Experiment and simulation of double-layered RC plates under impact loadings. Part 1: Impact tests for double-layered RC plates

International Nuclear Information System (INIS)

Shirai, T.; Ueda, M.; Taniguchi, H.; Kambayashi, A.; Ohno, T.; Ishikawa, N.

1993-01-01

At a nuclear power plant facility, it should be of interest and important problem to ensure structures against impact loads induced by projectile impacts or plant-internal accidents. It has been well known that local damage consists of spalling of concrete from the impacted area and scabbing of concrete from the back face of the target together with projectile penetration into the target. There are several techniques for improving the impact resistance of RC slabs, that is, lining with a steel plate on the impacted and/or rear face of the slab, making the slab a double-layered composite slab with an elastic absorber and employing a fiber reinforced concrete or a high-strength concrete as the slab materials. Of the many measures available for withstanding impact loads, the use of a double-layered reinforced concrete (RC) slab with absorber is expected to have the higher resistance in reducing or preventing local damage. This paper presents the results of an experimental investigation on the impact resistance of double-layered RC plates subjected to the impact of projectile. In the experiment, the effects of two parameters; the combination of two RC plates having different thicknesses and the existence of an absorber in the middle layer, are mainly investigated. And, the effects of the concrete thickness (7,9 and 11 cm) and the concrete strength (a normal-:35MPa, a lightweight-:40MPa and a high-strength:57MPa) of target were also examined. RC plates, 0.6m-square, were used for test specimens. The projectile has a mass of 0.43kg, made of steel with a flat nose. An average projectile velocity was about 170m/sec. A rubber plate shaped into a square with the same size of RC plate was used for a double-layered specimen as an absorber which was put between two RC plates. It could be concluded that double-layering and presence of an absorber had a considerable effect on the increase of impact resistance of RC plate. In order to reduce local damage, it is more effective to

Theory-Based Analysis of Interest in an HIV Vaccine for Reasons Indicative of Risk Compensation Among African American Women.

Science.gov (United States)

Painter, Julia E; Temple, Brandie S; Woods, Laura A; Cwiak, Carrie; Haddad, Lisa B; Mulligan, Mark J; DiClemente, Ralph J

2018-06-01

Licensure of an HIV vaccine could reduce or eliminate HIV among vulnerable populations. However, vaccine effectiveness could be undermined by risk compensation (RC), defined by an increase in risky behavior due to a belief that the vaccine will confer protection. Interest in an HIV vaccine for reasons indicative of RC may serve as an indicator of actual RC in a postlicensure era. This study assessed factors associated with interest in an HIV vaccine for reasons indicative of RC among African American women aged 18 to 55 years, recruited from a hospital-based family planning clinic in Atlanta, Georgia ( N = 321). Data were collected using audio-computer-assisted surveys. Survey items were guided by risk homeostasis theory and social cognitive theory. Multivariable logistic regression was used to assess determinants of interest in an HIV vaccine for reasons indicative of RC. Thirty-eight percent of the sample expressed interest in an HIV vaccine for at least one reason indicative of RC. In the final model, interest in an HIV vaccine for reasons indicative of RC was positively associated with higher impulsivity, perceived benefits of sexual risk behaviors, and perceived benefits of HIV vaccination; it was negatively associated with having at least some college education, positive future orientation, and self-efficacy for sex refusal. Results suggest that demographic, personality, and theory-based psychosocial factors are salient to wanting an HIV vaccine for reasons indicative of RC, and underscore the need for risk-reduction counseling alongside vaccination during the eventual rollout of an HIV vaccine.

The Birth of a Black Rice Gene and Its Local Spread by Introgression.

Science.gov (United States)

Oikawa, Tetsuo; Maeda, Hiroaki; Oguchi, Taichi; Yamaguchi, Takuya; Tanabe, Noriko; Ebana, Kaworu; Yano, Masahiro; Ebitani, Takeshi; Izawa, Takeshi

2015-09-01

The origin and spread of novel agronomic traits during crop domestication are complex events in plant evolution. Wild rice (Oryza rufipogon) has red grains due to the accumulation of proanthocyanidins, whereas most cultivated rice (Oryza sativa) varieties have white grains induced by a defective allele in the Rc basic helix-loop-helix (bHLH) gene. Although the events surrounding the origin and spread of black rice traits remain unknown, varieties with black grains due to anthocyanin accumulation are distributed in various locations throughout Asia. Here, we show that the black grain trait originated from ectopic expression of the Kala4 bHLH gene due to rearrangement in the promoter region. Both the Rc and Kala4 genes activate upstream flavonol biosynthesis genes, such as chalcone synthase and dihydroflavonol-4-reductase, and downstream genes, such as leucoanthocyanidin reductase and leucoanthocyanidin dioxygenase, to produce the respective specific pigments. Genome analysis of 21 black rice varieties as well as red- and white-grained landraces demonstrated that black rice arose in tropical japonica and its subsequent spread to the indica subspecies can be attributed to the causal alleles of Kala4. The relatively small size of genomic fragments of tropical japonica origin in some indica varieties indicates that refined introgression must have occurred by natural crossbreeding in the course of evolution of the black trait in rice. © 2015 American Society of Plant Biologists. All rights reserved.

Performance of RC columns with partial length corrosion

International Nuclear Information System (INIS)

Wang Xiaohui; Liang Fayun

2008-01-01

Experimental and analytical studies on the load capacity of reinforced concrete (RC) columns with partial length corrosion are presented, where only a fraction of the column length was corroded. Twelve simply supported columns were eccentrically loaded. The primary variables were partial length corrosion in tensile or compressive zone and the corrosion level within this length. The failure of the corroded column occurs in the partial length, mainly developed from or located nearby or merged with the longitudinal corrosion cracks. For RC column with large eccentricity, load capacity of the column is mainly influenced by the partial length corrosion in tensile zone; while for RC column with small eccentricity, load capacity of the column greatly decreases due to the partial length corrosion in compressive zone. The destruction of the longitudinally mechanical integrality of the column in the partial length leads to this great reduction of the load capacity of the RC column

Analysis and optimization of RC delay in vertical nanoplate FET

Science.gov (United States)

Woo, Changbeom; Ko, Kyul; Kim, Jongsu; Kim, Minsoo; Kang, Myounggon; Shin, Hyungcheol

2017-10-01

In this paper, we have analyzed short channel effects (SCEs) and RC delay with Vertical nanoplate FET (VNFET) using 3-D Technology computer-aided design (TCAD) simulation. The device is based on International Technology Road-map for Semiconductor (ITRS) 2013 recommendations, and it has initially gate length (LG) of 12.2 nm, channel thickness (Tch) of 4 nm, and spacer length (LSD) of 6 nm. To obtain improved performance by reducing RC delay, each dimension is adjusted (LG = 12.2 nm, Tch = 6 nm, LSD = 11.9 nm). It has each characteristic in this dimension (Ion/Ioff = 1.64 × 105, Subthreshold swing (S.S.) = 73 mV/dec, Drain-induced barrier lowering (DIBL) = 60 mV/V, and RC delay = 0.214 ps). Furthermore, with long shallow trench isolation (STI) length and thick insulator thickness (Ti), we can reduce RC delay from 0.214 ps to 0.163 ps. It is about a 23.8% reduction. Without decreasing drain current, there is a reduction of RC delay as reducing outer fringing capacitance (Cof). Finally, when source/drain spacer length is set to be different, we have verified RC delay to be optimum.

New PN Even Balanced Sequences for Spread-Spectrum Systems

Directory of Open Access Journals (Sweden)

Inácio JAL

2005-01-01

Full Text Available A new class of pseudonoise even balanced (PN-EB binary spreading sequences is derived from existing classical odd-length families of maximum-length sequences, such as those proposed by Gold, by appending or inserting one extra-zero element (chip to the original sequences. The incentive to generate large families of PN-EB spreading sequences is motivated by analyzing the spreading effect of these sequences from a natural sampling point of view. From this analysis a new definition for PG is established, from which it becomes clear that very high processing gains (PGs can be achieved in band-limited direct-sequence spread-spectrum (DSSS applications by using spreading sequences with zero mean, given that certain conditions regarding spectral aliasing are met. To obtain large families of even balanced (i.e., equal number of ones and zeros sequences, two design criteria are proposed, namely the ranging criterion (RC and the generating ranging criterion (GRC. PN-EB sequences in the polynomial range are derived using these criteria, and it is shown that they exhibit secondary autocorrelation and cross-correlation peaks comparable to the sequences they are derived from. The methods proposed not only facilitate the generation of large numbers of new PN-EB spreading sequences required for CDMA applications, but simultaneously offer high processing gains and good despreading characteristics in multiuser SS scenarios with band-limited noise and interference spectra. Simulation results are presented to confirm the respective claims made.

Executive Compensation and the Cost of Debt

NARCIS (Netherlands)

Kabir, Rezaul; Liu, Hao; Veld-Merkoulova, Yulia V.

2013-01-01

This study examines how different components of executive compensation affect the cost of debt. We find that debt-like and equity-like pay components have differing effects: an increase in defined benefit pensions is associated with lower bond yield spread, while higher share holdings lead to higher

An under-designed RC frame: Seismic assessment through displacement based approach and possible refurbishment with FRP strips and RC jacketing

Science.gov (United States)

Valente, Marco; Milani, Gabriele

2017-07-01

Many existing reinforced concrete buildings in Southern Europe were built (and hence designed) before the introduction of displacement based design in national seismic codes. They are obviously highly vulnerable to seismic actions. In such a situation, simplified methodologies for the seismic assessment and retrofitting of existing structures are required. In this study, a displacement based procedure using non-linear static analyses is applied to a four-story existing RC frame. The aim is to obtain an estimation of its overall structural inadequacy as well as the effectiveness of a specific retrofitting intervention by means of GFRP laminates and RC jacketing. Accurate numerical models are developed within a displacement based approach to reproduce the seismic response of the RC frame in the original configuration and after strengthening.

The Second ICASE/LaRC Industry Roundtable: Session Proceedings

Science.gov (United States)

Girimaji, Sharath

1997-01-01

The second ICASE/LaRC Industry Roundtable was held October 7-9, 1996 at the Williamsburg Hospitality House, Williamsburg, Virginia. Like the first roundtable in 1994, this meeting had two objectives: (1) to expose ICASE and LaRC scientists to industrial research agendas; and (2) to acquaint industry with the capabilities and technology available at ICASE, LaRC and academic partners of ICASE. Nineteen sessions were held in three parallel tracks. Of the 170 participants, over one third were affiliated with various industries. Proceedings from the different sessions are summarized in this report.

An enhanced chaotic key-based RC5 block cipher adapted to image encryption

Science.gov (United States)

Faragallah, Osama S.

2012-07-01

RC5 is a block cipher that has several salient features such as adaptability to process different word lengths with a variable block size, a variable number of rounds and a variable-length secret key. However, RC5 can be broken with various attacks such as correlation attack, timing attack, known plaintext correlation attack and differential attacks, revealing weak security. We aimed to enhance the RC5 block cipher to be more secure and efficient for real-time applications while preserving its advantages. For this purpose, this article introduces a new approach based on strengthening both the confusion and diffusion operations by combining chaos and cryptographic primitive operations to produce round keys with better pseudo-random sequences. Comparative security analysis and performance evaluation of the enhanced RC5 block cipher (ERC5) with RC5, RC6 and chaotic block cipher algorithm (CBCA) are addressed. Several test images are used for inspecting the validity of the encryption and decryption algorithms. The experimental results show the superiority of the suggested enhanced RC5 (ERC5) block cipher to image encryption algorithms such as RC5, RC6 and CBCA from the security analysis and performance evaluation points of view.

Executive Compensation and the Cost of Debt

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Li, Hao; Veld-Merkoulova, Yulia V.

2010-01-01

We examine how executive compensation affects the cost of debt financing. Analyzing CEO pay data from the UK, we find that debt-like and equity-like pay components have opposite effects on the cost of debt. An increase in defined benefit pensions is associated with lower bond yield spread, while an

Design of RC frames for pre-selected collapse mechanism and ...

Indian Academy of Sciences (India)

In this study, total energy of RC frames is calculated and .... curvature relations of RC beam and column members are required for both ..... Case study ..... Turkish Seismic Design Code 2007 Ministry of Public Works and Settlement, Ankara.

The role of relational capital (RC in green supply chain management (GSCM

Directory of Open Access Journals (Sweden)

Claudia Viviane Viegas

2015-09-01

Full Text Available Green Supply Chain Management (GSCM is an emergent issue in operations management. It is addressed to intra and inter-organizational practices adoption in order to promote sustainability in supply chains. Relational Capital (RC, also an emergent issue, plays a relevant role to resize views based solely in transactions costs and resources to a relationship view leaned on governance for information, trust and longevity in relationships, looking for positive results for all the chain’s participants. This article reviews and criticizes seminal literature on intangible assets in order to rescue RC features and link them to GSCM development. Through exploratory and descriptive methods, recent studies on RC and GSCM are identified with respect their descriptors – ways in which RC is understood and employed in GSCM; focus – goals and main use of RC; and directionality – if developments of RC in GSCM are addressed from producers to their suppliers and respective clients, or if suppliers and clients also address results of RC. It is concluded that, usually, there is unidirectionality in the application of such efforts: improvement initiatives go from the producer to the supplier or client development, but processes through which environmental practices of suppliers and clients influence the performance of GSCM are poor explored.

Compensation of the open-quotes Pacmanclose quotes tune spread by tailoring the beam current

International Nuclear Information System (INIS)

Furman, M.A.

1995-04-01

' Factory'-like e + -e - colliders presently under design or construction achieve high luminosity by resorting to large numbers of closely-spaced bunches. The short bunch spacing implies that there are unavoidable parasitic collisions (PCs) in the neighborhood of the interaction point (IP). Since the bunch population of the beam is not uniform due to an intentional ion-clearing gap, the bunches at the head or tail of the train (open-quotes pacman bunchesclose quotes) experience different beam-beam tune shifts than those away from the edges (open-quotes typical bunchesclose quotes). The author presents here a method to minimize the vertical tune spread at the expense of increasing the horizontal tune spread (it is assumed that there is only one IP). Since the beam-beam dynamics for flat beams typically tolerates a significantly higher horizontal tune spread than a vertical tune spread, this method implies a net advantage. The author presents this discussion in the context of the PEP-II collider

Advanced field-solver techniques for RC extraction of integrated circuits

CERN Document Server

Yu, Wenjian

2014-01-01

Resistance and capacitance (RC) extraction is an essential step in modeling the interconnection wires and substrate coupling effect in nanometer-technology integrated circuits (IC). The field-solver techniques for RC extraction guarantee the accuracy of modeling, and are becoming increasingly important in meeting the demand for accurate modeling and simulation of VLSI designs. Advanced Field-Solver Techniques for RC Extraction of Integrated Circuits presents a systematic introduction to, and treatment of, the key field-solver methods for RC extraction of VLSI interconnects and substrate coupling in mixed-signal ICs. Various field-solver techniques are explained in detail, with real-world examples to illustrate the advantages and disadvantages of each algorithm. This book will benefit graduate students and researchers in the field of electrical and computer engineering, as well as engineers working in the IC design and design automation industries. Dr. Wenjian Yu is an Associate Professor at the Department of ...

A third-order class-D amplifier with and without ripple compensation

Science.gov (United States)

Cox, Stephen M.; du Toit Mouton, H.

2018-06-01

We analyse the nonlinear behaviour of a third-order class-D amplifier, and demonstrate the remarkable effectiveness of the recently introduced ripple compensation (RC) technique in reducing the audio distortion of the device. The amplifier converts an input audio signal to a high-frequency train of rectangular pulses, whose widths are modulated according to the input signal (pulse-width modulation) and employs negative feedback. After determining the steady-state operating point for constant input and calculating its stability, we derive a small-signal model (SSM), which yields in closed form the transfer function relating (infinitesimal) input and output disturbances. This SSM shows how the RC technique is able to linearise the small-signal response of the device. We extend this SSM through a fully nonlinear perturbation calculation of the dynamics of the amplifier, based on the disparity in time scales between the pulse train and the audio signal. We obtain the nonlinear response of the amplifier to a general audio signal, avoiding the linearisation inherent in the SSM; we thereby more precisely quantify the reduction in distortion achieved through RC. Finally, simulations corroborate our theoretical predictions and illustrate the dramatic deterioration in performance that occurs when the amplifier is operated in an unstable regime. The perturbation calculation is rather general, and may be adapted to quantify the way in which other nonlinear negative-feedback pulse-modulated devices track a time-varying input signal that slowly modulates the system parameters.

Stochastic Wheel-Slip Compensation Based Robot Localization and Mapping

Directory of Open Access Journals (Sweden)

SIDHARTHAN, R. K.

2016-05-01

Full Text Available Wheel slip compensation is vital for building accurate and reliable dead reckoning based robot localization and mapping algorithms. This investigation presents stochastic slip compensation scheme for robot localization and mapping. Main idea of the slip compensation technique is to use wheel-slip data obtained from experiments to model the variations in slip velocity as Gaussian distributions. This leads to a family of models that are switched depending on the input command. To obtain the wheel-slip measurements, experiments are conducted on a wheeled mobile robot and the measurements thus obtained are used to build the Gaussian models. Then the localization and mapping algorithm is tested on an experimental terrain and a new metric called the map spread factor is used to evaluate the ability of the slip compensation technique. Our results clearly indicate that the proposed methodology improves the accuracy by 72.55% for rotation and 66.67% for translation motion as against an uncompensated mapping system. The proposed compensation technique eliminates the need for extro receptive sensors for slip compensation, complex feature extraction and association algorithms. As a result, we obtain a simple slip compensation scheme for localization and mapping.

An optimum design of R-C oscillatory De-Qing circuit

International Nuclear Information System (INIS)

Cao Dezhang; Pan Linghe; Yang Tianlu

1990-01-01

An optimum design of R-C oscillatory De-Qing circuit has been developed for voltage regulation of the pulse modulator. When a new coefficient T 3 /T is introduced, the selection of De-Qing circuit parameters will become quite simple and the optimum parameters can be calculated directly. The De-Qing circuit parameters calculated will be effective in the whole range of the percentage regulation η from zero to maximum design value. The limit value of η is 0.36 or 0.29, theoretically, when the time constant of the De-Qing circuit is 3RC or 5RC respectively

Observation of damage process in RC beams under cucle bending by acoustic emission

International Nuclear Information System (INIS)

Shigeishi, Mitsuhiro; Ohtsu, Masayasu; Tsuji, Nobuyuki; Yasuoka, Daisuke

1997-01-01

Reinforced concrete (RC) structures are generally applied to construction of buildings and bridges, and are imposed on cyclic loading incessantly. It is considered that detected acoustic emission (AE) waveforms are associated with the damage degree and the fracture mechanisms of RC structures. Therefor, the cyclic bending tests are applied to damaged RC beam specimens. To evaluate the interior of the damaged RC beams, the AE source kinematics are determined by 'SiGMA' procedure for AE moment tensor analysis. By using 'SiGMA' procedure, AE source kinematics, such as source locations, crack types, crack orientations and crack motions, can be identified. The results show the applicability to observation of the fracture process under cyclic bending load and evaluation the degree of damage of RC beam.

Multi-level nonlinear modeling verification scheme of RC high-rise wall buildings

OpenAIRE

Alwaeli, W.; Mwafy, A.; Pilakoutas, K.; Guadagnini, M.

2017-01-01

Earthquake-resistant reinforced concrete (RC) high-rise wall buildings are designed and detailed to respond well beyond the elastic range under the expected earthquake ground motions. However, despite their considerable section depth, in terms of analysis, RC walls are still often treated as linear elements, ignoring the effect of deformation compatibility. Due to the limited number of available comprehensive experimental studies on RC structural wall systems subjected to cycling loading, few...

R$_{b}$ - R$_{c}$ crisis and new physics

CERN Document Server

Bhattacharya, G; Hou Wei Shu; Bhattacharyya, Gautam; Branco, Gustavo C; Hou, Wei Shu

1996-01-01

The experimental values of R_b and R_c are the only data which do not seem to agree with Standard Model predictions. Although it is still premature to draw any definite conclusions, it is timely to look for new physics which could explain the excess in R_b and deficit in R_c. We investigate this problem in a simple extension of the Standard Model, where a charge +2/3 isosinglet quark is added to the standard spectrum. Upon the further introduction of an extra scalar doublet, one finds a solution with interesting consequences.

Research on the Fatigue Flexural Performance of RC Beams Attacked by Salt Spray

Science.gov (United States)

Mao, Jiang-hong; Xu, Fang-yuan; Jin, Wei-liang; Zhang, Jun; Wu, Xi-xi; Chen, Cai-sheng

2018-04-01

The fatigue flexural performance of RC beams attacked by salt spray was studied. A testing method involving electro osmosis, electrical accelerated corrosion and salt spray was proposed. This corrosion process method effectively simulates real-world salt spray and fatigue loading exerted by RC components on sea bridges. Four RC beams that have different stress amplitudes were tested. It is found that deterioration by corrosion and fatigue loading reduces the fatigue life of the RC and decreases the ability of deformation. The fatigue life and deflection ability could be reduced by increasing the stress amplitude and the corrosion duration time. The test result demonstrates that this experimental method can couple corrosion deterioration and fatigue loading reasonably. This procedure may be applied to evaluate the fatigue life and concrete durability of RC components located in a natural salt spray environment.

The RC Circuit: An Approach with Fourier Transforms In this article ...

Indian Academy of Sciences (India)

CLASSROOM. Mitrajyoti Ghosh. 83, Mitrapara 2nd Lane, Harinavi,. Kolkata 700148, West Bengal,. India. Email: mijospeakingnow@gmail.com. The RC Circuit: An Approach with Fourier Transforms. In this article we shall mathematically analyse the Resistor-. Capacitor (RC) circuit with the help of Fourier transforms. (FT).

Ultimate capacity and influenced factors analysis of nuclear RC containment subjected to internal pressure

International Nuclear Information System (INIS)

Song Chenning; Hou Gangling; Zhou Guoliang

2014-01-01

Ultimate compressive bearing capacity, influenced factors and its rules of nuclear RC containment are key problems of safety assessment, accident treatment and structure design, etc. Ultimate compressive bearing capacity of nuclear RC containment is shown by concrete damaged plasticity model and steel double liner model of ABAQUS. The study shows that the concrete of nuclear RC containment cylinder wall becomes plastic when the internal pressure is up to 0.87 MPa, the maximum tensile strain of steel liner exceeds 3000 × 10 6 and nuclear RC containment reaches ultimate status when the internal pressure is up to 1.02 MPa. The result shows that nuclear RC containment is in elastic condition under the design internal pressure and the bearing capacity meets requirement. Prestress and steel liner play key parts in the ultimate internal pressure and failure mode of nuclear RC containment. The study results have value for the analysis of ultimate compressive bearing capacity, structure design and safety assessment. (authors)

75 FR 1356 - RC2 Corporation, Provisional Acceptance of a Settlement Agreement and Order

Science.gov (United States)

2010-01-11

... primarily at toy stores and various retailers nationwide, and secondarily through RC2's e-commerce websites... various retailers nationwide, and secondarily through RC2's e-commerce Web sites or as `sub-components' of...(e). Published below is a provisionally-accepted Settlement Agreement with RC2 Corporation...

Limit analysis on FRP-strengthened RC members

Directory of Open Access Journals (Sweden)

D. De Domenico

2014-07-01

Full Text Available Reinforced concrete (RC members strengthened with externally bonded fiber-reinforced-polymer (FRP plates are numerically investigated by a plasticity-based limit analysis approach. The key-concept of the present approach is to adopt proper constitutive models for concrete, steel reinforcement bars (re-bars and FRP strengthening plates according to a multi-yield-criteria formulation. This allows the prediction of concrete crushing, steel bars yielding and FRP rupture that may occur at the ultimate limit state. To simulate such limitstate of the analysed elements, two iterative methods performing linear elastic analyses with adaptive elastic parameters and finite elements (FEs description are employed. The peak loads and collapse mechanisms predicted for FRP-plated RC beams are validated by comparison with the corresponding experimental findings.

Out-of-plane ultimate shear strength of RC mat-slab foundations

International Nuclear Information System (INIS)

Kumagai, Hitoshi; Nukui, Yasushi; Imamura, Akira; Terayama, Takeshi; Hagiwara, Tetsuya; Kojima, Isao

2011-01-01

There have been few studies on the out-of-plane shear in RC mat-slab foundations, and the reasonable method has been demanded to estimate ultimate shear strength of RC mat-slab foundations in the nuclear facilities. In the previous study, the out-of-plane loading tests on the 20 square slab specimens had been performed to collect the fundamental data. In this study, the test results were successfully predicted by 3D non-linear Finite Element Analysis. It has been confirmed that the ultimate shear stress in the slab specimen can be estimated by the Arakawa's formula, which is commonly used to estimate the shear strength of RC beams. (author)

MASH Test 3-11 on the T131RC Bridge Rail

Science.gov (United States)

2012-10-01

Texas Department of Transportation (TxDOT) currently uses the TxDOT Type T101RC Bridge Rail, : a steel post and beam bridge rail anchored to the top of concrete curbs. The T101RC Bridge Rail is : 27 inches in height and can be anchored to the top of ...

Noise analysis of gate electrode work function engineered recessed channel (GEWE-RC) MOSFET

International Nuclear Information System (INIS)

Agarwala, Ajita; Chaujar, Rishu

2012-01-01

This paper discusses the noise assessment, using ATLAS device simulation software, of a gate electrode work function engineered recessed channel (GEWE-RC) MOSFET involving an RC and GEWE design integrated onto a conventional MOSFET. Furthermore, the behaviour of GEWE-RC MOSFET is compared with that of a conventional MOSFET having the same device parameters. This paper thus optimizes and predicts the feasibility of a novel design, i.e., GEWE-RC MOSFET for high-performance applications where device and noise reduction is a major concern. The noise metrics taken into consideration are: minimum noise figure and optimum source impedance. The statistical tools auto correlation and cross correlation are also analysed owing to the random nature of noise.

Evaluation of reuterin production in urogenital probiotic Lactobacillus reuteri RC-14.

Science.gov (United States)

Cadieux, Peter; Wind, Anette; Sommer, Philip; Schaefer, Laura; Crowley, Kate; Britton, Robert A; Reid, Gregor

2008-08-01

Classified as a distinct species in 1980, Lactobacillus reuteri strains have been used in probiotic formulations for intestinal and urogenital applications. In the former, the primary mechanism of action of L. reuteri SD2112 (ATCC 55730) has been purported to be its ability to produce the antibiotic 3-hydroxypropionaldehyde (3-HPA), also known as reuterin. In the vagina, it has been postulated that probiotic Lactobacillus reuteri RC-14 does not require reuterin production but mediates a restoration of the normal microbiota via hydrogen peroxide, biosurfactant, lactic acid production, and immune modulation. The aim of the present study was to determine whether strain RC-14 produced reuterin. Using PCR and DNA dot blot analyses, numerous Lactobacillus species, including RC-14, were screened for the presence of the gene encoding the large subunit of glycerol dehydratase (gldC), the enzyme responsible for reuterin production. In addition, lactobacilli were grown in glycerol-based media and both high-performance liquid chromatography and a colorimetric assay were used to test for the presence of reuterin. L. reuteri RC-14 was determined to be negative for gldC sequences, as well as for the production of reuterin when cultured in the presence of glycerol. These findings support that the probiotic effects of L. reuteri RC-14, repeatedly demonstrated during numerous studies of the intestine and vagina, are independent of reuterin production.

Study on labelling methods of 125I-RC-160 and its biodistribution in animals

International Nuclear Information System (INIS)

Wang Jing; Wang Xiqing; Wang Liangang; Li Fujun; Deng Jinglan

2002-01-01

A method for the iodination of peptide RC-160 with high efficiency was developed. RC-160 was iodinated with N-bromosuccinimide (NBS) as oxidant, the conventional chloramine T (Ch-T) method was used as control. The labelling condition of NBS method was optimized and radiolabelled conjugate 125 I-RC-160 was assessed as follows: no further purification was needed, the measured labelling yield of 125 I-RC-160 was 92% and the specific activity was 1.95 x 10 12 Bq/m mol. The yield increased as the amount of NBS increased. The optimal ratio of RC-160 (μg): 125 I (MBq): NBS(μg) was 3:7.4:1. For Ch-T method, the labelling yield is 56% and specific activity was 0.65 x 10 12 Bq/m mol; but after purification by SepPak-C 18 , the labelling yield may reach as high as 92%. 1h after injection, radioactivity in blood decreased by 87.2%. No obvious concentration of 125 I-RC-160 in thyroid or kidney was observed

Minimum beam-energy spread of a high-current rf linac

International Nuclear Information System (INIS)

Chan, K.C.D.; Fraser, J.S.

1987-01-01

Energy spread is an important parameter of an electron linac and, usually, is determined by the time dependence of the external rf accelerating field. By using a combination of fundamental and higher harmonic frequencies, the accelerating field can be maintained approximately constant over a beam bunch with the resultant energy spread approximately zero. This technique is no longer adequate when the longitudinal wake field of the beam bunch is taken into account. The wake-field variation along the bunch length introduces an energy spread that cannot be exactly compensated for with the use of fundamental and higher harmonic frequencies. The achievable minimum energy spread including the wake-field effect is therefore limited. In this paper, we report the minimum energy spreads achievable using the fundamental and third-harmonic frequencies, calculated using a least-squares algorithm, for some typical structures in use at Los Alamos National Laboratory. The dependence of these results on bunch shape, bunch charge, and structure frequency is discussed. Also included are discussions of schemes for implementing the third-harmonic frequency and their effectiveness

Two frequency beam-loading compensation in the drive-beam accelerator of the CLIC Test Facility

CERN Document Server

Braun, Hans Heinrich

1999-01-01

The CLIC Test Facility (CTF) is a prototype two-beam accelerator, in which a high-current "drive beam" is used to generate the RF power for the main-beam accelerator. The drive-beam accelerator consists of two S-band structures which accelerate a bunch train with a total charge of 500 nC. The substantial beam loading is compensated by operating the two accelerating structures at 7.81 MHz above and below the bunch repetition frequency, respectively. This introduces a change of RF phase from bunch to bunch, which leads, together with off-crest injection into the accelerator, to an approximate compensation of the beam loading. Due to the sinusoidal time-dependency of the RF field, an energy spread of about 7% remains in the bunch train. A set of idler cavities has been installed to reduce this residual energy spread further. In this paper, the considerations that motivated the choice of the parameters of the beam-loading compensation system, together with the experimental results, are presented.

RC Circuits: Some Computer-Interfaced Experiments.

Science.gov (United States)

Jolly, Pratibha; Verma, Mallika

1994-01-01

Describes a simple computer-interface experiment for recording the response of an RC network to an arbitrary input excitation. The setup is used to pose a variety of open-ended investigations in network modeling by varying the initial conditions, input signal waveform, and the circuit topology. (DDR)

Strut and tie modeling for RC short beams with corroded stirrups

Directory of Open Access Journals (Sweden)

Ahmed K. El-Sayed

Full Text Available Corrosion of steel reinforcement is one of the major problems that shorten the service life of reinforced concrete (RC structures. Steel stirrups, due to their location as an outer reinforcement, are more susceptible to corrosion problems and damage. However, there is limited research work in the literature on the effects of stirrup corrosion on the shear strength of RC beams. This paper attempts to evaluate analytically the residual shear strength of RC short beams with corrosion-damaged stirrups. The shear strength of short or deep beams are generally determined using the strut and tie model. The corrosion effects were implemented in the model to make it capable of predicting the residual shear capacity of RC beams with corroded stirrups. The effect of corrosion is implemented considering the reduction in geometry of the concrete cross section due to spalling and reduction in effective compressive strength of concrete due to corrosion cracks. The proposed strut and tie model which accounts for the corrosion effects was verified using the experimental data available in the literature, and good agreement was found.

Numerical study on shear resisting mechanism for corroded RC box culverts

International Nuclear Information System (INIS)

Matsuo, Toyofumi; Matsumura, Takuro; Iwamori, Akiyuki

2013-01-01

This paper discusses the effects of reinforcing steel corrosion on the shear resisting mechanism of RC box culverts and the applicability of the material degradation model in a finite element method. First, in FEM analyses, loss of reinforcement section area and initial tension strain due to reinforcement corrosion, and deteriorated bond characteristics between reinforcement and concrete, were considered. Second, cyclic loading tests using full-scale corroded specimens were numerically analyzed. The analyzed crack patterns and load-displacement relationships up to the maximum load were observed to be in close agreement with the experiment results within the average corrosion ratio of 10% of primary reinforcement. The fact that corrosion cracks can importantly affect the progression of shear cracks and shear strength of RC beams was also found. On the other hand, we established that RC box culverts being statically indeterminate structures, sectional forces are redistributed after cracking damage, and local material deterioration has a minor effect on shear capacity. Furthermore, a parametric study was carried out for corroded RC box culverts using parameters such as size, steel corrosion location, and corrosion level. (author)

Fractional RC and LC Electrical Circuits

Directory of Open Access Journals (Sweden)

Gómez-Aguilar José Francisco

2014-04-01

Full Text Available In this paper we propose a fractional differential equation for the electrical RC and LC circuit in terms of the fractional time derivatives of the Caputo type. The order of the derivative being considered is 0 < ɣ ≤1. To keep the dimensionality of the physical parameters R, L, C the new parameter σ is introduced. This parameter characterizes the existence of fractional structures in the system. A relation between the fractional order time derivative ɣ and the new parameter σ is found. The numeric Laplace transform method was used for the simulation of the equations results. The results show that the fractional differential equations generalize the behavior of the charge, voltage and current depending of the values of ɣ. The classical cases are recovered by taking the limit when ɣ = 1. An analysis in the frequency domain of an RC circuit shows the application and use of fractional order differential equations.

Fatigue behavior of RC T-beams

Directory of Open Access Journals (Sweden)

Omar A. Farghal

2014-09-01

Full Text Available The objective of this research is to study the fatigue performance of reinforced concrete (RC T-beams strengthened in shear with Carbon Fiber Reinforced Polymer (CFRP composite. Experiments were conducted on RC beams with and without CFRP sheets bonded on their web surfaces and subjected to static and cycling loading. The obtained results showed that the strengthened beams could survive one million cycles of cyclic loading (=50% of maximum static load with no apparent signs of damage (premature failure demonstrating the effectiveness of CFRP strengthening system on extending the fatigue life of structures. Also, for beams having the same geometry, the applied strengthening technique can significantly enhance the cycling load particularly, in case of beams provided with U-jacket sheets. Moreover, although the failure mode for the different beams was a brittle one, the strengthened beams provided with U-jacket sheets approved an acceptable enhancement in the structural ductility.

Process, Voltage and Temperature Compensation Technique for Cascode Modulated PAs

DEFF Research Database (Denmark)

Sira, Daniel; Larsen, Torben

2013-01-01

, that represents a transistor level model (empirical model) of the cascode modulated PA, is utilized in a PA analog predistorter. The analog predistorter linearizes and compensates for PVT variation of the cascode modulated PA. The empirical model is placed in the negative feedback of an operational...... transconductance amplifier. The predistorted varying envelope signal is applied to the cascode gate of the PA. It is shown that the proposed PVT compensation technique significantly reduces the PVT spread of the PA linearity indicators and improves the PA linearity. Simulations were performed in a 0.13 μm CMOS...

Minimizing the energy spread within a single bunch by shaping its charge distribution

International Nuclear Information System (INIS)

Loew, G.A.; Wang, J.

1984-06-01

When electrons or positrons in a bunch pass through the periodic structure of a linear accelerator, they leave behind them energy in the form of longitudinal wake fields. The longitudinal fields left behind by early particles in a bunch decrease the energy of later particles. For a linear collider, the energy spread introduced within the bunches by this beam loading effect must be minimized because it limits the degree to which the particles can be focused to a small spot due to chromatic effects in the final focus system. For example, for the SLC, the allowable energy spread is +-0.5%. It has been known for some time that partial compensation of the longitudinal wake field effects can be obtained for any bunch by placing it ahead of the accelerating crest (in space), thereby letting the positive rising sinusoidal field offset the negative beam loading field. The work presented in this report shows that it is possible to obtain complete compensation, i.e., to reduce the energy spread essentially to zero by properly shaping the longitudinal charge distribution of the bunch and by placing it at the correct position on the wave

Cracking and Deformation Modelling of Tensile RC Members Using Stress Transfer Approach

Directory of Open Access Journals (Sweden)

Ronaldas Jakubovskis

2016-12-01

Full Text Available The paper presents a modeling technique for bond, cracking and deformation analysis of RC members. The proposed mod-eling technique is not restricted by the geometrical dimensions of the analyzed member and may be applied for various load-ing conditions. Tensile as well as bending RC members may be analyzed using the proposed technique. Adequacy of the modeling strategy was evaluated by the developed numerical discrete crack algorithm, which allows modeling deformation and cracking behavior of tensile RC members. Comparison of experimental and numerical results proved the applicability of the proposed modeling strategy.

Perbandingan Algoritma Enkripsi GGHN(8,8 dan RC4 Untuk Video Conference

Directory of Open Access Journals (Sweden)

Satriyo Satriyo

2012-01-01

Full Text Available Encryption is a solutions to secure the information transmitted through the medium of communication that can not be intercepted by unauthorized parties. This study implemented two algorithms i.e. RC4 and GGHN (8.8 in video conference. This study compared the speed  of  both  encryption  and  decryption  of  the  encryption  algorithm,  and  perform  measurements  of  bandwidth .  From  the  results  of measurements of the speed can be concluded that the RC4 algorithm is 1.53 times and 1.34 times faster than GGHN(8,8 for encryption and  decryption  audio  data.  The  encryption  and  decryption  video  data  RC4  are  1.44  times  and  1.09  times  faster  than  GHN(8,8. Bandwidth  usage  for  video  conferencing  without  encryption  and  bandwidth  usage  on  a  video  conference  with  RC4  encryption  and GGHN (8.8 is the same.Keywords: Video Conference; RC4; GGHN(8,8; Real Time Protocol.

Upgrading the seismic capacity of existing RC buildings using buckling restrained braces

Directory of Open Access Journals (Sweden)

Hamdy Abou-Elfath

2017-06-01

Full Text Available Many existing RC buildings do not meet the lateral strength requirements of current seismic codes and are vulnerable to significant damage or collapse in the event of future earthquakes. In the past few decades, buckling-restrained braces have become increasingly popular as a lateral force resisting system because of their capability of improving the strength, the stiffness and the energy absorbing capacity of structures. This study evaluates the seismic upgrading of a 6-story RC-building using single diagonal buckling restrained braces. Seismic evaluation in this study has been carried out by static pushover analysis and time history earthquake analysis. Ten ground motions with different PGA levels are used in the analysis. The mean plus one standard deviation values of the roof-drift ratio, the maximum story drift ratio, the brace ductility factors and the member strain responses are used as the basis for the seismic performance evaluations. The results obtained in this study indicate that strengthening of RC buildings with buckling restrained braces is an efficient technique as it significantly increases the PGA capacity of the RC buildings. The results also indicate the increase in the PGA capacity of the RC building with the increase in the amount of the braces.

Estimation methods of deformational behaviours of RC beams under the unrestrained condition at elevated temperatures

International Nuclear Information System (INIS)

Kanezu, Tsutomu; Nakano, Takehiro; Endo, Tatsumi

1986-01-01

The estimation methods of free deformations of reinforced concrete (RC) beams at elevated temperatures are investigated based on the concepts of ACI's and CEB/FIP's formulas, which are well used to estimate the flexural deformations of RC beams at normal temperature. Conclusions derived from the study are as follows. 1. Features of free deformations of RC beams. (i) The ratios of the average compressive strains on the top fiber of RC beams to the calculated ones at the cracked section show the inclinations that the ratios once drop after cracking and then remain constant according to temperature rises. (ii) Average compressive strains might be estimated by the average of the calculated strains at the perfect bond section and the cracked section of RC beam. (iii) The ratios of the average tensile strains on the level of reinforcements to the calculated ones at the cracked section are inclined to approach the value of 1.0 monotonically according to temperature rises. The changes of the average tensile strains are caused by the deterioration of bond strength and cracking due to the increase of the differences of expansive strains between reinforcement and concrete. 2. Estimation methods of free deformations of RC beams. (i) In order to estimate the free deformations of RC beams at elevated temperatures, the basic concepts of ACI's and CEB/FIP's formulas are adopted, which are well used to estimate the M-φ relations of RC beams at normal temperature. (ii) It was confirmed that the suggested formulas are able to estimate the free deformations of RC beams, that is, the longitudinal deformation and the curvature, at elevated temperatures. (author)

The calcium-dependent protein kinase RcCDPK2 phosphorylates sucrose synthase at Ser11 in developing castor oil seeds.

Science.gov (United States)

Fedosejevs, Eric T; Gerdis, Suzanne A; Ying, Sheng; Pyc, Michal; Anderson, Erin M; Snedden, Wayne A; Mullen, Robert T; She, Yi-Min; Plaxton, William C

2016-10-15

Imported sucrose is cleaved by sucrose synthase (SUS) as a critical initial reaction in the biosynthesis of storage end-products by developing seeds. Although SUS is phosphorylated at a conserved seryl residue by an apparent CDPK (Ca 2+ -dependent protein kinase) in diverse plant tissues, the functions and mechanistic details of this process remain obscure. Thus, the native CDPK that phosphorylates RcSUS1 (Ricinus communis SUS1) at Ser 11 in developing COS (castor oil seeds) was highly purified and identified as RcCDPK2 by MS/MS. Purified RcSUS1-K (-kinase) and heterologously expressed RcCDPK2 catalyzed Ca 2+ -dependent Ser 11 phosphorylation of RcSUS1 and its corresponding dephosphopeptide, while exhibiting a high affinity for free Ca 2+ ions [K 0.5 (Ca 2+ ) < 0.4 µM]. RcSUS1-K activity, RcCDPK2 expression, and RcSUS1 Ser 11 phosphorylation peaked during early COS development and then declined in parallel. The elimination of sucrose import via fruit excision triggered RcSUS1 dephosphorylation but did not alter RcSUS1-K activity, suggesting a link between sucrose signaling and posttranslational RcCDPK2 control. Both RcCDPK2-mCherry and RcSUS1-EYFP co-localized throughout the cytosol when transiently co-expressed in tobacco suspension cells, although RcCDPK2-mCherry was also partially localized to the nucleus. Subcellular fractionation revealed that ∼20% of RcSUS1-K activity associates with microsomal membranes in developing COS, as does RcSUS1. In contrast with RcCDPK1, which catalyzes inhibitory phosphorylation of COS bacterial-type phosphoenolpyruvate carboxylase at Ser 451 , RcCDPK2 exhibited broad substrate specificity, a wide pH-activity profile centered at pH 8.5, and insensitivity to metabolite effectors or thiol redox status. Our combined results indicate a possible link between cytosolic Ca 2+ -signaling and the control of photosynthate partitioning during COS development. © 2016 The Author(s); published by Portland Press Limited on behalf of the

Generation of equivalent forms of operational trans-conductance amplifier-RC sinusoidal oscillators: the nullor approach

Directory of Open Access Journals (Sweden)

Raj Senani

2014-06-01

Full Text Available It has been shown in two earlier papers published from this study that corresponding to a given single-operational trans-conductance amplifier (single-OTA-RC and dual-OTA-RC sinusoidal oscillators, there are three other structurally distinct equivalent forms having the same characteristic equation, one of which employs both grounded capacitors (GC. In this study, an earlier nullor-based theory of generating equivalent op-amp oscillator circuits, proposed by the first author, is extended to derive equivalent OTA-RC circuits which discloses the existence of an additional number of equivalent forms for the same given OTA-RC oscillators than those predicted by the quoted earlier works, and thereby considerably enlarging the set of equivalents of a given OTA-RC oscillator. Furthermore, the presented nullor-based theory of generating equivalent OTA-RC oscillators results in three additional interesting outcomes: (i the revelation that corresponding to any given OTA-RC oscillator there are two ‘both-GC’ oscillators (and not merely one, as derived in the quoted earlier works; (ii the availability of explicit current outputs in several of the derived equivalents and (iii the realisability explicit-current-output ‘quadrature oscillators’ in some of the generated equivalent oscillators. The workability of the generated equivalent OTA-RC oscillators has been verified by SPICE simulations, based on CMOS OTAs using 0.18 µm CMOS technology process parameters, and some sample results are given.

Experimental investigation of the seismic performance of the R/C frames with reinforced masonry infills

Science.gov (United States)

Tanjung, Jafril; Maidiawati, Nugroho, Fajar

2017-10-01

Intensive studies regarding the investigation of seismic performance of reinforced concrete (R/C) frames which are infilled with brick masonry walls have been carried out by several researchers within the last three-decades. According to authors' field and experimentally experiences conclude that the unreinforced brick masonry infills significantly contributes to increase the seismic performance of the R/C frame structure. Unfortunately, the presence of brick masonry infill walls causes several undesirable effects such as short column, soft-storey, torsion and out of plane collapse. In this study, a strengthening technique for the brick masonry infills were experimentally investigated to improve the seismic performance of the R/C frame structures. For this purpose, four experimental specimens have been prepared, i.e. one of bare R/C frame (BF), one of R/C frame infilled with unreinforced brick-masonry wall (IFUM) and two of R/C frames were infilled with reinforced brick-masonry wall (IFRM-1 and IFRM-2). The bare frame and R/C frame infilled with unreinforced brick-masonry wall represents the typical R/C buildings' construction in Indonesia assuming the brick-masonry wall as the non-structural elements. The brick-masonry wall infills in specimens IFRM-1 and IFRM-2 were strengthened by using embedded ϕ4 plain steel bar on their diagonal and center of brick-masonry wall, respectively. All specimens were laterally pushed-over. The lateral loading and its lateral displacement, failure mechanism and their crack pattern were recorded during experimental works. Comparison of the experimental results of these four specimens conclude that the strengthening of the brick-masonry infills wall gave the significantly increasing of the seismic performance of the R/C frame. The seismic performance was evaluated based on the lateral strength of the R/C specimen. The embedded plain steel bar on brick-masonry also reduces the diagonal crack on the brick-masonry wall. It seems that

Formulation development of retrocyclin 1 analog RC-101 as an anti-HIV vaginal microbicide product.

Science.gov (United States)

Sassi, A B; Cost, M R; Cole, A L; Cole, A M; Patton, D L; Gupta, P; Rohan, L C

2011-05-01

RC-101 is a synthetic microbicide analog of retrocyclin, which has shown in vitro activity against X4 and R5 HIV-1. In an effort to develop a safe and effective RC-101 vaginal microbicide product, we assessed safety in ex vivo macaque and human models and efficacy using in vitro and ex vivo models. A polyvinyl-alcohol vaginal film containing RC-101 (100 μg/film) was developed. Formulation assessment was conducted by evaluating disintegration, drug content, mechanical properties, and stability. Efficacy was evaluated by in vitro peripheral blood mononuclear cells (PBMC) assay and ex vivo human ectocervical tissue explant model. Ex vivo safety studies were conducted by exposing RC-101 to an excised monkey reproductive tract and excised human ectocervical tissue. RC-101 100 μg films were shown to be safe to human and monkey tissue and effective against HIV-1 in vitro and ex vivo in human ectocervical tissue. The 90% inhibitory concentration (IC90) for RC-101 films at 2,000 μg (IC90=57.5 μM) using an ex vivo model was 10-fold higher than the IC90 observed using an in vitro model (IC90=5.0 μM). RC-101 films were stable for 1 month at 25°C, with in vitro bioactivity maintained for up to 6 months. RC-101 was developed in a quick-dissolve film formulation that was shown to be safe in an ex vivo model and effective in in vitro and ex vivo models. RC-101 film formulations were shown to maintain bioactivity for a period of 6 months. Findings from the present study contribute to the development of a safe and effective topical microbicide product.

Shear Strengthening of RC Beams Using Sprayed Glass Fiber Reinforced Polymer

Directory of Open Access Journals (Sweden)

Sayed Mohamad Soleimani

2012-01-01

Full Text Available The effectiveness of externally bonded sprayed glass fiber reinforced polymer (Sprayed GFRP in shear strengthening of RC beams under quasi-static loading is investigated. Different techniques were utilized to enhance the bond between concrete and Sprayed GFRP, involving the use of through bolts and nuts paired with concrete surface preparation through sandblasting and through the use of a pneumatic chisel prior to Sprayed GFRP application. It was found that roughening the concrete surface using a pneumatic chisel and using through bolts and nuts were the most effective techniques. Also, Sprayed GFRP applied on 3 sides (U-shaped was found to be more effective than 2-sided Sprayed GFRP in shear strengthening. Sprayed GFRP increased the shear load-carrying capacity and energy absorption capacities of RC beams. It was found that the load-carrying capacity of strengthened RC beams was related to an effective strain of applied Sprayed GFRP. This strain was related to Sprayed GFRP configuration and the technique used to enhance the concrete-FRP bond. Finally, an equation was proposed to calculate the contribution of Sprayed GFRP in the shear strength of an RC beam.

Loss Characteristics of 6.5 kV RC-IGBT Applied to a Traction Converter

Directory of Open Access Journals (Sweden)

Xianjin Huang

2017-07-01

Full Text Available 6.5 kV level IGBT (Insulated Gate Bipolar Transistor modules are widely applied in megawatt locomotive (MCUs traction converters, to achieve an upper 3.5 kV DC link, which is beneficial for decreasing power losses and increasing the power density. Reverse Conducting IGBT (RC-IGBT constructs the conventional IGBT function and freewheel diode function in a single chip, which has a greater flow ability in the same package volume. In the same cooling conditions, RC-IGBT allows for a higher operating temperature. In this paper, a mathematic model is developed, referring to the datasheets and measurement data, to study the 6.5 kV/1000 A RC-IGBT switching features. The relationship among the gate desaturated pulse, conducting losses, and recovery losses is discussed. Simulations and tests were carried out to consider the influence of total losses on the different amplitudes and durations of the desaturated pulse. The RC-IGBT traction converter system with gate pulse desaturated control is built, and the simulation and measurements show that the total losses of RC-IGBT with desaturated control decreased comparing to the RC-IGBT without desaturated control or conventional IGBT. Finally, a proportional small power platform is developed, and the test results prove the correction of the theory analysis.

Development of an Improved Crack Propagation Model for Corrosion-Induced Cover Cracking in RC Structures

Science.gov (United States)

Hilyati, S.; Nizam, Z. M.; Zurisman, M. A. A.; Azhar, A. T. S.

2017-06-01

During the last two decades, reinforced concrete (RC) has been extensively used in most of the world as one of the common construction material due to its advantages and durability. However, RC structures exposed to marine environments are subjected to chloride attack. Chlorides from seawater penetrate into RC structures are not only causing severe corrosion problems but also affect the durability and serviceability of such structures. This paper investigates the influence of transverse reinforcement and spacing of reinforcing bars on concrete cover cracking of two-way RC slab specimens using accelerated corrosion tests. The experimental program involved the testing of four RC slab specimens and was generally designed to observe the crack width and the time of crack to propagate. An improved model for predicting the timing of crack propagation based on the experimental data was then developed.

GR712RC- Dual-Core Processor- Product Status

Science.gov (United States)

Sturesson, Fredrik; Habinc, Sandi; Gaisler, Jiri

2012-08-01

The GR712RC System-on-Chip (SoC) is a dual core LEON3FT system suitable for advanced high reliability space avionics. Fault tolerance features from Aeroflex Gaisler’s GRLIB IP library and an implementation using Ramon Chips RadSafe cell library enables superior radiation hardness.The GR712RC device has been designed to provide high processing power by including two LEON3FT 32- bit SPARC V8 processors, each with its own high- performance IEEE754 compliant floating-point-unit and SPARC reference memory management unit.This high processing power is combined with a large number of serial interfaces, ranging from high-speed links for data transfers to low-speed control buses for commanding and status acquisition.

Deformation Analysis of RC Ties Externally Strengthened with FRP Sheets

Science.gov (United States)

Gribniak, V.; Arnautov, A. K.; Kaklauskas, G.; Jakstaite, R.; Tamulenas, V.; Gudonis, E.

2014-11-01

The current study has two objectives: to validate the ability of the Atena finite-element software to estimate the deformations of reinforced concrete (RC) elements strengthened with fiber-reinforced polymer (FRP) sheets and to assess the effect of FRP-to-concrete bond strength on the results of numerical simulation. It is shown that the bond strength has to be selected according to the overall stiffness of the composite element. The numerical results found are corroborated experimentally by tensile tests of RC elements strengthened with basalt FRP sheets.

Observations on out-of-plane behaviour of URM walls in buildings with RC slabs

OpenAIRE

Tondelli, Marco; Beyer, Katrin

2014-01-01

In Switzerland many new residential buildings are constructed as unreinforced masonry (URM) structures or as mixed structures where URM walls are coupled with reinforced concrete (RC) walls by RC slabs. At present the boundary conditions of URM walls subjected to out-of-plane accelerations are still not well quantified. In the framework of a large research activity on RC-URM wall structures a shake-table test on a four-storey mixed structure was performed. The test specimen, which was built a...

Mouse RC/BTB2, a Member of the RCC1 Superfamily, Localizes to Spermatid Acrosomal Vesicles

Science.gov (United States)

Shen, Xuening; Nagarkatti-Gude, David R.; Hess, Rex A.; Henderson, Scott C.; Strauss, Jerome F.; Zhang, Zhibing

2012-01-01

Mouse RC/BTB2 is an unstudied protein of the RCC1 (Regulator of Chromosome Condensation) superfamily. Because of the significant remodeling of chromatin that occurs during spermiogenesis, we characterized the expression and localization of mouse RC/BTB2 in the testis and male germ cells. The Rc/btb2 gene yields two major transcripts: 2.3 kb Rc/btb2-s, present in most somatic tissues examined; and 2.5 kb Rc/btb2-t, which contains a unique non-translated exon in its 5′-UTR that is only detected in the testis. During the first wave of spermatogenesis, Rc/btb2-t mRNA is expressed from day 8 after birth, reaching highest levels of expression at day 30 after birth. The full-length protein contains three RCC1 domains in the N-terminus, and a BTB domain in the C-terminus. In the testis, the protein is detectable from day 12, but is progressively up-regulated to day 30 and day 42 after birth. In spermatids, some of the protein co-localizes with acrosomal markers sp56 and peanut lectin, indicating that it is an acrosomal protein. A GFP-tagged RCC1 domain is present throughout the cytoplasm of transfected CHO cells. However, both GFP-tagged, full-length RC/BTB2 and a GFP-tagged BTB domain localize to vesicles in close proximity to the nuclear membrane, suggesting that the BTB domain might play a role in mediating full-length RC/BTB2 localization. Since RCC1 domains associate with Ran, a small GTPase that regulates molecular trafficking, it is possible that RC/BTB2 plays a role in transporting proteins during acrosome formation. PMID:22768142

Seismic Rehabilitation of RC Frames by Using Steel Panels

Science.gov (United States)

Mowrtage, Waiel

2008-07-01

Every major earthquake in Turkey causes a large number of building suffer moderate damage due to poor construction. If a proper and fast retrofit is not applied, the aftershocks, which may sometimes come days or weeks after the main shock, can push a moderately damaged building into a major damage or even total collapse. This paper presents a practical retrofit method for moderately damaged buildings, which increases the seismic performance of the structural system by reducing the displacement demand. Fabricated steel panels are used for the retrofit. They are light-weight, easy to handle, and can be constructed very quickly. Moreover, they are cheap, and do not need formwork or skilled workers. They can be designed to compensate for the stiffness and strength degradation, and to fit easily inside a moderately damaged reinforced concrete frame. To test the concept, a half-scale, single-story 3D reinforced concrete frame specimen was constructed at the shake-table laboratories of the Kandilli Observatory and Earthquake Research Institute of Bogazici University, and subjected to recorded real earthquake base accelerations. The amplitudes of base accelerations were increased until a moderate damage level is reached. Then, the damaged RC frames was retrofitted by means of steel panels and tested under the same earthquake. The seismic performance of the specimen before and after the retrofit was evaluated using FEMA356 standards, and the results were compared in terms of stiffness, strength, and deformability. The results have confirmed effectiveness of the proposed retrofit scheme.

Seismic Rehabilitation of RC Frames by Using Steel Panels

International Nuclear Information System (INIS)

Mowrtage, Waiel

2008-01-01

Every major earthquake in Turkey causes a large number of building suffer moderate damage due to poor construction. If a proper and fast retrofit is not applied, the aftershocks, which may sometimes come days or weeks after the main shock, can push a moderately damaged building into a major damage or even total collapse. This paper presents a practical retrofit method for moderately damaged buildings, which increases the seismic performance of the structural system by reducing the displacement demand. Fabricated steel panels are used for the retrofit. They are light-weight, easy to handle, and can be constructed very quickly. Moreover, they are cheap, and do not need formwork or skilled workers. They can be designed to compensate for the stiffness and strength degradation, and to fit easily inside a moderately damaged reinforced concrete frame.To test the concept, a half-scale, single-story 3D reinforced concrete frame specimen was constructed at the shake-table laboratories of the Kandilli Observatory and Earthquake Research Institute of Bogazici University, and subjected to recorded real earthquake base accelerations. The amplitudes of base accelerations were increased until a moderate damage level is reached. Then, the damaged RC frames was retrofitted by means of steel panels and tested under the same earthquake. The seismic performance of the specimen before and after the retrofit was evaluated using FEMA356 standards, and the results were compared in terms of stiffness, strength, and deformability. The results have confirmed effectiveness of the proposed retrofit scheme

Preformulation and stability in biological fluids of the retrocyclin RC-101, a potential anti-HIV topical microbicide

Directory of Open Access Journals (Sweden)

Conrads Thomas P

2011-07-01

Full Text Available Abstract Background RC-101, a cationic peptide retrocyclin analog, has in vitro activity against HIV-1. Peptide drugs are commonly prone to conformational changes, oxidation and hydrolysis when exposed to excipients in a formulation or biological fluids in the body, this can affect product efficacy. We aimed to investigate RC-101 stability under several conditions including the presence of human vaginal fluids (HVF, enabling the efficient design of a safe and effective microbicide product. Stability studies (temperature, pH, and oxidation were performed by HPLC, Circular Dichroism, and Mass Spectrometry (LC-MS/MS. Additionally, the effect of HVF on formulated RC-101 was evaluated with fluids collected from healthy volunteers, or from subjects with bacterial vaginosis (BV. RC-101 was monitored by LC-MS/MS for up to 72 h. Results RC-101 was stable at pH 3, 4, and 7, at 25 and 37°C. High concentrations of hydrogen peroxide resulted in less than 10% RC-101 reduction over 24 h. RC-101 was detected 48 h after incubation with normal HVF; however, not following incubation with HVF from BV subjects. Conclusions Our results emphasize the importance of preformulation evaluations and highlight the impact of HVF on microbicide product stability and efficacy. RC-101 was stable in normal HVF for at least 48 h, indicating that it is a promising candidate for microbicide product development. However, RC-101 stability appears compromised in individuals with BV, requiring more advanced formulation strategies for stabilization in this environment.

Energy transfer dynamics in an RC-LH1-PufX tubular photosynthetic membrane

International Nuclear Information System (INIS)

Hsin, J; Sener, M; Schulten, K; Struempfer, J; Qian, P; Hunter, C N

2010-01-01

Light absorption and the subsequent transfer of excitation energy are the first two steps in the photosynthetic process, carried out by protein-bound pigments, mainly bacteriochlorophylls (BChls), in photosynthetic bacteria. BChls are anchored in light-harvesting (LH) complexes, such as light-harvesting complex I (LH1), which directly associates with the reaction center (RC), forming the RC-LH1 core complex. In Rhodobacter sphaeroides, RC-LH1 core complexes contain an additional protein, PufX, and assemble into dimeric RC-LH1-PufX core complexes. In the absence of LH complex II (LH2), the former complexes can aggregate into a helically ordered tubular photosynthetic membrane. We have examined the excitation transfer dynamics in a single RC-LH1-PufX core complex dimer using the hierarchical equations of motion for dissipative quantum dynamics that accurately, yet in a computationally costly manner, treat the coupling between BChls and their protein environment. A widely employed description, the generalized Foerster (GF) theory, was also used to calculate the transfer rates of the same excitonic system in order to verify the accuracy of this computationally cheap method. Additionally, in light of the structural uncertainties in the Rba. sphaeroides RC-LH1-PufX core complex, geometrical alterations were introduced into the BChl organization. It is shown that the energy transfer dynamics are not affected by the considered changes in the BChl organization and that the GF theory provides accurate transfer rates. An all-atom model for a tubular photosynthetic membrane is then constructed on the basis of electron microscopy data, and the overall energy transfer properties of this membrane are computed.

Energy transfer dynamics in an RC-LH1-PufX tubular photosynthetic membrane

Energy Technology Data Exchange (ETDEWEB)

Hsin, J; Sener, M; Schulten, K [Department of Physics and Beckman Institute, University of Illinois at Urbana-Champaign, Urbana (United States); Struempfer, J [Center for Biophysics and Computational Biology and Beckman Institute, University of Illinois at Urbana-Champaign, Urbana (United States); Qian, P; Hunter, C N, E-mail: kschulte@ks.uiuc.ed [Department of Molecular Biology and Biotechnology, University of Sheffield, Sheffield S10 2TN (United Kingdom)

2010-08-15

Light absorption and the subsequent transfer of excitation energy are the first two steps in the photosynthetic process, carried out by protein-bound pigments, mainly bacteriochlorophylls (BChls), in photosynthetic bacteria. BChls are anchored in light-harvesting (LH) complexes, such as light-harvesting complex I (LH1), which directly associates with the reaction center (RC), forming the RC-LH1 core complex. In Rhodobacter sphaeroides, RC-LH1 core complexes contain an additional protein, PufX, and assemble into dimeric RC-LH1-PufX core complexes. In the absence of LH complex II (LH2), the former complexes can aggregate into a helically ordered tubular photosynthetic membrane. We have examined the excitation transfer dynamics in a single RC-LH1-PufX core complex dimer using the hierarchical equations of motion for dissipative quantum dynamics that accurately, yet in a computationally costly manner, treat the coupling between BChls and their protein environment. A widely employed description, the generalized Foerster (GF) theory, was also used to calculate the transfer rates of the same excitonic system in order to verify the accuracy of this computationally cheap method. Additionally, in light of the structural uncertainties in the Rba. sphaeroides RC-LH1-PufX core complex, geometrical alterations were introduced into the BChl organization. It is shown that the energy transfer dynamics are not affected by the considered changes in the BChl organization and that the GF theory provides accurate transfer rates. An all-atom model for a tubular photosynthetic membrane is then constructed on the basis of electron microscopy data, and the overall energy transfer properties of this membrane are computed.

SEISMICALLY RETROFITTING AND UPGRADING RC-MRF BY USING EXPANDED METAL PANELS

OpenAIRE

Phung Ngoc, Dung

2011-01-01

Reinforced concrete moment resisting frames (RC-MRFs) have been widely used as the main structural resisting systems for over 30 years based on their capacity in resisting both gravity loads and lateral forces like winds or earthquakes and on low cost of construction. However, there have been still many existing RC-MRFs not designed according to any modern seismic code. This may lead to some undesired failures under a rather low intensity earthquake. There are several existing retrofitting sy...

Minimizing the energy spread within a single bunch by shaping its charge distribution

International Nuclear Information System (INIS)

Loew, G.A.; Wang, J.W.

1985-03-01

It has been known for some time that partial compensation of the longitudinal wake field effects can be obtained for any bunch by placing it ahead of the accelerating crest (in space), thereby letting the positive rising sinusoidal field offset the negative beam loading field. The work presented in this paper shows that it is possible to obtain complete compensation, i.e., to reduce the energy spread essentially to zero by properly shaping the longitudinal charge distribution of the bunch and by placing it at the correct position on the wave. 3 refs., 5 figs., 3 tabs

An experimental investigation for external RC shear wall applications

Science.gov (United States)

Kaltakci, M. Y.; Ozturk, M.; Arslan, M. H.

2010-09-01

The strength and rigidity of most reinforced concrete (RC) buildings in Turkey, which are frequently hit by destructive earthquakes, is not at a sufficient level. Therefore, the result of earthquakes is a significant loss of life and property. The strengthening method most commonly preferred for these type of RC buildings is the application of RC infilled walls (shear walls) in the frame openings of the building. However, since the whole building has to be emptied and additional heavy costs arise during this type of strengthening, users prefer not to strengthen their buildings despite the heavy risk they are exposed to. Therefore, it is necessary to develop easier-to-apply and more effective methods for the rapid strengthening of housing and the heavily-used public buildings which cannot be emptied during the strengthening process (such as hospitals and schools). This study empirically analyses the different methods of a new system which can meet this need. In this new system, named "external shear wall application", RC shear walls are applied on the external surface of the building, along the frame plane rather than in the building. To this end, 7 test samples in 1/2 and 1/3 geometrical scale were designed to analyse the efficiency of the strengthening technique where the shear wall leans on the frame from outside of the building (external shear wall application) and of the strengthening technique where a specific space is left between the frame and the external shear wall by using a coupling beam to connect elements (application of external shear wall with coupling beam). Test results showed that the maximum lateral load capacity, initial rigidity and energy dissipation behaviours of the samples strengthened with external shear wall were much better than those of the bare frames.

An experimental investigation for external RC shear wall applications

Directory of Open Access Journals (Sweden)

M. Y. Kaltakci

2010-09-01

Full Text Available The strength and rigidity of most reinforced concrete (RC buildings in Turkey, which are frequently hit by destructive earthquakes, is not at a sufficient level. Therefore, the result of earthquakes is a significant loss of life and property. The strengthening method most commonly preferred for these type of RC buildings is the application of RC infilled walls (shear walls in the frame openings of the building. However, since the whole building has to be emptied and additional heavy costs arise during this type of strengthening, users prefer not to strengthen their buildings despite the heavy risk they are exposed to. Therefore, it is necessary to develop easier-to-apply and more effective methods for the rapid strengthening of housing and the heavily-used public buildings which cannot be emptied during the strengthening process (such as hospitals and schools. This study empirically analyses the different methods of a new system which can meet this need. In this new system, named "external shear wall application", RC shear walls are applied on the external surface of the building, along the frame plane rather than in the building. To this end, 7 test samples in 1/2 and 1/3 geometrical scale were designed to analyse the efficiency of the strengthening technique where the shear wall leans on the frame from outside of the building (external shear wall application and of the strengthening technique where a specific space is left between the frame and the external shear wall by using a coupling beam to connect elements (application of external shear wall with coupling beam. Test results showed that the maximum lateral load capacity, initial rigidity and energy dissipation behaviours of the samples strengthened with external shear wall were much better than those of the bare frames.

Shear Strengthening of RC Deep Beam Using Externally Bonded GFRP Fabrics

Science.gov (United States)

Kumari, A.; Patel, S. S.; Nayak, A. N.

2018-06-01

This work presents the experimental investigation of RC deep beams wrapped with externally bonded Glass Fibre Reinforced Polymer (GFRP) fabrics in order to study the Load versus deflection behavior, cracking pattern, failure modes and ultimate shear strength. A total number of five deep beams have been casted, which is designed with conventional steel reinforcement as per IS: 456 (Indian standard plain and reinforced concrete—code for practice, Bureau of Indian Standards, New Delhi, 2000). The spans to depth ratio for all RC deep beams have been kept less than 2 as per the above specification. Out of five RC deep beams, one without retrofitting serves as a reference beam and the rest four have been wrapped with GFRP fabrics in multiple layers and tested with two point loading condition. The first cracking load, ultimate load and the shear contribution of GFRP to the deep beams have been observed. A critical discussion is made with respect to the enhancement of the strength, behaviour and performance of retrofitted deep beams in comparison to the deep beam without GFRP in order to explore the potential use of GFRP for strengthening the RC deep beams. Test results have demonstrated that the deep beams retrofitted with GFRP shows a slower development of the diagonal cracks and improves shear carrying capacity of the RC deep beam. A comparative study of the experimental results with the theoretical ones predicted by various researchers available in the literatures has also been presented. It is observed that the ultimate load of the beams retrofitted with GFRP fabrics increases with increase of number of GFRP layers up to a specific number of layers, i.e. 3 layers, beyond which it decreases.

ECE diagnostics for RTO/RC ITER

International Nuclear Information System (INIS)

Vayakis, G.; Bartlett, D.V.; Costley, A.E.

2001-01-01

This paper presents the current status of the Electron Cyclotron Emission (ECE) diagnostic on the Reduced Technical Objectives/Reduced Cost International Thermonuclear Experimental Reactor (RTO/RC ITER). It discusses the implications of the new machine design on the measurement requirements, the ability of the diagnostic technique to meet these, and the changes in the implementation imposed by the new layout. Finally, it outlines the physics studies, design and R and D work required prior to the detailed design and construction of the diagnostic. Key results are: (i) that the localisation of the measurement is similar to that in ITER-FDR (40-100 mm in X-mode, 60-200 mm in O-mode for the reference scenario), so that the relative spatial resolution degrades in this, smaller, machine, and (ii) the expected effect of transport barriers on the temperature profile in the high temperature region will be poorly resolved, because the effect of the temperature gradient on the outboard side is to degrade the resolution to (∼250 mm in X-mode, ∼350 mm in O-mode). Nevertheless ECE will be able to make a unique and useful contribution to the RTO/RC ITER measurement set

Enhanced resistance to stripe rust disease in transgenic wheat expressing the rice chitinase gene RC24.

Science.gov (United States)

Huang, Xuan; Wang, Jian; Du, Zhen; Zhang, Chen; Li, Lan; Xu, Ziqin

2013-10-01

Stripe rust is a devastating fungal disease of wheat worldwide which is primarily caused by Puccinia striiformis f. sp tritici. Transgenic wheat (Triticum aestivum L.) expressing rice class chitinase gene RC24 were developed by particle bombardment of immature embryos and tested for resistance to Puccinia striiformis f.sp tritici. under greenhouse and field conditions. Putative transformants were selected on kanamycin-containing media. Polymease chain reaction indicated that RC24 was transferred into 17 transformants obtained from bombardment of 1,684 immature embryos. Integration of RC24 was confirmed by Southern blot with a RC24-labeled probe and expression of RC24 was verified by RT-PCR. Nine transgenic T1 lines exhibited enhanced resistance to stripe rust infection with lines XN8 and BF4 showing the highest level of resistance. Southern blot hybridization confirmed the stable inheritance of RC24 in transgenic T1 plants. Resistance to stripe rust in transgenic T2 and T3 XN8 and BF4 plants was confirmed over two consecutive years in the field. Increased yield (27-36 %) was recorded for transgenic T2 and T3 XN8 and BF4 plants compared to controls. These results suggest that rice class I chitinase RC24 can be used to engineer stripe rust resistance in wheat.

Direct Observation of Energy Detrapping in LH1-RC Complex by Two-Dimensional Electronic Spectroscopy.

Science.gov (United States)

Ma, Fei; Yu, Long-Jiang; Hendrikx, Ruud; Wang-Otomo, Zheng-Yu; van Grondelle, Rienk

2017-01-18

The purple bacterial core light harvesting antenna-reaction center (LH1-RC) complex is the simplest system able to achieve the entire primary function of photosynthesis. During the past decade, a variety of photosynthetic proteins were studied by a powerful technique, two-dimensional electronic spectroscopy (2DES). However, little attention has been paid to LH1-RC, although its reversible uphill energy transfer, trapping, and backward detrapping processes, represent a crucial step in the early photosynthetic reaction dynamics. Thus, in this work, we employed 2DES to study two LH1-RC complexes of Thermochromatium (Tch.) tepidum. By direct observation of detrapping, the complex reversible process was clearly identified and an overall scheme of the excitation evolution in LH1-RC was obtained.

Modeling of R/C Servo Motor and Application to Underactuated Mechanical Systems

Science.gov (United States)

Ishikawa, Masato; Kitayoshi, Ryohei; Wada, Takashi; Maruta, Ichiro; Sugie, Toshiharu

An R/C servo motor is a compact package of a DC geard-motor associated with a position servo controller. They are widely used in small-sized robotics and mechatronics by virtue of their compactness, easiness-to-use and high/weight ratio. However, it is crucial to clarify their internal model (including the embedded position servo) in order to improve control performance of mechatronic systems using R/C servo motors, such as biped robots or underactuted sysyems. In this paper, we propose a simple and realistic internal model of the R/C servo motors including the embedded servo controller, and estimate their physical parameters using continuous-time system identification method. We also provide a model of reference-to-torque transfer function so that we can estimate the internal torque acting on the load.

Development of a hysteresis model for R/C columns subjected to bi-axial lateral loading

International Nuclear Information System (INIS)

Dutta, Sekhar Chandra; Chowdhury, Rajib; Roy, Raghupati; Reddy, G. Rami

2003-01-01

Recent investigations on dynamic response of reinforced concrete (R/C) structures have confirmed that the R/C structural members undergo much more inelastic deformation in each of the two mutually perpendicular directions under bi-directional seismic loading, than that observed only under unidirectional ground motion. To predict the seismic response of R/C structure with fair accuracy demands, a faithful model that can incorporate the effect of biaxial bending interaction in column. This model should not have high computational demand but should adequately reflect the stiffness degrading and strength deterioration characteristics of R/C structural members. Present study is an effort to develop such a bi-directional hysteresis model accounting the effect of interaction between lateral loadings in two orthogonal directions. The development of the present model is based on the yield surface approach and it can incorporate both strength and stiffness degradation characteristics, which is unavoidable in R/C structures during cyclic loading. The performance of the proposed model/ is demonstrated through the prediction of available experimental results of a reinforced concrete column, subjected to biaxial loading. (author)

A reconfigurable complex band-pass filter with improved passive compensation

International Nuclear Information System (INIS)

Fan Chaojie; Mo Tingting; Chen Dongpo; Zhou Jianjun

2012-01-01

This paper presents a 5th-order Chebyshev-I active RC complex filter for multi-mode multi-band global navigation satellite systems (GNSS) RF receivers. An improved passive compensation technique is used to cancel the excess phase lag of the integrators, thus ensuring the in-band flatness of the frequency response over various ambient conditions. The filter has a programmable gain from 0 to 42 dB with a 6 dB step, a tunable center frequency at either 6.4 MHz or 16 MHz, and a bandwidth from 2 to 20 MHz with less than 3% frequency uncertainty. Implemented in a 0.18 μm CMOS process, the whole filter consumes 7.8 mA from a 1.8 V supply voltage and occupies a die area of 0.4 mm 2 . (semiconductor integrated circuits)

KOMBINASI ALGORITMA AES, RC4 DAN ELGAMAL DALAM SKEMA HYBRID UNTUK KEAMANAN DATA

Directory of Open Access Journals (Sweden)

Adi Widarma

2016-01-01

Full Text Available Abstrak — Pengiriman atau pertukaran data adalah hal yang sering terjadi dalam dunia teknologi informasi. Data yang dikirim kadang sering berisi data informasi yang penting bahkan sangat rahasia dan harus dijaga keamanannya. Untuk menjaga keamanan data, dapat dilakukan dengan menggunakan teknik kriptografi. Algoritma AES dan RC4 adalah salah satu dari algoritma simetri. Kelemahan dari algoritma simetri adalah proses enkripsi dan dekripsi menggunakan kunci yang sama. Untuk mengatasi tersebut dilakukan dengan menggunakan algoritma Elgamal. Algoritma Elgamal adalah termasuk algoritma asimetri. Algoritma Elgamal  digunakan untuk mengamankan kunci dari algoritma AES dan RC4. Peningkatan keamanan pesan dan kunci dilakukan dengan algoritma hybrid. Algoritma hybrid dengan mengkombinasikan beberapa algoritma baik algoritma simetri maupun algortima asimetri akan menambah keamanan sehingga menjadi lebih aman dan powerful (Jain & Agrawal 2014. Penelitian ini akan dilakukan metode hybrid yaitu mengkombinasikan beberapa algoritma kriptografi dengan menggunakan algoritma Advanced Encryption Standard (AES dan RC4 untuk kerahasiaan data serta algoritma Elgamal digunakan untuk enkripsi dan dekripsi kunci. Kata Kunci :  kriptograpi, algoritma AES, RC4, Elgamal, hybrid

RC Beams Strengthened with Mechanically Fastened Composites: Experimental Results and Numerical Modeling

Directory of Open Access Journals (Sweden)

Enzo Martinelli

2014-03-01

Full Text Available The use of mechanically-fastened fiber-reinforced polymer (MF-FRP systems has recently emerged as a competitive solution for the flexural strengthening of reinforced concrete (RC beams and slabs. An overview of the experimental research has proven the effectiveness and the potentiality of the MF-FRP technique which is particularly suitable for emergency repairs or when the speed of installation and immediacy of use are imperative. A finite-element (FE model has been recently developed by the authors with the aim to simulate the behavior of RC beams strengthened in bending by MF-FRP laminates; such a model has also been validated by using a wide experimental database collected from the literature. By following the previous study, the FE model and the assembled database are considered herein with the aim of better exploring the influence of some specific aspects on the structural response of MF-FRP strengthened members, such as the bearing stress-slip relationship assumed for the FRP-concrete interface, the stress-strain law considered for reinforcing steel rebars and the cracking process in RC members resulting in the well-known tension stiffening effect. The considerations drawn from this study will be useful to researchers for the calibration of criteria and design rules for strengthening RC beams through MF-FRP laminates.

Hypomethylation of IL17RC Promoter Associates with Age-related Macular Degeneration

Science.gov (United States)

Wei, Lai; Liu, Baoying; Tuo, Jingsheng; Shen, Defen; Chen, Ping; Li, Zhiyu; Liu, Xunxian; Ni, Jia; Dagur, Pradeep; Sen, H. Nida; Jawad, Shayma; Ling, Diamond; Park, Stanley; Chakrabarty, Sagarika; Meyerle, Catherine; Agron, Elvira; Ferris, Frederick L.; Chew, Emily Y.; McCoy, J. Philip; Blum, Emily; Francis, Peter J.; Klein, Michael L.; Guymer, Robyn H.; Baird, Paul N.; Chan, Chi-Chao; Nussenblatt, Robert B.

2012-01-01

SUMMARY Age related macular degeneration (AMD) is the leading cause of irreversible blindness in the elderly population worldwide. While recent studies have demonstrated strong genetic associations of single nucleotide polymorphisms within a number of genes and AMD, other modes of regulation are also likely to play a role in its etiology. We identified a significantly decreased level of methylation on the IL17RC promoter in AMD patients. Further, we showed that hypomethylation of the IL17RC promoter in AMD patients led to an elevated expression of its protein and mRNA in peripheral blood as well as in the affected retina and choroid, suggesting that the DNA methylation pattern and expression of IL17RC may potentially serve as a biomarker for the diagnosis of AMD and likely plays a role in disease pathogenesis. PMID:23177625

Centrifuge modeling of rocking-isolated inelastic RC bridge piers.

Science.gov (United States)

Loli, Marianna; Knappett, Jonathan A; Brown, Michael J; Anastasopoulos, Ioannis; Gazetas, George

2014-12-01

Experimental proof is provided of an unconventional seismic design concept, which is based on deliberately underdesigning shallow foundations to promote intense rocking oscillations and thereby to dramatically improve the seismic resilience of structures. Termed rocking isolation , this new seismic design philosophy is investigated through a series of dynamic centrifuge experiments on properly scaled models of a modern reinforced concrete (RC) bridge pier. The experimental method reproduces the nonlinear and inelastic response of both the soil-footing interface and the structure. To this end, a novel scale model RC (1:50 scale) that simulates reasonably well the elastic response and the failure of prototype RC elements is utilized, along with realistic representation of the soil behavior in a geotechnical centrifuge. A variety of seismic ground motions are considered as excitations. They result in consistent demonstrably beneficial performance of the rocking-isolated pier in comparison with the one designed conventionally. Seismic demand is reduced in terms of both inertial load and deck drift. Furthermore, foundation uplifting has a self-centering potential, whereas soil yielding is shown to provide a particularly effective energy dissipation mechanism, exhibiting significant resistance to cumulative damage. Thanks to such mechanisms, the rocking pier survived, with no signs of structural distress, a deleterious sequence of seismic motions that caused collapse of the conventionally designed pier. © 2014 The Authors Published by John Wiley & Sons Ltd.

3-D Image Encryption Based on Rubik's Cube and RC6 Algorithm

Science.gov (United States)

Helmy, Mai; El-Rabaie, El-Sayed M.; Eldokany, Ibrahim M.; El-Samie, Fathi E. Abd

2017-12-01

A novel encryption algorithm based on the 3-D Rubik's cube is proposed in this paper to achieve 3D encryption of a group of images. This proposed encryption algorithm begins with RC6 as a first step for encrypting multiple images, separately. After that, the obtained encrypted images are further encrypted with the 3-D Rubik's cube. The RC6 encrypted images are used as the faces of the Rubik's cube. From the concepts of image encryption, the RC6 algorithm adds a degree of diffusion, while the Rubik's cube algorithm adds a degree of permutation. The simulation results demonstrate that the proposed encryption algorithm is efficient, and it exhibits strong robustness and security. The encrypted images are further transmitted over wireless Orthogonal Frequency Division Multiplexing (OFDM) system and decrypted at the receiver side. Evaluation of the quality of the decrypted images at the receiver side reveals good results.

THE INFLUENCE OF JOB STRESS AND COMPENSATION TO JOB SATISFACTION AT PT. TRI MEGAH MAKMUR

Directory of Open Access Journals (Sweden)

I Ketut R Sudiarditha

2016-09-01

Full Text Available The purpose of this research are: 1 To know description and how picture level job stress, compensation and job satisfaction at PT Tri Megah Makmur. 2 To know the influence of job stress tojob satisfaction at PT Tri Megah Makmur. 3 To know the influence of compensation to job satisfaction at PT Tri Megah Makmur. 4 To know empirically the influence of job stress and compensation tojob satisfaction at PT Tri Megah Makmur. 5 To know how far the contribution of job stress and compensation to job satisfaction at PT Tri Megah Makmur. This research is using descriptive and explanatory survey analysis. This research is taken to 70 sales employees at PT Tri Megah Makmur, While the data collection technique was carried out by spreading kuisioner, which are then processed using SPSS versi 21.00.The analysis shows that: 1 level of compensation and job satisfaction are on a lower level, while the job stress are high. 2Job stress have negative effects and significantly on job satisfaction. 3 compensation have positive effect and significantly on job satisfaction. 4 job stress and compensation significantly influence on job satisfaction.

Seismic Performance of Multi-Span RC Railway Bridges

DEFF Research Database (Denmark)

Georgakis, Christos; Barrau, Xavier

2008-01-01

Presently, there is no clear method for determining the optimal railway bridge design for a particular ground type and expected seismic intensity. Four main types of RC bridge dominate the current multi-span railway bridge design trends – the Simply Supported Beam, Continuous Box-Girder (CBG), CBG...

The snap-back effect of an RC-IGBT and its simulations

International Nuclear Information System (INIS)

Zhang Wenliang; Tian Xiaoli; Zhu Yangjun; Tan Jingfei

2013-01-01

The RC-IGBT (reverse conducting insulated gate bipolar transistor) is a new kind of power semiconductor device which has many advantages such as smaller chip size, higher power density, lower manufacturing cost, softer turn off behavior, and better reliability. However, its performance has a number of drawbacks, such as the snap-back effect. In this paper, an introduction about the snap-back effect of the RC-IGBT is given firstly. Then the physical explanations are presented with two simplified models. After that, some numerical simulations are carried out to verify the correctness of the models. (semiconductor devices)

Investigation on Strengthening Approaches Adopted for Poorly Detailed RC Corbels

Directory of Open Access Journals (Sweden)

Ram Chandra Neupane

2017-05-01

Full Text Available Poor detailing of the position of bearing pad over reinforced concrete (RC corbel may lead to premature failure, which is undesired and structurally vulnerable. An appropriate retrofitting solution is necessary to ensure the functionality of such RC corbels. Considering the growing popularity of external carbon fiber-reinforced polymer (CFRP in retrofitting, this research examines the effectiveness of an externally wrapped unidirectional CFRP sheet and compares its performance against traditional retrofitting methods. Moreover, it is intended to fulfill the lack of extensive research on external CFRP application for corbel strengthening. A total of eight medium-scale corbel specimens were tested on vertical load. Observed premature failure due to placing the bearing pad near the edge of corbel was verified and the effectiveness of the proposed structural strengthening solutions was studied. Experimental results show that although the loading capacity of the damaged corbel due to the poor detailing of bearing pad position could not be fully recovered, the external CFRP wrapping method demonstrated superior performance over RC jacketing and was able to prevent localized failure. Further study based on non-linear 3D finite element analysis (FEA was carried out to identify the governing parameters of each retrofitting solution. Numerical studies suggested important parameters of various retrofitting alternatives for higher capacity assurance.

Investigation on the thermographic detection of corrosion in RC structures

Science.gov (United States)

Tantele, Elia A.; Votsis, Renos A.; Kyriakides, Nicholas; Georgiou, Panagiota G.; Ioannou, Fotia G.

2017-09-01

Corrosion of the steel reinforcement is the main problem of reinforced concrete (RC) structures. Over the past decades, several methods have been developed aiming to detect the corrosion process early in order to minimise the structural damage and consequently the repairing costs. Emphasis was given in developing methods and techniques of non-destructive nature providing fast on-the-spot detection and covering large areas rather that concentrating on single locations. This study, investigates a non-destructive corrosion detection technique for reinforced concrete, which is based on infrared thermography and the difference in thermal characteristics of corroded and non-corroded steel rebars. The technique is based on the principle that corrosion products have poor heat conductivity, and they inhibit the diffusion of heat that is generated in the reinforcing bar due to heating. For the investigation RC specimens, have been constructed in the laboratory using embedded steel bars of different corrosion states. Afterward, one surface of the specimens was heated using an electric device while thermal images were captured at predefined time instants on the opposite surface with an IR camera. The test results showed a clear difference between the thermal characteristics of the corroded and the non-corroded samples, which demonstrates the potential of using thermography in corrosion detection in RC structures.

Interfacial stresses in damaged RC beams strengthened with externally bonded CFRP plate

International Nuclear Information System (INIS)

Benrahou, K.H.; Adda bedia, E.A.; Benyoucef, S.; Tounsi, A.; Benguediab, M.

2006-01-01

A theoretical method to predict the interfacial stresses in the adhesive layer of damaged reinforced concrete beams strengthened with externally bonded carbon fiber-reinforced polymer (CFRP) plate is presented. The adopted model is developed including the adherend shear deformations by assuming a linear shear stress through the depth of the RC beam [A. Tounsi, Int. J. Solids Struct., in press], while all existing solutions neglect this effect [e.g. S. Benyoucef, A. Tounsi, S.A. Meftah, E.A. Adda Bedia, Compos. Interfaces, in press; S.T. Smith, J.G. Teng, Eng. Struct. 23 (7) (2001) 857-871; T.M. Roberts, Struct. Eng. 67 (12) (1989) 229-233; A. Tounsi, S. Benyoucef, Int. J. Adhes. Adhes., in press; T. Stratford, J. Cadei, Construct. Building Mater. 20 (2006) 34-35]. In addition, in the present study the anisotropic damage model is adopted to describe the damage of the RC beams. It is shown that the damage has a significant effect on the interfacial stresses in FRP-damaged RC beam

A new NASA LaRC Multi-Purpose Prepregging Unit

Science.gov (United States)

Wilkinson, S. P.; Marchello, J. M.; Dixon, D.; Johnston, N. J.

1993-01-01

A multi-purpose prepregging machine has been designed and built for NASA Langley Research Center. The machine has numerous advantages over existing units due to its various modular components. Each of these can be used individually or simultaneously depending on the required prepregging method. A reverse roll coater provides the ability to prepare thin films from typical hot-melt thermoset formulations. Also, if necessary, the design allows direct fiber impregnation within the reverse roll coater gap. Included in the impregnation module is a solution dip tank allowing the fabrication of thermoplastic prepregs from solution. The proceeding modules within the unit consist of four nip stations, two hot-plates, a hot-sled option and a high temperature oven. This paper describes the advantages of such a modular construction and discusses the various processing combinations available to the prepregger. A variety of high performance prepreg material systems were produced on IM7 (Hercules) carbon fiber. These included LaRC RP46, a PMR-type resin processed from methanol and two polyamide acids, LaRC IA and LaRC ITPI, prpregged from N-methyl pyrrolidinone (NMP). Parameters involved in the production of these prepreg materials are presented as are the mechanical properties of the resulting good quality laminates. A brief introduction into the existing prepregging science is presented. Topics relating to solution prepregging are identified with a focus on the current research effort and its future development.

The RC Circuit: An Approach with Fourier Transforms

Indian Academy of Sciences (India)

The RC Circuit: An Approach with Fourier Transforms. Classroom Volume 21 Issue 11 November 2016 pp 1029-1042 ... But a lot of things, (including the complex impedanceitself, and some insight into complex analysis) can be understoodbetter if we use the FT approach to solve the differentialequations that come up in ...

Hypomethylation of the IL17RC Promoter Associates with Age-Related Macular Degeneration

Directory of Open Access Journals (Sweden)

Lai Wei

2012-11-01

Full Text Available Age-related macular degeneration (AMD is the leading cause of irreversible blindness in the elderly population worldwide. Although recent studies have demonstrated strong genetic associations between AMD and SNPs in a number of genes, other modes of regulation are also likely to play a role in the etiology of this disease. We identified a significantly decreased level of methylation on the IL17RC promoter in AMD patients. Furthermore, we showed that hypomethylation of the IL17RC promoter in AMD patients led to an elevated expression of its protein and messenger RNA in peripheral blood as well as in the affected retina and choroid, suggesting that the DNA methylation pattern and expression of IL17RC may potentially serve as a biomarker for the diagnosis of AMD and likely plays a role in disease pathogenesis.

DISTRIBUTED RC NETWORKS WITH RATIONAL TRANSFER FUNCTIONS,

Science.gov (United States)

A distributed RC circuit analogous to a continuously tapped transmission line can be made to have a rational short-circuit transfer admittance and...one rational shortcircuit driving-point admittance. A subcircuit of the same structure has a rational open circuit transfer impedance and one rational ...open circuit driving-point impedance. Hence, rational transfer functions may be obtained while considering either generator impedance or load

A study on shear behavior of R/C beams subjected to long-term heating

International Nuclear Information System (INIS)

Maruta, M.; Yamazaki, M.

1993-01-01

In nuclear power plants, many structural members are subjected to long term heating. There are few experimental data available on the behavior especially in shear of reinforced concrete (R/C) members subjected to long term heating. This paper describes a study aimed at experimentally determining the shear behavior of R/C members in nuclear power plant facilities following sustained heating at high temperatures

Nonlinear analysis of RC cylindrical tank and subsoil accounting for a low concrete strength

Directory of Open Access Journals (Sweden)

Lewiński Paweł M.

2017-01-01

Full Text Available The paper discusses deformational and incremental approaches to a nonlinear FE analysis of soil-structure interaction including the description of behaviour of the RC structure and the subsoil under short-term loading. Two kinds of constitutive models for ground and structure were adopted for a nonlinear interaction analysis of the RC cylindrical tank with subsoil. The constitutive laws for concrete and subsoil were developed in compliance with the deformational and flow theories of plasticity. Moreover, a non-linear elastic-brittle-plastic analysis of RC axi-symmetric structures using finite element iterative techniques is presented. The results of the two types of FE analysis of soil-structure interaction are compared taking into account a low concrete strength of tank structure.

Compensability index for compensation radiotherapy after treatment interruptions

International Nuclear Information System (INIS)

Putora, Paul Martin; Schmuecking, Michael; Aebersold, Daniel; Plasswilm, Ludwig

2012-01-01

The goal of our work was to develop a simple method to evaluate a compensation treatment after unplanned treatment interruptions with respect to their tumour- and normal tissue effect. We developed a software tool in java programming language based on existing recommendations to compensate for treatment interruptions. In order to express and visualize the deviations from the originally planned tumour and normal tissue effects we defined the compensability index. The compensability index represents an evaluation of the suitability of compensatory radiotherapy in a single number based on the number of days used for compensation and the preference of preserving the originally planned tumour effect or not exceeding the originally planned normal tissue effect. An automated tool provides a method for quick evaluation of compensation treatments. The compensability index calculation may serve as a decision support system based on existing and established recommendations

A hybrid Rankine cycle (HyRC) with ambient pressure combustion (APC)

International Nuclear Information System (INIS)

Wu, Lijun; Thimsen, David; Clements, Bruce; Zheng, Ligang; Pomalis, Richard

2014-01-01

The main losses in thermal power generation include heat in exhaust flue gas, heat rejected through steam condensation of low-pressure turbine, and exergy destruction in heat exchange process etc. To the extent that the heat losses are significantly greater in temperature than either air or water coolant resources, these losses also represent exergy losses which might be exploited to improve plant capacity and efficiency. This paper presents a hybrid Rankine cycle (HyRC) with an ambient pressure combustion (APC) boiler to address the recovery potential of these losses within the steam Rankine cycle (SRC). The APC–HyRC concept employs an organic Rankine cycle (ORC) to supplement SRC and to reduce cycle energy losses to the atmosphere since organic fluids are capable of lowering cycle condensation temperature when a very low temperature heat sink is available. The case studies based on a 399 MW SRC unit show that the APC–HyRC configurations have better thermodynamic performance than its base case SRC at a cycle condensation temperature of 30 °C and below. The best APC–HyRC configuration generates up to 14% more power than the baseline steam cycle which is a 5.45% increase in overall gross efficiency with a cycle condensation temperature at 4 °C. - Highlights: • A hybrid Rankine cycle with water and organic fluid is presented. • Heat losses in exhaust flue gas and exhaust steam are reduced. • Exergy losses in regeneration process are reduced. • Efficiency improvements are made to the conventional steam Rankine cycle. • Issues in design/construction of greenfield and repowering project are discussed

Pitting corrosion and structural reliability of corroding RC structures: Experimental data and probabilistic analysis

International Nuclear Information System (INIS)

Stewart, Mark G.; Al-Harthy, Ali

2008-01-01

A stochastic analysis is developed to assess the temporal and spatial variability of pitting corrosion on the reliability of corroding reinforced concrete (RC) structures. The structure considered herein is a singly reinforced RC beam with Y16 or Y27 reinforcing bars. Experimental data obtained from corrosion tests are used to characterise the probability distribution of pit depth. The RC beam is discretised into a series of small elements and maximum pit depths are generated for each reinforcing steel bar in each element. The loss of cross-sectional area, reduction in yield strength and reduction in flexural resistance are then inferred. The analysis considers various member spans, loading ratios, bar diameters and numbers of bars in a given cross-section, and moment diagrams. It was found that the maximum corrosion loss in a reinforcing bar conditional on beam collapse was no more than 16%. The probabilities of failure considering spatial variability of pitting corrosion were up to 200% higher than probabilities of failure obtained from a non-spatial analysis after 50 years of corrosion. This shows the importance of considering spatial variability in a structural reliability analysis for deteriorating structures, particularly for corroding RC beams in flexure

The Tension-Stiffening Contribution of NSM CFRP to the Behavior of Strengthened RC Beams

Directory of Open Access Journals (Sweden)

Ahmad Azim Shukri

2015-07-01

Full Text Available Tension stiffening is a characteristic behavior of reinforced concrete (RC beams which is directly affected by the bond-slip property of steel bar and concrete interfaces. A beam strengthened with a near-surface mounted (NSM technique would be even more affected by tension stiffening, as the NSM reinforcement also possess a bond-slip property. Yet assessing how much the tension stiffening of NSM contributes to the behavior of RC beams is difficult due to the fact that bond-slip effects cannot be directly incorporated into a strain-based moment-curvature analysis. As such, the tension stiffening is typically incorporated through various empirical formulations, which can require a great deal of testing and calibrations to be done. In this paper a relatively new method, which can be called the mechanics-based segmental approach, is used to directly simulate the tension stiffening effect of NSM reinforcements on RC beams, without the need for empirical formulations to indirectly simulate the tension stiffening. Analysis shows that the tension stiffening of NSM fiber reinforced polymer (FRP contributes a significant portion to the stiffness and strength of the strengthened RC beam not only during serviceability, but at all load levels.

The Tension-Stiffening Contribution of NSM CFRP to the Behavior of Strengthened RC Beams.

Science.gov (United States)

Shukri, Ahmad Azim; Darain, Kh Mahfuz Ud; Jumaat, Mohd Zamin

2015-07-08

Tension stiffening is a characteristic behavior of reinforced concrete (RC) beams which is directly affected by the bond-slip property of steel bar and concrete interfaces. A beam strengthened with a near-surface mounted (NSM) technique would be even more affected by tension stiffening, as the NSM reinforcement also possess a bond-slip property. Yet assessing how much the tension stiffening of NSM contributes to the behavior of RC beams is difficult due to the fact that bond-slip effects cannot be directly incorporated into a strain-based moment-curvature analysis. As such, the tension stiffening is typically incorporated through various empirical formulations, which can require a great deal of testing and calibrations to be done. In this paper a relatively new method, which can be called the mechanics-based segmental approach, is used to directly simulate the tension stiffening effect of NSM reinforcements on RC beams, without the need for empirical formulations to indirectly simulate the tension stiffening. Analysis shows that the tension stiffening of NSM fiber reinforced polymer (FRP) contributes a significant portion to the stiffness and strength of the strengthened RC beam not only during serviceability, but at all load levels.

Compensability index for compensation radiotherapy after treatment interruptions

Directory of Open Access Journals (Sweden)

Putora Paul

2012-12-01

Full Text Available Abstract Background The goal of our work was to develop a simple method to evaluate a compensation treatment after unplanned treatment interruptions with respect to their tumour- and normal tissue effect. Methods We developed a software tool in java programming language based on existing recommendations to compensate for treatment interruptions. In order to express and visualize the deviations from the originally planned tumour and normal tissue effects we defined the compensability index. Results The compensability index represents an evaluation of the suitability of compensatory radiotherapy in a single number based on the number of days used for compensation and the preference of preserving the originally planned tumour effect or not exceeding the originally planned normal tissue effect. An automated tool provides a method for quick evaluation of compensation treatments. Conclusions The compensability index calculation may serve as a decision support system based on existing and established recommendations.

Damage Localization and Quantification of Earthquake Excited RC-Frames

DEFF Research Database (Denmark)

Skjærbæk, P.S.; Nielsen, Søren R.K.; Kirkegaard, Poul Henning

In the paper a recently proposed method for damage localization and quantification of RC-structures from response measurements is tested on experimental data. The method investigated requires at least one response measurement along the structure and the ground surface acceleration. Further, the t...

Numerical model of RC beam response to corrosion

Science.gov (United States)

German, Magdalena; Pamin, Jerzy

2018-01-01

The chloride-induced corrosion of reinforcement used to be represented by Tuutti's model with initiation and propagation phases. During the initiation phase chlorides penetrate the concrete cover and accumulate around reinforcement bars. The chloride concentration in concrete increases until it reaches a chloride threshold value, causing deterioration of the passive layer of reinforcement. Then the propagation phase begins. During the propagation phase steel has no natural anti-corrosion protection, a corrosion current flows and this induces the production of rust. A growing volume of corrosion products generates stresses in concrete, which leads to cracking, splitting, delamination and loss of strength. The mechanical response of RC elements to reinforcement corrosion has mostly been examined on the basis of a 2D cross-section analysis. However, with this approach it is not possible to represent both corrosion and static loading. In the paper a 3D finite element model of an RC beam with the two actions applied is presented. Rust is represented as an interface between steel and concrete, considering the volumetric expansion of rust.

Impact response of RC rock-shed girder with sand cushion under falling load

International Nuclear Information System (INIS)

Bhatti, Abdul Qadir; Kishi, Norimitsu

2010-01-01

Research highlights: → An applicability of FE model of RC girders with sand cushion has been investigated. → Experimental and numerical results of Impact force, reaction force and displacement have been performed. → Cracks obtained from numerical models are in good agreement with the experimental ones. → Reaction force-displacement loops agree well between numerical and experimental results. → The configuration of the hysteretic loop at failure of RC girders can be approximated by a parallelogram. - Abstract: In order to establish a proper finite element model of prototype RC girder with sand element for impact response analysis, dynamic response analysis of RC girders with sand cushion subjected to impact force due to weight falling from the height of H = 2.5, 5, 7.5 and 10 m was performed to improve the state of the art of protective design for real scale rock-sheds by using LS-DYNA code. An applicability of proposed model was discussed comparing with experimental results (e.g. impact force, reaction force and displacement waves). From this study, dynamic characteristics of impact response can be better simulated by using the proposed model. As a result, when the sand cushion was set up, the impact force, reaction force, mid-span displacement waves, distribution of reaction force-displacement loops, and crack patterns obtained from the numerical analysis are in good agreement with those from the experimental results.

Experimental study on behavior of RC panels covered with steel plates subjected to missile impact

International Nuclear Information System (INIS)

Jun Hashimoto; Katsuki Takiguchi; Koshiro Nishimura; Kazuyuki Matsuzawa; Mayuko Tsutsui; Yasuhiro Ohashi; Isao Kojima; Haruhiko Torita

2005-01-01

This paper describes an experimental study on the behavior of concrete panels with steel plate subjected to missile impact. Two tests were carried out, divided in accordance with the types of projectile, non-deformable and deformable. In all, 40 specimens of 750 mm square were prepared. The panel specimen was suspended vertically by two steel wire ropes to allow free movement after projectile impact, and was subjected to a projectile. As a result, it is confirmed that a RC panel with steel plate on its back side has higher impact resistance performance than a RC panel and that thickness of concrete panel, thickness of steel plate and the impact velocity of the projectile have a great effect on the failure modes of steel concrete panels. Moreover, based on the experimental results, the quantitative evaluation method for impact resistance performance of RC panels covered with steel plates is examined. The formula for perforation velocity of a half steel concrete panel, proposed in accordance with the bulging height, is effective to evaluate the impact resistance performance of RC panels with steel plates. (authors)

Single-stage plasma-based correlated energy spread compensation for ultrahigh 6D brightness electron beams

Science.gov (United States)

Manahan, G. G.; Habib, A. F.; Scherkl, P.; Delinikolas, P.; Beaton, A.; Knetsch, A.; Karger, O.; Wittig, G.; Heinemann, T.; Sheng, Z. M.; Cary, J. R.; Bruhwiler, D. L.; Rosenzweig, J. B.; Hidding, B.

2017-06-01

Plasma photocathode wakefield acceleration combines energy gains of tens of GeV m-1 with generation of ultralow emittance electron bunches, and opens a path towards 5D-brightness orders of magnitude larger than state-of-the-art. This holds great promise for compact accelerator building blocks and advanced light sources. However, an intrinsic by-product of the enormous electric field gradients inherent to plasma accelerators is substantial correlated energy spread--an obstacle for key applications such as free-electron-lasers. Here we show that by releasing an additional tailored escort electron beam at a later phase of the acceleration, when the witness bunch is relativistically stable, the plasma wave can be locally overloaded without compromising the witness bunch normalized emittance. This reverses the effective accelerating gradient, and counter-rotates the accumulated negative longitudinal phase space chirp of the witness bunch. Thereby, the energy spread is reduced by an order of magnitude, thus enabling the production of ultrahigh 6D-brightness beams.

Biochemical and Molecular Characterization of RcSUS1, a Cytosolic Sucrose Synthase Phosphorylated in Vivo at Serine 11 in Developing Castor Oil Seeds*

Science.gov (United States)

Fedosejevs, Eric T.; Ying, Sheng; Park, Joonho; Anderson, Erin M.; Mullen, Robert T.; She, Yi-Min; Plaxton, William C.

2014-01-01

Sucrose synthase (SUS) catalyzes the UDP-dependent cleavage of sucrose into UDP-glucose and fructose and has become an important target for improving seed crops via metabolic engineering. A UDP-specific SUS homotetramer composed of 93-kDa subunits was purified to homogeneity from the triacylglyceride-rich endosperm of developing castor oil seeds (COS) and identified as RcSUS1 by mass spectrometry. RcSUS1 transcripts peaked during early development, whereas levels of SUS activity and immunoreactive 93-kDa SUS polypeptides maximized during mid-development, becoming undetectable in fully mature COS. The cytosolic location of the enzyme was established following transient expression of RcSUS1-enhanced YFP in tobacco suspension cells and fluorescence microscopy. Immunological studies using anti-phosphosite-specific antibodies revealed dynamic and high stoichiometric in vivo phosphorylation of RcSUS1 at its conserved Ser-11 residue during COS development. Incorporation of 32Pi from [γ-32P]ATP into a RcSUS1 peptide substrate, alongside a phosphosite-specific ELISA assay, established the presence of calcium-dependent RcSUS1 (Ser-11) kinase activity. Approximately 10% of RcSUS1 was associated with COS microsomal membranes and was hypophosphorylated relative to the remainder of RcSUS1 that partitioned into the soluble, cytosolic fraction. Elimination of sucrose supply caused by excision of intact pods of developing COS abolished RcSUS1 transcription while triggering the progressive dephosphorylation of RcSUS1 in planta. This did not influence the proportion of RcSUS1 associated with microsomal membranes but instead correlated with a subsequent marked decline in SUS activity and immunoreactive RcSUS1 polypeptides. Phosphorylation at Ser-11 appears to protect RcSUS1 from proteolysis, rather than influence its kinetic properties or partitioning between the soluble cytosol and microsomal membranes. PMID:25313400

Seismic performance of masonry-infilled RC frames

Directory of Open Access Journals (Sweden)

Mircea Bârnaure

2016-09-01

Full Text Available The masonry infill of RC frames structures is generally considered as non-structural. The design of the concrete frames is often made by ignoring the influence of the masonry infill, which is only accounted for its mass. The experience on buildings submitted to earthquakes shows that masonry infill walls completely change the behaviour of bare frames due to increased initial stiffness and low deformability. The way in which masonry infills affect the RC frames members is difficult to predict, as different failure modes can occur either in the masonry or in the surrounding frame. In addition to local effects, the position of the masonry infills at different levels can lead to structural irregularity, with a strong influence on the global seismic response of the building. Less infilled stories, also called soft stories, have a particularly unfavourable behaviour under seismic loads, as frame members at these levels are more susceptible to failure. This paper analyses the differences in the behaviour of bare and infilled frames through numerical modelling. Nonlinear push-over analyses of infilled frames are carried out under in-plane vertical and lateral loading. The infill panels are modelled as equivalent single diagonal struts. Several force-displacements laws are considered for these diagonals.

Comparative Analysis of Existing RC Columns Jacketed with CFRP or FRCC

Directory of Open Access Journals (Sweden)

Marta Del Zoppo

2018-03-01

Full Text Available Reinforced concrete (RC columns typical of existing structures often exhibit premature failures during seismic events (i.e., longitudinal bars buckling and shear interaction mechanisms due to the poor quality concrete and the absence of proper seismic details in the potential plastic hinge region. The Fiber Reinforced Polymers (FRP externally bonded reinforcement is known to be a valid technique to improve the shear capacity or the ductility of existing RC columns. However, few experimental tests have proven its effectiveness in the case of columns affected by shear interaction mechanisms. In this work, the behavior of existing RC columns with border line behavior between flexure and shear have been investigated in the case of poor quality concrete and light FRP strengthening with local jacketing and medium quality concrete and strong FRP strengthening with local jacketing, in order to highlight the effect of concrete strength on the effectiveness of the retrofit intervention. As an alternative to FRP jacketing; the effectiveness of the Fiber Reinforced Cementitious Composite (FRCC jacketing for the seismic strengthening of columns with highly deteriorated concrete cover or columns already damaged by an earthquake is also evaluated. Six full-scale RC columns have been tested under cyclic loading: one was used as a control specimen; four were strengthened in the potential plastic hinge region with carbon FRP (CFRP; and one was fully jacketed with FRCC. The comparison between poor and medium quality concrete columns showed that the CFRP local jacketing is more effective in the case of poor quality concrete. The FRCC jacketing appears to be a sound repair strategy and a suitable alternative to the FRP jacketing in case of poor quality; however, more experimental research is needed for improving this retrofit technique.

KOMBINASI ALGORITMA AES, RC4 DAN ELGAMAL DALAM SKEMA HYBRID UNTUK KEAMANAN DATA

Directory of Open Access Journals (Sweden)

Adi Widarma

2016-01-01

Full Text Available Pengiriman atau pertukaran data adalah hal yang sering terjadi dalam dunia teknologi informasi. Data yang dikirim kadang sering berisi data informasi yang penting bahkan sangat rahasia dan harus dijaga keamanannya. Untuk menjaga keamanan data, dapat dilakukan dengan menggunakan teknik kriptografi. Algoritma AES dan RC4 adalah salah satu dari algoritma simetri. Kelemahan dari algoritma simetri adalah proses enkripsi dan dekripsi menggunakan kunci yang sama. Untuk mengatasi tersebut dilakukan dengan menggunakan algoritma Elgamal. Algoritma Elgamal adalah termasuk algoritma asimetri. Algoritma Elgamal digunakan untuk mengamankan kunci dari algoritma AES dan RC4. Peningkatan keamanan pesan dan kunci dilakukan dengan algoritma hybrid. Algoritma hybrid dengan mengkombinasikan beberapa algoritma baik algoritma simetri maupun algortima asimetri akan menambah keamanan sehingga menjadi lebih aman dan powerful (Jain & Agrawal 2014. Penelitian ini akan dilakukan metode hybrid yaitu mengkombinasikan beberapa algoritma kriptografi dengan menggunakan algoritma Advanced Encryption Standard (AES dan RC4 untuk kerahasiaan data serta algoritma Elgamal digunakan untuk enkripsi dan dekripsi kunci.

CD45RC isoform expression identifies functionally distinct T cell subsets differentially distributed between healthy individuals and AAV patients.

Directory of Open Access Journals (Sweden)

Laurence Ordonez

Full Text Available In animal models of anti-neutrophil cytoplasmic antibody (ANCA-associated vasculitis (AAV, the proportion of CD45RC T cell subsets is important for disease susceptibility. Their human counterparts are, however, functionally ill defined. In this report, we studied their distribution in healthy controls (HC, AAV patients and in Systemic lupus erythematous (SLE patients as disease controls. We showed that CD45RC expression level on human CD4 and CD8 T cells identifies subsets that are highly variable among individuals. Interestingly, AAV patients exhibit an increased proportion of CD45RC(low CD4 T cells as compared to HC and SLE patients. This increase is stable over time and independent of AAV subtype, ANCA specificity, disease duration, or number of relapses. We also analyzed the cytokine profile of purified CD4 and CD8 CD45RC T cell subsets from HC, after stimulation with anti-CD3 and anti-CD28 mAbs. The CD45RC subsets exhibit different cytokine profiles. Type-1 cytokines (IL-2, IFN-gamma and TNF-alpha were produced by all CD45RC T cell subsets, while the production of IL-17, type-2 (IL-4, IL-5 and regulatory (IL-10 cytokines was restricted to the CD45RC(low subset. In conclusion, we have shown that CD45RC expression divides human T cells in functionally distinct subsets that are imbalanced in AAV. Since this imbalance is stable over time and independent of several disease parameters, we hypothesize that this is a pre-existing immune abnormality involved in the etiology of AAV.

Derivation of the point spread function for zero-crossing-demodulated position-sensitive detectors

International Nuclear Information System (INIS)

Nowlin, C.H.

1976-07-01

This work is a mathematical derivation of a high-quality approximation to the point spread function for position-sensitive detectors (PSDs) that use pulse-shape modulation and crossover-time demodulation. The approximation is determined as a general function of the input signals to the crossover detectors so as to enable later determination of optimum position-decoding filters for PSDs. This work is precisely applicable to PSDs that use either RC or LC transmission line encoders. The effects of random variables, such as charge collection time, in the encoding process are included. In addition, this work presents a new, rigorous method for the determination of upper and lower bounds for conditional crossover-time distribution functions (closely related to first-passage-time distribution functions) for arbitrary signals and arbitrary noise covariance functions

RC-3095, a Selective Gastrin-Releasing Peptide Receptor Antagonist, Does Not Protect the Lungs in an Experimental Model of Lung Ischemia-Reperfusion Injury

Directory of Open Access Journals (Sweden)

Vera L. Oliveira-Freitas

2015-01-01

Full Text Available RC-3095, a selective GRPR antagonist, has been shown to have anti-inflammatory properties in different models of inflammation. However, its protective effect on lungs submitted to lung ischemia-reperfusion injury has not been addressed before. Then, we administrated RC-3095 intravenously before and after lung reperfusion using an animal model of lung ischemia-reperfusion injury (LIRI by clamping the pulmonary hilum. Twenty Wistar rats were subjected to an experimental model in four groups: SHAM, ischemia-reperfusion (IR, RC-Pre, and RC-Post. The final mean arterial pressure significantly decreased in IR and RC-Pre compared to their values before reperfusion (P<0.001. The RC-Post group showed significant decrease of partial pressure of arterial oxygen at the end of the observation when compared to baseline (P=0.005. Caspase-9 activity was significantly higher in the RC-Post as compared to the other groups (P<0.013. No significant differences were observed in eNOS activity among the groups. The groups RC-Pre and RC-Post did not show any significant decrease in IL-1β (P=0.159 and TNF-α (P=0.260, as compared to IR. The histological score showed no significant differences among the groups. In conclusion, RC-3095 does not demonstrate a protective effect in our LIRI model. Additionally, its use after reperfusion seems to potentiate cell damage, stimulating apoptosis.

nRC: non-coding RNA Classifier based on structural features.

Science.gov (United States)

Fiannaca, Antonino; La Rosa, Massimo; La Paglia, Laura; Rizzo, Riccardo; Urso, Alfonso

2017-01-01

Non-coding RNA (ncRNA) are small non-coding sequences involved in gene expression regulation of many biological processes and diseases. The recent discovery of a large set of different ncRNAs with biologically relevant roles has opened the way to develop methods able to discriminate between the different ncRNA classes. Moreover, the lack of knowledge about the complete mechanisms in regulative processes, together with the development of high-throughput technologies, has required the help of bioinformatics tools in addressing biologists and clinicians with a deeper comprehension of the functional roles of ncRNAs. In this work, we introduce a new ncRNA classification tool, nRC (non-coding RNA Classifier). Our approach is based on features extraction from the ncRNA secondary structure together with a supervised classification algorithm implementing a deep learning architecture based on convolutional neural networks. We tested our approach for the classification of 13 different ncRNA classes. We obtained classification scores, using the most common statistical measures. In particular, we reach an accuracy and sensitivity score of about 74%. The proposed method outperforms other similar classification methods based on secondary structure features and machine learning algorithms, including the RNAcon tool that, to date, is the reference classifier. nRC tool is freely available as a docker image at https://hub.docker.com/r/tblab/nrc/. The source code of nRC tool is also available at https://github.com/IcarPA-TBlab/nrc.

Problems and their solutions in practical application of Eurocodes in seismic design of RC structures

Directory of Open Access Journals (Sweden)

Milev Jordan

2016-01-01

Full Text Available The main purpose of the paper is to present practical application of Eurocodes in the field of RC structures design. The selected examples represent the main problems in practical application of Eurocodes for seismic analysis and design of RC Structures in Bulgarian construction practice. The analysis is focused on some structural and economic problems as well as on some contradictions in Eurocode 8 itself. Special attention is paid to the practical solution of the following problems: recognition of torsionally flexible systems, stiffness reduction of RC elements for linear analysis dimensions and detailing of confined boundary areas of shear walls, detailing of wall structures, etc. Those problems appear during the practical design of some buildings in Bulgaria. Several proposals for solving some problems defined in the paper are presented through some practical examples. Some conclusions are made for further application of Eurocode 8 in the design and construction practice. The importance of some rules and procedures in Eurocode 8 is supported by the examples of damaged RC members during the past earthquakes. The problems of Eurocode 8 and their solutions are illustrated through the experience of Bulgarian construction practice.

Study on shear strengthening of RC continuous T-beams using different layers of CFRP strips

Energy Technology Data Exchange (ETDEWEB)

Alferjani, M. B. S.; Samad, A. A. Abdul; Mohamad, Noridah [Faculty of Civil and Environmental Engineering, Universiti Tun Hussein Onn Malaysia, Batu Pahat (Malaysia); Elrawaff, Blkasem S.; Elzaroug, Omer [Faculty of Civil Engineering Omar Al Mukhtar University, Bayda, Libya, Africa (Libya)

2015-05-15

Carbon fiber reinforced polymer (CFRP) laminates are externally bonded to reinforced concrete (RC) members to provide additional strength such as flexural, shear, etc. However, this paper presents the results of an experimental investigation for enhancing the shear capacity of reinforced concrete (RC) continuous T- beams using different layers of CFRP wrapping schemes. A total of three concrete beams were tested and various sheet configurations and layouts were studied to determine their effects on ultimate shear strength and shear capacity of the beams. One beam was kept as control beams, while other beams were strengthened with externally bonded CFRP strips with three side bonding and one or two layers of CFRP strips. From the test results, it was found that all schemes were found to be effective in enhancing the shear strength of RC beams. It was observed that the strength increases with the number of sheet layers provided the most effective strengthening for RC continuous T- beam. Beam strengthened using this scheme showed 23.21% increase in shear capacity as compared to the control beam. Two prediction models available in literature were used for computing the contribution of CFRP strips and compared with the experimental results.

TIGER: Development of Thermal Gradient Compensation Algorithms and Techniques

Science.gov (United States)

Hereford, James; Parker, Peter A.; Rhew, Ray D.

2004-01-01

In a wind tunnel facility, the direct measurement of forces and moments induced on the model are performed by a force measurement balance. The measurement balance is a precision-machined device that has strain gages at strategic locations to measure the strain (i.e., deformations) due to applied forces and moments. The strain gages convert the strain (and hence the applied force) to an electrical voltage that is measured by external instruments. To address the problem of thermal gradients on the force measurement balance NASA-LaRC has initiated a research program called TIGER - Thermally-Induced Gradients Effects Research. The ultimate goals of the TIGER program are to: (a) understand the physics of the thermally-induced strain and its subsequent impact on load measurements and (b) develop a robust thermal gradient compensation technique. This paper will discuss the impact of thermal gradients on force measurement balances, specific aspects of the TIGER program (the design of a special-purpose balance, data acquisition and data analysis challenges), and give an overall summary.

Summary of LaRC 2-inch Erectable Joint Hardware Heritage Test Data

Science.gov (United States)

Dorsey, John T.; Watson, Judith J.

2016-01-01

As the National Space Transportation System (STS, also known as the Space Shuttle) went into service during the early 1980's, NASA envisioned many missions of exploration and discovery that could take advantage of the STS capabilities. These missions included: large orbiting space stations, large space science telescopes and large spacecraft for manned missions to the Moon and Mars. The missions required structures that were significantly larger than the payload volume available on the STS. NASA Langley Research Center (LaRC) conducted studies to design and develop the technology needed to assemble the large space structures in orbit. LaRC focused on technology for erectable truss structures, in particular, the joint that connects the truss struts at the truss nodes. When the NASA research in large erectable space structures ended in the early 1990's, a significant amount of structural testing had been performed on the LaRC 2-inch erectable joint that was never published. An extensive set of historical information and data has been reviewed and the joint structural testing results from this historical data are compiled and summarized in this report.

Numerical investigation of transient beam loading compensation in JLC X-band main linac

International Nuclear Information System (INIS)

Syrachev, I.V.; Higo, T.

1996-06-01

In the present paper, two methods, 'staggered timing' and 'RF modulation', were studied for the transient beam loading compensation in the JLC X-band main linac. The inter bunch energy spread was found to be easily reduced down to less than ±0.06% with 10 sets of injection timings along the linac in the former case while with a simple linear ramping of the input RF voltage in the latter case. For both cases the energy transfer efficiencies from the power source to the beam were exactly the same. The tolerance of the beam intensity jitter was found to be ±1% for the multibunch energy spread of ±0.1%. (author)

Behavior of Insulated Carbon-FRP-Strengthened RC Beams Exposed to Fire

Science.gov (United States)

Sayin, B.

2014-09-01

There are two main approaches to improving the fire resistance of fiber-reinforced polymer (FRP) systems. While the most common method is to protect or insulate the FRP system, an other way is to use fibers and resins with a better fire performance. This paper presents a numerical investigation into the five protection behavior of insulated carbon-fiber-reinforced-polymer (CFRP)-strengthened reinforced concrete (RC) beams. The effects of external loading and thermal expansion of materials at elevated temperatures are taken into consideration in a finite-element model. The validity of the numerical model is demonstrated with results from an existing experimental study on insulated CFRP-strengthened RC beams. Conclusions of this investigation are employed to predict the structural behavior of CFRP-strengthened concrete structures.

Analysis of an Irregular RC Multi-storeyed Building Subjected to Dynamic Loading

Science.gov (United States)

AkashRaut; Pachpor, Prabodh; Dautkhani, Sanket

2018-03-01

Many buildings in the present scenario have irregular configurations both in plan and elevation. This in future may subject to devastating earthquakes. So it is necessary to analyze the structure. The present paper is made to study three type of irregularity wiz vertical, mass and plan irregularity as per clause 7.1 of IS 1893 (part1)2002 code. The paper discusses the analysis of RC (Reinforced Concrete) Buildings with vertical irregularity. The study as a whole makes an effort to evaluate the effect of vertical irregularity on RC buildings for which comparison of three parameters namely shear force, bending moment and deflection are taken into account.

Structural model and excitonic properties of the dimeric RC-LH1-PufX complex from Rhodobacter sphaeroides

International Nuclear Information System (INIS)

Sener, Melih; Hsin, Jen; Trabuco, Leonardo G.; Villa, Elizabeth; Qian, Pu; Hunter, C. Neil; Schulten, Klaus

2009-01-01

The light-harvesting apparatus of the purple bacterial photosynthetic unit consists of a pool of peripheral light-harvesting complexes that transfer excitation energy to a reaction center (RC) via the surrounding pigment-protein complex LH1. Recent electron microscopy and atomic force microscopy studies have revealed that RC-LH1 units of Rhodobacter (Rba.) sphaeroides form membrane-bending dimeric complexes together with the polypeptide PufX. We present a structural model for these RC-LH1-PufX dimeric complexes constructed using the molecular dynamics flexible fitting method based on an EM density map. The arrangement of the LH1 BChls displays a distortion near the proposed location of the PufX polypeptide. The resulting atomic model for BChl arrays is used to compute the excitonic properties of the dimeric RC-LH1 complex. A comparison is presented between the structural and excitonic features of the S-shaped dimeric BChl array of Rba. sphaeroides and the circular BChl arrangement found in other purple bacteria

Experimental investigations on a cascaded steam-/organic-Rankine-cycle (RC/ORC) system for waste heat recovery (WHR) from diesel engine

International Nuclear Information System (INIS)

Yu, Guopeng; Shu, Gequn; Tian, Hua; Huo, Yongzhan; Zhu, Weijie

2016-01-01

Highlights: • A novel cascaded RC/ORC system was constructed for WHR of a heavy-duty diesel engine. • The RC/ORC system was experimentally investigated under engine operating conditions. • Good system stability and satisfying thermal states of working fluids were observed. • The power increment can reach up to 5.6% by equipping the novel cascaded RC/ORC system. - Abstract: A novel cascaded RC/ORC system that comprises a steam Rankine cycle as the high-temperature loop (H-RC) and an organic Rankine cycle as the low-temperature loop (L-ORC) was constructed and experimentally investigated to recover waste heat from exhaust gas of a heavy-duty diesel engine (DE). By monitoring key parameters of the RC/ORC system against time, good system stability and satisfying thermal states of working fluids were observed. Impacts that the engine operations have on this proposed waste-heat-recovery (WHR) system were studied, indicating that waste heat recovered from the gas increases gradually and greatly as the engine load increases, yet decreases slightly as the speed grows. At full loads at speeds lower than 2050 rpm, up to 101.5 kW of waste heat can be abstracted from the gas source, showing a promising heat transfer potential. Besides, observations of key exergy states as well as estimations and comparisons of potential output power were carried out stepwise. Results indicated that up to 12.7 kW of output power could be obtained by the novel RC/ORC system under practical estimations. Comparing to the basic diesel engine, the power increment reaches up to 5.6% by equipping the cascaded RC/ORC system.

Pros and cons of multistory RC tunnel-form (box-type) buildings

Science.gov (United States)

Kalkan, E.; Yuksel, S.B.

2008-01-01

Tunnel-form structural systems (i.e., box systems), having a load-carrying mechanism composed of reinforced concrete (RC) shear walls and slabs only, have been prevailingly utilized in the construction of multistory residential units. The superiority of tunnel-form buildings over their conventional counterparts stems from the enhanced earthquake resistance they provide, and the considerable speed and economy of their construction. During recent earthquakes in Turkey, they exhibited better seismic performance in contrast to the damaged condition of a number of RC frames and dual systems (i.e., RC frames with shear wall configurations). Thus the tunnel-form system has become a primary construction technique in many seismically active regions. In this paper, the strengths and weaknesses of tunnel-form buildings are addressed in terms of design considerations and construction applications. The impacts of shear wall reinforcement ratio and its detailing on system ductility, loadcarrying capacity and failure mechanism under seismic forces are evaluated at section and global system levels. Influences of tension/compression coupling and wall openings on the response are also discussed. Three-dimensional nonlinear finite element models, verified through comparisons with experimental results, were used for numerical assessments. Findings from this projection provide useful information on adequate vertical reinforcement ratio and boundary reinforcement to achieve enhanced performance of tunnel-form buildings under seismic actions. Copyright ?? 2007 John Wiley & Sons, Ltd.

Losses compensation; Compensation des pertes

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

One mission of RTE (Electric Power Transportation), is to watch over the losses compensation resulting from the power transport on the electric power network. Since january 2001, RTE makes good the electric losses by the purchase of energy. To choose the marketers, a consultation has been realized by RTE. This document presents the rules concerning these losses compensation. (A.L.B.)

The gammaTuRC Nanomachine Mechanism and Future Applications

Science.gov (United States)

Riehlman, Timothy D.

The complexity and precision of the eukaryotic cell's cytoskeletal network is unrivaled by any man-made systems, perfected by billions of years of evolution, mastering elegant processes of self-assembly, error correction, and self-repair. Understanding the capabilities of these networks will have important and far reaching applications in human medicine by aiding our understanding of developmental processes, cellular division, and disease mechanisms, and through biomimicry will provide insights for biosynthetic manufacturing at the nanoscale and across scales. My research utilizes cross species techniques from Human to the model organism of Fission Yeast to investigate the structure and mechanisms of the g-tubulin ring complex (gTuRC). The gTuRC is a highly conserved eukaryotic multiprotein complex serving as a microtubule organizing center (MTOC) responsible for microtubule nucleation through templating, regulation of dynamics, and establishment of microtubule polarity. Microtubules are 25 nm diameter dynamic flexible polymers of a/b-tubulin heterodimers that function as scaffolds, force generators, distributors, and intracellular highways. The microtubule cytoskeleton is essential for numerous fundamental cellular processes such as mitotic division of chromosomes and cell division, organelle distribution within the cell, cell signaling, and cell shape. This incredible diversity in functions is made possible in part due to molecular motor Kinesin-like proteins (Klps), which allow expansion into more specialized neural, immune, and ciliated cell functions. Combined, the MTOC, microtubules, and Klps represent ideal microtubule cytoskeleton protein (MCP) modular components for in vitro biomimicry towards generation of adaptable patterned networks for human designed applications. My research investigates the hypothesis that a mechanistic understanding of conserved MTOC gTuRC mechanisms will help us understand dynamic cellular nanomachines and their ability to self

High-Affinity Sites Form an Interaction Network to Facilitate Spreading of the MSL Complex across the X Chromosome in Drosophila

NARCIS (Netherlands)

Ramírez, Fidel; Lingg, Thomas; Toscano, Sarah; Lam, Kin Chung; Georgiev, Plamen; Chung, Ho-Ryun; Lajoie, Bryan R; de Wit, Elzo; Zhan, Ye; de Laat, Wouter; Dekker, Job; Manke, Thomas; Akhtar, Asifa

2015-01-01

Dosage compensation mechanisms provide a paradigm to study the contribution of chromosomal conformation toward targeting and spreading of epigenetic regulators over a specific chromosome. By using Hi-C and 4C analyses, we show that high-affinity sites (HAS), landing platforms of the male-specific

Prediction of the Fundamental Period of Infilled RC Frame Structures Using Artificial Neural Networks

Directory of Open Access Journals (Sweden)

Panagiotis G. Asteris

2016-01-01

Full Text Available The fundamental period is one of the most critical parameters for the seismic design of structures. There are several literature approaches for its estimation which often conflict with each other, making their use questionable. Furthermore, the majority of these approaches do not take into account the presence of infill walls into the structure despite the fact that infill walls increase the stiffness and mass of structure leading to significant changes in the fundamental period. In the present paper, artificial neural networks (ANNs are used to predict the fundamental period of infilled reinforced concrete (RC structures. For the training and the validation of the ANN, a large data set is used based on a detailed investigation of the parameters that affect the fundamental period of RC structures. The comparison of the predicted values with analytical ones indicates the potential of using ANNs for the prediction of the fundamental period of infilled RC frame structures taking into account the crucial parameters that influence its value.

Tomographic reconstruction of storm time RC ion distribution from ENA images on board multiple spacecraft

Science.gov (United States)

Ma, Shu-Ying; Yan, Wei-Nan; Xu, Liang

2015-11-01

A quantitative retrieval of 3-D distribution of energetic ions as energetic neutral atoms (ENA) sources is a challenging task. In this paper the voxel computerized tomography (CT) method is initially applied to reconstruct the 3-D distribution of energetic ions in the magnetospheric ring current (RC) region from ENA emission images on board multiple spacecraft. To weaken the influence of low-altitude emission (LAE) on the reconstruction, the LAE-associated ENA intensities are corrected by invoking the thick-target approximation. To overcome the divergence in iteration due to discordant instrument biases, a differential ENA voxel CT method is developed. The method is proved reliable and advantageous by numerical simulation for the case of constant bias independent of viewing angle. Then this method is implemented with ENA data measured by the Two Wide-angle Imaging Neutral-atom Spectrometers mission which performs stereoscopic ENA imaging. The 3-D spatial distributions and energy spectra of RC ion flux intensity are reconstructed for energies of 4-50 keV during the main phase of a major magnetic storm. The retrieved ion flux distributions seem to correspond to an asymmetric partial RC, located mainly around midnight favoring the postmidnight with L = 3.5-7.0 in the equatorial plane. The RC ion distributions with magnetic local time depend on energy, with major equatorial flux peak for lower energy located east of that for higher energy. In comparison with the ion energy spectra measured by Time History of Events and Macroscale Interactions during Substorms-D satellite flying in the RC region, the retrieved spectrum from remotely sensed ENA images are well matched with the in situ measurements.

RC structures strengthened by metal shear panels: experimental and numerical analysis

International Nuclear Information System (INIS)

De Matteis, G.; Formisano, A.; Mazzolani, F. M.

2008-01-01

Metal shear panels (MSPs) may be effectively used as a lateral load resisting system for framed structures. In the present paper, such a technique is applied for the seismic protection of existing RC buildings, by setting up a specific design procedure, which has been developed on the basis of preliminary full-scale experimental tests. The obtained results allowed the development of both simplified and advanced numerical models of both the upgraded structure and the applied shear panels. Also, the proposed design methodology, which is framed in the performance base design philosophy, has been implemented for the structural upgrading of a real Greek existing multi-storey RC building. The results of the numerical analysis confirmed the effectiveness of the proposed technique, also emphasising the efficiency of the implemented design methodology

Creative compensation

International Nuclear Information System (INIS)

Coll, D.

1994-01-01

A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs

Creative compensation

Energy Technology Data Exchange (ETDEWEB)

Coll, D

1994-09-19

A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs.

Strengthening of RC bridge slabs using CFRP sheets

Directory of Open Access Journals (Sweden)

Fahmy A. Fathelbab

2014-12-01

Full Text Available Many old structures became structurally insufficient to carry the new loading conditions requirements. Moreover, they suffer from structural degradation, reinforcement steel bars corrosion, bad weather conditions…etc. Many official authorities in several countries had recognized many old bridges and buildings as structurally deficient by today’s standards. Due to these reasons, structural strengthening became an essential requirement and different strengthening techniques appeared in market. Fiber Reinforced Polymer (FRP strengthening techniques established a good position among all other techniques, giving excellent structural results, low time required and moderate cost compared with the other techniques. The main purpose of this research is to study analytically the strengthening of a reinforced concrete bridge slabs due to excessive loads, using externally bonded FRP sheets technique. A commercial finite element program ANSYS was used to perform a structural linear and non-linear analysis for strengthened slab models using several schemes of FRP sheets. A parametric study was performed to evaluate analytically the effect of changing both FRP stiffness and FRP schemes in strengthening RC slabs. Comparing the results with control slab (reinforced concrete slab without strengthening it is obvious that attaching FRP sheets to the RC slab increases its capacity and enhances the ductility/toughness.

Semi-Active Control of Precast RC Columns under Seismic Action

Science.gov (United States)

Caterino, Nicola; Spizzuoco, Mariacristina

2017-10-01

This work is inspired by the idea of dissipating seismic energy at the base of prefabricated RC columns via semi-active (SA) variable dampers exploiting the base rocking. It was performed a wide numerical campaign to investigate the seismic behaviour of a pre-cast RC column with a variable base restraint. The latter is based on the combined use of a hinge, elastic springs, and magnetorheological (MR) dampers remotely controlled according to the instantaneous response of the structural component. The MR devices are driven by a SA control algorithm purposely written to modulate the dissipative capability so as to reduce base bending moment without causing excessive displacement at the top. The proposed strategy results to be really promising, since the base restraint relaxation, that favours the base moment demand reduction, is accompanied by a high enhancement of the dissipated energy due to rocking that can be even able to reduce top displacement in respect to the “fixed base rotation” conditions.

Molecular insight into γ-γ tubulin lateral interactions within the γ-tubulin ring complex (γ-TuRC)

Science.gov (United States)

Suri, Charu; Hendrickson, Triscia W.; Joshi, Harish C.; Naik, Pradeep Kumar

2014-09-01

γ-tubulin is essential for the nucleation and organization of mitotic microtubules in dividing cells. It is localized at the microtubule organizing centers and mitotic spindle fibres. The most well accepted hypothesis for the initiation of microtubule polymerization is that α/β-tubulin dimers add onto a γ-tubulin ring complex (γTuRC), in which adjacent γ-tubulin subunits bind to the underlying non-tubulin components of the γTuRC. This template thus determines the resulting microtubule lattice. In this study we use molecular modelling and molecular dynamics simulations, combined with computational MM-PBSA/MM-GBSA methods, to determine the extent of the lateral atomic interaction between two adjacent γ-tubulins within the γTuRC. To do this we simulated a γ-γ homodimer for 10 ns and calculated the ensemble average of binding free energies of -107.76 kcal/mol by the MM-PBSA method and of -87.12 kcal/mol by the MM-GBSA method. These highly favourable binding free energy values imply robust lateral interactions between adjacent γ-tubulin subunits in addition to their end-interactions longitudinally with other proteins of γTuRC. Although the functional reconstitution of γ-TuRC subunits and their stepwise in vitro assembly from purified components is not yet feasible, we nevertheless wanted to recognize hotspot amino acids responsible for key γ-γ interactions. Our free energy decomposition data from converting a compendium of amino acid residues identified an array of hotspot amino acids. A subset of such mutants can be expressed in vivo in living yeast. Because γTuRC is important for the growth of yeast, we could test whether this subset of the hotspot mutations support growth of yeast. Consistent with our model, γ-tubulin mutants that fall into our identified hotspot do not support yeast growth.

Identification of an Equivalent Linear Model for a Non-Linear Time-Variant RC-Structure

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Andersen, P.; Brincker, Rune

are investigated and compared with ARMAX models used on a running window. The techniques are evaluated using simulated data generated by the non-linear finite element program SARCOF modeling a 10-storey 3-bay concrete structure subjected to amplitude modulated Gaussian white noise filtered through a Kanai......This paper considers estimation of the maximum softening for a RC-structure subjected to earthquake excitation. The so-called Maximum Softening damage indicator relates the global damage state of the RC-structure to the relative decrease of the fundamental eigenfrequency in an equivalent linear...

Retrieval of ion distributions in RC from TWINS ENA images by CT technique

Science.gov (United States)

Ma, S.; Yan, W.; Xu, L.; Goldstein, J.; McComas, D. J.

2010-12-01

The Two Wide-angle Imaging Neutral-atom Spectrometers (TWINS) mission is the first constellation to employ imagers on two separate spacecraft to measure energetic neutral atoms (ENA) produced by charge exchange between ring current energetic ions and cold exospheric neutral atoms. By applying the 3-D volumetric pixel (voxel) computed tomography (CT) inversion method to TWINS images, parent ion populations in the ring current (RC) and auroral regions are retrieved from their ENA signals. This methodology is implemented for data obtained during the main phase of a moderate geomagnetic storm on 11 October 2008. For this storm the two TWINS satellites were located in nearly the same meridian plane at vantage points widely separated in magnetic local time, and both more than 5 RE geocentric distance from the Earth. In the retrieval process, the energetic ion fluxes to be retrieved are assumed being isotropic with respect to pitch angle. The ENA data used in this study are differential fluxes averaged over 12 sweeps (corresponding to an interval of 16 min.) at different energy levels ranging throughout the full 1--100 keV energy range of TWINS. The ENA signals have two main components: (1) a low-latitude/ high-altitude signal from trapped RC ions and (2) a low-altitude signal from precipitating ions in the auroral/subauroral ionosphere. In the retrieved ion distributions, the main part of the RC component is located around midnight toward dawn sector with L from 3 to 7 or farther, while the subauroral low-altitude component is mainly at pre-midnight. It seems that the dominant energy of the RC ions for this storm is at the lowest energy level of 1-2 keV, with another important energy band centered about 44 keV. The low-altitude component is consistent with in situ observations by DMSP/SSJ4. The result of this study demonstrates that with satellite constellations such as TWINS, using all-sky ENA imagers deployed at multiple vantage points, 3-D distribution of RC ion

An experimental investigation on the ultimate strength of epoxy repaired braced partial infilled RC frames

Science.gov (United States)

Dubey, Shailendra Kumar Damodar; Kute, Sunil

2014-09-01

Due to earthquake, buildings are damaged partially or completely. Particularly structures with soft storey are mostly affected. In general, such damaged structures are repaired and reused. In this regard, an experimental investigation was planned and conducted on models of single-bay, single-storey of partial concrete infilled reinforced concrete (RC) frames up to collapse with corner, central and diagonal steel bracings. Such collapsed frames were repaired with epoxy resin and retested. The initiative was to identify the behaviour, extent of restored ultimate strength and deflection of epoxy-retrofitted frames in comparison to the braced RC frames. The performance of such frames has been considered only for lateral loads. In comparison to bare RC frames, epoxy repaired partial infilled frames have significant increase in the lateral load capacity. Central bracing is more effective than corner and diagonal bracing. For the same load, epoxy repaired frames have comparable deflection than similar braced frames.

FRP strengthening of RC walls with openings

DEFF Research Database (Denmark)

Hansen, Christian Skodborg; Sas, Gabriel; Täljsten, Björn

2009-01-01

Strengthening reinforced concrete (RC) walls with openings using fibre reinforced polymers (FRP) has been experimentally proven to be a viable rehabilitation method. However, very few theoretical investigations are reported. In this paper two methods of analysis are presented. Since openings vary...... in size, the analysis of a strengthened wall can be divided into frame idealization method for large openings, and combined disk and frame analysis for smaller openings. The first method provides an easy to use tool in practical engineering, where the latter describes the principles of a ductile...

Successful Beam-Beam Tuneshift Compensation

Energy Technology Data Exchange (ETDEWEB)

Bishofberger, Kip Aaron [Univ. of California, Los Angeles, CA (United States)

2005-01-01

The performance of synchrotron colliders has been limited by the beam-beam limit, a maximum tuneshift that colliding bunches could sustain. Due to bunch-to-bunch tune variation and intra-bunch tune spread, larger tuneshifts produce severe emittance growth. Breaking through this constraint has been viewed as impossible for several decades. This dissertation introduces the physics of ultra-relativistic synchrotrons and low-energy electron beams, with emphasis placed on the limits of the Tevatron and the needs of a tuneshift-compensation device. A detailed analysis of the Tevatron Electron Lens (T_EL) is given, comparing theoretical models to experimental data whenever possible. Finally, results of Tevatron operations with inclusion of the T_EL are presented and analyzed. It is shown that the T_EL provides a way to shatter the previously inescapable beam-beam limit.

In RC buildings, the vertical and horizontal members (ie, the beams ...

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 10; Issue 4. Learning Earthquake Design and Construction - 18. How do Beams in RC Buildings Resist Earthquakes? C V R Murty. Classroom Volume 10 Issue 4 April 2005 pp 87-90 ...

Seismic refraction data constrain along-axis structure of the Mid-Cayman spreading center

Science.gov (United States)

Van Avendonk, H. J.; Hayman, N. W.; Harding, J.; Grevemeyer, I.; Peirce, C.; Dannowski, A.; Papenberg, C. A.

2015-12-01

The Mid-Cayman Spreading Center (MCSC) is an ultraslow (15 mm/yr) spreading ridge between the Caribbean and North American plates. From north to south the MCSC is just ~140 km long, as it is bounded to the north by the Oriente transform fault, and to the south by the Swan Islands and Walton fault systems. The neovolcanic zone is characterized by an axial valley with depths to 6000 m, and a few off-axis bathymetric highs that can be as shallow as 2000 m. The role of tectonic and magmatic processes in the creation of this bathymetric relief is not yet understood. In the 2015 CaySEIS experiment, a collaboration between German, US and UK scientists, we gathered ocean-bottom seismic refraction data along five lines across and parallel to the MCSC to determine its crustal structure. We here present the tomographic analysis of marine seismic refractions recorded along the spreading axis. The presence of thin crust here shows that the bathymetric relief of the MCSC is at least in part isostatically compensated. Much of the older ultraslow spread crust on the flanks of the MCSC may not have accreted along the deep axial valley, but it may instead have formed by exhumation of gabbros along extensional faults in the adjacent seafloor.

Health Insurance Costs and Employee Compensation: Evidence from the National Compensation Survey.

Science.gov (United States)

Anand, Priyanka

2017-12-01

This paper examines the relationship between rising health insurance costs and employee compensation. I estimate the extent to which total compensation decreases with a rise in health insurance costs and decompose these changes in compensation into adjustments in wages, non-health fringe benefits, and employee contributions to health insurance premiums. I examine this relationship using the National Compensation Survey, a panel dataset on compensation and health insurance for a sample of establishments across the USA. I find that total hourly compensation reduces by $0.52 for each dollar increase in health insurance costs. This reduction in total compensation is primarily in the form of higher employee premium contributions, and there is no evidence of a change in wages and non-health fringe benefits. These findings show that workers are absorbing at least part of the increase in health insurance costs through lower compensation and highlight the importance of examining total compensation, and not just wages, when examining the relationship between health insurance costs and employee compensation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Effect of ion compensation of the beam space charge on gyrotron operation

Energy Technology Data Exchange (ETDEWEB)

Fokin, A. P.; Glyavin, M. Yu. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Nusinovich, G. S. [Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20742-3511 (United States)

2015-04-15

In gyrotrons, the coherent radiation of electromagnetic waves takes place when the cyclotron resonance condition between the wave frequency and the electron cyclotron frequency or its harmonic holds. The voltage depression caused by the beam space charge field changes the relativistic cyclotron frequency and, hence, can play an important role in the beam-wave interaction process. In long pulse and continuous-wave regimes, the beam space charge field can be partially compensated by the ions, which appear due to the beam impact ionization of neutral molecules of residual gases in the interaction space. In the present paper, the role of this ion compensation of the beam space charge on the interaction efficiency is analyzed. We also analyze the effect of the electron velocity spread on the limiting currents and discuss some effects restricting the ion-to-beam electron density ratio in the saturation stage. It is shown that the effect of the ion compensation on the voltage depression caused by the beam space charge field can cause significant changes in the efficiency of gyrotron operation and, in some cases, even result in the break of oscillations.

Data of evolutionary structure change: 1ONAD-2D3RC [Confc[Archive

Lifescience Database Archive (English)

Full Text Available 1ONAD-2D3RC 1ONA 2D3R D C ADTIVAVELDTYPNTDIGDPSYPHIGIDIKSVRSKKTAK...WNMQNGKVGTAHIIYNSVDKRLSAVVSYPNADSATVSYDVDLDNVLPEWVRVGLSASTGLYKETNTILSWSFTSKLKT------NALHFMFNQFSKDQKDLILQGDAT... 1ONA D 1ONAD TRVSSN

A case of hyperkalemia after transfusion of irradiated red cell concentrate in mannitol-adenine-phosphate (RC-MAP)

International Nuclear Information System (INIS)

Fukui, Akira; Yokota, Kimio; Aoki, Masanori; Sari, Atsuo

1998-01-01

A 72-year-old male, 45 kg in weight, underwent anterior and posterior fixations of the lumbar vertebra. Preanesthetic blood chemistry was within normal range. Following transfusion of 400 ml of RC-MAP in two hours (11 days after blood collection and 2 days after irradiation at a dose of 20 Gy), and then another 100 ml of 400 ml RC-MAP (12 days after blood collection and 2 days after irradiation at a dose of 20 Gy), the patient's serum kalium value increased from 4.8 to 5.5 mEq/l. Even though the transfusion was immediately discontinued, the level continued to rise to 6.0 mEq/l. It subsequently fell to the normal level with glucose-insulin therapy. The hyperkalemia in this case could have been attributable to the period of storage after irradiation, the transfusion of salvaged autologous blood, and the storage state of RC-MAP. However, since the kalium values of RC-MAP and the salvaged autologous blood were not measured in this case, the exact cause was unknown. In conclusion, hyperkalemia can occur in patients during transfusion of irradiated blood. Therefore, kalium levels should be monitored carefully. (author)

Design Optimization of Hybrid FRP/RC Bridge

Science.gov (United States)

Papapetrou, Vasileios S.; Tamijani, Ali Y.; Brown, Jeff; Kim, Daewon

2018-04-01

The hybrid bridge consists of a Reinforced Concrete (RC) slab supported by U-shaped Fiber Reinforced Polymer (FRP) girders. Previous studies on similar hybrid bridges constructed in the United States and Europe seem to substantiate these hybrid designs for lightweight, high strength, and durable highway bridge construction. In the current study, computational and optimization analyses were carried out to investigate six composite material systems consisting of E-glass and carbon fibers. Optimization constraints are determined by stress, deflection and manufacturing requirements. Finite Element Analysis (FEA) and optimization software were utilized, and a framework was developed to run the complete analyses in an automated fashion. Prior to that, FEA validation of previous studies on similar U-shaped FRP girders that were constructed in Poland and Texas is presented. A finer optimization analysis is performed for the case of the Texas hybrid bridge. The optimization outcome of the hybrid FRP/RC bridge shows the appropriate composite material selection and cross-section geometry that satisfies all the applicable Limit States (LS) and, at the same time, results in the lightest design. Critical limit states show that shear stress criteria determine the optimum design for bridge spans less than 15.24 m and deflection criteria controls for longer spans. Increased side wall thickness can reduce maximum observed shear stresses, but leads to a high weight penalty. A taller cross-section and a thicker girder base can efficiently lower the observed deflections and normal stresses. Finally, substantial weight savings can be achieved by the optimization framework if base and side-wall thickness are treated as independent variables.

Learning Abstract Physical Concepts from Experience: Design and Use of an RC Circuit

Science.gov (United States)

Parra, Alfredo; Ordenes, Jorge; de la Fuente, Milton

2018-05-01

Science learning for undergraduate students requires grasping a great number of theoretical concepts in a rather short time. In our experience, this is especially difficult when students are required to simultaneously use abstract concepts, mathematical reasoning, and graphical analysis, such as occurs when learning about RC circuits. We present a simple experimental model in this work that allows students to easily design, build, and analyze RC circuits, thus providing an opportunity to test personal ideas, build graphical descriptions, and explore the meaning of the respective mathematical models, ultimately gaining a better grasp of the concepts involved. The result suggests that the simple setup indeed helps untrained students to visualize the essential points of this kind of circuit.

Design issues and cost implications of RTO/RC-ITER divertor

International Nuclear Information System (INIS)

Ibbott, C.; Antipenkov, A.; Chiocchio, S.; Federici, G.; Heidl, H.; Janeschitz, G.; Martin, E.; Tivey, R.

2000-01-01

This paper reports on the conceptual divertor design developed for the reduced technical objectives/reduced cost-international thermonuclear experimental reactor (RTO/RC-ITER). The cost drivers are discussed and a number of cost-reducing measures identified. Scaled costs, based on industrial estimates of the 1998 ITER design (Technical Basis for the ITER Final Design Report, Cost Review and Safety Analysis (FDR). ITER EDA Documentation Series No. 16. IAEA, Vienna, 1998), give for the RTO/RC-ITER ∼60% of the FDR costs. Plasma facing components (PFCs) account for 75% of the total divertor costs. Hence, PFC design simplifications are outlined in the paper showing the possibility of achieving a cost reduction of 50%. The design proposals, outlined in the paper, focus on minimising the number of sub-components and simplifying the manufacturing cycle. These changes contribute to improved reliability based on a more robust coolant design layout. The reduced space allocated to the divertor (G. Janeschitz, A. Antipenkov, V. Barabash, S. Chiocchio, G. Federici, C. Ibbott, E. Martin, R. Tivey, Overview of the Divertor Design and its Integration into RTO/RC-ITER, this conference) requires changes to the design that minimise the cassette body thickness, relocate the cassette attachments and revise the remote handling philosophy. Results of supporting electro-magnetic, neutron shielding, thermo-hydraulic and pumping conductance analyses are reported, qualifying the cassette design. A reduction in the coolant inlet temperature to 100-120 deg. C is discussed in terms of thermal-hydraulic performance and fatigue life of the heat sink. Finally, an R and D plan sets out the work needed: (1) to develop the cost saving measures of the new design; and (2) to demonstrate the reliability of the chosen technologies

State of Charge Estimation for Lithium-Ion Battery with a Temperature-Compensated Model

Directory of Open Access Journals (Sweden)

Shichun Yang

2017-10-01

Full Text Available Accurate estimation of the state of charge (SOC of batteries is crucial in a battery management system. Many studies on battery SOC estimation have been investigated recently. Temperature is an important factor that affects the SOC estimation accuracy while it is still not adequately addressed at present. This paper proposes a SOC estimator based on a new temperature-compensated model with extended Kalman Filter (EKF. The open circuit voltage (OCV, capacity, and resistance and capacitance (RC parameters in the estimator are temperature dependent so that the estimator can maintain high accuracy at various temperatures. The estimation accuracy decreases when applied in high current continuous discharge, because the equivalent polarization resistance decreases as the discharge current increases. Therefore, a polarization resistance correction coefficient is proposed to tackle this problem. The estimator also demonstrates a good performance in dynamic operating conditions. However, the equivalent circuit model shows huge uncertainty in the low SOC region, so measurement noise variation is proposed to improve the estimation accuracy there.

38 CFR 21.3023 - Nonduplication; pension, compensation, and dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Nonduplication; pension, compensation, and dependency and indemnity compensation. 21.3023 Section 21.3023 Pensions, Bonuses, and... Nonduplication; pension, compensation, and dependency and indemnity compensation. (a) Child; age 18. A child who...

[Vestibular compensation studies]. [Vestibular Compensation and Morphological Studies

Science.gov (United States)

Perachio, Adrian A. (Principal Investigator)

1996-01-01

The following topics are reported: neurophysiological studies on MVN neurons during vestibular compensation; effects of spinal cord lesions on VNC neurons during compensation; a closed-loop vestibular compensation model for horizontally canal-related MVN neurons; spatiotemporal convergence in VNC neurons; contributions of irregularly firing vestibular afferents to linear and angular VOR's; application to flight studies; metabolic measures in vestibular neurons; immediate early gene expression following vestibular stimulation; morphological studies on primary afferents, central vestibular pathways, vestibular efferent projection to the vestibular end organs, and three-dimensional morphometry and imaging.

Flexural strengthening of Reinforced Concrete (RC) Beams Retrofitted with Corrugated Glass Fiber Reinforced Polymer (GFRP) Laminates

Science.gov (United States)

Aravind, N.; Samanta, Amiya K.; Roy, Dilip Kr. Singha; Thanikal, Joseph V.

2015-01-01

Strengthening the structural members of old buildings using advanced materials is a contemporary research in the field of repairs and rehabilitation. Many researchers used plain Glass Fiber Reinforced Polymer (GFRP) sheets for strengthening Reinforced Concrete (RC) beams. In this research work, rectangular corrugated GFRP laminates were used for strengthening RC beams to achieve higher flexural strength and load carrying capacity. Type and dimensions of corrugated profile were selected based on preliminary study using ANSYS software. A total of twenty one beams were tested to study the load carrying capacity of control specimens and beams strengthened with plain sheets and corrugated laminates using epoxy resin. This paper presents the experimental and theoretical study on flexural strengthening of Reinforced Concrete (RC) beams using corrugated GFRP laminates and the results are compared. Mathematical models were developed based on the experimental data and then the models were validated.

Isolation and molecular characterization of RcSERK1: A Rosa ...

African Journals Online (AJOL)

User

2011-05-16

May 16, 2011 ... somatic embryogenesis receptor-like kinase; SP, signal peptide; SPP, .... primers used for detecting RcSERK1 gene expression were: for- .... and mainly in the PLBs but weak in the callus and rhi- ... Transformed cells in the bright light (A and E), in the dark for cell nucleuses stained with DAPI (B and F),.

Sustainable RC Beam-Column Connections with Headed Bars: A Formula for Shear Strength Evaluation

Directory of Open Access Journals (Sweden)

Minh-Tung Tran

2018-02-01

Full Text Available Beam-column joints are critical regions for reinforced concrete (RC frames subjected to earthquakes. The steel reinforcement is, in general, highly concentrated in these zones. This is why in many cases, headed bars are used. A headed bar is a longitudinal steel reinforcement whose end has a special button added to reduce the bonding length of the steel rebar. This paper establishes a formula predicting the shear strength of exterior RC beam-column connections where the beam longitudinal reinforcements use headed bars. A database was collected, which contained 30 experimental data about the exterior beam-column joints using headed bars and subjected to quasi-static cyclic loading. First, from the collected database, a statistical study was carried out to identify the most influencing parameters on the shear strength of the beam-column joints tested. The three most important parameters were identified and an empirical modified formula was developed based on the formula existing in the standards. The study showed that the results obtained from the modified formula proposed in the present study were closer to the experimental results than that obtained from the formula existing in the standards. Finally, a numerical study was performed on two T-form RC structures and the numerical results were compared with the prediction calculated from the modified formula proposed. For two investigated cases, the proposed formula provided the results in the safety side and the differences with the numerical results were less than 20%. Thus, the proposed formula can be used for a rapid assessment of the shear strength of RC joints using headed bars.

Lactobacillus rhamnosus RC007 intended for feed additive: immune-stimulatory properties and ameliorating effects on TNBS-induced colitis.

Science.gov (United States)

Dogi, C; García, G; De Moreno de LeBlanc, A; Greco, C; Cavaglieri, L

2016-09-01

Lactobacillus rhamnosus RC007 is a potential probiotic bacterium that can exert beneficial effects as supplement for animal feed, by improving the immune status in healthy host, and by providing therapeutic benefits to infected/inflamed animals. The aim of the present work was to evaluate in vivo the beneficial properties of L. rhamnosus RC007, intended for animal feed, when administered to healthy and trinitro-benzene-sulfonic-acid (TNBS) colitis induced BALB/c mice. The administration of L. rhamnosus RC007 to healthy mice during 10 days increased the phagocytic activity of peritoneal macrophages and the number of immunoglobulin A+ cells in the lamina proper of the small intestine. Significant increases of monocyte chemotactic protein 1, interleukin (IL)-10 and tumour necrosis factor alpha (TNF-α) concentrations, and in the ratio between anti- and pro-inflammatory cytokines (IL-10/TNF-α) were observed in intestinal fluids after administration of bacteria. In the inflammation model, less body weight loss, macroscopic and histological damages in the large intestine were accompanied by increased IL-10/TNF-α ratio in the intestinal fluids of mice from the L. rhamnosus-TNBS group when compared to the TNBS group. In a healthy host, the oral administration of L. rhamnosus RC007 kept the gut immune system stimulated allowing a faster response to noxious stimulus. Mice that received L. rhamnosus RC007 also decreased the severity of the intestinal inflammation.

Flexural Strengthening of RC Slabs Using a Hybrid FRP-UHPC System Including Shear Connector

Directory of Open Access Journals (Sweden)

Jiho Moon

2017-01-01

Full Text Available A polymeric hybrid composite system made of UHPC and CFRP was proposed as a retrofit system to enhance flexural strength and ductility of RC slabs. While the effectiveness of the proposed system was confirmed previously through testing three full-scale one-way slabs having two continuous spans, the slabs retrofitted with the hybrid system failed in shear. This sudden shear failure would stem from the excessive enhancement of the flexural strength over the shear strength. In this study, shear connectors were installed between the hybrid system and a RC slab. Using simple beam, only positive moment section was examined. Two full-scale RC slabs were cast and tested to failure: the first as a control and the second using this new strengthening technique. The proposed strengthening system increased the ultimate load carrying capacity of the slab by 70%, the stiffness by 60%, and toughness by 128%. The efficiency of shear connectors on ductile behavior of the retrofitted slab was also confirmed. After the UHPC top is separated from the slab, the shear connector transfer shear load and the slab system were in force equilibrium by compression in UHPC and tension in CFRP.

AN ACTUARIAL APPROACH TO ASSESSING PERSONAL INJURY COMPENSATIONS IN SINGAPORE: THEORY AND PRACTICE

OpenAIRE

FELIX W. H. CHAN; WAI-SUM CHAN; JOHNNY S. H. LI

2010-01-01

In Singapore personal injury litigations, successful claimants usually receive their compensations as a lump sum. The main advantage of a lump sum payment is that the proceedings can be concluded with a 'clean break' between the parties. The lump sum is a result of discounting the future pecuniary values into a single present-day amount, considering the time value of money and the claimant's mortality. Conventionally, lump sum awards are determined by making reference to a spread of amounts i...

Electronically tunable RC sinusoidal oscillators

International Nuclear Information System (INIS)

Florescu, Valeriu

2008-01-01

This paper presents two types of active configurations for realizing electronically tunable RC sinusoidal oscillators. The type-1 network employs two grounded scaled resistances KR 1 and KR 2 , where K is scaling factor. The frequency of oscillation W 0 is controlled conveniently by adjusting K, since W 0 appears in the form W 0 =1/K √ R 1 C 1 R 2 C 2 . For realizing the scaled resistances, an active configuration is proposed, which realizes KR 1 =R 1 /(1+f(V B )), where f(V B ) denotes a function of a controlling voltage V B . Thus the frequency tuning can be effected by controlling a voltage V B . The type-2 oscillator uses two periodically switched conductances. It is shown that the tuning of oscillation frequency can be done by varying the pulse width-to-period ratio (t/T) of the periodically switched conductances. (author)

A 500-600 MHz GaN power amplifier with RC-LC stability network

Science.gov (United States)

Ma, Xinyu; Duan, Baoxing; Yang, Yintang

2017-08-01

A 500-600 MHz high-efficiency, high-power GaN power amplifier is designed and realized on the basis of the push-pull structure. The RC-LC stability network is proposed and applied to the power amplifier circuit for the first time. The RC-LC stability network can significantly reduce the high gain out the band, which eliminates the instability of the power amplifier circuit. The developed power amplifier exhibits 58.5 dBm (700 W) output power with a 17 dB gain and 85% PAE at 500-600 MHz, 300 μs, 20% duty cycle. It has the highest PAE in P-band among the products at home and abroad. Project supported by the National Key Basic Research Program of China (No. 2014CB339901).

The IL-17F/IL-17RC Axis Promotes Respiratory Allergy in the Proximal Airways

Directory of Open Access Journals (Sweden)

Antonella De Luca

2017-08-01

Full Text Available The interleukin 17 (IL-17 cytokine and receptor family is central to antimicrobial resistance and inflammation in the lung. Mice lacking IL-17A, IL-17F, or the IL-17RA subunit were compared with wild-type mice for susceptibility to airway inflammation in models of infection and allergy. Signaling through IL-17RA was required for efficient microbial clearance and prevention of allergy; in the absence of IL-17RA, signaling through IL-17RC on epithelial cells, predominantly by IL-17F, significantly exacerbated lower airway Aspergillus or Pseudomonas infection and allergic airway inflammation. In contrast, following infection with the upper respiratory pathogen Staphylococcus aureus, the IL-17F/IL-17RC axis mediated protection. Thus, IL-17A and IL-17F exert distinct biological effects during pulmonary infection; the IL-17F/IL-17RC signaling axis has the potential to significantly worsen pathogen-associated inflammation of the lower respiratory tract in particular, and should be investigated further as a therapeutic target for treating pathological inflammation in the lung.

A Novel Image Encryption Scheme Based on Intertwining Chaotic Maps and RC4 Stream Cipher

Science.gov (United States)

Kumari, Manju; Gupta, Shailender

2018-03-01

As the systems are enabling us to transmit large chunks of data, both in the form of texts and images, there is a need to explore algorithms which can provide a higher security without increasing the time complexity significantly. This paper proposes an image encryption scheme which uses intertwining chaotic maps and RC4 stream cipher to encrypt/decrypt the images. The scheme employs chaotic map for the confusion stage and for generation of key for the RC4 cipher. The RC4 cipher uses this key to generate random sequences which are used to implement an efficient diffusion process. The algorithm is implemented in MATLAB-2016b and various performance metrics are used to evaluate its efficacy. The proposed scheme provides highly scrambled encrypted images and can resist statistical, differential and brute-force search attacks. The peak signal-to-noise ratio values are quite similar to other schemes, the entropy values are close to ideal. In addition, the scheme is very much practical since having lowest time complexity then its counterparts.

Assessment of Seismic Vulnerability of Steel and RC Moment Buildings Using HAZUS and Statistical Methodologies

Directory of Open Access Journals (Sweden)

Iman Mansouri

2017-01-01

Full Text Available Designer engineers have always the serious challenge regarding the choice of the kind of structures to use in the areas with significant seismic activities. Development of fragility curve provides an opportunity for designers to select a structure that will have the least fragility. This paper presents an investigation into the seismic vulnerability of both steel and reinforced concrete (RC moment frames using fragility curves obtained by HAZUS and statistical methodologies. Fragility curves are employed for several probability parameters. Fragility curves are used to assess several probability parameters. Furthermore, it examines whether the probability of the exceedence of the damage limit state is reduced as expected. Nonlinear dynamic analyses of five-, eight-, and twelve-story frames are carried out using Perform 3D. The definition of damage states is based on the descriptions provided by HAZUS, which gives the limit states and the associated interstory drift limits for structures. The fragility curves show that the HAZUS procedure reduces probability of damage, and this reduction is higher for RC frames. Generally, the RC frames have higher fragility compared to steel frames.

GENERACIÓN DE POLINOMIOS DE SCHUBERT CON COCOA II: GRAFOS RC.

Directory of Open Access Journals (Sweden)

Fernando Novoa

2004-06-01

Full Text Available El polinomio de Schubert asociado a una permutación w es codificado por medio de la información contenida en ciertos grafos rc. Presentamos un programa para el cómputo de los polinomios de Schubert por medio de movimientos definidos sobre estos grafos.

A three-layer distributed RC network with two transmission zeros

Science.gov (United States)

Huelsman, L. P.

1974-01-01

This report describes the properties of a three-layer distributed RC network consisting of two resistive layers separated by a dielectric which may be used to realize two zeros of transmission on the j-omega axis of the complex frequency plane. The relative location of the two zeros is controlled by the location of a contact placed on one of the resistive layers.

Re-Planning for Compensator-Based IMRT with Original Compensators

International Nuclear Information System (INIS)

Zhang, Geoffrey; Feygelman, Vladimir; Stevens, Craig; Li Weiqi; Leuthold, Susan; Springett, Gregory; Hoffe, Sarah

2011-01-01

Compared with multileaf collimator (MLC)-based intensity-modulated radiotherapy (IMRT) for moving targets, compensator-based IMRT has advantages such as shorter beam-on time, fewer monitor units with potentially decreased secondary carcinogenesis risk, better optimization-to-deliverable dose conversion, and often better dose conformity. Some of the disadvantages include additional time for the compensators to be built and delivered, as well as extra cost. Patients undergoing treatment of abdominal cancers often experience weight loss. It would be necessary to account for this change in weight with a new plan and a second set of compensators. However, this would result in treatment delays and added costs. We have developed a method to re-plan the patient using the same set of compensators. Because the weight changes seen with the treatment of abdominal cancers are usually relatively small, a new 4D computed tomography (CT) acquired in the treatment position with markers on the original isocenter tattoos can be registered to the original planning scan. The contours of target volumes from the original scans are copied to the new scan after fusion. The original compensator set can be used together with a few field-in-field (FiF) beams defined by the MLC (or beams with cerrobend blocks for accelerators not equipped with a MLC). The weights of the beams with compensators are reduced so that the FiF or blocked beams can be optimized to mirror the original plan and dose distribution. Seven abdominal cancer cases are presented using this technique. The new plan on the new planning CT images usually has the same dosimetric quality as the original. The target coverage and dose uniformity are improved compared with the plan without FiF/block modification. Techniques combining additional FiF or blocked beams with the original compensators optimize the treatment plans when patients lose weight and save time and cost compared with generating plans with a new set of compensators.

Glass Fiber Reinforced Polymer (GFRP Bars for Enhancing the Flexural Performance of RC Beams Using Side-NSM Technique

Directory of Open Access Journals (Sweden)

Md. Akter Hosen

2017-05-01

Full Text Available Reinforced concrete (RC structures require strengthening for numerous factors, such as increased load, modification of the structural systems, structural upgrade or errors in the design and construction stages. The side near-surface mounted (SNSM strengthening technique with glass fiber-reinforced polymer (GFRP bars is a relatively new emerging technique for enhancing the flexural capacities of existing RC elements. Nine RC rectangular beams were flexurally strengthened with this technique and tested under four-point bending loads until failure. The main goal of this study is to optimize the structural capacity of the RC beams by varying the amount of strengthening reinforcement and bond length. The experimental test results showed that strengthening with SNSM GFRP bars significantly enhanced the flexural responses of the specimens compared with the control specimen. The first cracking and ultimate loads, energy absorption capacities, ductility and stiffness were remarkably enhanced by the SNSM technique. It was also confirmed that the bond length of the strengthened reinforcement greatly influences the energy absorption capacities, ductility and stiffness. The effect of the bond length on these properties is more significant compared to the amount of strengthening reinforcement.

Advancement in PET quantification using 3D-OP-OSEM point spread function reconstruction with the HRRT

Energy Technology Data Exchange (ETDEWEB)

Varrone, Andrea; Sjoeholm, Nils; Gulyas, Balazs; Halldin, Christer; Farde, Lars [Karolinska Hospital, Karolinska Institutet, Department of Clinical Neuroscience, Psychiatry Section and Stockholm Brain Institute, Stockholm (Sweden); Eriksson, Lars [Karolinska Hospital, Karolinska Institutet, Department of Clinical Neuroscience, Psychiatry Section and Stockholm Brain Institute, Stockholm (Sweden); Siemens Molecular Imaging, Knoxville, TN (United States); University of Stockholm, Department of Physics, Stockholm (Sweden)

2009-10-15

Image reconstruction including the modelling of the point spread function (PSF) is an approach improving the resolution of the PET images. This study assessed the quantitative improvements provided by the implementation of the PSF modelling in the reconstruction of the PET data using the High Resolution Research Tomograph (HRRT). Measurements were performed on the NEMA-IEC/2001 (Image Quality) phantom for image quality and on an anthropomorphic brain phantom (STEPBRAIN). PSF reconstruction was also applied to PET measurements in two cynomolgus monkeys examined with [{sup 18}F]FE-PE2I (dopamine transporter) and with [{sup 11}C]MNPA (D{sub 2} receptor), and in one human subject examined with [{sup 11}C]raclopride (D{sub 2} receptor). PSF reconstruction increased the recovery coefficient (RC) in the NEMA phantom by 11-40% and the grey to white matter ratio in the STEPBRAIN phantom by 17%. PSF reconstruction increased binding potential (BP{sub ND}) in the striatum and midbrain by 14 and 18% in the [{sup 18}F]FE-PE2I study, and striatal BP{sub ND} by 6 and 10% in the [{sup 11}C]MNPA and [{sup 11}C]raclopride studies. PSF reconstruction improved quantification by increasing the RC and thus reducing the partial volume effect. This method provides improved conditions for PET quantification in clinical studies with the HRRT system, particularly when targeting receptor populations in small brain structures. (orig.)

A proposal for seismic evaluation index of mid-rise existing RC buildings in Afghanistan

Science.gov (United States)

Naqi, Ahmad; Saito, Taiki

2017-10-01

Mid-rise RC buildings gradually rise in Kabul and entire Afghanistan since 2001 due to rapid increase of population. To protect the safety of resident, Afghan Structure Code was issued in 2012. But the building constructed before 2012 failed to conform the code requirements. In Japan, new sets of rules and law for seismic design of buildings had been issued in 1981 and severe earthquake damage was disclosed for the buildings designed before 1981. Hence, the Standard for Seismic Evaluation of RC Building published in 1977 has been widely used in Japan to evaluate the seismic capacity of existing buildings designed before 1981. Currently similar problem existed in Afghanistan, therefore, this research examined the seismic capacity of six RC buildings which were built before 2012 in Kabul by applying the seismic screening procedure presented by Japanese standard. Among three screening procedures with different capability, the less detailed screening procedure, the first level of screening, is applied. The study founds an average seismic index (IS-average=0.21) of target buildings. Then, the results were compared with those of more accurate seismic evaluation procedures of Capacity Spectrum Method (CSM) and Time History Analysis (THA). The results for CSM and THA show poor seismic performance of target buildings not able to satisfy the safety design limit (1/100) of the maximum story drift. The target buildings are then improved by installing RC shear walls. The seismic indices of these retrofitted buildings were recalculated and the maximum story drifts were analyzed by CSM and THA. The seismic indices and CSM and THA results are compared and found that building with seismic index larger than (IS-average =0.4) are able to satisfy the safety design limit. Finally, to screen and minimize the earthquake damage over the existing buildings, the judgement seismic index (IS-Judgment=0.5) for the first level of screening is proposed.

Reactive power compensator

Science.gov (United States)

El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Reactive power compensator

Energy Technology Data Exchange (ETDEWEB)

El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

1992-01-01

A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

Time-variant flexural reliability of RC beams with externally bonded CFRP under combined fatigue-corrosion actions

International Nuclear Information System (INIS)

Bigaud, David; Ali, Osama

2014-01-01

Time-variant reliability analysis of RC highway bridges strengthened with carbon fibre reinforced polymer CFRP laminates under four possible competing damage modes (concrete crushing, steel rupture after yielding, CFRP rupture and FRP plate debonding) and three degradation factors is analyzed in terms of reliability index β using FORM. The first degradation factor is chloride-attack corrosion which induces reduction in steel area and concrete cover cracking at characteristic key times (corrosion initiation, severe surface cover cracking). The second degradation factor considered is fatigue which leads to damage in concrete and steel rebar. Interaction between corrosion and fatigue crack growth in steel reinforcing bars is implemented. The third degradation phenomenon is the CFRP properties deterioration due to aging. Considering these three degradation factors, the time-dependent flexural reliability profile of a typical simple 15 m-span intermediate girder of a RC highway bridge is constructed under various traffic volumes and under different corrosion environments. The bridge design options follow AASHTO-LRFD specifications. Results of the study have shown that the reliability is very sensitive to factors governing the corrosion. Concrete damage due to fatigue slightly affects reliability profile of non-strengthened section, while service life after strengthening is strongly related to fatigue damage in concrete. - Highlights: • We propose a method to follow the time-variant reliability of strengthened RC beams. • We consider multiple competing failure modes of CFRP strengthened RC beams. • We consider combined degradation mechanisms (corrosion, fatigue, ageing of CFRP)

Barometrický výškoměr pro RC modely letadel

OpenAIRE

Dujíček, Martin

2012-01-01

Cílem této práce je návrh barometrického výškoměru určeného pro RC modely letadel. Během letu je zaznamenávána hodnota ze snímacího prvku do paměti. Po ukončení letu a po připojení zařízení k počítači je možné data přečíst nebo smazat. Přijatá data je dále možné zpracovat například do grafické podoby. The aim of this thesis is to design barometric altimeter for RC plane models. During the flight the value from sensing element is stored in memory. After the flight and connect to computer it...

Effect of Large Negative Phase of Blast Loading on Structural Response of RC Elements

Directory of Open Access Journals (Sweden)

Syed Zubair Iman

2016-01-01

Full Text Available Structural response of reinforced concrete (RC elements for analysis and design are often obtained using the positive phase of the blast pressure curve disregarding the negative phase assuming insignificant contribution from the negative phase of the loading. Although, some insight on the effect of negative phase of blast pressure based on elastic single-degree-of-freedom (SDOF analysis was presented before, the influence of negative phase on different types of resistance functions of SDOF models and on realistic finite element analysis has not been explored. In this study, the effects of inclusion of pulse negative phase on structural response of RC elements from SDOF analysis and from more detailed finite element analysis have been investigated. Investigation of SDOF part has been conducted using MATLAB code that utilizes non-linear resistance functions of SDOF model. Detailed numerical investigation using finite element code DIANA was conducted on the significance of the negative phase on structural response. In the FE model, different support stiffness was used to explore the effect of support stiffness on the structural response due to blast negative phase. Results from SDOF and FE analyses present specific situations where the effect of large negative phase was found to be significant on the structural response of RC elements.

Evaluation of Structural Robustness against Column Loss: Methodology and Application to RC Frame Buildings.

Science.gov (United States)

Bao, Yihai; Main, Joseph A; Noh, Sam-Young

2017-08-01

A computational methodology is presented for evaluating structural robustness against column loss. The methodology is illustrated through application to reinforced concrete (RC) frame buildings, using a reduced-order modeling approach for three-dimensional RC framing systems that includes the floor slabs. Comparisons with high-fidelity finite-element model results are presented to verify the approach. Pushdown analyses of prototype buildings under column loss scenarios are performed using the reduced-order modeling approach, and an energy-based procedure is employed to account for the dynamic effects associated with sudden column loss. Results obtained using the energy-based approach are found to be in good agreement with results from direct dynamic analysis of sudden column loss. A metric for structural robustness is proposed, calculated by normalizing the ultimate capacities of the structural system under sudden column loss by the applicable service-level gravity loading and by evaluating the minimum value of this normalized ultimate capacity over all column removal scenarios. The procedure is applied to two prototype 10-story RC buildings, one employing intermediate moment frames (IMFs) and the other employing special moment frames (SMFs). The SMF building, with its more stringent seismic design and detailing, is found to have greater robustness.

Investigation of the fittest shear transfer model used to FEM analysis of RC structures

International Nuclear Information System (INIS)

Endo, Tatumi; Aoyagi, Masao; Endo, Takao

1988-01-01

In order to rationalize the design method of reinforced concrete (RC) structures in the nuclear power plant, the structural analysis, which is able to simulate the seismic behavior of RC structures, should be established. In this report, the investigation of shear transfer model at shear plane to be applied to FEM analysis is performed. Main conclusions obtained within the limit of the study are as follows. 1. Development of the shear transfer model at shear plane. 1) Two shear transfer models are developed to be used to the 2-dimensional nonlinear FEM analysis. 2) In one model suggested, reinforcements are modeled by plate elements and the nonlinearity of concrete surrounding reinforcement but the properties of bond-slip relation between concrete and reinforcements is also considered. 3) In another model, reinforcements are modeled by equivalent concrete properties, in which axial regidity and dowel effects of reinforcements are considered. 2. Verification of the suggested model. 1) It is confirmed that the computational results using the above-mentioned model could simulate the experimental ones fairly well. 2) Considering the application to the analysis of RC structures in the design, the model, in which reinforcement are modeled by equivalent concrete properties, is useful in view point of accuracy and simplicity. (author)

Reactive power compensating system

Energy Technology Data Exchange (ETDEWEB)

Williams, Timothy J. (Redondo Beach, CA); El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Seattle, WA)

1987-01-01

The reactive power of an induction machine is compensated by providing fixed capacitors on each phase line for the minimum compensation required, sensing the current on one line at the time its voltage crosses zero to determine the actual compensation required for each phase, and selecting switched capacitors on each line to provide the balance of the compensation required.

Digital Compensation in IQ Modulator Using Optimization—A State-Space Approach

Directory of Open Access Journals (Sweden)

Lim AGKC

2005-01-01

Full Text Available In DSP-based IQ modulators generating CPFSK signals, shortcomings in the implementation of the analog reconstruction filters result in the loss of the constant envelope property of the output CPFSK signal. These ripples cause undesirable spreading of the transmitted signal spectrum into adjacent channels when the signal passes through nonlinear elements in the transmission path and the consequent failure of the transmitted signal in meeting transmission standards requirements. Therefore, digital techniques compensating for these shortcomings play an important role in enhancing the performance of the IQ modulation system. Recently, several methods have been proposed in the literature to digitally compensate for the imperfections in the transfer characteristics of the analog reconstruction filters. Although these methods have been shown to be effective in removing the output envelope ripples, they result in filters of high orders and are therefore computationally demanding to implement on the DSP. Furthermore, previous techniques suffer from numerical instabilities as a result of matrix inversion in the process of calculating the solution vector. In this paper, we present two new techniques for designing the digital compensation filters by means of optimization to address the limitations of previous solutions. Design of control systems by optimization is now a standard technique. Simulation examples show that these techniques are effective and lead to substantial improvement of the output envelope ripples.

The values of the parameters of some multilayer distributed RC null networks

Science.gov (United States)

Huelsman, L. P.; Raghunath, S.

1974-01-01

In this correspondence, the values of the parameters of some multilayer distributed RC notch networks are determined, and the usually accepted values are shown to be in error. The magnitude of the error is illustrated by graphs of the frequency response of the networks.

Spreading convulsions, spreading depolarization and epileptogenesis in human cerebral cortex

DEFF Research Database (Denmark)

Dreier, Jens P; Major, Sebastian; Pannek, Heinz-Wolfgang

2012-01-01

Spreading depolarization of cells in cerebral grey matter is characterized by massive ion translocation, neuronal swelling and large changes in direct current-coupled voltage recording. The near-complete sustained depolarization above the inactivation threshold for action potential generating...... stimulations. Eventually, epileptic field potentials were recorded during the period that had originally seen spreading depression of activity. Such spreading convulsions are characterized by epileptic field potentials on the final shoulder of the large slow potential change of spreading depolarization. We...

Friction correction for model ship resistance and propulsion tests in ice at NRC's OCRE-RC

Directory of Open Access Journals (Sweden)

Michael Lau

2018-05-01

Full Text Available This paper documents the result of a preliminary analysis on the influence of hull-ice friction coefficient on model resistance and power predictions and their correlation to full-scale measurements. The study is based on previous model-scale/full-scale correlations performed on the National Research Council - Ocean, Coastal, and River Engineering Research Center's (NRC/OCRE-RC model test data. There are two objectives for the current study: (1 to validate NRC/OCRE-RC's modeling standards in regarding to its practice of specifying a CFC (Correlation Friction Coefficient of 0.05 for all its ship models; and (2 to develop a correction methodology for its resistance and propulsion predictions when the model is prepared with an ice friction coefficient slightly deviated from the CFC of 0.05. The mean CFC of 0.056 and 0.050 for perfect correlation as computed from the resistance and power analysis, respectively, have justified NRC/OCRE-RC's selection of 0.05 for the CFC of all its models. Furthermore, a procedure for minor friction corrections is developed. Keywords: Model test, Ice resistance, Power, Friction correction, Correlation friction coefficient

Derivation of the clinical grade human embryonic stem cell line RCe016-A (RC-12

Directory of Open Access Journals (Sweden)

P.A. De Sousa

2016-05-01

Full Text Available The human embryonic stem cell line RCe016-A (RC-12 was derived under quality assured compliance with UK regulations, EU Directives and International guidance for tissue procurement, processing and storage according to good manufacturing practice (GMP standards. The cell line was derived from a cryopreserved blastocyst stage embryo voluntarily donated as surplus to fertility requirements following informed consent. RCe016-A (RC-12 shows normal pluripotency marker expression and differentiation to three germ layers in vitro. Karyology revealed a mixed male karyotype at early passage (P15, which resolved as normal 46XY by passage 33. Microsatellite PCR identity, HLA and blood group typing data is available.

A monolithic constant-fraction discriminator using distributed R-C delay-line shaping

International Nuclear Information System (INIS)

Simpson, M.L.; Young, G.R.; Xu, M.

1995-01-01

A monolithic, CMOS, constant-fraction discriminator (CFD) was fabricated in the Orbit Semiconductor, 1.2 μ N-well process. This circuit uses an on-chip, distributed, R-C delay-line to realize the constant-fraction shaping. The delay-line is constructed from a narrow, 500-μ serpentine layer of polysilicon above a wide, grounded, second layer of polysilicon. This R-C delay-line generates about 1.1 ns of delay for 5 ns risetime signals with a slope degradation of only ≅ 15% and an amplitude reduction of about 6.1%. The CFD also features an automatic walk adjustment. The entire circuit, including the delay line, has a 200 μ pitch and is 950 μ long. The walk for a 5 ns risetime signal was measured as ± 100 ps over the 100:1 dynamic range from -15 mV to -1.5 mV. to -1.5 V. The CFD consumes 15 mW

The effect of X-ray irradiation on changes of blood chemistry in RC-MAP and CPD-whole blood after irradiation

International Nuclear Information System (INIS)

Hirose, Tetsuhito; Katayama, Norihumi; Okamoto, Yukiharu; Tsuda, Tadaaki; Ota, Kiichiro; Nishioka, Shingo; Tsumura, Michiyo

1997-01-01

The Japanese Welfare Ministry recommended to irradiate transfused blood in order to inactivate lymphocytes, thereby preventing from transfusion associated graft-versus-host disease (PT-GVHD). But an adequate dose of irradiation applied to various kinds of transfused blood has not yet known. We investigated the effect of a irradiation dose of 15 Gy (gray) on changes of plasma K, GOT, BUN and total protein (T.P) in RC-MAP (MAP) and CPD added whole blood (CPD) after days of storage of irradiation. There was a significant increase of potassium (K) in plasma in irradiated RC-MAP, compared with those in non-irradiated RC-MAP, after storage from day 2. Plasma K level in irradiated CPD increased more than those in non-irradiated CPD after storage at day 5. No different increases in plasma GOT, BUN and T.P levels were not shown in irradiated RC-MAP and CPD. Our data led to a conclusion that a adequate irradiated dose seemed to be different in various kinds of transfused blood to inactivate lymphocyte for the prevention of PT-GVHD. (author)

Nonlinear interaction analysis of RC cylindrical tank with subsoil by adopting two kinds of constitutive models for ground and structure

Science.gov (United States)

Lewiński, Paweł M.; Dudziak, Sławomir

2018-01-01

In the paper, two kinds of constitutive models for ground and structure were adopted for the nonlinear interaction analysis of the RC cylindrical tank with subsoil. The paper discusses deformational and incremental approaches to a nonlinear FE analysis of soil-structure interaction including the description of behaviour of the RC structure and the subsoil under short-term loading. Moreover, a non-linear elastic-brittle-plastic analysis of RC axisymmetric structures using finite element iterative techniques is presented. The constitutive laws for concrete and subsoil are developed in compliance with the deformational and plastic flow theories of plasticity. Two examples of an FE analysis of soil-structure interaction were performed and the results were analysed.

Power Efficient Gigabit Communication Over Capacitively Driven RC-Limited On-Chip Interconnects

NARCIS (Netherlands)

Mensink, E.; Schinkel, Daniel; Klumperink, Eric A.M.; van Tuijl, Adrianus Johannes Maria; Nauta, Bram

2010-01-01

Abstract—This paper presents a set of circuit techniques to achieve high data rate point-to-point communication over long on-chip RC-limited wire-pairs. The ideal line termination impedances for a flat transfer function with linear phase (pure delay) are derived, using an s-parameter wire-pair

Spreading Depression, Spreading Depolarizations, and the Cerebral Vasculature

DEFF Research Database (Denmark)

Ayata, Cenk; Lauritzen, Martin

2015-01-01

Spreading depression (SD) is a transient wave of near-complete neuronal and glial depolarization associated with massive transmembrane ionic and water shifts. It is evolutionarily conserved in the central nervous systems of a wide variety of species from locust to human. The depolarization spreads...

Essays in Executive Compensation

NARCIS (Netherlands)

D. Zhang (Dan)

2012-01-01

textabstractThis dissertation focuses on how executive compensation is designed and its implications for corporate finance and government regulations. Chapter 2 analyzes several proposals to restrict CEO compensation and calibrates two models of executive compensation that describe how firms would

FRP-RC Beam in Shear: Mechanical Model and Assessment Procedure for Pseudo-Ductile Behavior

Directory of Open Access Journals (Sweden)

Floriana Petrone

2014-07-01

Full Text Available This work deals with the development of a mechanics-based shear model for reinforced concrete (RC elements strengthened in shear with fiber-reinforced polymer (FRP and a design/assessment procedure capable of predicting the failure sequence of resisting elements: the yielding of existing transverse steel ties and the debonding of FRP sheets/strips, while checking the corresponding compressive stress in concrete. The research aims at the definition of an accurate capacity equation, consistent with the requirement of the pseudo-ductile shear behavior of structural elements, that is, transverse steel ties yield before FRP debonding and concrete crushing. For the purpose of validating the proposed model, an extended parametric study and a comparison against experimental results have been conducted: it is proven that the common accepted rule of assuming the shear capacity of RC members strengthened in shear with FRP as the sum of the maximum contribution of both FRP and stirrups can lead to an unsafe overestimation of the shear capacity. This issue has been pointed out by some authors, when comparing experimental shear capacity values with the theoretical ones, but without giving a convincing explanation of that. In this sense, the proposed model represents also a valid instrument to better understand the mechanical behavior of FRP-RC beams in shear and to calculate their actual shear capacity.

A comparative mathematical analysis of RL and RC electrical circuits via Atangana-Baleanu and Caputo-Fabrizio fractional derivatives

Science.gov (United States)

Abro, Kashif Ali; Memon, Anwar Ahmed; Uqaili, Muhammad Aslam

2018-03-01

This research article is analyzed for the comparative study of RL and RC electrical circuits by employing newly presented Atangana-Baleanu and Caputo-Fabrizio fractional derivatives. The governing ordinary differential equations of RL and RC electrical circuits have been fractionalized in terms of fractional operators in the range of 0 ≤ ξ ≤ 1 and 0 ≤ η ≤ 1. The analytic solutions of fractional differential equations for RL and RC electrical circuits have been solved by using the Laplace transform with its inversions. General solutions have been investigated for periodic and exponential sources by implementing the Atangana-Baleanu and Caputo-Fabrizio fractional operators separately. The investigated solutions have been expressed in terms of simple elementary functions with convolution product. On the basis of newly fractional derivatives with and without singular kernel, the voltage and current have interesting behavior with several similarities and differences for the periodic and exponential sources.

Exploring the importance of different items as reasons for leaving emergency medical services between fully compensated, partially compensated, and non-compensated/volunteer samples.

Science.gov (United States)

Blau, Gary; Chapman, Susan; Gibson, Gregory; Bentley, Melissa A

2011-01-01

The purpose of our study was to investigate the importance of different items as reasons for leaving the Emergency Medical Service (EMS) profession. An exit survey was returned by three distinct EMS samples: 127 full compensated, 45 partially compensated and 72 non-compensated/volunteer respondents, who rated the importance of 17 different items for affecting their decision to leave EMS. Unfortunately, there were a high percentage of "not applicable" responses for 10 items. We focused on those seven items that had a majority of useable responses across the three samples. Results showed that the desire for better pay and benefits was a more important reason for leaving EMS for the partially compensated versus fully compensated respondents. Perceived lack of advancement opportunity was a more important reason for leaving for the partially compensated and volunteer groups versus the fully compensated group. Study limitations are discussed and suggestions for future research offered.

Whiplash and the compensation hypothesis.

Science.gov (United States)

Spearing, Natalie M; Connelly, Luke B

2011-12-01

Review article. To explain why the evidence that compensation-related factors lead to worse health outcomes is not compelling, either in general, or in the specific case of whiplash. There is a common view that compensation-related factors lead to worse health outcomes ("the compensation hypothesis"), despite the presence of important, and unresolved sources of bias. The empirical evidence on this question has ramifications for the design of compensation schemes. Using studies on whiplash, this article outlines the methodological problems that impede attempts to confirm or refute the compensation hypothesis. Compensation studies are prone to measurement bias, reverse causation bias, and selection bias. Errors in measurement are largely due to the latent nature of whiplash injuries and health itself, a lack of clarity over the unit of measurement (specific factors, or "compensation"), and a lack of appreciation for the heterogeneous qualities of compensation-related factors and schemes. There has been a failure to acknowledge and empirically address reverse causation bias, or the likelihood that poor health influences the decision to pursue compensation: it is unclear if compensation is a cause or a consequence of poor health, or both. Finally, unresolved selection bias (and hence, confounding) is evident in longitudinal studies and natural experiments. In both cases, between-group differences have not been addressed convincingly. The nature of the relationship between compensation-related factors and health is unclear. Current approaches to testing the compensation hypothesis are prone to several important sources of bias, which compromise the validity of their results. Methods that explicitly test the hypothesis and establish whether or not a causal relationship exists between compensation factors and prolonged whiplash symptoms are needed in future studies.

Applications of electron lenses: scraping of high-power beams, beam-beam compensation, and nonlinear optics

Energy Technology Data Exchange (ETDEWEB)

Stancari, Giulio

2014-09-11

Electron lenses are pulsed, magnetically confined electron beams whose current-density profile is shaped to obtain the desired effect on the circulating beam. Electron lenses were used in the Fermilab Tevatron collider for bunch-by-bunch compensation of long-range beam-beam tune shifts, for removal of uncaptured particles in the abort gap, for preliminary experiments on head-on beam-beam compensation, and for the demonstration of halo scraping with hollow electron beams. Electron lenses for beam-beam compensation are being commissioned in the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL). Hollow electron beam collimation and halo control were studied as an option to complement the collimation system for the upgrades of the Large Hadron Collider (LHC) at CERN; a conceptual design was recently completed. Because of their electric charge and the absence of materials close to the proton beam, electron lenses may also provide an alternative to wires for long-range beam-beam compensation in LHC luminosity upgrade scenarios with small crossing angles. At Fermilab, we are planning to install an electron lens in the Integrable Optics Test Accelerator (IOTA, a 40-m ring for 150-MeV electrons) as one of the proof-of-principle implementations of nonlinear integrable optics to achieve large tune spreads and more stable beams without loss of dynamic aperture.

Ion distributions in RC at different energy levels retrieved from TWINS ENA images by voxel CT tech

Science.gov (United States)

Ma, S. Y.; McComas, David; Xu, Liang; Goldstein, Jerry; Yan, Wei-Nan

2012-07-01

Distributions of energetic ions in the RC regions in different energy levels are retrieved by using 3-D voxel CT inversion method from ENA measurements onboard TWINS constellation during the main phase of a moderate geomagnetic storm. It is assumed that the ion flux distribution in the RC is anisotropic in regard to pitch angle which complies with the adiabatic invariance of the magnetic moment as ion moving in the dipole magnetic mirror field. A semi-empirical model of the RC ion distribution in the magnetic equator is quoted to form the ion flux distribution shape at off-equatorial latitudes by mapping. For the concerned time interval, the two satellites of the TWINS flying in double Molnia orbits were located in nearly the same meridian plane at vantage points widely separated in magnetic local time, and both more than 5 RE geocentric distance from the Earth. The ENA data used in this study are differential fluxes averaged over 12 sweeps (corresponding to an interval of 16 min.) at different energy levels ranging from about 1 to 100 keV. The retrieved ion distributions show that in total the main part of the RC is located in the region with L value larger than 4, tending to increase at larger L. It reveals that there are two distinct dominant energy bands at which the ion fluxes are significantly larger magnitude than at other energy levels, one is at lower level around 2 keV and the other at higher level of 30-100 keV. Furthermore, it is very interesting that the peak fluxes of the RC ions at the two energy bands occurred in different magnetic local time, low energy ions appear preferentially in after midnight, while the higher energy ions mainly distributed around midnight and pre-midnight. This new profile is worthy of further study and needs to be demonstrated by more cases.

Understanding of self-terminating pulse generation using silicon controlled rectifier and RC load

Energy Technology Data Exchange (ETDEWEB)

Chang, Chris, E-mail: chrischang81@gmail.com; Karunasiri, Gamani, E-mail: karunasiri@nps.edu [Department of Physics, Naval Postgraduate School, Monterey, CA 93943 (United States); Alves, Fabio, E-mail: falves@alionscience.com [Alion Science and Technology at NPS, Monterey, CA 93943 (United States)

2016-01-15

Recently a silicon controlled rectifier (SCR)-based circuit that generates self-terminating voltage pulses was employed for the detection of light and ionizing radiation in pulse mode. The circuit consisted of a SCR connected in series with a RC load and DC bias. In this paper, we report the investigation of the physics underlying the pulsing mechanism of the SCR-based. It was found that during the switching of SCR, the voltage across the capacitor increased beyond that of the DC bias, thus generating a reverse current in the circuit, which helped to turn the SCR off. The pulsing was found to be sustainable only for a specific range of RC values depending on the SCR’s intrinsic turn-on/off times. The findings of this work will help to design optimum SCR based circuits for pulse mode detection of light and ionizing radiation without external amplification circuitry.

Development of Shear Capacity Prediction Model for FRP-RC Beam without Web Reinforcement

Directory of Open Access Journals (Sweden)

Md. Arman Chowdhury

2016-01-01

Full Text Available Available codes and models generally use partially modified shear design equation, developed earlier for steel reinforced concrete, for predicting the shear capacity of FRP-RC members. Consequently, calculated shear capacity shows under- or overestimation. Furthermore, in most models some affecting parameters of shear strength are overlooked. In this study, a new and simplified shear capacity prediction model is proposed considering all the parameters. A large database containing 157 experimental results of FRP-RC beams without shear reinforcement is assembled from the published literature. A parametric study is then performed to verify the accuracy of the proposed model. Again, a comprehensive review of 9 codes and 12 available models is done, published back from 1997 to date for comparison with the proposed model. Hence, it is observed that the proposed equation shows overall optimized performance compared to all the codes and models within the range of used experimental dataset.

A moving pole-placement compensation design method to increase the bandwidth of RC-damper-based dual “Buck-Boost” AC/DC converter

DEFF Research Database (Denmark)

Wu, Weimin; Qin, Weibo; Wang, Houqin

2017-01-01

the “Buck” mode, the control-to-grid current transfer function of this dual “Buck-Boost” AC/DC converter has a movable zero, which is related to the input power and the output DC voltage. When the input power increases, the movable zero will slide to the lower frequency range. And then, the gain between...... the cut-off frequency point and the resonant frequency of LCL filter will swell up, resulting in reduced amplitude margin and suppressed bandwidth of system. Based on the theoretical analysis, a new dynamic pole placement compensation control design method is proposed for this dual AC/DC converter...

Immunity to experimental Salmonella typhimurium infections in rats. Transfer of immunity with primed CD45RC+ and CD45RC- CD4 T-cell subpopulations

DEFF Research Database (Denmark)

Thygesen, P; Christensen, H B; Hougen, H P

1996-01-01

The protective effect of primed CD4 T cells against a lethal dose of Salmonella typhimurium was studied in Lewis rats. Primed CD4 T cells were obtained by inoculating Lewis rats with a non-lethal dose of S. typhimurium. Four weeks after the infection, spleen CD4 T cells were separated by antibody......-induced increase in CD45RC+ cells is most likely due to generation of antigen-specific memory T cells....

RC beams shear-strengthened with fabric-reinforced-cementitious-matrix (FRCM) composite

Science.gov (United States)

Loreto, Giovanni; Babaeidarabad, Saman; Leardini, Lorenzo; Nanni, Antonio

2015-12-01

The interest in retrofit/rehabilitation of existing concrete structures has increased due to degradation and/or introduction of more stringent design requirements. Among the externally-bonded strengthening systems fiber-reinforced polymers is the most widely known technology. Despite its effectiveness as a material system, the presence of an organic binder has some drawbacks that could be addressed by using in its place a cementitious binder as in fabric-reinforced cementitious matrix (FRCM) systems. The purpose of this paper is to evaluate the behavior of reinforced concrete (RC) beams strengthened in shear with U-wraps made of FRCM. An extensive experimental program was undertaken in order to understand and characterize this composite when used as a strengthening system. The laboratory results demonstrate the technical viability of FRCM for shear strengthening of RC beams. Based on the experimental and analytical results, FRCM increases shear strength but not proportionally to the number of fabric plies installed. On the other hand, FRCM failure modes are related with a high consistency to the amount of external reinforcement applied. Design considerations based on the algorithms proposed by ACI guidelines are also provided.

Impact of Cyclic Loading on Chloride Diffusivity and Mechanical Performance of RC Beams under Seawater Corrosion

Directory of Open Access Journals (Sweden)

Sen Pang

2017-01-01

Full Text Available An experimental study was conducted to investigate the impact of cyclic loading on the mechanical performance and chloride diffusivity of RC beams exposed to seawater wet-dry cycles. To induce initial damage to RC beam specimen, cyclic loading controlled by max load and cycles was applied. Then beam specimens underwent 240 wet-dry cycles of seawater. Results show that the chloride content increased as max load and cycle increased. The chloride content at steel surface increased approximatively linearly as average crack width increased. Moreover, the max load had more influence on chloride content at steel surface than cycle. The difference of average chloride diffusion coefficient between tension and compression concrete was little at uncracked position. Average chloride diffusion coefficient increased as crack width increased when crack width was less than 0.11 mm whereas the increasing tendency was weak when crack width exceeded 0.11 mm. The residual yield load and ultimate load of RC beams decreased as max load and cycle increased. Based on univariate analysis of variance, the max load had more adverse effect on yield load and ultimate load than cycle.

Effects of Calcium Ions on the Thermostability and Spectroscopic Properties of the LH1-RC Complex from a New Thermophilic Purple Bacterium Allochromatium tepidum.

Science.gov (United States)

Kimura, Yukihiro; Lyu, Shuwen; Okoshi, Akira; Okazaki, Koudai; Nakamura, Natsuki; Ohashi, Akira; Ohno, Takashi; Kobayashi, Manami; Imanishi, Michie; Takaichi, Shinichi; Madigan, Michael T; Wang-Otomo, Zheng-Yu

2017-05-18

The light harvesting-reaction center (LH1-RC) complex from a new thermophilic purple sulfur bacterium Allochromatium (Alc.) tepidum was isolated and characterized by spectroscopic and thermodynamic analyses. The purified Alc. tepidum LH1-RC complex showed a high thermostability comparable to that of another thermophilic purple sulfur bacterium Thermochromatium tepidum, and spectroscopic characteristics similar to those of a mesophilic bacterium Alc. vinosum. Approximately 4-5 Ca 2+ per LH1-RC were detected by inductively coupled plasma atomic emission spectroscopy and isothermal titration calorimetry. Upon removal of Ca 2+ , the denaturing temperature of the Alc. tepidum LH1-RC complex dropped accompanied by a blue-shift of the LH1 Q y absorption band. The effect of Ca 2+ was also observed in the resonance Raman shift of the C3-acetyl νC═O band of bacteriochlorophyll-a, indicating changes in the hydrogen-bonding interactions between the pigment and LH1 polypeptides. Thermodynamic parameters for the Ca 2+ -binding to the Alc. tepidum LH1-RC complex indicated that this reaction is predominantly driven by the largely favorable electrostatic interactions that counteract the unfavorable negative entropy change. Our data support a hypothesis that Alc. tepidum may be a transitional organism between mesophilic and thermophilic purple bacteria and that Ca 2+ is one of the major keys to the thermostability of LH1-RC complexes in purple bacteria.

Developing fair compensation structures

International Nuclear Information System (INIS)

Trousdale, W.J.

1998-01-01

The issue of finding an effective way to incorporate Aboriginal values into the process of developing fair compensation structures was discussed. This paper discusses pricing intangible values using dollars, but it was emphasized that 'values' are whatever are important to us. Therefore, in order to achieve fair compensation, creative alternatives that are value-focused should be pursued. In addition to the more straight-forward monetary compensation, compensation could also be about avoiding losses, mitigating adverse impacts, achieving better communication, and promoting cultural understanding. 25 refs., 2 tabs

Some security results of the RC4+ stream cipher

DEFF Research Database (Denmark)

Banik, Subhadeep; Jha, Sonu

2015-01-01

to any even 8-bit constant other than 0xAA. Therefore, the question that naturally arises is whether the design of RC4+ can be protected by fixing the pad parameter to some constant odd value. In this paper, we try to answer this very question. We show that the design is still vulnerable by mounting...... in terms of number of faults required and the computational complexity. In fact, we reduce the number of faults by around 11264 on average, and our algorithm is around 26 times faster....

Interference Cancellation Using Replica Signal for HTRCI-MIMO/OFDM in Time-Variant Large Delay Spread Longer Than Guard Interval

Directory of Open Access Journals (Sweden)

Yuta Ida

2012-01-01

Full Text Available Orthogonal frequency division multiplexing (OFDM and multiple-input multiple-output (MIMO are generally known as the effective techniques for high data rate services. In MIMO/OFDM systems, the channel estimation (CE is very important to obtain an accurate channel state information (CSI. However, since the orthogonal pilot-based CE requires the large number of pilot symbols, the total transmission rate is degraded. To mitigate this problem, a high time resolution carrier interferometry (HTRCI for MIMO/OFDM has been proposed. In wireless communication systems, if the maximum delay spread is longer than the guard interval (GI, the system performance is significantly degraded due to the intersymbol interference (ISI and intercarrier interference (ICI. However, the conventional HTRCI-MIMO/OFDM does not consider the case with the time-variant large delay spread longer than the GI. In this paper, we propose the ISI and ICI compensation methods for a HTRCI-MIMO/OFDM in the time-variant large delay spread longer than the GI.

Homogenized global nonlinear constitutive model for RC panels under cyclic loadings

International Nuclear Information System (INIS)

Huguet, Miquel; Voldoire, Francois; Kotronis, Panagiotis; Erlicher, Silvano

2014-01-01

A new nonlinear stress resultant global constitutive model for RC panels is presented. Concrete damage, concrete stress transfer at cracks and bond-slip stress are the main nonlinear effects identified at the local scale that constitute the basis for the construction of the stress resultant global model through an analytical homogenization technique. The closed form solution is obtained using general functions for the previous phenomena. (authors)

Prestress Loss of CFL in a Prestressing Process for Strengthening RC Beams

Directory of Open Access Journals (Sweden)

Xinyan Guo

2017-01-01

Full Text Available A prestressing system was designed to strengthen reinforced concrete (RC beams with prestressed carbon fiber laminate (CFL. During different prestressing processes, prestress loss was measured using strain gauges attached on the surface of CFL along the length direction. The prestress loss was 50–68% of the whole prestress loss, which is typically associated with CFL slipping between the grip anchors. Approximately 20–27% of the prestress loss was caused by the elastic shortening of the RC beam. An analytical model using linear-elastic theory was constructed to calculate the prestress loss caused by CFL slipping between the anchors and the elastic shortening of the strengthened beams. The compared results showed that the analytical model of prestress loss can describe the experimental data well. Methods of reducing the prestress loss were also suggested. Compared to other experiments, the prestressing system proposed by this research group was effective because the maximum percentage of prestress loss was 14.9% and the average prestress loss was 12.5%.

Experimental study on fatigue crack propagation rate of RC beam strengthened with carbon fiber laminate

Science.gov (United States)

Huang, Peiyan; Liu, Guangwan; Guo, Xinyan; Huang, Man

2008-11-01

The experimental research on fatigue crack propagation rate of reinforced concrete (RC) beams strengthened with carbon fiber laminate (CFL) is carried out by MTS system in this paper. The experimental results show that, the main crack propagation on strengthened beam can be summarized into three phases: 1) fast propagation phase; 2) steady propagation and rest phase; 3) unsteady propagation phase. The phase 2-i.e. steady propagation and rest stage makes up about 95% of fatigue life of the strengthened beam. The propagation rate of the main crack, da/dN, in phase 2 can be described by Paris formula, and the constant C and m can be confirmed by the fatigue crack propagation experiments of the RC beams strengthened with CFL under three-point bending loads.

The response of an RC line MWPC to primary cosmic rays. [Multi-Wire Proportional Counter

Science.gov (United States)

Gregory, J. C.; Selig, W. J.; Austin, R. W.; Derrickson, J. H.; Parnell, T. A.

1978-01-01

A simple 50 x 50 sq cm MWPC plane was arranged as an RC-line and flown on a balloon flight with the MSFC-UAH Cosmic Ray experiment. Positions of primary cosmic ray tracks in the RC-line were determined by the risetime method and compared with the expected position as indicated by a best line fitted through four planes of the conventional MWPC hodoscope. Mean errors were estimated for sea-level muons, and CNO group and iron group particles. It is believed that the delta-rays accompanying the primaries degraded the position resolution. Measured standard deviations allowing for uncertainty in the true track position are of the order of 1 cm or less in the primary charge region between 7 and 26.

Optimizing hybrid spreading in metapopulations.

Science.gov (United States)

Zhang, Changwang; Zhou, Shi; Miller, Joel C; Cox, Ingemar J; Chain, Benjamin M

2015-04-29

Epidemic spreading phenomena are ubiquitous in nature and society. Examples include the spreading of diseases, information, and computer viruses. Epidemics can spread by local spreading, where infected nodes can only infect a limited set of direct target nodes and global spreading, where an infected node can infect every other node. In reality, many epidemics spread using a hybrid mixture of both types of spreading. In this study we develop a theoretical framework for studying hybrid epidemics, and examine the optimum balance between spreading mechanisms in terms of achieving the maximum outbreak size. We show the existence of critically hybrid epidemics where neither spreading mechanism alone can cause a noticeable spread but a combination of the two spreading mechanisms would produce an enormous outbreak. Our results provide new strategies for maximising beneficial epidemics and estimating the worst outcome of damaging hybrid epidemics.

An APETALA2 Homolog, RcAP2, Regulates the Number of Rose Petals Derived From Stamens and Response to Temperature Fluctuations

Directory of Open Access Journals (Sweden)

Yu Han

2018-04-01

Full Text Available Rosa chinensis, which is a famous traditional flower in China, is a major ornamental plant worldwide. Long-term cultivation and breeding have resulted in considerable changes in the number of rose petals, while most wild Rosaceae plants have only one whorl consisting of five petals. The petals of double flowers reportedly originate from stamens, but the underlying molecular mechanism has not been fully characterized. In this study, we observed that the number of petals of R. chinensis ‘Old Blush’ flowers increased and decreased in response to low- and high-temperature treatments, respectively, similar to previous reports. We characterized these variations in further detail and found that the number of stamens exhibited the opposite trend. We cloned an APETALA2 homolog, RcAP2. A detailed analysis of gene structure and promoter cis-acting elements as well as RcAP2 temporospatial expression patterns and responses to temperature changes suggested that RcAP2 expression may be related to the number of petals from stamen origin. The overexpression of RcAP2 in Arabidopsis thaliana transgenic plants may induce the transformation of stamens to petals, thereby increasing the number of petals. Moreover, silencing RcAP2 in ‘Old Blush’ plants decreased the number of petals. Our results may be useful for clarifying the temperature-responsive mechanism involved in petaloid stamen production, which may be relevant for the breeding of new rose varieties with enhanced flower traits.

Flexural repair/strengthening of pre-damaged R.C. beams using embedded CFRP rods

Directory of Open Access Journals (Sweden)

Alaa M. Morsy

2015-12-01

Full Text Available Many reinforced concrete R.C. elements need either strengthening due to the need of increasing the service loads or repair due to overloading stress or environmental deterioration affecting these elements. In this paper an experimental program is presented to investigate the effect of using embedded CFRP rod as NSM reinforcement for strengthening/repairing R.C. beams pre-damaged by loading to different loading levels and comparing the results to those of non-preloaded beams. A total of five beams were cast and six beams were tested under four point loading. The main objective of this paper was to investigate the effect of providing one 12 mm diameter CFRP rod in addition to the existing steel reinforcement. Three beams were tested to failure directly without any preloading, whereas the other three beams were firstly subjected to preloading to different load levels. Following that these three beams were strengthened and were tested up to failure.

Zpracování telemetrických údajů RC modelů letadel

OpenAIRE

Žák, Tomáš

2012-01-01

Bakalářská práce se zaměřuje na problematiku snímání stavu RC modelu letadla, během letu. Je zde detailně rozebrána vnější tak i vnitřní struktura, včetně komunikace. Cílem práce je navrhnutí funkční desky pro snímání stavu RC letadla během letu, k tomu je použita součástka akcelerometr umožňující snímat stav. V digitální podobě je pak následně přeposílá k vyhodnocení do mikrokontroléru. V příloze je uvedeno celkové schéma zapojení včetně seznamu použitých součástek. Bachelor’s project foc...

Flexural Behavior of RC Slabs Strengthened in Flexure with Basalt Fabric-Reinforced Cementitious Matrix

Directory of Open Access Journals (Sweden)

Sugyu Lee

2018-01-01

Full Text Available This paper presents both experimental and analytical research results for predicting the flexural capacity of reinforced concrete (RC slabs strengthened in flexure with basalt fabric-reinforced cementitious matrix (FRCM. A total of 13 specimens were fabricated to evaluate the flexural behavior of RC slabs strengthened with basalt FRCM composite and were tested under four-point loading. The fiber type, tensile reinforcement ratio, and the number of fabric layers were chosen as experimental variables. The maximum load of FRCM-strengthened specimens increased from 11.2% to 98.2% relative to the reference specimens. The energy ratio and ductility of the FRCM-strengthened specimens decreased with the higher amount of fabric and tensile reinforcement. The effective stress level of FRCM fabric can be accurately predicted by a bond strength of ACI 549 and Jung’s model.

Psychometric Properties of the MMPI-2-RF Somatic Complaints (RC1) Scale

Science.gov (United States)

Thomas, Michael L.; Locke, Dona E. C.

2010-01-01

The MMPI-2 Restructured Form (MMPI-2-RF; Tellegen & Ben-Porath, 2008) was designed to be psychometrically superior to its MMPI-2 counterpart. However, the test has yet to be extensively evaluated in diverse clinical settings. The purpose of this study was to examine the psychometric properties of the MMPI-2-RF Somatic Complaints (RC1) scale in…

Seismic reliability assessment of RC structures including soil–structure interaction using wavelet weighted least squares support vector machine

International Nuclear Information System (INIS)

Khatibinia, Mohsen; Javad Fadaee, Mohammad; Salajegheh, Javad; Salajegheh, Eysa

2013-01-01

An efficient metamodeling framework in conjunction with the Monte-Carlo Simulation (MCS) is introduced to reduce the computational cost in seismic reliability assessment of existing RC structures. In order to achieve this purpose, the metamodel is designed by combining weighted least squares support vector machine (WLS-SVM) and a wavelet kernel function, called wavelet weighted least squares support vector machine (WWLS-SVM). In this study, the seismic reliability assessment of existing RC structures with consideration of soil–structure interaction (SSI) effects is investigated in accordance with Performance-Based Design (PBD). This study aims to incorporate the acceptable performance levels of PBD into reliability theory for comparing the obtained annual probability of non-performance with the target values for each performance level. The MCS method as the most reliable method is utilized to estimate the annual probability of failure associated with a given performance level in this study. In WWLS-SVM-based MCS, the structural seismic responses are accurately predicted by WWLS-SVM for reducing the computational cost. To show the efficiency and robustness of the proposed metamodel, two RC structures are studied. Numerical results demonstrate the efficiency and computational advantages of the proposed metamodel for the seismic reliability assessment of structures. Furthermore, the consideration of the SSI effects in the seismic reliability assessment of existing RC structures is compared to the fixed base model. It shows which SSI has the significant influence on the seismic reliability assessment of structures.

A review of the application Acoustic Emission (AE) incorporating mechanical approach to monitor Reinforced concrete (RC) strengthened with Fiber Reinforced Polymer (FRP) properties under fracture

Science.gov (United States)

Syed Mazlan, S. M. S.; Abdullah, S. R.; Shahidan, S.; Noor, S. R. Mohd

2017-11-01

Concrete durability may be affected by so many factors such as chemical attack and weathering action that reduce the performance and the service life of concrete structures. Low durability Reinforced concrete (RC) can be greatly improved by using Fiber Reinforce Polymer (FRP). FRP is a commonly used composite material for repairing and strengthening RC structures. A review on application of Acoustic Emission (AE) techniques of real time monitoring for various mechanical tests for RC strengthened with FRP involving four-point bending, three-point bending and cyclic loading was carried out and discussed in this paper. Correlations between each AE analyses namely b-value, sentry and intensity analysis on damage characterization also been critically reviewed. From the review, AE monitoring involving RC strengthened with FRP using b-value, sentry and intensity analysis are proven to be successful and efficient method in determining damage characterization. However, application of AE analysis using sentry analysis is still limited compared to b-value and intensity analysis in characterizing damages especially for RC strengthened with FRP specimen.

Roles of the spreading scope and effectiveness in spreading dynamics on multiplex networks

Science.gov (United States)

Li, Ming; Liu, Run-Ran; Peng, Dan; Jia, Chun-Xiao; Wang, Bing-Hong

2018-02-01

Comparing with single networks, the multiplex networks bring two main effects on the spreading process among individuals. First, the pathogen or information can be transmitted to more individuals through different layers at one time, which enlarges the spreading scope. Second, through different layers, an individual can also transmit the pathogen or information to the same individuals more than once at one time, which makes the spreading more effective. To understand the different roles of the spreading scope and effectiveness, we propose an epidemic model on multiplex networks with link overlapping, where the spreading effectiveness of each interaction as well as the variety of channels (spreading scope) can be controlled by the number of overlapping links. We find that for Poisson degree distribution, increasing the epidemic scope (the first effect) is more efficient than enhancing epidemic probability (the second effect) to facilitate the spreading process. However, for power-law degree distribution, the effects of the two factors on the spreading dynamics become complicated. Enhancing epidemic probability makes pathogen or rumor easier to outbreak in a finite system. But after that increasing epidemic scopes is still more effective for a wide spreading. Theoretical results along with reasonable explanation for these phenomena are all given in this paper, which indicates that the epidemic scope could play an important role in the spreading dynamics.

RC2S: a cognitive remediation program to improve social cognition in schizophrenia and related disorders

Directory of Open Access Journals (Sweden)

Elodie ePEYROUX

2014-06-01

Full Text Available In people with psychiatric disorders, particularly those suffering from schizophrenia and related illnesses, pronounced difficulties in social interactions are a key manifestation. These difficulties can be partly explained by impairments in social cognition, defined as the ability to understand oneself and others in the social world, which includes abilities such as emotion recognition, theory of mind, attributional style, and social perception and knowledge. The impact of several kinds of interventions on social cognition has been studied recently. The best outcomes in the area of social cognition in schizophrenia are those obtained by way of cognitive remediation programs. New strategies and programs in this line are currently being developed, such as RC2S (Cognitive Remediation of Social Cognition in Lyon, France. Considering that the social cognitive deficits experienced by patients with schizophrenia are very diverse, and that the main objective of social cognitive remediation programs is to improve patients’ functioning in their daily social life, RC2S was developed as an individualized and flexible program that allows patients to practice social interaction in a realistic environment through the use of virtual-reality techniques. In the RC2S program, the patient’s goal is to assist a character named Tom in various social situations. The underlying idea for the patient is to acquire cognitive strategies for analyzing social context and emotional information in order to understand other characters’ mental states and to help Tom manage his social interactions. In this paper, we begin by presenting some data regarding the social cognitive impairments found in schizophrenia and related disorders, and we describe how these deficits are targeted by social cognitive remediation. Then we present the RC2S program and discuss the advantages of computer-based simulation to improve social cognition and social functioning in people with

RC2S: A Cognitive Remediation Program to Improve Social Cognition in Schizophrenia and Related Disorders.

Science.gov (United States)

Peyroux, Elodie; Franck, Nicolas

2014-01-01

In people with psychiatric disorders, particularly those suffering from schizophrenia and related illnesses, pronounced difficulties in social interactions are a key manifestation. These difficulties can be partly explained by impairments in social cognition, defined as the ability to understand oneself and others in the social world, which includes abilities such as emotion recognition, theory of mind (ToM), attributional style, and social perception and knowledge. The impact of several kinds of interventions on social cognition has been studied recently. The best outcomes in the area of social cognition in schizophrenia are those obtained by way of cognitive remediation programs. New strategies and programs in this line are currently being developed, such as RC2S (cognitive remediation of social cognition) in Lyon, France. Considering that the social cognitive deficits experienced by patients with schizophrenia are very diverse, and that the main objective of social cognitive remediation programs is to improve patients' functioning in their daily social life, RC2S was developed as an individualized and flexible program that allows patients to practice social interaction in a realistic environment through the use of virtual reality techniques. In the RC2S program, the patient's goal is to assist a character named Tom in various social situations. The underlying idea for the patient is to acquire cognitive strategies for analyzing social context and emotional information in order to understand other characters' mental states and to help Tom manage his social interactions. In this paper, we begin by presenting some data regarding the social cognitive impairments found in schizophrenia and related disorders, and we describe how these deficits are targeted by social cognitive remediation. Then we present the RC2S program and discuss the advantages of computer-based simulation to improve social cognition and social functioning in people with psychiatric disorders.

RC2S: A Cognitive Remediation Program to Improve Social Cognition in Schizophrenia and Related Disorders

Science.gov (United States)

Peyroux, Elodie; Franck, Nicolas

2014-01-01

In people with psychiatric disorders, particularly those suffering from schizophrenia and related illnesses, pronounced difficulties in social interactions are a key manifestation. These difficulties can be partly explained by impairments in social cognition, defined as the ability to understand oneself and others in the social world, which includes abilities such as emotion recognition, theory of mind (ToM), attributional style, and social perception and knowledge. The impact of several kinds of interventions on social cognition has been studied recently. The best outcomes in the area of social cognition in schizophrenia are those obtained by way of cognitive remediation programs. New strategies and programs in this line are currently being developed, such as RC2S (cognitive remediation of social cognition) in Lyon, France. Considering that the social cognitive deficits experienced by patients with schizophrenia are very diverse, and that the main objective of social cognitive remediation programs is to improve patients’ functioning in their daily social life, RC2S was developed as an individualized and flexible program that allows patients to practice social interaction in a realistic environment through the use of virtual reality techniques. In the RC2S program, the patient’s goal is to assist a character named Tom in various social situations. The underlying idea for the patient is to acquire cognitive strategies for analyzing social context and emotional information in order to understand other characters’ mental states and to help Tom manage his social interactions. In this paper, we begin by presenting some data regarding the social cognitive impairments found in schizophrenia and related disorders, and we describe how these deficits are targeted by social cognitive remediation. Then we present the RC2S program and discuss the advantages of computer-based simulation to improve social cognition and social functioning in people with psychiatric disorders

Optimizing Hybrid Spreading in Metapopulations.

OpenAIRE

Zhang, C.; Zhou, S.; Miller, J. C.; Cox, I. J.; Chain, B. M.

2015-01-01

Epidemic spreading phenomena are ubiquitous in nature and society. Examples include the spreading of diseases, information, and computer viruses. Epidemics can spread by local spreading, where infected nodes can only infect a limited set of direct target nodes and global spreading, where an infected node can infect every other node. In reality, many epidemics spread using a hybrid mixture of both types of spreading. In this study we develop a theoretical framework for studying hybrid epidemic...

Optimizing Hybrid Spreading in Metapopulations

OpenAIRE

Zhang, Changwang; Zhou, Shi; Miller, Joel C.; Cox, Ingemar J.; Chain, Benjamin M.

2014-01-01

Epidemic spreading phenomena are ubiquitous in nature and society. Examples include the spreading of diseases, information, and computer viruses. Epidemics can spread by local spreading, where infected nodes can only infect a limited set of direct target nodes and global spreading, where an infected node can infect every other node. In reality, many epidemics spread using a hybrid mixture of both types of spreading. In this study we develop a theoretical framework for studying hybrid epidemic...

Overview of the divertor design and its integration into RTO/RC-ITER

International Nuclear Information System (INIS)

Janeschitz, G.; Tivey, R.; Antipenkov, A.; Barabash, V.; Chiocchio, S.; Federici, G.; Heidl, H.; Ibbott, C.; Martin, E.

2000-01-01

The design of the divertor and its integration into the reduced technical objectives/reduced cost-international thermonuclear energy reactor (RTO/RC-ITER) is based on the experience gained from the 1998 design of international thermonuclear energy reactor (ITER) and on the research and development performed throughout the engineering design activities (EDA). This paper gives an overview of the layout and functional design of the RTO/RC-ITER divertor, including the integration into the machine and the remote replacement of the divertor cassettes. Design guidelines are presented which have allowed quick preparation of divertor layouts suitable for further study using the B2-EIRENE edge plasma code. As in the 1998 design, the divertor is segmented into cassettes, and the segmentation, which is three per sector, is driven by access through the divertor level ports. Maintaining this access and avoiding interference with poloidal field coils means that the divertor level ports need to be inclined (7 deg.). This opens up the possibility of incorporating inboard and outboard baffles into the divertor cassettes. The cassettes are transported in-vessel by making use of the toroidal rails onto which the cassettes are finally clamped in position. Significant reduction of the space available between the X-point and the vacuum vessel results in re-positioning of the toroidal rails in order to retain sufficient depth for the inner and outer divertor legs. This, in turn, requires some changes to the remote handling (RH) concept. Remote handling (RH) is now based on using a cantilevered articulated gripper during the radial movement of the cassettes inside the RH ports. However, the principle to use a cassette toroidal mover (CTM) for in vessel handling is unchanged, hence maintaining the validity of previous EDA research and development. The space previously left below the cassettes for RH was also used for pumping. Elimination of this space has led to re-siting of the pumping

An Experimental Study on Hybrid Noncompression CF Bracing and GF Sheet Wrapping Reinforcement Method to Restore Damaged RC Structures

Directory of Open Access Journals (Sweden)

Kang Seok Lee

2015-01-01

Full Text Available We describe a novel technique for restoration of reinforced concrete (RC structures that have sustained damage during an earthquake. The reinforcement scheme described here is a hybrid seismic retrofitting technique that combines noncompression X-bracing using CF with externally bonded GF sheets to strengthen RC structures that have sustained damage following an earthquake. The GF sheet is used to improve the ductility of columns, and the noncompression CF X-bracing system, which consists of CF bracing and anchors to replace the conventional steel bracing and bolt connections, is used to increase the lateral strength of the framing system. We report seismic restoration capacity, which enables reuse of the damaged RC frames via the hybrid CF X-bracing and GF sheet wrapping system. Cyclic loading tests were carried out to investigate hysteresis of the lateral load-drift relations, as well as the ductility. The GF sheet significantly improved the ductility of columns, resulting in a change in failure mode. The strengthening effect of conventional CF sheets used in columns is not sufficient with respect to lateral strength and stiffness. However, this study results in a significant increase in the strength of the structure due to the use of CF X-bracing and inhibited buckling failure of the bracing. This result can be exploited to develop guidelines for the application of the reinforcement system to restore damaged RC structures.

IL-17A, IL-17RC polymorphisms and IL17 plasma levels in Tunisian patients with rheumatoid arthritis

Science.gov (United States)

Chahbi, Mayssa; Haouami, Youssra; Sfar, Imen; Abdelmoula, Leila; Ben Abdallah, Taieb; Gorgi, Yousr

2018-01-01

Background Interleukin-17 (IL-17), a cytokine mainly secreted by Th17 cells, seems to play a significant role in the pathogenesis of rheumatoid arthritis (RA). Functional genetic polymorphisms in IL-17 and its receptor genes can influence either qualitatively or quantitatively their functions. Therefore, we aimed to study the impact of IL17-A and IL17RC polymorphisms on plasma level of IL-17 and RA susceptibility and severity. Methods In this context, IL-17A*rs2275913 and IL-17RC*rs708567 polymorphisms were investigated together with the quantification of IL17 plasma level in 115 RA patients and 91 healthy control subjects matched in age, sex and ethnic origin. Results There were no statistically significant associations between IL-17A and IL-17RC studied polymorphisms and RA susceptibility. In contrast, IL-17A plasma levels were significantly higher in patients (55.07 pg/ml) comparatively to controls (4.75 pg/ml), p<10E-12. A ROC curve was used to evaluate the performance of plasma IL-17 in detecting RA. Given 100% specificity, the highest sensitivity of plasma IL-17A was 61.7% at a cut-off value of 18.25 pg/ml; p < 10E-21, CI = [0.849–0.939]. Analytic results showed that the IgM-rheumatoid factor and anti-CCP antibodies were significantly less frequent in patients with the IL-17RC*A/A genotype than those carrying *G/G and *G/A genotypes; p = 0.013 and p = 0.015, respectively. Otherwise, IL-17 plasma levels’ analysis showed a significant association with the activity of RA (DAS28≥5.1 = 74.71 pg/ml vs. DAS28<5.1 = 11.96 pg/ml), p<10E-6. Conclusion IL-17A*rs2275913 (G/A) and IL-17RC*rs708567 (G/A) polymorphisms did not seem to influence RA susceptibility in Tunisian population. This result agrees with those reported previously. Plasma IL-17A level seems to be predictive of severe RA occurrence. PMID:29584788

Regulatory Phosphorylation of Bacterial-Type PEP Carboxylase by the Ca2+-Dependent Protein Kinase RcCDPK1 in Developing Castor Oil Seeds.

Science.gov (United States)

Ying, Sheng; Hill, Allyson T; Pyc, Michal; Anderson, Erin M; Snedden, Wayne A; Mullen, Robert T; She, Yi-Min; Plaxton, William C

2017-06-01

Phosphoenolpyruvate carboxylase (PEPC) is a tightly controlled cytosolic enzyme situated at a crucial branch point of central plant metabolism. In developing castor oil seeds ( Ricinus communis ) a novel, allosterically desensitized 910-kD Class-2 PEPC hetero-octameric complex, arises from a tight interaction between 107-kD plant-type PEPC and 118-kD bacterial-type (BTPC) subunits. The native Ca 2+ -dependent protein kinase (CDPK) responsible for in vivo inhibitory phosphorylation of Class-2 PEPC's BTPC subunit's at Ser-451 was highly purified from COS and identified as RcCDPK1 (XP_002526815) by mass spectrometry. Heterologously expressed RcCDPK1 catalyzed Ca 2+ -dependent, inhibitory phosphorylation of BTPC at Ser-451 while exhibiting: ( i ) a pair of Ca 2+ binding sites with identical dissociation constants of 5.03 μM, ( ii ) a Ca 2+ -dependent electrophoretic mobility shift, and ( iii ) a marked Ca 2+ -independent hydrophobicity. Pull-down experiments established the Ca 2+ -dependent interaction of N-terminal GST-tagged RcCDPK1 with BTPC. RcCDPK1-Cherry localized to the cytosol and nucleus of tobacco bright yellow-2 cells, but colocalized with mitochondrial-surface associated BTPC-enhanced yellow fluorescent protein when both fusion proteins were coexpressed. Deletion analyses demonstrated that although its N-terminal variable domain plays an essential role in optimizing Ca 2+ -dependent RcCDPK1 autophosphorylation and BTPC transphosphorylation activity, it is not critical for in vitro or in vivo target recognition. Arabidopsis ( Arabidopsis thaliana ) CPK4 and soybean ( Glycine max ) CDPKβ are RcCDPK1 orthologs that effectively phosphorylated castor BTPC at Ser-451. Overall, the results highlight a potential link between cytosolic Ca 2+ signaling and the posttranslational control of respiratory CO 2 refixation and anaplerotic photosynthate partitioning in support of storage oil and protein biosynthesis in developing COS. © 2017 American Society of Plant

Distributional effects of flood risk management - a cross-country comparison of preflood compensation

Directory of Open Access Journals (Sweden)

Willemijn J. van Doorn-Hoekveld

2016-12-01

Full Text Available We seek to examine the manner in which either the EU member states of France, the Netherlands, Poland, and Sweden or parts of them, such as the country of England in the UK or the Flemish Region in Belgium, deal with the distributional effects of the flood risk management strategies prevention, defense, and mitigation. Measures carried out in each of these strategies can cause preflood harm, as in the devaluation of property or loss of income. However, different member states and authorities address this harm in different ways. A descriptive overview of the different compensation regimes in the field of flood risk management is followed by an analysis of these differences and an explanation of what may cause them, such as the geographical differences that lead to differences in the way that they interfere with private rights and the dominant legal principles that underlie compensation regimes. An elaborated compensation regime could lead to more equitable and legitimate flood risk management because the burdens are fairly spread and all interests - including those of injured parties - are considered in the decision-making process. Our aim is to stimulate the hardly existent discussion on the financial harm that is caused by measures to prevent floods (preflood, in addition to the already existing discussion on the ex post flood distributional effects.

Status of blanket design for RTO/RC ITER

International Nuclear Information System (INIS)

Yamada, M.; Ioki, K.; Cardella, A.; Elio, F.; Miki, N.

2000-01-01

Design has progressed on the FW/blanket for the RTO/RC (reduced technical objective/ reduced cost) ITER. The basic functions and structures are the same as for the 1998 ITER design. However, design and fabrication methods of the FW/blanket have been improved to achieve ∝ 50% reduction of the construction cost compared to that for the 1998 ITER design. Detailed blanket module designs with flat separable FW panels have been developed to reduce the fabrication cost and the future radioactive waste. Most of the R and D performed so far during the EDA (engineering design activity) is still applicable. Further cost reduction methods are also being investigated and additional R and D is being performed. (orig.)

Evaluation on effects of chloride-induced deterioration on mechanical properties of RC beams with cracking damage

International Nuclear Information System (INIS)

Matsuo, Toyofumi; Matsumura, Takuro; Otsuka, Taku

2015-01-01

This paper discusses the influence of chloride-induced deterioration on mechanical properties of aging reinforced concrete (RC) structures and the applicability of the material degradation model that takes reinforcing steel corrosion into consideration for finite element analysis. We conducted the corrosion tests under the simulated tidal environment and the flexural loading tests for the RC beams with cracking damage and initial defects. Then, the experimental results were numerically correlated to validate the devised modeling. The obtained results were summarized as follows: (a) The cracking damage in specimens caused a minor effect on the reinforcing steel corrosion in the case where the thickness of cover concrete was 40 mm and main rebars did not yield before chloride attack. On the other hand the maximum corrosion ratio of the deteriorated part became considerably larger than that of the non-cracking part in the specimens where the cover concrete were removed partially to simulate spalling by the severe corrosion. (b) Based on the test results, we derived the corrosion velocity of reinforcing steel corresponding to cracking damage degrees. (c) In FEM analyses, we showed that the above modeling can estimate the flexural strength of RC beams in consideration of the degradation in elongation performance of reinforcing steel due to corrosion. (author)

Fuel cycle design evolution from FDR-ITER to RTO/RC-ITER

International Nuclear Information System (INIS)

Murdoch, D.K.; Glugla, M.; Kveton, O.

2000-01-01

Instantaneous fuelling and plasma exhaust flow rates for the reduced technical objective/reduced cost version of International Thermonuclear Experimental Reactor (RTO/RC-ITER) are similar to those described in the Final Design Report (FDR) of ITER, despite the reduction in fusion power by a factor of about two. However, the reduced pulse length and the lower fraction of campaign time spent in burn mode, together with the lower integrated operating lifetime proposed, will generate cost savings in several systems of the fuel cycle. As the quantity of tritium handled per pulse is now smaller, this could be buffered, allowing systems in the tritium plant still to operate in steady state mode as in the FDR design, thereby increasing the potential for downsizing of system capacities. The lower operating time fraction will increase performance margins for some systems, for example, the Torus Exhaust Gas Processing System (TEGPS) which was designed to meet a specified daily release rate for the FDR design conditions which were more onerous than RTO/RC-ITER. As no break through of tritium into cooling water is now expected, the duties of the Water and Atmosphere Detritiation Systems are considerably reduced, and design concepts which are simpler, cheaper and more amenable to modular implementation can be adopted

Options in Compensation

DEFF Research Database (Denmark)

Flor, Christian Riis; Frimor, Hans; Munk, Claus

2014-01-01

We derive the optimal compensation contract in a principal–agent setting in which outcome is used to provide incentives for both effort and risky investments. To motivate investment, optimal compensation entails rewards for high as well as low outcomes, and it is increasing at the mean outcome...

Spread effects - methodology

International Nuclear Information System (INIS)

2004-01-01

Diffusion of technology, environmental effects and rebound effects are the principal effects from the funding of renewable energy and energy economising. It is difficult to estimate the impact of the spread effects both prior to the measures are implemented and after the measures are carried out. Statistical methods can be used to estimate the spread effects, but they are insecure and always need to be complemented with qualitative and subjective evaluations. It is more adequate to evaluate potential spread effects from market and market data surveillance for a selection of technologies and parties. Based on this information qualitative indicators for spread effects can be constructed and used both ex ante and ex post (ml)

RELIABILITY OF LENTICULAR EXPANSION COMPENSATORS

Directory of Open Access Journals (Sweden)

Gabriel BURLACU,

2011-11-01

Full Text Available Axial lenticular compensators are made to take over the longitudinal heat expansion, shock , vibration and noise, made elastic connections for piping systems. In order to have a long life for installations it is necessary that all elements, including lenticular compensators, have a good reliability. This desire can be did by technology of manufactoring and assembly of compensators, the material for lenses and by maintenance.of compensator

Direct displacement-based design of special composite RC shear walls with steel boundary elements

Directory of Open Access Journals (Sweden)

H. Kazemi

2016-06-01

Full Text Available Special composite RC shear wall (CRCSW with steel boundary elements is a kind of lateral force resisting structural system which is used in earthquake-prone regions. Due to their high ductility and energy dissipation, CRCSWs have been widely used in recent years by structural engineers. However, there are few studies in the literature on the seismic design of such walls. Although there are many studies in the literature on the Direct Displacement-Based Design (DDBD of RC structures, however, no study can be found on DDBD of CRCSWs. Therefore, the aim of present study is to evaluate the ability of DDBD method for designing CRCSWs. In this study, four special composite reinforced concrete shear walls with steel boundary elements of 4, 8, 12 and 16 story numbers were designed using the DDBD method for target drift of 2%. The seismic behavior of the four CRCSWs was studied using nonlinear time-history dynamic analyses. Dynamic analyses were performed for the mentioned walls using 7 selected earthquake records. The seismic design parameters considered in this study includes: lateral displacement profile, inelastic dynamic inter-story drift demand, failure pattern and the composite RC shear walls overstrength factor. For each shear wall, the overall overstrength factor was calculated by dividing the ultimate dynamic base shear demand (Vu by the base shear demand (Vd as per the Direct Displacement Based-Design (DDBD method. The results show that the DDBD method can be used to design CRCSWs safely in seismic regions with predicted behavior.

Dynamics model for real time diagnostics of Triga RC-1 system

International Nuclear Information System (INIS)

Gadomski, A.M.; Nanni, V.; Meo, G.

1988-01-01

This paper presents dynamics model of TRIGA RC-1 reactor system. The model is dedicated to the real-time early fault detection during a reactor operation in one week exploitation cycle. The algorithms are specially suited for real-time, long time and also accelerated simulations with assumed diagnostic oriented accuracy. The approximations, modular structure, numerical methods and validation are discussed. The elaborated model will be build in the TRIGA Supervisor System and TRIGA Diagnostic Simulator

Nuclear damage compensation and energy reform

International Nuclear Information System (INIS)

Yokemoto, Masafumi

2013-01-01

Nuclear damage compensation and energy reform were closely related. Nuclear damage compensation cost should be part of generation cost of nuclear power. Extend of nuclear damage compensation was limited by compensation standard of Tokyo Electric Power Co. (TEPCO) following guidelines of Dispute Reconciliation Committee for Nuclear Damage Compensation. TEPCO had already paid compensation of about two trillion yen until now, which was only a part of total damage compensation cost. TEPCO had been provided more than 3.4 trillion yen by Nuclear Damage Liability Facilitation Cooperation, which would be put back by nuclear operators including TEPCO. TEPCO could obtain present raising funds and try to reconstruct business with restart of nuclear power, which might disturb energy reform. Present nuclear damage compensation scheme had better be reformed with learning more from Minamata disease case in Japan. (T. Tanaka)

The FluxCompensator: Making Radiative Transfer Models of Hydrodynamical Simulations Directly Comparable to Real Observations

Science.gov (United States)

Koepferl, Christine M.; Robitaille, Thomas P.

2017-11-01

When modeling astronomical objects throughout the universe, it is important to correctly treat the limitations of the data, for instance finite resolution and sensitivity. In order to simulate these effects, and to make radiative transfer models directly comparable to real observations, we have developed an open-source Python package called the FluxCompensator that enables the post-processing of the output of 3D Monte Carlo radiative transfer codes, such as Hyperion. With the FluxCompensator, realistic synthetic observations can be generated by modeling the effects of convolution with arbitrary point-spread functions, transmission curves, finite pixel resolution, noise, and reddening. Pipelines can be applied to compute synthetic observations that simulate observatories, such as the Spitzer Space Telescope or the Herschel Space Observatory. Additionally, this tool can read in existing observations (e.g., FITS format) and use the same settings for the synthetic observations. In this paper, we describe the package as well as present examples of such synthetic observations.

The FluxCompensator: Making Radiative Transfer Models of Hydrodynamical Simulations Directly Comparable to Real Observations

Energy Technology Data Exchange (ETDEWEB)

Koepferl, Christine M.; Robitaille, Thomas P., E-mail: koepferl@usm.lmu.de [Max Planck Institute for Astronomy, Königstuhl 17, D-69117 Heidelberg (Germany)

2017-11-01

When modeling astronomical objects throughout the universe, it is important to correctly treat the limitations of the data, for instance finite resolution and sensitivity. In order to simulate these effects, and to make radiative transfer models directly comparable to real observations, we have developed an open-source Python package called the FluxCompensator that enables the post-processing of the output of 3D Monte Carlo radiative transfer codes, such as Hyperion. With the FluxCompensator, realistic synthetic observations can be generated by modeling the effects of convolution with arbitrary point-spread functions, transmission curves, finite pixel resolution, noise, and reddening. Pipelines can be applied to compute synthetic observations that simulate observatories, such as the Spitzer Space Telescope or the Herschel Space Observatory . Additionally, this tool can read in existing observations (e.g., FITS format) and use the same settings for the synthetic observations. In this paper, we describe the package as well as present examples of such synthetic observations.

Active rc filter permits easy trade-off of amplifier gain and sensitivity to gain

Science.gov (United States)

Kerwin, W. J.; Shaffer, C. V.

1968-01-01

Passive RC network was designed with zeros of transmission in the right half of the complex frequency plane in the feedback loop of a simple negative-gain amplifier. The proper positioning provides any desired trade-off between amplifier gain and sensitivity to amplifier gain.

Correcting for respiratory motion in liver PET/MRI: preliminary evaluation of the utility of bellows and navigated hepatobiliary phase imaging

International Nuclear Information System (INIS)

Hope, Thomas A.; Verdin, Emily F.; Bergsland, Emily K.; Ohliger, Michael A.; Corvera, Carlos University; Nakakura, Eric K.

2015-01-01

The purpose of this study was to evaluate the utility of bellows-based respiratory compensation and navigated hepatobiliary phase imaging to correct for respiratory motion in the setting of dedicated liver PET/MRI. Institutional review board approval and informed consent were obtained. Six patients with metastatic neuroendocrine tumor were imaged using Ga-68 DOTA-TOC PET/MRI. Whole body imaging and a dedicated 15-min liver PET acquisition was performed, in addition to navigated and breath-held hepatobiliary phase (HBP) MRI. Liver PET data was reconstructed three ways: the entire data set (liver PET), gated using respiratory bellows (RC-liver PET), and a non-gated data set reconstructed using the same amount of data used in the RC-liver PET (shortened liver PET). Liver lesions were evaluated using SUV max , SUV peak , SUV mean , and Vol isocontour . Additionally, the displacement of each lesion between the RC-liver PET images and the navigated and breath-held HBP images was calculated. Respiratory compensation resulted in a 43 % increase in SUVs compared to ungated data (liver vs RC-liver PET SUV max 26.0 vs 37.3, p < 0.001) and a 25 % increase compared to a non-gated reconstruction using the same amount of data (RC-liver vs shortened liver PET SUV max 26.0 vs 32.6, p < 0.001). Lesion displacement was minimized using navigated HBP MRI (1.3 ± 1.0 mm) compared to breath-held HBP MRI (23.3 ± 1.0 mm). Respiratory bellows can provide accurate respiratory compensation when imaging liver lesions using PET/MRI, and results in increased SUVs due to a combination of increased image noise and reduced respiratory blurring. Additionally, navigated HBP MRI accurately aligns with respiratory compensated PET data.

Correcting for respiratory motion in liver PET/MRI: preliminary evaluation of the utility of bellows and navigated hepatobiliary phase imaging

Energy Technology Data Exchange (ETDEWEB)

Hope, Thomas A. [Department of Radiology and Biomedical Imaging, University of California, San Francisco, San Francisco, CA (United States); Department of Radiology, San Francisco VA Medical Center, San Francisco, CA (United States); Verdin, Emily F. [Department of Radiology and Biomedical Imaging, University of California, San Francisco, San Francisco, CA (United States); Bergsland, Emily K. [Division of Hematology/Oncology, Department of Medicine, University of California, San Francisco, San Francisco, CA (United States); Ohliger, Michael A. [Department of Radiology and Biomedical Imaging, University of California, San Francisco, San Francisco, CA (United States); Department of Radiology, San Francisco General Hospital, San Francisco, CA (United States); Corvera, Carlos University; Nakakura, Eric K. [Division of Surgical Oncology, Department of Surgery, University of California, San Francisco, San Francisco, CA (United States)

2015-09-18

The purpose of this study was to evaluate the utility of bellows-based respiratory compensation and navigated hepatobiliary phase imaging to correct for respiratory motion in the setting of dedicated liver PET/MRI. Institutional review board approval and informed consent were obtained. Six patients with metastatic neuroendocrine tumor were imaged using Ga-68 DOTA-TOC PET/MRI. Whole body imaging and a dedicated 15-min liver PET acquisition was performed, in addition to navigated and breath-held hepatobiliary phase (HBP) MRI. Liver PET data was reconstructed three ways: the entire data set (liver PET), gated using respiratory bellows (RC-liver PET), and a non-gated data set reconstructed using the same amount of data used in the RC-liver PET (shortened liver PET). Liver lesions were evaluated using SUV{sub max}, SUV{sub peak}, SUV{sub mean}, and Vol{sub isocontour}. Additionally, the displacement of each lesion between the RC-liver PET images and the navigated and breath-held HBP images was calculated. Respiratory compensation resulted in a 43 % increase in SUVs compared to ungated data (liver vs RC-liver PET SUV{sub max} 26.0 vs 37.3, p < 0.001) and a 25 % increase compared to a non-gated reconstruction using the same amount of data (RC-liver vs shortened liver PET SUV{sub max} 26.0 vs 32.6, p < 0.001). Lesion displacement was minimized using navigated HBP MRI (1.3 ± 1.0 mm) compared to breath-held HBP MRI (23.3 ± 1.0 mm). Respiratory bellows can provide accurate respiratory compensation when imaging liver lesions using PET/MRI, and results in increased SUVs due to a combination of increased image noise and reduced respiratory blurring. Additionally, navigated HBP MRI accurately aligns with respiratory compensated PET data.

Combinatorics of spreads and parallelisms

CERN Document Server

Johnson, Norman

2010-01-01

Partitions of Vector Spaces Quasi-Subgeometry Partitions Finite Focal-SpreadsGeneralizing André SpreadsThe Going Up Construction for Focal-SpreadsSubgeometry Partitions Subgeometry and Quasi-Subgeometry Partitions Subgeometries from Focal-SpreadsExtended André SubgeometriesKantor's Flag-Transitive DesignsMaximal Additive Partial SpreadsSubplane Covered Nets and Baer Groups Partial Desarguesian t-Parallelisms Direct Products of Affine PlanesJha-Johnson SL(2,

Implementation of Highly-Flowable Strain Hardening Fiber Reinforced Concrete in New RC Beam-Column Joints

Directory of Open Access Journals (Sweden)

Liao Wen-Cheng

2018-01-01

Full Text Available The purpose of New RC project was aimed to reduce the member sections and increase the available space of high rise buildings by using high strength concrete (f’c > 70 MPa and high strength rebars (fy > 685 MPa. Material consumptions and member section sizes can be further reduced owing to the upgrade of strength. However, the nature of brittleness of high strength may also cause early cover spalling and other ductility issues. Addition of steel fibers is an alternative as transverse reinforcement. Highly flowable strain hardening fiber reinforced concrete (HF-SHFRC has excellent workability in the fresh state and exhibits the strain-hardening and multiple cracking characteristics of high performance fiber reinforced cementitious composites (HPFRCC in their hardened state. The objective of this study is to investigate the feasibility of implementing HF-SHFRC in New RC building systems, particularly for beam-column joints as an alternative of transverse reinforcements. Four full-scale exterior beam-column joints, including two specimens with intensive transverse reinforcements and two specimens made of HF-SHFRC without any stirrup, are tested. Test results show that the HF-SHFRC specimens perform as well as specimens with intensive transverse reinforcements regarding failure mode, ductility, energy dissipation and crack width control. Integration of New RC building systems and HF-SHFRC can assuring construction qualities and further diminish labor work and give infrastructure longer service life, and eventually lower the life-cycle cost.

48 CFR 970.2270 - Unemployment compensation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to the...

38 CFR 3.351 - Special monthly dependency and indemnity compensation, death compensation, pension and spouse's...

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Special monthly dependency and indemnity compensation, death compensation, pension and spouse's compensation ratings. 3.351 Section 3.351 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension...

Development of a relational database for nuclear material (NM) accounting in RC and I Group

International Nuclear Information System (INIS)

Yadav, M.B.; Ramakumar, K.L.; Venugopal, V.

2011-01-01

A relational database for the nuclear material accounting in RC and I Group has been developed with MYSQL for Back-End and JAVA for Front-End development. Back-End has been developed to avoid any data redundancy, to provide random access of the data and to retrieve the required information from database easily. JAVA Applet and Java Swing components of JAVA programming have been used in the Front-End development. Front-End has been developed to provide data security, data integrity, to generate inventory status report at the end of accounting period, and also to have a quick look of some required information on computer screen. The database has been tested for the data of three quarters of the year 2009. It has been implemented from 1st January, 2010 for the accounting of nuclear material in RC and I Group. (author)

Development of a relational database for nuclear material (NM) accounting in RC and I Group

Energy Technology Data Exchange (ETDEWEB)

Yadav, M B; Ramakumar, K L; Venugopal, V [Radioanalytical Chemistry Division, Radiochemistry and Isotope Group, Bhabha Atomic Research Centre, Mumbai (India)

2011-07-01

A relational database for the nuclear material accounting in RC and I Group has been developed with MYSQL for Back-End and JAVA for Front-End development. Back-End has been developed to avoid any data redundancy, to provide random access of the data and to retrieve the required information from database easily. JAVA Applet and Java Swing components of JAVA programming have been used in the Front-End development. Front-End has been developed to provide data security, data integrity, to generate inventory status report at the end of accounting period, and also to have a quick look of some required information on computer screen. The database has been tested for the data of three quarters of the year 2009. It has been implemented from 1st January, 2010 for the accounting of nuclear material in RC and I Group. (author)

ALGORITMA RC4 DALAM PROTEKSI TRANSMISI DAN HASIL QUERY UNTUK ORDBMS POSTGRESQL

Directory of Open Access Journals (Sweden)

Yuri Ariyanto

2009-01-01

Full Text Available In this research will be worked through about how cryptography RC4's algorithm implementation in protection to query result and of query, security by encryption and descryption up to both is in network. Implementation of this research which is build software in client that function access databases that is placed by the side of server. Software that building to have facility for encryption and descryption query result and of query that is sent from client goes to server and. transmission query result and of query can secure its security. Well guaranted transmission security him of query result and of query can be told to succeed if success software can encryption query result and of query which transmission so that in the event of scanning to both, scanning will not understand data content. Conclusion of this research that is woke up software succeed encryption query and result of query which transmission between application of client and of server databases. Abstract in Bahasa Indonesia: Pada penelitian ini dibahas mengenai bagaimana mengimplementasikan algoritma kriptografi RC4 dalam proteksi terhadap query dan hasil query, pengamanan dilakukan dengan cara melakukan enkripsi dan dekripsi selama keduanya berada di dalam jaringan. Pengimplementasian dari penelitian ini yaitu membangun sebuah software yang akan diletakkan di sisi client yang berfungsi mengakses database yang diletakkan di sisi server. Software yang dibangun memiliki fasilitas untuk mengenkripsi dan mendektipsi query dan hasil query yang dikirimkan dari client ke server dan juga sebaliknya. Dengan demikian tramsmisi query dan hasil query dapat terjamin keamanannya.Terjaminnya keamanan transmisi query dan hasil query dapat dikatakan berhasil jika software berhasil mengenkripsi query dan hasil query yang ditransmisikan sehingga apabila terjadi penyadapan terhadap keduanya, penyadap tidak akan mengerti isi data tersebut. Kesimpulan dari penelitian ini yaitu software yang dibangun

29 CFR 525.6 - Compensable time.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those hours...

Motion-compensated processing of image signals

NARCIS (Netherlands)

2010-01-01

In a motion-compensated processing of images, input images are down-scaled (scl) to obtain down-scaled images, the down-scaled images are subjected to motion- compensated processing (ME UPC) to obtain motion-compensated images, the motion- compensated images are up-scaled (sc2) to obtain up-scaled

Dynamics model for real time diagnostics of TRIGA RC-1 system

International Nuclear Information System (INIS)

Gadomski, A.M.; Nanni, V.; Meo, G.B.

1986-01-01

This paper presents dynamics model of TRIGA RC-1 reactor system. The model is dedicated to the real-time early fault detection during a reactor operation in one week exploitation cycle. The algorithms are specially suited for real-time, long time and also accelerated simulations with assumed diagnostic oriented accuracy. The approximations, modular structure, numerical methods and validation are discussed. The elaborated model will be build in the TRIGA Supervisory System and TRIGA Diagnostic Simulator. (author)

Compensation Consultants and CEO Pay

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Minhat, Marizah

2014-01-01

The study examines the practice of employing multiple compensation consultants. Examining data of a sample of UK companies over the period 2003–2006 we find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant. An increase in the number of compensation

Age, spreading rates, and spreading asymmetry of the world's ocean crust

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The authors present four companion digital models of the age, age uncertainty, spreading rates and spreading asymmetries of the world's ocean basins as geographic...

Modelling loading and break-up of RC structure due to internal explosion of fragmenting shells

NARCIS (Netherlands)

Weerheijm, J.; Stolz, A.; Riedel, W.; Mediavilla Varas, J.

2012-01-01

The Klotz Group (KG), an international group of experts on explosion safety, investigates the debris throw hazard associated with the accidental detonation of ammunition in reinforced concrete (RC-) structures. Experiments are combined with engineering models but also with results of advanced

Modelling loading and break-up of RC structure due to internal explosion of fragmenting shells

NARCIS (Netherlands)

Weerheijm, J.; Stolz, A.; Riedel, W.; Mediavilla, J.

2012-01-01

The Klotz Group (KG), an mtemational group of experts on explosion safety, investigates the debris throw hazard associated with the accidental detonation of ammunition in reinforced concrete (RC-) structures. Experiments are combined with engineering models but also with results of advanced

Automatic error compensation in dc amplifiers

International Nuclear Information System (INIS)

Longden, L.L.

1976-01-01

When operational amplifiers are exposed to high levels of neutron fluence or total ionizing dose, significant changes may be observed in input voltages and currents. These changes may produce large errors at the output of direct-coupled amplifier stages. Therefore, the need exists for automatic compensation techniques. However, previously introduced techniques compensate only for errors in the main amplifier and neglect the errors induced by the compensating circuitry. In this paper, the techniques introduced compensate not only for errors in the main operational amplifier, but also for errors induced by the compensation circuitry. Included in the paper is a theoretical analysis of each compensation technique, along with advantages and disadvantages of each. Important design criteria and information necessary for proper selection of semiconductor switches will also be included. Introduced in this paper will be compensation circuitry for both resistive and capacitive feedback networks

The Intercomparison of 3D Radiation Codes (I3RC): Showcasing Mathematical and Computational Physics in a Critical Atmospheric Application

Science.gov (United States)

Davis, A. B.; Cahalan, R. F.

2001-05-01

The Intercomparison of 3D Radiation Codes (I3RC) is an on-going initiative involving an international group of over 30 researchers engaged in the numerical modeling of three-dimensional radiative transfer as applied to clouds. Because of their strong variability and extreme opacity, clouds are indeed a major source of uncertainty in the Earth's local radiation budget (at GCM grid scales). Also 3D effects (at satellite pixel scales) invalidate the standard plane-parallel assumption made in the routine of cloud-property remote sensing at NASA and NOAA. Accordingly, the test-cases used in I3RC are based on inputs and outputs which relate to cloud effects in atmospheric heating rates and in real-world remote sensing geometries. The main objectives of I3RC are to (1) enable participants to improve their models, (2) publish results as a community, (3) archive source code, and (4) educate. We will survey the status of I3RC and its plans for the near future with a special emphasis on the mathematical models and computational approaches. We will also describe some of the prime applications of I3RC's efforts in climate models, cloud-resolving models, and remote-sensing observations of clouds, or that of the surface in their presence. In all these application areas, computational efficiency is the main concern and not accuracy. One of I3RC's main goals is to document the performance of as wide a variety as possible of three-dimensional radiative transfer models for a small but representative number of ``cases.'' However, it is dominated by modelers working at the level of linear transport theory (i.e., they solve the radiative transfer equation) and an overwhelming majority of these participants use slow-but-robust Monte Carlo techniques. This means that only a small portion of the efficiency vs. accuracy vs. flexibility domain is currently populated by I3RC participants. To balance this natural clustering the present authors have organized a systematic outreach towards

Effects of age and parity on mammary gland lesions and progenitor cells in the FVB/N-RC mice.

Directory of Open Access Journals (Sweden)

Ahmed Raafat

Full Text Available The FVB/N mouse strain is extensively used in the development of animal models for breast cancer research. Recently it has been reported that the aging FVB/N mice develop spontaneous mammary lesions and tumors accompanied with abnormalities in the pituitary glands. These observations have a great impact on the mouse models of human breast cancer. We have developed a population of inbred FVB/N mice (designated FVB/N-RC that have been genetically isolated for 20 years. To study the effects of age and parity on abnormalities of the mammary glands of FVB/N-RC mice, twenty-five nulliparous and multiparous (3-4 pregnancies females were euthanized at 16-22 months of age. Examination of the mammary glands did not reveal macroscopic evidence of mammary gland tumors in either aged-nulliparous or multiparous FVB/N-RC mice (0/25. However, histological analysis of the mammary glands showed rare focal nodules of squamous changes in 2 of the aged multiparous mice. Mammary gland hyperplasia was detected in 8% and 71% of the aged-nulliparous and aged-multiparous mice, respectively. Epithelial contents and serum levels of triiodothyronine were significantly higher in the experimental groups than the 14-wk-old control mice. Immuno-histochemical staining of the pituitary gland pars distalis showed no difference in prolactin staining between the control and the aged mice. Tissue transplant and dilution studies showed no effect of age and/or parity on the ability of putative progenitor cells present among the injected mammary cells to repopulate a cleared fat pad and develop a full mammary gland outgrowth. This FVB/N-RC mouse substrain is suitable to develop mouse models for breast cancer.

Overview and evolution of the LeRC PMAD DC test bed

Science.gov (United States)

Soeder, James F.; Frye, Robert J.

1992-01-01

Since the beginning of the Space Station Freedom Program (SSFP), the Lewis Research Center (LeRC) has been developed electrical power system test beds to support the overall design effort. Through this time, the SSFP has changed the design baseline numerous times, however, the test bed effort has endeavored to track these changes. Beginning in August 1989 with the baseline and an all DC system, a test bed was developed to support the design baseline. The LeRC power measurement and distribution (PMAD) DC test bed and the changes in the restructure are described. The changes included the size reduction of primary power channel and various power processing elements. A substantial reduction was also made in the amount of flight software with the subsequent migration of these functions to ground control centers. The impact of these changes on the design of the power hardware, the controller algorithms, the control software, and a description of their current status is presented. An overview of the testing using the test bed is described, which includes investigation of stability and source impedance, primary and secondary fault protection, and performance of a rotary utility transfer device. Finally, information is presented on the evolution of the test bed to support the verification and operational phases of the SSFP in light of these restructure scrubs.

The Nature of Whiplash in a Compensable Environment: Injury, Disability, Rehabilitation, and Compensation Systems.

Science.gov (United States)

Connelly, Luke B

2017-07-01

Synopsis Whiplash is a compensable injury in many jurisdictions, but there is considerable heterogeneity in the compensation arrangements that apply across jurisdictions, even within some countries. These compensation schemes have, however, been subject to a common set of interrelated concerns, chiefly concerning the incentives, behaviors, and outcomes that may arise when financial compensation for injuries is available to injured parties. This article provides a nontechnical overview of some of those concerns through the lens of economics: principally, insurance economics and health economics, including related subsets such as information economics and agency theory, as well as economics and the law. It notes that because it is generally infeasible to randomize the treatment (ie, compensation) via trials, analyses of observational data are necessary to discover more about the relationship between compensation and health outcomes. This poses the analytical challenge of discovering causal connections between phenomena from nonrandomized data sets. The present article calls for further research that would enable convincing causal interpretations of such relationships via the careful analysis of rich observational data sets using modern econometric methods. J Orthop Sports Phys Ther 2017;47(7):503-508. Epub 16 Jun 2017. doi:10.2519/jospt.2017.7533.

A primer for workers' compensation.

Science.gov (United States)

Bible, Jesse E; Spengler, Dan M; Mir, Hassan R

2014-07-01

A physician's role within a workers' compensation injury extends far beyond just evaluation and treatment with several socioeconomic and psychological factors at play compared with similar injuries occurring outside of the workplace. Although workers' compensation statutes vary among states, all have several basic features with the overall goal of returning the injured worker to maximal function in the shortest time period, with the least residual disability and shortest time away from work. To help physicians unfamiliar with the workers' compensation process accomplish these goals. Review. Educational review. The streamlined review addresses the topics of why is workers' compensation necessary; what does workers' compensation cover; progression after work injury; impairment and maximum medical improvement, including how to use the sixth edition of American Medical Association's (AMA) Guides to the evaluation of permanent impairment (Guides); completion of work injury claim after impairment rating; independent medical evaluation; and causation. In the "no-fault" workers' compensation system, physicians play a key role in progressing the claim along and, more importantly, getting the injured worker back to work as soon as safely possible. Physicians should remain familiar with the workers' compensation process, along with how to properly use the AMA Guides. Copyright © 2014 Elsevier Inc. All rights reserved.

Financial protection of patients through compensation of providers: the impact of Health Equity Funds in Cambodia.

Science.gov (United States)

Flores, Gabriela; Ir, Por; Men, Chean R; O'Donnell, Owen; van Doorslaer, Eddy

2013-12-01

Public providers have no financial incentive to respect their legal obligation to exempt the poor from user fees. Health Equity Funds (HEFs) aim to make exemptions effective by giving NGOs responsibility for assessing eligibility and compensating providers for lost revenue. We use the geographic spread of HEFs over time in Cambodia to identify their impact on out-of-pocket (OOP) payments. Among households with some OOP payment, HEFs reduce the amount paid by 35%, on average. The effect is larger for households that are poorer and mainly use public health care. Reimbursement of providers through a government operated scheme also reduces household OOP payments but the effect is not as well targeted on the poor. Both compensation models raise household non-medical consumption but have no impact on health-related debt. HEFs reduce the probability of primarily seeking care in the private sector. Copyright © 2013 Elsevier B.V. All rights reserved.

Loads experiments study on two-story RC box and truncated conical walls

International Nuclear Information System (INIS)

Asega, H.; Iizuka, S.; Kurihara, I.; Kubo, T.

1987-01-01

The failure modes of the two specimens were the sliding shear failure. The two specimens showed almost equal deformation at the maximum shear strength. The ratio of the flexural deformation in the deformation of the truncated conical was larger than that of the box wall. The ratio of the shear deformation in the deformation of the two-story RC box wall was larger than that of the flexural deformation. (orig./HP)

42 CFR 413.102 - Compensation of owners.

Science.gov (United States)

2010-10-01

...) Definitions—(1) Compensation. Compensation means the total benefit received by the owner for the services he... 42 Public Health 2 2010-10-01 2010-10-01 false Compensation of owners. 413.102 Section 413.102... § 413.102 Compensation of owners. (a) Principle. A reasonable allowance of compensation for services of...

NoRC Recruitment by H2A.X Deposition at rRNA Gene Promoter Limits Embryonic Stem Cell Proliferation

Directory of Open Access Journals (Sweden)

Boris Eleuteri

2018-05-01

Full Text Available Summary: Embryonic stem cells (ESCs display an abbreviated cell cycle, resulting in a short doubling time and rapid proliferation. The histone variant H2A.X is critical for proliferation of stem cells, although mechanistic insights have remained obscure. Here, we show that H2A.X defines the rate of mouse ESC proliferation independently of the DNA damage response pathway, and it associates with three major chromatin-modifying complexes. Our functional and biochemical analyses demonstrate that H2A.X-associated factors mediate the H2A.X-dependent effect on ESC proliferation and involve the nucleolar remodeling complex (NoRC. A specific H2A.X deposition at rDNA promoters determines the chromatin recruitment of the NoRC, histone modifications, the rRNA transcription, and the rate of proliferation. Collectively, our results suggest that NoRC assembly by H2A.X deposition at rRNA promoters silences transcription, and this represents an important regulatory component for ESC proliferation. : Histone variant H2A.X defines the rate of embryonic stem cell proliferation. Eleuteri et al. identify H2A.X-interacting proteins, and they show that H2A.X deposition at rDNA promoters assembles the NoRC, which represses rRNA transcription and determines the rate of self-renewal. Keywords: ribosomal biogenesis, rRNA, rDNA, stem cells, TIP5, SNF2H, SPT16, BRG1, H2A.X, G1, cell cycle, cell cycle arrest, proliferation

Fat type in phytosterol products influence their cholesterol-lowering potential: A systematic review and meta-analysis of RCTs.

Science.gov (United States)

Ferguson, Jessica J A; Stojanovski, Elizabeth; MacDonald-Wicks, Lesley; Garg, Manohar L

2016-10-01

The most common form of phytosterol (PS) fortified foods are fat spreads and dairy products. The predominant fats used are soybean/sunflower (SS) or rapeseed/canola (RC) oils and animal fat (D) in dairy products. This review aimed to investigate whether the carrier fat is a determinant of the hypocholesterolaemic effects of PS fortified foods. Databases were searched using relevant keywords and published RCTs from 1990 investigating the effects of dietary PS intervention (≥1.5g per day) on total cholesterol and LDL-C were included. After methodological quality assessment and data extraction, a total of 32 RCTs (RC, n=15; SS, n=9; D, n=8) were included. As expected, all fat groups significantly reduced TC and LDL-C (p<0.01). When compared across different carrier fats, RC as the main carrier fat, reduced LDL-C significantly more than the SS spreads (p=0.01). Therefore, a combination of monounsaturated fatty acid rich spread with adequate amounts of omega-3 fatty acids (as evident in RC spreads) may be the superior carrier fat for the delivery of PS for optimal blood cholesterol-lowering. The findings of this research provide useful evidence for optimising the hypocholesterolaemic effects of PS and support further investigation into the possible mechanisms behind these findings. Copyright © 2016 Elsevier B.V. All rights reserved.

The VULCANO spreading programme

Energy Technology Data Exchange (ETDEWEB)

Cognet, G.; Laffont, G.; Jegou, C.; Journeau, C.; Sudreau, F.; Pierre, J.; Ramacciotti, M. [CEA (Atomic Energy Commission), DRN/DER - Bat. 212, CEA Cadarache, 13108 St. Paul Lez Durance (France)

1999-07-01

Among the currently studied core-catcher projects, some of them suppose corium spreading before cooling, in particular the EPR (European Pressurized Reactor) core-catcher concept is based on mixing the corium with a special concrete, spreading the molten mixture on a large multi-layer surface cooled from the bottom and subsequently cooling by flooding with water. Therefore, melt spreading deserves intensive investigation in order to determine and quantify key phenomena which govern the stopping of spreading. In France, for some years, the Nuclear Reactor Division of the Atomic Energy Commission (CEA/DRN) has undertaken a large program to improve knowledge on corium behaviour and coolability. This program is based on experimental and theoretical investigations which are finally gathered in scenario and mechanistic computer codes. In this framework, the real material experimental programme, VULCANO, conducted within an European frame, is currently devoted to the study of corium spreading. In 1997 and 1998, several tests have been performed on dry corium spreading with various composition of melts. Although all the observed phenomena, in particular the differences between simulant and real material melts have not been yet totally explained, these tests have already provided a lot of information about: The behaviour of complex mixtures including refractory oxides, silica, iron oxides and in one case iron metal; Spreading progression, which was never stopped in any of these tests by a crust formation at the front; The structure of spread melts (porosity, crusts,...); Physico-chemical interaction between melt and the refractory substratum which was composed of zirconia bricks. (authors)

The VULCANO spreading programme

International Nuclear Information System (INIS)

Cognet, G.; Laffont, G.; Jegou, C.; Journeau, C.; Sudreau, F.; Pierre, J.; Ramacciotti, M.

1999-01-01

Among the currently studied core-catcher projects, some of them suppose corium spreading before cooling, in particular the EPR (European Pressurized Reactor) core-catcher concept is based on mixing the corium with a special concrete, spreading the molten mixture on a large multi-layer surface cooled from the bottom and subsequently cooling by flooding with water. Therefore, melt spreading deserves intensive investigation in order to determine and quantify key phenomena which govern the stopping of spreading. In France, for some years, the Nuclear Reactor Division of the Atomic Energy Commission (CEA/DRN) has undertaken a large program to improve knowledge on corium behaviour and coolability. This program is based on experimental and theoretical investigations which are finally gathered in scenario and mechanistic computer codes. In this framework, the real material experimental programme, VULCANO, conducted within an European frame, is currently devoted to the study of corium spreading. In 1997 and 1998, several tests have been performed on dry corium spreading with various composition of melts. Although all the observed phenomena, in particular the differences between simulant and real material melts have not been yet totally explained, these tests have already provided a lot of information about: The behaviour of complex mixtures including refractory oxides, silica, iron oxides and in one case iron metal; Spreading progression, which was never stopped in any of these tests by a crust formation at the front; The structure of spread melts (porosity, crusts,...); Physico-chemical interaction between melt and the refractory substratum which was composed of zirconia bricks. (authors)

Regulatory Phosphorylation of Bacterial-Type PEP Carboxylase by the Ca2+-Dependent Protein Kinase RcCDPK1 in Developing Castor Oil Seeds1[OPEN

Science.gov (United States)

Hill, Allyson T.; Anderson, Erin M.; She, Yi-Min

2017-01-01

Phosphoenolpyruvate carboxylase (PEPC) is a tightly controlled cytosolic enzyme situated at a crucial branch point of central plant metabolism. In developing castor oil seeds (Ricinus communis) a novel, allosterically desensitized 910-kD Class-2 PEPC hetero-octameric complex, arises from a tight interaction between 107-kD plant-type PEPC and 118-kD bacterial-type (BTPC) subunits. The native Ca2+-dependent protein kinase (CDPK) responsible for in vivo inhibitory phosphorylation of Class-2 PEPC’s BTPC subunit’s at Ser-451 was highly purified from COS and identified as RcCDPK1 (XP_002526815) by mass spectrometry. Heterologously expressed RcCDPK1 catalyzed Ca2+-dependent, inhibitory phosphorylation of BTPC at Ser-451 while exhibiting: (i) a pair of Ca2+ binding sites with identical dissociation constants of 5.03 μM, (ii) a Ca2+-dependent electrophoretic mobility shift, and (iii) a marked Ca2+-independent hydrophobicity. Pull-down experiments established the Ca2+-dependent interaction of N-terminal GST-tagged RcCDPK1 with BTPC. RcCDPK1-Cherry localized to the cytosol and nucleus of tobacco bright yellow-2 cells, but colocalized with mitochondrial-surface associated BTPC-enhanced yellow fluorescent protein when both fusion proteins were coexpressed. Deletion analyses demonstrated that although its N-terminal variable domain plays an essential role in optimizing Ca2+-dependent RcCDPK1 autophosphorylation and BTPC transphosphorylation activity, it is not critical for in vitro or in vivo target recognition. Arabidopsis (Arabidopsis thaliana) CPK4 and soybean (Glycine max) CDPKβ are RcCDPK1 orthologs that effectively phosphorylated castor BTPC at Ser-451. Overall, the results highlight a potential link between cytosolic Ca2+ signaling and the posttranslational control of respiratory CO2 refixation and anaplerotic photosynthate partitioning in support of storage oil and protein biosynthesis in developing COS. PMID:28363991

Deformation compensation in dynamic tomography; Compensation de deformations en tomographie dynamique

Energy Technology Data Exchange (ETDEWEB)

Desbat, L. [Universite Joseph Fourier, UMR CNRS 5525, 38 - Grenoble (France); Roux, S. [Universite Joseph Fourier, TIMC-IMAG, In3S, Faculte de Medecine, 38 - Grenoble (France)]|[CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France); Grangeat, P. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France)

2005-07-01

This work is a contribution to the compensation of motion in tomography. New classes of deformation are proposed, that compensates analytically by an algorithm of a F.B.P. type reconstruction. This work makes a generalisation of the known results for affine deformations, in parallel geometry and fan-beam, to deformation classes of infinite dimension able to include strong non linearities. (N.C.)

Full Scale RC Beam-Column Joints Strengthened with Steel Reinforced Polymer Systems

Science.gov (United States)

De Vita, Alessandro; Napoli, Annalisa; Realfonzo, Roberto

2017-07-01

This paper presents the results of an experimental campaign performed at the Laboratory of Materials and Structural Testing of the University of Salerno (Italy) in order to investigate the seismic performance of RC beam-column joints strengthened with Steel Reinforced Polymer (SRP) systems. With the aim to represent typical façade frames’ beam-column subassemblies found in existing RC buildings, specimens were provided with two short beam stubs orthogonal to the main beam and were designed with inadequate seismic details. Five members were strengthened by using two different SRP layouts while the remaining ones were used as benchmarks. Once damaged, two specimens were also repaired, retrofitted with SRP and subjected to cyclic test again. The results of cyclic tests performed on SRP strengthened joints are examined through a comparison with the outcomes of the previous experimental program including companion specimens not provided with transverse beam stubs and strengthened by Carbon Fiber Reinforced Polymer (CFRP) systems. In particular, both qualitative and quantitative considerations about the influence of the confining effect provided by the secondary beams on the joint response, the suitability of all the adopted strengthening solutions (SRP/CFRP systems), the performances and the failure modes experienced in the several cases studied are provided.

Asbestos-related occupational cancers compensated under the Industrial Accident Compensation Insurance in Korea.

Science.gov (United States)

Ahn, Yeon-Soon; Kang, Seong-Kyu

2009-04-01

Compensation for asbestos-related cancers occurring in occupationally-exposed workers is a global issue; this is also an issue in Korea. To provide basic information regarding compensation for workers exposed to asbestos, 60 cases of asbestos-related occupational lung cancer and mesothelioma that were compensated during 15 yr; from 1993 (the year the first case was compensated) to 2007 by the Korea Labor Welfare Corporation (KLWC) are described. The characteristics of the cases were analyzed using the KLWC electronic data and the epidemiologic investigation data conducted by the Occupational Safety and Health Research Institute (OSHRI) of the Korea Occupational Safety and Health Agency (KOSHA). The KLWC approved compensation for 41 cases of lung cancer and 19 cases of mesothelioma. Males accounted for 91.7% (55 cases) of the approved cases. The most common age group was 50-59 yr (45.0%). The mean duration of asbestos exposure for lung cancer and mesothelioma cases was 19.2 and 16.0 yr, respectively. The mean latency period for lung cancer and mesothelioma cases was 22.1 and 22.6 yr, respectively. The major industries associated with mesothelioma cases were shipbuilding and maintenance (4 cases) and manufacture of asbestos textiles (3 cases). The major industries associated with lung cancer cases were shipbuilding and maintenance (7 cases), construction (6 cases), and manufacture of basic metals (4 cases). The statistics pertaining to asbestos-related occupational cancers in Korea differ from other developed countries in that more cases of mesothelioma were compensated than lung cancer cases. Also, the mean latency period for disease onset was shorter than reported by existing epidemiologic studies; this discrepancy may be related to the short history of occupational asbestos use in Korea. Considering the current Korean use of asbestos, the number of compensated cases in Korea is expected to increase in the future but not as much as developed countries.

Damage Localization of Severely Damaged RC-Structures Based on Measured Eigenperiods from a Single Response

DEFF Research Database (Denmark)

Skjærbæk, P. S.; Nielsen, Søren R.K.; Cakmak, A. S.

This paper deals with the estimation of the damage location of severely damaged Reinforced Concrete (RC) structures excited by earthquakes. It is assumed that the building is instrumented with a sensor measuring the earthquake acceleration signal at ground surface and a sensor measuring only...

FW/Blanket and vacuum vessel for RTO/RC ITER

International Nuclear Information System (INIS)

Ioki, K.; Barabash, V.; Cardella, A.; Elio, F.; Iida, H.; Johnson, G.; Kalinin, G.; Miki, N.; Onozuka, M.; Sannazzaro, G.; Utin, Y.; Yamada, M.

2000-01-01

The design has progressed on the vacuum vessel and First Wall (FW)/blanket for the Reduced Technical Objective/Reduced Cost (RTO/RC) ITER. The basic functions and structures are the same as for the 1998 ITER design. The design has been improved to achieve, along with the size reduction, ∼50% target reduction of the fabrication cost. The number of blanket modules has been minimized according to smaller dimensions of the machine and a higher payload capacity of the blanket Remote Handling tool. A concept without the back plate has been designed and assessed. The blanket module concept with flat separable FW panels has been developed to reduce the fabrication cost and future radioactive waste

FW/Blanket and vacuum vessel for RTO/RC ITER

Energy Technology Data Exchange (ETDEWEB)

Ioki, K. E-mail: iokik@itereu.de; Barabash, V.; Cardella, A.; Elio, F.; Iida, H.; Johnson, G.; Kalinin, G.; Miki, N.; Onozuka, M.; Sannazzaro, G.; Utin, Y.; Yamada, M

2000-11-01

The design has progressed on the vacuum vessel and First Wall (FW)/blanket for the Reduced Technical Objective/Reduced Cost (RTO/RC) ITER. The basic functions and structures are the same as for the 1998 ITER design. The design has been improved to achieve, along with the size reduction, {approx}50% target reduction of the fabrication cost. The number of blanket modules has been minimized according to smaller dimensions of the machine and a higher payload capacity of the blanket Remote Handling tool. A concept without the back plate has been designed and assessed. The blanket module concept with flat separable FW panels has been developed to reduce the fabrication cost and future radioactive waste.

SOIL STRUCTURE INTERACTION EFFECTS ON MULTISTOREY R/C STRUCTURES

Directory of Open Access Journals (Sweden)

Muberra ESER AYDEMIR

2013-01-01

Full Text Available This paper addresses the behavior of multistorey structures considering soil structure interaction under earthquake excitation. For this purpose, sample 3, 6, 9 storey RC frames are designed based on Turkish Seismic Design Code and analyzed in time domain with incremental dynamic analysis. Strength reduction factors are investigated for generated sample plane frames for 64 different earthquake motions recorded on different site conditions such as rock, stiff soil, soft soil and very soft soil. According to the analysis result, strength reduction factors of sample buildings considering soil structure interaction are found to be almost always smaller than design strength reduction factors given in current seismic design codes, which cause an unsafe design and nonconservative design forces.

A higher risk of acute rejection of human kidney allografts can be predicted from the level of CD45RC expressed by the recipients' CD8 T cells.

Directory of Open Access Journals (Sweden)

Laurence Ordonez

Full Text Available Although transplantation is the common treatment for end-stage renal failure, allograft rejection and marked morbidity from the use of immunosuppressive drugs remain important limitations. A major challenge in the field is to identify easy, reliable and noninvasive biomarkers allowing the prediction of deleterious alloreactive immune responses and the tailoring of immunosuppressive therapy in individuals according to the rejection risk. In this study, we first established that the expression of the RC isoform of the CD45 molecule (CD45RC on CD4 and CD8 T cells from healthy individuals identifies functionally distinct alloreactive T cell subsets that behave differently in terms of proliferation and cytokine secretion. We then investigated whether the frequency of the recipients CD45RC T cell subsets before transplantation would predict acute graft rejection in a cohort of 89 patients who had undergone their first kidney transplantation. We showed that patients exhibiting more than 54.7% of CD8 CD45RC(high T cells before transplantation had a 6 fold increased risk of acute kidney graft rejection. In contrast, the proportions of CD4 CD45RC T cells were not predictive. Thus, a higher risk of acute rejection of human kidney allografts can be predicted from the level of CD45RC expressed by the recipients' CD8 T cells.

3D FE Analysis of RC Beams Externally Strengthened with SRG/SRP Systems

Directory of Open Access Journals (Sweden)

Francesco Bencardino

2016-05-01

Full Text Available The purpose of this study is to evaluate, through a nonlinear Finite Element (FE analysis, the structural behavior of Reinforced Concrete (RC beams externally strengthened by using Steel Reinforced Grout (SRG and Steel Reinforced Polymer (SRP systems. The parameters taken into account were the external strengthening configuration, with or without U-wrap end anchorages, as well as the strengthening materials. The numerical simulations were carried out by using a three-dimensional (3D FE model. The linear and nonlinear behavior of all materials was modeled by appropriate constitutive laws and the connection between concrete substrate and external reinforcing layer was simulated by means of cohesive surfaces with appropriate bond-slip laws. In order to overcome convergence difficulties, to simulate the quasi-static response of the strengthened RC beams, a dynamic approach was adopted. The numerical results in terms of load-displacement curves, failure modes, and load and strain values at critical stages were validated against some experimental data. As a result, the proposed 3D FE model can be used to predict the structural behavior up to ultimate stage of similar strengthened beams without carrying out experimental tests.

Quasistatic Seismic Damage Indicators for RC Structures from Dissipating Energies in Tangential Subspaces

Directory of Open Access Journals (Sweden)

Wilfried B. Krätzig

2014-01-01

Full Text Available This paper applies recent research on structural damage description to earthquake-resistant design concepts. Based on the primary design aim of life safety, this work adopts the necessity of additional protection aims for property, installation, and equipment. This requires the definition of damage indicators, which are able to quantify the arising structural damage. As in present design, it applies nonlinear quasistatic (pushover concepts due to code provisions as simplified dynamic design tools. Substituting so nonlinear time-history analyses, seismic low-cycle fatigue of RC structures is approximated in similar manner. The treatment will be embedded into a finite element environment, and the tangential stiffness matrix KT in tangential subspaces then is identified as the most general entry for structural damage information. Its spectra of eigenvalues λi or natural frequencies ωi of the structure serve to derive damage indicators Di, applicable to quasistatic evaluation of seismic damage. Because det KT=0 denotes structural failure, such damage indicators range from virgin situation Di=0 to failure Di=1 and thus correspond with Fema proposals on performance-based seismic design. Finally, the developed concept is checked by reanalyses of two experimentally investigated RC frames.

Scientific Performance Analysis of the SYZ Telescope Design versus the RC Telescope Design

Science.gov (United States)

Ma, Donglin; Cai, Zheng

2018-02-01

Recently, Su et al. propose an innovative design, referred as the “SYZ” design, for China’s new project of a 12 m optical-infrared telescope. The SYZ telescope design consists of three aspheric mirrors with non-zero power, including a relay mirror below the primary mirror. SYZ design yields a good imaging quality and has a relatively flat field curvature at Nasmyth focus. To evaluate the science-compatibility of this three-mirror telescope, in this paper, we thoroughly compare the performance of SYZ design with that of Ritchey–Chrétien (RC) design, a conventional two-mirror telescope design. Further, we propose the Observing Information Throughput (OIT) as a metric for quantitatively evaluating the telescopes’ science performance. We find that although a SYZ telescope yields a superb imaging quality over a large field of view, a two-mirror (RC) telescope design holds a higher overall throughput, a better diffraction-limited imaging quality in the central field of view (FOV < 5‧) which is better for the performance of extreme Adaptive Optics (AO), and a generally better scientific performance with a higher OIT value. D. Ma & Z. Cai contributed equally to this paper.

Effect of CFRP and TRM Strengthening of RC Slabs on Punching Shear Strength

Directory of Open Access Journals (Sweden)

Husain Abbas

Full Text Available Abstract The paper presents experiments involving punching of RC slabs strengthened using externally bonded carbon fiber reinforced polymer (CFRP sheet and textile reinforced mortar (TRM. Twelve RC slab specimens of two concrete grades (39.9 and 63.2 MPa and employing two strengthening schemes (CFRP and TRM were tested. Specimens were supported on two opposite edges. Experimental load-displacement variations show two peak loads in strengthened slabs and one peak followed by a plateau in control. Second peak or the plateau corresponds to the combined action of aggregate interlock and the dowel action of back face rebars and strengthening layers. The dowel action of back face rebars and strengthening layers had no role in ultimate punching load (i.e. first peak. Strengthened slabs showed 9-18% increase in ultimate punching load (i.e. first peak whereas there was significant increase in the second peak load (190-276% for CFRP; 55-136% for TRM and energy absorption (~66% for CFRP and 22-56% for TRM. An analytical model was also developed for predicting the punching shear strength (first and second peaks of strengthened slabs showing good comparison with experiments.

Cooperation, compensation and transition

NARCIS (Netherlands)

Ju, Y.

2004-01-01

Cooperation and compensation are two important and well-linked issues in economics. The central question in cooperation is how to share the joint gains among participating players. Compensation is a specific aspect of surplus sharing problems providing incentives for agents to sacrifice their own

Identification Report: Earthquake Test on 2-Bay, 6-Story Scale 1:5 RC-Frames

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Skjærbæk, P. S.; Nielsen, Søren R. K.

The aim of the present report is to supply the identification results from the tests performed with a laboratory model of a plane 6-storey, 2-bay scale 1:5 RC-frame at Aalborg University, Denmark during the autumn 1996. The tests were performed as a part of a Ph.D study considering evaluation of ...

How to avoid deferred-compensation troubles.

Science.gov (United States)

Freeman, Todd I

2005-06-01

Executive compensation packages have long included stock options and deferred compensation plans in order to compete for talent. Last year, Congress passed a law in response to the Enron debacle, in which executives were perceived to be protecting their deferred compensation at the expense of employees, creditors, and investors. The new law is designed to protect companies and their shareholders from being raided by the very executives that guided the company to financial ruin. Physicians who are part owners of medical practices need to know about the changes in the law regarding deferred compensation and how to avoid costly tax penalties. This article discusses how the changes affect medical practices as well as steps physician-owned clinics can take to avoid the risk of penalty, such as freezing deferred compensation and creating a new deferred compensation plan.

Interim report on intrathoracic radiotherapy of human small-cell lung carcinoma in nude mice with Re-188-RC-160, a radiolabeled somatostatin analogue

International Nuclear Information System (INIS)

Zamora, P.O.; Bender, H.; Biersack, H.J.; Knapp, F.F. Jr.

1995-01-01

The purpose of this study was to evaluate the therapeutic efficacy of Re-188-RC-160 in experimental models of human small cell lung carcinomas which mimic the clinical presentation. In the experimental model, cells from the human small cell lung carcinoma cell line NCI-H69 cells were inoculated into the thoracic cavity of athymic mice and rats. Subsequently, the biodistribution of Re-188-RC-160 after injection into the pleural cavity, a radiolabeled somatostatin analogue, was monitored as was the effect on the subsequent growth of tumors. The results presented here, and which are a part of a larger series of studies, suggest that Re-188-RC-160 can be effectively used in this animal model to restrict the growth of small cell lung carcinoma in the thoracic cavity

Prediction of RC multi-story construction performance with a new proposed design spectrum approach

Directory of Open Access Journals (Sweden)

James Haido

2016-02-01

Full Text Available The consideration of novel response spectrum analysis to check the reinforced concrete RC buildings resistance towards the seismic risks in Iraq has not been investigated so far. Due to the increasing of frequent earthquakes with moderate intensity in north of Iraq, caution should be taken into account in building design especially with considering the design codes. Where, there are no specific Iraqi standards of earthquake for building design. Thus, the proposing of new response spectrum relationship matching the properties of Kurdistan region (north of Iraq soil is considered essential with considering of novel stiffness or inertia reduction factors for concrete sections. Present endeavor is devoted to develop new design spectra dynamic analysis of RC multistory building located in Duhok city-Iraq. Influence of proposed concrete section reduction factors on the analysis outcomes has been investigated also. Great role has been observed for introducing of stiffness reduction factors in present seismic analysis represent in magnifying of lateral deformation of building of more than 50%. Proper matching was obtained between current proposed spectrum design outputs and that for other analytical approaches.

Skew quad compensation at PEP

International Nuclear Information System (INIS)

Murray, J.J.

1977-10-01

Rotational and focal effects of solenoids used in PEP detectors will cause severe perturbations of machine beam optics and must be corrected. Ordinarily this would be accomplished by the addition of compensating solenoids and adjustment of insertion quadrupole strengths. It has been found that an arbitrary cross plane coupling representing the effects of solenoids and/or skew quads in any combination can be synthesized (or compensated) exactly using a quartet of skew quads combined with other erect transport elements in a wide variety of configurations. Specific skew quad compensating systems for PEP have been designed and are under study by PEP staff. So far no fundamental flaws have been discovered. In view of that, PEP management has tentatively authorized the use of such a system in the PEP-4, PEP-9 experiments and proposes to leave the question open ''without prejudice'' for other experiments. Use of skew quad compensation involves an imponderable risk, of course, simply because the method is new and untested. But in addition to providing the only known method for dealing with skew quad perturbations, skew quad compensation, as an alternate to compensating solenoids, promises to be much cheaper, to require much less power and to occupy much less space in the IR's. The purpose of this note is to inform potential users of the foregoing situation and to explain skew quad compensation more fully. 2 refs., 1 fig., 1 tab

Dynamic Phase Compensation of wind turbines

DEFF Research Database (Denmark)

Soerensen, P.; Skaarup, J.; Iov, Florin

2004-01-01

This paper describes a dynamic phase compensation unit for a wind turbine with directly connected induction generators. The compensation unit is based on thyristor switched capacitors, where conventional wind turbine compensations use mechanical contactors to switch the capacitors. The unit modules...

Climate change and compensation

DEFF Research Database (Denmark)

Jensen, Karsten Klint; Flanagan, Tine Bech

2013-01-01

This paper presents a case for compensation of actual harm from climate change in the poorest countries. First, it is shown that climate change threatens to reverse the fight to eradicate poverty. Secondly, it is shown how the problems raised in the literature for compensation to some extent...... are based on misconceptions and do not apply to compensation of present actual harm. Finally, two arguments are presented to the effect that, in so far as developed countries accept a major commitment to mitigate climate change, they should also accept a commitment to address or compensate actual harm from...... climate change. The first argument appeals to the principle that if it is an injustice to cause risk of incurring harm in the future, then it is also an injustice to cause a similar harm now. The second argument appeals to the principle that if there is moral reason to reduce the risk of specific harms...

33 CFR 136.217 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.217 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.217...

33 CFR 136.205 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.205 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.205...

33 CFR 136.113 - Other compensation.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT General Procedure § 136.113 Other compensation. A... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Other compensation. 136.113...

The negative differential resistance characteristics of an RC-IGBT and its equivalent circuit model

International Nuclear Information System (INIS)

Zhang Wenliang; Zhu Yangjun; Tian Xiaoli; Lu Shuojin

2014-01-01

A simple equivalent circuit model is proposed according to the device structure of reverse conducting insulated gate bipolar transistors (RC-IGBT). Mathematical derivation and circuit simulations indicate that this model can explain the snap-back effect (including primary snap-back effect, secondary snap-back effect, and reverse snap-back effect) and hysteresis effect perfectly. (semiconductor devices)

Bıldırcın ve Ördek Yumurtalarında Maya-Küf ve Total Bakteri Açısından İncelenmesi

Directory of Open Access Journals (Sweden)

Işın Var

2015-02-01

Full Text Available Bıldırcın yumurtası, besin değeri yönünden tavuk yumurtasından oransal olarak daha zengin kabul edilmektedir. Daha çok salata, pasta, mayonez vb. yapımında yaygın olarak kullanılan ördek yumurtası (Pekin ördeği tavuk yumurtasına göre daha büyük olup, ağırlıkları 70-90 g arasında değişmektedir. Bıldırcın yumurtası son yıllarda özellikle küçük çocuk ve yaşlı beslenmesinde önem kazanmıştır. Bunun yanısıra bazı hastalıkların tedavisi amacıyla da halk arasında oldukça yaygın kullanılmaktadır. Özellikle çiğ olarak tüketilen bıldırcın yumurtaları zaman zaman içerdikleri patojen mikroorganizmalarla tehlikeli olabilmektedirler. Bu çalışmada bıldırcın ve ördek yumurtalarında maya-küf ve total bakteri aranmıştır. Bıldırcın ve ördek yumurtalarının özellikle kabuğunda hem total bakteri hem de maya-küf bulunmuştur. Bıldırcın yumurtasının akı ve sarısında ise zaman zaman kontaminasyonla karşılaşılmıştır.

An Image Processing Approach to Pre-compensation for Higher-Order Aberrations in the Eye

Directory of Open Access Journals (Sweden)

Miguel Alonso Jr

2004-06-01

Full Text Available Human beings rely heavily on vision for almost all of the tasks that are required in daily life. Because of this dependence on vision, humans with visual limitations, caused by genetic inheritance, disease, or age, will have difficulty in completing many of the tasks required of them. Some individuals with severe visual impairments, known as high-order aberrations, may have difficulty in interacting with computers, even when using a traditional means of visual correction (e.g., spectacles, contact lenses. This is, in part, because these correction mechanisms can only compensate for the most regular (low-order distortions or aberrations of the image in the eye. This paper presents an image processing approach that will pre-compensate the images displayed on the computer screen, so as to counter the effect of the eye's aberrations on the image. The characterization of the eye required to perform this customized pre-compensation is the eye's Point Spread Function (PSF. Ophthalmic instruments generically called "Wavefront Analyzers" can now measure this description of the eye's optical properties. The characterization provided by these instruments also includes the "higher-order aberration components" and could, therefore, lead to a more comprehensive vision correction than traditional mechanisms. This paper explains the theoretical foundation of the methods proposed and illustrates them with experiments involving the emulation of a known and constant PSF by interposing a lens in the field of view of normally sighted test subjects.

An implementation of super-encryption using RC4A and MDTM cipher algorithms for securing PDF Files on android

Science.gov (United States)

Budiman, M. A.; Rachmawati, D.; Parlindungan, M. R.

2018-03-01

MDTM is a classical symmetric cryptographic algorithm. As with other classical algorithms, the MDTM Cipher algorithm is easy to implement but it is less secure compared to modern symmetric algorithms. In order to make it more secure, a stream cipher RC4A is added and thus the cryptosystem becomes super encryption. In this process, plaintexts derived from PDFs are firstly encrypted with the MDTM Cipher algorithm and are encrypted once more with the RC4A algorithm. The test results show that the value of complexity is Θ(n2) and the running time is linearly directly proportional to the length of plaintext characters and the keys entered.

Information spreading dynamics in hypernetworks

Science.gov (United States)

Suo, Qi; Guo, Jin-Li; Shen, Ai-Zhong

2018-04-01

Contact pattern and spreading strategy fundamentally influence the spread of information. Current mathematical methods largely assume that contacts between individuals are fixed by networks. In fact, individuals are affected by all his/her neighbors in different social relationships. Here, we develop a mathematical approach to depict the information spreading process in hypernetworks. Each individual is viewed as a node, and each social relationship containing the individual is viewed as a hyperedge. Based on SIS epidemic model, we construct two spreading models. One model is based on global transmission, corresponding to RP strategy. The other is based on local transmission, corresponding to CP strategy. These models can degenerate into complex network models with a special parameter. Thus hypernetwork models extend the traditional models and are more realistic. Further, we discuss the impact of parameters including structure parameters of hypernetwork, spreading rate, recovering rate as well as information seed on the models. Propagation time and density of informed nodes can reveal the overall trend of information dissemination. Comparing these two models, we find out that there is no spreading threshold in RP, while there exists a spreading threshold in CP. The RP strategy induces a broader and faster information spreading process under the same parameters.

20 CFR 211.2 - Definition of compensation.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Definition of compensation. 211.2 Section 211.2 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD RETIREMENT ACT CREDITABLE RAILROAD COMPENSATION § 211.2 Definition of compensation. (a) The term compensation means any form...

Effect of web openings on the structural behavior of RC beams subjected to pure torsion

Directory of Open Access Journals (Sweden)

Abdo Taha

2017-01-01

Full Text Available In the construction of modern buildings, the presence of openings became a necessity nowadays in order to accommodate the many pipes and ducts required for the different services. On the other hand, the presence of these openings in RC beams affects their structural behavior. One important behavior that needs further study would be torsion. Currently, there are no guide lines available to analyze or design RC beams with web openings under pure torsion. Thus, the main objective of this research is to investigate the behavior of simply supported RC beams with openings subjected to pure torsion. In the first part of this paper, an experimental study is conducted on seven beams subjected to pure torsion loading in order to investigate the effect of the number of openings, the spacing between stirrups, and beam depth. All beams have a constant clear span length of 1800 mm and a constant beam width of 150 mm. The beams have varying opening number and stirrups arrangement as well as varying beam depth in order to investigate the effect of these parameters on the behavior of the beams. Systematic measurements such as the cracking torque, the ultimate torque, the angle of rotation of the beam at cracking, and the angle of rotation of the beam at the ultimate load are conducted for further understanding of the beam behavior under torsion. In the second part of the paper, the experimental results are compared with the numerical results obtained using the non-linear finite element analysis program, ANSYS. Good agreement between the experimental and numerical results is found.

Center for Worker's Compensation Studies

Data.gov (United States)

Federal Laboratory Consortium — The mission of the NIOSH Center for Workers’ Compensation Studies (CWCS) is to use workers’ compensation data and systems to improve workplace safety and health....

Risk Quantification for Sustaining Coastal Military Installation Asset and Mission Capabilities (RC-1701)

Science.gov (United States)

2014-06-06

5a. CONTRACT NUMBER Risk Quantification for Sustaining Coastal Military Installation Asset and Mission Capabilities (RC-1701) 5b. GRANT NUMBER...Planetary Boundary Layer (PBL) wind model TC96 (Thompson and Cardone 1996), 2) Surge has been simulated using the ADvanced CIRCulation model ADCIRC...coefficient, and h is the depth of the PBL (Thompson and Cardone 1996). The cyclone pressure is defined by an axisymmetrical exponential pressure or by

Probable Chemical Hypoxia Effects on Progress of CNV Through Induction of Promoter CpG Demethylation and Overexpression of IL17RC in Human RPE Cells.

Science.gov (United States)

Alivand, Mohammad Reza; Sabouni, Farzaneh; Soheili, Zahra-Soheila

2016-09-01

To survey the changes of promoter CpG methylation status and mRNA expression of IL17RC (interleukin 17 receptor C) gene in retinal pigment epithelium (RPE) cells under chemical hypoxia condition for choroidal neovascularization (CNV) modeling in vitro. RPE cells were cultured in both untreated as a control group and treated by cobalt chloride media as a hypoxia group for various concentrations (100-150μM) and times (24-36 hrs.) To confirm chemical hypoxia condition, mRNA expression of HIF (Hypoxia Inducible Factor) -1α, -2α, and Vascular Endothelial Growth Factor (VEGF) was compared between two groups by Real-time PCR. Also, in normoxia and hypoxia conditions, IL17RC expression changes and promoter CpG methylation status were evaluated by Real-time PCR and methylation-specific PCR (MSP) techniques, respectively. Overexpression of HIF-1α, HIF-2α, and VEGF was significant in hypoxia versus normoxia conditions. Our data showed overexpression of IL17RC (2.1- to 6.3-fold) and decreasing of its promoter methylation in comparison with hypoxia and normoxia conditions. It was found that there are significant association between promoter methylation status and expression of IL17RC in chemical hypoxia condition. Therefore, methylation of IL17RC could play as a marker in CNV and degeneration of RPE cells in vitro. Additionally, HIF-α and methylation phenomena may be considered as critical targets for blocking in angiogenesis of age-related degeneration in future studies.

28 CFR 104.21 - Filing for compensation.

Science.gov (United States)

2010-07-01

... “Personal Injury Compensation Form” or a “Death Compensation Form.” A claim shall be deemed “filed” for... filing either a “Personal Injury Compensation Form” or a “Death Compensation Form,” the claim shall be..., when a Claims Evaluator determines that both the Eligibility Form and either a Personal Injury...

Aeromagnetic Compensation for UAVs

Science.gov (United States)

Naprstek, T.; Lee, M. D.

2017-12-01

Aeromagnetic data is one of the most widely collected types of data in exploration geophysics. With the continuing prevalence of unmanned air vehicles (UAVs) in everyday life there is a strong push for aeromagnetic data collection using UAVs. However, apart from the many political and legal barriers to overcome in the development of UAVs as aeromagnetic data collection platforms, there are also significant scientific hurdles, primary of which is magnetic compensation. This is a well-established process in manned aircraft achieved through a combination of platform magnetic de-noising and compensation routines. However, not all of this protocol can be directly applied to UAVs due to fundamental differences in the platforms, most notably the decrease in scale causing magnetometers to be significantly closer to the avionics. As such, the methodology must be suitably adjusted. The National Research Council of Canada has collaborated with Aeromagnetic Solutions Incorporated to develop a standardized approach to de-noising and compensating UAVs, which is accomplished through a series of static and dynamic experiments. On the ground, small static tests are conducted on individual components to determine their magnetization. If they are highly magnetic, they are removed, demagnetized, or characterized such that they can be accounted for in the compensation. Dynamic tests can include measuring specific components as they are powered on and off to assess their potential effect on airborne data. The UAV is then flown, and a modified compensation routine is applied. These modifications include utilizing onboard autopilot current sensors as additional terms in the compensation algorithm. This process has been applied with success to fixed-wing and rotary-wing platforms, with both a standard manned-aircraft magnetometer, as well as a new atomic magnetometer, much smaller in scale.

Reverse preferential spread in complex networks

Science.gov (United States)

Toyoizumi, Hiroshi; Tani, Seiichi; Miyoshi, Naoto; Okamoto, Yoshio

2012-08-01

Large-degree nodes may have a larger influence on the network, but they can be bottlenecks for spreading information since spreading attempts tend to concentrate on these nodes and become redundant. We discuss that the reverse preferential spread (distributing information inversely proportional to the degree of the receiving node) has an advantage over other spread mechanisms. In large uncorrelated networks, we show that the mean number of nodes that receive information under the reverse preferential spread is an upper bound among any other weight-based spread mechanisms, and this upper bound is indeed a logistic growth independent of the degree distribution.

Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

Energy Technology Data Exchange (ETDEWEB)

Le Coroller, Y. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-09-01

A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux

Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

Energy Technology Data Exchange (ETDEWEB)

Le Coroller, Y [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-09-01

A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux millimetres fonctionnent

Structuring competitive physician compensation models.

Science.gov (United States)

Mobley, Kim; Turcotte, Claire

2010-12-01

When developing and reviewing their physician compensation programs, healthcare organizations should: Understand the market data. Test outcomes of incentive plans for fair market value. Check total compensation for fair market value and reasonableness.

Does CEO compensation impact patient satisfaction?

Science.gov (United States)

Akingbola, Kunle; van den Berg, Herman A

2015-01-01

This study examines the relationship between CEO compensation and patient satisfaction in Ontario, Canada. The purpose of this paper is to determine what impact hospital CEO compensation has on hospital patient satisfaction. The analyses in this study were based on data of 261 CEO-hospital-year observations in a sample of 103 nonprofit hospitals. A number of linear regressions were conducted, with patient satisfaction as the dependent variable and CEO compensation as the independent variable of interest. Controlling variables included hospital size, type of hospital, and frequency of adverse clinical outcomes. CEO compensation does not significantly influence hospital patient satisfaction. Both patient satisfaction and CEO compensation appear to be driven primarily by hospital size. Patient satisfaction decreases, while CEO compensation increases, with the number of acute care beds in a hospital. In addition, CEO compensation does not even appear to moderate the influence of hospital size on patient satisfaction. There are several limitations to this study. First, observations of CEO-hospital-years in which annual nominal CEO compensation was below $100,000 were excluded, as they were not publicly available. Second, this research was limited to a three-year range. Third, this study related the compensation of individual CEOs to a measure of performance based on a multitude of patient satisfaction surveys. Finally, this research is restricted to not-for-profit hospitals in Ontario, Canada. The findings seem to suggest that hospital directors seeking to improve patient satisfaction may find their efforts frustrated if they focus exclusively on the hospital CEO. The findings highlight the need for further research on how CEOs may, through leading and supporting those hospital clinicians and staff that interact more closely with patients, indirectly enhance patient satisfaction. To the best of the authors' knowledge, no research has examined the relationship between

How Is Mono Spread?

Science.gov (United States)

... How Is Mono Spread? Print My sister has mononucleosis. I drank out of her drink before we ... that I have mono now? – Kyle* Mono, or mononucleosis, is spread through direct contact with saliva. This ...

Effect of the Fiber Type and Axial Stiffness of FRCM on the Flexural Strengthening of RC Beams

Directory of Open Access Journals (Sweden)

Abdulla Jabr

2017-01-01

Full Text Available The use of externally-bonded fiber-reinforced polymer (FRP sheets has been successfully used in the repair and strengthening of both the shear and flexural capacities of reinforced concrete (RC beams, slabs and columns since the 1990s. However, the externally-bonded FRP reinforcements still present many disadvantages, such as poor performance in elevated temperature and fire, lack of permeability and strength degradation when exposed to ultraviolet radiation. To remedy such drawbacks, the fiber-/fabric-reinforced cementitious matrix (FRCM has been recently introduced. The FRCM system consists of a fiber mesh or grid embedded in a cementitious bonding material. The present research investigates the flexural strengthening of reinforced concrete (RC beams with FRCM. The experimental testing included eight large-scale concrete beams, 150 mm × 250 mm × 2400 mm, internally reinforced with steel bars and strengthened in flexure with FRCM. The investigated parameters were the internal steel reinforcement ratio and the FRCM systems. Two steel reinforcement ratios of 0.18 and 0.36 of the balanced reinforcement ratio, as well as three FRCM systems using glass, carbon and PBO fibers were investigated. Test results are presented in terms of load-deflection, load-strain and load-crack width relationships. The test results indicated that the PBO FRCM significantly increased the ultimate capacity of the strengthened RC beams with both low and moderate internal reinforcement ratios compared to the glass and carbon FRCM.

A new 4π(LS)-γ coincidence counter at NCBJ RC POLATOM with TDCR detector in the beta channel.

Science.gov (United States)

Ziemek, T; Jęczmieniowski, A; Cacko, D; Broda, R; Lech, E

2016-03-01

A new 4π(LS)-γ coincidence system (TDCRG) was built at the NCBJ RC POLATOM. The counter consists of a TDCR detector in the beta channel and scintillation detector with NaI(Tl) crystal in the gamma channel. The system is equipped with a digital board with FPGA, which records and analyses coincidences in the TDCR detector and coincidences between the beta and gamma channels. The characteristics of the system and a scheme of the FPGA implementation with behavioral simulation are given. The TDCRG counter was validated by activity measurements on (14)C and (60)Co solutions standardized in RC POLATOM using previously validated methods. Copyright © 2015 Elsevier Ltd. All rights reserved.

Compensation for oil pollution damage caused by oil spills from ships and the International Oil Pollution Compensation Fund

International Nuclear Information System (INIS)

Jacobsson, M.

1994-01-01

Liability and compensation for pollution damage caused by oil spills from laden tankers is governed by two international conventions: the 1969 Civil Liability Convention and the 1971 Fund Convention. The Civil Liability Convention established a system of strict liability for tanker owners and introduced compulsory liability insurance. The Fund Convention created a system of supplementary compensation administered by an intergovernmental organization, the International Oil Pollution Compensation Fund (IOPC Fund), which at present has 56 member states (August 1993). The IOPC Fund pays compensation to victims of oil pollution in member states when the compensation from the ship owner and his insurer is insufficient. (author)

Vertical vibration analysis for elevator compensating sheave

Science.gov (United States)

Watanabe, Seiji; Okawa, Takeya; Nakazawa, Daisuke; Fukui, Daiki

2013-07-01

Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified.

Vertical vibration analysis for elevator compensating sheave

International Nuclear Information System (INIS)

Watanabe, Seiji; Nakazawa, Daisuke; Fukui, Daiki; Okawa, Takeya

2013-01-01

Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified

Simplified unified analysis of switched-RC passive mixers, samplers, and N -Path filters using the adjoint network

NARCIS (Netherlands)

Pavan, Shanthi; Klumperink, Eric A.M.

2017-01-01

Recent innovations in software defined CMOS radio transceiver architectures heavily rely on high linearity switched-RC sampler and passive-mixer circuits, driven by digitally programmable multiphase clocks. Although seemingly simple, the frequency domain analysis of these linear periodically time

23 CFR 751.15 - Just compensation.

Science.gov (United States)

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Just compensation. 751.15 Section 751.15 Highways... AND ACQUISITION § 751.15 Just compensation. (a) Just compensation shall be paid the owner for the... nonconforming junkyard as provided in § 751.11 must pertain at the time of the taking or removal in order to...

Radiotherapy dose compensation for lung patients

International Nuclear Information System (INIS)

Piyaratna, N.; Arnold, A.; Metcalfe, P.

1999-01-01

The purpose of the present paper is to provide a more homogeneous dose distribution in the target volume from compensated anterior and posterior fields while the healthy lung is spared by de-weighting the lateral fields. A compensation computation which used linear iterations to compute the most homogeneous dose distribution across the target volume was applied to produce optimum compensator designs. The equivalent tissue-air ratio (E-TAR) inhomogeneity correction was applied for the computations using a GE target series 11 planning computer. The compensators designed were tested for accuracy in a modified water/lung phantom using a scanning diode and an anthropomorphic phantom using thermoluminescent dosimeters. A comparison has been made between the compensated and uncompensated plans for the first nine patients who we have treated with this technique. The dose profiles produced by the computation agreed with the prediction of the computed isodose plans to within ± 2% at the target depth. The thermoluminescent dosimeter (TLD)-measured results in the anthropomorphic phantom agreed with the planning computer within ± 3%. A comparison of nine compensated plans of radiotherapy patients for large-volume targets in the lung region showed a maximum variation in the target to be 19% uncompensated versus 10% compensated. By providing compensated treatment fields from anterior and posterior treatment portals, a homogeneous dose that conforms well to the target volume is provided. As an added bonus, this enables the lateral lung fields to be significantly de-weighted and the healthy lung is spared considerable dose. Copyright (1999) Blackwell Science Pty Ltd

Interaction between corrosion crack width and steel loss in RC beams corroded under load

International Nuclear Information System (INIS)

Malumbela, Goitseone; Alexander, Mark; Moyo, Pilate

2010-01-01

This paper presents results and discussions on an experimental study conducted to relate the rate of widening of corrosion cracks with the pattern of corrosion cracks as well as the level of steel corrosion for RC beams (153 x 254 x 3000 mm) that were corroded whilst subjected to varying levels of sustained loads. Steel corrosion was limited to the tensile reinforcement and to a length of 700 mm at the centre of the beams. The rate of widening of corrosion cracks as well as strains on uncracked faces of RC beams was constantly monitored during the corrosion process, along the corrosion region and along other potential cracking faces of beams using a demec gauge. The distribution of the gravimetric mass loss of steel along the corrosion region was measured at the end of the corrosion process. The results obtained showed that: the rate of widening of each corrosion crack is dependent on the overall pattern of the cracks whilst the rate of corrosion is independent of the pattern of corrosion cracks. A mass loss of steel of 1% was found to induce a corrosion crack width of about 0.04 mm.

Effect of URM infills on seismic vulnerability of Indian code designed RC frame buildings

Science.gov (United States)

Haldar, Putul; Singh, Yogendra; Paul, D. K.

2012-03-01

Unreinforced Masonry (URM) is the most common partitioning material in framed buildings in India and many other countries. Although it is well-known that under lateral loading the behavior and modes of failure of the frame buildings change significantly due to infill-frame interaction, the general design practice is to treat infills as nonstructural elements and their stiffness, strength and interaction with the frame is often ignored, primarily because of difficulties in simulation and lack of modeling guidelines in design codes. The Indian Standard, like many other national codes, does not provide explicit insight into the anticipated performance and associated vulnerability of infilled frames. This paper presents an analytical study on the seismic performance and fragility analysis of Indian code-designed RC frame buildings with and without URM infills. Infills are modeled as diagonal struts as per ASCE 41 guidelines and various modes of failure are considered. HAZUS methodology along with nonlinear static analysis is used to compare the seismic vulnerability of bare and infilled frames. The comparative study suggests that URM infills result in a significant increase in the seismic vulnerability of RC frames and their effect needs to be properly incorporated in design codes.

Experimental investigations into the shear behavior of self-compacting RC beams with and without shear reinforcement

Directory of Open Access Journals (Sweden)

Ammar N. HANOON

2014-12-01

Full Text Available Self-compacting concrete (SCC is a new generation of high-performance concrete, known for its excellent deformability and high resistance to segregation and bleeding. Nonetheless, SCC may be incapable of resisting shear because the shear resistance mechanisms of this concrete are uncertain, especially the aggregate interlock mechanism. This uncertainty is attributed to the fact that SCC contains a smaller amount of coarse aggregates than normal concrete (NC does. This study focuses on the shear strength of self-compacting reinforced concrete (RC beams with and without shear reinforcement. A total of 16 RC beam specimens was manufactured and tested in terms of shear span-to-depth ratio and flexural and shear reinforcement ratio. The test results were compared with those of the shear design equations developed by ACI, BS, CAN and NZ codes. Results show that an increase in web reinforcement enhanced cracking strength and ultimate load. Shear-tension failure was the control failure in all tested beams.

Enthalpy-entropy compensation in protein unfolding

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

Enthalpy-entropy compensation was found to be a universal law in protein unfolding based on over 3 000 experimental data. Water molecular reorganization accompanying the protein unfolding was suggested as the origin of the enthalpy-entropy compensation in protein unfolding. It is indicated that the enthalpy-entropy compensation constitutes the physical foundation that satisfies the biological need of the small free energy changes in protein unfolding, without the sacrifice of the bio-diversity of proteins. The enthalpy-entropy compensation theory proposed herein also provides valuable insights into the Privalov's puzzle of enthalpy and entropy convergence in protein unfolding.

Modal Identification of a Time-Invariant 6-Storey Model Test RC-Frame from Free Decay Tests using Multi-Variate Models

DEFF Research Database (Denmark)

Skjærbæk, P. S.; Nielsen, Søren R. K.; Kirkegaard, Poul Henning

1997-01-01

in the comparison. The data investigated are sampled from a laboratory model of a plane 6-storey, 2-bay RC-frame. The laboratory model is excited at the top storey where two different types of excitation where considered. In the first case the structure was excited in the first mode and in the second case......The scope of the paper is to apply multi-variate time-domain models for identification of eginfrequencies and mode shapes of a time- invariant model test Reinforced Concrete (RC) frame from measured decays. The frequencies and mode shapes of interest are the two lowest ones since they are normally...

Modal Identification of a Time-Invariant 6-Storey Model Test RC-Frame from Free Decay Tests using Multi-Variate Models

DEFF Research Database (Denmark)

Skjærbæk, P. S.; Nielsen, Søren R. K.; Kirkegaard, Poul Henning

in the comparison. The data investigated are sampled from a laboratory model of a plane 6-storey, 2-bay RC-frame. The laboratory model is excited at the top storey where two different types of excitation where considered. In the first case the structure was excited in the first mode and in the second case......The scope of the paper is to apply multi-variate time-domain models for identification of eginfrequencies and mode shapes of a time- invariant model test Reinforced Concrete (RC) frame from measured decays. The frequencies and mode shapes of interest are the two lowest ones since they are normally...

Shear Resistance Capacity of Interface of Plate-Studs Connection between CFST Column and RC Beam

Directory of Open Access Journals (Sweden)

Qianqian Wang

2017-01-01

Full Text Available The combination of a concrete-filled steel tube (CFST column and reinforced concrete (RC beam produces a composite structural system that affords good structural performance, functionality, and workability. The effective transmission of moments and shear forces from the beam to the column is key to the full exploitation of the structural performance. The studs of the composite beam transfer the interfacial shear force between the steel beam and the concrete slab, with the web bearing most of the vertical shear force of the steel beam. In this study, the studs and vertical steel plate were welded to facilitate the transfer of the interfacial shear force between the RC beam and CFST column. Six groups of a total of 18 specimens were used to investigate the shear transfer mechanism and failure mode of the plate-studs connection, which was confirmed to effectively transmit the shear forces between the beam and column. The results of theoretical calculations were also observed to be in good agreement with the experimental measurements.

Theoretical Study of Watershed Eco-Compensation Standards

Science.gov (United States)

Yan, Dandan; Fu, Yicheng; Liu, Biu; Sha, Jinxia

2018-01-01

Watershed eco-compensation is an effective way to solve conflicts over water allocation and ecological destruction problems in the exploitation of water resources. Despite an increasing interest in the topic, the researches has neglected the effect of water quality and lacked systematic calculation method. In this study we reviewed and analyzed the current literature and proposedatheoretical framework to improve the calculation of co-compensation standard.Considering the perspectives of the river ecosystems, forest ecosystems and wetland ecosystems, the benefit compensation standard was determined by the input-output corresponding relationship. Based on the opportunity costs related to limiting development and water conservation loss, the eco-compensation standard was calculated.In order to eliminate the defects of eco-compensation implementation, the improvement suggestions were proposed for the compensation standard calculation and implementation.

Hybrid spread spectrum radio system

Science.gov (United States)

Smith, Stephen F [London, TN; Dress, William B [Camas, WA

2010-02-09

Systems and methods are described for hybrid spread spectrum radio systems. A method, includes receiving a hybrid spread spectrum signal including: fast frequency hopping demodulating and direct sequence demodulating a direct sequence spread spectrum signal, wherein multiple frequency hops occur within a single data-bit time and each bit is represented by chip transmissions at multiple frequencies.

Susceptibility of the MMPI-2 Clinical, Restructured Clinical (RC), and Content Scales to Overreporting and Underreporting

Science.gov (United States)

Sellbom, Martin; Ben-Porath, Yossef S.; Graham, John R.; Arbisi, Paul A.; Bagby, R. Michael

2005-01-01

The authors examined and compared the susceptibility of three Minnesota Multiphasic Personality Inventory-2 (MMPI-2) scale sets (Clinical, Restructured Clinical [RC], and Content) to over- and underreporting using five analog samples. Two samples of 85 and 191 undergraduate students, respectively, took the MMPI-2 under underreporting versus…

Addressing inadequate compensation | IDRC - International ...

International Development Research Centre (IDRC) Digital Library (Canada)

2016-08-12

Aug 12, 2016 ... The issue LSLAs raise a number of concerns regarding compensation, including ... at a meeting with traders in Lamu, Kenya, where a new port is planned. ... compensation and a fair share of benefits and risks in land deals.

Sociální vztahy a postoje v ženském ragbyovém týmu RC Tatra Smíchov

OpenAIRE

Kadavá, Tereza

2014-01-01

Title: Social Relationships and Attitudes in Women's RC Tatra Smichov Rugby Team Objectives: The main objective of this thesis is to analyze social relations and attitudes in the women's RC Tatra Smichov rugby team and to create the profiles of the players. The analysis should help the new coach to get to know the players well, focusing mainly on their career, ambition, motivation, and feelings during trainings and matches. At the same time, it should shed light on how they perceive themselve...

Is there a clinical benefit with a smooth compensator design compared with a plunged compensator design for passive scattered protons?

Energy Technology Data Exchange (ETDEWEB)

Tabibian, Art A., E-mail: art.tabibian@gmail.com [University of Texas School of Allied Health-Medical Dosimetry, Houston, TX (United States); Powers, Adam; Dolormente, Keith; Oommen, Sneha; Tiwari, Akhil [University of Texas School of Allied Health-Medical Dosimetry, Houston, TX (United States); Palmer, Matt [MD Anderson Department of Radiation Oncology, Houston, TX (United States); Zhu, Xiaorong R.; Li, Heng; Sahoo, Narayan; Wisdom, Paul [MD Anderson Department of Radiation Physics, Houston, TX (United States); Velasco, Kyle [Radiation Oncology Resources, Goshen, IN (United States); Erhart, Kevin; Stanley, Henry [Decimal, Inc, Sanford, FL (United States); Nguyen, Bao-Ngoc T. [MD Anderson Department of Radiation Oncology, Houston, TX (United States)

2015-04-01

In proton therapy, passive scattered proton plans use compensators to conform the dose to the distal surface of the planning volume. These devices are custom made from acrylic or wax for each treatment field using either a plunge-drilled or smooth-milled compensator design. The purpose of this study was to investigate if there is a clinical benefit of generating passive scattered proton radiation treatment plans with the smooth compensator design. We generated 4 plans with different techniques using the smooth compensators. We chose 5 sites and 5 patients for each site for the range of dosimetric effects to show adequate sample. The plans were compared and evaluated using multicriteria (MCA) plan quality metrics for plan assessment and comparison using the Quality Reports [EMR] technology by Canis Lupus LLC. The average absolute difference for dosimetric metrics from the plunged-depth plan ranged from −4.7 to +3.0 and the average absolute performance results ranged from −6.6% to +3%. The manually edited smooth compensator plan yielded the best dosimetric metric, +3.0, and performance, + 3.0% compared to the plunged-depth plan. It was also superior to the other smooth compensator plans. Our results indicate that there are multiple approaches to achieve plans with smooth compensators similar to the plunged-depth plans. The smooth compensators with manual compensator edits yielded equal or better target coverage and normal tissue (NT) doses compared with the other smooth compensator techniques. Further studies are under investigation to evaluate the robustness of the smooth compensator design.

What Constitutes Fair Compensation for Unfair Dismissal

African Journals Online (AJOL)

user

Generally the monetary compensation is perceived to be a solatium. 19 .... compensation for non-patrimonial loss in the context of an unfair labour practice. 41 .... awards of compensation where a person's dignity is impaired in the course of an.

Compensative hypertrophy of the kidney

International Nuclear Information System (INIS)

Raynaud, C.

1976-01-01

Several measurement methods are available to practitioners to reveal a compensative hypertrophy. Mensuration of the kidney has the advantage of simplicity but is in fact an unreliable and inaccurate method. Separate clearances in their traditional form have never entered into routine use because of the disadvantages of ureteral catheterism. The use of radioactive tracers avoids this drawback, but clearances calculated in this way are only valid in the absence of obstructive urinary disorders. Solutions have been proposed, but the values obtained are no longer identical with the clearances. The Hg uptake test quantifies quite accurately the function of each kidney. From the results obtained a complete compensative hypertrophy developed on a healthy kidney and an incomplete compensative hypertrophy developed on the diseased kidney have been described. In each of these situations the degree to which compensative hypertrophy develops seems to be fixed at a given level peculiar to each patient [fr

Defining Compensable Injury in Biomedical Research.

Science.gov (United States)

Larkin, Megan E

2015-01-01

Biomedical research provides a core social good by enabling medical progress. In the twenty-first century alone, this includes reducing transmission of HIV/AIDS, developing innovative therapies for cancer patients, and exploring the possibilities of personalized medicine. In order to continue to advance medical science, research relies on the voluntary participation of human subjects. Because research is inherently uncertain, unintended harm is an inevitable part of the research enterprise. Currently, injured research participants in the United States must turn to the “litigation lottery” of the tort system in search of compensation. This state of affairs fails research participants, who are too often left uncompensated for devastating losses, and makes the United States an outlier in the international community. In spite of forty years’ worth of Presidential Commissions and other respected voices calling for the development of a no-fault compensation system, no progress has been made to date. One of the reasons for this lack of progress is the failure to develop a coherent ethical basis for an obligation to provide compensation for research related injuries. This problem is exacerbated by the lack of a clear definition of “compensable injury” in the biomedical research context. This article makes a number of important contributions to the scholarship in this growing field. To begin, it examines compensation systems already in existence and concludes that there are four main definitional elements that must be used to define “compensable injury.” Next, it examines the justifications that have been put forth as the basis for an ethical obligation to provide compensation, and settles on retrospective nonmaleficence and distributive and compensatory justice as the most salient and persuasive. Finally, it uses the regulatory elements and the justifications discussed in the first two sections to develop a well-rounded definition of “compensable injury�

Delayed release formulation of the somatostatin analog RC-160 inhibits the growth hormone (GH) response to GH-releasing factor-(1-29)NH2 and decreases elevated prolactin levels in rats.

Science.gov (United States)

Bokser, L; Schally, A V

1988-10-01

Recently, we have developed a long-acting delivery system for our somatostatin (SS) analog RC-160 based on injectable microcapsules in poly-(D,L-lactide-coglycolide). We studied the capacity of this formulation to repeatedly block the GH secretion induced by administration of GRF-(1-29)NH2 (GRF) on different days. Male rats anesthetized with pentobarbital were injected iv with 2.5 micrograms/kg BW GRF-(1-29)NH2 or saline. Five minutes later, blood samples were taken for GH measurement, and the animals were injected im with RC-160 microcapsules at a dose calculated to release 25 micrograms/day of the analog for 7 days or with the vehicle. The GRF stimuli were repeated 48 h, 96 h, and 8 days after administration of SS analog in microcapsules. GRF administration increased GH levels at the four times tested (P less than 0.01) in the control group injected with vehicle, while RC-160 microcapsules inhibited the GH response for more than 96 h (P less than 0.01). The GH levels augmented by pentobarbital were also decreased by the RC-160 microcapsules (P less than 0.01). Animals treated with microcapsules showed smaller increases in their body weight than untreated rats (P less than 0.05). We also investigated the effect of RC-160 microcapsules on hyperprolactinemic female rats implanted with pituitary glands under the kidney capsules. High PRL levels in rats bearing pituitary grafts showed a significant decrease when measured 4 days after the administration of RC-160 microcapsules. These results demonstrate the efficacy of the long-acting delivery system of the SS analog RC-160 and suggest the possible clinical usefulness of this formulation for lowering GH and PRL levels.

38 CFR 3.5 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation General § 3.5 Dependency and indemnity compensation. (a) Dependency and indemnity compensation. This term means a monthly payment made by...

Global patterns and trends in human-wildlife conflict compensation.

Science.gov (United States)

Ravenelle, Jeremy; Nyhus, Philip J

2017-12-01

Human-wildlife conflict is a major conservation challenge, and compensation for wildlife damage is a widely used economic tool to mitigate this conflict. The effectiveness of this management tool is widely debated. The relative importance of factors associated with compensation success is unclear, and little is known about global geographic or taxonomic differences in the application of compensation programs. We reviewed research on wildlife-damage compensation to determine geographic and taxonomic gaps, analyze patterns of positive and negative comments related to compensation, and assess the relative magnitude of global compensation payments. We analyzed 288 publications referencing wildlife compensation and identified 138 unique compensation programs. These publications reported US$222 million (adjusted for inflation) spent on compensation in 50 countries since 1980. Europeans published the most articles, and compensation funding was highest in Europe, where depredation by wolves and bears was the most frequently compensated damage. Authors of the publications we reviewed made twice as many negative comments as positive comments about compensation. Three-quarters of the negative comments related to program administration. Conversely, three-quarters of the positive comments related to program outcomes. The 3 most common suggestions to improve compensation programs included requiring claimants to employ damage-prevention practices, such as improving livestock husbandry or fencing of crops to receive compensation (n = 25, 15%); modifying ex post compensation schemes to some form of outcome-based performance payment (n = 21, 12%); and altering programs to make compensation payments more quickly (n = 14, 8%). We suggest that further understanding of the strengths and weaknesses of compensation as a conflict-mitigation tool will require more systematic evaluation of the factors driving these opinions and that differentiating process and outcomes and understanding

Evaluation equivalent pulse of pulse-like ground motion to estimate the response of RC moment-resisting frames

Directory of Open Access Journals (Sweden)

Seyed Rohollah Hosseini Vaez

2017-08-01

Full Text Available In this study the ability of equivalent pulse extracted by a mathematical model from pulse-like ground motion is investigated in order to estimate the response of RC moment-resisting frames. By examining the mathematical model, it is obvious that the model-based elastic response spectra are compatible with the actual pulse-like record. Also, the model simulates the long-period portion of actual pulse-like records by a high level of precision. The results indicate that the model adequately simulates the components of time histories. In order to investigate the ability of equivalent pulse of pulse-like ground motion in estimating the response of RC moment-resisting frames, five frame models including 3, 6, 9, 12 and 15 stories analyzed under actual record and simulated one. The results of the base shear demand, the maximum value of the inter-story drift and the distribution of inter-story drift along the height of the structures in three levels of design ductility is investigated. According to the results of this study, the equivalent pulses can predict accurately the response of regular RC moment-resisting frames when the fundamental period of the structure is equal to or greater than the equivalent pulse of the record. For the ground motion with high-frequency content the difference is high; but with increasing the number of stories and approaching pulse period to the fundamental period of the structure and increasing the level of design ductility of structure, more accurately predict the structural response.

Compensation of PVT Variations in ToF Imagers with In-Pixel TDC.

Science.gov (United States)

Vornicu, Ion; Carmona-Galán, Ricardo; Rodríguez-Vázquez, Ángel

2017-05-09

The design of a direct time-of-flight complementary metal-oxide-semiconductor (CMOS) image sensor (dToF-CIS) based on a single-photon avalanche-diode (SPAD) array with an in-pixel time-to-digital converter (TDC) must contemplate system-level aspects that affect its overall performance. This paper provides a detailed analysis of the impact of process parameters, voltage supply, and temperature (PVT) variations on the time bin of the TDC array. Moreover, the design and characterization of a global compensation loop is presented. It is based on a phase locked loop (PLL) that is integrated on-chip. The main building block of the PLL is a voltage-controlled ring-oscillator (VCRO) that is identical to the ones employed for the in-pixel TDCs. The reference voltage that drives the master VCRO is distributed to the voltage control inputs of the slave VCROs such that their multiphase outputs become invariant to PVT changes. These outputs act as time interpolators for the TDCs. Therefore the compensation scheme prevents the time bin of the TDCs from drifting over time due to the aforementioned factors. Moreover, the same scheme is used to program different time resolutions of the direct time-of-flight (ToF) imager aimed at 3D ranging or depth map imaging. Experimental results that validate the analysis are provided as well. The compensation loop proves to be remarkably effective. The spreading of the TDCs time bin is lowered from: (i) 20% down to 2.4% while the temperature ranges from 0 °C to 100 °C; (ii) 27% down to 0.27%, when the voltage supply changes within ±10% of the nominal value; (iii) 5.2 ps to 2 ps standard deviation over 30 sample chips, due to process parameters' variation.

Compensating customer-generators: a taxonomy describing methods of compensating customer-generators for electricity supplied to the grid

International Nuclear Information System (INIS)

Hughes, Larry; Bell, Jeff

2006-01-01

The increasing popularity of on-site power generation is driving the demand for methods to compensate customer-generators that supply electricity to the grid. Although many practices exist for providing such compensation, confusion surrounds the terms often used to describe such practices (notably, net metering and net billing). To help clarify this situation, the following paper proposes a taxonomy that distinguishes between 16 distinct compensation practices

Default Spread dan Term Spread sebagai Variabel Proxy Siklus Bisnis pada Model Fama-French

Directory of Open Access Journals (Sweden)

Edwin Hendra

2015-08-01

Full Text Available This research aims to apply the Fama-French models and test the effect of alternative variable of bond yield spread, default spread (RBBB – RAAA and RAAA – RF, and the term spread (RSUN10-RSUN1, as proxy variables of the business cycle, in IDX stock data during 2005-2010. Four types of asset pricing models tested are Sharpe-Lintner CAPM, Fama-French models, Hwang et al.model, and hybrid model. The results showed that the size effect and value effect has an impact on excess stock returns. Slopes of market beta, SMB, and HML are more sensitive to stock big size and high B / M. Default spreads and term spreads in Hwang et al. model can explain the value effect, and weakly explain the size effect, meanwhile the power of explanation disappeared on Hybrid models. Based on the assessment adjusted R2 and the frequency of rejection of non-zero alpha, is found that the hybrid model is the most suitable model.  

Takeovers and (Excess) CEO Compensation

NARCIS (Netherlands)

Feito Ruiz, Isabel; Renneboog, Luc

2017-01-01

We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

Takeovers and (excess) CEO compensation

NARCIS (Netherlands)

Feito Ruiz, Isabel; Renneboog, Luc

We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

Optimal compensation for neuron loss

Science.gov (United States)

Barrett, David GT; Denève, Sophie; Machens, Christian K

2016-01-01

The brain has an impressive ability to withstand neural damage. Diseases that kill neurons can go unnoticed for years, and incomplete brain lesions or silencing of neurons often fail to produce any behavioral effect. How does the brain compensate for such damage, and what are the limits of this compensation? We propose that neural circuits instantly compensate for neuron loss, thereby preserving their function as much as possible. We show that this compensation can explain changes in tuning curves induced by neuron silencing across a variety of systems, including the primary visual cortex. We find that compensatory mechanisms can be implemented through the dynamics of networks with a tight balance of excitation and inhibition, without requiring synaptic plasticity. The limits of this compensatory mechanism are reached when excitation and inhibition become unbalanced, thereby demarcating a recovery boundary, where signal representation fails and where diseases may become symptomatic. DOI: http://dx.doi.org/10.7554/eLife.12454.001 PMID:27935480

Quasi-plane-hypothesis of strain coordination for RC beams seismically strengthened with externally-bonded or near-surface mounted fiber reinforced plastic

Science.gov (United States)

Ren, Zhenhua; Zeng, Xiantao; Liu, Hanlong; Zhou, Fengjun

2013-03-01

The application of fiber reinforced plastic (FRP), including carbon FRP and glass FRP, for structural repair and strengthening has grown due to their numerous advantages over conventional materials such as externally bonded reinforcement (EBR) and near-surface mounted (NSM) strengthening techniques. This paper summarizes the results from 21 reinforced concrete beams strengthened with different methods, including externally-bonded and near-surface mounted FRP, to study the strain coordination of the FRP and steel rebar of the RC beam. Since there is relative slipping between the RC beam and the FRP, the strain of the FRP and steel rebar of the RC beam satisfy the quasi-plane-hypothesis; that is, the strain of the longitudinal fiber that parallels the neutral axis of the plated beam within the scope of the effective height ( h 0) of the cross section is in direct proportion to the distance from the fiber to the neutral axis. The strain of the FRP and steel rebar satisfies the equation: ɛ FRP= βɛ steel, and the value of β is equal to 1.1-1.3 according to the test results.

Intensity modulated radiotherapy (IMRT) with compensators

International Nuclear Information System (INIS)

Salz, H.; Wiezorek, T.; Scheithauer, M.; Kleen, W.; Schwedas, M.; Wendt, T.G.

2002-01-01

The irradiation with intensity-modulated fields is possible with static as well as dynamic methods. In our university hospital, the intensity-modulated radiotherapy (IMRT) with compensators was prepared and used for the first time for patient irradiation in July 2001. The compensators consist of a mixture of tin granulate and wax, which is filled in a milled negative mould. The treatment planning is performed with Helax-TMS (MDS Nordion). An additional software is used for editing the modulation matrix ('Modifix'). Before irradiation of the first patient, extensive measurements have been carried out in terms of quality assurance of treatment planning and production of compensators. The results of the verification measurements have shown that IMRT with compensators possesses high spatial and dosimetric exactness. The calculated dose distributions are applied correctly. The accuracy of the calculated monitor units is normally better than 3%; in small volumes, further dosimetric inaccuracies between calculated and measured dose distributions are mostly less than 3%. Therefore, the compensators contribute to the achievement of high-level IMRT even when apparatuses without MLC are used. This paper describes the use of the IMRT with compensators, presents the limits of this technology, and discusses the first practical experiences. (orig.) [de

50 CFR 296.4 - Claims eligible for compensation.

Science.gov (United States)

2010-10-01

... compensation. (a) Claimants. Damage or loss eligible for Fund compensation must be suffered by a commercial fisherman. (b) Damage or loss of fishing gear. Damage or loss is eligible for Fund compensation if it was... is not eligible for Fund compensation: (1) If the damage or loss was caused by the negligence or...

Cooperative spreading processes in multiplex networks.

Science.gov (United States)

Wei, Xiang; Chen, Shihua; Wu, Xiaoqun; Ning, Di; Lu, Jun-An

2016-06-01

This study is concerned with the dynamic behaviors of epidemic spreading in multiplex networks. A model composed of two interacting complex networks is proposed to describe cooperative spreading processes, wherein the virus spreading in one layer can penetrate into the other to promote the spreading process. The global epidemic threshold of the model is smaller than the epidemic thresholds of the corresponding isolated networks. Thus, global epidemic onset arises in the interacting networks even though an epidemic onset does not arise in each isolated network. Simulations verify the analysis results and indicate that cooperative spreading processes in multiplex networks enhance the final infection fraction.

Quantification of rat brain SPECT with 123I-ioflupane: evaluation of different reconstruction methods and image degradation compensations using Monte Carlo simulation

International Nuclear Information System (INIS)

Roé-Vellvé, N; Pino, F; Cot, A; Ros, D; Falcon, C; Gispert, J D; Pavía, J; Marin, C

2014-01-01

SPECT studies with 123 I-ioflupane facilitate the diagnosis of Parkinson’s disease (PD). The effect on quantification of image degradations has been extensively evaluated in human studies but their impact on studies of experimental PD models is still unclear. The aim of this work was to assess the effect of compensating for the degrading phenomena on the quantification of small animal SPECT studies using 123 I-ioflupane. This assessment enabled us to evaluate the feasibility of quantitatively detecting small pathological changes using different reconstruction methods and levels of compensation for the image degrading phenomena. Monte Carlo simulated studies of a rat phantom were reconstructed and quantified. Compensations for point spread function (PSF), scattering, attenuation and partial volume effect were progressively included in the quantification protocol. A linear relationship was found between calculated and simulated specific uptake ratio (SUR) in all cases. In order to significantly distinguish disease stages, noise-reduction during the reconstruction process was the most relevant factor, followed by PSF compensation. The smallest detectable SUR interval was determined by biological variability rather than by image degradations or coregistration errors. The quantification methods that gave the best results allowed us to distinguish PD stages with SUR values that are as close as 0.5 using groups of six rats to represent each stage. (paper)

Spread effects - methodology; Spredningseffekter - metodegrunnlag

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

Diffusion of technology, environmental effects and rebound effects are the principal effects from the funding of renewable energy and energy economising. It is difficult to estimate the impact of the spread effects both prior to the measures are implemented and after the measures are carried out. Statistical methods can be used to estimate the spread effects, but they are insecure and always need to be complemented with qualitative and subjective evaluations. It is more adequate to evaluate potential spread effects from market and market data surveillance for a selection of technologies and parties. Based on this information qualitative indicators for spread effects can be constructed and used both ex ante and ex post (ml)

Design of the RTO/RC ITER primary pumping system

International Nuclear Information System (INIS)

Ladd, P.; Ibbott, C; Janeschitz, G.; Martin, E.

2000-01-01

The primary pumping system is needed not only to exhaust helium ash resulting from the DT reaction but also excess fuelling gas injected during the fusion burn, which can extend for 100's to 1000's of seconds, and to perform a variety of other functions. The prevailing environmental conditions, principally nuclear radiation, tritium exposure, magnetic fields, and the need for containment, have a significant impact on the design and selection of equipment. This paper presents the design of the Reduced Technical Objectives/Reduced Cost (RTO/RC) ITER primary pumping system with particular emphasis on the nuclear aspects of the design. Component selection and equipment layout issues to meet established requirements for the system are reviewed together with the R and D that is being undertaken to support the design. In addition, serviceability and maintainability issues related to this system are also discussed

Present and future activities of TRIGA RC-1 Reactor

International Nuclear Information System (INIS)

Festinesi, A.

1986-01-01

A summary of reactor activities is presented and discussed. The RC-1 reactor is used by ENEA's laboratories, research institutes and national industries for different aims: research, analysis materials behaviour under neutron flux, etc. To satisfy the requests increase it is important to signalize: - the realization of a new radiochemical laboratory for radioisotopes production, to be used in a medical and/or diagnostic field in general; - the realization of a tritium handling laboratory, to study tritium solubility, release and diffusion in different material (particularly in ceramic breeder as lithium aluminate) to support Italian programs on fusion technology; - a research activity on the reactors computerized control by a console of advanced conception. The aim of this activity is the development of an ergonomic control room that could be a reference point for the planning of the power reactor control rooms

EXTERNAL PRESTRESSING OF RC T-BEAMS WITH CFRP TENDONS

DEFF Research Database (Denmark)

Bennitz, Anders; Schmidt, Jacob Wittrup; Täljsten, Björn

2009-01-01

FRPs is about to become common practice. Several guidelines on the subject have been presented during the last decade, e.g. [1-5]. Next step is to further utilize the excellent behaviour of the advanced material, in particular CFRP (Carbon Fiber Reinforced Polymers). CFRPs have mechanical properties...... capacity could be increased, with a carefully applied compressive stress existing open cracks in concrete may be partly closed and it might also be possible to reduce large deflections. In that way the durability of the entire RC (Reinforced Concrete) -structure can be increased. Application of FRPs......As the acceptance for non-stressed FRP (Fibre Reinforced Polymers) increase steadily in the construction industry, the industries susceptibility for new ideas in the material’s usage increase. Improving the performance of a bridge, a parking garage or a multistory building by the use of appropriate...

Hysteretic MDOF Model to Quantify Damage for RC Shear Frames Subject to Earthquakes

DEFF Research Database (Denmark)

Köylüoglu, H. Ugur; Nielsen, Søren R.K.; Cakmak, Ahmet S.

A hysteretic mechanical formulation is derived to quantify local, modal and overall damage in reinforced concrete (RC) shear frames subject to seismic excitation. Each interstorey is represented by a Clough and Johnston (1966) hysteretic constitutive relation with degrading elastic fraction of th...... shear frame is subject to simulated earthquake excitations, which are modelled as a stationary Gaussian stochastic process with Kanai-Tajimi spectrum, multiplied by an envelope function. The relationship between local, modal and overall damage indices is investigated statistically....

14 CFR 250.8 - Denied boarding compensation.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Denied boarding compensation. 250.8 Section... PROCEEDINGS) ECONOMIC REGULATIONS OVERSALES § 250.8 Denied boarding compensation. (a) Every carrier shall tender to a passenger eligible for denied boarding compensation, on the day and place the denied boarding...

10 CFR 39.53 - Energy compensation source.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Energy compensation source. 39.53 Section 39.53 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.53 Energy compensation source. The licensee may use an energy compensation source (ECS) which is...

Interpersonal relationships and group A streptococcus spread in a Mexican day-care center Relaciones interpersonales y diseminación del estreptococo del grupo A (EGA en una guardería de México

Directory of Open Access Journals (Sweden)

Alberto Villaseñor-Sierra

2007-10-01

Full Text Available OBJECTIVE: To study the effect of different degrees of centrality on the carrying of identical group A streptococcus (GAS clones in the nasopharynx of children from a Mexican public day-care center. MATERIAL AND METHODS: Nasopharyngeal cultures were performed in children from rooms B (RB (n = 35 and C (RC (n = 37. The Restriction Fragment Length Polymorphism (RFLP patterns were compared among GAS isolates. A social networks questionnaire was filled out for each child and 10 classmates. Structure coefficients were compared among children with and without GAS. RESULTS: Four GAS clones were identified; clone I in five children from RC; clone II in two from RC and one from RB; clone III in one from RB and one from RC; and clone IV in one from RC. Social network structure: Density of RB and RC = 0.40 (± 0.87 and 0.35 (± 0.80, respectively. In RB, the homophily pattern of interaction was different in carriers (0.00, non-carriers (0.47 and both (0.47 p = 0.35. In RC, the homophily pattern was also different in carriers (0.46, non-carriers (0.68 and mixed (0.19, p = .001. In 4/5 with clone I, the values of degree, closeness and betweenness were above the group mean. In 3/3 with clone II, the values of degree and betweenness were also above the mean. In contrast, in those with clone III and IV, the values of degree, closeness and betweenness were below the group mean. CONCLUSION: The spread of specific GAS clones was associated with groups of children having a high proportion of ties and a high centrality level. This is evidence that spread of GAS strains among children attending day-care centers is not random but dependent on the degree of communication and physical contact between pairs.OBJETIVO: Evaluar el efecto de grados diferentes de centralidad con la presencia de clonas idénticas de estreptococo del grupo A (EGA en la nasofaringe de niños de una guardería pública de México. MATERIAL Y MÉTODOS: Se realizaron cultivos nasofaríngeos en ni

Effect of EMIC Wave Normal Angle Distribution on Relativistic Electron Scattering Based on the Newly Developed Self-consistent RC/EMIC Waves Model by Khazanov et al. [2006

Science.gov (United States)

Khazanov, G. V.; Gallagher, D. L.; Gamayunov, K.

2007-01-01

It is well known that the effects of EMIC waves on RC ion and RB electron dynamics strongly depend on such particle/wave characteristics as the phase-space distribution function, frequency, wave-normal angle, wave energy, and the form of wave spectral energy density. Therefore, realistic characteristics of EMIC waves should be properly determined by modeling the RC-EMIC waves evolution self-consistently. Such a selfconsistent model progressively has been developing by Khaznnov et al. [2002-2006]. It solves a system of two coupled kinetic equations: one equation describes the RC ion dynamics and another equation describes the energy density evolution of EMIC waves. Using this model, we present the effectiveness of relativistic electron scattering and compare our results with previous work in this area of research.

Evaluation of Shear Wall-RC Frame Interaction of High-Rise Buildings using 2-D model Approach

Directory of Open Access Journals (Sweden)

Dipali Patel

2015-09-01

Full Text Available The usefulness of structural walls in the framing of buildings has long been recognized. It is generally preferred to use shear wall in combination with moment resisting frame. In the present study, an effort is also made to investigate the shear wall-RC frame interaction using 2-D modeling of 20, 30 and 35 storey RC frame building with shear wall. In equivalent simplified 2-D model, two exterior frames with shear wall modeled as single frame with double stiffness, strength and weight. The interior frames without shear wall are modeled as a single frame with equivalent stiffness, strength and weight. The modeled frames are connected with rigid link at each floor level. Using 2-D plane frame model the lateral force distribution between Exterior frame with shear wall and Interior frame without shear wall is investigated. From the analysis, it is observed that up to bottom seven/eight storey more than 50% load is taken by frame with shear wall and the lower most three storeys take about 75% of total storey shear.

Fluorescent visualization of a spreading surfactant

Energy Technology Data Exchange (ETDEWEB)

Fallest, David W; Lichtenberger, Adele M; Fox, Christopher J; Daniels, Karen E, E-mail: kdaniel@ncsu.ed [Department of Physics, North Carolina State University, Raleigh, NC 27695 (United States)

2010-07-15

The spreading of surfactants on thin films is an industrially and medically important phenomenon, but the dynamics are highly nonlinear and visualization of the surfactant dynamics has been a long-standing experimental challenge. We perform the first quantitative, spatiotemporally resolved measurements of the spreading of an insoluble surfactant on a thin fluid layer. During the spreading process, we directly observe both the radial height profile of the spreading droplet and the spatial distribution of the fluorescently tagged surfactant. We find that the leading edge of a spreading circular layer of surfactant forms a Marangoni ridge in the underlying fluid, with a trough trailing the ridge as expected. However, several novel features are observed using the fluorescence technique, including a peak in the surfactant concentration that trails the leading edge, and a flat, monolayer-scale spreading film that differs from concentration profiles predicted by current models. Both the Marangoni ridge and the surfactant leading edge can be described to spread as R{approx}t{sup {delta}}. We find spreading exponents {delta}{sub H}{approx}0.30 and {delta}{sub {Gamma}}{approx}0.22 for the ridge peak and surfactant leading edge, respectively, which are in good agreement with theoretical predictions of {delta}=1/4. In addition, we observe that the surfactant leading edge initially leads the peak of the Marangoni ridge, with the peak later catching up to the leading edge.

Standard compensation for power cuts. Working group report

International Nuclear Information System (INIS)

2002-07-01

The Working Group was commissioned to draw up a proposal in the form of a Government Bill for provisions to be included in the Electricity Market Act on imposing an obligation on the distribution net operator to pay a standard compensation to the users of electricity for the event that they get no access to electricity. The Working Group should consider especially a model of standard compensation presented in the final report by Mr. Jarl Forsten, Deputy Director General of the Technical Research Centre of Finland VTT, published on 30 April 2002 that the amount of standard compensation should not depend on the reason for the power cut. The Working Group proposes that the Electricity Market Act should be amended by provisions providing that a distribution net operator shall pay to the user of electricity a standard compensation for power cuts lasting over 12 hours. The amount of compensation shall be based on the annual network service fee and a sliding scale of compensation related to the duration of the power cut shall be applied. The maximum compensation shall be paid when the power cut lasts more than five days. The maximum amount of individual compensations shall be fixed at EUR 700. The proposed provisions on standard compensation in the event of power cuts are aimed at amending the provisions in Chapter 6a of the Electricity Market Act on price reduction and compensation because of fault in the supply of electricity. The aim of the introduction of standard compensation for power cuts is to persuade distribution net operators to make an effort to minimize the time for power cuts. (orig.)

Engineering Compensations in Web Service Environment

DEFF Research Database (Denmark)

Schäfer, Micahel; Dolog, Peter; Nejdl, Wolfgang

2007-01-01

Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure in such a......Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure...... in such an environment occurs, a compensation can be initiated to recover from the failure. However, current environments have only limited capabilities for compensations, and are usually based on backward recovery. In this paper, we introduce an engineering approach and an environment to deal with advanced...... compensations based on forward recovery principles. We extend the existing Web service transaction coordination architecture and infrastructure in order to support flexible compensation operations. A contract-based approach is being used, which allows the specification of permitted compensations at runtime. We...

Changing Conceptions of Employee Compensation

Science.gov (United States)

Dixon, Mark R.; Hayes, Linda J.

2004-01-01

This paper reviews and discusses many differing forms of incentive compensation systems that are being used in today's organizations. The review traces the roots of bonus compensation from individual piece-work plans through the adoption of organization-wide gain sharing plans to the growing recognition of open-book management. Reasons for the…

29 CFR 505.3 - Prevailing minimum compensation.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Prevailing minimum compensation. 505.3 Section 505.3 Labor... HUMANITIES § 505.3 Prevailing minimum compensation. (a)(1) In the absence of an alternative determination...)(2) of this section, the prevailing minimum compensation required to be paid under the Act to the...

Terrestrial spreading centers under Venus conditions - Evaluation of a crustal spreading model for Western Aphrodite Terra

Science.gov (United States)

Sotin, C.; Senske, D. A.; Head, J. W.; Parmentier, E. M.

1989-01-01

The model of Reid and Jackson (1981) for terrestrial spreading centers is applied to Venus conditions. On the basis of spreading rate, mantle temperature, and surface temperature, the model predicts both isostatic topography and crustal thickness. The model and Pioneer Venus altimetry and gravity data are used to test the hypothesis of Head and Crumpler (1987) that Western Aphrodite Terra is the location of crustal spreading on Venus. It is concluded that a spreading center model for Ovda Regio in Western Aphrodite Terra could account for the observed topography and line-of-sight gravity anomalies found in the Pioneer data.

Derivation of the human embryonic stem cell line RCe014-A (RC-10

Directory of Open Access Journals (Sweden)

P.A. De Sousa

2016-03-01

Full Text Available The human embryonic stem cell line RCe014-A (RC-10 was derived from a fresh oocyte voluntarily donated as unsuitable and surplus to fertility requirements following ethics committee approved informed consent under licence from the UK Human Fertilisation and Embryology Authority. The cell line shows normal pluripotency marker expression and differentiation to the three germ layers in vitro. It has a mixed 46XY and 47XY +12 male karyotype and microsatellite PCR identity, HLA and blood group typing data is available.

Derivation of the human embryonic stem cell line RCe010-A (RC-6

Directory of Open Access Journals (Sweden)

P.A. De Sousa

2016-03-01

Full Text Available The human embryonic stem cell line RCe010-A (RC-6 was derived from a frozen and thawed blastocyst voluntarily donated as unsuitable and surplus to fertility requirements following ethics committee approved informed consent under licence from the UK Human Fertilisation and Embryology Authority. The cell line shows normal pluripotency marker expression and differentiation to the three germ layers in vitro. It has a normal 46XY male karyotype and microsatellite PCR identity, HLA and blood group typing data are available.

Vibration based structural assessment of the rehabilitation intervention in r.c. segmental bridge

OpenAIRE

Franchetti Paolo; Frizzarin Michele; Leonardi Andrea; Zeni Fabio

2015-01-01

A vibration based structural assessment campaign was carried out on a r.c. segmental bridge in North East Italy. The bridge has a cantilever static scheme, fixed at the top of the piers and with a hinge at the centre of the span. The particular configuration of the hinge consists in a couple of steel elements, each one composed by a tongue and groove joint. Since the year 1960, the hinge was subjected to consumption and degradation, that caused a malfunctioning of the device. An intervention ...

39 CFR 3.2 - Compensation of Board.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Compensation of Board. 3.2 Section 3.2 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE BOARD OF GOVERNORS (ARTICLE III) § 3.2 Compensation of Board. Section 202(a)(1) of title 39 provides for the compensation of...

26 CFR 31.3231(e)-1 - Compensation.

Science.gov (United States)

2010-04-01

.... (a) Definition—(1) The term compensation has the same meaning as the term wages in section 3121(a... regarding the inclusion of fringe benefits in compensation, see § 31.3121(a)-1T. (6) Split-dollar life... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Compensation. 31.3231(e)-1 Section 31.3231(e)-1...

33 CFR 136.223 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS... allowable under paragraph (a) of this section must be reduced by— (1) All compensation made available to the... under § 136.235. Government Revenues ...

Humidity build-up in electronic enclosures exposed to different geographical locations by RC modelling and reliability prediction

DEFF Research Database (Denmark)

Conseil-Gudla, H.; Staliulionis, Z.; Mohanty, S.

2018-01-01

according to this steady state (25 °C and 60% RH) have been calculated for the different climates, and the protection offered by the enclosures has been estimated under different casing materials and resistor-capacitor (RC) simulation. This method offers a way to predict the average value of failure rate...

Compensation of Disadvantages in University Examination Procedures

Directory of Open Access Journals (Sweden)

Ulrike Quapp

2016-08-01

Full Text Available Active social participation of disabled people is one of the major tasks of modern society. That also includes access to the academic community by higher education. Universities all over the world work hard to give handicapped students a chance to graduate. In this context, compensation of disadvantages in examination procedures is an important matter. But, also chronic illness may impair the student's examination performance. To ensure equal examination opportunities for all students, responsible university officials must be creative to find individual compensation solutions. The paper analyzes examination regulations at universities in different countries and offers solutions to compensate disabled and chronic ill students' disadvantages. It discusses the necessity of compensation for different types of disability and chronic illness. Finally, an overview of current German case law and solutions for compensation problems are provided.

Spreading to localized targets in complex networks

Science.gov (United States)

Sun, Ye; Ma, Long; Zeng, An; Wang, Wen-Xu

2016-12-01

As an important type of dynamics on complex networks, spreading is widely used to model many real processes such as the epidemic contagion and information propagation. One of the most significant research questions in spreading is to rank the spreading ability of nodes in the network. To this end, substantial effort has been made and a variety of effective methods have been proposed. These methods usually define the spreading ability of a node as the number of finally infected nodes given that the spreading is initialized from the node. However, in many real cases such as advertising and news propagation, the spreading only aims to cover a specific group of nodes. Therefore, it is necessary to study the spreading ability of nodes towards localized targets in complex networks. In this paper, we propose a reversed local path algorithm for this problem. Simulation results show that our method outperforms the existing methods in identifying the influential nodes with respect to these localized targets. Moreover, the influential spreaders identified by our method can effectively avoid infecting the non-target nodes in the spreading process.

Comparison of Cloud Detection Using the CERES-MODIS Ed4 and LaRC AVHRR Cloud Masks and CALIPSO Vertical Feature Mask

Science.gov (United States)

Trepte, Q. Z.; Minnis, P.; Palikonda, R.; Bedka, K. M.; Sun-Mack, S.

2011-12-01

Accurate detection of cloud amount and distribution using satellite observations is crucial in determining cloud radiative forcing and earth energy budget. The CERES-MODIS (CM) Edition 4 cloud mask is a global cloud detection algorithm for application to Terra and Aqua MODIS data with the aid of other ancillary data sets. It is used operationally for the NASA's Cloud and Earth's Radiant Energy System (CERES) project. The LaRC AVHRR cloud mask, which uses only five spectral channels, is based on a subset of the CM cloud mask which employs twelve MODIS channels. The LaRC mask is applied to AVHRR data for the NOAA Climate Data Record Program. Comparisons among the CM Ed4, and LaRC AVHRR cloud masks and the CALIPSO Vertical Feature Mask (VFM) constitute a powerful means for validating and improving cloud detection globally. They also help us understand the strengths and limitations of the various cloud retrievals which use either active and passive satellite sensors. In this paper, individual comparisons will be presented for different types of clouds over various surfaces, including daytime and nighttime, and polar and non-polar regions. Additionally, the statistics of the global, regional, and zonal cloud occurrence and amount from the CERES Ed4, AVHRR cloud masks and CALIPSO VFM will be discussed.

Predicting the seismic performance of typical R/C healthcare facilities: emphasis on hospitals

Science.gov (United States)

Bilgin, Huseyin; Frangu, Idlir

2017-09-01

Reinforced concrete (RC) type of buildings constitutes an important part of the current building stock in earthquake prone countries such as Albania. Seismic response of structures during a severe earthquake plays a vital role in the extent of structural damage and resulting injuries and losses. In this context, this study evaluates the expected performance of a five-story RC healthcare facility, representative of common practice in Albania, designed according to older codes. The design was based on the code requirements used in this region during the mid-1980s. Non-linear static and dynamic time history analyses were conducted on the structural model using the Zeus NL computer program. The dynamic time history analysis was conducted with a set of ground motions from real earthquakes. The building responses were estimated in global levels. FEMA 356 criteria were used to predict the seismic performance of the building. The structural response measures such as capacity curve and inter-story drift under the set of ground motions and pushover analyses results were compared and detailed seismic performance assessment was done. The main aim of this study is considering the application and methodology for the earthquake performance assessment of existing buildings. The seismic performance of the structural model varied significantly under different ground motions. Results indicate that case study building exhibit inadequate seismic performance under different seismic excitations. In addition, reasons for the poor performance of the building is discussed.

Estimation of wave directional spreading

Digital Repository Service at National Institute of Oceanography (India)

Deo, M.C.; Gondane, D.S.; SanilKumar, V.

One of the useful measures of waves directional spreading at a given location is the directional spreading parameter. This paper presents a new approach to arrive at its characteristic value using the computational technique of Artificial Neural...

Dose compensation of the total body irradiation therapy

International Nuclear Information System (INIS)

Lin, J.-P.; Chu, T.-C.; Liu, M.-T.

2001-01-01

The aim of the study is to improve dose uniformity in the body by the compensator-rice and to decrease the dose to the lung by the partial lung block. Rando phantom supine was set up to treat bilateral fields with a 15 MV linear accelerator at 415 cm treatment distance. The experimental procedure included three parts. The first part was the bilateral irradiation without rice compensator, and the second part was with rice compensator. In the third part, rice compensator and partial lung block were both used. The results of thermoluminescent dosimeters measurements indicated that without rice compensator the dose was non-uniform. Contrarily, the average dose homogeneity with rice compensator was measured within ±5%, except for the thorax region. Partial lung block can reduce the dose which the lung received. This is a simple method to improve the dose homogeneity and to reduce the lung dose received. The compensator-rice is cheap, and acrylic boxes are easy to obtain. Therefore, this technique is suitable for more studies

Aeromagnetic Compensation Algorithm Based on Principal Component Analysis

Directory of Open Access Journals (Sweden)

Peilin Wu

2018-01-01

Full Text Available Aeromagnetic exploration is an important exploration method in geophysics. The data is typically measured by optically pumped magnetometer mounted on an aircraft. But any aircraft produces significant levels of magnetic interference. Therefore, aeromagnetic compensation is important in aeromagnetic exploration. However, multicollinearity of the aeromagnetic compensation model degrades the performance of the compensation. To address this issue, a novel aeromagnetic compensation method based on principal component analysis is proposed. Using the algorithm, the correlation in the feature matrix is eliminated and the principal components are using to construct the hyperplane to compensate the platform-generated magnetic fields. The algorithm was tested using a helicopter, and the obtained improvement ratio is 9.86. The compensated quality is almost the same or slightly better than the ridge regression. The validity of the proposed method was experimentally demonstrated.

Spreading gossip in social networks

Science.gov (United States)

Lind, Pedro G.; da Silva, Luciano R.; Andrade, José S., Jr.; Herrmann, Hans J.

2007-09-01

We study a simple model of information propagation in social networks, where two quantities are introduced: the spread factor, which measures the average maximal reachability of the neighbors of a given node that interchange information among each other, and the spreading time needed for the information to reach such a fraction of nodes. When the information refers to a particular node at which both quantities are measured, the model can be taken as a model for gossip propagation. In this context, we apply the model to real empirical networks of social acquaintances and compare the underlying spreading dynamics with different types of scale-free and small-world networks. We find that the number of friendship connections strongly influences the probability of being gossiped. Finally, we discuss how the spread factor is able to be applied to other situations.

Spreading gossip in social networks.

Science.gov (United States)

Lind, Pedro G; da Silva, Luciano R; Andrade, José S; Herrmann, Hans J

2007-09-01

We study a simple model of information propagation in social networks, where two quantities are introduced: the spread factor, which measures the average maximal reachability of the neighbors of a given node that interchange information among each other, and the spreading time needed for the information to reach such a fraction of nodes. When the information refers to a particular node at which both quantities are measured, the model can be taken as a model for gossip propagation. In this context, we apply the model to real empirical networks of social acquaintances and compare the underlying spreading dynamics with different types of scale-free and small-world networks. We find that the number of friendship connections strongly influences the probability of being gossiped. Finally, we discuss how the spread factor is able to be applied to other situations.

Ion implantation damage annealing in 4H-SiC monitored by scanning spreading resistance microscopy

International Nuclear Information System (INIS)

Suchodolskis, A.; Hallen, A.; Linnarsson, M.K.; Osterman, J.; Karlsson, U.O.

2006-01-01

To obtain a better understanding of the damage annealing process and dopant defect incorporation and activation we have implanted epitaxially grown 4H-SiC layers with high doses of Al + ions. Cross-sections of the samples are investigated by scanning spreading resistance microscopy (SSRM) using a commercial atomic force microscopy (AFM). The defects caused by the implanted ions compensate for the doping and decrease the charge carrier mobility. This causes the resistivity to increase in the as-implanted regions. The calculated profile of implanted ions is in good agreement with the measured ones and shows a skewed Gaussian shape. Implanted samples are annealed up to 400 deg. C. Despite these low annealing temperatures we observe a clear improvement of the sample conductivity in the as-implanted region

Derivation of the human embryonic stem cell line RCe006-A (RC-2

Directory of Open Access Journals (Sweden)

P.A. De Sousa

2016-03-01

Full Text Available The human embryonic stem cell line RCe006-A (RC-2 was derived from a frozen and thawed blastocyst voluntarily donated as surplus to fertility requirements following ethics committee approved informed consent under licence from the UK Human Fertilisation and Embryology Authority. The cell line exhibits expression of expected pluripotency markers and in vitro differentiation potential to three germinal lineage representative cell populations. It has a male trisomy 12 karyotype (47XY, +12. Microsatellite DNA marker identity and HLA and blood group typing data are available.

Derivation of the human embryonic stem cell line RCe012-A (RC-8

Directory of Open Access Journals (Sweden)

P.A. De Sousa

2016-03-01

Full Text Available The human embryonic stem cell line RCe012-A (RC-8 was derived from a frozen and thawed day 5 embryo cultivated to the blastocyst stage. The embryo was voluntarily donated as unsuitable and surplus to fertility requirements following ethics committee approved informed consent under licence from the UK Human Fertilisation and Embryology Authority. The cell line shows normal pluripotency marker expression and differentiation to the three germ layers in vitro. It has a normal 46XX female karyotype and microsatellite PCR identity, HLA and blood group typing data is available.

COMBINED SURGERY OF SPREAD THYROID CANCER

Directory of Open Access Journals (Sweden)

V. Zh. Brzhezovsky

2014-01-01

Full Text Available Results of treating of 99 patients with differentiated thyroid cancer spreading beyond the capsule of the organ were analysed. In most cases with spreading the tumor to the tracheal rings performing of organ-preserving operations (from “window-like” tracheal resections to circular tracheal resection with intertracheal anastomosis is possible. Choosing of type of operation to be performed depends on localisation and spread of tumor invasion of trachea, pharynx and esophagus. Using of combined operations in patients with locally-spread thyroid cancer allows to achieve long and stable remission in most of the cases.

Seismic assessment of existing RC buildings under alternative ground motion ensembles compatible to EC8 and NTC 2008

NARCIS (Netherlands)

Tanganelli, Marco; Viti, Stefania; Mariani, V.; Pianigiani, Maria

2017-01-01

This work investigates the effects of the choice of different ensembles of ground motions on the seismic assessment of existing RC buildings through nonlinear dynamic analysis. Nowadays indeed, all the main International Seismic Codes provide a soil classification which is based on the shear wave

Forest Ecosystem Services and Eco-Compensation Mechanisms in China

Science.gov (United States)

Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

2011-12-01

Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

Forest ecosystem services and eco-compensation mechanisms in China.

Science.gov (United States)

Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

2011-12-01

Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

Development of a 3D optical scanning-based automatic quality assurance system for proton range compensators

International Nuclear Information System (INIS)

Kim, MinKyu; Ju, Sang Gyu; Chung, Kwangzoo; Hong, Chae-Seon; Kim, Jinsung; Ahn, Sung Hwan; Jung, Sang Hoon; Han, Youngyih; Chung, Yoonsun; Cho, Sungkoo; Choi, Doo Ho; Kim, Jungkuk; Shin, Dongho

2015-01-01

Purpose: A new automatic quality assurance (AutoRCQA) system using a three-dimensional scanner (3DS) with system automation was developed to improve the accuracy and efficiency of the quality assurance (QA) procedure for proton range compensators (RCs). The system performance was evaluated for clinical implementation. Methods: The AutoRCQA system consists of a three-dimensional measurement system (3DMS) based on 3DS and in-house developed verification software (3DVS). To verify the geometrical accuracy, the planned RC data (PRC), calculated with the treatment planning system (TPS), were reconstructed and coregistered with the measured RC data (MRC) based on the beam isocenter. The PRC and MRC inner surfaces were compared with composite analysis (CA) using 3DVS, using the CA pass rate for quantitative analysis. To evaluate the detection accuracy of the system, the authors designed a fake PRC by artificially adding small cubic islands with side lengths of 1.5, 2.5, and 3.5 mm on the inner surface of the PRC and performed CA with the depth difference and distance-to-agreement tolerances of [1 mm, 1 mm], [2 mm, 2 mm], and [3 mm, 3 mm]. In addition, the authors performed clinical tests using seven RCs [computerized milling machine (CMM)-RCs] manufactured by CMM, which were designed for treating various disease sites. The systematic offsets of the seven CMM-RCs were evaluated through the automatic registration function of AutoRCQA. For comparison with conventional technique, the authors measured the thickness at three points in each of the seven CMM-RCs using a manual depth measurement device and calculated thickness difference based on the TPS data (TPS-manual measurement). These results were compared with data obtained from 3DVS. The geometrical accuracy of each CMM-RC inner surface was investigated using the TPS data by performing CA with the same criteria. The authors also measured the net processing time, including the scan and analysis time. Results: The Auto

A Novel Time-Varying Friction Compensation Method for Servomechanism

Directory of Open Access Journals (Sweden)

Bin Feng

2015-01-01

Full Text Available Friction is an inevitable nonlinear phenomenon existing in servomechanisms. Friction errors often affect their motion and contour accuracies during the reverse motion. To reduce friction errors, a novel time-varying friction compensation method is proposed to solve the problem that the traditional friction compensation methods hardly deal with. This problem leads to an unsatisfactory friction compensation performance and the motion and contour accuracies cannot be maintained effectively. In this method, a trapezoidal compensation pulse is adopted to compensate for the friction errors. A generalized regression neural network algorithm is used to generate the optimal pulse amplitude function. The optimal pulse duration function and the pulse amplitude function can be established by the pulse characteristic parameter learning and then the optimal friction compensation pulse can be generated. The feasibility of friction compensation method was verified on a high-precision X-Y worktable. The experimental results indicated that the motion and contour accuracies were improved greatly with reduction of the friction errors, in different working conditions. Moreover, the overall friction compensation performance indicators were decreased by more than 54% and this friction compensation method can be implemented easily on most of servomechanisms in industry.

Epidemic spreading through direct and indirect interactions.

Science.gov (United States)

Ganguly, Niloy; Krueger, Tyll; Mukherjee, Animesh; Saha, Sudipta

2014-09-01

In this paper we study the susceptible-infected-susceptible epidemic dynamics, considering a specialized setting where popular places (termed passive entities) are visited by agents (termed active entities). We consider two types of spreading dynamics: direct spreading, where the active entities infect each other while visiting the passive entities, and indirect spreading, where the passive entities act as carriers and the infection is spread via them. We investigate in particular the effect of selection strategy, i.e., the way passive entities are chosen, in the spread of epidemics. We introduce a mathematical framework to study the effect of an arbitrary selection strategy and derive formulas for prevalence, extinction probabilities, and epidemic thresholds for both indirect and direct spreading. We also obtain a very simple relationship between the extinction probability and the prevalence. We pay special attention to preferential selection and derive exact formulas. The analysis reveals that an increase in the diversity in the selection process lowers the epidemic thresholds. Comparing the direct and indirect spreading, we identify regions in the parameter space where the prevalence of the indirect spreading is higher than the direct one.

Seismic Retrofitting: Reinforced Concrete (RC shear wall versus Reinforcement of RC element by Carbon Fiber Reinforced Polymer (CFRP using PUSHOVER analysis

Directory of Open Access Journals (Sweden)

Yahya RIYAD

2016-12-01

Full Text Available Seismic retrofitting of constructions vulnerable to earthquakes is a current problem of great political and social relevance. During the last sixty years, moderate to severe earthquakes have occurred in Morocco (specifically in Agadir 1960 and Hoceima 2004. Such events have clearly shown the vulnerability of the building stock in particular and of the built environment in general. Hence, it is very much essential to retrofit the vulnerable building to cope up for the next damaging earthquake. In this paper, the focus will be on a comparative study between two techniques of seismic retrofitting, the first one is a reinforcement using carbon fiber reinforced polymer (CFRP applied to RC elements by bonding , and the second one is a reinforcement with a shear wall. For this study, we will use a non-linear static analysis -also known as Pushover analysis - on a reinforced concrete structure consisting of beams and columns, and composed from eight storey with a gross area of 240 m², designed conforming to the Moroccan Seismic code[1].

An Implementation of RC4+ Algorithm and Zig-zag Algorithm in a Super Encryption Scheme for Text Security

Science.gov (United States)

Budiman, M. A.; Amalia; Chayanie, N. I.

2018-03-01

Cryptography is the art and science of using mathematical methods to preserve message security. There are two types of cryptography, namely classical and modern cryptography. Nowadays, most people would rather use modern cryptography than classical cryptography because it is harder to break than the classical one. One of classical algorithm is the Zig-zag algorithm that uses the transposition technique: the original message is unreadable unless the person has the key to decrypt the message. To improve the security, the Zig-zag Cipher is combined with RC4+ Cipher which is one of the symmetric key algorithms in the form of stream cipher. The two algorithms are combined to make a super-encryption. By combining these two algorithms, the message will be harder to break by a cryptanalyst. The result showed that complexity of the combined algorithm is θ(n2 ), while the complexity of Zig-zag Cipher and RC4+ Cipher are θ(n2 ) and θ(n), respectively.

Ductility Analysis of RC Beams Considering the Concrete Confinement Effect Produced by the Shear Reinforcement: a Numerical Approach

Directory of Open Access Journals (Sweden)

Caio Gorla Nogueira

Full Text Available Abstract In this paper, a simplified numerical approach to study the influence of the confinement effect provided by transversal reinforcement on the ductility behavior of RC beams in bending is proposed. A unidimensional FEM mechanical model coupled to the Mazars’ damage model to simulate concrete behavior was adopted to assess ductility curvatures at the ultimate limit state. The confinement effect was incorporated to the numerical model through a calibration process of the damage internal parameters, based on the Least Square Method and an analytical law proposed by Kent and Park (1971. Several numerical analyses were carried out considering different designs of RC beams according to a parametric study varying the neutral axis position, concrete compressive strength and the volumetric transversal reinforcement ratio. The obtained results showed the importance of the amount of transversal reinforcement on the ductility behavior, increasing the ductility factor even for the cases with inappropriate neutral axis position.

33 CFR 136.211 - Compensation allowable.

Science.gov (United States)

2010-07-01

...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.211 Compensation... that amount required to accomplish the activities for which the claim was paid. Real or Personal...

Metabolic Compensation of Fitness Costs Is a General Outcome for Antibiotic-Resistant Pseudomonas aeruginosa Mutants Overexpressing Efflux Pumps.

Science.gov (United States)

Olivares Pacheco, Jorge; Alvarez-Ortega, Carolina; Alcalde Rico, Manuel; Martínez, José Luis

2017-07-25

It is generally assumed that the acquisition of antibiotic resistance is associated with a fitness cost. We have shown that overexpression of the MexEF-OprN efflux pump does not decrease the fitness of a resistant Pseudomonas aeruginosa strain compared to its wild-type counterpart. This lack of fitness cost was associated with a metabolic rewiring that includes increased expression of the anaerobic nitrate respiratory chain when cells are growing under fully aerobic conditions. It was not clear whether this metabolic compensation was exclusive to strains overexpressing MexEF-OprN or if it extended to other resistant strains that overexpress similar systems. To answer this question, we studied a set of P. aeruginosa mutants that independently overexpress the MexAB-OprM, MexCD-OprJ, or MexXY efflux pumps. We observed increased expression of the anaerobic nitrate respiratory chain in all cases, with a concomitant increase in NO 3 consumption and NO production. These efflux pumps are proton/substrate antiporters, and their overexpression may lead to intracellular H + accumulation, which may in turn offset the pH homeostasis. Indeed, all studied mutants showed a decrease in intracellular pH under anaerobic conditions. The fastest way to eliminate the excess of protons is by increasing oxygen consumption, a feature also displayed by all analyzed mutants. Taken together, our results support metabolic rewiring as a general mechanism to avoid the fitness costs derived from overexpression of P. aeruginosa multidrug efflux pumps. The development of drugs that block this metabolic "reaccommodation" might help in reducing the persistence and spread of antibiotic resistance elements among bacterial populations. IMPORTANCE It is widely accepted that the acquisition of resistance confers a fitness cost in such a way that in the absence of antibiotics, resistant populations will be outcompeted by susceptible ones. Based on this assumption, antibiotic cycling regimes have been

Crime victims‘ right to compensation

Directory of Open Access Journals (Sweden)

Mrvić-Petrović Nataša

2012-01-01

Full Text Available This paper analyzes the most important documents of the United Nations, Council of Europe and the European Union relating to rights to damage compensation (restitution from offender and state compensation. The analysis shows that there is a gradual move from the concept of exercising the rights of victims in favor of a solidaristic model that takes less into account the rights of victims, and more the need to satisfy their legitimate interests. The economic crisis that is undermining the foundations of the welfare state could jeopardize the realization of this concept, especially in those European countries where the criminal justice system focuses solely on the offender, as is the case in Serbia. In such circumstances, regulation which protects the right to compensation, other rights and interests of victims, shall apply only to the extent that serves crime prevention. So it happens that in spite of a suitable normative framework and developments regarding the protection of victims of domestic violence and trafficking, the right to compensation and other rights of the victims do not actually get actualized in practice. In order to overcome this, a systemic reform to the criminal justice system should be undertaken with the aim to redirect the system towards the victim of the offense. Within these reforms a public fund for compensation of the victims of violence should be established and the process of mediation between the victim and the offender with the goal to make a settlement should be regulated, because these mechanisms do not exist in Serbia.

A More Sustainable Way for Producing RC Sandwich Panels On-Site and in Developing Countries

Directory of Open Access Journals (Sweden)

Lorenzo Graziani

2017-03-01

Full Text Available The purpose of this work is to assess if traditionally used welded connectors for joining the two skins of reinforced concrete (RC sandwich panels, used as structural walls and horizontal structural elements, can be substituted with bent ones. In this way, the scope of the effort is to reduce drastically the energy required during manufacturing, thus having a much more sustainable building product. Wire mesh on site production, in fact, requires a large amount of energy for the welding process, as stated by several Environmental Product Declaration (EPD. In addition, the production of sandwich panels with bent connectors requires a low level of automation and no qualified labor allowing the diffusion in developing countries. The procedures used to execute the work were both experimental and numerical. Structural performances were examined by testing full-scale sandwich panels under (axial and eccentric compression and flexural loads. Additionally, a Finite Element (FE study was developed to investigate and to optimize the dimension of welded mesh and the number of connectors. The major findings show that it is possible to substitute welded connectors with bent ones without compromising the structural performance of the tested RC sandwich panels, thus having a more sustainable way for producing these last ones.

Effect of discrete glass fibers on the behavior of R.C. Beams exposed to fire

Directory of Open Access Journals (Sweden)

Magdy Riad

2017-08-01

Full Text Available The main objective of this paper is to investigate the effect of adding discrete glass fibers on the behavior of reinforced concrete (RC beams under different fire and cooling conditions. Eighteen beams with different concrete compressive strengths were tested to study the behavior of reinforced concrete (RC beams containing discrete glass fibers when exposed to different fire and cooling conditions. Nine beams were prepared from normal strength concrete (NSC with compressive strength equal to 35 MPa while the other beams were prepared from high strength concrete (HSC with compressive strength equal to 60 MPa. The beams contained different contents of discrete glass fibers. The modes of failure of tested specimens show that the crack patterns change according to fire condition and fiber content. Analysis of test results show that adding discrete glass fibers to NSC increased the residual stiffness of the tested specimens after firing and decreased the rate of the deflection gain during firing. Also adding fibers to concrete has a limited positive effect on the ultimate strength of the specimens compared to the control specimens. Its effect on deflection due to fire is more pronounced. Finally, the recommended optimum ratio of discrete glass fibers is not more than 0.5% of the total concrete weight.

20 CFR 25.101 - How is compensation for death paid?

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false How is compensation for death paid? 25.101... EMPLOYEES' COMPENSATION ACT COMPENSATION FOR DISABILITY AND DEATH OF NONCITIZEN FEDERAL EMPLOYEES OUTSIDE THE UNITED STATES The Special Schedule of Compensation § 25.101 How is compensation for death paid? If...

A numerical design approach for single amplifier, Active-RC Butterworth filter of order 5

OpenAIRE

Gaunholt, Hans

2007-01-01

A design method is presented for the design of all pole lowpass active-RC filters applying operational amplifiers. The operational amplifier model used is the integrator model: omegat/s where omegat is the unity gain frequency. The design method is used for the design of a fifth order Butterworth filter applying just one operational amplifier coupled as a unity gain amplifier. It is shown that the influence from the real operational amplifier may be reduced by trimming just one resistor in th...

To the issue of increasing efficiency of VAR compensation

Directory of Open Access Journals (Sweden)

Світлана Костянтинівна Поднебенна

2015-11-01

Full Text Available This article describes the features of VAR compensation of variable loads. One of the most common non-symmetric non-linear power consumers are welding power sources. Time and duration of the work of these sources vary randomly. To compensate the consumption of reactive power on the basis of consumption data from the three-phase electricity meters is inefficient. Compensation devices power should be calculated taking into account the asymmetrical consumption/generation of reactive power per phase and changing consumption patterns. Thyristor-controlled reactor, thyristor-switched capacitors, hybrid VAR compensators, active compensators (STATCOMs, «dynamic capacitors» can be used as the VAR compensation devices. Thyristor-controlled reactors can provide smooth regulation of reactive power, but they have high weight and size parameters and are additional sources of higher harmonics. Thyristor-switched capacitors provide stepwise adjustment of reactive power and are subject to the current higher harmonics. Hybrid VAR compensators make it possible to isolate capacitors from the higher harmonics and ensure smooth regulation, which is achieved by active filter introduction to the reactive power compensation devices based on thyristor-switched capacitors. However, this increases the cost of a compensator and complicates its control system. STATCOMs provide smooth regulation of reactive power, but they are too expensive.Perspective direction in the development of effective VAR compensation devices is «dynamic capacitor». As a result of a feasibility study the prospects for further research of electrical grids power efficiency through the development of effective devices for VAR compensation have been established

Passive cooling effect of RC roof covered with the ceramics having high water retention and evaporation capacity

International Nuclear Information System (INIS)

Yamazaki, M; Kanaya, M; Shimazu, T; Ohashi, T; Kato, N; Horikoshi, T

2011-01-01

Hot days in metropolitan cities have increased remarkably by the heat island phenomenon these days. Thus the authors tried to develop the porous ceramics with high water retention and evaporation capacity as a maintenance-free material to improve thermal environment. The developed ceramic pellets have high water retention of more than 60% of water absorption and high water evaporation which is similar to water surface. In this study, three types of 5 meter squared large flat-roofed structural specimen simulated reinforced concrete (RC) slab were constructed on the outside. The variation of water content and temperature of the specimens and atmosphere temperature around the specimens were measured from summer in 2009. In the case of the ceramic pellets, the temperature under RC slab was around 15 deg. lower than that of the control. The results were probably contributed by passive cooling effect of evaporated rain water, and the effect was similar to in the case of the grasses. From the viewpoint of thermal environment improvement, substitution of a rooftop gardening by the porous ceramics could be a promising method.

Passive cooling effect of RC roof covered with the ceramics having high water retention and evaporation capacity

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, M; Kanaya, M; Shimazu, T; Ohashi, T [INAX Corporation, 97-1, Yariba, Kume, Tokoname, Aichi, 479-0002 (Japan); Kato, N; Horikoshi, T, E-mail: m.yamazaki@i2.inax.co.jp [Department of Architecture, Nagoya Institute of technology, Gokiso-cho, Showa-ku, Nagoya, Aichi, 466-8555 (Japan)

2011-10-29

Hot days in metropolitan cities have increased remarkably by the heat island phenomenon these days. Thus the authors tried to develop the porous ceramics with high water retention and evaporation capacity as a maintenance-free material to improve thermal environment. The developed ceramic pellets have high water retention of more than 60% of water absorption and high water evaporation which is similar to water surface. In this study, three types of 5 meter squared large flat-roofed structural specimen simulated reinforced concrete (RC) slab were constructed on the outside. The variation of water content and temperature of the specimens and atmosphere temperature around the specimens were measured from summer in 2009. In the case of the ceramic pellets, the temperature under RC slab was around 15 deg. lower than that of the control. The results were probably contributed by passive cooling effect of evaporated rain water, and the effect was similar to in the case of the grasses. From the viewpoint of thermal environment improvement, substitution of a rooftop gardening by the porous ceramics could be a promising method.

CALCULATION OF FLUENCE-TO-EFFECTIVE DOSE CONVERSION COEFFICIENTS FOR THE OPERATIONAL QUANTITY PROPOSED BY ICRU RC26.

Science.gov (United States)

Endo, Akira

2017-07-01

Fluence-to-effective dose conversion coefficients have been calculated for photons, neutrons, electrons, positrons, protons, muons, pions and helium ions for various incident angles of radiations. The aim of this calculation is to provide a set of conversion coefficients to the Report Committee 26 (RC26) of the International Commission on Radiation Units and Measurements (ICRU) for use in defining personal dose equivalent for individual monitoring. The data sets comprise effective dose conversion coefficients for incident angles of radiations from 0° to ±90° in steps of 15° and at ±180°. Conversion coefficients for rotational, isotropic, superior hemisphere semi-isotropic and inferior hemisphere semi-isotropic irradiations are also included. Numerical data of the conversion coefficients are presented as supplementary data. The conversion coefficients are used to define the personal dose equivalent, which is being considered by the ICRU RC26, as the operational quantity for individual monitoring. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Vapreotide: BMY 41606, RC 160, Sanvar.

Science.gov (United States)

2003-01-01

Vapreotide [Octastatin, Sanvar, RC 160, BMY 41606] is a somatostatin analogue developed at Tulane University School of Medicine, New Orleans, USA, which holds patent rights for vapreotide. Vapreotide provides a much higher metabolic stability than its parent compound. Vapreotide was licensed to Debiopharm for development in Europe. Vapreotide is usually administered SC although a slow-release IM formulation is also available. Other sustained-release formulations are under development. H3 Pharma plans to sign agreements for all indications in the core markets of North America, Europe and in non-core geographic regions during 2003. H3 Pharma will also seek to obtain registration and early market entry in non-core countries with help from partners. Sanvar Immediate Release (IR) has been submitted for approval within the European Union for the treatment of acute oesophageal variceal bleeding (EVB). Sanvar IR has been awarded orphan drug status in the US for EVB. In July 2003, H3 Pharma received written confirmation from the US FDA that the dossier for Sanvar is fileable for registration in the United States for the treatment of esophageal variceal bleeding (EVB). The Sanvar IR (immediate-release) formulation is expected to enter the US market by late 2004. H3 Pharma expects to file for Latin American registration for this indication in the second half of 2003, with registrations in other regions to follow. Sanvar SR has been submitted for Orphan Drug designation.

Seismic Performance of Precast Polystyrene RC Walls

Directory of Open Access Journals (Sweden)

Wibowo Ari

2017-01-01

Full Text Available Precast concrete structure such as precast wall is a concept that is growing rapidly these days. However, the earthquake resistance is believed to be one of its drawbacks. Additionally, the large weight of solid elements also increase the building weight significantly which consequently increase the earthquake base shear force as well. Therefore, investigation on the seismic performance of precast concrete wall has been carried out. Three RC wall specimens using wire mesh reinforcement and EPS (Extended Polystyrene System panel have been tested. This wall was designed as a structural wall that was capable in sustaining lateral loads (in-plane yet were lightweight to reduce the total weight of the building. Parameter observed was the ratio of height to width (aspect ratio of wall of 1.0, 1.5 and 2.0 respectively with the aim to study the behaviour of brittle to ductile transition of the wall. Incremental static load tests were conducted until reaching peak load and then followed by displacement control until failure. Several data were measured at every stage of loading comprising lateral load-displacement behaviour, ultimate strength and collapse mechanism. The outcomes showed that precast concrete walls with a steel wire and EPS panel filler provided considerably good resistance against lateral load.

45 CFR 302.65 - Withholding of unemployment compensation.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Withholding of unemployment compensation. 302.65... HUMAN SERVICES STATE PLAN REQUIREMENTS § 302.65 Withholding of unemployment compensation. The State plan... State agency charged with the administration of the State unemployment compensation laws in accordance...

38 CFR 3.461 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.461 Dependency...'s award of dependency and indemnity compensation will be apportioned where there is a child or...

38 CFR 3.702 - Dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Concurrent Benefits and Elections § 3.702 Dependency and indemnity compensation. (a) Right to elect. A person who is eligible for death...

Detecção da citotoxicidade de materiais biocompatíveis nas linhagens celulares MRC-5, HeLa e RC-IAL MRC-5, HeLa and RC-IAL cell lines sensitivity for detection of cytotoxicity of biocompatible materials

Directory of Open Access Journals (Sweden)

Aurea S. Cruz

1992-04-01

Full Text Available A sensibilidade de uma linhagem celular diplóide e duas heteroplóides, para a detecção de citotoxicidade através do método de difusão em camada de ágar sobre culturas celulares, foi avaliada experimentalmente com solução de ácido ascórbico em diferentes concentrações e, na prática, frente a 562 amostras de 21 diferentes materiais industriais enviados para análise na Seção de Culturas Celulares do Instituto Adolfo Lutz. A linhagem celular heteroplóide designada RC-IAL apresentou, em relação às linhagens MRC-5 e HeLa, maior sensibilidade porque revelou a presença de efeito citotóxico nas menores concentrações utilizadas (10 e 25 ug/ml do ácido ascórbico e apresentou maior diâmetro do halo citotóxico em 15 amostras e igual diâmetro em 16 das 43 amostras (7,6% que resultaram positivas. Nas 43 amostras positivas, a linhagem MRC-5 não revelou citotoxicidade em 3 amostras de espuma e 1 de resina acrílica. O polivinilcloreto (PVC e o polietileno, raramente revelaram positividade, enquanto plástico, algodão e resinas acrílicas revelaram citotoxicidade ao redor de 5%. Em vista dos resultados é discutida a proposta da utilização da linhagem RC-IAL e HeLa para a continuidade das futuras análises solicitadas ao Instituto Adolfo LutzThe sensitivity of diploid and heteroploid cell lines for detection of cytotoxicity using the agar diffusion method on cell culture, was tested with ascorbic acid solution of different concentrations. A total of 562 samples of 21 various materials were tested. The heteroploid cell line, RC-IAL, showed in relation to the MRC-5 and HeLa cell lines, greater sensitivity because it showed the presence of cytotoxic effect with the lowest concentration used (10 and 25ug/ml of ascorbic acid and showed greater diameter of cytotoxic halo in 15 samples and equal diameter in 16 of the 43 positive samples (7.6%. Out of 43 positive samples, the MRC-5 line did not show cytotoxicity in 3 sponge samples and

Free energy analysis of cell spreading.

Science.gov (United States)

McEvoy, Eóin; Deshpande, Vikram S; McGarry, Patrick

2017-10-01

In this study we present a steady-state adaptation of the thermodynamically motivated stress fiber (SF) model of Vigliotti et al. (2015). We implement this steady-state formulation in a non-local finite element setting where we also consider global conservation of the total number of cytoskeletal proteins within the cell, global conservation of the number of binding integrins on the cell membrane, and adhesion limiting ligand density on the substrate surface. We present a number of simulations of cell spreading in which we consider a limited subset of the possible deformed spread-states assumed by the cell in order to examine the hypothesis that free energy minimization drives the process of cell spreading. Simulations suggest that cell spreading can be viewed as a competition between (i) decreasing cytoskeletal free energy due to strain induced assembly of cytoskeletal proteins into contractile SFs, and (ii) increasing elastic free energy due to stretching of the mechanically passive components of the cell. The computed minimum free energy spread area is shown to be lower for a cell on a compliant substrate than on a rigid substrate. Furthermore, a low substrate ligand density is found to limit cell spreading. The predicted dependence of cell spread area on substrate stiffness and ligand density is in agreement with the experiments of Engler et al. (2003). We also simulate the experiments of Théry et al. (2006), whereby initially circular cells deform and adhere to "V-shaped" and "Y-shaped" ligand patches. Analysis of a number of different spread states reveals that deformed configurations with the lowest free energy exhibit a SF distribution that corresponds to experimental observations, i.e. a high concentration of highly aligned SFs occurs along free edges, with lower SF concentrations in the interior of the cell. In summary, the results of this study suggest that cell spreading is driven by free energy minimization based on a competition between decreasing

Do compensation processes impair mental health? A meta-analysis.

Science.gov (United States)

Elbers, Nieke A; Hulst, Liesbeth; Cuijpers, Pim; Akkermans, Arno J; Bruinvels, David J

2013-05-01

Victims who are involved in a compensation processes generally have more health complaints compared to victims who are not involved in a compensation process. Previous research regarding the effect of compensation processes has concentrated on the effect on physical health. This meta-analysis focuses on the effect of compensation processes on mental health. Prospective cohort studies addressing compensation and mental health after traffic accidents, occupational accidents or medical errors were identified using PubMed, EMBASE, PsycInfo, CINAHL, and the Cochrane Library. Relevant studies published between January 1966 and 10 June 2011 were selected for inclusion. Ten studies were included. The first finding was that the compensation group already had higher mental health complaints at baseline compared to the non-compensation group (standardised mean difference (SMD)=-0.38; 95% confidence interval (CI) -0.66 to -0.10; p=.01). The second finding was that mental health between baseline and post measurement improved less in the compensation group compared to the non-compensation group (SMD=-0.35; 95% CI -0.70 to -0.01; p=.05). However, the quality of evidence was limited, mainly because of low quality study design and heterogeneity. Being involved in a compensation process is associated with higher mental health complaints but three-quarters of the difference appeared to be already present at baseline. The findings of this study should be interpreted with caution because of the limited quality of evidence. The difference at baseline may be explained by a selection bias or more anger and blame about the accident in the compensation group. The difference between baseline and follow-up may be explained by secondary gain and secondary victimisation. Future research should involve assessment of exposure to compensation processes, should analyse and correct for baseline differences, and could examine the effect of time, compensation scheme design, and claim settlement on

Forecasting oil price movements with crack spread futures

International Nuclear Information System (INIS)

Murat, Atilim; Tokat, Ekin

2009-01-01

In oil markets, the crack spread refers to the crude-product price relationship. Refiners are major participants in oil markets and they are primarily exposed to the crack spread. In other words, refiner activity is substantially driven by the objective of protecting the crack spread. Moreover, oil consumers are active participants in the oil hedging market and they are frequently exposed to the crack spread. From another perspective, hedge funds are heavily using crack spread to speculate in oil markets. Based on the high volume of crack spread futures trading in oil markets, the question we want to raise is whether the crack spread futures can be a good predictor of oil price movements. We investigated first whether there is a causal relationship between the crack spread futures and the spot oil markets in a vector error correction framework. We found the causal impact of crack spread futures on spot oil market both in the long- and the short-run after April 2003 where we detected a structural break in the model. To examine the forecasting performance, we use the random walk model (RWM) as a benchmark, and we also evaluate the forecasting power of crack spread futures against the crude oil futures. The results showed that (a) both the crack spread futures and the crude oil futures outperformed the RWM; and (b) the crack spread futures are almost as good as the crude oil futures in predicting the movements in spot oil markets. (author)

Multiple Compensation Consultants and CEO Pay

NARCIS (Netherlands)

Kabir, Mohammed Rezaul; Minhat, Marizah

The study examines the practice of employing multiple compensation consultants. Data for a sample of UK companies over the period 2003-2006 are analyzed using a variety of econometric methods. We find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant.

Assessment of Wetland Valuation Processes for Compensation in ...

African Journals Online (AJOL)

The issue of compensation has been debated in various fora; however compensation on wetland resources has not been given the primary place. Wetland valuation like any other type of valuation requires going through stages, which may be more complex than real estate valuation for compensation. This study therefore ...

28 CFR 301.301 - Compensable and noncompensable injuries.

Science.gov (United States)

2010-07-01

... only those injuries suffered during the performance of an inmate's regular work assignment. However... institution, when such work has been approved by staff, may also be compensable. (c) Compensation is not paid... in any activity not related to the actual performance of the work assignment are not compensable, and...

Attitudes toward the dubious compensation claim.

Science.gov (United States)

LEGGO, C

1951-07-01

Laws providing for compensation of workmen for occupational injury are a powerful socio-economic force. In settlement of compensation claims the goal, difficult to achieve, is fairness to employee, employer and insurance carrier. Often, medical, legal, economic and social considerations conflict with one another. A "fact" in one field may not be considered so in another. Since medical data and testimony often guide the ultimate decision of a compensation claim, the physician's attitude is a large factor not only immediately and directly in determination of the case at hand but, perhaps more important, in the ultimate direction of the socio-economic forces which spring from the sum of all such determinations. To perpetuate the good in workmen's compensation laws, the next generation of physicians-and of lawyers and business administrators as well, for they, too, are involved-ought to have basic training in the social sciences in order that they may have a broad rather than a segmental view of the problems with which they deal.

Final Report for SERDP Project RC-1649: Advanced Chemical Measurements of Smoke from DoD-prescribed Burns

Science.gov (United States)

T.J. Johnson; R.J. Yokelson; S.K. Akagi; I.R. Burling; D.R. Weise; S.P. Urbanski; C.E. Stockwell; J. Reardon; E.N. Lincoln; L.T.M. Profeta; A. Mendoza; M.D.W. Schneider; R.L. Sams; S.D. Williams; C.E. Wold; D.W.T. Griffith; M. Cameron; J.B. Gilman; C. Warneke; J.M. Roberts; P. Veres; W.C. Kuster; J de Gouw

2014-01-01

Project RC-1649, "Advanced Chemical Measurement of Smoke from DoD-prescribed Burns" was undertaken to use advanced instrumental techniques to study in detail the particulate and vapor-phase chemical composition of the smoke that results from prescribed fires used as a land management tool on DoD bases, particularly bases in the southeastern U.S. The statement...

CEO Compensation and Disclosure Policy

OpenAIRE

Zhang, Weijia; Zhang, Kun

2016-01-01

This paper examines the relationship between CEO compensation and disclosure policy related to corporate governance information within S&P 500 index. Our sample consists of 456 companies for the period from 2005 to 2015. Most previous researchers mainly put their attention on various corporate governance characteristics such as board size, board independence, and executive ownership when analysing CEO compensation. Our paper extends the previous study by dividing corporate governance into...

12 CFR 918.2 - Annual directors' compensation policy.

Science.gov (United States)

2010-01-01

... § 918.3. At a minimum, such policy shall address the activities or functions for which attendance is... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Annual directors' compensation policy. 918.2... HOME LOAN BANKS BANK DIRECTOR COMPENSATION AND EXPENSES § 918.2 Annual directors' compensation policy...

Gossip spread in social network Models

Science.gov (United States)

Johansson, Tobias

2017-04-01

Gossip almost inevitably arises in real social networks. In this article we investigate the relationship between the number of friends of a person and limits on how far gossip about that person can spread in the network. How far gossip travels in a network depends on two sets of factors: (a) factors determining gossip transmission from one person to the next and (b) factors determining network topology. For a simple model where gossip is spread among people who know the victim it is known that a standard scale-free network model produces a non-monotonic relationship between number of friends and expected relative spread of gossip, a pattern that is also observed in real networks (Lind et al., 2007). Here, we study gossip spread in two social network models (Toivonen et al., 2006; Vázquez, 2003) by exploring the parameter space of both models and fitting them to a real Facebook data set. Both models can produce the non-monotonic relationship of real networks more accurately than a standard scale-free model while also exhibiting more realistic variability in gossip spread. Of the two models, the one given in Vázquez (2003) best captures both the expected values and variability of gossip spread.

Perineural spread in head and neck tumors.

Science.gov (United States)

Brea Álvarez, B; Tuñón Gómez, M

2014-01-01

Perineural spread is the dissemination of some types of head and neck tumors along nervous structures. Perineural spread has negative repercussions on treatment because it requires more extensive resection and larger fields of irradiation. Moreover, perineural spread is associated with increased local recurrence, and it is considered an independent indicator of poor prognosis in the TNM classification for tumor staging. However, perineural spread often goes undetected on imaging studies. In this update, we review the concept of perineural spread, its pathogenesis, and the main pathways and connections among the facial nerves, which are essential to understand this process. Furthermore, we discuss the appropriate techniques for imaging studies, and we describe and illustrate the typical imaging signs that help identify perineural spread on CT and MRI. Finally, we discuss the differential diagnosis with other entities. Copyright © 2013 SERAM. Published by Elsevier Espana. All rights reserved.

Towards Compensation Correctness in Interactive Systems

Science.gov (United States)

Vaz, Cátia; Ferreira, Carla

One fundamental idea of service-oriented computing is that applications should be developed by composing already available services. Due to the long running nature of service interactions, a main challenge in service composition is ensuring correctness of failure recovery. In this paper, we use a process calculus suitable for modelling long running transactions with a recovery mechanism based on compensations. Within this setting, we discuss and formally state correctness criteria for compensable processes compositions, assuming that each process is correct with respect to failure recovery. Under our theory, we formally interpret self-healing compositions, that can detect and recover from failures, as correct compositions of compensable processes.

Report of the working group for nuclear damage compensation system

International Nuclear Information System (INIS)

1989-01-01

The Working Group for Nuclear Damage Compensation System was established within the Atomic Energy Commision of Japan on August 2, 1988. The Group has held five meetings to make a study on the revision of the reserve for nuclear damage compensation. The nuclear damage compensation system in Japan has been established under the Law Concerning Compensation for Nuclear Damages and the Law Concerning Contract for Compensation for Nuclear Damages. The former law requires the nuclear power plant operators to set up a reserve for damage compensation to ensure positive and quick payment of compensation in the event of an accident. The reserve is currently rely on liability insurance and a government compensation contract. The Working Group has concluded that the total reserve should be increased from the current yen10 bill. to yen30 bill. The amount of the reserve specified in the enforcement law for the Law Concerning Compensation for Nuclear Damages should also be increased accordingly. The Law Concerning compensation for Nuclear damage will also be applied to damage which occurs overseas as a result of an accident in Japan. (N.K.)

MTB-USDH Compensation Tracking System (MTB-CTS)

Data.gov (United States)

US Agency for International Development — MTB-USDH Compensation Tracking System: is the USDH Compensation Tracking System (MTB-CTS) to assist managers in monitoring their payroll costs for U.S. direct hires....

Environmental change, phenotypic plasticity, and genetic compensation.

Science.gov (United States)

Grether, Gregory F

2005-10-01

When a species encounters novel environmental conditions, some phenotypic characters may develop differently than in the ancestral environment. Most environmental perturbations of development are likely to reduce fitness, and thus selection would usually be expected to favor genetic changes that restore the ancestral phenotype. I propose the term "genetic compensation" to refer to this form of adaptive evolution. Genetic compensation is a subset of genetic accommodation and the reverse of genetic assimilation. When genetic compensation has occurred along a spatial environmental gradient, the mean trait values of populations in different environments may be more similar in the field than when representatives of the same populations are raised in a common environment (i.e., countergradient variation). If compensation is complete, genetic divergence between populations may be cryptic, that is, not detectable in the field. Here I apply the concept of genetic compensation to three examples involving carotenoid-based sexual coloration and then use these and other examples to discuss the concept in a broader context. I show that genetic compensation may lead to a cryptic form of reproductive isolation between populations evolving in different environments, may explain some puzzling cases in which heritable traits exposed to strong directional selection fail to show the expected evolutionary response, and may complicate efforts to monitor populations for signs of environmental deterioration.

Preloading Effect on Strengthening Efficiency of RC Beams Strengthened with Non- and Pretensioned NSM Strips

Directory of Open Access Journals (Sweden)

Renata Kotynia

2018-02-01

Full Text Available The near surface mounted (NSM technique has been shown to be one of the most promising methods for upgrading reinforced concrete (RC structures. Many tests carried out on RC members strengthened in flexure with NSM fiber-reinforced polymer (FRP systems have demonstrated greater strengthening efficiency than the use of externally-bonded (EB FRP laminates. Strengthening with simultaneous pretensioning of the FRP results in improvements in the serviceability limit state (SLS conditions, including the increased cracking moment and decreased deflections. The objective of the reported experimental program, which consisted of two series of RC beams strengthened in flexure with NSM CFRP strips, was to investigate the influence of a number of parameters on the strengthening efficiency. The test program focused on an analysis of the effects of preloading on the strengthening efficiency which has been investigated very rarely despite being one of the most important parameters to be taken into account in strengthening design. Two preloading levels were considered: the beam self-weight only, which corresponded to stresses on the internal longitudinal reinforcement of 25% and 14% of the yield stress (depending on a steel reinforcement ratio, and the self-weight with the additional superimposed load, corresponding to 60% of the yield strength of the unstrengthened beam and a deflection equal to the allowable deflection at the SLS. The influence of the longitudinal steel reinforcement ratio was also considered in this study. To reflect the variability seen in existing structures, test specimens were varied by using different steel bar diameters. Finally, the impact of the composite reinforcement ratio and the number of pretensioned FRP strips was considered. Specimens were divided into two series based on their strengthening configuration: series “A” were strengthened with one pretensioned and two non-pretensioned carbon FRP (CFRP strips, while series �

Development of Pistachio (Pistacia vera L.) spread.

Science.gov (United States)

Shakerardekani, Ahmad; Karim, Roselina; Ghazali, Hasanah Mohd; Chin, Nyuk Ling

2013-03-01

Pistachio nut (Pistacia vera L.) is one of the most delicious and nutritious nuts in the world. Pistachio spreads were developed using pistachio paste as the main component, icing sugar, soy protein isolate (SPI), and red palm oil (RPO), at different ratios. The highest mean scores of all the sensory attributes were depicted by spreads that were made without addition of SPI. It was found that the work of shear was 0 to 11.0 kg s for an acceptable spread. Sensory spreadability, overall texture, spreadability, and overall acceptability were negatively correlated (R > 0.83) with the work of shear of spreads. The findings indicated that the presence of RPO had a direct effect on the viscoelastic behavior of the pistachio spreads. The a values, which are related to the green color of the pistachio product ranged from 1.7 to 3.9 for spread without addition of RPO, and 4.0 to 5.3 in the presence of RPO. The development of pistachio spread would potentially increase the food uses of pistachio and introduce consumers with a healthier snack food. © 2013 Institute of Food Technologists®

A broadband Soleil-Babinet compensator for ultrashort light pulses

Science.gov (United States)

Xu, Shixiang; Ma, Yingkun; Cai, Yi; Lu, Xiaowei; Zeng, Xuanke; Chen, Hongyi; Li, Jingzhen

2013-12-01

This letter reports a novel design for a broadband Soleil-Babinet compensator including two pairs of optical wedges plus one plate. According to our birefringent dispersion compensation model, we can eliminate the first-order birefringent phase retardation (BPR) dispersion by using three different birefringent crystals. Our results show a Soleil-Babinet compensator based on a MgF2/ADP/KDP combination can work from 0° to 360° phase compensation with the maximal residual BPR less than 6° within the spectral region from 0.65 to 0.95 μm. The residual BPR of the compensator increases monotonically with the spectral deviation from the designed central wavelength, so our compensator is very suitable to be used for broadband laser pulses with most of their energies around the central wavelengths.

34 CFR 75.519 - Dual compensation of staff.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Dual compensation of staff. 75.519 Section 75.519... by a Grantee? Project Staff § 75.519 Dual compensation of staff. A grantee may not use its grantee to pay a project staff member for time or work for which that staff member is compensated from some other...

French academic's views on financial compensation of participants.

Science.gov (United States)

Dualé, Christian; Breysse, Gaétan; Bories-Azeau, Béatrice; Cornu, Catherine

2016-07-01

Whether and how participants in biomedical research should receive financial compensation is debated. We wished to explore how this issue was perceived by French professionals, focusing on different conditions of research. We surveyed referent responders of Clinical Investigation Centres, Research Ethics Committees and hospital administrative departments for clinical research, via referent responders who completed an online questionnaire on behalf of their respective teams. Financial compensation was addressed in terms of general perception, justifications, interpretation of French law, concrete clinical situations and compensation of incurred expenses. Descriptive analyses and correlations were carried out based on scalar responses. The questionnaire was answered by 54/116 (45·6%) centres. The ethical aspects of compensation were viewed differently by Clinical Investigation Centres and Research Ethics Committees, whereas the practical aspects were viewed similarly. Agreement to compensation for patients was lower than for healthy volunteers (74·1 vs. 98·2%). The most frequently cited justifications for compensation apart from the inconveniences of research were the potential risk and the absence of medical benefit. Most of the proposed expenses incurred were to be compensated, but agreement to reimbursement of petrol bills or childcare expense was lower. Although some of the responses align with previous surveys in other countries, this information may help French professionals to harmonise their practices. We also addressed practical issues which could be studied in other European countries, for professionals and participants. Finally, the reluctance to compensate patients requires further study, taking into account welfare environment and consequences for recruitment. © 2016 Stichting European Society for Clinical Investigation Journal Foundation.

An integral modelling approach for the loading and break-up of RC structures due to internal explosion of fragmenting shells

NARCIS (Netherlands)

Weerheijm, J.; Grunwald, C.; Slobbe, A.T.; Ramin, M. von

2017-01-01

The Klotz Group (KG), an international group of experts on explosion safety, investigates the debris throw hazard associated with the accidental detonation of ammunition in reinforced concrete (RC) structures. Experiments are combined with engineering models but also with results of advanced

20 CFR 601.2 - Approval of State unemployment compensation laws.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Approval of State unemployment compensation... unemployment compensation laws. States may at their option submit their unemployment compensation laws for... Employment and Training Administration (ETA), one copy of the State unemployment compensation law properly...

Experiments on non-isothermal spreading

International Nuclear Information System (INIS)

Ehrhard, P.

1992-09-01

Experiments are performed on axisymmetric spreading of viscous drops on glass plates. Two liquids are investigated: silicone oil (M-100) spreads to 'infinity' and paraffin oil spreads to a finite-radius steady state. The experiments with silicone oil partly recover the behaviour of previous workers data; those experiments with paraffin oil provide new data. It is found that gravitational forces dominate at long enough times while at shorter times capillary forces dominate. When the plate is heated or cooled with respect to the ambient gas, thermocapillary forces generate flows that alter the spreading dynamics. Heating (cooling) the plate is found to retard (augment) the streading. Moreover, in case of partial wetting, the finally-approached drop radius is smaller (larger) for a heated (cooled) plate. These data are all new. All these observations are in excellent quantitative agreement with the related model predictions of Ehrhard and Davis (1991). A breakdown of the axisymmetric character of the flow is observed only for very long times and/or very thin liquid layers. (orig.) [de

Predictors of Energy Compensation during Exercise Interventions: A Systematic Review

Directory of Open Access Journals (Sweden)

Marie-Ève Riou

2015-05-01

Full Text Available Weight loss from exercise-induced energy deficits is usually less than expected. The objective of this systematic review was to investigate predictors of energy compensation, which is defined as body energy changes (fat mass and fat-free mass over the total amount of exercise energy expenditure. A search was conducted in multiple databases without date limits. Of 4745 studies found, 61 were included in this systematic review with a total of 928 subjects. The overall mean energy compensation was 18% ± 93%. The analyses indicated that 48% of the variance of energy compensation is explained by the interaction between initial fat mass, age and duration of exercise interventions. Sex, frequency, intensity and dose of exercise energy expenditure were not significant predictors of energy compensation. The fitted model suggested that for a shorter study duration, lower energy compensation was observed in younger individuals with higher initial fat mass (FM. In contrast, higher energy compensation was noted for younger individuals with lower initial FM. From 25 weeks onward, energy compensation was no longer different for these predictors. For studies of longer duration (about 80 weeks, the energy compensation approached 84%. Lower energy compensation occurs with short-term exercise, and a much higher level of energy compensation accompanies long-term exercise interventions.

Software compensation in particle flow reconstruction

Energy Technology Data Exchange (ETDEWEB)

Tran, Huong Lan; Krueger, Katja; Sefkow, Felix [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Green, Steven; Marshall, John; Thomson, Mark [Cavendish Laboratory, Cambridge (United Kingdom); Simon, Frank [Max-Planck-Institut fuer Physik, Muenchen (Germany)

2017-10-15

The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed.

Software compensation in particle flow reconstruction

Energy Technology Data Exchange (ETDEWEB)

Tran, Huong Lan; Krueger, Katja; Sefkow, Felix [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany); Green, Steven; Marshall, John; Thomson, Mark [Cavendish Laboratory, Cambridge (United Kingdom); Simon, Frank [Max-Planck-Institut fuer Physik, Muenchen (Germany)

2017-10-15

The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed. (orig.)

Software compensation in particle flow reconstruction

International Nuclear Information System (INIS)

Tran, Huong Lan; Krueger, Katja; Sefkow, Felix; Green, Steven; Marshall, John; Thomson, Mark; Simon, Frank

2017-10-01

The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed.

A broadband Soleil–Babinet compensator for ultrashort light pulses

International Nuclear Information System (INIS)

Xu, Shixiang; Ma, Yingkun; Cai, Yi; Lu, Xiaowei; Zeng, Xuanke; Chen, Hongyi; Li, Jingzhen

2013-01-01

This letter reports a novel design for a broadband Soleil–Babinet compensator including two pairs of optical wedges plus one plate. According to our birefringent dispersion compensation model, we can eliminate the first-order birefringent phase retardation (BPR) dispersion by using three different birefringent crystals. Our results show a Soleil–Babinet compensator based on a MgF 2 /ADP/KDP combination can work from 0° to 360° phase compensation with the maximal residual BPR less than 6° within the spectral region from 0.65 to 0.95 μm. The residual BPR of the compensator increases monotonically with the spectral deviation from the designed central wavelength, so our compensator is very suitable to be used for broadband laser pulses with most of their energies around the central wavelengths. (letter)

Compensation techniques for non-linearities in H-bridge inverters

Directory of Open Access Journals (Sweden)

Daniel Zammit

2016-12-01

Full Text Available This paper presents compensation techniques for component non-linearities in H-bridge inverters as those used in grid-connected photovoltaic (PV inverters. Novel compensation techniques depending on the switching device current were formulated to compensate for the non-linearities in inverter circuits caused by the voltage drops on the switching devices. Both simulation and experimental results will be presented. Testing was carried out on a PV inverter which was designed and constructed for this research. Very satisfactory results were obtained from all the compensation techniques presented, however the exact compensation method was the most effective, providing the highest reduction in harmonics.

Executive compensation and firm performance: Evidence from Indian firms

Directory of Open Access Journals (Sweden)

Mehul Raithatha

2016-09-01

Full Text Available The study examines the relationship between executive compensation and firm performance among Indian firms. The evidence suggests that firm performance measured by accounting, as well as market-based measures, significantly affects executive compensation. We also test for the presence of persistence in executive compensation by employing the system-generalised methods of moments (GMM estimator. We find significant persistence in executive compensation among the sample firms. Further, we report the absence of pay–performance relationship among the smaller sample firms and business group affiliated firms. Thus, our findings cast doubts over the performance-based executive compensation practices of Indian business group affiliated firms.

Heat transfer and fire spread

Science.gov (United States)

Hal E. Anderson

1969-01-01

Experimental testing of a mathematical model showed that radiant heat transfer accounted for no more than 40% of total heat flux required to maintain rate of spread. A reasonable prediction of spread was possible by assuming a horizontal convective heat transfer coefficient when certain fuel and flame characteristics were known. Fuel particle size had a linear relation...

Energy Spread Sources in TESLA and TTF

International Nuclear Information System (INIS)

Mosnier, A.; Tessier, J.M.

1995-03-01

The beam energy spread in the TESLA linac must be small enough to limit the emittance dilution due to the dispersive effects. This report summarizes the major sources of energy spread both for the TESLA linac and the TTF linac, where these estimations will be carefully checked with beam experiments. The first part recalls the intra-bunch energy spread while the second part looks into the bunch-to-bunch energy spread induced by rf field fluctuations within the bunch train and from pulse-to-pulse. (author). 3 refs., 4 figs

Compensating for the harms of family violence: statutory barriers in Australian victims of crime compensation schemes.

Science.gov (United States)

Forster, Christine

2014-09-01

This article considers the compensative capacity of the victims of crime statutory schemes that are present in all eight Australian jurisdictions for primary victims of family violence. It argues that the recommendations of the Final Report on Family Violence conducted jointly by the Australian Law Reform Commission and the New South Wales Law Reform Commission in 2010, although a positive step, are insufficient to facilitate meaningful compensation to victims of family violence. In addition to the primary limitations identified by the Commissions--a requirement to report the crime to the police within a reasonable time and a requirement for multiple acts of violence to be reduced to a single act if they are related--there are other statutory barriers that disproportionately disadvantage victims of family violence. These include time limitation provisions, a requirement to report the crime to police, the restriction of compensation to prescribed categories of loss which exclude many of the social, vocational, emotional and psychological harms suffered by victims of family violence, and significant cut-backs on the non-economic component of the schemes. This article further argues that the statutory barriers cumulatively contribute to the perception of a crime as an isolated event perpetrated by a deviant individual. The article recommends that specific provisions for family violence victims should be introduced into all schemes including three categories of compensation not tied to criminal offences but rather the different forms of family violence, with a generous compensation range, and no requirement for proof of injury.

Coding-Spreading Tradeoff in CDMA Systems

National Research Council Canada - National Science Library

Bolas, Eduardo

2002-01-01

.... Comparing different combinations of coding and spreading with a traditional DS-CDMA, as defined in the IS-95 standard, allows the criteria to be defined for the best coding-spreading tradeoff in CDMA systems...

Deterministic ripple-spreading model for complex networks.

Science.gov (United States)

Hu, Xiao-Bing; Wang, Ming; Leeson, Mark S; Hines, Evor L; Di Paolo, Ezequiel

2011-04-01

This paper proposes a deterministic complex network model, which is inspired by the natural ripple-spreading phenomenon. The motivations and main advantages of the model are the following: (i) The establishment of many real-world networks is a dynamic process, where it is often observed that the influence of a few local events spreads out through nodes, and then largely determines the final network topology. Obviously, this dynamic process involves many spatial and temporal factors. By simulating the natural ripple-spreading process, this paper reports a very natural way to set up a spatial and temporal model for such complex networks. (ii) Existing relevant network models are all stochastic models, i.e., with a given input, they cannot output a unique topology. Differently, the proposed ripple-spreading model can uniquely determine the final network topology, and at the same time, the stochastic feature of complex networks is captured by randomly initializing ripple-spreading related parameters. (iii) The proposed model can use an easily manageable number of ripple-spreading related parameters to precisely describe a network topology, which is more memory efficient when compared with traditional adjacency matrix or similar memory-expensive data structures. (iv) The ripple-spreading model has a very good potential for both extensions and applications.

Dynamics of Ionic Shifts in Cortical Spreading Depression.

Science.gov (United States)

Enger, Rune; Tang, Wannan; Vindedal, Gry Fluge; Jensen, Vidar; Johannes Helm, P; Sprengel, Rolf; Looger, Loren L; Nagelhus, Erlend A

2015-11-01

Cortical spreading depression is a slowly propagating wave of near-complete depolarization of brain cells followed by temporary suppression of neuronal activity. Accumulating evidence indicates that cortical spreading depression underlies the migraine aura and that similar waves promote tissue damage in stroke, trauma, and hemorrhage. Cortical spreading depression is characterized by neuronal swelling, profound elevation of extracellular potassium and glutamate, multiphasic blood flow changes, and drop in tissue oxygen tension. The slow speed of the cortical spreading depression wave implies that it is mediated by diffusion of a chemical substance, yet the identity of this substance and the pathway it follows are unknown. Intercellular spread between gap junction-coupled neurons or glial cells and interstitial diffusion of K(+) or glutamate have been proposed. Here we use extracellular direct current potential recordings, K(+)-sensitive microelectrodes, and 2-photon imaging with ultrasensitive Ca(2+) and glutamate fluorescent probes to elucidate the spatiotemporal dynamics of ionic shifts associated with the propagation of cortical spreading depression in the visual cortex of adult living mice. Our data argue against intercellular spread of Ca(2+) carrying the cortical spreading depression wavefront and are in favor of interstitial K(+) diffusion, rather than glutamate diffusion, as the leading event in cortical spreading depression. © The Author 2015. Published by Oxford University Press.

Resource Allocation with Adaptive Spread Spectrum OFDM Using 2D Spreading for Power Line Communications

Science.gov (United States)

Baudais, Jean-Yves; Crussière, Matthieu

2007-12-01

Bit-loading techniques based on orthogonal frequency division mutiplexing (OFDM) are frequently used over wireline channels. In the power line context, channel state information can reasonably be obtained at both transmitter and receiver sides, and adaptive loading can advantageously be carried out. In this paper, we propose to apply loading principles to an spread spectrum OFDM (SS-OFDM) waveform which is a multicarrier system using 2D spreading in the time and frequency domains. The presented algorithm handles the subcarriers, spreading codes, bits and energies assignment in order to maximize the data rate and the range of the communication system. The optimization is realized at a target symbol error rate and under spectral mask constraint as usually imposed. The analytical study shows that the merging principle realized by the spreading code improves the rate and the range of the discrete multitone (DMT) system in single and multiuser contexts. Simulations have been run over measured power line communication (PLC) channel responses and highlight that the proposed system is all the more interesting than the received signal-to-noise ratio (SNR) is low.

Spread and Liquidity Issues: A markets comparison

Directory of Open Access Journals (Sweden)

Strašek Sebastjan

2016-03-01

Full Text Available The financial crises are closely connected with spread changes and liquidity issues. After defining and addressing spread considerations, we research in this paper the topic of liquidity issues in times of economic crisis. We analyse the liquidity effects as recorded on spreads of securities from different markets. We stipulate that higher international risk aversion in times of financial crises coincides with widening security spreads. The paper then introduces liquidity as a risk factor into the standard value-at-risk framework, using GARCH methodology. The comparison of results of these models suggests that the size of the tested markets does not have a strong effect on the models. Thus, we find that spread analysis is an appropriate tool for analysing liquidity issues during a financial crisis.

Active Surface Compensation for Large Radio Telescope Antennas

Directory of Open Access Journals (Sweden)

Congsi Wang

2018-01-01

Full Text Available With the development of radio telescope antennas with large apertures, high gain, and wide frequency bands, compensation methods, such as mechanical or electronic compensation, are obviously essential to ensure the electrical performance of antennas that work in complex environments. Since traditional compensation methods can only adjust antenna pointing but not the surface accuracy, which are limited for obtaining high surface precision and aperture efficiency, active surface adjustment has become an indispensable tool in this field. Therefore, the development process of electrical performance compensation methods for radio telescope antennas is introduced. Further, a series of analyses of the five key technologies of active surface adjustment is presented. Then, four typical large antennas that have been designed with active main reflector technology are presented and compared. Finally, future research directions and suggestions for reflector antenna compensation methods based on active surface adjustment are presented.

Adaptive Motion Compensation in Radiotherapy

CERN Document Server

Murphy, Martin J

2011-01-01

External-beam radiotherapy has long been challenged by the simple fact that patients can (and do) move during the delivery of radiation. Recent advances in imaging and beam delivery technologies have made the solution--adapting delivery to natural movement--a practical reality. Adaptive Motion Compensation in Radiotherapy provides the first detailed treatment of online interventional techniques for motion compensation radiotherapy. This authoritative book discusses: Each of the contributing elements of a motion-adaptive system, including target detection and tracking, beam adaptation, and pati

Oral Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14 to reduce Group B Streptococcus colonization in pregnant women: A randomized controlled trial.

Science.gov (United States)

Ho, Ming; Chang, Yin-Yi; Chang, Wei-Chun; Lin, Hung-Chih; Wang, Mei-Hung; Lin, Wu-Chou; Chiu, Tsan-Hung

2016-08-01

This study is to examine the effect of Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14 taken orally before bedtime on Group B Streptococcus (GBS)-positive pregnant women with respect to becoming GBS negative. In total, 110 pregnant women at 35-37 weeks of gestation who were diagnosed by GBS culture as being GBS positive for both vaginal and rectal GBS colonization were randomly assigned to be orally treated with two placebo capsules or two probiotic capsules (containing L. rhamnosus GR-1 and L. reuteri RC-14) before bedtime until delivery. All women were tested for vaginal and rectal GBS colonization again by GBS culture on admission for delivery. Of the 110 participants, 99 completed the study (49 in the probiotic group and 50 in the placebo group). The GBS colonization results changed from positive to negative in 21 women in the probiotic group (42.9%) and in nine women in the placebo group (18.0%) during this period (Chi-square p=0.007). Oral probiotic containing L. rhamnosus GR-1 and L. reuteri RC-14 could reduce the vaginal and rectal GBS colonization rate in pregnant women. Copyright © 2016. Published by Elsevier B.V.

Criteria for emittance compensation in high-brightness photoinjectors

Directory of Open Access Journals (Sweden)

Chun-xi Wang

2007-10-01

Full Text Available A critical process in high-brightness photoinjectors is emittance compensation, which brings under control the correlated transverse emittance growth due to the linear space-charge force. Although emittance compensation has been used and studied for almost two decades, the exact criteria to achieve emittance compensation is not as clear as it should be. In this paper, a perturbative analysis of slice envelopes and emittance evolution close to any reference envelope is developed, via which space-charge and chromatic effects are investigated. A new criterion for emittance compensation is found, which is complementary to the well-known matching condition for the invariant envelope and agrees very well with simulations.

Energy compensation after sprint- and high-intensity interval training.

Directory of Open Access Journals (Sweden)

Matthew M Schubert

Full Text Available Many individuals lose less weight than expected in response to exercise interventions when considering the increased energy expenditure of exercise (ExEE. This is due to energy compensation in response to ExEE, which may include increases in energy intake (EI and decreases in non-exercise physical activity (NEPA. We examined the degree of energy compensation in healthy young men and women in response to interval training.Data were examined from a prior study in which 24 participants (mean age, BMI, & VO2max = 28 yrs, 27.7 kg•m-2, and 32 mL∙kg-1∙min-1 completed either 4 weeks of sprint-interval training or high-intensity interval training. Energy compensation was calculated from changes in body composition (air displacement plethysmography and exercise energy expenditure was calculated from mean heart rate based on the heart rate-VO2 relationship. Differences between high (≥ 100% and low (< 100% levels of energy compensation were assessed. Linear regressions were utilized to determine associations between energy compensation and ΔVO2max, ΔEI, ΔNEPA, and Δresting metabolic rate.Very large individual differences in energy compensation were noted. In comparison to individuals with low levels of compensation, individuals with high levels of energy compensation gained fat mass, lost fat-free mass, and had lower change scores for VO2max and NEPA. Linear regression results indicated that lower levels of energy compensation were associated with increases in ΔVO2max (p < 0.001 and ΔNEPA (p < 0.001.Considerable variation exists in response to short-term, low dose interval training. In agreement with prior work, increases in ΔVO2max and ΔNEPA were associated with lower energy compensation. Future studies should focus on identifying if a dose-response relationship for energy compensation exists in response to interval training, and what underlying mechanisms and participant traits contribute to the large variation between individuals.

Sales compensation governance: the last frontier of corporate reform.

Science.gov (United States)

Gundy, Peter R; Gaeta, Elizabeth C

2004-01-01

The area of sales compensation has remained relatively untouched by recent pressures for compensation reform. This article highlights some of the ways that sales organizations stumble in managing their compensation programs, and why it takes more than a simple tactical fix to address these problems effectively. The authors describe a more structured governance framework that not only identifies and resolves key sales compensation issues, but ultimately safeguards the effectiveness and financial integrity of the sales organization itself.

ENEA TRIGA RC-1 reactor activities in the fields of nuclear medicine and neutron radiography

International Nuclear Information System (INIS)

Chiesa, Gianni; Festinesi, Armando; Palomba, Mario; Rosa, Roberto; Rossi, Gabriela; Sangiovanni, Gino; Santoro, Emilio; Sedda, Antioco Franco; Storelli, Lucio

2008-01-01

In the last three years, TRIGA RC-1 plant staff is involved in collaborations with some roman hospitals for the production of particular radioisotopes for the diagnosis and therapy in the field of human cancer. Further, the thermal column of TRIGA reactor has been prepared for neutron radiography and tomography. For another channel, instruments and equipment above neutron radiography and tomography are in preparation phase. This paper includes an overview of the experimental equipment properly developed by TRIGA staff. (authors)

The structural response and manner of progressive collapse in RC buildings under the blast and Provide approaches to retrofitting columns against blast

Directory of Open Access Journals (Sweden)

GholamReza Havaei

2017-05-01

Full Text Available In accidents caused by explosion, the initial damage is usually caused by direct hit blast that it causes damage and serious destruction of structural components. In this state, the collapse of structural components and the subsequent progressive collapse may cause an increase in damages and eventually collapse of the structure. On the other hand, observations show that most of these buildings designed and built without consideration of their vulnerability to such events. In this study, global and local response of reinforced concrete buildings and their damages evaluated against explosion. First the global stability of building using SAP2000 is evaluated against explosion and then the amount and behaviour of damages in The key structural components of the building after the explosion is investigated using LS DYNA. The study involved four important areas in structural engineering that includes blast load determination, numerical modelling with FEM techniques, material performance under high strain rate and non-linear dynamic analysis. Two types of design methods are recommended for RC columns to provide superior residual capacities. They are RC columns detailing with additional steel reinforcement cages and a composite columns including a central structural steel core. The results showed that the use of this type of columns compared to typical RC column against explosion can have a significant impact in increasing the bearing capacity of structural components against gravity loads after the explosion.

Dynamic Compensation for Two-Axis Robot Wrist Force Sensors

Directory of Open Access Journals (Sweden)

Junqing Ma

2013-01-01

Full Text Available To improve the dynamic characteristic of two-axis force sensors, a dynamic compensation method is proposed. The two-axis force sensor system is assumed to be a first-order system. The operation frequency of the system is expanded by a digital filter with backward difference network. To filter high-frequency noises, a low-pass filter is added after the dynamic compensation network. To avoid overcompensation, parameters of the proposed dynamic compensation method are defined by trial and error. Step response methods are utilized in dynamic calibration experiments. Compared to experiment data without compensation, the response time of the dynamic compensated data is reduced by 30%~40%. Experiments results demonstrate the effectiveness of our method.

Springback Prediction, Compensation and Correlation for Automotive Stamping

International Nuclear Information System (INIS)

Xu Siguang; Zhao Kunmin; Lanker, Terry; Zhang, Jimmy; Wang, C.T.

2005-01-01

To reduce weight and increase fuel efficiency and safety, more and more automotive sheet stamping parts are being made of aluminum and high strength steels. Forming of such materials encounters not just reduced formability but also dimensional quality problems. Springback prediction accuracy and compensation effectiveness have been the major challenge to die development, construction and tryout. In this paper, the factors that affect the accuracy of springback prediction are discussed, which includes the effect of material models, the selection of element size, and the contact algorithms. Springback predictions of several automotive aluminum and high strength panels are compared with measurement data. The examples show that the prediction correlates with measurement data in both springback trend and magnitude. The effect of springback on final product can be reduced or eliminated through process control and die face compensation. The process control method involves finding the root causes of springback and eliminating them through process modification. The geometrical compensation of die surface is a direct way to eliminate the springback effect. The global scaling compensation method is normally limited to parts with relatively small springback. For large springback and twisting, a new approach is discussed, which takes into account of the effect of deformation and springback history. The compensation is achieved iteratively by solving a system of non-linear equations. Production dies were cut to the compensated surface, which shows that the die compensation is an efficient way to reduce springback-induced geometry deviation

Optimal grade control sampling practice in open-pit mining

DEFF Research Database (Denmark)

Engström, Karin; Esbensen, Kim Harry

2017-01-01

Misclassification of ore grades results in lost revenues, and the need for representative sampling procedures in open pit mining is increasingly important in all mining industries. This study evaluated possible improvements in sampling representativity with the use of Reverse Circulation (RC) drill...... sampling compared to manual Blast Hole (BH) sampling in the Leveäniemi open pit mine, northern Sweden. The variographic experiment results showed that sampling variability was lower for RC than for BH sampling. However, the total costs for RC drill sampling are significantly exceeding current costs...... for manual BH sampling, which needs to be compensated for by other benefits to motivate introduction of RC drilling. The main conclusion is that manual BH sampling can be fit-for-purpose in the studied open pit mine. However, with so many mineral commodities and mining methods in use globally...

Video encoder/decoder for encoding/decoding motion compensated images

NARCIS (Netherlands)

1996-01-01

Video encoder and decoder, provided with a motion compensator for motion-compensated video coding or decoding in which a picture is coded or decoded in blocks in alternately horizontal and vertical steps. The motion compensator is provided with addressing means (160) and controlled multiplexers

38 CFR 3.658 - Offsets; dependency and indemnity compensation.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Offsets; dependency and... AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Adjustments and Resumptions § 3.658 Offsets; dependency and indemnity compensation. (a) When an award of dependency and...

Topology dependent epidemic spreading velocity in weighted networks

International Nuclear Information System (INIS)

Duan, Wei; Qiu, Xiaogang; Quax, Rick; Lees, Michael; Sloot, Peter M A

2014-01-01

Many diffusive processes occur on structured networks with weighted links, such as disease spread by airplane transport or information diffusion in social networks or blogs. Understanding the impact of weight-connectivity correlations on epidemic spreading in weighted networks is crucial to support decision-making on disease control and other diffusive processes. However, a real understanding of epidemic spreading velocity in weighted networks is still lacking. Here we conduct a numerical study of the velocity of a Reed–Frost epidemic spreading process in various weighted network topologies as a function of the correlations between edge weights and node degrees. We find that a positive weight-connectivity correlation leads to a faster epidemic spreading compared to an unweighted network. In contrast, we find that both uncorrelated and negatively correlated weight distributions lead to slower spreading processes. In the case of positive weight-connectivity correlations, the acceleration of spreading velocity is weak when the heterogeneity of weight distribution increases. (paper)

FACTORS INFLUENCING YIELD SPREADS OF THE MALAYSIAN BONDS

Directory of Open Access Journals (Sweden)

Norliza Ahmad

2009-01-01

Full Text Available Malaysian bond market is developing rapidly but not much is understood in terms of macroeconomic factors that could influence the yield spread of the Ringgit Malaysian denominated bonds. Based on a multifactor model, this paper examines the impact of four macroeconomic factors namely: Kuala Lumpur Composite Index (KLCI, Industry Production Index (IPI, Consumer Price Index (CPI and interest rates (IR on bond yield spread of the Malaysian Government Securities (MGS and Corporate Bonds (CBs for a period from January 2001 to December 2008. The findings support the expected hypotheses that CPI and IR are the major drivers that influence the changes in MGS yield spreads. However IPI and KLCI have weak and no influence on MGS yield spreads respectively Whilst IR, CPI and IPI have significant influence on the yield spreads of CB1, CB2 and CB3, KLCI has significant influence only on the CB1 yield spread but not on CB2 and CB3 yield spreads.

A network model for Ebola spreading.

Science.gov (United States)

Rizzo, Alessandro; Pedalino, Biagio; Porfiri, Maurizio

2016-04-07

The availability of accurate models for the spreading of infectious diseases has opened a new era in management and containment of epidemics. Models are extensively used to plan for and execute vaccination campaigns, to evaluate the risk of international spreadings and the feasibility of travel bans, and to inform prophylaxis campaigns. Even when no specific therapeutical protocol is available, as for the Ebola Virus Disease (EVD), models of epidemic spreading can provide useful insight to steer interventions in the field and to forecast the trend of the epidemic. Here, we propose a novel mathematical model to describe EVD spreading based on activity driven networks (ADNs). Our approach overcomes the simplifying assumption of homogeneous mixing, which is central to most of the mathematically tractable models of EVD spreading. In our ADN-based model, each individual is not bound to contact every other, and its network of contacts varies in time as a function of an activity potential. Our model contemplates the possibility of non-ideal and time-varying intervention policies, which are critical to accurately describe EVD spreading in afflicted countries. The model is calibrated from field data of the 2014 April-to-December spreading in Liberia. We use the model as a predictive tool, to emulate the dynamics of EVD in Liberia and offer a one-year projection, until December 2015. Our predictions agree with the current vision expressed by professionals in the field, who consider EVD in Liberia at its final stage. The model is also used to perform a what-if analysis to assess the efficacy of timely intervention policies. In particular, we show that an earlier application of the same intervention policy would have greatly reduced the number of EVD cases, the duration of the outbreak, and the infrastructures needed for the implementation of the intervention. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation method for corrosion level of rebar in RC with electrical impedance measurement

Science.gov (United States)

Sasamoto, Akira

2018-04-01

The author reported that the impedance measurement using the 4-terminal method on the RC surface for diagnosing corrosion of internal rebar. The difference between the maximum value at 0.01 Hz and the minimum value around 10 Hz indicates the corrosion level of rebar in that report. This is successive report on a signal processing method for estimating the corrosion level by the measured impedance data to obtain more high accuracy. In the dielectric, a graph of frequency and dielectric constant (Cole-Cole plot diagram by KS Cole and RH Cole article of 1941) draws a shape of circle if the dielectric is independent of frequency but it draws a shape of ellipse in reality due to frequency dependency. Havriliak and Negami have also presented Havriliak-Negami model which introduced parameter into dielectric constant equation which deforms Cole-Cole plot diagram and showed that acquired dielectric data of polymer materials fit to this model with proper parameters. In this report, we first consider electric model connected with resistance and capacitance as a rough model of RC concrete. If the capacitance in this model circuit has some loss of dielectric, it is stated that graph in impedance plot is expected to take as similar deformation in the dielectric Cole-Cole plot. Then a numerical optimization computer code for obtaining parameters in the Cole-Cole plot diagram and Havriliak-Negami model is constructed, and the correlation between the deformation parameter of each model and corrosion is shown by this code. These results are feasibility study for diagnosis of corrosion level of rebar by associated parameters to a shape of impedance graph.

Epidemic spreading in time-varying community networks.

Science.gov (United States)

Ren, Guangming; Wang, Xingyuan

2014-06-01

The spreading processes of many infectious diseases have comparable time scale as the network evolution. Here, we present a simple networks model with time-varying community structure, and investigate susceptible-infected-susceptible epidemic spreading processes in this model. By both theoretic analysis and numerical simulations, we show that the efficiency of epidemic spreading in this model depends intensively on the mobility rate q of the individuals among communities. We also find that there exists a mobility rate threshold qc. The epidemic will survive when q > qc and die when q epidemic spreading in complex networks with community structure.

Post-Tanner spreading of nematic droplets

International Nuclear Information System (INIS)

Mechkov, S; Oshanin, G; Cazabat, A M

2009-01-01

The quasistationary spreading of a circular liquid drop on a solid substrate typically obeys the so-called Tanner law, with the instantaneous base radius R(t) growing with time as R∼t 1/10 -an effect of the dominant role of capillary forces for a small-sized droplet. However, for droplets of nematic liquid crystals, a faster spreading law sets in at long times, so that R∼t α with α significantly larger than the Tanner exponent 1/10. In the framework of the thin film model (or lubrication approximation), we describe this 'acceleration' as a transition to a qualitatively different spreading regime driven by a strong substrate-liquid interaction specific to nematics (antagonistic anchoring at the interfaces). The numerical solution of the thin film equation agrees well with the available experimental data for nematics, even though the non-Newtonian rheology has yet to be taken into account. Thus we complement the theory of spreading with a post-Tanner stage, noting that the spreading process can be expected to cross over from the usual capillarity-dominated stage to a regime where the whole reservoir becomes a diffusive film in the sense of Derjaguin.

Model tests on dynamic performance of RC shear walls

International Nuclear Information System (INIS)

Nagashima, Toshio; Shibata, Akenori; Inoue, Norio; Muroi, Kazuo.

1991-01-01

For the inelastic dynamic response analysis of a reactor building subjected to earthquakes, it is essentially important to properly evaluate its restoring force characteristics under dynamic loading condition and its damping performance. Reinforced concrete shear walls are the main structural members of a reactor building, and dominate its seismic behavior. In order to obtain the basic information on the dynamic restoring force characteristics and damping performance of shear walls, the dynamic test using a large shaking table, static displacement control test and the pseudo-dynamic test on the models of a shear wall were conducted. In the dynamic test, four specimens were tested on a large shaking table. In the static test, four specimens were tested, and in the pseudo-dynamic test, three specimens were tested. These tests are outlined. The results of these tests were compared, placing emphasis on the restoring force characteristics and damping performance of the RC wall models. The strength was higher in the dynamic test models than in the static test models mainly due to the effect of loading rate. (K.I.)

Individual Hearing Loss: Characterization, Modelling, Compensation Strategies

DEFF Research Database (Denmark)

Santurette, Sébastien; Dau, Torsten; Christensen-Dalsgaard, Jakob

2016-01-01

account for such individual differences, which make it challenging to find adequate compensation strategies in hearing devices. How to characterize, model, and compensate for individual hearing loss were the main topics of the fifth International Symposium on Auditory and Audiological Research (ISAAR...

Spreading dynamics in complex networks

International Nuclear Information System (INIS)

Pei, Sen; Makse, Hernán A

2013-01-01

Searching for influential spreaders in complex networks is an issue of great significance for applications across various domains, ranging from epidemic control, innovation diffusion, viral marketing, and social movement to idea propagation. In this paper, we first display some of the most important theoretical models that describe spreading processes, and then discuss the problem of locating both the individual and multiple influential spreaders respectively. Recent approaches in these two topics are presented. For the identification of privileged single spreaders, we summarize several widely used centralities, such as degree, betweenness centrality, PageRank, k-shell, etc. We investigate the empirical diffusion data in a large scale online social community—LiveJournal. With this extensive dataset, we find that various measures can convey very distinct information of nodes. Of all the users in the LiveJournal social network, only a small fraction of them are involved in spreading. For the spreading processes in LiveJournal, while degree can locate nodes participating in information diffusion with higher probability, k-shell is more effective in finding nodes with a large influence. Our results should provide useful information for designing efficient spreading strategies in reality. (paper)

Spreading dynamics in complex networks

Science.gov (United States)

Pei, Sen; Makse, Hernán A.

2013-12-01

Searching for influential spreaders in complex networks is an issue of great significance for applications across various domains, ranging from epidemic control, innovation diffusion, viral marketing, and social movement to idea propagation. In this paper, we first display some of the most important theoretical models that describe spreading processes, and then discuss the problem of locating both the individual and multiple influential spreaders respectively. Recent approaches in these two topics are presented. For the identification of privileged single spreaders, we summarize several widely used centralities, such as degree, betweenness centrality, PageRank, k-shell, etc. We investigate the empirical diffusion data in a large scale online social community—LiveJournal. With this extensive dataset, we find that various measures can convey very distinct information of nodes. Of all the users in the LiveJournal social network, only a small fraction of them are involved in spreading. For the spreading processes in LiveJournal, while degree can locate nodes participating in information diffusion with higher probability, k-shell is more effective in finding nodes with a large influence. Our results should provide useful information for designing efficient spreading strategies in reality.

Nonlinear analysis of r.c. framed buildings retrofitted with elastomeric and friction bearings under near-fault earthquakes

Science.gov (United States)

Mazza, Mirko

2015-12-01

Reinforced concrete (r.c.) framed buildings designed in compliance with inadequate seismic classifications and code provisions present in many cases a high vulnerability and need to be retrofitted. To this end, the insertion of a base isolation system allows a considerable reduction of the seismic loads transmitted to the superstructure. However, strong near-fault ground motions, which are characterised by long-duration horizontal pulses, may amplify the inelastic response of the superstructure and induce a failure of the isolation system. The above considerations point out the importance of checking the effectiveness of different isolation systems for retrofitting a r.c. framed structure. For this purpose, a numerical investigation is carried out with reference to a six-storey r.c. framed building, which, primarily designed (as to be a fixed-base one) in compliance with the previous Italian code (DM96) for a medium-risk seismic zone, has to be retrofitted by insertion of an isolation system at the base for attaining performance levels imposed by the current Italian code (NTC08) in a high-risk seismic zone. Besides the (fixed-base) original structure, three cases of base isolation are studied: elastomeric bearings acting alone (e.g. HDLRBs); in-parallel combination of elastomeric and friction bearings (e.g. high-damping-laminated-rubber bearings, HDLRBs and steel-PTFE sliding bearings, SBs); friction bearings acting alone (e.g. friction pendulum bearings, FPBs). The nonlinear analysis of the fixed-base and base-isolated structures subjected to horizontal components of near-fault ground motions is performed for checking plastic conditions at the potential critical (end) sections of the girders and columns as well as critical conditions of the isolation systems. Unexpected high values of ductility demand are highlighted at the lower floors of all base-isolated structures, while re-centring problems of the base isolation systems under near-fault earthquakes are

An analytical study of the improved nonlinear tolerance of DFT-spread OFDM and its unitary-spread OFDM generalization.

Science.gov (United States)

Shulkind, Gal; Nazarathy, Moshe

2012-11-05

DFT-spread (DFT-S) coherent optical OFDM was numerically and experimentally shown to provide improved nonlinear tolerance over an optically amplified dispersion uncompensated fiber link, relative to both conventional coherent OFDM and single-carrier transmission. Here we provide an analytic model rigorously accounting for this numerical result and precisely predicting the optimal bandwidth per DFT-S sub-band (or equivalently the optimal number of sub-bands per optical channel) required in order to maximize the link non-linear tolerance (NLT). The NLT advantage of DFT-S OFDM is traced to the particular statistical dependency introduced among the OFDM sub-carriers by means of the DFT spreading operation. We further extend DFT-S to a unitary-spread generalized modulation format which includes as special cases the DFT-S scheme as well as a new format which we refer to as wavelet-spread (WAV-S) OFDM, replacing the spreading DFTs by Hadamard matrices which have elements +/-1 hence are multiplier-free. The extra complexity incurred in the spreading operation is almost negligible, however the performance improvement with WAV-S relative to plain OFDM is more modest than that achieved by DFT-S, which remains the preferred format for nonlinear tolerance improvement, outperforming both plain OFDM and single-carrier schemes.

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

Science.gov (United States)

Toprak, A. Emre; Gülay, F. Gülten; Ruge, Peter

2008-07-01

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performed on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 m×7.80 m = 127.90 m2 with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

International Nuclear Information System (INIS)

Toprak, A. Emre; Guelay, F. Guelten; Ruge, Peter

2008-01-01

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performed on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 mx7.80 m = 127.90 m 2 with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher

20 CFR 10.15 - May compensation rights be waived?

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false May compensation rights be waived? 10.15 Section 10.15 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS, DEPARTMENT OF LABOR FEDERAL... AMENDED General Provisions Rights and Penalties § 10.15 May compensation rights be waived? No employer or...

31 CFR 30.0 - Executive compensation and corporate governance.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Executive compensation and corporate governance. 30.0 Section 30.0 Money and Finance: Treasury Office of the Secretary of the Treasury TARP STANDARDS FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.0 Executive compensation and corporate governance...

Critical Issues in Assessing Teacher Compensation. Backgrounder. No. 2638

Science.gov (United States)

Richwine, Jason; Biggs, Andrew G.

2012-01-01

A November 2011 Heritage Foundation report--"Assessing the Compensation of Public-School Teachers"--presented data on teacher salaries and benefits in order to inform debates about teacher compensation reform. The report concluded that public-school teacher compensation is far ahead of what comparable private-sector workers enjoy, and that…

Peace/Williston fish and wildlife compensation program: 1992-1993 public compensation report

International Nuclear Information System (INIS)

Bemister, C.N.

1993-01-01

The Peace/Williston Fish and Wildlife Compensation Program is a joint initiative by British Columbia Hydro and the provincial environment ministry to enhance and protect fish and wildlife resources and their habitat in the Williston watershed affected by the construction of the WAC Bennett and Peace Canyon dams on the Peace River. The interest from a fund of $11 million, established by BC Hydro in 1988, is used to maintain the compensation programs. Public input to the ongoing fish and wildlife programs is provided by a public consultation program. To date, the Peace/Williston compensation program has undertaken 93 projects to either conserve or enhance fish and wildlife through habitat improvement and protection. A summary is presented of the activities undertaken by the public consultation program in 1992/93 and public attitudes toward the consultation program. Activities undertaken in the fish and wildlife enhancement program are summarized in appendices. Fisheries programs included stocking, stream fertilization, small lake surveys, preparation of a side channel in Carbon Creek for multi-species spawning, and creation of an artificial spring at Windy Point for spawning purposes. Wildlife programs included channel clearance and vegetation supply improvements to enhance muskrat and beaver habitat; radio monitoring of sheep and elk; studying the feasibility of transplanting elk herds; and purchase of critical ungulate winter habitat lands. 13 figs., 4 tabs

26 CFR 1.85-1 - Unemployment compensation.

Science.gov (United States)

2010-04-01

.... (a) Introduction. Section 85 prescribes rules relating to the inclusion in gross income of... than in cash or on some other basis. (ii) Disability and worker's compensation payments. Amounts in the nature of unemployment compensation also include cash disability payments made pursuant to a governmental...

75 FR 76079 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-12-07

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

75 FR 53023 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-08-30

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

75 FR 22679 - Sound Incentive Compensation Guidance

Science.gov (United States)

2010-04-29

... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

Synchrony - Cyberknife Respiratory Compensation Technology

International Nuclear Information System (INIS)