caramelisation reaction. Caramelisation is the common name for a group of reactions observed when carbohydrates are exposed to high temp...

Coupling of kinetic Monte Carlo simulations of surface reactions to transport in a fluid for heterogeneous catalytic reactor modeling

International Nuclear Information System (INIS)

Schaefer, C.; Jansen, A. P. J.

2013-01-01

We have developed a method to couple kinetic Monte Carlo simulations of surface reactions at a molecular scale to transport equations at a macroscopic scale. This method is applicable to steady state reactors. We use a finite difference upwinding scheme and a gap-tooth scheme to efficiently use a limited amount of kinetic Monte Carlo simulations. In general the stochastic kinetic Monte Carlo results do not obey mass conservation so that unphysical accumulation of mass could occur in the reactor. We have developed a method to perform mass balance corrections that is based on a stoichiometry matrix and a least-squares problem that is reduced to a non-singular set of linear equations that is applicable to any surface catalyzed reaction. The implementation of these methods is validated by comparing numerical results of a reactor simulation with a unimolecular reaction to an analytical solution. Furthermore, the method is applied to two reaction mechanisms. The first is the ZGB model for CO oxidation in which inevitable poisoning of the catalyst limits the performance of the reactor. The second is a model for the oxidation of NO on a Pt(111) surface, which becomes active due to lateral interaction at high coverages of oxygen. This reaction model is based on ab initio density functional theory calculations from literature.

Kinetics and mechanisms of iron redox reactions in silicate melts: The effects of temperature and alkali cations

Energy Technology Data Exchange (ETDEWEB)

Magnien, V.; Pinet, O. [CEA VALRHO, SCDV/LEBV, F-30207 Bagnols Sur Ceze, (France); Magnien, V.; Neuville, D. R.; Roux, J.; Richet, P. [IPGP, CNRS, Physique des Mineraux et Magmas, F-75252 Paris 05, (France); Cormier, L. [Univ Paris 06, IMPMC, F-75015 Paris, (France); Hazemann, J. L. [CNRS, Inst Neel, F-38043 Grenoble, (France); De Ligny, D. [Univ Lyon 1, LMLC, CNRS, UMR 5620, F-69622 Villeurbanne, (France); Pascarelli, S. [European Synchrotron Radiat Facil, F-38043 Grenoble, (France); Vickridge, I. [Univ Paris 06, INSP, F-75015 Paris, (France)

2008-07-01

The kinetics and the mechanisms of iron redox reactions in molten Fe-bearing pyroxene compositions have been investigated by Raman spectroscopy and X-ray absorption Near Edge Structure (XANES) experiments at the iron K-edge. The former experiments have been made only near the glass transition whereas the latter have also been performed from about 1300 to 2100 K. The same kinetics are observed with both techniques. They are described by characteristic times that depend primarily on temperature and not on the initial redox state. At high temperatures, where both kinds of reactions could be investigated, these times are similar for oxidation and reduction. From these characteristic times we have calculated as a function of temperature and composition a parameter termed effective redox diffusivity. For a given melt, the diffusivities follow two distinct Arrhenius laws, which indicate that the mechanisms of the redox reaction are not the same near the glass transition and at high temperatures. As is now well established, diffusion of divalent cations is the dominant mechanism at low temperatures but the enhanced kinetics observed for alkali-bearing melts indicate that Li{sup +} and Na{sup +} also participate in ionic transport. At super-liquidus temperatures, in contrast, diffusion of oxygen represents the dominant mechanism. (authors)

Kinetics on the reaction of substituted quinolines and p-substituted benzoylchlorides under various pressures

International Nuclear Information System (INIS)

Kim, Young Cheul; Lim, Jong Wan; Choi, Sung Yong; Kim, Se Kyong

1999-01-01

The reaction rates of substituted quinolines(6-CH 3 C 9 H 7 N, C 9 H 7 N) with p-substituted benzoylchlorides(p-CH 3 , p-H, p-NO 2 ) have been measured by conductometry in acetonitrile, and the rate constants are determined at various temperatures (10,15, 20, 25 .deg. C) and pressures(1, 200, 500, 1000bar). From the values of rate constants, the activation parameters(Ea, ΔV ≠ , ΔS ≠ , and ΔG ≠ ) and the pressure dependence of Hammett ρ values were determined. The rate constants increase as a function of temperatures and pressures, and are further increase by introduction the electron donor substituents in nucleophile(p-CH 3 ) or electron acceptor(p-NO 2 ) substituents in substrate. The activation volume, and the activation entropy are all negative. Hammett ρ values are also negative for nucleophile (ρ X ) and positive for the substrate (ρ Y ) over the pressure range studied. The results of kinetic studies for pressure and substituent show that these reactions proceed in typical S N 2 reaction mechanism and 'associative S N 2' in which bond formation favored with increasing pressures

Kinetic Monte Carlo modeling of chemical reactions coupled with heat transfer.

Science.gov (United States)

Castonguay, Thomas C; Wang, Feng

2008-03-28

In this paper, we describe two types of effective events for describing heat transfer in a kinetic Monte Carlo (KMC) simulation that may involve stochastic chemical reactions. Simulations employing these events are referred to as KMC-TBT and KMC-PHE. In KMC-TBT, heat transfer is modeled as the stochastic transfer of "thermal bits" between adjacent grid points. In KMC-PHE, heat transfer is modeled by integrating the Poisson heat equation for a short time. Either approach is capable of capturing the time dependent system behavior exactly. Both KMC-PHE and KMC-TBT are validated by simulating pure heat transfer in a rod and a square and modeling a heated desorption problem where exact numerical results are available. KMC-PHE is much faster than KMC-TBT and is used to study the endothermic desorption of a lattice gas. Interesting findings from this study are reported.

A study of the accelerated zircaloy-4 oxidation reaction with H2O/H2 mixture gas

International Nuclear Information System (INIS)

Kim, Y. S.; Cho, I. J.

2001-01-01

A study of the Zircaloy-4 reaction with H 2 O/H 2 mixture gas is carried out by using TGA (Thermo Gravimetric Apparatus) to estimate the hydrogen embrittlement which can possibly cause catastrophic nuclear fuel rod failure. Reaction rates are measured as a function of H 2 /H 2 O. In the experiments reaction temperature is set at 500 .deg. C and total pressure of the mixture gas is maintained at 1 atm. Experimental results reveal that hydriding and oxidation reaction are competing. In early stage, hydriding kinetics is faster than oxidation, however, oxidant in H 2 O forms oxide on the surface as steam environment is maintained, thus, this growing oxide begins to protect the zirconium base metal against hydrogen permeation. In this second stage, the total kinetic rate follows enhanced oxidation kinetics. In the final stage, it is observed that the oxide is broken down and massive hydriding takes place through the mechanical defects in the oxide, whose kinetics is similar to pure hydriding kinetics. These results are confirmed by SEM and EDX analysis along with hydrogen concentration measurements