WorldWideScience

Sample records for radio relay sites

  1. Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

    KAUST Repository

    Park, Kihong; Alouini, Mohamed-Slim

    2014-01-01

    In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary

  2. A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

    KAUST Repository

    Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

    2013-01-01

    In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward

  3. Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

    KAUST Repository

    Park, Kihong

    2014-05-01

    In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary user (PU) is located close to the relay nodes, the performance of the secondary network is severely degraded due to the interference power constraint during the transmission in the second hop. We propose a decode and zero-forcing forward scheme to suppress the interference power at the relay nodes and analyze the statistics of the end-to-end signal-to-noise ratio when the relay nodes are located arbitrarily and experience therefore non-identical Rayleigh fading channels. Numerical results validate our theoretical results and show that our proposed scheme improves the performance of the CR network when the PU is close to the relay nodes. © 2014 IEEE.

  4. A low complexity algorithm for multiple relay selection in two-way relaying Cognitive Radio networks

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-06-01

    In this paper, a multiple relay selection scheme for two-way relaying cognitive radio network is investigated. We consider a cooperative Cognitive Radio (CR) system with spectrum sharing scenario using Amplify-and-Forward (AF) protocol, where licensed users and unlicensed users operate on the same frequency band. The main objective is to maximize the sum rate of the unlicensed users allowed to share the spectrum with the licensed users by respecting a tolerated interference threshold. A practical low complexity heuristic approach is proposed to solve our formulated optimization problem. Selected numerical results show that the proposed algorithm reaches a performance close to the performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity. In addition, these results show that our proposed scheme significantly outperforms the single relay selection scheme. © 2013 IEEE.

  5. A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-09-01

    In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward (AF) protocol are optimally selected to maximize the sum rate of the secondary users without degrading the Quality of Service (QoS) of the primary users by respecting a tolerated interference threshold. A strong optimization tool based on genetic algorithm is employed to solve our formulated optimization problem where discrete relay power levels are considered. Our simulation results show that the practical heuristic approach achieves almost the same performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions. Copyright © 2013 by the Institute of Electrical and Electronic Engineers, Inc.

  6. Is a Multi-Hop Relay Scheme Gainful in an IEEE 802.22-Based Cognitive Radio System?

    Science.gov (United States)

    Shin, Jungchae; Lee, Dong-Kyu; Cho, Ho-Shin

    In this paper, we formulate a plan to operate multi-hop relays in IEEE 802.22-based cognitive radio (CR) systems and evaluate system performance to consider the propriety of a multi-hop relay scheme in CR systems. A centralized radio resource management and a simple deployment of relay stations (RSs) are assessed to make relay operations feasible under CR conditions. Simulation results show that the proposed multi-hop relay scheme significantly increases system throughput compared to a no-relay CR system as the incumbent user (IU) traffic gets heavier. Furthermore, the optimal number of hops can be determined given the traffic conditions.

  7. Relay-Assisted Primary and Secondary Transmissions in Cognitive Radio Networks

    KAUST Repository

    Shafie, Ahmed El; Khattab, Tamer; Salem, Ahmed Sultan

    2016-01-01

    We assume a set of cognitive relay nodes that assists both primary and secondary transmissions in a time-slotted cognitive radio networks. To regulate the channel access of the various nodes in the network, we propose an overlapped spectrum sensing

  8. Cross-layer combining of information-guided transmission withnetwork coding relaying for multiuser cognitive radio systems

    KAUST Repository

    Yang, Yuli; Aï ssa, Sonia

    2013-01-01

    For a cognitive radio relaying network, we propose a cross-layer design by combining information-guided transmission at the physical layer and network coding at the network layer. With this design, a common relay is exploited to help

  9. Cross-layer combining of information-guided transmission withnetwork coding relaying for multiuser cognitive radio systems

    KAUST Repository

    Yang, Yuli

    2013-02-01

    For a cognitive radio relaying network, we propose a cross-layer design by combining information-guided transmission at the physical layer and network coding at the network layer. With this design, a common relay is exploited to help the communications between multiple secondary source-destination pairs, which allows for a more efficient use of the radio resources, and moreover, generates less interference to primary licensees in the network. Considering the spectrum-sharing constraints on the relay and secondary sources, the achievable data rate of the proposed cross-layer design is derived and evaluated. Numerical results on average capacity and uniform capacity in the network under study substantiate the efficiency of our proposed design. © 2013 IEEE.

  10. Precoder Design and Power Allocation for MIMO Cognitive Radio Two-Way Relaying Systems

    KAUST Repository

    Sboui, Lokman

    2016-08-11

    In this paper, we study a multiple-antenna two-way relaying (TWR) cognitive radio (CR) system. A space alignment (SA) technique is adopted by the secondary users (SUs) to avoid interference with the primary users (PUs). We derive the optimal power allocation that maximizes the TWR achievable SU sum- rate while respecting the total power budget and the relay power constraints. We also analyze the case in which the relay is able to optimize its gain matrix structure to enhance the SU sum-rate. In the numerical results, we quantify the sum-rate gain of using the SA in the TWR CR and we show that the SU sum-rate is very limited when the relay power is low or the PU power and its resulting interference are high. In addition, we optimize the relay gain using an iterative algorithm and compare between different relay matrix structures.

  11. Achievable Rates of UAV-Relayed Cooperative Cognitive Radio MIMO Systems

    KAUST Repository

    Sboui, Lokman; Ghazzai, Hakim; Rezki, Zouheir; Alouini, Mohamed-Slim

    2017-01-01

    We study the achievable rate of an uplink MIMO cognitive radio system where the primary user (PU) and the secondary user (SU) aim to communicate to the closest primary base station (BS) via a multi-access channel through the same unmanned aerial vehicle (UAV) relay. The SU message is then forwarded from the primary BS to the secondary network with a certain incentive reward as a part of the cooperation protocol between both networks. A special linear precoding scheme is proposed to enable the SU to exploit the PU free eigenmodes. We analyze two scenarios in which the UAV relay gain matrix is either fixed or optimized. We derive the optimal power allocation that maximizes the achievable rate of the SU respecting power budget, interference, and relay power constraints. Numerical results highlight the cognitive rate gain of our proposed scheme with respect to various problem parameters. We also highlight the effect of UAV altitude on the SU and PU rates. Finally, when the relay matrix is optimized, we show that the PU rate is remarkably enhanced and that the SU rate is only improved at high power regime.

  12. Achievable Rates of UAV-Relayed Cooperative Cognitive Radio MIMO Systems

    KAUST Repository

    Sboui, Lokman

    2017-04-19

    We study the achievable rate of an uplink MIMO cognitive radio system where the primary user (PU) and the secondary user (SU) aim to communicate to the closest primary base station (BS) via a multi-access channel through the same unmanned aerial vehicle (UAV) relay. The SU message is then forwarded from the primary BS to the secondary network with a certain incentive reward as a part of the cooperation protocol between both networks. A special linear precoding scheme is proposed to enable the SU to exploit the PU free eigenmodes. We analyze two scenarios in which the UAV relay gain matrix is either fixed or optimized. We derive the optimal power allocation that maximizes the achievable rate of the SU respecting power budget, interference, and relay power constraints. Numerical results highlight the cognitive rate gain of our proposed scheme with respect to various problem parameters. We also highlight the effect of UAV altitude on the SU and PU rates. Finally, when the relay matrix is optimized, we show that the PU rate is remarkably enhanced and that the SU rate is only improved at high power regime.

  13. Relay-Assisted Primary and Secondary Transmissions in Cognitive Radio Networks

    KAUST Repository

    Shafie, Ahmed El

    2016-09-27

    We assume a set of cognitive relay nodes that assists both primary and secondary transmissions in a time-slotted cognitive radio networks. To regulate the channel access of the various nodes in the network, we propose an overlapped spectrum sensing strategy for channel sensing, where the secondary source node senses the channel from the beginning of the time slot and the cognitive relay nodes sense the channel for double the sensing time used by the secondary source node to detect the activities of both the primary and secondary source nodes. Hence, the secondary source node has an intrinsic priority over the relay nodes. The relay nodes help both the primary user and the secondary user to deliver their unsuccessfully decoded packets at their destinations. In a given time slot, the scheduled relay node for data transmission starts its transmission when both the primary and secondary users are sensed to be inactive (i.e. have no data to transmit). We propose two optimization-based formulations with quality-of-service (QoS) constraints involving average queueing delay and average service rate requirements. We investigate both cases of perfect and imperfect spectrum sensing. To further enhance the users\\' QoS requirements, we propose three packet decoding strategies at the relay nodes and compare their performance. We derive an upper bound on the secondary queue average service rate to determine which decoding strategy can achieve that bound. Our numerical results show the benefits of relaying and its ability to enhance the performance of both the primary and secondary users. Moreover, the performance of the proposed schemes is close to the derived upper bound.

  14. On the throughput of cognitive radio MIMO systems assisted with UAV relays

    KAUST Repository

    Sboui, Lokman; Ghazzai, Hakim; Rezki, Zouheir; Alouini, Mohamed-Slim

    2017-01-01

    We analyze the achievable rates of a cognitive radio MIMO system assisted by an unmanned aerial vehicle (UAV) relay. The primary user (PU) and the secondary user (SU) aim to communicate to the closest primary base station (BS) via a multi

  15. Achievable Rate of Multi-relay Cognitive Radio MIMO Channel with Space Alignment

    KAUST Repository

    Sboui, Lokman; Ghazzai, Hakim; Rezki, Zouheir; Alouini, Mohamed-Slim

    2015-01-01

    We study the impact of multiple relays on the primary user (PU) and secondary user (SU) rates of underlay MIMO cognitive radio. Both users exploit amplify-and-forward relays to communicate with the destination. A space alignment technique and a special linear precoding and decoding scheme are applied to allow the SU to use the resulting free eigenmodes. In addition, the SU can communicate over the used eigenmodes under the condition of respecting an interference constraint tolerated by the PU. At the destination, a successive interference cancellation (SIC) is performed to estimate the secondary signal. We present the explicit expressions of the optimal PU and SU powers that maximize their achievable rates. In the numerical results, we show that our scheme provides cognitive rate gain even in absence of tolerated interference. In addition, we show that increasing the number of relays enhances the PU and SU rates at low power regime and/or when the relays power is sufficiently high.

  16. Achievable Rate of Multi-relay Cognitive Radio MIMO Channel with Space Alignment

    KAUST Repository

    Sboui, Lokman

    2015-04-21

    We study the impact of multiple relays on the primary user (PU) and secondary user (SU) rates of underlay MIMO cognitive radio. Both users exploit amplify-and-forward relays to communicate with the destination. A space alignment technique and a special linear precoding and decoding scheme are applied to allow the SU to use the resulting free eigenmodes. In addition, the SU can communicate over the used eigenmodes under the condition of respecting an interference constraint tolerated by the PU. At the destination, a successive interference cancellation (SIC) is performed to estimate the secondary signal. We present the explicit expressions of the optimal PU and SU powers that maximize their achievable rates. In the numerical results, we show that our scheme provides cognitive rate gain even in absence of tolerated interference. In addition, we show that increasing the number of relays enhances the PU and SU rates at low power regime and/or when the relays power is sufficiently high.

  17. Improving Spectral Capacity and Wireless Network Coverage by Cognitive Radio Technology and Relay Nodes in Cellular Systems

    DEFF Research Database (Denmark)

    Frederiksen, Flemming Bjerge

    2008-01-01

    Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context have been presented and discussed in this paper. Ideas to improve the wireless transmission by orthogonal OFDM-based communication and to increase the...... the coverage of cellular systems by future wireless networks, relay channels, relay stations and collaborate radio have been presented as well. A revised hierarchical deployment of the future wireless and wired networks are shortly discussed....

  18. Multiuser Radio Resource Allocation for Multiservice Transmission in OFDMA-Based Cooperative Relay Networks

    Directory of Open Access Journals (Sweden)

    Zhang Xing

    2009-01-01

    Full Text Available Abstract The problem of multiservice transmission in OFDMA-based cooperative relay networks is studied comprehensively. We propose a framework to adaptively allocate power, subcarriers, and data rate in OFDMA system to maximize spectral efficiency under the constraints of satisfying multiuser multiservices' QoS requirements. Specifically, first we concentrate on the single-user scenario which considers multiservice transmission in point-to-point cooperative relay network. Based on the analysis of single-user scenario, we extend the multiservice transmission to multiuser point-to-multipoint scenario. Next, based on the framework, we propose several suboptimal radio resource allocation algorithms for multiservice transmissions in OFDMA-based cooperative relay networks to further reduce the computational complexity. Simulation results show that the proposed algorithms yield much higher spectral efficiency and much lower outage probability, which are flexible and efficient for the OFDMA-based cooperative relay system.

  19. Bandwidth and power allocation for two-way relaying in overlay cognitive radio systems

    KAUST Repository

    Alsharoa, Ahmad M.; Ghazzai, Hakim; Yaacoub, Elias E.; Alouini, Mohamed-Slim

    2014-01-01

    In this paper, the problem of both bandwidth and power allocation for two-way multiple relay systems in overlay cognitive radio (CR) setup is investigated. In the CR overlay mode, primary users (PUs) cooperate with cognitive users (CUs) for mutual

  20. On the throughput of cognitive radio MIMO systems assisted with UAV relays

    KAUST Repository

    Sboui, Lokman

    2017-07-20

    We analyze the achievable rates of a cognitive radio MIMO system assisted by an unmanned aerial vehicle (UAV) relay. The primary user (PU) and the secondary user (SU) aim to communicate to the closest primary base station (BS) via a multi-access channel through the same UAV relay. The SU message is then forwarded from the primary BS to the secondary network with a certain incentive reward as a part of the cooperation protocol between both networks. We propose a special linear precoding scheme to enable the SU to exploit the PU free eigenmodes. We, also, present the expression of the power maximizing both primary and secondary rates under power budget, relay power, and interference constraints. In the numerical results, we evaluate the PU and SU rates of proposed scheme with respect to various problem parameters. We also highlight the effect of the UAV altitude on the SU and PU rates. Finally, we show that the relay matrix variation affects both rates that reach their peaks at different values of the matrix.

  1. Multi-Destination Cognitive Radio Relay Network with SWIPT and Multiple Primary Receivers

    KAUST Repository

    Al-Habob, Ahmed A.

    2017-05-12

    In this paper, we study the performance of simultaneous wireless information and power transfer (SWIPT) technique in a multi-destination dual-hop underlay cognitive relay network with multiple primary receivers. Information transmission from the secondary source to destinations is performed entirely via a decode- and-forward (DF) relay. The relay is assumed to have no embedded power source and to harvest energy from the source signal using a power splitting (PS) protocol and employing opportunistic scheduling to forward the information to the selected destination. We derive analytical expressions for the outage probability assuming Rayleigh fading channels and considering the energy harvesting efficiency at relay, the source maximum transmit power and primary receivers interference constraints. The system performance is also studied at high signal-to-noise ratio (SNR) values where approximate expressions for the outage probability are provided and analyzed in terms of diversity order and coding gain. Monte-Carlo simulations and some numerical examples are provided to validate the derived expressions and to illustrate the effect of various system parameters on the system performance. In contrast to their conventional counterparts where a multi- destination diversity is usually achieved, the results show that the multi-destination cognitive radio relay networks with the SWIPT technique achieve a constant diversity order of one.

  2. Performance Analysis of Secondary Link with Cross-Layer Design and Cooperative Relay in Cognitive Radio Networks

    KAUST Repository

    Ma, Hao

    2012-06-01

    In this thesis, we investigate two different system infrastructures in underlay cognitive radio network, in which two popular techniques, cross-layer design and cooperative communication, are considered, respectively. In particular, we introduce the Aggressive Adaptive Modulation and Coding (A-AMC) into the cross-layer design and achieve the optimal boundary points in closed form to choose the AMC and A-AMC transmission modes by taking into account the Channel State Information (CSI) from the secondary transmitter to both the primary receiver and the secondary receiver. What’s more, for the cooperative communication design, we consider three different relay selection schemes: Partial Relay Selection, Opportunistic Relay Selection and Threshold Relay Selection. The Probability Density Functions (PDFs) of the Signal-to- Noise Ratio (SNR) in each hop for different selection schemes are provided, and then the exact closed-form expressions for the end-to-end packet loss rate in the secondary link considering the cooperation of the Decode-and-Forward (DF) relay for different relay selection schemes are derived.

  3. Robust distributed two-way relay beamforming in cognitive radio networks

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2012-04-01

    In this paper, we present distributed beamformer designs for a cognitive radio network (CRN) consisting of a pair of cognitive (or secondary) transceiver nodes communicating with each other through a set of secondary non-regenerative two-way relays. The secondary network shares the spectrum with a licensed primary user (PU), and operates under a constraint on the maximum interference to the PU, in addition to its own resource and quality of service (QoS) constraints. We propose beamformer designs assuming that the available channel state information (CSI) is imperfect, which reflects realistic scenarios. The performance of proposed designs is robust to the CSI errors. Such robustness is critical in CRNs given the difficulty in acquiring perfect CSI due to loose cooperation between the PUs and the secondary users (SUs), and the need for strict enforcement of PU interference limit. We consider a mean-square error (MSE)-constrained beamformer that minimizes the total relay transmit power and an MSE-balancing beamformer with a constraint on the total relay transmit power. We show that the proposed designs can be reformulated as convex optimization problems that can be solved efficiently. Through numerical simulations, we illustrate the improved performance of the proposed robust designs compared to non-robust designs. © 2012 IEEE.

  4. Relay selection and resource allocation for two-way DF-AF cognitive radio networks

    KAUST Repository

    Alsharoa, Ahmad M.; Bader, Faouzi; Alouini, Mohamed-Slim

    2013-01-01

    In this letter, the problem of relay selection and optimal resource allocation for two-way relaying cognitive radio networks using half duplex amplify-and-forward and decode-and-forward protocols is investigated. The primary and secondary users are assumed to access the spectrum simultaneously, in a way that the interference introduced to the primary users should be below a certain tolerated limit. Dual decomposition and subgradient methods are used to find the optimal power allocation. A suboptimal approach based on a genetic algorithm is also presented. Simulation results show that the proposed suboptimal algorithm offers a performance close to the optimal performance with a considerable complexity saving. © 2013 IEEE.

  5. Relay selection and resource allocation for two-way DF-AF cognitive radio networks

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-08-01

    In this letter, the problem of relay selection and optimal resource allocation for two-way relaying cognitive radio networks using half duplex amplify-and-forward and decode-and-forward protocols is investigated. The primary and secondary users are assumed to access the spectrum simultaneously, in a way that the interference introduced to the primary users should be below a certain tolerated limit. Dual decomposition and subgradient methods are used to find the optimal power allocation. A suboptimal approach based on a genetic algorithm is also presented. Simulation results show that the proposed suboptimal algorithm offers a performance close to the optimal performance with a considerable complexity saving. © 2013 IEEE.

  6. Bandwidth and power allocation for two-way relaying in overlay cognitive radio systems

    KAUST Repository

    Alsharoa, Ahmad M.

    2014-12-01

    In this paper, the problem of both bandwidth and power allocation for two-way multiple relay systems in overlay cognitive radio (CR) setup is investigated. In the CR overlay mode, primary users (PUs) cooperate with cognitive users (CUs) for mutual benefits. In our framework, we propose that the CUs are allowed to allocate a part of the PUs spectrum to perform their cognitive transmission. In return, acting as an amplify-and-forward two-way relays, they are used to support PUs to achieve their target data rates over the remaining bandwidth. More specifically, CUs acts as relays for the PUs and gain some spectrum as long as they respect a specific power budget and primary quality-of-service constraints. In this context, we first derive closed-form expressions for optimal transmit power allocated to PUs and CUs in order to maximize the cognitive objective. Then, we employ a strong optimization tool based on particle swarm optimization algorithm to find the optimal relay amplification gains and optimal cognitive released bandwidths as well. Our numerical results illustrate the performance of our proposed algorithm for different utility metrics and analyze the impact of some system parameters on the achieved performance.

  7. Cognitive Relay Networks: A Comprehensive Survey

    Directory of Open Access Journals (Sweden)

    Ayesha Naeem

    2015-07-01

    Full Text Available Cognitive radio is an emerging technology to deal with the scarcity and requirement of radio spectrum by dynamically assigning spectrum to unlicensed user . This revolutionary technology shifts the paradigm in the wireless system design by all owing unlicensed user the ability to sense, adapt and share the dynamic spectrum. Cognitive radio technology have been applied to different networks and applications ranging from wireless to public saf ety, smart grid, medical, rela y and cellular applications to increase the throughput and spectrum efficiency of the network. Among these applications, cognitive relay networks is one of the application where cognitive radio technology has been applied. Cognitiv e rela y network increases the network throughput by reducing the complete pa th loss and also by ensuring cooper ation among secondary users and cooperation among primary and secondary users. In this paper , our aim is to provide a survey on cognitive relay network. We also provide a detailed review on existing schemes in cognitive relay networks on the basis of relaying protocol, relay cooperation and channel model.

  8. Optimal relay selection and power allocation for cognitive two-way relaying networks

    KAUST Repository

    Pandarakkottilil, Ubaidulla; Aï ssa, Sonia

    2012-01-01

    In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays

  9. On the throughput of a relay-assisted cognitive radio MIMO channel with space alignment

    KAUST Repository

    Sboui, Lokman; Ghazzai, Hakim; Rezki, Zouheir; Alouini, Mohamed-Slim

    2014-01-01

    We study the achievable rate of a multiple antenna relay-assisted cognitive radio system where a secondary user (SU) aims to communicate instantaneously with the primary user (PU). A special linear precoding scheme is proposed to enable the SU to take advantage of the primary eigenmodes. The used eigenmodes are subject to an interference constraint fixed beforehand by the primary transmitter. Due to the absence of a direct link, both users exploit an amplify-and-forward relay to accomplish their transmissions to a common receiver. After decoding the PU signal, the receiver employs a successive interference cancellation (SIC) to estimate the secondary message. We derive the optimal power allocation that maximizes the achievable rate of the SU respecting interference, peak and relay power constraints. Furthermore, we analyze the SIC detection accuracy on the PU throughput. Numerical results highlight the cognitive rate gain achieved by our proposed scheme without harming the primary rate. In addition, we show that the relay has an important role in increasing or decreasing PU and SU rates especially when varying its power and/or its amplifying gain. © 2014 IFIP.

  10. On the throughput of a relay-assisted cognitive radio MIMO channel with space alignment

    KAUST Repository

    Sboui, Lokman

    2014-05-01

    We study the achievable rate of a multiple antenna relay-assisted cognitive radio system where a secondary user (SU) aims to communicate instantaneously with the primary user (PU). A special linear precoding scheme is proposed to enable the SU to take advantage of the primary eigenmodes. The used eigenmodes are subject to an interference constraint fixed beforehand by the primary transmitter. Due to the absence of a direct link, both users exploit an amplify-and-forward relay to accomplish their transmissions to a common receiver. After decoding the PU signal, the receiver employs a successive interference cancellation (SIC) to estimate the secondary message. We derive the optimal power allocation that maximizes the achievable rate of the SU respecting interference, peak and relay power constraints. Furthermore, we analyze the SIC detection accuracy on the PU throughput. Numerical results highlight the cognitive rate gain achieved by our proposed scheme without harming the primary rate. In addition, we show that the relay has an important role in increasing or decreasing PU and SU rates especially when varying its power and/or its amplifying gain. © 2014 IFIP.

  11. Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-05-08

    In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single and multiple relay selection that maximize the sum rate of the secondary network without degrading the quality of service of the primary network by respecting a tolerated interference threshold were formulated. Single relay selection and optimal power allocation for two-way relaying cognitive radio networks using decode-and-forward and amplify-and-forward protocols were studied. Dual decomposition and subgradient methods were used to find the optimal power allocation. The transmission process to exchange two different messages between two transceivers for two-way relaying technique takes place in two time slots. In the first slot, the transceivers transmit their signals simultaneously to the relay. Then, during the second slot the relay broadcasts its signal to the terminals. Moreover, improvement of both spectral and energy efficiency can be achieved compared with the one-way relaying technique. As an extension, a multiple relay selection for both one-way and two-way relaying under cognitive radio scenario using amplify-and-forward were discussed. A strong optimization tool based on genetic and iterative algorithms was employed to solve the 
formulated optimization problems for both single and multiple relay selection, where discrete relay power levels were considered. Simulation results show that the practical and low-complexity heuristic approaches achieve almost the same performance of the optimal relay selection schemes either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity.

  12. Joint Bandwidth and Power Allocation for MIMO Two-Way Relays-Assisted Overlay Cognitive Radio Systems

    KAUST Repository

    Alsharoa, Ahmad; Ghazzai, Hakim; Yaacoub, Elias; Alouini, Mohamed-Slim; Kamal, Ahmed

    2015-01-01

    This paper studies the achievable cognitive sum rate of an overlay cognitive radio (CR) system assisted with multiple antennas two-way relays in which primary users (PUs) cooperate with cognitive users (CUs) for mutual benefits. In this context, the problem of both bandwidth and power allocation is investigated. We propose that the CUs are allowed to allocate a part of the PUs spectrum to perform their cognitive transmission. In return, acting as amplify-and-forward two-way relays, they are exploited to support PUs to reach their target data rates over the remaining bandwidth. Power expressions for optimal transmit power allocated per PU and CU antenna are derived under primary quality-of-service constraint in addition to bandwidth and power budget constraints. More specifically, CUs act as relays for the PUs transmission and gain some spectrum as long as they respect these constraints. After deriving the optimal transmit powers, we employ a strong optimization tool based on swarm intelligence to optimize the full and complex relay amplification gain matrices in addition to the bandwidths released to primary and cognitive transmission. Furthermore, three different utility functions are considered in our optimization problems depending on the level of fairness among CUs.

  13. Joint Bandwidth and Power Allocation for MIMO Two-Way Relays-Assisted Overlay Cognitive Radio Systems

    KAUST Repository

    Alsharoa, Ahmad

    2015-10-08

    This paper studies the achievable cognitive sum rate of an overlay cognitive radio (CR) system assisted with multiple antennas two-way relays in which primary users (PUs) cooperate with cognitive users (CUs) for mutual benefits. In this context, the problem of both bandwidth and power allocation is investigated. We propose that the CUs are allowed to allocate a part of the PUs spectrum to perform their cognitive transmission. In return, acting as amplify-and-forward two-way relays, they are exploited to support PUs to reach their target data rates over the remaining bandwidth. Power expressions for optimal transmit power allocated per PU and CU antenna are derived under primary quality-of-service constraint in addition to bandwidth and power budget constraints. More specifically, CUs act as relays for the PUs transmission and gain some spectrum as long as they respect these constraints. After deriving the optimal transmit powers, we employ a strong optimization tool based on swarm intelligence to optimize the full and complex relay amplification gain matrices in addition to the bandwidths released to primary and cognitive transmission. Furthermore, three different utility functions are considered in our optimization problems depending on the level of fairness among CUs.

  14. User Multiplexing in Relay Enhanced LTE-Advanced Networks

    DEFF Research Database (Denmark)

    Teyeb, Oumer Mohammed; Frederiksen, Frank; Redana, Simone

    2010-01-01

    is radio relaying. This uses relay nodes that act as surrogate base stations for mobile users whose radio links with the base stations are not experiencing good enough conditions. In the downlink, the data that is destined for the relayed users may first have to be multiplexed by the base station, sent...... over the wireless backhaul link towards the relay node, and de-multiplexed and forwarded to the individual users by the relay node. The reverse process also has to be undertaken in the uplink. In this paper, we present a novel multiplexing scheme which is able to adapt the addressing and bitmapping...... of user identification to the actual number of users being served by the relay nodes, and thus greatly reduce the multiplexing overhead....

  15. Performance Evaluation of Relay Selection Schemes in Beacon-Assisted Dual-Hop Cognitive Radio Wireless Sensor Networks under Impact of Hardware Noises.

    Science.gov (United States)

    Hieu, Tran Dinh; Duy, Tran Trung; Dung, Le The; Choi, Seong Gon

    2018-06-05

    To solve the problem of energy constraints and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive the exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

  16. Relay race

    CERN Multimedia

    Staff Association

    2011-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

  17. Relay race

    CERN Document Server

    Staff Association

    2011-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12·15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

  18. Resource allocation for relay assisted cognitive radio networks

    KAUST Repository

    Zafar, Ammar; Alouini, Mohamed-Slim; Chen, Yunfei; Radaydeh, Redha M.

    2012-01-01

    transmission power and the relay transmission power. Numerical results show that the optimal sensing time is dependent on the primary user's signal-to-noise-ratio (SNR). They also show that SCR increases with increase in the number of relays. © 2012 IEEE.

  19. Relay-assited transmission and radio resource management for wireless networks

    OpenAIRE

    Agustín de Dios, Adrián

    2008-01-01

    La transmisión asistida por relay o transmisión cooperativa es una nueva técnica de diversidad espacial donde aparece un elemento nuevo (un relay o un usuario cooperativo) en la tradicional transmisión punto a punto (fuente a destino). Ahora en la comunicación intervienen tres enlaces: fuente-relay, relay-destino y fuente-destino. El relay, además de asistir a la fuente en la transmisión de un mensaje, permite combatir las degradaciones que puede sufrir el canal como el shadowing y el pathlos...

  20. An RSS based location estimation technique for cognitive relay networks

    KAUST Repository

    Qaraqe, Khalid A.; Hussain, Syed Imtiaz; Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Alouini, Mohamed-Slim

    2010-01-01

    In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine

  1. Interference Neutralization vs Clean Relaying in Cognitive Radio Networks with Secrecy

    Directory of Open Access Journals (Sweden)

    Pin-Hsun Lin

    2015-08-01

    Full Text Available In this paper we study cognitive radio networks with secrecy constraints on the primary transmission. In particular we consider several transmission schemes for the secondary transmitter, namely interference neutralization (IN and cooperative jamming with and without clean relaying (CR. We derive and analyze the achievable secondary rate performance of the schemes. Furthermore we thoroughly investigate the advantages and shortcomings of these schemes through numerical simulations in a geometric model where we highlight the impact of the users’ locations and show the important difference in all schemes depending on the topology. Our results show that the secondary transmitter can successfully adapt its transmission scheme (and parameters, i.e., either IN or CR, depending on its location to maximize its rate while insuring perfect secrecy of the primary transmission.

  2. Handover Framework for Relay Enhanced LTE Networks

    DEFF Research Database (Denmark)

    Teyeb, Oumer Mohammed; Van Phan, Vinh; Raaf, Bernhard

    2009-01-01

    Relaying is one of the proposed technologies for future releases of UTRAN Long Term Evolution (LTE) networks. Introducing relaying is expected to increase the coverage and capacity of LTE networks. In order to enable relaying, the architecture, protocol and radio resource management procedures...... of LTE, such as handover, have to be modified. A user can be handed over not only between two base stations, but also between relays and base stations, and between two relays. With the introduction of relaying, there is a need for a new procedure to hand over a relay and all its associated users...... to another base station, allowing a flexible and dynamic relay deployment. In this paper, we extend the LTE release 8 handover mechanisms so that it can accommodate these new handover functionalities in a flexible manner....

  3. Overlay cognitive radio systems with adaptive two-way relaying

    KAUST Repository

    Hyadi, Amal

    2013-12-01

    In this paper, we propose a spectrum sharing mechanism with a two-phase two-way relaying protocol for an overlay cognitive network. The system comprises two primary users (PUs) and two secondary users (SUs). One of the SUs acts as a relay for the PUs and gains spectrum sharing as long as he respects outage probability constraints of the primary system. Moreover, we consider that the relaying node performs an optimal power allocation scheme that minimizes the outage performance of the secondary receiver. Closed form expressions for the outage probability are derived for the cases of Decode-and-Forward (DF), Amplify-and-Forward (AF), and adaptive relaying. Numerical simulations are presented to illustrate and compare the obtained results. © 2013 IEEE.

  4. Spectral efficiency enhancement with interference cancellation for wireless relay network

    DEFF Research Database (Denmark)

    Yomo, Hiroyuki; De Carvalho, Elisabeth

    The introduction of relaying into wireless communication system for coverage enhancement can cause severe decrease of spectral efficiency due to the requirement on extra radio resource. In this paper, we propose a method to increase spectral efficiency in such a wireless relay network by employing...... an interference cancellation technique. We focus on a typical scenario of relaying in a cellular system, where a mobile station (MS) requires the help of a relay station (RS) to communicate with the base station (BS). In such a case, interference cancellation can be used to achieve a small reuse distance...... of identical radio resource. We analyze a simple scenario with BS, single RS, and 2 MSs, and show that the proposed method has significant potential to enhance spectral efficiency in wireless relay networks....

  5. CERN Relay Race

    CERN Document Server

    2008-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 5 June starting at 12:15 p.m. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

  6. CERN Relay Race

    CERN Document Server

    2007-01-01

    The CERN relay race will take place around the Meyrin site on Wednesday 23 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

  7. CERN Relay Race

    CERN Document Server

    CERN Running Club

    2010-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 20 May, starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the route, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay

  8. Optimal relay selection and power allocation for cognitive two-way relaying networks

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2012-06-01

    In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays. The secondary nodes share the spectrum with a licensed primary user (PU), and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. We propose joint relay selection and optimal power allocation among the secondary user (SU) nodes achieving maximum throughput under transmit power and PU interference constraints. A closed-form solution for optimal allocation of transmit power among the SU transceivers and the SU relay is presented. Furthermore, numerical simulations and comparisons are presented to illustrate the performance of the proposed scheme. © 2012 IEEE.

  9. Strategies for improvement of spectrum capacity for WiMax cellular systems by Cognitive Radio Technology supported by Relay Stations

    DEFF Research Database (Denmark)

    Frederiksen, Flemming Bjerge; Prasad, Ramjee

    2007-01-01

    Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context will be presented and discussed in this paper. Ideas to improve the wireless transmission by orthogonal OFDM-based communication and to increase...... the coverage of cellular systems by relay stations will be presented as well.   ...

  10. Resource allocation for relay assisted cognitive radio networks

    KAUST Repository

    Zafar, Ammar

    2012-09-16

    In this paper, we present two optimal resource allocation schemes that maximize throughput and symbol correct rate (SCR). The throughput and SCR are derived. The derived throughput and SCR are optimized with respect to the sensing time, the source transmission power and the relay transmission power. Numerical results show that the optimal sensing time is dependent on the primary user\\'s signal-to-noise-ratio (SNR). They also show that SCR increases with increase in the number of relays. © 2012 IEEE.

  11. Dynamic Relaying in 3GPP LTE-Advanced Networks

    DEFF Research Database (Denmark)

    Teyeb, Oumer Mohammed; Van Phan, Vinh; Redana, Simone

    2009-01-01

    Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while...... maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying.With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning....... Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can...

  12. CERN Relay Race

    CERN Document Server

    2006-01-01

    The CERN relay race will take place around the Meyrin site on Wednesday 17 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site.

  13. Cognitive Spectrum Efficient Multiple Access Technique using Relay Systems

    DEFF Research Database (Denmark)

    Frederiksen, Flemming Bjerge; Prasad, Ramjee

    2007-01-01

    Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context will be presented and discussed in this paper. Ideas to increase the coverage of cellular systems by relay channels, relay stations and collaborate...

  14. Dynamic Relaying in 3GPP LTE-Advanced Networks

    Directory of Open Access Journals (Sweden)

    Van Phan Vinh

    2009-01-01

    Full Text Available Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying. With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning. Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can be either between different base stations or even between different networks.

  15. Frame Allocation and Scheduling for Relay Networks in the LTE Advanced Standard

    OpenAIRE

    Roth, Stefan

    2010-01-01

    The use of relays is seen as a promising way to extend cell coverage and increase rates in LTE Advanced networks. Instead of increasing the number of base stations (BS), relays with lower cost could provide similar gains. A relay will have a wireless link to the closest BS as only connection to the core network and will cover areas close to the cell edge or other areas with limited rates. Performing transmissions in several hops (BS-relay & relay-user) requires more radio resources than u...

  16. Distributed cognitive two-way relay beamformer designs under perfect and imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla; Aissa, Sonia

    2011-01-01

    In this paper, we present distributed two-way relay beamformer designs for a cognitive radio network (CRN) in which a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relay nodes

  17. CERN Relay Race 2009

    CERN Document Server

    2009-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 14th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. More details on how to register your team for the relay race

  18. CERN Relay Race

    CERN Multimedia

    2011-01-01

    The CERN relay race will take place around the Meyrin site on Thursday 19 May starting at 12-15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details of the course and of how to register your team for the relay race can be found here. Some advice for all runners from the Medical Service can also be found here.   

  19. An RSS based location estimation technique for cognitive relay networks

    KAUST Repository

    Qaraqe, Khalid A.

    2010-11-01

    In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine the location of the source using the direct and the relayed signal at the destination. We derive the Cramer-Rao lower bound (CRLB) expressions separately for x and y coordinates of the location estimate. We analyze the effects of cognitive behaviour of the relay on the performance of the proposed method. We also discuss and quantify the reliability of the location estimate using the proposed technique if the source is not stationary. The overall performance of the proposed method is presented through simulations. ©2010 IEEE.

  20. New resource allocation scheme for cognitive relay networks with opportunistic access

    KAUST Repository

    Zafar, Ammar

    2012-06-01

    In this paper, a new resource allocation scheme to minimize Symbol Error rate (SER) for relay assisted cognitive radio networks is studied. A cognitive relay network with amplify-and-forward (AF) fixed gain relays and opportunistic access to the licensed spectrum is considered. The SER objective function and the optimization constraints are derived first. The resource allocation algorithm is then derived using the Langrangian multiplier method. Closed form expressions are derived for the source and relay powers and, symbol time. Analytical results show that the optimal power allocation follows an extended water-filling solution. © 2012 IEEE.

  1. Energy-Efficient Relay Selection Scheme for Physical Layer Security in Cognitive Radio Networks

    Directory of Open Access Journals (Sweden)

    Li Jiang

    2015-01-01

    selection and dynamic power allocation in order to maximize SC and to minimize energy consumption. Moreover, we consider finite-state Markov channels and residual relay energy in the relay selection and power allocation process. Specifically, the formulation of the proposed relay selection and power allocation scheme is based on the restless bandit problem, which is solved by the primal-dual index heuristic algorithm. Additionally, the obtained optimal relay selection policy has an indexability property that dramatically reduces the computational complexity. Numerical results are presented to show that our proposed scheme has the maximum SC and minimum energy consumption compared to the existing ones.

  2. Robust distributed cognitive relay beamforming

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2012-05-01

    In this paper, we present a distributed relay beamformer design for a cognitive radio network in which a cognitive (or secondary) transmit node communicates with a secondary receive node assisted by a set of cognitive non-regenerative relays. The secondary nodes share the spectrum with a licensed primary user (PU) node, and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. The proposed robust cognitive relay beamformer design seeks to minimize the total relay transmit power while ensuring that the transceiver signal-to-interference- plus-noise ratio and PU interference constraints are satisfied. The proposed design takes into account a parameter of the error in the channel state information (CSI) to render the performance of the beamformer robust in the presence of imperfect CSI. Though the original problem is non-convex, we show that the proposed design can be reformulated as a tractable convex optimization problem that can be solved efficiently. Numerical results are provided and illustrate the performance of the proposed designs for different network operating conditions and parameters. © 2012 IEEE.

  3. Ultra Reliable Short Message Relaying with Wireless Power Transfer

    OpenAIRE

    López, Onel L. Alcaraz; Alves, Hirley; Souza, Richard Demo; Fernández, Evelio Martín García

    2017-01-01

    Abstract We consider a dual-hop wireless network where an energy constrained relay node first harvests energy through the received radio-frequency signal from the source, and then uses the harvested energy to forward the source’s information to the destination node. The throughput and delay metrics are investigated for a decode-and-forward relaying mechanism at finite blocklength regime and delay-limited transmission mode. We consider ultra-reliable communication scenarios under discussio...

  4. Joint Spectrum Sensing and Resource Allocation for OFDM-based Transmission with a Cognitive Relay

    Directory of Open Access Journals (Sweden)

    S. Eman Mahmoodi

    2014-04-01

    Full Text Available In this paper, we investigate the joint spectrum sensing and resource allocation problem to maximize throughput capacity of an OFDM-based cognitive radio link with a cognitive relay. By applying a cognitive relay that uses decode and forward (D&F, we achieve more reliable communications, generating less interference (by needing less transmit power and more diversity gain. In order to account for imperfections in spectrum sensing, the proposed schemes jointly modify energy detector thresholds and allocates transmit powers to all cognitive radio (CR subcarriers, while simultaneously assigning subcarrier pairs for secondary users (SU and the cognitive relay. This problem is cast as a constrained optimization problem with constraints on (1 interference introduced by the SU and the cognitive relay to the PUs; (2 miss-detection and false alarm probabilities and (3 subcarrier pairing for transmission on the SU transmitter and the cognitive relay and (4 minimum Quality of Service (QoS for each CR subcarrier. We propose one optimal and two suboptimal schemes all of which are compared to other schemes in the literature. Simulation results show that the proposed schemes achieve significantly higher throughput than other schemes in the literature for different relay situations.

  5. RADIO EMISSION FROM ACCELERATION SITES OF SOLAR FLARES

    International Nuclear Information System (INIS)

    Li Yixuan; Fleishman, Gregory D.

    2009-01-01

    This Letter takes up the question of what radio emission is produced by electrons at the very acceleration site of a solar flare. Specifically, we calculate incoherent radio emission produced within two competing acceleration models-stochastic acceleration by cascading MHD turbulence and regular acceleration in collapsing magnetic traps. Our analysis clearly demonstrates that radio emission from acceleration sites (1) has sufficiently strong intensity to be observed by currently available radio instruments, and (2) has spectra and light curves that are distinctly different in these two competing models, which makes them observationally distinguishable. In particular, we suggest that some of the narrowband microwave and decimeter continuum bursts may be a signature of the stochastic acceleration in solar flares.

  6. Radio Frequency Interference Site Survey for Thai Radio Telescopes

    Science.gov (United States)

    Jaroenjittichai, P.; Punyawarin, S.; Singwong, D.; Somboonpon, P.; Prasert, N.; Bandudej, K.; Kempet, P.; Leckngam, A.; Poshyachinda, S.; Soonthornthum, B.; Kramer, B.

    2017-09-01

    Radio astronomical observations have increasingly been threaten by the march of today telecommunication and wireless technology. Performance of radio telescopes lies within the fact that astronomical sources are extremely weak. National Astronomy Research Institute of Thailand (NARIT) has initiated a 5-year project, known as the Radio Astronomy Network and Geodesy for Development (RANGD), which includes the establishment of 40-meter and 13-meter radio telescopes. Possible locations have been narrowed down to three candidates, situated in the Northern part of Thailand, where the atmosphere is sufficiently dry and suitable for 22 and 43 GHz observations. The Radio Frequency Interference (RFI) measurements were carried out with a DC spectrum analyzer and directional antennas at 1.5 meter above ground, from 20 MHz to 6 GHz with full azimuth coverage. The data from a 3-minute pointing were recorded for both horizontal and vertical polarizations, in maxhold and average modes. The results, for which we used to make preliminary site selection, show signals from typical broadcast and telecommunication services and aeronautics applications. The signal intensity varies accordingly to the presence of nearby population and topography of the region.

  7. On achievable rate of two-way relaying cognitive radio with space alignment

    KAUST Repository

    Sboui, Lokman

    2015-09-11

    We study a multiple-antenna two-way relaying (TWR) spectrum sharing system. A space alignment (SA) technique is adopted by the secondary users (SU\\'s) to avoid interference with the primary users (PU\\'s). We derive the optimal power allocation that maximizes the TWR achievable sum-rate of the SU while respecting the total power budget and the relay power constraints. In the numerical results, we quantify the sum-rate gain of using the SA in the TWR CR and we show that the SU sum-rate is very limited when the relay power is low or the PU\\'s power and its resulting interference is high. © 2015 IEEE.

  8. Outage analysis for underlay relay-assisted cognitive networks

    KAUST Repository

    Tourki, Kamel; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

    2012-01-01

    Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

  9. Outage analysis for underlay relay-assisted cognitive networks

    KAUST Repository

    Tourki, Kamel

    2012-12-01

    Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

  10. Joint Subcarrier Pairing and Resource Allocation for Cognitive Network and Adaptive Relaying Strategy

    KAUST Repository

    Soury, Hamza

    2012-05-01

    Recent measurements show that the spectrum is under-utilized by licensed users in wireless communication. Cognitive radio (CR) has been proposed as a suitable solution to manage the inefficient usage of the spectrum and increase coverage area of wireless networks. The concept is based on allowing a group of secondary users (SUs) to share the unused radio spectrum originally owned by the primary user (PUs). The operation of CR should not cause harmful interference to the PUs. In the other hand, relayed transmission increases the coverage and achievable capacity of communication systems and in particular in CR systems. In fact there are many types of cooperative communications, however the two main ones are decode-and-forward (DAF) and amplify-and-forward (AAF). Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. In this dissertation, we investigate the power allocation for an adaptive relaying protocol (ARP) scheme in cognitive system by maximizing the end-to-end rate and searching the best carriers pairing distribution. The optimization problem is under the interference and power budget constraints. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques, and the consequence of the choice of the pairing strategy.

  11. Near optimal power allocation algorithm for OFDM-based cognitive using adaptive relaying strategy

    KAUST Repository

    Soury, Hamza; Bader, Faouzi; Shaat, Musbah M R; Alouini, Mohamed-Slim

    2012-01-01

    Relayed transmission increases the coverage and achievable capacity of communication systems. Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. A cognitive Orthogonal Frequency-Division Multiplexing (OFDM) based adaptive relaying protocol is considered in this paper. The objective is to maximize the capacity of the cognitive radio system while ensuring that the interference introduced to the primary user is below the tolerated limit. A Near optimal power allocation in the source and the relay is presented for two pairing techniques such that the matching and random pairing. The simulation results confirm the efficiency of the proposed adaptive relaying protocol, and the consequence of choice of pairing technique. © 2012 ICST.

  12. Relaying Strategies and Protocols for Efficient Wireless Networks

    KAUST Repository

    Zafar, Ammar

    2014-10-01

    for overlay cognitive radios is derived. This protocol utilizes relays with buffers, requires only causal knowledge of the primary\\'s message at the secondary and incentivizes the primary to cooperate with the secondary and share its codebook.

  13. Cost and Performance Comparison of an Earth-Orbiting Optical Communication Relay Transceiver and a Ground-Based Optical Receiver Subnet

    Science.gov (United States)

    Wilson, K. E.; Wright, M.; Cesarone, R.; Ceniceros, J.; Shea, K.

    2003-01-01

    Optical communications can provide high-data-rate telemetry from deep-space probes with subsystems that have lower mass, consume less power, and are smaller than their radio frequency (RF) counterparts. However, because optical communication is more affected by weather than is RF communication, it requires ground station site diversity to mitigate the adverse effects of inclement weather on the link. An optical relay satellite is not affected by weather and can provide 24-hour coverage of deep-space probes. Using such a relay satellite for the deep-space link and an 8.4-GHz (X-band) link to a ground station would support high-data-rate links from small deep-space probes with very little link loss due to inclement weather. We have reviewed past JPL-funded work on RF and optical relay satellites, and on proposed clustered and linearly dispersed optical subnets. Cost comparisons show that the life cycle costs of a 7-m optical relay station based on the heritage of the Next Generation Space Telescope is comparable to that of an 8-station subnet of 10-m optical ground stations. This makes the relay link an attractive option vis-a-vis a ground station network.

  14. Protective relay

    International Nuclear Information System (INIS)

    Lim, Mu Ji; Jung, Hae Sang

    1974-10-01

    This book is divided into two chapters, which deals with protective relay. The first chapter deals with the basic knowledge of relay on development of relay, classification of protective relay, rating of protective relay general structure of protective relay, detecting of ground protection, about point of contact, operating relay and trip relaying. The second chapter is about structure and explanation of relay on classification by structure such as motor type and moving-coil type, explanation of other relays over current relay, over voltage relay, short voltage relay, relay for power, relay for direction, test of over voltage relay, test of short voltage relay and test of directional circuit relay.

  15. Impact of Primary User Traffic on Adaptive Transmission for Cognitive Radio with Partial Relay Selection

    KAUST Repository

    Rao, Anlei

    2012-09-08

    In a cognitive relay system, the secondary user is permitted to transmit data via a relay when licensed frequency bands are detected to be free. Previous studies mainly focus on reducing or limiting the interference of the secondary transmission on the primary users. On the other hand, however, the primary user traffic will also affect the data transmission performance of the secondary users. In this paper, we investigate the impact of the primary user traffic on the bit error rate (BER) of the secondary transmission, when the secondary user adopts adaptive transmission with a relay partially selected. From the numerical results, we can see that the primary user traffic seriously degrades average BER. The worse-link partial selection can perform almost as well as the global selection when the channel conditions of the source-relay links and the relay-destination links differ a lot. In addition, although the relay selection improves the spectral efficiency of the secondary transmission, numerical results show that it only has slight impact on the overall average BER, so that the robustness of the system will not be affected by the relay selection.

  16. Outage analysis for underlay cognitive networks using incremental regenerative relaying

    KAUST Repository

    Tourki, Kamel; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

    2013-01-01

    Cooperative relay technology has recently been introduced into cognitive radio (CR) networks to enhance the network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where

  17. Analysis of multiuser mixed RF/FSO relay networks for performance improvements in Cloud Computing-Based Radio Access Networks (CC-RANs)

    Science.gov (United States)

    Alimi, Isiaka A.; Monteiro, Paulo P.; Teixeira, António L.

    2017-11-01

    The key paths toward the fifth generation (5G) network requirements are towards centralized processing and small-cell densification systems that are implemented on the cloud computing-based radio access networks (CC-RANs). The increasing recognitions of the CC-RANs can be attributed to their valuable features regarding system performance optimization and cost-effectiveness. Nevertheless, realization of the stringent requirements of the fronthaul that connects the network elements is highly demanding. In this paper, considering the small-cell network architectures, we present multiuser mixed radio-frequency/free-space optical (RF/FSO) relay networks as feasible technologies for the alleviation of the stringent requirements in the CC-RANs. In this study, we use the end-to-end (e2e) outage probability, average symbol error probability (ASEP), and ergodic channel capacity as the performance metrics in our analysis. Simulation results show the suitability of deployment of mixed RF/FSO schemes in the real-life scenarios.

  18. Advanced relay technologies in next generation wireless communications

    CERN Document Server

    Krikidis, Ioannis

    2016-01-01

    This book details the use of the cooperative networks/relaying approach in new and emerging telecommunications technologies such as full-duplex radio, massive multiple-input multiple-output (MIMO), network coding and spatial modulation, and new application areas including visible light communications (VLC), wireless power transfer, and 5G.

  19. On Secrecy Outage of Relay Selection in Underlay Cognitive Radio Networks over Nakagami-m Fading Channels

    KAUST Repository

    Lei, Hongjiang; Zhang, Huan; Ansari, Imran Shafique; Ren, Zhi; Pan, Gaofeng; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, the secrecy outage performance of an underlay cognitive decode-and-forward relay network over independent but not necessarily identical distributed (i.n.i.d) Nakagami-m fading channels is investigated, in which the secondary user transmitter communicates with the secondary destination via relays, and an eavesdropper attempts to overhear the information. Based on whether the channel state information (CSI) of the wiretap links is available or not, we analyze the secrecy outage performance with optimal relay selection (ORS) and suboptimal relay selection (SRS) schemes, and multiple relays combining scheme (MRC) scheme is considered for comparison purpose. The exact and asymptotic closed-form expressions for the secrecy outage probability with three different relay selection schemes are derived and verified by Monte-Carlo simulations. The numerical results illustrate that ORS scheme always outperforms SRS and MRC schemes, and SRS scheme is better than MRC scheme in the lower fading parameters scenario. Furthermore, through asymptotic analysis, we find that these three different schemes achieve the same secrecy diversity order, which is determined by the number of the relays, and the fading parameters of the links among the relays and the destination.

  20. On Secrecy Outage of Relay Selection in Underlay Cognitive Radio Networks over Nakagami-m Fading Channels

    KAUST Repository

    Lei, Hongjiang

    2017-10-02

    In this paper, the secrecy outage performance of an underlay cognitive decode-and-forward relay network over independent but not necessarily identical distributed (i.n.i.d) Nakagami-m fading channels is investigated, in which the secondary user transmitter communicates with the secondary destination via relays, and an eavesdropper attempts to overhear the information. Based on whether the channel state information (CSI) of the wiretap links is available or not, we analyze the secrecy outage performance with optimal relay selection (ORS) and suboptimal relay selection (SRS) schemes, and multiple relays combining scheme (MRC) scheme is considered for comparison purpose. The exact and asymptotic closed-form expressions for the secrecy outage probability with three different relay selection schemes are derived and verified by Monte-Carlo simulations. The numerical results illustrate that ORS scheme always outperforms SRS and MRC schemes, and SRS scheme is better than MRC scheme in the lower fading parameters scenario. Furthermore, through asymptotic analysis, we find that these three different schemes achieve the same secrecy diversity order, which is determined by the number of the relays, and the fading parameters of the links among the relays and the destination.

  1. Optimal transmit power allocation for MIMO two-way cognitive relay networks with multiple relays using AF strategy

    KAUST Repository

    Alsharoa, Ahmad M.

    2014-02-01

    In this letter, we consider a multiple-input multiple-output two-way cognitive radio system under a spectrum sharing scenario, where primary and secondary users operate on the same frequency band. The secondary terminals aims to exchange different messages with each other using multiple relays where each relay employs an amplify-and-forward strategy. The main objective of our work is to maximize the secondary sum rate allowed to share the spectrum with the primary users by respecting a primary user tolerated interference threshold. In this context, we derive an analytical expression of the optimal power allocated to each antenna of the terminals. We then discuss the impact of some system parameters on the performance in the numerical result section. © 2012 IEEE.

  2. CERN Relay Race

    CERN Multimedia

    2004-01-01

    The CERN Relay Race will take place around the Meyrin site on Wednesday 19 May between 12.15 and 12.35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

  3. CERN Relay Race

    CERN Multimedia

    2001-01-01

    The CERN Relay Race will take place around the Meyrin site on Wednesday 23 May between 12:20 and 12:35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please stop until they all have passed. Thank you for your understanding.

  4. On the capacity of multiple cognitive links through common relay under spectrum-sharing constraints

    KAUST Repository

    Yang, Yuli

    2011-06-01

    In this paper, we consider an underlay cognitive relaying network consisting of multiple secondary users and introduce a cooperative transmission protocol using a common relay to help with the communications between all secondary source-destination pairs for higher throughput and lower realization complexity. A whole relay-assisted transmission procedure is composed of multiple access phase and broadcast phase, where the relay is equipped with multiple antennas, and the secondary sources and destinations are single-antenna nodes. Considering the spectrum-sharing constraints on the secondary sources and the relay, we analyze the capacity behaviors of the underlay cognitive relaying network under study. The corresponding numerical results provide a convenient tool for the presented network design and substantiate a distinguishing feature of introduced design in that multiple secondary users\\' communications do not rely on multiple relays, hence allowing for a more efficient use of the radio resources. © 2011 IEEE.

  5. CERN’s annual relay a runaway success

    CERN Document Server

    Klaus Hanke for the CERN Running Club

    2016-01-01

    With a record participation of 128 teams of six runners each, this year’s CERN Relay Race took place on 19 May on the Meyrin site.   One of the many winning teams from the 2016 relay race. (Image: Sophia Bennett/CERN) With a record participation of 128 teams and 768 runners, this year’s CERN Relay Race took place on 19 May on the Meyrin site. The teams were mainly composed of CERN staff or contractors working on the CERN site.  A few external teams took also part in the race. Times ranged from 10 min 19 s to over 18 min. The Running Club website now has both the results, and the photos from race day. The CERN Relay Race is jointly organised every year by the CERN Running Club and the Staff Association. It is a tradition that is appreciated by many as a team building, rather than a competitive event. The CERN Running Club wishes to thank all runners and all volunteers for making this event a success.

  6. Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

    KAUST Repository

    Soury, Hamza; Bader, F.; Shaat, M.; Alouini, Mohamed-Slim

    2013-01-01

    Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

  7. Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

    KAUST Repository

    Soury, Hamza

    2013-11-09

    Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

  8. CERN Relay Race

    CERN Multimedia

    2003-01-01

    The CERN Relay Race will take place around the Meyrin site on Wednesday May 21st between 12h15 and 12h35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

  9. CERN Relay Race

    CERN Document Server

    2002-01-01

    The CERN Relay Race will take place around the Meyrin site on Wednesday 22 May between 12h20 and 12h35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding.

  10. Latest Changes to NASA's Laser Communication Relay Demonstration Project

    Science.gov (United States)

    Edwards, Bernard L.; Israel, David J.; Vithlani, Seema K.

    2018-01-01

    Over the last couple of years, NASA has been making changes to the Laser Communications Relay Demonstration Project (LCRD), a joint project between NASA's Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory, California Institute of Technology (JPL), and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL). The changes made makes LCRD more like a future Earth relay system that has both high speed optical and radio frequency links. This will allow LCRD to demonstrate a more detailed concept of operations for a future operational mission critical Earth relay. LCRD is expected to launch in June 2019 and is expected to be followed a couple of years later with a prototype user terminal on the International Space Station. LCRD's architecture will allow it to serve as a testbed in space and this paper will provide an update of its planned capabilities and experiments.

  11. CERN Relay Race: information for drivers

    CERN Multimedia

    2012-01-01

    The CERN relay race will take place around the Meyrin site on Thursday, 24 May starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. In addition, there will be a Nordic Walking event which will finish around 12.50. This should not block the roads, but please drive carefully during this time. Thank you for your cooperation. Details on how to register your team for the relay race can be found here.

  12. Cognitive two-way relay beamforming: Design with resilience to channel state uncertainties

    KAUST Repository

    Ubaidulla, P.; Alouini, Mohamed-Slim; Aissa, Sonia

    2016-01-01

    In this paper, we propose a robust distributed relay beamformer design for cognitive radio network operating under uncertainties in the available channel state information. The cognitive network consists of a pair of transceivers and a set of non

  13. Two-Way Multiuser Mixed RF/FSO Relaying: Performance Analysis and Power Allocation

    KAUST Repository

    Al-Eryani, Yasser F.; Salhab, Anas; Zummo, Salam A.; Alouini, Mohamed-Slim

    2018-01-01

    In this paper, the performance of two-way multiuser mixed radio frequency/free space optical (RF/FSO) relay networks with opportunistic user scheduling and asymmetric channel fading is studied. RF links are used to conduct data transmission between

  14. Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

    KAUST Repository

    Sungjoon Park,

    2011-11-01

    In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula for opportunistic relaying in the channel, and validate the results by comparing it with the exact outage probability. Also, we suggest a new relay selection algorithm that incorporates shadowing. We consider a protocol of broadcasting the channel gain of the previously selected relay. This saves resources in slow fading channel by reducing collisions in relay selection. We further investigate the optimal relay selection period to maximize the throughput while avoiding selection overhead. © 2011 IEEE.

  15. Technique for determination of the time constant for relay radioisotope instruments

    International Nuclear Information System (INIS)

    Gol'din, M.L.; Shestialtynov, V.K.

    1981-01-01

    A technique for calculating time constant of a gamma relay used in radio isotope automatics is suggested. It is shown that the time constant of a radioisotope relay device (RRD) mainly depends on parameters of the intergrating circuit ratemeter. Considering the ratemeter as a real communication channel with a limited transmission band, the equation for the active front duration at a ratemeter outlet when applying abrupt voltage to its inlet is obtained. From the complex transmission function of a ratemeter the upper boundary cyclic transmission frequency the substitution of which in the equation of the active front durationg ives the RRD time constant is determined. On the example of calculating the ratemeter for the GR-6 gamma relay a satisfactory coincidence of calculational results with the certificate data is shown [ru

  16. Overlay Cognitive Radios With Channel-Aware Adaptive Link Selection and Buffer-Aided Relaying

    KAUST Repository

    Shaqfeh, Mohammad

    2015-08-01

    The aim of this work is to maximize the long-term average achievable rate region of a primary and a secondary source-destination pairs operating in an overlay setup over block-fading channels. To achieve this objective, we propose an opportunistic strategy to grant channel access to the primary and secondary sources based on the channel conditions in order to exploit the available multiple-link diversity gains in the system. The secondary source has causal knowledge of the primary messages and it acts as a relay of the primary source in return for getting access to the channel. To maximize the gains of relaying, the relay and destination are equipped with buffers to enable the use of channel-aware adaptive link selection. We propose and optimize different link selection policies and characterize their expected achievable rates. Also, we provide several numerical results to demonstrate the evident mutual benefits of buffer-aided cooperation and adaptive link selection to the primary and the secondary source-destination pairs. © 1972-2012 IEEE.

  17. Overlay Cognitive Radios With Channel-Aware Adaptive Link Selection and Buffer-Aided Relaying

    KAUST Repository

    Shaqfeh, Mohammad; Zafar, Ammar; Alnuweiri, Hussein; Alouini, Mohamed-Slim

    2015-01-01

    The aim of this work is to maximize the long-term average achievable rate region of a primary and a secondary source-destination pairs operating in an overlay setup over block-fading channels. To achieve this objective, we propose an opportunistic strategy to grant channel access to the primary and secondary sources based on the channel conditions in order to exploit the available multiple-link diversity gains in the system. The secondary source has causal knowledge of the primary messages and it acts as a relay of the primary source in return for getting access to the channel. To maximize the gains of relaying, the relay and destination are equipped with buffers to enable the use of channel-aware adaptive link selection. We propose and optimize different link selection policies and characterize their expected achievable rates. Also, we provide several numerical results to demonstrate the evident mutual benefits of buffer-aided cooperation and adaptive link selection to the primary and the secondary source-destination pairs. © 1972-2012 IEEE.

  18. Simultaneous energy harvesting and information processing in wireless multiple relays with multiple antennas

    Science.gov (United States)

    Albaaj, Azhar; Makki, S. Vahab A.; Alabkhat, Qassem; Zahedi, Abdulhamid

    2017-07-01

    Wireless networks suffer from battery discharging specially in cooperative communications when multiple relays have an important role but they are energy constrained. To overcome this problem, energy harvesting from radio frequency signals is applied to charge the node battery. These intermediate nodes have the ability to harvest energy from the source signal and use the energy harvested to transmit information to the destination. In fact, the node tries to harvest energy and then transmit the data to destination. Division of energy harvesting and data transmission can be done in two algorithms: time-switching-based relaying protocol and power-splitting-based relaying protocol. These two algorithms also can be applied in delay-limited and delay-tolerant transmission systems. The previous works have assumed a single relay for energy harvesting, but in this article, the proposed method is concentrated on improving the outage probability and throughput by using multiple antennas in each relay node instead of using single antenna. According to our simulation results, when using multi-antenna relays, ability of energy harvesting is increased and thus system performance will be improved to great extent. Maximum ratio combining scheme has been used when the destination chooses the best signal of relays and antennas satisfying the required signal-to-noise ratio.

  19. Dual-Hop VLC/RF Transmission System with Energy Harvesting Relay under Delay Constraint

    KAUST Repository

    Rakia, Tamer; Yang, Hong-Chuan; Gebali, Fayez; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, we introduce a dual-hop visible light communication (VLC) / radio frequency (RF) transmission system to extend the coverage of indoor VLC systems. The relay between the two hops is able to harvest light energy from different

  20. Multi-Destination Cognitive Radio Relay Network with SWIPT and Multiple Primary Receivers

    KAUST Repository

    Al-Habob, Ahmed A.; Salhab, Anas M.; Zummo, Salam A.; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, we study the performance of simultaneous wireless information and power transfer (SWIPT) technique in a multi-destination dual-hop underlay cognitive relay network with multiple primary receivers. Information transmission from

  1. Distributed cognitive two-way relay beamformer designs under perfect and imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2011-09-01

    In this paper, we present distributed two-way relay beamformer designs for a cognitive radio network (CRN) in which a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relay nodes. The secondary nodes share the spectrum with a licensed primary user (PU) node, and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. First, we consider relay beamformer designs assuming the availability of perfect channel state information (CSI). For this case, a mean-square error (MSE)-constrained beamformer that minimizes the total relay transmit power, and an MSE-balancing beamformer with a constraint on the total relay transmit power are proposed. Next, we consider relay beamformer designs assuming that the available CSI is imperfect. For this case too, we consider the same problems as those in the case of perfect CSI, and propose beamformer designs that are robust to the errors in the CSI. We show that the proposed designs can be reformulated as convex optimization problems that can be solved efficiently. Through numerical simulations, we illustrate the performance of the proposed designs. © 2011 IEEE.

  2. 75 FR 46854 - Amendment of the Commission's Rules Regarding Amateur Radio Service Communications During...

    Science.gov (United States)

    2010-08-04

    ... Civil Emergency Service (RACES), the Amateur Radio Relay League's Amateur Radio Emergency Service (ARES... nation with Critical Infrastructure and Key Resources (CIKR) as described in the National Infrastructure...

  3. Enhancing Physical Layer Security of Multiuser SIMO Mixed RF/FSO Relay Networks with Multi-Eavesdroppers

    KAUST Repository

    El-Malek, Ahmed H. Abd; Salhab, Anas M.; Zummo, Salam A.; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, we investigate the secrecy performance of multiuser (MU) single-input multiple-output (SIMO) mixed radio frequency (RF)/free space optical (FSO) relay network with opportunistic user scheduling and multiple eavesdropping attacks

  4. Broadcast Reserved Opportunity Assisted Diversity Relaying Scheme and Its Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Xia Chen

    2008-05-01

    Full Text Available Relay-based transmission can over the benefits in terms of coverage extension as well as throughput improvement if compared to conventional direct transmission. In a relay enhanced cellular (REC network, where multiple mobile terminals act as relaying nodes (RNs, multiuser diversity gain can be exploited. We propose an efficient relaying scheme, referred to as Broadcast Reserved Opportunity Assisted Diversity (BROAD for the REC networks. Unlike the conventional Induced Multiuser Diversity Relaying (IMDR scheme, our scheme acquires channel quality information (CQI in which the destined node (DN sends pilots on a reserved radio resource. The BROAD scheme can significantly decrease the signaling overhead among the mobile RNs while achieving the same multiuser diversity as the conventional IMDR scheme. In addition, an alternative version of the BROAD scheme, named as A-BROAD scheme, is proposed also, in which the candidate RN(s feed back partial or full CQI to the base station (BS for further scheduling purpose. The A-BROAD scheme achieves a higher throughput than the BROAD scheme at the cost of extra signalling overhead. The theoretical analysis given in this paper demonstrates the feasibility of the schemes in terms of their multiuser diversity gains in a REC network.

  5. Wireless Powered Relaying Networks Under Imperfect Channel State Information: System Performance and Optimal Policy for Instantaneous Rate

    Directory of Open Access Journals (Sweden)

    D. T. Do

    2017-09-01

    Full Text Available In this investigation, we consider wireless powered relaying systems, where energy is scavenged by a relay via radio frequency (RF signals. We explore hybrid time switching-based and power splitting-based relaying protocol (HTPSR and compare performance of Amplify-and-Forward (AF with Decode-and-Forward (DF scheme under imperfect channel state information (CSI. Most importantly, the instantaneous rate, achievable bit error rate (BER are determined in the closed-form expressions under the impact of imperfect CSI. Through numerical analysis, we evaluate system insights via different parameters such as power splitting (PS and time switching (TS ratio of the considered HTPSR which affect outage performance and BER. It is noted that DF relaying networks outperform AF relaying networks. Besides that, the numerical results are given to prove the optimization problems of PS and TS ratio to obtain optimal instantaneous rate.

  6. Alternate transmission with half-duplex relaying in MIMO interference relay networks

    KAUST Repository

    Park, Seongho

    2013-12-01

    In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups alternately every time phase. Each of the relaying groups has arbitrary number of relays, and each relay operates in half-duplex amplify-and-forward mode. In our scheme, the received signals at the relay nodes consist of desired signals and two different interference signals such as the inter-source interferences and the inter-group interferences which are caused by the phase incoherence of relaying. As such, we propose an iterative interference alignment algorithm to mitigate the interferences. We show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying system in the interference relay channels. © 2013 IEEE.

  7. Alternate MIMO relaying with three AF relays using interference alignment

    KAUST Repository

    Park, Kihong

    2012-06-01

    In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss of capacity pre-log factor 1/2 in half duplex mode, where source transmit message to two relays and the other relay alternately. The inter-relay interference caused by alternate transmission is aligned to make additional degrees of freedom (DOFs). It is shown that the proposed scheme enables us to exploit 3M/4 DOFs compared with the M/2 DOFs of conventional AF relaying. More specifically, suboptimal linear filter designs for a source and three relays are proposed to maximize the achievable sum-rate. We verify using some selected numerical results that the proposed filter designs give significant improvement of the sum-rate over a naive filter and conventional relaying schemes. © 2012 IEEE.

  8. End-to-end performance of cooperative relaying in spectrum-sharing systems with quality of service requirements

    KAUST Repository

    Asghari, Vahid Reza; Aissa, Sonia

    2011-01-01

    We propose adopting a cooperative relaying technique in spectrum-sharing cognitive radio (CR) systems to more effectively and efficiently utilize available transmission resources, such as power, rate, and bandwidth, while adhering to the quality

  9. The Use of Intelligent Relays for the Sewer Cleaning Vehicle Control and Automation

    Directory of Open Access Journals (Sweden)

    O. Chiver

    2012-06-01

    Full Text Available The paper presents the way in which the electrical control and automation system of the 5 mc combined sewer and gully cleaning vehicle equipped by a local company was designed, using the intelligent relay of the easy 700 type of Moeller (Eaton company. The control of all the equipments is performed locally from the control panel and some of them can also by remote controlled by means of the radio waves. The program required by the intelligent relay was created, tested and implemented with the help of the dedicated software easy-soft 6, developed by the manufacturing company.

  10. Opportunistic transmitter selection for selfless overlay cognitive radios

    KAUST Repository

    Shaqfeh, Mohammad; Zafar, Ammar; Alnuweiri, Hussein M.; Alouini, Mohamed-Slim

    2013-01-01

    We propose an opportunistic strategy to grant channel access to the primary and secondary transmitters in causal selfless overlay cognitive radios over block-fading channels. The secondary transmitter helps the primary transmitter by relaying

  11. CERN Relay Race 2018

    CERN Document Server

    CERN Running club

    2018-01-01

    The CERN running club, in collaboration with the Staff Association, is happy to announce the 2018 relay race edition. It will take place on Thursday, May 24th and will consist as every year in a round trip of the CERN Meyrin site in teams of 6 members. It is a fun event, and you do not have to run fast to enjoy it. Registrations will be open from May 1st to May 22nd on the running club web site. All information concerning the race and the registration are available there too: http://runningclub.web.cern.ch/content/cern-relay-race. A video of the previous edition is also available here : http://cern.ch/go/Nk7C. As every year, there will be animations starting at noon on the lawn in front of restaurant 1, and information stands for many CERN associations and clubs will be available. The running club partners will also be participate in the event, namely Berthie Sport, Interfon and Uniqa.

  12. Reactive relay selection in underlay cognitive networks with fixed gain relays

    KAUST Repository

    Hussain, Syed Imtiaz

    2012-06-01

    Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference constraints to the primary users. Generally, relay selection is done on the basis of maximum end-to-end signal to noise ratio (SNR). However, it requires large amounts of channel state information (CSI) at different network nodes. In this paper, we present and analyze a reactive relay selection scheme in underlay cognitive networks where the relays are operating with fixed gains near a primary user. The system model minimizes the amount of CSI required at different nodes and the destination selects the best relay on the basis of maximum relay to destination SNR. We derive close form expressions for the received SNR statistics, outage probability, bit error probability and average channel capacity of the system. Simulation results are also presented to confirm the validity of the derived expressions. © 2012 IEEE.

  13. Outage analysis for underlay cognitive networks using incremental regenerative relaying

    KAUST Repository

    Tourki, Kamel

    2013-02-01

    Cooperative relay technology has recently been introduced into cognitive radio (CR) networks to enhance the network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service (QoS) of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. Analysis is conducted for two schemes, referred to as the channel-state information (CSI)-based and fault-tolerant schemes, respectively, where different amounts of CSI were considered. We first provide the exact cumulative distribution function (cdf) of the received signal-to-noise ratio (SNR) over each hop with colocated relays. Then, the cdf\\'s are used to determine a very accurate closed-form expression for the outage probability for a transmission rate $R$. In a high-SNR region, a floor of the secondary outage probability occurs, and we derive its corresponding expression. We validate our analysis by showing that the simulation results coincide with our analytical results in Rayleigh fading channels. © 1967-2012 IEEE.

  14. Partial relay selection in underlay cognitive networks with fixed gain relays

    KAUST Repository

    Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Hasna, Mazen Omar; Qaraqe, Khalid A.

    2012-01-01

    In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

  15. Partial relay selection in underlay cognitive networks with fixed gain relays

    KAUST Repository

    Hussain, Syed Imtiaz

    2012-05-01

    In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

  16. Opportunistic Relay Selection in Multicast Relay Networks using Compressive Sensing

    KAUST Repository

    Elkhalil, Khalil

    2014-12-01

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. However, for relay selection algorithms to make a selection decision, channel state information (CSI) from all cooperating relays is usually required at a central node. This requirement poses two important challenges. Firstly, CSI acquisition generates a great deal of feedback overhead (air-time) that could result in significant transmission delays. Secondly, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we introduce a limited feedback relay selection algorithm for a multicast relay network. The proposed algorithm exploits the theory of compressive sensing to first obtain the identity of the “strong” relays with limited feedback. Following that, the CSI of the selected relays is estimated using linear minimum mean square error estimation. To minimize the effect of noise on the fed back CSI, we introduce a back-off strategy that optimally backs-off on the noisy estimated CSI. For a fixed group size, we provide closed form expressions for the scaling law of the maximum equivalent SNR for both Decode and Forward (DF) and Amplify and Forward (AF) cases. Numerical results show that the proposed algorithm drastically reduces the feedback air-time and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback channels.

  17. Security-Reliability Trade-Off Analysis for Multiuser SIMO Mixed RF/FSO Relay Networks With Opportunistic User Scheduling

    KAUST Repository

    El-Malek, Ahmed H. Abd; Salhab, Anas M.; Zummo, Salam A.; Alouini, Mohamed-Slim

    2016-01-01

    In this paper, we study the performance of multiuser single-input multiple-output mixed radio frequency (RF)/free space optical (FSO) relay network with opportunistic user scheduling. The considered system includes multiple users, one amplify

  18. Optimized Power Allocation and Relay Location Selection in Cooperative Relay Networks

    Directory of Open Access Journals (Sweden)

    Jianrong Bao

    2017-01-01

    Full Text Available An incremental selection hybrid decode-amplify forward (ISHDAF scheme for the two-hop single relay systems and a relay selection strategy based on the hybrid decode-amplify-and-forward (HDAF scheme for the multirelay systems are proposed along with an optimized power allocation for the Internet of Thing (IoT. Given total power as the constraint and outage probability as an objective function, the proposed scheme possesses good power efficiency better than the equal power allocation. By the ISHDAF scheme and HDAF relay selection strategy, an optimized power allocation for both the source and relay nodes is obtained, as well as an effective reduction of outage probability. In addition, the optimal relay location for maximizing the gain of the proposed algorithm is also investigated and designed. Simulation results show that, in both single relay and multirelay selection systems, some outage probability gains by the proposed scheme can be obtained. In the comparison of the optimized power allocation scheme with the equal power allocation one, nearly 0.1695 gains are obtained in the ISHDAF single relay network at a total power of 2 dB, and about 0.083 gains are obtained in the HDAF relay selection system with 2 relays at a total power of 2 dB.

  19. Threshold-Based Relay Selection for Detect-and-Forward Relaying in Cooperative Wireless Networks

    Directory of Open Access Journals (Sweden)

    Fan Yijia

    2010-01-01

    Full Text Available This paper studies two-hop cooperative demodulate-and-forward relaying using multiple relays in wireless networks. A threshold based relay selection scheme is considered, in which the reliable relays are determined by comparing source-relay SNR to a threshold, and one of the reliable relays is selected by the destination based on relay-destination SNR. The exact bit error rate of this scheme is derived, and a simple threshold function is proposed. It is shown that the network achieves full diversity order ( under the proposed threshold, where is the number of relays in the network. Unlike some other full diversity achieving protocols in the literature, the requirement that the instantaneous/average SNRs of the source-relay links be known at the destination is eliminated using the appropriate SNR threshold.

  20. Cognitive two-way relay beamforming: Design with resilience to channel state uncertainties

    KAUST Repository

    Ubaidulla, P.

    2016-07-26

    In this paper, we propose a robust distributed relay beamformer design for cognitive radio network operating under uncertainties in the available channel state information. The cognitive network consists of a pair of transceivers and a set of non-regenerative two-way relays that assist the communication between the transceiver pair. The secondary nodes share the spectrum with a licensed primary user node while ensuring that the interference to the primary receiver is maintained below a certain threshold. The proposed robust design maximizes the worst-case signal-to-interference-plus-noise ratio at the secondary transceivers while satisfying constraints on the interference to the primary user and on the total relay transmit power. Though the robust design problem is not a convex problem in its original form, we show that it can be reformulated as a convex optimization problem, which can be solved efficiently. Numerical results are provided and illustrate the merits of the proposed design for various operating conditions and parameters. © 2016 IEEE.

  1. Mobile relays for enhanced broadband connectivity in high speed train systems

    KAUST Repository

    Yaacoub, Elias E.

    2014-09-01

    With the introduction of wireless modems and smart phones, the passenger transport industry is witnessing a high demand to ensure not only the safety of the trains, but also to provide users with Internet access all the time inside the train. When the Mobile Terminal (MT) communicates directly with the Base Station (BS), it will experience a severe degradation in the Quality of Service due to the path loss and shadowing effects as the wireless signal is traveling through the train. In this paper, we study the performance in the case of relays placed on top of each train car. In the proposed approach, these relays communicate with the cellular BS on one hand, and with the MTs inside the train cars on the other hand, using the Long Term Evolution (LTE) cellular technology. A low complexity heuristic LTE radio resource management approach is proposed and compared to the Hungarian algorithm, both in the presence and absence of the relays. The presence of the relays is shown to lead to significant enhancements in the effective data rates of the MTs. In addition, the proposed resource management approach is shown to reach a performance close to the optimal Hungarian algorithm. © 2014 Elsevier B.V.

  2. Telecommunications Relay Services

    Science.gov (United States)

    ... Home » Health Info » Hearing, Ear Infections, and Deafness Telecommunications Relay Services On this page: What are telecommunication ... additional information about telecommunication relay services? What are telecommunication relay services? Title IV of the Americans with ...

  3. Reactive relay selection in underlay cognitive networks with fixed gain relays

    KAUST Repository

    Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Hasna, Mazen Omar

    2012-01-01

    Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference

  4. Individual Channel Estimation in a Diamond Relay Network Using Relay-Assisted Training

    Directory of Open Access Journals (Sweden)

    Xianwen He

    2017-01-01

    Full Text Available We consider the training design and channel estimation in the amplify-and-forward (AF diamond relay network. Our strategy is to transmit the source training in time-multiplexing (TM mode while each relay node superimposes its own relay training over the amplified received data signal without bandwidth expansion. The principal challenge is to obtain accurate channel state information (CSI of second-hop link due to the multiaccess interference (MAI and cooperative data interference (CDI. To maintain the orthogonality between data and training, a modified relay-assisted training scheme is proposed to migrate the CDI, where some of the cooperative data at the relay are discarded to accommodate relay training. Meanwhile, a couple of optimal zero-correlation zone (ZCZ relay-assisted sequences are designed to avoid MAI. At the destination node, the received signals from the two relay nodes are combined to achieve spatial diversity and enhanced data reliability. The simulation results are presented to validate the performance of the proposed schemes.

  5. Efficient incremental relaying

    KAUST Repository

    Fareed, Muhammad Mehboob

    2013-07-01

    We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying scheme with both amplify and forward and decode and forward relaying. Numerical results are also presented to verify their analytical counterparts. © 2013 IEEE.

  6. Joint Resource Optimization for Cognitive Sensor Networks with SWIPT-Enabled Relay.

    Science.gov (United States)

    Lu, Weidang; Lin, Yuanrong; Peng, Hong; Nan, Tian; Liu, Xin

    2017-09-13

    Energy-constrained wireless networks, such as wireless sensor networks (WSNs), are usually powered by fixed energy supplies (e.g., batteries), which limits the operation time of networks. Simultaneous wireless information and power transfer (SWIPT) is a promising technique to prolong the lifetime of energy-constrained wireless networks. This paper investigates the performance of an underlay cognitive sensor network (CSN) with SWIPT-enabled relay node. In the CSN, the amplify-and-forward (AF) relay sensor node harvests energy from the ambient radio-frequency (RF) signals using power splitting-based relaying (PSR) protocol. Then, it helps forward the signal of source sensor node (SSN) to the destination sensor node (DSN) by using the harvested energy. We study the joint resource optimization including the transmit power and power splitting ratio to maximize CSN's achievable rate with the constraint that the interference caused by the CSN to the primary users (PUs) is within the permissible threshold. Simulation results show that the performance of our proposed joint resource optimization can be significantly improved.

  7. Distributed Antenna Channels with Regenerative Relaying: Relay Selection and Asymptotic Capacity

    Directory of Open Access Journals (Sweden)

    Aitor del Coso

    2007-11-01

    Full Text Available Multiple-input-multiple-output (MIMO techniques have been widely proposed as a means to improve capacity and reliability of wireless channels, and have become the most promising technology for next generation networks. However, their practical deployment in current wireless devices is severely affected by antenna correlation, which reduces their impact on performance. One approach to solve this limitation is relaying diversity. In relay channels, a set of N wireless nodes aids a source-destination communication by relaying the source data, thus creating a distributed antenna array with uncorrelated path gains. In this paper, we study this multiple relay channel (MRC following a decode-and-forward (D&F strategy (i.e., regenerative forwarding, and derive its achievable rate under AWGN. A half-duplex constraint on relays is assumed, as well as distributed channel knowledge at both transmitter and receiver sides of the communication. For this channel, we obtain the optimum relay selection algorithm and the optimum power allocation within the network so that the transmission rate is maximized. Likewise, we bound the ergodic performance of the achievable rate and derive its asymptotic behavior in the number of relays. Results show that the achievable rate of regenerative MRC grows as the logarithm of the Lambert W function of the total number of relays, that is, 𝒞=log⁡2(W0(N. Therefore, D&F relaying, cannot achieve the capacity of actual MISO channels.

  8. Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

    KAUST Repository

    Sungjoon Park,; Stark, Wayne E.

    2011-01-01

    In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula

  9. Relay Selection for Cooperative Relaying in Wireless Energy Harvesting Networks

    Science.gov (United States)

    Zhu, Kaiyan; Wang, Fei; Li, Songsong; Jiang, Fengjiao; Cao, Lijie

    2018-01-01

    Energy harvesting from the surroundings is a promising solution to provide energy supply and extend the life of wireless sensor networks. Recently, energy harvesting has been shown as an attractive solution to prolong the operation of cooperative networks. In this paper, we propose a relay selection scheme to optimize the amplify-and-forward (AF) cooperative transmission in wireless energy harvesting cooperative networks. The harvesting energy and channel conditions are considered to select the optimal relay as cooperative relay to minimize the outage probability of the system. Simulation results show that our proposed relay selection scheme achieves better outage performance than other strategies.

  10. Outage Performance Analysis of Relay Selection Schemes in Wireless Energy Harvesting Cooperative Networks over Non-Identical Rayleigh Fading Channels.

    Science.gov (United States)

    Do, Nhu Tri; Bao, Vo Nguyen Quoc; An, Beongku

    2016-02-26

    In this paper, we study relay selection in decode-and-forward wireless energy harvesting cooperative networks. In contrast to conventional cooperative networks, the relays harvest energy from the source's radio-frequency radiation and then use that energy to forward the source information. Considering power splitting receiver architecture used at relays to harvest energy, we are concerned with the performance of two popular relay selection schemes, namely, partial relay selection (PRS) scheme and optimal relay selection (ORS) scheme. In particular, we analyze the system performance in terms of outage probability (OP) over independent and non-identical (i.n.i.d.) Rayleigh fading channels. We derive the closed-form approximations for the system outage probabilities of both schemes and validate the analysis by the Monte-Carlo simulation. The numerical results provide comprehensive performance comparison between the PRS and ORS schemes and reveal the effect of wireless energy harvesting on the outage performances of both schemes. Additionally, we also show the advantages and drawbacks of the wireless energy harvesting cooperative networks and compare to the conventional cooperative networks.

  11. Outage Analysis of Cooperative Transmission with Energy Harvesting Relay: Time Switching versus Power Splitting

    Directory of Open Access Journals (Sweden)

    Guanyao Du

    2015-01-01

    Full Text Available This paper investigates the multiuser transmission network with an energy harvesting (EH cooperative relay, where a source transmits independent information to multiple destinations with the help of an energy constrained relay. The relay can harvest energy from the radio frequency (RF signals transmitted from the source, and it helps the multiuser transmission only by consuming the harvested energy. By adopting the time switching and the power splitting relay receiver architectures, we firstly propose two protocols, the time switching cooperative multiuser transmission (TSCMT protocol and the power splitting cooperative multiuser transmission (PSCMT protocol, to enable the simultaneous information processing and EH at the relay for the system. To evaluate the system performance, we theoretically analyze the system outage probability for the two proposed protocols and then derive explicit expressions for each of them, respectively. Numerical results are provided to demonstrate the accuracy of our analytical results and reveal that compared with traditional noncooperative scheme our proposed protocols are green solutions to offer reliable communication and lower system outage probability without consuming additional energy. In particular, for the same transmit power at the source, the PSCMT protocol is superior to the TSCMT protocol to obtain lower system outage probability.

  12. Joint source and relay optimization for interference MIMO relay networks

    Science.gov (United States)

    Khandaker, Muhammad R. A.; Wong, Kai-Kit

    2017-12-01

    This paper considers multiple-input multiple-output (MIMO) relay communication in multi-cellular (interference) systems in which MIMO source-destination pairs communicate simultaneously. It is assumed that due to severe attenuation and/or shadowing effects, communication links can be established only with the aid of a relay node. The aim is to minimize the maximal mean-square-error (MSE) among all the receiving nodes under constrained source and relay transmit powers. Both one- and two-way amplify-and-forward (AF) relaying mechanisms are considered. Since the exactly optimal solution for this practically appealing problem is intractable, we first propose optimizing the source, relay, and receiver matrices in an alternating fashion. Then we contrive a simplified semidefinite programming (SDP) solution based on the error covariance matrix decomposition technique, avoiding the high complexity of the iterative process. Numerical results reveal the effectiveness of the proposed schemes.

  13. Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

    KAUST Repository

    Park, Seongho; Park, Kihong; Ko, Youngchai; Alouini, Mohamed-Slim

    2012-01-01

    In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

  14. Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

    KAUST Repository

    Park, Seongho

    2012-09-01

    In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

  15. CERN Relay Race

    CERN Multimedia

    Running Club

    2010-01-01

    This year’s CERN Relay Race will take place around the Meyrin site on Thursday 20th May at 12h00. This annual event is for teams of 6 runners covering distances of 1000m, 800m, 800m, 500m, 500m and 300m respectively. Teams may be entered in the Seniors, Veterans, Ladies, Mixed or Open categories. The registration fee is 10 CHF per runner, and each runner receives a souvenir prize. As usual, there will be a programme of entertainments from 12h in the arrival area, in front of the Restaurant no. 1. Drinks, food, CERN club information and music will be available for the pleasure of both runners and spectators. The race starts at 12h15, with results and prize giving at 13:15.   For details of the race, and of how to sign up a team, please visit: https://espace.cern.ch/Running-Club/CERN-Relay The event is organised by the CERN Running Club with the support of the CERN Staff Association.  

  16. Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Optical and Microwave Communications

    Science.gov (United States)

    Israel, David J.; Shaw, Harry

    2018-01-01

    NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available.In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

  17. Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Microwave and Optical Communications

    Science.gov (United States)

    Israel, David J.

    2018-01-01

    NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available. In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

  18. Outage Performance Analysis of Relay Selection Schemes in Wireless Energy Harvesting Cooperative Networks over Non-Identical Rayleigh Fading Channels †

    Science.gov (United States)

    Do, Nhu Tri; Bao, Vo Nguyen Quoc; An, Beongku

    2016-01-01

    In this paper, we study relay selection in decode-and-forward wireless energy harvesting cooperative networks. In contrast to conventional cooperative networks, the relays harvest energy from the source’s radio-frequency radiation and then use that energy to forward the source information. Considering power splitting receiver architecture used at relays to harvest energy, we are concerned with the performance of two popular relay selection schemes, namely, partial relay selection (PRS) scheme and optimal relay selection (ORS) scheme. In particular, we analyze the system performance in terms of outage probability (OP) over independent and non-identical (i.n.i.d.) Rayleigh fading channels. We derive the closed-form approximations for the system outage probabilities of both schemes and validate the analysis by the Monte-Carlo simulation. The numerical results provide comprehensive performance comparison between the PRS and ORS schemes and reveal the effect of wireless energy harvesting on the outage performances of both schemes. Additionally, we also show the advantages and drawbacks of the wireless energy harvesting cooperative networks and compare to the conventional cooperative networks. PMID:26927119

  19. Coordinated Direct and Relay Transmission with Linear Non-Regenerative Relay Beamforming

    DEFF Research Database (Denmark)

    Sun, Fan; De Carvalho, Elisabeth; Popovski, Petar

    2012-01-01

    Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying, but also more general traffic scenarios, such as coordinated direct and relay (CDR) transmissions. In a CDR scheme the relay has a central...... role in managing the interference and boosting the overall system performance. In this letter we consider the case in which an amplify-and-forward relay has multiple antennas and can use beamforming to support the coordinated transmissions. We focus on one representative traffic type with one uplink...... user and one downlink user. Two different criteria for relay beamforming are analyzed: maximal weighted sum-rate and maximization of the worst-case weighted SNR. We propose iterative optimal solutions, as well as low-complexity near-optimal solutions....

  20. Radioisotope relay instrument

    International Nuclear Information System (INIS)

    Pozdnyakov, V.N.; Sazonov, O.L.; Taksar, I.M.; Tesnavs, Eh.R.; Yanushkovskij, V.A.

    1974-01-01

    The paper describes a radioisotope relay device containing a radiation source, a detector, an electronic relay block with a comparative threshold mechanism. The device differs from previously known ones in that, for the purpose of increasing stability and speed of action, the electronic relay block is a separate unit and contains two threshold pulse generators which are joined up, across series-connected ''and'' and ''or'' elements, with one of the inputs of the comparative threshold mechanism, whose second input is connected with a detector and whose outputs are connected with a relay element connected by feedback with the above-mentioned ''and'' elements. (author)

  1. Radio-anatomy Atlas for delineation SIRIADE web site: features and 1 year results

    International Nuclear Information System (INIS)

    Denisa, F.; Pointreau, Y.

    2010-01-01

    3-D conformal radiotherapy is based on accurate target volumes delineation. Radio-anatomy knowledge's are useful but sometimes difficult to obtain. Moreover, the sources of recommendations for volume definition are disparate. We thus developed a free radio-anatomy web site dedicated to volumes delineation for radiation-oncologists (www.siriade.org). This web site is a search engine allowing to access to delineation characteristics of main tumours illustrated with clinical cases. It does not aim to provide guidelines. Its main purpose is to provide an iconographic training support with frequent up-datings. We present the features of this web site and one year connexion statistics. (authors)

  2. Enhancing Physical Layer Security of Multiuser SIMO Mixed RF/FSO Relay Networks with Multi-Eavesdroppers

    KAUST Repository

    El-Malek, Ahmed H. Abd

    2017-02-09

    In this paper, we investigate the secrecy performance of multiuser (MU) single-input multiple-output (SIMO) mixed radio frequency (RF)/free space optical (FSO) relay network with opportunistic user scheduling and multiple eavesdropping attacks. The considered system includes multiple users, one amplify-and-froward (AF) relay, one destination and multiple eavesdroppers. The users are connected with a multi-antenna relay through RF links and the relay is connected with the destination through an FSO link. Maximal ratio combining (MRC) scheme is used at the relay node to combine the received signals at its different antennas. The RF/FSO channels are assumed to follow Nakagami-m/Gamma-Gamma fading models with considering the effect of pointing errors. In particular, we derive closed- form expressions for the exact and asymptotic outage probabilities. The asymptotic outage results are then used to obtain the optimal RF transmission power based on the dominant link between the RF and FSO links. Then, the considered system secrecy performance is investigated in the presence of multi- eavesdroppers where exact closed-form expression for the intercept probability is derived. Finally, a cooperative jamming model is proposed along with power allocation to enhance the system secrecy performance. Monte-Carlo simulations are provided to validate the achieved exact and asymptotic results.

  3. Radio-anatomy Atlas for delineation SIRIADE web site: features and 1 year results; Site de radio-anatomie et d'aide a la delineation (SIRIADE): presentation et bilan a un an

    Energy Technology Data Exchange (ETDEWEB)

    Denisa, F. [Centre Jean-Bernard, Clinique Victor-Hugo, 72 - Le Mans (France); Pointreau, Y. [Clinique d' oncologie radiotherapie, Centre Henry-S.-Kaplan, CHU Bretonneau, 37 - Tours (France)

    2010-07-01

    3-D conformal radiotherapy is based on accurate target volumes delineation. Radio-anatomy knowledge's are useful but sometimes difficult to obtain. Moreover, the sources of recommendations for volume definition are disparate. We thus developed a free radio-anatomy web site dedicated to volumes delineation for radiation-oncologists (www.siriade.org). This web site is a search engine allowing to access to delineation characteristics of main tumours illustrated with clinical cases. It does not aim to provide guidelines. Its main purpose is to provide an iconographic training support with frequent up-datings. We present the features of this web site and one year connexion statistics. (authors)

  4. On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

    KAUST Repository

    Park, Kihong

    2012-03-01

    In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity pre-log factor of 1/2 due to half-duplex relaying, we propose a new transmission protocol which combines alternate relaying and inter-relay interference alignment. We prove that the proposed scheme can (i) exploits M degrees of freedom (DOFs) and (ii) perfectly recover the pre-log factor loss if the number of relays is at least six. From our selected numerical results, we show that our proposed scheme gives significant improvement over conventional AF relaying which offers only M/2 DOFs. © 2012 IEEE.

  5. Monitoring an in-situ uranium mining site with radio tomography

    International Nuclear Information System (INIS)

    Stolarczyk, L.; Mondt, W.; Mays, W.

    1991-01-01

    A field test site has been developed to monitor ground water restoration in an in-situ uranium mining project. Uranium deposited in a shallow buried fluvial sandstone channel (aquifer) has been mined by the injection and recovery of ammonia carbonate leachant from a constellation of drillholes. Ground water restoration is accomplished by injecting clean water into a well and recovering contaminated water from companion wells. The restoration process exchanges clean water for contaminated water in the aquifer. The stratigraphic cross section of the aquifer and the hydro-dynamics of the ground water restoration process is currently being investigated with radio wave tomography. Crosshole continuous wave (CW) radio signals are propagated from a well to a second well in the constellation of drillholes. The magnitude and phase of the radio wave are measured in the second well with Radio Imaging Method (RIM) instruments. The acquired data is processed in tomography algorithms to determine the EM wave propagation constants (attenuation rate [α] and phase constant [β]) in each pixel that covers the image plane between wells. The in-situ electrical conductivity values are computed from the pixel propagation constants. Contaminated ground water causes the conductivity of the local zone of the aquifer to increase. This paper describes the initial radio tomography mapping of the deposit lithology and compares radio tomography and E log conductivity values

  6. Advanced Strategic and Tactical Relay Request Management for the Mars Relay Operations Service

    Science.gov (United States)

    Allard, Daniel A.; Wallick, Michael N.; Gladden, Roy E.; Wang, Paul; Hy, Franklin H.

    2013-01-01

    This software provides a new set of capabilities for the Mars Relay Operations Service (MaROS) in support of Strategic and Tactical relay, including a highly interactive relay request Web user interface, mission control over relay planning time periods, and mission management of allowed strategic vs. tactical request parameters. Together, these new capabilities expand the scope of the system to include all elements critical for Tactical relay operations. Planning of replay activities spans a time period that is split into two distinct phases. The first phase is called Strategic, which begins at the time that relay opportunities are identified, and concludes at the point that the orbiter generates the flight sequences for on board execution. Any relay request changes from this point on are called Tactical. Tactical requests, otherwise called Orbit - er Relay State Changes (ORSC), are highly restricted in terms of what types of changes can be made, and the types of parameters that can be changed may differ from one orbiter to the next. For example, one orbiter may be able to delay the start of a relay request, while another may not. The legacy approach to ORSC management involves exchanges of e-mail with "requests for change" and "acknowledgement of approval," with no other tracking of changes outside of e-mail folders. MaROS Phases 1 and 2 provided the infrastructure for strategic relay for all supported missions. This new version, 3.0, introduces several capabilities that fully expand the scope of the system to include tactical relay. One new feature allows orbiter users to manage and "lock" Planning Periods, which allows the orbiter team to formalize the changeover from Strategic to Tactical operations. Another major feature allows users to interactively submit tactical request changes via a Web user interface. A third new feature allows orbiter missions to specify allowed tactical updates, which are automatically incorporated into the tactical change process

  7. Performance Analysis of Relays in LTE for a Realistic Suburban Deployment Scenario

    DEFF Research Database (Denmark)

    Coletti, Claudio; Mogensen, Preben; Irmer, Ralf

    2011-01-01

    Relays are likely to play an important role in the deployment of Beyond 3G networks, such as LTE-Advanced, thanks to the possibility of effectively extending Macro network coverage and fulfilling the expected high data-rate requirements. Up until now, the relay technology potential and its cost......-effectiveness have been widely investigated in the literature, considering mainly statistical deployment scenarios, like regular networks with uniform traffic distribution. This paper is envisaged to illustrate the performances of different relay technologies (In-Band/Out-band) in a realistic suburban network...... scenario with real Macro site positions, user density map and spectrum band availability. Based on a proposed heuristic deployment algorithm, results show that deploying In-band relays can significantly reduce the user outage if high backhaul link quality is ensured, whereas Out-band relaying and the usage...

  8. CERN Relay Race

    CERN Document Server

    2005-01-01

    The CERN Relay Race will take place around the Meyrin site on Wednesday 18 May between 12.15 and 12.35. This year, weather permitting, there will be some new attractions in the start/finish area on the field behind the Main Building. You will be able to: listen to music played by the CERN Jazz Club; buy drinks at the bar organised by the CERN Running Club; buy lunch served directly on the terrace by the restaurant Novae. ATTENTION: concerning traffic, the recommendations are the same as always: If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding.

  9. Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2011-11-01

    In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations. © 2011 IEEE.

  10. Cognitive relaying and power allocation under channel state uncertainties

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2013-04-01

    In this paper, we present robust joint relay precoder designs and transceiver power allocations for a cognitive radio network under imperfect channel state information (CSI). The secondary (or cognitive) network consists of a pair of single-antenna transceiver nodes and a non-regenerative two-way relay with multiple antennas which aids the communication process between the transceiver pair. The secondary nodes share the spectrum with a licensed primary user (PU) while guaranteeing that the interference to the PU receiver is maintained below a specified threshold. We consider two robust designs: the first is based on the minimization of the total transmit power of the secondary relay node required to provide the minimum quality of service, measured in terms of mean-square error (MSE) of the transceiver nodes, and the second is based on the minimization of the sum-MSE of the transceiver nodes. The robust designs are based on worst-case optimization and take into account known parameters of the error in the CSI to render the performance immune to the presence of errors in the CSI. Though the original problem is non-convex, we show that the proposed designs can be reformulated as tractable convex optimization problems that can be solved efficiently. We illustrate the performance of the proposed designs through some selected numerical simulations. © 2013 IEEE.

  11. Optimizing Cooperative Cognitive Radio Networks with Opportunistic Access

    KAUST Repository

    Zafar, Ammar; Alouini, Mohamed-Slim; Chen, Yunfei; Radaydeh, Redha M.

    2012-01-01

    Optimal resource allocation for cooperative cognitive radio networks with opportunistic access to the licensed spectrum is studied. Resource allocation is based on minimizing the symbol error rate at the receiver. Both the cases of all-participate relaying and selective relaying are considered. The objective function is derived and the constraints are detailed for both scenarios. It is then shown that the objective functions and the constraints are nonlinear and nonconvex functions of the parameters of interest, that is, source and relay powers, symbol time, and sensing time. Therefore, it is difficult to obtain closed-form solutions for the optimal resource allocation. The optimization problem is then solved using numerical techniques. Numerical results show that the all-participate system provides better performance than its selection counterpart, at the cost of greater resources. © 2012 Ammar Zafar et al.

  12. Optimizing Cooperative Cognitive Radio Networks with Opportunistic Access

    KAUST Repository

    Zafar, Ammar

    2012-09-16

    Optimal resource allocation for cooperative cognitive radio networks with opportunistic access to the licensed spectrum is studied. Resource allocation is based on minimizing the symbol error rate at the receiver. Both the cases of all-participate relaying and selective relaying are considered. The objective function is derived and the constraints are detailed for both scenarios. It is then shown that the objective functions and the constraints are nonlinear and nonconvex functions of the parameters of interest, that is, source and relay powers, symbol time, and sensing time. Therefore, it is difficult to obtain closed-form solutions for the optimal resource allocation. The optimization problem is then solved using numerical techniques. Numerical results show that the all-participate system provides better performance than its selection counterpart, at the cost of greater resources. © 2012 Ammar Zafar et al.

  13. Rate Maximization in MIMO Decode-and-Forward Communications With an EH Relay and Possibly Imperfect CSI

    KAUST Repository

    Benkhelifa, Fatma

    2016-08-29

    In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) in a multiple-input multiple-output (MIMO) decode-and-forward (DF) relay system where the relay is an energy harvesting (EH) multi-antenna node equipped with an EH receiver and an information decoding (ID) receiver. The relay harvests the energy from the radio frequency (RF) signals sent by the source and uses it to forward the signals to the destination. The main objective in this paper is to maximize the achievable transmission rate of the overall link by optimizing the source/relay precoders. First, we study an upper bound on the maximum achievable rate where we assume that the EH and ID receivers operate simultaneously and have access to the whole power of the received signals. Afterwards, we study two practical schemes, which are the power splitting (PS) and time switching (TS) schemes, where the ID and EH receivers have partial access to the power or duration of the received signals. For each scheme, we have studied the complexity and the performance comparison. In addition, we considered the case of the imperfect channel estimation error and we have observed its impact on the achievable end-to-end rate and the harvested energy at the relay. © 1972-2012 IEEE.

  14. Analytical Frameworks of Cooperative and Cognitive Radio Systems with Practical Considerations

    KAUST Repository

    Khan, Fahd Ahmed

    2013-01-01

    for cooperative and cognitive radio systems considering real world scenarios and to make these technologies implementable. In most of the research on cooperative relaying, it has been assumed that the communicating nodes have perfect channel state information

  15. Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla; Chockalingam, A.

    2011-01-01

    In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a

  16. End-to-end performance of cooperative relaying in spectrum-sharing systems with quality of service requirements

    KAUST Repository

    Asghari, Vahid Reza

    2011-07-01

    We propose adopting a cooperative relaying technique in spectrum-sharing cognitive radio (CR) systems to more effectively and efficiently utilize available transmission resources, such as power, rate, and bandwidth, while adhering to the quality of service (QoS) requirements of the licensed (primary) users of the shared spectrum band. In particular, we first consider that the cognitive (secondary) user\\'s communication is assisted by an intermediate relay that implements the decode-and-forward (DF) technique onto the secondary user\\'s relayed signal to help with communication between the corresponding source and the destination nodes. In this context, we obtain first-order statistics pertaining to the first- and second-hop transmission channels, and then, we investigate the end-to-end performance of the proposed spectrum-sharing cooperative relaying system under resource constraints defined to assure that the primary QoS is unaffected. Specifically, we investigate the overall average bit error rate (BER), ergodic capacity, and outage probability of the secondary\\'s communication subject to appropriate constraints on the interference power at the primary receivers. We then consider a general scenario where a cluster of relays is available between the secondary source and destination nodes. In this case, making use of the partial relay selection method, we generalize our results for the single-relay scheme and obtain the end-to-end performance of the cooperative spectrum-sharing system with a cluster of L available relays. Finally, we examine our theoretical results through simulations and comparisons, illustrating the overall performance of the proposed spectrum-sharing cooperative system and quantify its advantages for different operating scenarios and conditions. © 2011 IEEE.

  17. Effect of RF Interference on the Security-Reliability Trade-off Analysis of Multiuser Mixed RF/FSO Relay Networks with Power Allocation

    KAUST Repository

    Abd El-Malek, Ahmed H.; Salhab, Anas; Zummo, Salam; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, the impact of radio frequency (RF) cochannel interference (CCI) on the performance of multiuser mixed RF/free-space optical (FSO) relay network with opportunistic user scheduling under eavesdropping attack is studied. The considered

  18. 77 FR 5406 - Amateur Radio Use of the Allocation at 5 MHz

    Science.gov (United States)

    2012-02-03

    ... requested by the American Radio Relay League (ARRL). The Commission also identified and sought comment on... (NTIA and FCC) and other nations in the fixed service; and (ii) Other nations in the mobile except...

  19. Alternate MIMO relaying with three AF relays using interference alignment

    KAUST Repository

    Park, Kihong; Alouini, Mohamed-Slim

    2012-01-01

    In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss

  20. 80537 based distance relay

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen

    1999-01-01

    A method for implementing a digital distance relay in the power system is described.Instructions are given on how to program this relay on a 80537 based microcomputer system.The problem is used as a practical case study in the course 53113: Micocomputer applications in the power system.The relay...

  1. Impact of Primary User Traffic on Adaptive Transmission for Cognitive Radio with Partial Relay Selection

    KAUST Repository

    Rao, Anlei; Ma, Hao; Alouini, Mohamed-Slim; Chen, Yunfei

    2012-01-01

    transmission, when the secondary user adopts adaptive transmission with a relay partially selected. From the numerical results, we can see that the primary user traffic seriously degrades average BER. The worse-link partial selection can perform almost as well

  2. Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-01-01

    In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single

  3. Protocol Design and Performance Analysis of Multiuser Mixed RF and Hybrid FSO/RF Relaying With Buffers

    KAUST Repository

    Al-Eryani, Yasser F.

    2018-03-07

    In this paper, a multiuser mixed radio frequency (RF) and hybrid free-space optical (FSO)/RF system is considered, where multiple mobile users transmit their data to an intermediate decode-and-forward relay node through RF links using a virtual multiple-input multipleoutput (MIMO) system, and the relay node forwards the multiplexed data of all users through a FSO link that is supported by a RF MIMO backup system to the destination. The relay node is equipped with a buffer in the physical layer for temporal storage of the users\\' data until the best channel conditions at the relay-destination link aremet. For this communication setup, we first propose a transmission protocol that achieves a multiplexing gain through a virtual MIMO system. After that, we derive closed-form expressions for the end-to-end outage probability, asymptotic outage probability, average symbol error rate, and the ergodic capacity when considering the delay-tolerant (finite buffer size) scenario. The results show that buffering in the physical layer provides a significant enhancement to the system performance (outage, error rate, and ergodic capacity). It is also found that pointing error and severe weather turbulence conditions become more tolerable with the existence of the relay\\'s buffer and RF backup link (in the second hop). In addition, the proposed virtual MIMO scheme shows a significant performance enhancement at a high number of receiving antennas, which introduces potential lowcomplexity diversity gain-based massive MIMO schemes.

  4. Efficient incremental relaying

    KAUST Repository

    Fareed, Muhammad Mehboob; Alouini, Mohamed-Slim

    2013-01-01

    We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission

  5. Outage performance of two-way DF relaying systems with a new relay selection metric

    KAUST Repository

    Hyadi, Amal; Benjillali, Mustapha; Alouini, Mohamed-Slim

    2012-01-01

    This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both

  6. 76 FR 24442 - Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and...

    Science.gov (United States)

    2011-05-02

    ... same meaning as the terms ``small business,'' ``small organization,'' and ``small governmental...] Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and Speech-to... Commission's Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services...

  7. Estimation of Distribution Algorithm for Resource Allocation in Green Cooperative Cognitive Radio Sensor Networks

    Directory of Open Access Journals (Sweden)

    Alagan Anpalagan

    2013-04-01

    Full Text Available Due to the rapid increase in the usage and demand of wireless sensor networks (WSN, the limited frequency spectrum available for WSN applications will be extremely crowded in the near future. More sensor devices also mean more recharging/replacement of batteries, which will cause significant impact on the global carbon footprint. In this paper, we propose a relay-assisted cognitive radio sensor network (CRSN that allocates communication resources in an environmentally friendly manner. We use shared band amplify and forward relaying for cooperative communication in the proposed CRSN. We present a multi-objective optimization architecture for resource allocation in a green cooperative cognitive radio sensor network (GC-CRSN. The proposed multi-objective framework jointly performs relay assignment and power allocation in GC-CRSN, while optimizing two conflicting objectives. The first objective is to maximize the total throughput, and the second objective is to minimize the total transmission power of CRSN. The proposed relay assignment and power allocation problem is a non-convex mixed-integer non-linear optimization problem (NC-MINLP, which is generally non-deterministic polynomial-time (NP-hard. We introduce a hybrid heuristic algorithm for this problem. The hybrid heuristic includes an estimation-of-distribution algorithm (EDA for performing power allocation and iterative greedy schemes for constraint satisfaction and relay assignment. We analyze the throughput and power consumption tradeoff in GC-CRSN. A detailed analysis of the performance of the proposed algorithm is presented with the simulation results.

  8. Security-Reliability Trade-Off Analysis for Multiuser SIMO Mixed RF/FSO Relay Networks With Opportunistic User Scheduling

    KAUST Repository

    El-Malek, Ahmed H. Abd

    2016-05-24

    In this paper, we study the performance of multiuser single-input multiple-output mixed radio frequency (RF)/free space optical (FSO) relay network with opportunistic user scheduling. The considered system includes multiple users, one amplify-and-forward relay, one destination, and a multiple-antenna eavesdropper. The users are connected with the relay node through RF links and the relay is connected with the destination through an FSO link. Both maximum ratio combining and selection combining schemes are used at the multiple-antenna relay to combine the signal received from the best user on different antennas. The RF/FSO channels models are assumed to follow Nakagami-m/gamma-gamma fading models with pointing errors. Closed-form expressions are derived for the outage probability, average symbol error probability, and ergodic channel capacity. Then, the power of the selected best user is determined to minimize the system asymptotic outage probability under the dominant RF or FSO link. Then, the considered system secrecy performance is investigated, where the closed-form expressions for the intercept probability are derived. Finally, we propose a new cooperative jamming model in which the worst user is selected by the authorized system to jam the existing eavesdropper. Monte-Carlo simulations are provided to validate the achieved exact and asymptotic results.

  9. Radio quite site qualification for the Brasilian Southern Space Observatory by monitoring the low frequency 10-240 MHz Eletromagnetic Spectrum

    Science.gov (United States)

    da Rosa, Guilherme Simon; Schuch, Nelson Jorge; Espindola Antunes, Cassio; Gomes, Natanael

    The monitoring of the level of the radio interference in the Site of the Brazilian Southern Space Observatory - SSO/CRS/CIE/INPE - MCT, (29S, 53W), São Martinho da Serra, RS, in south a of Brazil, aims to gather spectral data for the Observatory's Site qualification as a radio quite site for installation of Radio Astronomy instrumentation, free of radio noise. The determination of the radio interference level is being conducted by using a spectrum analyzer and Omni directional antennas remotely controlled through a GPIB interface, via IEEE 488 bus, and programs written in C language. That procedure allows the scanning of the Electromagnetic Spectrum power over the examined frequency range from 10 - 240MHz. The methodology for these tests was to amplify the radio signal from the antenna by a block amplifier. Subsequently, the received signals are evaluated by the spectrum analyzer. A dedicated PC computer is used for the control and data acquisition, with the developed software. The data are instantly stored in digital format and remotely transferred via VNC software from the SSO-Observatory Site to the Radio Frequency and Telecommunication Laboratory at the Southern Regional Space Research Center - CRS/CIE/INPE - MCT, in Santa Maria, RS, for analysis and storage on the radio interference data base for long period. It is compared the SSO's Electromagnetic Spectrum data obtained since the beginning of the 1990's decade, before the Site constructions, with the current observed data. Some radio transmissions were found in the observed frequency range due to some local FMs, mostly between 93.5 MHz to 105.7 MHz, which were observed in previous monitoring. A good evidence of the site quality is the fact that the power of the Electromagnetic Spectrum is much lower than that measured at the Radio Frequency and Telecommunication Laboratory, in Santa Maria, RS, where the signals do not exceed -60 dB. On the Site of the SSO, due to the low power observed, weak radio signals

  10. Alternate transmission with half-duplex relaying in MIMO interference relay networks

    KAUST Repository

    Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

    2013-01-01

    In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups

  11. Opportunistic Relay Selection With Limited Feedback

    KAUST Repository

    Eltayeb, Mohammed E.; Elkhalil, Khalil; Bahrami, Hamid Reza; Al-Naffouri, Tareq Y.

    2015-01-01

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision

  12. Power system relaying

    CERN Document Server

    Horowitz, Stanley H; Niemira, James K

    2013-01-01

    The previous three editions of Power System Relaying offer comprehensive and accessible coverage of the theory and fundamentals of relaying and have been widely adopted on university and industry courses worldwide. With the third edition, the authors have added new and detailed descriptions of power system phenomena such as stability, system-wide protection concepts and discussion of historic outages. Power System Relaying, 4th Edition continues its role as an outstanding textbook on power system protection for senior and graduate students in the field of electric power engineering and a refer

  13. Integrated Power Saving for Multiple Relays and UEs in LTE-TDD

    OpenAIRE

    Chun-Chuan Yang; Jeng-Yueng Chen; Yi-Ting Mai; Chen-Ming Yang

    2017-01-01

    In this paper, the design of integrated sleep scheduling for relay nodes and user equipments under a Donor eNB (DeNB) in the mode of Time Division Duplex (TDD) in LTE-A is presented. The idea of virtual time is proposed to deal with the discontinuous pattern of the available radio resource in TDD, and based on the estimation of the traffic load, three power saving schemes in the top-down strategy are presented. Associated mechanisms in each scheme including calculation of the virtual subframe...

  14. MIMO Four-Way Relaying

    DEFF Research Database (Denmark)

    Liu, Huaping; Sun, Fan; De Carvalho, Elisabeth

    2013-01-01

    Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} multiple-input multiple-output (MIMO) scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed...... the sum-rate of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with state-of-the-art reference schemes, based on two-way relaying with DF. The results indicate that the sum-rate of the two-phase four-way relaying scheme largely outperforms the four...

  15. Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

    KAUST Repository

    Hwang, Kyusung; Ko, Youngchai; Alouini, Mohamed-Slim

    2011-01-01

    In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

  16. Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

    KAUST Repository

    Hwang, Kyusung

    2011-02-01

    In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

  17. Opportunistic Relay Selection With Limited Feedback

    KAUST Repository

    Eltayeb, Mohammed E.

    2015-08-01

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision. This requirement poses two important challenges, which are often neglected in the literature. Firstly, the fed back channel information is usually corrupted by additive noise. Secondly, CSI feedback generates a great deal of feedback overhead (air-time) that could result in significant performance hits. In this paper, we propose a compressive sensing (CS) based relay selection algorithm that reduces the feedback overhead of relay networks under the assumption of noisy feedback channels. The proposed algorithm exploits CS to first obtain the identity of a set of relays with favorable channel conditions. Following that, the CSI of the identified relays is estimated using least squares estimation without any additional feedback. Both single and multiple relay selection cases are considered. After deriving closed-form expressions for the asymptotic end-to-end SNR at the destination and the feedback load for different relaying protocols, we show that CS-based selection drastically reduces the feedback load and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback. © 1972-2012 IEEE.

  18. Ready, steady… relay!

    CERN Multimedia

    2008-01-01

    Thursday 5 June. With another year comes another success for CERN’s Relay Race. With 76 teams taking part it was the second highest turnout in the race’s history. ‘The Shabbys’ won the relay race in 10 minutes 51 seconds.As popular as ever, this year the relay race took on the atmosphere of a mini carnival. Gathering on the lawn outside Restaurant 1, various stalls and attractions added to the party feeling of the event, with beer courtesy of ‘AGLUP’, the Belgian beer club, and a wandering jazz group entertaining spectators and competitors alike. Reflecting the greater involvement of other associations in the relay race, the president of the Staff Association Clubs Committee, James Purvis, was the guest of honour, launching the start of the race and presenting the prizes. As regular followers of the race could have probably predicted, The Shabbys were once again victorious and claimed first place. The team members th...

  19. Two-Way Multiuser Mixed RF/FSO Relaying: Performance Analysis and Power Allocation

    KAUST Repository

    Al-Eryani, Yasser F.

    2018-03-21

    In this paper, the performance of two-way multiuser mixed radio frequency/free space optical (RF/FSO) relay networks with opportunistic user scheduling and asymmetric channel fading is studied. RF links are used to conduct data transmission between users and relay node, while a FSO link is used to conduct data transmission on the last-mile communication link between the relay node and base station. The RF links are assumed to follow a Rayleigh fading model, while the FSO links are assumed to follow a unified Gamma-Gamma atmospheric turbulence fading model with pointing error. First, closed-form expressions for the exact outage probability, asymptotic (high signal-to-noise ratio) outage probability, average symbol error rate, and average ergodic channel capacity are derived assuming a heterodyne detection scheme. The asymptotic results are used to conduct a power optimization algorithm where expressions for optimal transmission power values for the transmitting nodes are provided. Additionally, performance comparisons between the considered two-way-relaying (TWR) network and the oneway- relaying (OWR) network are provided and discussed. Also, the impact of several system parameters, including number of users, pointing errors, atmospheric turbulence conditions, and outage probability threshold on the overall network performance are investigated. All the theoretical results are validated by Monte Carlo simulations. The results show that the TWR scheme almost doubles the network ergodic capacity compared to that of the OWR scheme with the same outage performance. Additionally, it is shown that under weak-to-moderate weather turbulence conditions and small pointing error, the outage probability is dominated by the RF downlink with a neglected effect for the user selection process at the RF uplink transmission. However, for severe pointing error, the outage probability is dominated by the FSO uplink/downlink transmission.

  20. Cooperative AF Relaying in Spectrum-Sharing Systems: Performance Analysis under Average Interference Power Constraints and Nakagami-m Fading

    KAUST Repository

    Xia, Minghua

    2012-06-01

    Since the electromagnetic spectrum resource becomes more and more scarce, improving spectral efficiency is extremely important for the sustainable development of wireless communication systems and services. Integrating cooperative relaying techniques into spectrum-sharing cognitive radio systems sheds new light on higher spectral efficiency. In this paper, we analyze the end-to-end performance of cooperative amplify-and-forward (AF) relaying in spectrum-sharing systems. In order to achieve the optimal end-to-end performance, the transmit powers of the secondary source and the relays are optimized with respect to average interference power constraints at primary users and Nakagami-$m$ fading parameters of interference channels (for mathematical tractability, the desired channels from secondary source to relay and from relay to secondary destination are assumed to be subject to Rayleigh fading). Also, both partial and opportunistic relay-selection strategies are exploited to further enhance system performance. Based on the exact distribution functions of the end-to-end signal-to-noise ratio (SNR) obtained herein, the outage probability, average symbol error probability, diversity order, and ergodic capacity of the system under study are analytically investigated. Our results show that system performance is dominated by the resource constraints and it improves slowly with increasing average SNR. Furthermore, larger Nakagami-m fading parameter on interference channels deteriorates system performance slightly. On the other hand, when interference power constraints are stringent, opportunistic relay selection can be exploited to improve system performance significantly. All analytical results are corroborated by simulation results and they are shown to be efficient tools for exact evaluation of system performance.

  1. Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

    KAUST Repository

    Nam, Sung Sik

    2018-01-09

    In this work, we propose an iterative relay scheduling with hybrid ARQ (IRS-HARQ) scheme which realizes fast jump-in/successive relaying and subframe-based decoding under the multiple user equipment (UE) relay environments applicable to the next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user link should be operated in an open-loop and transparent mode. The latter is due to the fact that not only there are no dedicated control channels between the UE relay and the end user but also a new cell is not created. Under this open-loop and transparent mode, our proposed protocol is implemented by partially exploiting the channel state information based on the overhearing mechanism of ACK/NACK for HARQ. Further, the iterative scheduling enables UE-to-UE direct communication with proximity that offers spatial frequency reuse and energy saving.

  2. Relay Selection with Limited and Noisy Feedback

    KAUST Repository

    Eltayeb, Mohammed E.

    2016-01-28

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI acquisition generates a great deal of feedback overhead that could result in significant transmission delays. In addition to this, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we propose a relay selection algorithm that tackles the above challenges. Instead of allocating each relay a dedicated channel for feedback, all relays share a pool of feedback channels. Following that, each relay feeds back its identity only if its effective channel (source-relay-destination) exceeds a threshold. After deriving closed-form expressions for the feedback load and the achievable rate, we show that the proposed algorithm drastically reduces the feedback overhead and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback from all relays. © 2015 IEEE.

  3. Commercial Grade Item (CGI) Dedication for Leak Detection Relays

    International Nuclear Information System (INIS)

    KOCH, M.R.; JOHNS, B.R.

    1999-01-01

    This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping and Instrumentation Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

  4. Telecommunications Relay Support of the Mars Phoenix Lander Mission

    Science.gov (United States)

    Edwards, Charles D., Jr.; Erickson, James K.; Gladden, Roy E.; Guinn, Joseph R.; Ilott, Peter A.; Jai, Benhan; Johnston, Martin D.; Kornfeld, Richard P.; Martin-Mur, Tomas J.; McSmith, Gaylon W.; hide

    2010-01-01

    The Phoenix Lander, first of NASA's Mars Scout missions, arrived at the Red Planet on May 25, 2008. From the moment the lander separated from its interplanetary cruise stage shortly before entry, the spacecraft could no longer communicate directly with Earth, and was instead entirely dependent on UHF relay communications via an international network of orbiting Mars spacecraft, including NASA's 2001 Mars Odyssey (ODY) and Mars Reconnaissance Orbiter (MRO) spacecraft, as well as ESA's Mars Express (MEX) spacecraft. All three orbiters captured critical event telemetry and/or tracking data during Phoenix Entry, Descent and Landing. During the Phoenix surface mission, ODY and MRO provided command and telemetry services, far surpassing the original data return requirements. The availability of MEX as a backup relay asset enhanced the robustness of the surface relay plan. In addition to telecommunications services, Doppler tracking observables acquired on the UHF link yielded an accurate position for the Phoenix landing site.

  5. Multi-pair cognitive two-way relaying and power allocation under imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla; Alouini, Mohamed-Slim; Aï ssa, Sonia

    2013-01-01

    In this paper, we present a robust joint relay precoder design and transceiver power allocation for a cognitive radio network under imperfect channel state information. The secondary (or cognitive) network consists of multiple pairs of single-antenna transceiver nodes and a non-regenerative two-way relay with multiple antennas which aids the intra-pair communication process of the transceiver nodes. The secondary nodes share the spectrum with a licensed primary user (PU) while guaranteeing that the interference to the PU receiver is maintained below a specified threshold. The proposed robust design is based on the minimization of the sum mean-square error (MSE) of the transceiver nodes under constraints on the secondary users' transmit powers and interference to PU the receiver. Though the original problem is non-convex, we show that the proposed design can be solved using alternating optimization of convex subproblems which have analytic or efficient numerical solutions. We illustrate the performance of the proposed designs through some selected numerical simulations. © 2013 IEEE.

  6. Multi-pair cognitive two-way relaying and power allocation under imperfect CSI

    KAUST Repository

    Pandarakkottilil, Ubaidulla

    2013-06-01

    In this paper, we present a robust joint relay precoder design and transceiver power allocation for a cognitive radio network under imperfect channel state information. The secondary (or cognitive) network consists of multiple pairs of single-antenna transceiver nodes and a non-regenerative two-way relay with multiple antennas which aids the intra-pair communication process of the transceiver nodes. The secondary nodes share the spectrum with a licensed primary user (PU) while guaranteeing that the interference to the PU receiver is maintained below a specified threshold. The proposed robust design is based on the minimization of the sum mean-square error (MSE) of the transceiver nodes under constraints on the secondary users\\' transmit powers and interference to PU the receiver. Though the original problem is non-convex, we show that the proposed design can be solved using alternating optimization of convex subproblems which have analytic or efficient numerical solutions. We illustrate the performance of the proposed designs through some selected numerical simulations. © 2013 IEEE.

  7. Buffer-Aided Relaying with Adaptive Link Selection

    DEFF Research Database (Denmark)

    Zlatanov, Nikola; Schober, Robert; Popovski, Petar

    2013-01-01

    In this paper, we consider a simple network consisting of a source, a half-duplex decode-and-forward relay, and a destination. We propose a new relaying protocol employing adaptive link selection, i.e., in any given time slot, based on the channel state information of the source-relay and the relay......-destination link a decision is made whether the source or the relay transmits. In order to avoid data loss at the relay, adaptive link selection requires the relay to be equipped with a buffer such that data can be queued until the relay-destination link is selected for transmission. We study both delay......-constrained and delay-unconstrained transmission. For the delay-unconstrained case, we characterize the optimal link selection policy, derive the corresponding throughput, and develop an optimal power allocation scheme. For the delay-constrained case, we propose to starve the buffer of the relay by choosing...

  8. Protocol Design and Performance Analysis of Multiuser Mixed RF and Hybrid FSO/RF Relaying With Buffers

    KAUST Repository

    Al-Eryani, Yasser F.; Salhab, Anas; Zummo, Salam A.; Alouini, Mohamed-Slim

    2018-01-01

    In this paper, a multiuser mixed radio frequency (RF) and hybrid free-space optical (FSO)/RF system is considered, where multiple mobile users transmit their data to an intermediate decode-and-forward relay node through RF links using a virtual multiple-input multipleoutput (MIMO) system, and the relay node forwards the multiplexed data of all users through a FSO link that is supported by a RF MIMO backup system to the destination. The relay node is equipped with a buffer in the physical layer for temporal storage of the users' data until the best channel conditions at the relay-destination link aremet. For this communication setup, we first propose a transmission protocol that achieves a multiplexing gain through a virtual MIMO system. After that, we derive closed-form expressions for the end-to-end outage probability, asymptotic outage probability, average symbol error rate, and the ergodic capacity when considering the delay-tolerant (finite buffer size) scenario. The results show that buffering in the physical layer provides a significant enhancement to the system performance (outage, error rate, and ergodic capacity). It is also found that pointing error and severe weather turbulence conditions become more tolerable with the existence of the relay's buffer and RF backup link (in the second hop). In addition, the proposed virtual MIMO scheme shows a significant performance enhancement at a high number of receiving antennas, which introduces potential lowcomplexity diversity gain-based massive MIMO schemes.

  9. Relay Selection with Limited and Noisy Feedback

    KAUST Repository

    Eltayeb, Mohammed E.; Elkhalil, Khalil; Mas'ud, Abdullahi Abubakar; Al-Naffouri, Tareq Y.

    2016-01-01

    Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI

  10. CERN Relay Race

    CERN Multimedia

    2009-01-01

    The CERN relay race, now in its 39th year, is already a well-known tradition, but this year the organizers say the event will have even more of a festival feeling. Just off the starting line of the CERN relay race.For the past few years, spectators and runners at the CERN relay race have been able to enjoy a beer while listening to music from the CERN music and jazz clubs. But this year the organizers are aiming for "even more of a festival atmosphere". As David Nisbet, President of the CERN running club and organizer of the relay race, says: "Work is not just about getting your head down and doing the theory, it’s also about enjoying the company of your colleagues." This year, on top of music from the Santa Luis Band and the Canettes Blues Band, there will be demonstrations from the Aikido and softball clubs, a stretching session by the Fitness club, as well as various stalls and of course, the well-earned beer from AGLUP, the B...

  11. Cooperative Cognitive Radio Systems over Nakagami-m Fading Channels

    KAUST Repository

    Hyadi, Amal

    2013-05-08

    This thesis aims to investigate the incorporation of cooperative techniques in cognitive radio networks over Nakagami-m fading channels. These last years, spectrum sharing mechanisms has gained a lot of interest in the wireless communication domain. Using cooperation in a cognitive set up make the use of spectrum much more efficient. Moreover, it helps to extend the coverage area of the cognitive network and also to reduce the transmitting power and, thus, the generated interference. In this work, we consider two particular scenarios for cooperative cognitive radio systems. The first scenario consider multihop regenerative relaying in an underlay cognitive set up. The cooperation is performed in the secondary system, in the presence of multiple primary users. Both interference power and peak power constraints are taking into account. Closed-form expressions for the statistical characteristics and multiple end- to-end performance metrics are derived. Different scenarios are presented to illustrate the obtained results and Monte Carlo simulations confirm the accuracy of our analytical derivations. In the second part of this work, we consider an overlay cognitive network with the spectrally efficient two-phase two-way relaying protocol. Two relay selection techniques, optimizing both the primary and the secondary communication, are presented. The overall outage performance is investigated and an optimal power allocation scheme, that ameliorate the outage performance of the system, is proposed. Numerical simulations are presented to illustrate and compare the obtained results.

  12. Physical Layer Security Using Two-Path Successive Relaying

    Directory of Open Access Journals (Sweden)

    Qian Yu Liau

    2016-06-01

    Full Text Available Relaying is one of the useful techniques to enhance wireless physical-layer security. Existing literature shows that employing full-duplex relay instead of conventional half-duplex relay improves secrecy capacity and secrecy outage probability, but this is at the price of sophisticated implementation. As an alternative, two-path successive relaying has been proposed to emulate operation of full-duplex relay by scheduling a pair of half-duplex relays to assist the source transmission alternately. However, the performance of two-path successive relaying in secrecy communication remains unexplored. This paper proposes a secrecy two-path successive relaying protocol for a scenario with one source, one destination and two half-duplex relays. The relays operate alternately in a time division mode to forward messages continuously from source to destination in the presence of an eavesdropper. Analytical results reveal that the use of two half-duplex relays in the proposed scheme contributes towards a quadratically lower probability of interception compared to full-duplex relaying. Numerical simulations show that the proposed protocol achieves the ergodic achievable secrecy rate of full-duplex relaying while delivering the lowest probability of interception and secrecy outage probability compared to the existing half duplex relaying, full duplex relaying and full duplex jamming schemes.

  13. Relay Architectures for 3GPP LTE-Advanced

    Directory of Open Access Journals (Sweden)

    Peters StevenW

    2009-01-01

    Full Text Available The Third Generation Partnership Project's Long Term Evolution-Advanced is considering relaying for cost-effective throughput enhancement and coverage extension. While analog repeaters have been used to enhance coverage in commercial cellular networks, the use of more sophisticated fixed relays is relatively new. The main challenge faced by relay deployments in cellular systems is overcoming the extra interference added by the presence of relays. Most prior work on relaying does not consider interference, however. This paper analyzes the performance of several emerging half-duplex relay strategies in interference-limited cellular systems: one-way, two-way, and shared relays. The performance of each strategy as a function of location, sectoring, and frequency reuse are compared with localized base station coordination. One-way relaying is shown to provide modest gains over single-hop cellular networks in some regimes. Shared relaying is shown to approach the gains of local base station coordination at reduced complexity, while two-way relaying further reduces complexity but only works well when the relay is close to the handset. Frequency reuse of one, where each sector uses the same spectrum, is shown to have the highest network throughput. Simulations with realistic channel models provide performance comparisons that reveal the importance of interference mitigation in multihop cellular networks.

  14. On the performance of two-way multiuser mixed RF/FSO relay networks with opportunistic scheduling & asymmetric channel gains

    KAUST Repository

    Al-Eryani, Yasser F.; Salhab, Anas M.; Zummo, Salam A.; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, the performance of two-way relaying (TWR) multiuser mixed radio frequency/free space optical (RF/FSO) relay networks with opportunistic user scheduling and asymmetric channel fading is studied. First, closed-form expressions for the exact outage probability, asymptotic (high signal-to-noise ration (SNR)) outage probability, and average ergodic channel capacity are derived assuming heterodyne detection (HD) scheme. Additionally, impacts of several system parameters including number of users, pointing errors, and atmospheric turbulence conditions on the overall network performance are investigated. All the theoretical results are validated by Monte-Carlo simulations. The results show that the TWR scheme almost doubles the network ergodic capacity compared to that of one-way relaying (OWR) scheme with the same outage performance. Additionally, the overall diversity order of the network is shown to be affected not only by the number of users, but it is also a function of the pointing error and atmospheric turbulence conditions.

  15. On the performance of two-way multiuser mixed RF/FSO relay networks with opportunistic scheduling & asymmetric channel gains

    KAUST Repository

    Al-Eryani, Yasser F.

    2017-07-20

    In this paper, the performance of two-way relaying (TWR) multiuser mixed radio frequency/free space optical (RF/FSO) relay networks with opportunistic user scheduling and asymmetric channel fading is studied. First, closed-form expressions for the exact outage probability, asymptotic (high signal-to-noise ration (SNR)) outage probability, and average ergodic channel capacity are derived assuming heterodyne detection (HD) scheme. Additionally, impacts of several system parameters including number of users, pointing errors, and atmospheric turbulence conditions on the overall network performance are investigated. All the theoretical results are validated by Monte-Carlo simulations. The results show that the TWR scheme almost doubles the network ergodic capacity compared to that of one-way relaying (OWR) scheme with the same outage performance. Additionally, the overall diversity order of the network is shown to be affected not only by the number of users, but it is also a function of the pointing error and atmospheric turbulence conditions.

  16. Monitoring of surface chemical and underground nuclear explosions with help of ionospheric radio-sounding above test site

    International Nuclear Information System (INIS)

    Krasnov, V.M.; Drobzheva, Ya.V.

    2000-01-01

    We describe the basic principles, advantages and disadvantages of ionospheric method to monitor surface chemical and underground nuclear explosions. The ionosphere is 'an apparatus' for the infra-sound measurements immediately above the test site. Using remote radio sounding of the ionosphere you can obtain that information. So you carry out the inspection at the test site. The main disadvantage of the ionospheric method is the necessity to sound the ionosphere with radio waves. (author)

  17. Full-Duplex Relay Selection in Cognitive Underlay Networks

    KAUST Repository

    Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aissa, Sonia

    2017-01-01

    In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby

  18. Capacity gains of buffer-aided moving relays

    KAUST Repository

    Zafar, Ammar

    2017-03-14

    This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

  19. Capacity gains of buffer-aided moving relays

    KAUST Repository

    Zafar, Ammar; Shaqfeh, Mohammad; Alnuweiri, Hussein; Alouini, Mohamed-Slim

    2017-01-01

    This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

  20. Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond.

    Science.gov (United States)

    Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

    2016-01-01

    In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment.

  1. Performance analysis of opportunistic nonregenerative relaying

    KAUST Repository

    Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Yang, Hongchuan

    2013-01-01

    Opportunistic relaying in cooperative communication depends on careful relay selection. However, the traditional centralized method used for opportunistic amplify-and-forward protocols requires precise measurements of channel state information at the destination. In this paper, we adopt the max-min criterion as a relay selection framework for opportunistic amplify-and-forward cooperative communications, which was exhaustively used for the decode-and-forward protocol, and offer an accurate performance analysis based on exact statistics of the local signal-to-noise ratios of the best relay. Furthermore, we evaluate the asymptotical performance and deduce the diversity order of our proposed scheme. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over Rayleigh fading channels, and we compare the max-min relay selection with their centralized channel state information-based and partial relay selection counterparts.

  2. Energy efficient circuit design using nanoelectromechanical relays

    Science.gov (United States)

    Venkatasubramanian, Ramakrishnan

    Nano-electromechanical (NEM) relays are a promising class of emerging devices that offer zero off-state leakage and behave like an ideal switch. Recent advances in planar fabrication technology have demonstrated that microelectromechanical (MEMS) scale miniature relays could be manufactured reliably and could be used to build fully functional, complex integrated circuits. The zero leakage operation of relays has renewed the interest in relay based low power logic design. This dissertation explores circuit architectures using NEM relays and NEMS-CMOS heterogeneous integration. Novel circuit topologies for sequential logic, memory, and power management circuits have been proposed taking into consideration the NEM relay device properties and optimizing for energy efficiency and area. In nanoscale electromechanical devices, dispersion forces like Van der Waals' force (vdW) affect the pull-in stability of the relay devices significantly. Verilog-A electromechanical model of the suspended gate relay operating at 1V with a nominal air gap of 5 - 10nm has been developed taking into account all the electrical, mechanical and dispersion effects. This dissertation explores different relay based latch and flip-flop topologies. It has been shown that as few as 4 relay cells could be used to build flip-flops. An integrated voltage doubler based flip flop that improves the performance by 2X by overdriving Vgb has been proposed. Three NEM relay based parallel readout memory bitcell architectures have been proposed that have faster access time, and remove the reliability issues associated with previously reported serial readout architectures. A paradigm shift in design of power switches using NEM relays is proposed. An interesting property of the relay device is that the ON state resistance (Ron) of the NEM relay switch is constant and is insensitive to the gate slew rate. This coupled with infinite OFF state resistance (Roff ) offers significant area and power advantages over CMOS

  3. 78 FR 40407 - Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and...

    Science.gov (United States)

    2013-07-05

    ...] Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and Speech-to... telecommunications relay services (TRS) program continues to offer functional equivalence to all eligible users and..., identified by CG Docket Nos. 10-51 and 03-123, by any of the following methods: Electronic Filers: Comments...

  4. Dual-Hop VLC/RF Transmission System with Energy Harvesting Relay under Delay Constraint

    KAUST Repository

    Rakia, Tamer

    2017-02-09

    In this paper, we introduce a dual-hop visible light communication (VLC) / radio frequency (RF) transmission system to extend the coverage of indoor VLC systems. The relay between the two hops is able to harvest light energy from different artificial light sources and sunlight entering the room. The relay receives data packet over a VLC channel and uses the harvested energy to retransmit it to a mobile terminal over an RF channel. We develop a novel statistical model for the harvested electrical power and analyze the probability of data packet loss. We define a system design parameter (α ∈ [0, 1)) that controls the time dedicated for excess energy harvesting and data packet retransmission. It was found that the parameter has an optimal value which minimizes the packet loss probability. Further more, this optimal value is independent of the RF channel path loss. However, optimal showed inverse dependence on the packet size.

  5. The Importance of Site Selection for Radio Astronomy

    International Nuclear Information System (INIS)

    Umar, Roslan; Abidin, Zamri Zainal; Ibrahim, Zainol Abidin

    2014-01-01

    Radio sources are very weak since this object travel very far from outer space. Radio astronomy studies are limited due to radio frequency interference (RFI) that is made by man. If the harassment is not stopped, it will provide critical problems in their radio astronomy scientists research. The purpose of this study is to provide RFI map Peninsular Malaysia with a minimum mapping techniques RFI interference. RFI mapping technique using GIS is proposed as a tool in mapping techniques. Decision-making process for the selection requires gathering information from a variety of parameters. These factors affecting the selection process are also taken account. In this study, various factors or parameters involved such as availability of telecommunications transmission (including radio and television), rainfall, water line and human activity. This study will benefit radio astronomy research especially in the RFI profile in Malaysia. Keywords: Radio Astronomy, Radio Frequency Interference (RFI), RFI mapping technique : GIS

  6. Relay test program

    International Nuclear Information System (INIS)

    Bandyopadhyay, K.K.; Kunkel, C.; Shteyngart, S.

    1994-02-01

    This report presents the results of a relay test program conducted by Brookhaven National Laboratory (BNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC). The program is a continuation of an earlier test program the results of which were published in NUREG/CR-4867. The current program was carried out in two phases: electrical testing and vibration testing. The objective was primarily to focus on the electrical discontinuity or continuity of relays and circuit breaker tripping mechanisms subjected to electrical pulses and vibration loads. The electrical testing was conducted by KEMA-Powertest Company and the vibration testing was performed at Wyle Laboratories, Huntsville, Alabama. This report discusses the test procedures, presents the test data, includes an analysis of the data and provides recommendations regarding reliable relay testing

  7. Development of the Plate Boundary Observatory GPS Low Latency Salton Trough Radio Network

    Science.gov (United States)

    Walls, C.; Miller, S.; Wilson, B.; Lawrence, S.; Arnitz, E.

    2008-05-01

    UNAVCO is developing a 20 GPS station low latency radio network that spans the San Andreas and San Jacinto faults in the region of highest strain in southern California and the narrowest part of the North America-Pacific plate boundary. The Salton Trough Radio Network (STRN) is instrumented with Ethernet bridge Intuicom EB6+ (900 MHz) radios to transmit a high rate low latency data stream from each permanent GPS site for the purpose of the following: 1) telemeter 15 second data (1 MB/day/station) to the Plate Boundary Observatory archive, 2) accommodate the timely download of 1 and 5 sample per second data following large earthquakes (4 MB/hour/station), and 3) test the UStream of 1Hz BINEX and RTCM data. Three of four phases have been completed. Office radio testing yielded transfer rates of 30-50 KB/s with subsecond latency while streaming 1 Hz data. Latency climbed to ~1.8 seconds while simultaneously streaming 1 Hz and downloading hourly 1 and 5 sample per second data files. Field testing demonstrated rates on the order of 30 KB/s. At present the radios are installed and have transfer rates of 10-40 KB/s between sites that span 10-32 km. The final phase will be the installation of the main telemetry relay where master radios will be connected to a high speed ISP near the town of Brawley. The high-rate low latency UStream data will be available to researchers who are developing prototype earthquake early warning systems in Southern California. A goal of the STRN is to make the data available rapidly enough for GPS-derived coseismic and dynamic displacements to be integrated into early warning system earthquake models. The improved earthquake models will better assist emergency response. UStream data will also aid surveyors who wish to use PBO GPS stations as permanent, high-quality base stations in real-time kinematic surveys.

  8. Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

    KAUST Repository

    Zafar, Ammar

    2013-12-01

    This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal-to-noise-ratio (SNR) above a certain peak value and satisfying the peak power constraints at the source and relay nodes. To achieve this objective, an optimal relay selection and power allocation strategy is derived by solving the power minimization problem. Numerical results show that the derived optimal strategy enhances the energy-efficiency as compared to a benchmark scheme in which both the source and the selected relay transmit at peak power. © 2013 IEEE.

  9. SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

    KAUST Repository

    Benkhelifa, Fatma

    2017-02-09

    In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate maximization problem is intractable, we tackle a simplified problem where we maximize the sum of the harvested energy at the relays, we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relay- destination channels. The interference mitigation at the destinations is managed in two ways: either to fix the interference covariance matrices at the destination and update them at each iteration until convergence, or to cancel the interference using an algorithm similar to the BD method. We provide numerical results to show the relevance of our proposed solution.

  10. Spoiled Onions: Exposing Malicious Tor Exit Relays

    OpenAIRE

    Winter, Philipp; Lindskog, Stefan

    2014-01-01

    Several hundred Tor exit relays together push more than 1 GiB/s of network traffic. However, it is easy for exit relays to snoop and tamper with anonymised network traffic and as all relays are run by independent volunteers, not all of them are innocuous. In this paper, we seek to expose malicious exit relays and document their actions. First, we monitored the Tor network after developing a fast and modular exit relay scanner. We implemented several scanning modules for detecting common attac...

  11. Outage Analysis of Mixed Underlay Cognitive RF MIMO and FSO Relaying with Interference Reduction

    KAUST Repository

    Al-Qahtani, Fawaz S.; El-Malek, Ahmed H. Abd; Ansari, Imran S.; Radaydeh, Redha Mahmoud Mesleh; Zummo, Salam A.

    2017-01-01

    In this paper, we study the outage performance of multiuser mixed underlay radio frequency (RF)/multidestinations free-space optical (FSO) links. For RF links, we consider a secondary network with multiple users that can communicate with multiple destinations through a relaying node. The relay is equipped with an antenna array at the RF side, and it uses the amplify-and-forward (AF) protocol. The primary users (PUs) are equipped with multiple antennas at transmit and receive nodes. The RF link is subjected to the aggregate PUs interference effect on the secondary network. To reduce the effect of PUs interference on secondary network at the relay node, two interference cancellation (IC) schemes are adopted, which vary in terms of complexity and achieved performance. On the other hand, the multidestination FSO links can be exploited to further enhance the quality of the second hop, and their associated channel models account for pointing errors, intensity modulation/direct detection, and heterodyne detection. For the aforementioned system model, we obtain exact and asymptotic closed-form expressions for the end-to-end outage probability. To further enhance system performance, optimal power allocation between the two hops is obtained based on the derived asymptotic outage probability expressions.

  12. Outage Analysis of Mixed Underlay Cognitive RF MIMO and FSO Relaying with Interference Reduction

    KAUST Repository

    Al-Qahtani, Fawaz S.

    2017-03-22

    In this paper, we study the outage performance of multiuser mixed underlay radio frequency (RF)/multidestinations free-space optical (FSO) links. For RF links, we consider a secondary network with multiple users that can communicate with multiple destinations through a relaying node. The relay is equipped with an antenna array at the RF side, and it uses the amplify-and-forward (AF) protocol. The primary users (PUs) are equipped with multiple antennas at transmit and receive nodes. The RF link is subjected to the aggregate PUs interference effect on the secondary network. To reduce the effect of PUs interference on secondary network at the relay node, two interference cancellation (IC) schemes are adopted, which vary in terms of complexity and achieved performance. On the other hand, the multidestination FSO links can be exploited to further enhance the quality of the second hop, and their associated channel models account for pointing errors, intensity modulation/direct detection, and heterodyne detection. For the aforementioned system model, we obtain exact and asymptotic closed-form expressions for the end-to-end outage probability. To further enhance system performance, optimal power allocation between the two hops is obtained based on the derived asymptotic outage probability expressions.

  13. SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

    KAUST Repository

    Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate

  14. Control circuit for transformer relay

    International Nuclear Information System (INIS)

    Wyatt, G.A.

    1984-01-01

    A control circuit for a transformer relay which will automatically momentarily control the transformer relay to a selected state upon energization of the control circuit. The control circuit has an energy storage element and a current director coupled in series and adapted to be coupled with the secondary winding of the transformer relay. A device for discharge is coupled across the energy storage element. The energy storage element and current director will momentarily allow a unidirectional flow of current in the secondary winding of the transformer relay upon application of energy to the control circuit. When energy is not applied to the control circuit the device for discharge will allow the energy storage element to discharge and be available for another operation of the control circuit

  15. Multi-diversity combining and selection for relay-assisted mixed RF/FSO system

    Science.gov (United States)

    Chen, Li; Wang, Weidong

    2017-12-01

    We propose and analyze multi-diversity combining and selection to enhance the performance of relay-assisted mixed radio frequency/free-space optics (RF/FSO) system. We focus on a practical scenario for cellular network where a single-antenna source is communicating to a multi-apertures destination through a relay equipped with multiple receive antennas and multiple transmit apertures. The RF single input multiple output (SIMO) links employ either maximal-ratio combining (MRC) or receive antenna selection (RAS), and the FSO multiple input multiple output (MIMO) links adopt either repetition coding (RC) or transmit laser selection (TLS). The performance is evaluated via an outage probability analysis over Rayleigh fading RF links and Gamma-Gamma atmospheric turbulence FSO links with pointing errors where channel state information (CSI) assisted amplify-and-forward (AF) scheme is considered. Asymptotic closed-form expressions at high signal-to-noise ratio (SNR) are also derived. Coding gain and diversity order for different combining and selection schemes are further discussed. Numerical results are provided to verify and illustrate the analytical results.

  16. Improper Signaling for Virtual Full-Duplex Relay Systems

    KAUST Repository

    Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

    2017-01-01

    Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

  17. Improper Signaling for Virtual Full-Duplex Relay Systems

    KAUST Repository

    Gaafar, Mohamed

    2017-02-14

    Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

  18. Speech-to-Speech Relay Service

    Science.gov (United States)

    Consumer Guide Speech to Speech Relay Service Speech-to-Speech (STS) is one form of Telecommunications Relay Service (TRS). TRS is a service that allows persons with hearing and speech disabilities ...

  19. Outage performance of two-way DF relaying systems with a new relay selection metric

    KAUST Repository

    Hyadi, Amal

    2012-04-01

    This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both users. To evaluate the performance of the proposed system, the outage probability is derived in a general case (where an arbitrary channel is considered), and then over independently but not necessarily identically distributed (i.n.i.d.) Rayleigh fading channels. The analytical results are verified through simulations. © 2012 IEEE.

  20. Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

    KAUST Repository

    Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

    2016-01-01

    In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

  1. Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

    KAUST Repository

    Nam, Sung Sik

    2016-11-29

    In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

  2. Improper signaling in two-path relay channels

    KAUST Repository

    Gaafar, Mohamed

    2017-07-03

    Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

  3. Improper signaling in two-path relay channels

    KAUST Repository

    Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

    2017-01-01

    Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

  4. Relay self interference minimisation using tapped filter

    KAUST Repository

    Jazzar, Saleh

    2013-05-01

    In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage and reduce the required transmitted signal power. One problem that faces relays communications is the leaked signal from the relay\\'s output to its input. This will cause an SI problem where the new received signal at the relay\\'s input will be added with the unwanted leaked signal from the relay\\'s output. A Solution is proposed in this paper to estimate and minimise this SI which is based upon using a tapped filter at the destination. To get the optimum weights for this tapped filter, some channel parameters must be estimated first. This is performed blindly at the destination without the need of any training. This channel parameter estimation method is named the blind-self-interference-channel-estimation (BSICE) method. The next step in the proposed solution is to estimate the tapped filter\\'s weights. This is performed by minimising the mean squared error (MSE) at the destination. This proposed method is named the MSE-Optimum Weight (MSE-OW) method. Simulation results are provided in this paper to verify the performance of BSICE and MSE-OW methods. © 2013 IEEE.

  5. Performance limitations of relay neurons.

    Directory of Open Access Journals (Sweden)

    Rahul Agarwal

    Full Text Available Relay cells are prevalent throughout sensory systems and receive two types of inputs: driving and modulating. The driving input contains receptive field properties that must be transmitted while the modulating input alters the specifics of transmission. For example, the visual thalamus contains relay neurons that receive driving inputs from the retina that encode a visual image, and modulating inputs from reticular activating system and layer 6 of visual cortex that control what aspects of the image will be relayed back to visual cortex for perception. What gets relayed depends on several factors such as attentional demands and a subject's goals. In this paper, we analyze a biophysical based model of a relay cell and use systems theoretic tools to construct analytic bounds on how well the cell transmits a driving input as a function of the neuron's electrophysiological properties, the modulating input, and the driving signal parameters. We assume that the modulating input belongs to a class of sinusoidal signals and that the driving input is an irregular train of pulses with inter-pulse intervals obeying an exponential distribution. Our analysis applies to any [Formula: see text] order model as long as the neuron does not spike without a driving input pulse and exhibits a refractory period. Our bounds on relay reliability contain performance obtained through simulation of a second and third order model, and suggest, for instance, that if the frequency of the modulating input increases or the DC offset decreases, then relay increases. Our analysis also shows, for the first time, how the biophysical properties of the neuron (e.g. ion channel dynamics define the oscillatory patterns needed in the modulating input for appropriately timed relay of sensory information. In our discussion, we describe how our bounds predict experimentally observed neural activity in the basal ganglia in (i health, (ii in Parkinson's disease (PD, and (iii in PD during

  6. Modular relay control

    OpenAIRE

    Ivarsson, Mikael

    2010-01-01

    Enics Sweden AB, Västerås, is an electronics manufacturing services company with its main business in manufacturing electronics. Most, if not all, electronic devices that are manufactured are being widely tested before delivery to ensure proper functionality. Often during tests a large number of signals are measured by one to a few digital multimeters and are therefore controlled through relays. Relays are also used when applying stimuli with high currents or voltages to the unit under test. ...

  7. Analytical Frameworks of Cooperative and Cognitive Radio Systems with Practical Considerations

    KAUST Repository

    Khan, Fahd Ahmed

    2013-08-01

    Cooperative and cognitive radio systems have been proposed as a solution to improve the quality-of-service (QoS) and spectrum efficiency of existing communication systems. The objective of this dissertation is to propose and analyze schemes for cooperative and cognitive radio systems considering real world scenarios and to make these technologies implementable. In most of the research on cooperative relaying, it has been assumed that the communicating nodes have perfect channel state information (CSI). However, in reality, this is not the case and the nodes may only have an estimate of the CSI or partial knowledge of the CSI. Thus, in this dissertation, depending on the amount of CSI available, novel receivers are proposed to improve the performance of amplify-and forward relaying. Specifically, new coherent receivers are derived which do not perform channel estimation at the destination by using the received pilot signals directly for decoding. The derived receivers are based on new metrics that use distribution of the channels and the noise to achieve improved symbol-error-rate (SER) performance. The SER performance of the derived receivers is further improved by utilizing the decision history in the receivers. In cases where receivers with low complexity are desired, novel non-coherent receiver which detects the signal without knowledge of CSI is proposed. In addition, new receivers are proposed for the situation when only partial CSI is available at the destination i.e. channel knowledge of either the source-relay link or the relay-destination link but not both, is available. These receivers are termed as `half-coherent receivers\\' since they have channel-state-information of only one of the two links in the system. In practical systems, the CSI at the communicating terminals becomes outdated due to the time varying nature of the channel and results in system performance degradation. In this dissertation, the impact of using outdated CSI for relay selection on

  8. On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

    KAUST Repository

    Park, Kihong; Alouini, Mohamed-Slim; Park, Seongho; Ko, Youngchai

    2012-01-01

    In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity

  9. Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

    KAUST Repository

    Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

    2018-01-01

    -generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user

  10. Multiple relay selection for delay-limited applications

    KAUST Repository

    Alsharoa, Ahmad M.

    2013-12-01

    A multiple relay selection system model that implements the decode-and-forward mode is investigated. All communication nodes are assumed to be equipped by multiple antennas. Furthermore, lattices space-time coded multiple-input multiple-output half duplex channel is applied. The main goal is to increase the throughput of the system by selecting multiple number of relays. The selection criteria depends on the maximum decoding delay at relays where the system implements a decoding time-out algorithm at each relay. This leads to a significant saving in the overall system power consumptions and attempts to solve the relays synchronization problem. All results are presented using numerical simulations. © 2012 IEEE.

  11. Airborne relay-based regional positioning system.

    Science.gov (United States)

    Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

    2015-05-28

    Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

  12. Capacity Bounds on the Downlink of Symmetric, Multi-Relay, Single-Receiver C-RAN Networks

    Directory of Open Access Journals (Sweden)

    Shirin Saeedi Bidokhti

    2017-11-01

    Full Text Available The downlink of symmetric Cloud Radio Access Networks (C-RANs with multiple relays and a single receiver is studied. Lower and upper bounds are derived on the capacity. The lower bound is achieved by Marton’s coding, which facilitates dependence among the multiple-access channel inputs. The upper bound uses Ozarow’s technique to augment the system with an auxiliary random variable. The bounds are studied over scalar Gaussian C-RANs and are shown to meet and characterize the capacity for interesting regimes of operation.

  13. Physical Layer Security Enhancement in Multiuser Mixed RF#x002F;FSO Relay Networks under RF Interference

    KAUST Repository

    El-Malek, Ahmed H. Abd; Salhab, Anas M.; Zummo, Salam A.; Alouini, Mohamed-Slim

    2017-01-01

    In this paper, the impact of radio frequency (RF) co-channel interference (CCI) on the performance of multiuser (MU) mixed RF#x002F;free space optical (FSO) relay network with opportunistic user scheduling is studied. In the considered system, a user is opportunistically selected to communicate with a single destination through an amplify-and- forward (AF) relay in the presence of a single passive eavesdropper. The RF#x002F;FSO channel models are assumed to follow Rayleigh#x002F;Gamma-Gamma fading models, respectively with pointing errors and identical RF CCI signals. Exact closed-form expression for the system outage probability is derived. Then, an asymptotic expression for the outage probability is obtained at the high signal- to-interference-plus-noise ratio (SINR) regime. The asymptotic results are used to formulate a power allocation problem to obtain optimal RF transmission power. Then, the secrecy performance is studied in the presence of CCI at both the authorized relay and eavesdropper by obtaining exact and asymptotic closed-form expressions for the intercept probability. The derived analytical formulas herein are supported by numerical and simulation results to clarify the main contributions of the work.

  14. Physical Layer Security Enhancement in Multiuser Mixed RF#x002F;FSO Relay Networks under RF Interference

    KAUST Repository

    El-Malek, Ahmed H. Abd

    2017-05-12

    In this paper, the impact of radio frequency (RF) co-channel interference (CCI) on the performance of multiuser (MU) mixed RF#x002F;free space optical (FSO) relay network with opportunistic user scheduling is studied. In the considered system, a user is opportunistically selected to communicate with a single destination through an amplify-and- forward (AF) relay in the presence of a single passive eavesdropper. The RF#x002F;FSO channel models are assumed to follow Rayleigh#x002F;Gamma-Gamma fading models, respectively with pointing errors and identical RF CCI signals. Exact closed-form expression for the system outage probability is derived. Then, an asymptotic expression for the outage probability is obtained at the high signal- to-interference-plus-noise ratio (SINR) regime. The asymptotic results are used to formulate a power allocation problem to obtain optimal RF transmission power. Then, the secrecy performance is studied in the presence of CCI at both the authorized relay and eavesdropper by obtaining exact and asymptotic closed-form expressions for the intercept probability. The derived analytical formulas herein are supported by numerical and simulation results to clarify the main contributions of the work.

  15. Bilayer expurgated LDPC codes with uncoded relaying

    Directory of Open Access Journals (Sweden)

    Md. Noor-A-Rahim

    2017-08-01

    Full Text Available Bilayer low-density parity-check (LDPC codes are an effective coding technique for decode-and-forward relaying, where the relay forwards extra parity bits to help the destination to decode the source bits correctly. In the existing bilayer coding scheme, these parity bits are protected by an error correcting code and assumed reliably available at the receiver. We propose an uncoded relaying scheme, where the extra parity bits are forwarded to the destination without any protection. Through density evolution analysis and simulation results, we show that our proposed scheme achieves better performance in terms of bit erasure probability than the existing relaying scheme. In addition, our proposed scheme results in lower complexity at the relay.

  16. A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

    KAUST Repository

    Rao, Anlei

    2015-09-11

    Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (QoS) requirements. For the later type design, previous works has worked on minimizing the approximated power consumption. In this paper, exact power consumption for all relays is derived into a quadratic form by diagonalizing the minimum-square error (MSE) matrix, and the relay precoding matrix is designed by optimizing this quadratic form with the help of semidefinite programming (SDP) relaxation. Our simulation results show that such a design can achieve a gain of around 3 dB against the previous design, which optimized the approximated power consumption. © 2015 IEEE.

  17. Opportunistic Relay Selection with Cooperative Macro Diversity

    Directory of Open Access Journals (Sweden)

    Yu Chia-Hao

    2010-01-01

    Full Text Available We apply a fully opportunistic relay selection scheme to study cooperative diversity in a semianalytical manner. In our framework, idle Mobile Stations (MSs are capable of being used as Relay Stations (RSs and no relaying is required if the direct path is strong. Our relay selection scheme is fully selection based: either the direct path or one of the relaying paths is selected. Macro diversity, which is often ignored in analytical works, is taken into account together with micro diversity by using a complete channel model that includes both shadow fading and fast fading effects. The stochastic geometry of the network is taken into account by having a random number of randomly located MSs. The outage probability analysis of the selection differs from the case where only fast fading is considered. Under our framework, distribution of the received power is formulated using different Channel State Information (CSI assumptions to simulate both optimistic and practical environments. The results show that the relay selection gain can be significant given a suitable amount of candidate RSs. Also, while relay selection according to incomplete CSI is diversity suboptimal compared to relay selection based on full CSI, the loss in average throughput is not too significant. This is a consequence of the dominance of geometry over fast fading.

  18. Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

    KAUST Repository

    Khan, Fahd Ahmed; Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

    2015-01-01

    In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

  19. Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

    KAUST Repository

    Khan, Fahd Ahmed

    2015-05-01

    In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

  20. Programmable Ultra-Lightweight System Adaptable Radio Satellite Base Station

    Science.gov (United States)

    Varnavas, Kosta; Sims, Herb

    2015-01-01

    With the explosion of the CubeSat, small sat, and nanosat markets, the need for a robust, highly capable, yet affordable satellite base station, capable of telemetry capture and relay, is significant. The Programmable Ultra-Lightweight System Adaptable Radio (PULSAR) is NASA Marshall Space Flight Center's (MSFC's) software-defined digital radio, developed with previous Technology Investment Programs and Technology Transfer Office resources. The current PULSAR will have achieved a Technology Readiness Level-6 by the end of FY 2014. The extensibility of the PULSAR will allow it to be adapted to perform the tasks of a mobile base station capable of commanding, receiving, and processing satellite, rover, or planetary probe data streams with an appropriate antenna.

  1. MaROS Strategic Relay Planning and Coordination Interfaces

    Science.gov (United States)

    Allard, Daniel A.

    2010-01-01

    The Mars Relay Operations Service (MaROS) is designed to provide planning and analysis tools in support of ongoing Mars Network relay operations. Strategic relay planning requires coordination between lander and orbiter mission ground data system (GDS) teams to schedule and execute relay communications passes. MaROS centralizes this process, correlating all data relevant to relay coordination to provide a cohesive picture of the relay state. Service users interact with the system through thin-layer command line and web user interface client applications. Users provide and utilize data such as lander view periods of orbiters, Deep Space Network (DSN) antenna tracks, and reports of relay pass performance. Users upload and download relevant relay data via formally defined and documented file structures including some described in Extensible Markup Language (XML). Clients interface with the system via an http-based Representational State Transfer (ReST) pattern using Javascript Object Notation (JSON) formats. This paper will provide a general overview of the service architecture and detail the software interfaces and considerations for interface design.

  2. Relay selection from an effective capacity perspective

    KAUST Repository

    Yang, Yuli

    2013-09-01

    In this work, we consider a cooperative network where multiple relay nodes having different modulation capabilities assist the end-to-end communication between a source and its destination. Firstly, we evaluate the effective capacity (EC) performance of the network under study. According to the analysis, an EC-based relay selection criterion is proposed. Based on the proposed selection rule and half-duplex decode-and-forward protocol, the activated relays cooperatively help with the packet transmission from the source. At the destination, packet combining is taken into account to improve the quality of service. Compared to the popular scheme, opportunistic relay selection, numerical results are provided to prove the validity and advantages of our proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between with and without packet combining at the destination. © 2013 IEEE.

  3. Reversal thyristor-relay direct current commutator

    International Nuclear Information System (INIS)

    Ivanenko, A.I.

    1982-01-01

    A thyristor-relay commutator used for alteration of the leading magnetic field direction in experiments with polarized neutrons is described. The commutator flowsheet is presented. Thyristors, connected so as to allow the relay trigger operation mode, are used as controllable electronic relay. Two connected in series coils with the total inductance of the order of 0.28 H serve as the electronic relay load. The arc-free current commutation is effected at the moment of the minimal current across the load terminals, which allows to easily reverse the current up to 10 A at a volatage, v <= 150 V. The experience gained within a year of operation has shown that the commutator meets the requirements of reliability and tuning

  4. Analysis of errors of radiation relay, (1)

    International Nuclear Information System (INIS)

    Koyanagi, Takami; Nakajima, Sinichi

    1976-01-01

    The statistical error of liquid level controlled by radiation relay is analysed and a method of minimizing the error is proposed. This method comes to the problem of optimum setting of the time constant of radiation relay. The equations for obtaining the value of time constant are presented and the numerical results are shown in a table and plotted in a figure. The optimum time constant of the upper level control relay is entirely different from that of the lower level control relay. (auth.)

  5. 49 CFR 236.52 - Relayed cut-section.

    Science.gov (United States)

    2010-10-01

    ..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

  6. Quantum cryptography with an ideal local relay

    DEFF Research Database (Denmark)

    Spedalieri, Gaetana; Ottaviani, Carlo; Braunstein, Samuel L.

    2015-01-01

    We consider two remote parties connected to a relay by two quantum channels. To generate a secret key, they transmit coherent states to the relay, where the states are subject to a continuous-variable (CV) Bell detection. We study the ideal case where Alice's channel is lossless, i.e., the relay ...

  7. A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

    KAUST Repository

    Rao, Anlei; Park, Kihong; Alouini, Mohamed-Slim

    2015-01-01

    Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (Qo

  8. The importance of Radio Quiet Zone (RQZ) for radio astronomy

    Science.gov (United States)

    Umar, Roslan; Abidin, Zamri Zainal; Ibrahim, Zainol Abidin

    2013-05-01

    Most of radio observatories are located in isolated areas. Since radio sources from the universe is very weak, astronomer need to avoid radio frequency interference (RFI) from active spectrum users and radio noise produced by human made (telecommunication, mobile phone, microwave user and many more. There are many observatories around the world are surrounded by a Radio Quiet Zone (RQZ), which is it was set up using public or state laws. A Radio Quiet Zone normally consists of two areas: an exclusive area in which totally radio emissions are forbidden, with restrictions for residents and business developments, and a larger (radius up to 100 km above) coordination area where the power of radio transmission limits to threshold levels. Geographical Information System (GIS) can be used as a powerful tool in mapping large areas with varying RQZ profiles. In this paper, we report the initial testing of the usage of this system in order to identify the areas were suitable for Radio Quiet Zone. Among the important parameters used to develop the database for our GIS are population density, information on TV and telecommunication (mobile phones) transmitters, road networks (highway), and contour shielding. We will also use other information gathered from on-site RFI level measurements on selected 'best' areas generated by the GIS. The intention is to find the best site for the purpose of establishing first radio quiet zones for radio telescope in Malaysia.

  9. Amplify-and-forward relaying in wireless communications

    CERN Document Server

    Rodriguez, Leonardo Jimenez; Le-Ngoc, Tho

    2015-01-01

    This SpringerBrief explores the advantage of relaying techniques in addressing the increasing demand for high data rates and reliable services over the air. It demonstrates how to design cost-effective relay systems that provide high spectral efficiency and fully exploit the diversity of the relay channel. The brief covers advances in achievable rates, power allocation schemes, and error performance for half-duplex (HD) and full-duplex (FD) amplify-and-forward (AF) single-relay systems. The authors discuss the capacity and respective optimal power allocation for a wide range of HD protocols ov

  10. Full-Duplex Relay Selection in Cognitive Underlay Networks

    KAUST Repository

    Khafagy, Mohammad Galal

    2017-09-30

    In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint, which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic FDRS with residual self-interference (RSI) by deriving the exact cumulative distribution function of its end-to-end signal-to-interference-plus-noise ratio under Nakagami-m fading. We also evaluate the offered diversity gain of relay selection for different full-duplex cooperation schemes in the presence/absence of a direct source-destination link. When the adopted RSI link gain model is sublinear in the relay power, which agrees with recent research findings, we show that remarkable diversity gain can be recovered even in the presence of an interfering direct link. Second, we evaluate the end-to-end performance of FDRS with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

  11. Relay exchanges in elite short track speed skating.

    Science.gov (United States)

    Hext, Andrew; Heller, Ben; Kelley, John; Goodwill, Simon

    2017-06-01

    In short track speed skating, the relay exchange provides an additional strategic component to races by allowing a team to change the skater involved in the pack race. Typically executed every 1½ laps, it is the belief of skaters and coaches that during this period of the race, time can be gained or lost due to the execution of the relay exchange. As such, the aim of this study was to examine the influence of the relay exchange on a team's progression through a 5000 m relay race. Using data collected from three World Cup relay events during the 2012-2013 season, the time taken to complete the straight for the scenarios with and without the relay exchange were compared at different skating speeds for the corner exit prior to the straight. Overall, the influence of the relay exchange was found to be dependent on this corner exit speed. At slower corner exit speeds (12.01-13.5 m/s), relay exchange straight times were significantly faster than the free skating scenario (P < 0.01). While at faster corner exit speeds (14.01-15 m/s), straight times were significantly slower (P < 0.001). The findings of this study suggest that the current norm of executing relay exchanges every 1½ laps may not be optimal. Instead, varying the frequency of relay exchange execution throughout the race could allow: (1) time to be gained relative to other teams; and (2) facilitate other race strategies by providing an improved opportunity to overtake.

  12. On Alternate Relaying with Improper Gaussian Signaling

    KAUST Repository

    Gaafar, Mohamed; Amin, Osama; Ikhlef, Aissa; Chaaban, Anas; Alouini, Mohamed-Slim

    2016-01-01

    In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

  13. On Alternate Relaying with Improper Gaussian Signaling

    KAUST Repository

    Gaafar, Mohamed

    2016-06-06

    In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

  14. An assessment of fire vulnerability for aged electrical relays

    International Nuclear Information System (INIS)

    Vigil, R.A.; Nowlen, S.P.

    1995-03-01

    There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized

  15. Microprocessor protection relays: new prospects or new problems?

    OpenAIRE

    Gurevich, Vladimir

    2006-01-01

    The internal architecture and principles of operation of microprocessor-based devices including so-called "microprocessor protective relays" have little in common with devices called "electric relays". But microprocessor-based relay protection devices are gradually driving out the traditional electromechanical and even electronic relay protection of virtually from all fields of power and electrical engineering. Advantages of microprocessor-based protection means over traditional ones are far ...

  16. The CERN Relay Race: A Runaway Success!

    CERN Multimedia

    Staff Association

    2018-01-01

    24th May saw the traditional Relay Race take place at CERN, organised jointly by the Running Club and the CERN Staff Association. In 2018, the Relay Race lived up to expectations with a record number of participants, with no fewer than 848 entries across different categories! In total 135 teams of 6 runners and 38 walkers completed the course on the Meyrin site in beautiful sunshine. Congratulations to all those who took part! Ghislain Roy, President of the Staff Association, fired the starting pistol for the first batch of runners, which included a team from the Directorate, with the Director General also taking part. Demonstrating interest in this event at the highest level of the Organization. Thank you for this much-appreciated commitment! Also a number of very high-level runners brought added excitement to the 2018 edition. The 1000-meter men’s race was won by Marcin Patecki from the CERN Running Club in 2’40, just in front of Baptiste Fieux from the Berthie Sport team who came in at...

  17. Error-rate performance analysis of opportunistic regenerative relaying

    KAUST Repository

    Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

    2011-01-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can

  18. Near-optimal power allocation with PSO algorithm for MIMO cognitive networks using multiple AF two-way relays

    KAUST Repository

    Alsharoa, Ahmad M.

    2014-06-01

    In this paper, the problem of power allocation for a multiple-input multiple-output two-way system is investigated in underlay Cognitive Radio (CR) set-up. In the CR underlay mode, secondary users are allowed to exploit the spectrum allocated to primary users in an opportunistic manner by respecting a tolerated temperature limit. The secondary networks employ an amplify-and-forward two-way relaying technique in order to maximize the sum rate under power budget and interference constraints. In this context, we formulate an optimization problem that is solved in two steps. First, we derive a closed-form expression of the optimal power allocated to terminals. Then, we employ a strong optimization tool based on particle swarm optimization algorithm to find the power allocated to secondary relays. Simulation results demonstrate the efficiency of the proposed solution and analyze the impact of some system parameters on the achieved performance. © 2014 IEEE.

  19. Experimental evaluation of earthquake induced relay chattering

    International Nuclear Information System (INIS)

    Bandyopadhyay, K.; Hofmayer, C.; Shteyngart, S.

    1990-01-01

    An experimental evaluation of relay performance under vibratory environments is discussed in this paper. Single frequency excitation was used for most tests. Limited tests were performed with random multifrequency inputs. The capacity of each relay was established based on a two-millisecond chatter criterion. The experimental techniques are described and the effects of parameters in controlling the relay capacity levels are illustrated with test data. A wide variation of the capacity levels was observed due to the influence of parameters related to the design of the relay and nature of the input motion. 3 refs., 15 figs

  20. Local dialogue and information within the frame of the setting up of relay antennas. Decreasing the exposure to electromagnetic waves emitted by mobile phone relay antennas. First phase report by Francois Brottes, chairman of the 'experimentations' COMOP

    International Nuclear Information System (INIS)

    Brottes, Francois

    2011-01-01

    The first part of this report describes the progress made on local dialogue and information within the frame of the setting up of relay antennas. It describes the implemented method with a selection of nine local communities, the main results of the dialogue (establishment of an information file, development of a tool set for the pilot communities, and operation, steering and assessment of experimentations). The second part describes the progress made on the exposure of population to electromagnetic waves emitted by mobile phone relay antennas (context, method, exposure status, simulation of the decreasing of relay antenna power, site experimentations). The third part proposes a set of recommendations related to local dialogue and information and to exposure

  1. Relay protection features of frequency-adjustable electric drive

    Science.gov (United States)

    Kuprienko, V. V.

    2018-03-01

    The features of relay protection of high-voltage electric motors in composition of the frequency-adjustable electric drive are considered in the article. The influence of frequency converters on the stability of the operation of various types of relay protection used on electric motors is noted. Variants of circuits for connecting relay protection devices are suggested. The need to develop special relay protection devices for a frequency-adjustable electric drive is substantiated.

  2. Hanford quarterly seismic report - 97B seismicity on and near the Hanford Site, Pasco Basin, Washington, January 1, 1997--March 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Hartshorn, D.C.; Reidel, S.P.

    1997-05-01

    Hanford Seismic Monitoring provides an uninterrupted collection of high-quality raw and processed seismic data from the Hanford Seismic Network (HSN) for the U.S. Department of Energy and contractors. The staff also locates and identifies sources of seismic activity and monitors changes in the historical pattern of seismic activity at the Hanford Site. The data are compiled, archived, and published for use by the Hanford Site for activities ranging from waste management, Natural Phenomena Hazards assessments, and engineering design and construction. In addition, the seismic monitoring organizations works with the Hanford Site Emergency Services Organization to provide assistance in the event of an earthquake on the Hanford Site. The HSN and the Eastern Washington Regional Network (EWRN) consist of 41 individual sensor sites and 15 radio relay sites maintained by the Seismic Monitoring staff. Most stations and five relay sites are solar powered. The operational rate for the second quarter of FY97 for stations in the HSN was 97.23% and for stations of the EWRN was 99.93%. For fiscal year (FY) 1997 second quarter (97B), the acquisition computer triggered two hundred and forth-eight times. Of these triggers three were local earthquakes: one in the pre-basalt sediments, and two in the crystalline basement. The geologic and tectonic environments are discussed in the report.

  3. Hanford quarterly seismic report - 97B seismicity on and near the Hanford Site, Pasco Basin, Washington, January 1, 1997 - March 31, 1997

    International Nuclear Information System (INIS)

    Hartshorn, D.C.; Reidel, S.P.

    1997-05-01

    Hanford Seismic Monitoring provides an uninterrupted collection of high-quality raw and processed seismic data from the Hanford Seismic Network (HSN) for the U.S. Department of Energy and contractors. The staff also locates and identifies sources of seismic activity and monitors changes in the historical pattern of seismic activity at the Hanford Site. The data are compiled, archived, and published for use by the Hanford Site for activities ranging from waste management, Natural Phenomena Hazards assessments, and engineering design and construction. In addition, the seismic monitoring organizations works with the Hanford Site Emergency Services Organization to provide assistance in the event of an earthquake on the Hanford Site. The HSN and the Eastern Washington Regional Network (EWRN) consist of 41 individual sensor sites and 15 radio relay sites maintained by the Seismic Monitoring staff. Most stations and five relay sites are solar powered. The operational rate for the second quarter of FY97 for stations in the HSN was 97.23% and for stations of the EWRN was 99.93%. For fiscal year (FY) 1997 second quarter (97B), the acquisition computer triggered two hundred and forth-eight times. Of these triggers three were local earthquakes: one in the pre-basalt sediments, and two in the crystalline basement. The geologic and tectonic environments are discussed in the report

  4. Relay Telecommunications for the Coming Decade of Mars Exploration

    Science.gov (United States)

    Edwards, C.; DePaula, R.

    2010-01-01

    Over the past decade, an evolving network of relay-equipped orbiters has advanced our capabilities for Mars exploration. NASA's Mars Global Surveyor, 2001 Mars Odyssey, and Mars Reconnaissance Orbiter (MRO), as well as ESA's Mars Express Orbiter, have provided telecommunications relay services to the 2003 Mars Exploration Rovers, Spirit and Opportunity, and to the 2007 Phoenix Lander. Based on these successes, a roadmap for continued Mars relay services is in place for the coming decade. MRO and Odyssey will provide key relay support to the 2011 Mars Science Laboratory (MSL) mission, including capture of critical event telemetry during entry, descent, and landing, as well as support for command and telemetry during surface operations, utilizing new capabilities of the Electra relay payload on MRO and the Electra-Lite payload on MSL to allow significant increase in data return relative to earlier missions. Over the remainder of the decade a number of additional orbiter and lander missions are planned, representing new orbital relay service providers and new landed relay users. In this paper we will outline this Mars relay roadmap, quantifying relay performance over time, illustrating planned support scenarios, and identifying key challenges and technology infusion opportunities.

  5. Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

    KAUST Repository

    Benkhelifa, Fatma

    2016-09-20

    In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

  6. Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

    KAUST Repository

    Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

    2016-01-01

    In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

  7. Evaluation of Harmonics Impact on Digital Relays

    Directory of Open Access Journals (Sweden)

    Kinan Wannous

    2018-04-01

    Full Text Available This paper presents the concept of the impact of harmonic distortion on a digital protection relay. The aim is to verify and determine the reasons of a mal-trip or failure to trip the protection relays; the suggested solution of the harmonic distortion is explained by a mathematical model in the Matlab Simulink programming environment. The digital relays have been tested under harmonic distortions in order to verify the function of the relays algorithm under abnormal conditions. The comparison between the protection relay algorithm under abnormal conditions and a mathematical model in the Matlab Simulink programming environment based on injected harmonics of high values is provided. The test is separated into different levels; the first level is based on the harmonic effect of an individual harmonic and mixed harmonics. The test includes the effect of the harmonics in the location of the fault point into distance protection zones. This paper is a new proposal in the signal processing of power quality disturbances using Matlab Simulink and the power quality impact on the measurements of the power system quantities; the test simulates the function of protection in power systems in terms of calculating the current and voltage values of short circuits and their faults. The paper includes several tests: frequency variations and decomposition of voltage waveforms with Fourier transforms (model and commercial relay, the effect of the power factor on the location of fault points, the relation between the tripping time and the total harmonic distortion (THD levels in a commercial relay, and a comparison of the THD capture between the commercial relay and the model.

  8. Relay testing parametric investigation of seismic fragility

    International Nuclear Information System (INIS)

    Bandyopadhyay, K.; Hofmayer, C.; Kassir, M.; Pepper, S.

    1989-01-01

    The seismic capacity of most electrical equipment is governed by malfunction of relays. An evaluation of the existing relay test data base at Brookhaven National Laboratory (BNL) has indicated that the seismic fragility of a relay may depend on various parameters related to the design or the input motion. In particular, the electrical mode, contact state, adjustment, chatter duration acceptance limit, and the frequency and the direction of the vibration input have been considered to influence the relay fragility level. For a particular relay type, the dynamics of its moving parts depends on the exact model number and vintage and hence, these parameters may also influence the fragility level. In order to investigate the effect of most of these parameters on the seismic fragility level, BNL has conducted a relay test program. The testing has been performed at Wyle Laboratories. Establishing the correlation between the single frequency fragility test input and the corresponding multifrequency response spectrum (TRS) is also an objective of this test program. This paper discusses the methodology used for testing and presents a brief summary of important test results. 1 ref., 10 figs

  9. Capacity Bounds and Mapping Design for Binary Symmetric Relay Channels

    Directory of Open Access Journals (Sweden)

    Majid Nasiri Khormuji

    2012-12-01

    Full Text Available Capacity bounds for a three-node binary symmetric relay channel with orthogonal components at the destination are studied. The cut-set upper bound and the rates achievable using decode-and-forward (DF, partial DF and compress-and-forward (CF relaying are first evaluated. Then relaying strategies with finite memory-length are considered. An efficient algorithm for optimizing the relay functions is presented. The Boolean Fourier transform is then employed to unveil the structure of the optimized mappings. Interestingly, the optimized relay functions exhibit a simple structure. Numerical results illustrate that the rates achieved using the optimized low-dimensional functions are either comparable to those achieved by CF or superior to those achieved by DF relaying. In particular, the optimized low-dimensional relaying scheme can improve on DF relaying when the quality of the source-relay link is worse than or comparable to that of other links.

  10. An economically viable space power relay system

    Science.gov (United States)

    Bekey, Ivan; Boudreault, Richard

    1999-09-01

    This paper describes and analyzes the economics of a power relay system that takes advantage of recent technological advances to implement a system that is economically viable. A series of power relay systems are described and analyzed which transport power ranging from 1,250 megawatts to 5,000 megawatts, and distribute it to receiving sites at transcontinental distances. Two classes of systems are discussed—those with a single reflector and delivering all the power to a single rectenna, and a second type which has multiple reflectors and distributes it to 10 rectenna sites, sharing power among them. It is shown that when offering electricity at prices competitive to those prevalent in developed cities in the US that a low IRR is inevitable, and economic feasibility of a business is unlikely. However, when the target market is Japan where the prevalent electricity prices are much greater, that an IRR exceeding 65% is readily attainable. This is extremely attractive to potential investors, making capitalization of a venture likely. The paper shows that the capital investment required for the system can be less than 1 per installed watt, contributing less than 0.02 /KW-hr to the cost of energy provision. Since selling prices in feasible regions range from 0.18 to over 030 $/kW-hr, these costs are but a small fraction of the operating expenses. Thus a very large IRR is possible for such a business.

  11. Duplex Schemes in Multiple Antenna Two-Hop Relaying

    Directory of Open Access Journals (Sweden)

    Anja Klein

    2008-04-01

    Full Text Available A novel scheme for two-hop relaying defined as space division duplex (SDD relaying is proposed. In SDD relaying, multiple antenna beamforming techniques are applied at the intermediate relay station (RS in order to separate downlink and uplink signals of a bi-directional two-hop communication between two nodes, namely, S1 and S2. For conventional amplify-and-forward two-hop relaying, there appears a loss in spectral efficiency due to the fact that the RS cannot receive and transmit simultaneously on the same channel resource. In SDD relaying, this loss in spectral efficiency is circumvented by giving up the strict separation of downlink and uplink signals by either time division duplex or frequency division duplex. Two novel concepts for the derivation of the linear beamforming filters at the RS are proposed; they can be designed either by a three-step or a one-step concept. In SDD relaying, receive signals at S1 are interfered by transmit signals of S1, and receive signals at S2 are interfered by transmit signals of S2. An efficient method in order to combat this kind of interference is proposed in this paper. Furthermore, it is shown how the overall spectral efficiency of SDD relaying can be improved if the channels from S1 and S2 to the RS have different qualities.

  12. A blind matching algorithm for cognitive radio networks

    KAUST Repository

    Hamza, Doha R.

    2016-08-15

    We consider a cognitive radio network where secondary users (SUs) are allowed access time to the spectrum belonging to the primary users (PUs) provided that they relay primary messages. PUs and SUs negotiate over allocations of the secondary power that will be used to relay PU data. We formulate the problem as a generalized assignment market to find an epsilon pairwise stable matching. We propose a distributed blind matching algorithm (BLMA) to produce the pairwise-stable matching plus the associated power allocations. We stipulate a limited information exchange in the network so that agents only calculate their own utilities but no information is available about the utilities of any other users in the network. We establish convergence to epsilon pairwise stable matchings in finite time. Finally we show that our algorithm exhibits a limited degradation in PU utility when compared with the Pareto optimal results attained using perfect information assumptions. © 2016 IEEE.

  13. Two-Hop Secure Communication Using an Untrusted Relay

    Directory of Open Access Journals (Sweden)

    Xiang He

    2009-01-01

    Full Text Available We consider a source-destination pair that can only communicate through an untrusted intermediate relay node. The intermediate node is willing to employ a designated relaying scheme to facilitate reliable communication between the source and the destination. Yet, the information it relays needs to be kept secret from it. In this two-hop communication scenario, where the use of the untrusted relay node is essential, we find that a positive secrecy rate is achievable. The center piece of the achievability scheme is the help provided by either the destination node with transmission capability, or an external “good samaritan” node. In either case, the helper performs cooperative jamming that confuses the eavesdropping relay and disables it from being able to decipher what it is relaying. We next derive an upper bound on the secrecy rate for this system. We observe that the gap between the upper bound and the achievable rate vanishes as the power of the relay node goes to infinity. Overall, the paper presents a case for intentional interference, that is, cooperative jamming, as an enabler for secure communication.

  14. Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

    KAUST Repository

    Zafar, Ammar; Radaydeh, Redha Mahmoud Mesleh; Chen, Yunfei; Alouini, Mohamed-Slim

    2013-01-01

    This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal

  15. Application of a proposed overcurrent relay in radial distribution networks

    Energy Technology Data Exchange (ETDEWEB)

    Conde, A.; Vazquez, E. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, A.P. 36-F, CU, CP 66450, San Nicolas de los Garza, Nuevo Leon (Mexico)

    2011-02-15

    This paper contains the application criteria and coordination process for a proposed overcurrent relay in a radial power system with feed from one or multiple sources. This relay uses independent functions to detect faults and to calculate the operation time. Also this relay uses a time element function that allows it to reduce the time relay operation, enhancing the backup protection. Some of the proposed approaches improve the sensitivity of the relay. The selection of the best approach in the proposed relay is defined by the needs of the application. The proposed protection can be considered as an additional function protection to conventional overcurrent relays. (author)

  16. Time of arrival based location estimation for cooperative relay networks

    KAUST Repository

    Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Hussain, Syed Imtiaz; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

    2010-01-01

    In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

  17. Time of arrival based location estimation for cooperative relay networks

    KAUST Repository

    Çelebi, Hasari Burak

    2010-09-01

    In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

  18. Full-Duplex opportunistic relay selection in future spectrum-sharing networks

    KAUST Repository

    Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aï ssa, Sonia

    2015-01-01

    We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

  19. Full-Duplex opportunistic relay selection in future spectrum-sharing networks

    KAUST Repository

    Khafagy, Mohammad Galal

    2015-06-01

    We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

  20. Discrete radioisotopic relays of a cyclic action

    International Nuclear Information System (INIS)

    Klempner, K.S.; Vasil'ev, A.G.

    1975-01-01

    A functional diagram of discrete radioisotopic relay equipment (RRP) with cyclic action was examined. An analysis of its rapid action and reliability under stationary conditions and transition regimes is presented. A structural diagram of radioisotopic relay equipment shows three radiation detectors, a pulse standardizer, an integrator and a power amplifier with a threshold cut-off device. It was established that the basic properties of the RRP - rapid action and reliability - are determined entirely by the counting rate of the average frequency of pulses from the radiation detector, n 0 and n 1 , in the 0 and 1 states (absence of current in the electromagnetic relay winding and activation of the winding of the output relay), capacities N 1 and N 2 of the dual counters, and the frequency of the transition threshold, f, of the generator. Formulas are presented which allow making engineering calculations for determining the optimum RRP parameters. High speed and reliability are shown, which are determined by the production purposes of the relay

  1. Asymmetric Modulation Gains in Network Coded Relay Networks

    DEFF Research Database (Denmark)

    Roetter, Daniel Enrique Lucani; Fitzek, Frank

    2015-01-01

    Wireless relays have usually been considered in two ways. On the one hand, a physical layer approach focused on per-packet reliability and involving the relay on each packet transmission. On the other, recent approaches have relied on the judicious activation of the relay at the network level to ...

  2. Beamforming Design for Coordinated Direct and Relay Systems

    DEFF Research Database (Denmark)

    Sun, Fan; De Carvalho, Elisabeth; Thai, Chan

    2012-01-01

    Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference. In this paper we investigate the novel transmission modes, based on amplify-and-forward, that arise when the relay...... an iterative solution, as well as derive an upper performance bound. The numerical results demonstrate a clear benefit from usage of multiple antennas at the relay node....

  3. On-Site Inspection RadioIsotopic Spectroscopy (Osiris) System Development

    Energy Technology Data Exchange (ETDEWEB)

    Caffrey, Gus J. [Idaho National Laboratory, Idaho Falls, ID (United States); Egger, Ann E. [Idaho National Laboratory, Idaho Falls, ID (United States); Krebs, Kenneth M. [Idaho National Laboratory, Idaho Falls, ID (United States); Milbrath, B. D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jordan, D. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Warren, G. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilmer, N. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-09-01

    We have designed and tested hardware and software for the acquisition and analysis of high-resolution gamma-ray spectra during on-site inspections under the Comprehensive Nuclear-Test-Ban Treaty (CTBT). The On-Site Inspection RadioIsotopic Spectroscopy—Osiris—software filters the spectral data to display only radioisotopic information relevant to CTBT on-site inspections, e.g.,132I. A set of over 100 fission-product spectra was employed for Osiris testing. These spectra were measured, where possible, or generated by modeling. The synthetic test spectral compositions include non-nuclear-explosion scenarios, e.g., a severe nuclear reactor accident, and nuclear-explosion scenarios such as a vented underground nuclear test. Comparing its computer-based analyses to expert visual analyses of the test spectra, Osiris correctly identifies CTBT-relevant fission product isotopes at the 95% level or better.The Osiris gamma-ray spectrometer is a mechanically-cooled, battery-powered ORTEC Transpec-100, chosen to avoid the need for liquid nitrogen during on-site inspections. The spectrometer was used successfully during the recent 2014 CTBT Integrated Field Exercise in Jordan. The spectrometer is controlled and the spectral data analyzed by a Panasonic Toughbook notebook computer. To date, software development has been the main focus of the Osiris project. In FY2016-17, we plan to modify the Osiris hardware, integrate the Osiris software and hardware, and conduct rigorous field tests to ensure that the Osiris system will function correctly during CTBT on-site inspections. The planned development will raise Osiris to technology readiness level TRL-8; transfer the Osiris technology to a commercial manufacturer, and demonstrate Osiris to potential CTBT on-site inspectors.

  4. On-Site Inspection RadioIsotopic Spectroscopy (Osiris) System Development

    International Nuclear Information System (INIS)

    Caffrey, Gus J.; Egger, Ann E.; Krebs, Kenneth M.; Milbrath, B. D.; Jordan, D. V.; Warren, G. A.; Wilmer, N. G.

    2015-01-01

    We have designed and tested hardware and software for the acquisition and analysis of high-resolution gamma-ray spectra during on-site inspections under the Comprehensive Nuclear-Test-Ban Treaty (CTBT). The On-Site Inspection RadioIsotopic Spectroscopy-Osiris-software filters the spectral data to display only radioisotopic information relevant to CTBT on-site inspections, e.g.,132I. A set of over 100 fission-product spectra was employed for Osiris testing. These spectra were measured, where possible, or generated by modeling. The synthetic test spectral compositions include non-nuclear-explosion scenarios, e.g., a severe nuclear reactor accident, and nuclear-explosion scenarios such as a vented underground nuclear test. Comparing its computer-based analyses to expert visual analyses of the test spectra, Osiris correctly identifies CTBT-relevant fission product isotopes at the 95% level or better.The Osiris gamma-ray spectrometer is a mechanically-cooled, battery-powered ORTEC Transpec-100, chosen to avoid the need for liquid nitrogen during on-site inspections. The spectrometer was used successfully during the recent 2014 CTBT Integrated Field Exercise in Jordan. The spectrometer is controlled and the spectral data analyzed by a Panasonic Toughbook notebook computer. To date, software development has been the main focus of the Osiris project. In FY2016-17, we plan to modify the Osiris hardware, integrate the Osiris software and hardware, and conduct rigorous field tests to ensure that the Osiris system will function correctly during CTBT on-site inspections. The planned development will raise Osiris to technology readiness level TRL-8; transfer the Osiris technology to a commercial manufacturer, and demonstrate Osiris to potential CTBT on-site inspectors.

  5. 36 CFR 292.21 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... transmission line systems, substations, commercial radio transmitters, relays or repeater stations, antennas, and other electronic sites and associated structures. Traditional uses are ranching, grazing, farming...

  6. Hanford quarterly seismic report - 97C seismicity on and near the Hanford Site, Pasco Basin, Washington. Quarterly report, April 1, 1997--June 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Hartshorn, D.C.; Reidel, S.P.; Rohay, A.C.

    1997-08-01

    Hanford Seismic Monitoring provides an uninterrupted collection of high-quality raw and processed seismic data from the Hanford Seismic Network (HSN) for the U.S. Department of Energy and contractors. The staff also locates and identifies sources of seismic activity and monitors changes in the historical pattern of seismic activity at the Hanford Site. The data are compiled, archived, and published for use by the Hanford Site for activities ranging from waste management, Natural Phenomena Hazards assessments, and engineering design and construction. In addition, the seismic monitoring organization works with the Hanford Site Emergency Services Organization to provide assistance in the event of an earthquake on the Hanford Site. The HSN and the Eastern Washington Regional Network (EWRN) consist of 41 individual sensor sites and 15 radio relay sites maintained by the Seismic Monitoring staff. Most stations and five relay sites are solar powered. The operational rate for the second quarter of FY97 for stations in the HSN was 100% and for stations of the EWRN was 99.99%. For fiscal year (FY) 1997 third quarter (97C), the acquisition computer triggered 183. Of these triggers twenty one were local earthquakes: sixteen in the Columbus River Basalt Group, one in the pre-basalt sediments, and four in the crystalline basement. The geologic and tectonic environments are discussed in the report.

  7. Distance relay performance in future converter dominated power systems

    DEFF Research Database (Denmark)

    Sarkar, Moumita; Jia, Jundi; Yang, Guangya

    2017-01-01

    Increasing penetration of converter-based generations in power system has led to new system challenges. Short circuit power response from converter-based generations is different from that of traditional synchronous generators. Power electronic converters can be designed for over-current only up ...... of converter controls on fault current response of converter-based generations is also investigated. Index Terms—Converter control, distance relays, power system protection, system modelling....... to 1.1-1.25 times of its nominal value. Low availability of short circuit power can cause many challenges such as misoperation of distance relays. The aim of this paper is to investigate the effect of converter dominated systems on performance of distance relays. Backup functionality of the distance...... relay is major concern as miscoordination of backup relays in case of cascading faults can lead to severe stress in system, which can develop into blackout. In this paper, response of relays in traditional system is compared with response of relays in low short-circuit-current power systems. Impact...

  8. Distributed stability control using intelligent voltage-margin relay

    Energy Technology Data Exchange (ETDEWEB)

    Wiszniewski, A.; Rebizant, W. [Wroclaw Univ. of Technology (Poland); Klimek, A. [Powertech Labs Inc., Surrey, BC (Canada)

    2010-07-01

    This paper presented an intelligent relay that operates if the load to source impedance ratio decreases to a level that is dangerously close to the stability limit, which leads to power system blackouts. The intelligent voltage-margin/difference relay installed at receiving substations automatically initiates action if the voltage stability margin drops to a dangerously low level. The relay decides if the tap changing devices are to be blocked and if under-voltage load shedding should be initiated, thereby mitigating an evolving instability. The intelligent relay has two levels of operation. At the first stage, which corresponds to the higher load to source impedance ratio, the relay initiates blocking of the tap changer. At the second stage, corresponding to the lower source to load impedance ratio, load shedding is initiated. The relay operates when the load to source impedance ratio reaches a certain predetermined level, but it does not depend either on the level of the source voltage or on the difference of source and load impedance phase angles. The algorithm for the relay is relatively simple and uses only locally available signals. Consequently, the transformer is well controlled to eliminate the cases of voltage instability. 6 refs., 7 figs.

  9. Asymptotic analysis for Nakagami-m fading channels with relay selection

    KAUST Repository

    Zhong, Caijun

    2011-06-01

    In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels. We derive their respective outage probability expressions in the asymptotic high signal-to-noise ratio (SNR) regime, from which the diversity order and coding gain are analyzed. In addition, we investigate the impact of power allocation between the source and relay terminals and derive the diversity-multiplexing tradeoff (DMT) for these relay selection systems. The theoretical findings suggest that partial relay selection can improve the diversity of the system and can achieve the same DMT as the "best" relay selection scheme under certain conditions. © 2011 IEEE.

  10. LTE-Advanced Relay Technology and Standardization

    CERN Document Server

    Yuan, Yifei

    2013-01-01

    LTE-Advanced Relay Technology and Standardization provides a timely reference work for relay technology with the finalizing of LTE Release 10 specifications. LTE-Advanced is quickly becoming the global standard for 4G cellular communications. The relay technology, as one of the key features in LTE-Advanced, helps not only to improve the system coverage and capacity, but also to save the costs of laying wireline backhaul. As a leading researcher in the field of LTE-Advanced standards, the author provides an in-depth description of LTE-A relay technology, and explains in detail the standard specification and design principles.     Readers from both academic and industrial fields can find sections of interest to them: Sections 2 & 4 could benefit researchers in academia and those who are engaged in exploratory work, while Sections 3 & 4 are more useful to engineers. Dr. Yifei Yuan is the Technical Director at the Standards Department of ZTE Inc.

  11. ATLAS participation to the 36th Annual CERN Relay Race

    CERN Multimedia

    Gagnon, P.

    On May 17, the Annual CERN relay race took place for the 36th time. This is a fun relay race where a team of six runners runs around the CERN site in Meyrin, up and down many hills, to cover the following distances: the first runner runs 1000 m, the second and third runners cover 800 m each, the fourth and fifth runners each have 500 m and finally, the sixth runner covers the last 300 m all the way to the finish line. Each year, serious and occasionnal runners who take this opportunity to make it their only running moment of the year, give it their best to run the 3.9 km loop in times ranging from a mere 10:39.9 for the best team this year to 18:14.3 for the last of the 65 teams that completed the race. Nobody was wasting time at the starting line of the CERN Annual Relay Race. ATLAS was better represented than ever with a record of eight ATLAS teams participating in this race organized by the CERN running club. The names of the ATLAS participants, as well as the team official times are given in the t...

  12. New results on performance analysis of opportunistic regenerative relaying

    KAUST Repository

    Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

    2013-01-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

  13. Accurate performance analysis of opportunistic decode-and-forward relaying

    KAUST Repository

    Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

    2011-01-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

  14. RADIO DIAGNOSTICS OF ELECTRON ACCELERATION SITES DURING THE ERUPTION OF A FLUX ROPE IN THE SOLAR CORONA

    Energy Technology Data Exchange (ETDEWEB)

    Carley, Eoin P.; Gallagher, Peter T. [Astrophysics Research Group, School of Physics, Trinity College Dublin, Dublin 2 (Ireland); Vilmer, Nicole, E-mail: eoin.carley@obspm.fr [LESIA, Observatoire de Paris, PSL Research University, CNRS, Sorbonne Universités, UPMC Univ. Paris 06, Univ. Paris Diderot, Sorbonne Paris Cité, 5 place Jules Janssen, F-92195 Meudon (France)

    2016-12-10

    Electron acceleration in the solar corona is often associated with flares and the eruption of twisted magnetic structures known as flux ropes. However, the locations and mechanisms of such particle acceleration during the flare and eruption are still subject to much investigation. Observing the exact sites of particle acceleration can help confirm how the flare and eruption are initiated and how they evolve. Here we use the Atmospheric Imaging Assembly to analyze a flare and erupting flux rope on 2014 April 18, while observations from the Nançay Radio Astronomy Facility allow us to diagnose the sites of electron acceleration during the eruption. Our analysis shows evidence of a pre-formed flux rope that slowly rises and becomes destabilized at the time of a C-class flare, plasma jet, and the escape of ≳75 keV electrons from the rope center into the corona. As the eruption proceeds, continued acceleration of electrons with energies of ∼5 keV occurs above the flux rope for a period over 5 minutes. At the flare peak, one site of electron acceleration is located close to the flare site, while another is driven by the erupting flux rope into the corona at speeds of up to 400 km s{sup −1}. Energetic electrons then fill the erupting volume, eventually allowing the flux rope legs to be clearly imaged from radio sources at 150–445 MHz. Following the analysis of Joshi et al. (2015), we conclude that the sites of energetic electrons are consistent with flux rope eruption via a tether cutting or flux cancellation scenario inside a magnetic fan-spine structure. In total, our radio observations allow us to better understand the evolution of a flux rope eruption and its associated electron acceleration sites, from eruption initiation to propagation into the corona.

  15. Opportunistic transmitter selection for selfless overlay cognitive radios

    KAUST Repository

    Shaqfeh, Mohammad

    2013-11-01

    We propose an opportunistic strategy to grant channel access to the primary and secondary transmitters in causal selfless overlay cognitive radios over block-fading channels. The secondary transmitter helps the primary transmitter by relaying the primary messages opportunistically, aided by a buffer to store the primary messages temporarily. The optimal channel-aware transmitter- selection strategy is the solution of the maximization of the average secondary rate under the average primary rate requirement and the buffer stability constraints. Numerical results demonstrate the gains of the proposed opportunistic selection strategy. © 2013 IEEE.

  16. Electric equipment technical regulation on a relay

    International Nuclear Information System (INIS)

    1995-01-01

    It is about a relay for power protection. It describes the definitions of structure, a point of contact protection of contact, reclosing, relay scheme and input circuit. It explains normal use condition, special use condition, rated frequency, rated voltage and rated current, fluctuation range of permission of incoming relay. It deals with general structing outer case, correction device, operation indicator and outer terminal condition sort and method of the test. It adds the marks and pictures about currents

  17. Location-based Relay Selection and Power Adaptation Enabling Simultaneous Transmissions

    DEFF Research Database (Denmark)

    Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

    2010-01-01

    Relaying is a well known technique to extend coverage and improve conditions for nodes in the outer coverage region. In this paper we propose a relaying scheme that exploits the spatial separation of relay and destination pairs to improve throughput by allowing simultaneous transmissions....... The proposed scheme is a cross-layer optimization for two-hop relaying that uses position information to jointly optimize relay selection and relay transmit power, maximizing Medium Access Control layer throughput. Further, in order to calculate the expected throughput, we apply a probabilistic model...... that takes into account MAC retransmissions and timing behavior of the IEEE 802.11 Distributed Coordination Function mode. Our results show an increase in throughput of approximately 20% is achievable for the proposed scheme when compared to two-hop relaying in the analyzed scenario....

  18. Performance of hybrid-ARQ with incremental redundancy over relay channels

    KAUST Repository

    Chelli, Ali

    2012-12-01

    In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears the transmitted messages over the different HARQ rounds and tries to decode the data packet. In case of successful decoding at the relay, both the relay and the source cooperate to transmit the message to the destination. A maximum number M of HARQ rounds is considered. The channel realizations are independent for different HARQ rounds. We assume Rayleigh fading channels for the links source-relay, source-destination, and relay-destination. We investigate the performance of HARQ-IR over relay channel from an information theoretic perspective. Analytical expressions are derived for the information outage probability, the average number of transmissions, and the average transmission rate. We illustrate through our investigation the benefit of relaying. We also show the impact of the target outage probability and the maximum number M of HARQ rounds on the outage probability, the average number of transmissions, and the average transmission rate. © 2012 IEEE.

  19. Measurement Technique in Radio Frequency Interference (RFI) Study for Radio Astronomy Purposes

    International Nuclear Information System (INIS)

    Roslan Umar; Roslan Umar; Nor Hazmin Sabri; Zainol Abidin Ibrahim; Zamri Zainal Abidin; Asyaari Muhamad

    2015-01-01

    In this paper, we will review our method in making measurements of radio frequency interference (RFI) in order to investigate the sereneness of interference in selected radio interference in Malaysia and Thailand. The selected site are University of Malaya (UM), Universiti Pendidikan Sultan Idris (UPSI), Ubon (UB) and Chiang Mai (CM). The major RFI affecting radio astronomical windows below 1 GHz are electronic equipment system specifically radio navigation between 73.1 MHz and 75.2 MHz, radio broadcasting (151 MHz, 151.8 MHz and 152 MHz), aeronautical navigation (245.5 MHz, 248.7 MHz and 249 MHz and also fixed mobile at 605 MHz, 608.3 MHz, 612.2 MHz, 613.3 MHz. It is obviously showed that all sites within this region are free from interference between 320MHz and 330 MHz and is the best specific region to be considered for solar burst monitoring. We also investigate the effect of RFI on discovery of solar burst. (author)

  20. On Buffer-Aided Multiple-Access Relay Channel

    DEFF Research Database (Denmark)

    Liu, Rongkuan; Popovski, Petar; Wang, Gang

    2016-01-01

    This letter treats uplink scenario where M user equipments (UEs) send to a base station (BS), possibly via a common relay station (RS) that is equipped with a buffer. This is a multiple-access relay channel aided by a buffer. We devise a protocol in which the transmission mode is selected...... entirely at the BS, while simultaneously a number of UEs sends new messages to the BS. The results show that the adaptive selection of direct and buffer-aided relay transmissions leads to significant average throughput gains....

  1. Cooperative AF Relaying in Spectrum-Sharing Systems: Outage Probability Analysis under Co-Channel Interferences and Relay Selection

    KAUST Repository

    Xia, Minghua

    2012-11-01

    For cooperative amplify-and-forward (AF) relaying in spectrum-sharing wireless systems, secondary users share spectrum resources originally licensed to primary users to communicate with each other and, thus, the transmit power of secondary transmitters is strictly limited by the tolerable interference powers at primary receivers. Furthermore, the received signals at a relay and at a secondary receiver are inevitably interfered by the signals from primary transmitters. These co-channel interferences (CCIs) from concurrent primary transmission can significantly degrade the performance of secondary transmission. This paper studies the effect of CCIs on outage probability of the secondary link in a spectrum-sharing environment. In particular, in order to compensate the performance loss due to CCIs, the transmit powers of a secondary transmitter and its relaying node are respectively optimized with respect to both the tolerable interference powers at the primary receivers and the CCIs from the primary transmitters. Moreover, when multiple relays are available, the technique of opportunistic relay selection is exploited to further improve system performance with low implementation complexity. By analyzing lower and upper bounds on the outage probability of the secondary system, this study reveals that it is the tolerable interference powers at primary receivers that dominate the system performance, rather than the CCIs from primary transmitters. System designers will benefit from this result in planning and designing next-generation broadband spectrum-sharing systems.

  2. Relay self interference minimisation using tapped filter

    KAUST Repository

    Jazzar, Saleh; Al-Naffouri, Tareq Y.

    2013-01-01

    In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage

  3. Relay selection from an effective capacity perspective

    KAUST Repository

    Yang, Yuli; Ma, Hao; Aï ssa, Sonia

    2013-01-01

    proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between

  4. Decrease of the exposure to electromagnetic waves emitted by mobile phone relay antennas. Synthesis report on experimentations performed by the COPIC

    International Nuclear Information System (INIS)

    2013-01-01

    A synthetic introduction outlines that simulations reveal a globally low level of public exposure to waves emitted by relay antennas, discusses lessons learned from exposure measurements, indicates that possibilities of treatment exist for the most exposed places, outlines the consequences of a global decrease of exposure on service coverage and quality, outlines a necessary increase of the number of antennas to conceal low exposure and coverage, and that the deployment of 4G should result in an increase of public exposure. Then, the main part of the report presents the fundamental notions related to mobile phone networks and radio waves (electromagnetic radiation, radiofrequency waves and mobile phones, relay antennas and networks, legal thresholds), the implemented method the characteristics of studied areas. It reports the methodology, exposure simulations and exposure measurements, coverage simulations and service quality measurements. It discusses the treatment of the most exposed locations (results from simulations and from measurements). It discusses the results of simulations and experimentations of a decrease of the power of relay antennas, of the simulation of the impact of theoretical 4G additional antennas on exposure. Results obtained in different towns and locations are reported in appendix

  5. 76 FR 72124 - Internet-Based Telecommunications Relay Service Numbering

    Science.gov (United States)

    2011-11-22

    ... Docket No. 10-191; FCC 11-123] Internet-Based Telecommunications Relay Service Numbering AGENCY: Federal..., the information collection associated with the Commission's Internet- Based Telecommunications Relay... Telecommunications Relay Service Numbering, CG Docket No. 03-123; WC Docket No. 05-196; WC Docket No. 10-191; FCC 11...

  6. Using a micromachined magnetostatic relay in commutating a DC motor

    Science.gov (United States)

    Tai, Yu-Chong (Inventor); Wright, John A. (Inventor); Lilienthal, Gerald (Inventor)

    2004-01-01

    A DC motor is commutated by rotating a magnetic rotor to induce a magnetic field in at least one magnetostatic relay in the motor. Each relay is activated in response to the magnetic field to deliver power to at least one corresponding winding connected to the relay. In some cases, each relay delivers power first through a corresponding primary winding and then through a corresponding secondary winding to a common node. Specific examples include a four-pole, three-phase motor in which each relay is activated four times during one rotation of the magnetic rotor.

  7. Optimized Policies for Improving Fairness of Location-based Relay Selection

    DEFF Research Database (Denmark)

    Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

    2013-01-01

    For WLAN systems in which relaying is used to improve throughput performance for nodes located at the cell edge, node mobility and information collection delays can have a significant impact on the performance of a relay selection scheme. In this paper we extend our existing Markov Chain modeling...... framework for relay selection to allow for efficient calculation of relay policies given either mean throughput or kth throughput percentile as optimization criterium. In a scenario with static access point, static relay, and a mobile destination node, the kth throughput percentile optimization...

  8. Generalized instantly decodable network coding for relay-assisted networks

    KAUST Repository

    Elmahdy, Adel M.

    2013-09-01

    In this paper, we investigate the problem of minimizing the frame completion delay for Instantly Decodable Network Coding (IDNC) in relay-assisted wireless multicast networks. We first propose a packet recovery algorithm in the single relay topology which employs generalized IDNC instead of strict IDNC previously proposed in the literature for the same relay-assisted topology. This use of generalized IDNC is supported by showing that it is a super-set of the strict IDNC scheme, and thus can generate coding combinations that are at least as efficient as strict IDNC in reducing the average completion delay. We then extend our study to the multiple relay topology and propose a joint generalized IDNC and relay selection algorithm. This proposed algorithm benefits from the reception diversity of the multiple relays to further reduce the average completion delay in the network. Simulation results show that our proposed solutions achieve much better performance compared to previous solutions in the literature. © 2013 IEEE.

  9. Relay race

    CERN Multimedia

    Staff Association

    2012-01-01

    The CERN Relay Race will take place around the Meyrin site on Thursday 24th May at 12:00. This annual event is for teams of six runners covering distances of 1000 m, 800 m, 800 m, 500 m, 500 m and 300 m respectively. Teams may be entered in the Seniors, Veterans, Ladies, Mixed or Open categories. There will also this year be a Nordic Walking event, as part of the Medical Service’s initiative “Move more, eat better!” The registration fee is 10 CHF per runner, and each runner will receive a souvenir prize. There will be a programme of entertainment from 12:00 on the arrival area (the lawn in front of Restaurant 1): 12:00 - 12:45  Music from the Old Bottom Street band 12:15 Start of the race 12:45 - 13h Demonstrations by the Fitness club and Dancing club 13:00 Results and prize giving (including a raffle to win an iPad2 3G offered by the Micro club) 13:20 à 14:00 Music from “What’s next” And many information st...

  10. Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

    KAUST Repository

    El Shafie, Ahmed

    2016-07-07

    This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

  11. Optimal Contract Design for Cooperative Relay Incentive Mechanism under Moral Hazard

    Directory of Open Access Journals (Sweden)

    Nan Zhao

    2015-01-01

    Full Text Available Cooperative relay can effectively improve spectrum efficiency by exploiting the spatial diversity in the wireless networks. However, wireless nodes may acquire different network information with various users’ location and mobility, channels’ conditions, and other factors, which results in asymmetric information between the source and the relay nodes (RNs. In this paper, the relay incentive mechanism between relay nodes and the source is investigated under the asymmetric information. By modelling multiuser cooperative relay as a labour market, a contract model with moral hazard for relay incentive is proposed. To effectively incentivize the potential RNs to participate in cooperative relay, the optimization problems are formulated to maximize the source’s utility while meeting the feasible conditions under both symmetric and asymmetric information scenarios. Numerical simulation results demonstrate the effectiveness of the proposed contract design scheme for cooperative relay.

  12. Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

    KAUST Repository

    El Shafie, Ahmed; Salem, Ahmed Sultan; Al-Dhahir, Naofal

    2016-01-01

    This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

  13. A performance analysis in AF full duplex relay selection network

    Science.gov (United States)

    Ngoc, Long Nguyen; Hong, Nhu Nguyen; Loan, Nguyen Thi Phuong; Kieu, Tam Nguyen; Voznak, Miroslav; Zdralek, Jaroslav

    2018-04-01

    This paper studies on the relaying selective matter in amplify-and-forward (AF) cooperation communication with full-duplex (FD) activity. Various relay choice models supposing the present of different instant information are investigated. We examine a maximal relaying choice that optimizes the instant FD channel capacity and asks for global channel state information (CSI) as well as partial CSI learning. To make comparison easy, accurate outage probability clauses and asymptote form of these strategies that give a diversity rank are extracted. From that, we can see clearly that the number of relays, noise factor, the transmittance coefficient as well as the information transfer power had impacted on their performance. Besides, the optimal relay selection (ORS) model can promote than that of the partial relay selection (PRS) model.

  14. STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR DAN GROUND FAULT RELAY (GFR PADA RECLOSER DI SALURAN PENYULANG PENEBEL

    Directory of Open Access Journals (Sweden)

    I Dewa Gde Agung Budhi Udiana

    2017-08-01

    Full Text Available Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR and Ground Fault Relay (GFR. The research was conducted at PT. PLN (Persero South Bali Area Network, INDONESIA on recloser in the feeder line of Penebel. OCR setting between the Relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana still less selective, with time value coordination between average security was still less than 0,2 second. Then OCR setting and GFR relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana was recommended for re-setting in order to minimize disruption and electric power distribution system to be reliable.

  15. Two-way CSI-assisted AF relaying with HPA nonlinearity

    KAUST Repository

    Qi, Jian

    2015-09-11

    In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal-to-noise ratio (SNR) is derived as per the modified system model by taking into account the interference caused by relaying scheme and HPA nonlinearity. The system performance of the considered relaying network is evaluated in terms of average symbol error probability (SEP) in Nakagami-m fading channels, by making use of the moment-generating function (MGF) approach. Numerical results are provided and show the effects of several parameters, such as quadrature amplitude modulation (QAM) order, number of relays, HPA parameters, and Nakagami parameter, on performance. © 2015 IEEE.

  16. Corynebacterium diphtheriae methionine sulfoxide reductase a exploits a unique mycothiol redox relay mechanism.

    Science.gov (United States)

    Tossounian, Maria-Armineh; Pedre, Brandán; Wahni, Khadija; Erdogan, Huriye; Vertommen, Didier; Van Molle, Inge; Messens, Joris

    2015-05-01

    Methionine sulfoxide reductases are conserved enzymes that reduce oxidized methionines in proteins and play a pivotal role in cellular redox signaling. We have unraveled the redox relay mechanisms of methionine sulfoxide reductase A of the pathogen Corynebacterium diphtheriae (Cd-MsrA) and shown that this enzyme is coupled to two independent redox relay pathways. Steady-state kinetics combined with mass spectrometry of Cd-MsrA mutants give a view of the essential cysteine residues for catalysis. Cd-MsrA combines a nucleophilic cysteine sulfenylation reaction with an intramolecular disulfide bond cascade linked to the thioredoxin pathway. Within this cascade, the oxidative equivalents are transferred to the surface of the protein while releasing the reduced substrate. Alternatively, MsrA catalyzes methionine sulfoxide reduction linked to the mycothiol/mycoredoxin-1 pathway. After the nucleophilic cysteine sulfenylation reaction, MsrA forms a mixed disulfide with mycothiol, which is transferred via a thiol disulfide relay mechanism to a second cysteine for reduction by mycoredoxin-1. With x-ray crystallography, we visualize two essential intermediates of the thioredoxin relay mechanism and a cacodylate molecule mimicking the substrate interactions in the active site. The interplay of both redox pathways in redox signaling regulation forms the basis for further research into the oxidative stress response of this pathogen. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

  17. Theoretical Analysis of Proton Relays in Electrochemical Proton-Coupled Electron Transfer

    International Nuclear Information System (INIS)

    Auer, Benjamin; Fernandez, Laura; Hammes-Schiffer, Sharon

    2011-01-01

    The coupling of long-range electron transfer to proton transport over multiple sites plays a vital role in many biological and chemical processes. Recently a molecule with a hydrogen-bond relay inserted between the proton donor and acceptor sites in a proton-coupled electron transfer (PCET) system was studied electrochemically. The standard rate constants and kinetic isotope effects (KIEs) were measured experimentally for this system and a related single proton transfer system. In the present paper, these systems are studied theoretically using vibronically nonadiabatic rate constant expressions for electrochemical PCET. Application of this approach to proton relays requires the calculation of multidimensional proton vibrational wavefunctions and incorporation of multiple proton donor-acceptor motions. The calculated KIEs and relative standard rate constants for the single and double proton transfer systems are in agreement with the experimental data. The calculations indicate that the standard rate constant is lower for the double proton transfer system because of the smaller overlap integral between the ground state reduced and oxidized proton vibrational wavefunctions for this system, resulting in greater contributions from excited electron-proton vibronic states with higher free energy barriers. The decrease in proton donor-acceptor distances due to thermal fluctuations and the contributions from excited electron-proton vibronic states play important roles in proton relay systems. The theory suggests that the PCET rate constant may be increased by decreasing the equilibrium proton donor-acceptor distances or modifying the thermal motions of the molecule to facilitate the concurrent decrease of these distances. The submission of this journal article in ERIA is a requirement of the EFRC subcontract with Pennsylvania State University collaborators to get publications to OSTI.

  18. Spreading Sequence System for Full Connectivity Relay Network

    Science.gov (United States)

    Kwon, Hyuck M. (Inventor); Yang, Jie (Inventor); Pham, Khanh D. (Inventor)

    2018-01-01

    Fully connected uplink and downlink fully connected relay network systems using pseudo-noise spreading and despreading sequences subjected to maximizing the signal-to-interference-plus-noise ratio. The relay network systems comprise one or more transmitting units, relays, and receiving units connected via a communication network. The transmitting units, relays, and receiving units each may include a computer for performing the methods and steps described herein and transceivers for transmitting and/or receiving signals. The computer encodes and/or decodes communication signals via optimum adaptive PN sequences found by employing Cholesky decompositions and singular value decompositions (SVD). The PN sequences employ channel state information (CSI) to more effectively and more securely computing the optimal sequences.

  19. Ka-band Technologies for Small Spacecraft Communications via Relays and Direct Data Downlink

    Science.gov (United States)

    Budinger, James M.; Niederhaus, Charles; Reinhart, Richard; Downey, Joe; Roberts, Anthony

    2016-01-01

    As the scientific capabilities and number of small spacecraft missions in the near Earth region increase, standard yet configurable user spacecraft terminals operating in Ka-band are needed to lower mission cost and risk and enable significantly higher data return than current UHF or S-band terminals. These compact Ka-band terminals are intended to operate with both the current and next generation of Ka-band relay satellites and via direct data communications with near Earth tracking terminals. This presentation provides an overview of emerging NASA-sponsored and commercially provided technologies in software defined radios (SDRs), transceivers, and electronically steered antennas that will enable data rates from hundreds of kbps to over 1 Gbps and operate in multiple frequency bands (such as S- and X-bands) and expand the use of NASA's common Ka-bands frequencies: 22.55-23.15 GHz for forward data or uplink; and 25.5-27.0 GHz for return data or downlink. Reductions in mass, power and volume come from integration of multiple radio functions, operations in Ka-band, high efficiency amplifiers and receivers, and compact, flat and vibration free electronically steered narrow beam antennas for up to + 60 degrees field of regard. The software defined near Earth space transceiver (SD-NEST) described in the presentation is intended to be compliant with NASA's space telecommunications radio system (STRS) standard for communications waveforms and hardware interoperability.

  20. Four-Way Relaying in Wireless Cellular Systems

    DEFF Research Database (Denmark)

    Liu, Huaping; Popovski, Petar; De Carvalho, Elisabeth

    2013-01-01

    Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed in such a way that one RS...... of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with a state-of-the-art reference scheme, based on two-way relaying with DF. The results indicate that the achievable rate regions are significantly enlarged for the new scheme....

  1. Systematic Network Coding with the Aid of a Full-Duplex Relay

    DEFF Research Database (Denmark)

    Giacaglia, Giuliano; Shi, Xiaomeng; Kim, MinJi

    2013-01-01

    is to deliver a given number of data packets to a receiver with the aid of a relay. The source broadcasts to both the receiver and the relay using one frequency, while the relay uses another frequency for transmissions to the receiver, allowing for a full-duplex operation of the relay. We analyze the decoding...... complexity and delay performance of two types of relays: one that preserves the systematic structure of the code from the source; another that does not. A systematic relay forwards uncoded packets upon reception, but transmits coded packets to the receiver after receiving the first coded packet from...

  2. Mobile User Connectivity in Relay-Assisted Visible Light Communications

    Directory of Open Access Journals (Sweden)

    Petr Pešek

    2018-04-01

    Full Text Available In this paper, we investigate relay-assisted visible light communications (VLC where a mobile user acts as a relay and forwards data from a transmitter to the end mobile user. We analyse the utilization of the amplify-and-forward (AF and decode-and-forward (DF relaying schemes. The focus of the paper is on analysis of the behavior of the mobile user acting as a relay while considering a realistic locations of the receivers and transmitters on a standard mobile phone, more specifically with two photodetectors on both sides of a mobile phone and a transmitting LED array located upright. We also investigate dependency of the bit error rate (BER performance on the azimuth and elevation angles of the mobile relay device within a typical office environment. We provide a new analytical description of BER for AF and DF-based relays in VLC. In addition we compare AF and DF-based systems and show that DF offers a marginal improvement in the coverage area with a BER < 10–3 and a data rate of 100 Mb/s. Numerical results also illustrate that relay-based systems offer a significant improvement in terms of the coverage compared to direct non-line of sight VLC links.

  3. 47 CFR 11.20 - State Relay Network.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false State Relay Network. 11.20 Section 11.20... Network. This network is composed of State Relay (SR) sources, leased common carrier communications facilities or any other available communication facilities. The network distributes State EAS messages...

  4. SIMULASI SISTEM KELISTRIKAN KAMAR HOTEL MENGGUNAKAN SMART RELAY

    Directory of Open Access Journals (Sweden)

    I Nyoman Sukarma

    2018-03-01

    Full Text Available Fungsi dari alat key tag atau hotel switch atau key card adalah memutus atau menyambungkan aliran listrik ke dalam suatu area tertentu atau ruang. Key tag memiliki peran penting pada kamar hotel untuk mencegah pemborosan energi pada saat kamar hotel tidak berpenghuni atau belum tersewakan. Untuk itu, penulis merancang simulasi sistem kelistrikan pada kamar hotel yang dikontrol dengan smart relay. Pada simulasi ini digunakan smart relay Zelio Logic buatan Schneider Electric. Pemrograman smart relay ini menggunakan ladder diagram yang disusun menggunakan perangkat lunak ZelioSoft2 dari Schneider Electric. Smart relay menerima sinyal masukan dari sensor, key tag dan sakelar. Sinyal masukan tersebut selanjutnya diproses agar lampu, kotak-kontak, exhaust fan, dan AC (Air Conditioner pada kamar hotel dapat bekerja.

  5. Performance of hybrid-ARQ with incremental redundancy over relay channels

    KAUST Repository

    Chelli, Ali; Alouini, Mohamed-Slim

    2012-01-01

    In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears

  6. Asymptotic analysis for Nakagami-m fading channels with relay selection

    KAUST Repository

    Zhong, Caijun; Wong, Kaikit; Jin, Shi; Alouini, Mohamed-Slim; Ratnarajah, Tharm

    2011-01-01

    In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels

  7. Efficient Resource Scheduling by Exploiting Relay Cache for Cellular Networks

    Directory of Open Access Journals (Sweden)

    Chun He

    2015-01-01

    Full Text Available In relay-enhanced cellular systems, throughput of User Equipment (UE is constrained by the bottleneck of the two-hop link, backhaul link (or the first hop link, and access link (the second hop link. To maximize the throughput, resource allocation should be coordinated between these two hops. A common resource scheduling algorithm, Adaptive Distributed Proportional Fair, only ensures that the throughput of the first hop is greater than or equal to that of the second hop. But it cannot guarantee a good balance of the throughput and fairness between the two hops. In this paper, we propose a Two-Hop Balanced Distributed Scheduling (TBS algorithm by exploiting relay cache for non-real-time data traffic. The evolved Node Basestation (eNB adaptively adjusts the number of Resource Blocks (RBs allocated to the backhaul link and direct links based on the cache information of relays. Each relay allocates RBs for relay UEs based on the size of the relay UE’s Transport Block. We also design a relay UE’s ACK feedback mechanism to update the data at relay cache. Simulation results show that the proposed TBS can effectively improve resource utilization and achieve a good trade-off between system throughput and fairness by balancing the throughput of backhaul and access link.

  8. Wireless Energy Harvesting Two-Way Relay Networks with Hardware Impairments.

    Science.gov (United States)

    Peng, Chunling; Li, Fangwei; Liu, Huaping

    2017-11-13

    This paper considers a wireless energy harvesting two-way relay (TWR) network where the relay has energy-harvesting abilities and the effects of practical hardware impairments are taken into consideration. In particular, power splitting (PS) receiver is adopted at relay to harvests the power it needs for relaying the information between the source nodes from the signals transmitted by the source nodes, and hardware impairments is assumed suffered by each node. We analyze the effect of hardware impairments [-20]on both decode-and-forward (DF) relaying and amplify-and-forward (AF) relaying networks. By utilizing the obtained new expressions of signal-to-noise-plus-distortion ratios, the exact analytical expressions of the achievable sum rate and ergodic capacities for both DF and AF relaying protocols are derived. Additionally, the optimal power splitting (OPS) ratio that maximizes the instantaneous achievable sum rate is formulated and solved for both protocols. The performances of DF and AF protocols are evaluated via numerical results, which also show the effects of various network parameters on the system performance and on the OPS ratio design.

  9. Two-Way Multi-Antenna Relaying with Simultaneous Wireless Information and Power Transfer

    Directory of Open Access Journals (Sweden)

    Thanaphat Srivantana

    2017-03-01

    Full Text Available In this paper, we propose various kinds of two-way multi-antenna relaying with simultaneous wireless information and power transfer (SWIPT and investigate their performance. Specifically, we first consider a two-way relay network where two single-antenna end nodes communicate with each other through a multi-antenna relay node that is energy constrained. This relay node harvests energy from the two end nodes and use the harvested energy for forwarding their information. Six relaying schemes that support the considered network then build on the power splitting-based relaying and time switching-based relaying protocols. The average bit error rates of these schemes are evaluated and compared by computer simulations considering several network parameters, including the number of relay antennas, power splitting ratio, and energy harvesting time. Such evaluation and comparison provide useful insights into the performance of SWIPT-based two-way multi-antenna relaying.

  10. Developing a Domain Model for Relay Circuits

    DEFF Research Database (Denmark)

    Haxthausen, Anne Elisabeth

    2009-01-01

    In this paper we stepwise develop a domain model for relay circuits as used in railway control systems. First we provide an abstract, property-oriented model of networks consisting of components that can be glued together with connectors. This model is strongly inspired by a network model...... for railways madeby Bjørner et.al., however our model is more general: the components can be of any kind and can later be refined to e.g. railway components or circuit components. Then we show how the abstract network model can be refined into an explicit model for relay circuits. The circuit model describes...... the statics as well as the dynamics of relay circuits, i.e. how a relay circuit can be composed legally from electrical components as well as how the components may change state over time. Finally the circuit model is transformed into an executable model, and we show how a concrete circuit can be defined...

  11. Breaking the Myth That Relay Swimming Is Faster Than Individual Swimming.

    Science.gov (United States)

    Skorski, Sabrina; Etxebarria, Naroa; Thompson, Kevin G

    2016-04-01

    To investigate if swimming performance is better in a relay race than in the corresponding individual race. The authors analyzed 166 elite male swimmers from 15 nations in the same competition (downloaded from www.swimrankings.net). Of 778 observed races, 144 were Olympic Games performances (2000, 2004, 2012), with the remaining 634 performed in national or international competitions. The races were 100-m (n = 436) and 200-m (n = 342) freestyle events. Relay performance times for the 2nd-4th swimmers were adjusted (+ 0.73 s) to allow for the "flying start." Without any adjustment, mean individual relay performances were significantly faster for the first 50 m and overall time in the 100-m events. Furthermore, the first 100 m of the 200-m relay was significantly faster (P > .001). During relays, swimmers competing in 1st position did not show any difference compared with their corresponding individual performance (P > .16). However, swimmers competing in 2nd-4th relay-team positions demonstrated significantly faster times in the 100-m (P individual events (P team positions were adjusted for the flying start no differences were detected between relay and individual race performance for any event or split time (P > .17). Highly trained swimmers do not swim (or turn) faster in relay events than in their individual races. Relay exchange times account for the difference observed in individual vs relay performance.

  12. High salinity relay as a post-harvest processing method for reducing Vibrio vulnificus levels in oysters (Crassostrea virginica).

    Science.gov (United States)

    Audemard, Corinne; Kator, Howard I; Reece, Kimberly S

    2018-08-20

    High salinity relay of Eastern oysters (Crassostrea virginica) was evaluated as a post-harvest processing (PHP) method for reducing Vibrio vulnificus. This approach relies on the exposure of oysters to natural high salinity waters and preserves a live product compared to previously approved PHPs. Although results of prior studies evaluating high salinity relay as a means to decrease V. vulnificus levels were promising, validation of this method as a PHP following approved guidelines is required. This study was designed to provide data for validation of this method following Food and Drug Administration (FDA) PHP validation guidelines. During each of 3 relay experiments, oysters cultured from 3 different Chesapeake Bay sites of contrasting salinities (10-21 psu) were relayed without acclimation to high salinity waters (31-33 psu) for up to 28 days. Densities of V. vulnificus and densities of total and pathogenic Vibrio parahaemolyticus (as tdh positive strains) were measured using an MPN-quantitative PCR approach. Overall, 9 lots of oysters were relayed with 6 exhibiting initial V. vulnificus >10,000/g. As recommended by the FDA PHP validation guidelines, these lots reached both the 3.52 log reduction and the levels ranged from 2 to 61% after 28 days of relay. Although the identification of the factors implicated in oyster mortality will require further examination, this study strongly supports the validation of high salinity relay as an effective PHP method to reduce levels of V. vulnificus in oysters to endpoint levels approved for human consumption. Copyright © 2018 Elsevier B.V. All rights reserved.

  13. Scalable DeNoise-and-Forward in Bidirectional Relay Networks

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Krigslund, Rasmus; Popovski, Petar

    2010-01-01

    In this paper a scalable relaying scheme is proposed based on an existing concept called DeNoise-and-Forward, DNF. We call it Scalable DNF, S-DNF, and it targets the scenario with multiple communication flows through a single common relay. The idea of the scheme is to combine packets at the relay...... in order to save transmissions. To ensure decodability at the end-nodes, a priori information about the content of the combined packets must be available. This is gathered during the initial transmissions to the relay. The trade-off between decodability and number of necessary transmissions is analysed...

  14. Sum-Rate Maximization of Coordinated Direct and Relay Systems

    DEFF Research Database (Denmark)

    Sun, Fan; Popovski, Petar; Thai, Chan

    2012-01-01

    Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference and boosting the overall system performance. In this paper we investigate the novel transmission modes, based...... on amplify-and-forward, that arise when the relay is equipped with multiple antennas and can use beamforming. We focus on one representative traffic type, with one uplink and one downlink users and consider the achievable sum-rate maximization relay beamforming. The beamforming criterion leads to a non...

  15. Effects of relay chatter in seismic probabilistic safety analysis

    International Nuclear Information System (INIS)

    Reed, J.W.; Shiu, K.K.

    1985-01-01

    In the Zion and Indian Point Probabilistic Safety Studies, relay chatter was dismissed as a credible event and hence was not formally included in the analyses. Although little discussion is given in the Zion and Indian Point PSA documentation concerning the basis for this decision, it has been expressed informally that it was assumed that the operators will be able to reset all relays in a timely manner. Currently, it is the opinion of many professionals that this may be an oversimplification. The three basic areas which must be considered in addressing relay chatter include the fragility of the relays per se, the reliability of the operators to reset the relays and finally the systems response aspects. Each of these areas is reviewed and the implications for seismic PSA are discussed. Finally, recommendations for future research are given

  16. Relay communications strategies for Mars exploration through 2020

    Science.gov (United States)

    Edwards, Charles D., Jr.; Arnold, B.; DePaula, R.; Kazz, G.; Lee, C.; Noreen, G.

    2005-01-01

    In this paper we will examine NASA's strategy for relay communications support of missions planned for this decade, and discuss options for longer-term relay network evolution in support of second-decade missions.

  17. On the evaluation of Web Radio

    OpenAIRE

    Field, A.N.; Hartel, Pieter H.

    2001-01-01

    We develop an evaluation method for Web radio, and perform it to see what we can be learnt about seven prominent Web radio sites. We also evaluate a commercial FM radio station for control purposes. We present a taxonomy of Web radio, and we give our observations and conclusions on this evaluation.

  18. 76 FR 65965 - Contributions to the Telecommunications Relay Services Fund

    Science.gov (United States)

    2011-10-25

    ...] Contributions to the Telecommunications Relay Services Fund AGENCY: Federal Communications Commission. ACTION... Telecommunications Relay Services (TRS) Fund in a manner prescribed by regulation that is consistent with and... . SUPPLEMENTARY INFORMATION: This is a summary of the Commission's Contributions to the Telecommunications Relay...

  19. Switched diversity strategies for dual-hop relaying systems

    KAUST Repository

    Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

    2011-01-01

    This paper investigates the effect of different switched diversity configurations on the implementation complexity and achieved performance of dual-hop amplify-and-forward (AF) relaying networks. A low-complexity model of the relay station

  20. Relay selection in underlay cognitive networks with fixed transmission power nodes

    KAUST Repository

    Hussain, Syed Imtiaz

    2013-07-31

    Underlay cognitive networks operate simultaneously with primary networks satisfying stringent interference constraints, which reduces their transmission power and coverage area. To reach remote destinations, secondary sources use relaying techniques. Selecting the best relay among the available ones is a well known technique. Recently, selective cooperation is investigated in cognitive networks where the secondary nodes can adapt their transmission power to always satisfy the interference threshold. In this paper, we investigate a situation where the secondary nodes have a fixed transmission power and may violate the interference threshold. We present two relay selection schemes; the first one excludes the relays not satisfying the interference constraint and then picks up a relay from the remaining ones that can provide the maximum signal-to-noise ratio (SNR). The other scheme uses a quotient of the relay link SNR and the interference from the relay to the primary user and optimizes it to maximise the relay link SNR. We derive closed form expressions for outage probability, bit error rate, channel capacity and diversity of the system for both schemes by using tight approximations. We also study mutual effects of interference. Simulation results confirm the analytical results and reveal that the relay selection is feasible at low SNRs. Copyright © 2013 John Wiley & Sons, Ltd.

  1. Bilayer Protograph Codes for Half-Duplex Relay Channels

    Science.gov (United States)

    Divsalar, Dariush; VanNguyen, Thuy; Nosratinia, Aria

    2013-01-01

    Direct to Earth return links are limited by the size and power of lander devices. A standard alternative is provided by a two-hops return link: a proximity link (from lander to orbiter relay) and a deep-space link (from orbiter relay to Earth). Although direct to Earth return links are limited by the size and power of lander devices, using an additional link and a proposed coding for relay channels, one can obtain a more reliable signal. Although significant progress has been made in the relay coding problem, existing codes must be painstakingly optimized to match to a single set of channel conditions, many of them do not offer easy encoding, and most of them do not have structured design. A high-performing LDPC (low-density parity-check) code for the relay channel addresses simultaneously two important issues: a code structure that allows low encoding complexity, and a flexible rate-compatible code that allows matching to various channel conditions. Most of the previous high-performance LDPC codes for the relay channel are tightly optimized for a given channel quality, and are not easily adapted without extensive re-optimization for various channel conditions. This code for the relay channel combines structured design and easy encoding with rate compatibility to allow adaptation to the three links involved in the relay channel, and furthermore offers very good performance. The proposed code is constructed by synthesizing a bilayer structure with a pro to graph. In addition to the contribution to relay encoding, an improved family of protograph codes was produced for the point-to-point AWGN (additive white Gaussian noise) channel whose high-rate members enjoy thresholds that are within 0.07 dB of capacity. These LDPC relay codes address three important issues in an integrative manner: low encoding complexity, modular structure allowing for easy design, and rate compatibility so that the code can be easily matched to a variety of channel conditions without extensive

  2. Implementation of a Relay Coordination System for the Mars Network

    Science.gov (United States)

    Allard, Daniel A.

    2010-01-01

    Mars network relay operations involve the coordination of lander and orbiter teams through long-term and short-term planning, tactical changes and post-pass analysis. Much of this coordination is managed through email traffic and point-to-point file data exchanges. It is often difficult to construct a complete and accurate picture of the relay situation at any given moment, as there is no centralized store of correlated relay data. The Mars Relay Operations Service (MaROS) is being implemented to address the problem of relay coordination for current and next-generation relay missions. The service is provided for the purpose of coordinating communications sessions between landed spacecraft assets and orbiting spacecraft assets at Mars. The service centralizes a set of functions previously distributed across multiple spacecraft operations teams, and as such greatly improves visibility into the end-to-end strategic coordination process. Most of the process revolves around the scheduling of communications sessions between the spacecraft during periods of time when a landed asset on Mars is geometrically visible by an orbiting spacecraft. These "relay" sessions are used to transfer data both to and from the landed asset via the orbiting asset on behalf of Earth-based spacecraft operators. This paper will discuss the relay coordination problem space, overview the architecture and design selected to meet system requirements, and describe the first phase of system implementation

  3. Screening test of relays used under pressurized sulfur hexafluoride (SF6)

    International Nuclear Information System (INIS)

    Kutsukake, Kenichi; Matsuda, Makoto; Hanashima, Susumu; Obara, Kenjiro

    2008-01-01

    Many measurement and control devices inside of a high voltage terminal of the JAEA-Tokai tandem accelerator are operated under pressurized sulfur hexafluoride gas (SF 6 ) of 0.5 MPa. This screening test has been carried out to select a relay, which is usable under the pressurized SF 6 for turn on and off a large current of the devices, from commercial relays used in the atmospheric condition. Four kinds of relays were tested: electromechanical relay (EMR), magnet contactor (MAG), solid-state relay (SSR) and hybrid relay (HYB). Temperature and appearance changes of the relay were collected as measurement items. In addition, a reason of contact trouble of the relays was considered from the results of qualitative elementary analysis and observation of the contact surface using the EDS (energy-dispersive X-ray spectroscopy) and the SEM (scanning electron microscope). As a result, the EMR and the MAG showed irregular contact in spite of input voltage and electric current had fed to an operational coil of the relay normally. It is caused by the sulfide or fluoride compounds, which were formed by chemical reaction between metals and sulfur or hydrogen fluoride due to dissociation of SF 6 in electric arcs. On the other hand, the performance of the SSR and the HYB is better than the EMR and the MAG, and it was found that these relays are available in the pressurized SF 6 of 0.5MPa in spite of the standard specification. (author)

  4. Relay-based information broadcast in complex networks

    Science.gov (United States)

    Fan, Zhongyan; Han, Zeyu; Tang, Wallace K. S.; Lin, Dong

    2018-04-01

    Information broadcast (IB) is a critical process in complex network, usually accomplished by flooding mechanism. Although flooding is simple and no prior topological information is required, it consumes a lot of transmission overhead. Another extreme is the tree-based broadcast (TB), for which information is disseminated via a spanning tree. It achieves the minimal transmission overhead but the maintenance of spanning tree for every node is an obvious obstacle for implementation. Motivated by the success of scale-free network models for real-world networks, in this paper, we investigate the issues in IB by considering an alternative solution in-between these two extremes. A novel relay-based broadcast (RB) mechanism is proposed by employing a subset of nodes as relays. Information is firstly forwarded to one of these relays and then re-disseminated to others through the spanning tree whose root is the relay. This mechanism provides a trade-off solution between flooding and TB. On one hand, it saves up a lot of transmission overhead as compared to flooding; on the other hand, it costs much less resource for maintenance than TB as only a few spanning trees are needed. Based on two major criteria, namely the transmission overhead and the convergence time, the effectiveness of RB is confirmed. The impacts of relay assignment and network structures on performance are also studied in this work.

  5. Performance evaluation of cognitive radio in advanced metering infrastructure communication

    Science.gov (United States)

    Hiew, Yik-Kuan; Mohd Aripin, Norazizah; Din, Norashidah Md

    2016-03-01

    Smart grid is an intelligent electricity grid system. A reliable two-way communication system is required to transmit both critical and non-critical smart grid data. However, it is difficult to locate a huge chunk of dedicated spectrum for smart grid communications. Hence, cognitive radio based communication is applied. Cognitive radio allows smart grid users to access licensed spectrums opportunistically with the constraint of not causing harmful interference to licensed users. In this paper, a cognitive radio based smart grid communication framework is proposed. Smart grid framework consists of Home Area Network (HAN) and Advanced Metering Infrastructure (AMI), while AMI is made up of Neighborhood Area Network (NAN) and Wide Area Network (WAN). In this paper, the authors only report the findings for AMI communication. AMI is smart grid domain that comprises smart meters, data aggregator unit, and billing center. Meter data are collected by smart meters and transmitted to data aggregator unit by using cognitive 802.11 technique; data aggregator unit then relays the data to billing center using cognitive WiMAX and TV white space. The performance of cognitive radio in AMI communication is investigated using Network Simulator 2. Simulation results show that cognitive radio improves the latency and throughput performances of AMI. Besides, cognitive radio also improves spectrum utilization efficiency of WiMAX band from 5.92% to 9.24% and duty cycle of TV band from 6.6% to 10.77%.

  6. Cooperative relay-based multicasting for energy and delay minimization

    KAUST Repository

    Atat, Rachad

    2012-08-01

    Relay-based multicasting for the purpose of cooperative content distribution is studied. Optimized relay selection is performed with the objective of minimizing the energy consumption or the content distribution delay within a cluster of cooperating mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles that were not able to receive the multicast data. Both schemes show significant superiority compared to the non-cooperative scenarios, in terms of energy consumption and delay reduction. © 2012 IEEE.

  7. Radio Frequency Interference: The Study of Rain Effect on Radio Signal Attenuation

    International Nuclear Information System (INIS)

    Roslan Umar; Roslan Umar; Shahirah Syafa Sulan; Atiq Wahidah Azlan; Zainol Abidin Ibrahim

    2015-01-01

    The intensity of radio waves received by radio telescopes is always not subject to human control. In the millimetre band, the propagation of the electromagnetic waves is severely affected by rain rate, dust particle size and drop size in the terms of attenuation, noise and depolarization. At the frequency above 10 GHz, the absorption and scattering by rain cause a reduction in the transmitted signal amplitude which will lead to the reducing of the availability, reliability and performance on the communications link. In this study, the rain effect on radio signal has been investigated. Spectrum analyzer and weather stations were used to obtain the RFI level and rain rate data respectively. The radio frequency interference (RFI) pattern due to rain factor was determined. This will benefit radio astronomer in managing sites for radio observation for radio astronomy purposes. (author)

  8. IRC on your dime? What you really need to know about Internet relay chat

    Energy Technology Data Exchange (ETDEWEB)

    ERayome, J.; Romig, S., LLNL

    1998-05-22

    The purpose of this paper is to describe recent trends CIAC has encountered while working with sites that have been compromised. Frequently, the intruders set up and run Internet Relay Chat (IRC) to exchange information and to show off their success at having compromised a site. Invariably, this protocol consumes bandwidth, uses CPU cycles and is a source of embarrassment for the site. This paper focuses on these negative aspects of IRC and concedes that one can cite numerous examples where IRC is used in a positive manner.

  9. Secure relay selection based on learning with negative externality in wireless networks

    Science.gov (United States)

    Zhao, Caidan; Xiao, Liang; Kang, Shan; Chen, Guiquan; Li, Yunzhou; Huang, Lianfen

    2013-12-01

    In this paper, we formulate relay selection into a Chinese restaurant game. A secure relay selection strategy is proposed for a wireless network, where multiple source nodes send messages to their destination nodes via several relay nodes, which have different processing and transmission capabilities as well as security properties. The relay selection utilizes a learning-based algorithm for the source nodes to reach their best responses in the Chinese restaurant game. In particular, the relay selection takes into account the negative externality of relay sharing among the source nodes, which learn the capabilities and security properties of relay nodes according to the current signals and the signal history. Simulation results show that this strategy improves the user utility and the overall security performance in wireless networks. In addition, the relay strategy is robust against the signal errors and deviations of some user from the desired actions.

  10. Effect of RF Interference on the Security-Reliability Trade-off Analysis of Multiuser Mixed RF/FSO Relay Networks with Power Allocation

    KAUST Repository

    Abd El-Malek, Ahmed

    2017-03-27

    In this paper, the impact of radio frequency (RF) cochannel interference (CCI) on the performance of multiuser mixed RF/free-space optical (FSO) relay network with opportunistic user scheduling under eavesdropping attack is studied. The considered system includes multiple users, one decode-and-forward relay, one destination, and an eavesdropper. In the analysis, the RF/FSO channels follow Nakagami-m/Gamma-Gamma fading models, respectively, with pointing errors on the FSO link. Exact closed-form expression for the system outage probability is derived. Then, an asymptotic expression for the outage probability is obtained at the high signal-to-interference-plus-noise ratio regime to get more insights on the system performance. Moreover, the obtained results are used to find the optimal transmission power in different turbulence conditions. The secrecy performance is studied in the presence of CCI at both the authorized relay and eavesdropper, where closed-form expressions are derived for the intercept probability. The physical layer security performance is enhanced using cooperative jamming models, where new closed-form expressions are derived for the intercept probability. Another power allocation optimization problem is formulated to find the optimal transmission and jamming powers. The derived analytical formulas are supported by numerical results to clarify the main contributions of this paper.

  11. Proof-of-Work as Anonymous Micropayment: Rewarding a Tor Relay

    OpenAIRE

    Biryukov, Alex; Pustogarov, Ivan

    2015-01-01

    In this paper we propose a new micropayments scheme which can be used to reward Tor relay operators. Tor clients do not pay Tor relays with electronic cash directly but submit proof of work shares which the relays can resubmit to a crypto-currency mining pool. Relays credit users who submit shares with tickets that can later be used to purchase improved service. Both shares and tickets when sent over Tor circuits are anonymous. The analysis of the crypto-currencies market prices shows that th...

  12. Error-rate performance analysis of opportunistic regenerative relaying

    KAUST Repository

    Tourki, Kamel

    2011-09-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can be considered unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation where the detector may use maximum ration combining (MRC) or selection combining (SC). Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network (LN) architecture and considering Rayleigh fading channels. © 2011 IEEE.

  13. Securing Relay Networks with Artificial Noise: An Error Performance-Based Approach

    Directory of Open Access Journals (Sweden)

    Ying Liu

    2017-07-01

    Full Text Available We apply the concept of artificial and controlled interference in a two-hop relay network with an untrusted relay, aiming at enhancing the wireless communication secrecy between the source and the destination node. In order to shield the square quadrature amplitude-modulated (QAM signals transmitted from the source node to the relay, the destination node designs and transmits artificial noise (AN symbols to jam the relay reception. The objective of our considered AN design is to degrade the error probability performance at the untrusted relay, for different types of channel state information (CSI at the destination. By considering perfect knowledge of the instantaneous CSI of the source-to-relay and relay-to-destination links, we first present an analytical expression for the symbol error rate (SER performance at the relay. Based on the assumption of an average power constraint at the destination node, we then derive the optimal phase and power distribution of the AN that maximizes the SER at the relay. Furthermore, we obtain the optimal AN design for the case where only statistical CSI is available at the destination node. For both cases, our study reveals that the Gaussian distribution is generally not optimal to generate AN symbols. The presented AN design takes into account practical parameters for the communication links, such as QAM signaling and maximum likelihood decoding.

  14. Efficient incremental relaying for packet transmission over fading channels

    KAUST Repository

    Fareed, Muhammad Mehboob

    2014-07-01

    In this paper, we propose a novel relaying scheme for packet transmission over fading channels, which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from the destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying (EIR) scheme with both amplify and forward and decode and forward relaying. We compare the performance of the EIR scheme with the threshold-based incremental relaying (TIR) scheme. It is shown that the efficiency of the TIR scheme is better for lower values of the threshold. However, the efficiency of the TIR scheme for higher values of threshold is outperformed by the EIR. In addition, three new threshold-based adaptive EIR are devised to further improve the efficiency of the EIR scheme. We calculate the packet error rate and the efficiency of these new schemes to provide the analytical insight. © 2014 IEEE.

  15. Relay discovery and selection for large-scale P2P streaming.

    Directory of Open Access Journals (Sweden)

    Chengwei Zhang

    Full Text Available In peer-to-peer networks, application relays have been commonly used to provide various networking services. The service performance often improves significantly if a relay is selected appropriately based on its network location. In this paper, we studied the location-aware relay discovery and selection problem for large-scale P2P streaming networks. In these large-scale and dynamic overlays, it incurs significant communication and computation cost to discover a sufficiently large relay candidate set and further to select one relay with good performance. The network location can be measured directly or indirectly with the tradeoffs between timeliness, overhead and accuracy. Based on a measurement study and the associated error analysis, we demonstrate that indirect measurements, such as King and Internet Coordinate Systems (ICS, can only achieve a coarse estimation of peers' network location and those methods based on pure indirect measurements cannot lead to a good relay selection. We also demonstrate that there exists significant error amplification of the commonly used "best-out-of-K" selection methodology using three RTT data sets publicly available. We propose a two-phase approach to achieve efficient relay discovery and accurate relay selection. Indirect measurements are used to narrow down a small number of high-quality relay candidates and the final relay selection is refined based on direct probing. This two-phase approach enjoys an efficient implementation using the Distributed-Hash-Table (DHT. When the DHT is constructed, the node keys carry the location information and they are generated scalably using indirect measurements, such as the ICS coordinates. The relay discovery is achieved efficiently utilizing the DHT-based search. We evaluated various aspects of this DHT-based approach, including the DHT indexing procedure, key generation under peer churn and message costs.

  16. Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

    OpenAIRE

    Y. Damchi; J. Sadeh; H. Rajabi Mashhadi

    2015-01-01

    Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs). Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determi...

  17. Microcomputer relay regulator in the CAMAC standard

    International Nuclear Information System (INIS)

    Nikolaev, V.P.

    1984-01-01

    The digital relay regulator is developed on the base of the KM001 microcomputer and KK06 controller for automatic control ob ects with transfer functions describing a broad class of systems using actuating motors (stabilitation, follow-up systems). The CAMAC relay-unit realizes the regulation law and provides the possibility to control analogous values by 8 channels

  18. Coordination of Regenerative Relays and Direct Users in Wireless Cellular Networks

    DEFF Research Database (Denmark)

    Thai, Chan; Popovski, Petar

    2011-01-01

    The area of wireless cooperation/relaying has recently been significantly enriched by the ideas of wireless network coding (NC), which bring substantial gains in spectral efficiency. These gains have mainly been demonstrated in scenarios with two-way relaying. Inspired by the ideas of wireless NC......, recently we have proposed techniques for coordinated direct/relay (CDR) transmissions. These techniques embrace the interference among the communication flows to/from direct and relayed users, leveraging on the fact that the interference can be subsequently canceled. Hence, by allowing simultaneous...... transmissions, spectral efficiency is increased. In our prior work, we have considered CDR with non-regenerative relay that uses Amplify-and-Forward (AF). In this paper we consider the case of regenerative Decode-and-Forward (DF) relay. This refers also to joint decoding of the interfering flows received over...

  19. Admission Control Threshold in Cellular Relay Networks with Power Adjustment

    Directory of Open Access Journals (Sweden)

    Lee Ki-Dong

    2009-01-01

    Full Text Available Abstract In the cellular network with relays, the mobile station can benefit from both coverage extension and capacity enhancement. However, the operation complexity increases as the number of relays grows up. Furthermore, in the cellular network with cooperative relays, it is even more complex because of an increased dimension of signal-to-noise ratios (SNRs formed in the cooperative wireless transmission links. In this paper, we propose a new method for admission capacity planning in a cellular network using a cooperative relaying mechanism called decode-and-forward. We mathematically formulate the dropping ratio using the randomness of "channel gain." With this, we formulate an admission threshold planning problem as a simple optimization problem, where we maximize the accommodation capacity (in number of connections subject to two types of constraints. (1 A constraint that the sum of the transmit powers of the source node and relay node is upper-bounded where both nodes can jointly adjust the transmit power. (2 A constraint that the dropping ratio is upper-bounded by a certain threshold value. The simplicity of the problem formulation facilitates its solution in real-time. We believe that the proposed planning method can provide an attractive guideline for dimensioning a cellular relay network with cooperative relays.

  20. Implementation of a microcomputer based distance relay for parallel transmission lines

    International Nuclear Information System (INIS)

    Phadke, A.G.; Jihuang, L.

    1986-01-01

    Distance relaying for parallel transmission lines is a difficult application problem with conventional phase and ground distance relays. It is known that for cross-country faults involving dissimilar phases and ground, three phase tripping may result. This paper summarizes a newly developed microcomputer based relay which is capable of classifying the cross-country fault correctly. The paper describes the principle of operation and results of laboratory tests of this relay

  1. Performance Analysis of Selective Decode-and-Forward Multinode Incremental Relaying with Maximal Ratio Combining

    KAUST Repository

    Hadjtaieb, Amir

    2013-09-12

    In this paper, we propose an incremental multinode relaying protocol with arbitrary N-relay nodes that allows an efficient use of the channel spectrum. The destination combines the received signals from the source and the relays using maximal ratio Combining (MRC). The transmission ends successfully once the accumulated signal-to-noise ratio (SNR) exceeds a predefined threshold. The number of relays participating in the transmission is adapted to the channel conditions based on the feedback from the destination. The use of incremental relaying allows obtaining a higher spectral efficiency. Moreover, the symbol error probability (SEP) performance is enhanced by using MRC at the relays. The use of MRC at the relays implies that each relay overhears the signals from the source and all previous relays and combines them using MRC. The proposed protocol differs from most of existing relaying protocol by the fact that it combines both incremental relaying and MRC at the relays for a multinode topology. Our analyses for a decode-and-forward mode show that: (i) compared to existing multinode relaying schemes, the proposed scheme can essentially achieve the same SEP performance but with less average number of time slots, (ii) compared to schemes without MRC at the relays, the proposed scheme can approximately achieve a 3 dB gain.

  2. Protective relaying of power systems using mathematical morphology

    CERN Document Server

    Wu, QH; Ji, TY

    2009-01-01

    Discusses the development of novel protective relaying algorithms, using Mathematical Morphology (MM). This book introduces the fundamental principles of MM, and brings together the applications of MM to develop different protective relaying algorithms for the protection of a variety of power system components.

  3. Novel Material Integration for Reliable and Energy-Efficient NEM Relay Technology

    Science.gov (United States)

    Chen, I.-Ru

    Energy-efficient switching devices have become ever more important with the emergence of ubiquitous computing. NEM relays are promising to complement CMOS transistors as circuit building blocks for future ultra-low-power information processing, and as such have recently attracted significant attention from the semiconductor industry and researchers. Relay technology potentially can overcome the energy efficiency limit for conventional CMOS technology due to several key characteristics, including zero OFF-state leakage, abrupt switching behavior, and potentially very low active energy consumption. However, two key issues must be addressed for relay technology to reach its full potential: surface oxide formation at the contacting surfaces leading to increased ON-state resistance after switching, and high switching voltages due to strain gradient present within the relay structure. This dissertation advances NEM relay technology by investigating solutions to both of these pressing issues. Ruthenium, whose native oxide is conductive, is proposed as the contacting material to improve relay ON-state resistance stability. Ruthenium-contact relays are fabricated after overcoming several process integration challenges, and show superior ON-state resistance stability in electrical measurements and extended device lifetime. The relay structural film is optimized via stress matching among all layers within the structure, to provide lower strain gradient (below 10E-3/microm -1) and hence lower switching voltage. These advancements in relay technology, along with the integration of a metallic interconnect layer, enable complex relay-based circuit demonstration. In addition to the experimental efforts, this dissertation theoretically analyzes the energy efficiency limit of a NEM switch, which is generally believed to be limited by the surface adhesion energy. New compact (electronic device technology.

  4. A Stochastic Geometry Approach to Full-Duplex MIMO Relay Network

    Directory of Open Access Journals (Sweden)

    Mhd Nour Hindia

    2018-01-01

    Full Text Available Cellular networks are extensively modeled by placing the base stations on a grid, with relays and destinations being placed deterministically. These networks are idealized for not considering the interferences when evaluating the coverage/outage and capacity. Realistic models that can overcome such limitation are desirable. Specifically, in a cellular downlink environment, the full-duplex (FD relaying and destination are prone to interferences from unintended sources and relays. However, this paper considered two-hop cellular network in which the mobile nodes aid the sources by relaying the signal to the dead zone. Further, we model the locations of the sources, relays, and destination nodes as a point process on the plane and analyze the performance of two different hops in the downlink. Then, we obtain the success probability and the ergodic capacity of the two-hop MIMO relay scheme, accounting for the interference from all other adjacent cells. We deploy stochastic geometry and point process theory to rigorously analyze the two-hop scheme with/without interference cancellation. These attained expressions are amenable to numerical evaluation and are corroborated by simulation results.

  5. Minimax robust relay selection based on uncertain long-term CSI

    KAUST Repository

    Nisar, Muhammad Danish

    2014-02-01

    Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot-based transmission or distributed space-time (ST) code implementation. Dynamically selecting a single best relay out of multiple relays and then using it alone for cooperative transmission alleviates the need for this strong coordination while still reaping the benefits of increased diversity and coverage. In this paper, we consider the design of relay selection (RS) under an imperfect knowledge of long-term channel state information (CSI) at the relay nodes, and we pursue minimax optimization to arrive at a robust RS approach that promises the best guarantee on the worst-case end-to-end signal-to-noise ratio (SNR). We provide some intuitive examples and extensive simulation results, not only in terms of worst-case SNR performance but also in terms of average bit-error-rate (BER) performance, to demonstrate the benefits of the proposed minimax robust RS scheme. © 2013 IEEE.

  6. Quasi-period oscillations of relay feedback systems

    International Nuclear Information System (INIS)

    Wen Guilin; Wang Qingguo; Lee, T.H.

    2007-01-01

    This paper presents an analytical method for investigation of the existence and stability of quasi-period oscillations (torus solutions) for a class of relay feedback systems. The idea is to analyze Poincare map from one switching surface to the next based on the Hopf bifurcation theory of maps. It is shown that there exist quasi-period oscillations in certain relay feedback systems

  7. Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

    KAUST Repository

    Park, Seongho

    2011-12-01

    In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can eliminate the inter-relay interference resulted from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2011 IEEE.

  8. Best relay selection using SNR and interference quotient for underlay cognitive networks

    KAUST Repository

    Hussain, Syed Imtiaz

    2012-06-01

    Cognitive networks in underlay settings operate simultaneously with the primary networks satisfying stringent interference limits. This condition forces them to operate with low transmission powers and confines their area of coverage. In an effort to reach remote destinations, underlay cognitive sources make use of relaying techniques. Selecting the best relay among those who are ready to cooperate is different in underlay settings than traditional non-cognitive networks. In this paper, we present a relay selection scheme which uses the quotient of the relay link signal to noise ratio (SNR) and the interference generated from the relay to the primary user to choose the best relay. The proposed scheme optimizes this quotient in a way to maximize the relay link SNR above a certain value whereas the interference is kept below a defined threshold. We derive closed expressions for the outage probability and bit error probability of the system incorporating this scheme. Simulation results confirm the validity of the analytical results and reveal that the relay selection in cognitive environment is feasible in low SNR regions. © 2012 IEEE.

  9. Adaptive transmission based on multi-relay selection and rate-compatible LDPC codes

    Science.gov (United States)

    Su, Hualing; He, Yucheng; Zhou, Lin

    2017-08-01

    In order to adapt to the dynamical changeable channel condition and improve the transmissive reliability of the system, a cooperation system of rate-compatible low density parity check (RC-LDPC) codes combining with multi-relay selection protocol is proposed. In traditional relay selection protocol, only the channel state information (CSI) of source-relay and the CSI of relay-destination has been considered. The multi-relay selection protocol proposed by this paper takes the CSI between relays into extra account in order to obtain more chances of collabration. Additionally, the idea of hybrid automatic request retransmission (HARQ) and rate-compatible are introduced. Simulation results show that the transmissive reliability of the system can be significantly improved by the proposed protocol.

  10. 77 FR 16435 - Transmission Relay Loadability Reliability Standard

    Science.gov (United States)

    2012-03-21

    ... conditions on all applicable transmission lines and transformers. I. Background A. Relay Protection Systems 2... and a power swing. If a power swing is detected, the protection system, ``blocks,'' or prevents the... to the reliability of the Bulk-Power System by requiring load-responsive phase protection relay...

  11. 76 FR 58424 - Transmission Relay Loadability Reliability Standard

    Science.gov (United States)

    2011-09-21

    ... distribution providers to set load-responsive phase protection relays according to specific criteria to ensure...-part R.1.10 allows transmission owners, generation owners and distribution providers to set transformer.... Thus, requiring that transformer fault protection relays are set to not expose the transformer to a...

  12. Development of a Relay Performance Web Tool for the Mars Network

    Science.gov (United States)

    Allard, Daniel A.; Edwards, Charles D.

    2009-01-01

    Modern Mars surface missions rely upon orbiting spacecraft to relay communications to and from Earth systems. An important component of this multi-mission relay process is the collection of relay performance statistics supporting strategic trend analysis and tactical anomaly identification and tracking.

  13. On hybrid cooperation in underlay cognitive radio networks

    KAUST Repository

    Mahmood, Nurul Huda

    2013-09-01

    Cooperative communication is a promising strategy to enhance the performance of a communication network as it helps to improve the coverage area and the outage performance. However, such enhancement comes at the expense of increased resource utilization, which is undesirable; more so in the case of opportunistic wireless systems such as cognitive radio networks. In order to balance the performance gains from cooperative communication against the possible over-utilization of resources, we propose and analyze an adaptive-cooperation technique for underlay cognitive radio networks, termed as hybrid-cooperation. Under the proposed cooperation scheme, secondary users in a cognitive radio network cooperate adaptively to enhance the spectral efficiency and the error performance of the network. The bit error rate, the spectral efficiency and the outage performance of the network under the proposed hybrid cooperation scheme with amplify-and-forward relaying are analyzed in this paper, and compared against conventional cooperation technique. Findings of the analytical performance analyses are further validated numerically through selected computer-based Monte-Carlo simulations. The proposed scheme is found to achieve significantly better performance in terms of the spectral efficiency and the bit error rate, compared to the conventional amplify-and-forward cooperation scheme. © 2013 IEEE.

  14. Micro-relay technology for energy-efficient integrated circuits

    CERN Document Server

    Kam, Hei

    2015-01-01

    This book describes the design of relay-based circuit systems from device fabrication to circuit micro-architectures. This book is ideal for both device engineers as well as circuit system designers and highlights the importance of co-design across design hierarchies when optimizing system performance (in this case, energy-efficiency). This book is ideal for researchers and engineers focused on semiconductors, integrated circuits, and energy efficient electronics. This book also: ·         Covers microsystem fabrication, MEMS device design, circuit design, circuit micro-architecture, and CAD ·         Describes work previously done in the field and also lays the groundwork and criteria for future energy-efficient device and system design ·         Maximizes reader insights into the design and modeling of micro-relay, micro-relay reliability, integrated circuit design with micro-relays, and more

  15. Linear Processing Design of Amplify-and-Forward Relays for Maximizing the System Throughput

    Directory of Open Access Journals (Sweden)

    Qiang Wang

    2018-01-01

    Full Text Available In this paper, firstly, we study the linear processing of amplify-and-forward (AF relays for the multiple relays multiple users scenario. We regard all relays as one special “relay”, and then the subcarrier pairing, relay selection and channel assignment can be seen as a linear processing of the special “relay”. Under fixed power allocation, the linear processing of AF relays can be regarded as a permutation matrix. Employing the partitioned matrix, we propose an optimal linear processing design for AF relays to find the optimal permutation matrix based on the sorting of the received SNR over the subcarriers from BS to relays and from relays to users, respectively. Then, we prove the optimality of the proposed linear processing scheme. Through the proposed linear processing scheme, we can obtain the optimal subcarrier paring, relay selection and channel assignment under given power allocation in polynomial time. Finally, we propose an iterative algorithm based on the proposed linear processing scheme and Lagrange dual domain method to jointly optimize the joint optimization problem involving the subcarrier paring, relay selection, channel assignment and power allocation. Simulation results illustrate that the proposed algorithm can achieve a perfect performance.

  16. A study on Relay Effect via Magnetic Resonant Coupling for Wireless Power Transfer

    Directory of Open Access Journals (Sweden)

    Rashid N.A.

    2016-01-01

    Full Text Available Wireless power transfer (WPT transmits electrical energy from a power source to an electrical load wirelessly or without any conductors. The capability of WPT to transmit the energy is limited. Therefore, a relay was introduced to increase the distance of the WPT capabilities. The effect of the relay has been investigated to extend the energy transfer distance. The effect of relay was demonstrated by placing a relay coil between transmitter and receiver, relay biased to transmitter and placing two relay coils in the designed system. Experimental results are provided to prove the concept of the relay effect. The power transmission efficiency can be achieved up to 75% at 1 meter distance.

  17. The impact of SFCL and SMES integration on the distance relay

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jun, E-mail: JYang@whu.edu.cn [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Zhang, Liling; Wang, Xinpu; Chen, Lei [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Chen, Yanxia [Beijing Electric Power Research Institute, Beijing 100075 (China)

    2016-11-15

    Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

  18. The impact of SFCL and SMES integration on the distance relay

    International Nuclear Information System (INIS)

    Yang, Jun; Zhang, Liling; Wang, Xinpu; Chen, Lei; Chen, Yanxia

    2016-01-01

    Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

  19. Cooperation schemes for rate enhancement in detect-and-forward relay channels

    KAUST Repository

    Benjillali, Mustapha

    2010-05-01

    To improve the spectral efficiency of "Detect-and-Forward" (DetF) half-duplex relaying in fading channels, we propose a cooperation scheme where the relay uses a modulation whose order is higher than the one at the source. In a new common framework, we show that the proposed scheme offers considerable gains - in terms of achievable information rates - compared to the conventional DetF relaying schemes for both orthogonal and non-orthogonal source/relay cooperation. This allows us to propose an adaptive cooperation scheme based on the maximization of the information rate at the destination which needs to observe only the average signal-to-noise ratios of direct and relaying links. ©2010 IEEE.

  20. IEEE C37.98-1987: IEEE standard seismic testing of relays

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in IEEE Std 344-1987. To define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general, they are (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay that constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new application, then proof testing must be performed for that new case

  1. IEEE C37.98-1978: IEEE standard seismic testing of relays

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in ANSI/IEEE Std 344-1975, Recommended Practices for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations. In order to define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general they are: (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay which constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new case

  2. Modeling and Simulation of Out of Step Blocking Relay for

    Directory of Open Access Journals (Sweden)

    Ahmed A. Al Adwani

    2013-05-01

    Full Text Available  This paper investigates a power swing effect on a distance protection relay performance installed on (HV/EHV transmission line as well as power system stability. A conventional distance relay can’t properly operate under transient stability conditions; therefore, it cause mol-operation, and it will adversely impact on its trip signals. To overcome this problem, the Out Of Step (OOS relay has modeled and simulated to joint with distance relay to supervise and control on its trip signals response. The setting characteristics technique of the OOS based on concentric polygons scheme method to detect power swing under transient stability situation.         This study ia a modeling and simulating using (Maltab\\ Simulink software. A Two relays had been  performed   and  tested  with  two equivalents network connected to ends.      The results of this study showed an activity and reliability of this way to control the distance relay response under a transient stability conditions and it indicated the possibility to find out faults which may occur at period of power swing

  3. STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR) DAN GROUND FAULT RELAY (GFR) PADA RECLOSER DI SALURAN PENYULANG PENEBEL

    OpenAIRE

    I Dewa Gde Agung Budhi Udiana; I G Dyana Arjana; Tjok Gede Indra Partha

    2017-01-01

    Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR) and Ground Fault Relay (GFR). The research was conducted at PT. PLN (Perse...

  4. On the Outage Performance of Full-Duplex Selective Decode-and-Forward Relaying

    KAUST Repository

    Khafagy, Mohammad Galal

    2013-02-25

    We evaluate the outage performance in a three-terminal full-duplex relay channel that adopts a selective decode-and-forward protocol, taking relay self-interference into account. Previous work focused on coverage extension scenarios where direct source-destination transmissions are neglected or considered as interference. In this work, we account for the relay self-interference, and exploit the cooperative diversity offered by the independently fading source/relay message replicas that arrive at the destination. We present an approximate, yet accurate, closed-form expression for the end-to-end outage probability that captures their joint effect. With the derived expression in hand, we propose a relay transmit power optimization scheme that only requires the relay knowledge of channel statistics. Finally, we corroborate our analysis with simulations.

  5. Whether and Where to Code in the Wireless Relay Channel

    DEFF Research Database (Denmark)

    Shi, Xiaomeng; Médard, Muriel; Roetter, Daniel Enrique Lucani

    2013-01-01

    The throughput benefits of random linear network codes have been studied extensively for wirelined and wireless erasure networks. It is often assumed that all nodes within a network perform coding operations. In energy-constrained systems, however, coding subgraphs should be chosen to control...... the number of coding nodes while maintaining throughput. In this paper, we explore the strategic use of network coding in the wireless packet erasure relay channel according to both throughput and energy metrics. In the relay channel, a single source communicates to a single sink through the aid of a half......-duplex relay. The fluid flow model is used to describe the case where both the source and the relay are coding, and Markov chain models are proposed to describe packet evolution if only the source or only the relay is coding. In addition to transmission energy, we take into account coding and reception...

  6. An Optimal Analysis in Wireless Powered Full-duplex Relaying Network

    Directory of Open Access Journals (Sweden)

    K.-T. Nguyen

    2017-04-01

    Full Text Available Wireless-powered cellular networks (WPCNs are currently being investigated to exploit the reliability and improve battery lifetime of mobile users. This paper investigates the energy harvesting structure of the full-duplex relaying networks. By using the time switching based relaying (TSR protocol and Amplify-and-Forward (AF model in delay-limited transmission scheme, we propose the closed-form expression of the outage probability and then calculate the optimal throughput. An important result can be taken obviously that the time fraction in TSR, the position of relay, the noise as well as the energy conversation impacting on the outage probability as well as the optimal throughput. By Monte Carlo simulation, the numerical results indicate an effective relaying strategy in full-duplex cooperative systems. Finally, we provide fundamental design guidelines for selecting time fraction in TSR that satisfies the requirements of a practical relaying system.

  7. Toward distributed relay selection for opportunistic amplify-and-forward transmission

    KAUST Repository

    Tourki, Kamel

    2011-05-01

    Opportunistic relaying in cooperative communication depends on careful relay selection. However the traditional centralized method used for opportunistic Amplify-and-Forward (OAF) protocols requires precise measurements of channel state information (CSI) at the destination (CSI-OAF). In this paper, we propose a distributed relay selection framework for opportunistic AF (D-OAF) cooperative communications and offer an accurate performance analysis based on exact statistics of the local signalto- noise ratios of the best relay. Furthermore, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures, and we compare our new results with their CSI-based counterparts. © 2011 IEEE.

  8. Exploring Community Radio Programming Practices to Inform ...

    African Journals Online (AJOL)

    A collective case study (multi-site) design was used to probe educational programming practices used in community radio. The paper explores how community radio station programming engages listeners in community generated education programmes that are produced through collaborative work with radio listener clubs.

  9. Crosslink Radio Occultation for the Remote Sensing of Planetary Atmospheres

    Science.gov (United States)

    Mannucci, A. J.; Ao, C. O.; Asmar, S.; Edwards, C. D.; Kahan, D. S.; Paik, M.; Pi, X.; Williamson, W.

    2015-12-01

    Radio occultation utilizing deep space telecommunication signals has been used with great success in the profiling of planetary atmospheres and ionospheres since the 1960s. A shortcoming of this technique, however, is the limited temporal and spatial sampling that it provides. We consider a different approach where radio occultation measurements are taken between two spacecraft orbiting an extra-terrestrial body. Such "crosslink" radio occultations between the Global Positioning System satellites and low-earth orbiting spacecraft have been routinely acquired to provide global observations of the Earth's atmosphere and ionosphere that are used for weather forecast, climate analysis, and space weather applications. The feasibility of applying this concept to other planets has recently been demonstrated for the first time, where crosslink occultation measurements have been acquired between the Mars Odyssey and Mars Reconnaissance Orbiter spacecraft. These measurements leverage the proximity link telecommunication payloads on each orbiter, which are nominally used to provide relay communication and navigation services to Mars landers and rovers. In this presentation, we will describe the Mars crosslink experiments and the corresponding data analysis in detail. In addition, we will discuss how the crosslink occultation concepts can be effectively applied in future space exploration missions.

  10. Use of Behavior and Influence Functions for Relay Selection in Cooperative Communications

    DEFF Research Database (Denmark)

    Craciunescu, Razvan; Mihovska, Albena Dimitrova; Prasad, Ramjee

    2015-01-01

    This paper uses a novel set of functions to model the relay selection process in a scenario of cooperative wireless communications. We define a utility function that reflects the behavior and influence that a selected relay may have on the quality of the link to be established for the forwarding...... of data. The utility function takes into account also the strategies of other players. To this end, we define a relay selection game and a supporting Nash Equilibrium (NE) algorithm for the choice of a relay during communication. The successful selection of a relay is evaluated by simulations in terms...

  11. Two-way CSI-assisted AF relaying with HPA nonlinearity

    KAUST Repository

    Qi, Jian; Aissa, Sonia; Alouiniz, Mohamed-Slim

    2015-01-01

    In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal

  12. Energy-efficient cooperative protocols for full-duplex relay channels

    KAUST Repository

    Khafagy, Mohammad Galal

    2013-12-01

    In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

  13. New results on performance analysis of opportunistic regenerative relaying

    KAUST Repository

    Tourki, Kamel

    2013-12-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the selected relay. We first derive the signal-to-noise (SNR) statistics for each hop, which are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation and end-to-end outage probability for a transmission rate R over Rayleigh fading channels. Furthermore, we evaluate the asymptotical performance and deduce the diversity order. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network architecture. © 2013 Elsevier B.V.

  14. Energy-efficient cooperative protocols for full-duplex relay channels

    KAUST Repository

    Khafagy, Mohammad Galal; Ismail, Amr; Alouini, Mohamed-Slim; Aï ssa, Sonia

    2013-01-01

    In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

  15. Information-guided transmission in decode-and-forward relaying systems: Spatial exploitation and throughput enhancement

    KAUST Repository

    Yang, Yuli

    2011-07-01

    In addressing the issue of achieving high throughput in half-duplex relay channels, we exploit a concept of information-guided transmission for the network consisting of a source node, a destination node, and multiple half-duplex relay nodes. For further benefiting from multiple relay nodes, the relay-selection patterns are defined as the arbitrary combinations of given relay nodes. By exploiting the difference among the spatial channels states, in each relay-help transmission additional information to be forwarded is mapped onto the index of the active relay-selection pattern besides the basic information mapped onto the traditional constellation, which is forwarded by the relay node(s) in the active relay-selection pattern, so as to enhance the relay throughtput. With iterative decoding, the destination node can achieve a robust detection by decoupling the signals forwarded in different ways. We investigate the proposed scheme considering "decode-and-forward" protocol and establish its achievable transmission rate. The analytical results on capacity behaviors prove the efficiency of the proposed scheme by showing that it achieves better capacity performance than the conventional scheme. © 2011 IEEE.

  16. Spatially Controlled Relay Beamforming

    Science.gov (United States)

    Kalogerias, Dionysios

    This thesis is about fusion of optimal stochastic motion control and physical layer communications. Distributed, networked communication systems, such as relay beamforming networks (e.g., Amplify & Forward (AF)), are typically designed without explicitly considering how the positions of the respective nodes might affect the quality of the communication. Optimum placement of network nodes, which could potentially improve the quality of the communication, is not typically considered. However, in most practical settings in physical layer communications, such as relay beamforming, the Channel State Information (CSI) observed by each node, per channel use, although it might be (modeled as) random, it is both spatially and temporally correlated. It is, therefore, reasonable to ask if and how the performance of the system could be improved by (predictively) controlling the positions of the network nodes (e.g., the relays), based on causal side (CSI) information, and exploitting the spatiotemporal dependencies of the wireless medium. In this work, we address this problem in the context of AF relay beamforming networks. This novel, cyber-physical system approach to relay beamforming is termed as "Spatially Controlled Relay Beamforming". First, we discuss wireless channel modeling, however, in a rigorous, Bayesian framework. Experimentally accurate and, at the same time, technically precise channel modeling is absolutely essential for designing and analyzing spatially controlled communication systems. In this work, we are interested in two distinct spatiotemporal statistical models, for describing the behavior of the log-scale magnitude of the wireless channel: 1. Stationary Gaussian Fields: In this case, the channel is assumed to evolve as a stationary, Gaussian stochastic field in continuous space and discrete time (say, for instance, time slots). Under such assumptions, spatial and temporal statistical interactions are determined by a set of time and space invariant

  17. Towards Reliable, Scalable, and Energy Efficient Cognitive Radio Systems

    KAUST Repository

    Sboui, Lokman

    2017-11-01

    The cognitive radio (CR) concept is expected to be adopted along with many technologies to meet the requirements of the next generation of wireless and mobile systems, the 5G. Consequently, it is important to determine the performance of the CR systems with respect to these requirements. In this thesis, after briefly describing the 5G requirements, we present three main directions in which we aim to enhance the CR performance. The first direction is the reliability. We study the achievable rate of a multiple-input multiple-output (MIMO) relay-assisted CR under two scenarios; an unmanned aerial vehicle (UAV) one-way relaying (OWR) and a fixed two-way relaying (TWR). We propose special linear precoding schemes that enable the secondary user (SU) to take advantage of the primary-free channel eigenmodes. We study the SU rate sensitivity to the relay power, the relay gain, the UAV altitude, the number of antennas and the line of sight availability. The second direction is the scalability. We first study a multiple access channel (MAC) with multiple SUs scenario. We propose a particular linear precoding and SUs selection scheme maximizing their sum-rate. We show that the proposed scheme provides a significant sum-rate improvement as the number of SUs increases. Secondly, we expand our scalability study to cognitive cellular networks. We propose a low-complexity algorithm for base station activation/deactivation and dynamic spectrum management maximizing the profits of primary and secondary networks subject to green constraints. We show that our proposed algorithms achieve performance close to those obtained with the exhaustive search method. The third direction is the energy efficiency (EE). We present a novel power allocation scheme based on maximizing the EE of both single-input and single-output (SISO) and MIMO systems. We solve a non-convex problem and derive explicit expressions of the corresponding optimal power. When the instantaneous channel is not available, we

  18. Using the 5 P Relay in Task Groups

    Science.gov (United States)

    Stanley, Paula Helen

    2006-01-01

    This article describes the 5 P Relay, a group exercise that can increase the effectiveness of task groups. The 5 P Relay is based on the principles and concepts of the Invitational Model, which emphasizes the importance of assessing the effectiveness or health of five aspects of an organization's environment: people, places, programs, processes,…

  19. 77 FR 1039 - Internet-Based Telecommunications Relay Service Numbering

    Science.gov (United States)

    2012-01-09

    ... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Part 64 [WC Docket No. 10-191; Report No. 2939] Internet... toll-free numbers by users of Internet- based Telecommunications Relay Services (iTRS). DATES... any rules of particular applicability. Subject: Internet-Based Telecommunications Relay Service...

  20. Secrecy Capacity of a Class of Orthogonal Relay Eavesdropper Channels

    Directory of Open Access Journals (Sweden)

    Aggarwal Vaneet

    2009-01-01

    Full Text Available The secrecy capacity of relay channels with orthogonal components is studied in the presence of an additional passive eavesdropper node. The relay and destination receive signals from the source on two orthogonal channels such that the destination also receives transmissions from the relay on its channel. The eavesdropper can overhear either one or both of the orthogonal channels. Inner and outer bounds on the secrecy capacity are developed for both the discrete memoryless and the Gaussian channel models. For the discrete memoryless case, the secrecy capacity is shown to be achieved by a partial decode-and-forward (PDF scheme when the eavesdropper can overhear only one of the two orthogonal channels. Two new outer bounds are presented for the Gaussian model using recent capacity results for a Gaussian multiantenna point-to-point channel with a multiantenna eavesdropper. The outer bounds are shown to be tight for two subclasses of channels. The first subclass is one in which the source and relay are clustered, and the eavesdropper receives signals only on the channel from the source and the relay to the destination, for which the PDF strategy is optimal. The second is a subclass in which the source does not transmit to the relay, for which a noise-forwarding strategy is optimal.

  1. Secure Communication for Two-Way Relay Networks with Imperfect CSI

    Directory of Open Access Journals (Sweden)

    Cong Sun

    2017-09-01

    Full Text Available This paper considers a two-way relay network, where two legitimate users exchange messages through several cooperative relays in the presence of an eavesdropper, and the Channel State Information (CSI of the eavesdropper is imperfectly known. The Amplify-and-Forward (AF relay protocol is used. We design the relay beamforming weights to minimize the total relay transmit power, while requiring the Signal-to-Noise-Ratio (SNRs of the legitimate users to be higher than the given thresholds and the achievable rate of the eavesdropper to be upper-bounded. Due to the imperfect CSI, a robust optimization problem is summarized. A novel iterative algorithm is proposed, where the line search technique is applied, and the feasibility is preserved during iterations. In each iteration, two Quadratically-Constrained Quadratic Programming (QCQP subproblems and a one-dimensional subproblem are optimally solved. The optimality property of the robust optimization problem is analyzed. Simulation results show that the proposed algorithm performs very close to the non-robust model with perfect CSI, in terms of the obtained relay transmit power; it~achieves higher secrecy rate compared to the existing work. Numerically, the proposed algorithm converges very quickly, and more than 85% of the problems are solved optimally.

  2. Design of Asymmetrical Relay Resonators for Maximum Efficiency of Wireless Power Transfer

    Directory of Open Access Journals (Sweden)

    Bo-Hee Choi

    2016-01-01

    Full Text Available This paper presents a new design method of asymmetrical relay resonators for maximum wireless power transfer. A new design method for relay resonators is demanded because maximum power transfer efficiency (PTE is not obtained at the resonant frequency of unit resonator. The maximum PTE for relay resonators is obtained at the different resonances of unit resonator. The optimum design of asymmetrical relay is conducted by both the optimum placement and the optimum capacitance of resonators. The optimum placement is found by scanning the positions of the relays and optimum capacitance can be found by using genetic algorithm (GA. The PTEs are enhanced when capacitance is optimally designed by GA according to the position of relays, respectively, and then maximum efficiency is obtained at the optimum placement of relays. The capacitance of the second resonator to nth resonator and the load resistance should be determined for maximum efficiency while the capacitance of the first resonator and the source resistance are obtained for the impedance matching. The simulated and measured results are in good agreement.

  3. Advanced sensing techniques for cognitive radio

    CERN Document Server

    Zhao, Guodong; Li, Shaoqian

    2017-01-01

    This SpringerBrief investigates advanced sensing techniques to detect and estimate the primary receiver for cognitive radio systems. Along with a comprehensive overview of existing spectrum sensing techniques, this brief focuses on the design of new signal processing techniques, including the region-based sensing, jamming-based probing, and relay-based probing. The proposed sensing techniques aim to detect the nearby primary receiver and estimate the cross-channel gain between the cognitive transmitter and primary receiver. The performance of the proposed algorithms is evaluated by simulations in terms of several performance parameters, including detection probability, interference probability, and estimation error. The results show that the proposed sensing techniques can effectively sense the primary receiver and improve the cognitive transmission throughput. Researchers and postgraduate students in electrical engineering will find this an exceptional resource.

  4. Relay Placement for FSO Multihop DF Systems With Link Obstacles and Infeasible Regions

    KAUST Repository

    Zhu, Bingcheng

    2015-05-19

    Optimal relay placement is studied for free-space optical multihop communication with link obstacles and infeasible regions. An optimal relay placement scheme is proposed to achieve the lowest outage probability, enable the links to bypass obstacles of various geometric shapes, and place the relay nodes in specified available regions. When the number of relay nodes is large, the searching space can grow exponentially, and thus, a grouping optimization technique is proposed to reduce the searching time. We numerically demonstrate that the grouping optimization can provide suboptimal solutions close to the optimal solutions, but the average searching time linearly grows with the number of relay nodes. Two useful theorems are presented to reveal insights into the optimal relay locations. Simulation results show that our proposed optimization framework can effectively provide desirable solution to the problem of optimal relay nodes placement. © 2015 IEEE.

  5. Semiconductor relay and its manufacture method. Handotai relay oyobi sono seizo hoho

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M

    1993-06-01

    The invention relates to a semiconductor relay in which a light emitting diode and a photovoltaic element are arranged in the opposite positions and connected with a light connection and aims to present a light transmission path to transmit input signals to the light emitting diode to the side of the photovoltaic element with a negligible light loss effectively. The invention presents a semiconductor relay, in which a light emitting diode loaded on the first lead frame and the light receiving part of the photovoltaic element to drive a MOSFET element loaded on the second lead frame and acting as a switch element are connected through an insulator tube with an opaque outer wall, and the interior of the insulator tube is filled with a transparent insulating filler, so that the invention affords a light transmission path without light leakage from the interior of the opaque insulator tube and with the stability in the form and no light loss. 3 figs.

  6. Programming A Molecular Relay for Ultrasensitive Biodetection through 129 Xe NMR

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yanfei [Department of Chemistry, University of Pennsylvania, 231 South 34th Street Philadelphia PA 19104-6323 USA; Roose, Benjamin W. [Department of Chemistry, University of Pennsylvania, 231 South 34th Street Philadelphia PA 19104-6323 USA; Philbin, John P. [Department of Chemistry, University of Pennsylvania, 231 South 34th Street Philadelphia PA 19104-6323 USA; Doman, Jordan L. [Department of Chemistry, University of Pennsylvania, 231 South 34th Street Philadelphia PA 19104-6323 USA; Dmochowski, Ivan J. [Department of Chemistry, University of Pennsylvania, 231 South 34th Street Philadelphia PA 19104-6323 USA

    2015-12-21

    We reported a supramolecular strategy for detecting specific proteins in complex media by using hyperpolarized 129Xe NMR. A cucurbit[6]uril (CB[6])-based molecular relay was programmed for three sequential equilibrium conditions by designing a two-faced guest (TFG) that initially binds CB[6] and blocks the CB[6]–Xe interaction. Moreover, the protein analyte recruits the TFG and frees CB[6] for Xe binding. TFGs containing CB[6]- and carbonic anhydrase II (CAII)-binding domains were synthesized in one or two steps. X-ray crystallography confirmed TFG binding to Zn2+ in the deep CAII active-site cleft, which precludes simultaneous CB[6] binding. The molecular relay was reprogrammed to detect avidin by using a different TFG. Finally, Xe binding by CB[6] was detected in buffer and in E. coli cultures expressing CAII through ultrasensitive 129Xe NMR spectroscopy.

  7. Environmental Assessment for Leasing Land for the Siting, Construction and Operation of a Commercial AM Radio Antenna at Los Alamos National Laboratory, Los Alamos, NM

    Energy Technology Data Exchange (ETDEWEB)

    N/A

    2000-02-16

    The United States (U.S.) Department of Energy (DOE) proposes to lease approximately 3 acres of land at the Los Alamos National Laboratory (LANL) on the southeast tip of Technical Area (TA) 54 for the siting, construction and operation of an AM radio broadcasting antenna. This Environmental Assessment (EA) has been developed in order to assess the environmental effects of the Proposed Action and No Action alternative. The Proposed Action includes the lease of land for the siting, construction and operation of an AM radio broadcasting antenna in TA-54, just north of Pajarito Road and State Highway 4. The No Action Alternative was also considered. Under the No Action Alternative, DOE would not lease land on LANL property for the siting and operation of an AM radio broadcasting antenna; the DOE would not have a local station for emergency response use; and the land would continue to be covered in native vegetation and serve as a health and safety buffer zone for TA-54 waste management activities. Other potential sites on LANL property were evaluated but dismissed for reasons such as interference with sensitive laboratory experiments. Potential visual, health, and environmental effects are anticipated to be minimal for the Proposed Action. The radio broadcasting antenna would be visible against the skyline from some public areas, but would be consistent with other man-made objects in the vicinity that partially obstruct viewsheds (e.g. meteorological tower, power lines). Therefore, the net result would be a modest change of the existing view. Electromagnetic field (EMF) emissions from the antenna would be orders or magnitude less than permissible limits. The proposed antenna construction would not affect known cultural sites, but is located in close proximity to two archaeological sites. Construction would be monitored to ensure that the associated road and utility corridor would avoid cultural sites.

  8. Novel half-coherent receivers for amplify-and-forward relaying

    KAUST Repository

    Khan, Fahd Ahmed; Chen, Yunfei; Alouini, Mohamed-Slim

    2012-01-01

    Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link

  9. Relay-aided multi-cell broadcasting with random network coding

    DEFF Research Database (Denmark)

    Lu, Lu; Sun, Fan; Xiao, Ming

    2010-01-01

    We investigate a relay-aided multi-cell broadcasting system using random network codes, where the focus is on devising efficient scheduling algorithms between relay and base stations. Two scheduling algorithms are proposed based on different feedback strategies; namely, a one-step scheduling...

  10. Mutual Information of Buffer-Aided Full-Duplex Relay Channels

    KAUST Repository

    Shafie, Ahmed El

    2017-04-09

    We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

  11. Mutual Information of Buffer-Aided Full-Duplex Relay Channels

    KAUST Repository

    Shafie, Ahmed El; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

    2017-01-01

    We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

  12. Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

    KAUST Repository

    Hussain, Syed Imtiaz; Hasna, Mazen Omar; Alouini, Mohamed-Slim

    2012-01-01

    Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

  13. Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

    KAUST Repository

    Hussain, Syed Imtiaz

    2012-09-01

    Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

  14. Characterization of the geology, geochemistry, and microbiology of the radio frequency heating demonstration site at the Savannah River Site

    International Nuclear Information System (INIS)

    Eddy Dilek, C.A.; Jarosch, T.R.; Fliermans, C.B.; Looney, B.B.; Parker, W.H.

    1993-08-01

    The overall objective of the Integrated Demonstration Project for the Remediation of Organics at Nonarid Sites at the Savannah River Site (SRS) is to evaluate innovative remediation, characterization, and monitoring systems to facilitate restoration of contaminated sites. The first phase of the demonstration focused on the application and development of in situ air stripping technologies to remediate sediments and groundwater contaminated with volatile organic compounds (VOCs). The second phase focused on the enhancement of the in situ air stripping process by adding selected nutrients to stimulate naturally occurring microorganisms that degrade VOCs. The purpose of the third phase was to evaluate the use of heating technologies [radio frequency (rf) and ohmic heating] to enhance the removal of contamination from clay layers where mass transfer is limited. The objective of this report is to document pretest and post-test data collected in support of the rf heating demonstration. The following data are discussed in this report: (1) a general description of the site including piezometers and sensors installed to monitor the remedial process; (2) stratigraphy, lithology, and a detailed geologic cross section of the study site; (3) tabulations of pretest and post-test moisture and VOC content of the sediments; (4) sampling and analysis procedures for sediment samples; (5) microbial abundance and diversity; (6) three-dimensional images of pretest and post-test contaminant distribution; (7) volumetric calculations

  15. The sequence relay selection strategy based on stochastic dynamic programming

    Science.gov (United States)

    Zhu, Rui; Chen, Xihao; Huang, Yangchao

    2017-07-01

    Relay-assisted (RA) network with relay node selection is a kind of effective method to improve the channel capacity and convergence performance. However, most of the existing researches about the relay selection did not consider the statically channel state information and the selection cost. This shortage limited the performance and application of RA network in practical scenarios. In order to overcome this drawback, a sequence relay selection strategy (SRSS) was proposed. And the performance upper bound of SRSS was also analyzed in this paper. Furthermore, in order to make SRSS more practical, a novel threshold determination algorithm based on the stochastic dynamic program (SDP) was given to work with SRSS. Numerical results are also presented to exhibit the performance of SRSS with SDP.

  16. Channel allocation and rate adaptation for relayed transmission over correlated fading channels

    KAUST Repository

    Hwang, Kyusung; Hossain, Md Jahangir; Ko, Youngchai; Alouini, Mohamed-Slim

    2009-01-01

    at both the source and relay nodes, we develop an optimal channel allocation and rate adaptation policy for a dual-hop relayed transmission. As such the overall transmit power for the relayed system is minimized while a target packet dropping rate (PDR

  17. Commercial grade item (CGI) dedication of MDR relays for nuclear safety related applications

    Science.gov (United States)

    Das, Ranjit K.; Julka, Anil; Modi, Govind

    1994-08-01

    MDR relays manufactured by Potter & Brumfield (P&B) have been used in various safety related applications in commercial nuclear power plants. These include emergency safety features (ESF) actuation systems, emergency core cooling systems (ECCS) actuation, and reactor protection systems. The MDR relays manufactured prior to May 1990 showed signs of generic failure due to corrosion and outgassing of coil varnish. P&B has made design changes to correct these problems in relays manufactured after May 1990. However, P&B does not manufacture the relays under any 10CFR50 Appendix B quality assurance (QA) program. They manufacture the relays under their commercial QA program and supply these as commercial grade items. This necessitates CGI Dedication of these relays for use in nuclear-safety-related applications. This paper presents a CGI dedication program that has been used to dedicate the MDR relays manufactured after been used to dedicate the MDR relays manufactured after May 1990. The program is in compliance with current Nuclear Regulatory Commission (NRC) and Electric Power Research Institute (EPRI) guidelines and applicable industry standards; it specifies the critical characteristics of the relays, provides the tests and analysis required to verify the critical characteristics, the acceptance criteria for the test results, performs source verification to quality P&B for its control of the critical characteristics, and provides documentation. The program provides reasonable assurance that the new MDR relays will perform their intended safety functions.

  18. Cooperative relay-based multicasting for energy and delay minimization

    KAUST Repository

    Atat, Rachad; Yaacoub, Elias E.; Alouini, Mohamed-Slim; Abu-Dayya, Adnan A.

    2012-01-01

    mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles

  19. Massive MIMO Relay Systems with Multipair Wireless Information and Power Transfer

    Directory of Open Access Journals (Sweden)

    Hongwu Liu

    2017-01-01

    Full Text Available This paper investigates destination-aided simultaneous wireless information and power transfer (SWIPT for a decode-and-forward relay network, in which massive multiple-input multiple-output antennas are deployed at relay to assist communications among multiple source-destination pairs. During relaying, energy signals are emitted from multiple destinations when multiple sources are sending their information signals to relay. With power splitting and unlimited antennas at relay, asymptotic expression of harvested energy is derived. The analysis reveals that asymptotic harvested energy is independent of fast fading effect of wireless channels; meanwhile transmission powers of each source and destination can be scaled down inversely proportional to the number of relay antennas. To significantly reduce energy leakage interference and multipair interference, zero-forcing processing and maximum-ratio combing/maximum-ratio transmission are employed at relay. Fundamental trade-off between harvested energy and achievable sum rate is quantified. It is shown that asymptotic sum rate is neither convex nor concave with respect to power splitting and destination transmission power. Thus, a one-dimensional embedded bisection algorithm is proposed to jointly determine the optimal power splitting and destination transmission power. It shows that destination-aided SWIPT are beneficial for harvesting energy and increasing sum rate. The significant sum rate improvements of the proposed schemes are verified by numerical results.

  20. Improved Relay Node Placement Algorithm for Wireless Sensor Networks Application in Wind Farm

    DEFF Research Database (Denmark)

    Chen, Qinyin; Hu, Y.; Chen, Zhe

    2013-01-01

    -tolerance. Each wind turbine has a potentially large number of data points needing to be monitored and collected, as farms continue to increase in scale; distances between turbines can reach several hundred meters. Optimal placement of relays in a large farm requires an efficient algorithmic solution. A relay...... node placement algorithm is proposed in this paper to approximate the optimal position for relays connecting each turbine. However, constraints are then required to prevent relay nodes being overloaded in 3-dimensions. The algorithm is extended to 3-dimensional Euclidean space for this optimal relay...

  1. Performance analysis of two-way amplify and forward relaying with adaptive modulation

    KAUST Repository

    Hwang, Kyusung

    2009-09-01

    In this paper, we study two-way amplify-and-forward relaying in conjunction with adaptive modulation over a multiple relay network. In order to keep the diversity order equal to the number of relays and maintain a low complexity, we consider the best relay selection scheme in this work. Based on the proposed selection criterion for the best relay, we analyze the average spectral efficiency by its approximated upper bound. In addition, we extend the proposed scheme to the case where a direct path between source and destination exists. Our numerical examples show that the proposed system offers a considerable gain in the spectral efficiency while satisfying the error rates requirements. ©2009 IEEE.

  2. 78 FR 21929 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

    Science.gov (United States)

    2013-04-12

    ... Relay Loadability Reliability Standard; Notice of Compliance Filing Take notice that on February 19... Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61,221 (2010) (Order No. 733); order..., 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138 FERC ] 61,197...

  3. 78 FR 55249 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

    Science.gov (United States)

    2013-09-10

    ...; RM11-16-000] Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing Take.... \\1\\ Transmission Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61, 221 (2010..., Order No. 733-B, 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138...

  4. PERFORMANCE ANALYSIS OF COOPERATION SCHEMES IN EAVESDROPPER ASSISTED RELAY CHANNEL

    Directory of Open Access Journals (Sweden)

    Vaibhav Kumar Gupta

    2014-06-01

    Full Text Available The prominence of the wireless communication has been urging the monotonically increasing demand of security and privacy. In wireless systems, the notion of perfect secrecy of information with respect to illegitimate nodes can be ensured via physical layer security (PLS techniques. Unfortunately, they can be made less effective if source- eavesdropper wiretap channel is better than the main source-receiver channel. The various node cooperation schemes can be employed to combat this limitation where a relay node assists the communication to improve the performance significantly. In this paper, a four node wireless communication system consisting of a source, a destination, a relay and an eavesdropper as wire-tapper has been considered. The performance of the traditional cooperation schemes in terms of secrecy rate has been investigated with a different scenario where relay node helps the eavesdropper to deteriorate the secrecy rate. In addition, since legitimate receiver can overhear the transmission of relay, it favours the achievable secrecy rate. We formulate an analytical expression of conditional secrecy outage probability for the investigated system. From the obtained simulation results, it has been observed that secrecy rate is monotonically increases with path loss index. Furthermore, the proper selection of the system parameters leads to enhance the secrecy performance of the system even if relay pertains to degrade the performance. Amplify-and-forward, cooperation, decode-and-Forward, secrecy rate, relay.

  5. Relay selection in cooperative communication systems over continuous time-varying fading channel

    Directory of Open Access Journals (Sweden)

    Ke Geng

    2017-02-01

    Full Text Available In this paper, we study relay selection under outdated channel state information (CSI in a decode-and-forward (DF cooperative system. Unlike previous researches on cooperative communication under outdated CSI, we consider that the channel varies continuously over time, i.e., the channel not only changes between relay selection and data transmission but also changes during data transmission. Thus the level of accuracy of the CSI used in relay selection degrades with data transmission. We first evaluate the packet error rate (PER of the cooperative system under continuous time-varying fading channel, and find that the PER performance deteriorates more seriously under continuous time-varying fading channel than when the channel is assumed to be constant during data transmission. Then, we propose a repeated relay selection (RRS strategy to improve the PER performance, in which the forwarded data is divided into multiple segments and relay is reselected before the transmission of each segment based on the updated CSI. Finally, we propose a combined relay selection (CRS strategy which takes advantage of three different relay selection strategies to further mitigate the impact of outdated CSI.

  6. Hybrid reed: Solid-state devices are a new generation of protective relays

    Directory of Open Access Journals (Sweden)

    Gurevich Vladimir

    2007-01-01

    Full Text Available Research and development in the field of electromechanical protective relays has not been conducted for tens of years. Author’s approach allows viewing the problem of re-equipment of relay protection in a new way. In the author’s opinion combination of reed switches with magnetic circuits and semiconductor elements opens new avenues in development of the promising protective relays featuring reliability, simplicity and low cost. Examples of protective relays made with these elements are given below.

  7. Minimax robust relay selection based on uncertain long-term CSI

    KAUST Repository

    Nisar, Muhammad Danish; Alouini, Mohamed-Slim

    2014-01-01

    Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot

  8. On full duplex Gaussian relay channels with self-interference

    KAUST Repository

    Behboodi, Arash

    2016-08-15

    Self interference (SI) in full duplex (FD) systems is the interference caused by the transmission stream on the reception stream. Being one of the main restrictive factors for performance of practical full duplex systems, however, not too much is known about its effect on the fundamental limits of relaying systems. In this work, we consider the full duplex three-node relay channel with SI where SI is modeled as an additive Gaussian noise whose variance is dependent on instantaneous input power. The classical achievable rates and upper bounds for the single three-node relay channel no longer apply due to the structure of SI. Achievable rates for Decode-and-Forward (DF) and Compress-and-Forward (CF) and upper bounds on the capacity are derived assuming Gaussian inputs and SI. The deterministic model is also introduced and its capacity is characterized. The optimal joint source-relay distributions is discussed. Numerical results are provided comparing the achievable rates and upper bound. © 2016 IEEE.

  9. Superimposed Training-Based Channel Estimation for MIMO Relay Networks

    Directory of Open Access Journals (Sweden)

    Xiaoyan Xu

    2012-01-01

    Full Text Available We introduce the superimposed training strategy into the multiple-input multiple-output (MIMO amplify-and-forward (AF one-way relay network (OWRN to perform the individual channel estimation at the destination. Through the superposition of a group of additional training vectors at the relay subject to power allocation, the separated estimates of the source-relay and relay-destination channels can be obtained directly at the destination, and the accordance with the two-hop AF strategy can be guaranteed at the same time. The closed-form Bayesian Cramér-Rao lower bound (CRLB is derived for the estimation of two sets of flat-fading MIMO channel under random channel parameters and further exploited to design the optimal training vectors. A specific suboptimal channel estimation algorithm is applied in the MIMO AF OWRN using the optimal training sequences, and the normalized mean square error performance for the estimation is provided to verify the Bayesian CRLB results.

  10. Selection combining for noncoherent decode-and-forward relay networks

    Directory of Open Access Journals (Sweden)

    Nguyen Ha

    2011-01-01

    Full Text Available Abstract This paper studies a new decode-and-forward relaying scheme for a cooperative wireless network composed of one source, K relays, and one destination and with binary frequency-shift keying modulation. A single threshold is employed to select retransmitting relays as follows: a relay retransmits to the destination if its decision variable is larger than the threshold; otherwise, it remains silent. The destination then performs selection combining for the detection of transmitted information. The average end-to-end bit-error-rate (BER is analytically determined in a closed-form expression. Based on the derived BER, the problem of choosing an optimal threshold or jointly optimal threshold and power allocation to minimize the end-to-end BER is also investigated. Both analytical and simulation results reveal that the obtained optimal threshold scheme or jointly optimal threshold and power-allocation scheme can significantly improve the BER performance compared to a previously proposed scheme.

  11. Novel half-coherent receivers for amplify-and-forward relaying

    KAUST Repository

    Khan, Fahd Ahmed

    2012-06-01

    Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link or the relay-destination link. These receivers are termed as, \\'half-coherent receivers\\' as they have channel-state-information (CSI) of only one of two links. These receivers can be very useful in a system in which only the relay can afford high complexity by having a channel estimation module and the destination is unable to support channel estimation or a system in which only the destination can afford higher complexity and includes the channel estimation module. The analytical bit-error-rate (BER) performances of the proposed receivers are derived for Rician fading. Numerical results show considerable performance gains of the new receivers, especially at low signal-to-noise ratio. © 2012 IEEE.

  12. Self-oscillations in dynamic systems a new methodology via two-relay controllers

    CERN Document Server

    Aguilar, Luis T; Fridman, Leonid; Iriarte, Rafael

    2015-01-01

    This monograph presents a simple and efficient two-relay control algorithm for generation of self-excited oscillations of a desired amplitude and frequency in dynamic systems. Developed by the authors, the two-relay controller consists of two relays switched by the feedback received from a linear or nonlinear system, and represents a new approach to the self-generation of periodic motions in underactuated mechanical systems. The first part of the book explains the design procedures for two-relay control using three different methodologies – the describing-function method, Poincaré maps, and the locus-of-a perturbed-relay-system method – and concludes with stability analysis of designed periodic oscillations. Two methods to ensure the robustness of two-relay control algorithms are explored in the second part, one based on the combination of the high-order sliding mode controller and backstepping, and the other on higher-order sliding-modes-based reconstruction of uncertainties and their compensation where...

  13. Susceptibility of modern relay protection: Will protection from cyber attacks help?

    Directory of Open Access Journals (Sweden)

    Gurevich Vladimir

    2014-01-01

    Full Text Available Modern trends in relay protection (RP based on the substitution of electromechanical protection relays (EMPR by digital protective relays (DPR have resulted in the emergence of an absolutely new problem, which was not known before. This problem is the possibility of an intentional remote destructive impact (IRDI on relay protection in order to put it out of action or make it perform functions that have nothing to do with the current operational mode of protected electric equipment. Traditional and well-known methods ensuring information safety cannot fully prevent unauthorized actions of RP. The article describes a new way for the problem solution.

  14. Radio-contaminated casualties treatment: an unusual application of technical shelters used on the Ile Longue site

    International Nuclear Information System (INIS)

    Laroche, P.; Rousset, J.; Abiliou, R.; Roe, H.; Berthelot, B.; Lemaire, L.

    2002-01-01

    While the radio-contaminated casualties treatment center (CTBRC) of the military hospital of Brest is reconstructed an unusual structure has been built on the Ile Longue site. Technical shelters (ETM) of the French military health service have been put together in order to constitute the CTBRC/ETM. This structure is adapted to the necessities of the nuclear site of Brest. First we explain the organization of the medical intervention in case of a nuclear accident; then we describe the functions of the CTBRC. People from hospital and medical teams of the nuclear oceanic French forces (FOST) take part in utilization, maintenance, training according to a particular protocol. (author)

  15. Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

    KAUST Repository

    Fareed, Muhammad Mehboob

    2014-01-06

    In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

  16. Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

    KAUST Repository

    Fareed, Muhammad Mehboob; Yang, Hong-Chuan; Alouini, Mohamed-Slim

    2014-01-01

    In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

  17. protective relay studies for the nigerian national electric 330 kv

    African Journals Online (AJOL)

    user

    1985-09-01

    Sep 1, 1985 ... protective relay schemes of the National Electric Power Authority. Some of the basic ... Nigerian special system characteristics, schemes to correct existing protection inadequacies .... relays buried in the transformer. A reach of ...

  18. Adjustable electronic load-alarm relay

    International Nuclear Information System (INIS)

    Mason, C.H.; Sitton, R.S.

    1976-01-01

    An improved electronic alarm relay for monitoring the current drawn by an ac motor or other electrical load is described. The circuit is designed to measure the load with high accuracy and to have excellent alarm repeatability. Chattering and arcing of the relay contacts are minimal. The operator can adjust the set point easily and can re-set both the high and the low alarm points by means of one simple adjustment. The relay includes means for generating a signal voltage proportional to the motor current. In a preferred form of the invention a first operational amplifier is provided to generate a first constant reference voltage which is higher than a preselected value of the signal voltage. A second operational amplifier is provided to generate a second constant reference voltage which is lower than the aforementioned preselected value of the signal voltage. A circuit comprising a first resistor serially connected to a second resistor is connected across the outputs of the first and second amplifiers, and the junction of the two resistors is connected to the inverting terminal of the second amplifier. Means are provided to compare the aforementioned signal voltage with both the first and second reference voltages and to actuate an alarm if the signal voltage is higher than the first reference voltage or lower than the second reference voltage

  19. Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

    KAUST Repository

    Benkhelifa, Fatma; Alouini, Mohamed-Slim

    2016-01-01

    In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

  20. Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

    KAUST Repository

    Benkhelifa, Fatma

    2016-01-06

    In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

  1. Enhancing overcurrent relay performance using wavelet packet transform

    International Nuclear Information System (INIS)

    Adly, A.R.

    2012-01-01

    The function of a power system relaying is to cause the prompt removal of any element of power system from service when it is subjected to short circuit or it starts to operate in any abnormal manner that might cause damage or otherwise interfere with the effective operation of the rest of the system. Overcurrent protection is one of the most widely used relays in power system which is used for both primary and back-up protective relays, and applied in every protective zone in the system. The application of time overcurrent relays in power system presents serious limitations in terms of sensitivity and selectivity. Digital forms of such relays are being mostly used which have the advantages of data recording and adaptive features. This thesis introduces a technique based on Wavelet Packet Transform (WPT) to detect short circuit faults within wide variation in generating conditions, with very small voltage variation, and High-Impedance Faults (HIFs). Besides, it examines the load current continuously and changes the relay pick up value adaptively. WPT is used to estimate proper value for the RMS fundamental and hence calculate trip time accurately even that when the signals have been contaminated with other harmonics, inter harmonics or subharmonic. Simulation work was conducted using Alternative Transient Program (ATP) package. A radial distribution system and series compensated line are modeled as case studies. The performance of the proposed overcurrent scheme for both lines is extensively tested during different operating conditions including; normal, internal short circuit faults, HIFs and similar situations to HIFs: such as capacitor switching (in), capacitor switching (out), load switching, and no load line switching. This thesis also uses a technique that estimates the location of short circuit faults on a radial distribution system. The technique was tested to evaluate its suitability. The results indicate that the proposed technique works well. It also

  2. Impact Analysis of Electrical Current Characteristics in Relay Function for Electrical and Electronic Protection

    International Nuclear Information System (INIS)

    Syirrazie Che Soh; Harzawadi Hasim

    2013-01-01

    This paper is to study effect of electrical current on relay reaction, which has coil and switch inside the relay. An analysis on the electrical current will be conducted to determine current limitation for relay activation purpose. The result of analysis showing that current characteristic of relay and applied load will present their affect to the relay function performance. Finding from this result will bring the idea to develop a suitable design circuit for electrical and electronic protection. (author)

  3. Radio Telescopes to Keep Sharp Eye on Mars Lander

    Science.gov (United States)

    2008-05-01

    As NASA's Phoenix Mars Lander descends through the Red Planet's atmosphere toward its landing on May 25, its progress will be scrutinized by radio telescopes from the National Radio Astronomy Observatory (NRAO). At NRAO control rooms in Green Bank, West Virginia, and Socorro, New Mexico, scientists, engineers and technicians will be tracking the faint signal from the lander, 171 million miles from Earth. The GBT Robert C. Byrd Green Bank Telescope CREDIT: NRAO/AUI/NSF To make a safe landing, Phoenix must make a risky descent, slowing down from nearly 13,000 mph at the top of the Martian atmosphere to only 5 mph in the final seconds before touchdown. NASA officials point out that fewer than half of all Mars landing missions have been successful, but the scientific rewards of success are worth the risk. Major events in the spacecraft's atmospheric entry, descent and landing will be marked by changes in the Doppler Shift in the frequency of the vehicle's radio signal. Doppler Shift is the change in frequency caused by relative motion between the transmitter and receiver. At Green Bank, NRAO and NASA personnel will use the giant Robert C. Byrd Green Bank Telescope (GBT) to follow the Doppler changes and verify that the descent is going as planned. The radio signal from Phoenix is designed to be received by other spacecraft in Mars orbit, then relayed to Earth. However, the GBT, a dish antenna with more than two acres of collecting surface and highly-sensitive receivers, can directly receive the transmissions from Phoenix. "We'll see the frequency change as Phoenix slows down in the Martian atmosphere, then there will be a big change when the parachute deploys," said NRAO astronomer Frank Ghigo. When the spacecraft's rocket thrusters slow it down for its final, gentle touchdown, its radio frequency will stabilize, Ghigo said. "We'll have confirmation of these major events through our direct reception several seconds earlier than the controllers at NASA's Jet Propulsion

  4. On achievable rates of interference and cognitive channels with a relay

    KAUST Repository

    Zorgui, Marwen; Rezki, Zouheir; Alouini, Mohamed-Slim

    2015-01-01

    We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

  5. On achievable rates of interference and cognitive channels with a relay

    KAUST Repository

    Zorgui, Marwen

    2015-08-30

    We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

  6. On the malfunction of disk-type induction relay under seismic condition

    International Nuclear Information System (INIS)

    Fujita, T.; Shibata, H.; Koizumi, T.

    1985-01-01

    This paper deals with the malfunction of disk-type induction relay. Equations of motion for rotational movement of induction relay was formulated and the dynamic behavior was simulated under various kind of exciting conditions. Experimental verification was also performed using two dimensional shaker table for some actual relays. Sufficient agreement was recognized between experimental and analytical results and consequently the most critical reason to cause the malfunction was pointed out. (orig.)

  7. Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

    Directory of Open Access Journals (Sweden)

    Y. Damchi

    2015-09-01

    Full Text Available Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs. Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determined based on a main network topology which may result in mis-coordination of relays when changes occur in the network topology. In the proposed method, in order to have a robust coordination, network topology changes are taken into account in the coordination problem. In the new formulation, coordination constraints for different network topologies are added to those of the main topology. A complex nonlinear optimization problem is derived to find the desirable relay settings. Then, the problem is solved using hybridized genetic algorithm (GA with linear programming (LP method (HGA. The proposed method is evaluated using the IEEE 14-bus test system. According to the results, a feasible and robust solution is obtained for D&DOCRs coordination while all constraints, which are due to different network topologies, are satisfied.

  8. Transmission Power Adaption for Full-Duplex Relay-Aided Device-to-Device Communication

    Directory of Open Access Journals (Sweden)

    Hui Dun

    2017-03-01

    Full Text Available Device-to-device (D2D communications bring significant improvements of spectral efficiency by underlaying cellular networks. However, they also lead to a more deteriorative interference environment for cellular users, especially the users in severely deep fading or shadowing. In this paper, we investigate a relay-based communication scheme in cellular systems, where the D2D communications are exploited to aid the cellular downlink transmissions by acting as relay nodes with underlaying cellular networks. We modeled two-antenna infrastructure relays employed for D2D relay. The D2D transmitter is able to transmit and receive signals simultaneously over the same frequency band. Then we proposed an efficient power allocation algorithm for the base station (BS and D2D relay to reduce the loopback interference which is inherent due to the two-antenna infrastructure in full-duplex (FD mode. We derived the optimal power allocation problem in closed form under the independent power constraint. Simulation results show that the algorithm reduces the power consumption of D2D relay to the greatest extent and also guarantees cellular users’ minimum transmit rate. Moreover, it also outperforms the existing half-duplex (HD relay mode in terms of achievable rate of D2D.

  9. Low-Complexity Combining Schemes in Dual-Hop AF Relaying Systems

    KAUST Repository

    Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

    2011-01-01

    This paper investigates the performance of different low-complexity combining schemes in the context of dual-hop amplify-and-forward (AF) relaying networks. It is assumed that the relay uses single transmit (receive) antenna due to space limitation

  10. IE Information Notice No. 85-82: Diesel generator differential protection relay not seismically qualified

    International Nuclear Information System (INIS)

    Jordan, E.L.

    1992-01-01

    Licensees of BWR and PWR nuclear generating stations have reported using a high-speed differential protection relay that has been declared by the manufacturer to be not seismically qualified for the service intended. The relay, GE Model 12CFD, which is being used for emergency diesel generator protection against electrical shorts and grounds at the generator output, has not been seismically qualified to operate in the de-energized state for this application. Generally, the relay operates in the de-energized position before EDG operation. However, it then operates in the energized position whenever the EDG provides an electrical output to essential Class IE components. The safety concern of this issue involves an inadvertent activation of the normally de-energized relay from a seismic event. Momentary activation of the relay, in the circuits examined, blocks the automatic start feature of the EDG during certain emergency plant conditions through operation of another relay in the system. The NRC review of the problems concluded that the relays should be seismically qualified in their energized and de-energized states to preclude their spurious activation during a seismic event. Additionally, review of GE's GER 3069 report, ''Relay Protection of Class IE Systems,'' shows that the 12CFD differential relays were successfully tested for 3.5 g in the energized modes and only 0.75 g in the de-energized mode. Review of GE's GER 3069 report also revealed that GE type IJD differential relays do meet seismic requirements in all modes of operation mentioned above and is the GE recommendation for replacement of the differential relay in question

  11. Implementing Strategic Planning Capabilities Within the Mars Relay Operations Service

    Science.gov (United States)

    Hy, Franklin; Gladden, Roy; Allard, Dan; Wallick, Michael

    2011-01-01

    Since the Mars Exploration Rovers (MER), Spirit and Opportunity, began their travels across the Martian surface in January of 2004, orbiting spacecraft such as the Mars 2001 Odyssey orbiter have relayed the majority of their collected scientific and operational data to and from Earth. From the beginning of those missions, it was evident that using orbiters to relay data to and from the surface of Mars was a vastly more efficient communications strategy in terms of power consumption and bandwidth compared to direct-to-Earth means. However, the coordination between the various spacecraft, which are largely managed independently and on differing commanding timelines, has always proven to be a challenge. Until recently, the ground operators of all these spacecraft have coordinated the movement of data through this network using a collection of ad hoc human interfaces and various, independent software tools. The Mars Relay Operations Service (MaROS) has been developed to manage the evolving needs of the Mars relay network, and specifically to standardize and integrate the relay planning and coordination data into a centralized infrastructure. This paper explores the journey of developing the MaROS system, from inception to delivery and acceptance by the Mars mission users.

  12. Outage Probability Analysis in Power-Beacon Assisted Energy Harvesting Cognitive Relay Wireless Networks

    Directory of Open Access Journals (Sweden)

    Ngoc Phuc Le

    2017-01-01

    Full Text Available We study the performance of the secondary relay system in a power-beacon (PB assisted energy harvesting cognitive relay wireless network. In our system model, a secondary source node and a relay node first harvest energy from distributed PBs. Then, the source node transmits its data to the destination node with the help of the relay node. Also, fading coefficients of the links from the PBs to the source node and relay node are assumed independent but not necessarily identically distributed (i.n.i.d Nakagami-m random variables. We derive exact expressions for the power outage probability and the channel outage probability. Based on that, we analyze the total outage probability of the secondary relay system. Asymptotic analysis is also performed, which provides insights into the system behavior. Moreover, we evaluate impacts of the primary network on the performance of the secondary network with respect to the tolerant interference threshold at the primary receiver as well as the interference introduced by the primary transmitter at the secondary source and relay nodes. Simulation results are provided to validate the analysis.

  13. Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

    KAUST Repository

    El Shafie, Ahmed

    2017-10-18

    We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

  14. Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

    KAUST Repository

    El Shafie, Ahmed; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

    2017-01-01

    We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

  15. Simultaneous Wireless Information and Power Transfer Mechanism in Interference Alignment Relay Networks

    Directory of Open Access Journals (Sweden)

    Fahui Wu

    2016-01-01

    Full Text Available This paper considers a simultaneous wireless information and power transfer (SWIPT mechanism in an interference alignment (IA relay system, in which source nodes send wireless information and energy simultaneously to relay nodes, and relay nodes forward the received signal to destination nodes powered by harvested energy. To manage interference and utilize interference as energy source, two-SWIPT receiver is designed, namely, power splitting (PS, and antennas switching (AS has been considered for relay system. The performance of AS- and PS-based IA relay systems is considered, as is a new energy cooperation (ECop scheme that is proposed to improve system performance. Numerical results are provided to evaluate the performance of all schemes and it is shown from the simulations that the performance of proposed ECop outperformed both AS and PS.

  16. Rate regions for coordination of Decode-and-Forward relays and direct users

    DEFF Research Database (Denmark)

    Thai, Chan; Popovski, Petar

    2012-01-01

    Recently, the ideas of wireless network coding (NC) has significantly enriched the area of wireless cooperation/relaying. They bring substantial gains in spectral efficiency mainly in scenarios with two–way relaying. Inspired by the ideas of wireless NC, recently we have proposed techniques...... for coordinated direct/relay (CDR) transmissions. Leveraging on the fact that the interference can be subsequently canceled, these techniques embrace the interference among the communication flows to/from direct and relayed users. Hence, by allowing simultaneous transmissions, spectral efficiency is increased....... In our prior work, we have proposed CDR with Decode–and–Forward (DF) relay in two scenarios. In this paper, we extend the two existing regenerative CDR schemes and proposed for the other two scenarios such that all schemes benefit from the aforementioned principle of containing the interference...

  17. Multistability and hidden attractors in a relay system with hysteresis

    DEFF Research Database (Denmark)

    Zhusubaliyev, Zhanybai T.; Mosekilde, Erik; Rubanov, Vasily G.

    2015-01-01

    with the neighborhood of that cycle. We show how the equilibrium point of a relay system disappears in a boundary-equilibrium bifurcation as the system enters the region of autonomous switching dynamics and demonstrate experimentally how a relay system can exhibit large amplitude chaotic oscillations at high values...... of the supply voltage. By investigating a four-dimensional model of the experimental relay system we finally show how a variety of hidden periodic, quasiperiodic and chaotic attractors arise, transform and disappear through different bifurcations. (C) 2015 Elsevier B.V. All rights reserved....

  18. Synthesis of relay control systems for nuclear reactors

    International Nuclear Information System (INIS)

    Postnikov, N.S.

    1996-01-01

    The problem on stabilizing an oscillatory-unstable reactor by a single-link relay system, the characteristics whereof have a dead zone and hysteresis loop, is considered. The methodology of synthesis of feedback law, providing for stochastic steady-state mode of reactor operation with the minimum frequency of control impact introduction is proposed. This methodology is applicable to general-type relay systems with arbitrary oscillatory-unstable objects. 6 refs., 5 figs

  19. Chiral relay: a novel strategy for the control and amplification of enantioselectivity in chiral Lewis acid promoted reactions.

    Science.gov (United States)

    Corminboeuf, Olivier; Quaranta, Laura; Renaud, Philippe; Liu, Mei; Jasperse, Craig P; Sibi, Mukund P

    2003-01-03

    Chiral Lewis acid catalysis has emerged as one of the premiere method to control stereochemistry. Much effort has gone into the design of superior ligands with increasing steric extension to shield distant reactive sites. We report here an alternative and complementary approach based on a "chiral relay". This strategy focuses on the improved design of achiral templates which may relay and amplify the stereochemistry from ligands. The essence of this strategy is that the chiral Lewis acid would effectively convert an achiral template into a chiral non-racemic template. This approach combines the advantages of enantioselective catalysis (substoichiometric amount of the chiral inducer) with the ones of chiral auxiliary control (efficient and predictable stereocontrol).

  20. Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

    KAUST Repository

    Benkhelifa, Fatma; Alouini, Mohamed-Slim

    2016-01-01

    relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal

  1. Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

    KAUST Repository

    Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

    2011-01-01

    In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help

  2. Uplink Capacity of 802.16j Mobile Multihop Relay Networks with Transparent Relays

    DEFF Research Database (Denmark)

    Wang, Hua; Andrews, Jeffrey G.; Iversen, Villy Bæk

    2009-01-01

    -to-end spectral efficiency. Furthermore, the position and the number of relay stations (RSs) have a great impact on the capacity gain. These results are further verified in the evaluation of the system Erlang capacity. The study demonstrates that with proper deployment of RSs and use of MIMO transmission...

  3. Relay Coordination in the Protection of Radially-Connected Power ...

    African Journals Online (AJOL)

    Protective relays detect intolerable or unwanted conditions within an assigned area, and then trip or open one or more circuit breakers to isolate the problem area before it can damage or otherwise interfere with the eective operation of the rest of the power system. It often happens that a substation feeder relay and ...

  4. Trajectory Options for a Potential Mars Mission Combining Orbiting Science, Relay and a Sample Return Rendezvous Demonstration

    Science.gov (United States)

    Guinn, Joseph R.; Kerridge, Stuart J.; Wilson, Roby S.

    2012-01-01

    Mars sample return is a major scientific goal of the 2011 US National Research Council Decadal Survey for Planetary Science. Toward achievement of this goal, recent architecture studies have focused on several mission concept options for the 2018/2020 Mars launch opportunities. Mars orbiters play multiple roles in these architectures such as: relay, landing site identification/selection/certification, collection of on-going or new measurements to fill knowledge gaps, and in-orbit collection and transportation of samples from Mars to Earth. This paper reviews orbiter concepts that combine these roles and describes a novel family of relay orbits optimized for surface operations support. Additionally, these roles provide an intersection of objectives for long term NASA science, human exploration, technology development and international collaboration.

  5. Social-Aware Relay Selection for Cooperative Multicast Device-to-Device Communications

    Directory of Open Access Journals (Sweden)

    Francesco Chiti

    2017-12-01

    Full Text Available The increasing use of social networks such as Facebook, Twitter, and Instagram to share photos, video streaming, and music among friends has generated a huge increase in the amount of data traffic over wireless networks. This social behavior has triggered new communication paradigms such as device-to-device (D2D and relaying communication schemes, which are both considered as strong drivers for the next fifth-generation (5G cellular systems. Recently, the social-aware layer and its relationship to and influence on the physical communications layer have gained great attention as emerging focus points. We focus here on the case of relaying communications to pursue the multicast data dissemination to a group of users forming a social community through a relay node, according to the extension of the D2D mode to the case of device-to-many devices. Moreover, in our case, the source selects the device to act as the relay among different users of the multicast group by taking into account both the propagation link conditions and the relay social-trust level with the constraint of minimizing the end-to-end content delivery delay. An optimization procedure is also proposed in order to achieve the best performance. Finally, numerical results are provided to highlight the advantages of considering the impact of social level on the end-to-end delivery delay in the integrated social–physical network in comparison with the classical relay-assisted multicast communications for which the relay social-trust level is not considered.

  6. Counterfactual quantum cryptography network with untrusted relay

    Science.gov (United States)

    Chen, Yuanyuan; Gu, Xuemei; Jiang, Dong; Xie, Ling; Chen, Lijun

    2015-07-01

    Counterfactual quantum cryptography allows two remote parties to share a secret key even though a physical particle is not in fact transmitted through the quantum channel. In order to extend the scope of counterfactual quantum cryptography, we use an untrusted relay to construct a multi-user network. The implementation issues are discussed to show that the scheme can be realized with current technologies. We also prove the practical security advantages of the scheme by eliminating the probability that an eavesdropper can directly access the signal or an untrusted relay can perform false operations.

  7. Generator for X-ray diagnostics with mAs-relay

    International Nuclear Information System (INIS)

    Franke, K.

    1978-01-01

    The invention concerns a generator for X-ray diagnostics with mAs-relay, which is provided with organ keys for organ-programmed selection of mAs-products. For individual setting of the recording time the mAs-relay input is connected to an auxiliary source of current supplying a constant auxiliary current. The response barrier of the mAs-relay is thereby set by time set average. For overload protection may be used a power circuit which at exceeding the programmed times, e.g. the times provided for tomography operation, reduces the X-ray tube power step by step to allowed values by means of the X-ray tube current. (orig.) [de

  8. Throughput maximization for buffer-aided hybrid half-/full-duplex relaying with self-interference

    KAUST Repository

    Khafagy, Mohammad Galal

    2015-06-01

    In this work, we consider a two-hop cooperative setting where a source communicates with a destination through an intermediate relay node with a buffer. Unlike the existing body of work on buffer-aided half-duplex relaying, we consider a hybrid half-/full-duplex relaying scenario with loopback interference in the full-duplex mode. Depending on the channel outage and buffer states that are assumed available at the transmitters, the source and relay may either transmit simultaneously or revert to orthogonal transmission. Specifically, a joint source/relay scheduling and relaying mode selection mechanism is proposed to maximize the end-to-end throughput. The throughput maximization problem is converted to a linear program where the exact global optimal solution is efficiently obtained via standard convex/linear numerical optimization tools. Finally, the theoretical findings are corroborated with event-based simulations to provide the necessary performance validation.

  9. Outage Probability versus Fairness Trade-off in Opportunistic Relay Selection with Outdated CSI

    Directory of Open Access Journals (Sweden)

    Vicario JoseLopez

    2009-01-01

    Full Text Available We analyze the existing trade-offs in terms of system performance versus fairness of a cooperative system based on opportunistic relay selection (ORS and with outdated channel state information (CSI. In particular, system performance is analytically evaluated in terms of outage probability, and the fairness behavior is assessed based on the power consumption at the different relays. In order to improve the fairness behavior of ORS while keeping the selection diversity gain, we propose a relay selection mechanism where the relay with the highest normalized signal-to-noise ratio (SNR is selected for relaying the source's information. The proposed strategy is compared with existing relay selection strategies by adopting a novel graphical representation inspired by expected profit versus risk plots used in modern portfolio theory. As shown in the paper, this strategy allows operating the system in more favorable points of the outage versus fairness region.

  10. PPM-based relay communication schemes for wireless body area networks

    NARCIS (Netherlands)

    Zhang, P.; Willems, F.M.J.; Huang, Li

    2012-01-01

    This paper investigates cooperative communication schemes based on a single relay with pulse-position modulation (PPM) signaling, for enhancing energy efficiency of wireless body area networks (WBANs) in noncoherent channel settings. We explore cooperation between the source and the relay such that

  11. Protective Relay Studies for the Nigerian National Electric 330 KV ...

    African Journals Online (AJOL)

    The fundamental reasons for requiring these specific protective relaying features are also reviewed. Other protective relaying schemes that can accomplish the same basic protection objectives are presented. Based on the Nigerian special system characteristics, schemes to correct existing protection inadequacies are ...

  12. On the benefits of location-based relay selection in mobile wireless networks

    DEFF Research Database (Denmark)

    Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

    2016-01-01

    We consider infrastructure-based mobile networks that are assisted by a single relay transmission where both the downstream destination and relay nodes are mobile. Selecting the optimal transmission path for a destination node requires up-to-date link quality estimates of all relevant links....... If the relay selection is based on link quality measurements, the number of links to update grows quadratically with the number of nodes, and measurements need to be updated frequently when nodes are mobile. In this paper, we consider a location-based relay selection scheme where link qualities are estimated...... from node positions; in the scenario of a node-based location system such as GPS, the location-based approach reduces signaling overhead, which in this case only grows linearly with the number of nodes. This paper studies these two relay selection approaches and investigates how they are affected...

  13. An automated thermoelectric power apparatus using electro-optic relays

    International Nuclear Information System (INIS)

    Chakravarti, A.; Ranganathan, R.

    1992-01-01

    We report the design and construction of a thermoelectric power apparatus using home-made electro-optic relays with Z-80A microprocessor for automatic data acquisition and control. The advantages of such relays made out of LED-LDR combinations for the measurement of ΔE and ΔT are discussed in details. (author). 7 refs., 5 figs

  14. Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

    KAUST Repository

    Benkhelifa, Fatma

    2016-03-28

    © 2015 IEEE. In this paper, we investigate two-hop Multiple- Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with simultaneous wireless information and power transfer (SWIPT) at the multi-antenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. This scheme provides an outer bound for the achievable R-E region since practical energy harvesting circuits are not yet able to harvest the energy and decode the information simultaneously. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) proposed in [1] and which separate the EH and ID transfer over the power domain and the time domain, respectively. In our study, we derive the boundary of the achievable R- E region and we show the effect of the source transmit power, the relay transmit power and the position of the relay between the source and the destination on the achievable R-E region for the ideal scenario and the two practical schemes.

  15. Alternate MIMO AF relaying networks with interference alignment: Spectral efficient protocol and linear filter design

    KAUST Repository

    Park, Kihong

    2013-02-01

    In this paper, we study a two-hop relaying network consisting of one source, one destination, and three amplify-and-forward (AF) relays with multiple antennas. To compensate for the capacity prelog factor loss of 1/2$ due to the half-duplex relaying, alternate transmission is performed among three relays, and the inter-relay interference due to the alternate relaying is aligned to make additional degrees of freedom. In addition, suboptimal linear filter designs at the nodes are proposed to maximize the achievable sum rate for different fading scenarios when the destination utilizes a minimum mean-square error filter. © 1967-2012 IEEE.

  16. Line Differential Protection Scheme Modelling for Underground 420 kV Cable Systems, EMTDC/PSCAD Relays Modelling

    DEFF Research Database (Denmark)

    Bak, Claus Leth; Sztykiel, Michal; Dollerup, Sebastian

    2011-01-01

    Based on the analysis of a specific relay model and an HVAC (High Voltage Alternating Current) cable system, a new approach to EMTDC/PSCAD modelling of protective relays is presented. Such approach allows creating complex and accurate relay models derived from the original algorithms. Relay models...... can be applied with various systems, allowing obtaining the most optimal configuration of the protective relaying. The present paper describes modelling methodology on the basis of Siemens SIPROTEC 4 7SD522/610. Relay model was verified experimentally with its real equivalent by both EMTP......-simulated and real world generated current signals connected to the relay....

  17. Half-Duplex and Full-Duplex AF and DF Relaying with Energy-Harvesting in Log-Normal Fading

    KAUST Repository

    Rabie, Khaled M.

    2017-08-15

    Energy-harvesting (EH) and wireless power transfer in cooperative relaying networks have recently attracted a considerable amount of research attention. Most of the existing work on this topic however focuses on Rayleigh fading channels, which represent outdoor environments. In contrast, this paper is dedicated to analyze the performance of dual-hop relaying systems with EH over indoor channels characterized by log-normal fading. Both half-duplex (HD) and full-duplex (FD) relaying mechanisms are studied in this work with decode-and-forward (DF) and amplify-and-forward (AF) relaying protocols. In addition, three EH schemes are investigated, namely, time switching relaying, power splitting relaying and ideal relaying receiver which serves as a lower bound. The system performance is evaluated in terms of the ergodic outage probability for which we derive accurate analytical expressions. Monte Carlo simulations are provided throughout to validate the accuracy of our analysis. Results reveal that, in both HD and FD scenarios, AF relaying performs only slightly worse than DF relaying which can make the former a more efficient solution when the processing energy cost at the DF relay is taken into account. It is also shown that FD relaying systems can generally outperform HD relaying schemes as long as the loop-back interference in FD is relatively small. Furthermore, increasing the variance of the log-normal channel has shown to deteriorate the performance in all the relaying and EH protocols considered.

  18. Cache Aided Decode-and-Forward Relaying Networks: From the Spatial View

    Directory of Open Access Journals (Sweden)

    Junjuan Xia

    2018-01-01

    Full Text Available We investigate cache technique from the spatial view and study its impact on the relaying networks. In particular, we consider a dual-hop relaying network, where decode-and-forward (DF relays can assist the data transmission from the source to the destination. In addition to the traditional dual-hop relaying, we also consider the cache from the spatial view, where the source can prestore the data among the memories of the nodes around the destination. For the DF relaying networks without and with cache, we study the system performance by deriving the analytical expressions of outage probability and symbol error rate (SER. We also derive the asymptotic outage probability and SER in the high regime of transmit power, from which we find the system diversity order can be rapidly increased by using cache and the system performance can be significantly improved. Simulation and numerical results are demonstrated to verify the proposed studies and find that the system power resources can be efficiently saved by using cache technique.

  19. Diversity-Multiplexing Trade-off for Coordinated Direct and Relay Schemes

    DEFF Research Database (Denmark)

    Thai, Chan; Popovski, Petar; De Carvalho, Elisabeth

    2013-01-01

    The recent years have brought a significant body of research on wireless Two-Way Relaying (TWR), where the use of network coding brings an evident advantage in terms of data rates. Yet, TWR scenarios represent only a special case and it is of interest to devise similar techniques in more general...... Direct/Relay (CDR) schemes, which involve two flows, of a direct and a relayed user. In this paper we characterize a CDR scheme by deriving/bounding the Diversity-Multiplexing Trade-off (DMT) function. Two cases are considered. In the first case a transmitter knows the Channel State Information (CSI...

  20. NRC Information No. 88-98: Electrical relay degradation caused by oxidation of contact surfaces

    International Nuclear Information System (INIS)

    Rossi, C.E.

    1992-01-01

    The NRC staff was recently informed by Clinton Power Station that a reactor scram on June 24, 1988, was caused by an electrical relay failure from oxide buildup on relay contact surfaces. Other information on relay failure from contact oxidation indicates that this problem may be more prevalent than previously thought. For example, a July 17, 1988, 10 CFR Part 21 report from Palo Verde, Unit 2, reported relay failures from contact oxidation that were due to the low current application of the relays. The relay contact surfaces in both of these examples are silver-nickel alloys, and both applications were for low current (i.e., milli-ampere current). Electrical relay contacts made of silver-nickel or silver-cadmium alloys will oxidize (tarnish) when used in low current applications because of the absence of contact surface sparking from the typical relay contact ''making and breaking'' functions. The sparking in the contact surfaces promotes a self-cleaning mechanism that reduces the tarnish buildup on the silver-nickel or silver-cadmium contacts. Discussions with one relay manufacturer revealed that the normal industry practice for low current circuit applications is either to use a contact surface material that will not oxidize or to compensate for the oxidation by increased maintenance activities to ensure reliability. The applied voltage may also influence contact oxidation

  1. Simulation of Distance Relay for Load Encroachment Alleviation with Agent Based Supervision of Zone3

    Directory of Open Access Journals (Sweden)

    Mohamed Badr

    2017-03-01

    Full Text Available Cascaded tripping of power lines due to mal-operation of zone-3 distance relays has been one of the main causes of many previous blackouts worldwide. Encroachment of load into zone-3 characteristics during stressed system operation conditions is a basic factor for such mal-operation of the relays. By improving the operation of zone-3, it is possible to prevent mal-operations so that cascaded line tripping can be avoided. For proper study of the behavior of distance relay during faults and load encroachment phenomenon, we must build a model of distance relay, so in this paper a modeling study of distance relay is implemented using MATLAB/Simulink program. However, this model is distinguished from previous models that, examines in detail the third zone of distance relay. Many cases are simulated with changing line loading and fault location to ensure the capability of the relay to detect the fault and thus the maximum load ability limit of distance relay is obtained. In order to prevent cascading events caused by hidden failures in zone-3 relays, agent based relay architectures have been suggested in the recent past. In such architectures each zone-3 relay contains agents that require communication with other agents at various relevant relays in order to distinguish a real zone-3 event from a temporary overload. In this paper, a local master agent is consulted by all zone-3 agents before a tripping decision is made. The master agent maintains a rule base which is updated based on the local topology of the network and real time monitoring of the status of other relays and circuit breakers. Cisco Packet Tracer program is used for running communication network simulations. The result of the simulation indicate that the time estimated to send and receive a packet data unit (PDU message between one relay to anther can satisfy the communication requirement for the proposed scheme with fiber media.

  2. On Amplify-and-Forward Relaying Over Hyper-Rayleigh Fading Channels

    Directory of Open Access Journals (Sweden)

    S. H. Alvi

    2014-12-01

    Full Text Available Relayed transmission holds promise for the next generation of wireless communication systems due to the performance gains it can provide over non-cooperative systems. Recently hyper-Rayleigh fading, which represents fading conditions more severe than Rayleigh fading, has received attention in the context of many practical communication scenarios. Though power allocation for Amplify-and-Forward (AF relaying networks has been studied in the literature, a theoretical analysis of the power allocation problem for hyper-Rayleigh fading channels is a novel contribution of this work. We develop an optimal power allocation (OPA strategy for a dual-hop AF relaying network in which the relay-destination link experiences hyper-Rayleigh fading. A new closed-form expression for the average signal-to-noise ratio (SNR at destination is derived and it is shown to provide a new upper-bound on the average SNR at destination, which outperforms a previously proposed upper-bound based on the well-known harmonic-geometric mean inequality. An OPA across the source and relay nodes, subject to a sum-power constraint, is proposed and it is shown to provide measurable performance gains in average SNR and SNR outage at the destination relative to the case of equal power allocation.

  3. Partial relay selection based on shadowing side information over generalized composite fading channels

    KAUST Repository

    Yilmaz, Ferkan

    2011-11-01

    In this paper, in contrast to the relay selection protocols available in the literature, we propose a partial relay selection protocol utilizing only the shadowing side information of the relays instead of their full channel side information in order to select a relay in a dual-hop relaying system through the available limited feedback channels and power budget. We then presented an exact unified performance expression combining the average bit error probability, ergodic capacity, and moments-generating function of the proposed partial relay selection over generalized fading channels. Referring to the unified performance expression introduced in [1], we explicitly offer a generic unified performance expression that can be easily calculated and that is applicable to a wide variety of fading scenarios. Finally, as an illustration of the mathematical formalism, some numerical and simulation results are generated for an extended generalized-K fading environment, and these numerical and simulation results are shown to be in perfect agreement. © 2011 IEEE.

  4. A study of optimization problem for amplify-and-forward relaying over weibull fading channels

    KAUST Repository

    Ikki, Salama Said; Aissa, Sonia

    2010-01-01

    This paper addresses the power allocation and relay positioning problems in amplify-and-forward cooperative networks operating in Weibull fading environments. We study adaptive power allocation (PA) with fixed relay location, optimal relay location

  5. Relays undergo seismic tests

    International Nuclear Information System (INIS)

    Burton, J.C.

    1977-01-01

    Utilities are required by the Nuclear Regulatory Commission to document that seismic vibration will not adversely affect critical electrical equipment. Seismic testing should be designed to determine the malfunction level (fragility testing). Input possibilities include a continuous sine, a decaying sine, a sine beat, random vibrations, and combinations of random vibrations and sine beat. The sine beat most accurately simulates a seismic event. Test frequencies have a broad range in order to accommodate a variety of relay types and cabinet mounting. Simulation of motion along three axes offers several options, but is best achieved by three in-phase single-axis vibration machines that are less likely to induce testing fatigue failure. Consensus on what constitutes relay failure favors a maximum two microsecond discontinuity. Performance tests should be conducted for at least two of the following: (1) nonoperating modes, (2) operating modes, or (3) the transition above the two modes, with the monitoring mode documented for all three. Results should specify a capability curve of maximum safe seismic acceleration and a graph plotting acceleration with sine-beat frequency

  6. Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

    KAUST Repository

    Fareed, Muhammad Mehboob; Uysal, Murat; Tsiftsis, Theodoros A.

    2014-01-01

    In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

  7. Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

    KAUST Repository

    Fareed, Muhammad Mehboob

    2014-06-01

    In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

  8. Three-dimensional modeling of subsurface contamination: A case study from the radio frequency-heating demonstration at the Savannah River Site

    International Nuclear Information System (INIS)

    Poppy, S.P.; Eddy-Dilek, C.A.; Jarosch, T.R.

    1994-01-01

    Computer based three-dimensional modeling is a powerful tool used for visualizing and interpreting environmental data collected at the Savannah River Site (SRS). Three-dimensional modeling was used to image and interpret subsurface spatial data, primarily, changes in the movement, the accumulation, and the depletion of contaminants at the Integrated Demonstration Site (IDS), a proving ground for experimental environmental remediation technologies. Three-dimensional models are also educational tools, relaying complex environmental data to interested non-technical individuals who may be unfamiliar with the concepts and terminology involved in environmental studies. The public can draw their own conclusions of the success of the experiments after viewing the three-dimensional images set up in a chronological order. The three-dimensional grids generated during these studies can also be used to create images for visualization and animated sequences that model contamination movement. Animation puts the images of contamination distribution in motion and results in a new perspective on the effects of the remedial demonstration

  9. Accurate performance analysis of opportunistic decode-and-forward relaying

    KAUST Repository

    Tourki, Kamel

    2011-07-01

    In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be considered unusable, and the destination may use a selection combining technique. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end outage probability for a transmission rate R. Furthermore, we evaluate the asymptotical performance analysis and the diversity order is deduced. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures. © 2011 IEEE.

  10. Reliability Analysis of Differential Relay as Main Protection Transformer Using Fuzzy Logic Algorithm

    Science.gov (United States)

    Mulyadi, Y.; Sucita, T.; Sumarto; Alpani, M.

    2018-02-01

    Electricity supply demand is increasing every year. It makes PT. PLN (Persero) is required to provide optimal customer service and satisfaction. Optimal service depends on the performance of the equipment of the power system owned, especially the transformer. Power transformer is an electrical equipment that transforms electricity from high voltage to low voltage or vice versa. However, in the electrical power system, is inseparable from interference included in the transformer. But, the disturbance can be minimized by the protection system. The main protection transformer is differential relays. Differential relays working system using Kirchoff law where inflows equal outflows. If there are excessive currents that interfere then the relays will work. But, the relay can also experience decreased performance. Therefore, this final project aims to analyze the reliability of the differential relay on the transformer in three different substations. Referring to the standard applied by the transmission line protection officer, the differential relay shall have slope characteristics of 30% in the first slope and 80% in the second slope when using two slopes and 80% when using one slope with an instant time and the corresponding ratio. So, the results obtained on the Siemens differential release have a reliable slope characteristic with a value of 30 on the fuzzy logic system. In a while, ABB a differential relay is only 80% reliable because two experiments are not reliable. For the time, all the differential relays are instant with a value of 0.06 on the fuzzy logic system. For ratios, the differential relays ABB have a better value than others brand with a value of 151 on the fuzzy logic system.

  11. Tests of microprocessor-based relay protection devices: Problems and solutions

    Directory of Open Access Journals (Sweden)

    Gurevich Vladimir

    2009-01-01

    Full Text Available Usually, the operational condition of relay protection devices is checked with specific settings used for the relay operation in a certain network point. In the author's opinion in order to verify the proper operation of complex multifunctional microprocessor-based protection devices (MPD at their inspection, start-up after repairs or during periodic tests there is no need to use the actual settings at which the relay is to be operated in a certain network's point. It should be tested for proper operation at several of its most critical preset characteristic points as well as in several preset characteristics constituting its most complicated (combined operation modes, including the dynamic operation modes with preset transition processes specific for standard power networks (not necessarily for a specific point. The proposed set of actions for the unification of software platforms of the modern, microprocessor-based relay protection test systems will enable examination of modern MPD in an absolutely new way. .

  12. Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

    KAUST Repository

    Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

    2011-01-01

    In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

  13. Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

    KAUST Repository

    Tourki, Kamel

    2010-10-01

    In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

  14. Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

    KAUST Repository

    Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

    2010-01-01

    In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

  15. Location-quality-aware policy optimisation for relay selection in mobile networks

    DEFF Research Database (Denmark)

    Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

    2016-01-01

    for resulting performance of such network optimizations. In mobile scenarios, the required information collection and forwarding causes delays that will additionally affect the reliability of the collected information and hence will influence the performance of the relay selection method. This paper analyzes...... the joint influence of these two factors in the decision process for the example of a mobile location-based relay selection approach using a continuous time Markov chain model. Efficient algorithms are developed based on this model to obtain optimal relay policies under consideration of localization errors....... Numerical results show how information update rates, forwarding delays, and location estimation errors affect these optimal policies and allow to conclude on the required accuracy of location-based systems for such mobile relay selection scenarios. A measurement-based indoor scenario with more complex...

  16. Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

    KAUST Repository

    Tourki, Kamel

    2011-06-01

    In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

  17. Nonconformance in electromechanical output relays of microprocessor-based protection devices under actual operating conditions

    OpenAIRE

    Gurevich, Vladimir

    2006-01-01

    Microprocessor-based protection relays are gradually driving out traditional electromechanical and even electronic protection devices from virtually all fields of power and electrical engineering. In this paper, one of many problems of microprocessor-based relays is discussed: nonconformance of miniature electromechanical output relays under actual operation conditions: switching inductive loads (with tripping CB coils or lockout relay coils) at 220 VDC, and "dry" switching of some control ci...

  18. 49 CFR 236.206 - Battery or power supply with respect to relay; location.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Battery or power supply with respect to relay..., AND APPLIANCES Automatic Block Signal Systems Standards § 236.206 Battery or power supply with respect to relay; location. The battery or power supply for each signal control relay circuit, where an open...

  19. 47 CFR 64.606 - VRS and IP Relay provider and TRS program certification.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false VRS and IP Relay provider and TRS program... Services and Related Customer Premises Equipment for Persons With Disabilities § 64.606 VRS and IP Relay... including notification in the Federal Register. (2) VRS and IP Relay provider. Any entity desiring to...

  20. Deep space optical communication via relay satellite

    Science.gov (United States)

    Dolinar, S.; Vilnrotter, V.; Gagliardi, R.

    1981-01-01

    The application of optical communications for a deep space link via an earth-orbiting relay satellite is discussed. The system uses optical frequencies for the free-space channel and RF links for atmospheric transmission. The relay satellite is in geostationary orbit and contains the optics necessary for data processing and formatting. It returns the data to earth through the RF terrestrial link and also transmits an optical beacon to the satellite for spacecraft return pointing and for the alignment of the transmitting optics. Future work will turn to modulation and coding, pointing and tracking, and optical-RF interfacing.