Methodology for Evaluating Raw Material Changes to RSRM Elastomeric Insulation Materials

Science.gov (United States)

Mildenhall, Scott D.; McCool, Alex (Technical Monitor)

2001-01-01

The Reusable Solid Rocket Motor (RSRM) uses asbestos and silicon dioxide filled acrylonitrile butadiene rubber (AS-NBR) as the primary internal insulation to protect the case from heat. During the course of the RSRM Program, several changes have been made to the raw materials and processing of the AS-NBR elastomeric insulation material. These changes have been primarily caused by raw materials becoming obsolete. In addition, some process changes have been implemented that were deemed necessary to improve the quality and consistency of the AS-NBR insulation material. Each change has been evaluated using unique test efforts customized to determine the potential impacts of the specific raw material or process change. Following the evaluations, the various raw material and process changes were successfully implemented with no detectable effect on the performance of the AS-NBR insulation. This paper will discuss some of the raw material and process changes evaluated, the methodology used in designing the unique test plans, and the general evaluation results. A summary of the change history of RSRM AS-NBR internal insulation is also presented.

Glucose from a cellulose-containing raw material

Energy Technology Data Exchange (ETDEWEB)

Feniksova, R V

1977-01-01

Glucose was produced by mixing the raw material with an enzyme and water, enzymic hydrolysis of raw material, and separation of the hydrolyzate. To increase the yield of glucose, the hydrolysis took place in 2 stages: at the 1st stage, the hydrolysis was continued until the mixture of glucose and oligosaccharides was obtained under the influence of an active enzyme (1 to 20 units/g of cellulose present in the raw material); at the 2nd stage, cellulase immobilized on an insoluble carrier (by covalent bonds) was used for the hydrolysis of oligosaccharides. The hydromodulus of the suspension of cellulose-containing raw material was maintained 5 to 30. A carrier nonhydrolyzable by cellulase, for instance a homogenious macroporous Aerosil gel, a porous glass, or porous ceramics, was used.

Quality and Sensorial Characteristics of Raw-Vegan Bars

Directory of Open Access Journals (Sweden)

Liana Claudia Salanţă

2015-11-01

Full Text Available Increased consumer interest in healthier food products is driven by a variety of factors including growing awareness of the link between diet and health, the desire to age ‘gracefully’ by maintaining good health, greater convenience in meeting nutritional needs and preventing chronic diseases. In raw food diet, food is consumed predominantly or exclusively as uncooked and unprocessed raw food; the main components of the diet are fruits, nuts, seeds, and sprouted grains and beans. The aim of this study was to obtain two raw-vegan bars using dry raw materials and to establish the physicochemical and sensory characteristics of the products. Raw-vegan bars were formulated using fruits and seeds (cranberries, figs, raisins, raspberries, cashew, chia seeds, etc. and binding agents (honey. Raw-vegan bars stands out among fast foods due to their balanced nutritional content and convenience.  

Strategic raw materials. Risk management; Strategische Rohstoffe. Risikovorsorge

Energy Technology Data Exchange (ETDEWEB)

Bertau, Martin [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Technische Chemie; Gutzmer, Jens [Helmholtz-Institut fuer Ressourcentechnologie Freiberg (Germany); Matschullat, Joerg (ed.) [Technische Univ. Bergakademie Freiberg (Germany). Interdisziplinaeres Oekologisches Zentrum (IOeZ); Kausch, Peter

2014-07-01

This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [German] Dieser Band gliedert sich in vier Kapitel: (1) Rohstoffwirtschaft, (2) Primaere Rohstoffe, (3) Sekundaere Rohstoffe und Recycling,(4). Verarbeitung und Produkte. Die Themen zum Kapitel ''Rohstoffwirtschaft'' sind: Substitution von Rohstoffen - Rahmenbedingungen und Umsetzung; Thales: Strategische Rohstoffe; Zeit fuer

Investigation on pyrolysis of some organic raw materials

Directory of Open Access Journals (Sweden)

Purevsuren B

2017-02-01

Full Text Available We have been working on pyrolysis of some organic raw materials including different rank coals, oil shale, wood waste, animal bone, cedar shell, polypropylene waste, milk casein and characterization of obtained hard residue, tar and pyrolytic water and gas after pyrolysis. The technical characteristics of these organic raw materials have been determined and the thermal stability characteristics such as thermal stability indices (T5% and T25% determined by using thermogravimetric analysis. The pyrolysis experiments were performed at different heating temperatures and the yields of hard residue, tar, pyrolysis water and gaseous products were determined and discussed. The main technical characteristics of hard residue of organic raw materials after pyrolysis have been determined and the adsorption ability of pyrolysis hard residue and its activated carbon of organic raw materials also determined. The pyrolysis tars of organic raw materials were distilled in air condition and determined the yields of obtained light, middle and heavy fractions and bitumen like residue with different boiling temperature. This is the first time to investigate the curing ability of pyrolysis tars of organic raw materials for epoxy resin and the results of these experiments showed that only tar of milk casein has the highest (95.0%, tar of animal bone has certain (18.70% and tars of all other organic raw materials have no curing ability for epoxy resin.

Ethanol is a strategic raw material

Directory of Open Access Journals (Sweden)

Baras Josip K.

2002-01-01

Full Text Available The first part of this review article considers general data about ethanol as an industrial product, its qualities and uses. It is emphasized that, if produced from biomass as a renewable raw material, its perspectives as a chemical raw material and energent are brilliant. Starchy grains, such as corn, must be used as the main raw materials for ethanol production. The production of bioethanol by the enzyme-catalyzed conversion of starch followed by (yeast fermentation, distillation is the process of choice. If used as a motor fuel, anhydrous ethanol can be directly blended with gasoline or converted into an oxygenator such as ETBE. Finally, bioethanol production in Yugoslavia and the possibilities for its further development are discussed.

VERAM - Vision and Roadmap for European Raw Materials

Science.gov (United States)

Baumgarten, Wibke; Vashev, Boris

2017-04-01

The overall objective of VERAM project is to produce a Vision and Roadmap for European Raw Materials in 2050 based on raw materials research and innovation (R&I) coordination. Two leading European Technology Platforms (ETPs): ETP SMR (Sustainable Minerals Resources) and FTP (Forest Technology Platform) are joining forces to develop a common vison and roadmap with the support of ECTP (European Construction Technology Platform), represented by UNIVPM, SusChem (ETP for Sustainable Chemistry), represented by Cefic, EuMaT (Advanced Materials ETP), represented by VITO, ERAMIN 2, represented by Research Centre JUELICH and WoodWisdom Network Plus represented by the Agency for Renewable Resources (FNR). This partnership provides VERAM with expertise from downstream applications and additional knowledge on non-biotic and biotic raw materials. The project encourages capacity building as well as transfer of knowledge. It expects to provide an innovation reference point for the European Institute of Innovation & Technology (EIT) Raw Materials (formerly the KIC Raw MatTERS), to coordinate the network involved in the European Innovation Partnership (EIP) on Raw Materials Commitments and relevant proposals funded under Horizon 2020. It provides a platform for identifying gaps and complementarities and enables their bridging. VERAM will be able to advise the European Commission and Member States on future research needs and policies to stimulate innovation and assist in overcoming fragmentation in the implementing the EIP Raw Materials Strategic Implementation Plan. VERAM looks for mutually beneficial information exchange, encourages cross-fertilization between actions undertaken by different raw material industries, and expects to accelerate exploitation of breakthrough innovations. One of the main outcomes of the project is the presentation of a common long term 2050 Vision and Roadmap for relevant raw materials including metals, industrial minerals and aggregates and wood. The

Toxoplasma gondii infection in workers occupationally exposed to unwashed raw fruits and vegetables: a case control seroprevalence study

Directory of Open Access Journals (Sweden)

Alvarado-Esquivel Cosme

2011-12-01

Full Text Available Abstract Background Through a case control seroprevalence study, we sought to determine the association of Toxoplasma gondii infection with occupational exposure to unwashed raw fruits and vegetables. Methods Subjects, numbering 200, who worked growing or selling fruits and vegetables, and 400 control subjects matched by age, gender, and residence were examined by enzyme immunoassays for the presence of anti-Toxoplasma IgG and IgM antibodies. Socio-demographic, clinical, and behavioral characteristics from the study subjects were obtained. Results Of the 200 fruit and vegetable workers, 15 (7.5% of whom, and 31 (7.8% of the 400 controls were positive for anti-Toxoplasma IgG antibodies (P = 0.96. Anti-Toxoplasma IgM antibodies were found in 2 (1% of the fruit workers and in 11 (2.8% of the control subjects (P = 0.23. Seroprevalence of Toxoplasma antibodies increased with age (P = 0.0004. In addition, seropositivity to Toxoplasma was associated with ill status (P = 0.04, chronic tonsillitis (P = 0.03, and reflex impairment (P = 0.03. Multivariate analysis showed that Toxoplasma infection was associated with consumption of raw meat (OR = 5.77; 95% CI: 1.15-28.79; P = 0.03, unwashed raw fruits (OR = 2.50; 95% CI: 1.11-5.63; P = 0.02, and living in a house with soil floors (OR = 3.10; 95% CI: 1.22-7.88; P = 0.01, whereas Toxoplasma infection was negatively associated with traveling abroad (OR = 0.28; 95% CI: 0.12-0.67; P = 0.005. Conclusions This is the first report of seroprevalence and contributing factors for Toxoplasma infection in workers occupationally exposed to unwashed raw fruits and vegetables, and the results may help in the design of optimal preventive measures against Toxoplasma infection especially in female workers at reproductive age.

Reflections on prospective raw materials and materials with regard to the Czech Republic

International Nuclear Information System (INIS)

Schejbal, C.; Palas, M.

1997-01-01

Reflections on prospective mineral raw materials and materials must rest upon the expected demographic evolution, the evaluation of economic development and the development of manufacturing technologies and materials corresponding to them, trends in the consumption of mineral raw materials and possibilities of securing them. The evaluation of the given factors under conditions of the Czech Republic shows that one of the decisive prerequisites to transforming the Czech economy is to assure the fuel and energy security of the state. In addition to emphasis put on traditional and newly developed technologies of utilization of domestic resources of coal and the development of nuclear power, a diversification of supplies of oil and gas is necessary. Moreover, it is necessary to ensure domestic resources of raw materials to some prospective material areas, or to provide these raw materials by means of imports and/or entrepreneurial activity abroad. As far as raw materials for building and industrial rocks are concerned, it is necessary to support the exploitation and home utilization through laws and suitable economic tools at respecting environmental limitations. With non-traditional prospective raw materials, it will be desirable to promote exploration and mining especially in those cases when a precondition exists for the securing of sufficient reserves or when reserves are already known

Raw material ‘criticality’—sense or nonsense?

International Nuclear Information System (INIS)

Frenzel, M; Kullik, J; Reuter, M A; Gutzmer, J

2017-01-01

The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead. (topical review)

Raw material ‘criticality’—sense or nonsense?

Science.gov (United States)

Frenzel, M.; Kullik, J.; Reuter, M. A.; Gutzmer, J.

2017-03-01

The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead.

Consumption of raw vegetables and fruits: a risk factor for Campylobacter infections.

Science.gov (United States)

Verhoeff-Bakkenes, L; Jansen, H A P M; in 't Veld, P H; Beumer, R R; Zwietering, M H; van Leusden, F M

2011-01-05

The purpose of this study was to determine the prevalence of Campylobacter in fresh vegetables and fruits at retail level in the Netherlands, and to estimate its implications on the importance of vegetables and fruits as risk factor for campylobacteriosis. Thirteen of the 5640 vegetable and fruit samples were Campylobacter positive, resulting in a prevalence of 0.23% (95% confidence interval (Cl): 0.12-0.39%). The prevalence of packaged products (0.36%, 95% Cl: 0.17-0.66) was significantly higher than of unpackaged products (0.07; 95% Cl: 0.01-0.27). No statistical differences were found between seasons. Combining the mean prevalence found in this study with data on the consumption of vegetables and fruits, an exposure of 0.0048 campylobacters ingested per person per day in the Netherlands by transmission via vegetables and fruits, was calculated. This exposure, as input in a Beta-Poisson dose-response model, resulted in an estimated number of 5.3×10⁵ cases of infection with Campylobacter per year for the whole Dutch population. This constitutes the consumption of raw vegetables and fruits, especially when packaged, to be a risk factor for Campylobacter infections. Copyright © 2010 Elsevier B.V. All rights reserved.

PERSPECTIVE NONMETALLIC RAW MATERIALS AND THEIR UTILIZATION

Directory of Open Access Journals (Sweden)

Havelka Jaroslav

1997-10-01

Full Text Available It is the existence of the domestic base of raw materials and stable or growing markets that are a precondition for the prospectiveness industrial minerals. Traditional and non-traditional prospective nonmetal-liferous raw materials can be distinguished. The main trends in new industrial applications of industrial minerals are being stated. In the Czech Republic, the following may be ranked among the traditional prospective nonme-talliferous raw materials: kaoline, refractory clays, ceramic and expandable clays, glass and foundry sands, li-mestones, building stones, gypsum, cast basalt, bentonite, diatomite, feldspars, graphite. Alkali rocks, industrial garnets, flaky mica, wollastonite and yet unmined staurolite, minerals of the sillimanite group and others belong to the non-traditional prospective industrial minerals.

Osmotic dehydration of fruit and berry raw materials in the food industry

OpenAIRE

N. A. Gribova; L. G. Eliseeva

2017-01-01

Osmotic dehydration has recently received more attention as an effective method of preserving fruits and berries. Osmosis is a simple process that facilitates the processing of fruits and berries in order to preserve the original characteristics, namely nutritional value and organoleptic properties: color, aroma and texture. Osmotic dehydration has found wide application in the preservation of food products, as the activity of water in fruits and berries decreases, in some of them up to 90% o...

Uninterrupted heat-treatment of starch raw materials

Energy Technology Data Exchange (ETDEWEB)

Bronshtein, D Z

1958-01-01

A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45 degrees prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk, weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.

Uninterrupted heat-treatment of starch raw materials

Energy Technology Data Exchange (ETDEWEB)

Bronshtein, D Z

1958-01-01

A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45/sup 0/ prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in a plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.

Pellet production from agricultural raw materials - A systems study

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Daniel; Bernesson, Sven; Hansson, Per-Anders [Department of Energy and Technology, Swedish University of Agricultural Sciences, P.O. Box 7032, SE-75007 Uppsala (Sweden)

2011-01-15

The demand for biofuel pellets has increased considerably in recent years, causing shortage of the traditional raw materials sawdust and wood shavings. In this study, the costs and energy requirements for the production of pellets from agricultural raw materials were analysed. The materials studied were Salix, reed canary grass, hemp, straw, screenings, rape-seed meal, rape cake and distiller's waste. Four production scales were analysed, having an annual output of 80,000, 8000, 800 and 80 tonnes of pellets per year. It was concluded that the raw materials of greatest interest were Salix and reed canary grass. They had competitive raw material costs and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelleting factories. Straw had low production costs but can cause serious ash-related problems and should, as also is the case for screenings, be avoided in small-scale burners. Hemp had high raw material costs and is of less commercial interest, while distiller's waste, rape-seed meal and rape cake had higher alternative values when used as protein feed. The scale of production had a crucial influence on production costs. The machinery was used much more efficiently in large-scale plants, resulting in clear cost savings. Small-scale pelleting, both static and mobile, required cheap raw materials, low labour costs and long utilisation times to be profitable. In most cases, briquetting would be more commercially viable. The energy use in manufacturing pellets from air-dried crops was generally no higher than when moist sawdust was used as the raw material. (author)

Identification of Particles in Parenteral Drug Raw Materials.

Science.gov (United States)

Lee, Kathryn; Lankers, Markus; Valet, Oliver

2018-04-18

Particles in drug products are not good and are therefore regulated. These particles can come from the very beginning of the manufacturing process, from the raw materials. To prevent particles, it is important to understand what they are and where they come from so the raw material quality, processing, and shipping can be improved. Thus, it is important to correctly identify particles seen in raw materials. Raw materials need to be of a certain quality with respect to physical and chemical composition, and need to have no contaminants in the form of particles which could contaminate the product or indicate the raw materials are not pure enough to make a good quality product. Particles are often seen when handling raw materials due to color, size, or shape characteristics different from those in the raw materials. Particles may appear to the eye to be very different things than they actually are, so microscope, chemical, and elemental analyses are required for accuracy in proper identification. This paper shows how using three different spectroscopy tools correctly and together can be used to identify particles from extrinsic, intrinsic, and inherent particles. Sources of materials can be humans and the environment (extrinsic), from within the process (intrinsic), and part of the formulation (inherent). Microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and IR spectroscopy are excellent tools for identifying particles because they are fast and accurate techniques needing minimal sample preparation that can provide chemical composition as well as images that can be used for identification. The micro analysis capabilities allow for easy analysis of different portions of samples so multiple components can be identified and sample preparation can be reduced. Using just one of these techniques may not be sufficient to give adequate identification results so that the source of contamination can be adequately identified. The

Development of passion fruit juice beverage

Science.gov (United States)

Zhu, Xiang-hao; Duan, Zhen-hua; Yang, Yu-xia; Huang, Xin-hui; Xu, Cheng-ling; Huang, Zhi-zhuo

2017-12-01

In this experiment, the whole fruit of passion fruit was used as raw material. The effects of the ratio of material to liquid (RML), the amount of sucrose addition and the pH on the quality of passion fruit juice beverage were investigated by single factor test. And the optimum process conditions of passion fruit juice beverage were determined by orthogonal test. The results show that the optimum process paramenters were as follow: RML was 1:3, pH was 4.0 and sucrose addition was 8%. Under such optimal conditions, the color of passion fruit juice beverage was red, the flavor of passion fruit was rich and it tasted pleasant.

Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing

Science.gov (United States)

Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs

2017-04-01

The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.

7 CFR 58.332 - Segregation of raw material.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Segregation of raw material. 58.332 Section 58.332... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Operations and Operating Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...

Raw material supply: challenge and chance for economy and state

Energy Technology Data Exchange (ETDEWEB)

Casper, W

1976-01-01

The imprint left by the 1973 oil embargo makes all nations aware of their dependence upon this and other raw materials. The author says the brunt of the embargo has dealt a heavier blow than has been realized on industrial nations and developing countries alike. The drastic decline of raw material prices has had threatening consequences for a number of raw-material-producing developing countries, making some nations unite for the purpose of market regulation. The cartel-like union of copper-producing countries is cited; producers of bauxite, iron ore, and tungsten have united; and some producers of tin have united. So far, the attempt to apply the oil strategy to other raw materials has not achieved the desired results; however, raw materials are no longer just a phase of the industrial process but have become a political matter of prime importance. (MCW)

Raw materials for aluminium production

International Nuclear Information System (INIS)

Galushkin, N.V.

1995-01-01

This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.

Insulating materials from renewable raw materials. 4. ed.; Daemmstoffe aus nachwachsenden Rohstoffen

Energy Technology Data Exchange (ETDEWEB)

Brandhorst, Joerg; Spritzendorfer, Josef; Gildhorn, Kai; Hemp, Markus

2012-03-27

The thermal insulation has become a central issue in the construction and renovation of buildings. The question of healthy building materials and appropriate construction follows the desire of a comfartable and allergy-free living. Due to these developments, insulation materials from renewable resources increasingly has raised the consciousness. The brochure under consideration describes the dynamic market of insulation materials consisting of renewable raw materials. Wood fibers, wood wool, sheep wool, flax, hemp, reeds, meadow grass, cork, cellulose, seaweed and bulrushes are considered as renewable raw materials for insulating materials.

Plastic raw materials in Neolithic pottery production

Directory of Open Access Journals (Sweden)

Alexander A. Bobrinsky

2012-12-01

Full Text Available The paper is dedicated to the investigation of various natural silts as the most ancient type of raw material used in pottery production. The authors describe the specific features of the composition of plain and mountain silts, and discover the same features in ancient ceramics from different regions in Russia. It can be concluded that silts were the earliest raw material used, a tradition that faded away during the evolution of pottery production.

Radiating sterilization of fruits of the barberry ordinary berberis vulgaris L

International Nuclear Information System (INIS)

Abilova, I.E.

2006-01-01

Full text: The riches of flora of Azerbaijan with its specific saturation represent a huge raw-material base for a farmaceutical industry. In territory of republic 3 kinds of a barberry wildly grow, a perspective kind is the barberry ordinary Berberis vulgaris L.In the medical purposes leaves, a root, stalks and fruits of a barberry are applied. Berries as water tincture are applied at rheumatism, a malaria, a diabetes [I.A.Damirov and etn-tilde 1988; Hofbauer F., Askeril M, 2002, etc.], at diseases of a gastroenteric path, easy, at diseases of a mouth [Ikram M, 1975]. Biochemical processes in the collected raw material during first time proceed, as in an alive plant, that is synthesis of biologi-cally active substances prevails. On a measure natural losing water in connection with the termination of receipt of a moisture and nutrients, processes of an exchange are shifted aside disintegration that results in decrease of biologically active substances in vegetative raw material. However in some cases the processes proceeding in drying raw material result on the contrary, in increase in the maintenance of working substances. Therefore improvement of ways of drying and processing of medicinal raw material by influence of small dozes ? - radiations c the purpose of reception of the high-quality raw material, connected with growing need of a global farmaceutical industry for herbs and phitopreparats is an actual problem. As a result of experimental researches conditions of radiating sterilization of fruits of a barberry ?-radiation are picked up at small dozes and at different values ionizating radiations. Fruits of a barberry were irradiated with ?-radiation on radioisotope installation 60n-tildei-circumflex at values of a doze of an irradiation in limits from 1.0 up to 1.5eGr at duration of an irradiation till 30 minutes. The qualitative control were carried out chromatografic (thin layer chromatography) and spectral (UV-VIS and IR) methods later 6, 12 and 24 months

21 CFR Appendix C to Part 101 - Nutrition Facts for Raw Fruits and Vegetables

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Nutrition Facts for Raw Fruits and Vegetables C Appendix C to Part 101 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION FOOD LABELING Pt. 101, App. C Appendix C to Part 101—Nutrition Facts...

Analytical techniques for characterization of raw materials in cell culture media

Directory of Open Access Journals (Sweden)

Sharma Chandana

2011-11-01

Full Text Available Abstract Raw materials are a critical part of any cell culture medium; therefore, it is of utmost importance to understand and characterize them for high-quality product. The raw material characterization (RMC program at SAFC focuses on individual screening of raw materials both analytically and biologically. The goal of the program is to develop the best-in-class knowledge base of the raw materials used in SAFC’s media formulations and their impact on performance of products.

Occurrence of Intestinal Parasitic Contamination in Select Consumed Local Raw Vegetables and Fruits in Kuantan, Pahang

Science.gov (United States)

Yusof, Afzan Mat; Mohammad, Mardhiah; Abdullahi, Muna Abshir; Mohamed, Zeehaida; Zakaria, Robaiza; Wahab, Ridhwan Abdul

2017-01-01

Intestinal parasitic infections are one of the most common causes of human diseases that result in serious health and economic issues in many developing and developed countries. Raw vegetables and fruits play an important role in transmitting parasites to humans. Hence, the aim of this study was to investigate the parasitological contamination of select commonly consumed local leafy vegetables and fruits in Kuantan, Malaysia. One kilogram of locally consumed raw vegetables and fruits were collected randomly from the Kuantan wet market (Pasar Tani) during the monsoon season (November 2014–January 2015) and the dry season (February 2015–April 2015). A standard wet mount procedure and modified Ziehl-Neelsen staining were used for the detection of parasites. In the present study, the examination of vegetables revealed five different parasite species. The vegetable samples collected from Kuantan’s wet market were positive for both helminthes and protozoa. However, the fruits samples were negative for parasitic contamination. Pegaga was the most contaminated leafy vegetable in this study, and Strongyloides was the parasite found most frequently. Furthermore, there was a high diversity in the type of parasites observed during the dry season compared to the monsoon season. Therefore, further action should be taken to reduce the occurrence of parasitic contamination in vegetables by implementing the principles of good agricultural practice and improving water treatment efficacy. PMID:28228914

Order acceptance in food processing systems with random raw material requirements

NARCIS (Netherlands)

Kilic, Onur A.; van Donk, Dirk Pieter; Wijngaard, Jacob; Tarim, S. Armagan

This study considers a food production system that processes a single perishable raw material into several products having stochastic demands. In order to process an order, the amount of raw material delivery from storage needs to meet the raw material requirement of the order. However, the amount

Determination Of Work Indexes Of Basic Ceramic Raw Materials

OpenAIRE

İPEK, Halil; UÇBAŞ, Yaşar

2017-01-01

In this study, the grindability of basic ceramic raw materials have been investigated by using Bond grindability test and the results have been compared. Bond grindability test results show that work indexes of raw materials are dependent on their hardnesses.

Traceability System Model for Quality Gelatin Raw Material of Cattle Hides

Directory of Open Access Journals (Sweden)

S Nur

2010-09-01

Full Text Available Several criteria must be accomplished within the provision of quality products in terms of the types of materials, the processing methods and effort to get it. Traceability system involves various parties that have different needs and goals in the process of supplying raw materials. Hence, there is a need for institutional systems engineering that can organize and manage the tracking process, the procurement of raw materials that guarantee the origin of gelatin raw materials, and facilitate the industry and customer to create a standardized quality of product. The purpose of the study formulates the institutional tracking models of gelatin raw material from cattle hide based on various criteria and assessment of the expert opinion. The methods used in this study were Interpretative structural modeling to formulate a representation of institutional tracking efficiently and analytical hierarchy process to determine the tracking strategy of industrial gelatin raw materials from cowhide. The results obtained from the study were some key elements of institutional tracking model for industrial gelatin raw materials from cowhide and the traceability strategies for industrial raw materials from cattle hide gelatin Indonesia. (Animal Production 12(3: 190-198 (2010 Key Words: traceability, institutional model, cattle hide, gelatin

Sulfur Release from Cement Raw Materials during Solid Fuel Combustion

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of solid fuels in the material inlet end of cement rotary kilns, local reducing conditions can occur and cause decomposition of sulfates from cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2 concentration, which may cause...... deposit formation in the kiln system. SO2 release from cement raw materials during combustion of solid fuels has been studied experimentally in a high temperature rotary drum. The fuels were tire rubber, pine wood, petcoke, sewage sludge, and polypropylene. The SO2 release from the raw materials...

Refining of raw materials, lignite present economic problems

Energy Technology Data Exchange (ETDEWEB)

Schirmer, G.

1985-06-01

East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.

Raw materials in the manufacture of biotechnology products: regulatory considerations.

Science.gov (United States)

Cordoba-Rodriguez, Ruth

2010-01-01

The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

an assessment of timber trees producing valuable fruits and seeds ...

African Journals Online (AJOL)

User

It is observed that most of the timber trees producing valuable fruits and seeds have low ... sector of the economy by providing major raw materials (saw logs, ... the trees also produce industrial raw materials like latex, ... villagers while avoiding some of the ecological costs of ..... enzymes of rats with carbon tetrachloride.

Renewable raw materials in the field of industry; Nachwachsende Rohstoffe in der Industrie

Energy Technology Data Exchange (ETDEWEB)

Peters, D.

2006-07-01

Being used to the practiced processing of raw materials for many decades the industry had to tap the advantage of renewable raw materials again. Conventional processing methods had to be changed and to be newly developed. This has been a rewarding task considering the ecological advantages but also considering the interesting markets for products based upon renewable raw materials. Today the German industry above all the chemical industry again processes agricultural and forestal raw materials to a considerable extent. Ten percent of the raw materials processed by the chemical industry are renewable. The wood processing industry is an important economic sector that achieves a value creation with the raw material wood exceeding the value creation of other industries by far. This brochure gives an overview of the possible substances, which are processed from renewable raw materials in Germany and it shows the important role that agricultural raw materials and wood already play for the industry nowadays. (orig.)

Moringa fruit inhibits LPS-induced NO/iNOS expression through suppressing the NF-κ B activation in RAW264.7 cells.

Science.gov (United States)

Lee, Hyo-Jin; Jeong, Yun-Jeong; Lee, Tae-Sung; Park, Yoon-Yub; Chae, Whi-Gun; Chung, Il-Kyung; Chang, Hyeun-Wook; Kim, Cheorl-Ho; Choi, Yung-Hyun; Kim, Wun-Jae; Moon, Sung-Kwon; Chang, Young-Chae

2013-01-01

In this study, we evaluated the anti-inflammatory effects of moringa (Moringa oleifera Lam.), a natural biologically active substance, by determining its inhibitory effects on pro-inflammatory mediators in lipopolysaccharide (LPS)-stimulated macrophage RAW264.7 cells. Extracts from different parts of moringa (root, leaf, and fruit) reduced LPS-induced nitric oxide (NO) release in a dose-dependent manner. The moringa fruit extract most effectively inhibited LPS-induced NO production and levels of inducible nitric oxide synthase (iNOS). The moringa fruit extract also was shown to suppress the production of inflammatory cytokines including IL-1β, TNF-α, and IL-6. Furthermore, moringa fruit extract inhibited the cytoplasmic degradation of I κ B -α and the nuclear translocation of p65 proteins, resulting in lower levels of NF -κ B transactivation. Collectively, the results of this study demonstrate that moringa fruit extract reduces the levels of pro-inflammatory mediators including NO , IL-1β, TNF-α, and IL-6 via the inhibition of NF -κ B activation in RAW264.7 cells. These findings reveal, in part, the molecular basis underlying the anti-inflammatory properties of moringa fruit extract.

Raw material studies of West Central Serbia

Directory of Open Access Journals (Sweden)

Vera Bogosavljević Petrović

2014-03-01

Full Text Available This paper deals with raw material problems in the territory of West Central Serbia geologically determined as the Čačak-Kraljevo (or West Morava basin. Our research is presented through the most striking case studies, Lojanik, Vlaška Glava and Lazac.  The Lojanik hill is a silicified forest by origin. It has occasionally been in use from the earliest periods of prehistory until today as a source of black and ochre-coloured flint, opal and silicified wood. A detailed prospection, including the mapping of surface finds using square nets, was conducted during two research campaigns.The Vlaška Glava is an open-air Palaeolithic site at which artefacts made of white, ochre, red, brown and black chert, silicified magnesite, volcanic and metamorphic rocks were found. Our research of primary and secondary geological deposits in the vicinity of the site showed equivalent raw material. We also found an interesting primary deposit of high quality bluish grey flint with outcrop activities (Workshop 1.The Lazac shaft is a contemporary magnesite mine, recently abandoned because of the high percentage of silicon-dioxide. We determined the same raw material in collections found at nearby Neolithic sites. Certain similarities between the wooden support systems of ore exploration in the Middle Ages and modern times were established at the entrance of the shaft.Our research in the territory of the West Morava basin resulted in reconstruction of some links between geological deposits and settlements and also creation of a relevant base for future raw material studies.

Insulating materials from renewable raw materials. 3. upd. ed.; Daemmstoffe aus nachwachsenden Rohstoffen

Energy Technology Data Exchange (ETDEWEB)

Brandhorst, Joerg; Spritzendorfer, Josef; Gildhorn, Kai; Hemp, Markus

2009-07-01

Due to increasing energy prices, obligations to climatic protection and the desire for comfortable, allergy-free living, the thermal insulation is a central question with building and sanitation. Under this aspect, the contribution under consideration describes the very dynamic market of the insulating materials from renewable raw materials and deals with the questions of the users. In particular, the following raw materials are considered in the production of insulating materials: Wood fibre, wood chips, wood wool, sheep wool, flax, hemp, reeds, straw, cellulose.

PROCESS FOR THE PREPARATION OF JUICE FROM FRUIT RAW MATERIAL AND MEDALS

Directory of Open Access Journals (Sweden)

Andrey Aleksandrovich Belyaev

2017-01-01

Full Text Available The article presents the results of technology development and the formulation of a fruit juice with honey, the study of the organoleptic, physical-chemical and microbiological properties of the resulting product. The best organoleptic properties are set for a sample containing small-fruited apple juice – 750 ml, honey – 25 ml, syrup hips – 50 ml, water – 175 ml. The results of the physicochemical tests showed that the content of soluble solids in the juice was 16.2% sugar – 37.6% titratable acids in terms of malic acid – 0.46%. Mesophilic clostridium, spore-forming mesophilic aerobic and facultative anaerobic microorganisms group asporogenous microorganisms, mold fungi, yeast in samples of blended juice is not detected. Inclusion in separate heat treatment technology for honey syrup – 60 degrees, and small-fruited apple juice – 75 degrees is necessary for the greatest saving in honey nutrients, and the receipt of the application of microbiological safety performance. In terms of industrial sterility of the sample corresponds to the technical regulations on juice products TR CU 023/2011.

Tracing and control of raw materials sourcing for vaccine manufacturers.

Science.gov (United States)

Faretra Peysson, Laurence

2010-05-01

The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

Influence of man-made aluminosilicate raw materials on physical and mechanical properties of building materials.

Science.gov (United States)

Volodchenko, A. A.; Lesovik, V. S.; Stoletov, A. A.; Glagolev, E. S.; Volodchenko, A. N.; Magomedov, Z. G.

2018-03-01

It has been identified that man-made aluminosilicate raw materials represented by clay rock of varied genesis can be used as energy-efficient raw materials to obtain efficient highly-hollow non-autoclaved silicate materials. A technique of structure formation in the conditions of pressureless steam treatment has been offered. Cementing compounds of non- autoclaved silicate materials based on man-made aluminosilicate raw materials possess hydraulic properties that are conditioned by the process of further formation and recrystallization of calcium silicate hydrates, which optimizes the ratio between gellike and crystalline components and densifies the cementing compound structure, which leads to improvement of performance characteristics. Increasing the performance characteristics of the obtained products is possible by changing the molding conditions. For this reason, in order to create high-density material packaging and, as a result, to increase the strength properties of the products, it is reasonable to use higher pressure, under which raw brick is formed, which will facilitate the increase of quality of highly-hollow products.

Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials

Science.gov (United States)

Pękala, Agnieszka

2017-10-01

Thorium and uranium are constant components of all soils and most minerals thereby rock raw materials. They belong to the particularly dangerous elements because of their natural radioactivity. Evaluation of the content of the radioactive elements in the rock raw materials seems to be necessary in the early stage of the raw material evaluation. The rock formations operated from deposits often are accumulated in landfills and slag heaps where the concentration of the radioactive elements can be many times higher than under natural conditions. In addition, this phenomenon may refer to buildings where rock raw materials are often the main components of the construction materials. The global control system of construction products draws particular attention to the elimination of used construction products containing excessive quantities of the natural radioactive elements. In the presented study were determined the content of thorium and uranium in rock raw materials coming from the Bełachatów lignite deposit. The Bełchatów lignite deposit extracts mainly lignite and secondary numerous accompanying minerals with the raw material importance. In the course of the field works within the framework of the carried out work has been tested 92 samples of rocks of varied petrographic composition. There were carried out analyses of the content of the radioactive elements for 50 samples of limestone of the Jurassic age, 18 samples of kaolinite clays, and 24 samples of siliceous raw materials, represented by opoka-rocks, diatomites, gaizes and clastic rocks. The measurement of content of the natural radioactive elements thorium and uranium based on measuring the frequency counts of gamma quantum, recorded separately in measuring channels. At the same time performed measurements on volume patterns radioactive: thorium and uranium. The studies were carried out in Mazar spectrometer on the powdered material. Standardly performed ten measuring cycles, after which were calculated

Extrusion Processing of Raw Food Materials and by-products: A Review.

Science.gov (United States)

Offiah, Vivian; Kontogiorgos, Vassilis; Falade, Kolawole O

2018-05-22

Extrusion technology has rapidly transformed the food industry with its numerous advantages over other processing methods. It offers a platform for processing different products from various food groups by modifying minor or major ingredients and processing conditions. Although cereals occupy a large portion of the extruded foods market, several other types of raw materials have been used. Extrusion processing of various food groups, including cereals and pseudo cereals, roots and tubers, pulses and oilseeds, fruits and vegetables, and animal products, as well as structural and nutritional changes in these food matrices are reviewed. Value addition by extrusion to food processing wastes and by-products from fruits and vegetables, dairy, meat and seafood, cereals and residues from starch, syrup and alcohol production, and oilseed processing are also discussed. Extrusion presents an economical technology for incorporating food processing residues and by-products back into the food stream. In contemporary scenarios, rising demand for extruded products with functional ingredients, attributed to evolving lifestyles and preferences, have led to innovations in the form, texture, color and content of extruded products. Information presented in this review would be of importance to processors and researchers as they seek to enhance nutritional quality and delivery of extruded products.

ICE CREAM WITH A COMBINED COMPOSITION OF RAW MATERIALS

Directory of Open Access Journals (Sweden)

O. E. Khodyreva

2013-01-01

Full Text Available Dairy products are the product of daily demand. Nowadays actively assimilate new types of raw materials, tech-nology, formulation. One of the propagation methods of enriching dairy products is a combination of milk and vegetable raw materials. The possibility of making a concentrated paste of Jerusalem artichoke in dairy products was investigated. The ice cream sundae "Vanilla" was chosen as the object of research.

Regenerative raw materials - High technology without end; Nachwachsende Rohstoffe - Spitzentechnologie ohne Ende

Energy Technology Data Exchange (ETDEWEB)

Wenig, Barbara

2007-07-01

Regenerative raw materials are the basis for a multiplicity of environmentally friendly products. Regenerating raw materials fascinate by special qualities and offer the possibility of preserving only restricted existing fossil resources and climatic friendly managing. The review under consideration reports on areas in which vegetable raw materials already are established as well as on future prospects.

Topical papers on raw materials

International Nuclear Information System (INIS)

1978-01-01

In the papers of this working group, the availability of uranium and the long-term supply situation for this raw material are discussed. A problem closely connected with uranium supply are the commercial contracts and their particularities. The points of view of the reporting countries of Great Britain, South Africa, Switzerland, Australia, Japan, and Korea are made clear

Mesta/Kenaf as raw material for Kraft pulping

Energy Technology Data Exchange (ETDEWEB)

Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

1980-03-15

In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

Synthesis of material microporous using raw materials alternative as a source of silica and alumina

International Nuclear Information System (INIS)

Santos, E.A.; Silva, T.L.

2014-01-01

Synthetic zeolites have important properties of a technological viewpoint. Thus, this work aims at the use of natural raw materials such as kaolin waste and wood ash in order to produce these microporous materials. The starting materials were characterized by X-ray diffraction (XRD) and spectroscopy, X-ray fluorescence (XRF); the phases formed as synthesis products were identified by XRD and gravimetric and differential thermal analysis (DTA/TG). Hydrothermal synthesis took place by mixing the raw materials in stoichiometrically calculated batches with NaOH (3M) at 90 °C and time of 6, 20, 24 and 48 hours. The results show the formation of phases of type zeolite A and sodalite, demonstrating the raw materials be an efficient and low cost alternative to producing microporous materials. (author)

Incentivizing secondary raw material markets for sustainable waste management.

Science.gov (United States)

Schreck, Maximilian; Wagner, Jeffrey

2017-09-01

Notwithstanding several policy initiatives in many countries over a number of years, there remains a general sense that too much municipal solid waste is generated and that too much of the waste that is generated is landfilled. There is an emerging consensus that a sustainable approach to waste management requires further development of secondary raw material markets. The purpose of this paper is to propose a theoretical economic model that focuses upon this stage of a sustainable waste management program and explores policy options that could motivate efficiency in secondary raw material markets. In particular, we show how firm profit and social welfare optimizing objectives can be reconciled in a two-product market of waste management processes: landfilling and material reclamation. Our results provide theoretical support for building out recent Circular Economy initiatives as well as for the relatively recent emergence of landfill mining as a means for procuring secondary raw materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of effectiveness of raw materials and materials use in a blast furnace department of a steelworks

Directory of Open Access Journals (Sweden)

E. Kardas

2017-01-01

Full Text Available The paper analyses the quality of raw materials used in the production of blast furnace pig iron. The ferruginous sinter and pellets are the basic raw materials used in the process. The paper presents the impact of those raw materials quality on the effectiveness of the blast furnace process. The process effectiveness will be specified by means of selected process parameters.

Basic Thermal Parameters of Selected Foods and Food Raw Materials

OpenAIRE

Monika Božiková; Ľubomír Híreš; Michal Valach; Martin Malínek; Jan Mareček

2017-01-01

In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of ...

Theoretical backgrounds of non-tempered materials production based on new raw materials

Science.gov (United States)

Lesovik, V. S.; Volodchenko, A. A.; Glagolev, E. S.; Chernysheva, N. V.; Lashina, I. V.; Feduk, R. S.

2018-03-01

One of the trends in construction material science is development and implementation of highly effective finish materials which improve architectural exterior of cities. Silicate materials widely-used in the construction today have rather low decorative properties. Different coloring agents are used in order to produce competitive materials, but due to the peculiarities of the production, process very strict specifications are applied to them. The use of industrial wastes or variety of rock materials as coloring agents is of great interest nowadays. The article shows that clay rock can be used as raw material in production of finish materials of non-autoclaved solidification. This raw material due to its material composition actively interacts with cementing component in steam treatment at 90–95 °C with formation of cementing joints that form a firm coagulative-cristalized and crystallization structure of material providing high physic-mechanical properties of silicate goods. It is determined that energy-saving, colored finish materials with compression strength up to 16 MPa can be produced from clay rocks.

Annual report 2005 General Direction of the Energy and raw materials

International Nuclear Information System (INIS)

2005-01-01

This 2005 annual report of the DGEMP (General Direction of the Energy and the raw Materials), takes stock on the energy bill and accounting of the France. The first part presents the electric power, natural gas and raw materials market in France. The second part is devoted to the diversification of the energy resources with a special attention to the renewable energies and the nuclear energy. The third part discusses the energy and raw materials prices and the last part presents the international cooperation in the energy domain. (A.L.B.)

Natural gas as raw material for industrial development

International Nuclear Information System (INIS)

Kvisle, Steinar

2006-01-01

Industrial development based on natural gas has broad, industrial implications. Norway has a vital industry based on natural gas as raw material, here under Ormen Lange, Snoehvit LNG, Tjeldbergodden and Petrochemical Grenland. The petrochemical industry has challenges, e.g. the cost of raw materials and energy, localization related to the markets, and recruitment, but considerable investments are made in the sector. The Northern areas in Norway may have special challenges related to bringing the product to the market. Solutions to this challenge are in LNG (liquid natural gas), GTL (gas to liquids), and GTO (gas to olefins)

System simulation application for determining the size of daily raw material purchases at PT XY

Science.gov (United States)

Napitupulu, H. L.

2018-02-01

Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.

Material Classification Using Raw Time-of-Flight Measurements

KAUST Repository

Su, Shuochen; Heide, Felix; Swanson, Robin J.; Klein, Jonathan; Callenberg, Clara; Hullin, Matthias; Heidrich, Wolfgang

2016-01-01

We propose a material classification method using raw time-of-flight (ToF) measurements. ToF cameras capture the correlation between a reference signal and the temporal response of material to incident illumination. Such measurements encode unique

Raw material uranium; Rohstoff Uran

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-03-15

Uranium is an important raw material in human life. Mostly using nuclear fission uranium is used in nuclear medicine, industry and research. The most important application is the generation of electricity in nuclear power plants. Due to the global availability the worldwide uranium supply is guaranties for a long time. The contribution covers the issues medicine, neutron research, energy generation, occurrence, mining, processing, recycling and disposal.

1996 Activities report on energies and raw materials

International Nuclear Information System (INIS)

1996-01-01

The 1996 activity survey of the French General Directory for Energy and Raw Materials, which main objectives are to preserve the competitiveness of French economy, enhance environmental protection, secure the long term supply safety and maintain the public service basis for energy supply, is presented. The main themes of the survey are: the nuclear safety in Eastern Europe, the electric power inland market, the evolution of the oil market in 1996, the situation of refining in France, restructuring the BRGM (Mining and Geological Research Bureau), followed by brief facts concerning the sustainable energy development, nuclear energy, electric power, electricity and gas common issues, gas, coal, petroleum products, raw materials and underground materials. A series of global diagrams concludes the survey

Chances for a long-term securing of the raw material supply to the FRG. Pt. 1

International Nuclear Information System (INIS)

1975-09-01

The Federal Republic of Germany is almost completely dependent on raw material imports. Growing raw material consumption and an imminent increase in supply uncertainties will require intensified research and development work in the field of raw material safeguarding. Initial approaches to possible technical solutions are being indicated in connection with four raw materials (aluminium, copper, phosphate and carbon carriers). The material balances of these raw materials are shown and the technical and economic interrelations illustrated in the light of world-wide trends. It is being demonstrated that two essential objectives are to be pursued for securing raw material supplies: 1) extension of the raw material basis for primary and secondary raw materials, 2) improvement of raw material utilization in all sectors of economy. To provide a solution for the wide spectrum of tasks it will be necessary to establish adequate analytical methods and procedures. (orig.) [de

Raw materials for reflector graphite (for reactors)

International Nuclear Information System (INIS)

Wilhelmi, G.; Mindermann, D.

1992-01-01

The manufacturing concept for the core components of German high temperature reactor (HTR) types of graphite was previously entirely directed to the use of German tar coke (St coke). As the plants for producing this material no longer complied technically with the current environmental protection requirements, one had to assume that they would soon be shut down. To prevent bottlenecks in the erection of future HTR plants, alternative cokes produced by modern processes by Japanese manufacturers were checked for their suitability for the manufacture of reactor graphite. This report describes the investigations carried out on these materials from the safe delayed coking process. The project work, apart from analysis of the main data of the candidate coke considered, included the processing of the raw materials into directly and secondarily extruded graphite rods on the laboratory scale, including characterisation. As the results show, the material data achieved with the previous raw material can be reproduced with Japanese St coke. The tar coke LPC-A from the Nippon Steel Chemical Co., Ltd was decided on as the new standard coke for manufacturing reflector graphite. (orig.) With 15 tabs., 2 figs [de

Map of critical raw material deposits in Europe

Science.gov (United States)

Guillaume, Bertrand

2016-04-01

Map of critical raw material deposits in Europe Guillaume BERTRAND1, Daniel CASSARD1, Nikolaos ARVANITIDIS2, Gerry STANLEY3 and the EuroGeoSurvey Mineral Resources Expert Group4. 1 - Bureau de Recherches Géologiques et Minières (BRGM), Georesources Divison, 3 avenue Claude Guillemin, 45060 Orléans cedex 2, FRANCE. 2 - Sveriges Geologiska Undersökning (SGU), Box 670, SE-751 28, Uppsala, SWEDEN 3 - Geological Survey of Ireland (GSI), Beggars Bush, Haddington Road, Dublin D04 K7X4, IRELAND 4 - EuroGeoSurveys, Rue Joseph II 36-38, 1000 Brussels, BELGIUM The Critical Raw Material (CRM) Deposit Map of Europe, prepared by EuroGeoSurvey's Mineral Resources Expert Group (MREG), shows European mineral deposits from the ProMine Mineral Deposit database containing critical commodities, according to the 2014 list of critical raw materials of the European Commission. EuroGeoSurveys (EGS), The Geological Surveys of Europe, is a not-for-profit organization representing 37 National Geological Surveys and some regional Geological Surveys in Europe. It provides the European Institutions with expert, independent, balanced and practical pan-European advice and information as an aid to problem-solving, policy development, regulatory and programme formulation in areas such as natural resources, energy and geo-hazards. The EGS MREG is actively involved in contributing to policy and strategy-making processes aimed at identifying, characterizing and safeguarding resource potential, especially for critical raw materials through data provision, research, technological development and innovation. The European Union aspires to reducing the import dependency of raw materials, especially CRM, that are essential to Europe's industries. In this respect, mineral resource information, data sharing and networking by European Geological Surveys is crucial. The Strategic Implementation Plan of the European Innovation Partnership on Raw Materials highlights the need for establishing and maintaining a

MICROBIOLOGY OF RAW MATERIALS USED FOR CONFECTIONARY PRODUCTION

Directory of Open Access Journals (Sweden)

Jana Petrová

2015-02-01

Full Text Available The aim of our study was to evaluate the microbiological quality of raw materials used for preparation of confectionery products. For microbiological evaluation total count of bacteria, mesophilic aerobic bacteria, coliform bacteria, yeast and microscopic filamentous fungi in samples of raw materials used in the manufacture and creams of confectionery products were detected. In addition to these groups of microorganisms the presence of pathogenic microorganisms Salmonella spp. and Staphylococcus aureus in creams was monitored. Products are assessed according to the limit values of the number of microorganisms defined in the Codex Alimentary of the Slovak Republic. For microbiological analysis of confectionery products, sampling of components of confectionary products and cream was carried out according to current health regulations and altogether 65 samples of components and creams were collected: 10 samples of raw materials sugar, 10 samples of flour, 10 samples of butter and 10 samples of eggs, 5 samples of butter yolk from cream-filled disposable bag without rum addition, 5 samples of butter yolk from cream-filled disposable bag with rum addition, 5 samples of cream-filled multiple use paid bag, 5 samples of cream-filled newly purchased paid bag, 5 samples of Venček corpus and 5 samples of the French cubes corpus. From raw material the highest TBC (2.65log CFU was in flour, but the lowest in sugar (1.35 log CFU, the highest years counts was found on flour (2.42, but lowest in butter (1.18, while wasn’t in egg. In samples of creams and corpus were increased occurrence of yeast, coliform bacteria. Salmonella spp. and Staphylococcus aureus weren’t isolated from any tested sample.

Annual report 1997. Energies and raw materials

International Nuclear Information System (INIS)

1997-01-01

This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

Improving the Technology of Obtaining Technical Ethanol from Alternative Raw Materials

Directory of Open Access Journals (Sweden)

Sergіj Petrov

2018-05-01

Full Text Available The purpose of the article is to study the properties of fallen leaves as raw materials for the production of bioethanol; Improvement of the technology of recycling cellulosic raw materials into bioethanol in the most energy-efficient and ecological way. As a result of the study, it has been found out that the production of biofuels from renewable raw materials is characterized by features of innovative technology: the rapid growth of this sector of economy is accompanied by a significant increase in market share. The use of fallen leaves as raw material will eliminate the current conflict of interests associated with the use of food raw materials for the production of bioethanol, will prevent the withdrawal of resources from the sphere of food production. Significant positive factors in the production and use of biofuels are improvement of environmental conditions, reduction of the harmful effects of exhaust gases on the human body, reducing environmental pollution and, consequently, reducing morbidity and associated costs of medical care. The use of bioethanol as an ecobiopilot makes it possible to increase the octane number of fuel, and, accordingly, increase the efficiency of the engine. Thus, the use of bioethanol leads to a qualitative improvement of technical and economic indicators, which is also an indicator of innovation. The threat of reducing (exhausting non-renewable sources of energy is also the factor that necessitates the development and improvement of biofuel production technology. The relatively low profitability of biofuel production is due to the low yield of the target product and the high cost of pre-treatment of cellulose raw materials. The method of obtaining bioethanol from renewable non-demanded raw materials - fallen leaves - was improved. The technique allows to increase the bioethanol yield due to more effective hydrolysis of hard-hydrolysable polysaccharides. Further development of the study of the differences in

Qualification Methods of Al2O3 Injection Molding Raw Materials

International Nuclear Information System (INIS)

Egész, Á; Gömze, L A

2015-01-01

For producing ceramic arc tube parts (plugs), there are used two different major components for producing injection molding raw material (feedstock): high purity alumina powder as the main component, and an organic paraffin wax as a binder material. It is expressly important to know the material, physical and chemical properties of these components, since mainly these have effect on the homogenity of feedstock, and therefore on the quality of end product. In this research, both of the main components and the moldable raw material was investigated by visual, physical, and thermal methods. As most important and main statement, the researchers found that the dynamic viscosity of raw material depends more on the applied temperature, than on the deformation speed gradient.Applied analitycal methods were laser granulometry, sieve analysis, differential thermal analysis and rheology analysis. (paper)

Use of raw materials in the United States from 1900 through 2014

Science.gov (United States)

Matos, Grecia R.

2017-08-22

The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.

Study of chemisrty and hydrolysates drying parameters of feather-downy raw material

OpenAIRE

LISITSYN A.B.; KRIGER O.V.; MITROKHIN P.V.

2016-01-01

The article describes chemical and amino acid composition of feather-downy raw material. It determines the mass fraction of crude protein, crude fiber, ash, calcium, phosphorus, sodium in the samples of feather-downy raw material. It is stated that the waste from poultry processing obtained from hens of all the studied species are characterized by a high content of crude protein and low in crude fiber and ash. The most valuable feather-downy raw material regarding protein is waste containing ...

Radiation sterilization of some cosmetic raw materials and preparations

International Nuclear Information System (INIS)

Achmatowicz-Szmajke, T.; Bryl-Sandelewska, T.; Galazka, M.

1979-01-01

The problem of microbiological purity of cosmetic preparations is discussed. Some results obtained on the influence of ionizing radiation on organoleptic and physicochemical properties of some cosmetic raw materials and final products are reported. The samples of raw materials and the final products were irradiated with a 10 MeV electron beam from an LAE 13/9 linear accelerator located in INR. The doses delivered to the materials were 0.5 - 2.3 Mrad (5-23 kGy). Immediately after irradiation, organoleptic estimations were made and over the next few days physicochemical investigations were performed. Non-irradiated samples were investigated together with irradiated ones. (T.I.)

Aluminium reprocessing with local mineral raw material

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2002-01-01

With the purpose of utilization of ice sediment, receiving from mud fields solutions and flotation tails and at using local aluminium and fluorine-containing raw material was elaborated fundamental technologic scheme presented in this chapter of book

European initiative on cdio in raw material programmes

NARCIS (Netherlands)

Edelbro, Catrin; Hulthén, Erik; Clausen, Elisabeth; Tanner, David; Herrera Herbert, Juan; Jonsson, Kristina; Bealieu, Stephan; Kamp, A.; Försth, Michael

2017-01-01

One of five Knowledge and Innovation Communities (KICs), was launched in Europe in 2014 and has its focus on exploration, extraction, mineral processing, metallurgy, recycling and material substitution of raw materials. To reach the vision, where the European Union’s industrial strength is based on

One step sintering of homogenized bauxite raw material and kinetic study

Science.gov (United States)

Gao, Chang-he; Jiang, Peng; Li, Yong; Sun, Jia-lin; Zhang, Jun-jie; Yang, Huan-ying

2016-10-01

A one-step sintering process of bauxite raw material from direct mining was completed, and the kinetics of this process was analyzed thoroughly. The results show that the sintering kinetics of bauxite raw material exhibits the liquid-phase sintering behavior. A small portion of impurities existed in the raw material act as a liquid phase. After X-ray diffraction analyses, scanning electron microscopy observations, and kinetics calculations, sintering temperature and heating duration were determined as the two major factors contributing to the sintering process and densification of bauxite ore. An elevated heating temperature and longer duration favor the densification process. The major obstacle for the densification of bauxite material is attributed to the formation of the enclosed blowhole during liquid-phase sintering.

Polymer Industrial Floors - The Possibility of Using Secondary Raw Materials from Solar Panels

OpenAIRE

J. Kosikova; B. Vacenovska; M. Vyhnankova

2014-01-01

The paper reports on the subject of recycling and further use of secondary raw materials obtained from solar panels, which is becoming a very up to date topic in recent years. Recycling these panels is very difficult and complex, and the use of resulting secondary raw materials is still not fully resolved. Within the research carried out at the Brno University of Technology, new polymer materials used for industrial floors are being developed. Secondary raw materials are ...

Irradiation as an alternative environmentally friendly method for microbiological decontamination of herbal raw material

International Nuclear Information System (INIS)

Dragusin, M.; Rotaru, R.

2000-01-01

Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the microorganisms present and must not reduce the sensory and technological qualities of the commodities. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods are recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process. Under the prevailing production and handling conditions, most herbs contain a large number of microorganisms what is a serious problem in the production of therapeutical preparations. For several years the most widely used methods for decontamination of herbs was fumigation with ethylene oxide or methyl bromide. Both methods today banned in most countries. Irradiation is an alternative and safe method for effective reducing the microbial contamination of herbal raw materials. The following raw materials have been examined: Folium Cynara, Folium Plantago, Flos Chamomillae, Semen Sylibum Marianum and Folium Farfara. The content of biologically active compounds before and after irradiation of the raw materials did not change in a significant degree after irradiation. The dose of radiation for herbals raw materials was 10 kGy. There are two groups of raw materials: - The raw materials designed for preparing granulates, tablets, dragees, capsules, aqueous extracts, infusions, macerations and preparations for external use; - The raw materials assigned for preparing alcoholic preparations, isolated compounds, oil preparations and essential oils. The medical herbs and herbal raw materials before their

Radioactivity in polluted cement and its raw materials

International Nuclear Information System (INIS)

Khan, K.; Aslam, M.; Orfi, S.D.

1999-01-01

Samples of portland cement manufactured in the North West frontier Province (NWFP) of Pakistan and its different raw materials have been investigated applying gamma-spectrometric techniques for natural gamma-emitting radionuclides. A high purity germanium detector (HPGE) was used for data acquisition. Average values of the total specific activity (in Bq.kg/sup -1/ ) due to all the three radionuclides (/sub 40/K, /sup 226/Ra and /sup 232/Th) were found to be 327.7+ - 168.2 for portland cement; 104.4 + - 21.1 for limestone; 193.2+ - 50.4 for gypsum; 890.4 + - 86.5 for state and 545.6+ - 56.6 for latrite. The average specific activities due to /sup 40/K in Portland cement and all the raw materials were found to be higher as compared to /sub 226/Ra and /sup 232/Th in the respective materials. It is concluded that such materials do not pose any health problem and are not a major source of radiation hazards. However, The data can be utilized in determining radioactivity associated with other building materials. (author)

Quantitative analysis of raw materials mining of Sverdlovsk region in Russia

Science.gov (United States)

Tarasyev, Alexander M.; Vasilev, Julian; Turygina, Victoria F.

2016-06-01

The purpose of this article is to show the application of some qualitative methods for the analysis of a dataset for raw materials. The main approaches used are related to the correlation analysis and forecasting with trend lines. It is proved that the future mining of particular ores can be predicted on the basis of mathematical modeling. It is also shown that there exists a strong correlation between the mining of some specific raw materials. Some of the revealed correlations have meaningful explanations, and for others one should look for sophisticated interpretations. The applied approach can be used for forecasting of raw materials exploitation in various regions of Russia and in other countries.

Raw materials for the energy supply of the future. Geology, markets, environmental influences

International Nuclear Information System (INIS)

Hagelueken, Christian; Thauer, Rudolf K.; Buchholz, Peter; Gutzmer, Jens; Littke, Ralf; Angerer, Gerhard; Wellmer, Friedrich-Wilhelm

2015-01-01

More and more metals are needed to expand modern energy technologies, but we can not completely dispense with fossil raw materials and biomass in the near future either. Are the incidence of the conversion of energy sources sufficient? The analysis of the academy project ''Energy Systems of the Future'' (ESYS) comes to the conclusion that geologically enough raw materials are available. The challenge, however, is to make the supply safe, affordable and environmentally and socially compatible. The analysis explains the mechanisms of action on the global commodity markets and identifies supply risks. These include, for example, sudden demand on the international markets as well as the unequal distribution of the world's raw material reserves. This is followed by the analysis approaches, in order to recognize warning signals for potential raw material bottlenecks in time, to develop evasive strategies and to secure the raw material supply for the energy turnarounds. For example, the expansion of recycling can help to reduce the dependence on metal imports. In mining, on the other hand, innovative technologies have to be developed in order to improve the exploration and utilization of the deposits. By establishing binding environmental and social standards, the extraction of raw materials could also become more sustainable. The analysis also highlights the importance of bioenergy and fossil raw materials, such as oil and natural gas, for energy generation. The authors describe the advantages and disadvantages of these energy carriers and the measures that can be used to reduce environmental pollution such as greenhouse gas emissions. [de

Oat raw materials and bakery products - amino acid composition and celiac immunoreactivity.

Science.gov (United States)

Mickowska, Barbara; Litwinek, Dorota; Gambuś, Halina

2016-01-01

The aim of this study was to compare the biochemical and immunochemical properties of avenins in some special oat raw materials and additionally the possibility of using them as a raw material for the gluten-free bakery products. The compared oat raw materials were - oat flakes, commercial oat flours (including gluten-free oat flour) and residual oat flour, which is by-product of β-glucan preparation. Biochemical characteristic included amino acid compositions and SDS-PAGE profiles of extracted avenins. The immunochemical reactivity with polyclonal anti-gluten and monoclonal anti-gliadin antibodies was evaluated qualitatively and quantitatively by immunoblotting and ELISA methods. Additionally, experimental bakery products made of examined raw materials were assessed according to their suitability for the celiac patients' diet. The highest protein content was measured in the β-glucan preparation "Betaven" and gluten-free oat flour. Proteins of all materials are rich in glutamic and aspartic acid, leucine and arginine. Proportions of amino acids in avenins extracted from most of oat raw materials are similar, excluding gluten-free oat flour, which has a very low avenin content and proportions of individual amino acids are different. The SDS-PAGE protein pattern consisted of proteins with molecular weight of about 25-35 kDa. Polyclonal anti-gluten anti-body recognized all protein fractions of molecular weight higher than 20 kDa. Quantitative ELISA analysis shows that the majority of samples has a gliadin-like protein content within the range of 80-260 mg/kg, excluding gluten-free flours and corresponding bakery products. Altogether, β-glucan preparation has extremely high level of gliadin-like proteins. In the examined oat raw materials and foods the contents of immunoreactive amino acid sequences exceeded the limit of 20 mg/kg (considered as gluten-free) except for gluten-free flours (oat and  the prepared mixture) and the bakery products based on gluten

Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

Directory of Open Access Journals (Sweden)

Strigáč Július

2015-11-01

Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

Characterization of silica quartz as raw material in photovoltaic applications

Energy Technology Data Exchange (ETDEWEB)

Boussaa, S. Anas, E-mail: sabiha.anas@gmail.com; Kheloufi, A.; Kefaifi, A.; Kerkar, F. [Division croissance cristalline et procédés métallurgiques CCPM Centre de recherche en technologie des semi-conducteurs pour l’énergétique (C.R.T.S.E) 02 Bd Frantz Fanon BP. 140 Alger 7 merveilles, Alger 16200 (Algeria); Zaourar, N. Boutarek [Laboratoire des technologies des matériaux, USTHB, B.P. 32 El Alia, Bab Ezzouar, Alger, Algérie 16111 (Algeria)

2016-07-25

Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansion such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO{sub 2} + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.

Quantitative Analysis of Bioactive Compounds In Extract and Fraction of Star Fruit (Averrhoa carambola L. Leaves Using High Performance Liquid Chromatography

Directory of Open Access Journals (Sweden)

Nanang Yunarto

2017-05-01

Full Text Available Starfruit (Averrhoa carambola L. is potential as raw material for medicine, native in tropic areas, including Indonesia. According to other study report, starfruit leaves containing flavonoids apigenin and quercetin as potential anti-inflammatory and anticancer agents. The raw material for the drug in Indonesia mostly obtained through imports from other countries. In order to support the independence of traditional medicine raw materials, it is important to standardize the quality of traditional medicine raw materials, in this case is star fruit leaves by High Performance Liquid Chromatography (HPLC method. The sample used is star fruit leaves extract obtained from maceration process using ethanol 70%; water fraction, ethyl acetate and hexane fractions obtained from fractionation process of the ethanolic extract. Physical parameters analyzed in sample include appearance, color, odor, taste, extract yield, water content, loss of drying, total ash content, residual solvent. Chemical parameters analyzed include apigenin and quercetin contents. The results shows that star fruit leaves used in this study meet the standards of Indonesian Herbal Pharmacopoeia with highest apigenin and quercetin content are in ethyl acetate fraction.

Raw materials resources classification and characterisation for ...

African Journals Online (AJOL)

Raw materials resources classification and characterisation for ceramic tableware production in Nigeria. PSA Irabor. Abstract. No Abstract. Journal of Applied Science, Engineering and Technology Vol. 2(1) 2002: 48-52. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

Recovery of the secondary raw materials, recycling

International Nuclear Information System (INIS)

Chmielewska, E.

2010-01-01

In this chapter the recovery and recycling of secondary raw materials is explained. This chapter consists of the following parts: Paper and tetrapaks; Car wrecks; Scrap metal; Plastics; Used tires; Electrical and electronic equipment; Glass; Accumulators and batteries; Spent oil; Low-and non-waste technology.

Study on optimum length of raw material in stainless steel high-lock nuts forging

Science.gov (United States)

Cheng, Meiwen; Liu, Fenglei; Zhao, Qingyun; Wang, Lidong

2018-04-01

Taking 302 stainless steel (1Cr18Ni9) high-lock nuts for research objects, adjusting the length of raw material, then using DEFORM software to simulate the isothermal forging process of each station and conducting the corresponding field tests to study the effects of raw material size on the stainless steel high-lock nuts forming performance. The tests show that the samples of each raw material length is basically the same as the results of the DEFORM software. When the length of the raw material is 10mm, the appearance size of the parts can meet the design requirements.

INTRAW, the EU Observatory for raw materials: fostering international cooperation and developing new opportunities

Science.gov (United States)

Correia, Victor; Allington, Ruth; Keane, Christopher

2016-04-01

A secure supply of raw materials is a European priority that extends beyond country borders and national policies. Recent European initiatives have pioneered the development of an EU strategy on raw materials emphasizing the concept of the "added value chain", which continues to pursue the three pillar strategy to: (1) ensure the fair and sustainable supply of raw materials from international markets, promoting international cooperation with developed and developing countries; (2) foster sustainable supply of raw materials from European sources, and (3) reduce consumption of primary raw materials by increasing resource efficiency and promoting recycling. This contribution presents the Horizon 2020 funded project INTRAW, the objective of which is to establish the European Union's International Observatory for Raw Materials. The creation and maintenance of the European Union's International Observatory for Raw Materials is designed to have a strong impact in two dimensions: 1. To narrow the existing gap in aspects of the raw materials knowledge infrastructure in the EU by providing a link with the same knowledge infrastructure in technologically advanced reference countries. This should contribute to the harmonization of mineral policies all over the EU, by providing data that enables evidence-based policies and appropriate, cost-effective management, planning and adaptation decisions by the public sector. This will benefit businesses, industry and society. The Observatory will also provide to policy makers in the EU and its Member States the data they need to facilitate discussion in multilateral forums. 2. To enable a better alignment of the R&I activities among the individual EU members and international cooperation countries AND between the European Union and international cooperation countries by boosting synergies with international research and innovation programmes. This way the EU's role and scientific capabilities in the raw materials area will be

THE PAPER CHARACTERISTICS FROM COMBINATION OF RICE HUSKS AND EMPTY FRUIT BUNCHES

OpenAIRE

Yuli Ristianinsih; Hero Islami; Muhammad Sarwani

2017-01-01

Rice husk and empty fruit bunches are agricultural and plantation wastes which have fiber cellulose and hemicellulose, it can be converted to pulp and paper. This research aims to study the effect of NaOH concentration (2, 4, 6 and 8% w/v) and raw material composition to pulp yield and to study characteristics of the paper combination of rice husk and empty fruit bunches using soda process based on SEM and XRD analysis. This research using soda process because it is suitable for non-wood raw...

Raw materials exploitation in Prehistory of Georgia: sourcing, processing and distribution

Science.gov (United States)

Tushabramishvili, Nikoloz; Oqrostsvaridze, Avthandil

2016-04-01

Study of raw materials has a big importance to understand the ecology, cognition, behavior, technology, culture of the Paleolithic human populations. Unfortunately, explorations of the sourcing, processing and distribution of stone raw materials had a less attention until the present days. The reasons of that were: incomplete knowledge of the archaeologists who are doing the late period archaeology (Bronze Age-Medieval) and who are little bit far from the Paleolithic technology and typology; Ignorance of the stone artifacts made on different kind of raw-materials, except flint and obsidians. Studies on the origin of the stone raw materials are becoming increasingly important since in our days. Interesting picture and situation have been detected on the different sites and in different regions of Georgia. In earlier stages of Middle Paleolithic of Djruchula Basin caves the number of basalt, andesite, argillite etc. raw materials are quite big. Since 130 000 a percent of the flint raw-material is increasing dramatically. Flint is an almost lonely dominated raw-material in Western Georgia during thousand years. Since approximately 50 000 ago the first obsidians brought from the South Georgia, appeared in Western Georgia. Similar situation has been detected by us in Eastern Georgia during our excavations of Ziari and Pkhoveli open-air sites. The early Lower Paleolithic layers are extremely rich by limestone artifacts while the flint raw-materials are dominated in the Middle Paleolithic layers. Study of these issues is possible to achieve across chronologies, the origins of the sources of raw-materials, the sites and regions. By merging archaeology with anthropology, geology and geography we are able to acquire outstanding insights about those populations. New approach to the Paleolithic stone materials, newly found Paleolithic quarries gave us an opportunities to try to achieve some results for understanding of the behavior of Paleolithic populations, geology and

Microbiological decontamination of botanical raw materials and corresponding pharmaceutical products by irradiation

International Nuclear Information System (INIS)

Katusin-Razem, B.; Novak, B.; Razem, D.

2001-01-01

Microbiological contamination typical of botanical raw materials used in the manufacture of pharmaceuticals decreases with the increasing level of processing, on going from flowers and leaves (10 4 -10 8 CFU/g), to fruits and seeds (10 2 -10 6 CFU/g), to liquid extracts (10 4 -10 6 CFU/g), and to dry extracts (10 2 -10 5 CFU/g). At the same time the resistivity of microflora to irradiation, expressed as a dose required for the first 90% reduction, increases along the same assortment as 2, 4, 5 and 5 kGy, respectively. This results in doses between 4 and 30 kGy required to treat typical contamination, or between 10 and 40 kGy for severe cases. The contamination of final products, phyto-therapeutic ointments (10 4 -10 7 CFU/g), is relatively sensitive to irradiation (D first90%red =1 kGy) and usually does not require doses higher than 8 kGy

Evaluation of some heavy metal contaminants in biscuits, fruit drinks ...

African Journals Online (AJOL)

Evaluation of some heavy metal contaminants in biscuits, fruit drinks, concentrates, ... effect in human due to continual consumption of food contaminated with heavy metals gotten from raw materials, manufacturing and packaging processes.

CAN BE BLUEBERRIES THE RISK FOOD AND RAW MATERIAL?

Directory of Open Access Journals (Sweden)

Michal Medvecký2

2012-02-01

Full Text Available Fruits of the highbush blueberries are popular for their beneficial effects on human health and for their excellent sweet-vine taste. Our work is focused on risk assessment of selected elements in relation to the content of bioactive compounds in wild and cultivated of highbush blueberries (Vaccinium corymbosum L.. Anthocyanins are polyphenols that are widely distributed in plants, and contribute to the brilliant blue, red or purple colour in leaves, flowers or fruits. In the samples the antioxidant capacity by the method of Brand – Williams using DPPH (2,2–difenyl-1-pikrylhydrazyl and the content of anthocyanins by the modified method Lapornik in two samples of wild blueberries from different areas of Slovakia (Čertovica and Oravské Veselé and in 6 cultivated varieties highbush blueberry (Bluejay, Bluecrop, Patriot, Berkeley, Brigitta, Nelson were determined. The contents of risky elements - Cd, Pb were assessed by AAS method. The contents of Pb were in all observed samples higher than the maximum limit given by the legislation (cultivated: 0.5612 – 0.9912 mg.kg-1, wild: 0.792 – 0.874 mg.kg-1. The measured content values of Cd were in all samples of blueberries lower than hygienic limit. The highest content of anthocyanins from analysed samples was in wild blueberries from surrouding Čertovica 4870.125 ± 22.803 mg.dm-3, but in this sample was simultaneously the lowest antioxidant capacity of 61.15 ± 1.002 %. The highest antioxidant capacity was measured in sample of cultivated variety Bluejay 87.175 ± 0.45 %. It is important to carry out monitoring of heavy metals to consumption of safe food raw materials and foodstuffs.

Globalization and its influence to the availability of the Raw material sources

Directory of Open Access Journals (Sweden)

Vodzinský Vladimír

2002-12-01

Full Text Available Process of globalization does not lead only to concentration of physical and financial capital, and to centralization of its managing, what can be considered as its main signs, but at same time it gives whole raw of new claims to realization of technologies and their material basis.One of very important claims is also change in structure and volume of raw materials, that is gradually viewing in increased change from consumption of so-called classical raw materials, without which it is not possible to create basic components of information technologies.Information technologies are then creating important basis for quickly developed new branches of economy.

IMPROVING THE SYSTEM OF RAW MATERIAL SUPPLY OF THE MEAT INDUSTRY

Directory of Open Access Journals (Sweden)

A. M. Bukreev

2013-01-01

Full Text Available The article describes the characteristics of the process of improving the system raw materials supply of meat industry and presents the main factors, criteria, principles and algorithm rational distribution of the meat industry. The relevance of the research topic, in a globalized economy and Russia's accession to the WTO, caused by necessity to improve the system of raw material supply domestic enterprises and enhancing food security.

Use of a new borate raw material for glaze formulation

International Nuclear Information System (INIS)

Gomez-Tena, M. P.; Moreno, A.; Bou, E.; Cook, S.; Galindo, M.

2010-01-01

The Rio Tinto Minerals company has developed a new borate (E-4972), which can be used in glaze formulation (patent WO 2007/148101). This new borate, synthesised by low-temperature calcination, fundamentally contributes five oxides: silicon oxide (SiO 2 ), aluminium oxide (Al 2 O 3 ), boron oxide (B 2 O 3 ), calcium oxide (CaO), and sodium oxide (Na 2 O), its content in B 2 O 3 being between 10 and 11% by weight. It is largely amorphous, and quartz is the major crystalline phase present. The characteristics of this new borate, such as its low solubility and ability readily to form glassy phase, enable it to be used as a raw material in glaze compositions. Its suitability for glaze formulation has been the result of several years research in collaboration with the Instituto de Tecnologia Ceramica. In this paper, the feasibility has been studied of fabricating ceramic glazes by using a new synthetic borate raw material that contributes boron to the glaze composition without this needing to be done in fritted form. It has been possible to obtain fired glazes with similar technical and aesthetics characteristics to those obtained from industrial glaze compositions that contain typical frits in their compositions, thus enabling glazes to be formulated by using the new synthetic boron raw material. The results obtained show that this new raw material (E-4972) is particularly appropriate for use in producing glazes with low gloss at high temperature. (Author) 15 refs.

The Influence of the Fruits Addition on the Quality Characteristics of Yogurt

OpenAIRE

Zorica Vosgan; Anca Dumuta; Cristina Mihali; Lucia Mihalescu; Thomas Dippong; Alina Moldovan

2016-01-01

Yogurt is considered a healthy food and by incorporating fruits the flavor and its nutritional value are improved. The objective of this study consists in obtaining and characterization of functional dairy products with added fruits, of yogurt type. The raw material used for obtaining the acid dairy products is cow milk, in which there were incorporated fruits: cherry, bananas and oleaginous fruits (nuts). The evolution in time of the acidity during fermentation is influenced by the addition ...

Study of mechanoactivation of tungsten-molybdenum containing raw material in gas-jet mill

International Nuclear Information System (INIS)

Agnokov, T.Sh.; Gorobets, L.Zh.; Martynenko, V.P.; Fedorov, Yu.P.; Krakhmaleva, M.T.; Sokolova, L.A.

1988-01-01

Investigation is aimed at intensifying autoclave-soda leaching of tungsten-molybdenum-containing raw material. Connection of reactivity and physicochemical properties of crushed tungsten-molybdenum-containing products under different gas-jet crushing parameters is investigated. Optimal technological indices of hydrometallurgical reprocessing of tungsten-molybdenum-containing raw materials and products processed by gas-jet technique are given. The results obtained point out to perspectiveness of applying gas-jet technique of thermomechanical processing for intensifying and increasing the quality of tungsten- and molybdenum-containing raw materials and products of hydrometallurgical production

Becquerel in raw fruit and vegetables?

International Nuclear Information System (INIS)

Heilgeist, M.

1989-01-01

After a general introduction and definition of the basic terms, the quantity of radionuclides of natural and artificial origin in our environment is shown. The specific activity of Cs-134 and Cs-137 in fruit and vegetables before and after the accident in Chernobyl is demonstrated. Finally, the quantity of the radioactivity consumed by the human being with fruit and vegetable is compared with the values of the total food consumption. (orig./HP) [de

Natural radioactivity and human exposure by raw materials and end product from cement industry used as building materials

International Nuclear Information System (INIS)

Stojanovska, Z.; Nedelkovski, D.; Ristova, M.

2010-01-01

During the manufacturing process in the cement industry, raw materials of different levels of natural radioactivity are utilized. In this study we present the radiological impact of cements as a building material and the different raw materials used in their manufacture. A total of 218 samples of raw materials and their end product cements were collected from the cement industry of Macedonia (The Former Yugoslav Republic) during the period 2005-2007. The specific activities, evaluated by gamma spectrometry analysis, showed the highest mean specific activity in fly ash ( 226 Ra, 107 ± 45 Bq kg -1 ; 232 Th, 109 ± 30 Bq kg -1 ; 40 K, 685 ± 171 Bq kg -1 ), which is used as a raw material. However, the final cement product usually has relatively lower activity compared with the activity of the raw material and the mean specific activity of the final cement products were lower ( 226 Ra, 42 ± 10 Bq kg -1 ; 232 Th, 28 ± 6 Bq kg -1 ; 40 K, 264 ± 50 Bq kg -1 ). The radium equivalent activity and the hazard index were calculated for each sample to assess the radiation hazard. The mean annual effective dose originating from the cements was found to be 111 ± 22 μSv y -1 , which is below the recommended EC limit of 300 μSv y -1 .

Material Classification Using Raw Time-of-Flight Measurements

KAUST Repository

Su, Shuochen

2016-12-13

We propose a material classification method using raw time-of-flight (ToF) measurements. ToF cameras capture the correlation between a reference signal and the temporal response of material to incident illumination. Such measurements encode unique signatures of the material, i.e. the degree of subsurface scattering inside a volume. Subsequently, it offers an orthogonal domain of feature representation compared to conventional spatial and angular reflectance-based approaches. We demonstrate the effectiveness, robustness, and efficiency of our method through experiments and comparisons of real-world materials.

Importance and possibilities of secondary cycles (recycling), substitution and innovation in mineral raw and primary material supply

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Part 1-4 of the series ''The basis of raw materials supply'' is intended to bring about a better understanding of the ''Concept for the supply of Austria with mineral raw- and primary materials''. Part 3 deals with recovery of raw material from old- and waste material as an important contribution to an extension of the supply's basis and to an improvement of raw material utilization.

Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.

Science.gov (United States)

Black, R E; Hurley, F J; Havery, D C

2001-01-01

Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.

Mineral raw materials for power production in legislation of the Republic of Croatia

International Nuclear Information System (INIS)

Matisa, Z.

1999-01-01

According to the Constitution of the Republic of Croatia, mineral wealth is a public good of legal interest to the Republic of Croatia and enjoys its special protection. The Mining Law establishes that mineral wealth (including mineral resources that are used for power production) is the property of the Republic of Croatia. Among other mineral raw materials, this refers to mineral raw materials that are used for power production: coal, oil, natural gas, radioactive mineral raw materials and geothermal waters. These mineral resources are as almost all other mineral raw materials with the exception of geothermal waters, an unrecoverable natural resource. The right to use that natural resource may be granted only by a concession. The mining legislation provides for exploration and exploitation of mineral raw materials. Exploration of oil and gas is considered to comprise operations and testing with the aim to establish the existence, position and form of oil and natural gas deposits, their quality and quantity, as well as exploitation conditions. Exploitation of oil and natural gas is considered to comprise extraction from deposits, refining and transport, as well as disposal in geological structures. Mineral raw materials used in power production amount to 63% of national total primary energy production, and they cover 33% of total power consumption in the country. Legislation in the Republic of Croatia, which refers to exploration and exploitation of oil and natural gas, allows economic utilization of that unrecoverable natural wealth to run smoothly and in compliance with practices in our European environment. (author)

Extraction of protoactinium from silicaceous raw material

Energy Technology Data Exchange (ETDEWEB)

Broda, E.

1946-07-01

This report was written by E. Broda and P.K. Wright at the Cavendish Laboratory (Cambridge) in March 1946 and is about the Extraction of protoactinium from a silicaceous raw material. In this report the isolation of Pa on Er carrier is described and it includes the experiment description and the discussion of the results. (nowak)

Evolution and characterization of eggshell as a potential candidate of raw material

Directory of Open Access Journals (Sweden)

T. Zaman

Full Text Available Abstract Characterization of both uncalcined and calcined eggshells was done in this work. Raw eggshells turned out as a good source of calcite phase. Calcined eggshells had a mixture of lime and portlandite phase. A significant impact of calcination temperature on the percentage of generated phases was observed. Qualitative as well as semi-quantitative phase analysis, morphological characterization and physical property estimation was done for the produced powder. The influence of synthesized raw material on soil stabilization and biomaterial formation was further assessed. The eggshell turned out as a potential source of raw material for various sectors.

Effect of the raw materials processing on their dustiness

International Nuclear Information System (INIS)

López Lilaoa, A.; Juárezb, M.; Sanfelix Fornera, V.; Mallol Gascha, G.; Monfort Gimeno, E.

2017-01-01

During the handling and/or processing of powdered materials in the CERAMICS INDUSTRY, one of the most important risks regarding the environmental and occupational health is the potential generation of dust. In this regard, a parameter of great interest is the dustiness of the processed materials; this parameter quantifies the tendency of the powdered materials to generate dust when handled. In this study, to determine the dustiness of a ceramic raw material composition (mixture of the body raw materials), the continuous drop method has been used. This test apparatus was selected because it is considered to better simulate how ceramic materials are handled in the CERAMICS INDUSTRY. The obtained results show that the dustiness of the same ceramic composition exhibits significant changes during the manufacturing process, depending on the presentation form. In this regard, the dry milling sample presents the highest dustiness, which can be significantly reduced (>75%) applying the the moisturization and agglomeration. The obtained results also shown that the best presentation form, regarding the minimization of the dust generation, is achieved in the spray-drying process, where the dustiness is reduced by 95%. [es

Replacement of reserves zinc based on the recycling of technogenic raw materials

Directory of Open Access Journals (Sweden)

Olga Sergeevna Bryantseva

2013-06-01

Full Text Available In the article, the perspective trends of the expansion of the mineral-ore base of the Russian producers of zinc by recycling of technogenic raw materials are considered. The important role of recycling of resources for sustainable development of society and improve the environmental safety is justified. The main structural and dynamic characteristics of the use of mineral resource base for the production of zinc in Russia are considered. Raw materials opportunities and constraints for the development of zinc production are analyzed. In the paper, the structure and dynamics of the use of recycled materials by the largest producer of zinc in Russia are investigated. The methodical approach to the estimation of effectiveness of the industrial processing of technogenic metallurgical raw materials with the strategic flexibility of the implementation of projects is proposed and approved. The estimation of the effectiveness of a complex industrial processing of metallurgical zinc-containing dusts in a real production is carried out. The value of the strategic flexibility of the project of the industrial processing of the zinc-containing technogenic raw material is determined on the basis of the developed systematic approach. The value of the processes of recycling for sustainable production of zinc in Russia is revealed.

Anthropogenic materials and products containing natural radionuclides. Pt. 1a. Radiation properties of raw materials and waste materials. A literature study

International Nuclear Information System (INIS)

Reichelt, A.; Roehrer, J.; Lehmann, K.H.

1995-12-01

Cased on the literature study, the publication presents relevant data on raw materials and wastes containing natural radionuclides. The study is part 1a of the project on ''Anthropogenic materials and waste materials containing natural radionuclides''. Part 1 of the project gives data and information on about 100 different materials and wastes or products for household or industrial applications which contain significant amounts of natural radioactivity. In addition, part 1 presents for some of these materials information on their applications, consumption, radioactivity and resulting radiation doses. The raw materials and waste materials on the list in part 1 are characterised in this 1a report. Wherever appropriate, two or more materials are dealt with in one chapter, as e.g. felspar and felspar sands (pegmatite), talcum, and soapstone. The wastes are dealt with in the chapters discussing the relevant raw materials. The information given is as derived from the literature and does not include comments or evaluation by the authors of this report. Whenever the literature study did not yield information on radiological aspects of a material on the list, an appropriate notice is given. (Orig./DG) [de

Raw material consumption of the European Union--concept, calculation method, and results.

Science.gov (United States)

Schoer, Karl; Weinzettel, Jan; Kovanda, Jan; Giegrich, Jürgen; Lauwigi, Christoph

2012-08-21

This article presents the concept, calculation method, and first results of the "Raw Material Consumption" (RMC) economy-wide material flow indicator for the European Union (EU). The RMC measures the final domestic consumption of products in terms of raw material equivalents (RME), i.e. raw materials used in the complete production chain of consumed products. We employed the hybrid input-output life cycle assessment method to calculate RMC. We first developed a highly disaggregated environmentally extended mixed unit input output table and then applied life cycle inventory data for imported products without appropriate representation of production within the domestic economy. Lastly, we treated capital formation as intermediate consumption. Our results show that services, often considered as a solution for dematerialization, account for a significant part of EU raw material consumption, which emphasizes the need to focus on the full production chains and dematerialization of services. Comparison of the EU's RMC with its domestic extraction shows that the EU is nearly self-sufficient in biomass and nonmetallic minerals but extremely dependent on direct and indirect imports of fossil energy carriers and metal ores. This implies an export of environmental burden related to extraction and primary processing of these materials to the rest of the world. Our results demonstrate that internalizing capital formation has significant influence on the calculated RMC.

Efficiency of raw materials. Relief of the economy, environmental protection; Rohstoffeffizienz. Wirtschaft entlasten, Umwelt schonen

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-11-15

In the contribution under consideration, the Federal Statistical Office (Wiesbaden, Federal Republic of Germany) and the Federal Environmental Agency (Dessau-Rosslau, Federal Republic of Germany) present actual data and analyses from environmentally economic total computations. In Germany, the use of raw materials became more efficient. Thus, 580 tons of raw materials per million Euro of gross domestic product were needed in the year 2008, while still 680 tons of raw materials were needed in the year 2000. The economical handling of natural resources relieves the environment and enables economic chances for individual companies and national economy. The lowering of environmental effects is to be in the focus of withdrawal and use of raw materials. This requires a stronger reduction of the consumption of raw materials. Savings potentials and an increased efficiency must be aspired in the short and medium term. The politics must create suitable incentives and framework conditions. The contribution under consideration presents new activities and strategies in order to achieve these targets.

Assessment of physicochemical characteristics and hygienic practices along the value chain of raw fruit juice vended in Dar es Salaam City, Tanzania.

Science.gov (United States)

Nonga, Hezron E; Simforian, Edeltruds A; Ndabikunze, Bernadette K

2014-10-01

Fresh fruit juice is an essential component of human diet and there is considerable evidence of health and nutritional benefits. However, nature of the fruits used in juicing and unhygienic processes in the value chain may cause poor quality of juice. This cross- sectional study was conducted to assess physicochemical characteristics and hygienic practices along the value chain of raw fruit juice vended in Dar es Salaam, Tanzania. A total of 90 juice vendors were interviewed. Ninety juice samples were collected and analysed for physicochemical quality. The pH of juices ranged between 2.7 and 6.4, acidity 0.01% and 1.3% and, total soluble solids ranged between -1.5 and 18.04 °Brix. Most juices (67.8%) had -Brix levels below Codex recommended values classified as weak and watery. Juices were made of mango, passion, tamarind, sugar cane and mixture of these fruits sourced from open markets in the city. Water for washing of fruits and dilution of juices was from deep wells (53.3%) and taps (46.7%). About one third (37.8%) of the juice vendors didn't wash the fruits before juicing and 44.4% didn't boil water for juice dilution. Juice extraction was done by kitchen blenders, boiling in water and squeezing by simple machines. Juice pasteurization was not done. The majority of vendors (78.9%) stored juices in plastic buckets and juice was sold in glass cups, reused plastic bottles and disposable cups. Vending sites were restaurants, bus stands and along roadsides. The majority of premises (78.9%) were in unhygienic condition that likely encouraged or introduced contaminants to the juices. It is concluded that, the overall handling, preparation practices and physicochemical quality of raw fruit juices vended in Dare es Salaam City are poor. The government should educate the vendors on food safety and hygiene as well as enforcing regular monitoring of the quality of street fruit juices.

THE PAPER CHARACTERISTICS FROM COMBINATION OF RICE HUSKS AND EMPTY FRUIT BUNCHES

Directory of Open Access Journals (Sweden)

Yuli Ristianingsih

2017-10-01

Full Text Available Abstract- Rice husk and empty fruit bunches are agricultural and plantation wastes which have fiber cellulose and hemicellulose, it can be converted to pulp and paper. This research aims to study the effect of NaOH concentration (2, 4, 6 and 8% w/v and raw material composition to pulp yield and to study characteristics of the paper combination of rice husk and empty fruit bunches using soda process based on SEM and XRD analysis. This research using soda process because it is suitable for non-wood raw materials, low cost operations and not use sulfur compounds. Dry raw materials are mixed with NaOH and digesting using autoclave (100°C, 1 atm for 60 minutes. NaOH concentration optimum used in the pulping process a combination rice husk and empty fruit bunches (1:3, 1:2, 1:1, 2:1 and 3:1 and then cooled for 30 minutes. Pulp is bleached with NaClO 5.25% (v / v, then formed and dried as paper. The lowest pulp yield obtained in a ratio of 2: 1 is 27.6%. Based on the observation of SEM known the fiber of rice husk and empty fruit bunches is 5.88 to 9.8 μm and 8.82 to 14.71 μm, while based on XRD observations, chemical treatment can improve the characteristic of peak intensity on paper combination. The highest advances of peak intensity in the 1:3 ratio is 71.28% (cellulose I dan 83.33% (cellulose II.

THE PAPER CHARACTERISTICS FROM COMBINATION OF RICE HUSKS AND EMPTY FRUIT BUNCHES

Directory of Open Access Journals (Sweden)

Yuli Ristianinsih

2017-10-01

Full Text Available Rice husk and empty fruit bunches are agricultural and plantation wastes which have fiber cellulose and hemicellulose, it can be converted to pulp and paper. This research aims to study the effect of NaOH concentration (2, 4, 6 and 8% w/v and raw material composition to pulp yield and to study characteristics of the paper combination of rice husk and empty fruit bunches using soda process based on SEM and XRD analysis. This research using soda process because it is suitable for non-wood raw materials, low cost operations and not use sulfur compounds. Dry raw materials are mixed with NaOH and digesting using autoclave (100°C, 1 atm for 60 minutes. NaOH concentration optimum used in the pulping process a combination rice husk and empty fruit bunches (1:3, 1:2, 1:1, 2:1 and 3:1 and then cooled for 30 minutes. Pulp is bleached with NaClO 5.25% (v / v, then formed and dried as paper. The lowest pulp yield obtained in a ratio of 2: 1 is 27.6%. Based on the observation of SEM known the fiber of rice husk and empty fruit bunches is 5.88 to 9.8 μm and 8.82 to 14.71 μm, while based on XRD observations, chemical treatment can improve the characteristic of peak intensity on paper combination. The highest advances of peak intensity in the 1:3 ratio is 71.28% (cellulose I dan 83.33% (cellulose II.

Comparison of Biochars Characteristics from Different Raw Materials

OpenAIRE

SUN Tao; ZHU Xin-ping; LI Dian-peng; GU Zhu-yu; ZHANG Jia-xi; JIA Hong-tao

2017-01-01

Biochar is the carbon-rich product from biomass under limited supply of oxygen. Biochar has been well recognized in enhancing terrestrial carbon sequestration and greenhouse gas mitigation as well as in improving soil fertility and plant productivity. To explore the differences of biochars produced from different raw materials, six biochar samples made from alfalfa straw, wheat straw, cotton straw, grape vines, sludge and lignite were selected as test material. Qualitative and quantitative an...

Utilization of Iron Ore Tailings as Raw Material for Portland Cement Clinker Production

Directory of Open Access Journals (Sweden)

Li Luo

2016-01-01

Full Text Available The cement industry has for some time been seeking alternative raw material for the Portland cement clinker production. The aim of this research was to investigate the possibility of utilizing iron ore tailings (IOT to replace clay as alumina-silicate raw material for the production of Portland cement clinker. For this purpose, two kinds of clinkers were prepared: one was prepared by IOT; the other was prepared by clay as a reference. The reactivity and burnability of raw meal, mineralogical composition and physical properties of clinker, and hydration characteristic of cement were studied by burnability analysis, differential thermal analysis, X-ray diffraction, and hydration analysis. The results showed that the raw meal containing IOT had higher reactivity and burnability than the raw meal containing clay, and the use of IOT did not affect the formation of characteristic mineralogical phases of Portland cement clinker. Furthermore, the physical and mechanical performance of two cement clinkers were similar. In addition, the use of IOT was found to improve the grindability of clinker and lower the hydration heat of Portland cement. These findings suggest that IOT can replace the clay as alumina-silicate raw material for the preparation of Portland cement clinker.

TATA LETAK GUDANG RAW MATERIAL CHEMICAL MENGGUNAKAN METODE SHARED STORAGE DAN REL SPACE

Directory of Open Access Journals (Sweden)

Indramawan Hadi Kuswoyo

2016-04-01

Full Text Available Storage system in the manufacturing industry in this modern era is a very important role especially international scale company, may not directly produce or distribute all of the work unit. this led to the need for raw materials warehouse, warehouse storage systems should not be large in size because if supported by a good inventory of the warehouse to the maximum utilization of the problems faced by the company occurred in the warehouse of raw materials (raw materials. deficiencies in the arrangement of items in the warehouse procedures cause problems in the warehouse, so the warehouse impressed narrow and less structured cause inefficiencies time retrieval and storage of materials, as well as complicate the operator in handling the placement process raw materials. In the method of shared storage and rail space (relationchip chart for the relationship between activity is indicated by activity relationship approach, which shows each activity as a single activity model in the form of a diagram. ARD basic idea of the link between patterns of flow of goods and location of service activities related to production activities. ARD is the development of ARC (activity relationship chart.

Gas condensate--raw material for producing liquid paraffin hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Aliyeva, R.B.; Alikishi-Zade, G.Yu.; Kuliyev, A.M.; Leonidov, A.N.; Pereverzev, A.N.

1980-01-01

The problem of efficient utilization of gas condensates as raw material for removal of a valuable product, liquid paraffins, is examined. A classification of gas condensates is given which is used as raw material for removing these hydrocarbons: gas condensate with high content of n-alkanes (25-40 mass percent), with average content (18-25 mass percent), with low content (12-18 mass percent), light weight fractions compositions, which do not contain fractions up to 200/sup 0/, and also, content ofless than 12% n-alkanes. Gas condensate I-III groups are 30% of the total reserve of gas condensate. Liquid paraffins hydrocarbons, produced from fractions of diesel fuel, which has been removed from Shatlyk gas condensate under conditions which simulate virtual processes of caramide deparaffinization meet all requirements without additional refining.

Agaves as a raw material: recent technologies and applications.

Science.gov (United States)

Narváez-Zapata, J A; Sánchez-Teyer, L F

2009-01-01

Agave plants are a valuable source of raw material due to its fibrous and complex sugar content of their leaves and core, and their bagasse waste can be use for several aims. This plant genus belongs to the Agavaceae family and until now more than 200 species have been described. A large number of Agave species are currently used as raw material in several biotechnological processes. This review shows the reported applications and patents on fields like alcoholic brewages with special reference to Tequila and Mezcal, the isolation and use of compounds such as saponins and agave fructans, and their potential biotechnological application on several human demands. The process to obtain fibers and cellulose, stock feeds, and several miscellaneous extractives are also reviewed. Some possibilities and problems of cultivation are discussed.

Development and Testing the Technology of Complex Transformation of Carbohydrates from Vegetable Raw Materials into Bioethanol

Directory of Open Access Journals (Sweden)

S.P. Tsygankov

2013-07-01

Full Text Available Results of development and testing the tentative technology of sweet sorghum and finger millet processing into bioethanol are described. The carbohydrates content and range of the studied vegetable biomass as the raw material is defined. Bioethanol potential output from sugar sorghum and finger millet carbohydrates and key technological parameters of preparation of both types of vegetable raw material for alcohol fermentation are defined. The concept of the tentative technology of bioethanol production from carbohydrate raw material of the first and second generations is offered. Testing of complex transformation of carbohydrates from vegetable raw materials into bioethanol is performed.

Effects of bagging materials and CaCl2 spray on fruit calcium concentration in fruit-bagged apple trees

International Nuclear Information System (INIS)

Yim, Y.J.; Choi, J.S.; Kim, S.B.

1989-01-01

This experiment was carried out to investigate the effects of bagging materials and CaCl 2 spray on fruit Ca concentration in fruit-bagged apple trees (Malus domestica Borkh.). No difference was noted in fruit Ca concentration among bagging materials during the growing season. And also, there was no difference in fruit Ca concentration between bagged and non-bagged fruits. The fruit flesh Ca concentration of bagged fruits was significantly lower than that of non-bagged fruits in the same tree, which 0.5 % CaCl 2 was sprayed 5 times in the late growing season. The radioactivity of 45 Ca was highest in the sprayed shoot leaves and bark, while only a trace amount was detected in the fruit and shoot proximate to the treated shoot 3 weeks after 3 times application of 45 CaCl 2 (5 micro Ci/ml). As a result, it is confirmed that the Ca once accumulated in a specific part is hardly retranslocated. Therefore, it is concluded that Ca foliar spray to the fruit-bagged tree has no influence on Ca concentration in the fruit

Chemical analysis of raw and processed Fructus arctii by high-performance liquid chromatography/diode array detection-electrospray ionization-mass spectrometry

Science.gov (United States)

Qin, Kunming; Liu, Qidi; Cai, Hao; Cao, Gang; Lu, Tulin; Shen, Baojia; Shu, Yachun; Cai, Baochang

2014-01-01

Background: In traditional Chinese medicine (TCM), raw and processed herbs are used to treat the different diseases. Fructus Arctii, the dried fruits of Arctium lappa l. (Compositae), is widely used in the TCM. Stir-frying is the most common processing method, which might modify the chemical compositions in Fructus Arctii. Materials and Methods: To test this hypothesis, we focused on analysis and identification of the main chemical constituents in raw and processed Fructus Arctii (PFA) by high-performance liquid chromatography/diode array detection-electrospray ionization-mass spectrometry. Results: The results indicated that there was less arctiin in stir-fried materials than in raw materials. however, there were higher levels of arctigenin in stir-fried materials than in raw materials. Conclusion: We suggest that arctiin reduced significantly following the thermal conversion of arctiin to arctigenin. In conclusion, this finding may shed some light on understanding the differences in the therapeutic values of raw versus PFA in TCM. PMID:25422559

Estimation of raw material performance in mammalian cell culture using near infrared spectra combined with chemometrics approaches.

Science.gov (United States)

Lee, Hae Woo; Christie, Andrew; Liu, Jun Jay; Yoon, Seongkyu

2012-01-01

Understanding variability in raw materials and their impacts on product quality is of critical importance in the biopharmaceutical manufacturing processes. For this purpose, several spectroscopic techniques have been studied for raw material characterization, providing fast and nondestructive ways to measure quality of raw materials. However, investigations of correlation between spectra of raw materials and cell culture performance have been scarce due to their complexity and uncertainty. In this study, near-infrared spectra and bioassays of multiple soy hydrolysate lots manufactured by different vendors were analyzed using chemometrics approaches in order to address variability of raw materials as well as correlation between raw material properties and corresponding cell culture performance. Principal component analysis revealed that near-infrared spectra of different soy lots contain enough physicochemical information about soy hydrolysates to allow identification of lot-to-lot variability as well as vendor-to-vendor differences. The identified compositional variability was further analyzed in order to estimate cell growth and protein production of two mammalian cell lines under the condition of varying soy dosages using partial least square regression combined with optimal variable selection. The performance of the resulting models demonstrates the potential of near-infrared spectroscopy as a robust lot selection tool for raw materials while providing a biological link between chemical composition of raw materials and cell culture performance. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

Comparative analysis of secondary metabolites contents in[i] Fragaria vesca[/i] L. fruits

Directory of Open Access Journals (Sweden)

Agnieszka Najda

2014-06-01

Full Text Available [i]Fragaria vesca[/i] (wild strawberry belongs to the Rosaceae family. Besides the leaves ([i]Fragariae folium[/i] and roots ([i]Fragariae radix[/i], the aromatic fruits ([i]Fragariae fructus[/i] of wild strawberry are also herbal materials used in medicine. The aim of this study was to compare the value of phytochemical and antioxidant activity of wild strawberry fruits ([i]Fragaria vesca L[/i].. The fruits were analyzed regarding their secondary metabolites contents (flavonoids, sum of phenolic acids, tannins, anthocyanins, DPPH, depending on the origin of the raw material (from natural habitats vs. cultivation. According to the obtained results, raw material originating from natural habitats contained significantly more flavonoids (0.559 mg∙g [sup]-1[/sup] , compared to fruits harvested from cultivation (0.472 mg∙g [sup]-1[/sup] , on average. Mean concentration of phenolic acids ranged from 1.648 mg∙g[sup] -1[/sup] – 2.348 mg∙g [sup]-1[/sup] , although the wild form was characterized by higher levels of examined substances. Tannins are an important fraction of phenolic compounds; their content in studied fruits ranged from 2.2% (from cultivation – 3.0% (from natural habitats. When comparing the average contents of anthocyanins in the studied materials, it was revealed that remarkably more of these compounds were recorded in wild strawberry fruits harvested from natural habitats vs. those from cultivations: 132 mg∙100 g [sup]-1[/sup] vs. 90 mg∙100 g [sup]-1[/sup] . A difference was indicated with respect to the ability of DPPH radical reduction to diphenylpicrylhydrazine by extracts made of examined fruits.

Raw material selection for object construction

CSIR Research Space (South Africa)

Perlow, J

2017-11-01

Full Text Available on their visual appearance. In particular, we present a method for an agent to recognise the required unseen raw material images and link them to corresponding novel object images. This capability provides an agent with an increased degree of resourcefulness... construction from component parts, and in doing so we provide a benchmark for future work to compare against within Minecraft and ShapeNet domains. II. BACKGROUND Our model is inspired by Siamese neural networks, a class of neural network that includes multiple...

Mineralogy And Raw Material Characterization Of Esie Stone ...

African Journals Online (AJOL)

Electronprobe mineral data of samples of Esie statues is presented as a possible tool for provenance studies. Most of the samples contain talc, chlorite, cummingtonite and rarely tremolite. Other talc-bearing schists are prevalent in the Esie area. However talc-cummingtonite rocks, similar to the raw materials used for the ...

CONTRIBUTION TO THE STATISTICAL INTERPRETATION OF RAW MATERIALS FOR THE CEMENT INDUSTRY OF SPLIT

Directory of Open Access Journals (Sweden)

Miroslav Matijaca

1990-12-01

Full Text Available Up to the last two decades cement was produced from mari called »tupina« (with about 76% CaCOj which is an ideal mixture for cement production. Due to the quantity decrease of this raw material, cement production went on using the mixture of other members of the flysch series: limestones, marls, clay, loess, sandstones a.o. By the analysis of natural materials the CaCO^ content has mostly been proved. Therefore, knowing the correlation of oxides in mineral raw material is of special significance. The article discusses investigation results of the correlation between CaCO-i and other oxides of the raw material (the paper is published in Croatian.

Exploring China's materialization process with economic transition: analysis of raw material consumption and its socioeconomic drivers.

Science.gov (United States)

Wang, Heming; Tian, Xin; Tanikawa, Hiroki; Chang, Miao; Hashimoto, Seiji; Moriguchi, Yuichi; Lu, Zhongwu

2014-05-06

China's rapidly growing economy is accelerating its materialization process and thereby creating serious environmental problems at both local and global levels. Understanding the key drivers behind China's mass consumption of raw materials is thus crucial for developing sustainable resource management and providing valuable insights into how other emerging economies may be aiming to accomplish a low resource-dependent future. Our results show that China's raw material consumption (RMC) rose dramatically from 11.9 billion tons in 1997 to 20.4 billion tons in 2007, at an average annual growth rate at 5.5%. In particular, nonferrous metal minerals and iron ores increased at the highest rate, while nonmetallic minerals showed the greatest proportion (over 60%). We find that China's accelerating materialization process is closely related to its levels of urbanization and industrialization, notably demand for raw materials in the construction, services, and heavy manufacturing sectors. The growing domestic final demand level is the strongest contributor of China's growth in RMC, whereas changes in final demand composition are the largest contributors to reducing it. However, the expected offsetting effect from changes in production pattern and production-related technology level, which should be the focus of future dematerialization in China, could not be found.

Optimizing Pretreatment of Medicinal Raw Materials by RFC Plasma before Extraction

Directory of Open Access Journals (Sweden)

O.Yu. Kuznetsova

2016-06-01

Full Text Available Optimization of the RF-plasma treatment modes of chaga raw materials using the Statistica 6.0 software package has been performed. Mathematical design has been carried out to calculate the optimum parameters of RF-plasma treatment using three plasma-forming gases – argon, air, and nitrogen. Plasma treatment of chaga raw materials has been undertaken at the constant parameters: pressure P = 30.0 Pa, anodic current J = 0.7 A, gas consumption G = 0.04 g/s; the variable parameters were power U = 5.0÷7.0 kV and treatment duration at the high-frequency capacitor category of the lowered pressure t = 30÷60 min. Optimization of four key parameters for extraction of chaga raw materials (solid residue, melanin yield, antioxidant activity of both extract and chaga melanin depending on the chosen plasma-forming gas (argon, air, or nitrogen has been achieved. The optimum modes of RF-plasma treatment allowing to obtain the extracts and melanin of chaga mushroom with the improved physicochemical and antioxidant characteristics have been calculated.

New and non-traditional mineral raw materials deposits, perspectives of use

International Nuclear Information System (INIS)

Beyseev, O.; Beyseev, A.; Baichigasov, I.; Sergev, E.; Shakirova, G.

1996-01-01

Deposits of new and non-traditional kinds of mineral raw material are revealed, explored and prepared to industrial recovery in Kazakstan, that can be used in frames of conversion process to create new materials with unique properties, to prepare base for new technologies elaboration, and to achieve appreciable economic benefit. These deposits are located mostly in geographic and economic conditions of advanced infrastructure and mining works network, favorable for recovery.On the tests results the following is of heaviest interest: RHODUCITE, NEMALITE-CONTAINING CHRYSOTILE-ASBESTOS, NICKEL-CONTAINING SILICATE-ASBOLAN ORES, MEDICINAL MINERALS, SHUNGITES, FULLERENES, RAW QUARTZ MINERALS - the group of deposits containing 5 min tons of high quality quartz good for manufacture of cut-glass and fibre-optical articles, is explored in details. There are also deposits of other kinds of non-traditional strategic mineral raw material in the Republic of Kazakstan - natural fillers, that can be used in the national economy of the country and bring considerable economic benefit: chrysotile-asbestos, amphibole-asbestos, talk, vollastonite, tremolite, actinolite, vermiculite, zeolite, etc

Characterization of Lignocellulosic Biomass as Raw Material for the Production of Porous Carbon-based Materials

Directory of Open Access Journals (Sweden)

Saptadi Darmawan

2016-02-01

Full Text Available Lignocellulosic biomass is a potential raw material that can be used in the synthesis (manufacture of porous carbon stuffs. The properties of such porous carbon products are affected by the species of the raw material and the manufacturing process, among other things. This paper scrutinizes the related characteristics of lignocellulosic raw materials that indicate potential for the production of porous carbon. Three species were used: pine (Pinus merkusii wood, mangium (Acacia mangium wood, and candlenut (Aleurites moluccana shells, representing softwoods, hardwoods, and non-wood stuffs, respectively. Analyses of their chemical compounds and proximate contents were carried out. Additionally, nano scale scrutiny of the lignocellulosic biomass was also conducted using the nano capable instruments, which consisted of SEM, EDS, XRD, FTIR, and DSC. Results revealed that pine wood had the most potential to produce porous carbon. Morphologically, pine wood afforded the best permeability, whereby at the structure of monoclinic cellulose crystals, there were cellulose-I(alpha structures, which contained less cellulose-I(beta structures. Furthermore, pine wood exhibited greater volatile matter content, as confirmed through the FTIR, which greatly assisted the forming of porosity inside its corresponding carbon.

Parasitic contamination of raw vegetables and fruits collected from selected local markets in Arba Minch town, Southern Ethiopia.

Science.gov (United States)

Bekele, Fitsum; Tefera, Tamirat; Biresaw, Gelila; Yohannes, Tsegaye

2017-03-07

One way that people get infected with intestinal parasites is through the consumption of contaminated vegetables and fruits. This study aimed at determining the prevalence and predictors of parasitic contamination of fruits and vegetables collected from four local markets in Arba Minch town, Southern Ethiopia. A cross-sectional study was conducted from 1 to 21 September 2014 to determine the level of parasitic contamination of fruits and vegetables sold in Arba Minch town. A total of 360 samples of different types of fruits and vegetables were soaked in physiological saline, followed by vigorous shaking with the aid of a mechanical shaker for 15 minutes and then examined using the sedimentation concentration technique. Out of the 360 samples examined, 196 (54.4%) were contaminated with at least one type of parasite. Ascaris lumbricoides (20.83%) was the most frequently detected parasite and Isospora belli (3.06%) was the least frequently detected one. It was also observed that decreased parasitic contamination was significantly associated with washing the products before displaying it for selling (P parasitic infections from the consumption of raw vegetables and fruits in Arba Minch, Ethiopia. The authors believe that an effort should be made by the relevant bodies to reduce the rate of contamination of products with medically important parasites by educating the vendors and the community.

Investigations of radioactivity of building raw and materials

International Nuclear Information System (INIS)

Zak, A.; Biernacka, M.; Jagielak, J.; Lipinski, P.

1993-01-01

In 1980, Ministry of Building and Building Materials Industry, the Central Laboratory for Radiological Protection (abbreviated as CLRP), Ministry of Health and Social Welfare have agreed to issue the compulsory regulation of performing the validation of investigations of building raw and materials. Methods of measurement, apparatus and method of evaluation of results of the investigations have been recommended for the whole country. The following two criteria of usefulness of a building material for housing and public building have been accepted, f 1 = 0.00027 S K + 0.0027 S Ra0 .0043 S Th ≤ 1 (this one limit exposition of the whole body to gamma radiation); f 2 = S Ra ≤ 185 Bq/kg (this one limits exposition of lung epithelium to progeny of radon 222 Rn exhaled from the building walls). The CLRP and Institute of Building Technology supervise over correctness (agreement with the regulations) of operation of laboratories in Departments of Building Industry and Energy, organize training of the personnel and collect results of the measurements. From 1980 till 1991, results of measurements of 6550 samples from 550 localities were collected in computer data base organized in CLRP. In this paper, results of examination of selected groups of building raw and materials have been presented. Annual average values of the qualification coefficients f 1 and f 2 have been also analyzed. (author). 7 refs, 13 figs, 2 tabs

Technological project of serpentine raw material milling from Dobšiná heaps

Directory of Open Access Journals (Sweden)

Alena Pietriková

2005-11-01

Full Text Available Serpentine heaps in the surrounding of Dobšiná are an old ecological problem of the city and at the same time a suitable material for the production of MgCl2 and SiO2. The technology of the production is based on the chemical processing of the raw material, which is preceded by the raw material preparation comprising of the mechanical and hydraulic sorting, milling and the magnetic separation operations.

Contamination of the cement raw material in a quarry site by seawater intrusion, Darica-Turkey

Science.gov (United States)

Camur, M. Zeki; Doyuran, Vedat

2008-02-01

The open pit mining nearby shoreline is planned to be extended into below sea level in order to use additional reserves of the cement raw material (marl). The raw material is currently contaminated by seawater intrusion below a depth of 20 m up to the distance of 90 m from shoreline. Seawater intrusion related contamination of the material used for the cement production was investigated by means of diffusion process for the future two below sea level mining scenarios covering 43 years of period. According to the results, chloride concentrations higher than the tolerable limit of a cement raw material would be present in the material about 10-25 cm inward from each discontinuity surface, controlling groundwater flow, located between 170 and 300 m landward from the shoreline at below sea level mining depths of 0-30 m. The estimations suggest that total amounts of dilution required for the contaminated raw material to reduce its concentration level to the tolerance limit with uncontaminated raw material are about 113- to 124-fold for scenario I (13 years of below sea level mining after 30 years of above sea level mining) and about 126- to 138-fold for scenario II (43 years of simultaneous above and below sea level minings).

To the question of peculiarities of thermal activation of natural siliceous raw material

Directory of Open Access Journals (Sweden)

Chumachenko Natalya

2017-01-01

Full Text Available The results of research of activity enhancement of natural siliceous raw material are given in the article. Fossil meal of Khotynetsky deposit, diatomite of Sharlovsky deposit, silica clay of Balasheika deposit were used as natural active mineral admixtures. The influence of heat-treating temperature and dispersion on activity of different types of siliceous raw material is studied. The increase of activity of fixation of Ca(OH2 in several times is traced after heat-treating at a certain temperature in the range from 100 to 800°C. The type of activity change is discovered. Explanation is given connected with the change of silica structure in the surface layer. Parameters of the highest activity are defined for every type of siliceous raw material.

Influence of raw material properties upon critical quality attributes of continuously produced granules and tablets

DEFF Research Database (Denmark)

Fonteyne, Margot; Wickström, Henrika; Peeters, Elisabeth

2014-01-01

over a range of raw material attributes, manufacturing process options and process parameters. This fits further into the Process Analytical Technology (PAT) and Quality by Design (QbD) framework. The present study evaluates the effect of variation in critical raw material properties on the critical......-Lactose-PVP (30-67.5-2.5%) was used as model formulation. Seven different grades of theophylline were granulated. Afterward, the obtained granules were tableted. Both the characteristics of granules and tablets were determined. The results show that differences in raw material properties both affect...... quality attributes of granules and tablets, produced by a continuous from-powder-to-tablet wet granulation line. The granulation process parameters were kept constant to examine the differences in the end product quality caused by the variability of the raw materials properties only. Theophylline...

Biotechnologies for critical raw material recovery from primary and secondary sources: R&D priorities and future perspectives

NARCIS (Netherlands)

Hennebel, T.; Boon, N.; Maes, S.; Lenz, M.

2015-01-01

Europe is confronted with an increasing supply risk of critical raw materials. These can be defined as materials of which the risks of supply shortage and their impacts on the economy are higher compared to most of other raw materials. Within the framework of the EU Innovation Partnership on raw

Buildings materials and raw materials as a source of exposition of population of the Slovak Republic

International Nuclear Information System (INIS)

Cabanekova, H.

2005-01-01

In this presentation author presents specific activities of potassium-40, radium-226, thorium-232 and equivalent of specific activity in some building materials and raw materials used at building-up of flats in the Slovak Republic

A framework for evaluating the accessibility of raw materials from end-of-life products and the Earth's crust.

Science.gov (United States)

Mueller, Sandra R; Wäger, Patrick A; Turner, David A; Shaw, Peter J; Williams, Ian D

2017-10-01

An increasing number of geochemically scarce metallic raw materials are entering into our lives via new technologies. A reversal of this trend is not foreseeable, leading to concerns regarding the security of their supply. However, the evaluation of raw material supply is currently hampered by inconsistent use of fundamental terminologies and incomplete assessment criteria. In this paper, we aim to establish a consistent framework for evaluating raw material supply from both anthropogenic and geological sources. A method for concept extraction was applied to evaluate systematically the use of fundamental terms in the evaluation of raw material supply. The results have shown that 'availability' is commonly used in raw material supply evaluations, whilst other researchers suggest that raw material supply should be evaluated based on 'accessibility'. It was revealed that 'accessibility' actually comprises two aspects: 'availability' and 'approachability'. Raw material 'approachability' has not previously been explicitly addressed at a system level. A novel, consistent framework for evaluating raw material supply was therefore developed. To demonstrate the application of the established framework, we evaluated the raw material supply of four rare earth element case studies. Three case studies are End-of-Life products (the anthroposphere) from Switzerland: (i) phosphors in fluorescent lamps, (i) permanent magnets in the drive motors of electric cars and (iii) fibre optic cable. The fourth case study source is the Earth's crust (the geosphere): Mount Weld deposit in Australia. The framework comprises a comprehensive evaluation of six components relating to raw material mining and processing: their geological knowledge, eligibility, technology, economic, societal and environmental impacts. Our results show that metals are not considered to be fully accessible in any of the case studies due to a lack of necessary technologies and potential societal and environmental

Current problems of raw fish material processing while manufacturing dried products

Directory of Open Access Journals (Sweden)

Yashonkov A. A.

2017-09-01

Full Text Available The substantiation for using techniques of fish raw material canning has been presented, raw fish being caught or farmed in aquaculture. The main problems in raw fish canning have been reviewed, including significant reduction in thermolabile vitamins in the ultimate product as compared with the raw material due to the thermal processing. Promising canning technique – vacuum drying – has been proposed. This technique makes possible to reduce the temperature of thermal processing down to 50…55 °С and significantly enlarge preservation of thermolabile vitamins from the raw fish. Sampling of raw materials, semi-finished products, finished products, including preparation for analysis has been conducted by standard methods. Disadvantages of this way have been found, it is low energy efficiency of the process. The way to intensify the vacuum drying of aquatic organisms has been proposed based on the method of preliminary pore-forming due to augmenting the area of moisture evaporation. The design of the pilot plant has been proposed in order to research the process of pore forming and vacuum drying. Target species for processing have been suggested. They are as follows: Azov goby (fillet for food products and Black Sea sprat for feeds. The recipes of the feed mixture for granulated floating food for trout have been developed. The results of the first series of the pilot research have been provided. The experiments have proved that preliminary pore forming immediately before vacuum drying makes possible to enlarge the surface area of moisture evaporation by 15…25 %. By processing photomicrographs of sections by means of a special software the authors have got the results demonstrating that when manufacturing dried products by pore forming and drying under pressure 10 kPa the pore take 35...38 % of the inner volume of the product and with drying under pressure 10 kPa – only 18...21 %, and when drying under the atmospheric pressure – 11...13 %.

The transfer of natural Rhodamine B contamination from raw paprika fruit to capsicum oleoresin during the extraction process.

Science.gov (United States)

Wu, Naiying; Gao, Wei; Lian, Yunhe; Du, Jingjing; Tie, Xiaowei

2017-12-15

Occurrence of Rhodamine B (RhB) contamination in paprika caused by agricultural materials during the vegetation process has been reported. It may transfer during the process of active compounds extraction, and eventually exist in final products. Herein, the re-distribution of RhB during the extraction process was assessed in terms of RhB contents, as well as mass, color value and capsaicinoids yield of each process. Results revealed that natural RhB contamination at 0.55-1.11µg/kg originated from raw paprika fruit then transferred with the extraction proceeded. About 95.5% of RhB was found in red oleoresin. After separation of red oleoresin, 91.6% of RhB was remained in capsicum oleoresin, only 3.7% in paprika red. These results were consistent with total capsaicinoids recovery of each product. The RhB levels in edible capsicum oleoresin in our present study at 0.01-0.34µg/kg did not exceed the legal limits established by the European Union. Copyright © 2017 Elsevier Ltd. All rights reserved.

Study on the technology of compound enzymatic hydrolysis of whole passion fruit

Science.gov (United States)

Yang, Yu-xia; Duan, Zhen-hua; Kang, Chao; Zhu, Xiang-hao; Li, Ding-jin

2017-12-01

Fresh Whole Passion Fruit was used as raw material, The enzymatic hydrolysis technology of Passion Fruit by Complex enzyme were studied, The effects of enzyme dosage, Enzyme ratio(cellulose: pectinase), pH, temperature and time on the hydrolysis were investigated by single-tests and orthogonal tests, the hydrolysis indicators of single-factor tests and orthogonal tests were juice yield. The optimal hydrolysis conditions of Passion Fruit by Complex enzyme were enzyme dosage 0.12%, Enzyme ratio 5:1, hydrolysis temperature 50°C, pH4.0 and time 3.5 h. Under such conditions, juice yield of Passion Fruit was 92.91%.

Biodiesel production using calcium manganese oxide as catalyst and different raw materials

International Nuclear Information System (INIS)

Dias, Joana Maia; Conceição Machado Alvim-Ferraz, Maria; Fonseca Almeida, Manuel; Méndez Díaz, José Diego; Sánchez Polo, Manuel; Rivera Utrilla, José

2013-01-01

Highlights: ► Biodiesel production using a calcium manganese oxide catalyst was studied. ► The active specie was Ca 0.9 Mn 0.1 O and its deactivation occurred by hydration. ► The studied catalyst presented lower activation temperature than CaO. ► Biodiesel production and quality using different raw materials is reported. ► Compared to the conventional process, biodiesel water content improved. - Abstract: The use of heterogeneous catalysts for biodiesel production aims to simplify the production process as well as to reduce purification costs and related environmental impacts. Calcium manganese oxide was recently identified by the authors as an interesting heterogeneous catalyst for biodiesel production from animal fat; however, the difference between this and other catalysts, the catalyst activation/deactivation mechanisms, its behaviour in the synthesis using different raw materials as well as the impacts of its use on product quality remained unclear. Therefore, the present work: (i) compared biodiesel production using calcium manganese oxide and other catalysts (CaO and NaOH); (ii) studied the reasons leading to activation/deactivation of the heterogeneous catalyst; (iii) analysed biodiesel heterogeneous synthesis using calcium manganese oxide and different raw materials (lard, waste frying oil and a mixture); and (iv) evaluated raw material and catalyst impact on the product quality. Considering the use of different catalysts, the results showed that, after 8 h of reaction, product purity was similar using the different catalysts, being 92.5 wt.% using both NaOH and calcium manganese oxide and 93.8 wt.% using CaO. The active species of the heterogeneous catalysts were CaO, in the case of calcinated calcium carbonate, and Ca 0.9 Mn 0.1 O, in the case of calcinated calcium manganese oxide. Because the deactivating species were different for both catalysts, the calcium manganese oxide required lower activation temperature, which should be an advantage

High-Temperature Release of SO2 from Calcined Cement Raw Materials

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of alternative fuels in the material inlet end of cement rotary kilns, local reducing conditions may occur and cause reductive decomposition of sulfates from calcined cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2...... concentration, which may cause deposit formation in the kiln system. In this study, the release of sulfur from calcined cement raw materials under both oxidizing and reducing conditions is investigated. The investigations include thermodynamic equilibrium calculations in the temperature interval of 800–1500 °C...... and experiments in a tube furnace reactor in the temperature interval of 900–1100 °C. The investigated conditions resemble actual conditions in the material inlet end of cement rotary kilns. It was found that the sulfates CaSO4, K2SO4, and Na2SO4 were all stable under oxidizing conditions but began to decompose...

The Content of Secondary Metabolites and Antioxidant Activity of Wild Strawberry Fruit (Fragaria vesca L.

Directory of Open Access Journals (Sweden)

Magdalena Dyduch-Siemińska

2015-01-01

Full Text Available Chemical analyses carried out in 2011–2013 aimed at evaluating the contents of flavonoids, free phenolic acids, tannins, anthocyanins, and antioxidant activity (% by means of DPPH radical neutralization ability in fresh and air-dried fruits of three wild strawberry cultivars. Examinations revealed differences in contents of biologically active substances determined in raw versus dried material depending on the cultivar. Mean concentrations of flavonoids and tannins were highest in raw fruits of “Baron von Solemacher” cv., which amounted to 1.244 mg·g−1 and 6.09%, respectively. Fresh fruits of “Regina” cv. were characterized by the highest average content of phenolic acids and anthocyanins: 4.987 mg·g−1 and 0.636 mg·100 g−1. The pattern of mean contents of biologically active substances analyzed in air-dried fruits was similar. Significant differences in abilities to neutralize the DPPH radical to diphenylpicrylhydrazine by extracts made of examined wild strawberry fruits were also indicated.

Globalization determinants of raw materials markets development

Directory of Open Access Journals (Sweden)

Olga Yatsenko

2013-02-01

Full Text Available The determinants of development of raw materials markets and the peculiarities of their formation in the terms of world economy globalization have been researched. The empirical base of research is the agricultural food market as one of the most important bases in the sphere of material production and provision of food security of the country. The important social and economic mission of the agricultural sector has been highlighted, along with the export competitiveness and import dependence of agricultural food products in the international trade. The imperative norms have been substantiated and conclusions have been drawn regarding the establishment of respective conditions for the operation of globally integrated markets in Ukraine.

Research and development programme of the EC in the field of raw materials 1982 to 1985

International Nuclear Information System (INIS)

Anon.

1982-01-01

Brussels: The EC Cabinet Council was presented a research and development programme in the field of raw materials for the years 1982 to 1985 which covers programmes already running and new actions as an overlapping raw material research programme of the EC. The new programme is divided up into 7 subprogrammes: I) metals and minerals (formerly: primary raw materials, II) uranium, III) ceramics, IV) wood as a renewable raw material, V) recycling of wastes (house and industry, VI) regaining of non-iron metals, VII) substitution. For the continuing of running actions and for beginning new projects in the 4 years plan, a total of 17 million ECU are to be allocated in the budget of the EC which will be used in cost sharing contracts or for coordinative projects. (orig./UA) [de

The use of foresight methods in strategic raw materials intelligence - an international review

Science.gov (United States)

Konrat Martins, Marco Antonio; Bodo, Balazs; Falck, Eberhard

2017-04-01

Foresight methods are systematic attempts to look into the longer term future of science, society, economy and technology. There is a range of tools and techniques that can be used individually or combined, most commonly classified into qualitative, quantitative or semi-quantitative methods, that follow an exploratory or normative approach. These tools can help to identify the longer term visions, orienting policy formulation and decisions, triggering actions, among other objectives. There is an identified lack of European strategic foresight knowledge in the raw materials domain. Since the European Raw Materials Initiative was launched in 2008, the EU has been attempting to overcome challenges related to the future access of non-energy and non-agricultural raw materials. In this context, the ongoing H2020 project, MICA (Mineral Intelligence Capacity Analysis, Grant Agreement No. 689648), has been launched to answer to stakeholders needs by consolidating relevant data, determining relevant methods and tools, and investigating Raw Materials Intelligence options for European mineral policy development, all tailored to fit under the umbrella of a European Raw Materials Intelligence Capacity Platform (EU-RMICP). As part of the MICA activities, an assessment of best practices and benchmarks of international raw materials foresight case studies has been carried out in order to review how EU and non-EU countries have employed foresight. A pool of 30 case studies has been collected and reviewed internationally, one third of which were selected for detailed assessment. These were classified according to their background and goals, in function of methods employed, and to the purpose of each method in the study: a total of 12 different methods were identified in these studies. For longer time frames, qualitative predictive methods such as Scenario Development have been repeatedly observed for mineral raw materials foresight studies. Substantial variations were observed in

Local Fruit Wastes as a Potential Source of Natural Antioxidant: An Overview

Science.gov (United States)

Ibrahim, U. K.; Kamarrudin, N.; Suzihaque, M. U. H.; Hashib, S. Abd

2017-06-01

Food industry in Malaysia which used fruits as one of the raw material such as the production of fruit juices, concentrates, jams and dried fruits, the main wastes of the production are the peel and the seed of the fruit. Nowadays, people have shown the interests to study the antioxidant content in the fruit wastes. All kind of fruits are believed to contain high amount of natural antioxidant properties such as vitamins, phenol, flavonoid and carotenoid. Thus, this paper presented the work done by researcher on antioxidant activity in the peel especially on local fruit such as mango peel, watermelon rind, banana peel and mangosteen pericarp. The review shows that the peel of the fruit is a good source of antioxidant and other bioactive compounds which have many benefits especially towards human health.

Stochastic Modelling and Self Tuning Control of a Continuous Cement Raw Material Mixing System

Directory of Open Access Journals (Sweden)

Hannu T. Toivonen

1980-01-01

Full Text Available The control of a continuously operating system for cement raw material mixing is studied. The purpose of the mixing system is to maintain a constant composition of the cement raw meal for the kiln despite variations of the raw material compositions. Experimental knowledge of the process dynamics and the characteristics of the various disturbances is used for deriving a stochastic model of the system. The optimal control strategy is then obtained as a minimum variance strategy. The control problem is finally solved using a self-tuning minimum variance regulator, and results from a successful implementation of the regulator are given.

Investigation situation of elimination germ in fruits and vegetables by ionizing irradiation

International Nuclear Information System (INIS)

Li Wenbing

2001-01-01

Raw vegetables and fruits carry pathogens. Ingestion of raw vegetables and fruits can cause outbreaks of illness. Ionizing radiation of fruits and vegetables cna deactivate pathogens. The usage of ionizing radiation in sterilization of fruits and vegetables is a promising technology that can be used to improve the safety of ready-to-eat fruit and vegetable

Prospect of trema orientalis as a pulping raw material in bangladesh

International Nuclear Information System (INIS)

Jahan, M.S.

2013-01-01

The pulp and paper industry in Bangladesh is looking for new raw materials with high productivity per hectare. Currently, bamboo and Gmelina arborea are the main pulping raw materials for the pulp and paper industry of the country. Trema orientalis is one of the fastest growing woods in the tropical region. This paper reviews the literature on the topic, in particular, related to the chemical, morphological and physical properties of T. orientalis and its suitability for pulping. In addition, the advantages and disadvantages of various ulping processes proposed in the literature were critically analyzed. It was concluded that T. orientalis is a potential pulp wood for the Bangladesh pulp and paper industry. (author)

Processing biofuels from farm raw materials - A systems study; Pelletering och brikettering av jordbruksraavaror - En systemstudie

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Daniel; Bernesson, Sven

2008-03-15

Use of processed biofuels (pellets, briquettes) has greatly increased in Sweden in recent decades, mainly to replace fossil fuels in large boilers, e.g. in coal powder boilers. More recently, the demand from private households and residential heating systems has also increased, mainly due to conversion from fossil heating oil. This increased interest in pellets and briquettes for heating is beginning to cause a shortage of the traditional raw materials, sawdust and wood shavings, and therefore attention is turning to using a variety of agricultural products as raw material. Such raw materials include cultivated energy crops and wastes and by-products from agriculture. This study describes the typical systems currently used for production of pellets and briquettes and investigates the possibility of using energy crops (Salix, reed canary-grass and hemp) and various wastes and by-products from processing of farm products (straw, cereal screenings, rape-seed meal and distiller's waste) as raw materials. Previous experiences of pelletizing and briquetting of these raw materials are reviewed in order to comprehensively identify possible combustion problems that may occur. On the basis of the results obtained, scenarios for possible production systems in a five-year perspective are presented and the costs and energy demands for these systems calculated. These future scenarios include large scale plants and micro-scale plants, as well as static and mobile equipment. The five main conclusions from the study are: - The farm raw materials of greatest interest for large-scale production are pelleted Salix and reed canary-grass. They have competitive prices and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelletizing factories in Sweden. - Straw has low production costs but can cause serious ash-related problems. Hemp has too high production costs to be of commercial interest, while distiller's waste and rape-seed meal currently

Method of thermal reprocessing of hydrocarbon raw material

Energy Technology Data Exchange (ETDEWEB)

Feygin, Ye.A.; Bakhshiyan, Ts.A.; Barashkov, R.Ya.; Kazhdan, A.Z.; Raud, E.A.; Umanchik, N.P.

1979-09-30

In the method of thermal reprocessing of hydrocarbon raw material, to raise the efficiency of the process the heat exchange is done using a heat carrier in the form of a melt of metals or their salts, circulating in a closed system with a forced heating source in sequence through the pyrolysis zone, cooling zone, and heating zone. For example, the benzine fraction with initial boiling temperatures of 80-186 degrees C, together with steam, in the amount of 20% at 20 degrees C and pressure of 2 atmospheres, goes to the heating zone. Liquid Li goes there from the cooling zone through a closed circuit at 749 degrees C. The benzine, evaporated and heated to 300 degrees C, together with the melt, go to the pyrolysis zone, where the benzine is heated through the wall by the liquid Li coming from the heat carrier heating zone at 1000 degrees C. From the pyrolysis zone, the products, containing 41% C/sub 2/H/sub 4/, 15% C/sub 3/H/sub 6/ and 21% heavy fractions, go with the melt at 900 degrees C to the cooling zone, where they are cooled through the wall to 400 degrees C by the circulating liquid Li. The Li temperature at the entry into the cooling zone is 350 degrees C. The degree of raw material conversion is over 98%; the melt/raw material weight ratio is 0.2. Using this method enables a reduction in the pyrolysis zone from 80 to 8 m and the cooling zone area from 13 to 0.6 m/sup 2/ compared with the existing one, and transition from a multiple-tube cooling zone design to a tube one. The volume of the furnace unit is reduced from 500 to 10 m/sup 3/; the C/sub 2/H/sub 4/ yield is increased from 26-28 to 40-42%.

Prospects of rice straw as a raw material for paper making.

Science.gov (United States)

Kaur, Daljeet; Bhardwaj, Nishi Kant; Lohchab, Rajesh Kumar

2017-02-01

Pulp and paper mills are indispensable for any nation as far as the growth of the nation is concerned. Due to fast growth in population, urbanization and industrialization, the demand and consumption of paper has increased tremendously. These put high load on our natural resources and force the industry to look for alternative raw material. Rice straw is a lignocellulosic material abundantly available in wood short countries like China, India, Bangladesh, etc. and can be used as raw material for this industry. Open burning of rice straw releases noxious green house gases to the air and poses serious threats to global air chemistry and human health. So, it is a dual benefit option (for farmers and industries) to use rice straw as a raw material in pulp and paper industry. Organosolv pulping using acids are the prominent choices of researchers to convert this residue into valuable pulp but in developed countries only. Developing world favours the soda and soda-AQ processes as these are economical. As a virtue of less lignin content in comparison to wood, rice straw requires less harsh conditions for cooking and can be easily pulped. Bleaching is a crucial step of paper making but also responsible for causing water pollution. Many studies revealed that during the process more than 500 chlorinated compounds are released that are highly toxic, bioaccumulative and carcinogenic in nature. Most of the industries over the globe switch on to the elemental chlorine free short sequence bleaching methods using chlorine dioxide, hypochlorite and hydrogen peroxide. This paper presented the effective need of ecofriendly, economically reliable pulping and bleaching sequences in case of rice straw to eliminate the problems of chlorinated compounds in wastewater of paper mills. Such approach of using waste as a raw material with its environmentally safe processing for making paper can prove to be valuable towards sustainable growth. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sustainability evaluation of essential critical raw materials: cobalt, niobium, tungsten and rare earth elements

Science.gov (United States)

Tkaczyk, A. H.; Bartl, A.; Amato, A.; Lapkovskis, V.; Petranikova, M.

2018-05-01

The criticality of raw materials has become an important issue in recent years. As the supply of certain raw materials is essential for technologically-advanced economies, the European Commission and other international counterparts have started several initiatives to secure reliable and unhindered access to raw materials. Such efforts include the EU Raw Materials Initiative, European Innovation Partnership on Raw Materials, US Critical Materials Institute, and others. In this paper, the authors present a multi-faceted and multi-national review of the essentials for the critical raw materials (CRMs) Co, Nb, W, and rare earth elements (REEs). The selected CRMs are of specific interest as they are considered relevant for emerging technologies and will thus continue to be of increasing major economic importance. This paper presents a ‘sustainability evaluation’ for each element, including essential data about markets, applications and recycling, and possibilities for substitution have been summarized and analysed. All the presented elements are vital for the advanced materials and processes upon which modern societies rely. These elements exhibit superior importance in ‘green’ applications and products subject to severe conditions. The annual production quantities are quite low compared to common industrial metals. Of the considered CRMs, only Co and REE gross production exceed 100 000 t. At the same time, the prices are quite high, with W and Nb being in the range of 60 USD kg‑1 and some rare earth compounds costing almost 4000 USD kg‑1. Despite valiant effort, in practice some of the considered elements are de facto irreplaceable for many specialized applications, at today’s technological level. Often, substitution causes a significant loss of quality and performance. Furthermore, possible candidates for substitution may be critical themselves or available in considerably low quantities. It can be concluded that one preferred approach for the

EFFICIENCY OF RAW MATERIAL INVENTORIES IN IMPROVING SUPPLY CHAIN PERFORMANCE of CV. FIVA FOOD

Directory of Open Access Journals (Sweden)

Artadi Nugraha

2016-01-01

Full Text Available The production and number of processed food industries have slightly increased; as a result, the companies must compete to maximize their profits by conducting their efficient production process. CV. Fiva Food is one of the companies in the field of processed foods, especially in processed meat that has implemented supply chain management. It is necessary for the company to take measurements of its performance and efficiency for the entire supply chain such as procurement of raw materials. The purposes of this study were to analyze the performance of the company's supply chain and determine the most efficient  method of procurement for its raw materials as well as and to provide recommendations for the company to improve its performance of entire supply chain. This study used SCOR in analyzing the performance of supply chain and EOQ and POQ method to be compared with the method that the company uses to determine which method of procurement for raw materials is the most efficient one. The result showed that based on the matrix, the company's performance is unfavorable when it was compared to the benchmark performance of inventory days of supply. In addition, this study showed that the POQ method produces the lowest total inventory cost with savings of Rp6.647.015 for raw materials of MDM whereas EOQ method produced the lowest total inventory cost with savings of Rp222.153,78 for raw materials of FQ85CL. Keywords: performance suppy chain, SCOR, fiva food, EOQ, POQ

Use of alternative raw materials for yoghurt production | Farinde ...

African Journals Online (AJOL)

Soymilk and maize steep water were used as alternative raw materials to cow milk and commercial starter, respectively, for production of yoghurt. The cow milk used was both Fresh milk and dried powdered milk (DANO). The cost of production of the yoghurt samples as well as their chemical, microbial and organoleptic ...

Radioactivity and associated radiation hazards in ceramic raw materials and end products.

Science.gov (United States)

Viruthagiri, G; Rajamannan, B; Suresh Jawahar, K

2013-12-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of (226)Ra, (232)Th and (40)K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants.

Radioactivity and associated radiation hazards in ceramic raw materials and end products

International Nuclear Information System (INIS)

Viruthagiri, G.; Rajamannan, B.; Suresh Jawahar, K.

2013-01-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of 226 Ra, 232 Th and 40 K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants. (authors)

2.4. The kinetics of hydrochloric-acid decomposition of calcined concentrate of boron raw material of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

2015-01-01

Present article is devoted to kinetics of hydrochloric-acid decomposition of calcined concentrate of boron raw material of Ak-Arkhar Deposit. The experimental data of dependence of hydrochloric-acid decomposition of calcined boron raw material for boron oxide extraction on temperature (20-80 deg C) and process duration (15-60 min) were considered. It was defined that at temperature increasing the boron oxide extraction from borosilicate raw material increases from 24.1 till 86.8%. The constants of decomposition rate of boron raw material were calculated.

Review of scientific Research results in identification of plant raw materials in food products

OpenAIRE

GOLUBTSOVA YU. V.

2016-01-01

Currently, the science-based capabilities have been generated to develop and test various identification methods of food products and reveal adulteration using advanced technique and processes. This article reviews researches and developments to identify the plant raw materials in food products based on morphological, anatomic, physical and chemical test methods and the latest DNA-technologies. Review of physical, chemical, anatomic and morphological test methods to identify raw materials bot...

Prospects for development of hydrocarbon raw materials resources reproduction

Science.gov (United States)

Vertakova, Y. V.; Babich, T. N.; Polozhentseva, Y. S.; Zvyagintsev, G. L.

2017-10-01

The article presents data on the influence of factors in the field of innovative technology of thermocatalytic depolymerization of solid household wastes (SHW) on the efficiency and prospects for the development of technogenic hydrocarbon raw materials resource reproduction. Process thermodynamics, reactions kinetics, the mechanism of thermolysis of secondary polymers in organic solvents have been studied by means of laboratory experiments. It is shown that different morphological groups of wastes dissolve practically at the same rate at temperatures of 250-310°C. A homogeneous product is formed in the liquid phase; the spread of values for the elements lies in the interval of 1.5-4.5 %; technological requirements of the stages of formation of boiler fuels are satisfied. Using the principles of patent analysis, new techniques of processing household waste components are proposed. The basics of energy-efficient and energy-saving processes of technogenic hydrocarbon raw materials resource reproduction have been laid. The possibility of increasing the production payback and intensification is shown. Ecological and demographic safety for population and technical and economic benefits from SHW processing are achieved.

Mechanochemical modification of the composition and structure of plant raw materials to control the combustion of alternative fuel

Directory of Open Access Journals (Sweden)

Bychkov Aleksey

2017-01-01

Full Text Available The possibilities of mechanochemistry in processing of renewable lignocellulose raw material into solid kinds of biofuel are demonstrated in this work. A review of lignocellulose raw materials promising for our country is presented. These raw materials include wastes from agriculture and forestry, and the biomass of rapidly growing plants. The physicochemical properties of lignocellulose materials with different delignification degrees were modeled with the help of the artificial mixtures of plant raw material with purified cellulose and lignin. The data illustrating the effect of disperse state and lignin content on the reactivity of the material in subsequent combustion are presented. The tests at the combustion bench with the thermal power up to 5 MW allowed determining the optimal combustion parameters for the obtained biofuel in the autothermal mode.

Reuse and recovery of raw materials: Towards the achievement of a resource-efficient society

International Nuclear Information System (INIS)

Brunori, Claudia; Cutaia, Laura; Norabito, Roberto

2015-01-01

Resource efficiency plays a key role in the transition from a linear to a circular economy system. During the last few decades a rapid growth in the number of materials used across complex products has occurred. Given the high economic importance of critical raw materials combined with relatively high supply risk, securing reliable and undistorted access of certain raw materials is of growing concern across the globe. Development of eco-innovative approaches devoted to closing the loop of resources is strongly needed, allowing the connection between production cycles and their territory.

Energies and raw materials. Letter n.28

International Nuclear Information System (INIS)

2007-01-01

This letter of the DGEMP (General Direction of the Energy and the Raw Materials) deals with the following four main topics: the main recommendations of the final report of the working Group ''Factor 4'' concerning the energy policy; the energy conservation certificates as a tool of the energy control with their implication in the residential and ternary sector; the increase of the solar water heaters and heat pumps sales thanks to the tax credits; the California example facing the climatic change and the energy policy. (A.L.B.)

Cellulosic pulps of cereal straws as raw material for the manufacture of ecological packaging

OpenAIRE

Vargas González, Fátima; González, Zoilo; Sánchez, Rafael; Jiménez, Luis; Rodríguez Pascual, Alejandro

2012-01-01

The aim of this work was to study the potential application of four types of cereal straws: oats, maize, rapeseed, and barley, in order to obtain cellulose pulp through the Specel® process for use in the manufacture of 100% biodegradable and ecological packaging. Raw materials were chemically characterized to determine alcohol-extractives, ash, lignin, holocellulose, and α-cellulose. Cellulosic pulps obtained from raw materials were characterized to determine yield, Kappa number, and viscosit...

Construction raw materials policy and supply practices in Northwestern Europe

NARCIS (Netherlands)

Meulen, M.J. van der; Koopmans, T.P.F.; Pietersen, H.S.

2003-01-01

The present contribution is an inventory of the construction raw materials policy and supply practices in The Netherlands, Belgium, North Rhine-Westphalia, Lower Saxony, Great Britain, Norway and Denmark. The work has been commissioned by the Dutch government in order to benchmark its domestic

Analysis of Mechanical Properties of Fabrics of Different Raw Material

Directory of Open Access Journals (Sweden)

Aušra ADOMAITIENĖ

2011-07-01

Full Text Available The study analyzes dependence of mechanical properties (breaking force, elongation at break, static friction force and static friction coefficient on integrated fabric structure factor j and raw material density r, among the fabrics of different raw material (cotton, wool, polypropylene, polyester and polyacrylnitrile and woven in different conditions. The received results demonstrate that sometimes strong dependences exist (wool, polypropylene and polyacrylnitrile, whereas in some cases (cotton and polyester there is no correlation. It was also discovered that the breaking force and elongation at break in the direction of weft increase, when fabric structure becomes more rigid. In the meantime variations of the curves in the direction of warp are insignificant. Regarding static friction force and static friction coefficient (found in two cases, when fabrics were rubbing against leather and materials, it was discovered that consistency of the curves is irregular, i. e. they either increase or decrease, when integrated fabric structure factor j growth. It was also identified that some dependences are not strong and relationship between explored and analyzed factors does not exist. Variation of all these mechanical properties with respect to material density r enables to conclude that increase of material density r results in poor dependences or they are whatsoever non-existent.http://dx.doi.org/10.5755/j01.ms.17.2.487

An integrated production-inventory model for food products adopting a general raw material procurement policy

Science.gov (United States)

Fauza, G.; Prasetyo, H.; Amanto, B. S.

2018-05-01

Studies on an integrated production-inventory model for deteriorating items have been done extensively. Most of the studies define deterioration as physical depletion of some inventories over time. This definition may not represent the deterioration characteristics of food products. The quality of food production decreases over time while the quantity remains the same. Further, in the existing models, the raw material is replenished several times (or at least once) within one production cycle. In food industries, however, a food company, for several reasons (e.g., the seasonal raw materials, discounted price, etc.) sometimes will get more benefit if it orders raw materials in a large quantity. Considering this fact, this research, therefore, is aimed at developing a more representative inventory model by (i) considering the quality losses in food and (ii) adopting a general raw material procurement policy. A mathematical model is established to represent the proposed policy in which the total profit of the system is the objective function. To evaluate the performance of the model, a numerical test was conducted. The numerical test indicates that the developed model has better performance, i.e., the total profit is 2.3% higher compared to the existing model.

Irradiation as an alternative environment friendly method for microbiological decontamination of herbal raw material

International Nuclear Information System (INIS)

Gorecki, P.; Kedzia, B.; Migdal, W.; Owczarczyk, H.B.

1998-01-01

Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the product in order to act effectively against all the microorganisms present and must not reduce the sensory and technological qualities of the commodities. In the paper, the results of comparative investigations on the microbiological decontamination of herbal raw materials by chemical (ethylene oxide, methyl bromide) and physical method (irradiation) are presented. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods have been recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process

Occupational radiation protection in the mining and processing of raw materials

International Nuclear Information System (INIS)

2004-01-01

The mining and processing of uranium ore, thorium ore and other raw materials containing natural radionuclides are carried out in a number of Member States. There is a clear need to update the guidance on the radiation protection of the workers involved, and this Safety Guide provides such updated guidance. Material from two previous publications has been adapted for inclusion in this Safety Guide. These previous publications - Radiation Monitoring in the Mining and Milling of Radioactive Ores (Safety Series No. 95) and Radiation Protection of Workers in the Mining and Milling of Radioactive Ores (Safety Series No. 26, hereby superseded) - dealt principally with activities involving uranium ore and thorium ore. Activity concentrations of naturally occurring radionuclides are elevated in other mineral deposits such as heavy mineral sands and phosphate rock. Furthermore, high radon levels may be found in mines, irrespective of the activity concentrations of natural radionuclides in the raw material being extracted. In recognition of these circumstances, this Safety Guide is intended to apply also to the mining and processing of any raw material for which radiation protection measures need to be considered. The IAEA Safety Fundamentals publication on Radiation Protection and the Safety of Radiation Sources presents the principles, concepts and objectives of protection and safety. Safety requirements based on the objectives and principles specified in these Safety Fundamentals, including requirements for the protection of workers exposed to ionizing radiation, are established in the International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources (the Basic Safety Standards or Bss). These requirements also reflect the recommendations of the International Commission on Radiological Protection (ICRP). Safety Guides provide recommendations on the basis of international experience on the fulfilment of the requirements

New technologies and raw materials for iron and steel making

Energy Technology Data Exchange (ETDEWEB)

Holappa, L. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Metallurgy

1998-07-01

The current steelmaking is still mainly based on two alternatives routes. The first one is ore based production route via reduction in blast furnaces (BF) to produce carbon-rich hot metal which is then oxidised in basic oxygen converter process (BOF) to crude steel, then refined and alloyed in several secondary (ladle) metallurgical operations to its final composition, further followed by continuous casting and rolling operations. The second main steelmaking route starts from steel scrap as the main raw material, melting of scrap in electric furnaces to crude steel, the subsequent stages being corresponding to those in ore based steelmaking. Both these processes represent well-established and highly developed technologies. However, they have some drawbacks. Blast furnace process needs sinter or pellets and coke as its raw materials. That means erection of large integrates with high investment costs in the production units themselves as well as to avoid severe environmental issues. Scrap-based steelmaking is ideal from the viewpoint of recycling, but it is limited by the scrap availability and quality problems encountered by the noticeable metallic impurities in purchase scrap. Direct reduction of iron ore in solid state to produce direct reduced iron (DRI) has its roots in the early ironmaking history but was firstly commercialised on a modern concept at the end of the 1960's when the first Midrex installation was run into operation. Most of the DR-processes utilise natural gas as the reducing agent but also some processes utilising coal have been introduced and are used in industrial scale. The oil crises in the 1970's slowed down the progress of DRI production but during the last 15 years the production has steadily grown being nowadays about 35 Mton/year. That corresponds to roughly 10 pct of the total solid material input into the world steel production. No doubt, the growth will continue in the near future as well. Quite recently, a new process

Analysis of waste coal from the enterprises of Kemerovo region as raw materials for production of ceramic materials

Science.gov (United States)

Stolboushkin, A. Yu; Akst, D. V.; Fomina, O. A.; Ivanov, A. I.; Syromyasov, V. A.

2017-09-01

The analysis of waste coal from mining enterprises of Kemerovo region as raw materials for production of building ceramics is given. The results of studies of material, chemical and mineralogical compositions of waste coal from Abashevskaya processing plant (Novokuznetsk) are presented. It was established that the chemical composition of waste coal refers to aluminosilicate raw materials with a high content of alumina and coloring oxides, the residual carbon content in the wastes is 12-25 %. According to the granulometric composition the waste coal is basically a sandy-dusty fraction with a small amount of clay particles (1-3 %). Additional grinding of coal waste and the introduction of a clay additive in an amount of up to 30 % are recommended. The results of the study of the mineral composition of waste coal are presented. Clay minerals are represented in the descending order by hydromuscovite, montmorillonite and kaolinite, minerals-impurities consist of quartz, feldspar fine-dispersed carbonates. The results of the investigation of ceramic-technological properties of waste coal, which belong to the group of moderately plastic low-melting raw materials, are given. As a result of a comprehensive study it was been established that with chemical, granulometric and mineralogical compositions waste coal with the reduced residual carbon can be used in the production of ceramic bricks.

The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

Science.gov (United States)

Halavska, L.; Batrak, O.

2016-07-01

A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

Raw materials for pellets; Rohstoffe fuer Pellets

Energy Technology Data Exchange (ETDEWEB)

Neumann, H.

2008-01-15

In order to keep the pellet prices stable, producers look for new raw materials. Sawdust as a former basis also competes with the manufacturers of chip boards and paper. Three classes of quality are discussed by the pellet manufacturers: (a) the DINplus pellet as a premium segment for which high-quality sawdust are used; (b) a wood pellet from natural wood with varying quality for the utilization in larger plants with filters; (c) the inexpensive industrial wood pellet which deviates from the DINplus commodity regarding to the ingredients and form and could be fired in larger power stations.

Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

Energy Technology Data Exchange (ETDEWEB)

Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P. [All-Russia Research Institute of Preservation Technology (Russian Federation); Egorkin, A. V.; Chasovskikh, A. V. [Research Institute of Technical Physics and Automation (Russian Federation); Pavlov, Yu. S., E-mail: rad05@bk.ru [Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences (Russian Federation); Prokopenko, A. V., E-mail: pav14@mail.ru [National Research Nuclear University (Moscow Engineering Physics Institute) (Russian Federation); Strokova, N. E. [Moscow State University (Russian Federation); Artem’ev, S. A. [Russian Research Institute of Baking Industry (Russian Federation); Polyakova, S. P. [Russian Research Institute of Confectionery Industry (Russian Federation)

2016-12-15

The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

Enhancement of efficiency of storage and processing of food raw materials using radiation technologies

International Nuclear Information System (INIS)

Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P.; Egorkin, A. V.; Chasovskikh, A. V.; Pavlov, Yu. S.; Prokopenko, A. V.; Strokova, N. E.; Artem’ev, S. A.; Polyakova, S. P.

2016-01-01

The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.

Mining of Radioactive Raw Materials as an Origin of the Nuclear Fuel Chain

Directory of Open Access Journals (Sweden)

Bedřich Michálek

2007-01-01

Full Text Available The mining of radioactive raw materials may be considered as an origin of the nuclear fuel chain and thus determines the amount of radioactive wastes which have to be stored safety in the final stage of the fuel chain. The paper informs about the existing trends in mining of radioactive raw materials in the world, provides an overview of development in mining in the Czech Republic and of possibilities of future exploiting some uranium deposits. It points a possibility of non-traditional obtaining uranium from mine waters from underground uranium mines closed and flooded earlier.

Radiation decontamination (hygienisation) of cosmetic raw materials and products

International Nuclear Information System (INIS)

Malec-Czechowska, K.; Migdal, W.; Owczarczyk, H.B.

1998-01-01

Microbiological purity of cosmetics is a problem of today because of growing hygienic requirements to these products. The demand for high hygienic purity from one side and the limitation in the use of conservants to cosmetics from the other side stimulate the research activity, the aim of which is to satisfy present requirements in this field. The application of radiation decontamination (hygienisation) seems to be one of solutions. In present report were present the results of the study on the effect of electron beam irradiation on microbial contamination of selected cosmetics and some raw materials used in cosmetic industry. Radiation doses applied were not higher than 6.0 kGy. The level of microbial contamination in both unirradiated and irradiated samples was determined by applying the standard microbiological methods. In addition, the quality and usefulness of irradiated cosmetics were examined by methods used in cosmetic industry. The results obtained show conclusively that radiation treatment can be successfully used for the decontamination (hygienisation) of cosmetics and some raw materials used in their production, without changing the quality and the usefulness of the product released. (author)

Yeasts and lactic acid bacteria microbiota from masau (Ziziphus mauritiana) fruits and their fermented fruit pulp in Zimbabwe

NARCIS (Netherlands)

Nyanga, L.K.; Nout, M.J.R.; Gadaga, T.H.; Theelen, R.M.C.; Boekhout, T.; Zwietering, M.H.

2007-01-01

Masau are Zimbabwean wild fruits, which are usually eaten raw and/ or processed into products such as porridge, traditional cakes, mahewu and jam. Yeasts, yeast-like fungi, and lactic acid bacteria present on the unripe, ripe and dried fruits, and in the fermented masau fruits collected from

Characterization of raw materials to obtain the mass for white ware, using waste glass

International Nuclear Information System (INIS)

Cavalcanti, M.S.L.; Porto, V.S.; Meneses, R.L; Albuquerque, A.V.; Guedes, B.F.R.; Morais, C.R.S.; Santana, L.N.L.

2009-01-01

A major problem faced in the post modern society is the huge amount of glass, accumulated in landfills cities. The glass material is one hundred percent recyclable and has the property to act as fluxes as well as feldspar. Given this premise, this study aimed to characterize materials - raw materials and waste glass regional plan for development of ceramic bodies with the similar behavior produced industrially, using shards of glass to partially replace the feldspar. The materials - raw materials used were clay, ball clay, kaolin, quartz, feldspar and shard of glass, being characterized by the techniques: chemical analysis, size analysis, differential thermal analysis vibrational spectroscopy in the infrared region, the Ray-Diffraction X and scanning electron microscopy. The results showed that the waste had higher rates of vitreous oxides fluxes and similar. (author)

Quality assessment of baby food made of different pre-processed organic raw materials under industrial processing conditions.

Science.gov (United States)

Seidel, Kathrin; Kahl, Johannes; Paoletti, Flavio; Birlouez, Ines; Busscher, Nicolaas; Kretzschmar, Ursula; Särkkä-Tirkkonen, Marjo; Seljåsen, Randi; Sinesio, Fiorella; Torp, Torfinn; Baiamonte, Irene

2015-02-01

The market for processed food is rapidly growing. The industry needs methods for "processing with care" leading to high quality products in order to meet consumers' expectations. Processing influences the quality of the finished product through various factors. In carrot baby food, these are the raw material, the pre-processing and storage treatments as well as the processing conditions. In this study, a quality assessment was performed on baby food made from different pre-processed raw materials. The experiments were carried out under industrial conditions using fresh, frozen and stored organic carrots as raw material. Statistically significant differences were found for sensory attributes among the three autoclaved puree samples (e.g. overall odour F = 90.72, p processed from frozen carrots show increased moisture content and decrease of several chemical constituents. Biocrystallization identified changes between replications of the cooking. Pre-treatment of raw material has a significant influence on the final quality of the baby food.

THE PAPER CHARACTERISTICS FROM COMBINATION OF RICE HUSKS AND EMPTY FRUIT BUNCHES

OpenAIRE

Yuli Ristianingsih; Hero Islami; Muhammad Sarwani

2017-01-01

Abstract- Rice husk and empty fruit bunches are agricultural and plantation wastes which have fiber cellulose and hemicellulose, it can be converted to pulp and paper. This research aims to study the effect of NaOH concentration (2, 4, 6 and 8% w/v) and raw material composition to pulp yield and to study characteristics of the paper combination of rice husk and empty fruit bunches using soda process based on SEM and XRD analysis. This research using soda process because it is suitable for no...

Energies and raw material. Annual report; Energies et matieres premieres. Rapport annuel

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The annual report of the french General Direction of the Energy and the Raw Material (DGEMP) deals with the energy policy. The following subjects are analysed: the french program of fight against the global warming; the biogas; the radioactive wastes management program; the french nuclear industry re-organization; Tchernobyl; the electric power and gas public service; the risk prevention concerning the electric power production; the international Gaz De France protocol; the closing of the Ales mine; the cooperation ELF and TOTAL; the french para-petroleum industry; the raw material prices; the french mining situation; the french energy policy audit by the AIE; the energy accidents of december. The DGEMP organization chart with contacts and the publications are also included. (A.L.B.)

Raw materials in Africa and aspects of their utilisation; Rohstoffe in Afrika und Aspekte zu ihrer Nutzung

Energy Technology Data Exchange (ETDEWEB)

Leonhardt, Joachim [Dr. Leonhardt Consulting, Essen (Germany)

2011-03-15

Consideration of raw materials in Africa and aspects of their utilisation refers not only to raw materials and their use, but also quite importantly to the prevailing situation in Africa itself and with regard to the population, the economic situation and also the commitment of other countries. (orig.)

STUDY OF ACAROID MITES POLLUTION IN STORED FRUIT-DERIVED CHINESE MEDICINAL MATERIALS.

Science.gov (United States)

Xu, Li-fa; Li, He-xia; Xu, Peng-fei; Xu, Hai-feng; Li, Chao-pin

2015-08-01

to investigate the species and breeding density of acaroid mites in stored fruit-derived Chinese medicinal materials in Anhui province. samples of stored fruit-derived Chinese medicinal materials were collected from 30 herb stores and storehouses in 17 Anhui cities, where the breeding acaroids mites were detected. 20 species of acaroids mites were found in 33 samples, belonging to 15 genus, 5 families of the acaridae respectively, among which T. putrescentiae, A. farinae, C. lactis, and C. berlesei are predominant species. stored fruit-derived Chinese medicinal materials in Anhui areas suffer from serious acaroid mites pollution. Therefore, proactive measures should be taken to control acaroid mites from breeding in an effort to reduce the harm on medicinal materials. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

1996 Progress report on energies and raw materials; 1996 rapport d`activite energies et matieres premieres

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The 1996 annual progress report, from the French Department of Energy, reviews the key points of the French policy for energy and raw materials: competitiveness, environmental protection, long term supply safety, and public service. 1996 was marked by positive results for the French energy industry, difficulties for the oil refining industry, and a new impetus for renewable energies. Five surveys are presented: nuclear safety in Eastern Europe, the european directive on electric power domestic market, evolution of the oil market, conditions of refining in France, and restructuring of the Mine bureau (BRGM). 40 prominent facts are briefly reviewed, concerning sustainable energy development, nuclear energy, electric power and gas, coal, oil products, raw materials. Diagrams on energy and raw materials are also included

1996 Progress report on energies and raw materials; 1996 rapport d`activite energies et matieres premieres

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

The 1996 annual progress report, from the French Department of Energy, reviews the key points of the French policy for energy and raw materials: competitiveness, environmental protection, long term supply safety, and public service. 1996 was marked by positive results for the French energy industry, difficulties for the oil refining industry, and a new impetus for renewable energies. Five surveys are presented: nuclear safety in Eastern Europe, the european directive on electric power domestic market, evolution of the oil market, conditions of refining in France, and restructuring of the Mine bureau (BRGM). 40 prominent facts are briefly reviewed, concerning sustainable energy development, nuclear energy, electric power and gas, coal, oil products, raw materials. Diagrams on energy and raw materials are also included

Colorimetric determination of a paracetamole in raw material and in pharmaceutical dosage forms

International Nuclear Information System (INIS)

Usifoh, C.O; Adelusi, S.A.; Adebambo, R.F.

2002-01-01

A rapid, accurate and simple method is proposed for the determination of p-acetaminophen (paracetamole) in raw material, tablets and syrups. The method is based on measuring the intensity of the yellow color that developed when acute acetaminophen is allowed to react with p-dimethylaminobenzaldehyde in 2M HCl after heating. The color which absorbs in the visible region of gamma 450 nm is stable for several hours and the intensity is directly proportional to the concentration of the drug, that is, Beer lambert law is obeyed. The method can be used to analyse paracetamole in raw material and in pharmaceutical dosage forms. (author)

Aerospace Fuels From Nonpetroleum Raw Materials

Science.gov (United States)

Palaszewski, Bryan A.; Hepp, Aloysius F.; Kulis, Michael J.; Jaworske, Donald A.

2013-01-01

Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer-Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA Glenn Research Center is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term green relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Another issue of great concern is minimizing impurities in the product stream(s), especially those that are potential health risks and/or could degrade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered

Sensory properties of marinated herring (Clupea harengus) processed from raw material from commercial landings

DEFF Research Database (Denmark)

Nielsen, Durita; Hyldig, Grethe; Nielsen, Jette

2005-01-01

Sensory properties of marinated herring processed from raw material from Danish commercial catches were described and related to fishing season and biological, chemical and functional properties. Herring was caught on five cruises and stored on board in tanks or ice. The sensory profile of marina......Sensory properties of marinated herring processed from raw material from Danish commercial catches were described and related to fishing season and biological, chemical and functional properties. Herring was caught on five cruises and stored on board in tanks or ice. The sensory profile...

From raw material to dish: pasta quality step by step.

Science.gov (United States)

Sicignano, Angelo; Di Monaco, Rossella; Masi, Paolo; Cavella, Silvana

2015-10-01

Pasta is a traditional Italian cereal-based food that is popular worldwide because of its convenience, versatility, sensory and nutritional value. The aim of this review is to present a step-by-step guide to facilitate the understanding of the most important events that can affect pasta characteristics, directing the reader to the appropriate production steps. Owing to its unique flavor, color, composition and rheological properties, durum wheat semolina is the best raw material for pasta production. Although pasta is traditionally made from only two ingredients, sensory quality and chemical/physical characteristics of the final product may vary greatly. Starting from the same ingredients, there are a lot of different events in each step of pasta production that can result in the development of varieties of pasta with different characteristics. In particular, numerous studies have demonstrated the importance of temperature and humidity conditions of the pasta drying operation as well as the significance of the choice of raw material and operating conditions on pasta quality. © 2015 Society of Chemical Industry.

Raw material procurement for termite fishing tools by wild chimpanzees in the Issa valley, Western Tanzania.

Science.gov (United States)

Almeida-Warren, Katarina; Sommer, Volker; Piel, Alex K; Pascual-Garrido, Alejandra

2017-10-01

Chimpanzee termite fishing has been studied for decades, yet the selective processes preceding the manufacture of fishing tools remain largely unexplored. We investigate raw material selection and potential evidence of forward planning in the chimpanzees of Issa valley, western Tanzania. Using traditional archaeological methods, we surveyed the location of plants from where chimpanzees sourced raw material to manufacture termite fishing tools, relative to targeted mounds. We measured raw material abundance to test for availability and selection. Statistics included Chi-Squared, two-tailed Wilcoxon, and Kruskall-Wallace tests. Issa chimpanzees manufactured extraction tools only from bark, despite availability of other suitable materials (e.g., twigs), and selected particular plant species as raw material sources, which they often also exploit for food. Most plants were sourced 1-16 m away from the mound, with a maximum of 33 m. The line of sight from the targeted mound was obscured for a quarter of these plants. The exclusive use of bark tools despite availability of other suitable materials indicates a possible cultural preference. The fact that Issa chimpanzees select specific plant species and travel some distance to source them suggests some degree of selectivity and, potentially, forward planning. Our results have implications for the reconstruction of early hominin behaviors, particularly with regard to the use of perishable tools, which remain archaeologically invisible. © 2017 Wiley Periodicals, Inc.

Hydrolysis technology for producing sugars from biomass as raw material for the chemical industry- SugarTech

Energy Technology Data Exchange (ETDEWEB)

Kallioinen, A.; Hytoenen, E.; Haekkinen, M. (VTT Technical Research Centre of Finland, Espoo (Finland)), email: anne.kallioinen@vtt.fi (and others)

2011-11-15

In the SugarTech project, spruce, forest residue, birch and sugar cane bagasse have been studied as raw materials for production of sugars to be processed further to ethanol or other chemicals. These raw materials, containing high proportion of carbohydrates have been analysed and pretreated for enzymatic hydrolysis by steam explosion and oxidative methods. The pretreated materials have been studied in respect to yield and enzymatic hydrolysability. Small carboxylic acids were an interesting side product from oxidation pretreatment. For feasibility study, 8 process cases have been selected and will be compared. Optimal enzyme mixtures have been determined for hydrolysis of pretreated materials. Results show that optimal enzyme composition depends clearly on the raw material and the pretreatment method. Pretreated raw materials were also hydrolysed efficiently in high dry matter conditions with commercial enzymes. Enzyme adsorption and desorption were studied with lignocellulosic substrates aiming at recycling of enzymes in the hydrolysis process. After enzymatic hydrolysis, a major part of the enzymes remained bound to substrate in spite of high degree of hydrolysis. Desorption of enzymes could only be detected with catalytically oxidised spruce. In addition, the induction of hydrolytic system of Trichoderma reesei, which is a widely used fungus for cellulase enzyme production, has been studied in the presence of different substrates. The substrate and the pretreatment method had clear effects on gene expression profile. (orig.)

Date fruit: chemical composition, nutritional and medicinal values, products.

Science.gov (United States)

Tang, Zhen-Xing; Shi, Lu-E; Aleid, Salah M

2013-08-15

Date fruit has served as a staple food in the Arab world for centuries. Worldwide production of date fruit has increased almost threefold over the last 40 years, reaching 7.68 million tons in 2010. Date fruit can provide many essential nutrients and potential health benefits to the consumer. Date fruit goes through four ripening stages named kimri, khalal, rutab and tamer. The main chemical components of date fruit include carbohydrates, dietary fibre, enzymes, protein, fat, minerals, vitamins, phenolic acids and carotenoids. The chemical composition of date fruit varies according to ripening stage, cultivar, growing environment, postharvest conditions, etc. The nutritional and medicinal activities of date fruit are related to its chemical composition. Many studies have shown that date fruit has antioxidant, antimutagenic, anti-inflammatory, gastroprotective, hepatoprotective, nephroprotective, anticancer and immunostimulant activities. Various date fruit-based products such as date syrup, date paste, date juice and their derived products are available. Date by-products can be used as raw materials for the production of value-added products such as organic acids, exopolysaccharides, antibiotics, date-flavoured probiotic-fermented dairy produce, bakery yeasts, etc. In this paper the chemical composition and nutritional and medicinal values of date fruit as well as date fruit-based products are reviewed. © 2013 Society of Chemical Industry.

Calibration curves of a PGNAA system for cement raw material analysis using the MCNP code

International Nuclear Information System (INIS)

Oliveira, Carlos; Salgado, Jose

1998-01-01

In large samples, the γ-ray count rate of a prompt gamma neutron activation analysis system is a multi-variable function of the elemental dry composition, density, water content and thickness of the material. The experimental calibration curves require tremendous laboratory work, using a great number of standards with well-known compositions. Although a Monte Carlo simulation study does not avoid the experimental calibration work, it reduces the number of experimental calibration standards. This paper is part of a feasibility study for a PGNAA system for on-line continuous characterisation of cement raw material conveyed on a belt (Oliveira, C., Salgado, J. and Carvalho, F. G. (1997) Optimisation of PGNAA instrument design for cement raw materials using the MCNP code. J. Radioanal. Nucl. Chem. 216(2), 191-198; Oliveira, C., Salgado, J., Goncalves, I. F., Carvalho, F. G. and Leitao, F. (1997a) A Monte Carlo study of the influence of geometry arrangements and structural materials on a PGNAA system performance for cement raw materials analysis. Appl. Radiat. Isot. (accepted); Oliveira, C., Salgado, J. and Leitao, F. (1997b) Density and water content corrections in the gamma count rate of a PGNAA system for cement raw material analysis using the MCNP code. Appl. Radiat. Isot. (accepted).]. It reports on the influence of the density, mass water content and thickness on the calibration curves of the PGNAA system. The MCNP-4A code, running in a Pentium-PC and in a DEC workstation, was used to simulate the PGNAA configuration system

Vegan Triple-Ironman (Raw Vegetables/Fruits)

OpenAIRE

Leischik, Roman; Spelsberg, Norman

2014-01-01

Endurance sport requires a healthy and balanced diet. In this case report we present the findings of an ultra-triathlete (three times Ironman, means 11.4 km swim, 540 km bike, 125 km run in 41:18 h as a whole) living on a raw vegan diet and having finished the competitions under these nutritional conditions. To this end, the vegan ultra triathlete and a control group of 10 Ironman triathletes of similar age living on a mixed diet were investigated, using echocardiography and spiroergometry. I...

Decontamination of drug vegetative raw material by relativistic electron beam

International Nuclear Information System (INIS)

Gorbanyuk, A.G.; Dikiy, I.L.; Yegorov, A.M.; Linnik, A.F.; Uskov, V.V.

2004-01-01

The new technology of decontamination of drug vegetative raw material and medical products is proposed. Advantages of use of relativistic beams in a range of electron energies from 0.5 MeV to 5 MeV for these purposes are shown in comparison with X-radiation of energy from 80 keV to 1 MeV

Lime kiln dust as a potential raw material in portland cement manufacturing

Science.gov (United States)

Miller, M. Michael; Callaghan, Robert M.

2004-01-01

In the United States, the manufacture of portland cement involves burning in a rotary kiln a finely ground proportional mix of raw materials. The raw material mix provides the required chemical combination of calcium, silicon, aluminum, iron, and small amounts of other ingredients. The majority of calcium is supplied in the form of calcium carbonate usually from limestone. Other sources including waste materials or byproducts from other industries can be used to supply calcium (or lime, CaO), provided they have sufficiently high CaO content, have low magnesia content (less than 5 percent), and are competitive with limestone in terms of cost and adequacy of supply. In the United States, the lime industry produces large amounts of lime kiln dust (LKD), which is collected by dust control systems. This LKD may be a supplemental source of calcium for cement plants, if the lime and cement plants are located near enough to each other to make the arrangement economical.

Characterization of Limestone as Raw Material to Hydrated Lime

Science.gov (United States)

Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

2018-03-01

In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

Rambutan Seed (Nephelium Lappaceum L.) Optimization as Raw Material of High Nutrition Value Processed Food

Science.gov (United States)

Wahini, M.; Miranti, M. G.; Lukitasari, F.; Novela, L.

2018-02-01

Rambutan (Nephelium Lappaceum L.) is a plant that identical with Southeast Asian countries, in some areas of Indonesia no exception, but rambutan seed is considered as a waste. Therefore, it needs to be optimized into raw materials of food and processed with high nutritional value and has economic value. The purpose of this research were: 1) to find the best rambutan seed immersion formula; 2) to know the nutritional value of the best immersed rambutan seed; 3) to produce raw material and various processed of rambutan seed product. The research method was quasi experiment with 6 treatments and 2 factorial design, materials for immersion was NaCl and Ca(OH)2. The results showed that: 1) the best rambutan seed immersion formula was using Ca(OH)2; 2) the best rambutan seed contains 1,6 ash, 31,2 protein, 26,9 fat; 3) the best rambutan seed produce flour and processed of seasoned nuts. This research indicates that rambutan seed is very potential to be an alternative high-value raw materials.

Utilization of flotation wastes of copper slag as raw material in cement production

International Nuclear Information System (INIS)

Alp, I.; Deveci, H.; Suenguen, H.

2008-01-01

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe 2 O 3 mainly in the form of fayalite (Fe 2 SiO 4 ) and magnetite (Fe 3 O 4 ). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials

Utilization of flotation wastes of copper slag as raw material in cement production.

Science.gov (United States)

Alp, I; Deveci, H; Süngün, H

2008-11-30

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe(2)O(3) mainly in the form of fayalite (Fe(2)SiO(4)) and magnetite (Fe(3)O(4)). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials.

VERAM, for a sustainable and competitive future for EU Raw Materials

Science.gov (United States)

Mobili, A.; Tittarelli, F.; Revel, G. M.; Wall, P.

2018-03-01

The project, VERAM “Vision and Roadmap for European Raw Materials”, aims to deliver a mapping of on-going initiatives on non-food, non-energy raw materials (including metals, industrial minerals, aggregates and wood) at European, Member State, and regional levels both from the Research and Innovation (R&I), industry, and policy perspectives. Moreover, based on a comprehensive gap analysis, VERAM will propose a common long term 2050 Vision and Roadmap in coordination and cooperation with all stakeholders across the value chain. For the first time, two European Technology Platforms (ETPs) together with their corresponding European Research Area Networks (ERA-NETs) are joining forces to develop a common roadmap.

STUDY ON THE VALORIFICATION OF LYCIUM BARBARUM FRUIT (GOJI IN PASTRY PRODUCTS

Directory of Open Access Journals (Sweden)

Anamaria Pop

2013-11-01

Full Text Available The aim of this research refers to the development of new recipes of fabricating tow different muffins and spritz cookies, using Goji whole fruits rehydrated and Goji ground powder type fruits, in different proportions and after, by sensory analysis proving the consumer preferences in relation to Goji fruit intake in the products. Also has been studied the total carotenoid content by spectrophotometric measurements from finished products comparing with whole goji berry fruit. The products are obtained by baking dough made ​​from flour, sugar, eggs, vegetable fat, milk, goji berries, friable chemical. The raw material and auxiliary material (white flour and Goji berries and the pastry products obtain with addition of goji was submitted to the physio-chemical exam, following: moisture content, ash content, gluten content, acidity content, vitamin C content, carotenoids content in accordance with applicable standards. Therefore we obtained 3 types of muffins (simple muffins, muffins with addition of 10% whole goji fruit, muffins with addition of 10% fruit goji powder ground type and 4 types of spritz cookies (simple cookies, cookies with addition of 3 %, 5 %, 10 % of goji powder.

Uranium in phosphorus-bearing raw materials and technological problems of its recovery

Energy Technology Data Exchange (ETDEWEB)

Gorecki, H; Gorecka, H [Politechnika Wroclawska (Poland)

1981-01-01

A problem of uranium recovery from phosphorus-bearinq raw materials is discussed. The different methods of uranium recovery from extractive phosphoric acid are briefly described. The information on their applications in the industry is also given.

21 CFR 1304.31 - Reports from manufacturers importing narcotic raw material.

Science.gov (United States)

2010-04-01

... therefrom. (g) All in-process inventories should be expressed in terms of end-products and not precursors... following information shall be submitted for each type of narcotic raw material (quantities are expressed as... opium, crude alkaloids and other derivatives (quantities are expressed as grams of anhydrous base or...

Energies and raw materials. The energy situation

International Nuclear Information System (INIS)

1997-09-01

Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in September 1997: primary energy total consumption has increased (mobile year) of 1.1%, at the same rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 5.9%), slight increase for petroleum products (+ 0.8%), strong increase for gas (+ 3.2%) and moderate increase for electricity (+ 1.7%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a record energy cost level with + 30% on one year, reaching 89.2 billions Francs, to be compared to 68.5 in September 1996

Raman, Infrared, and Laser-Induced Breakdown Spectroscopy Identification of Particles in Raw Materials.

Science.gov (United States)

Lee, Kathryn; Lankers, Markus; Valet, Oliver

2018-02-01

Raw materials need to be of a certain quality with respect to physical and chemical composition. They also need to have no contaminants, including particles, because these could indicate raw material impurities or contaminate the product. Particle identification allows determination of process conditions that caused them and whether the quality of the final product is acceptable. Particles may appear to the eye to be very different things than they actually are. They may be coated with the raw material and may consist of several components; therefore, chemical and elemental analyses are required for accuracy in proper identification and definitive information about their source. Thus, microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and infrared (IR) spectroscopy are excellent tools for identifying particles in materials. Those tools are fast and accurate, and can provide chemical and elemental composition as well as images that can aid identification. The micro-analysis capabilities allow for easy analysis of different portions of samples so that multiple components can be identified and sample preparation can be reduced or eliminated. The differences in sensitivities of Raman and IR spectroscopies to different functional groups as well as the elemental analysis provided by LIBS and the image analysis provided by the microscopy makes these complementary techniques and provides the advantage of identifying various chemical components. Proper spectral searching techniques and interpretation of the results are important for interpretation and identification of trace contaminants.

Investigation and analysis on ITER in-vessel coils’ raw-materials

International Nuclear Information System (INIS)

Jin, Huan; Wu, Yu; Long, Feng; Yu, Min; Han, Qiyang; Liu, Huajun

2013-01-01

Highlights: • The R and D works for the ITER in-vessel coils (IVC) are now being conducted in Institute of Plasma Physics, and the analysis work are being done by Princeton Plasma Physics Laboratory. • There is little published paper about the raw materials for ITER IVC coils. • This manuscript points out the progress of the selected materials for ITER IVC coils. -- Abstract: The ITER in-vessel coils (IVCs) consist of 27 coils edge localized modes (ELM) and 2 coils vertical stabilization (VS) which are all mounted on the vacuum vessel wall behind the shield modules. The IVCs design and manufacturing work is being conducted in between Institute of Plasma Physics Chinese Academy of Sciences (ASIPP) and Princeton Plasma Physics Laboratory (PPPL). Because the position of ELM and VS coils is close and face to the plasma, the IVCs must undergo a severe environment, such as the high dose of radiation and high operation temperature, thus the conventional electrical insulation materials cannot be used. And the technology of “Stainless Steel Jacketed Mineral Insulated Conductor” (SSMIC) is deemed as the best choice to provide the necessary radiation resistance and compatibility strength in ITER's vacuum vessel. While mineral insulated conductor technology is not new, and is similar to the mineral insulated cable used in industrial. Some difficulties still need to be solved, such as searching for the proper raw-materials to make sure that the conductor have the properties of high current carrying capability, the necessary radiation resistance, the proper strength, at the same time, it must be come true in manufacture technology. This paper described the analysis of the materials for VS and ELM coil conductor

66. The safety engineering at reprocessing of raw material from 'zero' mark and 'slaked lime'

International Nuclear Information System (INIS)

Ivanov, A.V.

1993-01-01

The safety engineering at reprocessing of raw material from 'zero' mark and 'slaked lime' was studied. All operational conditions at reprocessing of raw material from 'zero' mark and 'slaked lime' were discussed.

Uranium refining in South Africa. The production of uranium trioxide, considering raw material properties and nuclear purity requirements

International Nuclear Information System (INIS)

Colborn, R.P.; Bayne, D.L.G.; Slabber, M.N.

1980-01-01

Conventional practice results in raw materials being delivered to the uranium refineries in a form more suitable for transportation than for processing, and therefore the refineries are required to treat these raw materials to produce an acceptable intermediate feed stock. During this treatment, it is advantageous to include a purification step to ensure that the feed stock is of the required purity for nuclear grade uranium hexafluoride production, and this usually results in ammonium diuranate slurries of the required quality being produced as the intermediate feed stock. All subsequent processing steps can therefore be standardized and are effectively independent of the origin of the raw materials. It is established practice in South Africa to transport uranium as an ammonium diuranate slurry from the various mines to the Nufcor central processing plant for UOC production, and therefore the process for the production of uranium hexafluoride in South Africa was designed to take cognizance of existing transport techniques and to accept ammonium diuranate slurries as the raw material. The South African refinery will be able to process these slurries directly to uranium trioxide. This paper discusses the conditions under which the various ammonium diuranate raw materials, exhibiting a wide range of properties, can be effectively processed to produce a uranium trioxide of acceptably consistent properties. Mention is also made of the uranium hexafluoride distillation process adopted

DELINEATION OF BOUNDARY CONTOURS OF MINERAL RAW MATERIALS WITHIN THE DEPOSIT SPACE CONSIDERING THE QUALITY

Directory of Open Access Journals (Sweden)

Ivan Tomašić

1990-12-01

Full Text Available On the basis of performed explorations, in the phase of deposit preparation and development for exploitation the obtained results regarding the raw material quality were transfered to the surface. The results served both for the development and planning of deposit excavation dynamics and for the delineation of boundary contours by mineral raw materials within the deposit space considering the quality, The case presented in the article refers to the marl and limestone open pit for the cement industry, the »Partizan« near Split (the paper is published in Croatian.

1.2. X-ray phase analysis of borosilicate raw material

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

2015-01-01

Present article is devoted to X-ray phase analysis of borosilicate raw material. The thermo gram of initial borosilicate ore was considered. The X-ray pattern of initial danburite of Ak-Arhar Deposit was considered as well. The X-ray pattern of danburite of Ak-Arhar Deposit after pre-baking was studied. The X-ray pattern of initial danburite concentrate was studied as well.

Petroleum as a raw material resource for sustainable development

International Nuclear Information System (INIS)

Egorov, O.I.

1996-01-01

Author notes that for economic and social region development it is necessary has been created large petroleum chemical plants near by Atyrau city (initial raw material - Tengiz, Korolev and other petroleum deposits of this region) and Aktau (Mangistau and Bazuchin petroleum). Realization of projects for structure changes of petroleum and gas region demands a great investments. It is noted that growing scales of petroleum and gas resources mastering calls already a considerable environmental complications because of Caspian Sea's level marking rise

WATER-JET CUTTING MACHINE NOW AVAILABLE FROM THE CERN RAW MATERIALS STORES

CERN Multimedia

2007-01-01

The CERN Raw Materials Stores has recently acquired a new water-jet cutting machine. The machine is capable of cutting all types and shapes of materials up to 70 mm in thickness, with an accuracy of +/- 0.1mm/m. For the time being, users requiring materials to be cut should supply drawings in DXF, DWG or IGES (AutoCad) file format. The machine will be operational as of 1st October 2007. The Stores Team Paulo Dos Santos FI-LS-MM 72308

Energies and raw materials. The energy situation

International Nuclear Information System (INIS)

1997-11-01

Statistics are given on the energy and raw materials (coal, oil, etc.) production and consumption levels in France in November 1997: primary energy total consumption has increased (mobile year) of 0.6%, at a slightly inferior rate than the rate since 3 years. Interior demand has varied depending on the energy: strong decrease for coal (- 9.3%), slight increase for petroleum products (+ 1.2%), markedly slowing down increase for gas (+ 1.4%) and moderate increase for electricity (+ 1.3%). An increase in the dollar exchange rate and a high level of oil and gas imports have induced a maintained high energy cost level with + 14% on one year, reaching 86.8 billions Francs, to be compared to 76.1 in November 1996

Raw material variability of an active pharmaceutical ingredient and its relevance for processability in secondary continuous pharmaceutical manufacturing.

Science.gov (United States)

Stauffer, F; Vanhoorne, V; Pilcer, G; Chavez, P-F; Rome, S; Schubert, M A; Aerts, L; De Beer, T

2018-06-01

Active Pharmaceutical Ingredients (API) raw material variability is not always thoroughly considered during pharmaceutical process development, mainly due to low quantities of drug substance available. However, synthesis, crystallization routes and production sites evolve during product development and product life cycle leading to changes in physical material attributes which can potentially affect their processability. Recent literature highlights the need for a global approach to understand the link between material synthesis, material variability, process and product quality. The study described in this article aims at explaining the raw material variability of an API using extensive material characterization on a restricted number of representative batches using multivariate data analysis. It is part of a larger investigation trying to link the API drug substance manufacturing process, the resulting physical API raw material attributes and the drug product continuous manufacturing process. Eight API batches produced using different synthetic routes, crystallization, drying, delumping processes and processing equipment were characterized, extensively. Seventeen properties from seven characterization techniques were retained for further analysis using Principal Component Analysis (PCA). Three principal components (PCs) were sufficient to explain 92.9% of the API raw material variability. The first PC was related to crystal length, agglomerate size and fraction, flowability and electrostatic charging. The second PC was driven by the span of the particle size distribution and the agglomerates strength. The third PC was related to surface energy. Additionally, the PCA allowed to summarize the API batch-to-batch variability in only three PCs which can be used in future drug product development studies to quantitatively evaluate the impact of the API raw material variability upon the drug product process. The approach described in this article could be applied to any

SCREENING OF ANTIMICROBIAL PROPERTIES OF ETHANOLIC EXTRACTS FROM SOME KINDS OF RAW MATERIALS WITH QUINONEDERIVATIVES

Directory of Open Access Journals (Sweden)

Boyko N.N.

2014-12-01

Full Text Available This paper presents data on screening of antimicrobial properties of extracts from some kinds of raw materials (18 plants with hydroquinone, naphtoquinone or anthraquinone derivatives. Some technological parameters of extracts (density and concentration of extraneous substances have been determined. The most appropriate microbiological method of studying antimicrobial properties of extracts, diffusion method of “well”, has been applied; special mathematic method of comparison of antimicrobial properties of extracts vector analysis has been applied in order to study and to compare antimicrobial properties of extracts. Indexes of antimicrobial properties of extracts have been determined: a complex index of medicinal product antimicrobial activity for quantitative estimation of antimicrobial effect - A, and square of correlation coefficient - r², which demonstrates the spectrum of antimicrobial activity of the extracts (degree of similarity to the standard. The most active extracts have been selected; they have antimicrobial properties of medium strength: from the herb of chimaphila umbellata А=2.20; the fruits of rhamnus cathartica А=2.12; the root of rubia tinctorum А=2.11; the bark of frangula alnus А=2.05; the root of rumex confertus А=2.04; the leaf of pyrola rotundifolia А=2.00; and leaf of arctostaphylos uva-ursi А=2.08 (but extract from uva-ursi did not affected on 2 strains of microorganisms r²=0.64. Low levels of antimicrobial activity have been demonstrated by the extract obtained from the leaf of urtica dioica А=0.72, r²=0.34. The mean result of the complex index of antimicrobial activity for the most of extracts from plants containing quinonederivatives is A = 1.77 (on 70% vol. ethanol at a ratio of raw material : extracting agent – 1:7 wt. : vol. and may range from 0.68 to 2.85. The mean result of the correlation coefficient is r = 0.93 and may range from 0.59 to 0.99. The mean result of the concentration of

Study of diffusion processes in pumpkin particles during candied fruits production

Directory of Open Access Journals (Sweden)

V. Atamanyuk

2017-12-01

Full Text Available The production of candied fruits is a priority development area of the food industry. The basic process in candied fruits production is diffusion of sugar syrup into vegetable raw material. Kinetics of the diffusion processes depends on sucrose concentration, medium temperature, particles size and internal structure of the fruits.The experiments to determine the factors influencing the diffusion processes were carried out using the installation designed by the authors; the experimental dependences of sucrose concentration change in pumpkin candied fruits on time have been determined at temperatures of 20, 40, 60 and 80°C. Cell sizes and diameter of pores between the cells in raw and blanched pumpkin have been determined. This makes it possible to determine the internal porosity of the pumpkin particle, the value of which determines the coefficient of mass transfer.On the basis of the experiments we derived the dependence, allowing to determine the mass transfer coefficients for sucrose molecules in blanched pumpkin fruits within the temperatures corresponding to the quality of the finished product. The experimental studies and the chosen mathematical model allow us to calculate the change in sucrose concentration in the pumpkin fruits in time at different temperatures and to determine the time required for the candied fruits to reach the equilibrium concentration. Also, the coefficients not depending on temperature, but depending only on the shape of the particles being saturated with sugar syrup, have been determined using the kinetic model of diffusion processes. The obtained theoretical dependences are in good agreement with the experimental data and substantiate the expediency of the chosen temperature and concentration ranges. The designed installation, the obtained experimental and theoretical dependences, and the calculated coefficients allow to create an intensive sucrose diffusion process in pumpkin particles during pumpkin candied

4.2. The kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

2015-01-01

Present article is devoted to kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit. The dependence of nitric acid decomposition of calcined boric raw material for extraction of boron oxide on temperature (20-100 deg C) and process duration (15-60 minutes) was defined. It was defined that at temperature increasing the extraction rate of boron oxide increases from 20.8 to 78.6%.

Dependence of quality properties for grey iron on used raw materials

Directory of Open Access Journals (Sweden)

E. Weiss

2009-01-01

Full Text Available Grey iron castings keep the first place among castings on base of iron. Present trend in growing entrance production costs of cast stock force manufacturer to cost minimizing. Therefore is most actual deal replacement pig iron by steel scrap. In contribution are presented results research work relating to influence of raw materials on grey iron properties.

Cocoa pulp juice (sweatings) as a potential raw material for the ...

African Journals Online (AJOL)

Cocoa sweatings is a very interesting by-product of cocoa production and it forms the substrate for microbial growth during the fermentation process. Most of the sweatings go to waste during the processing of the cocoa beans and this has led to its utilization as a potential raw material for the development of soft drink to ...

Potential of Technogenic Mineral Raw Materials in Russia and the Issues of its Rational Use

Directory of Open Access Journals (Sweden)

Larisa Ivanovna Goncharova

2015-11-01

Full Text Available The increasing negative impact of mining waste on natural ecosystems often leads to their irreversible destruction, a trend that is gradually becoming global. The particular relevance of the research is explained, on the one hand, by the possibilities of minimization of specific volumes of formation of mining waste in all types of industries; on the other hand, by the possibilities of maximization of comp rehensive use of their valuable components as secondary material resources on an economically rational basis and the possibilities of restoring the disturbed natural environment. The rational use of natural and technogenic mineral raw materials is greatly facilitated by the geological exploration and geological-economic evaluation of the resources, which requires the development of specific methodological approaches to the economic justification of resource estimation parameters for outlining and calculating the multicomponent commercial reserves of raw materials and separate valuable components in them. Analysis shows that researchers’ opinions on a number of methodological principles of sustainable mining, complex processing of multicomponent materials are often contradictory. Scientific publications do not consider the issue of the price valuation of mining waste as secondary material resources. Mining waste processing should be considered as an important part of the overall socio-ecological-economic system for rational nature management. The analysis of the existing practice of using the mining waste should be based on the system approach and take into consideration geological, technological, economic, environmental and social characteristics throughout the cycle of production, combined processing and treatment of secondary waste according to the principle “from the earth to the earth”. The article identifies the main barriers to the recycling of mining wastes, proposes several methodological guidelines for the sustainable mining and

Radiation decontamination of pharmaceutical raw materials as an integral part of the good pharmaceutical manufacturing practice (GPMP)

Energy Technology Data Exchange (ETDEWEB)

Razem, D; Katusin-Razem, B [Institut Rudjer Boskovic, Zagreb (Yugoslavia); Starcevic, M; Galekovic, B [PLIVA Pharmaceutical Works, Zagreb (Yugoslavia)

1990-01-01

The microbiological quality of many raw materials used in the manufacture of pharmaceuticals and adjuvants often fails to meet the standards set by the pharmaceutical industry. Raw materials of biological provenience are particularly susceptible to contamination. This work describes the present situation regarding the microbial load of corn starch. Given the accepted microbiological criteria, irradiation treatment is proposed as integral to Good Pharmaceutical Manufacturing Practice (GPMP). The use of total viable count as a guide for specifying microbial limits for non-sterile materials is supported. Criteria for the choice of dose are discussed. (author).

Radiation decontamination of pharmaceutical raw materials as an integral part of the good pharmaceutical manufacturing practice (GPMP)

International Nuclear Information System (INIS)

Razem, D.; Katusin-Razem, B.; Starcevic, M.; Galekovic, B.

1990-01-01

The microbiological quality of many raw materials used in the manufacture of pharmaceuticals and adjuvants often fails to meet the standards set by the pharmaceutical industry. Raw materials of biological provenience are particularly susceptible to contamination. This work describes the present situation regarding the microbial load of corn starch. Given the accepted microbiological criteria, irradiation treatment is proposed as integral to Good Pharmaceutical Manufacturing Practice (GPMP). The use of total viable count as a guide for specifying microbial limits for non-sterile materials is supported. Criteria for the choice of dose are discussed. (author)

Utilization of Delignified Sawdust as Raw Material of Biogas Production

Directory of Open Access Journals (Sweden)

Zumalla Asfarina

2018-01-01

Full Text Available Biogas is one alternative to replace the irreplaceable energy source that has begun to diminish its existence. The raw materials for biogas manufacture are renewable biomass, usually using plantation waste, agriculture, and livestock. Using biogas can also reduce environmental pollution. One of the agricultural waste that has great potential to become the raw material of biogas is teak sawdust. Wood processing industry in Indonesia quite a lot, but wood has a high lignosesluosa content, so it needs the right method to process it. With the delignification of lignin levels on teak sawdust will decrease. Wood sawdust is soaked using NaOH for 1, 2, 3, and 4 days with 4% w / v concentration. The lowest lignin and hemicellulose content was 25.79% and 87.9% in pretreatment for 4 days, while the highest cellulose level was 57, 34%. The accumulated volume of biogas at 1 day pretreatment, ie 709 ml / g TS. Gcms shows the enlarged peak area of methanamine, N-methyl from before pretreatment. The fastest biogas formation (λ in 4 days pretreatment, 1.60403 days and the largest constant A and U variables at 1 day were 914.5903 ml / g TS and 34.59765 ml / g TS.

Annual report 2001. General direction of energy and raw materials

International Nuclear Information System (INIS)

2001-01-01

This report summarizes the 2001 activity of the French general direction of energy and raw materials (DGEMP) of the ministry of finances and industry: 1 - security of energy supplies: a recurrent problem; 2001, a transition year for nuclear energy worldwide; petroleum refining in font of the 2005 dead-line; the OPEC and the upset of the oil market; the pluri-annual planning of power production investments; renewable energies: a reconfirmed priority; 2 - the opening of markets: the opening of French electricity and gas markets; the international development of Electricite de France (EdF) and of Gaz de France (GdF); electricity and gas industries: first branch agreements; 3 - the present-day topics: 2001, the year of objective contracts; AREVA, the future to be prepared; the new IRSN; the agreements on climate and the energy policy; the mastery of domestic energy consumptions; the safety of hydroelectric dams; Technip-Coflexip: the birth of a para-petroleum industry giant; the cleansing of the mining activity in French Guyana; the future of workmen of Lorraine basin coal mines; 4 - 2001 at a glance: highlights; main legislative and regulatory texts; 5 - DGEMP: November 2001 reorganization and new organization chart; energy and raw materials publications; www.industrie.gouv.fr/energie. (J.S.)

Effect of salt, kinnow and pomegranate fruit by-product powders on color and oxidative stability of raw ground goat meat during refrigerated storage.

Science.gov (United States)

Devatkal, Suresh K; Naveena, B M

2010-06-01

Effects of salt, kinnow and pomegranate fruit by-product powders on color and oxidative stability of raw ground goat meat stored at 4+/-1 degrees C was evaluated. Five treatments evaluated include: control (only meat), MS (meat+2% salt), KRP (meat+2% salt+2% kinnow rind powder), PRP (meat+2% salt+2% pomegranate rind powder) and PSP (meat+2% salt+2% pomegranate seed powder). Addition of salt resulted in reduction of redness scores. Lightness increased in control and unchanged in others during storage. Redness scores declined and yellowness showed inconsistent changes during storage. Thiobarbituric acid reactive substances (TBARS) values were higher (PPRP>KRP>control>MS. Therefore, these powders have potential to be used as natural antioxidants to minimize the auto-oxidation and salt induced lipid oxidation in raw ground goat meat. Crown Copyright 2010. Published by Elsevier Ltd. All rights reserved.

Biodegradable packaging and edible coating for fresh-cut fruits and vegetables

Directory of Open Access Journals (Sweden)

Fernanda Galgano

2015-03-01

Full Text Available This work focuses on biodegradable packaging and edible coatings applied to fresh-cut fruits and vegetables and their effects on the product quality. Practical applications are mainly limited to the use of biodegradable materials that, however, do not allow full control of the product moisture loss. Better results can be achieved by the combined use of biodegradable packagings with edible coatings and recent research has shown that enrichment with silver montmorillonite nanoparticles may be a promising technique. However, the actual utilization of these materials is still limited, due to the high costs of the raw materials and the limited production.

Investigation of Inonotus obliquus (Pers. Pil. Extracts and Melanins after RF-plasma Treatment of Raw Material

Directory of Open Access Journals (Sweden)

O.Yu. Kuznetsova

2016-03-01

Full Text Available High-frequency capacitive discharge (RF plasma at low pressure was used as preliminary stage for the intensification of extraction from natural medicinal raw material. RF-plasma treatment was carried out in two modes differed by the nature of plasma-forming gas. Chaga (Inonotus obliquus (Pers. Pil. known as the birch mushroom was selected as a perspective source of raw material. Extraction was carried out in two ways – remaceration and maceration. The analy-sis of chaga extracts and melanins was performed using traditional techniques including determination of physical and chemical, antioxidant and spectral characteristics. The obtained extracts and melanins were compared to the control samples and literature data. RF-plasma treatment of medicinal raw material increased the yield of extractive substances, in particular of the main active component of chaga – melanin. The antioxidant activity of chaga extracts grew, while for melanins it remained at the level similar to that of control samples. The IR spectral characteristics of the studied chaga melanins are similar and agree well with the literature data. Insignificant deviations in the position and intensity of absorption strips were observed for the samples after RF treatment. IR spectra of the studied chaga melanins are similar to those for mushroom melanins, thereby confirming the similarity in their nature. RF-plasma treatment of chaga medicinal raw materials allows to modify them partially. The structural and mechanical properties of melanins modified by RF plasma remain the same.

Raw material changes and their processing parameters in an extrusion cooking process

DEFF Research Database (Denmark)

Cheng, Hongyuan; Friis, Alan

In this work, the effects of raw material and process parameters on product expansion in a fish feed extrusion process were investigated. Four different recipes were studied with a pilot-scale twin-screw co-rotating extruder according to a set of pre-defined processing conditions. In the four rec...

Elaborations in the area of complex reprocessing of mineral raw materials

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2002-01-01

In present time complex using of raw materials has important significance as it connected with solving problems of creating of waste less and ecologically clean technologies. Elaboration and assimilation of waste less technologies has special significance for chemical, mountain-chemical, metallurgical branches of industry. In this part of book author gives several methods of waste less and ecologically clean technologies

Quality and Sensorial Characteristics of Raw-Vegan Bars

OpenAIRE

Liana Claudia Salanţă; Maria Tofană; Sonia Socaci; Cristina Barta; Carmen Pop

2015-01-01

Increased consumer interest in healthier food products is driven by a variety of factors including growing awareness of the link between diet and health, the desire to age ‘gracefully’ by maintaining good health, greater convenience in meeting nutritional needs and preventing chronic diseases. In raw food diet, food is consumed predominantly or exclusively as uncooked and unprocessed raw food; the main components of the diet are fruits, nuts, seeds, and sprouted grains and beans. The aim of t...

Characterisation of Cements From Dominantly Volcanic Raw Materials of the Carpathian Bend Zone

Directory of Open Access Journals (Sweden)

Halmagy Timea

2016-12-01

Full Text Available This paper presents the results of laboratory investigations regarding the production of cements from local raw materials, such as limestone from Varghis, gypsum from Nucsoara, basaltic scoria from Racosul de Jos, volcanic tuff from Racosul de Sus, diatomite from Filia, and red mud from Oradea. The raw mixtures, based on modified Bogue calculations, contain limestone, gypsum, and one or two of the above-mentioned materials. The cements resulted from clinker grinding in a laboratory gas furnace at 1260-1300 °C, with one hour at the peak temperatures, and were characterised for Blaine specific surface area, specific density, and mineral phases. Physico-mechanical properties, such as water content for normal consistency, setting time, soundness, and compressive strength were also determined. Results show that these cements contain belite, ferrite, calcium sulphoaluminate, anhydrite, and some minor compounds.

Hook tool manufacture in New Caledonian crows: behavioural variation and the influence of raw materials.

Science.gov (United States)

Klump, Barbara C; Sugasawa, Shoko; St Clair, James J H; Rutz, Christian

2015-11-18

New Caledonian crows use a range of foraging tools, and are the only non-human species known to craft hooks. Based on a small number of observations, their manufacture of hooked stick tools has previously been described as a complex, multi-stage process. Tool behaviour is shaped by genetic predispositions, individual and social learning, and/or ecological influences, but disentangling the relative contributions of these factors remains a major research challenge. The properties of raw materials are an obvious, but largely overlooked, source of variation in tool-manufacture behaviour. We conducted experiments with wild-caught New Caledonian crows, to assess variation in their hooked stick tool making, and to investigate how raw-material properties affect the manufacture process. In Experiment 1, we showed that New Caledonian crows' manufacture of hooked stick tools can be much more variable than previously thought (85 tools by 18 subjects), and can involve two newly-discovered behaviours: 'pulling' for detaching stems and bending of the tool shaft. Crows' tool manufactures varied significantly: in the number of different action types employed; in the time spent processing the hook and bending the tool shaft; and in the structure of processing sequences. In Experiment 2, we examined the interaction of crows with raw materials of different properties, using a novel paradigm that enabled us to determine subjects' rank-ordered preferences (42 tools by 7 subjects). Plant properties influenced: the order in which crows selected stems; whether a hooked tool was manufactured; the time required to release a basic tool; and, possibly, the release technique, the number of behavioural actions, and aspects of processing behaviour. Results from Experiment 2 suggested that at least part of the natural behavioural variation observed in Experiment 1 is due to the effect of raw-material properties. Our discovery of novel manufacture behaviours indicates a plausible scenario for the

Consumption of raw vegetables and fruits: a risk factor for Campylobacter infections

NARCIS (Netherlands)

Verhoeff-Bakkenes, L.; Jansen, H.A.P.M.; Veld, in 't P.H.; Beumer, R.R.; Zwietering, M.H.; Leusden, van F.M.

2011-01-01

The purpose of this study was to determine the prevalence of Campylobacter in fresh vegetables and fruits at retail level in the Netherlands, and to estimate its implications on the importance of vegetables and fruits as risk factor for campylobacteriosis. Thirteen of the 5640 vegetable and fruit

PRACTICAL PROPOSALS AS A RESULT OF THEORETICAL AND EXPERIMENTAL STUDIES OF THE PROCESS OF EXTRACTION FROM RAW MATERIALS OF PLANT ORIGIN

Directory of Open Access Journals (Sweden)

I. I. Shishatskii

2014-01-01

Full Text Available Summary. Theoretical and experimental researches of extraction processes from plant origin raw materials: barley, acorns and chicory with liquid carbon dioxide, as well as lupin with cheese whey were carried out. Quality indicators of extracts and secondary raw materials are defined. It is established that they are perspective raw sources for the enriched and functional products as they contain amino acids, vitamins and microelements. The dairy-vegetative lupine extract, for example, contains 17 amino acids, including the essential as well as vitamins and minerals. The studies of secondary raw materials, barley, acorns, chicory and lupine quality showed the expediency of their use for foods enrichment. Quality indicators of secondary raw materials are presented in the tables form in the given work. It formed the basis for the development of hardware-technological schemes of obtaining СО2-extracts and their use. The hardware-technological scheme of obtaining СО2-extracts from barley, acorns and chicory includes a number of equipment units: motor transport for raw materials delivery to the enterprise, the scraper hydroconveyor, the jet washer, a photoseparator for of poor-quality raw materials and impurities removal, a blowing machine for removing surface moisture from the raw materials, a jet washer for peeling, a cutter, drying and frying device, a crusher, a roller machine tool and an extracting unit. Hardware providing for yoghurt technology enriched with amino acids, microelements and vitamins which are present in a dairy-plant extract differs from the mentioned above one in the following. The extract used is a cheese whey, and the extraction of a target component is carried out in a vibrating extractor. The hardwaretechnological scheme is made according to Russian technology of yoghurt and furnished with the equipment for dairy-vegetative extract feeding into a product. It includes the following: a vibrating extractor (not shown in fig

Identification of New Diterpenes as Putative Marker Compounds Distinguishing Agnus Castus Fruit (Chaste Tree) from Shrub Chaste Tree Fruit (Viticis Fructus).

Science.gov (United States)

Oshima, Naohiro; Masada, Sayaka; Suzuki, Ryuta; Yagi, Kanae; Matsufuji, Hiroshi; Suenaga, Emi; Takahashi, Yutaka; Yahagi, Tadahiro; Watanabe, Masato; Yahara, Shoji; Iida, Osamu; Kawahara, Nobuo; Maruyama, Takuro; Goda, Yukihiro; Hakamatsuka, Takashi

2016-01-01

Agnus Castus Fruit is defined in the European Pharmacopoeia as the dried ripe fruit of Vitex agnus-castus. In Europe it is used as a medicine targeting premenstrual syndrome and climacteric disorder. In Japan, Agnus Castus Fruit is becoming popular as a raw material for over-the-counter drugs and health food products, though its congenic species, Vitex rotundifolia and Vitex trifolia, have been used as Shrub Chaste Tree Fruit in traditional medicines. Therefore, it is important to discriminate these Vitex plants from the viewpoint of regulatory science. Here we tried to identify putative marker compounds that distinguish between Agnus Castus Fruit and Shrub Chaste Tree Fruit. We analyzed extracts of each crude drug by liquid chromatography-mass spectrometry, and performed differential analysis by comparison of each chromatogram to find one or more peaks characteristic of Agnus Castus Fruit. A peak was isolated and identified as an equilibrium mixture of new compounds named chastol (1) and epichastol (1a). The planar structures of 1 and 1a were determined spectroscopically. Their relative configurations were revealed by nuclear Overhauser effect spectroscopy and differential nuclear Overhauser effect-NMR data. Since avoiding contamination from closely related species is needed for the quality control of natural pharmaceuticals, this information will be valuable to establish a method for the quality control of both, Agnus Castus Fruit and Shrub Chaste Tree Fruit products. Georg Thieme Verlag KG Stuttgart · New York.

Influence of weight and type of planting material on fruit quality and its heterogeneity in pineapple [Ananas comosus (L.) Merrill].

Science.gov (United States)

Fassinou Hotegni, V Nicodème; Lommen, Willemien J M; Agbossou, Euloge K; Struik, Paul C

2014-01-01

Cultural practices can affect the quality of pineapple fruits and its variation. The objectives of this study were to investigate (a) effects of weight class and type of planting material on fruit quality, heterogeneity in quality and proportion and yield of fruits meeting European export standards, and (b) the improvement in quality, proportion and yield of fruits meeting export standards when flowering was induced at optimum time. Experiments were conducted in Benin with cvs Sugarloaf (a Perola type) and Smooth Cayenne. In cv. Sugarloaf, experimental factors were weight class of planting material (light, mixed, heavy) and time of flowering induction (farmers', optimum) (Experiment 1). In cv. Smooth Cayenne an additional experimental factor was the type of planting material (hapas, ground suckers, a mixture of the two) (Experiment 2). Fruits from heavy planting material had higher infructescence and fruit weights, longer infructescences, shorter crowns, and smaller crown: infructescence length than fruits from light planting material. The type of planting material in Experiment 2 did not significantly affect fruit quality except crown length: fruits from hapas had shorter crowns than those from ground suckers. Crops from heavy planting material had a higher proportion and yield of fruits meeting export standards than those from other weight classes in Experiment 1 only; also the type of planting material in Experiment 2 did not affect these variates. Heterogeneity in fruit quality was usually not reduced by selecting only light or heavy planting material instead of mixing weights; incidentally the coefficient of variation was significantly reduced in fruits from heavy slips only. Heterogeneity was also not reduced by not mixing hapas and ground suckers. Flowering induction at optimum time increased the proportion and yield of fruits meeting export standards in fruits from light and mixed slip weights and in those from the mixture of heavy hapas plus ground suckers.

Whey as a raw material for the production of functional beverages

Directory of Open Access Journals (Sweden)

Bulatović Maja Lj.

2012-01-01

Full Text Available One of the least utilized by-products of food industry, despite the great potential that is described, is the whey, which is obtained as a by-product of the technological process production of cheese and casein. The excess whey, which occurs in this process in very high yields, with failure to processing is becoming a very big polluter, what is completely at odds with the potential that such materials possess. On the other hand, the modern tempo and way of life, and increasingly polluted environmental also, impose the need to produce food products that would help the human body in the fight against harmful agents which are exposed to daily. One of the more effective solution is the production of fermented functional beverages based on whey, which achieved this intention in the most natural and most comfortable way. Considering the rather untapped potential of whey as a raw material and growing food shortages in the world market, the aim of this study was to analyze the possibilities of production of functional beverages based on whey, with satisfactory sensory characteristics, in order to demonstrate the attractiveness of whey as raw material in the food industry. This paper presents an overview of the wide possibilities for the use of whey with a special emphasis on its attractiveness and the necessity of its utilizing.

Taking the Step towards a More Dynamic View on Raw Material Criticality: An Indicator Based Analysis for Germany and Japan

Directory of Open Access Journals (Sweden)

Simon Glöser-Chahoud

2016-12-01

Full Text Available Due to mounting concerns about the security of raw material supplies, numerous studies dealing with the quantification of supply risks and material criticality at the national level have been carried out in previous years. Regarding these studies, most approaches are indicator based static screening methods analyzing large numbers of raw materials and identifying those which are most critical for an economy. The majority of these screening methods quantify supply risks and vulnerabilities for one base year without taking into account temporal changes. Dynamic approaches for specific raw materials analyzing affected value chains in detail have been introduced recently; however, these studies do not intend to provide a screening of larger numbers of commodities. In this paper, we present a simple dynamic screening approach to assess raw material criticality at the country level building upon methods from innovation economics. The indicators applied in this study are only based on broadly available production and trade data, which makes this approach relatively easy to apply. We test our methodology on the example of Germany and Japan—two economies with highly specialized industries and low domestic raw material deposits, and, hence, high import dependency. The results are comparable to those of previously conducted multi indicator based static screening methods. However, they provide additional insight into temporal developments over the previous decade.

The Mousterian lithic assemblage of the Ciota Ciara cave (Piedmont, Northern Italy: Exploitation and conditioning of raw materials

Directory of Open Access Journals (Sweden)

Sara Daffara

2014-09-01

Full Text Available The Ciota Ciara cave is situated in Monte Fenera’s karst (Borgosesia – Vercelli, at 670 metres above sea level. It is the most important evidence of a Middle Palaeolithic settlement in Piedmont: the cave was used by Homo neanderthalensis during the OIS 5, in a mild-humid period, as proven by faunal remains. The environment was characterized by deciduous woodland and glades. The intersection between different habitats, the presence of lithic raw materials, the karst morphology and water sources were certainly the main factors that encouraged human settlement during the Upper Pleistocene period, between 80.000 and 70.000 BP.In 2009 systematic excavations began in the cave by the University of Ferrara, in partnership with the Soprintendenza per i Beni Archeologici del Piemonte e del Museo di Antichità Egizie. Research focused on the cave’s atrium where three stratigraphic units were investigated: 13, 103 and 14.The exploited raw materials’ characterization were made by the stereo-microscope observations and through the SEM (Scanning Electron Microscope. Several lithologies are represented in different proportion: quartz is the predominant exploited raw material, followed by spongolite, sandstone, mylonite and opal. The archaeological record consists of various typologies of quartz: macro-crystalline pegmatite quartz, micro-crystalline pegmatite quartz and hyaline quartz. All these types of raw materials have been found in the proximity of the archaeological site, within 5 km range.The lithic assemblage is made of flakes, retouched tools, cores and debris. The raw materials exploitation was achieved through the direct percussion technique with various methods: S.S.D.A., discoid and Levallois. The reduction sequences on quartz are complete, although no refitting was found. The reduction sequence is not complete for most part of the other raw materials. The débitage products are small-medium size (1-4 cm and have different morphologies

HPLC-PDA Combined with Chemometrics for Quantitation of Active Components and Quality Assessment of Raw and Processed Fruits of Xanthium strumarium L.

Science.gov (United States)

Jiang, Hai; Yang, Liu; Xing, Xudong; Yan, Meiling; Guo, Xinyue; Yang, Bingyou; Wang, Qiuhong; Kuang, Haixue

2018-01-25

As a valuable herbal medicine, the fruits of Xanthium strumarium L. (Xanthii Fructus) have been widely used in raw and processed forms to achieve different therapeutic effects in practice. In this study, a comprehensive strategy was proposed for evaluating the active components in 30 batches of raw and processed Xanthii Fructus (RXF and PXF) samples, based on high-performance liquid chromatography coupled with photodiode array detection (HPLC-PDA). Twelve common peaks were detected and eight compounds of caffeoylquinic acids were simultaneously quantified in RXF and PXF. All the analytes were detected with satisfactory linearity (R² > 0.9991) over wide concentration ranges. Simultaneously, the chemically latent information was revealed by hierarchical cluster analysis (HCA) and principal component analysis (PCA). The results suggest that there were significant differences between RXF and PXF from different regions in terms of the content of eight caffeoylquinic acids. Potential chemical markers for XF were found during processing by chemometrics.

HPLC-PDA Combined with Chemometrics for Quantitation of Active Components and Quality Assessment of Raw and Processed Fruits of Xanthium strumarium L.

Directory of Open Access Journals (Sweden)

Hai Jiang

2018-01-01

Full Text Available As a valuable herbal medicine, the fruits of Xanthium strumarium L. (Xanthii Fructus have been widely used in raw and processed forms to achieve different therapeutic effects in practice. In this study, a comprehensive strategy was proposed for evaluating the active components in 30 batches of raw and processed Xanthii Fructus (RXF and PXF samples, based on high-performance liquid chromatography coupled with photodiode array detection (HPLC-PDA. Twelve common peaks were detected and eight compounds of caffeoylquinic acids were simultaneously quantified in RXF and PXF. All the analytes were detected with satisfactory linearity (R2 > 0.9991 over wide concentration ranges. Simultaneously, the chemically latent information was revealed by hierarchical cluster analysis (HCA and principal component analysis (PCA. The results suggest that there were significant differences between RXF and PXF from different regions in terms of the content of eight caffeoylquinic acids. Potential chemical markers for XF were found during processing by chemometrics.

Nuclear raw materials. Knowledge status after the Geneva conference (September 1958)

International Nuclear Information System (INIS)

Lecoq, M.; Mabile, J.; Carrat, G.; Ginocchio, A.; Roques, E.; Waynbaum, M.; Chervet, J.; Branche, G.; Geffroy, J.; Le Goff, M.

1959-05-01

The authors propose a synthesis of the numerous contributions presented at the Geneva conference. They first address deposits: uranium deposits (studies on uranium geochemistry and metallogeny, descriptions of various deposit types such as those associated with sedimentary layers or tectonic structures or petrographic types), thorium deposits, beryllium deposits, zirconium deposits. A second part addresses research methods and equipment: descriptive mineralogical studies, analytic physical or chemical methods, analytic field methods, isotope analysis, prospecting methods (geochemical techniques, radiometry, geophysical methods, general remarks on prospecting methods, organization of prospecting operations, and techniques of deep prospecting). The third part addresses the issues of reserves and resources: definitions, assessment techniques, geographical distribution of reserves and resources. The fourth part addresses the exploitation: quarries, underground exploitation, measures for personnel protection. The fifth part addresses ore concentration: determination of uranium ore and other raw material, concentration by physical means, ore concentration by chemical means, ore sampling, and plant monitoring and regulation. The last part addresses the economy of raw materials: uranium (cost price and production, and purchase and selling prices in different countries, world market in 1960 and on a longer term), thorium, beryllium, zirconium, lithium and helium

The Effect of Micro/Nano-metrics Size on the Interaction of Jordanian Aluminosilicate Raw Materials with High pH Solution

Science.gov (United States)

Aldabsheh, Islam; Garcia-Valles, Maite; Martinez, Salvador

2014-05-01

Environmental preservation has become a driving force behind the search for new sustainable and environmentally friendly composites to replace conventional concrete produced from ordinary Portland cement (OPC). Current researches concentrate on developing building products (geopolymers) through geopolymerization. The goal is to produce low cost construction materials for green housing. Geopolymerization is the process of polymerizing minerals with high silica and alumina at low temperature by the use of alkali solutions. Dissolution is the most important process for supplying the high initial Al and Si concentrations to produce the gel phase that is responsible for geopolymerization. This study has been focused on the influence of different micrometric particle sizes of three Jordanian raw materials on their dissolution behavior in sodium hydroxide solution. The samples are kaolinite, volcanic tuff and silica sand. The dissolution properties of each material, alone and mixed with the other two materials were studied in different concentrations (5 and 10 M) using (NaOH) at 25ºC, and shaking time for 24 and 168 h. To better understand the dissolution process, the alkaline solution was renewed after the desired time in order to know if the Al-Si raw material is completely dissolved or not. Different analytical techniques were used to characterize raw materials physically, mineralogically, chemically and thermally. All processed samples either centrifuged solutions or solid residues were fully characterized. The leached concentrations of Al and Si were determined by inductively coupled plasma (ICP). X-ray Diffraction Technique (XRD), Scanning Electron Microscopy (SEM), and Thermo Gravimetric Analysis (TGA) were used to evaluate the solid residue characterization compared with the original ones. The three aluminosilicate raw materials have indicated variable degrees of solubility under highly alkaline conditions. The method for the size reduction of the used raw

The increasing multifunctionality of Agricultural Raw Materials: Three dilemmas for Innovation and Adoption

NARCIS (Netherlands)

Boehlje, M.; Bröring, S.

2011-01-01

Agricultural raw materials are increasingly being used for multiple industries or sectors beyond the traditional fiber and nutrition industries: energy in the form of ethanol and biodiesel, industrial products such as polymers and bio-based synthetic chemicals and fibers, and pharmaceutical/health

Biotechnologies for critical raw material recovery from primary and secondary sources: R&D priorities and future perspectives.

Science.gov (United States)

Hennebel, Tom; Boon, Nico; Maes, Synthia; Lenz, Markus

2015-01-25

Europe is confronted with an increasing supply risk of critical raw materials. These can be defined as materials of which the risks of supply shortage and their impacts on the economy are higher compared to most of other raw materials. Within the framework of the EU Innovation Partnership on raw materials Initiative, a list of 14 critical materials was defined, including some bulk metals, industrial minerals, the platinum group metals and rare earth elements. To tackle the supply risk challenge, innovation is required with respect to sustainable primary mining, substitution of critical metals, and urban mining. In these three categories, biometallurgy can play a crucial role. Indeed, microbe-metal interactions have been successfully applied on full scale to win materials from primary sources, but are not sufficiently explored for metal recovery or recycling. On the one hand, this article gives an overview of the microbial strategies that are currently applied on full scale for biomining; on the other hand it identifies technologies, currently developed in the laboratory, which have a perspective for large scale metal recovery and the needs and challenges on which bio-metallurgical research should focus to achieve this ambitious goal. Copyright © 2013. Published by Elsevier B.V.

INCIDENCE OF FILAMENTOUS FUNGI WITH TOXIGENIC POTENTIAL ON SAMPLES OF FEED AND RAW MATERIALS FOR THEIR MANUFACTURE

Directory of Open Access Journals (Sweden)

Rodrigo Vera

2016-06-01

Full Text Available The presence and/or accumulation of mycotoxins in foods intended for human and animal nutrition is a constant concern for the harmful health effects resulting from ingestion. The aims of this communication were to analyze samples of feed and raw materials for manufacturing and to determine the presence of strains of filamentous fungi with toxigenic capacity. The values of frequency in the total samples (N = 422, indicated 63% of contamination, where A. flavus represented the most common (29.8%, while in feed and raw materials separately, indicated A. flavus has the highest value in both categories. In the analysis of different type of raw materials, A. flavus contaminated all types of samples, with the bran and soybean meal substrates having higher values for this Aspergillus, and corn substrate more fungal contamination. These results would demonstrate that the presence of mycobiota with toxigenic potential in food for animal feed is a disturbing reality.

Effects and detection of raw material variability on the performance of near-infrared calibration models for pharmaceutical products.

Science.gov (United States)

Igne, Benoit; Shi, Zhenqi; Drennen, James K; Anderson, Carl A

2014-02-01

The impact of raw material variability on the prediction ability of a near-infrared calibration model was studied. Calibrations, developed from a quaternary mixture design comprising theophylline anhydrous, lactose monohydrate, microcrystalline cellulose, and soluble starch, were challenged by intentional variation of raw material properties. A design with two theophylline physical forms, three lactose particle sizes, and two starch manufacturers was created to test model robustness. Further challenges to the models were accomplished through environmental conditions. Along with full-spectrum partial least squares (PLS) modeling, variable selection by dynamic backward PLS and genetic algorithms was utilized in an effort to mitigate the effects of raw material variability. In addition to evaluating models based on their prediction statistics, prediction residuals were analyzed by analyses of variance and model diagnostics (Hotelling's T(2) and Q residuals). Full-spectrum models were significantly affected by lactose particle size. Models developed by selecting variables gave lower prediction errors and proved to be a good approach to limit the effect of changing raw material characteristics. Hotelling's T(2) and Q residuals provided valuable information that was not detectable when studying only prediction trends. Diagnostic statistics were demonstrated to be critical in the appropriate interpretation of the prediction of quality parameters. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Hydrolysis technology for producing sugars from biomass as raw material for the chemical industry - SugarTech

Energy Technology Data Exchange (ETDEWEB)

Siika-aho, M.; Kallioinen, A.; Pakula, T. (and others) (VTT Technical Research Centre of Finland, Espoo (Finland)), email: matti.siika-aho@vtt.fi

2009-10-15

In SugarTech project, spruce, forest residue, birch and sugar cane bagasse have been studied as a raw material for production of sugars to be processed further to ethanol and other chemicals. These raw materials containing high proportion of carbohydrates have been analysed and pretreated for enzyme hydrolysis by steam explosion and oxidative methods. The pretreated materials have been studied in respect to yield and enzymatic hydrolysability. Birch and bagasse could easily be pretreated with steam explosion. Catalytic oxidation treatment of spruce produced material with superior hydrolysability to steam exploded material. Enzyme adsorption and desorption were studied aiming at recycling of enzymes in the hydrolysis process. Purified cellulase enzymes were found to have high tendency to adsorption on lignocellulosic substrate. Adsorption could be decreased by additives, e.g. urea and BSA. In addition, the hydrolytic system of Trichoderma reesei in the presence of different substrates has been studied. (orig.)

Physicochemical characterization of raw materials and co-products from the titanium dioxide industry

International Nuclear Information System (INIS)

Gazquez, M.J.; Bolivar, J.P.; Garcia-Tenorio, R.; Vaca, F.

2009-01-01

The present study was conducted to characterize several raw materials and co-products from the titanium dioxide industry in relation to their elemental composition (major, minor and trace elements), granulometry, mineralogy, microscopic morphology and physical composition. The main objective was to gain basic information for the future potential application of these co-products in fields such as agriculture, construction, civil engineering, etc. Microscopic studies were performed by applying scanning electron microscopy with X-ray microanalysis (SEM-XRMA) while the mineralogical compositions were analysed by means of the X-ray diffraction (XRD) technique. The concentrations of major elements such as Na, Al, Si, Ca, Ti, Fe, S and K were determined by X-ray fluorescence (XRF), while heavy metals and other trace elements were determined by ICP-MS. The physicochemical characterization of the raw materials used in the titanium dioxide industry, in addition to the characterization of the co-products generated, has enabled the evaluation of the degree of fractionation of different elements and compounds between the different co-products, as well as the control of the possible variations in the physicochemical composition of the raw materials throughout the time and the study of the influence of these variations in the characteristics of the obtained co-products. As a main conclusion of our study, it is possible to indicate that the levels of the pollutant elements associated to the co-products analysed were, in general, within safe limits and, therefore, they could potentially be used in composites as fertilizers or for building materials in road construction, etc. Nevertheless, for the specific application of each of these co-products in agriculture, construction and civil engineering, additional studies need to be performed to evaluate their appropriateness for the proposed application, together with specific studies on their health and environmental impact.

Raw materials evaluation and process development studies for conversion of biomass to sugars and ethanol

Energy Technology Data Exchange (ETDEWEB)

Wilke, C.R.; Yang, R.D.; Sciamanna, A.S.; Freitas, R.P.

1978-06-01

A range of cellulosic raw materials in the form of agricultural crop residue was analyzed for chemical composition and assessed for potential yields of sugars through chemical pretreatment and enzymatic hydrolysis of these materials. Corn stover was used as a representative raw material for a preliminary process design and economic assessment of the production of sugars and ethanol. With the process as presently developed, 23 gallons of ethanol can be obtained per ton of corn stover at a processing cost of about $1.80 per gallon exclusive of by-product credits. The analysis shows the cost of ethanol to be highly dependent upon (1) the cost of the biomass, (2) the extent of conversion to glucose, (3) enzyme recovery and production cost and (4) potential utilization of xylose. Significant cost reduction appears possible through further research in these directions.

Annual report 1997. Energies and raw materials; Rapport annuel 1997. Energies et matieres premieres

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

Influence of stabilizer on the environment and their use as possible secondary raw material

International Nuclear Information System (INIS)

Jelenova, M.

2001-01-01

In this paper author deals with the environmental impact of coal combustion in coal fired power plants and with influence of ash and stabilizer on the environment and their use as possible secondary raw material

Annual report 1997. Energies and raw materials; Rapport annuel 1997. Energies et matieres premieres

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)

Farmers as providers of raw materials and energy. Proceedings; Der Landwirt als Energie- und Rohstoffwirt. Konferenzbeitraege

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Within the 10th EUROSOLAR conference at 14th to 15th April, 2008, at Leipzig (Federal Republic of Germany), the following lectures were held: (a) Bioenergy in the Federal Republic of Germany: Potentials, state of the art and perspectives (M. Kaltschmitt, V. Lenz, D. Thraen); (b) Chances and risks of the energy production from biomass in rural area (G. Thalheim); (c) To the compatibility of utilizing bio energy and environmental preservation (K. Mueschen); (d) Biorefinery systems - industrial material use of regenerative raw materials (B. Kamm); (e) Agriculturists and forestry experts as producers of raw material - current risks and new chances (H. Fischer); (f) Potentials of the improvement of productivity by means of an expansion of options of useful plants (K. Goedeke); (g) Farmers as providers of energy and raw materials (H. Loick); (h) Problems and challenges of the utilization of biomass (P. Volkmer); (i) Energetic recycling management (G. Mehler); (j) Pure fuels instead of fuel mixtures - The farmer as providers of energy and raw materials (P. Schrum); (k) Feed and distribution of bio-natural gas from the view of a regional provider (J. Horn); (l) Biogasification and feed into natural gas networks - by the example of BGA Darmstadt-Wixhausen (M. Schlegel); (m) The right framework for the feed of bio methane into natural gas nets (S. Reichelt); (n) Virtual power plants - Efficient option of the local energy production (G. Weissmueller); (o) The role of bio energy in the power mix renewable energies (R. Bischof); (p) The autonomous power supply - from the bio energy village to the autonomous solar energy village (K. Scheffer); (q) Bio energy villages at the Lake Constance - Model projects for the rural area (B. Mueller); (r) Bio energy region Mureck / Steiermark (K. Totter); (s) The bio energy in the current German legislation process (H.-J. Fell).

Natural stone muds as secondary raw materials: towards a new sustainable recovery process

Science.gov (United States)

Zichella, Lorena; Tori, Alice; Bellopede, Rossana; Marini, Paola

2016-04-01

The production of residual sludge is a topical issue, and has become essential to recover and reuse the materials, both for the economics and the environmental aspect. According to environmental EU Directives, in fact ,the stone cutting and processing should characterized by following objectives, targets and actions: the reduction of waste generated, the decreasing of use of critical raw material, the zero landfilling of sludge and decreasing in potential soil contamination, the prevention of transport of dangerous waste, the reduction of energy consumption, the zero impact on air pollution and the cost reduction . There are many industrial sector in which residual sludge have high concentrations of metals and/or elements deemed harmful and therefore hazardous waste. An important goal, for all industrial sectors, is an increase in productivity and a parallel reduction in costs. The research leads to the development of solutions with an always reduced environmental impact. The possibility to decrease the amount of required raw materials and at the same time the reduction in the amount of waste has become the aim for any industrial reality. From literature there are different approaches for the recovery of raw and secondary materials, and are often used for the purpose chemical products that separate the elements constituting the mud but at the same time make additional pollutants. The aim of the study is to find solutions that are environmentally sustainable for both industries and citizens. The present study is focused on three different Piedmont rocks: Luserna, Diorite from Traversella and Diorite from Vico, processed with three different stone machining technologies: cutting with diamond wire in quarry (blocks), in sawmill (slabs) and surface polishing. The steps are: chemical analysis, particle size analysis and mineralogical composition and characterization of the sludge obtained from the various machining operations for the recovery of the metal material by

Utilization of raw material from early thinnings; Ensiharvennuspuun hyoedyntaeminen

Energy Technology Data Exchange (ETDEWEB)

Alen, R; Marttina, M; Toivanen, J [Jyvaeskylae Univ. (Finland). Dept. of Chemistry

1997-12-01

Wood material from early thinnings is one of the most potential new material reserves (4 - 6 million m{sup 3}) for industrial purposes. However, the prerequisites for an enhanced utilisation of this reserve would be, besides more efficient logging, debarking, and chipping, an optimal fractionation of wood material into energy and fibre production. The aim of this project was to promote the use of first-thinning wood as a competitive raw material for energy production by increasing the potential utilisation of the corresponding wood resource for chemical pulping. During the year 1996 the variation of fibre length distribution within the stem and top (total height of 12 m) of a 27-years-old pine wood (Pinus sylvestris) was determined. Tentative calculations indicated that about 67 % of the wood dry matter consists of fibres having an average fibre length more than 2 mm. It was considered that most of this fraction with high quality fibre properties could be recovered and used for pulping. In addition, the detailed FTIR analysis of different samples from the same pine wood showed that there was an adequate correlation between the FTIR spectrometric data and the fibre length averages. (orig.)

The Influence of the Fruits Addition on the Quality Characteristics of Yogurt

Directory of Open Access Journals (Sweden)

Zorica Vosgan

2016-10-01

Full Text Available Yogurt is considered a healthy food and by incorporating fruits the flavor and its nutritional value are improved. The objective of this study consists in obtaining and characterization of functional dairy products with added fruits, of yogurt type. The raw material used for obtaining the acid dairy products is cow milk, in which there were incorporated fruits: cherry, bananas and oleaginous fruits (nuts. The evolution in time of the acidity during fermentation is influenced by the addition of fruits, the highest acidity being reported in the cherry yogurt case. The ascorbic acid content of the fruity yogurts almost doubled compared to simple yogurt, the highest content of vitamin C was found in the yogurt with bananas. The amount of fat was higher in the yogurt containing nuts, because of the oleaginous fruits contribution, fact observed also due to a lower amount of whey released, followed by the yogurt with banana and the cherry yogurt, which released more whey. The study results also indicated that fruits have the effect of increasing the number of lactic acid bacteria, especially the cherry yogurt leading to a population of 4.84 ± 0.13 log CFU/ml.

New raw materials improve packing sealing efficiency

International Nuclear Information System (INIS)

Igel, B.; McKeague, L.

2012-01-01

End-users and OEM's using or manufacturing on/off and control valves expect a permanent and effective increase in service life together with an increased sealing capability while at the same time minimizing maintenance concerns. Developing materials which provide consistency and repeatability are essential characteristics to optimizing valve performance. “New Generation” materials and yarn allow us to meet this growing demand while complying with the requirements related to chemical purity and an increased level of safety to both plant workers and equipment in the nuclear environment. Through R&D initiatives and developments in new and improved raw materials; a new mechanical packing generation which optimizes friction coefficients and extended life cycle has been introduced to the industry. Lower friction values drastically optimize actuator effort and size improving efficiency for stem operation with significant improvements in flow control of fluids. Combined with new and improved procedures (installation, torque levels and consolidation recommendations), this new packing generation has provided significant improvement in the mechanical behavior of packing materials (independent tests carried out in collaboration with AECL and CETIM) this has provided the opportunity to develop successful Valve Enhancement Programs which offer improved efficiency, valve operation and repeatability. These NEW generation yarns are available with or without wire reinforcement depending on specific operating parameters and conditions. The purpose of this presentation is to demonstrate that new generation material(s). Which are available to the industry for AOV, MOV and Manual valves? - To highlight the steps taken in R&D and manufacturing contributing to the much improved yarns and finished packing products. - Comply and are designed to meet the stringent requirements in the nuclear industry - Simplify valve maintenance without risk to safety or performance - Increase service

Self-compacting paste system using secondary raw materials

International Nuclear Information System (INIS)

Rizwan, S.A.

2008-01-01

A study has been carried out on self-compacting paste (SCP) systems using various cements and secondary raw materials (SRM's) including rice husk ash (RHA) and Silica Fume (SF). These systems were characterized by: SRM particle size, powder water demand (WD) and setting times, flow, strength, microstructure and early volume stability. The result show that WD increased by adding SRM's due to their smaller particle size, higher surface area and internal porosity. Inclusion of SRM's in SCP systems as cement replacements also increase strength of SCP systems due to filler, hydration and pozzolanic actions which translate into pore refinement. It is demonstrated that the resultant properties of self-compacting cementitious. System (SCCS) depend upon the nature of SRM used. (author)

Analysis of Cement as Raw Material Inventory on Ready Mix Production Unit at PT. Perdana Beton in Samarinda

OpenAIRE

Wahyuni, Novita Eka

2014-01-01

This study aims to identify and analyze the optimal amount of cement supplies in PT. Perdana Beton In Samarinda. Formulation of the problem in this study is whether the supply of cement as raw material for Ready Mix at PT. Perdana Beton In Samarinda already minimizing the cost of inventory cement. The hypothesis in this study is: '' Allegedly cement as raw material supplies ready mix at PT. Perdana Beton In Samarinda not provide minimum inventory costs'. Basic...

Cross-laminated timber made of Hungarian raw materials

Science.gov (United States)

Marko, G.; Bejo, L.; Takats, P.

2016-04-01

Cross-laminated timber (CLT), generally made out of softwood, enjoys increasing popularity throughout Europe. This material offers a versatile, eco-friendly technology to create strong, lightweight and energy-efficient buildings. Unfortunately, the sites and climatic conditions in Hungary are not suitable for growing high-quality coniferous trees. Transporting raw materials from other countries (sometimes thousands of kilometres away) negates the environmental advantages of wood-based construction. Local options are definitely preferable from an ecological aspect. Poplar wood (populus spp.) is of great economic importance in Hungary. There are several relatively high density, high strength varieties growing in large quantities in Hungary, that may be used as alternatives to softwood, with comparable properties. There is an increasing interest in using poplar as a construction material, especially in regions were there is a shortage of traditional construction timber. This paper presents the results of a preliminary investigation to create CLT using poplar lumber. Laboratory-scale CLT specimens were created in a hot press, and tested for their loadbearing capacity. The MOR values of poplar CLT are comparable to, albeit somewhat lowerthan those of softwood CLT. Further investigations are required to establish the economic viability and technological conditions for the commercial production of poplar CLT.

Indicators for the use of raw materials in the context of sustainable development in Germany; Indikatoren/Kennzahlen fuer den Rohstoffverbrauch im Rahmen der Nachhaltigkeitsdiskussion

Energy Technology Data Exchange (ETDEWEB)

Giegrich, Juergen; Liebich, Axel; Lauwigi, Christoph; Reinhardt, Joachim [ifeu-Institut fuer Energie- und Umweltforschung GmbH, Heidelberg (Germany)

2012-01-15

Raw material productivity is a key indicator in the German strategy for sustainable development located in the chapter about ''conservation of resources''. Raw material productivity relates the gross domestic product (GDP) to the sum of domestically extracted abiotic raw materials and imported abiotic raw materials, semi-finished products and finished products. The main objective of this research project was to further develop or supplement this existing indicator. First of all the basic concepts of ''natural resource'' and ''raw material'' was clearly defined and put into the context of existing resource strategies. The broad concept of natural resource was adopted and six types of natural resources were identified (raw material, energy, water, land, biodiversity and the sink function of environmental media) Headline indicators were suggested for each of them. An aggregated indicator was developed and discussed which was called Environmental Impact Load (EVIL). The pressures represented by four resource indicators and four environmental indicators for the sink function were calculated for all imported goods with the help of 130 resource and environmental profiles and the German import statistics of the year 2005. This step was necessary to resolve the asymmetric approach of calculating the pressures caused by imports and domestic production and consumption. The ''rucksacks'' of the imports were accounted with domestic figures and the export ''rucksacks''. The raw material demand of imported goods expressed in raw material equivalent was derived to be twice as high as the domestic material extraction. Finally the function of the different resource indicators to represent each other was tested with the help of correlations. As a first approximation a certain correlation exists between some indicators. But it is recommended that each resource indicator should be kept

Towards a dynamic assessment of raw materials criticality: linking agent-based demand--with material flow supply modelling approaches.

Science.gov (United States)

Knoeri, Christof; Wäger, Patrick A; Stamp, Anna; Althaus, Hans-Joerg; Weil, Marcel

2013-09-01

Emerging technologies such as information and communication-, photovoltaic- or battery technologies are expected to increase significantly the demand for scarce metals in the near future. The recently developed methods to evaluate the criticality of mineral raw materials typically provide a 'snapshot' of the criticality of a certain material at one point in time by using static indicators both for supply risk and for the impacts of supply restrictions. While allowing for insights into the mechanisms behind the criticality of raw materials, these methods cannot account for dynamic changes in products and/or activities over time. In this paper we propose a conceptual framework intended to overcome these limitations by including the dynamic interactions between different possible demand and supply configurations. The framework integrates an agent-based behaviour model, where demand emerges from individual agent decisions and interaction, into a dynamic material flow model, representing the materials' stocks and flows. Within the framework, the environmental implications of substitution decisions are evaluated by applying life-cycle assessment methodology. The approach makes a first step towards a dynamic criticality assessment and will enhance the understanding of industrial substitution decisions and environmental implications related to critical metals. We discuss the potential and limitation of such an approach in contrast to state-of-the-art methods and how it might lead to criticality assessments tailored to the specific circumstances of single industrial sectors or individual companies. Copyright © 2013 Elsevier B.V. All rights reserved.

Energy and raw material potentials of wood residue in the Pacific Coast States: a summary of a preliminary feasibility investigation.

Science.gov (United States)

John B. Grantham; Eldon Estep; John M. Pierovich; Harold Tarkow; Thomas C. Adams

1974-01-01

Results are reported of a preliminary investigation of feasibility of using wood residue to meet energy and raw material needs in the Pacific Coast States. Magnitude of needs was examined and volume of logging-residue and unused mill residue was estimated. Costs of obtaining and preprocessing logging residue for energy and pulp and particle board raw material were...

Assessing raw materials for carbon black production using 1H- and 13C-nuclear magnetic resonance

International Nuclear Information System (INIS)

Bekarek, V.; Meic, Z.

1980-01-01

1 H and 13 C NMR spectroscopy in combination with elemental analysis and/or infrared spetroscopy were used in evaluating raw materials for the preparation of carbon black. Three models and seven industrial mixtures were analysed. The evaluation of experimental results by the Brown-Ladner method yielded information on the basic chemical characteristics of the raw material, ie., the contents of carbon and other elements, the contents of aromatic and aliphatic components and the nature of the aromatic compounds present. The obtained results are in good agreement with theoretical results for the model mixtures and with results of gas chromatography for the industrial mixtures

Study of the incorporation of marble and granite wastes in the raw material to produce glass wool

International Nuclear Information System (INIS)

Rodrigues, Girley Ferreira; Junca, Eduardo; Telles, Victor Bridi; Espinosa, Denise Crocce Romano; Tenorio, Jorge Alberto Soares; Alves, Joner Oliveira

2010-01-01

The study aimed to characterize materials obtained from the melted mixture containing marble and granite wastes, and also chemical reagents. Using the characterization results was defined the feasibility of reuse of the marble and granite wastes, through the incorporation in the raw material to produce glass wool (a material with great consumer market as thermo-acoustic insulator). The batch was poured in a water-filled recipient and also in a Herty viscometer at temperatures of 1400, 1450 and 1500 °C. Samples of produced materials were characterized by morphology using Scanning Electron Microscopy, by atomic structure using X-ray Diffraction, and by thermal behavior using Differential Thermal Analysis. The total amount of marble and granite wastes can reach about 79% replacement in relation to the total weight of the raw material used in the glass wool production. (author)

NAA study on characteristics and sources of raw materials of celadon bodies from Qingliangsi kiln and Zhanggongxiang kiln

International Nuclear Information System (INIS)

Wu Zhanjun; Zhao Weijuan; Lu Xiaoke; Li Guoxia; Guo Min; Xie Jianzhong; Qiu Xia; Feng Songlin

2007-01-01

Thirty-seven samples of ancient Chinese Ru porcelain bodies unearthed from Qingliangsi kiln (containing 32 Ru official porcelain bodies and 5 Ru folk porcelain bodies), thirty-two samples of ancient celadon bodies from Zhanggongxiang kiln, and fourteen samples of modern mineral, were selected and analyzed by neutron activation analysis (NAA) method. Twenty-three elements were measured. The data of these elemental contents were processed by scatter analysis and principle component analysis methods in order to determine the characteristics and sources of the raw materials of the celadon porcelain bodies from the foregoing two kilns. The results show that Fe, Ce, Ba, Ta, Th, La, Sm and Cr are the fingerprint elements to distinguish the ancient Ru official porcelain bodies from ancient celadon bodies of Zhanggongxiang kiln. The sources of the raw material of the ancient Ru official porcelain bodies from Qingliangsi kiln are more concentrated and stable than those from Zhanggongxiang kiln. The Ru folk porcelain bodies and the Ru official porcelain bodies from Qingliangsi kiln have the same provenance, both sources of which are local. The raw material origins of the ancient celadon bodies from Zhanggongxiang kiln is a little dispersed and the compositions of the raw material are different from the Ru porcelains, but the distance is not far away from each other. (authors)

Mining Pribram in science and technology. Proceedings of Session U - Mineral raw materials treatment

International Nuclear Information System (INIS)

Tomasek, J.; Vetejska, K.

1987-01-01

The proceedings of session ''Mineral raw materials treatment'' contain 27 papers of which only one deals with the application of nuclear technology, namely, the effect of fast electrons on the magnetic properties of the polymetallic Rudniany ore. (J.B.)

Effects of gamma irradiation on raw materials and perfumes

International Nuclear Information System (INIS)

Guillot, M.; Pelpel, A.

1983-01-01

In order to enlight the strange problem of apparent perfume stability observed in manufactured talc powders sterilized by gamma rays, investigations were made on samples of odorant substances (raw materials, essential oils, or elaborated mixtures). As a rule, no immediate adulteration of olfactive caracteristics resulted at once from gamma irradiation. In several cases, a stabilizing effect appeared immediately and remained effective after long storage in various conditions (of temperature, or light, or oxygen exposure). This unexpected effect seems to be in accordance with previous experiments on gamma or electron irradiations of mixtures of organic molecules, reported in litterature: a mutual inhibition was observed to take place [fr

Raw materials for advanced ceramics: rare earths separation processes

International Nuclear Information System (INIS)

Ricci, D.R.; Nobre, J.S.M.; Paschoal, J.O.A.

1990-01-01

The importance of obtaining purified rare earths oxidesis related, mainly to the increasing use of these compounds as raw materials for advanced ceramics. Processes of rare earths separation and purification are almost always based on the solvent extraction, fractional precipitation and ion exchange chromatography techniques, whose association depends on the initial concentrate and on the desired purity. This paper describes some steps of fractionation of didymium carbonate by using the solvent extraction and fractional precipitation techniques. The experimental conditions presented here have enable the production of lantanium, neodimium - praseodimium, samarium - gadolinium and ytrium concentrates, which constitute the intermediate fractions of the overall process to obtain high purity rare earths. (author) [pt

Markisa fruit (Passiflora edulis var. flavicarpa) as a fixation material of natural colour of mangrove waste on batik

Science.gov (United States)

Izzah, S. N.; Marwoto, P.; Iswari, R. S.

2018-03-01

The process of natural colouring of batik using mangrove waste with the markisa fruit as a fixation material has been reported. In this experiment, the fixation material of markisa fruit has been compared with the commonly used fixation materials, such as CaCO3, AlK(SO4)2, and FeSO4 as material controls. Both grey scale and staining scale have been used as standard evaluations. Based on the Indonesian National Standard (SNI) it can be shown that batik with markisa fruit as a fixation material has a colour fastness value against average washing at good-excellent level (4-5) and colour fastness value to sunshine is moderate-excellent level (3-5). Thus, we conclude that Markisa fruit can be used as a fixation material in the colouring process of natural colour batik from mangrove waste.

Raw materials and energy - effects of globalization on the safety of German's supply sufficiency; Rohstoffe und Energie. Auswirkungen der Globalisierung auf die Versorgungssicherheit Deutschlands

Energy Technology Data Exchange (ETDEWEB)

Wellmer, F.W. [Technische Univ. Berlin (Germany)

2001-07-01

Raw material deposits are not mobile, so globalisation has always been an important element of raw materials production and trade. Raw materials production and transport should be regarded as a large-scale system. Lower freight rates have made overseas transport possible even for bulk raw materials. If we look at Germany's raw materials supply, we find that we are customers buying from the whole world. [German] Da Lagerstaetten ortsgebunden sind, ist Globalisierung seit jeher ein wesentliches Element von Rohstoffgewinnung und handel. Rohstoffgewinnung und Transportmoeglichkeiten muessen als Grosssystem betrachtet werden. Nicht zuletzt wegen der gesunkenen Frachtraten ist der ueberseeische Transport heute selbst fuer Massenrohstoffe moeglich geworden. Betrachtet man die Rohstoffversorgung Deutschlands, wird deutlich, dass wir Kunde der ganzen Welt sind. (orig.)

DEVELOPMENT OF METHOD OF QUALITATIVE ANALYSIS OF BIRD CHERRY FRUIT FOR INCLUSION IN THE MONOGRAPH OF STATE PHARMACOPOEIA OF UKRAINE

Directory of Open Access Journals (Sweden)

Lenchyk L.V.

2016-06-01

Full Text Available Introduction. Bird cherry Padus avium Mill, Rosaceae, is widespread in Ukraine, especially in forests and forest-steppe areas. Bird cherry fruits have long been used in medicine and is a valuable medicinal raw materials. They stated to posess astringent, anti-inflammatory, phytoncidal properties. Bird cherry fruits are included in the USSR Pharmacopoeia IX ed., The State Pharmacopoeia of the Russian Federation, The State Pharmacopoeia of Republic of Belarus. In Ukraine there are no contemporary normative documents for this medicinal plant material, therefore it is the actual to develop projects in the national monographs "dry bird cherry fruit" and "fresh bird cherry fruit" to be included in the State Pharmacopoeia of Ukraine. According to European Pharmacopoeia recommendation method of thin-layer chromatography (TLC is prescribed only for the identification of the herbal drug. The principles of thin-layer chromatography and application of the technique in pharmaceutical analysis are described in State Pharmacopoeia of Ukraine. As it is effective and easy to perform, and the equipment required is inexpensive, the technique is frequently used for evaluating medicinal plant materials and their preparations. The TLC is aimed at elucidating the chromatogram of the drug with respect to selected reference compounds that are described for inclusion as reagents. Aim of this study was to develop methods of qualitative analysis of bird cherry fruits for a monograph in the State Pharmacopoeia of Ukraine (SPU. Materials and Methods. The object of our study was dried bird cherry fruits (7 samples and fresh bird cherry fruits (7 samples harvested in 2013-2015 in Kharkiv, Poltava, Luhansk, Sumy, Lviv, Mykolaiv regions and the city Mariupol. Samples were registered in the department of SPU State Enterprise "Pharmacopeia center". In accordance with the Ph. Eur. and SPU requirements in "identification C" determination was performed by TLC. TLC was performed on

Melting behaviour of raw materials and recycled stone wool waste

DEFF Research Database (Denmark)

Schultz-Falk, Vickie; Agersted, Karsten; Jensen, Peter Arendt

2018-01-01

Stone wool is a widely used material for building insulation, to provide thermal comfort along with fire stability and acoustic comfort for all types of buildings. Stone wool waste generated either during production or during renovation or demolition of buildings can be recycled back into the sto...... wool melt production. This study investigates and compares the thermal response and melting behaviour of a conventional stone wool charge and stone wool waste. The study combines differential scanning calorimetry (DSC), hot stage microscopy (HSM) and X-ray diffraction (XRD). DSC reveals...... that the conventional charge and stone wool waste have fundamentally different thermal responses, where the charge experiences gas release, phase transition and melting of the individual raw materials. The stone wool waste experiences glass transition, crystallization and finally melting. Both DSC and HSM measurements...

On the increasing multifunctionality of agricultural raw materials: three dilemmas for innovation and adoption

NARCIS (Netherlands)

Boehlje, M.; Bröring, S.

2010-01-01

The agricultural sector is increasingly becoming multifunctional. It is the entry point of several value chains. Agricultural raw materials are increasingly being used for multiple industries or sectors beyond the traditional fiber and nutrition industries—energy in the form of ethanol and

Conception for the protection of mineable raw materials in the Land of Brandenburg (Germany)

International Nuclear Information System (INIS)

Kopf, M.

1995-01-01

The pit and quarry industry in Brandenburg will within a few years the same importance as the lignite industry. Both industries together may have up to 20 000 employees beyond the year 2000. The same number of employees could result in the enterprises of local and other subcontractors and mine suppliers. The government of Brandenburg creates at present the legal prerequisites to secure the supply with mineable raw materials. The regulation of the protection of mineable raw materials is proposed to be realised within the scope of the second plan for the development of the country, and within the regional plannings. The protection of the basic conditions for mining industries is a permanent task for administration and politics. By encouraged engagement in the case of opposed interests, those of mining can be considered with acceptable results provided the parties are ready to compromise. (orig.) [de

The use of rapid spectroscopic screening methods to detect adulteration of food raw materials and ingredients

DEFF Research Database (Denmark)

Sørensen, Klavs Martin; Khakimov, Bekzod; Engelsen, Søren Balling

2016-01-01

with chemometrics appears to be an efficient first choice for testing incoming raw materials and ingredients in the food production. However, in order to realize its full potential, it is necessary to move away from the current thoughts at the Parnassus, namely the targeted approach. This review will focus......International trade in food commodities will continue to increase and the complex food supply chains make adulteration detection and traceability a technical, logistical and financial challenge. There is no magic solution for adulteration testing, but NIR spectroscopy in combination...... on the exploitation of the capability of NIR spectroscopy to fingerprint incoming raw materials and ingredients as an integrated part of the industry's self-monitoring program typically called process analytical technology....

EFFECT OF NON-TRADITIONAL VEGETABLE RAW MATERIALS ON THE PROPERTIES AND BIOTECHNOLOGICAL STRUCTURE PASTRY

Directory of Open Access Journals (Sweden)

Y. P. Kolomnikova

2015-01-01

Full Text Available Summary. An important task is the use of catering in the preparation of food products of new types of raw materials, which can solve the problem of nutrition. One way to improve the quality and range of flour culinary products is the use of technology in their enriching additives plant. Among them are a subgroup of additives derived from cereals, pulses, oilseeds, vegetables, fruit and other plant materials. As a result of researches the technology buns bakery products with the addition of oil and meal of wheat germ, pumpkin seed oil cake. Wheat germ oil cake is a source of complete protein and biologically active substances, is rich in essential amino acids, unsaturated ω-3, ω-6 fatty acids, vitamin E, D, B1, B2, B6, PP, pantothenic and folic acid, carotenoids. The composition of pumpkin seed oil cake include essential oils, phytosterols, resinous substances, organic acids, vitamins C and B, carotenoids, carbohydrate melen. In the composition of wheat germ oil contains: all essential, not synthesized by the human amino acid (tryptophan, methionine, leucine, valine, isoleucine, polyunsaturated fatty acids (ω-3, ω-6 and ω-9 acid, a large amount of vitamins, micro - and macronutrients. In the development of the experimental basis for the formulation chosen butter bakery products, in which part of the wheat flour (20 % was replaced by wheat germ oil cake (10 % and pumpkin seed oil cake (10 %. Margarine in the classical formulation was replaced by wheat germ oil, sugar - on natural honey. Insertion additives significantly improve the properties of biotech pastry. The proposed method of production of buns bakery products can reduce the duration of the production process, to intensify the process of gas formation in the test to increase gas-retaining capacity and lift test.

Characterization of raw materials and manufactured binderless particleboard from oil palm biomass

International Nuclear Information System (INIS)

Hashim, Rokiah; Nadhari, Wan Noor Aidawati Wan; Sulaiman, Othman; Kawamura, Fumio; Hiziroglu, Salim; Sato, Masatoshi; Sugimoto, Tomoko; Seng, Tay Guan; Tanaka, Ryohei

2011-01-01

The objective of this study was to examine the extractive, holocellulose, alpha cellulose, lignin, starch, and sugar contents of oil palm biomass and to evaluate its suitability in binderless particleboard production. In this study, bark, leaves, fronds, mid-parts and core-parts of the trunks were used to produce experimental binderless particleboard panels. Binderless particleboard panels were made with a target density of 0.80 g/cm 3 at a temperature of 180 o C and a pressure of 12 MPa in a computer controlled hot press. The modulus of rupture, the internal bond strength, the thickness swelling and the water absorption of the panels were evaluated. Fourier transform infrared spectroscopy and field emission scanning electron microscopy were used to characterize the properties of the raw materials and the manufactured panels. The chemical composition of the oil palm biomass consisted of high holocellulose, lignin, starch and sugar contents that have been found to aid in the production of binderless particleboard. The core-part of the trunk contained the highest amount of starch and total sugar. Samples made from the core-parts and fronds had sufficient modulus of rupture and internal bond strength to meet the Japanese Industrial Standard. The internal bond strength of the mid-part panels also met the standard. However, binderless board prepared from bark and leaves showed poor modulus of rupture and internal bond strength. Samples from the core-parts had the lowest thickness swell and water absorption but did not meet the above standard. The Fourier transform infrared spectroscopy spectra did not show any substantial difference between the raw materials and the manufactured panels. Field emission scanning electron microscopy indicated that the compressed cells varied between raw material types and showed the presence of compressed cells with some starch granules that facilitated adhesion. Based on the findings of this study, oil palm has the potential to be used to

Nutritional Evaluation of Raw Materials Entering the Structure to Mixed Fodder for the Specie Poecilia reticulata (Guppy

Directory of Open Access Journals (Sweden)

Adrian Gruber

2011-05-01

Full Text Available In the ornamental pisciculture is a especial emphasis on the exterior shape and color to the fishes, issues that are dependent directly to the structure of compound feeds in relation to the nutritional characteristics of the raw materials.Own research or focused on analyzing the crude chemical composition with Weende scheme (water content and dry matter, crude ash, crude protein, crude fat, crude fiber, SEN of raw materials can be used in the structure of a compound feeds for the Poecilia reticulata (guppy species, for most of these materials there are no current data in the literature.These materials were analyzed: gelatin, wheat flour, sunflower meal, soybean meal, meal Spirulina platensis, carrot (Daucus carota, Pangasius fillet, Daphnia pulex, grount dandelion (Taraxacum officinale, grount nettle (Urtica dioica and yeast.

Rehydration properties of hybrid method dried fruit enriched by natural components

Science.gov (United States)

Kowalska, Hanna; Marzec, Agata; Kowalska, Jolanta; Ciurzyńska, Agnieszka; Samborska, Kinga; Bialik, Michał; Lenart, Andrzej

2018-04-01

The aim of the study was to determine the impact of osmotic pre-dehydration and drying of fruit on the rehydration properties of dried fruit. Herein, the effect of fruit juice, applied as a natural enriching substance was very important. In addition, the properties of dried fruits obtained through combined air-drying and subsequent microwave-vacuum drying with `puffing' effect were similar to the freeze-dried fruits, but showed other rehydration properties. As raw material, frozen strawberry (Honeoye variety) and fresh apples (Idared variety) were used in the study. The apples and partially defrosted strawberries were prior dehydrated in solutions of sucrose and a mixture of sucrose with chokeberry juice concentrate at 50°C for 2 h. Next, the fruit samples were dried by one of two ways: air-drying (50°C, 5 h) and microwavevacuum drying for about 360 s; and freeze-drying (30°C, 63 Pa, 24 h). The rehydration was carried out in distilled water (20°C, 5 h). The osmotic pre-dehydration hindered fruit drying process. The impact of drying method became particularly evident while examining the kinetics of rehydration. During the rehydration of the pre-dehydrated dried fruit a slower hydration could be observed. Freeze-dried strawberries absorbed 2-3 times more water than those dried by the `puffing' effect.

Mineral composition of fruit by-products evaluated by neutron activation analysis

International Nuclear Information System (INIS)

Gabriela de Matuoka e Chiocchetti; Nadai Fernandes de, E.A.; Macio Arruda Bacchi; Rogerio Augusto Pazim; Silvana Regina Vicino Sarries; Thais Melega Tome

2013-01-01

Brazil is one of the largest producers of fruits cropping 40 million tons per year. In agro-food processing, approximately 50 % of raw material is discarded generating large amounts of by-products. The lack of information on the nutritional quality of agroindustrial by-products precludes their potential use in the manufacture of food products accessible to all. In this context, the objective of this work was to investigate the nutritional quality of by-products of the industrial processing of fruits. Samples of bagasse, peel and seeds of several fruits (banana, camu camu, coconut, cupuacu, guava, jackfruit, mango, orange, papaya, pineapple, and soursop) were analysed by neutron activation analysis for the determination of Br, Ca, Co, Cr, Cs, Fe, K, La, Na, Rb, Sc and Zn. In general, higher levels of minerals were found in the by-products rather than in the pulps of fruits. This indicates that the use of the by-products should be encouraged, thereby reducing the economic and environmental impact of waste generated by agroindustrial processing. (author)

Inactivation of Listeria monocytogenes in raw fruits by enterocin AS-48.

Science.gov (United States)

Molinos, Antonio Cobo; Abriouel, Hikmate; Ben Omar, Nabil; Lucas, Rosario; Valdivia, Eva; Gálvez, Antonio

2008-12-01

The purpose of this study was to determine the effect of enterocin AS-48 on Listeria monocytogenes CECT 4032 in fruits and fruit juice. Fruits were contaminated with a L. monocytogenes cell suspension, washed with enterocin AS-48 (25 microg/ml) or with sterile distilled water as control, and stored at different temperatures (-20, 6, 15, 22 degrees C). Washing treatments significantly inhibited or completely inactivated L. monocytogenes in strawberries, raspberries, and blackberries stored at 15 and 22 degrees C for up to 2 days and in blackberries and strawberries at 6 degrees C for up to 7 days. Washing treatments with enterocin AS-48 also reduced viable counts in sliced melon, watermelon, pear, and kiwi but did not avoid proliferation of survivors during storage at 15 and 22 degrees C. Added enterocin (25 microg/ml) completely inactivated L. monocytogenes in watermelon juice within 24 h. To enhance the antilisterial activity of treatments, enterocin AS-48 was tested in combination with other antimicrobial substances on sliced melon stored at 22 degrees C. The combinations of enterocin AS-48 and trisodium trimetaphosphate, sodium lactate, lactic acid, polyphosphoric acid, carvacrol, hydrocinnamic acid, p-hydroxybenzoic acid, n-propyl p-hydroxybenzoate, or 2-nitropropanol showed increased antilisterial activities compared with each antimicrobial tested separately. Washing treatments with enterocin AS-48 in combination with 12 mM carvacrol, as well as with 100 mM n-propyl p-hydroxybenzoate, avoided regrowth of Listeria during storage at 22 degrees C. Results from this study indicate that enterocin AS-48 alone or in combination with other preservatives could serve as an additional hurdle against L. monocytogenes in fruits and fruit juices.

Hydrolysis technology for producing sugars from biomass as raw material for the chemical industry - SugarTech

Energy Technology Data Exchange (ETDEWEB)

Kallioinen, A.; Haekkinen, M.; Pakula, T. (and others) (VTT Technical Research Centre of Finland, Espoo (Finland)), Email: anne.kallioinen@vtt.fi

2010-10-15

In SugarTech project, spruce, forest residue, birch and sugar cane bagasse have been studied as a raw material for production of sugars to be processed further to ethanol and other chemicals. These raw materials containing high proportion of carbohydrates have been analysed and pretreated for enzyme hydrolysis by steam explosion and oxidative methods. The pretreated materials have been studied in respect to yield and enzymatic hydrolysability. Birch and bagasse could easily be pretreated with steam explosion. Catalytic and alkaline oxidation treatment of spruce produced material with superior hydrolysability to steam exploded material. Enzyme adsorption and desorption were studied with lignocellulosic substrates aiming at recycling of enzymes in the hydrolysis process. After enzymatic hydrolysis, a major part of the enzymes remained bound to substrate in spite of high degree of hydrolysis. Desorption of enzymes could be detected only with catalytically oxidised spruce. In addition, the hydrolytic system of Trichoderma reesei, which is a widely used fungus for cellulase enzyme production, has been studied in the presence of different substrates. The substrate and the pretreatment method had clear effects on gene expression profile. (orig.)

EVALUATION OF THERMAL EFFICIENCY OF THE TECHNOLOGICAL SCHEME OF APPLE CHIPS AND DRIED FRUITS PRODUCTION

Directory of Open Access Journals (Sweden)

G. V. Kalashnikov

2014-01-01

Full Text Available The estimation of thermodynamic perfection of separate technological processes is executed at heat-moisture of handling of fruit and a line of manufacture of fruit apple chips and dried fruits. The technological scheme of a line of processing of fruits and manufactures of fruit chips on the basis of convection and the microwave-dryings suggested resource-saving. The technique is made and results of calculation of thermal expenses for various schemes of manufacture of apple chips are resulted. For the offered scheme material, thermal and power streams on the basis of balance parities of technological processes are certain. The comparative thermal production efficiency of apple chips for a base foreign variant and the offered technological scheme with the closed cycle of use of the heat-carrier and the combined convection-microwave-drying is shown. In this paper we define the thermal and energy flows for the processes of convective drying, pre-microwave drying, hydrothermal treatment and final microwave drying plant material, which are one of the main stages of the production of all kinds of fruit and vegetable concentrates, including fruit apple chips. Resource-saving ways moisture-heat of handling (hydration, blanching, drying, etc. produce raw materials in the production of food concentrates suggested a reduced water flow with a high degree of use of its potential power and microwave sources. To assess the thermal efficiency of the various processes and production schemes used as indicators of thermal efficiency and proposed value of specific heat (kJ / kg given mass productivity per unit of feedstock and translational moisture. The values of the mass fraction of the heat of material flows for the base and the proposed resource-saving production scheme fruit chips, for example, apple, based on a combination of convection-microwave drying each control surface.

Raw-materials mixtures from waste of the coal industry for production of ceramic materials

Energy Technology Data Exchange (ETDEWEB)

Galpern, E I [Scientific-Manufacturing Enterprise ` ` Ceramics` ` , Donetsk (Ukraine); Pashchenko, L V [Inst. of Physical, Organic and Coal Chemistry of NASU, Donetsk (Ukraine)

1998-09-01

The liquidation of waste dumps on the surface of mining enterprises and realization of measures by environment protection of air and aquatic basins are connected to the complex processing of mining mass. The main directions of utilization of mining rocks and coal wastes realized in Ukraine industry are: - filling of mines worked-out area by grouting solutions; - ceramic brick, porous filling materials and binding materials production; - road-making, construction of hydrostructures and industrial objects; - output of concrete items predominantly for using in mining conditions. The peculiarity of wastes using in above-mentioned fields is the possibility of their mass application in quantities commensurable with valumes of their yields. The experience of enterprises work which process mining rocks into building materials by burning method (ceramic brick, porous aggregates of concretes as aggloporite, expanded clay aggregate) has shown that unconstant and, as the rule, exceeding norms content of carbon and sulphur in the rock results to deterioration of products quality and technological factors of production. Unstability of carbon content in raw material makes the burning process hardly operated. Obtained products having residual carbon in the view of coke residue are often characterized by lower physical-mechanical characteristics. (orig./SR)

Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

Science.gov (United States)

Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

2011-01-01

The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.

Raw material boom in an industrial country. Rohstoffboom in einem Industrieland

Energy Technology Data Exchange (ETDEWEB)

Enders, K S

1984-01-01

First of all, a theoretical investigation is carried out to discover under which conditions a raw material boom displaces traditional sectors of industry, and which groups win and lose in the process. Subsequently, the peculiarities of the adaption process induced by the boom are analysed. Particular attention is paid to the possibility of transition (short-term) unemployment (Dutch disease). In conclusion, Norway's experiences in the oil and gas boom in the North Sea ar described and then compared with theoretical statements.

Vegan triple-ironman (raw vegetables/fruits).

Science.gov (United States)

Leischik, Roman; Spelsberg, Norman

2014-01-01

Endurance sport requires a healthy and balanced diet. In this case report we present the findings of an ultra-triathlete (three times Ironman, means 11.4 km swim, 540 km bike, 125 km run in 41:18 h as a whole) living on a raw vegan diet and having finished the competitions under these nutritional conditions. To this end, the vegan ultra triathlete and a control group of 10 Ironman triathletes of similar age living on a mixed diet were investigated, using echocardiography and spiroergometry. In addition, blood samples were taken from the vegan athlete both in the sporting season and in the off-season. The vegan athlete showed no signs of dietary deficiencies or impaired health. In comparison with the control group, the vegan athlete showed a higher oxygen intake at the respiratory compensation point. This case demonstrates that even top-class sporting performance, like that of a three-time Ironman, is possible on a vegan diet. Whether a vegan diet offers advantages or disadvantages for the performance of endurance athletes remains an open question.

Vegan Triple-Ironman (Raw Vegetables/Fruits

Directory of Open Access Journals (Sweden)

Roman Leischik

2014-01-01

Full Text Available Endurance sport requires a healthy and balanced diet. In this case report we present the findings of an ultra-triathlete (three times Ironman, means 11.4 km swim, 540 km bike, 125 km run in 41:18 h as a whole living on a raw vegan diet and having finished the competitions under these nutritional conditions. To this end, the vegan ultra triathlete and a control group of 10 Ironman triathletes of similar age living on a mixed diet were investigated, using echocardiography and spiroergometry. In addition, blood samples were taken from the vegan athlete both in the sporting season and in the off-season. The vegan athlete showed no signs of dietary deficiencies or impaired health. In comparison with the control group, the vegan athlete showed a higher oxygen intake at the respiratory compensation point. This case demonstrates that even top-class sporting performance, like that of a three-time Ironman, is possible on a vegan diet. Whether a vegan diet offers advantages or disadvantages for the performance of endurance athletes remains an open question.

Vegan Triple-Ironman (Raw Vegetables/Fruits)

Science.gov (United States)

Leischik, Roman; Spelsberg, Norman

2014-01-01

Endurance sport requires a healthy and balanced diet. In this case report we present the findings of an ultra-triathlete (three times Ironman, means 11.4 km swim, 540 km bike, 125 km run in 41:18 h as a whole) living on a raw vegan diet and having finished the competitions under these nutritional conditions. To this end, the vegan ultra triathlete and a control group of 10 Ironman triathletes of similar age living on a mixed diet were investigated, using echocardiography and spiroergometry. In addition, blood samples were taken from the vegan athlete both in the sporting season and in the off-season. The vegan athlete showed no signs of dietary deficiencies or impaired health. In comparison with the control group, the vegan athlete showed a higher oxygen intake at the respiratory compensation point. This case demonstrates that even top-class sporting performance, like that of a three-time Ironman, is possible on a vegan diet. Whether a vegan diet offers advantages or disadvantages for the performance of endurance athletes remains an open question. PMID:24826311

Conditions for new biofuel raw materials. Systems for small scale briquetting and pelletizing; Foerutsaettningar foer nya biobraensleraavaror. System foer smaaskalig brikettering och pelletering

Energy Technology Data Exchange (ETDEWEB)

Paulrud, Susanne; Holmgren, Kristina (The Swedish Environmental Research Institute Ltd., Stockholm (Sweden)); Rosenqvist, Haakan; Boerjesson, Paal (Environmental and Energy Systems Studies, Lund Inst. of Technology, Lund (Sweden))

2009-01-15

The increasing demand for biomass has driven exploitation of the most easily available and cheapest biomass resources such as sawmill waste and logging residues. More knowledge is needed about exploitation and production of potential new biomass resources, currently not used for energy production (or only to a very small extent), in order to meet the future demands from various biomass users. The project aimed to examine the conditions for use of 'new' biomass materials for heat production from technical, economic and other perspectives (price trends, attitudes etc.). More specifically, the study looked at which biomass raw materials have the best characteristics for processing into briquettes and pellets in small-scale production plants (1 000 - 10 000 tonnes fuel produced per year) situated close to the source of the raw material. The study includes a comprehensive analysis of the appropriateness of the different raw materials and a case study including cost estimates for the entire production chain for production of briquettes from reed canary grass on a chosen farm (Laattra gaard). The raw materials judged to have potential to supplement the current biomass range for heat production are willow (and to a certain extent other fast-growing hardwoods), straw and reed canary grass. In the future, other perennial grasses may be of interest. Other forestry products that may help to meet in creasing demand include logging residues, stumps and wood from thinning and precommercial thinning. The study shows that the prerequisites for processing these raw materials into briquettes and pellets in small-scale production plants are relatively good from several aspects (technology, economics, market) but are limited by the types of end user that can use that form of biomass. The study concluded that straw has a low production cost and good prerequisites as a raw material for production of fuel briquettes, fuel pellets and horse bedding pellets. However, use is

Uncertainty analysis in raw material and utility cost of biorefinery synthesis and design

DEFF Research Database (Denmark)

Cheali, Peam; Quaglia, Alberto; Gernaey, Krist

2014-01-01

are characterized by considerable uncertainty. These uncertainties might have significant impact on the results of the design problem, and therefore need to be carefully evaluated and managed, in order to generate candidates for robust design. In this contribution, we study the effect of data uncertainty (raw...... material price and utility cost) on the design of a biorefinery process network....

OPTICAL-ELECTRONIC SYSTEM FOR EXPRESS ANALYSIS OF ORE DRESSABILITY FOR MINERAL RAW MATERIALS BY OPTICAL METHOD

Directory of Open Access Journals (Sweden)

A. A. Alekhin

2013-05-01

Full Text Available The article deals with creation results of experimental prototype of optical-electronic complex, designed to assess ore dressability of mineral raw materials by optical sorting method.

The technological raw material heating furnaces operation efficiency improving issue

Science.gov (United States)

Paramonov, A. M.

2017-08-01

The issue of fuel oil applying efficiency improving in the technological raw material heating furnaces by means of its combustion intensification is considered in the paper. The technical and economic optimization problem of the fuel oil heating before combustion is solved. The fuel oil heating optimal temperature defining method and algorithm analytically considering the correlation of thermal, operating parameters and discounted costs for the heating furnace were developed. The obtained optimization functionality provides the heating furnace appropriate thermal indices achievement at minimum discounted costs. The carried out research results prove the expediency of the proposed solutions using.

Semi-Dried Fruits and Vegetables

Directory of Open Access Journals (Sweden)

Gamze Uysal Seçkin

2015-12-01

Full Text Available Since ancient times, the preservation of fruit and vegetables is an ancient method of drying. Sun drying method has been used more widely. In general, consumer-ready products are dried fruits, while the dried vegetables are the foods subjected to the rehydration processes such as boiling, heating and baking before consumption. In recent years, new products with high eating quality have been attempted to achieve without losing characteristic of raw material. With the improving of food technology, using developed methods (pH reduction with reducing aw, slight heating, preservatives use etc. as protective agent, and using a combination of a low rate as an alternative to traditional food preservation process, products have been obtained without changing original characteristics of food. ‘Semi-dried 'or 'medium moist 'products with little difference between the taste and texture of the product with a damp have gained importance in recent years in terms of consumer preferences. Vegetables or fruits, which have water activity levels between 0.50 and 0.95 and the moisture content of between 26% and 60%, are called 'medium moist fruit or vegetables'. Two different manufacturing process to obtain a semi-dried or intermediate moisture products are applied. First, fully dried fruits and vegetables to be rehydrated with water are brought to the desired level of their moisture content. Second, in the first drying process, when the product moisture content is reduced to the desired level, the drying process is finished. The semi-dried products are preferred by consumers because they have a softer texture in terms of eating quality and like fresh products texture.

Freezing of meat raw materials affects tyramine and diamine accumulation in spontaneously fermented sausages.

Science.gov (United States)

Bover-Cid, Sara; Miguelez-Arrizado, M Jesús; Luz Latorre Moratalla, L; Vidal Carou, M Carmen

2006-01-01

Biogenic amine accumulation was studied in spontaneously fermented sausages (Fuet) manufactured from unfrozen-fresh meat (U-sausages) and frozen-thawed meat (F-sausages). The aim was to investigate whether the frozen storage of raw materials affects the microbial composition and its aminogenic activity during sausage fermentation. Tyramine was the major amine in all sausages. Although the final levels were similar, tyramine accumulated more rapidly in F-sausages, which contained putrescine as the second amine. By contrast, U-sausages accumulated much more cadaverine than putrescine. F-sausages showed a slightly lower pH and free amino acid content as well as higher counts of technological flora (lactic acid and gram positive catalase positive bacteria) and lower counts of enterobacteria. Therefore, to freeze the meat raw materials for few days before sausage manufacture could be a useful practice, especially for the artisan fermented sausages (without starter), because it helps to reduce enterobacteria development and cadaverine production.

STORAGE OF CHEMICALLY PRETREATED WHEAT STRAW – A MEANS TO ENSURE QUALITY RAW MATERIAL FOR PULP PREPARATION

Directory of Open Access Journals (Sweden)

Terttu Heikkilä

2010-07-01

Full Text Available The aim of this study was to evaluate effects of chemical pretreatment and storage on non-wood pulping and on pulp quality. The processes studied were hot water treatment followed by alkaline peroxide bleaching or soda cooking. The results showed that it is possible to store wheat straw outside for at least one year without significant changes in the raw material chemical composition and without adverse effects on the resulting pulp quality. The results are significant to the industry using non-woods to ensure the availability and the quality of the raw-material throughout the year in spite of the short harvesting time.

Raw material from the state of Rio Grande do Norte, Brazil, to obtain sandstone porcelain

International Nuclear Information System (INIS)

Sousa, Maria Rosimar de

2009-01-01

Currently, the production of the ceramic industry of the River Great of the North she is restricted to the manufacture of bricks and roofing tiles. development of new ceramic products of bigger added value, such as gres covering porcelanato, using regional raw materials is of basic importance for the growth of the local ceramic industry and economic development of the region. In this work, they had been studied raw materials as kaolin, sodico feldspato and quartz of the State of the Great River of the North for the attainment of an covering of the gres type porcelanato of base white.The ceramic masses had been prepared by the process saw humid. The body-of-tests they had been conformed by uniaxial prensagem of 40MPa, dried in 110 deg C and burnt between 1160 and 1240 deg, used a cycle of fast burning (approximately 60min.). The qualitative analysis of the formed phases disclosed silica, mullite e sodico feldspato after the sintering. The technological properties of burning evaluated they had been: linear retraction, water absorption, apparent specific mass, porosity and breaking strength to the flexal (shipment of 3 points). Results show that raw materials proceeding from the State of the Great River of North could be used in processes for gres porcelanato, therefore they present characteristics technological, similar chemistry, physics and to the standard of reference and the data of literature. (author)

Mineralogical and technology characterization of raw materials of clay used for ceramic blocks fabrication

International Nuclear Information System (INIS)

Campos, N.Q.; Tapajos, N.S.

2012-01-01

In the state of Para, the red ceramic industry has several segments highly generators of jobs and a strong social appeal. With so many companies focused on this productive sector emerge, but many without any administration quality. Therefore, this study focused the technological and mineralogical characterization of the raw material used in the manufacture of ceramic blocks, by Ceramica Vermelha Company, located in the district of Inhangapi-PA. The raw material was obtained by the techniques of X-ray diffraction (XRD) to determine the present crystalline phases through an accurate and efficient procedure, where it was possible to identify the peaks relating to montmorillonite, illite and kaolinite clay in the sample, and kaolinite and quartz in the sample laterite. Another important result was the absorption of water, with average satisfactory according to the standards. According to a sieve analysis, the laterite the sand fraction showed a greater extent compared to the other, while the clay silt exceeding 80% was found to be too plastic material. The resistance to compression, the results were below the required by the standard, suggesting more accurate test methods. (author)

Selected scientific articles. (Investigations in the field of hydrides chemistry and mineral raw materials processing)

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2013-01-01

Articles, included in the present book are covering period 1977-2013 y. The main scientific articles in the field of power-consuming substances, mineral raw-materials and wastes reprocessing, including uranium industry wastes are collected. Scientific works on hydrogen chemistry which carried out basically bu U.M. Mirsaidov without co-authors are considered. These works are on aluminium hydrides and borohydrides lanthanides. Besides, author's popular-science articles on research carried out by Academy of Sciences during the period when he was the President of Academy of Sciences of the Republic of Tajikistan (1995-2005) are included. Mineral raw materials and wastes reprocessing results are given as well. The book is intended for engineer and technical staff, those working in the field of hydrogen chemistry, hydrometallurgy workers, engineering chemists as well as for PhD, post graduate students and students of appropriate profiles.

Discriminative illumination: per-pixel classification of raw materials based on optimal projections of spectral BRDF.

Science.gov (United States)

Liu, Chao; Gu, Jinwei

2014-01-01

Classifying raw, unpainted materials--metal, plastic, ceramic, fabric, and so on--is an important yet challenging task for computer vision. Previous works measure subsets of surface spectral reflectance as features for classification. However, acquiring the full spectral reflectance is time consuming and error-prone. In this paper, we propose to use coded illumination to directly measure discriminative features for material classification. Optimal illumination patterns--which we call "discriminative illumination"--are learned from training samples, after projecting to which the spectral reflectance of different materials are maximally separated. This projection is automatically realized by the integration of incident light for surface reflection. While a single discriminative illumination is capable of linear, two-class classification, we show that multiple discriminative illuminations can be used for nonlinear and multiclass classification. We also show theoretically that the proposed method has higher signal-to-noise ratio than previous methods due to light multiplexing. Finally, we construct an LED-based multispectral dome and use the discriminative illumination method for classifying a variety of raw materials, including metal (aluminum, alloy, steel, stainless steel, brass, and copper), plastic, ceramic, fabric, and wood. Experimental results demonstrate its effectiveness.

Emergy analysis of biogas systems based on different raw materials.

Science.gov (United States)

Wang, Yang; Lin, Cong; Li, Jing; Duan, Na; Li, Xue; Fu, Yanyan

2013-01-01

Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants' materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system), and the other is the one whose degraded material is corn straw (BPC system). As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials.

Emergy Analysis of Biogas Systems Based on Different Raw Materials

Directory of Open Access Journals (Sweden)

Yang Wang

2013-01-01

Full Text Available Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants’ materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system, and the other is the one whose degraded material is corn straw (BPC system. As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials.

Emergy Analysis of Biogas Systems Based on Different Raw Materials

Science.gov (United States)

Wang, Yang; Lin, Cong; Li, Jing; Duan, Na; Li, Xue; Fu, Yanyan

2013-01-01

Environmental pollution and energy crisis restrict the development of China, and the utilization of renewable technology is an effective strategy to alleviate the damage. Biogas engineering has rapidly developed attributes to solve environmental problems and create a renewable energy product biogas. In this paper, two different biogas plants' materials were analyzed by emergy method. One of them is a biogas project whose degraded material is feces (BPF system), and the other is the one whose degraded material is corn straw (BPC system). As a result, the ecological-economic values of BPF and BPC are $28,300/yr and $8,100/yr, respectively. Considering currency, environment, and human inputs, both of the biogas projects have the ability of disposing waste and potential for development. The proportion of biogas output is much more than fertilizer output; so, fertilizer utilization should be emphasized in the future. In comparison, BPF is better than BPC in the aspects of ecological-economic benefits, environmental benefits, and sustainability. The reason is the difficulty of corn straw seasonal collection and degradation. Thus it is proposed that BPC should be combined with the other raw materials. PMID:23476134

PRINCIPLES OF RE-ENGINEERING METHODOLOGY FOR TECHNOLOGICAL PROCESS IN PROCESSING OF RAW MATERIAL COMPONENTS WHILE PRODUCING CEMENT AND SILICATE PRODUCTS

Directory of Open Access Journals (Sweden)

I. A. Busel

2014-01-01

Full Text Available Grinding process is characterized by high energy consumption and low productivity. Nowadays efficiency of the ball mills applied for grinding is rather low. Only 3-6 % of the supplied power energy is used for material grinding. The rest part of the energy disappears in the form of heat, vibration and noise. So matter concerning reduction of energy consumption is of great importance.Improvement of efficiency and quality of technological process in grinding of raw material components while producing construction materials is considered as one of priority-oriented targets of power- and resource saving in construction industry with the purpose to reduce energy consumption for grinding. Grinding efficiency at operating enterprises is reasonable to improve by modernization of the equipment and existing technological, management and other processes which are related to grinding of mineral raw material. In order to reduce grinding power consumption it is necessary to carry out a complex re-engineering of technological process in grinding of various materials which is based on usage of new modifications of grinding bodies, physical and chemical grinding aids, modern information technologies and industrial automation equipment. Application of modern information technologies and industrial automation equipment makes it possible to execute the grinding process with maximum achievable productivity for existing capacity due to automatic control and consideration of continuous changes in technological parameters. In addition to this such approach gives an opportunity to control processes in real time by immediate adjustments of technological equipment operational modes.The paper considers an approach to the development of re-engineering methodology for technological process in grinding of raw material components while producing construction materials. The present state of technological grinding process is presented in the paper. The paper points out the

Uranium as Raw Material for Nuclear Energy

International Nuclear Information System (INIS)

Lelek, V.

2006-01-01

There is lot of information bringing our attention to the problem of limited raw material resources. Fortunately uranium for nuclear energy is very concentrated source and that is why its transport brings no problems and could be realized from anywhere. Second question is if overall resources are available for current nuclear energy development. Data documenting reasons for nowadays price growth are presenting and it is clearly shown that the most probable explanation is that there is gap in new uranium mines preparation and the lot of smaller mines were closed in the period of low uranium prices. Conclusion is that there is at least for the first half of this century even for thermal reactors enough uranium. Situation could be changed if there will massive production of liquid fuel using hydrogen, produced through nuclear heating. Public information about former military uranium resources are also included. Contemporary about one half of US nuclear power-stations is using high enriched uranium diluted with natural uranium - it is expected to continue this way up to 2012. Uranium is complicated market (Authors)

Dates as raw material for agricultural distilleries

Energy Technology Data Exchange (ETDEWEB)

Laczynski, B

1971-01-01

Pit-containing dates had 88.0 to 89.2% dry matter, 41.7 to 47.5% sucrose, and 2.1 to 2.9% total protein. The mechanical broken charges of raw material were steamed, dispersed to a suspension of 15 to 17/sup 0/ Balling and pH 4.8 to 5.0, enriched with P and N, inoculated with 5 to 7 % of yeast suspension, and acidified to pH > 3.5. Thermophilic yeast cultivated at 27/sup 0/ and fermented below 30/sup 0/ for 2 days gave best results. The fermented liquor had a pH > 3.5, apparent density of 2.0/sup 0/, and contained 7.5 to 9.0 EtOH. From 100 kg dates were obtained 280 t0 340 l of the 15 to 17/sup 0/ dispersion and 320 to 360 l residue containing (per l) 6.0 to 8.5 g protein and 0.04 oat units. EtOH yield (l/quintal) was 914 for potatoes, 28.54 for molasses, 36.29 for cereals, 25.15 for dates, and 18.53 for malt.

Glances on the year 1998. Energies and raw materials

International Nuclear Information System (INIS)

1999-01-01

This report summarizes 14 key-topics of the year 1998 in relation with the French energy and economic policy: the new start-up of energy mastery; the nuclear industry between passion and reason; the labour inspection in nuclear power plants; the law project for the modernizing and development of the electric power public utility; the main gas transportation systems; the future of Gardanne's mining basin; the raw materials in the upheaval; the French refining activity after the Auto-Oil directive; the oil company fusions; the priorities in petroleum technology research; the policy of automotive fuels distribution; the energy in regions; the mining activity in New Caledonia; the end of the BRGM-Normandy partnership. A calendar of remarkable facts is given at the end. (J.S.)

Textile-reinforced concrete using composite binder based on new types of mineral raw materials

Science.gov (United States)

Lesovik, V. S.; Glagolev, E. S.; Popov, D. Y.; Lesovik, G. A.; Ageeva, M. S.

2018-03-01

To determine the level of development of science, it is necessary to start with a particular stage in the development of society. At present, the purpose of building materials science is to create composites, which ensure safety of buildings and structures, including their protection against certain natural and man-made impacts. A new stage in construction materials science envisages the development of a technology for creating composites comfortable for a particular person. To implement this, a new paradigm for designing and synthesizing building materials with a new raw material base is needed. The optimization of the “human-material-habitat” system is a complex task, for the solution of which transdisciplinary approaches are required.

Annual report 2005 General Direction of the Energy and raw materials; Rapport annuel 2005 Direction Generale de L'Energie et des Matieres Premieres

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

This 2005 annual report of the DGEMP (General Direction of the Energy and the raw Materials), takes stock on the energy bill and accounting of the France. The first part presents the electric power, natural gas and raw materials market in France. The second part is devoted to the diversification of the energy resources with a special attention to the renewable energies and the nuclear energy. The third part discusses the energy and raw materials prices and the last part presents the international cooperation in the energy domain. (A.L.B.)

Lithic assemblages of Azokh Cave (Nagorno Karabagh, Lesser Caucasus: Raw materials, technology and regional context

Directory of Open Access Journals (Sweden)

Lena Asryan

2014-03-01

Full Text Available Azokh Cave is a Middle Pleistocene to Holocene site located in Nagorno Karabagh (Lesser Caucasus. The main entrance, Azokh 1, is a large cave that has two geological sequences (lower and upper with nine geo-archaeological units of which only the upper ones (Units I to V have a significant archaeological record.  The faunal remains and lithic artefacts in these units indicate aspects of human occupation, and exploitation of, and association with animals.     The lithic artefacts presented here were recovered from Units V, III and II during the 2002 – 2009 excavation seasons. The available chronological data indicates an age between 293 – 100 Ka for these units. The operational chain is incomplete and artefacts found in the cave are primarily end-products dominated by flake-tools. The assemblage of Unit V is composed primarily of simple, unretouched flakes with a minimal presence of retouched flakes and cores. The Unit II lithic assemblage includes a substantial Levallois component, although with fewer cores and retouched flakes. There are very few flake tools in Unit III. While it is still difficult to assign the Unit V assemblage to a techno-typological group or complex (i.e. Acheulean, Mousterian or other local techno-complexes such as the Kudarian, the Unit II assemblage is clearly associated with Mode 3 or the Mousterian techno-complex.Different local and non-local raw materials were exploited in all units for the production of lithic artefacts, although the range of raw materials is more varied in Unit II. Local chert, flint and basalt were used most commonly, probably due to their easy accessibility. Limestone, jasper and sandstone, from local and non-local sources, are present in small quantities in Units V and II. Obsidian is the only raw material that possibly originates from more distant sources. Flint and chert appear to have been preferentially exploited for flake tool production in all units, but the toolmakers show a

Upper Palaeolithic lithic raw material sourcing in Central and Northern Portugal as an aid to reconstructing hunter-gatherer societies

Directory of Open Access Journals (Sweden)

Thierry Aubry

2016-09-01

Full Text Available We present the results of the study of lithic raw materials used in Upper Palaeolithic occupations preserved in caves, rockshelters and open-air sites from two different geological environments in Portugal. For the sites located in the Lusitanian Basin, flint or silcrete sources are easily available in close vicinity. The Côa Valley sites, located in the Iberian Massif, are within a geological environment where restricted fine-grained vein quartz and siliceous metamorphic rocks are available, but no flint or silcrete, even though both are present in the archaeological assemblages. Data from the two clusters of sites are compared with a third newly located site in the Lower Vouga valley, at the limit of the Iberian Massif with the Lusitanian Basin, where quartz vein raw material types are locally available and flint is about 40 kilometres distant. This study reveals prehistoric adaptations to these different geological contexts, with shorter networks for the Lusitanian basin sites contrasting with the long distance ones for the Côa Valley, and the Vouga site at an intermediary position. Finally, we propose that lithic raw material supply networks, defined by a GIS least-cost algorithm, could be used as a proxy not only for territoriality in the case of local and regional lithic raw material sources, but also to infer long-distance social networks between different Palaeolithic human groups, created and maintained to promote the access to asymmetrically distributed resources.

The European cement industry's approach to the use of secondary raw materials and fuels

Energy Technology Data Exchange (ETDEWEB)

Lawton, J.M.

1992-06-01

Position statements prepared by the European cement industry on the use of secondary raw materials and secondary fuels are introduced and presented. The statements indicate the approach of the industry to the use of these materials and, in the wider context, form part of the industry's overall approach to the environment. (Author). 2 refs.

Study of Pellets and Lumps as Raw Materials in Silicon Production from Quartz and Silicon Carbide

Science.gov (United States)

Dal Martello, E.; Tranell, G.; Gaal, S.; Raaness, O. S.; Tang, K.; Arnberg, L.

2011-10-01

The use of high-purity carbon and quartz raw materials reduces the need for comprehensive refining steps after the silicon has been produced carbothermically in the electric reduction furnace. The current work aims at comparing the reaction mechanisms and kinetics occurring in the inner part of the reduction furnace when pellets or lumpy charge is used, as well as the effect of the raw material mix. Laboratory-scale carbothermic reduction experiments have been carried out in an induction furnace. High-purity silicon carbide and two different high-purity hydrothermal quartzes were charged as raw materials at different molar ratios. The charge was in the form of lumps (size, 2-5 mm) or as powder (size, 10-20 μm), mixed and agglomerated as pellets (size, 1-3 mm) and reacted at 2273 K (2000 °C). The thermal properties of the quartzes were measured also by heating a small piece of quartz in CO atmosphere. The investigated quartzes have different reactivity in reducing atmosphere. The carbothermal reduction experiments show differences in the reacted charge between pellets and lumps as charge material. Solid-gas reactions take place from the inside of the pellets porosity, whereas reactions in lumps occur topochemically. Silicon in pellets is produced mainly in the rim zone. Larger volumes of silicon have been found when using lumpy charge. More SiO is produced when using pellets than for lumpy SiO2 for the same molar ratio and heating conditions. The two SiC polytypes used in the carbothermal reduction experiments as carbon reductants presented different reactivity.

Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

Science.gov (United States)

Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

2017-12-01

Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

Time influence in chemical treatment of Brazilian raw materials type

International Nuclear Information System (INIS)

Argolo, F.; Dias, C.; Machado, A.; Volzone, C.; Ortiga, J.; Valenzuela Diaz, F.

2012-01-01

Clays are part of raw materials in different industries. The mineralogical composition and purity greatly influence the application thereof. Chemical treatments applied, such as acid attack, modify their properties and thus their possible uses. Taking in to account that, clay minerals, may differ by more or less resistance to chemical attacks, two types of clay were studied with different mineralogical composition to assess the degree of resistance to chemical attack treatment such as acid. Acid treatments that were applied, differ mainly in the contact time between the solid and the liquid. The solids were studied by X-ray diffraction analysis, chemical analysis and infrared analysis

Acoustic assessment of wood quality of raw forest materials : a path to increased profitability

Science.gov (United States)

Xiping Wang; Peter Carter; Robert J. Ross; Brian K. Brashaw

2007-01-01

Assessment of the quality of raw wood materials has become a crucial issue in the operational value chain as forestry and the wood processing industry are increasingly under economic pressure to maximize extracted value. A significant effort has been devoted toward developing robust nondestructive evaluation (NDE) technologies capable of predicting the intrinsic wood...

Life cycle assessment of sustainable raw material acquisition for functional magnetite bionanoparticle production.

Science.gov (United States)

Sadhukhan, Jhuma; Joshi, Nimisha; Shemfe, Mobolaji; Lloyd, Jonathan R

2017-09-01

Magnetite nanoparticles (MNPs) have several applications, including use in medical diagnostics, renewable energy production and waste remediation. However, the processes for MNP production from analytical-grade materials are resource intensive and can be environmentally damaging. This work for the first time examines the life cycle assessment (LCA) of four MNP production cases: (i) industrial MNP production system; (ii) a state-of-the-art MNP biosynthesis system; (iii) an optimal MNP biosynthesis system and (iv) an MNP biosynthesis system using raw materials sourced from wastewaters, in order to recommend a sustainable raw material acquisition pathway for MNP synthesis. The industrial production system was used as a benchmark to compare the LCA performances of the bio-based systems (cases ii-iv). A combination of appropriate life cycle impact assessment methods was employed to analyse environmental costs and benefits of the systems comprehensively. The LCA results revealed that the state-of-the-art MNP biosynthesis system, which utilises analytical grade ferric chloride and sodium hydroxide as raw materials, generated environmental costs rather than benefits compared to the industrial MNP production system. Nevertheless, decreases in environmental impacts by six-fold were achieved by reducing sodium hydroxide input from 11.28 to 1.55 in a mass ratio to MNPs and replacing ferric chloride with ferric sulphate (3.02 and 2.59, respectively, in a mass ratio to MNPs) in the optimal biosynthesis system. Thus, the potential adverse environmental impacts of MNP production via the biosynthesis system can be reduced by minimising sodium hydroxide and substituting ferric sulphate for ferric chloride. Moreover, considerable environmental benefits were exhibited in case (iv), where Fe(III) ions were sourced from metal-containing wastewaters and reduced to MNPs by electrons harvested from organic substrates. It was revealed that 14.4 kJ and 3.9 kJ of primary fossil resource

Non-thermal plasma treatment as a new biotechnology in relation to seeds, dry fruits, and grains

Science.gov (United States)

Božena, ŠERÁ; Michal, ŠERÝ

2018-04-01

Non-thermal plasma (NTP) technology offers wide potential use in the food technology, the same as in the unconventional agriculture. Some seeds, dry fruits, grains and their sprouts gain popularity in the culinary industry as ‘raw seeds’. This review paper draws the current research and trends in NTP pre-treatment of selected seeds/fruits that are useable as ‘raw seeds’. The main applications are connected with activation of seed germination, early growth of seedlings, microbial inactivation of seed/fruit surface, and possibility of increasing quantity of biological active compounds in sprouting seeds. The paper presents a list of plant species that are able to be used as ‘raw seed’ including current information about main type of NTP treatment implemented.

The Structural Characterisation of Risk in the R&D Process of Functional Raw Materials for Electronic Devices

OpenAIRE

Chikamori, Yoji; Nasu, Seigo

2017-01-01

The electronic materials and electronics device industries remain important to Japan in spite of the general decline of the Japanese electronics industry. There is risk and uncertainty when developing functional materials in the electronics industry. However, studies examining the uncertainty and risk variables in the development of functional materials are scarce. This study examines incremental research and development (R&D) developed for raw functional materials for electronics. Our analys...

Use of high-boiling point organic solvents for pulping oil palm empty fruit bunches.

Science.gov (United States)

Rodríguez, Alejandro; Serrano, Luis; Moral, Ana; Pérez, Antonio; Jiménez, Luis

2008-04-01

Oil palm empty fruit bunches were used as an alternative raw material to obtain cellulosic pulp. Pulping was done by using high-boiling point organic solvents of decreased polluting power relative to classical (Kraft, sulphite) solvents but affording operation at similar pressure levels. The holocellulose, alpha-cellulose and lignin contents of oil palm empty fruit bunches (viz. 66.97%, 47.91% and 24.45%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using ethyleneglycol, diethyleneglycol, ethanolamine and diethanolamine under two different sets of operating conditions, namely: (a) a 70% solvent concentration, 170 degrees C and 90 min; and (b) 80% solvent, 180 degrees C and 150 min. The solid/liquid ratio was six in both cases. The amine solvents were found to provide pulp with better properties than did the glycol solvents. Ethanolamine pulp exhibited the best viscosity and drainage index (viz. 636 mL/g and 17 degrees SR, respectively), and paper made from it the best breaking length (1709 m), stretch (1.95%), burst index (0.98 kN/g) and tear index (0.33 mNm(2)/g). Operating costs can be reduced by using milder conditions, which provide similar results. In any case, the amines are to be preferred to the glycols as solvents for this purpose.

Regenerative raw materials. High technology without end; Nachwachsende Rohstoffe. Spitzentechnologie ohne Ende

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-11-03

In recent years, the use of renewable raw materials has developed rapidly. Meanwhile, biomass is one of the most important renewable energy source and a serious alternative to fossil fuel-based industry. The brochure under consideration presents an insight into the complex and promising topic ''Renewable Resources''. In particular, the areas in which renewable resources already are established as well as areas that need to be extended in the future are described.

Macrophage activating activity of pyrrole alkaloids from Morus alba fruits.

Science.gov (United States)

Kim, Seon Beom; Chang, Bo Yoon; Jo, Yang Hee; Lee, Sang Hoon; Han, Sang-Bae; Hwang, Bang Yeon; Kim, Sung Yeon; Lee, Mi Kyeong

2013-01-09

The fruits of Morus alba have been traditionally used as a tonic to enhance immune responses. The macrophage activating constituents of Morus alba fruits were purified using various column chromatography techniques. The structures of isolated compounds were determined on the basis of spectroscopic data interpretation such as 1D and 2D NMR analysis. The macrophage activating activities of isolated compounds were evaluated by measuring the production of nitric oxide, TNF-α and IL-12 in RAW 264.7 cells. The phagocytic activity was also evaluated. Five pyrrole alkaloids, 5-(hydroxymethyl)-1H-pyrrole-2-carboxaldehyde (1), 2-formyl-1H-pyrrole-1-butanoic acid (2), 2-formyl-5-(hydroxymethyl)-1H-pyrrole-1-butanoic acid (3), 2-formyl-5-(methoxymethyl)-1H-pyrrole-1-butanoic acid (4) and Morrole A (5) were isolated from the fruits of Morus alba. Morrole A (5) is first reported in nature and other pyrrole alkaloids (1-4) are first reported from Morus species. Among the isolated compounds, compounds 3 and 4 significantly activated macrophage activity by the enhancement of nitric oxide, TNF-α and IL-12 production, and the stimulation of phagocytic activity in RAW 264.7 cells. Pyrrole alkaloids, including a new compound, were isolated from Morus alba fruits. These compounds activated macrophage activity in RAW 264.7 cells. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Potential of Electronic Plastic Waste as a Source of Raw Material and Energy Recovery

International Nuclear Information System (INIS)

Norazli Othman; Nor Ezlin Ahmad Basri; Lariyah Mohd Sidek

2009-01-01

Nowadays, the production of electronic equipment is one of the fastest growing industrial activities in this world. The increase use of plastic in this sector resulted in an increase of electronic plastic waste. Basically, electronic plastic material contains various chemical elements which act as a flame retardant when electronic equipment is operated. In general, the concept of recycling electronic plastic waste should be considered in order to protect the environment. For this purpose, research has been conducted to different resins of electronic plastic waste to identify the potential of electronic plastic waste as a source of raw material and energy recovery. This study was divided into two part for example determination of physical and chemical characteristics of plastic resins and calculation of heating value for plastic resins based on Dulong formula. Results of this research show that the average calorific value of electronic waste is 30,872.42 kJ/ kg (7,375 kcal/ kg). The emission factor analysis showed that the concentration of emission value that might occur during waste management activities is below the standard set by the Environment Quality Act 1974. Basically, this research shows that electronic plastic waste has the potential to become the source of raw material and energy recovery. (author)

Determination of Au, Pt, Pd in gold ore mineral raw materials by stripping voltammetry

Directory of Open Access Journals (Sweden)

Kolpakova N.A.

2016-01-01

Full Text Available The paper considers the possibilities of use of the method of stripping voltammetry for finding platinum metals in mineral gold and ore raw material. A review of new options of electro-concentration of platinum metals on the surface of graphite electrode with the following sediment electro-oxidation and receipt of an analytical signal is presented: platinum finding was carried out by picks of selective electro-oxidation of iridium from intermetallic compound with platinum; gold finding was carried out by picks of gold electro-oxidation on the surface of graphite electrode modified by bismuth; palladium finding was performed by picks of palladium electro-oxidation on the surface of graphite electrode. 1M HCL solution was selected as a supporting electrolyte. Gold and hydrogen elimination on the process of palladium electro-oxidation was performed by means of UV irradiation of solution in the process of electro-concentration of palladium sediment. Gold, platinum and palladium determination was carried out in mineral gold and ore raw material of Verkhneamylskiy gold and ore district.

Beyond waste: new sustainable fillers from fly ashes stabilization, obtained by low cost raw materials

Directory of Open Access Journals (Sweden)

N. Rodella

2016-09-01

Full Text Available A sustainable economy can be achieved only by assessing processes finalized to optimize the use of resources. Waste can be a relevant source of energy thanks to energy-from-waste processes. Concerns regarding the toxic fly ashes can be solved by transforming them into resource as recycled materials. The commitment to recycle is driven by the need to conserve natural resources, reduce imports of raw materials, save landfill space and reduce pollution. A new method to stabilize fly ash from Municipal Solid Waste Incinerator (MSWI at room temperature has been developed thanks to COSMOS-RICE LIFE+ project (www.cosmos-rice.csmt.eu. This process is based on a chemical reaction that occurs properly mixing three waste fly ashes with rice husk ash, an agricultural by-product. COSMOS inert can replace critical raw materials (i.e. silica, fluorspar, clays, bentonite, antimony and alumina as filler. Moreover the materials employed in the stabilization procedure may be not available in all areas. This paper investigates the possibility of substituting silica fume with corresponding condensed silica fume and to substitute flue-gas desulfurization (FGD residues with low-cost calcium hydroxide powder. The removal of coal fly ash was also considered. The results will be presented and a possible substitution of the materials to stabilize fly ash will be discussed.

Determination of polysaccharide yield from the fruiting bodies and mycelium of selected mushroom species

International Nuclear Information System (INIS)

Shaiful Azuar Mohamad; Mat Rasol Awang

2006-01-01

Numerous polysaccharides and polysaccharides-protein complexes have been isolated from mushrooms and used as a source of therapeutic agents. The mycelium of Pleurotus sajor caju, Pleurotus tuber-regium, black ganoderma, and the fruiting bodies of Pleurotus sajor caju and Pleurotus florida were used to determine the percentage of polysaccharides obtained from the mushroom raw material. Hot water extraction method was used followed by refrigerated centrifuge and lyophilization. The yield from the various species will be compared. (Author)

Analytical methods to characterize heterogeneous raw material for thermal spray process: cored wire Inconel 625

Science.gov (United States)

Lindner, T.; Bonebeau, S.; Drehmann, R.; Grund, T.; Pawlowski, L.; Lampke, T.

2016-03-01

In wire arc spraying, the raw material needs to exhibit sufficient formability and ductility in order to be processed. By using an electrically conductive, metallic sheath, it is also possible to handle non-conductive and/or brittle materials such as ceramics. In comparison to massive wire, a cored wire has a heterogeneous material distribution. Due to this fact and the complex thermodynamic processes during wire arc spraying, it is very difficult to predict the resulting chemical composition in the coating with sufficient accuracy. An Inconel 625 cored wire was used to investigate this issue. In a comparative study, the analytical results of the raw material were compared to arc sprayed coatings and droplets, which were remelted in an arc furnace under argon atmosphere. Energy-dispersive X-ray spectroscopy (EDX) and X-ray fluorescence (XRF) analysis were used to determine the chemical composition. The phase determination was performed by X-ray diffraction (XRD). The results were related to the manufacturer specifications and evaluated in respect to differences in the chemical composition. The comparison between the feedstock powder, the remelted droplets and the thermally sprayed coatings allows to evaluate the influence of the processing methods on the resulting chemical and phase composition.

National reports on raw materials economy. Vol. 6

International Nuclear Information System (INIS)

Haude, H.; Weber, R.

1975-06-01

A review is given of the ore deposits, mine production, and use of mineral resources in Argentina (oil, gas, asphalt, oil shale, coal, uranium, thorium, iron, manganese, chrome, tungsten, vanadium, copper, lead, zinc, tin, antimony, gold, silver, aluminium, beryllium, boron, sulfur, and fluorite). Argentina is dependent on imports of nearly all mineral resources. Only exports of zinc, tungsten, fluorite, and borate have been possible and the only other significant production has been of energy resources, iron, manganese, and lead. The extreme concentration of population in the east, the great distances to the Andes in the west, and the as yet inadequate transport network with the west has limited the mining activity up to the present. As part of industrial development, the government has made great efforts to increase the supply of raw materials through intensive prospecting and use of Argentina's own natural resources. Newly discovered ore deposits confirm that extensive parts of the country are prospective for mineral resources. (orig.) [de

Radiation situation during underground mineral raw materials mining

International Nuclear Information System (INIS)

Ogorodnikov, B.I.

2007-01-01

One studied the content and the ratio of 4 0 K, 226 Ra, 232 Th and 238 U natural radionuclides in the ores mined in Egypt, Iran, China and Turkey. It is shown that in some ores, for example, in the carbonaceous shale mined in China, in the Iranian bauxite and turquoise Ra eq is higher than 370 Bq/kg, that is, it is higher than the value recommended by the International Scientific Committee on Radiation Effect. The Chinese bituminous shale shows high content of 226 Ra, while 226 Ra/ 232 Th concentration ratio varies between 10 and 60 in contrast to that of other numerous mineral raw materials being close to 1-3. In a number of mines one recorded high concentrations of radon (higher than 300 Bq/m 3 ). Inhalation of such an air results in the essential internal irradiation. The average annual dose equivalents for miners may be higher than the maximum permissible value equal to 20 mSv/g [ru

The key numbers of the mineral raw materials

International Nuclear Information System (INIS)

Mandil, C.

1996-01-01

Mineral raw materials come from fossil reserves or ores resulting from the geologic and climatic history of the Earth. The access to economic development for 80% of the worldwide population and the high rate of demographic growth (probably 8 billions of inhabitants in 2025) are important factors that can greatly multiply the worldwide consumption of ores. In parallel, environmental concerns and the increasing need for a better equilibrium between wildlife preservation and the supply of economic needs, lead to a more reasonable and mastered use of natural resources. The aim of this book is to shade light and give global elements of thoughts on mineral resources, and for the main of those (about 30 metals and mineral substances), to review the most useful data and references about their production and consumption. For each question, chapters are devoted to the situation of France in its worldwide context. One chapter concerns the uranium ores (reserves, production, prices evolution, consumption, economic flux and companies involved). (J.S.)

Multicriteria analysis of agricultural raw materials: A case study of BSBIOS and PETROBRAS BIOFUELS in Brazil

International Nuclear Information System (INIS)

Zonin, Valdecir José; Valle Antunes, José Antônio; Pinto Leis, Rodrigo

2014-01-01

Energy crises reverberate within societies and encourage worldwide change in this industry. In this context, Brazil has been consolidating the National Program for the Production and Use of Biodiesel (Programa Nacional de Produção e Uso do Biodiesel—PNPB). This article analyzes BSBIOS and PETROBRAS BIOFUELS, which is a company that is incorporated under the PNPB. After providing an overview, the manuscript focuses on the criteria used for the selection of the agricultural raw materials used in the biodiesel industry. A reference model that considered the economic, technological, and social dimensions was developed; these dimensions were analyzed in relation to the production matrices of the soybean, canola, sunflower, and castor plants. The company strategically opted to establish programs for promoting the production of only soybean and canola. In the short term, the company has accepted the evidence that the main source of raw materials is soybean production. This decision was made considering the multicriteria analysis that was developed, which involved a number of economic, technological, and social aspects. Consequently, this analysis used in the decision-making process exhibits both a macro (the national and international environment) and a micro perspective (the companies’ reality). - Highlights: • The economic viability of biodiesel production in Brazil hinges on crop production. • Biodiesel production in Brazil requires developing an efficient production chain. • Oleaginous crops will be diversified by creating a network of suppliers. • Raw material production is diversifying based on an analysis of relevant factors

The Potential of Tree Fruit Stone and Seed Wastes in Greece as Sources of Bioactive Ingredients

Directory of Open Access Journals (Sweden)

Stella A. Ordoudi

2018-03-01

Full Text Available The inedible part (stones, husks, kernels, seeds of the tree fruits that are currently processed in various regions of Greece constitutes a huge portion of the fruit processing solid waste that remains underexploited. In this review, the existing scientific background for the composition and content of fruit stone and seed in bioactive ingredients is highlighted for olives, stone fruits and citrus fruits that represent the economically most important tree crop products of the country. The content of bioactive compounds may vary considerably depending on the quality of the raw material and the treatment during processing. However, both the hydrophilic and the lipophilic fractions of the seeds contain significant amounts of the primary and the secondary plant metabolites. Among them, phytosterols and several types of polyphenols, but also squalene, tocopherols and some other terpenoids with a unique structure are of particular importance for the utilization and valorization of stones and seeds. Official and scholar records about the current management practices are also presented to highlight the dynamics of the Greek fruit sector. Prospects for the regionalization of fruit seed wastes, in line with EU-promoted Research and Innovation Strategies (RIS for Smart Specialization are critically discussed.

Towards a dynamic assessment of raw materials criticality: Linking agent-based demand — With material flow supply modelling approaches

International Nuclear Information System (INIS)

Knoeri, Christof; Wäger, Patrick A.; Stamp, Anna; Althaus, Hans-Joerg; Weil, Marcel

2013-01-01

Emerging technologies such as information and communication-, photovoltaic- or battery technologies are expected to increase significantly the demand for scarce metals in the near future. The recently developed methods to evaluate the criticality of mineral raw materials typically provide a ‘snapshot’ of the criticality of a certain material at one point in time by using static indicators both for supply risk and for the impacts of supply restrictions. While allowing for insights into the mechanisms behind the criticality of raw materials, these methods cannot account for dynamic changes in products and/or activities over time. In this paper we propose a conceptual framework intended to overcome these limitations by including the dynamic interactions between different possible demand and supply configurations. The framework integrates an agent-based behaviour model, where demand emerges from individual agent decisions and interaction, into a dynamic material flow model, representing the materials' stocks and flows. Within the framework, the environmental implications of substitution decisions are evaluated by applying life-cycle assessment methodology. The approach makes a first step towards a dynamic criticality assessment and will enhance the understanding of industrial substitution decisions and environmental implications related to critical metals. We discuss the potential and limitation of such an approach in contrast to state-of-the-art methods and how it might lead to criticality assessments tailored to the specific circumstances of single industrial sectors or individual companies. - Highlights: ► Current criticality assessment methods provide a ‘snapshot’ at one point in time. ► They do not account for dynamic interactions between demand and supply. ► We propose a conceptual framework to overcomes these limitations. ► The framework integrates an agent-based behaviour model with a dynamic material flow model. ► The approach proposed makes

Effect of drying parameters on physiochemical and sensory properties of fruit powders processed by PGSS-, Vacuum- and Spray-drying.

Science.gov (United States)

Feguš, Urban; Žigon, Uroš; Petermann, Marcus; Knez, Željko

2015-01-01

Aim of this experimental work was to investigate the possibility of producing fruit powders without employing drying aid and to investigate the effect of drying temperatures on the final powder characteristics. Raw fruit materials (banana puree, strawberry puree and blueberry concentrate) were processed using three different drying techniques each operating at a different temperature conditions: vacuum-drying (-27-17 °C), Spray-drying (130-160 °C) and PGSS-drying (112-152 °C). Moisture content, total colour difference, antioxidant activity and sensory characteristics of the processed fruit powders were analysed. The results obtained from the experimental work indicate that investigated fruit powders without or with minimal addition of maltodextrin can be produced. Additionally, it was observed that an increase in process temperature results in a higher loss of colour, antioxidant activity and intensity of the flavour profile.

Potential recovery of industrial wood and energy wood raw material in different cutting and climate scenarios for Finland

International Nuclear Information System (INIS)

Kaerkkaeinen, Leena; Nuutinen, Tuula; Matala, Juho; Kellomaeki, Seppo; Haerkoenen, Kari

2008-01-01

The aim of this study was to estimate the simultaneous recovery of industrial wood and raw material for energy wood from cuttings in Finland during the next 50 years. Two cutting scenarios (maximum and sustainable cuttings) and two climate scenarios (current and changing climate) were analysed to determine their impacts on harvesting potential. The analysis was carried out using sample plot and tree data from the ninth National Forest Inventory and a management-oriented large-scale forestry model (MELA) into which the transfer functions based on physiological modelling were incorporated to describe the impacts of climate change. Depending on the climate scenario, the volume of potential recovery of industrial wood in the maximum cutting scenario during the period 2003-2013 varied from 103 to 105 million m 3 a -1 , while the amount of potential energy wood raw material was 35 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 64 million m 3 a -1 and energy wood raw material 22 Tg a -1 , and in the changing climate scenario, 85 million m 3 a -1 and 29 Tg a -1 , respectively. In the sustainable cutting scenario, depending on the climate scenario used, the potential recovery of industrial wood during the period 2003-2013 varied from 74 to 76 million m 3 a -1 , while the amount of potential energy wood was 25 Tg a -1 . During the period 2043-2053, in the current climate scenario, the potential recovery of industrial wood was 80 million m 3 a -1 and energy wood raw material 26 Tg a -1 , and in the changing climate scenario, 88 million m 3 a -1 and 29 Tg a -1 , respectively. (author)

Isolation and identification of lactic acid bacteria from fermented red dragon fruit juices.

Science.gov (United States)

Ong, Yien Yien; Tan, Wen Siang; Rosfarizan, Mohamad; Chan, Eng Seng; Tey, Beng Ti

2012-10-01

Red dragon fruit or red pitaya is rich in potassium, fiber, and antioxidants. Its nutritional properties and unique flesh color have made it an attractive raw material of various types of food products and beverages including fermented beverages or enzyme drinks. In this study, phenotypic and genotypic methods were used to confirm the identity of lactic acid bacteria (LAB) appeared in fermented red dragon fruit (Hylocereus polyrhizus) beverages. A total of 21 isolates of LAB were isolated and characterized. They belonged to the genus of Enterococcus based on their biochemical characteristics. The isolates can be clustered into two groups by using the randomly amplified polymorphic DNA method. Nucleotide sequencing and restriction fragment length polymorphism of the 16S rRNA region suggested that they were either Enterococcus faecalis or Enterococcus durans. Current research revealed the use of biochemical analyses and molecular approaches to identify the microbial population particularly lactic acid bacteria from fermented red dragon fruit juices. © 2012 Institute of Food Technologists®

Laser desorption/ionization mass spectrometry for direct profiling and imaging of small molecules from raw biological materials

Energy Technology Data Exchange (ETDEWEB)

Cha, Sangwon [Iowa State Univ., Ames, IA (United States)

2008-01-01

Matrix-assisted laser desorption/ionization(MALDI) mass spectrometry(MS) has been widely used for analysis of biological molecules, especially macromolecules such as proteins. However, MALDI MS has a problem in small molecule (less than 1 kDa) analysis because of the signal saturation by organic matrixes in the low mass region. In imaging MS (IMS), inhomogeneous surface formation due to the co-crystallization process by organic MALDI matrixes limits the spatial resolution of the mass spectral image. Therefore, to make laser desorption/ionization (LDI) MS more suitable for mass spectral profiling and imaging of small molecules directly from raw biological tissues, LDI MS protocols with various alternative assisting materials were developed and applied to many biological systems of interest. Colloidal graphite was used as a matrix for IMS of small molecules for the first time and methodologies for analyses of small metabolites in rat brain tissues, fruits, and plant tissues were developed. With rat brain tissues, the signal enhancement for cerebroside species by colloidal graphite was observed and images of cerebrosides were successfully generated by IMS. In addition, separation of isobaric lipid ions was performed by imaging tandem MS. Directly from Arabidopsis flowers, flavonoids were successfully profiled and heterogeneous distribution of flavonoids in petals was observed for the first time by graphite-assisted LDI(GALDI) IMS.

Analysis of zirconia and alumina products and raw materials by X-ray fluorescence spectrometry

International Nuclear Information System (INIS)

Boix, A.; Draignaud, M.; Debras-Guedon, J.

1975-01-01

An X-ray fluorescence spectrometric method of analysis for various raw materials and materials based on zirconia, alumina and silica was developed. The measurements were made on beads made from the sample and a borax based flux, in the proportions 1:10. A repeatability test allowed the relative standard deviation to be estimated for the three main constituents: SiO 2 , Al 2 O 3 , ZrO 2 : it is at the level of 1%. The element analyzed are: Si, Al, Fe, Ti, Ca, Hf and Zr [fr

CANDIED WATERMELON. INDUSTRIAL RAW MATERIALS (SPECIFICATIONS

Directory of Open Access Journals (Sweden)

L. V. Pavlov

2016-01-01

Full Text Available The purpose of the standard is the valuation of the indicators of quality of candied fruit watermelon, cooked in sugar syrup, dried and coated in granulated sugar intended for industrial processing and nutrition. This standard is developed for the first time in the Russian Federation.

Study of nanocomposites based polyurethanes obtained of the biodiesel from passion fruit with fiber cashew

International Nuclear Information System (INIS)

Araujo, B.R.S.; Breves, R.A.; Santos, M.A.; Lopes, R.V.V.; Macedo, J.L.; Ceschin, A.M.; Sales, M.J.A.

2014-01-01

In this work, polyurethanes (PUs) prepared with polyol obtained of the biodiesel from passion fruit oil (BIPFO) and composites with cashew fiber 'in natura' were developed. The synthesis of polyol (PBIPFO) consisted in the epoxidation/hydroxylation of BIOM in one step, using performic acid generated 'in situ'. The instaurations the passion fruit oil (PFO) and the reactions of obtaining the BIOM and PBIOM were confirmed by nuclear magnetic resonance (NMR) "1H and infrared spectroscopy (FTIR). The PUs were prepared using PBIPFO with 4,4-diphenylmethane diisocyanate (MDI) at molar ratio [NCO]/[OH] of 1.5. PUs and composites were analyzed by FTIR, thermogravimetry (TG), derivative thermogravimetry (DTG) and dynamic mechanical analysis (DMA). The use of BIPFO as raw material to get PUs and composites with cashew fiber showed viability by success of the reactions throughout the process and properties of the materials obtained. (author)

Effects of dehydration methods on quality characteristics of yellow passion fruit co-products.

Science.gov (United States)

Silva, Neiton C; Duarte, Claudio R; Barrozo, Marcos As

2017-11-01

The production and processing of fruits generate a large amount of residues, which are usually disposed of or under-used, representing losses of raw material and energy. The present paper investigates the effect of four dehydration techniques (convective, infrared, microwave and freeze-drying) on yellow passion fruit (Passiflora edulis f. flavicarpa) co-products and the influence of the main variables on moisture removal and bioactive compounds. The compounds analyzed were total phenolics, total flavonoids, ascorbic acid and pectin. The content of phenolics and flavonoids increased after dehydration in all techniques investigated and the process temperatures directly affected the ascorbic acid content. Microwave dehydration showed the best results for most bioactive compounds analyzed, if performed in suitable process conditions. However, the highest levels of pectin content were obtained by freeze-drying and convective dehydration. This study reinforces the importance of the adequate use of passion fruit co-products due to the high levels of bioactive compounds in this material. Microwave dehydration presented the best results, which indicates the potential use of this technique for a better exploitation of fruit co-products. Larger quantities of pectin were extracted from samples dehydrated through methodologies with long-time process and low temperatures, such as convective drying and freeze-drying. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Primary Copper Smelter and Refinery as a Recycling Plant—A System Integrated Approach to Estimate Secondary Raw Material Tolerance

Directory of Open Access Journals (Sweden)

Olof Forsén

2017-10-01

Full Text Available The primary production of sulfide concentrates includes smelting to copper matte or blister copper, conversion of matte to blister copper, and refining to copper. Smelting, converting, and fire-refining can use a limited amount of secondary materials. Molten copper can effectively dissolve many metals, from valuable noble metals to harmful impurities such as bismuth. However, some of the impurity metals in copper are valuable in other applications. In this paper, we outline the main material flows in copper smelting and electrorefining and describe how minor metals can be recovered from secondary raw materials using copper as a carrier material. We will use a system integrated approach to define the factors that affect the recovery of different metals and copper quality. Metals typical in copper production are used as examples, like noble metals, As, Bi, Se, and Te, including metals in the EU critical raw materials list like PGM and Sb.

Rare earth elements exploitation, geopolitical implications and raw materials trading

Science.gov (United States)

Chemin, Marie-Charlotte

2015-04-01

, establishing a company in China can lower the production cost (since the company buys the products used in its production at a lower price). In the fifth session, they study the raw materials trading based on the futures contracts example. A producer, to avoid a rise in prices of raw materials used in his production can use derivative products on the financial market: futures contracts for instance. This product ensures a quantity and quality for a price and a delivery date agreed upon today. Actually, producers can use a method called Fix price hedging in order to fix the price of a specific product. The main idea is to balance out the "physical position" (spot market) and the "paper position" (futures market). Even if the REE are commercialized in form of a non-perishable's oxide, the flow of the stock must be guaranteed and this is why it is important for producers to secure their supply of raw materials. In the last session, students search local companies that use REE in their production process and study their strategy on the market.

TA-study for use of regenerative raw materials within technologies to be developed in the future and used by the Middle-German chemical industry and the necessary research projects

International Nuclear Information System (INIS)

Fuertig, H.; Fleischer, L.G.; Doetsch, P.

1991-12-01

This TA-study deals with the evaluation of innovative, marketable, and ecologically sound research strategies, technologies and products regarding the use of regenerative raw materials for the chemical industry. Intensified use of regenerative raw materials facilitates a material economy, that is closely interlinked with natural cycles and thus ecologically advantegous (aspect of whole plant utilization); economical aspects like self-sufficiency concerning regenerative material, the expected shortage of fossile raw materials and energy ressources that will be followed by an increase in price, the possible skimming off agricultural overcapacities, and a relative reduction of cost of agrarian raw material as well as the utilization of waste products and residues from agriculture and forestry support the use in technical processes. (orig.) [de

Determination of Bacterial Pathogen in Foods for Export and their Raw Material

International Nuclear Information System (INIS)

Marambio, E.; Cordano, A.M.; Insunza, M.; Fernández, M.; Astorga, J.

2005-01-01

Chile is a South American country with an important fish and shellfish production. These products are some of the most important items for the economy of the country. From 1998 to 2001, Chile exported $1 137 625 788 of fish and shellfish. Statistics also show that frozen vegetables are fast becoming high on the food export list. During recent years (1998 to 2001) $223 312 248 worth of frozen vegetables were exported to different countries. This study was performed to trace the presence of pathogens in some of these Chilean foods to be exported: 97 samples of salmon and 84 samples of different frozen vegetables (asparagus, peas and corn) were analyzed in order to determine their levels of microbial contamination. Total bacteria counts (mesophilic aerobes bacteria), Escherichia coli, Staphylococcus aureus, Bacillus cereus, Clostridium perfringens, Salmonella spp. and Listeria monocytogenes were tested. Vibrio cholerae was tested only in salmon samples. The analysis of salmon samples showed that the raw material presented a very good quality. However, during the filleting process the fish was contaminated, presenting higher total bacteria counts. Only one of the 48 final product samples presented contamination with a pathogenic bacteria (Listeria monocytogenes (<100 cfu/g)). Frozen vegetable samples (raw material and final products) did not present any of the pathogen bacteria studied. The mesophilic aerobes bacteria counts were reduced during processing due to the effectiveness of the good manufacturing practices and the technological process used. (author)

Determination of Bacterial Pathogen in Foods for Export and their Raw Material

Energy Technology Data Exchange (ETDEWEB)

Marambio, E.; Cordano, A. M.; Insunza, M.; Fernández, M.; Astorga, J. [Sección Microbiología de Alimentos, Instituto de Salud Pública de Chile (Chile)

2005-01-15

Chile is a South American country with an important fish and shellfish production. These products are some of the most important items for the economy of the country. From 1998 to 2001, Chile exported $1 137 625 788 of fish and shellfish. Statistics also show that frozen vegetables are fast becoming high on the food export list. During recent years (1998 to 2001) $223 312 248 worth of frozen vegetables were exported to different countries. This study was performed to trace the presence of pathogens in some of these Chilean foods to be exported: 97 samples of salmon and 84 samples of different frozen vegetables (asparagus, peas and corn) were analyzed in order to determine their levels of microbial contamination. Total bacteria counts (mesophilic aerobes bacteria), Escherichia coli, Staphylococcus aureus, Bacillus cereus, Clostridium perfringens, Salmonella spp. and Listeria monocytogenes were tested. Vibrio cholerae was tested only in salmon samples. The analysis of salmon samples showed that the raw material presented a very good quality. However, during the filleting process the fish was contaminated, presenting higher total bacteria counts. Only one of the 48 final product samples presented contamination with a pathogenic bacteria (Listeria monocytogenes (<100 cfu/g)). Frozen vegetable samples (raw material and final products) did not present any of the pathogen bacteria studied. The mesophilic aerobes bacteria counts were reduced during processing due to the effectiveness of the good manufacturing practices and the technological process used. (author)

Iron zircon pigment synthesis: Proposal of a mixing index for the raw materials mixtures

International Nuclear Information System (INIS)

Zumaquero, E.; Ortsb, M.J.; Sanz, V.; Mestre, S.

2017-01-01

Iron zircon coral pigments are very interesting from an industrial point of view because of their high colouring power and their stability at high temperatures. However, the pigment's synthesis is particularly troublesome due to its specific reaction mechanism. As an encapsulated pigment it becomes very important how the raw materials are distributed in the reaction mixture. To evaluate the effectiveness of the mixing process, it would be convenient to define a parameter, that is the mixing index, to estimate the degree of homogeneity of the system. In the current investigation, a mixing index is proposed derived from the power spectrum of Fourier transform of scanning electron microscope (SEM) images of the raw material mixture. Concretely, the number of pixels in a certain range of values in the image of the power spectrum, seems to behave relatively well as mixing index. This index allows us to distinguish between samples with different zirconia and iron oxide used as precursors. The proposed mixing index seems to be related to the colouring power of the final pigment when the synthesis generates enough zircon to encapsulate hematite particles. [es

Consumer preferences in respect of processed fruit and berry products

Directory of Open Access Journals (Sweden)

Gribova N. А.

2017-09-01

Full Text Available Nowadays fruits, berries and processed products are an indispensable component of the human diet throughout the year. Frozen fruits and berries are widely distributed on the Russian market and are part of the food industry worldwide. Frozen products become popular among consumers for home use due to the minimal cooking time. Consumer evaluation is the most relevant and significant for identifying preferences and evaluating quality products in Russian markets. In this regard, a qualitative analysis of marketing research has been carried out and preferences have been identified according to which criteria consumers buy quick-frozen products. Some methods of sensory analysis have been used (consumer evaluation, the profile method, and pairwise comparison method. The dominant factor in choosing a brand of quick-frozen products is the combination of an acceptable price and quality, and to a lesser extent, the recommendation of acquaintances, the type of packaging and advertising of products. The research is aimed at identifying organoleptic properties that affect the consumer evaluation of the quality of frozen, thawed grapes in comparison with the reference product. Fruits and berries freeze for hours and even minutes, but are stored for a long time. The problem arises in rehydration – the return of the product to its original state, close to fresh natural raw material. The main goal of the research is aimed at identifying some rational method of defrosting, corresponding to organoleptic and consumer properties. With the help of organoleptic evaluation the best ways of defrosting have been identified – the microwave oven and the freezer. These methods allow obtaining thawed foods with the finest quality and identical to natural raw materials. The storage time after defrosting has been revealed: in the microwave oven – 60 min; at the room temperature – 80 min; in the coldstore – 100 min. The obtained information can be useful for consumers

High belite cement from alternative raw materials

Directory of Open Access Journals (Sweden)

Ghorab, H. Y.

2014-05-01

Full Text Available Three high belite laboratory clinkers were prepared from traditional and alternative raw materials. Reference clinker was obtained from 77% limestone, 11% sandy clays, 11% fatty clays and 1% iron scales. The fatty clays were replaced by red brick powder in the raw meal of the second clinker and were lowered to 2% with the replacement of 10% of the limestone by egg shells in the third clinker. The SEM examination revealed clear presence of crossed striae and twinning in the rounded belite grains of the reference clinker caused by the transformation of the α´-belite to the β polymorph. Striae were weaker in the second and third clinkers indicating a probable stabilization of the α ‘-belite polymorph. Compressive strength of the respective cements were attained first after 28 days and the early strength did not improve with increasing fineness. Higher compressive strength values were found for the cement prepared from second clinker.Se han preparado tres clinkeres de laboratorio con altos contenidos en belita a partir de materias primas tradicionales y alternativas. El clinker de referencia se obtuvo a partir de una mezcla de caliza, arcillas arenosas y grasas y limaduras de hierro. Las arcillas grasas fueron sustituidas por polvo de ladrillo rojo en la preparación del segundo clinker, y en el tercero el contenido de arcilla grasa fue de solo un 2% y parte de la caliza fue sustituida por cascara de huevo. El estudio realizado por SEM muestra superficies estriadas alrededor de los granos de belita que indican una transformación del polimorfo α´ a la forma β-C₂S, durante el enfriamiento. Esas estrías son menos marcadas en el segundo y tercer clinker, indicando, una estabilización del polimorfo α´-C₂S. Los valores de resistencias a compresión de los correspondientes cementos, a 28 días de curado, no se ven incrementados por la finura de dichos cementos. Las mayores resistencias se obtuvieron en el cemento preparado a partir del cl

Use of pig by-products (bristles and hooves) as alternative protein raw material in fish feed

DEFF Research Database (Denmark)

Gachango, Florence Gathoni; Ekmann, K.S.; Frørup, J.

2017-01-01

Increasing growth in the aquaculture industry calls for employment of innovative technologies that will ensure sustainability in the sector, given the rising competition for feed raw material. A technology that can convert low quality biological waste resources such as pig bristles and hooves int...

Raw materials problems in connection with fast breeder type reactors

International Nuclear Information System (INIS)

Hirsch, H.; Kreusch, J.

1981-01-01

The power supply by the FBR type reactors which depends upon the availability of essential raw materials such as Cr and Mo for structural and special steels is supposed to be less ensured than supply by fossil-fueled power plants. This contribution tries to verify this statement by means of estimates of the annual Cr and Mo demand, of the resources, production and consumption as well as by a study of the possibilities of recycling and substituting Cr and Mo. The only realistic alternative to the fast breeder type reactor is supposed to be a soft path of development according to the principle of decentralization, utilization of renewable energy sources regard to environmental protection, and use of less sophisticated technology. (DG) [de

The Energy Transition and the Challenge of Critical Raw Materials

International Nuclear Information System (INIS)

Lepesant, Gilles

2018-01-01

The geopolitical analyses of energy markets are traditionally focused on fossil fuels, and less on renewable energy sources. Yet the huge development perspectives of these renewable energy sources (representing 2/3 of total net power generation capacity additions in 2016) trigger a need to take into account new challenges and vulnerabilities, related to the availability and affordability of critical raw materials, notably rare earths, which are needed to develop wind turbines, solar panels and energy storage technologies. Stakes are geopolitical, economic and environmental and are reinforced by a geography of resources and production which is concentrated within a few key countries and zones (China, Latin America, Australia, Congo mainly). The role of China in particular is at the core of the attention

Connections between borehole geophysical parameters of the quality of cement raw materials

International Nuclear Information System (INIS)

Szabo, L.; Illes, A.

1978-01-01

The raw materials for the cement industry are prospected - according to the recommendations of national authorities - by geophysical methods, too. These include not the determination of the deposit boundary, but also an estimation of the quality of limestone and clay from the point of cement manufacture. No forerunners of such tests exist, so new methods were elaborated. After 12 years of site tests it was found that the correlation between laboratory quality tests and certain geophysical parameters of clay deposits is fair but less close in case of limestone deposits. (author)

Energy potential of fruit tree pruned biomass in Croatia

Energy Technology Data Exchange (ETDEWEB)

Bilandzija, N.; Voca, N.; Kricka, T.; Martin, A.; Jurisic, V.

2012-11-01

The world's most developed countries and the European Union (EU) deem that the renewable energy sources should partly substitute fossil fuels and become a bridge to the utilization of other energy sources of the future. This paper will present the possibility of using pruned biomass from fruit cultivars. It will also present the calculation of potential energy from the mentioned raw materials in order to determine the extent of replacement of non-renewable sources with these types of renewable energy. One of the results of the intensive fruit-growing process, in post pruning stage, is large amount of pruned biomass waste. Based on the calculated biomass (kg ha{sup 1}) from intensively grown woody fruit crops that are most grown in Croatia (apple, pear, apricots, peach and nectarine, sweet cherry, sour cherry, prune, walnut, hazelnut, almond, fig, grapevine, and olive) and the analysis of combustible (carbon 45.55-49.28%, hydrogen 5.91-6.83%, and sulphur 0.18-0.21%) and non-combustible matters (oxygen 43.34-46.6%, nitrogen 0.54-1.05%, moisture 3.65-8.83%, ashes 1.52-5.39%) with impact of lowering the biomass heating value (15.602-17.727 MJ kg{sup 1}), the energy potential of the pruned fruit biomass is calculated at 4.21 PJ. (Author) 31 refs.

Calcium flouride (CaF2) from oyster shell as a raw material for thermoluminescence dosimeter

International Nuclear Information System (INIS)

Coloma, Lyra C.; Fanuga, Lyn N.; Ocreto, Cherries Ann; Rodriguez, Richita

2006-03-01

This study aims to develop a thermoluminescence dosimeter raw material made of calcium fluoride from locally available seashells that is suitable for personal radiation monitoring. Oyster shells were collected and grounded as powder samples and analyzed for calcium fluoride (CaF 2 ) content using XRF and XRD testing. Samples include pure CaF 2 , pure oyster shell, and oyster shells treated with acid. Based from the XRF results, natural oyster shell (w/ and w/o HNO 3 ) had high percentage of calcium about 49.64% and 47.45%, next to the pure calcium fluoride of 51.08%. X-ray diffractrogram shows that oyster sample had the nearest desired structure of CaF 2 compared with two seashells relative to the pure CaF 2 as standard materials. Results show that all of the natural oyster samples displayed TL emission glow curves at the temperature range 200-300 o C. It was also found that pure oyster sample has better TL response as compared to the treated ones. The researchers concluded that the calcium fluoride from oyster shells (without acid and heated) is a potentially good low-cost TLD raw material and may be used as an alternative for the much more expensive LiF dosimeters. (Authors)

Conference on raw materials and jobs cost variation - Impact on wind turbine manufacturers and operators

International Nuclear Information System (INIS)

Chabot, Bernard; Falk, Thorsten; Braeuninger, Michael; Rehfeldt, Knud; Brand, Ruth; Buhr, Ingo de; Jenne, Markus

2007-01-01

In the framework of the 2007 Husum Wind exhibition, the French-German office for Renewable energies (OFAEnR) organised a side event on In the framework of this French-German exchange of experience, participants exchanged views on raw materials and jobs cost variations in the wind power industry in both countries. Its aim was to compare and analyse the French and German respective support systems to renewable energy sources. This document brings together the available presentations (slides) made during this event: 1 - Protecting wind energy tariffs against inflation effects: analysis and suggestions from the French experience (Bernard Chabot); 2 - Wind energy in Germany - Tariff structure in the EEG renewable energy law (Thorsten Falk); 3 - Wind energy competitiveness (Michael Braeuninge, Knud Rehfeldt); 4 - Influence of raw materials price rise on the production costs of ENERCON wind turbines maker (Ruth Brand); 5 - Presentation of the overall costs of an offshore wind energy project (Ingo de Buhr); 6 - Comparison between French and German tariffs profitability using a model wind farm: presentation of the pros and cons of both systems (Markus Jenne)

Some economic aspects of the conversion of raw materials into final products

Energy Technology Data Exchange (ETDEWEB)

Pick, H J [Univ. of Aston, Birmingham, Eng.; Becker, P E

1978-01-01

In a previous paper Pick and Becker analyzed the direct and indirect relations between energy and the ''physical structure'' materials used by the engineering and construction industries. The present paper provides a more general description of materials conversion from natural resources to final products. The cost of raw materials, only some 30 percent of which come from the developing countries, accounts for a relatively small proportion of final product costs, the remaining product costs arising from the progressive application of labor, capital, energy, etc. Emphasis is placed on the complete interdependence of the inputs to manufacturing; a change in any one having implications for the remainder. Materials substitution, while in principle providing an adaptive mechanism to change, also has implications for a wide range of factors of production and for social and industrial issues such as regional employment, the demand for specific trades and professions, for research and development and for industrial structure and capital investment. Full allowance for this interdependence needs to be an integral part of effective long term policy formulation and of research and development planning.

Chemometric analysis for identification of botanical raw materials for pharmaceutical use: a case study using Panax notoginseng.

Science.gov (United States)

Zhu, Jieqiang; Fan, Xiaohui; Cheng, Yiyu; Agarwal, Rajiv; Moore, Christine M V; Chen, Shaw T; Tong, Weida

2014-01-01

The overall control of the quality of botanical drugs starts from the botanical raw material, continues through preparation of the botanical drug substance and culminates with the botanical drug product. Chromatographic and spectroscopic fingerprinting has been widely used as a tool for the quality control of herbal/botanical medicines. However, discussions are still on-going on whether a single technique provides adequate information to control the quality of botanical drugs. In this study, high performance liquid chromatography (HPLC), ultra performance liquid chromatography (UPLC), capillary electrophoresis (CE) and near infrared spectroscopy (NIR) were used to generate fingerprints of different plant parts of Panax notoginseng. The power of these chromatographic and spectroscopic techniques to evaluate the identity of botanical raw materials were further compared and investigated in light of the capability to distinguishing different parts of Panax notoginseng. Principal component analysis (PCA) and clustering results showed that samples were classified better when UPLC- and HPLC-based fingerprints were employed, which suggested that UPLC- and HPLC-based fingerprinting are superior to CE- and NIR-based fingerprinting. The UPLC- and HPLC- based fingerprinting with PCA were able to correctly distinguish between samples sourced from rhizomes and main root. Using chemometrics and its ability to distinguish between different plant parts could be a powerful tool to help assure the identity and quality of the botanical raw materials and to support the safety and efficacy of the botanical drug products.

Chemometric analysis for identification of botanical raw materials for pharmaceutical use: a case study using Panax notoginseng.

Directory of Open Access Journals (Sweden)

Jieqiang Zhu

Full Text Available The overall control of the quality of botanical drugs starts from the botanical raw material, continues through preparation of the botanical drug substance and culminates with the botanical drug product. Chromatographic and spectroscopic fingerprinting has been widely used as a tool for the quality control of herbal/botanical medicines. However, discussions are still on-going on whether a single technique provides adequate information to control the quality of botanical drugs. In this study, high performance liquid chromatography (HPLC, ultra performance liquid chromatography (UPLC, capillary electrophoresis (CE and near infrared spectroscopy (NIR were used to generate fingerprints of different plant parts of Panax notoginseng. The power of these chromatographic and spectroscopic techniques to evaluate the identity of botanical raw materials were further compared and investigated in light of the capability to distinguishing different parts of Panax notoginseng. Principal component analysis (PCA and clustering results showed that samples were classified better when UPLC- and HPLC-based fingerprints were employed, which suggested that UPLC- and HPLC-based fingerprinting are superior to CE- and NIR-based fingerprinting. The UPLC- and HPLC- based fingerprinting with PCA were able to correctly distinguish between samples sourced from rhizomes and main root. Using chemometrics and its ability to distinguish between different plant parts could be a powerful tool to help assure the identity and quality of the botanical raw materials and to support the safety and efficacy of the botanical drug products.

New raw materials for radiation curable coatings: what are they, where they come from

International Nuclear Information System (INIS)

Rybny, C.B.; Trebellas, J.C.; Vona, J.A.

1975-01-01

The availability of reasonably priced coating systems which meet the criteria of low-energy cure and minimum effluent pollution is of critical concern to the coatings industry. To appreciate the problems associated with radiation curable coatings, those manufacturing and utilizing these materials should be aware of their raw material compositions and the starting products from which they are derived. The utility and economics of ultraviolet coatings are also of prime interest. These topics are discussed, with emphasis on the photocurable polymers and their cross-linking monomers as well as the economics of this new technology in relation to energy cost savings. 7 references

High yield CTMP fibres as a possibility of the more efficient yield of wood raw material

Directory of Open Access Journals (Sweden)

Klašnja Bojana A.

2004-01-01

Full Text Available The evident shortage of wood as a raw material has become a limiting factor in the pulp and paper industry which is the greatest consumer of wood in Europe. The situation in our country is similar. During the few past years, the production of poplar and willow pulpwood was 220.000 m3 per year, which is insufficient for the planned increase in the production of sulphate pulp (175.000 tons till 2005. This paper deals with the aspects of the more efficient yield of raw material, based on the significantly higher yield of CTMP fibres, as well as with the significance of the lower adverse effect on the environment. It also analyses the conditions of production and the quality of the obtained fibres, as a possible substitute for chemical pulp and secondary fibres in papers of different quality. The main reasons for the production and use of CTMP fibres in our country are reported.

Aspects of investment protection in the case of raw material projects; Aspekte des Investitionsschutzes bei Rohstoffprojekten

Energy Technology Data Exchange (ETDEWEB)

Wolkewitz, Mathias [Wintershall Holding GmbH, Kassel (Germany). Bereich Recht, Steuern und Versicherungen; TU Clausthal (Germany). Inst. fuer Energierecht

2011-04-15

Addressing the question of investment protection currently is of particular importance under the tree aspects: (a) Due to the financial crisis and economic crisis, foreign investment in the years 2008 and 2009 have been drastically reduced; (b) There is a growing critique at the system of international investment protection; (c) For the first time, the Articles 206 and 207 of the Treaty of Lisbon of the European Union show a competence for foreign direct investment. These three aspects seem partly contradictory, but have a considerable changing potential in the area of investment protection. The author of the contribution under consideration describes the tools of investment protection as those are used for raw material projects. Subsequently the author picks out investment protection agreements and deals with some aspects that are important for practical applications in business companies. Raw material projects are projects for the exploration and production of oil and gas in foreign states.

Research on the raw material source and coloring mechanism of Jiaotan Guan porcelain in south song dynasty

International Nuclear Information System (INIS)

Zhao Weijuan; Li Guoxia; Xie Jianzhong; Guo Min; Gao Zhengyao

2004-01-01

The 28 samples from Jiaotan Guan kiln, one sample of mud material in jar from ruins of Jiaotan Guan kiln, one sample of mud material in pool of practice mud, one sample of violet-golden clay near Guan kiln and four samples of glazes and bodies of the modern imitative ancient Chinese guan porcelain were analyzed by neutron activation analysis (NAA). The contents of 36 elements in each sample were measured. The NAA data were statistically treated by fuzzy cluster method and the trend cluster diagram was obtained. The results show that the raw material origin of the bodies of Jiaotan Guan porcelain is evidently different from those of glazes, the source of raw material of bodies and glazes of Jiaotan Guan kiln are stable, and the iron is assured as main coloring element. The reflecting spectrum and main wavelength of Guan porcelain glazes are determined by color analysis instrument. The relative content of structural iron (Fe 2+ , Fe 3+ ) in the glaze and the quantitative relationship between the main wavelength of glaze in various colors are determined by Moessbauer spectrum. Thus the coloring mechanism of Guan porcelain is investigated

Sustainable prevention of resource conflicts. Raw materials supply and demand (Report 2); Rohstoffkonflikte nachhaltig vermeiden. Rohstoffe zwischen Angebot und Nachfrage (Teilbericht 2)

Energy Technology Data Exchange (ETDEWEB)

Taenzler, Dennis; Westerkamp, Meike [Adelphi Research, Berlin (Germany); Supersberger, Nikolaus; Ritthoff, Michael; Bleischwitz, Raimund [Wuppertal Institut (Germany)

2011-04-15

The demand for both energetic and non-energetic raw materials has been increasing continuously during the past few decades. Especially during the last few years, the threat of structural shortages of supply or availability came into focus. The discussion is highly controversial, especially in the case of petroleum. This sub-report presents an analysis of the supply situation of energetic and non-energetic raw materials, i.e. petroleum, coal and nuclear fuels on the one hand as well as iron and steel, chromium, nickel, cobalt, aluminium, magnesium, copper, platinum and platinum metals, industrial minerals, boron salts, phosphate, zirconium and zirconium oxide on the other hand. It is important to discuss also regional availability patterns in order to arrive at a regional picture of potential supply risks and resulting conflicts over raw materials as this is the best way to assess the danger of impending conflicts. (orig.)

A materials perspective of Martyniaceae fruits: Exploring structural and micromechanical properties.

Science.gov (United States)

Horbens, Melanie; Eder, Michaela; Neinhuis, Christoph

2015-12-01

Several species of the plant family Martyniaceae are characterised by unique lignified capsules with hook-shaped extensions that interlock with hooves and ankles of large mammals to disperse the seeds. The arrangement of fruit endocarp fibre tissues is exceptional and intriguing among plants. Structure-function-relationships of these slender, curved, but mechanically highly stressed fruit extensions are of particular interest that may inspire advanced biomimetic composite materials. In the present study, we analyse mechanical properties and fracture behaviour of the hook-shaped fruit extensions under different load conditions. The results are correlated with calculated stress distributions, the specific cell wall structure, and chemical composition, providing a detailed interpretation of the complex fruit tissue microstructure. At the cell wall level, both a large microfibril angle and greater strain rates resulted in Young's moduli of 4-9 GPa, leading to structural plasticity. Longitudinally arranged fibre bundles contribute to a great tensile strength. At the tissue level, transversely oriented fibres absorb radial stresses upon bending, whereas cells encompass and pervade longitudinal fibre bundles, thus, stabilise them against buckling. During bending and torsion, microcracks between axial fibre bundles are probably spanned analogous to a circular anchor. Our study fathoms a highly specialized plant structure, substantiating former assumptions about epizoochory as dispersal mode. While the increased flexibility allows for proper attachment of fruits during dynamical locomotion, the high strength and stability prevent a premature failure due to heavy loads exerted by the animal. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Evaluation of the biodiesel production using three sources of raw material and ethanol

Energy Technology Data Exchange (ETDEWEB)

Radecki, Angela Patricia; Fracaro, Cristiane; Gnoatto, Estor; Kavanagh, Edward; Anami, Marcelo Hidemassa; Fischborn, Marcos; Lobo, Viviane da Silva [Universidade Tecnologica Federal do Parana (UTFPR), Medianeira, PR (Brazil)], E-mail: mhanami@utfpr.edu.br; Zara, Ricardo Fiori [Prati Donaduzzi e Cia. Ltda., Toledo, PR (Brazil)

2008-07-01

The conversion of different oils in ethyl ester (biodiesel) through the transesterification with anhydrous ethanol, together with its quality and its consumption in mixture with diesel of petroleum in different ratios, they were evaluated using a stationary diesel engine connected to an electric energy generator. The raw materials used in this transformation were oil of refined soybean, oil of refined sunflower and animal fat (swine). In the transesterification reaction it was used an alkaline catalyst (sodium hydroxide), because of its proven effectiveness and the high speed facing other catalyst, beyond being less corrosive and demands less molar' reasons between the alcohol and the vegetal oil. The tests in stationary diesel engine were carried through the dilutions of 0%, 5%, 10%, 15% and 20% of biodiesel produced in mixture with diesel of petroleum. The results showed that the yield of biodiesel gotten by different sources is satisfactory. It was also observed that the basic catalysis is adjusted to the production of biodiesel from raw materials with low acidity. The tests in diesel engine appeared to be sufficiently satisfactory once it was not observed any alteration in the functioning of the engine. The consumption was also not modified by the studied dilutions, demonstrating that the biodiesel can be added to the pure diesel reducing the use of the fuel derived from petroleum. (author)

SESQUITERPENE LACTONES OF LEAVES AND FRUITS OF LAURUS NOBILIS L.

Directory of Open Access Journals (Sweden)

D. A. Konovalov

2014-01-01

Full Text Available Bay laurel (Laurus nobilis L. is common in the Mediterranean region, Europe and America. Widely cultivated in the countries of the Arabian Peninsula and North Africa. As the basic active substances in plants: essential oil components, sesquiterpene lactones, alkaloids, and phenolic compounds (flavonoids, phenolic acids and lignans are described.In the plant more than 30 sesquiterpene lactones are found. Structural types of these compounds include eudesmanolides, germacranolides, guaianolides.Sesquiterpene lactones isolated from the leaves and fruits of Laurus nobilis, possess antibacterial, antifungal, anti-diabetic, anti-inflammatory, hepatoprotective, neuroprotective and cytotoxic activity. They inhibit the absorption of alcohol increases the activity of hepatic glutathione-S-transferase. Most of these types of activity of sesquiterpene lactones from laurel due to the presence within their structure of α-methylene--butyrolactone part.Thus, sesquiterpene lactones-containing leaves and fruits Laurus nobilis could have been an important source of raw materials for the creation of new medicines

Influence of raw material properties on energy consumption during briquetting process

Directory of Open Access Journals (Sweden)

Ivanova Tatiana

2018-01-01

Full Text Available Biomass is doubtless a very significant source of renewable energy being worldwide abundant with high energy potential. This paper deals with assessment energy consumption at especially grinding and briquetting processes, which should result in essential economy of energy at solid biofuel production. Various types of raw materials were used at the experiment such as hemp (Cannabis sativa L. biomass, two species of Miscanthus (Miscanthus sinensis, Miscanthus x gigantheus and apple wood biomass. These materials were dried, grinded and pressed by piston press having pressing chamber diameter of 65 mm. Materials were grinded into three fractions (4 mm, 8 mm and 12 mm. Material throughput (kg.h-1 and energy consumption (kWh.t-1 were registered. As to results: the highest throughput at both grinding cases as well as briquetting was found at apple wood biomass; however the energy consumption during briquetting of apple wood was relatively high. The worst results concerning throughput and energy consumption (especially at briquetting were found at hemp biomass. Nevertheless, briquettes made of hemp had the best mechanical durability. Both Miscunthus species (herbaceous biomass have very similar parameters and showed quite good relation between throughput and energy consumption at the used machines.

Microbiological profile and nutritional quality of raw foods for neutropenic patients under hospital care

OpenAIRE

Galati, Paula Cristina; Lataro, Renata Cristina; Souza, Vanessa Maciel; de Martinis, Elaine Cristina Pereira; Chiarello, Paula Garcia

2013-01-01

Objective This study aimed to analyze and compare the microbiological profile and vitamin C content of raw and cooked foods destined for neutropenic inpatients. Methods Three vegetables and nine fruits, raw and boiled, washed and sanitized were examined. Heat-tolerant coliforms and coagulase-positive staphylococci were counted and the presence of Salmonella spp was investigated. The vitamin C content was analyzed by a colorimetric reaction. The Statistical Package for Social Sciences (SPSS) s...

Microbiological profile and nutritional quality of raw foods for neutropenic patients under hospital care

OpenAIRE

Galati, Paula Cristina; Lataro, Renata Cristina; Souza, Vanessa Maciel; Martinis, Elaine Cristina Pereira de; Chiarello, Paula Garcia

2013-01-01

OBJECTIVE: This study aimed to analyze and compare the microbiological profile and vitamin C content of raw and cooked foods destined for neutropenic inpatients. METHODS: Three vegetables and nine fruits, raw and boiled, washed and sanitized were examined. Heat-tolerant coliforms and coagulase-positive staphylococci were counted and the presence of Salmonella spp was investigated. The vitamin C content was analyzed by a colorimetric reaction. The Statistical Package for Social Sciences (SPSS)...

Radioactive contaminants in raw materials and foodstuffs of plant origin

International Nuclear Information System (INIS)

Stankovicj, S.; Krainchanicj, M.; Stankovicj, A.

1990-01-01

The paper concentrates on the results of activity level of radioactive caesium 134 and 137 in the samples of raw materials (barley, oats, soybean, sunflower, pumpkin seed, hops, shreded sugar beet, maize), animal feedstuffs (alfalfa, alfalfa meal, rape, concentrates fed to chickens, pigs or bpvines, dry turnip shreds) and foodstuff of plant origin (lettuce, spinach, cabbage, carrot, celery, cucumber, tomato, olives, sesame). All samples - produced locally on the major part but also including some imported stuff -have been subjected to continuous gamma spectrometry starting with the Chernobyl accident in 1986 through 1989. The highest activity of caesium was recorded in the samples of animal feedstuffs (alfalfa, alfalfa meal, rape) in the years 1986 and 1987. In time, however, the activity tends to drop considerably. (author) 4 refs.; 3 tabs

Utilisation of biological and secondary raw materials IX. Recycling - conversion to energy

International Nuclear Information System (INIS)

Wiemer, Klaus; Kern, Michael; Raussen, Thomas

2014-01-01

The book on the utilization of biological and secondary raw materials covers the following issues: Perspectives of the circular flow and resource economy, waste avoidance, closed substance cycle waste management law and biowaste assessment, economic evaluation and usage alternatives for biogas, consequences of the 4th BlmschV, the BioAbfV and the DueV for the biowaste treatment, alternative techniques of the Biowaste collection, alternative models of the recyclable substance assessment, future of the packaging and recyclable substance utilization, ElectroG and E-scrape recycling, innovative concepts for the municipal waste management, future of the MBA, MVA and EBS management.

Genetic resources of autochthonous fruit species and varieties

Directory of Open Access Journals (Sweden)

Keserović Zoran

2017-01-01

Full Text Available The paper describes the plentitude of genetic resources of indigenous varieties of fruit species and their importance for further development of fruit growing, especially from the aspect of breeding new varieties resistant to pathogens and abiotic stress conditions (frost, drought, sunburns, etc.. Economic significance and importance in the human nutrition, as a raw or processed fruitage, were stated as well. Based on the unique biodiversity, the Balkan Peninsula can be considered as a secondary center of divergence for a large number of fruit species, such as Malus x domestica, Malus sylvestris, Pyrus communis, Prunus cerasifera, P. persica, P. armeniaca, P. fruticosa, P. amygdalus, P. nana, Juglans regia, Corilus colurna, Corilus avellana, Castanea sativa, Fragaria vesca, Cornus mas. The old indigenous and domesticated varieties and natural populations of fruit species on the Balkan Peninsula have never been the subject of comprehensive research work on their collecting and studying. Serbia has no national scientific institution that takes care of genetic resources. Nowadays, the issue of preserving genetic resources is of great importance because, due to the intensification and modernization of plant production, many local populations have disappeared or are reduced to a small number of biotypes. The varieties with huge genetic and breeding value have disappeared forever without any possibility of their return. By importing high quality fruit varieties, we imported many diseases and various pests as well. New varieties intended for intensive cultivation require the application of expensive growing technologies. The systematic scientific work on the study of wild fruit species and autochthonous varieties is of the great interest for fruit science and practice in the future. The establishment of in situ collections with the aim to preserve valuable genetic material is mandatory. In the following period, indigenous and domesticated varieties

Solid-State (13)C NMR Delineates the Architectural Design of Biopolymers in Native and Genetically Altered Tomato Fruit Cuticles.

Science.gov (United States)

Chatterjee, Subhasish; Matas, Antonio J; Isaacson, Tal; Kehlet, Cindie; Rose, Jocelyn K C; Stark, Ruth E

2016-01-11

Plant cuticles on outer fruit and leaf surfaces are natural macromolecular composites of waxes and polyesters that ensure mechanical integrity and mitigate environmental challenges. They also provide renewable raw materials for cosmetics, packaging, and coatings. To delineate the structural framework and flexibility underlying the versatile functions of cutin biopolymers associated with polysaccharide-rich cell-wall matrices, solid-state NMR spectra and spin relaxation times were measured in a tomato fruit model system, including different developmental stages and surface phenotypes. The hydrophilic-hydrophobic balance of the cutin ensures compatibility with the underlying polysaccharide cell walls; the hydroxy fatty acid structures of outer epidermal cutin also support deposition of hydrophobic waxes and aromatic moieties while promoting the formation of cell-wall cross-links that rigidify and strengthen the cuticle composite during fruit development. Fruit cutin-deficient tomato mutants with compromised microbial resistance exhibit less efficient local and collective biopolymer motions, stiffening their cuticular surfaces and increasing their susceptibility to fracture.

Characterization of a wollastonite glass-ceramic material prepared using sugar cane bagasse ash (SCBA) as one of the raw materials

Energy Technology Data Exchange (ETDEWEB)

Teixeira, Silvio R., E-mail: rainho@fct.unesp.br [Universidade Estadual Paulista — UNESP, Faculdade de Ciências e Tecnologia — FCT, 19060-900 Presidente Prudente — SP (Brazil); Souza, Agda E. [Universidade Estadual Paulista — UNESP, Faculdade de Ciências e Tecnologia — FCT, 19060-900 Presidente Prudente — SP (Brazil); Carvalho, Claudio L.; Reynoso, Victor C.S. [Universidade Estadual Paulista — UNESP, Faculdade de Engenharia de Ilha Solteira — FEIS, 15385-000 Ilha Solteira – SP (Brazil); Romero, Maximina; Rincón, Jesús Ma. [Instituto de Ciencias de la Construccion Eduardo Torroja — IETCC, CSIC, 28033 Madrid (Spain)

2014-12-15

Glass-ceramic material prepared with sugar cane bagasse ash as one of the raw materials was characterized to determine some important properties for its application as a coating material. X-ray diffraction patterns showed that wollastonite-2M (CaSiO{sub 3}) was the major glass-ceramic phase. The Rietveld method was used to quantify the crystalline (60 wt.%) and vitreous (40 wt.%) phases in the glass-ceramic. The microstructure (determined by scanning electron microscopy) of this material had a marble appearance, showing a microporous network of elongated crystals with some areas with dendritic, feather-like ordering. Microhardness data gave a mean hardness value of 564.4 HV (Vickers-hardness), and light microscopy disclosed a greenish brown colored material with a vitreous luster. - Highlights: • We studied the properties of a glass-ceramic material obtained from sugarcane ash. • This material has the appearance and hardness of natural stones. • A refining method gave information about its amorphous and crystalline phases. • This material has potential to be used as coating plates for buildings.

Characterization of a wollastonite glass-ceramic material prepared using sugar cane bagasse ash (SCBA) as one of the raw materials

International Nuclear Information System (INIS)

Teixeira, Silvio R.; Souza, Agda E.; Carvalho, Claudio L.; Reynoso, Victor C.S.; Romero, Maximina; Rincón, Jesús Ma.

2014-01-01

Glass-ceramic material prepared with sugar cane bagasse ash as one of the raw materials was characterized to determine some important properties for its application as a coating material. X-ray diffraction patterns showed that wollastonite-2M (CaSiO 3 ) was the major glass-ceramic phase. The Rietveld method was used to quantify the crystalline (60 wt.%) and vitreous (40 wt.%) phases in the glass-ceramic. The microstructure (determined by scanning electron microscopy) of this material had a marble appearance, showing a microporous network of elongated crystals with some areas with dendritic, feather-like ordering. Microhardness data gave a mean hardness value of 564.4 HV (Vickers-hardness), and light microscopy disclosed a greenish brown colored material with a vitreous luster. - Highlights: • We studied the properties of a glass-ceramic material obtained from sugarcane ash. • This material has the appearance and hardness of natural stones. • A refining method gave information about its amorphous and crystalline phases. • This material has potential to be used as coating plates for buildings

Derivation of general expression for variance in difference in the contents of active ingredient in raw material as determined at seller's and purchaser's site

International Nuclear Information System (INIS)

Narasimha Murty, B.; Prahlad, B.

2012-01-01

Material supply from a supplier to purchaser involve weighing of the material at both the sites. It is always of interest to know whether there is any difference in the weight of the material and more importantly in the weight of the active ingredient supplied and received. This paper describes the derivation of general expression for variance in difference in the contents of active ingredient in raw material as determined at the seller's and purchaser's site. The derived expression for the variance in difference in the content of active ingredient as determined at seller's and purchaser's site is a generic one though its application is demonstrated for two raw materials

Diallel analysis of fruit set in Hevea brasiliensis Muell. Arg.

Directory of Open Access Journals (Sweden)

Kenneth O. Omokhafe

2007-03-01

Full Text Available The clonal and inter-clonal combining ability of fruit set in a Hevea brasiliensis four-parent diallel mating was evaluated using a randomized complete block experimental design with three replicates. Twelve main and reciprocal crosses were hand pollinated and percentage fruit set was recorded. The raw data were subjected to an arc-sine transformation for analysis of variance, and general and specific combining ability. There was significant variation of each of fruit set for the various crosses, general combining ability and reciprocal effect. The breeding implications of these results are also discussed.

Different Disinfectants Efficiency of Fruits and Vegetables Available in Market of

Directory of Open Access Journals (Sweden)

Abdollah Dargahi

2013-11-01

Full Text Available The fruits and vegetables are carrier microbial flora and in every stage of production, transportation, packaging, storage and sale to consumers are exposed to microbial contamination. Raw fruits and vegetables are suitable place for growing a variety of parasites and bacteria such as Shigella, Pseudomonas aeruginosa and Campylobacter that many of theirs can cause epidemic if the conditions have provide.

Cutin from agro-waste as a raw material for the production of bioplastics.

Science.gov (United States)

Heredia-Guerrero, José A; Heredia, Antonio; Domínguez, Eva; Cingolani, Roberto; Bayer, Ilker S; Athanassiou, Athanassia; Benítez, José J

2017-11-09

Cutin is the main component of plant cuticles constituting the framework that supports the rest of the cuticle components. This biopolymer is composed of esterified bi- and trifunctional fatty acids. Despite its ubiquity in terrestrial plants, it has been underutilized as raw material due to its insolubility and lack of melting point. However, in recent years, a few technologies have been developed to obtain cutin monomers from several agro-wastes at an industrial scale. This review is focused on the description of cutin properties, biodegradability, chemical composition, processability, abundance, and the state of art of the fabrication of cutin-based materials in order to evaluate whether this biopolymer can be considered a source for the production of renewable materials. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Titanium. Properties, raw datum surface, physicochemical basis and fabrication technique

International Nuclear Information System (INIS)

Garmata, V.A.; Petrun'ko, A.N.; Galitskij, N.V.; Olesov, Yu.G.; Sandler, R.A.

1983-01-01

On the nowadays science and technology achievements the complex of titanium metallurgy problems comprising raw material base, physico-chemical basis and fabrication technique, properties and titanium usage fields is considered for the first time. A particular attention is given to raw material base, manufacturing titanium concentrates and titanium tetrachloride, metallothermal reduction, improvement of metal quality. Data on titanium properties are given, processes of titanium powder metallurgy, scrap and waste processing, problems of economics and complex raw material use are considered

Accuracy increasing in the nuclear-physical analysis of mineral raw materials of heterogeneous composition

International Nuclear Information System (INIS)

Pak, Yu.; Vdovkin, A.; Pak, D.

2002-01-01

the analysis of heterogeneous raw material by the gamma-albedo method it's necessary to optimize the primary gamma-radiation energy choose depending on the material composition of the raw material, its granulometric composition and to reach the maximal presentability of the analysis. For this a method has been suggested which allows to increase substantially the effective study surface without increasing the analyzed object size. The essence of the method consists in the rotation of the object around its axis relatively to the detector reciprocating parallel to the sample in the process of measuring. The optimal laws of the detector motion and the sample rotation provide for the equal presentability of each unit study surface. The experimental approving of the suggested method showed that the optimization of the methodical and geometrical control parameters in the dynamic measuring conditions allow to increase the accuracy of the analysis of disperse raw materials more that twice as large

Climate changes, raw materials shortage, and economic development