WorldWideScience

Sample records for rapid-curing clear acrylic

  1. Surface modification of nanoparticles for radiation curable acrylate clear coatings

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, F. E-mail: fbauer@rz.uni-leipzig.de; Glaesel, H.-J.; Hartmann, E.; Bilz, E.; Mehnert, R

    2003-08-01

    To obtain transparent, scratch and abrasion resistant coatings a high content of nanosized silica and alumina filler was embedded in radiation-curable acrylate formulations by acid catalyzed silylation using trialkoxysilanes. {sup 29}SiMAS NMR and MALDI-TOF mass spectrometry were employed to elucidate the structure of the surface-grafted methacryloxypropyl-, vinyl- and n-propyl-trimethoxysilane. In accordance with NMR findings, MALDI-TOF MS showed highly condensed oligomeric siloxanes of more than 20 monomeric silane units. A ladder-like structure of bound polysiloxanes is proposed rather than a simplified picture of tridentate silane bonding. Hence, silane coupling agents do not only modify the chemical nature of the filler surface but also strongly effect the rheological properties of the acrylate nanodispersions.

  2. The fabrication of wavelength shifting lightguides from clear acrylic sheet by disperse dyeing

    Science.gov (United States)

    McMillan, J. E.

    2015-06-01

    Wavelength shifting lightguides have found extensive use as a means of collecting scintillation or cherenkov light from large areas onto a smaller area photodetector and for matching the emitted spectrum to the spectral response of the photodetector. Conventionally, such lightguides are fabricated by casting acrylic polymer with the fluorescent dye incorporated in the bulk. A technique has been developed in which plain cast acrylic sheet is disperse dyed in an aqueous bath. The resulting lightguide has the fluorescent dye held in a thin layer at the surface of the material. A number of different fluorescent dyes are demonstrated

  3. Comparison of efficacy of sodium hypochlorite with sodium perborate in removal of stains from heat-cured clear acrylic resin.

    Science.gov (United States)

    Mathai, Joseph Robin; Sholapurkar, Amar A; Raghu, Aparna; Shenoy, Revathi P; Mallya, H Madhukar; Pai, Keerthilatha M; D'Souza, Mariette

    2011-01-01

    Acrylic resin bases of removable dentures attract stains and odor-producing organic and inorganic deposits. The use of chemical denture cleanser soaks is the most popular method of denture cleansing. This study was undertaken to compare the efficacy of two different denture cleansers--sodium perborate (Clinsodent) and sodium hypochlorite (VI-Clean)--in removing tea, coffee, turmeric and tobacco (paan) stains from heat-cured clear acrylic resins. Distilled water was used as a control. Both Clinsodent and VI-Clean were found to be the least effective in removing coffee stains and best for removing turmeric stain. It is necessary that the dental professional be aware of these results to ensure that denture wearers know how to select the appropriate denture cleanser.

  4. Silicone/Acrylate Copolymers

    Science.gov (United States)

    Dennis, W. E.

    1982-01-01

    Two-step process forms silicone/acrylate copolymers. Resulting acrylate functional fluid is reacted with other ingredients to produce copolymer. Films of polymer were formed by simply pouring or spraying mixture and allowing solvent to evaporate. Films showed good weatherability. Durable, clear polymer films protect photovoltaic cells.

  5. Rapidly curable electrically conductive clear coatings

    Energy Technology Data Exchange (ETDEWEB)

    Bowman, Mark P.; Anderson, Lawrence G.; Post, Gordon L.

    2018-01-16

    Rapidly curable electrically conductive clear coatings are applied to substrates. The electrically conductive clear coating includes to clear layer having a resinous binder with ultrafine non-stoichiometric tungsten oxide particles dispersed therein. The clear coating may be rapidly cured by subjecting the coating to infrared radiation that heats the tungsten oxide particles and surrounding resinous binder. Localized heating increases the temperature of the coating to thereby thermally cure the coating, while avoiding unwanted heating of the underlying substrate.

  6. Occupational contact allergy to (meth)acrylates.

    Science.gov (United States)

    Geukens, S; Goossens, A

    2001-03-01

    Among 13,833 patients suspected of contact dermatitis examined during the years 1978-1999, occupational contact allergy to (meth)acrylates was diagnosed in 31 patients. The 3 most common sensitizers were ethyleneglycol dimethacrylate (17 positive patch tests), 2-hydroxyethyl methacrylate (14) and triethyleneglycol dimethacrylate (6). The aim of this report was to assess the different occupations and industries responsible for occupational sensitization to (meth)acrylates. 14 of the 31 patients work in the dental sector, either as a dentist or as a student of dental technology, where (meth)acrylate-containing dental prostheses and dental composites are mainly responsible for allergy to (meth)acrylates. An increasing trend in dermatological problems related to the expansion of the use of (meth)acrylates is clearly reflected in the patient population of our dermatology department.

  7. Acrylates in contact dermatitis.

    Science.gov (United States)

    Sasseville, Denis

    2012-01-01

    Acrylates are plastic materials that are formed by the polymerization of monomers derived from acrylic or methacrylic acid. They have found numerous applications in paints, varnishes and adhesives, in the printing industry, in the medical and dental professions, and in artificial nails. Beginning in the 1950s, many reports of occupational and nonoccupational allergic contact dermatitis to (meth)acrylate monomers have been published. These molecules are strong irritants, and patch testing can induce active sensitization. When patch tested, acrylate-allergic patients often display multiple positive tests. These reactions may represent cross-reactions, or concomitant reactions due to the presence, in the products responsible for sensitization, of impurities not disclosed in material safety data sheets. (Meth)acrylates are volatile and unstable chemicals, as demonstrated by their rapid disappearance from commercially available patch test allergens when exposed to air for more than a few hours.

  8. Acrylate contact allergy: patient characteristics and evaluation of screening allergens.

    Science.gov (United States)

    Drucker, Aaron Mark; Pratt, Melanie Dawn

    2011-01-01

    Acrylates are present in a wide variety of products and cause occupational and non-occupational allergic contact dermatitis. There is no clear guidance from the literature as to which allergens should be used for patch-test screening for acrylates. To characterize patients with contact allergy to acrylates and to evaluate the allergens used to screen for acrylate allergy. Charts of patients visiting an outpatient contact dermatitis clinic from January 1998 to February 2008 were reviewed retrospectively. Forty-four patients were found to have contact allergy to acrylates. The most commonly positive allergens were hydroxyethyl methacrylate (HEMA), ethyl acrylate (EA), and methyl methacrylate (MMA). Thirty-two of the 44 positive patch-test results (73%) would have been discovered with the use of the two compounds (MMA, EA) in the North American Standard Series (Chemotechnique screening series), a commercially available screening series, while 12 were found through expanded patch testing. Artificial nails, dental materials, and adhesives were the most common exposures. Occupational relevance was found in 18 cases, including those of dental workers, assemblers, and aestheticians. Acrylates are an important cause of contact allergy. Screening series identify most cases of acrylate allergy but miss a substantial number. Clinicians should remain vigilant for acrylate allergy even if initial screening is negative.

  9. Clear retainer

    Directory of Open Access Journals (Sweden)

    Priyakorn Chaimongkol

    2017-01-01

    Full Text Available A clear retainer is a removable retainer that is popular in the present day. Compared with conventional fixed and removable orthodontic retainers, it is a more esthetic, comfortable, and inexpensive appliance. Although several studies have been published about clear retainers, it could be difficult to interpret the results because of the variety of study designs, sample sizes, and research methods. This article is intended to compile the content from previous studies and discuss advantages, disadvantages, fabrication, insertion, and adjustment. Moreover, the effectiveness in maintaining dental position, occlusion, retention protocols, thickness, and survival rate of clear retainers is discussed.

  10. Effects of Novel Structure Bonding Materials on Properties of Aeronautical Acrylic

    Directory of Open Access Journals (Sweden)

    LI Zhisheng

    2017-06-01

    Full Text Available Novel structure bonding materials, J-351 epoxy adhesive film with low curing temperature and liquid modified acrylate SY-50s adhesive were chosen and characterized. The effects of adhesives on the mechanical properties of acrylic were studied. The results reveal that both adhesives have excellent bonding properties to acrylic. The stress-solvent crazing value of J-351 is higher than that of SY-50s. With the application of adhesive on the surface, mechanical properties of acrylic are declined. Casting acrylic shows more drastic decline than that of oriented acrylic. Through the characterization of fracture surface, we find that fracture of tensile sample derives from the side with adhesive. Mechanical properties of acrylic are more sensitive to SY-50s, because the liquid adhesive presents integrate bonding interface with acrylic. The interface between J-351 and acrylic is clear, making acrylic insensitive to J-351 film. Edge attachment strength of samples bonded with J-351 are higher than that of samples bonded with SY-50s due to the effects of adhesives on acrylic. J-351 epoxy adhesive film presents preferable application performance in the structure bonding of aeronautical acrylic.

  11. Acrylic mechanical bond tests

    Energy Technology Data Exchange (ETDEWEB)

    Wouters, J.M.; Doe, P.J.

    1991-02-01

    The tensile strength of bonded acrylic is tested as a function of bond joint thickness. 0.125 in. thick bond joints were found to posses the maximum strength while the acceptable range of joints varied from 0.063 in. to almost 0.25 in. Such joints are used in the Sudbury Neutrino Observatory.

  12. Hyperbranched urethane-acrylates

    Directory of Open Access Journals (Sweden)

    Tasić Srba

    2004-01-01

    Full Text Available The synthesis, characterization and UV-curing of hyperbranched urethaneacrylates (HB-UA were investigated in this study. They were evaluated as oli-gomers in model UV curable coatings. HB-UAs were synthesized by reaction of an aliphatic hyperbranched polyester of the second generation (HBRG2 and an isocyanate adduct, obtained by the reaction of isophoronediisocyana-te and different hydroxy alkyl acrylates. Their thermal properties and viscosities depend on the degree of modification of HBRG2 and the type of hydroxy alkyl acrylate used. The introduction of a flexible alkoxylated spacer between the HBP core and acrylate end groups reduces steric hindrance by moving the cross linkable acrylate groups away from the HBP core and increase its reactivity. Due to the presence of abstractable H-atoms in the α-position to the ether links, HB-UAs based on poly(ethylene oxide monoacrylate are very reactive and do not show oxygen inhibition. The obtained coatings combine a high cross linking density with flexible segments between the cross links, which results in a good compromise between hardness and flexibility and have the potential to be used in different UV-curing applications.

  13. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance with...

  14. [Acrylic resin removable partial dentures

    NARCIS (Netherlands)

    Baat, C. de; Witter, D.J.; Creugers, N.H.J.

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of

  15. [Acrylic resin removable partial dentures].

    Science.gov (United States)

    de Baat, C; Witter, D J; Creugers, N H J

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of removable partial dentures, the acrylic resin removable partial denture has 3 favourable aspects: the economic aspect, its aesthetic quality and the ease with which it can be extended and adjusted. Disadvantages are an increased risk of caries developing, gingivitis, periodontal disease, denture stomatitis, alveolar bone reduction, tooth migration, triggering of the gag reflex and damage to the acrylic resin base. Present-day indications are ofa temporary or palliative nature or are motivated by economic factors. Special varieties of the acrylic resin removable partial denture are the spoon denture, the flexible denture fabricated of non-rigid acrylic resin, and the two-piece sectional denture. Furthermore, acrylic resin removable partial dentures can be supplied with clasps or reinforced by fibers or metal wires.

  16. Cross-sensitization patterns in acrylate allergies.

    Science.gov (United States)

    Jordan, W P

    1975-01-01

    Five subjects developed allergic contact dermatitis to one or more acrylate components used in a commercial adhesive tape. Patch testing to acrylic monomers was performed to examine their cross-reaction patterns. Two subjects with broad cross-reactions to acrylates did not react to methyl methacrylate or the alkyl methacrylate that corresponded to the acrylate which induced the sensitization. Methyl methacrylate may not be adequate as a screen for many acrylates used commercially.

  17. Two decades of occupational (meth)acrylate patch test results and focus on isobornyl acrylate

    NARCIS (Netherlands)

    Christoffers, Wietske A; Coenraads, Pieter Jan; Schuttelaar, Marie-Louise A

    BACKGROUND: Acrylates constitute an important cause of occupational contact dermatitis. Isobornyl acrylate sensitization has been reported in only 2 cases. We encountered an industrial process operator with occupational contact dermatitis caused by isobornyl acrylate. OBJECTIVES: (i) To investigate

  18. Two decades of occupational (meth)acrylate patch test results and focus on isobornyl acrylate

    OpenAIRE

    Christoffers, Wietske A; Coenraads, Pieter Jan; Schuttelaar, Marie-Louise A

    2013-01-01

    BACKGROUND: Acrylates constitute an important cause of occupational contact dermatitis. Isobornyl acrylate sensitization has been reported in only 2 cases. We encountered an industrial process operator with occupational contact dermatitis caused by isobornyl acrylate. OBJECTIVES: (i) To investigate whether it is relevant to add isobornyl acrylate to the (meth)acrylate test series. (ii) To report patients with (meth)acrylate contact allergy at an occupational dermatology clinic. PATIENTS/MATER...

  19. Bonding auto-polymerising acrylic resin to acrylic denture teeth.

    LENUS (Irish Health Repository)

    Nagle, Susan

    2009-09-01

    This study investigated the effect of surface treatments on the shear bond strength of an auto-polymerising acrylic resin cured to acrylic denture teeth. The surface treatments included a combination of grit-blasting and\\/or wetting the surface with monomer. Samples were prepared and then stored in water prior to shear testing. The results indicated that the application of monomer to the surface prior to bonding did not influence the bond strength. Grit blasting was found to significantly increase the bond strength.

  20. 40 CFR 721.2805 - Acrylate ester.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under this...

  1. Isobornyl acrylate contact allergy: Rare or underdiagnosed?

    NARCIS (Netherlands)

    Christoffers, W.A.; Coenraads, P.J.; Schuttelaar, M.L.A.

    2012-01-01

    Background: Allergic contact dermatitis to isobornyl acrylate has been reported in only two cases in literature. Therefore, isobornyl acrylate is not part of a (meth) acrylates patch test series. At our department an industrial worker presented with therapy-resistant hand eczema and sensitizations

  2. Concepts for stereoselective acrylate insertion

    KAUST Repository

    Neuwald, Boris

    2013-01-23

    Various phosphinesulfonato ligands and the corresponding palladium complexes [{((PaO)PdMeCl)-μ-M}n] ([{( X1-Cl)-μ-M}n], (PaO) = κ2- P,O-Ar2PC6H4SO2O) with symmetric (Ar = 2-MeOC6H4, 2-CF3C6H4, 2,6-(MeO)2C6H3, 2,6-(iPrO)2C 6H3, 2-(2′,6′-(MeO)2C 6H3)C6H4) and asymmetric substituted phosphorus atoms (Ar1 = 2,6-(MeO)2C6H 3, Ar2 = 2′-(2,6-(MeO)2C 6H3)C6H4; Ar1 = 2,6-(MeO)2C6H3, Ar2 = 2-cHexOC 6H4) were synthesized. Analyses of molecular motions and dynamics by variable temperature NMR studies and line shape analysis were performed for the free ligands and the complexes. The highest barriers of ΔGa = 44-64 kJ/mol were assigned to an aryl rotation process, and the flexibility of the ligand framework was found to be a key obstacle to a more effective stereocontrol. An increase of steric bulk at the aryl substituents raises the motional barriers but diminishes insertion rates and regioselectivity. The stereoselectivity of the first and the second methyl acrylate (MA) insertion into the Pd-Me bond of in situ generated complexes X1 was investigated by NMR and DFT methods. The substitution pattern of the ligand clearly affects the first MA insertion, resulting in a stereoselectivity of up to 6:1 for complexes with an asymmetric substituted phosphorus. In the consecutive insertion, the stereoselectivity is diminished in all cases. DFT analysis of the corresponding insertion transition states revealed that a selectivity for the first insertion with asymmetric (P aO) complexes is diminished in the consecutive insertions due to uncooperatively working enantiomorphic and chain end stereocontrol. From these observations, further concepts are developed. © 2012 American Chemical Society.

  3. Solvent effects on acrylate kp in organic media?-A systematic PLP-SEC study.

    Science.gov (United States)

    Haehnel, Alexander P; Wenn, Benjamin; Kockler, Katrin; Bantle, Tobias; Misske, Andrea M; Fleischhaker, Friederike; Junkers, Thomas; Barner-Kowollik, Christopher

    2014-12-01

    The Arrhenius parameters of the propagation rate coefficient, kp , are determined employing high-frequency pulsed laser polymerization-size exclusion chromatography (PLP-SEC) for the homologous series of five linear alkyl acrylates (i.e., methyl acrylate (MA), butyl acrylate (BA), dodecyl acrylate (DA), stearyl acrylate (SA), and behenyl acrylate (BeA)) in 1 m solution in butyl acetate (BuAc) as well as in toluene. The comparison of the obtained kp values with the literature known values for bulk demonstrates that no significant solvent influence neither in BuAc nor in toluene on the propagation reaction compared to bulk is detectable. Concomitantly, the kp values in toluene and in BuAc solution display a similar increase with increasing number of C-atoms in the ester side chain as was previously reported for the bulk systems. These findings are in clear contrast to earlier studies, which report a decrease of kp with increasing ester side chain length in toluene. The additional investigation of the longest and shortest ester side chain acrylate (i.e., BeA and MA) over the entire experimentally available concentration range at one temperature (i.e., 50 °C) does not reveal any general concentration dependence and all observed differences in the kp are within the experimental error. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Two decades of occupational (meth)acrylate patch test results and focus on isobornyl acrylate.

    Science.gov (United States)

    Christoffers, Wietske A; Coenraads, Pieter-Jan; Schuttelaar, Marie-Louise A

    2013-08-01

    Acrylates constitute an important cause of occupational contact dermatitis. Isobornyl acrylate sensitization has been reported in only 2 cases. We encountered an industrial process operator with occupational contact dermatitis caused by isobornyl acrylate. (i) To investigate whether it is relevant to add isobornyl acrylate to the (meth)acrylate test series. (ii) To report patients with (meth)acrylate contact allergy at an occupational dermatology clinic. Our patch test database was screened for positive reactions to (meth)acrylates between 1993 and 2012. A selected group of 14 patients was tested with an isobornyl acrylate dilution series: 0.3%, 0.1%, 0.033%, and 0.01%. Readings were performed on D2, D3, and D7. One hundred and fifty-one patients were tested with our (meth)acrylate series; 24 had positive reactions. Most positive reactions were to 2-hydroxypropyl acrylate, 2-hydroxyethyl acrylate, 2-hydroxypropyl methacrylate, and diethyleneglycol diacrylate. Hypothetical screening with 2-hydroxypropyl acrylate, ethyleneglycol dimethacrylate, ethoxylated bisphenol A glycol dimethacrylate and trimethylolpropane triacrylate identified 91.7% of the 24 patients. No positive reactions were observed in 14 acrylate-positive patients tested with the isobornyl acrylate dilution series. The 0.3% isobornyl acrylate concentration induced irritant reactions in 3 patients. We report a rare case of allergic contact dermatitis caused by isobornyl acrylate. However, this study provides insufficient support for isobornyl acrylate to be added to a (meth)acrylate series. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  5. Visual performance of acrylic and PMMA intraocular lenses.

    Science.gov (United States)

    Gozum, N; Unal, E Safgonul; Altan-Yaycioglu, R; Gucukoglu, A; Ozgun, C

    2003-03-01

    To evaluate the quality of visual functions after cataract surgery and intraocular lens (IOL) implantation with different lens materials and compare the results with age-matched subjects with clear phakic eyes. Control and pseudophakic groups involved individuals aged between 50 and 75 years, without any accompanying ocular or systemic disease. In all, 50 eyes implanted with foldable acrylic IOLs, and 41 eyes implanted with polymethyl-methacrylate (PMMA) IOLs were compared with 45 phakic eyes as controls. Visual functions were evaluated for contrast sensitivity function and glare disability. The results were compared statistically using one-way analysis of variance (ANOVA). At high luminance levels, the difference among groups for contrast sensitivity was statistically significant for all spatial frequencies (P0.05). Glare disability scores were significantly higher in the PMMA-IOL group compared to the control and acrylic-IOL groups. The visual quality achieved in pseudophakic eyes was not as good as in clear phakic eyes in regard to contrast sensitivity and glare. However, acrylic IOLs fared better than PMMA IOLs.

  6. In vitro cytotoxicity of self-curing acrylic resins of different colors.

    Science.gov (United States)

    Retamoso, Luciana Borges; da Cunha, Taís de Morais Alves; Pithon, Matheus Melo; dos Santos, Rogério Lacerda; Martins, Fernanda Otaviano; Romanos, Maria Teresa Villela; Tanaka, Orlando Motohiro

    2014-01-01

    The aim of this study was to assess the in vitro cytotoxicity of acrylic resins of different colors over time. Specimens were divided into 4 groups (n = 6) according to the color of the acrylic resin (Orto Class, Clássico, Campinas, São Paulo, Brazil): Group 1, clear acrylic resin; Group 2, pink acrylic resin; Group 3, blue acrylic resin; and Group 4, green acrylic resin. All specimens were fabricated according to the mass manipulation technique and submitted to mechanical polishing protocol. The control was performed with an amalgam specimen (C+), a glass specimen (C-) and cell control (CC). Specimens were immersed in Minimum Eagle's Medium (MEM) and incubated for 24 h at 37ºC. The extracts from the experimental material were filtered and mixed with L929 fibroblast. Cytotoxicity was evaluated at four different times, 24, 48, 72 and 168 h. After contact, cells were incubated for 24 h and added to 100 µ of 0.01% neutral red dye. The cells were incubated for 3 h for pigment incorporation and fixed. Cells viability was determined by a spectroscopic (BioTek, Winooski, Vermont, USA) with a 492-nm wavelength λ=492 nm). There were no statistical differences between the experimental groups and the CC and C- groups. Clear, pink, blue and green self-curing acrylic resins fabricated by means of the mass manipulation technique and mechanically polished are not cytotoxic. Neither the pigment added to the self-curing acrylic resin nor the factor of time influenced the cytotoxicity of the material.

  7. In vitro cytotoxicity of self-curing acrylic resins of different colors

    Directory of Open Access Journals (Sweden)

    Luciana Borges Retamoso

    2014-08-01

    Full Text Available OBJECTIVE: The aim of this study was to assess the in vitro cytotoxicity of acrylic resins of different colors over time. METHODS: Specimens were divided into 4 groups (n = 6 according to the color of the acrylic resin (Orto Class, Clássico, Campinas, São Paulo, Brazil: Group 1: clear acrylic resin; group 2: pink acrylic resin; group 3: blue acrylic resin and group 4: green acrylic resin. All specimens were fabricated according to the mass manipulation technique and submitted to mechanical polishing protocol. The control was performed with an amalgam specimen (C+, a glass specimen (C- and cell control (CC. Specimens were immersed in Minimum Eagle's Medium (MEM and incubated for 24 h at 37o C. The extracts from the experimental material were filtered and mixed with L929 fibroblast. Cytotoxicity was evaluated at 4 different times, 24, 48, 72 and 168 h. After contact, cells were incubated for 24 h and added to 100 µ of 0.01% neutral red dye. The cells were incubated for 3 h for pigment incorporation and fixed. Cells viability was determined by a spectroscopic (BioTek, Winooski, Vermont, USA with a 492-nm wavelength λ=492 nm. RESULTS: There were no statistical differences between the experimental groups and the CC and C- groups. CONCLUSION: Clear, pink, blue and green self-curing acrylic resins fabricated by means of the mass manipulation technique and mechanically polished are not cytotoxic. Neither the pigment added to the self-curing acrylic resin nor the factor of time influenced the cytotoxicity of the material.

  8. Diffusion behavior of isobornyl acrylate into photopolymerized urethane acrylate films: influence of surface oxidation during curing.

    Science.gov (United States)

    Mougharbel, Ali; Mallégol, Jacky; Coqueret, Xavier

    2009-09-01

    The diffusion of liquid isobornyl acrylate (iBoA) into photopolymerized films of urethane acrylate was shown to be strongly dependent on curing conditions. Fourier transform infrared (FTIR) monitoring of iBoA sorption into films photopolymerized in oxygen-free conditions reveals that diffusion proceeds according to Fick's laws. The diffusion coefficient and the total amount of absorbed monomer are dependent on the degree of cure of the polymer network. When polymerized in air, the films exhibit an anomalous behavior, with a lag time increasing with the dose of applied radiation. At a comparable degree of cure, films photopolymerized in air showed a retarded diffusion with a characteristic diffusion constant close or equal to the Fickian diffusion coefficient observed with the film polymerized under nitrogen, suggesting that the retardation phenomenon was due to differences in surface interactions with liquid the monomer. X-ray photoelectron spectroscopy (XPS) measurements clearly revealed the occurrence of surface oxidation attributed to direct photolysis of urethane functions by the short wavelength component of the incident UV light. The lag time observed in samples polymerized in aerobic conditions is interpreted by the existence of H-bonded hydroperoxides forming a temporary barrier retarding monomer diffusion.

  9. Surface Structure of Acrylate Polymer Adhesives.

    Science.gov (United States)

    Roy, Sandra; Freiberg, Stephan; Leblanc, Claude; Hore, Dennis K

    2017-02-28

    Total internal reflection infrared (IR) absorption and visible-IR sum-frequency spectroscopies were used to study the role of acrylic acid in the evolution of surface structure in a poly(butyl acrylate)-based pressure-sensitive adhesive during the drying process. By monitoring these spectral responses and calculating the heterospectral correlation coefficients, we established that acrylic acid alters the nature of the molecular interactions at the surface. In the absence of acrylic acid, butyl acrylate orientation is driven by the packing of the polymer as the water evaporates. When acrylic acid is present, a rapid ordering of the copolymer takes place as a result of favorable hydrogen-bonding interactions with the surface.

  10. METHACRYLATE AND ACRYLATE ALLERGY IN DENTAL STUDENTS.

    OpenAIRE

    Maya Lyapina; Assya Krasteva; Maria Dencheva; Mariana Tzekova; Angelina Kisselova-Yaneva

    2013-01-01

    A multitude of acrylic monomers is used in dentistry, and when dental personnel, patients or students of dental medicine become sensitized, it is of great importance to identify the dental ;acrylic preparations to which the sensitized individual can be exposed. Numerous studies confirm high incidence of sensitization to (meth) acrylates in dentatal professionals, as well as in patients undergoing dental treatment and exposed to resin-based materials. Quite a few studies are available aiming t...

  11. Vinyl Acetate/butyl acrylate/acrylate Research of Ternary Soap-free Emulsion Polymerization

    Directory of Open Access Journals (Sweden)

    Xiao Li-guang

    2016-01-01

    Full Text Available Through the vinyl acetate/butyl acrylate/acrylic acrylic emulsion preparation without soap vinegar, with solid content, gel, emulsion stability and film forming properties and tensile strength as the main index to study the effect of raw materials on the properties of emulsion. Through the infrared spectrometer soap-free emulsion for microscopic analysis research. Study of the ternary soap-free vinegar acrylic emulsion with good performance.

  12. Contact dermatitis from acrylics in a histology laboratory assistant.

    Science.gov (United States)

    Molina, Luciana; Amado, Antoine; Mattei, Peter L; Taylor, James S

    2009-01-01

    The use of acrylics has expanded enormously, resulting in a vast range of products for both occupational and non-occupational purposes. Acrylics reported to cause allergic contact dermatitis in histology technicians are 2-hydroxyethyl methacrylate and 2-hydroxyethel acrylate.

  13. The Effect of Hydrogen Bonding on Radical Semi-Batch Copolymerization of Butyl Acrylate and 2-Hydroxyethyl Acrylate

    National Research Council Canada - National Science Library

    Jan E S Schier; David Cohen-Sacal; Owen R Larsen; Robin A Hutchinson

    2017-01-01

    The radical copolymerization of butyl acrylate (BA) and 2-hydroxyethyl acrylate (HEA) was investigated under batch and semi-batch operations, with a focus on the influence of hydrogen-bonding on acrylate backbiting...

  14. CLEAR test facility

    CERN Multimedia

    Ordan, Julien Marius

    2017-01-01

    A new user facility for accelerator R&D, the CERN Linear Electron Accelerator for Research (CLEAR), started operation in August 2017. CLEAR evolved from the former CLIC Test Facility 3 (CTF3) used by the Compact Linear Collider (CLIC). The new facility is able to host and test a broad range of ideas in the accelerator field.

  15. Radiopurity measurement of acrylic for DEAP-3600

    Energy Technology Data Exchange (ETDEWEB)

    Nantais, C. M.; Boulay, M. G. [Department of Physics, Engineering Physics, and Astronomy, Queen' s University, Kingston, Ontario K7L 3N6 (Canada); Cleveland, B. T. [SNOLAB, Lively, Ontario P3Y 1N2 Canada and Department of Physics, Laurentian University, Sudbury, Ontario P3E 2C6 (Canada)

    2013-08-08

    The spherical acrylic vessel that contains the liquid argon target is the most critical detector component in the DEAP-3600 dark matter experiment. Alpha decays near the inner surface of the acrylic vessel are one of the main sources of background in the detector. A fraction of the alpha energy, or the recoiling nucleus from the alpha decay, could misreconstruct in the fiducial volume and result in a false candidate dark matter event. Acrylic has low levels of inherent contamination from {sup 238}U and {sup 232}Th. Another background of particular concern is diffusion of {sup 222}Rn during manufacturing, leading to {sup 210}Pb contamination. The maximum acceptable concentrations in the DEAP-3600 acrylic vessel are ppt levels of {sup 238}U and {sup 232}Th equivalent, and 10{sup −8} ppt {sup 210}Pb. The impurities in the bulk acrylic will be measured by vaporizing a large quantity of acrylic and counting the concentrated residue with ultra-low background HPGe detectors and a low background alpha spectrometer. An overview of the acrylic assay technique is presented.

  16. Poly(meth)acrylate-based coatings.

    Science.gov (United States)

    Nollenberger, Kathrin; Albers, Jessica

    2013-12-05

    Poly(meth)acrylate coatings for pharmaceutical applications were introduced in 1955 with the launch of EUDRAGIT(®) L and EUDRAGIT(®) S, two types of anionic polymers. Since then, by introducing various monomers into their polymer chains and thus altering their properties, diverse forms with specific characteristics have become available. Today, poly(meth)acrylates function in different parts of the gastrointestinal tract and/or release the drug in a time-controlled manner. This article reviews the properties of various poly(meth)acrylates and discusses formulation issues as well as application possibilities. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Diet - clear liquid

    Science.gov (United States)

    ... things such as: Clear broth Tea Cranberry juice Jell-O Popsicles Why you may Need This Diet You ... sodas, such as ginger ale and Sprite Gelatin (Jell-O) Popsicles that do not have bits of fruit, ...

  18. Disinfection of denture base acrylic resin.

    Science.gov (United States)

    Lin, J J; Cameron, S M; Runyan, D A; Craft, D W

    1999-02-01

    During repair or adjustments of acrylic resin removable complete and partial dentures, particles of the acrylic resin from the interior of the prosthesis may expose dental personnel to microbial health hazards if the prosthesis has not been thoroughly disinfected. This study investigates the efficacy of a commercially prepared microbial disinfectant (Alcide) on the external and internal surfaces of acrylic resins. Four groups of acrylic resin were incubated in an experimental model to simulate the oral environment over time. Specimens were treated in 2 groups, disinfected and not disinfected, and then further grouped by breaking and not breaking. Analysis was performed with microbial colony counts, SEM, and statistical analyses. Viable microorganisms still remain on the internal and external surfaces of treated resins. Chlorine dioxide reduces, but does not eliminate, viable microorganisms on these dental prostheses.

  19. Resistance of acrylic vessel to gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Carneiro, Andre Cavalcanti; Menezes, Maria Angela de B.C.; Pereira, Marcio Tadeu; Rocha, Nirlando Antonio; Vilela, Jefferson Jose, E-mail: andreccarneiro@gmail.com, E-mail: menezes@cdtn.br, E-mail: mtp@cdtn.br, E-mail: nar@cdtn.br, E-mail: jjv@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Braga, Mario Roberto Martins S.S., E-mail: mariomartins@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Programa de Pos-Graduacao em Ciencias e Tecnicas Nucleares

    2013-07-01

    This paper describes the preliminary studies made in acrylic material in order to verify the effects of radiolysis in acrylic recipients in which the uranium ore standards are conditioned and check if the material is able to keep the {sup 222}Rn inside the vessel. The preliminary results after gamma irradiation of two kinds of recipients indicate no differences between the vessels irradiated and the ones no irradiated, related to color changes and tension resistance. (author)

  20. The CLEAR 2007 Evaluation

    Science.gov (United States)

    2007-01-01

    FBK-IRST), the Universitat Politécnica de Catalunya , Barcelona, Spain (UPC), the Laboratoire d’Informatique pour la mécanique et les sciences de...especially in natural, application-near scenarios such as in CLEAR, still poses some difficult questions that must be investigated. Appendix A

  1. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    Science.gov (United States)

    Sidhu, S K; Shaw, S

    1999-05-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in both the conducting gel of disposable blue diathermy pads, and artificial sculptured acrylic nails. We advocate careful history taking prior to surgery to avoid unnecessary exposure to acrylates in patients already sensitized.

  2. In vivo testing of the protection of gloves against acrylates in dentin-bonding systems on patients with known contact allergy to acrylates.

    Science.gov (United States)

    Andersson, T; Bruze, M; Björkner, B

    1999-11-01

    Occupational contact allergies to dental acrylates are increasing. Commonly used gloves protect poorly against acrylates. The protective efficacy in vivo of other, newer glove materials is not fully known. In this study, an open chamber system was used for testing the protection in vivo of 6 different gloves (1 vinyl glove, 2 latex gloves, 2 nitrile gloves and the 4H glove) against a commonly used dental adhesive, Scotchbond 1, containing 2-hydroxyethyl methacrylate (2-HEMA) and triethylene glycol dimethacrylate (TREGDMA). 8 patients with known contact allergy to 2-HEMA participated. Provocation with 50 microl of the adhesive for 7.5, 15 and 30 min was performed for each glove. The test demonstrated clear differences in the protective efficacy between the gloves. The 4H glove gave by far the best protection, followed by one of the nitrile gloves. One of the latex gloves and the vinyl glove gave a very poor protection against the adhesive. A dose-response relationship was observed between different application times of the acrylate product. The test model promises to be a useful clinical complement to in vitro methods in individual preventive measures against contact sensitization to acrylates.

  3. The effect of nail polish and acrylic nails on pulse oximetry reading using the Lifebox oximeter in Nigeria.

    Science.gov (United States)

    Desalu, I; Diakparomre, O I; Salami, A O; Abiola, A O

    2013-12-01

    AIMS AND OBJECTIVES - Pulse oximetry is mandatory during anaesthesia, sedation and transfer of critically ill patients. The effect of nail polish and acrylic nails on the accuracy of saturation reading is inconsistent. The Lifebox pulse oximeter is reliable and recommended for low and middle income countries. We investigated its accuracy in the presence of 4 nail colours and acrylic nails SUBJECTS AND METHODS Fifty non-smoking volunteers had their fingers numbered from right to left (little finger of right hand =1 and little finger of left hand =10). Alternate fingers were nails painted with clear, red, brown and black nail polish and the 5th finger had acrylic nail applied. The corresponding finger on the other hand acted as control. The oxygen saturation was determined using the Lifebox pulse oximeter. Results All fingers (100%) with clear nail polish, red nail polish and acrylic nails recorded a saturation value. Each of the mean saturation value for clear nail polish, red nail polish and acrylic nails was not significantly different from the control mean (p= 0.378, 0.427 and 0.921). Only 12% and 64% of nails polished black and brown respectively recorded a saturation value. The mean SpO- for black and brown polish were significantly different from their control mean (ppolish resulted in a significant decrease in SpO with the Lifebox oximeter. Dark coloured nail polish should be removed prior to SpO2 determination to ensure that accurate readings can be obtained.

  4. Occupational methacrylate and acrylate allergy from glues.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Alanko, Kristiina; Kuuliala, Outi; Jolanki, Riitta

    2008-06-01

    Glues and sealants are important causes of methacrylate and acrylate allergy. This study aimed to analyse patterns of allergic patch test reactions to acrylic monomers in relation to exposure in patients sensitized from glues. We screened the patch test files at the Finnish Institute of Occupational Health from 1994 to 2006 for allergic reactions in the 'Methacrylate series' and analysed the clinical records of sensitized patients. Only patients who had handled acrylic glues at work were included. 10 patients had allergic reactions to acrylic monomers and had been sensitized from glues at work. 9 of them had used anaerobic sealants, 3 cyanoacrylate-based instant adhesives, and 1 patient a bi-component instant adhesive. All the patients reacted to 2-hydroxyethyl methacrylate (2-HEMA) and ethyleneglycol dimethacrylate (EGDMA); reactions to 2-hydroxypropyl methacrylate, triethyleneglycol dimethacrylate, and tetrahydrofurfuryl methacrylate were also common. The first 4 methacrylates were found in the glues used by the patients. Ethyl cyanoacrylate (ECA) gave no reactions, but 1 patient reacted weakly to her own ECA-based glue. 2-HEMA and EGDMA are good screeners for contact allergy to anaerobic sealants and also detected a single case deriving from bi-component acrylic glue.

  5. Methacrylate and acrylate allergy in dental personnel.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Alanko, Kristiina; Kuuliala, Outi; Jolanki, Riitta

    2007-11-01

    Methacrylates are important allergens in dentistry. The study aimed to analyse patch test reactivity to 36 acrylic monomers in dental personnel in relation to exposure. We reviewed the test files at the Finnish Institute of Occupational Health from 1994 to 2006 for allergic reactions to acrylic monomers in dental personnel and analysed the clinical records of the sensitized patients. 32 patients had allergic reactions to acrylic monomers: 15 dental nurses, 9 dentists, and 8 dental technicians. The dentists and dental nurses were most commonly exposed to 2-hydroxyethyl methacrylate (2-HEMA), triethyleneglycol dimethacrylate (TREGDMA), and 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy) phenyl]propane (bis-GMA). 8 dentists and 12 dental nurses were allergic to 2-HEMA. The remaining dentist was positive to bis-GMA and other epoxy acrylates. The remaining 3 dental nurses reacted to diethyleneglycol diacrylate (DEGDA) or triethyleneglycol diacrylate (TREGDA), but not to monofunctional and multifunctional methacrylates. Our dental technicians were mainly exposed and sensitized to methyl methacrylate (MMA) and ethyleneglycol dimethacrylate (EGDMA). 1 technician reacted only to 2-HEMA, and another to ethyl methacrylate (EMA) and ethyl acrylate (EA). 2-HEMA was the most important allergen in dentists and dental nurses, and MMA and EGDMA in dental technicians. Reactions to bis-GMA, DEGDA, TREGDA, EMA and EA were relevant in some patients.

  6. All-acrylic superelastomers: facile synthesis and exceptional mechanical behavior

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Wei [Department of Chemistry; University of Tennessee; Knoxville; USA; Goodwin, Andrew [Department of Chemistry; University of Tennessee; Knoxville; USA; Wang, Yangyang [Center for Nanophase Materials Sciences; Oak Ridge National Laboratory; Oak Ridge; USA; Yin, Panchao [Chemical and Engineering Materials Division; Oak Ridge National Laboratory; Oak Ridge; USA; Wang, Weiyu [Center for Nanophase Materials Sciences; Oak Ridge National Laboratory; Oak Ridge; USA; Zhu, Jiahua [Center for Nanophase Materials Sciences; Oak Ridge National Laboratory; Oak Ridge; USA; Wu, Ting [Department of Materials Science and Engineering; University of Tennessee; Knoxville; USA; Lu, Xinyi [Department of Chemistry; University of Tennessee; Knoxville; USA; Hu, Bin [Department of Materials Science and Engineering; University of Tennessee; Knoxville; USA; Hong, Kunlun [Center for Nanophase Materials Sciences; Oak Ridge National Laboratory; Oak Ridge; USA; Kang, Nam-Goo [Department of Chemistry; University of Tennessee; Knoxville; USA; Mays, Jimmy [Department of Chemistry; University of Tennessee; Knoxville; USA

    2018-01-01

    All-acrylic multigraft copolymers made by a facile synthesis procedure exhibit elongation at break >1700% and strain recovery behavior far exceeding those of commercial acrylic and styrenic triblock copolymers.

  7. High acrylate concentrations in the mucus of Phaeocystis globosa colonies

    NARCIS (Netherlands)

    Noordkamp, D.J B; Schotten, M; Gieskes, W.W C; Forney, L.J; Gottschal, J.C; van Rijssel, M

    1998-01-01

    Acrylate produced from dimethylsulphoniopropionate (DMSP) by Phaeocystis has been claimed to inhibit bacterial growth. However, the concentrations of acrylate measured in seawater during Phaeocystis blooms are not high enough to expect inhibition of bacterial growth. In this study, the total

  8. In-depth disinfection of acrylic resins.

    Science.gov (United States)

    Chau, V B; Saunders, T R; Pimsler, M; Elfring, D R

    1995-09-01

    This study demonstrated that bacteria penetrate three kinds of dental acrylic resin after a short time period. Samples of acrylic resin were contaminated with a variety of bacteria and were then placed in three different disinfecting solutions as directed by the manufacturers. After the specific dilution and immersion time, cultures were made from the resin samples. The only effective disinfectant was a 0.525% solution of sodium hypochlorite at a 10-minute immersion. It disinfected not only the surfaces but also the bacteria that penetrated the surfaces to a depth of 3 mm.

  9. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    OpenAIRE

    Sidhu, S K; Shaw, S.

    1999-01-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in...

  10. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane acrylate...

  11. Allergic contact dermatitis due to an epoxy acrylate.

    Science.gov (United States)

    Nethercott, J R

    1981-06-01

    A printer developed allergic contact dermatitis due to epoxy acrylate resin. Incomplete cross-reactivity between four epoxy acrylate resins and a lack of cross-reactivity to epoxy resin was demonstrated. The epoxy acrylate resin has been shown to be a potent cutaneous sensitizer for the guinea-pig.

  12. 40 CFR 721.4794 - Polypiperidinol-acrylate methacrylate.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polypiperidinol-acrylate methacrylate... Substances § 721.4794 Polypiperidinol-acrylate methacrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polypiperidinol-acrylate...

  13. 78 FR 6213 - Styrene-2-Ethylhexyl Acrylate Copolymer; Tolerance Exemption

    Science.gov (United States)

    2013-01-30

    ... AGENCY 40 CFR Part 180 Styrene-2-Ethylhexyl Acrylate Copolymer; Tolerance Exemption AGENCY: Environmental...; also known as styrene-2-ethylhexyl acrylate copolymer when used as an inert ingredient in a pesticide...-risk polymers are described in 40 CFR 723.250(d). Styrene-2-ethylhexyl acrylate copolymer conforms to...

  14. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Halogenated benzyl ester acrylate... Specific Chemical Substances § 721.329 Halogenated benzyl ester acrylate (generic). (a) Chemical substance... halogenated benzyl ester acrylate (PMN P-90-1527) is subject to reporting under this section for the...

  15. 40 CFR 721.10081 - Aromatic urethane acrylate oligomer (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aromatic urethane acrylate oligomer... Specific Chemical Substances § 721.10081 Aromatic urethane acrylate oligomer (generic). (a) Chemical... as aromatic urethane acrylate oligomer (PMN P-06-26) is subject to reporting under this section for...

  16. 40 CFR 721.5325 - Nickel acrylate complex.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting under...

  17. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-ethyl acrylate copolymers. 177.1320... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1320 Ethylene-ethyl acrylate copolymers. Ethylene-ethyl acrylate copolymers may be safely used to produce packaging materials, containers...

  18. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be safely...

  19. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573.120 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin...

  20. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylamide-acrylic acid resins. 176.110 Section 176... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in producing...

  1. 21 CFR 173.5 - Acrylate-acrylamide resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate-acrylamide resins. 173.5 Section 173.5... CONSUMPTION Polymer Substances and Polymer Adjuvants for Food Treatment § 173.5 Acrylate-acrylamide resins. Acrylate-acrylamide resins may be safely used in food under the following prescribed conditions: (a) The...

  2. Amylase catalyzed synthesis of glycosyl acrylates and their polymerization

    NARCIS (Netherlands)

    Kloosterman, Wouter M.J.; Jovanovic, Danijela; Brouwer, Sander; Loos, Katja

    2014-01-01

    The enzymatic synthesis of novel (di)saccharide acrylates from starch and 2-hydroxyethyl acrylate, 2-hydroxyethyl methacrylate and 4-hydroxybutyl acrylate (2-HEA, 2-HEMA and 4-HBA) catalyzed by various commercially available amylase preparations is demonstrated. Both liquefaction and

  3. Thermal bulk polymerization of cholesteryl acrylate

    NARCIS (Netherlands)

    de Visser, A.C.; de Groot, K.; Feijen, Jan; Bantjes, A.

    1971-01-01

    The thermal bulk polymerization of cholesteryl acrylate was carried out in the solid phase, the mesomorphic phase, and the liquid phase to study the effect of monomer ordering on polymerization rate and polymer properties. The rate increased with decreasing ordering (or enhanced mobility) of the

  4. Thermal Polymerization of N-Butyl Acrylate

    Science.gov (United States)

    Ingham, J. D.

    1982-01-01

    Simple new polymerization method enables production of n-butyl acrylate polymer of desired high molecular weight, without disadvantages that usually attend more conventional methods. Process, which is hybrid of thermal, solution, and emulsion polymerization methods, involves controlled thermal polymerization of monomer at moderate temperatures without use of catalysts or additives.

  5. 40 CFR 721.405 - Polyether acrylate.

    Science.gov (United States)

    2010-07-01

    ... 721.405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL...) The chemical substance identified generically as a polyether acrylate (PMN P-95-666) is subject to... this section except as modified by this paragraph. (1) Recordkeeping. Recordkeeping requirements as...

  6. Development and Evaluation of Ketoprofen Acrylic Transdermal ...

    African Journals Online (AJOL)

    Purpose: To fabricate ketoprofen transdermal patches (KTPs) using an acrylic pressure-sensitive adhesive (PSA) polymer. Methods: KTPs were prepared using solvent casting method. The influence of the amount of PSA, drug content, and terpenes as penetration enhancers on the characteristics of the patch, namely, ...

  7. Influence of composition on the morphology of polyurethane/acrylic latex particles and adhesive films

    OpenAIRE

    Degrandi-Contraires, Elise; Udagama, Ravindra; Mckenna, Timothy; Bourgeat-Lami, Elodie; Plummer, Christopher J.G.; Creton, Costantino

    2014-01-01

    International audience; Polyurethane (PU)/acrylic hybrid particles with different PU contents were synthesized by miniemulsion polymerization and subsequently dried to give solid adhesive films. The morphologies of the particles and the morphologies and mechanical properties of the resulting films were investigated by Transmission electron microscopy combined with selective staining of the PU and by uniaxial tension tests. Morphological investigations showed a clear change in the particle mor...

  8. METHACRYLATE AND ACRYLATE ALLERGY IN DENTAL STUDENTS.

    Directory of Open Access Journals (Sweden)

    Maya Lyapina

    2013-09-01

    Full Text Available A multitude of acrylic monomers is used in dentistry, and when dental personnel, patients or students of dental medicine become sensitized, it is of great importance to identify the dental ;acrylic preparations to which the sensitized individual can be exposed. Numerous studies confirm high incidence of sensitization to (meth acrylates in dentatal professionals, as well as in patients undergoing dental treatment and exposed to resin-based materials. Quite a few studies are available aiming to evaluate the incidence of sensitization in students of dental medicineThe purpose of the study is to evaluate the incidence of contact sensitization to some (meth acrylates in students of dental medicine at the time of their education, in dental professionals (dentists, nurses and attendants and in patients, the manifestation of co-reactivity.A total of 139 participants were included in the study, divided into four groups: occupationally exposed to (methacrylates and acrylic monomers dental professionals, 3-4 year-of-education students of dental medicine, 6th year–of-education students of dental medicine and patients with suspected or established sensitization to acrylates, without occupational exposure. All of them were patch-tested with methyl methacrylate (MMA, triethyleneglycol dimethacrylate (TREGDMA, ethyleneglycol dimethacrylate (EGDMA, 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy phenyl]propane (bis-GMA, 2-hydroxyethyl methacrylate (2-HEMA, and tetrahidrofurfuril metacrylate. The overall sensitization rates to methacrylates in the studied population are comparative high – from 25.9% for MMA to 31.7% for TREGDMA. Significantly higher incidence of sensitization in the group of 3-4 course students compared to the one in the group of dental professionals for MMA and TREGDMA was observed. Highest was the incidence of sensitization to ethyleneglycol dimethacrylate, BIS-GMA, 2-HEMA and tetrahydrofurfuryl methacrylate in the group of patients, with

  9. Shear bond strength of acrylic teeth to acrylic denture base after different surface conditioning methods.

    Science.gov (United States)

    Madhav, Gajula Venu; Raj, Soundar; Yadav, Naveen; Mudgal, Ishitha; Mehta, Nidhi; Tatwadiya, Riddhi

    2013-09-01

    Acrylic resin ruled the dental profession for 60 years, and this success is attributed to its aesthetics, handling properties, physical and biological compatibility, its stability in oral environment and its cost effectiveness. The objective of this study is to evaluate and compare the bond strength of acrylic resin teeth treated with various conditioning materials like monomer and silane coupling agent. METHDOLOGY: A study was carried out in which 96 samples were grouped into 3 groups with a sample size of 32 each (16 premolars, 16 molars). They were conditioned with different conditioning materials i,e monomer and silane coupling agent. Monomer, Silane coupling agent are coated on the ridge lap area before thermocycling and cured according to the manufacturer recommendations. The samples are retained from the fask; trimmed and polished. The samples are then subjected to shear bond strength using the Insteron Universal Testing Machine. In the present study it was found that application of monomer increased the bond strength between acrylic teeth and denture base, when compared to the conventionally processed samples. However it was found that application of silane coupling agent further increased the shear bond strength between acrylic teeth and denture base. Interprations and Within the confnes of this study it is found that there was a signifcant improvement in the bond strength between the acrylic teeth and denture base when silane coupling agent and monomer were used as surface conditioning material. The order of shear strength of samples is control > monomer > silane coupling agent.

  10. Allergic contact dermatitis from dental composite resins due to aromatic epoxy acrylates and aliphatic acrylates.

    Science.gov (United States)

    Kanerva, L; Estlander, T; Jolanki, R

    1989-03-01

    7 patients were occupationally sensitized to dental composite resin products (DCR): 6 dental nurses and 1 dentist. All had a positive patch test to their DCR. 2 independent types of allergy were seen; (a) aromatic epoxy acrylate, and/or (b) aliphatic acrylates. 4 out of 5 patients reacted to BIS-GMA, the most widely used aromatic epoxy acrylate in DCR, but not the dentist. She and 2 dental nurses were allergic to aliphatic acrylates, including triethylene glycol dimethacrylate (TREGDMA) and triethylene diglycol diacrylate (TREGDA). 4 patients were allergic to epoxy resin (ER) (containing mainly MW 340), possibly an impurity in some DCR. 2 patients were also allergic to methyl methacrylate (MMA): the dentist, had been exposed to MMA, but the nurse's exposure was uncertain. 1 patient was also allergic to rubber gloves, 2 to rubber chemicals but not their gloves, and 5 to disinfectants used. diagnosis was delayed as long as 13 years in spite of previous patch testing. Dermatologists need to use the patients' own DCR and the (meth)acrylate series for patch testing. No dental nurses could continue their occupation, but the dentist could occasionally handle DCR if wearing PVC gloves. Dental personnel need to know about the risks of DCR, and use no-touch techniques and protective gloves.

  11. Isobornyl acrylate: an impurity in alkyl glucosides.

    Science.gov (United States)

    Foti, Caterina; Romita, Paolo; Rigano, Luigi; Zimerson, Erik; Sicilia, Mattia; Ballini, Andrea; Ghizzoni, Oscar; Antelmi, Annarita; Angelini, Gianni; Bonamonte, Domenico; Bruze, Magnus

    2016-01-01

    Alkyl glucosides and alkyl poly-glucosides are widely used as wetting agents, surfactants and emulsifiers in several industrial and cosmetic products. They are known as well-tolerated and are usually added to the primary surfactants in order to reduce the irritating potential of the main foaming agents. Recently, some authors suggested that allergic contact dermatitis to alkyl glucosides might be more frequent than suspected. On the other hand, the chemical structures of glucosides do not show potentially allergenic chemical groups or strongly polarized structures. The aim of our study is to investigate alkyl glucosides carrying out a detailed chemical analysis on samples of raw materials to identify potentially allergenic impurities or by-products contained in commercial samples of alkyl glucosides. We chemically analyzed samples of cocoyl glucoside, decyl glucoside and lauryl glucoside by three different analytical methods, in order to identify any undesired or polluting substances. In each of the three samples, we detected the presence of isobornyl acrylate. Its approximate content in the tested samples is 500 ng/g of the product. Isobornyl acrylate is not used in the synthesis of alkyl glucosides, but as a plasticizer in many plastic materials. It can be easily released to materials flowing over these surfaces when they have high extraction power, as glucosides. Isobornyl acrylate may play a role as hidden allergen, in the form of an impurity collected during the industrial process, explaining some cases of allergic reaction to alkyl glucosides.

  12. Acrylated Chitosan Nanoparticles with Enhanced Mucoadhesion

    Directory of Open Access Journals (Sweden)

    Shaked Eliyahu

    2018-01-01

    Full Text Available The aim of this study was to investigate the effect of acrylate modification on the mucoadhesion of chitosan at the nanoscale. Nanoparticles were fabricated from acrylated chitosan (ACS via ionic gelation with tripolyphosphate and were characterized in terms of size, zeta potential, stability, and nanoparticle yield. Chitosan (CS nanoparticles, serving as a control, were fabricated using the same procedure. The mucoadhesion of the nanoparticles was evaluated using the flow-through method after different incubation periods. The retention percentages of ACS nanoparticles were found to be significantly higher than those of CS nanoparticles, for all studied time intervals. An additional indication for the increased mucoadhesion of ACS nanoparticles was the increase in particle size obtained from the mucin particle method, in which mucin and nanoparticles are mixed at different ratios. NMR data verified the presence of free acrylate groups on the ACS nanoparticles. Thus, the improved mucoadhesion could be due to a Michael-type addition reaction between the nanoparticles and thiol groups present in mucin glycoprotein, in addition to entanglements and hydrogen bonding. Overall, ACS nanoparticles exhibit enhanced mucoadhesion properties as compared to CS nanoparticles and could be used as vehicles for drug delivery systems.

  13. Contact allergy to acrylates/methacrylates in the acrylate and nail acrylics series in southern Sweden: simultaneous positive patch test reaction patterns and possible screening allergens.

    Science.gov (United States)

    Teik-Jin Goon, Anthony; Bruze, Magnus; Zimerson, Erik; Goh, Chee-Leok; Isaksson, Marléne

    2007-07-01

    In a recent study we showed that all our dental personnel/patients were detected with 2-hydroxyethyl methacrylate (2-HEMA) and 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy)phenyl]propane (bis-GMA). We studied 90 patients tested to the acrylate and nail acrylics series at our department over a 10 year period to see whether screening allergens could be found. Patch testing with an acrylate and nail acrylics series was performed. Among the 10 acrylate/methacrylate-allergic occupational dermatitis patients tested to the acrylate series, the most common allergens were triethyleneglycol diacrylate (TREGDA, 8), diethyleneglycol diacrylate (5), and 1,4-butanediol diacrylate (BUDA, 5). All 10 of these patients would have been picked up by a short screening series combining TREGDA, 2-hydroxypropyl methacrylate (2-HPMA), and BUDA or 1,6-hexanediol diacrylate (HDDA). Among the 14 acrylate/methacrylate-allergic nail patients, the most common allergens were ethylene glycol dimethacrylate (EGDMA, 11), 2-HEMA, (9), and triethyleneglycol dimethacrylate (9). Screening for 3 allergens i.e. 2-HEMA plus EGDMA plus TREGDA, would have detected all 14 nail patients. A short screening series combining 2-HEMA, EGDMA, TREGDA, 2-HPMA, bis-GMA, and BUDA or HDDA would have picked up all our past study patients (dental, industrial, and nail) with suspected allergy to acrylate/methacrylate allergens.

  14. Waterborne hyperbranched alkyd-acrylic resin obtained by miniemulsion polymerization

    Directory of Open Access Journals (Sweden)

    Edwin Murillo

    Full Text Available Abstract Four waterborne hyperbranched alkyd-acrylic resins (HBRAA were synthesized by miniemulsion polymerization from a hyperbranched alkyd resin (HBR, methyl methacrylate (MMA, butyl acrylate (BA and acrylic acid (AA, by using benzoyl peroxide (BPO and ammonium persulfate (AP as initiators. The reaction between HBR and acrylic monomers was evidenced by differential scanning calorimetric (DSC, nuclear magnetic resonance (NMR and gel permeation chromatography (GPC. The conversion percentage, glass transition temperature (Tg, content of acrylic polymer (determined by soxhlet extraction and molecular weight increased with the content of acrylic monomers used in the synthesis. The main structure formed during the synthesis was the HBRAA. The analysis by dynamic light scattering (DLS showed that the particle size distribution of HBRAA2, HBRAA3 and HBRAA4 resins were mainly monomodal. The film properties (gloss, flexibility, adhesion and drying time of the HBRAA were good.

  15. [Sensitization to acrylates caused by artificial acrylic nails: review of 15 cases].

    Science.gov (United States)

    Roche, E; de la Cuadra, J; Alegre, V

    2008-12-01

    Allergic contact dermatitis due to acrylates present in the workplace is a disease frequently reported among dentists, printers, and fiberglass workers. Recently, the number of cases of contact allergic dermatitis among beauticians specialized in sculpting artificial nails has increased. Our objective was to study the clinical characteristics and allergens implicated in allergic contact dermatitis due to acrylates in beauticians and users of sculpted nails. This was an observational, retrospective study of patients diagnosed with allergic contact dermatitis due to acrylates used in sculpting artificial nails over the last 26 years in the Hospital General Universitario, Valencia, Spain. In total, 15 patients were diagnosed: 14 beauticians and 1 client. Most cases were diagnosed in the past 2 years. All were women, their mean age was 32.2 years, and 26.7 % had a personal or family history of atopy. The sensitization time varied between 1 month and 15 years. The most frequently affected areas were the fleshy parts of the fingers and hands. Three patients - 2 beauticians and 1 client - presented allergic asthma due to acrylates. All patients underwent patch testing with a standard battery of allergens and a battery of acrylates. The most frequent allergens were ethylene glycol dimethacrylate (13/15, 86.7 %), hydroxyethyl methacrylate (13/15, 86.7 %), triethylene glycol dimethacrylate (7/15, 46.7 %), 2-hydroxypropyl methacrylate (5/15, 33.3 %), and methyl methacrylate (5/15, 33.3 %). Acrylate monomers used for sculpting artificial nails are important sensitizers for contact and occupational dermatitis. The most important consideration is primary and secondary prevention.

  16. Severe Onychodystrophy due to Allergic Contact Dermatitis from Acrylic Nails.

    Science.gov (United States)

    Mattos Simoes Mendonca, Marcela; LaSenna, Charlotte; Tosti, Antonella

    2015-09-01

    Acrylic nails, including sculptured nails and the new ultraviolet-curable gel polish lacquers, have been associated with allergic contact dermatitis (ACD). We report 2 cases of ACD to acrylic nails with severe onychodystrophy and psoriasiform changes including onycholysis and subungual hyperkeratosis. In both cases, the patients did not realize the association between the use of acrylate-based manicures and nail changes. One patient had been previously misdiagnosed and treated unsuccessfully for nail psoriasis. The informed clinician should elicit a history of acrylic manicure in patients with these nail changes, especially in cases of suspected nail psoriasis refractory to treatment. Patch testing is a useful tool in confirming diagnosis.

  17. Occupational allergic contact dermatitis due to acrylates in Lodz.

    Science.gov (United States)

    Kiec-Swierczynska, M K

    1996-06-01

    Among 1619 patients suspected of occupational contact dermatitis examined during the years 1990-1994, sensitivity to acrylates was diagnosed in 9 persons (4 dental technicians, 4 dentists, 1 textile printer). Ethyleneglycol dimethacrylate (5 positive patch tests), methyl methacrylate (4), 2-hydroxyethyl methacrylate (4) and triethyleneglycol dimethacrylate (4) were the most common sensitizers. Comparison of patch test results in dental technicians and dentists indicated that dentists were sensitive to a greater number of (meth)acrylate (acrylate and methacrylate) allergens and also to certain other allergens (metals and rubber additives). Dental technicians were sensitive almost exclusively to methacrylates, while the textile printer only to acrylates.

  18. Fibronectin fixation on poly(ethyl acrylate)-based copolymers.

    Science.gov (United States)

    Briz, N; Antolinos-Turpin, C M; Alió, J; Garagorri, N; Ribelles, J L Gómez; Gómez-Tejedor, J A

    2013-08-01

    The aim of this paper is to quantify the adhered fibronectin (FN; by adsorption and/or grafting) and the exposure of its cell adhesive motifs (RGD and FNIII7-10) on poly(ethyl acrylate) (PEA) copolymers whose chemical composition has been designed to increase wettability and to introduce acid functional groups. FN was adsorbed to PEA, poly(ethyl acrylate-co-hydroxyethyl acrylate), poly(ethyl acrylate-co-acrylic acid), and poly(ethyl acrylate-co-methacrylic acid) copolymers, and covalently cross-linked to poly(ethyl acrylate-co-acrylic acid) and poly(ethyl acrylate-co-methacrylic acid) copolymers. Amount of adhered FN and exhibition of RGD and FNIII7- 10 fragments involved in cell adhesion were quantified with enzyme-linked immunosorbent assay tests. Even copolymers with a lower content of the hydrophilic component showed a decrease in water contact angle. In addition, FN was successfully fixed on all surfaces, especially on the hydrophobic surfaces. However, it was demonstrated that exposure of its cell adhesion sequences, which is the key factor in cell adhesion and proliferation, was higher for hydrophilic surfaces. Copyright © 2013 Wiley Periodicals, Inc.

  19. Synthesis of Poly(styrene-acrylates-acrylic acid Microspheres and Their Chemical Composition towards Colloidal Crystal Films

    Directory of Open Access Journals (Sweden)

    Luis A. Ríos-Osuna

    2016-01-01

    Full Text Available In this paper, polystyrene colloidal microspheres have been prepared using hexyl acrylate (HA, ethylhexyl acrylate (EHA, isooctyl acrylate (IOA, butyl acrylate (BA, or isobutyl acrylate (IBA as comonomers. Microspheres with diameters from 212 to 332 nm and with a polystyrene content of 65–78% were prepared. The particles prepared in this work do not present the typical core-shell structure; as a consequence, DSC analysis showed that the microspheres exhibited only one Tg. TEM images show that the particles with comonomer content below ~30% were spherical and regular. Microspheres containing comonomer between 21 to 25% produced the less brittle films showing very iridescent colors. The films prepared from microspheres containing hexyl, ethylhexyl, and isooctyl acrylate as comonomers are firmly attached to the substrate due to their adhesive properties. The large decrease of the fragility observed in these films makes them much more attractive materials in sensing applications.

  20. Kinetics and products of gas-phase reactions of ozone with methyl methacrylate, methyl acrylate, and ethyl acrylate.

    Science.gov (United States)

    Bernard, F; Eyglunent, G; Daële, V; Mellouki, A

    2010-08-19

    The kinetics and products of the gas-phase reactions of ozone with methyl methacrylate, methyl acrylate, and ethyl acrylate have been investigated at 760 Torr total pressure of air and 294 +/- 2 K. The rate coefficients obtained (in cm(3) molecule(-1) s(-1) units) were as follows: k(methyl methacrylate) = (6.7 +/- 0.9) x 10(-18), k(methyl acrylate) = (0.95 +/- 0.07) x 10(-18), and k(ethyl acrylate) = (1.3 +/- 0.1) x 10(-18). In addition to formaldehyde being observed as a product of the three reactions, the other major reaction products were methyl pyruvate from reaction of ozone with methyl methacrylate, methyl glyoxylate from reaction of ozone with methyl acrylate, and ethyl glyoxylate from reaction of ozone with ethyl acrylate. Possible reaction mechanisms leading to the observed products are presented and discussed.

  1. Optical clearing of articular cartilage: a comparison of clearing agents

    Science.gov (United States)

    Bykov, Alexander; Hautala, Tapio; Kinnunen, Matti; Popov, Alexey; Karhula, Sakari; Saarakkala, Simo; Nieminen, Miika T.; Tuchin, Valery

    2015-07-01

    Optical clearing technique was applied to the problem of OCT imaging of articular cartilage and subchondral bone. We show that optical clearing significantly enhances visualization of articular cartilage and cartilage-bone interface. The effect of different clearing agents was analyzed. For the clearing, iohexol solution and propylene glycol (PG) were used. Clearing was performed in vitro at room temperature by immersion method. Cylindrical osteochondral samples (d=4.8mm) were drilled from bovine lateral femur and stored in phosphate-buffered saline at -20°C until clearing. Monitoring of clearing process was performed using high-speed spectral-domain OCT system providing axial resolution of 5.8μm at 930nm. Total duration of experiment was 90-100min to ensure saturation of clearing. We have shown that iohexol solution and PG are capable to optically clear articular cartilage enabling reliable characterization of cartilagebone interface with OCT. Being a low osmolarity agent, iohexol provides minimal changes to the thickness of cartilage sample. Clearing saturation time for the cartilage sample with the thickness of 0.9 mm measured with OCT is of 50 min. However, less than 15 min is enough to reliably detect the rear cartilage boundary. Alternatively, PG significantly (60%) reduces the cartilage thickness enabling better visualization of subchondral bone. It was observed that PG has higher clearing rate. The clearing saturation time is of 30 min, however less than 5 min is enough to detect cartilage-bone interface. We conclude that iohexol solution is superior for OCT imaging of cartilage and cartilage-bone interface, while PG suits better for subhondral bone visualization.

  2. Comparison between an Acrylic Splint Herbst and an Acrylic Splint Miniscrew-Herbst for Mandibular Incisors Proclination Control

    OpenAIRE

    Manni, Antonio; Pasini, Marco; Mazzotta, Laura; Mutinelli, Sabrina; Nuzzo, Claudio; Grassi, Felice Roberto; Cozzani, Mauro

    2014-01-01

    Aim. The aim of this study is to compare dental and skeletal effects produced by an acrylic splint Herbst with and without skeletal anchorage for correction of dental class II malocclusion. Methods. The test group was formed by 14 patients that were treated with an acrylic splint miniscrew-Herbst; miniscrews were placed between mandibular second premolars and first molars; controls also consisted of 14 subjects that were treated with an acrylic splint Herbst and no miniscrews. Cephalometric m...

  3. Clear cell melanoma: a cutaneous clear cell malignancy.

    Science.gov (United States)

    Pletneva, Maria A; Andea, Aleodor; Palanisamy, Nallasivam; Betz, Bryan L; Carskadon, Shannon; Wang, Min; Patel, Rajiv M; Fullen, Douglas R; Harms, Paul W

    2014-10-01

    Clear cell melanoma is a rare clear cell malignancy. Accurate diagnosis of clear cell melanoma requires integration of immunohistochemical and morphologic findings, with molecular studies to rule out clear cell sarcoma. The differential diagnosis includes melanoma, carcinoma, perivascular epithelioid cell tumor, and epidermotropic clear cell sarcoma. We use a case of a lesion on the helix of an 86-year-old man as an example. Histologic examination revealed an ulcerated clear cell malignant tumor. Tumor cell cytoplasm contained periodic acid-Schiff-positive, diastase-sensitive glycogen. Tumor cells showed positive labeling for S100, HMB-45, and Melan-A, and negative labeling for cytokeratins, p63, and smooth muscle actin. Molecular studies demonstrated BRAF V600E mutation, copy gains at the 6p25 (RREB1) and 11q13 (CCND1) loci, and absence of EWSR1-ATF1 fusion. These findings supported a diagnosis of clear cell melanoma. The rare pure clear cell morphology occurs due to accumulation of intracytoplasmic glycogen. We review the differential diagnosis of clear cell melanoma and describe the utility of immunohistochemical and molecular studies in confirming this diagnosis.

  4. Mass attenuation coefficients of clear-Pb for photons from 125I, 103Pd, 99mTc, 192Ir, 137Cs and 60Co.

    Science.gov (United States)

    Rivard, M J; Waid, D S; Wierzbicki, J G

    1999-11-01

    The mass attenuation coefficients, mu/rho, for Clear-Pb for photon energies ranging from 10 keV to 10 MeV were determined using Monte Carlo methods and simple equations used to manipulate elemental mass attenuation coefficients. It was determined that the effectiveness of Clear-Pb as a radiation shielding material was greater than plain acrylic for all photon energies, especially those less than 150 keV, and for deep penetration problems where the differences in mu/rho between Clear-Pb and acrylic became more significant. Finally, the usefulness of Clear-Pb as a shielding material when compared with acrylic was determined for the following commonly used radionuclides: 125I, 103Pd, 99mTc, 192Ir, 137Cs, and 60Co.

  5. [Synthesis and characterization of dihydroeugenol acrylate].

    Science.gov (United States)

    Liu, Xiao-Huan; Wang, Chun-Peng; Wang, Ji-Fu; Xu, Yu-Zhi; Chu, Fu-Xiang

    2014-04-01

    Dihydroeugenol acrylate was synthesized by the reaction of acryloyl chloride (AC) with lignin mode compound dihydroeugenol (DH) in the presence of TEA and characterized by using FTIR, GC/MS, 1H-NMR and GPC. FTIR spectra showed that, after the esterification with acryloyl chloride, the intensity of stretching vibration peak of O-H (centered at 3 495 cm(-1)) of DH was disappeared. At the same time, a new peak appeared at 1 762 cm(-1) which was assigned to ester group. Additionally, the appearance of 1 631 and 981 cm(-1) were attributed to the carbon - carbon double bond confirmed the success in the synthesis of DH-AC. 1H-NMR spectra showed that, after the esterification with acryloyl chloride, the proton signal of O-H at 5.5 ppm was disappeared. Meanwhile, the appearance of three new proton signals at 6.0 ppm, 6.4 and 6.7 ppm, attributed to the vinylic protons, indicated that acryloyl chloride was successfully grafted onto DH. The results further confirmed the structures of the DH-AC. GC-MS results showed the DH-AC had a high purity of 98.63%. GPC results showed that dihydroeugenol acrylate could polymerize in the 1,4-dioxane using a thermal initiator of AIBN (2.0 Wt% of total monomers). The weight average molecular mass (Mw) of the homopolymer is 37 400 g x mol(-1), and the number average molecular mass is 23 400 g x mol(-1)' with a polydispersity index Mw/Mn of 1.60, indicating that the dihydroeugenol acrylate has high polymerization activity. This strategy provides a novel approach for extending the comprehensive utilization of lignin.

  6. Ionizing radiation-induced copolymerization of 2-ethylhexyl acrylate and acrylic acid and ionomer formation

    Science.gov (United States)

    Weaver, Alia

    The ionizing radiation-induced polymerization of acrylate esters is a technique employed for the curing of such materials for a variety of adhesive, coating, ink, and lithographic applications. The work presented in this dissertation involves the synthesis of a copolymer composed of 2-ethylhexyl acrylate (2-EHA) and acrylic acid (AA) using pulsed electron beam and gamma irradiation. The structure and synthesis kinetics of this copolymer were investigated by 1H nuclear magnetic resonance (NMR), electron pulse radiolysis with kinetic spectroscopic detection (PR-KSD), and Fourier transform infrared spectroscopy (FTIR). The effects of total dose, dose rate, and acrylic acid content on the polymerization reaction were studied. The conversion of 2-EHA monomer into polymer at a given total dose was found to be enhanced at lower dose rates and higher concentrations of acrylic acid. The pulse radiolysis investigation of the polymerization of 2-EHA and AA was performed through studies of four different types of systems: (i) neat 2-EHA, (ii) 2-EHA/methanol (MeOH) solutions, (iii) mixtures of 2-EHA and AA, and (iv) 2-EHA/AA/MeOH solutions. The build-up of carbon-centered neutral 2-EHA free radicals in neat 2-EHA was found to obey a second order rate law with a rate coefficient of ((7 +/- 3) x 108)epsilon EHA·, whereas in 2-EHA/AA mixtures it was found to obey a pseudo-first order rate law with a rate coefficient of (1.5 +/- 0.3) x 10 10 mol-1 dm3 s-1. This phenomenon is suggested to originate in the increased H+ ion concentration in the presence of acrylic acid, which leads to a faster neutralization step of 2-EHA radical anions as they are transformed into neutral free radicals during the initiation step of the reaction. An investigation of the formation of ion-containing copolymers (known as ionomers) was performed using the radiation-synthesized poly(2-EHA-co-AA) and iron cations. Verification of successful incorporation of iron into the copolymer was identified by an

  7. Occupational dermatitis due to an epoxy acrylate.

    Science.gov (United States)

    Kanerva, L; Jolanki, R; Estlander, T

    1986-02-01

    A dental assistant developed sensitivity to dental restorative materials within 3 months of starting to use them. They contained the epoxy acrylate BIS-GMA, which is the most commonly used dimethacrylate monomer in dental composite restorations. She was positive to a patch test with BIS-GMA, which was the probable allergen, and epoxy resin, but this substance was not present in the materials used, as shown by high performance liquid chromatography. The patient was also allergic to the disinfectant Desimex i containing dodecyl diaminoethyl glycine.

  8. Comparison of Candida Albicans Adherence to Conventional Acrylic Denture Base Materials and Injection Molding Acrylic Materials.

    Science.gov (United States)

    Aslanimehr, Masoomeh; Rezvani, Shirin; Mahmoudi, Ali; Moosavi, Najmeh

    2017-03-01

    Candida species are believed to play an important role in initiation and progression of denture stomatitis. The type of the denture material also influences the adhesion of candida and development of stomatitis. The aim of this study was comparing the adherence of candida albicans to the conventional and injection molding acrylic denture base materials. Twenty injection molding and 20 conventional pressure pack acrylic discs (10×10×2 mm) were prepared according to their manufacturer's instructions. Immediately before the study, samples were placed in sterile water for 3 days to remove residual monomers. The samples were then sterilized using an ultraviolet light unit for 10 minutes. 1×10 8 Cfu/ml suspension of candida albicans ATCC-10231 was prepared from 48 h cultured organism on sabouraud dextrose agar plates incubated at 37oC. 100 μL of this suspension was placed on the surface of each disk. After being incubated at 37oC for 1 hour, the samples were washed with normal saline to remove non-adherent cells. Attached cells were counted using the colony count method after shaking at 3000 rmp for 20 seconds. Finally, each group was tested for 108 times and the data were statistically analyzed by t-test. Quantitative analysis revealed that differences in colony count average of candida albicans adherence to conventional acrylic materials (8.3×10 3 ) comparing to injection molding acrylic resins (6×10 3 ) were statistically significant ( p injection acrylic resin materials makes them valuable for patients with high risk of denture stomatitis.

  9. Acrylate in Phaeocystis colonies does not affect the surrounding bacteria

    NARCIS (Netherlands)

    Noordkamp, DJB; Gieskes, WWC; Gottschal, JC; Forney, LJ; van Rijssel, M

    Acrylate accumulates to concentrations of 1.3-6.5 mM in the mucus of Phaeocystis colonies and may have an effect on the surrounding bacterial community, either as an inhibitor or as a carbon source. Both in the held and in the laboratory, effects of acrylate on bacterial growth and on its

  10. Artificial saliva effect on toxic substances release from acrylic resins.

    Science.gov (United States)

    Kostić, Milena; Krunić, Nebojša; Najman, Stevo; Nikolić, Ljubiša; Nikolić, Vesna; Rajković, Jelena; Petrović, Milica; Igić, Marko; Ignjatović, Aleksandra

    2015-10-01

    Acrylic-based resins are intensively used in dentistry practice as restorative or denture-base materials. The purpose of this study was to analyze the surface structure of denture base resins and the amount of released potentially toxic substances (PTS) immediately upon polymerization and incubation in different types of artificial saliva. Storage of acrylic samples in two models of artificial saliva were performed in a water bath at the temperature of 37 +/- 1 degrees C. Analysis of the surface structure of samples was carned out using scanning electronic microscopy analysis immedidtely after polymerization and after the 30-day incubation. The amounts of PTS per day, week and month extracts were measured using high-pressure liquid chromatography. Surface design and amount of PTS in acrylic materials were different and depended on the types and duration of polymerization. The surfaces of tested acrylates became flatter after immersing in solutions of artificial saliva. The degree of acrylic materials release was not dependent on the applied model of artificial saliva. In order to improve biological features of acrylic resin materials, it was recommended that dentures lined with soft or hard cold-polymerized acrylates should be kept at least 1 to 7 days in water before being given to a patient. So, as to reach high degree of biocompatibility preparation of prosthetic restorations from heat-polymerized acrylate was unnecessary.

  11. Artificial saliva effect on toxic substances release from acrylic resins

    Directory of Open Access Journals (Sweden)

    Kostić Milena

    2015-01-01

    Full Text Available Background/Aim. Acrylic-based resins are intensively used in dentistry practice as restorative or denture-base materials. The purpose of this study was to analyze the surface structure of denture base resins and the amount of released potentially toxic substances (PTS immediately upon polymerization and incubation in different types of artificial saliva. Methods. Storage of acrylic samples in two models of artificial saliva were performed in a water bath at the temperature of 37 ± 1°C. Analysis of the surface structure of samples was carried out using scanning electronic microscopy analysis immediately after polymerization and after the 30-day incubation. The amounts of PTS per day, week and month extracts were measured using high-pressure liquid chromatography. Results. Surface design and amount of PTS in acrylic materials were different and depended on the types and duration of polymerization. The surfaces of tested acrylates became flatter after immersing in solutions of artificial saliva. The degree of acrylic materials release was not dependent on the applied model of artificial saliva. Conclusion. In order to improve biological features of acrylic resin materials, it was recommended that dentures lined with soft or hard coldpolymerized acrylates should be kept at least 1 to 7 days in water before being given to a patient. So, as to reach high degree of biocompatibility preparation of prosthetic restorations from heat-polymerized acrylate was unnecessary. [Projekat Ministarstva nauke Republike Srbije, br. 41017

  12. 40 CFR 721.10082 - Amine modified monomer acrylate (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amine modified monomer acrylate (generic). 721.10082 Section 721.10082 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.10082 Amine modified monomer acrylate (generic). (a) Chemical substance...

  13. Occupational fingertip eczema from acrylates in a manicurist

    Directory of Open Access Journals (Sweden)

    Denitza Zheleva

    2015-04-01

    Full Text Available Occupational hand eczema due to acrylates present in the workplace is a disease frequently reported among dentists, printers, and fiberglass workers. Acrylate monomers are used in the production of a great variety of polymers, including nail cosmetics. Our case report demonstrates a rare clinical presentations of allergic contact dermatitis from acrylic nails. Our patient was working as a manicurist and the diagnostic analyses revealed sensitation to some of the (meth acrylate compounds of her new nail cosmetics. Sculptured artificial acrylic and UV-hardened nails s are widely used in developed countries and they are gaining more and more popularity. We expect an increase in the number of cases of contact allergic dermatitis among manicurists and customers.

  14. UV-Curable Aliphatic Silicone Acrylate Organic-Inorganic Hybrid Coatings with Antibacterial Activity.

    Science.gov (United States)

    Jankauskaitė, Virginija; Lazauskas, Algirdas; Griškonis, Egidijus; Lisauskaitė, Aistė; Žukienė, Kristina

    2017-06-09

    The most effective means to protect against bacterial invasion and to reduce the risk of healthcare-associated infections are antibacterial components synthesis. In this study, a novel process for the synthesis of organic-inorganic hybrid coatings containing silver nanoparticles is presented. Silver nanoparticles and polymer formation proceeds simultaneously through the in situ photoreduction of silver salt to silver nanoparticles and UV-crosslinking of bifunctional aliphatic silicone acrylate. The nanocomposite films with 0.5-1.43 wt % of silver nanoparticles concentration were obtained and investigated. The formation of silver nanoparticles in polymer matrix was confirmed via UV-visible spectroscopy, X-ray diffraction (XRD), Fourier transform infrared spectroscopy, scanning electron spectroscopy, and energy dispersive spectroscopy. Our investigations clearly show the formation of silver nanoparticles in silicone acrylate network. Direct photoreduction of silver salt by UV-radiation in the organic media produced silver nanoparticles exhibiting cubic crystal structure. The size of nanoparticles was determined to be near 20 ± 5 nm. The antibacterial activities of coatings were determined using the disc diffusion and direct contact methods. UV-curable silicone acrylate hybrid coatings exhibited antibacterial activity against harmful bacteria strains.

  15. Bond strength test of acrylic artificial teeth with prosthetic base

    Directory of Open Access Journals (Sweden)

    Erna Kurnikasari

    2008-07-01

    Full Text Available Denture consists of acrylic artificial teeth and acrylic prothesis base bond chemically with a bond strength of 315 kgF/cm2. Most of the commercial acrylic artificial teeth do not specify their specifications and all of those acrylic artificial teeth do not include mechanical data (bond strength. The aim of this study is to discover which acrylic artificial teeth meet ADA specification no. 15. This study is a descriptive analytic study performed to 5 acrylic artificial teeth posterior brands commonly used by dentists and technicians. From each brand, 3 sample teeth were taken. The acrylic artificial teeth were prepared into a rectangular shape and were attached between acrylic prothesis base simulation and jigs. The sample was given tensile load using a Universal Testing Machine. The amount of force that causes the teeth to be fractured was recorded and the bond strength was calculated. The results of the study show that the average value for the five acrylic artificial teeth for the five brands were as followed: Brand A, 125.993 kgF/cm2; B, 188.457 kgF/cm2; C, 175.880 kgF/cm2; D, 153.373 kgF/cm2; E, 82.839 kgF/cm2. The data can be tested statistically by using One Way ANOVA test and Dunnett test (alpha = 0.05. From the study, it is concluded that the five acrylic artificial teeth have a bond strength below the ADA specification no. 15.

  16. Allergic contact dermatitis from acrylic nails in a flamenco guitarist.

    Science.gov (United States)

    Alcántara-Nicolás, F A; Pastor-Nieto, M A; Sánchez-Herreros, C; Pérez-Mesonero, R; Melgar-Molero, V; Ballano, A; De-Eusebio, E

    2016-12-01

    Acrylates are molecules that are well known for their strong sensitizing properties. Historically, many beauticians and individuals using store-bought artificial nail products have developed allergic contact dermatitis from acrylates. More recently, the use of acrylic nails among flamenco guitarists to strengthen their nails has become very popular. A 40-year-old non-atopic male patient working as a flamenco guitarist developed dystrophy, onycholysis and paronychia involving the first four nails of his right hand. The lesions were confined to the fingers where acrylic materials were used in order to strengthen his nails to play the guitar. He noticed improvement whenever he stopped using these materials and intense itching and worsening when he began reusing them. Patch tests were performed and positive results obtained with 2-hydroxyethyl methacrylate (2-HEMA), 2-hydroxyethyl acrylate (2-HEA), ethyleneglycol-dimethacrylate (EGDMA) and 2-hydroxypropyl methacrylate (2-HPMA). The patient was diagnosed with occupational allergic contact dermatitis likely caused by acrylic nails. Artificial nails can contain many kinds of acrylic monomers but most cases of contact dermatitis are induced by 2-HEMA, 2-HPMA and EGDMA. This is the first reported case of occupational allergic contact dermatitis from acrylates in artificial nails in a professional flamenco guitar player. Since the practice of self-applying acrylic nail products is becoming very popular within flamenco musicians, we believe that dermatology and occupational medicine specialists should be made aware of the potentially increasing risk of sensitization from acrylates in this setting. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  17. Acrylic acid removal by acrylic acid utilizing bacteria from acrylonitrile-butadiene-styrene resin manufactured wastewater treatment system.

    Science.gov (United States)

    Wang, C C; Lee, C M

    2006-01-01

    The aim of this study is to isolate the acrylic acid utilizing bacteria from the ABS resin manufactured wastewater treatment system. The bacteria should have the ability to remove acrylic acid and tolerate the acrylonitrile and acrylamide toxicity. The aim is also to understand the performance of isolated pure strain for treating different initial acrylic acid concentrations from synthetic wastewater. The results are: twenty strains were isolated from the ABS resin manufactured wastewater treatment system and twelve of them could utilize 600 mg/l acrylic acid for growth. Seven of twelve strains could tolerate the acrylonitrile and acrylamide toxicity, when the concentration was below 300 mg/l. Bacillus thuringiensis was one of the seven strains and the optimum growth temperature was 32 degrees C. Bacillus thuringiensis could utilize acrylic acid for growth, when the initial acrylic acid concentration was below 1,690.4 mg/l. Besides this, when the initial acrylic acid concentration was below 606.8 mg/l, the acrylic acid removal efficiency exceeded 96.3%. Bacillus thuringiensis could tolerate 295.7 mg/l acrylamide and 198.4 mg/l acrylonitrile toxicity but could not tolerate 297.3 mg/l epsilon-caprolactam.

  18. Comparison of the Retinal Straylight in Pseudophakic Eyes with PMMA, Hydrophobic Acrylic, and Hydrophilic Acrylic Spherical Intraocular Lens

    Directory of Open Access Journals (Sweden)

    Ya-wen Guo

    2014-01-01

    Full Text Available Purpose. To investigate the intraocular straylight value after cataract surgery. Methods. In this study, 76 eyes from 62 patients were subdivided into three groups. A hydrophobic acrylic, a hydrophilic acrylic, and a PMMA IOL were respectively, implanted in 24 eyes, 28 eyes, and 24 eyes. Straylight was measured using C-Quant at 1 week and 1 month postoperatively in natural and dilated pupils. Results. The hydrophilic acrylic IOLs showed significantly lower straylight values than those of the hydrophobic acrylic IOLs in dilated pupils at 1 week and 1 month after surgery (P0.05. Moreover, no significant difference was found in straylight between natural and dilated pupils in each group at 1 week and 1 month postoperatively (P>0.05. Conclusions. Although the hydrophobic acrylic IOL induced more intraocular straylight, straylight differences among the 3 IOLs were minimal. Pupil size showed no effect on intraocular straylight; the intraocular straylight was stable 1 week after surgery.

  19. Use of Acrylic Acid Sodium Acrylate Polymer to Maintain Cocoa Seed Viability

    Directory of Open Access Journals (Sweden)

    Pudji Rahardjo

    2010-08-01

    Full Text Available The main problem of cocoa seed storage is moisture content of the seeds because cocoa seeds will germinate if cocoa seeds moisture content is high. The objective of this research is to maintain the cocoa seeds viability in storage using acrylic acid sodium acrylate polymer (AASAP. The function of AASAP is to absorb humidity in storage due to their ability to retain water and to prevent water loss. The experiment was conducted in a laboratory of Indonesian Coffee and Cocoa Research Institute and in Kaliwining Experimental Garden. This experiment was arranged by factorial randomized complete design, in wich AASAP dosages 0%; 0.1% (0.1 g/100 seeds; 0.2% (0.2 g/100 seeds, 0.3% (0.3 g/100 seeds, 0,4% (0,4g/100 seeds, combined with seeds storage period 1, 2, 3 and 4 weeks. The experiment used 3 replications and each repli cation used 100 seeds. Parameter of observation consisted of percentage of seeds germinated in storage, percentage of seeds infected by fungi in storage, seeds moisture content, percentage of seeds germination after storage, and early growth of cocoa seedlings. The results of the experiment showed that AASAP application with some dosages cocoa seeds storage cause to germinate in storage during 2 weeks. AASAP application with some dosages in cocoa seeds storage for 2 weeks would not result in infection by fungi and did not significantly affect seed germination after storage for 1, 2 and 4 weeks, and percentage of germination of cocoa seed after storage for 3 weeks decreased with increase dosage of AASAP. Higher dosage of AASAP would reduce early growth of cocoa seedling. Key words : Theobroma cacao, seed, acrylic acid sodium acrylate, seed storage, viabilty.

  20. An epidemic of occupational contact dermatitis from an acrylic glue.

    Science.gov (United States)

    Kiec-Swierczynska, Marta; Krecisz, Beata; Swierczynska-Machura, Dominika; Zaremba, Joanna

    2005-03-01

    Dermatological examinations were performed in 81 workers involved in the manufacture of electric coils for television displays, who had worked for 4 years in contact with a glue containing isobornyl acrylate, acrylic acid, N,N dimethyleneacrylamide, phosphine oxide, bis(2,6-dimethoxybenzoyl) (2,4,4-trimethylpentyl)- and beta-carboxyethyl acrylate. The glue was cured by 350-500-nm ultraviolet and visible radiations. Acrylate-specific dermal lesions were detected in 21 (25.9%) people. Occupational irritant contact dermatitis was diagnosed in 12 (15%) of the workers and occupational allergic contact dermatitis in 9 (11.2%). 12 people reacted to acrylates. Cross-reactions with methacrylates were not observed. The highest number of positive tests was obtained with triethyleneglycol diacrylate (10 people) and diethyleneglycol diacrylate (9), followed by 1,6-hexanediol diacrylate (5), 1,4-butanediol diacrylate (4), beta-carboxyethyl acrylate (3), tripropyleneglycol diacrylate (2) and pentaerythritol triacrylate (2). No cases of allergy to isobornyl acrylate, N,N-methylenebisacrylamide or phosphine oxide were noted.

  1. Hydrophilic surface modification of acrylate-based biomaterials.

    Science.gov (United States)

    Arnal-Pastor, M; Comín-Cebrián, S; Martínez-Ramos, C; Monleón Pradas, M; Vallés-Lluch, A

    2016-04-01

    Acrylic polymers have proved to be excellent with regard to cell adhesion, colonization and survival, in vitro and in vivo. Highly ordered and regular pore structures thereof can be produced with the help of polyamide templates, which are removed with nitric acid. This treatment converts a fraction of the ethyl acrylate side groups into acrylic acid, turning poly(ethyl acrylate) scaffolds into a more hydrophilic and pH-sensitive substrate, while its good biological performance remains intact. To quantify the extent of such a modification, and be able to characterize the degree of hydrophilicity of poly(ethyl acrylate), poly(ethyl acrylate) was treated with acid for different times (four, nine and 17 days), and compared with poly(acrylic acid) and a 90/10%wt. EA/AAc copolymer (P(EA-co-AAc)). The biological performance was also assessed for samples immersed in acid up to four days and the copolymer, and it was found that the incorporation of acidic units on the material surface was not prejudicial for cells. This surface modification of 3D porous hydrophobic scaffolds makes easier the wetting with culture medium and aqueous solutions in general, and thus represents an advantage in the manageability of the scaffolds. © The Author(s) 2016.

  2. COMPARATIVE ANALYSIS OF WATER SORPTION BY DIFFERENT ACRYLIC MATERIALS

    Directory of Open Access Journals (Sweden)

    Milena Kostić

    2014-06-01

    Full Text Available Acrylic materials are used daily for the production of mobile dental restorations and orthodontic appliances. The presence of residual monomer, as a product of incomplete polymerisation of material, results in more porous structure of the material, which greatly reduces the mechanical and physical quality of the acrylic restorations and increases the absorption of liquids. The aim of this study was to examine the water absorption of different types of resin material. In the study it was assumed that the cold polymerized acrylates show a greater potential for absorbing fluid from the environment in relation to the hot polymerized acrylic. The study included two hot and two cold polymerized acrylates, and cold polymerized acrylate impregnated with aesthetic pearls. In order to determine the degree of water absorption, the mass of the samples was measured before and after one day, seven days and thirty days of immersion in a water bath of body temperature. The tested hot and cold polymerized acrylates after immersion in water bath showed standard values of water absorption. The degree of water absorption was not significantly influenced by the type and manner of polymerisation. Water absorption values were significantly higher after seven days and thirty days of water storage relative to the observational period of one day.

  3. Dynamical mechanical analysis of photocrosslinked hyperbranched urethane acrylates

    Directory of Open Access Journals (Sweden)

    BRANKO DUNJIC

    2004-06-01

    Full Text Available A series of acrylate functionalized samples based on hyperbranched hydroxy-terminated polyesters with different molecular weights and different degrees of acrylation were synthesized. The obtained urethane acrylates were slightly yellow viscose liquids. Their composition was characterized by FTIR and 1H-NMR spectroscopy and their molecular weights were measured by GPC. All the synthesized samples were diluted with 25 wt.% 1,4-butanediol dimethacrylate (BDDM. The rheological properties of the uncured samples and the dynamic mechanical properties of the UV cured samples were examined. All the samples exhibit Newtonian behavior, which indicates the absence of physical entanglements in these polymers. The viscosity increases with increasing number of acrylic groups per molecule. The glass transition temperature of the UV cured samples increases with increasing the number of acrylic groups per molecule. The value of the storage modulus in the rubber-elastic plateau and the cross-link density increase with increasing number of acrylic groups per molecule. The formed networks are inhomogeneous and the residual unsaturation is the highest in the samples with the largest number of acrylic groups per molecule.

  4. Electrochemical characterization of aminated acrylic conducting polymer

    Energy Technology Data Exchange (ETDEWEB)

    Rashid, Norma Mohammad [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Lestari Universiti Kebangsaan Malaysia (UKM), 43600 Bangi, Selangor Darul Ehsan (Malaysia); Heng, Lee Yook [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Lestari Universiti Kebangsaan Malaysia (UKM), 43600 Bangi, Selangor Darul Ehsan (Malaysia); Southeast Asia Disaster Prevention Research Initiative, Lestari Universiti Kebangsaan Malaysia (UKM), 43600 Bangi, Selangor Darul Ehsan (Malaysia); Ling, Tan Ling [Southeast Asia Disaster Prevention Research Initiative, Lestari Universiti Kebangsaan Malaysia (UKM), 43600 Bangi, Selangor Darul Ehsan (Malaysia)

    2015-09-25

    New attempt has been made to synthesize aminated acrylic conducting polymer (AACP) using precursor of phenylvinylsulfoxide (PVS). The process was conducted via the integration of microemulsion and photopolymerization techniques. It has been utilized for covalent immobilization of amino groups by the adding of N-achryiloxisuccinimide (NAS). Thermal eliminating of benzene sulfenic acids from PVS has been done at 250 °C to form electroactive polyacetylene (PA) segment. Characterization of AACP has been conducted using fourier transform infrared (FTIR), scanning electron microscopy (SEM) and linear sweep cyclic voltammetry (CV). A range of 0.3-1.25μm particle size obtained from SEM characterization. A quasi-reversible system performed as shown in electrochemical study.

  5. Chemo-enzymatic synthesis route to poly(glucosyl-acrylates) using glucosidase from almonds

    NARCIS (Netherlands)

    Kloosterman, Wouter M. J.; Roest, Steven; Priatna, Siti R.; Stavila, Erythrina; Loos, Katja

    2014-01-01

    Novel types of glucosyl-acrylate monomers are obtained by beta-glucosidase from almond catalyzed glycosidation reaction. The saccharide-acrylate monomers were synthesized by reaction of D-glucose with hydroxyl functional acrylates: 2-hydroxyethyl acrylate (2-HEA), 2-hydroxyethyl methacrylate

  6. The sensitizing potential of 2-ethylhexyl acrylate in the guinea pig.

    Science.gov (United States)

    Waegemaekers, T H; van der Walle, H B

    1983-09-01

    The sensitizing potential of 2-ethylhexyl acrylate in the guinea pig could be demonstrated by Freund's Complete Adjuvant Test. This acrylate ester is a common constituent of adhesive tape. Allergic reactions to several brands of adhesive tape were not observed in 2-ethylhexyl acrylate sensitized animals. Cross reactions with other acrylic monomers were observed.

  7. 21 CFR 177.1990 - Vinylidene chloride/methyl acrylate copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Vinylidene chloride/methyl acrylate copolymers. 177... chloride/methyl acrylate copolymers. The vinylidene chloride/methyl acrylate copolymers (CAS Reg. No. 25038...) Identity. For the purposes of this section vinylidene chloride/methyl acrylate copolymers consist of basic...

  8. We can see clearly now: optical clearing and kidney morphometrics.

    Science.gov (United States)

    Puelles, Victor G; Moeller, Marcus J; Bertram, John F

    2017-05-01

    For more than a century, kidney microscopic imaging was driven by the need for greater and greater resolution. This was in part provided by the analysis of thinner tissue sections. As a result, most kidney morphometry was performed in 'two' dimensions, largely ignoring the three-dimensionality of kidney tissue and cells. Although stereological techniques address this issue, they have generally been considered laborious and expensive and thereby unattractive for routine use. The past 2 decades have witnessed the development of optical clearing techniques, which enables visualization of thick slices of kidney tissue and even whole kidneys. This review describes the three main optical clearing strategies (solvent-based, aqueous-based and hydrogel embedding) with their respective advantages and disadvantages. We also describe how optical clearing provides new approaches to kidney morphometrics, including general kidney morphology (i.e. identification and quantitation of atubular glomeruli), glomerular numbers and volumes, numbers of specific glomerular cells (i.e. podocytes) and cell-specific stress-related changes (i.e. foot process effacement). The new clearing and morphometric approaches described in this review provide a new toolbox for imaging and quantification of kidney microanatomy. These approaches will make it easier to visualize the three-dimensional microanatomy of the kidney and decrease our reliance on biased two-dimensional morphometric techniques and time-consuming stereological approaches. They will also accelerate our research of structure-function relations in the healthy and diseased kidney.

  9. Occupational contact dermatitis to acrylates in a manicurist.

    Science.gov (United States)

    Kiec-Swierczynska, M; Krecisz, B; Chomiczewska-Skora, D

    2013-07-01

    We report the case of a manicurist who developed an allergic skin reaction to acrylates, manifested by bullous lesions on fingertips and eczema of the hands and ears. Patch tests showed positive reactions to 2-hydroxyethyl methacrylate, 2-hydroxypropyl methacrylate, ethyleneglycol dimethacrylate, triethyleneglycol dimethacrylate, 1,6-hexandiol diacrylate, 2-hydroxyethyl acrylate and triethyleneglycol diacrylate. Because of her skin disorder, she had to give up her job. She was not correctly advised on retraining and started to work as a dental nurse. Soon after re-exposure to acrylates in dental materials, she experienced recurrence of the skin symptoms.

  10. Methods for the synthesis of deuterated acrylate salts

    Science.gov (United States)

    Yang, Jun; Bonnesen, Peter V.; Hong, Kunlun

    2014-09-09

    A method for synthesizing a deuterated acrylate of the Formula (1), the method comprising: (i) deuterating a propiolate compound of Formula (2) to a methyne-deuterated propiolate compound of Formula (3) in the presence of a base and D.sub.2O: and (ii) reductively deuterating the methyne-deuterated propiolate compound of Formula (3) in a reaction solvent in the presence of deuterium gas and a palladium-containing catalyst to afford the deuterated acrylate of the Formula (1). The resulting deuterated acrylate compounds, derivatives thereof, and polymers derived therefrom are also described.

  11. Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate

    Energy Technology Data Exchange (ETDEWEB)

    Binder, Thomas [Archer Daniels Midland Company, Decatur, IL (United States); Erpelding, Michael [Archer Daniels Midland Company, Decatur, IL (United States); Schmid, Josef [Archer Daniels Midland Company, Decatur, IL (United States); Chin, Andrew [Archer Daniels Midland Company, Decatur, IL (United States); Sammons, Rhea [Archer Daniels Midland Company, Decatur, IL (United States); Rockafellow, Erin [Archer Daniels Midland Company, Decatur, IL (United States)

    2015-04-10

    Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate. The purpose of Archer Daniels Midlands Integrated Biorefinery (IBR) was to demonstrate a modified acetosolv process on corn stover. It would show the fractionation of crop residue to distinct fractions of cellulose, hemicellulose, and lignin. The cellulose and hemicellulose fractions would be further converted to ethanol as the primary product and a fraction of the sugars would be catalytically converted to acrylic acid, with butyl acrylate the final product. These primary steps have been demonstrated.

  12. Investigation of Acrylic Acid at High Pressure using Neutron Diffraction

    DEFF Research Database (Denmark)

    Johnston, Blair F.; Marshall, William G.; Parsons, Simon

    2014-01-01

    This article details the exploration of perdeuterated acrylic acid at high pressure using neutron diffraction. The structural changes that occur in acrylic acid-d4 are followed via diffraction and rationalised using the Pixel method. Acrylic acid undergoes a reconstructive phase transition to a new...... phase at ~0.8 GPa and remains molecular to 7.2 GPa before polymerising on decompression to ambient pressure. The resulting product is analysed via Raman, FT-IR spectroscopy and Differential Scanning Calorimetry and found to possess a different molecular structure compared with polymers produced via...

  13. [Determination of 9 residual acrylic monomers in acrylic resins by gas chromatography-mass spectrometry coupled with microwave assisted extraction].

    Science.gov (United States)

    Lai, Ying; Lin, Rui; Cai, Luxin; Ge, Xiuxiu; Huang, Changchun

    2012-01-01

    A reliable gas chromatography-mass spectrometry (GC-MS) method was developed for the determination of 9 residual acrylic monomers (methyl acrylate, ethyl acrylate, methyl methacrylate, ethyl methacrylate, n-butyl acrylate, butyl methacrylate, styrene, acrylic acid and methacrylic acid) in acrylic resins. Solid resin was precipitated with methanol after microwave assisted extraction with ethyl acetate for 30 min, and liquid resin was diluted with methanol directly. The nine acrylic monomers got a good separation within 20 min on a DB-WAX column. The limits of quantification (LOQs, S/N = 10) of the method were in the range of 1-10 mg/kg for liquid resin and 3-50 mg/kg for solid resin. The calibration curves were linear within 1-500 mg/L range with correlation coefficients above 0. 995. The recoveries ranged from 84.4% to 108.6% at five spiked levels. The sensitivity, recovery and selectivity of the method can fully meet the requirements of practical work.

  14. Media Language, Clear or Obscure

    DEFF Research Database (Denmark)

    Jakobsen, Bjarne le Fevre; Ejstrup, Michael

    2015-01-01

    growth in diversity, means that media need to be very cognizant of the stringency with which they handle the advice to be linguistically clear and concise. The need to pay great attention to situational awareness is highly visible and intrusive. Attention to situational awareness seems to be crucial...... where it is important for mutual understanding that we be clear and concise. This is true of instructions for electronic equipment and for household appliances. Here, linguistic brevity and clarity may be preferable, but not in other cases. Culture, globalization, and the recognition of ever faster...

  15. Media Language, Clear or Obscure

    DEFF Research Database (Denmark)

    Ejstrup, Michael; le Fevre Jakobsen, Bjarne

    2015-01-01

    it is important for mutual understanding that we be clear and concise. This is true of instructions for electronic equipment and for household appliances. Here, linguistic brevity and clarity may be preferable, but not in other cases. Culture, globalization, and the recognition of ever faster growth in diversity...

  16. Central Clearing of OTC Derivatives

    DEFF Research Database (Denmark)

    Cont, Rama; Kokholm, Thomas

    2014-01-01

    We study the impact of central clearing of over-the-counter (OTC) transactions on counterparty exposures in a market with OTC transactions across several asset classes with heterogeneous characteristics. The impact of introducing a central counterparty (CCP) on expected interdealer exposure is de...

  17. Media Language, Clear or Obscure

    DEFF Research Database (Denmark)

    Ejstrup, Michael; le Fevre Jakobsen, Bjarne

    2015-01-01

    , means that media need to be very cognizant of the stringency with which they handle the advice to be linguistically clear and concise. The need to pay great attention to situational awareness is highly visible and intrusive. Attention to situational awareness seems to be crucial for the survival of free...

  18. Emulsion Polymerization of Butyl Acrylate: Spin Trapping and EPR Study

    Science.gov (United States)

    Kim, S.; Westmoreland, D.

    1994-01-01

    The propagating radical in the emulsion polymerization reaction of butyl acrylate was detected by Electron Paramagnetic Resonance spectroscopy using two spin trapping agents, 2-methyl-2nitrosopropane and alpha -N-tert-butylnitrone.

  19. Synthesis and characterization of polycaprolactone/acrylic acid ...

    Indian Academy of Sciences (India)

    ... of polycaprolactone/acrylic acid (PCL/AA) hydrogel for controlled drug delivery ... by measuring diffusion coefficient () and equilibrium water content (EWC). Network formation, morphology and crystallinity of PCL/AA hydrogels were ...

  20. Performance behavior of modified cellulosic fabrics using polyurethane acrylate copolymer.

    Science.gov (United States)

    Zuber, Mohammad; Shah, Sayyed Asim Ali; Jamil, Tahir; Asghar, Muhammad Irfan

    2014-06-01

    The surface of the cellulosic fabrics was modified using self-prepared emulsions of polyurethane acrylate copolymers (PUACs). PUACs were prepared by varying the molecular weight of polycaprolactone diol (PCL). The PCL was reacted with isophorone diisocyanate (IPDI) and chain was extended with 2-hydroxy ethyl acrylate (HEA) to form vinyl terminated polyurethane (VTPU) preploymer. The VTPU was further co-polymerized through free radical polymerization with butyl acrylate in different proportions. The FT-IR spectra of monomers, prepolymers and copolymers assured the formation of proposed PUACs structure. The various concentrations of prepared PUACs were applied onto the different fabric samples using dip-padding techniques. The results revealed that the application of polyurethane butyl acrylate copolymer showed a pronounced effect on the tear strength and pilling resistance of the treated fabrics. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. [Treatment of acrylate wastewater by electrocatalytic reduction process].

    Science.gov (United States)

    Yu, Li-Na; Song, Yu-Dong; Zhou, Yue-Xi; Zhu, Shu-Quan; Zheng, Sheng-Zhi; Ll, Si-Min

    2011-10-01

    High-concentration acrylate wastewater was treated by an electrocatalytic reduction process. The effects of the cation exchange membrane (CEM) and cathode materials on acrylate reduction were investigated. It indicated that the acrylate could be reduced to propionate acid efficiently by the electrocatalytic reduction process. The addition of CEM to separator with the cathode and anode could significantly improve current efficiency. The cathode materials had significant effect on the reduction of acrylate. The current efficiency by Pd/Nickel foam, was greater than 90%, while those by nickel foam, the carbon fibers and the stainless steel decreased successively. Toxicity of the wastewater decreased considerably and methane production rate in the biochemical methane potential (BMP) test increased greatly after the electrocatalytic reduction process.

  2. Use of acrylic sheet molds for elastomeric products

    Science.gov (United States)

    Heisman, R. M.; Koerner, A. E.; Messineo, S. M.

    1970-01-01

    Molds constructed of acrylic sheet are more easily machined than metal, are transparent to ensure complete filling during injection, and have smooth surfaces free of contamination. Technique eliminates flashing on molded parts and mold release agents.

  3. A facile one-pot synthesis of acrylated hyaluronic acid.

    Science.gov (United States)

    A, Sigen; Xu, Qian; McMichael, Peter; Gao, Yongsheng; Li, Xiaolin; Wang, Xi; Greiser, Udo; Zhou, Dezhong; Wang, Wenxin

    2018-01-25

    The synthesis of acrylated hyaluronic acid (HA-A) normally requires 2 to 3 steps of modification, needs laborious purification and also increases the risks of HA degradation. Here, we report that the conjugation of acrylate groups to hyaluronic acid can be successfully achieved via a new facile one-pot approach. Two types of new HA-A hydrogels (via chemical or UV crosslinking) were developed and applied for 3D cell encapsulation.

  4. Artificial saliva effect on toxic substances release from acrylic resins

    OpenAIRE

    Kostić Milena; Krunić Nebojša; Najman Stevo; Nikolić Ljubiša; Nikolić Vesna; Rajković Jelena; Petrović Milica; Igić Marko; Ignjatović Aleksandra

    2015-01-01

    Background/Aim. Acrylic-based resins are intensively used in dentistry practice as restorative or denture-base materials. The purpose of this study was to analyze the surface structure of denture base resins and the amount of released potentially toxic substances (PTS) immediately upon polymerization and incubation in different types of artificial saliva. Methods. Storage of acrylic samples in two models of artificial saliva were performed in a water bath a...

  5. Synthesis and Reactivity of Aluminized Fluorinated Acrylic (AIFA) Nanocomposites (Postprint)

    Science.gov (United States)

    2012-06-18

    REACTIVITY OF ALUMINIZED FLUORINATED ACRYLIC (ALFA) NANOCOMPOSITES (POSTPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...throughout the energetic materials community due to their strong reactivity with aluminum powders . Herein, we report the synthesis of a novel...These materials, which we have termed aluminized fluorinated acrylic (AlFA) composites, have been prepared with particle contents ranging from 10% to

  6. ELECTRON BEAM CURING OF EPOXY ACRYLATE COATINGS ON MEDIUM-DENSITY FIBERBOARD

    Directory of Open Access Journals (Sweden)

    Sugiarto Danu

    2010-06-01

    Full Text Available Most of the medium-density fiberboard (MDF as an engineered woods need surface coating process before entering final products, such as furniture and building materials. The wood surface should be covered for surface protection from damage during service life as well as to enhance its appearance. Surface coating of MDF was conducted using epoxy acrylate resin either for clear and pigmented coatings. Titanium dioxide was used for white pigmented coatings. Coating was conducted at variation thickness level of 30 to 150 μm. Curing was carried out by using 350 kV electron beam accelerator at 1.35 mA current and 1.6 m/min conveyor speed to get the absorbed dose of 3 Mrad. Effect of coating thickness was evaluated by measuring the physical, mechanical and chemical properties of cured samples, i.e., hardness, gloss, transparency, adhesion, abrasion resistance, and chemical, solvent and stain resistance. Experimental results showed that pendulum hardness and abrasion resistance slightly increased whereas gloss, transparency and adhesion resistance decreased with increasing coating thickness, while chemical, solvent and stain resistance remains similar. In general, clear coating provides better properties than pigmented coating.   Keywords: electron-beam; coating; epoxy-acrylate; pigment; medium-density fiberboard

  7. Poly(meth)acrylates obtained by cascade reaction.

    Science.gov (United States)

    Popescu, Dragos; Keul, Helmut; Moeller, Martin

    2011-04-04

    Preparation, purification, and stabilization of functional (meth)acrylates with a high dipole moment are complex, laborious, and expensive processes. In order to avoid purification and stabilization of the highly reactive functional monomers, a concept of cascade reactions was developed comprising enzymatic monomer synthesis and radical polymerization. Transacylation of methyl acrylate (MA) and methyl methacrylate (MMA) with different functional alcohols, diols, and triols (1,2,6-hexanetriol and glycerol) in the presence of Novozyme 435 led to functional (meth)acrylates. After the removal of the enzyme by means of filtration, removal of excess (meth)acrylate and/or addition of a new monomer, e.g., 2-hydroxyethyl (meth)acrylate the (co)polymerization via free radical (FRP) or nitroxide mediated radical polymerization (NMP) resulted in poly[(meth)acrylate]s with predefined functionalities. Hydrophilic, hydrophobic as well as ionic repeating units were assembled within the copolymer. The transacylation of MA and MMA with diols and triols carried out under mild conditions is an easy and rapid process and is suitable for the preparation of sensitive monomers. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. The art of thinking clearly

    CERN Document Server

    Dobelli, Rolf

    2013-01-01

    The Art of Thinking Clearly by world-class thinker and entrepreneur Rolf Dobelli is an eye-opening look at human psychology and reasoning — essential reading for anyone who wants to avoid “cognitive errors” and make better choices in all aspects of their lives. Have you ever: Invested time in something that, with hindsight, just wasn’t worth it? Or continued doing something you knew was bad for you? These are examples of cognitive biases, simple errors we all make in our day-to-day thinking. But by knowing what they are and how to spot them, we can avoid them and make better decisions. Simple, clear, and always surprising, this indispensable book will change the way you think and transform your decision-making—work, at home, every day. It reveals, in 99 short chapters, the most common errors of judgment, and how to avoid them.

  9. Industrially relevant epoxy-acrylate hybrid resin photopolymerizations

    Science.gov (United States)

    Ajiboye, Gbenga I.

    Photopolymerization of epoxy-acrylate hybrid resins takes advantages of inherent properties present in the free-radical and cationic reactions to reduce oxygen inhibition problems that plague free-radical reactions. Similarly, the combined reaction mechanisms reduce moisture sensitivity of the cationic reactions. Despite the advantages of epoxy-acrylate hybrid resins, problems persist that need to be addressed. For example, low conversion and polymerization rate of the epoxides are a problem, because the fast acrylate conversion prevents the epoxide from reaching high conversion. Controlling phase separation is challenging, since two moieties with different properties are reacting. The physical properties of the polymer will be impacted by the availability of different moieties. High shrinkage stress results from the acrylate moiety, causing buckling and cracking in film and coating applications. The overall goal of this study is to use the fundamental knowledge of epoxy-acrylate hybrid resins to formulate industrially viable polymers. In order to achieve this goal, the study focuses on the following objectives: (I) determine the apparent activation energy of the hybrid monomer METHB, (II) increase epoxide conversion and polymerization rate of hybrid formulations, and (III) control physical properties in epoxy-acrylate hybrid resins. In order to increase the epoxide conversion and rate of polymerization, the sensitivity of epoxides to alcohol is used to facilitate the activated monomer (AM) mechanism and induce a covalent bond between the epoxide and acrylate polymers through the hydroxyl group. It is hypothesized that if the AM mechanism is facilitated, epoxide conversion will increase. As a result, the resins can be tailored to control phase separation and physical properties, and shrinkage stress can be reduced. In pursuit of these objectives, the hybrid monomer METHB was polymerized at temperatures ranging from 30°C to 70°C to obtain apparent activation

  10. Advances in acrylic-alkyd hybrid synthesis and characterization

    Science.gov (United States)

    Dziczkowski, Jamie

    2008-10-01

    In situ graft acrylic-alkyd hybrid resins were formed by polymerizing acrylic and acrylic-mixed monomers in the presence of alkyds by introduction of a free radical initiator to promote graft formation. Two-dimensional NMR, specifically gradient heteronuclear multiple quantum coherence (gHMQC), was used to clarify specific graft sites of the hybrid materials. Both individual and mixed-monomer systems were produced to determine any individual monomer preferences and to model current acrylic-alkyd systems. Different classes of initiators were used to determine any initiator effects on graft location. The 2D-NMR results confirm grafting at doubly allylic hydrogens located on the fatty acid chains and the polyol segment of the alkyd backbone. The gHMQC spectra show no evidence of grafting across double bonds on either pendant fatty acid groups or THPA unsaturation sites for any of the monomer or mixed monomer systems. It was also determined that choice of initiator has no effect on graft location. In addition, a design of experiments using response surface methodology was utilized to obtain a better understanding of this commercially available class of materials and relate both the chemical and physical properties to one another. A Box-Behnkin design was used, varying the oil length of the alkyd phase, the degree of unsaturation in the polyester backbone, and acrylic to alkyd ratio. Acrylic-alkyd hybrid resins were reduced with an amine/water mixture. Hydrolytic stability was tested and viscoelastic properties were obtained to determine crosslink density. Cured films were prepared and basic coatings properties were evaluated. It was found that the oil length of the alkyd is the most dominant factor for final coatings properties of the resins. Acrylic to alkyd ratio mainly influences the resin properties such as acid number, average molecular weight, and hydrolytic stability. The degree of unsaturation in the alkyd backbone has minimal effects on resin and film

  11. Poly(lauryl acrylate) and poly(stearyl acrylate) grafted multiwalled carbon nanotubes for polypropylene composites

    DEFF Research Database (Denmark)

    Daugaard, Anders Egede; Jankova Atanasova, Katja; Hvilsted, Søren

    2014-01-01

    Two new polymer grafts on an industrial grade multiwalled carbon nanotube (MWCNT) were prepared through a non-oxidative pathway employing controlled free radical polymerization for surface initiated polymer grafting. After photochemical introduction of an ATRP initiator onto the MWCNT, polymeriza......Two new polymer grafts on an industrial grade multiwalled carbon nanotube (MWCNT) were prepared through a non-oxidative pathway employing controlled free radical polymerization for surface initiated polymer grafting. After photochemical introduction of an ATRP initiator onto the MWCNT...... to be substantially improved, where poly(lauryl acrylate) was found to be the superior surface modification, resulting in a conductive composite....

  12. Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

    OpenAIRE

    Keslarek Amauri José; Leite Carlos Alberto P; Galembeck Fernando

    2004-01-01

    Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM). Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the par...

  13. Fracture properties of an acrylic bone cement.

    Science.gov (United States)

    Bialoblocka-Juszczyk, E; Baleani, M; Cristofolini, L; Viceconti, M

    2008-01-01

    This study investigated experimentally the fracture properties, i.e., the fatigue strength, the resistance to crack propagation and the fracture toughness, of an acrylic bone cement (Cemex RX). The mean endurance limit was determined following the staircase method. The endurance limit was estimated at 9.2 MPa. The fatigue crack propagation rate was measured according to the ASTM E647 standard. The equation of the line fitting the crack growth per cycle (da/dN) versus the stress-intensity factor range (delta K), in a log-log graph, was used to calculate the empirical constants of Paris' law for the selected bone cement: da/dN (m/cycle) = 3.56 x 10(-7) x delta K (MPa x m1/2)5.79. This power-law relationship described well (R2 = 0.96) the growth rate in the stable crack growth region, i.e., in the mid delta K range. The fracture toughness K(IC) of the bone cement was determined according to the ASTM E399 standard. The K(IC) mean value was 1.38 MPa x m1/2. These experimental results provide the set of necessary inputs for numerical studies aimed to investigate the damage accumulation process in the mantle fixing cemented prostheses.

  14. Coating materials and solvents. 2. Acrylic acid, acrylate, and MMA; Toryo yozai. 2. Akurirusan oyobi akurirusan esuteru MMA

    Energy Technology Data Exchange (ETDEWEB)

    Akazawa, Y. [Nippon Shokubai Co. Ltd., Osaka (Japan)

    1997-09-01

    This paper describes the production process, its scale, physical properties and usage of acrylic acid, acrylate for general use, and MMA (methyl methacrylate). The propylene oxidation process is only one process for the industrial production of acrylic acid and acrylate due to its economical predominance. Annual production of acrylic acid in the world has reached to about 2.2 million tons. Relatively high growth rate is forecasted also in the future. In Japan, the acrylate is used for paints, adhesive materials, and fibers. The industrial production process of MMA includes ACH (acetone cyanhydrin) process, new ACH process, isobutylene process, MAN (methacrylonitrile) process, and ethylene carbonylation process. Demand and supply of MMA are characterized especially by the high proportion of export from Japan to the Asian region. Methacrylic resins are used for various materials, such as tail lamp lenses and meter panels of automobiles, and laser disks, CD-ROM and MD pick-ups in the field of electronic industry. Consumption of these resins is steadily extended. 16 refs., 6 figs., 7 tabs.

  15. Clinical Aspects of Combination of Ceramic and Acrylic Occlusal Surfaces

    Directory of Open Access Journals (Sweden)

    Z. Ozhohan

    2017-03-01

    Full Text Available The objective of the research was to develop and substantiate the methods of constructing the occlusal surfaces when manufacturing aesthetic fixed restorations through the combination of different materials. Materials and methods. The study included 65 patients with ceramic and acrylic occlusal surfaces of aesthetic fixed dental prostheses. Group I included 21 patients with a combination of ceramic and acrylic occlusal surfaces. Group II included 22 patients with a combination of ceramic occlusal surfaces. Group III included 22 patients with a combination of acrylic occlusal surfaces. The patients were observed 3, 6 and 12 months after prosthetic repair. Results. The greatest increase in the occlusal contact surface area of fixed restorations was observed in Group I, that is, when combining dental prostheses with ceramic and acrylic occlusal surfaces. Considering uneven abrasion of the occlusal surfaces, we do not recommend to combine different materials when veneering the occlusal surface of the antagonistic teeth. Conclusions. This study demonstrated the important role of the correct combination of materials when veneering the occlusal surfaces. Physical and chemical properties of materials, namely the abrasion resistance play a significant role in the long-term denture functioning. The smallest increase in the occlusal contact surface area was observed in Group II when combining ceramic occlusal surfaces. It was due to a good abrasion resistance of ceramics as compared to acrylic resin as well as the presence of the glazed layer which prevents the premature abrasion of the occlusal surfaces of the antagonistic teeth due to lower surface roughness. The combination of acrylic resin and ceramics when constructing the occlusal surfaces of fixed restorations in Group I demonstrated the highest rate of the increase in the occlusal contact surface area – 9.93%. It was due to a low hardness of acrylic resin and its high surface roughness. In

  16. Large deformation micromechanics of particle filled acrylics at elevated temperatures

    Science.gov (United States)

    Gunel, Eray Mustafa

    The main aim of this study is to investigate stress whitening and associated micro-deformation mechanism in thermoformed particle filled acrylic sheets. For stress whitening quantification, a new index was developed based on image histograms in logarithmic scale of gray level. Stress whitening levels in thermoformed acrylic composites was observed to increase with increasing deformation limit, decreasing forming rate and increasing forming temperatures below glass transition. Decrease in stress whitening levels above glass transition with increasing forming temperature was attributed to change in micro-deformation behavior. Surface deformation feature investigated with scanning electron microscopy showed that source of stress whitening in thermoformed samples was a combination of particle failure and particle disintegration depending on forming rate and temperature. Stress whitening level was strongly correlated to intensity of micro-deformation features. On the other hand, thermoformed neat acrylics displayed no surface discoloration which was attributed to absence of micro-void formation on the surface of neat acrylics. Experimental damage measures (degradation in initial, secant, unloading modulus and strain energy density) have been inadequate in describing damage evolution in successive thermoforming applications on the same sample at different levels of deformation. An improved version of dual-mechanism viscoplastic material model was proposed to predict thermomechanical behavior of neat acrylics under non-isothermal conditions. Simulation results and experimental results were in good agreement and failure of neat acrylics under non-isothermal conditions ar low forming temperatures were succesfully predicted based on entropic damage model. Particle and interphase failure observed in acrylic composites was studied in a multi-particle unit cell model with different volume fractions. Damage evolution due to particle failure and interphase failure was simulated

  17. Occupational asthma due to acrylates in a graphic arts worker.

    Science.gov (United States)

    Reig Rincón de Arellano, I; Cimarra Alvarez-Lovell, M; Robledo Echarren, T; Fernández-Nieto, M; Quirce Gancedo, S; Seaone Plata, C; Martínez-Cócera, C

    2006-01-01

    Acrylates are used in a wide variety of products such as solvents, adhesives, paints, printing ink, soft contact lenses, porcelain nails, and methacrylates (used by dentists and orthopedists). Currently there are various types of acrylic compounds: acrylates, cyanoacrylates (such as tissue adhesives and home glues), and methacrylates (prostheses and dental and orthopedic fillings). The sensitization mechanism is unknown, but the allergy is believed to be due to a non-IgE mediated phenomenon, since a late asthmatic response occurs. Various cases of acrylate-induced asthma have been reported, especially in dentists and persons using glues or paints containing this substance. We present the case of a 52-year-old man who had been working in graphic arts for the previous 7 years. For the previous 2 years he had experienced persistent cough with a sensation of drowning, dyspnea that increased with moderate exertion, and nasal obstruction despite continuous treatment. The symptoms first appeared after an episode of acute respiratory difficulty associated with weight loss, pulmonary infiltrates, and eosinophilia. Peak expiratory flow (PEF) was measured during work and sick leave, and specific bronchial challenge with acrylates was performed in a bronchial chamber. The PEF improved on weekends and sick leave. The challenge test provoked a late asthmatic response and the non-specific bronchial hyperreactivity increased after the test. As well in the sputum samples there was a increase of eosinophil amount.

  18. Allergic contact stomatitis caused by acrylic monomer in a denture.

    Science.gov (United States)

    Koutis, D; Freeman, S

    2001-08-01

    A 71-year-old edentulous man developed a severely painful red mouth at sites of contact with a new denture. Patch testing showed allergy to samples of the denture material and to 2-hydroxyethyl methacrylate. Patch testing to methyl methacrylate was negative. Prolonged boiling of the denture resulted in reversal of his symptoms and samples of this fully cured denture material produced negative patch tests. While allergy to acrylates is a rare cause of stomatitis, this possibility must be considered in patients presenting with oral symptoms. Material safety data sheets are unreliable in providing information regarding the type of acrylate present in the material. Hence, patch testing should be performed with a battery of acrylate allergens as well as with small samples of the denture material.

  19. Preparation and Characterization of Acrylic Primer for Concrete Substrate Application

    Directory of Open Access Journals (Sweden)

    El-Sayed Negim

    2016-01-01

    Full Text Available This study dealt with the properties of acrylic primer for concrete substrate using acrylic syrup, made from a methyl methacrylate monomer solution of terpolymers. Terpolymer systems consisting of methyl methacrylate (MMA, 2-ethylhexyl acrylate (2-EHA, and methacrylic acid (MAA with different chemical composition ratios of MMA and 2-EHA were synthesized through bulk polymerization using azobisisobutyronitrile (AIBN as initiator. The terpolymer composition is characterized by FTIR, 1H NMR, DSC, TGA, and SEM. The glass transition temperature and the thermal stability increased with increasing amounts of MMA in the terpolymer backbone. The effect of chemical composition of terpolymers on physicomechanical properties of primer films was investigated. However, increasing the amount of MMA in terpolymer backbone increased tensile and contact angle of primer films while elongation at break, water absorption, and bond strength are decreased. In particular, the primer syrup containing 65% 2-EHA has good bonding strength with concrete substrate around 1.1 MPa.

  20. Lightweight bonded acrylic facing at the Vitra VSL Factory

    Directory of Open Access Journals (Sweden)

    Matthias Michel

    2013-12-01

    Full Text Available Acrylic glass is omnipresent in the industrialised world; but as a building material most architects, facade planners and engineers are still unfamiliar with this material. In most cases it is applied as a substitute for glass which leads to inappropriate joints and fixtures. During the years of the path toward the digital era, the authors were in the fortunate position to be involved in several unconventional glass and acrylic glass projects.On the basis of their most recent project, the  facade of the Vitra VSL Factory by SANAA Architekten, they describe the development of a facade for which they chose acrylic glass not as a substitute for glass but rather as a conscious material choice. Since the entire facade is it was possible to apply the manufacturing technology of deep-drawing, allowing for very thin wall thicknesses.

  1. Lightweight bonded acrylic facing at the Vitra VSL Factory

    Directory of Open Access Journals (Sweden)

    Matthias

    2013-12-01

    Full Text Available Corresponding author: Matthias Michel, E-mail: michel@imagine-structure.eu Acrylic glass is omnipresent in the industrialised world; but as a building material most architects, facade planners and engineers are still unfamiliar with this material. In most cases it is applied as a substitute for glass which leads to inappropriate joints and fixtures. During the years of the path toward the digital era, the authors were in the fortunate position to be involved in several unconventional glass and acrylic glass projects. On the basis of their most recent project, the facade of the Vitra VSL Factory by SANAA Architekten, they describe the development of a facade for which they chose acrylic glass not as a substitute for glass but rather as a conscious material choice. Since the entire facade is it was possible to apply the manufacturing technology of deep-drawing, allowing for very thin wall thicknesses.

  2. Nucleophilic Addition of Reactive Dyes on Amidoximated Acrylic Fabrics

    Science.gov (United States)

    El-Shishtawy, Reda M.; El-Zawahry, Manal M.; Abdelghaffar, Fatma; Ahmed, Nahed S. E.

    2014-01-01

    Seven reactive dyes judiciously selected based on chemical structures and fixation mechanisms were applied at 2% owf of shade on amidoximated acrylic fabrics. Amidoximated acrylic fabric has been obtained by a viable amidoximation process. The dyeability of these fabrics was evaluated with respect to the dye exhaustion, fixation, and colour strength under different conditions of temperature and dyeing time. Nucleophilic addition type reactive dyes show higher colour data compared to nucleophilic substitution ones. FTIR studies further implicate the binding of reactive dyes on these fabrics. A tentative mechanism is proposed to rationalize the high fixation yield obtained using nucleophilic addition type reactive dyes. Also, the levelling and fastness properties were evaluated for all dyes used. Excellent to good fastness and levelling properties were obtained for all samples irrespective of the dye used. The result of investigation offers a new method for a viable reactive dyeing of amidoximated acrylic fabrics. PMID:25258720

  3. Nucleophilic addition of reactive dyes on amidoximated acrylic fabrics.

    Science.gov (United States)

    El-Shishtawy, Reda M; El-Zawahry, Manal M; Abdelghaffar, Fatma; Ahmed, Nahed S E

    2014-01-01

    Seven reactive dyes judiciously selected based on chemical structures and fixation mechanisms were applied at 2% of of shade on amidoximated acrylic fabrics. Amidoximated acrylic fabric has been obtained by a viable amidoximation process. The dyeability of these fabrics was evaluated with respect to the dye exhaustion, fixation, and colour strength under different conditions of temperature and dyeing time. Nucleophilic addition type reactive dyes show higher colour data compared to nucleophilic substitution ones. FTIR studies further implicate the binding of reactive dyes on these fabrics. A tentative mechanism is proposed to rationalize the high fixation yield obtained using nucleophilic addition type reactive dyes. Also, the levelling and fastness properties were evaluated for all dyes used. Excellent to good fastness and levelling properties were obtained for all samples irrespective of the dye used. The result of investigation offers a new method for a viable reactive dyeing of amidoximated acrylic fabrics.

  4. Clinical properties of a novel, glistening-free, single-piece, hydrophobic acrylic IOL

    Directory of Open Access Journals (Sweden)

    Packer M

    2014-02-01

    Full Text Available Mark Packer,1 Mohan Rajan,2 Edoardo Ligabue,3 Peter Heiner4 1Oregon Health and Science University, Portland, OR, USA; 2Rajan Eye Care Hospital Pvt Ltd, Chennai, India; 3Ophthalmology Department, Centro Diagnostico Italiano, Milan, Italy; 4Bond University Medical School, Robina, QLD, Australia Abstract: A new, single-piece, hydrophobic acrylic lens – the first constructed with a lens optic and haptics comprised of a hydroxyethyl methacrylate-polyethylene glycol phenyl ether acrylate–styrene copolymer, cross-linked with ethylene glycol dimethacrylate, and labeled as "glistening-free" – was recently introduced globally. Glistenings have been a significant source of clinical concern with previous hydrophobic lens designs. This new monofocal lens provides enhanced, clear optics for lens-based surgery. The superior optical clarity of this lens is achieved through the elimination of glistenings, enhanced surface durability, high refractive index, a high Abbe number, and an aspheric design. Additionally, the lens design reduces the risk of developing posterior capsule opacification. Keywords: glistenings, monofocal hydrophobic acrylic, IOL, aspheric

  5. Biosynthetic pathway for acrylic acid from glycerol in recombinant Escherichia coli.

    Science.gov (United States)

    Tong, Wenhua; Xu, Ying; Xian, Mo; Niu, Wei; Guo, Jiantao; Liu, Huizhou; Zhao, Guang

    2016-06-01

    Acrylic acid is an important industrial feedstock. In this study, a de novo acrylate biosynthetic pathway from inexpensive carbon source glycerol was constructed in Escherichia coli. The acrylic acid was produced from glycerol via 3-hydroxypropionaldehyde, 3-hydroxypropionyl-CoA, and acrylyl-CoA. The acrylate production was improved by screening and site-directed mutagenesis of key enzyme enoyl-CoA hydratase and chromosomal integration of some exogenous genes. Finally, our recombinant strain produced 37.7 mg/L acrylic acid under shaking flask conditions. Although the acrylate production is low, our study shows feasibility of engineering an acrylate biosynthetic pathway from inexpensive carbon source. Furthermore, the reasons for limited acrylate production and further strain optimization that should be performed in the future were also discussed.

  6. Elastic modulus and flexural strength comparisons of high-impact and traditional denture base acrylic resins

    Directory of Open Access Journals (Sweden)

    Nour M. Ajaj-ALKordy

    2014-01-01

    Conclusion: Within the limitations of this study, it can be concluded that the high-impact acrylic resin is a suitable denture base material for patients with clinical fracture of the acrylic denture.

  7. Microwave preservation method for DMSP, DMSO, and acrylate in unfiltered seawater and phytoplankton culture samples

    National Research Council Canada - National Science Library

    Kinsey, Joanna D; Kieber, David J

    2016-01-01

    ... T ), dimethylsulfoxide (DMSO T ), and acrylate (acrylate T ) concentrations in unfiltered samples to alleviate problems associated with the acidification method when applied to samples containing Phaeocystis . Microwave‐ and acid...

  8. RAFT-Mediated Polymerization-Induced Self-Assembly of Poly(Acrylic Acid-b-Poly(Hexafluorobutyl Acrylate: Effect of the pH on the Synthesis of Self-Stabilized Particles

    Directory of Open Access Journals (Sweden)

    Jianhua Zhou

    2016-05-01

    Full Text Available This paper describes a very simple strategy towards self-stabilized poly(acrylic acid-block-poly(hexafluorobutyl acrylate (PAA-b-PHFBA block copolymer particles via reversible addition-fragmentation chain transfer (RAFT-mediated polymerization-induced self-assembly. Hexafluorobutyl acrylate (HFBA monomer conversion and number-average molar mass of PAA-b-PHFBA increased gradually with the increase in the pH value of the aqueous phase. When pH < 10, the molecular weight distributions of PAA-b-PHFBA were narrow, however, when the pH was raised to 11.55, PAA-b-PHFBA block copolymers had a broader distribution (ĐM = 1.82 with a serious trailing toward the low molecular weight. Furthermore, the morphology and size of PAA-b-PHFBA latex particles were measured by transmission electron microscopy and dynamic light scattering. The results indicated that the PAA-b-PHFBA latex particles had a clear spherical core-shell structure and the latex particles’ size increased with the increase of pH value.

  9. Technology and the use of acrylics for provisional dentine protection.

    Science.gov (United States)

    Kapusevska, Biljana; Dereban, Nikola; Popovska, Mirjana; Nikolovska, Julijana; Radojkova Nikolovska, Vеrа; Zabokova Bilbilova, Efka; Mijoska, Aneta

    2013-01-01

    Acrylics are compounds polymerized from monomers of acrylic, metacrylic acid or acrylonitrates. The purpose of this paper is to present the technology and use of acrylics for provisional dentine protection in the practice of dental prosthodontics. For this reason, we followed 120 clinical cases from the everyday clinical practice, divided into 4 groups of 30 patients who needed prosthetic reconstruction. The first group included cases in which we applied celluloid crowns for dentine protection, for the second group we used acrylic teeth from a set of teeth for complete dentures; in the third and fourth groups the fabrication was done with the system of an impression matrix and the acrylic resin block technique respectively. In all the examined patients, the gingival index by Silness and Loe and the vitality of the dental pulp were verified clinically, after preparation and 8 days from the placement of the provisional crown. The value for dental sensitivity measured after preparation was 2.59, and 8 days after the placement of the provisional crown it bwas 3.1. From these results we can conclude that after the 8th day from the placement of the provisional crown, there was an adaptation period, characterized by a decrease in the painful sensations. The value of the Silness and Loe gingival index measured after the preparation was 1.34, and 8 days from the placement of the provisional crown was 0.94. The results inclined us to the fact that the provisional acrylic crowns facilitated the reparation of the periodontal tissue.

  10. Improving water sensitivity in acrylic films using surfmers.

    Science.gov (United States)

    Aramendia, Esteban; Barandiaran, María J; Grade, Joe; Blease, Trevor; Asua, José M

    2005-02-15

    The water sensitivity of films obtained from high solids content acrylic latexes was investigated, with special focus on the role of the surfactant used in the synthesis step. The performance of films obtained from latexes stabilized by nonionic surfmers was compared to that of the acrylic latexes stabilized with conventional nonionic and anionic surfactants. It was seen that the latexes stabilized with reactive surfactants exhibited a remarkably better resistance to both water permeability and water vapor permeability and therefore enlarged the durability of the films. Atomic force microscopy images suggested that the defects created by surfactant migration in the latexes stabilized with conventional surfactants promoted the permeation of water by capillarity.

  11. The creep behavior of acrylic denture base resins.

    Science.gov (United States)

    Sadiku, E R; Biotidara, F O

    1996-01-01

    The creep behavior of acrylic dental base resins, at room temperature and at different loading conditions, has been examined. The behaviors of these resins are similar to that of "commercial perspex" at room temperature over a period of 1000 seconds. The pseudo-elastic moduli of the blends of PMMA VC show a significant increase compared with PMMA alone. The addition of the PVC powder to the heat-cured acrylic resin increased the time-dependent elastic modulus. This increase in elastic modulus is advantageous in the production of denture based resins of improv mechanical properties.

  12. Immunogenicity of acrylate chemicals as assessed by antibody induction.

    Science.gov (United States)

    Bull, J E; Henderson, D C; Turk, J L

    1987-01-01

    The immunogenicities of two acrylate chemicals, trimethylolpropane triacrylate (TMPTA) and methyl acrylate (MeAc), and one related vinyl compound, 4-vinyl pyridine (4VP), were investigated by determining the in vivo induction of IgG antibodies in guinea pigs. The injection of the chemicals emulsified in Freund's complete adjuvant resulted in the induction of serum antibody responses against MeAc and 4VP but not TMPTA. However, antibody with anti-TMPTA activity was produced following immunization of guinea pigs with TMPTA conjugated to protein, which allowed comparisons to be made of the immunogenic structural features of the compounds.

  13. Effects of Novel Structure Bonding Materials on Properties of Aeronautical Acrylic

    OpenAIRE

    Li, Zhisheng; Zhang, Hongfeng; Li, Lei; Yan, Yue

    2017-01-01

    Novel structure bonding materials, J-351 epoxy adhesive film with low curing temperature and liquid modified acrylate SY-50s adhesive were chosen and characterized. The effects of adhesives on the mechanical properties of acrylic were studied. The results reveal that both adhesives have excellent bonding properties to acrylic. The stress-solvent crazing value of J-351 is higher than that of SY-50s. With the application of adhesive on the surface, mechanical properties of acrylic are declined....

  14. Novel azo-peresters radical initiators used for the synthesis of acrylic pressure-sensitive adhesives

    Directory of Open Access Journals (Sweden)

    2008-04-01

    Full Text Available Acrylic pressure-sensitive adhesives (PSA based on two monomers: 2-ethylhexyl acrylate and acrylic acid were synthesized in organic solvent ethyl acetate using AIBN (2, 2'-azo-diisobutyronitrile and new synthesized azo-peresters as radical initiators. After polymerization the viscosity, molecular weight and polydispersity of synthesized acrylic PSA were evaluated. The novel synthesized radical azo-perester initiators were synthesized, isolated and compared with industrial predominant usable azo-initiator AIBN.

  15. 40 CFR 721.10192 - Amides, coco, N-[3-(dibutylamino)propyl], acrylates.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amides, coco, N- , acrylates. 721... Substances § 721.10192 Amides, coco, N- , acrylates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as amides, coco, N- , acrylates (PMN P-06-263...

  16. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane...

  17. 76 FR 77709 - Butyl acrylate-methacrylic acid-styrene polymer; Tolerance Exemption

    Science.gov (United States)

    2011-12-14

    ... AGENCY 40 CFR Part 180 Butyl acrylate-methacrylic acid-styrene polymer; Tolerance Exemption AGENCY...-propenoate and ethenylbenzene (CAS Reg. No. 25036-16-2); also known as butyl acrylate-methacrylic acid...-risk polymers are described in 40 CFR 723.250(d). Butyl acrylate-methacrylic acid-styrene polymer...

  18. 40 CFR 721.10101 - Copolymer of alkyl acrylate and ethyleneglycol dimethacrylate (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Copolymer of alkyl acrylate and... Significant New Uses for Specific Chemical Substances § 721.10101 Copolymer of alkyl acrylate and...) The chemical substance identified generically as copolymer of alkyl acrylate and ethyleneglycol...

  19. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-methyl acrylate copolymer resins. 177.1340... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1340 Ethylene-methyl acrylate copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used as articles or components of...

  20. 40 CFR 180.1162 - Acrylate polymers and copolymers; exemption from the requirement of a tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Acrylate polymers and copolymers... RESIDUES IN FOOD Exemptions From Tolerances § 180.1162 Acrylate polymers and copolymers; exemption from the requirement of a tolerance. (a) Acrylate polymers and copolymers are exempt from the requirement of a...

  1. CROSS-REACTION PATTERNS IN GUINEA-PIGS SENSITIZED TO ACRYLIC-MONOMERS

    DEFF Research Database (Denmark)

    Clemmensen, S.

    1984-01-01

    The cross-reaction patterns of selected acrylate and methacrylate esters were investigated using the guinea pig maximization test. Methacrylates were less potent sensitizers than acrylates. Cross-sensitization was found between (meth)acrylates with closely related core structures, most extensivel...

  2. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting under...

  3. 40 CFR 721.10147 - Acrylate derivative of alkoxysilylalkane ester and mixed metal oxides (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate derivative of... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10147 Acrylate derivative of... reporting. (1) The chemical substance identified generically as acrylate derivative of alkoxysilylalkane...

  4. Tuning of thermally induced sol-to-gel transitions of moderately concentrated aqueous solutions of doubly thermosensitive hydrophilic diblock copolymers poly(methoxytri(ethylene glycol) acrylate)-b-poly(ethoxydi(ethylene glycol) acrylate-co-acrylic acid).

    Science.gov (United States)

    Jin, Naixiong; Zhang, Hao; Jin, Shi; Dadmun, Mark D; Zhao, Bin

    2012-03-15

    We report in this article a method to tune the sol-to-gel transitions of moderately concentrated aqueous solutions of doubly thermosensitive hydrophilic diblock copolymers that consist of two blocks exhibiting distinct lower critical solution temperatures (LCSTs) in water. A small amount of weak acid groups is statistically incorporated into the lower LCST block so that its LCST can be tuned by varying solution pH. Well-defined diblock copolymers, poly(methoxytri(ethylene glycol) acrylate)-b-poly(ethoxydi(ethylene glycol) acrylate-co-acrylic acid) (PTEGMA-b-P(DEGEA-co-AA)), were prepared by reversible addition-fragmentation chain transfer polymerization and postpolymerization modification. PTEGMA and PDEGEA are thermosensitive water-soluble polymers with LCSTs of 58 and 9 °C, respectively, in water. A 25 wt % aqueous solution of PTEGMA-b-P(DEGEA-co-AA) with a molar ratio of DEGEA to AA units of 100:5.2 at pH = 3.24 underwent multiple phase transitions upon heating, from a clear, free-flowing liquid (<15 °C) to a clear, free-standing gel (15-46 °C) to a clear, free-flowing hot liquid (47-56 °C), and a cloudy mixture (≥57 °C). With the increase of pH, the sol-to-gel transition temperature (T(sol-gel)) shifted to higher values, while the gel-to-sol transition (T(gel-sol)) and the clouding temperature (T(clouding)) of the sample remained essentially the same. These transitions and the tunability of T(sol-gel) originated from the thermosensitive properties of two blocks of the diblock copolymer and the pH dependence of the LCST of P(DEGEA-co-AA), which were confirmed by dynamic light scattering and differential scanning calorimetry studies. Using the vial inversion test method, we mapped out the C-shaped sol-gel phase diagrams of the diblock copolymer in aqueous buffers in the moderate concentration range at three different pH values (3.24, 5.58, and 5.82, all measured at ~0 °C). While the upper temperature boundaries overlapped, the lower temperature boundary

  5. Acrylic Triblock Copolymers Incorporating Isosorbide for Pressure Sensitive Adhesives

    Energy Technology Data Exchange (ETDEWEB)

    Gallagher, James J.; Hillmyer, Marc A.; Reineke, Theresa M. (UMM)

    2016-05-10

    A new monomer acetylated acrylic isosorbide (AAI) was prepared in two steps using common reagents without the need for column chromatography. Free radical polymerization of AAI afforded poly(acetylated acrylic isosorbide) (PAAI), which exhibited a glass transition temperature (Tg) = 95 °C and good thermal stability (Td, 5% weight loss; N2 = 331 °C, air = 291 °C). A series of ABA triblock copolymers with either poly(n-butyl acrylate) (PnBA) or poly(2-ethylhexyl acrylate) (PEHA) as the low Tg midblocks and PAAI as the high Tg end blocks were prepared using Reversible Addition–Fragmentation chain Transfer (RAFT) polymerization. The triblock copolymers ranging from 8–24 wt % PAAI were evaluated as pressure sensitive adhesives by 180° peel, loop tack, and static shear testing. While the PAAI-PEHA-PAAI series exhibited poor adhesive qualities, the PAAI-PnBA-PAAI series of triblock copolymers demonstrated peel forces up to 2.9 N cm–1, tack forces up to 3.2 N cm–1, and no shear failure up to 10000 min. Dynamic mechanical analysis indicated that PAAI-PEHA-PAAI lacked the dissipative qualities needed to form an adhesive bond with the substrate, while the PAAI-PnBA-PAAI series exhibited a dynamic mechanical response consistent with related high performing PSAs.

  6. In-situ photopolymerization of oriented liquid-crystalline acrylates

    NARCIS (Netherlands)

    Broer, Dirk Jan

    1990-01-01

    The scope of this thesis concerns a new method to produce oriented polymers by the in-situ photopolymerization of oriented liquid-crystalline acrylates. The desired macroscopic molecular order is already accomplished in the monomeric state prior to the polymerization. ... Zie: Summary

  7. Hydrogen Bonding Interaction between 1-Propanol and Acrylic ...

    African Journals Online (AJOL)

    The association between 1-propanol and acrylic esters (methyl methacrylate, ethyl methacrylate and butyl methacrylate) in non-polar solvents, viz. n-heptane, CCl4, and benzene has been investigated by means of FTIR spectroscopy. The formation constants of the 1:1 complexes have been calculated using Nash's method.

  8. Comparison of classical dermatoscopy and acrylic globe magnifier dermatoscopy

    DEFF Research Database (Denmark)

    Lorentzen, Henrik F; Eefsen, Rikke Løvendahl; Weismann, Kaare

    2008-01-01

    % confidence interval 83-97%). Sensitivity for melanoma, benign melanocytic naevi and basal cell carcinoma was 100%, 98% and 85%, respectively. Specificity was 95%, 94% and 100% for melanoma, naevi and basal cell carcinoma. Acrylic globe dermatoscopy enables a diagnostic accuracy similar to epiluminescence...

  9. SYNTHESIS OF ACRYLIC ESTERS IN PTC: KINETICS AND ECOLOGICAL ASPECTS

    Directory of Open Access Journals (Sweden)

    G.Torosyan

    2013-06-01

    Full Text Available The synthesis of esters of acrylic acids, which are applied for synthesis of polymeric materials by phase transfer catalysis were discussed (PTC, which is very useful for reduction of reaction consumption of materials and power.This method has substantial advantages including high speed of the process, soft condition of reaction and reduced pollution.

  10. Decarboxylation-based traceless linking with aroyl acrylic acids

    DEFF Research Database (Denmark)

    Nielsen, John

    1998-01-01

    beta-Keto carboxylic acids are known to decarboxylate readily. In our pursuit to synthesize beta-indolinyl propiophenones, we have exploited this chemistry as a mean of establishing a traceless handle. 2-Aroyl acrylic acids have been esterified to a trityl resin, after which Michael-type addition...

  11. Lightweight bonded acrylic facing at the Vitra VSL Factory

    NARCIS (Netherlands)

    Michel, M.T.; Techen, H.

    2013-01-01

    Acrylic glass is omnipresent in the industrialised world; but as a building material most architects, facade planners and engineers are still unfamiliar with this material. In most cases it is applied as a substitute for glass which leads to inappropriate joints and fixtures. During the years of the

  12. Investigation into nanocellulosics versus acacia reinforced acrylic films

    Science.gov (United States)

    Yunqiao Pu; Jianguo Zhang; Thomas Elder; Yulin Deng; Paul Gatenholm; Arthur J. Ragauskas

    2007-01-01

    Three closely related cellulosic acrylic latex films were prepared employing acacia pulp fibers, cellulose whiskers and nonocellulose balls and their respective strength properties were determined. Cellulose whisker reinforced composites had enhanced strength properties compared to the acacia pulp and nanoball composites. AFM analysis indicated that the cellulose...

  13. Effect of acrylic acid on the properties of polyvinylpyrrolidone ...

    African Journals Online (AJOL)

    Hydrogels based on polyvinylpyrrolidone (PVP) networks grafted with acrylic acid (AAc) was prepared by using γ-rays from a Co-60 source at room temperature. The parameters like effect of radiation dose and concentration of AAc were studied. The properties such as gel content, swelling behavior and thermal stability ...

  14. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Science.gov (United States)

    2010-07-01

    ...). 721.324 Section 721.324 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC... subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate polymer... A of this part apply to this section except as modified by this paragraph. (1) Recordkeeping...

  15. 40 CFR 721.330 - Aromatic acrylate (generic).

    Science.gov (United States)

    2010-07-01

    ... Section 721.330 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES... reporting. (1) The chemical substance identified generically as an aromatic acrylate (PMN P-01-420) is... this section except as modified by this paragraph. (1) Recordkeeping. Recordkeeping requirements as...

  16. Gingival Tissue Color Related With Facial Skin and Acrylic Resin ...

    African Journals Online (AJOL)

    Research into the degree of epithelial vascularisation, keratinisation and melanin pigmentation of the various zones in the mouth in this environment is required which may explain the reason for the dark colour observed in the attached gingival. Key Word: Gingival tissue colour, denture, skin, acrylic resin, Nigerians ...

  17. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate ester copolymer coating. 175.210 Section 175.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: ADHESIVES AND COMPONENTS OF COATINGS Substances for Use as Components of Coatings...

  18. Bond strength between acrylic resin and maxillofacial silicone

    Science.gov (United States)

    HADDAD, Marcela Filié; GOIATO, Marcelo Coelho; dos SANTOS, Daniela Micheline; CREPALDI, Nádia de Marchi; PESQUEIRA, Aldiéris Alves; BANNWART, Lisiane Cristina

    2012-01-01

    The development of implant dentistry improved the possibilities of rehabilitation with maxillofacial prosthesis. However, clinically it is difficult to bond the silicone to the attachment system. Objectives This study aimed to evaluate the effect of an adhesive system on the bond strength between acrylic resin and facial silicone. Material and Methods A total of 120 samples were fabricated with auto-polymerized acrylic resin and MDX 4-4210 facial silicone. Both materials were bonded through mechanical retentions and/or application of primers (DC 1205 primer and Sofreliner primer S) and adhesive (Silastic Medical Adhesive Type A) or not (control group). Samples were divided into 12 groups according to the method used to attach the silicone to the acrylic resin. All samples were subjected to a T-peel test in a universal testing machine. Failures were classified as adhesive, cohesive or mixed. The data were evaluated by the analysis of variance (ANOVA) and the Tukey's HSD test (α=.05). Results The highest bond strength values (5.95 N/mm; 3.07 N/mm; 4.75 N/mm) were recorded for the samples that received a Sofreliner primer application. These values were significantly higher when the samples had no scratches and did not receive the application of Silastic Medical Adhesive Type A. Conclusions The most common type of failure was adhesive. The use of Sofreliner primer increased the bond strength between the auto-polymerized acrylic resin and the Silastic MDX 4-4210 facial silicone. PMID:23329247

  19. Oil-acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, van E.M.S.; Es, van J.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  20. Simultaneous production of biobased styrene and acrylates using ethenolysis

    NARCIS (Netherlands)

    Spekreijse, J.; Notre, le J.E.L.; Haveren, van J.; Scott, E.L.; Sanders, J.P.M.

    2012-01-01

    Phenylalanine (1), which could be potentially obtained from biofuel waste streams, is a precursor of cinnamic acid (2) that can be converted into two bulk chemicals, styrene (3) and acrylic acid (4), via an atom efficient pathway. With 5 mol% of Hoveyda–Grubbs 2nd generation catalyst, 1 bar of

  1. Studies on thin film materials on acrylics for optical applications

    Indian Academy of Sciences (India)

    Unknown

    Films are also coated on plastics to protect the surfaces against abrasion and moisture penetration. Deposition of thin film coatings on acrylics is a challenging job because they are soft, temperature sensitive, moisture absorbing and desorb in vacuum. Moreover, there is a large gap between thermal expansion coefficient of ...

  2. Performance of waterborne acrylic surface coatings on wood ...

    Indian Academy of Sciences (India)

    Two waterborne acrylic coatings were applied on spruce wood, impregnated with two copperethanolamine containing preservatives (CuE and CuEQ), one of them (CuEQ) containing a boron compound, octanoic acid and a quaternary ammonium compound as additives. Lower contact angles and deeper penetration of both ...

  3. Nanopigmented Acrylic Resin Cured Indistinctively by Water Bath or Microwave Energy for Dentures

    Directory of Open Access Journals (Sweden)

    L. S. Acosta-Torres

    2014-01-01

    Full Text Available The highlight of this study was the synthesis of nanopigmented poly(methyl methacrylate nanoparticles that were further processed using a water bath and/or microwave energy for dentures. The experimental acrylic resins were physicochemically characterized, and the adherence of Candida albicans and biocompatibility were assessed. A nanopigmented acrylic resin cured by a water bath or by microwave energy was obtained. The acrylic specimens possess similar properties to commercial acrylic resins, but the transverse strength and porosity were slightly improved. The acrylic resins cured with microwave energy exhibited reduced C. albicans adherence. These results demonstrate an improved noncytotoxic material for the manufacturing of denture bases in dentistry.

  4. Effects of composition and layer thickness of a butyl acrylate/acrylic acid copolymer on the adhesion properties

    Energy Technology Data Exchange (ETDEWEB)

    Ghim, Deoukchen; Kim, Jung Hyeun [University of Seoul, Seoul (Korea, Republic of)

    2016-02-15

    Acrylic pressure-sensitive adhesives are synthesized by solution copolymerization using n-butyl acrylate and acrylic acid (AA) in ethyl acetate anhydrous. The copolymer composition is controlled for good adhesive properties by varying AA content. The monomer conversion is measured by the gravimetric method and FTIR technique. The adhesive layer thickness is measured by scanning electron microscopy, and the adhesive properties are evaluated with loop tack, 180 .deg. peel, and holding time measurements. The peel force increases with increasing the AA content up to 3 wt% and decreases at the AA content higher than 3 wt%, but the tack force decreases with increasing the AA content. The holding time increases with increasing the AA content, and it shows a similar trend with the T{sub g} of adhesives. The increase of layer thickness improves tack and peel forces, but it weakens the holding power. A tape thickness of about 20 μm shows well-balanced properties at 3 wt% AA content in the acrylic copolymer system.

  5. Allergic contact dermatitis to artificial fingernails prepared from UV light-cured acrylates.

    Science.gov (United States)

    Hemmer, W; Focke, M; Wantke, F; Götz, M; Jarisch, R

    1996-09-01

    Contact dermatitis from artificial nails made from self-curing acrylic resins is occasionally reported. Recently, UV light-cured products introducing new acrylics have become available. Our purpose was to identify relevant allergens in commercial light-curing products by patch tests and to evaluate the efficacy of "hypoallergenic" products by inclusion into the test series. Patients wearing photobonded acrylic nails who had perionychial and subonychial eczema were patch tested with an acrylate battery and "hypoallergenic" commercial products. Triethyleneglycol dimethacrylate, hydroxyfunctional methacrylates, and (meth)-acrylated urethanes proved to be relevant allergens in photobonded nail preparations. Methacrylated epoxy resin sensitization was not observed. All "hypoallergenic" products provoked positive reactions. The omission of irritant methacrylic acid in UV-curable products does not reduce the high sensitizing potential of new acrylates. In contrast to the manufacturers' declarations, all "hypoallergenic" products continue to include acrylate functional monomers and therefore continue to cause allergic sensitization.

  6. The filtering, clear-cornea diathermal keratostomy

    DEFF Research Database (Denmark)

    Kessing, Svend Vedel; Nissen, Ole I; Thygesen, John

    2012-01-01

    Is the new micropenetrating, clear-cornea procedure, intrastromal diathermal keratostomy (IDK), an alternative to the intricate "modern trabeculectomy"?......Is the new micropenetrating, clear-cornea procedure, intrastromal diathermal keratostomy (IDK), an alternative to the intricate "modern trabeculectomy"?...

  7. 76 FR 45724 - Clearing Member Risk Management

    Science.gov (United States)

    2011-08-01

    ... COMMISSION 17 CFR Parts 1 and 23 RIN 3038-AD51 Clearing Member Risk Management AGENCY: Commodity Futures... are clearing members. DATES: Submit comments on or before September 30, 2011. ADDRESSES: You may... requirement that a DCO adopt rules addressing each clearing member's risk management policies and procedures...

  8. A key step in the formation of acrylic acid from CO2 and ethylene: the transformation of a nickelalactone into a nickel-acrylate complex.

    Science.gov (United States)

    Fischer, Reinald; Langer, Jens; Malassa, Astrid; Walther, Dirk; Görls, Helmar; Vaughan, Gavin

    2006-06-21

    The reaction of a nickelalactone with dppm, resulting in the formation of a stable binuclear Ni(I) complex with an acrylate, a Ph2P- and a dppm bridge, models a key step in the formation of acrylic acid from CO2 and ethylene.

  9. Occupational methacrylate and acrylate allergy--cross-reactions and possible screening allergens.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Henriks-Eckerman, Maj-Len; Kuuliala, Outi; Jolanki, Riitta

    2010-12-01

    Acrylic resin monomers, especially acrylates and methacrylates, are important occupational allergens. To analyse patterns of concomitant patch test reactions to acrylic monomers in relation to exposure, and to suggest possible screening allergens. We reviewed the patch test files for the years 1994-2009 at the Finnish Institute of Occupational Health for allergic reactions to acrylic monomers, and analysed the clinical records of sensitized patients. In a group of 66 patients allergic to an acrylic monomer, the most commonly positive allergens were three methacrylates, namely ethyleneglycol dimethacrylate (EGDMA), 2-hydroxyethyl methacrylate (2-HEMA) and 2-hydroxypropyl methacrylate (2-HPMA), and an acrylate, namely diethyleneglycol diacrylate (DEGDA). The patterns of concomitant reactions imply that exposure to methacrylates may induce cross-reactivity to acrylates, whereas exposure to acrylates usually does not lead to cross-allergy to methacrylates. Screening for triethyleneglycol diacrylate (TREGDA) in the baseline series was found to be useful, as 3 of 8 patients with diagnosed occupational acrylate allergy might have been missed without the screening. A short screening series of four allergens, EGDMA, DEGDA, 2-HPMA and pentaerythritol triacrylate (PETA), would have screened 93% of our 66 patients; each of the remaining 5 patients reacted to different acrylic monomer(s). © 2010 John Wiley & Sons A/S.

  10. Acrylate and methacrylate contact allergy and allergic contact disease: a 13-year review.

    Science.gov (United States)

    Spencer, Ashley; Gazzani, Paul; Thompson, Donna A

    2016-09-01

    (Meth)acrylates are important causes of contact allergy and allergic contact disease, such as dermatitis and stomatitis, with new and emerging sources resulting in changing clinical presentations. To identify the (meth)acrylates that most commonly cause allergic contact disease, highlight their usefulness for screening, and examine their relationship with occupational and clinical data. A retrospective review of results from patch tests performed between July 2002 and September 2015, in one tertiary Cutaneous Allergy Unit, was performed A series of 28 (meth)acrylates was applied to 475 patients. Results were positive in 52 cases, with occupational sources being identified in 24. Industrial exposures and acrylic nails were responsible for 13 and 10 cases, respectively, with wound dressings being implicated in 7. We found that four individual (meth)acrylates (2-hydroxyethyl acrylate, 2-hydroxypropyl methacrylate, bisphenol A glycerolate dimethacrylate, and ethyl acrylate), if used as a screening tool, could have identified 47 (90.4%) of our positive cases. Our 13-year experience indicates a changing landscape of (meth)acrylate contact allergy and allergic contact disease, with an observed shift in exposures away from manufacturing and towards acrylic nail sources. Wound dressings are highlighted as emerging sources of sensitization. Larger studies are required to establish the sensitivity and specificity of the four (meth)acrylates proposed for potential screening. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  11. 10 years of patch testing with the (meth)acrylate series.

    Science.gov (United States)

    Kanerva, L; Jolanki, R; Estlander, T

    1997-12-01

    Statistics on 10 years of patch testing with 30 (meth)acrylates were compiled. Altogether 275 patients were patch tested and 48 patients (17.5%) had an allergic reaction to at least 1 (meth)acrylate. The (meth)acrylates most often provoking an allergic patch test reaction were 2-hydroxyethyl acrylate (2-HEA; 12.1%), 2-hydroxypropyl methacrylate (2-HPMA; 12.0%) and 2-hydroxyethyl methacrylate (2-HEMA; 11.4%). No allergic reactions were caused by 2-ethylhexyl acrylate (2-EHA), 2,2-bis[4-(methacryloxy)phenyl]propane (BIS-MA), trimethylolpropane triacrylate (TMPTA), oligotriacrylate 480 (OTA 480), N,N-methylenebisacrylamide (MBAA), or ethyl cyanoacrylate (ECA). The frequency of allergic patch test reactions presented cannot be considered as a "ranking" list of the most sensitizing (meth)acrylate compounds. In order to be able to judge the sensitization capacity of various (meth)acrylate compounds in humans, it would be necessary to have detailed information on the exposure history of the patients studied, including the purity of the (meth)acrylate compounds. Currently, this is not possible because (meth)acrylate-containing products regularly contain undeclared (meth)acrylate compounds.

  12. The effect of low dose teicoplanin-loaded acrylic bone cement on biocompatibility of bone cement.

    Science.gov (United States)

    Öztemür, Zekeriya; Sümer, Zeynep; Tunç, Tutku; Pazarcé, Özhan; Bulut, Okay

    2013-06-01

    Antibiotic-loaded acrylic bone cement (polymethylmethacrylate, PMMA) is used to prevent or treat infection in total joint replacement surgery. The purpose of this study was to investigate biocompatibility and cytotoxicity of the teicoplanin-loaded acrylic bone cement. Cytotoxicity examination of acrylic bone cement balls and 400 mg teicoplanin added acrylic bone cement balls conducted by MTT (3-[4,5-dimethylthiazol-2-yl]-2,5 diphenyl tetrazolium bromide) assay. SEM (Scanning electron microscopy) was used to observe adhesion and spreading of cells on surface of the balls. Cytotoxicity examination conducted by MTT assay on acrylic bone cement balls and teicoplanin-added acrylic bone cement balls revealed no cytotoxicity. SEM analysis put forward that cells started to proliferate and adhere on surface of the samples in both groups as a result of 48-hour incubation and that the cell proliferation over acrylic bone cement and teicoplanin-added acrylic bone cement was similar. As a consequence, there was no cytotoxicity in acrylic bone cement and teicoplanin-added acrylic bone cement groups according to results of MTT assay. On the other hand, results of SEM showed that biocompatibility of both groups was similar. In conclusion, teicoplanin-loaded bone cement did not change biocompatibility of bone cement in studied dose.

  13. Plant oil-based shape memory polymer using acrylic monolith

    Directory of Open Access Journals (Sweden)

    T. Tsujimoto

    2015-09-01

    Full Text Available This article deals with the synthesis of a plant oil-based material using acrylic monolith. An acrylic monolith bearing oxirane groups was prepared via simple technique that involved the dissolution of poly(glycidyl methacrylate-comethyl methacrylate (PGMA in ethanolic – aqueous solution by heating and subsequent cooling. The PGMA monolith had topologically porous structure, which was attributed to the phase separation of the polymer solution. The PGMA monolith was impregnated by epoxidized soybean oil (ESO containing thermally-latent catalyst, and the subsequent curing produced a crosslinked material with relatively good transparency. The Young’s modulus and the tensile strength of polyESO/PGMA increased compared with the ESO homopolymer. The strain at break of polyESO/PGMA was larger than that of the ESO homopolymer and crosslinked PGMA. Furthermore, polyESO/PGMA exhibited good shape memory-recovery behavior.

  14. Characterization of methacrylated alginate and acrylic monomers as versatile SAPs.

    Science.gov (United States)

    Mignon, Arn; Vermeulen, Jolien; Graulus, Geert-Jan; Martins, José; Dubruel, Peter; De Belie, Nele; Van Vlierberghe, Sandra

    2017-07-15

    Superabsorbent polymers (SAPs) based on polysaccharides, especially alginate, could offer a valuable solution in a plethora of applications going from drug delivery to self-healing concrete. This has already been proven with both calcium alginate and methacrylated alginate combined with acrylic acid. In this manuscript, the effect of varying the degree of methacrylation and use of a combination of acrylic acid and acrylamide is investigated to explore the effects on the relevant SAP characteristics. The materials showed high gel fractions and a strong swelling capacity up to 630gwater/gSAP, especially for superabsorbent polymers with a low degree of substitution. The SAPs also showed only a limited hydrolysis in aqueous and cement filtrate solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Acrylated Composite Hydrogel Preparation and Adsorption Kinetics of Methylene Blue

    Directory of Open Access Journals (Sweden)

    Jinpeng Wang

    2017-10-01

    Full Text Available By using cyclodextrin (α-CD self-assembly into a hydrogel with the triblock copolymer Pluronic F127, nanomicrocrystalline cellulose was introduced into a gel system to form a composite CNC-β-CD/α-CD/Pluronic F127 hydrogel (CCH. CCH was modified further by grafting acrylic acid to form a novel acrylated composite hydrogel (ACH. The swelling degree of ACH was 156 g/g. Adsorption isotherms show that the adsorption process for methylene blue proximity fitted the Freundlich model. The adsorption kinetics showed that ACH followed a quasi-second-order kinetic model. Methylene blue desorption showed that ACH was a temperature- and pH-dependent gel. Repeated adsorption and desorption experiments were carried out three times, and the removal rate of methylene blue at 75 mg/L was still 70.1%.

  16. Terra Nullius: Colonial Violence in Prynne’s Acrylic Tips

    Directory of Open Access Journals (Sweden)

    Matthew Hall

    2016-06-01

    Full Text Available Examining J.H. Prynne’s 'Acrylic Tips' through a series of analogous readings, this paper identifies the location, characters, and themes of the poem. By examining the poem and the contiguities with 'Her Weasel’s Wild Returning', 'Acrylic Tips' is positioned against the historical decree of terra nullius over the sovereign land of Australia. The poem is read against and situated in the colonial and linguistic history of Australia. Read as a pastoral elegy, the poem depicts a hierarchy of human dominance over nature, which finds its ends in the colonial shearing shed, as well as the genetic laboratory. These positions are ultimately argued to be socio-political by-products of the colonial dominance of Indigenous culture and nature.

  17. Imparting permanent antimicrobial activity onto viscose and acrylic fabrics.

    Science.gov (United States)

    Mekewi, M; El-Sayed, A Atef; Amin, M S; Said, Hala I

    2012-05-01

    Viscose and acrylic fabrics were aminated to enhance metal chelation of Cu, Zn and Ni for the purpose of imparting fabrics antimicrobial activity against Escherichia coli and Staphylococcus aureus. Fabrics were firstly epoxidized using epichlorohydrin prior amination. Optimization of the reaction conditions, e.g., temperature, medium pH, amine type and metal type and their concentrations, are reported. Aminated fabrics of viscose and acrylic were shown to be viable for chelation with divalent metal cations. The overall results revealed that antibacterial resistance of metalized aminated fabrics that the activity trend of metals is in the order Cu-complex>Zn-complex>Ni-complex with regard to fighting of microorganisms and permanent even after 10 washing. Reaction mechanism of epoxidation, amination and metal chelation of fabrics are offered supported by FT-IR structural study, nitrogen content and atomic absorption spectroscopy. Copyright © 2012 Elsevier B.V. All rights reserved.

  18. Softec HD hydrophilic acrylic intraocular lens: biocompatibility and precision

    Directory of Open Access Journals (Sweden)

    Ladan Espandar

    2011-01-01

    Full Text Available Ladan Espandar1, Shameema Sikder2, Majid Moshirfar31Department of Ophthalmology, Tulane University, New Orleans, LA, USA; 2Wilmer Eye Institute, Johns Hopkins University, Baltimore, MD, USA; 3John A Moran Eye Center, University of Utah, Salt Lake City, UT, USAAbstract: Intraocular lens development is driven by higher patient expectations for ideal visual outcomes. The recently US Food and Drug Administration-approved Softec HD™ lens is an aspheric, hydrophilic acrylic intraocular lens (IOL. The hydrophilic design of the lens is optimized to address dysphotopsia while maintaining biocompatibility, optical clarity, resistance to damage, and resistance to biocontamination. Aspheric lenses decrease postoperative spherical aberration. The addition of the Softec lens provides clinicians with another option for IOL placement; however, randomized comparative studies of this lens to others already on the market remain to be completed.Keywords: hydrophilic acrylic intraocular lens, Softec HD intraocular lens, aspheric intraocular lens, IOL

  19. Dielectric Constant Measurements on Poly Iron-Nickel Acrylate

    Science.gov (United States)

    Chohan, M. H.; Khwaja, F. A.; Bukhari, A. H. S.

    Measurements of the impedance (z) and the dielectric constant (ɛ) on poly acrylates have been made as a function of temperature and frequency by employing a parallel RLC circuit arrangement and using standard formula. The values of ɛ have been determined after identifying the resonance frequencies of the circuit at different temperatures. Variation of ‘z’ with frequency and ɛ as a function of temperature are presented in the graphs.

  20. Hemocompatibility of Chitosan/poly(acrylic acid) Grafted Polyurethane Tubing

    OpenAIRE

    Lee, Hyun-Su; Tomczyk, Nancy; Kandel, Judith; Composto, Russell J.; Eckmann, David M.

    2013-01-01

    The activation and adhesion of platelets or whole blood exposed to chitosan (CH) grafted surfaces is used to evaluate the hemocompatibility of biomaterials. The biomaterial surfaces are polyurethane (PU) tubes grafted with an inner poly(acrylic acid) (PAA) and an outer CH or quaternary ammonium modified CH (CH-Q) brush. The CH, CH-Q and PAA grafted layers were characterized by ellipsometry and fluorescence microscopy. Material wear tests demonstrate that CH (CH-Q) is stably grafted onto PU tu...

  1. Slow- Release Fertilizer Formulation Using Acrylic and Chitosan Coating

    Directory of Open Access Journals (Sweden)

    Lili Handayani

    2015-01-01

    Full Text Available The low-efficiency problem in fertilizer application can be overcome by controlling fertilizer solubility, i.e. by rendering the fertilizer to be released gradually; such material is also known as slow-release fertilizer (SRF. This research was aimed to formulate SRF by coating technique using acrylic and chitosan as the coating material, and to evaluate fertilizer resistance to too fast disintegration, and rate of nutrient release method. The results demonstrated that fertilizer formulation containing N, P, K, Fe, Cu, and Zn with granulation technique yielded 74% of granules with 2-5 mm in diameter. The SRFs (formulated fertilizer with acrylic or chitosan coating were more resistant to water pounding than non-SRF. Furthermore, shaking test with distilled water or 2% citric acid, or by percolation test with distilled water showed that the SRFs had lower nutrient solubility than the non-SRFs. The results of shaking test also specifically indicated that coating with acrylic made the fertilizer more resistant to the citric acid,suggesting that this coating material would be more suitable in acidic soils. The SRFs formulated with the addition of chitosan during blending of micronutrients prior to mixing with macronutrients, granulation, and final coating exhibited lower nutrient solubility than the SRFs without the pre-coating chitosan addition.

  2. Acrylate Functionalized Tetraalkylammonium Salts with Ionic Liquid Properties

    Directory of Open Access Journals (Sweden)

    Silvia Janietz

    2012-05-01

    Full Text Available Acrylate functionalized ionic liquids based on tetraalkylammonium salts with terminal acrylates- and methylacrylates were synthesized. Melting points and ionic conductivity of twenty compounds in six groups were determined. Within one group the effect of three different counterions was investigated and discussed. The groups differ in cationic structure elements because of their functional groups such as acrylate and methacrylate, alkyl residues at the nitrogen and number of quaternary ammonium atoms within the organic cation. The effect of these cationic structure elements has been examined concerning the compiled parameters with a view to qualifying them as components for solid state electrolytes. The newly synthesized ionic liquids were characterized by NMR and FTIR analysis. The exchange of halide ions like bromide as counter ions to weakly coordinating [PF6], [OTf] or [TFSI] reduces the melting points significantly and leads to an ion conductivity of about 10−4 S/cm at room temperature. In the case of the dicationic ionic liquid, an ion conductivity of about 10−3 S/cm was observed.

  3. Amphiphilic photosensitive dextran-g-poly(o-nitrobenzyl acrylate) glycopolymers.

    Science.gov (United States)

    Soliman, Soliman Mehawed Abdellatif; Colombeau, Ludovic; Nouvel, Cécile; Babin, Jérôme; Six, Jean-Luc

    2016-01-20

    Among all photosensitive monomers reported in the literature, o-nitrobenzyl acrylate (NBA) was selected in this present study. Two strategies were compared to produce azido-terminated poly(o-nitrobenzyl acrylate) (PNBA) using controlled Single Electron Transfer-Living Radical Polymerization (SET-LRP). In a parallel way, dextran (Dex) was modified by the introduction of several alkynyl-terminated hydrophobic chains. Finally, an Huisgen-type Copper (I)-catalyzed Azide-Alkyne Cycloaddition (CuAAC) click-chemistry was carried out to produce amphiphilic Dex-g-PNBA glycopolymers with different number and length of PNBA grafts. 2D DOSY (1)H NMR was used to prove the formation of such glycopolymers. Preliminary study on Dex-g-PNBA self-assembly was done by measuring the critical water content (CWC) above which Dex-g-PNBA started to auto-organize themselves to produce nano-objects. Finally, under UV irradiation, PNBA grafts turn into poly(acrylic acid) ones giving light-sensitive properties to such amphiphilic Dex-g-PNBA. Such properties were evaluated and compared with those of PNBA. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Customised acrylic nasal stents following recanalisation of modified Young's procedure.

    Science.gov (United States)

    Pavithran, P; Pujary, K; Mahesh, S G; Parul, P; Aziz, B

    2010-08-01

    Maintaining the patency of the nasal vestibule following recanalisation of a modified Young's procedure can be a difficult task, as restenosis is quite common. Sixteen patients underwent recanalisation of a modified Young's procedure, between January 2005 and December 2007, in the ENT--head and neck surgery department of a tertiary centre. Three different stent types were used following recanalisation: silicone suction tube tips, dental wax plate stents and customised acrylic stents. The silicone suction tube stents prevented restenosis. They were visible in the post-operative period, and there appeared to be some blunting of the nasal valve region, with no functional impairment. Dental wax plates had a high rate of restenosis and were uncomfortable and unsightly. The customised acrylic stents were more acceptable in the post-operative period, and enabled nasal valve angulation to be maintained. The customised acrylic stent described was a superior alternative to such stenting methods as repeated packing, silicone suction tubes and dental wax plates, following recanalisation of a modified Young's procedure.

  5. Microhardness of heat cure acrylic resin after treatment with disinfectants.

    Science.gov (United States)

    Amin, Faiza; Rehman, Abdur; Abbas, Muhammad

    2015-08-01

    To evaluate the effect of disinfectants and distilled water on the micro-hardness of heat cure acrylic resins. The case-control study was conducted at Dr. Ishrat-ul-Ebad Khan Institute of Oral Health Sciences, Dow University of Health Sciences, and Nadirshaw Edulji Dinshaw University of Engineering and Technology, Karachi, from April to October 2011. Specimens were fabricated from heat cure acrylic resin material and they were divided into four equal groups. Group 1 was evaluated at baseline and was taken as the control group. Group 2 was immersed in distilled water for 20 minutes, Group 3 in1% sodium hypochlorite for 20 minutes, and Group 4 in 2% alkaline gluteraldehyde for 10 minutes. All specimens were polished, stored in distilled water for 24 hours prior to experiment. All the specimens were immersed twice daily for a total of 60 days after which they were tested for Vickers micro-hardness test. Statistical analysis was conducted with one-way analysis of variance and Tukey post hoc test (a=0.05). There were 72 specimens divided into four groups of 18(25%) each. Statistically significant differences were found among all groups (pacrylic resins. Group 4 showed the most reduction in the hardness value which was followed by Group 3. The hardness of heat cure acrylic resin was affected by disinfectants.

  6. Acrylic interpenetrating polymer network dielectric elastomers for energy harvesting

    Science.gov (United States)

    Brochu, Paul; Niu, Xiaofan; Pei, Qibing

    2011-04-01

    Dielectric elastomer energy harvesters are an emerging technology that promise high power density, low cost, scalability, and the capability of fitting niche markets that have yet to be exploited. To date, materials issues that limit their overall performance have hampered the full potential of these devices. In order to supplant existing technologies, even in niche markets, dielectric elastomer generators must increase their reliability and energy density. Previous work has indicated that stiffer elastomers should be capable of higher energy densities; the increased stiffness of the elastomer films should results in lower Maxwell pressure induced strains, and thus allow the elastomer to relax further, resulting in a larger swing in capacitance and larger energy gains. In this paper we examine the use of VHB-based acrylic interpenetrating polymer network dielectric elastomers with a trimethylolpropane trimethacrylate additive network for energy harvesting purposes. We test films with varying additive content and compare their performance with highly prestrained VHB acrylic elastomers. We show that by increasing additive content, Maxwell induced strains can be suppressed and larger energy gains can be achieved at higher bias fields. Moreover, the introduction of the additive network stabilizes the highly prestrained acrylic elastomers mechanically, thereby increasing their mechanical robustness. However, the interpenetrating polymer network films suffer from an increase in viscoelastic behavior that hinders their overall performance.

  7. Biodegradation and sorption properties of polydisperse acrylate polymers.

    Science.gov (United States)

    Rittmann, B E; Sutfin, J A; Henry, B

    Polyacrylate (PA), which is widely used in disposable diapers, is synthesized by polymerization and cross-linking of acrylate. During the synthesis, 3-6% of the polyacrylate polymers is not incorporated into the absorbent material, but remains soluble. If the soluble PA is mobilized from a landfill, it could enter the groundwater. Therefore, the biodegradation and adsorption properties of soluble polymers contained in PA are determined in this study. The soluble PA is highly polydisperse, and the fraction tested has a weight-average molecular-weight of 16,700 and a range extending from 10(3) to 10(5). Sand-column tracer tests show that about 1% of the polyacrylate is unadsorbed, but the remainder has a retardation factor that averages at least 58. Biodegradation kinetics are determined in completely mixed biofilm reactors having a methanogenic consortium grown on glucose. The polyacrylate fraction, as well as glucose and acrylate, are removed and mineralized to CO2. The Monod parameters for the polyacrylate are: maximum specific rate of substrate utilization = 0.0016 gC/g biomass-day, and half-maximum-rate concentration = 0.79 gC/m3. Although these kinetics are much slower than for glucose and acrylate, significant degradation and mineralization are observed.

  8. Comparison of patient satisfaction with acrylic and flexible partial dentures.

    Science.gov (United States)

    Akinyamoju, Clara Arianta; Ogunrinde, Tunde Joshua; Taiwo, Juliana Obontu; Dosumu, Oluwole Oyekunle

    2017-01-01

    Restoration of partial edentulous mouth may be done using a variety of treatment options. Removable partial denture (RPD) is commonly used because of its availability. RPDs from flexible resins unlike those from acrylic engage hard and soft tissue undercuts and feel more comfortable in the mouth. The aim of the study was to compare satisfaction with dentures made from these two types of materials. It was a quasi-experimental study among thirty patients at the Prosthetics Clinic, University College Hospital, Ibadan. Patients aged 16 years or more, requiring RPDs with one to three missing teeth in the anterior region of either the upper or lower arch participated. A modified semi-structured interviewer-administered questionnaire was used to collect data on sociodemographics and oral health variables. The level of satisfaction was assessed using a visual analogue scale. Data were analysed using descriptive and multivariate statistics at a significance level of P dentures, 6 (20.0%) with acrylic dentures while 3 (10.0%) were equally satisfied with both types of dentures (P = 0.04). Subjects were more satisfied with the flexible RPD than the acrylic resin RPD.

  9. Development of palm oil-based UV-curable epoxy acrylate and urethane acrylate resins for wood coating application

    Science.gov (United States)

    Tajau, Rida; Ibrahim, Mohammad Izzat; Yunus, Nurulhuda Mohd; Mahmood, Mohd Hilmi; Salleh, Mek Zah; Salleh, Nik Ghazali Nik

    2014-02-01

    The trend of using renewable sources such as palm oil as raw material in radiation curing is growing due to the demand from the market to produce a more environmental friendly product. In this study, the radiation curable process was done using epoxy acrylate and urethane acrylate resins which are known as epoxidised palm olein acrylate (EPOLA) and palm oil based urethane acrylate (POBUA), respectively. The purpose of the study was to investigate curing properties and the application of this UV-curable palm oil resins for wood coating. Furthermore, the properties of palm oil based coatings are compared with the petrochemical-based compound such as ebecryl (EB) i.e. EB264 and EB830. From the experiment done, the resins from petrochemical-based compounds resulted higher degree of crosslinking (up to 80%) than the palm oil based compounds (up to 70%), where the different is around 10-15%. The hardness property from this two type coatings can reached until 50% at the lower percentage of the oligomer. However, the coatings from petrochemical-based have a high scratch resistance as it can withstand at least up to 3.0 Newtons (N) compared to the palm oil-based compounds which are difficult to withstand the load up to 1.0 N. Finally, the test on the rubber wood substrate showed that the coatings containing benzophenone photoinitiator give higher adhesion property and their also showed a higher glosiness property on the glass substrate compared to the coatings containing irgacure-819 photoinitiator. This study showed that the palm oil coatings can be a suitable for the replacement of petrochemicals compound for wood coating. The palm oil coatings can be more competitive in the market if the problems of using high percentage palm oil oligomer can be overcome as the palm oil price is cheap enough.

  10. Waterborne hyperbranched alkyd-acrylic resin obtained by mini emulsion polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Murillo, Edwin, E-mail: edwinalbertomurillo@gmail.com [Grupo de Investigacion en Materiales Polimericos (GIMAPOL), Universidad Francisco de Paula Santander, San Jose de Cucuta (Colombia); Lopez, Betty [Grupo de Investigacion en Ciencia de los Materiales, Universidad de Antioquia, Calle, Medellin (Colombia)

    2016-10-15

    Four waterborne hyper branched alkyd-acrylic resins (HBRAA) were synthesized by mini emulsion polymerization from a hyper branched alkyd resin (HBR), methyl methacrylate (MMA), butyl acrylate (BA) and acrylic acid (AA), by using benzoyl peroxide (BPO) and ammonium persulfate (AP) as initiators. The reaction between HBR and acrylic monomers was evidenced by differential scanning calorimetric (DSC), nuclear magnetic resonance (NMR) and gel permeation chromatography (GPC). The conversion percentage, glass transition temperature (T{sub g}), content of acrylic polymer (determined by soxhlet extraction) and molecular weight increased with the content of acrylic monomers used in the synthesis. The main structure formed during the synthesis was the HBRAA. The analysis by dynamic light scattering (DLS) showed that the particle size distribution of HBRAA2, HBRAA3 and HBRAA4 resins were mainly mono modal. The film properties (gloss, flexibility, adhesion and drying time) of the HBRAA were good. (author)

  11. Contact dermatitis to incontinency pads in a (meth)acrylate allergic patient.

    Science.gov (United States)

    Giroux, Lyne; Pratt, Melanie D

    2002-09-01

    The authors report a case of a 47-year-old woman who suffered a severe allergic contact dermatitis (ACD) in the vulvar area after using Poise thin incontinency pads. She had a past history of ACD after the use of sculptured acrylic nails and after the installation of a dental crown. The aim of this report is to show the spectrum of (meth)acrylate allergy in one individual. Patch testing of moistened inner and outer aspect of the pad was performed. We also patch tested with the North American Contact Dermatitis Group series of 50 allergens, the dentistry series, various catalysts and inhibitors used in acrylic resin systems, and some epoxy acrylates. Positive ACD reaction occurred to both sides of the pad, with the inner aspect being stronger than the outer aspect. There were also multiple (meth)acrylate allergies. This case shows a new potential source of allergy to (meth)acrylates. Copyright 2002, Elsevier Science (USA). All rights reserved.

  12. Allergic contact dermatitis due to urethane acrylate in ultraviolet cured inks.

    Science.gov (United States)

    Nethercott, J R; Jakubovic, H R; Pilger, C; Smith, J W

    1983-08-01

    Seven workers exposed to ultraviolet printing inks developed contact dermatitis. Six cases were allergic and one irritant. A urethane acrylate resin accounted for five cases of sensitisation, one of which was also sensitive to pentaerythritol triacrylate and another also to an epoxy acrylate resin. One instance of allergy to trimethylpropane triacrylate accounted for the sixth case of contact dermatitis in this group of workers. An irritant reaction is presumed to account for the dermatitis in the individual not proved to have cutaneous allergy by patch tests. In this instance trimethylpropane triacrylate was thought to be the most likely irritating agent. Laboratory investigation proved urethane acrylate to be an allergen. The results of investigations of the sensitisation potentials of urethane acrylate, methylmethacrylate, epoxy acrylate resins, toluene-2,4-diisocyanate, and other multifunctional acrylic monomers in the albino guinea pig are presented. The interpretation of such predictive tests is discussed.

  13. Occupational allergic contact dermatitis caused by exposure to acrylates during work with dental prostheses.

    Science.gov (United States)

    Kanerva, L; Estlander, T; Jolanki, R; Tarvainen, K

    1993-05-01

    Between 1974 and 1992, we were consulted by 4 patients (an orthodontist, 2 dental technicians and a dental worker trained in-house) who had developed occupational allergic contact dermatitis from working with dental prostheses. All patients had positive allergic patch test reactions to methyl methacrylate (MMA), the acrylate which is the most widely used in work with prostheses. All but the orthodontist also reacted to dimethacrylates, which are used in cross-linked dental prostheses. The last patient, investigated in 1992, had been exposed mainly to light-cured acrylics, which are similar in composition to dental composite resins. These acrylics, only recently introduced into prosthetic work, contain more potent acrylic sensitizers than MMA. Accordingly, dental personnel working with prostheses may face a higher risk of sensitization than previously. To detect cases of occupational allergic contact dermatitis, we suggest that patients working with dental prostheses should be patch tested with MMA, 2-hydroxyethyl methacrylate, dimethacrylates, epoxy acrylates and urethane acrylates.

  14. Synthesis and characterization of superabsorbent hydrogels based on hydroxyethylcellulose and acrylic acid.

    Science.gov (United States)

    Fekete, Tamás; Borsa, Judit; Takács, Erzsébet; Wojnárovits, László

    2017-06-15

    Hydroxyethylcellulose (HEC)/acrylic acid (AAc) copolymer gels with superabsorbent properties were synthesized from aqueous solutions by radiation-initiated crosslinking. The effect of the acrylic acid content on gel properties was determined at different synthesis conditions. The partial replacement of the cellulose derivative with acrylic acid improved the gelation, leading to higher gel fraction and lower water uptake even in very low concentrations (1-5%). In the presence of acrylic acid lower dose and solute concentration was required for the gel synthesis. The molecular properties of the hydroxyethylcellulose also had a major effect on the gelation: higher molecular mass resulted in better gel properties. The acrylic acid also affected the electrolyte sensitivity of the hydrogels: while pure HEC gels were unaffected by the ionic strength of the solvent, the water uptake of HEC/AAc gels decreased with the salt concentration. The sensitivity also depended on the acrylic acid ratio. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Effects of laboratory disinfecting agents on color stability of denture acrylic resins.

    Science.gov (United States)

    McNeme, S J; von Gonten, A S; Woolsey, G D

    1991-07-01

    This study determined the effects of chemical disinfecting agents on denture acrylic resins. Tested resins included the products CH Lucitone, Triad VLC, and Truliner. The disinfecting agents were sodium hypochlorite, Exspor, Cidex, and Wescodyne-D. Acrylic resin samples were placed in the various disinfecting agents and then evaluated for color changes at time intervals ranging from 15 minutes to 72 hours. No observable color change of any acrylic resin was seen before 2 hours. Both 1% sodium hypochlorite and 2% Cidex disinfectants produced the least discoloration of the acrylic resins, and Wescodyne-D disinfectant produced the most acrylic resin discoloration. Truliner resin discolored more than Triad VLC resin, and both underwent more color change than CH Lucitone resin. If manufacturers' recommended disinfecting times are followed, clinical and laboratory disinfection of acrylic resin dentures should cause no observable color change.

  16. Research of morphology structure and properties of bamboo charcoal acrylic fiber

    Science.gov (United States)

    Zhang, Yongjiu; Feng, Aifen

    2015-07-01

    In order to understand the properties of bamboo charcoal acrylic fiber, the tensile properties, friction properties and hygroscopicity of it, the bamboo charcoal acrylic fiber and the ordinary acrylic fiber were tested, compared and analyzed. The burning behaviors of the two kinds of fibers were observed by burning test, and their cross-sectional and longitudinal morphology was observed with scanning electron microscope (SEM). The SEM pictures showed that there are the uneven sizes of microspores on the surface of bamboo charcoal acrylic fiber and in it. It was found that the friction coefficients of the bamboo charcoal acrylic fiber are smaller and its tensile and moisture absorption are better than those of the ordinary acrylic fiber. However, there are no obvious differences of the burning behaviors between the two fibers.

  17. Comparison between an Acrylic Splint Herbst and an Acrylic Splint Miniscrew-Herbst for Mandibular Incisors Proclination Control

    Directory of Open Access Journals (Sweden)

    Antonio Manni

    2014-01-01

    Full Text Available Aim. The aim of this study is to compare dental and skeletal effects produced by an acrylic splint Herbst with and without skeletal anchorage for correction of dental class II malocclusion. Methods. The test group was formed by 14 patients that were treated with an acrylic splint miniscrew-Herbst; miniscrews were placed between mandibular second premolars and first molars; controls also consisted of 14 subjects that were treated with an acrylic splint Herbst and no miniscrews. Cephalometric measurements before and after Herbst treatment were compared. The value of α for significance was set at 0.05. Results. All subjects from both groups were successfully treated to a bilateral Class I relationship; mean treatment time was 8,1 months in the test group and 7.8 in the controls. Several variables did not have a statistical significant difference between the two groups. Some of the variables, instead, presented a significant difference such as incisor flaring, mandibular bone base position, and skeletal discrepancy. Conclusions. This study showed that the Herbst appliance associated to miniscrews allowed a better control of the incisor flaring with a greater mandibular skeletal effect.

  18. The potential dermal irritating effect of residual (meth)acrylic monomers in pressure sensitive adhesive tapes.

    Science.gov (United States)

    Tokumura, Fumio; Matsui, Tetsuya; Suzuki, Yasuko; Sado, Masashi; Taniguchi, Masaharu; Kobayashi, Ichiro; Kamiyama, Masashi; Suda, Shin; Nakamura, Atsushi; Yamazaki, Yuhiro; Yamori, Akira; Igarashi, Ryosuke; Kawai, Jun; Oka, Keiji

    2010-01-01

    It is generally thought that residual unpolymerized (meth)acrylic monomers commonly found in pressure sensitive adhesive tapes for medical use may cause dermal irritation, but a systematic study has never been carried out. Therefore, we assessed the potential dermal irritating effect of residual (meth)acrylic monomers. We studied seven acrylic monomers, acrylic acid (AA), methyl acrylate (MA), ethyl acrylate (EA), n-butyl acrylate (n-BA), n-hexyl acrylate (n-HA), 2-ethylhexyl acrylate (2-EHA) and 2-hydroxyethyl acrylate (HEA), as well as three methacrylic monomers, methacrylic acid (MAA), methyl methacrylate (MMA) and 2-hydroxyethyl methacrylate (2-HEMA). We first examined their cytotoxic effect on a cultured dermis model using the MTT method to determine their EC(50) and then performed a primary irritation test in rabbits using the monomers at three different concentrations (i.e., EC(50) , one-tenth EC(50) and 10 times EC(50)). Marked variations were found in cytotoxic and dermal irritating activities among the (meth)acrylic monomers tested. HEA exhibited the most potent dermal irritation having the lowest erythema dose (the concentration which gives a primary dermal irritation index of 1.00) of 460 ppm. But the other monomers exhibited less potent dermal irritation (lowest erythema doses > or =1000 ppm). For the monomers, significant correlation was found between cytotoxic activity and in vivo dermal irritating activity. Our results show that residual unpolymerized (meth)acrylic monomers in adhesive tapes are unlikely to induce skin irritation except for HEA. This study also suggests that cultured skin models are extremely useful as a screening method for chemical substances that could potentially cause dermal irritating activity.

  19. N-Butyl acrylate polymer composition for solar cell encapsulation and method

    Science.gov (United States)

    Gupta, Amitava (Inventor); Ingham, John D. (Inventor); Yavrouian, Andre H. (Inventor)

    1983-01-01

    A polymer syrup for encapsulating solar cell assemblies. The syrup includes uncrosslinked poly(n-butyl)acrylate dissolved in n-butyl acrylate monomer. Preparation of the poly(n-butyl)acrylate and preparation of the polymer syrup is disclosed. Methods for applying the polymer syrup to solar cell assemblies as an encapsulating pottant are described. Also included is a method for solar cell construction utilizing the polymer syrup as a dual purpose adhesive and encapsulating material.

  20. The Mechanical Strength of Acrylic Palatal Plates Reinforced with Net or Bundle Glass Fibers

    OpenAIRE

    Hedzelek, W.; Gajdus, P.; Joniak, S.

    2002-01-01

    The aim of the study was to evaluate the resistant forces of acrylic palatal plates reinforced with glass net and unidirectional glass fibers. The form and models of the edentulous jaw (Frasaco) were used in the study. Palatal plates were made from hot polymerised acrylic SR Triplex Hot (Ivoclar). In the total reinforced method the studied palatal plates used were reinforced with one or three layers of fiber glass net (Stick Net). In the partial reinforced method acrylic palatal plates wer...

  1. Properties of Ultra-Violet Cured Poly(diemthylsiloxane)-Urea Acrylates.

    Science.gov (United States)

    1984-11-01

    poly(dimethylsiloxane) material using a mixture of isobornyl acrylate (IBA) and acrylic acid (AA) as a reactive diluent. Unfortunately, the tensile data...RD-fi48 570 PROPERTIES OF ULTRA VIOLET CURED / POLY(DIEMTHYLSILOXANE)-UREA ACRYLATES (U) WISCONSIN UNIV-MADISON DEPT OF CHEMICAL ENGINEERING X YU ET...SwbIffe) S YEo EOT0PRO OE Properties of Ultra-Violet Cured Poly(dimethyl- Interim Technicial Report siloxane)-Urea Acrylates 6. P9011O.11146N ONG, AREPORT1

  2. Screening for acrylate/methacrylate allergy in the baseline series: our experience in Sweden and Singapore.

    Science.gov (United States)

    Goon, Anthony Teik-Jin; Bruze, Magnus; Zimerson, Erik; Goh, Chee-Leok; Soo-Quee Koh, David; Isaksson, Marléne

    2008-11-01

    No studies to specifically determine the prevalence of contact allergy to acrylates/methacrylates in patch tested populations have been published. To determine the prevalence of acrylate/methacrylate allergy in all patients tested to the baseline patch test series. Five acrylate/methacrylate allergens (2-hydroxyethyl methacrylate, methyl methacrylate, ethylene glycol dimethacrylate, triethylene glycol diacrylate, and 2-hydroxypropyl acrylate) were included in the baseline series for at least 2 years in Malmö and Singapore. Thirty-eight patients in total had reacted to acrylate/methacrylate allergens in the baseline series during the study period in both populations. In Malmö, there were 26 (1.4%) patients with positive patch tests to acrylate/methacrylate allergens, 14 of whom had relevant reactions. In Singapore, there were 12 (1.0%) patients with positive patch tests to acrylate/methacrylate allergens, but only 1 had relevant reactions. If we had not added acrylate/methacrylate allergens to the baseline series, we would not have patch tested 13/26 (50%) of the positive reactors in Malmö and 11/12 (92%) of the positive reactors in Singapore. The overall proportion of missed positive reactors would have been 24/38 (63%). The prevalence of acrylate/methacrylate allergy in our patch tested dermatitis populations is 1.4% in Malmö and 1.0% in Singapore.

  3. Occupational respiratory hypersensitivity caused by preparations containing acrylates in dental personnel.

    Science.gov (United States)

    Piirilä, P; Kanerva, L; Keskinen, H; Estlander, T; Hytönen, M; Tuppurainen, M; Nordman, H

    1998-11-01

    Allergic contact dermatitis caused by acrylate compounds is common in dental personnel; they also often complain of work-related respiratory or conjunctival symptoms. The aim of the present study was to report the cases of acrylates induced respiratory hypersensitivity in dental personnel diagnosed in Finland during the last 6 years. Occupational asthma, rhinitis, laryngitis and pharyngitis cases were diagnosed according to patient history, PEF monitoring, and a work-simulating provocation test. Twelve cases of respiratory hypersensitivity caused by acrylates diagnosed in dental personnel (six dentists and six dental nurses) in 1992-97 are reported. During this period one case of conjunctivitis and one of laryngitis have been published separately. Nine cases of occupational asthma, two rhinitis cases, and one laryngitis case were verified according to the challenge tests with dental acrylate compounds (acrylates, methacrylates and epoxy acrylates). Only three patients had positive skin-prick test reactions to common environmental allergens, and none reacted to acrylates in the skin-prick tests. Five patients had an elevated total IgE (>110 kU/L). PEF follow-up showed an occupational effect in all examined eight patients with diagnosed asthma. The mean duration of exposure to acrylates was 22 years, and the duration of respiratory symptoms 8 years. The results indicate that acrylates constitute an important hazard for dental workers. The mechanism of respiratory hypersensitivity is still unknown, and it is probably not IgE-mediated.

  4. (Meth)Acrylate Occupational Contact Dermatitis in Nail Salon Workers: A Case Series.

    Science.gov (United States)

    DeKoven, Samuel; DeKoven, Joel; Holness, D Linn

    Recently, many cases of acrylate-associated allergic contact dermatitis have appeared among nail salon workers. Common acrylate-containing products in nail salons include traditional nail polish, ultraviolet-cured shellac nail polish, ultraviolet-cured gel nails, and press-on acrylic nails. Nail salon technicians seen in the occupational medicine clinic in 2015 and 2016 were identified, and their patch test results and clinical features were summarized. Patch testing was done with the Chemotechnique (Meth)Acrylate nail series, and either the North American Standard series or the North American Contact Dermatitis Group screening series. Six patients were identified, all women, ages 38 to 58. Common presentations included erythematous dermatitis of the dorsa of the hands, palms, and forearms and fissures on the fingertips. Less common sites of eruptions included the periorbital region, cheeks, posterior ears, neck, sacral area, lateral thighs, and dorsa of the feet. All patients reacted to hydroxyethyl methacrylate, and 5 patients reacted to ethyl acrylate. Each patient also reacted to (meth)acrylates that are not found on either standard series, including ethyleneglycol dimethacrylate, 2-hydroxypropyl methacrylate, and 2-hydroxyethyl acrylate. The authors report 6 cases of allergic contact dermatitis to acrylates in nail technicians seen over the past year, representing a new trend in their clinic. These cases are reflective of a growing trend of nail technicians with allergic contact dermatitis associated with occupational (meth)acrylate exposure. Efforts to improve prevention are needed.

  5. Hybrid clear cell odontogenic carcinoma and ameloblastic ...

    African Journals Online (AJOL)

    Clear cell odontogenic carcinoma (CCOC) which was previously designated clear cell odontogenic tumor also exhibits an aggressive biologic behavior and a tendency to metastasize to distant locations. Both lesions are rare. We report an odontogenic carcinoma with a dual histomorphologic feature of CCOC and AC ...

  6. Acoustics of Clear Speech: Effect of Instruction

    Science.gov (United States)

    Lam, Jennifer; Tjaden, Kris; Wilding, Greg

    2012-01-01

    Purpose: This study investigated how different instructions for eliciting clear speech affected selected acoustic measures of speech. Method: Twelve speakers were audio-recorded reading 18 different sentences from the Assessment of Intelligibility of Dysarthric Speech (Yorkston & Beukelman, 1984). Sentences were produced in habitual, clear,…

  7. Hybrid clear cell odontogenic carcinoma and ameloblastic ...

    African Journals Online (AJOL)

    Ameloblastic carcinoma (AC) produces extensive local destruction, perforation of the cortical plate, extension into surrounding soft tissues, numerous recurrent lesions, and metastasis, usually to cervical lymph nodes. Clear cell odontogenic carcinoma (CCOC) which was previously designated clear cell odontogenic tumor ...

  8. Chemical Literature Exercises and Resources (CLEAR).

    Science.gov (United States)

    Hostettler, John D.; And Others

    These materials were developed to make the structure and use of the chemical literature clear to chemistry students and to help them become independent and intelligent users of the library. The design of Chemical Literature Exercises and Resources (CLEAR) includes a users' note and five main parts: introduction to chemical literature, chemical…

  9. 17 CFR 256.184 - Clearing accounts.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Clearing accounts. 256.184 Section 256.184 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION (CONTINUED) UNIFORM... COMPANY ACT OF 1935 4. Deferred Debits § 256.184 Clearing accounts. This account shall include...

  10. 27 CFR 9.99 - Clear Lake.

    Science.gov (United States)

    2010-04-01

    ...) Boundaries. The Clear Lake viticultural area is located in southwestern Lake County, California. The....S. maps. The maps are titled as follows: (1) “Lower Lake Quadrangle, California,” 15 minute series... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Clear Lake. 9.99 Section 9...

  11. Internalization, Clearing and Settlement, and Liquidity

    NARCIS (Netherlands)

    Degryse, H.A.; van Achter, M.; Wuyts, G.

    2012-01-01

    Abstract: We study the relation between liquidity in financial markets and post-trading fees (i.e. clearing and settlement fees). The clearing and settlement agent (CSD) faces different marginal costs for different types of transactions. Costs are lower for an internalized transaction, i.e. when

  12. 220 AUTOMATED CLEARING SYSTEM AND THE BANKING ...

    African Journals Online (AJOL)

    clearing system. The result revealed that automated clearing system has a significant positive impact on the general payment system. The paper concludes that the post NACS era is more efficient and hence we recommend the ..... Nzotta S.M. (2004) Money Banking and Finance: Theory and Practice Bon Publishers. Owerri.

  13. Clear cell carcinoma of the palate.

    Science.gov (United States)

    Grenevicki, L F; Barker, B F; Fiorella, R M; Mosby, E L

    2001-10-01

    A case of minor salivary gland clear cell adenocarcinoma of the palate with metastasis to the lungs in a 53-year-old female is presented. Histologically, the cells were characterized by glycogen rich clear cells arranged in solid nests, trabeculae, surrounded by hyalinized fibrous stroma. We believe this represents an aggressive form of this type of tumor.

  14. Adhesive retention of experimental fiber-reinforced composite, orthodontic acrylic resin, and aliphatic urethane acrylate to silicone elastomer for maxillofacial prostheses.

    Science.gov (United States)

    Kosor, Begüm Yerci; Artunç, Celal; Şahan, Heval

    2015-07-01

    A key factor of an implant-retained facial prosthesis is the success of the bonding between the substructure and the silicone elastomer. Little has been reported on the bonding of fiber reinforced composite (FRC) to silicone elastomers. Experimental FRC could be a solution for facial prostheses supported by light-activated aliphatic urethane acrylate, orthodontic acrylic resin, or commercially available FRCs. The purpose of this study was to evaluate the bonding of the experimental FRC, orthodontic acrylic resin, and light-activated aliphatic urethane acrylate to a commercially available high-temperature vulcanizing silicone elastomer. Shear and 180-degree peel bond strengths of 3 different substructures (experimental FRC, orthodontic acrylic resin, light-activated aliphatic urethane acrylate) (n=15) to a high-temperature vulcanizing maxillofacial silicone elastomer (M511) with a primer (G611) were assessed after 200 hours of accelerated artificial light-aging. The specimens were tested in a universal testing machine at a cross-head speed of 10 mm/min. Data were collected and statistically analyzed by 1-way ANOVA, followed by the Bonferroni correction and the Dunnett post hoc test (α=.05). Modes of failure were visually determined and categorized as adhesive, cohesive, or mixed and were statistically analyzed with the chi-squared goodness-of-fit test (α=.05). As the mean shear bond strength values were evaluated statistically, no difference was found among the experimental FRC, aliphatic urethane acrylate, and orthodontic acrylic resin subgroups (P>.05). The mean peel bond strengths of experimental fiber reinforced composite and aliphatic urethane acrylate were not found to be statistically different (P>.05). The mean value of the orthodontic acrylic resin subgroup peel bond strength was found to be statistically lower (P.05). Shear forces predominantly exhibited cohesive failure (64.4%), whereas peel forces predominantly exhibited adhesive failure (93.3%). The

  15. SNOW CLEARING SERVICE WINTER 2001-2002

    CERN Multimedia

    ST-HM Group; Tel. 72202

    2001-01-01

    As usual at this time of the year, the snowing clearing service, which comes under the control of the Transport Group (ST-HM), is preparing for the start of snow-clearing operations (timetable, stand-by service, personnel responsible for driving vehicles and machines, preparation of useful and necessary equipment, work instructions, etc.) in collaboration with the Cleaning Service (ST-TFM) and the Fire Brigade (TIS-FB). The main difficulty for the snow-clearing service is the car parks, which cannot be properly cleared because of the presence of CERN and private vehicles parked there overnight in different parts of the parking areas. The ST-HM Transport Group would therefore like to invite you to park vehicles together in order to facilitate the access of the snow ploughs, thus allowing the car parks to be cleared more efficiently before the personnel arrives for work in the mornings.

  16. THE IMPORTANCE OF COAGULATION BATH IN ACRYLIC FIBER PRODUCTION

    Directory of Open Access Journals (Sweden)

    İsmail TİYEK

    2005-03-01

    Full Text Available In the production of acrylic fibers using wet-spinning method, fiber formation takes places in the coagulation bath. Therefore, physical properties of the fibers, produced by the wet-spinning method, is affected by coagulation bath conditions. For this reason, coagulation bath parameters have to be checked very well. In this paper, both the physical events such as diffusion and phase transition, occured in the coagulation bath, and some coagulation bath parameters that affect these physical events are studied. Furthermore, it is tried to express their affects on the physical characteristics of the fibers.

  17. Corrigendum: Softec HD hydrophilic acrylic intraocular lens: biocompatibility and precision

    Directory of Open Access Journals (Sweden)

    Espandar L

    2011-02-01

    Full Text Available Espandar L, Sikder S, Moshirfar M. Softec HD hydrophilic acrylic intraocular lens: biocompatibility and precision. Clin Ophthalmol. 2011;5:65–70.There was an error in the reported optic size of Lenstec’s Softec HD intraocular lens, which was reported to be 5.5 mm in Espandar et al’s work, but is 5.75 mm.Please see the specifications on Lenstec’s Web site for further details (see http://www.lenstec.com/lenstec/hd_specs.html.Read the original article

  18. Primary clear cell sarcoma of rib

    Energy Technology Data Exchange (ETDEWEB)

    Hersekli, Murat Ali [Baskent University Medical Faculty, Department of Orthopedics and Traumatology, Adana (Turkey); Baskent University Medical Faculty, Adana Medical Center, Yuregir Adana (Turkey); Ozkoc, Gurkan; Akpinar, Sercan; Ozalay, Metin; Tandogan, Reha N. [Baskent University Medical Faculty, Department of Orthopedics and Traumatology, Adana (Turkey); Bircan, Sema [Suleyman Demirel University Medical Faculty, Department of Pathology, Adana (Turkey); Tuncer, Ilhan [Baskent University Medical Faculty, Department of Pathology, Adana (Turkey)

    2005-03-01

    Clear cell sarcoma (malignant melanoma of soft tissues) is a very rare soft tissue neoplasm. It generally arises in tendons and aponeuroses. Although metastasis of malignant melanoma to bone is not uncommon, primary clear cell sarcoma of bone is an extremely rare neoplasm. To our knowledge five cases have been reported in the English literature. We present a case of primary clear cell sarcoma of bone in a 28-year-old woman arising in the left ninth rib. We treated the patient with total excision of the mass and postoperative radiotherapy. The patient is alive and well without local recurrence or distant metastasis at 33 months after surgery. (orig.)

  19. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by the...

  20. Synthesis of Radiation Curable Palm Oil–Based Epoxy Acrylate: NMR and FTIR Spectroscopic Investigations

    Directory of Open Access Journals (Sweden)

    Ashraf M. Salih

    2015-08-01

    Full Text Available Over the past few decades, there has been an increasing demand for bio-based polymers and resins in industrial applications, due to their potential lower cost and environmental impact compared with petroleum-based counterparts. The present research concerns the synthesis of epoxidized palm oil acrylate (EPOLA from an epoxidized palm oil product (EPOP as environmentally friendly material. EPOP was acrylated by acrylic acid via a ring opening reaction. The kinetics of the acrylation reaction were monitored throughout the reaction course and the acid value of the reaction mixture reached 10 mg KOH/g after 16 h, indicating the consumption of the acrylic acid. The obtained epoxy acrylate was investigated intensively by means of FTIR and NMR spectroscopy, and the results revealed that the ring opening reaction was completed successfully with an acrylation yield about 82%. The UV free radical polymerization of EPOLA was carried out using two types of photoinitiators. The radiation curing behavior was determined by following the conversion of the acrylate groups. The cross-linking density and the hardness of the cured EPOLA films were measured to evaluate the effect of the photoinitiator on the solid film characteristics, besides, the thermal and mechanical properties were also evaluated.

  1. Contact dermatitis from acrylate and methacrylate compounds in Lowicryl embedding media for electron microscopy.

    Science.gov (United States)

    Tobler, M; Wüthrich, B; Freiburghaus, A U

    1990-08-01

    This report is about occupational contact dermatitis found in 3 out of 6 workers of a chemistry laboratory using Lowicryl embedding media, which contain (meth)acrylate monomer mixtures of known composition. The notation (meth)acrylates is used to refer to both acrylates and methacrylates. (Meth)acrylate monomers will polymerize in the absence of oxygen when induced by metal ions, peroxides, heat or ultraviolet light. The monomers are of low viscosity and remain in the liquid state at temperatures far below 0 degree C. The volatile compounds, some of which exhibit a most pungent odour, have a tendency to penetrate all tissue and to permeate into the finest fissures, a property which makes them suitable as sealants, glues, embedding material, etc. This and their toxicity may represent a danger to the health of individuals who need to work with them, especially if no precautions are taken. We show with patch testing that one patient reacted strongly to the compound 2-hydroxyethyl acrylate at the dilutions tested (0.5 and 1% v/v), but not at all to 10 other (meth)acrylates. In the same test, 3 volunteer controls were negative to 2-hydroxyethyl acrylate. We demonstrate that at maximum working concentration, 2-hydroxyethyl acrylate penetrates both latex and vinyl gloves and elicits irritant/allergic reactions on the patient and irritant reactions on a control. Finally, we discuss the necessary protective measures.

  2. Lactate and acrylate metabolism by Megasphaera elsdenii under batch and steady-state conditions.

    Science.gov (United States)

    Prabhu, Rupal; Altman, Elliot; Eiteman, Mark A

    2012-12-01

    The growth of Megasphaera elsdenii on lactate with acrylate and acrylate analogues was studied under batch and steady-state conditions. Under batch conditions, lactate was converted to acetate and propionate, and acrylate was converted into propionate. Acrylate analogues 2-methyl propenoate and 3-butenoate containing a terminal double bond were similarly converted into their respective saturated acids (isobutyrate and butyrate), while crotonate and lactate analogues 3-hydroxybutyrate and (R)-2-hydroxybutyrate were not metabolized. Under carbon-limited steady-state conditions, lactate was converted to acetate and butyrate with no propionate formed. As the acrylate concentration in the feed was increased, butyrate and hydrogen formation decreased and propionate was increasingly generated, while the calculated ATP yield was unchanged. M. elsdenii metabolism differs substantially under batch and steady-state conditions. The results support the conclusion that propionate is not formed during lactate-limited steady-state growth because of the absence of this substrate to drive the formation of lactyl coenzyme A (CoA) via propionyl-CoA transferase. Acrylate and acrylate analogues are reduced under both batch and steady-state growth conditions after first being converted to thioesters via propionyl-CoA transferase. Our findings demonstrate the central role that CoA transferase activity plays in the utilization of acids by M. elsdenii and allows us to propose a modified acrylate pathway for M. elsdenii.

  3. Synthesis of Radiation Curable Palm Oil-Based Epoxy Acrylate: NMR and FTIR Spectroscopic Investigations.

    Science.gov (United States)

    Salih, Ashraf M; Ahmad, Mansor Bin; Ibrahim, Nor Azowa; Dahlan, Khairul Zaman Hj Mohd; Tajau, Rida; Mahmood, Mohd Hilmi; Yunus, Wan Md Zin Wan

    2015-08-04

    Over the past few decades, there has been an increasing demand for bio-based polymers and resins in industrial applications, due to their potential lower cost and environmental impact compared with petroleum-based counterparts. The present research concerns the synthesis of epoxidized palm oil acrylate (EPOLA) from an epoxidized palm oil product (EPOP) as environmentally friendly material. EPOP was acrylated by acrylic acid via a ring opening reaction. The kinetics of the acrylation reaction were monitored throughout the reaction course and the acid value of the reaction mixture reached 10 mg KOH/g after 16 h, indicating the consumption of the acrylic acid. The obtained epoxy acrylate was investigated intensively by means of FTIR and NMR spectroscopy, and the results revealed that the ring opening reaction was completed successfully with an acrylation yield about 82%. The UV free radical polymerization of EPOLA was carried out using two types of photoinitiators. The radiation curing behavior was determined by following the conversion of the acrylate groups. The cross-linking density and the hardness of the cured EPOLA films were measured to evaluate the effect of the photoinitiator on the solid film characteristics, besides, the thermal and mechanical properties were also evaluated.

  4. Enzyme-Catalyzed Synthesis of Saccharide Acrylate Monomers from Nonedible Biomass

    NARCIS (Netherlands)

    Kloosterman, Wouter M. J.; Brouwer, Sander; Loos, Katja

    Various cellulase preparations were found to catalyze the transglycosidation between cotton linters and 2-hydroxyethyl acrylate. The conversion and enzyme activity were found to be optimal in reaction mixtures that contained 5 vol% of the acrylate. The structures of the products were revealed by

  5. Cleavage of dimethylsulfoniopropionate and reduction of acrylate by Desulfovibrio acrylicus sp nov

    NARCIS (Netherlands)

    van der Maarel, M.J.E.C.; vanBergeijk, S; van Werkhoven, A.F.; Laverman, AM; Meijer, W.G.; Stam, W.T.; Hansen, T.A.

    From anoxic intertidal sediment, a dimethylsulfoniopropionate (DMSP)-cleaving anaerobe (strain W218) was isolated that reduced the acrylate formed to propionate. The bacterium was vibrio- to rod-shaped and motile by means of multiple polar flagella. It reduced sulfate, thiosulfate, and acrylate, and

  6. Use of an acrylic mold for mortise view improvement in ankle fractures: a feasibility study

    NARCIS (Netherlands)

    Donken, C.C.M.A.; Verhofstad, M.H.J.; Edwards, M.J.R.; Schoemaker, M.C.; Laarhoven, C.J.H.M. van

    2011-01-01

    We investigated an acrylic mold for use in obtaining ankle radiographs in 31 consecutive patients with ankle fracture. The radiologic examination consisted of routine lateral and mortise views, with the same views procured with the use of the acrylic mold to position the ankle. Radiographic evidence

  7. 21 CFR 177.2000 - Vinylidene chloride/methyl acrylate/methyl methacrylate polymers.

    Science.gov (United States)

    2010-04-01

    ... methacrylate polymers. 177.2000 Section 177.2000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF...: POLYMERS Substances for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.2000 Vinylidene chloride/methyl acrylate/methyl methacrylate polymers. The vinylidene chloride/methyl acrylate...

  8. Heat-cured Acrylic Resin versus Light-activated Resin: A Patient ...

    African Journals Online (AJOL)

    Context: Although light-activated resins (Eclipse) have been reported to possess superior physical and mechanical properties compared with the heat-cured acrylic resins (Lucitone-199), a few studies have compared overdentures with a locator attachment constructed from heat-cured acrylic resins with those constructed ...

  9. Biocatalytic Synthesis of Maltodextrin-Based Acrylates from Starch and alpha-Cyclodextrin

    NARCIS (Netherlands)

    Kloosterman, Wouter M. J.; Spoelstra-van Dijk, Gerda; Loos, Katja

    Novel 2-(beta-maltooligooxy)-ethyl (meth) acrylate monomers are successfully synthesized by CGTase from Bacillus macerans catalyzed coupling of 2-(beta-glucosyloxy)-ethyl acrylate and methacrylate with a-cyclodextrin or starch. HPLC-UV analysis shows that the CGTase catalyzed reaction yields

  10. Implantation of porous acrylic cement in soft tissues: An animal and human biopsy histological study

    NARCIS (Netherlands)

    P.J. van Mullem (P.); J.M. Vaandrager (Michiel); J.P.A. Nicolai (Jean); J.R. de Wijn (J.)

    1990-01-01

    markdownabstractAbstract Long-term (8 and 24 month) reactions of the (hypo) dermis of the guinea pig to solid and porous (50 vol%) acrylic implants and four human biopsies from porous subcutaneous acrylic implants were studied light microscopically. The solid implants were encapsulated by dense

  11. Neutral, anionic, cationic, and zwitterionic diblock copolymers featuring poly(2-methoxyethyl acrylate) hydrophobic segments

    DEFF Research Database (Denmark)

    Javakhishvili, Irakli; Jankova Atanasova, Katja; Hvilsted, Søren

    2013-01-01

    ), and zwitterionic poly(3-(N-(2-methacryloyloxyethyl)-N,N- dimethylammonio)propane sulfonate) (PDMAPS) blocks are constructed. mPEG, poly(tert-butyl acrylate) (PtBA), and poly(tert-butyl methacrylate) (PtBMA) macroinitiators are chain extended with 2-methoxyethyl acrylate (MEA) employing copper-mediated atom...

  12. Formation of Methyl Acrylate from CO 2 and Ethylene via Methylation of Nickelalactones

    KAUST Repository

    Bruckmeier, Christian

    2010-05-24

    The nickel-induced coupling of ethylene and CO2 represents a promising pathway toward acrylates. To overcome the high bond dissociation energies of the M-O moieties, we worked out an in situ methylation of nickelalactones to realize the β-hydride elimination and the liberation of the acrylate species. © 2010 American Chemical Society.

  13. High Altitude Clear Air Turbulence Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Air Force Flight Dynamics Laboratory conducted the High Altitude Clear Air Turbulence Project in the mid 1960s with the intention of better understanding air...

  14. Clear corneal incision in cataract surgery.

    Science.gov (United States)

    Al Mahmood, Ammar M; Al-Swailem, Samar A; Behrens, Ashley

    2014-01-01

    Since the introduction of sutureless clear corneal cataract incisions, the procedure has gained increasing popularity worldwide because it offers several advantages over the traditional sutured scleral tunnels and limbal incisions. Some of these benefits include lack of conjunctival trauma, less discomfort and bleeding, absence of suture-induced astigmatism, and faster visual rehabilitation. However, an increasing incidence of postoperative endophthalmitis after clear corneal cataract surgery has been reported. Different authors have shown a significant increase up to 15-fold in the incidence of endophthalmitis following clear corneal incision compared to scleral tunnels. The aim of this report is to review the advantages and disadvantages of clear corneal incisions in cataract surgery, emphasizing on wound construction recommendations based on published literature.

  15. Clear-cell chondrosarcoma of the humerus

    OpenAIRE

    Elojeimy, Saeed; Ahrens, William A.; Howard, Brian; Patt, Joshua C.; Stone, Taylor; Kneisl, Jeffrey S.; Bhargava, Puneet

    2015-01-01

    Clear-cell chondrosarcoma is a rare, low-grade variant of chondrosarcoma characterized by slow growth, low metastatic potential, and a predilection for local recurrence long after treatment. We report an unusually aggressive case of clear-cell chondrosarcoma of the humerus with early metastasis to multiple bony sites including femur, thoracic and lumbar spine, sacrum, and iliac bone. Our purpose is to alert physicians to the sarcoma's potential for aggressive behavior, necessitating closer an...

  16. CO2 efflux from cleared mangrove peat.

    Directory of Open Access Journals (Sweden)

    Catherine E Lovelock

    Full Text Available BACKGROUND: CO(2 emissions from cleared mangrove areas may be substantial, increasing the costs of continued losses of these ecosystems, particularly in mangroves that have highly organic soils. METHODOLOGY/PRINCIPAL FINDINGS: We measured CO(2 efflux from mangrove soils that had been cleared for up to 20 years on the islands of Twin Cays, Belize. We also disturbed these cleared peat soils to assess what disturbance of soils after clearing may have on CO(2 efflux. CO(2 efflux from soils declines from time of clearing from ∼10,600 tonnes km(-2 year(-1 in the first year to 3000 tonnes km(2 year(-1 after 20 years since clearing. Disturbing peat leads to short term increases in CO(2 efflux (27 umol m(-2 s(-1, but this had returned to baseline levels within 2 days. CONCLUSIONS/SIGNIFICANCE: Deforesting mangroves that grow on peat soils results in CO(2 emissions that are comparable to rates estimated for peat collapse in other tropical ecosystems. Preventing deforestation presents an opportunity for countries to benefit from carbon payments for preservation of threatened carbon stocks.

  17. Characteristics and mechanisms of acrylate polymer damage to maize seedlings.

    Science.gov (United States)

    Chen, Xian; Mao, Xiaoyun; Lu, Qin; Liao, Zongwen; He, Zhenli

    2016-07-01

    Superabsorbent acrylate polymers (SAPs) have been widely used to maintain soil moisture in agricultural management, but they may cause damage to plants, and the mechanisms are not well understood. In this study, seed germination, soil pot culture, hydroponic experiments, and SAPs degradation were conducted to investigate damage characteristics and mechanisms associated with SAPs application. The Results showed that SAPs inhibited maize growth and altered root morphology (irregular and loose arrangement of cells and breakage of cortex parenchyma), and the inhibitory effects were enhanced at higher SAPs rates. After 1h SAP hydrogels treatment, root malondialdehyde (MDA) content was significantly increased, while superoxide dismutase (SOD) and catalase (CAT) content were significantly decreased. Hydroponics experiment indicated that root and shoot growth was inhibited at 2.5mgL(-1) acrylic acid (AA), and the inhibition was enhanced with increasing AA rates. This effect was exacerbated by the presence of Na(+) at a high concentration in the hydrogels. Release and degradation of AA were enhanced at higher soil moisture levels. A complete degradation of AA occurred between 15 and 20 days after incubation (DAI), but it took longer for Na(+) concentration to decrease to a safe level. These results indicate that high concentration of both AA and Na(+) present in the SAPs inhibits plant growth. The finding of this study may provide a guideline for appropriate application of SAPs in agriculture. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. Color difference threshold determination for acrylic denture base resins.

    Science.gov (United States)

    Ren, Jiabao; Lin, Hong; Huang, Qingmei; Liang, Qifan; Zheng, Gang

    2015-01-01

    This study aimed to set evaluation indicators, i.e., perceptibility and acceptability color difference thresholds, of color stability for acrylic denture base resins for a spectrophotometric assessing method, which offered an alternative to the visual method described in ISO 20795-1:2013. A total of 291 disk specimens 50±1 mm in diameter and 0.5±0.1 mm thick were prepared (ISO 20795-1:2013) and processed through radiation tests in an accelerated aging chamber (ISO 7491:2000) for increasing times of 0 to 42 hours. Color alterations were measured with a spectrophotometer and evaluated using the CIE L*a*b* colorimetric system. Color differences were calculated through the CIEDE2000 color difference formula. Thirty-two dental professionals without color vision deficiencies completed perceptibility and acceptability assessments under controlled conditions in vitro. An S-curve fitting procedure was used to analyze the 50:50% perceptibility and acceptability thresholds. Furthermore, perceptibility and acceptability against the differences of the three color attributes, lightness, chroma, and hue, were also investigated. According to the S-curve fitting procedure, the 50:50% perceptibility threshold was 1.71ΔE00 (r(2)=0.88) and the 50:50% acceptability threshold was 4.00 ΔE00 (r(2)=0.89). Within the limitations of this study, 1.71/4.00 ΔE00 could be used as perceptibility/acceptability thresholds for acrylic denture base resins.

  19. Prevention of allergy to acrylates and latex in dental personnel.

    Science.gov (United States)

    Ohlson, Carl-Göran; Svensson, Lisbeth

    2002-01-01

    Contact allergy to acrylate monomers and immediate hypersensitivity to latex gloves in dental personnel calls for preventive measures to reduce the risks. The aim of the study was to evaluate the preventive effect of an information campaign after a 3-year follow-up. The campaign included instructions and training according to an ordinance, both in writing and orally, e.g. concerning the choice of products and protection devices and the proper handling of the materials. The follow-up was carried out through 1997-2000 and included all eligible 513 subjects. Information on new cases was ascertained by a questionnaire and reports from the occupational health service and the department of dermatology. The number of expected new cases was based on the incidence rate, derived from a preceding prevalence study in the same county, and the exposed years at risk in the follow-up period. No new case of allergy to acrylates or latex rubber was found in the follow-up period as against 4.91 expected (p = 0.007). In conclusion, this study indicates that occupational allergies can be prevented successfully, but requires vigorous measures to influence the behaviour and the routines of daily work in dental practice.

  20. Effect of disinfectant solutions on a denture base acrylic resin.

    Science.gov (United States)

    Carvalho, Cristiane F; Vanderlei, Aleska D; Marocho, Susana M Salazar; Pereira, Sarina M B; Nogueira, Lafayette; Paes-Júnior, Tarcisio J Arruda

    2012-01-01

    The aim of this study was to evaluate the hardness, roughness and mass loss of an acrylic denture base resin after in vitro exposure to four disinfectant solutions. Forty specimens (Clássico, Brazil) were prepared and randomly assigned to 4 groups n = 10) according to the disinfectant solution: G1: control, stored in distilled water at 37 degrees C; G2: 1% sodium hypochlorite; G3: 2% glutaraldehyde; G4: 4% chlorhexidine. G2 to G4 were immersed for 60 minutes in the disinfectant solution. Measurements were carried out both before and after immersion in the solution. The surface was analyzed with a surface roughness tester (Surfcorder SE 1700 KOZAKALAB), a microdurometer FM-700 (Future Tech) and a scanning electron microscope (DSM 962-ZEISS). Loss of mass was determined with a digital weighing scale. After disinfection procedures, values were analyzed statistically. The acrylic denture base resin may be vulnerable to surface changes after in vitro immersion in the disinfectant solutions studied.

  1. The transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion

    Directory of Open Access Journals (Sweden)

    Devi Rianti

    2006-12-01

    Full Text Available A laboratoric experimental study was conducted on the transverse strength of acrylic resin after Coleus amboinicus, Lour extract solution immersion. The aim of this study is to know the difference of acrylic resin transverse strengths caused by immersion time variations in a concentrate solution. The study was carried out on unpolished acrylic resin plates with 65 × 10 × 2,5 mm dimension; solution with 15% Coleus amboinicus, Lour extract, and 30, 60, 90 days immersion times to measure the transverse strength and sterilized aquadest was used as control. Acrylic resin plates transverse strength was measured using Autograph AG-10 TE. The data was analyzed using One-Way Anova and LSD with 5% degree of significance. The result showed that longer immersion time will decrease the transverse strength of the acrylic resin plates. After 90 days immersion time, the transverse strength decrease is still above the recommended standard transverse strength.

  2. Thin film of Poly(acrylic acid-co-allyl acrylate as a Sacrificial Protective Layer for Hydrophilic Self Cleaning Glass

    Directory of Open Access Journals (Sweden)

    Jānis Lejnieks

    2010-05-01

    Full Text Available Poly(acrylic acid-co-allyl acrylate statistical copolymers were synthesized in a controlled manner in two steps: first tert.butyl acrylate and allyl acrylate were polymerized via atom transfer radical polymerization (ATRP and afterwords the tert.butyl protective groups were removed via hydrolysis. Samples of self cleaning glass (SCG were coated with thin films of poly(acrylic acid-co-allyl acrylate and cross-linked afterwards by UV irradiation (in the presence of a photoinitiator and an accelerator. Solution cast thin films were transparent and homogeneous before and after UV cross-linking. The irradiated samples were found to be hydrophilic (Θ < 20° and water insoluble. The coating prevented the spontaneous hydrophobization of the SCG by residual silicon exhaled from the sealing material. The TiO2 photocatalyst that covers the glass surface was found to strip the protective coating. The rate of the photooxidation process was measured by IR spectroscopy. The real field performance of the protective coating was also tested.

  3. Nd:YAG capsulotomy rates after use of the AcrySof acrylic three piece and one piece intraocular lenses

    OpenAIRE

    Mian, S I; Fahim, K; Marcovitch, A; Gada, H; Musch, D C; Sugar, A

    2005-01-01

    Background/aim: Acrylic lens size and shape may influence the rate of posterior capsule opacification (PCO) and need for Nd:YAG capsulotomy. The aim of this study is to compare the Nd:YAG capsulotomy rate of the three piece acrylic/PMMA AcrySof MA series lens with the one piece acrylic AcrySof SA series lens.

  4. Effect of pressure and polishing technique on surface roughness of cold cured acrylic resin

    Directory of Open Access Journals (Sweden)

    Sianiwati Goenharto

    2007-06-01

    Full Text Available The smoothness of acrylic surface plays an important role in producing removable orthodontic appliances. Int this study, we examine the effect of pressure and polishing technique on surface roughness of cold cured acrylic resin. Forty eight samples were prepared and classified into two groups: acrylic resin polymerization with and without pressure. Each group was classified into four subgroups: being polished with abrasive stone, bur for acrylic, silicone polisher and without being polished as control group. Surface roughness was measured using surface roughness tester. The surface roughness of polymerized acrylic with and without pressure and polished with different technique was analyzed using One-Way ANOVA, continued by Dunnet test. T-test was done to know whether there was the effect of pressure on surface roughness after being polished using certain technique. The result showed that pressure and polishing technique affected surface roughness significantly (p = 0.001. On the group of polymerization with pressure, surface roughness resulted from polishing with bur of acrylic showed significant difference with silicone polisher, whereas on the group without pressure, polishing with bur of acrylic showed significant difference with abrasive stone. Of the three polishing techniques, there was significant difference of surface roughness of cold cured acrylic resin (t = 0.002. It is concluded that pressure and polishing technique affected the surface roughness of cold cured acrylic resin. Polishing technique using bur of acrylic, followed by abrasive paper, rotating felt cone and soft brush showed less surface roughness on the group of polymerization with or without pressure.

  5. Enzyme-catalyzed synthesis of saccharide acrylate monomers from nonedible biomass.

    Science.gov (United States)

    Kloosterman, Wouter M J; Brouwer, Sander G M; Loos, Katja

    2014-08-01

    Various cellulase preparations were found to catalyze the transglycosidation between cotton linters and 2-hydroxyethyl acrylate. The conversion and enzyme activity were found to be optimal in reaction mixtures that contained 5 vol % of the acrylate. The structures of the products were revealed by using TLC and (1) H and (13) C NMR spectroscopy. The enzyme-catalyzed reaction resulted in two products. The minor product originated from transglycosidation to hemicellulose and was found to be 2-(β-xylosyloxy)-ethyl acrylate. The major product was identified as 2-(β-glucosyloxy)-ethyl acrylate and the yield of the product was 5 wt % based on the amount of consumed cellulose. Glycosidation products with oligosaccharide moieties could not be detected in the reaction mixture. This result can be explained by the hydrolytic activities of the used cellulase preparation. Cellulase from Trichoderma reesei was found to possess, in addition to endoglucanase activity, cellobiosidase and β-glucosidase activities. Five other cellulase preparations from different origins were tested as well for catalysis of oligosaccharide acrylate synthesis. For most cellulase preparations the major transglycosidation product appeared to be 2-(β-glucosyloxy)-ethyl acrylate. Nevertheless, the endo-β-(1,4)-glucanase from Trichoderma longibrachiatum was found to catalyze the synthesis of 2-(β-cellobiosyloxy)-ethyl acrylate. Unlike the other cellulase preparations, endo-β-(1,4)-glucanase from T. longibrachiatum showed no detectable β-glucosidase activity and therefore oligosaccharide acrylate monomers were not further hydrolyzed into the monosaccharide acrylate 2-(β-glucosyloxy)-ethyl acrylate. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Optical clearing: impact of optical and dielectric properties of clearing solutions on pulmonary tissue mechanics.

    Science.gov (United States)

    Schwenninger, David; Priebe, Hans-Joachim; Schneider, Matthias; Runck, Hanna; Guttmann, Josef

    2017-07-01

    Optical clearing allows tissue visualization under preservation of organ integrity. Optical clearing of organs with a physiological change in three-dimensional geometry (such as the lung) would additionally allow visualization of macroscopic and microscopic tissue geometry. A prerequisite, however, is the preservation of the native tissue mechanics of the optically cleared lung tissue. We investigated the impact of optical and dielectric properties of clearing solutions on biomechanics and clearing potency in porcine tissue strips of healthy lungs. After fixation, bleaching, and rehydration, four methods of optical clearing were investigated using eight different protocols. The mechanical and optical properties of the cleared lung tissue strips were investigated by uniaxial tensile testing and by analyzing optical transparency and translucency for red, green, and blue light before, during, and after the biochemical optical clearing process. Fresh tissue strips were used as controls. Best balance between efficient clearing and preserved mechanics was found for clearing with a 1:1 mixture of dimethyl sulfoxide (DMSO) and aniline. Our findings show that 1) the degree of tissue transparency and translucency correlated with the refractive index of the clearing solution index (r = 0.976, P = 0.0004; and r = 0.91, P = 0.0046, respectively), 2) tissue mechanics were affected by dehydration and the type of clearing solution, and 3) tissue biomechanics and geometry correlated with the dielectric constant of the clearing solution (r = -0.98, P dielectric constant of the clearing solutions, the larger the effect on tissue stiffness. This suggests that the dielectric constant is an important measure in determining the effect of a clearing solution on lung tissue biomechanics. Optimal tissue transparency requires complete tissue dehydration and a refractive index of 1.55 of the clearing solution.NEW & NOTEWORTHY Investigating optical clearing in porcine lung tissue strips, we

  7. 76 FR 47529 - Customer Clearing Documentation and Timing of Acceptance for Clearing; Correction

    Science.gov (United States)

    2011-08-05

    ... From the Federal Register Online via the Government Publishing Office COMMODITY FUTURES TRADING COMMISSION 17 CFR Parts 1, 23, and 39 RIN 3038-AD51 Customer Clearing Documentation and Timing of Acceptance... August 1, 2011, regarding Customer Clearing Documentation and Timing of Acceptance for Clearing. FOR...

  8. Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

    Directory of Open Access Journals (Sweden)

    Keslarek Amauri José

    2004-01-01

    Full Text Available Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM. Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the particles, while S is uniformly distributed within then. The Na and N elemental maps show that the respective monovalent ions (Na+ and NH4+ have different distributions, in the latex: Na signal within the particles is stronger than in the background, while N is accumulated at the particle borders. The distributions of surfactant and counter-ions are thus different from some current assumptions, but they support recent results on the distribution of ionic constituents in latex films, by scanning electric potential microscopy.

  9. Synthesis of Highly Porous Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) Asymmetric Membranes

    KAUST Repository

    Xie, Yihui

    2016-03-24

    For the first time, self-assembly and non-solvent induced phase separation was applied to polysulfone-based linear block copolymers, reaching mechanical stability much higher than other block copolymers membranes used in this method, which were mainly based on polystyrene blocks. Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) (PtBA30k-b-PSU14k-b-PtBA30k) with a low polydispersity of 1.4 was synthesized by combining step-growth condensation and RAFT polymerization. Various advanced electron microscopies revealed that PtBA30k-b-PSU14k-b-PtBA30k assembles into worm-like cylindrical micelles in DMAc and adopts a “flower-like” arrangement with the PSU central block forming the shell. Computational modeling described the mechanism of micelle formation and morphological transition. Asymmetric nanostructured membranes were obtained with a highly porous interconnected skin layer and a sublayer with finger-like macrovoids. Ultrafiltration tests confirmed a water permeance of 555 L m-2 h-1 bar-1 with molecular weight cut-off of 28 kg/mol. PtBA segments on the membrane surface were then hydrolyzed and complexed with metals, leading to cross-linking and enhancement of antibacterial capability.

  10. Improved biotribological properties of PEEK by photo-induced graft polymerization of acrylic acid.

    Science.gov (United States)

    Zhao, Xiaoduo; Xiong, Dangsheng; Wang, Kun; Wang, Nan

    2017-06-01

    The keys of biomaterials application in artificial joints are good hydrophilicity and wear resistance. One kind of the potential bio-implant materials is polyetheretherketone (PEEK), which has some excellent properties such as non-toxic and good biocompatibility. However, its bioinert surface and inherent chemical inertness hinder its application. In this study, we reported an efficient method for improving the surface wettability and wear resistance for PEEK, a layer of acrylic acid (AA) polymer brushes on PEEK surface was prepared by UV-initiated graft polymerization. The effects of different grafting parameters (UV-irradiation time/AA monomer solution concentration) on surface characteristics were clearly investigated, and the AA-g-PEEK specimens were examined by ATR-FTIR, static water contact angle measurements and friction tests. Our results reveal that AA can be successfully grafted onto the PEEK surface after UV irradiation, the water wettability and tribological properties of AA-g-PEEK are much better than untreated PEEK because that AA is a hydrophilic monomer, the AA layer on PEEK surface can improve its bearing capacity and reduce abrasion. This detailed understanding of the grafting parameters allows us to accurately control the experimental products, and this method of surface modification broadens the use of PEEK in orthopedic implants. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Clear plastic cups: a childhood choking hazard.

    Science.gov (United States)

    Weiss, R L; Goldstein, M N; Dharia, A; Zahtz, G; Abramson, A L; Patel, M

    1996-11-01

    The disposable plastic beverage cup is not usually regarded as hazardous to young children. Certain varieties of these products however, are manufactured from a brittle, clear plastic that easily cracks and fragments. While most conscientious parents keep their children safe from peanuts, balloons, and other known choking hazards, a child can surreptitiously bite a cup edge and aspirate the fragment. We report two cases of foreign body aspiration involving clear plastic cups that went undetected one of which remained 21 months following a negative rigid bronchoscopy. Diagnostic difficulties are related to the transparency and radiolucency of these objects. When suspicious of foreign body aspiration in children, otolaryngologists should inquire about the availability of clear plastic cups in the household and be mindful of the diagnostic pitfalls. Further investigations including CT scanning and repeat bronchoscopy may be helpful in cases of suspected missed foreign bodies. An educational campaign aimed at prevention and placement of product package warning labels should be established.

  12. Designed drug-release systems having various breathable polyurethane film-backed hydrocolloid acrylated adhesive layers for moisture healing.

    Science.gov (United States)

    Chang, Ching-Hsien; Liu, Hsia-Wei; Huang, Ching-Cheng

    2014-01-01

    A series of designed drug-release systems were prepared and established for clear moisture healing. These systems were designed to have an interpenetrating polymer network (IPN) structure, which contained a breathable polyurethane film, hydrocolloidlayer, and polyacrylate adhesive layer. Breathable polyurethane film (2000 g/m(2)/24 hr) with high moisture permeability was employed as a base for new drug-release systems or wound dressings. All drug-release systems having a polyurethane film-backed hydrocolloid acrylated adhesive layer showed an increase of water uptakes with increasing time. After 114 hours, high water uptakes of drug-release systems with 20% hydrocolloid components were observed in the values of 160, 1100, and 1870% for different additional hydrocolloid components of carboxymethylcellulose, sodium alginate, and carbomer U10, respectively. New drug-release systems of polyurethane film-backed hydrocolloid/adhesive layers could be designed and established for wound care managements.

  13. A study on the swelling behavior of poly(acrylic acid) hydrogels obtained by electron beam crosslinking

    Energy Technology Data Exchange (ETDEWEB)

    Sheikh, N., E-mail: nasheikh@aeoi.org.i [Radiation Applications Research School, Nuclear Science and Technology Research Institute, P.O. Box 11365-3486, Tehran (Iran, Islamic Republic of); Jalili, L. [Polymer group, Technology and Engineering Department, Yazd University, Yazd (Iran, Islamic Republic of); Anvari, F. [Radiation Applications Research School, Nuclear Science and Technology Research Institute, Yazd (Iran, Islamic Republic of)

    2010-06-15

    Poly(acrylic acid) (PAA) hydrogels were prepared by using electron beam (EB) crosslinking of PAA homopolymer from its aqueous solutions. The swelling behavior of the hydrogels was studied as a function of the concentration of PAA solution, radiation dose, pH of the swelling medium and swelling time. Also the environmental pH effect on the water diffusion mode into hydrogels was investigated. These hydrogels clearly showed pH-sensitive swelling behavior with Fickian type of diffusion in the stomach-like pH medium (pH 1.3) and non-Fickian type in the intestine-like pH medium (pH 6.8).

  14. Protective effects of soft acrylic yellow filter against blue light-induced retinal damage in rats.

    Science.gov (United States)

    Tanito, Masaki; Kaidzu, Sachiko; Anderson, Robert E

    2006-12-01

    Recently, a yellow intraocular lens (IOL) was developed for the purpose of reducing potential blue light-induced retinal damage after cataract surgery. However, the effect of yellow filters on retinal protection remains to be clarified. To test the protective effects of yellow filters on blue light-induced retinal damage, a yellow and a clear soft acrylic filter were attached to the right and left eyes, respectively, of albino rats and exposed to 4.5 k lux blue fluorescent lights with peak wavelength at 420 nm (ranging 380-500 nm; short blue) or 446 nm (ranging 400-540 nm; long blue) for 6h. To assess retinal damage, the electroretinogram (ERG) was recorded at 7 days, outer nuclear layer (ONL) thickness and area were measured at 7 days, apoptosis was analyzed by TUNEL staining at 24 h, and the level of lipid peroxidation in retinas was assessed by Western dot blots using specific antibodies against 4-hydroxynonenal (4-HNE)- and carboxyethylpyrrole (CEP)-modified proteins immediately after light exposure. After short blue light exposure, a- and b-wave ERG amplitudes and the ONL thickness at 1-2.5 mm inferior and 0.5-2.5 mm superior to optic nerve head (ONH) were significantly reduced. TUNEL staining in the ONL at 0-2 mm inferior and 1-2 mm superior to the ONH, and retinal levels of 4-HNE- and CEP-modified proteins were significantly increased in the clear filter-covered eyes compared to yellow filter-covered eyes. After long blue light exposure, the only difference seen was a greater ONL thickness at 1.5 mm superior to the ONH in yellow filter-covered eye. Transmission of light through the yellow filter was 58% for short blue and 89% for long blue compared to the clear filter. The ONL area was not different between clear filter-covered and -uncovered eyes after exposure to short or long blue light. Given the results, yellow IOL material protects the retina against acute shorter wavelength blue light exposure more effectively than the clear IOL material.

  15. Lake Mead--clear and vital

    Science.gov (United States)

    Wessells, Stephen M.; Rosen, Michael

    2013-01-01

    “Lake Mead – Clear and Vital” is a 13 minute documentary relating the crucial role of science in maintaining high water quality in Lake Mead. The program was produced coincident with release of the Lakes Mead and Mohave Circular a USGS publication covering past and on-going research in the lakes and tributaries of the Lake Mead National Recreation Area.

  16. Plant Histology: Clearing and the Optical Section.

    Science.gov (United States)

    Freeman, H. E.

    1985-01-01

    Clearing is a simple and rapid technique in which 75 percent lactic acid is used to remove pigments and cytoplasmic contents of fresh leaves, enabling microscopic view of various internal leaf layers. Procedures for using the technique (which helps students gain a more thorough understanding of plant anatomy) are given. (DH)

  17. EGGS: CLEARING THE CHARGES, EXPLORING THE POTENTIAL ...

    African Journals Online (AJOL)

    0655711075

    EGGS: CLEARING THE CHARGES, EXPLORING THE POTENTIAL! Of all the different kinds of foods, an egg is special for its combination of all essential food nutrients in one item. Chicken eggs have an average weight of (~50g) with two distinct parts that have distinct nutritional values: the yolk (17g); and white (33g).

  18. CLARINO Resources: Lisence clearance and clearing ownership

    OpenAIRE

    Lyse, Gunn Inger; Gjesdal, Anje Müller

    2014-01-01

    Presentation held at a CLARINO meeting at the University of Bergen, 08.05.13 The presentation outlines the relationship between CLARIN and CLARINO, introduces basic IPR and licensing concepts, presents relevant license models and templates (e.g. Creative Commons, CLARIN licenses), presents guidelines for clearing ownership and for choosing a license. CLARINO

  19. A case of clear cell sarcoma

    DEFF Research Database (Denmark)

    Juel, Jacob; Ibrahim, Rami Mossad

    2017-01-01

    INTRODUCTION: Clear cell sarcoma (CCS) is a rare tumour of the soft tissue often misdiagnosed, as it shares characteristics with malignant melanoma (MM). Previously, CCS has been characterised, as malignant melanoma of the soft tissue, contemporary immunohistochemical techniques, however, have ma...

  20. Borderline Clear Cell Adenofibroma of the Ovary

    Directory of Open Access Journals (Sweden)

    Pilaiwan Kleebkaow

    2017-01-01

    Full Text Available Borderline clear cell tumors are extremely rare, and few cases have been reported in the literature. Herein, we present a case of borderline clear cell adenofibroma of the ovary in a 58-year-old woman who presented with a pelvic mass and constipation. Physical examination revealed a 10 cm solid midline pelvic mass. Computed tomography showed an 8 cm heterogeneous enhancing mass attached to the left posterolateral wall of the uterus. The patient’s serum CA 125 levels were slightly elevated (80.9 U/ml. The patient was given a total abdominal hysterectomy with bilateral salpingooophorectomy. On gross examination, it was found that the left ovarian tumor was an 8.0 × 7.5 × 8.0 cm solid multilobulated mass containing tiny cysts. Histologically, the tumor was composed of small glands in dense fibrous and myxoid stroma. The glands were lined with cuboidal cells with clear cytoplasm and mild to moderate nuclear atypia. No stromal invasion was observed. The pathological diagnosis was borderline clear cell adenofibroma of the left ovary. There was no reoccurrence 36 months post operation.

  1. An ORMOSIL-Containing Orthodontic Acrylic Resin with Concomitant Improvements in Antimicrobial and Fracture Toughness Properties

    Science.gov (United States)

    Rueggeberg, Frederick A.; Niu, Li-na; Mettenberg, Donald; Yiu, Cynthia K. Y.; Blizzard, John D.; Wu, Christine D.; Mao, Jing; Drisko, Connie L.; Pashley, David H.; Tay, Franklin R.

    2012-01-01

    Global increase in patients seeking orthodontic treatment creates a demand for the use of acrylic resins in removable appliances and retainers. Orthodontic removable appliance wearers have a higher risk of oral infections that are caused by the formation of bacterial and fungal biofilms on the appliance surface. Here, we present the synthetic route for an antibacterial and antifungal organically-modified silicate (ORMOSIL) that has multiple methacryloloxy functionalities attached to a siloxane backbone (quaternary ammonium methacryloxy silicate, or QAMS). By dissolving the water-insoluble, rubbery ORMOSIL in methyl methacrylate, QAMS may be copolymerized with polymethyl methacrylate, and covalently incorporated in the pressure-processed acrylic resin. The latter demonstrated a predominantly contact-killing effect on Streptococcus mutans ATCC 36558 and Actinomyces naselundii ATCC 12104 biofilms, while inhibiting adhesion of Candida albicans ATCC 90028 on the acrylic surface. Apart from its favorable antimicrobial activities, QAMS-containing acrylic resins exhibited decreased water wettability and improved toughness, without adversely affecting the flexural strength and modulus, water sorption and solubility, when compared with QAMS-free acrylic resin. The covalently bound, antimicrobial orthodontic acrylic resin with improved toughness represents advancement over other experimental antimicrobial acrylic resin formulations, in its potential to simultaneously prevent oral infections during appliance wear, and improve the fracture resistance of those appliances. PMID:22870322

  2. An ORMOSIL-containing orthodontic acrylic resin with concomitant improvements in antimicrobial and fracture toughness properties.

    Directory of Open Access Journals (Sweden)

    Shi-qiang Gong

    Full Text Available Global increase in patients seeking orthodontic treatment creates a demand for the use of acrylic resins in removable appliances and retainers. Orthodontic removable appliance wearers have a higher risk of oral infections that are caused by the formation of bacterial and fungal biofilms on the appliance surface. Here, we present the synthetic route for an antibacterial and antifungal organically-modified silicate (ORMOSIL that has multiple methacryloloxy functionalities attached to a siloxane backbone (quaternary ammonium methacryloxy silicate, or QAMS. By dissolving the water-insoluble, rubbery ORMOSIL in methyl methacrylate, QAMS may be copolymerized with polymethyl methacrylate, and covalently incorporated in the pressure-processed acrylic resin. The latter demonstrated a predominantly contact-killing effect on Streptococcus mutans ATCC 36558 and Actinomyces naselundii ATCC 12104 biofilms, while inhibiting adhesion of Candida albicans ATCC 90028 on the acrylic surface. Apart from its favorable antimicrobial activities, QAMS-containing acrylic resins exhibited decreased water wettability and improved toughness, without adversely affecting the flexural strength and modulus, water sorption and solubility, when compared with QAMS-free acrylic resin. The covalently bound, antimicrobial orthodontic acrylic resin with improved toughness represents advancement over other experimental antimicrobial acrylic resin formulations, in its potential to simultaneously prevent oral infections during appliance wear, and improve the fracture resistance of those appliances.

  3. The photocatalytic enhancement of acrylic and PET solar water disinfection (SODIS) bottles.

    Science.gov (United States)

    Carey, J M; Perez, T M; Arsiaga, E G; Loetscher, L H; Boyd, J E

    2011-01-01

    The solar water disinfection method (SODIS) was modified by the addition of a photocatalytic layer of titania on the interior surface of polyethylene terephthalate (PET) and acrylic bottles. Titania was solvent deposited on the interior of commercially available PET bottles, as well as bottles that were constructed from acrylic. Uncoated and titania-coated acrylic bottles removed 3,000,000-5,000,000 colony forming units per milliliter of K12 E. coli from 670 mL of contaminated water in 40 min of solar irradiance. After five hours of sunlight exposure, the concentration of 10 ppm methyl orange (a representative organic water contaminant), was reduced by 61% using the titania-coated acrylic bottles. The concentration of 87 ppb microcystin-LR (a representative algal toxin) was reduced by 70% after 7 hours of sunlight exposure in the titania-coated acrylic bottles. Acrylic is an effective alternative to PET for use in the SODIS method due to its greater UV transparency. The addition of titania to PET and acrylic bottles confers the ability to remove chemical contaminants in addition to inactivating microbiological contaminants.

  4. Gel polymer electrolytes based on nanofibrous polyacrylonitrile–acrylate for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dul-Sun [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Woo, Jang Chang [Department of Textile Engineering, Inha University, 100 Inharo, Nam-gu Incheon 402-751 (Korea, Republic of); Youk, Ji Ho, E-mail: youk@inha.ac.kr [Department of Textile Engineering, Inha University, 100 Inharo, Nam-gu Incheon 402-751 (Korea, Republic of); Manuel, James [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Ahn, Jou-Hyeon, E-mail: jhahn@gnu.ac.kr [Department of Chemical and Biological Engineering, Research Institute for Green Energy Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of); Department of Materials Engineering and Convergence Technology, Gyeongsang National University, 900 Gajwa-dong, Jinju 660-701 (Korea, Republic of)

    2014-10-15

    Graphical abstract: - Highlights: • Nanofibrous polyacrylonitrile–acrylate membranes were prepared by electrospinning. • Trimethylolpropane triacrylate was used as a crosslinking agent of fibers. • The GPE based on PAN–acrylate (1/0.5) showed good electrochemical properties. - Abstract: Nanofibrous membranes for gel polymer electrolytes (GPEs) were prepared by electrospinning a mixture of polyacrylonitrile (PAN) and trimethylolpropane triacrylate (TMPTA) at weight ratios of 1/0.5 and 1/1. TMPTA is used to achieve crosslinking of fibers thereby improving mechanical strength. The average fiber diameters increased with increasing TMPTA concentration and the mechanical strength was also improved due to the enhanced crosslinking of fibers. GPEs based on electrospun membranes were prepared by soaking them in a liquid electrolyte of 1 M LiPF{sub 6} in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1, v/v). The electrolyte uptake and ionic conductivity of GPEs based on PAN and PAN–acrylate (weight ratio; 1/1 and 1/0.5) were investigated. Ionic conductivity of GPEs based on PAN–acrylate was the highest for PAN/acrylate (1/0.5) due to the proper swelling of fibers and good affinity with liquid electrolyte. Both GPEs based on PAN and PAN–acrylate membranes show good oxidation stability, >5.0 V vs. Li/Li{sup +}. Cells with GPEs based on PAN–acrylate (1/0.5) showed remarkable cycle performance with high initial discharge capacity and low capacity fading.

  5. Facile Fabrication of Gradient Surface Based on (meth)acrylate Copolymer Films

    Science.gov (United States)

    Zhang, Y.; Yang, H.; Wen, X.-F.; Cheng, J.; Xiong, J.

    2016-08-01

    This paper describes a simple and economic approach for fabrication of surface wettability gradient on poly(butyl acrylate - methyl methacrylate) [P (BA-MMA)] and poly(butyl acrylate - methyl methacrylate - 2-hydroxyethyl methacrylate) [P (BA-MMA-HEMA)] films. The (meth)acrylate copolymer [including P (BA-MMA) and P (BA-MMA-HEMA)] films are hydrolyzed in an aqueous solution of NaOH and the transformation of surface chemical composition is achieved by hydrolysis in NaOH solution. The gradient wetting properties are generated based on different functional groups on the P (BA-MMA) and P (BA-MMA-HEMA) films. The effects of both the surface chemical and surface topography on wetting of the (meth)acrylate copolymer film are discussed. Surface chemical composition along the materials length is determined by XPS, and surface topography properties of the obtained gradient surfaces are analyzed by FESEM and AFM. Water contact angle system (WCAs) results show that the P (BA-MMA-HEMA) films provide a larger slope of the gradient wetting than P (BA-MMA). Moreover, this work demonstrates that the gradient concentration of chemical composition on the poly(meth) acrylate films is owing to the hydrolysis processes of ester group, and the hydrolysis reactions that have negligible influence on the surface morphology of the poly(meth) acrylate films coated on the glass slide. The gradient wettability surfaces may find broad applications in the field of polymer coating due to the compatibility of (meth) acrylate polymer.

  6. Effect of thermal cycling and disinfection on microhardness of acrylic resin denture base.

    Science.gov (United States)

    Goiato, Marcelo Coelho; Dos Santos, Daniela Micheline; Baptista, Gabriella Trunckle; Moreno, Amália; Andreotti, Agda Marobo; Dekon, Stéfan Fiuza de Carvalho

    2013-04-01

    The purpose of this study was to investigate the effect of thermal cycling and disinfection on the microhardness of acrylic resins denture base. Four different brands of acrylic resins were evaluated: Onda Cryl, QC 20, Classico and Lucitone. Each brand of acrylic resin was divided into four groups (n = 7) according to the disinfection method (microwave, Efferdent, 4% chlorhexidine and 1% hypochlorite). Samples were disinfected during 60 days. Before and after disinfection, samples were thermal cycled between 5-55 °C with 30-s dwell times for 1000 cycles. The microhardness was measured using a microhardener, at baseline (B), after first thermal cycling (T1), after disinfection (D) and after second thermal cycling (T2). The microhardness values of all groups reduced over time. QC-20 acrylic resin exhibited the lowest microhardness values. At B and T1 periods, the acrylic resins exhibited statistically greater microhardness values when compared to D and T2 periods. It can be concluded that the microhardness values of the acrylic resins denture base were affected by the thermal cycling and disinfection procedures. However, all microhardness values obtained herein are within acceptable clinical limits for the acrylic resins.

  7. Polyurethane acrylate networks including cellulose nanocrystals: a comparison between UV and EB- curing

    Science.gov (United States)

    Furtak-Wrona, K.; Kozik-Ostrówka, P.; Jadwiszczak, K.; Maigret, J. E.; Aguié-Béghin, V.; Coqueret, X.

    2018-01-01

    A water-based polyurethane (PUR) acrylate water emulsion was selected as a radiation curable matrix for preparing nanocomposites including cellulose nanocrystals (CNC) prepared by controlled hydrolysis of Ramie fibers. Cross-linking polymerization of samples prepared in the form of films or of 1 mm-thick bars was either initiated by exposure to the 395 nm light of a high intensity LED lamp or by treatment with low energy electron beam (EB). The conversion level of acrylate functions in samples submitted to increasing radiation doses was monitored by Fourier Transform Infrared Spectroscopy (FTIR). Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) were used to characterize changes in the glass transition temperature of the PUR-CNC nanocomposites as a function of acrylate conversion and of CNC content. Micromechanical testing indicates the positive effect of 1 wt% CNC on Young's modulus and on the tensile strength at break (σ) of cured nanocomposites. The presence of CNC in the PUR acrylate matrix was shown to double the σ value of the nanocomposite cured to an acrylate conversion level of 85% by treatment with a 25 kGy dose under EB, whereas no increase of σ was observed in UV-cured samples exhibiting the same acrylate conversion level. The occurrence of grafting reactions inducing covalent linkages between the polysaccharide nanofiller and the PUR acrylate matrix during the EB treatment is advanced as an explanation to account for the improvement observed in samples cured under ionizing radiation.

  8. Solubility of dense CO2 in two biocompatible acrylate copolymers

    Directory of Open Access Journals (Sweden)

    A. R. C. Duarte

    2006-06-01

    Full Text Available Biocompatible polymers and copolymers are frequently being used as part of controlled delivery systems. These systems can be prepared using a "clean and environment friendly" technology like supercritical fluids. One great advantage of this process is that compressed carbon dioxide has excellent plasticizing properties and can swell most biocompatible polymeric matrixes, thus promoting drug impregnation processes. Mass sorption of two acrylate biocompatible copolymers contact with supercritical carbon dioxide is reported. Equilibrium solubility of dense carbon dioxide in poly(methylmethacrylate-co-ethylhexylacrylate and poly(methylmethacrylate-co-ethylhexylacrylate-co-ethyleneglycoldimethacrylate was studied by a static method at 10.0 MPa and 313 K. The reticulated copolymer had Fickean behavior and its diffusion coefficient was calculated, under operating conditions.

  9. Laboratory analyses of two explanted hydrophobic acrylic intraocular lenses

    Directory of Open Access Journals (Sweden)

    Yunhai Dai

    2014-01-01

    Full Text Available Two three-piece hydrophobic acrylic intraocular lenses (IOLs were explanted from two patients at 7 and 9 years, respectively, after implantation, because of poor fundus visualisation and/or a clinically significant decrease in visual acuity related to their opacified IOLs. In addition to light microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy, confocal laser scanning microscopy was used for the first time to observe the explanted IOLs. The clinical aspect seemed to correspond to the phenomenon of surface light scattering, while laboratory analyses showed dense glistenings in the central layer of the IOL optic, which had no change next to the surface. Further studies on these phenomena are needed.

  10. Polymerisation by acrylamide and acrylic acid inverse suspension

    Directory of Open Access Journals (Sweden)

    Sergio Alejandro LLoreda Blanco

    2010-04-01

    Full Text Available This work describes polymerisation by inverse suspension of acrylamide monomers and acrylic acid for forming homopolymers or copolymers This type of polymersitaion's advantages are described and reasons given for why it should be studied. The article stresses the importance of these types of monomer for obtaining materials presenting great affinity for water, such as super-absorbents and controlled liberation mechanism. Important aspects are presented such as type of initiation, monomer composition and continuous phase composition; parameters are described offering an important basis for formulating a system leading to successfully obtaining the desired materials' most relevant characteristics such as particle distribution and size polymerisation kinetics, conversion and water absorption capacity respecting the system's modifiable parameters. The foregoing is important since the product can be modified, bestowing propierties on it which are suitable for its use.

  11. Water absorbency of chitosan grafted acrylic acid hydrogels

    Science.gov (United States)

    Astrini, N.; Anah, L.; Haryono, A.

    2017-07-01

    Acrylic acid (AA) monomer was directly grafted onto chitosan (CTS) using potassium persulfate (KPS) as an initiator and methylenebisacrylamide (MBA) as a crosslinking agent under an inert atmosphere. One factor affecting the swelling capacity of the obtained hydrogel, KPS concentration, were studied. The hydrogel products were characterized using Fourier Transform Infrared spectroscopy (FTIR) for chemical structure and scanning electron microscopy (SEM) for morphology. Swelling of the hydrogel samples in distilled water and saline solution ( 9% NaCl ) was examined. Swelling capacity of the CTS-g-PAA hydrogels in distilled water (88.53 g/g) was higher than in NaCl solution (29.94 g/g) The highest swelling capacity value was obtained when the grafted reaction was carried out using 2.5wt% initiator

  12. Dental Acrylics - Potential Agent for a Myriad of Diseases

    Directory of Open Access Journals (Sweden)

    Shivangi Gajwani

    2007-01-01

    Full Text Available An allergic reaction also known as a hypersensitivity reaction is caused by the immune system in response to a foreign substance (or allergen. Allergenic chemicals can be found in many products used in the dental operatory. With repeated exposure, these chemicals can cause allergic reactions in dental professionals, resulting in local as well as systemic manifestations. According to various studies done, it became evident that the prevalence of acrylic allergy most commonly in the form of allergic contact dermatitis is affecting the dental personnel to a much greater degree than is believed. Awareness of this disease complex in the form of any new symptoms and potential exposure is paramount for dental personals.

  13. Eco-friendly Crosslinking Agent for Acid Functional Acrylic Resin

    Directory of Open Access Journals (Sweden)

    Archana Shah

    2009-01-01

    Full Text Available Oil from J. multifida was extracted and it was first converted into N,N-bis(2-hydroxyethyl Jatropha fatty amide (HEJFA. HEJFA has been synthesized by reaction between Jatropha oil and diethanol amine in presence of zinc oxide as a catalyst. The reaction is relatively rapid and proceeded to high yield at 200±5 OC. The resulting HEJFA was used to formulate thermosetting coating compositions. Films were cured at ambient (air drying and elevated (stove drying temperatures using N, N-bis(2-hydroxyethyl Jatropha fatty amide (HEJFA as eco-friendly crosslinking agent for acrylic resin. The coating performance of the various compositions was tested by measurement of scratch hardness, impact strength and chemical resistance. The results show better performance of the HEJFA based compositions compared to butylated melamine formaldehyde (MF based compositions.

  14. Scintillation properties of acrylate based plastic scintillator by photoploymerization method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Hwan [Dept. of Radiological Science, Cheongju University, Cheongju (Korea, Republic of); Lee, Joo Il [Dept. of of Radiology, Daegu Health College, Daegu (Korea, Republic of)

    2016-12-15

    In this study, we prepared and characterized a acrylate based UV-curable plastic scintillator. It was used co-polymers TMPTA, DHPA and Ultima GoldTM LLT organic scintillator. The emission spectrum of the plastic scintillator was located in the range of 380⁓520 nm, peaking at 423 nm. And the scintillator is more than 50% transparent in the range of 400⁓ 800 nm. The emission spectrum is well match to the quantum efficiency of photo-multiplier tube and the fast decay time of the scintillation is 12 ns, approximately. This scintillation material provides the possibility of combining 3D printing technology, and then the applications of the plastic scintillator may be expected in human dosimetry etc.

  15. Crosslinkers of Different Types in Precipitation Polymerization of Acrylic Acid

    Directory of Open Access Journals (Sweden)

    H. Eshaghi

    2013-01-01

    Full Text Available Crosslinked poly(acrylic acids were prepared using two types of crosslinker by precipitation polymerization method in a binary organic solvent. N,N’-methylenebisacrylamide (MBA and polyethylene glycol dimethacrylate (PEGDMA-330 were used as low-molecular weight and long-chain crosslinkers, respectively. The effect of various types of crosslinkers on polymer characteristics (i.e., gel content, equilibrium swelling, glass transition temperature, and rheological properties was investigated. Maximum amount of viscosity was obtained by using long-chain crosslinker. The Flory-Rehner equation and rubber elasticity theory were used to discuss the network structure of polymer. It was observed that, the glass transition temperature (Tg of the synthesized polymer containing PEGDMA-330 is higher than that of polymer containing MBA. Apparent and rotational viscosity were used to determine the optimal crosslinker type. In addition, the consistencycoefficient (m and flow behavior index (n parameter of Ostwald equation were investigated as well.

  16. Temperature dependence of the dielectric constant of acrylic dielectric elastomer

    Energy Technology Data Exchange (ETDEWEB)

    Sheng, Junjie; Chen, Hualing; Li, Bo; Chang, Longfei [Xi' an Jiaotong University, State Key Laboratory for Strength and Vibration of Mechanical Structures, Xi' an (China); Xi' an Jiaotong University, School of Mechanical Engineering, Xi' an (China)

    2013-02-15

    The dielectric constant is an essential electrical parameter to the achievable voltage-induced deformation of the dielectric elastomer. This paper primarily focuses on the temperature dependence of the dielectric constant (within the range of 173 K to 373 K) for the most widely used acrylic dielectric elastomer (VHB 4910). First the dielectric constant was investigated experimentally with the broadband dielectric spectrometer (BDS). Results showed that the dielectric constant first increased with temperature up to a peak value and then dropped to a relative small value. Then by analyzing the fitted curves, the Cole-Cole dispersion equation was found better to characterize the rising process before the peak values than the Debye dispersion equation, while the decrease process afterward can be well described by the simple Debye model. Finally, a mathematical model of dielectric constant of VHB 4910 was obtained from the fitted results which can be used to further probe the electromechanical stability of the dielectric elastomers. (orig.)

  17. Novel polymer coatings based on plasma polymerized 2-methoxyethyl acrylate

    DEFF Research Database (Denmark)

    Wu, Zhenning; Jiang, Juan; Benter, Maike

    2008-01-01

    plasma system[4]. The system named SoftPlasma™ is equipped with unique three-phase pulsed AC voltage. Low energy plasma polymerization has almost no thermal load for sensitive polymer materials[5]. Plasma polymerized coatings are highly cross-linked, pin-hole free and provide hydrophilic or hydrophobic...... synthesized by Atom Transfer Radical Polymerization (ATRP)[3]. This enabled a surface segregation of the more hydrophilic block to the polymer/air interface and enrichment of the surface with PMEA. Here we present another way to modify a surface with this material - plasma polymerization in a low energy...... properties[4-6]. We have exploited these possibilities and prepared plasma polymerized 2-methoxyethyl acrylate (PPMEA) coatings on various polymer substrates. The PPMEA coatings were optimized using various plasma polymerization conditions and characterized by X-ray photoelectron spectroscopy...

  18. Temperature dependence of the dielectric constant of acrylic dielectric elastomer

    Science.gov (United States)

    Sheng, Junjie; Chen, Hualing; Li, Bo; Chang, Longfei

    2013-02-01

    The dielectric constant is an essential electrical parameter to the achievable voltage-induced deformation of the dielectric elastomer. This paper primarily focuses on the temperature dependence of the dielectric constant (within the range of 173 K to 373 K) for the most widely used acrylic dielectric elastomer (VHB 4910). First the dielectric constant was investigated experimentally with the broadband dielectric spectrometer (BDS). Results showed that the dielectric constant first increased with temperature up to a peak value and then dropped to a relative small value. Then by analyzing the fitted curves, the Cole-Cole dispersion equation was found better to characterize the rising process before the peak values than the Debye dispersion equation, while the decrease process afterward can be well described by the simple Debye model. Finally, a mathematical model of dielectric constant of VHB 4910 was obtained from the fitted results which can be used to further probe the electromechanical stability of the dielectric elastomers.

  19. Mechanical modeling of interpenetrating polymer network reinforced acrylic elastomer

    Science.gov (United States)

    Schmidt, Arne; Bergamini, Andrea; Kovacs, Gabor; Mazza, Edoardo

    2010-04-01

    Interpenetrating polymer network reinforced acrylic elastomers (IPN) offer outstanding performance in free-standing contractile dielectric elastomer actuators. This work presents the verification of a recently proposed material model for a VHB 4910 based IPN [1]. The 3D large strain material model was determined from extensive data of multiaxial mechanical experiments and allows to account for the variations in material composition of IPN-membranes. We employed inflation tests to membranes of different material composition to study the materials response in a stress state different from the one that was used to extract the material parameters. By applying the material model to finite element models we successfully validated the material model in a range of material compositions typically used for dielectric elastomer actuator applications. In combination with a characterization of electro-mechanical coupling, this 3D large strain model can be used to model IPN-based dielectric elastomer actuators.

  20. Flexural Strength of Cold and Heat Cure Acrylic Resins Reinforced with Different Materials

    Directory of Open Access Journals (Sweden)

    Bijan Heidari

    2015-10-01

    Full Text Available Objectives: Heat-polymerized acrylic resin has been the most commonly used denture base material for over 60 years. However, the mechanical strength of acrylic resin is not adequate for long-term clinical performance of dentures. Consequently, fracture is a com- mon clinical occurrence, which often occurs in the midline of denture base.This study aimed to evaluate the efficacy of cold cure and heat cure acrylic resins, rein- forced with glass fibers, polyethylene fibers, and metal wire for denture base repair.Materials and Methods: Ninety specimens were prepared and allocated to nine groups. Ten specimens were included in the control group, and 80 were allocated to 8 experi- mental groups. In the experimental groups, the specimens were sectioned into two halves from the middle, and were then divided into two main groups: one group was repaired with heat cure acrylic resin, and the other with cold cure acrylic resin. Each group was di- vided into 4 subgroups: unreinforced, reinforced with glass fibers, polyethylene fibers, and metal wire. All specimens were then subjected to a 3-point bending test, and the flexural strength was calculated.Results: The group repaired with heat cure acrylic resin and reinforced with glass fiber showed the highest flexural strength; however, the group repaired with cold cure acrylic resin and reinforced with polyethylene fibers had the lowest flexural strength. There was no significant difference between the groups repaired with heat cure and cold cure acrylic resins without reinforcement.Conclusion: Repairing denture base with heat cure acrylic resin, reinforced with glass fi- bers increases the flexural strength of denture base.

  1. Optimization of cellulose acrylate and grafted 4-vinylpyridine and 1-vinylimidazole synthesis

    Directory of Open Access Journals (Sweden)

    Bojanić Vaso

    2010-01-01

    Full Text Available Optimization of cellulose acrylate synthesis by reaction with sodium cellulosate and acryloyl chloride was carried out. Optimal conditions for conducting the synthesis reaction of cellulose acrylate were as follows: the molar ratio of cellulose/potassium-t-butoxide/acryloyl chloride was 1:3:10 and the optimal reaction time was 10 h. On the basis of elemental analysis with optimal conditions for conducting the reaction of cellulose acrylate, the percentage of substitution of glucose units in cellulose Y = 80.7%, and the degree of substitution of cellulose acrylate DS = 2.4 was determined. The grafting reaction of acrylate vinyl monomers onto cellulose in acetonitrile with initiator azoisobutyronitrile (AIBN in a nitrogen atmosphere was performed, by mixing for 5 h at acetonitrile boiling temperature. Radical copolymerization of synthesized cellulose acrylate and 4-vinylpyridine, 1-vinylimidazole, 1-vinyl-2-pyrrolidinone and 9-vinylcarbazole, cellulose-poly-4-vinylpyridine (Cell-PVP, cellulose-poly-1- vinylimidazole (Cell-PVIm and cellulose-poly-1-vinyl-2-pyrrolidinone (Cell-P1V2P and cellulose-poly-9-vinylcarbazole (Cell-P9VK were synthesized. Acrylate cellulose and cellulose grafted copolymers were confirmed by IR spectroscopy, based on elementary analysis and the characteristics of grafted copolymers of cellulose were determined. The mass share of grafted copolymers, X, the relationship of derivative parts/cellulose vinyl group, Z, and the degree of grafting copolymers of cellulose (mass% were determined. In reaction of methyl iodide and cellulose-poly-4-vinylpyridine (Cell-PVP the cellulose-1-methyl-poly-4-vinylpyridine iodide (Cell-1-Me-PVPJ was synthesized. Cellulose acrylate and grafted copolymers were obtained with better thermal, electrochemical and ion-emulation properties for bonding of noble metals Au, Pt, Pd from water solutions. The synthesis optimization of cellulose acrylate was applied as a model for the synthesis of grafted

  2. Equilibrium water content and glistenings in acrylic intraocular lenses.

    Science.gov (United States)

    Miyata, Akira; Yaguchi, Shigeo

    2004-08-01

    To investigate the possible relationship between temperature and water absorption in acrylic intraocular lenses (IOLs). Laboratory setting, Miyata Eye Clinic, Hiroshima, Japan. The equilibrium water content (amount of water absorbed per weight of the resin x 100) in 2 hydrophobic acrylic IOLs (AcrySof MA60BM [Alcon] and Sensar AR40 [AMO]) was calculated at 30 degrees C, 40 degrees C, and 50 degrees C. The 2 IOLs were also subjected to 3 changes in temperature: from 37 degrees C to 35 degrees C, 39 degrees C to 35 degrees C, and 41 degrees C to 35 degrees C. They were incubated in physiological saline at the higher temperature for 2 hours and at the lower temperature for 30 days before being examined for glistening formation. The water content was higher in the AR40 IOL than in the MA60BM IOL at all temperatures. A temperature-dependent increase in water content was seen in both IOLs, greater in the MA60BM. With a temperature change from 37 degrees C to 35 degrees C, glistening formation was not observed in either IOL. With a temperature change from 39 degrees C to 35 degrees C, glistenings were observed in the MA60BM IOL, and with a temperature change from 41 degrees C to 35 degrees C, they were observed in both IOLs. The change in the equilibrium water content caused by temperature changes between 30 degrees C and 40 degrees C is an important factor in glistening formation, and thus an IOL featuring less temperature-dependent water absorption is less likely to form glistenings.

  3. Preparation, thermal property and morphology analysis of waterborne polyurethane-acrylate

    Science.gov (United States)

    Zhao, Zhenyu; Jing, Zefeng; Qiu, Fengxian; Dai, Yuting; Xu, Jicheng; Yu, Zongping; Yang, Pengfei

    2017-01-01

    A series of waterborne polyurethane-acrylate (WPUA) dispersions were prepared with isophorone diisocyanate (IPDI), polyether polyol (NJ-210), dimethylol propionic acid (DMPA), hydroxyethyl methyl acrylate (HEMA), different proportions of methyl methacrylate (MMA) and ethyl acrylate (MMA and EA) and initiating agent by the emulsion co-polymerization. The structures, thermal properties and morphology of WPUA films were characterized with FT-IR, DSC, SEM and AFM. Performances of the dispersions and films were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The obtained WPUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.

  4. The rising trend in allergic contact dermatitis to acrylic nail products.

    Science.gov (United States)

    Le, Quynh; Cahill, Jennifer; Palmer-Le, Amanda; Nixon, Rosemary

    2015-08-01

    Shellac is a newly available type of long-wearing nail polish, which is becoming increasingly popular. We describe four cases of allergic contact dermatitis (ACD) to acrylates found in Shellac nail products, involving three beauticians and one consumer who purchased the product over the internet. Increasing use of these new acrylic nail products means that dermatologists need to be aware of the possibility of ACD occurring. Testing with hydroxyethyl methacrylate alone, which is included in the Australian Baseline Series, is adequate for screening for acrylate allergy. © 2015 The Australasian College of Dermatologists.

  5. Continuous Flow Magnesiation or Zincation of Acrylonitriles, Acrylates, and Nitroolefins. Application to the Synthesis of Butenolides.

    Science.gov (United States)

    Ganiek, Maximilian A; Becker, Matthias R; Ketels, Marthe; Knochel, Paul

    2016-02-19

    Scalable continuous flow procedures are reported for the metalation and downstream functionalization of β-substituted acrylates. The flow conditions allow the metalation of acrylonitriles, acrylates, and nitroolefins at 0.25-2.50 mmol/min conversion rates. Magnesiations can be performed with short residence times (1-20 min) and near-ambient temperature using TMPMgCl·LiCl. Further, high temperature zincation (≤90 °C) using TMPZnCl·LiCl is possible. This method allows a simple entry to 2(5H)-furanones by flow generation of magnesiated acrylates and a subsequent reaction with aldehydes.

  6. Studies on the Influence of Monomers on the Performance Properties of Epoxy Acrylate Resin

    Directory of Open Access Journals (Sweden)

    Amrita Sharma

    2008-01-01

    Full Text Available Twelve blend samples were prepared by physical mixing of epoxy acrylate resins with various monomers viz. ethoxylated phenol monoacrylate (EOPA, tripropylene glycol diacrylate (TPGDA and trimethylol propane tri acrylate(TMPTA, having weight ratio of epoxy acrylate resin and monomers are 50:50, 60:40, 70:30, 80:20. These samples were cured under UV radiation using 5% photo initiator by weight. These blends were evaluated for mechanical, chemical & thermal properties. It was found that the sample having mono & tri functional monomers shows better properties than the samples having di functional monomer.

  7. Perceived gender in clear and conversational speech

    Science.gov (United States)

    Booz, Jaime A.

    Although many studies have examined acoustic and sociolinguistic differences between male and female speech, the relationship between talker speaking style and perceived gender has not yet been explored. The present study attempts to determine whether clear speech, a style adopted by talkers who perceive some barrier to effective communication, shifts perceptions of femininity for male and female talkers. Much of our understanding of gender perception in voice and speech is based on sustained vowels or single words, eliminating temporal, prosodic, and articulatory cues available in more naturalistic, connected speech. Thus, clear and conversational sentence stimuli, selected from the 41 talkers of the Ferguson Clear Speech Database (Ferguson, 2004) were presented to 17 normal-hearing listeners, aged 18 to 30. They rated the talkers' gender using a visual analog scale with "masculine" and "feminine" endpoints. This response method was chosen to account for within-category shifts of gender perception by allowing nonbinary responses. Mixed-effects regression analysis of listener responses revealed a small but significant effect of speaking style, and this effect was larger for male talkers than female talkers. Because of the high degree of talker variability observed for talker gender, acoustic analyses of these sentences were undertaken to determine the relationship between acoustic changes in clear and conversational speech and perceived femininity. Results of these analyses showed that mean fundamental frequency (fo) and f o standard deviation were significantly correlated to perceived gender for both male and female talkers, and vowel space was significantly correlated only for male talkers. Speaking rate and breathiness measures (CPPS) were not significantly related for either group. Outcomes of this study indicate that adopting a clear speaking style is correlated with increases in perceived femininity. Although the increase was small, some changes associated

  8. Cellulose Degradation by Cellulose-Clearing and Non-Cellulose-Clearing Brown-Rot Fungi

    OpenAIRE

    Highley, Terry L.

    1980-01-01

    Cellulose degradation by four cellulose-clearing brown-rot fungi in the Coniophoraceae—Coniophora prasinoides, C. puteana, Leucogyrophana arizonica, and L. olivascens—is compared with that of a non-cellulose-clearing brown-rot fungus, Poria placenta. The cellulose- and the non-cellulose-clearing brown-rot fungi apparently employ similar mechanisms to depolymerize cellulose; most likely a nonenzymatic mechanism is involved.

  9. SPECIAL MINING MANAGEMENT ZONE - CLEAR CREEK, IDAHO.

    Science.gov (United States)

    Lund, Karen; Esparza, Leon E.

    1984-01-01

    On the basis of mineral-resource surveys, a substantiated resource potential for sediment-hosted cobalt-copper-gold-silver deposits has been identified in the Elkhorn and upper Garden Creek areas of the Special Mining Management Zone - Clear Creek, Idaho. Areas of favorable host rock, but with less strong evidence of mineralization, were classified as having probable resource potential for the same kind of deposit. A probable resource potential for porphyry-type copper-molybdenum deposits is assigned to areas along Clear Creek and upper Squaw Gulch based on the presence of extensive stockwork fracturing and alteration of the nonporphyritic granite, introduced disseminated magnetite, and the close proximity of known Tertiary plutons. The nature of the geologic terrain makes the occurrence of organic fuels on geothermal resources extremely unlikely.

  10. CLEARING MAGNET DESIGN FOR APS-U

    Energy Technology Data Exchange (ETDEWEB)

    Abliz, M.; Grimmer, J.; Jaski, Y.; Westferro, F.; Ramanathan, M.

    2017-06-25

    The Advanced Photon Source is in the process of developing an upgrade (APS-U) of the storage ring. The upgrade will be converting the current double bend achromat (DBA) lattice to a multi-bend achromat (MBA) lattice. In addition, the storage ring will be operated at 6 GeV and 200 mA with regular swap-out injection to keep the stored beam current constant [1]. The swap-out injection will take place with beamline shutters open. For radiation safety to ensure that no electrons can exit the storage ring, a passive method of protecting the beamline and containing the electrons inside the storage ring is proposed. A clearing magnet will be located in all beamline front ends inside the storage ring tunnel. This article will discuss the features and design of the clearing magnet scheme for APS-U.

  11. Roadmap-Based Level Clearing of Buildings

    KAUST Repository

    Rodriguez, Samuel

    2011-01-01

    In this paper we describe a roadmap-based approach for a multi-agent search strategy to clear a building or multi-story environment. This approach utilizes an encoding of the environment in the form of a graph (roadmap) that is used to encode feasible paths through the environment. The roadmap is partitioned into regions, e.g., one per level, and we design region-based search strategies to cover and clear the environment. We can provide certain guarantees within this roadmap-based framework on coverage and the number of agents needed. Our approach can handle complex and realistic environments where many approaches are restricted to simple 2D environments. © 2011 Springer-Verlag.

  12. Clearing and settlement in a legal perspective

    OpenAIRE

    Andersen, Niels C.

    2004-01-01

    This paper describes how the two most important clearing and settlement systems in Denmark, VP and the Sumclearing, work in practice. Further it analyses, how the legal framework in the Securities Trading Act, STA, based on directive 98/26/EC on settlement finality in payment and securities settlement systems works in relation to the functionality of VP and the Sumclearing. The functionality for both systems encompasses net settlement (multilateral netting). The description of the two systems...

  13. Clearing og afvikling i et retligt perspektiv

    OpenAIRE

    Andersen, Niels C.

    2004-01-01

    This paper describes how the two most important clearing and settlement systems in Denmark, VP and the Sumclearing, work in practice. Further it analyses, how the legal framework in the Securities Trading Act, STA, based on directive 98/26/EC on settlement finality in payment and securities settlement systems works in relation to the functionality of VP and the Sumclearing. The functionality for both systems encompasses net settlement (multilateral netting). The description of the two systems...

  14. Internet compromise clears way for WSIS agreement

    CERN Multimedia

    Ermert, M

    2003-01-01

    A working group under the leadership of United Nations Secretary General Kofi Annan himself will try to resolve the deep differences on the question of Internet governance, officials said here. The group, whose exact membership wasn't immediately clear, is to propose a solution to the controversial issue that has given negotiators at the World Summit of the Information Society (WSIS) a headache (1/2 page).

  15. Imaging of ovarian clear cell carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, Toshihiko; Sawano, Seishi; Yamada, Keiko [Japanese Foundation for Cancer Research, Tokyo (Japan). Hospital] (and others)

    1999-12-01

    The aim of this study is to examine the appearance of ovarian clear cell adenocarcinoma (OCCA) on MR, CT, US. In 39 cases with OCCA, the imaging characteristics of OCCA were evaluated morphologically and classified into three groups, that was, monomural nodule type, multi-mural nodule type and predominantly solid type. Forty-three percent of the patients had endometriosis. Contrast material-enhanced MRI was the most useful method for diagnosis of OCCA. (author)

  16. Biocompatibility of poly(ethylene glycol) and poly(acrylic acid) interpenetrating network hydrogel by intrastromal implantation in rabbit cornea.

    Science.gov (United States)

    Zheng, Luo Luo; Vanchinathan, Vijay; Dalal, Roopa; Noolandi, Jaan; Waters, Dale J; Hartmann, Laura; Cochran, Jennifer R; Frank, Curtis W; Yu, Charles Q; Ta, Christopher N

    2015-10-01

    We evaluated the biocompatibility of a poly(ethylene glycol) and poly(acrylic acid) (PEG/PAA) interpenetrating network hydrogel designed for artificial cornea in a rabbit model. PEG/PAA hydrogel measuring 6 mm in diameter was implanted in the corneal stroma of twelve rabbits. Stromal flaps were created with a microkeratome. Randomly, six rabbits were assigned to bear the implant for 2 months, two rabbits for 6 months, two rabbits for 9 months, one rabbit for 12 months, and one rabbit for 16 months. Rabbits were evaluated monthly. After the assigned period, eyes were enucleated, and corneas were processed for histology and immunohistochemistry. There were clear corneas in three of six rabbits that had implantation of hydrogel for 2 months. In the six rabbits with implant for 6 months or longer, the corneas remained clear in four. There was a high rate of epithelial defect and corneal thinning in these six rabbits. One planned 9-month rabbit developed extrusion of implant at 4 months. The cornea remained clear in the 16-month rabbit but histology revealed epithelial in-growth. Intrastromal implantation of PEG/PAA resulted in a high rate of long-term complications. © 2015 Wiley Periodicals, Inc.

  17. Carbon fiber reinforced thermoplastic composites from acrylic polymer matrices: Interfacial adhesion and physical properties

    Directory of Open Access Journals (Sweden)

    H. Kishi

    2017-04-01

    Full Text Available Acrylic polymers have high potential as matrix polymers for carbon fiber reinforced thermoplastic polymers (CFRTP due to their superior mechanical properties and the fact that they can be fabricated at relatively low temperatures. We focused on improving the interfacial adhesion between carbon fibers (CFs and acrylic polymers using several functional monomers for co-polymerization with methyl methacrylate (MMA. The copolymerized acrylic matrices showed good adhesion to the CF surfaces. In particular, an acrylic copolymer with acrylamide (AAm showed high interfacial adhesive strength with CFs compared to pure PMMA, and a hydroxyethyl acrylamide (HEAA copolymer containing both amide and hydroxyl groups showed high flexural strength of the CFRTP. A 3 mol% HEAA-copolymerized CFRTP achieved a flexural strength almost twice that of pure PMMA matrix CFRTP, and equivalent to that of an epoxy matrix CFRP.

  18. Allergic contact dermatitis from ultraviolet cured inks. Allergic contact sensitization to acrylates.

    Science.gov (United States)

    Emmett, E A; Kominsky, J R

    1977-02-01

    Eight men employed in the manufacture of ultraviolet cured inks developed allergic contact dermatitis predominantly on the exposed areas. Patch testing revealed sensitization to trimethylol propane triacrylate in seven employees, to 1,6-hexanediol diacrylate in six employees, to pentaerythritol triacrylatylate in four employees and to epoxy acrylate oligomers in three employees. Either cross-sensitization or concomitant sensitization may have accounted for the multiple reactions in several employees. One sensitized employee was patch tested with four different commercially available epoxy acrylate oligomers and reacted only to two, suggesting that variations possibly in chain length between these oligomers are important variables in the allergic reactions. The polyfunctional acrylic monomers and certain epoxy acrylate oligomers should be handled carefully to avoid the development of allergic contact dermatitis.

  19. Correlation between stated and measured concentrations of acrylate and methacrylate allergens in patch-test preparations.

    Science.gov (United States)

    Goon, Anthony Teik-Jin; Bruze, Magnus; Zimerson, Erik; Sörensen, Osten; Goh, Chee-Leok; Koh, David Soo-Quee; Isaksson, Marléne

    2011-01-01

    Contact allergy to acrylates and methacrylates is not uncommon. The allergy is confirmed by patch-testing patients with commercial patch-test preparations. To investigate acrylate and methacrylate allergens used for patch testing in nine different dermatology departments from Europe, America, Asia, and Australia. The acrylate and methacrylate (methyl methacrylate, 2-hydroxypropyl acrylate, 2-hydroxyethyl methacrylate, ethylene glycol dimethacrylate, and triethylene glycol diacrylate) allergen samples were analyzed with high-performance liquid chromatography to measure the allergen content. Variation in measured versus stated concentrations was seen in these samples. The ratio of measured to stated concentrations ranged from 0.11 to 1.1. Only 22 (63%) of 35 samples were within the arbitrary acceptable limits of 80 to 120% of the stated concentrations. The results may have implications for individual diagnosis and prevention and when test results from various centers are compared.

  20. Acrylate-induced allergic contact dermatitis in a car windscreen repairer

    National Research Council Canada - National Science Library

    Fremlin, G; Sansom, J

    2014-01-01

    .... He was patch tested to the British Society for Cutaneous Allergy standard and preservatives series and to the two acrylates used in his work environment, identified using safety data sheets, methyl methacrylate 2...

  1. Color Stability of Heat‑cure Acrylic Resin Subjected to Simulated ...

    African Journals Online (AJOL)

    heat‑cure acrylic resin (Ivoclar Triplex Hot‑V) specimens are randomly allocated into four ..... subsequently release oxygen and loosens debris by mechanical means. ... of external colorants, i.e., food substances and colorants used in denture ...

  2. Cell Adhesion to Acrylic Custom Provisional Abutment Placed on an Immediate Implant: A Case Report.

    Science.gov (United States)

    Saito, Hanae; Hsia, Ru-Ching; Tarnow, Dennis P; Reynolds, Mark A

    2017-02-01

    This article presents the results of a scanning electron microscope (SEM) analysis of the surface of an acrylic custom provisional abutment following first disconnection from a post-extraction immediate implant placement. An implant was placed immediately after extraction, the site was grafted, and a barrier membrane was adapted for graft containment. A custom acrylic shell was then relined, polished, and steam-cleaned prior to being screwed onto the implant. After 5 months of undisturbed healing, the custom provisional abutment was disconnected for the first time and processed for SEM examination. The surface of the custom acrylic abutment revealed well-spread fibroblast-like cells with filopodia inserting into the porous surface. These observations suggest that the surface topography of the acrylic provisional restoration/ abutment can function as a substratum for cellular adhesion and may serve an important role in supporting peri-implant mucosa at the time of immediate implant placement.

  3. Novel lighter weight crystalline silicon photovoltaic module using acrylic-film as a cover sheet

    Science.gov (United States)

    Kajisa, Taira; Miyauchi, Haruko; Mizuhara, Kazumi; Hayashi, Kentaro; Tokimitsu, Tooru; Inoue, Masanao; Hara, Kohjiro; Masuda, Atsushi

    2014-09-01

    Lighter weight multicrystalline silicon photovoltaic (PV) modules were investigated by substitution of acrylic thin film for standard glass as a cover sheet. Acrylic-film PV mini modules were fabricated with the composition determined from stress simulation results and tested for long-term reliability against thermal changes and humidity. The results revealed that the acrylic-film-cover-sheet PV module satisfied the qualifying standards of all the reliability tests in both the module appearance after tests and the electrical properties. Moreover, the PV module proved to be durable in the impact resistance test, even though the cover sheet was thinner. In addition, the electrical properties of the PV module were unaffected in the potential-induced degradation (PID) test, whereas those of the standard glass module were significantly deteriorated. These results indicated that it is possible for the lighter weight acrylic-film PV module to be used in the immediate future.

  4. Toward pH-responsive coating materials--high-throughput study of (meth)acrylic copolymers.

    Science.gov (United States)

    Krieg, Andreas; Arici, Elif; Windhab, Norbert; Schattka, Jan Hendrik; Schubert, Stephanie; Schubert, Ulrich S

    2014-08-11

    The release behavior of a model compound (β-naphthol orange) encapsulated in (meth)acrylate-based statistical copolymers under different environmental conditions was investigated. From monomers of varying polarity (methyl acrylate, ethyl acrylate, tert-butyl acrylate, 2-ethylhexyl methacrylate, and benzyl methacrylate) in combination with methacrylic acid, five polymer series were synthesized by free radical polymerization. The pH-dependent release kinetics were investigated via UV-vis spectroscopy at pH 1.2 and 6.8, simulating physiological conditions in the stomach and intestines. Furthermore, the influence of different ethanol contents (0 and 40 vol %) in the acidic medium was investigated. The whole approach was designed to meet the requirements of a high-throughput experimentation workflow.

  5. Biobased composites from thermoplastic polyurethane elastomer and cross-linked acrylated-epoxidized soybean oil

    Science.gov (United States)

    Soybean oil is an important sustainable material. Crosslinked acrylated epoxidized soybean oil (AESO) is brittle without flexibility and the incorporation of thermoplastic polyurethane improves its toughness for industrial applications. The hydrophilic functional groups from both oil and polyurethan...

  6. The Synthesis and Characterization of Poly(methyl methacrylate-tourmaline acrylate)

    National Research Council Canada - National Science Library

    Hu, Yingmo; Chen, Xubo; Li, Yunhua

    2016-01-01

    ... and then copolymerization with methyl methacrylate to get poly(methyl methacrylate-tourmaline acrylate). The synthetic processes were optimized, and the structures of the as-prepared samples were characterized by IR, SEM, and X-ray fluorescence analysis...

  7. The acrylic's design or the addition of internal orthodontic wire changes the resistance of orthodontic plates?

    OpenAIRE

    PITHON, Matheus Melo; Sousa,Érica Luiza Santana Moreira; Fogaça,Davi Novaes Ladeia; Silva,William Soares da; Rodrigues, Luciano Brito; Coqueiro, Raildo Silva

    2013-01-01

    OBJECTIVE: Evaluate resistance of Hawley retainers in three different acrylic configurations in order to evaluate if its format or the addition of internal wire interferes in its resistance. MATERIAL AND METHOD: 45 Hawley retainers were fabricated, divided into three groups (n = 15): Group 1 - acrylic covering the entire hard palate, Group 2 - plate with relief at the deepest region of the palate, leaving it with a "U" conformation and Group 3 - similar to Group 2, with the addition of 0.7mm ...

  8. Swelling of Superabsorbent Acrylamide/Sodium Acrylate Hydrogels Prepared Using Multifunctional Crosslinkers

    OpenAIRE

    KARADAĞ, Erdener

    2014-01-01

    Superwaterabsorbent acrylamide-sodium acrylate hydrogels were Prepared by free radical polymerization in aqueous solutions of acrylamide and of acrylamide with sodium acrylate as comonomer. For each copolymerization, nine different compositions were used and in all systems a concentration of a multifunctional crosslinker such as trimethylolpropane triacrylate, ethylene glycol dimethacrylate, 1,4-butanediol dimethacrylate and N,N'-methylenebisacrylamide was employed. As a re...

  9. Comparison of acrylic and polymethyl methacrylate lenses in a pediatric population

    OpenAIRE

    Aasuri Murali; Fernandes Merle; Pathan Padmaja

    2006-01-01

    Purpose: To compare the intra-patient incidence of posterior capsular opacification (PCO) and their post operative course, in children with bilateral cataract, following implantation of acrylic (Group 1) and polymethyl methacrylate (PMMA) (Group 2) intraocular lenses (IOLs). Materials and Methods: This was a prospective, interventional intra-patient case series. Twenty-five children with bilateral cataract, 5 years and older, underwent cataract surgery and implantation of an acrylic (AcryS...

  10. Characterization and bacterial anti-adherent effect on modified PMMA denture acrylic resin containing platinum nanoparticles

    OpenAIRE

    Nam, Ki-Young

    2014-01-01

    PURPOSE This study characterized the synthesis of a modified PMMA (Polymethyl methacrylate) denture acrylic loading platinum nanoparticles (PtN) and assessed its bacterial inhibitory efficacy to produce novel antimicrobial denture base material. MATERIALS AND METHODS Polymerized PMMA denture acrylic disc (20 mm × 2 mm) specimens containing 0 (control), 10, 50, 100 and 200 mg/L of PtN were fabricated respectively. The obtained platinum-PMMA nanocomposite (PtNC) was characterized by TEM (transm...

  11. Testing of gloves for permeability to UV-curable acrylate coatings

    Energy Technology Data Exchange (ETDEWEB)

    Huggins, R.; Levy, N.; Pruitt, P.M.

    1987-07-01

    The handling of UV-curable acrylate formulations used in the coating of optical fiber requires protective measures to prevent contact dermatitis and/or allergic dermatitis. To characterize the permeability of various glove materials to a UV-curable acrylate coating, a study was undertaken using a modification of a standard ASTM permeability test, which demonstrated that nitrile rubber gloves provided the best protection of those glove materials tested.

  12. Testing of gloves for permeability to UV-curable acrylate coatings.

    Science.gov (United States)

    Huggins, R; Levy, N; Pruitt, P M

    1987-07-01

    The handling of UV-curable acrylate formulations used in the coating of optical fiber requires protective measures to prevent contact dermatitis and/or allergic dermatitis. To characterize the permeability of various glove materials to a UV-curable acrylate coating, a study was undertaken using a modification of a standard ASTM permeability test, which demonstrated that nitrile rubber gloves provided the best protection of those glove materials tested.

  13. Allergic contact dermatitis due to urethane acrylate in ultraviolet cured inks.

    OpenAIRE

    Nethercott, J R; Jakubovic, H R; Pilger, C.; Smith, J. W.

    1983-01-01

    Seven workers exposed to ultraviolet printing inks developed contact dermatitis. Six cases were allergic and one irritant. A urethane acrylate resin accounted for five cases of sensitisation, one of which was also sensitive to pentaerythritol triacrylate and another also to an epoxy acrylate resin. One instance of allergy to trimethylpropane triacrylate accounted for the sixth case of contact dermatitis in this group of workers. An irritant reaction is presumed to account for the dermatitis i...

  14. Acrylic acid derivatives of group 8 metal carbonyls: a structural and kinetic study.

    Science.gov (United States)

    Li, Bo; Kyran, Samuel J; Yeung, Andrew D; Bengali, Ashfaq A; Darensbourg, Donald J

    2013-05-06

    The synthesis, spectroscopic, and X-ray structural studies of acrylic acid complexes of iron and ruthenium tetracarbonyls are reported. In addition, the deprotonated η(2)-olefin bound acrylic acid derivative of iron as well as its alkylated species were fully characterized by X-ray crystallography. Kinetic data were determined for the replacement of acrylic acid, acrylate, and methylacrylate for the group 8 metal carbonyls by triphenylphosphine. These processes were found to be first-order in the concentration of metal complex with the rates for dissociative loss of the olefinic ligands from ruthenium being much faster than their iron analogues. However, the ruthenium derivatives afforded formation of primarily mono-phosphine metal tetracarbonyls, whereas the iron complexes led largely to trans-di-phosphine tricarbonyls. This difference in behavior was ascribed to a more stable spin crossover species (3)Fe(CO)4 which undergoes rapid CO loss to afford the bis phosphine derivative. The activation enthalpies for dissociative loss of the deprotonated η(2)-bound acrylic acid ligand were found to be larger than their corresponding values in the protonated derivatives. For example, for dissociative loss of the protonated and deprotonated acrylic acid derivatives of iron(0) the ΔH(‡) values determined were 28.0 ± 1.2 and 34.1 ± 1.5 kcal·mol(-1), respectively. Density functional theory (DFT) computations of the bond dissociation energies (BDEs) in these acrylic acids and closely related complexes were in good agreement with enthalpies of activation for these ligand substitution reactions, supportive of a dissociative mechanism for olefin displacement. Processes related to catalytic production of acrylic acid from CO2 and ethylene are considered.

  15. Silane-Acrylate Chemistry for Regulating Network Formation in Radical Photopolymerization.

    Science.gov (United States)

    Steindl, Johannes; Koch, Thomas; Moszner, Norbert; Gorsche, Christian

    2017-10-10

    Photoinitiated silane-ene chemistry has the potential to pave the way toward spatially resolved organosilicon compounds, which might find application in biomedicine, microelectronics, and other advanced fields. Moreover, this approach could serve as a viable alternative to the popular photoinitiated thiol-ene chemistry, which gives access to defined and functional photopolymer networks. A difunctional bis(trimethylsilyl)silane with abstractable hydrogens (DSiH) was successfully synthesized in a simple one-pot procedure. The radical reactivity of DSiH with various homopolymerizable monomers (i.e., (meth)acrylate, vinyl ester, acrylamide) was assessed via (1)H NMR spectroscopic studies. DSiH shows good reactivity with acrylates and vinyl esters. The most promising silane-acrylate system was further investigated in cross-linking formulations toward its reactivity (e.g., heat of polymerization, curing time, occurrence of gelation, double-bond conversion) and compared to state-of-the-art thiol-acrylate resins. The storage stability of prepared resin formulations is greatly improved for silane-acrylate systems vs thiol-ene resins. Double-bond conversion at the gel point (DBCgel) and overall DBC were increased, and polymerization-induced shrinkage stress has been significantly reduced with the introduction of silane-acrylate chemistry. Resulting photopolymer networks exhibit a homogeneous network architecture (indicated by a narrow glass transition) that can be tuned by varying silane concentration, and this confirms the postulated regulation of radical network formation. Similar to thiol-acrylate networks, this leads to more flexible photopolymer networks with increased elongation at break and improved impact resistance. Additionally, swelling tests indicate a high gel fraction for silane-acrylate photopolymers.

  16. Preparation of a Novel Water-based Acrylic Multi-Thermal Insulation Coating

    OpenAIRE

    Xiufang YE; Dongchu CHEN; Chang, Menglei; Youtian MO; Wang, Qingxiang

    2017-01-01

    To efficiently improve the thermal insulation effect of coatings, a novel water-based acrylic multi-thermal insulation coating (multi-WATIC) combined with thermal obstruction, echo, and radiation was prepared. The category and ratio of thermal insulation functional fillers are crucial. First, water-based acrylic thermal insulation coating (WATIC) with single thermal insulation functional fillers was prepared, and the thermal insulation property tests were done. Thereafter, a novel multi-WATIC...

  17. Evaluation of surface physical properties of acrylic resins for provisional prosthesis

    OpenAIRE

    Sérgio Paulo Hilgenberg; Emigdio Enrique Orellana-Jimenez; Wilmer Fabian Sepúlveda-Navarro; Beatriz Elena Arana-Correa; Dario César Teixeira Alves; Nara Hellen Campanha

    2008-01-01

    Acrylic resins used for provisional prostheses should have satisfactory superficial characteristics in order to ensure gingival health and low bacterial attachment. The purpose of the present study was to evaluate the superficial roughness and contact angle after two types of polishing and the Vickers hardness of three acrylic resins (Duralay - G1, Dencrilay - G2, and Dencor - G3), all shade 66, indicated for provisional fixed prostheses. Five 20 x 3 ± 1 mm diameter discoid specimens were obt...

  18. Kinetics and mechanism of polymer dispersion formation on based of (meth)acrylates. Part 2

    OpenAIRE

    GOLDFEIN M.D.; KOZHEVNIKOV N.V.; KOZHEVNIKOVA N.I.; ZAIKOV G.E.

    2015-01-01

    The aim of the present work was to establish the kinetics and mechanism of joint emulsion polymerization of methyl acrylate with metacrylic acid (MAA) or acrylonitrile, which underlies production of many commercial acrylic polymeric dispersions. The emulsion polymerization of methyl methacrylate (MMA) and copolymers with acrylonitrile (AN) and methacrylic acid (MAA) was studied. Also some aspects of kinetics and mechanism of polymeric latexes formation processes in absence of emulsifier were ...

  19. Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins

    OpenAIRE

    Paulo Maurício Batista da Silva; Emílio José Tabaré Rodríguez Acosta; Matheus Jacobina; Luciana de Rezende Pinto; Vinícius Carvalho Porto

    2011-01-01

    OBJECTIVE: Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. MATERIAL AND METHODS: Sixty disc-shaped specimens (40 mm x 3 mm) were fabricated from two different brands (Artiplus and Trilux) of denture ...

  20. IN VITRO ANTIFUNGAL ACTION OF DIFFERENT SUBSTANCES OVER MICROWAVED-CURED ACRYLIC RESINS

    OpenAIRE

    Montagner, Henrique; Montagner, Francisco; Braun, Katia Olmedo; Peres, Paulo Edelvar Correa; Gomes, Brenda Paula Figueiredo de Almeida

    2009-01-01

    OBJECTIVE: The presence of Candida albicans on the surfaces of denture-base acrylic resins is strongly related to the development of oral stomatitis. This study evaluated the antifungal action of different agents over microwave-cured acrylic resin without polishing specimens previously contaminated with Candida albicans. MATERIAL AND METHODS: Sixty specimens were immersed in BHI broth previously inoculated with the yeast and stored for 3 h at 37ºC. They were divided into 5 experimental groups...

  1. ClearedLeavesDB: an online database of cleared plant leaf images.

    Science.gov (United States)

    Das, Abhiram; Bucksch, Alexander; Price, Charles A; Weitz, Joshua S

    2014-03-28

    Leaf vein networks are critical to both the structure and function of leaves. A growing body of recent work has linked leaf vein network structure to the physiology, ecology and evolution of land plants. In the process, multiple institutions and individual researchers have assembled collections of cleared leaf specimens in which vascular bundles (veins) are rendered visible. In an effort to facilitate analysis and digitally preserve these specimens, high-resolution images are usually created, either of entire leaves or of magnified leaf subsections. In a few cases, collections of digital images of cleared leaves are available for use online. However, these collections do not share a common platform nor is there a means to digitally archive cleared leaf images held by individual researchers (in addition to those held by institutions). Hence, there is a growing need for a digital archive that enables online viewing, sharing and disseminating of cleared leaf image collections held by both institutions and individual researchers. The Cleared Leaf Image Database (ClearedLeavesDB), is an online web-based resource for a community of researchers to contribute, access and share cleared leaf images. ClearedLeavesDB leverages resources of large-scale, curated collections while enabling the aggregation of small-scale collections within the same online platform. ClearedLeavesDB is built on Drupal, an open source content management platform. It allows plant biologists to store leaf images online with corresponding meta-data, share image collections with a user community and discuss images and collections via a common forum. We provide tools to upload processed images and results to the database via a web services client application that can be downloaded from the database. We developed ClearedLeavesDB, a database focusing on cleared leaf images that combines interactions between users and data via an intuitive web interface. The web interface allows storage of large collections

  2. The role of acrylic acid impurity as a sensitizing component in electrocardiogram electrodes.

    Science.gov (United States)

    Stingeni, Luca; Cerulli, Emilia; Spalletti, Anna; Mazzoli, Alessandra; Rigano, Luigi; Bianchi, Leonardo; Hansel, Katharina

    2015-07-01

    Allergic contact dermatitis caused by (meth)acrylates is well known, both in occupational and in non-occupational settings. Contact hypersensitivity to electrocardiogram (ECG) electrodes containing (meth)acrylates is rarely reported. To report the first case of contact dermatitis caused by acrylic acid impurity in ECG electrodes. Patch tests were performed with separate components of electrodes and some (meth)acrylates. This was followed by high-performance liquid chromatography of electrode hydrogel. The patient was contact-allergic to electrode hydrogel but not to its separate constituents. Positive reactions were observed to 2-hydroxyethyl methacrylate (2-HEMA), 2-hydroxypropyl methacrylate (2-HPMA) and ethyleneglycol dimethacrylate (EGDMA). Subsequent analysis showed that the electrode hydrogel contained acrylic acid as an impurity. The latter was subsequently patch tested, with a positive result. The sensitization resulting from direct contact with ECG electrodes was caused by acrylic acid, present as an impurity in ECG electrodes. Positive reactions to 2-HEMA, 2-HPMA and EGDMA are considered to be cross-reactions. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  3. Allergic contact dermatitis from sculptured acrylic nails: special presentation with an airborne pattern

    Science.gov (United States)

    Maio, Paula; Carvalho, Rodrigo; Amaro, Cristina; Santos, Raquel; Cardoso, Jorge

    2012-01-01

    Methylmethacrylate was first reported in 1941 as a cause of contact dermatitis. Since then, occupational contact allergies to acrylates in dentistry, orthopedic surgery, printing industry and industry have been reported, but few reports are found in the literature as a consequence of the contact with sculptured artificial acrylic nails which are increasingly popular. We describe here 3 patients with contact allergy to acrylates in artificial sculptured nails. Patch tests were performed with the Portuguese baseline series of contact allergens and an extended series of acrylates were applied. In particular, we tested three female patients with allergic contact dermatitis from sculptured acrylic nails. Two of these patients were both customers and also technical nail beauticians. Two patients developed periungual eczema; one presented only with face and eyelid dermatitis had no other lesions. The tests showed positive reaction to 2-hydroxyethylmethacrylate (2-HEMA) and 2-hydroxypropylmethacrylate (2-HPMA) in all the three patients. Our cases demonstrate the variety of clinical presentations of allergic contact dermatitis from acrylic sculptured nails. They show the need to warn patients of persistent and sometimes permanent side effects of these products. They also emphasize the importance of cosmetic ingredient labeling. PMID:25386316

  4. MM and QM: conformational and vibrational spectra analysis of 2-hydroxyethyl acrylate.

    Science.gov (United States)

    Belaidi, O; Adjim, M; Bouchaour, T; Maschke, U

    2015-02-25

    2-Hydroxyethyl acrylate is generally used with other acrylic and methacrylic products in order to get the desired characteristics of the final product. In this work we are about to make an assignment of experimental infrared bands with the help of a theoretical quantum chemistry calculations. The exact knowledge of some bands which are not characteristics of acrylic materials will enable us to make a quick analysis with available techniques of low costs for mixtures of polymers based on acrylate and methacrylate molecules. In the experimental part, the infrared spectrum of 2-hydroxyethyl acrylate is obtained by using a FTIR Perkin Elmer model 2000. In the computational part and as first step, the theoretical calculations are performed by the semi-empirical AM1 method for excluding similar structures of 2-hydroxyethyl acrylate molecule by a meticulous conformational analysis. As a second step the obtained structures are optimized using DFT. The simulated frequencies are then scaled and a tentative assignment is made based on band intensities and PED percentages. The theoretical calculations predict the existence of thirteen conformations two of them represent the majority of experimental bands in the infrared spectrum. Two neighbor experimental bands located at 1301 and 1207 cm(-1) maybe used as characteristic bands to locate and distinguish the existence of one or both conformations. Copyright © 2014 Elsevier B.V. All rights reserved.

  5. Mechanistic insight into acrylate metabolism and detoxification in marine dimethylsulfoniopropionate-catabolizing bacteria.

    Science.gov (United States)

    Wang, Peng; Cao, Hai-Yan; Chen, Xiu-Lan; Li, Chun-Yang; Li, Ping-Yi; Zhang, Xi-Ying; Qin, Qi-Long; Todd, Jonathan D; Zhang, Yu-Zhong

    2017-09-01

    Dimethylsulfoniopropionate (DMSP) cleavage, yielding dimethyl sulfide (DMS) and acrylate, provides vital carbon sources to marine bacteria, is a key component of the global sulfur cycle and effects atmospheric chemistry and potentially climate. Acrylate and its metabolite acryloyl-CoA are toxic if allowed to accumulate within cells. Thus, organisms cleaving DMSP require effective systems for both the utilization and detoxification of acrylate. Here, we examine the mechanism of acrylate utilization and detoxification in Roseobacters. We propose propionate-CoA ligase (PrpE) and acryloyl-CoA reductase (AcuI) as the key enzymes involved and through structural and mutagenesis analyses, provide explanations of their catalytic mechanisms. In most cases, DMSP lyases and DMSP demethylases (DmdAs) have low substrate affinities, but AcuIs have very high substrate affinities, suggesting that an effective detoxification system for acylate catabolism exists in DMSP-catabolizing Roseobacters. This study provides insight on acrylate metabolism and detoxification and a possible explanation for the high Km values that have been noted for some DMSP lyases. Since acrylate/acryloyl-CoA is probably produced by other metabolism, and AcuI and PrpE are conserved in many organisms across all domains of life, the detoxification system is likely relevant to many metabolic processes and environments beyond DMSP catabolism. © 2017 John Wiley & Sons Ltd.

  6. In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Lihua; Lei, Zhiwen [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Xu, Chuanhui, E-mail: xuhuiyee@gxu.edu.cn [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, China(South China University of Technology), Guangzhou, 510640 (China)

    2016-02-15

    To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

  7. Allergic contact dermatitis from sculptured acrylic nails: special presentation with an airborne pattern

    Directory of Open Access Journals (Sweden)

    Paula Maio

    2012-05-01

    Full Text Available Methylmethacrylate was first reported in 1941 as a cause of contact dermatitis. Since then, occupational contact allergies to acrylates in dentistry, orthopedic surgery, printing industry and industry have been reported, but few reports are found in the literature as a consequence of the contact with sculptured artificial acrylic nails which are increasingly popular. We describe here 3 patients with contact allergy to acrylates in artificial sculptured nails. Patch tests were performed with the Portuguese baseline series of contact allergens and an extended series of acrylates were applied. In particular, we tested three female patients with allergic contact dermatitis from sculptured acrylic nails. Two of these patients were both customers and also technical nail beauticians. Two patients developed periungual eczema; one presented only with face and eyelid dermatitis had no other lesions. The tests showed positive reaction to 2-hydroxyethylmethacrylate (2-HEMA and 2-hydroxypropylmethacrylate (2-HPMA in all the three patients. Our cases demonstrate the variety of clinical presentations of allergic contact dermatitis from acrylic sculptured nails. They show the need to warn patients of persistent and sometimes permanent side effects of these products. They also emphasize the importance of cosmetic ingredient labeling.

  8. Controlled radical fluorination of poly(meth)acrylic acids in aqueous solution.

    Science.gov (United States)

    Dong, Yucheng; Wang, Zhentao; Li, Chaozhong

    2017-08-17

    Fluorinated alkenes exhibit very poor reactivity in copolymerization with non-fluorinated polar monomers such as acrylates. Herein we describe a convenient method for the synthesis of poly(vinyl fluoride-co-acrylic acid) and poly(2-fluoropropene-co-methacrylic acid) copolymers. Thus, the silver-catalyzed decarboxylative radical fluorination of poly(acrylic acid) with Selectfluor in water at room temperature affords poly(vinyl fluoride-co-acrylic acid) copolymers in high yields with well-defined molecular weights and polydispersities. A linear correlation is observed between the extent of fluorination and the amount of Selectfluor, indicating that the copolymer of virtually any monomer ratio can be readily accessed by controlling the amount of Selectfluor. This controlled decarboxylative fluorination is extended to poly(methacrylic acid), leading to well-defined poly(2-fluoropropene-co-methacrylic acid) copolymers.Fluorinated alkenes have very poor reactivity in copolymerizations with non-fluorinated polar monomers. Here the authors show silver-catalyzed decarboxylative radical fluorination of poly(acrylic acid) with Selectfluor in water at room temperature to form poly(vinyl fluoride-co-acrylic acid) copolymers.

  9. Intraventricular metastatic clear cell renal carcinoma.

    Science.gov (United States)

    Sava, I; Sava, Anca; Şapte, Elena; Mihailov, Claudia; Dumitrescu, Gabriela; Poeată, I; Sava, Florina; Haba, Danisia

    2013-01-01

    Intraventricular tumors represent a diagnostic problem, due to a wide range of differential diagnosis, with an important variability of tumoral histological types in adult and pediatric population. Patient, Our case is represented by a patient, aged 48 years, without any history of significant personal pathology, accusing nausea, vomiting, and intensive headache. In the morning, he became confused, having hallucinations for a short period of time, and has accused drowsiness for several weeks. Imaging (CT and MRI) shows a neoformation in the third ventricle, accompanied by bilateral lateral ventricles dilatation, with predominantly annular enhancement. During surgery, through the middle third transcallosal interhemispheric approach, it was revealed a reddish, well-demarcated intraventricular mass, well vascularized and with a firm consistency. Final pathologic diagnosis was metastatic clear cell renal carcinoma. Initial postoperative evolution was good, and then neurological and respiratory condition worsened as a bronchopneumonia lead to patient's death in 12 days after surgery. Clear cell carcinoma metastasis located in the third ventricle should be taken into consideration for patients presenting a single intraventricular lesion even they have no documented primary malignancy.

  10. Rapid spheroid clearing on a microfluidic chip.

    Science.gov (United States)

    Silva Santisteban, Tomas; Rabajania, Omid; Kalinina, Iana; Robinson, Stephen; Meier, Matthias

    2017-12-19

    Spheroids are three-dimensional (3D) cell cultures that aim to bridge the gap between the use of whole animals and cellular monolayers. Microfluidics is regarded as an enabling technology to actively control the chemical environment of 3D cell cultures. Although a wide variety of platforms have been developed to handle spheroid cultures, the development of analytical systems for spheroids remains a major challenge. In this study, we engineered a microfluidic large-scale integration (mLSI) chip platform for tissue-clearing and imaging. To enable handling and culturing of spheroids on mLSI chips, with diameters within hundreds of microns, we first developed a general rapid prototyping procedure, which allows scaling up of the size of pneumatic membrane valves (PMV). The presented prototyping method makes use of milled poly(methylmethacrylate) (PMMA) molds for obtaining semi-circular microchannels with heights up to 750 μm. Semi-circular channel profiles are required for the functioning of the commonly used PMVs in normally open configuration. Height limits to tens of microns for this channel profile on photolithographic molds have hampered the application of 3D tissue models on mLSI chips. The prototyping technique was applied to produce an mLSI chip for miniaturization, automation, and integration of the steps involved in the tissue clearing method CLARITY, including spheroid fixation, acrylamide hydrogel infiltration, temperature-initiated hydrogel polymerization, lipid extraction, and immuno-fluorescence staining of the mitochondrial protein COX-IV, and metabolic enzyme GAPDH. Precise fluidic control over the liquids in the spheroid culturing chambers allowed implementation of a local hydrogel polymerization reaction, exclusively within the spheroid tissue. Hydrogel-embedded spheroids undergo swelling and shrinkage depending on the pH of the surrounding buffer solution. A pH-jump from 8.5 to 5.5 shrinks the hydrogel-embedded spheroid volume by 108% with a rate

  11. Chelating compounds as potential flash rust inhibitors and melamine & aziridine cure of acrylic colloidal unimolecular polymers (CUPs)

    Science.gov (United States)

    Mistry, Jigar Kishorkumar

    Waterborne coatings on ferrous substrates usually show flash rusting which decreases the adhesion of the coating and the corrosion products can form a stain. Chelating compounds were investigated as potential flash rust inhibitors. Compounds being evaluated include amine alcohols, diamines and sulfur containing amines. A new corrosion inhibitor 2,5-bis(thioaceticacid)-1,3,4-thiadiazole (H2ADTZ) was synthesized and its performance characteristics were evaluated. It was noted that the observed structure of 1,3,4-thiadiazolidine-2,5-dithione (also known as 2,5-dimercapto-1,3,4-thiadiazole (DMTD or DMcT)) has been previously reported in three different tautomeric forms including -dithiol and -dithione. The relative stability of each form as well as the synthesis and characterization of the structures of mono- and dialkylated forms of 5-mercapto-1,3,4-thiadiazole-2(3H)-thione (MTT) were examined. The methods of X-ray crystallography, NMR spectroscopy and ab-initio electronic structure calculations were combined to understand the reactivity and structure of each compound. Polymers were synthesized with a 1:7 or 1:8 ratio of acrylic acid to acrylate monomers to produce an acid rich resin. The polymers were reduced and solvent stripped to produce Colloidal Unimolecular Polymers (CUPs). These particles are typically 3-9 nanometers in diameter depending upon the molecular weight. They were then formulated into a clear coating with either a melamine (bake) or an aziridine (ambient cure) and then cured. The melamine system was solvent free, a near zero VOC and the aziridine system was very low to near zero VOC. The coatings were evaluated for their MEK resistance, adhesion, hardness, gloss, flexibility, wet adhesion, abrasion and impact resistance properties.

  12. Bilateral clear cell sarcoma of the kidney

    Directory of Open Access Journals (Sweden)

    Wael Zekri

    2015-06-01

    Full Text Available Clear cell sarcoma of the kidney (CCSK accounts for 2–5% of all pediatric renal malignancies, and is known for its propensity to metastasize to bone and other sites. We are reporting two cases with bilateral CCSK that were diagnosed at our institution. One patient initially presented with bilateral renal masses, as well as pulmonary, hepatic and bone metastasis; while other present only with bilateral masses with no evident distant metastasis. Both patients received aggressive neo-adjuvant chemotherapy to decrease tumor size. One patient completed his designated treatment and initially showed complete remission (CR; eventually suffering from relapse. The other patient’s tumor progressed during the course of chemotherapy. Both cases manifested brain dissemination at the time of relapse or progression. This emphasizes the importance of staging stratification in CCSK. This also illustrates CCSK’s ability to metastasize to bone and other sites including the brain (a primary relapse site in our cases.

  13. Clear air turbulence over South Africa

    Science.gov (United States)

    de Villiers, M. P.; van Heerden, J.

    2001-03-01

    Clear air turbulence (CAT) at high altitude remains a hazard to aviation which can result in passenger injury and aircraft damage. Two limited surveys of CAT events over South Africa, 1993-1995 (inclusive) and 1998, are used to illustrate the most likely synoptic conditions under which CAT can be expected. A case study of CAT associated with an upper-air trough and a mountain wave is presented. The study also evaluates the effectiveness of the Ellrod Turbulence Index (ETI) derived from model data provided by the UK Met. Office. A forecast of ETI derived from the Global Spectral Model of the United States National Center for Environmental Prediction (NCEP) is also reviewed.

  14. Synthesis, characterization and antimicrobial activity of important heterocyclic acrylic copolymers

    Directory of Open Access Journals (Sweden)

    2008-10-01

    Full Text Available The acrylate monomer, 7-acryloyloxy-4-methyl coumarin (AMC has been synthesized by reacting 7-hydroxy-4-methyl coumarin, with acryloyl chloride in the presence of NaOH at 0–5°C. Copolymers of 7-acryloyloxy-4-methyl coumarin (AMC with vinyl acetate (VAc were synthesized in DMF (dimethyl formamide solution at 70±1°C using 2,2′-azobisisobutyronitrile (AIBN as an initiator with different monomer-to-monomer ratios in the feed. The copolymers were characterized by Fourier transform infra red (FTIR spectroscopy. The copolymer composition was evaluated by 1H-NMR (proton nuclear magnetic resonance and was further used to determine reactivity ratios. The monomer reactivity ratios for AMC (M1-VAc (M2 pair were determined by the application of conventional linearization methods such as Fineman-Ross (r1 = 0.6924; r2 = 0.6431, Kelen-Tüdõs (r1 = 0.6776; r2 = 0.6374 and extended Kelen-Tüdõs (r1 = 0.6657; r2 = 0.6256. Thermo gravimetric analysis showed that thermal decomposition of the copolymers occurred in single stage in the temperature range of 263–458°C. The molecular weights of the polymers were determined using gel permeation chromatography. The homo and copolymers were tested for their antimicrobial properties against selected microorganisms.

  15. Icephobicity of polydimethylsiloxane-b-poly(fluorinated acrylate)

    Energy Technology Data Exchange (ETDEWEB)

    Li, Hui [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); School of Chemistry and Chemical Engineering, Shandong Key Laboratory of Fluorine Chemistry and Chemical Engineering Materials, University of Jinan, Jinan 250022 (China); Li, Xiaohui; Luo, Chenghao; Zhao, Yunhui [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); Yuan, Xiaoyan, E-mail: yuanxy@tju.edu.cn [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China)

    2014-12-31

    A facile process to fabricate icephobic surfaces was developed by spin-coating the polydimethylsiloxane-b-poly(fluorinated acrylate) (PDMS-b-PFA) block copolymers on the substrate. The surface microstructure and chemical composition of the block copolymer films can be adjusted by changing the PDMS content. Icephobic properties of the copolymer surface were mainly ascribed to “flexible-hard” microphase separation and the ratio of fluorine to silicon. The appropriate microphase domain size and the fluorine/silicon ratio could weaken the interaction of ice and copolymer surface and delay icing of water droplets on the copolymer surface. The copolymers containing 15 wt.% PDMS showed the most outstanding icephobicity by depressing the interaction between ice and the copolymer surface. - Highlights: • PDMS-b-PFA block copolymers with different PDMS contents were synthesized. • Surface microstructure can be adjusted by changing the content of PDMS. • The ratio of fluorine/silicon increased with the decrease of the PDMS content. • Ice adhesion and shear strength were decreased by the synergistic effect of silicon and fluorine.

  16. Rat hindlimb joint immobilization with acrylic resin orthoses

    Directory of Open Access Journals (Sweden)

    C.A. da Silva

    2006-07-01

    Full Text Available The objective of the present study was to propose an orthosis of light material that would be functional for the animal and that would maintain only the ankle joint immobilized. Male Wistar rats (3 to 4 months old, 250-300 g were divided into 2 groups (N = 6: control and immobilized for 7 days. Rats were anesthetized with sodium pentobarbital (40 mg/kg weight and the left hindlimb was immobilized with the orthoses composed of acrylic resin model, abdominal belt and lateral supports. The following analyses were performed: glycogen content of the soleus, extensor digitorum longus, white gastrocnemius, red gastrocnemius, and tibialis anterior muscles by the phenol sulfuric method, and the weight, fiber area and intramuscular connective tissue of the soleus by the planimetric system. Data were analyzed statistically by the Kolmogorov-Smirnov, Student t and Wilcoxon tests. Immobilization decreased glycogen in all muscles (P < 0.05; soleus: 31.6%, white gastrocnemius: 56.6%, red gastrocnemius: 39%, extensor digitorum longus: 41.7%, tibialis anterior: 45.2% in addition to reducing soleus weight by 34% (P < 0.05. Furthermore, immobilization promoted reduction of the fiber area (43%, P < 0.05 and increased the connective tissue (200%, P < 0.05. The orthosis model was efficient comparing with another alternative immobilization model, like plaster casts, in promoting skeletal muscle alterations, indicating that it could be used as a new model in other studies related to muscle disuse.

  17. Fabricating of full denture acrylic protheses with palatine torus

    Directory of Open Access Journals (Sweden)

    Ima Hariyati

    2016-06-01

    Full Text Available Full denture acrylic protheses can substitute all maxillary or mandibulary teeth naturally. The objective of fabricating full denture protheses is to substitute the tissue lost that was occupied by teeth or connective tissue before ward. This is a case of a 43 year old female with lost of all her upper and lower teeth. At the maxilla there is a palatine torus spreading along the midline with 25 mm length, 10 mm width and 6mm height. She has never worn prothese before. The process of full denture protheses fabrication were carried out in several steps, starting from making anatomical impression  to get study model, making of individual stock tray, making functional impression to get working model, choosing the design, making of midline, making of bite rim, inserting the model on articulator, preparing artificial teeth arrangement, fitting the wax, countoring wax, flasking, boiling out, packing, curing, deflasking, finishing, polishing and inserting the protheses. The process of this full denture protheses fabrication used tin foil as reducer to prevent overpressure of the tissue around the thin torus area so the prothesis will be more comfortable for the patient. The result was the protheses can be used by the patient, nicely and comfortably.

  18. A stability study of plasma polymerized acrylic acid films

    Science.gov (United States)

    Cools, Pieter; Declercq, Heidi; De Geyter, Nathalie; Morent, Rino

    2018-02-01

    A medium pressure parallel-plate DBD set-up was used for the deposition of carboxylic acid-rich films using acrylic acid as precursor. A variety of discharge powers (21-33 W) and monomer flow rates (0.25-0.5 g/h) were applied to develop a range of coatings from highly unstable to completely stable in aqueous solutions. FT-IR and XPS were used to identify which coatings were stable under dynamic incubation conditions and what influence plasma operating parameters had on functional group preservation. White light interferometry was also used to calculate deposition rates (66-126 nm/min) and to determine the deposition regime (monomer deficient). Human foreskin fibroblasts were seeded onto the complete range of investigated samples and the effects of coating (in)stability on cell adhesion, viability and morphology were systematically studied. Results showed that the 27 W-0.25 g/h treatment conditions resulted in the most stable coatings. Although a concentration of only 0.7% of carboxylic acid groups was found under these experimental conditions, the positive effects of a highly acid-rich surface were still maintained as cell-material interactions were significantly enhanced.

  19. Acoustic Performance of Resilient Materials Using Acrylic Polymer Emulsion Resin

    Directory of Open Access Journals (Sweden)

    Haseog Kim

    2016-07-01

    Full Text Available There have been frequent cases of civil complaints and disputes in relation to floor impact noises over the years. To solve these issues, a substantial amount of sound resilient material is installed between the concrete slab and the foamed concrete during construction. A new place-type resilient material is made from cement, silica powder, sodium sulfate, expanded-polystyrene, anhydrite, fly ash, and acrylic polymer emulsion resin. Its physical characteristics such as density, compressive strength, dynamic stiffness, and remanent strain are analyzed to assess the acoustic performance of the material. The experimental results showed the density and the dynamic stiffness of the proposed resilient material is increased with proportional to the use of cement and silica powder due to the high contents of the raw materials. The remanent strain, related to the serviceability of a structure, is found to be inversely proportional to the density and strength. The amount of reduction in the heavyweight impact noise is significant in a material with high density, high strength, and low remanent strain. Finally, specimen no. R4, having the reduction level of 3 dB for impact ball and 1 dB for bang machine in the single number quantity level, respectively, is the best product to obtain overall acoustic performance.

  20. Photoinduced Acrylate Polymerization: Unexpected Reduction in Chain Branching.

    Science.gov (United States)

    Wenn, Benjamin; Reekmans, Gunter; Adriaensens, Peter; Junkers, Thomas

    2015-08-01

    The branching stemming from midchain radical formation in n-butyl acrylate polymerization is investigated via melt-state (13) C NMR measurements. The dependence of the degree of branching (DB) on the monomer conversion of the system is examined for photoinduced polymerizations, revealing a steady increase in branching with conversion. For polymerization at moderate light intensities, an increase in branching from 0.03% to 0.37% is observed for polymerizations at 60 °C, which is fivefold below the level of branching observed in thermally initiated polymerizations under otherwise identical reaction conditions. The reason for this overall reduction in branching remains momentarily unclear; yet, a strong dependence of branching on light intensity is observed. While polymerization under a 1 W LED lamp results at almost full monomer conversion in branching degrees of 0.22%, polymerization under a 400 W lamp yields 1.81% of chain branches. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    Science.gov (United States)

    Zakrevskyy, Yuriy; Cywinski, Piotr; Cywinska, Magdalena; Paasche, Jens; Lomadze, Nino; Reich, Oliver; Löhmannsröben, Hans-Gerd; Santer, Svetlana

    2014-01-01

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes' properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate - for the first time - complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  2. Radiation-induced synthesis of poly(acrylic acid) nanogels

    Science.gov (United States)

    Matusiak, Malgorzata; Kadlubowski, Slawomir; Ulanski, Piotr

    2018-01-01

    Nanogel is a two-component system of a diameter in the range of tens of nanometers, consisting of an intramolecularly crosslinked polymer chain and solvent, typically water, filling the space between segments of the macromolecule. Microgels are bigger than nanogels and their size range is between 100 nm to 100 μm. One of the methods used for synthesizing nanogels is linking the segments of a single macromolecule with the use of ionizing radiation, by intramolecular recombination of radiation-generated polymer radicals. The main advantage of this technique is absence of monomers, catalysts, surfactants or crosslinking agents. This method is an interesting alternative way of synthesizing polymeric carriers for biomedical applications. The aim of the study was radiation synthesis and characterization of poly(acrylic acid) - PAA - nanogels and microgels. The physico-chemical properties were described by determination of weight-average molecular weight and dimensions (radius of gyration, hydrodynamic radius) of the nanogels and microgels. Influence of polymer concentration and dose on these parameters was analyzed. Adjusting the PAA concentration and absorbed dose, one can control the molecular weight and dimensions of nanogels. The solutions of PAA were irradiated with two sources of ionizing radiation: γ-source and electron accelerator. The former method yields mainly microgels due to prevailing intermolecular crosslinking, while the latter promotes intramolecular recombination of PAA-derived radicals and in consequence formation of nanogels. In the future radiation-synthesized PAA nanogels, after functionalization, will be tested as carriers for delivering radionuclides to the tumor cells.

  3. INFIBRA: machine vision inspection of acrylic fiber production

    Science.gov (United States)

    Davies, Roger; Correia, Bento A. B.; Contreiras, Jose; Carvalho, Fernando D.

    1998-10-01

    This paper describes the implementation of INFIBRA, a machine vision system for the inspection of acrylic fiber production lines. The system was developed by INETI under a contract from Fisipe, Fibras Sinteticas de Portugal, S.A. At Fisipe there are ten production lines in continuous operation, each approximately 40 m in length. A team of operators used to perform periodic manual visual inspection of each line in conditions of high ambient temperature and humidity. It is not surprising that failures in the manual inspection process occurred with some frequency, with consequences that ranged from reduced fiber quality to production stoppages. The INFIBRA system architecture is a specialization of a generic, modular machine vision architecture based on a network of Personal Computers (PCs), each equipped with a low cost frame grabber. Each production line has a dedicated PC that performs automatic inspection, using specially designed metrology algorithms, via four video cameras located at key positions on the line. The cameras are mounted inside custom-built, hermetically sealed water-cooled housings to protect them from the unfriendly environment. The ten PCs, one for each production line, communicate with a central PC via a standard Ethernet connection. The operator controls all aspects of the inspection process, from configuration through to handling alarms, via a simple graphical interface on the central PC. At any time the operator can also view on the central PC's screen the live image from any one of the 40 cameras employed by the system.

  4. Synthesis of acrylates and methacrylates from coal-derived syngas

    Energy Technology Data Exchange (ETDEWEB)

    Spivey, J.J.; Gogate, M.R.; Jang, B.W.L. [Bechtel, San Francisco, CA (United States)] [and others

    1995-12-31

    Acrylates and methacrylates are among the most widely used chemical intermediates in the world. One of the key chemicals of this type is methyl methacrylate. Of the 4 billion pounds produced each year, roughly 85% is made using the acetone-cyanohydrin process, which requires handling of large quantities of hydrogen cyanide and produces ammonium sulfate wastes that pose an environmental disposal challenge. The U.S. Department of Energy and Eastman Chemical Company are sharing the cost of research to develop an alternative process for the synthesis of methyl methacrylate from syngas. Research Triangle Institute is focusing on the synthesis and testing of active catalysts for the condensation reactions, and Bechtel is analyzing the costs to determine the competitiveness of several process alternatives. Results thus far show that the catalysts for the condensation of formaldehyde and the propionate are key to selectively producing the desired product, methacrylic acid, with a high yield. These condensation catalysts have both acid and base functions and the strength and distribution of these acid-base sites controls the product selectivity and yield.

  5. Rupture of a highly stretchable acrylic dielectric elastomer

    Science.gov (United States)

    Pharr, George; Sun, Jeong-Yun; Suo, Zhigang

    2012-02-01

    Dielectric elastomers have found widespread application as energy harvesters, actuators, and sensors. In practice these elastomers are subject to large tensile stretches, which potentially can lead to mechanical fracture. In this study, we have examined fracture properties of the commercial acrylic elastomer VHB 4905. We have found that inserting a pre-cut into the material drastically reduces the stretch at rupture from λrup = 9.43±1.05 for pristine samples down to only λrup = 3.63±0.45 for the samples with a pre-cut. Furthermore, using ``pure-shear'' test specimens with a pre-crack, we have measured the fracture energy and stretch at rupture as a function of the sample geometry. The stretch at rupture was found to decrease with sample height, which agrees with an analytical prediction. Additionally, we have measured the fracture energy as a function of stretch-rate. The apparent fracture energy was found to increase with stretch-rate from γ 1500 J/m^2 to γ 5000 J/m^2 for the investigated rates of deformation. This phenomenon is due to viscoelastic properties of VHB 4905, which result in an apparent stiffening for sufficiently large stretch-rates.

  6. Strategic design and fabrication of acrylic shape memory polymers

    Science.gov (United States)

    Park, Ju Hyuk; Kim, Hansu; Ryoun Youn, Jae; Song, Young Seok

    2017-08-01

    Modulation of thermomechanics nature is a critical issue for an optimized use of shape memory polymers (SMPs). In this study, a strategic approach was proposed to control the transition temperature of SMPs. Free radical vinyl polymerization was employed for tailoring and preparing acrylic SMPs. Transition temperatures of the shape memory tri-copolymers were tuned by changing the composition of monomers. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analyses were carried out to evaluate the chemical structures and compositions of the synthesized SMPs. The thermomechanical properties and shape memory performance of the SMPs were also examined by performing dynamic mechanical thermal analysis. Numerical simulation based on a finite element method provided consistent results with experimental cyclic shape memory tests of the specimens. Transient shape recovery tests were conducted and optical transparence of the samples was identified. We envision that the materials proposed in this study can help develop a new type of shape-memory devices in biomedical and aerospace engineering applications.

  7. Optical clearing mechanisms characterization in muscle

    Directory of Open Access Journals (Sweden)

    Luís Oliveira

    2016-09-01

    Full Text Available Optical immersion clearing is a technique that has been widely studied for more than two decades and that is used to originate a temporary transparency effect in biological tissues. If applied in cooperation with clinical methods it provides optimization of diagnosis and treatment procedures. This technique turns biological tissues more transparent through two main mechanisms — tissue dehydration and refractive index (RI matching between tissue components. Such matching is obtained by partial replacement of interstitial water by a biocompatible agent that presents higher RI and it can be completely reversible by natural rehydration in vivo or by assisted rehydration in ex vivo tissues. Experimental data to characterize and discriminate between the two mechanisms and to find new ones are necessary. Using a simple method, based on collimated transmittance and thickness measurements made from muscle samples under treatment, we have estimated the diffusion properties of glucose, ethylene glycol (EG and water that were used to perform such characterization and discrimination. Comparing these properties with data from literature that characterize their diffusion in water we have observed that muscle cell membrane permeability limits agent and water diffusion in the muscle. The same experimental data has allowed to calculate the optical clearing (OC efficiency and make an interpretation of the internal changes that occurred in muscle during the treatments. The same methodology can now be used to perform similar studies with other agents and in other tissues in order to solve engineering problems at design of inexpensive and robust technologies for a considerable improvement of optical tomographic techniques with better contrast and in-depth imaging.

  8. The Effect of Double Crosslinker on Precipitation Polymerization of Poly(acrylic acid

    Directory of Open Access Journals (Sweden)

    Hajar Es-haghi

    2014-06-01

    Full Text Available Cross-linked poly(acrylic acids were prepared by dual cross-linkers via precipitation polymerization method in a binary organic solvent. Polyethylene glycol diacrylate (PEGDA-400 as a long-chain cross-linker and di(trimethylol propane tetraacrylate (DTMPTA as multifunctional cross-linker were used. PEGDA-400 was utilized to increase thickening properties and DTMPTA was used to improve the gel strength. The dual cross-linkers effect on the sample features (i.e., equilibrium swelling, thickening properties and rheological properties was investigated. Maximum amount of swelling was obtained by a high percentage of long-chain cross-linker. The apparent viscosity of the microgels was measured to determine their thickening properties for aqueous media. Maximum viscosity occurred at DT25-PE75 which was dependent on the type of cross-linkers in the polymer structure. The Flory-Rehner equation (from swelling ratio data and rubber elasticity theory (from rheometry data were used to discuss the network structure of the polymer. Increasing density of the network was shown by a sample containing high percentage of a four-functional cross-linker. The rheological properties of the cross-linked polymers were measured to determine storage modulus (strength network. The rheological behaviors demonstrated that the synthesized polymer containing a high amount of four-functional cross-linker had higher storage modulus (G′ than other samples. In addition the consistency coefficient (m and flow behavior index (n parameters of Ostwald equation were investigated as well. As a result, n values in each sample were found to be smaller than 1 and these results were fitted clearly with the pseudoplastic model. Apparent and rotational viscosities were used to determine the optimal cross-linker type (synthesized sample contained a high percentage of long-chain cross-linker.

  9. The effects of barium sufate and iodide compound on the characteristics of dental acrylic resins

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yong Keun; Lee, Keon Il; Jung, Sung Woo [Dept. of Oral Radiology, College of Dentistry, Wonkwang University, Iksan(Korea, Republic of)

    1996-08-15

    Aspiratin or swallowing foreign bodies is a common occurrence. If they are wholly or partly radiopaque, their localization in and progress through the gastrointestinal tract can be more effective. Of the dental origin foreign materials swallowed, the most common things are fragments of anterior maxillary partial denture. But the radiopacity of denture base resins is not sufficient to determine the location of the objects. The purpose of this study was to develop a radiopaque dental acrylic resin, which has clinically detectable radiopacity with minimal change of mechanical properties and color. the radiopacity, color change (CIE E) and microhardness of acrylic resins were determined after mixing barium sulfate or iolide compound. Thermocycling course was conducted to deter mine the change of characteristic of resins after using for a long time I the mouth. Five or ten percent of barium sulfa te to total weight of cured material was mixed with heat curing dental acrylic resin or chemically curing orthodontic re sin. In the case of iodide compound, the mixing ratio was two or three percent. After mixing the high radiopaque material s, resin was cured to 20X20X2 mm plate, polished with 600 sand paper and finally polished with Microcloth (Buehler). T he specimens were thermocycled in 5 and 55 degree distilled water for 2,000 times, and the measurement of radiopacity, color and Vickers hardness was repeated every 500 times thermocycling. The radiopacity of specimens on the X-ray films was measured with densitometer (X-rite). The color change was determined with differential colorimeter (Model TC-6FX, Tokyo Denshoku), and the Vickers hardness number was measured with microhardness tester (Mitsuzawa). The following results were obtained : 1. All the three variables, the kinds of acrylic resins, the mixing or the kinds radiopaque materials and thermocycling , had combined effect on the radiopacity of the dental acrylic resins (p<0.01). 2. The two variables, the mixing or

  10. Preparation and magnetic properties of polymer magnetic composites based on acrylate resin filled with nickel plating graphite nanosheets

    Science.gov (United States)

    Zhang, Yi; Qi, Shuhua; Zhang, Fan; Yang, Yongqing; Duan, Guochen

    2011-11-01

    Nickel plating graphite nanosheets (Ni/GNs) were prepared by electroless plating method using graphite nanosheets (GNs). Then a novel polymer magnetic composites based on acrylate pressure-sensitive adhesive (acrylate PSA) filled with Ni/GNs were fabricated by solution blend method. The Ni/GNs and acrylate PSA/Ni/GNs composites were characterized by scanning electron microscope (SEM)/energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and transmission electron microscope (TEM). All results showed that relatively uniform and compact Ni layer is successfully coated onto GNs under the given conditions, furthermore, Ni/GNs are homogeneously dispersed in acrylate PSA. The VSM results showed that the saturation magnetization of acrylate PSA/Ni/GNs composites increases with an increasing content of Ni/GNs while the coercivity decreases with an increasing content of Ni/GNs. When the content of GNs is 20 wt%, acrylate PSA/Ni/GNs composites exhibites good mechanical properties.

  11. Occupational allergic contact dermatitis caused by photobonded sculptured nails and a review of (meth) acrylates in nail cosmetics.

    Science.gov (United States)

    Kanerva, L; Lauerma, A; Estlander, T; Alanko, K; Henriks-Eckerman, M L; Jolanki, R

    1996-06-01

    Mono(meth)acrylates (monoacrylates and monomethacrylates) are moderate to strong sensitizers. They are used in the production of a great variety of polymers, including nail cosmetics. A patient who became occupationally sensitized to photobonded sculptured nails is reported. Detailed patch testing and analyses of the patient's nail cosmetics containing mono(meth)acrylates clarified the cause of her hand and face dermatitis. The current knowledge on mono(meth)acrylates in nail cosmetics is also reviewed. Patch testings with conventional methods, including patch testing with the patient's own substances, were performed. The patient's nail cosmetics suspected of containing mono(meth)acrylates were analyzed with gas chromatography/mass spectrometry analysis. In the (meth)acrylate series, 15 of the 31 (meth)acrylate compounds tested gave an allergic reaction: 2 acrylates, 5 methacrylates, 3 dimethacrylates, and 5 diacrylates. Epoxy diacrylates, cyanoacrylate, triacrylates, and methacrylic acid were negative. Three of seven of her own nail cosmetic preparations contained mono(meth)acrylates as revealed by the gas chromatography/mass spectrometry analysis, and these also gave allergic patch test reactions, namely, the nail liquid, nail hardener, and UV-cured nail gel. The patient probably had been sensitized to the following (meth)acrylate compounds from her nail cosmetics: tripropylene glycol diacrylate and methyl acrylate from her photobonded nail gel; ethyl methacrylate, triethylene glycol dimethacrylate, and methyl methacrylate from her nail liquid; and butyl methacrylate from her nail hardener. She was probably also sensitized to the rare sensitizer aliphatic urethane diacrylate, but the source was not verified. Because nail cosmetics containing mono(meth)acrylates are strong sensitizers, both the workers and the customers should be aware of their sensitizing capacity; they should use no-touch techniques regarding the skin before the mono(meth)acrylates are

  12. Aqueous Heck cross-coupling preparation of acrylate-modified nucleotides and nucleoside triphosphates for polymerase synthesis of acrylate-labeled DNA.

    Science.gov (United States)

    Dadová, Jitka; Vidláková, Pavlína; Pohl, Radek; Havran, Luděk; Fojta, Miroslav; Hocek, Michal

    2013-10-04

    Aqueous-phase Heck coupling methodology was developed for direct attachment of butyl acrylate to 5-iodoracil, 5-iodocytosine, 7-iodo-7-deazaadenine, and 7-iodo-7-deazaguanine 2'-deoxyribonucleoside 5'-O-monophosphates (dNMPs) and 5'-O-triphosphates (dNTPs) and compared with the classical approach of phosphorylation of the corresponding modified nucleosides. The 7-substituted 7-deazapurine nucleotides (dA(BA)MP, dA(BA)TP, dG(BA)MP, and dG(BA)TP) were prepared by the direct Heck coupling of nucleotides in good yields (35-55%), whereas the pyrimidine nucleotides reacted poorly and the corresponding BA-modified dNTPs were prepared by triphosphorylation of the modified nucleosides. The acrylate-modified dN(BA)TPs (N = A, C, and U) were good substrates for DNA polymerases and were used for enzymatic synthesis of acrylate-modified DNA by primer extension, whereas dG(BA)TP was an inhibitor of polymerases. The butyl acrylate group was found to be a useful redox label giving a strong reduction peak at -1.3 to -1.4 V in cyclic voltammetry.

  13. Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins

    Science.gov (United States)

    da SILVA, Paulo Maurício Batista; ACOSTA, Emílio José Tabaré Rodríguez; JACOBINA, Matheus; PINTO, Luciana de Rezende; PORTO, Vinícius Carvalho

    2011-01-01

    Objective Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. Material and Methods Sixty disc-shaped specimens (40 mm x 3 mm) were fabricated from two different brands (Artiplus and Trilux) of denture tooth acrylic resin. The specimens from each brand (n=30) were randomly divided into 6 groups (n=5) and immersed in the following solutions: distilled water (control group) and 5 disinfecting solutions (1% sodium hypochlorite, 2% sodium hypochlorite, 5.25% sodium hypochlorite, 2% glutaraldehyde, and 4% chlorhexidine gluconate). Tooth color measurements were made by spectrophotometry. Before disinfection, the initial color of each tooth was recorded. Further color measurements were determined after subjecting the specimens to 7, 21, 30, 45, 60, and 90 immersion cycles in each tested solution. Color differences (ΔE*) were determined using the CIE L*a*b* color system. Data were analyzed using two-way repeated measures analysis of variance (ANOVA) followed by Tukey tests. The significance level was set at 5%. Results There were statistically significant differences in ΔE* among the 5 disinfectants and water during the 90 cycles of immersion for both denture tooth acrylic resins. Distilled water promoted the greatest color change in both denture tooth acrylic resins, nevertheless none of tested disinfectants promoted ΔE* values higher than 1.0 on these acrylic materials during the 90 cycles of disinfection. Conclusions Repeated immersion cycles in disinfecting solutions alter ∆E* values, however these values do not compromise the color of the tested denture tooth acrylic resins because they are imperceptible to the human eye. PMID:22230997

  14. Comparison of bond strength of composite and acrylic teeth to heat-cured and

    Directory of Open Access Journals (Sweden)

    Amirjan A

    2011-02-01

    Full Text Available "nBackground and Aims: Failure of bonding between artificial teeth and denture base material is a considerable problem for patients who wear dentures. Because of the cost of denture repair and the expensive price of foreign artificial teeth, this study was designed to compare the bond strength of composite and acrylic artificial teeth with heat-cured and auto-polymerized denture base resins."nMaterials and Methods: In this experimental and in vitro study, two type of acrylic resin (heat-cured: Selectaplus H/ Trevalon, Dentsply and auto-polymerized: Rapid Repair, Dentsply and four artificial teeth (acrylic Marjan New, composite Glamour teeth which both of them are Iranian and Ivoclar acrylic and composite teeth were used. Therefore, 8 groups of 14 specimens each were evaluated. A shear bond strenghth test in a Universal Testing Machine was used. Data were analyzed using the 2-way ANOVA test."nResults: The bond strengths of acrylic teeth (Marjan New and Ivoclar to heat-cured resin were similar (P=0.632 and statistically higher than those of composite teeth (Glamour and Ivoclar. Acrylic teeth (Marjan New and Ivoclar and Glamour teeth had similar bond strength to auto-polymerized resin, which showed the highest bond strength values. Ivoclar composite teeth showed significantly the lowest bond strength (P<0.05. All acrylic teeth had the highest mean bond strengths to heat-cured resin which were significantly different from that of "nauto-polymerized resin (P<0.05. However, the bond strengths of all composite teeth to both denture base resins were not significantly different (P>0.05."nConclusion: Based on the results of this study, the type of denture base material and artificial tooth may influence the failure load.

  15. Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins.

    Science.gov (United States)

    Silva, Paulo Maurício Batista da; Acosta, Emílio José Tabaré Rodríguez; Jacobina, Matheus; Pinto, Luciana de Rezende; Porto, Vinícius Carvalho

    2011-01-01

    Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. Sixty disc-shaped specimens (40 mm x 3 mm) were fabricated from two different brands (Artiplus and Trilux) of denture tooth acrylic resin. The specimens from each brand (n=30) were randomly divided into 6 groups (n=5) and immersed in the following solutions: distilled water (control group) and 5 disinfecting solutions (1% sodium hypochlorite, 2% sodium hypochlorite, 5.25% sodium hypochlorite, 2% glutaraldehyde, and 4% chlorhexidine gluconate). Tooth color measurements were made by spectrophotometry. Before disinfection, the initial color of each tooth was recorded. Further color measurements were determined after subjecting the specimens to 7, 21, 30, 45, 60, and 90 immersion cycles in each tested solution. Color differences (ΔE*) were determined using the CIE L*a*b* color system. Data were analyzed using two-way repeated measures analysis of variance (ANOVA) followed by Tukey tests. The significance level was set at 5%. There were statistically significant differences in ΔE* among the 5 disinfectants and water during the 90 cycles of immersion for both denture tooth acrylic resins. Distilled water promoted the greatest color change in both denture tooth acrylic resins, nevertheless none of tested disinfectants promoted ΔE* values higher than 1.0 on these acrylic materials during the 90 cycles of disinfection. Repeated immersion cycles in disinfecting solutions alter ΔE* values, however these values do not compromise the color of the tested denture tooth acrylic resins because they are imperceptible to the human eye.

  16. Effect of repeated immersion solution cycles on the color stability of denture tooth acrylic resins

    Directory of Open Access Journals (Sweden)

    Paulo Maurício Batista da Silva

    2011-12-01

    Full Text Available OBJECTIVE: Chemical solutions have been widely used for disinfection of dentures, but their effect on color stability of denture tooth acrylic resins after repeated procedures is still unclear. The aim of this in vitro study was to evaluate whether repeated cycles of chemical disinfectants affected the color stability of two denture tooth acrylic resins. MATERIAL AND METHODS: Sixty disc-shaped specimens (40 mm x 3 mm were fabricated from two different brands (Artiplus and Trilux of denture tooth acrylic resin. The specimens from each brand (n=30 were randomly divided into 6 groups (n=5 and immersed in the following solutions: distilled water (control group and 5 disinfecting solutions (1% sodium hypochlorite, 2% sodium hypochlorite, 5.25% sodium hypochlorite, 2% glutaraldehyde, and 4% chlorhexidine gluconate. Tooth color measurements were made by spectrophotometry. Before disinfection, the initial color of each tooth was recorded. Further color measurements were determined after subjecting the specimens to 7, 21, 30, 45, 60, and 90 immersion cycles in each tested solution. Color differences (ΔE* were determined using the CIE L*a*b* color system. Data were analyzed using two-way repeated measures analysis of variance (ANOVA followed by Tukey tests. The significance level was set at 5%. RESULTS: There were statistically significant differences in ΔE* among the 5 disinfectants and water during the 90 cycles of immersion for both denture tooth acrylic resins. Distilled water promoted the greatest color change in both denture tooth acrylic resins, nevertheless none of tested disinfectants promoted ΔE* values higher than 1.0 on these acrylic materials during the 90 cycles of disinfection. CONCLUSIONS: Repeated immersion cycles in disinfecting solutions alter ΔE* values, however these values do not compromise the color of the tested denture tooth acrylic resins because they are imperceptible to the human eye.

  17. Degradation of back surface acrylic mirrors for low concentration and mirror-augmented photovoltaics

    Science.gov (United States)

    Murray, Myles P.; Bruckman, Laura S.; Gordon, Devin; Richardson, Samuel; Reinbolt, Greg; Schuetz, Mark; French, Roger H.

    2012-10-01

    Back-surface acrylic mirrors can be used in low concentration and mirror augmented photovoltaics (LCPV, MAPV) to increase the irradiance on a module. Back-surface mirrors can spectrally filter incoming solar radiation reducing the ultraviolet (UV) and infrared (IR) load on the module, while useful radiation is coupled into a module or photovoltaic cell. Degradation of these mirrors can occur from UV induced photodegradative processes and metallization corrosion. Environmental stresses such as humidity, thermal cycling and exposure to corrosive substances can cause an increase in scattering, reducing mirror performance. In order to increase the lifetime and durability of back-surface acrylic mirrors a better understanding of the degradation modes is necessary. In a study of acrylic back-surface mirrors for LCPV and MAPV applications, optical properties and bidirectional scattering distribution functions (BSDF) were investigated and correlated to simulated exposure protocols. Formulations of Poly(methyl methacrylate) (PMMA) with differing concentration of UV absorbers were used for the aluminum backsurface acrylic mirrors. The formulations of aluminum back-surface acrylic mirrors were exposed in a QUV accelerated weathering tester (QLabs) to ASTM G154 Cycle 4. Total and diffuse reflectance spectra were measured for each mirror under exposure using a diffuse reflectance accessory (DRA) from 180-1800 nm on a Varian Cary 6000i at defined dose intervals. The total reflectance losses in the 250-400 nm region were greater and diffuse-only reflectance increased for formulations of acrylic mirrors that contained the least amount of UV stabilizer after each dose of QUV exposure. Acrylic back-surface mirrors were exposed to salt fog corrosion and QUV and were analyzed using BSDF. There was an increase in scattering from roughening of the mirror surface after exposure to the corrosive environment.

  18. Sensitization and development of allergic contact dermatitis caused by a single contact with an electrosurgical grounding plate containing acrylates.

    Science.gov (United States)

    Borelli, S; Nestlé, F O

    1998-01-01

    Acrylates are known as potent sensitizers which can cause sensitization even during patch testing. A single exposure to concentrated acrylates can induce primary sensitization and contact dermatitis. Here we describe a 50-year-old man who developed contact dermatitis at the site of an electrosurgical grounding plate 2 weeks after orthopedic surgery. Patch testing revealed positive reactions to the electrosurgical plate and its components hydroxyethyl acrylate and hydroxyethyl methacrylate. As the patient has never had contact with acrylate-containing materials before, there is a high probability of primary sensitization by a single contact with the grounding plate during surgery.

  19. Fabrication of surface-structure controlled photopatterns upon transparent silica-acryl nanohybrid films with enhanced thermal and mechanical properties

    National Research Council Canada - National Science Library

    Dong Jun Kang; Dong Hee Han; Dong Pil Kang; Jae Won Yoo; Byeong Uk Kim

    2008-01-01

    Organic-inorganic nanohybrid materials were successfully fabricated from organically modified colloidal-silica nanoparticles synthesized through the sol-gel process and using the modified acryl resin...

  20. Water-soluble antioxidant derivative poly(triethylene glycol methyl acrylate-co-α-tocopheryl acrylate) as a potential prodrug to enable localized neuroprotection.

    Science.gov (United States)

    Cao, Y; He, W

    2013-01-01

    Implantable microelectrode arrays (MEA) hold enormous hope for individuals with sensory or motor deficits. However, long-term function of MEA remains a critical hurdle. The objective of this study was to synthesize an antioxidant prodrug that can be delivered to the neural tissue around the implant and present a pharmacological depot to combat the injurious oxidative stress around the MEA. In this report, monomers of triethylene glycol methyl acrylate and α-tocopheryl acrylate, a synthetic derivative of the antioxidant α-tocopherol (vitamin E, Ve), were copolymerized to obtain poly(triethylene glycol methyl acrylate-co-α-tocopheryl acrylate) (PVT) with different compositions. In contrast to the poor water solubility of Ve, solubility of the PVT prodrug in water can reach as high as 3.1 mg ml(-1) (equivalent to 500 μM Ve) by tuning the copolymer composition. To demonstrate the applicability of the prodrug for MEA implants, PVT was successfully deposited on silicon substrates with poly(acrylic acid) (PAA) or tannic acid (TA) using the layer-by-layer technique mediated by hydrogen bonding. Ellipsometry and quartz crystal microbalance data showed that the multilayers of PAA/PVT were destructible at physiological pH. In contrast, multilayers of TA/PVT were stable. The PVT prodrug was non-cytotoxic toward A172 human astrocytes. Furthermore, PVT was able to protect astrocytes against oxidative stress exerted by H(2)O(2) in vitro. Using a free radical scavenging assay, the protection mechanism was attributed to the hydrolysis of the labile ester linkage and release of the active Ve. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  1. Comparative evaluation of surface porosities in conventional heat polymerized acrylic resin cured by water bath and microwave energy with microwavable acrylic resin cured by microwave energy

    Directory of Open Access Journals (Sweden)

    Sunint Singh

    2013-01-01

    Full Text Available Background: Conventional heat cure poly methyl methacrylate (PMMA is the most commonly used denture base resin despite having some short comings. Lengthy polymerization time being one of them and in order to overcome this fact microwave curing method was recommended. Unavailability of specially designed microwavable acrylic resin made it unpopular. Therefore, in this study, conventional heat cure PMMA was polymerized by microwave energy. Aim and Objectives: This study was designed to evaluate the surface porosities in PMMA cured by conventional water bath and microwave energy and compare it with microwavable acrylic resin cured by microwave energy. Materials and Methods: Wax samples were obtained by pouring molten wax into a metal mold of 25 mm × 12 mm × 3 mm dimensions. These samples were divided into three groups namely C, CM, and M. Group C denotes conventional heat cure PMMA cured by water bath method, CM denotes conventional heat cure PMMA cured by microwave energy, M denotes specially designed microwavable acrylic denture base resin cured by microwave energy. After polymerization, each sample was scanned in three pre-marked areas for surface porosities using the optical microscope. As per the literature available, this instrument is being used for the first time to measure the porosity in acrylic resin. It is a reliable method of measuring area of surface pores. Portion of the sample being scanned is displayed on the computer and with the help of software area of each pore was measured and data were analyzed. Results: Conventional heat cure PMMA samples cured by microwave energy showed maximum porosities than the samples cured by conventional water bath method and microwavable acrylic resin cured by microwave energy. Higher percentage of porosities was statistically significant, but well within the range to be clinically acceptable. Conclusion: Within the limitations of this in-vitro study, conventional heat cure PMMA can be cured by

  2. Development of carboxymethyl cellulose acrylate for various biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Pal, Kunal [Materials Science Centre, Indian Institute of Technology, Kharagpur 721302 (India); Banthia, A K [Materials Science Centre, Indian Institute of Technology, Kharagpur 721302 (India); Majumdar, D K [Delhi Institute of Pharmaceutical Sciences and Research, Formerly College of Pharmacy, University of Delhi, Pushp Vihar, Sector III, New Delhi 110017 (India)

    2006-06-15

    The purpose of this work is to prepare a pH-sensitive hydrogel membrane of sodium carboxymethyl cellulose acrylate for drug delivery and other biomedical applications. The hydrogel was made by esterification of sodium carboxymethyl cellulose (SCMC) and acryloyl chloride (ACl). The esterified product was characterized by FTIR spectroscopy and XRD. Swelling, hemocompatibility, water vapor transmission rate, contact angle and diffusional studies were also done. Biocompatibility of the membrane was established by quantification of cell growth of L929 cells and mice splenocytes. The FTIR spectrum of the hydrogel suggested the formation of ester bonds between the hydroxyl groups of sodium carboxymethyl cellulose and the carbonyl group of acryloyl chloride. Water vapor transmission rate, hemocompatibility, contact angle and swelling studies indicated that the hydrogel can be tried as a wound dressing material. The hydrogel showed pH-dependent swelling behavior arising from the acidic pendant group in the polymer network. The permeability of the hydrogel membrane produced, as shown by salicylic acid diffusion, increased in response to an increase in pH of the external medium. The hydrogel membrane was permeable to salicylic acid at pH 7.2 but not at pH 2.0 (0.01N HCl). The effect of changes of pH on the hydrogel's permeability was found to be reversible. The hydrogel membrane was found to be compatible with the L929 mice fibroblast cell line and mice splenocytes. The esterified product of SCMC and ACl swells on increase of pH indicating its possible use in a pH-sensitive drug delivery system and as a wound dressing material.

  3. Development of carboxymethyl cellulose acrylate for various biomedical applications

    Science.gov (United States)

    Pal, Kunal; Banthia, A. K.; Majumdar, D. K.

    2006-06-01

    The purpose of this work is to prepare a pH-sensitive hydrogel membrane of sodium carboxymethyl cellulose acrylate for drug delivery and other biomedical applications. The hydrogel was made by esterification of sodium carboxymethyl cellulose (SCMC) and acryloyl chloride (ACl). The esterified product was characterized by FTIR spectroscopy and XRD. Swelling, hemocompatibility, water vapor transmission rate, contact angle and diffusional studies were also done. Biocompatibility of the membrane was established by quantification of cell growth of L929 cells and mice splenocytes. The FTIR spectrum of the hydrogel suggested the formation of ester bonds between the hydroxyl groups of sodium carboxymethyl cellulose and the carbonyl group of acryloyl chloride. Water vapor transmission rate, hemocompatibility, contact angle and swelling studies indicated that the hydrogel can be tried as a wound dressing material. The hydrogel showed pH-dependent swelling behavior arising from the acidic pendant group in the polymer network. The permeability of the hydrogel membrane produced, as shown by salicylic acid diffusion, increased in response to an increase in pH of the external medium. The hydrogel membrane was permeable to salicylic acid at pH 7.2 but not at pH 2.0 (0.01N HCl). The effect of changes of pH on the hydrogel's permeability was found to be reversible. The hydrogel membrane was found to be compatible with the L929 mice fibroblast cell line and mice splenocytes. The esterified product of SCMC and ACl swells on increase of pH indicating its possible use in a pH-sensitive drug delivery system and as a wound dressing material.

  4. Supercritical water oxidation of acrylic acid production wastewater.

    Science.gov (United States)

    Gong, Y M; Wang, S Z; Tang, X Y; Xu, D H; Ma, H H

    2014-01-01

    Supercritical water oxidation (SCWO) of wastewater from an acrylic acid manufacturing plant has been studied on a continuous flow experimental system, whose reactor was made of Hastelloy C-276. Experimental conditions included a reaction temperature (T) ranging from 673 to 773K, a residence time (t) ranging from 72.7 to 339s, a constant pressure (P) of 25 MPa and a fixed oxidation coefficient (alpha) of 2.0. Experimental results indicated that reaction temperature and residence time had significant influences on the oxidation reaction, and increasing the two operation parameters could improve both degradation of chemical oxygen demand (COD) and ammonia nitrogen (NH3-N). The COD removal efficiency could reach up to 98.73% at 25 MPa, 773 K and 180.1 s, whereas the destruction efficiency of NH3-N was only 43.71%. We further carried out a kinetic analysis considering the induction period through free radical chain mechanism. It confirms that the power-law rate equation for COD removal was 345 exp(-52200/RT)[COD]1.98[O2]0.17 and for NH3-N removal was 500 exp(-64492.19/RT)[NH3-N]1.87 [O2]0.03. Moreover, the induction time formulations for COD and NH3-N were suspected to be exp(38250/RT)/173 and exp(55690/RT)/15231, respectively. Correspondingly, induction time changed from 2.22 to 5.38 s for COD and 0.38 to 1.38 s for NH3-N. Owing to the catalysis of reactor inner wall surface, more than 97% COD removal was achieved in all samples.

  5. Clear Channel Assessment in Integrated Medical Environments

    Directory of Open Access Journals (Sweden)

    Hara Shinsuke

    2008-01-01

    Full Text Available Abstract Complementary WLAN and WPAN technologies as well as other wireless technologies will play a fundamental role in the medical environments to support ubiquitous healthcare delivery. This paper investigates clear channel assessment (CCA and its impact on the coexistence of WLAN (IEEE 802.11 high rate direct sequence spread spectrum (HR/DSSS PHY and WPAN (IEEE 802.15.4b in the 2.4 GHz industrial, scientific, and medical (ISM band. We derived closed-form expressions of both energy-based CCA and feature-based CCA. We qualified unequal sensing abilities between them and termed this inequality asymmetric CCA, which is different from the traditional "hidden node" or "exposed node" issues in the homogeneous network. The energy-based CCA was considered in the considered integrated medical environment because the 2.4 GHz ISM band is too crowded to apply feature-based CCA. The WPAN is oversensitive to the 802.11 HR/DSSS signals and the WLAN is insensitive to the 802.15.4b signals. Choosing an optimal CCA threshold requires some prior knowledge of the underlying signals. In the integrated medical environment we considered here, energy-based CCA can effectively avoid possible packet collisions when they are close within the "heterogeneous exclusive CCA range" (HECR. However, when they are separated beyond the HECR, WPAN can still sense the 802.11 HR/DSSS signals, but WLAN loses its sense to the 802.15.4b signals. The asymmetric CCA leads to WPAN traffic in a position secondary to WLAN traffic.

  6. Clear cell sarcoma: the Roswell Park experience.

    Science.gov (United States)

    Finley, J W; Hanypsiak, B; McGrath, B; Kraybill, W; Gibbs, J F

    2001-05-01

    Clear cell sarcoma of the tendons and aponeuroses (CCSTA) is an aggressive, rare soft-tissue tumor with approximately 300 reported cases. Although it appears to be histogenetically related to melanoma, its clinical behavior resembles soft tissue sarcoma with a propensity for lymph node metastases. We report our experience at a tertiary cancer center. Eight cases of CCSTA evaluated at Roswell Park Cancer Institute between 1970 and 1998 were reviewed retrospectively. Patient data analyzed included patient age, gender, anatomic location, size of tumor, development of local, regional and distant recurrence, and patient status at last follow up. Six of eight patients were alive at 2 years, while three of seven patients were alive at 5 years. Of the patients alive with no evidence of recurrence, two had tumors of less than 2 cm, and the remaining patient had incomplete information regarding tumor size. Five patients recurred within 2 years of definitive surgical management. Four had tumors > 5 cm. All five patients progressed to metastatic disease at a median follow up of 20 months (range 1-108 months) following definitive surgical management and all eventually died of their disease at a median of 3 months (range 0-24 months) from presentation with metastatic disease. Four of five patients with lesions > 5 cm received adjuvant chemotherapy with intent to cure, but all eventually died of disease at 4, 22, 34, and 41 months from initial presentation. CCSTA is an aggressive tumor of the soft tissues. Early recognition and management are associated with an excellent long-term prognosis. Tumors greater than 5 cm warrant aggressive surgical management and treatment, and are at high risk of the development of distant disease. Aggressive multiagent chemotherapy appeared to have no impact on outcome. Other adjuvant therapeutic options including immunotherapy should be investigated. Copyright 2001 Wiley-Liss, Inc.

  7. Surface morphology changes of acrylic resins during finishing and polishing phases

    Directory of Open Access Journals (Sweden)

    Glaucio Serra

    2013-12-01

    Full Text Available INTRODUCTION: The finishing and polishing phases are essential to improve smoothness and shining on the surface of acrylic resins used to make removable orthodontic appliances. A good surface finishing reduces roughness, which facilitates hygiene, prevents staining and provides greater comfort to the patients. OBJECTIVE: The aim of this paper was to analyze the changes on surface morphology of acrylic resins during finishing and polishing phases. METHODS: Thirty discs (10 mm in diameter and 5 mm in length were made with acrylic resin and randomly divided into ten groups. The control group did not receive any treatment while the other groups received gradual finishing and polishing. The last group received the entire finishing and polishing procedures. Surface morphology was qualitatively analyzed through scanning electron microscopy and quantitatively analyzed through a laser profilometer test. RESULTS: The acrylic resin surfaces without treatment showed bubbles which were not observed in the subsequent phases. Wearing out with multilaminated burs, finishing with wood sandpaper and finishing with water sandpaper resulted in surfaces with decreasing irregularities. The surfaces that were polished with pumice and with low abrasive liquids showed high superficial smoothness. CONCLUSION: Highly smooth acrylic resin surfaces can be obtained after mechanical finishing and polishing performed with multilaminated burs, wood sandpaper, water sandpaper, pumice and low abrasive liquids.

  8. Allergic contact dermatitis caused by acrylates and methacrylates--a 7-year study.

    Science.gov (United States)

    Ramos, Leonor; Cabral, Rita; Gonçalo, Margarida

    2014-08-01

    Allergic contact dermatitis (ACD) caused by (meth)acrylates is traditionally an occupational disease among dentists, printers, and fibreglass workers. With the use of artificial nails, cases have been reported both in nail technicians and in users. The aims of this study were to characterize ACD caused by (meth)acrylates, identify the responsible allergens, and assess the sensitivity of the patch test with 2-hydroxyethyl methacrylate (HEMA) for diagnosis. An observational and retrospective study (January 2006-April 2013) was performed, evaluating and correlating epidemiological and clinical parameters and positive patch test results with (meth)acrylates. Among 2263 patch tested patients, 122 underwent aimed testing with an extended (meth)acrylate series, and 37 showed positive and relevant reactions. Twenty-five cases (67.6%) were occupational. Hand eczema with pulpitis was observed in 32 patients. Twenty-eight cases were related to artificial nails, 3 were related to dental materials, and 2 were industrial workers. Oral lesions associated with dental prostheses were observed in 4 patients. Thirty-one patients reacted to more than one (meth)acrylate. In our sample, beauty technicians working with artificial nails were the most affected group (80% of occupational cases). HEMA detected 80.6% of our cases, and may be considered a good screening allergen. However, to perform an accurate diagnosis, it is safer to use a broader series of allergens. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  9. Synthesis of a novel acrylated abietic acid-g-bacterial cellulose hydrogel by gamma irradiation.

    Science.gov (United States)

    Abeer, Muhammad Mustafa; Amin, Mohd Cairul Iqbal Mohd; Lazim, Azwan Mat; Pandey, Manisha; Martin, Claire

    2014-09-22

    Acrylated abietic acid (acrylated AbA) and acrylated abietic acid-grafted bacterial cellulose pH sensitive hydrogel (acrylated AbA-g-BC) were prepared by a one-pot synthesis. The successful dimerization of acrylic acid (AA) and abietic acid (AbA) and grafting of the dimer onto bacterial cellulose (BC) was confirmed by 13C solid state NMR as well as FT-IR. X-ray diffraction analysis showed characteristic peaks for AbA and BC; further, there was no effect of increasing amorphous AA content on the overall crystallinity of the hydrogel. Differential scanning calorimetry revealed a glass transition temperature of 80°C. Gel fraction and swelling studies gave insight into the features of the hydrogel, suggesting that it was suitable for future applications such as drug delivery. Scanning electron microscopy observations showed an interesting interpenetrating network within the walls of hydrogel samples with the lowest levels of AA and gamma radiation doses. Cell viability test revealed that the synthesized hydrogel is safe for future use in biomedical applications. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Direct Synthesis of Hyperbranched Poly(acrylic acid-co-3-hydroxypropionate

    Directory of Open Access Journals (Sweden)

    Efkan Çatıker

    2015-01-01

    Full Text Available Hyperbranched poly(acrylic acid-co-3-hydroxypropionate (PAcHP was synthesized by base-catalyzed hydrogen transfer polymerization of acrylic acid through one step. The copolymers obtained through solution and bulk polymerization were insoluble in water and all organic solvents tried. Structural and compositional characterizations of hyperbranched PAcHP were performed by using FTIR, solid 13C-NMR, TGA, and titrimetric analysis. Acrylate fraction of the hyperbranched PAcHP obtained via bulk polymerization was determined as 60–65% by comparing TGA curves of hyperbranched PAcHP and pure poly(3-hydroxy propionate (PHP. However, analytical titration of the same sample revealed that acrylic acid units were about 47.3%. The results obtained from TGA and analytical titration were used to evaluate the chemical structure of the copolymer. Hyperbranched PAcHP exhibited hydrogel properties. Swelling behavior of the copolymer was investigated at a wide pH range and ionic strength. The dynamic swelling profiles of hyperbranched PAcHP exhibited a fast swelling behavior in the first hour and achieved the equilibrium state within 12 h in PBS. Depending on the conditions, the copolymers exhibited swelling ratios up to 2100%. As the copolymer has easily biodegradable propionate and versatile functional acrylic acid units, it can be used as not only biodegradable material in medical applications but also raw material in personal care commodities.

  11. The electrospinning of the copolymer of styrene and butyl acrylate for its application as oil absorbent.

    Science.gov (United States)

    Xu, Naiku; Cao, Jipeng; Lu, Yuyao

    2016-01-01

    Electrospun polystyrene materials have been employed as oil absorbents, but they have visible drawbacks such as poor strength at low temperature and unreliable integrity because of brittleness and insufficient cohesive force among fibers. Butyl acrylate can polymerize into flexible chains, and its polymer can be used as elastomer and adhesive material. Thereby it is possible to obtain the material that has better performance in comparison with electrospun polystyrene material through the electrospinning of the copolymer of styrene and butyl acrylate. In this work, a polymer was synthesized through suspension polymerization by using styrene and butyl acrylate as comonomers. The synthesis of the copolymer of styrene and butyl acrylate was verified through dissolution and hydrolysis experimental data; as well through nuclear magnetic resonance spectrometry. The viscous flow activation energy of the solution consisting of copolymer and N, N-dimethylformamide was determined via viscosity method and then adopted to establish the entanglement characteristics of butyl acrylate's chain segments. Finally, in order to electrospin the copolymer solution into fibrous membrane, the effects of monomer feed ratio and spinning parameters were investigated. The prepared fibrous membrane was found to have a potential use as oil absorbent.

  12. Temperature dependence of the heterogeneous uptake of acrylic acid on Arizona test dust.

    Science.gov (United States)

    Liu, Qifan; Wang, Yidan; Wu, Lingyan; Jing, Bo; Tong, Shengrui; Wang, Weigang; Ge, Maofa

    2017-03-01

    In this study, the temperature dependence of the heterogeneous uptake of acrylic acid on Arizona test dust (ATD) has been investigated within a temperature range of 255-315K using a Knudsen cell reactor. Combined with diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) experiment, it was found that acrylic acid could adsorb on ATD via surface OH groups and convert to carboxylate on the particle surface. The kinetics study suggests that the initial true uptake coefficient (γt) of acrylic acid on ATD decreases from (4.02±0.12)×10(-5) to (1.73±0.05)×10(-5) with a temperature increase from 255 to 315K. According to the temperature dependence of uptake coefficients, the enthalpy (ΔHobs) and entropy (ΔSobs) of uptake processes were determined to be -(9.60±0.38) KJ/mol and -(121.55±1.33) J·K/mol, respectively. The activation energy for desorption (Edes) was calculated to be (14.57±0.60) KJ/mol. These results indicated that the heterogeneous uptake of acrylic acid on ATD surface was sensitive to temperature. The heterogeneous uptake on ATD could affect the concentration of acrylic acid in the atmosphere, especially at low temperature. Copyright © 2016. Published by Elsevier B.V.

  13. Environmental Impacts on the Strength Parameters of Mineral-Acrylic (PMMA/ATH Facade Panels

    Directory of Open Access Journals (Sweden)

    Aleksander Byrdy

    2015-01-01

    Full Text Available Composite mineral-acrylic panels consist in 80% of natural minerals produced from bauxite (aluminium hydroxides (ATH and in 20% from acrylic resin (polymethyl methacrylate (PMMA. This material due to high usability is widely used in interior finishes. Recently, the mineral-acrylic panels have been used as external claddings of buildings. So far, there are several dozen elevations realized worldwide. Due to the variability of the strength parameters of PMMA acrylic resins depending on the environmental influence, a number of tests on samples of mineral-acrylic panels to verify their suitability for use in climate conditions in Central Europe were performed. The studies determined the change of the material parameters after being subjected to aging process in conditions of high temperature, high relative humidity, freeze-thaw cycles, and UV radiation. In the studies parameters such as flexural strength and modulus of elasticity were measured at a reference temperature of 23°C. In raised and lowered temperatures only the tensile strength tests were conducted. Due to the lack of information in the available literature, the authors carried out tests of the temperature influence on the PMMA/ATH composite modulus of elasticity and flexural strength which is crucial in designing process.

  14. Effect of autoclave postpolymerization treatments on the fracture toughness of autopolymerizing dental acrylic resins.

    Science.gov (United States)

    Durkan, Rukiye; Gürbüz, Ayhan; Yilmaz, Burak; Özel, M Birol; Bağış, Bora

    2012-06-26

    Microwave and water bath postpolymerization have been suggested as methods to improve the mechanical properties of heat and autopolymerizing acrylic resins. However, the effects of autoclave heating on the fracture properties of autopolymerizing acrylic resins have not been investigated. The aim of this study was to assess the effectiveness of various autoclave postpolymerization methods on the fracture properties of 3 different autopolymerizing acrylic resins. Forty-two specimens of 3 different autopolymerizing acrylic resins (Orthocryl, Paladent RR and Futurajet) were fabricated (40x8x4mm), and each group was further divided into 6 subgroups (n=7). Control group specimens remained as processed (Group 1). The first test group was postpolymerized in a cassette autoclave at 135°C for 6 minutes and the other groups were postpolymerized in a conventional autoclave at 130°C using different time settings (5, 10, 20 or 30 minutes). Fracture toughness was then measured with a three-point bending test. Data were analyzed by ANOVA followed by the Duncan test (α=0.05). The fracture toughness of Orthocryl and Paladent-RR acrylic resins significantly increased following conventional autoclave postpolymerization at 130°C for 10 minutes (Presins.

  15. Ultraviolet curing of acrylated liquid natural rubber for surface coating application

    Directory of Open Access Journals (Sweden)

    Kannikar Kwanming

    2009-01-01

    Full Text Available Ultraviolet curable acrylated liquid natural rubber was prepared by grafting of photosensitive molecule onto liquid natural rubber for surface coating application. The liquid natural rubber (LNR was firstly obtained by degradation of natural rubber latex with hydrogen peroxide and cobalt acetylacetonate at 65oC for 72 hrs. The preparation of acrylated natural rubber was carried out by the reaction of acrylic acid and epoxidized liquid natural rubber (ELNR prior obtained from LNR with formic acid and hydrogen peroxide in the ratio of 2:1 by weight in toluene at 80oC for 6, 9, 12, 18, and 24 hrs. It was found that the percentage of acrylate grafted onto liquid natural rubber depended on the reaction time. Surface coating was performed by using acrylated liquid natural rubber and 1,6-hexanediol diacrylate (HDDA or tripropylene glycol diacrylate (TPGDA as a crosslinker and Irgarcure 184 or Irgarcure 651 as a photoinitiator under UV exposure for 30, 60, and 90 seconds. The hardness test of cured products was investigated using the Pencil hardness test at pencil level of 2B to 6H. It was found that the highest hardness of surface coating was at pencil level of 4H for the product using TPGDA and Irgacure 651 in the ratio of 80:10 parts per hundred of rubber (phr. The cured products were able to resist to 2% H2SO4 and distilled water for more than 24 hrs.

  16. In Vitro Antifungal Evaluation of Seven Different Disinfectants on Acrylic Resins

    Directory of Open Access Journals (Sweden)

    A. Z. Yildirim-Bicer

    2014-01-01

    Full Text Available Objective. The aim of this study was to evaluate alternative methods for the disinfection of denture-based materials. Material and Methods. Two different denture-based materials were included in the study. Before microbial test, the surface roughness of the acrylic resins was evaluated. Then, the specimens were divided into 8 experimental groups (n=10, according to microorganism considered and disinfection methods used. The specimens were contaminated in vitro by standardized suspensions of Candida albicans ATCC#90028 and Candida albicans oral isolate. The following test agents were tested: sodium hypochlorite (NaOCl 1%, microwave (MW energy, ultraviolet (UV light, mouthwash containing propolis (MCP, Corega Tabs, 50% and 100% white vinegar. After the disinfection procedure, the number of remaining microbial cells was evaluated in CFU/mL. Kruskal-Wallis, ANOVA, and Dunn’s test were used for multiple comparisons. Mann Whitney U test was used to compare the surface roughness. Results. Statistically significant difference (P<0.05 was found between autopolymerised and heat-cured acrylic resins. The autopolymerised acrylic resin surfaces were rougher than surfaces of heat-cured acrylic resin. The most effective disinfection method was 100% white vinegar for tested microorganisms and both acrylic resins. Conclusion. This study showed that white vinegar 100% was the most effective method for tested microorganisms. This agent is cost-effective and easy to access and thus may be appropriate for household use.

  17. In vitro antifungal evaluation of seven different disinfectants on acrylic resins.

    Science.gov (United States)

    Yildirim-Bicer, A Z; Peker, I; Akca, G; Celik, I

    2014-01-01

    The aim of this study was to evaluate alternative methods for the disinfection of denture-based materials. Two different denture-based materials were included in the study. Before microbial test, the surface roughness of the acrylic resins was evaluated. Then, the specimens were divided into 8 experimental groups (n = 10), according to microorganism considered and disinfection methods used. The specimens were contaminated in vitro by standardized suspensions of Candida albicans ATCC#90028 and Candida albicans oral isolate. The following test agents were tested: sodium hypochlorite (NaOCl 1%), microwave (MW) energy, ultraviolet (UV) light, mouthwash containing propolis (MCP), Corega Tabs, 50% and 100% white vinegar. After the disinfection procedure, the number of remaining microbial cells was evaluated in CFU/mL. Kruskal-Wallis, ANOVA, and Dunn's test were used for multiple comparisons. Mann Whitney U test was used to compare the surface roughness. Statistically significant difference (P acrylic resins. The autopolymerised acrylic resin surfaces were rougher than surfaces of heat-cured acrylic resin. The most effective disinfection method was 100% white vinegar for tested microorganisms and both acrylic resins. This study showed that white vinegar 100% was the most effective method for tested microorganisms. This agent is cost-effective and easy to access and thus may be appropriate for household use.

  18. The Effect of Storage Environment on Dimensional Changes of Acrylic Resin Post Patterns

    Directory of Open Access Journals (Sweden)

    Abbas Fallahtafti

    2018-03-01

    Full Text Available Introduction: The purpose of this study was to compare dimensional changes of two types of auto polymerizing acrylic resin patterns (APARPs in three different storing environments. Methods: 60 acrylic post and core patterns were made of two types of Duralay acrylic resins (Aria dent, Iran and Reliance, Dental Mfg. Co, USA using a canine model. Then coronal, apical diameter and coronoapical length of patterns were measured. Afterwards, they were divided into two categories of 30 for each type of Duralay acrylic resin type. Each category was divided into three groups of ten randomly to immerse in three storage environments (Deconex®53plus Borer ChemieAG, Switzerland, Unident ® Impre(USF Healthcare S.A, Sweitzerland and water. After one hour, three mentioned values were measured again. Data were analyzed by SPSS20 using t-test, paired t-test and ANOVA. Results: Results showed that there were no statistically difference (p value> 0.05 about all dimensions of auto polymerizing acrylic post and core patterns except apical diameter and coronoapical length of Dental Mfg. Co, USA in Deconex®53 plus. Conclusion: The best environment to store Duralay APARPs with minimal changes was water and for disinfection, Deconex®53plus and Unident ® Imprecan showed acceptable properties with both of Duralay types.

  19. Efficacy of antimicrobial photodynamic therapy in the disinfection of acrylic denture surfaces: A systematic review.

    Science.gov (United States)

    Varela Kellesarian, Sergio; Abduljabbar, Tariq; Vohra, Fahim; Malmstrom, Hans; Yunker, Michael; Varela Kellesarian, Tammy; Romanos, Georgios E; Javed, Fawad

    2017-03-01

    The aim of the present systematic review was to assess the efficacy of antimicrobial photodynamic therapy (aPDT) in the disinfection of acrylic denture surfaces. IN order to address the focused question: "Is aPDT more effective in decontaminating denture surfaces compared with traditional denture-disinfection techniques?" an electronic search without time or language restrictions was conducted up to November 2016 in indexed databases using different key words. The exclusion criteria included qualitative and/or quantitative reviews, case reports, case series, commentaries, letters to the editor, interviews, and updates. A total of 14 studies were included and processed for data extraction, out of which 1 study was a randomized clinical trial and 13 studies were performed in vitro. Results from 12 experimental studies reported that aPDT was effective in reducing bacteria and/or yeast cultured in single or multispecies biofilm growth on acrylic resin specimens. One experimental study reported selective microorganism reduction on acrylic resin after aPDT. One clinical randomized control trial reported that aPDT presented similar microorganism reduction compared with oral antifungal medication for the disinfection of denture surfaces. The role of aPDT in the disinfection of acrylic resin surfaces is unclear. From a clinical perspective further randomized control trials are needed to assess the efficacy of aPDT in the disinfection of acrylic resin surfaces. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Cast Partial Denture versus Acrylic Partial Denture for Replacement of Missing Teeth in Partially Edentulous Patients

    Directory of Open Access Journals (Sweden)

    Pramita Suwal

    2017-03-01

    Full Text Available Aim: To compare the effects of cast partial denture with conventional all acrylic denture in respect to retention, stability, masticatory efficiency, comfort and periodontal health of abutments. Methods: 50 adult partially edentulous patient seeking for replacement of missing teeth having Kennedy class I and II arches with or without modification areas were selected for the study. Group-A was treated with cast partial denture and Group-B with acrylic partial denture. Data collected during follow-up visit of 3 months, 6 months, and 1 year by evaluating retention, stability, masticatory efficiency, comfort, periodontal health of abutment. Results: Chi-square test was applied to find out differences between the groups at 95% confidence interval where p = 0.05. One year comparison shows that cast partial denture maintained retention and stability better than acrylic partial denture (p< 0.05. The masticatory efficiency was significantly compromising from 3rd month to 1 year in all acrylic partial denture groups (p< 0.05. The comfort of patient with cast partial denture was maintained better during the observation period (p< 0.05. Periodontal health of abutment was gradually deteriorated in all acrylic denture group (p

  1. Histopathological evaluation of the effects of fiber reinforced acrylic resins on living tissues.

    Science.gov (United States)

    Özdemir, Ali Kemal; Polat, Nilüfer Tülin; Turgut, Mehmet; Özdemir Dogan, Derya; Göze, Fahrettin

    2013-01-01

    The aim of this study was the histopathological evaluation of the effects of the fiber reinforced acrylic resins on living tissues. The study was performed on 21 rabbits. Three groups, each including seven subjects, were formed. There was no applied plate in the control group. For the second group, heat-polymerized acrylic resin plates were inserted. For the third group, heat-polymerized acrylic resin plates containing proportionally 5% chopped silanated E type glass fiber were inserted. Plates were fixed to the palatine bone of the rabbits with titanium screws. Before the implementation of the plates and 1 month after the plates were applied, soft tissue samples were taken from the buccal mucosa of the rabbits. Also, tissue samples were taken from the control group. All samples were evaluated histopathologically. In the control group, only a focal atrophy was observed. In the acrylic group, large decomposition containing erythrocytes under the parahyperkeratotic region and micro-vesicle like spongiotic tissue reactions were observed. In the fiber reinforced acrylic group, widespread focal atrophy, bulgy look of the epithelium cells similar to apoptosis, over-distension and sub-corneal decomposition had been observed. In terms of atrophy and hyperkeratosis there were no statistically significant differences among groups. However, in respect to sub-corneal decomposition, there was a statistically significant difference in the fiber reinforced group (p decomposition of the fiber reinforced group had made us think that fiber edges had a traumatic effect on the reaction.

  2. MODIS Collection 6 Clear Sky Restoral (CSR): Filtering Cloud Mast 'Not Clear' Pixels

    Science.gov (United States)

    Meyer, Kerry G.; Platnick, Steven Edward; Wind, Galina; Riedi, Jerome

    2014-01-01

    Correctly identifying cloudy pixels appropriate for the MOD06 cloud optical and microphysical property retrievals is accomplished in large part using results from the MOD35 1km cloud mask tests (note there are also two 250m subpixel cloud mask tests that can convert the 1km cloudy designations to clear sky). However, because MOD35 is by design clear sky conservative (i.e., it identifies "not clear" pixels), certain situations exist in which pixels identified by MOD35 as "cloudy" are nevertheless likely to be poor retrieval candidates. For instance, near the edge of clouds or within broken cloud fields, a given 1km MODIS field of view (FOV) may in fact only be partially cloudy. This can be problematic for the MOD06 retrievals because in these cases the assumptions of a completely overcast homogenous cloudy FOV and 1-dimensional plane-parallel radiative transfer no longer hold, and subsequent retrievals will be of low confidence. Furthermore, some pixels may be identified by MOD35 as "cloudy" for reasons other than the presence of clouds, such as scenes with thick smoke or lofted dust, and should therefore not be retrieved as clouds. With such situations in mind, a Clear Sky Restoral (CSR) algorithm was introduced in C5 that attempts to identify pixels expected to be poor retrieval candidates. Table 1 provides SDS locations for CSR and partly cloudy (PCL) pixels.

  3. Characterization of avalanche photodiode arrays for the ClearPEM and ClearPEM-Sonic scanners

    Science.gov (United States)

    Bugalho, R.; Carriço, B.; Ferreira, C. S.; Frade, M.; Ferreira, M.; Moura, R.; Neves, J.; Ortigão, C.; Pinheiro, J. F.; Rodrigues, P.; Rolo, I.; Silva, J. C.; Silva, R.; Trindade, A.; Varela, J.

    2009-09-01

    The ClearPEM scanner is a high-resolution Positron Emission Mammography prototype, developed by the Portuguese PET Consortium in the framework of the Crystal Clear Collaboration at the European Organization for Nuclear Research (CERN). The scanner is based on a novel readout scheme which uses fine-pitch scintillator crystals, avalanche photodiodes, low-noise high-gain integrated electronics and a fast reconfigurable digital data acquisition system. The scanner uses two planar detector heads each composed of 96 detector modules. The detector module is composed of a matrix of 32 identical 2 × 2 × 20 mm3 LYSO:Ce scintillator crystals, coupled at both ends to Hamamatsu S8550 APD arrays for Depth-of-Interaction (DOI) measurements. More recently, a new scanner named ClearPEM-Sonic which combines the ClearPEM technology with an Ultrasound apparatus, is being produced. A set of 984 APD arrays used in both scanner assemblies followed a quality control protocol and a characterization procedure. This paper describes the methods used in these measurements and the results obtained with the full APD production batch.

  4. Evaluation of Liquid-Liquid Extraction Process for Separating Acrylic Acid Produced From Renewable Sugars

    Science.gov (United States)

    Alvarez, M. E. T.; Moraes, E. B.; Machado, A. B.; Maciel Filho, R.; Wolf-Maciel, M. R.

    In this article, the separation and the purification of the acrylic acid produced from renewable sugars were studied using the liquid-liquid extraction process. Nonrandom two-liquids and universal quasi-chemical models and the prediction method univeral quasi-chemical functional activity coefficients were used for generating liquid-liquid equilibrium diagrams for systems made up of acrylic acid, water, and solvents (diisopropyl ether, isopropyl acetate, 2-ethyl hexanol, and methyl isobutyl ketone) and the results were compared with available liquid-liquid equilibrium experimental data. Aspen Plus (Aspen Technology, Inc., version 2004.1) software was used for equilibrium and process calculations. High concentration of acrylic acid was obtained in this article using diisopropyl ether as solvent.

  5. Atypical pattern of (meth)acrylate allergic contact dermatitis in dental professionals.

    Science.gov (United States)

    Prasad Hunasehally, R Y; Hughes, T M; Stone, N M

    2012-09-01

    (Meth)acrylates in dental bonding agents are a common source of allergic contact dermatitis in dental professionals. The distribution of the contact dermatitis is commonly on finger tips, but is determined by individual habits as demonstrated by the two case reports in this article. Despite the site of contact dermatitis, the bonding agents are often not suspected as a source of contact allergy due to misconception regarding the protective effect of natural rubber latex gloves. With these case reports, we endeavour to emphasize the inadequacy of the latex gloves in protecting against the (meth)acrylate induced contact allergy and also list the measures a dental professional needs to incorporate in order to minimise the risks of sensitisation to (meth)acrylates.

  6. Radiation synthesis of superabsorbent poly(acrylic acid)-carrageenan hydrogels

    Energy Technology Data Exchange (ETDEWEB)

    Francis, Sanju; Kumar, Manmohan; Varshney, Lalit E-mail: lalitv@magnum.barc.ernet.in

    2004-04-01

    A series of superabsorbent hydrogels were prepared from carrageenan and partially neutralized acrylic acid by gamma irradiation at room temperature. The gel fraction, swelling kinetics and the equilibrium degree of swelling (EDS) of the hydrogels were studied. It was found that the incorporation of even 1% carrageenan (sodium salt) increases the EDS of the hydrogels from {approx}320 to {approx}800 g/g. Thermal analysis were carried out to determine the amount of free water and bound water in the hydrogels. Under optimum conditions, poly(acrylic acid)-carrageenan hydrogels with high gel fraction ({approx}80%) and very high EDS ({approx}800 g/g) were prepared gamma radiolytically from aqueous solution containing 15% partially neutralized acrylic acid and 1-5% carrageenan. The hydrogels were also found to be sensitive to the pH and the ionic strength of the medium.

  7. Synthesis of radiation crosslinked poly(acrylic acid) in the presence of phenyltriethoxysilane

    Science.gov (United States)

    Hassan, Safia; Yasin, Tariq

    2014-04-01

    Acrylic acid based superabsorbent hydrogel was prepared using phenyltriethoxysilane (PTES) as polyfunctional monomer. Different amounts of PTES were incorporated in acrylic acid and irradiated at different doses upto maximum of 30 kGy. The crosslinked acrylic acid showed hydrogel properties and its swelling kinetics, gel fraction and equilibrium degree of swelling (EDS) were studied. It was found that the increased PTES concentration decreased the EDS of the hydrogels. Infrared spectroscopy confirmed the crosslinking reaction between the feed components and the existence of siloxane bond. Thermogravimetric analysis showed an increase in the stability of the hydrogels having high PTES content. The swelling of the hydrogel was affected by pH, ionic strength and temperature. These hydrogels showed low swelling in acidic and basic pH range and high swelling around neutral pH. This switchable pH response of these hydrogels can be exploited in environmental and biomedical applications.

  8. Nitrile Hydratase and Amidase from Rhodococcus rhodochrous Hydrolyze Acrylic Fibers and Granular Polyacrylonitriles

    Science.gov (United States)

    Tauber, M. M.; Cavaco-Paulo, A.; Robra, K.-H.; Gübitz, G. M.

    2000-01-01

    Rhodococcus rhodochrous NCIMB 11216 produced nitrile hydratase (320 nkat mg of protein−1) and amidase activity (38.4 nkat mg of protein−1) when grown on a medium containing propionitrile. These enzymes were able to hydrolyze nitrile groups of both granular polyacrylonitriles (PAN) and acrylic fibers. Nitrile groups of PAN40 (molecular mass, 40 kDa) and PAN190 (molecular mass, 190 kDa) were converted into the corresponding carbonic acids to 1.8 and 1.0%, respectively. In contrast, surfacial nitrile groups of acrylic fibers were only converted to the corresponding amides. X-ray photoelectron spectroscopy analysis showed that 16% of the surfacial nitrile groups were hydrolyzed by the R. rhodochrous enzymes. Due to the enzymatic modification, the acrylic fibers became more hydrophilic and thus, adsorption of dyes was enhanced. This was indicated by a 15% increase in the staining level (K/S value) for C.I. Basic Blue 9. PMID:10742253

  9. Radiation Induced Grafting of Acrylate onto Waste Rubber: The Effect of Monomer Type

    Directory of Open Access Journals (Sweden)

    Shirajuddin Siti Salwa M.

    2017-01-01

    Full Text Available The effect of three different acrylate group monomers, namely n-butyl acrylate, methacrylic acid and tripropylene glycol diacrylate of radiation induced grafting onto waste rubber was studied. The electron beam accelerator operated at voltage of 2MeV was used to irradiate the waste rubber at 10 kGy and 100 kGy absorbed radiation dose, respectively. The formation of grafting was observed from the increase in the grafting yield and confirmed by Transformed Infra-Red Spectroscopy results. According to the result obtained, only tripropylene glycol diacrylate was selected to graft onto waste rubber. The carbonyl bond from acrylate groups was seen at 1726 cm-1 band which confirmed the presence of TPGDA in the polymer matrix. This indicates the successful preparation of the TPGDA-grafted waste rubber via radiation induced grafting techniques.

  10. Hybrid thiol-ene network nanocomposites based on multi(meth)acrylate POSS.

    Science.gov (United States)

    Li, Liguo; Liang, Rendong; Li, Yajie; Liu, Hongzhi; Feng, Shengyu

    2013-09-15

    First, multi(meth)acrylate functionalized POSS monomers were synthesized in this paper. Secondly, FTIR was used to evaluate the homopolymerization behaviors of multi(meth)acrylate POSS and their copolymerization behaviors in the thiol-ene reactions with octa(3-mercaptopropyl) POSS in the presence of photoinitiator. Results showed that the photopolymerization rate of multimethacrylate POSS was faster than that of multiacrylate POSS. The FTIR results also showed that the copolymerizations were dominant in the thiol-ene reactions with octa(3-mercaptopropyl) POSS, different from traditional (meth)acrylate-thiol system, in which homopolymerizations were predominant. Finally, the resulted hybrid networks based on POSS were characterized by XRD, FE-SEM, DSC, and TGA. The characterization results showed that hybrid networks based on POSS were homogeneous and exhibited high thermal stability. Copyright © 2013 Elsevier Inc. All rights reserved.

  11. Pathogenesis of neurotoxicity of acrylates acrylonitrile and acrylamide: from cell to organism.

    Science.gov (United States)

    Tarskikh, M M; Klimatskaya, L G; Kolesnikov, S I

    2013-08-01

    The incubation of 10 mM acrylamide (in vitro) with rat brain homogenate was followed by a decrease in catalase activity by 48% as soon as 5 min after addition of acrylate to the incubation medium. Activity of this enzyme remained low 30 min after the start of the experiment. Acute poisoning with this acrylate was accompanied by LPO activation in rat brain 24 h after injection. Exposure to acrylonitrile during occupational contacts with this monomer was followed by accumulation of adducts of acrylate with erythrocytic hemoglobin in human blood. In accordance with previously observed data, modern scheme of neurotropic effects of acrylonitrile and acrylamide was proposed. This scheme explained specific features of clinical syndromes induced by acute and chronic exposure to these toxic agents.

  12. Do flexible acrylic resin lingual flanges improve retention of mandibular complete dentures?

    Science.gov (United States)

    Ahmed Elmorsy, Ayman Elmorsy; Ahmed Ibraheem, Eman Mostafa; Ela, Alaa Aboul; Fahmy, Ahmed; Nassani, Mohammad Zakaria

    2015-01-01

    Objectives: The aim of this study was to compare the retention of conventional mandibular complete dentures with that of mandibular complete dentures having lingual flanges constructed with flexible acrylic resin “Versacryl.” Materials and Methods: The study sample comprised 10 completely edentulous patients. Each patient received one maxillary complete denture and two mandibular complete dentures. One mandibular denture was made of conventional heat-cured acrylic resin and the other had its lingual flanges made of flexible acrylic resin Versacryl. Digital force-meter was used to measure retention of mandibular dentures at delivery and at 2 weeks and 45 days following denture insertion. Results: The statistical analysis showed that at baseline and follow-up appointments, retention of mandibular complete dentures with flexible lingual flanges was significantly greater than retention of conventional mandibular dentures (P dentures, retention of dentures increased significantly over the follow-up period (P dentures improved denture retention. PMID:26539387

  13. Clear New View of a Classic Spiral

    Science.gov (United States)

    2010-05-01

    ESO is releasing a beautiful image of the nearby galaxy Messier 83 taken by the HAWK-I instrument on ESO's Very Large Telescope (VLT) at the Paranal Observatory in Chile. The picture shows the galaxy in infrared light and demonstrates the impressive power of the camera to create one of the sharpest and most detailed pictures of Messier 83 ever taken from the ground. The galaxy Messier 83 (eso0825) is located about 15 million light-years away in the constellation of Hydra (the Sea Serpent). It spans over 40 000 light-years, only 40 percent the size of the Milky Way, but in many ways is quite similar to our home galaxy, both in its spiral shape and the presence of a bar of stars across its centre. Messier 83 is famous among astronomers for its many supernovae: vast explosions that end the lives of some stars. Over the last century, six supernovae have been observed in Messier 83 - a record number that is matched by only one other galaxy. Even without supernovae, Messier 83 is one of the brightest nearby galaxies, visible using just binoculars. Messier 83 has been observed in the infrared part of the spectrum using HAWK-I [1], a powerful camera on ESO's Very Large Telescope (VLT). When viewed in infrared light most of the obscuring dust that hides much of Messier 83 becomes transparent. The brightly lit gas around hot young stars in the spiral arms is also less prominent in infrared pictures. As a result much more of the structure of the galaxy and the vast hordes of its constituent stars can be seen. This clear view is important for astronomers looking for clusters of young stars, especially those hidden in dusty regions of the galaxy. Studying such star clusters was one of the main scientific goals of these observations [2]. When compared to earlier images, the acute vision of HAWK-I reveals far more stars within the galaxy. The combination of the huge mirror of the VLT, the large field of view and great sensitivity of the camera, and the superb observing conditions

  14. A pH-, salt- and solvent-responsive carboxymethylcellulose-g-poly(sodium acrylate/medical stone superabsorbent composite with enhanced swelling and responsive properties

    Directory of Open Access Journals (Sweden)

    2011-05-01

    Full Text Available Free-radical graft copolymerization among sodium carboxymethylcellulose (CMC, partially neutralized acrylic acid (NaA, medical stone (MS and crosslinker N,N'-methylene-bis-acrylamide (MBA was performed to prepare new carboxymethylcellulose-g-poly(sodium acrylate/medical stone (CMC-g-PNaA/MS superabsorbent composites. Fourier transform infrared (FTIR spectra, thermogravimetry- differential scanning calorimetry (TG-DSC and field emission scanning electromicrsocopic (FESEM analysis confirmed that NaA had been grafted onto CMC backbone and MS participated in polymerization, and the thermal stability and surface morphologies were improved by the addition of MS. Energy dispersive spectrometer (EDS and elemental map (EM analyses revealed the better distribution of MS in the CMC-g-PNaA matrix. The incorporation of 20 wt% MS clearly enhanced the water absorption by 100% (from 317 to 634 g/g. The developed composites showed enhanced swelling rate and On-Off switching swelling characteristics in various pH solutions, saline solutions and hydrophilic organic solvents, which represented interesting and reversible pH-, saline- and hydrophilic organic solvent-responsive characteristics. In addition, the composite exhibited intriguing time-dependent kinetic swelling properties in various heavy metal solutions.

  15. Comparison of acrylic and polymethyl methacrylate lenses in a pediatric population

    Directory of Open Access Journals (Sweden)

    Aasuri Murali

    2006-01-01

    Full Text Available Purpose: To compare the intra-patient incidence of posterior capsular opacification (PCO and their post operative course, in children with bilateral cataract, following implantation of acrylic (Group 1 and polymethyl methacrylate (PMMA (Group 2 intraocular lenses (IOLs. Materials and Methods: This was a prospective, interventional intra-patient case series. Twenty-five children with bilateral cataract, 5 years and older, underwent cataract surgery and implantation of an acrylic (AcrySof MA30BA, Alcon, Fortworth, TX in one eye and PMMA (Indo Am IAB 203, Ocular Vision, Inc. IOL in the other eye of each patient. They were followed up for an average of 11.1 ± 9.5 months to assess the incidence of clinically significant PCO and occurrence of postoperative complications. Results: Twenty-three children (46 eyes, were included in this study. Post-operatively, 22(95.6% patients with acrylic IOLs and 20 (86.9% patients with PMMA IOLs, either maintained or improved their vision. In the acrylic and PMMA IOL groups respectively, the incidence of clinically significant PCO was 21% (4 and 75% (12 ( P =0.002, with a median onset at 2.9 months and 0.7 months. Other complications included pupillary capture in 2 (8.7% eyes and uveal prolapse in 1 (4.3% eye in the acrylic group and increased uveal inflammation in 6 (26.1% eyes and presumed noninfectious endophthalmitis in 2 (8.7% eyes in the PMMA group. Conclusion: Incidence of PCO and post operative uveal inflammation is significantly less with acrylic lenses and were safe to use in pediatric eyes.

  16. Comparison of acrylic and polymethyl methacrylate lenses in a pediatric population.

    Science.gov (United States)

    Aasuri, Murali K; Fernandes, Merle; Pathan, Padmaja Preetam

    2006-06-01

    To compare the intra-patient incidence of posterior capsular opacification (PCO) and their post operative course, in children with bilateral cataract, following implantation of acrylic (Group 1) and polymethyl methacrylate (PMMA) (Group 2) intraocular lenses (IOLs). This was a prospective, interventional intra-patient case series. Twenty-five children with bilateral cataract, 5 years and older, underwent cataract surgery and implantation of an acrylic (AcrySof MA30BA, Alcon, Fortworth, TX) in one eye and PMMA (Indo Am IAB 203, Ocular Vision, Inc.) IOL in the other eye of each patient. They were followed up for an average of 11.1 +/- 9.5 months to assess the incidence of clinically significant PCO and occurrence of postoperative complications. Twenty-three children (46 eyes), were included in this study. Post-operatively, 22(95.6%) patients with acrylic IOLs and 20 (86.9%) patients with PMMA IOLs, either maintained or improved their vision. In the acrylic and PMMA IOL groups respectively, the incidence of clinically significant PCO was 21% (4) and 75% (12) ( P =0.002), with a median onset at 2.9 months and 0.7 months. Other complications included pupillary capture in 2 (8.7%) eyes and uveal prolapse in 1 (4.3%) eye in the acrylic group and increased uveal inflammation in 6 (26.1%) eyes and presumed noninfectious endophthalmitis in 2 (8.7%) eyes in the PMMA group. Incidence of PCO and post operative uveal inflammation is significantly less with acrylic lenses and were safe to use in pediatric eyes.

  17. High-impact strength acrylic denture base material processed by autoclave.

    Science.gov (United States)

    Abdulwahhab, Salwan Sami

    2013-10-01

    To investigate the effect of two different cycles of autoclave processing on the transverse strength, impact strength, surface hardness and the porosity of high-impact strength acrylic denture base material. High Impact Acryl was the heat-cured acrylic denture base material included in the study. A total of 120 specimens were prepared, the specimens were grouped into: control groups in which high-impact strength acrylic resins processed by conventional water-bath processing technique (74°C for 1.5 h then boil for 30 min) and experimental groups in which high-impact strength acrylic resins processed by autoclave at 121°C, 210 kPa .The experimental groups were divided into (fast) groups for 15 min, and (slow) groups for 30 min. To study the effect of the autoclave processing (Tuttnauer 2540EA), four tests were conducted transverse strength (Instron universal testing machine), impact strength (Charpy tester), surface hardness (shore D), and porosity test. The results were analyzed to ANOVA and LSD test. In ANOVA test, there were highly significant differences between the results of the processing techniques in transverse, impact, hardness, and porosity test. The LSD test showed a significant difference between control and fast groups in transverse and hardness tests and a non-significant difference in impact test and a highly significant difference in porosity test; while, there were a highly significant differences between control and slow groups in all examined tests; finally, there were a non-significant difference between fast and slow groups in transverse and porosity tests and a highly significant difference in impact and hardness tests. In the autoclave processing technique, the slow (long) curing cycle improved the tested physical and mechanical properties as compared with the fast (short) curing cycle. The autoclave processing technique improved the tested physical and mechanical properties of High Impact Acryl. Copyright © 2013 Japan Prosthodontic Society

  18. Bonding of autopolymerizing acrylic resins to magnetic stainless steel alloys using metal conditioner.

    Science.gov (United States)

    Shimizu, Hiroshi; Tsue, Fumitake; Chen, Zhao-Xun; Kawaguchi, Tomohiro; Takahashi, Yutaka

    2008-02-01

    The shear bond strengths of a barbituric acid derivative-activated autopolymerizing acrylic resin to two magnetic stainless steel alloys using a metal conditioner were investigated. The surfaces of the two magnetic stainless steel alloys were abraded with 600-grit silicon carbide paper. The surface preparations were: Group 1 (without preparation), Group 2 (airborne particle abrasion with 50 microm alumina), and Group 3 (airborne particle abrasion followed by priming with a metal conditioner). The alloys were bonded with a barbituric acid derivative-activated autopolymerizing acrylic resin. For comparison, airborne particle abrasion and bonding with a tri-n-butylborane-initiated autopolymerizing acrylic resin (Group 4), as well as airborne particle abrasion followed by priming with a metal conditioner and bonding with the same resin (Group 5) were added. Half of the specimens were thermocycled up to 10,000 cycles. The shear bond strengths were determined. Group 3 had significantly improved shear bond strengths with the barbituric acid derivative-activated autopolymerizing acrylic resin to both stainless steel alloys. Although there were no significant differences in the bond strength among Groups 3-5 before thermocycling, the decrease in the bond strength of Group 3 was considerably greater than that of Groups 4 or 5 after thermocycling for both stainless steel alloys. Significant improvements in the bond strength of the barbituric acid derivative-activated autopolymerizing acrylic resin to two magnetic stainless steel alloys were achieved by airborne particle abrasion followed by priming with the metal conditioner. The bond durability to this resin, however, was inferior to that to a tri-n-butylborane-initiated autopolymerizing acrylic resin.

  19. Electroactive behavior assessment of poly(acrylic acid)-graphene oxide composite hydrogel in the detection of cadmium

    NARCIS (Netherlands)

    Bejarano-Jimenez, A.; Escobar-Barrios, V.A.; Kleijn, J.M.; Oritz-Ledon, C.A.; Chazaro-Ruiz, L.F.

    2014-01-01

    Super absorbent polymers of acrylic acid-graphene oxide (PAA-GO) were synthesized with different percentage of chemical neutralization (0, 10, and 20%) of the acrylic acid monomer before its polymerization. The influence of their swelling and adsorption/desorption capacity of cadmium ions in aqueous

  20. Real-time monitoring of the penetration of amphiphilic acrylate copolymer in leather using a fluorescent copolymer as tracer.

    Science.gov (United States)

    Du, Jin-Xia; Shi, Lu; Peng, Bi-Yu

    2015-12-01

    A fluorescent tracer, poly (acrylic-co-stearyl acrylate-co-3-acryloyl fluorescein) [poly (AA-co-SA-co-Ac-Flu)], used for real-time monitoring the penetration of amphiphilic acrylate copolymer, poly (acrylic-co-stearyl acrylate) [poly (AA-co-SA)], in leather was synthesized by radical polymerization of acrylic, stearyl acrylate and fluorescent monomer, 3-acryloyl fluorescein (Ac-Flu). The structure, molecular weight, introduced fluorescent group content and fluorescent characteristics of the fluorescent tracer and target copolymer, amphiphilic acrylate copolymer, were also characterized. The results show that the tracer presents the similar structural characteristics to the target and enough fluorescence intensity with 1.68 wt % of the fluorescent monomer introduced amount. The vertical section of the leather treated with the target copolymer mixing with 7% of the tracer exhibits evident fluorescence, and the change of fluorescence intensity along with the vertical section with treating time increasing can reflect the penetration depth of the target copolymer. The introduction of the fluorescent group in polymer structure through copolymerization with a limited amount of fluorescent monomer, Ac-Flu, is an effective way to make a tracer to monitor the penetration of the target in leather, which provides a new thought for the penetration research of syntans such as vinyl copolymer materials in leather manufacture. © 2015 Wiley Periodicals, Inc.

  1. Adherence of Candida albicans to denture base acrylics and silicone-based resilient liner materials with different surface finishes

    NARCIS (Netherlands)

    Nevzatoglu, Erdem U.; Ozcan, Mutlu; Kulak-Ozkan, Yasemin; Kadir, Tanju

    This study evaluated the surface roughness and Candida albicans adherence on denture base acrylic resins and silicone-based resilient liners with different surface finishes. Four commercial denture base acrylic resins ( three heat polymerized and one room temperature polymerized) and five

  2. Synthesis of dense poly(acrylic acid) brushes and their interaction with amine-functional silsesquioxane nanoparticles

    NARCIS (Netherlands)

    Retsch, Markus; Walther, Andreas; Loos, Katja; Mueller, Axel H. E.; Müller, Axel H.E.

    2008-01-01

    Poly(acrylic acid) polyetectrolyte brushes were synthesized by surface-initiated atom transfer radical polymerization (SI-ATRP) of tert-butyl acrylate on planar gold surfaces and subsequent hydrolysis. Three types of monolayers with different numbers of thiol binding sites per initiating unit were

  3. Designing ultraviolet curing of multifunctional (meth)acrylate hard coats

    Science.gov (United States)

    Wen, Mei

    Ultraviolet (UV) curing rapidly converts multifunctional (meth)acrylate liquid monomers into highly cross-linked, impervious, hard polymeric coatings at ambient temperature. This solidification process occurs by free-radical cross-linking polymerization. To achieve a better design of this process, it is desirable to have high conversion of functional groups, low stress, adequate mechanical properties, and low costs. To approach this design goal, the following modeling and experimental work was carried out. Firstly, a kinetic model was developed to simulate radical trapping. This model predicts a peak in the concentration of active radicals and a monotonic rise of the concentration of trapped radicals during polymerization. It also predicts a decrease in the fraction of trapped radicals at a given conversion as the UV light intensity is raised. Secondly, a kinetic gelation model, in which reaction occurs locally on a lattice, was developed. Unlike previous such models, this model accounts for free radical reaction time more accurately. It was found that a more uniform distribution of reacted sites leads to a favored propagation at a given conversion. Moreover, radical trapping and termination were found to shorten the kinetic chain length and to lower the asymptotic conversion reached when initiators are exhausted. Thirdly, elastic modulus evolution was simulated with a rigidity percolation model, in which bonds created by free-radical polymerization are represented as rigidly jointed beams. Simulations show that modulus of a network depends on the connectivity between monomer units as well as bonding structure. Finally, experimental determination of volume shrinkage of a sandwiched film was measured with a dynamic mechanical analyzer probe. A faster reaction causes more severely delayed volume shrinkage from the thermodynamic equilibrium volume required by the reaction. Nevertheless, volume shrinks more when the shrinkage of the thermodynamic volume rises. In

  4. Wearable health device dermatitis: a case of acrylate-related contact allergy.

    Science.gov (United States)

    Winston, Flaura K; Yan, Albert C

    2017-08-01

    The popularity of mobile wearable health devices has skyrocketed. Some of these devices are worn on the wrist and have been associated with the development of allergic contact dermatitis. Although nickel has been the suspected culprit in cases reported by the media for consumers, we present a rare report of a patient who developed a localized contact dermatitis that was linked to acrylate allergy on epicutaneous patch testing. We surmise that the source of this acrylate might derive from leaching of this compound from the rechargeable battery housing given its correspondence to where the rash arose.

  5. Catalytic Cracking of Lactide and Poly(Lactic Acid) to Acrylic Acid at Low Temperatures.

    Science.gov (United States)

    Terrade, Frédéric G; van Krieken, Jan; Verkuijl, Bastiaan J V; Bouwman, Elisabeth

    2017-05-09

    Despite being a simple dehydration reaction, the industrially relevant conversion of lactic acid to acrylic acid is particularly challenging. For the first time, the catalytic cracking of lactide and poly(lactic acid) to acrylic acid under mild conditions is reported with up to 58 % yield. This transformation is catalyzed by strong acids in the presence of bromide or chloride salts and proceeds through simple SN 2 and elimination reactions. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  6. Antibacterial activity of chitosan and the interpolyelectrolyte complexes of poly(acrylic acid)-chitosan

    OpenAIRE

    Hortensia Ortega-Ortiz; Baltazar Gutiérrez-Rodríguez; Gregorio Cadenas-Pliego; Luis Ibarra Jimenez

    2010-01-01

    The antimicrobial activity of chitosan and water soluble interpolyelectrolyte complexes of poly(acrylic acid)-chitosan was studied. Chitosans of two different molecular weights were tested at different concentration for 0.5 to 5 g·L-1 as antimicrobial agents against P. aeruginosa and P. oleovorans. In both cases, the best microbial inhibition was obtained with the concentration of 5 g·L-1. However, the interpolyelectrolyte complexes of poly(acrylic acid)-chitosan with composition φ =2 pr...

  7. Chemical Fixation of CO{sub 2} to Acrylates Using Low-Valent Molybdenum Sources

    Energy Technology Data Exchange (ETDEWEB)

    Bernskoetter, Wesley

    2013-09-30

    The kinetic, mechanistic, and reactivity experiments to access the viability and possible reaction design of coupling of carbon dioxide and ethylene at a zerovalent molybdenum for the production of acrylates are described. A general model of the reaction mechanism has been outlined, including assessment of the rate limiting step in the reaction. Kinetic and computational data have valuated the influence of a range of tridentate ligand platforms on the rate of coupling. An in situ reduction and acrylate formation activity screen protocol has also been developed to aid in the technology development of this process. Portions of descriptions of the research products presented here have also been adapted with permission from journal publications.

  8. Self-Compacting Concrete Incorporating Micro-SiO2 and Acrylic Polymer

    Directory of Open Access Journals (Sweden)

    Ali Heidari

    2014-01-01

    Full Text Available This study examined the effects of using acrylic polymer and micro-SiO2 in self-compacting concrete (SCC. Using these materials in SCC improves the characteristics of the concrete. Self-compacting samples with 1-2% of a polymer and 10% micro-SiO2 were made. In all cases, compressive strength, water absorption, and self-compacting tests were done. The results show that adding acrylic polymer and micro-SiO2 does not have a significant negative effect on the mechanical properties of self-compacting concrete. In addition using these materials leads to improving them.

  9. Using acrylic resin tooth veneers in patients with an abnormal jaw relationship: a case report.

    Science.gov (United States)

    Yang, Tsung-Chieh; Lan, Yi-Hao; Wang, Tong-Mei; Tu, Ching-Yu; Lin, Li-Deh

    2014-01-01

    This case report describes and evaluates a method of arranging artificial teeth in patients with an abnormal jaw relationship in which a wider maxillary arch opposes a narrower mandibular arch. First, the fossa of mandibular posterior teeth was positioned on the crest of the mandibular edentulous ridge. The maxillary posterior teeth were then placed palatally to maximize occlusal contacts with the opposing mandibular teeth. Finally, acrylic resin tooth veneers were attached on the buccal surface of posterior maxillary teeth to improve the arch discrepancy. This method addresses functional considerations with the inner aspect of teeth and esthetic considerations with acrylic resin tooth veneers.

  10. [Acrylates as a significant source of occupational and non-occupational contact allergy].

    Science.gov (United States)

    Zaremba, Joanna; Kieć-Swierczyńska, Marta; Krecisz, Beata; Swierczyńska-Machura, Dominika

    2004-01-01

    The authors review the literature on the contact allergy to acrylate plastics used in many branches of industry, construction, dental prosthetics, conservative dentistry, orthopedics and also in the production of glue, binding materials, and lacquers, especially printer's ink. The most frequent sources of non-occupational allergy are presented. In addition, the authors draw attention to new allergy-producing chemical compounds, difficulties in the interpretation of skin test results, mostly because of polyvalence of allergy to acrylates, and to characteristic clinical picture of skin changes.

  11. Application of Functionalized SWCNTs for Increase of Degradation Resistance of Acrylic Paint for Cars

    Directory of Open Access Journals (Sweden)

    Osiel Lucas Flores

    2013-01-01

    Full Text Available Physical properties of automotive acrylic paint are improved by incorporation of three different types of carbon nanotubes: single-wall carbon nanotubes (SWCNTs, OH-functionalized single-wall carbon nanotubes (OH-SWCNTs, and aniline-functionalized single-wall carbon nanotubes (aniline-SWCNTs. The formed composites are studied by electron miscroscopy methods and Raman spectrometry. It is found that the acrylic paints with addition of OH-SWCNTs and aniline-SWCNTs show better quality for their applications. In particular, the resistance against degradation by electron beam increased in ~500%.

  12. Gold Nanoparticles Protected with Thiol-Derivatized Amphiphilic Poly(epsilon-caprolactone)-b-poly(acrylic acid)

    DEFF Research Database (Denmark)

    Javakhishvili, Irakli; Hvilsted, Søren

    2009-01-01

    Amphiphilic poly(epsilon-caprolactone)-b-poly(acrylic acid) (HS-PCL-b-PAA) with a thiol functionality in the PCL terminal has been prepared in a novel synthetic cascade. Initially, living anionic ring-opening polymerization (ROP) of epsilon-caprolactone (epsilon-CL) employing the difunctional......) of tent-butyl acrylate (tBA) in a controlled fashion by use of NiBr2(PPh3)(2) catalyst to produce Prot-PCL-b-PtBA with narrow polydispersities (1.17-1.39). Subsequent mild deprotection protocols provided HS-PCL-b-PAA. Reduction of a gold salt in the presence of this macroligand under thiol...

  13. Inhibiting electro-thermal breakdown of acrylic dielectric elastomer actuators by dielectric gel coating

    Science.gov (United States)

    La, Thanh-Giang; Lau, Gih-Keong

    2016-01-01

    Electrical breakdown of dielectric elastomer actuators (DEA) is very localized; a spark and a pinhole (puncture) in dielectric ends up with short-circuit. This letter shows that prevention of electrothermal breakdown helps defer failure of DEAs even with conductive-grease electrodes. Dielectric gel encapsulation or coating (Dow Corning 3-4170) helps protect acrylic elastomer (VHB 4905), making it thermally more stable and delaying its thermal oxidation (burn) from 218 °C to 300 °C. Dielectric-gel-coated acrylic DEAs can withstand higher local leak-induced heating and thus achieve higher dielectric strengths than non-coated DEAs do.

  14. 78 FR 50259 - Derivatives Clearing Organizations and International Standards

    Science.gov (United States)

    2013-08-16

    .... (``CME''), ICE Clear Credit LLC (``ICE Clear Credit''), and The Options Clearing Corporation (``OCC... is the Supervisory Agency only for CME and ICE Clear Credit, the SEC serves as OCC's Supervisory... and central banks from around the world including, Argentina, Australia, Belgium, Brazil, Canada...

  15. Facile preparation of mussel-inspired polyurethane hydrogel and its rapid curing behavior.

    Science.gov (United States)

    Sun, Peiyu; Wang, Jing; Yao, Xiong; Peng, Ying; Tu, Xiaoxiong; Du, Pengfei; Zheng, Zhen; Wang, Xinling

    2014-08-13

    A facile method was found to incorporate a mussel-inspired adhesive moiety into synthetic polymers, and mussel mimetic polyurethanes were developed as adhesive hydrogels. In these polymers, a urethane backbone was substituted for the polyamide chain of mussel adhesive proteins, and dopamine was appended to mimic the adhesive moiety of adhesive proteins. A series of mussel mimetic polyurethanes were created through a step-growth polymerization based on hexamethylene diisocyanate as a hard segment, PEG having different molecular weights as a soft segment, and lysine-dopamine as a chain extender. Upon a treatment with Fe(3+), the aqueous mussel mimetic polyurethane solutions can be triggered by pH adjustment to form adhesive hydrogels instantaneously; these materials can be used as injectable adhesive hydrogels. Upon a treatment with NaIO4, the mussel mimetic polyurethane solutions can be cured in a controllable period of time. The successful combination of the unique mussel-inspired adhesive moiety with a tunable polyurethane structure can result in a new kind of mussel-inspired adhesive polymers.

  16. Occupational allergic contact dermatitis from 2-hydroxyethyl methacrylate and ethylene glycol dimethacrylate in a modified acrylic structural adhesive.

    Science.gov (United States)

    Kanerva, L; Jolanki, R; Leino, T; Estlander, T

    1995-08-01

    Acrylates have a broad area of application in various products including glues, sealants and adhesives. Whereas anaerobic acrylic sealants are well-known sensitizers, acrylate glues that cure in air have only seldom been reported as allergens. Here a patient sensitized to such a glue, and developing hand dermatitis that spread to the lower arms, chest, neck and face, is presented. Her glue was analyzed by gas chromatography/mass spectrometry (GC/MS) and contained 24.6% 2-hydroxyethyl methacrylate (2-HEMA) and 0.4% ethylene glycol dimethacrylate (EGDMA). These 2 acrylate compounds, as well as her glue, provoked an allergic patch test reaction. Also many other acrylate compounds, e.g., tetrahydrofurfuryl methacrylate, gave an allergic reaction indicating cross-allergy. The patient could not continue in her previous workplace because of severely relapsing skin symptoms.

  17. Synthesis and Characterization of Waterborne Fluoropolymers Prepared by the One-Step Semi-Continuous Emulsion Polymerization of Chlorotrifluoroethylene, Vinyl Acetate, Butyl Acrylate, Veova 10 and Acrylic Acid

    Directory of Open Access Journals (Sweden)

    Hongzhu Liu

    2017-01-01

    Full Text Available Waterborne fluoropolymer emulsions were synthesized using the one-step semi-continuous seed emulsion polymerization of chlorotrifluoroethylene (CTFE, vinyl acetate (VAc, n-butyl acrylate (BA, Veova 10, and acrylic acid (AA. The main physical parameters of the polymer emulsions were tested and analyzed. Characteristics of the polymer films such as thermal stability, glass transition temperature, film-forming properties, and IR spectrum were studied. Meanwhile, the weatherability of fluoride coatings formulated by the waterborne fluoropolymer and other coatings were evaluated by the quick ultraviolet (QUV accelerated weathering test, and the results showed that the fluoropolymer with more than 12% fluoride content possessed outstanding weather resistance. Moreover, scale-up and industrial-scale experiments of waterborne fluoropolymer emulsions were also performed and investigated.

  18. Synthesis and Characterization of Waterborne Fluoropolymers Prepared by the One-Step Semi-Continuous Emulsion Polymerization of Chlorotrifluoroethylene, Vinyl Acetate, Butyl Acrylate, Veova 10 and Acrylic Acid.

    Science.gov (United States)

    Liu, Hongzhu; Bian, Jiming; Wang, Zhonggang; Hou, Chuan-Jin

    2017-01-22

    Waterborne fluoropolymer emulsions were synthesized using the one-step semi-continuous seed emulsion polymerization of chlorotrifluoroethylene (CTFE), vinyl acetate (VAc), n-butyl acrylate (BA), Veova 10, and acrylic acid (AA). The main physical parameters of the polymer emulsions were tested and analyzed. Characteristics of the polymer films such as thermal stability, glass transition temperature, film-forming properties, and IR spectrum were studied. Meanwhile, the weatherability of fluoride coatings formulated by the waterborne fluoropolymer and other coatings were evaluated by the quick ultraviolet (QUV) accelerated weathering test, and the results showed that the fluoropolymer with more than 12% fluoride content possessed outstanding weather resistance. Moreover, scale-up and industrial-scale experiments of waterborne fluoropolymer emulsions were also performed and investigated.

  19. Tuning the Molar Composition of "Charge-Shifting" Cationic Copolymers Based on 2-(N,N-Dimethylamino)Ethyl Acrylate and 2-(tert-Boc-Amino)Ethyl Acrylate.

    Science.gov (United States)

    Ho, Hien The; Bohec, Maël Le; Frémaux, Julien; Piogé, Sandie; Casse, Nathalie; Fontaine, Laurent; Pascual, Sagrario

    2017-03-01

    Copolymers of 2-(N,N-dimethylamino)ethyl acrylate (DMAEA) and 2-(tert-Boc-amino)ethyl acrylate (tBocAEA) are synthesized by reversible addition-fragmentation chain transfer polymerization in a controlled manner with defined molar masses and narrow molar masses distributions (Ð ≤ 1.17). Molar compositions of the P(DMAEA-co-tBocAEA) copolymers are assessed by means of (1) H NMR. A complete screening in molar composition is studied from 0% of DMAEA to 100% of DMAEA. Reactivity ratios of both comonomers are determined by the extended Kelen-Tüdos method (r DMAEA = 0.81 and rtBocAEA = 0.99). © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Preparation, Characterization and Permeation Behavior of Poly(methyl acrylate-Poly(dimethyl siloxane-Poly(methyl acrylate Block Copolymer/Poly(vinyl acetate Blend Membranes

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Semsarzadeh

    2015-03-01

    Full Text Available Structure of polymeric materials is of the most important factors in determination of the characteristics and properties of the membranes. Various research and developments on polymeric membranes confirm the direct correlation between structure-properties of polymeric membranes. In this research, the structural outcome of poly(methyl acrylate-poly(dimethyl siloxane-poly(methyl acrylate/poly(vinyl acetate blend membranes and its relationship with gas permeation behavior of the blends were investigated. The flexible block copolymer of poly(methyl acrylate-poly(dimethyl siloxane-poly(methyl acrylate (PMA-PDMS-PMA was synthesized via atom transfer radical polymerization. Morphology and chemical structure of the synthesized block copolymer was investigated by Fourier transform infrared spectroscopy, proton nuclear magnetic resonance, gel permeation chromatography, X-ray diffraction analysis, differential scanning calorimetry and scanning electron microscopy. Blend membranes of PMA-PDMS-PMA and poly(vinyl acetate (PVAc were prepared by solution casting method in different compositions. By adding poly(vinyl acetate to PMA-PDMS-PMA block copolymer, the selectivity of the membranes for carbon dioxide/methane pair gases were increased by 55%. Fractional free volume (an indication of chain packing efficiency in blend membranes and dielectric constant (an indication of the molar volume and molar polarization of the blend membranes were obtained as the factors reflected the microstructural effect of PMA-PDMS-PMA and PVAc blend membranes. The efforts were directed toward expressing more precise structure-properties relationship of PMA-PDMS-PMA/PVAc blend membranes. The experimental permeability values of the blend membranes reported in this research were compared with the modified logarithmic model. The modified logarithmic model was evaluated for other blend membranes.

  1. Determination of Monomers Reactivity Ratios in Ethyl Acrylate-Methacrylic Acid Copolymerization by Off-Line 1H NMR

    Directory of Open Access Journals (Sweden)

    Samaneh Ashenagar

    2017-03-01

    Full Text Available The physical, chemical and mechanical properties of polymer systems depend on the micro-structural characteristics of their macromolecular chains. Along with the most characteristic kinetic parameters in copolymerization reactions are the reactivity ratios, which give a clear idea of the average composition and the monomer sequence distribution in copolymer systems. This research studies the solution radical copolymerization of methacrylic acid (MAA-ethyl acrylate (EA system at low conversion with 2,2'-azobisisobutyronitrile (AIBN as thermal initiator at 60°C in deuterated dimethyl sulfoxide (DMSO-d6 as a reaction solvent. In this case, the monomer reactivity ratios were determined using linear off-line 1H nuclear magnetic resonance spectroscopy (1H NMR methods such as Mayo-Louis, Finemann-Ross, Inverted Finemann-Ross , Ezrielev-Brokhina-Roskin, Joshi-Joshi, Kelen-Tudos, extended Kelen- Tudos, Mao-Huglin at low and high conversions. The next estimation process in off-line 1H NMR methods were performed by applying techniques based on ordinary least square (OLS and generalized least square (GLS. The results showed that the GLS approach compared to the OLS increased regression coefficients (R2 and the order of magnitude of parameter variances obtained from GLS was many times lower than that obtained from OLS. In addition, the monomer reactivity ratios obtained by the Mao-Huglin method and the GLS approach showed the best linear estimation.

  2. A preliminary study of the composition of commercial oil, acrylic and vinyl paints and their behaviour after accelerated ageing conditions

    Directory of Open Access Journals (Sweden)

    Francesca Caterina Izzo

    2014-12-01

    Full Text Available This study is part of a research project dealing with the establishment of monitoring and damage prevention plans for contemporary artworks. For this purpose, some commercial paints, among the most currently used by young artists, were selected: Winton oil paint (Winsor & Newton, UK, Heavy Body acrylic paint (Liquitex, USA and Flashe vinyl paint (Lefranc & Bourgeois, France. The paints were subjected to different treatments of accelerated ageing, the results indicating different behaviour in relation both to the type of binders and pigments present in the different formulations. In particular, it was observed that ageing produced by ozone plays an important role in the stability of the oil paints, above all in those containing organic azo pigments. Thermal ageing, as expected, influences the stability of all the commercial paints examined, with the formation of alteration products and visible changes in the paint films. Ageing produced by moisture clearly affects the synthetic polymer-based paints, particularly evident in the changes in mass. In all cases, the accelerated ageing treatments produced chromatic variations, more evidently for the oil paints containing organic pigment.

  3. Evaluation of thermal conductivity of heat-cured acrylic resin mixed with A1203

    Directory of Open Access Journals (Sweden)

    Ebadian B.

    2002-08-01

    Full Text Available One of the most important characteristics of denture base is thermal conductivity. This property has a major role in secretions of salivary glands and their enzymes, taste of the food and gustatory response. Polymethyl methacrylate used in prosthodontics is relatively an insulator. Different materials such as metal fillers and ceramics have been used to solve this problem. The aim of this study was the evaluation of AI2O3 effect on thermal conductivity of heat-cured acrylic resin. Acrylic resin was mixed with AI2O3 in two different weight rates (15 and 20 % of weight. So, group 1 and 2 were divided on this basis. Samples with pure acrylic resin were considered as control group. 18 cylindrical patterns were made in 9x9 mm dimensions and thermocouple wires embedded in each sample to act as conductor. The specimens were put in water with 70±1°C thermal range for 10 minutes. Then, thermal conductivity was measured. The results were analyzed with variance analysis and Dunken test. There was significant difference between thermal conductivity of all groups in all period times. It the first seconds, thermal conductivity in groups 1 and 2 were more than control group. Therefore, for developing of thermal conductivity of acrylic resin, A1203 can be used. Certainly, other characteristic of new resin should be evaluated.

  4. Assessment of the flexural strength of two heat-curing acrylic resins for artificial eyes

    Directory of Open Access Journals (Sweden)

    Aline Úrsula Rocha Fernandes

    2009-09-01

    Full Text Available Prosthetic eyes are artificial substitutes for the eyeball, made of heat-curing acrylic resin, serving to improve the esthetic appearance of the mutilated patient and his/her inclusion in society. The aim of this study was to assess the flexural strength of two heat-curing acrylic resins used for manufacturing prosthetic eyes. Thirty-six specimens measuring 64 x 10 x 3.3 mm were obtained and divided into four groups: acrylic resin for artificial sclera N1 (Artigos Odontológicos Clássico, São Paulo, SP, Brazil, heat-cure water technique (GI and microwave-cured (GII; colorless acrylic resin for prosthetic eyes (Artigos Odontológicos Clássico, São Paulo, SP, Brazil, heat-cure water technique (GIII and microwave-cured (GIV. Mechanical tests using three point loads were performed in a test machine (EMIC, São José dos Pinhais, PR, Brazil. The analysis of variance and the Tukey test were used to identify significant differences (p < 0.01. Groups GII and GIV presented, respectively, the highest (98.70 ± 11.90 MPa and lowest means (71.07 ± 8.93 MPa, with a statistically significant difference. The cure method used for the prosthetic eye resins did not interfere in their flexural strength. It was concluded that all the resins assessed presented sufficient flexural strength values to be recommended for the manufacture of prosthetic eyes.

  5. The removable acrylic partial denture in primary care: the experience and satisfaction of dental surgeons

    Directory of Open Access Journals (Sweden)

    Rita de Cássia SILVA

    2017-11-01

    Full Text Available Abstract Introduction The guidelines of the National Politics of Oral Health have led to the inclusion of elemental prostheses in the list of Primary Care procedures. Objective This paper aimed to evaluate the performance and satisfaction of dental surgeons with the implementation of Acrylic Partial Dentures. Metodology The sample was composed by 159 dental surgeons (sample calculation, in Belo Horizonte, MG, Brazil, selected via raffle (simple random sampling. A structured questionnaire was built with 72 questions on the daily practice of the performance of dental surgeons, using the SurveyMonkey platform. Result The results showed that for most of dental surgeons, the inclusion on the list of primary care procedures was a positive initiative and they have enjoyed the experience of using Acrylic Partial Dentures. Dental surgeons who had graduated in private institutions reported to have had more failures than those who had graduated in public institutions. The better prepared dental surgeons reported less difficulties and failures, and the more satisfied professionals with the performance of Acrylic Partial Dentures related had also experienced fewer failures. Considering the indication, the majority of participants did it according to the protocol of the institution (only for anterior teeth but many revealed the use of dentures also for premolars. Conclusion Acrylic partial dentures have been a reality in the Brazilian social context even before their inclusion in the list of Primary Care procedures. Such inclusion indicates their relevance; however, it is necessary to have their confection systematized by a protocol in public services.

  6. Bio-based acrylic acid from sugar via propylene glycol and allyl alcohol

    NARCIS (Netherlands)

    Pramod, C. V.; Fauziah, R.; Seshan, K.; Lange, J. P.

    2018-01-01

    A new route for producing bio-based acrylic acid is proposed. It starts with the conversion of carbohydrates to propylene glycol, being main or by-product, and proceeds via a subsequent dehydration to allyl alcohol under gas-phase conditions over K-modified ZrO2 and a final oxidation over MoWVOx

  7. Allergic contact dermatitis caused by nail acrylates in Europe. An EECDRG study

    DEFF Research Database (Denmark)

    Gonçalo, Margarida; Pinho, André; Agner, Tove

    2018-01-01

    .0%), and at least 11.7% had to leave their jobs. Skin lesions involved the hands in 121 patients (88.9%) and the face in 50 (36.8%), with the face being the only affected site in 14 (10.3%). Most patients reacted to two or more acrylates on patch testing, mainly to 2-hydroxyethyl methacrylate (HEMA) (92.5%), 2...... of ACD caused by nail acrylates diagnosed by aimed testing between 2013 and 2015. RESULTS: Among 18 228 studied patients, 136 had ACD caused by nail acrylates (0.75%; 95%CI: 0.60-0.90), representing 67.3% (95%CI: 60.4-73.7) of ACD cases caused by acrylates. There were 135 females and 1 male, with a mean...... age ± standard deviation of 36.7 ± 12.2 years; 59 (43.4%) were exposed as consumers, and 77 (56.6%) were occupationally exposed. Occupational cases were more frequent in southern Europe (83.7%), and were younger (mean age of 33.4 ± 8.9 years); most developed ACD during the first year at work (65...

  8. Ocean Engineering Studies Compiled 1991. Volume 6. Acrylic Windows - Typical Applications in Pressure Housings

    Science.gov (United States)

    1991-01-01

    edge constraint the least. The unequal contraction of the acrylic hemispheres eventually led Zo failure of tile sphere by elastico -plastic instability...factor of 16 for a 56-ft operational depth. The predicted implosion pressure was arrived at by considering independently both the elastico -plastic

  9. Acrylic acid surface-modified contact lens for the culture of limbal stem cells.

    Science.gov (United States)

    Zhang, Hong; Brown, Karl David; Lowe, Sue Peng; Liu, Guei-Sheung; Steele, David; Abberton, Keren; Daniell, Mark

    2014-06-01

    Surface treatment to a biomaterial surface has been shown to modify and help cell growth. Our aim was to determine the best surface-modified system for the treatment of limbal stem cell deficiency (LSCD), which would facilitate expansion of autologous limbal epithelial cells, while maintaining cultivated epithelial cells in a less differentiated state. Commercially available contact lenses (CLs) were variously surface modified by plasma polymerization with ratios of acrylic acid to octadiene tested at 100% acrylic acid, 50:50% acrylic acid:octadiene, and 100% octadiene to produce high-, mid-, and no-acid. X-ray photoelectron spectroscopy was used to analyze the chemical composition of the plasma polymer deposited layer. Limbal explants cultured on high acid-modified CLs outgrew more cells. Immunofluorescence and RT2-PCR array results indicated that a higher acrylic acid content can also help maintain progenitor cells during ex vivo expansion of epithelial cells. This study provides the first evidence for the ability of high acid-modified CLs to preserve the stemness and to be used as substrates for the culture of limbal cells in the treatment of LSCD.

  10. Removal of methyl acrylate by ceramic-packed biotrickling filter and their response to bacterial community.

    Science.gov (United States)

    Wu, Hao; Yin, Zhenhao; Quan, Yue; Fang, Yingyu; Yin, Chengri

    2016-06-01

    Methyl acrylate is a widely used raw chemical materials and it is toxic in humans. In order to treat the methyl acrylate waste gas, a 3-layer BTF packed with ceramic particles and immobilized with activated sludge was set up. The BTF exhibited excellent removal efficiency that no methyl acrylate could be detected when EBRT was larger than 266s and inlet concentration was lower than 0.19g/m(3). The 1st layer performed the best at fixed inlet concentration of 0.42g/m(3). PCR combined with DGGE was performed to detect the differences in different layers of the BTF. Phylum Proteobacteria (e.g. α-, β-, γ-, δ-) was predominantly represented in the bacterial community, followed by Actinobacteria and Firmicutes. Desulfovibrio gigas, Variovorax paradoxus, Dokdonella koreensis, Pseudoxanthomonas suwonensis, Azorhizobium caulinodans, Hyphomicrobium denitrificans, Hyphomicrobium sp. and Comamonas testosteroni formed the bacteria community to treat methyl acrylate waste gas in the BTF. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Theoretical study for OH radical-initiated atmospheric oxidation of ethyl acrylate.

    Science.gov (United States)

    Sun, Yanhui; Zhang, Qingzhu; Hu, Jingtian; Chen, Jianmin; Wang, Wenxing

    2015-01-01

    OH radical-initiated atmospheric oxidation of ethyl acrylate (ethyl 2-propenoate, EA) has been investigated by performing density functional theory (DFT) calculations. Optimizations of the reactants, intermediates, transition states and products were carried out at the MPWB1K/6-31+G(d,p) level. Single-point energy calculations were performed at the MPWB1K/6-311+G(3df,2p) level of theory. The detailed oxidation mechanism was presented and discussed. The results show that the OH addition is more energetically favorable than the H abstraction. Rice-Ramsperger-Kassel-Marcus (RRKM) theory was used to predict the rate constants over the possible atmospheric temperature range of 180-370 K. The Arrhenius expression adequately describes the total rate constant: k(EA+OH)=(1.71×10(-12))exp(805.42/T)cm(3) molecule(-1) s(-1). At 298 K, the atmospheric lifetime of ethyl acrylate determined by OH radicals is about 16.2h. In order to find out the effect of alkyl substitution on the reaction activity, rate constants for the reactions of methyl acrylate, methyl methacrylate and butyl acrylate with OH radicals were also discussed. Calculation results show that the reaction activity may increase with the increased electron-donating substitution for electrophilic addition reaction. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Polymer coating comprising 2-methoxyethyl acrylate units synthesized by surface-initiated atom transfer radical polymerization

    DEFF Research Database (Denmark)

    2011-01-01

    Source: US2012184029A The present invention relates to preparation of a polymer coating comprising or consisting of polymer chains comprising or consisting of units of 2-methoxyethyl acrylate synthesized by Surface-Initiated Atom Transfer Radical Polymerization (SI ATRP) such as ARGET SI ATRP...

  13. The Cherenkov correlated timing detector beam test results from quartz and acrylic bars

    CERN Document Server

    Sugaya, Y; Yoshimura, Y; Kanda, S; Olsen, S; Ueno, K; Varner, G S; Bergfeld, T; Bialek, J J; Lorenc, J; Palmer, M; Rudnick, G; Selen, M; Auran, T; Boyer, V; Honscheid, K; Tamura, N; Yoshimura, K; Lü, C; Marlow, D R; Mindas, C R; Prebys, E J; Asai, M; Kimura, A; Hayashi, S

    1995-01-01

    Several prototypes of a Cherenkov Correlated Timing (CCT) Detector have been tested at the KEK-PS test beam line. We describe the results for Cherenkov light yields and timing characteristics from quartz and acrylic bar prototypes. A Cherenkov angle resolution is found to be 15 mrad at a propagation distance of 100 cm with a 2 cm thick quartz bar prototype.

  14. Polymorphism and polymerisation of acrylic and methacrylic acid at high pressure

    DEFF Research Database (Denmark)

    Oswald, Iain D. H.; Urquhart, Andrew J.

    2011-01-01

    The polymorphism and polymerisation of two related acids have been investigated under high pressure conditions. Acrylic acid crystallises as a new polymorph at 0.65 GPa whilst methacrylic acid crystallises in a new polymorph at a higher pressure of 1.5 GPa. Both these new polymorphs exhibit similar...

  15. The Effects of Silicone and Acrylic Ear Mold Materials on Outer Ear Canal Resonance Characteristics.

    Science.gov (United States)

    Alnıaçık Erdoğan, Asuman; Arslan, Şeyda Nur

    2016-08-01

    The aim of this study is to investigate the effects of earmolds made of silicone and acrylic on outer ear canal resonance characteristics in terms of resonance frequency and amplitude measured in a hearing aid fitting. Outer ear canal resonance frequencies and amplitudes in open ears and those measured with silicone and acrylic ear molds were obtained from 30 participants between the ages of 20 and 25 years (average age, 22.0 years; 18 females and 12 males) with a real ear gain measurement. To observe the changes depending on probe tube placement, test-retest variation was investigated in 10 participants before the study. There was no statistically significant difference between open ear canal resonance frequencies and those measured with silicone and acrylic earmolds (p>0.05). the silicone earmold resonance amplitude values were statistically significantly lower than the open ear canal resonance amplitudes when compared to those of the acrylic earmolds (p<0.05). Depending on the changes occurring in outer ear resonance features as a result of earmold materials used in hearing aid fittings, the application of earmolds should be done by experienced specialists.

  16. Deep UV patterning of acrylic masters for molding biomimetic dry adhesives

    Science.gov (United States)

    Sameoto, D.; Menon, C.

    2010-11-01

    We present a novel fabrication method for the production of biomimetic dry adhesives that allows enormous variation in fiber shapes and sizes. The technology is based on deep-UV patterning of commercial acrylic with semi-collimated light available from germicidal lamps, and combined careful processing conditions, material selection and novel developer choices to produce relatively high-aspect-ratio fibers with overhanging caps on large areas. These acrylic fibers are used as a master mold for subsequent silicone rubber negative mold casting. Because the bulk acrylic demonstrates little inherent adhesion to silicone rubbers, the master molds created in this process do not require any surface treatments to achieve high-yield demolding of interlocked structures. Multiple polymers can be cast from silicone rubber negative molds and this process could be used to structure smart materials on areas over multiple square feet. Using direct photopatterning of acrylic allows many of the desired structures for biomimetic dry adhesives to be produced with relative ease compared to silicon-based molding processes, including angled fibers and hierarchical structures. Optimized fiber shapes for a variety of polymers can be produced using this process, and adhesion measurements on a well-characterized polyurethane, ST-1060, are used to determine the effect of fiber geometry on adhesion performance.

  17. New hybrid latexes from a soybean oil-based waterborne polyurethane and acrylics via emulsion polymerization.

    Science.gov (United States)

    Lu, Yongshang; Larock, Richard C

    2007-10-01

    A series of new waterborne polyurethane (PU)/acrylic hybrid latexes have been successfully synthesized by the emulsion polymerization of acrylic monomers (butyl acrylate and methyl methacrylate) in the presence of a soybean oil-based waterborne PU dispersion using potassium persulfate as an initiator. The waterborne PU dispersion has been synthesized by a polyaddition reaction of toluene 2,4-diisocyanate and a soybean oil-based polyol (SOL). The resulting hybrid latexes, containing 15-60 wt % SOL as a renewable resource, are very stable and exhibit uniform particle sizes of 125 +/- 20 nm as determined by transmittance electronic microscopy. The structure, thermal, and mechanical properties of the resulting hybrid latex films have been investigated by Fourier transform infrared spectroscopy, solid state 13C NMR spectroscopy, dynamic mechanical analysis, extraction, and mechanical testing. Grafting copolymerization of the acrylic monomers onto the PU network occurs during the emulsion polymerization, leading to a significant increase in the thermal and mechanical properties of the resulting hybrid latexes. This work provides a new way of utilizing renewable resources to prepare environmentally friendly hybrid latexes with high performance for coating applications.

  18. Biocompatibility of a new radiopaque iodine-containing acrylic bone cement

    NARCIS (Netherlands)

    van Hooy-Corstjens, Catharina S. J.; Bulstra, Sjoerd K.; Knetsch, Menno L. W.; Geusens, Piet; Kuijer, Roel; Koole, Leo H.

    Radiopacity in the vast majority of the commercially available acrylic bone cements that are used clinically is provided by particles of either BaSO4 or ZrO2. Literature reports have shown these agents to have a detrimental effect on some mechanical properties of the cements as well as on its

  19. Thermal behavior of flax and jute reinforced in matrix acrylic composite

    Czech Academy of Sciences Publication Activity Database

    Samal, Sneha Manjaree; Stuchlík, M.; Petrikova, I.

    2017-01-01

    Roč. 131, č. 2 (2017), s. 1-6 ISSN 1388-6150 Institutional support: RVO:68378271 Keywords : flax * jute * acrylic resin * composite * DMA * TG * FTIR Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.953, year: 2016

  20. Assessment of the flexural strength of two heat-curing acrylic resins for artificial eyes.

    Science.gov (United States)

    Fernandes, Aline Ursula Rocha; Portugal, Aline; Veloso, Letícia Rocha; Goiato, Marcelo Coelho; Santos, Daniela Micheline dos

    2009-01-01

    Prosthetic eyes are artificial substitutes for the eyeball, made of heat-curing acrylic resin, serving to improve the esthetic appearance of the mutilated patient and his/her inclusion in society. The aim of this study was to assess the flexural strength of two heat-curing acrylic resins used for manufacturing prosthetic eyes. Thirty-six specimens measuring 64 x 10 x 3.3 mm were obtained and divided into four groups: acrylic resin for artificial sclera N1 (Artigos Odontológicos Clássico, São Paulo, SP, Brazil), heat-cure water technique (GI) and microwave-cured (GII); colorless acrylic resin for prosthetic eyes (Artigos Odontológicos Clássico, São Paulo, SP, Brazil), heat-cure water technique (GIII) and microwave-cured (GIV). Mechanical tests using three point loads were performed in a test machine (EMIC, São José dos Pinhais, PR, Brazil). The analysis of variance and the Tukey test were used to identify significant differences (p < 0.01). Groups GII and GIV presented, respectively, the highest (98.70 +/- 11.90 MPa) and lowest means (71.07 +/- 8.93 MPa), with a statistically significant difference. The cure method used for the prosthetic eye resins did not interfere in their flexural strength. It was concluded that all the resins assessed presented sufficient flexural strength values to be recommended for the manufacture of prosthetic eyes.

  1. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Science.gov (United States)

    2010-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is... part apply to this section except as modified by this paragraph. (1) Recordkeeping. Recordkeeping...

  2. 40 CFR 721.465 - Alkoxylated alkylpolyol acrylates, adduct with alkylamine (generic).

    Science.gov (United States)

    2010-07-01

    ... PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES... substances identified generically as alkoxylated alkylpolyol acrylates, adduct with alkylamine (PMNs P-98... provisions of subpart A of this part apply to this section except as modified by this paragraph. (1...

  3. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Science.gov (United States)

    2010-07-01

    ...). 721.338 Section 721.338 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC... subject to reporting. (1) The chemical substances identified generically as salt of an acrylate copolymer...) Specific requirements. The provisions of subpart A of this part apply to this section except as modified by...

  4. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Science.gov (United States)

    2010-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject to... of this part apply to this section except as modified by this paragraph. (1) Recordkeeping...

  5. Color Stability of Heat‑cure Acrylic Resin Subjected to Simulated ...

    African Journals Online (AJOL)

    Background: Regular usage of denture cleansers is recommended in complete denture wearers for effective plaque control, and these cleansers alter the physical properties of acrylic resin over a period of time. Thus, an in vitro study was carried out to assess the effect of denture cleansers on the color stability of heat‑cure ...

  6. Propagation of ultrasonic guided waves in an acrylic plate as a cortical-bone-mimicking phantom

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kang Il [Kangwon National University, Chuncheon (Korea, Republic of); Choi, Bok Kyoung [Maritime Security Research Center, KIOST, Ansan (Korea, Republic of)

    2014-12-15

    The present study aims to investigate the propagation of ultrasonic guided waves in an acrylic plate as a cortical-bone-mimicking phantom. The velocities of the guided waves in a 5-mm-thick acrylic plate were measured by using the axial transmission technique. A pure A0 Lamb mode could be successfully launched in the 5-mm-thick acrylic plate through a time reversal process of Lamb waves, consistent with the fact that the time reversal process can automatically compensate for the dispersive nature of Lamb waves. The experimental velocities of the slow guided wave (SGW) and the time-reversed Lamb wave were found to be in reasonable agreement with the theoretical group velocity of the A0 Lamb mode, suggesting that both the SGW and the time-reversed Lamb wave excited in the 5-mm-thick acrylic plate correspond to the A0 Lamb mode. These results suggest that the time reversal process of Lamb waves can be usefully applied to noninvasive characterization of long cortical bones.

  7. Computational study of the self-initiation mechanism in thermal polymerization of methyl acrylate.

    Science.gov (United States)

    Srinivasan, Sriraj; Lee, Myung Won; Grady, Michael C; Soroush, Masoud; Rappe, Andrew M

    2009-10-08

    This computational study deals with the mechanism of spontaneous initiation in thermal polymerization of alkyl acrylates (e.g., methyl, ethyl, and n-butyl acrylate). The mechanism is presently still unknown. Density-functional theory (DFT) and Møller-Plesset (MP2) calculations are used to explore the Flory and Mayo mechanisms of self-initiation in methyl acrylate. On the singlet surface, a low-barrier, concerted [4 + 2] Diels-Alder mechanism for the formation of a dihydropyran adduct (DA) and a high-barrier nonconcerted [2 + 2] diradical ((*)M(2s)(*)) mechanism for the formation of dimethyl cyclobutane-1,2-dicarboxylate (DCD) were found using B3LYP/6-31G*. Several levels of theory were used to validate the transition states, and the pathways for the DA and DCD formations on the singlet surface were determined using intrinsic reaction coordinate (IRC) calculations. On the triplet surface, a triplet diradical intermediate ((*)M(2t)(*)) was identified that is structurally similar to (*)M(2s)(*) but lower in energy. The spin-orbit coupling constant for crossover of the diradical from singlet to triplet surface was calculated. Monoradical generation from the two intermediates, DA and (*)M(2t)(*) via hydrogen transfer to or from a third methyl acrylate was studied. It was found that generation of two monoradical species was possible from (*)M(2t)(*) and is proposed as a likely explanation for experimentally observed spontaneous-initiation.

  8. Morphological alteration of microwave disinfected acrylic resins used for dental prostheses

    Science.gov (United States)

    Popescu, M. C.; Bita, B. I.; Avram, A. M.; Tucureanu, V.; Schiopu, P.

    2015-02-01

    In this paper we aim to perform a cross section morphological characterization of an acrylic polymer used for dental prostheses subjected to microwave disinfection. The method was largely investigated and the microbiological effectiveness is well established, but there are some issues regarding the in-depth alteration of the material. In our research, the surface roughness is insignificant and the samples were not polished or refined by any means. Two groups of 7 acrylic discs (20 mm diameter, 2 mm thickness) were prepared from a heat-cured powder. Half of the samples embedded a stainless steel reinforcement, in order to observe the changes at the interfaces between the polymer and metallic wire. After the gradual wet microwave treatment, the specimens - including the controls - were frozen in liquid nitrogen and broken into pieces. Fragments were selected for gold metallization to ensure a good contrast for SEM imaging. We examined the samples in cross section employing a high resolution SEM. We have observed the alterations occurred at the surface of the acrylic sample and at the interface with the metallic wire along with the increase of the power and exposure time. The bond configuration of acrylate samples was analysed by FTIR spectrometry.

  9. In vitro release of doxycycline from bioabsorbable materials and acrylic strips

    DEFF Research Database (Denmark)

    Larsen, T

    1990-01-01

    Treatment of marginal periodontitis may include use of local antibiotics. In the present in vitro study the bioabsorbable materials Surgicel, Tissell, and CollaCote and acrylic strips were examined for release of doxycycline into liquids and residual antibacterial activity of the materials. Piece...

  10. Catalytic acetoxylation of lactic acid to 2-acetoxypropionic acid, en route to acrylic acid

    NARCIS (Netherlands)

    Beerthuis, R.; Granollers, M.; Brown, D.R.; Salavagione, H.J.; Rothenberg, G.; Shiju, N.R.

    2015-01-01

    We present an alternative synthetic route to acrylic acid, starting from the platform chemical lactic acid and using heterogeneous catalysis. To improve selectivity, we designed an indirect dehydration reaction that proceeds via acetoxylation of lactic acid to 2-acetoxypropionic acid. This

  11. Fast-Curing Epoxy and Acrylate Adhesive Development for Adverse Marine Conditions

    Science.gov (United States)

    2013-07-01

    acrylic adhesive with fast cure and a high peel strength. Chemical structure: methyl methacrylate; synthetic polymer; 3,5-diethyl- 1,2-dihydro-1...Original Weight Original Weight X 100 5 2.6 Substrate Preparation All-aluminum specimen plates were abrasive blasted using 180-grit aluminum oxide

  12. Termite and fungal resistance of in situ polymerized tributyltin acrylate and acetylated Indonesian and USA wood

    Science.gov (United States)

    Rebecca E. Ibach; Yusuf Sudo. Hadi; Dodi. Nandika; Sulaeman. Yusuf; Yuliati. Indrayani

    2000-01-01

    Wood [Indonesian pine (IP), Indonesian Jabon (IJ) and USA southern yellow pine (USP)] was either in situ polymerized with tributyltin acrylate (TBTA) or acetylated and then exposed to termite and fungal degradation both in laboratory tests and field exposure. The TBTA woods had an average weight percent gain (WPG) of 11% for IP, 12% for IJ, and 10% for USP. The...

  13. Dielectric properties of solution-grown-undoped and acrylic-acid ...

    Indian Academy of Sciences (India)

    Dielectric capacities and losses were measured, in the temperature (50–170°C) and frequency (01–100 kHz range), for undoped and acrylic acid (AA) doped ethyl cellulose (EC) films (thickness about 20 m) with progressive increase in the concentration of dopant in the polymer matrix. The variation of capacity with ...

  14. Optical properties and indentation hardness of thin-film acrylated epoxidized oil

    Science.gov (United States)

    Rahman, Mohammad Syuhaimi Ab.; Shaktur, Khaled Mohamed; Mohammad, Rahmah; Zalikha, Wan Aimi; Nawi, Norwimie; Mohd, Ahmad Faiza

    2012-02-01

    Epoxy acrylate has been widely used as optical resin for applications such as cladding, the core of a waveguide, and other photonic devices. In this study, sustainable resin from edible oil was used as an alternative to epoxy acrylate. Structural features and the transmission of planar thin-film resin from an ultraviolet-visible spectroscopy (UV-VIS) spectrometer were investigated upon UV exposure. It was found that high transmission still persists for all samples with and without an UV absorber for exposed and unexposed samples. The film was found to absorb strongly below 400 nm. A change in the cut-off wavelength was observed upon exposure. Thin-film hardness and its dynamic indentation in the load-unload mode with different test forces were evaluated. Vickers hardness and the elastic modulus were determined for unacrylated epoxidized soybean oil (ESO) and acrylated epoxidized soybean oil (AESO). It was found that the AESO has a higher Vickers hardness and elastic modulus than those of unacrylated thin film. The Vickers hardness and elastic modulus were found to increase as the applied test force increased. The refractive index, thickness, and modes present were characterized from a spin-coated planar thin film. The refractive index in the transverse electric mode (TE) and transverse magnetic mode (TM) were determined and compared for unacrylated and acrylated epoxidized oil.

  15. PHOTORESPONSIVE BEHAVIOR OF AZOBENZENE-BASED (METH)ACRYLIC (CO)POLYMERS IN THIN-FILMS

    NARCIS (Netherlands)

    HAITJEMA, HJ; VONMORGEN, GL; TAN, YY; CHALLA, G

    1994-01-01

    The reversible photoisomerization and the thermal isomerization of azobenzene-based (Az.b.) groups covalently bound to (meth)acrylic (co)polymers were investigated in thin films. For the amorphous polymers it was found that a broad range of the thermal cis --> trans isomerization rates could be

  16. Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin.

    Science.gov (United States)

    Goiato, Marcelo C; Dos Santos, Daniela M; Baptista, Gabriella T; Moreno, Amália; Andreotti, Agda M; Bannwart, Lisiane C; Dekon, Stefan F C

    2013-12-01

    The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n = 7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60 days. All specimens were thermal cycled between 5 and 55°C with 30-s dwell times for 1000 cycles before and after disinfection. The specimens' colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T1 ), after disinfection (D) and after second thermal cycling (T2 ). Colour differences (ΔE) were calculated between T1 and B (T1 B), D and B (DB), and T2 and B (T2 B) time-points.   The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time-points, except for the Lucitone acrylic resin. The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters. © 2012 John Wiley & Sons A/S and The Gerodontology Society. Published by John Wiley & Sons Ltd.

  17. The effect of bioburden on in-depth disinfection of denture base acrylic resin.

    Science.gov (United States)

    Saunders, T R; Guillory, V L; Gregoire, S T; Pimsler, M; Mitchell, M S

    1998-11-01

    This study evaluated the effectiveness of three different disinfectant solutions against denture bioburden absorbed within the depth of acrylic resin. Specimens were taken from dentures that had been worn by the patients for 15 to 20 years and were scheduled for replacement.

  18. Designing temperature-responsive biocompatible copolymers and hydrogels based on 2-hydroxyethyl(meth)acrylates.

    Science.gov (United States)

    Khutoryanskaya, Olga V; Mayeva, Zarina A; Mun, Grigoriy A; Khutoryanskiy, Vitaliy V

    2008-12-01

    Free-radical copolymerization of 2-hydroxyethyl methacrylate with 2-hydroxyethyl acrylate can be successively utilized for the synthesis of water-soluble polymers and hydrogels with excellent physicochemical properties, thus showing promise for pharmaceutical and biomedical applications. In the work presented it has been demonstrated that water-soluble copolymers based on 2-hydroxyethyl methacrylate and 2-hydroxyethyl acrylate exhibit lower critical solution temperature in aqueous solutions, whereas the corresponding high molecular weight homopolymers do not have this unique property. The temperature-induced transitions observed upon heating the aqueous solutions of these copolymers proceed via liquid-liquid phase separation. The hydrogels were also synthesized by copolymerizing 2-hydroxyethyl methacrylate and 2-hydroxyethyl acrylate in the absence of a bifunctional cross-linker. The cross-linking of these copolymers during copolymerization is believed to be due to the presence of bifunctional admixtures or transesterification reactions. Transparency, swelling behavior, mechanical properties, and porosity of the hydrogels are dependent upon the monomer ratio in the copolymers. Hydrogel samples containing more 2-hydroxyethyl methacrylate are less transparent, have lower swelling capacity, higher elastic moduli, and pores of smaller size. The assessment of the biocompatibility of the copolymers using the slug mucosal irritation test revealed that they are also less irritant than poly(acrylic acid).

  19. Screening of Catalyst and Important Variable for The Esterification of Acrylic Acid with 2 Ethylhexanol

    Science.gov (United States)

    Ahmad, M. A. A.; Chin, S. Y.

    2017-06-01

    The global demand of 2-ethylhexyl acrylate (2EHA) market has witnessed a significant growth in the past few years and this growth is anticipated to increase in the coming years. 2EHA is one of the basic organic building blocks that mainly used in the production of coatings, adhesives, superabsorbents, thickeners and plastic additives. Homogenous acid-catalysed esterification of acrylic acid (AA) with 2-ethylhexanol (2EH) is commonly used for the production of 2EHA. The homogeneous catalysts such as sulfuric and para-toluene sulfonic acid have resulted the costly and complicated downstream process that generates acidic, corrosive and non-environmental friendly waste. Therefore, it is importance to develop a cheaper process that employing heterogeneous catalysts and alternative raw material from wastewater containing acrylic acid. In this research, the study for the esterification of AA with 2EH catalysed by ion-exchange resin was conducted. The best sulfonic acid functional cation-exchange resin among SK104, SK1B, PK208, PK216, PK228, RCP145, and RCP160 was screened. PK208 outperformed the other resins and it was used subsequently in the parametric studies. The effect of important parameters (initial concentration of acrylic acid (AA), temperature, molar ratio of reactant (AA and 2EH), catalyst loading, and polymerisation inhibitor loading) was studied using 2 factorial design to determine the significant parameters to the esterification. It was found that the initial concentration of AA and temperature were most significantly affecting the esterification of AA with 2EH.

  20. An effective method and pathways of acrylonitrile degradation to acrylic acid through an alkaline hydrothermal system.

    Science.gov (United States)

    Dong, Wenjie; Peng, Boyu; Wang, Ke; Miao, Jia; Zhang, Wei; Zhang, Yalei; Shen, Zheng

    2017-07-01

    Degradation of pollution for specific chemicals represents an optimal approach to high-strength wastewater treatment. One-pot selective conversion of acrylonitrile to acrylic acid in a hydrothermal system with NaOH as a catalyst was carried out. The influence factors were evaluated, including initial acrylonitrile concentration, reaction temperature, reaction time and amount of alkali. Experimental results showed that the highest yield of acrylic acid (55%) was obtained at the initial acrylonitrile concentration of 3 × 10(3) mg/L, 300°C for 90 s with 1.0 M NaOH. To determine the reaction path, intermediates analysis and calculation of carbon and nitrogen balance were carried out by means of HPLC, GC and TOC/TN methods. Two probable reaction pathways were proposed as follows: (1) Acrylonitrile was hydrolyzed into acrylamide, and acrylic acid was obtained via further hydrolysis. (2) Acrylonitrile was converted into 3-hydroxy-propionitrile via additive reaction, and this product was readily converted to 3-hydroxy-propionic acid through two steps of hydrolysis, followed by dehydration reaction to produce acrylic acid. This study offered not only an efficient method to transfer highly toxic pollutants into valuable chemical, but also a better understanding of hydrothermal alkali catalytic reaction.

  1. Bioconversion of acrylonitrile to acrylic acid by rhodococcus ruber strain AKSH-84.

    Science.gov (United States)

    Kamal, Ahmed; Kumar, M Shiva; Kumar, C Ganesh; Shaik, Thokhir

    2011-01-01

    A new versatile acrylonitrile-bioconverting strain isolated from a petroleum-contaminated sludge sample and identified as Rhodococcus ruber AKSH-84 was used for optimization of medium and biotransformation conditions for nitrilase activity to produce acrylic acid. A simple and rapid HPLC protocol was optimized for quantification of acrylic acid, acrylamide, and acrylonitrile. The optimal medium conditions for nitrilase activity were pH of 7.0, temperature of 30degreesC, agitation of 150 rpm, and inoculum level of 2%. Glycerol as a carbon source and sodium nitrate as the nitrogen source provided good nutritional sources for achieving good biotransformation. Nitrilase activity was constitutive in nature and was in the exponential growth phase after 24 h of incubation under optimal conditions without addition of any inducer. The substrate preference was acrylonitrile and acetonitrile. The present work demonstrates the biotransformation of acrylonitrile to acrylic acid with the new strain, R. ruber AKSH-84, which can be used in green biosynthesis of acrylic acid for biotechnological processes. The nitrilase produced by the isolate was purified and characterized.

  2. Internal Characterization of Denture Base by Using Acrylic Stains and Tissue Paper

    OpenAIRE

    Pattanaik, Seema; Pattanaik, Bikash

    2011-01-01

    Characterization of an artificial denture is required to give the denture a more natural appearance. This article describes the laboratory procedures for internal characterization of denture base in a removable prosthesis using acrylic stains and absorbent tissue paper incorporated in the heat cure polymerizing denture base resin at the stage of packing.

  3. Effect of black tea on the transverse strength of heat-polymerized acrylic resin

    Directory of Open Access Journals (Sweden)

    Eni Rahmi

    2017-11-01

    Full Text Available Introduction: Heat-polymerized acrylic resin is the most basic denture material used. One of the mechanical properties of an acrylic resin is its transverse strength. The transverse strength test provides an overview of the material's durability in accepting the load at mastication. Consumption of tea, especially black tea in the world placed the second most consumed. The purpose of this study was to determine the effect of black tea on the transverse strength of heat-polymerized acrylic resin. Methods: This research was an experimental laboratory with 24 samples of heat-polymerized acrylic resin plate with the size of 65 x 10 x 2.5 mm. The sample was divided into 6 groups, each consisted of 4 samples. The first, second, and the third groups were immersed in aquadest for consecutively 1, 4, and 20 days. The fourth, fifth, and sixth groups were immersed in the black tea for consecutively 1, 4, and 20 days. The transverse strength was tested using the three-point bending method with the Universal Testing Machine. The results of the transverse strength measurement were then analyzed statistically by the One-way ANOVA test and Holm's sequential Bonferroni posthoc test as an advanced test. Results: The results of the statistical test showed that p < 0,05 (p = 0,000 which means that the six groups have a significant difference in the average value of the transverse strength. Conclusion: The conclusion of this research was the black tea immersion duration was affecting the transverse strength difference of the heat-polymerized acrylic resin.

  4. Self-initiation of UV photopolymerization reactions using tetrahalogenated bisphenol A (meth)acrylates.

    Science.gov (United States)

    Pelras, Théophile; Knolle, Wolfgang; Naumov, Sergej; Heymann, Katja; Daikos, Olesya; Scherzer, Tom

    2017-05-17

    The potential of tetrachlorinated and tetrabrominated bisphenol A diacrylates and dimethacrylates for self-initiation of a radical photopolymerization was investigated. The kinetics of the photopolymerization of an acrylic model varnish containing halogenated monomers was studied by real-time FTIR spectroscopy, whereas the formation of reactive species and secondary products was elucidated by laser flash photolysis and product analysis by GC-MS after steady-state photolysis. The interpretation of the experimental data and the analysis of possible reaction pathways were assisted by quantum chemical calculations. It was shown that all halogenated monomers lead to a significant acceleration of the photopolymerization kinetics at a minimum concentration of 5 wt%. Steady-state and laser flash photolysis measurements as well as quantum chemical calculations showed that brominated and chlorinated samples do not follow the same pathway to generate radical species. Whereas chlorinated (meth)acrylates may cleave only at the C-O bonds of the carboxyl groups resulting in acrolein and oxyl radicals for initiation, brominated monomers may cleave either at the C-O bonds or at the C-Br bonds delivering aryl and bromine radicals. The quantum yields for the photolysis of the halogenated monomers were found to be in the order of 0.1 for acrylates and 0.2 for methacrylates (with an estimated error of 25%), independently of the attached Br and Cl halogens. Finally, the trihalogenated bisphenol A di(meth)acrylate radicals and the acrolein radicals were found to show the highest efficiencies for the reaction with another acrylic double bond leading to the formation of a polymer network.

  5. Influence of ozone and paracetic acid disinfection on adhesion of resilient liners to acrylic resin

    Science.gov (United States)

    2016-01-01

    PURPOSE The aim of this study was to evaluate the effect of paracetic acid (PAA) and ozone disinfection on the tensile bond strength (TBS) of silicone-based resilient liners to acrylic resins. MATERIALS AND METHODS One hundred and twenty dumbbell shaped heat-polymerized acrylic resins were prepared. From the mid segment of the specimens, 3 mm of acrylic were grinded off and separated parts were reattached by resilient liners. The specimens were divided into 2 control (control1, control7) and 4 test groups of PAA and ozone disinfection (PAA1, PAA7, ozone1 and ozone7; n=10). While control groups were immersed in distilled water for 10 min (control1) and 7 days (control7), test groups were subjected to PAA (16 g/L) or ozone rich water (4 mg/L) for 1 cycle (10 min for PAA and 60 min for ozone) per day for 7 days prior to tensile tests. Measurements of the TBS were analyzed using 3-way ANOVA and Tukey's HSD test. RESULTS Adhesive strength of Mollosil decreased significantly by application of ozone disinfection. PAA disinfection had no negative effect on the TBS values of Mollosil and Molloplast B to acrylic resin. Single application of ozone disinfection did not have any negative effect on TBS values of Molloplast B, but prolonged exposure to ozone decreased its adhesive strength. CONCLUSION The adhesion of resilient liners to acrylic was not adversely affected by PAA disinfection. Immersion in ozonated water significantly decreased TBS of Mollosil. Prolonged exposure to ozone negatively affects adhesion of Molloplast B to denture base materials. PMID:27555898

  6. Multi-functional hybrid coatings containing silica nanoparticles and anti-corrosive acrylate monomer for scratch and corrosion resistance.

    Science.gov (United States)

    Seo, Ji Yeon; Han, Mijeong

    2011-01-14

    Multi-functional hybrid coatings having both anti-corrosion and scratch resistance were prepared from modified silica nanoparticles and functional acrylates. To improve the dispersion properties of silica nanoparticles in the organic/inorganic hybrid coatings, the surface of the nanoparticles was modified with γ-methacryloxypropyltrimethoxysilane. The coating solution could be prepared by mixing modified silica nanoparticles, tetrasiloxane acrylate, di-acrylate monomer containing an anti-corrosion functional group, acrylic acid, and an initiator in a solvent. The mixture was then dip-coated on iron substrates and finally polymerized by ultraviolet (UV) irradiation. Corrosion and scratch resistance of the coated iron was evaluated by electrochemical impedance spectroscopy (EIS) and a pencil hardness test, respectively. From the EIS results, the coatings with tetrasiloxane acrylate and di-acrylate did not show any decrease in impedance or phase angle, even after 50 days' exposure to 0.1 M NaCl electrolyte, whereas the conventional acrylate coatings started to fail after only 24 h. A hybrid coating containing the amine-quinone functional group exhibited excellent corrosion protection properties with 4-5H pencil hardness.

  7. A Clear Label Strategy for Food Additives : Ingredient Marketing

    NARCIS (Netherlands)

    Diaz, J.

    2016-01-01

    Clear label is a strategic approach that food companies, policy makers and consumer groups can use to bring balance and clarity into food labeling. The first of a two-part report on a clear label strategy.

  8. Nitrogen dynamics in land cleared of alien vegetation ( Acacia ...

    African Journals Online (AJOL)

    Fabaceae family), are currently cleared in South African catchments to reduce water loss and preserve streamflow, and for the restoration of the ecosystem. This study tested the hypothesis that clearing invasive alien vegetation may disturb the ...

  9. Chemical clearing and dehydration of GFP expressing mouse brains

    National Research Council Canada - National Science Library

    Becker, Klaus; Jährling, Nina; Saghafi, Saiedeh; Weiler, Reto; Dodt, Hans-Ulrich

    2012-01-01

    ...) can be applied as a more GFP-friendly clearing medium. Clearing with dibenzyl ether provides improved tissue transparency and strikingly improved fluorescence intensity in GFP expressing mouse brains and other samples as mouse spinal cords, or embryos...

  10. Nd:YAG capsulotomy rates after use of the AcrySof acrylic three piece and one piece intraocular lenses.

    Science.gov (United States)

    Mian, S I; Fahim, K; Marcovitch, A; Gada, H; Musch, D C; Sugar, A

    2005-11-01

    Acrylic lens size and shape may influence the rate of posterior capsule opacification (PCO) and need for Nd:YAG capsulotomy. The aim of this study is to compare the Nd:YAG capsulotomy rate of the three piece acrylic/PMMA AcrySof MA series lens with the one piece acrylic AcrySof SA series lens. 434 eyes of 329 patients who had cataract extraction and implantation of one of four types of intraocular lenses (IOLs) were evaluated for rate of Nd:YAG capsulotomy. 176 eyes received the acrylic AcrySof MA30AC IOL, 71 eyes the acrylic AcrySof MA60AC IOL, 45 eyes the acrylic AcrySof SA30AL IOL, and 142 eyes the acrylic AcrySof SA60AT IOL. The rates of Nd:YAG capsulotomy with the three piece IOL (MA30AC/MA60AC) and the one piece IOL (SA30AL/SA60AT) were 1.2% and 2.1% at 6 months, 2.8% and 5.9% at 12 months, and 3.6% and 7.5% at 24 months, respectively. The incidence of Nd:YAG capsulotomy was higher in patients who received the one piece IOL (p=0.01, log rank test). There was no difference in Nd:YAG capsulotomy rates when comparing lens optic size, age, sex, history of pars plana vitrectomy, and diabetes mellitus. This study shows a greater incidence of Nd:YAG capsulotomy in patients who receive one piece acrylic AcrySof lenses when compared to those who receive three piece acrylic AcrySof lenses.

  11. 17 CFR 16.00 - Clearing member reports.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Clearing member reports. 16.00... MARKETS § 16.00 Clearing member reports. (a) Information to be provided. Each reporting market shall... day, showing for each clearing member, by proprietary and customer account, the following information...

  12. Solubility determination from clear points upon solvent addition

    NARCIS (Netherlands)

    Reus, M.A.; Heijden, A.E.D.M. van der; Horst, J.H. ter

    2015-01-01

    A method is described for determining the solubility of multicomponent crystalline compounds from clear points upon sample dilution at a constant temperature. Clear points are established by continuously adding a solvent mixture to a suspension of known composition until a clear solution appears.

  13. 78 FR 72475 - Derivatives Clearing Organizations and International Standards

    Science.gov (United States)

    2013-12-02

    ....aspx . \\13\\ While Chicago Mercantile Exchange, Inc. (``CME Clearing''), ICE Clear Credit LLC (``ICE... and ICE Clear Credit; the Securities and Exchange Commission (``SEC'') serves as OCC's Supervisory... around the world including, Argentina, Australia, Belgium, Brazil, Canada, China, France, Germany, Hong...

  14. Pre-irradiation induced emulsion co-graft polymerization of acrylonitrile and acrylic acid onto a polyethylene nonwoven fabric

    Science.gov (United States)

    Liu, Hanzhou; Yu, Ming; Ma, Hongjuan; Wang, Ziqiang; Li, Linfan; Li, Jingye

    2014-01-01

    A pre-irradiation induced emulsion co-graft polymerization method was used to introduce acrylonitrile and acrylic acid onto a PE nonwoven fabric. The use of acrylic acid is meant to improve the hydrophilicity of the modified fabric. The kinetics of co-graft polymerization were studied. The existence of polyacrylonitrile (PAN) and poly(acrylic acid) (PAAc) graft chains was proven by Fourier transform infrared spectroscopy (FTIR) analysis. The existence of the nitrile groups in the graft chains indicates that they are ready for further amidoximation and adsorption of heavy metal ions.

  15. Cast Nanostructured Films of Poly(methyl methacrylate-b-butyl acrylate)/Carbon Nanotubes: Influence of Poly(butyl acrylate) Content on Film Evaporation Rate, Morphology, and Electrical Resistance

    National Research Council Canada - National Science Library

    Soriano-Corral, F; Ramos-de Valle, L. F; Enríquez-Medrano, F. J; De León-Martínez, P. A; López-Quintanilla, M. L; Cabrera-Álvarez, E. N

    2012-01-01

      Nanocomposites of poly(methyl methacrylate-b-butyl acrylate)/multiwalled carbon nanotubes were prepared from different copolymers synthesized by RITP technique using iodine functionalized poly(methyl methacrylate...

  16. Degradable thiol-acrylate hydrogels as tunable matrices for three-dimensional hepatic culture.

    Science.gov (United States)

    Hao, Yiting; Lin, Chien-Chi

    2014-11-01

    A degradable poly(ethylene glycol)-diacrylate (PEGDA) hydrogel system was developed using simple macromer formulations and visible light initiated thiol-acrylate photopolymerization. In addition to PEGDA, other components in this gelation system include eosin-Y as a photo-sensitizer, bi-functional thiol (dithiothreitol, DTT) as a dual-purpose co-initiator and cross-linker, and N-vinylpyrrolidone (NVP) as a co-monomer. Gelation was achieved through a mixed-mode step-chain growth polymerization mechanism under bright visible light exposure. Increasing photo-sensitizer or NVP concentrations accelerated photo-crosslinking and increased final gel stiffness. Increasing bi-functional thiol content in the prepolymer solution only increased gel stiffness to some degree. As the concentration of thiol surpassed certain range, thiol-mediated chain-transfer events caused thiol-acrylate gels to form with lower degree of cross-linking. Pendant peptide, such as integrin ligand RGDS, was more effectively immobilized in the network via a thiol-acrylate reaction (using thiol-bearing peptide Ac-CRGDS. Underline indicates cross-linkable motif) than through homo-polymerization of acrylated peptide (e.g., acryl-RGDS). The incorporation of pendant peptide comes with the expense of a lower degree of gel cross-linking, which was rectified by increasing co-monomer NVP content. Without the use of any readily degradable macromer, these visible light initiated mixed-mode cross-linked hydrogels degraded hydrolytically due to the formation of thiol-ether-ester bonds following thiol-acrylate reactions. An exponential growth relationship was identified between the hydrolytic degradation rate and bifunctional thiol content in the prepolymer solution. Finally, we evaluated the cytocompatibility of these mixed-mode cross-linked degradable hydrogels using in situ encapsulation of hepatocellular carcinoma Huh7 cells. Encapsulated Huh7 cells remained alive and proliferated as time to form cell clusters

  17. The effectiveness of Nigella sativa seed extract in inhibiting Candida albicans on heat cured acrylic resin

    Directory of Open Access Journals (Sweden)

    Hanoem EH

    2011-09-01

    Full Text Available Background: Indonesia has a variety of plants that can be used for medicines. One of the medicinal plants is Nigella sativa. Nigella sativa has been used for medicinal purposes, both as medicinal herb and as medicinal oil. It contains saponin and atsiri oils that have antifungal, antimicrobial and antibacterial effects. Nigella sativa has been suggested as denture cleansers since it can inhibit the growth of Candida albicans (C. albicans on heat cured acrylic resin. Purpose: The aim of this research is to know the effectiveness of Nigella sativa seed extract in inhibiting the growth of C. albicans on heat cured acrylic resin. Methods: Eighteen acrylic samples were divided into three groups. Group I was control group, only contaminated with C. albicans without immersing in any solution. Group II was acrylic sample immersed in sterile aquades for one hour. Group III was acrylic sample immersed in Nigella sativa seed extract for one hour. Results: There were significant differences of C. albicans (p < 0.05 among the three groups. The number of Candida albicans was significantly higher in Group I, while that in group II was lower than that in group I, and that in group III was the lowest. Conclusion: Nigella sativa seed extract was effective in inhibiting the growth of C. albicans on heat cured acrylic resin.Latar belakang: Indonesia memiliki berbagai tanaman yang dapat dipakai sebagai obat, salah satu tanaman tersebut adalah jinten hitam (Nigella sativa. Pada beberapa negara jinten hitam telah digunakan untuk berbagai tujuan, baik sebagai obat herbal maupun sebagai minyak. kandungan jinten hitam adalah saponin dan minyak atsiri yang mempunyai efek anti jamur dan anti mikroba. Jinten hitam disarankan sebagai pilihan pembersih gigi tiruan yang dapat menghambat pertumbuhan Candida albicans (C. albicans pada resin akrilik heat cured. Tujuan: Tujuan penelitian ini adalah mengetahui efektivitas dari ekstrak biji jinten hitam dalam menghambat pertumbuhan

  18. Evaluation of home disinfection protocols for acrylic baseplates of removable orthodontic appliances: A randomized clinical investigation.

    Science.gov (United States)

    Peixoto, Iza Teixeira Alves; Enoki, Carla; Ito, Izabel Yoko; Matsumoto, Mirian Aiko Nakane; Nelson-Filho, Paulo

    2011-07-01

    In this randomized clinical trial, we investigated, using the microbial culture technique and scanning electron microscopy, the contamination of acrylic baseplates of removable orthodontic appliances by mutans streptococci (MS) and evaluated the efficacy of different home disinfection protocols with a 0.12% chlorhexidine gluconate spray (Periogard, Colgate-Palmolive, São Bernardo do Campo, Brazil). Fifteen dental students were randomly enrolled in a 3-stage changeover system with a 1-week interval between each stage. The acrylic baseplates were worn full time except at meals to simulate the routine use of removable appliances under clinical conditions. Three 1-week home disinfection protocols were tested in all stages by a different group of students: protocol I, toothbrushing + baseplate brushing + sterile tap water spraying once a day; protocol II, toothbrushing + baseplate brushing + Periogard spraying on the seventh day after appliance placement; and protocol III, toothbrushing + baseplate brushing + Periogard spraying on the fourth and seventh days after appliance placement. After the first week, the volunteers received new baseplates, toothbrushes, and dentifrices, and the regimens were repeated 2 more times. At the end of each week, the baseplates had a randomized disinfection protocol and were sent for microbiologic analysis. A scanning electron microscope was used to examine 3 acrylic baseplates representing each home protocol. The Friedman test (α = 0.05) compared the home protocols for the formation of MS colonies or biofilms on the acrylic surfaces. MS colonies or biofilms were found on all acrylic baseplates after protocol I. Protocols II and III reduced significantly (P 0.05) was observed between protocols II and III. The scanning electron microscope analysis confirmed the results of the microbiologic cultures. Disinfection of baseplates of removable orthodontic appliances by using 0.12% chlorhexidine spray once or twice a week reduced the

  19. Self-cleaning effects of acrylic resin containing fluoridated apatite-coated titanium dioxide.

    Science.gov (United States)

    Sawada, Tomofumi; Sawada, Tomoji; Kumasaka, Tomonari; Hamada, Nobushiro; Shibata, Takeshi; Nonami, Toru; Kimoto, Katsuhiko

    2014-03-01

    Specific materials when used in the manufacture of dentures can enhance the elimination of micro-organisms to promote oral hygiene. We used Candida albicans adhesion assays, methylene blue (MB)-decomposition tests and mechanical property tests to evaluate the photocatalytic properties of acrylic resin containing fluoridated apatite-coated titanium dioxide (FAp-TiO2 ) after treatment with ultraviolet A (UVA) irradiation. Conventional denture cleaning methods are unable to completely eliminate micro-organisms from dentures. Test specimens were prepared using acrylic resin containing three types of TiO2 powder [FAp-TiO2, titanium dioxide (TiO2 ) and hydroxyapatite-coated TiO2 (HAp-TiO2 )]; n = 96. In the adhesion assay, test specimens were incubated in a fungal suspension and subjected to UVA irradiation, and the number of attachments of C. albicans on the test specimens was counted. The MB-decomposition test and the three-point bending test were then performed to assess the photocatalytic effects of the FAp-TiO2 -containing acrylic resin. Fluoridated apatite-coated titanium dioxide-containing acrylic resin demonstrated superior effectiveness in inhibiting C. albicans adherence as well as in decomposing MB. In the three-point bending test, the resin showed a smaller decrease in flexural strength compared with TiO2 - or HAp-TiO2 -containing acrylic resin. Furthermore, UVA irradiation for 360 h did not significantly influence its flexural strength or elasticity modulus as compared with the control; this fulfils the requirements of International Organization for Standardization 1567:1999. Fluoridated apatite-coated titanium dioxide-containing acrylic resin is a clinically suitable material that promotes proper denture hygiene, particularly for elderly persons requiring nursing care or who have a decreased ability to perform normal activities of daily living. © 2013 John Wiley & Sons A/S and The Gerodontology Association. Published by John Wiley & Sons Ltd.

  20. Acoustic characteristics of clearly spoken English tense and lax vowels.

    Science.gov (United States)

    Leung, Keith K W; Jongman, Allard; Wang, Yue; Sereno, Joan A

    2016-07-01

    Clearly produced vowels exhibit longer duration and more extreme spectral properties than plain, conversational vowels. These features also characterize tense relative to lax vowels. This study explored the interaction of clear-speech and tensity effects by comparing clear and plain productions of three English tense-lax vowel pairs (/i-ɪ/, /ɑ-ʌ/, /u-ʊ/ in /kVd/ words). Both temporal and spectral acoustic features were examined, including vowel duration, vowel-to-word duration ratio, formant frequency, and dynamic spectral characteristics. Results revealed that the tense-lax vowel difference was generally enhanced in clear relative to plain speech, but clear-speech modifications for tense and lax vowels showed a trade-off in the use of temporal and spectral cues. While plain-to-clear vowel lengthening was greater for tense than lax vowels, clear-speech modifications in spectral change were larger for lax than tense vowels. Moreover, peripheral tense vowels showed more consistent clear-speech modifications in the temporal than spectral domain. Presumably, articulatory constraints limit the spectral variation of these extreme vowels, so clear-speech modifications resort to temporal features and reserve the primary spectral features for tensity contrasts. These findings suggest that clear-speech and tensity interactions involve compensatory modifications in different acoustic domains.