Development of LEAP-JET code for sodium-water reaction analysis. Validation by sodium-water reaction tests (SWAT-1R)

International Nuclear Information System (INIS)

Seino, Hiroshi; Hamada, Hirotsugu

2004-03-01

The sodium-water reaction event in an FBR steam generator (SG) has influence on the safety, economical efficiency, etc. of the plant, so that the selection of design base leak (DBL) of the SG is considered as one of the important matters. The clarification of the sodium-water reaction phenomenon and the development of an analysis model are necessary to estimate the sodium-water reaction event with high accuracy and rationality in selecting the DBL. The reaction jet model is pointed out as a part of the necessary improvements to evaluate the overheating tube rupture of large SGs, since the behavior of overheating tube rupture is largely affected by the reaction jet conditions outside the tube. Therefore, LEAP-JET has been developed as an analysis code for the simulation of sodium-water reactions. This document shows the validation of the LEAP-JET code by the Sodium-Water Reaction Test (SWAT-1R). The following results have been obtained: (1) The reaction rate constant, K, is estimated at between 0.001≤K≤0.1 from the LEAP-JET analysis of the SWAT-1R data. (2) The analytical results on the high-temperature region and the behaviors of reaction consumption (Na, H 2 O) and products (H 2 , NaOH, Na 2 O) are considered to be physically reasonable. (3) The LEAP-JET analysis shows the tendency of overestimation in the maximum temperature and temperature distribution of the reaction jet. (4) In the LEAP-JET analysis, the numerical calculation becomes unstably, especially in the mesh containing quite small sodium mass. Therefore, it is necessary to modify the computational algorism to stabilize it and obtain the optimum value of K in sodium-water reactions. (author)

An Attributional Analysis of Reactions to Negative Emotions.

Science.gov (United States)

Karasawa, Kaori

1995-01-01

Three studies examined observers' attributions and reactions to negative emotional displays, as well as expressers' expectations about others' reactions. Analysis revealed that people attribute others' negative emotions equally to situational factors and dispositions, whereas their own emotions are attributed to the situation more than to…

Passivity analysis for uncertain BAM neural networks with time delays and reaction-diffusions

Science.gov (United States)

Zhou, Jianping; Xu, Shengyuan; Shen, Hao; Zhang, Baoyong

2013-08-01

This article deals with the problem of passivity analysis for delayed reaction-diffusion bidirectional associative memory (BAM) neural networks with weight uncertainties. By using a new integral inequality, we first present a passivity condition for the nominal networks, and then extend the result to the case with linear fractional weight uncertainties. The proposed conditions are expressed in terms of linear matrix inequalities, and thus can be checked easily. Examples are provided to demonstrate the effectiveness of the proposed results.

On-line Analysis of Catalytic Reaction Products Using a High-Pressure Tandem Micro-reactor GC/MS.

Science.gov (United States)

Watanabe, Atsushi; Kim, Young-Min; Hosaka, Akihiko; Watanabe, Chuichi; Teramae, Norio; Ohtani, Hajime; Kim, Seungdo; Park, Young-Kwon; Wang, Kaige; Freeman, Robert R

2017-01-01

When a GC/MS system is coupled with a pressurized reactor, the separation efficiency and the retention time are directly affected by the reactor pressure. To keep the GC column flow rate constant irrespective of the reaction pressure, a restrictor capillary tube and an open split interface are attached between the GC injection port and the head of a GC separation column. The capability of the attached modules is demonstrated for the on-line GC/MS analysis of catalytic reaction products of a bio-oil model sample (guaiacol), produced under a pressure of 1 to 3 MPa.

Chemical Demonstrations with Consumer Chemicals: The Black and White Reaction

Science.gov (United States)

Wright, Stephen W.

2002-01-01

A color-change reaction is described in which two colorless solutions are combined to afford a black mixture. Two more colorless solutions are combined to afford a white mixture. The black and white mixtures are then combined to afford a clear, colorless solution. The reaction uses chemicals that are readily available on the retail market: vitamin C, tincture of iodine, vinegar, ammonia, bleach, Epsom salt, and laundry starch.

Specifications for surface reaction analysis apparatus

International Nuclear Information System (INIS)

Teraoka, Yuden; Yoshigoe, Akitaka

2001-03-01

A surface reaction analysis apparatus was installed at the JAERI soft x-ray beamline in the SPring-8 as an experimental end-station for the study of surface chemistry. The apparatus is devoted to the study concerning the influence of translational kinetic energy of incident molecules to chemical reactions on solid surfaces with gas molecules. In order to achieve the research purpose, reactive molecular scattering experiments and photoemission spectroscopic measurements using synchrotron radiation are performed in that apparatus via a supersonic molecular beam generator, an electron energy analyzer and a quadrupole mass analyzer. The detail specifications for the apparatus are described in this report. (author)

Numerical Analysis of Microwave Heating on Saponification Reaction

Science.gov (United States)

Huang, Kama; Jia, Kun

2005-01-01

Currently, microwave is widely used in chemical industry to accelerate chemical reactions. Saponification reaction has important applications in industry; some research results have shown that microwave heating can significantly accelerate the reaction [1]. But so far, no efficient method has been reported for the analysis of the heating process and design of an efficient reactor powered by microwave. In this paper, we present a method to study the microwave heating process on saponification reaction, where the reactant in a test tube is considered as a mixture of dilute solution. According to the preliminary measurement results, the effective permittivity of the mixture is approximately the permittivity of water, but the conductivity, which could change with the reaction, is derived from the reaction equation (RE). The electromagnetic field equation and reaction equation are coupled by the conductivity. Following that, the whole heating processes, which is described by Maxwell's equations, the reaction equation and heat transport equation (HTE), is analyzed by finite difference time domain (FDTD) method. The temperature rising in the test tube are measured and compared with the computational results. Good agreement can be seen between the measured and calculated results.

Analysis of diffusivity of the oscillating reaction components in a microreactor system

Directory of Open Access Journals (Sweden)

Martina Šafranko

2017-01-01

Full Text Available When performing oscillating reactions, periodical changes in the concentrations of reactants, intermediaries, and products take place. Due to the mentioned periodical changes of the concentrations, the information about the diffusivity of the components included into oscillating reactions is very important for the control of the oscillating reactions. Non-linear dynamics makes oscillating reactions very interesting for analysis in different reactor systems. In this paper, the analysis of diffusivity of the oscillating reaction components was performed in a microreactor, with the aim of identifying the limiting component. The geometry of the microreactor microchannel and a well defined flow profile ensure optimal conditions for the diffusion phenomena analysis, because diffusion profiles in a microreactor depend only on the residence time. In this paper, the analysis of diffusivity of the oscillating reaction components was performed in a microreactor equipped with 2 Y-shape inlets and 2 Y-shape outlets, with active volume of V = 4 μL at different residence times.

Structural parameter identifiability analysis for dynamic reaction networks

DEFF Research Database (Denmark)

Davidescu, Florin Paul; Jørgensen, Sten Bay

2008-01-01

method based on Lie derivatives. The proposed systematic two phase methodology is illustrated on a mass action based model for an enzymatically catalyzed reaction pathway network where only a limited set of variables is measured. The methodology clearly pinpoints the structurally identifiable parameters...... where for a given set of measured variables it is desirable to investigate which parameters may be estimated prior to spending computational effort on the actual estimation. This contribution addresses the structural parameter identifiability problem for the typical case of reaction network models....... The proposed analysis is performed in two phases. The first phase determines the structurally identifiable reaction rates based on reaction network stoichiometry. The second phase assesses the structural parameter identifiability of the specific kinetic rate expressions using a generating series expansion...

Isothermal reaction calorimetry as a tool for kinetic analysis

International Nuclear Information System (INIS)

Zogg, Andreas; Stoessel, Francis; Fischer, Ulrich; Hungerbuehler, Konrad

2004-01-01

Reaction calorimetry has found widespread application for thermal and kinetic analysis of chemical reactions in the context of thermal process safety as well as process development. This paper reviews the most important reaction calorimetric principles (heat-flow, heat-balance, power-compensation, and Peltier principle) and their applications in commercial or scientific devices. The discussion focuses on the different dynamic behavior of the main calorimetric principles during an isothermal reaction measurement. Examples of available reaction calorimeters are further compared considering their detection limit, time constant as well as temperature range. In a second part, different evaluation methods for the isothermally measured calorimetric data are reviewed and discussed. The methods will be compared, focusing especially on the fact that reaction calorimetric data always contains additional informations not directly related to the actual chemical reaction such as heat of mixing, heat of phase-transfer/change processes or simple measurement errors. Depending on the evaluation method applied such disturbances have a significant influence on the calculated reaction enthalpies or rate constants

Accelerated Sensitivity Analysis in High-Dimensional Stochastic Reaction Networks.

Science.gov (United States)

Arampatzis, Georgios; Katsoulakis, Markos A; Pantazis, Yannis

2015-01-01

Existing sensitivity analysis approaches are not able to handle efficiently stochastic reaction networks with a large number of parameters and species, which are typical in the modeling and simulation of complex biochemical phenomena. In this paper, a two-step strategy for parametric sensitivity analysis for such systems is proposed, exploiting advantages and synergies between two recently proposed sensitivity analysis methodologies for stochastic dynamics. The first method performs sensitivity analysis of the stochastic dynamics by means of the Fisher Information Matrix on the underlying distribution of the trajectories; the second method is a reduced-variance, finite-difference, gradient-type sensitivity approach relying on stochastic coupling techniques for variance reduction. Here we demonstrate that these two methods can be combined and deployed together by means of a new sensitivity bound which incorporates the variance of the quantity of interest as well as the Fisher Information Matrix estimated from the first method. The first step of the proposed strategy labels sensitivities using the bound and screens out the insensitive parameters in a controlled manner. In the second step of the proposed strategy, a finite-difference method is applied only for the sensitivity estimation of the (potentially) sensitive parameters that have not been screened out in the first step. Results on an epidermal growth factor network with fifty parameters and on a protein homeostasis with eighty parameters demonstrate that the proposed strategy is able to quickly discover and discard the insensitive parameters and in the remaining potentially sensitive parameters it accurately estimates the sensitivities. The new sensitivity strategy can be several times faster than current state-of-the-art approaches that test all parameters, especially in "sloppy" systems. In particular, the computational acceleration is quantified by the ratio between the total number of parameters over the

Accelerated Sensitivity Analysis in High-Dimensional Stochastic Reaction Networks.

Directory of Open Access Journals (Sweden)

Georgios Arampatzis

Full Text Available Existing sensitivity analysis approaches are not able to handle efficiently stochastic reaction networks with a large number of parameters and species, which are typical in the modeling and simulation of complex biochemical phenomena. In this paper, a two-step strategy for parametric sensitivity analysis for such systems is proposed, exploiting advantages and synergies between two recently proposed sensitivity analysis methodologies for stochastic dynamics. The first method performs sensitivity analysis of the stochastic dynamics by means of the Fisher Information Matrix on the underlying distribution of the trajectories; the second method is a reduced-variance, finite-difference, gradient-type sensitivity approach relying on stochastic coupling techniques for variance reduction. Here we demonstrate that these two methods can be combined and deployed together by means of a new sensitivity bound which incorporates the variance of the quantity of interest as well as the Fisher Information Matrix estimated from the first method. The first step of the proposed strategy labels sensitivities using the bound and screens out the insensitive parameters in a controlled manner. In the second step of the proposed strategy, a finite-difference method is applied only for the sensitivity estimation of the (potentially sensitive parameters that have not been screened out in the first step. Results on an epidermal growth factor network with fifty parameters and on a protein homeostasis with eighty parameters demonstrate that the proposed strategy is able to quickly discover and discard the insensitive parameters and in the remaining potentially sensitive parameters it accurately estimates the sensitivities. The new sensitivity strategy can be several times faster than current state-of-the-art approaches that test all parameters, especially in "sloppy" systems. In particular, the computational acceleration is quantified by the ratio between the total number of

Nonlinear analysis of a reaction-diffusion system: Amplitude equations

Energy Technology Data Exchange (ETDEWEB)

Zemskov, E. P., E-mail: zemskov@ccas.ru [Russian Academy of Sciences, Dorodnicyn Computing Center (Russian Federation)

2012-10-15

A reaction-diffusion system with a nonlinear diffusion term is considered. Based on nonlinear analysis, the amplitude equations are obtained in the cases of the Hopf and Turing instabilities in the system. Turing pattern-forming regions in the parameter space are determined for supercritical and subcritical instabilities in a two-component reaction-diffusion system.

Improvement on reaction model for sodium-water reaction jet code and application analysis

International Nuclear Information System (INIS)

Itooka, Satoshi; Saito, Yoshinori; Okabe, Ayao; Fujimata, Kazuhiro; Murata, Shuuichi

2000-03-01

In selecting the reasonable DBL on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on sodium-water reaction (SWR) jet code (LEAP-JET ver.1.30) and application analysis to the water injection tests for confirmation of code propriety were performed. On the improvement of the code, a gas-liquid interface area density model was introduced to develop a chemical reaction model with a little dependence on calculation mesh size. The test calculation using the improved code (LEAP-JET ver.1.40) were carried out with conditions of the SWAT-3·Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results and the influence to analysis result of a model are reasonable. For the application analysis to the water injection tests, water injection behavior and SWR jet behavior analyses on the new SWAT-1 (SWAT-1R) and SWAT-3 (SWAT-3R) tests were performed using the LEAP-BLOW code and the LEAP-JET code. In the application analysis of the LEAP-BLOW code, parameter survey study was performed. As the results, the condition of the injection nozzle diameter needed to simulate the water leak rate was confirmed. In the application analysis of the LEAP-JET code, temperature behavior of the SWR jet was investigated. (author)

Dose Volume Histogram analysis for rectum and urethral reaction of prostate cancer

International Nuclear Information System (INIS)

Yanagi, Takeshi; Tsuji, Hiroshi; Kamada, Tadashi; Tsujii, Hirohiko

2005-01-01

The aim of this study is to evaluate the clinically relevant parameters for rectum and urethral reaction using DVH (dose volume histogram) in carbon ion radiotherapy of prostate cancer. In this year, we studied the urinary reaction mainly. 35 patients with prostate cancer were treated with carbon ion beams between June 1995 and December 1997. The applied dose was escalated from 54.0 GyE to 72.0 GyE in fixed 20 fractions. Clinical urinary reaction and rectum reaction were reviewed using Radiation Therapy Oncology Group (RTOG) scoring system for acute reactions, RTOG/European Organization for Research and Treatment of Cancer (EORTC) scoring system for late reactions. Taking the ROI (region of interest) for DVH of urethra, we used surrogate one that was derived from the observation of MR images. 35 patients were analyzed for acute urinary reaction and 34 for late urinary reaction in the study of this year. DVH analysis suggested difference among the grades for acute and late reactions. These analysis appears to be a useful tool for predicting the urinary reactions. (author)

Development of blow down and sodium-water reaction jet analysis codes-Validation by sodium-water reaction tests (SWAT-1R)

International Nuclear Information System (INIS)

Hiroshi Seino; Akikazu Kurihara; Isao Ono; Koji Jitsu

2005-01-01

Blow down analysis code (LEAP-BLOW) and sodium-water reaction jet analysis code (LEAP-JET) have been developed in order to improve the evaluation method on sodium-water reaction event in the steam generator (SG) of a sodium cooled fast breeder reactor (FBR). The validation analyses by these two codes were carried out using the data of Sodium-Water Reaction Test (SWAT-1R). The following main results have been obtained through this validation: (1) The calculational results by LEAP-BLOW such as internal pressure and water flow rate show good agreement with the results of the SWAT- 1R test. (2) The LEAP-JET code can qualitatively simulate the behavior of sodium-water reaction. However, it is found that the code has tendency to overestimate the maximum temperature of the reaction jet. (authors)

Large-leak sodium-water reaction analysis for steam generators

International Nuclear Information System (INIS)

Sakano, K.; Shindo, Y.; Hori, M.

1975-01-01

The guillotine rupture of 4 tubes is assumed as a design basis regarding the large-leak sodium-water reaction in the system of the MONJU steam generator. Three kinds of analyses were performed with the view to showing the integrity of the steam generator system on the reaction. The first one is the analysis of the initial pressure spike, assuming the initial guillotine rupture of 1 tube. The analysis was performed by utilizing one-dimensional sphere-cylinder model code SWAC-7 and two-dimensional axisymmetric code PISCES 2DL. The second one is the analysis of the secondary peak pressure and its propagation in the system, assuming the instantaneous guillotine rupture of 4 tubes. The third one is the analysis of the dynamic deformation of the steam generator shell. The integrity of the steam generator system was shown by the analyses. (author)

Large-leak sodium-water reaction analysis for steam generators

Energy Technology Data Exchange (ETDEWEB)

Sakano, K; Shindo, Y; Hori, M

1975-07-01

The guillotine rupture of 4 tubes is assumed as a design basis regarding the large-leak sodium-water reaction in the system of the MONJU steam generator. Three kinds of analyses were performed with the view to showing the integrity of the steam generator system on the reaction. The first one is the analysis of the initial pressure spike, assuming the initial guillotine rupture of 1 tube. The analysis was performed by utilizing one-dimensional sphere-cylinder model code SWAC-7 and two-dimensional axisymmetric code PISCES 2DL. The second one is the analysis of the secondary peak pressure and its propagation in the system, assuming the instantaneous guillotine rupture of 4 tubes. The third one is the analysis of the dynamic deformation of the steam generator shell. The integrity of the steam generator system was shown by the analyses. (author)

Automatic simplification of systems of reaction-diffusion equations by a posteriori analysis.

Science.gov (United States)

Maybank, Philip J; Whiteley, Jonathan P

2014-02-01

Many mathematical models in biology and physiology are represented by systems of nonlinear differential equations. In recent years these models have become increasingly complex in order to explain the enormous volume of data now available. A key role of modellers is to determine which components of the model have the greatest effect on a given observed behaviour. An approach for automatically fulfilling this role, based on a posteriori analysis, has recently been developed for nonlinear initial value ordinary differential equations [J.P. Whiteley, Model reduction using a posteriori analysis, Math. Biosci. 225 (2010) 44-52]. In this paper we extend this model reduction technique for application to both steady-state and time-dependent nonlinear reaction-diffusion systems. Exemplar problems drawn from biology are used to demonstrate the applicability of the technique. Copyright © 2014 Elsevier Inc. All rights reserved.

Parallel replica dynamics method for bistable stochastic reaction networks: Simulation and sensitivity analysis

Science.gov (United States)

Wang, Ting; Plecháč, Petr

2017-12-01

Stochastic reaction networks that exhibit bistable behavior are common in systems biology, materials science, and catalysis. Sampling of stationary distributions is crucial for understanding and characterizing the long-time dynamics of bistable stochastic dynamical systems. However, simulations are often hindered by the insufficient sampling of rare transitions between the two metastable regions. In this paper, we apply the parallel replica method for a continuous time Markov chain in order to improve sampling of the stationary distribution in bistable stochastic reaction networks. The proposed method uses parallel computing to accelerate the sampling of rare transitions. Furthermore, it can be combined with the path-space information bounds for parametric sensitivity analysis. With the proposed methodology, we study three bistable biological networks: the Schlögl model, the genetic switch network, and the enzymatic futile cycle network. We demonstrate the algorithmic speedup achieved in these numerical benchmarks. More significant acceleration is expected when multi-core or graphics processing unit computer architectures and programming tools such as CUDA are employed.

Parallel replica dynamics method for bistable stochastic reaction networks: Simulation and sensitivity analysis.

Science.gov (United States)

Wang, Ting; Plecháč, Petr

2017-12-21

Stochastic reaction networks that exhibit bistable behavior are common in systems biology, materials science, and catalysis. Sampling of stationary distributions is crucial for understanding and characterizing the long-time dynamics of bistable stochastic dynamical systems. However, simulations are often hindered by the insufficient sampling of rare transitions between the two metastable regions. In this paper, we apply the parallel replica method for a continuous time Markov chain in order to improve sampling of the stationary distribution in bistable stochastic reaction networks. The proposed method uses parallel computing to accelerate the sampling of rare transitions. Furthermore, it can be combined with the path-space information bounds for parametric sensitivity analysis. With the proposed methodology, we study three bistable biological networks: the Schlögl model, the genetic switch network, and the enzymatic futile cycle network. We demonstrate the algorithmic speedup achieved in these numerical benchmarks. More significant acceleration is expected when multi-core or graphics processing unit computer architectures and programming tools such as CUDA are employed.

[Adverse reaction caused by rabies vaccine in China: a Meta-analysis].

Science.gov (United States)

Zhang, X R; Wu, Z G; Zhang, W S

2017-06-10

Objective: To conduct a Meta-analysis on the rate of adverse reaction related to rabies vaccine, so as to provide reference for rabies vaccine immunization in China. Methods: We electronically searched databases including CNKI, VIP information resource integration service platform, WanFang Data, CBM, PubMed and The Cochrane Library, to collect studies on Chinese people who had received full rabies vaccination and recording all the adverse reactions, from January 2000 to July 2016. Inclusion and exclusion criteria were strictly followed. Meta-analysis for the adverse reaction rate was performed using the R software. Results: A total of 29 related papers had met the inclusion criteria, with no publication bias noticed. A total number of 11 020 cases had adverse reactions, among all the 94 222 respondents, with an incidence of adverse reactions as 1.04 % -47.78 % . The overall incidence rate of adverse reaction was 9.82 % (95 %CI : 7.58 % -12.72 % ). A combined local adverse reaction rate appeared as 12.05 % (95 % CI : 9.26 % -15.69 % ). The systemic adverse reaction rate was 9.06 % (95 %CI : 7.07 % -11.61 % ). The overall adverse reaction rate on aqueous vaccine was 32.39 % (95 %CI : 21.88 % -47.94 % ). Combined adverse reaction rate of freeze dried vaccine appeared as 8.65 % (95 %CI : 4.54 % -16.51 % ). Significant differences were seen between both groups ( P rabies vaccination was higher than the systemic adverse reaction rate. The adverse reaction rate of aqueous rabies vaccine was higher than that of freeze dried rabies vaccine. Our results suggested that the aqueous vaccine should gradually be eliminated.

Comparing transfusion reaction rates for various plasma types: a systematic review and meta-analysis/regression.

Science.gov (United States)

Saadah, Nicholas H; van Hout, Fabienne M A; Schipperus, Martin R; le Cessie, Saskia; Middelburg, Rutger A; Wiersum-Osselton, Johanna C; van der Bom, Johanna G

2017-09-01

We estimated rates for common plasma-associated transfusion reactions and compared reported rates for various plasma types. We performed a systematic review and meta-analysis of peer-reviewed articles that reported plasma transfusion reaction rates. Random-effects pooled rates were calculated and compared between plasma types. Meta-regression was used to compare various plasma types with regard to their reported plasma transfusion reaction rates. Forty-eight studies reported transfusion reaction rates for fresh-frozen plasma (FFP; mixed-sex and male-only), amotosalen INTERCEPT FFP, methylene blue-treated FFP, and solvent/detergent-treated pooled plasma. Random-effects pooled average rates for FFP were: allergic reactions, 92/10 5 units transfused (95% confidence interval [CI], 46-184/10 5 units transfused); febrile nonhemolytic transfusion reactions (FNHTRs), 12/10 5 units transfused (95% CI, 7-22/10 5 units transfused); transfusion-associated circulatory overload (TACO), 6/10 5 units transfused (95% CI, 1-30/10 5 units transfused); transfusion-related acute lung injury (TRALI), 1.8/10 5 units transfused (95% CI, 1.2-2.7/10 5 units transfused); and anaphylactic reactions, 0.8/10 5 units transfused (95% CI, 0-45.7/10 5 units transfused). Risk differences between plasma types were not significant for allergic reactions, TACO, or anaphylactic reactions. Methylene blue-treated FFP led to fewer FNHTRs than FFP (risk difference = -15.3 FNHTRs/10 5 units transfused; 95% CI, -24.7 to -7.1 reactions/10 5 units transfused); and male-only FFP led to fewer cases of TRALI than mixed-sex FFP (risk difference = -0.74 TRALI/10 5 units transfused; 95% CI, -2.42 to -0.42 injuries/10 5 units transfused). Meta-regression demonstrates that the rate of FNHTRs is lower for methylene blue-treated compared with FFP, and the rate of TRALI is lower for male-only than for mixed-sex FFP; whereas no significant differences are observed between plasma types for allergic reactions, TACO

On the rejection-based algorithm for simulation and analysis of large-scale reaction networks

Energy Technology Data Exchange (ETDEWEB)

Thanh, Vo Hong, E-mail: vo@cosbi.eu [The Microsoft Research-University of Trento Centre for Computational and Systems Biology, Piazza Manifattura 1, Rovereto 38068 (Italy); Zunino, Roberto, E-mail: roberto.zunino@unitn.it [Department of Mathematics, University of Trento, Trento (Italy); Priami, Corrado, E-mail: priami@cosbi.eu [The Microsoft Research-University of Trento Centre for Computational and Systems Biology, Piazza Manifattura 1, Rovereto 38068 (Italy); Department of Mathematics, University of Trento, Trento (Italy)

2015-06-28

Stochastic simulation for in silico studies of large biochemical networks requires a great amount of computational time. We recently proposed a new exact simulation algorithm, called the rejection-based stochastic simulation algorithm (RSSA) [Thanh et al., J. Chem. Phys. 141(13), 134116 (2014)], to improve simulation performance by postponing and collapsing as much as possible the propensity updates. In this paper, we analyze the performance of this algorithm in detail, and improve it for simulating large-scale biochemical reaction networks. We also present a new algorithm, called simultaneous RSSA (SRSSA), which generates many independent trajectories simultaneously for the analysis of the biochemical behavior. SRSSA improves simulation performance by utilizing a single data structure across simulations to select reaction firings and forming trajectories. The memory requirement for building and storing the data structure is thus independent of the number of trajectories. The updating of the data structure when needed is performed collectively in a single operation across the simulations. The trajectories generated by SRSSA are exact and independent of each other by exploiting the rejection-based mechanism. We test our new improvement on real biological systems with a wide range of reaction networks to demonstrate its applicability and efficiency.

Free Energy Contribution Analysis Using Response Kernel Approximation: Insights into the Acylation Reaction of a Beta-Lactamase.

Science.gov (United States)

Asada, Toshio; Ando, Kanta; Bandyopadhyay, Pradipta; Koseki, Shiro

2016-09-08

A widely applicable free energy contribution analysis (FECA) method based on the quantum mechanical/molecular mechanical (QM/MM) approximation using response kernel approaches has been proposed to investigate the influences of environmental residues and/or atoms in the QM region on the free energy profile. This method can evaluate atomic contributions to the free energy along the reaction path including polarization effects on the QM region within a dramatically reduced computational time. The rate-limiting step in the deactivation of the β-lactam antibiotic cefalotin (CLS) by β-lactamase was studied using this method. The experimentally observed activation barrier was successfully reproduced by free energy perturbation calculations along the optimized reaction path that involved activation by the carboxylate moiety in CLS. It was found that the free energy profile in the QM region was slightly higher than the isolated energy and that two residues, Lys67 and Lys315, as well as water molecules deeply influenced the QM atoms associated with the bond alternation reaction in the acyl-enzyme intermediate. These facts suggested that the surrounding residues are favorable for the reactant complex and prevent the intermediate from being too stabilized to proceed to the following deacylation reaction. We have demonstrated that the free energy contribution analysis should be a useful method to investigate enzyme catalysis and to facilitate intelligent molecular design.

Relation of expansion due to alkali silica reaction to the degree of reaction measured by SEM image analysis

International Nuclear Information System (INIS)

Haha, M. Ben; Gallucci, E.; Guidoum, A.; Scrivener, K.L.

2007-01-01

Scanning Electron Microscopy Image Analysis (SEM-IA) was used to quantify the degree of alkali silica reaction in affected microbars, mortar and concrete prisms. It was found that the degree of reaction gave a unique correlation with the macroscopic expansion for three different aggregates, stored at three temperatures and with two levels of alkali. The relationships found for the concretes and the mortars overlap when normalised by the aggregate content. This relationship seems to be linear up to a critical reaction degree which coincides with crack initiation within the reactive aggregates

Demonstration sensitivity analysis for RADTRAN III

International Nuclear Information System (INIS)

Neuhauser, K.S.; Reardon, P.C.

1986-10-01

A demonstration sensitivity analysis was performed to: quantify the relative importance of 37 variables to the total incident free dose; assess the elasticity of seven dose subgroups to those same variables; develop density distributions for accident dose to combinations of accident data under wide-ranging variations; show the relationship between accident consequences and probabilities of occurrence; and develop limits for the variability of probability consequence curves

Environmental analysis for pipeline gas demonstration plants

Energy Technology Data Exchange (ETDEWEB)

Stinton, L.H.

1978-09-01

The Department of Energy (DOE) has implemented programs for encouraging the development and commercialization of coal-related technologies, which include coal gasification demonstration-scale activities. In support of commercialization activities the Environmental Analysis for Pipeline Gas Demonstration Plants has been prepared as a reference document to be used in evaluating potential environmental and socioeconomic effects from construction and operation of site- and process-specific projects. Effluents and associated impacts are identified for six coal gasification processes at three contrasting settings. In general, impacts from construction of a high-Btu gas demonstration plant are similar to those caused by the construction of any chemical plant of similar size. The operation of a high-Btu gas demonstration plant, however, has several unique aspects that differentiate it from other chemical plants. Offsite development (surface mining) and disposal of large quantities of waste solids constitute important sources of potential impact. In addition, air emissions require monitoring for trace metals, polycyclic aromatic hydrocarbons, phenols, and other emissions. Potential biological impacts from long-term exposure to these emissions are unknown, and additional research and data analysis may be necessary to determine such effects. Possible effects of pollutants on vegetation and human populations are discussed. The occurrence of chemical contaminants in liquid effluents and the bioaccumulation of these contaminants in aquatic organisms may lead to adverse ecological impact. Socioeconomic impacts are similar to those from a chemical plant of equivalent size and are summarized and contrasted for the three surrogate sites.

Derivatization reactions in the gas—liquid chromatographic analysis of drugs in biological fluids

NARCIS (Netherlands)

Hulshoff, A.; Lingeman, H.

1984-01-01

Alkylation, acylation, silylation and other derivatization reactions applied to the gas chromatographic analysis of drugs in biological matrices are reviewed. Reaction conditions are discussed in relation to reaction mechanisms. Detector-oriented labelling of drugs, and derivatization with chiral

Stability Analysis of a Reaction-Diffusion System Modeling Atherogenesis

KAUST Repository

Ibragimov, Akif; Ritter, Laura; Walton, Jay R.

2010-01-01

This paper presents a linear, asymptotic stability analysis for a reaction-diffusionconvection system modeling atherogenesis, the initiation of atherosclerosis, as an inflammatory instability. Motivated by the disease paradigm articulated by Ross

Nuclear reaction analysis of hydrogen in materials: Principals and applications

International Nuclear Information System (INIS)

Lanford, W.A.

1991-01-01

Analysis for hydrogen in materials is difficult by most traditional analytic methods. Because hydrogen has no Auger transitions, no X-ray transitions, does not neutron activate, and does not backscatter ions, it is invisible in analytical methods based on these effects. In addition, since hydrogen is a universal contaminant in vacuum systems, techniques based on mass spectrometry are difficult unless extreme measures are taken to reduce hydrogen backgrounds. Because of this situation, methods have been developed for analyzing for hydrogen in solid materials based on nuclear reactions between bombarding ions and hydrogen atoms (protons) in the samples. The nuclear reaction methods are now practiced at laboratories around the world. The basic principals of nuclear reaction analysis will be briefly presented. This method will be illustrated by applications to problems ranging from basic physics, to geology, to materials science, and to art history and archeology

Complementing approaches to demonstrate chlorinated solvent biodegradation in a complex pollution plume: mass balance, PCR and compound-specific stable isotope analysis.

OpenAIRE

Courbet Christelle; Rivière Agnès; Jeannottat Simon; Rinaldi Sandro; Hunkeler Daniel; Bendjoudi Hocine; De Marsily Ghislain

2011-01-01

This work describes the use of different complementing methods (mass balance polymerase chain reaction assays and compound specific stable isotope analysis) to demonstrate the existence and effectiveness of biodegradation of chlorinated solvents in an alluvial aquifer. The solvent contaminated site is an old chemical factory located in an alluvial plain in France. As most of the chlorinated contaminants currently found in the groundwater at this site were produced by local industries at vario...

Analysis by nuclear reactions and activations. A current bibliography

International Nuclear Information System (INIS)

Bujdoso, E.

2001-01-01

A current bibliography based on INIS Atomindex with 78 references on Analysis by nuclear reactions and activations has been prepared for year 1998. References are arranged by first authors' name. (N.T.)

Practical lesson of Photosynthesis: A demonstration of Hill reaction in chloroplasts with energy dissipation by fluorescence upon photosystems uncoupling or inhibition by Diuron herbicide

Directory of Open Access Journals (Sweden)

Vadim Ravara Viviani

2016-05-01

Full Text Available During photosynthesis, the photochemical electron transfer process is easily demonstrated by the Hill reaction, where artificial electron acceptors are reduced by active chloroplasts suspensions in the presence of light.  However, the destiny of luminous energy absorbed by chlorophyll molecules in uncoupled or damaged photosystems is not usually demonstrated. Here we provide an adaptation of the classical Hill reaction using intact spinach chloroplasts, which includes the visualization of energy dissipation by fluorescence in lysed chloroplasts, and a dose/effect response in photosystems inhibited by the herbicide DCMU. This laboratory lesson, which is aimed to biochemistry and biophysics for undergraduate courses of Chemistry, Biological, Environmental and Agricultural Sciences, provides the basic photochemical principles using the classical Hill reaction, and photophysical principles through the visualization of energy dissipation by chlorophyll fluorescence,  improving the understanding of the photosynthetic process, and introducing the concept of fluorescence and its applications as bioanalytical tool to monitor photosynthesis in plants and vegetal ecosystems.

Fabricating Simple Wax Screen-Printing Paper-Based Analytical Devices to Demonstrate the Concept of Limiting Reagent in Acid- Base Reactions

Science.gov (United States)

Namwong, Pithakpong; Jarujamrus, Purim; Amatatongchai, Maliwan; Chairam, Sanoe

2018-01-01

In this article, a low-cost, simple, and rapid fabrication of paper-based analytical devices (PADs) using a wax screen-printing method is reported here. The acid-base reaction is implemented in the simple PADs to demonstrate to students the chemistry concept of a limiting reagent. When a fixed concentration of base reacts with a gradually…

Analysis of Skylab IV fluid mechanic science demonstration

Science.gov (United States)

Klett, M. G.; Bourgeois, S. V.

1975-01-01

Several science demonstrations performed on Skylab III and IV were concerned with the behavior of fluid drops free floating in microgravity. These demonstrations, with large liquid drops, included the oscillation, rotation, impact and coalescence, and air injection into the drops. Rayleigh's analysis of the oscillation of spherical drops of a liquid predicts accurately the effect of size and surface tension on the frequency of vibrated water globules in the Skylab demonstration. However, damping occurred much faster than predicted by Lamb's or Scriven's analyses of the damping time for spherical drops. The impact demonstrations indicated that a minimum velocity is necessary to overcome surface forces and effect a coalescence, but a precise criterion for the coalescence of liquids in low g could not be determined.

Integration of Computational and Preparative Techniques to Demonstrate Physical Organic Concepts in Synthetic Organic Chemistry: An Example Using Diels-Alder Reaction

Science.gov (United States)

Palmer, David R. J.

2004-01-01

The Diels-Alder reaction is used as an example for showing the integration of computational and preparative techniques, which help in demonstrating the physical organic concepts in synthetic organic chemistry. These experiments show that the students should not accept the computational results without questioning them and in many Diels-Alder…

Generic Model-Based Tailor-Made Design and Analysis of Biphasic Reaction Systems

DEFF Research Database (Denmark)

Anantpinijwatna, Amata

systems have a broad range of application, such as the manufacture of petroleum based chemicals, pharmaceuticals, and agro-bio products. Major considerations in the design and analysis of biphasic reaction systems are physical and chemical equilibria, kinetic mechanisms, and reaction rates. The primary...... contribution of this thesis is the development of a systematic modelling framework for the biphasic reaction system. The developed framework consists of three modules describing phase equilibria, reactions and mass transfer, and material balances of such processes. Correlative and predictive thermodynamic......Biphasic reaction systems are composed of immiscible aqueous and organic liquid phases where reactants, products, and catalysts are partitioned. These biphasic conditions point to novel synthesis paths, higher yields, and faster reactions, as well as facilitate product separation. The biphasic...

Can Technical Analysis Signals Detect Price Reactions Around Earnings Announcement?: Evidence from Indonesia

OpenAIRE

Dedhy Sulistiawan; Jogiyanto Hartono

2014-01-01

This study examines whether technical analysis signals can detect price reactions before and after earnings announcement dates in Indonesian stock market. Earnings announcements produce reactions, both before and after the announcements. Informed investors may use private information before earnings announcements (Christophe, Ferri and Angel, 2004; Porter, 1992). Using technical analysis signals, this study expects that retail investors (uninformed investors) can detect preannouncements react...

Multifractal scaling analysis of autopoisoning reactions over a rough surface

International Nuclear Information System (INIS)

Chaudhari, Ajay; Yan, Ching-Cher Sanders; Lee, S.-L.

2003-01-01

Decay type diffusion-limited reactions (DLR) over a rough surface generated by a random deposition model were performed. To study the effect of the decay profile on the reaction probability distribution (RPD), multifractal scaling analysis has been carried out. The dynamics of these autopoisoning reactions are controlled by the two parameters in the decay function, namely, the initial sticking probability (P ini ) of every site and the decay rate (m). The smaller the decay rate, the narrower is the range of α values in the α-f(α) multifractal spectrum. The results are compared with the earlier work of DLR over a surface of diffusion-limited aggregation (DLA). We also considered here the autopoisoning reactions over a smooth surface for comparing our results, which show clearly how the roughness affects the chemical reactions. The q-τ(q) multifractal curves for the smooth surface are linear whereas those for the rough surface are nonlinear. The range of α values in the case of a rough surface is wider than that of the smooth surface

Reaction path analysis of sodium-water reaction phenomena in support of chemical reaction model development

International Nuclear Information System (INIS)

Kikuchi, Shin; Ohshima, Hiroyuki; Hashimoto, Kenro

2011-01-01

Computational study of the sodium-water reaction at the gas (water) - liquid (sodium) interface has been carried out using ab initio (first-principle) method. A possible reaction channel has been identified for the stepwise OH bond dissociations of a single water molecule. The energetics including the binding energy of a water molecule to the sodium surface, the activation energies of the bond cleavages, and the reaction energies, have been evaluated, and the rate constants of the first and second OH bond-breakings have been compared. The results are used as the basis for constructing the chemical reaction model used in a multi-dimensional sodium-water reaction code, SERAPHIM, being developed by JAEA toward the safety assessment of the steam generator (SG) in a sodium-cooled fast reactor (SFR). (author)

Analysis of reaction products formed in the gas phase reaction of E,E-2,4-hexadienal with atmospheric oxidants: Reaction mechanisms and atmospheric implications

Science.gov (United States)

Colmenar, I.; Martin, P.; Cabañas, B.; Salgado, S.; Martinez, E.

2018-03-01

An analysis of reaction products for the reaction of E,E-2,4-hexadienal with chlorine atoms (Cl) and OH and NO3 radicals has been carried out at the first time with the aim of obtaining a better understanding of the tropospheric reactivity of α,β-unsaturated carbonyl compounds. Fourier Transform Infrared (FTIR) spectroscopy and Gas Chromatography-Mass Spectrometry with a Time of Flight detector (GC-TOFMS) were used to carry out the qualitative and/or quantitative analyses. Reaction products in gas and particulate phase were observed from the reactions of E,E-2,4- hexadienal with all oxidants. E/Z-Butenedial and maleic anhydride were the main products identified in gas phase. E-butenedial calculated molar yield ranging from 4 to 10%. A significant amount of multifunctional compounds (chloro and hydroxy carbonyls) was identified. These compounds could be formed in particulate phase explaining the ∼90% of unaccounted carbon in gas phase. The reaction with Cl atoms in the presence of NOx with a long reaction time gave Peroxy Acetyl Nitrate (PAN) as an additional product, which is known for being an important specie in the generation of the photochemical smog. Nitrated compounds were the major organic products from the reaction with the NO3 radical. Based on the identified products, the reaction mechanisms have been proposed. In these mechanisms a double bond addition of the atmospheric oxidant at C4/C5 of E,E-2,4-hexadienal is the first step for tropospheric degradation.

Integrating reaction and analysis: investigation of higher-order reactions by cryogenic trapping

Directory of Open Access Journals (Sweden)

Skrollan Stockinger

2013-09-01

Full Text Available A new approach for the investigation of a higher-order reaction by on-column reaction gas chromatography is presented. The reaction and the analytical separation are combined in a single experiment to investigate the Diels–Alder reaction of benzenediazonium-2-carboxylate as a benzyne precursor with various anthracene derivatives, i.e. anthracene, 9-bromoanthracene, 9-anthracenecarboxaldehyde and 9-anthracenemethanol. To overcome limitations of short reaction contact times at elevated temperatures a novel experimental setup was developed involving a cooling trap to achieve focusing and mixing of the reactants at a defined spot in a fused-silica capillary. This trap functions as a reactor within the separation column in the oven of a gas chromatograph. The reactants are sequentially injected to avoid undefined mixing in the injection port. An experimental protocol was developed with optimized injection intervals and cooling times to achieve sufficient conversions at short reaction times. Reaction products were rapidly identified by mass spectrometric detection. This new approach represents a practical procedure to investigate higher-order reactions at an analytical level and it simultaneously provides valuable information for the optimization of the reaction conditions.

Using a CBL Unit, a Temperature Sensor, and a Graphing Calculator to Model the Kinetics of Consecutive First-Order Reactions as Safe In-Class Demonstrations

Science.gov (United States)

Moore-Russo, Deborah A.; Cortes-Figueroa, Jose E.; Schuman, Michael J.

2006-01-01

The use of Calculator-Based Laboratory (CBL) technology, the graphing calculator, and the cooling and heating of water to model the behavior of consecutive first-order reactions is presented, where B is the reactant, I is the intermediate, and P is the product for an in-class demonstration. The activity demonstrates the spontaneous and consecutive…

Physiological environment induce quick response - slow exhaustion reactions

Directory of Open Access Journals (Sweden)

Noriko eHiroi

2011-09-01

Full Text Available In vivo environments are highly crowded and inhomogeneous, which may affect reaction processes in cells. In this study we examined the effects of intracellular crowding and an inhomogeneity on the behavior of in vivo reactions by calculating the spectral dimension (ds, which can be translated into the reaction rate function. We compared estimates of anomaly parameters obtained from Fluorescence Correlation Spectroscopy (FCS data with fractal dimensions derived from Transmission Electron Microscopy (TEM image analysis. FCS analysis indicated that the anomalous property was linked to physiological structure. Subsequent TEM analysis provided an in vivo illustration; soluble molecules likely percolate between intracellular clusters, which are constructed in a self-organizing manner. We estimated a cytoplasmic spectral dimension ds to be 1.39 ± 0.084. This result suggests that in vivo reactions initially run faster than the same reactions in a homogeneous space; this conclusion is consistent with the anomalous character indicated by FCS analysis. We further showed that these results were compatible with our Monte-Carlo simulation in which the anomalous behavior of mobile molecules correlates with the intracellular environment, leading to description as a percolation cluster, as demonstrated using TEM analysis. We confirmed by the simulation that the above-mentioned in vivo like properties are different from those of homogeneously concentrated environments. Additionally, simulation results indicated that crowding level of an environment might affect diffusion rate of reactant. Such knowledge of the spatial information enables us to construct realistic models for in vivo diffusion and reaction systems.

Analysis of partial and total inelasticities obtained from inclusive reactions

International Nuclear Information System (INIS)

Bellandi, J.; Covolan, R.; Costa, C.G.; Montanha, J.; Mundim, L.M.

1994-01-01

An independent analysis of model for energetic dependence on inelasticity is presented, from experimental data of pp → c X (c = π +- , Κ +- , p +- ) type inclusive reactions. 6 refs., 2 figs., 1 tab

Derivation of the reduced reaction mechanisms of ozone depletion events in the Arctic spring by using concentration sensitivity analysis and principal component analysis

Directory of Open Access Journals (Sweden)

L. Cao

2016-12-01

Full Text Available The ozone depletion events (ODEs in the springtime Arctic have been investigated since the 1980s. It is found that the depletion of ozone is highly associated with an auto-catalytic reaction cycle, which involves mostly the bromine-containing compounds. Moreover, bromide stored in various substrates in the Arctic such as the underlying surface covered by ice and snow can be also activated by the absorbed HOBr. Subsequently, this leads to an explosive increase of the bromine amount in the troposphere, which is called the “bromine explosion mechanism”. In the present study, a reaction scheme representing the chemistry of ozone depletion and halogen release is processed with two different mechanism reduction approaches, namely, the concentration sensitivity analysis and the principal component analysis. In the concentration sensitivity analysis, the interdependence of the mixing ratios of ozone and principal bromine species on the rate of each reaction in the ODE mechanism is identified. Furthermore, the most influential reactions in different time periods of ODEs are also revealed. By removing 11 reactions with the maximum absolute values of sensitivities lower than 10 %, a reduced reaction mechanism of ODEs is derived. The onsets of each time period of ODEs in simulations using the original reaction mechanism and the reduced reaction mechanism are identical while the maximum deviation of the mixing ratio of principal bromine species between different mechanisms is found to be less than 1 %. By performing the principal component analysis on an array of the sensitivity matrices, the dependence of a particular species concentration on a combination of the reaction rates in the mechanism is revealed. Redundant reactions are indicated by principal components corresponding to small eigenvalues and insignificant elements in principal components with large eigenvalues. Through this investigation, aside from the 11 reactions identified as

Thermogravimetric analysis of the beryllium/steam reaction

Energy Technology Data Exchange (ETDEWEB)

Druyts, Frank E-mail: fdruyts@sckcen.be; Iseghem, Pierre van

2000-11-01

In view of the safety assessment of new fusion reactor designs, kinetic data are needed on the beryllium/steam reaction. Therefore, thermogravimetric analysis was used to determine the reactivity of beryllium in steam as a function of temperature, irradiation history and porosity of the samples. To this purpose, reference unirradiated S-200 VHP beryllium samples were compared with specimens irradiated in the BR2 reactor up to fast neutron fluences (E>1 MeV) of respectively 1.6x10{sup 21} n cm{sup -2} (resulting in a helium content of 300 appm He and a theoretical density of 99.9%) and 4x10{sup 22} n cm{sup -2} (21000 appm He, 97.2% theoretical density). Kinetics were parabolic for all tested beryllium types at 600 deg. C. At 700 deg. C, kinetics were parabolic for the unirradiated and irradiated 99.9% dense beryllium, and accelerating/linear for the irradiated 97.2% material. At 800 deg. C, all samples showed accelerating/linear behaviour. There was no influence of porosity on the reaction rate of beryllium in steam within the limited investigated density range, except at 700 deg. C, where the measured reaction rate for the irradiated 97.2% dense samples is an order of magnitude higher than for the irradiated 99.9% dense specimens.

Use of deuteron-induced nuclear reactions for quantitative surface analysis

International Nuclear Information System (INIS)

Simpson, J.C.B.; Earwaker, L.G.

1986-01-01

A summary of the basic features of nuclear reaction analysis is given; particular emphasis is placed on quantitative light element determination using (d,p) and (d,α) reactions. The experimental apparatus is also described, with reference to the 3MV Dynamitron accelerator at the University of Birmingham Radiation Centre. Finally, a set of standard (d, p) spectra for the elements Z=3 to Z=17, using 2 MeV incident deuterons, is included together with examples of the more useful of the (d,α) spectra. (orig.)

Ion beam analysis - development and application of nuclear reaction analysis methods, in particular at a nuclear microprobe

International Nuclear Information System (INIS)

Sjoeland, K.A.

1996-11-01

This thesis treats the development of Ion Beam Analysis methods, principally for the analysis of light elements at a nuclear microprobe. The light elements in this context are defined as having an atomic number less than approx. 13. The work reported is to a large extent based on multiparameter methods. Several signals are recorded simultaneously, and the data can be effectively analyzed to reveal structures that can not be observed through one-parameter collection. The different techniques are combined in a new set-up at the Lund Nuclear Microprobe. The various detectors for reaction products are arranged in such a way that they can be used for the simultaneous analysis of hydrogen, lithium, boron and fluorine together with traditional PIXE analysis and Scanning Transmission Ion Microscopy as well as photon-tagged Nuclear Reaction Analysis. 48 refs

Automatized Assessment of Protective Group Reactivity: A Step Toward Big Reaction Data Analysis.

Science.gov (United States)

Lin, Arkadii I; Madzhidov, Timur I; Klimchuk, Olga; Nugmanov, Ramil I; Antipin, Igor S; Varnek, Alexandre

2016-11-28

We report a new method to assess protective groups (PGs) reactivity as a function of reaction conditions (catalyst, solvent) using raw reaction data. It is based on an intuitive similarity principle for chemical reactions: similar reactions proceed under similar conditions. Technically, reaction similarity can be assessed using the Condensed Graph of Reaction (CGR) approach representing an ensemble of reactants and products as a single molecular graph, i.e., as a pseudomolecule for which molecular descriptors or fingerprints can be calculated. CGR-based in-house tools were used to process data for 142,111 catalytic hydrogenation reactions extracted from the Reaxys database. Our results reveal some contradictions with famous Greene's Reactivity Charts based on manual expert analysis. Models developed in this study show high accuracy (ca. 90%) for predicting optimal experimental conditions of protective group deprotection.

Reactivity of Single-Walled Carbon Nanotubes in the Diels-Alder Cycloaddition Reaction: Distortion-Interaction Analysis along the Reaction Pathway.

Science.gov (United States)

Li, Yingzi; Osuna, Sílvia; Garcia-Borràs, Marc; Qi, Xiaotian; Liu, Song; Houk, Kendall N; Lan, Yu

2016-08-26

Diels-Alder cycloaddition is one of the most powerful tools for the functionalization of single-walled carbon nanotubes (SWCNTs). Density functional theory at the B3-LYP level of theory has been used to investigate the reactivity of different-diameter SWCNTs (4-9,5) in Diels-Alder reactions with 1,3-butadiene; the reactivity was found to decrease with increasing SWCNT diameter. Distortion/interaction analysis along the whole reaction pathway was found to be a better way to explore the reactivity of this type of reaction. The difference in interaction energy along the reaction pathway is larger than that of the corresponding distortion energy. However, the distortion energy plots for these reactions show the same trend. Therefore, the formation of the transition state can be determined from the interaction energy. A lower interaction energy leads to an earlier transition state, which indicates a lower activation energy. The computational results also indicate that the original distortion of the SWCNTs leads to an increase in the reactivity of the SWCNTs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Coupled-reaction-channel analysis of the (d,6Li) reaction on 24Mg and 26Mg to low-lying states

International Nuclear Information System (INIS)

Oelert, W.

1986-01-01

Experimental spectroscopic factors of the alpha-transfer reaction on nuclei of the sd-shell show rather strong inconsistencies and scatter much more strongly than explainable by the quoted errors. The poorer the quality of agreement between experimental and theoretical angular distribution shapes, the more inconsistent the comparison of spectroscopic factors either between different experiments or between theory and experiment. In view of the strong deformation of nuclei in the lower part of the sd-shell, higher-order reaction mechanisms are expected. A coupled-reaction-channel analysis for the transitions to the 0 + , 2 + , and 4 + states of the ground-state bands in 20 Ne and 22 Ne excited via the (d, 6 Li) reaction yields good agreement between experimental and theoretical angular distribution shapes as well as spectroscopic information. (orig.)

Feasibility and demonstration of a cloud-based RIID analysis system

Energy Technology Data Exchange (ETDEWEB)

Wright, Michael C., E-mail: wrightmc@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Hertz, Kristin L.; Johnson, William C. [Sandia National Laboratories, Livermore, CA 94551 (United States); Sword, Eric D.; Younkin, James R. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Sadler, Lorraine E. [Sandia National Laboratories, Livermore, CA 94551 (United States)

2015-06-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed. - Highlights: • A prototype cloud-based RIID analysis system was implemented and demonstrated. • A cloud-based system was shown to be feasible with currently available technology. • A system study identified the operational characteristics required by the users. • The system study showed that the user community could derive significant benefit. • An architecture was defined for field testing by users in relevant environments.

Feasibility and demonstration of a cloud-based RIID analysis system

International Nuclear Information System (INIS)

Wright, Michael C.; Hertz, Kristin L.; Johnson, William C.; Sword, Eric D.; Younkin, James R.; Sadler, Lorraine E.

2015-01-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed. - Highlights: • A prototype cloud-based RIID analysis system was implemented and demonstrated. • A cloud-based system was shown to be feasible with currently available technology. • A system study identified the operational characteristics required by the users. • The system study showed that the user community could derive significant benefit. • An architecture was defined for field testing by users in relevant environments

Regression analysis of a chemical reaction fouling model

International Nuclear Information System (INIS)

Vasak, F.; Epstein, N.

1996-01-01

A previously reported mathematical model for the initial chemical reaction fouling of a heated tube is critically examined in the light of the experimental data for which it was developed. A regression analysis of the model with respect to that data shows that the reference point upon which the two adjustable parameters of the model were originally based was well chosen, albeit fortuitously. (author). 3 refs., 2 tabs., 2 figs

Parametric sensitivity analysis for biochemical reaction networks based on pathwise information theory.

Science.gov (United States)

Pantazis, Yannis; Katsoulakis, Markos A; Vlachos, Dionisios G

2013-10-22

Stochastic modeling and simulation provide powerful predictive methods for the intrinsic understanding of fundamental mechanisms in complex biochemical networks. Typically, such mathematical models involve networks of coupled jump stochastic processes with a large number of parameters that need to be suitably calibrated against experimental data. In this direction, the parameter sensitivity analysis of reaction networks is an essential mathematical and computational tool, yielding information regarding the robustness and the identifiability of model parameters. However, existing sensitivity analysis approaches such as variants of the finite difference method can have an overwhelming computational cost in models with a high-dimensional parameter space. We develop a sensitivity analysis methodology suitable for complex stochastic reaction networks with a large number of parameters. The proposed approach is based on Information Theory methods and relies on the quantification of information loss due to parameter perturbations between time-series distributions. For this reason, we need to work on path-space, i.e., the set consisting of all stochastic trajectories, hence the proposed approach is referred to as "pathwise". The pathwise sensitivity analysis method is realized by employing the rigorously-derived Relative Entropy Rate, which is directly computable from the propensity functions. A key aspect of the method is that an associated pathwise Fisher Information Matrix (FIM) is defined, which in turn constitutes a gradient-free approach to quantifying parameter sensitivities. The structure of the FIM turns out to be block-diagonal, revealing hidden parameter dependencies and sensitivities in reaction networks. As a gradient-free method, the proposed sensitivity analysis provides a significant advantage when dealing with complex stochastic systems with a large number of parameters. In addition, the knowledge of the structure of the FIM can allow to efficiently address

Statistical analysis of activation and reaction energies with quasi-variational coupled-cluster theory

Science.gov (United States)

Black, Joshua A.; Knowles, Peter J.

2018-06-01

The performance of quasi-variational coupled-cluster (QV) theory applied to the calculation of activation and reaction energies has been investigated. A statistical analysis of results obtained for six different sets of reactions has been carried out, and the results have been compared to those from standard single-reference methods. In general, the QV methods lead to increased activation energies and larger absolute reaction energies compared to those obtained with traditional coupled-cluster theory.

Substrate-Coated Illumination Droplet Spray Ionization: Real-Time Monitoring of Photocatalytic Reactions

Science.gov (United States)

Zhang, Hong; Li, Na; Zhao, Dandan; Jiang, Jie; You, Hong

2017-09-01

Real-time monitoring of photocatalytic reactions facilitates the elucidation of the mechanisms of the reactions. However, suitable tools for real-time monitoring are lacking. Herein, a novel method based on droplet spray ionization named substrate-coated illumination droplet spray ionization (SCI-DSI) for direct analysis of photocatalytic reaction solution is reported. SCI-DSI addresses many of the analytical limitations of electrospray ionization (ESI) for analysis of photocatalytic-reaction intermediates, and has potential for both in situ analysis and real-time monitoring of photocatalytic reactions. In SCI-DSI-mass spectrometry (MS), a photocatalytic reaction occurs by loading sample solutions onto the substrate-coated cover slip and by applying UV light above the modified slip; one corner of this slip adjacent to the inlet of a mass spectrometer is the high-electric-field location for launching a charged-droplet spray. After both testing and optimizing the performance of SCI-DSI, the value of this method for in situ analysis and real-time monitoring of photocatalytic reactions was demonstrated by the removal of cyclophosphamide (CP) in TiO2/UV. Reaction times ranged from seconds to minutes, and the proposed reaction intermediates were captured and identified by tandem mass spectrometry. Moreover, the free hydroxyl radical (·OH) was identified as the main radicals for CP removal. These results show that SCI-DSI is suitable for in situ analysis and real-time monitoring of CP removal under TiO2-based photocatalytic reactions. SCI-DSI is also a potential tool for in situ analysis and real-time assessment of the roles of radicals during CP removal under TiO2-based photocatalytic reactions. Graphical Abstract[Figure not available: see fulltext.

Surface reactivity and layer analysis of chemisorbed reaction films in ...

Indian Academy of Sciences (India)

Administrator

Surface reactivity and layer analysis of chemisorbed reaction films in ... in the nitrogen environment. Keywords. Surface reactivity ... sium (Na–K) compounds in the coating or core of the ..... Barkshire I R, Pruton M and Smith G C 1995 Appl. Sur.

Demonstration Project. Consumer reactions to peak prices

International Nuclear Information System (INIS)

Lindskoug, Stefan

2006-06-01

The purpose and aim of the project is to look at the risk of capacity shortage in the Swedish electricity supply system during excessively cold periods of weather. A risk that has increased in recent years. A growing number of analysts emphasize the importance of high spot prices actually leading to a reduction in demand. Through increased consumer sensitivity as regards pricing, the power system can be run safely with smaller generation reserves. In addition, market price fluctuation is estimated to become more stable and predictable. The purpose of the Demonstration Project is to demonstrate methods or business concepts that lead to the demand for electricity on a national level being reduced at times of high spot prices. The need for the measures to be profitable for the parties involved is an important starting point. A general problem associated with research and development projects is that the participants feel selected and special attention is paid them, hence they will make an extra effort to improve the results. We were aware of this fact when setting up the trials, which is why we introduced the trials as an offer from the electricity supplier to take part in a commercial assessment using a new price list. For this reason we concealed the marked research aim with Elforsk as a backer. Evaluating the results of questionnaires and detailed interviews does not give cause to suppose the results are in any way affected by such conditions. The conclusion of this project is that controlling load at the customer end is an economic alternative to the investment of new production resources

Determination and theoretical analysis of the differential cross sections of the 2H(d,p) reaction at energies and detection angles suitable for NRA (Nuclear Reaction Analysis)

International Nuclear Information System (INIS)

Paneta, V.; Axiotis, M.; Lagoyannis, A.; Gastis, P.; Kokkoris, M.; Vlastou, R.; Kontos, A.; Mayer, M.; Misaelides, P.; Perdikakis, G.

2014-01-01

The accurate determination of deuteron depth profile presents a strong analytical challenge for all the principal IBA (Ion Beam Analysis) techniques. As far as NRA (Nuclear Reaction Analysis) is concerned, the 2 H(d,p) reaction, seems to be a promising candidate, especially in the case of complex matrices, or for the study of deep-implanted deuteron layers. In the present work differential cross-section values for the 2 H(d,p) reaction have been determined at 140, 160 and 170 degrees, for E d (lab) = 900-1600 keV, with an energy step of 50 keV, using a well-characterized, thin C:D target deposited on a polished Si wafer. The detection system consisted of 3 silicon surface barrier (SSB) detectors (thickness of 1000 μm) placed at a distance of about 11-13 cm from the target, at the appropriate angles. The experimental results were analyzed using the R-matrix calculations code AZURE. The results, in graphical and tabular form, will soon be available to the scientific community through IBANDL

iADRs: towards online adverse drug reaction analysis.

Science.gov (United States)

Lin, Wen-Yang; Li, He-Yi; Du, Jhih-Wei; Feng, Wen-Yu; Lo, Chiao-Feng; Soo, Von-Wun

2012-12-01

Adverse Drug Reaction (ADR) is one of the most important issues in the assessment of drug safety. In fact, many adverse drug reactions are not discovered during limited pre-marketing clinical trials; instead, they are only observed after long term post-marketing surveillance of drug usage. In light of this, the detection of adverse drug reactions, as early as possible, is an important topic of research for the pharmaceutical industry. Recently, large numbers of adverse events and the development of data mining technology have motivated the development of statistical and data mining methods for the detection of ADRs. These stand-alone methods, with no integration into knowledge discovery systems, are tedious and inconvenient for users and the processes for exploration are time-consuming. This paper proposes an interactive system platform for the detection of ADRs. By integrating an ADR data warehouse and innovative data mining techniques, the proposed system not only supports OLAP style multidimensional analysis of ADRs, but also allows the interactive discovery of associations between drugs and symptoms, called a drug-ADR association rule, which can be further developed using other factors of interest to the user, such as demographic information. The experiments indicate that interesting and valuable drug-ADR association rules can be efficiently mined.

Performance demonstration program plan for analysis of simulated headspace gases

International Nuclear Information System (INIS)

1995-06-01

The Performance Demonstration Program (PDP) for analysis of headspace gases will consist of regular distribution and analyses of test standards to evaluate the capability for analyzing VOCs, hydrogen, and methane in the headspace of transuranic (TRU) waste throughout the Department of Energy (DOE) complex. Each distribution is termed a PDP cycle. These evaluation cycles will provide an objective measure of the reliability of measurements performed for TRU waste characterization. Laboratory performance will be demonstrated by the successful analysis of blind audit samples of simulated TRU waste drum headspace gases according to the criteria set within the text of this Program Plan. Blind audit samples (hereinafter referred to as PDP samples) will be used as an independent means to assess laboratory performance regarding compliance with the QAPP QAOs. The concentration of analytes in the PDP samples will encompass the range of concentrations anticipated in actual waste characterization gas samples. Analyses which are required by the WIPP to demonstrate compliance with various regulatory requirements and which are included in the PDP must be performed by laboratories which have demonstrated acceptable performance in the PDP

Automatic NMR-based identification of chemical reaction types in mixtures of co-occurring reactions.

Science.gov (United States)

Latino, Diogo A R S; Aires-de-Sousa, João

2014-01-01

The combination of chemoinformatics approaches with NMR techniques and the increasing availability of data allow the resolution of problems far beyond the original application of NMR in structure elucidation/verification. The diversity of applications can range from process monitoring, metabolic profiling, authentication of products, to quality control. An application related to the automatic analysis of complex mixtures concerns mixtures of chemical reactions. We encoded mixtures of chemical reactions with the difference between the (1)H NMR spectra of the products and the reactants. All the signals arising from all the reactants of the co-occurring reactions were taken together (a simulated spectrum of the mixture of reactants) and the same was done for products. The difference spectrum is taken as the representation of the mixture of chemical reactions. A data set of 181 chemical reactions was used, each reaction manually assigned to one of 6 types. From this dataset, we simulated mixtures where two reactions of different types would occur simultaneously. Automatic learning methods were trained to classify the reactions occurring in a mixture from the (1)H NMR-based descriptor of the mixture. Unsupervised learning methods (self-organizing maps) produced a reasonable clustering of the mixtures by reaction type, and allowed the correct classification of 80% and 63% of the mixtures in two independent test sets of different similarity to the training set. With random forests (RF), the percentage of correct classifications was increased to 99% and 80% for the same test sets. The RF probability associated to the predictions yielded a robust indication of their reliability. This study demonstrates the possibility of applying machine learning methods to automatically identify types of co-occurring chemical reactions from NMR data. Using no explicit structural information about the reactions participants, reaction elucidation is performed without structure elucidation of

Automatic NMR-based identification of chemical reaction types in mixtures of co-occurring reactions.

Directory of Open Access Journals (Sweden)

Diogo A R S Latino

Full Text Available The combination of chemoinformatics approaches with NMR techniques and the increasing availability of data allow the resolution of problems far beyond the original application of NMR in structure elucidation/verification. The diversity of applications can range from process monitoring, metabolic profiling, authentication of products, to quality control. An application related to the automatic analysis of complex mixtures concerns mixtures of chemical reactions. We encoded mixtures of chemical reactions with the difference between the (1H NMR spectra of the products and the reactants. All the signals arising from all the reactants of the co-occurring reactions were taken together (a simulated spectrum of the mixture of reactants and the same was done for products. The difference spectrum is taken as the representation of the mixture of chemical reactions. A data set of 181 chemical reactions was used, each reaction manually assigned to one of 6 types. From this dataset, we simulated mixtures where two reactions of different types would occur simultaneously. Automatic learning methods were trained to classify the reactions occurring in a mixture from the (1H NMR-based descriptor of the mixture. Unsupervised learning methods (self-organizing maps produced a reasonable clustering of the mixtures by reaction type, and allowed the correct classification of 80% and 63% of the mixtures in two independent test sets of different similarity to the training set. With random forests (RF, the percentage of correct classifications was increased to 99% and 80% for the same test sets. The RF probability associated to the predictions yielded a robust indication of their reliability. This study demonstrates the possibility of applying machine learning methods to automatically identify types of co-occurring chemical reactions from NMR data. Using no explicit structural information about the reactions participants, reaction elucidation is performed without structure

[Incidence rate of adverse reaction/event by Qingkailing injection: a Meta-analysis of single rate].

Science.gov (United States)

Ai, Chun-ling; Xie, Yan-ming; Li, Ming-quan; Wang, Lian-xin; Liao, Xing

2015-12-01

To systematically review the incidence rate of adverse drug reaction/event by Qingkailing injection. Such databases as the PubMed, EMbase, the Cochrane library, CNKI, VIP WanFang data and CBM were searched by computer from foundation to July 30, 2015. Two reviewers independently screened literature according to the inclusion and exclusion criteria, extracted data and cross check data. Then, Meta-analysis was performed by using the R 3.2.0 software, subgroup sensitivity analysis was performed based on age, mode of medicine, observation time and research quality. Sixty-three studies involving 9,793 patients with Qingkailing injection were included, 367 cases of adverse reactions/events were reported in total. The incidence rate of adverse reaction in skin and mucosa group was 2% [95% CI (0.02; 0.03)]; the digestive system adverse reaction was 6% [95% CI(0.05; 0.07); the injection site adverse reaction was 4% [95% CI (0.02; 0.07)]. In the digestive system as the main types of adverse reactions/events, incidence of children and adults were 4.6% [0.021 1; 0.097 7] and 6.9% [0.053 5; 0.089 8], respectively. Adverse reactions to skin and mucous membrane damage as the main performance/event type, the observation time > 7 days and ≤ 7 days incidence of 3% [0.012 9; 0.068 3] and 1.9% [0.007 8; 0.046 1], respectively. Subgroup analysis showed that different types of adverse reactions, combination in the incidence of adverse reactions/events were higher than that of single drug, the difference was statistically significant (P reactions occur, and clinical rational drug use, such as combination, age and other fators, and the influence factors vary in different populations. Therefore, clinical doctors for children and the elderly use special care was required for a clear and open spirit injection, the implementation of individualized medication.

Feasibility and demonstration of a cloud-based RIID analysis system

Science.gov (United States)

Wright, Michael C.; Hertz, Kristin L.; Johnson, William C.; Sword, Eric D.; Younkin, James R.; Sadler, Lorraine E.

2015-06-01

A significant limitation in the operational utility of handheld and backpack radioisotope identifiers (RIIDs) is the inability of their onboard algorithms to accurately and reliably identify the isotopic sources of the measured gamma-ray energy spectrum. A possible solution is to move the spectral analysis computations to an external device, the cloud, where significantly greater capabilities are available. The implementation and demonstration of a prototype cloud-based RIID analysis system have shown this type of system to be feasible with currently available communication and computational technology. A system study has shown that the potential user community could derive significant benefits from an appropriately implemented cloud-based analysis system and has identified the design and operational characteristics required by the users and stakeholders for such a system. A general description of the hardware and software necessary to implement reliable cloud-based analysis, the value of the cloud expressed by the user community, and the aspects of the cloud implemented in the demonstrations are discussed.

Multilayer Network Analysis of Nuclear Reactions

Science.gov (United States)

Zhu, Liang; Ma, Yu-Gang; Chen, Qu; Han, Ding-Ding

2016-08-01

The nuclear reaction network is usually studied via precise calculation of differential equation sets, and much research interest has been focused on the characteristics of nuclides, such as half-life and size limit. In this paper, however, we adopt the methods from both multilayer and reaction networks, and obtain a distinctive view by mapping all the nuclear reactions in JINA REACLIB database into a directed network with 4 layers: neutron, proton, 4He and the remainder. The layer names correspond to reaction types decided by the currency particles consumed. This combined approach reveals that, in the remainder layer, the β-stability has high correlation with node degree difference and overlapping coefficient. Moreover, when reaction rates are considered as node strength, we find that, at lower temperatures, nuclide half-life scales reciprocally with its out-strength. The connection between physical properties and topological characteristics may help to explore the boundary of the nuclide chart.

Analysis techniques for background rejection at the Majorana Demonstrator

Energy Technology Data Exchange (ETDEWEB)

Cuestra, Clara [University of Washington; Rielage, Keith Robert [Los Alamos National Laboratory; Elliott, Steven Ray [Los Alamos National Laboratory; Xu, Wenqin [Los Alamos National Laboratory; Goett, John Jerome III [Los Alamos National Laboratory

2015-06-11

The MAJORANA Collaboration is constructing the MAJORANA DEMONSTRATOR, an ultra-low background, 40-kg modular HPGe detector array to search for neutrinoless double beta decay in ⁷⁶Ge. In view of the next generation of tonne-scale Ge-based 0νββ-decay searches that will probe the neutrino mass scale in the inverted-hierarchy region, a major goal of the MAJORANA DEMONSTRATOR is to demonstrate a path forward to achieving a background rate at or below 1 count/tonne/year in the 4 keV region of interest around the Q-value at 2039 keV. The background rejection techniques to be applied to the data include cuts based on data reduction, pulse shape analysis, event coincidences, and time correlations. The Point Contact design of the DEMONSTRATOR's germanium detectors allows for significant reduction of gamma background.

AEP Ohio gridSMART Demonstration Project Real-Time Pricing Demonstration Analysis

Energy Technology Data Exchange (ETDEWEB)

Widergren, Steven E.; Subbarao, Krishnappa; Fuller, Jason C.; Chassin, David P.; Somani, Abhishek; Marinovici, Maria C.; Hammerstrom, Janelle L.

2014-02-01

This report contributes initial findings from an analysis of significant aspects of the gridSMART® Real-Time Pricing (RTP) – Double Auction demonstration project. Over the course of four years, Pacific Northwest National Laboratory (PNNL) worked with American Electric Power (AEP), Ohio and Battelle Memorial Institute to design, build, and operate an innovative system to engage residential consumers and their end-use resources in a participatory approach to electric system operations, an incentive-based approach that has the promise of providing greater efficiency under normal operating conditions and greater flexibility to react under situations of system stress. The material contained in this report supplements the findings documented by AEP Ohio in the main body of the gridSMART report. It delves into three main areas: impacts on system operations, impacts on households, and observations about the sensitivity of load to price changes.

A comparison of approximation techniques for variance-based sensitivity analysis of biochemical reaction systems

Directory of Open Access Journals (Sweden)

Goutsias John

2010-05-01

Full Text Available Abstract Background Sensitivity analysis is an indispensable tool for the analysis of complex systems. In a recent paper, we have introduced a thermodynamically consistent variance-based sensitivity analysis approach for studying the robustness and fragility properties of biochemical reaction systems under uncertainty in the standard chemical potentials of the activated complexes of the reactions and the standard chemical potentials of the molecular species. In that approach, key sensitivity indices were estimated by Monte Carlo sampling, which is computationally very demanding and impractical for large biochemical reaction systems. Computationally efficient algorithms are needed to make variance-based sensitivity analysis applicable to realistic cellular networks, modeled by biochemical reaction systems that consist of a large number of reactions and molecular species. Results We present four techniques, derivative approximation (DA, polynomial approximation (PA, Gauss-Hermite integration (GHI, and orthonormal Hermite approximation (OHA, for analytically approximating the variance-based sensitivity indices associated with a biochemical reaction system. By using a well-known model of the mitogen-activated protein kinase signaling cascade as a case study, we numerically compare the approximation quality of these techniques against traditional Monte Carlo sampling. Our results indicate that, although DA is computationally the most attractive technique, special care should be exercised when using it for sensitivity analysis, since it may only be accurate at low levels of uncertainty. On the other hand, PA, GHI, and OHA are computationally more demanding than DA but can work well at high levels of uncertainty. GHI results in a slightly better accuracy than PA, but it is more difficult to implement. OHA produces the most accurate approximation results and can be implemented in a straightforward manner. It turns out that the computational cost of the

Reaction kinetic analysis of reactor surveillance data

Energy Technology Data Exchange (ETDEWEB)

Yoshiie, T., E-mail: yoshiie@rri.kyoto-u.ac.jp [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka-fu 590-0494 (Japan); Kinomura, A. [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka-fu 590-0494 (Japan); Nagai, Y. [The Oarai Center, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan)

2017-02-15

In the reactor pressure vessel surveillance data of a European-type pressurized water reactor (low-Cu steel), it was found that the concentration of matrix defects was very high, and a large number of precipitates existed. In this study, defect structure evolution obtained from surveillance data was simulated by reaction kinetic analysis using 15 rate equations. The saturation of precipitation and the growth of loops were simulated, but it was not possible to explain the increase in DBTT on the basis of the defect structures. The sub-grain boundary segregation of solutes was discussed for the origin of the DBTT increase.

Status of CONRAD, a nuclear reaction analysis tool

International Nuclear Information System (INIS)

Saint Jean, C. de; Habert, B.; Litaize, O.; Noguere, G.; Suteau, C.

2008-01-01

The development of a software tool (CONRAD) was initiated at CEA/Cadarache to give answers to various problems arising in the data analysis of nuclear reactions. This tool is then characterized by the handling of uncertainties from experimental values to covariance matrices for multi-group cross sections. An object oriented design was chosen allowing an easy interface with graphical tool for input/output data and being a natural framework for innovative nuclear models (Fission). The major achieved developments are a data model for describing channels, nuclear reactions, nuclear models and processes with interface to classical data formats, theoretical calculations for the resolved resonance range (Reich-Moore) and unresolved resonance range (Hauser-Feshbach, Gilbert-Cameron,...) with nuclear model parameters adjustment on experimental data sets and a Monte Carlo method based on conditional probabilities developed to calculate properly covariance matrices. The on-going developments deal with the experimental data description (covariance matrices) and the graphical user interface. (authors)

Numerical Analysis Of Hooke Jeeves-Runge Kutta To Determine Reaction Rate Equation In Pyrrole Polymerization

International Nuclear Information System (INIS)

Gunawan, Indra; Sulistyo, Harry; Rochmad

2001-01-01

The numerical analysis of Hooke Jeeves Methods combined with Runge Kutta Methods is used to determine the exact model of reaction rate equation of pyrrole polymerization. Chemical polymerization of pyrrole was conducted with FeCI 3 / pyrrole solution at concentration ratio of 1.62 mole / mole and 2.18 mole / mole with varrying temperature of 28, 40, 50, and 60 o C. FeCl 3 acts as an oxidation agent to form pyrrole cation that will polymerize. The numerical analysis was done to examine the exact model of reaction rate equation which is derived from reaction equation of initiation, propagation, and termination. From its numerical analysis, it is found that the pyrrole polymerization follows third order of pyrrole cation concentration

What Is a Reaction Rate?

Science.gov (United States)

Schmitz, Guy

2005-01-01

The definition of reaction rate is derived and demonstrations are made for the care to be taken while using the term. Reaction rate can be in terms of a reaction property, the extent of reaction and thus it is possible to give a definition applicable in open and closed systems.

Quantitative and Selective Analysis of Feline Growth Related Proteins Using Parallel Reaction Monitoring High Resolution Mass Spectrometry.

Directory of Open Access Journals (Sweden)

Mårten Sundberg

Full Text Available Today immunoassays are widely used in veterinary medicine, but lack of species specific assays often necessitates the use of assays developed for human applications. Mass spectrometry (MS is an attractive alternative due to high specificity and versatility, allowing for species-independent analysis. Targeted MS-based quantification methods are valuable complements to large scale shotgun analysis. A method referred to as parallel reaction monitoring (PRM, implemented on Orbitrap MS, has lately been presented as an excellent alternative to more traditional selected reaction monitoring/multiple reaction monitoring (SRM/MRM methods. The insulin-like growth factor (IGF-system is not well described in the cat but there are indications of important differences between cats and humans. In feline medicine IGF-I is mainly analyzed for diagnosis of growth hormone disorders but also for research, while the other proteins in the IGF-system are not routinely analyzed within clinical practice. Here, a PRM method for quantification of IGF-I, IGF-II, IGF binding protein (BP -3 and IGFBP-5 in feline serum is presented. Selective quantification was supported by the use of a newly launched internal standard named QPrEST™. Homology searches demonstrated the possibility to use this standard of human origin for quantification of the targeted feline proteins. Excellent quantitative sensitivity at the attomol/μL (pM level and selectivity were obtained. As the presented approach is very generic we show that high resolution mass spectrometry in combination with PRM and QPrEST™ internal standards is a versatile tool for protein quantitation across multispecies.

Prediction of Support Reaction Forces of ITA via Response Spectrum Analysis

Energy Technology Data Exchange (ETDEWEB)

Kwak, Jin Sung; Jeong, Joon Ho; Lee, Sang Jin; Oh, Jin Ho; Lee, Jong Min [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The irradiation targets are transferred along pipes between TTS (Target Transfer Station) and ITA (Irradiation Tube Assembly) by hydraulic forces. The ITA corresponds to the vertical guide tube for irradiation targets inside a reactor, and it penetrates the reactor structure. Because the ITA is classified into seismic category II, its structural integrity must be evaluated by the seismic analysis. To approach more realistic problem, the interaction between the ITA and the reactor structure must be considered. However, this paper is focused on the preliminary analysis, and it is simplified that only the response of the ITA caused by earthquake affects the reactor structure. The response of the ITA is predicted by the spectrum response analysis based on the FDRS (Floor Design Response Spectra) of KJRR. Finally, the reaction forces corresponding to the load transfer into the reactor structure are estimated by using ANSYS. In this study, the reaction forces due to the earthquake are estimated by the response spectrum analysis. For the saving computational time and resource required, the FE model with beam element is constructed, and it is confirmed that the accuracy of the solution is acceptable by comparing the results of the solid model.

Partial wave analysis of the 18O(p,α0)15N reaction

International Nuclear Information System (INIS)

Wild, L.W.J.; Spicer, B.M.

1979-01-01

A partial wave analysis of the differential cross sections for the 18 O(p,α 0 ) 15 N reaction has been carried out applying the formalism of Blatt and Biedenharn (1952), made specific for this reaction. The differential cross sections, measured at 200 keV intervals from 6.6 to 10.4 MeV bombarding energy, were subjected to least-squares fitting to this specific analytic expression. Two resonances were given by the analysis, the 19 F states being at 14.71+-0.07 MeV (1/2 - ) and 14.80 + 0.07 MeV (1/2) +

Multidimensional analysis of collective sidewards flow in Au on Au reactions between 100 and 1050 A MeV

International Nuclear Information System (INIS)

Wienold, T.; Fan, Z.G.; Hartnack, C.

1994-11-01

An excitation function of the Au on Au reaction from 100 to 1050 A MeV was measured using the FOPI-facility at GSI Darmstadt. Nuclear charge (Z≤15) and velocity of the product were detected with full azimuthal acceptance at laboratory angles 1 ≤Θ lab ≤30 . For the first time an analysis is presented which combines the azimuthally asymmetric part of the transverse flow (sidewards flow), stopping and the associated collision geometry. In comparison to microscopic transport model calculations we demonstrate the relevance of this method for the extraction of the nuclear equation of state. (orig.)

Thermal analysis experiment for elucidating sodium-water chemical reaction mechanism in steam generator of sodium-cooled fast reactor

International Nuclear Information System (INIS)

Kikuchi, Shin; Kurihara, Akikazu; Ohshima, Hiroyuki

2012-01-01

For the purpose of elucidating the mechanism of the sodium-water surface reaction in a steam generator of sodium-cooled fast reactors, kinetic study of the sodium (Na)-sodium hydroxide (NaOH) reaction has been carried out by using Differential Thermal Analysis (DTA) technique. The parameters, including melting points of Na and NaOH, phase transition temperature of NaOH, Na-NaOH reaction temperature, and decomposition temperature of sodium hydride (NaH) have been identified from DTA curves. Based on the measured reaction temperature, rate constant of sodium monoxide (Na 2 O) generation was obtained. Thermal analysis results indicated that Na 2 O generation at the secondary overall reaction should be considered during the sodium-water reaction. (author)

Thermally multiplexed polymerase chain reaction.

Science.gov (United States)

Phaneuf, Christopher R; Pak, Nikita; Saunders, D Curtis; Holst, Gregory L; Birjiniuk, Joav; Nagpal, Nikita; Culpepper, Stephen; Popler, Emily; Shane, Andi L; Jerris, Robert; Forest, Craig R

2015-07-01

Amplification of multiple unique genetic targets using the polymerase chain reaction (PCR) is commonly required in molecular biology laboratories. Such reactions are typically performed either serially or by multiplex PCR. Serial reactions are time consuming, and multiplex PCR, while powerful and widely used, can be prone to amplification bias, PCR drift, and primer-primer interactions. We present a new thermocycling method, termed thermal multiplexing, in which a single heat source is uniformly distributed and selectively modulated for independent temperature control of an array of PCR reactions. Thermal multiplexing allows amplification of multiple targets simultaneously-each reaction segregated and performed at optimal conditions. We demonstrate the method using a microfluidic system consisting of an infrared laser thermocycler, a polymer microchip featuring 1 μl, oil-encapsulated reactions, and closed-loop pulse-width modulation control. Heat transfer modeling is used to characterize thermal performance limitations of the system. We validate the model and perform two reactions simultaneously with widely varying annealing temperatures (48 °C and 68 °C), demonstrating excellent amplification. In addition, to demonstrate microfluidic infrared PCR using clinical specimens, we successfully amplified and detected both influenza A and B from human nasopharyngeal swabs. Thermal multiplexing is scalable and applicable to challenges such as pathogen detection where patients presenting non-specific symptoms need to be efficiently screened across a viral or bacterial panel.

Dynamical structure analysis of crystalline-state reaction and elucidation of chemical reactivity in crystalline environment

International Nuclear Information System (INIS)

Ohashi, Yuji

2010-01-01

It was found that a chiral alkyl group bonded to the cobalt atom in a cobalt complex crystal was racemized with retention of the single crystal form on exposure to visible light. Such reactions, which are called crystalline-state reactions, have been found in a variety of cobalt complex crystals. The concept of reaction cavity was introduced to explain the reaction rate quantitatively and the chirality of the photo-product. The new diffractometers and detectors were made for rapid data collection. The reaction mechanism was also elucidated using neutron diffraction analysis. The unstable reaction intermediates were analyzed using cryo-trapping method. The excited-state structures were obtained at the equilibrium state between ground and excited states. (author)

PA activity by using nuclear power plant safety demonstration and analysis

International Nuclear Information System (INIS)

Tsuchiya, Mitsuo; Kamimae, Rie

1999-01-01

INS/NUPEC presents one of Public acceptance (PA) methods for nuclear power in Japan, 'PA activity by using Nuclear Power Plant Safety Demonstration and Analysis', by using one of videos which is explained and analyzed accident events (Loss of Coolant Accident). Safety regulations of The National Government are strictly implemented in licensing at each of basic design and detailed design. To support safety regulation activities conducted by the National Government, INS/NLTPEC continuously implement Safety demonstration and analysis. With safety demonstration and analysis, made by assuming some abnormal conditions, what impacts could be produced by the assumed conditions are forecast based on specific design data on a given nuclear power plants. When analysis results compared with relevant decision criteria, the safety of nuclear power plants is confirmed. The decision criteria are designed to help judge if or not safety design of nuclear power plants is properly made. The decision criteria are set in the safety examination guidelines by taking sufficient safety allowance based on the latest technical knowledge obtained from a wide range of tests and safety studies. Safety demonstration and analysis is made by taking the procedure which are summarized in this presentation. In Japan, various PA (Public Acceptance) pamphlets and videos on nuclear energy have been published. But many of them focused on such topics as necessity or importance of nuclear energy, basic principles of nuclear power generation, etc., and a few described safety evaluation particularly of abnormal and accident events in accordance with the regulatory requirements. In this background, INS/NUPEC has been making efforts to prepare PA pamphlets and videos to explain the safety of nuclear power plants, to be simple and concrete enough, using various analytical computations for abnormal and accident events. In results, PA activity of INS/NUPEC is evaluated highly by the people

Generalization of the dispersion relations demonstration; Generalisation de la demonstration des relations de dispersion

Energy Technology Data Exchange (ETDEWEB)

Omnes, Roland [Commissariat a l' energie atomique et aux energies alternatives - CEA (France)

1960-07-01

A modification of the dispersion relations demonstration for two-particle collisions in field theory is indicated. The direct study of the holomorphy domain of the reaction amplitude, without any reference to a particular coordinate system, allows to demonstrate the dispersion relations with fixed pulse transfer for any input and output particle mass. Reprint of a paper published in Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 1203-1205, sitting of 15 February 1960 [French] On indique une modification de la demonstration des relations de dispersion pour les collisions a deux particules en theorie des champs. En etudiant directement le domaine d'holomorphie de l'amplitude de reaction sans se referer a un systeme de coordonnees particulier, on demontre les relations de dispersion a transfert d'impulsion fixe dans le cas ou les masses des particules entrantes et sortantes sont quelconques. Reproduction d'un article publie dans les Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 1203-1205, seance du 15 fevrier 1960.

Reaction time for trimolecular reactions in compartment-based reaction-diffusion models

Science.gov (United States)

Li, Fei; Chen, Minghan; Erban, Radek; Cao, Yang

2018-05-01

Trimolecular reaction models are investigated in the compartment-based (lattice-based) framework for stochastic reaction-diffusion modeling. The formulae for the first collision time and the mean reaction time are derived for the case where three molecules are present in the solution under periodic boundary conditions. For the case of reflecting boundary conditions, similar formulae are obtained using a computer-assisted approach. The accuracy of these formulae is further verified through comparison with numerical results. The presented derivation is based on the first passage time analysis of Montroll [J. Math. Phys. 10, 753 (1969)]. Montroll's results for two-dimensional lattice-based random walks are adapted and applied to compartment-based models of trimolecular reactions, which are studied in one-dimensional or pseudo one-dimensional domains.

Data Analysis for ARRA Early Fuel Cell Market Demonstrations (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Kurtz, J.; Wipke, K.; Sprik, S.; Ramsden, T.

2010-05-01

Presentation about ARRA Early Fuel Cell Market Demonstrations, including an overview of the ARRE Fuel Cell Project, the National Renewable Energy Laboratory's data analysis objectives, deployment composite data products, and planned analyses.

Hydrogen release from irradiated elastomers measured by Nuclear Reaction Analysis

Energy Technology Data Exchange (ETDEWEB)

Jagielski, J., E-mail: jacek.jagielski@itme.edu.pl [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland); Ostaszewska, U. [Institute for Engineering of Polymer Materials & Dyes, Division of Elastomers & Rubber Technology, Harcerska 30, 05-820 Piastow (Poland); Bielinski, D.M. [Technical University of Lodz, Institute of Polymer & Dye Technology, Stefanowskiego 12/16, 90-924 Lodz (Poland); Grambole, D. [Institute of Ion Beam Physics and Materials Research, Helmholtz Zentrum Dresden Rossendorf, PO Box 51 01 19, D-01314 Dresden (Germany); Romaniec, M.; Jozwik, I.; Kozinski, R. [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); Kosinska, A. [National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland)

2016-03-15

Ion irradiation appears as an interesting method of modification of elastomers, especially friction and wear properties. Main structural effect caused by heavy ions is a massive loss of hydrogen from the surface layer leading to its smoothening and shrinking. The paper presents the results of hydrogen release from various elastomers upon irradiation with H{sup +}, He{sup +} and Ar{sup +} studied by using Nuclear Reaction Analysis (NRA) method. The analysis of the experimental data indicates that the hydrogen release is controlled by inelastic collisions between ions and target electrons. The last part of the study was focused on preliminary analysis of mechanical properties of irradiated rubbers.

Metabolic control analysis of biochemical pathways based on a thermokinetic description of reaction rates

DEFF Research Database (Denmark)

Nielsen, Jens Bredal

1997-01-01

Metabolic control analysis is a powerful technique for the evaluation of flux control within biochemical pathways. Its foundation is the elasticity coefficients and the flux control coefficients (FCCs). On the basis of a thermokinetic description of reaction rates it is here shown...... that the elasticity coefficients can be calculated directly from the pool levels of metabolites at steady state. The only requirement is that one thermodynamic parameter be known, namely the reaction affinity at the intercept of the tangent in the inflection point of the curve of reaction rate against reaction...... of the thermokinetic description of reaction rates to include the influence of effecters. Here the reaction rate is written as a linear function of the logarithm of the metabolite concentrations. With this type of rate function it is shown that the approach of Delgado and Liao [Biochem. J. (1992) 282, 919-927] can...

Dichotomous-noise-induced pattern formation in a reaction-diffusion system

Science.gov (United States)

Das, Debojyoti; Ray, Deb Shankar

2013-06-01

We consider a generic reaction-diffusion system in which one of the parameters is subjected to dichotomous noise by controlling the flow of one of the reacting species in a continuous-flow-stirred-tank reactor (CSTR) -membrane reactor. The linear stability analysis in an extended phase space is carried out by invoking Furutzu-Novikov procedure for exponentially correlated multiplicative noise to derive the instability condition in the plane of the noise parameters (correlation time and strength of the noise). We demonstrate that depending on the correlation time an optimal strength of noise governs the self-organization. Our theoretical analysis is corroborated by numerical simulations on pattern formation in a chlorine-dioxide-iodine-malonic acid reaction-diffusion system.

System of gait analysis based on ground reaction force assessment

Directory of Open Access Journals (Sweden)

František Vaverka

2015-12-01

Full Text Available Background: Biomechanical analysis of gait employs various methods used in kinematic and kinetic analysis, EMG, and others. One of the most frequently used methods is kinetic analysis based on the assessment of the ground reaction forces (GRF recorded on two force plates. Objective: The aim of the study was to present a method of gait analysis based on the assessment of the GRF recorded during the stance phase of two steps. Methods: The GRF recorded with a force plate on one leg during stance phase has three components acting in directions: Fx - mediolateral, Fy - anteroposterior, and Fz - vertical. A custom-written MATLAB script was used for gait analysis in this study. This software displays instantaneous force data for both legs as Fx(t, Fy(t and Fz(t curves, automatically determines the extremes of functions and sets the visual markers defining the individual points of interest. Positions of these markers can be easily adjusted by the rater, which may be necessary if the GRF has an atypical pattern. The analysis is fully automated and analyzing one trial takes only 1-2 minutes. Results: The method allows quantification of temporal variables of the extremes of the Fx(t, Fy(t, Fz(t functions, durations of the braking and propulsive phase, duration of the double support phase, the magnitudes of reaction forces in extremes of measured functions, impulses of force, and indices of symmetry. The analysis results in a standardized set of 78 variables (temporal, force, indices of symmetry which can serve as a basis for further research and diagnostics. Conclusions: The resulting set of variable offers a wide choice for selecting a specific group of variables with consideration to a particular research topic. The advantage of this method is the standardization of the GRF analysis, low time requirements allowing rapid analysis of a large number of trials in a short time, and comparability of the variables obtained during different research measurements.

Meta-analysis to obtain a scale of psychological reaction after perinatal loss: focus on miscarriage

Directory of Open Access Journals (Sweden)

Annsofie Adolfsson

2011-03-01

Full Text Available Annsofie Adolfsson1,21School of Life Sciences, University of Skövde, 2Department of Obstetrics and Gynecology, Skaraborg Hospital, Skövde, SwedenAbstract: Pregnancy has different meanings to different women depending upon their circumstances. A number of qualitative studies have described the experience of miscarriage by women who had desired to carry their pregnancy to full term. The aim of this meta-analysis was to identify a scale of psychological reaction to miscarriage. Meta-analysis is a quantitative approach for reviewing articles from scientific journals through statistical analysis of findings from individual studies. In this review, a meta-analytic method was used to identify and analyze psychological reactions in women who have suffered a miscarriage. Different reactions to stress associated with the period following miscarriage were identified. The depression reaction had the highest average, weighted, unbiased estimate of effect (d+ = 0.99 and was frequently associated with the experience of perinatal loss. Psychiatric morbidity was found after miscarriage in 27% of cases by a diagnostic interview ten days after miscarriage. The grief reaction had a medium d+ of 0.56 in the studies included. However, grief after miscarriage differed from other types of grief after perinatal loss because the parents had no focus for their grief. The guilt is greater after miscarriage than after other types of perinatal loss. Measurement of the stress reaction and anxiety reaction seems to be difficult in the included studies, as evidenced by a low d+ (0.17 and 0.16, respectively. It has been recommended that grief after perinatal loss be measured by an adapted instrument called the Perinatal Grief Scale Short Version.Keywords: psychological, perinatal loss, pregnancy, depression 

Thermodynamic analysis of dust sulphation reactions

Energy Technology Data Exchange (ETDEWEB)

Yang Yongxiang; Jokilaakso, A.

1997-12-31

Sulphation reactions of metal oxides with SO{sub 2} and O. or SO{sub 3} play significant roles in sulphation roasting of sulphide and oxide minerals as well as in desulphurisation process of combustion gases. In metallurgical waste-heat boilers for sulphide smelting, the sulphation of the oxidic flue dust in the atmosphere containing sulphur oxides is an unavoidable process, and the sulphation reactions have to be guided in a controlled way in the proper parts of the gas handling equipment. In this report, some thermodynamic analyses were conducted for the oxide sulphation reactions in relation to sulphide smelting processes. The phase stability of Me-S-O systems especially for oxides - sulphates equilibrium was studied under different thermodynamic conditions of gas compositions and temperatures. The sulphate stability was analysed for an example of gas compositions in the copper flash smelter of Outokumpu Harjavalta Metals Oy, in relation to temperature. In the report, most of the information was from literature. Moreover, a number of thermodynamic computations were carried out with the HSC program, and the constructed phase stability diagrams were compared with those from the literature whenever possible. The maximum temperatures for stable sulphates under normal operating conditions of the waste-heat boilers in sulphide smelting processes were obtained. This report will serve as the basis for the kinetic studies of the sulphation reactions and the sulphation reaction modelling in pyrometallurgical processes. (orig.) SULA 2 Programme. 36 refs.

Post mitigation impact risk analysis for asteroid deflection demonstration missions

Science.gov (United States)

Eggl, Siegfried; Hestroffer, Daniel; Thuillot, William; Bancelin, David; Cano, Juan L.; Cichocki, Filippo

2015-08-01

Even though mankind believes to have the capabilities to avert potentially disastrous asteroid impacts, only the realization of mitigation demonstration missions can validate this claim. Such a deflection demonstration attempt has to be cost effective, easy to validate, and safe in the sense that harmless asteroids must not be turned into potentially hazardous objects. Uncertainties in an asteroid's orbital and physical parameters as well as those additionally introduced during a mitigation attempt necessitate an in depth analysis of deflection mission designs in order to dispel planetary safety concerns. We present a post mitigation impact risk analysis of a list of potential kinetic impactor based deflection demonstration missions proposed in the framework of the NEOShield project. Our results confirm that mitigation induced uncertainties have a significant influence on the deflection outcome. Those cannot be neglected in post deflection impact risk studies. We show, furthermore, that deflection missions have to be assessed on an individual basis in order to ensure that asteroids are not inadvertently transported closer to the Earth at a later date. Finally, we present viable targets and mission designs for a kinetic impactor test to be launched between the years 2025 and 2032.

Theoretical analysis of thermal molten metal-water reactions

International Nuclear Information System (INIS)

Schwalbe, W.

1982-01-01

In experiments with greater masses (kg-scale) two extreme cases had been oberved during the course of reaction when hot melt reacted with a vaporizable cooler liquid. Relatively mild hot interactions with slow pressure build-up and small pressure peak in the reaction volume often occurred but there were also some very violent reactions (steam explosions) where a remarkable portion of thermal energy had been transformed into mechanical energy with high pressure peaks. For the two types of reactions overall models for water as a coolant are developed here. Based on calculations and on comparisons with corresponding experiments it is shown that a relatively mild course of reaction can be explained by a fragmentation of the melt under following violent evaporation of the cooling medium. Pressures only with small reaction volumes up to the MPa range can be found in these reactions. The calculations, for example of Bird and Millington, showed a pressure maximum of 1 MPa after 170 ms of the start of the reaction; this agrees very well with the result of the experiment of 1.08 MPa. (orig./GL) [de

Hydroamination reactions of alkynes with ortho-substituted anilines in ball mills: synthesis of benzannulated N-heterocycles by a cascade reaction.

Science.gov (United States)

Weiße, Maik; Zille, Markus; Jacob, Katharina; Schmidt, Robert; Stolle, Achim

2015-04-20

It was demonstrated that ortho-substituted anilines are prone to undergo hydroamination reactions with diethyl acetylenedicarboxylate in a planetary ball mill. A sequential coupling of the intermolecular hydroamination reaction with intramolecular ring closure was utilized for the syntheses of benzooxazines, quinoxalines, and benzothiazines from readily available building blocks, that is, electrophilic alkynes and anilines with OH, NH, or SH groups in the ortho position. For the heterocycle formation, it was shown that several stress conditions were able to initiate the reaction in the solid state. Processing in a ball mill seemed to be advantageous over comminution with mortar and pestle with respect to process control. In the latter case, significant postreaction modification occurred during solid-state analysis. Cryogenic milling proved to have an adverse effect on the molecular transformation of the reagents. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Applications of the photo-nuclear reaction data for activation analysis

International Nuclear Information System (INIS)

Odsuren, M.; Khuukhenkhuu, G.; Turbold, A.; Davaa, S.; Baatarkhuu, D.

2015-01-01

In the relative method of activation analysis by continuum wide spectrum gamma-rays the same isotope is usually used for standard reference element and sample material in connection with different dependence of the reaction cross sections on the irradiation beam energy. But, in practice suitable isotopes for reference element are not always available. So, in this paper, we suggest a new method for photo-activation analysis in which is used the correction factor. This factor takes into account the difference in the photo-nuclear reaction cross section dependence on the gamma-ray energy for standard reference isotope and sample elements. The correction factor is determined by three methods of experimental, theoretical and TALYS evaluation. Pure metal foils of Au, Cu and Mo were irradiated by bremsstrahlung gamma-rays on the electron cyclic accelerator Microtron MT-22 at the Nuclear Research Center, National University of Mongolia. Gamma spectra of the activated metal foils were measured by HP-Ge detector to obtain element contents in the samples. It was shown that experimental results with correction factors are satisfactorily in agreement with real values of the element contents in the samples

Software news and update PyFrag - Streamlining your reaction path analysis

NARCIS (Netherlands)

van Zeist, W.-J.; Fonseca Guerra, C.; Bickelhaupt, F.M.

2008-01-01

The PyFrag program (released as PyFrag2007.01) is a "wrap-around" for the Amsterdam Density Functional (ADF) package and facilitates the extension of the fragment analysis method implemented in ADF along an entire potential energy surface. The purpose is to make analyses of reaction paths and other

Reaction Decoder Tool (RDT): extracting features from chemical reactions.

Science.gov (United States)

Rahman, Syed Asad; Torrance, Gilliean; Baldacci, Lorenzo; Martínez Cuesta, Sergio; Fenninger, Franz; Gopal, Nimish; Choudhary, Saket; May, John W; Holliday, Gemma L; Steinbeck, Christoph; Thornton, Janet M

2016-07-01

Extracting chemical features like Atom-Atom Mapping (AAM), Bond Changes (BCs) and Reaction Centres from biochemical reactions helps us understand the chemical composition of enzymatic reactions. Reaction Decoder is a robust command line tool, which performs this task with high accuracy. It supports standard chemical input/output exchange formats i.e. RXN/SMILES, computes AAM, highlights BCs and creates images of the mapped reaction. This aids in the analysis of metabolic pathways and the ability to perform comparative studies of chemical reactions based on these features. This software is implemented in Java, supported on Windows, Linux and Mac OSX, and freely available at https://github.com/asad/ReactionDecoder : asad@ebi.ac.uk or s9asad@gmail.com. © The Author 2016. Published by Oxford University Press.

Demonstration uncertainty/sensitivity analysis using the health and economic consequence model CRAC2

International Nuclear Information System (INIS)

Alpert, D.J.; Iman, R.L.; Johnson, J.D.; Helton, J.C.

1985-01-01

This paper summarizes a demonstration uncertainty/sensitivity analysis performed on the reactor accident consequence model CRAC2. The study was performed with uncertainty/sensitivity analysis techniques compiled as part of the MELCOR program. The principal objectives of the study were: 1) to demonstrate the use of the uncertainty/sensitivity analysis techniques on a health and economic consequence model, 2) to test the computer models which implement the techniques, 3) to identify possible difficulties in performing such an analysis, and 4) to explore alternative means of analyzing, displaying, and describing the results. Demonstration of the applicability of the techniques was the motivation for performing this study; thus, the results should not be taken as a definitive uncertainty analysis of health and economic consequences. Nevertheless, significant insights on health and economic consequence analysis can be drawn from the results of this type of study. Latin hypercube sampling (LHS), a modified Monte Carlo technique, was used in this study. LHS generates a multivariate input structure in which all the variables of interest are varied simultaneously and desired correlations between variables are preserved. LHS has been shown to produce estimates of output distribution functions that are comparable with results of larger random samples

Lab-on-a-chip based total-phosphorus analysis device utilizing a photocatalytic reaction

Science.gov (United States)

Jung, Dong Geon; Jung, Daewoong; Kong, Seong Ho

2018-02-01

A lab-on-a-chip (LOC) device for total phosphorus (TP) analysis was fabricated for water quality monitoring. Many commercially available TP analysis systems used to estimate water quality have good sensitivity and accuracy. However, these systems also have many disadvantages such as bulky size, complex pretreatment processes, and high cost, which limit their application. In particular, conventional TP analysis systems require an indispensable pretreatment step, in which the fluidic analyte is heated to 120 °C for 30 min to release the dissolved phosphate, because many phosphates are soluble in water at a standard temperature and pressure. In addition, this pretreatment process requires elevated pressures of up to 1.1 kg cm-2 in order to prevent the evaporation of the heated analyte. Because of these limiting conditions required by the pretreatment processes used in conventional systems, it is difficult to miniaturize TP analysis systems. In this study, we employed a photocatalytic reaction in the pretreatment process. The reaction was carried out by illuminating a photocatalytic titanium dioxide (TiO2) surface formed in a microfluidic channel with ultraviolet (UV) light. This pretreatment process does not require elevated temperatures and pressures. By applying this simplified, photocatalytic-reaction-based pretreatment process to a TP analysis system, greater degrees of freedom are conferred to the design and fabrication of LOC devices for TP monitoring. The fabricated LOC device presented in this paper was characterized by measuring the TP concentration of an unknown sample, and comparing the results with those measured by a conventional TP analysis system. The TP concentrations of the unknown sample measured by the proposed LOC device and the conventional TP analysis system were 0.018 mgP/25 mL and 0.019 mgP/25 mL, respectively. The experimental results revealed that the proposed LOC device had a performance comparable to the conventional bulky TP analysis

Reaction energetics on long-range corrected density functional theory: Diels-Alder reactions.

Science.gov (United States)

Singh, Raman K; Tsuneda, Takao

2013-02-15

The possibility of quantitative reaction analysis on the orbital energies of long-range corrected density functional theory (LC-DFT) is presented. First, we calculated the Diels-Alder reaction enthalpies that have been poorly given by conventional functionals including B3LYP functional. As a result, it is found that the long-range correction drastically improves the reaction enthalpies. The barrier height energies were also computed for these reactions. Consequently, we found that dispersion correlation correction is also crucial to give accurate barrier height energies. It is, therefore, concluded that both long-range exchange interactions and dispersion correlations are essentially required in conventional functionals to investigate Diels-Alder reactions quantitatively. After confirming that LC-DFT accurately reproduces the orbital energies of the reactant and product molecules of the Diels-Alder reactions, the global hardness responses, the halves of highest occupied molecular orbital (HOMO)-lowest unoccupied molecular orbital (LUMO) energy gaps, along the intrinsic reaction coordinates of two Diels-Alder reactions were computed. We noticed that LC-DFT results satisfy the maximum hardness rule for overall reaction paths while conventional functionals violate this rule on the reaction pathways. Furthermore, our results also show that the HOMO-LUMO gap variations are close to the reaction enthalpies for these Diels-Alder reactions. Based on these results, we foresee quantitative reaction analysis on the orbital energies. Copyright © 2012 Wiley Periodicals, Inc.

ANALYSIS OF A POSSIBLE REDUCTION IN ENERGY CONSUMPTION IN WATER ELECTROLYSIS REACTION

Directory of Open Access Journals (Sweden)

Aurel George POPESCU

2013-05-01

Full Text Available It was experimentally observed that the electrolysis reaction continues a short period of time - time torelax c - after the cell power supply is interrupted. This paper presents an analysis of transient phenomenaoccurring and pr opose technical solutions

Analysis of the 7Be (P, γ) 8B reaction at extremely low energies within the modified two-body potential approach

International Nuclear Information System (INIS)

Sanetullaev, A.; Igamov, S.B.; Yarmukhamedov, R.

2004-01-01

Full text: Obtaining the extremely low energy cross sections for the reaction 7 Be(p,γ ) 8 B is of great interest for a reliable estimation of the rate of this reaction, which is crucial for an accurate determination of the solar neutrino flux. At present, in current literature, there is a rather wide spread in estimation of this rate (see, for instance, Ref. [1] and references therein). In this work, the modified two-body potential approach for analysis of the astrophysical S- factor S(E) for the peripheral direct radiative capture 7 Be(p,γ ) 8 B reaction of astrophysical interest is applied, in which the additional conditions of verification of the peripheral character of the reaction under consideration are formulated. The method involves the information on the asymptotic normalization coefficient (ANC) for the virtual decay 8 B → 7 Be+p and allows one to exclude the model dependence of the calculated direct astrophysical S-factor S(E) on the geometric parameters (radius r 0 and diffuseness a) of the adopted Woods-Saxon potential, which is usually used for calculations both for the two-body ( 7 Be+p)-bound state and for the 7 Be p -scattering state. The rather precise experimental astrophysical S-factor, S exp (E), in the energy range 100 7 Be(p,γ ) 8 B reaction, measured recently by the authors of Ref. [1] is used for the analysis. It is demonstrated that at extremely low energies this reaction is strongly peripheral and the measured S exp (E) can be used as an independent source of getting the information about the ANC. The new information about values of the ANC is obtained with an estimation of the weighted mean errors for them, which involves both the experimental errors of the S exp (E), and uncertainty of the method not exceeding 4%. The extracted value of the ANC is equal to C 2 =C 2 1/2 +C 2 3/2 =5.68± 0.15 fm -1 , where the indices show the value total angular momentum of the proton in the (p+ 7 Be)-bound state of 8 B. It was also demonstrated

Assumption-free analysis of quantitative real-time polymerase chain reaction (PCR) data

NARCIS (Netherlands)

Ramakers, Christian; Ruijter, Jan M.; Deprez, Ronald H. Lekanne; Moorman, Antoon F. M.

2003-01-01

Quantification of mRNAs using real-time polymerase chain reaction (PCR) by monitoring the product formation with the fluorescent dye SYBR Green I is being extensively used in neurosciences, developmental biology, and medical diagnostics. Most PCR data analysis procedures assume that the PCR

Analysis of the potential geochemical reactions in the Enceladus' hydrothermal environment

Science.gov (United States)

Ramirez-Cabañas, A. K.; Flandes, A.

2017-12-01

Enceladus is the sixth largest moon of Saturn and differs from its other moons, because of its cryovolcanic geysers that emanate from its south pole. The instruments of the Cassini spacecraft reveal different compounds in the gases and the dust of the geysers, such as salts (sodium chloride, sodium bicarbonate and/or sodium carbonate), as well as silica traces (Postberg et al., 2008, 2009) that could be the result of a hydrothermal environment (Hsu et al., 2014, Sekine et al., 2014). By means of a thermodynamic analysis, we propose and evaluate potential geochemical reactions that could happen from the interaction between the nucleus surface and the inner ocean of Enceladus. These reactions may well lead to the origin of the compounds found in the geysers. From this analysis, we propose that, at least, two minerals must be present in the condritic nucleus of Enceladus: olivines (fayalite and fosterite) and feldspar (orthoclase and albite). Subsequently, taking as reference the hydrothermal processes that take place on Earth, we propose the different stages of a potential hydrothermal scenario for Enceladus.

A Systematic Approach for the Design and Analysis of Reaction-Separation Systems with Recycle

DEFF Research Database (Denmark)

Gani, Rafiqul; Jimenez, Edgar Ramirez

2004-01-01

This paper presents a methodology for a systematic model-based analysis and the results obtained from it for an integrated design and analysis of reaction-separation systems with recycle. The methodology (systematic approach) consists of three stages where stage 1 identifies the limiting values...

Demonstration Analysis of Relationship Between R&D Investment and GDP

Institute of Scientific and Technical Information of China (English)

HAN Bo-tang; LIU Bai-shan; CHEN Keng

2005-01-01

To reveal the quantitative relationship between research and development (R&D) investment and gross domestic product (GDP) in China, we have demonstrated and analyzed the relationship between R&D investment and science and technology (S&T) progress, and based on a mount of S&T statistical data, have proceeded demonstration research of the relationship between R&D investment and GDP in China with Solow and vector auto regression (VAR) models. Cubic curve fitting and cross-correlation analysis of them with SPSS have shown that there is a strong synchronic relationship between R&D investment and GDP.

Analysis of the effects of reaction parameters upon the molecular weight of an aromatic poly(hydrazide) through experimental design

International Nuclear Information System (INIS)

Gomes, Dominique; Pinto, Jose Carlos; Borges, Cristiano P.; Nunes, Suzana P.

2001-01-01

Samples of an aromatic poly(hydrazide) were synthesized through low temperature solution polycondensation reactions. Monomers were characterized by nuclear magnetic resonance (NMR) and thermal analysis. The polymer material was characterized by intrinsic viscosity measurements and by NMR. The thermal behavior of the polymer samples was studied by thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The effect of various factors that influence the course of the polymerization reaction, such as concentration of monomer and electrolyte (LiCl) in the reaction medium, purity of the monomers, reaction temperature and reaction time, were investigated. Reaction conditions were then optimized in order to allow the preparation of high molecular weight polymer resins. Values of intrinsic viscosity obtained for the poly(hydrazide) in N-methyl-2-pyrrolidone were as high as 1.51 dL/g. (author)

Transfusion reactions in pediatric compared with adult patients: a look at rate, reaction type, and associated products.

Science.gov (United States)

Oakley, Fredrick D; Woods, Marcella; Arnold, Shanna; Young, Pampee P

2015-03-01

The majority of reports on transfusion reactions address adult patients. Less is known about the types, incidence, and other clinical details of transfusion reactions in pediatric populations. Furthermore, to our knowledge, there have been no previous reports directly comparing these aspects between adults and pediatric patient populations to assess if there are differences. Between the period of January 1, 2011, and February 1, 2013, all reported adult and pediatric transfusion reactions at Vanderbilt University Medical Center (VUMC) were evaluated by transfusion medicine clinical service. The information was subsequently shared with the hemovigilance database. Data provided to hemovigilance included age, sex, blood product associated with the reaction, severity of the reaction, and the type of transfusion reactions. These were collated with hospital and blood bank information system-acquired data on overall admission and product transfusion. A total of 133,671 transfusions were performed at VUMC during the study period including 20,179 platelet (PLT) transfusions, 31,605 plasma transfusions, 79,933 red blood cell (RBC) transfusions, and 2154 cryoprecipitate transfusions. Over the same period, 108 pediatric and 277 adult transfusion reactions were recorded. This corresponds to an incidence of 6.2 reactions per 1000 transfusions within the pediatric (age reactions per 1000 transfusions within the adult population. In both adult and pediatric populations, transfusion reactions were most commonly associated with PLT, followed by RBC, and then plasma transfusions. Within the pediatric population, subset analysis identified multiple differences when compared to the adult population, including an increased incidence of allergic transfusion reactions (2.7/1000 vs. 1.1/1000, p reactions (1.9/1000 vs. 0.47/1000, p reactions (0.29/1000 vs. 0.078/1000, p reaction incidence was the same between sexes in adults, in pediatric patients, reactions were more common in male

Gamma ray tracking with the AGATA demonstrator. A novel approach for in-beam spectroscopy

International Nuclear Information System (INIS)

Birkenbach, Benedikt

2014-01-01

The Advanced GAmma Tracking Array (AGATA) employs the novel method of γ-ray tracking (GRT), where all locations of energy depositions within the Ge crystal detector volume are used by computer algorithms to reconstruct the various simultaneous interactions of the measured radiation. The interaction positions are determined by Pulse Shape Analysis (PSA) algorithms that compare the measured and digitized signals with the information of a signal database comprising position dependent calculated sets of detector signals. The result of a detailed comparison between measured and calculated signals yields the position of each interaction point. The GRT algorithms rely on this precise position of the deposited energy as an input to reconstruct the initial γ-rays from the full sequence of the different interactions in the detector. Within this thesis a computer program library was developed, providing software routines to calculate the position dependent detector signals of the highly segmented HPGe detectors. The currently used signal databases of all AGATA detectors were generated by this software package and computer library. Part of the computing is based on individual detector properties which were deduced from detailed characterisation measurements. Details of the library, the used routines and the needed characteristics of the detector system are described, this includes a precise measurement of the crystal axis orientation of the AGATA HPGe crystals. The second part of this thesis is dealing with the analysis of one of the first in-beam experiments performed with the AGATA demonstrator setup at the LNL in Italy. The experiment aimed for a spectroscopic investigation of neutron rich actinides from Thorium to Plutonium produced after multi-nucleon transfer reactions. For this purpose a 136 Xe beam with an energy of 1 GeV bombarded onto a 238 U target. The fast beam like particles after the transfer reactions were identified by the magnetic spectrometer PRISMA. The �

Group Analysis of Free Convection Flow of a Magnetic Nanofluid with Chemical Reaction

Directory of Open Access Journals (Sweden)

Md. Jashim Uddin

2015-01-01

Full Text Available A theoretical study of two-dimensional magnetohydrodynamics viscous incompressible free convective boundary layer flow of an electrically conducting, chemically reacting nanofluid from a convectively heated permeable vertical surface is presented. Scaling group of transformations is used in the governing equations and the boundary conditions to determine absolute invariants. A third-order ordinary differential equation which corresponds to momentum conservation and two second-order ordinary differential equations which correspond to energy and nanoparticle volume fraction (species conservation are derived. Our (group analysis indicates that, for the similarity solution, the convective heat transfer coefficient and mass transfer velocity are proportional to x-1/4 whilst the reaction rate is proportional to x-1/2, where x is the axial distance from the leading edge of the plate. The effects of the relevant controlling parameters on the dimensionless velocity, temperature, and nanoparticle volume fraction are examined. The accuracy of the technique we have used was tested by performing comparisons with the results of published work and the results were found to be in good agreement. The present computations indicate that the flow is accelerated and temperature enhanced whereas nanoparticle volume fractions are decreased with increasing order of chemical reaction. Furthermore the flow is strongly decelerated, whereas the nanoparticle volume fraction and temperature are enhanced with increasing magnetic field parameter. Increasing convection-conduction parameter increases velocity and temperatures but has a weak influence on nanoparticle volume fraction distribution. The present study demonstrates the thermal enhancement achieved with nanofluids and also magnetic fields and is of relevance to nanomaterials processing.

Bifurcation Analysis of Gene Propagation Model Governed by Reaction-Diffusion Equations

Directory of Open Access Journals (Sweden)

Guichen Lu

2016-01-01

Full Text Available We present a theoretical analysis of the attractor bifurcation for gene propagation model governed by reaction-diffusion equations. We investigate the dynamical transition problems of the model under the homogeneous boundary conditions. By using the dynamical transition theory, we give a complete characterization of the bifurcated objects in terms of the biological parameters of the problem.

Widely applicable MATLAB routines for automated analysis of saccadic reaction times.

Science.gov (United States)

Leppänen, Jukka M; Forssman, Linda; Kaatiala, Jussi; Yrttiaho, Santeri; Wass, Sam

2015-06-01

Saccadic reaction time (SRT) is a widely used dependent variable in eye-tracking studies of human cognition and its disorders. SRTs are also frequently measured in studies with special populations, such as infants and young children, who are limited in their ability to follow verbal instructions and remain in a stable position over time. In this article, we describe a library of MATLAB routines (Mathworks, Natick, MA) that are designed to (1) enable completely automated implementation of SRT analysis for multiple data sets and (2) cope with the unique challenges of analyzing SRTs from eye-tracking data collected from poorly cooperating participants. The library includes preprocessing and SRT analysis routines. The preprocessing routines (i.e., moving median filter and interpolation) are designed to remove technical artifacts and missing samples from raw eye-tracking data. The SRTs are detected by a simple algorithm that identifies the last point of gaze in the area of interest, but, critically, the extracted SRTs are further subjected to a number of postanalysis verification checks to exclude values contaminated by artifacts. Example analyses of data from 5- to 11-month-old infants demonstrated that SRTs extracted with the proposed routines were in high agreement with SRTs obtained manually from video records, robust against potential sources of artifact, and exhibited moderate to high test-retest stability. We propose that the present library has wide utility in standardizing and automating SRT-based cognitive testing in various populations. The MATLAB routines are open source and can be downloaded from http://www.uta.fi/med/icl/methods.html .

Interfacial reactions in intermetallic matrix composites

International Nuclear Information System (INIS)

Cantrell, L.B.; Clevenger, E.M.; Perepezko, J.H.

1993-01-01

The thermal stability of advanced composites is dominated by the behavior of internal interfaces. Analysis of these internal interfaces often involves consideration of at least ternary order phase equilibria. Limited thermodynamic data exists for ternary and higher order systems. However, a combined approach based upon the use of binary data to estimate ternary phase equilibria and experimentally determined reaction pathways is effective in the analysis of interface reactions in composite systems. In blended powder samples, thermal analysis was used to find possible reaction temperatures, while X-ray analysis, EDS, and EPMA of diffusion couples were used to assess interdiffusion reaction pathways. The approach is illustrated by compatibility studies between TiAl and TiSi 2 at 1,100 C, and in-situ reactions between B 4 C and TiAl at 1300 C where multiple reaction sequences have been analyzed to provide guidance for the design of in-situ reaction processing of composites

Mining chemical reactions using neighborhood behavior and condensed graphs of reactions approaches.

Science.gov (United States)

de Luca, Aurélie; Horvath, Dragos; Marcou, Gilles; Solov'ev, Vitaly; Varnek, Alexandre

2012-09-24

This work addresses the problem of similarity search and classification of chemical reactions using Neighborhood Behavior (NB) and Condensed Graphs of Reaction (CGR) approaches. The CGR formalism represents chemical reactions as a classical molecular graph with dynamic bonds, enabling descriptor calculations on this graph. Different types of the ISIDA fragment descriptors generated for CGRs in combination with two metrics--Tanimoto and Euclidean--were considered as chemical spaces, to serve for reaction dissimilarity scoring. The NB method has been used to select an optimal combination of descriptors which distinguish different types of chemical reactions in a database containing 8544 reactions of 9 classes. Relevance of NB analysis has been validated in generic (multiclass) similarity search and in clustering with Self-Organizing Maps (SOM). NB-compliant sets of descriptors were shown to display enhanced mapping propensities, allowing the construction of better Self-Organizing Maps and similarity searches (NB and classical similarity search criteria--AUC ROC--correlate at a level of 0.7). The analysis of the SOM clusters proved chemically meaningful CGR substructures representing specific reaction signatures.

Organocatalytic aza-Michael/retro-aza-Michael reaction: pronounced chirality amplification in aza-Michael reaction and racemization via retro-aza-Michael reaction.

Science.gov (United States)

Cai, Yong-Feng; Li, Li; Luo, Meng-Xian; Yang, Ke-Fang; Lai, Guo-Qiao; Jiang, Jian-Xiong; Xu, Li-Wen

2011-05-01

A detailed experimental investigation of an aza-Michael reaction of aniline and chalcone is presented. A series of Cinchona alkaloid-derived organocatalysts with different functional groups were prepared and used in the aza-Michael and retro-aza-Michael reaction. There was an interesting finding that a complete reversal of stereoselectivity when a benzoyl group was introduced to the cinchonine and cinchonidine. The chirality amplification vs. time proceeds in the quinine-derived organocatalyst containing silicon-based bulky group, QN-TBS, -catalyzed aza-Michael reaction under solvent-free conditions. In addition, we have demonstrated for the first time that racemization was occurred in suitable solvents under mild conditions due to retro-aza-Michael reaction of the Michael adduct of aniline with chalcone. These indicate the equilibrium of retro-aza-Michael reaction and aza-Michael reaction produce the happening of chirality amplification in aza-Michael reaction and racemization via retro-aza-Michael reaction under different conditions, which would be beneficial to the development of novel chiral catalysts for the aza-Michael reactions. Copyright © 2011 Wiley-Liss, Inc.

Thermogravimetric analysis and kinetic study of bamboo waste treated by Echinodontium taxodii using a modified three-parallel-reactions model.

Science.gov (United States)

Yu, Hongbo; Liu, Fang; Ke, Ming; Zhang, Xiaoyu

2015-06-01

In this study, the effect of pretreatment with Echinodontium taxodii on thermal decomposition characteristics and kinetics of bamboo wastes was investigated by thermogravimetric analysis. The results showed fungal pretreatment can enhance the thermal degradation of bamboo. The negative effect of extractives in bamboo on the thermal decomposition can be decreased by the pretreatment. A modified three-parallel-reactions model based on isolated lignin was firstly proposed to study pyrolysis kinetics of bamboo lignocellulose. Kinetic analysis showed that with increasing pretreatment time fungal delignification was enhanced to transform the lignin component with high activation energy into that with low activation energy and raise the cellulose content in bamboo, making the thermal decomposition easier. These results demonstrated fungal pretreatment provided a potential way to improve thermal conversion efficiency of bamboo. Copyright © 2015 Elsevier Ltd. All rights reserved.

Steady-state isotopic transient kinetic analysis investigation of CO-O2 and CO-NO reactions over a commercial automotive catalyst

International Nuclear Information System (INIS)

Oukaci, R.; Blackmond, D.G.; Goodwin, J.G. Jr.; Gallaher, G.R.

1992-01-01

In this paper, steady-state isotopic transient kinetic analysis (SSITKA) is used to study two model reactions, CO oxidation and CO-NO reactions, on a typical formulation of a three-way auto-catalyst. Under steady-state conditions, abrupt switches in the isotopic composition of CO ( 12 C 16 O/ 13 C 18 O) were carried out to produce isotopic transients in both labeled reactants and products. Along with the determination of the average surface lifetimes and concentrations of reaction intermediates, an analysis of the transient responses along the carbon reaction pathway indicated that the distribution of active sites for the formation of CO 2 was bimodal for both reactions. Furthermore, relatively few surface sites contributed to the overall reaction rate

Compositional analysis of silicon nitride films on Si and GaAs by backscattering spectrometry and nuclear resonance reaction analysis

International Nuclear Information System (INIS)

Kumar, Sanjiv; Raju, V.S.

2004-01-01

This paper describes the application of proton and α-backscattering spectrometry for the determination of atomic ratio of Si to N in 1100-5000 A silicon nitride films on Si and GaAs. The conventional α-Rutherford backscattering spectrometry is suitable for the analysis of films on Si; it is rather inadequate for films on GaAs due to higher background from the substrate. It is shown that these films can be analysed by 14 N(α,α) 14 N scattering with 3.5 MeV α-particles. Proton elastic scattering with enhanced cross sections for 28 Si(p,p) 28 Si and 14 N(p,p) 14 N scatterings, is also suitable for analysing films on GaAs. However, the analysis of films on Si by this technique is difficult due to interferences between the signals of Si from the film and the substrate. In addition, the hydrogen content in films is determined by 1 H( 19 F,αγ) 16 O nuclear reaction analysis using the resonance at 6.4 MeV. The combination of backscattering spectrometry with nuclear reaction analysis provides compositional analysis of ternary Si 1-(x+y) N x H y films

Localized temperature and chemical reaction control in nanoscale space by nanowire array.

Science.gov (United States)

Jin, C Yan; Li, Zhiyong; Williams, R Stanley; Lee, K-Cheol; Park, Inkyu

2011-11-09

We introduce a novel method for chemical reaction control with nanoscale spatial resolution based on localized heating by using a well-aligned nanowire array. Numerical and experimental analysis shows that each individual nanowire could be selectively and rapidly Joule heated for local and ultrafast temperature modulation in nanoscale space (e.g., maximum temperature gradient 2.2 K/nm at the nanowire edge; heating/cooling time chemical reactions such as polymer decomposition/cross-linking and direct and localized hydrothermal synthesis of metal oxide nanowires were demonstrated.

Methyl Salicylate: A Reactive Chemical Warfare Agent Surrogate to Detect Reaction with Hypochlorite (POSTPRINT)

Science.gov (United States)

2011-05-01

presumably due to saponification (Figure 2) followed by a slower decarbox- ylation step to produce detectable amounts of 2-chloro-, 4-chloro- and 2,4...reaction of MeS with hypochlorite demonstrating the effect of a cosolvent on the rate of reaction. Figure 2. Proposed mechanism for EAS, saponification , and...Quantitative analysis of the products is complicated by the competing process of saponification of the esters to chlorophe- nols, and by possible surface

Sedation for pediatric radiological procedures: analysis of potential causes of sedation failure and paradoxical reactions

International Nuclear Information System (INIS)

Karian, V.E.; Burrows, P.E.; Connor, L.; Zurakowski, D.; Mason, K.P.

1999-01-01

Background. Sedation for diagnostic imaging and interventional radiologic procedures in pediatrics has greatly increased over the past decade. With appropriate patient selection and monitoring, serious adverse effects are infrequent, but failure to sedate and paradoxical reactions do occur. Objective. The purpose of this study was to determine, among patients undergoing sedation for radiologic procedures, the incidence of sedation failure and paradoxical reaction to pentobarbital and to identify potentially correctable causes. Materials and methods. Records of 1665 patients who were sedated in the radiology department from 1 November 1997 to 1 July 1998 were reviewed. Patients failing sedation or experiencing paradoxical reaction were compared with respect to sex, age group, diagnosis, scan type, time of day, NPO status, use of IV contrast and type of sedation agent using the Fisher exact test, Pearson chi-square, analysis of variance (ANOVA), the Student t-test, and logistic regression. Results. Data analysis revealed a sedation failure rate of 1 % and paradoxical reaction rate of 1.2 %. Stepwise multiple logistic regression revealed that the only significant independent multivariate predictor of failure was the need for the administration of a combination of pentobarbital, fentanyl, and midazolam IV. Conclusion. The low rate of sedation failure and paradoxical reactions to pentobarbital was near optimal and probably cannot be improved with the currently available sedatives. (orig.)

Sedation for pediatric radiological procedures: analysis of potential causes of sedation failure and paradoxical reactions

Energy Technology Data Exchange (ETDEWEB)

Karian, V.E.; Burrows, P.E.; Connor, L. [Dept. of Radiology, Children' s Hospital, Boston, MA (United States); Zurakowski, D. [Dept. of Biostatistics, Children' s Hospital, Boston, MA (United States); Mason, K.P. [Dept. of Anesthesiology, Children' s Hospital, Boston, MA (United States)

1999-11-01

Background. Sedation for diagnostic imaging and interventional radiologic procedures in pediatrics has greatly increased over the past decade. With appropriate patient selection and monitoring, serious adverse effects are infrequent, but failure to sedate and paradoxical reactions do occur. Objective. The purpose of this study was to determine, among patients undergoing sedation for radiologic procedures, the incidence of sedation failure and paradoxical reaction to pentobarbital and to identify potentially correctable causes. Materials and methods. Records of 1665 patients who were sedated in the radiology department from 1 November 1997 to 1 July 1998 were reviewed. Patients failing sedation or experiencing paradoxical reaction were compared with respect to sex, age group, diagnosis, scan type, time of day, NPO status, use of IV contrast and type of sedation agent using the Fisher exact test, Pearson chi-square, analysis of variance (ANOVA), the Student t-test, and logistic regression. Results. Data analysis revealed a sedation failure rate of 1 % and paradoxical reaction rate of 1.2 %. Stepwise multiple logistic regression revealed that the only significant independent multivariate predictor of failure was the need for the administration of a combination of pentobarbital, fentanyl, and midazolam IV. Conclusion. The low rate of sedation failure and paradoxical reactions to pentobarbital was near optimal and probably cannot be improved with the currently available sedatives. (orig.)

13C(α,n)16O reaction as the knock-out exchange process

International Nuclear Information System (INIS)

Kim, G.; Khajdarov, R.R.; Zaparov, Eh.A.

2000-01-01

S-factor for the 13 C(α,n) 16 O reaction is studied. In the framework of the simple phenomenological model this reaction is analysed as neutron knocked-out by α-particle exchange process. The analysis demonstrates the importance of taking into account 2p-state in 13 C. The 13 C(α,n) 16 O cross section is considered both as the knock-out exchange process and as it's combination with process through a compound nucleus. It was shown that for E α s value extrapolated to low energies is found to be noticeably larger that of R-matrix analysis. Different ways of improving the proposed model are discussed. (author)

Molecular-dynamics analysis of mobile helium cluster reactions near surfaces of plasma-exposed tungsten

Energy Technology Data Exchange (ETDEWEB)

Hu, Lin; Maroudas, Dimitrios, E-mail: maroudas@ecs.umass.edu [Department of Chemical Engineering, University of Massachusetts, Amherst, Massachusetts 01003-9303 (United States); Hammond, Karl D. [Department of Chemical Engineering, University of Missouri, Columbia, Missouri 65211 (United States); Wirth, Brian D. [Department of Nuclear Engineering, University of Tennessee, Knoxville, Tennessee 37996 (United States)

2015-10-28

We report the results of a systematic atomic-scale analysis of the reactions of small mobile helium clusters (He{sub n}, 4 ≤ n ≤ 7) near low-Miller-index tungsten (W) surfaces, aiming at a fundamental understanding of the near-surface dynamics of helium-carrying species in plasma-exposed tungsten. These small mobile helium clusters are attracted to the surface and migrate to the surface by Fickian diffusion and drift due to the thermodynamic driving force for surface segregation. As the clusters migrate toward the surface, trap mutation (TM) and cluster dissociation reactions are activated at rates higher than in the bulk. TM produces W adatoms and immobile complexes of helium clusters surrounding W vacancies located within the lattice planes at a short distance from the surface. These reactions are identified and characterized in detail based on the analysis of a large number of molecular-dynamics trajectories for each such mobile cluster near W(100), W(110), and W(111) surfaces. TM is found to be the dominant cluster reaction for all cluster and surface combinations, except for the He{sub 4} and He{sub 5} clusters near W(100) where cluster partial dissociation following TM dominates. We find that there exists a critical cluster size, n = 4 near W(100) and W(111) and n = 5 near W(110), beyond which the formation of multiple W adatoms and vacancies in the TM reactions is observed. The identified cluster reactions are responsible for important structural, morphological, and compositional features in the plasma-exposed tungsten, including surface adatom populations, near-surface immobile helium-vacancy complexes, and retained helium content, which are expected to influence the amount of hydrogen re-cycling and tritium retention in fusion tokamaks.

Inflammatory reaction in chondroblastoma

International Nuclear Information System (INIS)

Yamamura, Sigeki; Sato, Keiji; Sugiura, Hideshi; Iwata, Hisashi

1996-01-01

The objective of this study was to evaluate the inflammatory reaction accompanying chondroblastoma and to define the value of the finding in clinical practice. We reviewed the clinical, radiographic, and magnetic resonance (MR) findings in six patients with histologically proven chondroblastoma. In all cases, MR imaging showered marrow and soft tissue edema. In four of six cases, periosteal reaction related to intra-osseous edema was more clearly demonstrated on MR imaging than on radiographs. Follow-up MR studies after surgery were available in three patients and all showed disappearance of inflammatory responses such as marrow and soft tissue edema, and reactive synovitis. We propose that these inflammatory reactions of chondroblastomas are inportant signs for detecting residual tumor in recurrences after surgery, as well as for making a precise diagnosis. The MR changes may also be valuable in demonstrating eradication of the tumor. (orig./MG)

Inflammatory reaction in chondroblastoma

Energy Technology Data Exchange (ETDEWEB)

Yamamura, Sigeki [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Sato, Keiji [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Sugiura, Hideshi [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Iwata, Hisashi [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan)

1996-05-01

The objective of this study was to evaluate the inflammatory reaction accompanying chondroblastoma and to define the value of the finding in clinical practice. We reviewed the clinical, radiographic, and magnetic resonance (MR) findings in six patients with histologically proven chondroblastoma. In all cases, MR imaging showered marrow and soft tissue edema. In four of six cases, periosteal reaction related to intra-osseous edema was more clearly demonstrated on MR imaging than on radiographs. Follow-up MR studies after surgery were available in three patients and all showed disappearance of inflammatory responses such as marrow and soft tissue edema, and reactive synovitis. We propose that these inflammatory reactions of chondroblastomas are inportant signs for detecting residual tumor in recurrences after surgery, as well as for making a precise diagnosis. The MR changes may also be valuable in demonstrating eradication of the tumor. (orig./MG)

Applications of Nuclear Reaction Analysis for Semiconductor Industry

International Nuclear Information System (INIS)

Wei Luncun

2003-01-01

Many thin film samples used in the semiconductor industry contain C, N and O. The detection limits and accuracy obtained by Rutherford Backscattering Spectroscopy (RBS) measurement are limited due to the small cross section values. High energy non-Rutherford backscattering is often used to enhance the sensitivities. But non-Rutherford cross section values are irregular and can not be calculated as normal Rutherford backscattering values. It is also difficult to find an appropriate energy window that for all these elements, and high-energy ions are needed. In this paper, the Nuclear Reaction Analysis (NRA) method is used to simultaneously measure C, N and O. several applications in the semiconductor research, development, and manufacturing areas are presented

Analysis of agility, reaction time and balance variables at badminton players aged 9-14 years

Directory of Open Access Journals (Sweden)

Seydi Ahmet Ağaoğlu

2017-12-01

Full Text Available Aim: The aim of this study was investigated agility, static and dynamic balance and reaction time variables of badminton players aged between 9-14 and relate with among variables. Material and Methods: In Samsun, 19 males (sport age, 3.42±1.64 years and 12 females (3.00±1.28 years active badminton players were voluntarily participated in who are in 9-14 ages range. Agility was measured by “T” test, CSMI-Tecnobody Pk-252 isokinetic balance system measuring instrument was used to test static balance and dynamic balance and Mozart Lafayette reaction measuring instrument was used to test visual and auditory reaction times of players. Spearman correlation analysis was applied so as to correlation analysis. The level of significance was taken as p<0.05. Results: For female athletes, a positive relation was determined between the agility and the perimeter (mm used (r=0.727; p<0.01 through the static balance measure double foot and eyes are open. For male athletes, a positive relation was determined between the visual reaction time and the perimeter (mm used (r=0.725; p<0.01 through the static balance measure dominant foot and eyes are open. For male and female athletes were not found any correlation between reaction time and dynamic balance. Conclusion: It was determined that audio (ears and visual (eyes reaction time was effective on balance. While badminton players are closed eyes, audio sensors are more influence on balance test through measure dominant foot.

GC of catalytic reactions products involved in the promising fuel synthesis

Energy Technology Data Exchange (ETDEWEB)

Zheivot, V.; Sazonova, N. [Russian Academy of Sciences, Novosibirsk (Russian Federation). Boreskov Inst. of Catalysis

2012-09-15

Catalytic reactions involved in the synthesis of the promising kinds of novel fuel and products formed in these reactions were systematized according to the resulting fuel type. Generalization of the retention of the substances comprising these products is presented. Chromatograms exhibiting their separation on chromatographic materials with the surface of different chemical properties are summarized. We propose procedures for gas-chromatographic analysis of the catalytic reactions products formed in the synthesis of hydrogen, methanol, dimethyl ether and hydrocarbons as a new generation of fuel alternative to petroleum and coal. For partial oxidation of methane into synthesis gas, on-line determination of the components obtained in the reaction was carried out by gas chromatography and gas analyzer based on different physicochemical methods (IR spectroscopy and electrochemical methods). Similarity of the results obtained using these methods is demonstrated. (orig.)

Analysis of the consequences of 'thermite' reaction

International Nuclear Information System (INIS)

Yorio, Daniel; Cincotta, Daniel O.; Camacho, Esteban F.; Bruno, Hernan R.; Boero, Norma L.

1999-01-01

The mixture of Al-U 3 O 8 is not in a state of chemical equilibrium, and at temperatures of between 850 degree C and 1000 degree C, it reacts exo thermally. This is known, in corresponding bibliography, as a 'Thermite reaction'. This mixture is used in the manufacturing of the plate-type fuel used in research reactors. It has been pointed out that the release of energy caused by this type of reactions might represent a risk in case of accidents in this type of reactor. Conclusions, in general, tend to indicate that no such risk exists, although no concrete assurance is given that this is the case, and this fact, therefore, leaves room for doubt. The objective of this paper is to provide an in-depth study of what happens to a fuel plate when it is subjected to thermite reaction. We will, furthermore, analyze the consequences of the release of energy generated by this type of reaction within the core of the reactor, clearly defining the problem for this type of fuel and this kind of reactor

Stochastic modeling and simulation of reaction-diffusion system with Hill function dynamics.

Science.gov (United States)

Chen, Minghan; Li, Fei; Wang, Shuo; Cao, Young

2017-03-14

Stochastic simulation of reaction-diffusion systems presents great challenges for spatiotemporal biological modeling and simulation. One widely used framework for stochastic simulation of reaction-diffusion systems is reaction diffusion master equation (RDME). Previous studies have discovered that for the RDME, when discretization size approaches zero, reaction time for bimolecular reactions in high dimensional domains tends to infinity. In this paper, we demonstrate that in the 1D domain, highly nonlinear reaction dynamics given by Hill function may also have dramatic change when discretization size is smaller than a critical value. Moreover, we discuss methods to avoid this problem: smoothing over space, fixed length smoothing over space and a hybrid method. Our analysis reveals that the switch-like Hill dynamics reduces to a linear function of discretization size when the discretization size is small enough. The three proposed methods could correctly (under certain precision) simulate Hill function dynamics in the microscopic RDME system.

Online monitoring of chemical reactions by polarization-induced electrospray ionization.

Science.gov (United States)

Meher, Anil Kumar; Chen, Yu-Chie

2016-09-21

Polarization-induced electrospray ionization (PI-ESI) is a simple technique for instant generation of gas-phase ions directly from a microliter-sized droplet for mass spectrometric analysis. A sample droplet was placed over a dielectric substrate and in proximity (2-3 mm) to the inlet of a mass spectrometer. Owing to the polarization effect induced by the high electric field provided by the mass spectrometer, the droplet was polarized and the electrospray was generated from the apex of the droplet. The polarization-induced electrospray could last for tens of seconds, which was sufficiently long to monitor fast reactions occurring within few seconds. Thus, we demonstrated the feasibility of using the droplet-based PI-ESI MS for the online monitoring of fast reactions by simply mixing two droplets (5-10 μL) containing reactants on a dielectric substrate placed in front of a mass spectrometer applied with a high voltage (-4500 V). Schiff base reactions and oxidation reactions that can generate intermediates/products within a few seconds were selected as the model reactions. The ionic reaction species generated from intermediates and products can be simultaneously monitored by PI-ESI MS in real time. We also used this approach to selectively detect acetone from a urine sample, in which acetone was derivatized in situ. In addition, the possibility of using this approach for quantitative analysis of acetone from urine samples was examined. Copyright © 2016 Elsevier B.V. All rights reserved.

A Demonstration of Concrete Structural Health Monitoring Framework for Degradation due to Alkali-Silica Reaction

Energy Technology Data Exchange (ETDEWEB)

Mahadevan, Sankaran [Idaho National Lab. (INL), Idaho Falls, ID (United States); Agarwal, Vivek [Idaho National Lab. (INL), Idaho Falls, ID (United States); Neal, Kyle [Idaho National Lab. (INL), Idaho Falls, ID (United States); Nath, Paromita [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bao, Yanqing [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cai, Guowei [Idaho National Lab. (INL), Idaho Falls, ID (United States); Orme, Peter [Idaho National Lab. (INL), Idaho Falls, ID (United States); Adams, Douglas [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kosson, David [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-04-01

Assessment and management of aging concrete structures in nuclear power plants require a more systematic approach than simple reliance on existing code margins of safety. Structural health monitoring of concrete structures aims to understand the current health condition of a structure based on heterogeneous measurements to produce high-confidence actionable information regarding structural integrity that supports operational and maintenance decisions. This ongoing research project is seeking to develop a probabilistic framework for health diagnosis and prognosis of aging concrete structures in a nuclear power plant that is subjected to physical, chemical, environment, and mechanical degradation. The proposed framework consists of four elements: monitoring, data analytics, uncertainty quantification and prognosis. This report focuses on degradation caused by ASR (alkali-silica reaction). Controlled specimens were prepared to develop accelerated ASR degradation. Different monitoring techniques – thermography, digital image correlation (DIC), mechanical deformation measurements, nonlinear impact resonance acoustic spectroscopy (NIRAS), and vibro-acoustic modulation (VAM) -- were used to detect the damage caused by ASR. Heterogeneous data from the multiple techniques was used for damage diagnosis and prognosis, and quantification of the associated uncertainty using a Bayesian network approach. Additionally, MapReduce technique has been demonstrated with synthetic data. This technique can be used in future to handle large amounts of observation data obtained from the online monitoring of realistic structures.

Automated selected reaction monitoring data analysis workflow for large-scale targeted proteomic studies.

Science.gov (United States)

Surinova, Silvia; Hüttenhain, Ruth; Chang, Ching-Yun; Espona, Lucia; Vitek, Olga; Aebersold, Ruedi

2013-08-01

Targeted proteomics based on selected reaction monitoring (SRM) mass spectrometry is commonly used for accurate and reproducible quantification of protein analytes in complex biological mixtures. Strictly hypothesis-driven, SRM assays quantify each targeted protein by collecting measurements on its peptide fragment ions, called transitions. To achieve sensitive and accurate quantitative results, experimental design and data analysis must consistently account for the variability of the quantified transitions. This consistency is especially important in large experiments, which increasingly require profiling up to hundreds of proteins over hundreds of samples. Here we describe a robust and automated workflow for the analysis of large quantitative SRM data sets that integrates data processing, statistical protein identification and quantification, and dissemination of the results. The integrated workflow combines three software tools: mProphet for peptide identification via probabilistic scoring; SRMstats for protein significance analysis with linear mixed-effect models; and PASSEL, a public repository for storage, retrieval and query of SRM data. The input requirements for the protocol are files with SRM traces in mzXML format, and a file with a list of transitions in a text tab-separated format. The protocol is especially suited for data with heavy isotope-labeled peptide internal standards. We demonstrate the protocol on a clinical data set in which the abundances of 35 biomarker candidates were profiled in 83 blood plasma samples of subjects with ovarian cancer or benign ovarian tumors. The time frame to realize the protocol is 1-2 weeks, depending on the number of replicates used in the experiment.

DEMONSTRATION BULLETIN: ADSORPTION-INTEGRATED-REACTION (AIR2000) PROCESS, KSE, INC.

Science.gov (United States)

This Bulletin is a brief description of the AIR2000 technology developed by KSE, Inc., of Amherst, MA. The AIR2000 unit treats air streams containing volatile organic compounds (VOCs). The demonstration occurred at the Stamina Mills superfund site in North Smithfield, RI from Aug...

Quantitative Analysis of Homogeneous Electrocatalytic Reactions at IDA Electrodes: The Example of [Ni(PPh2NBn2)2]2+

Energy Technology Data Exchange (ETDEWEB)

Liu, Fei; Parkinson, B. A.; Divan, Ralu; Roberts, John; Liang, Yanping

2016-12-01

Interdigitated array (IDA) electrodes have been applied to study the EC’ (electron transfer reaction followed by a catalytic reaction) reactions and a new method of quantitative analysis of IDA results was developed. In this new method, currents on IDA generator and collector electrodes for an EC’ mechanism are derived from the number of redox cycles and the contribution of non-catalytic current. And the fractions of bipotential recycling species and catalytic-active species are calculated, which helps understanding the catalytic reaction mechanism. The homogeneous hydrogen evolution reaction catalyzed by [Ni(PPh2NBn2)2]2+ (where PPh2NBn2 is 1,5-dibenzyl-3,7-diphenyl-1,5-diaza-3,7-diphosphacyclooctane) electrocatalyst was examined and analyzed with IDA electrodes. Besides, the existence of reaction intermediates in the catalytic cycle is inferred from the electrochemical behavior of a glassy carbon disk electrodes and carbon IDA electrodes. This quantitative analysis of IDA electrode cyclic voltammetry currents can be used as a simple and straightforward method for determining reaction mechanism in other catalytic systems as well.

Quantitative Analysis of Homogeneous Electrocatalytic Reactions at IDA Electrodes: The Example of [Ni(PPh2NBn2)2]2+

International Nuclear Information System (INIS)

Liu, Fei; Parkinson, B.A.; Divan, Ralu; Roberts, John; Liang, Yanping

2016-01-01

Interdigitated array (IDA) electrodes have been applied to study the EC’ (electron transfer reaction followed by a catalytic reaction) reactions and a new method of quantitative analysis of IDA results was developed. In this new method, currents on IDA generator and collector electrodes for an EC’ mechanism are derived from the number of redox cycles and the contribution of non-catalytic current. And the fractions of bipotential recycling species and catalytic-active species are calculated, which helps understanding the catalytic reaction mechanism. The homogeneous hydrogen evolution reaction catalyzed by [Ni(P Ph 2 N Bn 2 ) 2 ] 2+ (where P Ph 2 N Bn 2 is 1,5-dibenzyl-3,7-diphenyl-1,5-diaza-3,7-diphosphacyclooctane) electrocatalyst was examined and analyzed with IDA electrodes. Besides, the existence of reaction intermediates in the catalytic cycle is inferred from the electrochemical behavior of a glassy carbon disk electrodes and carbon IDA electrodes. This quantitative analysis of IDA electrode cyclic voltammetry currents can be used as a simple and straightforward method for determining reaction mechanism in other catalytic systems as well.

Using Musical Intervals to Demonstrate Superposition of Waves and Fourier Analysis

Science.gov (United States)

LoPresto, Michael C.

2013-01-01

What follows is a description of a demonstration of superposition of waves and Fourier analysis using a set of four tuning forks mounted on resonance boxes and oscilloscope software to create, capture and analyze the waveforms and Fourier spectra of musical intervals.

AZ-101 Mixer Pump Demonstration and Tests Data Management Analysis Plan

Energy Technology Data Exchange (ETDEWEB)

DOUGLAS, D.G.

2000-02-22

This document provides a plan for the analysis of the data collected during the AZ-101 Mixer Pump Demonstration and Tests. This document was prepared after a review of the AZ-101 Mixer Pump Test Plan (Revision 4) [1] and other materials. The plan emphasizes a structured and well-ordered approach towards handling and examining the data. This plan presumes that the data will be collected and organized into a unified body of data, well annotated and bearing the date and time of each record. The analysis of this data will follow a methodical series of steps that are focused on well-defined objectives. Section 2 of this plan describes how the data analysis will proceed from the real-time monitoring of some of the key sensor data to the final analysis of the three-dimensional distribution of suspended solids. This section also identifies the various sensors or sensor systems and associates them with the various functions they serve during the test program. Section 3 provides an overview of the objectives of the AZ-101 test program and describes the data that will be analyzed to support that test. The objectives are: (1) to demonstrate that the mixer pumps can be operated within the operating requirements; (2) to demonstrate that the mixer pumps can mobilize the sludge in sufficient quantities to provide feed to the private contractor facility, and (3) to determine if the in-tank instrumentation is sufficient to monitor sludge mobilization and mixer pump operation. Section 3 also describes the interim analysis that organizes the data during the test, so the analysis can be more readily accomplished. Section 4 describes the spatial orientation of the various sensors in the tank. This section is useful in visualizing the relationship of the Sensors in terms of their location in the tank and how the data from these sensors may be related to the data from other sensors. Section 5 provides a summary of the various analyses that will be performed on the data during the test

AZ-101 Mixer Pump Demonstration and Tests: Data Management (Analysis) Plan

International Nuclear Information System (INIS)

DOUGLAS, D.G.

2000-01-01

This document provides a plan for the analysis of the data collected during the AZ-101 Mixer Pump Demonstration and Tests. This document was prepared after a review of the AZ-101 Mixer Pump Test Plan (Revision 4) [1] and other materials. The plan emphasizes a structured and well-ordered approach towards handling and examining the data. This plan presumes that the data will be collected and organized into a unified body of data, well annotated and bearing the date and time of each record. The analysis of this data will follow a methodical series of steps that are focused on well-defined objectives. Section 2 of this plan describes how the data analysis will proceed from the real-time monitoring of some of the key sensor data to the final analysis of the three-dimensional distribution of suspended solids. This section also identifies the various sensors or sensor systems and associates them with the various functions they serve during the test program. Section 3 provides an overview of the objectives of the AZ-101 test program and describes the data that will be analyzed to support that test. The objectives are: (1) to demonstrate that the mixer pumps can be operated within the operating requirements; (2) to demonstrate that the mixer pumps can mobilize the sludge in sufficient quantities to provide feed to the private contractor facility, and (3) to determine if the in-tank instrumentation is sufficient to monitor sludge mobilization and mixer pump operation. Section 3 also describes the interim analysis that organizes the data during the test, so the analysis can be more readily accomplished. Section 4 describes the spatial orientation of the various sensors in the tank. This section is useful in visualizing the relationship of the Sensors in terms of their location in the tank and how the data from these sensors may be related to the data from other sensors. Section 5 provides a summary of the various analyses that will be performed on the data during the test

Incomplete fusion reactions in 16O+159Tb system: Spin distribution measurements

Directory of Open Access Journals (Sweden)

Sharma Vijay R.

2015-01-01

Full Text Available In order to explore the reaction modes on the basis of their entry state spin population, an experiment has been done by employing particle-γ coincidence technique carried out at the Inter University Accelerator Centre, New Delhi. The preliminary analysis conclusively demonstrates, spin distribution for some reaction products populated via complete and/or incomplete fusion of 16O with 159Tb system found to be distinctly different. Further, the existence of incomplete fusion at low bombarding energies indicates the possibility to populate high spin states.

The reaction π-p → π-π-π+p: Development of the analysis methods and selected results

Science.gov (United States)

Ryabchikov, D.

2016-01-01

We present the description of the analysis methods and results of applying them to the exclusive diffractive reaction π-p → π-π-π+p of 50 . 106 events measured with COMPASS detector. The large statistics of π-π-π+ events enables the two-dimensional partial-wave analysis independently in 100 bins of m(3π) with 0.5 < m(3π) < 2.5 GeV/c2 and in 11 intervals of squared momentum transfer with 0.1 < t' < 1 GeV2/c2. The partial-wave analysis sub-density matrix is the subject to further mass-dependent fits describing the data in terms of resonances in 3π system and coherent background contributions. The novel approach of extracting JPC = 0++(π+π-)S isobar amplitudes as model-free functions, different for several JPC 3π states, is used. It demonstrates the presence of processes π(1800) → f0(980)π and π(1800) → f0(1500)π as well as π2(1880) → f0(980)π and new narrow signal a1(1420) → f0(980)π, without any established shapes used for (π+π-)S isobars. The presented analysis is subject to further development and refinements which currently take place.

The dynamics of the Hg + Br2 reaction: elucidation of the reaction mechanism for the Br exchange reaction.

Science.gov (United States)

Jambrina, P G; Menéndez, M; Aoiz, F J

2017-06-28

In spite of its importance in the Hg atmospheric chemistry, the dynamics of the Hg + Br 2 → HgBr + Br reaction is poorly understood. In this article, we have carried out a comprehensive study of the reaction mechanism of this reaction by means of quasiclassical trajectories (QCTs) on an existing ab initio potential energy surface (PES). The reaction has a non trivial dynamics, as a consequence of its large endothermicity, the presence of a deep potential well, and the competition between the Br exchange and the collision induced dissociation processes. Our calculations demonstrate that insertion is only relevant at energies just above the reaction threshold and that, at energies above 2.3 eV, HgBr formation typically takes place via a sort of frustrated dissociation. In order to compare directly with the results obtained in extensive cross molecular beam experiments for the homologous reaction with I 2 , angular distributions in the laboratory frame for Hg + Br 2 have been simulated under similar experimental conditions. The lack of agreement at the highest energies considered suggests that either the two reactions have substantially different mechanisms or that calculations on a single PES cannot account for the dynamics at those energies.

Global Controllability of Chemical Reactions

OpenAIRE

Drexler, Dániel András; Tóth, János

2015-01-01

Controllability of chemical reactions is an important problem in chemical engineering science. In control theory, analysis of the controllability of linear systems is well-founded, however the dynamics of chemical reactions is usually nonlinear. Global controllability properties of chemical reactions are analyzed here based on the Lie-algebra of the vector fields associated to elementary reactions. A chemical reaction is controllable almost everywhere if all the reaction rate coefficients can...

Cintichem modified process - {sup 99}Mo precipitation step: application of statistical analysis tools over the reaction parameters

Energy Technology Data Exchange (ETDEWEB)

Teodoro, Rodrigo; Dias, Carla R.B.R.; Osso Junior, Joao A., E-mail: jaosso@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Fernandez Nunez, Eutimio Gustavo [Universidade de Sao Paulo (EP/USP), SP (Brazil). Escola Politecnica. Dept. de Engenharia Quimica

2011-07-01

Precipitation of {sup 99}Mo by {alpha}-benzoin oxime ({alpha}-Bz) is a standard precipitation method for molybdenum due the high selectivity of this agent. Nowadays, statistical analysis tools have been employed in analytical systems to prove its efficiency and feasibility. IPEN has a project aiming the production of {sup 99}Mo by the fission of {sup 235}U route. The processing uses as the first step the precipitation of {sup 99}Mo with {alpha}-Bz. This precipitation step involves many key reaction parameters. The aim of this work is based on the development of the already known acidic route to produce {sup 99}Mo as well as the optimization of the reactional parameters applying statistical tools. In order to simulate {sup 99}Mo precipitation, the study was conducted in acidic media using HNO{sub 3}, {alpha}Bz as precipitant agent and NaOH /1%H{sub 2}O{sub 2} as dissolver solution. Then, a Mo carrier, KMnO{sub 4} solutions and {sup 99}Mo tracer were added to the reaction flask. The reactional parameters ({alpha}-Bz/Mo ratio, Mo carrier, reaction time and temperature, and cooling reaction time before filtration) were evaluated under a fractional factorial design of resolution V. The best values of each reactional parameter were determined by a response surface statistical planning. The precipitation and recovery yields of {sup 99}Mo were measured using HPGe detector. Statistical analysis from experimental data suggested that the reactional parameters {alpha}-Bz/Mo ratio, reaction time and temperature have a significant impact on {sup 99}Mo precipitation. Optimization statistical planning showed that higher {alpha}Bz/Mo ratios, room temperature, and lower reaction time lead to higher {sup 99}Mo yields. (author)

Stability Analysis of a Reaction-Diffusion System Modeling Atherogenesis

KAUST Repository

Ibragimov, Akif

2010-01-01

This paper presents a linear, asymptotic stability analysis for a reaction-diffusionconvection system modeling atherogenesis, the initiation of atherosclerosis, as an inflammatory instability. Motivated by the disease paradigm articulated by Ross, atherogenesis is viewed as an inflammatory spiral with a positive feedback loop involving key cellular and chemical species interacting and reacting within the intimal layer of muscular arteries. The inflammatory spiral is initiated as an instability from a healthy state which is defined to be an equilibrium state devoid of certain key inflammatory markers. Disease initiation is studied through a linear, asymptotic stability analysis of a healthy equilibrium state. Various theorems are proved, giving conditions on system parameters guaranteeing stability of the health state, and a general framework is developed for constructing perturbations from a healthy state that exhibit blow-up, which are interpreted as corresponding to disease initiation. The analysis reveals key features that arterial geometry, antioxidant levels, and the source of inflammatory components (through coupled third-kind boundary conditions or through body sources) play in disease initiation. © 2010 Society for Industrial and Applied Mathematics.

Simplified method of ''push-pull'' test data analysis for determining in situ reaction rate coefficients

International Nuclear Information System (INIS)

Haggerty, R.; Schroth, M.H.; Istok, J.D.

1998-01-01

The single-well, ''''push-pull'''' test method is useful for obtaining information on a wide variety of aquifer physical, chemical, and microbiological characteristics. A push-pull test consists of the pulse-type injection of a prepared test solution into a single monitoring well followed by the extraction of the test solution/ground water mixture from the same well. The test solution contains a conservative tracer and one or more reactants selected to investigate a particular process. During the extraction phase, the concentrations of tracer, reactants, and possible reaction products are measured to obtain breakthrough curves for all solutes. This paper presents a simplified method of data analysis that can be used to estimate a first-order reaction rate coefficient from these breakthrough curves. Rate coefficients are obtained by fitting a regression line to a plot of normalized concentrations versus elapsed time, requiring no knowledge of aquifer porosity, dispersivity, or hydraulic conductivity. A semi-analytical solution to the advective-dispersion equation is derived and used in a sensitivity analysis to evaluate the ability of the simplified method to estimate reaction rate coefficients in simulated push-pull tests in a homogeneous, confined aquifer with a fully-penetrating injection/extraction well and varying porosity, dispersivity, test duration, and reaction rate. A numerical flow and transport code (SUTRA) is used to evaluate the ability of the simplified method to estimate reaction rate coefficients in simulated push-pull tests in a heterogeneous, unconfined aquifer with a partially penetrating well. In all cases the simplified method provides accurate estimates of reaction rate coefficients; estimation errors ranged from 0.1 to 8.9% with most errors less than 5%

Nuclear reactions excited by recoil protons on a nuclear reactor

International Nuclear Information System (INIS)

Mukhammedov, S.; Khaydarov, A.; Barsukova, E.G.

2006-01-01

The nuclear reactions excited by recoil protons and of the detection possibility of the various chemical elements with the use of these secondary nucleus reactions were investigated. The recoil protons are produced on a nuclear reactor in the result of (n, p) inelastic and elastic scattering interaction of fast neutrons with nuclei of hydrogen. It is well known that the share of fast neutrons in energetic spectrum of reactor's neutrons in comparison with the share of thermal neutrons is small. . Consequently, the share of recoil protons produced in the result of fast neutron interaction with nuclei of light elements, capable to cause the nuclear reactions, is also small, des, due to Coulomb barrier of nuclei the recoil protons can cause the nuclear reactions only on nuclei of light and some middle elements. Our studies show that observable yields have radio nuclides excited in the result of nuclear reactions on Li, B, O, V and Cu. Our experimental results have demonstrated that the proton activation analysis based on the application of secondary nuclear reactions is useful technique to determine large contents of various light and medium chemical elements. Detection limits for studied chemical elements are estimated better than 10 ppm

Analysis of the fuel influence in obtaining HAp by combustion reaction

International Nuclear Information System (INIS)

Santos, T.L.; Leite, A.M.D.; Viana, K.M.S.

2016-01-01

The search for new materials for biomedical applications has led to investigation of the calcium phosphate bioceramics, and in particular hydroxyapatite (HAp), being a material similar to bone tissue, with excellent biocompatibility and high osteoconduction, enabling bone regeneration which allows the use at implants and prostheses. The synthesis of the nanometric HAp by combustion reaction enables obtaining the nanometric HAp with a more similar structure biological apatite as possible. This work aims to synthesize HAp by combustion reaction using two different routes of synthesis, first, using urea as fuel and the second using glycine, after this, evaluate the influence of fuels used in the microstructure of the hydroxyapatite obtained. The HAp obtained was characterized by: XRD, FTIR and SEM. Through analysis of the results, there is the synthesis conditions used that glycine has performed more favorable to obtaining HAp. (author)

Enzymatic solubilisation and degradation of soybean fibre demonstrated by viscosity, fibre analysis and microscopy

DEFF Research Database (Denmark)

Ravn, Jonas Laukkonen; Martens, Helle Juel; Pettersson, Dan

2015-01-01

The effect of a commercial multienzyme product obtained by fermentation from Aspergillus aculeatus on soybean and soybean meal was investigated using viscosity measurements, dietary fibre component analysis and different microscopy techniques utilizing histochemical dyes and antibody labelling....... The results obtained demonstrated a strong viscosity reducing effect of the enzyme preparation on soluble galactomannan and xyloglucan polysaccharides and in addition non-starch polysaccharide analysis demonstrated a notable solubilisation of all polysaccharide constituents. The degradation...

Chemical Characterization and Reactivity of Fuel-Oxidizer Reaction Product

Science.gov (United States)

David, Dennis D.; Dee, Louis A.; Beeson, Harold D.

1997-01-01

Fuel-oxidizer reaction product (FORP), the product of incomplete reaction of monomethylhydrazine and nitrogen tetroxide propellants prepared under laboratory conditions and from firings of Shuttle Reaction Control System thrusters, has been characterized by chemical and thermal analysis. The composition of FORP is variable but falls within a limited range of compositions that depend on three factors: the fuel-oxidizer ratio at the time of formation; whether the composition of the post-formation atmosphere is reducing or oxidizing; and the reaction or post-reaction temperature. A typical composition contains methylhydrazinium nitrate, ammonium nitrate, methylammonium nitrate, and trace amounts of hydrazinium nitrate and 1,1-dimethylhydrazinium nitrate. Thermal decomposition reactions of the FORP compositions used in this study were unremarkable. Neither the various compositions of FORP, the pure major components of FORP, nor mixtures of FORP with propellant system corrosion products showed any unusual thermal activity when decomposed under laboratory conditions. Off-limit thruster operations were simulated by rapid mixing of liquid monomethylhydrazine and liquid nitrogen tetroxide in a confined space. These tests demonstrated that monomethylhydrazine, methylhydrazinium nitrate, ammonium nitrate, or Inconel corrosion products can induce a mixture of monomethylhydrazine and nitrogen tetroxide to produce component-damaging energies. Damaging events required FORP or metal salts to be present at the initial mixing of monomethylhydrazine and nitrogen tetroxide.

Modelling and simulation of a transketolase mediated reaction: Sensitivity analysis of kinetic parameters

DEFF Research Database (Denmark)

Sayar, N.A.; Chen, B.H.; Lye, G.J.

2009-01-01

In this paper we have used a proposed mathematical model, describing the carbon-carbon bond format ion reaction between beta-hydroxypyruvate and glycolaldehyde to synthesise L-erythrulose, catalysed by the enzyme transketolase, for the analysis of the sensitivity of the process to its kinetic...

Modeling and analysis of liquid deuterium-water reactions

International Nuclear Information System (INIS)

Taleyarkhan, R.P.

1995-01-01

This Presentation highlights the following: Overview of LD 2 -water reactions their connections to research reactors with cold sources; some key features and ingredients of vapor explosions in general; Examination of results of 1970 experiment at Grenoble Nuclear Research Center; Thermodynamic evaluations of energetics of explosive LD 2 -D 2 O reactions. This presentation concentrates only on the technical aspects of LD 2 /LH 2 - water reactions; it is not intended to draw/imply safety-related conclusions for research reactors

Studies in the reaction dynamics of beam-gas chemiluminescent reactions

International Nuclear Information System (INIS)

Prisant, M.G.

1984-01-01

This thesis develops techniques for the analysis and interpretation of data obtained from beam-gas chemiluminescence experiments. These techniques are applied to experimental studies of atom transfer reactions of the type A + BC → AB + C. A procedure is developed for determining the product rotational alignment in the center-of-mass frame from polarization measurements of chemiluminescent atom-diatom exchange reactions under beam-gas conditions. Knowledge of a vector property of a reaction, such as product alignment, provides information on the disposition of angular momentum by a chemical reaction. Fluorescence polarization and hence product alignment are measured for two prototype reactions. The reaction of metastable calcium atoms with hydrogen-chloride gas yields highly aligned calcium-chloride product which exhibits little variation of alignment with vibrational state. The reaction of ground-state calcium with fluorine gas yields moderately aligned product which shows strong variation of alignment with vibration. A multi-surface direct-interaction model is developed to interpret product alignment and population data. The predictions of this model for the reaction of calcium with fluorine show reasonable agreement with experiment

DNA Double-Strand Break Analysis by {gamma}-H2AX Foci: A Useful Method for Determining the Overreactors to Radiation-Induced Acute Reactions Among Head-and-Neck Cancer Patients

Energy Technology Data Exchange (ETDEWEB)

Goutham, Hassan Venkatesh; Mumbrekar, Kamalesh Dattaram [Division of Radiobiology and Toxicology, Manipal Life Sciences Centre, Manipal University, Manipal, Karnataka (India); Vadhiraja, Bejadi Manjunath [Manipal Hospital, Bangalore, Karnataka (India); Fernandes, Donald Jerard; Sharan, Krishna [Department of Radiotherapy and Oncology, Shiridi Sai Baba Cancer Hospital and Research Centre, Kasturba Hospital, Manipal, Karnataka (India); Kanive Parashiva, Guruprasad; Kapaettu, Satyamoorthy [Division of Biotechnology, Manipal Life Sciences Centre, Manipal University, Manipal, Karnataka (India); Bola Sadashiva, Satish Rao, E-mail: satishraomlsc@gmail.com [Division of Radiobiology and Toxicology, Manipal Life Sciences Centre, Manipal University, Manipal, Karnataka (India)

2012-12-01

Purpose: Interindividual variability in normal tissue toxicity during radiation therapy is a limiting factor for successful treatment. Predicting the risk of developing acute reactions before initiation of radiation therapy may have the benefit of opting for altered radiation therapy regimens to achieve minimal adverse effects with improved tumor cure. Methods and Materials: DNA double-strand break (DSB) induction and its repair kinetics in lymphocytes of head-and-neck cancer patients undergoing chemoradiation therapy was analyzed by counting {gamma}-H2AX foci, neutral comet assay, and a modified version of neutral filter elution assay. Acute normal tissue reactions were assessed by Radiation Therapy Oncology Group criteria. Results: The correlation between residual DSBs and the severity of acute reactions demonstrated that residual {gamma}-H2AX foci in head-and-neck cancer patients increased with the severity of oral mucositis and skin reaction. Conclusions: Our results suggest that {gamma}-H2AX analysis may have predictive implications for identifying the overreactors to mucositis and skin reactions among head-and-neck cancer patients prior to initiation of radiation therapy.

Performance demonstration program plan for RCRA constituent analysis of solidified wastes

International Nuclear Information System (INIS)

1995-06-01

Performance Demonstration Programs (PDPS) are designed to help ensure compliance with the Quality Assurance Objectives (QAOs) for the Waste Isolation Pilot Plant (WIPP). The PDPs are intended for use by the Department of Energy (DOE) Carlsbad Area Office (CAO) to assess and approve the laboratories and other measurement facilities supplying services for the characterization of WIPP TRU waste. The PDPs may also be used by CAO in qualifying laboratories proposing to supply additional analytical services that are required for other than waste characterization, such as WIPP site operations. The purpose of this PDP is to test laboratory performance for the analysis of solidified waste samples for TRU waste characterization. This performance will be demonstrated by the successful analysis of blind audit samples of simulated, solidified TRU waste according to the criteria established in this plan. Blind audit samples (hereinafter referred to as PDP samples) will be used as an independent means to assess laboratory performance regarding compliance with the QAOs. The concentration of analytes in the PDP samples will address levels of regulatory concern and will encompass the range of concentrations anticipated in actual waste characterization samples. Analyses that are required by the WIPP to demonstrate compliance with various regulatory requirements and which are included in the PDP must be performed by laboratories that demonstrate acceptable performance in the PDP. These analyses are referred to as WIPP analyses and the samples on which they are performed are referred to as WIPP samples for the balance of this document

Development of analysis model for mid and long-term effects of sodium water reaction event in LMR

International Nuclear Information System (INIS)

Eoh, Jae Hyuk; Sim, Yoon Sub; Kim, Seong O; Kim, Yeon Sik; Kim, Eui Kwang; Wi, Myung Hwan

2002-04-01

The Sodium-Water Reaction(SWR) is important in the design consideration of a LMR steam generator. To develop the analysis code for long-term effects of SWR, investigation on the characteristics of various SWR analysis code and the assessment of an analysis model for long term effects were performed. In an event of SWR, pressure spikes of wave propagation occur at its initial stage and last for a very short time, and then bulk motion of fluid and reaction products is progressed and lasts for a long time. In a case SWR occurs, a number of hydrogen bubbles produced and sodium is entrained into the bubbles through the gas-liquid bubble interfaces by evaporation or diffusion. The partial pressure of the sodium in a hydrogen bubble is determined as a function of the bubble size, temperature, and pressure, and is rapidly decreased as its size increased. From this, it can be considered that the bulk motion in the later phase of SWR is an axial motion caused by expansion of a single-phase hydrogen gas bubble produced by a reaction in the vicinity of the leak site. Through this investigation, a preliminary simple analysis model for long-term effects of SWR was set up and sensitivity study using the system design parameters such as pressure and temperature of IHTS for KALIMER was performed. Also, a simpler analysis model using the cover gas pressure change related to the production of a hydrogen bubble in a steam generator was developed from the analyses results. These simple analysis models of the reaction site and the pressure behavior with hydrogen production can be used to develop the mid and long-term analysis code for SWR in the KALIMER steam generator design

Performance Demonstration Program Plan for Analysis of Simulated Headspace Gases

International Nuclear Information System (INIS)

2006-01-01

The Performance Demonstration Program (PDP) for headspace gases distributes sample gases of volatile organic compounds (VOCs) for analysis. Participating measurement facilities (i.e., fixed laboratories, mobile analysis systems, and on-line analytical systems) are located across the United States. Each sample distribution is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements performed for transuranic (TRU) waste characterization. The primary documents governing the conduct of the PDP are the Quality Assurance Program Document (QAPD) (DOE/CBFO-94-1012) and the Waste Isolation Pilot Plant (WIPP) Waste Analysis Plan (WAP) contained in the Hazardous Waste Facility Permit (NM4890139088-TSDF) issued by the New Mexico Environment Department (NMED). The WAP requires participation in the PDP; the PDP must comply with the QAPD and the WAP. This plan implements the general requirements of the QAPD and the applicable requirements of the WAP for the Headspace Gas (HSG) PDP. Participating measurement facilities analyze blind audit samples of simulated TRU waste package headspace gases according to the criteria set by this PDP Plan. Blind audit samples (hereafter referred to as PDP samples) are used as an independent means to assess each measurement facility's compliance with the WAP quality assurance objectives (QAOs). To the extent possible, the concentrations of VOC analytes in the PDP samples encompass the range of concentrations anticipated in actual TRU waste package headspace gas samples. Analyses of headspace gases are required by the WIPP to demonstrate compliance with regulatory requirements. These analyses must be performed by measurement facilities that have demonstrated acceptable performance in this PDP. These analyses are referred to as WIPP analyses and the TRU waste package headspace gas samples on which they are performed are referred to as WIPP samples in this document. Participating measurement

Performance Demonstration Program Plan for Analysis of Simulated Headspace Gases

International Nuclear Information System (INIS)

2007-01-01

The Performance Demonstration Program (PDP) for headspace gases distributes blind audit samples in a gas matrix for analysis of volatile organic compounds (VOCs). Participating measurement facilities (i.e., fixed laboratories, mobile analysis systems, and on-line analytical systems) are located across the United States. Each sample distribution is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements performed for transuranic (TRU) waste characterization. The primary documents governing the conduct of the PDP are the Quality Assurance Program Document (QAPD) (DOE/CBFO-94-1012) and the Waste Isolation Pilot Plant (WIPP) Waste Analysis Plan (WAP) contained in the Hazardous Waste Facility Permit (NM4890139088-TSDF) issued by the New Mexico Environment Department (NMED). The WAP requires participation in the PDP; the PDP must comply with the QAPD and the WAP. This plan implements the general requirements of the QAPD and the applicable requirements of the WAP for the Headspace Gas (HSG) PDP. Participating measurement facilities analyze blind audit samples of simulated TRU waste package headspace gases according to the criteria set by this PDP Plan. Blind audit samples (hereafter referred to as PDP samples) are used as an independent means to assess each measurement facility's compliance with the WAP quality assurance objectives (QAOs). To the extent possible, the concentrations of VOC analytes in the PDP samples encompass the range of concentrations anticipated in actual TRU waste package headspace gas samples. Analyses of headspace gases are required by the WIPP to demonstrate compliance with regulatory requirements. These analyses must be performed by measurement facilities that have demonstrated acceptable performance in this PDP. These analyses are referred to as WIPP analyses and the TRU waste package headspace gas samples on which they are performed are referred to as WIPP samples in this document

Evaluation of reactor induced (n,p) reactions for activation analysis of titanium in geological materials

Energy Technology Data Exchange (ETDEWEB)

Espinosa Garcia, R; Cohen, I M [Comision Nacional de Energia Atomica, Buenos Aires (Argentina)

1984-05-01

The possibilities of reactor induced (n,p) reactions as a tool for neutron activation analysis of titanium in geological samples are discussed. The interference of calcium and scandium is experimentally evaluated. Results for Ti, Ca and Sc in GSP-1 and PCC-1 standard rocks are presented. Based on the experimental values, it is concluded that the /sup 47/Ti(n,p)/sup 47/Sc reaction is the most favourable for titanium determination. 11 refs.

Applications of nuclear reaction analysis for determining hydrogen and deuterium distribution in metals

International Nuclear Information System (INIS)

Altstetter, C.J.

1981-01-01

The use of ion beams for materials analysis has made a successful transition from the domain of the particle physicist to that of the materials scientist. The subcategory of this field, nuclear reaction analysis, is just now undergoing the transition, particularly in applications to hydrogen in materials. The materials scientist must locate the nearest accelerator, because now he will find that using it can solve mysteries that do not yield to other techniques. 9 figures

Nonimmediate hypersensitivity reactions to iodinated contrast media.

Science.gov (United States)

Gómez, Enrique; Ariza, Adriana; Blanca-López, Natalia; Torres, Maria J

2013-08-01

To provide a detailed analysis of the latest findings on the mechanisms underlying the nonimmediate reactions to iodinated contrast media and comment on the recent advances in diagnosis, focusing on the roles of the skin test, drug provocation test (DPT), and lymphocyte transformation test (LTT). Several studies have reported new findings supporting an important role for T-lymphocytes in the nonimmediate reactions to iodinated contrast media. The LTT has been used as an in-vitro tool for diagnosis, but with variable results. However, the inclusion of autologous monocyte-derived dendritic cells as professional antigen-presenting cells has improved the sensitivity of this test. Regarding in-vivo diagnosis, although skin testing has been routine, it has now been shown that its sensitivity and negative predictive value are low. Recent studies have demonstrated that the DPT is a well tolerated and useful procedure that is necessary to confirm the diagnosis of nonimmediate hypersensitivity reactions to iodinated contrast media. Nonimmediate reactions to contrast media are usually T-cell mediated. Diagnosis is based on skin testing, although its sensitivity and negative predictive value are not optimal. Consequently, drug provocation testing is often needed to confirm the diagnosis and also to seek alternative contrast media that can be tolerated.

Automated Microfluidic Platform for Serial Polymerase Chain Reaction and High-Resolution Melting Analysis.

Science.gov (United States)

Cao, Weidong; Bean, Brian; Corey, Scott; Coursey, Johnathan S; Hasson, Kenton C; Inoue, Hiroshi; Isano, Taisuke; Kanderian, Sami; Lane, Ben; Liang, Hongye; Murphy, Brian; Owen, Greg; Shinoda, Nobuhiko; Zeng, Shulin; Knight, Ivor T

2016-06-01

We report the development of an automated genetic analyzer for human sample testing based on microfluidic rapid polymerase chain reaction (PCR) with high-resolution melting analysis (HRMA). The integrated DNA microfluidic cartridge was used on a platform designed with a robotic pipettor system that works by sequentially picking up different test solutions from a 384-well plate, mixing them in the tips, and delivering mixed fluids to the DNA cartridge. A novel image feedback flow control system based on a Canon 5D Mark II digital camera was developed for controlling fluid movement through a complex microfluidic branching network without the use of valves. The same camera was used for measuring the high-resolution melt curve of DNA amplicons that were generated in the microfluidic chip. Owing to fast heating and cooling as well as sensitive temperature measurement in the microfluidic channels, the time frame for PCR and HRMA was dramatically reduced from hours to minutes. Preliminary testing results demonstrated that rapid serial PCR and HRMA are possible while still achieving high data quality that is suitable for human sample testing. © 2015 Society for Laboratory Automation and Screening.

MONITORING POTENTIAL DRUG INTERACTIONS AND REACTIONS VIA NETWORK ANALYSIS OF INSTAGRAM USER TIMELINES.

Science.gov (United States)

Correia, Rion Brattig; Li, Lang; Rocha, Luis M

2016-01-01

Much recent research aims to identify evidence for Drug-Drug Interactions (DDI) and Adverse Drug reactions (ADR) from the biomedical scientific literature. In addition to this "Bibliome", the universe of social media provides a very promising source of large-scale data that can help identify DDI and ADR in ways that have not been hitherto possible. Given the large number of users, analysis of social media data may be useful to identify under-reported, population-level pathology associated with DDI, thus further contributing to improvements in population health. Moreover, tapping into this data allows us to infer drug interactions with natural products-including cannabis-which constitute an array of DDI very poorly explored by biomedical research thus far. Our goal is to determine the potential of Instagram for public health monitoring and surveillance for DDI, ADR, and behavioral pathology at large. Most social media analysis focuses on Twitter and Facebook, but Instagram is an increasingly important platform, especially among teens, with unrestricted access of public posts, high availability of posts with geolocation coordinates, and images to supplement textual analysis. Using drug, symptom, and natural product dictionaries for identification of the various types of DDI and ADR evidence, we have collected close to 7000 user timelines spanning from October 2010 to June 2015.We report on 1) the development of a monitoring tool to easily observe user-level timelines associated with drug and symptom terms of interest, and 2) population-level behavior via the analysis of co-occurrence networks computed from user timelines at three different scales: monthly, weekly, and daily occurrences. Analysis of these networks further reveals 3) drug and symptom direct and indirect associations with greater support in user timelines, as well as 4) clusters of symptoms and drugs revealed by the collective behavior of the observed population. This demonstrates that Instagram

Identification of reaction products from reactions of free chlorine with the lipid-regulator gemfibrozil.

Science.gov (United States)

Krkošek, Wendy H; Koziar, Stephen A; White, Robert L; Gagnon, Graham A

2011-01-01

High global consumption rates have led to the occurrence of pharmaceutically active compounds (PhACs) in wastewater. The use of chlorine to disinfect wastewater prior to release into the environment may convert PhACs into uncharacterized chlorinated by-products. In this investigation, chlorination of a common pharmaceutical, the antihyperlipidemic agent gemfibrozil, was documented. Gemfibrozil (2,2-dimethyl-5-(2,5-dimethylphenoxy)pentanoic acid) was reacted with sodium hypochlorite and product formation was monitored by gas chromatography-mass spectrometry (GC-MS). The incorporation of one, two or three chlorine atoms into the aromatic region of gemfibrozil was demonstrated using negative-ion electrospray ionization mass spectrometry (ESI-MS) and tandem mass spectrometry (ESI-MS/MS). Further analysis using (1)H nuclear magnetic resonance (NMR) spectroscopy identified the reaction products as 4'-ClGem (5-(4-chloro-2,5-dimethylphenoxy)-2,2-dimethylpentanoic acid) 4',6'-diClGem (5-(4,6-dichloro-2,5-dimethylphenoxy)-2,2-dimethylpentanoic acid), and 3',4',6'-triClGem (5-(3,4,6-trichloro-2,5-dimethylphenoxy)-2,2-dimethylpentanoic acid), products consistent with electrophilic aromatic substitution reactions. The rapid reaction of gemfibrozil with free chlorine at pH conditions relevant to water treatment indicates that a mixture of chlorinated gemfibrozils is likely to be found in wastewater disinfected with chlorine. Copyright © 2010 Elsevier Ltd. All rights reserved.

Analysis of Brownian Dynamics Simulations of Reversible Bimolecular Reactions

KAUST Repository

Lipková, Jana

2011-01-01

A class of Brownian dynamics algorithms for stochastic reaction-diffusion models which include reversible bimolecular reactions is presented and analyzed. The method is a generalization of the λ-bcȳ model for irreversible bimolecular reactions which was introduced in [R. Erban and S. J. Chapman, Phys. Biol., 6(2009), 046001]. The formulae relating the experimentally measurable quantities (reaction rate constants and diffusion constants) with the algorithm parameters are derived. The probability of geminate recombination is also investigated. © 2011 Society for Industrial and Applied Mathematics.

In Situ Gaseous Reduction Pilot Demonstration - Final Report

International Nuclear Information System (INIS)

Thornton, E.C.; Phelan, J.M.; Giblin, J.T.; Olsen, K.B.; Miller, R.D.; Gilmore, T.J.

1999-01-01

The demonstration of the IGRS approach conducted at SWMU 143 on the White Sands Missile Range has provided information needed to complete a technical performance assessment and cost analysis of the technology. At least 70% of the Cr(VI) present in contaminated sediment at the site was reduced, thus verifying the effectiveness of the approach. Most of the treatment occurred in a zone located from approximately4 to 10 ft below ground surface, which appears to be a higher permeability interval. A deeper zone from approximately10 to 16 ft that contains lower levels of contamination was essentially unaffected. The deeper zone is somewhat finer grained and has a higher clay content and is, thus, less permeable. It appears that most of the treatment gas was channeled through the higher, more-permeable zone and the lower zone was bypassed. Treatment of the lower zone could probably be accomplished, however, if a second injection well were installed and screened across the zone so that treatment gas could be forced into this interval. The amount of H 2 S consumed during the test exceeded the amount predicted by the laboratory treatability study. In addition, the levels of H 2 S observed at the extraction wells were relatively low, even though a significant level of treatment was observed at the site. It is inferred that interfering reactions or slower reaction kinetics are the likely source of consumption of extra H 2 S observed in the field. Future laboratory work will be undertaken to investigate the nature of these chemical reactions and the reaction rates associated with the gaseous reduction of Cr(VI) in soils. Elucidation of these effects may reveal methods for improving the effectiveness of the technology and reducing unit costs. A life-cycle cost model was developed for the technology based on demonstration information (Hogan 1998). This model suggests that the technology should compare favorably with excavation from a cost basis for larger sites, especially when

Measurement of hydrogen in BCN films by nuclear reaction analysis

Energy Technology Data Exchange (ETDEWEB)

Yasui, Haruyuki; Hirose, Yukio; Sasaki, Toshihiko [Kanazawa Univ. (Japan); Awazu, Kaoru [Industrial Research Inst., of Ishikawa, Kanazawa (Japan); Naramoto, Hiroshi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2001-07-01

Hydrogen is a very common contaminant in carbon films. It can strongly influence on mechanical, physical and chemical properties of the films. The analysis of hydrogen is therefore a crucial problem produce the films with the properties required. Ion beam techniques using nuclear reactions are effective for the quantitative determination of hydrogen concentration. A specially designed spectrometer is employed for the detailed determination of hydrogen concentrations by detecting 4.43MeV {gamma}-rays from the resonant nuclear reactions {sup 1}H({sup 15}N, {alpha}{gamma}){sup 12}C at the 6.385MeV. In this study, the BCN films were formed on silicon substrate by ion beam assisted deposition (IBAD), in which boron and carbon were deposited by electron beam heating of B{sub 4}C solid and nitrogen was supplied by ion implantation simultaneously. The concentrations of hydrogen in BCN films were measured using RNRA. The mechanical properties of BCN films were evaluated using an ultra-micro-hardness tester. It was confirmed that the hardness of BCN films increased with increasing the concentration of hydrogen. (author)

Reaction theories for N* excitations in πN and γN reactions

International Nuclear Information System (INIS)

Lee, T.S.H.

1996-01-01

The importance of developing reaction theories for investigating N* physics is illustrated in an analysis of pion photoproduction on the nucleon. It is shown that the γN ↔ Δ transition amplitudes predicted by the constituent quark model are in agreement with the values extracted from the γN → πN data only when the contributions from the reaction mechanisms calculated using a dynamical approach are taken into account in the analysis

Characterising Complex Enzyme Reaction Data.

Directory of Open Access Journals (Sweden)

Handan Melike Dönertaş

Full Text Available The relationship between enzyme-catalysed reactions and the Enzyme Commission (EC number, the widely accepted classification scheme used to characterise enzyme activity, is complex and with the rapid increase in our knowledge of the reactions catalysed by enzymes needs revisiting. We present a manual and computational analysis to investigate this complexity and found that almost one-third of all known EC numbers are linked to more than one reaction in the secondary reaction databases (e.g., KEGG. Although this complexity is often resolved by defining generic, alternative and partial reactions, we have also found individual EC numbers with more than one reaction catalysing different types of bond changes. This analysis adds a new dimension to our understanding of enzyme function and might be useful for the accurate annotation of the function of enzymes and to study the changes in enzyme function during evolution.

Demonstration of risk-based decision analysis in remedial alternative selection and design

International Nuclear Information System (INIS)

Evans, E.K.; Duffield, G.M.; Massmann, J.W.; Freeze, R.A.; Stephenson, D.E.

1993-01-01

This study demonstrates the use of risk-based decision analysis (Massmann and Freeze 1987a, 1987b) in the selection and design of an engineering alternative for groundwater remediation at a waste site at the Savannah River Site, a US Department of Energy facility in South Carolina. The investigation focuses on the remediation and closure of the H-Area Seepage Basins, an inactive disposal site that formerly received effluent water from a nearby production facility. A previous study by Duffield et al. (1992), which used risk-based decision analysis to screen a number of ground-water remediation alternatives under consideration for this site, indicated that the most attractive remedial option is ground-water extraction by wells coupled with surface water discharge of treated effluent. The aim of the present study is to demonstrate the iterative use of risk-based decision analysis throughout the design of a particular remedial alternative. In this study, we consider the interaction between two episodes of aquifer testing over a 6-year period and the refinement of a remedial extraction well system design. Using a three-dimensional ground-water flow model, this study employs (1) geostatistics and Monte Carlo techniques to simulate hydraulic conductivity as a stochastic process and (2) Bayesian updating and conditional simulation to investigate multiple phases of aquifer testing. In our evaluation of a remedial alternative, we compute probabilistic costs associated with the failure of an alternative to completely capture a simulated contaminant plume. The results of this study demonstrate the utility of risk-based decision analysis as a tool for improving the design of a remedial alternative through the course of phased data collection at a remedial site

Reaction of H2 with O2 in Excited Electronic States: Reaction Pathways and Rate Constants.

Science.gov (United States)

Pelevkin, Alexey V; Loukhovitski, Boris I; Sharipov, Alexander S

2017-12-21

Comprehensive quantum chemical analysis with the use of the multireference state-averaged complete active space self-consistent field approach was carried out to study the reactions of H 2 with O 2 in a 1 Δ g , b 1 Σ g + , c 1 Σ u - , and A' 3 Δ u electronically excited states. The energetically favorable reaction pathways and possible intersystem crossings have been revealed. The energy barriers were refined employing the extended multiconfiguration quasi-degenerate second-order perturbation theory. It has been shown that the interaction of O 2 (a 1 Δ g ) and O 2 (A' 3 Δ u ) with H 2 occurs through the H-abstraction process with relatively low activation barriers that resulted in the formation of the HO 2 molecule in A″ and A' electronic states, respectively. Meanwhile, molecular oxygen in singlet sigma states (b 1 Σ g + and c 1 Σ u - ) was proved to be nonreactive with respect to the molecular hydrogen. Appropriate rate constants for revealed reaction and quenching channels have been estimated using variational transition-state theory including corrections for the tunneling effect, possible nonadiabatic transitions, and anharmonicity of vibrations for transition states and reactants. It was demonstrated that the calculated reaction rate constant for the H 2 + O 2 (a 1 Δ g ) process is in reasonable agreement with known experimental data. The Arrhenius approximations for these processes have been proposed for the temperature range T = 300-3000 K.

Collection of human reaction times and supporting health related data for analysis of cognitive and physical performance

Directory of Open Access Journals (Sweden)

Petr Brůha

2018-04-01

Full Text Available Smoking, excessive drinking, overeating and physical inactivity are well-established risk factors decreasing human physical performance. Moreover, epidemiological work has identified modifiable lifestyle factors, such as poor diet and physical and cognitive inactivity that are associated with the risk of reduced cognitive performance. Definition, collection and annotation of human reaction times and suitable health related data and metadata provides researchers with a necessary source for further analysis of human physical and cognitive performance. The collection of human reaction times and supporting health related data was obtained from two groups comprising together 349 people of all ages - the visitors of the Days of Science and Technology 2016 held on the Pilsen central square and members of the Mensa Czech Republic visiting the neuroinformatics lab at the University of West Bohemia. Each provided dataset contains a complete or partial set of data obtained from the following measurements: hands and legs reaction times, color vision, spirometry, electrocardiography, blood pressure, blood glucose, body proportions and flexibility. It also provides a sufficient set of metadata (age, gender and summary of the participant's current life style and health to allow researchers to perform further analysis. This article has two main aims. The first aim is to provide a well annotated collection of human reaction times and health related data that is suitable for further analysis of lifestyle and human cognitive and physical performance. This data collection is complemented with a preliminarily statistical evaluation. The second aim is to present a procedure of efficient acquisition of human reaction times and supporting health related data in non-lab and lab conditions. Keywords: Reaction time, Health related data, Cognitive and physical performance, Chronic disease, Data acquisition, Data collection, Software for data collection

The browning value changes and spectral analysis on the Maillard reaction product from glucose and methionine model system

Science.gov (United States)

Al-Baarri, A. N.; Legowo, A. M.; Widayat

2018-01-01

D-glucose has been understood to provide the various effect on the reactivity in Maillard reaction resulting in the changes in physical performance of food product. Therefore this research was done to analyse physical appearance of Maillard reaction product made of D-glucose and methionine as a model system. The changes in browning value and spectral analysis model system were determined. The glucose-methionine model system was produced through the heating treatment at 50°C and RH 70% for 24 hours. The data were collected for every three hour using spectrophotometer. As result, browning value was elevated with the increase of heating time and remarkably high if compare to the D-glucose only. Furthermore, the spectral analysis showed that methionine turned the pattern of peak appearance. As conclusion, methionine raised the browning value and changed the pattern of spectral analysis in Maillard reaction model system.

Substrate-Directed Catalytic Selective Chemical Reactions.

Science.gov (United States)

Sawano, Takahiro; Yamamoto, Hisashi

2018-05-04

The development of highly efficient reactions at only the desired position is one of the most important subjects in organic chemistry. Most of the reactions in current organic chemistry are reagent- or catalyst-controlled reactions, and the regio- and stereoselectivity of the reactions are determined by the inherent nature of the reagent or catalyst. In sharp contrast, substrate-directed reaction determines the selectivity of the reactions by the functional group on the substrate and can strictly distinguish sterically and electronically similar multiple reaction sites in the substrate. In this Perspective, three topics of substrate-directed reaction are mainly reviewed: (1) directing group-assisted epoxidation of alkenes, (2) ring-opening reactions of epoxides by various nucleophiles, and (3) catalytic peptide synthesis. Our newly developed synthetic methods with new ligands including hydroxamic acid derived ligands realized not only highly efficient reactions but also pinpointed reactions at the expected position, demonstrating the substrate-directed reaction as a powerful method to achieve the desired regio- and stereoselective functionalization of molecules from different viewpoints of reagent- or catalyst-controlled reactions.

Modeling of uncertainties in biochemical reactions.

Science.gov (United States)

Mišković, Ljubiša; Hatzimanikatis, Vassily

2011-02-01

Mathematical modeling is an indispensable tool for research and development in biotechnology and bioengineering. The formulation of kinetic models of biochemical networks depends on knowledge of the kinetic properties of the enzymes of the individual reactions. However, kinetic data acquired from experimental observations bring along uncertainties due to various experimental conditions and measurement methods. In this contribution, we propose a novel way to model the uncertainty in the enzyme kinetics and to predict quantitatively the responses of metabolic reactions to the changes in enzyme activities under uncertainty. The proposed methodology accounts explicitly for mechanistic properties of enzymes and physico-chemical and thermodynamic constraints, and is based on formalism from systems theory and metabolic control analysis. We achieve this by observing that kinetic responses of metabolic reactions depend: (i) on the distribution of the enzymes among their free form and all reactive states; (ii) on the equilibrium displacements of the overall reaction and that of the individual enzymatic steps; and (iii) on the net fluxes through the enzyme. Relying on this observation, we develop a novel, efficient Monte Carlo sampling procedure to generate all states within a metabolic reaction that satisfy imposed constrains. Thus, we derive the statistics of the expected responses of the metabolic reactions to changes in enzyme levels and activities, in the levels of metabolites, and in the values of the kinetic parameters. We present aspects of the proposed framework through an example of the fundamental three-step reversible enzymatic reaction mechanism. We demonstrate that the equilibrium displacements of the individual enzymatic steps have an important influence on kinetic responses of the enzyme. Furthermore, we derive the conditions that must be satisfied by a reversible three-step enzymatic reaction operating far away from the equilibrium in order to respond to

Effects of alpha-amylase reaction mechanisms on analysis of resistant-starch contents.

Science.gov (United States)

Moore, Samuel A; Ai, Yongfeng; Chang, Fengdan; Jane, Jay-lin

2015-01-22

This study aimed to understand differences in the resistant starch (RS) contents of native and modified starches obtained using two standard methods of RS content analysis: AOAC Method 991.43 and 2002.02. The largest differences were observed in native potato starch, cross-linked wheat distarch phosphate, and high-amylose corn starch stearic-acid complex (RS5) between using AOAC Method 991.43 with Bacillus licheniformis α-amylase (BL) and AOAC Method 2002.02 with porcine pancreatic α-amylase (PPA). To determine possible reasons for these differences, we hydrolyzed raw-starch granules with BL and PPA with equal activity at pH 6.9 and 37°C for up to 84 h and observed the starch granules displayed distinct morphological differences after the hydrolysis. Starches hydrolyzed by BL showed erosion on the surface of the granules; those hydrolyzed by PPA showed pitting on granule surfaces. These results suggested that enzyme reaction mechanisms, including the sizes of the binding sites and the reaction patterns of the two enzymes, contributed to the differences in the RS contents obtained using different methods of RS analysis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Multitarget global sensitivity analysis of n-butanol combustion.

Science.gov (United States)

Zhou, Dingyu D Y; Davis, Michael J; Skodje, Rex T

2013-05-02

A model for the combustion of butanol is studied using a recently developed theoretical method for the systematic improvement of the kinetic mechanism. The butanol mechanism includes 1446 reactions, and we demonstrate that it is straightforward and computationally feasible to implement a full global sensitivity analysis incorporating all the reactions. In addition, we extend our previous analysis of ignition-delay targets to include species targets. The combination of species and ignition targets leads to multitarget global sensitivity analysis, which allows for a more complete mechanism validation procedure than we previously implemented. The inclusion of species sensitivity analysis allows for a direct comparison between reaction pathway analysis and global sensitivity analysis.

Synthesis by the Pechini method and reaction combustion for the preparation of TiO2: a comparative analysis

International Nuclear Information System (INIS)

Almeida, E.P.; Ribeiro, P.C.; Freitas, N.L.; Lira, H.L.; Costa, A.C.F.M. da; Kiminami, R.H.G.A.

2009-01-01

The aim of this work is to prepare TiO 2 powder by Pechini and combustion reaction methods. A comparative analysis between the structural and morphological results obtained by the two methods was investigated. The powders were characterized by X-ray diffractions (XRD), infrared analysis, nitrogen adsorption (BET) and particle size distribution. The results from XRD show that the powders prepared by Pechini method and by combustion reaction using aniline as fuel, present anatase as major phase and traces of rutile phase. The values of crystallite size and surface area from BET were: 30 e 44 nm; 6.2 e 4.4 m 2 /g, for the powders prepared by Pechini and combustion reaction, respectively. The values of particle size were: 21.9 e 5.3 μm, for the powders prepared by Pechini and combustion reaction, respectively. The Pechini method was more suitable to obtain powders with irregular agglomerates, in the block shape with particles bonded softly and small crystallite size. (author)

Simultaneous demonstration of gelatinolytic activity, morphology, and immunohistochemical reaction using zymography film.

Science.gov (United States)

Kanomata, Naoki; Hasebe, Takahiro; Moriya, Takuya; Ochiai, Atsushi

2013-12-01

In situ zymography has been used to assess gelatinolytic activity, which is mainly due to matrix metalloproteinases (MMPs) in cancer tissues. MMPs play an important role in cancer invasion and metastasis. Film in situ zymography (FIZ) enables the in situ evaluation of gelatinolytic activity with high reproducibility. In this article, we report a study of FIZ, in a case of breast cancer with an invasive carcinoma component showing clear gelatinolytic activity, and in a non-invasive carcinoma component showing little gelatinolytic activity. Immunohistochemistry on FIZ was also performed. The simultaneous detection of gelatinolytic activity and immunohistochemical reaction was established in a single film. Immunohistochemistry on FIZ may have good potential for the investigation of cancer microenvironment.

Coating of graphite flakes with MgO/carbon nanocomposite via gas state reaction

International Nuclear Information System (INIS)

Sharif, M.; Faghihi-Sani, M.A.; Golestani-Fard, F.; Saberi, A.; Soltani, Ali Khalife

2010-01-01

Coating of graphite flakes with MgO/carbon nanocomposite was carried out via gaseous state reaction between mixture of Mg metal, CO gas and graphite flakes at 1000 o C. XRD and FE-SEM analysis of coating showed that the coating was comprised of MgO nano particles and amorphous carbon distributed smoothly and covered the graphite surface evenly. Thermodynamic calculations were employed to predict the reaction sequences as well as phase stability. The effect of coating on water wettability and oxidation resistance of graphite was studied using contact angle measurement and TG analysis, respectively. It was demonstrated that the reaction between Mg and CO could result in MgO/C nanocomposite deposition. The coating improved water wettability of graphite and also enhanced the oxidation resistance of graphite flakes significantly. Also the graphite coating showed significant phenolic resin-wettabilty owing to high surface area of such hydrophilic nano composite coating. The importance of graphite coating is explained with emphasis on its potential application in graphite containing refractories.

Wang-Landau Reaction Ensemble Method: Simulation of Weak Polyelectrolytes and General Acid-Base Reactions.

Science.gov (United States)

Landsgesell, Jonas; Holm, Christian; Smiatek, Jens

2017-02-14

We present a novel method for the study of weak polyelectrolytes and general acid-base reactions in molecular dynamics and Monte Carlo simulations. The approach combines the advantages of the reaction ensemble and the Wang-Landau sampling method. Deprotonation and protonation reactions are simulated explicitly with the help of the reaction ensemble method, while the accurate sampling of the corresponding phase space is achieved by the Wang-Landau approach. The combination of both techniques provides a sufficient statistical accuracy such that meaningful estimates for the density of states and the partition sum can be obtained. With regard to these estimates, several thermodynamic observables like the heat capacity or reaction free energies can be calculated. We demonstrate that the computation times for the calculation of titration curves with a high statistical accuracy can be significantly decreased when compared to the original reaction ensemble method. The applicability of our approach is validated by the study of weak polyelectrolytes and their thermodynamic properties.

Reaction kinetics of polybutylene terephthalate polycondensation reaction

NARCIS (Netherlands)

Darda, P. J.; Hogendoorn, J. A.; Versteeg, G. F.; Souren, F.

2005-01-01

The kinetics of the forward polycondensation reaction of polybutylene terephthalate (PBT) has been investigated using thermogravimetric analysis (TGA). PBT - prepolymer with an initial degree of polymerization of 5.5 was used as starting material. The PBT prepolymer was prepared from dimethyl

Component Analysis of Sweet BV and Clinical Trial on Antibody Titer and Allergic Reactions

Directory of Open Access Journals (Sweden)

Ki Rok, Kwon

2006-06-01

Full Text Available Objectives : The aim of this study was to observe prevention of allergic reactions of Sweet Bee Venom (removing enzyme components from Bee Venom. Methods : Content analysis of Sweet Bee Venom and Bee Venom was rendered using HPLC method and characterization of Anti-Sweet Bee Venom in Rabbit Serum. Clinical observation was conducted for inducement of allergic responses to Sweet BV. Results : 1. Analyzing melittin content using HPLC, Sweet BV contained 34.9% more melittin than Bee venom pharmacopuncture at same concentration. 2. Observing chromatogram of HPLC, removal of the enzyme was successfully rendered on Sweet BV. 3. The anti-serum of Sweet BV showed high titers against melittin and bee venom and relatively low titer against phospholipase A2. 4. After conducting approximately 3,000 cases of Sweet BV administration, not a single case of generalized anaphylatic reaction occurred in clinical observation. 5. Mild compared to the bee venom pharmacopuncture, Sweet BV showed some acute hypersensitive reactions of edema, itchiness, and aching locally. 6. Sweet BV was administered on six patients with previous history of suffering from generalized acute hypersensitive reactions with the bee venom. None of the patients showed allergic reactions with Sweet BV, suggesting it can effectively prevent anaphylatic shock which may occur after the bee venom pharmacopuncture procedure. Conclusion : Summarizing above results, Sweet Bee Venom appears to be an effective measurement against allergic reactions from the bee venom pharmacopuncture especially against anaphylatic shock.

An integrated high temperature environmental cell for atom probe tomography studies of gas-surface reactions: Instrumentation and results

International Nuclear Information System (INIS)

Dumpala, S.; Broderick, S.R.; Bagot, P.A.J.; Rajan, K.

2014-01-01

An integrated environmental cell has been designed and developed for the latest generation of Atom Probe Tomography LEAP™ instruments, allowing controlled exposure of samples to gases at high temperatures. Following treatment, samples can be transferred through the LEAP vacuum system for subsequent APT analysis, which provides detailed information on changes to chemical microstructures following the reactions with near-atomic resolution. A full description of the cell is presented, along with some sample results on the oxidation of aluminum and two platinum-group alloys, demonstrating the capability of combining exposure/characterization functionality in a single instrument. - Highlights: • Designed and built atom probe environmental cell for in situ reactions. • Investigated Al oxidation, and demonstrated improvement with new cell. • in situ APT analysis of Pt-alloys showed surface segregation of Rh and Ir

Biomass pyrolysis and combustion integral and differential reaction heats with temperatures using thermogravimetric analysis/differential scanning calorimetry.

Science.gov (United States)

Shen, Jiacheng; Igathinathane, C; Yu, Manlu; Pothula, Anand Kumar

2015-06-01

Integral reaction heats of switchgrass, big bluestem, and corn stalks were determined using thermogravimetric analysis/differential scanning calorimetry (TGA/DSC). Iso-conversion differential reaction heats using TGA/DSC pyrolysis and combustion of biomass were not available, despite reports available on heats required and released. A concept of iso-conversion differential reaction heats was used to determine the differential reaction heats of each thermal characteristics segment of these materials. Results showed that the integral reaction heats were endothermic from 30 to 700°C for pyrolysis of switchgrass and big bluestem, but they were exothermic for corn stalks prior to 587°C. However, the integral reaction heats for combustion of the materials followed an endothermic to exothermic transition. The differential reaction heats of switchgrass pyrolysis were predominantly endothermic in the fraction of mass loss (0.0536-0.975), and were exothermic for corn stalks (0.0885-0.850) and big bluestem (0.736-0.919). Study results provided better insight into biomass thermal mechanism. Published by Elsevier Ltd.

Hydrogen incorporation and radiation induced dynamics in metal-oxide-silicon structures. A study using nuclear reaction analysis

International Nuclear Information System (INIS)

Briere, M.A.

1993-07-01

Resonant nuclear reaction analysis, using the 1 H( 15 N, αγ) 12 C reaction at 6.4 MeV, has been successfully applied to the investigation of hydrogen incorporation and radiation induced migration in metal-oxide-silicon structures. A preliminary study of the influence of processing parameters on the H content of thermal oxides, with and without gate material present, has been performed. It is found that the dominant source of hydrogen in Al gate devices and dry oxides is often contamination, likely in the form of adsorbed water vapor, formed upon exposure to room air after removal from the oxidation furnace. Concentrations of hydrogen in the bulk oxide as high as 3 10 20 cm -3 (Al gate), and as low as 1 10 18 cm -3 (poly Si-gate) have been observed. Hydrogen accumulation at the Si-SiO 2 interface has been reproducibly demonstrated for as-oxidized samples, as well as for oxides exposed to H 2 containing atmospheres during subsequent thermal processing. The migration of hydrogen, from the bulk oxide to the silicon-oxide interface during NRA, has been observed and intensively investigated. A direct correlation between the hydrogen content of the bulk oxide and the radiation generated oxide charges and interface states is presented. These data provide strong support for the important role of hydrogen in determining the radiation sensitivity of electronic devices. (orig.)

Continuous protein concentration via free-flow moving reaction boundary electrophoresis.

Science.gov (United States)

Kong, Fanzhi; Zhang, Min; Chen, Jingjing; Fan, Liuyin; Xiao, Hua; Liu, Shaorong; Cao, Chengxi

2017-07-28

In this work, we developed the model and theory of free-flow moving reaction boundary electrophoresis (FFMRB) for continuous protein concentration for the first time. The theoretical results indicated that (i) the moving reaction boundary (MRB) can be quantitatively designed in free-flow electrophoresis (FFE) system; (ii) charge-to-mass ratio (Z/M) analysis could provide guidance for protein concentration optimization; and (iii) the maximum processing capacity could be predicted. To demonstrate the model and theory, three model proteins of hemoglobin (Hb), cytochrome C (Cyt C) and C-phycocyanin (C-PC) were chosen for the experiments. The experimental results verified that (i) stable MRBs with different velocities could be established in FFE apparatus with weak acid/weak base neutralization reaction system; (ii) proteins of Hb, Cyt C and C-PC were well concentrated with FFMRB; and (iii) a maximum processing capacity and recovery ratio of Cyt C enrichment were 126mL/h and 95.5% respectively, and a maximum enrichment factor was achieved 12.6 times for Hb. All of the experiments demonstrated the protein concentration model and theory. In contrast to other methods, the continuous processing ability enables FFMRB to efficiently enrich diluted protein or peptide in large volume solution. Copyright © 2017 Elsevier B.V. All rights reserved.

Performance Demonstration Program Plan for RCRA Constituent Analysis of Solidified Wastes

International Nuclear Information System (INIS)

2006-01-01

The Performance Demonstration Program (PDP) for Resource Conservation and Recovery Act (RCRA) constituents distributes test samples for analysis of volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), and metals in solid matrices. Each distribution of test samples is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements performed for transuranic (TRU) waste characterization. The primary documents governing the conduct of the PDP are the Quality Assurance Program Document (QAPD; DOE/CBFO-94-1012) and the Waste Isolation Pilot Plant (WIPP) Waste Analysis Plan (WAP) contained in the Hazardous Waste Facility Permit (NM4890139088-TSDF) issued by the New Mexico Environment Department. The WAP requires participation in the PDP; the PDP must comply with the QAPD and the WAP. This plan implements the general requirements of the QAPD and the applicable requirements of the WAP for the RCRA PDP. Participating laboratories demonstrate acceptable performance by successfully analyzing single-blind performance evaluation samples (subsequently referred to as PDP samples) according to the criteria established in this plan. PDP samples are used as an independent means to assess laboratory performance regarding compliance with the WAP quality assurance objectives (QAOs). The concentrations of analytes in the PDP samples address levels of regulatory concern and encompass the range of concentrations anticipated in waste characterization samples. The WIPP requires analyses of homogeneous solid wastes to demonstrate compliance with regulatory requirements. These analyses must be performed by laboratories that demonstrate acceptable performance in this PDP. These analyses are referred to as WIPP analyses, and the samples on which they are performed are referred to as WIPP samples. Participating laboratories must analyze PDP samples using the same procedures used for WIPP samples.

Catalyst Initiation in the Oscillatory Carbonylation Reaction

Directory of Open Access Journals (Sweden)

Katarina Novakovic

2011-01-01

Full Text Available Palladium(II iodide is used as a catalyst in the phenylacetylene oxidative carbonylation reaction that has demonstrated oscillatory behaviour in both pH and heat of reaction. In an attempt to extract the reaction network responsible for the oscillatory nature of this reaction, the system was divided into smaller parts and they were studied. This paper focuses on understanding the reaction network responsible for the initial reactions of palladium(II iodide within this oscillatory reaction. The species researched include methanol, palladium(II iodide, potassium iodide, and carbon monoxide. Several chemical reactions were considered and applied in a modelling study. The study revealed the significant role played by traces of water contained in the standard HPLC grade methanol used.

Two reactions method for accurate analysis by irradiation with charged particles

International Nuclear Information System (INIS)

Ishii, K.; Sastri, C.S.; Valladon, M.; Borderie, B.; Debrun, J.L.

1978-01-01

In the average stopping power method the formula error itself was negligible but systematic errors could be introduced by the stopping power data used in this formula. A method directly derived from the average stopping power method, but based on the use of two nuclear reactions, is described here. This method has a negligible formula error and does not require the use of any stopping power or range data: accurate and 'self-consistent' analysis by irradiation with charged particles is then possible. (Auth.)

Global sensitivity analysis in stochastic simulators of uncertain reaction networks.

Science.gov (United States)

Navarro Jimenez, M; Le Maître, O P; Knio, O M

2016-12-28

Stochastic models of chemical systems are often subjected to uncertainties in kinetic parameters in addition to the inherent random nature of their dynamics. Uncertainty quantification in such systems is generally achieved by means of sensitivity analyses in which one characterizes the variability with the uncertain kinetic parameters of the first statistical moments of model predictions. In this work, we propose an original global sensitivity analysis method where the parametric and inherent variability sources are both treated through Sobol's decomposition of the variance into contributions from arbitrary subset of uncertain parameters and stochastic reaction channels. The conceptual development only assumes that the inherent and parametric sources are independent, and considers the Poisson processes in the random-time-change representation of the state dynamics as the fundamental objects governing the inherent stochasticity. A sampling algorithm is proposed to perform the global sensitivity analysis, and to estimate the partial variances and sensitivity indices characterizing the importance of the various sources of variability and their interactions. The birth-death and Schlögl models are used to illustrate both the implementation of the algorithm and the richness of the proposed analysis method. The output of the proposed sensitivity analysis is also contrasted with a local derivative-based sensitivity analysis method classically used for this type of systems.

Global sensitivity analysis in stochastic simulators of uncertain reaction networks

KAUST Repository

Navarro, María

2016-12-26

Stochastic models of chemical systems are often subjected to uncertainties in kinetic parameters in addition to the inherent random nature of their dynamics. Uncertainty quantification in such systems is generally achieved by means of sensitivity analyses in which one characterizes the variability with the uncertain kinetic parameters of the first statistical moments of model predictions. In this work, we propose an original global sensitivity analysis method where the parametric and inherent variability sources are both treated through Sobol’s decomposition of the variance into contributions from arbitrary subset of uncertain parameters and stochastic reaction channels. The conceptual development only assumes that the inherent and parametric sources are independent, and considers the Poisson processes in the random-time-change representation of the state dynamics as the fundamental objects governing the inherent stochasticity. A sampling algorithm is proposed to perform the global sensitivity analysis, and to estimate the partial variances and sensitivity indices characterizing the importance of the various sources of variability and their interactions. The birth-death and Schlögl models are used to illustrate both the implementation of the algorithm and the richness of the proposed analysis method. The output of the proposed sensitivity analysis is also contrasted with a local derivative-based sensitivity analysis method classically used for this type of systems.

Modular verification of chemical reaction network encodings via serializability analysis

Science.gov (United States)

Lakin, Matthew R.; Stefanovic, Darko; Phillips, Andrew

2015-01-01

Chemical reaction networks are a powerful means of specifying the intended behaviour of synthetic biochemical systems. A high-level formal specification, expressed as a chemical reaction network, may be compiled into a lower-level encoding, which can be directly implemented in wet chemistry and may itself be expressed as a chemical reaction network. Here we present conditions under which a lower-level encoding correctly emulates the sequential dynamics of a high-level chemical reaction network. We require that encodings are transactional, such that their execution is divided by a “commit reaction” that irreversibly separates the reactant-consuming phase of the encoding from the product-generating phase. We also impose restrictions on the sharing of species between reaction encodings, based on a notion of “extra tolerance”, which defines species that may be shared between encodings without enabling unwanted reactions. Our notion of correctness is serializability of interleaved reaction encodings, and if all reaction encodings satisfy our correctness properties then we can infer that the global dynamics of the system are correct. This allows us to infer correctness of any system constructed using verified encodings. As an example, we show how this approach may be used to verify two- and four-domain DNA strand displacement encodings of chemical reaction networks, and we generalize our result to the limit where the populations of helper species are unlimited. PMID:27325906

Optimizing Chemical Reactions with Deep Reinforcement Learning.

Science.gov (United States)

Zhou, Zhenpeng; Li, Xiaocheng; Zare, Richard N

2017-12-27

Deep reinforcement learning was employed to optimize chemical reactions. Our model iteratively records the results of a chemical reaction and chooses new experimental conditions to improve the reaction outcome. This model outperformed a state-of-the-art blackbox optimization algorithm by using 71% fewer steps on both simulations and real reactions. Furthermore, we introduced an efficient exploration strategy by drawing the reaction conditions from certain probability distributions, which resulted in an improvement on regret from 0.062 to 0.039 compared with a deterministic policy. Combining the efficient exploration policy with accelerated microdroplet reactions, optimal reaction conditions were determined in 30 min for the four reactions considered, and a better understanding of the factors that control microdroplet reactions was reached. Moreover, our model showed a better performance after training on reactions with similar or even dissimilar underlying mechanisms, which demonstrates its learning ability.

PIERO ontology for analysis of biochemical transformations: effective implementation of reaction information in the IUBMB enzyme list.

Science.gov (United States)

Kotera, Masaaki; Nishimura, Yosuke; Nakagawa, Zen-ichi; Muto, Ai; Moriya, Yuki; Okamoto, Shinobu; Kawashima, Shuichi; Katayama, Toshiaki; Tokimatsu, Toshiaki; Kanehisa, Minoru; Goto, Susumu

2014-12-01

Genomics is faced with the issue of many partially annotated putative enzyme-encoding genes for which activities have not yet been verified, while metabolomics is faced with the issue of many putative enzyme reactions for which full equations have not been verified. Knowledge of enzymes has been collected by IUBMB, and has been made public as the Enzyme List. To date, however, the terminology of the Enzyme List has not been assessed comprehensively by bioinformatics studies. Instead, most of the bioinformatics studies simply use the identifiers of the enzymes, i.e. the Enzyme Commission (EC) numbers. We investigated the actual usage of terminology throughout the Enzyme List, and demonstrated that the partial characteristics of reactions cannot be retrieved by simply using EC numbers. Thus, we developed a novel ontology, named PIERO, for annotating biochemical transformations as follows. First, the terminology describing enzymatic reactions was retrieved from the Enzyme List, and was grouped into those related to overall reactions and biochemical transformations. Consequently, these terms were mapped onto the actual transformations taken from enzymatic reaction equations. This ontology was linked to Gene Ontology (GO) and EC numbers, allowing the extraction of common partial reaction characteristics from given sets of orthologous genes and the elucidation of possible enzymes from the given transformations. Further future development of the PIERO ontology should enhance the Enzyme List to promote the integration of genomics and metabolomics.

Perspective: Chemical reactions in ionic liquids monitored through the gas (vacuum)/liquid interface.

Science.gov (United States)

Maier, F; Niedermaier, I; Steinrück, H-P

2017-05-07

This perspective analyzes the potential of X-ray photoelectron spectroscopy under ultrahigh vacuum (UHV) conditions to follow chemical reactions in ionic liquids in situ. Traditionally, only reactions occurring on solid surfaces were investigated by X-ray photoelectron spectroscopy (XPS) in situ. This was due to the high vapor pressures of common liquids or solvents, which are not compatible with the required UHV conditions. It was only recently realized that the situation is very different when studying reactions in Ionic Liquids (ILs), which have an inherently low vapor pressure, and first studies have been performed within the last years. Compared to classical spectroscopy techniques used to monitor chemical reactions, the advantage of XPS is that through the analysis of their core levels all relevant elements can be quantified and their chemical state can be analyzed under well-defined (ultraclean) conditions. In this perspective, we cover six very different reactions which occur in the IL, with the IL, or at an IL/support interface, demonstrating the outstanding potential of in situ XPS to gain insights into liquid phase reactions in the near-surface region.

Safety analysis report for packaging (onsite) transuranic performance demonstration program sample packaging

International Nuclear Information System (INIS)

Mccoy, J.C.

1997-01-01

The Transuranic Performance Demonstration Program (TPDP) sample packaging is used to transport highway route controlled quantities of weapons grade (WG) plutonium samples from the Plutonium Finishing Plant (PFP) to the Waste Receiving and Processing (WRAP) facility and back. The purpose of these shipments is to test the nondestructive assay equipment in the WRAP facility as part of the Nondestructive Waste Assay PDP. The PDP is part of the U. S. Department of Energy (DOE) National TRU Program managed by the U. S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico. Details of this program are found in CAO-94-1045, Performance Demonstration Program Plan for Nondestructive Assay for the TRU Waste Characterization Program (CAO 1994); INEL-96/0129, Design of Benign Matrix Drums for the Non-Destructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996a); and INEL-96/0245, Design of Phase 1 Radioactive Working Reference Materials for the Nondestructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996b). Other program documentation is maintained by the national TRU program and each DOE site participating in the program. This safety analysis report for packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the TRU PDP sample packaging meets the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for an onsite Transportation Hazard Indicator (THI) 2 packaging. This SARP, however, does not include evaluation of any operations within the PFP or WRAP facilities, including handling, maintenance, storage, or operating requirements, except as they apply directly to transportation between the gate of PFP and the gate of the WRAP facility. All other activities are subject to the requirements of the facility safety analysis reports (FSAR) of the PFP or WRAP facility and requirements of the PDP

Theoretical analysis of consecutive reactions in adiabatic stirred tank reactors

International Nuclear Information System (INIS)

Jo, Byung Wook; Kim, Sun Il; Hong, Won Hae; Cha, Wol Suk; Kim, Soong Pyung; Kim, Jung Gyu

1990-01-01

By mathematical model for the case of the consecutive first-order exothermic reaction in an adiabatic CSTR, the effects of the system parameter i. e. relative residence time, heat of reaction and thermal sensitivity of reaction rate constant, on the concentration profile of the intermediate product of a consecutive reaction were obtained as follows. For fixed values of the ratio of the reaction rate constants t 1 / t 2 , the ratio of the correponding system parameter α where α>1 and the sensitivities of the reaction rate constants S1 and S2, the maximum value of the intermediate production dimensionless concentration increases with increase in the values of the relative energy parameter E1 and E2 and it decreases with a decrease in E1 and E2. For fixed values of the ratio of the reaction rate constants t 1 / t 2 , the ratio of the corresponding system parameter α where α 1 and t 2 and it increases with a decrease in S1 and S2. For fixed values of the ratio of the reaction rate constants t 1 / t 2 , the ratio of the corresponding system parameters α where α=1 and the relative energy parameters E1 and E2, the maximum value of the intermediate product dimensionless is constant with either increase or decrease in the sensitivities of the reaction rate constants S1 and S2. (Author)

Experimental and numerical analysis of the combustor for a cogeneration system based on the aluminum/water reaction

International Nuclear Information System (INIS)

Milani, Massimo; Montorsi, Luca; Paltrinieri, Fabrizio; Stefani, Matteo

2014-01-01

Highlights: • Aluminum reaction with water is studied as a technology for hydrogen production. • A test rig is developed for the analysis of aluminum/water reaction. • The system is the core component of a cogeneration plant for hydrogen/power production. • The interaction of liquid aluminum jet and water steam stream is investigated. • The main capabilities of the injection system are assessed. - Abstract: The paper focuses on the design of the experimental apparatus aimed at analyzing the performance of the combustion chamber of a cogeneration system based on the reaction of liquid aluminum and water steam. The cogeneration system exploits the heat released by the oxidation of aluminum with water for super-heating the vapor of a steam cycle and simultaneously producing hydrogen. The only by-product is alumina, which in a closed loop can be recycled back and transformed again into aluminum. Therefore, aluminum is used as an energy carrier to transport the energy from the alumina reduction plant to the location of the proposed system. The water is also used in a closed loop since the amount of water produced employing the hydrogen obtained by the proposed system corresponds to the oxidizing water for the Al/H 2 O reaction. This study investigates the combustor where the liquid aluminum–steam reaction takes place. In particular, the design of the combustion chamber and the interaction between the liquid aluminum jet and the water steam flow are evaluated using a numerical and an experimental approach. The test rig is specifically designed for the analysis of the liquid aluminum injection in a slightly super-heated steam stream. The first experiments are carried out to verify the correct behavior of the test rig. Thermography is employed to qualitatively assess the steam entrainment of the liquid aluminum jet. Finally, the experimental measurements are compared with the multi-dimension multi-phase flow simulations in order to estimate the influence of

Humidity independent mass spectrometry for gas phase chemical analysis via ambient proton transfer reaction.

Science.gov (United States)

Zhu, Hongying; Huang, Guangming

2015-03-31

In this work, a humidity independent mass spectrometric method was developed for rapid analysis of gas phase chemicals. This method is based upon ambient proton transfer reaction between gas phase chemicals and charged water droplets, in a reaction chamber with nearly saturate humidity under atmospheric pressure. The humidity independent nature enables direct and rapid analysis of raw gas phase samples, avoiding time- and sample-consuming sample pretreatments in conventional mass spectrometry methods to control sample humidity. Acetone, benzene, toluene, ethylbenzene and meta-xylene were used to evaluate the analytical performance of present method. The limits of detection for benzene, toluene, ethylbenzene and meta-xylene are in the range of ∼0.1 to ∼0.3 ppbV; that of benzene is well below the present European Union permissible exposure limit for benzene vapor (5 μg m(-3), ∼1.44 ppbV), with linear ranges of approximately two orders of magnitude. The majority of the homemade device contains a stainless steel tube as reaction chamber and an ultrasonic humidifier as the source of charged water droplets, which makes this cheap device easy to assemble and facile to operate. In addition, potential application of this method was illustrated by the real time identification of raw gas phase chemicals released from plants at different physiological stages. Copyright © 2015 Elsevier B.V. All rights reserved.

Exploiting Fission Chain Reaction Dynamics to Image Fissile Materials

Science.gov (United States)

Chapman, Peter Henry

Radiation imaging is one potential method to verify nuclear weapons dismantlement. The neutron coded aperture imager (NCAI), jointly developed by Oak Ridge National Laboratory (ORNL) and Sandia National Laboratories (SNL), is capable of imaging sources of fast (e.g., fission spectrum) neutrons using an array of organic scintillators. This work presents a method developed to discriminate between non-multiplying (i.e., non-fissile) neutron sources and multiplying (i.e., fissile) neutron sources using the NCAI. This method exploits the dynamics of fission chain-reactions; it applies time-correlated pulse-height (TCPH) analysis to identify neutrons in fission chain reactions. TCPH analyzes the neutron energy deposited in the organic scintillator vs. the apparent neutron time-of-flight. Energy deposition is estimated from light output, and time-of-flight is estimated from the time between the neutron interaction and the immediately preceding gamma interaction. Neutrons that deposit more energy than can be accounted for by their apparent time-of-flight are identified as fission chain-reaction neutrons, and the image is reconstructed using only these neutron detection events. This analysis was applied to measurements of weapons-grade plutonium (WGPu) metal and 252Cf performed at the Nevada National Security Site (NNSS) Device Assembly Facility (DAF) in July 2015. The results demonstrate it is possible to eliminate the non-fissile 252Cf source from the image while preserving the fissileWGPu source. TCPH analysis was also applied to additional scenes in which theWGPu and 252Cf sources were measured individually. The results of these separate measurements further demonstrate the ability to remove the non-fissile 252Cf source and retain the fissileWGPu source. Simulations performed using MCNPX-PoliMi indicate that in a one hour measurement, solid spheres ofWGPu are retained at a 1sigma level for neutron multiplications M -˜ 3.0 and above, while hollowWGPu spheres are

Advanced Reactor Passive System Reliability Demonstration Analysis for an External Event

Directory of Open Access Journals (Sweden)

Matthew Bucknor

2017-03-01

Full Text Available Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general for the postulated transient event.

Advanced reactor passive system reliability demonstration analysis for an external event

Energy Technology Data Exchange (ETDEWEB)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia J.; Grelle, Austin [Argonne National Laboratory, Argonne (United States)

2017-03-15

Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general) for the postulated transient event.

Advanced reactor passive system reliability demonstration analysis for an external event

International Nuclear Information System (INIS)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia J.; Grelle, Austin

2017-01-01

Many advanced reactor designs rely on passive systems to fulfill safety functions during accident sequences. These systems depend heavily on boundary conditions to induce a motive force, meaning the system can fail to operate as intended because of deviations in boundary conditions, rather than as the result of physical failures. Furthermore, passive systems may operate in intermediate or degraded modes. These factors make passive system operation difficult to characterize within a traditional probabilistic framework that only recognizes discrete operating modes and does not allow for the explicit consideration of time-dependent boundary conditions. Argonne National Laboratory has been examining various methodologies for assessing passive system reliability within a probabilistic risk assessment for a station blackout event at an advanced small modular reactor. This paper provides an overview of a passive system reliability demonstration analysis for an external event. Considering an earthquake with the possibility of site flooding, the analysis focuses on the behavior of the passive Reactor Cavity Cooling System following potential physical damage and system flooding. The assessment approach seeks to combine mechanistic and simulation-based methods to leverage the benefits of the simulation-based approach without the need to substantially deviate from conventional probabilistic risk assessment techniques. Although this study is presented as only an example analysis, the results appear to demonstrate a high level of reliability of the Reactor Cavity Cooling System (and the reactor system in general) for the postulated transient event

In Situ Gaseous Reduction Pilot Demonstration - Final Report

Energy Technology Data Exchange (ETDEWEB)

Thornton, E.C.; Phelan, J.M.; Giblin, J.T.; Olsen, K.B.; Miller, R.D.; Gilmore, T.J.

1999-02-23

The demonstration of the IGRS approach conducted at SWMU 143 on the White Sands Missile Range has provided information needed to complete a technical performance assessment and cost analysis of the technology. At least 70% of the Cr(VI) present in contaminated sediment at the site was reduced, thus verifying the effectiveness of the approach. Most of the treatment occurred in a zone located from {approximately}4 to 10 ft below ground surface, which appears to be a higher permeability interval. A deeper zone from {approximately}10 to 16 ft that contains lower levels of contamination was essentially unaffected. The deeper zone is somewhat finer grained and has a higher clay content and is, thus, less permeable. It appears that most of the treatment gas was channeled through the higher, more-permeable zone and the lower zone was bypassed. Treatment of the lower zone could probably be accomplished, however, if a second injection well were installed and screened across the zone so that treatment gas could be forced into this interval. The amount of H{sub 2}S consumed during the test exceeded the amount predicted by the laboratory treatability study. In addition, the levels of H{sub 2}S observed at the extraction wells were relatively low, even though a significant level of treatment was observed at the site. It is inferred that interfering reactions or slower reaction kinetics are the likely source of consumption of extra H{sub 2}S observed in the field. Future laboratory work will be undertaken to investigate the nature of these chemical reactions and the reaction rates associated with the gaseous reduction of Cr(VI) in soils. Elucidation of these effects may reveal methods for improving the effectiveness of the technology and reducing unit costs. A life-cycle cost model was developed for the technology based on demonstration information (Hogan 1998). This model suggests that the technology should compare favorably with excavation from a cost basis for larger sites

Development of fast reactor containment safety analysis code, CONTAIN-LMR. (3) Improvement of sodium-concrete reaction model

International Nuclear Information System (INIS)

Kawaguchi, Munemichi; Doi, Daisuke; Seino, Hiroshi; Miyahara, Shinya

2015-01-01

A computer code, CONTAIN-LMR, is an integrated analysis tool to predict the consequence of severe accident in a liquid metal fast reactor. Because a sodium-concrete reaction behavior is one of the most important phenomena in the accident, a Sodium-Limestone Concrete Ablation Model (SLAM) has been developed and installed into the original CONTAIN code at Sandia National Laboratories (SNL) in the U.S. The SLAM treats chemical reaction kinetics between the sodium and the concrete compositions mechanistically using a three-region model, containing a pool (sodium and reaction debris) region, a dry (boundary layer (B/L) and dehydrated concrete) region, and a wet (hydrated concrete) region, the application is limited to the reaction between sodium and limestone concrete. In order to apply SLAM to the reaction between sodium and siliceous concrete which is an ordinary structural concrete in Japan, the chemical reaction kinetics model has been improved to consider the new chemical reactions between sodium and silicon dioxide. The improved model was validated to analyze a series of sodium-concrete experiments which were conducted in Japan Atomic Energy Agency (JAEA). It has been found that relatively good agreement between calculation and experimental results is obtained and the CONTAIN-LMR code has been validated with regard to the sodium-concrete reaction phenomena. (author)

MONITORING POTENTIAL DRUG INTERACTIONS AND REACTIONS VIA NETWORK ANALYSIS OF INSTAGRAM USER TIMELINES

Science.gov (United States)

CORREIA, RION BRATTIG; LI, LANG; ROCHA, LUIS M.

2015-01-01

Much recent research aims to identify evidence for Drug-Drug Interactions (DDI) and Adverse Drug reactions (ADR) from the biomedical scientific literature. In addition to this “Bibliome”, the universe of social media provides a very promising source of large-scale data that can help identify DDI and ADR in ways that have not been hitherto possible. Given the large number of users, analysis of social media data may be useful to identify under-reported, population-level pathology associated with DDI, thus further contributing to improvements in population health. Moreover, tapping into this data allows us to infer drug interactions with natural products—including cannabis—which constitute an array of DDI very poorly explored by biomedical research thus far. Our goal is to determine the potential of Instagram for public health monitoring and surveillance for DDI, ADR, and behavioral pathology at large. Most social media analysis focuses on Twitter and Facebook, but Instagram is an increasingly important platform, especially among teens, with unrestricted access of public posts, high availability of posts with geolocation coordinates, and images to supplement textual analysis. Using drug, symptom, and natural product dictionaries for identification of the various types of DDI and ADR evidence, we have collected close to 7000 user timelines spanning from October 2010 to June 2015. We report on 1) the development of a monitoring tool to easily observe user-level timelines associated with drug and symptom terms of interest, and 2) population-level behavior via the analysis of co-occurrence networks computed from user timelines at three different scales: monthly, weekly, and daily occurrences. Analysis of these networks further reveals 3) drug and symptom direct and indirect associations with greater support in user timelines, as well as 4) clusters of symptoms and drugs revealed by the collective behavior of the observed population. This demonstrates that

Analysis of reaction schemes using maximum rates of constituent steps

Science.gov (United States)

Motagamwala, Ali Hussain; Dumesic, James A.

2016-01-01

We show that the steady-state kinetics of a chemical reaction can be analyzed analytically in terms of proposed reaction schemes composed of series of steps with stoichiometric numbers equal to unity by calculating the maximum rates of the constituent steps, rmax,i, assuming that all of the remaining steps are quasi-equilibrated. Analytical expressions can be derived in terms of rmax,i to calculate degrees of rate control for each step to determine the extent to which each step controls the rate of the overall stoichiometric reaction. The values of rmax,i can be used to predict the rate of the overall stoichiometric reaction, making it possible to estimate the observed reaction kinetics. This approach can be used for catalytic reactions to identify transition states and adsorbed species that are important in controlling catalyst performance, such that detailed calculations using electronic structure calculations (e.g., density functional theory) can be carried out for these species, whereas more approximate methods (e.g., scaling relations) are used for the remaining species. This approach to assess the feasibility of proposed reaction schemes is exact for reaction schemes where the stoichiometric coefficients of the constituent steps are equal to unity and the most abundant adsorbed species are in quasi-equilibrium with the gas phase and can be used in an approximate manner to probe the performance of more general reaction schemes, followed by more detailed analyses using full microkinetic models to determine the surface coverages by adsorbed species and the degrees of rate control of the elementary steps. PMID:27162366

Effective dynamics along given reaction coordinates, and reaction rate theory.

Science.gov (United States)

Zhang, Wei; Hartmann, Carsten; Schütte, Christof

2016-12-22

In molecular dynamics and related fields one considers dynamical descriptions of complex systems in full (atomic) detail. In order to reduce the overwhelming complexity of realistic systems (high dimension, large timescale spread, limited computational resources) the projection of the full dynamics onto some reaction coordinates is examined in order to extract statistical information like free energies or reaction rates. In this context, the effective dynamics that is induced by the full dynamics on the reaction coordinate space has attracted considerable attention in the literature. In this article, we contribute to this discussion: we first show that if we start with an ergodic diffusion process whose invariant measure is unique then these properties are inherited by the effective dynamics. Then, we give equations for the effective dynamics, discuss whether the dominant timescales and reaction rates inferred from the effective dynamics are accurate approximations of such quantities for the full dynamics, and compare our findings to results from approaches like Mori-Zwanzig, averaging, or homogenization. Finally, by discussing the algorithmic realization of the effective dynamics, we demonstrate that recent algorithmic techniques like the "equation-free" approach and the "heterogeneous multiscale method" can be seen as special cases of our approach.

Tandem Reaction of Cationic Copolymerization and Concertedly Induced Hetero-Diels-Alder Reaction Preparing Sequence-Regulated Polymers.

Science.gov (United States)

Matsumoto, Suzuka; Kanazawa, Arihiro; Kanaoka, Shokyoku; Aoshima, Sadahito

2017-06-14

A unique tandem reaction of sequence-controlled cationic copolymerization and site-specific hetero-Diels-Alder (DA) reaction is demonstrated. In the controlled cationic copolymerization of furfural and 2-acetoxyethyl vinyl ether (AcOVE), only the furan ring adjacent to the propagating carbocation underwent the hetero-DA reaction with the aldehyde moiety of another furfural molecule. A further and equally important feature of the copolymerization is that the obtained copolymers had unprecedented 2:(1 + 1)-type alternating structures of repeating sequences of two VE and one furfural units in the main chain and one furfural unit in the side chain. The specific DA reaction is attributed to the delocalization of the positive charge to the side furan ring.

Uranium analysis in urine by inductively coupled plasma dynamic reaction cell mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Ejnik, John W. [Northern Michigan University, Chemistry Department, Marquette, MI (United States); Todorov, Todor I.; Mullick, Florabel G.; Centeno, Jose A. [Armed Forces Institute of Pathology (AFIP), Division of Biophysical Toxicology, Washington, DC (United States); Squibb, Katherine; McDiarmid, Melissa A. [University of Maryland, School of Medicine, Baltimore, MD (United States)

2005-05-01

Urine uranium concentrations are the best biological indicator for identifying exposure to depleted uranium (DU). Internal exposure to DU causes an increased amount of urine uranium and a decreased ratio of {sup 235}U/{sup 238}U in urine samples, resulting in measurements that vary between 0.00725 and 0.002 (i.e., natural and depleted uranium's {sup 235}U/{sup 238}U ratios, respectively). A method based on inductively coupled plasma dynamic reaction cell mass spectrometry (ICP-DRC-MS) was utilized to identify DU in urine by measuring the quantity of total U and the {sup 235}U/{sup 238}U ratio. The quantitative analysis was achieved using {sup 233}U as an internal standard. The analysis was performed both with and without the reaction gas oxygen. The reaction gas converted ionized {sup 235}U{sup +} and {sup 238}U{sup +} into {sup 235}UO{sub 2}{sup +} (m/z=267) and {sup 238}UO{sub 2}{sup +} (m/z=270). This conversion was determined to be over 90% efficient. A polyatomic interference at m/z 234.8 was successfully removed from the {sup 235}U signal under either DRC operating conditions (with or without oxygen as a reaction gas). The method was validated with 15 urine samples of known uranium compositions. The method detection limit for quantification was determined to be 0.1 pg U mL{sup -1} urine and an average coefficient of variation (CV) of 1-2% within the sample measurements. The method detection limit for determining {sup 235}U/{sup 238}U ratio was 3.0 pg U mL{sup -1} urine. An additional 21 patient samples were analyzed with no information about medical history. The measured {sup 235}U/{sup 238}U ratio within the urine samples correctly identified the presence or absence of internal DU exposure in all 21 patients. (orig.)

Scaling analysis in modeling transport and reaction processes a systematic approach to model building and the art of approximation

CERN Document Server

Krantz, William B

2007-01-01

This book is unique as the first effort to expound on the subject of systematic scaling analysis. Not written for a specific discipline, the book targets any reader interested in transport phenomena and reaction processes. The book is logically divided into chapters on the use of systematic scaling analysis in fluid dynamics, heat transfer, mass transfer, and reaction processes. An integrating chapter is included that considers more complex problems involving combined transport phenomena. Each chapter includes several problems that are explained in considerable detail. These are followed by several worked examples for which the general outline for the scaling is given. Each chapter also includes many practice problems. This book is based on recognizing the value of systematic scaling analysis as a pedagogical method for teaching transport and reaction processes and as a research tool for developing and solving models and in designing experiments. Thus, the book can serve as both a textbook and a reference boo...

Integrated corridor management initiative : demonstration phase evaluation - Dallas technical capability analysis test plan.

Science.gov (United States)

This report presents the test plan for conducting the Technical Capability Analysis for the United States : Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor : Management (ICM) Initiative Demonstration. The ...

Enhancement of deuteron-fusion reactions in metals and experimental implications

International Nuclear Information System (INIS)

Huke, A.; Heide, P.; Czerski, K.; Ruprecht, G.; Targosz, N.; Zebrowski, W.

2008-01-01

Recent measurements of the reaction 2 H(d,p) 3 H in metallic environments at very low energies performed by different experimental groups point to an enhanced electron screening effect. However, the resulting screening energies differ strongly for diverse host metals and different experiments. Here, we present new experimental results and investigations of interfering processes in the irradiated targets. These measurements inside metals set special challenges and pitfalls that make them and the data analysis particularly error prone. There are multiparameter collateral effects that are crucial for the correct interpretation of the observed experimental yields. They mainly originate from target surface contaminations owing to residual gases in the vacuum as well as from inhomogeneities and instabilities in the deuteron density distribution in the targets. To address these problems an improved differential analysis method beyond the standard procedures has been implemented. Profound scrutiny of the other experiments demonstrates that the observed unusual changes in the reaction yields are mainly due to deuteron density dynamics simulating the alleged screening energy values. The experimental results are compared with different theoretical models of the electron screening in metals. The Debye-Hueckel model that has been previously proposed to explain the influence of the electron screening on both nuclear reactions and radioactive decays can be clearly excluded

Radiation-reaction effects in the quantum regime

International Nuclear Information System (INIS)

Neitz, Norman

2014-01-01

In this work the influence of radiation reaction on the interaction of an electron bunch with a strong laser field is studied including nonlinear and quantum effects. This venture is motivated by two technological developments: On the one hand, the tremendous increase in available laser intensities and, on the other hand, the significant advancements in electron acceleration technology. Considering a regime where radiation reaction effects are caused by the incoherent emission of several photons, a kinetic approach is developed to describe the dynamics of electrons and photons via distribution functions. Whereas classical electrodynamics, employing the Landau-Lifshitz equation, predicts a narrowing of the energy distribution of the electron beam, the analysis in this work reveals the opposite effect in case that quantum effects become significant. The spreading of the electrons' energy distribution is shown to be caused by the intrinsic stochastic nature of photon emission. In order to explain quantitatively the discrepancy between classical and quantum radiation reaction, the final electron distribution as computed in our quantum treatment is demonstrated to depend on the laser's envelope shape and its duration at a given total laser fluence. On the contrary, the classical analysis does not exhibit such a dependency. Finally, the kinetic approach is extended to allow for the inclusion of pair creation by photons emitted during the scattering. This facilitates a conclusive investigation of the nonlinear coupled dynamics of all particles involved in the interaction, i.e., electrons in the initial bunch, photons and electron-positron pairs produced during the scattering.

Calcium hydroxide silylation reaction with trimethylchlorosilane

Directory of Open Access Journals (Sweden)

Novoselnov Anatoliy A.

2016-01-01

Full Text Available The silylation reaction of a calcium hydroxide with a trimethylchlorosilane is studied as a silylation model by the gas-liquid chromatography. The silylation process is divided into three stages. A material balance of these stages is calculated. The schemes of the reactions at each stage of the process are proposed. The modified calcium hydroxide obtained at three repetitive stages of the silylation reaction has been investigated by the x-ray phase analysis, IR spectroscopy, thermal analysis, electron microscopy in a combination with the elemental analysis. It has been determined that at the first stage of the interaction the processes of the trimethylchlorosilane hydrolysis and of the hydrolysis products condensation dominate, and at the same time an adsorption process of the trimethylchlorosilane and its derivatives starts. Further, the hydrolysis of the trimethylchlorosilane by the «new» portions of a water formed in the reaction of a calcium hydroxide with a hydrogen chloride takes place, simultaneously the secondary reactions of the Si-O-Ca – ties’ formation and cleavage occur including as a silylation-desilylation dynamic equilibrium process.

Policy Analysis Screening System (PASS) demonstration: sample queries and terminal instructions

Energy Technology Data Exchange (ETDEWEB)

None

1979-10-16

This document contains the input and output for the Policy Analysis Screening System (PASS) demonstration. This demonstration is stored on a portable disk at the Environmental Impacts Division. Sample queries presented here include: (1) how to use PASS; (2) estimated 1995 energy consumption from Mid-Range Energy-Forecasting System (MEFS) data base; (3) pollution projections from Strategic Environmental Assessment System (SEAS) data base; (4) diesel auto regulations; (5) diesel auto health effects; (6) oil shale health and safety measures; (7) water pollution effects of SRC; (8) acid rainfall from Energy Environmental Statistics (EES) data base; 1990 EIA electric generation by fuel type; sulfate concentrations by Federal region; forecast of 1995 SO/sub 2/ emissions in Region III; and estimated electrical generating capacity in California to 1990. The file name for each query is included.

Investigation of Na-CO2 Reaction with Initial Reaction in Various Reacting Surface

International Nuclear Information System (INIS)

Kim, Hyun Su; Park, Gunyeop; Kim, Soo Jae; Park, Hyun Sun; Kim, Moo Hwan; Wi, Myung-Hwan

2015-01-01

The reaction products that cause oxidation and erosion are threaten the heat transfer tubes so that it is necessary to investigate Na-CO 2 reaction according to various experimental parameter. Unlike SWR, Na-CO 2 reaction is more complex to deal with reaction kinetics. Since a comprehensive understanding of Na-CO 2 reaction mechanism is crucial for the safety analysis, the reaction phenomenon under the various conditions was investigated. The current issue is to make a database for developing computational code for CO 2 gas leak situation because it is experimentally difficult to analyze the actual accident situation. Most studies on Na-CO 2 interaction reports that chemical reaction is getting vigorous as temperature increased and reactivity is sensitive as temperature change between 400 .deg. C and 600 .deg. C. Therefore, temperature range is determined based on the operating condition (450 - 500 .deg. C) of KALIMER-600 employed as supercritical CO 2 brayton cycle energy conversion system for Na-CO 2 heat exchanger. And next parameter is sodium surface area which contact between sodium and CO 2 when CO 2 is injected into sodium pool in the accident situation. So, the fundamental surface reaction is experimentally studied in the range of 8 - 12cm 2 . Additionally, it has been reported in recent years that CO 2 Flow rate affects reactivity less significantly and CO 2 flow rate is assumed that 5 SLPM (standard liter per minute) is suitable as a basis for a small leakage. The finally selected control parameters is sodium temperature and reacting surface area with constant CO 2 flow rate. Na-CO 2 reaction test is performed for investigating risk of potential accident which contacts with liquid sodium and CO 2 . Amount of reaction is saturated as time passed because of kept a balance between production of solid phase reaction products and amount of diffusivity. These results contribute to make a database for the SFR safety analysis and additional experiments are needed

Scattering and transfer reactions with heavy ions

International Nuclear Information System (INIS)

Hussein, M.S.

From the elastic scattering analysis the input parameters are found for the inelastic scattering analysis and the transfer reactions of the heavy ion reactions. The main theme reported is the likeness and conection among these processes. (L.C.) [pt

Measurement and analysis of $\\alpha$ particle induced reactions on yttrium

CERN Document Server

Singh, N L; Chintalapudi, S N

2000-01-01

Excitation functions for /sup 89/Y[( alpha ,3n); ( alpha ,4n); ( alpha , p3n); ( alpha , alpha n); ( alpha , alpha 2n)] reactions were measured up to 50 MeV using stacked foil activation technique and HPGe gamma ray spectroscopy method. The experimental data were compared with calculations considering equilibrium as well as preequilibrium reactions according to the hybrid model of Blann (ALICE/90). For ( alpha , xnyp) type of reactions, the precompound contributions are described by the model. There seems to be indications of direct inelastic scattering effects in ( alpha , alpha xn) type of reactions. To the best of our knowledge, the excitation functions for ( alpha ,4n), ( alpha , p3n), ( alpha , alpha n) and ( alpha , alpha 2n) reactions were measured for the first time. (23 refs).

Measurement and analysis of alpha particle induced reactions on yttrium

Energy Technology Data Exchange (ETDEWEB)

Singh, N.L.; Gadkari, M.S. [Baroda Univ. (India). Dept. of Physics; Chintalapudi, S.N. [IUC-DAEF Calcutta Centre, Calcutta (India)

2000-05-01

Excitation functions for {sup 89}Y[({alpha},3n);({alpha},4n);({alpha},p3n);({alpha},{alpha}n);({alpha},{alpha}2n)] reactions were measured up to 50 MeV using stacked foil activation technique and HPGe gamma ray spectroscopy method. The experimental data were compared with calculations considering equilibrium as well as preequilibrium reactions according to the hybrid model of Blann (ALICE/90). For ({alpha},xnyp) type of reactions, the precompound contributions are described by the model. There seems to be indications of direct inelastic scattering effects in ({alpha},{alpha}xn) type of reactions. To the best of our knowledge, the excitation functions for ({alpha},4n), ({alpha},p3n), ({alpha},{alpha}n) and ({alpha},{alpha}2n) reactions were measured for the first time. (orig.)

Complexation Key to a pH Locked Redox Reaction

Science.gov (United States)

Rizvi, Masood Ahmad; Dangat, Yuvraj; Shams, Tahir; Khan, Khaliquz Zaman

2016-01-01

An unfavorable pH can block a feasible electron transfer for a pH dependent redox reaction. In this experiment, a series of potentiometric titrations demonstrate the sequential loss in feasibility of iron(II) dichromate redox reaction over a pH range of 0-4. The pH at which this reaction failed to occur was termed as a pH locked reaction. The…

Coating of graphite flakes with MgO/carbon nanocomposite via gas state reaction

Energy Technology Data Exchange (ETDEWEB)

Sharif, M., E-mail: Sharif_m@metaleng.iust.ac.i [Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Faghihi-Sani, M.A. [Sharif University of Technology, Tehran (Iran, Islamic Republic of); Golestani-Fard, F. [Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Saberi, A. [Tabriz University (Iran, Islamic Republic of); Soltani, Ali Khalife [Iran University of Science and Technology, Tehran (Iran, Islamic Republic of)

2010-06-18

Coating of graphite flakes with MgO/carbon nanocomposite was carried out via gaseous state reaction between mixture of Mg metal, CO gas and graphite flakes at 1000 {sup o}C. XRD and FE-SEM analysis of coating showed that the coating was comprised of MgO nano particles and amorphous carbon distributed smoothly and covered the graphite surface evenly. Thermodynamic calculations were employed to predict the reaction sequences as well as phase stability. The effect of coating on water wettability and oxidation resistance of graphite was studied using contact angle measurement and TG analysis, respectively. It was demonstrated that the reaction between Mg and CO could result in MgO/C nanocomposite deposition. The coating improved water wettability of graphite and also enhanced the oxidation resistance of graphite flakes significantly. Also the graphite coating showed significant phenolic resin-wettabilty owing to high surface area of such hydrophilic nano composite coating. The importance of graphite coating is explained with emphasis on its potential application in graphite containing refractories.

Raman Spectral Determination of Chemical Reaction Rate Characteristics

Science.gov (United States)

Balakhnina, I. A.; Brandt, N. N.; Mankova, A. A.; Chikishev, A. Yu.; Shpachenko, I. G.

2017-09-01

The feasibility of using Raman spectroscopy to determine chemical reaction rates and activation energies has been demonstrated for the saponification of ethyl acetate. The temperature dependence of the reaction rate was found in the range from 15 to 45°C.

Analysis of reaction cross-section production in neutron induced fission reactions on uranium isotope using computer code COMPLET.

Science.gov (United States)

Asres, Yihunie Hibstie; Mathuthu, Manny; Birhane, Marelgn Derso

2018-04-22

This study provides current evidence about cross-section production processes in the theoretical and experimental results of neutron induced reaction of uranium isotope on projectile energy range of 1-100 MeV in order to improve the reliability of nuclear stimulation. In such fission reactions of 235 U within nuclear reactors, much amount of energy would be released as a product that able to satisfy the needs of energy to the world wide without polluting processes as compared to other sources. The main objective of this work is to transform a related knowledge in the neutron-induced fission reactions on 235 U through describing, analyzing and interpreting the theoretical results of the cross sections obtained from computer code COMPLET by comparing with the experimental data obtained from EXFOR. The cross section value of 235 U(n,2n) 234 U, 235 U(n,3n) 233 U, 235 U(n,γ) 236 U, 235 U(n,f) are obtained using computer code COMPLET and the corresponding experimental values were browsed by EXFOR, IAEA. The theoretical results are compared with the experimental data taken from EXFOR Data Bank. Computer code COMPLET has been used for the analysis with the same set of input parameters and the graphs were plotted by the help of spreadsheet & Origin-8 software. The quantification of uncertainties stemming from both experimental data and computer code calculation plays a significant role in the final evaluated results. The calculated results for total cross sections were compared with the experimental data taken from EXFOR in the literature, and good agreement was found between the experimental and theoretical data. This comparison of the calculated data was analyzed and interpreted with tabulation and graphical descriptions, and the results were briefly discussed within the text of this research work. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

A mathematical analysis of Prx2-STAT3 disulfide exchange rate constants for a bimolecular reaction mechanism.

Science.gov (United States)

Langford, Troy F; Deen, William M; Sikes, Hadley D

2018-03-22

Appreciation of peroxiredoxins as the major regulators of H 2 O 2 concentrations in human cells has led to a new understanding of redox signaling. In addition to their status as the primary reducers of H 2 O 2 to water, the oxidized peroxiredoxin byproduct of this reaction has recently been shown capable of participation in H 2 O 2 -mediated signaling pathways through disulfide exchange reactions with the transcription factor STAT3. The dynamics of peroxidase-transcription factor disulfide exchange reactions have not yet been considered in detail with respect to how these reactions fit into the larger network of competing reactions in human cells. In this study, we used a kinetic model of oxidation and reduction reactions related to H 2 O 2 metabolism in the cytosol of human cells to study the dynamics of peroxiredoxin-2 mediated oxidation of the redox-regulated transcription factor STAT3. In combination with previously reported experimental data, the model was used to estimate the rate coefficient of a biomolecular reaction between Prx2 and STAT3 for two sets of assumptions that constitute lower and upper bound cases. Using these estimates, we calculated the relative rates of the reaction of oxidized peroxiredoxin-2 and STAT3 and other competing reactions in the cytosol. These calculations revealed that peroxiredoxin-2-mediated oxidation of STAT3 likely occurs at a much slower rate than competing reactions in the cytosol. This analysis suggests the existence of more complex mechanisms, potentially involving currently unknown protein-protein recognition partners, which facilitate disulfide exchange reactions between peroxiredoxin-2 and STAT3. Copyright © 2018 Elsevier Inc. All rights reserved.

Evaluation of the LTQ-Orbitrap mass spectrometer for the analysis of polymerase chain reaction products.

Science.gov (United States)

Manduzio, Hélène; Ezan, Eric; Fenaille, François

2010-12-30

We have investigated the potential and robustness of the off-line coupling of polymerase chain reaction (PCR) with electrospray ionization mass spectrometry (ESI-MS), for further applications in the screening of single-nucleotide polymorphisms (SNPs). This was based on recently reported data demonstrating that anion-exchange solid-phase extraction was the most efficient technique for efficiently desalting PCR products, with a recovery of ∼70%. Results showed that this purification approach efficiently removes almost all the chemicals commonly added to PCR buffers. ESI-MS analysis of a model 114-bp PCR product performed on the LTQ-Orbitrap instrument demonstrated that detection limits in the nM range along with an average mass measurement uncertainty of 9.15 ± 7.11 ppm can be routinely obtained using an external calibration. The PCR/ESI-MS platform was able to detect just a few copies of a targeted oligonucleotide. However, it was shown that if two PCR products are present in a mixture in a ratio higher than 10 to 1, the lower abundance one might not be reproducibly detected. Applications to SNPs demonstrated that an LTQ-Orbitrap with a resolution of 30 000 (at m/z 400) easily identified a single (A ↔ G) switch, i.e. a 16 Da difference, in binary mixtures of ∼ 35 kDa PCR products. Complementary experiments also showed that the combination of endonucleases and ESI-MS could be used to confirm base composition and sequence, and thus to screen for unknown polymorphisms in specific sequences. For example, a single (T ↔ A) switch (9 Da mass difference) was successfully identified in a 114-bp PCR product. Copyright © 2010 John Wiley & Sons, Ltd.

Analysis of a Buchwald-Hartwig amination: reaction for pharmaceutical production

DEFF Research Database (Denmark)

Christensen, Henrik

The Buchwald-Hartwig amination reaction is widely used in the production of N-arylated amines in the pharmaceutical industry. The reaction is betweenan aryl halogen and a primary or secondary amine in the presence of a base and a homogeneous catalyst giving the desired N-arylated amine. Due to mild...... is to increase the understanding of the chem­ical reaction mechanisms and kinetics for the Buchwald-Hartwig amination reaction. Also, to develop methods for application of these mechanisms and kinetics to optimize and scale up an organic synthesis to an industrial phar­maceutical production. The Buchwald...

Analysis of a Buckwald-Hartwig amination: reaction for pharmaceutical production

DEFF Research Database (Denmark)

Christensen, Henrik; Kiil, Søren; Dam-Johansen, Kim

The Buchwald-Hartwig amination reaction is widely used in the production of N-arylated amines in the pharmaceutical industry. The reaction is betweenan aryl halogen and a primary or secondary amine in the presence of a base and a homogeneous catalyst giving the desired N-arylated amine. Due to mild...... is to increase the understanding of the chem­ical reaction mechanisms and kinetics for the Buchwald-Hartwig amination reaction. Also, to develop methods for application of these mechanisms and kinetics to optimize and scale up an organic synthesis to an industrial phar­maceutical production. The Buchwald...

Exploring conditions for the enhancement of acene semiconductors through the use of the Diels-alder reaction

Science.gov (United States)

Qualizza, Brittni A.

This dissertation demonstrates the application of SAMs to the surface of acene crystals, specifically of tetracene and rubrene, using the Diels-Alder reaction. The second chapter details preliminary reaction results and two analytical methods which were employed to confirm adsorption of the dienophile on the surface of single crystals, tetracene and rubrene. These were mass spectrometry and X-ray photoelectron spectroscopy (XPS). Mass spectrometry experiments distinguish the chemical identity of adduct on the crystals and also it discerned chemi- and physisorbed molecules from one another. XPS was used to prove face selectivity of the reaction by the detection of dichloromaleic anhydride. From a mechanistic standpoint, this system demonstrated unusual steric effects: the reaction of one face of the tetracene crystal was virtually inert, while another face was facile. The dienophiles' steric bulk was also expected to play critical role for these confined systems, however analysis of surface data was hindered by the relative lack of corresponding solution kinetic data. While the rate of anthracene's reaction has been studied extensively with a range of dienophiles and tetracene/pentacene has been studied theoretically (with limited experimental reports), an expansive report was generated to aid in future interpretations of acene systems. These kinetic results constitute chapter three.

A Hierarchy of Homodesmotic Reactions for Thermochemistry

Science.gov (United States)

Schleyer, Paul v. R.

2009-01-01

Chemical equations that balance bond types and atom hybridization to different degrees are often used in computational thermochemistry, for example, to increase accuracy when lower levels of theory are employed. We expose the widespread confusion over such classes of equations and demonstrate that the two most widely used definitions of “homodesmotic” reactions are not equivalent. New definitions are introduced and a consistent hierarchy of reaction classes (RC1 – RC5) for hydrocarbons is constructed: isogyric (RC1) ⊇ isodesmic (RC2) ⊇ hypohomodesmotic (RC3) ⊇ homodesmotic (RC4) ⊇ hyperhomodesmotic (RC5). Each of these successively conserves larger molecular fragments. The concept of isodesmic bond separation reactions is generalized to all classes in this hierarchy, providing a unique sectioning of a given molecule for each reaction type. Several ab initio and density functional methods are applied to the bond separation reactions of 38 hydrocarbons containing five or six carbon atoms. RC4 and RC5 reactions provide bond separation enthalpies with errors consistently less than 0.4 kcal mol−1 across a wide range of theoretical levels, performing significantly better than the other reaction types and far superior to atomization routes. Our recommended bond separation reactions were demonstrated by determining the enthalpies of formation (at 298 K) of 1,3,5-hexatriyne (163.7 ± 0.4 kcal mol−1), 1,3,5,7-octatetrayne (217.6 ± 0.6 kcal mol−1), the larger polyynes C10H2 through C26H2, and an infinite acetylenic carbon chain. PMID:19182999

On the graph and systems analysis of reversible chemical reaction networks with mass action kinetics

NARCIS (Netherlands)

Rao, Shodhan; Jayawardhana, Bayu; Schaft, Arjan van der

2012-01-01

Motivated by the recent progresses on the interplay between the graph theory and systems theory, we revisit the analysis of reversible chemical reaction networks described by mass action kinetics by reformulating it using the graph knowledge of the underlying networks. Based on this formulation, we

Actuation of a robotic fish caudal fin for low reaction torque

Science.gov (United States)

Yun, Dongwon; Kim, Kyung-Soo; Kim, Soohyun; Kyung, Jinho; Lee, Sunghee

2011-07-01

In this paper, a novel caudal fin for actuating a robotic fish is presented. The proposed caudal fin waves in a vertical direction with a specific spatial shape, which is determined by a so-called shape factor. For a specific shape factor, a traveling wave with a vertical phase difference is formed on a caudal fin during fin motion. It will be shown by the analysis that the maximum reaction torque at the joint of a caudal fin varies depending on the shape factors. Compared with a conventional plate type caudal fin, the proposed fin with a shape factor of 2π can eliminate the reaction torque perfectly, while keeping the propulsion force unchanged. The benefits of the proposed fin will be demonstrated by experiments.

Sodium water reaction R and D for French LMFBR

International Nuclear Information System (INIS)

Cambillard, E.; Finck, P.; Lapicore, A.; Simeon, C.

1985-01-01

This paper presents the research and development which is underway for the French LMFBR steam generator safety study. The program comprises three major areas: (1) the analysis of realistic leaks, which includes the leak evolution and its consequences; (2) the response time of leak detection systems compared to leak propagation phenomena; and (3) the guillotine rupture (DBA) studies relative to source term evaluation by experimental/calculational approach and mechanical calculations. This program has provided information for the demonstrations of the steam generator safety in respect to a sodium-water reaction

The Effect of Sports and Physical Activity on Elderly Reaction Time and Response Time

Directory of Open Access Journals (Sweden)

Abdolrahman Khezri

2014-07-01

Full Text Available Objectives: Physical activities ameliorate elderly motor and cognitive performance. The aim of this research is to study the effect of sport and physical activity on elderly reaction time and response time. Methods & Materials: The research method is causal-comparative and its statistical population consists of 60 active and non-active old males over 60 years residing at Mahabad city. Reaction time was measured by reaction timer apparatus, made in Takei Company (YB1000 model. Response time was measured via Nelson’s Choice- Response Movement Test. At first, reaction time and then response time was measured. For data analysis, descriptive statistic, K-S Test and One Sample T Test were used Results K-S Test show that research data was parametric. According to the results of this research, physical activity affected reaction time and response time. Results: of T test show that reaction time (P=0.000 and response time (P=0.000 of active group was statistically shorter than non- active group. Conclusion: The result of current study demonstrate that sport and physical activity, decrease reaction and response time via psychomotor and physiological positive changes.

Acidic preparations of lysed platelets upregulate proliferative pathways in osteoblast-like cells as demonstrated by genome-wide microarray analysis.

Science.gov (United States)

Wahlström, Ola; Linder, Cecilia Halling; Ansell, Anna; Kalén, Anders; Söderström, Mats; Magnusson, Per

2011-01-01

Platelets contain numerous growth factors essential for wound and fracture healing. We investigated the gene expression in human osteoblast-like cells stimulated with lysed platelets prepared in acidic, neutral, or alkaline buffers. Lysed platelets prepared in buffers at pH 5.4, 7.4, and 7.9, were added after neutralization to hFOB 1.19 cells. Genome-wide microarray analysis was performed using the Affymetrix GeneChip 7G Scanner. Biometric, cluster, and pathway analyses were performed with GeneSpring GX. Biometric analyses demonstrated that 53 genes were differentially regulated (p ≤ 0.005, ≥2-fold increase). Pathway analysis revealed 10 significant pathways of which eight are common ones regulating bone formation and cancer growth. Eleven genes were selected for quantitative real-time polymerase chain reaction (PCR) based on the microarray analysis of the lysed platelets prepared in the pH 5.4 experiments. In conclusion, acidic preparations of lysed platelet concentrates release factors essential for cell proliferation and particularly cell metabolism under hypoxic conditions. The genetic response from these factors was dominated by genes associated with the same pathways observed in bone formation and cancer growth. Activation of TGF-β in the acidic preparation could be a stimulatory key factor of cell proliferation. These results support the hypothesis that acidification of platelets modifies the stimulatory response of mesenchymal cells in vitro, which is analogous with the observed milieu of a low pH present in wound and fracture sites, as well as in growing tumors.

Analysis of gas absorption to a thin liquid film in the presence of a zero-order chemical reaction

Science.gov (United States)

Rajagopalan, S.; Rahman, M. M.

1995-01-01

The paper presents a detailed theoretical analysis of the process of gas absorption to a thin liquid film adjacent to a horizontal rotating disk. The film is formed by the impingement of a controlled liquid jet at the center of the disk and subsequent radial spreading of liquid along the disk. The chemical reaction between the gas and the liquid film can be expressed as a zero-order homogeneous reaction. The process was modeled by establishing equations for the conservation of mass, momentum, and species concentration and solving them analytically. A scaling analysis was used to determine dominant transport processes. Appropriate boundary conditions were used to solve these equations to develop expressions for the local concentration of gas across the thickness of the film and distributions of film height, bulk concentration, and Sherwood number along the radius of the disk. The partial differential equation for species concentration was solved using the separation of variables technique along with the Duhamel's theorem and the final analytical solution was expressed using confluent hypergeometric functions. Tables for eigenvalues and eigenfunctions are presented for a number of reaction rate constants. A parametric study was performed using Reynolds number, Ekman number, and dimensionless reaction rate as parameters. At all radial locations, Sherwood number increased with Reynolds number (flow rate) as well as Ekman number (rate of rotation). The enhancement of mass transfer due to chemical reaction was found to be small when compared to the case of no reaction (pure absorption), but the enhancement factor was very significant when compared to pure absorption in a stagnant liquid film. The zero-order reaction processes considered in the present investigation included the absorption of oxygen in aqueous alkaline solutions of sodiumdithionite and rhodium complex catalyzed carbonylation of methanol. Present analytical results were compared to previous theoretical

Lithium analysis using a double-sided silicon strip detector at LIBAF

Science.gov (United States)

De La Rosa, Nathaly; Kristiansson, Per; Nilsson, E. J. Charlotta; Ros, Linus; Elfman, Mikael; Pallon, Jan

2017-08-01

Quantification and mapping possibilities of lithium in geological material, by Nuclear Reaction Analysis (NRA), was evaluated at the Lund Ion Beam Analysis Facility (LIBAF). LiF and two Standard Reference Materials, (SRM 610 and SRM 612) were used in the investigation. The main part of the data was obtained at the beam energy 635 keV studying the high Q-value reaction 7Li(p, α)4He, but reaction yield and detection limits were also briefly investigated as a function of the energy. A double-sided silicon strip detector (DSSSD) was used to detect the α -particles emitted in the reaction in the backward direction. The combination of the high Q-value, a reasonably good cross-section and the possibility to use a high beam current have been demonstrated to allow for measurement of concentrations down below 50 ppm. Proton energies below 800 keV were demonstrated to be appropriate energies for extracting lithium in combination with boron analysis.

A Demonstrative Analysis of News Articles Using Fairclough’s Critical Discourse Analysis Framework

Directory of Open Access Journals (Sweden)

Roy Randy Y. Briones

2017-07-01

Full Text Available This paper attempts to demonstrate Norman Fairclough’s Critical Discourse Analysis (CDA framework by conducting internal and external level analyses on two online news articles that report on the Moro Islamic Liberation Front’s (MILF submission of its findings on the “Mamasapano Incident” that happened in the Philippines in 2015. In performing analyses using this framework, the social context and background for these texts, as well as the relationship between the internal discourse features and the external social practices and structures in which the texts were produced are thoroughly examined. As a result, it can be noted that from the texts’ internal discourse features, the news articles portray ideological and social distinctions among social actors such as the Philippine Senate, the SAF troopers, the MILF, the MILF fighters, and the civilians. Moreover, from the viewpoint of the texts as being external social practices, the texts maintain institutional identities as news reports, but they also reveal some evaluative stance as exemplified by the adjectival phrases that the writers employed. Having both the internal and external features examined, it can be said that the way these texts were written seems to portray power relations that exist between the Philippine government and the MILF. Key words: Critical Discourse Analysis, discourse analysis, news articles, social practices, social structures, power relations

Quantitative in situ monitoring of an elevated temperature reaction using a water-cooled mid-infrared fiber-optic probe.

Science.gov (United States)

Maclaurin, P; Crabb, N C; Wells, I; Worsfold, P J; Coombs, D

1996-04-01

A novel water-cooled mid-infrared fiber-optic probe is described which is heatable to 230 °C. The probe has chalcogenide fibers and a ZnSe internal reflection element and is compact and fully flexible, allowing access to a wide range of standard laboratory reaction vessels and fume cupboard arrangements. Performance is demonstrated via the in situ analysis of an acid-catalyzed esterification reaction in toluene at 110 °C, and the results are compared with those from a conventional extractive sampling loop flow cell arrangement. Particular emphasis is given to the quantitative interpretation of the spectroscopic data, using gas chromatographic reference data. Calibration data are presented for univariate and partial least squares models, with an emphasis on procedures for improving the quality of interpreparation calibration and prediction through the use of focused reference analysis regimes. Subset univariate procedures are presented that yield relative errors of spectroscopy combined with bias correction partial least squares procedures for the efficient in situ quantitative analysis of laboratory scale reactions.

Exogenous reference gene normalization for real-time reverse transcription-polymerase chain reaction analysis under dynamic endogenous transcription.

Science.gov (United States)

Johnston, Stephen; Gallaher, Zachary; Czaja, Krzysztof

2012-05-15

Quantitative real-time reverse transcription-polymerase chain reaction (qPCR) is widely used to investigate transcriptional changes following experimental manipulations to the nervous system. Despite the widespread utilization of qPCR, the interpretation of results is marred by the lack of a suitable reference gene due to the dynamic nature of endogenous transcription. To address this inherent deficiency, we investigated the use of an exogenous spike-in mRNA, luciferase, as an internal reference gene for the 2(-∆∆Ct) normalization method. To induce dynamic transcription, we systemically administered capsaicin, a neurotoxin selective for C-type sensory neurons expressing the TRPV-1 receptor, to adult male Sprague-Dawley rats. We later isolated nodose ganglia for qPCR analysis with the reference being either exogenous luciferase mRNA or the commonly used endogenous reference β-III tubulin. The exogenous luciferase mRNA reference clearly demonstrated the dynamic expression of the endogenous reference. Furthermore, variability of the endogenous reference would lead to misinterpretation of other genes of interest. In conclusion, traditional reference genes are often unstable under physiologically normal situations, and certainly unstable following the damage to the nervous system. The use of exogenous spike-in reference provides a consistent and easily implemented alternative for the analysis of qPCR data.

Predictors of chronic ankle instability: Analysis of peroneal reaction time, dynamic balance and isokinetic strength.

Science.gov (United States)

Sierra-Guzmán, Rafael; Jiménez, Fernando; Abián-Vicén, Javier

2018-05-01

Previous studies have reported the factors contributing to chronic ankle instability, which could lead to more effective treatments. However, factors such as the reflex response and ankle muscle strength have not been taken into account in previous investigations. Fifty recreational athletes with chronic ankle instability and 55 healthy controls were recruited. Peroneal reaction time in response to sudden inversion, isokinetic evertor muscle strength and dynamic balance with the Star Excursion Balance Test and the Biodex Stability System were measured. The relationship between the Cumberland Ankle Instability Tool score and performance on each test was assessed and a backward multiple linear regression analysis was conducted. Participants with chronic ankle instability showed prolonged peroneal reaction time, poor performance in the Biodex Stability System and decreased reach distance in the Star Excursion Balance Test. No significant differences were found in eversion and inversion peak torque. Moderate correlations were found between the Cumberland Ankle Instability Tool score and the peroneal reaction time and performance on the Star Excursion Balance Test. Peroneus brevis reaction time and the posteromedial and lateral directions of the Star Excursion Balance Test accounted for 36% of the variance in the Cumberland Ankle Instability Tool. Dynamic balance deficits and delayed peroneal reaction time are present in participants with chronic ankle instability. Peroneus brevis reaction time and the posteromedial and lateral directions of the Star Excursion Balance Test were the main contributing factors to the Cumberland Ankle Instability Tool score. No clear strength impairments were reported in unstable ankles. Copyright © 2018 Elsevier Ltd. All rights reserved.

Analysis of Return and Forward Links from STARS' Flight Demonstration 1

Science.gov (United States)

Gering, James A.

2003-01-01

Space-based Telemetry And Range Safety (STARS) is a Kennedy Space Center (KSC) led proof-of-concept demonstration, which utilizes NASA's space network of Tracking and Data Relay Satellites (TDRS) as a pathway for launch and mission related information streams. Flight Demonstration 1 concluded on July 15,2003 with the seventh flight of a Low Power Transmitter (LPT) a Command and Data Handler (C&DH), a twelve channel GPS receiver and associated power supplies and amplifiers. The equipment flew on NASA's F-I5 aircraft at the Dryden Flight Research Center located at Edwards Air Force Base in California. During this NASA-ASEE Faculty Fellowship, the author participated in the collection and analysis of data from the seven flights comprising Flight Demonstration 1. Specifically, the author examined the forward and return links bit energy E(sub B) (in Watt-seconds) divided by the ambient radio frequency noise N(sub 0) (in Watts / Hertz). E(sub b)/N(sub 0) is commonly thought of as a signal-to-noise parameter, which characterizes a particular received radio frequency (RF) link. Outputs from the data analysis include the construction of time lines for all flights, production of graphs of range safety values for all seven flights, histograms of range safety E(sub b)/N(sub 0) values in five dB increments, calculation of associated averages and standard deviations, production of graphs of range user E(sub b)/N(sub 0) values for the all flights, production of graphs of AGC's and E(sub b)/N(sub 0) estimates for flight 1, recorded onboard, transmitted directly to the launch head and transmitted through TDRS. The data and graphs are being used to draw conclusions related to a lower than expected signal strength seen in the range safety return link.

Bordetella pertussis diagnosed by polymerase chain reaction

DEFF Research Database (Denmark)

Birkebaek, N H; Heron, I; Skjødt, K

1994-01-01

The object of this work was to test the polymerase chain reaction (PCR) for demonstration of Bordetella pertussis (BP) in nasopharyngeal secretions. The method was applied to patients with recently diagnosed pertussis, as verified by BP culture. In order to test the sensitivity and specificity...... in 25 patients in whose nasopharyngeal secretions BP had been demonstrated after 4-7 days of culture. The detection limit of PCR in aqueous solution was 1-2 BP bacteria per reaction tube. PCR was 100% specific for BP, showing no response with other Bordetella species or other bacteria known to colonize...

Generating Converged Accurate Free Energy Surfaces for Chemical Reactions with a Force-Matched Semiempirical Model.

Science.gov (United States)

Kroonblawd, Matthew P; Pietrucci, Fabio; Saitta, Antonino Marco; Goldman, Nir

2018-04-10

We demonstrate the capability of creating robust density functional tight binding (DFTB) models for chemical reactivity in prebiotic mixtures through force matching to short time scale quantum free energy estimates. Molecular dynamics using density functional theory (DFT) is a highly accurate approach to generate free energy surfaces for chemical reactions, but the extreme computational cost often limits the time scales and range of thermodynamic states that can feasibly be studied. In contrast, DFTB is a semiempirical quantum method that affords up to a thousandfold reduction in cost and can recover DFT-level accuracy. Here, we show that a force-matched DFTB model for aqueous glycine condensation reactions yields free energy surfaces that are consistent with experimental observations of reaction energetics. Convergence analysis reveals that multiple nanoseconds of combined trajectory are needed to reach a steady-fluctuating free energy estimate for glycine condensation. Predictive accuracy of force-matched DFTB is demonstrated by direct comparison to DFT, with the two approaches yielding surfaces with large regions that differ by only a few kcal mol -1 .

Heavy ion transfer reactions

International Nuclear Information System (INIS)

Weisser, D.C.

1977-06-01

To complement discussions on the role of γ rays in heavy ion induced reactions, the author discusses the role played by particle detection. Transfer reactions are part of this subject and are among those in which one infers the properties of the residual nucleus in a reaction by observing the emerging light nucleus. Inelastic scattering ought not be excluded from this subject, although no particles are transferred, because of the role it plays in multistep reactions and in fixing O.M. parameters describing the entrance channel of the reaction. Heavy ion transfer reaction studies have been under study for some years and yet this research is still in its infancy. The experimental techniques are difficult and the demands on theory rigorous. One of the main products of heavy ion research has been the thrust to re-examine the assumptions of reaction theory and now include many effects neglected for light ion analysis. This research has spurred the addition of multistep processes to simple direct processes and coupled channel calculations. (J.R.)

Detailed analysis of allergic cutaneous reactions to spinal cord stimulator devices

Directory of Open Access Journals (Sweden)

Chaudhry ZA

2013-08-01

Full Text Available Zeshan Ahmed Chaudhry,1 Umer Najib,2 Zahid H Bajwa,3 W Carl Jacobs,4 Javed Sheikh,5 Thomas T Simopoulos61Department of Diagnostic and Interventional Neuroradiology, Massachusetts General Hospital/Harvard Medical School, Boston, MA, USA; 2Department of Neurology, Robert C Byrd Health Sciences Center of West Virginia University, Morgantown, WV, USA; 3Boston Headache Institute, Waltham, MA, USA; 4Department of Pathology, Beth Israel Deaconess Medical Center, Harvard Medical School, Boston, MA, USA; 5Department of Medicine, Allergy and Immunology, 6Department of Anesthesia, Beth Israel Deaconess Medical Center, Brookline, MA, USAAbstract: The use of spinal cord stimulation (SCS devices to treat chronic, refractory neuropathic pain continues to expand in application. While device-related complications have been well described, inflammatory reactions to the components of these devices remain underreported. In contrast, hypersensitivity reactions associated with other implanted therapies, such as endovascular and cardiac rhythm devices, have been detailed. The purpose of this case series is to describe the clinical presentation and course of inflammatory reactions as well as the histology of these reactions. All patients required removal of the entire device after developing inflammatory reactions over a time course of 1–3 months. Two patients developed a foreign body reaction in the lead insertion wound as well as at the implantable pulse generator site, with histology positive for giant cells. One patient developed an inflammatory dermatitis on the flank and abdomen that resolved with topical hydrocortisone. “In vivo” testing with a lead extension fragment placed in the buttock resulted in a negative reaction followed by successful reimplantation of an SCS device. Inflammatory reactions to SCS devices can manifest as contact dermatitis, granuloma formation, or foreign body reactions with giant cell formation. Tissue diagnosis is essential, and

Analysis of the nucleon-nucleus reactions by the quantum molecular dynamics

International Nuclear Information System (INIS)

Chiba, Satoshi; Niita, Koji; Maruyama, Toshiki; Fukahori, Tokio; Takada, Hiroshi; Iwamoto, Akira

1995-01-01

The quantum molecular dynamics + statistical decay model has been applied to analyze the nucleon-induced nuclear reactions in the energy range from 50 to 3 GeV in order to verify its applicability to light-ion induced nuclear reactions. It was found that the present approach could give a quantitative description of various cross sections such as (p,p'), (p,n), (n,p) reactions from a wide range of targets and also target-like isotope production cross sections from p+Fe reaction, showing its basic ability as a tool for the study of intermediate energy nuclear reactions and nuclear data evaluation. (author)

Amazing variational approach to chemical reactions

OpenAIRE

Fernández, Francisco M.

2009-01-01

In this letter we analyse an amazing variational approach to chemical reactions. Our results clearly show that the variational expressions are unsuitable for the analysis of empirical data obtained from chemical reactions.

Theoretical considerations of Flow Injection Analysis in the Absence of Chemical Reactions

DEFF Research Database (Denmark)

Andersen, Jens Enevold Thaulov

2000-01-01

The fundamental mechanism of flow injection analysis (FIA) is assumed to be simple dissusion and the response of the detector is included in a model description that provide information about the shape of the FIA peak in terms of, basically, five parameters. Two of the five parameters are associa...... that any deviation from the features of the present model and the results of a tentative chemical reaction with one of the test compounds, is related to chemical kinetics.......The fundamental mechanism of flow injection analysis (FIA) is assumed to be simple dissusion and the response of the detector is included in a model description that provide information about the shape of the FIA peak in terms of, basically, five parameters. Two of the five parameters...

Study of the (p,d3He) reaction as a quasi-free reaction process

International Nuclear Information System (INIS)

Cowley, A.A.; Roos, P.G.; Chant, N.S.; Woody, R. III; Holmgren, H.D.; Goldberg, D.A.

1976-11-01

The (p,d 3 He) reaction on 6 Li, 7 Li, 9 Be, and 12 C has been investigated in conjunction with studies of the (p,pα) reaction on the same targets. Coincident data for all four targets were obtained at a bombarding energy of 100 MeV for numerous angle pairs in order to test the reaction mechanism. Comparisons of the (p,d 3 He) data to both (p,pα) data and distorted wave impulse approximation calculations (DWIA) indicate a dominance of the direct quasi-free reaction process (p + alpha yields d + 3 He). The absolute alpha-particle spectroscopic factors extracted using DWIA analysis are in agreement with the values obtained in the (p,pα) reaction

A Fluorogenic Aromatic Nucleophilic Substitution Reaction for Demonstrating Normal-Phase Chromatography and Isolation of Nitrobenzoxadiazole Chromophores

Science.gov (United States)

Key, Jessie A.; Li, Matthew D.; Cairo, Christopher W.

2011-01-01

Normal-phase chromatography is an essential technique for monitoring chemical reactions, identifying the presence of specific components, as well as the purification of organic compounds. An experiment to facilitate the instruction and understanding of the concepts behind normal-phase chromatography at the introductory and intermediate…

Data analysis on work activities in dismantling of Japan Power Demonstration Reactor (JPDR). Contract research

International Nuclear Information System (INIS)

Shiraishi, Kunio; Sukegawa, Takenori; Yanagihara, Satoshi

1998-03-01

The safe dismantling of a retired nuclear power plant was demonstrated by completion of dismantling activities for the Japan Power Demonstration Reactor (JPDR), March, 1996, which had been conducted since 1986. This project was a flag ship project for dismantling of nuclear power plants in Japan, aiming at demonstrating an applicability of developed dismantling techniques in actual dismantling work, developing database on work activities as well as dismantling of components and structures. Various data on dismantling activities were therefore systematically collected and these were accumulated on computer files to build the decommissioning database; dismantling activities were characterized by analyzing the data. The data analysis resulted in producing general forms such as unit activity factors, for example, manpower need per unit weight of component to be dismantled, and simple arithmetic forms for forecasting of project management data to be applied to planning another dismantling project through the evaluation for general use of the analyzed data. The results of data analysis could be usefully applied to planning of future decommissioning of commercial nuclear power plants in Japan. This report describes the data collection and analysis on the JPDR dismantling activities. (author)

Alkali Silica Reaction In The Presence Of Metakaolin - The Significant Role of Calcium Hydroxide

Science.gov (United States)

Zapała-Sławeta, Justyna

2017-10-01

Reducing the internal corrosion, which is the result of reactions between alkalis and reactive aggregates is especially important in ensuring durability properties of concrete. One of the methods of inhibiting the reaction is using some mineral additives which have pozzolanic properties. This paper presents the efficacy of high-reactivity metakaolin in reducing expansion due to alkali-silica reaction. It was demonstrated that metakaolin in the amount from 5% to 20% by mass of Portland cement reduce linear expansion of mortar bars with opal aggregate. Nevertheless, the safe expansion level in the specimens, classified as non-destructive to concrete, was recorded for the mortars prepared with 20% addition of metakaolin. Depletion of free calcium hydroxide content was considered as one of the most beneficial effects of metakaolin in controlling alkali silica reaction. Based on thermogravimetric analysis (TGA) performed on mortar bars with and without metakaolin the differences in portlandite content were determined. Microstructural observation of the specimens containing metakaolin indicated the presence of a reaction products but fewer in number than those forming in the mortars without mineral additives.

Experimental investigation of solid sodium-water reaction: tests results and phenomenological analysis

International Nuclear Information System (INIS)

Daudin, K.; Beauchamp, F.; Proust, C.

2014-01-01

Sodium-Water Reaction (SWR) is an issue one has to be capable to deal with for the next generation of nuclear reactors (SFR for GEN IV). The background of these experiments is the improvement of safety demonstration regarding SWR in an open volume. This experimental campaign is conducted at the CEA Cadarache inside a cylindrical reactor filled with inert gas. The sodium is inside a loading pot and water comes into contact by immersion. SWR and its physical effects are followed by different pressure and temperature sensors. The results show a limit to the overpressure increasing sodium mass. Global assessment of physical effects of SWR contributes to put forward the relative nature of phenomena with geometric configuration, and the importance of scale effects. (authors)

Structural analysis of CuO / CeO2-based catalytic materials intended for PROX reaction: Part I

International Nuclear Information System (INIS)

Neiva, L.S.; Simoes, A.N.; Bispo, A.; Ribeiro, M.A.; Gama, L.

2011-01-01

This work relates the synthesis process of CuO/CeO 2 catalytic materials by a combustion reaction method as well as it introduces a structural analysis of the developed material, this structural analysis had as main focus to evaluate the influence of the doping substance (CuO) when being incorporated in the hostess matrix structure that is CeO 2 . The CuO/CeO catalytic materials developed in this work are destined to preferential oxidation of CO reaction (PROX). The developed materials were characterized by XRD, SEM and textural complete analysis by the BET method. According to the results, the CuO incorporation changed crystallinity of the structure of the catalytic materials. On the other hand, the morphologic and textural characteristics did not showed significant differences regarding the presence of the doping substance (CuO) in the structure of the developed materials. The porosity of the structures of the developed catalytic materials belongs to the type macroporous. (author)

Chemical changes in groundwater and their reaction rates

International Nuclear Information System (INIS)

Talma, A.S.

1981-01-01

The evolution of the major ion concentrations of groundwater (Na, K, Ca, Mg, HCO 3 , SO 4 , Cl and NO 3 ) can be described as the consequence of a number of competing chemical reactions. With the aid of the naturally occuring radioactive and stable isotopes some of these reactions can be separated, identified and followed in space and time. In some field studies, especialy of artesian water, the rates of reactions can be estimated. A number of processes observed in South African sandstones aquifers are discussed and the variable reaction rates demonstrated. Reactions that can be identified include carbonate solution, chemical weathering, salt leaching, cation exchange and redox processes

Bayesian inversion analysis of nonlinear dynamics in surface heterogeneous reactions.

Science.gov (United States)

Omori, Toshiaki; Kuwatani, Tatsu; Okamoto, Atsushi; Hukushima, Koji

2016-09-01

It is essential to extract nonlinear dynamics from time-series data as an inverse problem in natural sciences. We propose a Bayesian statistical framework for extracting nonlinear dynamics of surface heterogeneous reactions from sparse and noisy observable data. Surface heterogeneous reactions are chemical reactions with conjugation of multiple phases, and they have the intrinsic nonlinearity of their dynamics caused by the effect of surface-area between different phases. We adapt a belief propagation method and an expectation-maximization (EM) algorithm to partial observation problem, in order to simultaneously estimate the time course of hidden variables and the kinetic parameters underlying dynamics. The proposed belief propagation method is performed by using sequential Monte Carlo algorithm in order to estimate nonlinear dynamical system. Using our proposed method, we show that the rate constants of dissolution and precipitation reactions, which are typical examples of surface heterogeneous reactions, as well as the temporal changes of solid reactants and products, were successfully estimated only from the observable temporal changes in the concentration of the dissolved intermediate product.

Copper-catalyzed oxidative Heck reactions between alkyltrifluoroborates and vinyl arenes.

Science.gov (United States)

Liwosz, Timothy W; Chemler, Sherry R

2013-06-21

We report herein that potassium alkyltrifluoroborates can be utilized in oxidative Heck-type reactions with vinyl arenes. The reaction is catalyzed by a Cu(OTf)2/1,10-phenanthroline with MnO2 as the stoichiometric oxidant. In addition to the alkyl Heck, amination, esterification, and dimerization reactions of alkyltrifluoroborates are demonstrated under analogous reaction conditions. Evidence for an alkyl radical intermediate is presented.

Depressurization accident analysis of MPBR by PBRSIM with chemical reaction model

International Nuclear Information System (INIS)

No, Hee Cheon; Kadak, A. C.

2002-01-01

The simple model for natural circulation is implemented into PBR S IM to provide air inlet velocity from the containment air space. For the friction and form loss only the pebble region is considered conservatively modeling laminar flow through a packed bed. For the chemical reaction model of PBR S IM the oxidation rate is determined as the minimum value of three mechanisms estimated at each time step: oxygen mass flow rate entering the bottom of the reflector, oxidation rate by kinetics, and oxygen mass flow rate arriving at the graphite surface by diffusion. Oxygen mass flux arriving at the graphite surface by diffusion is estimated based on energy-mass analogy. Two types of exothermic chemical reaction are considered: (C + zO 2 → xCO + yCO 2 ) and (2CO + O 2 2CO 2 ). The heterogeneous and homogeneous chemical reaction rates by kinetics are determined by INEEL and Bruno correlations, respectively. The instantaneous depressurization accident of MPBR is simulated using PBR S IM with chemical model. The air inlet velocity is initially rapidly dropped within 10 hr and reaches a saturation value of about 1.5cm/s. The oxidation rate by the diffusion process becomes lower than that by the chemical kinetics above 600K. The maximum pebble bed temperatures without and with chemical reaction reach the peak values of 1560 and 1617 .deg. C at 80 hr and 92 hr, respectively. As the averaged temperatures in the bottom reflector and the pebble bed regions increase with time, (C+1/2O2 ->CO) reaction becomes dominant over (C+O 2 →CO 2 ) reaction. Also, the CO generated by (C+1/2O 2 →CO) reaction will be consumed by (2CO+O 2 →2CO 2 ) reaction and the energy homogeneously generated by this CO depletion reaction becomes dominant over the heterogeneous reaction

Sensitive inexpensive spectrophotometric and spectrofluorimetric analysis of ezogabine, levetiracetam and topiramate in tablet formulations using Hantzsch condensation reaction

Science.gov (United States)

Ibrahim, F. A.; El-Yazbi, A. F.; Wagih, M. M.; Barary, M. A.

2017-09-01

Two highly sensitive, simple and selective spectrophotometric and spectrofluorimetric assays have been investigated for the analysis of ezogabine, levetiracetam and topiramate in their pure and in pharmaceutical dosage forms. The suggested methods depend on the condensation of the primary amino-groups in the three drugs with acetylacetone and formaldehyde according to Hantzsch reaction yielding highly fluorescent yellow colored dihydropyridine derivatives. The reaction products of ezogabine, levetiracetam and topiramate were measured spectrophotometrically at 418, 390 and 380 nm or spectrofluorimetrically at λem/ex of 495/425 nm, 490/415 nm and 488/410 nm, respectively. Various experimental conditions have been carefully studied to maximize the reaction yield. At the optimum reaction conditions, the calibration curves were rectilinear over the concentration ranges of 8-25, 60-180 and 80-200 μg/mL spectrophotometrically and 0.02-0.2, 0.2-1.2 and 0.2-1.5 μg/mL spectrofluorimetrically for ezogabine, levetiracetam and topiramate, respectively with good correlation coefficients. The suggested methods were applied successfully for the analysis of ezogabine, levetiracetam and topiramate in their commercial tablets with high percentage recoveries and negligible interference from various excipients in pharmaceutical dosage forms. The results were statistically analyzed and showed the absence of any significant difference between both developed and published methods. The procedures were validated and evaluated by the ICH guidelines revealing good reproducibility and accuracy. Therefore, the two proposed methods may be considered of high interest for practical and reliable analysis of ezogabine, levetiracetam and topiramate in pharmaceutical dosage forms.

Integrated corridor management initiative : demonstration phase evaluation, San Diego technical capability analysis test plan.

Science.gov (United States)

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Direct Measurements of Half-Cycle Reaction Heats during Atomic Layer Deposition by Calorimetry

Energy Technology Data Exchange (ETDEWEB)

Lownsbury, James M. [Department; Gladden, James A. [Department; Campbell, Charles T. [Department; Department; Kim, In Soo [Materials; Martinson, Alex B. F. [Materials

2017-10-05

We introduce a new high-temperature adsorption calorimeter that approaches the ideal limit of a heat detector whereby the signal at any time is proportional to the heat power being delivered to the sample and prove its sensitivity for measuring pulse-to-pulse heats of half-reactions during atomic layer deposition (ALD) at 400 K. The heat dynamics of amorphous Al2O3 growth via sequential self-limiting surface reaction of trimethylaluminum (TMA) and H2O is clearly resolved. Calibration enables quantitation of the exothermic TMA and H2O half-reactions with high precision, -343 kJ/mol TMA and -251 kJ/mol H2O, respectively. A time resolution better than 1 ms is demonstrated, allowing for the deconvolution of at least two distinct surface reactions during TMA microdosing. It is further demonstrated that this method can provide the heat of reaction versus extent of reaction during each precursors half-reaction, thus providing even richer mechanistic information on the surface processes involved. The broad applicability of this novel calorimeter is demonstrated through excellent signal-to-noise ratios of less exothermic ALD half-reactions to produce TiO2 and MnO.

Reliability demonstration test planning using bayesian analysis

International Nuclear Information System (INIS)

Chandran, Senthil Kumar; Arul, John A.

2003-01-01

In Nuclear Power Plants, the reliability of all the safety systems is very critical from the safety viewpoint and it is very essential that the required reliability requirements be met while satisfying the design constraints. From practical experience, it is found that the reliability of complex systems such as Safety Rod Drive Mechanism is of the order of 10 -4 with an uncertainty factor of 10. To demonstrate the reliability of such systems is prohibitive in terms of cost and time as the number of tests needed is very large. The purpose of this paper is to develop a Bayesian reliability demonstrating testing procedure for exponentially distributed failure times with gamma prior distribution on the failure rate which can be easily and effectively used to demonstrate component/subsystem/system reliability conformance to stated requirements. The important questions addressed in this paper are: With zero failures, how long one should perform the tests and how many components are required to conclude with a given degree of confidence, that the component under test, meets the reliability requirement. The procedure is explained with an example. This procedure can also be extended to demonstrate with more number of failures. The approach presented is applicable for deriving test plans for demonstrating component failure rates of nuclear power plants, as the failure data for similar components are becoming available in existing plants elsewhere. The advantages of this procedure are the criterion upon which the procedure is based is simple and pertinent, the fitting of the prior distribution is an integral part of the procedure and is based on the use of information regarding two percentiles of this distribution and finally, the procedure is straightforward and easy to apply in practice. (author)

Deep-inelastic multinucleon transfer processes in the 16O+27Al reaction

Science.gov (United States)

Roy, B. J.; Sawant, Y.; Patwari, P.; Santra, S.; Pal, A.; Kundu, A.; Chattopadhyay, D.; Jha, V.; Pandit, S. K.; Parkar, V. V.; Ramachandran, K.; Mahata, K.; Nayak, B. K.; Saxena, A.; Kailas, S.; Nag, T. N.; Sahoo, R. N.; Singh, P. P.; Sekizawa, K.

2018-03-01

The reaction mechanism of deep-inelastic multinucleon transfer processes in the 16O+27Al reaction at an incident 16O energy (Elab=134 MeV) substantially above the Coulomb barrier has been studied both experimentally and theoretically. Elastic-scattering angular distribution, total kinetic energy loss spectra, and angular distributions for various transfer channels have been measured. The Q -value- and angle-integrated isotope production cross sections have been deduced. To obtain deeper insight into the underlying reaction mechanism, we have carried out a detailed analysis based on the time-dependent Hartree-Fock (TDHF) theory. A recently developed method, TDHF+GEMINI, has been applied to evaluate production cross sections for secondary products. From a comparison between the experimental and theoretical cross sections, we find that the theory qualitatively reproduces the experimental data. Significant effects of secondary light-particle emissions are demonstrated. Possible interplay among fusion-fission, deep-inelastic, multinucleon transfer, and particle evaporation processes is discussed.

Electromagnetic radiation reaction force and radiation potential in general five-dimensional relativity

International Nuclear Information System (INIS)

Lo, C.Y.; Goldstein, G.R.; Napier, A.

1989-01-01

A unified theory of electromagnetic and gravitational fields should modify classical electrodynamics to account for the radiation reaction force. A conjecture that the radiation reaction force and the Lorentz force should be distinct, but in unified forms, results in a five-dimensional unified theory of five variables. It is found that a semicylindrical condition can reconcile the apparent differences between a five-dimensional physical space and our four-dimensional perceptions. Analysis of the geodesic equations results in the notion of gauge dynamics which manifests the influence of the unrestricted fifth variable. The element g 55 of the five-dimensional metric is identified as the radiation potential, which can directly determine the radiation reaction force. This gives a distinct physical origin for the radiation process in classical theory. The potential suggests that the electron can have excited states in quantum electrodynamics. This theory is supported with calculations which demonstrate that the motion of the fifth variable directly causes physical changes in the four-dimensional subspace

High School Forum: "Invitations to Enquiry": The Calcite/Acid Reaction.

Science.gov (United States)

Herron, J. Dudley, Ed.; Driscoll, D. R.

1979-01-01

Describes a high school chemistry experiment which involves the reaction between calcite and hydrochloric and sulfuric acids. This reaction can be carried out as a projected demonstration and on an individual basis. (HM)

Paterno`-Bu¨chi Reaction as a Demonstration of Chemical Kinetics and Synthetic Photochemistry Using a Light Emitting Diode Apparatus

Science.gov (United States)

Thompson, Matthew P.; Agger, Jonathan; Wong, Lu Shin

2015-01-01

The Paterno`-Bu¨chi photocycloaddition reaction is used as the basis for physical-organic final-year undergraduate laboratory experiments designed to emphasize the multidisciplinary approach to modern-day chemical practice. These reactions are performed using commercially available LED-based light sources, which offer a convenient and safe tool…

Possibility of analysis using RBS, PIXE and nuclear reaction on the electrostatic Pelletron accelerator 5SDH-2

International Nuclear Information System (INIS)

Nguyen The Nghia; Bui Van Loat; Le Hong Khiem

2011-01-01

The electrostatic Pelletron accelerator 5SDH-2 is installing at Hanoi University of Sciences. This accelerator will be the first tandem electrostatic accelerator installed in Vietnam. The schematic structure, principle of operation of the machine and its application for analysis using Rutherford Back Scattering (RBS), Particle-Induced X-ray Emission (PIXE) and Nuclear Reaction Analysis (NRA) will be presented. (author)

Photosynthesis energy factory: analysis, synthesis, and demonstration. Final report

Energy Technology Data Exchange (ETDEWEB)

1978-11-01

This quantitative assessment of the potential of a combined dry-land Energy Plantation, wood-fired power plant, and algae wastewater treatment system demonstrates the cost-effectiveness of recycling certain by-products and effluents from one subsystem to another. Designed to produce algae up to the limit of the amount of carbon in municipal wastewater, the algae pond provides a positive cash credit, resulting mainly from the wastewater treatment credit, which may be used to reduce the cost of the Photosynthesis Energy Factory (PEF)-generated electricity. The algae pond also produces fertilizer, which reduces the cost of the biomass produced on the Energy Plantation, and some gas. The cost of electricity was as low as 35 mills per kilowatt-hour for a typical municipally-owned PEF consisting of a 65-MWe power plant, a 144-acre algae pond, and a 33,000-acre Energy Plantation. Using only conventional or near-term technology, the most cost-effective algae pond for a PEF is the carbon-limited secondary treatment system. This system does not recycle CO/sub 2/ from the flue gas. Analysis of the Energy Plantation subsystem at 15 sites revealed that plantations of 24,000 to 36,000 acres produce biomass at the lowest cost per ton. The following sites are recommended for more detailed evaluation as potential demonstration sites: Pensacola, Florida; Jamestown, New York; Knoxville, Tennessee; Martinsville, Virginia, and Greenwood, South Carolina. A major possible extension of the PEF concept is to include the possibility for irrigation.

Quantification of Hydrogen Concentrations in Surface and Interface Layers and Bulk Materials through Depth Profiling with Nuclear Reaction Analysis.

Science.gov (United States)

Wilde, Markus; Ohno, Satoshi; Ogura, Shohei; Fukutani, Katsuyuki; Matsuzaki, Hiroyuki

2016-03-29

Nuclear reaction analysis (NRA) via the resonant (1)H((15)N,αγ)(12)C reaction is a highly effective method of depth profiling that quantitatively and non-destructively reveals the hydrogen density distribution at surfaces, at interfaces, and in the volume of solid materials with high depth resolution. The technique applies a (15)N ion beam of 6.385 MeV provided by an electrostatic accelerator and specifically detects the (1)H isotope in depths up to about 2 μm from the target surface. Surface H coverages are measured with a sensitivity in the order of ~10(13) cm(-2) (~1% of a typical atomic monolayer density) and H volume concentrations with a detection limit of ~10(18) cm(-3) (~100 at. ppm). The near-surface depth resolution is 2-5 nm for surface-normal (15)N ion incidence onto the target and can be enhanced to values below 1 nm for very flat targets by adopting a surface-grazing incidence geometry. The method is versatile and readily applied to any high vacuum compatible homogeneous material with a smooth surface (no pores). Electrically conductive targets usually tolerate the ion beam irradiation with negligible degradation. Hydrogen quantitation and correct depth analysis require knowledge of the elementary composition (besides hydrogen) and mass density of the target material. Especially in combination with ultra-high vacuum methods for in-situ target preparation and characterization, (1)H((15)N,αγ)(12)C NRA is ideally suited for hydrogen analysis at atomically controlled surfaces and nanostructured interfaces. We exemplarily demonstrate here the application of (15)N NRA at the MALT Tandem accelerator facility of the University of Tokyo to (1) quantitatively measure the surface coverage and the bulk concentration of hydrogen in the near-surface region of a H2 exposed Pd(110) single crystal, and (2) to determine the depth location and layer density of hydrogen near the interfaces of thin SiO2 films on Si(100).

Computational methodology of sodium-water reaction phenomenon in steam generator of sodium-cooled fast reactor

International Nuclear Information System (INIS)

Takata, Takashi; Yamaguchi, Akira; Uchibori, Akihiro; Ohshima, Hiroyuki

2009-01-01

A new computational methodology of sodium-water reaction (SWR), which occurs in a steam generator of a liquid-sodium-cooled fast reactor when a heat transfer tube in the steam generator fails, has been developed considering multidimensional and multiphysics thermal hydraulics. Two kinds of reaction models are proposed in accordance with a phase of sodium as a reactant. One is the surface reaction model in which water vapor reacts directly with liquid sodium at the interface between the liquid sodium and the water vapor. The reaction heat will lead to a vigorous evaporation of liquid sodium, resulting in a reaction of gas-phase sodium. This is designated as the gas-phase reaction model. These two models are coupled with a multidimensional, multicomponent gas, and multiphase thermal hydraulics simulation method with compressibility (named the 'SERAPHIM' code). Using the present methodology, a numerical investigation of the SWR under a pin-bundle configuration (a benchmark analysis of the SWAT-1R experiment) has been carried out. As a result, the maximum gas temperature of approximately 1,300degC is predicted stably, which lies within the range of previous experimental observations. It is also demonstrated that the maximum temperature of the mass weighted average in the analysis agrees reasonably well with the experimental result measured by thermocouples. The present methodology will be promising to establish a theoretical and mechanical modeling of secondary failure propagation of heat transfer tubes due to such as an overheating rupture and a wastage. (author)

Analysis of charged particle induced reactions for beam monitor applications

Energy Technology Data Exchange (ETDEWEB)

Surendra Babu, K. [IOP, Academia Sinica, Taipe, Taiwan (China); Lee, Young-Ouk [Nuclear Data Evaluation Laboratory, Korea Atomic Energy Research Institute (Korea, Republic of); Mukherjee, S., E-mail: smukherjee_msuphy@yahoo.co.in [Department of Physics, Faculty of Science, M.S. University of Baroda, Vadodara 390 002 (India)

2012-07-15

The reaction cross sections for different residual nuclides produced in the charged particle (p, d, {sup 3}He and {alpha}) induced reactions were calculated and compared with the existing experimental data which are important for beam monitoring and medical diagnostic applications. A detailed literature compilation and comparison were made on the available data sets for the above reactions. These calculations were carried out using the statistical model code TALYS up to 100 MeV, which contains Kalbach's latest systematic for the emission of complex particles and complex particle-induced reactions. All optical model calculations were performed by ECIS-03, which is built into TALYS. The level density, optical model potential parameters were adjusted to get the better description of experimental data. Various pre-equilibrium models were used in the present calculations with default parameters.

Measurement and analysis of cross sections for (p,x) reactions on natural molybdenum

International Nuclear Information System (INIS)

Challan, M. B.; Comsan, M.N.H.; Abou-Zeid, M.A.

2006-01-01

Excitation functions (EFs) for the reactions n atMo(p,x) 92m Nb, and n atMo(p,x) 94 , 95m , 95g , 96 m, +g , 99m Tc up to 18 MeV from threshold have been measured employing the stacked foil activation technique, and using high resolution HPGe gamma spectrometry. Utilizing the simultaneous measurement of the excitation function of n atCu(p,x) 62 Zn, n atCu(p,x) 63 Zn, n atCu(p,x) 65 Zn, and n atTi(p,x) 48 V monitor reactions. The theoretical analysis of the EFs has been done using both the semi-classical as well as quantum mechanical codes which include compound nucleus and pre-equilibrium (PE) emission into consideration. In general, theoretical calculations agree well with the experimental data. Effect of various free parameters used in the calculations has also been discussed. A significant contribution of pre-equilibrium component has been observed at these energies

Comparison of vertical ground reaction forces during overground and treadmill running. A validation study

Directory of Open Access Journals (Sweden)

Kluitenberg Bas

2012-11-01

Full Text Available Abstract Background One major drawback in measuring ground-reaction forces during running is that it is time consuming to get representative ground-reaction force (GRF values with a traditional force platform. An instrumented force measuring treadmill can overcome the shortcomings inherent to overground testing. The purpose of the current study was to determine the validity of an instrumented force measuring treadmill for measuring vertical ground-reaction force parameters during running. Methods Vertical ground-reaction forces of experienced runners (12 male, 12 female were obtained during overground and treadmill running at slow, preferred and fast self-selected running speeds. For each runner, 7 mean vertical ground-reaction force parameters of the right leg were calculated based on five successful overground steps and 30 seconds of treadmill running data. Intraclass correlations (ICC(3,1 and ratio limits of agreement (RLOA were used for further analysis. Results Qualitatively, the overground and treadmill ground-reaction force curves for heelstrike runners and non-heelstrike runners were very similar. Quantitatively, the time-related parameters and active peak showed excellent agreement (ICCs between 0.76 and 0.95, RLOA between 5.7% and 15.5%. Impact peak showed modest agreement (ICCs between 0.71 and 0.76, RLOA between 19.9% and 28.8%. The maximal and average loading-rate showed modest to excellent ICCs (between 0.70 and 0.89, but RLOA were higher (between 34.3% and 45.4%. Conclusions The results of this study demonstrated that the treadmill is a moderate to highly valid tool for the assessment of vertical ground-reaction forces during running for runners who showed a consistent landing strategy during overground and treadmill running. The high stride-to-stride variance during both overground and treadmill running demonstrates the importance of measuring sufficient steps for representative ground-reaction force values. Therefore, an

Investigation of Na-CO{sub 2} Reaction with Initial Reaction in Various Reacting Surface

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyun Su; Park, Gunyeop; Kim, Soo Jae; Park, Hyun Sun; Kim, Moo Hwan [POSTECH, Pohang (Korea, Republic of); Wi, Myung-Hwan [KAERI, Daejeon (Korea, Republic of)

2015-10-15

The reaction products that cause oxidation and erosion are threaten the heat transfer tubes so that it is necessary to investigate Na-CO{sub 2} reaction according to various experimental parameter. Unlike SWR, Na-CO{sub 2} reaction is more complex to deal with reaction kinetics. Since a comprehensive understanding of Na-CO{sub 2} reaction mechanism is crucial for the safety analysis, the reaction phenomenon under the various conditions was investigated. The current issue is to make a database for developing computational code for CO{sub 2} gas leak situation because it is experimentally difficult to analyze the actual accident situation. Most studies on Na-CO{sub 2} interaction reports that chemical reaction is getting vigorous as temperature increased and reactivity is sensitive as temperature change between 400 .deg. C and 600 .deg. C. Therefore, temperature range is determined based on the operating condition (450 - 500 .deg. C) of KALIMER-600 employed as supercritical CO{sub 2} brayton cycle energy conversion system for Na-CO{sub 2} heat exchanger. And next parameter is sodium surface area which contact between sodium and CO{sub 2} when CO{sub 2} is injected into sodium pool in the accident situation. So, the fundamental surface reaction is experimentally studied in the range of 8 - 12cm{sup 2}. Additionally, it has been reported in recent years that CO{sub 2} Flow rate affects reactivity less significantly and CO{sub 2} flow rate is assumed that 5 SLPM (standard liter per minute) is suitable as a basis for a small leakage. The finally selected control parameters is sodium temperature and reacting surface area with constant CO{sub 2} flow rate. Na-CO{sub 2} reaction test is performed for investigating risk of potential accident which contacts with liquid sodium and CO{sub 2}. Amount of reaction is saturated as time passed because of kept a balance between production of solid phase reaction products and amount of diffusivity. These results contribute to make a

The analysis of magnesium oxide hydration in three-phase reaction system

Energy Technology Data Exchange (ETDEWEB)

Tang, Xiaojia; Guo, Lin; Chen, Chen; Liu, Quan; Li, Tie; Zhu, Yimin, E-mail: ntp@dlmu.edu.cn

2014-05-01

In order to investigate the magnesium oxide hydration process in gas–liquid–solid (three-phase) reaction system, magnesium hydroxide was prepared by magnesium oxide hydration in liquid–solid (two-phase) and three-phase reaction systems. A semi-empirical model and the classical shrinking core model were used to fit the experimental data. The fitting result shows that both models describe well the hydration process of three-phase system, while only the semi-empirical model right for the hydration process of two-phase system. The characterization of the hydration product using X-Ray diffraction (XRD) and scanning electron microscope (SEM) was performed. The XRD and SEM show hydration process in the two-phase system follows common dissolution/precipitation mechanism. While in the three-phase system, the hydration process undergo MgO dissolution, Mg(OH){sub 2} precipitation, Mg(OH){sub 2} peeling off from MgO particle and leaving behind fresh MgO surface. - Graphical abstract: There was existence of a peeling-off process in the gas–liquid–solid (three-phase) MgO hydration system. - Highlights: • Magnesium oxide hydration in gas–liquid–solid system was investigated. • The experimental data in three-phase system could be fitted well by two models. • The morphology analysis suggested that there was existence of a peel-off process.

Insights into the mechanisms on chemical reactions: reaction paths for chemical reactions

International Nuclear Information System (INIS)

Dunning, T.H. Jr.; Rosen, E.; Eades, R.A.

1987-01-01

We report reaction paths for two prototypical chemical reactions: Li + HF, an electron transfer reaction, and OH + H 2 , an abstraction reaction. In the first reaction we consider the connection between the energetic terms in the reaction path Hamiltonian and the electronic changes which occur upon reaction. In the second reaction we consider the treatment of vibrational effects in chemical reactions in the reaction path formalism. 30 refs., 9 figs

Investigation of structural properties associated with alkali-silica reaction by means of macro- and micro-structural analysis

International Nuclear Information System (INIS)

Mo Xiangyin; Fournier, Benoit

2007-01-01

Structural properties associated with alkali-silica reaction were systematically investigated by means of macro-structural accelerated mortar prism expansion levels testing, combined with micro-structural analysis. One part of this study is to determine the reactivity of the aggregate by means of accelerated mortar bar tests, and also to evaluate perlite aggregate constituents, especially the presence of deleterious components and find main causes of the alkali-silica reaction, which was based on the petrographic studies by optical microscope and the implication of X-ray diffraction on the aggregate. Results implied that the aggregate was highly alkali-silica reactive and the main micro-crystalline quartz-intermediate character and matrix that is mainly composed of chalcedony are potentially suitable for alkali-silica reaction. The other part is to study the long-term effect of lithium salts against alkali-silica reaction by testing accelerated mortar prism expansion levels. The macro-structural results were also consistent with the micro-structural mechanisms of alkali-silica reaction of mortar prisms containing this aggregate and the effect of chemical admixtures by means of the methods of scanning electron microscope-X-ray energy-dispersive spectroscopy and X-ray diffraction. It was indicated by these techniques that lithium salts, which were introduced into concrete containing reactive aggregate at the mixing stage, suppressed the alkali-silica reaction by producing non-expansive crystalline materials

Giant resonances in heavy-ion reactions

International Nuclear Information System (INIS)

Hussein, M.S.

1982-11-01

The several roles of multipole giant resonances in heavy-ion reactions are discussed. In particular, the modifications in the effective ion-ion potencial due to the virtual excitation of giant resonances at low energies, are considered and estimated for several systems. Real excitation of giant resonances in heavy-ion reactions at intermediate energies are then discussed and their importance in the approach phase of deeply inelastic processes in emphasized. Several demonstrative examples are given. (Author) [pt

Photocatalytic degradation of paracetamol: intermediates and total reaction mechanism.

Science.gov (United States)

Moctezuma, Edgar; Leyva, Elisa; Aguilar, Claudia A; Luna, Raúl A; Montalvo, Carlos

2012-12-01

The advanced oxidation of paracetamol (PAM) promoted by TiO(2)/UV system in aqueous medium was investigated. Monitoring this reaction by HPLC and TOC, it was demonstrated that while oxidation of paracetamol is quite efficient under these conditions, its mineralization is not complete. HPLC indicated the formation of hydroquinone, benzoquinone, p-aminophenol and p-nitrophenol in the reaction mixtures. Further evidence of p-nitrophenol formation was obtained following the reaction by UV-vis spectroscopy. Continuous monitoring by IR spectroscopy demonstrated the breaking of the aromatic amide present in PAM and subsequent formation of several aromatic intermediate compounds such as p-aminophenol and p-nitrophenol. These aromatic compounds were eventually converted into trans-unsaturated carboxylic acids. Based on these experimental results, an alternative deacylation mechanism for the photocatalytic oxidation of paracetamol is proposed. Our studies also demonstrated IR spectroscopy to be a useful technique to investigate oxidative mechanisms of pharmaceutical compounds. Copyright © 2012 Elsevier B.V. All rights reserved.

Competing definitions: a public policy analysis of the federal recreational fee demonstration program

Science.gov (United States)

Thomas A. E. More

2003-01-01

Problem definition theory specifies that however controls the definition of a problem is in a unique position to control debate over the issue, influence others, and determine the problem's place on the agenda. This paper uses a rhetorical analysis and a questionnaire survey of congressional aides to examine the federal Recreational Fee Demonstration Program....

Filtering reaction dynamics using nearside-farside theory and local angular momentum theory: application to the angular scattering of the H + D2(v(i) = 0, j(i) = 0) --> HD(v(f) = 3, j(f) = 0) + D reaction in the energy and time domains.

Science.gov (United States)

Monks, P D D; Connor, J N L; Bouakline, F

2009-04-23

We investigate methods for filtering reaction mechanisms in the angular scattering of the state-to-state reaction, H + D(2)(v(i) = 0, j(i) = 0, m(i) = 0) --> HD(v(f) = 3, j(f) = 0, m(f) = 0) + D, where v(i), j(i), and m(i) and v(f), j(f), and m(f) are initial and final vibrational, rotational, and helicity quantum numbers, respectively. The input to our filtrations is a new set of accurate quantum scattering matrix elements for total energies in the range 1.52-2.50 eV (in steps of 0.01 eV) and for total angular momentum quantum numbers in the range, 0-40, in steps of unity. We filter reaction mechanisms in both the energy domain and the time domain. The time-domain calculations employ the plane wave packet formulation of time-dependent scattering. The theoretical tools used are nearside-farside (NF) analysis of partial wave series for scattering amplitudes, together with NF local angular momentum (LAM) theory. An energy-domain LAM analysis reveals the existence of an important dynamical feature in the N scattering, a "trench" which bisects the (energy, angle) plane. We use the location of this trench to approximately filter two reaction mechanisms. Transformation to the time domain demonstrates that the two reaction mechanisms correspond to direct and delayed (by about 25 fs) scattering. Further analysis, including filtration in the time domain, shows that the pronounced LAM trench arises from the interference of the energy-domain analogues of the time-direct and time-delayed scattering. Our theory and results provide the first successful demonstration of reaction mechanism filtering carried out directly in the (energy, angle) domain. The calculations and results in this paper extend and complement earlier research reported by Monks, Connor, and Althorpe (Monks, P. D. D.; Connor, J. N. L.; Althorpe, S. C. J. Phys. Chem. A 2006, 110, 741; J. Phys. Chem. A 2007, 111, 10302).

Nuclear reactions as structure probes

International Nuclear Information System (INIS)

Fernandez, Bernard; Cugnon, Joseph; Roussel-Chomaz, Patricia; Sparenberg, Jean-Marc; Oliveira Santos, Francois de; Bauge, Eric; Poves, Alfredo; Keeley, Nicholas; Simenel, Cedric; Avez, Benoit; Lacroix, Denis; Baye, Daniel; Cortina-Gil, Dolores; Pons, Alexandre

2007-09-01

This publication gathers courses which aim at giving a view on new experiments which are performed by using radioactive beams, notably low intensity beams, in different accelerators, and allow the structure of very exotic nuclei to be characterized. Experimental as well as theoretical aspects are thus addressed. The contributions propose: a brief history of nuclear reactions and of instruments used to study them from the discovery of nucleus to the DWBA (Distorted Wave Born Approximation); an overview of nuclear reactions; experimental techniques; the theory of collisions at low energy; resonant elastic scattering, inelastic scattering and astrophysical reactions; to probe nuclear structure with nucleons; shell model and spectroscopic factors; analysis of transfer reactions and determination of spectroscopic factors; microscopic approaches of nuclear dynamics; theoretical aspects of dissociation reactions; experimental aspects of knockout reactions; research in oenology with the chemical characterisation of defective ageing of dry white wines

Experimental (Network) and Evaluated Nuclear Reaction Data at NDS

International Nuclear Information System (INIS)

Otsuka, N.; Semkova, V.; Simakov, S.P.; Zerkin, V.

2011-01-01

Dr Simakov of Nuclear Data Services Unit in the Nuclear Data Section (NDS) gave a brief overview of the data compilation and evaluation activities in the nuclear data community: experimental nuclear reaction data (EXFOR, http://www-nds.iaea.org/exfor/) and evaluated nuclear reaction data (ENDF, http://www-nds.iaea.org/endf). The International Network of Nuclear Reaction Data Centres (NRDC) coordinated by NDS includes 14 Centres in 8 Countries (China, Hungary, India, Japan, Korea, Russian, Ukraine, USA) and 2 International Organizations (NEA, IAEA). It had the first meeting of four core centres (Brookhaven, Saclay, Obninsk, Vienna) in 1966 and the EXFOR was adopted as an official data exchange format. In 2000, IAEA implemented the EXFOR database as a relational multiform database and the EXFOR is a trusted, increasing and living database with 19100 experimental works (as of September 2011) and 141600 data tables. The EXFOR provides a compilation control system for selection of articles and compilation of data and the NRDC home page provides manuals, documents and codes. The nuclear data can be retrieved by the web-retrieval system or distributed on a DVD on request. The EXFOR data play a critical role in the development of evaluated nuclear reaction data. There are several major general purpose libraries: ENDF (US), CENDL (China), JEFF (EU), JENDL (Japan) and RUSFOND (Russia). In addition, there are special libraries for particular applications: EAF (European Activation File), FENDL (Fusion Evaluated Nuclear Data Library for ITER neutronics), IBANDL (Ion Beam Analysis Nuclear Data Library for surface analysis of solids), IRDF, DXS (Dosimetry, radiation damage and gas production data) and Medical portal. Dr V. Zerkin of NDS demonstrated the data retrieval from the EXFOR database and the ENDF library.

Experimental (Network) and Evaluated Nuclear Reaction Data at NDS

Energy Technology Data Exchange (ETDEWEB)

Otsuka, N; Semkova, V; Simakov, S P; Zerkin, V [Nuclear Data Services Unit, Nuclear Data Section, IAEA, Vienna (Austria)

2011-11-15

Dr Simakov of Nuclear Data Services Unit in the Nuclear Data Section (NDS) gave a brief overview of the data compilation and evaluation activities in the nuclear data community: experimental nuclear reaction data (EXFOR, http://www-nds.iaea.org/exfor/) and evaluated nuclear reaction data (ENDF, http://www-nds.iaea.org/endf). The International Network of Nuclear Reaction Data Centres (NRDC) coordinated by NDS includes 14 Centres in 8 Countries (China, Hungary, India, Japan, Korea, Russian, Ukraine, USA) and 2 International Organizations (NEA, IAEA). It had the first meeting of four core centres (Brookhaven, Saclay, Obninsk, Vienna) in 1966 and the EXFOR was adopted as an official data exchange format. In 2000, IAEA implemented the EXFOR database as a relational multiform database and the EXFOR is a trusted, increasing and living database with 19100 experimental works (as of September 2011) and 141600 data tables. The EXFOR provides a compilation control system for selection of articles and compilation of data and the NRDC home page provides manuals, documents and codes. The nuclear data can be retrieved by the web-retrieval system or distributed on a DVD on request. The EXFOR data play a critical role in the development of evaluated nuclear reaction data. There are several major general purpose libraries: ENDF (US), CENDL (China), JEFF (EU), JENDL (Japan) and RUSFOND (Russia). In addition, there are special libraries for particular applications: EAF (European Activation File), FENDL (Fusion Evaluated Nuclear Data Library for ITER neutronics), IBANDL (Ion Beam Analysis Nuclear Data Library for surface analysis of solids), IRDF, DXS (Dosimetry, radiation damage and gas production data) and Medical portal. Dr V. Zerkin of NDS demonstrated the data retrieval from the EXFOR database and the ENDF library.

The Maillard Reaction Reduced the Sensitization of Tropomyosin and Arginine Kinase from Scylla paramamosain, Simultaneously.

Science.gov (United States)

Han, Xin-Yu; Yang, Huang; Rao, Shi-Tao; Liu, Guang-Yu; Hu, Meng-Jun; Zeng, Bin-Chang; Cao, Min-Jie; Liu, Guang-Ming

2018-03-21

The Maillard reaction was established to reduce the sensitization of tropomyosin (TM) and arginine kinase (AK) from Scylla paramamosain, and the mechanism of the attenuated sensitization was investigated. In the present study, the Maillard reaction conditions were optimized for heating at 100 °C for 60 min (pH 8.5) with arabinose. A low level of allergenicity in mice was shown by the levels of allergen-specific antibodies, and more Th1 and less Th2 cells cytokines produced and associated transcription factors with the Maillard reacted allergen (mAllergen). The tolerance potency in mice was demonstrated by the increased ratio of Th1/Th2 cytokines. Moreover, mass spectrometry analysis showed that some key amino acids of IgE-binding epitopes (K 112 , R 125 , R 133 of TM; K 33 , K 118 , R 202 of AK) were modified by the Maillard reaction. The Maillard reaction with arabinose reduced the sensitization of TM and AK, which may be due to the masked epitopes.

Design, development, and demonstration of a fully LabVIEW controlled in situ electrochemical Fourier transform infrared setup combined with a wall-jet electrode to investigate the electrochemical interface of nanoparticulate electrocatalysts under reaction conditions.

Science.gov (United States)

Nesselberger, Markus; Ashton, Sean J; Wiberg, Gustav K H; Arenz, Matthias

2013-07-01

We present a detailed description of the construction of an in situ electrochemical ATR-FTIR setup combined with a wall-jet electrode to investigate the electrocatalytic properties of nanoparticulate catalysts in situ under controlled mass transport conditions. The presented setup allows the electrochemical interface to be probed in combination with the simultaneous determination of reaction rates. At the same time, the high level of automation allows it to be used as a standard tool in electrocatalysis research. The performance of the setup was demonstrated by probing the oxygen reduction reaction on a platinum black catalyst in sulfuric electrolyte.

Reaction Wheel Disturbance Model Extraction Software - RWDMES

Science.gov (United States)

Blaurock, Carl

2009-01-01

The RWDMES is a tool for modeling the disturbances imparted on spacecraft by spinning reaction wheels. Reaction wheels are usually the largest disturbance source on a precision pointing spacecraft, and can be the dominating source of pointing error. Accurate knowledge of the disturbance environment is critical to accurate prediction of the pointing performance. In the past, it has been difficult to extract an accurate wheel disturbance model since the forcing mechanisms are difficult to model physically, and the forcing amplitudes are filtered by the dynamics of the reaction wheel. RWDMES captures the wheel-induced disturbances using a hybrid physical/empirical model that is extracted directly from measured forcing data. The empirical models capture the tonal forces that occur at harmonics of the spin rate, and the broadband forces that arise from random effects. The empirical forcing functions are filtered by a physical model of the wheel structure that includes spin-rate-dependent moments (gyroscopic terms). The resulting hybrid model creates a highly accurate prediction of wheel-induced forces. It accounts for variation in disturbance frequency, as well as the shifts in structural amplification by the whirl modes, as the spin rate changes. This software provides a point-and-click environment for producing accurate models with minimal user effort. Where conventional approaches may take weeks to produce a model of variable quality, RWDMES can create a demonstrably high accuracy model in two hours. The software consists of a graphical user interface (GUI) that enables the user to specify all analysis parameters, to evaluate analysis results and to iteratively refine the model. Underlying algorithms automatically extract disturbance harmonics, initialize and tune harmonic models, and initialize and tune broadband noise models. The component steps are described in the RWDMES user s guide and include: converting time domain data to waterfall PSDs (power spectral

TCE degradation in groundwater by chelators-assisted Fenton-like reaction of magnetite: Sand columns demonstration.

Science.gov (United States)

Jia, Daqing; Sun, Sheng-Peng; Wu, Zhangxiong; Wang, Na; Jin, Yaoyao; Dong, Weiyang; Chen, Xiao Dong; Ke, Qiang

2018-03-15

Trichloroethylene (TCE) degradation in sand columns has been investigated to evaluate the potential of chelates-enhanced Fenton-like reaction with magnetite as iron source for in situ treatment of TCE-contaminated groundwater. The results showed that successful degradation of TCE in sand columns was obtained by nitrilotriacetic acid (NTA)-assisted Fenton-like reaction of magnetite. Addition of ethylenediaminedisuccinic acid (EDDS) resulted in an inhibitory effect on TCE degradation in sand columns. Similar to EDDS, addition of ethylenediaminetetraacetic acid (EDTA) also led to an inhibition of TCE degradation in sand column with small content of magnetite (0.5 w.t.%), but enhanced TCE degradation in sand column with high content of magnetite (7.0 w.t.%). Additionally, the presence of NTA, EDDS and EDTA greatly decreased H 2 O 2 uptake in sand columns due to the competition between chelates and H 2 O 2 for surface sites on magnetite (and sand). Furthermore, the presented results show that magnetite in sand columns remained stable in a long period operation of 230 days without significant loss of performance in terms of TCE degradation and H 2 O 2 uptake. Moreover, it was found that TCE was degraded mainly to formic acid and chloride ion, and the formation of chlorinated organic intermediates was minimal by this process. Copyright © 2017 Elsevier B.V. All rights reserved.

Comprehensive genetic analysis of early host body reactions to the bioactive and bio-inert porous scaffolds.

Directory of Open Access Journals (Sweden)

Tomo Ehashi

Full Text Available To design scaffolds for tissue regeneration, details of the host body reaction to the scaffolds must be studied. Host body reactions have been investigated mainly by immunohistological observations for a long time. Despite of recent dramatic development in genetic analysis technologies, genetically comprehensive changes in host body reactions are hardly studied. There is no information about host body reactions that can predict successful tissue regeneration in the future. In the present study, porous polyethylene scaffolds were coated with bioactive collagen or bio-inert poly(2-methacryloyloxyethyl phosphorylcholine-co-n-butyl methacrylate (PMB and were implanted subcutaneously and compared the host body reaction to those substrates by normalizing the result using control non-coat polyethylene scaffold. The comprehensive analyses of early host body reactions to the scaffolds were carried out using a DNA microarray assay. Within numerous genes which were expressed differently among these scaffolds, particular genes related to inflammation, wound healing, and angiogenesis were focused upon. Interleukin (IL-1β and IL-10 are important cytokines in tissue responses to biomaterials because IL-1β promotes both inflammation and wound healing and IL-10 suppresses both of them. IL-1β was up-regulated in the collagen-coated scaffold. Collagen-specifically up-regulated genes contained both M1- and M2-macrophage-related genes. Marked vessel formation in the collagen-coated scaffold was occurred in accordance with the up-regulation of many angiogenesis-inducible factors. The DNA microarray assay provided global information regarding the host body reaction. Interestingly, several up-regulated genes were detected even on the very bio-inert PMB-coated surfaces and those genes include inflammation-suppressive and wound healing-suppressive IL-10, suggesting that not only active tissue response but also the inert response may relates to these genetic

Comprehensive Genetic Analysis of Early Host Body Reactions to the Bioactive and Bio-Inert Porous Scaffolds

Science.gov (United States)

Ehashi, Tomo; Takemura, Taro; Hanagata, Nobutaka; Minowa, Takashi; Kobayashi, Hisatoshi; Ishihara, Kazuhiko; Yamaoka, Tetsuji

2014-01-01

To design scaffolds for tissue regeneration, details of the host body reaction to the scaffolds must be studied. Host body reactions have been investigated mainly by immunohistological observations for a long time. Despite of recent dramatic development in genetic analysis technologies, genetically comprehensive changes in host body reactions are hardly studied. There is no information about host body reactions that can predict successful tissue regeneration in the future. In the present study, porous polyethylene scaffolds were coated with bioactive collagen or bio-inert poly(2-methacryloyloxyethyl phosphorylcholine-co-n-butyl methacrylate) (PMB) and were implanted subcutaneously and compared the host body reaction to those substrates by normalizing the result using control non-coat polyethylene scaffold. The comprehensive analyses of early host body reactions to the scaffolds were carried out using a DNA microarray assay. Within numerous genes which were expressed differently among these scaffolds, particular genes related to inflammation, wound healing, and angiogenesis were focused upon. Interleukin (IL)-1β and IL-10 are important cytokines in tissue responses to biomaterials because IL-1β promotes both inflammation and wound healing and IL-10 suppresses both of them. IL-1β was up-regulated in the collagen-coated scaffold. Collagen-specifically up-regulated genes contained both M1- and M2-macrophage-related genes. Marked vessel formation in the collagen-coated scaffold was occurred in accordance with the up-regulation of many angiogenesis-inducible factors. The DNA microarray assay provided global information regarding the host body reaction. Interestingly, several up-regulated genes were detected even on the very bio-inert PMB-coated surfaces and those genes include inflammation-suppressive and wound healing-suppressive IL-10, suggesting that not only active tissue response but also the inert response may relates to these genetic regulations. PMID:24454803

Microscopic description of nuclear reactions

International Nuclear Information System (INIS)

Gorbatov, A.M.

1992-01-01

The genealogical series method has been extended to the continuous spectrum of the many-body systems. New nonlinear integral equations have been formulated to perform the microscopical description of the nuclear reactions with arbitrary number of particles. The way to solve them numerically is demonstrated

Selective population of high-j states via heavy-ion-induced transfer reactions

International Nuclear Information System (INIS)

Bond, P.D.

1982-01-01

One of the early hopes of heavy-ion-induced transfer reactions was to populate states not seen easily or at all by other means. To date, however, I believe it is fair to say that spectroscopic studies of previously unknown states have had, at best, limited success. Despite the early demonstration of selectivity with cluster transfer to high-lying states in light nuclei, the study of heavy-ion-induced transfer reactions has emphasized the reaction mechanism. The value of using two of these reactions for spectroscopy of high spin states is demonstrated: 143 Nd( 16 O, 15 O) 144 Nd and 170 Er( 16 O, 15 Oγ) 171 Er

Photosynthesis Is Widely Distributed among Proteobacteria as Demonstrated by the Phylogeny of PufLM Reaction Center Proteins

Directory of Open Access Journals (Sweden)

Johannes F. Imhoff

2018-01-01

Full Text Available Two different photosystems for performing bacteriochlorophyll-mediated photosynthetic energy conversion are employed in different bacterial phyla. Those bacteria employing a photosystem II type of photosynthetic apparatus include the phototrophic purple bacteria (Proteobacteria, Gemmatimonas and Chloroflexus with their photosynthetic relatives. The proteins of the photosynthetic reaction center PufL and PufM are essential components and are common to all bacteria with a type-II photosynthetic apparatus, including the anaerobic as well as the aerobic phototrophic Proteobacteria. Therefore, PufL and PufM proteins and their genes are perfect tools to evaluate the phylogeny of the photosynthetic apparatus and to study the diversity of the bacteria employing this photosystem in nature. Almost complete pufLM gene sequences and the derived protein sequences from 152 type strains and 45 additional strains of phototrophic Proteobacteria employing photosystem II were compared. The results give interesting and comprehensive insights into the phylogeny of the photosynthetic apparatus and clearly define Chromatiales, Rhodobacterales, Sphingomonadales as major groups distinct from other Alphaproteobacteria, from Betaproteobacteria and from Caulobacterales (Brevundimonas subvibrioides. A special relationship exists between the PufLM sequences of those bacteria employing bacteriochlorophyll b instead of bacteriochlorophyll a. A clear phylogenetic association of aerobic phototrophic purple bacteria to anaerobic purple bacteria according to their PufLM sequences is demonstrated indicating multiple evolutionary lines from anaerobic to aerobic phototrophic purple bacteria. The impact of pufLM gene sequences for studies on the environmental diversity of phototrophic bacteria is discussed and the possibility of their identification on the species level in environmental samples is pointed out.

Insight into the Reaction Mechanism of Graphene Oxide with Oxidative Free Radical

Institute of Scientific and Technical Information of China (English)

ZHOU Xuejiao; XU Liangyou

2017-01-01

Graphene oxide(GO),as an important derivative of graphene,could be considered as a super aromatic molecule decorated with a range of reactive oxygen-containing groups on its surface,which endows graphene high reactivity with other molecules.In our previous work,we demonstrated that GO sheets were cut into small pieces(graphene quantum dots,GQDs) by oxidative free radicals(hydroxyl radical HO or oxygen radical [O]) under UV irradiation.It is notable that reactions involving free radicals are influenced by reaction conditions pronouncedly.However,researches on details about reactions of GO with free radicals have not been reported thus far.In this work,the effects of different factors on the photo-Fenton reaction of GO were studied.It is demonstrated that the reaction rate is closely related to the concentration of free radicals.It is speculated that through the optimization of reaction conditions,the reaction of graphene with free radicals could carry out efficiently for further applications.

G-computation demonstration in causal mediation analysis

International Nuclear Information System (INIS)

Wang, Aolin; Arah, Onyebuchi A.

2015-01-01

Recent work has considerably advanced the definition, identification and estimation of controlled direct, and natural direct and indirect effects in causal mediation analysis. Despite the various estimation methods and statistical routines being developed, a unified approach for effect estimation under different effect decomposition scenarios is still needed for epidemiologic research. G-computation offers such unification and has been used for total effect and joint controlled direct effect estimation settings, involving different types of exposure and outcome variables. In this study, we demonstrate the utility of parametric g-computation in estimating various components of the total effect, including (1) natural direct and indirect effects, (2) standard and stochastic controlled direct effects, and (3) reference and mediated interaction effects, using Monte Carlo simulations in standard statistical software. For each study subject, we estimated their nested potential outcomes corresponding to the (mediated) effects of an intervention on the exposure wherein the mediator was allowed to attain the value it would have under a possible counterfactual exposure intervention, under a pre-specified distribution of the mediator independent of any causes, or under a fixed controlled value. A final regression of the potential outcome on the exposure intervention variable was used to compute point estimates and bootstrap was used to obtain confidence intervals. Through contrasting different potential outcomes, this analytical framework provides an intuitive way of estimating effects under the recently introduced 3- and 4-way effect decomposition. This framework can be extended to complex multivariable and longitudinal mediation settings

Nanoscale studies of cement chemistry with 15N resonance reaction analysis

International Nuclear Information System (INIS)

Schweitzer, Jeffrey S.; Livingston, Richard A.; Rolfs, Claus; Becker, Hans-Werner; Kubsky, Stefan; Spillane, Timothy; Castellote, Marta; Viedma, Paloma G. de

2005-01-01

Analyses of materials with ion beams have proven to be a valuable technique for describing the spatial distributions of specific elements in host materials. We have applied this technique using the 15 N(p, αγ) 12 C reaction to study the time dependence of the chemical reactions involved in the curing of cement. By using the Dynamitron Tandem accelerator at the Ruhr Universitaet, Bochum, Germany, we have been able to achieve a few nanometer spatial resolution at the surface of cement grains and to study the hydrogen distributions to a depth of about 2 μm. By applying a technique for stopping the chemical reactions at arbitrary times, the time dependence of the chemical reactions involving specific components of cement can be investigated. In addition, the effects of additives on the chemical reactions have been studied, as have materials that are components of concrete

Functional data analysis on ground reaction force of military load carriage increment

Science.gov (United States)

Din, Wan Rozita Wan; Rambely, Azmin Sham

2014-06-01

Analysis of ground reaction force on military load carriage is done through functional data analysis (FDA) statistical technique. The main objective of the research is to investigate the effect of 10% load increment and to find the maximum suitable load for the Malaysian military. Ten military soldiers age 31 ± 6.2 years, weigh 71.6 ± 10.4 kg and height of 166.3 ± 5.9 cm carrying different military load range from 0% body weight (BW) up to 40% BW participated in an experiment to gather the GRF and kinematic data using Vicon Motion Analysis System, Kirstler force plates and thirty nine body markers. The analysis is conducted in sagittal, medial lateral and anterior posterior planes. The results show that 10% BW load increment has an effect when heel strike and toe-off for all the three planes analyzed with P-value less than 0.001 at 0.05 significant levels. FDA proves to be one of the best statistical techniques in analyzing the functional data. It has the ability to handle filtering, smoothing and curve aligning according to curve features and points of interest.

Spontaneous Hedonic Reactions to Social Media Cues.

Science.gov (United States)

van Koningsbruggen, Guido M; Hartmann, Tilo; Eden, Allison; Veling, Harm

2017-05-01

Why is it so difficult to resist the desire to use social media? One possibility is that frequent social media users possess strong and spontaneous hedonic reactions to social media cues, which, in turn, makes it difficult to resist social media temptations. In two studies (total N = 200), we investigated less-frequent and frequent social media users' spontaneous hedonic reactions to social media cues using the Affect Misattribution Procedure-an implicit measure of affective reactions. Results demonstrated that frequent social media users showed more favorable affective reactions in response to social media (vs. control) cues, whereas less-frequent social media users' affective reactions did not differ between social media and control cues (Studies 1 and 2). Moreover, the spontaneous hedonic reactions to social media (vs. control) cues were related to self-reported cravings to use social media and partially accounted for the link between social media use and social media cravings (Study 2). These findings suggest that frequent social media users' spontaneous hedonic reactions in response to social media cues might contribute to their difficulties in resisting desires to use social media.

SWAAM-LT: The long-term, sodium/water reaction analysis method computer code

International Nuclear Information System (INIS)

Shin, Y.W.; Chung, H.H.; Wiedermann, A.H.; Tanabe, H.

1993-01-01

The SWAAM-LT Code, developed for analysis of long-term effects of sodium/water reactions, is discussed. The theoretical formulation of the code is described, including the introduction of system matrices for ease of computer programming as a general system code. Also, some typical results of the code predictions for available large scale tests are presented. Test data for the steam generator design with the cover-gas feature and without the cover-gas feature are available and analyzed. The capabilities and limitations of the code are then discussed in light of the comparison between the code prediction and the test data

Development of a novel fingerprint for chemical reactions and its application to large-scale reaction classification and similarity.

Science.gov (United States)

Schneider, Nadine; Lowe, Daniel M; Sayle, Roger A; Landrum, Gregory A

2015-01-26

Fingerprint methods applied to molecules have proven to be useful for similarity determination and as inputs to machine-learning models. Here, we present the development of a new fingerprint for chemical reactions and validate its usefulness in building machine-learning models and in similarity assessment. Our final fingerprint is constructed as the difference of the atom-pair fingerprints of products and reactants and includes agents via calculated physicochemical properties. We validated the fingerprints on a large data set of reactions text-mined from granted United States patents from the last 40 years that have been classified using a substructure-based expert system. We applied machine learning to build a 50-class predictive model for reaction-type classification that correctly predicts 97% of the reactions in an external test set. Impressive accuracies were also observed when applying the classifier to reactions from an in-house electronic laboratory notebook. The performance of the novel fingerprint for assessing reaction similarity was evaluated by a cluster analysis that recovered 48 out of 50 of the reaction classes with a median F-score of 0.63 for the clusters. The data sets used for training and primary validation as well as all python scripts required to reproduce the analysis are provided in the Supporting Information.

Tank 241-AX-104 upper vadose zone cone penetrometer demonstration sampling and analysis plan

International Nuclear Information System (INIS)

FIELD, J.G.

1999-01-01

This sampling and analysis plan (SAP) is the primary document describing field and laboratory activities and requirements for the tank 241-AX-104 upper vadose zone cone penetrometer (CP) demonstration. It is written in accordance with Hanford Tank Initiative Tank 241-AX-104 Upper Vadose Zone Demonstration Data Quality Objective (Banning 1999). This technology demonstration, to be conducted at tank 241-AX-104, is being performed by the Hanford Tanks Initiative (HTI) Project as a part of Tank Waste Remediation System (TWRS) Retrieval Program (EM-30) and the Office of Science and Technology (EM-50) Tanks Focus Area. Sample results obtained as part of this demonstration will provide additional information for subsequent revisions to the Retrieval Performance Evaluation (RPE) report (Jacobs 1998). The RPE Report is the result of an evaluation of a single tank farm (AX Tank Farm) used as the basis for demonstrating a methodology for developing the data and analyses necessary to support making tank waste retrieval decisions within the context of tank farm closure requirements. The RPE includes a study of vadose zone contaminant transport mechanisms, including analysis of projected tank leak characteristics, hydrogeologic characteristics of tank farm soils, and the observed distribution of contaminants in the vadose zone in the tank farms. With limited characterization information available, large uncertainties exist as to the nature and extent of contaminants that may exist in the upper vadose zone in the AX Tank Farm. Traditionally, data has been collected from soils in the vadose zone through the installation of boreholes and wells. Soil samples are collected as the bore hole is advanced and samples are screened on site and/or sent to a laboratory for analysis. Some in-situ geophysical methods of contaminant analysis can be used to evaluate radionuclide levels in the soils adjacent to an existing borehole. However, geophysical methods require compensation for well

Improving Your Exploratory Factor Analysis for Ordinal Data: A Demonstration Using FACTOR

Directory of Open Access Journals (Sweden)

James Baglin

2014-06-01

Full Text Available Exploratory factor analysis (EFA methods are used extensively in the field of assessment and evaluation. Due to EFA's widespread use, common methods and practices have come under close scrutiny. A substantial body of literature has been compiled highlighting problems with many of the methods and practices used in EFA, and, in response, many guidelines have been proposed with the aim to improve application. Unfortunately, implementing recommended EFA practices has been restricted by the range of options available in commercial statistical packages and, perhaps, due to an absence of clear, practical - how-to' demonstrations. Consequently, this article describes the application of methods recommended to get the most out of your EFA. The article focuses on dealing with the common situation of analysing ordinal data as derived from Likert-type scales. These methods are demonstrated using the free, stand-alone, easy-to-use and powerful EFA package FACTOR (http://psico.fcep.urv.es/utilitats/factor/, Lorenzo-Seva & Ferrando, 2006. The demonstration applies the recommended techniques using an accompanying dataset, based on the Big 5 personality test. The outcomes obtained by the EFA using the recommended procedures through FACTOR are compared to the default techniques currently available in SPSS.

Unexpected Reaction Pathway for butyrylcholinesterase-catalyzed inactivation of “hunger hormone” ghrelin

Science.gov (United States)

Yao, Jianzhuang; Yuan, Yaxia; Zheng, Fang; Zhan, Chang-Guo

2016-02-01

Extensive computational modeling and simulations have been carried out, in the present study, to uncover the fundamental reaction pathway for butyrylcholinesterase (BChE)-catalyzed hydrolysis of ghrelin, demonstrating that the acylation process of BChE-catalyzed hydrolysis of ghrelin follows an unprecedented single-step reaction pathway and the single-step acylation process is rate-determining. The free energy barrier (18.8 kcal/mol) calculated for the rate-determining step is reasonably close to the experimentally-derived free energy barrier (~19.4 kcal/mol), suggesting that the obtained mechanistic insights are reasonable. The single-step reaction pathway for the acylation is remarkably different from the well-known two-step acylation reaction pathway for numerous ester hydrolysis reactions catalyzed by a serine esterase. This is the first time demonstrating that a single-step reaction pathway is possible for an ester hydrolysis reaction catalyzed by a serine esterase and, therefore, one no longer can simply assume that the acylation process must follow the well-known two-step reaction pathway.

Compositional analysis of sulfated polysaccharides from sea cucumber (Stichopus japonicus) released by autolysis reaction.

Science.gov (United States)

Song, Shuang; Wu, Sufeng; Ai, Chunqing; Xu, Xin; Zhu, Zhenjun; Cao, Chunyang; Yang, Jingfeng; Wen, Chengrong

2018-07-15

Autolysis is not only a major reason for postharvest quality deterioration of sea cucumber, but also a promising alternative for exogenous protease to produce peptides or polysaccharides. However, little has been known about the effects of autolysis on bioactive polysaccharides of sea cucumber. Concerning the quality and safety of sea cucumber products involved autolysis reaction, the present study focused on the chemical composition of sulfated polysaccharides (SPs) released by autolysis reaction. Chemical analysis indicated that after 3-day autolysis 63% of sulfated polysaccharides were liberated but with protein chains at their reducing ends. Then the composition of SP obtained by autolysis (A-SP) was compared with that of total SPs (T-SP) via a series of analysis techniques, including FTIR, 1 H NMR, HPLC and mass spectroscopy. As indicated by the results, fucan to fucosylated chondroitin sulfate ratio was found high in A-SP compared to T-SP, fucan with a lower molecular weight was the major fraction in A-SP, and the di-sulfated Fuc residue observed in T-SP was absent in A-SP. To conclude, A-SP differed greatly from T-SP in the chemical composition, suggesting possible changes on their bioactivities. Copyright © 2018. Published by Elsevier B.V.

Simultaneous analysis of multiple T helper subsets in leprosy reveals distinct patterns of Th1, Th2, Th17 and Tregs markers expression in clinical forms and reactional events.

Science.gov (United States)

Azevedo, Michelle de Campos Soriani; Marques, Heloisa; Binelli, Larissa Sarri; Malange, Mariana Silva Vieira; Devides, Amanda Carreira; Silva, Eliane Aparecida; Fachin, Luciana Raquel Vincenzi; Ghidella, Cassio Cesar; Soares, Cleverson Teixeira; Garlet, Gustavo Pompermaier; Rosa, Patrícia Sammarco; Belone, Andrea de Farias Fernandes; Trombone, Ana Paula Favaro

2017-12-01

Leprosy is a chronic infectious disease caused by Mycobacterium leprae. Previous studies have demonstrated that the difference among clinical forms of leprosy can be associated with the immune response of patients, mainly by T helper (Th) and regulatory T cells (Tregs). Then, aiming at clarifying the immune response, the expression of cytokines related to Th1, Th2, Th17 and Tregs profiles were evaluated by qPCR in 87 skin biopsies from leprosy patients. Additionally, cytokines and anti-PGL-1 antibodies were determined in serum by ELISA. The results showed that the expression of various targets (mRNA) related to Th1, Th2, Th17 and Tregs were significantly modulated in leprosy when compared with healthy individuals, suggesting the presence of a mixed profile. In addition, the targets related to Th1 predominated in the tuberculoid pole and side and Th2 and Tregs predominated in the lepromatous pole and side; however, Th17 targets showed a mixed profile. Concerning reactional events, Tregs markers were decreased and IL-15 was increased in reversal reaction and IL-17F, CCL20 and IL-8 in erythema nodosum leprosum, when compared with the respective non-reactional leprosy patients. Additionally, ELISA analysis demonstrated that IL-22, IL-6, IL-10 and anti-PGL-1 antibody levels were significantly higher in the serum of patients when compared with healthy individuals, and IL-10 and anti-PGL-1 antibodies were also increased in the lepromatous pole and side. Together, these results indicate that Th1, Th2 and Th17 are involved in the determination of clinical forms of leprosy and suggest that decreased Tregs activity may be involved in the pathogenesis of reactional events.

Consequence analysis of IWTS metal water reactions (Fauske and Associates report 99-35)

International Nuclear Information System (INIS)

DUNCAN, D.R.

1999-01-01

The report describes the consequences of postulated thermally unstable conditions in the IWTS knock out pot. The consequence analysis shows that both the knock out pot and particulate bed will stay intact, and that releases will be minor. Reaction rate limitations prevent knock out pot pressure and/or temperature from even approaching values that would threaten structural integrity. Source term calculations based on a particle bed with a homogeneous mixture of metal and oxide particles yield a release above the K Basin pool of about 12 grams

In Situ Monitoring of Chemical Reactions at a Solid-Water Interface by Femtosecond Acoustics.

Science.gov (United States)

Shen, Chih-Chiang; Weng, Meng-Yu; Sheu, Jinn-Kong; Yao, Yi-Ting; Sun, Chi-Kuang

2017-11-02

Chemical reactions at a solid-liquid interface are of fundamental importance. Interfacial chemical reactions occur not only at the very interface but also in the subsurface area, while existing monitoring techniques either provide limited spatial resolution or are applicable only for the outmost atomic layer. Here, with the aid of the time-domain analysis with femtosecond acoustics, we demonstrate a subatomic-level-resolution technique to longitudinally monitor chemical reactions at solid-water interfaces, capable of in situ monitoring even the subsurface area under atmospheric conditions. Our work was proven by monitoring the already-known anode oxidation process occurring during photoelectrochemical water splitting. Furthermore, whenever the oxide layer thickness equals an integer  number of the effective atomic layer thickness, the measured acoustic echo will show higher signal-to-noise ratios with reduced speckle noise, indicating the quantum-like behavior of this coherent-phonon-based technique.

Thermodynamic stability of elementary chemical reactions proceeding at finite rates revisited using Lyapunov function analysis

International Nuclear Information System (INIS)

Burande, Chandrakant S.; Bhalekar, Anil A.

2005-01-01

The thermodynamic stability of a few representative elementary chemical reactions proceeding at finite rates has been investigated using the recently proposed thermodynamic Lyapunov function and following the steps of Lyapunov's second method (also termed as the direct method) of stability of motion. The thermodynamic Lyapunov function; L s , used herein is the excess rate of entropy production in the thermodynamic perturbation space, which thereby inherits the dictates of the second law of thermodynamics. This Lyapunov function is not the same as the excess entropy rate that one encounters in thermodynamic (irreversible) literature. The model chemical conversions studied in this presentation are A+B→v x X and A+B↔ν x X. For the sake of simplicity, the thermal effects of chemical reactions have been considered as not adding to the perturbation as our main aim was to demonstrate how one should use systematically the proposed thermodynamic Lyapunov function following the steps of Lyapunov's second method of stability of motion. The domains of thermodynamic stability under the constantly acting small disturbances, thermodynamic asymptotic stability and thermodynamic instability in these model systems get established

Variation in reaction norms: Statistical considerations and biological interpretation.

Science.gov (United States)

Morrissey, Michael B; Liefting, Maartje

2016-09-01

Analysis of reaction norms, the functions by which the phenotype produced by a given genotype depends on the environment, is critical to studying many aspects of phenotypic evolution. Different techniques are available for quantifying different aspects of reaction norm variation. We examine what biological inferences can be drawn from some of the more readily applicable analyses for studying reaction norms. We adopt a strongly biologically motivated view, but draw on statistical theory to highlight strengths and drawbacks of different techniques. In particular, consideration of some formal statistical theory leads to revision of some recently, and forcefully, advocated opinions on reaction norm analysis. We clarify what simple analysis of the slope between mean phenotype in two environments can tell us about reaction norms, explore the conditions under which polynomial regression can provide robust inferences about reaction norm shape, and explore how different existing approaches may be used to draw inferences about variation in reaction norm shape. We show how mixed model-based approaches can provide more robust inferences than more commonly used multistep statistical approaches, and derive new metrics of the relative importance of variation in reaction norm intercepts, slopes, and curvatures. © 2016 The Author(s). Evolution © 2016 The Society for the Study of Evolution.

Numerical analysis for Darcy-Forchheimer flow in presence of homogeneous-heterogeneous reactions

Directory of Open Access Journals (Sweden)

Muhammad Ijaz Khan

Full Text Available A mathematical study is presented to investigate the influences of homogeneous and heterogeneous reactions in local similar flow caused by stretching sheet with a non-linear velocity and variable thickness. Porous medium effects are characterized by using Darcy-Forchheimer porous-media. A simple isothermal model of homogeneous-heterogeneous reactions is used. The multiphysical boundary value problem is dictated by ten thermophysical parameters: ratio of mass diffusion coefficients, Prandtl number, local inertia coefficient parameter, inverse Darcy number, shape parameter, surface thickness parameter, Hartman number, Homogeneous heat reaction, strength of homogeneous-heterogeneous reactions and Schmidt number. Resulting systems are computed by Runge-Kutta-Fehlberg method. Different shapes of velocity are noticed for n > 1 and n < 1. Keywords: Homogeneous-heterogeneous reactions, Non Darcy porous medium, Variable sheet thickness, Homogeneous heat reaction with stoichiometric coefficient, Runge-Kutta-Fehlberg method

Immunological aspects of nonimmediate reactions to beta-lactam antibiotics.

Science.gov (United States)

Rodilla, Esther Morena; González, Ignacio Dávila; Yges, Elena Laffond; Bellido, Francisco Javier Múñoz; Bara, María Teresa Gracia; Toledano, Félix Lorente

2010-09-01

beta-lactam antibiotics are the agents most frequently implied in immune drug adverse reactions. These can be classified as immediate or nonimmediate according to the time interval between the last drug administration and their onset. Mechanisms of immediate IgE-mediated reactions are widely studied and are therefore better understood. Nonimmediate reactions include a broad number of clinical entities like mild maculopapular exanthemas, the most common, and other less frequent but more severe reactions such as Stevens-Johnson syndrome, toxic epidermal necrolysis, acute exanthematic pustulosis or cytopenias. These nonimmediate reactions are mainly mediated by T cells but the precise underlying mechanisms are not well elucidated. This fact complicates the allergological evaluation of patients with this type of reaction and available tests have demonstrated poor sensitivity and specificity.

Cascade enzymatic reactions for efficient carbon sequestration.

Science.gov (United States)

Xia, Shunxiang; Zhao, Xueyan; Frigo-Vaz, Benjamin; Zheng, Wenyun; Kim, Jungbae; Wang, Ping

2015-04-01

Thermochemical processes developed for carbon capture and storage (CCS) offer high carbon capture capacities, but are generally hampered by low energy efficiency. Reversible cascade enzyme reactions are examined in this work for energy-efficient carbon sequestration. By integrating the reactions of two key enzymes of RTCA cycle, isocitrate dehydrogenase and aconitase, we demonstrate that intensified carbon capture can be realized through such cascade enzymatic reactions. Experiments show that enhanced thermodynamic driving force for carbon conversion can be attained via pH control under ambient conditions, and that the cascade reactions have the potential to capture 0.5 mol carbon at pH 6 for each mole of substrate applied. Overall it manifests that the carbon capture capacity of biocatalytic reactions, in addition to be energy efficient, can also be ultimately intensified to approach those realized with chemical absorbents such as MEA. Copyright © 2015 Elsevier Ltd. All rights reserved.

Analysis of acoustic data from UK sodium/water reaction test facilities

International Nuclear Information System (INIS)

Rowley, R.; Mcknight, J.A.; Airey, J.

1990-01-01

This paper describes acoustic measurements made during a number of sodium/water reaction experiments in the UK. The tests have included water and steam injections through both realistic (fatigue crack) defects and machined orifices and have covered a range of experimental conditions including those appropriate to the inlet and outlet regions of the EFR steam generators. Injection rates were typically in the range 0.1 to 30 g/s. Where possible, gas injections were also included in the test programme for comparison, since it is anticipated that a practical SGU acoustic leak detection system would include a facility for gas injections to allow system calibration, and to confirm transmission properties within the SGU. The test sections were instrumented with accelerometers on waveguides and in some cases included an under-sodium microphone situated about 300mm above the reaction zone. Tape recordings were made during the tests and used for detailed analysis off-line, although an audible output from one of the acoustic channels was used to monitor the progress of the injections and provide information for the rig operators. A comparison of the signal amplitudes measured during the experiments with typical reactor background noise was made and an estimate of the detection sensitivity of an acoustic monitoring system was deduced. 3 refs, 5 figs, 1 tab

Ambulatory Measurement of Ground Reaction Forces

NARCIS (Netherlands)

Veltink, Peter H.; Liedtke, Christian; Droog, Ed

2004-01-01

The measurement of ground reaction forces is important in the biomechanical analysis of gait and other motor activities. It is the purpose of this study to show the feasibility of ambulatory measurement of ground reaction forces using two six degrees of freedom sensors mounted under the shoe. One

Chemical boundary layers in CVD II. Reversible reactions

NARCIS (Netherlands)

Croon, de M.H.J.M.; Giling, L.J.

1990-01-01

In addition to irreversible reactions, which were treated in part I, reversible reactions in the gas phase have beenstudied using the concept of the chemical boundary layer. The analysis is given for the situations in which either the forwardor the back reaction is dominant. Two conceptual models

Chemical reactions confined within carbon nanotubes.

Science.gov (United States)

Miners, Scott A; Rance, Graham A; Khlobystov, Andrei N

2016-08-22

In this critical review, we survey the wide range of chemical reactions that have been confined within carbon nanotubes, particularly emphasising how the pairwise interactions between the catalysts, reactants, transition states and products of a particular molecular transformation with the host nanotube can be used to control the yields and distributions of products of chemical reactions. We demonstrate that nanoscale confinement within carbon nanotubes enables the control of catalyst activity, morphology and stability, influences the local concentration of reactants and products thus affecting equilibria, rates and selectivity, pre-arranges the reactants for desired reactions and alters the relative stability of isomeric products. We critically evaluate the relative advantages and disadvantages of the confinement of chemical reactions inside carbon nanotubes from a chemical perspective and describe how further developments in the controlled synthesis of carbon nanotubes and the incorporation of multifunctionality are essential for the development of this ever-expanding field, ultimately leading to the effective control of the pathways of chemical reactions through the rational design of multi-functional carbon nanoreactors.

Determination of transport and reaction swarm coefficients from the analysis of complex transient pulses from the pulsed Townsend experiment

International Nuclear Information System (INIS)

Bekstein, A; De Urquijo, J; Rodríguez-Luna, J C; Juárez, A M; Ducasse, O

2012-01-01

We present in this paper the interpretation and analysis of transient pulses from a pulsed Townsend experiment by solving the continuity equations of the charged carriers (electrons and ions) involved in the avalanche. The set of second order partial differential equations is solved by SIMAV, a simulator designed specifically for the pulsed Townsend avalanche. Complex situations involving processes such as electron detachment, ion-molecule reactions, Penning ionization and secondary electron emission from ion impact at the cathode, virtually impossible to solve analytically, are discussed here to illustrate the capability of the simulator to help explain the various reaction processes involved in the avalanche, and also to derive some of the transport and reaction coefficients.

Sequential capillary electrophoresis analysis using optically gated sample injection and UV/vis detection.

Science.gov (United States)

Liu, Xiaoxia; Tian, Miaomiao; Camara, Mohamed Amara; Guo, Liping; Yang, Li

2015-10-01

We present sequential CE analysis of amino acids and L-asparaginase-catalyzed enzyme reaction, by combing the on-line derivatization, optically gated (OG) injection and commercial-available UV-Vis detection. Various experimental conditions for sequential OG-UV/vis CE analysis were investigated and optimized by analyzing a standard mixture of amino acids. High reproducibility of the sequential CE analysis was demonstrated with RSD values (n = 20) of 2.23, 2.57, and 0.70% for peak heights, peak areas, and migration times, respectively, and the LOD of 5.0 μM (for asparagine) and 2.0 μM (for aspartic acid) were obtained. With the application of the OG-UV/vis CE analysis, sequential online CE enzyme assay of L-asparaginase-catalyzed enzyme reaction was carried out by automatically and continuously monitoring the substrate consumption and the product formation every 12 s from the beginning to the end of the reaction. The Michaelis constants for the reaction were obtained and were found to be in good agreement with the results of traditional off-line enzyme assays. The study demonstrated the feasibility and reliability of integrating the OG injection with UV/vis detection for sequential online CE analysis, which could be of potential value for online monitoring various chemical reaction and bioprocesses. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tuning Catalytic Performance through a Single or Sequential Post-Synthesis Reaction(s) in a Gas Phase

Energy Technology Data Exchange (ETDEWEB)

Shan, Junjun [Department; Department; Zhang, Shiran [Department; Department; Choksi, Tej [Department; Nguyen, Luan [Department; Department; Bonifacio, Cecile S. [Department; Li, Yuanyuan [Department; Zhu, Wei [Department; Department; College; Tang, Yu [Department; Department; Zhang, Yawen [College; Yang, Judith C. [Department; Greeley, Jeffrey [Department; Frenkel, Anatoly I. [Department; Tao, Franklin [Department; Department

2016-12-05

Catalytic performance of a bimetallic catalyst is determined by geometric structure and electronic state of the surface or even the near-surface region of the catalyst. Here we report that single and sequential postsynthesis reactions of an as-synthesized bimetallic nanoparticle catalyst in one or more gas phases can tailor surface chemistry and structure of the catalyst in a gas phase, by which catalytic performance of this bimetallic catalyst can be tuned. Pt–Cu regular nanocube (Pt–Cu RNC) and concave nanocube (Pt–Cu CNC) are chosen as models of bimetallic catalysts. Surface chemistry and catalyst structure under different reaction conditions and during catalysis were explored in gas phase of one or two reactants with ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) and extended X-ray absorption fine structure (EXAFS) spectroscopy. The newly formed surface structures of Pt–Cu RNC and Pt–Cu CNC catalysts strongly depend on the reactive gas(es) used in the postsynthesis reaction(s). A reaction of Pt–Cu RNC-as synthesized with H2 at 200 °C generates a near-surface alloy consisting of a Pt skin layer, a Cu-rich subsurface, and a Pt-rich deep layer. This near-surface alloy of Pt–Cu RNC-as synthesized-H2 exhibits a much higher catalytic activity in CO oxidation in terms of a low activation barrier of 39 ± 4 kJ/mol in contrast to 128 ± 7 kJ/mol of Pt–Cu RNC-as synthesized. Here the significant decrease of activation barrier demonstrates a method to tune catalytic performances of as-synthesized bimetallic catalysts. A further reaction of Pt–Cu RNC-as synthesized-H2 with CO forms a Pt–Cu alloy surface, which exhibits quite different catalytic performance in CO oxidation. It suggests the capability of generating a different surface by using another gas. The capability of tuning surface chemistry and structure of bimetallic catalysts was also demonstrated in restructuring of Pt–Cu CNC-as synthesized.

C-13 isotopic studies of the surface catalysed reactions of methane

International Nuclear Information System (INIS)

Long, M.A.; He, S.J.X.; Adebajo, M.

1997-01-01

The ability of methane to methylate aromatic compounds, which are considered to be models for coal, is being studied. Related to this reaction, but at higher temperatures, is the direct formation of benzene from methane in the presence of these catalysts. Controversy exists in the literature on the former reaction, and 13 C isotope studies are being used to resolve the question. The interest in this reaction arises because the utilisation of methane, in the form of natural gas, in place of hydrogen for direct coal liquefaction would have major economic advantage. For this reason Isotope studies in this area have contributed significantly to an understanding of the methylation reactions. The paper describes experiments utilising methane 13 C, which show that methylation of aromatics such as naphthalene by the methane 13 C is catalysed by microporous, Cu-exchanged SAPO-5, at elevated pressures (6.8 MPa) and temperatures around 400 degree C. The mass spectrometric analysis and n.m.r. study of the isotopic composition of the products of the methylation reaction demonstrate unequivocally that methane provides the additional carbon atom for the methylated products. Thermodynamic calculations predict that the reaction is favourable at high methane pressures under these experimental conditions. The mechanism as suggested by the isotope study is discussed. The catalysts which show activity for the activation of methane for direct methylation of organic compounds, such as naphthalene, toluene, phenol and pyrene, are substituted aluminophosphate molecular sieves, EIAPO-5 (where El=Pb, Cu, Ni and Si) and a number of metal substituted zeolites. Our earlier tritium studies had shown that these catalysts will activate alkanes, at least as far as isotope hydrogen exchange reactions are concerned

[Electromagnetic studies of nuclear structure and reactions

International Nuclear Information System (INIS)

1992-01-01

The experimental goals are focused on developing an understanding of strong interactions and the structure of hadronic systems by determination of the electromagnetic response; these goals will be accomplished through coincidence detection of final states. Nuclear modeling objectives are to organize and interpret the data through a consistent description of a broad spectrum of reaction observables; calculations are performed in a nonrelativistic diagrammatic framework as well as a relativistic QHD approach. Work is described according to the following arrangement: direct knockout reactions (completion of 16 O(e,e'p), 12 C(e,e'pp) progress, large acceptance detector physics simulations), giant resonance studies (intermediate-energy experiments with solid-state detectors, the third response function in 12 C(e,e'p 0 ) and 16 O(e,e'p 0 ), comparison of the 12 C(e, e'p 0 ) and 16 O(e,e'p 3 ) reactions, quadrupole strength in the 16 O(e,e'α 0 ) reaction, quadrupole strength in the 12 C(e,e'α) reaction, analysis of the 12 C(e,e'p 1 ) and 16 O(e,e'p 3 ) angular distributions, analysis of the 40 Ca(e,e'x) reaction at low q, analysis of the higher-q 12 C(e,e'x) data from Bates), models of nuclear structure (experimental work, Hartree-Fock calculations, phonon excitations in spherical nuclei, shell model calculations, variational methods for relativistic fields), and instrumentation development efforts (developments at CEBAF, CLAS contracts, BLAST developments)

Reaction mechanism of reductive decomposition of FGD gypsum with anthracite

International Nuclear Information System (INIS)

Zheng, Da; Lu, Hailin; Sun, Xiuyun; Liu, Xiaodong; Han, Weiqing; Wang, Lianjun

2013-01-01

Highlights: • The reaction mechanism was different if the molar ratio of C/CaSO 4 was different. • The yield of CaO rises with an increase in temperature. • The optimal ratio of C/CaSO 4 = 1.2:1. • The decomposition process is mainly apparent solid–solid reaction with liquid-phase involved. - Abstract: The process of decomposition reaction between flue gas desulfurization (FGD) gypsum and anthracite is complex, which depends on the reaction conditions and atmosphere. In this study, thermogravimetric analysis with Fourier transform infrared spectroscopy (TGA-FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and the experiment in a tubular reactor were used to characterize the decomposition reaction in a nitrogen atmosphere under different conditions. The reaction mechanism analysis showed that the decomposition reaction process and mechanism were different when the molar proportion of C/CaSO 4 was changed. The experiment results showed that appropriate increase in the C/CaSO 4 proportion and higher temperatures were suitable for the formation of the main production of CaO, which can help us to understand the solid state reaction mechanism better. Via kinetic analysis of the reaction between anthracite and FGD gypsum under the optimal molar ratio of C/CaSO 4 , the mechanism model of the reaction was confirmed and the decomposition process was a two-step reaction which was in accordance with apparent solid–solid reaction

Nuclear reaction analysis (NRA) for trace element detection

Energy Technology Data Exchange (ETDEWEB)

Doebeli, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Noll, K. [Bern Univ. (Switzerland)

1997-09-01

Ion beam induced nuclear reactions can be used to analyse trace element concentrations in materials. The method is especially suited for the detection of light contaminants in heavy matrices. (author) 3 figs., 2 refs.

Analysis of Native-Like Proteins and Protein Complexes Using Cation to Anion Proton Transfer Reactions (CAPTR)

Science.gov (United States)

Laszlo, Kenneth J.; Bush, Matthew F.

2015-12-01

Mass spectra of native-like protein complexes often exhibit narrow charge-state distributions, broad peaks, and contributions from multiple, coexisting species. These factors can make it challenging to interpret those spectra, particularly for mixtures with significant heterogeneity. Here we demonstrate the use of ion/ion proton transfer reactions to reduce the charge states of m/ z-selected, native-like ions of proteins and protein complexes, a technique that we refer to as cation to anion proton transfer reactions (CAPTR). We then demonstrate that CAPTR can increase the accuracy of charge state assignments and the resolution of interfering species in native mass spectrometry. The CAPTR product ion spectra for pyruvate kinase exhibit ~30 peaks and enable unambiguous determination of the charge state of each peak, whereas the corresponding precursor spectra exhibit ~6 peaks and the assigned charge states have an uncertainty of ±3%. 15+ bovine serum albumin and 21+ yeast enolase dimer both appear near m/ z 4450 and are completely unresolved in a mixture. After a single CAPTR event, the resulting product ions are baseline resolved. The separation of the product ions increases dramatically after each subsequent CAPTR event; 12 events resulted in a 3000-fold improvement in separation relative to the precursor ions. Finally, we introduce a framework for interpreting and predicting the figures of merit for CAPTR experiments. More generally, these results suggest that CAPTR strongly complements other mass spectrometry tools for analyzing proteins and protein complexes, particularly those in mixtures.

Component Analysis of Sweet BV and Clinical Trial on Antibody Titer and Allergic Reactions

OpenAIRE

Ki Rok, Kwon; Suk Ho, Choi; Bae Chun Cha

2006-01-01

Objectives : The aim of this study was to observe prevention of allergic reactions of Sweet Bee Venom (removing enzyme components from Bee Venom). Methods : Content analysis of Sweet Bee Venom and Bee Venom was rendered using HPLC method and characterization of Anti-Sweet Bee Venom in Rabbit Serum. Clinical observation was conducted for inducement of allergic responses to Sweet BV. Results : 1. Analyzing melittin content using HPLC, Sweet BV contained 34.9% more melittin than Bee venom ...

Integration of On-Column Chemical Reactions in Protein Characterization by Liquid Chromatography/Mass Spectrometry: Cross-Path Reactive Chromatography.

Science.gov (United States)

Pawlowski, Jake W; Carrick, Ian; Kaltashov, Igor A

2018-01-16

Profiling of complex proteins by means of mass spectrometry (MS) frequently requires that certain chemical modifications of their covalent structure (e.g., reduction of disulfide bonds), be carried out prior to the MS or MS/MS analysis. Traditionally, these chemical reactions take place in the off-line mode to allow the excess reagents (the majority of which interfere with the MS measurements and degrade the analytical signal) to be removed from the protein solution prior to MS measurements. In addition to a significant increase in the analysis time, chemical reactions may result in a partial or full loss of the protein if the modifications adversely affect its stability, e.g,, making it prone to aggregation. In this work we present a new approach to solving this problem by carrying out the chemical reactions online using the reactive chromatography scheme on a size exclusion chromatography (SEC) platform with MS detection. This is achieved by using a cross-path reaction scheme, i.e., by delaying the protein injection onto the SEC column (with respect to the injection of the reagent plug containing a disulfide-reducing agent), which allows the chemical reactions to be carried out inside the column for a limited (and precisely controlled) period of time, while the two plugs overlap inside the column. The reduced protein elutes separately from the unconsumed reagents, allowing the signal suppression in ESI to be avoided and enabling sensitive MS detection. The new method is used to measure fucosylation levels of a plasma protein haptoglobin at the whole protein level following online reduction of disulfide-linked tetrameric species to monomeric units. The feasibility of top-down fragmentation of disulfide-containing proteins is also demonstrated using β 2 -microglobulin and a monoclonal antibody (mAb). The new online technique is both robust and versatile, as the cross-path scheme can be readily expanded to include multiple reactions in a single experiment (as

Automated Prediction of Catalytic Mechanism and Rate Law Using Graph-Based Reaction Path Sampling.

Science.gov (United States)

Habershon, Scott

2016-04-12

In a recent article [ J. Chem. Phys. 2015 , 143 , 094106 ], we introduced a novel graph-based sampling scheme which can be used to generate chemical reaction paths in many-atom systems in an efficient and highly automated manner. The main goal of this work is to demonstrate how this approach, when combined with direct kinetic modeling, can be used to determine the mechanism and phenomenological rate law of a complex catalytic cycle, namely cobalt-catalyzed hydroformylation of ethene. Our graph-based sampling scheme generates 31 unique chemical products and 32 unique chemical reaction pathways; these sampled structures and reaction paths enable automated construction of a kinetic network model of the catalytic system when combined with density functional theory (DFT) calculations of free energies and resultant transition-state theory rate constants. Direct simulations of this kinetic network across a range of initial reactant concentrations enables determination of both the reaction mechanism and the associated rate law in an automated fashion, without the need for either presupposing a mechanism or making steady-state approximations in kinetic analysis. Most importantly, we find that the reaction mechanism which emerges from these simulations is exactly that originally proposed by Heck and Breslow; furthermore, the simulated rate law is also consistent with previous experimental and computational studies, exhibiting a complex dependence on carbon monoxide pressure. While the inherent errors of using DFT simulations to model chemical reactivity limit the quantitative accuracy of our calculated rates, this work confirms that our automated simulation strategy enables direct analysis of catalytic mechanisms from first principles.

Supplement analysis 2 of environmental impacts resulting from modifications in the West Valley Demonstration Project

International Nuclear Information System (INIS)

1998-01-01

The West Valley Demonstration Project, located in western New York, has approximately 600,000 gallons of liquid high-level radioactive waste (HLW) in storage in underground tanks. While corrosion analysis has revealed that only limited tank degradation has taken place, the failure of these tanks could release HLW to the environment. Congress requires DOE to demonstrate the technology for removal and solidification of HLW. DOE issued the Final Environmental Impact Statement (FEIS) in 1982. The purpose of this second supplement analysis is to re-assess the 1982 Final Environmental Impact Statement's continued adequacy. This report provides the necessary and appropriate data for DOE to determine whether the environmental impacts presented by the ongoing refinements in the design, process, and operations of the Project are considered sufficiently bounded within the envelope of impacts presented in the FEIS and supporting documentation

Analysis of ping-pong reaction mechanisms by positional isotope exchange. Application to galactose-1-phosphate uridyltransferase

International Nuclear Information System (INIS)

Hester, L.S.; Raushel, F.M.

1987-01-01

A new positional isotope exchange method has been developed that can be used for the analysis of enzyme-catalyzed reactions which have ping-pong kinetic mechanisms. The technique can be used to measure the relative rates of ligand dissociation from enzyme-product complexes. Enzyme is incubated with the labeled substrate and an excess of the corresponding unlabeled product. The partitioning of the enzyme-product complex back toward free enzyme is determined from the rate of positional isotope exchange within the original labeled substrate. The partitioning of the enzyme-product complex forward toward free enzyme is determined from the rate of formation of totally unlabeled substrate. It has been shown that the ratio of the two rates provides a lower limit for the release of product from the enzyme-product complex. The technique has been applied to the reaction catalyzed by galactose-1-phosphate uridyltransferase. The lower limit for the release of glucose 1-phosphate from the uridyl-enzyme relative to the maximal velocity of the reverse reaction was determined to be 3.4 +/- 0.5

Test analysis and research on static choice reaction ability of commercial vehicle drivers

Science.gov (United States)

Zhang, Lingchao; Wei, Lang; Qiao, Jie; Tian, Shun; Wang, Shengchang

2017-03-01

Drivers' choice reaction ability has a certain relation with safe driving. It has important significance to research its influence on traffic safety. Firstly, the paper uses a choice reaction detector developed by research group to detect drivers' choice reaction ability of commercial vehicles, and gets 2641 effective samples. Then by using mathematical statistics method, the paper founds that average reaction time from accident group has no difference with non-accident group, and then introduces a variance rate of reaction time as a new index to replace it. The result shows that the test index choice reaction errors and variance rate of reaction time have positive correlations with accidents. Finally, according to testing results of the detector, the paper formulates a detection threshold with four levels for helping transportation companies to assess commercial vehicles drivers.

In Vivo Lighted Fluorescence via Fenton Reaction: Approach for Imaging of Hydrogen Peroxide in Living Systems.

Science.gov (United States)

Liu, Changhui; Chen, Weiju; Qing, Zhihe; Zheng, Jing; Xiao, Yue; Yang, Sheng; Wang, Lili; Li, Yinhui; Yang, Ronghua

2016-04-05

By virtue of its high sensitivity and rapidity, Fenton reaction has been demonstrated as a powerful tool for in vitro biochemical analysis; however, in vivo applications of Fenton reaction still remain to be exploited. Herein, we report, for the first time, the design, formation and testing of Fenton reaction for in vivo fluorescence imaging of hydrogen peroxide (H2O2). To realize in vivo fluorescence imaging of H2O2 via Fenton reaction, a functional nanosphere, Fc@MSN-FDNA/PTAD, is fabricated from mesoporous silica nanoparticle (MSN), a Fenton reagent of ferrocene (Fc), ROX-labeled DNA (FDNA), and a cationic perylene derivative (PTAD). The ferrocene molecules are locked in the pore entrances of MSN, and exterior of MSN is covalently immobilized with FDNA. As a key part, PTAD acts as not only the gatekeeper of MSN but also the efficient quencher of ROX. H2O2 can permeate into the nanosphere and react with ferrocene to product hydroxyl radical (·OH) via Fenton reaction, which cleaves FDNA to detach ROX from PTAD, thus in turn, lights the ROX fluorescence. Under physiological condition, H2O2 can be determined from 5.0 nM to 1.0 μM with a detection limit of 2.4 nM. Because of the rapid kinetics of Fenton reaction and high specificity for H2O2, the proposed method meets the requirement for real applications. The feasibility of Fc@MSN-FDNA/PTAD for in vivo applications is demonstrated for fluorescence imaging of exogenous and endogenous H2O2 in cells and mice. We expect that this work will not only contribute to the H2O2-releated studies but also open up a new way to exploit in vivo Fenton reaction for biochemical research.

Catalytic Depolymerization of Lignin and Woody Biomass in Supercritical Ethanol: Influence of Reaction Temperature and Feedstock.

Science.gov (United States)

Huang, Xiaoming; Atay, Ceylanpinar; Zhu, Jiadong; Palstra, Sanne W L; Korányi, Tamás I; Boot, Michael D; Hensen, Emiel J M

2017-11-06

The one-step ethanolysis approach to upgrade lignin to monomeric aromatics using a CuMgAl mixed oxide catalyst is studied in detail. The influence of reaction temperature (200-420 °C) on the product distribution is investigated. At low temperature (200-250 °C), recondensation is dominant, while char-forming reactions become significant at high reaction temperature (>380 °C). At preferred intermediate temperatures (300-340 °C), char-forming reactions are effectively suppressed by alkylation and Guerbet and esterification reactions. This shifts the reaction toward depolymerization, explaining high monomeric aromatics yield. Carbon-14 dating analysis of the lignin residue revealed that a substantial amount of the carbon in the lignin residue originates from reactions of lignin with ethanol. Recycling tests show that the activity of the regenerated catalyst was strongly decreased due to a loss of basic sites due to hydrolysis of the MgO function and a loss of surface area due to spinel oxide formation of the Cu and Al components. The utility of this one-step approach for upgrading woody biomass was also demonstrated. An important observation is that conversion of the native lignin contained in the lignocellulosic matrix is much easier than the conversion of technical lignin.

Analysis of n+165Ho and 169Tm reactions

International Nuclear Information System (INIS)

Young, P.G.; Arthur, E.D.; Philis, C.; Nagel, P.; Collin, M.

1982-09-01

Experimental data for neutron-induced reactions on 165 Ho and 169 Tm have been theoretically analyzed in preparation for calculations on the unstable isotopes of Tm. A set of deformed optical model parameters was determined from measurements of s- and p-wave neutron strength functions, total cross sections, elastic angular distributions, and 16-MeV proton scattering to the 165 Ho ground and first excited states. The parameters for the 165 Ho and 169 Tm nuclei were linked by means of an isospin term in the real and imaginary well depths, together with adjustment of the ν 2 and ν 4 deformation parameters based on systematics in this mass region. Transmission coefficients from this analysis were used in Hauser-Feshbach statistical model calculations of the 169 Tm(n,ν) cross section as well as the 169 Tm(n,2n) and (n,3n) cross sections to 23 MeV, after application of suitable preequilibrium corrections. The results of these calculations are in good agreement with most of the available experimental data on 165 Ho and 169 Tm

Study of the mechanism of Pb + Au reaction at 29 A.MeV; Etude du mecanisme de la reaction Pb + Au a 29 A.MeV

Energy Technology Data Exchange (ETDEWEB)

Aboufirassi, M

1994-07-01

The aim of this thesis is to demonstrate the binary character of Pb + Au reaction at 29 A.MeV and to study the decay modes of very excited nuclei produced. The experiment set up was performed at the GANIL in the scattering chamber NAUTILUS. It was composed by multi detectors of fragments (Z {>=}8) and multi detectors of light charged particles. (Z<8). The analysis of events which lead to detection of more then 80 % of both total charge and total parallel momentum proved that two body final state is still present at this incident energy. This mechanism is similar to the mechanism of heavy ion reaction at low bombarding energy. We have shown that complete damping occurred leading to excitation energy as high as 6 Me V/u. The decay modes of deep inelastic products are evaporation residue or binary fission or multifragmentation. Analysing the fission products, we have estimated the aligned spin of deep inelastic products (45 h). Finally, the study of light charged particles detected with fission fragments has demonstrated that these particles are emitted essentially before fission. The temperature value of hot nuclei emitted at foreword angle is deduced of light particle spectra. (author). 59 refs.

Measurement and analysis of the reaction π-p→π-π+n at 63 GeV incident momentum

International Nuclear Information System (INIS)

Peters, S.C.A.

1980-01-01

The measurement and analysis of the reaction π - p→π - π + n at 63.2 GeV incident momentum is described. The aim of the experiment was to measure the s-dependence of the production mechanism and to search for high spin resonances in the ππ system. (Auth.)

Constant rate thermal analysis of a dehydrogenation reaction

Czech Academy of Sciences Publication Activity Database

Perejon, A.; Perez-Maqueda, L. A.; Sanchez-Jimenez, P.E.; Criado, J. M.; Murafa, Nataliya; Šubrt, Jan

2016-01-01

Roč. 6, č. 84 (2016), s. 81454-81460 ISSN 2046-2069 Institutional support: RVO:61388980 Keywords : solid-state reaction s * hydrogen storage properties * milled magnesium hydride Subject RIV: CA - Inorganic Chemistry Impact factor: 3.108, year: 2016

Fulminant leukemoid reaction due to postpartum Clostridium sordellii infection

Directory of Open Access Journals (Sweden)

Prabhat Agrawal

2012-01-01

Full Text Available Clostridium sordellii is gram positive anaerobic spore forming rod and it has been demonstrated to cause gas gangrene, refractory shock, leukemoid reaction, and pleuroperitoneal effusion due to capillary leak. We report here a case of postpartum female who presented with leukemoid reaction, ascites, pleural effusion, and shock without fever 7 days after normal vaginal home delivery.

Solvent Effects in Asymmetric Hetero Diels-Alder and Ene Reactions

DEFF Research Database (Denmark)

Johannsen, Mogens; Jørgensen, Karl Anker

1996-01-01

The use of polar solvents such as nitromethane or 2-nitropropane leads to a significant improvement of the catalytic properties of a cationic copper-Lewis acid in the hetero Diels-Alder reaction of alkyl glyoxylates with dienes; The scope of a newly developed copper(II)-bisoxazoline catalyst...... for the hetero Diels-Alder reaction is demonstrated by the reaction of different dienes with alkyl glyoxylates in nitroalkane solvents with the formation of the hetero Diels-Alder adduct in high enantiomeric excess as the major product. The synthetic application of the reaction is exemplified by an improved...

A method of coupling the Paternò-Büchi reaction with direct infusion ESI-MS/MS for locating the C[double bond, length as m-dash]C bond in glycerophospholipids.

Science.gov (United States)

Stinson, Craig A; Xia, Yu

2016-06-21

Tandem mass spectrometry (MS/MS) coupled with soft ionization is established as an essential platform for lipid analysis; however, determining high order structural information, such as the carbon-carbon double bond (C[double bond, length as m-dash]C) location, remains challenging. Recently, our group demonstrated a method for sensitive and confident lipid C[double bond, length as m-dash]C location determination by coupling online the Paternò-Büchi (PB) reaction with nanoelectrospray ionization (nanoESI) and MS/MS. Herein, we aimed to expand the scope of the PB reaction for lipid analysis by enabling the reaction with infusion ESI-MS/MS at much higher flow rates than demonstrated in the nanoESI setup (∼20 nL min(-1)). In the new design, the PB reaction was effected in a fused silica capillary solution transfer line, which also served as a microflow UV reactor, prior to ESI. This setup allowed PB reaction optimization and kinetics studies. Under optimized conditions, a maximum of 50% PB reaction yield could be achieved for a standard glycerophosphocholine (PC) within 6 s of UV exposure over a wide flow rate range (0.1-10 μL min(-1)). A solvent composition of 7 : 3 acetone : H2O (with 1% acid or base modifier) allowed the highest PB yields and good lipid ionization, while lower yields were obtained with an addition of a variety of organic solvents. Radical induced lipid peroxidation was identified to induce undesirable side reactions, which could be effectively suppressed by eliminating trace oxygen in the solution via N2 purge. Finally, the utility of coupling the PB reaction with infusion ESI-MS/MS was demonstrated by analyzing a yeast polar lipid extract where C[double bond, length as m-dash]C bond locations were revealed for 35 glycerophospholipids (GPs).

FINANCIAL MARKET REACTIONS TO INTERNATIONAL MERGERS & ACQUISITIONS IN THE BREWING INDUSTRY: AN EVENT STUDY ANALYSIS

OpenAIRE

Heyder, Matthias; Ebneth, Oliver; Theuvsen, Ludwig

2008-01-01

Cross-border acquisitions have been the growing trend in recent years in the world brewing industry, giving brewers the opportunity to enhance their degree of internationalization and market share remarkably. This study employs event study analysis to examine 31 mergers and acquisitions among leading European brewing groups. Differences regarding financial market reactions can be determined within the European peer group. Managerial implications as well as future research propositions conclud...

Interrogating the catalytic mechanism of nanoparticle mediated Stille coupling reactions employing bio-inspired Pd nanocatalysts

Science.gov (United States)

Pacardo, Dennis B.; Slocik, Joseph M.; Kirk, Kyle C.; Naik, Rajesh R.; Knecht, Marc R.

2011-05-01

To address issues concerning the global environmental and energy state, new catalytic technologies must be developed that translate ambient and efficient conditions to heavily used reactions. To achieve this, the structure/function relationship between model catalysts and individual reactions must be critically discerned to identify structural motifs responsible for the reactivity. This is especially true for nanoparticle-based systems where this level of information remains limited. Here we present evidence indicating that peptide-capped Pd nanoparticles drive Stille C-C coupling reactions via Pd atom leaching. Through a series of reaction studies, the materials are shown to be optimized for reactivity under ambient conditions where increases in temperature or catalyst concentration deactivate reactivity due to the leaching process. A quartz crystal microbalance analysis demonstrates that Pd leaching occurs during the initial oxidative addition step at the nanoparticle surface by aryl halides. Together, this suggests that peptide-based materials may be optimally suited for use as model systems to isolate structural motifs responsible for the generation of catalytically reactive materials under ambient synthetic conditions.

Interrogating the catalytic mechanism of nanoparticle mediated Stille coupling reactions employing bio-inspired Pd nanocatalysts.

Science.gov (United States)

Pacardo, Dennis B; Slocik, Joseph M; Kirk, Kyle C; Naik, Rajesh R; Knecht, Marc R

2011-05-01

To address issues concerning the global environmental and energy state, new catalytic technologies must be developed that translate ambient and efficient conditions to heavily used reactions. To achieve this, the structure/function relationship between model catalysts and individual reactions must be critically discerned to identify structural motifs responsible for the reactivity. This is especially true for nanoparticle-based systems where this level of information remains limited. Here we present evidence indicating that peptide-capped Pd nanoparticles drive Stille C-C coupling reactions via Pd atom leaching. Through a series of reaction studies, the materials are shown to be optimized for reactivity under ambient conditions where increases in temperature or catalyst concentration deactivate reactivity due to the leaching process. A quartz crystal microbalance analysis demonstrates that Pd leaching occurs during the initial oxidative addition step at the nanoparticle surface by aryl halides. Together, this suggests that peptide-based materials may be optimally suited for use as model systems to isolate structural motifs responsible for the generation of catalytically reactive materials under ambient synthetic conditions. © The Royal Society of Chemistry 2011

Reaction of the (111) faces of single-crystal indium phosphide with alkylating agents: evidence for selective reaction of the p-rich face

Energy Technology Data Exchange (ETDEWEB)

Spool, A.M.; Daube, K.A.; Mallouk, T.E.; Belmont, J.A.; Wrighton, M.S.

1986-05-28

We wish to report that the P-rich, (111)B, face of single-crystal InP, but not the In-rich, (111)A, face of the same crystal, reacts with molecular reagents to yield surface-bound material derived from the apparent alkylation of a surface P atom. Exploitation of surface functional groups has been demonstrated to be very important in the attachment of molecular reagents and polymers to electrode surfaces. Electrodes derivatized with molecules have potential uses in analysis, fuel cells, electrosynthetic cells, and photoelectrochemical cells. We now wish to present evidence showing that an important photoelectrode material, InP, can be functionalized with molecules by reaction of the P-rich, (111)B, face with alkylating reagents.

Synthesis by combustion reaction of ZnAl2O4 and application in methyl alcoholysis of soybean oil

International Nuclear Information System (INIS)

Dantas, B.B.; Silva, A.S.; Cunha, R.B.L.; Leal, E.; Costa, A.C.F.M.

2011-01-01

Biodiesel currently presents itself as a viable alternative to diesel oil front. However, implementation of actions most economic use as heterogeneous catalysts, allows further reduction of this biofuel by procedural steps. This work was supported application of catalytic ZnAl 2 O 4 obtained by combustion reaction in methyl alcoholysis of soybean oil. Samples of the supports were characterized by XRD, textural analysis by nitrogen adsorption and FTIR. The reaction tests were performed at 200°C, molar ratio 1:25, 2 and 4 wt% of catalyst and reaction time of 3 hours. XRD results indicate that the phase was obtained ZnAl 2 O 4 effectively, with surface areas of 14.9 and 8.6 m 2 g -1 . The tests demonstrated that reactional higher content of ester was 56.1 and 63.1% for the percentage of catalyst 2 and 4% respectively. (author)

FT-IR spectroscopic imaging of reactions in multiphase flow in microfluidic channels.

Science.gov (United States)

Chan, K L Andrew; Kazarian, Sergei G

2012-05-01

Rapid, in situ, and label-free chemical analysis in microfluidic devices is highly desirable. FT-IR spectroscopic imaging has previously been shown to be a powerful tool to visualize the distribution of different chemicals in flows in a microfluidic device at near video rate imaging speed without tracers or dyes. This paper demonstrates the possibility of using this imaging technology to capture the chemical information of all reactants and products at different points in time and space in a two-phase system. Differences in the rates of chemical reactions in laminar flow and segmented flow systems are also compared. Neutralization of benzoic acid in decanol with disodium phosphate in water has been used as the model reaction. Quantitative information, such as concentration profiles of reactant and products, can be extracted from the imaging data. The same feed flow rate was used in both the laminar flow and segmented flow systems. The laminar flow pattern was achieved using a plain wide T-junction, whereas the segmented flow was achieved by introducing a narrowed section and a nozzle at the T-junction. The results show that the reaction rate is limited by diffusion and is much slower with the laminar flow pattern, whereas the reaction is completed more quickly in the segmented flow due to better mixing.

Psychological reactions to catastrophes: fear as a reaction to accidents and emergencies in industriel complexes

International Nuclear Information System (INIS)

Wernli, G.

1989-01-01

This paper addresses the subject 'stress' and its effects on the personality. Specific types of behavior, which the human develops in a fearful situation are demonstrated by means of the psychoanalytical personality model. In the conclusion possible methods of alleviating fear, shock and panic reactions are described. 7 figs., 2 tabs., 9 refs

Vibratory Reaction Unit for the Rapid Analysis of Proteins and Glycochains

Directory of Open Access Journals (Sweden)

Yukie Sasakura

2007-01-01

Full Text Available A protein digestion system using immobilized enzymes for protein identification and glycochain analyses has been developed, and a vibration reaction unit for micro-scale sample convection on an enzyme-immobilized solid surface was constructed. BSA as a model substrate was digested by this unit, and was successfully identified by mass spectrometry (MS analyses. Compared to the conventional liquid-phase digestion, the reaction unit increased the number of matched peptides from 9 to 26, protein score from 455 to 1247, and sequence coverage from 21% to 48%. Glycopeptidase F (NGF, an enzyme that cleaves N-glycans from glycoproteins, was also immobilized and used to remove the glycochains from human immunoglobulin G (IgG. Trypsin and NGF were immobilized on the same solid surface and used to remove glycochains from IgG in single-step. Glycochains were labeled with fluorescent reagent and analyzed by HPLC. Several peaks corresponding to the glycochains of IgG were detected. These results suggested that the single-step digestion system, by immobilized multiple enzymes (trypsin and NGF would be effective for the rapid structural analysis of glycoproteins.Abbreviations: BSA: bovine serum albumin; MS: mass spectrometry; NGF: glycopeptidase F; IgG: immunoglobulin G; PTM: post-translational modification; HPLC: high-performance liquid chromatography; PBS: phosphate-buffered saline; EDTA: ethylenediaminetetraacetic acid; DTT: dithiothreitol; RT: retention time; ABOE: p-aminobenzoic acid octyl ester; PDMS: polydimethylsiloxane; ArgC: endoprotease Arginine C.

Multipole decomposition analysis of the 27Al, 90Zr, 208Pb(p, n) reactions at 295 MeV

International Nuclear Information System (INIS)

Wakasa, T.; Greenfield, M.B.; Koori, N.; Okihana, A.; Hatanaka, K.

1996-01-01

Differential cross sections at θ lab between 0 and 15 and the polarization transfer D NN at zero degrees for the 27 Al, 90 Zr, 208 Pb(p,n) reactions are measured at a bombarding energy of 295 MeV. A multipole decomposition (MD) technique is applied to extract L=0, L=1, and L≥2 contributions to the cross sections. The summed Gamow-Teller strength B(GT) is compared with shell-model calculations for the 27 Al(p,n) and 90 Zr(p,n) reactions. The usefulness of the polarization transfer observable in the MD analysis is discussed. (orig.)

Study on reaction mechanism by analysis of kinetic energy spectra of light particles and formation of final products

Science.gov (United States)

Giardina, G.; Mandaglio, G.; Nasirov, A. K.; Anastasi, A.; Curciarello, F.; Fazio, G.

2018-05-01

The sensitivity of reaction mechanism in the formation of compound nucleus (CN) by the analysis of kinetic energy spectra of light particles and of reaction products are shown. The dependence of the P CN fusion probability of reactants and W sur survival probability of CN against fission at its deexcitation on the mass and charge symmetries in the entrance channel of heavy-ion collisions, as well as on the neutron numbers is discussed. The possibility of conducting a complex program of investigations of the complete fusion by reliable ways depends on the detailed and refined methods of experimental and theoretical analyses.

Kinetic modeling of reactions in Foods

NARCIS (Netherlands)

Boekel, van M.A.J.S.

2008-01-01

The level of quality that food maintains as it travels down the production-to-consumption path is largely determined by the chemical, biochemical, physical, and microbiological changes that take place during its processing and storage. Kinetic Modeling of Reactions in Foods demonstrates how to

Unimolecular and collisionally induced ion reactions

International Nuclear Information System (INIS)

Beynon, J.H.; Boyd, R.K.

1978-01-01

The subject is reviewed under the following headings: introduction (mass spectroscopy and the study of fragmentation reactions of gaseous positive ions); techniques and methods (ion sources, detection systems, analysis of ions, data reduction); collision-induced reactions of ions and unimolecular fragmentations of metastable ions; applications (ion structure, energetic measurements, analytical applications, other applications). 305 references. (U.K.)

Exploring Reaction Mechanism on Generalized Force Modified Potential Energy Surfaces (G-FMPES) for Diels-Alder Reaction

Science.gov (United States)

Jha, Sanjiv; Brown, Katie; Subramanian, Gopinath

We apply a recent formulation for searching minimum energy reaction path (MERP) and saddle point to atomic systems subjected to an external force. We demonstrate the effect of a loading modality resembling hydrostatic pressure on the trans to cis conformational change of 1,3-butadiene, and the simplest Diels-Alder reaction between ethylene and 1,3-butadiene. The calculated MERP and saddle points on the generalized force modified potential energy surface (G-FMPES) are compared with the corresponding quantities on an unmodified potential energy surface. Our study is performed using electronic structure calculations at the HF/6-31G** level as implemented in the AIMS-MOLPRO code. Our calculations suggest that the added compressive pressure lowers the energy of cis butadiene. The activation energy barrier for the concerted Diels-Alder reaction is found to decrease progressively with increasing compressive pressure.

Glider-based computing in reaction-diffusion hexagonal cellular automata

International Nuclear Information System (INIS)

Adamatzky, Andrew; Wuensche, Andrew; De Lacy Costello, Benjamin

2006-01-01

A three-state hexagonal cellular automaton, discovered in [Wuensche A. Glider dynamics in 3-value hexagonal cellular automata: the beehive rule. Int J Unconvention Comput, in press], presents a conceptual discrete model of a reaction-diffusion system with inhibitor and activator reagents. The automaton model of reaction-diffusion exhibits mobile localized patterns (gliders) in its space-time dynamics. We show how to implement the basic computational operations with these mobile localizations, and thus demonstrate collision-based logical universality of the hexagonal reaction-diffusion cellular automaton

Simultaneous Nuclear Reaction Analysis of Boron and Phosphorus in Thin Borophosphosilicate Glass Films Using (α,p) Reactions

International Nuclear Information System (INIS)

Walsh, D.S.; Doyle, B.L.

1999-01-01

A method combining (α,p) NRA and ellipsometry has been developed for measuring the Boron and Phosphorus content of borophosphosilicate glass (BPSG) used for interlevel dielectrics in integrated circuits. Yields from the 31 P(α,p 0 ) 34 S (Q = 0.63 MeV) and 10 B(α,p 0 ) 13 C (Q = 4.06 MeV) reactions are coupled with ellipsometry thickness measurements to calculate the average atomic percent of B and P in the film. Due to the relatively low Q value of the 31 P(α,p 0 ) 34 S reaction and the thickness range of the glass films (le 1.2 micrometers) they analyze, fairly high energy alpha particles, and Mylar range foils on the detector are required. Alpha energy, detector angle and range foil thickness were determined by reaction yields and the need to separate the yield peaks of interest from competing (α,p) reactions and backscattered alphas. They have determined that 6.0 MeV incident alphas with a detector angle of 135degree and about 100 micrometers of Mylar range foil are optimum for the system. The yield for the 10 B(α,p 0 ) 13 C reaction is quite constant in the energy range of interest (approximately 5.8 to 6 MeV) but the yield for the 31 P(α,p 0 ) 34 S is not. Consequently, a simple conversion from standard BPSG reference samples (independently quantified by ICP mass spectrometry) is adequate to calculate a film's %B content. The %P calculation is more complex, involving a three-dimensional fit of the P yield data and measured film thickness to the film %P content. This fit is based upon yield data from a matrix of standard film samples. The technique is sensitive to 0.1% with an accuracy of ±3 to ±10% depending on the sample. This measurement method is used routinely at Sandia National Laboratories in support of their fabrication process lines

Reaction list for charged-particle-induced nuclear reactions: Z = 1 to Z = 98 (H to Cf), July 1973--September 1974

International Nuclear Information System (INIS)

McGowan, F.K.; Milner, W.T.

1975-01-01

This Reaction List for charged-particle-induced nuclear reactions has been prepared from the journal literature for the period from July 1973 through September 1974. Each published experimental paper is listed under the target nucleus in the nuclear reaction with a brief statement of the type of data in the paper. The nuclear reaction is denoted by A(a,b)B, where the mass of a is greater than or equal to (one nucleon mass). There is no restriction on energy. Nuclear reactions involving mesons in the outgoing channel are not included. Theoretical papers which treat directly with the analysis of nuclear reaction data and results are included in the Reaction List. The cutoff date for literature was September 30, 1974. (U.S.)

Acoustic Resonance Reaction Control Thruster (ARCTIC), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — ORBITEC proposes to develop and demonstrate the innovative Acoustic Resonance Reaction Control Thruster (ARCTIC) to provide rapid and reliable in-space impulse...

Combined steam and carbon dioxide reforming of methane and side reactions: Thermodynamic equilibrium analysis and experimental application

International Nuclear Information System (INIS)

Jang, Won-Jun; Jeong, Dae-Woon; Shim, Jae-Oh; Kim, Hak-Min; Roh, Hyun-Seog; Son, In Hyuk; Lee, Seung Jae

2016-01-01

Highlights: • Selected variables have a significant influence on yields of synthesis gas. • (CO_2 + H_2O)/CH_4 affects the temperature which can achieve the maximum conversion. • Coke is formed at low temperatures even with excess oxidizing agent. • The occurrence of RWGS becomes critical in real chemical reactions. • Equilibrium conversions are maintained for 500 h without detectable deactivation. - Abstract: Thermodynamic equilibrium analysis of the combined steam and carbon dioxide reforming of methane (CSCRM) and side reactions was performed using total Gibbs free energy minimization. The effects of (CO_2 + H_2O)/CH_4 ratio (0.9–2.9), CO_2:H_2O ratio (3:1–1:3), and temperature (500–1000 °C) on the equilibrium conversions, yields, coke yield, and H_2/CO ratio were investigated. A (CO_2 + H_2O)/CH_4 ratio greater than 1.2, a CO_2:H_2O ratio of 1:2.1, and a temperature of at least 850 °C are preferable reaction conditions for the synthesis gas preparation in the gas to liquid process. Simulated conditions were applied to the CSCRM reaction and the experimental data were compared with the thermodynamic equilibrium results. The thermodynamic equilibrium results were mostly consistent with the experimental data, but the reverse water gas shift reaction rapidly occurred in the real chemical reaction and under excess oxidizing agent conditions. In addition, a long-term stability test (under simulated conditions) showed that the equilibrium conversion was maintained for 500 h and that the coke formation on the used catalyst was not observed.

Compilation and R-matrix analysis of Big Bang nuclear reaction rates

International Nuclear Information System (INIS)

Descouvemont, Pierre; Adahchour, Abderrahim; Angulo, Carmen; Coc, Alain; Vangioni-Flam, Elisabeth

2004-01-01

We use the R-matrix theory to fit low-energy data on nuclear reactions involved in Big Bang nucleosynthesis. Special attention is paid to the rate uncertainties which are evaluated on statistical grounds. We provide S factors and reaction rates in tabular and graphical formats

Kinematic relations in heavy-ion reactions

International Nuclear Information System (INIS)

Gippner, P.; Kalpakchieva, R.

1988-01-01

The present work gives a short overview of the non-relativistic kinematics of nuclear reactions derived on the basis of the conservation laws of energy and linear momentum. Section 2 contains kinematic relations valid for two-body reactions, sections 3 makes use of these relations to describe sequential fission as a special case of reactions with three particles in the exit channel. It is the aim of this work to comprise the kinematic formulae essential for planning of experiments, data analysis and critical examination of the obtained results. (author)

Continuum spectra in light-ion reactions

Energy Technology Data Exchange (ETDEWEB)

Tamura, T.; Udagawa, T. [Texas Univ., Austin (USA). Dept. of Physics; Ikegami, H.; Muraoka, M [eds.

1980-01-01

Recent developments in the use of multi-step direct reaction method, to fit continuum cross sections of light-ion reactions, are reviewed. There has been a long-standing difficulty in reproducing sufficiently large (p, p') continuum cross section, but it has now been all but removed. It will be discussed in some detail, how this was achieved. Analyses of very recent data on analyzing powers in the continuum of (p, p') and (p, ..cap alpha..) reactions will also be discussed. Finally, analysis of the breakup of h into d and p will be presented.

Nanoscale studies of cement chemistry with {sup 15}N resonance reaction analysis

Energy Technology Data Exchange (ETDEWEB)

Schweitzer, Jeffrey S. [University of Connecticut, Department of Physics, Unit 3046, Storrs, CT 06269-3046 (United States)]. E-mail: schweitz@phys.uconn.edu; Livingston, Richard A. [Federal Highway Administration, HRDI-05, 6300 Georgetown Pike McLean, VA 22101 (United States); Rolfs, Claus [Institut fuer Physik mit Ionenstrahlen, Ruhr-Universitaet, Bochum Universitaetsstr. 150, Gebaeude NB 3, 44780 Bochum (Germany); Becker, Hans-Werner [Institut fuer Physik mit Ionenstrahlen, Ruhr-Universitaet, Bochum Universitaetsstr. 150, Gebaeude NB 3, 44780 Bochum (Germany); Kubsky, Stefan [Institut fuer Physik mit Ionenstrahlen, Ruhr-Universitaet, Bochum Universitaetsstr. 150, Gebaeude NB 3, 44780 Bochum (Germany); Spillane, Timothy [University of Connecticut, Department of Physics, Unit 3046, Storrs, CT 06269-3046 (United States); Castellote, Marta [Institute of Construction Science ' Eduardo Torroja' (CSIC), Serrano Galvache no. 4, 28033 Madrid (Spain); Viedma, Paloma G. de [Institute of Construction Science ' Eduardo Torroja' (CSIC), Serrano Galvache no. 4, 28033 Madrid (Spain)

2005-12-15

Analyses of materials with ion beams have proven to be a valuable technique for describing the spatial distributions of specific elements in host materials. We have applied this technique using the {sup 15}N(p, {alpha}{gamma}){sup 12}C reaction to study the time dependence of the chemical reactions involved in the curing of cement. By using the Dynamitron Tandem accelerator at the Ruhr Universitaet, Bochum, Germany, we have been able to achieve a few nanometer spatial resolution at the surface of cement grains and to study the hydrogen distributions to a depth of about 2 {mu}m. By applying a technique for stopping the chemical reactions at arbitrary times, the time dependence of the chemical reactions involving specific components of cement can be investigated. In addition, the effects of additives on the chemical reactions have been studied, as have materials that are components of concrete.

α -induced reactions on 115In: Cross section measurements and statistical model analysis

Science.gov (United States)

Kiss, G. G.; Szücs, T.; Mohr, P.; Török, Zs.; Huszánk, R.; Gyürky, Gy.; Fülöp, Zs.

2018-05-01

Background: α -nucleus optical potentials are basic ingredients of statistical model calculations used in nucleosynthesis simulations. While the nucleon+nucleus optical potential is fairly well known, for the α +nucleus optical potential several different parameter sets exist and large deviations, reaching sometimes even an order of magnitude, are found between the cross section predictions calculated using different parameter sets. Purpose: A measurement of the radiative α -capture and the α -induced reaction cross sections on the nucleus 115In at low energies allows a stringent test of statistical model predictions. Since experimental data are scarce in this mass region, this measurement can be an important input to test the global applicability of α +nucleus optical model potentials and further ingredients of the statistical model. Methods: The reaction cross sections were measured by means of the activation method. The produced activities were determined by off-line detection of the γ rays and characteristic x rays emitted during the electron capture decay of the produced Sb isotopes. The 115In(α ,γ )119Sb and 115In(α ,n )Sb118m reaction cross sections were measured between Ec .m .=8.83 and 15.58 MeV, and the 115In(α ,n )Sb118g reaction was studied between Ec .m .=11.10 and 15.58 MeV. The theoretical analysis was performed within the statistical model. Results: The simultaneous measurement of the (α ,γ ) and (α ,n ) cross sections allowed us to determine a best-fit combination of all parameters for the statistical model. The α +nucleus optical potential is identified as the most important input for the statistical model. The best fit is obtained for the new Atomki-V1 potential, and good reproduction of the experimental data is also achieved for the first version of the Demetriou potentials and the simple McFadden-Satchler potential. The nucleon optical potential, the γ -ray strength function, and the level density parametrization are also

Kinetics Analysis of Synthesis Reaction of Struvite With Air-Flow Continous Vertical Reactors

Science.gov (United States)

Edahwati, L.; Sutiyono, S.; Muryanto, S.; Jamari, J.; Bayuseno, dan A. P.

2018-01-01

Kinetics reaction is a knowledge about a rate of chemical reaction. The differential of the reaction rate can be determined from the reactant material or the formed material. The reaction mechanism of a reactor may include a stage of reaction occurring sequentially during the process of converting the reactants into products. In the determination of reaction kinetics, the order of reaction and the rate constant reaction must be recognized. This study was carried out using air as a stirrer as a medium in the vertical reactor for crystallization of struvite. Stirring is one of the important aspects in struvite crystallization process. Struvite crystals or magnesium ammonium phosphate hexahydrates (MgNH4PO4·6H2O) is commonly formed in reversible reactions and can be generated as an orthorhombic crystal. Air is selected as a stirrer on the existing flow pattern in the reactor determining the reaction kinetics of the crystal from the solution. The experimental study was conducted by mixing an equimolar solution of 0.03 M NH4OH, MgCl2 and H3PO4 with a ratio of 1: 1: 1. The crystallization process of the mixed solution was observed in an inside reactor at the flow rate ranges of 16-38 ml/min and the temperature of 30°C was selected in the study. The air inlet rate was kept constant at 0.25 liters/min. The pH solution was adjusted to be 8, 9 and 10 by dropping wisely of 1 N KOH solution. The crystallization kinetics was examined until the steady state of the reaction was reached. The precipitates were filtered and dried at a temperature for subsequent material characterization, including Scanning Electron Microscope (SEM) and XRD (X-Ray diffraction) method. The results show that higher flow rate leads to less mass of struvite.

Numerical solution of the unsteady diffusion-convection-reaction equation based on improved spectral Galerkin method

Science.gov (United States)

Zhong, Jiaqi; Zeng, Cheng; Yuan, Yupeng; Zhang, Yuzhe; Zhang, Ye

2018-04-01

The aim of this paper is to present an explicit numerical algorithm based on improved spectral Galerkin method for solving the unsteady diffusion-convection-reaction equation. The principal characteristics of this approach give the explicit eigenvalues and eigenvectors based on the time-space separation method and boundary condition analysis. With the help of Fourier series and Galerkin truncation, we can obtain the finite-dimensional ordinary differential equations which facilitate the system analysis and controller design. By comparing with the finite element method, the numerical solutions are demonstrated via two examples. It is shown that the proposed method is effective.

Real-time polymerase chain reaction for diagnosing infectious mononucleosis in pediatric patients: A systematic review and meta-analysis.

Science.gov (United States)

Jiang, Sha-Yi; Yang, Jing-Wei; Shao, Jing-Bo; Liao, Xue-Lian; Lu, Zheng-Hua; Jiang, Hui

2016-05-01

In this meta-analysis, we evaluated the diagnostic role of Epstein-Barr virus deoxyribonucleic acid detection and quantitation in the serum of pediatric and young adult patients with infectious mononucleosis. The primary outcome of this meta-analysis was the sensitivity and specificity of Epstein-Barr virus (EBV) deoxyribonucleic acid (DNA) detection and quantitation using polymerase chain reaction (PCR). A systematic review and meta-analysis was performed by searching for articles that were published through September 24, 2014 in the following databases: Medline, Cochrane, EMBASE, and Google Scholar. The following keywords were used for the search: "Epstein-Barr virus," "infectious mononucleosis," "children/young adults/infant/pediatric," and "polymerase chain reaction or PCR." Three were included in this analysis. We found that for detection by PCR, the pooled sensitivity for detecting EBV DNA was 77% (95%CI, 66-86%) and the pooled specificity for was 98% (95%CI, 93-100%). Our findings indicate that this PCR-based assay has high specificity and good sensitivity for detecting of EBV DNA, indicating it may useful for identifying patients with infectious mononucleosis. This assay may also be helpful to identify young athletic patients or highly physically active pediatric patients who are at risk for a splenic rupture due to acute infectious mononucleosis. © 2015 Wiley Periodicals, Inc.

Escherichia coli Phosphoenolpyruvate-Dependent Phosphotransferase System. Functional Asymmetry in Enzyme I Subunits Demonstrated by Reaction with 3-Bromopyruvate

NARCIS (Netherlands)

Hoeve-Duurkens, Ria ten; Robillard, George T.

1984-01-01

In the bacterial phosphoenolpyruvate-dependent sugar transport systems, enzyme I (EI) is responsible for the initial reaction step which is the transfer of the phosphoryl group from phosphoenolpyruvate to a cytoplasmic phosphocarrier protein (HPr). The inactivation of enzyme I by the substrate

Electric vehicle demonstration

Energy Technology Data Exchange (ETDEWEB)

Ouellet, M. [National Centre for Advanced Transportation, Saint-Jerome, PQ (Canada)

2010-07-01

The desirable characteristics of Canadian projects that demonstrate vehicle use in real-world operation and the appropriate mechanism to collect and disseminate the monitoring data were discussed in this presentation. The scope of the project was on passenger cars and light duty trucks operating in plug-in electric vehicle (PHEV) or battery electric vehicle modes. The presentation also discussed the funding, stakeholders involved, Canadian travel pattern analysis, regulatory framework, current and recent electric vehicle demonstration projects, and project guidelines. It was concluded that some demonstration project activities may have been duplicated as communication between the proponents was insufficient. It was recommended that data monitoring using automatic data logging with minimum reliance on logbooks and other user entry should be emphasized. figs.

Modeling chemical reactions for drug design.

Science.gov (United States)

Gasteiger, Johann

2007-01-01

Chemical reactions are involved at many stages of the drug design process. This starts with the analysis of biochemical pathways that are controlled by enzymes that might be downregulated in certain diseases. In the lead discovery and lead optimization process compounds have to be synthesized in order to test them for their biological activity. And finally, the metabolism of a drug has to be established. A better understanding of chemical reactions could strongly help in making the drug design process more efficient. We have developed methods for quantifying the concepts an organic chemist is using in rationalizing reaction mechanisms. These methods allow a comprehensive modeling of chemical reactivity and thus are applicable to a wide variety of chemical reactions, from gas phase reactions to biochemical pathways. They are empirical in nature and therefore allow the rapid processing of large sets of structures and reactions. We will show here how methods have been developed for the prediction of acidity values and of the regioselectivity in organic reactions, for designing the synthesis of organic molecules and of combinatorial libraries, and for furthering our understanding of enzyme-catalyzed reactions and of the metabolism of drugs.

Lagrangian descriptors of driven chemical reaction manifolds.

Science.gov (United States)

Craven, Galen T; Junginger, Andrej; Hernandez, Rigoberto

2017-08-01

The persistence of a transition state structure in systems driven by time-dependent environments allows the application of modern reaction rate theories to solution-phase and nonequilibrium chemical reactions. However, identifying this structure is problematic in driven systems and has been limited by theories built on series expansion about a saddle point. Recently, it has been shown that to obtain formally exact rates for reactions in thermal environments, a transition state trajectory must be constructed. Here, using optimized Lagrangian descriptors [G. T. Craven and R. Hernandez, Phys. Rev. Lett. 115, 148301 (2015)PRLTAO0031-900710.1103/PhysRevLett.115.148301], we obtain this so-called distinguished trajectory and the associated moving reaction manifolds on model energy surfaces subject to various driving and dissipative conditions. In particular, we demonstrate that this is exact for harmonic barriers in one dimension and this verification gives impetus to the application of Lagrangian descriptor-based methods in diverse classes of chemical reactions. The development of these objects is paramount in the theory of reaction dynamics as the transition state structure and its underlying network of manifolds directly dictate reactivity and selectivity.

C-terminal peptide extension via gas-phase ion/ion reactions

Science.gov (United States)

Peng, Zhou; McLuckey, Scott A.

2015-01-01

The formation of peptide bonds is of great importance from both a biological standpoint and in routine organic synthesis. Recent work from our group demonstrated the synthesis of peptides in the gas-phase via ion/ion reactions with sulfo-NHS reagents, which resulted in conjugation of individual amino acids or small peptides to the N-terminus of an existing ‘anchor’ peptide. Here, we demonstrate a complementary approach resulting in the C-terminal extension of peptides. Individual amino acids or short peptides can be prepared as reagents by incorporating gas phase-labile protecting groups to the reactive C-terminus and then converting the N-terminal amino groups to the active ketenimine reagent. Gas-phase ion/ion reactions between the anionic reagents and doubly protonated “anchor” peptide cations results in extension of the “anchor” peptide with new amide bond formation at the C-terminus. We have demonstrated that ion/ion reactions can be used as a fast, controlled, and efficient means for C-terminal peptide extension in the gas phase. PMID:26640400

Reaction Heterogeneity in LiNi _0.8 Co _0.15 Al _0.05 O ₂ Induced by Surface Layer

Energy Technology Data Exchange (ETDEWEB)

Grenier, Antonin [X-ray; Liu, Hao [X-ray; Wiaderek, Kamila M. [X-ray; Lebens-Higgins, Zachary W. [Department; Borkiewicz, Olaf J. [X-ray; Piper, Louis F. J. [Department; Chupas, Peter J. [Energy; Chapman, Karena W. [X-ray

2017-08-15

Through operando synchrotron powder X-ray diffraction (XRD) analysis of layered transition metal oxide electrodes of composition LiNi0.8Co0.15Al0.05O2 (NCA), we decouple the intrinsic bulk reaction mechanism from surface-induced effects. For identically prepared and cycled electrodes stored in different environments, we demonstrate that the intrinsic bulk reaction for pristine NCA follows solid-solution mechanism, not a two-phase as suggested previously. By combining high resolution powder X-ray diffraction, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and surface sensitive X-ray photoelectron spectroscopy (XPS), we demonstrate that adventitious Li2CO3 forms on the electrode particle surface during exposure to air, through reaction with atmospheric CO2. This surface impedes ionic and electronic transport to the underlying electrode, with progressive erosion of this layer during cycling giving rise to different reaction states in particles with an intact vs an eroded Li2CO3 surface-coating. This reaction heterogeneity, with a bimodal distribution of reaction states, has previously been interpreted as a “two-phase” reaction mechanism for NCA, as an activation step that only occurs during the first cycle. Similar surface layers may impact the reaction mechanism observed in other electrode materials using bulk probes such as operando powder XRD.

Malignant transformation of a potentially low risk lichenoid reaction

International Nuclear Information System (INIS)

Ashir, K.R.; Chatra, L.

2012-01-01

Lichenoid reaction represents a family of oral lesions identical, both clinically and histologically to oral lichen planus. The triggering factor for this lesion varies from medicines to dental materials, usually demonstrating a cause-effect relationship unlike lichen planus. We present a typical case of lichenoid reaction on the buccal mucosa that appeared in response to betel quid which progressed to carcinoma during a follow-up period of 6 months. Lichenoid reactions occurring in response to known carcinogens and that occurring in risk group population has to be observed more cautiously. (author)

Typewriting rate as a function of reaction time.

Science.gov (United States)

Hayes, V; Wilson, G D; Schafer, R L

1977-12-01

This study was designed to determine the relationship between reaction time and typewriting rate. Subjects were 24 typists ranging in age from 19 to 39 yr. Reaction times (.001 sec) to a light were recorded for each finger and to each alphabetic character and three punctuation marks. Analysis of variance yielded significant differences in reaction time among subjects and fingers. Correlation between typewriting rate and average reaction time to the alphabetic characters and three punctuation marks was --.75. Correlation between typewriting rate and the difference between the reaction time of the hands was --.42. Factors influencing typewriting rate may include reaction time of the fingers, difference between the reaction time of the hands, and reaction time to individual keys on the typewriter. Implications exist for instructional methodology and further research.

The reactions of neutral iron clusters with D2O: Deconvolution of equilibrium constants from multiphoton processes

International Nuclear Information System (INIS)

Weiller, B.H.; Bechthold, P.S.; Parks, E.K.; Pobo, L.G.; Riley, S.J.

1989-01-01

The chemical reactions of neutral iron clusters with D 2 O are studied in a continuous flow tube reactor by molecular beam sampling and time-of-flight mass spectrometry with laser photoionization. Product distributions are invariant to a four-fold change in reaction time demonstrating that equilibrium is attained between free and adsorbed D 2 O. The observed negative temperature dependence is consistent with an exothermic, molecular addition reaction at equilibrium. Under our experimental conditions, there is significant photodesorption of D 2 O (Fe/sub n/(D 2 O)/sub m/ + hν → Fe/sub n/ + m D 2 O) along with ionization due to absorption of multiple photons from the ionizing laser. Using a simple model based on a rate equation analysis, we are able to quantitatively deconvolute this desorption process from the equilibrium constants. 8 refs., 1 fig

Bayesian analysis of heat pipe life test data for reliability demonstration testing

International Nuclear Information System (INIS)

Bartholomew, R.J.; Martz, H.F.

1985-01-01

The demonstration testing duration requirements to establish a quantitative measure of assurance of expected lifetime for heat pipes was determined. The heat pipes are candidate devices for transporting heat generated in a nuclear reactor core to thermoelectric converters for use as a space-based electric power plant. A Bayesian analysis technique is employed, utilizing a limited Delphi survey, and a geometric mean accelerated test criterion involving heat pipe power (P) and temperature (T). Resulting calculations indicate considerable test savings can be achieved by employing the method, but development testing to determine heat pipe failure mechanisms should not be circumvented

Quantum radiation reaction in head-on laser-electron beam interaction

International Nuclear Information System (INIS)

Vranic, Marija; Grismayer, Thomas; Fonseca, Ricardo A; Silva, Luis O

2016-01-01

In this paper, we investigate the evolution of the energy spread and the divergence of electron beams while they interact with different laser pulses at intensities where quantum effects and radiation reaction are of relevance. The interaction is modelled with a quantum electrodynamic (QED)-PIC code and the results are compared with those obtained using a standard PIC code with a classical radiation reaction module. In addition, an analytical model is presented that estimates the value of the final electron energy spread after the interaction with the laser has finished. While classical radiation reaction is a continuous process, in QED, radiation emission is stochastic. The two pictures reconcile in the limit when the emitted photons energy is small compared to the energy of the emitting electrons. The energy spread of the electron distribution function always tends to decrease with classical radiation reaction, whereas the stochastic QED emission can also enlarge it. These two tendencies compete in the QED-dominated regime. Our analysis, supported by the QED module, reveals an upper limit to the maximal attainable energy spread due to stochasticity that depends on laser intensity and the electron beam average energy. Beyond this limit, the energy spread decreases. These findings are verified for different laser pulse lengths ranging from short ∼30 fs pulses presently available to the long ∼150 fs pulses expected in the near-future laser facilities, and compared with a theoretical model. Our results also show that near future experiments will be able to probe this transition and to demonstrate the competition between enhanced QED induced energy spread and energy spectrum narrowing from classical radiation reaction. (paper)

Perceived Insider Status and Feedback Reactions: A Dual Path of Feedback Motivation Attribution

Directory of Open Access Journals (Sweden)

Weijiong Wu

2017-05-01

Full Text Available Many studies have evaluated how the characteristics of feedback receiver, feedback deliverer and feedback information influence psychological feedback reactions of the feedback receiver while largely neglecting that feedback intervention is a kind of social interaction process. To address this issue, this study proposes that employees’ perceived insider status (PIS, as a kind of employee-organization relationship, could also influence employees’ reactions to supervisory feedback. In particular, this study investigates the influence of PIS focusing on affective and cognitive feedback reactions, namely feedback satisfaction and feedback utility. Surveys were conducted in a machinery manufacturing company in the Guangdong province of China. Samples were collected from 192 employees. Data analysis demonstrated that PIS and feedback utility possessed a U-shaped relationship, whereas PIS and feedback satisfaction exhibited positively linear relationships. The analysis identified two kinds of mediating mechanisms related to feedback satisfaction and feedback utility. Internal feedback motivation attribution partially mediated the relationship between PIS and feedback satisfaction but failed to do the same with respect to the relationship between PIS and feedback utility. In contrast, external feedback motivation attribution partially mediated the relationship between PIS and feedback utility while failing to mediate the relationship between PIS and feedback satisfaction. Theoretical contributions and practical implications of the findings are discussed at the end of the paper.

Experimental Demonstration and Theoretical Analysis of Slow Light in a Semiconductor Waveguide at GHz Frequencies

DEFF Research Database (Denmark)

Mørk, Jesper; Kjær, Rasmus; Poel, Mike van der

2005-01-01

Experimental demonstration and theoretical analysis of slow light in a semiconductor waveguide at GHz frequencies slow-down of light by a factor of two in a semiconductor waveguide at room temperature with a bandwidth of 16.7 GHz using the effect of coherent pulsations of the carrier density...

Kinetic analysis of the reactions of hypobromous acid with protein components

DEFF Research Database (Denmark)

Pattison, David I; Davies, Michael Jonathan

2004-01-01

available for HOBr. In this study, rate constants for reaction of HOBr with protein components have been determined. The second-order rate constants (22 degrees C, pH 7.4) for reaction with protein sites vary by 8 orders of magnitude and decrease in the order Cys > Trp approximately Met approximately His...

Ene-ene-yne Reactions: Activation Strain Analysis and Role of Aromaticity

NARCIS (Netherlands)

Fernandez, I.; Bickelhaupt, F.M.; Cossío, F.P.

2014-01-01

The trend in reactivity of the thermal cycloisomerization reactions of 1,3-hexadien-5-ynes, A=B-C=D-E≡F, were explored and analyzed by using density functional theory at the M06-2X/def2-TZVPP level. These reactions proceed through formally aromatic transition states to form a bent-allene

Product differentiation by analysis of DNA melting curves during the polymerase chain reaction.

Science.gov (United States)

Ririe, K M; Rasmussen, R P; Wittwer, C T

1997-02-15

A microvolume fluorometer integrated with a thermal cycler was used to acquire DNA melting curves during polymerase chain reaction by fluorescence monitoring of the double-stranded DNA specific dye SYBR Green I. Plotting fluorescence as a function of temperature as the thermal cycler heats through the dissociation temperature of the product gives a DNA melting curve. The shape and position of this DNA melting curve are functions of the GC/AT ratio, length, and sequence and can be used to differentiate amplification products separated by less than 2 degrees C in melting temperature. Desired products can be distinguished from undesirable products, in many cases eliminating the need for gel electrophoresis. Analysis of melting curves can extend the dynamic range of initial template quantification when amplification is monitored with double-stranded DNA specific dyes. Complete amplification and analysis of products can be performed in less than 15 min.

A Simple Method To Demonstrate the Enzymatic Production of Hydrogen from Sugar

Science.gov (United States)

Hershlag, Natalie; Hurley, Ian; Woodward, Jonathan

1998-10-01

There is current interest in and concern for the development of environmentally friendly bioprocesses whereby biomass and the biodegradable content of municipal wastes can be converted to useful forms of energy. For example, cellulose, a glucose polymer that is the principal component of biomass and paper waste, can be enzymatically degraded to glucose, which can subsequently be converted by fermentation or further enzymatic reaction to fuels such as ethanol or hydrogen. These products represent alternative energy sources to fossil fuels such as oil. Demonstration of the relevant reactions in high-school and undergraduate college laboratories would have value not only in illustrating environmentally friendly biotechnology for the utilization of renewable energy sources, such as cellulosic wastes, but could also be used to teach the principles of enzyme-catalyzed reactions. In the experimental protocol described here, it has been demonstrated that the common sugar glucose can be used to produce hydrogen using two enzymes, glucose dehydrogenase and hydrogenase. No sophisticated or expensive hydrogen detection equipment is required-only a redox dye, benzyl viologen, which turns purple when it is reduced. The color can be detected by a simple colorimeter. Furthermore, it is shown that the renewable resource cellulose, in its soluble derivative from carboxymethylcellulose, as well as aspen-wood waste, is also a source of hydrogen if the enzyme cellulase is included in the reaction mixture.

The effect of mass transport on the graphite/CO2 reaction

International Nuclear Information System (INIS)

Stephen, W.J.

1984-11-01

The Graphite/CO 2 reaction is strongly inhibited by the reaction product CO and therefore any model for the influence of mass transport on reaction rate should consider this. The problem of internal mass transport alone has been considered in previous notes. This note extends the models to include external mass transport. Results are compared with simple first order reaction with no volume change. The calculations demonstrate that, for strong CO inhibition, external mass transport limits reaction at a much lower rate than for first order kinetics and that the usual concept of three reaction zones corresponding to chemical control, in-pore diffusion control and boundary layer control can be unrealistically idealised. (U.K.)

Proton conduction based on intracrystalline chemical reaction

International Nuclear Information System (INIS)

Schuck, G.; Lechner, R.E.; Langer, K.

2002-01-01

Proton conductivity in M 3 H(SeO 4 ) 2 crystals (M=K, Rb, Cs) is shown to be due to a dynamic disorder in the form of an intracrystalline chemical equilibrium reaction: alternation between the association of the monomers [HSeO 4 ] 1- and [SeO 4 ] 2- resulting in the dimer [H(SeO 4 ) 2 ] 3- (H-bond formation) and the dissociation of the latter into the two monomers (H-bond breaking). By a combination of quasielastic neutron scattering and FTIR spectroscopy, reaction rates were obtained, as well as rates of proton exchange between selenate ions, leading to diffusion. The results demonstrate that this reaction plays a central role in the mechanism of proton transport in these solid-state protonic conductors. (orig.)

Global Handwashing Day 2012: a qualitative content analysis of Chinese social media reaction to a health promotion event.

Science.gov (United States)

Fung, Isaac Chun-Hai; Cai, Jingxian; Hao, Yi; Ying, Yuchen; Chan, Benedict Shing Bun; Tse, Zion Tsz Ho; Fu, King-Wa

2015-01-01

Global Handwashing Day (GHD) is a handwashing promotion campaign organized by the Global Public-Private Partnership of Handwashing with Soap. In China, it has been promoted by the Chinese public health authorities, international organizations and multinational corporations through various channels including social media such as Sina Weibo, the leading Chinese microblogging site similar to Twitter. The objective of this study is to qualitatively assess Chinese social media users' reactions to a health promotion campaign using Global Handwashing Day (GHD) 2012 as an example. We conducted a qualitative content analysis of 552 Weibo posts generated on GHD 2012 by Weibo users with 1000 or more followers with the Chinese keyword for "handwashing." We categorized the Weibo posts into groups by keywords that frequently appeared in the data set. These groups were either exact reposts of an original post, or they conveyed similar information. We observed the interconnections between traditional media and social media in handwashing promotion. Social media were found to serve as amplifiers of contents provided by traditional media. We observed the contextualization of global hygiene messages in a unique national social media market in China. Our study showed that social media and traditional media are two interconnected arms of the GHD campaign in China. Our analysis demonstrated that public health campaigns in China can be evaluated using social media data. The themes and topics identified in this study will help public health practitioners evaluate future social media handwashing promotion campaigns.

The first organocatalytic, ortho-regioselective inverse-electron-demand hetero-Diels-Alder reaction.

Science.gov (United States)

Hejmanowska, Joanna; Jasiński, Marcin; Wojciechowski, Jakub; Mlostoń, Grzegorz; Albrecht, Łukasz

2017-10-17

The development of the unprecedented ortho-regioselective inverse-electron-demand hetero-Diels-Alder (IEDHDA) reaction is described. It has been demonstrated that by proper choice of reactants and reaction conditions the inverse-electron-demand hetero-Diels-Alder cycloaddition can be realized with unprecedented regioselectivity arising from the reaction between the terminal carbon atom of the dienophile and the heteroatom of the heterodiene.

389 Allergic Reactions to Local Anesthetics: Detection by Skin Tests and Subcutaneous Provocation. Analysis of 160 Cases

Science.gov (United States)

Arcanjo, Luiz; Gonçalves Tavares, Tania Maria; Delcourt, Nathalia; Baroni, Juliana; Rios, João; Rios, José Luiz

2012-01-01

Background Adverse reactions to local anesthetics (LA) are frequent and often referred to as allergic. Although immune-mediated reactions are rare, it should be investigated for suspected cases. The objective of this study was to determine the frequency of positive skin test to these drugs in patients with a suspected history of allergic reactions and describe the main socio-demographic characteristics of these individuals. Methods Retrospective study of medical records of patients attended at Policlínica Geral do Rio de Janeiro Allergic Clinic, between 2008 and 2011. The parameters evaluated were the test indication and the patient ages and gender. The drug tested was that the patient had a history of suspicion. Patients underwent skin prick and intradermal tests and subcutaneous provocation. Descriptive statistical analysis of the data was performed. Results It was performed 160 tests (125 female). Three of this total was excluded due to inconclusive results. In women, the highest proportion of tests was in the age group from 41 to 60 years (43%), while in males the higher concentration was at a youngest age group: 21 to 40 years (41%). The most common indication (103 cases, 65%) for the tests was a previous suspected anaphylactic reaction by LA. Seven of 157 tests had a positive result (4.4%), 6 of them occurred in women (4.8%). Only one test resulted in a type of anaphylactic reaction response (0.67%). All patients who presented positive response to the test had a history of per-anesthetic reaction that suggested an immune-mediated mechanism. Conclusions In patients with a history of previous reaction to local anesthetics, the skin tests with these drugs have a key role in the prevention of anaphylaxis, and on guidance for adequate anesthetic procedures.

Clinical features of severe wasp sting patients with dominantly toxic reaction: analysis of 1091 cases.

Directory of Open Access Journals (Sweden)

Cuihong Xie

Full Text Available BACKGROUND: Massive wasp stings have been greatly underestimated and have not been systematically studied. The aim of this study was to identify the clinical features and treatment strategies of severe wasp stings. METHODS AND FINDINGS: A multicenter retrospective study was undertaken in 35 hospitals and medical centers including 12 tertiary care hospitals and 23 secondary care hospitals in the Hubei Province, China. The detailed clinical data of 1091 hospitalized wasp sting patients were investigated. Over three-fourths (76.9% of the cases had 10 or more stings and the in-hospital mortality of patients was 5.1%. Forty-eight patients died of organ injury following toxic reactions to the stings, whereas six died from anaphylactic shock. The in-hospital mortality in patients with >10 stings was higher than that of ≤10 stings (5.2% vs. 1.0%, p = 0.02. Acute kidney injury (AKI was seen in 21.0% patients and most patients required blood purification therapy. Rhabdomyolysis was seen in 24.1% patients, hemolysis in 19.2% patients, liver injury in 30.1% patients, and coagulopathy in 22.5% patients. Regression analysis revealed that high creatinine level, shock, oliguria, and anemia were risk factors for death. Blood purification therapy was beneficial for patients with ≥20 stings and delayed hospital admission of patients (≥4 hours after sting. CONCLUSIONS: In China, most patients with multiple wasp stings presented with toxic reactions and multiple organ dysfunction caused by the venom rather than an anaphylactic reaction. AKI is the prominent clinical manifestation of wasp stings with toxic reaction. High creatinine levels, shock, oliguria, and anemia were risk factors for death.

Community College Recruitment: An Analysis of Applicant Reactions.

Science.gov (United States)

Winter, Paul A.; Kjorlien, Chad L.

The purpose of this study was to: (1) conduct an empirical examination of applicant reactions to faculty jobs described in recruitment advertisements for business faculty vacancies at community colleges; and (2) assess factors that potentially impact applicant decisions to apply for and pursue position vacancies. The results of this study have…

CHEMICAL REACTIONS ON ADSORBING SURFACE: KINETIC LEVEL OF DESCRIPTION

Directory of Open Access Journals (Sweden)

P.P.Kostrobii

2003-01-01

Full Text Available Based on the effective Hubbard model we suggest a statistical description of reaction-diffusion processes for bimolecular chemical reactions of gas particles adsorbed on the metallic surface. The system of transport equations for description of particles diffusion as well as reactions is obtained. We carry out the analysis of the contributions of all physical processes to the formation of diffusion coefficients and chemical reactions constants.

Erythema-index of clinical patch test reactions

DEFF Research Database (Denmark)

Jemec, G B; Johansen, J D

1995-01-01

that the method could be used for the grading of eczematous reactions in a clinical setting as well. OBJECTIVE: To assess the usefulness of the erythema index for the quantification of eczematous reactions using the Derma-Spectrometer (Cortex technology, Hadsund, Denmark) in a clinical setting. METHOD......: The erythema index of 56 patch test reactions ranging from +? to +++, was compared to regional controls and negative patch tests (189). The effects of intrumental application pressure was studied in 5 volunteers. Statistical analysis was carried out using Mann-Whitney and Jonckheere-Terpstra tests. RESULTS......: The erythema-index was significantly higher in all degrees of patch test reactions than in uninvolved regional skin or negative patch tests. It also showed a significant positive trend for higher values in +, ++ and +++ reactions (P

One-nucleon pickup reactions and compound-nuclear decays

Science.gov (United States)

Escher, J. E.; Burke, J. T.; Casperson, R. J.; Hughes, R. O.; Scielzo, N. D.

2018-05-01

One-nucleon transfer reactions, long used as a tool to study the structure of nuclei, are potentially valuable for determining reaction cross sections indirectly. This is significant, as many reactions of interest to astrophysics and other applications involve short-lived isotopes and cannot be measured directly. We describe a procedure for obtaining constraints for calculations of neutron capture cross sections using observables from experiments with transfer reactions. As a first step toward demonstrating the method, we outline the theory developments used to properly describe the production of the compound nucleus 88Y* via the one-nucleon pickup reaction 89Y(p,d)88Y* and test the description with data from a recent experiment. We indicate how this development can be used to extract the unknown 87Y(n,γ) cross section from 89Y(p,dγ) data. The example illustrates a more generally applicable method for determining unknown cross sections via a combination of theory and transfer (or inelastic scattering) experiments.

Thermodynamic analysis and experimental study on the chlorination of uranium oxide by gas-solid reaction

International Nuclear Information System (INIS)

Shin, Y.J.; Kim, I.S.; Shin, H.S.; Ro, S.G.; Park, H.S.

1998-01-01

In order to determine the operating condition of an uranium chlorination process with U 3 O 8 -C-Cl 2 system, the experimental conditions have been evaluated preliminarily by the thermochemical analysis and experimentally confirmed in this study. The dry-type chlorination of U 3 O 8 occurs as irreversible and exothermic reaction and produces many kinds of chloride compounds such as UCl 3 , UCl 4 , UCl 5 , and UCl 6 in the air and humidity controlled argon environment. Taking account of Gibbs free energy and vapor pressure for various chloride compounds, the proper temperature range of chlorination appears to be 863 to 953 K in aspects of increasing reaction rate and the yield of nonvolatile product. In the course of the experimental confirmation the powder of U 3 O 8 is perfectly converted into uranium chlorides within 4 hours above 863 K, and then the maximum fraction of uranium chloride remaining in the reactor is about 30% of total conversion mass. (author)

Demonstration of a software design and statistical analysis methodology with application to patient outcomes data sets.

Science.gov (United States)

Mayo, Charles; Conners, Steve; Warren, Christopher; Miller, Robert; Court, Laurence; Popple, Richard

2013-11-01

With emergence of clinical outcomes databases as tools utilized routinely within institutions, comes need for software tools to support automated statistical analysis of these large data sets and intrainstitutional exchange from independent federated databases to support data pooling. In this paper, the authors present a design approach and analysis methodology that addresses both issues. A software application was constructed to automate analysis of patient outcomes data using a wide range of statistical metrics, by combining use of C#.Net and R code. The accuracy and speed of the code was evaluated using benchmark data sets. The approach provides data needed to evaluate combinations of statistical measurements for ability to identify patterns of interest in the data. Through application of the tools to a benchmark data set for dose-response threshold and to SBRT lung data sets, an algorithm was developed that uses receiver operator characteristic curves to identify a threshold value and combines use of contingency tables, Fisher exact tests, Welch t-tests, and Kolmogorov-Smirnov tests to filter the large data set to identify values demonstrating dose-response. Kullback-Leibler divergences were used to provide additional confirmation. The work demonstrates the viability of the design approach and the software tool for analysis of large data sets.

Measurement and analysis of double-differential neutron emission spectra in (P,N) and (α,N) reactions

International Nuclear Information System (INIS)

Okamoto, K.; Mehta, M.K.

1988-05-01

The second IAEA Research Co-ordination Meeting on Measurement and Analysis of Double-Differential Neutron Emission Spectra in (p,n) and (α,n) Reactions was convened by the IAEA Nuclear Data Section at the IAEA Headquarters in Vienna during 8-10 February, 1988. The main objectives of the Co-ordinated Research Project for which this meeting was held are (i) to extract systematic information about nuclear level densities as a function of excitation energy by analysing the neutron emission spectra from (p,n) and (α,n) reactions on properly selected targets and bombarding energy range, and (ii) to parametrize this information into appropriate phenomenological models to enable reliable extrapolation for general use of level density information in basic and applied nuclear physics related problems. Detailed conclusions and recommendations, together with a summary of the programme during 1988/1989 are attached in the Appendices

Neuroendocrine and cardiovascular reactions to acute psychological stress are attenuated in smokers

NARCIS (Netherlands)

Ginty, Annie T.; Jones, Alexander; Carroll, Douglas; Roseboom, Tessa J.; Phillips, Anna C.; Painter, Rebecca; de Rooij, Susanne R.

2014-01-01

A number of studies have now examined the association between smoking and the magnitude of physiological reactions to acute psychological stress. However, no large-scale study has demonstrated this association incorporating neuroendocrine in addition to cardiovascular reactions to stress. The

Diagnostic value of polymerase chain reaction analysis of skin biopsies in purpura fulminans.

Science.gov (United States)

Beau, Caroline; Vlassova, Natalia; Sarlangue, Jean; Brissaud, Olivier; Léauté-Labrèze, Christine; Boralevi, Franck

2013-01-01

Even though prompt diagnosis and treatment of purpura fulminans (PF) is essential to reduce mortality, early administration of antibiotics may preclude identification of the causative agent by standard bacterial cultures and thus render definitive diagnosis impossible. Here we present a case of an infant with PF and negative bacterial cultures for whom polymerase chain reaction (PCR) analysis of a cutaneous biopsy specimen obtained 4 days after initiation of antibiotics identified the genomic sequence of Neisseria meningitidis genogroup C. When bacterial cultures fail to provide useful information, PCR of skin biopsy specimens can be a valuable diagnostic tool in PF. © 2013 Wiley Periodicals, Inc.

Monotectic four-phase reaction in Al-Bi-Zn alloys

Energy Technology Data Exchange (ETDEWEB)

Groebner, J. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Mirkovic, D. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Schmid-Fetzer, R. [Clausthal University of Technology, Institute of Metallurgy, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany)]. E-mail: schmid-fetzer@tu-clausthal.de

2005-06-15

Thermodynamic phase diagram calculations were used for the systematic search for a monotectic four-phase reaction in ternary Al-alloys. Systems with intermetallic phases and also the elements Cd and Hg were excluded in the present search. The ternary Al-Bi-Zn is a rare occasion where such a reaction, L' = L' + (Al)' + (Zn), actually occurs. Experimental work could be focused on key samples in that system and involved DSC for thermal analysis and calorimetry, and also metallographic analysis using SEM/EDX. Experimental results verify the existence of the monotectic reaction and were also used for a quantitative thermodynamic modeling of Al-Bi-Zn. Solidification paths and microstructures of Al-Bi-Zn alloys are shown to be rather complex. Using thermodynamic calculations, these rich details involving up to three invariant reactions and unexpected monovariant reaction types can be clearly revealed and understood.

Gas Chromatographic-Ion Trap Mass Spectrometric Analysis of Volatile Organic Compounds by Ion-Molecule Reactions Using the Electron-Deficient Reagent Ion CCl{3/+}

Science.gov (United States)

Wang, Cheng-Zhong; Su, Yue; Wang, Hao-Yang; Guo, Yin-Long

2011-10-01

When using tetrachloromethane as the reagent gas in gas chromatography-ion trap mass spectrometry equipped with hybrid ionization source, the cation CCl{3/+} was generated in high abundance and further gas-phase experiments showed that such an electron-deficient reagent ion CCl{3/+} could undergo interesting ion-molecule reactions with various volatile organic compounds, which not only present some informative gas-phase reactions, but also facilitate qualitative analysis of diverse volatile compounds by providing unique mass spectral data that are characteristic of particular chemical structures. The ion-molecule reactions of the reagent ion CCl{3/+} with different types of compounds were studied, and results showed that such reactions could give rise to structurally diagnostic ions, such as [M + CCl3 - HCl]+ for aromatic hydrocarbons, [M - OH]+ for saturated cyclic ether, ketone, and alcoholic compounds, [M - H]+ ion for monoterpenes, M·+ for sesquiterpenes, [M - CH3CO]+ for esters, as well as the further fragment ions. The mechanisms of ion-molecule reactions of aromatic hydrocarbons, aliphatic ketones and alcoholic compounds with the reagent ion CCl{3/+} were investigated and proposed according to the information provided by MS/MS experiments and theoretical calculations. Then, this method was applied to study volatile organic compounds in Dendranthema indicum var. aromaticum and 20 compounds, including monoterpenes and their oxygen-containing derivatives, aromatic hydrocarbon and sesquiterpenes were identified using such ion-molecule reactions. This study offers a perspective and an alternative tool for the analysis and identification of various volatile compounds.

Reaction of uranium and the fluorocarbon FC-75

Science.gov (United States)

Young, R. H.

1985-04-01

Because of criticality concerns with water cooling in enriched uranium upgrading, a fluorocarbon has been evaluated as a replacement coolant for internal module components in the Plasma Separation Process (PSP). The interaction of bulk uranium and of powdered uranium with FC-75 has been investigated at temperatures between 200 and 700 C. The gas pressure and the metal temperature were monitored as a function of time. Modest temperature changes of 50 to 100 C were observed for the bulk uranium/fluorocarbon reaction. Much larger changes (up to 1000 C) were noted for the reaction involving high surface area uranium powder. These temperature transients, particularly for the powdered uranium reaction, were short-lived ( 10 seconds) and indicative of the formation of a protective layer of reaction products. Analysis of residual gas products by infrared spectroscopy indicated that one potentially serious hazard, UF6, was not present; however, several small toxic fluorocarbons were produced by thermolysis and/or reaction. X-ray diffraction analysis of the residual solids indicated UF4 and UO2 were the major solid products.

Novel Role of Superfluidity in Low-Energy Nuclear Reactions.

Science.gov (United States)

Magierski, Piotr; Sekizawa, Kazuyuki; Wlazłowski, Gabriel

2017-07-28

We demonstrate, within symmetry unrestricted time-dependent density functional theory, the existence of new effects in low-energy nuclear reactions which originate from superfluidity. The dynamics of the pairing field induces solitonic excitations in the colliding nuclear systems, leading to qualitative changes in the reaction dynamics. The solitonic excitation prevents collective energy dissipation and effectively suppresses the fusion cross section. We demonstrate how the variations of the total kinetic energy of the fragments can be traced back to the energy stored in the superfluid junction of colliding nuclei. Both contact time and scattering angle in noncentral collisions are significantly affected. The modification of the fusion cross section and possibilities for its experimental detection are discussed.

Prevention and treatment of acute radiation-induced skin reactions: a systematic review and meta-analysis of randomized controlled trials

International Nuclear Information System (INIS)

Chan, Raymond Javan; Webster, Joan; Chung, Bryan; Marquart, Louise; Ahmed, Muhtashimuddin; Garantziotis, Stuart

2014-01-01

Radiation-induced skin reaction (RISR) is a common side effect that affects the majority of cancer patients receiving radiation treatment. RISR is often characterised by swelling, redness, pigmentation, fibrosis, and ulceration, pain, warmth, burning, and itching of the skin. The aim of this systematic review was to assess the effects of interventions which aim to prevent or manage RISR in people with cancer. We searched the following databases up to November 2012: Cochrane Skin Group Specialised Register, CENTRAL (2012, Issue 11), MEDLINE (from 1946), EMBASE (from 1974), PsycINFO (from 1806), CINAHL (from 1981) and LILACS (from 1982). Randomized controlled trials evaluating interventions for preventing or managing RISR in cancer patients were included. The primary outcomes were development of RISR, and levels of RISR and symptom severity. Secondary outcomes were time taken to develop erythema or dry desquamation; quality of life; time taken to heal, a number of skin reaction and symptom severity measures; cost, participant satisfaction; ease of use and adverse effects. Where appropriate, we pooled results of randomized controlled trials using mean differences (MD) or odd ratios (OR) with 95% confidence intervals (CI). Forty-seven studies were included in this review. These evaluated six types of interventions (oral systemic medications; skin care practices; steroidal topical therapies; non-steroidal topical therapies; dressings and other). Findings from two meta-analyses demonstrated significant benefits of oral Wobe-Mugos E for preventing RISR (OR 0.13 (95% CI 0.05 to 0.38)) and limiting the maximal level of RISR (MD -0.92 (95% CI -1.36 to -0.48)). Another meta-analysis reported that wearing deodorant does not influence the development of RISR (OR 0.80 (95% CI 0.47 to 1.37)). Despite the high number of trials in this area, there is limited good, comparative research that provides definitive results suggesting the effectiveness of any single intervention for

Inverse-Electron-Demand Diels-Alder Reactions: Principles and Applications.

Science.gov (United States)

Png, Zhuang Mao; Zeng, Huining; Ye, Qun; Xu, Jianwei

2017-09-05

Inverse-electron-demand Diels-Alder (iEDDA) reactions are an intriguing class of cycloaddition reactions that have attracted increasing attention for their application in bioorthogonal chemistry, the total synthesis of natural products, and materials science. In many cases, the application of the iEDDA reaction has been demonstrated as an innovative approach to achieve target structures. The theoretical aspects of this class of reactions are of particular interest for scientists as a means to understand the various factors, such as steric strain and electron density of the attached groups, that govern the reaction and thus to elucidate the reaction mechanism. This review aims to summarize both theoretical investigations and application-driven research work on the iEDDA reaction. First, the historical aspects and the theoretical basis of the reaction, especially recent advances in time-dependent density functional theory (TD-DFT) calculations, as well as catalysis strategies will be highlighted and discussed. Second, the applications of this novel reaction in the context of materials science, bioorthogonal chemistry, and total synthesis of natural products will be elaborated with selected recent examples. The challenges and opportunities of the iEDDA reaction will be highlighted to give more insight into its potential applications in many other research areas. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Consistent analysis of peripheral reaction channels and fusion for the 16,18O+58Ni systems

International Nuclear Information System (INIS)

Alves, J.J.S.; Gomes, P.R.S.; Lubian, J.; Chamon, L.C.; Pereira, D.; Anjos, R.M.; Rossi, E.S.; Silva, C.P.; Alvarez, M.A.G.; Nobre, G.P.A.; Gasques, L.R.

2005-01-01

We have measured elastic scattering and peripheral reaction channel cross sections for the 16,18 O+ 58 Ni systems at ELab=46 MeV. The data were analyzed through extensive coupled-channel calculations. It was investigated the consistency of the present analysis with a previous one at sub-barrier energies. Experimental fusion cross sections for these systems are also compared with the corresponding predictions of the coupled-channel calculations

Characterization of ESIPT reactions with instant spectra of fluorescence and complexation processes

International Nuclear Information System (INIS)

Tomin, Vladimir I.; Ushakou, Dzmitryi V.

2016-01-01

Proton transfer processes and especially excited-state intramolecular proton transfer (ESIPT) are of interest not only in physical studies but in a wide range of biological and chemical researches, since they play an important role in different fundamental reactions. Moreover, occurrence of ESIPT very often causes two-bands emission spectra corresponding to the normal and photoproduct (tautomer) forms of molecular structure. It allows carrying out unique measurement of microcharacteristics in chemical and biological researches by using substances with ESIPT as molecular probes, because its dual emission is very sensitive to parameters of microenvironment. Dual fluorescence signal is very convenient for two wavelength ratiometric measurements as they are more sensitive to variations of sample characteristics. Recently new approach for revealing type of excited state reaction which is based on analysis of dynamic changes of relative intensities in instant spectra of fluorescence ESIPT solutes was suggested and tested for neat solutions. Now we generalize this method on solutions in which ESIPT solute may participate also in creating fluorescent complexes. We demonstrate that relative intensities of instant spectra of fluorescence registered with high time resolution allow to get valuable information referring to type of excited state reaction in which dye may undergo complexation reactions with ions in solvent. In addition we show how it is possible in such case to determine characteristics of complexation as, for example, stability constant and efficiency of complexation.

Stoichiometric Representation of Gene–Protein–Reaction Associations Leverages Constraint-Based Analysis from Reaction to Gene-Level Phenotype Prediction