Tensile strength of ramie yarn (spinning by machine)/HDPE thermoplastic matrix composites

International Nuclear Information System (INIS)

Banowati, Lies; Hadi, Bambang K.; Suratman, Rochim; Faza, Aulia

2016-01-01

Technological developments should be trooped to prevent a gap between technology and environmental sustainability, then it needs to be developed “Green technology”. In this research is making of green composites which use natural fiber ramie as reinforcement. Whereas the matrix used was HDPE (High Density Polyethylene) thermoplastic polymer which could be recycled and had a good formability and flexibility. The ramie yarns and fibers for unidirectional (0°) direction respectively were mixed with HDPE powder and processed using hot compression molding. The surface morphology was observed by SEM (Scanning Electrone Microscopy). Results showed that both tensile strength of the ramie fiber/HDPE composites increased in comparison with the ramie yarn (spinning by machine)/HDPE composites. However, the ramie yarn (spinning by machine)/HDPE composites have a good producibility for wider application. Analysis of the test results using the Weibull distribution as approaches to modeling the reliability of the specimens.

Tensile strength of ramie yarn (spinning by machine)/HDPE thermoplastic matrix composites

Energy Technology Data Exchange (ETDEWEB)

Banowati, Lies, E-mail: liesbano@gmail.com; Hadi, Bambang K., E-mail: bkhadi@ae.itb.ac.id; Suratman, Rochim, E-mail: rochim@material.itb.ac.id; Faza, Aulia [Faculty of Mechanical and Aerospace Engineering, Bandung Institute of Technology, Indonesia Jl. Ganesha 10, Bandung (Indonesia)

2016-03-29

Technological developments should be trooped to prevent a gap between technology and environmental sustainability, then it needs to be developed “Green technology”. In this research is making of green composites which use natural fiber ramie as reinforcement. Whereas the matrix used was HDPE (High Density Polyethylene) thermoplastic polymer which could be recycled and had a good formability and flexibility. The ramie yarns and fibers for unidirectional (0°) direction respectively were mixed with HDPE powder and processed using hot compression molding. The surface morphology was observed by SEM (Scanning Electrone Microscopy). Results showed that both tensile strength of the ramie fiber/HDPE composites increased in comparison with the ramie yarn (spinning by machine)/HDPE composites. However, the ramie yarn (spinning by machine)/HDPE composites have a good producibility for wider application. Analysis of the test results using the Weibull distribution as approaches to modeling the reliability of the specimens.

RAMI analysis and modeling for the LANSCE accelerator systems

Energy Technology Data Exchange (ETDEWEB)

Macek, R.J.; Wilkinson, C.A. [Los Alamos National Laboratory, NM (United States)

1995-10-01

Reliability, availability, maintainability, and inspectability (RAMI) have become important issues for the high-power machines being planned for applications such as accelerator transmutation of nuclear waste (ATW), accelerator production of tritium (APT) and the next generation spallation neutron source. Beam reliability and beam availability are vitally important specifications to the present users of accelerator-driven spallation neutron sources, synchrotron light sources and medical accelerators. At Los Alamos, improved beam availability is a key goal in the planned LANSCE improvement program. Clearly, the capability to adequately model and predict the reliability and availability of complex accelerator systems will be of great value in assessing and optimizing RAMI measures in accelerator design and improvement programs. To date, no major accelerator project has developed comprehensive reliability models although the Advance Photon Source at ANL has started work on reliability analysis for selected subsystems. In this paper the authors discuss their experience in developing RAMI analysis and modeling for the LANSCE Accelerator Systems. Progress has been made in developing suitable measures and functions to characterize user risk, in logging of needed data on failure rates and repair/down times, and in developing a first-pass RAMI model for selected subsystems. Plans have been made for a more complete RAMI model. In addition, the authors discuss their experience in the use of probabilistic risk assessment (PRA) methodology for estimation of the reliability of active, instrumentation-based, radiation safety systems at LANSCE.

Progress in the RAMI analysis of a conceptual LHCD system for DEMO

Science.gov (United States)

Mirizzi, F.

2014-02-01

Reliability, Availability, Maintainability and Inspectability (RAMI) concepts and techniques, that acquired great importance during the first manned space missions, have been progressively extended to industrial, scientific and consumer equipments to assure them satisfactory performances and lifetimes. In the design of experimental facilities, like tokamaks, mainly aimed at demonstrating validity and feasibility of scientific theories, RAMI analysis has been often left aside. DEMO, the future prototype fusion reactors, will be instead designed for steadily delivering electrical energy to commercial grids, so that the RAMI aspects will assume an absolute relevance since their initial design phases. A preliminary RAMI analysis of the LHCD system for the conceptual EU DEMO reactor is given in the paper.

Progress in the RAMI analysis of a conceptual LHCD system for DEMO

International Nuclear Information System (INIS)

Mirizzi, F.

2014-01-01

Reliability, Availability, Maintainability and Inspectability (RAMI) concepts and techniques, that acquired great importance during the first manned space missions, have been progressively extended to industrial, scientific and consumer equipments to assure them satisfactory performances and lifetimes. In the design of experimental facilities, like tokamaks, mainly aimed at demonstrating validity and feasibility of scientific theories, RAMI analysis has been often left aside. DEMO, the future prototype fusion reactors, will be instead designed for steadily delivering electrical energy to commercial grids, so that the RAMI aspects will assume an absolute relevance since their initial design phases. A preliminary RAMI analysis of the LHCD system for the conceptual EU DEMO reactor is given in the paper

Transcriptome profiling using pyrosequencing shows genes associated with bast fiber development in ramie (Boehmeria nivea L.).

Science.gov (United States)

Chen, Jie; Pei, Zhihua; Dai, Lunjin; Wang, Bo; Liu, Lijun; An, Xia; Peng, Dingxiang

2014-10-22

Ramie (Boehmeria nivea L.), popularly known as "China grass", is one of the oldest crops in China and the second most important fiber crop in terms of area sown. Ramie fiber, extracted from the plant bast, is important in the textile industry. However, the molecular mechanism of ramie fiber development remains unknown. A whole sequencing run was performed on the 454 GS FLX + platform using four separately pooled parts of ramie bast. This generated 1,030,057 reads with an average length of 457 bp. Among the 58,369 unigenes (13,386 contigs and 44,983 isotigs) that were generated through de novo assembly, 780 were differentially expressed. As a result, 13 genes that belong to the cellulose synthase gene family (four), the expansin gene family (three) and the xyloglucan endotransglucosylase/hydrolase (XTH) gene family (six) were up-regulated in the top part of the bast, which was in contrast to the other three parts. The identification of these 13 concurrently up-regulated unigenes indicated that the early stage (represented by the top part of the bast) might be important for the molecular regulation of ramie fiber development. Further analysis indicated that four of the 13 unigenes from the expansin (two) and XTH (two) families shared a coincident expression pattern during the whole growth season, which implied they were more relevant to ramie fiber development (fiber quality, etc.) during the different seasons than the other genes. To the best of our knowledge, this study is the first to characterize ramie fiber development at different developmental stages. The identified transcripts will improve our understanding of the molecular mechanisms involved in ramie fiber development. Moreover, the identified differentially expressed genes will accelerate molecular research on ramie fiber growth and the breeding of ramie with better fiber yields and quality.

A novel nano-nonwoven fabric with three-dimensionally dispersed nanofibers: entrapment of carbon nanofibers within nonwovens using the wet-lay process

International Nuclear Information System (INIS)

Karwa, Amogh N; Davis, Virginia A; Tatarchuk, Bruce J; Barron, Troy J

2012-01-01

This study demonstrates, for the first time, the manufacturing of novel nano-nonwovens that are comprised of three-dimensionally distributed carbon nanofibers within the matrices of traditional wet-laid nonwovens. The preparation of these nano-nonwovens involves dispersing and flocking carbon nanofibers, and optimizing colloidal chemistry during wet-lay formation. The distribution of nanofibers within the nano-nonwoven was verified using polydispersed aerosol filtration testing, air permeability, low surface tension liquid capillary porometry, SEM and cyclic voltammetry. All these characterization techniques indicated that nanofiber flocks did not behave as large solid clumps, but retained the ‘nanoporous’ structure expected from nanofibers. These nano-nonwovens showed significant enhancements in aerosol filtration performance. The reduction–oxidation reactions of the functional groups on nanofibers and the linear variation of electric double-layer capacitance with nanofiber loading were measured using cyclic voltammetry. More than 65 m 2 (700 ft 2 ) of the composite were made during the demonstration of process scalability using a Fourdrinier-type continuous pilot papermaking machine. The scalability of the process with the control over pore size distribution makes these composites very promising for filtration and other nonwoven applications. (paper)

Ramie (Boehmeria nivea)'s uranium bioconcentration and tolerance attributes.

Science.gov (United States)

Wang, Wei-Hong; Luo, Xue-Gang; Liu, Lai; Zhang, Yan; Zhao, Hao-Zhou

2018-04-01

The authors sampled and analyzed 15 species of dominant wild plants in Huanan uranium tailings pond in China, whose tailings' uranium contents were 3.21-120.52 μg/g. Among the 15 species of wild plants, ramie (Boehmeria nivea) had the strongest uranium bioconcentration and transfer capacities. In order to study the uranium bioconcentration and tolerance attributes of ramie in detail, and provide a reference for the screening remediation plants to phytoremedy on a large scale in uranium tailings pond, a ramie cultivar Xiangzhu No. 7 pot experiment was carried out. We found that both wild ramie and Xiangzhu No. 7 could bioconcentrate uranium, but there were two differences. One was wild ramie's shoots bioconcentrated uranium up to 20 μg/g (which can be regarded as the critical content value of the shoot of uranium hyperaccumulator) even the soil uranium content was as low as 5.874 μg/g while Xiangzhu No. 7's shoots could reach 20 μg/g only when the uranium treatment concentrations were 275 μg/g or more; the other was that all the transfer factors of 3 wild samples were >1, and the transfer factors of 27 out of 28 pot experiment samples were uranium hyperaccumulator. Xiangzhu No. 7 satisfied the needs of uranium hyperaccumulator on accumulation capability, tolerance capability, bioconcentration factor, but not transfer capability, so Xiangzhu No. 7 was not a uranium hyperaccumulator. We analyzed the possible reasons why there were differences in the uranium bioconcentration and transfer attributes between wild ramie and Xiangzhu No. 7., and proposed the direction for further research. In our opinion, both the plants which bioconcentrate contaminants in the shoots and roots can act as phytoextractors. Although Xiangzhu No. 7's biomass and accumulation of uranium were concentrated on the roots, the roots were small in volume and easy to harvest. And Xiangzhu No. 7's cultivating skills and protection measures had been developed very well. Xiangzhu No. 7's

Preliminary RAMI analysis of WCLL blanket and breeder systems

International Nuclear Information System (INIS)

Arroyo, Jose Manuel; Brown, Richard; Harman, Jon; Rosa, Elena; Ibarra, Angel

2015-01-01

Highlights: • Preliminary RAMI model for WCLL has been developed. • Critical parts and parameters influencing WCLL availability have been focused. • Necessary developments of tools/models to represent system performance have been identified. - Abstract: DEMO will be a prototype fusion reactor designed to prove the capability to produce electrical power in a commercially acceptable way. One of the key factors in that endeavor is the achievement of certain level of plant availability. Therefore, RAMI (Reliability, Availability, Maintainability and Inspectability) will be a key element in the engineering development of DEMO. Some studies have been started so as to develop the tools and models to assess different design alternatives from RAMI point of view. The main objective of these studies is to be able to evaluate the influence of different parameters on DEMO availability and to focus the critical parts that should be further researched and improved in order to develop a high-availability oriented DEMO design. A preliminary RAMI analysis of the Water Cooled Lithium-Lead (WCLL) blanket and breeder concept for DEMO has been developed. The amounts of single elements that may fail (e.g. more than 180,000 C-shaped tubes) and the mean down time associated to failures inside the vacuum vessel (around 3 months) have been highlighted as the critical parameters influencing the system availability. On the other hand, the necessary developments of tools/models to better represent the system performance have been identified and proposed for future work.

Preliminary RAMI analysis of WCLL blanket and breeder systems

Energy Technology Data Exchange (ETDEWEB)

Arroyo, Jose Manuel, E-mail: josemanuel.arroyo@ciemat.es [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain); Brown, Richard [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon (United Kingdom); Harman, Jon [EFDA Close Support Unit, Garching (Germany); Rosa, Elena; Ibarra, Angel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain)

2015-10-15

Highlights: • Preliminary RAMI model for WCLL has been developed. • Critical parts and parameters influencing WCLL availability have been focused. • Necessary developments of tools/models to represent system performance have been identified. - Abstract: DEMO will be a prototype fusion reactor designed to prove the capability to produce electrical power in a commercially acceptable way. One of the key factors in that endeavor is the achievement of certain level of plant availability. Therefore, RAMI (Reliability, Availability, Maintainability and Inspectability) will be a key element in the engineering development of DEMO. Some studies have been started so as to develop the tools and models to assess different design alternatives from RAMI point of view. The main objective of these studies is to be able to evaluate the influence of different parameters on DEMO availability and to focus the critical parts that should be further researched and improved in order to develop a high-availability oriented DEMO design. A preliminary RAMI analysis of the Water Cooled Lithium-Lead (WCLL) blanket and breeder concept for DEMO has been developed. The amounts of single elements that may fail (e.g. more than 180,000 C-shaped tubes) and the mean down time associated to failures inside the vacuum vessel (around 3 months) have been highlighted as the critical parameters influencing the system availability. On the other hand, the necessary developments of tools/models to better represent the system performance have been identified and proposed for future work.

Mechanical properties of ramie fiber reinforced epoxy lamina composite for socket prosthesis

Directory of Open Access Journals (Sweden)

Tresna Soemardi

2010-10-01

Full Text Available This paper presents an investigation into the application of natural fiber composite especially ramie fiber reinforced epoxy lamina composite for socket prosthesis. The research focuses on the tensile and shear strength from ramie fiber reinforced epoxy lamina composite which will be applied as alternative material for socket prosthesis. The research based on American Society for Testing Material (ASTM standard D 3039/D 3039M for tensile strength and ASTM D 4255/D 4255M-83 for shear strength. The ramie fiber applied is a fiber continue 100 % Ne14'S with Epoxy Resin Bakelite EPR 174 as matrix and Epoxy Hardener V-140 as hardener. The sample composite test made by hand lay up method. Multiaxial characteristic from ramie fiber reinforced epoxy composite will be compared with ISO standard for plastic/polymer for health application and refers strength of material application at Prosthetics and Orthotics. The analysis was completed with the mode of the failure and the failure criterion observation by using Scanning Electron Microscope (SEM. Based on results of the research could be concluded that ramie fiber reinforced epoxy composite could be developed further as the alternative material for socket prosthesis on Vf 40-50%. Results of the research will be discussed in more detail in this paper.

Non-Wovens as Sound Reducers

Science.gov (United States)

Belakova, D.; Seile, A.; Kukle, S.; Plamus, T.

2018-04-01

Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

Development of a RAMI model for LANSCE and high power APT accelerators

International Nuclear Information System (INIS)

Tallerico, P.J.

1994-01-01

Assessment of the reliability, availability, maintainability and inspectability (RAMI) of all high power, high cost systems is important to justify and improve the cost effectiveness of these systems. For the very large (over 100 MW) accelerator systems associated with APT, a RAMI model is very valuable in guiding the design and allocation of resources. A RAMI model of an existing machine is also valuable, since machine improvement funds must be allocated to increase the availability by the largest amount. The authors have developed a RAMI model using the critical subsystems of the LANSCE accelerator and beam delivery complex as an example and to evaluate the effectiveness for estimating reliability and beam availability. LAMPF and LANSCE together provide most of the features required for the accelerator and beam delivery part of a high-power APT machine, but LANSCE is pulsed, rather than CW. This complex is capable of a 1-MW average power H - beam, and it is the most powerful proton accelerator in the US built to date

Preparation and Characterization of Polyurethane-Polydimethylsiloxane/Polyamide12-b-Polytetramethylene Glycol Blend Membranes for Gas Separation

Directory of Open Access Journals (Sweden)

Mohammad Ali Semsarzadeh*

2013-07-01

Full Text Available Blend membranes of synthesized polyurethane based on toluene diisocyanate (TDI, polydimethylsiloxane (PDMS and polytetramethylene glycol (PTMG with polyamide12-b-PTMG were prepared by solution casting technique. The synthesized polyurethane-polydimethylsiloxane and PU-PDMS/polyamide12-b-PTMG blend membranes were characterized by Fourier transform infrared spectroscopy (FTIR, differential scanning calorimetry (DSC and scanning electron microscopy (SEM. In the FTIR spectrum of the synthesized PU-PDMS, the disappearance of NCO stretching vibration at 2270 cm−1 was used to confirm the completion of the reaction. According to our DSC results, the use of higher polyamide12-b-PTMG content in PU-PDMS/polyamide12-b-PTMG blends led to greater compatibility between the two phases. The SEM images showed that the blends with polyamide12-b-PTMG (20 wt% were significantly more homogeneous in the micrometric scale compared to other samples. Gas transport properties have been determined for N2, CO2 and He gases and the obtained permeability values were correlated with the properties of the blends. The comparison of the results with that of the pure PU-PDMS membrane showed that the blend membranes had a higher permeability toward CO2 and lower toward N2 gas. The blend membrane with 20 wt% polyamide12-b-PTMG showed higher CO2 permeability (≈105 Barrer compared to PU-PDMS membrane. By introduction of polyamide12-b-PTMG into PU-PDMS matrix a perceptible rise in helium ideal selectivity of the blend membranes was observed. In blend membranes with 5-20 wt% polyamide12-b-PTMG contents, an enhancement of CO2/N2 (244%, He/N2 (20% and CO2/He (103% selectivity factor was observed. The experimental permeability values of the blend membranes were compared with the calculated permeability based on a modified additive logarithmic model.

Results of the RAMI analyses performed for the IFMIF accelerator facility in the engineering design phase

Energy Technology Data Exchange (ETDEWEB)

Bargalló, Enric, E-mail: enric.bargallo@esss.se [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Arroyo, Jose Manuel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain); Abal, Javier; Dies, Javier; De Blas, Alfredo; Tapia, Carlos [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Moya, Joaquin; Ibarra, Angel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain)

2015-10-15

Highlights: • RAMI methodology used for IFMIF accelerator facility is presented. • Availability analyses and results are shown. • Main accelerator design changes are proposed. • Consequences and conclusions of the RAMI analyses are described. - Abstract: This paper presents a summary of the RAMI (Reliability Availability Maintainability Inspectability) analyses done for the IFMIF (International Fusion Materials Irradiation Facility) Accelerator facility in the Engineering Design Phase. The methodology followed, the analyses performed, the results obtained and the conclusions drawn are described. Moreover, the consequences of the incorporation of the RAMI studies in the IFMIF design are presented and the main outcomes of these analyses are shown.

Results of the RAMI analyses performed for the IFMIF accelerator facility in the engineering design phase

International Nuclear Information System (INIS)

Bargalló, Enric; Arroyo, Jose Manuel; Abal, Javier; Dies, Javier; De Blas, Alfredo; Tapia, Carlos; Moya, Joaquin; Ibarra, Angel

2015-01-01

Highlights: • RAMI methodology used for IFMIF accelerator facility is presented. • Availability analyses and results are shown. • Main accelerator design changes are proposed. • Consequences and conclusions of the RAMI analyses are described. - Abstract: This paper presents a summary of the RAMI (Reliability Availability Maintainability Inspectability) analyses done for the IFMIF (International Fusion Materials Irradiation Facility) Accelerator facility in the Engineering Design Phase. The methodology followed, the analyses performed, the results obtained and the conclusions drawn are described. Moreover, the consequences of the incorporation of the RAMI studies in the IFMIF design are presented and the main outcomes of these analyses are shown.

Influence of fiber surface-treatment on interfacial property of poly(L-lactic acid)/ramie fabric biocomposites under UV-irradiation hydrothermal aging

Energy Technology Data Exchange (ETDEWEB)

Chen Dakai; Li Jing [Institute of Nano- and Bio-polymeric Materials, School of Material Science and Engineering, Tongji University, Shanghai 200092 (China); Ren Jie, E-mail: renjie6598@163.com [Institute of Nano- and Bio-polymeric Materials, School of Material Science and Engineering, Tongji University, Shanghai 200092 (China) and Key Laboratory of Advanced Civil Engineering Materials, Ministry of Education, Tongji University, Shanghai 200092 (China)

2011-04-15

Research highlights: {yields} Ramie fiber is used as reinforced material because it's lowest water absorption among sisal, jute, kenaf and ramie fiber. {yields} Fiber surface-treatment can cause an accelerated decline in mechanical properties of PLLA biocomposites after UV-irradiation hydrothermal aging. {yields} The swelling of ramie fibers reduce the interfacial adhesive strength in critical area of PLLA matrix-ramie fabric interface. - Abstract: The present study is devoted to the effect of fiber surface-treatment on the interfacial property of biocomposites based on poly(L-lactic acid) (PLLA) and ramie fabric. Ramie fiber is used as reinforced material because it's lowest water absorption among sisal, jute, kenaf and ramie fiber. Fiber surface-treatment can increase the water absorption of natural fibers. SEM images show that PLLA biocomposites with treated ramie fabric exhibit better interfacial adhesion character. DMA results show that the storage modulus of PLLA biocomposites with treated ramie increase compared to neat PLLA and PLLA biocomposites with untreated ramie. Unexpectedly, fiber surface-treatment can cause an accelerated decline in mechanical properties of PLLA biocomposites after UV-irradiation hydrothermal aging. Finally, GPC results show that there is no obvious decline in the molecular weight of PLLA. The main reason for this decline is the interfacial destructive effect induced by the water absorption of ramie fiber.

Effect of atmospheric pressure plasma treatment condition on adhesion of ramie fibers to polypropylene for composite

Energy Technology Data Exchange (ETDEWEB)

Li, Ying [College of Material and Textile Engineering, Jiaxing University, Jiaxing 314033 (China); Center for Plasma-Aided Manufacturing, Madison, WI 53706 (United States); School of Human Ecology, University of Wisconsin-Madison, Madison, WI 53706 (United States); Manolache, Sorin [Center for Plasma-Aided Manufacturing, Madison, WI 53706 (United States); US Forest Products Laboratory, Madison, WI 53726 (United States); Qiu, Yiping, E-mail: ypqiu@dhu.edu.cn [College of Textiles, Donghua University, Shanghai 201620 (China); Sarmadi, Majid, E-mail: majidsar@wisc.edu [Center for Plasma-Aided Manufacturing, Madison, WI 53706 (United States); School of Human Ecology, University of Wisconsin-Madison, Madison, WI 53706 (United States); Materials Science Program, University of Wisconsin-Madison, Madison, WI 53706 (United States)

2016-02-28

Graphical abstract: - Highlights: • The continuous ethanol flow technique can successfully modify ramie fiber surface with an increase in IFSS value up to 50%. • Response surface methodology was applied to design the plasma treatment parameters for ramie fiber modification. • The ethanol flow rate was the most influential treatment parameter in plasma modification process. - Abstract: In order to improve the interfacial adhesion between hydrophilic ramie fibers and hydrophobic polypropylene (PP) matrices, ramie fibers are modified by atmospheric pressure dielectric barrier discharge (DBD) plasma with our continuous ethanol flow technique in helium environment. A central composite design of experiments with different plasma processing parameter combinations (treatment current, treatment time and ethanol flow rate) is applied to find the most influential parameter and to obtain the best modification effect. Field emission scanning electron microscope (SEM) shows the roughened surfaces of ramie fibers from the treated groups due to plasma etching effect. Dynamic contact angle analysis (DCAA) demonstrates that the wettability of the treated fibers drastically decreases. Microbond pullout test shows that the interfacial shear strength (IFSS) between treated ramie fibers and PP matrices increases significantly. Residual gas analysis (RGA) confirms the creation of ethyl groups during plasma treatment. This study shows that our continuous ethanol flow technique is effective in the plasma modification process, during which the ethanol flow rate is the most influential parameter but all parameters have simultaneous influence on plasma modification effect of ramie fibers.

Production and characterization of composites based on ramie cellulose micro fibers filler

International Nuclear Information System (INIS)

Edi Syafri; Anwar Kasim and Alfi Asben; Hairul Abral; Sudirman

2018-01-01

This research studied production and characterization of bioplastic composites by using cellulose fibers (Cellulose Micro Fibers/CMF) as reinforcement in tapioca starch. CMF ramie was produced by using milling method (CMFM) and ultrasonication (CMFU) with particle size 3,51 μm and 0,388 μm, respectively. The fabrication of the bioplastic composites was performed by solution casting with addition glycerol as a plasticizer. SEM, UTM, XRD, and DSC characterization were carried out. The results show that the size and concentration of CMF significantly affect the physical bioplastic composites. The SEM displays the good interaction CMF filler with the tapioca starch matrix, where the small sized hemophytic CMF bioplastic exhibits are more homogeneous compact and surface structure. The optimum value of tensile strength is found in the addition of 8 % (w/w)CMF ramie from ultrasonication and milling results increased from 1.64 MPa to 3.31 MPa and 2.71 MPa, respectively. The thermal properties have low significant effect with addition ramie CMF.X-ray Diffraction Analysis (XRD) showed that the crystallinity of bioplastic composites increased with the addition of ramie CMF from 8.65 % to 20.21 % for CMFM and 15.12 % for CMFU. (author)

Constitutional tolerance to heavy metals of a fiber crop, ramie (Boehmeria nivea), and its potential usage

Energy Technology Data Exchange (ETDEWEB)

Yang, B.; Zhou, M.; Shu, W.S.; Lan, C.Y. [State Key Laboratory of Biocontrol, and School of Life Sciences, Sun Yat-sen (Zhongshan) University, Guangzhou 510275 (China); Ye, Z.H., E-mail: lssyzhh@mail.sysu.edu.c [State Key Laboratory of Biocontrol, and School of Life Sciences, Sun Yat-sen (Zhongshan) University, Guangzhou 510275 (China); Qiu, R.L. [Guangdong Provincial Key Lab of Environmental Pollution Control and Remediation Technology, and School of Sciences and Engineering, Sun Yat-sen (Zhongshan) University, Guangzhou 510275 (China); Jie, Y.C. [Institute of Bast Fiber Crops, Chinese Academy of Agricultural Sciences, Changsha 410205 (China); Cui, G.X. [Ramie Research Institute, Hunan Agricultural University, Changsha 410128 (China); Wong, M.H., E-mail: mhwong@hkbu.edu.h [Croucher Institute for Environmental Sciences, and Department of Biology, Hong Kong Baptist University, Kowloon Tong (Hong Kong)

2010-02-15

It is observed that ramie (Boehmeria nivea), an economic fiber crop, can establish and colonize metal-contaminated sites in China. Metal tolerance and accumulation by ramie originating from 13 metal-contaminated and 4 'clean' sites in China were compared under field and hydroponic conditions. All selected populations and germplasms displayed good growth performance under diverse metal-contaminated habitats; while growth responses, metal accumulation and tolerance were similar among the 8 populations and 2 germplasms when exposed to solutions containing elevated As, Cd, Pb, or Zn in the laboratory. These revealed that ramie possesses a certain degree of constitutional metal tolerance. To our knowledge, this is the first report of constitutional metal tolerance possessed by a fiber crop. Ramie can be considered as a good candidate for both fiber production and phytoremediation of sites contaminated by multi-metals, as it accumulates relative low metal concentrations, but possesses both high biomass and high economic value. - Ramie possesses economic and environmental values in phytoremediation

Energy transfer mechanism in the hydroentaglement nonwoven process

CSIR Research Space (South Africa)

Moyo, D

2010-09-01

Full Text Available for Parliamentary grant funding and MsM Polymer and composites competence Area for studentship support. refereNces 1. www.edana.org 2. cary, N. c. 1998. The Nonwoven fabrics Handbook, Association of the Nonwoven fabrics industry. 2-10. 3. russell, s. j. 2007...

Oil sorption and retention capacities of thermally-bonded hybrid nonwovens prepared from cotton, kapok, milkweed and polypropylene fibers.

Science.gov (United States)

Thilagavathi, G; Praba Karan, C; Das, Dipayan

2018-08-01

This work reports on a series of thermally-bonded, hybrid and oil-sorbent nonwovens developed from binary and tertiary mixing of cotton, kapok, and three varieties of milkweed fibers (Asclepias Syriaca, Calotropis Procera and Calotropis Gigantea) and polypropylene fibers. The physical and chemical properties of the fibers were investigated to examine their oleophilic character. It was observed that all the fiber surfaces were covered with natural wax. Further, kapok and milkweed fibers were found to have less cell wall thickness and high void ratio. Oil sorption and retention characteristics of these fibers were studied in loose fibrous form as well as in structured assembly form (thermally-bonded nonwovens) using high density oil and diesel oil. The effects of fiber diameter, fiber cross-sectional shape, fiber surface area and porosity on the oil sorption behavior were discussed. An excellent and a selective oil sorption behavior of milkweed fibers (Calotropis Procera and Calotropis Gigantea) blended with cotton and polypropylene fibers were observed. The maximum oil sorption capacity of the developed thermal bonded nonwoven was 40.16 g/g for high density (HD) oil and 23.00 g/g for diesel oil. Further, a high porosity combined with high surface area played a major role in deciding the oil sorption and retention characteristics. Copyright © 2018 Elsevier Ltd. All rights reserved.

Three Point Bending of Top-Hat Stiffened Chopped Short Fibre Ramie/HDPE Thermoplastic Composite Beam

Science.gov (United States)

Hadi, Bambang K.; Nuril, Yogie S.

2018-04-01

The use of natural fibre and thermoplastic matrices in composite materials increased significantly during the last decade especially in the automotive industries. Ramie is one of these potential natural fibres. In this paper, a three point bending of top-hat beam made of ramie/HDPE (High-Density-Polyethylene) composites was performed. Top-hat stiffened structures were common structures found in the aerospace industries. Nevertheless, these structures are beginning to be applied in automotive structures in the forms of chassis and bumpers. The ramie/HDPE composite was manufactured using hot-press technique. The temperature was set to be 135°C and the pressure was 6 bars. Chopped short ramie fibre was used, due to good drape ability characteristics. The experiments showed that the beams produced a large non-linearity. Linear Finite Element Analysis was carried out to be compared with the experimental data. The differences are reasonable.

Developing antiviral surgical gown using nonwoven fabrics for ...

African Journals Online (AJOL)

Objectives: To develop antiviral surgical gown comprising of Polypropylene nonwoven as outer layer, Polytetrafluroethylene (PTFE) film as middle layer and polyester nonwoven as inner layer and the surgical gown with a basic weight of 70 g/m2. Methods: The titanium dioxide (TiO2) nano dispersion was prepared with ...

Evolution of Emergent Technologies for Producing Nonwoven Fabrics for Air Filtration

Science.gov (United States)

Ou, Yingjie

2016-01-01

Nonwovens is a fast growing industry driven by technological research and development (R&D), and one of the major application areas for nonwovens is air filtration. Research on nonwovens technologies has mainly focused on the science and technology areas, but there is very little published research on technology management issues within the…

RAMI strategies in the IFMIF Test Facilities design

Energy Technology Data Exchange (ETDEWEB)

Abal, Javier, E-mail: javier.abal@upc.edu [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Dies, Javier [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Arroyo, José Manuel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, 28040 Madrid (Spain); Bargalló, Enric [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Casal, Natalia; García, Ángela [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, 28040 Madrid (Spain); Martínez, Gonzalo; Tapia, Carlos; De Blas, Alfredo [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Mollá, Joaquín; Ibarra, Ángel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, 28040 Madrid (Spain)

2013-10-15

Highlights: • We have implemented fault tolerant design strategies so that the strong availability requirements are met. • The evolution to the present design of the signal and cooling lines inside the TTC has also been compared. • The RAMI analyses have demonstrated a strong capability in being a complementary tool in the design of IFMIF Test Facilities. -- Abstract: In this paper, a RAMI analysis of the different stages in Test Facilities (TF) design is described. The comparison between the availability results has been a milestone not only to evaluate the major unavailability contributors in the updates but also to implement fault tolerant design strategies when possible. These strategies encompass a wide range of design activities: from the definition of degraded modes of operation in the Test Facilities to specific modifications in the test modules in order to guarantee their fail safe operation.

RAMI strategies in the IFMIF Test Facilities design

International Nuclear Information System (INIS)

Abal, Javier; Dies, Javier; Arroyo, José Manuel; Bargalló, Enric; Casal, Natalia; García, Ángela; Martínez, Gonzalo; Tapia, Carlos; De Blas, Alfredo; Mollá, Joaquín; Ibarra, Ángel

2013-01-01

Highlights: • We have implemented fault tolerant design strategies so that the strong availability requirements are met. • The evolution to the present design of the signal and cooling lines inside the TTC has also been compared. • The RAMI analyses have demonstrated a strong capability in being a complementary tool in the design of IFMIF Test Facilities. -- Abstract: In this paper, a RAMI analysis of the different stages in Test Facilities (TF) design is described. The comparison between the availability results has been a milestone not only to evaluate the major unavailability contributors in the updates but also to implement fault tolerant design strategies when possible. These strategies encompass a wide range of design activities: from the definition of degraded modes of operation in the Test Facilities to specific modifications in the test modules in order to guarantee their fail safe operation

Identification of drought, cadmium and root-lesion nematode infection stress-responsive transcription factors in ramie

Directory of Open Access Journals (Sweden)

Zheng Xia

2016-01-01

Full Text Available Drought, cadmium (Cd stress, and root lesion nematode (RLN infection are three of the most important stresses affecting ramie growth and development; therefore, ramie breeding programs focus on their management more than on any other abiotic or biotic stresses. The fact that only a small number of stress-responsive transcription factors (TFs have been identified so far is a major obstacle in the elucidation of mechanisms regulating the response to these three stresses in ramie. In this study, in order to uncover more stress-responsive TFs, a total of 179 nonredundant genes with full-length open reading frames from the MYB, AP2/ERF, bZIP, HD-ZIP, and COL families were obtained by searching for against the ramie transcriptome. Expression pattern analysis demonstrated that most of these genes showed relatively higher expression in the stem xylem and bast than in other tissues. Among these genes, 96 genes were found to be involved in responses to drought, Cd exposure, or RLN-infection. The expression of 54 of these genes was regulated by at least two stresses. These stress-responsive TFs probably have roles in the regulation of stress tolerance. The discovery of these stress-responsive TFs will be helpful for furthering our understanding of the mechanisms that regulate stress responses in ramie.

Development of hemp fibre - PP nonwoven composites - Conference Paper

CSIR Research Space (South Africa)

Hargitai, H

2005-09-01

Full Text Available Non-woven mats from hemp and polypropylene fibres in various proportions were produced and hot pressed to make composite material. The effect of hemp fibre content and anisotropy in non-woven mats resulting from the carding technology were examined...

Plastik nonwoven sebagai pengemas bahan makanan yang bersifat breathable

Directory of Open Access Journals (Sweden)

Penny Setyowati

2003-06-01

Full Text Available Abstract Nonwoven plastic is a new material for packaging that has some special quality among the other things such as flexible, higher strength, hydrophob, breathable and hygienes. The technology of nonwoven plastic is spunbond technolog which is a clean technology and produce a non fibre product. The raw material of nonwoven plastic is food grade polypropylene, so that the products are safe for food packaging. Recently just pioneered of nonwoven plastic application as innerliner of plastic sack that can replace “karung goni”as rice packaging and replace cotton sack as meal or flour packaging. Therefore grains that have not been prepared yet, respiration activity is very important to be breathable characteristic of nonwoven plastic is able to support air circulation very well and also to keep humidity balance in the packaging. At the flour packaging, beside hydrophob characteristic, however breathable characteristic is necessary too because flour has a tendency to absorb water and flour stability must be kept at 13.5 – 14% moisture content. The first experiment was taken by PT. Boma Internusa concerning with rice storage that use nonwoven plastic packaging as innerliner of plastic sack during 2 months, and analysis showed that the rice did not smell, louse unfolding was decrease 9fumigation cost was low, yellow grains and broken grains were decrease and did not occur any change of color. In the experiment of flour storage during 3 months gave an analysis that flour wsa still having good condition and fulfilled the standard trade

RAMI analysis for ITER radial X-ray camera system

Energy Technology Data Exchange (ETDEWEB)

Qin, Shijun, E-mail: sjqin@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Hu, Liqun; Chen, Kaiyun [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Barnsley, Robin; Sirinelli, Antoine [ITER Organization, Route Vinon sur Verdon, CS 90046, 13067, St. Paul lez Durance, Cedex (France); Song, Yuntao; Lu, Kun; Yao, Damao; Chen, Yebin; Li, Shi; Cao, Hongrui; Yu, Hong; Sheng, Xiuli [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2016-11-15

Highlights: • The functional analysis of the ITER RXC system was performed. • A failure modes, effects and criticality analysis of the ITER RXC system was performed. • The reliability and availability of the ITER RXC system and its main functions were calculated. • The ITER RAMI approach was applied to the ITER RXC system for technical risk control in the preliminary design phase. - Abstract: ITER is the first international experimental nuclear fusion device. In the project, the RAMI approach (reliability, availability, maintainability and inspectability) has been adopted for technical risk control to mitigate all the possible failure of components in preparation for operation and maintenance. RAMI analysis of the ITER Radial X-ray Camera diagnostic (RXC) system during preliminary design phase was required, which insures the system with a very high performance to measure the X-ray emission and research the MHD of plasma with high accuracy on the ITER machine. A functional breakdown was prepared in a bottom-up approach, resulting in the system being divided into 3 main functions, 6 intermediate functions and 28 basic functions which are described using the IDEFØ method. Reliability block diagrams (RBDs) were prepared to calculate the reliability and availability of each function under assumption of operating conditions and failure data. Initial and expected scenarios were analyzed to define risk-mitigation actions. The initial availability of RXC system was 92.93%, while after optimization the expected availability was 95.23% over 11,520 h (approx. 16 months) which corresponds to ITER typical operation cycle. A Failure Modes, Effects and Criticality Analysis (FMECA) was performed to the system initial risk. Criticality charts highlight the risks of the different failure modes with regard to the probability of their occurrence and impact on operations. There are 28 risks for the initial state, including 8 major risks. No major risk remains after taking into

Time-Dependent Antimicrobial Activity of Filtering Nonwovens with Gemini Surfactant-Based Biocides

Directory of Open Access Journals (Sweden)

Katarzyna Majchrzycka

2017-09-01

Full Text Available Previous studies on nonwovens used for respiratory protective devices (RPDs were related to equipment intended for short-term use. There is only limited research on the development of biocidal nonwoven fabrics for reusable RPDs that could be used safely in an industrial work environment where there is a risk of microbial growth. Moreover, a new group of biocides with high antimicrobial activity—gemini surfactants, has never been explored for textile’s application in previous studies. The aim of this study was to develop high-efficiency melt-blown nonwovens containing gemini surfactants with time-dependent biocidal activity, and to validate their antimicrobial properties under conditions simulating their use at a plant biomass-processing unit. A set of porous biocidal structures (SPBS was prepared and applied to the melt-blown polypropylene (PP nonwovens. The biocidal properties of the structures were triggered by humidity and had different activation rates. Scanning electron microscopy was used to undertake structural studies of the modified PP/SPBS nonwovens. In addition, simulation of plant biomass dust deposition on the nonwovens was performed. The biocidal activity of PP/SPBS nonwovens was evaluated following incubation with Escherichia coli and Aspergillus niger from the American Type Culture Collection, and with Pseudomonas fluorescens and Penicillium chrysogenum isolated from the biomass. PP/SPBS nonwovens exhibited antimicrobial activity to varying levels. Higher antimicrobial activity was noted for bacteria (R = 87.85–97.46% and lower for moulds (R = 80.11–94.53%.

Surface Treatment of PET Nonwovens with Atmospheric Plasma

International Nuclear Information System (INIS)

Li Shufang

2013-01-01

In this study, polyethylene-terephthalate (PET) nonwovens are treated using an atmospheric plasma and the effects of the treatment time, treatment power and discharge distance on the ability of water-penetration into the nonwovens are investigated. The result indicates that the method can improve the wettability of PET nonwovens remarkably, but the aging decay of the sample's wettability is found to be notable as a function of the storage time after treatment due to the internal rotation of the single bond of surface macromolecules. As shown by SEM and XPS analysis, the etching and surface reaction are significant, and water-penetration weight is found to increase remarkably with the increasing power. This variation can be attributed to momentum transfer and enhanced higher-energy particle excitation.

Genetic structure and relationships of an associated population in ramie (Boehmeria nivea L. Gaud evaluated by SSR markers

Directory of Open Access Journals (Sweden)

Siyuan Zhu

2017-01-01

Full Text Available Ramie (Boehmeria nivea L. Gaud is one of the most important natural fibre crops. For enhanced crop development, it is necessary to understand its population structure and genetic relationships. In this study, we assessed the genetic diversity and population structure of 134 ramie accessions (with three plants per accession from 12 regions by using 36 simple sequence repeat markers. The 36 microsatellite primers revealed 149 alleles in 134 ramie populations, with an average of 4.14 alleles per locus. The structure analysis divided the 134 ramie accessions into three groups (I, II and III, and into further six subgroups (a, b, c, d, e and f. In Subgroup b, 13 accessions were from Guizhou Province, 9 accessions were from Sichuan Province and the remaining 20 accessions were from Chongqing (4, Hunan (8, Guangxi (4, Jiangxi (2, Yunan (1 and Taiwan (1. In Subgroup d, 22 accessions were from Guizhou Province and the remaining 17 accessions were from Chongqing (6, Sichuan (5 and Yunnan (6. It can be inferred that the genetic background of these ramie accessions did not always correlate with their geographical regions. Similar results were found in Subgroups a and f. The pair-wise genetic similarity coefficients between the 134 accessions ranged from 0.390 to 0.939, which suggested that there was abundant genetic diversity in the ramie accessions. These markers have provided important information about the genetic structure of ramie, which can contribute to future breeding and improvement programmes for these resources.

Tensile and Flexural Properties of Cement Composites Reinforced with Flax Nonwoven Fabrics

Directory of Open Access Journals (Sweden)

Josep Claramunt

2017-02-01

Full Text Available The aim of this study is to develop a process to produce high-performance cement-based composites reinforced with flax nonwoven fabrics, analyzing the influence of the fabric structure—thickness and entanglement—on mechanical behavior under flexural and tensile loadings. For this purpose, composite with flax nonwoven fabrics with different thicknesses were first prepared and their cement infiltration was evaluated with backscattered electron (BSE images. The nonwoven fabrics with the optimized thickness were then subjected to a water treatment to improve their stability to humid environments and the fiber-matrix adhesion. For a fixed thickness, the effect of the nonwoven entanglement on the mechanical behavior was evaluated under flexural and direct tension tests. The obtained results indicate that the flax nonwoven fabric reinforcement leads to cement composites with substantial enhancement of ductility.

Medical effects of poly-ethylene terephthalate (PET) non-woven ...

African Journals Online (AJOL)

In this study, bamboo activated charcoal was mixed with acrylic resin in various proportions and deposited on poly-ethylene terephthalate (PET) non-woven fabrics. A series of characterizations were carried out to estimate the performances of PET non-woven fabrics such as far infrared ray emission, heat retention, negative ...

Different chemical groups modification on the surface of chitosan nonwoven dressing and the hemostatic properties.

Science.gov (United States)

Yan, Dong; Hu, Shihao; Zhou, Zhongzheng; Zeenat, Shah; Cheng, Feng; Li, Yang; Feng, Chao; Cheng, Xiaojie; Chen, Xiguang

2018-02-01

The hemostatic properties of surface modified chitosan nonwoven had been investigated. The succinyl groups, carboxymethyl groups and quaternary ammonium groups were introduced into the surface of chitosan nonwoven (obtained NSCS, CMCS and TMCS nonwoven, respectively). For blood clotting, absorbance value (0.105±0.03) of NSCS1 nonwoven was the smallest (CS 0.307±0.002, NSCS2 0.148±0.002, CMCS1 0.195±0.02, CMCS2 0.233±0.001, TMCS1 0.191±0.002, TMCS2 0.345±0.002), which indicated the stronger hemostatic potential. For platelet aggregation, adenosine diphosphate agonist was added to induce the nonwoven to adhered platelets. The aggregation of platelet with TMCS2 nonwoven was highest (10.97±0.16%). Further research of blood coagulation mechanism was discussed, which indicated NSCS and CMCS nonwoven could activate the intrinsic pathway of coagulation to accelerate blood coagulation. NSCS1 nonwoven showed the shortest hemostatic time (147±3.7s) and the lowest blood loss (0.23±0.05g) in a rabbit ear artery injury model. These results demonstrated that these surface modified chitosan nonwoven dressings could use as a promising hemostatic intervention, especially NSCS nonwoven dressing. Copyright © 2017 Elsevier B.V. All rights reserved.

Feasibility Assessments of the Use of Recycled Fibers in Nonwoven Fabrics

Directory of Open Access Journals (Sweden)

Jia-Horng Lin

2017-01-01

Full Text Available Environmental protection has become an increasing concern, which makes recycling and reclaiming highly important. In addition to governmental campaigns and promotion, enterprises should examine each perspective thoroughly in order to prevent excessive resource consumption. In this study, recycled materials, including recycled far-infrared polyester (FPET fiber, three-dimensional crimped hollow flame-retarding (TPET fiber, and low-melting-point polyester (LPET fiber, are used to form nonwoven fabrics. The influence of different amounts of FPET fiber, 0–80 wt %, on the properties of nonwoven fabrics was examined. The sheath of LPET fibers can be melted as a result of hot pressing, which provides cohesion between fibers that mechanically improves the nonwoven fabrics. The tensile strength, tearing strength, air permeability, and far infrared (FIR emissivity of the nonwoven fabrics were examined, thereby determining the optimal parameters. The test results show that the thermally treated nonwoven fabrics have better mechanical properties and FIR emissivity, compared to those of non-thermally treated nonwoven fabrics. Moreover, more FPET fibers cause the mechanical properties along the cross machine direction (CD to decrease by 9% and that along the machine direction (MD to decrease by 5%. In particular, all the thermally treated samples exhibit a FIR emissivity of 0.8, which is health-promoting.

Combination of natural fiber Boehmeria nivea (ramie) with matrix epoxide for bullet proof vest body armor

Energy Technology Data Exchange (ETDEWEB)

Anggoro, Didi Dwi, E-mail: anggorophd@gmail.com; Kristiana, Nunung, E-mail: nuna.c631@gmail.com [Master of Chemical Engineering, Faculty of Engineering, Diponegoro University Jln. Prof. Sudharto, Tembalang, Semarang, 50239 (Indonesia)

2015-12-29

Ballistic protection equipment, such as a bulletproof vest, is a soldier’s most important means of preserving life and survivability in extreme combat conditions. The bulletproof vests are designed to protect the user’s chest from injury without disturbing the ability to perform his duties. Aromatic polyamide or aramid fibers known under the trade name Kevlar, Trawon and so is synthetic fiber materials commonly used in the manufacture of bulletproof vests. This synthetic fibers have high tensile strength and ductility. Kevlar is expensive and imported material. In this study, will introduce local natural raw materials, ramie fiber (Boehmeria nivea) which is cheaper and environmentally friendly. It has enough tenacity and tensile strength as a bulletproof vest. This experiment uses two panels, there are Panel A as front surface of Panel B. Panel A is a combination of ramie and epoxide matrix, while panel B is only ramie. From several variations of experimental combinations between Panel A and Panel B, optimal combination obtained with 16 layers of panel A and 31-34 layers of panel B which is able to protect againts cal. 7.65 mm × 17 mm (.32 ACP) bullet fired through pistol .32 Pindad from a distance of 20 meters. Panel with a size of 20 cm × 20 cm has a total thickness between 12,922 to13,745 mm and a total weight between 506,26 to 520,926gram. Scanning electron microscopy (SEM) observations indicated that the porosity and surface area of the ramie fiber is smooth, fiber surfaces showed topography with micropores. SEM also showed well-arranged structure of fibers bonding. Energy Dispersive X-ray (EDX) analysis indicated 100 % carbon contents in ramie fiber. Test result indicates that panel from composite ramie-epoxide can reach the level 1of International Standard of NIJ - 010104. Compared to panel from polyester fiber, the panel from composite ramie-epoxide (0,50-0,52 kg) is lighter weight than panel polyester fiber (1,642 kg)

Combination of natural fiber Boehmeria nivea (ramie) with matrix epoxide for bullet proof vest body armor

International Nuclear Information System (INIS)

Anggoro, Didi Dwi; Kristiana, Nunung

2015-01-01

Ballistic protection equipment, such as a bulletproof vest, is a soldier’s most important means of preserving life and survivability in extreme combat conditions. The bulletproof vests are designed to protect the user’s chest from injury without disturbing the ability to perform his duties. Aromatic polyamide or aramid fibers known under the trade name Kevlar, Trawon and so is synthetic fiber materials commonly used in the manufacture of bulletproof vests. This synthetic fibers have high tensile strength and ductility. Kevlar is expensive and imported material. In this study, will introduce local natural raw materials, ramie fiber (Boehmeria nivea) which is cheaper and environmentally friendly. It has enough tenacity and tensile strength as a bulletproof vest. This experiment uses two panels, there are Panel A as front surface of Panel B. Panel A is a combination of ramie and epoxide matrix, while panel B is only ramie. From several variations of experimental combinations between Panel A and Panel B, optimal combination obtained with 16 layers of panel A and 31-34 layers of panel B which is able to protect againts cal. 7.65 mm × 17 mm (.32 ACP) bullet fired through pistol .32 Pindad from a distance of 20 meters. Panel with a size of 20 cm × 20 cm has a total thickness between 12,922 to13,745 mm and a total weight between 506,26 to 520,926gram. Scanning electron microscopy (SEM) observations indicated that the porosity and surface area of the ramie fiber is smooth, fiber surfaces showed topography with micropores. SEM also showed well-arranged structure of fibers bonding. Energy Dispersive X-ray (EDX) analysis indicated 100 % carbon contents in ramie fiber. Test result indicates that panel from composite ramie-epoxide can reach the level 1of International Standard of NIJ - 010104. Compared to panel from polyester fiber, the panel from composite ramie-epoxide (0,50-0,52 kg) is lighter weight than panel polyester fiber (1,642 kg)

RAMI analysis of the ITER LFS CTS system

DEFF Research Database (Denmark)

Infante, V.; Henriques, E.; Gonçalves, B.

2017-01-01

with the methodology pursued. The Functional Analysis, developed both at system and sub-system level, are the major inputs for the RAMI analysis. A systematic approach has been used, and significant design assumptions have been made due to the lack of knowledge and definition inherent to preliminary design stages...

Ramie (Boehmeria nivea) decortication waste bio-briquette business model canvas with design thinking approach

Science.gov (United States)

Pahlavi, Ghifari Rezka; Purnomo, Dwi; Bunyamin, Anas; Wulandari, Asri Peni

2017-03-01

Ramie (Boehmeria nivea) is a plant that can produce fibers from its stem but in the production process, it still produces waste containing high lignin and cellulose. The high content of these substances can be used as bio-briquette raw material because they can produce carbon and can offer a business opportunity to establish bio-briquette industry. The purpose of this study is to obtain a ramie decortification waste bio-briquette business model because until now there is no bio-briquette has been made from ramie decortication waste as its raw material. This research uses descriptive analysis method with a design thinking approach. The result of this research shows that the business model canvas is designed based on consumer's experience when interacting with the product via customer journey tool in order to get the business model in accordance with customer expectations.

Optimization of Pan Bread Prepared with Ramie Powder and Preservation of Optimized Pan Bread Treated by Gamma Irradiation during Storage

International Nuclear Information System (INIS)

Lee, H.J.; Joo, N.M.

2012-01-01

This study was conducted to develop an optimal composite recipe for pan bread with ramie powder that has high sensory approval with all age groups and to estimate the DPPH radical scavenging activity and the pan bread shelf life after gamma irradiation. The sensory evaluation results showed significant differences in flavor (p less than 0.05), appearance (p less than 0.01), color (p less than 0.01), moistness (p less than 0.01), and overall quality (p less than 0.05) based on the amount of ramie powder added. As a result, the optimum formulations by numerical and graphical methods were calculated to be as follows: ramie powder 2.76 g (0.92%) and water 184.7 mL. Optimized pan bread with ramie powder and white pan bread were irradiated with gamma-rays at doses of 0, 10, 15, and 20 kGy. The total bacterial growth increased with the longer storage time and the least amount of ramie powder added. Consequently, these results suggest that the addition of ramie powder to pan bread provides added value to the bread in terms of increased shelf life

Industry 4.0 - How will the nonwoven production of tomorrow look like?

Science.gov (United States)

Cloppenburg, F.; Münkel, A.; Gloy, Y.; Gries, T.

2017-10-01

Industry 4.0 stands for the on-going fourth industrial revolution, which uses cyber physical systems. In the textile industry the terms of industry 4.0 are not sufficiently known yet. First developments of industry 4.0 are mainly visible in the weaving industry. The cost structure of the nonwoven industry is unique in the textile industry. High shares of personnel, energy and machine costs are distinctive for nonwoven producers. Therefore the industry 4.0 developments in the nonwoven industry should concentrate on reducing these shares by using the work force efficiently and by increasing the productivity of first-rate quality and therefore decreasing waste production and downtimes. Using the McKinsey digital compass three main working fields are necessary: Self-optimizing nonwoven machines, big data analytics and assistance systems. Concepts for the nonwoven industry are shown, like the “EasyNonwoven” concept, which aims on economically optimizing the machine settings using self-optimization routines.

Comparative Study of the Properties of some Non-Woven Diapers ...

African Journals Online (AJOL)

ABSTRACT: The properties of locally made non-woven diapers were studied. Four locally made non-woven absorbent pads samples namely; Always ultra absorbent pad (sample A), Dr. Brown absorbent pad (sample B),. Everyday ultra thin normal absorbent pad (sample C), and Enjoy leto absorbent pad (sample D) were ...

Assembly of graphene oxide on nonconductive nonwovens by the synergistic effect of interception and electrophoresis

Energy Technology Data Exchange (ETDEWEB)

Jiao, Kunyan; Zhu, Ting; Li, Xianhua; Shan, Mingjing; Xu, Zhiwei, E-mail: xuzhiwei@tjpu.edu.cn; Jiao, Yanan [Tianjin Polytechnic University, Key Laboratory of Advanced Braided Composites, Ministry of Education (China)

2015-09-15

Electrophoretic deposition has always been an attractive method to deposit nanoparticles on conductive materials, while most fiber-based materials have poor conductivity which limits the application of electrophoretic deposition in assembling nanoparticles onto fiber-based materials. A new approach to assemble graphene oxide (GO) nanosheets on nonconductive nonwovens via the synergistic effect of electrophoresis and fiber interception was reported in this study. To improve surface wettability, polypropylene (PP) nonwovens were modified by acrylic acid and subsequent N{sub 2} plasma treatment. Then GO nanosheets were anchored onto modified nonwovens by electrophoresis process and nonwoven interception. The results of scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) manifested that etching and grafting simultaneously occurred on the surface of modified PP nonwovens, resulting in a great improvement of nonwoven hydrophily, which corresponded to the results of water contact angle. Furthermore, the results of X-ray diffraction, energy dispersive X-ray, SEM, and FTIR indicated that different amounts of GO nanosheets were successfully assembled onto modified PP nonwovens. This method provides a new avenue for incorporating carbon nanoparticles with nonconductive fiber-based materials, and modified PP nonwovens assembled with GO nanosheets show good air filtration performance for sodium chloride aerosol with a filtration efficiency of 87.9 % and a pressure drop of 36.4 mmH{sub 2}O, and the reduced GO/PP composite nonwovens exhibit enhanced conductivity.

Development of a high-density nonwoven structure to improve the stab resistance of protective clothing material.

Science.gov (United States)

Bao, Limin; Wang, Yanling; Baba, Takeichiro; Fukuda, Yasuhiro; Wakatsuki, Kaoru; Morikawa, Hideaki

2017-12-07

The purpose of this research was to enhance the stab resistance of protective clothing material by developing a new high-density nonwoven structure. Ice picks often injure Japanese police officers due to the strict regulation of swords in the country. Consequently, this study was designed to improve stab resistance against ice picks. Most existing anti-stab protective clothing research has focused on various fabrics impregnated with resin, an approach that brings with it problems of high cost and complicated processing. Seldom has research addressed the potential for improving stab resistance by using nonwoven structures, which exhibit better stab resistance than fabric. In this research, we prepared a series of nonwoven structures with densities ranging from about 0.14 g/cm 3 to 0.46 g/cm 3 by varying the number of stacked layers of Kevlar/polyester nonwoven under a hot press. We then proposed two methods for producing such hot-press nonwovens: the multilayer hot-press method and the monolayer hot-press method. Stab resistance was evaluated according to NIJ Standard-0115.00. We also investigated the relationship among nonwoven density, stab resistance, and flexural rigidity, and here we discuss the respective properties of the two proposed methods. Our results show that stab resistance and flexural rigidity increase with nonwoven density, but flexural rigidity of nonwovens prepared using the monolayer hot-press method only shows a slight change as nonwoven density increases. Though the two methods exhibit little difference in maximum load, the flexural rigidity of nonwovens prepared using the monolayer hot-press method is much lower, which contributes to superior wear comfort. Finally, we investigated the mechanism behind the stabbing process. Stabbing with an ice pick is a complicated process that involves many factors. Our findings indicate that nonwovens stop penetration primarily in two ways: nonwoven deformation and fiber fractures.

Determination of fissile fraction in MOX (mixed U + Pu oxides) fuels for different burnup values

International Nuclear Information System (INIS)

Ozdemir, Levent; Acar, Banu Bulut; Zabunoglu, Okan H.

2011-01-01

When spent Light Water Reactor fuels are processed by the standard Purex method of reprocessing, plutonium (Pu) and uranium (U) in spent fuel are obtained as pure and separate streams. The recovered Pu has a fissile content (consisting of 239 Pu and 241 Pu) greater than 60% typically (although it mainly depends on discharge burnup of spent fuel). The recovered Pu can be recycled as mixed-oxide (MOX) fuel after being blended with a fertile U makeup in a MOX fabrication plant. The burnup that can be obtained from MOX fuel depends on: (1) isotopic composition of Pu, which is closely related to the discharge burnup of spent fuel from which Pu is recovered; (2) the type of fertile U makeup material used (depleted U, natural U, or recovered U); and (3) fraction of makeup material in the mix (blending ratio), which in turn determines the total fissile fraction of MOX. Using the Non-linear Reactivity Model and the code MONTEBURNS, a step-by-step procedure for computing the total fissile content of MOX is introduced. As was intended, the resulting expression is simple enough for quick/hand calculations of total fissile content of MOX required to reach a desired burnup for a given discharge burnup of spent fuel and for a specified fertile U makeup. In any case, due to non-fissile (parasitic) content of recovered Pu, a greater fissile fraction in MOX than that in fresh U is required to obtain the same burnup as can be obtained by the fresh U fuel.

Comparison of U-Pu-Mo, U-Pu-Nb, U-Pu-Ti and U-Pu-Zr alloys; Comparaison des alliages U-Pu-Mo, U-Pu-Nb, U-Pu-Ti, U-Pu-Zr

Energy Technology Data Exchange (ETDEWEB)

Boucher, R; Barthelemy, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

The data concerning the U-Pu, U-Pu-Mo and U-Pu-Nb are recalled. The results obtained with U-Pu-Ti and U-Pu-Zr alloys containing 15-20 per cent Pu and 10 wt. per cent ternary element are reported. The transformation temperatures, the expansion coefficients, the nature of phases, the thermal cycling behaviour have been determined. A list of the principal properties of these different alloys is presented and the possibilities of their use as fast reactor's fuel element are considered. The U-Pu-Ti alloys seem to be quite promising: easiness of fabrication, large thermal stability, excellent behaviour in air, small quantity of zeta phase, temperature of solidus superior to 1100 deg. C. (authors) [French] On rappelle brievement les connaissances acquises sur les alliages U-Pu, U-Pu-Mo et U-Pu-Nb. On presente les resultats obtenus avec les alliages U-Pu-Ti et U-Pu-Zr pour des teneurs de 15 a 20 pour cent de plutonium et 10 pour cent en poids d'element ternaire. On a determine les temperatures de transformation, les coefficients de dilatation, la nature des phases, la conductibilite thermique a 20 deg. C, la tenue au cyclage thermique et diverses autres proprietes. Un tableau resume les principales proprietes des divers alliages. On considere les possibilites d'emploi de ces alliages comme combustibles de reacteur rapide. Les alliages U-Pu-Ti paraissent particulierement interessants: facilite d'elaboration, stabilite thermique etendue, tenue dans l'air excellente, faible quantite de la phase U-Pu zeta, temperature de fusion commencante superieure a 1100 deg. C. (auteurs)

Adsorption and recovery of lead(II) from aqueous solutions by immobilized Pseudomonas Aeruginosa PU21 beads

International Nuclear Information System (INIS)

Lin, C.-C.; Lai, Y.-T.

2006-01-01

In this study, immobilized Pseudomonas aeruginosa PU21 beads were used as an adsorbent for lead(II). Different weight percentages of chitosan were added to polyethylene glycol (PEG, 0.5 wt.% in aqueous solution) and alginate (18 wt.% in aqueous solution), and then blended or cross-linked using different concentrations of epichlorohydrin (ECH) to prepare beads of different sizes and increased mechanical strength. Before blending or cross-linking, different weight percentages of P. aeruginosa PU21 were added to increase lead(II) adsorption. Subsequently the optimized bead composition (concentration of ECH, percentages of chitosan and P. aeruginosa PU21) and the optimum adsorption conditions (agitation rate and pH in the aqueous solution) were ascertained. Finally, the optimized beads adsorbing lead(II) were regenerated by 0.1 M aqueous HCl solutions and the most effective desorption agitation rate was ascertained. The results indicate that the reuse of immobilized P. aeruginosa PU21 beads was feasible. In addition, the equilibrium adsorption, kinetics, changes in the thermodynamic properties of adsorption of lead(II) on optimized beads were also investigated

Next Generation Non-particulate Dry Nonwoven Pad for Chemical Warfare Agent Decontamination

Energy Technology Data Exchange (ETDEWEB)

Ramkumar, S S; Love, A; Sata, U R; Koester, C J; Smith, W J; Keating, G A; Hobbs, L; Cox, S B; Lagna, W M; Kendall, R J

2008-05-01

New, non-particulate decontamination materials promise to reduce both military and civilian casualties by enabling individuals to decontaminate themselves and their equipment within minutes of exposure to chemical warfare agents or other toxic materials. One of the most promising new materials has been developed using a needlepunching nonwoven process to construct a novel and non-particulate composite fabric of multiple layers, including an inner layer of activated carbon fabric, which is well-suited for the decontamination of both personnel and equipment. This paper describes the development of a composite nonwoven pad and compares efficacy test results for this pad with results from testing other decontamination systems. The efficacy of the dry nonwoven fabric pad was demonstrated specifically for decontamination of the chemical warfare blister agent bis(2-chloroethyl)sulfide (H or sulfur mustard). GC/MS results indicate that the composite fabric was capable of significantly reducing the vapor hazard from mustard liquid absorbed into the nonwoven dry fabric pad. The mustard adsorption efficiency of the nonwoven pad was significantly higher than particulate activated carbon (p=0.041) and was similar to the currently fielded US military M291 kit (p=0.952). The nonwoven pad has several advantages over other materials, especially its non-particulate, yet flexible, construction. This composite fabric was also shown to be chemically compatible with potential toxic and hazardous liquids, which span a range of hydrophilic and hydrophobic chemicals, including a concentrated acid, an organic solvent and a mild oxidant, bleach.

Comparison of Three Methods for Generating Superhydrophobic, Superoleophobic Nylon Nonwoven Surfaces (Postprint)

Science.gov (United States)

2011-04-01

film and onto a 100 g/ m2 nylon nonwoven substrate was carried out in a cylindri- cal , inductively coupled plasma reactor (10 cm diameter and 2700 cm3...the Nonwoven Institute (NI) for sharing hydro- entangled nonwoven fabric with us. References 1. Barthlott W, Neinhuis C (1997) Planta 202:1 2. Wu X...Faraday Soc 40:546 8. Lee H (2009) J Mater Sci 44:4645. doi:10.1007/s10853-009- 3711-5 9. Hoefnagels H, Wu D, de With G, Ming W (2007) Langmuir 23

RAMI analysis of the ITER Central Safety System

Energy Technology Data Exchange (ETDEWEB)

Kitazawa, Sin-iti, E-mail: kitazawa.siniti@jaea.go.jp [ITER Project Unit, Japan Atomic Energy Agency (JAEA), Naka, 311-0193 Ibaraki (Japan); Okayama, Katsumi [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Neyatani, Yuzuru [ITER Project Unit, Japan Atomic Energy Agency (JAEA), Naka, 311-0193 Ibaraki (Japan); Sagot, Francois; Houtte, Didier van [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

2014-06-15

Highlights: • We performed the functional analysis of the ITER CSS. • We performed a failure mode analysis of the ITER CSS. • We estimated the reliability and availability of the ITER CSS. • The ITER RAMI approach was applied to the ITER CSS for technical risk control in the design phase. - Abstract: ITER is the first worldwide international project aiming to design a facility to produce nuclear fusion energy. The technical requirements of its plant systems have been established in the ITER Project Baseline. In the project, the Reliability, Availability, Maintainability and Inspectability (RAMI) approach has been adopted for technical risk control to help aid the design of the components in preparation for operation and maintenance. A RAMI analysis was performed on the conceptual design of the ITER Central Safety System (CSS). A functional breakdown was prepared in a bottom-up approach, resulting in the system being divided into 2 main functions and 20 sub-functions. These functions were described using the IDEF0 method. Reliability block diagrams were prepared to estimate the reliability and availability of each function under the stipulated operating conditions. Initial and expected scenarios were analyzed to define risk-mitigation actions. The inherent availability of the ITER CSS expected after implementation of mitigation actions was calculated to be 99.80% over 2 years, which is the typical interval of the scheduled maintenance cycles. This is consistent with the project required value of 99.9 ± 0.1%. A Failure Modes, Effects and Criticality Analysis was performed with criticality charts highlighting the risk level of the different failure modes with regard to their probability of occurrence and their effects on the availability of the plasma operation. This analysis defined when risk mitigation actions were required in terms of design, testing, operation procedures and/or maintenance to reduce the risk levels and increase the availability of the

Preliminary RAMI analysis of DFLL TBS for ITER

Energy Technology Data Exchange (ETDEWEB)

Wang, Dagui [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230031 (China); Yuan, Run [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Wang, Jiaqun, E-mail: jiaqun.wang@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Wang, Fang; Wang, Jin [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

2016-11-15

Highlights: • We performed the functional analysis of the DFLL TBS. • We performed a failure mode analysis of the DFLL TBS. • We estimated the reliability and availability of the DFLL TBS. • The ITER RAMI approach was applied to the DFLL TBS for technical risk control in the design phase. - Abstract: ITER is the first fusion machine fully designed to prove the physics and technological basis for next fusion power plants. Among the main technical objectives of ITER is to test and validate design concepts of tritium breeding blankets relevant to the fusion power plants. To achieve this goal, China has proposed the dual functional lithium-lead test blanket module (DFLL TBM) concept design. The DFLL TBM and its associated ancillary system were called DFLL TBS. The DFLL TBS play a key role in next fusion reactor. In order to ensure reliable and available of DFLL TBS, the risk control project of DFLL TBS has been put on the schedule. As the stage of the ITER technical risk control policy, the RAMI (Reliability, Availability, Maintainability, Inspectability) approach was used to control the technical risk of ITER. In this paper, the RAMI approach was performed on the conceptual design of DFLL TBS. A functional breakdown was prepared on DFLL TBS, and the system was divided into 3 main functions and 72 basic functions. Based on the result of functional breakdown of DFLL TBS, the reliability block diagrams were prepared to estimate the reliability and availability of each function under the stipulated operating conditions. The inherent availability of the DFLL TBS expected after implementation of mitigation actions was calculated to be 98.57% over 2 years based on the ITER reliability database. A Failure Modes Effects and Criticality Analysis (FMECA) was performed with criticality charts highlighting the risk level of the different failure modes with regard to their probability of occurrence and their effects on the availability.

Performance of diatomite/iron oxide modified nonwoven membrane used in membrane bioreactor process for wastewater reclamation.

Science.gov (United States)

He, Yueling; Zhang, Wenqi; Rao, Pinhua; Jin, Peng

2014-01-01

This study describes an approach for surface modification of a nonwoven membrane by diatomite/iron oxide to examine its filterability. Analysis results showed that nonwoven hydrophilicity is enhanced. Static contact angle decreases dramatically from 122.66° to 39.33°. Scanning electron micrograph images show that diatomite/iron oxide is attached on nonwoven fiber. X-ray diffraction analysis further proves that the compound is mostly magnetite. Fourier transformed infrared spectra results reveal that two new absorption peaks might be attributed to Si-O and Fe-O, respectively. Modified and original membranes were used in double nonwoven membrane bioreactors (MBRs) for synthetic wastewater treatment. High critical flux, long filtration time, slow trans-membrane pressure rise and stable sludge volume index confirmed the advantages of modified nonwoven. Comparing with original nonwoven, similar effluent qualities are achieved, meeting the requirements for wastewater reclamation.

Increasing Mechanical Properties of 2-D-Structured Electrospun Nylon 6 Non-Woven Fiber Mats

Directory of Open Access Journals (Sweden)

Chunhui Xiang

2016-04-01

Full Text Available Tensile strength, Young’s modulus, and toughness of electrospun nylon 6 non-woven fiber mats were improved by increasing individual nanofiber strength and fiber–fiber load sharing. Single-walled carbon nanotubes (CNTs were used as reinforcement to increase the strength of the electrospun nylon 6 nanofibers. Young’s modulus, tensile strength, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % solutions increased 51%, 87%, and 136%, respectively, after incorporating 1 wt % CNTs into the nylon 6 nanofibers. Three methods were investigated to enhance fiber–fiber load sharing: increasing friction between fibers, thermal bonding, and solvent bonding. The addition of beaded nylon 6 nanofibers into the non-woven fiber mats to increase fiber-fiber friction resulted in a statistically significantly increase in Young’s modulus over comparable smooth non-woven fiber mats. After annealing, tensile strength, elongation, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % + 10 wt % solutions increased 26%, 28%, and 68% compared to those from 20 wt % solutions. Solvent bonding with formic acid vapor at room temperature for 30 min caused increases of 56%, 67%, and 39% in the Young’s modulus, tensile strength, and toughness of non-woven fiber mats, respectively. The increases attributed to increased individual nanofiber strength and solvent bonding synergistically resulted in the improvement of Young’s modulus of the electrospun nylon 6 non-woven fiber mats.

Post-traumatic Perineal Pubic Rami Protrusion: A Simple Surgical Management

Directory of Open Access Journals (Sweden)

Voon Victor

2014-06-01

Full Text Available Although pubic ramus fractures are common, they usually heal without surgical intervention and result in little long-term disability. We herein present two cases of symptomatic malunion of pubic rami fracture, which was successfully treated with a simple and safe surgical technique. The patients' local symptoms resolved afterwards.

Conservative Management of Unilateral Fractures of the Mandibular Rami in Horses.

Science.gov (United States)

Jansson, Nicolai

2016-11-01

To report the outcome of conservative management of unilateral fractures of the mandibular rami in horses. Retrospective case series. 24 client-owned horses with unilateral mandibular fractures METHODS: Medical records (January 2000-January 2014) of horses with unilateral mandibular ramus fractures were retrieved. Only conservatively managed horses with follow-up information were included. Follow-up information on clinical outcome was retrieved from the medical records (n=11) or obtained by telephone interviews with the owners or trainers (n=13). Twenty-three horses (96%) returned to their previous or intended use and had no clinically evident masticatory or fracture healing-related problems at the time of follow-up. The owner of 1 horse (4%) reported it had tooth loosening, feed impaction, and masticatory problems. Conservative management of unilateral fractures of the mandibular rami is a treatment option in horses. © Copyright 2016 by The American College of Veterinary Surgeons.

Preparation and Characterization of Polypropylene Non-woven Fabrics Prepared by Melt-blown Spinning for Filtration Membranes

Energy Technology Data Exchange (ETDEWEB)

Chu, Konghee; Park, Mira; Kim, Hakyong [Chonbuk National Univ., Jeonju (Korea, Republic of); Jin, Fanlong; Park, Soojin [Inha Univ., Incheon (Korea, Republic of)

2014-06-15

PP non-woven fabrics were prepared by melt-blown spinning, followed by heat and plasma treatments. After heat treatment, the PP non-woven fabrics displayed decreased water flux, increased tensile strength, decreased elongation, and an average pore size of 0.7 μm. The hydrophilicity of the PP non-woven fabrics was improved by plasma treatment. The water flux of the PP non-woven fabrics increased about two fold after the plasma treatment. The particle removal efficiency was determined to be 97.2-99.4% for 1-3 μm sized particles, demonstrating a high particle removal efficiency. Polypropylene (PP) non-woven fabrics have been widely used as filtration membranes in wastewater purification with industrial applications due to their low cost, good mechanical strength, and high thermal and chemical stability. The membrane fouling behavior depends strongly on the physical and mechanical properties of the membrane, including pore size, porosity, morphology, and hydrophilicity. In general, PP non-woven fabrics have poor hydrophilicity; this has limited their application in the biomedical field. It is therefore necessary to develop PP non-woven fabrics with improved surface hydrophilicity to increase the scope of their use. Plasma treatment, an environmentally friendly alternative to traditional chemical activation, only changes the uppermost atomic layers of a membrane surface without affecting the bulk properties of the polymer.

Comparison of U-Pu-Mo, U-Pu-Nb, U-Pu-Ti and U-Pu-Zr alloys

International Nuclear Information System (INIS)

Boucher, R.; Barthelemy, P.

1964-01-01

The data concerning the U-Pu, U-Pu-Mo and U-Pu-Nb are recalled. The results obtained with U-Pu-Ti and U-Pu-Zr alloys containing 15-20 per cent Pu and 10 wt. per cent ternary element are reported. The transformation temperatures, the expansion coefficients, the nature of phases, the thermal cycling behaviour have been determined. A list of the principal properties of these different alloys is presented and the possibilities of their use as fast reactor's fuel element are considered. The U-Pu-Ti alloys seem to be quite promising: easiness of fabrication, large thermal stability, excellent behaviour in air, small quantity of zeta phase, temperature of solidus superior to 1100 deg. C. (authors) [fr

RAMI modeling of selected balance of plant systems for the proposed Accelerator Production of Tritium (APT) project

International Nuclear Information System (INIS)

Radder, J.A.; Cramer, D.S.

1997-01-01

In order to meet Department of Energy (DOE) Defense Program requirements for tritium in the 2005-2007 time frame, new production capability must be made available. The Accelerator Production of Tritium (APT) Plant is being considered as an alternative to nuclear reactor production of tritium, which has been the preferred method in the past. The proposed APT plant will use a high-power proton accelerator to generate thermal neutrons that will be captured in 3 He to produce tritium (3H). It is expected that the APT Plant will be built and operated at the DOE's Savannah River Site (SRS) in Aiken, South Carolina. Discussion is focused on Reliability, Availability, Maintainability, and Inspectability (RAMI) modeling of recent conceptual designs for balance of plant (BOP) systems in the proposed APT Plant. In the conceptual designs for balance of plant (BOP) systems in the proposed APT Plant. In the conceptual design phase, system RAMI estimates are necessary to identify the best possible system alternative and to provide a valid picture of the cost effectiveness of the proposed system for comparison with other system alternatives. RAMI estimates in the phase must necessarily be based on generic data. The objective of the RAMI analyses at the conceptual design stage is to assist the designers in achieving an optimum design which balances the reliability and maintainability requirements among the subsystems and components

Renewable and superior thermal-resistant cellulose-based composite nonwoven as lithium-ion battery separator.

Science.gov (United States)

Zhang, Jianjun; Liu, Zhihong; Kong, Qingshan; Zhang, Chuanjian; Pang, Shuping; Yue, Liping; Wang, Xuejiang; Yao, Jianhua; Cui, Guanglei

2013-01-01

A renewable and superior thermal-resistant cellulose-based composite nonwoven was explored as lithium-ion battery separator via an electrospinning technique followed by a dip-coating process. It was demonstrated that such nanofibrous composite nonwoven possessed good electrolyte wettability, excellent heat tolerance, and high ionic conductivity. The cells using the composite separator displayed better rate capability and enhanced capacity retention, when compared to those of commercialized polypropylene separator under the same conditions. These fascinating characteristics would endow this renewable composite nonwoven a promising separator for high-power lithium-ion battery.

The development of nonwoven fabric and agricultural bed soil using kapok fiber for industrial usages

International Nuclear Information System (INIS)

Chung, Byung Yeoup; Kim, Jin Hong; Lee, Seung Sik

2010-01-01

The purpose of this project is the development of nonwoven fabric using natural kapok fiber and synthetic fiber for industrial usages and the development of manufacturing techniques for nursery bed soil using kapok fiber. Research scopes include the development of agricultural bed soil using kapok fiber and nonwoven fabric using kapok fiber. Main results are as follow; the physico-chemical characterization of kapok fiber (water holding capacity, bulk density, water retention curve, viscoelastic measurement, oil adsorption capacity, analysis of essential elements, measurement of anion and cation); the physico-chemical characterization of kapok bed soil; the evidence experiment of kapok bed soil; the optimum content of kapok fiber and synthetic fiber for nonwoven fabric; establishment of the optimum radiation dose for manufacturing kapok nonwoven fabric

Agrobacterium-mediated genetic transformation and regeneration of transgenic plants using leaf midribs as explants in ramie [Boehmeria nivea (L.) Gaud].

Science.gov (United States)

An, Xia; Wang, Bo; Liu, Lijun; Jiang, Hui; Chen, Jie; Ye, Shengtuo; Chen, Leiyu; Guo, Pingan; Huang, Xing; Peng, Dingxiang

2014-05-01

In this study, leaf midribs, the elite explants, were used for the first time to develop an efficient regeneration and transformation protocol for ramie [Boehmeria nivea (L.) Gaud.] via Agrobacterium-mediated genetic transformation. Sensitivity of leaf midribs regeneration to kanamycin was evaluated, which showed that 40 mg l(-1) was the optimal concentration needed to create the necessary selection pressure. Factors affecting the ramie transformation efficiency were evaluated, including leaf age, Agrobacterium concentration, length of infection time for the Agrobacterium solution, acetosyringone concentration in the co-cultivation medium, and the co-cultivation period. The midrib explants from 40-day-old in vitro shoots, an Agrobacterium concentration at OD600 of 0.6, 10-min immersion in the bacteria solution, an acetosyringone concentration of 50 mg l(-1) in the co-cultivation medium and a 3-day co-cultivation period produced the highest efficiencies of regeneration and transformation. In this study, the average transformation rate was 23.25%. Polymerase chain reactions using GUS and NPTII gene-specific primers, Southern blot and histochemical GUS staining analyses further confirmed that the transgene was integrated into the ramie genome and expressed in the transgenic ramie. The establishment of this system of Agrobacterium-mediated genetic transformation and regeneration of transgenic plants will be used not only to introduce genes of interest into the ramie genome for the purpose of trait improvement, but also as a common means of testing gene function by enhancing or inhibiting the expression of target genes.

Effects of the Addition of Sodium Alginate and the Concentration of Calcium Chloride on the Properties of Composite Nonwoven Fabrics

Directory of Open Access Journals (Sweden)

Lou Ching-Wen

2016-01-01

Full Text Available Nonwoven fabrics have merits, and for example, they can be simply and quickly processed with a variety of materials and an easily changeable manufacturing process. This study aims to examine the influences of the addition of sodium alginate (SA and the concentration of calcium chloride (CaCl2 on the properties of the composite nonwoven fabrics. Chitosan (CS micro-particles and SA solution are cross-linked with CaCl2 with various concentrations, combined with farir heat preservative staples (FT/cotton (C nonwoven fabrics, and then freeze-dried to form CS/SA/FT/C composite nonwoven fabrics. Afterwards, physical property tests are performed on the resulting composite nonwoven fabrics to determine their properties as related to various concentrations of CaCl2. The addition of SA decreases the water vapor permeability of FT/C nonwoven fabrics by 15 %, but the concentrations of CaCl2 do not influence the water vapor permeability. Compared to FT/C nonwoven fabrics, CS/SA/FT/C composite nonwoven fabrics have significantly lower water absorbency and water vapor permeability, but a greater stiffness.

Fuel-pellet-fabrication experience using direct-denitration-recycle-PuO2-coprecipitated mixed oxide

International Nuclear Information System (INIS)

Rasmussen, D.E.; Schaus, P.S.

1980-01-01

The fuel pellet fabrication experience described in this paper involved three different feed powders: coprecipitated PuO 2 -UO 2 which was flash calcined in a fluidized bed; co-direct denitrated PuO 2 -UO 2 ; and direct denitrated LWR recycle PuO 2 which was mechanically blended with natural UO 2 . The objectives of this paper are twofold; first, to demonstrate that acceptable quality fuel pellets were fabricated using feed powders manufactured by processes other than the conventional oxalate process; and second, to highlight some pellet fabrication difficulties experienced with the direct denitration LWR recycle PuO 2 feed material, which did not produce acceptable pellets. The direct denitration LWR recycle PuO 2 was available as a by-product and was not specifically produced for use in fuel pellet fabrication. Nevertheless, its characteristics and pellet fabrication behavior serve to re-emphasize the importance of continued process development involving both powder suppliers and fuel fabricators to close the fuel cycle in the future

Changing perspectives on community identity and function: A remote sensing and artifactual re-analysis of Barton Ramie, Belize

Science.gov (United States)

Weller, Errin Teresa

This dissertation presents the results of the remote sensing and artifact re-analysis of the archaeological site of Barton Ramie, Belize. The site was the focus of Dr. Gordon R. Willey's innovative archaeological program in the Belize River Valley to study ancient Maya settlement, environment, and population in 1954-1956. Through the use of artifact analysis combined with the examination of high-resolution Worldview-1 imagery and a Geographic Information System (GIS)-based spatial analysis, I consider how the inhabitants of Barton Ramie forged community functioning and identity. I focus on the range of intra-site diversity including differential access to labor, goods, land, and the activities evidenced in households and non-domestic structures. Using a community theory framework, emphasizing the many practices that tied the community together, I underscore the variability expressed in architectural elaboration, sumptuary goods, ritual, and specialization. That variability has profound implications for understanding community diversity and economic, social, and ritual functioning. High-resolution panchromatic Worldview-1 satellite imagery successfully detected the remains of Barton Ramie settlement. Surface archaeology has been largely destroyed due to extensive agricultural activities in recent decades. GIS analysis and ground-truthing determined that mound size is the primary factor enabling detection of ancient features. The confirmation of features in an intensively plowed environment has implications including settlement, survey, and population for other disturbed environments. I argue that the Barton Ramie community developed from a complex interaction of networks and practices. These include activities at the household level, articulation between households to form sub-communities (or neighborhoods), and a larger imagined community of the Barton Ramie polity. Individual households articulated to form seven discrete sub-communities, bounded by landscape

The design of financial recording system in industrial bio-briquette of Ramie (Boehmeria nivea) decortication waste with design thinking approach

Science.gov (United States)

Irianto, R.; Purnomo, D.; Prima, S.; Wulandari, A.

2017-05-01

The production process of ramie (boehmeria nivea) fibers generates waste which contents 5.95 to 7.83% ash; 1.88 to 2.87% silicate; 30.67 to 31.08% lignin; 33.81 to 35.99% alpha cellulose; 62.95 to 63.78% holoselulosa; 17.43 to 18.14% pentosan, which can be used as raw material of bio-briquette. Those potential can be used to generate a business opportunity, such as industrial bio-briquette of ramie decortication waste. The purpose of this research is to create accounting information which could present an income statement that is easily applied on industrial bio-briquette of ramie decortication waste. This research use descriptive analysis method with design with design thinking approach to gather the information through depth observation on human being as the object to achieve the purpose. The result in this research is financial recording system of industrial bio-briquette of ramie decortication waste in a desktop application. The system is integrated with production activities according to the needs of accounting information particularly at managerial production. The existing applications creates information in the form of financial operations which can be used as a factor in decision-making.

Third Radiation Transfer Model Intercomparison (RAMI) exercise : Documenting progress in canopy reflectance models

NARCIS (Netherlands)

Widlowski, J.-L.; Taberner, M.; Pinty, B.; Bruniquel-Pinel, V.; Disney, M.; Fernandes, R.; Gastellu-Etchegorry, J.P.; Gobron, N.; Kuusk, A.; Lavergne, T.; Leblanc, S.; Lewis, P.E.; Martin, E.; Mottus, M.; North, P.R.J.; Qin, W.; Robustelli, M.; Rochdi, N.; Ruiloba, R.; Soler, C.; Thompson, R.; Verhoef, W.; Xie, D.; Thompson, R.

2007-01-01

The Radiation Transfer Model Intercomparison (RAMI) initiative benchmarks canopy reflectance models under well‐controlled experimental conditions. Launched for the first time in 1999, this triennial community exercise encourages the systematic evaluation of canopy reflectance models on a voluntary

Pu-239 and Pu-240 inventories and Pu-240/ Pu-239 atom ratios in the water column off Sanriku, Japan.

Science.gov (United States)

Yamada, Masatoshi; Zheng, Jian; Aono, Tatsuo

2013-04-01

A magnitude 9.0 earthquake and subsequent tsunami occurred in the Pacific Ocean off northern Honshu, Japan, on 11 March 2011 which caused severe damage to the Fukushima Dai-ichi Nuclear Power Plant. This accident has resulted in a substantial release of radioactive materials to the atmosphere and ocean, and has caused extensive contamination of the environment. However, no information is available on the amounts of radionuclides such as Pu isotopes released into the ocean at this time. Investigating the background baseline concentration and atom ratio of Pu isotopes in seawater is important for assessment of the possible contamination in the marine environment. Pu-239 (half-life: 24,100 years), Pu-240 (half-life: 6,560 years) and Pu-241 (half-life: 14.325 years) mainly have been released into the environment as the result of atmospheric nuclear weapons testing. The atom ratio of Pu-240/Pu-239 is a powerful fingerprint to identify the sources of Pu in the ocean. The Pu-239 and Pu-240 inventories and Pu-240/Pu-239 atom ratios in seawater samples collected in the western North Pacific off Sanriku before the accident at Fukushima Dai-ichi Nuclear Power Plant will provide useful background baseline data for understanding the process controlling Pu transport and for distinguishing additional Pu sources. Seawater samples were collected with acoustically triggered quadruple PVC sampling bottles during the KH-98-3 cruise of the R/V Hakuho-Maru. The Pu-240/Pu-239 atom ratios were measured with a double-focusing SF-ICP-MS, which was equipped with a guard electrode to eliminate secondary discharge in the plasma and to enhance overall sensitivity. The Pu-239 and Pu-240 concentrations were 2.07 and 1.67 mBq/m3 in the surface water, respectively, and increased with depth; a subsurface maximum was identified at 750 m depth, and the concentrations decreased with depth, then increased at the bottom layer. The total Pu-239+240 inventory in the entire water column (depth interval 0

A study of friction mechanisms between a surrogate skin (Lorica soft) and nonwoven fabrics.

Science.gov (United States)

Cottenden, David J; Cottenden, Alan M

2013-12-01

Hygiene products such as incontinence pads bring nonwoven fabrics into contact with users' skin, which can cause damage in various ways, including the nonwoven abrading the skin by friction. The aim of the work described here was to develop and use methods for understanding the origin of friction between nonwoven fabrics and skin by relating measured normal and friction forces to the nature and area of the contact (fibre footprint) between them. The method development work reported here used a skin surrogate (Lorica Soft) in place of skin for reproducibility. The work was primarily experimental in nature, and involved two separate approaches. In the first, a microscope with a shallow depth of field was used to determine the length of nonwoven fibre in contact with a facing surface as a function of pressure, from which the contact area could be inferred; and, in the second, friction between chosen nonwoven fabrics and Lorica Soft was measured at a variety of anatomically relevant pressures (0.25-32.1kPa) and speeds (0.05-5mms(-1)). Both techniques were extensively validated, and showed reproducibility of about 5% in length and force, respectively. Straightforward inspection of the data for Lorica Soft against the nonwovens showed that Amontons' law (with respect to load) was obeyed to high precision (R(2)>0.999 in all cases), though there was the suggestion of sub-linearity at low loads. More detailed consideration of the friction traces suggested that two different friction mechanisms are important, and comparison with the contact data suggests tentatively that they may correspond to adhesion between two different populations of contacts, one "rough" and one "smooth". This additional insight is a good illustration of how these techniques may prove valuable in studying other, similar interfaces. In particular, they could be used to investigate interfaces between nonwovens and skin, which was the primary motivation for developing them. Copyright © 2013 Elsevier Ltd

The phylogenetic relationships among germplasm resources of wild ramie (boehmeria nivea l. gaud) in china based on trnl-f and its sequences

International Nuclear Information System (INIS)

Runqing, Y.; Baloch, S.U.; Lijun, L.; Dingxiang, P.

2015-01-01

Ramie (Boehmeria nivea L. Gaud) is an important fiber crop in China, which also possesses many wild species in genus Boehmeria Jacq. However, the taxonomic position of these species has not been settled. To determine the evolutionary relationships among the members of the genus Boehmeria, the combination of ITS and trnL-F sequences were used for molecular phylogenetic analyses of 31 ramie accessions (28 species and three varieties) including multiple materials collected in high-altitude regions that have not been previously reported (B. clidemioides var. diffusa, B. bicuspis and B. longispica). The ITS and trnL-F trees produced showed that Boehmeria was classified into four separate clusters. The Sect. Duretia, which has a high evolutionary level, clustered with Sects Zoilingeriana and Phyllostachys. The grouping pattern of clustering differed from traditional taxonomy and indicated possible interspecific hybridization among Boehmeria. We found that B. malabarica Wedd. var. leioclada of Sect. Boehmeria clustered into a clade with Sect. Tilocnide, providing solid support for the expansion of wild ramie core germplasm resources. The molecular results did not support the intraspecific geographic migration of Boehmeria. This study, therefore, established relationships among wild species which will help in ramie crop improvement programs. The results will be important for the collection and conservation of germplasm resources of Chinese wild ramie. (author)

Removal of copper from acid wastewater of bioleaching by adsorption onto ramie residue and uptake by Trichoderma viride.

Science.gov (United States)

Wang, Buyun; Wang, Kai

2013-05-01

A continuous batch bioleaching was built to realize the bioleaching of sewage sludge in large scale. In the treatment, heavy metal in acid wastewater of bioleaching was removed by adsorption onto ramie residue. Then, acid wastewater was reused in next bioleaching batch. In this way, most time and water of bioleaching was saved and leaching efficiency of copper, lead and chromium kept at a high level in continuous batch bioleaching. It was found that residual heavy metal in sewage sludge is highly related to that in acid wastewater after bioleaching. To get a high leaching efficiency, concentration of heavy metal in acid wastewater should be low. Adsorption of copper from acid wastewater onto ramie residue can be described by pseudo first-order kinetics equation and Freundlich isotherm model. Trichoderma viride has the potential to be used for the concentration and recovery of heavy metal adsorbed onto ramie residue. Copyright © 2013 Elsevier Ltd. All rights reserved.

AFM characterization of nonwoven material functionalized by ZnO sputter coating

International Nuclear Information System (INIS)

Deng Bingyao; Yan Xiong; Wei Qufu; Gao Weidong

2007-01-01

Sputter coatings provide new approaches to the surface functionalization of textile materials. In this study, polyethylene terephthalate (PET) nonwoven material was used as a substrate for creating functional nanostructures on the fiber surfaces. A magnetron sputter coating was used to deposit functional zinc oxide (ZnO) nanostructures onto the nonwoven substrate. The evolution of the surface morphology of the fibers in the nonwoven web was examined using atomic force microscopy (AFM). The AFM observations revealed a significant difference in the morphology of the fibers before and after the sputter coating. The AFM images also indicated the effect of the sputtering conditions on the surface morphology of the fibers. The increase in the sputtering time led to the growth of the ZnO grains on the fiber surfaces. The higher pressure in the sputtering chamber could cause the formation of larger grains on the fiber surfaces. The higher power used also generated larger grains on the fiber surfaces

Anaerobic Biotransformation and Mobility of Pu and Pu-EDTA

International Nuclear Information System (INIS)

Bolton, H. Jr.; Rai, D.; Xun, L.

2005-01-01

The complexation of radionuclides (e.g., plutonium (Pu) and 60 Co) by codisposed ethylenediaminetetraacetate (EDTA) has enhanced their transport in sediments at DOE sites. Our previous NABIR research investigated the aerobic biodegradation and biogeochemistry of Pu(IV)-EDTA. Plutonium(IV) forms stable complexes with EDTA under aerobic conditions and an aerobic EDTA degrading bacterium can degrade EDTA in the presence of Pu and decrease Pu mobility. However, our recent studies indicate that while Pu(IV)-EDTA is stable in simple aqueous systems, it is not stable in the presence of relatively soluble Fe(III) compounds (i.e., Fe(OH) 3 (s)--2-line ferrihydrite). Since most DOE sites have Fe(III) containing sediments, Pu(IV) in likely not the mobile form of Pu-EDTA in groundwater. The only other Pu-EDTA complex stable in groundwater relevant to DOE sites would be Pu(III)-EDTA, which only forms under anaerobic conditions. Research is therefore needed in this brand new project to investigate the biotransformation of Pu and Pu-EDTA under anaerobic conditions. The biotransformation of Pu and Pu-EDTA under various anaerobic regimes is poorly understood including the reduction kinetics of Pu(IV) to Pu(III) from soluble (Pu(IV)-EDTA) and insoluble Pu(IV) as PuO2(am) by metal reducing bacteria, the redox conditions required for this reduction, the strength of the Pu(III)-EDTA complex, how the Pu(III)-EDTA complex competes with other dominant anoxic soluble metals (e.g., Fe(II)), and the oxidation kinetics of Pu(III)-EDTA. Finally, the formation of a stable soluble Pu(III)-EDTA complex under anaerobic conditions would require degradation of the EDTA complex to limit Pu(III) transport in geologic environments. Anaerobic EDTA degrading microorganisms have not been isolated. These knowledge gaps preclude the development of a mechanistic understanding of how anaerobic conditions will influence Pu and Pu-EDTA fate and transport to assess, model, and design approaches to stop Pu

Development of plasma-treated polypropylene nonwoven-based composites for high-performance lithium-ion battery separators

International Nuclear Information System (INIS)

Li, Xiaofei; He, Jinlin; Wu, Dazhao; Zhang, Mingzu; Meng, Juwen; Ni, Peihong

2015-01-01

Graphical abstract: A composite separator based on plasma-treated fluorinated polypropylene (PP) nonwoven, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and SiO 2 nanoparticles exhibiting enhanced thermal stability, ionic conductivity and electrochemical properties. Display Omitted -- Highlights: •Fluorinated segments are introduced on the surface of PP nonwoven through plasma treatment. •The obtained composite separators exhibit better physical and electrochemical properties. •The capacity of half-cell with composite separator keeps above 150 mA h g −1 after 100 charge–discharge cycles. -- Abstract: Separators have drawn substantial attention because of their important role in achieving the safety and good electrochemical performance of lithium-ion batteries. In this study, we report a new type of composite membrane prepared by a combination of fluorinated polypropylene (PP) nonwoven fabric, poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and SiO 2 nanoparticles. 2, 2, 3, 3, 4, 4, 5, 5-Octafluoropentyl methacrylate (OFPMA) is first grafted on the surface of PP nonwoven by plasma treatment to improve the nonwoven’s adhesion with PVdF-HFP. Two kinds of composite separators have been prepared by using the different PP nonwovens together with PVdF-HFP and SiO 2 nanoparticles. They were separately designated as PHS for commercially raw PP nonwoven system and PHS-n for OFPMA-modified PP nonwoven systems (n means plasma treatment time). The morphology, electrolyte uptake, ionic conductivity and electrochemical properties of the composite separators have been analyzed by scanning electron microscope (SEM) analysis, impedance measurement, charge-discharge cycle and C-rate tests, respectively. The results indicate that PHS-10 composite separator using the modified PP nonwoven treated by plasma for 10 min exhibits much better properties than PHS separator, including an improved mechanical property, thermal stability, electrolyte uptake

NKS-Norcmass reference material for analysis of Pu-isotopes and 237Np by mass spectrometry

International Nuclear Information System (INIS)

Ross, P.; Nygren, U.; Appelblad, P.; Skipperud, L.; Sjoegren, A.

2006-04-01

The aim of the reference material in the Norcmass-project was to produce a low-level ( 239 Pu) sample of sufficient amount to allow individual laboratories to perform several tests without risk of using up the material. Although there are several reference materials available (eg IAEA) few have 239 Pu/ 240 Pu data and almost none have 237 Np/ 239 Pu-data. Those who have (eg IAEA-384) have very high concentrations and are not useful for testing analytical methods designed for low-level measurements where a large sample mass may be required. The reference material consist of the top 10cm of 2mm sieved soil pooled together from 12 different Danish locations collected during 2003. The Soil was blended and sieved through 0.6 and finally through a 0.4 mm sieve. A total amount of 17 kg soil was produced. Several aliquots of the material was subject to analysis by alpha spectrometry and ICP-MS. The material contain 239 + 240 Pu at a concentration of 0.24 ± 0.01 mBq/g and a 240 Pu/ 239 Pu atom ratio of 0.19 ± 0.006. The ratio 237 Np/ 239 Pu was determined to 0.32 ± 0.01. (au)

Numerieke berekeningen aan een luchtstroming in een spleetblazer, uit het oogpunt van trekkrachtgeneratie in een nonwoven-produktieproces [Numerical computation of flow phenomena in a transport jet for the tractive power generation in a nonwoven producti

NARCIS (Netherlands)

D. Lanser (Debby)

1997-01-01

textabstractAkzo Nobel is een belangrijke producent van zgn. nonwovens of spinvliezen. Een essentiële rol in een nieuw nonwovenproduktieproces wordt gespeeld door de spleetblazer. Om de filamenten, de dunne draadjes waaruit het nonwoven is opgebouwd, te verstrekken en te transporteren, wordt in de

Non-integrability of the Armbruster-Guckenheimer-Kim quartic Hamiltonian through Morales-Ramis theory

OpenAIRE

Acosta-Humánez, P.; Alvarez-Ramírez, M.; Stuchi, T.

2017-01-01

We show the non-integrability of the three-parameter Armburster-Guckenheimer-Kim quartic Hamiltonian using Morales-Ramis theory, with the exception of the three already known integrable cases. We use Poincar\\'e sections to illustrate the breakdown of regular motion for some parameter values.

The third RAdiation transfer Model Intercomparison (RAMI) exercise: Documenting progress in canopy reflectance models

NARCIS (Netherlands)

Widlowski, J.L.; Taberner, M.; Pinty, B.; Bruniquel-Pinel, V.; Disney, M.I.; Fernandes, R.; Gastellu-Etchegorry, J.P.; Gobron, N.; Kuusk, A.; Lavergne, T.; LeBlanc, S.; Lewis, P.E.; Martin, E.; Mõttus, M.; North, P.R.J.; Qin, W.; Robustelli, M.; Rochdi, N.; Ruiloba, R.; Thompson, R.; Verhoef, W.; Verstraete, M.M.; Xie, D.

2007-01-01

[1] The Radiation Transfer Model Intercomparison ( RAMI) initiative benchmarks canopy reflectance models under well-controlled experimental conditions. Launched for the first time in 1999, this triennial community exercise encourages the systematic evaluation of canopy reflectance models on a

Developing antiviral surgical gown using nonwoven fabrics for ...

African Journals Online (AJOL)

EB

Developing antiviral surgical gown using nonwoven fabrics for health care sector. *Parthasarathi V, Thilagavathi G. Department of Fashion Technology, PSG college of Technology, Peelamedu, Coimbatore – 641 004,. India. Abstract. Background: Healthcare workers' uniforms including surgical gowns are used as barriers ...

Characterization and Properties of Electroless Nickel Plated Poly (ethylene terephthalate) Nonwoven Fabric Enhanced by Dielectric Barrier Discharge Plasma Pretreatment

International Nuclear Information System (INIS)

Geng Yamin; Lu Canhui; Liang Mei; Zhang Wei

2010-01-01

In order to develop a more economical pretreatment method for electroless nickel plating, a dielectric barrier discharge (DBD) plasma at atmospheric pressure was used to improve the hydrophilicity and adhesion of poly (ethylene terephthalate) (PET) nonwoven fabric. The properties of the PET nonwoven fabric including its liquid absorptive capacity (W A ), aging behavior, surface chemical composition, morphology of the surface, adhesion strength, surface electrical resistivity and electromagnetic interference (EMI)- shielding effectiveness (SE) were studied. The liquid absorptive capacity (W A ) increased due to the incorporation of oxygen-containing and nitrogen-containing functional groups on the surface of PET nonwoven fabric after DBD air-plasma treatment. The surface morphology of the nonwoven fibers became rougher after plasma treatment. Therefore, the surface was more prone to absorb tin sensitizer and palladium catalyst to form an active layer for the deposition of electroless nickel. SEM and X-ray diffraction (XRD) measurements indicated that a uniform coating of nickel was formed on the PET nonwoven fabric. The average EMI-SE of Ni-plating of PET nonwoven fabric maintained a relatively stable value (38.2 dB to 37.3 dB) in a frequency range of 50 MHz to 1500 MHz. It is concluded that DBD is feasible for pretreatment of nonwoven fabric for electroless nickel plating to prepare functional material with good EMI-SE properties.

Sound absorption enhancement of nonwoven felt by using coupled membrane - sonic crystal inclusion

Science.gov (United States)

Fitriani, M. C.; Yahya, I.; Harjana; Ubaidillah; Aditya, F.; Siregar, Y.; Moeliono, M.; Sulaksono, S.

2016-11-01

The experimental results from laboratory test on the sound absorption performance of nonwoven felt with an array thin tubes and sonic crystal inclusions reported in this paper. The nonwoven felt sample was produced by a local company with 15 mm in its thickness and 900 gsm. The 6.4 mm diameter plastic straw was used to construct the thin tubes array while the sonic crystal is arranged in a 4 × 4 lattice crystal formation. It made from a PVC cylinder with 17 mm and 50 mm in diameter and length respectively. All cylinders have two holes positioned on 10 mm and 25 mm from the base. The results show that both treatments, array of thin tube and sonic crystal inclusions are effectively increased the sound absorption coefficient of the nonwoven felt significantly especially in the low frequency range starting from 200Hz.

{sup 239}Pu and {sup 240}Pu inventories and {sup 240}Pu/{sup 239}Pu atom ratios in the equatorial Pacific Ocean water column

Energy Technology Data Exchange (ETDEWEB)

Yamada, Masatoshi, E-mail: myamada@cc.hirosaki-u.ac.jp [Department of Radiation Chemistry, Institute of Radiation Emergency Medicine, Hirosaki University, 66-1 Hon-cho, Hirosaki, Aomori 036-8564 (Japan); Zheng, Jian [Research Center for Radiation Protection, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage, Chiba 263-8555 (Japan)

2012-07-15

The {sup 239+240}Pu concentrations and {sup 240}Pu/{sup 239}Pu atom ratios were determined by alpha spectrometry and inductively coupled plasma mass spectrometry for seawater samples from two stations, one at the equator and the other in the equatorial South Pacific. To better understand the fate of Pu isotopes, this study dealt with the contribution of the close-in fallout Pu from the Pacific Proving Grounds (PPG) in water columns of the Pacific Ocean. The {sup 239}Pu, {sup 240}Pu and {sup 239+240}Pu inventories over the depth interval 0-3000 m at the equator station were 10.4, 8.9 and 19.3 Bq m{sup -2}, respectively. Further, no noticeable difference was observed in {sup 239}Pu, {sup 240}Pu and {sup 239+240}Pu inventories over the depth interval 0-3000 m between the two stations. The total {sup 239+240}Pu inventories were significantly higher than the expected cumulative deposition density of global fallout. Water column {sup 239+240}Pu inventories measured in this study were lower than those reported for comparable stations in the Geochemical Ocean Sections Study, indicating that these inventories have been decreasing at average rates of 0.89 {+-} 0.07 and 0.16 {+-} 0.07 Bq m{sup -2} yr{sup -1} at the equator and equatorial South Pacific stations, respectively, from 1973 to 1990. The obtained {sup 240}Pu/{sup 239}Pu atom ratios were higher than the mean global fallout ratio of 0.18. These high atom ratios proved the existence of close-in tropospheric fallout Pu from the PPG in the Marshall Islands. The {sup 239+240}Pu inventories originating from the close-in fallout in the entire water column were estimated to be 11.1 Bq m{sup -2} at the equator station and 7.1 Bq m{sup -2} at the equatorial South Pacific Ocean station, and the relative percentages of close-in fallout Pu were 40% at the former and 34% at the latter. A significant amount of close-in fallout Pu originating from the PPG has been transported to deep layers below the 1000 m depth in the equatorial

A structural model for the flexural mechanics of nonwoven tissue engineering scaffolds.

Science.gov (United States)

Engelmayr, George C; Sacks, Michael S

2006-08-01

The development of methods to predict the strength and stiffness of biomaterials used in tissue engineering is critical for load-bearing applications in which the essential functional requirements are primarily mechanical. We previously quantified changes in the effective stiffness (E) of needled nonwoven polyglycolic acid (PGA) and poly-L-lactic acid (PLLA) scaffolds due to tissue formation and scaffold degradation under three-point bending. Toward predicting these changes, we present a structural model for E of a needled nonwoven scaffold in flexure. The model accounted for the number and orientation of fibers within a representative volume element of the scaffold demarcated by the needling process. The spring-like effective stiffness of the curved fibers was calculated using the sinusoidal fiber shapes. Structural and mechanical properties of PGA and PLLA fibers and PGA, PLLA, and 50:50 PGA/PLLA scaffolds were measured and compared with model predictions. To verify the general predictive capability, the predicted dependence of E on fiber diameter was compared with experimental measurements. Needled nonwoven scaffolds were found to exhibit distinct preferred (PD) and cross-preferred (XD) fiber directions, with an E ratio (PD/XD) of approximately 3:1. The good agreement between the predicted and experimental dependence of E on fiber diameter (R2 = 0.987) suggests that the structural model can be used to design scaffolds with E values more similar to native soft tissues. A comparison with previous results for cell-seeded scaffolds (Engelmayr, G. C., Jr., et al., 2005, Biomaterials, 26(2), pp. 175-187) suggests, for the first time, that the primary mechanical effect of collagen deposition is an increase in the number of fiber-fiber bond points yielding effectively stiffer scaffold fibers. This finding indicated that the effects of tissue deposition on needled nonwoven scaffold mechanics do not follow a rule-of-mixtures behavior. These important results underscore

One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics

International Nuclear Information System (INIS)

Lin Song; Wang Zheng; Qi Jiancheng; Wu Jinhui; Tian Tao; Hao Limei; Yang Jingquan; Hou Lili

2011-01-01

Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. ε-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging.

One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics

Energy Technology Data Exchange (ETDEWEB)

Lin Song; Wang Zheng; Qi Jiancheng; Wu Jinhui; Tian Tao; Hao Limei; Yang Jingquan [Institute of Medical Equipment, Academy of Military Medical Sciences, Tianjin 300161 (China); Hou Lili, E-mail: yjq789@sohu.com [National Bio-protection Engineering Center, Tianjin 300161 (China)

2011-08-15

Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. {epsilon}-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging.

Biomass carbon micro/nano-structures derived from ramie fibers and corncobs as anode materials for lithium-ion and sodium-ion batteries

International Nuclear Information System (INIS)

Jiang, Qiang; Zhang, Zhenghao; Yin, Shengyu; Guo, Zaiping; Wang, Shiquan; Feng, Chuanqi

2016-01-01

Highlights: • Ramie fibers and corncobs are used as precursors to prepare the biomass carbons. • The ramie fiber carbon (RFC) took on morphology of 3D micro-rods. • The corncob carbon (CC) possessed a 2D nanosheets structure. • Both RFC and CC exhibited outstanding electrochemical performances in LIBs and SIBs systems. - Abstract: Three-dimensional (3D) rod-like carbon micro-structures derived from natural ramie fibers and two-dimensional (2D) carbon nanosheets derived from corncobs have been fabricated by heat treatment at 700 °C under argon atomsphere. The structure and morphology of the as-obtained ramie fiber carbon (RFC) and corncob carbon (CC) were characterized by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) technique. The electrochemical performances of the biomass carbon-based anode in lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs) were investigated. When tested as anode material for lithium ion batteries, both the RFC microrods and CC nanosheets exhibited high capacity, excellent rate capability, and stable cyclability. The specific capacity were still as high as 489 and 606 mAhg −1 after 180 cycles when cycled at room temperature in a 3.0–0.01 V potential (vs. Li/Li + ) window at current density of 100 mAg −1 , respectively, which are much higher than that of graphite (375 mAhg −1 ) under the same current density. Although the anodes in sodium ion batteries showed poorer specific capability than that in lithium-ion batteries, they still achieve a reversible sodium intercalation capacity of 122 and 139 mAhg −1 with similar cycling stability. The feature of stable cycling performance makes the biomass carbon derived from natural ramie fibers and corncobs to be promising candidates as electrodes in rechargeable sodium-ion batteries and lithium-ion batteries.

Biomass carbon micro/nano-structures derived from ramie fibers and corncobs as anode materials for lithium-ion and sodium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Jiang, Qiang; Zhang, Zhenghao [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China); Yin, Shengyu [College of Environmental and Biological Engineering, Wuhan Technology and Business University, Wuhan 430065 (China); Guo, Zaiping [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China); Institute for Superconducting & Electronic Materials, University of Wollongong, NSW 2522 (Australia); Wang, Shiquan [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China); Feng, Chuanqi, E-mail: cfeng@hubu.edu.cn [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for Synthesis and Applications of Organic Functional Molecules, Hubei University, Wuhan 430062 (China)

2016-08-30

Highlights: • Ramie fibers and corncobs are used as precursors to prepare the biomass carbons. • The ramie fiber carbon (RFC) took on morphology of 3D micro-rods. • The corncob carbon (CC) possessed a 2D nanosheets structure. • Both RFC and CC exhibited outstanding electrochemical performances in LIBs and SIBs systems. - Abstract: Three-dimensional (3D) rod-like carbon micro-structures derived from natural ramie fibers and two-dimensional (2D) carbon nanosheets derived from corncobs have been fabricated by heat treatment at 700 °C under argon atomsphere. The structure and morphology of the as-obtained ramie fiber carbon (RFC) and corncob carbon (CC) were characterized by X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) technique. The electrochemical performances of the biomass carbon-based anode in lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs) were investigated. When tested as anode material for lithium ion batteries, both the RFC microrods and CC nanosheets exhibited high capacity, excellent rate capability, and stable cyclability. The specific capacity were still as high as 489 and 606 mAhg{sup −1} after 180 cycles when cycled at room temperature in a 3.0–0.01 V potential (vs. Li/Li{sup +}) window at current density of 100 mAg{sup −1}, respectively, which are much higher than that of graphite (375 mAhg{sup −1}) under the same current density. Although the anodes in sodium ion batteries showed poorer specific capability than that in lithium-ion batteries, they still achieve a reversible sodium intercalation capacity of 122 and 139 mAhg{sup −1} with similar cycling stability. The feature of stable cycling performance makes the biomass carbon derived from natural ramie fibers and corncobs to be promising candidates as electrodes in rechargeable sodium-ion batteries and lithium-ion batteries.

Delayed Bleeding and Pelvic Haematoma after Low-Energy Osteoporotic Pubic Rami Fracture in a Warfarin Patient: An Unusual Cause of Abdominal Pain

Directory of Open Access Journals (Sweden)

Andrea Sandri

2014-01-01

Full Text Available Introduction. Acute abdominal pain may be the presenting symptom in a wide range of diseases in the elderly. Acute abdominal pain related to a delayed bleeding and pelvic haematoma after a low-energy pubic rami fracture is rare and can have important consequences; to the best of our knowledge, only one case has been previously described. Case Report. We present an unusual case of an 83-year-old woman taking warfarin for atrial fibrillation, admitted to the Emergency Department (ED with acute abdominal pain and progressive anemia related to a delayed bleeding and pelvic haematoma 72 hours after a low-energy osteoporotic pubic rami fracture. Warfarin was withheld, anticoagulation was reversed by using fresh frozen plasma and vitamin K, and concentrated red blood cells were given. Haemoglobin level gradually returned to normal with a progressive resorption of the haematoma. Conclusion. Delayed bleeding and pelvic haematoma after osteoporotic pubic rami fracture should be considered in the differential diagnosis of acute abdominal pain in the elderly. This case indicates the need for hospital admission, careful haemodynamic monitoring, and early identification of bleeding in patients with “benign” osteoporotic pubic rami fracture, especially those receiving anticoagulants, to provide an adequate management and prevent severe complications.

Noise reduction performance of thermobonded nonwovens

OpenAIRE

Carvalho, R.; Rana, S.; Fangueiro, Raúl; Soutinho, Hélder Filipe Cunha

2012-01-01

Acoustic insulation is an important requirement for the human life today, since noise affects the efficiency of day-to-day activities and even cause various health problems Materials based on fibrous structures show very good acoustic insulation properties, which however strongly depends on the type of structures used. The present paper reports the qualitative analysis of the acoustic insulation behavior of various thermo-bonded nonwoven fabrics. The results showed that the acoust...

Bleaching of hydroentangled greige cotton nonwoven fabrics without scouring

Science.gov (United States)

This work investigated whether a hydroentangled greige cotton nonwoven fabric made at a relatively high hydroentangling water pressure, say, 135-bar, could be successfully bleached to attain the desired whiteness, absorbency and other properties without traditional scouring. Accordingly, the scoured...

Biodegradation of PuEDTA and Impacts on Pu Mobility

International Nuclear Information System (INIS)

Bolton, H. Jr.; Rai, D.; Xun, L.

2004-01-01

The contamination of many DOE sites by Pu presents a long-term problem because of its long half-life (240,000 yrs) and the low drinking water standard ( -12 M). EDTA was co-disposed with radionuclides (e.g., Pu, 60 Co), formed strong complexes, and enhanced radionuclide transport at several DOE sites. Biodegradation of EDTA should decrease Pu mobility. One objective of this project was to determine the biodegradation of EDTA in the presence of PuEDTA complexes. The aqueous system investigated at pH 7 (10 -4 M EDTA and 10 -6 M Pu) contained predominantly Pu(OH) 2 EDTA 2- . The EDTA was degraded at a faster rate in the presence of Pu. As the total concentration of both EDTA and PuEDTA decreased (i.e., 10 -5 M EDTA and 10 -7 M PuEDTA), the presence of Pu decreased the biodegradation rate of the EDTA. It is currently unclear why the concentration of Pu directly affects the increase/decrease in rate of EDTA biodegradation. The soluble Pu concentration decreased, in agreement with thermodynamic predictions, as the EDTA was biodegraded, indicating that biodegradation of EDTA will decrease Pu mobility when the Pu is initially present as Pu(IV)EDTA. A second objective was to investigate how the presence of competing metals, commonly encountered in geologic media, will influence the speciation and biodegradation of Pu(IV)-EDTA. Studies on the solubilities of Fe(OH) 3 (s) and of Fe(OH) 3 (s) plus PuO 2 (am) in the presence of EDTA and as a function of pH showed that Fe(III) out competes the Pu(IV) for the EDTA complex, thereby showing that Pu(IV) will not form stable complexes with EDTA for enhanced transport of Pu in Fe(III) dominated subsurface systems. A third objective is to investigate the genes and enzymes involved in EDTA biodegradation. BNC1 can use EDTA and another synthetic chelating agent nitrilotriacetate (NTA) as sole carbon and nitrogen sources. The same catabolic enzymes are responsible for both EDTA and NTA degradation except that additional enzymes are

RAMI modeling of plant systems for proposed tritium production and extraction facilities

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

The control of life-cycle cost is a primary concern during the development, construction, operation, and decommissioning of DOE systems and facilities. An effective tool that can be used to control these costs, beginning with the design stage, is called a reliability, availability, maintainability, and inspectability analysis or, simply, RAMI for short. In 1997, RAMI technology was introduced to the Savannah River Site with applications at the conceptual design stage beginning with the Accelerator Production of Tritium (APT) Project and later extended to the Commercial Light Water Reactor (CLWR) Tritium Extraction Facility (TEF) Project. More recently it has been applied to the as-build Water Treatment Facilities designed for ground water environmental restoration. This new technology and database was applied to the assessment of balance-of-plant systems for the APT Conceptual Design Report. Initial results from the Heat Removal System Assessment revealed that the system conceptual design would cause the APT to fall short of its annual production goal. Using RAM technology to immediately assess this situation, it was demonstrated that the product loss could be gained back by upgrading the system's chiller unit capacity at a cost of less than $1.3 million. The reclaimed production is worth approximately $100 million. The RAM technology has now been extended to assess the conceptual design for the CLWR-TEF Project. More specifically, this technology and database is being used to translate high level availability goals into lower level system design requirements that will ensure the TEF meets its production goal. Results, from the limited number of system assessments performed to date, have already been used to modify the conceptual design for a remote handling system, improving its availability to the point that a redundant system, with its associated costs of installation and operation may no longer be required. RAMI results were also used to justify the elimination

Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements.

Science.gov (United States)

Xu, Yihong; Qiao, Jixin; Hou, Xiaolin; Pan, Shaoming; Roos, Per

2014-02-01

This paper reports an analytical method for the determination of plutonium isotopes ((238)Pu, (239)Pu, (240)Pu, (241)Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 × 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of (239+240)Pu by alpha spectrometry agreed very well with the sum of (239)Pu and (240)Pu measured by ICP-MS. ICP-MS can not only measure (239)Pu and (240)Pu separately but also (241)Pu. However, it is impossible to measure (238)Pu using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation. © 2013 Elsevier B.V. All rights reserved.

Multi-isotopic determination of plutonium (239Pu, 240Pu, 241Pu and 242Pu) in marine sediments using sector-field inductively coupled plasma mass spectrometry.

Science.gov (United States)

Donard, O F X; Bruneau, F; Moldovan, M; Garraud, H; Epov, V N; Boust, D

2007-03-28

Among the transuranic elements present in the environment, plutonium isotopes are mainly attached to particles, and therefore they present a great interest for the study and modelling of particle transport in the marine environment. Except in the close vicinity of industrial sources, plutonium concentration in marine sediments is very low (from 10(-4) ng kg(-1) for (241)Pu to 10 ng kg(-1) for (239)Pu), and therefore the measurement of (238)Pu, (239)Pu, (240)Pu, (241)Pu and (242)Pu in sediments at such concentration level requires the use of very sensitive techniques. Moreover, sediment matrix contains huge amounts of mineral species, uranium and organic substances that must be removed before the determination of plutonium isotopes. Hence, an efficient sample preparation step is necessary prior to analysis. Within this work, a chemical procedure for the extraction, purification and pre-concentration of plutonium from marine sediments prior to sector-field inductively coupled plasma mass spectrometry (SF-ICP-MS) analysis has been optimized. The analytical method developed yields a pre-concentrated solution of plutonium from which (238)U and (241)Am have been removed, and which is suitable for the direct and simultaneous measurement of (239)Pu, (240)Pu, (241)Pu and (242)Pu by SF-ICP-MS.

Migration of plutonium from freshwater ecosystem at Hanford. [/sup 238/Pu, /sup 239/Pu, /sup 240/Pu

Energy Technology Data Exchange (ETDEWEB)

Emery, R. M.; Klopfer, D. C.; McShane, M. C.

1977-09-01

A reprocessing waste pond at Hanford has been inventoried to determine quantities of plutonium (Pu) that have been accumulated since its formation in 1944. Expressions of export were developed from these inventory data and from informed assumptions about the vectors which act to mobilize material containing Pu. This 14-acre pond provides a realistic illustration of the mobility of Pu in a lentic ecosystem. The ecological behavior of Pu in this pond is similar to that in other contaminated aquatic systems having widely differing limnological characteristics. Since its creation, this pond has received about one Ci of /sup 239/,/sup 240/Pu and /sup 238/Pu, most of which has been retained by its sediments. Submerged plants, mainly diatoms and Potamogeton, accumulate >95% of the Pu contained in biota. Emergent insects are the only direct biological route of export, mobilizing about 5 x 10/sup 3/ nCi of Pu annually, which is also the estimated maximum quantity of the Pu exported by waterfowl, birds and mammals collectively. There is no apparent significant export by wind, and it is not likely that Pu has migrated to the ground water below U-Pond via percolation. Although this pond has a rapid flushing rate, a eutrophic nutrient supply with a diverse biotic profile, and interacts with an active terrestrial environment, it appears to effectively bind Pu and prevent it from entering pathways to man and other life.

Production of a textile reinforced concrete protective layers with non-woven polypropylene fabric

Science.gov (United States)

Žák, J.; Štemberk, P.; Vodička, J.

2017-09-01

Textile concrete with nonwoven polypropylene fabric can be used for protective layers of reinforced concrete structures, reducing the thickness of the cover layer or reducing the water penetration rate into the structure. The material consists of cement matrix with finegrained aggregate and nonwoven textile reinforcement. The maximum grain size of the mixture suitable for the nonwoven textile infiltration is 0.25 mm. The interlayer contains larger aggregates and short fibers. Tensile loading causes a large amount of microcracks in the material. The material can withstand strain over 25% without collapsing. Increased quality and water-cement ratio reduction was achieved using the plasticizers and distribution of the mixture into a fabric using a vibrating trowel. It is possible to make flat plates and even curved structures from this material. Larger curvatures of structures should be solved by cutting and overlapping the fabric. Small curvatures can be solved within the deformability of the fabric. Proper infiltration of the cement mixture into the fabric is the most important task in producing this material.

The Effects of Perlite Concentration and Coating Thickness of the Polyester Nonwoven Structures on Thermal and Acoustic Insulation and Also Electromagnetic Radiation Properties

Directory of Open Access Journals (Sweden)

Seyda EYUPOGLU

2018-02-01

Full Text Available In this study, the improvement of the thermal and acoustic insulation and also electromagnetic radiation properties of polyester (PET nonwoven fabric (NWF with 180 g/m2 weight was investigated. For this purpose, PET NWF was coated with perlite stone powder having 210 – 590 µm particle size using polyurethane (PU based coating. Five different concentrations from 1 to 5 % of perlite stone powder were applied to the surface of PET NWF having five different thicknesses. And then the effect of perlite concentration and its thickness to thermal, acoustic and electromagnetic radiation properties were studied. It was found that the addition of perlite stone powder increased the thermal and acoustic insulation properties of PET NWF. Furthermore, the addition of perlite stone powder does not affect the electromagnetic radiation properties of samples.DOI: http://dx.doi.org/10.5755/j01.ms.24.1.17562

Preparation of High Density Polyethylene/Waste Polyurethane Blends Compatibilized with Polyethylene-Graft-Maleic Anhydride by Radiation

Directory of Open Access Journals (Sweden)

Jong-Seok Park

2015-04-01

Full Text Available Polyurethane (PU is a very popular polymer that is used in a variety of applications due to its good mechanical, thermal, and chemical properties. However, PU recycling has received significant attention due to environmental issues. In this study, we developed a recycling method for waste PU that utilizes the radiation grafting technique. Grafting of waste PU was carried out using a radiation technique with polyethylene-graft-maleic anhydride (PE-g-MA. The PE-g-MA-grafted PU/high density polyethylene (HDPE composite was prepared by melt-blending at various concentrations (0–10 phr of PE-g-MA-grafted PU. The composites were characterized using fourier transform infrared spectroscopy (FT-IR, and their surface morphology and thermal/mechanical properties are reported. For 1 phr PU, the PU could be easily introduced to the HDPE during the melt processing in the blender after the radiation-induced grafting of PU with PE-g-MA. PE-g-MA was easily reacted with PU according to the increasing radiation dose and was located at the interface between the PU and the HDPE during the melt processing in the blender, which improved the interfacial interactions and the mechanical properties of the resultant composites. However, the elongation at break for a PU content >2 phr was drastically decreased.

Mechanical and thermal properties of biocomposites from nonwoven industrial Fique fiber mats with Epoxy Resin and Linear Low Density Polyethylene

Directory of Open Access Journals (Sweden)

Miguel A. Hidalgo-Salazar

2018-03-01

Full Text Available In this work Linear Low Density Polyethylene-nonwoven industrial Fique fiber mat (LLDPE-Fique and Epoxy Resin-nonwoven industrial Fique fiber mat (EP-Fique biocomposites were prepared using thermocompression and resin film infusion processes. Neat polymeric matrices and its biocomposites were tested following ASTM standards in order to evaluate tensile and flexural mechanical properties. Also, thermal behavior of these materials has been studied by differential scanning calorimetry (DSC and thermogravimetric analysis (TGA. Tensile and flexural test revealed that nonwoven Fique reinforced composites exhibited higher modulus and strength but lower deformation capability as compared with LLDPE and EP neat matrices. TG thermograms showed that nonwoven Fique fibers incorporation has an effect on the thermal stability of the composites. On the other hand, Fique fibers did not change the crystallization and melting processes of the LLDPE matrix but restricts the motion of EP macromolecules chains thus increases the Tg of the EP-Fique composite. Finally, this work opens the possibility of considering non-woven Fique fibers as a reinforcement material with a high potential for the manufacture of biocomposites for automotive applications. In addition to the processing test specimens, it was also possible to manufacture a part of LLDPE-Fique, and one part of EP-Fique. Keywords: Biocomposites, Natural materials, Nonwoven Fique fiber mat, LLDPE, Epoxy Resin

NONWOVEN TEXTILES WITH MEDICAL DESTINATION ROMANIAN PRODUCTION

Directory of Open Access Journals (Sweden)

BULACU Romulus

2015-05-01

Full Text Available The widest range of medical disposable from nonwoven textiles are: absorbent and hygiene products : (diapers, feminine care, incontinence from the layered structures absorbent or impervious; use products such as hospital operating theaters sterile clothing (caps, gowns, masks, shoe coverings, materials for field operators, lab coats, packaging materials for hot or cold treatments, sterile materials (wipes, bandages, sterile bandages, etc.. Currently these materials, in their majority, are imported. This paper presents research done for getting, with the country equipment, disposable medical products from 40 g/m2 nonwoven textile materials. The technology adopted for the purpose, in SC "Minet" S.A. Ramnicu Valcea, Romania consisted of the following steps:Carding - folding, the aggregate Spinnbau-Hergeth type, Germany, with major changes carding technology adjustment and folding, to obtain a fibrous layer with a mass per unit surface of about 40-50 g / m2 and a width of 2,1 m;Pre-heat consolidation by pre-heating required only to ensure product stability required minimal interphase transport to final consolidation. Final thermal consolidation of the fibrous layer by thermal calendering at a temperature of 110°C and calenders cylinder speed of 2 m / min. The processing of the fiber by carding - folding and preliminary thermally consolidation and final by calendering.

Design of Nonwoven Carpets to Upgrade Sound Isolation Features in Automobiles

Directory of Open Access Journals (Sweden)

Atakan Raziye

2014-12-01

Full Text Available With the increases of the expected properties of textile products, better and advanced new designs are being created. Textiles used in vehicles are increasing, and the current performance of the expectations bar is determined by automobile manufacturers. While meeting the expectations of users in the vehicle mechanically, but also disturbing the user during operation of the mechanical properties of this ratio should be minimized. This study was intended to minimize sound transmission of nonwoven textile components, which are used in cars as silencer parts. For that purpose, four different models were developed in this study. First model consists of three designs for baggage carpets. Second model has six designs for floor coverings. Third model comprises two designs inner dash felt and finally fourth model includes two designs of hood liners. The acoustical absorption coefficients and transmission loss of these carpets were tested and evaluated in the frequency range of 16-6300 Hz. The measurements demonstrated that nonwoven layer is a very significant and effective part of a carpet due to its contribution in the sound isolation. With this study, it has been determined which layer has better performance on sound absorption and transmission loss among different carpet types. A combination of heavy layer and nonwoven layer carpets is found to be benefit for noise and sound insulation.

11-year field study of Pu migration from Pu III, IV, and VI sources

International Nuclear Information System (INIS)

Kaplan, D.I.; Serkiz, S.M.; Demirkanli, D.I.; Gumapas, L.; Fjeld, R.A.; Molz, F.J.; Powell, B.A.

2005-01-01

Full text of publication follows: Understanding the processes controlling Pu mobility in the subsurface environment is important for estimating the amount of Pu waste that can be safely disposed in vadose zone burial sites. To study long-term Pu mobility, four 52-L lysimeters filled with sediment collected from the Savannah River Site near Aiken South Carolina were amended with well characterized solid Pu sources (Pu III Cl 3 , Pu IV (NO 3 ) 4 , Pu IV (C 2 O 4 ) 2 , and Pu VI O 2 (NO 3 ) 2 ) and left exposed to natural precipitation for 2 to 11 years. Pu oxidation state distribution in the Pu(III) and Pu(IV) lysimeters sediments (a red clayey sediment, pH = 6.3) were similar, consisting of 0% Pu(III), >92% Pu(IV), 1% Pu(V), 1% Pu(VI), and the remainder was a Pu polymer. These three lysimeters also had near identical sediment Pu concentration profiles, where >95% of the Pu remained within 1.25 cm of the source after 11 years; moving at an overall rate of 0.9 cm yr -1 . As expected, Pu moved more rapidly through the Pu(VI) lysimeter, at an overall rate of 12.5 cm yr -1 . Solute transport modeling of the sediment Pu concentration profile data in the Pu(VI) lysimeter indicated that some transformation of Pu into a much less mobile form, presumably Pu(IV), had occurred during the course of the two year study. This modeling also supported previous laboratory measurements showing that Pu(V) or Pu(VI) reduction was five orders of magnitude faster than corresponding Pu(III) or Pu(IV) oxidation. The slow oxidation rate (1 x 10-8 hr -1 ; t 1/2 = 8,000 yr) was not discernable from the Pu(VI) lysimeter data that reflected only two years of transport but was readily discernable from the Pu(III) and Pu(IV) lysimeter data that reflected 11 yr of transport. (authors)

²³⁹Pu and ²⁴⁰Pu inventories and ²⁴⁰Pu/²³⁹Pu atom ratios in the equatorial Pacific Ocean water column.

Science.gov (United States)

Yamada, Masatoshi; Zheng, Jian

2012-07-15

The (239+240)Pu concentrations and (240)Pu/(239)Pu atom ratios were determined by alpha spectrometry and inductively coupled plasma mass spectrometry for seawater samples from two stations, one at the equator and the other in the equatorial South Pacific. To better understand the fate of Pu isotopes, this study dealt with the contribution of the close-in fallout Pu from the Pacific Proving Grounds (PPG) in water columns of the Pacific Ocean. The (239)Pu, (240)Pu and (239+240)Pu inventories over the depth interval 0-3000 m at the equator station were 10.4, 8.9 and 19.3 Bq m(-2), respectively. Further, no noticeable difference was observed in (239)Pu, (240)Pu and (239+240)Pu inventories over the depth interval 0-3000 m between the two stations. The total (239+240)Pu inventories were significantly higher than the expected cumulative deposition density of global fallout. Water column (239+240)Pu inventories measured in this study were lower than those reported for comparable stations in the Geochemical Ocean Sections Study, indicating that these inventories have been decreasing at average rates of 0.89 ± 0.07 and 0.16 ± 0.07 Bq m(-2)yr(-1) at the equator and equatorial South Pacific stations, respectively, from 1973 to 1990. The obtained (240)Pu/(239)Pu atom ratios were higher than the mean global fallout ratio of 0.18. These high atom ratios proved the existence of close-in tropospheric fallout Pu from the PPG in the Marshall Islands. The (239+240)Pu inventories originating from the close-in fallout in the entire water column were estimated to be 11.1 Bq m(-2) at the equator station and 7.1 Bq m(-2) at the equatorial South Pacific Ocean station, and the relative percentages of close-in fallout Pu were 40% at the former and 34% at the latter. A significant amount of close-in fallout Pu originating from the PPG has been transported to deep layers below the 1000 m depth in the equatorial Pacific Ocean. Copyright © 2012 Elsevier B.V. All rights reserved.

Method for producing bonded nonwoven fabrics using ionizing radiation

International Nuclear Information System (INIS)

Drelich, A.H.; Oney, D.G.

1979-01-01

A method is described for producing a resin-bonded nonwoven fabric. The preparation involves forming a fibrous web annealing it and compressing it to provide fiber to fiber contact. A polymerizable binder is applied to the fibrous web which is then treated by ionizing radiation to produce the material. 9 figures, 3 drawing

Use of 236Pu and 242Pu as a radiochemical tracer for estimation of Pu in bioassay samples by fission track analysis

International Nuclear Information System (INIS)

Sawant, Pramilla D.; Prabhu, Supreetha P.; Kalsi, P.C.

2008-01-01

236 Pu and 242 Pu are routinely used as radiochemical yield monitors in India for bioassay monitoring of occupational workers by alpha spectrometry. Fission Track Analysis (FTA) is also being standardized for trace level determination of Pu in bioassay samples. The present study, reports the utility of 236 Pu and 242 Pu as radiochemical tracers in estimation of Pu in bioassay samples by FTA technique. The advantages of using 236 Pu tracer in FTA over 242 Pu as well as the interference caused due to presence of 241 Pu in the bioassay samples of occupational workers handling power reactor grade Pu is discussed. (author)

RAMI analysis for DEMO HCPB blanket concept cooling system

Energy Technology Data Exchange (ETDEWEB)

Dongiovanni, Danilo N., E-mail: danilo.dongiovanni@enea.it [ENEA, Unità Tecnica Fusione, ENEA C. R. Frascati (Italy); Pinna, Tonio [ENEA, Unità Tecnica Fusione, ENEA C. R. Frascati (Italy); Carloni, Dario [KIT, Institute of Neutron Physics and Reactor Technology (INR) – KIT (Germany)

2015-10-15

Highlights: • RAMI (reliability, availability, maintainability and inspectability) preliminary assessment for HCPB blanket concept cooling system. • Reliability block diagram (RBD) modeling and analysis for HCPB primary heat transfer system (PHTS), coolant purification system (CPS), pressure control system (PCS), and secondary cooling system. • Sensitivity analysis on system availability performance. • Failure models and repair models estimated on the base of data from the ENEA fusion component failure rate database (FCFRDB). - Abstract: A preliminary RAMI (reliability, availability, maintainability and inspectability) assessment for the HCPB (helium cooled pebble bed) blanket cooling system based on currently available design for DEMO fusion power plant is presented. The following sub-systems were considered in the analysis: blanket modules, primary cooling loop including pipework and steam generators lines, pressure control system (PCS), coolant purification system (CPS) and secondary cooling system. For PCS and CPS systems an extrapolation from ITER Test Blanket Module corresponding systems was used as reference design in the analysis. Helium cooled pebble bed (HCPB) system reliability block diagrams (RBD) models were implemented taking into account: system reliability-wise configuration, operating schedule currently foreseen for DEMO, maintenance schedule and plant evolution schedule as well as failure and corrective maintenance models. A simulation of plant activity was then performed on implemented RBDs to estimate plant availability performance on a mission time of 30 calendar years. The resulting availability performance was finally compared to availability goals previously proposed for DEMO plant by a panel of experts. The study suggests that inherent availability goals proposed for DEMO PHTS system and Tokamak auxiliaries are potentially achievable for the primary loop of the HCPB concept cooling system, but not for the secondary loop. A

EL COLAPSO DEL CLÁSICO TARDÍO ENTRE LOS MAYAS DE UAXACTÚN (GUATEMALA Y BARTON RAMIE (BELICE SEGÚN EL REGISTRO FUNERARIO (The Late Classic Collapse among the Maya of Uaxactun, Guatemala and Barton Ramie, Belize according to the Mortuary Record

Directory of Open Access Journals (Sweden)

Pascual Izquierdo-Egea

2015-09-01

Full Text Available La aplicación del método de valoración contextual al análisis del registro funerario de Uaxactún (Guatemala y Barton Ramie (Belice aporta evidencias irrefutables sobre la huella material del colapso clásico en las ofrendas de los entierros mayas. Esto confirma lo que ya se había anticipado al estudiar la cuenca del río Balsas en México (2014. ENGLISH: Application of the contextual valuation method to the mortuary analysis of Uaxactun, Guatemala and Barton Ramie, Belize provides irrefutable evidence on the Classic Maya collapse recorded in the grave goods of these burials. This confirms what was already anticipated by studying the Balsas River basin in Mexico.

Pu(IV) reduction with hydroxyurea and its application in U/Pu separation

International Nuclear Information System (INIS)

Zhu Zhaowu; He Jianyu; Zhang Zefu; Song Tianbao; Zhang Yu; Zheng Weifang

2004-01-01

The reduction of Pu(IV) with hydroxyurea (HU) in the mixed phase of 30% TBP/OK-HNO 3 system was studied. The study results show that HU can reduce Pu(IV) to Pu(III) and the reduction rate can be expressed as -dc(Pu(IV))/dt=kc(HU)c -3.2 (HNO 3 )c mix 2 (Pu(IV))c mix -1 (Pu(III)), where k is the rate constant, and k=(896 ± 59) mol 2.3 ·L -2.3 ·min -1 at 15 degree C. With HU serves as a reductant, 16 stages count-current cascade experiment was performed using centrifugal tube to simulate U/Pu separation in the 1B contactor of Purex process. The separation factor of Pu from U and the separation factor of U from Pu reach to 5.4 x 10 4 and 1.8 x 10 5 , respectively. The amount of Pu is about 11 μg in per kg U product. (authors)

Direct spectrophotometric analysis of low level Pu (III) in Pu(IV) nitrate solution

International Nuclear Information System (INIS)

Mageswaran, P.; Suresh Kumar, K.; Kumar, T.; Gayen, J.K.; Shreekumar, B.; Dey, P.K.

2010-01-01

Among the various methods demonstrated for the conversion of plutonium nitrate to its oxide, the oxalate precipitation process either as Pu (III) or Pu (IV) oxalate gained wide acceptance. Since uranous nitrate is the most successful partitioning agent used in the PUREX process for the separation of Pu from the bulk amount of U, the Pu (III) oxalate precipitation of the purified nitrate solution will not give required decontamination from U. Hence Pu IV oxalate precipitation process is a better option to achieve the end user's specified PuO 2 product. Prior to the precipitation process, ensuring of the Pu (IV) oxidation state is essential. Hence monitoring of the level of Pu oxidation state either Pu (III) or Pu (IV) in the feed solution plays a significant role to establish complete conversion of Pu (III). The method in vogue to estimate Pu(lV) content is extractive radiometry using Theonyl Trifluoro Acetone (TTA). As the the method warrants a sample preparation with respect to acidity, a precise measurement of Pu (IV) without affecting the Pu(III) level in the feed sample is difficult. Present study is focused on the exploration of direct spectrophotometry using an optic fiber probe of path length of 40mm to monitor the low level of Pu(III) after removing the bulk Pu(lV) which interfere in the Pu(III) absorption spectrum, using TTA-TBP synergistic mixture without changing the sample acidity

High energy ballistic and fracture comparison between multilayered armor systems using non-woven curaua fabric composites and aramid laminates

Directory of Open Access Journals (Sweden)

Fábio de Oliveira Braga

2017-10-01

Full Text Available For personal protection against high kinetic energy projectiles, multilayered armor systems (MAS are usually the best option. They combine synergistically the properties of different materials such as ceramics, composites and metals. In the present work, ballistic tests were performed to evaluate multilayered armor systems (MAS using curaua non-woven fabric epoxy composites as second layer. A comparison to a MAS using aramid (Kevlar™ fabric laminates was made. The results showed that the curaua non-woven fabric composites are suitable to the high ballistic applications, and are promising substitutes for aramid fabric laminates. Keywords: Composite, Natural fiber, Curaua fiber, Non-woven fabric, Aramid laminate, Ballistic test

A procedure for identifying textile bast fibres using microscopy: Flax, nettle/ramie, hemp and jute

International Nuclear Information System (INIS)

Bergfjord, Christian; Holst, Bodil

2010-01-01

Identifying and distinguishing between natural textile fibres is an important task in both archaeology and criminology. Wool, silk and cotton fibres can readily be distinguished from the textile bast fibres flax, nettle/ramie, hemp and jute. Distinguishing between the bast fibres is, however, not easily done and methods based on surface characteristics, chemical composition and cross section size and shape are not conclusive. A conclusive method based on X-ray microdiffraction exists, but as the method requires the use of a synchrotron it is not readily available. In this paper we present a simple procedure for identifying the above mentioned textile bast fibres. The procedure is based on measuring the fibrillar orientation with polarised light microscopy and detecting the presence of calcium oxalate crystals (CaC 2 O 4 ) in association with the fibres. To demonstrate the procedure, a series of fibre samples of flax, nettle, ramie, hemp and jute were investigated. The results are presented here. An advantage of the procedure is that only a small amount of fibre material is needed.

A procedure for identifying textile bast fibres using microscopy: Flax, nettle/ramie, hemp and jute

Energy Technology Data Exchange (ETDEWEB)

Bergfjord, Christian, E-mail: christian.bergfjord@uib.no [Institute for Physics and Technology, University of Bergen, Allegt. 55, 5007 Bergen (Norway); Holst, Bodil, E-mail: bodil.holst@uib.no [Institute for Physics and Technology, University of Bergen, Allegt. 55, 5007 Bergen (Norway)

2010-08-15

Identifying and distinguishing between natural textile fibres is an important task in both archaeology and criminology. Wool, silk and cotton fibres can readily be distinguished from the textile bast fibres flax, nettle/ramie, hemp and jute. Distinguishing between the bast fibres is, however, not easily done and methods based on surface characteristics, chemical composition and cross section size and shape are not conclusive. A conclusive method based on X-ray microdiffraction exists, but as the method requires the use of a synchrotron it is not readily available. In this paper we present a simple procedure for identifying the above mentioned textile bast fibres. The procedure is based on measuring the fibrillar orientation with polarised light microscopy and detecting the presence of calcium oxalate crystals (CaC{sub 2}O{sub 4}) in association with the fibres. To demonstrate the procedure, a series of fibre samples of flax, nettle, ramie, hemp and jute were investigated. The results are presented here. An advantage of the procedure is that only a small amount of fibre material is needed.

Mechanical and thermal properties of biocomposites from nonwoven industrial Fique fiber mats with Epoxy Resin and Linear Low Density Polyethylene

Science.gov (United States)

Hidalgo-Salazar, Miguel A.; Correa, Juan P.

2018-03-01

In this work Linear Low Density Polyethylene-nonwoven industrial Fique fiber mat (LLDPE-Fique) and Epoxy Resin-nonwoven industrial Fique fiber mat (EP-Fique) biocomposites were prepared using thermocompression and resin film infusion processes. Neat polymeric matrices and its biocomposites were tested following ASTM standards in order to evaluate tensile and flexural mechanical properties. Also, thermal behavior of these materials has been studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Tensile and flexural test revealed that nonwoven Fique reinforced composites exhibited higher modulus and strength but lower deformation capability as compared with LLDPE and EP neat matrices. TG thermograms showed that nonwoven Fique fibers incorporation has an effect on the thermal stability of the composites. On the other hand, Fique fibers did not change the crystallization and melting processes of the LLDPE matrix but restricts the motion of EP macromolecules chains thus increases the Tg of the EP-Fique composite. Finally, this work opens the possibility of considering non-woven Fique fibers as a reinforcement material with a high potential for the manufacture of biocomposites for automotive applications. In addition to the processing test specimens, it was also possible to manufacture a part of LLDPE-Fique, and one part of EP-Fique.

E-Learning as an Important Component in “Blended Learning” in School Development Projects in Norway

OpenAIRE

Aasen, Ann Margareth

2013-01-01

E-learning is an important component in ཿblended learning࿝ in all of SePU`s projects and is used for additional education and development of competences. Blended learning is defined as learning facilitated by the effective combination of different modes of delivery, models of teaching, styles of learning, and based on transparent communication among all parties involved in development competences. In general, one of the challenges with improving the workplace is linked to employee training an...

Environmentally friendly and breathable wet-laid hydroentangled nonwovens for personal hygiene care with excellent water absorbency and flushability

Science.gov (United States)

Deng, Chao; Liu, Wanjun; Zhang, Yinjiang; Huang, Chen; Zhao, Yi; Jin, Xiangyu

2018-04-01

Developing wet-laid papers with a good wet strength remains a longstanding challenge in the papermaking industry. In this study, hydroentanglement, a mechanical bonding technique is developed to consolidate the wet-laid fibre web. The results indicate that wet tensile strength, ductile stretching property, softness, air permeability and water absorbency of the wet-laid fibre web are significantly improved by hydroentanglement. In addition, the abrasion test shows that the dusting off rate of wet-laid fibre web can be effectively reduced through hydroentanglement. Moreover, the disintegration experiment proves that wet-laid hydroentangled nonwovens could be easily dispersed when compared with conventional carded hydroentangled nonwovens. Therefore, the new wet-laid hydroentangled nonwovens can maintain excellent performance in a wet state, showing a great potential for personal hygiene applications.

Trapping of polycyclic aromatic hydrocarbons by amphiphilic cyclodextrin functionalized polypropylene nonwovens

DEFF Research Database (Denmark)

Lumholdt, Ludmilla; Nielsen, Ronnie Bo Højstrup; Larsen, Kim Lambertsen

of the textile fibers. In this study we present the ability of amphiphilic CD coated polypropylene nonwovens to trap 8 different polycyclic aromatic hydrocarbons/endocrine disruptors from aqueous solutions thus demonstrating the potential of using the amphiphilic cyclodextrins for water purification....

Enhancement of the thermal and mechanical properties of polyurethane/polyvinyl chloride blend by loading single walled carbon nanotubes

Directory of Open Access Journals (Sweden)

A.M. Hezma

2017-06-01

Full Text Available Structural, thermal, and mechanical properties of pure blend and nanocomposites based on polyurethane (PU and polyvinyl chloride (PVC doped with low different content of single walled-carbon nanotubes (SWCNTs were studied. The nanocomposites at different concentration were prepared via casting technique. The interaction between PU/PVC and CNTs were examined via FT-IR studies. The changes in the structures of the nanocomposites were examined using X- Ray Diffraction (XRD, and the results indicated that the amorphous domains of nanocomposites increased with increasing SWCNTs content. Transmission electron microscope (TEM observation indicated that SWCNTs surface was wrapped with the polymer with the thermal properties of nanocomposites improved. The mechanical behavior of the nanocomposites was evaluated as a function of SWCNTs content. The main enhancement in tensile properties was observed, e.g., the tensile strength and elastic modulus increased compared with the pure blend, which may be attributed to the interaction and adhesion between CNTs and the polymer matrices due to the hydrogen bonding between carbonyl groups (C=O of polymer blend chains and carboxylic acid (COOH groups of CNTs.

Assessment of poly(ε-caprolactone)/poly(3-hydroxybutyrate-co-3-hydroxyvalerate) blends processed by solvent casting and electrospinning

International Nuclear Information System (INIS)

Del Gaudio, Costantino; Ercolani, Enrico; Nanni, Francesca; Bianco, Alessandra

2011-01-01

Research highlights: → PHBV, PCL and blends were processed in form of solvent cast films and e-spun mats. → A clear phase separation was observed for cast films when blended in equal amount. → E-spun blends were comprised of uniform and defect-free randomly arranged fibers. → DSC and XRD analyses demonstrated the immiscibility of PHBV and PCL. → Rearrangement of e-spun fibers and neckings, after axial test, were observed. - Abstract: Poly(ε-caprolactone) (PCL) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) were blended in different ratio, e.g. 30/70, 50/50 and 70/30 (w/w), by means of solvent casting or electrospinning. Microstructure, thermal and mechanical properties of cast films and non-woven mats were investigated by means of scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), differential scanning calorimetry (DSC), and uniaxial tensile test. The microstructure of PHBV/PCL solvent cast films (thickness 65-100 μm) was strictly dependent on the composition of the blend, a clean phase separation was observed for the 50/50 (w/w) sample. All electrospun PHBV/PCL blends (thickness 350-800 μm) were characterised by uniform and homogenous fibers, the average size was about 3 μm. Both techniques led to polymeric blends comprised of separate crystalline domains associated to an amorphous interdisperse phase. It has also been demonstrated that electrospun PHBV/PCL blends showed a lower segregation degree among the crystalline domains. Solvent cast blends were characterised by superior mechanical properties in terms of tensile modulus and tensile strength compared to electrospun ones. Fractured electrospun blends showed an overall fiber rearrangement in the direction of the applied load, eventually highlighting multiple necking regions along the fibers.

Structure/function relations of hemostatic nonwoven dressings based on greige cotton

Science.gov (United States)

A variety of natural and synthetic fibers are employed in hemostatic dressings. Here we demonstrate the use of greige cotton as a functional fiber, which when combined with hydrophilic and hydrophobic fibers in hydroentangled nonwoven materials, promotes accelerated clotting. A biophysical approach...

High Efficiency Particulate Air (HEPA) filters from polyester and polypropylene fibre nonwovens

CSIR Research Space (South Africa)

Boguslavsky, L

2010-10-01

Full Text Available filtration efficiency. Glass fibres are more harmful to human, compared to polypropylene and polyester fibre which are chemically inert. Hydroentanglement and chemical bonding techniques were utilised in manufacturing nonwovens for dry filtration. Acrylic...

Potential application of microporous structured poly(vinylidene fluoride-hexafluoropropylene)/poly(ethylene terephthalate) composite nonwoven separators to high-voltage and high-power lithium-ion batteries

International Nuclear Information System (INIS)

Jeong, Hyun-Seok; Choi, Eun-Sun; Kim, Jong Hun; Lee, Sang-Young

2011-01-01

Highlights: → Microporous-structured PVdF-HFP/PET composite nonwoven separators for Li-batteries. → Well-developed microporous structure and liquid electrolyte wettability. → Provision of facile ion transport and suppressed growth of cell impedance. → Superior cell performance at high-voltages/high-current densities. - Abstract: We demonstrate potential application of a new composite non-woven separator, which is comprised of a phase inversion-controlled, microporous polyvinylidene fluoride-hexafluoropropylene (PVdF-HFP) gel polymer electrolyte and a polyethylene terephthalate (PET) non-woven support, to high-voltage and high-power lithium-ion batteries. In comparison to a commercialized polyethylene (PE) separator, the composite non-woven separator exhibits distinct improvements in microporous structure and liquid electrolyte wettability. Based on the understanding of the composite non-woven separator, cell performances of the separator at challenging charge/discharge conditions are investigated and discussed in terms of ion transport of the separator and AC impedance of the cell. The aforementioned advantageous features of the composite non-woven separator play a key role in providing facile ion transport and suppressing growth of cell impedance during cycling, which in turn contribute to superior cell performances at harsh charge/discharge conditions such as high voltages and high current densities.

Analysis of plutonium isotope ratios including 238Pu/239Pu in individual U-Pu mixed oxide particles by means of a combination of alpha spectrometry and ICP-MS.

Science.gov (United States)

Esaka, Fumitaka; Yasuda, Kenichiro; Suzuki, Daisuke; Miyamoto, Yutaka; Magara, Masaaki

2017-04-01

Isotope ratio analysis of individual uranium-plutonium (U-Pu) mixed oxide particles contained within environmental samples taken from nuclear facilities is proving to be increasingly important in the field of nuclear safeguards. However, isobaric interferences, such as 238 U with 238 Pu and 241 Am with 241 Pu, make it difficult to determine plutonium isotope ratios in mass spectrometric measurements. In the present study, the isotope ratios of 238 Pu/ 239 Pu, 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu were measured for individual Pu and U-Pu mixed oxide particles by a combination of alpha spectrometry and inductively coupled plasma mass spectrometry (ICP-MS). As a consequence, we were able to determine the 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu isotope ratios with ICP-MS after particle dissolution and chemical separation of plutonium with UTEVA resins. Furthermore, 238 Pu/ 239 Pu isotope ratios were able to be calculated by using both the 238 Pu/( 239 Pu+ 240 Pu) activity ratios that had been measured through alpha spectrometry and the 240 Pu/ 239 Pu isotope ratios determined through ICP-MS. Therefore, the combined use of alpha spectrometry and ICP-MS is useful in determining plutonium isotope ratios, including 238 Pu/ 239 Pu, in individual U-Pu mixed oxide particles. Copyright © 2016 Elsevier B.V. All rights reserved.

Hierarchical Chitin Fibers with Aligned Nanofibrillar Architectures: A Nonwoven-Mat Separator for Lithium Metal Batteries.

Science.gov (United States)

Kim, Joong-Kwon; Kim, Do Hyeong; Joo, Se Hun; Choi, Byeongwook; Cha, Aming; Kim, Kwang Min; Kwon, Tae-Hyuk; Kwak, Sang Kyu; Kang, Seok Ju; Jin, Jungho

2017-06-27

Here, we introduce regenerated fibers of chitin (Chiber), the second most abundant biopolymer after cellulose, and propose its utility as a nonwoven fiber separator for lithium metal batteries (LMBs) that exhibits an excellent electrolyte-uptaking capability and Li-dendrite-mitigating performance. Chiber is produced by a centrifugal jet-spinning technique, which allows a simple and fast production of Chibers consisting of hierarchically aligned self-assembled chitin nanofibers. Following the scrutinization on the Chiber-Li-ion interaction via computational methods, we demonstrate the potential of Chiber as a nonwoven mat-type separator by monitoring it in Li-O 2 and Na-O 2 cells.

Pre-irradiation induced emulsion graft polymerization of acrylonitrile onto polyethylene nonwoven fabric

International Nuclear Information System (INIS)

Liu Hanzhou; Yu Ming; Deng Bo; Li Linfan; Jiang Haiqing; Li Jingye

2012-01-01

Acrylonitrile has been widely used in the modification of polymers by graft polymerization. In the present work, pre-irradiation induced emulsion graft polymerization method is used to introduce acrylonitrile onto PE nonwoven fabric instead of the traditional reaction in organic solvents system. The degree of grafting (DG) is measured by gravimetric method and the kinetics of the graft polymerization is studied. The existence of the graft chains is proven by Fourier transform infrared spectroscopy (FT-IR) analysis. Thermal stability of the grafted polymer is measured by Thermogravimetric analysis (TGA). - Highlights: → Acrylonitrile is grafted onto pre-irradiated polyethylene (PE) nonwoven fabrics. → Emulsion system is applied, for the graft polymerization avoids organic solvent. → Kinetic of the pre-irradiation induced graft polymerization is studied. → Optimal condition is determined at the temperature below the b.p. of acrylonitrile.

Migration behaviour of Pu released from Pu-doped glass in compacted bentonite

International Nuclear Information System (INIS)

Ashida, T.; Kohara, Y.; Yui, M.

1994-01-01

In order to investigate the coupled behavior of Pu release from the waste glass and transport in bentonite, a migration experiment with compacted sodium-type bentonite saturated with distilled water was carried out at room temperature, in which Pu-doped borosilicate glass was sandwiched. Under these conditions, leaching of Pu from the glass, diffusion and sorption of Pu in the compacted bentonite occur simultaneously. (orig.)

Characterization by Suppression Subtractive Hybridization of Transcripts That Are Differentially Expressed in Leaves of Anthracnose-Resistant Ramie Cultivar.

Science.gov (United States)

Xuxia, Wang; Jie, Chen; Bo, Wang; Lijun, Liu; Hui, Jiang; Diluo, Tang; Dingxiang, Peng

2012-01-01

For the purpose of screening putative anthracnose resistance-related genes of ramie ( Boehmeria nivea L. Gaud), a cDNA library was constructed by suppression subtractive hybridization using anthracnose-resistant cultivar Huazhu no. 4. The cDNAs from Huazhu no. 4, which were infected with Colletotrichum gloeosporioides , were used as the tester and cDNAs from uninfected Huazhu no. 4 as the driver. Sequencing analysis and homology searching showed that these clones represented 132 single genes, which were assigned to functional categories, including 14 putative cellular functions, according to categories established for Arabidopsis . These 132 genes included 35 disease resistance and stress tolerance-related genes including putative heat-shock protein 90, metallothionein, PR-1.2 protein, catalase gene, WRKY family genes, and proteinase inhibitor-like protein. Partial disease-related genes were further analyzed by reverse transcription PCR and RNA gel blot. These expressed sequence tags are the first anthracnose resistance-related expressed sequence tags reported in ramie.

Electrolyte influence on sorption behaviours of Direct Blue 71 dye on ramie fibre

Directory of Open Access Journals (Sweden)

Yuan Chi

2017-01-01

Full Text Available Ramie loose fibre was dyed using Direct Blue 71 dye at 70, 80, 90 and 100°C without and with NaCl electrolyte in order to investigate the distinction of dye sorption behaviours. The results show that the dye exhaustion increases with addition of NaCl and shortens the equilibrium dyeing time. The dye adsorption process of dyeing without and with NaCl followed pseudo second-order kinetics, but the rate constant of sorption is larger for the latter compared to the former.

Solubility of reactor fuels in the mouse lung with respect to their U/Pu and 238Pu/239Pu ratios

International Nuclear Information System (INIS)

Talbot, R.J.; Baker, S.T.

1989-01-01

The studies reported were designed to assess the comparative in vivo solubilities of a range of plutonium containing reactor fuels. To simulate these fuels, mixed U/Pu oxides were prepared and calcined at 1600 0 C. A plutonium content of 3% w/w was chosen as typical of water-cooled reactor fuel. Higher concentrations of plutonium (10, 20 and 30%) were included to simulate fast reactor fuel. As it is known that 238 PuO 2 , with high specific activity, is translocated more rapidly from lung than 239 PuO 2 , the effect of isotopic composition of plutonium in simulated reactor fuels was also investigated. For this purpose, both the water-cooled and fast-reactor fuels were prepared with plutonium containing 2% of 238 Pu by weight. The resulting oxides had about 6 times the specific activity of those prepared with 239 Pu. Groups of mice were killed at 1, 3, 6, 12 and 18 months after inhaling aerosols of the simulated reactor fuels. After 3 months, measurements of Pu retention in the lung showed no marked differences between materials. After 6 months, measurements of plutonium deposited in the liver and skeleton showed that mixed U/Pu oxides were more soluble in vivo than 239 PuO 2 . Their solubility was inversely related to their plutonium content. The addition of 238 Pu to the plutonium resulted in enhanced translocation of plutonium from the lung, in the cases of water-cooled reactor fuel by a factor of two. (author)

Raman spectrometric determination of Pu(VI) and Pu(V) in nitric acid solutions

International Nuclear Information System (INIS)

Gantner, E.; Freudenberger, M.; Steinert, D.; Ache, H.J.

1987-03-01

The determination of Pu(VI) in nitric acid solutions by spontaneous Laser Raman Spectrometry (LRS) was investigated and a calibration curve was established using U(VI) as internal standard. In addition, the concentrations of Pu(VI) and Pu(V) as a function of time were measured by this method in Pu(VI) solutions of different acidity containing H 2 O 2 as the reducing agent. In solutions which are intensely coloured by the presence of Ru(NO) complexes Pu(VI) can also be determined by LRS using a Kr + laser as excitation source. In future experiments, the study of the Pu(IV)-interaction with Ru using LRS and spectrophotometry as analytical techniques is therefore intended. (orig.) [de

Isotope ratios of 240Pu/239Pu in soil samples from different areas

International Nuclear Information System (INIS)

Muramatsu, Yasuyuki; Yoshida, Satoshi; Yamazaki, Shinnosuke

2003-01-01

Plutonium concentrations and 240 Pu/ 239 Pu atom ratios in soil samples from Japan and other areas in the world (including IAEA standard reference materials) were determined by ICP-MS. The range of 240 Pu/ 239 Pu atom ratios observed in 21 Japanese soil samples was 0.155 - 0.194 and the average was 0.180 ± 0.011, which is comparable to the global fallout value. A low ratio of about 0.05, which is derived from Pu-bomb, was found in samples from Nishiyama (Nagasaki) and Mururoa Atoll (IAEA-368), while a high ratio of about 0.31 was found in a sample from Bikini Atoll (Marshall Islands). The ratio for Irish Sea sediment (IAEA-135) was 0.21, which was higher than the global fallout value, suggesting the influence by the contamination from the Sellafield facility. The 240 Pu/ 239 Pu atom ratios in soils from the Chernobyl area were determined, and the ratio was found to be very high (about 0.4), indicating the high burn-up grade of the reactor fuel. These results show that the 240 Pu/ 239 Pu ratio can be used as a finger print to identify the source of the contamination. (author)

Quantitative Assay of Pu-239 and Pu-240 by Neutron Transmission Measurements

Energy Technology Data Exchange (ETDEWEB)

Johansson, E

1971-04-15

A method for quantitative assay of 239Pu and 240Pu has been tested at the reactor R1 in Stockholm. The method makes use of a fast chopper to measure the neutron transmission through a sample around the main resonances of these two isotopes - at 0.296 eV in 239Pu and at 1.056 eV in 240Pu. The transmission data measured are then combined with the known resonance cross sections to give the content of the isotopes. The method is nondestructive, i.e., one can use fuel pins as samples, even highly irradiated ones. A time-of-flight spectrometer of moderate capacity, like our fast chopper, is sufficient as the resonances are located at low energy. Altogether five samples have been used in the tests of the method. The results have been compared with mass spectrometer values. This comparison came out quite well for 239Pu whereas the chopper results for 240Pu were more than 10 per cent higher than the mass spectrometer results. This large deviation might be due to errors in the resonance cross section for 240Pu used in the analysis of the transmission data from the chopper. The best possible accuracy for a 15-hour run with our equipment is +- 1 per cent for 239Pu and +- 2 per cent for 240Pu, obtained for thick samples - about 3 x 1020 atoms per cm2 for each isotope. The accuracy corresponds to 68 per cent confidence level and does not include any contribution from the uncertainty in the resonance cross section

Determination of {sup 240}Pu/{sup 239}Pu ratio and its significance in environmental studies

Energy Technology Data Exchange (ETDEWEB)

Muramatsu, Yasuyuki [National Inst. of Radiological Sciences, Chiba (Japan)

1999-03-01

Analytical procedures for the determination of Pu concentrations and its isotopic ratios in environmental samples were developed by using ICP-MS. Detection limit of Pu by ICP-MS was about 0.02 pg ml{sup -1} (0.05 mBq ml{sup -1} for {sup 239}Pu; 0.17 mBq ml{sup -1} for {sup 240}Pu) in the sample solution. Analytical results of {sup 239+240}Pu in IAEA standard reference materials indicated that the accuracy of this method was satisfactory. Data on the {sup 240}Pu/{sup 239}Pu atom ratios, which are rare in the literature, were also obtained for soil and sediment samples (including IAEA standard reference materials) from different areas such as Irish Sea, Mururoa Atoll, Marshall Islands, Chernobyl, Kyshtym, Nagasaki and some other places in Japan. The range of the {sup 240}Pu/{sup 239}Pu ratios was about 0.04-0.4, and the ratios are depending on the origin of the materials. Analytical results for the {sup 240}Pu/{sup 239}Pu atom ratios provide information about the source of the contamination and the transfer of plutonium in the environment. (author)

Simultaneous measurement of 239Pu, 240Pu, 241Pu, and 242Pu by high resolution inductively coupled plasma mass spectrometer (HR ICP-MS) in marine sediments

International Nuclear Information System (INIS)

Bruneau, F.

1999-01-01

Transuranics elements are of particular interest in radioecological studies because of their radiotoxicity and their potential use to decipher source fingerprints and transport processes. The simultaneous measurement of 239 Pu, 240 Pu, 241 Pu, and 242 Pu in environmental samples requires a specific chemical procedure. This work deals with an analytical procedure which yields a very high grade of purification of Pu suitable for ultra low level detection by HR ICP-MS, from marine sediments. After the elimination of major elements (Fe, Al, Mg...) by a first chromatographic separation, a new device of purification by solvent extraction and concentration by a second chromatographic separation is used to obtain a concentrated and high purified solution of plutonium. The chemical procedure have been validated on IAEA certified sediment samples and on sediment samples collected in the roads of Cherbourg which had been previously analysed by other techniques (a spectrometry and thermo-ionisation mass spectrometer). (author)

Fermiology of PuCoGa{sub 5} and of related Pu-115 compounds

Energy Technology Data Exchange (ETDEWEB)

Oppeneer, P.M. [Department of Physics, Box 530, Uppsala University, S-751 21 Uppsala (Sweden)], E-mail: peter.oppeneer@fysik.uu.se; Shick, A.B. [Institute of Physics, Academy of Sciences of the Czech Republic, CZ-18221 Prague (Czech Republic); Rusz, J. [Department of Electronic Structures, Faculty of Mathematics and Physics, Charles University, Ke Karlovu 5, CZ-121 16 Prague 2 (Czech Republic); Lebegue, S. [Laboratoire de Cristallographie et de Modelisation des Materiaux Mineraux et Biologiques, CNRS-Universite Henri Poincare, B.P. 239, F-54506 Vandoeuvre-les-Nancy (France); Eriksson, O. [Department of Physics, Box 530, Uppsala University, S-751 21 Uppsala (Sweden)

2007-10-11

We report computational investigations of the electronic structures of the superconducting Pu-compounds PuCoGa{sub 5} as well as of the non-superconducting compounds PuFeGa{sub 5} and PuNiGa{sub 5}. To capture the localization behavior of the Pu 5f electrons, we apply two computational approaches, which are both rooted in the density-functional theory: the local spin-density approximation (LSDA) and the around mean field (AMF) LSDA+U approach. The latter is applicable to moderately localized 5f electrons while the former is applicable to delocalized 5f electrons. Our LSDA calculations show that the Fermi surfaces of the three Pu-115 compounds are sensitive to the amount of band filling, i.e., the number of electrons of the 3d element. Precisely at the electron filling corresponding to PuCoGa{sub 5} the Fermi surface has a particularly two-dimensional shape. AMF-LSDA+U calculations (with a Coulomb U of about 3 eV and exchange J of 0.6 eV) lead to a non-magnetic ground state for PuCoGa{sub 5}, in which the 5f states are shifted to a higher binding energy, in better agreement with photoemission data. The Fermi surface of PuCoGa{sub 5} computed with the AMF-LSDA+U approach is nonetheless rather two-dimensional and similar to the LSDA Fermi surface. The AMF-LSDA+U approach with a Coulomb U of {approx}3 eV would thus predict an electronic structure for PuCoGa{sub 5} in accord with several experimental data.

Polyurethane/Polylactide-Blend Films Doped with Zinc Ions for the Growth and Expansion of Human Olfactory Ensheathing Cells (OECs and Adipose-Derived Mesenchymal Stromal Stem Cells (ASCs for Regenerative Medicine Applications

Directory of Open Access Journals (Sweden)

Krzysztof Marycz

2016-04-01

Full Text Available Polymeric biomaterials based on polyurethane and polylactide blends are promising candidates for regenerative medicine applications as biocompatible, bioresorbable carriers. In current research we showed that 80/20 polyurethane/polylactide blends (PU/PLDL with confirmed biological properties in vitro may be further improved by the addition of ZnO nanoparticles for the delivery of bioactive zinc oxide for cells. The PU/PLDL blends were doped with different concentrations of ZnO (0.001%, 0.01%, 0.05% and undertaken for in vitro biological evaluation using human adipose stromal stem cells (ASCs and olfactory ensheathing cells (OECs. The addition of 0.001% of ZnO to the biomaterials positively influenced the morphology, proliferation, and phenotype of cells cultured on the scaffolds. Moreover, the analysis of oxidative stress markers revealed that 0.001% of ZnO added to the material decreased the stress level in both cell lines. In addition, the levels of neural-specific genes were upregulated in OECs when cultured on sample 0.001 ZnO, while the apoptosis-related genes were downregulated in OECs and ASCs in the same group. Therefore, we showed that PU/PLDL blends doped with 0.001% of ZnO exert beneficial influence on ASCs and OECs in vitro and they may be considered for future applications in the field of regenerative medicine.

Electrospun polyacrylonitrile/polyurethane composite nanofibrous separator with electrochemical performance for high power lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Zainab, Ghazala [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Wang, Xianfeng, E-mail: wxf@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China); Yu, Jianyong [Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China); Zhai, Yunyun; Ahmed Babar, Aijaz; Xiao, Ke [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Ding, Bin, E-mail: binding@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Key Laboratory of Textile Science & Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of High Performance Fibers & Products, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Nanofibers Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China)

2016-10-01

Lithium ion batteries (LIBs) for high performance require separators with auspicious reliability and safety. Keeping LIBs reliability and safety in view, microporous polyacrylonitrile (PAN)/polyurethane (PU) nonwoven composite separator have been developed by electrospinning technique. The physical, electrochemical and thermal properties of the PAN/PU separator were characterized. Improved ionic conductivity up to 2.07 S cm{sup −1}, high mechanical strength (10.38 MPa) and good anodic stability up to 5.10 V are key outcomes of resultant membranes. Additionally, high thermal stability displaying only 4% dimensional change after 0.5 h long exposure to 170 °C in an oven, which could be valuable addition towards the safety of LIBs. Comparing to commercialized polypropylene based separators, resulting membranes offered improved internal short-circuit protection function, offering better rate capability and enhanced capacity retention under same observation conditions. These fascinating characteristics endow these renewable composite nonwovens as promising separators for high power LIBs battery. - Highlights: • The PAN/PU based separators were prepared by multi-needle electrospinning technique. • The electrospun separators displays good mechanical properties and thermal stability. • These separators exhibit good wettability with liquid electrolyte, high ion conductivity and internal short-circuit protection. • Nanofibrous composite nonwoven possesses stable cyclic performance which give rise to acceptable battery performances.

Experience with Pu-recycle fuel for large light water reactors in the Federal Republic of Germany

International Nuclear Information System (INIS)

Stehle, H.; Spierling, H.; Eickelpasch, N.; Stoll, W.

1977-01-01

In general, design and operational performance of Pu-bearing recycle fuel are quite similar to those of Uranium fuel. Up to Nov. 1976 153 Pu-bearing fuel assemblies with altogether 8000 fuel rods, fabricated by ALKEM, have been or are in operation in German power reactors. Their performance is very satisfactory. In the Obrigheim and in the Gundremmingen plant up to 20% of the core are made up of Pu-fuel. In either case all-Pu fuel assemblies are used, graded in their Pu-content for compatibility with the surrounding U-fuel. The physics calculations are accomplished with basically the same methods as applied for U-fuel. Theoretical investigations and physics measurements have shown that differences in reactivity balance can be minimized by proper loading patterns. In additional experiments at elevated temperature (KRITZ) the neutron physics methods were verified in greater detail. The main feature of fabrication of mixed oxide pellets is mechanical blending of natural UO 2 - and PuO 2 -powder before pressing green pellets, and a rather high degree of mechanisation in all fabrication steps including sintering, wet grinding, and rod filling operations. The Zircaloy cladding know-how, welding techniques, final surface treatment etc. were all taken from the large experience of KWU in the LWR fuel area. Several fuel assemblies have been examined in the spent fuel pools and in hot cell laboratories after a maximum burn-up of 30 GWd/t. The examinations revealed no significant differences compared to U-fuel. Fission gas release is somewhat higher, attributed to the inhomogeneous fissioning on the microscopic scale in the mechanically mixed oxide. For the same reason the rate of densification is reduced. No Pu-redistribution has been observed. β-scans ( 140 La) and isotopic analyses confirmed the adequate accuracy of the calculation methods. In order to investigate the thermo-mechanical behaviour especially under power ramping conditions in greater depth mixed oxide test

Effect of water pressure on absorbency of hydroentangled greige cotton nonwoven fabrics

Science.gov (United States)

A studied has been conducted to determine the effect of water pressure in a commercial-grade Fleissner MiniJet hydroentanglement system on the absorbency of greige (non-bleached) cotton lint-based nonwoven fabric. The study has shown that a water pressure of 125 Bar or higher on only two high-pressu...

Liquid chromatographic studies on the behaviour of Pu(III), Pu(IV) and Pu(VI) on a RP stationary phase in presence of α-hydroxyisobutyric acid as a chelating agent

Energy Technology Data Exchange (ETDEWEB)

Jaison, P.G.; Kumar, Pranaw; Telmore, Vijay M. [Bhabha Atomic Research Centre, Mumbai (India). Fuel Chemistry Division

2017-06-01

Since plutonium possesses multiple oxidation states which can coexist in solution, a method for the identification of these oxidation states is important to understand its chemical processes. Liquid chromatographic studies were carried out to compare the chromatographic behaviour of different oxidation states of Pu in presence of the eluent, α-hydroxyisobutyric acid (HIBA). The three oxidation states of Pu viz. Pu(III), Pu(IV) and Pu(VI) were separated under optimised conditions. It was seen that the presence of the complexing agent influences the equilibrium of Pu(III)/(IV) as well as Pu(IV)/(VI) systems. Pu(III) to Pu(IV) conversion was found to be enhanced by high pH and concentration of HIBA whereas a relatively low pH and high concentration of HIBA promotes the conversion of Pu(VI) to Pu(IV).

Evaluation of nuclear data of 244Pu and 237Pu

International Nuclear Information System (INIS)

Nakagawa, Tsuneo; Konshin, V.A.

1995-10-01

The evaluation of nuclear data for 244 Pu and 237 Pu was made in the neutron energy region from 10 -5 eV to 20 MeV. For the both nuclides, the total, elastic and inelastic scattering, fission, capture, (n,2n) and (n,3n) reaction cross sections were evaluated on the basis of theoretical calculation. The resonance parameters were given for 244 Pu. The angular and energy distributions of secondary neutrons were also estimated for the both nuclides. The results were compiled in the ENDF-5 format and will be adopted in JENDL Actinoid File. (author)

Abaca/polyester nonwoven fabric functionalization for metal ion adsorbent synthesis via electron beam-induced emulsion grafting

International Nuclear Information System (INIS)

Madrid, Jordan F.; Ueki, Yuji; Seko, Noriaki

2013-01-01

A metal ion adsorbent was developed from a nonwoven fabric trunk material composed of both natural and synthetic polymers. A pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca/polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on absorbed dose, reaction time and monomer concentration were evaluated. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3 h reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 °C, a grafted APNWF with a Dg greater than 150% was obtained. The GMA-grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 °C to introduce amine functional groups. After a 3 h reaction with 50% EDA, an amine group density of 2.7 mmole/gram adsorbent was achieved based from elemental analysis. Batch adsorption experiments were performed using Cu 2+ and Ni 2+ ions in aqueous solutions with initial pH of 5 at 30 °C. Results show that the adsorption capacity of the grafted adsorbent for Cu 2+ is four times higher than Ni 2+ ions. - Highlights: • An amine type adsorbent from abaca/polyester nonwoven fabric was synthesized. • Pre-irradiation method was used in grafting glycidyl methacrylate on nonwoven fabric. • Radiation-induced grafting was performed with monomer in emulsion state. • The calculated adsorption capacity for Cu 2+ is four times higher than Ni 2+ ions. • Grafted adsorbent can remove Cu 2+ faster than a chemically similar commercial resin

Worldwide data on fluxes of 239,240Pu, 238Pu to the oceans

International Nuclear Information System (INIS)

Aarkrog, A.

1987-04-01

According to measurements (GEOSECS) the world's oceans contain approximately 16 PBq 239,240 Pu, of which one-fourth is in the Atlantic and three-fourths in the Pacific Ocean. The expected inventory (from nuclear weapons testing) in the world's oceans is 12 PBq 239,240 Pu including local fallout at the test sites. In the Irish Sea a local contamination of 0.3 PBq 239,240 Pu from the Sellafield reprocessing plant resides in the sediments. No other sources than fallout and reprocessing add significantly to the 239,240 Pu inventories in the oceans. The discrepancy between measurements and expectations are assumed to be due to an underestimate of the rainfall and dry fallout (seaspray) and thus of the Pu-deposition over the oceans, but may also to some degree be due to inadequate sampling

Reversed phase chromatographic behaviour of Pu (III), Pu (IV) and Pu (VI) in presence of α-hydroxyisobutyric acid

International Nuclear Information System (INIS)

Jaison, P.G.; Telmore, V.M.; Kumar, Pranaw

2016-01-01

Understanding the aqueous chemistry of plutonium is important in process conditions as well as in environmental conditions. Since plutonium possesses multiple oxidation states which can coexist in solution, a reliable method for the identification of these oxidation states is essential to understand its physical and chemical processes. The identification of plutonium oxidation states is conventionally determined through a series of liquid-liquid extraction procedures using selective extractants. Spectroscopic and laser based techniques also have been used for the identification of its oxidation state in solutions. Liquid chromatographic behavior of different oxidation states of Pu and other actinide ions is reported to correlate their retention behaviour with stability constants. Objective of the present work is to study the reversed phase chromatography behavior of the three oxidation states of plutonium viz. Pu(III), Pu(IV) and Pu(VI) in presence of á-hydroxyisobutyric acid (HIBA) as an eluent

Redox reactions of Pu(IV) and Pu(III) in the presence of acetohydroxamic acid in HNO(3) solutions.

Science.gov (United States)

Tkac, Peter; Precek, Martin; Paulenova, Alena

2009-12-21

The reduction of Pu(IV) in the presence of acetohydroxamic acid (HAHA) was monitored by vis-NIR spectroscopy. All experiments were performed under low HAHA/Pu(IV) ratios, where only the Pu(IV)-monoacetohydroxamate complex and Pu uncomplexed with HAHA were present in relevant concentrations. Time dependent concentrations of all absorbing species were resolved using molar extinction coefficients for Pu(IV), Pu(III), and the Pu(AHA)(3+) complex by deconvolution of spectra. From fitting of the experimental data by rate equations integrated by a numeric method three reactions were proposed to describe a mechanism responsible for the reduction and oxidation of plutonium in the presence of HAHA and HNO(3). Decomposition of Pu(AHA)(3+) follows a second order reaction mechanism with respect to its own concentration and leads to the formation of Pu(III). At low HAHA concentrations, a two-electron reduction of uncomplexed Pu(IV) with HAHA also occurs. Formed Pu(III) is unstable and slowly reoxidizes back to Pu(IV), which, at the point when all HAHA is decomposed, can be catalyzed by the presence of nitrous acid.

Determination of 238Pu, 239+240Pu, 241Pu and 241Am in radioactive waste from IPEN reactor

International Nuclear Information System (INIS)

Geraldo, Bianca; Taddei, Maria Helena T.; Cheberle, Sandra M.; Ferreira, Marcelo T.

2011-01-01

Ion exchange resin is a common type of radioactive waste arising from treatment of coolant water of the main circuit of research and nuclear power reactors. This waste contains high concentrations of fission and activation products. The management of this waste includes its characterization in order to determine and quantify specific radionuclides including those known as difficult-to-measure radionuclides (RDM). The analysis of RDMs generally involves expensive and time-consuming complex radiochemical analysis for purification and separation of the radionuclides. The objective of this work is to show an easy methodology for quantifying plutonium and americium isotopes in spent ion exchange resin, used for purification of the cooling water of the IEA-R1 reactor located at the Nuclear and Energy Research Institute, IPEN-CNEN/SP. The resins were destroyed by acid digestion, followed by purification and separation of the Pu and Am isotopes with anionic and chromatographic resins. 238 Pu, 239 + 24 '0Pu, and 24 '1Am isotopes were analyzed in an alpha spectrometer equipped with surface barrier detectors. 241 Pu isotope was analyzed by liquid scintillation counting. Chemical recovery yield ranged from 73 to 98% for Pu and 77 to 98% for Am, demonstrating that the methodology is suitable for identification and quantification of the isotopes studied in spent resins. (author)

Presence of plutonium isotopes, 239Pu and 240Pu, in soils from Chile

International Nuclear Information System (INIS)

Chamizo, E.; García-León, M.; Peruchena, J.I.; Cereceda, F.; Vidal, V.; Pinilla, E.; Miró, C.

2011-01-01

Plutonium is present in every environmental compartment, due to a variety of nuclear activities. The Southern Hemisphere has received about 20% of the global 239 Pu and 240 Pu environmental inventory, with an important contribution of the so-called tropospheric fallout from both the atmospheric nuclear tests performed in the French Polynesia and in Australia by France and United Kingdom, respectively. In this work we provide new data on the impact of these tests to South America through the study of 239 Pu and 240 Pu in soils from different areas of Northern, Central and Southern Chile. The obtained results point out to the presence of debris from the French tests in the 20–40° Southern latitude range, with 240 Pu/ 239 Pu atomic ratios quite heterogeneous and ranging from 0.02 to 0.23. They are significantly different from the expected one for the global fallout in the Southern Hemisphere for the 30–53°S latitude range (0.185 ± 0.047), but they follow the same trend as the reported values by the Department of Energy of United States for other points with similar latitudes. The 239+240 Pu activity inventories show as well a wider variability range in that latitude range, in agreement with the expected heterogeneity of the contamination.

Data Evaluation of Actinide Cross Sections: ²³⁸Pu, ²³⁷Pu, and ²³⁶Pu

Energy Technology Data Exchange (ETDEWEB)

Guaglioni, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jurgenson, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Descalle, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thompson, I. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ormand, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Escher, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Younes, W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mattoon, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Beck, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-10-04

This report documents the recent evaluation of the ²³⁶Pu, ²³⁷Pu, and ²³⁸Pu cross section sets. Nuclear data evaluation is the fundamental interface that takes measured nuclear cross section data and turns them into a continuous curve that 1) is consistent with other measurements and nuclear reaction theory/models, and 2) is required by down-stream users. All experiments that generate nuclear data need to include an evaluation step for their data to be broadly useful to the end users.

242Pu as tracer for simultaneous determination of 237Np and 239,240Pu in environmental samples

DEFF Research Database (Denmark)

Chen, Q.J.; Dahlgaard, H.; Nielsen, S.P.

2002-01-01

A procedure has been developed using Pu-242 as tracer for simultaneous determination of Np-237 and Pu-239,Pu-240 in environmental samples. The validity of the method has been demonstrated by ICPMS and alpha-spectroscopy for up to 10 gram soil and sediment, seawater up to 200 litres. The paper...... from Np and Pu) R-before/R-after = 1.004 +/- 3.3% (S.D n = 20) and 1 litre seawater R-before/R-after = 1.019+/-1.9% (S.D., n = 12). Results from the intercomparison samples LAEA-135, LAEA-381 and from environmental samples are presented....... describes a suitable chemical procedure for Np and Pu including a quantitative pre-concentration of neptunium and plutonium, preparation of Np4+ and Pu4+, NP(NO3)(6)(2-) and Pu(NO3)(6)(2-), The ratio of Np-237/Pu-242 (or Np-237/Pu-239) before and after the procedure has been determined using 10 g soil (free...

Determination of Pu in soil samples; Determinacion de Pu en muestras de suelo

Energy Technology Data Exchange (ETDEWEB)

Torres C, C. O.; Hernandez M, H.; Romero G, E. T. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Vega C, H. R., E-mail: carioli_32907@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

2016-10-15

The irreversible consequences of accidents occurring in nuclear plants and in nuclear fuel reprocessing sites are mainly the distribution of different radionuclides in different matrices such as the soil. The distribution in the superficial soil is related to the internal and external exposure to the radiation of the affected population. The internal contamination with radionuclides such as Pu is of great relevance to the nuclear forensic science, where is important to know the chemical and isotopic compositions of nuclear materials. The objective of this work is to optimize the radiochemical separation of plutonium (Pu) from soil samples and to determine their concentration. The soil samples were prepared using acid digestion assisted by microwave; purification of Pu was carried out with AG1X8 resin using ion exchange chromatography. Pu isotopes were measured using ICP-SFMS. In order to reduce the interference due to the presence of {sup 238}UH {sup +} in the samples, a solvent removal system (Apex) was used. In addition, the limit of detection and quantification of Pu was determined. It was found that the recovery efficiency of Pu in soil samples ranges from 70 to 93%. (Author)

Removal of Arsenic (V) from Aqueous Solutions Using Chitosan-Red Scoria and Chitosan-Pumice Blends.

Science.gov (United States)

Asere, Tsegaye Girma; Mincke, Stein; De Clercq, Jeriffa; Verbeken, Kim; Tessema, Dejene A; Fufa, Fekadu; Stevens, Christian V; Du Laing, Gijs

2017-08-09

In different regions across the globe, elevated arsenic contents in the groundwater constitute a major health problem. In this work, a biopolymer chitosan has been blended with volcanic rocks (red scoria and pumice) for arsenic (V) removal. The effect of three blending ratios of chitosan and volcanic rocks (1:2, 1:5 and 1:10) on arsenic removal has been studied. The optimal blending ratio was 1:5 (chitosan: volcanic rocks) with maximum adsorption capacity of 0.72 mg/g and 0.71 mg/g for chitosan: red scoria (Ch-Rs) and chitosan: pumice (Ch-Pu), respectively. The experimental adsorption data fitted well a Langmuir isotherm ( R ² > 0.99) and followed pseudo-second-order kinetics. The high stability of the materials and their high arsenic (V) removal efficiency (~93%) in a wide pH range (4 to 10) are useful for real field applications. Moreover, the blends could be regenerated using 0.05 M NaOH and used for several cycles without losing their original arsenic removal efficiency. The results of the study demonstrate that chitosan-volcanic rock blends should be further explored as a potential sustainable solution for removal of arsenic (V) from water.

Oxidation behaviour of plutonium rich (U, Pu)C and (U, Pu)O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Sali, S.K., E-mail: sksali@barc.gov.in [Fuel Chemistry Division (India); Kulkarni, N.K.; Phatak, Rohan [Fuel Chemistry Division (India); Agarwal, Renu [Product Development Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2016-10-15

Oxidation behaviour of (U{sub 0.3}Pu{sub 0.7})C{sub 1.06} was investigated in air by heating samples up to 1073 K and 1273 K. Thermogravimetry (TG) of the samples and X-ray powder diffraction (XRD) of the intermediate products were used to understand the phenomenon taking place during this process. Theoretical calculations were carried out to understand the multiple phase changes taking place during oxidation of carbide. Theoretical results were validated by XRD analysis of the products obtained at different stages of oxidation. The final oxidized products were found to be a single FCC phase with O/M = 2.15 (M = U + Pu). Oxidation kinetic studies of (U{sub 0.3}Pu{sub 0.7})O{sub 2} and (U{sub 0.47}Pu{sub 0.53})O{sub 2} were carried out in dry air, using thermogravimetry, under non-isothermal conditions. The activation energy of oxidation was found to be 49 and 70 kJ/mol, respectively. Lattice parameter dependence on Pu/M and O/M of plutonium rich mixed oxide (MOX) was established using combined results of XRD and TG analysis of (U{sub 0.3}Pu{sub 0.7})O{sub 2+x} and (U{sub 0.47}Pu{sub 0.53})O{sub 2+x}.

Localized 5f electrons in superconducting PuCoIn5: consequences for superconductivity in PuCoGa5

International Nuclear Information System (INIS)

Bauer, E D; Altarawneh, M M; Tobash, P H; Gofryk, K; Ayala-Valenzuela, O E; Mitchell, J N; McDonald, R D; Mielke, C H; Ronning, F; Scott, B L; Thompson, J D; Griveau, J-C; Colineau, E; Eloirdi, R; Caciuffo, R; Janka, O; Kauzlarich, S M

2012-01-01

The physical properties of the first In analog of the PuMGa 5 (M = Co, Rh) family of superconductors, PuCoIn 5 , are reported. With its unit cell volume being 28% larger than that of PuCoGa 5 , the characteristic spin-fluctuation energy scale of PuCoIn 5 is three to four times smaller than that of PuCoGa 5 , which suggests that the Pu 5f electrons are in a more localized state relative to PuCoGa 5 . This raises the possibility that the high superconducting transition temperature T c = 18.5 K of PuCoGa 5 stems from the proximity to a valence instability, while the superconductivity at T c = 2.5 K of PuCoIn 5 is mediated by antiferromagnetic spin fluctuations associated with a quantum critical point. (fast track communication)

Improved MOX fuel calculations using new Pu-239, Am-241 and Pu-240 evaluations

International Nuclear Information System (INIS)

Noguere, G.; Bouland, O.; Bernard, D.; Leconte, P.; Blaise, P.; Peneliau, Y.; Vidal, J.F.; Saint Jean, C. de; Leal, L.; Schilleebeeckx, P.; Kopecky, S.; Lampoudis, C.

2013-01-01

Several studies based on the JEFF-3.1.1 nuclear data library show a systematic over-estimation of the critical keff for core configurations of MOX fuel assemblies. The present work investigates possible improvements of the C/E results by using new evaluations for Am-241, Pu-239 and Pu-240. The work reported in this paper demonstrates the performances of the new Am-241 evaluation based on capture and transmission data measured at the IRMM. For Pu-239, the new evaluation, established in the frame of the WPEC/SG-34, is able to explain a systematic discrepancy observed between different EOLE experiments. The combination of the Am-241 and Pu-239 evaluations demonstrates the necessity to improve the radiation width of the first resonance of Pu-240

Determination of 240Pu/239Pu isotope ratios in Kara Sea and Novaya Zemlya sediments using accelerator mass spectrometry

International Nuclear Information System (INIS)

Oughton, D.H.; Skipperud, L.; Salbu, B.; Fifield, L.K.; Cresswell, R.C.; Day, J.P.

1999-01-01

Accelerator mass spectrometry (AMS) has been used to determine Pu activity concentrations and 240 Pu/ 239 Pu isotope ratios in sediments from the Kara Sea and radioactive waste dumping sites at Novaya Zemlya. Measured 239,240 Pu activities ranged from 0.06 - 9.8 Bq/kg dry weight, 240 Pu/ 239 Pu atom ratios ranged from 0.13 to 0.28, and 238 Pu/ 239,240 Pu activity ratios from 0.02 to 0.6. Perturbations from global fallout isotope ratios were evident at three sites: the Yenisey Estuary and Abrosimov Fjords where 240 Pu/ 239 Pu ratios were lower (0.13-0.14); and Stepovogo Fjord sediments where ratios were higher (up to 0.28) than fallout ratios. Based on procedural blanks, detection limits for AMS were below 1 fg Pu and the method showed good precision for isotope ratio measurements, minimal matrix, interference and memory effects. For high level samples, comparison between alpha spectrometry and AMS gave good agreement for measurement of 239,240 Pu activity concentrations. (author)

Influence of absorbed moisture on surface hydrophobization of ethanol pretreated and plasma treated ramie fibers

International Nuclear Information System (INIS)

Zhou Zhou; Wang Jilong; Huang Xiao; Zhang Liwen; Moyo, Senelisile; Sun Shiyuan; Qiu Yiping

2012-01-01

The existence of moisture in the substrate material may influence the effect of atmospheric pressure plasma treatment. Our previous study has found that the employment of ethanol pretreatment and plasma treatment can effectively induce hydrophobic surface modification of cellulose fiber to enhance the compatibility to polypropylene (PP) matrix, and this study aims to investigate the influence of fiber moisture regain on the treatment effect of this technique. Ramie fibers with three different moisture regains (MR) (2.5, 6.1 and 23.5%) are pretreated with ethanol followed by atmospheric pressure plasma treatment. Scanning electron microscope (SEM) shows that the 2.5% MR group has the most significant plasma etching effect. X-ray photoelectron spectroscopy (XPS) analysis indicates an increase of C-C and a decrease of C-O bond in the plasma treated groups, and the largest raise of C-C bond for the 2.5% MR group. The water contact angles of the 2.5 and 6.1% MR groups increase, whereas no significant change is showed in the 23.5% MR group. The interfacial shear strengths (IFSS) measured by microbond pull-out test are raised by 44 and 25% when moisture regains are 2.5 and 6.1%, while presented no apparent improvement at high moisture regain of 23.5%. Therefore, it can be concluded that moisture regain has negative influence on the surface hydrophobization of ramie fibers in the improvement of adhesion property to PP matrix.

Influence of absorbed moisture on surface hydrophobization of ethanol pretreated and plasma treated ramie fibers

Energy Technology Data Exchange (ETDEWEB)

Zhou Zhou; Wang Jilong; Huang Xiao; Zhang Liwen; Moyo, Senelisile; Sun Shiyuan [Key Laboratory of Textile Science and Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China); Qiu Yiping, E-mail: ypqiu@dhu.edu.cn [Key Laboratory of Textile Science and Technology, Ministry of Education, College of Textiles, Donghua University, Shanghai 201620 (China)

2012-03-01

The existence of moisture in the substrate material may influence the effect of atmospheric pressure plasma treatment. Our previous study has found that the employment of ethanol pretreatment and plasma treatment can effectively induce hydrophobic surface modification of cellulose fiber to enhance the compatibility to polypropylene (PP) matrix, and this study aims to investigate the influence of fiber moisture regain on the treatment effect of this technique. Ramie fibers with three different moisture regains (MR) (2.5, 6.1 and 23.5%) are pretreated with ethanol followed by atmospheric pressure plasma treatment. Scanning electron microscope (SEM) shows that the 2.5% MR group has the most significant plasma etching effect. X-ray photoelectron spectroscopy (XPS) analysis indicates an increase of C-C and a decrease of C-O bond in the plasma treated groups, and the largest raise of C-C bond for the 2.5% MR group. The water contact angles of the 2.5 and 6.1% MR groups increase, whereas no significant change is showed in the 23.5% MR group. The interfacial shear strengths (IFSS) measured by microbond pull-out test are raised by 44 and 25% when moisture regains are 2.5 and 6.1%, while presented no apparent improvement at high moisture regain of 23.5%. Therefore, it can be concluded that moisture regain has negative influence on the surface hydrophobization of ramie fibers in the improvement of adhesion property to PP matrix.

Ash Stabilization Campaign Blend Plan

International Nuclear Information System (INIS)

Winstead, M.L.

1995-01-01

This Stabilization Blend Plan documents the material to be processed and the processing order for the FY95 Ash Stabilization Campaign. The primary mission of this process is to reduce the inventory of unstable plutonium bearing ash. The source of the ash is from Rocky Flats and the 232-Z incinerator at the Plutonium Finishing Plant (PFP). The ash is currently being stored in Room 235B and Vault 174 in building 234-5Z. The sludge is to be thermally stabilized in a glovebox in room 230A of the 234-5Z building and material handling for the process will be done in room 230B of the same building. The campaign is scheduled for approximately 12--16 weeks. A total of roughly 4 kg of Pu will be processed

Physical and combustion properties of nonwoven fabrics produced from conventional and naturally colored cottons

Science.gov (United States)

A comparative study was conducted to identify the effects of processing parameters on physical and combustion properties of needlepunched (NP) and hydroentangled (H-E) nonwoven fabrics produced from fibers of a standard Mid-South white fiber cotton and a naturally colored brown fiber cotton. The fl...

Natural Pu-traces within the continental crust

International Nuclear Information System (INIS)

Ganz, M.; Barth, H.; Fuest, M.; Molzahn, D.; Brandt, R.

1991-01-01

Pu-traces are observed in the environmental all over the world, 'man made'-Pu as well as 'natural' Pu ( 239 Pu). 239 Pu occurs within a range of about 10 -12 g Pu/g sample in pitchblende. In the FRG, the deep-drilling project 'KTB, Kontinentales Tiefbohrprogramm', was started with the aim to obtain a very deep hole (14 km). We wanted to establish upper concentration limits for plutonium in samples from KTB. For a first investigation, we obtained a 400 g sample of granite from a pre-drill of KTB. Its Pu-concentration was ≤ (4.5 ± 2.5)x10 -16 g 239 Pu/g sample. To compare this result to the Pu-content in geological brines, we obtained a sample from a borehole at the Salton Sea Geothermal field (Southeastern California). In this sample we found an upper concentration limit of (2.1 ± 1.0)x10 -16 g 239 Pu/g sample. (orig.)

Nonwoven production from agricultural okra wastes and investigation of their thermal conductivities

Science.gov (United States)

Duman, M. N.; Kocak, E. D.; Merdan, N.; Mistik, I.

2017-10-01

Nowadays bio-based composite materials have been used in rising amounts and demanded widely in industrial uses, as they provide cost reduction and weight loss in the end use products. Agricultural cellulose based wastes can be a good alternative to synthetic fibers and can be used in natural fiber reinforced composite production, as there is a huge (more than 40 million tons) potential for natural cellulose production from agricultural wastes. Okra is one of the most grown vegetables around the world with stems left on the fields after harvest. When the similarity of mechanical properties of okra fibers with traditional bast fibers (flax, kenaf, hemp) are considered, from an economical and an environmental point of view this research emphasizes the potential of agricultural biomass for natural fiber production. In this study, okra stem wastes used for natural cellulosic fiber production and treated with 10% NaOH at 60°C for 10, 20, 30 and 40 minutes. By alkali treatment, decrease in fiber diameter and weight, and increase in tensile strength and elongation % have been observed. Nonwoven production has been done from both the fibers with and without surface treatments. Thermal conductivity properties of both nonwovens have been investigated.

Review of the thermodynamics of the U--C, Pu--C, and U--Pu--C systems

International Nuclear Information System (INIS)

Tetenbaum, M.; Sheth, A.; Olson, W.

1975-06-01

Thermodynamic properties such as enthalpy, heat capacity, entropy, heat and free energy of formation, and vaporization behavior are presented for the U--C, Pu--C, and U--Pu--C systems. These properties are of interest to scientists and engineers involved in the expanding field of advanced fuel LMFBR systems. The information on these systems has been derived largely from the discussions of the IAEA Panel on the assessment of thermodynamic properties of the U--C, Pu--C, and U--Pu--C systems. (U.S.)

Designing Pu600 for Authentication

International Nuclear Information System (INIS)

White, G.

2008-01-01

Many recent Non-proliferation and Arms Control software projects include an authentication component. Demonstrating assurance that software and hardware performs as expected without hidden 'back-doors' is crucial to a project's success. In this context, 'authentication' is defined as determining that the system performs only its intended purpose and performs that purpose correctly and reliably over many years. Pu600 is a mature software solution for determining the presence of Pu and the ratio of Pu240 to Pu239 by analyzing the gamma ray spectra in the 600 KeV region. The project's goals are to explore hardware and software technologies which can by applied to Pu600 which ease the authentication of a complete, end-to-end solution. We will discuss alternatives and give the current status of our work

Evaluation of fission cross sections and covariances for 233U, 235U, 238U, 239Pu, 240Pu, and 241Pu

International Nuclear Information System (INIS)

Kawano, Toshihiko; Matsunobu, Hiroyuki; Murata, Toru

2000-02-01

A simultaneous evaluation code SOK (Simultaneous evaluation on KALMAN) has been developed, which is a least-squares fitting program to absolute and relative measurements. The SOK code was employed to evaluate the fission cross sections of 233 U, 235 U, 238 U, 239 Pu, 240 Pu, and 241 Pu for the evaluated nuclear data library JENDL-3.3. Procedures of the simultaneous evaluation and the experimental database of the fission cross sections are described. The fission cross sections obtained were compared with evaluated values given in JENDL-3.2 and ENDF/B-VI. (author)

Evaluation of nuclear data of {sup 244}Pu and {sup 237}Pu

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Tsuneo; Konshin, V.A. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1995-10-01

The evaluation of nuclear data for {sup 244}Pu and {sup 237}Pu was made in the neutron energy region from 10{sup -5} eV to 20 MeV. For the both nuclides, the total, elastic and inelastic scattering, fission, capture, (n,2n) and (n,3n) reaction cross sections were evaluated on the basis of theoretical calculation. The resonance parameters were given for {sup 244}Pu. The angular and energy distributions of secondary neutrons were also estimated for the both nuclides. The results were compiled in the ENDF-5 format and will be adopted in JENDL Actinoid File. (author).

Influence of Low-Temperature Plasma Treatment on The Liquid Filtration Efficiency of Melt-Blown PP Nonwovens in The Conditions of Simulated Use of Respiratory Protective Equipment

Directory of Open Access Journals (Sweden)

Majchrzycka Katarzyna

2017-06-01

Full Text Available Filtering nonwovens produced with melt-blown technology are one of the most basic materials used in the construction of respiratory protective equipment (RPE against harmful aerosols, including bio- and nanoaerosols. The improvement of their filtering properties can be achieved by the development of quasi-permanent electric charge on the fibres. Usually corona discharge method is utilized for this purpose. In the presented study, it was assumed that the low-temperature plasma treatment could be applied as an alternative method for the manufacturing of conventional electret nonwovens for the RPE construction. Low temperature plasma treatment of polypropylene nonwovens was carried out with various process gases (argon, nitrogen, oxygen or air in a wide range of process parameters (gas flow velocity, time of treatment and power supplied to the reactor electrodes. After the modification, nonwovens were evaluated in terms of filtration efficiency of paraffin oil mist. The stability of the modification results was tested after 12 months of storage and after conditioning at elevated temperature and relative humidity conditions. Moreover, scanning electron microscopy and ATR-IR spectroscopy were used to assess changes in surface topography and chemical composition of the fibres. The modification of melt-blown nonwovens with nitrogen, oxygen and air plasma did not result in a satisfactory improvement of the filtration efficiency. In case of argon plasma treatment, up to 82% increase of filtration efficiency of paraffin oil mist was observed in relation to untreated samples. This effect was stable after 12 months of storage in normal conditions and after thermal conditioning in (70 ± 3°C for 24 h. The use of low-temperature plasma treatment was proven to be a promising improvement direction of filtering properties of nonwovens used for the protection of respiratory tract against harmful aerosols.

Studies of U-Pu-C-Ti compounds

International Nuclear Information System (INIS)

Milet, C.

1967-01-01

The U-Pu-C-Ti compounds (5 to 20 atoms per cent Ti) have been studied in order to improve some properties of U-Pu-C carbides and to extend the existence field of the (U, Pu) C phase. The Pu/(U+Pu) ratio has been fixed to 15 per cent. All the alloys were elaborated and cast in an arc furnace. A two-phases field (U, Pu) C + Ti C exists which permits to avoid di- and sesqui-carbides and the (U, Pu) phase. An eutectic between (U, Pu) C and Ti C was found around 15 atoms per cent Ti. Practically the whole of the titanium is in Ti C form, titanium solubility in (U, Pu) C being inferior to 1 atom per cent. The most promising alloy are those containing two phases: (U, Pu) C+ Ti C. In comparison with the (U, Pu) C phase, titanium addition does not change very much the thermal expansion coefficients nor the thermal cycling behaviour between 160 and 1000 Celsius degrees which is excellent. On the other hand atmospheric corrosion behaviour is improved; compatibility with stainless steel is better; thermal conductivity, calculated from electrical resistivity K is enhanced: for U(0.85)-Pu(0.15)-C alloy we have K 0.179 W/cm.C at 1000 C and K = 0.187 W/cm.C at 1500 C, for U-Pu-C-Ti (10 atoms % Ti) alloy we have K = 0.193 W/cm.C at 1000 C and K = 0.205 W/cm.C at 1500 C. (author) [fr

Local atomic structure of α-Pu

International Nuclear Information System (INIS)

Espinosa, F. J.; Villella, P.; Lashley, J. C.; Conradson, S. D.; Cox, L. E.; Martinez, R.; Martinez, B.; Morales, L.; Terry, J.; Pereyra, R. A.

2001-01-01

The local atomic structure of α-Pu was investigated using x-ray absorption fine structure (XAFS) spectroscopy. XAFS spectra were obtained for a zone-refined α-Pu and the results were compared to 32-year-old and Ce-doped (0.34 at.%) samples. X-ray diffraction (XRD) patterns were also measured for the zone-refined and 32-year-old materials. The extent of the Bragg peaks showed that amorphization of the 32-year-old sample had not occurred despite the prolonged exposure to self-radiation. Analogous to metastable δ-Pu alloys, the local atomic structure around Pu for the zone-refined material shows the possible presence of noncrystallographic Pu-Pu distances. Conversely, the Ce and the 32-year-old sample show no evidence for such noncrystallographic distances. Disorder in the Pu local environment was found to be impurity dependent. The Ce-doped sample presented a larger Pu-Pu nearest neighbor disorder than the aged sample, although the total amount of Am, U, and He impurities was actually higher in the aged sample. The local environment around U and Ce impurities is consistent with these elements being in substitutional lattice sites. In addition, U and Ce do not introduce significant lattice distortion to their nearest neighbors. This is consistent with disorder being more related to the perturbation of the coupling between the electronic and crystal structure, or the Peierls--Jahn-Teller distortion that generates the monoclinic α-Pu structure, and less to strain fields produced in the vicinity of the impurities

Designing Pu600 for Authentication

Energy Technology Data Exchange (ETDEWEB)

White, G

2008-07-10

Many recent Non-proliferation and Arms Control software projects include an authentication component. Demonstrating assurance that software and hardware performs as expected without hidden 'back-doors' is crucial to a project's success. In this context, 'authentication' is defined as determining that the system performs only its intended purpose and performs that purpose correctly and reliably over many years. Pu600 is a mature software solution for determining the presence of Pu and the ratio of Pu240 to Pu239 by analyzing the gamma ray spectra in the 600 KeV region. The project's goals are to explore hardware and software technologies which can by applied to Pu600 which ease the authentication of a complete, end-to-end solution. We will discuss alternatives and give the current status of our work.

Early retention of 237Pu + 239Pu in mature beagles

International Nuclear Information System (INIS)

Lloyd, R.D.; McFarland, S.S.; Atherton, D.R.; Bruenger, F.W.; Taylor, G.N.; Mays, C.W.

1978-01-01

Five mature beagles, ranging in age from 57 to 84 months, were injected intravenously with about 0.05-0.1 μCi/kg of 239 Pu(IV) citrate to which tracer amounts of the photon-emitter 237 Pu had been added. Plutonium retention in liver and in non-liver tissue (mainly skeleton) was measured periodically in the living dogs for nearly 4 months after injection by a combination of total-body and partial-body counting. All excreta were collected during the first 21 days and analysed for their Pu content. One dog was sacrificed at 14 days and another at 118 days for distribution studies. About 17% (14-20%) of the injected Pu was excreted in the urine and feces in the first 3 weeks, about the same as that excreted in a corresponding time by beagles injected as young adults (14%), but substantially more than beagles injected as juveniles (11%). In contrasts to juvenile beagles injected at 3 months of age, in which early retention was about 12% in liver and 68% in the skeleton, mature beagles retained about 30% in liver and 50% in the skeleton. Retention in young adult beagles injected at 17 months of age was similar to that of mature dogs. Relative distribution of skeletal plutonium among various bones was similar in the mature animals to that seen previously in young adults, but quite different from that of juveniles. A notable exception was the humerus for which there was no significant difference (P>0.2) in the % of retained skeletal Pu represented by the humerus among the juvenile, young adult and mature dogs. (author)

Two 238Pu inhalation incidents

International Nuclear Information System (INIS)

Fleming, R.R.; Hall, R.M.

1978-06-01

Two employees inhaled significant amounts of 238 Pu in separate unrelated contamination incidents in 1977. Both acute exposure incidents are described and the urine, feces, and in-vivo chest count data for each employee. Case B ( 238 PuNO 3 ) received 24 DTPA treatments beginning the day of the incident while, for medical reasons, Case A ( 238 PuO 2 ) received no therapy

239Pu(n, 2n) and 241Pu(n, 2n) surrogate cross section measurements using NeutronSTARS

Energy Technology Data Exchange (ETDEWEB)

Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alan, B. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Akindele, O. A. [Univ. of California, Berkeley, CA (United States); Casperson, R. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hughes, R. O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Koglin, J. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Tamashiro, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Oregon State Univ., Corvallis, OR (United States); Kolos, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Norman, E. B. [Univ. of California, Berkeley, CA (United States); Saastamoinen, A. [Univ. of California, Los Angeles, CA (United States); Padilla, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Univ. of California, Los Angeles, CA (United States); Fisher, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-12-08

The goal of this project was to develop a new approach to measuring (n,2n) reactions for isotopes of interest. We set out to measure the ²³⁹Pu(n,2n) and ²⁴¹Pu(n,2n) cross sections by directly detecting the 2n neutrons that are emitted. With the goal of improving the ²³⁹Pu(n,2n) cross section and to measure the ²⁴¹Pu(n,2n) cross section for the first time. To that end, we have constructed a new neutron-charged-particle detector array called NeutronSTARS. It has been described extensively in Casperson et al. [1] and in Akindele et al. [2]. We have used this new neutron-charged-particle array to measure the ²⁴¹Pu and ²³⁹Pu fission neutron multiplicity as a function of equivalent incident-neutron energy from 100 keV to 20 MeV. We have made a preliminary determination of the ²³⁹Pu(n,2n) and ²⁴¹Pu(n,2n) cross sections from the surrogate ²⁴⁰Pu(α,α’2n) and ²⁴²Pu(α,α’2n) reactions respectively. The experimental approach, detector array, data analysis, and results to date are summarized in the following sections.

Presence of plutonium isotopes, {sup 239}Pu and {sup 240}Pu, in soils from Chile

Energy Technology Data Exchange (ETDEWEB)

Chamizo, E., E-mail: echamizo@us.es [Centro Nacional de Aceleradores, Avda. Thomas Alba Edison, 7, 41092 Sevilla (Spain); Garcia-Leon, M., E-mail: manugar@us.es [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad de Sevilla, Avda. Reina Mercedes sn, 41012 Seville (Spain); Peruchena, J.I., E-mail: jiperuchena@gmail.com [Centro Nacional de Aceleradores, Avda. Thomas Alba Edison, 7, 41092 Sevilla (Spain); Cereceda, F., E-mail: francisco.cereceda@usm.cl [Laboratorio de Quimica Ambiental, Centro de Tecnologias Ambientales (CETAM), Universidad Tecnica Federico Santa Maria, Casilla 110-V, Valparaiso (Chile); Vidal, V., E-mail: victor.vidal@usm.cl [Laboratorio de Quimica Ambiental, Centro de Tecnologias Ambientales (CETAM), Universidad Tecnica Federico Santa Maria, Casilla 110-V, Valparaiso (Chile); Pinilla, E., E-mail: epinilla@unex.es [Departamento de Quimica Analitica, Facultad de Ciencias, Universidad de Extremadura, Avda. de Elvas sn, 06071 Badajoz (Spain); Miro, C., E-mail: cmiro@unex.es [Departamento de Fisica Aplicada, Universidad de Extremadura, Avda. de la Universidad sn, 10071 Caceres (Spain)

2011-12-15

Plutonium is present in every environmental compartment, due to a variety of nuclear activities. The Southern Hemisphere has received about 20% of the global {sup 239}Pu and {sup 240}Pu environmental inventory, with an important contribution of the so-called tropospheric fallout from both the atmospheric nuclear tests performed in the French Polynesia and in Australia by France and United Kingdom, respectively. In this work we provide new data on the impact of these tests to South America through the study of {sup 239}Pu and {sup 240}Pu in soils from different areas of Northern, Central and Southern Chile. The obtained results point out to the presence of debris from the French tests in the 20-40 Degree-Sign Southern latitude range, with {sup 240}Pu/{sup 239}Pu atomic ratios quite heterogeneous and ranging from 0.02 to 0.23. They are significantly different from the expected one for the global fallout in the Southern Hemisphere for the 30-53 Degree-Sign S latitude range (0.185 {+-} 0.047), but they follow the same trend as the reported values by the Department of Energy of United States for other points with similar latitudes. The {sup 239+240}Pu activity inventories show as well a wider variability range in that latitude range, in agreement with the expected heterogeneity of the contamination.

ANALISIS SIFAT TARIK DAN IMPAK KOMPOSIT SERAT RAMI DENGAN PERLAKUAN ALKALI DALAM WAKTU 2,4,6 DAN 8 JAM BERMATRIK POLIESTER

Directory of Open Access Journals (Sweden)

Pramuko Ilmu Purboputro

2017-10-01

Full Text Available Ikatan interfacal bonding pada komposit serat alam sangat tergantung dari kekasaran permukaan serat. Permukaan serat dapat ditingkatkan daya ikatan permukaannya dengan cara mencelupkan pada larutan alkali. Pencelupan ini akan mengurangi lapisan lignin yang mengurangi kekuatan ikat pada permukaan serat. Pada penelitian ini proses yang digunakan adalah perlakuan alkali terhadap permukaan serat dengan  cara merendam serat rami selama 2,4,6, dan 8 jam. Larutah alkali yang digunakan adalah larutan NaOH dengan konsentrasi 10% pada pelarut air. Serat rami   Boehmeria nivea (L Goud direndam pada larutan NaOH selama 2,4,6, dan 8 jam perendaman, untuk menghilangkan zat ligninnya agar kekuatan ikatan permukaan bisa diperbaiki.  Pengujian yang dilakukan adalah pengujian tarik dan pengujian impak. Hasil yang didapat adalah kekuatan tarik terbesar didapat pada perendaman 8 jam yaitu sebesar 41,9 MPa. Modulus young terbesar didapat pada perendaman 2 jam, yaitu 2743,15 Mpa, dan kekuatan impak terbesar adalah 0,0725 Joule/mm2 terjadi pada perendaman 4 jam   Kata kunci : komposit serat, kekuatan tarik, kekuatan impak, perendaman alkali

Anthropogenic Pu distribution in Tropical East Pacific

International Nuclear Information System (INIS)

Kinoshita, Norikazu; Sumi, Takahiro; Takimoto, Kiyotaka; Nagaoka, Mika; Yokoyama, Akihiko; Nakanishi, Takashi

2011-01-01

The geographical distribution of the anthropogenic radionuclides 238 Pu and 239+240 Pu in the Tropical East Pacific in 2003 was studied from the viewpoint of material migration. We measured the contents of Pu isotopes in seawater and in sediment from the sea bottom. The distributions of Pu isotopes, together with those of coexisting nitrate and phosphate species and dissolved oxygen, are discussed in relation to the potential temperature and potential density (sigma-θ). The Pu contents in sediment samples were compared with those in the seawater. Horizontal migration across the Equator from north to south was investigated at depths down to ∼ 800 m in the eastern Pacific. The Pu distribution at 0-400 m correlated well with the distribution of potential temperature. Maximum Pu levels were observed in the subsurface layer at 600-800 m, corresponding to the depth where sigma-θ ∼ 27.0. It is suggested that the Pu distribution depends on the structure of the water mass and the particular temperature and salinity. The water column/sediment column inventory ratio and the vertical distribution of Pu may reflect the efficiency of scavenging in the relevant water areas. Research Highlights: → Geographical distributions of Pu isotopes were investigated from viewpoint of material migration. → Horizontal migration from north to south was found at depths down to ∼800 m in the eastern Pacific. → Pu distribution at 0-400 m was correlated with water temperature. → The distribution at 600-800 m correlated with water mass structure. → Pu in seawater and sediment gave information about efficiency of scavenging.

{sup 137}Cs, {sup 239+240}Pu concentrations and the {sup 240}Pu/{sup 239}Pu atom ratio in a sediment core from the sub-aqueous delta of Yangtze River estuary

Energy Technology Data Exchange (ETDEWEB)

Pan, S.M., E-mail: span@nju.edu.cn [Key Lab of Ministry of Education of Coast and Island Development, Nanjing University, Nanjing 210093 (China); Tims, S.G. [Department of Nuclear Physics, Research School of Physics and Engineering, Australian National University, Canberra, ACT 0200 (Australia); Liu, X.Y. [Key Lab of Ministry of Education of Coast and Island Development, Nanjing University, Nanjing 210093 (China); Fifield, L.K. [Department of Nuclear Physics, Research School of Physics and Engineering, Australian National University, Canberra, ACT 0200 (Australia)

2011-10-15

A sediment core collected from the sub-aqueous delta of the Yangtze River estuary was subjected to analyses of {sup 137}Cs and plutonium (Pu) isotopes. The {sup 137}Cs was measured using {gamma}-spectrometry at the laboratories at the Nanjing University and Pu isotopes were determined with Accelerator Mass Spectrometry (AMS), measurements made at the Australian National University. The results show considerable structure in the depth concentration profiles of the {sup 137}Cs and {sup 239+240}Pu. The shape of the vertical {sup 137}Cs distribution in the sediment core was similar to that of the Pu. The maximum {sup 137}Cs and {sup 239+240}Pu concentrations were 16.21 {+-} 0.95 mBq/g and 0.716 {+-} 0.030 mBq/g, respectively, and appear at same depth. The average {sup 240}Pu/{sup 239}Pu atom ratio was 0.238 {+-} 0.007 in the sediment core, slightly higher than the average global fallout value. The changes in the {sup 240}Pu/{sup 239}Pu atom ratios in the sediment core indicate the presence of at least two different Pu sources, i.e., global fallout and another source, most likely close-in fallout from the Pacific Proving Grounds (PPG) in the Marshall Islands, and suggest the possibility that Pu isotopes are useful as a geochronological tool for coastal sediment studies. The {sup 137}Cs and {sup 239+240}Pu inventories were estimated to be 7100 {+-} 1200 Bq/m{sup 2} and 407 {+-} 27 Bq/m{sup 2}, respectively. Approximately 40% of the {sup 239+240}Pu inventory originated from the PPG close-in fallout and about 50% has derived from land-origin global fallout transported to the estuary by the river. This study confirms that AMS is a useful tool to measure {sup 240}Pu/{sup 239}Pu atom ratio and can provide valuable information on sedimentary processes in the coastal environment.

Comparison of the ENDF/B-V and SOKRATOR evaluations of 235U, 239Pu, 240Pu and 241Pu at low neutron energies

International Nuclear Information System (INIS)

de Saussure, G.; Wright, R.Q.

1981-01-01

The US and USSR's most recent evaluationsof 235 U, 239 Pu, 240 Pu and 241 Pu are compared over the thermal region and over the first few resonances. The two evaluations rest on essentially the same experimental data base and the differences reflect different approaches to the representation of the cross sections or different weightings of the experimental results. It is found that over the thermal and resolved ranges the two evaluations are very similar. Some differences in approaches are briefly discussed

Effect of storage conditions on graft of polypropylene non-woven fabric induced by electron beam

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin Young; Jeun, Joon Pyo; Kang, Phil Hyun [Radiation Research Dvision for Industry and Environment, Korea Atomic Energy Research Institute, Jeongeup(Korea, Republic of)

2015-05-15

In this study, we fabricated effect of storage conditions on graft of polypropylene (PP) non-woven fabric induced by electron beam. The electron beam irradiations on PP non-woven fabric were carried out over a range of irradiation doses from 25 to 100 kGy to make free radicals on fabric surface. The radical measurement was established by electron spin resonance (ESR) for confirming the changes of the alkyl radical and peroxy radical according to effect of storage time, storage temperature and atmosphere. It was observed that the free radicals were increased with irradiation dose and decreased with storage time due to the continuous oxidation. However, the radical extinction was significantly delayed due to reduced mobility of radicals at extremely low temperature. The degree of graft based on the analysis of ESR was investigated. The conditions of graft reaction were set at a temperature: 60 degrees Celcius, reaction time: 6 hours and styrene monomer concentration: 20 wt%.

The radiolysis of solutions containing Pu(6)

International Nuclear Information System (INIS)

Rance, P.J.W.; Zilberman, B.Y.

2000-01-01

The reduction of Pu(VI) in nitric acid solutions containing uranium and various fission product elements as a result of both its inherent alpha radiation and also external gamma irradiation at dose rates similar to those experienced by dissolved fuel solutions has been investigated. The presence of the additional metals has been shown to eliminate the induction periods required prior to the reduction of Pu(VI) in nitric acid. G values for the auto-radiolytic reduction of Pu(VI) have been found to be between 0.6 and 1.1 for 3 g/1 Pu solutions containing between 0.12 and 9.2 % 238 Pu (balance 239 Pu). Uranium and palladium have been found to accelerate the reduction of Pu(VI) during gamma irradiation at dose rates of between 0.41 and 1.64 kGy/hour. (authors)

The radiolysis of solutions containing Pu(6)

Energy Technology Data Exchange (ETDEWEB)

Rance, P.J.W. [BNFL British Nuclear Fuels, Sellafield, Seascale, Cumbria, Research and Technology (United Kingdom); Zilberman, B.Y. [V.G. Khlopin Radium Institute, St. Petersburg (Russian Federation)

2000-07-01

The reduction of Pu(VI) in nitric acid solutions containing uranium and various fission product elements as a result of both its inherent alpha radiation and also external gamma irradiation at dose rates similar to those experienced by dissolved fuel solutions has been investigated. The presence of the additional metals has been shown to eliminate the induction periods required prior to the reduction of Pu(VI) in nitric acid. G values for the auto-radiolytic reduction of Pu(VI) have been found to be between 0.6 and 1.1 for 3 g/1 Pu solutions containing between 0.12 and 9.2 % {sup 238}Pu (balance {sup 239}Pu). Uranium and palladium have been found to accelerate the reduction of Pu(VI) during gamma irradiation at dose rates of between 0.41 and 1.64 kGy/hour. (authors)

Pu speciation in actual and simulated aged wastes

Energy Technology Data Exchange (ETDEWEB)

Lezama-pacheco, Juan S [Los Alamos National Laboratory; Conradson, Steven D [Los Alamos National Laboratory

2008-01-01

X-ray Absorption Fine Structure Spectroscopy (XAFS) at the Pu L{sub II/III} edge was used to determine the speciation of this element in (1) Hanford Z-9 Pu crib samples, (2) deteriorated waste resins from a chloride process ion-exchange purification line, and (3) the sediments from two Waste Isolation Pilot Plant Liter Scale simulant brine systems. The Pu speciation in all of these samples except one is within the range previously displayed by PuO{sub 2+x-2y}(OH){sub y}{center_dot}zH{sub 2}O compounds, which is expected based on the putative thermodynamic stability of this system for Pu equilibrated with excess H{sub 2}O and O{sub 2} under environmental conditions. The primary exception was a near neutral brine experiment that displayed evidence for partial substitution of the normal O-based ligands with Cl{sup -} and a concomitant expansion of the Pu-Pu distance relative to the much more highly ordered Pu near neighbor shell in PuO{sub 2}. However, although the Pu speciation was not necessarily unusual, the Pu chemistry identified via the history of these samples did exhibit unexpected patterns, the most significant of which may be that the presence of the Pu(V)-oxo species may decrease rather than increase the overall solubility of these compounds. Several additional aspects of the Pu speciation have also not been previously observed in laboratory-based samples. The molecular environmental chemistry of Pu is therefore likely to be more complicated than would be predicted based solely on the behavior of PuO{sub 2} under laboratory conditions.

Computing and physical methods to calculate Pu

International Nuclear Information System (INIS)

Mohamed, Ashraf Elsayed Mohamed

2013-01-01

Main limitations due to the enhancement of the plutonium content are related to the coolant void effect as the spectrum becomes faster, the neutron flux in the thermal region tends towards zero and is concentrated in the region from 10 Ke to 1 MeV. Thus, all captures by 240 Pu and 242 Pu in the thermal and epithermal resonance disappear and the 240 Pu and 242 Pu contributions to the void effect became positive. The higher the Pu content and the poorer the Pu quality, the larger the void effect. The core control in nominal or transient conditions Pu enrichment leads to a decrease in (B eff.), the efficiency of soluble boron and control rods. Also, the Doppler effect tends to decrease when Pu replaces U, so, that in case of transients the core could diverge again if the control is not effective enough. As for the voiding effect, the plutonium degradation and the 240 Pu and 242 Pu accumulation after multiple recycling lead to spectrum hardening and to a decrease in control. One solution would be to use enriched boron in soluble boron and shutdown rods. In this paper, I discuss and show the advanced computing and physical methods to calculate Pu inside the nuclear reactors and glovebox and the different solutions to be used to overcome the difficulties that effect, on safety parameters and on reactor performance, and analysis the consequences of plutonium management on the whole fuel cycle like Raw materials savings, fraction of nuclear electric power involved in the Pu management. All through two types of scenario, one involving a low fraction of the nuclear park dedicated to plutonium management, the other involving a dilution of the plutonium in all the nuclear park. (author)

Metal-carbide multilayers for molten Pu containment

International Nuclear Information System (INIS)

Summers, T.S.E.; Curtis, P.G.; Juntz, R.S.; Krueger, R.L.

1991-12-01

Multilayers composed of nine or ten alternating layers of Ta or W and TaC were studied for the feasibility of their use in containing molten plutonium (Pu) at 1200 degrees C. Single layers of W and TaC were also investigated. A two-source electron beam evaporation process was developed to deposit these coatings onto the inside surface of hemispherical Ta cups about 38 mm in diameter. Pu testing was done by melting Pu in the coated hemispherical cups and holding them under vacuum at 1200 degrees C for two hours. Metallographic examination and microprobe analysis of cross sections showed that Pu had penetrated to the Ta substrate in all cases to some extent. Full penetration to the outer surface of the Ta substrate, however, occurred in only a few of the samples. The fact that full penetration occurred in any of the samples suggests that it would have occurred in uncoated Ta under these testing conditions which in turn suggests that the multilayer coatings do afford some protection against Pu attack. The TaC used for these specimens was wet by Pu under these testing conditions, and following testing, Pu was found uniformly distributed throughout the carbide layers which appeared to be rather porous. Pu was seen in the W and Ta layers only when exposed directly to molten Pu during testing or near defects suggesting that Pu penetrated the multilayers at defects in the coating and traveled parallel to the layers along the carbide layers. These results indicate that the use of alternating metal and ceramic layers for Pu containment should be possible through the use of nonporous ceramic that is not wet by molten Pu and defect-free films

Rapid monitoring particulate radiocesium with nonwoven fabric cartridge filter and application to field monitoring

International Nuclear Information System (INIS)

Tsuji, Hideki; Yasutaka, Tetsuo; Kondo, Yoshihiko; Kawashima, Shoji

2013-01-01

A method for rapid monitoring particulate radiocesium using a nonwoven fabric cartridge filter was developed, which needs no further preprocessing before served to a detector. By a performance test, more than 98% of suspended solid (SS) was collected. This method showed the same radioactivity measurement accuracy as filtration by membrane filter and more rapid extraction capability of SS. (author)

Functionalisation of polypropylene non-woven fabrics (NWFs): Functionalisation by oxyfluorination as a first step for graft polymerisation

CSIR Research Space (South Africa)

Vargha, V

2011-10-01

Full Text Available Surface oxyfluorination had been carried out on polypropylene non-woven fabric (PP NWF) samples of different morphologies and pore sizes. The modified surfaces were characterised by Attenuated Total Reflectance Fourier Transform InfraRed (ATR...

Influence of Immersion Conditions on The Tensile Strength of Recycled Kevlar®/Polyester/Low-Melting-Point Polyester Nonwoven Geotextiles through Applying Statistical Analyses

Directory of Open Access Journals (Sweden)

Jing-Chzi Hsieh

2016-05-01

Full Text Available The recycled Kevlar®/polyester/low-melting-point polyester (recycled Kevlar®/PET/LPET nonwoven geotextiles are immersed in neutral, strong acid, and strong alkali solutions, respectively, at different temperatures for four months. Their tensile strength is then tested according to various immersion periods at various temperatures, in order to determine their durability to chemicals. For the purpose of analyzing the possible factors that influence mechanical properties of geotextiles under diverse environmental conditions, the experimental results and statistical analyses are incorporated in this study. Therefore, influences of the content of recycled Kevlar® fibers, implementation of thermal treatment, and immersion periods on the tensile strength of recycled Kevlar®/PET/LPET nonwoven geotextiles are examined, after which their influential levels are statistically determined by performing multiple regression analyses. According to the results, the tensile strength of nonwoven geotextiles can be enhanced by adding recycled Kevlar® fibers and thermal treatment.

Modification of analytical method for measurement of 239Pu, 240Pu and 241Am in sediment and sea water

International Nuclear Information System (INIS)

Syarbaini; Tarigan, C.; Rustam, M.F.

1997-01-01

Modification of analytical method for measurement of 239 Pu, 240 Pu and 241 Am in sediment and sea water have been conducted. This study is to develop a method for separation of 239 Pu, 240 Pu and 241 Am from 100-300 g of sediment and 100-200 l of sea water samples. Most of the methods described in the literature are to separation of '2 39 Pu, '2 40 Pu and 241 Am from 20-50 g of sediment and 30-100 l of sea water samples. By this method, 239,240 Pu and 241 Am were concentrated using the coprecipitation of CaC 2 O 4 and Fe (OH) 3 . Plutonium-242 and Curium-244 were used as tracer to determine chemical recovery. The result of analysis of some sediment samples showed that the chemical recoveries were respectively obtained in the range of 59.7 to 72.6% with average of 66.2 % for 242 Pu and 72.0 % to 85.5 % with average 78.8 % for 244 Cm. Analysis of some sea water samples were obtained in the range of 67 % to 78 % with average 73.9 % for 242 Pu and 74.0 % to 90.0 % with average 84.2 % for '2 42 Cm. This method was tested by the IAEA marine sediment, the result was excellent agreement with the IAEA certified sediment. It could be suggested that the developed analytical method is suitable to analyze the low level 239 Pu, 240 Pu and 241 Am in sediment and sea water samples (author)

Radiation induced emulsion graft polymerization of 4-vinylpyridine onto PE/PP nonwoven fabric for As(V) adsorption

International Nuclear Information System (INIS)

Akkaş Kavaklı, Pınar; Kavaklı, Cengiz; Seko, Noriaki; Tamada, Masao; Güven, Olgun

2016-01-01

A novel nonwoven fabric adsorbent having 4-vinylpyridine functional groups was prepared by using radiation-induced emulsion graft polymerization method and grafting 4-vinylpyridine monomer onto a polyethylene-coated polypropylene nonwoven fabric (NWF) in aqueous emulsion solution. The grafting conditions of the 4-vinylpyridine monomer onto the NWF were optimised and 150% D g VP-g-NWF was prepared using 30 kGy pre-irradiation dose, 5% VP monomer concentration and 0.5% (w/w) Tween 20 in aqueous emulsion. Grafted 4-vinylpyridine chains on the NWF were then quaternized for the preparation of QVP-g-NWF adsorbent. All fabric structures were characterized by using Fourier-transform infrared spectrometer, x-ray photoelectron spectrometer and scanning electron microscope. QVP-g-NWF adsorbent was used in batch adsorption experiments for As(V) ions by studying the pH, contact time, and initial As(V) ion concentration parameters. Results showed that QVP-g-NWF adsorbent has significant As(V) adsorption and experimental As(V) adsorption capacity was 98.04 mg As(V)/g polymer from 500 mg/L initial As(V) concentration at pH 7.00. - Highlights: • Radiation induced grafting of 4-vinylpyridine onto PE/PP nonwoven fabric in emulsion. • 4-vinylpyridine grafting was characterized by FTIR, SEM and XPS. • As(V) adsorption was studied by QVP-g- NWF. • As(V) adsorption capacity was found to be 98.04 mg As(V)/g polymer.

Solution species of 239Pu [V] in the environment

International Nuclear Information System (INIS)

Rai, D.; Serne, R.J.; Swanson, J.L.

1978-01-01

Information regarding the oxidation states of Pu in environmental samples is needed for estimating its migration through the geologic media. Thermodynamic data were used to develop stability fields for different Pu species. The data indicate that in the Eh-pH range of natural aqueous environments, the dominant species of Pu is likely to be Pu[V] in relatively oxidizing environments and Pu[III] in reducing environments. Because of the lack of methods of determining Pu[V] in environmental samples containing trace concentrations of Pu, Pu[V] has not been previously identified in these samples. Plutonium [VI] is generally assumed to be the dominant species in relatively oxidizing environments. However, a combination of solvent extraction and spectrophotometric techniques used in this study show that solutions (> 10 -5 4 M Pu) in equilibrium with 239 Pu[IV] hydroxide contain Pu[V], which is in agreement with the thermodynamic predictions. Although this method could not be used conclusively with the remaining solutions ( -5 4 M Pu) contacting 239 Pu[IV] hydroxide and 239 PuO 2 , the solvent extraction and Eh-pH results are similar for all the samples suggesting the strong possibility that all samples contain Pu[V]. Thus the possibility, ignored in the past, that Pu[V] may be the dominant species in relatively oxidizing environments should be considered

Plutonium diffusion in advanced fuels (U,Pu)(C,O) and (U,Pu)(C,N)

International Nuclear Information System (INIS)

Bradbury, M.H.; Matzke, H.

1983-01-01

The self-diffusion of 238 Pu was measured in an oxicarbide (U,Pu)(C,O) and a carbonitride (U,Pu) (C,N). The activation enthalpies were 447 and 347 kJ mol -1 , respectively. The carbonitrides were confirmed to fall into three classes: carbide-like compositions with less than 30% nitrogen in the metalloid lattice, nitride-like composition with more than 70% nitrogen and with reduced atomic mobilities, and carbonitrides with about 50% nitrogen showing an intermediate behavior. The oxicarbide showed diffusion coefficients slightly larger than those of pure carbides

Use of combined alpha-spectrometry and fission track analysis for the determination of 240Pu/239Pu ratios in human tissue

International Nuclear Information System (INIS)

Love, S.F.; Filby, R.H.; Glover, S.E.; Stuit, D.B.; Kathren, R.L.

1998-01-01

Plutonium and other actinides were determined in human autopsy tissues of occupationally exposed workers who were registrants of the United States Transuranium and Uranium Registries (USTUR). In this study, Pu was purified and isolated from Am, U and Th, after drying and wet-ashing of the tissues, and the addition of 238 Pu as a radiotracer. After electrodeposition onto vanadium planchets, the 239+240 Pu activity was determined by alpha-spectrometry. A fission track method was developed to determine 239 Pu in the presence of 238 Pu and 240 Pu, using Lexan TM polycarbonate detectors. Combining the two techniques allowed the determination of the 240 Pu/ 239 Pu activity and atom ratios. Data from selected USTUR cases are presented. (author)

Electronic structure of Pu-Ce(-Ga) and Pu-Am(-Ga) alloys, stabilized in the {delta} phase; Structure electronique d'alliages Pu-Ce(-Ga) et Pu-Am(-Ga) stabilises en phase {delta}

Energy Technology Data Exchange (ETDEWEB)

Dormeval, M

2001-09-01

The behaviour of {delta}-plutonium, stable between 319 and 451 deg C, exhibits numerous singularities which are still a mystery for both physicists and metallurgists. This is due to its complex electronic structure, and in particular to the 5f electrons, which are at the edge between localization and delocalization. The stability domain of the {delta} phase can be extended down to room temperature by alloying with so called 'deltagen atoms' such as gallium (Ga), aluminum (A1), cerium (Ce) or americium (Am). The present work deals, one the one hand, with the influence of cerium and americium solutes regarding the localization of the 5f electrons of {delta}-plutonium, in binary Pu-Ce and Pu-Am alloys. On the other hand, the effect of two different deltagen solutes, simultaneously present, on the stability of the {delta} phase has been studied in ternary Pu-Am-Ga and Pu-Ce-Ga alloys. The electronic structure being strongly related to the crystalline organization, characterization methods such as X-Ray diffraction and EXAFS measurements were used together with electrical resistivity and magnetic susceptibility experiments. These showed that the roles of cerium and americium, supposed to be similar at the beginning of this investigation, are actually very different. Moreover, the additive effect of cerium and gallium, and, americium and gallium, has been demonstrated. Studying plutonium alloys, which are radioactive, also means following their evolution in time. The characteristics of the alloys have then been followed which allowed to detect, in Pu-Ce(-Ga) alloys, a destabilization of the {delta} phase and, to observe, in Pu-Am(-Ga) alloys, the influence of self-irradiation defects on the magnetic response. (author)

Vertical profiles of 239(240)Pu, 238Pu and 241Am in some peculiar Italian mosses

International Nuclear Information System (INIS)

Testa, C.; Desideri, D.; Guerra, F.; Meli, M.A.; Roselli, C.; Jia, G.; Degetto, S.

2000-01-01

During the last two years the Urbino University and the Padua ICTIMA CNR were working on a special radioecological program having the aim to study the Pu and Am retention behaviour in different species of mosses growing in two Italian regions (Urbino, Central Italy, 450 m a.s.l. and Alps region, Northern Italy, 1500 m a.s.l.). 239,240 Pu, 238 Pu and 241 Am were separated and determined by extraction chromatography, electroplating and alpha spectrometry; 242 Pu and 243 Am were used as the yield tracers. The paper summarizes the results dealing with the vertical profiles of the radionuclides in three different species of mosses. Several 1-2 cm high sections were obtained and dated by 210 Pb determination. Typical concentration peaks for Pu and Am were found for very old moss species ('Sphagnum Compactum' and 'Sphagnum Nemoreum') at a depth corresponding to the early 1960's which is the period characterized by the maximum nuclear weapon tests. In more recent moss species ('Neckeria Crispa') no peak was observed and the regression curves showed that Am is more mobile than Pu. (author)

Risk estimates for lung tumours from inhaled 239PuO2, 238PuO2, and 239Pu(NO3)4 in beagle dogs

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.; Gilbert, E.S.; Weller, R.E.

1989-01-01

Lung cancer risks are being studied in beagle dogs given single exposures to aerosols of 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 . A major objective of these studies is to examine the risk of lung cancer relative to the specific activity of the radionuclide, rate of dose accumulation due to differences in solubilities of the radionuclides, and the presence of competing risk from extrapulmonary lesions. Dose-response relationships were studied for the three groups of dogs, with analyses specifically designed to evaluate differences in response. Based on estimated cumulative dose to the lung, risks were found to differ significantly among the radionuclides; they were highest for 239 Pu(NO 3 ) 4 and lowest for 238 PuO 2 . A model in which the risk was assumed to be a pure quadratic function of dose fitted the data much better than a pure linear model. Currently, all three groups of dogs can be compared only to 10 years after exposure. However, it is apparent that the average cumulative dose to the lung may not be an adequate predictor of lung cancer risk for different isotopic and physicochemical forms of plutonium. (author)

HPLC method for determination of Th, U and Pu in irradiated (Th,Pu)O{sub 2} using mandelic acid as an eluent

Energy Technology Data Exchange (ETDEWEB)

Kumar, Pranaw; Paul, Sumana; Jaison, Perumpillil George; Telmore, Vijay Madhukar; Alamelu, Devanathan; Aggarwal, Suresh Kumar [Bhabha Atomic Research Centre, Mumbai (India). Fuel Chemistry Div.

2014-07-01

Studies for chromatographic separation of Th, U(VI) and Pu(IV) were carried out using mandelic acid as an eluent. The different chromatographic conditions like concentration of mandelic acid, pH of the mobile phase, presence of MeOH and effect of ion interaction reagent (IIR) were studied. The method was optimized for the separation of Th, U(VI) and Pu(IV). At pH<3.5 of mobile phase, Pu(IV) was more retained compared to U(VI) whereas at pH>3.5, reverse trend was observed. The optimized parameters were employed for the separation and determination of Th, U(VI) and Pu(IV) in a dissolved solution of irradiated (Th,Pu)O{sub 2}. Sample treatment was optimized to minimize loss of Pu and Th during chromatographic determination. Studies were carried out using two IIRs to understand the anomalous chromatographic behavior of Pu(IV). Retention behavior of different oxidation states of Pu viz. Pu(III), Pu(IV) and Pu(VI) was also studied in mandelic acid.

Unsafe Coulomb excitation of $^{240-244}Pu$

CERN Document Server

Wiedenhöver, I; Hackman, L; Ahmad, I; Greene, J P; Amro, H; Carpenter, M P; Nisius, D T; Reiter, P; Lauritsen, T; Lister, C J; Khoo, T L; Siem, S; Cizewski, J A; Seweryniak, D; Uusitalo, J; Macchiavelli, A O; Chowdhury, P; Seabury, E H; Cline, D; Wu, C Y

1999-01-01

The high spin states of /sup 240/Pu and /sup 244/Pu have been investigated with GAMMASPHERE at ATLAS, using Coulomb excitation with a /sup 208/Pb beam at energies above the Coulomb barrier. Data on a transfer channel leading to /sup 242/Pu were obtained as well. In the case of /sup 244/Pu, the yrast band was extended to 34h(cross), revealing the completed pi i/sub 13/2/ alignment, a "first" for actinide nuclei. The yrast sequence of /sup 242/Pu was also extended to higher spin and a similar backbend was delineated. In contrast, while the ground state band of /sup 240/Pu was measured up to the highest rotational frequencies ever reported in the actinide region (~300 keV), no sign of particle alignment was observed. (11 refs).

Validación de la precipitación estimada por satélite TRMM y su aplicación en la modelación hidrológica del rio Ramis Puno Perú

OpenAIRE

Lujano Laura, Efrain; Servicio Nacional de Meteorología e Hidrología; Felipe Obando, Oscar G.; Servicio Nacional de Meteorología e Hidrología; Lujano Laura, Apolinario; Quispe Aragón, José; Autoridad Nacional del Agua

2015-01-01

La investigación se realizó en la cuenca Ramis, ubicado al norte de la región hidrográfica del Titicaca (lado peruano), teniendo como objetivo validar las precipitaciones estimadas por satélite y su aplicación en la modelación hidrológica del rio Ramis. La validación de precipitaciones estimadas por satélite, se realizó mediante una comparación entre datos observados en ambos casos para el periodo enero de 1998 a diciembre 2013, los cuales fueron evaluados mediante los indicadores estadístico...

Structural, magnetic, electronic and optical properties of PuC and PuC{sub 0.75}: A hybrid density functional study

Energy Technology Data Exchange (ETDEWEB)

Yang, Rong [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); College of Materials Science and Engineering, Chongqing Jiaotong University, Chongqing 400074 (China); Tang, Bin [School of Business Administration, Chongqing City Management College, Chongqing 401331 (China); Gao, Tao, E-mail: gaotao@scu.edu.cn [Institute of Atomic and Molecular Physics, Sichuan University, Chengdu 610065 (China); Ao, BingYun, E-mail: aobingyun@caep.cn [Science and Technology on Surface Physics and Chemistry Laboratory, P.O. Box 718-35, Mianyang 621907 (China)

2016-05-15

We perform first principles calculations to investigate the structural, magnetic, electronic and optical properties of PuC and PuC{sub 0.75}. Furthermore, we examine the influence of carbon non-stoichiometry on plutonium monocarbide. For the treatment of strongly correlated electrons, the hybrid density functionals like PBE0, Fock-0.25 are used and we compare the results with the generalized gradient approximation (GGA), local density approximation (LDA), LDA + U and experimental ones. The optimized lattice constant a{sub 0} = 4.961 Å for PuC in the Fock-0.25 scheme is the most close to the experimental data. The ground states of PuC and PuC{sub 0.75} are found to be anti-ferromagnetic. Our results indicate that additional removal of a C atom make lattice contract and new DOS peak appear in the near-Fermi region. We also compute and compare the optical properties of PuC and PuC{sub 0.75}. The difference in optical properties between PuC and PuC{sub 0.75} should also be the influence of carbon vacancies.

Isolation, identification, and environmental adaptability of heavy-metal-resistant bacteria from ramie rhizosphere soil around mine refinery

OpenAIRE

Jiang, Jie; Pan, Chaohu; Xiao, Aiping; Yang, Xiai; Zhang, Guimin

2017-01-01

Six bacteria strains from heavy-metal-polluted ramie rhizosphere soil were isolated through Cd2+ stress, which were numbered as JJ1, JJ2, JJ10, JJ11, JJ15, and JJ18. Sequence alignment and phylogenic analysis showed that strain JJ1 belonged to Pseudomonas, strain JJ2 belonged to Cupriavidus, strains JJ11 and JJ15 belonged to Bacillus, and strains JJ10 and JJ18 belonged to Acinetobacter. The tolerance capability of all the strains was the trend of Pb2+?>?Zn2+?>?Cu2+?>?Cd2+, the maximum toleran...

Uudised : RAMi lauljad Iisraelis. Lauluvõistlus Pärnus. Wagner, ka Eestis. Juuniküüditamise mälestuskontsert / Joosep Sang

Index Scriptorium Estoniae

Sang, Joosep

2001-01-01

Osa RAMi lauljaist osaleb Tel Avivis Iisraeli Uue Ooperi etendustel, B.Britteni ooperi "Billy Budd" lavastuses. Pärnus 2.-6. mail toimunud II Klaudia Taevi nim. noorte lauljate konkursi tulemustest. 17. mail EMAs toimuvast teaduskonverentsist "Richard Wagner, ka Eestis", 18. mail toimuvast galakontserdist ja näituse "Wagner Eesti laval" avamisest Estonia kontserdisaalis. 15. mail Narvas ja 16. mail Rakveres toimuvast Mozarti "Reekviemi" ettekandest juuniküüditamise mälestuseks

Cation interdiffusion in the UO2 - (U, Pu)O2 and UO2 - PuO2 systems

International Nuclear Information System (INIS)

Leme, D.G.

1985-01-01

The interdiffusion of U and Pu ions in UO sub(2 +- x) - (U sub(0,83) Pu sub(0,17))O sub(2 + - x) and UO sub(2 + - x) -PuO sub(2 - x) sintered pellets and UO sub(2 +- x) -(U sub(0,82) Pu sub(0,18))O sub(2 + - x) single crystals has been studied as a function of the oxygen potential ΔG sup(-) (O 2 ) or the stoichiometric ratio O/M. The diffusion profiles of UO 2 /(U,Pu)O 2 and UO 2 /PuO 2 couples of different O/M ratios have been measured using high resolution α-spectrometer and microprobe. Thermal annealing of the specimens was performed in controlled atmospheres using either CO-CO 2 gas mixtures for constant O/M ratios or purified argon. The interdiffusion profiles have been analysed by means of the Boltzmann-Matano and Hall methods. The interdiffusion coefficient D sus(approx.) increases with increasing Pu content in sintered pellets (up to 17 wt. %PuO 2 ) showing a strong dependence of D sup(approx.) on the O/M ratio. The micropobe results show that the interdiffusion along grain boundaries is the main diffusion mechanism in the pellets. Experiments have also been carried out in single cristals to measure just the bulk-interdiffusion and avoiding effects due to grain boundaries. A marked dependence of D sup(approx.) on O/M ratio or on oxygen potential ΔG sup(-) (O 2 ), similar to the dependence already reported for self diffusion by means of radioactive tracers, has also been observed. (Author) [pt

Modeling water permeability in needle-punched nonwovens using finite element analysis

CSIR Research Space (South Africa)

Patanaik, A

2008-03-01

Full Text Available and it is then removed by pressurized non- reacting gas (air) to give pore size and its distribution. Three kinds of pores may be present in nonwoven fabrics, namely, closed pores, through pores, and blind pores. Closed pores are not accessible and therefore do... not allow passage of liquid and air. The blind pores terminate inside the material and do not permit the fluid flow. Through pores are open and allow the flow through the medium and they are important for filtration and drainage applications [8...

Electronic structure of Pu-Ce(-Ga) and Pu-Am(-Ga) alloys, stabilized in the {delta} phase; Structure electronique d'alliages Pu-Ce(-Ga) et Pu-Am(-Ga) stabilises en phase {delta}

Energy Technology Data Exchange (ETDEWEB)

Dormeval, M

2001-09-01

The behaviour of {delta}-plutonium, stable between 319 and 451 deg C, exhibits numerous singularities which are still a mystery for both physicists and metallurgists. This is due to its complex electronic structure, and in particular to the 5f electrons, which are at the edge between localization and delocalization. The stability domain of the {delta} phase can be extended down to room temperature by alloying with so called 'deltagen atoms' such as gallium (Ga), aluminum (A1), cerium (Ce) or americium (Am). The present work deals, one the one hand, with the influence of cerium and americium solutes regarding the localization of the 5f electrons of {delta}-plutonium, in binary Pu-Ce and Pu-Am alloys. On the other hand, the effect of two different deltagen solutes, simultaneously present, on the stability of the {delta} phase has been studied in ternary Pu-Am-Ga and Pu-Ce-Ga alloys. The electronic structure being strongly related to the crystalline organization, characterization methods such as X-Ray diffraction and EXAFS measurements were used together with electrical resistivity and magnetic susceptibility experiments. These showed that the roles of cerium and americium, supposed to be similar at the beginning of this investigation, are actually very different. Moreover, the additive effect of cerium and gallium, and, americium and gallium, has been demonstrated. Studying plutonium alloys, which are radioactive, also means following their evolution in time. The characteristics of the alloys have then been followed which allowed to detect, in Pu-Ce(-Ga) alloys, a destabilization of the {delta} phase and, to observe, in Pu-Am(-Ga) alloys, the influence of self-irradiation defects on the magnetic response. (author)

Development of an U and Pu recovery process by molten salt electrorefining. Behavior of U and Pu at simultaneous recoveries into liquid cadmium cathodes

International Nuclear Information System (INIS)

Uozumi, Koichi; Kato, Tetsuya; Iizuka, Masatoshi; Inoue, Tadashi; Iwai, Takashi; Shirai, Osamu; Arai, Yasuo

2003-01-01

In order to study behaviors of U and Pu at simultaneous recoveries into liquid cadmium cathodes (LCCs) in the electrorefining of pyrometallurgical reprocessing, several experiments were conducted to recover U and Pu into LCCs at different U/Pu ratios in the salt phase. The major results were as follows: (1) The weight ratios of U and Pu in 120 g LCCs reached 10 wt.% (the tentative target), with current efficiencies higher than 80 %. (2) Under the conditions of U/Pu ratios in the initial salt phase less than 1/4.3, the amounts of recovered U and Pu were proportional to the passed electric charges, with the separation factors of U to Pu (= (U/Pu ration in the recovered product)/(U/Pu ratio in the salt)) between 1.2 and 2.0. (3) On the other hand, under the condition of U/Pu ratio in the initial salt phase at 1/1.73, only U was recovered into the LCC after the saturation of LCC with U and Pu. Accordingly, there will be a threshold in the U/Pu ratio of the salt phase for the simultaneous recovery of U and Pu. (4) Am showed a similar behavior to Pu. The separation factors of Am to Pu (=(AM/Pu ratio in the recovered product)/(Am/Pu ratio in the salt)) was 0.78, which means that Am is co-recovered with Pu into LCC. (author)

Deposition of Pu-239 in human bodies

International Nuclear Information System (INIS)

Okabayashi, Hiroyuki

1976-01-01

It is known that plutonium produced by nuclear explosion tests has been widely dispersed on all over the earth and Pu-238 generated by the ''Accident of SNAP-9A'' in 1964 has been disposed into the atmosphere. These Pu are gradually falling down on the earth and taken into the human body through inhalation and ingestion. The measurements on the concentrations of Pu in bones and other various organs of Japanese population have been carried out. The results reveal that the concentrations of Pu in bones has a trend to be gradually increasing since 1962 and seems to be saturated at about 1970. The concentrations of Pu in bones sampled in 1971 are, in average, in the level of 4fCi per gram of wet samples and those in other organs (lung, liver, spleen, kidney, reproductive organs, etc.) sampled from 1963 to 1973 are in the level of 0.5-3.4 fCi per gram of wet tissues. Pu has been identified in the bones of fetus and infants and the averaged concentrations of placenta was 42.5 fCi. These may indicate that Pu would be transferred to the fetus through the placenta of mother. Some calculation has been attempted on the ratio of contributions through inhalation and ingestion to the body content of Pu, by using the formula for the scheme of metabolism of Pu compound in the body recommended by I.C.R.P. and this revealed that the contribution through inhalation route seemed to be greater than the other for the accumulation of Pu in the body. (auth.)

Determination of Plutonium Activity Concentrations and 240Pu/239Pu Atom Ratios in Brown Algae (Fucus distichus) Collected from Amchitka Island, Alaska

International Nuclear Information System (INIS)

Hamilton, T F; Brown, T A; Marchetti, A A; Martinelli, R E; Kehl, S R

2005-01-01

Plutonium-239 ( 239 Pu) and plutonium-240 ( 240 Pu) activity concentrations and 240 Pu/ 239 Pu atom ratios are reported for Brown Algae (Fucus distichus) collected from the littoral zone of Amchitka Island (Alaska) and at a control site on the Alaskan peninsula. Plutonium isotope measurements were performed in replicate using Accelerator Mass Spectrometry (AMS). The average 240 Pu/ 239 Pu atom ratio observed in dried Fucus d. collected from Amchitka Island was 0.227 ± 0.007 (n=5) and compares with the expected 240 Pu/ 239 Pu atom ratio in integrated worldwide fallout deposition in the Northern Hemisphere of 0.1805 ± 0.0057 (Cooper et al., 2000). In general, the characteristically high 240 Pu/ 239 Pu content of Fucus d. analyzed in this study appear to indicate the presence of a discernible basin-wide secondary source of plutonium entering the marine environment. Of interest to the study of plutonium source terms within the Pacific basin are reports of elevated 240 Pu/ 239 Pu atom ratios in fallout debris from high-yield atmospheric nuclear tests conducted in the Marshall Islands during the 1950s (Diamond et al., 1960), the wide range of 240 Pu/ 239 Pu atom ratio values (0.19 to 0.34) observed in sea water, sediments, coral and other environmental media from the North Pacific Ocean (Hirose et al., 1992; Buesseler, 1997) and updated estimates of the relative contributions of close-in and intermediate fallout deposition on oceanic inventories of radionuclidies, especially in the Northern Pacific Ocean (Hamilton, 2004)

Processing and Characterization of a Novel Distributed Strain Sensor Using Carbon Nanotube-Based Nonwoven Composites

Directory of Open Access Journals (Sweden)

Hongbo Dai

2015-07-01

Full Text Available This paper describes the development of an innovative carbon nanotube-based non-woven composite sensor that can be tailored for strain sensing properties and potentially offers a reliable and cost-effective sensing option for structural health monitoring (SHM. This novel strain sensor is fabricated using a readily scalable process of coating Carbon nanotubes (CNT onto a nonwoven carrier fabric to form an electrically-isotropic conductive network. Epoxy is then infused into the CNT-modified fabric to form a free-standing nanocomposite strain sensor. By measuring the changes in the electrical properties of the sensing composite the deformation can be measured in real-time. The sensors are repeatable and linear up to 0.4% strain. Highest elastic strain gage factors of 1.9 and 4.0 have been achieved in the longitudinal and transverse direction, respectively. Although the longitudinal gage factor of the newly formed nanocomposite sensor is close to some metallic foil strain gages, the proposed sensing methodology offers spatial coverage, manufacturing customizability, distributed sensing capability as well as transverse sensitivity.

Determination of Pu in soil samples

International Nuclear Information System (INIS)

Torres C, C. O.; Hernandez M, H.; Romero G, E. T.; Vega C, H. R.

2016-10-01

The irreversible consequences of accidents occurring in nuclear plants and in nuclear fuel reprocessing sites are mainly the distribution of different radionuclides in different matrices such as the soil. The distribution in the superficial soil is related to the internal and external exposure to the radiation of the affected population. The internal contamination with radionuclides such as Pu is of great relevance to the nuclear forensic science, where is important to know the chemical and isotopic compositions of nuclear materials. The objective of this work is to optimize the radiochemical separation of plutonium (Pu) from soil samples and to determine their concentration. The soil samples were prepared using acid digestion assisted by microwave; purification of Pu was carried out with AG1X8 resin using ion exchange chromatography. Pu isotopes were measured using ICP-SFMS. In order to reduce the interference due to the presence of "2"3"8UH "+ in the samples, a solvent removal system (Apex) was used. In addition, the limit of detection and quantification of Pu was determined. It was found that the recovery efficiency of Pu in soil samples ranges from 70 to 93%. (Author)

Flexible, Heat-Resistant, and Flame-Retardant Glass Fiber Nonwoven/Glass Platelet Composite Separator for Lithium-Ion Batteries

Directory of Open Access Journals (Sweden)

Ulrich Schadeck

2018-04-01

Full Text Available A new type of high-temperature stable and self-supporting composite separator for lithium-ion batteries was developed consisting of custom-made ultrathin micrometer-sized glass platelets embedded in a glass fiber nonwoven together with a water-based sodium alginate binder. The physical and electrochemical properties were investigated and compared to commercial polymer-based separators. Full-cell configuration cycling tests at different current rates were performed using graphite and lithium iron phosphate as electrode materials. The glass separator was high-temperature tested and showed a stability up to at least 600 °C without significant shrinking. Furthermore, it showed an exceptional wettability for non-aqueous electrolytes. The electrochemical performance was excellent compared to commercially available polymer-based separators. The results clearly show that glass platelets integrated into a glass fiber nonwoven performs remarkably well as a separator material in lithium-ion batteries and show high-temperature stability.

Safety requirements for the Pu carriers

International Nuclear Information System (INIS)

Mishima, H.

1993-01-01

Ministry of Transport of Japan has now set about studying requirements for Pu carriers to ensure safety. It was first studied what the basic concept of safe carriage of Pu should be, and the basic ideas have been worked out. Next the requirements for the Pu carriers were studied based on the above. There are at present no international requirements of construction and equipment for the nuclear-material carriers, but MOT of Japan has so far required special construction and equipment for the nuclear-material carriers which carry a large amount of radioactive material, such as spent fuel or low level radioactive waste, corresponding to the level of the respective potential hazard. The requirements of construction and equipment of the Pu carriers have been established considering the difference in heat generation between Pu and spent fuel, physical protection, and so forth, in addition to the above basic concept. (J.P.N.)

Transmutation of 129I, 237Np, 238Pu, 239Pu, and 241Am using ...

Indian Academy of Sciences (India)

Results of transmutation studies of 129I, 237Np, 238Pu, 239Pu and 241Am are presented. Keywords. ... J Adam et al. Table 1. Samples properties for 0.7 and 1 GeV experiments. ..... If we suppose that this conclusion is true also for ratios in ...

Study of U - Pu - Fe alloys (Masurca critical experiment); Etudes d'alliages U-Pu-Fe (experience critique MASURCA)

Energy Technology Data Exchange (ETDEWEB)

Barthelemy, P; Boucher, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-07-01

Three compositions have been studied: 73.5 U - 25 Pu - 1.5 Fe (weight %) 74 U - 25 Pu - 1 Fe 74.5 U - 25 Pu - 0.5 Fe Elaboration and Casting are easy. After two weeks in air 74.5 U - 25 Pu - 0.5 Fe alloys are reduced in powder. As-cast alloys containing 1 and 1,5% Fe are kept undamaged during several months. A rapid oxidisation of the alloys is however observed when the samples undergo the phase transformation (at 595 deg. C and 590 deg. C respectively). Ignition tests in the presence of air show that the oxidisation starts at about 250 deg. C and that the reaction does not spread. Ignition is not observed during heating from 20 to 660 deg. C. The transformation temperature, the melting temperature and the thermal expansion coefficients have been determined by dilatometry. Below the transformation temperature, the principal phases are U-Pu zeta and (U, Pu){sub 6}Fe. Thermal conductibility, Young modulus, density and heat of fusion have been measured. Compatibility tests show that between U-Pu-Fe and stainless steel a phase of (U, Pu){sub 6}Fe type is formed. The 74 U - 25 Pu - 1% Fe alloy seems to behave better than 73.5 U - 25 Pu - 1.5% Fe alloy because the (U, Pu){sub 6}Fe layer is two or three times smaller. Finally, the thermal stability has been studied with the 74 U - 25 Pu - 1% Fe alloy. A dilatometric anomaly (very weak expansion) occurs when the sample is heated above transformation temperature and cooled. But there is no anomaly by thermal cycling from 50 deg. C to 400 deg. C and there is no deterioration of alloys by heat treatments at 100 deg. C, 200 deg. C, 300 deg. C during 5 months under vacuum. (authors) [French] Trois compositions ont ete etudiees: 73,5 U - 25 Pu - 1,5 Fe (% ponderaux) 74 U - 25 Pu - 1 Fe 74,5 U - 25 Pu - 0,5 Fe Les elaborations et mises en forme sont-faciles. Les alliages a 0,5% de fer tombent en poudre apres 15 jours d'exposition a l'air. Les alliages a 1 et 1,5% de fer, bruts de coulee, se conservent plusieurs mois. Cependant

ZPR-6 assembly 7 high {sup 240}Pu core experiments : a fast reactor core with mixed (Pu,U)-oxide fuel and a centeral high{sup 240}Pu zone.

Energy Technology Data Exchange (ETDEWEB)

Lell, R. M.; Morman, J. A.; Schaefer, R.W.; McKnight, R.D.; Nuclear Engineering Division

2009-02-23

ZPR-6 Assembly 7 (ZPR-6/7) encompasses a series of experiments performed at the ZPR-6 facility at Argonne National Laboratory in 1970 and 1971 as part of the Demonstration Reactor Benchmark Program (Reference 1). Assembly 7 simulated a large sodium-cooled LMFBR with mixed oxide fuel, depleted uranium radial and axial blankets, and a core H/D near unity. ZPR-6/7 was designed to test fast reactor physics data and methods, so configurations in the Assembly 7 program were as simple as possible in terms of geometry and composition. ZPR-6/7 had a very uniform core assembled from small plates of depleted uranium, sodium, iron oxide, U{sub 3}O{sub 8} and Pu-U-Mo alloy loaded into stainless steel drawers. The steel drawers were placed in square stainless steel tubes in the two halves of a split table machine. ZPR-6/7 had a simple, symmetric core unit cell whose neutronic characteristics were dominated by plutonium and {sup 238}U. The core was surrounded by thick radial and axial regions of depleted uranium to simulate radial and axial blankets and to isolate the core from the surrounding room. The ZPR-6/7 program encompassed 139 separate core loadings which include the initial approach to critical and all subsequent core loading changes required to perform specific experiments and measurements. In this context a loading refers to a particular configuration of fueled drawers, radial blanket drawers and experimental equipment (if present) in the matrix of steel tubes. Two principal core configurations were established. The uniform core (Loadings 1-84) had a relatively uniform core composition. The high {sup 240}Pu core (Loadings 85-139) was a variant on the uniform core. The plutonium in the Pu-U-Mo fuel plates in the uniform core contains 11% {sup 240}Pu. In the high {sup 240}Pu core, all Pu-U-Mo plates in the inner core region (central 61 matrix locations per half of the split table machine) were replaced by Pu-U-Mo plates containing 27% {sup 240}Pu in the plutonium

Distribution of 238Pu and 239240Pu in aquatic macrophytes from a midwestern watershed

International Nuclear Information System (INIS)

Wayman, C.W.; Bartelt, G.E.; Alberts, J.J.

1977-01-01

Aquatic macrophytes were collected in the Great Miami River, Ohio, above and below Miamisburg and in the canal and ponds, near the Mound Laboratory, which contain sediments of a high activity (approximately 10 3 to 10 6 times) relative to the river sediments. Macrophytes collected in the river below Miamisburg have higher activities of 238 Pu than those collected from above the city. Macrophytes from the canal and ponds contain high specific activities of 238 Pu and 239 , 240 Pu with the exception of cattails grown in the ponds. Concentration factors are reported and discussed with reference to possible modes of plutonium accumulation and distribution within the plants

Neutron inelastic-scattering cross sections of 232Th, 233U, 235U, 238U, 239Pu and 240Pu

International Nuclear Information System (INIS)

Smith, A.B.; Guenther, P.T.

1982-01-01

Differential-neutron-emission cross sections of 232 Th, 233 U, 235 U, 238 U, 239 Pu and 240 Pu are measured between approx. = 1.0 and 3.5 MeV with the angle and magnitude detail needed to provide angle-integrated emission cross sections to approx. 232 Th, 233 U, 235 U and 238 U inelastic-scattering values, poor agreement is observed for 240 Pu, and a serious discrepancy exists in the case of 239 Pu

Measurement of oxygen chemical diffusion in PuO2-x and analysis of oxygen diffusion in PuO2-x and (Pu,U)O2-x

International Nuclear Information System (INIS)

Kato, Masato; Uchida, Teppei; Sunaoshi, Takeo

2013-01-01

Oxygen chemical diffusion in PuO 2-x was investigated in the temperature range of 1473-1873 K by thermogravimetry as functions of oxygen-to-metal (O/M) ratios and temperatures. The oxygen chemical diffusion coefficients, D were determined assuming that the reduction curves were dominated by a diffusion process. The O/M ratio and Pu content dependence on the chemical diffusion coefficients were evaluated. The chemical diffusion coefficient had its minimum value at around O/M=1.98 and decreased with increasing Pu content in (U,Pu)O 2-x . The self-diffusion coefficients were evaluated. A model for describing the relationship among O/M ratio, oxygen chemical diffusion, and self-diffusion was proposed based on defect chemistry. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Determination of 239Pu/240Pu isotopic ratio by high resolution alpha-particle spectrometry

International Nuclear Information System (INIS)

Amoudry, F.; Burger, P.

1983-05-01

The development of passivated ion-implanted silicon detectors and of very thin alpha-particle sources improves the resolution of alpha-particle spectra and allows to separate energy pics up to now unseparate. The 239 Pu/ 240 Pu isotopic ratio of a mixture has been measured using the alpha spectrometry deconvolution code DEMO [fr

Role of surface energy and nano-roughness in the removal efficiency of bacterial contamination by nonwoven wipes from frequently touched surfaces

Science.gov (United States)

Edwards, Nicholas W. M.; Best, Emma L.; Connell, Simon D.; Goswami, Parikshit; Carr, Chris M.; Wilcox, Mark H.; Russell, Stephen J.

2017-12-01

Healthcare associated infections (HCAIs) are responsible for substantial patient morbidity, mortality and economic cost. Infection control strategies for reducing rates of transmission include the use of nonwoven wipes to remove pathogenic bacteria from frequently touched surfaces. Wiping is a dynamic process that involves physicochemical mechanisms to detach and transfer bacteria to fibre surfaces within the wipe. The purpose of this study was to determine the extent to which systematic changes in fibre surface energy and nano-roughness influence removal of bacteria from an abiotic polymer surface in dry wiping conditions, without liquid detergents or disinfectants. Nonwoven wipe substrates composed of two commonly used fibre types, lyocell (cellulosic) and polypropylene, with different surface energies and nano-roughnesses, were manufactured using pilot-scale nonwoven facilities to produce samples of comparable structure and dimensional properties. The surface energy and nano-roughness of some lyocell substrates were further adjusted by either oxygen (O2) or hexafluoroethane (C2F6) gas plasma treatment. Static adpression wiping of an inoculated surface under dry conditions produced removal efficiencies of between 9.4% and 15.7%, with no significant difference (p < 0.05) in the relative removal efficiencies of Escherichia coli, Staphylococcus aureus or Enterococcus faecalis. However, dynamic wiping markedly increased peak wiping efficiencies to over 50%, with a minimum increase in removal efficiency of 12.5% and a maximum increase in removal efficiency of 37.9% (all significant at p < 0.05) compared with static wiping, depending on fibre type and bacterium. In dry, dynamic wiping conditions, nonwoven wipe substrates with a surface energy closest to that of the contaminated surface produced the highest E. coli removal efficiency, while the associated increase in fibre nano-roughness abrogated this trend with S. aureus and E. faecalis.

Characterization of a Pu-bearing zirconolite-rich synroc

International Nuclear Information System (INIS)

Buck, E.C.; Ebbinghaus, B.; Bakel, A.J.; Bates, J.K.

1996-01-01

A titanate-based ceramic waste form, rich in phases structurally related to zirconolite (CaZrTi 2 O 7 ), is being developed as a possible method for immobilizing excess plutonium from dismantled nuclear weapons. As part of this program, Lawrence Livermore National Laboratory (LLNL) produced several ceramics that were then characterized at Argonne National Laboratory (ANL). The plutonium- loaded ceramic was found to contain a Pu-Gd zirconolite phase but also contained plutonium titanates, Gd-polymignyte, and a series of other phases. In addition, much of the Pu was remained as PuO 2- x . The Pu oxidation state in the zirconolite was determined to be mainly Pu 4+ , although some Pu 3+ was believed to be present

Nitridation of U and Pu recovered in liquid Cd cathode by molten salt electrorefining of (U,Pu)N

Energy Technology Data Exchange (ETDEWEB)

Satoh, Takumi; Iwai, Takashi; Arai, Yasuo [Japan Atomic Energy Agency (Japan)

2009-06-15

Solid solutions of actinide mono-nitrides have been proposed as a candidate fuel of the accelerator-driven system (ADS) and Gen.IV-type fast reactors because the thermal conductivity and metal density are higher than those of actinide oxides and also they have high melting temperature. Pyrochemical process has several advantages over conventional wet process in treating of spent nitride fuel. One of the key technologies of the pyrochemical reprocessing of nitride fuel is the formation of the nitrides from actinides in the liquid Cd cathode. The nitridation-distillation combined method was developed and has been adopted to convert the actinides to the nitrides. In this method, the nitridation of actinides and the distillation of Cd occurred simultaneously by heating the actinide-Cd alloys in N{sub 2} gas stream. In the present study, the nitride formation behavior of U and Pu recovered in Cd cathode by molten salt electrorefining of (U,Pu)N was experimentally investigated. In addition, the nitride pellet was prepared form the powder obtained by the nitridation of U and Pu recovered in Cd cathode. (U,Pu)N (PuN = 80 mol %) was used as the starting material in the experiment. Molten salt electrorefining of (U,Pu)N pellet was carried out in the LiCl-KCl eutectic salt with 1.2 wt% PuCl{sub 3} and 0.3 wt% UCl{sub 3} of about 110 g at the constant anodic potential of -0.60 to -0.55 V vs. Ag/AgCl for about 9 hours at 773 K. After the electrorefining, about 42 % of U and Pu in the starting (U,Pu)N pellet was dissolved at the anode and recovered into the liquid Cd cathode. The recovered U-Pu-Cd alloy was heated in an alumina crucible at 973 K for 10 hours under N{sub 2} gas (99.999 %) stream (0.015 L/min). Fine black powder was recovered after heating the U-Pu-Cd alloy. The powder was identified as the single phase solid solution of (U,Pu)N by the XRD analysis. After milling in the agate mortar for 1 hour, the powder was compacted into green pellet under a pressure of about

Risk estimates for lung tumors from inhaled 239PuO2, 238PuO2, and /sup 239Pu/(NO3)4 in beagle dogs

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.; Gilbert, E.S.; Weller, R.E.

1988-06-01

Lung-cancer risks are being studied in beagle dogs given single exposures to aerosols of 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 . A major objective of these studies is to examine the risk of lung cancer relative to the specific activity of the radionuclide, rate of dose accumulation due to differences in solubilities of the radionuclides, and the presence of competing risk from extrapulmonary lesions. Dose-response relationships were studied for the three groups of dogs, with analyses specifically designed to evaluate differences in response. Based on estimated cumulative dose to the lung, risks were found to differ significantly among the radionuclides; they were highest for 239 Pu(NO 3 ) 4 and lowest for 238 PuO 2 . A model in which the risk was assumed to be a pure quadratic function of dose fit the data much better than a pure linear model. Currently, all three groups of dogs can be compared only to 10 years after exposure. However, it is apparent that the average cumulative dose to the lung may not be an adequate predictor of lung-cancer risk for different isotopic and physicochemical forms of plutonium. 13 refs., 2 tabs

Artificial radioactivity and marine environment. Study of 238Pu, 239Pu+240Pu, 241Pu and 241Am in the Mediterranean sea

International Nuclear Information System (INIS)

Ballestra, Serge.

1980-10-01

This paper is in two parts. Part one is about the methods for analyzing transuranium elements particularly the development of an analytical process for plutonium and for perfecting an Americium analyzing method, capable of treating samples of 200 litres of sea water, 100 grams of sediment and 100 grams of biological matter. Part two concerns the in situ determinations carried out within the scope of the study on the distribution and behaviour of transuranium elements in the Mediterranean sea. The high sea studies concerned the effects of atmospheric fall out and the vertical distribution of Pu and Am. Studies along the coasts enabled a quantitative study to be made of the contribution of rivers to the Mediterranean and to study the distribution of Pu along the French Mediterranean coast line [fr

Plutonium working reference materials for the NDA PDP program

International Nuclear Information System (INIS)

Marshall, R.; Foley, M.; McCullough, L.; Vance, D.

1995-01-01

Sixty-three QC standards, termed Working Reference Materials (WRMs) are being fabricated at Los Alamos for the Non-destructive Waste Assay Performance Development Plan. The WRMs require Pu and Am distributed uniformly in a low density matrix. A silicone rubber matrix initially specified has been changed to a packed, diatomaceous earth (DE) matrix to facilitate Pu-DE uniformity and minimize gas generation and WRM pressurization. Uniformity and separation stability was demonstrated with iron powder-DE mixtures. To meet the rigorous quality objectives on the mass of Pu and Am for each WRM, a uniform, stable batch of PuO2 with relatively high Am-241 content was prepared by blending, calcining, and screening. Multiple sample analyses demonstrated the PuO2 to be highly uniform and established that tight Pu and Am assay and Pu isotopic analysis precision requirements were met. Test blends were prepared and tested to successfully demonstrate Pu uniformity, freedom from PuO2 clumping, and acceptable alpha-neutron generation rates. Blends of PuO2-DE were prepared individually for each WRM; all 63 blends have been prepared. After loading and packing the blends into zircalloy cylinders, the air atmosphere will be replaced with helium and end caps inserted and welded. Following decontamination and leak checking, the cylinders will be loaded into secondary zircalloy cylinders and sealed with welded end caps

PU-ICE Summary Information.

Energy Technology Data Exchange (ETDEWEB)

Moore, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

The Generator Knowledge Report for the Plutonium Isentropic Compression Experiment Containment Systems (GK Report) provides information for the Plutonium Isentropic Compression Experiment (Pu- ICE) program to support waste management and characterization efforts. Attachment 3-18 presents generator knowledge (GK) information specific to the eighteenth Pu-ICE conducted in August 2015, also known as ‘Shot 18 (Aug 2015) and Pu-ICE Z-2841 (1).’ Shot 18 (Aug 2015) was generated on August 28, 2015 (1). Calculations based on the isotopic content of Shot 18 (Aug 2015) and the measured mass of the containment system demonstrate the post-shot containment system is low-level waste (LLW). Therefore, this containment system will be managed at Sandia National Laboratory/New Mexico (SNL/NM) as LLW. Attachment 3-18 provides documentation of the TRU concentration and documents the concentration of any hazardous constituents.

Micro-encapsulation of ozonated red pepper seed oil with antimicrobial activity and application to nonwoven fabric.

Science.gov (United States)

Özyildiz, F; Karagönlü, S; Basal, G; Uzel, A; Bayraktar, O

2013-03-01

In recent years, functional fabrics possessing antimicrobial activity have drawn significant interest because antibiotic resistance is becoming widespread among pathogenic micro-organisms. The aim of this study was to produce microcapsules incorporating ozonated red pepper seed oil (ORPSO) with antimicrobial properties and apply them to nonwoven fabrics to prepare functional textiles. Red pepper seed oil (RPSO) was ozonated and micro-encapsulated via a complex coacervation method using gelatin (GE) and gum arabic (GA) as wall materials. While micro-encapsulation yield and oil loading decreased with increases in the amount of surfactant, the mean particle size increased. The antimicrobial activity of the oil was tested via the disc diffusion method. The microcapsules were also tested using the agar well method. While RPSO had no effect on the test micro-organisms, the ORPSO and microcapsules containing ORPSO were found to be active against the test micro-organisms. The microcapsules were then applied to nonwoven fabric using the padding method to produce a disposable functional textile. The microcapsule-impregnated functional fabrics provided a 5 log decrease in 1 h. It is therefore possible to functionalize nonwoven fabrics to have antimicrobial activity against antibiotic-resistant micro-organisms, using microcapsules containing ORPSO. This is the first report on the antimicrobial action of RPSO after ozonation process. These findings suggest that ozonated red pepper seed oil (ORPSO) may be a useful and effective antimicrobial agent against the micro-organisms with antibiotic resistance. Therefore, as a natural product, RPSO represents a sustainable alternative to the use of synthetic antimicrobial agents. To our knowledge, this is also the first time that ORPSO has been micro-encapsulated for the preparation of functional textile material with significant antimicrobial activity. © 2012 The Society for Applied Microbiology.

Production of chitosan-based non-woven membranes using the electrospinning process

Science.gov (United States)

Pakravan Lonbani, Mehdi

Chitosan is a modified natural polymer mainly produced from chitin, one of the most abundant organic materials in the world. Highly porous chitosan mats present the specific physicochemical properties of the base material and also benefit from the physical characteristics of nanoporous membranes. Electrospinning is a novel technique developed long time ago and revisited recently that can generate polymeric fibers with nanometric size. The ultimate purpose of this work is to fabricate microporous non-woven chitosan membranes for wound healing dressings and heavy metal ion removal from drinking water. In this dissertation, two approaches have been utilized to prepare chitosan-based nanofibers; blending and co-axial electrospinning of chitosan solution with a readily electrospinnable solution, i.e. an aqueous solution of polyethylene oxide (PEO). Consequently, understanding the phase behavior and miscibility of aqueous acidic solutions of chitosan and PEO and their blends is of crucial importance, as any phase separation occurring during the electrospinning process greatly changes the morphology and physico-mechanical properties of the final products. First we employed the rheological approach on a well-known aqueous PEO solution to develop the experimental protocol. By comparing these critical points with that obtained from other experimental techniques, we showed that rheological measurements can sensitively detect early stages of phase separation. Subsequently the method was applied to 50 wt% aqueous acetic acid solutions of PEO, chitosan and their blends at different ratios. These solutions showed a lower critical solution temperature (LCST) phase diagram that is attributed to the existence of hydrogen bonds between active groups on chitosan and PEO backbone and the solvent. Critical decomposition temperatures for binodal and spinodal points were estimated from isochronal temperature sweep experiments. The obtained binodal temperatures confirmed that chitosan

Pu Denaturing by Transmutation of MA in FBR Multi-cycle

Energy Technology Data Exchange (ETDEWEB)

Meiliza, Yoshitalia; Saito, Masaki; Sagara, Hiroshi [Tokyo Institute of Technology, 2-12-1-N1-1 Ookayama, Meguro-ku, Tokyo, 1528550 (Japan)

2009-06-15

Pu accumulation and its recycling is important in the term of energy resources, however one of the most sensitive issues is non-proliferation in the future fuel cycle based on fast breeder reactor (FBR). The present paper utilizes Protected Pu Production (P{sup 3}) concept for the production of {sup 238}Pu and {sup 242}Pu by Minor Actinides (MA) transmutation to enhance the proliferation resistance of Pu in the fuel. Increase in the {sup 238}Pu and {sup 242}Pu isotopic fraction creates a high rate of internal heat generation by alpha decay (DH) and/or a high neutron source of spontaneous fission (SFN) in Pu that would be encountered during manufacturing and maintaining of nuclear explosive device. The feasibility of denaturing of Pu by MA transmutation in medium size FBR has been studied from the viewpoint of even-mass number Pu accumulation during multi-cycle of Pu and MA. The proliferation resistance property of Pu is also evaluated based on the specific decay heat and spontaneous fission neutron, compared with the reference criteria. In present paper, the P{sup 3} technology based on multi-recycled Pu and MA is compared with the conventional technology based on multi-recycled Pu only. The detail of mass balance behavior is, however, beyond the scope of the present paper. (authors)

Pu and Am determination in the environment method development

International Nuclear Information System (INIS)

Afonin, M.; Simonoff, M.; Donard, O.; Michel, H.; Ardisson, G.

2002-01-01

A few articles were published in the recent years regarding the application of ICP MS HR to the determination of ultratrace Pu in the environment. Si removal was not applied in recent publications. It is well known from marine biology that some microorganisms use Si derivatives in their metabolism. This implies that important amounts of Pu will not be dissolved and instead will rest in the solid residue. In our work we chose a combination of methods from EML-300 Handbook: Pu-02-RC Plutonium in Soil Samples, Pu-03-RC Plutonium in Soil Residue - Total Dissolution Method, Pu-11-RC Plutonium Purification - Ion Exchange Technique, Pu-12-RC Plutonium and/or Americium in Soil or Sediments. A high resolution inductively coupled plasma mass spectrometric method was developed for the determination of Am and the 240 Pu/ 239 Pu isotope ratio. The total plutonium concentrations ( 239+240 Pu) measured in environmental samples by this method were in good agreement with recommended data obtained from alpha-spectrometry. A reduction in the time of analysis over 33% was achieved

Spatial and temporal variations of plutonium isotopes (238Pu and 239,240Pu) in sediments off the Rhone River mouth (NW Mediterranean)

International Nuclear Information System (INIS)

Lansard, B.; Charmasson, S.; Gasco, C.; Anton, M.P.; Grenz, C.; Arnaud, M.

2007-01-01

The dispersion and fate of the Rhone River inputs to the Gulf of Lions (Northwestern Mediterranean Sea) have been studied through the spatial and temporal distributions of plutonium isotopes in continental shelf sediments. Plutonium isotopes ( 238 Pu and 239,240 Pu) are appropriate tracers to follow the dispersion of particulate matter due both to their high affinity for particles and their long half-lives. In the Rhone River valley, plutonium isotopes originate from both the weathering of the catchment basin contaminated by global atmospheric fallout, and the liquid effluents released from the Marcoule reprocessing plant since 1961. This work presents a first detailed study on 238 Pu and 239,240 Pu distributions in sediments from the Rhone prodelta to the adjacent continental shelf, since the decommissioning of Marcoule in 1997. The vertical distribution of Pu isotopes has been analysed in a 4.75 m long core sampled in 2001 at the Rhone mouth. Despite this length, plutonium is found at the last 10 cm, manifesting the high sedimentation rate of the prodeltaic area and its ability for trapping fine-grained sediments and associated contaminants. The highest 238 Pu and 239,240 Pu concentrations reached 1.26 and 5.97 Bq kg -1 respectively and were found within the layer 280-290 cm. The 238 Pu/ 239,240 Pu activity ratios (AR) demonstrated an efficient and huge trapping of the Pu isotopes derived from Marcoule. The fresh sediments, located on the top of the core, show lower plutonium activity concentrations and lower 238 Pu/ 239,240 Pu ratios. This decrease is in close relation with the shut down of the Marcoule reprocessing plant in 1997. In 2001, plutonium isotopes were also analysed in 21 surface sediments located offshore and concentrations ranged from 0.03 to 0.17 Bq kg -1 for 238 Pu and from 0.33 to 1.72 Bq kg -1 for 239,240 Pu. The 238 Pu/ 239,240 Pu AR ranged from 0.24 close to the river mouth to 0.06 southwards, indicating the decreasing influence of the

Structures and potential energy functions of Pu3 molecule

International Nuclear Information System (INIS)

Meng Daqiao; Jiang Gang; Liu Xiaoya; Luo Deli; Zhu Zhenghe

2001-01-01

Density functional (B3LYP) method with relativistic effective core potential (RECP) has been used to optimize the structures of Pu 2 and Pu 3 molecules. The results show that the ground states of Pu 2 and Pu 3 molecules are of D ∞h and D 3h symmetry, and of 13 and 19 fold, respectively. The spectral constants of Pu 2 , ω e = 52.3845 cm -1 and ω e x e = 0.0201 cm -1 , and the harmonic frequencies of Pu 3 , ν 1 = 56.9007 cm -1 , ν 2 = 57.1816 cm - '1 and ν 3 = 64.0785 cm -1 , have also been obtained on the B3LYP/RECP level. The potential energy functions of Pu 2 and Pu 3 have been derived, for the first time so far as known, from normal equation fitting and the many-body expansion theory

On the fission probability for 235U, 239Pu and 241Pu

International Nuclear Information System (INIS)

Benzi, V.; Maino, G.; Menapace, E.

1978-01-01

An evaluation of the GAMMAsub(n)/GAMMAsub(f) ratio for the 236 U, 240 Pu and 242 Pu compound nuclei is carried out. First chance and second chance fission cross sections are estimated from the ''evaporation'' model; particularly, a largely increasing trend was found for the first chance fission cross section above the (n,n'f) process threshold. The GAMMAsub(n)/GAMMAsub(f) ratios for the analyzed nuclei show a bump-like structure, that seems to be in agreement with the theoretical predictions reported in literature

Radiation protection problems with sealed Pu radiation sources

International Nuclear Information System (INIS)

Naumann, M.; Wels, C.

1982-01-01

A brief outline of the production methods and most important properties of Pu-238 and Pu-239 is given, followed by an overview of possibilities for utilizing the different types of radiation emitted, a description of problems involved in the safe handling of Pu radiation sources, and an assessment of the design principles for Pu-containing alpha, photon, neutron and energy sources from the radiation protection point of view. (author)

Dosimetry of 239Pu in dogs that inhaled monodisperse aerosols of 239PuO2

International Nuclear Information System (INIS)

Guilmette, R.A.; Muggenburg, B.A.; Hahn, F.F.; Mewhinney, J.A.; Seiler, F.A.; Boecker, B.B.; McClellan, R.O.

1987-01-01

Existing data from human exposure cases and experimental animal studies on the fate and dosimetry of inhaled insoluble Pu particles are inadequate to provide a comprehensive description and evaluation of the tissues at risk from the alpha radiations of Pu. To improve our knowledge of the dosimetry of inhaled insoluble 239 PuO 2 , this paper describes the uptake and retention of 239 Pu in the tissues of dogs that received single inhalation exposures to monodisperse aerosols of 239 PuO 2 . These data include times through 3 years after exposure. Using analytical functions fitted to each tissue data set, 1100-day radiation doses were calculated for lung, liver, skeleton, kidney, spleen, and tracheobronchial, mediastinal, sternal, hepatic, mandibular, and retropharyngeal lymph nodes. The dosimetry results suggest that the lung and lymph nodes associated with lymphatic drainage of the respiratory tract are the principal sites of alpha irradiation. However, the doses for the different respiratory tract lymph nodes vary by a factor of 2000, suggesting that assuming equivalent doses to respiratory tract lymph nodes is not appropriate. Other tissues receive radiation doses also but at levels one to three orders of magnitude less than the lung. Particle size dependence on uptake and retention was noted for the skeleton, mediastinal lymph nodes, hepatic lymph nodes, retropharyngeal lymph nodes, and mandibular lymph nodes

Calculation on maximum accumulation of Pu-239 and Pu-241 from aqueous homogeneous reactor

International Nuclear Information System (INIS)

Ikhlas H Siregar; Frida Agung R; Suharyana; Azizul Khakim; Dahman Siregar

2016-01-01

Calculations on maximum accumulation of Pu-239 and Pu-241 using MCNPX computer code with UO_2(NO_3)_2 fuel solution enriched by 19.75% operating at temperature 80°C have been conducted. AHR design was simulated with cylindrical core having diameter of 63.4 cm and 122 cm high. From this geometry we found the reactor was critical with density 108 gr U/L of UO_2(NO_3)_2 solution. The result showed that multiplication factor (k_e_f_f) of AHR was 1.05284. Then the burn up calculations were done for various time intervals from 5 days until 285 years to analyze the result. From calculation, it was found out that the saturated concentration of Pu-239 was reached after 40-50 years of operation, producing 1.23 x 102 gr and the activity 7.645 Ci. While for operate time of AHR to produce Pu-241 should under 80 years with mass 21.7 gr and the activity 2.247 x 103 Ci. The accumulations of both isotopes are considered to be small, having low potential for misusing them for producing nuclear weapon. (author)

U, Pu, and Am nuclear signatures of the Thule hydrogen bomb debris

DEFF Research Database (Denmark)

Eriksson, Mats; Lindahl, Patric; Roos, Per

2008-01-01

). In the five hot particles examined, the measured uranium atomic ratio was U-235/U-238 = 1.02 +/- 0.16 and the Pu-isotopic ratios were as follows: Pu-240/Pu-239 0.0551 +/- 0.0008 (atom ratio), Pu-238/Pu239+240 = 0.0161 +/- 0.0005 (activity ratio), Pu-241/Pu239+240 = 0.87 +/- 0.12 (activity ratio), and Am-241...... than one Pu source involved in the accident, confirming earlier studies. The Pu-238/Pu239+240 activity ratio and the Pu-240/Pu-239 atomic ratio were divided into at least two Pu-isotopic ratio groups. For both Pu-isotopic ratios, one ratio group had identical ratios as the five hot particles described...... above and for the other groups the Pu isotopic ratios were lower (Pu-238/Pu239+240 activity ratio similar to 0.01 and the Pu-240/Pu-239 atomic ratio 0.03). On the studied particles we observed that the U/Pu ratio decreased as a function of the time these particles were present in the sediment. We...

Studies in the solubility of Pu(III) oxalate

Energy Technology Data Exchange (ETDEWEB)

Hasilkar, S P; Khedekar, N B; Chander, K; Jadhav, V; Jain, H C [Bhabha Atomic Research Centre, Bombay (India). Fuel Reprocessing Div.

1994-11-01

Studies have been carried out on the solubility of Pu(III) oxalate by precipitation of Pu(III) oxalate from varying concentrations of HNO[sub 3]/HCl (0.5-2.0M) solutions and also by equilibrating freshly prepared Pu(III) oxalate with solutions containing varying concentrations of HNO[sub 3]/HCl, oxalic acid and ascorbic acid. Pu(III) solutions in HNO[sub 3] and HCl media were prepared by reduction of Pu(IV) with ascorbic acid. 0.01-0.10M ascorbic acid concentration in the aqueous solution was maintained as holding reductant. The solubility of Pu(III) oxalate was found to be a minimum in 0.5M-1M HNO[sub 3]/HCl solutions containing 0.05M ascorbic acid and 0.2M excess oxalic acid in the supernatant. (author) 6 refs.; 6 tabs.

Assembly-level analysis of heterogeneous Th–Pu PWR fuel

International Nuclear Information System (INIS)

Zainuddin, Nurjuanis Zara; Parks, Geoffrey T.; Shwageraus, Eugene

2017-01-01

Highlights: • We directly compare homogeneous and heterogeneous Th–Pu fuel. • Examine whether there is an increase in Pu incineration in the latter. • Homogeneous fuel was able to achieve much higher Pu incineration. • In the heterogeneous case, U-233 breeding is faster (larger power fraction), thus decreasing incineration of Pu. - Abstract: This study compares homogeneous and heterogeneous thorium–plutonium (Th–Pu) fuel assemblies (with high Pu content – 20 wt%), and examines whether there is an increase in Pu incineration in the latter. A seed-blanket configuration based on the Radkowsky thorium reactor concept is used for the heterogeneous assembly. This separates the thorium blanket from the uranium seed, or in this case a plutonium seed. The seed supplies neutrons to the subcritical thorium blanket which encourages the in situ breeding and burning of "2"3"3U, allowing the fuel to stay critical for longer, extending burnup of the fuel. While past work on Th–Pu seed-blanket units shows superior Pu incineration compared to conventional U–Pu mixed oxide fuel, there is no literature to date that directly compares the performance of homogeneous and heterogeneous Th–Pu assembly configurations. Use of exactly the same fuel loading for both configurations allows the effects of spatial separation to be fully understood. It was found that the homogeneous fuel with and without burnable poisons was able to achieve much higher Pu incinerations than the heterogeneous fuel configurations, while still attaining a reasonably high discharge burnup. This is because in the heterogeneous cases, "2"3"3U breeding is faster, thereby contributing to a much larger fraction of total power produced by the assembly. In contrast, "2"3"3U build-up is slower in the homogeneous case and therefore Pu burning is greater. This "2"3"3U begins to contribute a significant fraction of power produced only towards the end of life, thus extending criticality, allowing more Pu to

Studies of PVC/ENR blends: blend compositions

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

2002-01-01

Blends of poly(vinyl chloride/epoxidized natural rubber (PVC/ENR) were prepared by using Bra bender Plasticorder at compositions ranging from 0-100% PVC. They were blended at 150 degree C mixing temperature, 50 rpm rotor speed and 10 minutes mixing time. The blends were characterized for tensile strength , elongation at break, glass transition temperatures and Fourier transform infra red spectroscopy (FTIR). Results revealed that as the PVC content increases the blend behaviour changes from elastomeric to glassy. However the blends found to be compatible at all compositions. (Author)

A COMPARISON OF (PuU)C AND (PuU)O$sub 2$ FUELED FAST BREEDER REACTORS

Energy Technology Data Exchange (ETDEWEB)

Kazi, A. Halim; Rosen, Stanley

1963-11-15

BS>A conceptual evaluation is presented of a (PuU)C 500Mw(e) reactor which uses a moderate power generation of 40 kw/ft and a maximum fuel temperature of 2900 deg F, well below the 4500 deg F melting point of Pu/sub 0.2/U/sub 0.8/C. The principal design characteristics and fuel cycle costs are tabulated together with those of a (PuU)O/sub 2/ design of equal power. The comparison shows that the carbide core has significant economic and safety advantages over the oxide core. (D.L.C.)

Contribution to the study of the upper valence states of Pu

International Nuclear Information System (INIS)

Musante, Yves.

1975-01-01

The properties of the Pu(VI) and Pu(VII) ions in aqueous solutions were investigated: spectrophotometric study of the formation of PuO 2 2+ complexes with hydroxyl ions; electrochemical study of PuO 2 2+ ; preparation, determination and coprecipitation of Pu(VII); electrochemical study of Pu(VII). A preliminary research was made on the chemistry of Pu in non-aqueous solutions especially the dissolution and the determination of Pu in propylene carbonate [fr

Unsafe Coulomb excitation of 240-244Pu

International Nuclear Information System (INIS)

Ahmad, I.; Amro, H.; Carpenter, M. P.; Chowdhury, P.; Cizewski, J.; Cline, D.; Greene, J. P.; Hackman, G.; Janssens, R. V. F.; Khoo, T. L.; Lauritsen, T.; Lister, C. J.; Macchiavelli, A. O.; Nisius, D. T.; Reiter, P.; Seabury, E. H.; Seweryniak, D.; Siem, S.; Uusitalo, J.; Wiedenhoever, I.; Wu, C. Y.

1999-01-01

The high spin states of 240 Pu and 244 Pu have been investigated with GAMMASPHERE at ATLAS, using Coulomb excitation with a 208 Pb beam at energies above the Coulomb barrier. Data on a transfer channel leading to 242 Pu were obtained as well. In the case of 244 Pu, the yrast band was extended to 34h b ar revealing the completed πi 13/2 alignment, a ''first'' for actinide nuclei. The yrast sequence of 242 Pu was also extended to higher spin and a similar backbend was delineated. In contrast, while the ground state band of 240 Pu was measured up to the highest rotational frequencies ever reported in the actinide region (approximately300 keV), no sign of particle alignment was observed. In this case, several observable such as the large B(E1)/B(E2) branching ratios in the negative parity band, and the vanishing energy staggering between the negative and positive parity bands suggest that the strength of octupole correlations increases with rotational frequency. These stronger correlations may well be responsible for delaying or suppressing the πi 13/2 particle alignment

Plutonium activities and 240Pu/ 239Pu atom ratios in sediment cores from the east China sea and Okinawa Trough: Sources and inventories

Science.gov (United States)

Wang, Zhong-liang; Yamada, Masatoshi

2005-05-01

Plutonium concentrations and 240Pu/ 239Pu atom ratios in the East China Sea and Okinawa Trough sediment cores were determined by isotope dilution inductively coupled plasma mass spectrometry after separation using ion-exchange chromatography. The results showed that 240Pu/ 239Pu atom ratios in the East China Sea and Okinawa Trough sediments, ranging from 0.21 to 0.33, were much higher than the reported value of global fallout (0.18). The highest 240Pu/ 239Pu ratios (0.32-0.33) were observed in the deepest Okinawa Trough sediment samples. These ratios suggested the US nuclear weapons tests in the early 1950s at the Pacific Proving Grounds in the Marshall Islands were a major source of plutonium in the East China Sea and Okinawa Trough sediments, in addition to the global fallout source. It was proposed that close-in fallout plutonium was delivered from the Pacific Proving Grounds test sites via early direct tropospheric fallout and transportation by the North Pacific Equatorial Circulation system and Kuroshio Current into the Okinawa Trough and East China Sea. The total 239 + 240 Pu inventories in the cores were about 150-200% of that expected from direct global fallout; about 46-67% of the total inventories were delivered from the Pacific Proving Grounds. Much higher 239 + 240 Pu inventories were observed in the East China Sea sediments than in sediments of the Okinawa Trough, because in the open oceans, part of the 239 + 240 Pu was still retained in the water column, and continued Pu scavenging was higher over the margin than the trough. According to the vertical distributions of 239 + 240 Pu activities and 240Pu/ 239Pu atom ratios in these cores, it was concluded that sediment mixing was the dominant process in controlling profiles of plutonium in this area. Faster mixing in the coastal samples has homogenized the entire 240Pu/ 239Pu ratio record today; slightly slower mixing and less scavenging in the Okinawa Trough have left the surface sediment ratios closer

Determination of plutonium isotopes (²³⁸Pu, ²³⁹Pu, ²⁴⁰Pu, ²⁴¹Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements

DEFF Research Database (Denmark)

Xu, Yihong; Qiao, Jixin; Hou, Xiaolin

2014-01-01

counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5×105 for 20 g soil compared to the level reported in the literature......, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference......Pu. However, it is impossible to measure 238Pu using ICP-MS in environmental samples even a decontamination factor as high as 106 for uranium was obtained by chemical separation....

Estimation of Ni63, Pu241, Pu242 and Am243 from Co60, Pu239, and Cm244 activities in groundwater samples

International Nuclear Information System (INIS)

Holcomb, H.P.

1993-01-01

The Part B Permit for F ampersand H Seepage Basins calls for analysis of several constituents of concern in groundwater monitoring wells. Four of these analytes are the radionuclides Ni 63 , Pu 241 , Pu 242 , and Am 243 . These are currently not being analyzed due to their very difficult, tedious analytical schemes coupled with their relatively low activity values. This report demonstrates how the activity value for Ni 63 , a week beta emitter, can be estimated from that of Co 60 , an easily detectable, high-energy gamma emitter. Similarly, estimates of Pu 241 , a beta emitter, and the alpha-emitting Pu 242 can be made from the activity value of the more easily detected Pu 239 . Am 243 can be estimated from the activity of Cm 244 , which is easier to detect because of a shorter half-life (higher specific activity) and the emission of higher energy alpha particles. These correlations are made under very specific parameters in order to ensure the validity of this approach. Therefore, assumptions must be established setting ground rules for establishing these activity relationships. Bases for these assumptions are explained and/or referenced. Their degree of uncertainty limits the accuracy of the data so that the term ''estimate'' is used. Such soundly-based, conservative estimates for these four rads can provide a tool for evaluating any hazards from their presence over the next several years. Hopefully, during this time, sufficient advances will be made in their radiochemical analyses and in counting techniques so that in the future, their activities may be quantitatively determined more easily and also more cost effectively

Ceramic grade (U,Pu)O2 powder fabrication

International Nuclear Information System (INIS)

Cristallini, O.A.; Villegas de Maroto, Marina; De Pino, J.I.; Osuna, H.A.

1980-01-01

Ceramic grade UO 2 powder was obtained by the homogeneous precipitation method. This procedure was afterwards applied to the fabrication of ceramic grade (U,Pu)O 2 powders, and mixed oxide powders with Pu content ranging from 0.7 to 16% were obtained. The obtainment of mixed ceramic oxides as well as the recuperation of fabrication scraps were developed in three steps: 1)study of the process of homogeneous precipitation of ammonium diuranate (ADU); 2) co-precipitation of ADU/PuO 2 .H 2 O for Pu concentrations of 0.6 and 6.8; 3) the thermal conditioning to mixed oxide (U,Pu)O 2 powders. The experimental procedure involves the following steps: preparation of the PuO 2 (NO 3 ) 4 solution; co-precipitation of the PuO 2 (NO 3 ) 2 solution with an UO 2 (NO 3 ) 2 solution; filtration and drying of the precipitate, thermal treatment and finally, mixing, pressing and sintering of the (U,Pu)O 2 and Nukem UO 2 powder with a 0. of zinc stearate. Different controls were made by means of physical, chemical and ceramographic tests. This method can be used for the fabrication of fast reactor fuels or, previous mechanical dispersion in UO 2 powder, for the fabrication of thermal reactors fuels. (M.E.L.) [es

Agave nonwovens in polypropylene composites: mechanical and thermal studies

CSIR Research Space (South Africa)

John, MJ

2015-03-01

Full Text Available Blends of agave fibres with wool waste, pineapple leaf fibres and polypropylene fibres were manufactured by needle-punching technique. Composites were prepared with polypropylene matrix by the process of compression moulding. The effects of blend...

Study of U - Pu - Fe alloys (Masurca critical experiment)

International Nuclear Information System (INIS)

Barthelemy, P.; Boucher, R.

1965-01-01

Three compositions have been studied: 73.5 U - 25 Pu - 1.5 Fe (weight %) 74 U - 25 Pu - 1 Fe 74.5 U - 25 Pu - 0.5 Fe Elaboration and Casting are easy. After two weeks in air 74.5 U - 25 Pu - 0.5 Fe alloys are reduced in powder. As-cast alloys containing 1 and 1,5% Fe are kept undamaged during several months. A rapid oxidisation of the alloys is however observed when the samples undergo the phase transformation (at 595 deg. C and 590 deg. C respectively). Ignition tests in the presence of air show that the oxidisation starts at about 250 deg. C and that the reaction does not spread. Ignition is not observed during heating from 20 to 660 deg. C. The transformation temperature, the melting temperature and the thermal expansion coefficients have been determined by dilatometry. Below the transformation temperature, the principal phases are U-Pu zeta and (U, Pu) 6 Fe. Thermal conductibility, Young modulus, density and heat of fusion have been measured. Compatibility tests show that between U-Pu-Fe and stainless steel a phase of (U, Pu) 6 Fe type is formed. The 74 U - 25 Pu - 1% Fe alloy seems to behave better than 73.5 U - 25 Pu - 1.5% Fe alloy because the (U, Pu) 6 Fe layer is two or three times smaller. Finally, the thermal stability has been studied with the 74 U - 25 Pu - 1% Fe alloy. A dilatometric anomaly (very weak expansion) occurs when the sample is heated above transformation temperature and cooled. But there is no anomaly by thermal cycling from 50 deg. C to 400 deg. C and there is no deterioration of alloys by heat treatments at 100 deg. C, 200 deg. C, 300 deg. C during 5 months under vacuum. (authors) [fr

Np Analysis in IAT-Samples Containing <10 Microgram Pu

International Nuclear Information System (INIS)

Ludwig, R.; Raab, W.; Dashdondog, J.; Balsley, S.

2008-01-01

A method for the determination of neptunium to plutonium in safeguards samples containing less than 10 microgram Pu is presented. The chemical treatment and the optimized measurement conditions for gamma spectrometry are reported. This method is based on thermal ionization mass spectrometry (TIMS) after chemical treatment and separation and was validated with mixtures of U, Pu and Np certified reference materials and using the 237 Np standard addition method, followed by separation of the waste fraction and gamma spectrometric analysis. The highest sensitivity, precision and accuracy in the determination of the Np:Pu ratio at microgram levels of Pu is achieved by evaluating 241 Pu and 233 Pa after measuring the adsorbent with a well-type gamma detector 3 weeks after chemical treatment. The repeatability of determining the Np:Pu ratio is estimated to be 5%, the maximum uncertainty as determined from comparing the 4 measurement modes is within ± 10% for samples containing 3 μg Pu, while being within ± 20% for 0.4 μg Pu. (authors)

Np Analysis in IAT-Samples Containing <10 Microgram Pu

Energy Technology Data Exchange (ETDEWEB)

Ludwig, R.; Raab, W.; Dashdondog, J.; Balsley, S. [IAEA, Safeguards Analytical Laboratory, Wagramer Str. 5, P.O. Box 100, A-1400 Vienna (Austria)

2008-07-01

A method for the determination of neptunium to plutonium in safeguards samples containing less than 10 microgram Pu is presented. The chemical treatment and the optimized measurement conditions for gamma spectrometry are reported. This method is based on thermal ionization mass spectrometry (TIMS) after chemical treatment and separation and was validated with mixtures of U, Pu and Np certified reference materials and using the {sup 237}Np standard addition method, followed by separation of the waste fraction and gamma spectrometric analysis. The highest sensitivity, precision and accuracy in the determination of the Np:Pu ratio at microgram levels of Pu is achieved by evaluating {sup 241}Pu and {sup 233}Pa after measuring the adsorbent with a well-type gamma detector 3 weeks after chemical treatment. The repeatability of determining the Np:Pu ratio is estimated to be 5%, the maximum uncertainty as determined from comparing the 4 measurement modes is within {+-} 10% for samples containing 3 {mu}g Pu, while being within {+-} 20% for 0.4 {mu}g Pu. (authors)

Evaluation of fission cross sections and covariances for {sup 233}U, {sup 235}U, {sup 238}U, {sup 239}Pu, {sup 240}Pu, and {sup 241}Pu

Energy Technology Data Exchange (ETDEWEB)

Kawano, Toshihiko [Kyushu Univ., Fukuoka (Japan); Matsunobu, Hiroyuki [Data Engineering, Inc. (Japan); Murata, Toru [AITEL Corporation, Tokyo (JP)] [and others

2000-02-01

A simultaneous evaluation code SOK (Simultaneous evaluation on KALMAN) has been developed, which is a least-squares fitting program to absolute and relative measurements. The SOK code was employed to evaluate the fission cross sections of {sup 233}U, {sup 235}U, {sup 238}U, {sup 239}Pu, {sup 240}Pu, and {sup 241}Pu for the evaluated nuclear data library JENDL-3.3. Procedures of the simultaneous evaluation and the experimental database of the fission cross sections are described. The fission cross sections obtained were compared with evaluated values given in JENDL-3.2 and ENDF/B-VI. (author)

Quantitative dissolution of (U, Pu)O2 MOX (0.4% to 44% PuO2) using microwave heating technique

International Nuclear Information System (INIS)

Malav, R.K.; Fulzele, Ajit K.; Prakash, Amrit; Afzal, Md.; Panakkal, J.P.

2011-01-01

AFFF has fabricated the (U, Pu)O 2 mixed oxide fuels for PHWRs, BWRs, PFBRs and FBTRs. The quantitative dissolution of the fuel samples are required within time for accurate determination of uranium-plutonium in chemical quality control laboratory. This paper describes the use of microwave heating technique in quantitative dissolution of (U, Pu)O 2 MOX (from 0.4% to 44% PuO 2 ). (author)

A study of accelerated radiation damage effects in PuO{sub 2} and gadolinia-stabilized cubic zirconia, Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93}, doped with {sup 238}Pu

Energy Technology Data Exchange (ETDEWEB)

Burakov, B.E., E-mail: burakov@peterlink.ru [V.G. Khlopin Radium Institute, 28, 2-nd Murinskiy Ave., St. Petersburg, 194021 (Russian Federation); Yagovkina, M.A. [A.F. Ioffe Physical-Technical Institute, 26, Politekhnicheskaya, St. Petersburg, 194021 (Russian Federation)

2015-12-15

Polycrystalline samples of cubic zirconia, Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93}, doped with approximately 9.9 wt.% {sup 238}Pu, and PuO{sub 2} containing 11.0 wt. % {sup 238}Pu (and main isotope is {sup 239}Pu) have been repeatedly studied during many years by X-ray diffraction analysis. At a temperature of 25 °C the unit-cell parameter of PuO{sub 2} increases depending on accumulated dose, and is accompanied by decrease of coherent scattering region (CSR). Self-irradiation of Zr{sub 0.79}Gd{sub 0.14}Pu{sub 0.07}O{sub 1.93} is accompanied with repeated change of unit-cell parameter and CSR.

Effect of equilibration time on Pu desorption from goethite

International Nuclear Information System (INIS)

Wong, Jennifer C.; Powell, Brian A.; Zavarin, Mavrik; Begg, James D.; Kersting, Annie B.

2015-01-01

It has been suggested that strongly sorbing ions such as plutonium may become irreversibly bound to mineral surfaces over time which has implications for near- and far-field transport of Pu. Batch adsorption-desorption data were collected as a function of time and pH to study the surface stability of Pu on goethite. Pu(IV) was adsorbed to goethite over the pH range 4.2 to 6.6 for different periods of time (1, 6, 15, 34 and 116 d). Following adsorption, Pu was leached from the mineral surface with desferrioxamine B (DFOB), a complexant capable of effectively competing with the goethite surface for Pu. The amount of Pu desorbed from the goethite was found to vary as a function of the adsorption equilibration time, with less Pu removed from the goethite following longer adsorption periods. This effect was most pronounced at low pH. Logarithmic desorption distribution ratios for each adsorption equilibration time were fit to a pH-dependent model. Model slopes decreased between 1 and 116 d adsorption time, indicating that overall Pu(IV) surface stability on goethite surfaces becomes less dependent on pH with greater adsorption equilibration time. The combination of adsorption and desorption kinetic data suggest that non-redox aging processes affect Pu sorption behavior on goethite.

Analysis and composition of the first U-Pu charge (0,043 per cent of Pu); Analyse et constitution du 1. jeu U-Pu (0,043 pour cent de Pu)

Energy Technology Data Exchange (ETDEWEB)

Brunet, J P; Lapparent, D de; Lourme, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-07-01

Checking the homogeneity in the content of plutonium of 0,043 per cent Pu-natural uranium alloy slugs has been made by Pu 240 and U 238 spontaneous fissions neutrons counting. The purpose of the test was to select groups of slugs to be correctly associated into fuel rods for critical experiments. General technic for spontaneous fissions counting, then elaboration of data in view of ranking the slugs are described. Results are given for this particular case. (authors) [French] On a effectue un controle d'homogeneite de teneur en plutonium sur des billettes d'alliage 0,043 pour cent Pu-uranium naturel, par comptage des fissions spontanees du plutonium 240 et de l'uranium 238. Le but du controle etait de permettre une association correcte de ces billettes a l'interieur des elements combustibles destines a servir dans des experiences critiques. On indique la methode generale de comptage des fissions spontanees, puis le depouillement des donnees en vue du classement des barreaux. Les resultats pour ce cas particulier sont donnes dans le rapport. (auteurs)

242Pu: Preliminary evaluation with consideration of 240Pu, and some sensitivity results

International Nuclear Information System (INIS)

Jary, J.; Lagrange, C.; Philis, C.

1978-01-01

A preliminary evaluation of 242 Pu nuclear data is presented for the neutron energy range from 10 keV to 20 MeV. The fission cross section is based upon recent experimental measurements on 242 Pu. The remaining cross sections have been calculated using various nuclear models with parameters obtained mainly by both fits on 240 Pu experimental data and general reflexions on the actinides. Particular care has been taken of the direct interactions. The laws of secondary neutron energy spectra and the average number of neutrons produced per fission have been evaluated. The results have been placed in ENDF/BIV format and combined with the low energy region of ENDF/BIV MAT = 1161 data to make complete the evaluation over the whole energy range 10 -5 eV - 20 MeV. Finally, the sensitivities of some of these nuclear data available for reactor calculations are given in terms of the variation of the calculated critical masses

Measurement of oxygen chemical diffusion in PuO{sub 2-x} and analysis of oxygen diffusion in PuO{sub 2-x} and (Pu,U)O{sub 2-x}

Energy Technology Data Exchange (ETDEWEB)

Kato, Masato; Uchida, Teppei [Advanced Nuclear System Research and Development Directorate, Japan Atomic Energy Agency, 4-33 Muramatsu, Tokai-mura, Ibaraki 319-1194 (Japan); Sunaoshi, Takeo [Inspection Development Company Ltd., 4-33 Muramatsu, Tokai-mura, Ibaraki 319-1194 (Japan)

2013-02-15

Oxygen chemical diffusion in PuO{sub 2-x} was investigated in the temperature range of 1473-1873 K by thermogravimetry as functions of oxygen-to-metal (O/M) ratios and temperatures. The oxygen chemical diffusion coefficients, D were determined assuming that the reduction curves were dominated by a diffusion process. The O/M ratio and Pu content dependence on the chemical diffusion coefficients were evaluated. The chemical diffusion coefficient had its minimum value at around O/M=1.98 and decreased with increasing Pu content in (U,Pu)O{sub 2-x}. The self-diffusion coefficients were evaluated. A model for describing the relationship among O/M ratio, oxygen chemical diffusion, and self-diffusion was proposed based on defect chemistry. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The Transport of Close-In Fallout Plutonium in the Northwest Pacific Ocean: Tracing the Water Mass Movement Using {sup 240}Pu/{sup 239}Pu Atom Ratio

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang-Han [Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of); Hong, Gi-Hoon; Suk, Moon-Sik [Korea Ocean Research and Development Institute, Seoul (Korea, Republic of); Gastaud, J. [International Atomic Energy Agency, Marine Environment Laboratory (Monaco); La Rosa, J. [National Institute of Standards and Technology, Ionizing Radiation Division, Gaithersburg, Maryland (United States); Kim, Chul-Soo [Environmental Laboratories, International Atomic Energy Agency, Seibersdorf (Austria); Wyse, E. [New Brunswick Laboratory Argonne, IL (United States); Povinec, P. P. [Comenius University, Faculty of Mathematics and Physics, Bratislava (Slovakia)

2013-07-15

{sup 240}Pu/{sup 239}Pu atom ratios in seawater and surface sediment collected from the northwest (NW) Pacific Ocean from 1992 to 1997 were determined using ICP-sector field mass spectrometry (ICP-MS). In whole water columns, the atom ratios of {sup 240}Pu/{sup 239}Pu were higher than the global fallout ratio (0.18). It is noted that the atom ratios of {sup 240}Pu/2{sup 39}Pu in the seawater increase with depth. Such elevated {sup 240}Pu/{sup 239}Pu atom ratios indicate that the close-in fallout plutonium isotopes originating from the Pacific Proving Grounds (PPGs) due to the U.S. tests are prevailing in the seawater in the NW Pacific Ocean. However, the {sup 240}Pu/{sup 239}Pu atom ratios in the surface sediment from the NW Pacific Ocean varied with the sampling locations. As a consequence, this study will provide the information that the water mass along with the current plays a key role in driving the distribution of Pu and in transporting Pu from the PPGs to the far eastern marginal sea in the NW Pacific Ocean. (author)

Thermodynamic evaluation of liquid Cd cathode containing U and Pu

International Nuclear Information System (INIS)

Kurata, Masaki; Uozumi, Koichi; Kato, Tetsuya; Iizuka, Masatoshi

2009-01-01

In our previous study, a mixture of U and Pu was recovered in liquid Cd cathode from molten salt under various conditions of the U:Pu ratio. Two important things were observed. The first was that three kinds of precipitated phase had been detected in the saturated liquid Cd cathode, such as a U metal and two kinds of U-Pu-Cd compound. The compositions of the compounds were roughly (U+Pu):Cd=1:11 and (U+Pu):Cd=1:6. The second was that the U metal had selectively precipitated in the saturated liquid Cd cathode under the condition that the U:Pu ratio is higher than about 0.8 in the liquid Cd phase. In the present study, phase diagrams were evaluated by the CALPHAD method on the liquid Cd cathode containing U and Pu. The U-Pu-Cd compounds were modeled as MCd 11 -type and MCd 6 -type, respectively, based on the reported binary phase diagrams of U-Cd and Pu-Cd. The calculated result reasonably agreed with the experimental observations. The variations in the U and Pu activities were estimated along with the U:Pu ratio, which is related to the precipitation of various phases in the liquid Cd cathode. (author)

Radiation induced emulsion graft polymerization of 4-vinylpyridine onto PE/PP nonwoven fabric for As(V) adsorption

Science.gov (United States)

Akkaş Kavaklı, Pınar; Kavaklı, Cengiz; Seko, Noriaki; Tamada, Masao; Güven, Olgun

2016-10-01

A novel nonwoven fabric adsorbent having 4-vinylpyridine functional groups was prepared by using radiation-induced emulsion graft polymerization method and grafting 4-vinylpyridine monomer onto a polyethylene-coated polypropylene nonwoven fabric (NWF) in aqueous emulsion solution. The grafting conditions of the 4-vinylpyridine monomer onto the NWF were optimised and 150% Dg VP-g-NWF was prepared using 30 kGy pre-irradiation dose, 5% VP monomer concentration and 0.5% (w/w) Tween 20 in aqueous emulsion. Grafted 4-vinylpyridine chains on the NWF were then quaternized for the preparation of QVP-g-NWF adsorbent. All fabric structures were characterized by using Fourier-transform infrared spectrometer, x-ray photoelectron spectrometer and scanning electron microscope. QVP-g-NWF adsorbent was used in batch adsorption experiments for As(V) ions by studying the pH, contact time, and initial As(V) ion concentration parameters. Results showed that QVP-g-NWF adsorbent has significant As(V) adsorption and experimental As(V) adsorption capacity was 98.04 mg As(V)/g polymer from 500 mg/L initial As(V) concentration at pH 7.00.

Roles of PU.1 in monocyte- and mast cell-specific gene regulation: PU.1 transactivates CIITA pIV in cooperation with IFN-gamma.

Science.gov (United States)

Ito, Tomonobu; Nishiyama, Chiharu; Nakano, Nobuhiro; Nishiyama, Makoto; Usui, Yoshihiko; Takeda, Kazuyoshi; Kanada, Shunsuke; Fukuyama, Kanako; Akiba, Hisaya; Tokura, Tomoko; Hara, Mutsuko; Tsuboi, Ryoji; Ogawa, Hideoki; Okumura, Ko

2009-07-01

Over-expression of PU.1, a myeloid- and lymphoid-specific transcription factor belonging to the Ets family, induces monocyte-specific gene expression in mast cells. However, the effects of PU.1 on each target gene and the involvement of cytokine signaling in PU.1-mediated gene expression are largely unknown. In the present study, PU.1 was over-expressed in two different types of bone marrow-derived cultured mast cells (BMMCs): BMMCs cultured with IL-3 plus stem cell factor (SCF) and BMMCs cultured with pokeweed mitogen-stimulated spleen-conditioned medium (PWM-SCM). PU.1 over-expression induced expression of MHC class II, CD11b, CD11c and F4/80 on PWM-SCM-cultured BMMCs, whereas IL-3/SCF-cultured BMMCs expressed CD11b and F4/80, but not MHC class II or CD11c. When IFN-gamma was added to the IL-3/SCF-based medium, PU.1 transfectant acquired MHC class II expression, which was abolished by antibody neutralization or in Ifngr(-/-) BMMCs, through the induction of expression of the MHC class II transactivator, CIITA. Real-time PCR detected CIITA mRNA driven by the fourth promoter, pIV, and chromatin immunoprecipitation indicated direct binding of PU.1 to pIV in PU.1-over-expressing BMMCs. PU.1-over-expressing cells showed a marked increase in IL-6 production in response to LPS stimulation in both IL-3/SCF and PWM-SCM cultures. These results suggest that PU.1 overproduction alone is sufficient for both expression of CD11b and F4/80 and for amplification of LPS-induced IL-6 production. However, IFN-gamma stimulation is essential for PU.1-mediated transactivation of CIITA pIV. Reduced expression of mast cell-related molecules and transcription factors GATA-1/2 and up-regulation of C/EBPalpha in PU.1 transfectants indicate that enforced PU.1 suppresses mast cell-specific gene expression through these transcription factors.

Structural studies of the phase separation in the UO2–PuO2–Pu2O3 ternary system

International Nuclear Information System (INIS)

Truphémus, Thibaut; Belin, Renaud C.; Richaud, Jean-Christophe; Reynaud, Muriel; Martinez, Marie-Annick; Félines, Isabelle; Arredondo, Antoine; Miard, Audrey; Dubois, Thierry; Adenot, Frédéric; Rogez, Jacques

2013-01-01

In the oxygen hypo-stoichiometric range of (U 1−y Pu y )O 2−x mixed oxide MOX fuels, the U–Pu–O phase diagram is known to exhibit a large biphasic domain depending on the Pu content. However, the phase equilibria are still to be fully described as various representations are proposed in the literature. In the present work, we notify new insights into the phase separation occurring in the UO 2 –PuO 2 –Pu 2 O 3 domain at room temperature. Our microstructural and X-ray diffraction results are compared to the different representations reported in the literature. We provide, for the first time in the hypo-stoichiometric domain, an indisputable experimental observation of a triphasic region at high Pu content, composed of two fluorite-type structures and of one α-Pu 2 O 3 sesquioxyde type structure. These results are in contradiction with previous experimental representations of the U–Pu–O ternary system.

Assessment of 238Pu and 239+240Pu, in marine sediments of the oceans Atlantic and Pacific of Guatemala

International Nuclear Information System (INIS)

Mendez Ochaita, L.

2000-01-01

In this investigation samples of marine sediments were taken from 14 places representatives of the oceans coast of Guatemala. For the assesment of 238 Pu and 239+240 Pu in sediments a radiochemical method was used to mineralize sediments and by ionic interchange it was separated from other elements, after that an electrodeposition of plutonium was made in metallic discs. The radioactivity of plutonium was measured by alpha spectrometry system and the alpha spectrums were obtained. The levels of plutonium are not higher than other countries that shown contamination. The contamination of isotope of 239+240 Pu is higher than 238 Pu and the contamination by two isotopes of plutonium is higher in the Atlantic than the Pacific ocean

Study of new U(VI) and Pu(VI) coprecipitation methods for the preparation of (U,Pu)O2

International Nuclear Information System (INIS)

Sanoit, J. de.

1990-01-01

Two U(VI) and Pu(VI) coprecipitation methods have been studied, for the definition of new processes to prepare (U,Pu)O 2 mixed oxides suitable for making MoX fuels or fast breeder reactor fuels. The first system is based on the coprecipitation of a new U(VI), Pu(VI) compound; ammonium uranoplutonate, where as a second system is related to the precipitation of uranyl plutonyl monocarbonate. Experimental conditions to optimize the precipitation and the filtration steps of these two systems have been determined. After calcination under reducing conditions, the mixed oxides obtained are characterized according to different techniques: granulometry, thermogravimetry, solubility in boiling HNO 3 solutions. The properties of such oxides are excellent. The possible processes for preparing (U, Pu)O 2 using these new routes are compared with those actually exploited [fr

Chemical speciation of Pu in natural waters

International Nuclear Information System (INIS)

Nelson, D.M.; Larsen, R.P.; Penrose, W.R.

1983-01-01

The behavior of plutonium in natural waters is determined to a major degree by the chemical forms which are present. We have characterized the ambient Pu in a number of surface waters with regard to its oxidation state and association with natural colloidal organic carbon compounds using a combination of field measurements and laboratory experiments. Both of these factors are shown to have a profound effect on the adsorption of Pu to natural sediments, since both complexation with organic matter and oxidation compete with adsorption. The concentration of organic carbon in the water is the key variable influencing both oxidation state and organic binding. The adsorption process conforms to the laws applicable to a reversible equilibrium with values of the distribution coefficient, K/sub D/, measured in laboratory experiments being similar to those observed for ambient Pu. Experiments using natural waters and sediments in which the Pu concentration was varied show the forms present at typical ambient concentrations (10 -17 - 10 -14 M) are the same as those found at concentrations up to 10 -7 M. Moreover, the affinity for sediments did not change with concentration indicating the binding sites for Pu had not become saturated. Thus, the behavior observed for Pu at ultratrace concentrations should remain unchanged throughout this concentration range. The studies in this report all deal with Pu in exchangeable (and hence source independent) forms and should therefore reflect the behavior toward which the plutonium from any source will tend with time. 13 references, 7 figures, 10 tables

Nitrate Anion Exchange in Pu-238 Aqueous Scrap Recovery Operations

International Nuclear Information System (INIS)

Pansoy-Hjelvik, M.E.; Silver, G.L.; Reimus, M.A.H.; Ramsey, K.B.

1999-01-01

Strong base, nitrate anion exchange (IX) is crucial to the purification of 238 Pu solution feedstocks with gross levels of impurities. This paper discusses the work involved in bench scale experiments to optimize the nitrate anion exchange process. In particular, results are presented of experiments conducted to (a) demonstrate that high levels of impurities can be separated from 238 Pu solutions via nitrate anion exchange and, (b) work out chemical pretreatment methodology to adjust and maintain 238 Pu in the IV oxidation state to optimize the Pu(IV)-hexanitrato anionic complex sorption to Reillex-HPQ resin. Additional experiments performed to determine the best chemical treatment methodology to enhance recovery of sorbed Pu from the resin, and VIS-NIR absorption studies to determine the steady state equilibrium of Pu(IV), Pu(III), and Pu(VI) in nitric acid are discussed

Electronic structure of α- and δ-Pu from photoelectron spectroscopy

International Nuclear Information System (INIS)

Arko, A. J.; Joyce, J. J.; Morales, L.; Wills, J.; Lashley, J.; Wastin, F.; Rebizant, J.

2000-01-01

We report photoemission results on α- and δ-Pu using a laser plasma light source (LPLS) as well as He light as the exciting radiation. The LPLS is a pseudocontinuum tunable light source with intensities rivaling some second-generation synchrotrons. Both phases of Pu display a narrow, temperature-independent, 5f-related feature at the Fermi energy, which is narrower in δ-Pu than in α-Pu, suggestive of possible heavy-fermion-like behavior. In both α-Pu and δ-Pu the photon-energy dependence of this feature suggests some 6d admixture, albeit somewhat smaller in δ-Pu. In this respect it differs qualitatively from Ce and U heavy fermions. (c) 2000 The American Physical Society

Aspects of 238Pu production in the experimental fast reactor JOYO

International Nuclear Information System (INIS)

Osaka, Masahiko; Koyama, Shin-ichi; Tanaka, Kenya; Itoh, Masahiko; Saito, Masaki

2005-01-01

Experimental determination of 238 Pu in 237 Np samples irradiated in the experimental fast reactor JOYO was done as part of the demonstration of 238 Pu production from 237 Np in fast reactors within the framework of the protected Pu production project, which aims at reinforcement of proliferation resistance of Pu by increasing the 238 Pu isotopic ratio. 238 Pu production amount in the irradiated 237 Np samples was determined by a radioanalytical technique. Aspects of 238 Pu production were examined on the basis of the present radioanalysis. The 238 Pu production amount depends on the neutron spectrum which can range from that of a typical fast reactor to a nearly epi-thermal spectrum. It is concluded that the fast reactor has not only high potential for use in protected Pu production, but also as an incinerator for excess Pu

137Cs, 239+24Pu and 24Pu/239Pu atom ratios in the surface waters of the western North Pacific Ocean, eastern Indian Ocean and their adjacent seas

International Nuclear Information System (INIS)

Yamada, Masatoshi; Zheng Jian; Wang Zhongliang

2006-01-01

Surface seawater samples were collected along the track of the R/V Hakuho-Maru cruise (KH-96-5) from Tokyo to the Southern Ocean. The 137 Cs activities were determined for the surface waters in the western North Pacific Ocean, the Sulu and Indonesian Seas, the eastern Indian Ocean, the Bay of Bengal, the Andaman Sea, and the South China Sea. The 137 Cs activities showed a wide variation with values ranging from 1.1 Bq m -3 in the Antarctic Circumpolar Region of the Southern Ocean to 3 Bq m -3 in the western North Pacific Ocean and the South China Sea. The latitudinal distributions of 137 Cs activity were not reflective of that of the integrated deposition density of atmospheric global fallout. The removal rates of 137 Cs from the surface waters were roughly estimated from the two data sets of Miyake et al. [Miyake Y, Saruhashi K, Sugimura Y, Kanazawa T, Hirose K. Contents of 137 Cs, plutonium and americium isotopes in the Southern Ocean waters. Pap Meteorol Geophys 1988;39:95-113] and this study to be 0.016 yr -1 in the Sulu and Indonesian Seas, 0.033 yr -1 in the Bay of Bengal and Andaman Sea, and 0.029 yr -1 in the South China Sea. These values were much lower than that in the coastal surface water of the western Northwest Pacific Ocean. This was likely due to less horizontal and vertical mixing of water masses and less scavenging. 239+24 Pu activities and 24 Pu/ 239 Pu atom ratios were also determined for the surface waters in the western North Pacific Ocean, the Sulu and Indonesian Seas and the South China Sea. The 24 Pu / 239 Pu atom ratios ranged from 0.199 ± 0.026 to 0.248 ± 0.027 on average, and were significantly higher than the global stratospheric fallout ratio of 0.18. The contributions of the North Pacific Proving Grounds close-in fallout Pu were estimated to be 20% for the western North Pacific Ocean, 39% for the Sulu and Indonesian Seas and 42% for the South China Sea by using the two end-member mixing model. The higher 24 Pu / 239 Pu atom ratios

Experimental Benchmarking of Pu Electronic Structure

International Nuclear Information System (INIS)

Tobin, J.G.; Moore, K.T.; Chung, B.W.; Wall, M.A.; Schwartz, A.J.; Ebbinghaus, B.B.; Butterfield, M.T.; Teslich, N.E. Jr.; Bliss, R.A.; Morton, S.A.; Yu, S.W.; Komesu, T.; Waddill, G.D.; van der Laan, G.; Kutepov, A.L.

2008-01-01

The standard method to determine the band structure of a condensed phase material is to (1) obtain a single crystal with a well defined surface and (2) map the bands with angle resolved photoelectron spectroscopy (occupied or valence bands) and inverse photoelectron spectroscopy (unoccupied or conduction bands). Unfortunately, in the case of Pu, the single crystals of Pu are either nonexistent, very small and/or having poorly defined surfaces. Furthermore, effects such as electron correlation and a large spin-orbit splitting in the 5f states have further complicated the situation. Thus, we have embarked upon the utilization of unorthodox electron spectroscopies, to circumvent the problems caused by the absence of large single crystals of Pu with well-defined surfaces. Our approach includes the techniques of resonant photoelectron spectroscopy, x-ray absorption spectroscopy, electron energy loss spectroscopy, Fano Effect measurements, and Bremstrahlung Isochromat Spectroscopy, including the utilization of micro-focused beams to probe single-crystallite regions of polycrystalline Pu samples.

Transuranic concentrations in reef and pelagic fish from the Marshall Islands. [/sup 239/Pu, /sup 240/Pu

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V.E.; Eagle, R.J.; Wong, K.M.; Jokela, T.A.

1980-09-01

Concentrations of /sup 239 + 240/Pu are reported in tissues of several species of reef and pelagic fish caught at 14 different atolls in the northern Marshall Islands. Several regularities that are species dependent are evident in the distribution of /sup 239 + 240/Pu among different body tissues. Concentrations in liver always exceeded those in bone and concentrations were lowest in the muscle of all fish analyzed. A progressive discrimination against /sup 239 + 240/Pu was observed at successive trophic levels at all atolls except Bikini and Enewetak, where it was difficult to conclude if any real difference exists between the average concentration factor for /sup 239 + 240/Pu among all fish, which include bottom feeding and grazing herbivores, bottom feeding carnivores, and pelagic carnivores from different atoll locations. The average concentration of /sup 239 + 240/Pu in the muscle of surgeonfish from Bikini and Enewetak was not significantly different from the average concentrations determined in these fish at the other, lesser contaminated atolls. Concentrations among all 3rd, 4th, and 5th trophic level species are highest at Bikini where higher environmental concentrations are found. The reasons for the anomalously low concentrations in herbivores from Bikini and Enewetak are not known.

Safe and Effective Ag Nanoparticles Immobilized Antimicrobial NanoNonwovens

DEFF Research Database (Denmark)

Song, Jie; Chen, Menglin; Regina, Viduthalai R.

2012-01-01

and possibility of introduction of secondary pollution. Here, we present a novel strategy to produce a safe and effective antimicrobial nanononwoven material by immobilizing AgNPs on a rigid polymer nanofibrous matrix through simple co-electrospinning of pre-prepaired AgNPs and polystyrene (PS). Distribution...... of the AgNPs on the surface of PS fibers was achieved by tuning fiber diameters during electrospinning. Atomic force microscopy (AFM) analysis revealed that the AgNPs distributed at the fiber surface were still covered by a layer of polymer, which inhibited their antimicrobial activity. UV/ozone treatment...... was thus employed to degrade the polymer coating without loosening the AgNPs, resulting in an active antimicrobial nonwoven against Gram-positive Staphylococcus xylosus. The mechanism based on cellular uptake of silver ions via close contact to the surface of AgNPs is proposed. The novel nanononwoven...

ZZ WPPR-FR-MOX/BNCMK, Benchmark on Pu Burner Fast Reactor

International Nuclear Information System (INIS)

Garnier, J.C.; Ikegami, T.

1993-01-01

Description of program or function: In order to intercompare the characteristics of the different reactors considered for Pu recycling, in terms of neutron economy, minor actinide production, uranium content versus Pu burning, the NSC Working Party on Physics of Plutonium Recycling (WPPR) is setting up several benchmark studies. They cover in particular the case of the evolution of the Pu quality and Pu fissile content for Pu recycling in PWRs; the void coefficient in PWRs partly fuelled with MOX versus Pu content; the physics characteristics of non-standard fast reactors with breeding ratios around 0.5. The following benchmarks are considered here: - Fast reactors: Pu Burner MOX fuel, Pu Burner metal fuel; - PWRs: MOX recycling (bad quality Pu), Multiple MOX recycling

Mathematical modeling of radiation-chemical processes in HNO3 solutions of Pu. 5. Effect of [HNO3] on rate constants of radiation-chemical and chemical reactions of Pu ions

International Nuclear Information System (INIS)

Vladimirova, M.V.

1993-01-01

Dependences of rate constants on [HNO 3 ] are obtained for the reactions Pu(IV) + OH, Pu(IV) + NO 3 , Pu(V) + NO 2 , Pu(III) + NO 2 , Pu(V) + Pu(III), Pu(IV) + Pu(IV), and Pu(V) + Pu(V). These dependences are obtained for [HNO 3 ] = 0.3-6 M using existing experimental and literature data and the data obtained using mathematical modeling. The correctness of the resulting dependences is checked by comparing the calculated and experimental kinetic laws for the behavior of Pu in 0.3, 0.4, 0.6, and 1.6 M HNO 3 . 17 refs., 15 figs., 2 tabs

Sorption of Pu onto some kinds of clay

International Nuclear Information System (INIS)

Jia Haihong; Si Gaohua; Liu Wei; Yu Jing

2010-01-01

There are rich clay mines holding in one area, so it's necessary to know about these clays' sorption capacity to Pu, for building radioactive waste repository in the area. Distribution coefficients of Pu onto different clays were acquired in static method, with the result about 104. The size of clay is different, but the result of Kds is near. In addition, it's estimated how far Pu moves in the most rapid speed in the clay based on these Kids', disregarding the influence of Pu-colloid. In a word, as a kind of backfilling material clays in the area can effectively prevent Pu from moving to environment, and when designing the backfilling layer, it's not necessary to catch clays through NO.200 sieve, if only considering the influence of Kd. (authors)

239Pu standards for quantitative neutron-induced autoradiography

International Nuclear Information System (INIS)

Smith, J.M.; Atherton, D.R.; Wronski, T.J.; Jee, W.S.S.

1977-01-01

The present study deals with the preparation of 239 Pu standards for neutron bone tissue autoradiography and the calibration of these standards with respect to uranium reference standards. Known concentrations of 239 Pu were prepared in methyl methacrylate and Bioplastic casting resin bars. Wafers sawed from these bars served as standards. Solid state nuclear tract detectors (Lexan polycarbonate) were used to record fission fragment tracks after the standards were exposed to a thermal neutron flux. The original bars were found to contain a uniform distribution of 239 Pu. To confirm the concentration of 239 Pu in the wafers, the induced track density from the 239 Pu standards was compared with that from uranium reference standards. The average fission fragment detection efficiency for all of the standards was 0.51

Adsorption of Pu(IV) Polymer onto 304L Stainless Steel

International Nuclear Information System (INIS)

Bronikowski, M.G.

1999-01-01

'The report, Technical Basis for Safe Operations with Pu-239 Polymer in NMS and S Operating Facilities (F and H Areas), (WSRC-TR-99-00008) was issued in an effort to upgrade the Authorization Basis (AB) for H Area facilities relative to nuclear criticality. At the time, insufficient data were found in the literature to quantify the adsorption of Pu polymer onto the surfaces of stainless steel tanks. Additional experimental or literature information on the adsorption of Pu(IV) polymer and its removal was deemed necessary to support the H Area AB. The results obtained are also applicable to processing in F Area facilities.Additional literature sources suggest that adsorption on the tank walls should not be a safety concern. The sources show that the amount of Pu polymer that adsorbs from a solution comes to a limiting amount in 5 to 7 days after which no additional Pu is adsorbed. Adsorption increases with Pu concentration and decreases with acid concentration. The adsorbed amounts are small varying from 0.5 mg/cm2 for a 0.5 g/l Pu / 0.5M HNO3 solution to 11 mg/cm2 for a 1-3 g/l Pu / 0.1M HNO3 solution. Additionally, acid concentrations greater than 0.1M will remove a percentage of adsorbed Pu.The experimental results have generally confirmed much of what has been reported in the literature. Specifically, adsorption onto stainless steel was found to increase with increased Pu concentration, and decreased acid concentration. The amount adsorbed was found to come to a limiting amount after 5 to 7 days. Pu adsorbed as polymer was found to be harder to remove than if it was adsorbed as Pu(IV). The amount of Pu adsorbed as polymer was found to be almost an order of magnitude more than that from a similar concentration Pu(IV) solution. Unlike the literature, only a slight increase in adsorption values was found when the steel surface was removed, dried, and replaced in the Pu solution. The amount of Pu as polymer which would adsorb onto the surface of a 14,000L tank was

Simulation of 239Pu location in trabecular bone: a computerized model of adult endosteal bone remodeling and its interaction with injected 239Pu

International Nuclear Information System (INIS)

Kimmel, D.B.; Jee, W.S.S.

1979-01-01

A computer simulation of the relationship of bone microanatomic metabolic activity to the microscopic location of 239 Pu in bone has been attempted. The model incorporates the rate of bone turnover, cell location and density, bone resorptive activity (as it removes 239 Pu from bone), bone formation activity (as it buries 239 Pu in bone), recycling of 239 Pu, and liver translocation of 239 Pu to bone, such that the skeletal retention curve for 239 Pu injected in monomeric form into the young adult beagle is matched. The eventual aim of this work is to calculate the radiation dose to bone cells, knowing the relative location of 239 Pu deposited in bone and the cells that reside at bone surfaces as it changes throughout the lifespan of an animal. Early results indicate that osteosarcoma incidence may be proportional to the number of alpha hits which occur to osteoprogenitor cells and osteoblasts, the dividing cell population found near surfaces where bone turnover is in progress

Blend or not to blend: a study investigating faculty members perceptions of blended teaching

Directory of Open Access Journals (Sweden)

Mehmet A Ocak

2010-12-01

Full Text Available This study examined faculty members’ perceptions of blended teaching from several perspectives. A total of 73 faculty members in Turkish Higher Education context participated in the study by completing an online survey that combined quantitative and qualitative approaches. Based on a data analysis, the faculty members’ perceptions were sorted into six categories: (a satisfaction with blended teaching, (b perceived impact on the role of the faculty, (c perceived impact on student learning, (d perceived impact on student motivation, (e advantages of blended teaching, and (f disadvantages of blended teaching. Findings indicated that faculty members were likely to agree that blended teaching provides a high degree of satisfaction and that it requires more time and commitment from the faculty. The faculty members perceived that blended teaching improves student learning and, to some extent, improves motivation. The faculty members also emphasized the importance of institutional support and the use of technology to mitigate student problems. This study presents these faculty members’ perceptions, which are helpful for those planning to implement a blended teaching approach, and makes suggestions for trouble-shooting and taking advantage of the opportunities in a blended environment successfully.

Advanced soft coverpad made of non-woven fabric; Soft fushokufu coverpad no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hayakawa, t; Kamezaki, K; Tokita, T [Takashimaya Nippatsu Kogyo, Aichi (Japan); Yamada, Y; Ono, H; Araki, O [Toyota Motor Corp., Aichi (Japan)

1997-10-01

At the present expected to enhance the product-value of automobile, it can be considered that advancement of touching and fitting feeling of seat would be important factors. For the purpose of materializing of these factors, We have noted softening of seat cover and carried out development of cover pad made of non-woven fablic. As a result of pursuing compatibility of soft feeling and durability of the cover pad, we could achieve to ensure the quality required for the material as the seat cover pad. 3 refs., 15 figs., 4 tabs.

Transfer of 239Pu to mouse fetoplacental tissues

International Nuclear Information System (INIS)

Kubota, Yoshihisa; Sato, Hiroshi; Koshimoto, Chihiro; Takahashi, Sentaro

1993-01-01

Cross-placental transfer of 239 Pu from the mother to fetus was studied in C3H mice. The activity of 239 Pu in the conceptus was measured 24 hrs after the intravenous injection of 239 Pu citrate on days 10.5 to 16.5 of gestation. More 239 Pu was transferred to the conceptus when the plutonium was administered in the later stages of gestation; 0.12% of the injected dose per conceptus on day 10.5 and 1.3% on day 16.5. In all the gestational stages examined, the yolk sac and decidua contained more than 89% of the total activity distributed in the conceptus. The concentration of 239 Pu in the yolk sac was about two orders of magnitude greater than that in the fetus. The 239 Pu concentration in the maternal liver decreased with the gestational stage. In the early gestational stages the concentration in the maternal liver was greater than that in the yolk sac; but, this relationship was reversed in the later stages. (author)

Observations of surface-mediated reduction of Pu(VI) to Pu(IV) on hematite nanoparticles by ATR FT-IR

Energy Technology Data Exchange (ETDEWEB)

Emerson, Hilary P. [Florida International Univ., Applied Research Center, Miami, FL (United States); Powell, Brian A. [Clemson Univ., Dept. of Enviromental Engineering and Earth Sciences, Anderson, SC (United States)

2015-07-01

Previous studies have shown that mineral surfaces may facilitate the reduction of plutonium though the mechanisms of the reduction are still unknown. The objective of this study is to use batch sorption and attenuated total reflectance Fourier transform infrared spectroscopy experiments to observe the surface-mediated reduction of plutonium on hematite nanoparticles. These techniques allow for in situ measurement of reduction of plutonium with time and may lead to a better understanding of the mechanisms of surface mediated reduction of plutonium. For the first time, ATR FT-IR peaks for Pu(VI) sorbed to hematite are measured at ∝ 916 cm{sup -1}, respectively. The decrease in peak intensity with time provides a real-time, direct measurement of Pu(VI) reduction on the hematite surface. In this work pseudo first order rate constants estimated at the high loadings (22 mg{sub Pu}/g{sub hematite}, 1.34 x 10{sup -6} M{sub Pu}/m{sup 2}) for ATR FT-IR are approximately 10 x slower than at trace concentrations based on previous work. It is proposed that the reduced rate constant at higher Pu loadings occurs after the reduction capacity due to trace Fe(II) has been exhausted and is dependent on the oxidation of water and possibly electron shuttling based on the semiconducting nature of hematite. Therefore, the reduction rate at higher loadings is possibly due to the thermodynamic favorability of Pu(IV)-hydroxide complexes.

A pilot-scale nonwoven roll goods manufacturing process reduces microbial burden to pharmacopeia acceptance levels for nonsterile hygiene applications

Science.gov (United States)

A total of seven source fiber types were selected for use in the manufacturing of nonwoven roll goods: polyester; polypropylene; rayon; greige cotton from two sources; mechanically cleaned greige cotton; and scoured and bleached cotton. The microbial burden of each source fiber was measured as a pr...

Fabrication of flexible conductive films derived from poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) on the nonwoven fabrics substrate

Energy Technology Data Exchange (ETDEWEB)

Wu, Chieh-Han [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 106, Taiwan, ROC (China); Shen, Hsiu-Ping [Department of Chemical Engineering, National Taiwan University, Taipei 106, Taiwan, ROC (China); Don, Trong-Ming, E-mail: tmdon@mail.tku.edu.tw [Department of Chemical and Materials Engineering, Tamkang University, New Taipei 251, Taiwan, ROC (China); Chiu, Wen-Yen, E-mail: ycchiu@ntu.edu.tw [Institute of Polymer Science and Engineering, National Taiwan University, Taipei 106, Taiwan, ROC (China); Department of Chemical Engineering, National Taiwan University, Taipei 106, Taiwan, ROC (China); Department of Materials Science and Engineering, National Taiwan University, Taipei 106, Taiwan, ROC (China)

2013-12-16

In this research, conducting poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) aqueous dispersion was synthesized at first via chemical oxidative polymerization and followed by mixing it with poly(styrene-r-butyl acrylate) P(St-BA) aqueous latex, creating a conductive material with outstanding stretchability. The elastic conductive composite were then film formed on the glass and poly(ethylene terephthalate) (PET) nonwoven fabric substrate by spin coating and dip coating, respectively. Composite films with various contents of PEDOT:PSS polymer (10–100 wt.%) had been prepared. From the conductivity measurements, the conductivity was still kept as high as 88 S cm{sup −1} even the PEDOT:PSS content was lowered to 10 wt.%. Furthermore, the elasticity of conductive films on the PET-nonwoven fabric substrate was evaluated by the 180° bending test repeating 100 times. With introducing soft P(St-BA) material in the PEDOT:PSS phase, the surface resistance increased merely 3–6 times after bending 100 times, while the surface resistance for pure PEDOT:PSS film could reach 18–20 times. - Highlights: • Flexible PEDOT:PSS based material had been coated on the PET-nonwoven fabrics. • The integrity of conductive circuit on fabrics was evaluated by bending test. • With adding rubbery material, the flexibility of PEDOT:PSS coating was enhanced.

Fabrication of flexible conductive films derived from poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) on the nonwoven fabrics substrate

International Nuclear Information System (INIS)

Wu, Chieh-Han; Shen, Hsiu-Ping; Don, Trong-Ming; Chiu, Wen-Yen

2013-01-01

In this research, conducting poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) (PEDOT:PSS) aqueous dispersion was synthesized at first via chemical oxidative polymerization and followed by mixing it with poly(styrene-r-butyl acrylate) P(St-BA) aqueous latex, creating a conductive material with outstanding stretchability. The elastic conductive composite were then film formed on the glass and poly(ethylene terephthalate) (PET) nonwoven fabric substrate by spin coating and dip coating, respectively. Composite films with various contents of PEDOT:PSS polymer (10–100 wt.%) had been prepared. From the conductivity measurements, the conductivity was still kept as high as 88 S cm −1 even the PEDOT:PSS content was lowered to 10 wt.%. Furthermore, the elasticity of conductive films on the PET-nonwoven fabric substrate was evaluated by the 180° bending test repeating 100 times. With introducing soft P(St-BA) material in the PEDOT:PSS phase, the surface resistance increased merely 3–6 times after bending 100 times, while the surface resistance for pure PEDOT:PSS film could reach 18–20 times. - Highlights: • Flexible PEDOT:PSS based material had been coated on the PET-nonwoven fabrics. • The integrity of conductive circuit on fabrics was evaluated by bending test. • With adding rubbery material, the flexibility of PEDOT:PSS coating was enhanced

Economical Production of Pu-238

Energy Technology Data Exchange (ETDEWEB)

Steven D. Howe; Douglas Crawford; Jorge Navarro; Terry Ring

2013-02-01

All space exploration missions traveling beyond Jupiter must use radioisotopic power sources for electrical power. The best isotope to power these sources is plutonium-238. The US supply of Pu-238 is almost exhausted and will be gone within the next decade. The Department of Energy has initiated a production program with a $10M allocation from NASA but the cost is estimated at over $100 M to get to production levels. The Center for Space Nuclear Research has conceived of a potentially better process to produce Pu-238 earlier and for significantly less cost. The new process will also produce dramatically less waste. Potentially, the front end costs could be provided by private industry such that the government only had to pay for the product produced. Under a NASA Phase I NIAC grant, the CSNR has evaluated the feasibility of using a low power, commercially available nuclear reactor to produce at least 1.5 kg of Pu-238 per year. The impact on the neutronics of the reactor have been assessed, the amount of Neptunium target material estimated, and the production rates calculated. In addition, the size of the post-irradiation processing facility has been established. In addition, a new method for fabricating the Pu-238 product into the form used for power sources has been identified to reduce the cost of the final product. In short, the concept appears to be viable, can produce the amount of Pu-238 needed to support the NASA missions, can be available within a few years, and will cost significantly less than the current DOE program.

Evaluating 239Pu levels using field detectors

International Nuclear Information System (INIS)

Wahl, L.E.; Smith, W.J. II; Martin, B.

1996-01-01

At Los Alamos National Laboratory, cleanup was planned at three septic tanks where surface soil in the outfall drainage areas was found to be contaminated with 239 Pu. To meet budget and deadline constraints, a technique was developed that used field instruments to verify 239 Pu soil contamination at levels less than 2.8 Bq g -1 , the established cleanup level. The drainage areas were surveyed using a low-energy gamma probe to identify likely areas of 239 Pu contamination. Between 40 and 135 0.1-min gamma radiation measurements were obtained from each drainage area. From these data, locations were identified for subsequent screening for alpha radioactivity. Soil samples from between 11 and 18 locations at each drainage area were placed in petri dishes, dried, and counted for 10 minutes using an alpha probe. Alpha counts were then related to 239 Pu concentrations using a curve developed from local soils containing known concentrations of 239 Pu. Up to six soil samples from each drainage area, representing a range of alpha radioactivity levels, were sent for laboratory analysis of isotopic plutonium to confirm field measurement results. Analytical and field results correlated well at all but one outfall area. At this area, field measurements predicted more 239 Pu than was measured in the laboratory, indicating the presence of another alpha-emitting radionuclide that might have been missed if only laboratory analyses for plutonium had been used. This technique, which combined a large number of gamma radioactivity measurements, a moderate number of alpha radioactivity measurements, and a few isotopic plutonium measurements, allowed quick and inexpensive comparison of 239 Pu with the cleanup level

PU.1 silencing leads to terminal differentiation of erythroleukemia cells

International Nuclear Information System (INIS)

Atar, Orna; Levi, Ben-Zion

2005-01-01

The transcription factor PU.1 plays a central role in development and differentiation of hematopoietic cells. Evidence from PU.1 knockout mice indicates a pivotal role for PU.1 in myeloid lineage and B-lymphocyte development. In addition, PU.1 is a key player in the development of Friend erythroleukemia disease, which is characterized by proliferation and differentiation arrest of proerythrocytes. To study the role of PU.1 in erythroleukemia, we have used murine erythroleukemia cells, isolated from Friend virus-infected mice. Expression of PU.1 small interfering RNA in these cells led to significant inhibition of PU.1 levels. This was accompanied by inhibition of proliferation and restoration in the ability of the proerythroblastic cells to produce hemoglobin, i.e., reversion of the leukemic phenotype. The data suggest that overexpression of PU.1 gene is the immediate cause for maintaining the leukemic phenotype of the disease by retaining the self-renewal capacity of transformed erythroblastic cells and by blocking the terminal differentiation program towards erythrocytes

Preparation and characterization of 238Pu-ceramics for radiation damage experiments

International Nuclear Information System (INIS)

DM Strachan; RD Scheele; WC Buchmiller; JD Vienna; RL Sell; RJ Elovich

2000-01-01

As a result of treaty agreements between Russia and the US, portions of their respective plutonium and nuclear weapons stockpiles have been declared excess. In support of the US Department of Energy's 1998 decision to pursue immobilization of a portion of the remaining Pu in a titanate-based ceramic, the authors prepared nearly 200 radiation-damage test specimens of five Pu- and 238 Pu-ceramics containing 10 mass% Pu to determine the effects of irradiation from the contained Pu and U on the ceramic. The five Pu-ceramics were (1) phase-pure pyrochlore [ideally, Ca(U, Pu)Ti 2 O 7 ], (2) pyrochlore-rich baseline, (3) pyrochlore-rich baseline with impurities, (4) phase-pure zirconolite [ideally Ca(U, Pu)Ti 2 O 7 ], and (5) a zirconolite-rich baseline. These ceramics were prepared with either normal weapons-grade Pu, which is predominantly 239 Pu, or 238 Pu. The 238 Pu accelerates the radiation damage relative to the 239 Pu because of its much higher specific activity. The authors were unsuccessful in preparing phase-pure (Pu, U) brannerite, which is the third crystalline phase present in the baseline immobilization form. Since these materials will contain ∼10 mass% Pu and about 20 mass% U, radiation damage to the crystalline structure of these materials will occur overtime. As the material becomes damaged from the decay of the Pu and U, it is possible for the material to swell as both the alpha particles and recoiling atoms rupture chemical bonds within the solid. As the material changes density, cracking, perhaps in the form of microcracks, may occur. If cracking occurs in ceramic that has been placed in a repository, the calculated rate of radionuclide release if the can has corroded would increase proportionately to the increase in surface area. To investigate the effects of radiation damage on the five ceramics prepared, the authors are storing the specimens at 20, 125, and 250 C until the 238 Pu specimens become metamict and the damage saturates. They will

Contribution to the study of U-Ti and U-Pu-Ti carbides; Contribution a l'etude des carbures U-C-Ti et (U, Pu) - C-Ti

Energy Technology Data Exchange (ETDEWEB)

Milet, C A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

After having discussed the reasons to use (U,Pu) carbides as fast reactor fuel, we examine the influence of the addition of titanium to these carbides. A preliminary study has been done on the system of U-C-Ti and some properties have been measured such as: density, thermal expansion, electrical resistivity, atmospheric corrosion and compatibility with stainless steel. The systems U-Pu-C-Ti (Pu/U + Pu equal to 15 per cent) and U-C-Ti have been found to be very similar. There exists a two phases region (U,Pu)C + TiC, an eutectic between (U,Pu)C and TiC for approximately 15 at %. The solubilities of U + Pu in TiC and of Ti in (U,Pu)C is less than 1 % at. The addition of titanium does not markedly change thermal expansion coefficients of (U,Pu)C. However the resistance to atmospheric corrosion and compatibility with stainless steel is improved. Thermal conductivity, calculated from electrical resistivity, has increased. On the other side, the density of fissile material is lowered. The combination of (U,Pu)C + TiC seems to be the most promising alloy for application as nuclear fuel. (author) [French] Apres avoir rappele les problemes poses par un combustible pour les reacteurs a neutrons rapides et l'interet des carbures U-Pu-C comme combustible, on examine l'influence de l'addition de titane dans ces carbures. Une etude preliminaire sur le systeme U-C-Ti a ete effectuee et quelques proprietes sont indiquees: densite, coefficients de dilatation, resistivite electrique, tenue a la corrosion atmospherique, compatibilite avec l'acier inoxydable. Le systeme U-Pu-C-Ti (Pu/U + Pu egal a 15 pour cent) presente de grandes analogies avec le systeme U-C-Ti. Il existe un domaine biphase (U,Pu)C + TiC, un eutectique entre (U,Pu)C et TiC pour environ 15 at % Ti; les solubilites de U + Pu clans TiC et de Ti dans (U,Pu)C sont inferieures a 1 at %. Par rapport a la phase (U,Pu)C, l'addition de titane est sans effets importants sur les coefficients de dilatation. Par contre la tenue a

Phase equilibrium of PuO2-x - Pu2O3 based on first-principles calculations and configurational entropy change

International Nuclear Information System (INIS)

Minamoto, Satoshi; Kato, Masato; Konashi, Kenji

2011-01-01

Combination of an oxygen vacancy formation energy calculated using first-principles approach and the configurational entropy change treated within the framework of statistical mechanics gives an expression of the Gibbs free energy at large deviation from stoichiometry of plutonium oxide PuO 2 . An oxygen vacancy formation energy 4.20 eV derived from our previously first-principles calculation was used to evaluate the Gibbs free energy change due to oxygen vacancies in the crystal. The oxygen partial pressures then can be evaluated from the change of the free energy with two fitting parameters (a vacancy-vacancy interaction energy and vibration entropy change due to induced vacancies). Derived thermodynamic expression for the free energy based on the SGTE thermodynamic data for the stoichiometric PuO 2 and the Pu 2 O 3 compounds was further incorporated into the CALPHAD modeling, then phase equilibrium between the stoichiometric Pu 2 O 3 and non-stoichiometric PuO 2-x were reproduced.

Perturbation in the 240Pu/239Pu global fallout ratio in local sediment following the nuclear accidents at Thule (Greenland) and Palomares (Spain)

International Nuclear Information System (INIS)

Mitchell, P.I.; Vintro, L.L.; Gasco, C.; Sanchez-Cabeza, J.A.

1995-01-01

It is well established that the main source of the plutonium found in marine sediments throughout the Northern Hemisphere is global stratospheric fallout, characterized by a typical 240 Pu/ 239 Pu atom ratio of ∼0.18. Measurements of perturbations in this ratio at various sites which had been subjected to close-in fallout, mainly from surface-based testing, has confirmed the feasibility of using this ratio to distinguish plutonium from different fallout sources. In the present study, the 240 Pu/ 239 Pu ratio has been examined in samples of sediment collected at Thule (Greenland) and Palomares (Spain), where accidents involving the release and dispersion of plutonium from fractured nuclear weapons occurred in 1968 and 1966, respectively. The 240 Pu/ 239 Pu ratio was measured by high-resolution alpha spectrometry and spectral deconvolution. The analytical results showed that at Thule the mean 240 Pu/ 239 Pu atom ratio was 0.033±0.004, while at Palomares the equivalent ratio appeared to be significantly higher at 0.056±0.003. Both ratios are consistent with those reported for soils samples at the Nevada site and Nagasaki, and are clearly indicative of weapons-grade plutonium. 27 refs., 1 fig., 2 tabs

Contribution to the study of the (U,Pu)C,N system; Contribution a l'etude du systeme (U,Pu)C,N

Energy Technology Data Exchange (ETDEWEB)

Lorenzelli, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The reactions of UC, PuC, (U,Pu)C, UC{sub 2} and U(C{sub 1-x}O{sub x}) with nitrogen at moderate temperatures (room temperature to 400 C) are described. The influence of the uptake of nitrogen by the powders necessary to sinter the carbides upon the nature of the final product has been investigated; it has been shown that the sintered carbides are hyper-stoichiometric. The reactions of carbon with UN, PuN and (U,Pu)N has also been studied. Under vacuum, carbon reacts on the nitrides at temperatures as low as 1100 C; nitrogen is replaced by carbon and the final product is a carbonitride. The reaction is: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. The reaction is limited and the carbonitrides have a fixed composition in presence of M{sub 2}C{sub 3} or MC{sub 2}; hence it is impossible to produce pure MC using the reaction. The ternary diagram U-C-N, Pu-C-N and (U,Pu)C-N have been drawn. They show clearly that it is possible to obtain single phase carbonitrides in a wide domain of compositions. (author) [French] On decrit les reactions avec l'azote de UC, PuC,(U,Pu)C,UC{sub 2} et U(C{sub 1-x}O{sub x}), par action directe de l'azote a temperature moderee (de l'ambiante a 450 C). On a etudie l'influence de la contamination par l'azote des poudres de carbures necessaires au frittage sur la nature des produits frittes; on a montre que les carbures frittes obtenus sont hyperstoechiometriques. On a etudie parallelement les reactions du carbone avec UN, PuN et (U,Pu)N. Sous vide le carbone reagit sur les nitrures des 1100 C: le carbone se substitue a l'azote; l'azote libere est elimine et le produit final est un carbonitrure. La reaction s'ecrit: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. La reaction est limitee et les carbonitrures obtenus ont une composition limite fixe en presence des carbures superieurs M{sub 2}C{sub 3} et MC{sub 2}; il est donc impossible d'obtenir MC pur par cette reaction. Les diagrammes d'equilibre U-C-N, Pu-C-N et (U,Pu) C-N, ont

Effect of microdose distribution on chromosome aberration frequency in liver cells of the Chinese hamster following exposure to 239PuO2 or 238PuO2 particles

International Nuclear Information System (INIS)

Brooks, A.L.; Peters, R.F.; Retherford, J.C.

1974-01-01

Chinese hamsters were injected intravenously with 239 PuO 2 or 238 PuO 2 particles of known size or with 238 Pu citrate to determine the effect of particle size and specific activity on the frequency and distribution of chromosome damage in the liver. Three particle sizes were used in the 239 PuO 2 experiment: 0.15, 0.44, and 0.89 μm, and all animals were injected with a constant activity, 5 x 10 -4 muCi 239 Pu/gm body weight. The 238 PuO 2 was injected in three particle sizes, 0.17, 0.41, and 1.1 μm and at three activity levels. The 238 Pu citrate was injected at 5 x 10 -3 muCi 238 Pu/gm body weight. Hamsters injected with 239 PuO 2 were sacrificed at 15, 42, and 122 days after injection and those injected with either 238 PuO 2 or 238 Pu citrate were sacrificed 12 days after injection. The number of alpha tracks/star increased as a function of the particle size injected. A change in particle size with time was noted as smaller particles were aggregated into larger ones by the phagocytic action of Kupffer cells. Injection of 239 PuO 2 and 238 PuO 2 produced a distribution of chromosome damage which was non-poison in nature. 239 PuO 2 produced increased damage with increasing average dose with some cells containing a large number of aberrations, but there was relatively little particle size effect. Conversely, aberration frequencies after 238 PuO 2 injection were inversely related to particle size and no cells were seen with large amounts of damage. The 238 Pu citrate produced 6 x 10 -3 aberrations/cell/rad which was a higher rate than observed for 238 Pu particles. Risk for the production of cellular damage in the liver was greater per μCi following injection of either 238 Pu or 239 Pu citrate than it was following deposition of the same amount of 239 PuO 2 or 238 PuO 2 particles. (U.S.)

Thermo-responsive wound dressings by grafting chitosan and poly(N-isopropylacrylamide) to plasma-induced graft polymerization modified non-woven fabrics

International Nuclear Information System (INIS)

Chen, Jyh-Ping; Kuo, Chang-Yi; Lee, Wen-Li

2012-01-01

Highlights: ► Poly(N-isopropylacrylamide) and chitosan were grafted to polypropylene non-wovens. ► An easily stripped off thermo-responsive wound dressing was developed. ► The wound dressing is biocompatible, has antibacterial and wound healing abilities. ► The bigraft non-woven will be a potential wound dressing for biomedical use. - Abstract: To obtain a chitosan wound dressings with temperature-responsive characteristics, polypropylene (PP) non-woven fabric (NWF) was modified by direct current pulsed oxygen plasma-induced grafting polymerization of acrylic acid (AAc) to improve hydrophilicity and to introduce carboxylic acid groups. Conjugation of chitosan and poly(N-isopropylacrylamide) (PNIPAAm) followed by using water-soluble carbodiimide as a coupling agent to form a novel bigraft PP-g-chitosan-g-PNIPAAm wound dressing. The amount of chitosan and PNIPAAm grafted to PP-g-chitosan-g-PNIPAAm were 83.0 ± 4.6 μg/cm 2 and 189.5 ± 8.2 μg/cm 2 , respectively. The surface chemical composition and microstructure of the NWF were studied by electron spectroscopy for chemical analysis (ESCA) and scanning electron microscopy (SEM). The linkages between AAc, chitosan, and PNIPAAm were confirmed with the formation of amide bonds. Physical properties of the NWF were characterized and potentials of these NWFs as wound dressings were evaluated using SD rat as the animal model. NWFs contained PNIPAAm were better than those contained only chitosan in wound healing rates and the wound areas covered by PP-g-chitosan-g-PNIPAAm wound dressings healed completely in 17 days.

Estimation of human gonadal Pu and Ce concentrations from animal data

International Nuclear Information System (INIS)

Thomas, R.G.; Durbin, P.W.; McInroy, J.F.; Healy, J.W.

1989-01-01

Data were obtained from the literature for gonad and body weights and for the Pu or Ce content of the gonads and body at death for several laboratory animal species, five human Pu injection cases, and 731 human adults exposed environmentally to Pu in fallout. Data for Pu concentration in gonads, liver, and bone samples of 59 male and five female occupational Pu cases (including four completely analyzed whole bodies) were obtained from the U.S. Transuranium Registry. A logarithmic function was used to relate fractional Pu or Ce concentration in testes and ovaries to body weight of the animals and to predict fractional Pu or Ce concentrations in human gonads, [Pu]G . PuB-1 = aBWb, where [Pu]G or [Ce]G is the nuclide concentration in gonads (Bq g-1 of wet weight), PuB or CeB is the nuclide content of the body at death, and BW is body weight (kg). The fractional Pu and Ce concentrations in both the testes and ovaries are inverse and nearly linear functions of body weight. The regression lines of fractional Pu or Ce concentration in testes and ovaries have similar slopes (b = -1.07 +/- 0.14); however, the nuclide concentrations (coefficient a) in ovaries are six times greater than in testes. Extrapolation of the animal data yielded fractional Pu concentrations in human testes and ovaries that agree with those calculated for the occupational cases and those recommended by the International Commission on Radiological Protection. The good agreement between the fractional concentrations of Pu and Ce in the testes and in the ovaries suggests that these data can be substituted in metabolic models of chemically similar elements for which gonadal data are scarce

Effect of thermal-treatment sequence on sound absorbing and mechanical properties of porous sound-absorbing/thermal-insulating composites

Directory of Open Access Journals (Sweden)

Huang Chen-Hung

2016-01-01

Full Text Available Due to recent rapid commercial and industrial development, mechanical equipment is supplemented massively in the factory and thus mechanical operation causes noise which distresses living at home. In livelihood, neighborhood, transportation equipment, jobsite construction noises impact on quality of life not only factory noise. This study aims to preparation technique and property evaluation of porous sound-absorbing/thermal-insulating composites. Hollow three-dimensional crimp PET fibers blended with low-melting PET fibers were fabricated into hollow PET/low-melting PET nonwoven after opening, blending, carding, lapping and needle-bonding process. Then, hollow PET/low-melting PET nonwovens were laminated into sound-absorbing/thermal-insulating composites by changing sequence of needle-bonding and thermal-treatment. The optimal thermal-treated sequence was found by tensile strength, tearing strength, sound-absorbing coefficient and thermal conductivity coefficient tests of porous composites.

Direct reduction of 238PuO2 and 239PuO2 to metal

International Nuclear Information System (INIS)

Mullins, L.J.; Foxx, C.L.

1982-02-01

The process for reducing 700 g 239 PuO 2 to metal is a standard procedure at Los Alamos National Laboratory. This process is based on research for reducing 200 g 238 PuO 2 to metal. This report describes in detail the experiments and development of the 200-g process. The procedure uses calcium metal as the reducing agent in a molten CaCl 2 solvent system. The process to convert impure plutonia to high-purity metal by oxide reduction followed by electrorefining is also described

A 233U/236U/242Pu/244Pu spike for isotopic and isotope dilution analysis by mass spectrometry with internal calibration

International Nuclear Information System (INIS)

Stepanov, A.; Belyaev, B.; Buljanitsa, L.

1989-11-01

The Khlopin Radium Institute prepared on behalf of the IAEA a synthetic mixture of 233 U, 236 U, 242 Pu and 244 Pu isotopes. The isotopic composition and elemental concentration of uranium and plutonium were certified on the basis of analyses done by four laboratories of the IAEA Network, using mass spectrometry with internal standardization. The certified values for 233 U/ 236 U ratio and the 236 U chemical concentration have a coefficient of variation of 0.05%. The latter is fixed by the uncertainty in the 235 U/ 238 U ratio of NBS500 used as internal standard. The coefficients of variation of the 244 Pu/ 242 Pu ratio and the 242 Pu chemical concentration are respectively 0.10% and 0.16% and limited by the uncertainty in the 240 Pu/ 239 Pu ratio of NBS947. This four isotope mixture was used as an internal standard as well as a spike, to analyze 30 batches of LWR spent fuel solutions. The repeatability of the mass spectrometric measurements have a coefficient of variation of 0.025% for the uranium concentration, and of 0.039% for the plutonium concentration. The spiking and treatment errors had a coefficient of variation of 0.048%. (author). Refs, figs and tabs

Vertical distribution of 241Pu in the southern Baltic Sea sediments

International Nuclear Information System (INIS)

Strumińska-Parulska, Dagmara I.

2014-01-01

Highlights: • The unique study on 241 Pu in sediments from the southern Baltic Sea was presented. • 241 Pu was determined using alpha spectrometry by indirect method. • The biggest amount of 241 Pu existed in the surface layers of all analyzed sediments. • The highest 241 Pu amount comes from the Chernobyl accident. - Abstract: The vertical distribution of plutonium 241 Pu in marine sediments can assist in determining the deposition history and sedimentation process of analyzed regions. In addition, 241 Pu/ 239+240 Pu activity ratio could be used as a sensitive fingerprint for radioactive source identification. The present preliminary studies on vertical distribution of 241 Pu in sediments from four regions of the southern Baltic Sea are presented. The distribution of 241 Pu was not uniform and depended on sediment geomorphology and depth as well as location. The highest concentrations of plutonium were found in the surface layers of all analyzed sediments and originated from the Chernobyl accident

The production of {sup 238-242}Pu(n,γ){sup 239-243}Pu fissionable fluids in a fusion-fission hybrid reactor

Energy Technology Data Exchange (ETDEWEB)

Guenay, Mehtap [Inoenue Univ., Malatya (Turkey). Physics Dept.

2014-03-15

In this study, the effect of spent fuel grade plutonium content on {sup 239-243}Pu was investigated in a designed hybrid reactor system. In this system, the fluids were composed of a molten salt, heavy metal mixture with increased mole fractions 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-Pu, 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-PuF{sub 4}, 99-95 % Li{sub 20}Sn{sub 80}-1-5 % SFG-PuO{sub 2}. Beryllium (Be) is a neutron multiplier by (n,2n) reactions. Thence, a Be zone of 3 cm thickness was used in order to contribute to fissile fuel breeding between the liquid first wall and a 9Cr2WVTa ferritic steel blanket which is used as structural material. The production of {sup 238-242}Pu(n,γ){sup 239-243}Pu was calculated in liquid first wall, blanket and shielding zones. Three-dimensional nucleonic calculations were performed by using the most recent version MCNPX-2.7.0 Monte Carlo code and nuclear data library ENDF/B-VII.0. (orig.)

238Pu fuel form activities, March 1-September 30, 1985

International Nuclear Information System (INIS)

1986-01-01

The SRP portion of this report summarizes production 238 PuO 2 fuel forms for use in radioisotopic thermoelectric generators (RTG's) in the Plutonium Fuel Form (PuFF) Facility at the Savannah River Plant. The PuFF Facility began producing iridium-encapsulated, 62.5-watt 238 PuO 2 right circular cylinders for GPHS (General Purpose Heat Source) RTG's in June 1980; this program was completed in December 1983. The PuFF Facility has been placed in a production readiness mode of operation pending funding of additional heat source programs

Surrogate 239Pu(n, fxn) and 241Pu(n, fxn) average fission-neutron-multiplicity measurements

Energy Technology Data Exchange (ETDEWEB)

Burke, J. T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Alan, B. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Akindele, O. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Casperson, R. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hughes, R. O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fisher, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-26

We have constructed a new neutron-charged-particle detector array called NeutronSTARS. It has been described extensively in LLNL-TR-703909 [1] and Akindele et al [2]. We have used this new neutron-charged-particle array to measure the 241Pu and 239Pu fissionneutron multiplicity as a function of equivalent incident-neutron energy from 100 keV to 20 MeV. The experimental approach, detector array, data analysis, and results are summarized in the following sections.

Internal Corrosion Analysis of Model 9975 Packaging Containing Pu or PuO2 During Shipping and Storage

International Nuclear Information System (INIS)

Vormelker, P.

1999-01-01

The Materials Consultation Group of SRTC has completed an internal corrosion analysis of the Model 9975 packaging assembly containing either Pu or PuO2 for storage in K Reactor under ambient conditions for a period of 12 years. The 12-year storage period includes two years for shipping and up to ten years for storage

Pu(V) as the stable form of oxidized plutonium in natural waters

International Nuclear Information System (INIS)

Orlandini, K.A.; Penrose, W.R.; Nelson, D.M.

1986-01-01

This work presents analytical evidence supporting the proposition that Pu(V) is the sole or predominant form of oxidized plutonium in natural waters. Two independent methods, the selective adsorption of Pu(VI) by silica gel, and the somewhat less selective coprecipitation of Pu(V) with calcium carbonate, were developed to separate Pu(V) from Pu(VI). Measurements of ambient plutonium in several natural waters by these methods found only Pu(V). In laboratory tracer studies, Pu(VI) was shown to be highly unstable in dilute bicarbonate solution and in Lake Michigan water, reducing in first-order fashion to Pu(V). (orig.)

Determination of Pu and U by ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Muramatsu, Y.; Yoshida, S. [National Inst. of Radiological Sciences, Chiba (Japan)

2002-06-01

In order to understand the distribution and behaviour of long-lived radionuclides in the terrestrial environment, we have developed analytical methods for {sup 238}U, {sup 232}Th and {sup 239},{sup 240}Pu and determined them in several environmental samples. ICP-MS was applied to the analyses. Concentrations of {sup 238}U and {sup 232}Th were determined in variety of soils, plants and environmental waters. The mean concentration of U and Th in 77 soils, collected several parts of Japan, were 2.3 and 7.0 ppm (dry wt). Red and yellow soils, which are mainly found in western Japan, have high concentrations of Th, suggesting the contribution from granitic rocks. Higher concentration of U in agricultural soils than forest soils suggested the possible accumulation of this element from phosphate fertilizer. The soil-to-plant transfer factors (concentration ratios between plants and soils) of U and Th were estimated from the analytical results of these nuclides in soils and in several crops. The factors for U were about 0.0005 in leaf vegetables, 0.0002 in root vegetables, 0.0001 in potatoes and 0.00001 in rice (polished). For Th, the factors were about 0.0005 in leaf vegetables, 0.0008 in root vegetables, 0.0005 in potatoes and 0.00003 in rice (polished). For the analysis of plutonium, chromatographic resin, Dowex 1x8, was examined for their applicability in the separation of Pu from the matrix elements. Sufficient decontamination factors (10{sup 4}-10{sup 5}) for many matrix elements including U, which interferes in the detection of mass 239, were obtained in both resins. Analytical results of {sup 239+240}Pu in standard reference materials (IAEA-135, -SOIL-6, -368 and -134) indicated that the accuracy of this method was satisfactory. Data on the {sup 240}Pu/{sup 239}Pu atom ratios in these reference materials, which are rare in the literature, were also obtained. Soil samples from the Marshall Islands showed a large variation of the {sup 240}Pu/{sup 239}Pu atom ratios

Status of 239Pu evaluations

International Nuclear Information System (INIS)

Kawano, Toshihiko; Talou, Patrick; Chadwick, Mark B.

2014-01-01

This paper summarises the current status of nuclear data evaluations for n+ 239 Pu. The nuclear data we address include fission, capture, scattering cross-sections, as well as the prompt fission neutron energy spectrum, which has large sensitivities to the criticality benchmark testing. The evaluated nuclear data files currently available for 239 Pu are compared, and the source of differences in the cross-sections are discussed. Some open questions on the statistical model calculations for deformed systems are also given. (authors)

Biosorption of 239Pu by immobilized sargassum fusiforme

International Nuclear Information System (INIS)

Liang Zhirong; Chen Qi; Wu Yusheng

2009-01-01

Sargassum fusiforme was immobilized with calcium alginates and its biosorption property to 239 Pu was studied by batch and column methods. Biosorption equilibrium time of immobilized Sargassum fusiforme biosorbent to 239 Pu is 120 min and biosorption efficiency is over 99.2% when the initial concentration of 239 Pu is 21.5 kBq/L and pH is 2.5-5.0. After five times repetition biosorption-desorption cycles biosorption efficiency is still over 98.0% when the velocity of flow is 2 ml/min in column experiment. Immobilized Sargassum fusiforme biosorbent is better to 239 Pu due to its better chemical stability, mechanical strength, lower cost, high biosorption efficiency and repeated biosorption-desorption cycles. (authors)

Direct-write PVDF nonwoven fiber fabric energy harvesters via the hollow cylindrical near-field electrospinning process

International Nuclear Information System (INIS)

Liu, Z H; Pan, C T; Ou, Z Y; Lin, L W; Huang, J C

2014-01-01

One-dimensional piezoelectric nanomaterials have attracted great attention in recent years for their possible applications in mechanical energy scavenging devices. However, it is difficult to control the structural diameter, length, and density of these fibers fabricated by micro/nano-technologies. This work presents a hollow cylindrical near-field electrospinning (HCNFES) process to address production and performance issues encountered previously in either far-field electrospinning (FFES) or near-field electrospinning (NFES) processes. Oriented polyvinylidene fluoride (PVDF) fibers in the form of nonwoven fabric have been directly written on a glass tube for aligned piezoelectricity. Under a high in situ electrical poling field and strong mechanical stretching (the tangential speed on the glass tube collector is about 1989.3 mm s −1 ), the HCNFES process is able to uniformly deposit large arrays of PVDF fibers with good concentrations of piezoelectric β-phase. The nonwoven fiber fabric (NFF) is transferred onto a polyethylene terephthalate (PET) substrate and fixed at both ends using copper foil electrodes as a flexible textile-fiber-based PVDF energy harvester. Repeated stretching and releasing of PVDF NFF with a strain of 0.05% at 7 Hz produces a maximum peak voltage and current at 76 mV and 39 nA, respectively. (paper)

Abaca/polyester nonwoven fabric functionalization for metal ion adsorbent synthesis via electron beam-induced emulsion grafting

Science.gov (United States)

Madrid, Jordan F.; Ueki, Yuji; Seko, Noriaki

2013-09-01

A metal ion adsorbent was developed from a nonwoven fabric trunk material composed of both natural and synthetic polymers. A pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca/polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on absorbed dose, reaction time and monomer concentration were evaluated. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3 h reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 °C, a grafted APNWF with a Dg greater than 150% was obtained. The GMA-grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 °C to introduce amine functional groups. After a 3 h reaction with 50% EDA, an amine group density of 2.7 mmole/gram adsorbent was achieved based from elemental analysis. Batch adsorption experiments were performed using Cu2+ and Ni2+ ions in aqueous solutions with initial pH of 5 at 30 °C. Results show that the adsorption capacity of the grafted adsorbent for Cu2+ is four times higher than Ni2+ ions.

Contribution to the study of the (U,Pu)C,N system; Contribution a l'etude du systeme (U,Pu)C,N

Energy Technology Data Exchange (ETDEWEB)

Lorenzelli, R. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The reactions of UC, PuC, (U,Pu)C, UC{sub 2} and U(C{sub 1-x}O{sub x}) with nitrogen at moderate temperatures (room temperature to 400 C) are described. The influence of the uptake of nitrogen by the powders necessary to sinter the carbides upon the nature of the final product has been investigated; it has been shown that the sintered carbides are hyper-stoichiometric. The reactions of carbon with UN, PuN and (U,Pu)N has also been studied. Under vacuum, carbon reacts on the nitrides at temperatures as low as 1100 C; nitrogen is replaced by carbon and the final product is a carbonitride. The reaction is: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. The reaction is limited and the carbonitrides have a fixed composition in presence of M{sub 2}C{sub 3} or MC{sub 2}; hence it is impossible to produce pure MC using the reaction. The ternary diagram U-C-N, Pu-C-N and (U,Pu)C-N have been drawn. They show clearly that it is possible to obtain single phase carbonitrides in a wide domain of compositions. (author) [French] On decrit les reactions avec l'azote de UC, PuC,(U,Pu)C,UC{sub 2} et U(C{sub 1-x}O{sub x}), par action directe de l'azote a temperature moderee (de l'ambiante a 450 C). On a etudie l'influence de la contamination par l'azote des poudres de carbures necessaires au frittage sur la nature des produits frittes; on a montre que les carbures frittes obtenus sont hyperstoechiometriques. On a etudie parallelement les reactions du carbone avec UN, PuN et (U,Pu)N. Sous vide le carbone reagit sur les nitrures des 1100 C: le carbone se substitue a l'azote; l'azote libere est elimine et le produit final est un carbonitrure. La reaction s'ecrit: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. La reaction est limitee et les carbonitrures obtenus ont une composition limite fixe en presence des carbures superieurs M{sub 2}C{sub 3} et MC{sub 2}; il est donc impossible d'obtenir MC pur par cette reaction. Les diagrammes

DFT and two-dimensional correlation analysis methods for evaluating the Pu3+–Pu4+ electronic transition of plutonium-doped zircon

International Nuclear Information System (INIS)

Bian, Liang; Dong, Fa-qin; Song, Mian-xin; Dong, Hai-liang; Li, Wei-Min; Duan, Tao; Xu, Jin-bao; Zhang, Xiao-yan

2015-01-01

Highlights: • Effect of Pu f-shell electron on the electronic property of zircon is calculated via DFT and 2D-CA techniques. • Reasons of Pu f-shell electron influencing on electronic properties are systematically discussed. • Phase transitions are found at two point 2.8 mol% and 7.5 mol%. - Abstract: Understanding how plutonium (Pu) doping affects the crystalline zircon structure is very important for risk management. However, so far, there have been only a very limited number of reports of the quantitative simulation of the effects of the Pu charge and concentration on the phase transition. In this study, we used density functional theory (DFT), virtual crystal approximation (VCA), and two-dimensional correlation analysis (2D-CA) techniques to calculate the origins of the structural and electronic transitions of Zr 1−c Pu c SiO 4 over a wide range of Pu doping concentrations (c = 0–10 mol%). The calculations indicated that the low-angular-momentum Pu-f xy -shell electron excites an inner-shell O-2s 2 orbital to create an oxygen defect (V O-s ) below c = 2.8 mol%. This oxygen defect then captures a low-angular-momentum Zr-5p 6 5s 2 electron to form an sp hybrid orbital, which exhibits a stable phase structure. When c > 2.8 mol%, each accumulated V O-p defect captures a high-angular-momentum Zr-4d z electron and two Si-p z electrons to create delocalized Si 4+ → Si 2+ charge disproportionation. Therefore, we suggest that the optimal amount of Pu cannot exceed 7.5 mol% because of the formation of a mixture of ZrO 8 polyhedral and SiO 4 tetrahedral phases with the orientation (10-1). This study offers new perspective on the development of highly stable zircon-based solid solution materials

Investigation of the oxidation states of Pu isotopes in a hydrochloric acid solution

Energy Technology Data Exchange (ETDEWEB)

Lee, M.H. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)], E-mail: mhlee@kaeri.re.kr; Kim, J.Y.; Kim, W.H.; Jung, E.C.; Jee, K.Y. [Nuclear Chemistry Research Division, Korea Atomic Energy Research Institute, P. O. Box 105, Yuseong, Daejeon 305-353 (Korea, Republic of)

2008-12-15

The characteristics of the oxidation states of Pu in a hydrochloric acid solution were investigated and the results were applied to a separating of Pu isotopes from IAEA reference soils. The oxidation states of Pu(III) and Pu(IV) were prepared by adding hydroxylamine hydrochloride and sodium nitrite to a Pu stock solution, respectively. Also, the oxidation state of Pu(VI) was adjusted with concentrated HNO{sub 3} and HClO{sub 4}. The stability of the various oxidation states of plutonium in a HCl solution with elapsed time after preparation were found to be in the following order: Pu(III){approx}Pu(VI)>Pu(IV)>Pu(V). The chemical recoveries of Pu(IV) in a 9 M HCl solution with an anion exchange resin were similar to those of Pu(VI). This method for the determination of Pu isotopes with an anion exchange resin in a 9 M HCl medium was applied to IAEA reference soils where the activity concentrations of {sup 239,240}Pu and {sup 238}Pu in IAEA-375 and IAEA-326 were consistent with the reference values reported by the IAEA.

Determination of 240Pu/239Pu isotopic ratios in human tissues collected from areas around the Semipalatinsk Nuclear Test Site by sector-field high resolution ICP-MS.

Science.gov (United States)

Yamamoto, M; Oikawa, S; Sakaguchi, A; Tomita, J; Hoshi, M; Apsalikov, K N

2008-09-01

Information on the 240Pu/239Pu isotope ratios in human tissues for people living around the Semipalatinsk Nuclear Test Site (SNTS) was deduced from 9 sets of soft tissues and bones, and 23 other bone samples obtained by autopsy. Plutonium was radiochemically separated and purified, and plutonium isotopes (239Pu and 240Pu) were determined by sector-field high resolution inductively coupled plasma-mass spectrometry. For most of the tissue samples from the former nine subjects, low 240Pu/239Pu isotope ratios were determined: bone, 0.125 +/- 0.018 (0.113-0.145, n = 4); lungs, 0.063 +/- 0.010 (0.051-0.078, n = 5); and liver, 0.148 +/- 0.026 (0.104-0.189, n = 9). Only 239Pu was detected in the kidney samples; the amount of 240Pu was too small to be measured, probably due to the small size of samples analyzed. The mean 240Pu/239Pu isotope ratio for bone samples from the latter 23 subjects was 0.152 +/- 0.034, ranging from 0.088 to 0.207. A significant difference (a two-tailed Student's t test; 95% significant level, alpha = 0.05) between mean 240Pu/239Pu isotope ratios for the tissue samples and for the global fallout value (0.178 +/- 0.014) indicated that weapons-grade plutonium from the atomic bombs has been incorporated into the human tissues, especially lungs, in the residents living around the SNTS. The present 239,240Pu concentrations in bone, lung, and liver samples were, however, not much different from ranges found for human tissues from other countries that were due solely to global fallout during the 1970's-1980's.

Inhaled 239PuO2 in rats with pulmonary emphysema

International Nuclear Information System (INIS)

Lundgren, D.L.; Mauderly, J.L.; Hahn, F.F.

1984-01-01

The modifying effects of a pre-existing lung disease (emphysema) on the deposition, distribution, retention, and effects of inhaled 239 PuO 2 in the rat are being investigated. Preliminary observations indicated that the deposition and retention patterns for 239 Pu particles inhaled by rats with emphysema and control rats were similar, but the distribution of inhaled 239 Pu immediately after exposure was different. Respiratory function measured through one year after exposure to 239 Pu was consistent with emphysema and was not altered by the 239 Pu lung burden. Long-term observations are continuing. 4 references, 2 tables

Measurement of the fission cross-section of $^{240}$Pu and $^{242}$Pu at CERN's n_TOF Facility

CERN Multimedia

Pavlik, A F; Gonzalez romero, E M

The n_TOF Collaboration proposes to continue the fission program, already started in 2002-2004, taking advantage of the newly constructed Work Sector Type A, with the measurement of the two isotopes : $^{240}$ Pu and $^{242}$ Pu. They are both of major importance for reactor physics applications and are included in the Nuclear Energy Agency (NEA) High Priority List [1], in the NEA WPEC Subgroup 26 Report on the accuracy of nuclear data for advanced reactor designe [2] and in the EU 6$^{th}$ Framework Programme IP-EUROTRANS/NUDATRA reports [3]. Based on those requests, the measurement of the fission cross-section of the two Pu isotopes is one of the objectives of the project ANDES of the FP7 EURATOM program [4].

A 244Pu spike reference material CBNM IRM-042A

International Nuclear Information System (INIS)

Verbruggen, A.; Gallet, M.; Hendrickx, F.; Bievre, P. de

1991-01-01

An highly enriched 244 Pu isotopic reference material (CBNM IRM-042a) has been prepared and certified for 244 Pu isotope concentration. The certified value of (2.257 7 ± 0.004 4).10 18 atoms 242 Pu.kg -1 of solution has been established by isotope dilution mass spectrometry. The plutonium isotopic composition has been determined by thermal ionization mass spectrometry and calibration of these measurements by means of synthetic 242 Pu/ 239 Pu mixtures. The isotopic reference material is supplied in a sealed glass ampoule containing approximately 10 g of a 5M nitric acid solution at an approximate concentration of 1 μg Pu per g solution. This isotopic reference material is part of a systematic CBNM programme to supply spike isotopic reference materials of various isotopes at different concentrations

Sequential determination of {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am and {sup 90}Sr in radioactive wastes using SPE sorbents Analig Pu02, AnaLig Sr01 and TRU Resin; Sekvencne stanovenie {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am a {sup 90}Sr v radioaktivnych odpadoch pouzitim SPE sorbentov Analig Pu02, AnaLig Sr01 a TRU Resin

Energy Technology Data Exchange (ETDEWEB)

Durkot, E; Dulanska, S [Univerzita Komenskeho v Bratislave, Prirodovedecka fakulta, Katedra jadrovej chemie, 84215 Bratislava (Slovakia)

2012-04-25

A simple and rapid method of the sequential determination of radionuclides {sup 239,240}Pu, {sup 238} Pu, {sup 241} Am and {sup 90}Sr in radioactive sludge from the NPP Bohunice A1 with high radiochemical yields and efficient removal of interfering components from a matrix was developed. Separation method combines SPE sorbents Analig Pu02, AnaLig Sr01 made by IBC Advanced Technologies and TRU Resin (Eichrom Technologies) placed in tandem. Advantage of a single-stage column located on the vacuum box with a rapid flow is an effective pre-concentration and separation of radionuclides and minimization of sample separation time. (authors)

The impact of Pu speciation on distribution coefficients in Mayak soil.

Science.gov (United States)

Skipperud, L; Oughton, D; Salbu, B

2000-08-10

To assess the long-term consequences when radionuclides are released into the environment, information on the source term, transport and transformation processes, interaction with soils (KD) and biological uptake (CF) is needed. Among the artificial radionuclides released to the environment by nuclear activities, the transuranium elements are a major concern, due to very long half-lives and their accumulation in bone as well as high radiotoxicity. Plutonium has been produced in greater quantity than other transuranic elements, however, environmental assessments are complicated by the complex environmental behaviour. Physico-chemical forms of Pu will determine the interactions with soils and, thus, the degree to which soils can act as a sink or a potential diffuse source of contaminants. In the present work, dynamic tracer experiments have been performed where different Pu-species are added to a 'Mayak soil-rainwater system' to obtain information on KD values. After a defined contact time, the samples where then sequentially extracted and results are used in a dynamic box model to estimate interaction and fixation rates. The interaction of all Pu-species with soils seems to be rapid and follows a two-step reaction. Up to contact times of a few weeks, the KD for Pu(III,IV) (730 +/- 240 l/kg) is approximately one order of magnitude higher than for Pu(V,VI) (90 +/- 20 l/kg) and Pu(III,IV)-organic (40-60 l/kg). After 3 months contact time, the KD in only the two organic-bound Pu-species were significantly lower. This shows that the initial association with the soil is dependent on the Pu-species in the rainwater. After only 1 h of contact, between 33 and 40% of the plutonium was strongly bound to the soil components, i.e. only extractable with strong HNO3. The extraction of soil-bound Pu followed a similar pattern for all the original species, suggesting that the next step of Pu interaction mechanism with soil was rather independent of the original species. For both the

Radiative capture on $^{242}$Pu for MOX fuel reactors

CERN Multimedia

The use of MOX fuel (mixed-oxide fuel made of UO$_{2}$ and PuO$_{2}$) in nuclear reactors allows substituting a large fraction of the enriched Uranium by Plutonium reprocessed from spent fuel. Indeed around 66% of the plutonium from spent fuel is made of $^{239}$Pu and $^{241}$Pu, which are fissile in thermal reactors. A typical reactor of this type uses a fuel with 7% reprocessed Pu and 93% depleted U, thus profiting from both the spent fuel and the remaining $^{238}$U following the $^{235}$U enrichment. With the use of such new fuel compositions rich in Pu the better knowledge of the capture and fission cross sections of the Pu isotopes becomes very important. This is clearly stated in the recent OECD NEA’s “High Priority Request List” and in the WPEC-26 “Uncertainty and target accuracy assessment for innovative systems using recent covariance data evaluations” report. In particular, a new series of cross section evaluations have been recently carried out jointly by the European (JEFF) and United ...

239,240Pu distribution in the Japanese

International Nuclear Information System (INIS)

Hisamatsu, Shun-ichi

1996-01-01

Distribution of 239,240 Pu and 241 Am in the Japanese were reviewed, and compared with those estimated with ICRP metabolic models. Inhalation and ingestion amount of these nuclides were calculated from simple models, and used as input to the ICRP metabolic models. ICRP-30 model or the combination of ICRP-66 lung model and ICRP-67 metabolic model were used for the calculation. The estimated 239,240 Pu concentrations in lung, liver, skeleton, kidney and muscle by using of the combination of ICRP-66 and 67 models agreed well with the measured data in most cases. The contribution of ingestion intake to body burden of 239,240 Pu was estimated to be 12% with 5 x 10 -4 as f 1 value. The combination of ICRP-66 and 67 model could described fairly well the organ burden of 241 Am measured in Akita and Niigata district. The 241 Am grown from 241 Pu in the human body was calculated to contribute 90% of the burden. (author)

Mechanical properties of 238PuO2

International Nuclear Information System (INIS)

Petrovic, J.J.; Hecker, S.S.; Land, C.C.; Rohr, D.L.

1977-04-01

The mechanical properties of 238 PuO 2 have been examined in the Los Alamos Scientific Laboratory mechanical test facility built to handle α-radioactive materials. Compression tests were conducted as a function of temperature, strain rate, grain size, density, and storage time. At temperatures less than or equal to 1400 0 C, test specimens of 238 PuO 2 exhibit pseudobrittle behavior due to internal cracks. Plastic deformation is ''localized'' at the crack tips. Generalized plastic deformation is observed at 1500 0 C. Ultimate stress values decrease markedly with increasing temperature and decreasing strain rate, and decrease less with decreasing density, increasing storage time, and increasing grain size. Room temperature fracture is transgranular, whereas intergranular fracture predominates at elevated temperatures. Crack-free specimens of 239 PuO 2 exhibit extensive plastic deformation at 1000 0 C and above. The relationship of these test results to the impact properties of 238 PuO 2 fuel in radioisotope thermoelectric generators is discussed

PuMA: the Porous Microstructure Analysis software

Science.gov (United States)

Ferguson, Joseph C.; Panerai, Francesco; Borner, Arnaud; Mansour, Nagi N.

2018-01-01

The Porous Microstructure Analysis (PuMA) software has been developed in order to compute effective material properties and perform material response simulations on digitized microstructures of porous media. PuMA is able to import digital three-dimensional images obtained from X-ray microtomography or to generate artificial microstructures. PuMA also provides a module for interactive 3D visualizations. Version 2.1 includes modules to compute porosity, volume fractions, and surface area. Two finite difference Laplace solvers have been implemented to compute the continuum tortuosity factor, effective thermal conductivity, and effective electrical conductivity. A random method has been developed to compute tortuosity factors from the continuum to rarefied regimes. Representative elementary volume analysis can be performed on each property. The software also includes a time-dependent, particle-based model for the oxidation of fibrous materials. PuMA was developed for Linux operating systems and is available as a NASA software under a US & Foreign release.

Electrocatalytic performance of Pu(IV)/Pu(III) redox reaction at graphene modified glassy carbon electrode

International Nuclear Information System (INIS)

Gupta, Ruma; Gamare, J.S.; Kamat, J.V.; Aggarwal, S.K.

2014-01-01

In this paper we explore the analytical perspectives of graphene modified electrode utilising commercially available graphene, which is well characterised, completely free from surfactants and has not been purposely oxidised or treated. We compare and critically contrast the electro-analytical performance of graphene modified glassy carbon electrodes (Gr/GC) with that of unmodified GC electrode towards Pu(IV)/Pu(III) redox reaction, monitoring of which has considerable importance in a plethora of areas where electrochemistry is conveniently and beneficially utilised for determination of nuclear fuels

Savannah River Laboratory monthly report: 238Pu fuel form processes

International Nuclear Information System (INIS)

1976-01-01

Progress in the Savannah River 238 Pu Fuel Form Program is discussed. Goals of the Savannah River Laboratory (SRL) program are to provide technical support for the transfer of the 238 Pu fuel form fabrication operations from Mound Laboratory to new facilities being built at the Savannah River Plant (SRP), to provide the technical basis for 238 Pu scrap recovery at SRP, and to assist in sustaining plant operations. During the period it was found that the density of hot-pressed 238 PuO 2 pellets decreased as the particle size of ball-milled powder decreased;the surface area of calcined 238 PuO 2 powder increased with increasing precipitation temperature and may be related to the variation in ball-milling response observed among different H Area B-Line batches; calcined PuO 2 produced by Pu(III) reverse-strike precipitation was directly fabricated into a pellet without ball milling, slugging, or sharding. The pellet had good appearance with acceptable density and dimensional stability, and heat transfer measurements and calculations showed that the use of hollow aluminum sleeves in the plutonium fuel fabrication (PuFF) storage vault reduced the temperature of shipping cans to 170 0 C and will reduce the temperature at the center of pure plutonium oxide (PPO) spheres to 580 0 C

Overview of advanced technologies for stabilization of 238Pu-contaminated waste

International Nuclear Information System (INIS)

Ramsey, K.B.; Foltyn, E.M.; Heslop, J.M.

1998-02-01

This paper presents an overview of potential technologies for stabilization of 238 Pu-contaminated waste. Los Alamos National Laboratory (LANL) has processed 238 PuO 2 fuel into heat sources for space and terrestrial uses for the past several decades. The 88-year half-life of 238 Pu and thermal power of approximately 0.6 watts/gram make this isotope ideal for missions requiring many years of dependable service in inaccessible locations. However, the same characteristic which makes 238 Pu attractive for heat source applications, the high Curie content (17 Ci/gram versus 0.06 Ci/gram for 239 Pu ), makes disposal of 238 Pu-contaminated waste difficult. Specifically, the thermal load limit on drums destined for transport to the Waste Isolation Pilot Plant (WIPP), 0.23 gram per drum for combustible waste, is impossible to meet for nearly all 238 Pu-contaminated glovebox waste. Use of advanced waste treatment technologies including Molten Salt Oxidation (MSO) and aqueous chemical separation will eliminate the combustible matrix from 238 Pu-contaminated waste and recover kilogram quantities of 238 PuO 2 from the waste stream. A conceptual design of these advanced waste treatment technologies will be presented

Chemical thermodynamic representation of (U, Pu, Am)O2-x

International Nuclear Information System (INIS)

Osaka, Masahiko; Namekawa, Takashi; Kurosaki, Ken; Yamanaka, Shinsuke

2005-01-01

The oxygen potential isotherms of (U, Pu, Am)O 2-x were represented by a chemical thermodynamic model proposed by Lindemer et al. It was assumed in the present model that (U, Pu, Am)O 2-x consisted of the chemical species [UO 2 ], [PuO 2 ], [Pu 4/3 O 2 ], [AmO 2 ] and [Am 5/4 O 2 ] in a pseudo-quaternary system by treating the reduction rates of Pu and Am as identical; furthermore an interaction between [Am 5/4 O 2 ] and [UO 2 ] was introduced. The agreement between analytical and experimental isotherms was good, but the analytical values slightly overestimated the experimental values especially in the case of lower Am content. Adding an interaction between [Am 5/4 O 2 ] and [PuO 2 ] to the model resulted in a better representation

Determination of the neutron-induced fission cross section of {sup 242}Pu; Bestimmung des neutroneninduzierten Spaltquerschnitts von {sup 242}Pu

Energy Technology Data Exchange (ETDEWEB)

Koegler, Toni Joerg

2016-04-26

Neutron induced fission cross sections of actinides like the Pu-isotopes are of relevance for the development of nuclear transmutation technologies. For {sup 242}Pu, current uncertainties are of around 21%. Sensitivity studies show that the total uncertainty has to be reduced to below 5% to allow for reliable neutron physics simulations. This challenging task was performed at the neutron time-of-flight facility of the new German National Center for High Power Radiation Sources at HZDR, Dresden. Within the TRAKULA project, thin, large and homogeneous deposits of {sup 235}U and {sup 242}Pu have been produced successfully. Using two consecutively placed fission chambers allowed the determination of the neutron induced fission cross section of {sup 242}Pu relative to {sup 235}U. The areal density of the Plutonium targets was calculated using the measured spontaneous fission rate. Experimental results of the fast neutron induced fission of {sup 242}Pu acquired at nELBE will be presented and compared to recent experiments and evaluated data. Corrections addressing the neutron scattering are discussed by using results of different neutron transport simulations (Geant 4, MCNP 6 and FLUKA).

Vertical distribution of 239+240Pu-concentration and 240Pu/239Pu isotope ratio in sediment cores. Implications for the sources of plutonium in the Japan Sea

International Nuclear Information System (INIS)

Yamada, Masatoshi; Jian, Zheng

2005-01-01

The main sources in the environmental plutonium is due to nuclear explosions held during 1945 - 1980. The global fallout of plutonium is estimated to amount to 10.9 PBq, of which 6.6 PBq entering into the ocean. The Japan Sea is reported to be concentrated in plutonium in excess according to previous measurements. The present report aims to clarify the origin and transport path of plutonium in Japan Sea by measuring 240 Pu/ 239 Pu ratio in sedimenta cores with ICP-MS (Inductively Coupled Plasma Mass Spectrometry) which depends on the types of the nuclear reactor, nuclear fuels, reacting time, or the types of nuclear weapons concerned. As an example the 240 Pu/ 239 Pu ratio from the nuclear explosions in early 1960's is known to be 0.18, while that of 0.34-0.36 Bikini experiments in the Marshall Islands in early 1950's. After a detailed examination, the present authors propose that the plutonium from the explosion sites around the Marshall Islands was carried with an oceanic current to be deposited in the bed of the East-China Sea, from which a part of the plutonium was transported with the Black Stream to enter Japan Sea. (S. Ohno)

Study of phase equilibrium of Pu2O3-PuO2 system by the first-principles calculation and CALPHAD approach

International Nuclear Information System (INIS)

Minamoto, Satoshi; Kato, Masato; Konashi, Kenji

2010-01-01

A combination of a first-principles calculation, lattice dynamics and CALPHAD (CALculation of PHAse Diagrams) modeling is proven as a powerful tool so as to evaluate the Gibbs free energy and a phase equilibrium between compounds including large amount of vacancies. In this work, non-stoichiometric PuO 2-x (dioxide) and Pu 2 O 3 (sesquioxide) has been studied. An electron cohesive energy was evaluated from a first-principles calculations to estimate total energy of the compounds and a vacancy formation energy, and the theory of statistical mechanics was applied to evaluate enthalpy/entropy change due to oxygen vacancies for the non-stoichiometry of the PuO 2 (i.e. PuO 2-x ). Then a vacancy-vacancy interaction energy was determined by fitting to the experimental data of a quantity of non-stoichiometry of the PuO 2 compounds as a function of oxygen potentials at large deviation from stoichiometry. The resulting Gibbs free energy yields phase boundary between the phases with good agreement with to the experimental data.

Historical changes in ²³⁹Pu and ²⁴⁰Pu sources in sedimentary records in the East China Sea: Implications for provenance and transportation

DEFF Research Database (Denmark)

Wang, Jinlong; Baskaran, Mark; Hou, Xiaolin

2017-01-01

from 0.158 to 0.297 and were mostly higher than the mean global fallout value of 0.18. The 239,240Pu inventories in the ECS varied widely, from 2 to 807 Bqm−2, with the highest values commonly found in the coastal areas. In the Yangtze Estuary, the mean 239+240Pu activity concentration is close...... to the estimated value of the suspended material from the Yangtze River catchment (0.18 Bqkg−1), and the 240Pu/239Pu atom ratio was found to be ∼0.18, which indicates that the Yangtze River input is the dominant source of Pu for this area. The total annual Yangtze River input of 239+240Pu was estimated to be 2...

Determination of isotope fractionation effect using a double spike (242Pu+240Pu) during the mass spectrometric analysis of plutonium

International Nuclear Information System (INIS)

Chitambar, S.A.; Parab, A.R.; Khodade, P.S.; Jain, H.C.

1986-01-01

Isotope fractionation effect during the mass spectrometric analysis of plutonium has been investigated using a double spike ( 242 Pu+ 240 Pu) and the determination of concentration of plutonium in dissolver solution of irradiated fuel is reported. (author). 6 refs., 2 tables

Effect of Pu-rich agglomerate in MOX fuel on a lattice calculation

International Nuclear Information System (INIS)

Kawashima, Katsuyuki; Yamamoto, Toru; Namekawa, Masakazu

2007-01-01

The effect of Pu-rich agglomerates in U-Pu mixed oxide (MOX) fuel on a lattice calculation has been demonstrated. The Pu-rich agglomerate parameters are defined based on the measurement data of MIMAS-MOX and the focus is on the highly enriched MOX fuel in accordance with increased burnup resulting in a higher volume fraction of the Pu-rich agglomerates. The lattice calculations with a heterogeneous fuel model and a homogeneous fuel model are performed simulating the PWR 17x17 fuel assembly. The heterogeneous model individually treats the Pu-rich agglomerate and U-Pu matrix, whereas the homogeneous model homogenizes the compositions within the fuel pellet. A continuous-energy Monte Carlo burnup code, MVP-BURN, is used for burnup calculations up to 70 GWd/t. A statistical geometry model is applied in modeling a large number of Pu-rich agglomerates assuming that they are distributed randomly within the MOX fuel pellet. The calculated nuclear characteristics include k-inf, Pu isotopic compositions, power density and burnup of the Pu-rich agglomerates, as well as the pellet-averaged Pu compositions as a function of burnup. It is shown that the effect of Pu-rich agglomerates on the lattice calculation is negligibly small. (author)

The unrivalled expertise for Pu recycling

International Nuclear Information System (INIS)

Fournier, W.; Pouilloux, M.

1997-01-01

Relying on the outstanding performances of the reprocessing facilities and the growing fabrication facilities, the in-reactor Pu recycling program in France and in other European countries is steadily implemented and has reached full-scale industrial operation. The RCR strategy -Reprocessing, Conditioning and Recycling- developed by COGEMA is now a well proven industrial reality. In 1997, plutonium recycling through MOX fuel is a mature industry, with successful operational experience and large-scale fabrication plants. In this field, COGEMA is the main actor, on operating simultaneously three complete multidesign fuel production plants: MELOX plant (in Marcoule), CADARACHE plant and DESSEL plant (in Belgium). Present MOX production capacity available to COGEMA fits 175 tHM per year and will be extended to reach about 325 tHM in the year 2000, that will represent 75% of the total MOX fabrication capacity in Europe. The industrial mastery and the high production level in MOX production assured by high technology processes confers COGEMA an unrivalled expertise for Pu recycling. This allows COGEMA to be a major actor in Pu-based fuels in the coming second nuclear era with advanced fuel cycles. The paper depicts the steps of the progressive advance of COGEMA to reach the Pu recycling expertise. (author)

Determination of radionuclides {sup 90}Sr, {sup 239,240} Pu, {sup 238}Pu and {sup 241}Am in soil using methods of extraction chromatography and coprecipitation; Stanovenie radionuklidov {sup 90}Sr, {sup 239,240}Pu, : 2{sup 38}Pu a {sup 241}Am v pode vyuzivajuce metody extrakcnej chromatografie a spoluzrazania

Energy Technology Data Exchange (ETDEWEB)

Gardonova, V.; Dulanska, S.; Bilohuscin, J. [Univerzita Komenskeho, Prirodovedecka fakulta, Katedra jadrovej chemie, 84215 Bratislava (Slovakia)

2013-04-16

Ecosystems, which include soil and sediments, contain not only natural radionuclides but also radionuclides from deposits, mainly {sup 137}Cs, {sup 90}Sr and {alpha}-emitting radionuclides such as {sup 239,240}Pu, {sup 238}Pu and {sup 241}Am, that originate from global fallout and nuclear facilities leaks worldwide. The goal of the work was optimization of separation and determination of {sup 90}Sr, {sup 238}Pu, {sup 239,240}Pu and {sup 241}Am in soil from Slovak Republic. The newest methods were applied for separation of selected radionuclides based on coprecipitation with oxalic salts and extraction chromatography using selective commercial sorbents. (authors)

Fuel production for LWRs - MOX fuel aspects

International Nuclear Information System (INIS)

Deramaix, P.

2005-01-01

Plutonium recycling in Light Water Reactors is today an industrial reality. It is recycled in the form of (U, Pu)O 2 fuel pellets (MOX), fabricated to a large extent according to UO 2 technology and pellet design. The similarity of physical, chemical, and neutron properties of both fuels also allows MOX fuel to be burnt in nuclear plants originally designed to burn UO 2 . The industrial processes presently in use or planned are all based on a mechanical blending of UO 2 and PuO 2 powders. To obtain finely dispersed plutonium and to prevent high local concentration of plutonium, the feed materials are micronised. In the BNFL process, the whole (UO 2 , PuO 2 ) blend is micronised by attrition milling. According to the MIMAS process, developed by BELGONUCLEAIRE, a primary blend made of UO 2 containing about 30% PuO 2 is micronised in a ball mill, afterwards this primary blend is mechanically diluted in UO 2 to obtain the specified Pu content. After mixing, the (U, Pu)O 2 powder is pressed and the pellets are sintered. The sintering cover gas contains moisture and 5 v/o H 2 . Moisture increases the sintering process and the U-Pu interdiffusion. After sintering and grinding, the pellets are submitted to severe controls to verify conformity with customer specifications (fissile content, Pu distribution, surface condition, chemical purity, density, microstructure). (author)

Chemical properties of the predicted 32-electron systems PuSn{sub 12} and PuPb{sub 12}

Energy Technology Data Exchange (ETDEWEB)

Dognon, J.P. [CEA Saclay, UMR 3299 CEA/CNRS SIS2M, laboratoire de chimie de coordination des elements f, 91 - Gif-sur-Yvette (France); Clavaguera, C. [Laboratoire des mecanismes reactionnels, departement de chimie, Ecole polytechnique, CNRS, 91 - Palaiseau (France); Pyykko, P. [Department of Chemistry, University of Helsinki (Finland)

2010-06-15

The electronic structures, as well as spectroscopic and thermodynamic properties of the title PuM{sub 12} clusters, are considered at the density functional theory level. In both cases, a Pu{sup 2+} ion is encapsulated in an icosahedral, stanna- or plumbaspherene M{sub 12}{sup 2-} cage. As suggested before for M=Pb, both systems are reported to follow a 32-electron principle for the central atom. (authors)

Blended learning

DEFF Research Database (Denmark)

Dau, Susanne

2016-01-01

Blended Learning has been implemented, evaluated and researched for the last decades within different educational areas and levels. Blended learning has been coupled with different epistemological understandings and learning theories, but the fundamental character and dimensions of learning...... in blended learning are still insufficient. Moreover, blended learning is a misleading concept described as learning, despite the fact that it fundamentally is an instructional and didactic approach (Oliver & Trigwell, 2005) addressing the learning environment (Inglis, Palipoana, Trenhom & Ward, 2011......) instead of the learning processes behind. Much of the existing research within the field seems to miss this perspective. The consequence is a lack of acknowledgement of the driven forces behind the context and the instructional design limiting the knowledge foundation of learning in blended learning. Thus...

Study of phase equilibria in function of temperature in UO2-PuO2-Pu2O3 system for nuclear ceramics with high plutonium contents

International Nuclear Information System (INIS)

Truphemus, Thibaut

2013-01-01

In the UO 2 -PuO 2 -Pu 2 O 3 section, a monophasic (U 1-y ,Pu y )O 2-x domain is stable for y≤0,20 at 25 C and up to solid-liquid equilibrium. At higher Pu content, phase equilibria are more unclear with a phase separation process. The main objective of this work consisted in upgrading the representation of this system for 0,15≤y≤0,65 and 25≤T(C)≤1500. At 25 C, a miscibility gap composed by two different (U 1-y ,Pu y )O 2-x phases has been observed for y≤0,45, with one very closed to stoichiometric state (Oxygen/Metal=2) and one other very reduced. For the first time, a triphasic domain has been characterized at higher Pu contents, with two (U 1-y ,Pu y )O 2-x phases near y=0,45 and one (U 1-y ,Pu y ) 2 O 3 phase with a low U content inside. Concerning the study in function of temperature, we have demonstrated that phase separation temperature increase when Pu content grows. Several representations have been established. At 200 C, the representation is closed to that at 25 C. At 400 C, the phase separation have been specified at a lower Pu content than that of literature: y=0,35. At 600 C, our results have clarified the section, until then very unclear, with a phase separation appearing at y=0,60.The microstructural analysis has clearly demonstrated the significant impact of the phase separation on the material. Indeed many cracks have been observed in our samples, and quantity of these defects increases when Pu content grows. (author) [fr

Interception and retention of 238Pu deposition by orange trees

International Nuclear Information System (INIS)

Pinder, J.E. III; Adriano, D.C.; Ciravolo, T.G.; Doswell, A.C.; Yehling, D.M.

1987-01-01

Radioisotope thermoelectric generators (RTG) transform the heat produced during the alpha decay of 238 Pu into electrical energy for use by deep-space probes, such as the Voyager spacecraft, which have returned images and other data from Jupiter, Saturn and Uranus. Future missions involving RTGs may be launched aboard the space shuttle, and there is a remote possibility that an explosion of liquid-hydrogen and liquid-oxygen fuel could rupture the RTGs and disperse 238 Pu into the atmosphere over central Florida. Research was performed to determine the potential transport to man of atmospherically dispersed Pu via contaminated orange fruits. The results indicate that the major contamination of oranges would result from the interception and retention of 238 Pu deposition by fruits. The resulting surface contamination could enter human food chains through transfer to internal tissues during peeling or in the reconstituted juices and flavorings made from orange skins. The interception of 238 Pu deposition by fruits is especially important because the results indicate no measurable loss of Pu from fruit surfaces through time or with washing. Approximately 1% of the 238 Pu deposited onto an orange grove would be harvested in the year following deposition

Ion exchange nonwoven fabric chemical filter. 2

International Nuclear Information System (INIS)

Sekiguchi, Hideaki

2000-01-01

This report outlined the characteristics of EPIX filter and its complex with activated carbon to eliminate organic compounds from solvent. Elimination performance of this filter was determined using an ion chromatographic analyzer. EPIX filter showed high performance to eliminate trace amount of ionic compounds. The rate of elimination was both 99% or more for NH 3 and SO 2 in an early phase of filtration. Release of dust as well as impurities was significantly reduced by the use of EPIX filter. Gases once adsorbed on the filter were not released even at an elevated temperature of atmosphere. Combined use of non-woven fabrics was possible. For EPIX filter, there are three kinds; strong acid cation exchange filter and strong/weak basic anion filters. The weak basic anion filter has been applied to the conventional apparatus in wafer makers because the filter was very effective for selective boron trapping. When polyethyleneterephthalate was used as the base polymer, radical groups produced on the polymer were co-polymerized with monomer substances. The lifetime of filter was estimated on a base of gas concentration and wind velocity to determine the time to replace with a new one. Furthermore, the loss of pressure became less than a half when EPIX filter was used. (M.N.)

Chronic cigarette smoke exposure increases the pulmonary retention and radiation dose of 239Pu inhaled as 239PuO2 by F344 rats

International Nuclear Information System (INIS)

Finch, G.L.; Lundgren, D.L.; Barr, E.B.; Chen, B.T.; Griffith, W.C.; Hobbs, C.H.; Hoover, M.D.; Nikula, K.J.; Mauderly, J.L.

1998-01-01

As a portion of a study to examine how chronic cigarette smoke exposure might alter the risk of lung tumors from inhaled 239 PuO 2 in rats, the effects of smoke exposure on alpha-particle lung dosimetry over the life-span of exposed rats were determined. Male and female rats were exposed to inhaled 239 PuO 2 alone or in combination with cigarette smoke. Animals exposed to filtered air along served as controls for the smoke exposure. Whole-body exposure to mainstream smoke diluted to concentrations of either 100 or 250 mg total particulate matter m -3 began at 6 wk of age and continued for 6 h d -1 , 5 d wk -1 , for 30 mo. A single, pernasal, acute exposure to 239 PuO 2 was given to all rats at 12 wk of age. Exposure to cigarette smoke caused decreased body weight gains in a concentration dependent manner. Lung-to-body weight ratios were increased in smoke-exposed rats. Rats exposed to cigarette smoke before the 239 PuO 2 exposure deposited less 239 Pu in the lung than did controls. Except for male rats exposed to LCS, exposure to smoke retarded the clearance of 239 Pu from the lung compared to control rats through study termination at 870 d after 239 PuO 2 exposure. Radiation doses to lungs were calculated by sex and by exposure group for rats on study for at least 360 d using modeled body weight changes, lung-to-body weight ratios, and standard dosimetric calculations. For both sexes, estimated lifetime radiation doses from the time of 239 PuO 2 exposure to death were 3.8 Gy, 4.4 Gy, or 6.7 Gy for the control, LCS, or HCS exposure groups, respectively. Assuming an approximately linear dose-response relationship between radiation dose and lung neoplasm incidence, approximate increases of 20% or 80% in tumor incidence over controls would be expected in rats exposed to 239 PuO 2 and LCS or 239 PuO 2 and HCS, respectively

Contribution to the study of U-Ti and U-Pu-Ti carbides

International Nuclear Information System (INIS)

Milet, C.A.

1968-01-01

After having discussed the reasons to use (U,Pu) carbides as fast reactor fuel, we examine the influence of the addition of titanium to these carbides. A preliminary study has been done on the system of U-C-Ti and some properties have been measured such as: density, thermal expansion, electrical resistivity, atmospheric corrosion and compatibility with stainless steel. The systems U-Pu-C-Ti (Pu/U + Pu equal to 15 per cent) and U-C-Ti have been found to be very similar. There exists a two phases region (U,Pu)C + TiC, an eutectic between (U,Pu)C and TiC for approximately 15 at %. The solubilities of U + Pu in TiC and of Ti in (U,Pu)C is less than 1 % at. The addition of titanium does not markedly change thermal expansion coefficients of (U,Pu)C. However the resistance to atmospheric corrosion and compatibility with stainless steel is improved. Thermal conductivity, calculated from electrical resistivity, has increased. On the other side, the density of fissile material is lowered. The combination of (U,Pu)C + TiC seems to be the most promising alloy for application as nuclear fuel. (author) [fr

238Pu fuel form processes. Final report, January-September 1983

International Nuclear Information System (INIS)

Mosley, W.C.; Taylor, D.H.

1983-01-01

Progress is reported on the following: analytical studies of weld-quench cracking in DOP-26 iridium alloy, iridium/ 238 PuO 2 compatibility test, surface area measurements of 238 PuO 2 using the Blaine air permeability apparatus, and helium release from 238 PuO 2

Redox thermodynamic data of plutonium in acidic and carbonate media. Pu(V) stability

International Nuclear Information System (INIS)

Capdevila, H.

1992-01-01

Pu redox equilibria are studied in acidic and carbonate media in this thesis, to build a thermodynamic data bank consistent with the TDB (NEA-OECD) one and in connection with radioactive waste disposal programs. Literature is discussed and reinterpreted. The experimental method is tested with Uranium preliminary measurements. The reversible redox potentials (PuO 2 + and Pu 4+ /Pu 3+ ) are measured using the cyclic voltametric technique in perchloric media at several ionic strengths (from 0.5 to 3M) and temperatures (from 0 to 70 deg C). The Specific Interaction Theory (SIT) is used to measured activity coefficients and to extrapolate data to the standard conditions. The potentials variations versus temperature are linear in first approximation: the entropy changes are found constant from 0 to 70 deg C and the heat capacity changes are within uncertainties. The standard constant of PuO 2 + disproportionation into PuO 2 2+ and Pu 3+ is deduced from spectrophotometric measurements performed in perchloric media around pH=1 where Pu 4+ hydrolysis is discussed. The Pu non-reversible standard potentials (PuO 2 2+ /Pu 4+ for instance) are then calculated and validated with a spectrophotometric study of Pu 4+ formation from PuO 2 2+ and Pu 3+ in a 1M perchloric acidic solution. The Pu(VI/V) redox potential, activity coefficients and entropies are measured using the same technique in concentrated carbonate media. The limiting complex standard formation constants and the redox potential shifts (between acidic and carbonate media) are then discussed among the U, Np, Pu and Am actinides. A spectrophotometric study of the equilibrium between the complexes with 5 and 4 carbonate ligands allowed to measure Pu(IV) limiting complex stability at several ionic strengths. (author). 26 tabs., 46 figs., 95 refs

Measurement of the ${240}$Pu(n,f) reaction cross-section

CERN Multimedia

Following proposal CERN-INTC-2010-042 / INTC-P-280 (“Measurement of the fission cross-section of $^{240}$Pu and $^{242}$Pu at CERN’s n_TOF Facility”), the parallel measurement of the $^{240}$Pu(n,f) and $^{242}$Pu(n,f) reaction cross-sections was carried out at n_TOF EAR-1. While the $^{242}$Pu measurement was successful, unexpected sample-induced damage to the detectors caused by the high α-activity of the 240Pu samples resulted in a deterioration of the detector performance over the data taking period of several months, which compromised the measurement. This obstacle can be eliminated by performing the measurement in EAR-2, where the higher neutron flux will allow collecting data in a much shorter time, thus preventing the degradation of the detectors. In addition to this obvious advantage, the measurement would also benefit from the stronger suppression of the sample-induced α-background, due to the shorter times-of-flight involved.

Distinguishing Pu Metal from Pu Oxide and Determining alpha-ratio using Fast Neutron Counting

Energy Technology Data Exchange (ETDEWEB)

Verbeke, J. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chapline, G. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Nakae, L. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Prasad, M. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sheets, S. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Snyderman, N. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-01-07

We describe a new method for determining the ratio of the rate of (α, n) source neutrons to the rate of spontaneous fission neutrons, the so called α-ratio. This method is made possible by fast neutron counting with liquid scintillator detectors, which can determine the shape of the fast neutron spectrum. The method utilizes the spectral difference between fission spectrum neutrons from Pu metal and the spectrum of (α, n) neutrons from PuO₂. Our method is a generalization of the Cifarelli-Hage method for determining k_eff for fissile assemblies, and also simultaneously determines k_eff along with the α-ratio.

Simultaneous measurement of {sup 239}Pu, {sup 240}Pu, {sup 241}Pu, and {sup 242}Pu by high resolution inductively coupled plasma mass spectrometer (HR ICP-MS) in marine sediments; Mesure des isotopes du plutonium des sediments marins par spectrometrie de masse a plasma couple inductivement haute resolution (HR ICP-MS)

Energy Technology Data Exchange (ETDEWEB)

Bruneau, F

1999-07-01

Transuranics elements are of particular interest in radioecological studies because of their radiotoxicity and their potential use to decipher source fingerprints and transport processes. The simultaneous measurement of {sup 239}Pu, {sup 240}Pu, {sup 241}Pu, and {sup 242}Pu in environmental samples requires a specific chemical procedure. This work deals with an analytical procedure which yields a very high grade of purification of Pu suitable for ultra low level detection by HR ICP-MS, from marine sediments. After the elimination of major elements (Fe, Al, Mg...) by a first chromatographic separation, a new device of purification by solvent extraction and concentration by a second chromatographic separation is used to obtain a concentrated and high purified solution of plutonium. The chemical procedure have been validated on IAEA certified sediment samples and on sediment samples collected in the roads of Cherbourg which had been previously analysed by other techniques (a spectrometry and thermo-ionisation mass spectrometer). (author)

[Acupuncture messenger--Pu Xiang-cheng].

Science.gov (United States)

Du, Huai-bin; Liang, Fan-rong

2011-06-01

PU Xiang-cheng is the eminent acupuncture master in modern history of China. He studied diligently in early years and devoted his life to the cause of acupuncture practice and education in Chinese medicine. Combination of acupuncture and herbal medicine, coordination of acupuncture and moxibustion, unique application of acupoints, flexible combination of acupoints and focusing on needling techniques are the essence of his academic thoughts. The life of PU Xiang-cheng, the acupuncture master, and his major academic thoughts are described in this paper, so as to commemorate his contributions to acupuncture theory, practice and promotions.

Nutritional value of ramie and it sruminal degradability%苎麻营养成分分析及瘤胃降解特性研究

Institute of Scientific and Technical Information of China (English)

魏金涛; 杨雪海; 严念东; 熊常财; 汪红武; 陈芳; 张乃锋; 刁其玉

2017-01-01

The aim of this study was to investigate the nutrient components and ruminal degradability character-istics of ramie.Common nutrition components,amino acids composition,and anti-nutrient (e.g.,tannin) contents were determined for seven ramie samples containing different proportions of stubble,and the ruminal degradability was estimated using three male Boer goats fitted with permanent rumen fistula.The average crude protein (CP)content of the seven stubble samples was 19.57%.The CP content decreased with increas-ing proportions of stubble,but the CP content in sample 7 ,which had the highest proportion of stubble,was slightly higher than that in sample 6 ,which had a slightly lower proportion of stubble.The average total amino acids content was 16.40%,accounting for 83.80% of CP.The average Lys and Thr contents were 0.84% and 0.82%,respectively.The average content of tannin,the main anti-nutrient in ramie,was 0.67%.The rumi-nal degradability of ramie dry matter,CP,organic matter,neutral detergent fiber,and acid detergent fiber in-creased with longer digestion time;the effective degradability of these nutrients was 47.00%,35.53%, 44.29%,57.68% and 38.59%,respectively.In conclusion,ramie has a high protein content,high-quality CP,and high rumianl degradability of some nutrients.Therefore,it is a good forage for ruminants.%为系统的研究苎麻的营养价值及其在山羊瘤胃中的降解特性,利用化学分析等方法检测了7个茬次苎麻的粗蛋白(CP)、氨基酸(AA)组成、中性洗涤纤维(NDF)、酸性洗涤纤维(ADF)等营养成分、单宁等抗营养成分的含量,并采用3只装有永久瘤胃瘘管的波尔山羊为试验动物,对苎麻的部分营养成分的降解率和降解参数进行测定.结果表明,7个茬次苎麻的CP含量均较高且品质较好,CP平均值达到了19.57%,而且呈现出随着茬次的增加,CP含量有所下降的趋势,但是第7茬和第6茬相比CP含量略有升高.AA总和平均值达到了16.40%,�

Supporting School Leaders in Blended Learning with Blended Learning

Science.gov (United States)

Acree, Lauren; Gibson, Theresa; Mangum, Nancy; Wolf, Mary Ann; Kellogg, Shaun; Branon, Suzanne

2017-01-01

This study provides a mixed-methods case-study design evaluation of the Leadership in Blended Learning (LBL) program. The LBL program uses blended approaches, including face-to-face and online, to prepare school leaders to implement blended learning initiatives in their schools. This evaluation found that the program designers effectively…

Conductivity and touch-sensor application for atomic layer deposition ZnO and Al:ZnO on nylon nonwoven fiber mats

International Nuclear Information System (INIS)

Sweet, William J.; Oldham, Christopher J.; Parsons, Gregory N.

2015-01-01

Flexible electronics and wearable technology represent a novel and growing market for next generation devices. In this work, the authors deposit conductive zinc oxide films by atomic layer deposition onto nylon-6 nonwoven fiber mats and spun-cast films, and quantify the impact that deposition temperature, coating thickness, and aluminum doping have on the conductivity of the coated substrates. The authors produce aluminum doped zinc oxide (AZO) coated fibers with conductivity of 230 S/cm, which is ∼6× more conductive than ZnO coated fibers. Furthermore, the authors demonstrate AZO coated fibers maintain 62% of their conductivity after being bent around a 3 mm radius cylinder. As an example application, the authors fabricate an “all-fiber” pressure sensor using AZO coated nylon-6 electrodes. The sensor signal scales exponentially under small applied force (<50 g/cm 2 ), yielding a ∼10 6 × current change under 200 g/cm 2 . This lightweight, flexible, and breathable touch/force sensor could function, for example, as an electronically active nonwoven for personal or engineered system analysis and diagnostics

Cyclic stress-strain behavior of polymeric nonwoven structures for the use as artificial leaflet material for transcatheter heart valve prostheses

Directory of Open Access Journals (Sweden)

Arbeiter Daniela

2017-09-01

Full Text Available Xenogenic leaflet material, bovine and porcine pericardium, is widely used for the fabrication of surgically implanted and transcatheter heart valve prostheses. As a biological material, long term durability of pericardium is limited due to calcification, degeneration and homogeneity. Therefore, polymeric materials represent a promising approach for a next generation of artificial heart valve leaflets with improved durability. Within the current study we analyzed the mechanical performance of polymeric structures based on elastomeric materials. Polymeric cast films were prepared and nonwovens were manufactured in an electrospinning process. Analysis of cyclic stress-strain behavior was performed, using a universal testing machine. The uniaxial cyclic tensile experiments of the elastomeric samples yielded a non-linear elastic response due to viscoelastic behavior with hysteresis. Equilibrium of stress-strain curves was found after a specific number of cycles, for cast films and nonwovens, respectively. In conclusion, preconditioning was found obligatory for the evaluation of the mechanical performance of polymeric materials for the use as artificial leaflet material for heart valve prostheses.

Roles sociales de la sociedad contemporánea en la película 'Multiplicity' de Harold Ramis

Directory of Open Access Journals (Sweden)

Raquel Fernández Cobo

2015-10-01

Full Text Available Multiplicity (2010, dirigida por Harold Ramis, plasma en pantalla a través del motivo del doble los elementos que constituyen la crisis del sujeto y que representan al individuo bajo el signo de la disipación. Mediante un análisis temático y discursivo del motivo del doble examinamos cómo el protagonista, al intentar llevar a cabo la totalidad de los roles sociales, se ve abocada a las contradicciones más agudas de la sociedad, manifestadas, sobre todo, a nivel del cuerpo, tanto en el manifiesto simbolismo del motivo del doble como en el “terror biológico” que de forma absolutamente irónica y humorística se representa en el último clon del protagonista.

Redefining design criteria for Pu-238 gloveboxes

International Nuclear Information System (INIS)

Acosta, S.V.

1998-01-01

Enclosures for confinement of special nuclear materials (SNM) have evolved into the design of gloveboxes. During the early stages of glovebox technology, established practices and process operation requirements defined design criteria. Proven boxes that performed and met or exceeded process requirements in one group or area, often could not be duplicated in other areas or processes, and till achieve the same success. Changes in materials, fabrication and installation methods often only met immediate design criteria. Standardization of design criteria took a big step during creation of ''Special-Nuclear Materials R and D Laboratory Project, Glovebox standards''. The standards defined design criteria for every type of process equipment in its most general form. Los Alamos National Laboratory (LANL) then and now has had great success with Pu-238 processing. However with ever changing Environment Safety and Health (ES and H) requirements and Ta-55 Facility Configuration Management, current design criteria are forced to explore alternative methods of glovebox design fabrication and installation. Pu-238 fuel processing operations in the Power Source Technologies Group have pushed the limitations of current design criteria. More than half of Pu-238 gloveboxes are being retrofitted or replaced to perform the specific fuel process operations. Pu-238 glovebox design criteria are headed toward process designed single use glovebox and supporting line gloveboxes. Gloveboxes that will house equipment and processes will support TA-55 Pu-238 fuel processing needs into the next century and extend glovebox expected design life

Blended Learning

OpenAIRE

Bauerová, Andrea

2013-01-01

This thesis is focused on a new approach of education called blended learning. The history and developement of Blended Learning is described in the first part. Then the methods and tools of Blended Learning are evaluated and compared to the traditional methods of education. At the final part an efficient developement of the educational programs is emphasized.

Phase equilibrium of PuO{sub 2-x} - Pu{sub 2}O{sub 3} based on first-principles calculations and configurational entropy change

Energy Technology Data Exchange (ETDEWEB)

Minamoto, Satoshi, E-mail: satoshi.minamoto@ctc-g.co.jp [ITOCHU Techno-Solutions Corporation, Kasumigaseki, 2-5, Kasumigaseki 3-chome, Chiyoda-ku, Tokyo 100-6080 (Japan); Kato, Masato [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki (Japan); Konashi, Kenji [Institute for Materials Research, Tohoku University, Oarai-chou, Ibaraki (Japan)

2011-05-31

Combination of an oxygen vacancy formation energy calculated using first-principles approach and the configurational entropy change treated within the framework of statistical mechanics gives an expression of the Gibbs free energy at large deviation from stoichiometry of plutonium oxide PuO{sub 2}. An oxygen vacancy formation energy 4.20 eV derived from our previously first-principles calculation was used to evaluate the Gibbs free energy change due to oxygen vacancies in the crystal. The oxygen partial pressures then can be evaluated from the change of the free energy with two fitting parameters (a vacancy-vacancy interaction energy and vibration entropy change due to induced vacancies). Derived thermodynamic expression for the free energy based on the SGTE thermodynamic data for the stoichiometric PuO{sub 2} and the Pu{sub 2}O{sub 3} compounds was further incorporated into the CALPHAD modeling, then phase equilibrium between the stoichiometric Pu{sub 2}O{sub 3} and non-stoichiometric PuO{sub 2-x} were reproduced.

Investigation on U - O - Na, Pu - O - Na and U,Pu - O - Na phase diagrams

International Nuclear Information System (INIS)

Pillon, S.

1989-03-01

The thermochemical interaction between the nuclear fuel (uranium and plutonium mixed oxides) and the sodium has been investigated and particularly the three phase diagrams: U - O - Na; Pu - O - Na; U,Pu - O - Na. High temperature neutron diffraction, microcalorimetry and powder X-ray diffraction were used for the characterization of the compounds synthetized. This study allowed to complete the knowledge about each of these diagrams and to measure some physical and thermal properties on the compounds. The limits on the modelization of the fuel-sodium interaction are discussed from the results of the UO 2 - Na reaction [fr

Analytical description of transfer of Pu-239 in undisturbed soil

Energy Technology Data Exchange (ETDEWEB)

Tianshan, Ren; Linsalata, P; Cohen, N

1986-04-01

The paper reports on an analytical model for describing the horizontal and down-ward transfer of /sup 239/Pu in undisturbed soil based on observed data. The model has been developed to predict how the depth distribution of /sup 239/Pu in soil would change with time. This information is essential for estimation of the quantities of /sup 239/Pu that have entered surface water body via erosion and runoff processes and for estimation of the long-term impact of /sup 239/Pu isice the commencement of nuclear fallout deposition.

Pb-210 and Pu-239,240 in nearshore Gulf of Mexico sediments

International Nuclear Information System (INIS)

Rotter, R.J.

1985-05-01

Pb-210, Ra-226, and Pu-239,240 activities were measured in nearshore Gulf of Mexico sediments. Sediment cores were collected from the Mississippi delta, and the western Gulf of Mexico shelf. Mississippi delta cores which exhibit significantly higher sedimentation rates show larger inventories of Pb-210. The measured Pu levels from the western shelf are lower than from the delta at comparable depths. In three of the western shelf cores, the observed Pu inventory is considerably less than predicted from atmospheric flux. Therefore, Pu is not being removed to the sediment, or is being released following deposition. A key difference between these isotopes is that Pu exists in a less particle-reactive state. The ratio of excess Pb-210 to Pu levels increases with water depth in the delta and the western shelf. Water depth acts as an integrator of depth-sensitive processes. Pu scavenging is more sensitive to these processes. A sub-surface Pu maximum has been observed. Excess Pb-210 and Pu levels correlate well with sedimentation rates. This suggests that particle flux is important in removal of Pb-210 and Pu to the sediment. The flux of Mn out of the sediment is correlated with inventory data, suggesting that redox cycling of Mn may play a role in increasing Pb-210 and Pu sediment inventories. It is unclear whether the effects of increased sedimentation rates and increased Mn fluxes can be evaluated independently. Mixing of surface sediment correlates with inventory data. Increased sediment mixing allows for additional scavenging of Pb-210 and Pu from overlying waters. Mixing of sediment at depths below the mixed surface layer may play a role in increasing sediment inventories of Pb-210 and Pu

Electrochemical investigations of Pu(IV)/Pu(III) redox reaction using graphene modified glassy carbon electrodes and a comparison to the performance of SWCNTs modified glassy carbon electrodes

International Nuclear Information System (INIS)

Gupta, Ruma; Gamare, Jayashree; Sharma, Manoj K.; Kamat, J.V.

2016-01-01

Highlights: • First report of aqueous electrochemistry of Plutonium on graphene modified electrode. • Graphene is best electrocatalytic material for Pu(IV)/Pu(III) redox couple among the reported modifiers viz. reduced graphene oxide (rGO) and SWCNT’s. • The electrochemical reversibility of Pu(IV)/Pu(III) redox couple improves significantly on graphene modified electrode compared to previously reported rGO & SWCNTs modified electrodes • Donnan interaction between plutonium species and graphene surface offers a possibility for designing a highly sensitive sensor for plutonium • Graphene modified electrode shows higher sensitivity for the determination of plutonium compared to glassy carbon and single walled carbon nanotube modified electrode - Abstract: The work reported in this paper demonstrates for the first time that graphene modified glassy carbon electrode (Gr/GC) show remarkable electrocatalysis towards Pu(IV)/Pu(III) redox reaction and the results were compared with that of single-walled carbon nanotubes modified GC (SWCNTs/GC) and glassy carbon (GC) electrodes. Graphene catalyzes the exchange of current of the Pu(IV)/Pu(III) couple by reducing both the anodic and cathodic overpotentials. The Gr/GC electrode shows higher peak currents (i p ) and smaller peak potential separation (ΔE p ) values than the SWCNTs/GC and GC electrodes. The heterogeneous electron transfer rate constants (k s ), charge transfer coefficients (α) and the diffusion coefficients (D) involved in the electrocatalytic redox reaction were determined. Our observations show that graphene is best electrocatalytic material among both the SWCNTs and GC to study Pu(IV)/Pu(III) redox reaction.

First-principles elastic constants and phonons of delta-Pu

DEFF Research Database (Denmark)

Söderlind, P.; Landa, A.; Sadigh, B.

2004-01-01

Elastic constants and zone-boundary phonons of delta-plutonium have been calculated within the density-functional theory. The paramagnetic state of delta-Pu is modeled by disordered magnetism utilizing either the disordered local moment or the special quasirandom structure techniques. The anomalo......Elastic constants and zone-boundary phonons of delta-plutonium have been calculated within the density-functional theory. The paramagnetic state of delta-Pu is modeled by disordered magnetism utilizing either the disordered local moment or the special quasirandom structure techniques....... The anomalously soft C-' as well as a large anisotropy ratio (C-44/C-') of delta-Pu is reproduced by this theoretical model. Also the recently measured phonons for delta-Pu compare relatively well with their theoretical counterpart at the zone boundaries....

Transplacental absorption of 238Pu in rats and guinea pigs

International Nuclear Information System (INIS)

Sullivan, M.F.

1980-01-01

Pregnant rats and guinea pigs were injected intravenously with 238 Pu citrate to determine if the potential for in utero accumulation of 238 Pu by these two species is related to the stage of development at which immunity is gained. Although guinea pigs retained more 238 Pu after birth than rats, the difference was not significant

Detection of Pu in Pacific Ocean water with AMS related to the Fukushima accident

Energy Technology Data Exchange (ETDEWEB)

Hain, Karin; Faestermann, Thomas; Fimiani, Leticia; Guzman, Jose Manuel; Korschinek, Gunther; Kortmann, Florian; Lierse v Gostomski, Christoph; Ludwig, Peter [TUM (Germany); Golser, Robin; Steier, Peter [Universitaet Wien (Austria); Yamada, Masatoshi [Hirosaki University (Japan)

2016-07-01

The concentration of plutonium (Pu) and its isotopic ratios were determined by accelerator mass spectrometry (AMS) in Pacific Ocean water samples. The isotopic ratios {sup 240}Pu/{sup 239}Pu and {sup 241}Pu/{sup 239}Pu can be used to identify a possible release of Pu into the ocean by the Fukushima accident. {sup 241}Pu from fallout of nuclear weapon testings has already significantly decayed. {sup 241}Am, the daughter nuclide of {sup 241}Pu, causes isobaric background on {sup 241}Pu in mass-spectrometric measurements. Therefore, Am and Pu had to be separated chemically using extraction chromatography. The method was verified by analyzing certified reference material. 12 sea water samples, collected at different depths, were prepared at the Radiochemie Muenchen. The concentration of Pu was measured with AMS at the Maier-Leibnitz-Laboratory in Munich and the Vienna Environmental Research Laboratory (VERA). After a short motivation related to the Fukushima accident, the chemical separation method will be presented. Preliminary results of the distribution of Pu in ocean water will be discussed.

Procedure for plutonium determination using Pu(VI) spectra

International Nuclear Information System (INIS)

Walker, L.F.; Temer, D.J.; Jackson, D.D.

1996-01-01

This document describes a simple spectrophotometric method for determining total plutonium in nitric acid solutions based on the spectrum of Pu(VI). Plutonium samples in nitric acid are oxidized to Pu(VI) with Ce(IV) and the net absorbance at the 830 nm peak is measured

Determination of Pu Oxidation states in the HCl Media Using with UV-Visible Absorption Spectroscopic Techniques

International Nuclear Information System (INIS)

Lee, Myung Ho; Suh, Mu Yeol; Park, Kyoung Kyun; Park, Yeong Jae; Kim, Won Ho

2006-01-01

The spectroscopic characteristics of Pu (III, IV, V, VI) in the HCl media were investigated by measuring Pu oxidation states using a UV-Vis-NIR spectrophotometer (400-1200 nm) after adjusting Pu oxidation states with oxidation/reduction reagents. Pu in stock solution was reduced to Pu(III) with NH 2 OH · HCl, and oxidized to Pu(IV) and Pu(VI) with NaNO 2 and HCIO 4 , respectively. Also, Pu(V) was adjusted in the Pu(VI) solution with NH 2 OH · HCl. The major absorption peaks of Pu (IV) and Pu(III) were measured in the 470 nm and 600 nm, respectively. The major absorption peaks of Pu (VI) and Pu(V) were measured in the 830 nm and 1135 nm, respectively. There was not found to be significant changes of UV-V is absorption spectra for Pu(III), Pu(IV) and Pu(VI) with aging time, except that an unstable Pu(V) immediately reduced to Pu(III).

Influence of the goethite (α-FeOOH) surface on the stability of distorted PuO{sub 2} and PuO{sub 2-x} phases

Energy Technology Data Exchange (ETDEWEB)

Taylor, Sandra D.; Becker, Udo [Univ. of Michigan, Ann Arbor, MI (United States). Dept. of Earth and Environmental Sciences; Powell, Brian A. [Clemson Univ., Anderson, SC (United States). Environmental Engineering and Earth Science Dept.

2016-07-01

Experiments by [Powell, B. A., Dai, Z. R., Zavarin, M., Zhao, P. H., Kersting, A. B.: Stabilization of plutonium nano-colloids by epitaxial distortion on mineral surfaces. Environ. Sci. Technol. 45, 2698 (2011).] deduced the heteroepitaxial growth of a bcc Pu{sub 4}O{sub 7} phase when sorbed onto goethite from d-spacing measurements obtained from selected-area electron diffraction (SAED) patterns. The structural and/or chemical modification of Pu(IV) oxide (PO) nanocolloids upon sorption to goethite, in turn, affects colloidal-transport of Pu in the subsurface. In this study, molecular simulations were applied to investigate mechanisms affecting the formation of non-fcc PO phases and to understand the influence of goethite in stabilizing the non-fcc PO phase. Analyses of the structure, chemistry, and formation energetics for several bulk PuO{sub 2} and PuO{sub 2-x} phases, using ab initio methods, show that the formation of a non-fcc PO can occur from the lattice distortion (LD) of fcc PuO{sub 2} upon sorption and formation of a PO-goethite interface. To strain and non-uniformly distort the PuO{sub 2} lattice to match that of the goethite substrate at ambient conditions would require 88 kJ/mol Pu{sub 4}O{sub 8}. The formation of a hypostoichiometric PuO{sub 2-x} phase, such as the experimentally-deduced bcc, Ia anti 3 Pu{sub 4}O{sub 7} phase, requires more O-poor conditions and/or high energetic inputs (> +365 kJ/mol Pu{sub 4}O{sub 7} at O-rich conditions). Empirical methods were also applied to study the effect of lattice distortion on sorption energetics and adsorbate particle growth using simple heterointerfaces between cubic salts, where KCl clusters (notated as KCl{sub LD}) of varying size and lattice mismatch (LM) were sorbed to a NaCl cluster. When the lattice of a KCl{sub LD} cluster has <15% LM with that of a NaCl substrate, the sorption of KCl{sub LD} onto NaCl is exothermic (<-80 kJ/mol) and the KCl{sub LD} cluster can reach sizes of ∝2-5 nm on the Na

Measurements Conducted on an Unknown Object Labeled Pu-239

International Nuclear Information System (INIS)

Hoteling, Nathan

2013-01-01

Measurements were carried out on 12 November 2013 to determine whether Pu-239 was present on an object discovered in a plastic bag with label ''Pu-239 6 uCi''. Following initial survey measurements to verify that the object was not leaking or contaminated, spectra were collected with a High Purity Germanium (HPGe) detector with object positioned in two different configurations. Analysis of the spectra did not yield any direct evidence of Pu-239. From the measured spectra, minimum detectable activity (MDA) was determined to be approximately 2 uCi for the gamma ray measurements. Although there was no direct evidence of Pu-239, a peak at 60 keV characteristic of Am-241 decay was observed. Since it is very likely that Am-241 would be present in aged plutonium samples, this was interpreted as indirect evidence for the presence of plutonium on the object. Analysis of this peak led to an estimated Pu-239 activity of 0.02-0.04 uCi, or <1x10 -6 grams.

Anticoagulant and antimicrobial finishing of non-woven polypropylene textiles

International Nuclear Information System (INIS)

Degoutin, S; Jimenez, M; Casetta, M; Bellayer, S; Chai, F; Blanchemain, N; Neut, C; Kacem, I; Traisnel, M; Martel, B

2012-01-01

The aim of this work is to prepare non-woven polypropylene (PP) textile functionalized with bioactive molecules in order to improve its anticoagulation and antibacterial properties. This paper describes the optimization of the grafting process of acrylic acid (AA) on low-pressure cold-plasma pre-activated PP, the characterization of the modified substrates and the effect of these modifications on the in vitro biological response towards cells. Then, the immobilization of gentamicin (aminoglycoside antibiotic) and heparin (anticoagulation agent) has been carried out on the grafted samples by either ionic interactions or covalent linkages. Their bioactivity has been investigated and related to the nature of their interactions with the substrate. For gentamicin-immobilized AA-grafted samples, an inhibition radius and a reduction of 99% of the adhesion of Escherichia coli have been observed when gentamicin was linked by ionic interactions, allowing the release of the antibiotic. By contrast, for heparin-immobilized AA-grafted PP samples, a strong increase of the anticoagulant effect up to 35 min has been highlighted when heparin was covalently bonded on the substrate, by contact with the blood drop. (paper)

Preparation of a non-woven poly(ε-caprolactone) fabric with partially embedded apatite surface for bone tissue engineering applications by partial surface melting of poly(ε-caprolactone) fibers.

Science.gov (United States)

Kim, In Ae; Rhee, Sang-Hoon

2017-07-01

This article describes a novel method for the preparation of a biodegradable non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface designed for application as a scaffold material for bone tissue engineering. The non-woven poly(ε-caprolactone) fabric was generated by the electro-spinning technique and then apatite was coated in simulated body fluid after coating the PVA solution containing CaCl 2 ·2H 2 O. The apatite crystals were partially embedded or fully embedded into the thermoplastic poly(ε-caprolactone) fibers by controlling the degree of poly(ε-caprolactone) fiber surface melting in a convection oven. Identical apatite-coated poly(ε-caprolactone) fabric that did not undergo heat-treatment was used as a control. The features of the embedded apatite crystals were evaluated by FE-SEM, AFM, EDS, and XRD. The adhesion strengths of the coated apatite layers and the tensile strengths of the apatite coated fabrics with and without heat-treatment were assessed by the tape-test and a universal testing machine, respectively. The degree of water absorbance was assessed by adding a DMEM droplet onto the fabrics. Moreover, cell penetrability was assessed by seeding preosteoblastic MC3T3-E1 cells onto the fabrics and observing the degrees of cell penetration after 1 and 4 weeks by staining nuclei with DAPI. The non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface showed good water absorbance, cell penetrability, higher apatite adhesion strength, and higher tensile strength compared with the control fabric. These results show that the non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface is a potential candidate scaffold for bone tissue engineering due to its strong apatite adhesion strength and excellent cell penetrability. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1973-1983, 2017. © 2017 Wiley Periodicals, Inc.

High-240Pu fuel worth in the Fast Test Reactor Engineering Mockup

International Nuclear Information System (INIS)

Daughtry, J.W.; Dobbin, K.D.

1975-01-01

Reactivity effects associated with the replacement of low- 240 Pu fuel with high- 240 Pu fuel were calculated and compared to measurements made in the FTR Engineering Mockup Critical (EMC). When the Pu and U isotopic compositions were changed in a way that increased the amounts of 240 Pu and 241 Pu and reduced the amounts of 239 Pu and 238 U while conserving total fissile mass and total fertile mass, the reactivity effect was positive. Calculation-to-experiment bias factors were obtained for this type of change and for the replacement of Fe 2 O 3 with U 3 O 8 in subassembly-size zones of the EMC. The k/sub e/--k/sub c/ bias decreased when high- 240 Pu fuel was introduced and increased when Fe 2 O 3 was replaced with U 3 O 8 . When the two changes were combined, their effects on the k/sub e/ --k/sub c/ bias tended to cancel out. The work described is related to plans for the utilization of light water reactor discharge Pu in the FTR

Routine radiochemical method for the determination of 90Sr, 238Pu, 239+240Pu, 241Am and 244Cm in environmental samples

International Nuclear Information System (INIS)

Ageyev, V.A.; Sajeniouk, A.D.

2005-01-01

Routine analytical procedures have been developed for the reliable simultaneous determination of 90 Sr, 238 Pu, 239+240 Pu, 241 Am and 242-244 Cm, Chernobyl derived radioisotopes and fallout after nuclear weapon tests in a wide range of environmental samples: soil (100-200 g), sediments, aerosols, water and vegetation. This procedure has been applied to thousands of soil and sediment samples and hundreds of biological and water samples taken in the exclusive zone of Chernobyl NPP and different regions of Ukraine from 1989 to the present. After the sample has been properly prepared and isotopic tracers added, plutonium, americium and curium are precipitated with calcium oxalate and then lanthanum fluoride. Plutonium is separated from americium and curium by anion-exchange. Americium and curium are separated from rare earths by cation-exchange with gradient elute α-hydroxy-iso-butyric acid. During projects by AQCS IAEA 'Evaluation of Methods for 90 Sr in a Mineral Matrix' and 'Proficiency Test for 239 Pu, 241 Pu and 241 Am Measurement in a Mineral Matrix' accuracy and precision for 90 Sr, 239 Pu and 241 Am by present procedure was evaluated. Advantages, difficulties and limitations of the method are discussed. (author)

Reaction kinetics of irradiation prepolymerized MMA-PU IPN by 5DXC FTIR

International Nuclear Information System (INIS)

Wu Yiming; Zhang Zhiping; Luo Ning

2000-01-01

The reaction kinetics of irradiation-prepolymerized MMA-PU (polyether) IPNs have been studied by FTIR. The results indicate that the polymerization of each component in the IPN follows its normal distinct reaction mechanism with no mutual interference. Increasing the concentration of TMPTAM (crosslinking agent of PMMA) increased the formation rate of PMMA, while the formation rate of PU networks remained almost the same. Increasing the concentration of TMP (crosslinking agent of PU) increased the formation rate of PU, while the formation rate of PMMA networks decreased. The formation rate of PU was obviously faster than that of PMMA. A theory for the cage effect of the PU network has been proposed. (author)

The application of data derived from autoradiographic studies with 241Pu in the formulation of a bone dosimetric model for 239Pu

International Nuclear Information System (INIS)

Priest, N.D.; Hunt, B.W.

1979-01-01

Recently a dosimetric model for 239 Pu in bone has been published which in conjunction with the general ICRP dosimetric model for actinides is used to calculate annual limits of intake for 239 Pu. This model allows for the burial of plutonium in bone, for the recycling of plutonium within the skeleton and for the retention of plutonium in the bone marrow. The model was based upon published descriptions of the distribution and redistribution patterns of plutonium in bone and on evidence obtained from autoradiographic studies of bone from animals injected with 241 Pu. The experiments with 241 Pu demonstrated the initial uptake of plutonium by bone surfaces. As a result of the growth and drift processes much of this plutonium became either buried in the bone or was retained within macrophages in the bone marrow. (author)

Antibody Immobilization on Conductive Polymer Coated Nonwoven Fibers for Biosensors

Directory of Open Access Journals (Sweden)

Shannon K. MCGRAW

2011-12-01

Full Text Available This work is being performed to develop rapid and novel electrochemical biosensors for foodborne pathogen detection. This research focuses on electrotextile platforms to perform both capture and sensing functions in a single component. The biosensor uses nonwoven fiber membranes coated with conductive polymer and functionalized with antibodies for biological capture. This study examines three methods for antibody immobilization: passive adsorption, glutaraldehyde cross-linking, and EDC/Sulfo-NHS cross-linking. Antibodies are immobilized onto the conductive fiber surfaces for the specific capture of a target pathogen. The immobilization and capture capabilities of each method are analyzed through the use of two different fluorescent reporters: FITC and PicoGreen DNA stain. Fluorescence is measured using a fluorescent plate reader and then imaged using a fluorescent microscope. The effect of a blocking agent on specificity is also evaluated. It is found that glutaraldehyde with blocking is the best immobilization method with PicoGreen being the best fluorescent reporter.

Temporal record of Pu isotopes in inter-tidal sediments from the northeastern Irish Sea

Energy Technology Data Exchange (ETDEWEB)

Lindahl, Patric, E-mail: patriclindahl@yahoo.com [School of Geography, Earth and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Worsfold, Paul; Keith-Roach, Miranda [School of Geography, Earth and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Andersen, Morten B. [Bristol Isotope Group, School of Earth Sciences, University of Bristol, Wills Memorial Building, Bristol BS8 1RJ (United Kingdom); Kershaw, Peter; Leonard, Kins [The Centre for Environment, Fisheries and Aquaculture Science, Lowestoft Laboratory, Pakefield Road, Suffolk NR33 0HT (United Kingdom); Choi, Min-Seok [Division of Earth and Environmental Science, Korea Basic Science Institute, 113 Gwahangno, Yusung-gu, Daejon 305-333 (Korea, Republic of); Boust, Dominique [Laboratoire de Radioecologie, Institut de Radioprotection et de Surete Nucleaire, BP 10, 50130 Cherbourg-Octeville (France); Lesueur, Patrick [University of Caen Basse Normandie, M2C UMR CNRS 6143, 14000 Caen (France)

2011-11-01

A depth profile of {sup 239}Pu and {sup 240}Pu specific activities and isotope ratios was determined in an inter-tidal sediment core from the Esk Estuary in the northeastern Irish Sea. The study site has been impacted with plutonium through routine radionuclide discharges from the Sellafield nuclear reprocessing plant in Cumbria, NW England. A pronounced sub-surface maximum of {approx} 10 kBq kg{sup -1} was observed for {sup 239+240}Pu, corresponding to the peak in Pu discharge from Sellafield in 1973, with a decreasing trend with depth down to {approx} 0.04 kBq kg{sup -1} in the deeper layers. The depth profile of {sup 239+240}Pu specific activities together with results from gamma-ray spectrometry for {sup 137}Cs and {sup 241}Am was compared with reported releases from the Sellafield plant in order to estimate a reliable sediment chronology. The upper layers (1992 onwards) showed higher {sup 239+240}Pu specific activities than would be expected from the direct input of annual Sellafield discharges, indicating that the main input of Pu is from the time-integrated contaminated mud patch of the northeastern Irish Sea. The {sup 240}Pu/{sup 239}Pu atom ratios ranged from {approx} 0.03 in the deepest layers to > 0.20 in the sub-surface layers with an activity-weighted average of 0.181. The decreasing {sup 240}Pu/{sup 239}Pu atom ratio with depth reflects the changing nature of operations at the Sellafield plant from weapons-grade Pu production to reprocessing spent nuclear fuel with higher burn-up times in the late 1950s. In addition, recent annual {sup 240}Pu/{sup 239}Pu atom ratios in winkles collected during 2003-2008 from three stations along the Cumbrian coastline showed no significant spatial or temporal differences with an overall average of 0.204, which supports the hypothesis of diluted Pu input from the contaminated mud patch. - Highlights: {yields} Depth profiles of {sup 239}Pu and {sup 240}Pu determined in a northeastern Irish Sea sediment. {yields

Monte Carlo analysis of Pu-H2O and UO2-PuO2-H2O critical assemblies with ENDF/B-IV data

International Nuclear Information System (INIS)

Hardy, J. Jr.; Ullo, J.J.

1981-04-01

A set of critical experiments, comprising thirteen homogeneous Pu-H 2 O assemblies and twelve UO 2 -PuO 2 lattices, was analyzed with ENDF/B-IV data and the RCPO1 Monte Carlo program, which modeled the experiments explicitly. Some major data sensitivities were also evaluated. For the Pu-H 2 O assemblies, calculated K/sub eff/ averaged 1.011. The large (2.7%) scatter of K/sub eff/ values for these assemblies was attributed mostly to uncertainties in physical specifications since no clear trends of K/sub eff/ were evident and data sensitivities were insignificant. The UO 2 -PuO 2 lattices showed just one trend of K/sub eff/, which indicated an overprediction of U238 capture consistent with that observed for uranium-H 2 O experiments. There was however a approx. 1% discrepancy in calculated K/sub eff/ between the two sets of UO 2 -PuO 2 lattices studied

The hematopoietic transcription factor PU.1 regulates RANK gene expression in myeloid progenitors

International Nuclear Information System (INIS)

Kwon, Oh Hyung; Lee, Chong-Kil; Lee, Young Ik; Paik, Sang-Gi; Lee, Hyun-Jun

2005-01-01

Osteoclasts are bone resorbing cells of hematopoietic origin. The hematopoietic transcription factor PU.1 is critical for osteoclastogenesis; however, the molecular mechanisms of PU.1-regulated osteoclastogenesis have not been explored. Here, we present evidence that the receptor activator of nuclear factor κB (RANK) gene that has been shown to be crucial for osteoclastogenesis is a transcriptional target of PU.1. The PU.1 -/- progenitor cells failed to express the RANK gene and reconstitution of PU.1 in these cells induced RANK expression. Treatment of the PU.1 reconstituted cells with M-CSF and RANKL further augmented the RANK gene expression. To explore the regulatory mechanism of the RANK gene expression by PU.1, we have cloned the human RANK promoter. Transient transfection assays have revealed that the 2.2-kb RANK promoter was functional in a monocyte line RAW264.7, whereas co-transfection of PU.1 transactivated the RANK promoter in HeLa cells. Taken together, these results suggest that PU.1 regulates the RANK gene transcription and this may represent one of the key roles of PU.1 in osteoclast differentiation

Vertical distribution of (241)Pu in the southern Baltic Sea sediments.

Science.gov (United States)

Strumińska-Parulska, Dagmara I

2014-12-15

The vertical distribution of plutonium (241)Pu in marine sediments can assist in determining the deposition history and sedimentation process of analyzed regions. In addition, (241)Pu/(239+240)Pu activity ratio could be used as a sensitive fingerprint for radioactive source identification. The present preliminary studies on vertical distribution of (241)Pu in sediments from four regions of the southern Baltic Sea are presented. The distribution of (241)Pu was not uniform and depended on sediment geomorphology and depth as well as location. The highest concentrations of plutonium were found in the surface layers of all analyzed sediments and originated from the Chernobyl accident. Copyright © 2014 Elsevier Ltd. All rights reserved.

Inhaled 239PuO2 in rats with pulmonary emphysema. II

International Nuclear Information System (INIS)

Lundgren, D.L.; Mauderly, J.L.; Carlton, W.W.; Hahn, F.F.

1988-01-01

The modifying effects of pre-existing pulmonary emphysema on deposition, distribution, retention, and effects of inhaled 239 PuO 2 in the rat were investigated. The presence of emphysema in the rats tested was indicated by respiratory function measurements and confirmed microscopically. Initial lung burdens of 239 Pu per kg body weight were less in rats with emphysema than in control rats; however, the retention of 239 Pu was similar in emphysematous and control rats. Survival and lung tumor occurrence were similar in emphysematous and control rats exposed to 239 PuO 2 . We concluded that rats with pre-existing pulmonary emphysema were not more sensitive to the effects of inhaled 239 PuO 2 than control rats. (author)

Phytoextraction studies for removal of 239Pu using Vetiveria zizanoides plants

International Nuclear Information System (INIS)

Singh, Shraddha; Fulzele, D.P.; Kaushik, C.P.

2015-01-01

The potential of Vetiveria zizanoides, a plant used for environmental conservation was tested for remediation of radionuclide plutonium ( 239 Pu). While the plant could remediate high levels of 239 Pu (65%) from solutions, remediation of radionuclides from soil was limited. Addition of chelating agents such as citric acid (CA) and diethylenetriaminepentaacetic acid (DTPA) enhanced phytoremediation of 239 Pu from soil. Translocation of 239 Pu to the shoot biomass showed an enhancement in the presence of chelating agents. The present studies have shown that V. zizanoides is a suitable candidate plant for remediation of 239 Pu and addition of DTPA enhanced translocation of radionuclide to shoot which may further lead to phytoextraction. (author)

Relations between blended learning possibilities and teachers' approaches to blended learning

DEFF Research Database (Denmark)

Stenalt, Maria Hvid; Nielsen, Tobias Alsted; Bager-Elsborg, Anna

Higher Education has embraced blended learning as a way of enhancing quality in teaching and helping students to learn. This presentation addresses relations between blended learning possiblities presented to teachers in a teacher training project and teachers’ approaches to blended learning. We...... suggest that in order to identify the level of impact of integrating technologies in teaching and learning, we need to understand the factors influencing approaches to design of courses for blended contexts. Participants in the teacher training project come from the Department of Law at Aarhus University......: • Optain locally-embedded knowledge about blended learning • Develop opportunities for law students to receive (more) feedback • Comply with strategic aims The results so far suggest that teachers provide a disciplinary perspective on the key dimensions of blended learning, which influences...

First principles study of α and δ-Pu

International Nuclear Information System (INIS)

Chattaraj, Debabrata; Dash, Smruti

2017-01-01

The structural and electronic properties of α-and δ-Pu has been investigated using state of the art first principles method. All the calculations have been performed using a plane wave based pseudopotential method under the framework of spin polarized density functional theory. The effect of relativistic spin-orbit interactions on these properties has been investigated. The calculated lattice parameters are found to be within ±1% of the experimental data. The cohesive energy of α-and δ-Pu are calculated to be -3.125 and -3.126 eV/atom. The nature of chemical bonding present in those phases of Pu is depicted by calculated density of states spectra. (author)

Base case Pu-nitrate to Pu-oxide conversion plant

International Nuclear Information System (INIS)

1978-10-01

This paper explains that the plutonium recovered in the course of reprocessing spent fuel is obtained in the form of plutonium nitrate, whereas PuO 2 is required for the fabrication of fuel rods. The reference conversion plant described in the paper converts plutonium nitrate into plutonium dioxide powder by precipitation with oxalic acid followed by calcination. The paper also describes the main features of the safety, maintenance and safeguards philosophy used in its design

Microautoradiography in studies of Pu(V) sorption by trace and fracture minerals in tuff

International Nuclear Information System (INIS)

Vaniman, D.; Furlano, A.; Chipera, S.; Thompson, J.; Triay, I.

1996-01-01

Microautoradiography was used to evaluate the mineralogic basis of Pu(V) retention by tuffs from Yucca Mountain, Nevada. Altered orthopyroxenes and oxide minerals are associated with high Pu retention but are limited to specific stratigraphic horizons. A weaker but more general association of Pu with smectite occurs in most samples. Thin-sections that cross fractures allow comparative studies of Pu retention by fracture-lining versus matrix minerals. Using Ag metal in emulsions as a measure of underlying Pu concentration, electron-microprobe analysis can quantify Pu retention along fracture walls and provide mineral/mineral Pu retention factors. For smectite-lined microfractures in zeolitized tuff, the smectite/clinoptilolite Pu retention factor is >80

Transport process of Pu isotope in marginal seas of the western North Pacific Ocean

Energy Technology Data Exchange (ETDEWEB)

Yamada, Masatoshi [Department of Radiation Chemistry, Institute of Radiation Emergency Medicine, Hirosaki University, Hirosaki, 036-8564, Aomori (Japan); Zheng, Jian [Research Center for Radiation Protection, National Institute of Radiological Sciences, 4-9-1 Anagawa, Inage, 263-8555, Chiba (Japan)

2014-07-01

Significant quantities of Pu isotopes have been released into the marine environment as the result of atmospheric nuclear weapons testing. Most radionuclides globally dispersed in atmospheric nuclear weapons testing were released into the environment during the 1950's and 1960's. In the western North Pacific Ocean, the principal source can be further distinguished as two distinct sources of Pu: close-in tropospheric fallout from nuclear weapons testing at the Pacific Proving Grounds (PPG) in the Marshall Islands and global stratospheric fallout. Since the {sup 240}Pu/{sup 239}Pu atom ratio is characteristic for the Pu emission source, information on Pu isotopic signature is very useful to better understand the transport process in the oceans and to identify the sources of Pu. The mean atom ratio of {sup 240}Pu/{sup 239}Pu from the global stratospheric fallout is 0.180 ±0.014 based on soil sample data, whereas that from close-in tropospheric fallout from the PPG is 0.33 - 0.36. The {sup 240}Pu/{sup 239}Pu atom ratios in seawater samples collected in marginal seas of the western North Pacific Ocean will provide important and useful data for understanding the process controlling Pu transport and for distinguishing future Pu sources. The objectives of this study were to measure the {sup 239+240}Pu concentrations and {sup 240}Pu/{sup 239}Pu atom ratios in seawater from the Sea of Okhotsk, Japan Sea, South China Sea and Sulu Sea and to discuss the transport process of Pu. Large-volume seawater samples (250 L each) were collected from the surface to the bottom in marginal seas of the western North Pacific Ocean with acoustically triggered quadruple PVC sampling bottles during the R/V Hakuho-Maru cruise. The {sup 239}Pu and {sup 240}Pu concentrations and {sup 240}Pu/{sup 239}Pu atom ratios were measured with a double-focusing SF-ICP-MS, which was equipped with a guard electrode to eliminate secondary discharge in the plasma and to enhance overall sensitivity. In

DFT and two-dimensional correlation analysis methods for evaluating the Pu{sup 3+}–Pu{sup 4+} electronic transition of plutonium-doped zircon

Energy Technology Data Exchange (ETDEWEB)

Bian, Liang, E-mail: bianliang@ms.xjb.ac.cn [Key Laboratory of Functional Materials and Devices for Special Environments, Chinese Academy of Sciences, Urumqi 830011, Xinjiang (China); Laboratory for Extreme Conditions Matter Properties, South West University of Science and Technology, Mianyang 621010, Sichuan (China); Dong, Fa-qin; Song, Mian-xin [Laboratory for Extreme Conditions Matter Properties, South West University of Science and Technology, Mianyang 621010, Sichuan (China); Dong, Hai-liang [Department of Geology and Environmental Earth Science, Miami University, Oxford, OH 45056 (United States); Li, Wei-Min [Key Laboratory of Functional Materials and Devices for Special Environments, Chinese Academy of Sciences, Urumqi 830011, Xinjiang (China); Duan, Tao; Xu, Jin-bao [Laboratory for Extreme Conditions Matter Properties, South West University of Science and Technology, Mianyang 621010, Sichuan (China); Zhang, Xiao-yan [Key Laboratory of Functional Materials and Devices for Special Environments, Chinese Academy of Sciences, Urumqi 830011, Xinjiang (China); Laboratory for Extreme Conditions Matter Properties, South West University of Science and Technology, Mianyang 621010, Sichuan (China)

2015-08-30

Highlights: • Effect of Pu f-shell electron on the electronic property of zircon is calculated via DFT and 2D-CA techniques. • Reasons of Pu f-shell electron influencing on electronic properties are systematically discussed. • Phase transitions are found at two point 2.8 mol% and 7.5 mol%. - Abstract: Understanding how plutonium (Pu) doping affects the crystalline zircon structure is very important for risk management. However, so far, there have been only a very limited number of reports of the quantitative simulation of the effects of the Pu charge and concentration on the phase transition. In this study, we used density functional theory (DFT), virtual crystal approximation (VCA), and two-dimensional correlation analysis (2D-CA) techniques to calculate the origins of the structural and electronic transitions of Zr{sub 1−c}Pu{sub c}SiO{sub 4} over a wide range of Pu doping concentrations (c = 0–10 mol%). The calculations indicated that the low-angular-momentum Pu-f{sub xy}-shell electron excites an inner-shell O-2s{sup 2} orbital to create an oxygen defect (V{sub O-s}) below c = 2.8 mol%. This oxygen defect then captures a low-angular-momentum Zr-5p{sup 6}5s{sup 2} electron to form an sp hybrid orbital, which exhibits a stable phase structure. When c > 2.8 mol%, each accumulated V{sub O-p} defect captures a high-angular-momentum Zr-4d{sub z} electron and two Si-p{sub z} electrons to create delocalized Si{sup 4+} → Si{sup 2+} charge disproportionation. Therefore, we suggest that the optimal amount of Pu cannot exceed 7.5 mol% because of the formation of a mixture of ZrO{sub 8} polyhedral and SiO{sub 4} tetrahedral phases with the orientation (10-1). This study offers new perspective on the development of highly stable zircon-based solid solution materials.

Magnetic susceptibility of sodium disilicate glasses containing PuO2

International Nuclear Information System (INIS)

Aldred, A.T.

1979-01-01

A solubility limit of approx. 6 mol % PuO 2 in sodium disilicate (Na 2 O.2SiO 2 ) glass has been determined. Magnetic susceptibility measurements on these glasses yield approximate Curie-Weiss behavior, in contrast to the temperature-independent susceptibility of crystalline PuO 2 . This result is interpreted to indicate that the local site symmetry around the Pu ion in the sodium disilicate glass is much different than in crystalline PuO 2 . The effective paramagnetic moments determined from the temperature dependence of the susceptibility are found to be consistent with calculated free-ion values based on the most likely 5f electron configurations

Improved Sound Absorption Performance of Nonwoven Fabric using Fabric Facing and Air Back Cavity

Directory of Open Access Journals (Sweden)

Ismail Ahmad Yusuf

2017-01-01

Full Text Available This paper presents the improvement methods to increase sound absorption performance of polyethylene based nonwoven fabric (PNF. The methods are placing a woven fabric in front of the sample as well as providing air cavity behind the sample. The samples were experimentally tested in an impedance tube based on ISO 10354-2:2001 whereby two microphones are used and the transfer matrix methods are employed. From the results, it can be seen that placing front woven fabric effectively increases sound absorption performance. Moreover, introducing air cavity gap behind the sample is also found to be more significant to increase sound absorption.

Pu and 137Cs in the Yangtze River estuary sediments: distribution and source identification.

Science.gov (United States)

Liu, Zhiyong; Zheng, Jian; Pan, Shaoming; Dong, Wei; Yamada, Masatoshi; Aono, Tatsuo; Guo, Qiuju

2011-03-01

Pu isotopes and (137)Cs were analyzed using sector field ICP-MS and γ spectrometry, respectively, in surface sediment and core sediment samples from the Yangtze River estuary. (239+240)Pu activity and (240)Pu/(239)Pu atom ratios (>0.18) shows a generally increasing trend from land to sea and from north to south in the estuary. This spatial distribution pattern indicates that the Pacific Proving Grounds (PPG) source Pu transported by ocean currents was intensively scavenged into the suspended sediment under favorable conditions, and mixed with riverine sediment as the water circulated in the estuary. This process is the main control for the distribution of Pu in the estuary. Moreover, Pu is also an important indicator for monitoring the changes of environmental radioactivity in the estuary as the river basin is currently the site of extensive human activities and the sea level is rising because of global climate changes. For core sediment samples the maximum peak of (239+240)Pu activity was observed at a depth of 172 cm. The sedimentation rate was estimated on the basis of the Pu maximum deposition peak in 1963-1964 to be 4.1 cm/a. The contributions of the PPG close-in fallout Pu (44%) and the riverine Pu (45%) in Yangtze River estuary sediments are equally important for the total Pu deposition in the estuary, which challenges the current hypothesis that the riverine Pu input was the major source of Pu budget in this area.

The evaluation of the mass distribution data for 238U, 239Pu and 242Pu fission

International Nuclear Information System (INIS)

Liu Tingjin

2002-01-01

The mass distribution data for 238 U at E n =1.5, 5.5, 8.3, 11.3, 14.9, 22.0, 27.5, 50.0, 99.5, 160.0 MeV, E p =20.0, 60.0 MeV 239 Pu at E n =0.17, 7.9, 14.5 MeV and 242 Pu at E n =15.1 MeV were evaluated and recommended based on the main available experimental data up to now. The experimental data were make necessary corrections and their errors were also made necessary adjustments. The problems concerned were discussed

Multilevel resonance parameters of 241Pu

International Nuclear Information System (INIS)

Weston, L.W.; Todd, J.H.

1978-01-01

The data previously reported by the authors on the neutron fission and capture cross sections of 241 Pu were simultaneously fit with the Adler formalism to obtain multilevel resonance parameters. The neutron energy range of the fit was 0.01 to 100 eV. The 241 Pu cross sections in the resonance region of neutron energies are complex, and the Adler parameters present an efficient method of representing these cross sections, which are important for plutonium-fueled reactors. The parameters represent the data to an accuracy within the quoted experimental errors. 5 figures, 2 tables

The concentrations of sup(239.240)Pu in foods of the Japanese

International Nuclear Information System (INIS)

Okabayashi, Hiroyuki; Watanabe, Mineo; Takizawa, Yukio.

1981-01-01

Measurements of the amounts of sup(239.240)Pu in total daily diet and in marine foods were conducted to estimate the dietary intake of sup(239.240)Pu in the Japanese. The average concentrations of sup(239.240)Pu in total diet of various places in Japan were 96 fCi/day/person in 1968 and 50 fCi/day/person in 1969. It was found that the concentration of sup(239.240)Pu in total diet decreased with the decrease of radioactive fallout. The concentrations of sup(239.240)Pu in viscera and bone of marinefishes and in seaweeds were high. The average amount of dietary intake of sup(239.240)Pu from marine foods by the Japanese at present was about 9 fCi/day/person. It was estimated that the greater part of sup(239.240)Pu in total diet of the Japanese was due to the marine foods. (author)

LEAD SLOWING DOWN SPECTROSCOPY FOR DIRECT Pu MASS MEASUREMENTS

International Nuclear Information System (INIS)

Ressler, Jennifer J.; Smith, Leon E.; Anderson, Kevin K.

2008-01-01

The direct measurement of Pu in previously irradiated fuel assemblies is a recognized need in the international safeguards community. A suitable technology could support more timely and independent material control and accounting (MC and A) measurements at nuclear fuel storage areas, the head-end of reprocessing facilities, and at the product-end of recycled fuel fabrication. Lead slowing down spectroscopy (LSDS) may be a viable solution for directly measuring not only the mass of 239Pu in fuel assemblies, but also the masses of other fissile isotopes such as 235U and 241Pu. To assess the potential viability of LSDS, an LSDS spectrometer was modeled in MCNP5 and 'virtual assays' of nominal PWR assemblies ranging from 0 to 60 GWd/MTU burnup were completed. Signal extraction methods, including the incorporation of nonlinear fitting to account for self-shielding effects in strong resonance regions, are described. Quantitative estimates of Pu uncertainty are given for simplistic and more realistic fuel isotopic inventories calculated using ORIGEN. A discussion of additional signal-perturbing effects that will be addressed in future work, and potential signal extraction approaches that could improve Pu mass uncertainties, are also discussed

New CO2 adsorbent containing aminated poly(glycidyl methacrylate) grafted onto irradiated PE-PP nonwoven sheet

Science.gov (United States)

Mahmoud Nasef, Mohamed; Abbasi, Ali; Ting, T. M.

2014-10-01

A new CO2 adsorbent containing triethylamine (TEA) was prepared by radiation induced grafting of glycidyl methacrylate (GMA) onto polyethylene coated polypropylene (PE-PP) non-woven sheet followed by amination reaction. The degree of grafting (DOG%) was controlled by variation of monomer concentration and absorbed dose. The incorporation of aminated poly(GMA) was investigated by Fourier transform infrared (FTIR) and scanning electron microscope (SEM). The adsorbent with DOG of 350% and amination yield of 60% exhibited CO2 adsorption capacity of 4.52 mol/kg at ambient temperature and pressure.

Blended Learning

NARCIS (Netherlands)

Van der Baaren, John

2009-01-01

Van der Baaren, J. (2009). Blended Learning. Presentation given at the Mini symposium 'Blended Learning the way to go?'. November, 5, 2009, The Hague, The Netherlands: Netherlands Defence Academy (NDLA).

Toxicity of inhaled 238PuO2 II

International Nuclear Information System (INIS)

Muggenburg, B.A.; Mewhinney, J.A.; Merickel, B.S.; Boecker, B.B.; Hahn, F.F.; Guilmette, R.A.; Mauderly, J.L.; McClellan, R.O.

1980-01-01

Studies are in progress to determine dose-response relationships for inhaled 238 PuO 2 . Beagle dogs were given a single, brief, nose-only inhalation exposure to aerosols of monodisperse particles of 238 PuO 2 . Aerosols of two sizes were used, 1.5 μm aerodynamic diameter (AD) and 3.0 μm AD. Dogs were exposed to achieve initial lung burdens of 0.56, 0.28, 0.14, 0.07, 0.03 or 0.01 μCi 238 PuO 2 /kg body weight. Twelve dogs were exposed at each activity level to each aerosol particle size. The local dose around each 3.0 μm AD particle was 10 times higher than the local dose around 1.5 μm AD particles, but the dose averaged over the whole lung was the same at each activity level for both particle sizes. The lung retention of 238 Pu was divided into two phases of clearance. During the first 100 days after exposure, the average retention half-time for 238 Pu in the lung was 310 days. When the solubility changed due to particle breakup, the retention half-time decreased to 180 days during the period from 1OO to 1,500 days after exposure. The first biological effects observed were lymphopenia and neutropenia in peripheral blood. To date, 28 Beagle dogs have died at times from 536 to 1683 days after exposure. Initial lung burdens for the dead dogs ranged from 0.18 to 2.2 μCi 238 Pu/kg body weight. Nine died with radiation pneumonitis and pulmonary fibrosis, 10 died with lung tumors and 19 dogs died with bone tumors. There are 116 exposed and 22 control dogs surviving and under observation. Current patterns of dose versus response are discussed. (author)

Preparation, microstructures, and properties of PuO2

International Nuclear Information System (INIS)

Bickford, D.F.; Rankin, D.T.; Smith, P.K.

1976-01-01

PuO 2 pellets with controlled microstructures were fabricated to meet operational requirements for packaged heat sources. Size distributions, morphologies (forms and structures), and packing densities were measured on calcined and milled powders, slugged compacts, and presintered granules. These variables influence microstructure, porosity distribution, and fracture behavior of hot-pressed and sintered PuO 2

PuLP/XtraPuLP : Partitioning Tools for Extreme-Scale Graphs

Energy Technology Data Exchange (ETDEWEB)

2017-09-21

PuLP/XtraPulp is software for partitioning graphs from several real-world problems. Graphs occur in several places in real world from road networks, social networks and scientific simulations. For efficient parallel processing these graphs have to be partitioned (split) with respect to metrics such as computation and communication costs. Our software allows such partitioning for massive graphs.

Interatomic potentials for PuC by Chen–Möbius multiple lattice inversion

International Nuclear Information System (INIS)

Huang, H.; Meng, D.Q.; Lai, X.C.; Li, G.; Long, Y.

2013-01-01

The atomic interactions of PuC with B1 structure were described by Chen–Möbius lattice inversion combined with first-principle calculations. In order to obtain the inversion potential parameters of PuC, three different structures including two virtual crystals were built and the Morse function plus a modified term was adopted to fit the pair-potential curves. The reliability of the inversion potential was tested by checking the stability of the transition of PuC from disordered to ordered state and comparing the calculated and experimental physical and thermal properties of PuC. All the results show that the inversion potential could give a stable and accurate description of the atomic interactions in PuC and the physical and thermal properties of PuC are well reproduced by the potential

Spatial and temporal distribution of Pu in the Northwest Pacific Ocean using modern coral archives.

Science.gov (United States)

Lindahl, Patric; Andersen, Morten B; Keith-Roach, Miranda; Worsfold, Paul; Hyeong, Kiseong; Choi, Min-Seok; Lee, Sang-Hoon

2012-04-01

Historical (239)Pu activity concentrations and (240)Pu/(239)Pu atom ratios were determined in skeletons of dated modern corals collected from three locations (Chuuk Lagoon, Ishigaki Island and Iki Island) to identify spatial and temporal variations in Pu inputs to the Northwest Pacific Ocean. The main Pu source in the Northwest Pacific is fallout from atmospheric nuclear weapons testing which consists of global fallout and close-in fallout from the former US Pacific Proving Grounds (PPG) in the Marshall Islands. PPG close-in fallout dominated the Pu input in the 1950s, as was observed with higher (240)Pu/(239)Pu atom ratios (>0.30) at the Ishigaki site. Specific fallout Pu contamination from the Nagasaki atomic bomb and the Ivy Mike thermonuclear detonation at the PPG were identified at Ishigaki Island from the (240)Pu/(239)Pu atom ratios of 0.07 and 0.46, respectively. During the 1960s and 1970s, global fallout was the major Pu source to the Northwest Pacific with over 60% contribution to the total Pu. After the cessation of the atmospheric nuclear tests, the PPG again dominated the Pu input due to the continuous transport of remobilised Pu from the Marshall Islands along the North Equatorial Current and the subsequent Kuroshio Current. The Pu contributions from the PPG in recent coral bands (1984 onwards) varied over time with average estimated PPG contributions between 54% and 72% depending on location. Copyright © 2011 Elsevier Ltd. All rights reserved.

Measurements of the neutron-induced fission cross sections of 240Pu and 242Pu relative to 235U

International Nuclear Information System (INIS)

Behrens, J.W.; Browne, J.C.; Carlson, G.W.

1976-01-01

A continuation is given of the fission-cross-section ratio measurements in progress at the Lawrence Livermore Laboratory. Preliminary results are provided for the 240 Pu/ 235 U and 242 Pu/ 235 U ratios from 0.02 to 30 MeV and 0.1 to 30 MeV, respectively. Using the threshold-cross-section method, the ratios were normalized to the values 1.368 +- 0.030 and 1.116 +- 0.025, respectively, from 1.75 to 4.00 MeV

Study of phase equilibrium of Pu{sub 2}O{sub 3}-PuO{sub 2} system by the first-principles calculation and CALPHAD approach

Energy Technology Data Exchange (ETDEWEB)

Minamoto, Satoshi [ITOCHU Techno-Solutions Corporation, Kasumigaseki 3, Chiyoda-ku, Tokyo, Energy and Industrial Systems Department (Japan); Kato, Masato [Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki (Japan); Konashi, Kenji, E-mail: satoshi.minamoto@ctc-g.co.jp, E-mail: masato.kato@jaea.go.jp, E-mail: konashi@imr.tohoku-u.ac.jp [Institute for Materials Research, Tohoku University, Oarai-chou, Ibaraki (Japan)

2010-03-15

A combination of a first-principles calculation, lattice dynamics and CALPHAD (CALculation of PHAse Diagrams) modeling is proven as a powerful tool so as to evaluate the Gibbs free energy and a phase equilibrium between compounds including large amount of vacancies. In this work, non-stoichiometric PuO{sub 2-x} (dioxide) and Pu{sub 2}O{sub 3} (sesquioxide) has been studied. An electron cohesive energy was evaluated from a first-principles calculations to estimate total energy of the compounds and a vacancy formation energy, and the theory of statistical mechanics was applied to evaluate enthalpy/entropy change due to oxygen vacancies for the non-stoichiometry of the PuO{sub 2} (i.e. PuO{sub 2-x}). Then a vacancy-vacancy interaction energy was determined by fitting to the experimental data of a quantity of non-stoichiometry of the PuO{sub 2} compounds as a function of oxygen potentials at large deviation from stoichiometry. The resulting Gibbs free energy yields phase boundary between the phases with good agreement with to the experimental data.

Non-destructive assay of 242Pu by resonance neutron capture

International Nuclear Information System (INIS)

Kane, W.R.; Lu, Ming-Shih; Aronson, A.; Forman, L.; Vanier, P.E.

1995-01-01

For the accurate assay of plutonium by neutron correlation measurements, especially for material derived from high-burnup reactor fuel, the content of 242 Pu in a sample must be determined. Since 242 Pu has a long half-life (387,000 yr) and decays to 238 U by alpha particle emission with the accompanying emission of only weak, low-energy gamma rays, gamma-ray spectrometry methods which are ordinarily employed to determine the isotopic composition of a plutonium sample are not feasible for 242 Pu. The existence of a resonance in the neutron capture cross section of 242 Pu at an energy of 2.67 electron volts (eV) with a large (72, 000 barn) cross section affords the possibility for the quantitative assay of this isotope by epithermal neutron capture. Essential for this purpose is an appropriately designed geometry of neutron moderators and absorbers which will provide maximum flux in the eV region while suppressing thermal neutron capture by the fissile plutonium isotopes. Signatures for neutron capture in 242 Pu include the decay of 243 Pu (4.9 hr), prompt capture gamma rays (total energy 5.034 MeV), and the decay of an isomeric state (330 nanosecond). Experiments to determine the feasibility of this approach are currently in progress

Current technics and management strategy for Pu-contaminated wastes at PNC

International Nuclear Information System (INIS)

1981-02-01

Power Reactor and Nuclear Fuel Development Corporation (PNC) was designated as a leading organization for the Pu-contaminated waste technology program in Japan. For this purpose, number of efforts in the research and development are proceeding. That is, Pu-contaminated waste technology including volume reduction system and the immobilization of wastes is being developed. The design of a Pu-contaminated waste treatment facility (PWTF) is being made for the demonstration of the technology developed. Studies are in progress to find the criteria for waste products in disposal. The current procedures and strategy for the management of Pu-contaminated wastes at PNC are described as follows: current and future management; technology development including controlled air incineration, acid digestion, immobilization melting, dismantling, and liquid waste treatment; the Pu-contaminated waste treatment facility. (J.P.N.)

Polymer blends

Energy Technology Data Exchange (ETDEWEB)

Allen, Scott D.; Naik, Sanjeev

2017-08-22

The present invention provides, among other things, extruded blends of aliphatic polycarbonates and polyolefins. In one aspect, provided blends comprise aliphatic polycarbonates such as poly(propylene carbonate) and a lesser amount of a crystalline or semicrystalline polymer. In certain embodiments, provided blends are characterized in that they exhibit unexpected improvements in their elongation properties. In another aspect, the invention provides methods of making such materials and applications of the materials in applications such as the manufacture of consumer packaging materials.

Pu-erh Tea Inhibits Tumor Cell Growth by Down-Regulating Mutant p53

Science.gov (United States)

Zhao, Lanjun; Jia, Shuting; Tang, Wenru; Sheng, Jun; Luo, Ying

2011-01-01

Pu-erh tea is a kind of fermented tea with the incorporation of microorganisms’ metabolites. Unlike green tea, the chemical characteristics and bioactivities of Pu-erh tea are still not well understood. Using water extracts of Pu-erh tea, we analyzed the tumor cell growth inhibition activities on several genetically engineered mouse tumor cell lines. We found that at the concentration that did not affect wild type mouse embryo fibroblasts (MEFs) growth, Pu-erh tea extracts could inhibit tumor cell growth by down-regulated S phase and cause G1 or G2 arrest. Further study showed that Pu-erh tea extracts down-regulated the expression of mutant p53 in tumor cells at the protein level as well as mRNA level. The same concentration of Pu-erh tea solution did not cause p53 stabilization or activation of its downstream pathways in wild type cells. We also found that Pu-erh tea treatment could slightly down-regulate both HSP70 and HSP90 protein levels in tumor cells. These data revealed the action of Pu-erh tea on tumor cells and provided the possible mechanism for Pu-erh tea action, which explained its selectivity in inhibiting tumor cells without affecting wild type cells. Our data sheds light on the application of Pu-erh tea as an anti-tumor agent with low side effects. PMID:22174618