RCRA Facilities Assessment (RFA)---Oak Ridge National Laboratory

International Nuclear Information System (INIS)

1987-03-01

US Department of Energy (DOE) facilities are required to be in full compliance with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established a Remedial Action Program (RAP) to provide comprehensive management of areas where past and current research, development, and waste management activities have resulted in residual contamination of facilities or the environment. This report presents the RCRA Facility Assessment (RFA) required to meet the requirements of RCRA Section 3004(u). Included in the RFA are (1) a listing of all sites identified at ORNL that could be considered sources of releases or potential releases; (2) background information on each of these sites, including location, type, size, period of operation, current operational status, and information on observed or potential releases (as required in Section II.A.1 of the RCRA permit); (3) analytical results obtained from preliminary surveys conducted to verify the presence or absence of releases from some of the sites; and (4) ORNL's assessment of the need for further remedial attention

RCRA Facilities Assessment (RFA)---Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

1987-03-01

US Department of Energy (DOE) facilities are required to be in full compliance with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established a Remedial Action Program (RAP) to provide comprehensive management of areas where past and current research, development, and waste management activities have resulted in residual contamination of facilities or the environment. This report presents the RCRA Facility Assessment (RFA) required to meet the requirements of RCRA Section 3004(u). Included in the RFA are (1) a listing of all sites identified at ORNL that could be considered sources of releases or potential releases; (2) background information on each of these sites, including location, type, size, period of operation, current operational status, and information on observed or potential releases (as required in Section II.A.1 of the RCRA permit); (3) analytical results obtained from preliminary surveys conducted to verify the presence or absence of releases from some of the sites; and (4) ORNL`s assessment of the need for further remedial attention.

RCRA Facilities Assessment (RFA)---Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

1987-03-01

US Department of Energy (DOE) facilities are required to be in full compliance with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established a Remedial Action Program (RAP) to provide comprehensive management of areas where past and current research, development, and waste management activities have resulted in residual contamination of facilities or the environment. This report presents the RCRA Facility Assessment (RFA) required to meet the requirements of RCRA Section 3004(u). Included in the RFA are (1) a listing of all sites identified at ORNL that could be considered sources of releases or potential releases; (2) background information on each of these sites, including location, type, size, period of operation, current operational status, and information on observed or potential releases (as required in Section II.A.1 of the RCRA permit); (3) analytical results obtained from preliminary surveys conducted to verify the presence or absence of releases from some of the sites; and (4) ORNL's assessment of the need for further remedial attention.

NPL deletion policy for RCRA-regulated TSD facilities finalized

International Nuclear Information System (INIS)

Anon.

1995-01-01

Under a new policy published by EPA on March 20, 1995, certain sites may be deleted from the National Priorities List (NPL) and deferred to RCRA corrective action. To be deleted from the NPL, a site must (1) be regulated under RCRA as a treatment, storage, or disposal (TSD) facility and (2) meet the four criteria specified by EPA. The new NPL deletion policy, which does not pertain to federal TSD facilities, became effective on April 19, 1995. 1 tab

RCRA closures at Rocky Flats Plant: A programmatic perspective and case study

International Nuclear Information System (INIS)

Ogg, Randy T.; Peterman, Bruce D.

1992-01-01

The Interagency Agreement (IAG) integrates a unique mechanism for remediating hazardous waste sites at the Rocky Flats Plant (RFP), which include utilizing RCRA and CERCLA technical/regulatory processes. Pursuant to the IAG signed by the Department of Energy (DOE), Environmental Protection Agency (EPA), and the Colorado Department of Health (CDH) on January 22, 1991, sixteen operable units (OUs) were defined for characterization and remediation at RFP. Of the sixteen OUs, six are classified as Resource Conservation and Recovery Act (RCRA) closure units. The six RCRA interim status closure units are: Solar Evaporation Ponds-OU 4, Present LandfUl-OU 7, Original Process Waste Lines-OU 9, Other Outside Closures-OU 10, West Spray Field-OU II, and Inside Building Closures-OU 15. The IAG will function as a technical/regulatory mechanism for managing/complying with all aspects of the RCRA interim status closure units at RFP. (author)

Implementing RCRA during facility deactivation

International Nuclear Information System (INIS)

Lebaron, G.J.

1997-01-01

RCRA regulations require closure of permitted treatment, storage and disposal (TSD) facilities within 180 days after cessation of operations, and this may essentially necessitate decommissioning to complete closure. A more cost effective way to handle the facility would be to significantly reduce the risk to human health and the environment by taking it from its operational status to a passive, safe, inexpensive-to-maintain surveillance and maintenance condition (deactivation) prior to decommissioning. This paper presents an innovative approach to the cost effective deactivation of a large, complex chemical processing facility permitted under RCRA. The approach takes into account risks to the environment posed by this facility in comparison to risks posed by neighboring facilities at the site. The paper addresses the manner in which: 1) stakeholders and regulators were involved; 2) identifies a process by which the project proceeds and regulators and stakeholders were involved; 3) end points were developed so completion of deactivation was clearly identified at the beginning of the project, and 4) innovative practices were used to deactivate more quickly and cost effectively

Resource Conservation and Recovery Act (RCRA)

International Nuclear Information System (INIS)

1989-01-01

This Resource Conservation and Recovery Act (RCRA) Facility Investigation Program Plan has been developed to provide a framework for the completion of RCRA Facility Investigations (RFI) at identified units on the Savannah Rive Site (SRS) facility. As such, the RFI Program Plan provides: technical guidance for all work to be performed, managerial control, a practical, scientific approach. The purpose of this Overview is to demonstrate how the basic RFI Program Plan elements (technical, management, and approach) are interwoven to provide a practical and workable plan. The goal of the RFI Program Plan is to provide a systematic, uniform approach for performance and reporting. In addition, the RFI Program Plan has been developed to be specific to the SRS facility and to adhere to the Environmental Protection Agency (EPA) RFI guidance received as part of the SRS. The US EPA publication ''Characterization of Hazardous Waste Sites'' has been liberally adapted for use in this RFI Program Plan

Quarterly RCRA Groundwater Monitoring Data for the Period April Through June 2006

Energy Technology Data Exchange (ETDEWEB)

Hartman, Mary J.

2006-11-01

This report provides information about RCRA groundwater monitoring for the period April through June 2006. Seventeen RCRA sites were sampled during the reporting quarter. Sampled sites include seven monitored under groundwater indicator evaluation (''detection'') programs, eight monitored under groundwater quality assessment programs, and two monitored under final-status programs.

RCRA Treatment, Disposal, and Storage Site Boundaries in Louisiana, Geographic NAD83, EPA (2002) [RCRA_TSD_LA_poly_EPA_2002)

Data.gov (United States)

Louisiana Geographic Information Center — This is a shapefile of RCRA Treatment, Storage, and Disposal facility boundaries developed by PRC Environmental Management, Inc (PRC) per a Work Assignment from the...

EPA seeks to make RCRA more effective through legislative changes

International Nuclear Information System (INIS)

Anon.

1995-01-01

Since RCRA was enacted in 1976 and amended in 1984, hazardous waste management has been transformed. To protect human health and the environment as mandated by the act, EPA has developed a complex cradle-to-grave system for managing hazardous waste. The agency recognizes that some targeted legislative changes could make RCRA even more useful, particularly by (1) establishing some open-quotes middle groundclose quotes for waste posing low risks, and (2) emphasizing sensible and enforceable hazardous waste management practices

Achieving RCRA compliance in DOE defense waste management operations

International Nuclear Information System (INIS)

Frankhauser, W.A.; Shepard, M.D.

1989-01-01

The U.S. Department of Energy (DOE) generates significant volumes of radioactive mixed waste (RMW) through its defense-related activities. Defense RMW is co-regulated by DOE and the U.S. Environmental Protection Agency/State agencies in accordance with requirements of the Resource Conservation and Recovery Act (RCRA) and the Atomic Energy Act (AEA). This paper highlights some of the problems encountered in co-regulation and discusses achievements of the defense waste management program in integrating RCRA requirements into RMW operations. Defense waste sites are planning facility modifications and major new construction projects to develop treatment, storage and disposal capacity for existing RMW inventories and projected needs

National RCRA Hazardous Waste Biennial Report Data Files

Science.gov (United States)

The United States Environmental Protection Agency (EPA), in cooperation with the States, biennially collects information regarding the generation, management, and final disposition of hazardous wastes regulated under the Resource Conservation and Recovery Act of 1976 (RCRA), as amended. Collection, validation and verification of the Biennial Report (BR) data is the responsibility of RCRA authorized states and EPA regions. EPA does not modify the data reported by the states or regions. Any questions regarding the information reported for a RCRA handler should be directed to the state agency or region responsible for the BR data collection. BR data are collected every other year (odd-numbered years) and submitted in the following year. The BR data are used to support regulatory activities and provide basic statistics and trend of hazardous waste generation and management. BR data is available to the public through 3 mechanisms. 1. The RCRAInfo website includes data collected from 2001 to present-day (https://rcrainfo.epa.gov/rcrainfoweb/action/main-menu/view). Users of the RCRAInfo website can run queries and output reports for different data collection years at this site. All BR data collected from 2001 to present-day is stored in RCRAInfo, and is accessible through this website. 2. An FTP site allows users to access BR data files collected from 1999 - present day (ftp://ftp.epa.gov/rcrainfodata/). Zip files are available for download directly from this

Glossary of CERCLA, RCRA and TSCA related terms and acronyms

International Nuclear Information System (INIS)

1993-10-01

This glossary contains CERCLA, RCRA and TSCA related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The CERCLA definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended and related federal rulemakings. The RCRA definitions included in this glossary are taken from the Resource Conservation and Recovery Act (RCRA) and related federal rulemakings. The TSCA definitions included in this glossary are taken from the Toxic Substances and Control Act (TSCA) and related federal rulemakings. Definitions related to TSCA are limited to those sections in the statute and regulations concerning PCBs and asbestos.Other sources for definitions include additional federal rulemakings, assorted guidance documents prepared by the US Environmental Protection Agency (EPA), guidance and informational documents prepared by the US Department of Energy (DOE), and DOE Orders. The source of each term is noted beside the term. Terms presented in this document reflect revised and new definitions published before July 1, 1993

Analysis of TRU waste for RCRA-listed elements

International Nuclear Information System (INIS)

Mahan, C.; Gerth, D.; Yoshida, T.

1996-01-01

Analytical methods for RCRA listed elements on Portland cement type waste have been employed using both microwave and open hot plate digestions with subsequent analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES), inductively coupled plasma mass spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS), graphite furnace atomic absorption (GFAA) and cold vapor atomic absorption and fluorescence (CVAA/CVAFS). Four different digestion procedures were evaluated including an open hot plate nitric acid digestion, EPA SW-846 Method 3051, and 2 methods using modifications to Method 3051. The open hot plate and the modified Method 3051, which used aqua regia for dissolution, were the only methods which resulted in acceptable data quality for all 14 RCRA-listed elements. Results for the nitric acid open hot plate digestion were used to qualify the analytical methods for TRU waste characterization, and resulted in a 99% passing score. Direct chemical analysis of TRU waste is being developed at Los Alamos National Laboratory in an attempt to circumvent the problems associated with strong acid digestion methods. Technology development includes laser induced breakdown spectroscopy (LIBS), laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS), dc arc CID atomic emission spectroscopy (DC-AES), and glow discharge mass spectrometry (GDMS). Analytical methods using the Portland cement matrix are currently being developed for each of the listed techniques. Upon completion of the development stage, blind samples will be distributed to each of the technology developers for RCRA metals characterization

Hanford facility RCRA permit condition II.U.1 report: mapping of underground piping

Energy Technology Data Exchange (ETDEWEB)

Hays, C.B.

1996-09-27

The purpose of this report is to fulfill Condition Il.U.1. of the Hanford Facility (HF) Resource Conservation and Recovery Act (RCRA) Permit. The HF RCRA Permit, Number WA7890008967, became effective on September 28, 1994 (Ecology 1994). Permit Conditions Il.U. (mapping) and II.V. (marking) of the HF RCRA Permit, Dangerous Waste (OW) Portion, require the mapping and marking of dangerous waste underground pipelines subject to the provisions of the Washington Administrative Code (WAC) Chapter 173-303. Permit Condition Il.U.I. requires the submittal of a report describing the methodology used to generate pipeline maps and to assure their quality. Though not required by the Permit, this report also documents the approach used for the field marking of dangerous waste underground pipelines.

SACM and the RCRA stabilization initiative: Similarities of principles and applicability

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and the corrective action provisions of the Resource Conservation and Recovery Act (RCRA) provide standards for the remediation of environmental media contaminated with hazardous substances or hazardous waste, respectively. In both cases, prior to the US Environmental Protection Agency`s (EPA) development of the two subject reform initiatives, existing formal processes specified the level of site investigation required, the process for reaching a decision on the method of remediation, public participation in the decision process, and enforcement authorities that include orders and schedules of compliance. Traditionally, implementation of these processes has resulted in a great amount of time, effort, and money being expended before actual remediation began. Following criticism from the public and the regulated community, the EPA has proposed streamlining reforms for hazardous waste site cleanup under both CERCLA and RCRA that will begin remediation sooner with lower costs. The purpose of this Information Brief is to discuss the common goals, processes, and strategies of the Superfund Accelerated Cleanup Model (SACM) and the RCRA Stabilization Initiative.

The implications of RCRA [Resource Conservation and Recovery Act] regulation for the disposal of transuranic and high-level waste

International Nuclear Information System (INIS)

Sigmon, C.F.; Sharples, F.E.; Smith, E.D.

1988-01-01

In May of 1987 the Department of Energy (DOE) published a rule interpreting the definition of ''byproduct'' under the Atomic Energy Act. This byproduct rule clarified the role of the Resource Conservation and Recovery Act (RCRA) in the regulation of DOE's radioactive waste management activities. According to the rule, only the radioactive portion of DOE's mixed radioactive and hazardous waste (mixed waste), including mixed transuranic (TRU) and high-level waste (HLW), is exempt from RCRA under the byproduct exemption. The portion of a waste that is hazardous as defined by RCRA is subject to full regulation under RCRA. Because the radioactive and hazardous portions of m any, if not most, DOE wastes are likely to be inseparable, the rule in effect makes most mixed wastes subject to dual regulation. The potential application of RCRA to facilities such as the Waste Isolation Pilot Plant (WIPP) and the HLW repository creates unique challenges for both the DOE and regulatory authorities. Strategies must be developed to assure compliance with RCRA without either causing excessive administrative burdens or abandoning the goal of minimizing radiation exposure. This paper will explore some of the potential regulatory options for and recent trends in the regulation of TRU and HLW under RCRA

Selective removal/recovery of RCRA metals from waste and process solutions using polymer filtration trademark technology

International Nuclear Information System (INIS)

Smith, B.F.

1997-01-01

Resource Conservation and Recovery Act (RCRA) metals are found in a number of process and waste streams at many DOE, U.S. Department of Defense, and industrial facilities. RCRA metals consist principally of chromium, mercury, cadmium, lead, and silver. Arsenic and selenium, which form oxyanions, are also considered RCRA elements. Discharge limits for each of these metals are based on toxicity and dictated by state and federal regulations (e.g., drinking water, RCRA, etc.). RCRA metals are used in many current operations, are generated in decontamination and decommissioning (D ampersand D) operations, and are also present in old process wastes that require treatment and stabilization. These metals can exist in solutions, as part of sludges, or as contaminants on soils or solid surfaces, as individual metals or as mixtures with other metals, mixtures with radioactive metals such as actinides (defined as mixed waste), or as mixtures with a variety of inert metals such as calcium and sodium. The authors have successfully completed a preliminary proof-of-principle evaluation of Polymer Filtration trademark (PF) technology for the dissolution of metallic mercury and have also shown that they can remove and concentrate RCRA metals from dilute solutions for a variety of aqueous solution types using PF technology. Another application successfully demonstrated is the dilute metal removal of americium and plutonium from process streams. This application was used to remove the total alpha contamination to below 30 pCi/L for the wastewater treatment plant at TA-50 at Los Alamos National Laboratory (LANL) and from nitric acid distillate in the acid recovery process at TA-55, the Plutonium Facility at LANL (ESP-CP TTP AL16C322). This project will develop and optimize the PF technology for specific DOE process streams containing RCRA metals and coordinate it with the needs of the commercial sector to ensure that technology transfer occurs

Selective removal/recovery of RCRA metals from waste and process solutions using polymer filtration{trademark} technology

Energy Technology Data Exchange (ETDEWEB)

Smith, B.F. [Los Alamos National Lab., NM (United States)

1997-10-01

Resource Conservation and Recovery Act (RCRA) metals are found in a number of process and waste streams at many DOE, U.S. Department of Defense, and industrial facilities. RCRA metals consist principally of chromium, mercury, cadmium, lead, and silver. Arsenic and selenium, which form oxyanions, are also considered RCRA elements. Discharge limits for each of these metals are based on toxicity and dictated by state and federal regulations (e.g., drinking water, RCRA, etc.). RCRA metals are used in many current operations, are generated in decontamination and decommissioning (D&D) operations, and are also present in old process wastes that require treatment and stabilization. These metals can exist in solutions, as part of sludges, or as contaminants on soils or solid surfaces, as individual metals or as mixtures with other metals, mixtures with radioactive metals such as actinides (defined as mixed waste), or as mixtures with a variety of inert metals such as calcium and sodium. The authors have successfully completed a preliminary proof-of-principle evaluation of Polymer Filtration{trademark} (PF) technology for the dissolution of metallic mercury and have also shown that they can remove and concentrate RCRA metals from dilute solutions for a variety of aqueous solution types using PF technology. Another application successfully demonstrated is the dilute metal removal of americium and plutonium from process streams. This application was used to remove the total alpha contamination to below 30 pCi/L for the wastewater treatment plant at TA-50 at Los Alamos National Laboratory (LANL) and from nitric acid distillate in the acid recovery process at TA-55, the Plutonium Facility at LANL (ESP-CP TTP AL16C322). This project will develop and optimize the PF technology for specific DOE process streams containing RCRA metals and coordinate it with the needs of the commercial sector to ensure that technology transfer occurs.

Glossary of CERCLA, RCRA and TSCA related terms and acronyms. Environmental Guidance

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This glossary contains CERCLA, RCRA and TSCA related terms that are most often encountered in the US Department of Energy (DOE) Environmental Restoration and Emergency Preparedness activities. Detailed definitions are included for key terms. The CERCLA definitions included in this glossary are taken from the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as amended and related federal rulemakings. The RCRA definitions included in this glossary are taken from the Resource Conservation and Recovery Act (RCRA) and related federal rulemakings. The TSCA definitions included in this glossary are taken from the Toxic Substances and Control Act (TSCA) and related federal rulemakings. Definitions related to TSCA are limited to those sections in the statute and regulations concerning PCBs and asbestos.Other sources for definitions include additional federal rulemakings, assorted guidance documents prepared by the US Environmental Protection Agency (EPA), guidance and informational documents prepared by the US Department of Energy (DOE), and DOE Orders. The source of each term is noted beside the term. Terms presented in this document reflect revised and new definitions published before July 1, 1993.

Obtaining variances from the treatment standards of the RCRA Land Disposal Restrictions

International Nuclear Information System (INIS)

1990-05-01

The Resource Conservation and Recovery Act (RCRA) Land Disposal Restrictions (LDRs) [40 CFR 268] impose specific requirements for treatment of RCRA hazardous wastes prior to disposal. Before the LDRs, many hazardous wastes could be land disposed at an appropriately designed and permitted facility without undergoing treatment. Thus, the LDRs constitute a major change in the regulations governing hazardous waste. EPA does not regulate the radioactive component of radioactive mixed waste (RMW). However, the hazardous waste component of an RMW is subject to RCRA LDR regulations. DOE facilities that manage hazardous wastes (including radioactive mixed wastes) may have to alter their waste-management practices to comply with the regulations. The purpose of this document is to aid DOE facilities and operations offices in determining (1) whether a variance from the treatment standard should be sought and (2) which type (treatability or equivalency) of petition is appropriate. The document also guides the user in preparing the petition. It shall be noted that the primary responsibility for the development of the treatability petition lies with the generator of the waste. 2 figs., 1 tab

RCRA Part A permit characterization plan for the U-2bu subsidence crater. Revision 1

International Nuclear Information System (INIS)

1998-04-01

This plan presents the characterization strategy for Corrective Action Unit (CAU) 109, U-2bu Subsidence Crater (referred to as U-2bu) in Area 2 at the Nevada Test Site (NTS). The objective of the planned activities is to obtain sufficient characterization data for the crater soils and observed wastes under the conditions of the current Resource Conservation and Recovery Act (RCRA) Part A permit. The scope of the characterization plan includes collecting surface and subsurface soil samples with hand augers and for the purpose of site characterization. The sampling strategy is to characterize the study area soils and look for RCRA constituents. Observable waste soils and surrounding crater soils will be analyzed and evaluated according to RCRA closure criteria. Because of the status of the crater a RCRA Part A permit site, acquired radionuclide analyses will only be evaluated in regards to the health and safety of site workers and the disposition of wastes generated during site characterization. The U-2bu Subsidence Crater was created in 1971 by a Lawrence Livermore National Laboratory underground nuclear test, event name Miniata, and was used as a land-disposal unit for radioactive and hazardous waste from 1973 to 1988

Low-level mixed waste: An RCRA perspective for NRC licensees

International Nuclear Information System (INIS)

1990-08-01

The publication presents an overview of RCRA requirements for commercially-generated low-level mixed waste. It is designed for Nuclear Regulatory Commission (NRC) licensees who may not be familiar with EPA regulations that apply to their waste products

EPA Linked Open Data: Resource Conservation and Recovery Act Handlers (RCRA)

Data.gov (United States)

U.S. Environmental Protection Agency — RCRAInfo is EPA’s comprehensive information system that supports the Resource Conservation and Recovery Act (RCRA) of 1976 and the Hazardous and Solid Waste...

RCRA and operational monitoring 1994 fiscal year work plan, WBS 1.5.3

Energy Technology Data Exchange (ETDEWEB)

1993-12-01

RCRA & Operational Monitoring (ROM) Program Office manages the direct funded Resource Conservation Recovery Act (RCRA) and Operational Monitoring under Work Breakdown Structure (WBS) 1.5.3. The ROM Program Office is a Branch of liquid Waste Disposal, a part of Restoration and Remediation of Westinghouse Hanford Company (WHC). The Fiscal Year Work Plan (FYWP) takes it direction from the Multi-Year Program Plan (MYPP). The FYWP provides the near term, enhanced details for the Program Office to use as baseline Cost, Scope and Schedule. Changs Control administered during the fiscal year is against the baseline provided by the FYWP.

RCRA and operational monitoring 1994 fiscal year work plan, WBS 1.5.3

International Nuclear Information System (INIS)

1993-12-01

RCRA ampersand Operational Monitoring (ROM) Program Office manages the direct funded Resource Conservation Recovery Act (RCRA) and Operational Monitoring under Work Breakdown Structure (WBS) 1.5.3. The ROM Program Office is a Branch of liquid Waste Disposal, a part of Restoration and Remediation of Westinghouse Hanford Company (WHC). The Fiscal Year Work Plan (FYWP) takes it direction from the Multi-Year Program Plan (MYPP). The FYWP provides the near term, enhanced details for the Program Office to use as baseline Cost, Scope and Schedule. Changs Control administered during the fiscal year is against the baseline provided by the FYWP

Rocky Flats Solar Evaporation Ponds RCRA hybrid-closure case study

International Nuclear Information System (INIS)

Ogg, R.T.; Everett, L.G.; Cullen, S.J.

1994-01-01

The Solar Evaporation Ponds (SEP)/Operable Unit 4 (OU 4), located at the Rocky Flats Plant (RFP) sixteen miles northwest of Denver, Colorado, is currently undergoing remediation/Resource Conservation and Recovery Act (RCRA) closure in accordance with the Rocky Flats Interagency Agreement (IAG) signed by the US Department of Energy (DOE), US Environmental Protection Agency (EPA) and Colorado Department of Health (CDH) on January 22, 1991. Based on the ''Phase 1'' (source and soils) RCRA Facility Investigation/Remedial Investigation (RFM data and interpretations), the DOE and EG and G Rocky Flats, Inc. (EG and G) have selected a permanent surface engineered/isolation barrier as the technological option for remediation of the SEP. The DOE and EG and G will utilize all natural materials to create an ''impermeable'' barrier/structure to isolate the waste being left in place from impacting human health and the environment for a minimum of 1,000 years. Their rationale for utilizing natural materials is two fold; (1) optimize long term performance of the barrier and; (2) design a structure which will be near maintenance free (passive remediation) for 1,000 years. The DOE and EG and G have taken a proactive approach in providing post closure performance assessment for this RCRA closure action. An integrated monitoring system has been designed which will include monitoring the engineered barrier, vadose zone and ground water systems. Rocky Flats will integrate instrumentation into the permanent engineered barrier which will provide early warning of potential liquid migration through the barrier and into the waste zone

Guide to ground water remediation at CERCLA response action and RCRA corrective action sites

International Nuclear Information System (INIS)

1995-10-01

This Guide contains the regulatory and policy requirements governing remediation of ground water contaminated with hazardous waste [including radioactive mixed waste (RMW)], hazardous substances, or pollutants/contaminants that present (or may present) an imminent and substantial danger. It was prepared by the Office of Environmental Policy and Assistance, RCRA/CERCLA Division (EH-413), to assist Environmental Program Managers (ERPMs) who often encounter contaminated ground water during the performance of either response actions under CERCLA or corrective actions under Subtitle C of RCRA. The Guide begins with coverage of the regulatory and technical issues that are encountered by ERPM's after a CERCLA Preliminary Assessment/Site Investigation (PA/SI) or the RCRA Facility Assessment (RFA) have been completed and releases into the environment have been confirmed. It is based on the assumption that ground water contamination is present at the site, operable unit, solid waste management unit, or facility. The Guide's scope concludes with completion of the final RAs/corrective measures and a determination by the appropriate regulatory agencies that no further response action is necessary

National spent fuel program preliminary report RCRA characteristics of DOE-owned spent nuclear fuel DOE-SNF-REP-002. Revision 3

International Nuclear Information System (INIS)

1995-07-01

This report presents information on the preliminary process knowledge to be used in characterizing all Department of Energy (DOE)-owned Spent Nuclear Fuel (SNF) types that potentially exhibit a Resource Conservation and Recovery Act (RCRA) characteristic. This report also includes the process knowledge, analyses, and rationale used to preliminarily exclude certain SNF types from RCRA regulation under 40 CFR section 261.4(a)(4), ''Identification and Listing of Hazardous Waste,'' as special nuclear and byproduct material. The evaluations and analyses detailed herein have been undertaken as a proactive approach. In the event that DOE-owned SNF is determined to be a RCRA solid waste, this report provides general direction for each site regarding further characterization efforts. The intent of this report is also to define the path forward to be taken for further evaluation of specific SNF types and a recommended position to be negotiated and established with regional and state regulators throughout the DOE Complex regarding the RCRA-related policy issues

National spent fuel program preliminary report RCRA characteristics of DOE-owned spent nuclear fuel DOE-SNF-REP-002. Revision 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This report presents information on the preliminary process knowledge to be used in characterizing all Department of Energy (DOE)-owned Spent Nuclear Fuel (SNF) types that potentially exhibit a Resource Conservation and Recovery Act (RCRA) characteristic. This report also includes the process knowledge, analyses, and rationale used to preliminarily exclude certain SNF types from RCRA regulation under 40 CFR {section}261.4(a)(4), ``Identification and Listing of Hazardous Waste,`` as special nuclear and byproduct material. The evaluations and analyses detailed herein have been undertaken as a proactive approach. In the event that DOE-owned SNF is determined to be a RCRA solid waste, this report provides general direction for each site regarding further characterization efforts. The intent of this report is also to define the path forward to be taken for further evaluation of specific SNF types and a recommended position to be negotiated and established with regional and state regulators throughout the DOE Complex regarding the RCRA-related policy issues.

Decontamination Study for Mixed Waste Storage Tanks RCRA Closure

International Nuclear Information System (INIS)

Leaphart, D.M.; Reed, S.R.; Rankin, W.N.

1995-01-01

The Savannah River Site (SRS) plans to close six underground tanks storing mixed waste under RCRA regulations. In support of this closure effort, a study was performed to determine the optimal method of decontaminating these tanks to meet the closure requirements. Items consaidered in the evaluation of the decontamination methods included effectiveness, compatibility with existing waste residues, possible cleaning solution disposal methods, and cost

CERCLA and RCRA requirements affecting cleanup of a hazardous waste management unit at a Superfund site: A case study

International Nuclear Information System (INIS)

Walsh, T.J.

1995-03-01

The Fernald Environmental Management Project (FEMP) attempted to address both RCRA and CERCLA requirements at the fire training facility (FTF) by integrating a CERCLA removal action work plan with a RCRA closure plan. While the regulatory agencies involved with the FTF cleanup agreed the integrated document was a good idea, implementation proved complicated, owing to disposition of clean debris from a Superfund site, treatment of contaminated media, duration of cleanup activities, and cleanup certification. While all the complications have not been resolved, solutions to all have been proposed to Ohio EPA and U.S. EPA. Both agencies have worked closely with FEMP to find the most effective fulfillment of RCRA and CERCLA requirements

Ground-water monitoring under RCRA

International Nuclear Information System (INIS)

Coalgate, J.

1993-11-01

In developing a regulatory strategy for the disposal of hazardous waste under the Resource Conservation and Recovery Act (RCRA), protection of ground-water resources was the primary goal of the Environmental Protection Agency (EPA). EPA's ground-water protection strategy seeks to minimize the potential for hazardous wastes and hazardous constituents in waste placed in land disposel units to migrate into the environment. This is achieved through liquids management (limiting the placement of liquid wastes in or on the land, requiring the use of liners beneath waste, installing leachate collection systems and run-on and run-off controls, and covering wastes at closure). Ground-water monitoring serves to detect any failure in EPA's liquids management strategy so that ground-water contamination can be detected and addressed as soon as possible

ORGDP RCRA/PCB

International Nuclear Information System (INIS)

Rodgers, T.

1986-01-01

A dual purpose solid/liquid incinerator is currently being constructed at the Oak Ridge Gaseous Diffusion Plant [ORGDP (K-25)] to destroy uranium contaminated, hazardous organic wastes in compliance with the Toxic Substances Control Act (TSCA) and the Resource Conservation and Recovery Act (RCRA). These wastes are generated by the gaseous diffusion plants in Oak Ridge, TN; Paducah, KY; and Portsmouth, OH. In addition, waste will also be received from the Y-12 Plant, Oak Ridge National Laboratory (ORNL), and the Feed Materials Production Center (FMPC). Destruction of PCBs and hazardous liquid organic wastes will be accomplished in a rotary kiln incinerator with an afterburner. This system was selected after a study of various alternatives which are covered in Report No. X-OE-141. Incineration was chosen because it is dependable, permanent, detoxifies organics, and reduces volume. The rotary kiln incinerator was selected because it can thermally destroy organic constituents of liquids, solids, and sludges to produce an organically inert ash. The incineration system, off-gas treatment system, and related instrumentation and controls are being provided by International Waste Energy Systems (IWES) which is responsible for design, construction, startup, and performance testing

Self-assembled monolayers on mosoporous supports (SAMMS) for RCRA metal removal

Energy Technology Data Exchange (ETDEWEB)

Feng, Xiangdong; Liu, Jun; Fryxell, G. [Pacific Northwest National Lab., Richland, WA (United States)

1997-10-01

The Mixed Waste Focus Area has declared mercury removal and stabilization as the first and fourth priorities among 30 prioritized deficiencies. Resource Conservation and Recovery Act (RCRA) metal and mercury removal has also been identified as a high priority at DOE sites such as Albuquerque, Idaho Falls, Oak Ridge, Hanford, Rocky Flats, and Savannah River. Under this task, a proprietary new technology, Self-Assembled Monolayers on Mesoporous Supports (SAMMS), for RCRA metal ion removal from aqueous wastewater and mercury removal from organic wastes such as vacuum pump oils is being developed at Pacific Northwest National Laboratory (PNNL). The six key features of the SAMMS technology are (1) large surface area (>900 m{sup 2}/g) of the mesoporous oxides (SiO{sub 2}, ZrO{sub 2}, TiO{sub 2}) ensures high capacity for metal loading (more than 1 g Hg/g SAMMS); (2) molecular recognition of the interfacial functional groups ensures the high affinity and selectivity for heavy metals without interference from other abundant cations (such as calcium and iron) in wastewater; (3) suitability for removal of mercury from both aqueous wastes and organic wastes; (4) the Hg-laden SAMMS not only pass TCLP tests, but also have good long-term durability as a waste form because the covalent binding between mercury and SAMMS has good resistance to ion exchange, oxidation, and hydrolysis; (5) the uniform and small pore size (2 to 40 nm) of the mesoporous silica prevents bacteria (>2000 nm) from solubilizing the bound mercury; and (6) SAMMS can also be used for RCRA metal removal from gaseous mercury waste, sludge, sediment, and soil.

The WIPP RCRA Part B permit application for TRU mixed waste disposal

International Nuclear Information System (INIS)

Johnson, J.E.

1995-01-01

In August 1993, the New Mexico Environment Department (NMED) issued a draft permit for the Waste Isolation Pilot Plant (WIPP) to begin experiments with transuranic (TRU) mixed waste. Subsequently, the Department of Energy (DOE) decided to cancel the on-site test program, opting instead for laboratory testing. The Secretary of the NMED withdrew the draft permit in 1994, ordering the State's Hazardous and Radioactive Waste Bureau to work with the DOE on submittal of a revised permit application. Revision 5 of the WIPP's Resource Conservation and Recovery Act (RCRA) Part B Permit Application was submitted to the NMED in May 1995, focusing on disposal of 175,600 m 3 of TRU mixed waste over a 25 year span plus ten years for closure. A key portion of the application, the Waste Analysis Plan, shifted from requirements to characterize a relatively small volume of TRU mixed waste for on-site experiments, to describing a complete program that would apply to all DOE TRU waste generating facilities and meet the appropriate RCRA regulations. Waste characterization will be conducted on a waste stream basis, fitting into three broad categories: (1) homogeneous solids, (2) soil/gravel, and (3) debris wastes. Techniques used include radiography, visually examining waste from opened containers, radioassay, headspace gas sampling, physical sampling and analysis of homogeneous wastes, and review of documented acceptable knowledge. Acceptable knowledge of the original organics and metals used, and the operations that generated these waste streams is sufficient in most cases to determine if the waste has toxicity characteristics, hazardous constituents, polychlorinated biphenyls (PBCs), or RCRA regulated metals

RCRA corrective action for underground storage tanks -- Subtitle C for Subtitle I

International Nuclear Information System (INIS)

1995-08-01

The purpose of this report is to provide guidance to DOE and DOE contractor personnel responsible for planning and implementation of corrective measures addressing cleanup of releases of hazardous materials or regulated substances from underground storage tanks regulated under RCRA Subtitle C or Subtitle I

RCRA, a state perspective: the buck should stop with us

Energy Technology Data Exchange (ETDEWEB)

McCall, III, M N

1977-11-01

The states must carry the ball of realizing the Resource Conservation and Recovery Act (RCRA); state agencies and the EPA can work together, though they don't always agree; adequate funding is absolutely necessary. The states' perspective of their role is threefold-regulation, assistance, and leadership, with maximum input into implementation. A National Governors' Association committee on waste management was established. Neither RCRA itself nor supporting committee reports allow definition of open dumps and sanitary landfills with other than traditional meaning. Conducting the open dump inventory should be the responsibility of the states, with financial support from EPA. The existence of state nonimportation laws should not preclude that state from receiving money for a hazardous waste program. The criteria for defining hazardous wastes must be realistic if an unmanageable list is to be avoided. State solid waste management agencies must provide aid to local government and private industry. The state-not EPA- is the best level of government to carry out an effective solid waste program. The Federal program should concentrate on resource and energy conservation, research and development, demonstration projects, establishing markets for recycled materials, and education and training programs. Planning should be coordinated through state agencies.

Exiting RCRA Subtitle C regulation data for supporting a new regulatory path for immobilized mixed debris

Energy Technology Data Exchange (ETDEWEB)

Porter, C.L. [Jetseal, Inc., Idaho Falls, ID (United States); Carson, S.D.; Cheng, Wu-Ching [Sandia National Labs., Albuquerque, NM (United States)

1995-12-31

This paper presents analytical and empirical data that provide technical support for the position that mixed debris (debris contaminated with both radioactive and hazardous constituents) treated by immobilization in accordance with 40 CFR 268.45 can exit RCRA Subtitle C requirements at the time the treatment is complete. Pathways analyses and risk assessments of low-level waste and RCRA mixed waste disposal facilities show that these two types of facilities provide equivalent long-term (> 100 years) performance and protection of human health and the environment. A proposed two-tier approach for waste form performance criteria is discussed.

Performance test results of noninvasive characterization of RCRA surrogate waste by prompt gamma neutron activation analysis

International Nuclear Information System (INIS)

Gehrke, R.J.; Propp, W.A.

1997-11-01

A performance evaluation to determine the feasibility of using prompt gamma neutron activation analysis (PGNAA) for noninvasive, quantitative assay of mixed waste containers was sponsored by DOE's Office of Technology Development (OTD), the Mixed Waste Focus Area (MWFA), and the Idaho National Engineering and Environmental Laboratory (INEEL). The evaluation was conducted using a surrogate waste, based on Portland cement, that was spiked with three RCRA metals, mercury, cadmium, and lead. The results indicate that PGNAA has potential as a process monitor. However, further development is required to improve its sensitivity to meet regulatory requirements for determination of these RCRA metals

Results of RCRA groundwater quality assessment at the 216-B-3 Pond Facility

International Nuclear Information System (INIS)

Barnett, D.B.; Teel, S.S.

1997-06-01

This document describes a groundwater quality assessment of the 216-B-3 pond system, a Resources Conservation and Recovery act of 1976 (RCRA) waste facility. In 1990, sampling and chemical analysis of groundwater underlying the facility indicated that the contamination indicator parameters, total organic halogens (TOX), and total organic carbon (TOC) had exceeded established limits in two wells. This discovery placed the facility into RCRA groundwater assessment status and subsequently led to a more detailed hydrochemical analysis of groundwater underlying the facility. Comprehensive chemical analyses of groundwater samples from 1994 through 1996 revealed one compound, tris (2-chloroethyl) phosphate (TRIS2CH), that may have contributed to elevated TOX concentrations. No compound was identified as a contributor to TOC. Detailed evaluations of TOX, TOC, and TRIS2CH and comparison of occurrences of these parameters led to conclusions that (1) with few exceptions, these constituents occur at low concentrations below or near limits of quantitation; (2) it is problematic whether the low concentrations of TRIS2CH represent a contaminant originating from the facility or if it is a product of well construction; and (3) given the low and diminishing concentration of TOX, TOC, and TRIS2CH, no further investigation into the occurrent of these constituents is justified. Continued groundwater monitoring should include an immediate recalculation of background critical means of upgradient/downgradient comparisons and a return to seminannual groundwater monitoring under a RCRA indicator parameter evaluation program

Resource conversation and recovery act (RCRA) Contingency Plan for interim status or permitted units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1992-08-01

The official mission of the Y-12 Plant is to serve as a manufacturing technology center for key processes such that capabilities are maintained for safe, secure, reliable, and survivable nuclear weapons systems and other applications of national importance. The Y-12 RCRA Contingency Plan will be reviewed and revised if necessary if the facility RCRA operating permits are revised, the plan is inadequate in an emergency, the procedures herein can be improved, the facility's operations change in a manner that alters the plan, the emergency coordinator changes, or the emergency equipment list changes. Copies of the Y-12 Emergency Management Plan are available at the Plant Shift Superintendent's Office and the Emergency Preparedness Office. This document serves to supplement the Y-12 Emergency Management Plan to be appropriate for all RCRA hazardous waste interim status or permitted treatment, storage, or disposal facilities. The 90-day storage areas at the Y-12 Plant have a separate contingency supplement as required by RCRA and are separate from this supplement

Groundwater Monitoring Plan for the 1301-N, 1324-N/NA, and 1325-N RCRA Facilities

International Nuclear Information System (INIS)

Hartman, Mary J.

2001-01-01

The 1301-N and 1325-N Liquid Waste Disposal Facilities, the 1324-N Surface Impoundment, and the 1324-NA Percolation Pond, located in the 100 N Area of the Hanford Site, are regulated under the Resource Conservation and Recovery Act of 1976 (RCRA). The closure plans for these facilities stipulate that groundwater is monitored according to the 100-N Pilot Project: Proposed Consolidated Groundwater Monitoring Program (BHI-00725). This document supplements the consolidated plan by providing information on sampling and analysis protocols, quality assurance, data management, and a conceptual model for the RCRA sites. Monitoring well networks, constituents, and sampling frequency remain the same as in the consolidated plan or the previous groundwater monitoring plan (Hartman 1996)

Quarterly report of RCRA groundwater monitoring data for period January 1--March 31, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This quarterly report contains data received between January and March 1995, which are the cutoff dates for this reporting period. This report may contain not only data from the January through March quarter, but also data from earlier sampling events that were not previously reported. Nineteen Resource Conservation and Recovery Act of 1976 (RCRA) groundwater monitoring projects are conducted at the Hanford Site. These projects include treatment, storage, and disposal facilities for both solid and liquid waste. The groundwater monitoring programs described in this report comply with the interim-status federal (Title 40 Code of Federal Regulation [CFR] Part 265) and state (Washington Administrative Code [WAC] 173-303-400) regulations. The RCRA projects are monitored under one of three programs: background monitoring, indicator parameter evaluation, or groundwater quality assessment.

76 FR 76158 - Agency Information Collection Activities; Proposed Collection; Comment Request; RCRA Expanded...

Science.gov (United States)

2011-12-06

... contents of the docket, and to access those documents in the public docket that are available..., including through the use of appropriate automated electronic, mechanical, or other technological collection... as State, local, or Tribal governments. Title: RCRA Expanded Public Participation. ICR numbers: EPA...

Preparation of radioactive ''mixed'' waste samples for measurement of RCRA [Resource Conservation and Recovery Act] organic compounds

International Nuclear Information System (INIS)

Tomkins, B.A.; Caton, J.E.

1987-01-01

A radioactive ''mixed'' waste typically contains alpha-, beta-, or gamma-emitting radionuclides and varying quantities of semivolatile or volatile organic species, some or all of which may be named specifically by the Resource Conservation and Recovery Act (RCRA). Because there are no acceptable means available currently for disposing of these mixed wastes, they are presently stored above-ground in sealed drums. For this reason, analytical procedures which can determine RCRA organics in radioactive waste are necessary for deciding the proper approach for disposal. An important goal of this work is the development of methods for preparing mixed waste samples in a manner which allows the RCRA organics to be measured in conventional organic analysis laboratories without special precautions. Analytical procedures developed for handling mixed waste samples must satisfy not only the usual constraints present in any trace-level organic chemical determination, but also those needed to insure the protection of the operator from radioactive contamination. Consequently, procedures should be designed to use the least amount of radioactive sample commensurate with achieving acceptable sensitivity with the RCRA analytical methods. Furthermore, the unusual laboratory glassware which would normally be used should be replaced with disposable materials wherever possible, in order to reduce the ''clean-up'' time required, and thereby reduce the operator's exposure to radioactivity. Actual sample handling should be reduced to the absolute minimum. Finally, the final isolate must exhibit a sufficiently low level of alpha, beta, or gamma activity to permit detailed characterization in a conventional organic analysis laboratory. 4 refs., 5 tabs

RCRA and CERCLA requirements affecting cleanup activities at a federal facility superfund site

International Nuclear Information System (INIS)

Walsh, T.J.

1994-01-01

The Fernald Environmental Management Project (FEMP) achieved success on an integrated groundwater monitoring program which addressed both RCRA and CERCLA requirements. The integrated plan resulted in a cost savings of approximately $2.6 million. At present, the FEMP is also working on an integrated closure process to address Hazardous Waste Management Units (HWMUs) at the site. To date, Ohio EPA seems willing to discuss an integrated program with some stipulations. If an integrated program is implemented, a cost savings of several million dollars will be realized since the CERCLA documents can be used in place of a RCRA closure plan. The success of an integrated program at the FEMP is impossible without the support of DOE and the regulators. Since DOE is an owner/operator of the facility and Ohio EPA regulates hazardous waste management activities at the FEMP, both parties must be satisfied with the proposed integration activities. Similarly, US EPA retains CERCLA authority over the site along with a signed consent agreement with DOE, which dictates the schedule of the CERCLA activities. Another federal facility used RCRA closure plans to satisfy CERCLA activities. This federal facility was in a different US EPA Region than the FEMP. While this approach was successful for this site, an integrated approach was required at the FEMP because of the signed Consent Agreement and Consent Decree. For federal facilities which have a large number of HWMUs along with OUs, an integrated approach may result in a timely and cost-effective cleanup

RCRA Assessment Plan for Single-Shell Tank Waste Management Area TX-TY

Energy Technology Data Exchange (ETDEWEB)

Horton, Duane G.

2007-03-26

WMA TX-TY contains underground, single-shell tanks that were used to store liquid waste that contained chemicals and radionuclides. Most of the liquid has been removed, and the remaining waste is regulated under the RCRA as modi¬fied in 40 CFR Part 265, Subpart F and Washington State’s Hazardous Waste Management Act . WMA TX-TY was placed in assessment monitoring in 1993 because of elevated specific conductance. A groundwater quality assessment plan was written in 1993 describing the monitoring activities to be used in deciding whether WMA TX-TY had affected groundwater. That plan was updated in 2001 for continued RCRA groundwater quality assessment as required by 40 CFR 265.93 (d)(7). This document further updates the assessment plan for WMA TX-TY by including (1) information obtained from ten new wells installed at the WMA after 1999 and (2) information from routine quarterly groundwater monitoring during the last five years. Also, this plan describes activities for continuing the groundwater assessment at WMA TX TY.

Groundwater monitoring plan for the Hanford Site 216-B-3 pond RCRA facility

International Nuclear Information System (INIS)

Barnett, D.B.; Chou, C.J.

1998-06-01

The 216-B-3 pond system was a series of ponds for disposal of liquid effluent from past Hanford production facilities. In operation since 1945, the B Pond system has been a RCRA facility since 1986, with Resource Conservation and Recovery Act (RCRA) interim-status groundwater monitoring in place since 1988. In 1994, discharges were diverted from the main pond, where the greatest potential for contamination was thought to reside, to the 3C expansion pond. In 1997, all discharges to the pond system were discontinued. In 1990, the B Pond system was elevated from detection groundwater monitoring to an assessment-level status because total organic halogens and total organic carbon were found to exceed critical means in two wells. Subsequent groundwater quality assessment failed to find any specific hazardous waste contaminant that could have accounted for the exceedances, which were largely isolated in occurrence. Thus, it was recommended that the facility be returned to detection-level monitoring

Quarterly report of RCRA groundwater monitoring data for period October 1 through December 31, 1994

International Nuclear Information System (INIS)

1995-04-01

Hanford Site interim-status groundwater monitoring projects are conducted as either background, indicator parameter evaluation, or groundwater quality assessment monitoring programs as defined in the Resource Conservation and Recovery Act of 1976 (RCRA); and open-quotes Interim Status Standards for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilitiesclose quotes (Title 40 Code of Federal Regulations [CFR] Part 265), as amended. Compliance with the 40 CFR 265 regulations is required by the Washington Administrative Code (WAC) 173-303. This report contains data from Hanford Site groundwater monitoring projects. The location of each facility is shown. Westinghouse Hanford Company (WHC) manages the RCRA groundwater monitoring projects for federal facilities on the Hanford Site. Performing project management, preparing groundwater monitoring plans, well network design and installation, specifying groundwater data needs, performing quality control (QC) oversight, data management, and preparing project sampling schedules are all parts of this responsibility. Pacific Northwest Laboratory (PNL) administers the contract for analytical services and provides groundwater sampling services to WHC for the RCRA groundwater monitoring program. This quarterly report contains data received between October and December 1994, which are the cutoff dates for this reporting period. This report may contain not only data from the October through December quarter, but also data from earlier sampling events that were not previously reported

Special Focus Areas for Hazardous Waste Cleanups under the Resource Conservation and Recovery Act (RCRA)

Science.gov (United States)

In order to manage the new and changing needs of the RCRA Corrective Action Program, EPA is constantly exploring program enhancements, alternate exposure pathways, and new technologies available to protect human health and environment.

CY2003 RCRA GROUNDWATER MONITORING WELL SUMMARY REPORT

International Nuclear Information System (INIS)

MARTINEZ, C.R.

2003-01-01

This report describes the calendar year (CY) 2003 field activities associated with the installation of two new groundwater monitoring wells in the A-AX Waste Management Area (WMA) and four groundwater monitoring wells in WMA C in the 200 East Area of the Hanford Nuclear Reservation. All six wells were installed by Fluor Hanford Inc. (FH) for CH2M Hill Hanford Group, Inc. (CHG) in support of Draft Hanford Facility Agreement and Consent Order (Tri-Party Agreement) M-24-00 milestones and ''Resource Conservation and Recovery Act of 1976'' (RCRA) groundwater monitoring requirements. Drilling data for the six wells are summarized in Table 1

Field Sampling Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System - 1997 Notice of Violation Consent Order

International Nuclear Information System (INIS)

Evans, S.K.

2002-01-01

This Field Sampling Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System is one of two documents that comprise the Sampling and Analysis Plan for the HWMA/RCRA closure certification of the TRA-731 caustic and acid storage tank system at the Idaho National Engineering and Environmental Laboratory. This plan, which provides information about sampling design, required analyses, and sample collection and handling procedures, is to be used in conjunction with the Quality Assurance Project Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System

Combination RCRA groundwater monitoring plan for the 216-A-10, 216-A-36B, and 216-A-37-1 PUREX cribs

International Nuclear Information System (INIS)

Lindberg, J.W.

1997-06-01

This document presents a groundwater quality assessment monitoring plan, under Resource Conservation and Recovery Act of 1976 (RCRA) regulatory requirements for three RCRA sites in the Hanford Site's 200 East Area: 216-A-10, 216-A-36B, and 216-A-37-1 cribs (PUREX cribs). The objectives of this monitoring plan are to combine the three facilities into one groundwater quality assessment program and to assess the nature, extent, and rate of contaminant migration from these facilities. A groundwater quality assessment plan is proposed because at least one downgradient well in the existing monitoring well networks has concentrations of groundwater constituents indicating that the facilities have contributed to groundwater contamination. The proposed combined groundwater monitoring well network includes 11 existing near-field wells to monitor contamination in the aquifer in the immediate vicinity of the PUREX cribs. Because groundwater contamination from these cribs is known to have migrated as far away as the 300 Area (more than 25 km from the PUREX cribs), the plan proposes to use results of groundwater analyses from 57 additional wells monitored to meet environmental monitoring requirements of US Department of Energy Order 5400.1 to supplement the near-field data. Assessments of data collected from these wells will help with a future decision of whether additional wells are needed

RCRA permit modifications and the functional equivalency demonstration: A case study

International Nuclear Information System (INIS)

Kinker, J.; Lyon, W.; Carnes, R.; Loehr, C.; Elsberry, K.; Garcia, P.

1996-01-01

Hazardous waste operating permits issued under the Resource Conservation and Recovery Act (RCRA) often impose requirements, typically by reference to the original permit application, that specific components and equipment be used. Consequently, changing these items, even for the purpose of routine maintenance, may first require that the owner/operator request a potentially time-consuming and costly permit modification. However, the owner/operator may demonstrate that a modification is not required because the planned changes are functionally equivalent, as defined by RCRA, to the original specifications embodied by the permit. The Controlled-Air Incinerator at Los Alamos National Laboratory is scheduled for maintenance and improvements that involve replacement of components. The incinerator's carbon adsorption unit/high efficiency particulate air filtration system, in particular, was redesigned to improve reliability and minimize maintenance. A study was performed to determine whether the redesigned unit would qualify as functionally equivalent to the original component. in performing this study, the following steps were taken: (a) the key performance factors were identified; (b) performance data describing the existing unit were obtained; (c) performance of both the existing and redesigned units was simulated; and (d) the performance data were compared to ascertain whether the components could qualify as functionally equivalent

Cleanups In My Community (CIMC) - RCRA and Base Realignment and Closure (BRAC) Federal Facilities, National Layer

Data.gov (United States)

U.S. Environmental Protection Agency — This data layer provides access to Resource Conservation and Recovery Act (RCRA) Base Realignment and Closure (BRAC) sites as part of the CIMC web service. The...

Dewatering and RCRA partial closure action on solar evaporation ponds, Rocky Flats Plant, Golden, Colorado

International Nuclear Information System (INIS)

1991-06-01

The Department of Energy (DOE) has prepared an Environmental Assessment (DOE/EA-0487) on its proposal to partially close five solar evaporation ponds at the Rocky Flats Plant (RFP) pursuant to the requirements of the Resource Conservation and Recovery Act (RCRA). This proposal would be known as a RCRA partial closure and would be accomplished by dewatering the ponds, where necessary, and converting any remaining sludge or evaporator concentrate to a solid wasteform (pondcrete and saltcrete). The pond sites would be stabilized to prevent erosion or other disturbance to the soil and to prevent infiltration of rain or snowmelt. The solid wasteform would be transported offsite for disposal. The five solar ponds (designated 207-A, 207-B (north, center, and south), and 207-C), are the only solar evaporation ponds that exist at the RFP. A finding of no significant impact is included

HANFORD TANK FARM RESOURCE CONSERVATION and RECOVERY ACT (RCRA) CORRECTIVE ACTION PROGRAM

International Nuclear Information System (INIS)

KRISTOFZSKI, J.G.

2007-01-01

As a consequence of producing special nuclear material for the nation's defense, large amounts of extremely hazardous radioactive waste was created at the US Department of Energy's (DOE) Hanford Site in south central Washington State. A little over 50 million gallons of this waste is now stored in 177 large, underground tanks on Hanford's Central Plateau in tank farms regulated under the Atomic Energy Act and the Resource, Conservation, and Recovery Act (RCRA). Over 60 tanks and associated infrastructure have released or are presumed to have released waste in the vadose zone. In 1998, DOE's Office of River Protection established the Hanford Tank Farm RCRA Corrective Action Program (RCAP) to: (1) characterize the distribution and extent of the existing vadose zone contamination; (2) determine how the contamination will move in the future; (3) estimate the impacts of this contamination on groundwater and other media; (4) develop and implement mitigative measures; and (5) develop corrective measures to be implemented as part of the final closure of the tank farm facilities. Since its creation, RCAP has made major advances in each of these areas, which will be discussed in this paper

Resource Conservation and Recovery Act (RCRA) contingency plan for hazardous waste treatment, storage, and disposal units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1994-08-01

The Y-12 RCRA Contingency Plan will be continually reviewed and revised if any of the following occur: the facility permit is revised, the plan is inadequate in an emergency, the procedures can be improved, the operations of the facility change in a way that alters the plan, the emergency coordinator changes, or the emergency equipment list changes. Copies of the Y-12 Emergency Management Plan are available at the Plant Shift Superintendent's Office and the Emergency Management Office. This document serves to supplement the Y-12 Emergency Management Plan to be appropriate for all RCRA hazardous waste treatment, storage, or disposal units. The 90-day accumulation areas at the Y-12 Plant have a separate contingency supplement as required by RCRA and are separate from this supplement

RCRA corrective action ampersand CERCLA remedial action reference guide

International Nuclear Information System (INIS)

1994-07-01

This reference guide provides a side-by-side comparison of RCRA corrective action and CERCLA Remedial Action, focusing on the statutory and regulatory requirements under each program, criterial and other factors that govern a site's progress, and the ways in which authorities or requirements under each program overlap and/or differ. Topics include the following: Intent of regulation; administration; types of sites and/or facilities; definition of site and/or facility; constituents of concern; exclusions; provisions for short-term remedies; triggers for initial site investigation; short term response actions; site investigations; remedial investigations; remedial alternatives; clean up criterial; final remedy; implementing remedy; on-site waste management; completion of remedial process

A review of state regulations that exceed those of the federal Resource Conservation and Recovery Act (RCRA)

International Nuclear Information System (INIS)

Coutant, C.C.; Heckman, C.L.

1988-04-01

This report identifies and provides information on state hazardous waste management programs and regulations in states where the US Department of Energy (DOE) has facilities. The objective is to describe for the DOE defense program and its contractors how state requirements are more stringent than the federal regulations under the Resource Conservation and Recovery Act (RCRA). DOE defense programs are located in 13 of the 50 states. Most of these states have regulations that are essentially equivalent to the federal RCRA requirements as they existed prior to the 1984 amendments, but their regulations are, in most instances, more stringment than the federal requirements. Differences are both substantive and procedural, and they are summarized and tabulated herein. All but three of these 13 states have been granted Final Authorization from the US Environmental Protection Agency (EPA) to operate their own hazardous waste management program in accord with the federal RCRA program prior to the 1984 amendments; two of the three others have some stage of Interim Authorization. EPA currently administers all of the provisions of the 1984 amendments, including requirements for corrective action under Sect. 3004(u). Two states, Colorado and Tennessee, have been granted revisions to their Final Authorizations delegating responsibility for the hazardous wastes. Responsible state agencies (with appropriate telephone numbers) are indicated, as are the relevant laws and current regulatory statutes

Resource Conservation and Recovery Act (RCRA) general contingency plan for hazardous waste treatment, storage, and disposal units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

Skaggs, B.E.

1993-11-01

The Y-12 RCRA Contingency Plan will be continually reviewed and revised if any of the following occur: the facility permit is revised, the plan is inadequate in an emergency, the procedures herein can be improved, the operations of the facility change in a way that alters the plan, the emergency coordinator changes, or the emergency equipment list changes. Copies of the Y-12 Emergency Management Plan are available at the Plant Shift Superintendent's Office and the Emergency Management Office. This document serves to supplement the Y-12 Emergency Management Plan to be appropriate for all RCRA hazardous waste treatment, storage, or disposal units. The 90-day accumulation areas at the Y-12 Plant have a separate contingency supplement as required by RCRA and are separate from this supplement

The ontological turn meets the certainty of death.

Science.gov (United States)

McDonald, Maryon

2017-08-01

The 'ontological turn' involves some anthropological points of long standing but the approaches recently coordinated into this turn have been presented as a 'call to arms', as shaking up 'mono-realist singularities' and as inherently political. This fighting talk has no doubt made important contributions to anthropology and insights from the ontological turn can help in anthropological understandings of medical practices. However, this paper contends that this helpfulness is also limited and that a call to arms may be inappropriate. This point is made through an ethnographic understanding of medical concern about the diagnosis of death.

Quarterly report of RCRA groundwater monitoring data for period April 1, 1993 through June 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Jungers, D.K.

1993-10-01

Hanford Site interim-status groundwater monitoring projects are conducted as either background, indicator parameter evaluation, or groundwater quality assessment monitoring programs. This report contains data from Hanford Site groundwater monitoring projects. Westinghouse Hanford Company (WHC) manages the RCRA groundwater monitoring projects for federal facilities on the Hanford Site. Project management, specifying data needs, performing quality control (QC) oversight, managing data, and preparing project sampling schedules are all parts of this responsibility. Pacific Northwest Laboratory (PNL) administers the contract for analytical services and provides groundwater sampling services to WHC for the RCRA groundwater monitoring program. This quarterly report contains data received between May 24 and August 20, 1993, which are the cutoff dates for this reporting period. This report may contain not only data from samples collected during the April through June quarter but also data from earlier sampling events that were not previously reported.

Where Do Jamaican Adolescents Turn for Psychological Help?

Science.gov (United States)

Williams, Dahra Jackson

2012-01-01

Background: Stigma about mental health is a significant problem in Jamaica and the wider English-speaking Caribbean. In general, negative attitudes and opinions about mental illness have been found to negatively impact psychological help-seeking among several populations. Objective: This study examined Jamaican adolescents' preferential sources of…

ORGDP RCRA/PCB incinerator facility

International Nuclear Information System (INIS)

Rogers, T.

1987-01-01

A dual purpose solid/liquid incinerator is currently being constructed at the Oak Ridge Gaseous Diffusion Plant [ORGDP (K-25)] to destroy uranium contaminated, hazardous organic wastes in compliance with the Toxic Substances Control Act (TSCA) and the Resource Conservation and Recovery Act (RCRA). These wastes are generated by the gaseous diffusion plants in Oak Ridge, TN; Paducah, KY; and Portsmouth, OH. In addition, waste will also be received from the Y-12 Plant, Oak Ridge National Laboratory (ORNL), and the Feed Materials Production Center (FMPC). Destruction of PCBs and hazardous liquid organic wastes will be accomplished in a rotary kiln incinerator with an afterburner. This system was selected faster a study of various alternatives. Incineration was chosen because it is dependable, permanent, detoxifies organics, and reduces volume. The rotary kiln incinerator was selected because it can thermally destroy organic constituents of liquids, solids, and sludges to produce an organically inert ash. In addition to the incineration off-gas treatment system, the facility includes a tank farm, drum storage buildings, a solids preparation area, a control room, and a data management system. The incineration system, off-gas treatment system, and related instrumentation and controls are being provided by International Waste Energy Systems (IWES) which is responsible for design, construction, startup, and performances testing

Quarterly report of RCRA groundwater monitoring data for period April 1 through June 30, 1994

International Nuclear Information System (INIS)

1994-10-01

Hanford Site interim-status groundwater monitoring projects are conducted as either background, indicator parameter evaluation, or groundwater quality assessment monitoring programs as defined in the Resource Conservation and Recovery Act of 1976 (RCRA); and ''Interim Status Standards for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities,'' as amended (40 Code of Federal Regulations [CFR] 265). Compliance with the 40 CFR 265 regulations is required by the Washington Administrative Code (WAC) 173-303. This report contains data from Hanford Site groundwater monitoring projects. Westinghouse Hanford Company manages RCRA groundwater monitoring projects for federal facilities on the Hanford Site. Project management, specifying data needs, performing quality control oversight, managing data, and preparing project sampling schedules are all parts of this responsibility. This quarterly report contains data received between May 20 and August 19, 1994, which are the cutoff dates for this reporting period. This report may contain not only data from the April through June quarter but also data from earlier sampling events that were not previously reported

RCRA facility investigation/corrective measures study work plan for the 100-DR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et. al. 1990a), signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations. Some of the TSD facilities are included in the operable units. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-DR-1 source operable unit Source operable units include facilities and unplanned release sites that are potential sources of contamination

Issues in radioactive mixed waste compliance with RCRA [Resource Conservation and Recovery Act]: Some examples from ongoing operations at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Eaton, D.L.; Smith, T.H.; Clements, T.L. Jr.; Hodge, V.

1990-01-01

Radioactive mixed waste is subject to regulation under both the Resource Conservation and Recovery Act (RCRA) and the Atomic Energy Act (AEA). The regulation of such waste is the responsibility of the Environmental Protection Agency (EPA) and either the Nuclear Regulatory Commission (NRC) or the Department of Energy (DOE), depending on whether the waste is commercially generated or defense-related. The recent application of the RCRA regulations to ongoing operations at the DOE's Idaho National Engineering Laboratory (INEL) are described in greater detail. 8 refs., 2 figs

Quality Assurance Project Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System - 1997 Notice of Violation Consent Order; TOPICAL

International Nuclear Information System (INIS)

Evans, S.K.

2002-01-01

This Quality Assurance Project Plan for the HWMA/RCRA Closure Certification of the TRA- 731 Caustic and Acid Storage Tank System is one of two documents that comprise the Sampling and Analysis Plan for the HWMA/RCRA closure certification of the TRA-731 caustic and acid storage tank system at the Idaho National Engineering and Environmental Laboratory. This plan, which provides information about the project description, project organization, and quality assurance and quality control procedures, is to be used in conjunction with the Field Sampling Plan for the HWMA/RCRA Closure Certification of the TRA-731 Caustic and Acid Storage Tank System. This Quality Assurance Project Plan specifies the procedures for obtaining the data of known quality required by the closure activities for the TRA-731 caustic and acid storage tank system

RCRA and Operational Monitoring (ROM). Multi-Year Program Plan and Fiscal Year 95 Work Plan WBS 1.5.3

Energy Technology Data Exchange (ETDEWEB)

1994-09-17

This document contains information concerning the RCRA and Operational Monitoring Program at Hanford Reservation. Information presented includes: Schedules for ground water monitoring activities, program cost baseline, program technical baseline, and a program milestone list.

Transportable Vitrification System RCRA Closure Practical Waste Disposition Saves Time And Money

International Nuclear Information System (INIS)

Brill, Angie; Boles, Roger; Byars, Woody

2003-01-01

The Transportable Vitrification System (TVS) was a large-scale vitrification system for the treatment of mixed wastes. The wastes contained both hazardous and radioactive materials in the form of sludge, soil, and ash. The TVS was developed to be moved to various United States Department of Energy (DOE) facilities to vitrify mixed waste as needed. The TVS consists of four primary modules: (1) Waste and Additive Materials Processing Module; (2) Melter Module; (3) Emissions Control Module; and (4) Control and Services Module. The TVS was demonstrated at the East Tennessee Technology Park (ETTP) during September and October of 1997. During this period, approximately 16,000 pounds of actual mixed waste was processed, producing over 17,000 pounds of glass. After the demonstration was complete it was determined that it was more expensive to use the TVS unit to treat and dispose of mixed waste than to direct bury this waste in Utah permitted facility. Thus, DOE had to perform a Resource Conservation and Recovery Act (RCRA) closure of the facility and find a reuse for as much of the equipment as possible. This paper will focus on the following items associated with this successful RCRA closure project: TVS site closure design and implementation; characterization activities focused on waste disposition; pollution prevention through reuse; waste minimization efforts to reduce mixed waste to be disposed; and lessons learned that would be integrated in future projects of this magnitude

Resource Conservation and Recovery Act (RCRA) Part B permit application for tank storage units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1994-05-01

In compliance with the Resource Conservation and Recovery Act (RCRA), this report discusses information relating to permit applications for three tank storage units at Y-12. The storage units are: Building 9811-1 RCRA Tank Storage Unit (OD-7); Waste Oil/Solvent Storage Unit (OD-9); and Liquid Organic Solvent Storage Unit (OD-10). Numerous sections discuss the following: Facility description; waste characteristics; process information; groundwater monitoring; procedures to prevent hazards; contingency plan; personnel training; closure plan, post closure plan, and financial requirements; record keeping; other federal laws; organic air emissions; solid waste management units; and certification. Sixteen appendices contain such items as maps, waste analyses and forms, inspection logs, equipment identification, etc

RCRA Facility Investigation/Remedial Investigation Report with Baseline Risk Assessment for the Fire Department Hose Training Facility (904-113G)

Energy Technology Data Exchange (ETDEWEB)

Palmer, E. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1997-04-01

This report documents the Resource Conservation and Recovery Act (RCRA) Facility Investigation/Remedial Investigation/Baseline Risk Assessment (RFI/RI/BRA) for the Fire Department Hose Training Facility (FDTF) (904-113G).

Phase 1 RCRA Facility Investigation and Corrective Measures Study Work Plan for Single Shell Tank Waste Management Areas

International Nuclear Information System (INIS)

ROGERS, P.M.

2000-01-01

This document is the master work plan for the Resource Conservation and Recovery Act of 1976 (RCRA) for single-shell tank (SST) farms at the Hanford Site. Evidence indicates that releases at four of the seven SST waste management areas have impacted

Phase 1 RCRA Facility Investigation and Corrective Measures Study Work Plan for Single Shell Tank Waste Management Areas

Energy Technology Data Exchange (ETDEWEB)

ROGERS, P.M.

2000-06-01

This document is the master work plan for the Resource Conservation and Recovery Act of 1976 (RCRA) for single-shell tank (SST) farms at the Hanford Site. Evidence indicates that releases at four of the seven SST waste management areas have impacted.

Proposed modifications to the RCRA post-closure permit for the Chestnut Ridge Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1997-05-01

This report presents proposed modifications to several conditions of the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Chestnut Ridge Hydrogeologic Regime (CRHR) (permit number TNHW-088, EPA ID No. TN3 89 009 0001). These permit conditions define the requirements for RCRA post-closure detection groundwater monitoring at the Chestnut Ridge Sediment Disposal Basin (CRSDB) and Kerr Hollow Quarry (KHQ), and RCRA post-closure corrective action groundwater monitoring at the Chestnut Ridge Security Pits (CRSPs). Modification of these PCP conditions is requested to: (1) clarify the planned integration of RCRA post-closure corrective action groundwater monitoring at the CRSPs with the monitoring program to be established in the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) record of decision (ROD), (2) revise several of the current technical requirements for groundwater monitoring based on implementation of the RCRA monitoring programs during 1996, (3) replace several of the technical procedures included in the PCP with updated versions recently issued by the Y-12 Plant Groundwater Protection Program (GWPP), and (4) correct inaccurate regulatory citations and references to permit conditions and permit attachments. With these modifications, the Y- 12 Plant will continue to meet the full intent of all regulatory obligations for post-closure care of these facilities. Section 2 provides the technical justification for each proposed permit modification. Section 3.0 contains proposed changes to Section II of the PCP. Modifications to site-specific permit conditions are presented in Section 4.0 (CRSDB), Section 5.0 (CRSPs), and Section 6.0 (KHQ). Sections 7.0 and 8.0 reference updated and revised procedures for groundwater sampling, and monitoring well plugging and abandonment, respectively. Appendix A includes all proposed revisions to the permit attachments

Proposed modifications to the RCRA post-closure permit for the Chestnut Ridge Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

This report presents proposed modifications to several conditions of the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Chestnut Ridge Hydrogeologic Regime (CRHR) (permit number TNHW-088, EPA ID No. TN3 89 009 0001). These permit conditions define the requirements for RCRA post-closure detection groundwater monitoring at the Chestnut Ridge Sediment Disposal Basin (CRSDB) and Kerr Hollow Quarry (KHQ), and RCRA post-closure corrective action groundwater monitoring at the Chestnut Ridge Security Pits (CRSPs). Modification of these PCP conditions is requested to: (1) clarify the planned integration of RCRA post-closure corrective action groundwater monitoring at the CRSPs with the monitoring program to be established in the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) record of decision (ROD), (2) revise several of the current technical requirements for groundwater monitoring based on implementation of the RCRA monitoring programs during 1996, (3) replace several of the technical procedures included in the PCP with updated versions recently issued by the Y-12 Plant Groundwater Protection Program (GWPP), and (4) correct inaccurate regulatory citations and references to permit conditions and permit attachments. With these modifications, the Y- 12 Plant will continue to meet the full intent of all regulatory obligations for post-closure care of these facilities. Section 2 provides the technical justification for each proposed permit modification. Section 3.0 contains proposed changes to Section II of the PCP. Modifications to site-specific permit conditions are presented in Section 4.0 (CRSDB), Section 5.0 (CRSPs), and Section 6.0 (KHQ). Sections 7.0 and 8.0 reference updated and revised procedures for groundwater sampling, and monitoring well plugging and abandonment, respectively. Appendix A includes all proposed revisions to the permit attachments.

RCRA closure plan for the Bear Creek Burial Grounds B Area and Walk- In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-01-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Subsequently, this plan was modified again and approved as Y/TS-395, Revised RCRA Closure Plan for the Bear Creek Burial Grounds (February 29, 1988). Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. The plan was presented to the state of Tennessee on March 8, 1990, and the Department of Energy was requested to review other unique alternatives to close the site. This amended closure plan goes further to include inspection and maintenance criteria along with other details

Addendum to the RCRA Assessment Report for Single-Shell Tank Waste Management Area S-SX at the Hanford Site

International Nuclear Information System (INIS)

Chou, C.J.; Johnson, V.G.

1999-01-01

The initial Resource Conservation and Recovery Act (RCRA) groundwater quality assessment report for Waste Management Area S-SX (PNNL-11810) was issued in January 1998. The report stated a plan for conducting continued assessment would be developed after addressing Washington State Department of Ecology (Ecology) comments on initial findings in PNNL-11810. Comments from Ecology were received by US Department of Energy, Richland Operations Office (DOE-RL) on September 24, 1998. Shortly thereafter, Ecology and DOE began dispute resolution and related negotiations about tank farm vadose issues. This led to proposed new Tri-Party Agreement milestones covering a RCRA Facility Investigation-Corrective Measures Study (RFI/CMS) of the four single-shell tank farm waste management areas that were in assessment status (Waste Management Areas B-BX-BY, S-SX, T and TX-TY). The RCRA Facility Investigation includes both subsurface (vadose zone and groundwater) and surface (waste handling facilities and grounds) characterization. Many of the Ecology comments on PNNL-11810 are more appropriate for, and in many cases are superseded by, the RFI/CMS at Waste Management Area S-SX. The proposed Tri-Party Agreement milestone changes that specify the scope and schedule for the RFI/CMS work plans (Tri-Party Agreement change number M-45-98-0) were issued for public comment in February 1999. The Tri-Party Agreement narrative indicates the ongoing groundwater assessments will be integrated with the RFI/CMS work plans. This addendum documents the disposition of the Ecology comments on PNNL-11810 and identifies which comments were more appropriate for the RFI/CMS work plan

Addendum to the RCRA Assessment Report for Single-Shell Tank Waste Management Area S-SX at the Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Chou, C.J.; Johnson, V.G.

1999-10-07

The initial Resource Conservation and Recovery Act (RCRA) groundwater quality assessment report for Waste Management Area S-SX (PNNL-11810) was issued in January 1998. The report stated a plan for conducting continued assessment would be developed after addressing Washington State Department of Ecology (Ecology) comments on initial findings in PNNL-11810. Comments from Ecology were received by US Department of Energy, Richland Operations Office (DOE-RL) on September 24, 1998. Shortly thereafter, Ecology and DOE began dispute resolution and related negotiations about tank farm vadose issues. This led to proposed new Tri-Party Agreement milestones covering a RCRA Facility Investigation-Corrective Measures Study (RFI/CMS) of the four single-shell tank farm waste management areas that were in assessment status (Waste Management Areas B-BX-BY, S-SX, T and TX-TY). The RCRA Facility Investigation includes both subsurface (vadose zone and groundwater) and surface (waste handling facilities and grounds) characterization. Many of the Ecology comments on PNNL-11810 are more appropriate for, and in many cases are superseded by, the RFI/CMS at Waste Management Area S-SX. The proposed Tri-Party Agreement milestone changes that specify the scope and schedule for the RFI/CMS work plans (Tri-Party Agreement change number M-45-98-0) were issued for public comment in February 1999. The Tri-Party Agreement narrative indicates the ongoing groundwater assessments will be integrated with the RFI/CMS work plans. This addendum documents the disposition of the Ecology comments on PNNL-11810 and identifies which comments were more appropriate for the RFI/CMS work plan.

Performance Demonstration Program Plan for RCRA Constituent Analysis of Solidified Wastes

International Nuclear Information System (INIS)

2006-01-01

The Performance Demonstration Program (PDP) for Resource Conservation and Recovery Act (RCRA) constituents distributes test samples for analysis of volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), and metals in solid matrices. Each distribution of test samples is termed a PDP cycle. These evaluation cycles provide an objective measure of the reliability of measurements performed for transuranic (TRU) waste characterization. The primary documents governing the conduct of the PDP are the Quality Assurance Program Document (QAPD; DOE/CBFO-94-1012) and the Waste Isolation Pilot Plant (WIPP) Waste Analysis Plan (WAP) contained in the Hazardous Waste Facility Permit (NM4890139088-TSDF) issued by the New Mexico Environment Department. The WAP requires participation in the PDP; the PDP must comply with the QAPD and the WAP. This plan implements the general requirements of the QAPD and the applicable requirements of the WAP for the RCRA PDP. Participating laboratories demonstrate acceptable performance by successfully analyzing single-blind performance evaluation samples (subsequently referred to as PDP samples) according to the criteria established in this plan. PDP samples are used as an independent means to assess laboratory performance regarding compliance with the WAP quality assurance objectives (QAOs). The concentrations of analytes in the PDP samples address levels of regulatory concern and encompass the range of concentrations anticipated in waste characterization samples. The WIPP requires analyses of homogeneous solid wastes to demonstrate compliance with regulatory requirements. These analyses must be performed by laboratories that demonstrate acceptable performance in this PDP. These analyses are referred to as WIPP analyses, and the samples on which they are performed are referred to as WIPP samples. Participating laboratories must analyze PDP samples using the same procedures used for WIPP samples.

The Pinellas Plant RCRA facility investigation - A case study

International Nuclear Information System (INIS)

Kilbury, Richard; Keshian, Berg; Farley, Dwain; Meyer, David; Ingle, David; Biedermann, Charles

1992-01-01

Under the direction of the U.S. Department of Energy Albuquerque Field Office Environmental Restoration Program, a Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) was completed at the Pinellas Plant to fulfill requirements of the Hazardous and Solid Waste Amendments of 1984 (HSWA) permit issued on February 9, 1990 by the U.S. Environmental Protection Agency (EPA). This RFI addressed potential contaminant releases and environmental conditions at 15 solid waste management units (SWMUs). The RFI characterization program began in April 1990 and was completed in May 1991. The scope of RFI data collection activities is presented in the Pinellas Plant RFI Workplan issued in May 1990 and approved by EPA on April 16, 1991. An RFI Report was submitted to EPA on September 1, 1991. This paper presents a summary of RFI results and conclusions. Primary environmental concerns at the Pinellas Plant are emphasized. (author)

Proposed modifications to the RCRA post-closure permit for the Bear Creek Hydrogeologic Regime at the US Department of Energy Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1997-05-01

This report presents proposed modifications to several conditions of the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Bear Creek Hydrogeologic Regime (BCHR). These permit conditions define the requirements for RCRA post-closure corrective action groundwater monitoring at the S-3 Ponds, the Oil Landfarm, and the Bear Creek Burial Grounds (units A, C-West, and Walk-in Pits). Modification of these PCP conditions is requested to: (1) clarify the planned integration of RCRA post-closure corrective action groundwater monitoring with the monitoring program to be established in the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Record of Decision (ROD) for the Bear Creek Valley (BCV) Watershed, (2) revise several of the current technical requirements for groundwater monitoring based on implementation of the RCRA post-closure corrective action monitoring program during 1996, and (3) update applicable technical procedures with revised versions recently issued by the Y-12 Plant Groundwater Protection Program (GWPP). With these modifications, the Y-12 Plant will continue to meet the full intent of all regulatory obligations for post-closure care of these facilities. Section 2.0 provides the technical justification for each proposed permit modification. The proposed changes to permit language are provided in Section 3.0 (S-3 Ponds), Section 4.0 (Oil Landfarm), and Section 5.0 (Bear Creek Burial Grounds). Sections 6.0 and 7.0 reference updated and revised procedures for groundwater sampling, and monitoring well plugging and abandonment, respectively. Appendix A includes all proposed revisions to the PCP Attachments

Proposed modifications to the RCRA post-closure permit for the Bear Creek Hydrogeologic Regime at the US Department of Energy Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

This report presents proposed modifications to several conditions of the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Bear Creek Hydrogeologic Regime (BCHR). These permit conditions define the requirements for RCRA post-closure corrective action groundwater monitoring at the S-3 Ponds, the Oil Landfarm, and the Bear Creek Burial Grounds (units A, C-West, and Walk-in Pits). Modification of these PCP conditions is requested to: (1) clarify the planned integration of RCRA post-closure corrective action groundwater monitoring with the monitoring program to be established in the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Record of Decision (ROD) for the Bear Creek Valley (BCV) Watershed, (2) revise several of the current technical requirements for groundwater monitoring based on implementation of the RCRA post-closure corrective action monitoring program during 1996, and (3) update applicable technical procedures with revised versions recently issued by the Y-12 Plant Groundwater Protection Program (GWPP). With these modifications, the Y-12 Plant will continue to meet the full intent of all regulatory obligations for post-closure care of these facilities. Section 2.0 provides the technical justification for each proposed permit modification. The proposed changes to permit language are provided in Section 3.0 (S-3 Ponds), Section 4.0 (Oil Landfarm), and Section 5.0 (Bear Creek Burial Grounds). Sections 6.0 and 7.0 reference updated and revised procedures for groundwater sampling, and monitoring well plugging and abandonment, respectively. Appendix A includes all proposed revisions to the PCP Attachments.

RCRA facility investigation report for the 200-PO-1 operable unit. Revision 1

International Nuclear Information System (INIS)

1997-05-01

This Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) report is prepared in support of the RFI/corrective measures study process for the 200-PO-1 Groundwater Operable Unit in the 200 East Area of the Hanford Site. This report summarizes existing information on this operable unit presented in the 200 East and PUREX Aggregate Area Management Study Reports, contaminant specific studies, available modeling data, and groundwater monitoring data summary reports. Existing contaminant data are screened against current regulatory limits to determine contaminants of potential concern (COPC). Each identified COPC is evaluated using well-specific and plume trend analyses

Calendar Year 2007 Resource Conservation and Recovery Act Annual Monitoring Report for the U.S. Department of Energy Y-12 National Security Complex, Oak Ridge, Tennessee - RCRA Post-Closure Permit Nos. TNHW-113, TNHW-116, and TNHW-128

Energy Technology Data Exchange (ETDEWEB)

Elvado Environmental

2008-02-01

This report contains groundwater quality monitoring data obtained during calendar year (CY) 2007 at the following hazardous waste treatment, storage, and disposal (TSD) units located at the US Department of Energy (DOE) Y-12 National Security Complex (hereafter referenced as Y-12) in Oak Ridge, Tennessee; this S-3 Site, Oil Landfarm, Bear Creek Burial Grounds/Walk-In Pits (BCBG/WIP), Eastern S-3 Site Plume, Chestnut Ridge Security Pits (CRSP), Chestnut Ridge Sediment Disposal Baste (CRSDB), few Hollow Quarry (KHQ), and East Chestnut Ridge Waste Pile (ECRWP). Hit monitoring data were obtained in accordance with the applicable Resource Conservation and Recovery Act of 1976 (RCRA) hazardous waste post-closure permit (PCP). The Tennessee Department of Environment and Conservation (TDEC) - Division of Solid Waste Management issued the PCPs to define the requirements for RCRA post-closure inspection, maintenance, and groundwater monitoring at the specified TSD units located within the Bear Creek Hydrogeologic Regime (PCP no. TNHW-116), Upper East Fork Poplar Creek Hydrogeologic Regime (PCP no. TNHW-113), and Chestnut Ridge Hydrogeologic Regime (PCP no. TNHW-128). Each PCP requires the Submittal of an annual RCRA groundwater monitoring report containing the groundwater sampling information and analytical results obtained at each applicable TSD unit during the preceding CY, along with an evaluation of groundwater low rates and directions and the analytical results for specified RCRA groundwater target compounds; this report is the RCRA annual groundwater monitoring report for CY 2007. The RCRA post-closure groundwater monitoring requirements specified in the above-referenced PCP for the Chestnut Ridge Regime replace those defined in the previous PCP (permit no. TNHW-088), which expired on September 18, 2005, but remained effective until the TDEC issued the new PCP in September 2006. The new PCP defines site-specific groundwater sampling and analysis requirements for the

An analysis of the CERCLA response program and the RCRA corrective action program in determining cleanup strategies for federal facilities which have been proposed for listing on the National Priorities List

International Nuclear Information System (INIS)

Baker, P.; Vinson, R.

1994-01-01

This document was prepared as an issue paper for the Department of Energy to serve in the decision-making process for environmental restoration activities. The paper compares cleanup requirements under the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and those currently proposed under Subpart S of the Resource Conservation and Recovery Act (RCRA). The history and regulatory framework for both laws is discussed, and the process for environmental restoration actions under both regulatory programs is compared and contrasted. Contaminants regulated under CERCLA and RCRA differ significantly in that radioactive contaminants are subject to Environmental Protection Agency jurisdiction only under CERCLA. The DOE has the jurisdiction to implement radioactive waste management and cleanup levels under the Atomic Energy Act (AEA) at nuclear weapons facilities. For sites with significant amounts of contaminants which are radioactive only, cleanup under RCRA can present significant advantages, since the DOE can then manage restoration activities under its own authority. There are, conversely several significant advantages for a remedial action being conducted at a CERCLA site recognized on the National Priorities List (NPL). Other provisions in the CERCLA remediation and the RCRA corrective action process offer both advantages and disadvantages related to DOE environmental restoration programs. This paper presents a discussion of significant issues which should be considered in such negotiations

Business Intelligence: Turning Knowledge into Power

Science.gov (United States)

Endsley, Krista

2009-01-01

Today, many school districts are turning to business intelligence tools to retrieve, organize, and share knowledge for faster analysis and more effective, guided decision making. Business intelligence (BI) tools are the technologies and applications that gather and report information to help an organization's leaders make better decisions. BI…

RCRA facility investigation/corrective measures study work plan for the 100-HR-3 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order, signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. Also included in the Tri-Party Agreement are 55 Resource Conservation and Recovery Act (RCRA) treatment, storage, or disposal (TSD) facilities that will be closed or permitted to operate in accordance with RCRA regulations, under the authority of Chapter 173-303 Washington Administrative Code (WAC). Some of the TSD facilities are included in the operable units. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-HR-3 operable unit. The 100-HR-3 operable unit underlies the D/DR and H Areas, the 600 Area between them, and the six source operable units these areas contain. The 100-HR-3 operable unit includes all contamination found in the aquifer soils and water within its boundary. Source operable units include facilities and unplanned release sites that are potential sources of contamination. Separate work plans have been initiated for the 100-DR-1 (DOE-RL 1992a) and 100-HR-1 (DOE-RL 1992b) source operable units

Characterization of Vadose Zone Sediment: Uncontaminated RCRA Borehole Core Samples and Composite Samples

International Nuclear Information System (INIS)

Serne, R. Jeffrey; Bjornstad, Bruce N.; Schaef, Herbert T.; Williams, Bruce A.; Lanigan, David C.; Horton, Duane G.; Clayton, Ray E.; Mitroshkov, Alexandre V.; Legore, Virginia L.; O'Hara, Matthew J.; Brown, Christopher F.; Parker, Kent E.; Kutnyakov, Igor V.; Serne, Jennifer N.; Last, George V.; Smith, Steven C.; Lindenmeier, Clark W.; Zachara, John M.; Burke, Deborah Sd.

2001-01-01

The overall goal of the of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities. To meet this goal, CH2M HILL Hanford Group, Inc. asked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediment from within the S-SX Waste Management Area. This report is the first in a series of four reports to present the results of these analyses. Specifically, this report contains all the geologic, geochemical, and selected physical characterization data collected on vadose zone sediment recovered from RCRA borehole bore samples and composite samples. Intact cores from two RCRA boreholes (299-W22-48 and 299-W22-50) near the SX Tank Farm and four, large-quantity grab samples from outcrop sediment on and off the Hanford Site were sampled to better understand the fate of contaminants in the vadose zone beneath underground storage tanks at the Hanford Site. Borehole and outcrop samples analyzed for this report are located outside the tank farms, and therefore may be considered standard or background samples from which to compare contaminated sediments within the tank farms themselves. This report presents our interpretation of the physical, chemical, and mineralogical properties of the uncontaminated vadose zone sediments, and variations in the vertical distribution of these properties. The information presented in this report is intended to support preparation of the S-SX Field Investigation Report to be prepared by CH2M Hill Hanford Group, Inc. as well as future remediation actions at the S-SX Tank Farm

Hazardous Waste Dashboard Help | ECHO | US EPA

Science.gov (United States)

The dashboards found on the Enforcement and Compliance History Online (ECHO) website are specialized to track both facility and agency performance as they relate to compliance with and enforcement of environmental standards under the Resource Conservation and Recovery Act (RCRA).

Temporal trend analysis of RCRA groundwater monitoring data

International Nuclear Information System (INIS)

Need, E.A.

1994-01-01

Statistical analysis of RCRA groundwater monitoring data at a uranium hexafluoride processing facility showed a statistically significant increase in the concentration of gross beta activity in monitor wells downgradient of surface impounds storing calcium fluoride sludge and high pH water. Because evidence of leakage had not been detected in lysimeters installed beneath the impounds, the operator sought an evaluation of other potential causes of the result, including natural variability. This study determined that all five data sets showed either long-term excursionary (spike-like), or seasonal forms of temporal variation. Gross beta had an upward long-term trend with multiple excursions that almost appeared to be seasonal. Gross alpha had an upward long-term trend with multiple excursions that were clearly not seasonal. Specific conductance had both upward and downward long-term trends but no other variations. pH had a downward long-term trend with multiple excursions that were clearly not seasonal. Fluoride had a downward long-term trend without excursions but with clear seasonal variations. The gross beta result that appeared to be a significant change was a spike event on the upward long-term trend

RCRA Facility investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1991-09-01

This report provides a detailed summary of the activities carried out to sample groundwater at Waste Area Grouping (WAG) 6. The analytical results for samples collected during Phase 1, Activity 2 of the WAG 6 Resource Conservation and Recovery Act Facility Investigation (RFI) are also presented. In addition, analytical results for Phase 1, activity sampling events for which data were not previously reported are included in this TM. A summary of the groundwater sampling activities of WAG 6, to date, are given in the Introduction. The Methodology section describes the sampling procedures and analytical parameters. Six attachments are included. Attachments 1 and 2 provide analytical results for selected RFI groundwater samples and ORNL sampling event. Attachment 3 provides a summary of the contaminants detected in each well sampled for all sampling events conducted at WAG 6. Bechtel National Inc. (BNI)/IT Corporation Contract Laboratory (IT) RFI analytical methods and detection limits are given in Attachment 4. Attachment 5 provides the Oak Ridge National Laboratory (ORNL)/Analytical Chemistry Division (ACD) analytical methods and detection limits and Resource Conservation and Recovery Act (RCRA) quarterly compliance monitoring (1988--1989). Attachment 6 provides ORNL/ACD groundwater analytical methods and detection limits (for the 1990 RCRA semi-annual compliance monitoring)

Borehole Data Package for Calendar Year 2000-2001 RCRA Wells at Single-Shell Tank Waste Management Area T

International Nuclear Information System (INIS)

Horton, Duane G; Hodges, Floyd N

2001-01-01

This document compiles information of the drilling and construction, well development, pump installation, and sediment and groundwater sampling applicable to the installation of five new RCRA wells in calendar year 2000 - 2001. Appendix A contains the Well Summary Sheets (as-built diagrams); the Well Construction Summary Reports, and the geologist's logs; Appendix B contains physical properties data; and Appendix C contains the borehole geophysical logs

RCRA [Resource Conservation and Recovery Act] ground-water monitoring projects for Hanford facilities: Annual progress report for 1988

International Nuclear Information System (INIS)

Fruland, R.M.; Lundgren, R.E.

1989-04-01

This report describes the progress during 1988 of 14 Hanford Site ground-water monitoring projects covering 16 hazardous waste facilities and 1 nonhazardous waste facility (the Solid Waste Landfill). Each of the projects is being conducted according to federal regulations based on the Resource Conservation and Recovery Act (RCRA) of 1976 and the State of Washington Administrative Code. 21 refs., 23 figs., 8 tabs

First annual report RCRA post-closure monitoring and inspections for the U-3fi waste unit. Final report, July 1995--October 1996

International Nuclear Information System (INIS)

Emer, D.F.

1997-01-01

This annual Neutron Soil Moisture Monitoring report provides an analysis and summary for site inspections, meteorological information, and neutron soil moisture monitoring data obtained at the U-3fi RCRA Unit, located in Area 3 of the Nevada Site (NTS), Nye County, Nevada during the July 1995 to October 1996 period. Inspections of the U-3fi RCRA Unit are conducted to determine and document the physical condition of the covers, facilities, and any unusual conditions that could impact the proper operation of the waste unit closure. The objective of the neutron logging is to monitor the soil moisture conditions along the 420 ft ER3-3 borehole and detect changes that may be indicative of moisture movement in the regulated interval. This is the first annual report on the U-3fi closure and includes the first year baseline monitoring data as well as one quarter of compliance monitoring data

Body shape helps legged robots climb and turn in complex 3-D terrains

Science.gov (United States)

Han, Yuanfeng; Wang, Zheliang; Li, Chen

Analogous to streamlined shapes that reduce drag in fluids, insects' ellipsoid-like rounded body shapes were recently discovered to be ``terradynamically streamlined'' and enhance locomotion in cluttered terrain by facilitating body rolling. Here, we hypothesize that there exist more terradynamic shapes that facilitate other modes of locomotion like climbing and turning in complex 3-D terrains by facilitating body pitching and yawing. To test our hypothesis, we modified the body shape of a legged robot by adding an elliptical and a rectangular shell and tested how it negotiated with circular and square vertical pillars. With a rectangular shell the robot always pitched against square pillars in an attempt to climb, whereas with an elliptical shell it always yawed and turned away from circular pillars given a small initial lateral displacement. Square / circular pillars facilitated pitching / yawing, respectively. To begin to reveal the contact physics, we developed a locomotion energy landscape model. Our model revealed that potential energy barriers to transition from pitching to yawing are high for angular locomotor and obstacle shapes (rectangular / square) but vanish for rounded shapes (elliptical / circular). Our study supports the plausibility of locomotion energy landscapes for understanding the rich locomotor transitions in complex 3-D terrains.

INEL RCRA [Resource Conservation and Recovery Act] permit for incineration of hazardous waste: Status report

International Nuclear Information System (INIS)

McFee, J.N.; Dalton, J.D.; Bohrer, H.A.

1987-01-01

The Waste Experimental Reduction Facility (WERF) was constructed to reduce the volume of low-level radioactive waste at the Idaho National Engineering Laboratory (INEL). To address the problem of radioactively contaminated ignitable hazardous waste resulting from INEL activities, a development program was carried out to evaluate WERF's ability to meet the regulated criteria for incinerating liquid and solid ignitable waste. Concurrently, INEL submitted its hazardous waste Part B application under the Resource Conservation and Recovery Act (RCRA). As required, and as a major step in the permitting process, the WERF incinerator portion of the permit application included a proposed trial burn, which is a demonstration test of the incinerator's ability to destroy hazardous materials. The trial burn plan was designed to demonstrate the system performance for liquid and solid ignitable wastes at three operating conditions, using a prepared mix of materials representative of waste to be processed. EPA Region X reviewed and commented on the plan prior to the trial burn. Results of the liquid feed trial burn showed a greater than 97% probability of meeting the RCRA-dictated DRE value for chlorinated solvents and a greater than 99% probability for nonchlorinated solvents. Nonchlorinated solid waste results were calculated at a 93% probability of meeting the required DRE, with a 75% probability for chlorinated solid wastes. In addition, the incinerator DRE continued to improve long after the assumed pre-test equilibrium period had ended. The trial burn demonstrates that the WERF incinerator can safely and adequately destroy ignitable hazardous and mixed waste and provides a significant enhancement of the INEL's waste management system

Feasibility study of X-ray K-edge analysis of RCRA heavy metal contamination of sludge packaged in drums

International Nuclear Information System (INIS)

Jensen, T.

1999-01-01

A study has been completed to assess the capabilities of X-ray K-edge analysis in the measurement of RCRA metal contamination of sludge packaged in drums. Results were obtained for mercury and lead contamination. It was not possible to measure cadmium contamination using this technique. No false positive signals were observed. In cases where uniformity of the sludge can be assumed, this analysis can provide a quick, accurate measurement of heavy-metal contamination

Helping Young Children in Frightening Times.

Science.gov (United States)

Young Children, 2001

2001-01-01

Presents ways parents and other adults can help young children deal with tragedy and violence in the wake of terrorist attacks on the United States. Suggests giving reassurance and physical comfort, providing structure and stability, expecting a range of reactions, helping children to talk if they are ready, turning off the television, and…

Construction of mixed waste storage RCRA facilities, Buildings 7668 and 7669: Environmental assessment

International Nuclear Information System (INIS)

1994-04-01

The Department of Energy has prepared an environmental assessment, DOE/EA-0820, to assess the potential environmental impacts of constructing and operating two mixed waste Resource Conservation and Recovery Act (RCRA) storage facilities. The new facilities would be located inside and immediately west of the security-fenced area of the Oak Ridge National Laboratory Hazardous Waste Management Area in Melton Valley, Tennessee. Based on the analyses in the environmental assessment, the Department has determined that the proposed action does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969. Therefore, the preparation of an environmental impact statement is not required, and the Department is issuing this finding of no significant impact

Sulfur polymer cement encapsulation of RCRA toxic metals and metal oxides

International Nuclear Information System (INIS)

Calhoun, C.L. Jr.; Nulf, L.E.; Gorin, A.H.

1995-06-01

A study was conducted to determine the suitability of Sulfur Polymer Cement (SPC) encapsulation technology for the stabilization of RCRA toxic metal and metal oxide wastes. In a series of bench-scale experiments, the effects of sodium sulfide additions to the waste mixture, residence time, and temperature profile were evaluated. In addition, an effort was made to ascertain the degree to which SPC affords chemical stabilization as opposed to physical encapsulation. Experimental results have demonstrated that at the 25 wt % loading level, SPC can effectively immobilize Cr, Cr 2 O 3 , Hg, Pb, and Se to levels below regulatory limits. SPC encapsulation also has been shown to significantly reduce the leachability of other toxic compounds including PbO, PbO 2 , As 2 O 3 , BaO, and CdO. In addition, data has confirmed sulfide conversion of Hg, Pb, PbO, PbO 2 , and BaO as the product of their reaction with SPC

Savannah River Site RCRA Facility Investigation plan: Road A Chemical Basin

International Nuclear Information System (INIS)

1989-06-01

The nature of wastes disposed of at the Road A Chemical Basin (RACB) is such that some degree of soil contamination is probable. Lead has also been detected in site monitoring wells at concentrations above SRS background levels. A RCRA Facility Investigation (RFI) is proposed for the RACB and will include a ground penetrating radar (GPR) survey, collection and chemical and radiological analyses of soil cores, installation of groundwater monitoring wells, collection and chemical and radiological analyses of groundwater samples, and collection of chemical and radiological analyses of surface water and sediment samples. Upon completion of the proposed RFI field work and chemical and radiological analyses, and RFI report should be prepared to present conclusions on the nature and extent of contamination at the site, and to make recommendations for site remediation. If contamination is detected at concentrations above SRS background levels, a receptor analysis should be done to evaluate potential impacts of site contamination on nearby populations

RCRA facility investigation for the townsite of Los Alamos, New Mexico

International Nuclear Information System (INIS)

Dorries, A.M.; Conrad, R.C.; Nonno, L.M.

1992-01-01

During World War II, Los Alamos, New Mexico was established as an ideal location for the secrecy and safety needed for the research and development required to design a nuclear fission bomb. Experiments carried out in the 1940s generated both radioactive and hazardous waste constituents on what is presently part of the Los Alamos townsite. Under the RCRA permit issued to Los alamos national Laboratory in 1990, the Laboratory is scheduled for investigation of its solid waste management units (SWMUs). The existing information on levels of radioactivity on the townsite is principally data from soil samples taken during the last site decontamination in 1976, little information on the presence of hazardous constituents exists today. This paper addresses pathway analysis and a preliminary risk assessment for current residents of the Los Alamos townsite. The estimated dose levels, in mrem per year, show that the previously decontaminated SWMU areas on the Los Alamos townsite will not contribute a radiation dose of any concern to the current residents

The Relational Antecedents of Interpersonal Helping

DEFF Research Database (Denmark)

Stea, Diego; Pedersen, Torben; Foss, Nicolai Juul

2017-01-01

networks are also associated with cognitive costs, which may reduce the focal employee's ability to both recognize the need for help and engage in helping behaviours. For these reasons, the authors assert an inverted U-shaped relation between the size of an ego's social network and engagement in helping...... behaviour. However, high-quality relationships imply higher mutual understanding between the actors, and hence lower cognitive costs. In turn, the position (and threshold) of the curve between network size and interpersonal helping should be influenced by the quality of the relationship between the provider...

Turn by Turn Measurements at the KEK-ATF

CERN Document Server

Renier, Y; Tomas, R; Wendt, M; Eddy, N; Kubo, K; Kuroda, S; Naito, T; Okugi, T; Terunuma, N; Urakawa, J

2013-01-01

The ATF damping ring has been upgraded with new read-out electronics for the beam position monitors (BPM), capable to acquire the beam orbits on a turn-by-turn basis, as well as in a high resolution averaging mode. The new BPM system allows to improve optic corrections and to achieve an even smaller vertical emittance (<2pm). Experimental results are presented based on turn-by-turn beam orbit measurements in the ring, for estimating the β functions and dispersion along the lattice. A fast method to measure spectral line amplitude in a few turns is also presented, including the evaluation of chromaticity.

Turning points in the history of mathematics

CERN Document Server

Grant, Hardy

2015-01-01

This book explores some of the major turning points in the history of mathematics, ranging from ancient Greece to the present, demonstrating the drama that has often been a part of its evolution. Studying these breakthroughs, transitions, and revolutions, their stumbling-blocks and their triumphs, can help illuminate the importance of the history of mathematics for its teaching, learning, and appreciation. Some of the turning points considered are the rise of the axiomatic method (most famously in Euclid), and the subsequent major changes in it (for example, by David Hilbert); the “wedding,” via analytic geometry, of algebra and geometry; the “taming” of the infinitely small and the infinitely large; the passages from algebra to algebras, from geometry to geometries, and from arithmetic to arithmetics; and the revolutions in the late nineteenth and early twentieth centuries that resulted from Georg Cantor’s creation of transfinite set theory. The origin of each turning point is discussed, along with...

Molten salt oxidation of mixed wastes: Separation of radioactive materials and Resource Conservation and Recovery Act (RCRA) materials

International Nuclear Information System (INIS)

Bell, J.T.; Haas, P.A.; Rudolph, J.C.

1995-01-01

The Oak Ridge National Laboratory (ORNL) is participating in a program to apply a molten salt oxidation (MSO) process to treatment of mixed (radioactive and RCRA) wastes. The salt residues from the MSO treatment will require further separations or other processing to prepare them for final disposal. A bench-scale MSO apparatus is being installed at ORNL and will be operated on real Oak Ridge wastes. The treatment concepts to be tested and demonstrated on the salt residues from real wastes are described

Help Stop the Flu | NIH MedlinePlus the Magazine

Science.gov (United States)

... page please turn Javascript on. Feature: Flu Shot Help Stop the Flu Past Issues / Winter 2011 Table ... CDC recommends that Americans do the following to help stop the flu: Cover nose and mouth with ...

RCRA closure of eight land-based units at the Y-12 plant

International Nuclear Information System (INIS)

Stone, J.E.; Welch, S.H.

1988-01-01

Eight land-based hazardous waste management units at the Oak Ridge Y-12 Plant are being closed under an integrated multi-year program. Closure plans for the units have been submitted and are in various stages of revision and regulatory review. These units will be closed by various combinations of methods, including liquid removal and treatment, sludge stabilization, contaminated sludge and/or soil removal, and capping. The closure of these sites will be funded by a new Department of Energy budget category, the Environmental Restoration Budget Category (ERBC), which is intended to provide greater flexibility in the response to closure and remedial activities. A major project, Closure and Post-Closure Activities (CAPCA), has been identified for ERBC funding to close and remediate the land units in accordance with RCRA requirements. Establishing the scope of this program has required the development of risk assessments and the preparation of an integrated schedule

Pilot study: Assessing the effect of continual position monitoring technology on compliance with patient turning protocols

OpenAIRE

Schutt, Suann Cirigliano; Tarver, Christine; Pezzani, Michelle

2017-01-01

Abstract Aim The study aim was to evaluate if continual patient position monitoring, taking into account self‐turns and clinician‐assisted turns, would increase the percentage of time a patient's position changed at least every 2 hr. Background While patient turning has clinical benefits, current models to help staff remember to turn patients, such as “turn clocks” and timers, have not resulted in high compliance with turning protocols. In addition, reminders are based on arbitrary 2‐hr windo...

Custom Search Help | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

Watershed Statistics Help | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

RCRA corrective measures using a permeable reactive iron wall US Coast Guard Support Center, Elizabeth City, North Carolina

International Nuclear Information System (INIS)

Schmithors, W.L.; Vardy, J.A.

1997-01-01

A chromic acid release was discovered at a former electroplating shop at the U.S. Coast Guard Support Center in Elizabeth City, North Carolina. Initial investigative activities indicated that chromic acid had migrated into the subsurface soils and groundwater. In addition, trichloroethylene (TCE) was also discovered in groundwater during subsequent investigations of the hexavalent chromium (Cr VI) plume. Corrective measures were required under the Resource Conservation and Recovery Act (RCRA). The in-situ remediation method, proposed under RCRA Interim Measures to passively treat the groundwater contaminants, uses reactive zero-valent iron to reductively dechlorinate the chlorinated compounds and to mineralize the hexavalent chromium. A 47 meter by 0.6 meter subsurface permeable iron wall was installed downgradient of the source area to a depth of 7 meters using a direct trenching machine. The iron filings were placed in the ground as the soils were excavated from the subsurface. This is the first time that direct trenching was used to install reactive zero-valent iron filings. Over 250 metric tons of iron filings were used as the reactive material in the barrier wall. Installation of the iron filings took one full day. Extensive negotiations with regulatory agencies were required to use this technology under the current facility Hazardous Waste Management Permit. All waste soils generated during the excavation activities were contained and treated on site. Once contaminant concentrations were reduced the waste soils were used as fill material

The marriage of RCRA and CERCLA at the Rocky Flats Environmental Technology Site

International Nuclear Information System (INIS)

Shelton, D.C.; Brooks, L.M.

1998-01-01

A key goal of the Rocky Flats Cleanup Agreement (RFCA) signed in July of 1996 was to provide a seamless marriage of the Resource Conservation and Recovery Act (RCRA) (and other media specific programs) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and the implementing agencies of each. This paper examines the two years since the signing of RFCA and identifies the successes, failures, and stresses of the marriage. RFCA has provided an excellent vehicle for regulatory and substantive progress at the Department of Energy's Rocky Flats facility. The key for a fully successful marriage is to build on the accomplishments to date and to continually improve the internal and external systems and relationships. To date, the parties can be proud of both the substantial accomplishment of substantive environmental work and the regulatory systems that have enabled the work

Superfund TIO videos. Set A. Regulatory overview - CERCLA's relationship to other programs: RCRA, Title III, UST, CWA, SDWA. Part 1. Audio-Visual

International Nuclear Information System (INIS)

1990-01-01

The videotape is divided into five sections. Section 1 provides definitions and historical information on both the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The four types of RCRA regulatory programs - Subtitles C, D, I, and J - are described. Treatment, storage, and disposal (TSD) and recycling facilities are also discussed. Section 2 discusses the history behind the Emergency Planning and Community Right-to-Know Act (Title III). The four major provisions of Title III, which are emergency planning, emergency release notification, community right-to-know reporting, and the toxic chemical release inventory are covered. Section 3 outlines the UST program covering notification, record keeping, and the UST Trust Fund. Section 4 outlines the six major provisions of the Clean Water Act (CWA): water quality, pretreatment, prevention of oil and hazardous substance discharges, responses to oil and hazardous substance discharges, discharges of hazardous substances into the ocean, and dredge and fill. Section 5 explains the purpose, regulations, and standards of the Safe Drinking Water Act (SDWA). Specific issues such as underground injection, sole source aquifers, and lead contamination are discussed

Resource Conservation and Recovery Act (RCRA) Part B Permit Application for Production Associated Units at the Oak Ridge Y-12 Plant

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

This is the RCRA required permit application for Radioactive and Hazardous Waste Management at the Oak Ridge Y-12 Plant for the following units: Building 9206 Container Storage Unit; Building 9212 Container Storage Unit; Building 9720-12 Container Storage Unit; Cyanide Treatment Unit. All four of these units are associated with the recovery of enriched uranium and other metals from wastes generated during the processing of nuclear materials.

Resource Conservation and Recovery Act (RCRA) Part B Permit Application for Production Associated Units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1994-09-01

This is the RCRA required permit application for Radioactive and Hazardous Waste Management at the Oak Ridge Y-12 Plant for the following units: Building 9206 Container Storage Unit; Building 9212 Container Storage Unit; Building 9720-12 Container Storage Unit; Cyanide Treatment Unit. All four of these units are associated with the recovery of enriched uranium and other metals from wastes generated during the processing of nuclear materials

RCRA Facilities Assessment (RFA), Oak Ridge National Laboratory, container storage accumulation areas

International Nuclear Information System (INIS)

1987-01-01

The Oak Ridge National Laboratory (ORNL) remedial action strategy is based on a memorandum from the Environmental Protection Agency (EPA) to the Department of Energy (DOE) in which EPA elected to enforce regulatory requirements for ORNL through its amended Resource Conservation and Recovery Act (RCRA) authority. This report, which completes the requirements of II.A.1 of the Hazardous and Solid Waste Amendments (HSWA) permit, identifies areas near the point of waste generation in which wastes are accumulated before they are transferred into the permitted waste storage facilities. In includes background information on each area and an assessment of the need for further remedial attention. The waste accumulation areas described in this addendum bear identification numbers indicative of the WAGs of which they are a part. Waste accumulation areas that are located inside a building and in which there is no potential for releases to the environment are not included in this report

OpenTURNS, an open source uncertainty engineering software

International Nuclear Information System (INIS)

Popelin, A.L.; Dufoy, A.

2013-01-01

The needs to assess robust performances for complex systems have lead to the emergence of a new industrial simulation challenge: to take into account uncertainties when dealing with complex numerical simulation frameworks. EDF has taken part in the development of an Open Source software platform dedicated to uncertainty propagation by probabilistic methods, named OpenTURNS for Open source Treatment of Uncertainty, Risk and Statistics. OpenTURNS includes a large variety of qualified algorithms in order to manage uncertainties in industrial studies, from the uncertainty quantification step (with possibilities to model stochastic dependence thanks to the copula theory and stochastic processes), to the uncertainty propagation step (with some innovative simulation algorithms as the ziggurat method for normal variables) and the sensitivity analysis one (with some sensitivity index based on the evaluation of means conditioned to the realization of a particular event). It also enables to build some response surfaces that can include the stochastic modeling (with the chaos polynomial method for example). Generic wrappers to link OpenTURNS to the modeling software are proposed. At last, OpenTURNS is largely documented to provide rules to help use and contribution

Helpful Entry Level Skills Checklist--Revised Manual [and] Helpful Entry Level Skill Checklist--Revised Edition.

Science.gov (United States)

Child Development Centers of the Bluegrass, Lexington, KY.

The Helpful Entry Level Skills Checklist was designed to assist preschool teachers in selecting functional skills that children (including children with disabilities) may need to make a successful transition into the public schools. These skills, for the most part, deal with attending, compliance, ability to follow directions, turn taking, ability…

Revised RCRA closure plan for the Interim Drum Yard (S-030) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Smith, C.M.

1994-09-01

The Interim Drum Yard (IDY) facility is a containerized waste storage area located in the Y-12 exclusion area. It was used to store waste materials which are regulated by RCRA (Resource Conservation and Recovery Act); uranyl nitrate solutions were also stored there. The closure plan outlines the actions required to achieve closure of IDY and is being submitted in accordance with TN Rule 1200-1-11.05(7) and 40 CFR 265.110

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

Custom Search Results Help | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

Identification, classification and management of industrial waste in Kavir steel complex according to the Bazel convention and RCRA

Directory of Open Access Journals (Sweden)

Mohammad Hasan Ehrampoush

2016-06-01

Full Text Available Introduction: Requiring industries for implementing industrial waste management programs and planning for proper waste disposal is essential in order to achieve sustainable development. Therefore, industrial waste management program was done in Kavir Steel Complex, in Aran va Bidgol region to identify and classify industrial waste and also to present solutions for improving waste management. In this complex, production process is hot rolling steel and the product is rebar. Material and Method: The preset study was conducted in Kavir Steel Complex. Following survey of production process and sources of waste, the type and volume of produced waste were identified and measured during 3 months. Then, the classification of wastes was done according to the Bazel Convention and Resource Conservation and Recovery Act (RCRA, and finally new industrial & health solid waste management program was presented. Result: Considering the volume, industrial waste of production process in Kavir Steel Complex was between 130 to 180 grams per each ton of rebar. Main industrial waste included oxide of steel billet, industrial sludge, used oil and lubricant which were classified according to the RCRA: 8 materials with T code, 1 with C code, 5 with I code and 3 materials with C code. Conclusion: The results revealed that the most amount of industrial waste in Kavir Steel Complex is the waste of steel billet and industrial sludge, and more than 90% of Kavir steel industrial waste were reused and recycled inside or outside of this complex. It is recommended that used oil to be transport and maintain in the safe containers.

RCRA Part B permit modifications for cost savings and increased flexibility at the Rocky Flats Environmental Technology Site

International Nuclear Information System (INIS)

Jierree, C.; Ticknor, K.

1996-10-01

With shrinking budgets and downsizing, a need for streamlined compliance initiatives became evident at the Rocky Flats Environmental Technology Site (RFETS). Therefore, Rocky Mountain Remediation Services (RMRS) at the RFETS successfully and quickly modified the RFETS RCRA Part B Permit to obtain significant cost savings and increased flexibility. This 'was accomplished by requesting operations personnel to suggest changes to the Part B Permit which did not diminish overall compliance and which would be most. cost beneficial. The U.S. Department of Energy (DOE) subsequently obtained approval of those changes from the Colorado Department of Public Health and the Environment (CDPHE)

Mobilization plan for the Y-12 9409-5 tank storage facility RCRA closure plan. Final report. Revision 1

International Nuclear Information System (INIS)

1993-11-01

This mobilization plan identifies the activities and equipment necessary to begin the field sampling for the Oak Ridge Y-12 9409-5 Diked Tank Storage Facility (DTSF) Resource Conservation and Recovery Act (RCRA) closure. Elements of the plan outline the necessary components of each mobilization task and identify whether SAIC or the Martin Marietta Energy Systems, Inc. Y-12 Environmental Restoration Division will be responsible for task coordination. Field work will be conducted in two phases: mobilization phase and soil sampling phase. Training and medical monitoring, access, permits and passes, decontamination/staging area, equipment, and management are covered in this document

RCRA materials analysis by laser-induced breakdown spectroscopy: Detection limits in soils

International Nuclear Information System (INIS)

Koskelo, A.; Cremers, D.A.

1994-01-01

The goal of the Technical Task Plan (TTP) that this report supports is research, development, testing and evaluation of a portable analyzer for RCRA and other metals. The instrumentation to be built will be used for field-screening of soils. Data quality is expected to be suitable for this purpose. The data presented in this report were acquired to demonstrate the detection limits for laser-induced breakdown spectroscopy (LIBS) of soils using instrument parameters suitable for fieldable instrumentation. The data are not expected to be the best achievable with the high pulse energies available in laboratory lasers. The report presents work to date on the detection limits for several elements in soils using LIBS. The elements targeted in the Technical Task Plan are antimony, arsenic, beryllium, cadmium, chromium, lead, selenium, and zirconium. Data for these elements are presented in this report. Also included are other data of interest to potential customers for the portable LIBS apparatus. These data are for barium, mercury, cesium and strontium. Data for uranium and thorium will be acquired during the tasks geared toward mixed waste characterization

RCRA land unit closures at the Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Welch, S.H.; Kelly, B.A.; Delozier, M.F.P.; Manrod, W.E.

1987-01-01

Eight land-based hazardous waste management units at the Y-12 Plant are being closed under an integrated multi-year program. Closure plans for the units have been submitted and are in various stages of revision and regulatory review. These units will be closed by various combinations of methods, including liquid removal and treatment, sludge stabilization, contaminated sludge and/or soil removal, and capping. The closure of these sites will be funded by a new Department of Energy budget category, the Environmental Restoration Budget Category (ERBC), which is intended to provide greater flexibility in the response to closure and remedial activities. A major project, Closure and Post-Closure Activities (CAPCA), has been identified for ERBC funding to close and remediate the land units in accordance with RCRA requirements. Establishing the scope of this program has required the development of a detailed set of assumptions and a confirmation program for each assumption. Other significant activities in the CAPCA program include the development of risk assessments and the preparation of an integrated schedule

Detailed analysis of a RCRA landfill for the United Nuclear Corporation Disposal Site at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1991-04-01

The purpose of this detailed analysis is to provide a preliminary compilation of data, information, and estimated costs associated with a RCRA landfill alternative for UNC Disposal Site. This is in response to Environmental Protection Agency (EPA) comment No. 6 from their review of a open-quotes Feasibility Study for the United Nuclear Corporation Disposal Site at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee.close quotes

Using support vector machine to predict beta- and gamma-turns in proteins.

Science.gov (United States)

Hu, Xiuzhen; Li, Qianzhong

2008-09-01

By using the composite vector with increment of diversity, position conservation scoring function, and predictive secondary structures to express the information of sequence, a support vector machine (SVM) algorithm for predicting beta- and gamma-turns in the proteins is proposed. The 426 and 320 nonhomologous protein chains described by Guruprasad and Rajkumar (Guruprasad and Rajkumar J. Biosci 2000, 25,143) are used for training and testing the predictive model of the beta- and gamma-turns, respectively. The overall prediction accuracy and the Matthews correlation coefficient in 7-fold cross-validation are 79.8% and 0.47, respectively, for the beta-turns. The overall prediction accuracy in 5-fold cross-validation is 61.0% for the gamma-turns. These results are significantly higher than the other algorithms in the prediction of beta- and gamma-turns using the same datasets. In addition, the 547 and 823 nonhomologous protein chains described by Fuchs and Alix (Fuchs and Alix Proteins: Struct Funct Bioinform 2005, 59, 828) are used for training and testing the predictive model of the beta- and gamma-turns, and better results are obtained. This algorithm may be helpful to improve the performance of protein turns' prediction. To ensure the ability of the SVM method to correctly classify beta-turn and non-beta-turn (gamma-turn and non-gamma-turn), the receiver operating characteristic threshold independent measure curves are provided. (c) 2008 Wiley Periodicals, Inc.

Are Mentor Relationships Helping Organizations? An Exploration of Developing Mentee-Mentor-Organizational Identifications Using Turning Point Analysis.

Science.gov (United States)

Bullis, Connie; Bach, Betsy Wackernagel

1989-01-01

Examines developing mentor relationships and the association between mentor relationships and individual-organizational relationships. Indicates that many turning points occur later than proposed in broad-phase models of mentor relationship development. Finds that mentor relationships should not be assumed to benefit organizations. (SR)

Water Pollution Search Criteria Help | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

Help Content for ECHO Reports | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

Modeling of residual stress state in turning of 304L

International Nuclear Information System (INIS)

Valiorgue, F.; Rech, J.; Bergheau, J.M.

2010-01-01

Research presented in this paper aims to link machining parameters to residual stress state and helps understanding mechanisms responsible of machined surface properties modifications. The first presented works are based on an experimental campaign. They reproduce the finishing turning operation of 304L and allow observing the residual stress state evolution at the work piece surface and for an affected depth of 0.2 mm for such processes. Then, the finishing turning operation is simulated numerically in order to realize the same sensitivity study to cutting parameters. This simulation is based on an hybrid approach mixing experimental data and numerical simulation. This method allows getting round the classical difficulties of turning simulation by applying equivalent thermo mechanical loadings onto the work piece surface without modeling the material separation phenomena. Moreover the numerical model uses an hardening law taking into account dynamic recrystallization phenomena. (authors)

RCRA Closure Plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-04-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. In January 1993, the Closure Plan was revised to include inspection and maintenance criteria and to reflect that future monitoring and remediation would be conducted as part of the ongoing Comprehensive Environmental Response, Compensation, and Liability Act activities at the Oak Ridge Y-12 Plant. This Closure Plan revision is intended to reflect the placement of the Kerr Hollow Quarry debris at the Walk-In Pits, revise the closure dates, and acknowledge that the disposition of a monitoring well within the closure site cannot be verified

SNS 2.1K Cold Box Turn-down Studies

International Nuclear Information System (INIS)

F. Casagrande; P.A. Gurd; D.R. Hatfield; M.P. Howell; W.H. Strong; D. Arenius; J. Creel; V. Ganni; P. Knudsen

2006-01-01

The Spallation Neutron Source (SNS) at Oak Ridge National Laboratory is nearing completion. The cold section of the Linac consists of 81 superconducting radio frequency cavities cooled to 2.1K by a 2400 watt cryogenic refrigeration system. The 2.1K cold box consists of four stages of centrifugal compressors with LN2-cooled variable speed electric motors and magnetic bearings. The cryogenic system successfully supported the Linac beam commissioning at both 4.2K and 2.1K and has been fully operational since June 2005. This paper describes the control principles utilized and the experimental results obtained for the SNS cold compressors turn-down capability to about 30% of the design flow, and possible limitation of the frequency dependent power factor of the cold compressor electric motors, which was measured for the first time during commissioning. These results helped to support the operation of the Linac over a very broad and stable cold compressor operating flow range (refrigeration capacity) and pressure. This in turn helped to optimize the cryogenic system operating parameters, minimizing the utilities and improving the system reliability and availability

The Translator's Turn: in the Cultural Turn

Institute of Scientific and Technical Information of China (English)

徐玮玮

2003-01-01

@@ Introduction: Douglas Robinson rose to the defense of the " atheoretical" American literary translator in The Translator's Turn (1991). Here, I borrowed the title from him, but I will write my paper in the thought of the translator's role in translating. In his book, Robinson argued that the literary translator embodies an integration of feeling and thought, of intuition and systematization. In analyzing the " turn" that the translator take from the source text to the target text, Robinson offered a " dialogical" model, that is the translator's dialogical engagement with the source language and with the ethic of the target language. Robinson allows for the translator to intervene, subvert, divert, even entertain, emphasizing the creative aspect of literary translation. The translation linguists, scientists, and philosophers have had their chance at translation theory; now it is time, he argued, for the literary translators to have their " turn".

A RCRA clean closure of a unique site - Kerr Hollow quarry at the Y-12 Plant

International Nuclear Information System (INIS)

Stone, J.E.; Yemington, C.

1991-01-01

An abandoned rock quarry, Kerr Hollow Quarry (KHQ), near the DOE Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, was used from 1951-1988 as a site to treat RCRA wastes which were reactive, corrosive, or ignitable and which posed major concerns for personnel safety. The wastes were generated from operations at the Y-12 Plant and Oak Ridge National Laboratory and were previously treated by allowing the wastes to react with the water in KHQ. When closure of the site was required by the RCRA regulations, a closure method was selected to allow for clean closure of the quarry without treatment or removal of the water in KHQ. The method proposed to and approved by the Tennessee Department of Health and Environment (TDHE) was one of surveying the containers in the quarry by a submersible Remotely Operated Vehicle (ROV) using sonar and visually inspecting the containers by camera to confirm that all containers are breached and empty. Any container found intact would be breached to allow the contents to react with water and form non-hazardous residue. The progress of this unique type of closure is presented along with a summary of the problems encountered, planning activities, equipment utilized and other information about the closure. All work was done with remotely operated equipment. This work is being performed by Sonsub, Inc. This closure project showed the practicality and cost benefits of telerobotic systems for work on hazardous waste sites. In addition to the intangible benefit of reduced exposure of workers, insurance costs are much lower and efficiency is higher. Daily start-up time is reduced since there is no need to don protective suits or other gear. Productivity is higher since personnel work only in clean areas where they are not hampered by protective gear. Cleanup time at shift end is minimized since the remote equipment does not leave the hazardous area and personnel need not go through decontamination

RCRA and operational monitoring (ROM): Multi-year program plan and fiscal year 96 work plan. WBS 1.5.3, Revision 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The RCRA & Operational Monitoring (ROM) Program Office manages the Hanford Site direct funded Resource Conservation and Recovery Act (RCRA) and Operational Monitoring under Work Breakdown Structure (WBS) 1.01.05.03. The ROM Program Office is included in Hanford Technical Services, a part of Projects & Site Services of Westinghouse Hanford Company (WHC). The 1996 Multi-Year Program Plan (MYPP) includes the Fiscal Year Work Plan (FYWP). The Multi-Year Program Plan takes its direction from the Westinghouse Planning Baseline Integration Organization. The MYPP provides both the near term, enhanced details and the long term, projected details for the Program Office to use as baseline Cost, Scope and Schedule. Change Control administered during the fiscal year is against the baseline provided by near term details of this document. The MYPP process has been developed by WHC to meet its internal planning and integration needs and complies with the requirements of the US Department of Energy, Richland Operations Office (RL) Long Range Planning Process Directive (RLID 5000.2). Westinghouse Hanford Company (WHC) has developed the multi-year planning process for programs to establish the technical, schedule and cost baselines for program and support activities under WHC`s scope of responsibility. The baseline information is developed by both WHC indirect funded support services organization, and direct funded programs in WHC. WHC Planning and Integration utilizes the information presented in the program specific MYPP and the Program Master Baseline Schedule (PMBS) to develop the Site-Wide Integrated Schedule.

RCRA and operational monitoring (ROM): Multi-year program plan and fiscal year 96 work plan. WBS 1.5.3, Revision 1

International Nuclear Information System (INIS)

1995-09-01

The RCRA ampersand Operational Monitoring (ROM) Program Office manages the Hanford Site direct funded Resource Conservation and Recovery Act (RCRA) and Operational Monitoring under Work Breakdown Structure (WBS) 1.01.05.03. The ROM Program Office is included in Hanford Technical Services, a part of Projects ampersand Site Services of Westinghouse Hanford Company (WHC). The 1996 Multi-Year Program Plan (MYPP) includes the Fiscal Year Work Plan (FYWP). The Multi-Year Program Plan takes its direction from the Westinghouse Planning Baseline Integration Organization. The MYPP provides both the near term, enhanced details and the long term, projected details for the Program Office to use as baseline Cost, Scope and Schedule. Change Control administered during the fiscal year is against the baseline provided by near term details of this document. The MYPP process has been developed by WHC to meet its internal planning and integration needs and complies with the requirements of the US Department of Energy, Richland Operations Office (RL) Long Range Planning Process Directive (RLID 5000.2). Westinghouse Hanford Company (WHC) has developed the multi-year planning process for programs to establish the technical, schedule and cost baselines for program and support activities under WHC's scope of responsibility. The baseline information is developed by both WHC indirect funded support services organization, and direct funded programs in WHC. WHC Planning and Integration utilizes the information presented in the program specific MYPP and the Program Master Baseline Schedule (PMBS) to develop the Site-Wide Integrated Schedule

Quarterly report of RCRA groundwater monitoring data for period January 1, 1993 through March 31, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-07-01

Hanford Site interim-status groundwater monitoring projects are conducted as either background, indicator parameter evaluation, or groundwater quality assessment monitoring programs as defined in the Resource Conservation and Recovery Act of 1976 (RCRA); and Interim Status Standards for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities, as amended (40 Code of Federal Regulations [CFR] 265). Compliance with the 40 CFR 265 regulations is required by the Washington Administrative Code (WAC) 173-303. This report contains data from Hanford Site groundwater monitoring projects. This quarterly report contains data received between March 8 and May 24, 1993, which are the cutoff dates for this reporting period. This report may contain not only data from the January through March quarter but also data from earlier sampling events that were not previously reported.

RCRA permitting strategies for the development of innovative technologies: Lessons from Hanford

International Nuclear Information System (INIS)

Gajewski, S.W.; Donaghue, J.F.

1994-01-01

The Hanford Site restoration is the largest waste cleanup operation in history. The Hanford plutonium production mission generated two-thirds of all the nuclear waste, by volume, in the Department of Energy (DOE) Complex. Cleanup challenges include not only large stored volumes of radioactive, hazardous, and mixed waste, but contaminated soil and groundwater and scores of major structures slated for decontamination, decommissioning, and demolition. DOE and its contractors will need to invent the technology required to do the job on a timetable driven by negotiated milestones, public concerns, and budgetary constraints. This paper will discuss the effort at Hanford to develop an integrated, streamlined strategy for compliance with the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) in the conduct of research, development, and demonstration (RD ampersand D) of innovative cleanup technologies. The aspects that will be discussed include the following: the genesis of the RD ampersand D permitting challenge at Hanford; permitting options in the existing regulatory framework; regulatory options that offered the best fit for Hanford RD ampersand D activities, and the problems associated with them; and conclusions and recommendations made to regulatory bodies

Characterization of Vadose Zone Sediment: Uncontaminated RCRA Borehole Core Samples and Composite Samples

International Nuclear Information System (INIS)

Serne, R. Jeffrey; Bjornstad, Bruce N.; Schaef, Herbert T.; Williams, Bruce A.; Lanigan, David C.; Horton, Duane G.; Clayton, Ray E.; Mitroshkov, Alexandre V.; Legore, Virginia L.; O'Hara, Matthew J.; Brown, Christopher F.; Parker, Kent E.; Kutnyakov, Igor V.; Serne, Jennifer N.; Last, George V.; Smith, Steven C.; Lindenmeier, Clark W.; Zachara, John M.; Burke, Deborah S.

2008-01-01

This report was revised in September 2008 to remove acid-extractable sodium data from Tables 4.14, 4.16, 5.20, 5.22, 5.43, and 5.45. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in February 2002. The overall goal of the of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities. To meet this goal, CH2M HILL Hanford Group, Inc. asked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediment from within the S-SX Waste Management Area. This report is one in a series of four reports to present the results of these analyses. Specifically, this report contains all the geologic, geochemical, and selected physical characterization data collected on vadose zone sediment recovered from Resource Conservation and Recovery Act (RCRA) borehole bore samples and composite samples

Characterization of Vadose Zone Sediment: Uncontaminated RCRA Borehole Core Samples and Composite Samples

Energy Technology Data Exchange (ETDEWEB)

Serne, R. Jeffrey; Bjornstad, Bruce N.; Schaef, Herbert T.; Williams, Bruce A.; Lanigan, David C.; Horton, Duane G.; Clayton, Ray E.; Mitroshkov, Alexandre V.; Legore, Virginia L.; O' Hara, Matthew J.; Brown, Christopher F.; Parker, Kent E.; Kutnyakov, Igor V.; Serne, Jennifer N.; Last, George V.; Smith, Steven C.; Lindenmeier, Clark W.; Zachara, John M.; Burke, Deborah S.

2008-09-11

This report was revised in September 2008 to remove acid-extractable sodium data from Tables 4.14, 4.16, 5.20, 5.22, 5.43, and 5.45. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in February 2002. The overall goal of the of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities. To meet this goal, CH2M HILL Hanford Group, Inc. asked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediment from within the S-SX Waste Management Area. This report is one in a series of four reports to present the results of these analyses. Specifically, this report contains all the geologic, geochemical, and selected physical characterization data collected on vadose zone sediment recovered from Resource Conservation and Recovery Act (RCRA) borehole bore samples and composite samples.

1993 RCRA Part B permit renewal application, Savannah River Site: Volume 10, Consolidated Incineration Facility, Section C, Revision 1

International Nuclear Information System (INIS)

Molen, G.

1993-08-01

This section describes the chemical and physical nature of the RCRA regulated hazardous wastes to be handled, stored, and incinerated at the Consolidated Incineration Facility (CIF) at the Savannah River Site. It is in accordance with requirements of South Carolina Hazardous Waste Management Regulations R.61-79.264.13(a) and(b), and 270.14(b)(2). This application is for permit to store and teat these hazardous wastes as required for the operation of CIF. The permit is to cover the storage of hazardous waste in containers and of waste in six hazardous waste storage tanks. Treatment processes include incineration, solidification of ash, and neutralization of scrubber blowdown

Why humans might help strangers

Directory of Open Access Journals (Sweden)

Nichola Jayne Raihani

2015-02-01

Full Text Available Humans regularly help strangers, even when interactions are apparently unobserved and unlikely to be repeated. Such situations have been simulated in the laboratory using anonymous one-shot games (e.g. prisoner's dilemma where the payoff matrices used make helping biologically altruistic. As in real-life, participants often cooperate in the lab in these one-shot games with non-relatives, despite that fact that helping is under negative selection under these circumstances. Two broad explanations for such behavior prevail. The 'big mistake' or 'mismatch' theorists argue that behavior is constrained by psychological mechanisms that evolved predominantly in the context of repeated interactions with known individuals. In contrast, the cultural group selection theorists posit that humans have been selected to cooperate in anonymous one-shot interactions due to strong between-group competition, which creates interdependence among in-group members. We present these two hypotheses before discussing alternative routes by which humans could increase their direct fitness by cooperating with strangers under natural conditions. In doing so, we explain why the standard lab games do not capture real-life in various important aspects. First, asymmetries in the cost of perceptual errors regarding the context of the interaction (one-shot versus repeated; anonymous versus public might have selected for strategies that minimize the chance of making costly behavioral errors. Second, helping strangers might be a successful strategy for identifying other cooperative individuals in the population, where partner choice can turn strangers into interaction partners. Third, in many real-world situations individuals are able to parcel investments such that a one-shot interaction is turned into a repeated game of many decisions. Finally, in contrast to the assumptions of the prisoner's dilemma model, it is possible that benefits of cooperation follow a non-linear function of

Water Pollution Search Results Help - TRI | ECHO | US EPA

Science.gov (United States)

ECHO, Enforcement and Compliance History Online, provides compliance and enforcement information for approximately 800,000 EPA-regulated facilities nationwide. ECHO includes permit, inspection, violation, enforcement action, and penalty information about facilities regulated under the Clean Air Act (CAA) Stationary Source Program, Clean Water Act (CWA) National Pollutant Elimination Discharge System (NPDES), and/or Resource Conservation and Recovery Act (RCRA). Information also is provided on surrounding demographics when available.

Lattice modeling and calibration with turn-by-turn orbit data

Directory of Open Access Journals (Sweden)

Xiaobiao Huang

2010-11-01

Full Text Available A new method that explores turn-by-turn beam position monitor (BPM data to calibrate lattice models of accelerators is proposed. The turn-by-turn phase space coordinates at one location of the ring are first established using data from two BPMs separated by a simple section with a known transfer matrix, such as a drift space. The phase space coordinates are then tracked with the model to predict positions at other BPMs, which can be compared to measurements. The model is adjusted to minimize the difference between the measured and predicted orbit data. BPM gains and rolls are included as fitting variables. This technique can be applied to either the entire or a section of the ring. We have tested the method experimentally on a part of the SPEAR3 ring.

Lattice modeling and calibration with turn-by-turn orbit data

Science.gov (United States)

Huang, Xiaobiao; Sebek, Jim; Martin, Don

2010-11-01

A new method that explores turn-by-turn beam position monitor (BPM) data to calibrate lattice models of accelerators is proposed. The turn-by-turn phase space coordinates at one location of the ring are first established using data from two BPMs separated by a simple section with a known transfer matrix, such as a drift space. The phase space coordinates are then tracked with the model to predict positions at other BPMs, which can be compared to measurements. The model is adjusted to minimize the difference between the measured and predicted orbit data. BPM gains and rolls are included as fitting variables. This technique can be applied to either the entire or a section of the ring. We have tested the method experimentally on a part of the SPEAR3 ring.

RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site: Proposed Mixed Waste Disposal Unit (MWSU)

Energy Technology Data Exchange (ETDEWEB)

NSTec Environmental Management

2010-07-19

The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When the proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.

RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site: Proposed Mixed Waste Disposal Unit (MWSU)

International Nuclear Information System (INIS)

2010-01-01

The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When the proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.

Turning a page of Agency history

Energy Technology Data Exchange (ETDEWEB)

NONE

1969-07-01

Recent developments, and especially the new and critical interest of developing countries, have helped to mark the turning of a page in the Agency's history. If the present situation in the economics of nuclear power does not change there is a danger that developing countries will lag further and further behind the advanced countries in its use. Shortage of resources impose a brake on Agency efforts to promote benefits of nuclear techniques, especially by technical assistance. These were some of the points made by Dr. Sigvard Eklund, the Director General, when he presented the Agency's annual report to the Economic and Social Council (ECOSOC) in July. (author)

Biomechanical Evaluation of a Bed Feature to Assist in Turning and Laterally Repositioning Patients.

Science.gov (United States)

Wiggermann, Neal

2016-08-01

This study investigated the effects of hospital bed features on the biomechanical stresses experienced by nurses when turning and laterally repositioning patients. Turn Assist, a common feature in ICU beds that helps to rotate patients, and side rail orientation were evaluated. Manual patient handling is a risk factor for musculoskeletal injury, and turning patients is one of the most common patient handling activities. No known studies have evaluated bed attributes such as the Turn Assist feature and side rail orientation that may affect the stresses experienced by the nurse. Nine female nurses laterally repositioned and turned a 63-kg and 123-kg subject on an ICU bed while motion capture, ground reaction forces, and hand force data were recorded. Loading of the spine and shoulder was modeled using 3D Static Strength Prediction Program (3DSSPP). Spine compression and shear forces did not exceed recommended limits when turning or laterally repositioning. However, the mean pull forces required to manually laterally reposition even the 63-kg subject was 340 Newtons, more than 50% greater than limits established in psychophysical testing. Turn Assist considerably reduced spine loading and pull forces for both turning and laterally repositioning. Lowering side rails reduced spinal compression by 11% when turning patients. Laterally repositioning patients as part of turning may pose an injury risk to caregivers. Turn Assist reduces physical loading on nurses when turning and repositioning patients. Caregivers should consider using Turn Assist and other aids such as mechanical lifts or sliding sheets especially when turning patients requires lateral repositioning. © 2015, Human Factors and Ergonomics Society.

"Depression Can Disguise Itself…" —But There Is Help

Science.gov (United States)

... of this page please turn Javascript on. Feature: Depression "Depression Can Disguise Itself…" —But There Is Help Past ... 20 million Americans. What are the signs of depression? Sadness or inability to enjoy things are hallmarks ...

Mimicry by asx- and ST-turns of the four main types of beta-turn in proteins.

Science.gov (United States)

Duddy, William J; Nissink, J Willem M; Allen, Frank H; Milner-White, E James

2004-11-01

Hydrogen-bonded beta-turns in proteins occur in four categories: type I (the most common), type II, type II', and type I'. Asx-turns resemble beta-turns, in that both have an NH. . .OC hydrogen bond forming a ring of 10 atoms. Serine and threonine side chains also commonly form hydrogen-bonded turns, here called ST-turns. Asx-turns and ST-turns can be categorized into four classes, based on side chain rotamers and the conformation of the central turn residue, which are geometrically equivalent to the four types of beta-turns. We propose asx- and ST-turns be named using the type I, II, I', and II' beta-turn nomenclature. Using this, the frequency of occurrence of both asx- and ST-turns is: type II' > type I > type II > type I', whereas for beta-turns it is type I > type II > type I' > type II'. Almost all type II asx-turns occur as a recently described three residue feature named an asx-nest.

Fall 2010 Semiannual (III.H. and I.U.) Report for the HWMA/RCRA Post Closure Permit for the INTEC Waste Calcining Facility and the CPP 601/627/640 Facility at the INL Site

Energy Technology Data Exchange (ETDEWEB)

Boehmer, Ann

2010-11-01

The Waste Calcining Facility is located at the Idaho Nuclear Technology and Engineering Center. In 1999, the Waste Calcining Facility was closed under an approved Hazardous Waste Management Act/Resource Conservation and Recovery Act (HWMA/RCRA) Closure Plan. Vessels and spaces were grouted and then covered with a concrete cap. The Idaho Department of Environmental Quality issued a final HWMA/RCRA post-closure permit on September 15, 2003, with an effective date of October 16, 2003. This permit sets forth procedural requirements for groundwater characterization and monitoring, maintenance, and inspections of the Waste Calcining Facility to ensure continued protection of human health and the environment. The post closure permit also includes semiannual reporting requirements under Permit Conditions III.H. and I.U. These reporting requirements have been combined into this single semiannual report, as agreed between the Idaho Cleanup Project and Idaho Department of Environmental Quality. The Permit Condition III.H. portion of this report includes a description and the results of field methods associated with groundwater monitoring of the Waste Calcining Facility. Analytical results from groundwater sampling, results of inspections and maintenance of monitoring wells in the Waste Calcining Facility groundwater monitoring network, and results of inspections of the concrete cap are summarized. The Permit Condition I.U. portion of this report includes noncompliances not otherwise required to be reported under Permit Condition I.R. (advance notice of planned changes to facility activity which may result in a noncompliance) or Permit Condition I.T. (reporting of noncompliances which may endanger human health or the environment). This report also provides groundwater sampling results for wells that were installed and monitored as part of the Phase 1 post-closure period of the landfill closure components in accordance with HWMA/RCRA Landfill Closure Plan for the CPP-601 Deep

Low temperature setting iron phosphate ceramics as a stabilization and solidification agent for incinerator ash contaminated with transuranic and RCRA metals

International Nuclear Information System (INIS)

Medvedev, P.G.; Hansen, M.; Wood, E.L.; Frank, S.M.; Sidwell, R.W.; Giglio, J.J.; Johnson, S.G.; Macheret, J.

1997-01-01

Incineration of combustible Mixed Transuranic Waste yields an ash residue that contains oxides of Resource Conservation and Recovery Act (RCRA) and transuranic metals. In order to dispose of this ash safely, it has to be solidified and stabilized to satisfy appropriate requirements for repository disposal. This paper describes a new method for solidification of incinerator ash, using room temperature setting iron phosphate ceramics, and includes fabrication procedures for these waste forms as well as results of the MCC-1 static leach test, XRD analysis, scanning electron microscopy studies and density measurements of the solidified waste form produced

Quarterly report of RCRA groundwater monitoring data for period October 1, 1992--December 31, 1992

International Nuclear Information System (INIS)

1993-04-01

Hanford Site interim-status groundwater monitoring projects are conducted as either background, indicator parameter evaluation, or groundwater quality assessment monitoring programs as defined in the Resource Conservation and Recovery Act of 1976 (RCRA); and Interim Status Standards for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities, as amended (40 CFR 265). Compliance with the 40 CFR 265 regulations is required by the Washington Administrative Code (WAC) 173-303. Long-term laboratory contracts were approved on October 22, 1991. DataChem Laboratories of Salt Lake City, Utah, performs the hazardous chemicals analyses for the Hanford Site. Analyses for coliform bacteria are performed by Columbia/Biomedical Laboratories and for dioxin by TMS Analytical Services, Inc. International Technology Analytical Services Richland, Washington performs the radiochemical analyses. This quarterly report contains data that were received prior to March 8, 1993. This report may contain not only data from the October through December quarter but also data from earlier sampling events that were not previously reported

Turning breech babies after 34 weeks: the if, how, & when of turning breech babies.

Science.gov (United States)

Cohain, Judy Slome

2007-01-01

Techniques for turning a term breech baby are 1). External cephalic version (ECV) using hands and ultrasound only; 2). Acupuncture point stimulation, by needle or moxibustion; 3). Chiropractic "Webster" technique; 4). Hypnotherapy; and 5). Special exercises. Fifty % of breech fetuses at 34 weeks will turn by themselves to head down by 38 weeks. Therefore, to be considered effective, a technique for turning breech must turn the baby and keep it turned more than 50% of the time. Only ECV with an experienced practitioner has been documented to have a greater than 50% success rate at 37 weeks; in 95% of cases the head stays down. Most women experience the fetus turning by hand as quick but very painful. "Unstable lie" is sometimes used as a baseless excuse for inducing labor after the baby turns from breech to head down. (judyslome@hotmail.com).

How changes in top water bother big turning packs of up-going wet air

Science.gov (United States)

Wood, K.

2017-12-01

Big turning packs of up-going wet air form near areas of warm water at the top of big bodies of water. After these turning packs form, they usually get stronger if the top water stays warm. If the top water becomes less warm, the turning packs usually get less strong. Other things can change how strong a turning pack gets, like how wet the air around it is and if that air moves faster higher up than lower down. When these turning packs hit land, their rain and winds can hurt people and the stuff they own, especially if the turning pack is really strong. But it's hard to know how much stronger or less strong it will become before it hits land. Warm top water gives a turning pack of up-going wet air a lot of power, but cool top water doesn't, so we need to know how warm the top water is. Because I can't go into every turning pack myself, flying computers in outer space tell me what the top water is doing. I look at the top water near turning packs that get strong and see how it's different from the top water near those that get less strong. Top water that changes from warm to cool in a small area bothers a turning pack of up-going wet air, which then gets less strong. If we see these top water changes ahead of time, that might help us know what a turning pack will do before it gets close to land.

An example of system integration for RCRA policy analysis

International Nuclear Information System (INIS)

Tonn, B.; Goeltz, R.; Schmidt, K.

1991-01-01

This paper describes the synthesis of various computer technologies and software systems used on a project to estimate the costs of remediating Solid Waste Management Units (SWMUs) that fall under the corrective action provisions of the Resource Conservation and Recovery Act (RCRA). The project used two databases collected by Research Triangle Institute (RTI) that contain information on SWMUs and a PC-based software system called CORA that develops cost estimates for remediating SWMUs. The project team developed rules to categorize every SWMU in the databases by the kinds of technologies required to clean them up. These results were input into CORA, which estimated costs associated with the technologies. Early on, several computing challenges presented themselves. First, the databases have several hundred thousand records each. Second, the categorization rules could not be written to cover all combinations of variables. Third, CORA is run interactively and the analysis plan called for running CORA tens of thousands of times. Fourth, large data transfers needed to take place between RTI and Oak Ridge National Laboratory. Solutions to these problems required systems integration. SWMU categorization was streamlined by using INTERNET as was the data transfer. SAS was used to create files used by a program called SuperKey that was used to run CORA. Because the analysis plan required the generation of hundreds of thousands of cost estimates, memory management software was needed to allow the portable IBM P70 to do the job. During the course of the project, several other software packages were used, including: SAS System for Personal Computers (SAS/PC), DBase III, LOTUS 1-2-3, PIZAZZ PLUS, LOTUS Freelance Plus, and Word Perfect. Only the comprehensive use of all available hardware and software resources allowed this project to be completed within the time and budget constraints. 5 refs., 3 figs., 3 tabs

Determination of linear optics functions from turn-by-turn data

Energy Technology Data Exchange (ETDEWEB)

Alexahin, Y; Gianfelice-Wendt, E, E-mail: alexahin@fnal.gov [Fermi National Accelerator Laboratory, P.O. Box 500, Batavia, Illinois 60510 (United States)

2011-10-15

A method for evaluation of coupled optics functions, detection of strong perturbing elements, determination of BPM calibration errors and tilts using turn-by-turn (TBT) data is presented as well as the new version of the Hamiltonian perturbation theory of betatron oscillations the method is based upon. An example of application of the considered method to the Tevatron is given.

Turn-around improvements

International Nuclear Information System (INIS)

Redaelli, S.; Venturini Delsolaro, W.

2012-01-01

An efficient turn-around will be an important parameter for the integrated luminosity performance at LHC in 2012, when an operation with steady beam parameters and machine configuration will be achieved at the beginning of the run. Improvements of the operational cycle were already put successfully in place after the 2010 experience but additional ways to reduce the time required to setup collisions are possible. In this paper, the 2011 turn-around performance is reviewed and the benefits of the improvements from 2010 are presented. Phases of the operational cycle when further amelioration is possible are discussed and some proposal for a faster turn-around in 2012 are outlined. (authors)

Impacts of proposed RCRA regulations and other related federal environmental regulations on fossil fuel-fired facilities: Final report, Volume 2

Energy Technology Data Exchange (ETDEWEB)

1987-03-01

Estimation of the costs associated with implementation of the Resource Conservation and Recovery Act (RCRA) regulations for non-hazardous and hazardous material disposal in the utility industry are provided. These costs are based on engineering studies at a number of coal-fired power plants in which the costs for hazardous and non-hazardous disposal are compared to the costs developed for the current practice design for each utility. The relationship of the three costs is displayed. The emphasis of this study is on the determination of incremental costs rather than the absolute costs for each case (current practice, non-hazardous, or hazardous). For the purpose of this project, the hazardous design cost was determined for minimum versus maximum compliance.

A sensitivity analysis of hazardous waste disposal site climatic and soil design parameters using HELP3

International Nuclear Information System (INIS)

Adelman, D.D.; Stansbury, J.

1997-01-01

The Resource Conservation and Recovery Act (RCRA) Subtitle C, Comprehensive Environmental Response, Compensation, And Liability Act (CERCLA), and subsequent amendments have formed a comprehensive framework to deal with hazardous wastes on the national level. Key to this waste management is guidance on design (e.g., cover and bottom leachate control systems) of hazardous waste landfills. The objective of this research was to investigate the sensitivity of leachate volume at hazardous waste disposal sites to climatic, soil cover, and vegetative cover (Leaf Area Index) conditions. The computer model HELP3 which has the capability to simulate double bottom liner systems as called for in hazardous waste disposal sites was used in the analysis. HELP3 was used to model 54 combinations of climatic conditions, disposal site soil surface curve numbers, and leaf area index values to investigate how sensitive disposal site leachate volume was to these three variables. Results showed that leachate volume from the bottom double liner system was not sensitive to these parameters. However, the cover liner system leachate volume was quite sensitive to climatic conditions and less sensitive to Leaf Area Index and curve number values. Since humid locations had considerably more cover liner system leachate volume than and locations, different design standards may be appropriate for humid conditions than for and conditions

Turns prediction : Turns prediction

OpenAIRE

Fuchs, Patrick; Etchebest, Catherine; De Brevern, Alexandre

2007-01-01

The description of protein 3D structure usually focuses on the repetitive local folds (alpha-helices and beta-sheets). The remaining class, sometimes called unordered region, has often been considered as random (one also calls it ‘random coil'). However, some interesting local folds are also highly recurrent and definitely more structured than a real random region. One of such particularly interesting motif is tight turn; this latter is characterized by few residues (3 to 5) and by the revers...

Turning nuclear communications inside out

International Nuclear Information System (INIS)

Besenyei, Elisabeth; Czibolya, Laszlo

2002-01-01

Due to debates on the security of energy supply in the European Union, the international efforts on the implementation of Kyoto protocol and the forthcoming liberalization of the electrical energy market the attention of Hungarian decision-makers was focused on energy related problems. Discussions started on the future role of nuclear power and anti-nuclear environmentalists became more active in their criticism. Changes were needed in the approach and practice of communication on nuclear energy. Previous practice turned to be inefficient in dialogue with different social and influential groups. Public information could not be considered any more as an activity explaining measures to cope with incidents and accidents or giving technical answers to mostly superficial statements on allegedly unsafe features and solutions in nuclear industry. It was time to change the paradigm and to turn the communication into a powerful tool to put forward the arguments, to show the achievements and facts and to explain the efforts in addressing public concerns. The new paradigm turned the previous outside-in approach to a new inside-out type of behavior. Instead of reacting to the attacks coming from outside the new approach means first of all commitment to be open and pro-active in communication and to act in close cooperation with all interested organizations and institutions. The three pillars of the new paradigm, commitment, communication and co-operation are applicable not only for the nuclear industry, but also for the governmental agencies (regulatory bodies, health and emergency authorities etc.) and for the wide range of technical, scientific and civil organizations. Public information should be turned from a burden to a challenge for open, technically valid and honest dialogue. This active communication approach is illustrated by some new initiatives in public information in Hungary. Following the successful Nuclear Academy for Journalists formed new Section of Nuclear

Research of remote control system in turn by turn timing system

International Nuclear Information System (INIS)

Zhan Zhifeng; Xiao Yanguo; Ma Kui; Yin Zejie; Wu Xiaoyi

2003-01-01

In this paper, we introduce a remote control system which is used in a frequency dividing and time-delay module. This control system is based on client/server architecture, and RS232 serial communication protocol. This control system is used in timing system of NSRL turn by turn beam position monitor

Phase 2 sampling and analysis plan, Quality Assurance Project Plan, and environmental health and safety plan for the Clinch River Remedial Investigation: An addendum to the Clinch River RCRA Facility Investigation plan

International Nuclear Information System (INIS)

Cook, R.B.; Adams, S.M.; Beauchamp, J.J.; Bevelhimer, M.S.; Blaylock, B.G.; Brandt, C.C.; Etnier, E.L.; Ford, C.J.; Frank, M.L.; Gentry, M.J.; Greeley, M.S.; Halbrook, R.S.; Harris, R.A.; Holladay, S.K.; Hook, L.A.; Howell, P.L.; Kszos, L.A.; Levine, D.A.; Skiles, J.L.; Suter, G.W.

1992-12-01

This document contains a three-part addendum to the Clinch River Resource Conservation and Recovery Act (RCRA) Facility Investigation Plan. The Clinch River RCRA Facility Investigation began in 1989, as part of the comprehensive remediation of facilities on the US Department of Energy Oak Ridge Reservation (ORR). The ORR was added to the National Priorities List in December 1989. The regulatory agencies have encouraged the adoption of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) terminology; therefore, the Clinch River activity is now referred to as the Clinch River Remedial Investigation (CRRI), not the Clinch River RCRA Facility Investigation. Part 1 of this document is the plan for sampling and analysis (S ampersand A) during Phase 2 of the CRRI. Part 2 is a revision of the Quality Assurance Project Plan for the CRRI, and Part 3 is a revision of the Environmental Health and Safety Plan for the CRRI. The Clinch River RI (CRRI) is designed to address the transport, fate, and distribution of waterborne contaminants (radionuclides, metals, and organic compounds) released from the DOE Oak Ridge Reservation (ORR) and to assess potential risks to human health and the environment associated with these contaminants. Primary areas of investigation are Melton Hill Reservoir, the Clinch River from Melton Hill Dam to its confluence with the Tennessee River, Poplar Creek, and Watts Bar Reservoir. The contaminants identified in the Clinch River/Watts Bar Reservoir (CR/WBR) downstream of the ORR are those associated with the water, suspended particles, deposited sediments, aquatic organisms, and wildlife feeding on aquatic organisms. The purpose of the Phase 2 S ampersand A Plan is to describe the proposed tasks and subtasks developed to meet the primary objectives of the CRRI

Phase 2 sampling and analysis plan, Quality Assurance Project Plan, and environmental health and safety plan for the Clinch River Remedial Investigation: An addendum to the Clinch River RCRA Facility Investigation plan

Energy Technology Data Exchange (ETDEWEB)

Cook, R.B.; Adams, S.M.; Beauchamp, J.J.; Bevelhimer, M.S.; Blaylock, B.G.; Brandt, C.C.; Etnier, E.L.; Ford, C.J.; Frank, M.L.; Gentry, M.J.; Greeley, M.S.; Halbrook, R.S.; Harris, R.A.; Holladay, S.K.; Hook, L.A.; Howell, P.L.; Kszos, L.A.; Levine, D.A.; Skiles, J.L.; Suter, G.W.

1992-12-01

This document contains a three-part addendum to the Clinch River Resource Conservation and Recovery Act (RCRA) Facility Investigation Plan. The Clinch River RCRA Facility Investigation began in 1989, as part of the comprehensive remediation of facilities on the US Department of Energy Oak Ridge Reservation (ORR). The ORR was added to the National Priorities List in December 1989. The regulatory agencies have encouraged the adoption of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) terminology; therefore, the Clinch River activity is now referred to as the Clinch River Remedial Investigation (CRRI), not the Clinch River RCRA Facility Investigation. Part 1 of this document is the plan for sampling and analysis (S A) during Phase 2 of the CRRI. Part 2 is a revision of the Quality Assurance Project Plan for the CRRI, and Part 3 is a revision of the Environmental Health and Safety Plan for the CRRI. The Clinch River RI (CRRI) is designed to address the transport, fate, and distribution of waterborne contaminants (radionuclides, metals, and organic compounds) released from the DOE Oak Ridge Reservation (ORR) and to assess potential risks to human health and the environment associated with these contaminants. Primary areas of investigation are Melton Hill Reservoir, the Clinch River from Melton Hill Dam to its confluence with the Tennessee River, Poplar Creek, and Watts Bar Reservoir. The contaminants identified in the Clinch River/Watts Bar Reservoir (CR/WBR) downstream of the ORR are those associated with the water, suspended particles, deposited sediments, aquatic organisms, and wildlife feeding on aquatic organisms. The purpose of the Phase 2 S A Plan is to describe the proposed tasks and subtasks developed to meet the primary objectives of the CRRI.

Application of digital lock-in detection to Hefei Light Source turn-by-turn system

International Nuclear Information System (INIS)

Yang Yongliang; Wang Junhua; Sun Baogen; Chen Yuanbo; Zhou Zeran

2010-01-01

This paper introduces the digital lock-in detection theory and discusses its feasibility to obtain the damping rate in turn-by-turn measurement systems. Numerical simulations of this method were carried out with Matlab. Then principle presenting beam experiments were conducted on the Hefei Light Source (HLS) storage ring. The measured beta oscillation growth time is about 0.26 ms and the damping time is about 1.2 ms. Simulation and experimental results show that, the digital lock-in detection method is effective in damping rate measurement in turn-by-turn measurement systems. (authors)

Turned on/turned off

DEFF Research Database (Denmark)

Petersen, Eva Bendix

2016-01-01

position, it attempts to sense into the lived experience of being subject to, and of, turns in social theory. As a whole the paper seeks to work with and allow for multiplicity in tone, focus, researcher positioning, reader positioning, and more, to see what knowledge that does not seek confident closure......Through cacophonic story-telling, emerging from ethnographic observations from academic scenes in Australia and elsewhere, the article seeks to explore the timeliness and untimeliness of feminist knowledge production. Rather than arguing a particular point or making a claim for a particular...

Immediate Effects of Clock-Turn Strategy on the Pattern and Performance of Narrow Turning in Persons With Parkinson Disease.

Science.gov (United States)

Yang, Wen-Chieh; Hsu, Wei-Li; Wu, Ruey-Meei; Lin, Kwan-Hwa

2016-10-01

Turning difficulty is common in people with Parkinson disease (PD). The clock-turn strategy is a cognitive movement strategy to improve turning performance in people with PD despite its effects are unverified. Therefore, this study aimed to investigate the effects of the clock-turn strategy on the pattern of turning steps, turning performance, and freezing of gait during a narrow turning, and how these effects were influenced by concurrent performance of a cognitive task (dual task). Twenty-five people with PD were randomly assigned to the clock-turn or usual-turn group. Participants performed the Timed Up and Go test with and without concurrent cognitive task during the medication OFF period. The clock-turn group performed the Timed Up and Go test using the clock-turn strategy, whereas participants in the usual-turn group performed in their usual manner. Measurements were taken during the 180° turn of the Timed Up and Go test. The pattern of turning steps was evaluated by step time variability and step time asymmetry. Turning performance was evaluated by turning time and number of turning steps. The number and duration of freezing of gait were calculated by video review. The clock-turn group had lower step time variability and step time asymmetry than the usual-turn group. Furthermore, the clock-turn group turned faster with fewer freezing of gait episodes than the usual-turn group. Dual task increased the step time variability and step time asymmetry in both groups but did not affect turning performance and freezing severity. The clock-turn strategy reduces turning time and freezing of gait during turning, probably by lowering step time variability and asymmetry. Dual task compromises the effects of the clock-turn strategy, suggesting a competition for attentional resources.Video Abstract available for more insights from the authors (see Supplemental Digital Content 1, http://links.lww.com/JNPT/A141).

75 FR 984 - Draft Recommended Interim Preliminary Remediation Goals for Dioxin in Soil at CERCLA and RCRA Sites

Science.gov (United States)

2010-01-07

...The Environmental Protection Agency (EPA or the Agency) is announcing a 50-day public comment period for draft recommended interim preliminary remediation goals (PRGs) developed in the Draft Recommended Interim Preliminary Remediation Goals for Dioxin in Soil at Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and Resource Conservation and Recovery Act (RCRA) Sites. EPA's Office of Solid Waste and Emergency and Emergency Response (OSWER) has developed the draft recommended interim PRGs for dioxin in soil. These draft recommended interim PRGs were calculated using existing, peer- reviewed toxicity values and current EPA equations and default exposure assumptions. This Federal Register notice is intended to provide an opportunity for public comment on the draft recommended interim PRGs. EPA will consider any public comments submitted in accordance with this notice and may revise the draft recommended interim PRGs thereafter.

Phase 1 RCRA Facility Investigation/Corrective Measures Study Work Plan for Single-Shell Tank (SST) Waste Management Areas

International Nuclear Information System (INIS)

MCCARTHY, M.M.

1999-01-01

This document is the master work plan for the Resource Conservation and Recovery Act of 1976 (RCRA) Corrective Action Program (RCAP) for single-shell tank (SST) farms at the US. Department of Energy's (DOE'S) Hanford Site. The DOE Office of River Protection (ORP) initiated the RCAP to address the impacts of past and potential future tank waste releases to the environment. This work plan defines RCAP activities for the four SST waste management areas (WMAs) at which releases have contaminated groundwater. Recognizing the potential need for future RCAP activities beyond those specified in this master work plan, DOE has designated the currently planned activities as ''Phase 1.'' If a second phase of activities is needed for the WMAs addressed in Phase 1, or if releases are detected at other SST WMAs, this master work plan will be updated accordingly

Financial responsibilities under RCRA. Hearing before the Subcommittee on Commerce, Transportation, and Tourism of the Committee on Energy and Commerce, House of Representatives, Ninety-Ninth Congress, First Session on H. R. 3692, November 13, 1985

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

Representatives of environmental organizations, the Hazardous Waste Treatment Council, and regulators were among those testifying at a hearing on H.R. 3692, which amends the Resource Conservation and Recovery Act (RCRA) of 1976. The bill is in response to concerns that the Environmental Protection Agency (EPA) has not compiled with the intent of RCRA in its failure to move beyond interim permits to issue final permits to land disposal facilities accepting hazardous wastes. Reported leakage and environmental risks from sites operating under interim permits raises questions about how disposal companies could deal with liability claims. At issue was whether Congress needs to take new action to develop regulations under which financially responsible companies can operate or whether new EPA rules can solve the problem. A spokesman for EPA reviewed the liability insurance problem and the status of the insurance market in this context. Material submitted for the record follows the text of H.R. 3692 and the testimony of 11 witnesses.

Salt-bridging effects on short amphiphilic helical structure and introducing sequence-based short beta-turn motifs.

Science.gov (United States)

Guarracino, Danielle A; Gentile, Kayla; Grossman, Alec; Li, Evan; Refai, Nader; Mohnot, Joy; King, Daniel

2018-02-01

Determining the minimal sequence necessary to induce protein folding is beneficial in understanding the role of protein-protein interactions in biological systems, as their three-dimensional structures often dictate their activity. Proteins are generally comprised of discrete secondary structures, from α-helices to β-turns and larger β-sheets, each of which is influenced by its primary structure. Manipulating the sequence of short, moderately helical peptides can help elucidate the influences on folding. We created two new scaffolds based on a modestly helical eight-residue peptide, PT3, we previously published. Using circular dichroism (CD) spectroscopy and changing the possible salt-bridging residues to new combinations of Lys, Arg, Glu, and Asp, we found that our most helical improvements came from the Arg-Glu combination, whereas the Lys-Asp was not significantly different from the Lys-Glu of the parent scaffold, PT3. The marked 3 10 -helical contributions in PT3 were lessened in the Arg-Glu-containing peptide with the beginning of cooperative unfolding seen through a thermal denaturation. However, a unique and unexpected signature was seen for the denaturation of the Lys-Asp peptide which could help elucidate the stages of folding between the 3 10 and α-helix. In addition, we developed a short six-residue peptide with β-turn/sheet CD signature, again to help study minimal sequences needed for folding. Overall, the results indicate that improvements made to short peptide scaffolds by fine-tuning the salt-bridging residues can enhance scaffold structure. Likewise, with the results from the new, short β-turn motif, these can help impact future peptidomimetic designs in creating biologically useful, short, structured β-sheet-forming peptides.

Predictors and use of nonpharmacologic interventions for procedural pain associated with turning among hospitalized adults.

Science.gov (United States)

Faigeles, Bonnie; Howie-Esquivel, Jill; Miaskowski, Christine; Stanik-Hutt, Julie; Thompson, Carol; White, Cheri; Wild, Lorie Rietman; Puntillo, Kathleen

2013-06-01

Many hospitalized adults cannot reposition themselves in their beds. Therefore, they are regularly turned by their nurses, primarily to prevent pressure ulcer formation. Earlier research indicates that turning is painful and that patients are rarely premedicated with analgesics. Nonpharmacologic interventions may be used to help with this painful procedure. However, no published research was found on the use of nonpharmacologic interventions for turning of hospitalized patients. The objectives of this study were: 1) to describe patient pain characteristics during turning and their association with patient demographic and clinical characteristics; 2) to determine the frequency of use of various nonpharmacologic interventions for hospitalized adult patients undergoing the painful procedure of turning; and 3) to identify factors that predict the use of specific nonpharmacologic interventions for pain associated with turning. Hospitalized adult patients who experienced turning, the nurses caring for them, and others who were present at the time of turning were asked if they used various nonpharmacologic interventions to manage pain during the turning. Out of 1,395 patients, 92.5% received at least one nonpharmacologic intervention. Most frequently used were calming voice (65.7%), information (60.6%), and deep breathing (37.9%). Critical-care patients were more likely to receive a calming voice (odds ratio [OR] 1.66, p patients. Those reporting higher pain were consistently more likely to receive each of the three interventions (OR 1.01, p turning procedure. The specific interventions used most often are ones that can be initiated spontaneously. Our data suggest that patients, nurses, and family members respond to patients' turning-related pain by using nonpharmacologic interventions. Copyright © 2013 American Society for Pain Management Nursing. Published by Elsevier Inc. All rights reserved.

Pilot study: Assessing the effect of continual position monitoring technology on compliance with patient turning protocols.

Science.gov (United States)

Schutt, Suann Cirigliano; Tarver, Christine; Pezzani, Michelle

2018-01-01

The study aim was to evaluate if continual patient position monitoring, taking into account self-turns and clinician-assisted turns, would increase the percentage of time a patient's position changed at least every 2 hr. While patient turning has clinical benefits, current models to help staff remember to turn patients, such as "turn clocks" and timers, have not resulted in high compliance with turning protocols. In addition, reminders are based on arbitrary 2-hr windows (such as turning on "even" hours) rather than on individual patient activity, including self-turns. This is a first inpatient, non-randomized, pre-/postintervention study. Data collection occurred from May 2013-February 2014 on a 39-bed medical unit in a community hospital. Baseline patient turning data were recorded by a sensor; however, the patient data were not displayed at the nurses' station to establish compliance with the hospital's turning protocol. Postintervention, patient position information was wirelessly displayed on nurses' station computer monitors in real time. A Student t test was used to compare baseline to postintervention "mean time in compliance." Data from 138 patients ( N  =   7,854 hr of monitoring) were collected. The baseline phase yielded 4,322 hr of position monitoring data and the postintervention phase yielded 3,532 hr of data. Statistically significant improvement was demonstrated in the percentage of time a patient's position changed at least every 2 hr from baseline to postintervention.

Turning Schools Inside Out: Connecting Schools and Communities through Public Arts and Literacies

Science.gov (United States)

Charest, Brian C.; Bell, Lauren D.; Gonzalez, Marialuisa; Parker, Veronica L.

2014-01-01

In this paper we tell a story about how we partnered with a Chicago high school in order to turn the school inside out by displaying larger-than-life teacher portraits and statements at street level throughout the community. This paper explores how public art and activism can help teachers and students develop notions of civic literacy and…

RCRA Facility Investigation/Remedial Investigation Report for Gunsite 720 Rubble Pit Unit (631-16G) - March 1996

Energy Technology Data Exchange (ETDEWEB)

Palmer, E. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1996-03-01

Gunsite 720 Rubble Pit Unit is located on the west side of SRS. In the early to mid 1980`s, while work was being performed in this area, nine empty, partially buried drums, labeled `du Pont Freon 11`, were found. As a result, Gunsite 720 became one of the original waste units specified in the SRS RCRA Facility Assessment (RFA). The drums were excavated on July 30, 1987 and placed on a pallet at the unit. Both the drums and pallet were removed and disposed of in October 1989. The area around the drums was screened during the excavation and the liquid (rainwater) that collected in the excavated drums was sampled prior to disposal. No evidence of hazardous materials was found. Based on the review of the analytical data and screening techniques used to evaluate all the chemicals of potential concern at Gunsite 720 Rubble Pit Unit, it is recommended that no further remedial action be performed at this unit.

RCRA Facility Investigation/Remedial Investigation Report for Gunsite 720 Rubble Pit Unit (631-16G) - March 1996

International Nuclear Information System (INIS)

Palmer, E.

1996-03-01

Gunsite 720 Rubble Pit Unit is located on the west side of SRS. In the early to mid 1980's, while work was being performed in this area, nine empty, partially buried drums, labeled 'du Pont Freon 11', were found. As a result, Gunsite 720 became one of the original waste units specified in the SRS RCRA Facility Assessment (RFA). The drums were excavated on July 30, 1987 and placed on a pallet at the unit. Both the drums and pallet were removed and disposed of in October 1989. The area around the drums was screened during the excavation and the liquid (rainwater) that collected in the excavated drums was sampled prior to disposal. No evidence of hazardous materials was found. Based on the review of the analytical data and screening techniques used to evaluate all the chemicals of potential concern at Gunsite 720 Rubble Pit Unit, it is recommended that no further remedial action be performed at this unit

Infrared thermography based diagnosis of inter-turn fault and cooling system failure in three phase induction motor

Science.gov (United States)

Singh, Gurmeet; Naikan, V. N. A.

2017-12-01

Thermography has been widely used as a technique for anomaly detection in induction motors. International Electrical Testing Association (NETA) proposed guidelines for thermographic inspection of electrical systems and rotating equipment. These guidelines help in anomaly detection and estimating its severity. However, it focus only on location of hotspot rather than diagnosing the fault. This paper addresses two such faults i.e. inter-turn fault and failure of cooling system, where both results in increase of stator temperature. Present paper proposes two thermal profile indicators using thermal analysis of IRT images. These indicators are in compliance with NETA standard. These indicators help in correctly diagnosing inter-turn fault and failure of cooling system. The work has been experimentally validated for healthy and with seeded faults scenarios of induction motors.

Turn-by-Turn and Bunch-by-Bunch Transverse Profiles of a Single Bunch in a Full Ring

International Nuclear Information System (INIS)

Kraus, R.; Fisher, A.S.

2005-01-01

The apparatus described in this paper can image the evolution of the transverse profile of a single bunch, isolated from a full PEP-II ring of 1500 bunches. Using this apparatus there are two methods of single bunch imaging; bunch-by-bunch beam profiling can image every bunch in the ring a single bunch at a time with the images of sequential bunches being in order, allowing one to see variations in beam size along a train. Turn-by-turn beam profiling images a single bunch on each successive turn it makes around the ring. This method will be useful in determining the effect that an injected bunch has on a stable bunch as the oscillations of the injected bunch damp out. Turn-by-turn imaging of the synchrotron light uses a system of lenses and mirrors to image many turns of both the major and minor axis of a single bunch across the photocathode of a gateable camera. The bunch-by-bunch method is simpler: because of a focusing mirror used in porting the light from the ring, the synchrotron light from the orbiting electrons becomes an image at a certain distance from the mirror; and since the camera does not use a lens, the photocathode is set exactly at this image distance. Bunch-by-bunch profiling has shown that in the Low Energy Ring (LER) horizontal bunch size decreases along a train. Turn-by-turn profiling has been able to image 100 turns of a single bunch on one exposure of the camera. The turn-by-turn setup has also been able to image 50 turns of the minor axis showing part of the damping process of an oscillating injected charge during a LER fill. The goal is to image the damping of oscillations of injected charge for 100 turns of both the major and minor axis throughout the damping process during trickle injection. With some changes to the apparatus this goal is within reach and will make turn-by-turn imaging a very useful tool in beam diagnostics

Study on the machinability characteristics of superalloy Inconel 718 during high speed turning

International Nuclear Information System (INIS)

Thakur, D.G.; Ramamoorthy, B.; Vijayaraghavan, L.

2009-01-01

The present paper is an attempt of an experimental investigation on the machinability of superalloy, Inconel 718 during high speed turning using tungsten carbide insert (K20) tool. The effect of machining parameters on the cutting force, specific cutting pressure, cutting temperature, tool wear and surface finish criteria were investigated during the experimentation. The machining parameters have been optimized by measuring forces. The effect of machining parameters on the tool wear was examined through SEM micrographs. During high speed turning acoustic emission signal were collected and analyzed to understand the effect of cutting parameters during online. The research work findings will also provide useful economic machining solution by utilizing economical tungsten carbide tooling during high speed processing of Inconel 718, which is otherwise usually machined by costly PCD or CBN tools. The present approach and results will be helpful for understanding the machinability of Inconel 718 during high speed turning for the manufacturing engineers

Help-Seeking on Facebook Versus More Traditional Sources of Help: Cross-Sectional Survey of Military Veterans.

Science.gov (United States)

Teo, Alan R; Marsh, Heather E; Liebow, Samuel B L; Chen, Jason I; Forsberg, Christopher W; Nicolaidis, Christina; Saha, Somnath; Dobscha, Steven K

2018-02-26

The media has devoted significant attention to anecdotes of individuals who post messages on Facebook prior to suicide. However, it is unclear to what extent social media is perceived as a source of help or how it compares to other sources of potential support for mental health problems. This study aimed to evaluate the degree to which military veterans with depression use social media for help-seeking in comparison to other more traditional sources of help. Cross-sectional self-report survey of 270 adult military veterans with probable major depression. Help-seeking intentions were measured with a modified General Help-Seeking Questionnaire. Facebook users and nonusers were compared via t tests, Chi-square, and mixed effects regression models. Associations between types of help-seeking were examined using mixed effects models. The majority of participants were users of social media, primarily Facebook (n=162). Mean overall help-seeking intentions were similar between Facebook users and nonusers, even after adjustment for potential confounders. Facebook users were very unlikely to turn to Facebook as a venue for support when experiencing either emotional problems or suicidal thoughts. Compared to help-seeking intentions for Facebook, help-seeking intentions for formal (eg, psychologists), informal (eg, friends), or phone helpline sources of support were significantly higher. Results did not substantially change when examining users of other social media, women, or younger adults. In its current form, the social media platform Facebook is not seen as a venue to seek help for emotional problems or suicidality among veterans with major depression in the United States. ©Alan R Teo, Heather E Marsh, Samuel B L Liebow, Jason I Chen, Christopher W Forsberg, Christina Nicolaidis, Somnath Saha, Steven K Dobscha. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 26.02.2018.

Helping organizations help others: organization development as a facilitator of social change.

Science.gov (United States)

Boyd, Neil M

2011-01-01

This article explores organization development (OD) interventions and their likelihood of increasing social change outcomes in public agencies. The central argument of this work is that public and nonprofit organizations can deliver better social outcomes by systematically engaging in OD interventions. An in-depth survey was conducted in 3 agencies of the Commonwealth of Pennsylvania at the end of the gubernatorial administration of Tom Ridge (1995-2002). During his administration, Governor Ridge led the agencies of Pennsylvania government through a large-scale change effort to improve the efficiency and effectiveness of service delivery to the citizens of the Commonwealth of Pennsylvania. The change effort was a remarkable event for the Commonwealth because no other governor in the history of the state had attempted to conceptualize and deliver a comprehensive large-scale change management initiative. The successes and setbacks served as a fertile context to shed light on the following research question: Do OD interventions increase the likelihood that public organizations will deliver better social outcomes? This question is important in that public organizations may need to engage in organization development activities to improve their internal operations, which in turn may help them provide exemplary social outcomes to those whom they serve. In short, organization development interventions might allow public organizations to help themselves to help others.

Beam Optics Measurements Through Turn by Turn Beam Position Data in the SLS

CERN Document Server

Zisopoulos, P; Streun, A; Ziemann, v

2013-01-01

Refined Fourier analysis of turn-by-turn (TBT) transverse position data measurements can be used for determining several beam properties of a ring, such as transverse tunes, optics functions, phases, chromatic properties and coupling. In particular, the Numerical Analysis of Fundamental Frequencies (NAFF) algorithm is used to analyse TBT data from the Swiss Light Source (SLS) storage ring in order to estimate on and off-momentum beam characteristics. Of particular interest is the potential of using the full position information within one turn in order to measure beam optics properties.

Realistic page-turning of electronic books

Science.gov (United States)

Fan, Chaoran; Li, Haisheng; Bai, Yannan

2014-01-01

The booming electronic books (e-books), as an extension to the paper book, are popular with readers. Recently, many efforts are put into the realistic page-turning simulation o f e-book to improve its reading experience. This paper presents a new 3D page-turning simulation approach, which employs piecewise time-dependent cylindrical surfaces to describe the turning page and constructs smooth transition method between time-dependent cylinders. The page-turning animation is produced by sequentially mapping the turning page into the cylinders with different radii and positions. Compared to the previous approaches, our method is able to imitate various effects efficiently and obtains more natural animation of turning page.

Molten salt oxidation of mixed wastes: Separation of radioactive materials and Resource Conservation and Recovery Act (RCRA) materials

International Nuclear Information System (INIS)

Bell, J.T.; Haas, P.A.; Rudolph, J.C.

1993-01-01

The Oak Ridge National Laboratory (ORNL) is involved in a program to apply a molten salt oxidation (MSO) process to the treatment of mixed wastes at Oak Ridge and other Department of Energy (DOE) sites. Mixed wastes are defined as those wastes that contain both radioactive components, which are regulated by the atomic energy legislation, and hazardous waste components, which are regulated under the Resource Conservation and Recovery Act (RCRA). A major part of our ORNL program involves the development of separation technologies that are necessary for the complete treatment of mixed wastes. The residues from the MSO treatment of the mixed wastes must be processed further to separate the radioactive components, to concentrate and recycle residues, or to convert the residues into forms acceptable for final disposal. This paper is a review of the MSO requirements for separation technologies, the information now available, and the concepts for our development studies

Phase 1 RCRA Facility Investigation & Corrective Measures Study Work Plan for Single Shell Tank (SST) Waste Management Areas

Energy Technology Data Exchange (ETDEWEB)

MCCARTHY, M.M.

1999-08-01

This document is the master work plan for the Resource Conservation and Recovery Act of 1976 (RCRA) Corrective Action Program (RCAP) for single-shell tank (SST) farms at the US. Department of Energy's (DOE'S) Hanford Site. The DOE Office of River Protection (ORP) initiated the RCAP to address the impacts of past and potential future tank waste releases to the environment. This work plan defines RCAP activities for the four SST waste management areas (WMAs) at which releases have contaminated groundwater. Recognizing the potential need for future RCAP activities beyond those specified in this master work plan, DOE has designated the currently planned activities as ''Phase 1.'' If a second phase of activities is needed for the WMAs addressed in Phase 1, or if releases are detected at other SST WMAs, this master work plan will be updated accordingly.

Hummingbirds control turning velocity using body orientation and turning radius using asymmetrical wingbeat kinematics.

Science.gov (United States)

Read, Tyson J G; Segre, Paolo S; Middleton, Kevin M; Altshuler, Douglas L

2016-03-01

Turning in flight requires reorientation of force, which birds, bats and insects accomplish either by shifting body position and total force in concert or by using left-right asymmetries in wingbeat kinematics. Although both mechanisms have been observed in multiple species, it is currently unknown how each is used to control changes in trajectory. We addressed this problem by measuring body and wingbeat kinematics as hummingbirds tracked a revolving feeder, and estimating aerodynamic forces using a quasi-steady model. During arcing turns, hummingbirds symmetrically banked the stroke plane of both wings, and the body, into turns, supporting a body-dependent mechanism. However, several wingbeat asymmetries were present during turning, including a higher and flatter outer wingtip path and a lower more deviated inner wingtip path. A quasi-steady analysis of arcing turns performed with different trajectories revealed that changes in radius were associated with asymmetrical kinematics and forces, and changes in velocity were associated with symmetrical kinematics and forces. Collectively, our results indicate that both body-dependent and -independent force orientation mechanisms are available to hummingbirds, and that these kinematic strategies are used to meet the separate aerodynamic challenges posed by changes in velocity and turning radius. © 2016 The Author(s).

Learning turning points--in life with long-term illness--visualized with the help of the life-world philosophy.

Science.gov (United States)

Berglund, Mia M U

2014-01-01

A long-term illness is an occurrence that changes one's life and generates a need to learn how to live with it. This article is based on an empirical study of interviews on people living with different long-term illnesses. The results have shown that the learning process is a complex phenomenon interwoven with life as a whole. The essential meaning of learning to live with long-term illness concerns a movement toward a change of understanding of access to the world. In this movement, in which everyday lives as well as relationships with oneself and others are affected, a continual renegotiation is needed. Texts from existential/lifeworld philosopher, Heidegger and Gadamer, have been used to get a greater understanding of the empirical results. These texts have been analysed with particular focus on learning turning points and the importance of reflection. The results are highlighted under the following themes: Pursuit of balance-the aim of learning, The tense grip-the resistance to learning, To live more really-the possibilities of the learning, Distancing-the how of the learning, and The tense of the learning-the whole of the learning. In those learning turning points are present. Knowledge from this study has been used to make a didactic model designed to give caregivers a tool to support patients' learning. The didactic model is called: The challenge to take charge of life with a long-term illness.

CONNECTION OF TURN AHEAD AND TURN BACK WITH MOTORIC ABILITIES OF THE FIFTH GRADE STUDENTS

Directory of Open Access Journals (Sweden)

Jovica Petković

2006-06-01

Full Text Available The research is done for the purpose of determination and defining of the level of connection between some motoric abilities with success in realization of programmed contents from the area of gymnastics (turn ahead and turn back. The research is done on the sample of fifty one students from the fifth grade of Elementary School, on ten motoric tests and on two specific motoric assignments – turn ahead and turn back. The results of this research clearly point that there exist the multitude of statistically important coefficients of correlation between treated motoric abilities and applied motoric assignments.

The embodied turn in research on language and social interaction

DEFF Research Database (Denmark)

Nevile, Maurice

2015-01-01

I use the term the embodied turn to mean the point when interest in the body became established among researchers on language and social interaction, exploiting the greater ease of video-recording. This review paper tracks the growth of "embodiment" in over 400 papers published in Research...... on Language and Social Interaction from 1987-2013. I consider closely two areas where analysts have confronted challenges, and how they have responded: settling on precise and analytically helpful terminology for the body; and transcribing and representing the body, particularly its temporality and manner....

CERN PS Optical Properties Measured with Turn-By-Turn Orbit Data

CERN Document Server

Bach, T; Giovannozzi, M; Hernalsteens, C; Lachaize, A; Sterbini, G; Tom´as, R; Wasef, R

2013-01-01

The performance of the CERN Proton Synchrotron (PS) has been constantly increasing over the years both in terms of beam parameters (intensity and brightness) and beam manipulations (transverse and longitudinal splitting). This implies a very good knowledge of the linear and non-linear model of the ring. In this paper we report on a detailed campaign of beam measurements based on turn-by-turn orbit data aimed at measuring the optics in several conditions as well as the resonance driving terms.

Safety effects of traffic signing for left turn flashing yellow arrow signals.

Science.gov (United States)

Schattler, Kerrie L; Gulla, Cody J; Wallenfang, Travis J; Burdett, Beau A; Lund, Jessica A

2015-02-01

In 2010, the left turn flashing yellow arrow (FYA) signal displays were installed at signalized intersections on state routes in the Peoria, Illinois, area. Supplemental traffic signs with text "Left Turn Yield on Flashing Yellow Arrow" were mounted on the mast arm adjacent to the left turn signal at over half of the FYA installations. The purpose of this paper is to present the results of the effectiveness evaluation of the FYA supplemental sign on safety. Analyses are presented on the effects of the FYA supplemental sign for all drivers and a subset of drivers age 65 and older. A crash-based comparison of 164 FYA approaches including 90 approaches with the sign and 74 approaches without the sign showed greater crash reductions when the supplemental FYA sign was present. The results also showed that crashes involving drivers age 65 and older did not experience the same magnitudes of crash reductions as compared to all drivers. The findings of this research indicate that supplemental FYA signs may help in improving safety for left-turning vehicles during the permissive interval. Thus, it is recommended that supplemental signs be used when initially implementing the FYA, and that effort to educate the driving public on new traffic control be made to further improve safety at signalized intersections. Copyright © 2014. Published by Elsevier Ltd.

Sandstone Turning by Abrasive Waterjet

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

2015-01-01

Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

NetTurnP--neural network prediction of beta-turns by use of evolutionary information and predicted protein sequence features.

Directory of Open Access Journals (Sweden)

Bent Petersen

Full Text Available UNLABELLED: β-turns are the most common type of non-repetitive structures, and constitute on average 25% of the amino acids in proteins. The formation of β-turns plays an important role in protein folding, protein stability and molecular recognition processes. In this work we present the neural network method NetTurnP, for prediction of two-class β-turns and prediction of the individual β-turn types, by use of evolutionary information and predicted protein sequence features. It has been evaluated against a commonly used dataset BT426, and achieves a Matthews correlation coefficient of 0.50, which is the highest reported performance on a two-class prediction of β-turn and not-β-turn. Furthermore NetTurnP shows improved performance on some of the specific β-turn types. In the present work, neural network methods have been trained to predict β-turn or not and individual β-turn types from the primary amino acid sequence. The individual β-turn types I, I', II, II', VIII, VIa1, VIa2, VIba and IV have been predicted based on classifications by PROMOTIF, and the two-class prediction of β-turn or not is a superset comprised of all β-turn types. The performance is evaluated using a golden set of non-homologous sequences known as BT426. Our two-class prediction method achieves a performance of: MCC=0.50, Qtotal=82.1%, sensitivity=75.6%, PPV=68.8% and AUC=0.864. We have compared our performance to eleven other prediction methods that obtain Matthews correlation coefficients in the range of 0.17-0.47. For the type specific β-turn predictions, only type I and II can be predicted with reasonable Matthews correlation coefficients, where we obtain performance values of 0.36 and 0.31, respectively. CONCLUSION: The NetTurnP method has been implemented as a webserver, which is freely available at http://www.cbs.dtu.dk/services/NetTurnP/. NetTurnP is the only available webserver that allows submission of multiple sequences.

NetTurnP--neural network prediction of beta-turns by use of evolutionary information and predicted protein sequence features.

Science.gov (United States)

Petersen, Bent; Lundegaard, Claus; Petersen, Thomas Nordahl

2010-11-30

β-turns are the most common type of non-repetitive structures, and constitute on average 25% of the amino acids in proteins. The formation of β-turns plays an important role in protein folding, protein stability and molecular recognition processes. In this work we present the neural network method NetTurnP, for prediction of two-class β-turns and prediction of the individual β-turn types, by use of evolutionary information and predicted protein sequence features. It has been evaluated against a commonly used dataset BT426, and achieves a Matthews correlation coefficient of 0.50, which is the highest reported performance on a two-class prediction of β-turn and not-β-turn. Furthermore NetTurnP shows improved performance on some of the specific β-turn types. In the present work, neural network methods have been trained to predict β-turn or not and individual β-turn types from the primary amino acid sequence. The individual β-turn types I, I', II, II', VIII, VIa1, VIa2, VIba and IV have been predicted based on classifications by PROMOTIF, and the two-class prediction of β-turn or not is a superset comprised of all β-turn types. The performance is evaluated using a golden set of non-homologous sequences known as BT426. Our two-class prediction method achieves a performance of: MCC=0.50, Qtotal=82.1%, sensitivity=75.6%, PPV=68.8% and AUC=0.864. We have compared our performance to eleven other prediction methods that obtain Matthews correlation coefficients in the range of 0.17-0.47. For the type specific β-turn predictions, only type I and II can be predicted with reasonable Matthews correlation coefficients, where we obtain performance values of 0.36 and 0.31, respectively. The NetTurnP method has been implemented as a webserver, which is freely available at http://www.cbs.dtu.dk/services/NetTurnP/. NetTurnP is the only available webserver that allows submission of multiple sequences.

Self-help groups and mental health/substance use agencies: the benefits of organizational exchange.

Science.gov (United States)

Powell, Thomas; Perron, Brian Edward

2010-02-01

Self-help groups benefit clients by linking them to people who have "been there" and are successfully coping with their situations. Mental health/substance use agencies can increase access to evidence-based benefits of self-help groups by engaging them in organizational exchanges. Organizational theories are used to frame beneficial exchanges with self-help groups. Adaptational theory is used to frame exchanges with self-help groups and various service agency subunits, e.g., board, practitioner, and client units. Institutional theory is used to frame joint agency/self-help initiatives to promote community acceptance of self-help groups, which in turn may enhance the credibility of the professional agency.

and γγ-turns in proteins revisited: A new set of amino acid turn-type de

Indian Academy of Sciences (India)

mine, valine, glutamic acid and alanine has decreased for β-turns. Certain new amino acid preferences were observed for both turn types and individual amino acids showed turn-type dependent positional preferences. The rationale for new amino acid preferences are discussed in the light of hydrogen bonds and other.

Predictors and use of non-pharmacologic interventions for procedural pain associated with turning among hospitalized adults

Science.gov (United States)

Faigeles, Bonnie; Howie-Esquivel, Jill; Miaskowski, Christine; Stanik - Hutt, Julie; Thompson, Carol; White, Cheri; Wild, Lorie Rietman; Puntillo, Kathleen

2010-01-01

Background Many hospitalized adults cannot reposition themselves in their beds. Therefore, they are regularly turned by their nurses, primarily to prevent pressure ulcer formation. Previous research indicates that turning is painful and that patients are rarely pre-medicated with analgesics. Non-pharmacologic interventions may be used to help with this painful procedure. However, no published research was found on the use of non-pharmacologic interventions for turning of hospitalized patients. Objectives 1) to describe patient pain characteristics during turning and their association with patient demographic and clinical characteristics; 2) to determine the frequency of use of various non-pharmacologic interventions for hospitalized adult patients undergoing the painful procedure of turning; and 3) to identify factors that predict the use of specific non-pharmacologic interventions for pain associated with turning. Methods Hospitalized adult patients who experienced turning, the nurses caring for them, and others who were present at the time of turning were asked if they used various non-pharmacologic interventions to manage pain during the turning. Results Of 1395 patients, 92.5% received at least one non-pharmacologic intervention. Most frequently used were calming voice (65.7%), information (60.6%), and deep breathing (37.9%). Critical care patients were more likely to receive a calming voice (OR= 1.66, ppatients. Those reporting higher pain were consistently more likely to receive each of the three interventions (OR=1.01, pturning procedure. The specific interventions used most often are ones that can be initiated spontaneously. These data suggest that patients, nurses, and family members respond to patients’ turning-related pain by using non-pharmacologic interventions. PMID:23688362

The elimination of chlorinated, chlorofluorocarbon, and other RCRA hazardous solvents from the Y-12 Plant's enriched uranium operations

International Nuclear Information System (INIS)

Johnson, D.H.; Patton, R.L.; Thompson, L.M.

1990-01-01

A major driving force in waste minimization within the plant is the reduction of mixed radioactive wastes associated with operations on highly enriched uranium. High enriched uranium has a high concentration of the uranium-235 isotope (up to 97.5% enrichment) and is radioactive, giving off alpha and low level gamma radiation. The material is fissionable with as little as two pounds dissolved in water being capable of producing a spontaneous chain reaction. For these reasons the material is processed in small batches or small geometries. Additionally, the material is completely recycled because of its strategic and monetary value. Since the early eighties, the plant has had an active waste minimization program which has concentrated on substitution of less hazardous solvents wherever possible. The following paper summarizes efforts in two areas - development of a water-based machining coolant to replace perchloroethylene and substitution of an aliphatic solvent to replace solvents producing hazardous wastes as defined by the Resource, Conservation, and Recovery Act (RCRA)

Contaminant fluxes through site containment barriers: Performance assessment and illustrative results

International Nuclear Information System (INIS)

Vita, C.L.

1994-01-01

Contaminant mass flux by advective and diffusive transport is predicted for five containment barriers that use one or more clay liners, flexible membrane liners (FMLs), or liquid collection and removal systems (LCRS)s. Barriers are engineered systems intended to contain and isolate site contaminants from the environment. Barriers include liners, caps, and cutoff walls. Barriers may be used in contaminated-site cleanups (including CERCLA and RCRA), RCRA landfills, or other RCRA TSDFs. Concepts are provided for barrier performance assessment, including analysis and optimization, for meeting performance requirements and controlling risk at minimum cost. Concepts and results can help in planning, designing, or evaluating and communicating, the use or effectiveness of proposed or existing barriers for site cleanups or waste containment. 15 refs., 6 figs., 5 tabs

Beta-and gamma-turns in proteins revisited: a new set of amino acid turn-type dependent positional preferences and potentials.

Science.gov (United States)

Guruprasad, K; Rajkumar, S

2000-06-01

The number of beta-turns in a representative set of 426 protein three-dimensional crystal structures selected from the recent Protein Data Bank has nearly doubled and the number of gamma-turns in a representative set of 320 proteins has increased over seven times since the previous analysis. Beta-turns (7153) and gamma-turns (911) extracted from these proteins were used to derive a revised set of type-dependent amino acid positional preferences and potentials. Compared with previous results, the preference for proline, methionine and tryptophan has increased and the preference for glutamine, valine, glutamic acid and alanine has decreased for beta-turns. Certain new amino acid preferences were observed for both turn types and individual amino acids showed turn-type dependent positional preferences. The rationale for new amino acid preferences are discussed in the light of hydrogen bonds and other interactions involving the turns. Where main-chain hydrogen bonds of the type NH(i + 3) --> CO(i) were not observed for some beta-turns, other main-chain hydrogen bonds or solvent interactions were observed that possibly stabilize such beta-turns. A number of unexpected isolated beta-turns with proline at i + 2 position were also observed. The NH(i + 2) --> CO(i) hydrogen bond was observed for almost all gamma-turns. Nearly 20% classic gamma-turns and 43% inverse gamma-turns are isolated turns.

RCRA Facility investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 5, Technical Memorandums 06-09A, 06-10A, and 06-12A

Energy Technology Data Exchange (ETDEWEB)

None

1991-09-01

This report provides a detailed summary of the activities carried out to sample groundwater at Waste Area Grouping (WAG) 6. The analytical results for samples collected during Phase 1, Activity 2 of the WAG 6 Resource Conservation and Recovery Act Facility Investigation (RFI) are also presented. In addition, analytical results for Phase 1, activity sampling events for which data were not previously reported are included in this TM. A summary of the groundwater sampling activities of WAG 6, to date, are given in the Introduction. The Methodology section describes the sampling procedures and analytical parameters. Six attachments are included. Attachments 1 and 2 provide analytical results for selected RFI groundwater samples and ORNL sampling event. Attachment 3 provides a summary of the contaminants detected in each well sampled for all sampling events conducted at WAG 6. Bechtel National Inc. (BNI)/IT Corporation Contract Laboratory (IT) RFI analytical methods and detection limits are given in Attachment 4. Attachment 5 provides the Oak Ridge National Laboratory (ORNL)/Analytical Chemistry Division (ACD) analytical methods and detection limits and Resource Conservation and Recovery Act (RCRA) quarterly compliance monitoring (1988--1989). Attachment 6 provides ORNL/ACD groundwater analytical methods and detection limits (for the 1990 RCRA semi-annual compliance monitoring).

Turn-by-Turn Imaging of the Transverse Beam Profile in PEP-II

Energy Technology Data Exchange (ETDEWEB)

Fisher, Alan A.; Petree, Mark; /SLAC

2006-12-18

During injection or instability, the transverse profile of an individual bunch in a storage ring can change significantly in a few turns. However, most synchrotron-light imaging techniques are not designed for this time scale. We have developed a novel diagnostic that enhances the utility of a fast gated camera by adding, inexpensively, some features of a dual-axis streak camera, in order to watch the turn-by-turn evolution of the transverse profile, in both x and y. The beam's elliptical profile is reshaped using cylindrical lenses to form a tall and narrow ellipse--essentially the projection of the full ellipse onto one transverse axis. We do this projection twice, by splitting the beam into two paths at different heights, and rotating the ellipse by 90{sup o} on one path. A rapidly rotating mirror scans these vertical ''pencils'' of light horizontally across the photocathode of the camera, which is gated for 3 ns on every Nth ring turn. A single readout of the camera captures 100 images, looking like a stroboscopic photograph of a moving object. We have observed the capture of injected charge into a bunch and the rapid change of beam size at the onset of a fast instability.

Clinical evaluation of an automated turning bed.

Science.gov (United States)

Melland, H I; Langemo, D; Hanson, D; Olson, B; Hunter, S

1999-01-01

The purposes of this study were to assess client comfort and sleep quality, client physiologic response (skin and respiratory status), the effect on the need for caregiver assistance, and cost when using an automated turning bed. Nonexperimental, evaluative study. Twenty-four adult home or long-term care resident subjects who had a degenerative disease, spinal cord injury, stroke, cerebral palsy, or back surgery. Each subject agreed to use the automated turning bed for four weeks. Researchers completed a demographic survey and skin assessment, and assessed each subject for pressure ulcer risk and for the need of assistance of a care giver for turning before and after the four weeks of using the turning bed. Subjects rated the turning bed in terms of comfort and sleep quality. Subjects rated the turning bed as more comfortable than their own bed and expressed satisfaction at the pain relief attained when on the turning bed. While using the turning bed, there was a significant improvement in sleep quality. No skin breakdown or deterioration in respiratory status occurred. Fewer subjects required the assistance of a caregiver for turning when on the turning bed. This automated turning bed shows great promise in meeting a need for patients with limited mobility whether they are homebound or in a residential community. Future studies that further investigate use of the turning bed for postoperative back patients while still in the acute care setting are indicated. Replicative studies with a larger sample size are also indicated.

and γγ-turns in proteins revisited: A new set of amino acid turn-type de

Indian Academy of Sciences (India)

cent Protein Data Bank has nearly doubled and the number of γ-turns in a representative set of 320 proteins has in- creased over seven times since the previous analysis. β-turns (7153) and γ-turns (911) extracted from these proteins were used to derive a revised set of type-dependent amino acid positional preferences and ...

Conformational interconversions in peptide beta-turns: analysis of turns in proteins and computational estimates of barriers.

Science.gov (United States)

Gunasekaran, K; Gomathi, L; Ramakrishnan, C; Chandrasekhar, J; Balaram, P

1998-12-18

The two most important beta-turn features in peptides and proteins are the type I and type II turns, which differ mainly in the orientation of the central peptide unit. Facile conformational interconversion is possible, in principle, by a flip of the central peptide unit. Homologous crystal structures afford an opportunity to structurally characterize both possible conformational states, thus allowing identification of sites that are potentially stereochemically mobile. A representative data set of 250 high-resolution (turns that are assigned different conformational types (type I/type II) in related structures. A total of 55 examples of beta-turns were identified as possible candidates for a stereochemically mobile site. Of the 55 examples, 45 could be classified as a potential site for interconversion between type I and type II beta-turns, while ten correspond to flips from type I' to type II' structures. As a further check, the temperature factors of the central peptide unit carbonyl oxygen atom of the 55 examples were examined. The analysis reveals that the turn assignments are indeed reliable. Examination of the secondary structures at the flanking positions of the flippable beta-turns reveals that seven examples occur in the loop region of beta-hairpins, indicating that the formation of ordered secondary structures on either side of the beta-turn does not preclude local conformational variations. In these beta-turns, Pro (11 examples), Lys (nine examples) and Ser (seven examples) were most often found at the i+1 position. Glycine was found to occur overwhelmingly at position i+2 (28 examples), while Ser (seven examples) and Asn (six examples) were amongst the most frequent residues. Activation energy barriers for the interconversion between type I and type II beta-turns were computed using the peptide models Ac-Pro-Aib-NHMe and Ac-Pro-Gly-NHMe within the framework of the AM1 semi-empirical molecular orbital procedure. In order to have a uniform basis for

NetTurnP – Neural Network Prediction of Beta-turns by Use of Evolutionary Information and Predicted Protein Sequence Features

DEFF Research Database (Denmark)

Petersen, Bent; Lundegaard, Claus; Petersen, Thomas Nordahl

2010-01-01

is the highest reported performance on a two-class prediction of β-turn and not-β-turn. Furthermore NetTurnP shows improved performance on some of the specific β-turn types. In the present work, neural network methods have been trained to predict β-turn or not and individual β-turn types from the primary amino......β-turns are the most common type of non-repetitive structures, and constitute on average 25% of the amino acids in proteins. The formation of β-turns plays an important role in protein folding, protein stability and molecular recognition processes. In this work we present the neural network method...... NetTurnP, for prediction of two-class β-turns and prediction of the individual β-turn types, by use of evolutionary information and predicted protein sequence features. It has been evaluated against a commonly used dataset BT426, and achieves a Matthews correlation coefficient of 0.50, which...

Effects of turning on skin-bed interface pressures in healthy adults.

Science.gov (United States)

Peterson, Matthew J; Schwab, Wilhelm; van Oostrom, Johannes H; Gravenstein, Nikolaus; Caruso, Lawrence J

2010-07-01

This paper is a report of a study of the effects of lateral turning on skin-bed interface pressures in the sacral, trochanteric and buttock regions, and its effectiveness in unloading at-risk tissue. Minimizing skin-support surface interface pressure is important in pressure ulcer prevention, but the effect of standard patient repositioning on skin interface pressure has not been objectively established. Data were collected from 15 healthy adults from a university-affiliated hospital. Mapped 24-inch x 24-inch (2304 half-inch sensors) interface pressure profiles were obtained in the supine position, followed by lateral turning with pillow or wedge support and subsequent head-of-bed elevation to 30 degrees . Raising the head-of-bed to 30 degrees in the lateral position statistically significantly increased peak interface pressures and total area > or = 32 mmHg. Comparing areas > or = 32 mmHg from all positions, 93% of participants had skin areas with interface pressures > or = 32 mmHg throughout all positions (60 +/- 54 cm(2)), termed 'triple jeopardy areas'. The triple jeopardy area increased statistically significantly with wedges as compared to pillows (153 +/- 99 cm(2) vs. 48 +/- 47 cm(2), P turning by experienced intensive care unit nurses does not reliably unload all areas of high skin-bed interface pressures. These areas remain at risk for skin breakdown, and help to explain why pressure ulcers occur despite the implementation of standard preventive measures. Support materials for maintaining lateral turned positions can also influence tissue unloading and triple jeopardy areas.

Electrical Machines: Turn-to-Turn Capacitance in Formed Windings with Rectangular Cross-Section Wire

NARCIS (Netherlands)

Djukic, Nenad; Encica, L.; Paulides, Johan

2015-01-01

Calculation of turn-to-turn capacitance (Ctt) in electrical machines (EMs) with formed windings with rectangular cross-section wire is presented. Three calculation methods are used for the calculation of Ctt in case of rectangular conductors – finite element (FE) method and two previously published

The Reading Turn-Around: A Five Part Framework for Differentiated Instruction. Practitioners Bookshelf, Language & Literacy Series

Science.gov (United States)

Jones, Stephanie; Clarke, Lane; Enriquez, Grace

2009-01-01

This book demonstrates a five-part framework for teachers, reading specialists, and literacy coaches who want to help their least engaged students become powerful readers. Merging theory and practice, the guide offers successful strategies to reach your "struggling" learners. The authors show how you can "turn-around" your instructional practice,…

32 CFR 636.23 - Turning movements.

Science.gov (United States)

2010-07-01

... Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL... movements. (a) U-turns are prohibited on all streets in the cantonment area. (b) Right-turns will be made from a position as close to the right edge or right curb of the roadway as possible. (c) Left-turns...

Turn stability in beta-hairpin peptides: Investigation of peptides containing 3:5 type I G1 bulge turns.

Science.gov (United States)

Blandl, Tamas; Cochran, Andrea G; Skelton, Nicholas J

2003-02-01

The turn-forming ability of a series of three-residue sequences was investigated by substituting them into a well-characterized beta-hairpin peptide. The starting scaffold, bhpW, is a disulfide-cyclized 10-residue peptide that folds into a stable beta-hairpin with two antiparallel strands connected by a two-residue reverse turn. Substitution of the central two residues with the three-residue test sequences leads to less stable hairpins, as judged by thiol-disulfide equilibrium measurements. However, analysis of NMR parameters indicated that each molecule retains a significant folded population, and that the type of turn adopted by the three-residue sequence is the same in all cases. The solution structure of a selected peptide with a PDG turn contained an antiparallel beta-hairpin with a 3:5 type I + G1 bulge turn. Analysis of the energetic contributions of individual turn residues in the series of peptides indicates that substitution effects have significant context dependence, limiting the predictive power of individual amino acid propensities for turn formation. The most stable and least stable sequences were also substituted into a more stable disulfide-cyclized scaffold and a linear beta-hairpin scaffold. The relative stabilities remained the same, suggesting that experimental measurements in the bhpW context are a useful way to evaluate turn stability for use in protein design projects. Moreover, these scaffolds are capable of displaying a diverse set of turns, which can be exploited for the mimicry of protein loops or for generating libraries of reverse turns.

Turning collectors for solar radiation

Science.gov (United States)

Barak, Amitzur Z.

1976-01-01

A device is provided for turning a solar collector about the polar axis so that the collector is directed toward the sun as the sun tracks the sky each day. It includes two heat-expansive elements and a shadow plate. In the morning a first expansive element is heated, expands to turn the collector to face the sun, while the second expansive element is shaded by the plate. In the afternoon the second element is heated, expands to turn the collector to face the sun, while the first is shaded by the plate.

NetTurnP – Neural Network Prediction of Beta-turns by Use of Evolutionary Information and Predicted Protein Sequence Features

Science.gov (United States)

Petersen, Bent; Lundegaard, Claus; Petersen, Thomas Nordahl

2010-01-01

β-turns are the most common type of non-repetitive structures, and constitute on average 25% of the amino acids in proteins. The formation of β-turns plays an important role in protein folding, protein stability and molecular recognition processes. In this work we present the neural network method NetTurnP, for prediction of two-class β-turns and prediction of the individual β-turn types, by use of evolutionary information and predicted protein sequence features. It has been evaluated against a commonly used dataset BT426, and achieves a Matthews correlation coefficient of 0.50, which is the highest reported performance on a two-class prediction of β-turn and not-β-turn. Furthermore NetTurnP shows improved performance on some of the specific β-turn types. In the present work, neural network methods have been trained to predict β-turn or not and individual β-turn types from the primary amino acid sequence. The individual β-turn types I, I', II, II', VIII, VIa1, VIa2, VIba and IV have been predicted based on classifications by PROMOTIF, and the two-class prediction of β-turn or not is a superset comprised of all β-turn types. The performance is evaluated using a golden set of non-homologous sequences known as BT426. Our two-class prediction method achieves a performance of: MCC  = 0.50, Qtotal = 82.1%, sensitivity  = 75.6%, PPV  = 68.8% and AUC  = 0.864. We have compared our performance to eleven other prediction methods that obtain Matthews correlation coefficients in the range of 0.17 – 0.47. For the type specific β-turn predictions, only type I and II can be predicted with reasonable Matthews correlation coefficients, where we obtain performance values of 0.36 and 0.31, respectively. Conclusion The NetTurnP method has been implemented as a webserver, which is freely available at http://www.cbs.dtu.dk/services/NetTurnP/. NetTurnP is the only available webserver that allows submission of multiple sequences. PMID:21152409

Predicting turns in proteins with a unified model.

Directory of Open Access Journals (Sweden)

Qi Song

Full Text Available MOTIVATION: Turns are a critical element of the structure of a protein; turns play a crucial role in loops, folds, and interactions. Current prediction methods are well developed for the prediction of individual turn types, including α-turn, β-turn, and γ-turn, etc. However, for further protein structure and function prediction it is necessary to develop a uniform model that can accurately predict all types of turns simultaneously. RESULTS: In this study, we present a novel approach, TurnP, which offers the ability to investigate all the turns in a protein based on a unified model. The main characteristics of TurnP are: (i using newly exploited features of structural evolution information (secondary structure and shape string of protein based on structure homologies, (ii considering all types of turns in a unified model, and (iii practical capability of accurate prediction of all turns simultaneously for a query. TurnP utilizes predicted secondary structures and predicted shape strings, both of which have greater accuracy, based on innovative technologies which were both developed by our group. Then, sequence and structural evolution features, which are profile of sequence, profile of secondary structures and profile of shape strings are generated by sequence and structure alignment. When TurnP was validated on a non-redundant dataset (4,107 entries by five-fold cross-validation, we achieved an accuracy of 88.8% and a sensitivity of 71.8%, which exceeded the most state-of-the-art predictors of certain type of turn. Newly determined sequences, the EVA and CASP9 datasets were used as independent tests and the results we achieved were outstanding for turn predictions and confirmed the good performance of TurnP for practical applications.

What 'empirical turn in bioethics'?

Science.gov (United States)

Hurst, Samia

2010-10-01

Uncertainty as to how we should articulate empirical data and normative reasoning seems to underlie most difficulties regarding the 'empirical turn' in bioethics. This article examines three different ways in which we could understand 'empirical turn'. Using real facts in normative reasoning is trivial and would not represent a 'turn'. Becoming an empirical discipline through a shift to the social and neurosciences would be a turn away from normative thinking, which we should not take. Conducting empirical research to inform normative reasoning is the usual meaning given to the term 'empirical turn'. In this sense, however, the turn is incomplete. Bioethics has imported methodological tools from empirical disciplines, but too often it has not imported the standards to which researchers in these disciplines are held. Integrating empirical and normative approaches also represents true added difficulties. Addressing these issues from the standpoint of debates on the fact-value distinction can cloud very real methodological concerns by displacing the debate to a level of abstraction where they need not be apparent. Ideally, empirical research in bioethics should meet standards for empirical and normative validity similar to those used in the source disciplines for these methods, and articulate these aspects clearly and appropriately. More modestly, criteria to ensure that none of these standards are completely left aside would improve the quality of empirical bioethics research and partly clear the air of critiques addressing its theoretical justification, when its rigour in the particularly difficult context of interdisciplinarity is what should be at stake.

CONNECTION OF TURN AHEAD AND TURN BACK WITH MOTORIC ABILITIES OF THE FOURTH GRADE OF HIGH SCHOOL

Directory of Open Access Journals (Sweden)

Jovica Petković

2008-08-01

Full Text Available The research is done for the purpose of determination and defining of the level of connection between some motoric abilities with success in realization of programmed contents from the area of gymnastics (turn ahead and turn back. The research is done on the sample of fifty students from the fourth grade of High School, on ten motoric tests and on two specific motoric assignments – turn ahead and turn back. The results of this research clearly point that there exist the multitude of statistically important coefficients of correlation between treated motoric abilities and applied motoric assignments.

The Philosophy of Turning Points

DEFF Research Database (Denmark)

Turcan, Romeo V.

2013-01-01

business and management field, the turning point is seen as a valuable unit of analysis within the research field. It is expected that this paper will encourage a dynamic scholarly conversation about the concept of turning point and how it can aid international business researchers in the development...

Prediction of beta-turns with learning machines.

Science.gov (United States)

Cai, Yu-Dong; Liu, Xiao-Jun; Li, Yi-Xue; Xu, Xue-biao; Chou, Kuo-Chen

2003-05-01

The support vector machine approach was introduced to predict the beta-turns in proteins. The overall self-consistency rate by the re-substitution test for the training or learning dataset reached 100%. Both the training dataset and independent testing dataset were taken from Chou [J. Pept. Res. 49 (1997) 120]. The success prediction rates by the jackknife test for the beta-turn subset of 455 tetrapeptides and non-beta-turn subset of 3807 tetrapeptides in the training dataset were 58.1 and 98.4%, respectively. The success rates with the independent dataset test for the beta-turn subset of 110 tetrapeptides and non-beta-turn subset of 30,231 tetrapeptides were 69.1 and 97.3%, respectively. The results obtained from this study support the conclusion that the residue-coupled effect along a tetrapeptide is important for the formation of a beta-turn.

Turn-Based War Chess Model and Its Search Algorithm per Turn

Directory of Open Access Journals (Sweden)

Hai Nan

2016-01-01

Full Text Available War chess gaming has so far received insufficient attention but is a significant component of turn-based strategy games (TBS and is studied in this paper. First, a common game model is proposed through various existing war chess types. Based on the model, we propose a theory frame involving combinational optimization on the one hand and game tree search on the other hand. We also discuss a key problem, namely, that the number of the branching factors of each turn in the game tree is huge. Then, we propose two algorithms for searching in one turn to solve the problem: (1 enumeration by order; (2 enumeration by recursion. The main difference between these two is the permutation method used: the former uses the dictionary sequence method, while the latter uses the recursive permutation method. Finally, we prove that both of these algorithms are optimal, and we analyze the difference between their efficiencies. An important factor is the total time taken for the unit to expand until it achieves its reachable position. The factor, which is the total number of expansions that each unit makes in its reachable position, is set. The conclusion proposed is in terms of this factor: Enumeration by recursion is better than enumeration by order in all situations.

Study on Turn-to-turn Short Circuit On一line Monitoring System for Dry一type Ai r一core Reactor

Directory of Open Access Journals (Sweden)

GAO Zi-wei

2017-04-01

Full Text Available The change of current value caused by turn-to-turn short circuit of dry-type air-core reactor is so little that failure detection is difficult to be carried out. In order to solve this problem，a new on-line monitoring system based on impedance variation of turn-to-turn short circuit is proposed. The numerical method is applied to analyze the variation of equivalent resistance and equivalent reactance when dry-type air-core reactor winding short circuit happens in different places，and the monitoring method based on harmonic analysis method and quasi- synchronization sampling method is analyzed by theory. The hardware system，which takes single-chip microcomputer as the core of data processing and logic control，completes data acquisition of voltage signal and current signal of the reactor. In the respect of software design，the impedance variation will be uploaded to the PC after it has been calculated by using the above monitoring method，and then monitoring of turn-to-turn short circuit fault will be realized. Finally，the design of on-line monitoring system is studied by testing. The research result shows that，the equivalent resistance increases and the equivalent reactance decreases when turn-to-turn short circuit occurs，and the variation of equivalent resistance is more obvious than equivalent reactance. The experiment results prove that this monitoring method is true and the on-line monitoring system is feasible.

"Why doesn't she seek help for partner abuse?" An exploratory study with South Asian immigrant women.

Science.gov (United States)

Ahmad, Farah; Driver, Natasha; McNally, Mary Jane; Stewart, Donna E

2009-08-01

This study explores why South Asian immigrant women with experiences of partner abuse delay seeking help from professionals. Three focus groups were conducted in Hindi language with South Asian immigrant women in Toronto. Twenty-two women participated with a mean age of 46 years (range 29-68 years). Thematic analysis was conducted on the transcribed data using constant comparison techniques within and across the groups. We found that three major themes emerged from the discussions: reasons for delayed help-seeking, turning points and talking to professionals. Women expressed delaying help-seeking to the point when "Pani sar se guzar jata he" (water crosses over your head). Their dominant reasons for delayed help-seeking were social stigma, rigid gender roles, marriage obligations, expected silence, loss of social support after migration and limited knowledge about available resources and myths about partner abuse. Women usually turned for help only after experiencing pronounced mental and physical health problems. The findings are interpreted in light of participants' immigration context and the socio-cultural norms of patriarchy, collectivism and familism. Prevention approaches to address partner abuse and delayed help-seeking among South Asian immigrant women should include tailored community education, social services to reduce vulnerability, and cultural competency of professionals. Further research and program evaluation is needed to advance the field.

Development process and data management of TurnSTEP, a STEP-compliant CNC system for turning

NARCIS (Netherlands)

Choi, I.; Suh, S.-H; Kim, K.; Song, M.S.; Jang, M.; Lee, B.-E.

2006-01-01

TurnSTEP is one of the earliest STEP-compliant CNC systems for turning. Based on the STEP-NC data model formalized as ISO 14649-12 and 121, it is designed to support intelligent and autonomous control of NC machines for e-manufacturing. The present paper introduces the development process and data

Determinants of the half-turn with the ball in sub-elite youth soccer players.

Science.gov (United States)

Zago, Matteo; Codari, Marina; Grilli, Massimo; Bellistri, Giuseppe; Lovecchio, Nicola; Sforza, Chiarella

2016-06-01

We explored the biomechanics of the 180° change-of-direction with the ball (half-turn) in soccer. We aimed at identifying movement strategies which enhance the players' half-turning performance, by characterising technique kinematics and understanding the structure of biomechanical and anthropometrics variables. Ten Under-13 sub-elite male players were recorded with an optoelectronic motion analyser while performing a 5-m straight dribbling followed by a half-turn with the sole. Joints kinematics differences between faster and slower trials were found in support-side hip rotation, driving-side hip adduction, trunk flexion and rotation, and arms abduction. To unveil the data-set structure, a principal component (PC) analysis and a stepwise linear discriminant analysis were performed using 30 biomechanical parameters and four anthropometric variables for each trial. Seven retained PCs explained 79% of the overall variability, featuring combinations of original variables that help in understanding the factors facilitating fast half-turns: keeping short steps, minimising lateral and forward body movements, and centre-of-mass lowering, even with ample lower limbs ranges of motion (RoM); abducting the upper limbs while limiting trunk flexion and pelvic inclination RoM. Balance and task-constrained exercises may be proposed to improve this technique. Moreover, a quantitative knowledge of the movement structure could give coaches objective insights to better instruct young players.

Characterization of sediment in a leaching trench RCRA (Resource Conservation and Recovery Act) site

International Nuclear Information System (INIS)

Zimmerman, M.G.; Kossik, C.D.

1988-01-01

Hazardous materials potentially were disposed of into a pair of leaching trenches from 1975 until Resource Conservation and Recovery Act (RCRA) regulations were imposed in 1985. These leaching trenches now are used for disposal of nonhazardous process water. The typical effluent (approximately 3 million gal/d) consisted of water with trace quantities of laboratory, maintenance, and fuel fabrication process chemicals. The largest constituent in the waste stream was uranium in low concentrations. This paper describes the project used to analyze and characterize the sediments in and below the leaching trenches. Two phases of sediment sampling were performed. The first phase consisted of taking samples between the bottom of the trenches and groundwater to locate contamination in the deep sediments under the trenches. To accomplish this sampling, a series of wells were drilled, and samples were obtained for every five feet in depth. The second phase consisted of samples taken at three depths in a series of positions along each trench. Sampling was completed to determine contamination levels in the shallow sediments and loose material washed into the trenches from the process sewer system. The project results were that no measurable contamination was found in the deep sediments. Measurable contamination from metals, such as chromium and nickel, was found in the shallow sediments. The primary contaminant in the shallow sediments was uranium. The concentration of contaminants decreased rapidly to near-background levels at shallow depths below the bottoms of the trenches

Data-driven battery product development: Turn battery performance into a competitive advantage.

Energy Technology Data Exchange (ETDEWEB)

Sholklapper, Tal [Voltaiq, Inc.

2016-04-19

Poor battery performance is a primary source of user dissatisfaction across a broad range of applications, and is a key bottleneck hindering the growth of mobile technology, wearables, electric vehicles, and grid energy storage. Engineering battery systems is difficult, requiring extensive testing for vendor selection, BMS programming, and application-specific lifetime testing. This work also generates huge quantities of data. This presentation will explain how to leverage this data to help ship quality products faster using fewer resources while ensuring safety and reliability in the field, ultimately turning battery performance into a competitive advantage.

Fast Turn-off Mine Transient Electromagnetic Transmitter System

Directory of Open Access Journals (Sweden)

ZHENG Xiao-Liang

2014-05-01

Full Text Available For solving problems such as short turn-off time, high linear degree of falling edge, measurement of turn-off time and influence of primary signals for transient electromagnetic transmitter, and restrictions because of the environmental conditions of underground coal mine, this thesis aims at designing a new transient electromagnetic transmitter system suitable for coal mine. Supported by damping absorption circuit, such system applies small volume, sectional transmitting coil, with features of short turn-off time, high linear degree of current falling edge. It uses the transmitter monitoring circuit, which accurately measures turn-off time and simultaneously records the current value changes after turn-off, thus to eliminate the influence of primary field as well as to restore earlier secondary field signals for reference and finally to improve the ability to detect the shallow structure. It turns out that the new system has a shorter turn-off time, a higher linear degree of current falling and more accurate data record of turn-off current.

Prostate Cancer Research Trial Helps John Spencer Treat His Cancer | NIH MedlinePlus the Magazine

Science.gov (United States)

... of this page please turn Javascript on. Feature: Prostate Cancer Prostate Cancer Research Trial Helps John Spencer Treat His Cancer ... because of timely detection and treatment of his prostate cancer. He participated in an NIH-sponsored clinical trial. ...

Increasing protein stability by improving beta-turns.

Science.gov (United States)

Fu, Hailong; Grimsley, Gerald R; Razvi, Abbas; Scholtz, J Martin; Pace, C Nick

2009-11-15

Our goal was to gain a better understanding of how protein stability can be increased by improving beta-turns. We studied 22 beta-turns in nine proteins with 66-370 residues by replacing other residues with proline and glycine and measuring the stability. These two residues are statistically preferred in some beta-turn positions. We studied: Cold shock protein B (CspB), Histidine-containing phosphocarrier protein, Ubiquitin, Ribonucleases Sa2, Sa3, T1, and HI, Tryptophan synthetase alpha-subunit, and Maltose binding protein. Of the 15 single proline mutations, 11 increased stability (Average = 0.8 +/- 0.3; Range = 0.3-1.5 kcal/mol), and the stabilizing effect of double proline mutants was additive. On the basis of this and our previous work, we conclude that proteins can generally be stabilized by replacing nonproline residues with proline residues at the i + 1 position of Type I and II beta-turns and at the i position in Type II beta-turns. Other turn positions can sometimes be used if the phi angle is near -60 degrees for the residue replaced. It is important that the side chain of the residue replaced is less than 50% buried. Identical substitutions in beta-turns in related proteins give similar results. Proline substitutions increase stability mainly by decreasing the entropy of the denatured state. In contrast, the large, diverse group of proteins considered here had almost no residues in beta-turns that could be replaced by Gly to increase protein stability. Improving beta-turns by substituting Pro residues is a generally useful way of increasing protein stability. 2009 Wiley-Liss, Inc.

Anticipation in turn-taking: mechanisms and information sources.

Science.gov (United States)

Riest, Carina; Jorschick, Annett B; de Ruiter, Jan P

2015-01-01

During conversations participants alternate smoothly between speaker and hearer roles with only brief pauses and overlaps. There are two competing types of accounts about how conversationalists accomplish this: (a) the signaling approach and (b) the anticipatory ('projection') approach. We wanted to investigate, first, the relative merits of these two accounts, and second, the relative contribution of semantic and syntactic information to the timing of next turn initiation. We performed three button-press experiments using turn fragments taken from natural conversations to address the following questions: (a) Is turn-taking predominantly based on anticipation or on reaction, and (b) what is the relative contribution of semantic and syntactic information to accurate turn-taking. In our first experiment we gradually manipulated the information available for anticipation of the turn end (providing information about the turn end in advance to completely removing linguistic information). The results of our first experiment show that the distribution of the participants' estimation of turn-endings for natural turns is very similar to the distribution for pure anticipation. We conclude that listeners are indeed able to anticipate a turn-end and that this strategy is predominantly used in turn-taking. In Experiment 2 we collected purely reacted responses. We used the distributions from Experiments 1 and 2 together to estimate a new dependent variable called Reaction Anticipation Proportion. We used this variable in our third experiment where we manipulated the presence vs. absence of semantic and syntactic information by low-pass filtering open-class and closed class words in the turn. The results suggest that for turn-end anticipation, both semantic and syntactic information are needed, but that the semantic information is a more important anticipation cue than syntactic information.

Breaking New Ground with High Resolution Turn-By-Turn BPMs at the ESRF

CERN Document Server

Farvacque, L; Scheidt, K

2001-01-01

This High-Resolution, Turn-by-Turn BPM system is a low-cost extension to the existing BPM system, based on the RF-multiplexing concept, used for slow Closed-Orbit measurements. With this extension Beam Position measurements in both planes, at all (224) BPMs in the 844 m ESRF Storage Ring, for up to 2048 Orbit Turns with 1 μm resolution are performed. The data acquisition is synchronised to a single, flat 1 μs, transverse deflection kick to the 1μs beamfill in the 2.8μs revolution period. The high quality of this synchronisation, together with the good reproducibility of the deflection kick and the overall stability of the Closed Orbit beam allows to repeat the kick and acquisition in many cycles. The subsequent averaging of the data obtained in these cycles yields the 1um resolution. The latter allows lattice measurements with high precision such as the localisation of very small focussing errors and modulation in Beta values and phase advances. It also finds an unique ...

Laterality of the lower limbs and carving turns

Directory of Open Access Journals (Sweden)

F Vaverka

2010-06-01

Full Text Available The aim of this study is to discover whether the lateral preference of the lower limbs influences the execution of successive carving turns or not. Six skilled skiers (men, right lower limb preference, age 26.5±1.61 years old, height 1.80±0.04 m, body weight 78.83±5.46 kg executed 30 (18 left, 12 right symmetrical carving turns. Kinetic analysis of the final vertical component of reaction force FZ(t measured dynamometrically provided the information about the time of initiation and steering phases of the turn and the maximum force, average force and force impulse. Differences between right and left turns are not statistically significant. Factual analyses of the magnitude of measured variables confirmed that left turns were found to have a longer duration, a shorter initiation and longer steering phase, and higher level of produced force and force impulse in comparison with right turns. Based on the results it can be concluded that the turns where the outer leg is the preferred limb are preferentially used to regulate the speed of the ride. The study of laterality in symmetrical carving turns has proven that lateral preference of lower extremities influences the execution of the turn also by expert skiers.

Wittgenstein and the linguistic turn in social theory

DEFF Research Database (Denmark)

Hermansen, Jens Christian

of Winch in social theory, the wider and more recent influence of Wittgenstein in areas such as technology and science studies, social theory, feminist and gender studies and conversation and discourse analysis is also considered. Historically, the readings of Wittgenstein in the social sciences have taken...... of the linguistic turn in social theory, the linguistic turn is a double-edged sword of both profound insights and limits; the claim is that the limits of the linguistic turn are the strengths of functionalist, structuralist and materialist approaches to the social sciences. The approach of the critical turn...... is to develop a more comprehensive social theory that is sensitive to these strengths and thus supersedes the limits of the linguistic turn. This paper suggests a different approach. Against the critical turn, the paper argues that the limits of the linguistic turn are identical with the very assumptions...

Characterization of beta-turn and Asx-turns mimicry in a model peptide: stabilization via C--H . . . O interaction.

Science.gov (United States)

Thakur, A K; Kishore, R

2006-04-15

The chemical synthesis and single-crystal X-ray diffraction analysis of a model peptide, Boc-Thr-Thr-NH2 (1) comprised of proteinogenic residues bearing an amphiphilic Cbeta -stereogenic center, has been described. Interestingly, the analysis of its molecular structure revealed the existence of a distinct conformation that mimics a typical beta-turn and Asx-turns, i.e., the two Thr residues occupy the left- and right-corner positions. The main-chain torsion angles of the N- and C-terminal residues i.e., semiextended: phi = -68.9 degrees , psi = 128.6 degrees ; semifolded: phi = -138.1 degrees , psi = 2.5 degrees conformations, respectively, in conjunction with a gauche- disposition of the obligatory C-terminus Thr CgammaH3 group, characterize the occurrence of the newly described beta-turn- and Asx-turns-like topology. The preferred molecular structure is suggested to be stabilized by an effective nonconventional main-chain to side-chain Ci=O . . . H--Cgamma(i+2)-type intraturn hydrogen bond. Noteworthy, the observed topology of the resulting 10-membered hydrogen-bonded ring is essentially similar to the one perceived for a classical beta-turn and the Asx-turns, stabilized by a conventional intraturn hydrogen bond. Considering the signs as well as magnitudes of the backbone torsion angles and the orientation of the central peptide bond, the overall mimicked topology resembles the type II beta-turn or type II Asx-turns. An analysis of Xaa-Thr sequences in high-resolution X-ray elucidated protein structures revealed the novel topology prevalence in functional proteins (unpublished). In view of indubitable structural as well as functional importance of nonconventional interactions in bioorganic and biomacromolecules, we intend to highlight the participation of Thr CgammaH in the creation of a short-range C=O . . . H--Cgamma -type interaction in peptides and proteins. Copyright 2006 Wiley Periodicals, Inc.

METHODICAL MODEL FOR TEACHING BASIC SKI TURN

Directory of Open Access Journals (Sweden)

Danijela Kuna

2013-07-01

Full Text Available With the aim of forming an expert model of the most important operators for basic ski turn teaching in ski schools, an experiment was conducted on a sample of 20 ski experts from different countries (Croatia, Bosnia and Herzegovina and Slovenia. From the group of the most commonly used operators for teaching basic ski turn the experts picked the 6 most important: uphill turn and jumping into snowplough, basic turn with hand sideways, basic turn with clapping, ski poles in front, ski poles on neck, uphill turn with active ski guiding. Afterwards, ranking and selection of the most efficient operators was carried out. Due to the set aim of research, a Chi square test was used, as well as the differences between frequencies of chosen operators, differences between values of the most important operators and differences between experts due to their nationality. Statistically significant differences were noticed between frequencies of chosen operators (c2= 24.61; p=0.01, while differences between values of the most important operators were not obvious (c2= 1.94; p=0.91. Meanwhile, the differences between experts concerning thier nationality were only noticeable in the expert evaluation of ski poles on neck operator (c2=7.83; p=0.02. Results of current research are reflected in obtaining useful information about methodological priciples of learning basic ski turn organization in ski schools.

Informing Physics: Jacob Bekenstein and the Informational Turn in Theoretical Physics

Science.gov (United States)

Belfer, Israel

2014-03-01

In his PhD dissertation in the early 1970s, the Mexican-Israeli theoretical physicist Jacob Bekenstein developed the thermodynamics of black holes using a generalized version of the second law of thermodynamics. This work made it possible for physicists to describe and analyze black holes using information-theoretical concepts. It also helped to transform information theory into a fundamental and foundational concept in theoretical physics. The story of Bekenstein's work—which was initially opposed by many scientists, including Stephen Hawking—highlights the transformation within physics towards an information-oriented scientific mode of theorizing. This "informational turn" amounted to a mild-mannered revolution within physics, revolutionary without being rebellious.

Experience sharing, emotional reciprocity, and turn-taking

Directory of Open Access Journals (Sweden)

Melisa eStevanovic

2015-04-01

Full Text Available In this perspective article, we consider the relationship between experience sharing and turn-taking. There is much evidence suggesting that human social interaction is permeated by two temporal organizations: (1 the sequential framework of turn-taking and (2 the concurrent framework of emotional reciprocity. From this perspective, we introduce two alternative hypotheses about how the relationship between experience sharing and turn-taking could be viewed. According to the first hypothesis, the home environment of experience sharing is in the concurrent framework of emotional reciprocity, while the motivation to share experiences is in tension with the sequential framework of turn-taking. According to the second hypothesis, then again, people’s inclination to coordinate their actions in terms of turn-taking is motivated precisely by their propensity to share experiences. We consider theoretical and empirical ideas in favor of both of these hypotheses and discuss their implications for future research.

Exploring interaction between a non-speaking boy using aided AAC and his everyday communication partners: features of turn organizing and turn design

DEFF Research Database (Denmark)

Pilesjö, Maja Sigurd; Rasmussen, Gitte

2011-01-01

-at-action is suggested. The analyses demonstrate that the boy’s turn-at-actions are oriented to as a co-constructed and thus interactionally achieved unit: the boy points at a bliss symbol which is given voice by the speaking co-participant. In and through the relevant made voicing of the turn-at-action, a turn...... AAC, bliss symbolics. The analysis indicates that the participants can collaborately create and orient to units in interaction equivalent to turns in interaction although they differ dramatically from ordinary turns-at-talk. In order to capture the nature of the described units, the category turn...

Turning for Ulcer Reduction (TURN) Study: An Economic Analysis.

Science.gov (United States)

Paulden, Mike; Bergstrom, Nancy; Horn, Susan D; Rapp, Mary; Stern, Anita; Barrett, Ryan; Watkiss, Michael; Krahn, Murray

2014-01-01

The Turning for Ulcer Reduction (TURN) study was a multisite, randomized controlled trial that aimed to determine the optimal frequency of turning nursing facility residents with mobility limitations who are at moderate and high risk for pressure ulcer (PrU) development. Here we present data from the economic analysis. This economic analysis aims to estimate the economic consequences for Ontario of switching from a repositioning schedule of 2-hour intervals to a schedule of 3-hour or 4-hour intervals. Costs considered in the analysis included those associated with nursing staff time spent repositioning residents and with incontinent care supplies, which included briefs, barrier cream, and washcloths. The total economic benefit of switching to 3-hour or 4-hour repositioning is estimated to be $11.05 or $16.74 per day, respectively, for every resident at moderate or high risk of developing PrUs. For a typical facility with 123 residents, 41 (33%) of whom are at moderate or high risk of developing PrUs, the total economic benefit is estimated to be $453 daily for 3-hour or $686 daily for 4-hour repositioning. For Ontario as a whole, assuming that there are 77,933 residents at 634 LTC facilities, 25,927 (33%) of whom are at moderate or high risk of developing PrUs, the total economic benefits of switching to 3-hour or 4-hour repositioning are estimated to be $286,420 or $433,913 daily, respectively, equivalent to $104.5 million or $158.4 million per year. We did not consider the savings the Ontario Ministry of Health and Long-Term Care might incur should less frequent repositioning reduce the incidence of work-related injury among nursing staff, so our findings are potentially conservative. A switch to 3-hour or 4-hour repositioning appears likely to yield substantial economic benefits to Ontario without placing residents at greater risk of developing PrUs.

Primordial spectra from sudden turning trajectory

Science.gov (United States)

Noumi, Toshifumi; Yamaguchi, Masahide

2013-12-01

Effects of heavy fields on primordial spectra of curvature perturbations are discussed in inflationary models with a sudden turning trajectory. When heavy fields are excited after the sudden turn and oscillate around the bottom of the potential, the following two effects are generically induced: deformation of the inflationary background spacetime and conversion interactions between adiabatic and isocurvature perturbations, both of which can affect the primordial density perturbations. In this paper, we calculate primordial spectra in inflationary models with sudden turning potentials taking into account both of the two effects appropriately. We find that there are some non-trivial correlations between the two effects in the power spectrum and, as a consequence, the primordial scalar power spectrum has a peak around the scale exiting the horizon at the turn. Though both effects can induce parametric resonance amplifications, they are shown to be canceled out for the case with the canonical kinetic terms. The peak feature and the scale dependence of bispectra are also discussed.

Annual Report RCRA Post-Closure Monitoring and Inspections for CAU 112: Area 23 Hazardous Waste Trenches, Nevada Test Site, Nevada, for the period October 2000-July 2001

International Nuclear Information System (INIS)

Tobiason, D. S.

2002-01-01

This annual Neutron Soil Moisture Monitoring report provides an analysis and summary for site inspections, meteorological information, and neutron soil moisture monitoring data obtained at the Area 23 Hazardous Waste Trenches Resource Conservation and Recovery Act (RCRA) unit, located in Area 23 of the Nevada Test Site, Nye County, Nevada, during the October 2000--July 2001 monitoring period. Inspections of the Area 23 Hazardous Waste Trenches RCRA unit are conducted to determine and document the physical condition of the covers, facilities, and any unusual conditions that could impact the proper operation of the waste unit closure. Physical inspections of the closure were completed quarterly and indicated that the site is in good condition with no significant findings noted. An annual subsidence survey of the elevation markers was conducted in July 2001. There has been no subsidence at any of the markers since monitoring began eight years ago. Precipitation for the period October 2000 through July 2001 was 9.42 centimeters (cm) (3.71 inches [in]) (U.S. National Weather Service, 2001). The prior year annual rainfall (January 2000 through December 2000) was 10.44 cm (4.1 1 in.). The recorded average annual rainfall for this site from 1972 to January 2000 is 14.91 cm (5.87 in.). The objective of the neutron logging program is to monitor the soil moisture conditions along 30 neutron access tubes and detect changes that may be indicative of moisture movement at a point located directly beneath each trench. All monitored access tubes are within the compliance criteria of less than 5 percent residual volumetric moisture content at the compliance point directly beneath each respective trench. Soil conditions remain dry and stable underneath the trenches

Kantian Turning Point in Gadamer's Philosophical Hermeneutics

Directory of Open Access Journals (Sweden)

Kristína Bosáková

2016-11-01

Full Text Available The paper is treating the theme of a Kantian turning-point in the philosophical hermeneutics of H.- G. Gadamer based on of the harmonic relationship between metaphysics and science in Kantian philosophy from the point of view of the philosophical hermeneutics of Gadamer. The philosophical work of Kant had such an influence on Gadamer that without exaggerating we can talk about the Kantian turning-point in Gadamerian hermeneutics. Grondin, a former student of Gadamer, is talking about Kantian turning-point on the field of aesthetics, but in reality Kantian turning-point means much more than a mere change in the reception of the concept of judgement. It is a discovery of harmonical relationship between the beauty and the moral, between the reason and the sensitivity, between the modern sciences and the metaphysical tradition in the Kantian philosophy, made by Gadamer. This is what we call the Kantian turning-point in Gadamerian hermeneutics.

Environmental, health, and safety issues of sodium-sulfur batteries for electric and hybrid vehicles. Volume 2, Battery recycling and disposal

Energy Technology Data Exchange (ETDEWEB)

Corbus, D

1992-09-01

Recycling and disposal of spent sodium-sulfur (Na/S) batteries are important issues that must be addressed as part of the commercialization process of Na/S battery-powered electric vehicles. The use of Na/S batteries in electric vehicles will result in significant environmental benefits, and the disposal of spent batteries should not detract from those benefits. In the United States, waste disposal is regulated under the Resource Conservation and Recovery Act (RCRA). Understanding these regulations will help in selecting recycling and disposal processes for Na/S batteries that are environmentally acceptable and cost effective. Treatment processes for spent Na/S battery wastes are in the beginning stages of development, so a final evaluation of the impact of RCRA regulations on these treatment processes is not possible. The objectives of tills report on battery recycling and disposal are as follows: Provide an overview of RCRA regulations and requirements as they apply to Na/S battery recycling and disposal so that battery developers can understand what is required of them to comply with these regulations; Analyze existing RCRA regulations for recycling and disposal and anticipated trends in these regulations and perform a preliminary regulatory analysis for potential battery disposal and recycling processes. This report assumes that long-term Na/S battery disposal processes will be capable of handling large quantities of spent batteries. The term disposal includes treatment processes that may incorporate recycling of battery constituents. The environmental regulations analyzed in this report are limited to US regulations. This report gives an overview of RCRA and discusses RCRA regulations governing Na/S battery disposal and a preliminary regulatory analysis for Na/S battery disposal.

Environmental, health, and safety issues of sodium-sulfur batteries for electric and hybrid vehicles

Energy Technology Data Exchange (ETDEWEB)

Corbus, D.

1992-09-01

Recycling and disposal of spent sodium-sulfur (Na/S) batteries are important issues that must be addressed as part of the commercialization process of Na/S battery-powered electric vehicles. The use of Na/S batteries in electric vehicles will result in significant environmental benefits, and the disposal of spent batteries should not detract from those benefits. In the United States, waste disposal is regulated under the Resource Conservation and Recovery Act (RCRA). Understanding these regulations will help in selecting recycling and disposal processes for Na/S batteries that are environmentally acceptable and cost effective. Treatment processes for spent Na/S battery wastes are in the beginning stages of development, so a final evaluation of the impact of RCRA regulations on these treatment processes is not possible. The objectives of tills report on battery recycling and disposal are as follows: Provide an overview of RCRA regulations and requirements as they apply to Na/S battery recycling and disposal so that battery developers can understand what is required of them to comply with these regulations; Analyze existing RCRA regulations for recycling and disposal and anticipated trends in these regulations and perform a preliminary regulatory analysis for potential battery disposal and recycling processes. This report assumes that long-term Na/S battery disposal processes will be capable of handling large quantities of spent batteries. The term disposal includes treatment processes that may incorporate recycling of battery constituents. The environmental regulations analyzed in this report are limited to US regulations. This report gives an overview of RCRA and discusses RCRA regulations governing Na/S battery disposal and a preliminary regulatory analysis for Na/S battery disposal.

Searching for Criteria in Evaluating the Monofin Swimming Turn from the Perspective of Coaching and Improving Technique

Science.gov (United States)

Rejman, Marek; Borowska, Grażyna

2008-01-01

and glide time. Key pointsShort time and large surface of the monofin additionally hinders complexity of the turn performance by disturbance in sensing and controlling body in water. Availability of no objective data on monofin swimming turns resulted in research in the field connected with specifying parameters needed for the technique evaluation.Correct turn technique may help to improve swimming race results.The diagram constructed on the basis of the interdependency of the total turn time and the remaining recorded kinematic parameters should establish the areas of searching for mechanism of effective and efficient monofin swimming turn.The most crucial, from the coaching and improving point of view, seem to be activities which take place from the moment of feet wall contact till the first propulsive movements. Therefore, the high quality of the monofin swimming turn technique is not just a simple consequence of the fastest performance of all its component parts.The most important criteria of the quality in the monofin swimming turn technique are: striving for extending in the optimum scope of wall contact time, the time of the push-off phase and the glide time. PMID:24150136

Review Essay: Turn, Turn, Turn Around—Till Categories Blur

Directory of Open Access Journals (Sweden)

Lars Allolio-Näcke

2008-01-01

Full Text Available I begin this review by introducing the book and discussing its manifest content chapter by chapter (see 2.1, focusing particularly on the author's argumentation concerning the development of new orientations in cultural studies and on how, in relation to the turns discussed, the names of the researchers and central categories involved are collected. In a second step, I give a close reading of the book's latent content, which I consider to be more important (see 2.2. In this context I discuss several questions of scientific politics—especially the issue of hegemonic claims. Thirdly, I read the book from the critical standpoint of a psychologist, a sociologist and a theologian and show the shortcomings of BACHMANN-MEDICK's outsider perspective on these disciplines. In this regard I read the book again and provide a critique of the quality of the author's scientific performance (see 3. Finally, I state the reasons I do not recommend reading this book (see 4. URN: urn:nbn:de:0114-fqs0801266

[Study of beta-turns in globular proteins].

Science.gov (United States)

Amirova, S R; Milchevskiĭ, Iu V; Filatov, I V; Esipova, N G; Tumanian, V G

2005-01-01

The formation of beta-turns in globular proteins has been studied by the method of molecular mechanics. Statistical method of discriminant analysis was applied to calculate energy components and sequences of oligopeptide segments, and after this prediction of I type beta-turns has been drawn. The accuracy of true positive prediction is 65%. Components of conformational energy considerably affecting beta-turn formation were delineated. There are torsional energy, energy of hydrogen bonds, and van der Waals energy.

Data versus Spock: lay theories about whether emotion helps or hinders.

Science.gov (United States)

Karnaze, Melissa M; Levine, Linda J

2018-05-01

The android Data from Star Trek admired human emotion whereas Spock viewed emotion as irrational and maladaptive. The theory that emotions fulfil adaptive functions is widely accepted in academic psychology but little is known about laypeople's theories. The present study assessed the extent to which laypeople share Data's view of emotion as helpful or Spock's view of emotion as a hindrance. We also assessed how help and hinder theory endorsement were related to reasoning, emotion regulation, and well-being. Undergraduates (N = 630) completed a stressful timed reasoning task and questionnaires that assessed their theories of emotion, emotion regulation strategies, happiness, and social support. Overall, participants viewed emotion more as a help than a hindrance. The more they endorsed the view that emotion helps, the better their reasoning scores. Endorsing a help theory also predicted the use of reappraisal which, in turn, predicted greater happiness and social support. In contrast, endorsing the view that emotion hinders was associated with emotion suppression and less social support. Thus, people's theories about the functionality of emotion may have important implications for their reasoning and emotional well-being.

Tomographic reconstruction of transverse phase space from turn-by-turn profile data

CERN Document Server

Hancock, S; Lindroos, M

1999-01-01

Tomographic methods have the potential for useful application in beam diagnostics. The tomographic reconstruction of transverse phase space density from turn-by-turn profile data has been studied with particular attention to the effects of dispersion and chromaticity. It is shown that the modified Algebraic Reconstruction Technique (ART) that deals successfully with the problem of non-linear motion in the longitudinal plane cannot, in general, be extended to cover the transverse case. Instead, an approach is proposed in which the effect of dispersion is deconvoluted from the measured profiles before the phase space picture is reconstructed using either the modified ART algorithm or the inverse Radon Transform. This requires an accurate knowledge of the momentum distribution of the beam and the modified ART reconstruction of longitudinal phase space density yields just such information. The method has been tested extensively with simulated data.

Development of guidance for preparing treatability variance petitions from the RCRA Land Disposal Restrictions for DOE [Department of Energy] mixed-waste streams

International Nuclear Information System (INIS)

Harms, T.; Scheuer, N.; Martin, R.; Van Epp, T.; Triplett, M.

1990-01-01

In response to the Department of Energy's (DOE) anticipated need for variances from the Resource Conservation and Recovery Act (RCRA) Land Disposal Restriction (LDR) treatment requirements, a treatability variance guidance document is being prepared for use by DOE facilities and operations offices. The guidance document, although applicable to non-mixed hazardous waste streams, provides specific guidance regarding radioactive mixed-waste streams. Preparation of the guidance manual has involved developing an overview of the Land Disposal Restrictions, as well as an overview of the petition preparation process. The DOE internal review requirements are specifically addressed in the manual. Specific data requirements and engineering analyses are also described. A discussion of EPA's criteria for granting a treatability variance is also provided. A checklist for completeness of the petition is provided. Model language for use in DOE treatability variance petitions will be provided in a petition for a DOE waste stream as an appendix to the document

Learning From Our Past: How a Vietnam-Era Pacification Program Can Help Us Win in Afghanistan

Science.gov (United States)

2009-09-01

it as an operational and management problem—it was everybody’s business and nobody’s. It fell between the cracks . The reason I began zeroing in on...kind of help from us.”264 Farming programs can also help revive the economy by growing what other nations want to import: pomegranates , almonds...pistachios, raisins, and fruits such as apricots that can be dried or turned into juice.265 The Agribusiness Development Teams manned by state- based

Turning to Ontology in STS? Turning to STS through ‘Ontology’

NARCIS (Netherlands)

van Heur, B.; Leydesdorff, L.; Wyatt, S.

2012-01-01

We examine the evidence for the claim of an ‘ontological turn’ in science and technology studies (STS). Despite an increase in references to ‘ontology’ in STS since 1989, we show that there has not so much been an ontological turn as multiple discussions deploying the language of ontology,

Development of a QFD-based expert system for CNC turning centre selection

Science.gov (United States)

Prasad, Kanika; Chakraborty, Shankar

2015-12-01

Computer numerical control (CNC) machine tools are automated devices capable of generating complicated and intricate product shapes in shorter time. Selection of the best CNC machine tool is a critical, complex and time-consuming task due to availability of a wide range of alternatives and conflicting nature of several evaluation criteria. Although, the past researchers had attempted to select the appropriate machining centres using different knowledge-based systems, mathematical models and multi-criteria decision-making methods, none of those approaches has given due importance to the voice of customers. The aforesaid limitation can be overcome using quality function deployment (QFD) technique, which is a systematic approach for integrating customers' needs and designing the product to meet those needs first time and every time. In this paper, the adopted QFD-based methodology helps in selecting CNC turning centres for a manufacturing organization, providing due importance to the voice of customers to meet their requirements. An expert system based on QFD technique is developed in Visual BASIC 6.0 to automate the CNC turning centre selection procedure for different production plans. Three illustrative examples are demonstrated to explain the real-time applicability of the developed expert system.

FCC-hh turn-around cycle

CERN Document Server

Alemany Fernandez, Reyes; Bartmann, Wolfgang; Buffat, Xavier; Niemi, Arto; Schulte, Daniel; Solfaroli Camillocci, Matteo; Stoel, Linda

2016-01-01

The turn-around cycle time of a collider is defined as the time spent between the end of stable beams and the start of the next stable beams period, and its calculation is of fundamental importance. On one side it is a crucial ingredient for the computation of the optimal time spent in luminosity production, which defines the integrated luminosity per fill or store. On the other side, combined with the availability and reliability of the machine, it allows to perform a detailed breakdown of the operational performance of the collider over an operational season, i.e. percentage of time in stable beams and beam in the machine with respect to down time. This paper presents a preliminary operational cycle definition for the hadron-hadron Future Circular Collider, as a base line for estimating the corresponding turn-around time. The cycle definition is based on the Large Hadron Collider (LHC) operational cycle. Two turn-around times are presented, the theoretical one and a more realistic one based on the LHC exper...

Turning to alcohol?

International Nuclear Information System (INIS)

Reiboro, S.K.

1998-01-01

Brazil is examining whether turning to alcohol could solve its problems. The fuel alcohol producers are lobbying hard for the government to increase the use of alcohol to fuel the country's cars. Not only does using alcohol reduce CO 2 , runs the argument, but the Kyoto agreement might just attract international financing for the project. (author)

Silicon Carbide Emitter Turn-Off Thyristor

Directory of Open Access Journals (Sweden)

Jun Wang

2008-01-01

Full Text Available A novel MOS-controlled SiC thyristor device, the SiC emitter turn-off thyristor (ETO is a promising technology for future high-voltage switching applications because it integrates the excellent current conduction capability of a SiC thyristor with a simple MOS-control interface. Through unity-gain turn-off, the SiC ETO also achieves excellent Safe Operation Area (SOA and faster switching speeds than silicon ETOs. The world's first 4.5-kV SiC ETO prototype shows a forward voltage drop of 4.26 V at 26.5 A/cm2 current density at room and elevated temperatures. Tested in an inductive circuit with a 2.5 kV DC link voltage and a 9.56-A load current, the SiC ETO shows a fast turn-off time of 1.63 microseconds and a low 9.88 mJ turn-off energy. The low switching loss indicates that the SiC ETO could operate at about 4 kHz if 100 W/cm2 conduction and the 100 W/cm2 turn-off losses can be removed by the thermal management system. This frequency capability is about 4 times higher than 4.5-kV-class silicon power devices. The preliminary demonstration shows that the SiC ETO is a promising candidate for high-frequency, high-voltage power conversion applications, and additional developments to optimize the device for higher voltage (>5 kV and higher frequency (10 kHz are needed.

Process planning optimization on turning machine tool using a hybrid genetic algorithm with local search approach

Directory of Open Access Journals (Sweden)

Yuliang Su

2015-04-01

Full Text Available A turning machine tool is a kind of new type of machine tool that is equipped with more than one spindle and turret. The distinctive simultaneous and parallel processing abilities of turning machine tool increase the complexity of process planning. The operations would not only be sequenced and satisfy precedence constraints, but also should be scheduled with multiple objectives such as minimizing machining cost, maximizing utilization of turning machine tool, and so on. To solve this problem, a hybrid genetic algorithm was proposed to generate optimal process plans based on a mixed 0-1 integer programming model. An operation precedence graph is used to represent precedence constraints and help generate a feasible initial population of hybrid genetic algorithm. Encoding strategy based on data structure was developed to represent process plans digitally in order to form the solution space. In addition, a local search approach for optimizing the assignments of available turrets would be added to incorporate scheduling with process planning. A real-world case is used to prove that the proposed approach could avoid infeasible solutions and effectively generate a global optimal process plan.

Recent developments in turning hardened steels - A review

Science.gov (United States)

Sivaraman, V.; Prakash, S.

2017-05-01

Hard materials ranging from HRC 45 - 68 such as hardened AISI H13, AISI 4340, AISI 52100, D2 STL, D3 STEEL Steel etc., need super hard tool materials to machine. Turning of these hard materials is termed as hard turning. Hard turning makes possible direct machining of the hard materials and also eliminates the lubricant requirement and thus favoring dry machining. Hard turning is a finish turning process and hence conventional grinding is not required. Development of the new advanced super hard tool materials such as ceramic inserts, Cubic Boron Nitride, Polycrystalline Cubic Boron Nitride etc. enabled the turning of these materials. PVD and CVD methods of coating have made easier the production of single and multi layered coated tool inserts. Coatings of TiN, TiAlN, TiC, Al2O3, AlCrN over cemented carbide inserts has lead to the machining of difficult to machine materials. Advancement in the process of hard machining paved way for better surface finish, long tool life, reduced tool wear, cutting force and cutting temperatures. Micro and Nano coated carbide inserts, nanocomposite coated PCBN inserts, micro and nano CBN coated carbide inserts and similar developments have made machining of hardened steels much easier and economical. In this paper, broad literature review on turning of hardened steels including optimizing process parameters, cooling requirements, different tool materials etc., are done.

REACHING THE COMPUTING HELP DESK

CERN Multimedia

Miguel MARQUINA; Roger WOOLNOUGH; IT/User Support

1999-01-01

The way to contact the Computing Help Desk (also known as 'UCO' and hosted by IT Division as an entry point for general computing issues) has been streamlined in order to facilitate access to it. A new telephone line and email address have been set: Phone number: 78888Email: Helpdesk@cern.chhopefully easier to remember. Both entries are operational since last December. The previous number and email address remain valid and have been turned into aliases of the above. However we encourage using the latter at your convenience from now on. For additional information please see the article published at the CERN Computing Newsletter 233:http://consult.cern.ch/cnl/233/art_uco.htmlDo not hesitate to contact us (by email to User.Relations@cern.ch) for additional information or feedback regarding this matter.Nicole Cremel, Miguel Marquina, Roger WoolnoughIT/UserSupport

First turn simulations in the cooler synchrotron COSY

International Nuclear Information System (INIS)

Dinev, D.

1991-07-01

This paper is devoted to the first turn correction and related problems in particle accelerators of synchrotron type. The paper consists of two parts. The first part is a survey of the existing methods for first turn steering. The second part is entirely devoted to the first turn in the cooler synchrotron COSY which is under assembling in KFA-Julich, Germany. (orig.)

First turn around strategy for RHIC

International Nuclear Information System (INIS)

Milutinovic, J.; Ruggiero, A.G.

1991-01-01

The authors present a strategy for achieving the so-called first turn around in RHIC. The strategy is based on the same method proposed to correct a distorted closed orbit in RHIC, i.e. on a generalization of the local three-bump method. They found out that the method is very effective in passing the beam through a non-ideal, insufficiently known, machine. The perturbed lattice was generated by the code PATRIS, which was also adapted to control the newly developed software. In ten distributions of errors the software was capable of passing the beam through in 2-3 injection attempts, at full sextupole strength. It was also determined that once the beam makes the first turn around and all the correctors are energized, it stays in the machine for at least several hundred turns

Compensatory help-seeking in young and older adults: does seeking help, help?

Science.gov (United States)

Alea, Nicole; Cunningham, Walter R

2003-01-01

Asking other people for help is a compensatory behavior that may be useful across the life span to enhance functioning. Seventy-two older and younger men and women were either allowed to ask for help or were not allowed to ask for help while solving reasoning problems. Although the older adults answered fewer problems correctly, they did not seek additional help to compensate for their lower levels of performance. Younger adults sought more help. There were no age differences, however, in the types of help sought: indirect help (e.g., hints) was sought more often than direct help (e.g., asking for the answer). Exploratory analyses revealed that one's ability level was a better indicator than age of the utility of help-seeking. Findings are interpreted in the context of social and task-related influences on the use of help-seeking as a compensatory behavior across the life span.

Performance improvement studies for cutting tools with perforated surface in turning of titanium alloy

Directory of Open Access Journals (Sweden)

Charitha Rao

2018-01-01

Full Text Available In turning process, the cutting tool is essential for shaping materials. The cutting tools with various perforated surfaces help to increase the cutting tool life. Also, advances in CNC machining technologies have enhanced the productivity of machining process. One of the best or futuristic approaches in modern manufacturing engineering is the use of FEM Simulation for the metal cutting process. FEM simulation helps in understanding the metal deformation process and also helps in the reduction of experiments. The simulation helps the researchers to predict the major influencing cutting variable values without carrying out any experiment which is time-consuming and expensive. This research presents the simulation study of the performance of micro-hole patterned Polycrystalline Diamond cutting insert in machining Titanium alloy (Ti-6Al-4V. Micro-holes are drilled using Electrical Discharge Wire Drilling machine on the rake face of Polycrystalline Diamond (PCD cutting inserts. FEM analysis is carried out to evaluate the effect of perforations on the mechanical integrity of insert. The micro-hole patterned insert is modeled in PRO-E modeler and simulated using DEFORM-3D software. The effective stress, strain, and temperature distribution are analyzed and the results are compared with the normal insert.

Synthesis of conformationally restricted beta-turn mimics

NARCIS (Netherlands)

IJsselstijn, M.

2006-01-01

This thesis aims at developing methods for introducing conformational restriction in Beta-turns, the turn elements present in Beta-sheets. A conformationally restricted peptide might either be formed via incorporation of a bridging diamino acids in a growing peptide chain, or via covalent bond

Turn key contracts

International Nuclear Information System (INIS)

Feretic, D.

1975-01-01

The aim of this summary is to point out some specific areas which have to be covered in a turn-key contract and which are of primarily interest to the buyer of a nuclear plant. It will be assumed that the buyer is utility company in a developing country and a plant supplier a company in an industrial country. (orig./FW) [de

Salted neutrinos our favourite seasoning is helping to solve a great cosmic mystery

CERN Multimedia

Chown, M

2001-01-01

Underground salt domes could be the neutrino detectors of the future and help scientists to understand where high-energy cosmic rays originate. Neutrinos are extremely difficult to detect because they rarely interact with matter. Inside salt crystals though, neutrinos will occasionally strike an atomic nucleus and produce a shower of charged particles which in turn produces an intense burst of radio waves (1/2 page).

Stepping in Place While Voluntarily Turning Around Produces a Long-Lasting Posteffect Consisting in Inadvertent Turning While Stepping Eyes Closed

Directory of Open Access Journals (Sweden)

Stefania Sozzi

2016-01-01

Full Text Available Training subjects to step in place on a rotating platform while maintaining a fixed body orientation in space produces a posteffect consisting in inadvertent turning around while stepping in place eyes closed (podokinetic after-rotation, PKAR. We tested the hypothesis that voluntary turning around while stepping in place also produces a posteffect similar to PKAR. Sixteen subjects performed 12 min of voluntary turning while stepping around their vertical axis eyes closed and 12 min of stepping in place eyes open on the center of a platform rotating at 60°/s (pretests. Then, subjects continued stepping in place eyes closed for at least 10 min (posteffect. We recorded the positions of markers fixed to head, shoulder, and feet. The posteffect of voluntary turning shared all features of PKAR. Time decay of angular velocity, stepping cadence, head acceleration, and ratio of angular velocity after to angular velocity before were similar between both protocols. Both postrotations took place inadvertently. The posteffects are possibly dependent on the repeated voluntary contraction of leg and foot intrarotating pelvic muscles that rotate the trunk over the stance foot, a synergy common to both protocols. We propose that stepping in place and voluntary turning can be a scheme ancillary to the rotating platform for training body segment coordination in patients with impairment of turning synergies of various origin.

Train turn restrictions and line plan performance

DEFF Research Database (Denmark)

Burggraeve, Sofie; Bull, Simon Henry; Lusby, Richard Martin

In this paper we study the impact of the `turn conditions' in end stations on the performance of a line plan. If trains have to turn on their platform in an end station, the yoccupy the platform for several minutes. A more preferred option, from a timetabling point of view, would be that a train...... in a exible and large enough shunt. Starting from a given line plan, we compare two timetables, one where trains have to turn on their platform and one where trains can turn in a shunt. We evaluate the impact on the performance of the line plan by its feasibility for timetabling,the minimum overall buffer...... disappears from the platform in its end station after dwelling and only appears again when departing for a subsequent trip. In this case, the train will not interfere with other trains that dwell on the platform during the time between these events. However, this option is only possible if the train can stay...

Derrida’s Turn to Franciscan Philosophy

Directory of Open Access Journals (Sweden)

Marko Zlomislic

2008-12-01

Full Text Available Contemporary French philosophers such as Levinas, Bataille, and Derrida, along with the existentialists Kierkegaard and Nietzsche have all made use of Franciscan insights in order to safeguard the ipseity that cannot be reduced or totalized. In keeping with the taste that concerns me, this paper will examine Derrida’s turn to the poetry of Gerard Manley Hopkins and how such a turn may place Derrida within a catholic and Franciscan tradition.

RCRA Facility Investigation/Remedial Investigation Report with Baseline Risk Assessment for the Central Shops Burning/Rubble Pit (631-6G), Volume 1 Final

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The Burning/Rubble Pits at the Savannah River Site were usually shallow excavations approximately 3 to 4 meters in depth. Operations at the pits consisted of collecting waste on a continuous basis and burning on a monthly basis. The Central Shops Burning/Rubble Pit 631- 6G (BRP6G) was constructed in 1951 as an unlined earthen pit in surficial sediments for disposal of paper, lumber, cans and empty galvanized steel drums. The unit may have received other materials such as plastics, rubber, rags, cardboard, oil, degreasers, or drummed solvents. The BRP6G was operated from 1951 until 1955. After disposal activities ceased, the area was covered with soil. Hazardous substances, if present, may have migrated into the surrounding soil and/or groundwater. Because of this possibility, the United States Environmental Protection Agency (EPA) has designated the BRP6G as a Solid Waste Management Unit (SWMU) subject to the Resource Conservation Recovery Act/Comprehensive Environmental Response, Compensation and Liability Act (RCRA/CERCLA) process.

performance characteristics of a cam turning attachment

African Journals Online (AJOL)

Dr Obe

ABSTRACT. A modification of a cylindrical turning unit has been done to give a non- cylindrical turning attachment for production of irregular shapes, like cams on the lathe machine. To assess the performance of the attachment, cutting forces have been measured using a 'Sigma' Cutting Tool. Dynamometer. Furthermore ...

Turn over management and optimization of Shangdong nuclear power plant

International Nuclear Information System (INIS)

Zheng Tong

2014-01-01

After the equipments' installation is completed, the system will carry out commissioning tests. After commissioning work is completed, the system will be transferred to temporary operation. The plant buildings and structures will be transferred to operation for management and maintenance after civil work. The turn over work is an important part of the transfer from construction to operation. The article describes the significance of the nuclear power plant turn over work, turn over organization and management mode, the workflow of system turn over from construction to commissioning (TOP), turn over form commissioning to operation (TOTO), house hand over (HHO), building hand over (BHO) of Shandong Haiyang nuclear power plant, and analyze the current lack and future improvements of turn over work. Shandong Haiyang nuclear power plant will usher in the peak period of turn over work in 2013, fully aware of the importance of the turn over work, will play a key role in the long-term stable operation of the unit. (author)

Hatchability of chicken eggs as influenced by turning frequency in ...

African Journals Online (AJOL)

An experiment was conducted to determine the influence of turning frequency of chicken eggs on hatchability in hurricane lantern incubator. There were four treatments in which eggs were not turned in treatment one (control), those in treatment two were turned once daily (morning), treatment three turned twice daily ...

Precision lens assembly with alignment turning system

Science.gov (United States)

Ho, Cheng-Fang; Huang, Chien-Yao; Lin, Yi-Hao; Kuo, Hui-Jean; Kuo, Ching-Hsiang; Hsu, Wei-Yao; Chen, Fong-Zhi

2017-10-01

The poker chip assembly with high precision lens barrels is widely applied to ultra-high performance optical system. ITRC applies the poker chip assembly technology to the high numerical aperture objective lenses and lithography projection lenses because of its high efficiency assembly process. In order to achieve high precision lens cell for poker chip assembly, an alignment turning system (ATS) is developed. The ATS includes measurement, alignment and turning modules. The measurement module is equipped with a non-contact displacement sensor (NCDS) and an autocollimator (ACM). The NCDS and ACM are used to measure centration errors of the top and the bottom surface of a lens respectively; then the amount of adjustment of displacement and tilt with respect to the rotational axis of the turning machine for the alignment module can be determined. After measurement, alignment and turning processes on the ATS, the centration error of a lens cell with 200 mm in diameter can be controlled within 10 arcsec. Furthermore, a poker chip assembly lens cell with three sub-cells is demonstrated, each sub-cells are measured and accomplished with alignment and turning processes. The lens assembly test for five times by each three technicians; the average transmission centration error of assembly lens is 12.45 arcsec. The results show that ATS can achieve high assembly efficiency for precision optical systems.

Effectiveness evaluation of three RCRA caps at the Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

Shevenell, L.A. [Nevada Bureau of Mines and Geology, Reno, NV (United States); Goldstrand, P.M. [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Geological Sciences

1994-01-01

Because installation of Resource Conservation and Recovery Act (RCRA)- engineered caps is costly, it is prudent to evaluate the effectiveness of this procedure for hydrologically isolating contaminants. The objective for installation of five-part engineered caps at the Y-12 Plant was to (1) satisfy the regulatory compliance issues, (2) minimize the risk of direct contact with the wastes, and (3) reduce rainfall infiltration. Although the original objectives of installing the caps were not to alter groundwater flow, a potential effect of reducing infiltration is to minimize leaching, thus retarding groundwater contaminant migration from the site. Hence, cap effectiveness with respect to reduced groundwater contaminant migration is evaluated using groundwater data in this report. Based on the available data at the Y-12 capped areas, evaluation of cap effectiveness includes studying water level and chemical variability in nearby monitoring wells. Three caps installed during 1989 are selected for evaluation in this report. These caps are located in three significantly different hydrogeologic settings: overlying a karst aquifer (Chestnut Ridge Security Pits [CRSP]), overlying shales located on a hill slope (Oil Landfarm Waste Management Area [OLWMA]), and overlying shales in a valley floor which is a site of convergent groundwater flow (New Hope Pond [NHP]). Presumably, the caps have been effective in minimizing risk of direct contact with the wastes and halting direct rainfall infiltration into the sites over the extent of the capped areas, but no evidence is presented in this report to directly demonstrate this. The caps installed over the three sites appear to have had a minimal effect on groundwater contaminant migration from the respective sites. Following cap construction, no changes in the configuration of the water table were observed. Migration of contaminant plumes occurred at all three sites, apparently without regard to the timing of cap installation.

Annual Report RCRA Post-Closure Monitoring and Inspections for CAU 112: Area 23 Hazardous Waste Trenches, Nevada Test Site, Nevada, for the Period October 1999-October 2000

Energy Technology Data Exchange (ETDEWEB)

D. F. Emer

2001-03-01

This annual Neutron Soil Moisture Monitoring report provides an analysis and summary for site inspections, meteorological information, and neutron soil moisture monitoring data obtained at the Area 23 Hazardous Waste Trenches Resource Conservation and Recovery Act (RCRA) unit, located in Area 23 of the Nevada Test Site, Nye County, Nevada, during the October 1999-October 2000 period. Inspections of the Area 23 Hazardous Waste Trenches RCRA unit are conducted to determine and document the physical condition of the covers, facilities, and any unusual conditions that could impact the proper operation of the waste unit closure. Physical inspections of the closure were completed quarterly and indicated that the site is in good condition with no significant findings noted. An annual subsidence survey of the elevation markers was conducted in August 2000. There has been no subsidence at any of the markers since monitoring began seven years ago. The objective of the neutron logging program is to monitor the soil moisture conditions along 30 neutron access tubes and detect changes that maybe indicative of moisture movement at a point located directly beneath each trench. Precipitation for the period October 1999 through October 2000 was 10.44 centimeters (cm) (4.11 inches [in.]) (U.S. National Weather Service, 2000). The prior year annual rainfall (January 1999 through December 1999) was 10.13cm (3.99 in.). The highest 30-day cumulative rainfall occurred on March 8, 2000, with a total of 6.63 cm (2.61 in.). The heaviest daily precipitation occurred on February 23,2000, with a total of 1.70 cm (0.67 in.) falling in that 24-hour period. The recorded average annual rainfall for this site, from 1972 to January 1999, is 15.06 cm (5.93 in.). All monitored access tubes are within the compliance criteria of less than 5 percent residual volumetric moisture content at the compliance point directly beneath each respective trench. Soil conditions remain dry and stable underneath the

Structural and sequence features of two residue turns in beta-hairpins.

Science.gov (United States)

Madan, Bharat; Seo, Sung Yong; Lee, Sun-Gu

2014-09-01

Beta-turns in beta-hairpins have been implicated as important sites in protein folding. In particular, two residue β-turns, the most abundant connecting elements in beta-hairpins, have been a major target for engineering protein stability and folding. In this study, we attempted to investigate and update the structural and sequence properties of two residue turns in beta-hairpins with a large data set. For this, 3977 beta-turns were extracted from 2394 nonhomologous protein chains and analyzed. First, the distribution, dihedral angles and twists of two residue turn types were determined, and compared with previous data. The trend of turn type occurrence and most structural features of the turn types were similar to previous results, but for the first time Type II turns in beta-hairpins were identified. Second, sequence motifs for the turn types were devised based on amino acid positional potentials of two-residue turns, and their distributions were examined. From this study, we could identify code-like sequence motifs for the two residue beta-turn types. Finally, structural and sequence properties of beta-strands in the beta-hairpins were analyzed, which revealed that the beta-strands showed no specific sequence and structural patterns for turn types. The analytical results in this study are expected to be a reference in the engineering or design of beta-hairpin turn structures and sequences. © 2014 Wiley Periodicals, Inc.

Diamond turning machine controller implementation

Energy Technology Data Exchange (ETDEWEB)

Garrard, K.P.; Taylor, L.W.; Knight, B.F.; Fornaro, R.J.

1988-12-01

The standard controller for a Pnuemo ASG 2500 Diamond Turning Machine, an Allen Bradley 8200, has been replaced with a custom high-performance design. This controller consists of four major components. Axis position feedback information is provided by a Zygo Axiom 2/20 laser interferometer with 0.1 micro-inch resolution. Hardware interface logic couples the computers digital and analog I/O channels to the diamond turning machine`s analog motor controllers, the laser interferometer, and other machine status and control information. It also provides front panel switches for operator override of the computer controller and implement the emergency stop sequence. The remaining two components, the control computer hardware and software, are discussed in detail below.

Hatchability of chicken eggs as influenced by turning frequency in ...

African Journals Online (AJOL)

STORAGESEVER

2008-12-03

Dec 3, 2008 ... Brake (2004) confirmed that absence of turning resulted in presentation of the head in the small end of the egg. Egg turning facilitated the transfer of yolk nutrients to the embryo via the sub-embryonic fluid (Deeming, 1989a). With modern incubators, automatic turning devices allow the eggs to be turned on ...

The Effect of a Textured Insole on Symmetry of Turning

Directory of Open Access Journals (Sweden)

Etem Curuk

2018-01-01

Full Text Available Turning while walking is a common daily activity. Individuals with unilateral impairment frequently perform turns asymmetrically. The purpose of the study was to investigate the effect of a discomfort-inducing textured insole on symmetry of turning. Nine healthy individuals performed turns to the right while walking with no insole, immediately after the insole was inserted in the right shoe, and after walking for six minutes with the insole. The duration of turning, displacements of pelvic markers, and perceived level of discomfort were evaluated. Utilizing the insole was associated with the increased level of perceived discomfort (p<0.05. Moreover, using the insole was linked to changes in the displacement of two pelvic markers and larger asymmetry index while turning immediately after the insole was inserted in the right shoe as compared to no insole condition (p<0.05. The duration of right turning increased immediately after the insole was inserted (p<0.05 and after walking with the insole for six minutes. The results indicate that the textured insole creates asymmetry of turning in healthy individuals. The outcome provides a background for future studies focused on using a textured insole to minimize the asymmetry of turning commonly seen in individuals with unilateral impairment.

Characteristics of turn signal use at intersections in baseline naturalistic driving.

Science.gov (United States)

Sullivan, John M; Bao, Shan; Goudy, Roy; Konet, Heather

2015-01-01

The purpose of this study was to determine whether a driver's use of turn signals is sufficiently reliable to forecast a vehicle's future path around an intersection, when detailed information about the intersection is unavailable. Naturalistic observations of turn signal use among 108 drivers on surface streets were extracted from the baseline portion of a field operational test of a safety system. Left and right turns that resulted in heading changes of between 70 and 110° and turn radii between 18 and 90 m were selected from the dataset. The odds that a driver would signal a turn were modeled as a function of road type, turn direction, presence of a forward vehicle, whether the vehicle stopped before the turn, and driver age and gender. Overall, 25 percent of left turns and 29 percent of right turns were not signaled. Road type, turn direction, and presence of a forward vehicle were found to influence the odds that a turn is signaled, while gender and age of the driver did not. The results suggest that situational factors like road type and turn direction are more powerful predictors of whether a turn will be signaled than either age or gender. Signaling on major and minor surface roads was about 5 times more likely than on local roads and 1.5 times more likely when a forward vehicle was present, suggesting a possible effect of traffic volume. It was concluded that turn signal activation alone may be insufficiently reliable to forecast a driver's path. Copyright © 2014 Elsevier Ltd. All rights reserved.

Diamond turning of Si and Ge single crystals

Energy Technology Data Exchange (ETDEWEB)

Blake, P.; Scattergood, R.O.

1988-12-01

Single-point diamond turning studies have been completed on Si and Ge crystals. A new process model was developed for diamond turning which is based on a critical depth of cut for plastic flow-to-brittle fracture transitions. This concept, when combined with the actual machining geometry for single-point turning, predicts that {open_quotes}ductile{close_quotes} machining is a combined action of plasticity and fracture. Interrupted cutting experiments also provide a meant to directly measure the critical depth parameter for given machining conditions.

Turning is an important marker of balance confidence and walking limitation in persons with multiple sclerosis.

Directory of Open Access Journals (Sweden)

Gautam Adusumilli

Full Text Available The standard functional tool for gait assessment in multiple sclerosis (MS clinical trials has been the 25-Foot Timed Walk Test, a measure of gait speed. Straight-line gait assessment may not reflect adequately upon balance and coordination. Walking tests with turns may add additional information towards understanding gait and balance status, and be more reflective of ambulation in the community. Understanding the impact of turn parameters on patient-reported outcomes of balance and walking would help MS clinicians better formulate treatment plans for persons with gait limitations. In this study, ninety-one persons with MS (Expanded Disability Status Score; EDSS, range: 0-6.5 were enrolled in an initial cross-sectional study. Twenty-four subjects (EDSS, range:1.0-6.0 completed a follow-up visit an average of 12 months later. Spatiotemporal gait analysis was collected at both visits using APDM Opal wireless body-worn sensors while performing the Timed-Up-and-Go (TUG and 6-Minute Walk Test (6MWT. For both cross-sectional and longitudinal data, regression analyses determined the impact on the addition of turning parameters to stride velocity (SV, in the prediction of self-reported balance confidence (Activities-Specific Balance Confidence Scale (ABC and walking limitation (12-item Multiple Sclerosis Walking Scale (MSWS-12. The addition of 6MWT peak turn velocity (PTV to 6MWT SV increased the predictive power of the 6MWT for the ABC from 20% to 33%, and increased the predictive power from 28% to 41% for the MSWS-12. TUG PTV added to TUG SV also strengthened the relationship of the TUG for the ABC from 19% to 28%, and 27% to 36% for the MSWS-12. For those with 1 year follow-up, percent change in turn number of steps (TNS%Δ during the 6MWT added to 6MWT SV%Δ improved the modeling of ABC%Δ from 24% to 33%. 6MWT PTV%Δ added to 6MWT SV%Δ increased the predictive power of MSWS-12%Δ from 8% to 27%. Conclusively, turn parameters improved modeling of

ω-Turn: a novel β-turn mimic in globular proteins stabilized by main-chain to side-chain C−H···O interaction.

Science.gov (United States)

Dhar, Jesmita; Chakrabarti, Pinak; Saini, Harpreet; Raghava, Gajendra Pal Singh; Kishore, Raghuvansh

2015-02-01

Mimicry of structural motifs is a common feature in proteins. The 10-membered hydrogen-bonded ring involving the main-chain C − O in a β-turn can be formed using a side-chain carbonyl group leading to Asx-turn. We show that the N − H component of hydrogen bond can be replaced by a C(γ) -H group in the side chain, culminating in a nonconventional C − H···O interaction. Because of its shape this β-turn mimic is designated as ω-turn, which is found to occur ∼ three times per 100 residues. Three residues (i to i + 2) constitute the turn with the C − H···O interaction occurring between the terminal residues, constraining the torsion angles ϕi + 1, ψi + 1, ϕi + 2 and χ'1(i + 2) (using the interacting C(γ) atom). Based on these angles there are two types of ω-turns, each of which can be further divided into two groups. C(β) -branched side-chains, and Met and Gln have high propensities to occur at i + 2; for the last two residues the carbonyl oxygen may participate in an additional interaction involving the S and amino group, respectively. With Cys occupying the i + 1 position, such turns are found in the metal-binding sites. N-linked glycosylation occurs at the consensus pattern Asn-Xaa-Ser/Thr; with Thr at i + 2, the sequence can adopt the secondary structure of a ω-turn, which may be the recognition site for protein modification. Location between two β-strands is the most common occurrence in protein tertiary structure, and being generally exposed ω-turn may constitute the antigenic determinant site. It is a stable scaffold and may be used in protein engineering and peptide design. © 2014 Wiley Periodicals, Inc.

Borehole Data Package for Calendar Year 2001 RCRA Wells at Single-Shell Tank Waste Management Area U

International Nuclear Information System (INIS)

Horton, Duane G.

2002-01-01

This document provides information on the construction of three new RCRA wells at Waste Management Area U in September 2001. These wells were constructed to the specifications and requirements described in Washington Administrative Codes 173-160 and 173-303. Grab samples for geological description and archive were collected every 5 ft throughout the wells. Borehole and drill cuttings were monitored regularly for organic vapors and radionuclide contaminants. At well 299-W18-40, beta-gamma activity was found to be slightly above background at 120 ft below ground surface. All other measurements were below background. Cesium-137 was found at the ground surface and at 3 ft below ground surface (bgs). No other manmade contamination was found. At well 299-W19-44, no radionuclide contamination was found, but several intervals of high carbon monoxide were detected. Cesium-137 was detected at 3 ft bgs at 0.4 pCi/g. At well 299-W19-45, no radionuclide contamination was found, but several intervals of high carbon monoxide were detected. Cesium-137 was detected near the surface at 0.4 pCi/g. No other manmade radionuclide was detected. At well 299-W19-45, samples for geological description and archive were collected every 5 ft throughout the well. No contamination was noted. Cesium-137 was detected near the surface at 0.4 to 1.4 pCi/g. No other manmade radionuclide was detected

RCRA Facility Investigation report for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1991-09-01

WAG 6 comprises a shallow land burial facility used for disposal of low-level radioactive wastes (LLW) and, until recently, chemical wastes. As such, the site is subject to regulation under RCRA and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA). To comply with these regulations, DOE, in conjunction with the Environmental Protection Agency (EPA) and the Tennessee Department of Environment and Conservation (TDEC), developed a strategy for closure and remediation of WAG 6 by 1997. A key component of this strategy was to complete an RFI by September 1991. The primary objectives of the RFI were to evaluate the site's potential human health and environmental impacts and to develop a preliminary list of alternatives to mitigate these impacts. The WAG 6 one of three solid waste management units evaluated Oak Ridge National Laboratory (ORNL) existing waste disposal records and sampling data and performed the additional sampling and analysis necessary to: describe the nature and extent of contamination; characterize key contaminant transport pathways; and assess potential risks to human health and the environment by developing and evaluating hypothetical receptor scenarios. Estimated excess lifetime cancer risks as a result for exposure to radionuclides and chemicals were quantified for each hypothetical human receptor. For environmental receptors, potential impacts were qualitatively assessed. Taking into account regulatory requirements and base line risk assessment results, preliminary site closure and remediation objectives were identified, and a preliminary list of alternatives for site closure and remediation was developed

Beam polarization during a Siberian snake turn-on

International Nuclear Information System (INIS)

Anferov, Vladimir A.

1999-01-01

Installing Siberian snakes in a circular proton accelerator allows one to overcome all spin depolarizing resonances even at very high energies. However, Siberian snake application at low energies is technically rather difficult. Turning snake on at some energy during acceleration would allow using Siberian snakes even in rings with low injection energies. It is shown that the beam polarization would be preserved during the snake ramp, provided that the snake is turned on in more than ten turns, and the energy is set near a half-integer Gγ

A mediation model of professional psychological help seeking for suicide ideation among Asian American and white American college students.

Science.gov (United States)

Wong, Joel; Brownson, Chris; Rutkowski, Leslie; Nguyen, Chi P; Becker, Marty Swanbrow

2014-01-01

This study examined professional psychological help seeking among 1,045 white American and Asian American students from 70 U.S. colleges and universities who had seriously considered attempting suicide. The authors found that Asian American college students had lower rates of professional psychological help seeking for their suicide ideation than White American college students. Guided by social network perspectives on professional psychological help seeking, the authors also tested mediators of this racial disparity. Relative to white Americans, Asian Americans were advised by fewer people (especially fewer family members) to seek professional help, which was, in turn, associated with lower rates of professional psychological help seeking for suicide ideation. These findings underscore the importance of gatekeeping as a suicide prevention strategy for Asian American college students.

First turn around strategy for RHIC

International Nuclear Information System (INIS)

Milutinovic, J.; Ruggiero, A.G.

1991-06-01

We present a strategy for achieving the so-called first turn around in RHIC. The strategy is based on the same method we had proposed to correct a distorted closed orbit in RHIC, i.e., on a generalization of the local three-bump method. We found out that the method is very effective in passing the beam through a non-ideal, insufficiently known, machine. We tested that software on ten different Gaussian distributions of dominant orbit distorting lattice imperfections. The perturbed lattice was generated by the code PATRIS, which was also adapted to control the newly developed software. In all of the ten distributions the software was capable of passing the beam through in 2--3 injection attempts, at full sextupole strength. It was also determined that once the beam makes the first turn around and all the correctors are energized, it stays in the machine for at least several hundred turns that we had checked. The quality of the orbit, that was established in this way, was also found to be very good, i.e., the residual distortions at the places of large beta function were much less than one millimeter. With one or two monitors/correctors broken, the software established a first turn around without any extra difficulties. The quality of such orbit was, of course, somewhat degraded, especially around the broken devices. It was also observed that, in the process of actual closing, the beam develops free betatron oscillations in the amplitude range of 1--5 mm, which can be reduced either by changing the injection conditions to better match the actual closed orbit or by an appropriate damping device. The hardware proposed for RHIC is more than sufficient to meet the demands of the first turn controlling software. The maximum kick angle to be applied to the beam would require less than 2/3 of the corrector's top strength even at the top magnetic rigidity Bρ = 850 T·m, which means that the correctors will be performing an easy task at injection

Medium dependent dual turn on/turn off fluorescence sensing for Cu2 + ions using AMI/SDS assemblies

Science.gov (United States)

Gujar, Varsha B.; Ottoor, Divya

2017-02-01

Behavior of Amiloride (AMI) as a metal ion sensor in anionic surfactant assemblies of varying concentrations at different pH is depicted in this work. From a non-sensor fluorophore, AMI has been transformed in to a tunable fluorosensor for Cu2 + ions in various SDS concentrations. At premicellar concentration of SDS, ion-pair complex is expected to be formed between AMI and SDS due to electrostatic interactions between them. However at CMC concentrations of SDS, fluorescence intensity of AMI is greatly enhanced with red shift in emission, due to the incorporation of AMI molecule in the hydrophobic micellar interface. The behavior of metal sensing by AMI-SDS assemblies gives rise to several interesting observations. Micellation of SDS has been greatly enhanced by increasing copper ion concentrations, as these counter ions screens the charge on monomers of SDS which lead to the aggregation at premicellar concentrations only. Concentrations and pH dependent discrete trends of interactions between SDS-AMI and SDS-Cu2 + ions, have given tunable fluorescence responses (fluorescence turn on/turn off) of AMI for added Cu2 + ions. The electrostatic interaction between the metal cations and the anionic surfactants is the driving force for bringing the metal ions near to the vicinity of micelle where AMI resides. Thus, a comprehensive understanding of the mechanism related to the 'turn on-turn off' fluorescence response of AMI with respect to pH and SDS concentration for effective Cu2 + ion sensing is illustrated in this work.

Reconceptualizing Autonomy: A Relational Turn in Bioethics.

Science.gov (United States)

Jennings, Bruce

2016-05-01

History's judgment on the success of bioethics will not depend solely on the conceptual creativity and innovation in the field at the level of ethical and political theory, but this intellectual work is not insignificant. One important new development is what I shall refer to as the relational turn in bioethics. This development represents a renewed emphasis on the ideographic approach, which interprets the meaning of right and wrong in human actions as they are inscribed in social and cultural practices and in structures of lived meaning and interdependence; in an ideographic approach, the task of bioethics is to bring practice into theory, not the other way around. The relational turn in bioethics may profoundly affect the critical questions that the field asks and the ethical guidance it offers society, politics, and policy. The relational turn provides a way of correcting the excessive atomism of many individualistic perspectives that have been, and continue to be, influential in bioethics. Nonetheless, I would argue that most of the work reflecting the relational turn remains distinctively liberal in its respect for the ethical significance of the human individual. It moves away from individualism, but not from the value of individuality.In this review essay, I shall focus on how the relational turn has manifested itself in work on core concepts in bioethics, especially liberty and autonomy. Following a general review, I conclude with a brief consideration of two important recent books in this area: Jennifer Nedelsky's Law's Relations and Rachel Haliburton's Autonomy and the Situated Self. © 2016 The Hastings Center.

Using an information system to meet Hazardous Waste Management needs

International Nuclear Information System (INIS)

Stewart, J.J. Jr.; Howe, R.E.; Townsend, S.L.; Maloy, D.T.; Kochhar, R.K.

1995-02-01

Lawrence Livermore National Laboratory (LLNL) is a large quantity RCRA hazardous waste generator. LLNL also generates low level and transuranic radioactive waste that is managed in accordance with the Department of Energy (DOE) orders. The mixed low level and mixed transuranic waste generated must be managed to comply with both RCRA regulations and DOE orders. LLNL's hazardous and radioactive waste generation is comprised of 900 generators who contribute to nearly two hundred waste streams. LLNL has a permitted EPA treatment and storage (TSD) facility for handling RCRA hazardous waste that is operated by LLNL's Hazardous Waste Management (HWM) division. In HWM we have developed an information system, the Total Waste Management System (TWMS), to replace an inadequate ''cradle to grave'' tracking of all the waste types described above. The goals of this system are to facilitate the safe handling and storage of these hazardous wastes, provide compliance with the regulations and serve as an informational tool to help HWM manage and dispose of these wastes in a cost effective manner

Simulation of turn-by-turn passage of protons through the H-minus stripping foil in booster

Energy Technology Data Exchange (ETDEWEB)

Gardner, C. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2017-07-06

Equations for transverse emittance growth due to multiple passes of circulating proton beam through the H-minus stripping foil in Booster were developed in [1]. These were based on simple principles of statistics and simple assumptions about the initial distribution of particles incident on the foil. It was assumed there that the foil dimensions and position of the incoming beam are such that all particles hit the foil on every turn around the machine. In the present note we assume only that all incoming H-minus ions from Linac hit the foil and are stripped of their electrons. The resulting protons circulate indefinitely around the machine. Setups in which the foil width is reduced so that not all protons hit the foil on every turn are studied here by simulation. The aim is to determine the effectiveness of such setups in reducing the emittance growth of circulating proton beam during the injection of H-minus beam. The simulations also serve as a check of the equations developed in [1], and vice versa. The particulars of the simulation setup are given in Sections 1 through 11. Figures 1 through 12 show simulation results for the case in which all particles hit the foil on every turn. The results are in good agreement with those obtained from the equations of reference [1]. Figures 13 through 19 show simulation results for various setups in which the foil width is reduced. These results are summarized in Section 12. In all gures the horizontal axis gives the turn number. The unit of the vertical axis is micrometers ( m) in all plots of emittance.

Is It Cheating or Learning the Craft of Writing? Using Turnitin to Help Students Avoid Plagiarism

Science.gov (United States)

Graham-Matheson, Lynne; Starr, Simon

2013-01-01

Plagiarism is a growing problem for universities, many of which are turning to software detection for help in detecting and dealing with it. This paper explores issues around plagiarism and reports on a study of the use of Turnitin in a new university. The purpose of the study was to inform the senior management team about the plagiarism policy…

Postural hemodynamic changes after turning to prone position

Directory of Open Access Journals (Sweden)

Микола Віталійович Лизогуб

2015-03-01

Full Text Available Background of study. Prone position is one of the most complex positions for anesthesiologist as it is accompanied by several physiological changes that can lead to specific complications. Hemodynamic changes are most controversial.Aim of study was to establish hemodynamic changes in non-anaesthetized patients in prone position depending on body mass index.Material and methods. We examined central hemodynamics in 40 patients the day before surgery using thoracic rheography in supine position, in prone position 5 min after turning and in prone position 20 min after turning. Patients were divided into 2 groups according to body mass index (18-25 and 26-35.Results. Patients with normal body weight did not have any hemodynamic changes after turning to prone position. Patients with increased body weight had higher cardiac index. After turning to prone position obese patients’ cardiac output and cardiac index reduced 22% comparing with supine position. After 20 min in prone position these hemodynamic parameters were found to be reduced to the same level.Conclusion. Significant hemodynamic changes after turning from supine to prone position were revealed only in patients with increased body mass index. In these patients cardiac index in prone position was reduced by 22% comparing to supine position

1.06 μm 150 psec laser damage study of diamond turned, diamond turned/polished and polished metal mirrors

International Nuclear Information System (INIS)

Saito, T.T.; Milam, D.; Baker, P.; Murphy, G.

1975-01-01

Using a well characterized 1.06 μm 150 ps glass laser pulse the damage characteristics for diamond turned, diamond turned/ polished, and polished copper and silver mirrors less than 5 cm diameter were studied. Although most samples were tested with a normal angle of incidence, some were tested at 45 0 with different linear polarization showing an increase in damage threshold for S polarization. Different damage mechanisms observed will be discussed. Laser damage is related to residual surface influences of the fabrication process. First attempts to polish diamond turned surfaces resulted in a significant decrease in laser damage threshold. The importance of including the heat of fusion in the one dimensional heat analysis of the theoretical damage threshold and how close the samples came to the theoretical damage threshold is discussed. (auth)

Turning around Newton's Second Law

Science.gov (United States)

Goff, John Eric

2004-01-01

Conceptual and quantitative difficulties surrounding Newton's second law often arise among introductory physics students. Simply turning around how one expresses Newton's second law may assist students in their understanding of a deceptively simple-looking equation.

Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas

Science.gov (United States)

Central Ohio Turns Trash Into Natural Gas to someone by E-mail Share Alternative Fuels Data Center : Central Ohio Turns Trash Into Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Central Ohio Turns Trash Into Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Central Ohio Turns

Experimental investigation on hard turning of AISI 4340 steel using cemented coated carbide insert

Science.gov (United States)

Pradeep Kumar, J.; Kishore, K. P.; Ranjith Kumar, M.; Saran Karthick, K. R.; Vishnu Gowtham, S.

2018-02-01

Hard turning is a developing technology that offers many potential advantages compared to grinding, which remains the standard finishing process for critical hardened surfaces. In this work, an attempt has been made to experimentally investigate hard turning of AISI 4340 steel under wet and dry condition using cemented coated carbide insert. Hardness of the workpiece material is tested using Brinell and Rockwell hardness testers. CNC LATHE and cemented coated carbide inserts of designation CNMG 120408 are used for conducting experimental trials. Significant cutting parameters like cutting speed, feed rate and depth of cut are considered as controllable input parameters and surface roughness (Ra), tool wear are considered as output response parameters. Design of experiments is carried out with the help of Taguchi’s L9 orthogonal array. Results of response parameters like surface roughness and tool wear under wet and dry condition are analysed. It is found that surface roughness and tool wear are higher under dry machining condition when compared to wet machining condition. Feed rate significantly influences the surface roughness followed by cutting speed. Depth of cut significantly influences the tool wear followed by cutting speed.

The spatial turn and the scenario approach in flood risk management—Implementing the European Floods Directive in the Netherlands

Directory of Open Access Journals (Sweden)

Leon J. van Ruiten

2016-10-01

Full Text Available The European Floods Directive requires member states to prepare flood risk management plans for their river catchments. The first generation of those plans was just developed at the end of 2015; the next revision is due in 2021. The new instrument institutionalizes an ongoing paradigm shift from flood protection to flood risk management in Europe. It implies two major governance challenges: the spatial turn and the scenario approach. This contribution studies the implementation of these two governance challenges in the Netherlands, where the paradigm shift is considered to be advanced. Therefore, the spatial turn and the scenario approach are operationalized. The spatial turn consists of three aspects: space for the river, an integrated approach, and beyond structural measures. The scenario approach introduces the vulnerability of society in flood risk management. It is discussed how the challenges of spatial turn and the scenario approach—and thus the shift towards flood risk management—have an effect on the prevailing modes of governance in water management in the Netherlands. This helps understand the tensions and frictions with implementing the plans, but also illustrates how the European Floods Directive institutionalizes the shift towards flood risk management. The analytical scheme, consists mainly of operationalization, can foster future comparative studies with other countries and over time, to trace the changes in approaches to flood risks in Europe.

Proposed modifications to the RCRA post-closure permit for the Upper East Fork Poplar Creek Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

This report presents proposed modifications to the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Upper East Fork Poplar Creek Hydrogeologic Regime (permit number TNHW-088, EPA ID No. TN3 89 009 0001). The modifications are proposed to: (1) revise the current text for two of the Permit Conditions included in Permit Section II - General Facility Conditions, and (2) update the PCP with revised versions of the Y-12 Plant Groundwater Protection Program (GWPP) technical field procedures included in several of the Permit Attachments. The updated field procedures and editorial revisions are Class 1 permit modifications, as specified in Title 40, Code of Federal Regulations (CFR) {section}270.42; Appendix I - Classification of Permit Modifications. These modifications are summarized below.

Proposed modifications to the RCRA post-closure permit for the Upper East Fork Poplar Creek Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1997-05-01

This report presents proposed modifications to the Resource Conservation and Recovery Act (RCRA) Post-Closure Permit (PCP) for the Upper East Fork Poplar Creek Hydrogeologic Regime (permit number TNHW-088, EPA ID No. TN3 89 009 0001). The modifications are proposed to: (1) revise the current text for two of the Permit Conditions included in Permit Section II - General Facility Conditions, and (2) update the PCP with revised versions of the Y-12 Plant Groundwater Protection Program (GWPP) technical field procedures included in several of the Permit Attachments. The updated field procedures and editorial revisions are Class 1 permit modifications, as specified in Title 40, Code of Federal Regulations (CFR) section 270.42; Appendix I - Classification of Permit Modifications. These modifications are summarized below

Minimum-fuel turning climbout and descent guidance of transport jets

Science.gov (United States)

Neuman, F.; Kreindler, E.

1983-01-01

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Characterization of Vadose Zone Sediment: RCRA Borehole 299-E33-338 Located Near the B-BX-BY Waste Management Area

Energy Technology Data Exchange (ETDEWEB)

Lindenmeier, Clark W.; Serne, R. Jeffrey; Bjornstad, Bruce N.; Gee, Glendon W.; Schaef, Herbert T.; Lanigan, David C.; Lindberg, Michael J.; Clayton, Ray E.; Legore, Virginia L.; Kutnyakov, Igor V.; Baum, Steven R.; Geiszler, Keith N.; Brown, Christopher F.; Valenta, Michelle M.; Vickerman, Tanya S.; Royack, Lisa J.

2008-09-11

This report was revised in September 2008 to remove acid-extractable sodium data from Table 4.8. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in June 2003. The overall goals of the of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., are: 1) to define risks from past and future single-shell tank farm activities, 2) to identify and evaluate the efficacy of interim measures, and 3) to aid via collection of geotechnical information and data, future decisions that must be made by the U.S. Department of Energy (DOE) regarding the near-term operations, future waste retrieval, and final closure activities for the single-shell tank waste management areas. For a more complete discussion of the goals of the Tank Farm Vadose Zone Project, see the overall work plan, Phase 1 RCRA Facility Investigation/Corrective Measures Study Work Plan for the Single-Shell Tank Waste Management Areas (DOE 1999). Specific details on the rationale for activities performed at the B-BX-BY tank farm waste management area are found in CH2M HILL (2000).

RCRA closure plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1992-11-01

The Bear Creek Burial Grounds (BCBG) are located on the southwest flank of Pine Ridge ∼1.5 miles west of the Oak Ridge Y-12 Plant in Bear Creek Valley. This facility consists of several contiguous disposal sites identified as Burial Grounds A, B, C, and D. Each burial site consists of a series of trenches used for disposal of solid wastes and, in some cases, liquid wastes. Initially, the RCRA Closure/Postclosure plan for the BCBG was intended to apply to A Area, C-West, B Area, and the walk-in pits for BCBG. However, a plan was provided to include the B Area in the walk-in pits so that both areas cold be closed under one cap. The closure plan for B Area and the walk-in pits is presented in this document. The actual quantity and identity of materials is uncertain. The largest volume of material disposed in BCBG consists of uranium-contaminated industrial trash (paper, wood, steel, glass, and rubble)

Sequence-specific unusual (1-->2)-type helical turns in alpha/beta-hybrid peptides.

Science.gov (United States)

Prabhakaran, Panchami; Kale, Sangram S; Puranik, Vedavati G; Rajamohanan, P R; Chetina, Olga; Howard, Judith A K; Hofmann, Hans-Jörg; Sanjayan, Gangadhar J

2008-12-31

This article describes novel conformationally ordered alpha/beta-hybrid peptides consisting of repeating l-proline-anthranilic acid building blocks. These oligomers adopt a compact, right-handed helical architecture determined by the intrinsic conformational preferences of the individual amino acid residues. The striking feature of these oligomers is their ability to display an unusual periodic pseudo beta-turn network of nine-membered hydrogen-bonded rings formed in the forward direction of the sequence by 1-->2 amino acid interactions both in solid-state and in solution. Conformational investigations of several of these oligomers by single-crystal X-ray diffraction, solution-state NMR, and ab initio MO theory suggest that the characteristic steric and dihedral angle restraints exerted by proline are essential for stabilizing the unusual pseudo beta-turn network found in these oligomers. Replacing proline by the conformationally flexible analogue alanine (Ala) or by the conformationally more constrained alpha-amino isobutyric acid (Aib) had an adverse effect on the stabilization of this structural architecture. These findings increase the potential to design novel secondary structure elements profiting from the steric and dihedral angle constraints of the amino acid constituents and help to augment the conformational space available for synthetic oligomer design with diverse backbone structures.

A turn-on supramolecular fluorescent probe for sensing benzimidazole fungicides and its application in living cell imaging

Science.gov (United States)

Tang, Qing; Zhang, Jing; Sun, Tao; Wang, Cheng-Hui; Huang, Ying; Zhou, Qingdi; Wei, Gang

2018-02-01

A cucurbit[8]uril-based turn-on supramolecular fluorescent probe between cucurbit[8]uril (Q[8]) and pyronine Y (PyY) (designated 2PyY@Q[8]) in acidic aqueous solution showed a remarkable fluorescence 'turn-on' response to benzimidazole fungicides such as thiabendazole, fuberidazole and carbendazim. The 2PyY@Q[8] fluorescent probe can be used to detect benzimidazole fungicides with high sensitivity and selectivity with a detection limit of 10- 8 mol/L. A good linear relationship of emission intensity at 580 nm for benzimidazole fungicides at concentrations of 0.4-5.0 μmol/L was observed. The proposed sensing mechanism was investigated using 1H NMR spectroscopy combined with density functional theory calculations at the B3LYP/6-31G(d) level. The cell imaging study showed that the 2PyY@Q[8] complex could be used to image benzimidazole fungicide in prostate cancer (PC3) cells, which may help to elucidate relevant biological processes at the molecular level.

History of Education in Canada: Historiographic "Turns" and Widening Horizons

Science.gov (United States)

Bruno-Jofré, Rosa

2014-01-01

This paper explores major historiographic "turns" in history of education with a focus, although not exclusively, on English-speaking Canada. It addresses the transformative intellectual impact of the turn toward social history on the history of education, the impact of cultural history and the linguistic turn, the reception of Michel…

Turn-taking cue delays in human-robot communication

NARCIS (Netherlands)

Cuijpers, R. H.; Van Den Goor, V. J.P.

2017-01-01

Fluent communication between a human and a robot relies on the use of effective turn-taking cues. In human speech staying silent after a sequence of utterances is usually accompanied by an explicit turnyielding cue to signal the end of a turn. Here we study the effect of the timing of four

Human Rights Education and the Post Secular Turn

Science.gov (United States)

Bowie, Bob

2012-01-01

This article questions whether human rights education (HRE) scholarship is responding adequately to the post secular turn in thinking about the place and nature of religion in society. Here the post secular turn is used to describe the discrediting of secularisation theory, the recognition of religion as an enduring and pervasive global cultural…

Model-independent analysis of the Fermilab Tevatron turn-by-turn beam position monitor measurements

Science.gov (United States)

Petrenko, A. V.; Valishev, A. A.; Lebedev, V. A.

2011-09-01

Coherent transverse beam oscillations in the Tevatron were analyzed with the model-independent analysis (MIA) technique. This allowed one to obtain the model-independent values of coupled betatron amplitudes, phase advances, and dispersion function around the ring from a single dipole kick measurement. In order to solve the MIA mode mixing problem which limits the accuracy of determination of the optical functions, we have developed a new technique of rotational MIA mode untangling. The basic idea is to treat each beam position monitor (BPM) as two BPMs separated in a ring by exactly one turn. This leads to a simple criterion of MIA mode separation: the betatron phase advance between any BPM and its counterpart shifted by one turn should be equal to the betatron tune and therefore should not depend on the BPM position in the ring. Furthermore, we describe a MIA-based technique to locate vibrating magnets in a storage ring.

Model-independent analysis of the Fermilab Tevatron turn-by-turn beam position monitor measurements

Directory of Open Access Journals (Sweden)

A. V. Petrenko

2011-09-01

Full Text Available Coherent transverse beam oscillations in the Tevatron were analyzed with the model-independent analysis (MIA technique. This allowed one to obtain the model-independent values of coupled betatron amplitudes, phase advances, and dispersion function around the ring from a single dipole kick measurement. In order to solve the MIA mode mixing problem which limits the accuracy of determination of the optical functions, we have developed a new technique of rotational MIA mode untangling. The basic idea is to treat each beam position monitor (BPM as two BPMs separated in a ring by exactly one turn. This leads to a simple criterion of MIA mode separation: the betatron phase advance between any BPM and its counterpart shifted by one turn should be equal to the betatron tune and therefore should not depend on the BPM position in the ring. Furthermore, we describe a MIA-based technique to locate vibrating magnets in a storage ring.

Turning goals into results: the power of catalytic mechanisms.

Science.gov (United States)

Collins, J

1999-01-01

Most executives have a big, hairy, audacious goal. They write vision statements, formalize procedures, and develop complicated incentive programs--all in pursuit of that goal. In other words, with the best of intentions, they install layers of stultifying bureaucracy. But it doesn't have to be that way. In this article, Jim Collins introduces the catalytic mechanism, a simple yet powerful managerial tool that helps translate lofty aspirations into concrete reality. Catalytic mechanisms are the crucial link between objectives and performance; they are a galvanizing, nonbureaucratic means to turn one into the other. What's the difference between catalytic mechanisms and most traditional managerial controls? Catalytic mechanisms share five characteristics. First, they produce desired results in unpredictable ways. Second, they distribute power for the benefit of the overall system, often to the discomfort of those who traditionally hold power. Third, catalytic mechanisms have teeth. Fourth, they eject "viruses"--those people who don't share the company's core values. Finally, they produce an ongoing effect. Catalytic mechanisms are just as effective for reaching individual goals as they are for corporate ones. To illustrate how catalytic mechanisms work, the author draws on examples of individuals and organizations that have relied on such mechanisms to achieve their goals. The same catalytic mechanism that works in one organization, however, will not necessarily work in another. Catalytic mechanisms must be tailored to specific goals and situations. To help readers get started, the author offers some general principles that support the process of building catalytic mechanisms effectively.

Compensations for increased rotational inertia during human cutting turns.

Science.gov (United States)

Qiao, Mu; Brown, Brian; Jindrich, Devin L

2014-02-01

Locomotion in a complex environment is often not steady state, but unsteady locomotion (stability and maneuverability) is not well understood. We investigated the strategies used by humans to perform sidestep cutting turns when running. Previous studies have argued that because humans have small yaw rotational moments of inertia relative to body mass, deceleratory forces in the initial velocity direction that occur during the turning step, or 'braking' forces, could function to prevent body over-rotation during turns. We tested this hypothesis by increasing body rotational inertia and testing whether braking forces during stance decreased. We recorded ground reaction force and body kinematics from seven participants performing 45 deg sidestep cutting turns and straight running at five levels of body rotational inertia, with increases up to fourfold. Contrary to our prediction, braking forces remained consistent at different rotational inertias, facilitated by anticipatory changes to body rotational speed. Increasing inertia revealed that the opposing effects of several turning parameters, including rotation due to symmetrical anterior-posterior forces, result in a system that can compensate for fourfold changes in rotational inertia with less than 50% changes to rotational velocity. These results suggest that in submaximal effort turning, legged systems may be robust to changes in morphological parameters, and that compensations can involve relatively minor adjustments between steps to change initial stance conditions.

Statistical methods for determination of background levels for naturally occuring radionuclides in soil at a RCRA facility

International Nuclear Information System (INIS)

Guha, S.; Taylor, J.H.

1996-01-01

It is critical that summary statistics on background data, or background levels, be computed based on standardized and defensible statistical methods because background levels are frequently used in subsequent analyses and comparisons performed by separate analysts over time. The final background for naturally occurring radionuclide concentrations in soil at a RCRA facility, and the associated statistical methods used to estimate these concentrations, are presented. The primary objective is to describe, via a case study, the statistical methods used to estimate 95% upper tolerance limits (UTL) on radionuclide background soil data sets. A 95% UTL on background samples can be used as a screening level concentration in the absence of definitive soil cleanup criteria for naturally occurring radionuclides. The statistical methods are based exclusively on EPA guidance. This paper includes an introduction, a discussion of the analytical results for the radionuclides and a detailed description of the statistical analyses leading to the determination of 95% UTLs. Soil concentrations reported are based on validated data. Data sets are categorized as surficial soil; samples collected at depths from zero to one-half foot; and deep soil, samples collected from 3 to 5 feet. These data sets were tested for statistical outliers and underlying distributions were determined by using the chi-squared test for goodness-of-fit. UTLs for the data sets were then computed based on the percentage of non-detects and the appropriate best-fit distribution (lognormal, normal, or non-parametric). For data sets containing greater than approximately 50% nondetects, nonparametric UTLs were computed

Characterization of jellyfish turning using 3D-PTV

Science.gov (United States)

Xu, Nicole; Dabiri, John

2017-11-01

Aurelia aurita are oblate, radially symmetric jellyfish that consist of a gelatinous bell and subumbrellar muscle ring, which contracts to provide motive force. Swimming is typically modeled as a purely vertical motion; however, asymmetric activations of swim pacemakers (sensory organs that innervate the muscle at eight locations around the bell margin) result in turning and more complicated swim behaviors. More recent studies have examined flow fields around turning jellyfish, but the input/output relationship between locomotive controls and swim trajectories is unclear. To address this, bell kinematics for both straight swimming and turning are obtained using 3D particle tracking velocimetry (3D-PTV) by injecting biocompatible elastomer tags into the bell, illuminating the tank with ultraviolet light, and tracking the resulting fluorescent particles in a multi-camera setup. By understanding these kinematics in both natural and externally controlled free-swimming animals, we can connect neuromuscular control mechanisms to existing flow measurements of jellyfish turning for applications in designing more energy efficient biohybrid robots and underwater vehicles. NSF GRFP.

Zigzag turning preference of freely crawling cells.

Directory of Open Access Journals (Sweden)

Taeseok Daniel Yang

Full Text Available The coordinated motion of a cell is fundamental to many important biological processes such as development, wound healing, and phagocytosis. For eukaryotic cells, such as amoebae or animal cells, the cell motility is based on crawling and involves a complex set of internal biochemical events. A recent study reported very interesting crawling behavior of single cell amoeba: in the absence of an external cue, free amoebae move randomly with a noisy, yet, discernible sequence of 'run-and-turns' analogous to the 'run-and-tumbles' of swimming bacteria. Interestingly, amoeboid trajectories favor zigzag turns. In other words, the cells bias their crawling by making a turn in the opposite direction to a previous turn. This property enhances the long range directional persistence of the moving trajectories. This study proposes that such a zigzag crawling behavior can be a general property of any crawling cells by demonstrating that 1 microglia, which are the immune cells of the brain, and 2 a simple rule-based model cell, which incorporates the actual biochemistry and mechanics behind cell crawling, both exhibit similar type of crawling behavior. Almost all legged animals walk by alternating their feet. Similarly, all crawling cells appear to move forward by alternating the direction of their movement, even though the regularity and degree of zigzag preference vary from one type to the other.

Effects of turning and through lane sharing on traffic performance at intersections

Science.gov (United States)

Li, Xiang; Sun, Jian-Qiao

2016-02-01

Turning vehicles strongly influence traffic flows at intersections. Effective regulation of turning vehicles is important to achieve better traffic performance. This paper studies the impact of lane sharing and turning signals on traffic performance at intersections by using cellular automata. Both right-turn and left-turn lane sharing are studied. Interactions between vehicles and pedestrians are considered. The transportation efficiency, road safety and energy economy are the traffic performance metrics. Extensive simulations are carried out to study the traffic performance indices. It is observed that shared turning lanes and permissive left-turn signal improve the transportation efficiency and reduce the fuel consumption in most cases, but the safety is usually sacrificed. It is not always beneficial for the through vehicles when they are allowed to be in the turning lanes.

Effect of cutting edge radius on surface roughness in diamond tool turning of transparent MgAl2O4 spinel ceramic

Science.gov (United States)

Yue, Xiaobin; Xu, Min; Du, Wenhao; Chu, Chong

2017-09-01

Transparent magnesium aluminate spinel (MgAl2O4) ceramic is one of an important optical materials. However, due to its pronounced hardness and brittleness, the optical machining of this material is very difficult. Diamond turning has advantages over the grinding process in flexibility and material removal rate. However, there is a lack of research that could support the use of diamond turning technology in the machining of MgAl2O4 spinel ceramic. Using brittle-ductile transition theory of brittle material machining, this work provides critical information that may help to realize ductile-regime turning of MgAl2O4 spinel ceramic. A characterization method of determination the cutting edge radius is introduced here. Suitable diamond tools were measured for sharpness and then chosen from a large number of candidate tools. The influence of rounded cutting edges on surface roughness of the MgAl2O4 spinel ceramic is also investigated. These results indicate that surface quality of MgAl2O4 spinel is relate to the radius of diamond tool's cutting edge, cutting speed, and feed rate. Sharp diamond tools (small radius of cutting edge) facilitated ductile-regime turning of MgAl2O4 spinel and shows great potential to reduce surface roughness and produce smoother final surface.

Phenomenology and the Empirical Turn

NARCIS (Netherlands)

Zwier, Jochem; Blok, Vincent; Lemmens, Pieter

2016-01-01

This paper provides a phenomenological analysis of postphenomenological philosophy of technology. While acknowledging that the results of its analyses are to be recognized as original, insightful, and valuable, we will argue that in its execution of the empirical turn, postphenomenology forfeits

Options for improving hazardous waste cleanups using risk-based criteria

International Nuclear Information System (INIS)

Elcock, D.

1995-01-01

This paper explores how risk- and technology-based criteria are currently used in the RCRA and CERCLA cleanup programs. It identifies ways in which risk could be further incorporated into RCRA and CERCLA cleanup requirements and the implications of risk-based approaches. The more universal use of risk assessment as embodied in the risk communication and risk improvement bills before Congress is not addressed. Incorporating risk into the laws and regulations governing hazardous waste cleanup, will allow the use of the best scientific information available to further the goal of environmental protection in the United States while containing costs. and may help set an example for other countries that may be developing cleanup programs, thereby contributing to enhanced global environmental management

Help Helps, but Only so Much: Research on Help Seeking with Intelligent Tutoring Systems

Science.gov (United States)

Aleven, Vincent; Roll, Ido; McLaren, Bruce M.; Koedinger, Kenneth R.

2016-01-01

Help seeking is an important process in self-regulated learning (SRL). It may influence learning with intelligent tutoring systems (ITSs), because many ITSs provide help, often at the student's request. The Help Tutor was a tutor agent that gave in-context, real-time feedback on students' help-seeking behavior, as they were learning with an ITS.…

Self-Concealment Mediates the Relationship Between Perfectionism and Attitudes Toward Seeking Psychological Help Among Adolescents.

Science.gov (United States)

Abdollahi, Abbas; Hosseinian, Simin; Beh-Pajooh, Ahmad; Carlbring, Per

2017-01-01

One of the biggest barriers in treating adolescents with mental health problems is their refusing to seek psychological help. This study was designed to examine the relationships between two forms of perfectionism, self-concealment and attitudes toward seeking psychological help and to test the mediating role of self-concealment in the relationship between perfectionism and attitudes toward seeking psychological help among Malaysian high school students. The participants were 475 Malaysian high school students from four high schools in Kuala Lumpur, Malaysia. Structural equation modelling results indicated that high school students with high levels of socially prescribed perfectionism, high levels of self-concealment, and low levels of self-oriented perfectionism reported negative attitudes toward seeking psychological help. Bootstrapping analysis showed that self-concealment emerged as a significant, full mediator in the link between socially prescribed perfectionism and attitudes toward seeking psychological help. Moderated mediation analysis also examined whether the results generalized across men and women. The results revealed that male students with socially prescribed perfectionism are more likely to engage in self-concealment, which in turn, leads to negative attitudes toward seeking psychological help more than their female counterparts. The results suggested that students high in socially prescribed perfectionism were more likely to engage in self-concealment and be less inclined to seek psychological help.

Transparent lattice characterization with gated turn-by-turn data of diagnostic bunch train

Science.gov (United States)

Li, Yongjun; Cheng, Weixing; Ha, Kiman; Rainer, Robert

2017-11-01

Methods of characterization of a storage ring's lattice have traditionally been intrusive to routine operations. More importantly, the lattice seen by particles can drift with the beam current due to collective effects. To circumvent this, we have developed a novel approach for dynamically characterizing a storage ring's lattice that is transparent to operations. Our approach adopts a dedicated filling pattern which has a short, separate diagnostic bunch train (DBT). Through the use of a bunch-by-bunch feedback system, the DBT can be selectively excited on demand. Gated functionality of a beam position monitor system is capable of collecting turn-by-turn data of the DBT, from which the lattice can then be characterized after excitation. As the DBT comprises only about one percent of the total operational bunches, the effects of its excitation are negligible to users. This approach allows us to localize the distributed quadrupolar wakefields generated in the storage ring vacuum chamber during beam accumulation. While effectively transparent to operations, our approach enables us to dynamically control the beta beat and phase beat, and unobtrusively optimize performance of the National Synchrotron Light Source-II accelerator during routine operations.

Density of Plutonium Turnings Generated from Machining Activities

Energy Technology Data Exchange (ETDEWEB)

Gonzales, John Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Vigil, Duane M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jachimowski, Thomas A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Archuleta, Alonso [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Arellano, Gerald Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Melton, Vince Lee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-10-20

The purpose of this project was to determine the density of plutonium (Pu) turnings generated from the range of machining activities, using both surrogate material and machined Pu turnings. Verify that 500 grams (g) of plutonium will fit in a one quart container using a surrogate equivalent volume and that 100 grams of Pu will fit in a one quart Savy container.

Prediction and analysis of beta-turns in proteins by support vector machine.

Science.gov (United States)

Pham, Tho Hoan; Satou, Kenji; Ho, Tu Bao

2003-01-01

Tight turn has long been recognized as one of the three important features of proteins after the alpha-helix and beta-sheet. Tight turns play an important role in globular proteins from both the structural and functional points of view. More than 90% tight turns are beta-turns. Analysis and prediction of beta-turns in particular and tight turns in general are very useful for the design of new molecules such as drugs, pesticides, and antigens. In this paper, we introduce a support vector machine (SVM) approach to prediction and analysis of beta-turns. We have investigated two aspects of applying SVM to the prediction and analysis of beta-turns. First, we developed a new SVM method, called BTSVM, which predicts beta-turns of a protein from its sequence. The prediction results on the dataset of 426 non-homologous protein chains by sevenfold cross-validation technique showed that our method is superior to the other previous methods. Second, we analyzed how amino acid positions support (or prevent) the formation of beta-turns based on the "multivariable" classification model of a linear SVM. This model is more general than the other ones of previous statistical methods. Our analysis results are more comprehensive and easier to use than previously published analysis results.

Effects of dual task on turning ability in stroke survivors and older adults.

Science.gov (United States)

Hollands, K L; Agnihotri, D; Tyson, S F

2014-09-01

Turning is an integral component of independent mobility in which stroke survivors frequently fall. This study sought to measure the effects of competing cognitive demands on the stepping patterns of stroke survivors, compared to healthy age-match adults, during turning as a putative mechanism for falls. Walking and turning (90°) was assessed under single (walking and turning alone) and dual task (subtracting serial 3s while walking and turning) conditions using an electronic, pressure-sensitive walkway. Dependent measures were time to turn, variability in time to turn, step length, step width and single support time during three steps of the turn. Turning ability in single and dual task conditions was compared between stroke survivors (n=17, mean ± SD: 59 ± 113 months post-stroke, 64 ± 10 years of age) and age-matched healthy counterparts (n=15). Both groups took longer, were more variable, tended to widen the second step and, crucially, increased single support time on the inside leg of the turn while turning and distracted. Increased single support time during turning may represent biomechanical mechanism, within stepping patterns of turning under distraction, for increased risk of falls for both stroke survivors and older adults. Crown Copyright © 2014. Published by Elsevier B.V. All rights reserved.

Hydrodynamics of Turning Flocks

OpenAIRE

Yang, Xingbo; Marchetti, M. Cristina

2014-01-01

We present a hydrodynamic model of flocking that generalizes the familiar Toner-Tu equations to incorporate turning inertia of well-polarized flocks. The continuum equations controlled by only two dimensionless parameters, orientational inertia and alignment strength, are derived by coarse graining the inertial spin model recently proposed by Cavagna et al. The interplay between orientational inertia and bend elasticity of the flock yields anisotropic spin waves that mediate the propagation o...

A prospective observational study of ICU patient position and frequency of turning.

Science.gov (United States)

Goldhill, D R; Badacsonyi, A; Goldhill, A A; Waldmann, C

2008-05-01

Positioning and turning critically ill patients may be beneficial but there are little data on current practice. We prospectively recorded patient position every hour over two separate days in 40 British intensive care units and analysed 393 sets of observation. Five patients were prone at any time and 3.8% (day 1) and 5% (day 2) were on rotating beds. Patients were on their back for 46.1% of observations, turned left for 28.4% and right for 25.5%, and head up for 97.4%. A turn was defined as a change between on back, turned left or turned right. The average time (SD) between turns was 4.85 (3.3) h. There was no significant association between the average time between turns and age, weight, height, gender, respiratory diagnosis, intubated and ventilated, sedation score, day of week or nurse:patient ratio. There was a significant difference between hospitals in the frequency with which patients were turned.

TOWARDS COLLABORATION BETWEEN PUBLIC WELFARE AGENCIES AND MASS ENTERTAINMENT MEDIA TO BRING ABOUT A TURNING POINT STAGE IN THE LIVES OF BATTERED WOMEN

Directory of Open Access Journals (Sweden)

Nourit Segev

2010-06-01

Full Text Available This article examines the promoting and impeding factors that advance the turning point in thelives of battered women. The subject is important because of the contribution of the turning pointstage to the ability of women to leave the violent relationship and the way in which the publicwelfare agencies become involved in order to help the victim to advance towards the turning point.The article also reviews the influence of the entertainment media in shaping the positions of thepublic regarding marital violence, the presentation of battered women in the media, and theconnection between their media presentation and their advancement towards the turning point inreality.The research is based on a combination of qualitative and quantitative data, and focuses on contentanalysis. The qualitative content analysis included 40 journal articles, 1 documentary film and onedrama series, the personal interviews included 8 social workers and 6 journalists, and the focusgroup included 8 battered women. The findings indicate an awareness of battered women in thevarious media, and of a gap between the perception of social workers and the journalists regardingthe role of the media in raising social problems.The article calls for cooperation between the media and the professionals in order to construct messages of empowerment that will enable women to advance towards the turning point in theirlives.

200-BP-11 operable unit and 216-B-3 main pond work/closure plan, Hanford Site, Richland, Washington. Volume 1: Field investigation and sampling strategy

International Nuclear Information System (INIS)

1994-09-01

This document coordinates a Resource Conservation and Recovery Act (RCRA) past-practice work plan for the 200-BP-11 Operable Unit and a RCRA closure/postclosure plan for the 216-B-3 Main Pond and 216-B-3-3 Ditch [treatment, storage, and/or disposal (TSD) unit]. Both RCRA TSD and past-practice waste management units are contained within the 200-BP-11 Operable Unit. The 200-BP-11 Operable Unit is a source operable unit located on the east side of the B Plant Source Aggregate Area in the 200 East Area of the Hanford Site. The operable unit lies just east of the 200 East Area perimeter fence and encompass approximately 476 hectares (1,175 acres). Source operable units include waste management units that are potential sources of radioactive and/or hazardous substance contamination. Source waste management units are categorized in the Hanford Federal Facility Agreement and Consent Order as either RCRA TSD, RCRA past-practice, or Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) past-practice. As listed below and in the Tri-Party Agreement, the 200-BP-11 Operable Unit contains five RCRA past-practice and five RCRA TSD waste management units. Additionally, for RCRA TSD permitting purposes, the RCRA TSD waste management units are subdivided into two RCRA TSD units

pi-Turns: types, systematics and the context of their occurrence in protein structures.

Science.gov (United States)

Dasgupta, Bhaskar; Chakrabarti, Pinak

2008-09-22

For a proper understanding of protein structure and folding it is important to know if a polypeptide segment adopts a conformation inherent in the sequence or it depends on the context of its flanking secondary structures. Turns of various lengths have been studied and characterized starting from three-residue gamma-turn to six-residue pi-turn. The Schellman motif occurring at the C-terminal end of alpha-helices is a classical example of hydrogen bonded pi-turn involving residues at (i) and (i+5) positions. Hydrogen bonded and non-hydrogen bonded beta- and alpha-turns have been identified previously; likewise, a systematic characterization of pi-turns would provide valuable insight into turn structures. An analysis of protein structures indicates that at least 20% of pi-turns occur independent of the Schellman motif. The two categories of pi-turns, designated as pi-HB and SCH, have been further classified on the basis of backbone conformation and both have AAAa as the major class. They differ in the residue usage at position (i+1), the former having a large preference for Pro that is absent in the latter. As in the case of shorter length beta- and alpha-turns, pi-turns have also been identified not only on the basis of the existence of hydrogen bond, but also using the distance between terminal C alpha-atoms, and this resulted in a comparable number of non-hydrogen-bonded pi-turns (pi-NHB). The presence of shorter beta- and alpha-turns within all categories of pi-turns, the subtle variations in backbone torsion angles along the turn residues, the location of the turns in the context of tertiary structures have been studied. pi-turns have been characterized, first using hydrogen bond and the distance between C alpha atoms of the terminal residues, and then using backbone torsion angles. While the Schellman motif has a structural role in helix termination, many of the pi-HB turns, being located on surface cavities, have functional role and there is also sequence

Topological side-chain classification of beta-turns: ideal motifs for peptidomimetic development.

Science.gov (United States)

Tran, Tran Trung; McKie, Jim; Meutermans, Wim D F; Bourne, Gregory T; Andrews, Peter R; Smythe, Mark L

2005-08-01

Beta-turns are important topological motifs for biological recognition of proteins and peptides. Organic molecules that sample the side chain positions of beta-turns have shown broad binding capacity to multiple different receptors, for example benzodiazepines. Beta-turns have traditionally been classified into various types based on the backbone dihedral angles (phi2, psi2, phi3 and psi3). Indeed, 57-68% of beta-turns are currently classified into 8 different backbone families (Type I, Type II, Type I', Type II', Type VIII, Type VIa1, Type VIa2 and Type VIb and Type IV which represents unclassified beta-turns). Although this classification of beta-turns has been useful, the resulting beta-turn types are not ideal for the design of beta-turn mimetics as they do not reflect topological features of the recognition elements, the side chains. To overcome this, we have extracted beta-turns from a data set of non-homologous and high-resolution protein crystal structures. The side chain positions, as defined by C(alpha)-C(beta) vectors, of these turns have been clustered using the kth nearest neighbor clustering and filtered nearest centroid sorting algorithms. Nine clusters were obtained that cluster 90% of the data, and the average intra-cluster RMSD of the four C(alpha)-C(beta) vectors is 0.36. The nine clusters therefore represent the topology of the side chain scaffold architecture of the vast majority of beta-turns. The mean structures of the nine clusters are useful for the development of beta-turn mimetics and as biological descriptors for focusing combinatorial chemistry towards biologically relevant topological space.

Head turning as a prominent motor symptom in status epilepticus.

Science.gov (United States)

Bauer, Gerhard; Broessner, Gregor; Unterberger, Iris; Walser, Gerald; Pfausler, Bettina; Trinka, Eugen

2008-06-01

Head and eye turning is frequently observed during seizures. Versions with tonic and/or clonic symptoms can be differentiated from smooth head deviations. Head turning as a prominent symptom of status epilepticus has not previously been reported. We present eight case reports, (7 women/1 man, mean age 41 years, median 41.5, range 10 to 74), of status epilepticus (SE), with head turning as a prominent motor symptom. Six were accompanied by continuous frontal, occipital and temporal ictal epileptiform discharges. Furthermore, two patients had absence status with rhythmic and clonic head versions. While the localizing significance of head turnings in SE is low, in our cases, the direction was away from the discharging hemisphere in all cases of focal SE regardless of whether the turning was classified as version (three cases) or deviation (three cases). In this small series of SE, the classical observation of a patient looking away from the discharging hemisphere is still valid.

Turn Management or Impression Management?

NARCIS (Netherlands)

ter Maat, Mark; Heylen, Dirk K.J.; Ruttkay, Z.M.; Kipp, M.; Nijholt, Antinus; Vilhjálmsson, H.H.

2009-01-01

We look at how some basic choices in the management of turns influence the impression that people get from an agent. We look at scales concerning personality, emotion and interpersonal stance. We do this by a person perception study, or rather an agent perception study, using simulated conversations

Professional Employees Turn to Unions

Science.gov (United States)

Chamot, Dennis

1976-01-01

White-collar and professional employees are increasingly turning to unions to combat their loss of independence as employees of large organizations. Managers should realize that they and professional employees have different viewpoints about job situations and that the current trend toward white-collar unionism is apt to continue. (JG)

A Cognitive Analysis of Truck Drivers’ Right-hand Turns

DEFF Research Database (Denmark)

Sieker, Tobias Grønborg; G. Skulason, Thorgeir; Sletting, Kristian

2015-01-01

This paper presents an investigation of truck drivers’ performance during right-hand turns performed in intersections with traffic lights in order to elicit the truck drivers’ domain, decision-making processes, and the strategies used while executing the turn. To gain knowledge about this, a truc...

Did you get any help? A post-hoc secondary analysis of a randomized controlled trial of psychoeducation for patients with antisocial personality disorder in outpatient substance abuse treatment programs.

Science.gov (United States)

Thylstrup, Birgitte; Schrøder, Sidsel; Fridell, Mats; Hesse, Morten

2017-01-09

People in treatment for substance use disorder commonly have comorbid personality disorders, including antisocial personality disorder. Little is known about treatments that specifically address comorbid antisocial personality disorder. Self-rated help received for antisocial personality disorder was assessed during follow-ups at 3, 9 and 15 months post-randomization of a randomized trial of psychoeducation for people with comorbid substance use and antisocial personality disorder (n = 175). Randomization to psychoeducation was associated with increased perceived help for antisocial personality disorder. Perceived help for antisocial personality disorder was in turn associated with more days abstinent and higher treatment satisfaction at the 3-month follow-up, and reduced risk of dropping out of treatment after the 3-month follow-up, and perceived help mediated the effects of random assignment on days abstinent at 3-month. Brief psychoeducation for antisocial personality disorder increased patients' self-rated help for antisocial personality disorder in substance abuse treatment, and reporting having received help for antisocial personality disorder was in turn associated with better short-term outcomes, e.g., days abstinent, dropout from treatment and treatment satisfaction. ISRCTN registry, ISRCTN67266318 , retrospectively registered 17/7/2012.

Assessing lexical, syntactic, and conceptual turn-by-turn alignment in conversations involving conflict and deception

DEFF Research Database (Denmark)

Duran, Nicholas; Fusaroli, Riccardo; Paxton, Alexandra

2015-01-01

-based NLP tools, the procedure begins by taking conversational partners' turns and converting each into a lemmatized sequence of words, assigning part-of-speech tags and computing high-dimensional semantic vectors per each utterance. Words and part-of-speech tags are further sequenced into n-g! rams...

Turn me on! Using the “Internet of Things” to turn things on and off

CSIR Research Space (South Africa)

Butgereit, L

2011-10-01

Full Text Available to the Internet. There are many examples of things posting their status on Twitter and allowing uni-directional access. TurnMeOn is an example of allowing bidirectional access between people and things using Internet protocols. Users can query the status of a...

Semiautomatic machine for turning inside out industrial leather gloves

International Nuclear Information System (INIS)

Aragón-Gonzalez, G; Cano-Blanco, M; León-Galicia, A; Medrano-Sierra, L F; Morales-Gómez, J R

2015-01-01

The last step in the industrial leather gloves manufacturing is to turn the inside out so that the sewing be in the inside of the glove. This work presents the design and testing of a machine for that purpose. In order to quantify the relevant variables, testing was performed with a prototype glove. The employed devices and the testing proceeding were developed experimentally. The obtained information was used to build the turning inside out machine. This machine works with pneumatic power to carry the inside out turning by means of double effect lineal actuators. It has two independent work stations that could be operated simultaneously by two persons, one in each station or in single mode operating one station by one person. The turning inside out cycle is started by means of directional control valves operated with pedals. The velocity and developed force by the actuators is controlled with typical pneumatic resources. The geometrical dimensions of the machine are: 1.15 m length; 0.71 m width and 2.15 m high. Its approximated weight is 120 kg. The air consumption is 5.4 fps by each working station with 60 psig work pressure. The turning inside out operation is 40 s for each industrial leather glove

Identification of a key structural element for protein folding within beta-hairpin turns.

Science.gov (United States)

Kim, Jaewon; Brych, Stephen R; Lee, Jihun; Logan, Timothy M; Blaber, Michael

2003-05-09

Specific residues in a polypeptide may be key contributors to the stability and foldability of the unique native structure. Identification and prediction of such residues is, therefore, an important area of investigation in solving the protein folding problem. Atypical main-chain conformations can help identify strains within a folded protein, and by inference, positions where unique amino acids may have a naturally high frequency of occurrence due to favorable contributions to stability and folding. Non-Gly residues located near the left-handed alpha-helical region (L-alpha) of the Ramachandran plot are a potential indicator of structural strain. Although many investigators have studied mutations at such positions, no consistent energetic or kinetic contributions to stability or folding have been elucidated. Here we report a study of the effects of Gly, Ala and Asn substitutions found within the L-alpha region at a characteristic position in defined beta-hairpin turns within human acidic fibroblast growth factor, and demonstrate consistent effects upon stability and folding kinetics. The thermodynamic and kinetic data are compared to available data for similar mutations in other proteins, with excellent agreement. The results have identified that Gly at the i+3 position within a subset of beta-hairpin turns is a key contributor towards increasing the rate of folding to the native state of the polypeptide while leaving the rate of unfolding largely unchanged.

Neurodharma Self-Help: Personalized Science Communication as Brain Management.

Science.gov (United States)

Eklöf, Jenny

2017-09-01

Over the past ten to fifteen years, medical interventions, therapeutic approaches and scientific studies involving mindfulness meditation have gained traction in areas such as clinical psychology, psychotherapy, and neuroscience. Simultaneously, mindfulness has had a very strong public appeal. This article examines some of the ways in which the medical and scientific meaning of mindfulness is communicated in public and to the public. In particular, it shows how experts in the field of mindfulness neuroscience seek to communicate to the public at large the imperative of brain fitness for the promotion of health, wellbeing and happiness. The study identifies claims being made in popular outlets that, by and large, bypass traditional mass media, such as self-help books, websites and online videos. By treating this material as a form of personalized science communication, this article contributes to the body of literature that understands science communication as a continuum and the boundary between science and popularized science as the outcome of human negotiations. The study finds that processes of personalization help to build bridges between scientific findings and their supposed application, that they infuse science with subjective meaning, and turn expert communication with the public into a moral vocation.

Family matters: Directionality of turning bias while kissing is modulated by context.

Science.gov (United States)

Sedgewick, Jennifer R; Elias, Lorin J

2016-01-28

When leaning forward to kiss to a romantic partner, individuals tend to direct their kiss to the right more often than the left. Studies have consistently demonstrated this kissing asymmetry, although other factors known to influence lateral biases, such as sex or situational context, had yet to be explored. The primary purpose of our study was to investigate if turning direction was consistent between a romantic (parent-parent) and parental (parent-child) kissing context, and secondly, to examine if sex differences influenced turning bias between parent-child kissing partners. An archival analysis coded the direction of turning bias for 161 images of romantic kissing (mothers kissing fathers) and 529 images of parental kissing (mothers or fathers kissing sons or daughters). The results indicated that the direction of turning bias differed between kissing contexts. As expected, a right-turn bias was observed for romantic kissing; however, a left-turn bias was exhibited for parental kissing. There was no significant difference of turning bias between any parent-child kissing partners. Interpretations for the left-turn bias discuss parental kissing as a learned lateral behaviour.

TESTING OF THE OSCILLATIONS DAMPING CAPABILITY BY EXTERNAL TURNING WITH THE USE OF ALTERNATE BARS IN THE CONSTRUCTION OF THE TURNING TOOL HOLDER

Directory of Open Access Journals (Sweden)

Marten Madissoo

2015-09-01

Full Text Available Modern machinery is highly demanding and the requirement for producing high quality parts is crucial in modern engineering. The most important is the setting of dimensions and tolerances of the surfaces which work together. The shape- and position tolerances may raise the existence of failures and can affect the performance of different machinery. Consequently it is very important that the cutting process is as stable as possible in order to get the best quality parts and to achieve the maximum lifetime of the cutting tool. Unfortunately the machining of complex products from hard materials is accompanied by loss of stability of the cutting process, which leads to tool oscillations, causing an increasing wear of the cutting tools, reducing the lifetime of the machine actuators, which ultimately affects the quality and accuracy of processing responsible products. To avoid this kind of chatter vibrations it is possible to construct specialized cutting tools and tool holder witch reduce this kind of vibrations and can help to increase the manufacturing precision of machine components. In consequence of this the paper focuses on testing the utility effect of a cutting tool holder with alternate bars of different material structure in its construction. The different bars are made from rolled steel and have an anisotropic structure which also has different mechanical properties. This construction is considered as a method to improve the cutting stability of the cutting tool and helps to reduce the oscillations in the finishing turning. The method for the construction of the damper instrument holder with alternate bars is proposed.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7351

Cutting forces during turning with variable depth of cut

Directory of Open Access Journals (Sweden)

M. Sadílek

2016-03-01

The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

An expert machine tools selection system for turning operation

NARCIS (Netherlands)

Tan, C.F.; Khalil, S.N.; Karjanto, J.; Wahidin, L.S.; Chen, W.; Rauterberg, G.W.M.

2015-01-01

The turning machining process is an important process in the manufacturing industry. It is important to select the right tool for the turning process so that the manufacturing cost will be decreased. The main objective of this research is to select the most suitable machine tools with respect to

RCRA facility investigation/corrective measures study work plan for the 100-HR-1 operable unit, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1992-09-01

Four areas of the Hanford Site (the 100, 200, 300, and 1100 Areas) have been included on the US. Environmental Protection Agency's (EPA's) National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). Under the Hanford Federal Facility Agreement and Consent Order, signed by the Washington State Department of Ecology (Ecology), EPA, and the US Department of Energy (DOE), more than 1,000 inactive waste disposal and unplanned release sites on the Hanford Site have been grouped into a number of source and groundwater operable units. These operable units contain contamination in the form of hazardous waste, radioactive/hazardous mixed waste, and other CERCLA hazardous substances. This work plan and the attached supporting project plans establish the operable unit setting and the objectives, procedures, tasks, and schedule for conducting the RCRA facility investigation/corrective measures study (RFI/CMS) for the 100-HR-1 source operable unit. Source operable units include facilities and unplanned release sites that are potential sources of contamination. The 100-HR-3 operable unit underlies the D/DR and H Areas, the 600 Area between them, and the six source operable units these areas contain. The 100-HR-3 operable unit includes all contamination found in the aquifer soils and water within its boundary. Separate work plans have been initiated for the 100-HR-3 groundwater operable unit (DOE-RL 1992a) and the 100-DR-1 (DOE-RL 1992b) source operable units

Support vector machines for prediction and analysis of beta and gamma-turns in proteins.

Science.gov (United States)

Pham, Tho Hoan; Satou, Kenji; Ho, Tu Bao

2005-04-01

Tight turns have long been recognized as one of the three important features of proteins, together with alpha-helix and beta-sheet. Tight turns play an important role in globular proteins from both the structural and functional points of view. More than 90% tight turns are beta-turns and most of the rest are gamma-turns. Analysis and prediction of beta-turns and gamma-turns is very useful for design of new molecules such as drugs, pesticides, and antigens. In this paper we investigated two aspects of applying support vector machine (SVM), a promising machine learning method for bioinformatics, to prediction and analysis of beta-turns and gamma-turns. First, we developed two SVM-based methods, called BTSVM and GTSVM, which predict beta-turns and gamma-turns in a protein from its sequence. When compared with other methods, BTSVM has a superior performance and GTSVM is competitive. Second, we used SVMs with a linear kernel to estimate the support of amino acids for the formation of beta-turns and gamma-turns depending on their position in a protein. Our analysis results are more comprehensive and easier to use than the previous results in designing turns in proteins.

Why Does Hair Turn Gray?

Science.gov (United States)

... out, but people with naturally lighter hair are just as likely to go gray. From the time a person notices a few gray hairs, it may take more than 10 years for all of that person's hair to turn ... really believe that this happens. Just in case, try not to freak out your ...

Crack turning in integrally stiffened aircraft structures

Science.gov (United States)

Pettit, Richard Glen

Current emphasis in the aircraft industry toward reducing manufacturing cost has created a renewed interest in integrally stiffened structures. Crack turning has been identified as an approach to improve the damage tolerance and fail-safety of this class of structures. A desired behavior is for skin cracks to turn before reaching a stiffener, instead of growing straight through. A crack in a pressurized fuselage encounters high T-stress as it nears the stiffener---a condition favorable to crack turning. Also, the tear resistance of aluminum alloys typically varies with crack orientation, a form of anisotropy that can influence the crack path. The present work addresses these issues with a study of crack turning in two-dimensions, including the effects of both T-stress and fracture anisotropy. Both effects are shown to have relation to the process zone size, an interaction that is central to this study. Following an introduction to the problem, the T-stress effect is studied for a slightly curved semi-infinite crack with a cohesive process zone, yielding a closed form expression for the future crack path in an infinite medium. For a given initial crack tip curvature and tensile T-stress, the crack path instability is found to increase with process zone size. Fracture orthotropy is treated using a simple function to interpolate between the two principal fracture resistance values in two-dimensions. An extension to three-dimensions interpolates between the six principal values of fracture resistance. Also discussed is the transition between mode I and mode II fracture in metals. For isotropic materials, there is evidence that the crack seeks out a direction of either local symmetry (pure mode I) or local asymmetry (pure mode II) growth. For orthotropic materials the favored states are not pure modal, and have mode mixity that is a function of crack orientation. Drawing upon these principles, two crack turning prediction approaches are extended to include fracture

Prediction of beta-turns and beta-turn types by a novel bidirectional Elman-type recurrent neural network with multiple output layers (MOLEBRNN).

Science.gov (United States)

Kirschner, Andreas; Frishman, Dmitrij

2008-10-01

Prediction of beta-turns from amino acid sequences has long been recognized as an important problem in structural bioinformatics due to their frequent occurrence as well as their structural and functional significance. Because various structural features of proteins are intercorrelated, secondary structure information has been often employed as an additional input for machine learning algorithms while predicting beta-turns. Here we present a novel bidirectional Elman-type recurrent neural network with multiple output layers (MOLEBRNN) capable of predicting multiple mutually dependent structural motifs and demonstrate its efficiency in recognizing three aspects of protein structure: beta-turns, beta-turn types, and secondary structure. The advantage of our method compared to other predictors is that it does not require any external input except for sequence profiles because interdependencies between different structural features are taken into account implicitly during the learning process. In a sevenfold cross-validation experiment on a standard test dataset our method exhibits the total prediction accuracy of 77.9% and the Mathew's Correlation Coefficient of 0.45, the highest performance reported so far. It also outperforms other known methods in delineating individual turn types. We demonstrate how simultaneous prediction of multiple targets influences prediction performance on single targets. The MOLEBRNN presented here is a generic method applicable in a variety of research fields where multiple mutually depending target classes need to be predicted. http://webclu.bio.wzw.tum.de/predator-web/.

Expanding the peptide beta-turn in alphagamma hybrid sequences: 12 atom hydrogen bonded helical and hairpin turns.

Science.gov (United States)

Chatterjee, Sunanda; Vasudev, Prema G; Raghothama, Srinivasarao; Ramakrishnan, Chandrasekharan; Shamala, Narayanaswamy; Balaram, Padmanabhan

2009-04-29

Hybrid peptide segments containing contiguous alpha and gamma amino acid residues can form C(12) hydrogen bonded turns which may be considered as backbone expanded analogues of C(10) (beta-turns) found in alphaalpha segments. Exploration of the regular hydrogen bonded conformations accessible for hybrid alphagamma sequences is facilitated by the use of a stereochemically constrained gamma amino acid residue gabapentin (1-aminomethylcyclohexaneacetic acid, Gpn), in which the two torsion angles about C(gamma)-C(beta) (theta(1)) and C(beta)-C(alpha) (theta(2)) are predominantly restricted to gauche conformations. The crystal structures of the octapeptides Boc-Gpn-Aib-Gpn-Aib-Gpn-Aib-Gpn-Aib-OMe (1) and Boc-Leu-Phe-Val-Aib-Gpn-Leu-Phe-Val-OMe (2) reveal two distinct conformations for the Aib-Gpn segment. Peptide 1 forms a continuous helix over the Aib(2)-Aib(6) segment, while the peptide 2 forms a beta-hairpin structure stabilized by four cross-strand hydrogen bonds with the Aib-Gpn segment forming a nonhelical C(12) turn. The robustness of the helix in peptide 1 in solution is demonstrated by NMR methods. Peptide 2 is conformationally fragile in solution with evidence of beta-hairpin conformations being obtained in methanol. Theoretical calculations permit delineation of the various C(12) hydrogen bonded structures which are energetically feasible in alphagamma and gammaalpha sequences.

BetaTPred: prediction of beta-TURNS in a protein using statistical algorithms.

Science.gov (United States)

Kaur, Harpreet; Raghava, G P S

2002-03-01

beta-turns play an important role from a structural and functional point of view. beta-turns are the most common type of non-repetitive structures in proteins and comprise on average, 25% of the residues. In the past numerous methods have been developed to predict beta-turns in a protein. Most of these prediction methods are based on statistical approaches. In order to utilize the full potential of these methods, there is a need to develop a web server. This paper describes a web server called BetaTPred, developed for predicting beta-TURNS in a protein from its amino acid sequence. BetaTPred allows the user to predict turns in a protein using existing statistical algorithms. It also allows to predict different types of beta-TURNS e.g. type I, I', II, II', VI, VIII and non-specific. This server assists the users in predicting the consensus beta-TURNS in a protein. The server is accessible from http://imtech.res.in/raghava/betatpred/

Remedial investigation work plan for Bear Creek Valley Operable Unit 2 (Rust Spoil Area, SY-200 Yard, Spoil Area 1) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Environmental Restoration Program

Energy Technology Data Exchange (ETDEWEB)

1993-05-01

The enactment of the Resource Conservation and Recovery Act (RCRA) in 1976 and the Hazardous and Solid Waste Amendments (HSWA) to RCRA in 1984 created management requirements for hazardous waste facilities. The facilities within the Oak Ridge Reservation (ORR) were in the process of meeting the RCRA requirements when ORR was placed on the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) National Priorities List (NPL) on November 21, 1989. Under RCRA, the actions typically follow the RCRA Facility Assessment (RFA)/RCRA Facility Investigation (RFI)/Corrective Measures Study (CMS)/Corrective Measures implementation process. Under CERCLA the actions follow the PA/SI/Remedial Investigation (RI)/Feasibility Study (FS)/Remedial Design/Remedial Action process. The development of this document will incorporate requirements under both RCRA and CERCLA into an RI work plan for the characterization of Bear Creek Valley (BCV) Operable Unit (OU) 2.

Remedial investigation work plan for Bear Creek Valley Operable Unit 2 (Rust Spoil Area, SY-200 Yard, Spoil Area 1) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-05-01

The enactment of the Resource Conservation and Recovery Act (RCRA) in 1976 and the Hazardous and Solid Waste Amendments (HSWA) to RCRA in 1984 created management requirements for hazardous waste facilities. The facilities within the Oak Ridge Reservation (ORR) were in the process of meeting the RCRA requirements when ORR was placed on the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) National Priorities List (NPL) on November 21, 1989. Under RCRA, the actions typically follow the RCRA Facility Assessment (RFA)/RCRA Facility Investigation (RFI)/Corrective Measures Study (CMS)/Corrective Measures implementation process. Under CERCLA the actions follow the PA/SI/Remedial Investigation (RI)/Feasibility Study (FS)/Remedial Design/Remedial Action process. The development of this document will incorporate requirements under both RCRA and CERCLA into an RI work plan for the characterization of Bear Creek Valley (BCV) Operable Unit (OU) 2

Remedial investigation report on Bear Creek Valley Operable Unit 2 (Rust Spoil Area, Spoil Area 1, and SY-200 Yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 1, Main text

International Nuclear Information System (INIS)

1994-08-01

The enactment of the Resource Conservation and Recovery Act (RCRA) in 1976 and the Hazardous and Solid Waste Amendments (HSWA) to RCRA in 1984 created management requirements for hazardous waste facilities. The facilities within the Oak Ridge Reservation (ORR) were in the process of meeting the RCRA requirements when the ORR was placed on the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) National Priorities List (NPL) on November 21, 1989. Under RCRA, the actions typically follow the RCRA Facility Assessment/RCRA Facility Investigation (RFI)/Corrective Measures Study (CMS)/Corrective Measures Implementation process. Under CERCLA, the actions follow the preliminary assessment/site investigation/Remedial Investigation (RI)/Feasibility Study (FS)/Remedial Design/Remedial Action process. This document incorporates requirements under both RCRA and CERCLA in the form of an RI report for the characterization of Bear Creek Valley (BCV) Operable Unit (OU) 2

Effect of stern hull shape on turning circle of ships

Science.gov (United States)

Jaswar, Maimun, A.; Wahid, M. A.; Priyanto, A.; Zamani, Pauzi, Saman

2012-06-01

Many factors such as: stern hull shape, length, draught, trim, propulsion system and external forces affecting the drift angle influence rate of turn and size of turning circle of ships. This paper discusses turning circle characteristics of U and V stern hull shape of Very Large Crude Oil Carrier (VLCC) ships. The ships have same principal dimension such as length, beam, and draught. The turning circle characteristics of the VLCC ships are simulated at 35 degree of rudder angle. In the analysis, firstly, turning circle performance of U-type VLCC ship is simulated. In the simulation, initial ship speed is determined using given power and rpm. Hydrodynamic derivatives coefficients are determined by including effect of fullness of aft run. Using the obtained, speed and hydrodynamic coefficients, force and moment acting on hull, force and moment induced by propeller, force and moment induced by rudder are determined. Finally, ship trajectory, ratio of speed, yaw angle and drift angle are determined. Results of simulation results of the VLCC ship are compared with the experimental one as validation. Using the same method, V-type VLCC is simulated and the simulation results are compared with U-type VLCC ship. Results shows the turning circle of U-type is larger than V-type due to effect stern hul results of simulation are.

Measurement of signal use and vehicle turns as indication of driver cognition.

Science.gov (United States)

Wallace, Bruce; Goubran, Rafik; Knoefel, Frank

2014-01-01

This paper uses data analytics to provide a method for the measurement of a key driving task, turn signal usage as a measure of an automatic over-learned cognitive function drivers. The paper augments previously reported more complex executive function cognition measures by proposing an algorithm that analyzes dashboard video to detect turn indicator use with 100% accuracy without any false positives. The paper proposes two algorithms that determine the actual turns made on a trip. The first through analysis of GPS location traces for the vehicle, locating 73% of the turns made with a very low false positive rate of 3%. A second algorithm uses GIS tools to retroactively create turn by turn directions. Fusion of GIS and GPS information raises performance to 77%. The paper presents the algorithm required to measure signal use for actual turns by realigning the 0.2Hz GPS data, 30fps video and GIS turn events. The result is a measure that can be tracked over time and changes in the driver's performance can result in alerts to the driver, caregivers or clinicians as indication of cognitive change. A lack of decline can also be shared as reassurance.

Analysis of the lateral push-off in the freestyle flip turn.

Science.gov (United States)

Araujo, Luciana; Pereira, Suzana; Gatti, Roberta; Freitas, Elinai; Jacomel, Gabriel; Roesler, Helio; Villas-Boas, Joao

2010-09-01

The aim of this study was to examine the contact phase during the lateral push-off in the turn of front crawl swimming to determine which biomechanical variables (maximum normalized peak force, contact time, impulse, angle of knee flexion, and total turn time within 15 m) contribute to the performance of this turn technique. Thirty-four swimmers of state, national, and international competitive standard participated in the study. For data collection, the following equipment was used: an underwater force platform, a 30-Hz VHS video camera, and a MiniDv digital camera within an underwater box. Data are expressed as descriptive statistics. Inferential analyses were performed using Pearson's correlation and multiple linear regressions. All variables studied had a significant relationship with turn performance. We conclude that a turn executed with a knee flexion angle of between 100° and 120° provides optimum peak forces to generate impulses that allow the swimmer to lose less time in the turn without the need for an excessive force application and with less energy lost.

A novel method for calculating the energy cost of turning during running

Directory of Open Access Journals (Sweden)

Hatamoto Y

2013-05-01

Full Text Available Yoichi Hatamoto,1 Yosuke Yamada,2 Tatsuya Fujii,3 Yasuki Higaki,3 Akira Kiyonaga,3 Hiroaki Tanaka31Graduate School of Sports and Health Science, Fukuoka University, Nanakuma Jonan-ku Fukuoka, Japan; 2The Fukuoka University Institute for Physical Activity, Nanakuma Jonan-ku Fukuoka, Japan; 3Faculty of Sports and Health Science, Fukuoka University, Nanakuma Jonan-ku Fukuoka, JapanAbstract: Although changes of direction are one of the essential locomotor patterns in ball sports, the physiological demand of turning during running has not been previously investigated. We proposed a novel approach by which to evaluate the physiological demand of turning. The purposes of this study were to establish a method of measuring the energy expenditure (EE of a 180° turn during running and to investigate the effect of two different running speeds on the EE of a 180° turn. Eleven young, male participants performed measurement sessions at two different running speeds (4.3 and 5.4 km/hour. Each measurement session consisted of five trials, and each trial had a different frequency of turns. At both running speeds, as the turn frequency increased the gross oxygen consumption (V · O2 also increased linearly (4.3 km/hour, r = 0.973; 5.4 km/hour, r = 0.996. The V · O2 of a turn at 5.4 km/hour (0.55 [SD 0.09] mL/kg was higher than at 4.3 km/hour (0.34 [SD 0.13] mL/kg (P < 0.001. We conclude that the gross V · O2 of running at a fixed speed with turns is proportional to turn frequency and that the EE of a turn is different at different running speeds. The Different Frequency Accumulation Method is a useful tool for assessing the physiological demands of complex locomotor activity.Keywords: energy expenditure, turning, turn frequency, running speed, V · O2, heart rate

Now, It's Your Turn: How You Can Take Medicine Safely

Science.gov (United States)

... turn Javascript on. Feature: Taking Medicines Safely Now, It's Your Turn: How You Can Take Medicine Safely ... medicine. The pharmacist has filled the prescription. Now it's up to you to take the medicine safely. ...

Helping You Help Me: The Role of Diagnostic (In)congruence in the Helping Process within Organizations

OpenAIRE

Fisher, Colin M.; Pillemer, Julianna; Amabile, Teresa M.

2014-01-01

Through an inductive, multi-method field study at a major design firm, we investigated the helping process in project work and how that process affects the success of a helping episode, as perceived by help-givers and/or -receivers. We used daily diary entries and weekly interviews from four project teams, and a separate sample of critical incident interviews, to induce process models of successful and unsuccessful helping episodes. We found that, in unsuccessful episodes, help-givers and -re...

ANALYSIS OF CHIP FORMATION DURING HARD TURNING THROUGH ACOUSTIC EMISSION

Directory of Open Access Journals (Sweden)

Miroslav Neslušan

2012-01-01

Full Text Available The paper deals with analysis of chip formation and related aspects of the chip formation during turning hardened steel 100Cr6. The paper draws a comparison of some aspects of the chip formation between turning annealed and hardened roll bearing steel. The results of the analysis show that there is the formation of a segmented chip in the case of hard turning. Frequency of segmentation is very high. A conventional piezoelectric dynamometer limits the frequency response to about 3.5 kHz. On the other hand, the frequency of process fluctuation may by obtained by using accelerometers or acoustic emission. This paper reports about the dynamic character of cutting process when hard turning and correlation among the calculated segmentation frequencies and the experimental analysis.

Helping HELP with limited resources: the Luquillo experience

Science.gov (United States)

F.N. Scatena; JR Ortiz-Zayas; J.F. Blanco-Libreros

2008-01-01

By definition the HELP approach involves the active participation of individuals from a wide range of disciplines and backgrounds, including representatives of industry, academics, natural resource managers, and local officials and community leaders. While there is considerable enthusiasm and support for the integrated HELP approach, a central problem for all HELP...

Diamond turning of glass

Energy Technology Data Exchange (ETDEWEB)

Blackley, W.S.; Scattergood, R.O.

1988-12-01

A new research initiative will be undertaken to investigate the critical cutting depth concepts for single point diamond turning of brittle, amorphous materials. Inorganic glasses and a brittle, thermoset polymer (organic glass) are the principal candidate materials. Interrupted cutting tests similar to those done in earlier research are Ge and Si crystals will be made to obtain critical depth values as a function of machining parameters. The results will provide systematic data with which to assess machining performance on glasses and amorphous materials

Optical spectroscopic elucidation of beta-turns in disulfide bridged cyclic tetrapeptides.

Science.gov (United States)

Borics, Attila; Murphy, Richard F; Lovas, Sándor

2007-01-01

Vibrational circular dichroism (VCD) spectroscopic features of type II beta-turns were characterized previously, but, criteria for differentiation between beta-turn types had not been established yet. Model tetrapeptides, cyclized through a disulfide bridge, were designed on the basis of previous experimental results and the observed incidence of amino acid residues in the i + 1 and i + 2 positions in beta-turns, to determine the features of VCD spectra of type I and II beta-turns. The results were correlated with electronic circular dichroism (ECD) spectra and VCD spectra calculated from conformational data obtained by molecular dynamics (MD) simulations. All cyclic tetrapeptides yielded VCD signals with a higher frequency negative and a lower frequency positive couplet with negative lobes overlapping. MD simulations confirmed the conformational homogeneity of these peptides in solution. Comparison with ECD spectroscopy, MD, and quantum chemical calculation results suggested that the low frequency component of VCD spectra originating from the tertiary amide vibrations could be used to distinguish between types of beta-turn structures. On the basis of this observation, VCD spectroscopic features of type II and VIII beta-turns and ECD spectroscopic properties of a type VIII beta-turn were suggested. The need for independent experimental as well as theoretical investigations to obtain decisive conformational information was recognized. Copyright 2006 Wiley Periodicals, Inc.

Getting Help

Science.gov (United States)

... Parents & Students Home > Special Features > Getting Help Getting Help Resources from NIAAA Treatment for Alcohol Problems: Finding ... and find ways to make a change. Professional help Your doctor. Primary care and mental health practitioners ...

Turning university professors into competent learners

NARCIS (Netherlands)

Stefanova, Eliza; Ilieva, Miroslava; Nikolova, Nikolina; Stefanov, Krassen

2008-01-01

Stefanova, E., Ilieva, M., Nikolova, N, & Stefanov, K. (2008). Turning university professors into competent learners. In H. W. Sligte & R. Koper (Eds.), Proceedings of the 4th TENCompetence Open Workshop. Empowering Learners for Lifelong Competence Development: pedagogical, organisational and

Cellular Reprogramming–Turning the Clock Back

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 18; Issue 6. Cellular Reprogramming - Turning the Clock Back - Nobel Prize in Physiology or Medicine, 2012. Deepa Subramanyam. General Article Volume 18 Issue 6 June 2013 pp 514-521 ...

Ignition experiment in a single-turn-coil tokamak

International Nuclear Information System (INIS)

Carrera, R.; Driga, M.; Gully, J.H.

1989-01-01

A novel concept for a fusion ignition experiment, IGNITEX proposed along the lines of previous ideas for a compact thermonuclear device is analyzed. A single-turn-coil tokamak is analyzed. A single-turn-coil tokamak supplied by homopolar generators can ohmically heat a DT plasma to ignition conditions and maintain a thermally stable ignited phase for about ten energy confinement times. The IGNITEX experiment can provide a simple and relatively inexpensive way to produce and control ignited plasmas for scientific study

Models and Algorithms for Tracking Target with Coordinated Turn Motion

Directory of Open Access Journals (Sweden)

Xianghui Yuan

2014-01-01

Full Text Available Tracking target with coordinated turn (CT motion is highly dependent on the models and algorithms. First, the widely used models are compared in this paper—coordinated turn (CT model with known turn rate, augmented coordinated turn (ACT model with Cartesian velocity, ACT model with polar velocity, CT model using a kinematic constraint, and maneuver centered circular motion model. Then, in the single model tracking framework, the tracking algorithms for the last four models are compared and the suggestions on the choice of models for different practical target tracking problems are given. Finally, in the multiple models (MM framework, the algorithm based on expectation maximization (EM algorithm is derived, including both the batch form and the recursive form. Compared with the widely used interacting multiple model (IMM algorithm, the EM algorithm shows its effectiveness.

Effect of a printed reminder in the waiting room to turn off mobile phones during consultation: a before and after study

Directory of Open Access Journals (Sweden)

de Aguiar Sylvia

2009-03-01

Full Text Available Abstract Background Telephone interruptions during consultations are one cause of work-related stress amongst general practitioners. Many health care centers recommend that patients turn off any mobile phones to avoid interruptions to the discussion with the physicians. Methods The purpose of this before and after study was to determine whether a printed reminder for turning off the mobile phone in the waiting room is helpful in decreasing the number of interruptions during consultation. A visual phone off sign utilizing the International "No" symbol of a diagonal line through a circle, along with a "please turn off your phone during consultation" reminder was used in the waiting room in the "after" period. Results A significant difference was found in the proportion of patients receiving or making a call during the consultation (8.8% vs. 13.5%, RR = 0.66; 95%CI 0.46–0.94; p = 0.021 and in the total number of calls (10.4% vs. 17.3%, RR = 0.60; 95%CI 0.44–0.83, p = 0.003 between the exposed and the non-exposed groups. However, no significant differences were found in the total time or the median time spent talking during consultation. The duration of the calls had median times of 20.5 seconds and 22.3 seconds in the exposed and the non-exposed groups respectively. Women from both groups who received a call during consultation answered significantly more when compared to men (70% vs. 52%; p = 0.05; Conclusion Our findings suggest that a printed reminder in the waiting room is helpful in decreasing the number of interruptions by mobile phone during consultation in our settings. The study provides the basis for further quantitative and qualitative research on this topic

Turn-taking in Human Communication--Origins and Implications for Language Processing.

Science.gov (United States)

Levinson, Stephen C

2016-01-01

Most language usage is interactive, involving rapid turn-taking. The turn-taking system has a number of striking properties: turns are short and responses are remarkably rapid, but turns are of varying length and often of very complex construction such that the underlying cognitive processing is highly compressed. Although neglected in cognitive science, the system has deep implications for language processing and acquisition that are only now becoming clear. Appearing earlier in ontogeny than linguistic competence, it is also found across all the major primate clades. This suggests a possible phylogenetic continuity, which may provide key insights into language evolution. Copyright © 2015 Elsevier Ltd. All rights reserved.

MATHEMATICAL MODEL AND METHODOLOGY FOR CALCULATION OF MINIMIZATION ON TURNING RADIUS OF TRACTOR UNIT WITH REPLACEABLE SUPPORTING AND MANEUVERING DEVICE

Directory of Open Access Journals (Sweden)

P. V. Zeleniy

2016-01-01

Full Text Available Smooth plowing with the help of reversible plows has replaced an enclosure method of soil treatment. The method may cause a formation of back ridges or open furrows. Due to this fact turnings of a tractor unit with a minimum radius required in order to ensure shuttle movements each time in the furrow of the preceding operating stroke have become a dominant type of turnings. Non-productive shift time is directly dependent on them and it is on the average 10–12 %, and it is up to 40 % in small contour areas with short run. Large non-productive time is connected with the desire to reduce headland width at field edges, and then a turning is made in several stages while using a complicated maneuvering. Therefore, an increase in efficiency of a plowing unit by means of minimization on its turning radius and execution of turning at one stage in the shortest possible time are considered as relevant objectives. In such a case it is necessary to take into account the fact that potential capabilities of universal tractors having established time-proved designs in respect of reduction of turning radius are practically at the end. So it is expedient to solve the matter at the expense of additional removable devices that ensure transformation of tractor wheel formula at the run end in order to reorient its position. Finally high quality plowing ensured by future-oriented reversible plows will be accompanied not only by output increase per shift, but also by decrease in headland width, their compaction and abrasion due to suspension systems and increase in productivity. The developed design having a novelty which proved by an invention patent and representing an additional supporting and maneuvering device significantly minimizes all the above-mentioned disadvantages and does not require any changes in tractor production design. Investigations have been carried on the following topic: “Minimization of turning radius for universal tractors by transformation

Virtual reality training improves turning capacity and functional reach in stroke patients

International Nuclear Information System (INIS)

Malik, A.N.; Masood, T.

2017-01-01

Objective: To determine the added effects of virtual reality training on turning capacity, gait parameters and functional reach capacity of stroke patients compared to task oriented training alone. Methodology: A randomized control trial was conducted from February 2016 to July 2106 at Physical Rehabilitation Department Pakistan Railway Hospital, Rawalpindi, Pakistan. Twenty stroke patients were selected through purposive sampling. The patients were randomly assigned through sealed envelope method into two groups; Task Oriented Training (TOT) and Virtual Reality Training (VRT) Group. The standardized tools were used for assessment. The TOT was provided for 4 days per week for 6 weeks while VRT group received additional exer-gaming training during sessions. Results: Significant improvement was observed in both groups regarding reaching forward, turning 360, gait pivot turn (p a 0.01) and FRT (p a 0.001). The two groups were statistically different from each other in terms of turning capacity, reaching forward, gait pivot turn and functional reach after 6 weeks of intervention (p a 0.05) Conclusion: Addition of virtual reality training further improves the significant improvement caused by task oriented training on turning capacity, reaching forward, gait pivot turn and functional reach in stroke patients. (author)

Incorporating beta-turns and a turn mimetic out of context in loop 1 of the WW domain affords cooperatively folded beta-sheets.

Science.gov (United States)

Kaul, R; Angeles, A R; Jäger, M; Powers, E T; Kelly, J W

2001-06-06

To probe the conformational requirements of loop 1 in the Pin1 WW domain, the residues at the i + 2 and i + 3 positions of a beta-turn within this loop were replaced by dPro-Gly and Asn-Gly, which are known to prefer the conformations required at the i + 1 and i + 2 positions of type II' and type I' beta-turns. Conformational specificity or lack thereof was further examined by incorporating into the i + 2 and i + 3 positions a non-alpha-amino acid-based beta-turn mimetic (4-(2'-aminoethyl)-6-dibenzofuran propionic acid residue, 1), which was designed to replace the i + 1 and i + 2 positions of beta-turns. All these Pin WW variants are monomeric and folded as discerned by analytical ultracentrifugation, NMR, and CD. They exhibit cooperative two-state transitions and display thermodynamic stability within 0.5 kcal/mol of the wild-type WW domain, demonstrating that the acquisition of native structure and stability does not require a specific sequence and, by extension, conformation within loop 1. However, it could be that these loop 1 mutations alter the kinetics of antiparallel beta-sheet folding, which will be addressed by subsequent kinetic studies.

Remedial investigation work plan for Bear Creek Valley Operable Unit 4 (shallow groundwater in Bear Creek Valley) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1992-12-01

The enactment of the Resource Conservation and Recovery Act (RCRA) in 1976 and the Hazardous and Solid Waste Amendments (HSWA) to RCRA in 1984 created management requirements for hazardous waste fadities. The facilities within the Oak Ridge Reservation (ORR) were in the process of meeting the RCRA requirements when ORR was placed on the Comprehensive Environmental Response, Compensation, and Liability Act (CERCIA) National Priorities List (NPL) on November 21, 1989. Under RCRA, the actions typically follow the RCRA Facility Assessment (RIFA)/RCRA Facility Investigation (RFI)/Coffective Measures Study (CMS)/Corrective Measures Implementation process. Under CERCLA, the actions follow the Pre at sign ary Assessment/Site Investigation (PA/Sl) Remedial Investigation Feasibility Study (RI/FS)/Remedial Design/Remedial Action process. The development of this document will incorporate requirements under both RCRA and CERCIA into an RI Work Plan for the lint phase of characterization of Bear Creek Valley (BCV) Operable Unit (OU) 4

A method for simultaneous linear optics and coupling correction for storage rings with turn-by-turn beam position monitor data

Energy Technology Data Exchange (ETDEWEB)

Yang, Xi [Brookhaven National Laboratory, Upton, Long Island, NY 11973 (United States); Huang, Xiaobiao, E-mail: xiahuang@slac.stanford.edu [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, CA 94025 (United States)

2016-08-21

We propose a method to simultaneously correct linear optics errors and linear coupling for storage rings using turn-by-turn (TbT) beam position monitor (BPM) data. The independent component analysis (ICA) method is used to isolate the betatron normal modes from the measured TbT BPM data. The betatron amplitudes and phase advances of the projections of the normal modes on the horizontal and vertical planes are then extracted, which, combined with dispersion measurement, are used to fit the lattice model. The fitting results are used for lattice correction. The method has been successfully demonstrated on the NSLS-II storage ring.

A method for simultaneous linear optics and coupling correction for storage rings with turn-by-turn beam position monitor data

Energy Technology Data Exchange (ETDEWEB)

Yang, Xi [Brookhaven National Lab. (BNL), Upton, NY (United States); Huang, Xiaobiao [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2016-08-01

We propose a method to simultaneously correct linear optics errors and linear coupling for storage rings using turn-by-turn (TbT) beam position monitor (BPM) data. The independent component analysis (ICA) method is used to isolate the betatron normal modes from the measured TbT BPM data. The betatron amplitudes and phase advances of the projections of the normal modes on the horizontal and vertical planes are then extracted, which, combined with dispersion measurement, are used to fit the lattice model. Furthermore, the fitting results are used for lattice correction. Our method has been successfully demonstrated on the NSLS-II storage ring.

[Abnormal head turn in a patient with Brown's syndrome].

Science.gov (United States)

van Waveren, M; Krzizok, T; Besch, D

2008-08-01

We report on an eight-year-old boy, who was presented in our clinic because of head turn. The cause of the tortecollis (ocular or general) in this case was and still cannot be explained. Only by applying extensive prism adaptation tests it was possible to prove the ocular character of the head turn. An eight-year-old boy with Brown's syndrome was referred to us because of a head tilt to the left side. Six months previously surgery on the M. obl. superior of the right eye was performed in another clinic. No improvement of the head tilt could be observed after the operation. In addition, an exotropia became decompensated. Under a 3-day occlusion of one eye, no change of the head turn and the squint could be measured. No other cause of the head turn could be found by an orthopaedist and a paediatrist. Under a prism of 20 cm/m basis in and 10 cm/m basis against the positive vertical deviation, the head tilt decreased, so that we decided to do a second surgery. The head tilting had not resumed at one year after the surgery. Although the initial diagnostic findings ruled out an ocular cause, it was possible to lessen the head tilting with the aid of the prism adaptation test. This case study emphasises the usefulness of a prism adaptation test of several days duration in order to validate an ocular cause of head turn and to determine an adequate indication for surgery.

How turn-taking strategies influence users’ impressions of an agent

NARCIS (Netherlands)

ter Maat, Mark; Truong, Khiet Phuong; Heylen, Dirk K.J.; Allbeck, Jan; Badler, Norman; Bickmore, Timothy; Pelachaud, Catherine; Safonova, Alla

Different turn-taking strategies of an agent influence the impression that people have of it. We recorded conversations of a human with an interviewing agent, controlled by a wizard and using a particular turn-taking strategy. A questionnaire with 27 semantic differential scales concerning

Observation of diamond turned OFHC copper using Scanning Tunneling Microscopy

Energy Technology Data Exchange (ETDEWEB)

Grigg, D.A.; Russell, P.E.; Dow, T.A.

1988-12-01

Diamond turned OFHC copper samples have been observed within the past few months using the Scanning Tunneling Microscope. Initial results have shown evidence of artifacts which may be used to better understand the diamond turning process. The STM`s high resolution capability and three dimensional data representation allows observation and study of surface features unobtainable with conventional profilometry systems. Also, the STM offers a better quantitative means by which to analyze surface structures than the SEM. This paper discusses findings on several diamond turned OFHC copper samples having different cutting conditions. Each sample has been cross referenced using STM and SEM.

Going Online: Helping Technical Communicators Help Translators.

Science.gov (United States)

Flint, Patricia; Lord van Slyke, Melanie; Starke-Meyerring, Doreen; Thompson, Aimee

1999-01-01

Explains why technical communicators should help translators. Offers tips for creating "translation-friendly" documentation. Describes the research and design process used by the authors to create an online tutorial that provides technical communicators at a medical technology company the information they need to help them write and…

Evaluation of cutting force uncertainty components in turning

DEFF Research Database (Denmark)

Axinte, Dragos Aurelian; Belluco, Walter; De Chiffre, Leonardo

2000-01-01

A procedure is proposed for the evaluation of those uncertainty components of a single cutting force measurement in turning that are related to the contributions of the dynamometer calibration and the cutting process itself. Based on an empirical model including errors form both sources......, the uncertainty for a single measurement of cutting force is presented, and expressions for the expected uncertainty vs. cutting parameters are proposed. This approach gives the possibility of evaluating cutting force uncertainty components in turning, for a defined range of cutting parameters, based on few...

Causal Role of Motor Simulation in Turn-Taking Behavior.

Science.gov (United States)

Hadley, Lauren V; Novembre, Giacomo; Keller, Peter E; Pickering, Martin J

2015-12-16

Overlap between sensory and motor representations has been documented for a range of human actions, from grasping (Rizzolatti et al., 1996b) to playing a musical instrument (Novembre and Keller, 2014). Such overlap suggests that individuals use motor simulation to predict the outcome of observed actions (Wolpert, 1997). Here we investigate motor simulation as a basis of human communication. Using a musical turn-taking task, we show that pianists call on motor representations of their partner's part to predict when to come in for their own turn. Pianists played alternating solos with a videoed partner, and double-pulse transcranial magnetic stimulation was applied around the turn-switch to temporarily disrupt processing in two cortical regions implicated previously in different forms of motor simulation: (1) the dorsal premotor cortex (dPMC), associated with automatic motor resonance during passive observation of hand actions, especially when the actions are familiar (Lahav et al., 2007); and (2) the supplementary motor area (SMA), involved in active motor imagery, especially when the actions are familiar (Baumann et al., 2007). Stimulation of the right dPMC decreased the temporal accuracy of pianists' (right-hand) entries relative to sham when the partner's (left-hand) part had been rehearsed previously. This effect did not occur for dPMC stimulation without rehearsal or for SMA stimulation. These findings support the role of the dPMC in predicting the time course of observed actions via resonance-based motor simulation during turn-taking. Because turn-taking spans multiple modes of human interaction, we suggest that simulation is a foundational mechanism underlying the temporal dynamics of joint action. Even during passive observation, seeing or hearing somebody execute an action from within our repertoire activates motor cortices of our brain. But what is the functional relevance of such "motor simulation"? By combining a musical duet task with a real

Factors influencing turning and its relationship with falls in individuals with Parkinson's disease.

Directory of Open Access Journals (Sweden)

Fang-Yu Cheng

Full Text Available BACKGROUND: Falls are a major problem for people with Parkinson's disease (PD. Many studies indicate that more than 50% of people with PD have difficulty in turning that may lead to falls during daily activities. The aims of this study were to identify the relationship between turning performance and falls, and to determine the factors that influence turning performance. METHODS: This study examined 45 patients with idiopathic PD (Hoehn and Yahr stage 1-3 using a battery of tests, including 180° turn time, balance, and muscle strength. The levels of disease severity and freezing of gait were also measured. The number of falls in the past 6 months was recorded. RESULTS: Sixteen out of forty-five participants experienced falls in the past 6 months. A receiver operating characteristic curve showed that turn time was highly related to falls [more affected side: sensitivity = 0.81, specificity = 0.79, area under the curve (AUC = 0.83; less affected side: sensitivity = 0.88, specificity = 0.76, AUC = 0.83]. The most important factor influencing turn time was balance ability (both sides: p = 0.000 according to the regression model. Correlations between turn time and dynamic balance were further established with reaction time, movement velocity, endpoint excursion, and maximal excursion of the LOS (limits of stability test. CONCLUSION: The time needed to complete a 180° turn during the SQT (step/quick turn test is a good index to differentiate fallers from non-fallers in persons with PD. Turn time is most influenced by balance. Furthermore, balance control, especially in an anterior or sideways direction, is important for turning performance.

A model of sexually and physically victimized women's process of attaining effective formal help over time: the role of social location, context, and intervention.

Science.gov (United States)

Kennedy, Angie C; Adams, Adrienne; Bybee, Deborah; Campbell, Rebecca; Kubiak, Sheryl Pimlott; Sullivan, Cris

2012-09-01

As empirical evidence has demonstrated the pervasiveness of sexual assault and intimate partner violence in the lives of women, and the links to poor mental health outcomes, attention has turned to examining how women seek and access formal help. We present a conceptual model that addresses prior limitations and makes three key contributions: It foregrounds the influence of social location and multiple contextual factors; emphasizes the importance of the attainment of effective formal help that meets women's needs and leads to positive mental health outcomes; and highlights the role of interventions in facilitating help attainment. We conclude with research and practice implications.

Constraining eye movement in individuals with Parkinson's disease during walking turns.

Science.gov (United States)

Ambati, V N Pradeep; Saucedo, Fabricio; Murray, Nicholas G; Powell, Douglas W; Reed-Jones, Rebecca J

2016-10-01

Walking and turning is a movement that places individuals with Parkinson's disease (PD) at increased risk for fall-related injury. However, turning is an essential movement in activities of daily living, making up to 45 % of the total steps taken in a given day. Hypotheses regarding how turning is controlled suggest an essential role of anticipatory eye movements to provide feedforward information for body coordination. However, little research has investigated control of turning in individuals with PD with specific consideration for eye movements. The purpose of this study was to examine eye movement behavior and body segment coordination in individuals with PD during walking turns. Three experimental groups, a group of individuals with PD, a group of healthy young adults (YAC), and a group of healthy older adults (OAC), performed walking and turning tasks under two visual conditions: free gaze and fixed gaze. Whole-body motion capture and eye tracking characterized body segment coordination and eye movement behavior during walking trials. Statistical analysis revealed significant main effects of group (PD, YAC, and OAC) and visual condition (free and fixed gaze) on timing of segment rotation and horizontal eye movement. Within group comparisons, revealed timing of eye and head movement was significantly different between the free and fixed gaze conditions for YAC (p  0.05). In addition, while intersegment timings (reflecting segment coordination) were significantly different for YAC and OAC during free gaze (p training programs for those with PD, possibly promoting better coordination during turning and potentially reducing the risk of falls.

Source term analysis for a RCRA mixed waste disposal facility

International Nuclear Information System (INIS)

Jordan, D.L.; Blandford, T.N.; MacKinnon, R.J.

1996-01-01

A Monte Carlo transport scheme was used to estimate the source strength resulting from potential releases from a mixed waste disposal facility. Infiltration rates were estimated using the HELP code, and transport through the facility was modeled using the DUST code, linked to a Monte Carlo driver

On the evolving portfolio of community-standards and data sharing policies: turning challenges into new opportunities

Directory of Open Access Journals (Sweden)

Sansone Susanna-Assunta

2012-07-01

Full Text Available Abstract There are thousands of biology databases with hundreds of terminologies, reporting guidelines, representations models, and exchange formats to help annotate, report, and share bioscience investigations. It is evident, however, that researchers and bioinformaticians struggle to navigate the various standards and to find the appropriate database to collect, manage, and share data. Further, policy makers, funders, and publishers lack sufficient information to formulate their guidelines. In this paper, we highlight a number of key issues that can be used to turn these challenges into new opportunities. It is time for all stakeholders to work together to reconcile cause and effect and make the data-sharing culture functional and efficient.

'Help me! I'm old!' How negative aging stereotypes create dependency among older adults.

Science.gov (United States)

Coudin, Genevieve; Alexopoulos, Theodore

2010-07-01

This study examined the effects of negative aging stereotypes on self-reported loneliness, risk-taking, subjective health, and help-seeking behavior in a French sample of older adults. The aim of this study was to show the detrimental effects of negative aging stereotypes on older adults' self-evaluations and behaviors, therefore contributing to the explanations of the iatrogenic effect of social environments that increase dependency (e.g., health care institutions). In the first experiment conducted on 57 older adults, we explored the effects of positive, neutral, or negative stereotype activation on the feeling of loneliness and risk taking decision. The second experiment (n = 60) examined the impact of stereotype activation on subjective health, self-reported extraversion as well as on a genuine help-seeking behavior, by allowing participants to ask for the experimenter's help while completing a task. As predicted, negative stereotype activation resulted in lower levels of risk taking, subjective health and extraversion, and in higher feelings of loneliness and a more frequent help-seeking behavior. These findings suggest that the mere activation of negative stereotypes can have broad and deleterious effects on older individuals' self-evaluation and functioning, which in turn may contribute to the often observed dependency among older people.

Computation of the Coupling Resonance Driving term f1001 and the coupling coefficient C from turn-by-turn single-BPM data.

CERN Document Server

Franchi, A; Vanbavinkhove, G; CERN. Geneva. BE Department

2010-01-01

In this note we show how to compute the Resonance Driving Term (RDT) f1001, the local resonance term chi 1010 and the coupling coefficient C from the spectrum of turn-by-turn single-BPM data. The harmonic analysis of real coordinate x(y) is model independent, conversely to the the analysis of the complex Courant-Snyder coordinate hx,- = x-ipx. From the computation of f1001 along the ring is closely related to the global coupling coefficient C, but it is affected by an intrinsic error, discussed in this note.

Turn-Taking Based on Information Flow for Fluent Human-Robot Interaction

OpenAIRE

Thomaz, Andrea L.; Chao, Crystal

2011-01-01

Turn-taking is a fundamental part of human communication. Our goal is to devise a turn-taking framework for human-robot interaction that, like the human skill, represents something fundamental about interaction, generic to context or domain. We propose a model of turn-taking, and conduct an experiment with human subjects to inform this model. Our findings from this study suggest that information flow is an integral part of human floor-passing behavior. Following this, we implement autonomous ...

Roles of beta-turns in protein folding: from peptide models to protein engineering.

Science.gov (United States)

Marcelino, Anna Marie C; Gierasch, Lila M

2008-05-01

Reverse turns are a major class of protein secondary structure; they represent sites of chain reversal and thus sites where the globular character of a protein is created. It has been speculated for many years that turns may nucleate the formation of structure in protein folding, as their propensity to occur will favor the approximation of their flanking regions and their general tendency to be hydrophilic will favor their disposition at the solvent-accessible surface. Reverse turns are local features, and it is therefore not surprising that their structural properties have been extensively studied using peptide models. In this article, we review research on peptide models of turns to test the hypothesis that the propensities of turns to form in short peptides will relate to the roles of corresponding sequences in protein folding. Turns with significant stability as isolated entities should actively promote the folding of a protein, and by contrast, turn sequences that merely allow the chain to adopt conformations required for chain reversal are predicted to be passive in the folding mechanism. We discuss results of protein engineering studies of the roles of turn residues in folding mechanisms. Factors that correlate with the importance of turns in folding indeed include their intrinsic stability, as well as their topological context and their participation in hydrophobic networks within the protein's structure.

Measurement of tool forces in diamond turning

Energy Technology Data Exchange (ETDEWEB)

Drescher, J.; Dow, T.A.

1988-12-01

A dynamometer has been designed and built to measure forces in diamond turning. The design includes a 3-component, piezoelectric transducer. Initial experiments with this dynamometer system included verification of its predicted dynamic characteristics as well as a detailed study of cutting parameters. Many cutting experiments have been conducted on OFHC Copper and 6061-T6 Aluminum. Tests have involved investigation of velocity effects, and the effects of depth and feedrate on tool forces. Velocity has been determined to have negligible effects between 4 and 21 m/s. Forces generally increase with increasing depth of cut. Increasing feedrate does not necessarily lead to higher forces. Results suggest that a simple model may not be sufficient to describe the forces produced in the diamond turning process.

Kinematical Comparison of the 200 m Backstroke Turns between National and Regional Level Swimmers

Science.gov (United States)

Veiga, Santiago; Cala, Antonio; Frutos, Pablo González; Navarro, Enrique

2013-01-01

The aims of this investigation were to determine the evolution of selected turn variables during competitive backstroke races and to compare these kinematic variables between two different levels of swimmers. Sixteen national and regional level male swimmers participant in the 200 m backstroke event at the Spanish Swimming Championships in short course (25 m) were selected to analyze their turn performances. The individual distances method with two-dimensional Direct Linear Transformation (2D-DLT) algorithms was used to perform race analyses. National level swimmers presented a shorter “turn time”, a longer “distance in”, a faster “underwater velocity” and “normalized underwater velocity”, and a faster “stroking velocity” than regional level swimmers, whereas no significant differences were detected between levels for the “underwater distance”. National level swimmers maintained similar “turn times” over the event and increased “underwater velocity” and “normalized underwater velocity” in the last (seventh) turn segment, whereas regional level swimmers increased “turn time” in the last half of the race. For both national and regional level swimmers, turn “underwater distance” during the last three turns of the race was significantly shorter while no significant differences in distance into the wall occurred throughout the race. The skill level of the swimmers has an impact on the competitive backstroke turn segments. In a 200 m event, the underwater velocity should be maximized to maintain turn proficiency, whereas turn distance must be subordinated to the average velocity. Key Points The underwater turn velocity is as a critical variable related to the swimmers’ level of skill in a 200 m backstroke event. Best swimmers perform faster but no longer turn segments during a 200 m backstroke event. Best swimmers maintain their turn performance throughout the 200 m backstroke event by increasing the underwater velocity

Part-turn gearboxes for electric actuators; Schwenkgetriebe fuer elektrische Stellantriebe

Energy Technology Data Exchange (ETDEWEB)

Herbstritt, M. [Riester (W.) GmbH und Co. KG, Muellheim (Germany)

2002-09-01

Different types of gearboxes provide a useful complement to the electric actuator type ranges. The gearboxes can be combined with the actuators in many ways. Multi-turn actuators, for example, can be turned into part-turn actuators. When using a modular system, a suitable solution for almost any automation task in the field of industrial valves can be found. (orig.) [German] Sinnvoll ergaenzt werden elektrische Stellantriebe fuer Armaturen durch verschiedene Arten von Getrieben. Die Getriebe sind in vielfaeltiger Weise mit den Stellantrieben kombinierbar. So werden beispielsweise aus Drehantrieben Schwenkantriebe. Mit einem Baukasten-System laesst sich so fuer nahezu jede Automatisierungsaufgabe im Bereich der Industriearmaturen eine passende Loesung finden. (orig.)

Universal compact lower limb turning module intended for use in orthotic robots

Directory of Open Access Journals (Sweden)

Janowski Mateusz

2018-01-01

Full Text Available In this paper, a model of an orthotic robot’s lower limb rotation system is presented. The system is intended for use in typical contemporary orthotic robots such as the ‘Veni-Prometheus’ System for Verticalization and Aiding Motion designed at the Faculty of Mechatronics, Warsaw University of Technology. In the paper, the state of the art is briefly stated, with the relatively low number of orthotic robots allowing realization of pivoting turns highlighted. The intended two-stage pivoting turning movement is analyzed in detail and the operating conditions as well as limitations of the turning module are indicated. The conception of a turning module introduces additional degree of freedom to the existing orthotic robot designs by realizing the rotation about the lengthwise axis in the thigh link. A three-dimensional model and its analysis are shown. The proposed design ensures the necessary movement of the lower limb and the torso of an impaired person during the execution of pivoting turn while remaining compact in order to ease the introduction of the turning system to different orthotic robot designs.

Analyses of quenching process during turn-off of plasma electrolytic carburizing on carbon steel

International Nuclear Information System (INIS)

Wu, Jie; Liu, Run; Xue, Wenbin; Wang, Bin; Jin, Xiaoyue; Du, Jiancheng

2014-01-01

Highlights: • Cooling rate of carburized steel at the end of PEC treatment is measured. • The quench hardening in the fast or slow turn-off mode hardly takes place. • Decrease of the surface roughness during slow turn-off process is found. • A slow turn-off mode is recommended to replace the conventional turn-off mode. - Abstract: Plasma electrolytic carburizing (PEC) under different turn-off modes was employed to fabricate a hardening layer on carbon steel in glycerol solution without stirring at 380 V for 3 min. The quenching process in fast turn-off mode or slow turn-off mode of power supply was discussed. The temperature in the interior of steel and electron temperature in plasma discharge envelope during the quenching process were evaluated. It was found that the cooling rates of PEC samples in both turn-off modes were below 20 °C/s, because the vapor film boiling around the steel sample reduced the cooling rate greatly in terms of Leidenfrost effect. Thus the quench hardening hardly took place, though the slow turn-off mode slightly decreased the surface roughness of PEC steel. At the end of PEC treatment, the fast turn-off mode used widely at present cannot enhance the surface hardness by quench hardening, and the slow turn-off mode was recommended in order to protect the electronic devices against a large current surge

A Practice Turn for Teacher Education?

Science.gov (United States)

Reid, Jo-Anne

2011-01-01

Within the Research Institute for Professional Practice, Learning and Education (RIPPLE) at Charles Sturt University, teacher education researchers have been quick to respond to the opportunities created by what is known as "the practice turn" that characterises contemporary theory around the globe and across disciplines. We are working,…

The Dynamic Turn in Quantum Logic

NARCIS (Netherlands)

Baltag, A.; Smets, S.

2012-01-01

In this paper we show how ideas coming from two areas of research in logic can reinforce each other. The first such line of inquiry concerns the "dynamic turn" in logic and especially the formalisms inspired by Propositional Dynamic Logic (PDL); while the second line concerns research into the

The dynamic turn in quantum logic

NARCIS (Netherlands)

Baltag, Alexandru; Smets, Sonja

In this paper we show how ideas coming from two areas of research in logic can reinforce each other. The first such line of inquiry concerns the "dynamic turn" in logic and especially the formalisms inspired by Propositional Dynamic Logic (PDL); while the second line concerns research into the

Novel β-amyloid aggregation inhibitors possessing a turn mimic.

Science.gov (United States)

Hamada, Yoshio; Miyamoto, Naoko; Kiso, Yoshiaki

2015-04-01

Amyloid β peptide, the main component of senile plaques found in the brain of Alzheimer disease (AD) patients, is a molecular target for AD therapeutic intervention. A number of potential AD therapeutics have been reported, including inhibitors of β-secretase, γ-secretase, and Aβ aggregation, and anti-amyloid agents, such as neprilysin, insulin degrading enzyme (IDE), and Aβ antibodies. Recently, we reported potent small-sized β-secretase (BACE1) inhibitors, which could serve as anti-AD drugs. However AD is a progressive disorder, where dementia symptoms gradually worsen over several decades, and therefore may require many years to get cured. One possible way to achieve a greater therapeutic effect is through simultaneous administration of multiple drugs, similar to those used in Highly Active Anti-Retroviral Therapy (HAART) used to treat AIDS. In order to overcome AD, we took a drug discovery approach to evaluate, novel β-amyloid aggregation inhibitors. Previously, we reported that a tong-type compound possessing a turn mimic as the inhibitor of HIV-1 protease dimerization. Oligomerized amyloid β peptides contain a turn structure within the molecule. Here, we designed and synthesized novel β-amyloid aggregation inhibitors with a turn-mimic template, based on the turn conformer of the oligomerized amyloid β peptides. Copyright © 2015 Elsevier Ltd. All rights reserved.

A high performance gate drive for large gate turn off thyristors

Energy Technology Data Exchange (ETDEWEB)

Szilagyi, C.P.

1993-01-01

Past approaches to gate turn-off (GTO) gating are application oriented, inefficient and dissipate power even when inactive. They allow the gate to avalanch, and do not reduce GTO turn-on and turn-off losses. A new approach is proposed which will allow modular construction and adaptability to large GTOs in the 50 amp to 2000 amp range. The proposed gate driver can be used in large voltage source and current source inverters and other power converters. The approach consists of a power metal-oxide-silicon field effect transistor (MOSFET) technology gating unit, with associated logic and supervisory circuits and an isolated flyback converter as the dc power source for the gating unit. The gate driver formed by the gating unit and the flyback converter is designed for 4000 V isolation. Control and supervisory signals are exchanged between the gate driver and the remote control system via fiber optics. The gating unit has programmable front-porch current amplitude and pulse-width, programmable closed-loop controlled back-porch current, and a turn-off switch capable of supplying negative gate current at demand as a function of peak controllable forward anode current. The GTO turn-on, turn-off and gate avalanch losses are reduced to a minimum. The gate driver itself has minimum operating losses. Analysis, design and practical realization are reported. 19 refs., 54 figs., 1 tab.

Turn-on delay of QD and QW laser diodes: What is the difference?

International Nuclear Information System (INIS)

Sokolovskii, G S; Dudelev, V V; Kolykhalova, E D; Deryagin, A G; Maximov, M V; Nadtochiy, A M; Kuchinskii, V I; Mikhrin, S S; Livshits, D A; Viktorov, E A; Erneux, T

2013-01-01

Turn-on delay of laser diodes with quantum-sized active media is investigated both theoretically and experimentally. In this research we show the striking difference in turn-on delay of quantum dot and quantum well laser diodes: With quantum-well lasers turn on delay tends to zero in the limit of high pumping, while with quantum dot lasers turn-on delay has the non-vanishing component which is independent of pumping

Extended phenotype: nematodes turn ants into bird-dispersed fruits

DEFF Research Database (Denmark)

Hughes, D P; Kronauer, D J C; Boomsma, J J

2008-01-01

A recent study has discovered a novel extended phenotype of a nematode which alters its ant host to resemble ripe fruit. The infected ants are in turn eaten by frugivorous birds that disperse the nematode's eggs.......A recent study has discovered a novel extended phenotype of a nematode which alters its ant host to resemble ripe fruit. The infected ants are in turn eaten by frugivorous birds that disperse the nematode's eggs....

Virtual turning points

CERN Document Server

Honda, Naofumi; Takei, Yoshitsugu

2015-01-01

The discovery of a virtual turning point truly is a breakthrough in WKB analysis of higher order differential equations. This monograph expounds the core part of its theory together with its application to the analysis of higher order Painlevé equations of the Noumi–Yamada type and to the analysis of non-adiabatic transition probability problems in three levels. As M.V. Fedoryuk once lamented, global asymptotic analysis of higher order differential equations had been thought to be impossible to construct. In 1982, however, H.L. Berk, W.M. Nevins, and K.V. Roberts published a remarkable paper in the Journal of Mathematical Physics indicating that the traditional Stokes geometry cannot globally describe the Stokes phenomena of solutions of higher order equations; a new Stokes curve is necessary.

Turning lead into gold

DEFF Research Database (Denmark)

Jensen, Steffen Moltrup Ernø

For years the field of entrepreneurship has been blinded by the alchemical promise of turning lead into gold, of finding the ones most likely to become the next Branson, Zuckerberg or Gates. The promise has been created in the midst of political and scientific agendas where certain individuals...... is not to accumulate state or market wealth, but for entrepreneurial skills to become tools towards the liberation of the individual from oppressive systems of control – essentially to add public value rather than economic value. In this presentation I will sketch an anarchist perspective on entrepreneurship, looking...

Greywater turns to gold: Treatment units to help low-income ...

International Development Research Centre (IDRC) Digital Library (Canada)

2011-02-08

Feb 8, 2011 ... In Jordan, the demand for freshwater already exceeds the supply. With no new sources to tap, Jordanians must find ways to reduce their demand and make better use of existing supplies. One of option being pursued is greywater reuse. In a series of projects supported by Canada's International ...

Help-Seeking and Help-Giving for Teen Dating Violence

Science.gov (United States)

Weisz, Arlene N.; Black, Beverly M.

2009-01-01

This article is based on numerous research projects conducted by the authors on adolescent dating violence. It reviews the results of those projects as they relate to how teens seek help for dating violence and how teens provide help to their friends in violent dating relationships. It concludes with helpful strategies for adults who work with…

Coordination of groundwater activities in the 100 N Area

International Nuclear Information System (INIS)

Hartman, M.J.

1995-09-01

The initiation of the N Springs Expedited Response Action (ERA) in the 100 N Area will affect the groundwater monitoring networks of two Resource Conservation and Recovery Act of 1976 (RCRA) units. The 1301-N and 325-N facilities are treatment, storage, or disposal (TSD) units that have been monitored under RCRA since 1987. In September 1994, the Washington State Department of Ecology issued an action memorandum, instructing the US Department of Energy (DOE) to take the action. The planned pump-and-treat system will preclude meeting the specific objectives of interim-status RCRA groundwater monitoring representative samples and detect adverse impacts of the TSD units on. However, under RCRA final-status requirements, which will be implemented in 1999, corrective action for groundwater contamination will probably be required. The US Environmental Protection Agency (EPA) has declared parity between RCRA corrective action and Comprehensive Environmental Response, Compensation, and Liability Act of 1980 remedial action decisions. The 1301-N and 1325-N facilities are still in interim-status and therefore are not in the category of ''RCRA corrective action.'' However, DOE's position is that parity exists between RCRA and the ERA because RCRA corrective action will almost certainly be required in the future

The Timed 180° Turn Test for Assessing People with Hemiplegia from Chronic Stroke

Directory of Open Access Journals (Sweden)

Regan L. Robinson

2018-01-01

Full Text Available Background. Turning is ubiquitous in activities of daily living. For people with hemiplegia, persistent impairments in strength, balance, and coordination will affect their ability to turn safely. Consequently, turning retraining should be addressed in rehabilitation programs. To measure turning for these individuals, a reliable clinical tool is required. Objective. To investigate (i the intrarater, interrater, and test-retest reliability of the timed 180° turn test; (ii the correlation of the timed 180° turn test with other measures of stroke-specific impairments; and (iii the cut-off time that best discriminates individuals with hemiplegia from chronic stroke and healthy older adults. Methods. 33 individuals with hemiplegia due to chronic stroke and 32 healthy elderly individuals participated in this cross-sectional study. The timed 180° turn test was administered along with other measures of stroke-specific impairment. Results. The timed 180° turn test demonstrated excellent intrarater, interrater, and test-retest reliability in individuals with hemiplegia from chronic stroke. The timed 180° turn test (times significantly correlated with the Fugl-Meyer Assessment of the Lower Extremities (FMA-LE, affected ankle plantar flexion strength, the 5-Times-Sit-To-Stand test, the Berg Balance Scale (BBS, and the Timed Up and Go (TUG test. Conclusion. The timed 180° turn test is a reliable clinical tool to assess the turning ability of subjects with hemiplegia from chronic stroke.

Turning points in reactor design

International Nuclear Information System (INIS)

Beckjord, E.S.

1995-01-01

This article provides some historical aspects on nuclear reactor design, beginning with PWR development for Naval Propulsion and the first commercial application at Yankee Rowe. Five turning points in reactor design and some safety problems associated with them are reviewed: (1) stability of Dresden-1, (2) ECCS, (3) PRA, (4) TMI-2, and (5) advanced passive LWR designs. While the emphasis is on the thermal-hydraulic aspects, the discussion is also about reactor systems

Turning points in reactor design

Energy Technology Data Exchange (ETDEWEB)

Beckjord, E.S.

1995-09-01

This article provides some historical aspects on nuclear reactor design, beginning with PWR development for Naval Propulsion and the first commercial application at Yankee Rowe. Five turning points in reactor design and some safety problems associated with them are reviewed: (1) stability of Dresden-1, (2) ECCS, (3) PRA, (4) TMI-2, and (5) advanced passive LWR designs. While the emphasis is on the thermal-hydraulic aspects, the discussion is also about reactor systems.

In silico platform for predicting and initiating β-turns in a protein at desired locations.

Science.gov (United States)

Singh, Harinder; Singh, Sandeep; Raghava, Gajendra P S

2015-05-01

Numerous studies have been performed for analysis and prediction of β-turns in a protein. This study focuses on analyzing, predicting, and designing of β-turns to understand the preference of amino acids in β-turn formation. We analyzed around 20,000 PDB chains to understand the preference of residues or pair of residues at different positions in β-turns. Based on the results, a propensity-based method has been developed for predicting β-turns with an accuracy of 82%. We introduced a new approach entitled "Turn level prediction method," which predicts the complete β-turn rather than focusing on the residues in a β-turn. Finally, we developed BetaTPred3, a Random forest based method for predicting β-turns by utilizing various features of four residues present in β-turns. The BetaTPred3 achieved an accuracy of 79% with 0.51 MCC that is comparable or better than existing methods on BT426 dataset. Additionally, models were developed to predict β-turn types with better performance than other methods available in the literature. In order to improve the quality of prediction of turns, we developed prediction models on a large and latest dataset of 6376 nonredundant protein chains. Based on this study, a web server has been developed for prediction of β-turns and their types in proteins. This web server also predicts minimum number of mutations required to initiate or break a β-turn in a protein at specified location of a protein. © 2015 Wiley Periodicals, Inc.

78 FR 25678 - Georgia: Final Authorization of State Hazardous Waste Management Program Revisions

Science.gov (United States)

2013-05-02

...: Final Authorization of State Hazardous Waste Management Program Revisions AGENCY: Environmental... of changes to its hazardous waste program under the Resource Conservation and Recovery Act (RCRA... Gwendolyn Gleaton, Permits and State Programs Section, RCRA Programs and Materials Management Branch, RCRA...

76 FR 6594 - Florida: Final Authorization of State Hazardous Waste Management Program Revisions

Science.gov (United States)

2011-02-07

...: Final Authorization of State Hazardous Waste Management Program Revisions AGENCY: Environmental... of the changes to its hazardous waste program under the Resource Conservation and Recovery Act (RCRA... and State Programs Section, RCRA Programs and Materials Management Branch, RCRA Division, U.S...

77 FR 60963 - Tennessee: Final Authorization of State Hazardous Waste Management Program Revisions

Science.gov (United States)

2012-10-05

...: Final Authorization of State Hazardous Waste Management Program Revisions AGENCY: Environmental... of the changes to its hazardous waste program under the Resource Conservation and Recovery Act (RCRA... Johnson, Permits and State Programs Section, RCRA Programs and Materials Management Branch, RCRA Division...

Racial and ethnic minority college students' stigma associated with seeking psychological help: Examining psychocultural correlates.

Science.gov (United States)

Cheng, Hsiu-Lan; Kwan, Kwong-Liem Karl; Sevig, Todd

2013-01-01

Many college students underuse professional psychological help for mental health difficulties. The stigma associated with seeking such help appears to be one of the reasons for this underuse. Levels of psychological distress and past use of counseling/psychotherapy have been found to be important correlates of stigma associated with seeking psychological help (Obasi & Leong, 2009; Vogel, Wade, & Haake, 2006). For racial and ethnic minorities, the hindering effects of self-stigma and perceived stigmatization by others on treatment seeking may further be compounded by their relationships with their own ethnic groups, with other ethnic groups, and with the dominant society. This study used structural equation modeling (SEM) to test a model that explored the effects of psychological distress and psychocultural variables (i.e., ethnic identity, other-group orientation, perceived discrimination) on perceived stigmatization by others and self-stigma for seeking psychological help, controlling for past use of counseling/psychotherapy. The sample consisted of 260 African American, 166 Asian American, and 183 Latino American students. SEM multigroup analyses indicated measurement invariance, but partial structural invariance, across racial/ethnic groups. Across all 3 groups, higher levels of psychological distress and perceived racial/ethnic discrimination, respectively, predicted higher levels of perceived stigmatization by others for seeking psychological help, which, in turn, predicted greater self-stigma for seeking psychological help. Higher levels of other-group orientation predicted lower levels of self-stigma of seeking psychological help across groups. Higher levels of ethnic identity predicted lower levels of self-stigma of seeking psychological help only for African Americans. Implications for research and practice are discussed. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Kinematical Comparison of the 200 m Backstroke Turns between National and Regional Level Swimmers

Directory of Open Access Journals (Sweden)

Santiago Veiga

2013-12-01

Full Text Available The aims of this investigation were to determine the evolution of selected turn variables during competitive backstroke races and to compare these kinematic variables between two different levels of swimmers. Sixteen national and regional level male swimmers participant in the 200 m backstroke event at the Spanish Swimming Championships in short course (25 m were selected to analyze their turn performances. The individual distances method with two-dimensional Direct Linear Transformation (2D-DLT algorithms was used to perform race analyses. National level swimmers presented a shorter “turn time”, a longer “distance in”, a faster “underwater velocity” and “normalized underwater velocity”, and a faster “stroking velocity” than regional level swimmers, whereas no significant differences were detected between levels for the “underwater distance”. National level swimmers maintained similar “turn times” over the event and increased “underwater velocity” and “normalized underwater velocity” in the last (seventh turn segment, whereas regional level swimmers increased “turn time” in the last half of the race. For both national and regional level swimmers, turn “underwater distance” during the last three turns of the race was significantly shorter while no significant differences in distance into the wall occurred throughout the race. The skill level of the swimmers has an impact on the competitive backstroke turn segments. In a 200 m event, the underwater velocity should be maximized to maintain turn proficiency, whereas turn distance must be subordinated to the average velocity.

Prediction of beta-turns in proteins using the first-order Markov models.

Science.gov (United States)

Lin, Thy-Hou; Wang, Ging-Ming; Wang, Yen-Tseng

2002-01-01

We present a method based on the first-order Markov models for predicting simple beta-turns and loops containing multiple turns in proteins. Sequences of 338 proteins in a database are divided using the published turn criteria into the following three regions, namely, the turn, the boundary, and the nonturn ones. A transition probability matrix is constructed for either the turn or the nonturn region using the weighted transition probabilities computed for dipeptides identified from each region. There are two such matrices constructed for the boundary region since the transition probabilities for dipeptides immediately preceding or following a turn are different. The window used for scanning a protein sequence from amino (N-) to carboxyl (C-) terminal is a hexapeptide since the transition probability computed for a turn tetrapeptide is capped at both the N- and C- termini with a boundary transition probability indexed respectively from the two boundary transition matrices. A sum of the averaged product of the transition probabilities of all the hexapeptides involving each residue is computed. This is then weighted with a probability computed from assuming that all the hexapeptides are from the nonturn region to give the final prediction quantity. Both simple beta-turns and loops containing multiple turns in a protein are then identified by the rising of the prediction quantity computed. The performance of the prediction scheme or the percentage (%) of correct prediction is evaluated through computation of Matthews correlation coefficients for each protein predicted. It is found that the prediction method is capable of giving prediction results with better correlation between the percent of correct prediction and the Matthews correlation coefficients for a group of test proteins as compared with those predicted using some secondary structural prediction methods. The prediction accuracy for about 40% of proteins in the database or 50% of proteins in the test set is

Egg turning behavior and incubation temperature in Forster’s terns in relation to mercury contamination

Science.gov (United States)

Taylor, Gregory T.; Ackerman, Joshua T.; Shaffer, Scott A.

2018-01-01

Egg turning behavior is an important determinant of egg hatchability, but it remains relatively understudied. Here, we examined egg turning rates and egg temperatures in Forster’s terns (Sterna forsteri). We used artificial eggs containing a data logger with a 3-D accelerometer, a magnetometer, and a temperature thermistor to monitor parental incubation behavior of 131 tern nests. Overall, adults turned their eggs an average (±SD) of 3.8 ± 0.8 turns h-1, which is nearly two times higher than that of other seabirds. Egg turning rates increased with nest initiation date. We also examined egg turning rates and egg temperatures in relation to egg mercury contamination. Mercury contamination has been shown to be associated with reduced egg hatchability, and we hypothesized that mercury may decrease egg hatchability via altered egg turning behavior by parents. Despite the high variability in egg turning rates among individuals, the rate of egg turning was not related to mercury concentrations in sibling eggs. These findings highlight the need for further study concerning the potential determinants of egg turning behavior.

Treatment of uranium turning with the controllable oxidizing process

International Nuclear Information System (INIS)

Shen Bingyi; Zhang Yonggang; Zhen Huikuan

1989-02-01

The concept, procedure and safety measures of the controllable oxidizing for uranium turning is described. The feasibility study on technological process has been made. The process provided several advantages such as: simplicity of operation, no pollution environment, safety, high efficiency and low energy consumption. The process can yield nuclear pure uranium dioxide under making no use of a great number of chemical reagent. It may supply raw material for fluoration and provide a simply method of treatment for safe store of uranium turning

Annual Hanford Site environmental permitting status report

International Nuclear Information System (INIS)

Sonnichsen, J.C.

1998-01-01

The information contained and/or referenced in this Annual Hanford Site Environmental Permitting Status Report (Status Report) addresses the State Environmental Policy Act (SEPA) of 1971 and Condition II.W. of the Resource Conservation and Recovery Act (RCRA) of 1976 Permit, Dangerous Waste Portion (DW Portion). Condition II.W. of the RCRA Permit specifies the Permittees are responsible for all other applicable federal, state, and local permits for the development and operation of the Hanford Facility. Condition II.W. of the RCRA Permit specifies that the Permittees are to use their best efforts to obtain such permits. For the purposes of permit condition, 'best efforts' means submittal of documentation and/or approval(s) in accordance with schedules specified in applicable regulations, or as determined through negotiations with the applicable regulatory agencies. This Status Report includes information on all existing and anticipated environmental permitting. Environmental permitting required by RCRA, the Hazardous and Solid Waste Amendments (HSWA) of 1984, and non-RCRA permitting (solid waste handling, Clean Air Act Amendments of 1990, Clean Water Act Amendments of 1987, Washington State waste discharge, and onsite sewage system) is addressed. Information on RCRA and non-RCRA is current as of July 31, 1998. For the purposes of RCRA and the State of Washington Hazardous Waste Management Act of 1976 [as administered through the Dangerous Waste Regulations, Washington Active Code (WAC) 173-303], the Hanford Facility is considered a single facility. As such, the Hanford Facility has been issued one US Environmental Protection Agency (EPA)/State Identification Number (WA7890008967). This EPA/State identification number encompasses over 60 treatment, storage, and/or disposal (TSD) units. The Washington State Department of Ecology (Ecology) has been delegated authority by the EPA to administer the RCRA, including mixed waste authority. The RCRA permitting approach for

Turning Technology into Business Using University Patents

NARCIS (Netherlands)

Hartmann, L.

2014-01-01

We present an education paradigm that stimulates innovation and entrepreneurship through a master's-level university course: "Turning Technology into Business". The course was specifically designed to connect technological research with education using patented technologies developed at the research

Competence skills help deter smoking among inner city adolescents.

Science.gov (United States)

Epstein, J A; Griffin, K W; Botvin, G J

2000-03-01

To test whether higher levels of general competence are linked to more frequent use of refusal assertiveness that is in turn related to less subsequent smoking among inner city adolescents. Longitudinal study conducted during three year middle school or junior high school period. A sample of 1459 students attending 22 middle (ages 11-14 years) and junior high (ages 12-15 years) schools in New York City participated. Students completed surveys at baseline, one year follow up, and two year follow up. The students self reported smoking, decision making skills, personal efficacy, and refusal assertiveness. Teams of three to five data collectors administered the questionnaire following a standardised protocol. These data were collected in school during a regular 40 minute class period. Based on the tested structural equation model, decision making and personal efficacy (that is, general competence) predicted higher refusal assertiveness and this greater assertiveness predicted less smoking at the two year follow up. The tested model had a good fit and was parsimonious and consistent with theory. Adolescent smoking prevention programmes often teach refusal skills in order to help youth resist peer pressure to smoke. The present findings suggest that teaching general competence skills as well may help to reduce smoking because youth with better personal efficacy and decision making skills are better able to implement smoking refusal strategies.

Towards a Practice Turn in EU Studies

DEFF Research Database (Denmark)

Adler-Nissen, Rebecca

2016-01-01

This article explores how practice theory can be recruited for the study of European integration. New generations of EU researchers are fascinated by the prospect of leaving the armchair and studying the people and artefacts that make the EU on an everyday level. This article surveys key practice......-oriented, anthropological and micro-sociological studies of the EU and European integration and shows how their findings challenge more traditional understandings of the dynamics of European integration. Moving beyond a stock-taking, the article distinguishes between ‘order- ing’ and ‘disordering’ practices and explores...... the potential of a practice turn in EU studies for both theory (overcoming dualism, replacing substantialism with processualism and rethinking power) and methods (including unstructured interviews, fieldwork and participant observation). A practice turn will force us to rethink core assumptions about the EU...

Anticipated Guilt for not Helping and Anticipated Warm Glow for Helping are Differently Impacted by Personal Responsibility to Help

Directory of Open Access Journals (Sweden)

Arvid Erlandsson

2016-09-01

Full Text Available One important motivation for people behaving prosocially is that they want to avoid negative and obtain positive emotions. In the prosocial behavior literature however, the motivations to avoid negative emotions (e.g. guilt and to approach positive emotions (e.g. warm glow are rarely separated, and sometimes even aggregated into a single mood-management construct. The aim of this study was to investigate whether anticipated guilt if not helping and anticipated warm glow if helping are influenced similarly or differently when varying situational factors related to personal responsibility to help. Helping scenarios were created and pilot tests established that each helping scenario could be formulated both in a high-responsibility version and in a low-responsibility version. In Study 1 participants read high-responsibility and low-responsibility helping scenarios, and rated either their anticipated guilt if not helping or their anticipated warm glow if helping (i.e. separate evaluation. Study 2 was similar but here participants rated both their anticipated guilt if not helping and their anticipated warm glow if helping (i.e. joint evaluation. Anticipated guilt was clearly higher in the high-responsibility versions, but anticipated warm glow was unaffected (in Studies 1a and 1b, or even higher in the low-responsibility versions (Study 2. In Studies 3 (where anticipated guilt and warm glow were evaluated separately and 4 (where they were evaluated jointly, personal responsibility to help was manipulated within-subjects. Anticipated guilt was again constantly higher in the high-responsibility versions but for many types of responsibility-manipulations, anticipated warm glow was higher in the low-responsibility versions. The results suggest that we anticipate guilt if not fulfilling our responsibility but that we anticipate warm glow primarily when doing over and beyond our responsibility. We argue that future studies investigating motivations for

Anticipated Guilt for Not Helping and Anticipated Warm Glow for Helping Are Differently Impacted by Personal Responsibility to Help

Science.gov (United States)

Erlandsson, Arvid; Jungstrand, Amanda Å.; Västfjäll, Daniel

2016-01-01

One important motivation for people behaving prosocially is that they want to avoid negative and obtain positive emotions. In the prosocial behavior literature however, the motivations to avoid negative emotions (e.g., guilt) and to approach positive emotions (e.g., warm glow) are rarely separated, and sometimes even aggregated into a single mood-management construct. The aim of this study was to investigate whether anticipated guilt if not helping and anticipated warm glow if helping are influenced similarly or differently when varying situational factors related to personal responsibility to help. Helping scenarios were created and pilot tests established that each helping scenario could be formulated both in a high-responsibility version and in a low-responsibility version. In Study 1 participants read high-responsibility and low-responsibility helping scenarios, and rated either their anticipated guilt if not helping or their anticipated warm glow if helping (i.e., separate evaluation). Study 2 was similar but here participants rated both their anticipated guilt if not helping and their anticipated warm glow if helping (i.e., joint evaluation). Anticipated guilt was clearly higher in the high-responsibility versions, but anticipated warm glow was unaffected (in Studies 1a and 1b), or even higher in the low-responsibility versions (Study 2). In Studies 3 (where anticipated guilt and warm glow were evaluated separately) and 4 (where they were evaluated jointly), personal responsibility to help was manipulated within-subjects. Anticipated guilt was again constantly higher in the high-responsibility versions but for many types of responsibility-manipulations, anticipated warm glow was higher in the low-responsibility versions. The results suggest that we anticipate guilt if not fulfilling our responsibility but that we anticipate warm glow primarily when doing over and beyond our responsibility. We argue that future studies investigating motivations for helping

Perceptions of Help Given to Healthy Older Mothers by Adult Daughters: Ways of Initiating Help and Types of Help Given

Science.gov (United States)

Martini, Tanya S.; Grusec, Joan E.; Bernardini, Silvia Cortese

2003-01-01

Older mother-adult daughter dyads (N = 43) addressed two issues pertaining to the ways in which help is initiated (offered, requested, and imposed help) and type of help given (instrumental help, advice, and emotional support) a) mothers' reasoning about these aspects of help, and b) daughters' understanding of mothers' feelings. Both groups noted…

Diamond turning of thermoplastic polymers

Energy Technology Data Exchange (ETDEWEB)

Smith, E.; Scattergood, R.O.

1988-12-01

Single point diamond turning studies were made using a series of thermoplastic polymers with different glass transition temperatures. Variations in surface morphology and surface roughness were observed as a function of cutting speed. Lower glass transition temperatures facilitate smoother surface cuts and better surface finish. This can be attributed to the frictional heating that occurs during machining. Because of the very low glass transition temperatures in polymeric compared to inorganic glasses, the precision machining response can be very speed sensitive.

Effect of surface integrity of hard turned AISI 52100 steel on fatigue performance

International Nuclear Information System (INIS)

Smith, Stephen; Melkote, Shreyes N.; Lara-Curzio, Edgar; Watkins, Thomas R.; Allard, Larry; Riester, Laura

2007-01-01

This paper addresses the relationship between surface integrity and fatigue life of hard turned AISI 52100 steel (60-62 HRC), with grinding as a benchmark. The impact of superfinishing on the fatigue performance of hard turned and ground surfaces is also discussed. Specifically, the surface integrity and fatigue life of the following five distinct surface conditions are examined: hard turned with continuous white layer, hard turned with no white layer, ground, and superfinished hard turned and ground specimens. Surface integrity of the specimens is characterized via surface topography measurement, metallography, residual stress measurements, transmission electron microscopy (TEM), and nano-indentation tests. High cycle tension-tension fatigue tests show that the presence of white layer does not adversely affect fatigue life and that, on average, the hard turned surface performs as well or better than the ground surface. The effect of superfinishing is to exaggerate these differences in performance. The results obtained from this study suggest that the effect of residual stress on fatigue life is more significant than the effect of white layer. For the hard turned surfaces, the fatigue life is found to be directly proportional to both the surface compressive residual stress and the maximum compressive residual stress. Possible explanations for the observed effects are discussed

Help-seeking preferences in the area of mild cognitive impairment: comparing family physicians and the lay public.

Science.gov (United States)

Werner, Perla; Heinik, Jeremia; Giveon, Shmuel; Segel-Karpas, Dikla; Kitai, Eliezer

2014-01-01

Mild cognitive impairment (MCI) or mild neurocognitive disorder is a well-established clinical entity included in current diagnostic guidelines for Alzheimer's disease and in major psychiatric classifications. In all, a loosely defined concern obtained from conceptually different sources (the individual, a knowledgeable informant, or a clinician) regarding a decline in cognition and change in functioning constitutes a sine qua non for initiating diagnostics and providing therapy and support. This concern in practice may translate into complex proactive help-seeking behavior. A better understanding of help-seeking preferences is required in order to promote early detection and management. To compare help-seeking preferences of family physicians and the lay public in the area of MCI. A structured questionnaire was used to collect data from 197 family physicians (self-administered) and 517 persons aged 45 and over from the lay public (face to face). Information regarding familiarity with MCI and help-seeking preferences was assessed. The vast majority in both samples reported that family physician, spouse, and children are the most highly recommended sources of help-seeking. In regard to professional sources of help-seeking, a higher percentage of the physicians than the lay public sample consistently recommended seeking help from nurses and social workers and psychiatrists, but a higher percentage of the lay public recommended turning to a neurologist for help. There were both similarities and differences between family physicians and the lay public in their preferences regarding help-seeking for a person with MCI. Most prominent is the physicians' greater tendency to recommend professional sources of help-seeking. Understanding of help-seeking preferences of both physicians and lay persons might help overcome barriers for establishing diagnosis, receiving care, and improving communication between doctors and patients.

Surface Corrosion Resistance in Turning of Titanium Alloy

Directory of Open Access Journals (Sweden)

Rui Zhang

2015-01-01

Full Text Available This work addresses the issues associated with implant surface modification. We propose a method to form the oxide film on implant surfaces by dry turning to generate heat and injecting oxygen-rich gas at the turning-tool flank. The morphology, roughness, composition, and thickness of the oxide films in an oxygen-rich atmosphere were characterized using scanning electron microscopy, optical profiling, and Auger electron spectroscopy. Electrochemical methods were used to study the corrosion resistance of the modified surfaces. The corrosion resistance trends, analyzed relative to the oxide film thickness, indicate that the oxide film thickness is the major factor affecting the corrosion resistance of titanium alloys in a simulated body fluid (SBF. Turning in an oxygen-rich atmosphere can form a thick oxide film on the implant surface. The thickness of surface oxide films processed at an oxygen concentration of 80% was improved to 4.6 times that of films processed at an oxygen concentration of 21%; the free corrosion potential shifted positively by 0.357 V, which significantly improved the corrosion resistance of titanium alloys in the SBF. Therefore, the proposed method may (partially replace the subsequent surface oxidation. This method is significant for biomedical development because it shortens the process flow, improves the efficiency, and lowers the cost.

When attempts at robbing prey turn fatal

Science.gov (United States)

Dejean, Alain; Corbara, Bruno; Azémar, Frédéric; Carpenter, James M.

2012-07-01

Because group-hunting arboreal ants spread-eagle insect prey for a long time before retrieving them, these prey can be coveted by predatory flying insects. Yet, attempting to rob these prey is risky if the ant species is also an effective predator. Here, we show that trying to rob prey from Azteca andreae workers is a fatal error as 268 out of 276 potential cleptobionts (97.1 %) were captured in turn. The ant workers hunt in a group and use the "Velcro®" principle to cling firmly to the leaves of their host tree, permitting them to capture very large prey. Exceptions were one social wasp, plus some Trigona spp. workers and flies that landed directly on the prey and were able to take off immediately when attacked. We conclude that in this situation, previously captured prey attract potential cleptobionts that are captured in turn in most of the cases.

Social conformity and propagation of information in collective U-turns of fish schools.

Science.gov (United States)

Lecheval, Valentin; Jiang, Li; Tichit, Pierre; Sire, Clément; Hemelrijk, Charlotte K; Theraulaz, Guy

2018-04-25

Moving animal groups such as schools of fishes or flocks of birds often undergo sudden collective changes of their travelling direction as a consequence of stochastic fluctuations in heading of the individuals. However, the mechanisms by which these behavioural fluctuations arise at the individual level and propagate within a group are still unclear. In this study, we combine an experimental and theoretical approach to investigate spontaneous collective U-turns in groups of rummy-nose tetra ( Hemigrammus rhodostomus ) swimming in a ring-shaped tank. U-turns imply that fish switch their heading between the clockwise and anticlockwise direction. We reconstruct trajectories of individuals moving alone and in groups of different sizes. We show that the group decreases its swimming speed before a collective U-turn. This is in agreement with previous theoretical predictions showing that speed decrease facilitates an amplification of fluctuations in heading in the group, which can trigger U-turns. These collective U-turns are mostly initiated by individuals at the front of the group. Once an individual has initiated a U-turn, the new direction propagates through the group from front to back without amplification or dampening, resembling the dynamics of falling dominoes. The mean time between collective U-turns sharply increases as the size of the group increases. We develop an Ising spin model integrating anisotropic and asymmetrical interactions between fish and their tendency to follow the majority of their neighbours nonlinearly (social conformity). The model quantitatively reproduces key features of the dynamics and the frequency of collective U-turns observed in experiments. © 2018 The Author(s).

3D characterisation of tool wear whilst diamond turning silicon

OpenAIRE

Durazo-Cardenas, Isidro Sergio; Shore, Paul; Luo, X.; Jacklin, T.; Impey, S. A.; Cox, A.

2006-01-01

Nanometrically smooth infrared silicon optics can be manufactured by the diamond turning process. Due to its relatively low density, silicon is an ideal optical material for weight sensitive infrared (IR) applications. However, rapid diamond tool edge degradation and the effect on the achieved surface have prevented significant exploitation. With the aim of developing a process model to optimise the diamond turning of silicon optics, a series of experimental trials were devi...

Interferometric evaluation of diamond-turned mirrors for CO2 laser fusion

International Nuclear Information System (INIS)

Munroe, J.L.

1979-01-01

It is shown that single-point diamond-turned optics exhibit different characteristics than conventionally manufactured optics and the type of information required by the machinist is quite different than the information that would be required by an optician. It was also seen, with Antares being a good example, that single-point diamond turning allows the manufacture of geometries and scales that might be unthinkable if conventional manufacturing were to be used. As single-point diamond turning continues to improve in quality, machined optics will find application at shorter and shorter wavelengths. A whole new formalism to describe manufacturing errors in terms meaningful to the machinist will have to be developed

Efficiency analysis of the speed turns in the crawl stroke swimming.

Directory of Open Access Journals (Sweden)

Savchenko M.I.

2011-02-01

Full Text Available Contemporary approaches to improving technique of the speed in the crawl stroke swimming, namely roll-forward turn were considered in the paper. The performance efficiency is defined by the time covering 15 meter distance. The students of the sports mastering group aged 16-20 took part in the experiment. The video recordings of the Ukrainian, European and World Championships and Deflympic Games, and also chronometration during the department trainings served as the experimental data. The research showed that white improving the technical level of turns performance, the attention should be paid to the exact performance of all the elements of the turns.

The Lewisian turning point and international migration: the case of Japan.

Science.gov (United States)

Watanabe, S

1994-01-01

"This article critically examines the Lewisian turning point [concerning the availability of unlimited manpower resources] in light of Japan's experience since the mid-1800s. Japan reached its Lewisian turning point around 1960. Contrary to the assumptions of the theory however, the findings for Japan indicate that political factors have been more determinative of the rate of migration than purely economic ones. Prior to its turning point in 1960, international relations, war and forced repatriation were the decisive factors. Recently, though the inflow of foreign workers to fill labor shortages has increased, so also has the outflow of Japanese to accompany direct foreign investment." excerpt

grid will help physicists' global hunt for particles Researchers have begun running experiments with the MidWest Tier 2 Center, one of five regional computing centers in the US.

CERN Multimedia

Ames, Ben

2006-01-01

"When physicists at Switzerland's CERN laboratory turn on their newsest particle collider in 2007, they will rely on computer scientists in Chicago and Indianapolis to help sift through the results using a worldwide supercomputing grid." (1/2 page)

Strategy in Generative Planning of Turning Processes

NARCIS (Netherlands)

van Houten, Frederikus J.A.M.; Kals, H.J.J.

1986-01-01

This paper reports on the process and operations planning system ROUND and the strategies which underlie the decision making processes in the planning of turning operations. At first, an outline is given about the environment for which generative systems like ROUND are being developed. The

78 FR 79654 - Vermont: Proposed Authorization of State Hazardous Waste Management Program Revisions

Science.gov (United States)

2013-12-31

...] Vermont: Proposed Authorization of State Hazardous Waste Management Program Revisions AGENCY... Docket ID No. EPA-R01- RCRA-2013-0554, by mail to Sharon Leitch, RCRA Waste Management and UST Section..., RCRA Waste Management and UST Section, Office of Site Remediation and Restoration (OSRR07-1), US EPA...

Turning theory into practice: the development of modern transdermal drug delivery systems and future trends.

Science.gov (United States)

Perumal, O; Murthy, S N; Kalia, Y N

2013-01-01

Despite its remarkable barrier function, the skin remains an attractive site for systemic drug delivery given its easy accessibility, large surface area and the possibility to bypass the gastrointestinal tract and the liver and so modify drug absorption kinetics. The pioneering work of Scheuplein, Higuchi and others in the 1960s helped to explain the processes involved in passive percutaneous absorption and led to the development of mathematical models to describe transdermal drug delivery. The intervening years have seen these theories turned to practice and a significant number of transdermal systems are now available including some that employ active drug delivery. This review briefly discusses the evolution of transdermal therapeutic systems over the years and the potential of newer transdermal technologies to deliver hydrophilic drugs and macromolecules through the skin. © 2013 S. Karger AG, Basel.

Help with Hives

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Help With Hives KidsHealth / For Kids / Help With Hives What's in this article? What Are ... about what happened. The doctor can try to help figure out what might be causing your hives, ...

Negotiating behavioural change: therapists' proposal turns in Cognitive Behavioural Therapy.

Science.gov (United States)

Ekberg, Katie; Lecouteur, Amanda

2012-01-01

Cognitive behavioural therapy (CBT) is an internationally recognised method for treating depression. However, many of the techniques involved in CBT are accomplished within the therapy interaction in diverse ways, and with varying consequences for the trajectory of therapy session. This paper uses conversation analysis to examine some standard ways in which therapists propose suggestions for behavioural change to clients attending CBT sessions for depression in Australia. Therapists' proposal turns displayed their subordinate epistemic authority over the matter at hand, and emphasised a high degree of optionality on behalf of the client in accepting their suggestions. This practice was routinely accomplished via three standard proposal turns: (1) hedged recommendations; (2) interrogatives; and (3) information-giving. These proposal turns will be examined in relation to the negotiation of behavioural change, and the implications for CBT interactions between therapist and client will be discussed.

Bodies with noncircular cross sections and bank-to-turn missiles

Science.gov (United States)

Jackson, C. M., Jr.; Sawyer, W. C.

1992-01-01

A development status evaluation is presented for the aerodynamics of missile configurations with noncircular cross-sections and bank-to-turn maneuvering systems, giving attention to cases with elliptical and square cross-sections, as well as bodies with variable cross-sections. The assessment of bank-to-turn missile performance notes inherent stability/control problems. A summary and index are provided for aerodynamic data on monoplanar configurations, including those which incorporate airbreathing propulsion systems.

Learning, Teaching, and Turn Taking in the Repeated Assignment Game

OpenAIRE

Timothy N. Cason; Sau-Him Paul Lau; Vai-Lam Mui

2011-01-01

History-dependent strategies are often used to support cooperation in repeated game models. Using the indefinitely repeated common-pool resource assignment game and a perfect stranger experimental design, this paper reports novel evidence that players who have successfully used an efficiency-enhancing turn-taking strategy will teach other players in subsequent supergames to adopt this strategy. We find that subjects engage in turn taking frequently in both the Low Conflict and the High Confli...

Effect of transmitter turn-off time on transient soundings

Science.gov (United States)

Fitterman, D.V.; Anderson, W.L.

1987-01-01

A general procedure for computing the effect of non-zero turn-off time on the transient electromagnetic response is presented which can be applied to forward and inverse calculation methods for any transmitter-receiver configuration. We consider in detail the case of a large transmitter loop which has a receiver coil located at the center of the loop (central induction or in-loop array). For a linear turn-off ramp of width t0, the voltage response is shown to be the voltage due to an ideal step turn-off averaged over windows of width t0. Thus the effect is similar to that obtained by using averaging windows in the receiver. In general when time zero is taken to be the end of the ramp, the apparent resistivity increases for a homogeneous half-space over a limited time range. For time zero taken to be the start of the ramp the apparent resistivity is affected in the opposite direction. The effect of the ramp increases with increasing t0 and first-layer resistivity, is largest during the intermediate stage, and decreases with increasing time. It is shown that for a ramp turn-off, there is no effect in the early and late stages. For two-layered models with a resistive first layer (??1>??2), the apparent resistivity is increased in the intermediate stage. When the first layer is more conductive than the second layer (??1interpretation as shown by field examples; the influence is the greatest on near-surface layer parameters. ?? 1987.

Composting of tobacco plant waste by manual turning and forced aeration system

OpenAIRE

Nonglak Saithep

2009-01-01

The efficiency of tobacco plant waste composting, by the manual turning and the forced aeration system, was compared. Tobacco plant waste, cow manure, urea fertiliser, and a compost inoculum mixture at a 100:10:0.2:0.01 ratio respectively, with 60% (w/v) moisture content, were set up in piling forms. The piles of the manual turning system were provided with turning aeration by hand at intervals of 7 days during the composting process. For the forced aeration system, each pile was aerated by a...

Postcolonial turn : re-imagining anthropology and Africa

NARCIS (Netherlands)

Devisch, R.; Nyamnjoh, F.

2011-01-01

This book is a reflection on the mental decolonization of the postcolonialist turn in Africanist scholarship and is simultaneously a tribute to the late Professor Archibald Mafeje. A number of the articles, including the Introduction by A. Olukoshi and F. Nyamnjoh, are reprinted from the Codesria

Abolishment of Spontaneous Flight Turns in Visually Responsive Drosophila.

Science.gov (United States)

Ferris, Bennett Drew; Green, Jonathan; Maimon, Gaby

2018-01-22

Animals react rapidly to external stimuli, such as an approaching predator, but in other circumstances, they seem to act spontaneously, without any obvious external trigger. How do the neural processes mediating the execution of reflexive and spontaneous actions differ? We studied this question in tethered, flying Drosophila. We found that silencing a large but genetically defined set of non-motor neurons virtually eliminates spontaneous flight turns while preserving the tethered flies' ability to perform two types of visually evoked turns, demonstrating that, at least in flies, these two modes of action are almost completely dissociable. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of magneto rheological damper on tool vibration during hard turning

Science.gov (United States)

Paul, P. Sam; Varadarajan, A. S.

2012-12-01

Recently, the concept of hard turning has gained considerable attention in metal cutting as it can apparently replace the traditional process cycle of turning, heat treating, and finish grinding for assembly of hard wear resistant steel parts. The present investigation aims at developing a magneto rheological (MR) fluid damper for suppressing tool vibration and promoting better cutting performance during hard turning. The magneto rheological Fluid acts as a viscoelastic spring with non-linear vibration characteristics that are controlled by the composition of the magneto rheological fluid, the shape of the plunger and the electric parameters of the magnetizing field. Cutting experiments were conducted to arrive at a set of electrical, compositional and shape parameters that can suppress tool vibration and promote better cutting performance during turning of AISI 4340 steel of 46 HRC with minimal fluid application using hard metal insert with sculptured rake face. It was observed that the use of MR fluid damper reduces tool vibration and improves the cutting performance effectively. Also commercialization of this idea holds promise to the metal cutting industry.

Mass enhances speed but diminishes turn capacity in terrestrial pursuit predators

Science.gov (United States)

Wilson, Rory P; Griffiths, Iwan W; Mills, Michael GL; Carbone, Chris; Wilson, John W; Scantlebury, David M

2015-01-01

The dynamics of predator-prey pursuit appears complex, making the development of a framework explaining predator and prey strategies problematic. We develop a model for terrestrial, cursorial predators to examine how animal mass modulates predator and prey trajectories and affects best strategies for both parties. We incorporated the maximum speed-mass relationship with an explanation of why larger animals should have greater turn radii; the forces needed to turn scale linearly with mass whereas the maximum forces an animal can exert scale to a 2/3 power law. This clarifies why in a meta-analysis, we found a preponderance of predator/prey mass ratios that minimized the turn radii of predators compared to their prey. It also explained why acceleration data from wild cheetahs pursuing different prey showed different cornering behaviour with prey type. The outcome of predator prey pursuits thus depends critically on mass effects and the ability of animals to time turns precisely. DOI: http://dx.doi.org/10.7554/eLife.06487.001 PMID:26252515

Composting of tobacco plant waste by manual turning and forced aeration system

Directory of Open Access Journals (Sweden)

Nonglak Saithep

2009-05-01

Full Text Available The efficiency of tobacco plant waste composting, by the manual turning and the forced aeration system, was compared. Tobacco plant waste, cow manure, urea fertiliser, and a compost inoculum mixture at a 100:10:0.2:0.01 ratio respectively, with 60% (w/v moisture content, were set up in piling forms. The piles of the manual turning system were provided with turning aeration by hand at intervals of 7 days during the composting process. For the forced aeration system, each pile was aerated by a 3-HP air pump with a flow rate of 19 litres min-1 for 15 minutes every morning and evening. The completely randomised design of turned and force-aerated piles was performed in triplicate. The composting activity of both systems during the composting period was measured by several parameters: temperature, pH, moisture content, C/N ratio, growth of microorganisms, cellulase activity, and nicotine degradation in the set-up piles. Both systems had similar temperature, pH, and moisture content conditions in the piles during the composting process. However, the forced aeration system was more advantageous for the growth of mesophilic and thermophilic microorganisms, for cellulase activity from cellulase-producing microorganisms, and for nicotine degradation, when compared to the manual turning system. In conclusion, the forced aeration system was more efficient than the manual turning system in composting and is a viable alternative method for the composting process.

Experimentation and Prediction of Temperature Rise in Turning ...

African Journals Online (AJOL)

Experimentation and Prediction of Temperature Rise in Turning Process using Response Surface Methodology. ... Science, Technology and Arts Research Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue ...

The practical outfall of DOE compliance agreements

International Nuclear Information System (INIS)

Smith, Leanne; Henrie, Gregory O.

1992-01-01

Perhaps the significant regulatory issue facing the Department of Energy (DOE or the Department) is the compliant treatment, storage, and disposal of mixed (radioactive and hazardous) waste. Since DOE'S By-Product Rulemaking in 1987, when the Department acknowledged that the Resource Conservation and Recovery Act (RCRA) applied to the hazardous component of mixed waste, DOE has repeatedly communicated to the Environmental Protection Agency (EPA) and host States that, for mixed waste, DOE is not always able to strictly comply with RCRA standards and that bringing treatment on-line in an expeditious manner is proving very difficult. One of the most effective methods used between DOE and its regulators to address mixed waste management issues is the negotiation of compliance agreements. These agreements establish formal mile stones for bringing DOE sites into compliance. The milestones are not completed without overcoming technical roadblocks and a struggle for funding. However, agreements can establish technically attainable compliance methods that take into account the special problems radiation introduces into RCRA waste management. Compliance agreements help promote a cooperative relationship within the Department and between DOE and its regulators in that all parties have reached agreement and have a stake in attaining the same goal. Where agreements exist, mixed waste compliance efforts can proceed in a situation where all parties have a full understanding of each other's needs and expectations. (author)

A helping hand

NARCIS (Netherlands)

Mirjam de Klerk; Alice de Boer; Sjoerd Kooiker; Inger Plaisier; Peggy Schyns

2014-01-01

Original title: Hulp geboden   The help provided to people with a care need is about to undergo major changes in the Netherlands. People who need help will be expected to rely more on help from members of their network. What are the opportunities for informal carers and volunteers, and where

Spontaneous perseverative turning in rats with radiation-induced hippocampal damage

International Nuclear Information System (INIS)

Mickley, G.A.; Ferguson, J.L.; Nemeth, T.J.; Mulvihill, M.A.; Alderks, C.E.

1989-01-01

This study found a new behavioral correlate of lesions specific to the dentate granule cell layer of the hippocampus: spontaneous perseverative turning. Irradiation of a portion of the neonatal rat cerebral hemispheres produced hypoplasia of the granule cell layer of the hippocampal dentate gyrus while sparing the rest of the brain. Radiation-induced damage to the hippocampal formation caused rats placed in bowls to spontaneously turn in long, slow bouts without reversals. Irradiated subjects also exhibited other behaviors characteristic of hippocampal damage (e.g., perseveration in spontaneous exploration of the arms of a T-maze, retarded acquisition of a passive avoidance task, and increased horizontal locomotion). These data extend previously reported behavioral correlates of fascia dentata lesions and suggest the usefulness of a bout analysis of spontaneous bowl turning as a measure of nondiscrete-trial spontaneous alternation and a sensitive additional indicator of radiation-induced hippocampal damage

Travel Time Model for Right-Turning Vehicles of Secondary Street at Unsignalized Intersections

Directory of Open Access Journals (Sweden)

Feng Yu-Qin

2013-01-01

Full Text Available The travel time of right-turning vehicles on secondary street at unsignalized intersection is discussed in this paper. Under the assumption that the major-street through vehicles’ headway follows Erlang distribution and secondary-street right-turning vehicles’ headway follows Poisson distribution. The right-turning vehicles travel time model is established on the basis of gap theory and M/G/1 queue theory. Comparison is done with the common model based on the assumption that the major-street vehicles’ headway follows Poisson distribution. An intersection is selected to verify each model. The results show that the model established in this paper has stronger applicability, and its most relative error is less than 15%. In addition, the sensitivity analysis has been done. The results show that right-turning flow rate and major-street flow rate have a significant impact on the travel time. Hence, the methodology for travel time of right-turning vehicles at unsignalized intersection proposed in this paper is effective and applicable.

Measuring of roundness after turning of composite material with natural fibers

Directory of Open Access Journals (Sweden)

D. Mital

2016-12-01

Full Text Available The article is based on practical requirements from the reason of unequally removed material during the turning of the wood plastic composite (WPC. This results in geometrical deviations of the WPC bar diameter. WPC represents a relatively new group of materials that has been at the market for almost 30 years. In 1983 Lear Corporation in Wisconsine, USA made for the first time the interior panels of cars from composite materials – PP matrix with organic filler – 50 % wood flour. WPCs displace traditional materials such as wood, steel and cement materials in the marina industry. Designers are not limited technology of production from construction aspect, because different shapes and profiles can be produced by injection (resp. process of extrusion, but in the process of machining were monitored problems with tolerances. Mixed colors can be achieved by using of different pigments and one feels that this is real wood. Technologists begin to use convention technologies – drilling, milling and turning, as tendency of application of WPC increased. Knowledges about machining of WPC are not elaborate as deep as machining of metals or plastics. And this is a reason for orientation in this direction too. Commercial wood plastic composite MEGAWOOD (70 % wood flour, 30 % HDPE was a sample material in current investigation of roundness after turning of WPC. HSS EN ISO HS6-5-2 cutting tool was used. The geometry of the cutting tool was γ0 = 20°, α0 = 8°, κr = 45°, rε = 0,5 mm, εr = 90°. Cutting conditions during turning were as follows: cutting speed n = 900 m/min (constant, feed f = 0,1 to 0,61 mm, depth of cut ap = 0,5 mm for turning of final diameter d = 36 mm. It was dry turning. Roundness/cylindricity measuring system RA – 120 was used for measuring of roundness deviation. It was found that the roundness deviation increases with feed increasing. Popped heat was not used during the turning to final diameter – 36 mm. Using of popped heat

Turn-key SRF accelerators to drive subcritical reactors

International Nuclear Information System (INIS)

Johnson, Rolland P.

2011-01-01

Large particle accelerator projects, both accomplished and proposed, have been used to engage US industry through contracts and grants to develop efficient capabilities to design, develop, produce, and deliver entire accelerator systems or any needed subsystems. Staffed in many cases by experienced scientists and engineers from National Laboratories and Universities, existing companies could extend their portfolios to offer turn-key accelerators with parameters to match the needs of ADS. If the reactors were based on molten salt fuel such that trip rate requirements were relaxed, the developments needed for a multi-MW proton accelerator for ADS would be minimal. Turn-key SRF proton linacs for ADS operation can be ordered now to enable GW-level power generation from natural thorium, natural uranium, or nuclear waste from conventional reactors. (author)

Erratum to: Courses of helping alliance in the treatment of people with severe mental illness in Europe

DEFF Research Database (Denmark)

Loos, Sabine; Arnold, Katrin; Slade, Mike

2015-01-01

with severe mental illness across Europe over a measurement period of one year. METHODS: Self-ratings of the HA by 588 people with severe mental illness who participated in a multicentre European study (CEDAR; ISRCTN75841675) were examined using latent class analysis. RESULTS: Four main patterns of alliance...... of life. CONCLUSIONS: Results support findings from psychotherapy research about a predominantly stable course of the helping alliance in patients with severe mental illness over time. Implications for research and practice indicate to turn the attention to subgroups with noticeable courses.......PURPOSE: The helping alliance (HA) between patient and therapist has been studied in detail in psychotherapy research, but less is known about the HA in long-term community mental health care. The aim of this study was to identify typical courses of the HA and their predictors in a sample of people...

Helping for Change

Science.gov (United States)

Neuringer, Allen; Oleson, Kathryn C.

2010-01-01

In "Helping for Change," Allen Neuringer and Kathryn Oleson describe another strategy that individuals can use to achieve their green goals. You might ask, "How can helping someone else help me change when I'm in the habit of not fulfilling my own promises?" The authors answer that question by explaining how the social reinforcement in a helping…

Development of a Low Cost MQL Setup for Turning Operations

OpenAIRE

Islam Sumaiya; Khandoker Noman; Izham Mohamad; Azizi Tengku; Debnath Sujan

2017-01-01

In this study, the effect of MQL application on the tool wear, surface roughness and chip formation in turning Aluminum alloy 6061 is investigated. Experiments were carried out by plain turning of an Aluminum bar with varying depth of cut, cutting speeds (spindle speed) and cutting environments (Dry, Wet and MQL). A newly designed, cost efficient and portable MQL setup was developed for this study. For each experimental trial, five passes were carried out in order to promote the formation of ...

Heading Estimation of Robot Combine Harvesters during Turning Maneuveres.

Science.gov (United States)

Rahman, Md Mostafizar; Ishii, Kazunobu

2018-05-01

Absolute heading is an important parameter for a robot combine harvester or a robot tracked combine harvester, especially while it is turning, but due to the rapid turning of robot combine harvesters, its inertial measurement unit gives a gyro measurement bias that causes heading drift. Our research goal is to estimate the absolute heading of robot combine harvesters by compensating this gyro measurement bias during non-linear turning maneuvers. A sensor fusion method like the extended Kalman filter combined with the tracked combine harvester dynamic model and sensor measurements was used to estimate the absolute heading of a robot combine harvester. Circular, sinusoidal and concave shapes were used to evaluate the estimated heading produced by the sensor fusion method. The results indicate that the estimated heading is better than measured heading which was calculated from the integration of yaw rate gyro measurements, and the root mean square errors (RMSEs) for estimated headings are smaller than the measured headings. In practics, the target of this paper is thus the estimation of a heading or absolute heading that is bias compensated, and can be further used to calculate the exact crop periphery for automatic path planning of robot combine harvesters.

Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning

Directory of Open Access Journals (Sweden)

Tian-Syung Lan

2010-01-01

Full Text Available Surface roughness is often considered the main purpose in contemporary computer numerical controlled (CNC machining industry. Most existing optimization researches for CNC finish turning were either accomplished within certain manufacturing circumstances or achieved through numerous equipment operations. Therefore, a general deduction optimization scheme is deemed to be necessary for the industry. In this paper, the cutting depth, feed rate, speed, and tool nose runoff with low, medium, and high level are considered to optimize the surface roughness for finish turning based on L9(34 orthogonal array. Additionally, nine fuzzy control rules using triangle membership function with respective to five linguistic grades for surface roughness are constructed. Considering four input and twenty output intervals, the defuzzification using center of gravity is then completed. Thus, the optimum general fuzzy linguistic parameters can then be received. The confirmation experiment result showed that the surface roughness from the fuzzy linguistic optimization parameters is significantly advanced compared to that from the benchmark. This paper certainly proposes a general optimization scheme using orthogonal array fuzzy linguistic approach to the surface roughness for CNC turning with profound insight.

Spatial turn and animation practices inspired by cultural anthropology

Directory of Open Access Journals (Sweden)

Agnieszka Wieszaczewska

2016-09-01

Full Text Available Spatial turn is one of the cultural turns, which have recently occurred in the humanities. It stresses the importance of issues such as space and place and can be successfully used as a theoretical perspective gaining use in thought over issues such as globalisation, transnationality, mapping but also education. In the discourses of pedagogical science space and place are considered through their multidimensional impact on education and learning. As significant concepts rooting pedagogy or pedagogy of borderland. The pedagogical reflection on space could be also used in the field of animation practices, especially in activities, which are related to place somehow colonised.

Diamond-turning HP-21 beryllium to achieve an optical surface

International Nuclear Information System (INIS)

Allen, D.K.; Hauschildt, H.W.; Bryan, J.B.

1975-01-01

Investigation of diamond turning on beryllium was made in anticipation of obtaining an optical finish. Although results of past experiences were poor, it was decided to continue diamond turning on beryllium beyond initial failures. By changing speed and using coolant, partial success was achieved. Tool wear was the major problem. Tests were made to establish and plot wear as a function of cutting speed and time. Slower speeds did cause lower wear rates, but at no time did wear reach an acceptable level. The machine, tools, and procedure used were chosen based on the results of preliminary attempts and on previous experience. It was unnecessary to use an air-bearing spindle because tool failure governed the best finish that could be expected. All tools of diamond composition, whether single crystal or polycrystalline, wore at unacceptable rates. Based on present technology, it must be concluded that beryllium cannot be feasibly diamond turned to achieve an optical finish. (22 fig.)

Surface quality and topographic inspection of variable compliance part after precise turning

Science.gov (United States)

Nieslony, P.; Krolczyk, G. M.; Wojciechowski, S.; Chudy, R.; Zak, K.; Maruda, R. W.

2018-03-01

The paper presents the problem of precise turning of the mould parts with variable compliance and demonstrates a topographic inspection of the machined surface quality. The study was conducted for the cutting tools made of cemented carbide with coatings, in a range of variable cutting parameters. The long shaft with special axial hole, made of hardened 55NiCrMoV6 steel was selected as a workpiece. The carried out study included the stiffness measurement of the machining system, as well as the investigation of cutting force components. In this context, the surface topography parameters were evaluated using the stylus profile meter and analysed. The research revealed that the surface topography, alongside the 3D functional parameters, and PSD influences the performance of the machined surface. The lowest surface roughness parameters values, equalled to Sa = 1 μm and Sz = 4.3 μm have been obtained during turning with cutting speed vc = 90 m/min. The stable turning of variable compliance part affects the surface texture formation with a unidirectional perpendicular, anisotropic structure. Nevertheless, in case of unstable turning, the characteristic chatter marks are observed, and process dynamics has greater contribution in formation of surface finish than turning kinematics and elastic plastic deformation of workpiece.

Changes in inertia and effect on turning effort across different wheelchair configurations.

Science.gov (United States)

Caspall, Jayme J; Seligsohn, Erin; Dao, Phuc V; Sprigle, Stephen

2013-01-01

When executing turning maneuvers, manual wheelchair users must overcome the rotational inertia of the wheelchair system. Differences in wheelchair rotational inertia can result in increases in torque required to maneuver, resulting in greater propulsion effort and stress on the shoulder joints. The inertias of various configurations of an ultralightweight wheelchair were measured using a rotational inertia-measuring device. Adjustments in axle position, changes in wheel and tire type, and the addition of several accessories had various effects on rotational inertias. The configuration with the highest rotational inertia (solid tires, mag wheels with rearward axle) exceeded the configuration with the lowest (pneumatic tires, spoke wheels with forward axle) by 28%. The greater inertia requires increased torque to accelerate the wheelchair during turning. At a representative maximum acceleration, the reactive torque spanned the range of 11.7 to 15.0 N-m across the wheelchair configurations. At higher accelerations, these torques exceeded that required to overcome caster scrub during turning. These results indicate that a wheelchair's rotational inertia can significantly influence the torque required during turning and that this influence will affect active users who turn at higher speeds. Categorizing wheelchairs using both mass and rotational inertia would better represent differences in effort during wheelchair maneuvers.

Paying it forward: How helping others can reduce the psychological threat of receiving help

NARCIS (Netherlands)

Alvarez, K.; van Leeuwen, E.

2015-01-01

This paper shows that receiving help could be psychologically harmful for recipients, and passing on help to others after receiving help ("helping forward") is a good strategy to improve and restore help recipients' self-competence. Participants (N=87) received autonomy- or dependency-oriented help