WorldWideScience

Sample records for quartz crystal microbalance

  1. Quartz Crystal Microbalance Data

    Energy Technology Data Exchange (ETDEWEB)

    Baxamusa, S H

    2011-11-16

    We are using a Qpod quartz crystal microbalance (manufactured by Inficon) for use as a low-volume non-volatile residue analysis tool. Inficon has agreed to help troubleshoot some of our measurements and are requesting to view some sample data, which are attached. The basic principle of an NVR analysis is to evaporate a known volume of solvent, and weigh the remaining residue to determine the purity of the solvent. A typical NVR analysis uses 60 g of solvent and can measure residue with an accuracy of +/- 0.01 mg. The detection limit is thus (0.01 mg)/(60 g) = 0.17 ppm. We are attempting to use a quartz crystal microbalance (QCM) to make a similar measurement. The attached data show the response of the QCM as a 5-20 mg drop of solvent evaporates on its surface. The change in mass registered by the QCM after the drop evaporates is the residue that deposits on the crystal. On some measurements, the change in mass in less than zero, which is aphysical since the drop will leave behind {>=}0 mass of residue. The vendor, Inficon, has agreed to look at these data as a means to help troubleshoot the cause.

  2. Data Acquisition System for Quartz Crystal Microbalances

    Directory of Open Access Journals (Sweden)

    Kleber Romero Felizardo

    2006-02-01

    Full Text Available This work presents a data acquisition system used in a mass sensor: quartz crystal microbalance. This system reads the frequency of this sensor along the time and sends the collected data to the computer through a serial interface.

  3. Coating Characterization with the Quartz Crystal Microbalance

    Science.gov (United States)

    Sturdy, Lauren F.

    The quartz crystal microbalance is a sensitive tool that can be used to measure the mass, modulus and phase angle of films of appropriate thicknesses. It is can be applied to systems with very varied properties, from liquid to solid, and under many different conditions. In this thesis its capabilities have been used to study the properties of several different systems of relevance to the coatings, art conservation, and rubber communities, in the process of which new techniques and tools were developed to analyze data and improve QCM data collection and experimental design. Alkyd resins, which have been used in artists' paints since the twentieth century, are the subject of the first studies. Alkyds are oil-modified polyesters. These resins are of interest because of their relatively recent use in art and how little is known of the mechanical properties in the early stages of cure. The QCM was shown to be sensitive to the curing process, changes in temperature, and mass change due to exposure to water. Kinetic studies during the first days of curing showed that the curing process can be divided into three regions. The first is dominated by solvent evaporation. In the second, oxygen absorption dominates and the mechanical properties change rapidly. The final stage extends from when the film is touch dry after about a day to years and is characterized by mass loss and continued increases in the modulus. Studying the curing at different temperatures revealed that the reactions do proceed much more rapidly at higher temperatures and an overall energy of activation was calculated for the curing process. The mechanical properties of alkyd resins containing zinc oxide, a white pigment, were studied with the QCM, nanoindentation and dynamic mechanical analysis. These measurements showed increases in the modulus with the inclusion of zinc oxide, and the QCM data showed that the second region started at earlier times as the pigment concentration was increased. Linseed oil is

  4. Application of quartz crystal microbalance technology in tribological investigation

    Science.gov (United States)

    The last fifteen years have seen considerable growth in the application of quartz crystal microbalance (QCM) to explore the tribological characteristics of materials. This article reviews some of the advances made in characterizing frictional properties of materials using the QCM, especially with di...

  5. Quartz Crystal Microbalance Operation and In Situ Calibration

    Science.gov (United States)

    Albyn, K. C.

    2004-01-01

    Quartz crystal microbalances (QCMs) are commonly used to measure the rate of deposition of molecular species on a surface. The measurement is often used to select materials with a low outgassing rate for applications where the material has a line of sight to a contamination-sensitive surface. A quantitative, in situ calibration of the balance, or balances, using a pure material for which the enthalpy of sublimation is known, is described in this Technical Memorandum. Supporting calculations for surface dwell times of deposited materials and the effusion cell Clausing factor are presented along with examples of multiple QCM measurements of outgassing from a common source.

  6. Respiratory Monitoring by Porphyrin Modified Quartz Crystal Microbalance Sensors

    Directory of Open Access Journals (Sweden)

    Seung-Woo Lee

    2011-01-01

    Full Text Available A respiratory monitoring system based on a quartz crystal microbalance (QCM sensor with a functional film was designed and investigated. Porphyrins 5,10,15,20-tetrakis-(4-sulfophenyl-21H,23H-porphine (TSPP and 5,10,15,20-tetrakis-(4-sulfophenyl-21H, 23H-porphine manganese (III chloride (MnTSPP used as sensitive elements were assembled with a poly(diallyldimethyl ammonium chloride (PDDA. Films were deposited on the QCM resonators using layer-by-layer method in order to develop the sensor. The developed system, in which the sensor response reflects lung movements, was able to track human respiration providing respiratory rate (RR and respiratory pattern (RP. The sensor system was tested on healthy volunteers to compare RPs and calculate RRs. The operation principle of the proposed system is based on the fast adsorption/desorption behavior of water originated from human breath into the sensor films deposited on the QCM electrode.

  7. Quartz crystal microbalance and photoacoustic measurements in dental photocuring

    Science.gov (United States)

    Lima, Marcenilda A.; Bastos, Ivan N.; Cella, Norberto

    2016-09-01

    Photocured dental resins are used extensively in restorative procedures in dentistry. Inadequate curing reduces the lifetime of the dental restoration, and consequently it is essential to precisely measure the polymerisation kinetics. In this study, two techniques, Quartz Crystal Microbalance (QCM) and Photoacoustic Spectroscopy (PAS), were used to monitor the real-time cure and to obtain the optical absorption spectra of resins, respectively. From the PAS measurements, the precise peaks of absorption were identified, and were used as the appropriate wavelength of the photocuring light in the QCM monitoring. The combined use of these techniques allows reliable determination of the duration of the phases of physical and chemical changes that occur during photocuring. Two commercial dental resins were tested, and the results confirmed the advantages of using PAS and QCM to study polymerisation kinetics.

  8. A combined nanoplasmonic and electrodeless quartz crystal microbalance setup

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Elin M.; Langhammer, Christoph; Zoric, Igor; Kasemo, Bengt [Department of Applied Physics, Chemical Physics Group, Chalmers University of Technology, SE-41296 Gothenburg (Sweden); Edvardsson, Malin E. M. [Department of Applied Physics, Biological Physics Group, Chalmers University of Technology, SE-41296 Gothenburg (Sweden)

    2009-12-15

    We have developed an instrument combining localized surface plasmon resonance (LSPR) sensing with electrodeless quartz crystal microbalance with dissipation monitoring (QCM-D). The two techniques can be run simultaneously, on the same sensor surface, and with the same time resolution and sensitivity as for the individual techniques. The electrodeless QCM eliminates the need to fabricate electrodes on the quartz crystal and gives a large flexibility in choosing the surface structure and coating for both QCM-D and LSPR. The performance is demonstrated for liquid phase measurements of lipid bilayer formation and biorecognition events, and for gas phase measurements of hydrogen uptake/release by palladium nanoparticles. Advantages of using the combined equipment for biomolecular adsorption studies include synchronized information about structural transformations and extraction of molecular (dry) mass and degree of hydration of the adlayer, which cannot be obtained with the individual techniques. In hydrogen storage studies the combined equipment, allows for synchronized measurements of uptake/release kinetics and quantification of stored hydrogen amounts in nanoparticles and films at practically interesting hydrogen pressures and temperatures.

  9. The Quartz-Crystal Microbalance in an Undergraduate Laboratory Experiment: I. Fundamentals and Instrumentation

    Science.gov (United States)

    Tsionsky, Vladimir

    2007-01-01

    The fundamentals, as well as the instrumentation of the quartz-crystal microbalance (QCM) technique that is used in an undergraduate laboratory experiment are being described. The QCM response can be easily used to change the properties of any system.

  10. Molecular Imprinting Technology in Quartz Crystal Microbalance (QCM) Sensors.

    Science.gov (United States)

    Emir Diltemiz, Sibel; Keçili, Rüstem; Ersöz, Arzu; Say, Rıdvan

    2017-02-24

    Molecularly imprinted polymers (MIPs) as artificial antibodies have received considerable scientific attention in the past years in the field of (bio)sensors since they have unique features that distinguish them from natural antibodies such as robustness, multiple binding sites, low cost, facile preparation and high stability under extreme operation conditions (higher pH and temperature values, etc.). On the other hand, the Quartz Crystal Microbalance (QCM) is an analytical tool based on the measurement of small mass changes on the sensor surface. QCM sensors are practical and convenient monitoring tools because of their specificity, sensitivity, high accuracy, stability and reproducibility. QCM devices are highly suitable for converting the recognition process achieved using MIP-based memories into a sensor signal. Therefore, the combination of a QCM and MIPs as synthetic receptors enhances the sensitivity through MIP process-based multiplexed binding sites using size, 3D-shape and chemical function having molecular memories of the prepared sensor system toward the target compound to be detected. This review aims to highlight and summarize the recent progress and studies in the field of (bio)sensor systems based on QCMs combined with molecular imprinting technology.

  11. Molecular Imprinting Technology in Quartz Crystal Microbalance (QCM Sensors

    Directory of Open Access Journals (Sweden)

    Sibel Emir Diltemiz

    2017-02-01

    Full Text Available Molecularly imprinted polymers (MIPs as artificial antibodies have received considerable scientific attention in the past years in the field of (biosensors since they have unique features that distinguish them from natural antibodies such as robustness, multiple binding sites, low cost, facile preparation and high stability under extreme operation conditions (higher pH and temperature values, etc.. On the other hand, the Quartz Crystal Microbalance (QCM is an analytical tool based on the measurement of small mass changes on the sensor surface. QCM sensors are practical and convenient monitoring tools because of their specificity, sensitivity, high accuracy, stability and reproducibility. QCM devices are highly suitable for converting the recognition process achieved using MIP-based memories into a sensor signal. Therefore, the combination of a QCM and MIPs as synthetic receptors enhances the sensitivity through MIP process-based multiplexed binding sites using size, 3D-shape and chemical function having molecular memories of the prepared sensor system toward the target compound to be detected. This review aims to highlight and summarize the recent progress and studies in the field of (biosensor systems based on QCMs combined with molecular imprinting technology.

  12. Ultrasensitive quartz crystal microbalance integrated with carbon nanotubes

    Science.gov (United States)

    Goyal, Abhijat

    In this thesis, an ultrasensitive Quartz Crystal Microbalance (QCM) which can be configured as a versatile (bio)chemical sensor is presented. The high sensitivity of the QCM was achieved via miniaturization using micromachining techniques. The absolute mass sensitivity of sensor was increased by decreasing the thickness and the area of the electrodes of the resonators. Through optimal design, microfabrication, and miniaturization the mass sensitivity of the sensors was increased by more than four orders of magnitude to less than 1 pg/Hz; as compared to 17 ng/Hz for commercially available 5 MHz bulk resonators. Miniaturization of the resonators enables their fabrication in an array format with each pixel of the array being individually addressed. This enables true spatial and temporal mass sensing capabilities. The fabricated resonators were tested for operation in air and water and high quality factors of 7500 and ˜2000 were obtained respectively. A dielectric etch process was developed to achieve the miniaturization of the sensors. The optimization of the dielectric etch process was achieved using statistical techniques such as Design of Experiment (DOE). An etch rate of 0.5 microm/min at rms surface roughness of less than 2 nm was achieved after the optimization process. The process parameters, namely the ICP power, the substrate power, the flow rate of gases, the operating pressure of the etch tool, distance of substrate holder from the source, and the temperature of substrate holder, were quantitatively related to the etch rate and rms surface roughness using least square fit to the etch data. The QCMs were integrated with carbon nanotubes using a simple spray-on technique. It was found that the addition of carbon nanotubes onto the electroded surface of the resonator increased its Q-factor by as much as 100%. It was proposed that the carbon nanotubes due to their high stiffness suppress the out-of-plane flexural vibrations in the QCMs thereby suppressing an

  13. The quartz crystal microbalance in soft matter research fundamentals and modeling

    CERN Document Server

    Johannsmann, Diethelm

    2014-01-01

    This book describes the physics of the second-generation quartz crystal microbalance (QCM), a fundamental method of analysis for soft matter at interfaces.From a device for measuring film thickness in vacuum, the quartz crystal microbalance (QCM) has in the past two decades evolved into a versatile instrument for analyzing soft matter at solid/liquid and solid/gas interfaces that found applications in diverse fields including the life sciences, material science, polymer research and electrochemistry. As a consequence of this success, the QCM is now being used by scientists with a wide variety

  14. The Quartz-Crystal Microbalance in an Undergraduate Laboratory Experiment: Measuring Mass

    Science.gov (United States)

    Tsionsky, Vladimir

    2007-01-01

    The study explains the quartz-crystal microbalance (QCM) technique, which is often used as an undergraduate laboratory experiment for measuring the mass of a system. QCM can be used as a mass sensor only when the measured mass is rigidly attached to the surface.

  15. Electrochemical Quartz Crystal Microbalance Monitoring of the Cyclic Voltammetric Deposition of Polyaniline

    Science.gov (United States)

    Xie, Qingji; Li, Zhili; Deng, Chunyan; Liu, Meiling; Zhang, Youyu; Ma, Ming; Xia, Shaoxi; Xiao, Xiaoming; Yin, Dulin; Yao, Shouzhuo

    2007-01-01

    A real-time, labeled-free and nanogram-sensitive mass sensor, electrochemical quartz crystal microbalance (EQCM) is used to monitor a cyclic voltammetric deposition of polyaniline (PANI). The results determined that the efficiency for PANI deposition and the anion-doping ratio is calculated in one single cyclic voltammetric.

  16. The Quartz-Crystal Microbalance in an Undergraduate Laboratory Experiment II: Measuring Viscosity

    Science.gov (United States)

    Tsionsky, Vladimir

    2007-01-01

    Various water-alcohol and alcohol-alcohol based experiments are used to demonstrate how the quartz-crystal microbalance (QCM) technique is used for measuring the viscosity of a system. The technique is very advantageous, as it is inexpensive and provides digital output.

  17. Ion effects in the adsorption of carboxylate on oxide surfaces, studied with quartz crystal microbalance

    NARCIS (Netherlands)

    Wang, Lei; Siretanu, Igor; Duits, Michel H.G.; Cohen Stuart, Martien A.; Mugele, Frieder

    2016-01-01

    We chose water-soluble sodium hexanoate as a model organic molecule to study the role of salt ions (Ca2+, Na+, Cl−) in the adsorption of carboxylates to mineral surfaces (silica, alumina, gibbsite) of variable surface charge and chemistry. Quartz crystal microbalance (QCM-D) measurements reveal a qu

  18. Rapid identification of spinal ventral and dorsal roots using a quartz crystal microbalance

    Institute of Scientific and Technical Information of China (English)

    Tao Sui; Jun Que; Dechao Kong; Hao Xie; Daode Wang; Kun Shi; Xiaojian Cao; Xiang Li

    2013-01-01

    The fast and accurate identification of nerve tracts is critical for successful nerve anastomosis. Taking advantage of differences in acetylcholinesterase content between the spinal ventral and dorsal roots, we developed a novel quartz crystal microbalance method to distinguish between these nerves based on acetylcholinesterase antibody reactivity. The acetylcholinesterase antibody was immobilized on the electrode surface of a quartz crystal microbalance and reacted with the acetylcholinesterase in sample solution. The formed antigen and antibody complexes added to the mass of the electrode inducing a change in frequency of the electrode. The spinal ventral and dorsal roots were distinguished by the change in frequency. The ventral and dorsal roots were cut into 1 to 2-mm long segments and then soaked in 250 μL PBS. Acetylcholinesterase antibody was immobilized on the quartz crystal microbalance gold electrode surface. The results revealed that in 10 minutes, both spinal ventral and dorsal roots induced a frequency change; however, the frequency change induced by the ventral roots was notably higher than that induced by the dorsal roots. No change was induced by bovine serum albumin or PBS. These results clearly demonstrate that a quartz crystal microbalance sensor can be used as a rapid, highly sensitive and accurate detection tool for the quick identification of spinal nerve roots intraoperatively.

  19. Detection of sulfur dioxide using a piezoelectric quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes, O.M. [Instituto de Quimica de Sao Carlos (Brazil)

    1997-09-01

    Sulfur dioxide was detected and determined in air by a piezoelectric quartz crystal sensor coated with 4-aminoantipyrine/1-hydroxyetil-2-heptadecenyl imidazol (amine 220) solution (1:1 v/v in chloroform). The analytical response curve is linear over the concentration range from 0.70 to 5.0 ppm of SO{sub 2}. Good linearities (r = 0.9990, 0.9995 and 0.9968) and sensitivities (18.0, 33.4 and 50.7 Hz/ppm) were found, respectively for exposure times of 30, 60 and 90 seconds. The sensor can be used for more than six months without loss in sensitivity and presented good reversibility and reproducibility. Among some possible interferents tested, only nitrogen dioxide and moisture caused major frequency changes.

  20. Quartz Crystal Microbalance: A tool for analyzing loss of volatile compounds, gas sorption, and curing kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Bajric, Sendin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-16

    Los Alamos National Laboratory (LANL) has recently procured a quartz crystal microbalance (QCM). Current popular uses are biological sensors, surface chemistry, and vapor detection. LANL has projects related to analyzing curing kinetics, measuring gas sorption on polymers, and analyzing the loss of volatile compounds in polymer materials. The QCM has yet to be employed; however, this review will cover the use of the QCM in these applications and its potential.

  1. Development of 170 MHz Electrodeless Quartz-Crystal Microbalance Immunosensor with Nonspecifically Immobilized Receptor Proteins

    Science.gov (United States)

    Ogi, Hirotsugu; Nagai, Hironao; Fukunishi, Yuji; Yanagida, Taiji; Hirao, Masahiko; Nishiyama, Masayoshi

    2010-07-01

    Staphylococcus aureus protein A (SPA) shows high nonspecific binding affinity on a naked quartz surface, and it can be used as the receptor protein for detecting immunoglobulin G (IgG), the most important immunoglobulin. The immunosensor ability, however, significantly depends on the immobilization procedure. In this work, the effect of the nonspecific immobilization procedure on the sensor sensitivity is studied using a home-built electrodeless quartz-crystal microbalance (QCM) biosensor. The pure-shear vibration of a 9.7-µm-thick AT-cut quartz plate is excited and detected in liquids by the line antenna located outside the flow channel. SPA molecules are immobilized on the quartz surfaces, and human IgG is injected to monitor the binding reaction between SPA and IgG. This study reveals that a long (nearly 24 h) immersion procedure is required for immobilizing SPA to achieve the tight biding with the quartz surfaces.

  2. Frequency Behavior of a Quartz Crystal Microbalance (Qcm in Contact with Selected Solutions

    Directory of Open Access Journals (Sweden)

    Z. A. Talib

    2006-01-01

    Full Text Available A device was constructed to monitor viscosity of solutions using fundamental frequency of 9 MHz and 10 MHz quartz crystal. Piezoelectric quartz crystals with gold electrodes were mounted by O-ring in between liquid flow cell. Only one side of the crystal was exposed to the solutions which were pumped through silicon tube by a peristaltic pump. The measured frequency shift was observed in order to investigate the interfacial behavior of some selected solution in contact with one surface of Quartz Crystal Microbalance (QCM. An analysis of the interaction between an AT-cut quartz crystal microbalance and various liquid system of analytical interest is presented. The analysis which includes piezoelectric effects and other influences; liquid properties, experimental conditions and the characteristic of the solution are reported. Oscillation in distilled water is taken as a reference. The frequency change caused by the density (ρ, gcm-3 and viscosity (η gcm-1s-1 were found to be proportional to the square root of the product, (ρ η. The result suggested that analysis of small frequency shifts during EQCM studies needs to account for changes in ρ and η of the solution. Generally, all the liquid tested showed an increment of the frequency shift with increasing content of solutes. For each solution, the frequency was recorded as the concentration increases from distilled water to a very concentrated solution. The frequency measurements carried out for saccharide solution produces the maximum changes of frequency shift compared with other solutions.

  3. Quartz Crystal Microbalance Technique for in Situ Analysis of Supersaturation in Cooling Crystallization.

    Science.gov (United States)

    Liu, Li-Shang; Kim, Jong-Min; Kim, Woo-Sik

    2016-06-07

    A quartz crystal microbalance (QCM) is used as a novel in situ strategy for analyzing the supersaturation profile during cooling crystallization. The main concept is based on preventing any solid mass loading on the QCM sensor by modifying the sensor surface. As a result, the QCM responses only depend on the solution concentration changes during the crystallization. The proposed strategy is confirmed on the basis of an analysis of sulfamerazine (SMZ) crystallization. When the QCM sensor is modified using 11-amino-1-undecanethiol (AUT), crystal formation on the sensor is completely prevented due to a repulsive interaction between the -NH2 functional groups of the AUT and SMZ crystals. Thus, the QCM responses reflect only the property changes in the solution phase during the crystallization. The supersaturation in the solution is then estimated on the basis of the difference in the frequency shifts between the SMZ solution and a blank solution. The accuracy of the in situ QCM analysis of supersaturation is confirmed using an off-line gravimetric method.

  4. Performances and limits of a parallel oscillator for electrochemical quartz crystal microbalances.

    Science.gov (United States)

    Ehahoun, Hervé; Gabrielli, Claude; Keddam, Michel; Perrot, Hubert; Rousseau, Philippe

    2002-03-01

    This paper describes a driving circuit for an electrochemical quartz crystal microbalance (EQCM) adapted to a wide range of applications. The oscillator is a Miller-type parallel oscillator using an operational transconductance amplifier (OTA). A theoretical study of the oscillating circuit led to the analytical expression of the microbalance frequency as well as to an overestimation of the error on the mass measurement. The reliability of the EQCM was then experimentally verified through electrochemical copper deposition and dissolution. The limit of operation of the EQCM was also investigated, both analytically and experimentally. This work shows that parallel oscillators using few electronic components allow a very reliable EQCM to be obtained for mass measurements on metallic films, even if they are highly damped.

  5. A quartz-crystal-microbalance technique to investigate ion-induced erosion of fusion relevant surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Golczewski, A. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria)], E-mail: golczewski@iap.tuwien.ac.at; Dobes, K.; Wachter, G.; Schmid, M. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria); Aumayr, F. [Institut fuer Allgemeine Physik, TU Wien, Wiedner Hauptstr. 8-10/E134, Association EURATOM-OAW, A-1040 Vienna (Austria)], E-mail: aumayr@iap.tuwien.ac.at

    2009-02-15

    We describe a highly sensitive quartz-crystal-microbalance technique capable of determining erosion as well as implantation and retention rates for fusion relevant surfaces under ion bombardment. Total sputtering yields obtained with this technique for Ar ion impact on polycrystalline gold and tungsten surfaces are presented. The results compare well with existing experimental data as well as theoretical predictions and thus demonstrate the feasibility of the developed technique. Our setup is capable of detecting mass-changes as small as 10{sup -5} {mu}g/s, which corresponds to a removal of only 10{sup -4} W monolayers/s.

  6. Quartz crystal microbalance for the cardiac markers/antibodies binding kinetic measurements in the plasma samples

    Science.gov (United States)

    Agafonova, L. E.; Shumyantseva, V. V.; Archakov, A. I.

    2014-06-01

    The quartz crystal microbalance (QCM) was exploited for cardiac markers detection and kinetic studies of immunochemical reaction of cardiac troponin I (cTnI) and human heart fatty acid binding protein (H-FABP) with the corresponding monoclonal antibodies in undiluted plasma (serum) and standard solutions. The QCM technique allowed to dynamically monitor the kinetic differences in specific interactions and nonspecific sorption, without multiple labeling procedures and separation steps. The affinity binding process was characterized by the association (ka) and the dissociation (kd) kinetic constants and the equilibrium association (K) constant, all of which were obtained from experimental data.

  7. Electroacoustic polymer microchip as an alternative to quartz crystal microbalance for biosensor development.

    Science.gov (United States)

    Gamby, Jean; Lazerges, Mathieu; Girault, Hubert H; Deslouis, Claude; Gabrielli, Claude; Perrot, Hubert; Tribollet, Bernard

    2008-12-01

    Laser photoablation of poly(ethylene terephthalate) (PET), a flexible dielectric organic polymer, was used to design an acoustic miniaturized DNA biosensor. The microchip device includes a 100-microm-thick PET layer, with two microband electrodes patterned in photoablated microchannels on one side and a depressed photoablated disk decorated by gold sputtered layer on the other side. Upon application of an electric signal between the two electrodes, an electroacoustic resonance phenomenon at approximately 30 MHz was established through the microelectrodes/PET/ gold layer interface. The electroacoustic resonance response was fitted with a series RLC motional arm in parallel with a static Co arm of a Buttlerworth-Van Dyke equivalent circuit: admittance spectra recorded after successive cycles of DNA hybridization on the gold surface showed reproducible changes on R, L, and C parameters. The same hybridizations runs were performed concomitantly on a 27-MHz (9 MHz, third overtone) quartz crystal microbalance in order to validate the PET device developed for bioanalysis applications. The electroacoustic PET device, approximately 100 times smaller than a microbalance quartz crystal, is interesting for the large-scale integration of acoustic sensors in biochips.

  8. Combined optical second harmonic generation/quartz crystal microbalance study of underpotential deposition processes: copper electrodeposition on polycrystalline gold.

    Science.gov (United States)

    Lakkaraju, S; Bennahmias, M J; Borges, G L; Gordon Ii, J G; Lazaga, M; Stone, B M; Ashley, K

    1990-11-20

    Optical second harmonic generation and quartz crystal microbalance techniques are used as in situ probes of copper underpotential deposition on polycrystalline gold surfaces in sulfuric acid electrolyte. The second harmonic signal from a polished bulk gold substrate is observed to decrease by >60% as a result of copper underpotential deposition on gold. Also, the mass of an underpotentially deposited copper adlayer is monitored in situ by an oscillating quartz crystal microbalance, yielding an estimated coverage of ~8.0 x 10(-10) mol cm(-2) and an electrosorption valency of 1.5 for a copper adlayer on the surface of vapor-deposited polycrystalline gold.

  9. Quantitative determination of hydrogen absorption by Pd cluster-assembled films using a quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    El Far, R.; Diaz-Droguett, D.E.; Rojas, S.; Avila, J.I. [Laboratorio de Ciencia de Materiales, Facultad de Fisica, Pontificia Universidad Catolica de Chile, Santiago (Chile); Romero, C.P.; Lievens, P. [Laboratorium voor Vaste-Stoffysica en Magnetisme, KU Leuven, Celestijnenlaan 200D-bus 2414 B-3001 Leuven (Belgium); Cabrera, A.L., E-mail: acabrera@fis.puc.cl [Laboratorio de Ciencia de Materiales, Facultad de Fisica, Pontificia Universidad Catolica de Chile, Santiago (Chile)

    2012-11-01

    We have measured hydrogen absorption capacity for a series of Pd films grown by two deposition techniques: a) flat films made with e-beam evaporation of Pd and b) films made of assembled Pd clusters. The films range in thickness from 9.5 to 45 nm. The technique implemented for measuring the amount of hydrogen absorbed by the films was a quartz crystal microbalance. The Pd films were grown on the quartz crystals and the change of mass due to the hydrogen absorption was determined from the shifting of the resonance frequency. Minute amounts of hydrogen absorbed of the order of nanograms per square centimeter can be detected by this technique. Plots of H/Pd atom ratio for each Pd film as a function of hydrogen pressure were obtained. The Pd e-beam grown films displayed a saturation H/Pd atomic ratio around 0.6 which is similar to bulk Pd. The Pd cluster film with a thickness of 14 nm displayed a remarkable absorption capacity with a ratio H/(Pd) Almost-Equal-To 0.84. - Highlights: Black-Right-Pointing-Pointer Pd cluster assembled films with different thicknesses are made and characterized. Black-Right-Pointing-Pointer Quartz crystal microbalance is used to quantification the hydrogen amount absorbed. Black-Right-Pointing-Pointer Hydrogen absorption/adsorption by Pd film is explained. Black-Right-Pointing-Pointer Absorption expressed in H/Pd mass ratio is given for all Pd films. Black-Right-Pointing-Pointer This complements H{sub 2} absorption on metal cluster films using optical techniques.

  10. Quartz Crystal Microbalance with Dissipation (QCM-D) studies of the viscoelastic response from a continuously growing grafted polyelectrolyte layer

    DEFF Research Database (Denmark)

    Dunér, Gunnar; Thormann, Esben; Dedinaite, Andra

    2013-01-01

    Poly(acrylic acid) was grown from substrates by photopolymerization, and the grafting process was monitored in situ by Quartz Crystal Microbalance with Dissipation (QCM-D) measurements in a 1:1 v/v mixture of water/ethanol. The polymerization process was monitored into the thick film region, where...

  11. Quartz Crystal Microbalance Investigation of the Structure of Adsorbed Soybean Oil and Methyl Oleate onto Steel Surface

    Science.gov (United States)

    The adsorption of soybean oil (SBO) and methyl oleate (MO) onto steel was investigated using quartz crystal microbalance with dissipation monitoring (QCM-D). Adsorption of both SBO and MO increased with increasing concentrations. At full surface coverage, SBO and MO formed rigid thin films and ach...

  12. In-situ monitoring of potential enhanced DNA related processes using electrochemical quartz crystal microbalance with dissipation (EQCM-D)

    DEFF Research Database (Denmark)

    Quan, Xueling; Heiskanen, Arto; Tenje, Maria

    2014-01-01

    The effect of applied potential pulses on DNA functionalization (thiolated single stranded DNA) and hybridization processes has been monitored in-situ on gold surfaces using electrochemical quartz crystal microbalance with dissipation (EQCM-D). The applied potentials were chosen with respect to t...

  13. Optimization of the hybrid bilayer membrane method for immobilization of avidin on quartz crystal microbalance.

    Science.gov (United States)

    Mun, Saem; Choi, Suk-Jung

    2009-04-15

    Hybrid bilayer membrane (HBM), comprising a lipid monolayer fused to a hydrophobic self-assembled monolayer (SAM), has a potential capability to provide a convenient tool for the preparation of functionalized sensor surfaces. In this work, the HBM approach was optimized for the preparation of avidin-containing quartz crystal microbalance (QCM) sensor chip which would be available for immobilization of biotinylated molecules. Lipid layer of HBM was composed of background lipid such as egg phosphatidyl choline and biotinylated lipid to which avidin was attached. Highest performance was obtained at 1:1 ratio of the biotinylated lipid and the background lipid, and sensitivity and stability of the resulting sensor chip was comparable to a sensor chip prepared by the conventional carbodiimide reaction. By utilizing the HBM method, construction of a stable avidin sensor chip was achieved within 40 min without any chemical steps. Thus the HBM method was proven to be a convenient and efficient way to immobilize avidin on sensor surfaces.

  14. Quartz Crystal Microbalances for quantitative picosecond laser-material-interaction investigations - Part I: Technical considerations

    Science.gov (United States)

    Gierse, N.; Schildt, T.; Esser, H. G.; Sergienko, G.; Brezinsek, S.; Freisinger, M.; Zhao, D.; Ding, H.; Terra, A.; Samm, U.; Linsmeier, Ch.

    2016-12-01

    In this work the technical suitability of Quartz Crystal Microbalances (QMBs) for in situ, pulse resolved mass removal measurements is demonstrated for picosecond laser ablation of magnetron sputtered coatings. The QMBs show a linear characteristic of the sensitivity for layer thickness of different metals up to several microns. Laser pulse resolved measurements of the mass ablated from the metal layer were performed. About 400 ng of chromium was ablated during the first laser pulse while in subsequent pulses ablation of the QMBs is found to be larger than for deposition, which is explained by the radial sensitivity of the QMBs. Future refinements of the setup and the benefits of the pulse resolved mass loss measurements for laser based methods like LIBS and LIAS are discussed and will be presented in part II currently in preparation.

  15. Separate density and viscosity measurements of unknown liquid using quartz crystal microbalance

    Directory of Open Access Journals (Sweden)

    Feng Tan

    2016-09-01

    Full Text Available Aqueous liquids have a wide range of applications in many fields. Basic physical properties like the density and the viscosity have great impacts on the functionalities of a given ionic liquid. For the millions kinds of existing liquids, only a few have been systematically measured with the density and the viscosity using traditional methods. However, these methods are limited to measure the density and the viscosity of an ionic liquid simultaneously especially in processing micro sample volumes. To meet this challenge, we present a new theoretical model and a novel method to separate density and viscosity measurements with single quartz crystal microbalance (QCM in this work. The agreement of experimental results and theocratical calculations shows that the QCM is capable to measure the density and the viscosity of ionic liquids.

  16. New Approach to a Practical Quartz Crystal Microbalance Sensor Utilizing an Inkjet Printing System

    Directory of Open Access Journals (Sweden)

    Yusuke Fuchiwaki

    2014-10-01

    Full Text Available The present work demonstrates a valuable approach to developing quartz crystal microbalance (QCM sensor units inexpensively for reliable determination of analytes. This QCM sensor unit is constructed by inkjet printing equipment utilizing background noise removal techniques. Inkjet printing equipment was chosen as an alternative to an injection pump in conventional flow-mode systems to facilitate the commercial applicability of these practical devices. The results demonstrate minimization of fluctuations from external influences, determination of antigen-antibody interactions in an inkjet deposition, and quantification of C-reactive protein in the range of 50–1000 ng∙mL−1. We thus demonstrate a marketable application of an inexpensive and easily available QCM sensor system.

  17. A highly sensitive humidity sensor based on a nanofibrous membrane coated quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xianfeng; Ding Bin [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620 (China); Yu Jianyong [Nanomaterials Research Center, Modern Textile Institute, Donghua University, Shanghai 200051 (China); Wang, Moran [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Pan Fukui, E-mail: binding@dhu.edu.cn [College of Textiles and Fashion, Qingdao University, Qingdao 266071 (China)

    2010-02-05

    A novel humidity sensor was fabricated by electrospinning deposition of nanofibrous polyelectrolyte membranes as sensitive coatings on a quartz crystal microbalance (QCM). The results of sensing experiments indicated that the response of the sensors increased by more than two orders of magnitude with increasing relative humidity (RH) from 6 to 95% at room temperature, exhibiting high sensitivity, and that, in the range of 20-95% RH, the Log({Delta}f) showed good linearity. The sensitivity of fibrous composite polyacrylic acid (PAA)/poly(vinyl alcohol) (PVA) membranes was two times higher than that of the corresponding flat films at 95% RH. Compared with fibrous PAA/PVA membranes, the nanofibrous PAA membranes exhibited remarkably enhanced humidity sensitivity due to their high PAA content and large specific surface area caused by the formation of ultrathin nanowebs among electrospun fibers. Additionally, the resultant sensors exhibited a good reversible behavior and good long term stability.

  18. A highly sensitive humidity sensor based on a nanofibrous membrane coated quartz crystal microbalance

    Science.gov (United States)

    Wang, Xianfeng; Ding, Bin; Yu, Jianyong; Wang, Moran; Pan, Fukui

    2010-02-01

    A novel humidity sensor was fabricated by electrospinning deposition of nanofibrous polyelectrolyte membranes as sensitive coatings on a quartz crystal microbalance (QCM). The results of sensing experiments indicated that the response of the sensors increased by more than two orders of magnitude with increasing relative humidity (RH) from 6 to 95% at room temperature, exhibiting high sensitivity, and that, in the range of 20-95% RH, the Log(Δf) showed good linearity. The sensitivity of fibrous composite polyacrylic acid (PAA)/poly(vinyl alcohol) (PVA) membranes was two times higher than that of the corresponding flat films at 95% RH. Compared with fibrous PAA/PVA membranes, the nanofibrous PAA membranes exhibited remarkably enhanced humidity sensitivity due to their high PAA content and large specific surface area caused by the formation of ultrathin nanowebs among electrospun fibers. Additionally, the resultant sensors exhibited a good reversible behavior and good long term stability.

  19. Quartz-Crystal Microbalance (QCM) for Public Health: An Overview of Its Applications.

    Science.gov (United States)

    Bragazzi, Nicola Luigi; Amicizia, Daniela; Panatto, Donatella; Tramalloni, Daniela; Valle, Ivana; Gasparini, Roberto

    2015-01-01

    Nanobiotechnologies, from the convergence of nanotechnology and molecular biology and postgenomics medicine, play a major role in the field of public health. This overview summarizes the potentiality of piezoelectric sensors, and in particular, of quartz-crystal microbalance (QCM), a physical nanogram-sensitive device. QCM enables the rapid, real time, on-site detection of pathogens with an enormous burden in public health, such as influenza and other respiratory viruses, hepatitis B virus (HBV), and drug-resistant bacteria, among others. Further, it allows to detect food allergens, food-borne pathogens, such as Escherichia coli and Salmonella typhimurium, and food chemical contaminants, as well as water-borne microorganisms and environmental contaminants. Moreover, QCM holds promises in early cancer detection and screening of new antiblastic drugs. Applications for monitoring biohazards, for assuring homeland security, and preventing bioterrorism are also discussed.

  20. Electrochemical quartz crystal microbalance (EQCM) study of ion dynamics in nanoporous carbons.

    Science.gov (United States)

    Tsai, Wan-Yu; Taberna, Pierre-Louis; Simon, Patrice

    2014-06-18

    Electrochemical quartz crystal microbalance (EQCM) and cyclic voltammetry (CV) measurements were used to characterize ion adsorption in carbide-derived carbon (CDC) with two different average pore sizes (1 and 0.65 nm), from neat and solvated 1-Ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMI-TFSI) electrolytes. From the electrode mass change in neat EMI-TFSI, it was shown that one net charge stored corresponds almost to one single ion at high polarization; in that case, no ion-pairing or charge screening by co-ions were observed. In 2 M EMI-TFSI in acetonitrile electrolyte, experimental solvation numbers were estimated for EMI(+) cation, showing a partial desolvation when cations were adsorbed in confined carbon pores. The extent of desolvation increased when decreasing the carbon pore size (from 1 down to 0.65 nm). The results also suggest that EMI(+) cation owns higher mobility than TFSI(-) anion in these electrolytes.

  1. Development of a Quartz Crystal Microbalance Biosensor with Aptamers as Bio-recognition Element

    Directory of Open Access Journals (Sweden)

    Chunyan Yao

    2010-06-01

    Full Text Available The ultimate goal in any biosensor development project is its use for actual sample detection. Recently, there has been an interest in biosensors with aptamers as bio-recognition elements, but reported examples all deal with standards, not human serum. In order to verify the differences of aptamer-based biosensor and antibody-based biosensor in clinical detection, a comparison of the performance of aptamer-based and antibody-based quartz crystal microbalance (QCM biosensors for the detection of immunoglobulin E (IgE in human serum was carried out. Aptamers (or antibodies specific to IgE were immobilized on the gold surface of a quartz crystal. The frequency shifts of the QCM were measured. The linear range with the antibody (10–240 μg/L compared to that of the aptamer (2.5–200 μg/L, but a lower detection limit could be observed in the aptamer-based biosensor. The reproducibility of the two biosensors was comparable. The aptamers were equivalent or superior to antibodies in terms of specificity and sensitivity. In addition, the aptamer receptors could tolerate repeated affine layer regeneration after ligand binding and recycling of the biosensor with little loss of sensitivity. When stored for three weeks, the frequency shifts of the aptamer-coated crystals were all greater than 90% of those on the response at the first day.

  2. Effect of a Non-Newtonian Load on Signature S2 for Quartz Crystal Microbalance Measurements

    Directory of Open Access Journals (Sweden)

    Jae-Hyeok Choi

    2014-01-01

    Full Text Available The quartz crystal microbalance (QCM is increasingly used for monitoring the interfacial interaction between surfaces and macromolecules such as biomaterials, polymers, and metals. Recent QCM applications deal with several types of liquids with various viscous macromolecule compounds, which behave differently from Newtonian liquids. To properly monitor such interactions, it is crucial to understand the influence of the non-Newtonian fluid on the QCM measurement response. As a quantitative indicator of non-Newtonian behavior, we used the quartz resonator signature, S2, of the QCM measurement response, which has a consistent value for Newtonian fluids. We then modified De Kee’s non-Newtonian three-parameter model to apply it to our prediction of S2 values for non-Newtonian liquids. As a model, we chose polyethylene glycol (PEG400 with the titration of its volume concentration in deionized water. As the volume concentration of PEG400 increased, the S2 value decreased, confirming that the modified De Kee’s three-parameter model can predict the change in S2 value. Collectively, the findings presented herein enable the application of the quartz resonator signature, S2, to verify QCM measurement analysis in relation to a wide range of experimental subjects that may exhibit non-Newtonian behavior, including polymers and biomaterials.

  3. Lectin typing of Campylobacter jejuni using a novel quartz crystal microbalance technique

    Energy Technology Data Exchange (ETDEWEB)

    Yakovleva, Maria E., E-mail: maria.yakovleva@gmail.com [Department of Infectious Diseases and Medical Microbiology, Lund University, 223 62 Lund (Sweden); Moran, Anthony P. [Department of Microbiology, School of Natural Sciences, National University of Ireland, Galway (Ireland); Safina, Gulnara R. [Department of Analytical and Marine Chemistry, University of Gothenburg, 412 96 Gothenburg (Sweden); Wadstroem, Torkel [Department of Infectious Diseases and Medical Microbiology, Lund University, 223 62 Lund (Sweden); Danielsson, Bengt [Acromed Invest AB, Magistratsvaegen 10, 226 43 Lund (Sweden)

    2011-05-23

    Seven Campylobacter jejuni strains were characterised by a lectin typing assay. The typing system was based on a quartz crystal microbalance technique (QCM) with four commercially available lectins (wheat germ agglutinin, Maackia amurensis lectin, Lens culinaris agglutinin, and Concanavalin A), which were chosen for their differing carbohydrate specificities. Initially, the gold surfaces of the quartz crystals were modified with 11-mercaptoundecanoic acid followed by lectin immobilisation using a conventional amine-coupling technique. Bacterial cells were applied for lectin typing without preliminary treatment, and resonant frequency and dissipation responses were recorded. The adhesion of microorganisms on lectin surfaces was confirmed by atomic force microscopy. Scanning was performed in the tapping mode and the presence of bacteria on lectin-coated surfaces was successfully demonstrated. A significant difference in the dissipation response was observed for different C. jejuni strains which made it possible to use this parameter for discriminating between bacterial strains. In summary, the QCM technique proved a powerful tool for the recognition and discrimination of C. jejuni strains. The approach may also prove applicable to strain discrimination of other bacterial species, particularly pathogens.

  4. Detection of label-free cancer biomarkers using nickel nanoislands and quartz crystal microbalance.

    Science.gov (United States)

    Martínez-Rivas, Adrián; Chinestra, Patrick; Favre, Gilles; Pinaud, Sébastien; Séverac, Childérick; Faye, Jean-Charles; Vieu, Christophe

    2010-09-07

    We present a technique for the label-free detection and recognition of cancer biomarkers using metal nanoislands intended to be integrated in a novel type of nanobiosensor. His-tagged (scFv)-F7N1N2 is the antibody fragment which is directly immobilized, by coordinative bonds, onto ~5 nm nickel islands, then deposited on the surface of a quartz crystal of a quartz crystal microbalance (QCM) to validate the technique. Biomarker GTPase RhoA was investigated because it has been found to be overexpressed in various tumors and because we have recently isolated and characterized a new conformational scFv which selectively recognizes the active form of RhoA. We implemented a surface chemistry involving an antibiofouling coating of polyethylene glycol silane (PEG-silane) (<2 nm thick) and Ni nanoislands to reach a label-free detection of the active antigen conformation of RhoA, at various concentrations. The methodology proposed here proves the viability of the concept by using Ni nanoislands as an anchoring surface layer enabling the detection of a specific conformation of a protein, identified as a potential cancer biomarker. Hence, this novel methodology can be transferred to a nanobiosensor to detect, at lower time consumption and with high sensitivity, specific biomolecules.

  5. Detection of label-free cancer biomarkers using nickel nanoislands and quartz crystal microbalance

    Directory of Open Access Journals (Sweden)

    Adrián Martínez-Rivas

    2010-09-01

    Full Text Available Adrián Martínez-Rivas1,2, Patrick Chinestra3,4, Gilles Favre3,4, Sébastien Pinaud1, Childérick Séverac1,2, Jean-Charles Faye3,4, Christophe Vieu1,21LAAS-CNRS; Université de Toulouse, Toulouse, France; 2Université de Toulouse, UPS, INSA, INP, ISAE; LAAS; Toulouse, France; 3INSERM U563, Université de Toulouse, CPTP, “Signalisation Cellulaire, GTPase Rho et cancers”, Toulouse, France; 4Institut Claudius Regaud, Biology Department, Toulouse, FranceAbstract: We present a technique for the label-free detection and recognition of cancer biomarkers using metal nanoislands intended to be integrated in a novel type of nanobiosensor. His-tagged (scFv-F7N1N2 is the antibody fragment which is directly immobilized, by coordinative bonds, onto ~5 nm nickel islands, then deposited on the surface of a quartz crystal of a quartz crystal microbalance (QCM to validate the technique. Biomarker GTPase RhoA was investigated because it has been found to be overexpressed in various tumors and because we have recently isolated and characterized a new conformational scFv which selectively recognizes the active form of RhoA. We implemented a surface chemistry involving an antibiofouling coating of polyethylene glycol silane (PEG-silane (<2 nm thick and Ni nanoislands to reach a label-free detection of the active antigen conformation of RhoA, at various concentrations. The methodology proposed here proves the viability of the concept by using Ni nanoislands as an anchoring surface layer enabling the detection of a specific conformation of a protein, identified as a potential cancer biomarker. Hence, this novel methodology can be transferred to a nanobiosensor to detect, at lower time consumption and with high sensitivity, specific biomolecules.Keywords: nickel nanoislands, cancer biomarkers, quartz crystal microbalance, PEG-silane, RhoA protein, nanobiosensor

  6. A Review of Interface Electronic Systems for AT-cut Quartz Crystal Microbalance Applications in Liquids

    Directory of Open Access Journals (Sweden)

    Antonio Arnau

    2008-01-01

    Full Text Available From the first applications of AT-cut quartz crystals as sensors in solutionsmore than 20 years ago, the so-called quartz crystal microbalance (QCM sensor isbecoming into a good alternative analytical method in a great deal of applications such asbiosensors, analysis of biomolecular interactions, study of bacterial adhesion at specificinterfaces, pathogen and microorganism detection, study of polymer film-biomolecule orcell-substrate interactions, immunosensors and an extensive use in fluids and polymercharacterization and electrochemical applications among others. The appropriateevaluation of this analytical method requires recognizing the different steps involved andto be conscious of their importance and limitations. The first step involved in a QCMsystem is the accurate and appropriate characterization of the sensor in relation to thespecific application. The use of the piezoelectric sensor in contact with solutions stronglyaffects its behavior and appropriate electronic interfaces must be used for an adequatesensor characterization. Systems based on different principles and techniques have beenimplemented during the last 25 years. The interface selection for the specific application isimportant and its limitations must be known to be conscious of its suitability, and foravoiding the possible error propagation in the interpretation of results. This article presentsa comprehensive overview of the different techniques used for AT-cut quartz crystalmicrobalance in in-solution applications, which are based on the following principles:network or impedance analyzers, decay methods, oscillators and lock-in techniques. Theelectronic interfaces based on oscillators and phase-locked techniques are treated in detail,with the description of different configurations, since these techniques are the most used inapplications for detection of analytes in solutions, and in those where a fast sensorresponse is necessary.

  7. A novel assay for detecting canine parvovirus using a quartz crystal microbalance biosensor.

    Science.gov (United States)

    Kim, Yong Kwan; Lim, Seong-In; Choi, Sarah; Cho, In-Soo; Park, Eun-Hye; An, Dong-Jun

    2015-07-01

    Rapid and accurate diagnosis is crucial to reduce both the shedding and clinical signs of canine parvovirus (CPV). The quartz crystal microbalance (QCM) is a new tool for measuring frequency changes associated with antigen-antibody interactions. In this study, the QCM biosensor and ProLinker™ B were used to rapidly diagnosis CPV infection. ProLinker™ B enables antibodies to be attached to a gold-coated quartz surface in a regular pattern and in the correct orientation for antigen binding. Receiver operating characteristics (ROC) curves were used to set a cut-off value using reference CPVs (two groups: one CPV-positive and one CPV-negative). The ROC curves overlapped and the point of intersection was used as the cut-off value. A QCM biosensor with a cut-off value of -205 Hz showed 95.4% (104/109) sensitivity and 98.0% (149/152) specificity when used to test 261 field fecal samples compared to PCR. In conclusion, the QCM biosensor described herein is eminently suitable for the rapid diagnosis of CPV infection with high sensitivity and specificity. Therefore, it is a promising analytical tool that will be useful for clinical diagnosis, which requires rapid and reliable analyses.

  8. Exploiting Solvate Ionic Liquids for Amine Gas Analysis on a Quartz Crystal Microbalance.

    Science.gov (United States)

    Li, Hsin-Yi; Chu, Yen-Ho

    2017-05-16

    We demonstrated in this work the usefulness of solvate ionic liquids SIL 3 and SIL 4 for chemoselective detection of amine gases on a quartz crystal microbalance. This detection of gaseous amines was achieved by nucleophilic aromatic addition reactions with super electrophilic SIL 3 or SIL 4 thin-coated on quartz chips. Starting with inexpensive reagents, functional SIL 3 and SIL 4 could be readily synthesized in two short steps with high isolated yield (81 and 77%, respectively). The QCM platform developed in this work is readily applicable and highly sensitive to low molecular weight amine gases: for propylamine gas at 10 Hz decrease in resonance frequency, the sensitivity of detection using SIL 4 was 5.4 ppb. This simple and convenient assembly of neutral ligands (e.g., 1a and 1b) with Li(+) ion to afford room temperature ionic liquids should be of great importance for a myriad of applications. To the best of our knowledge, no example to date of reports based on nucleophilic aromatic addition reactions demonstrating sensitive amine gas detection in solvate ionic liquids on a QCM has been reported. Furthermore, because of the high color intensity of the Meisenheimer complexes formed, our preliminary result showed that SIL 4 loaded on copier paper can be used not only as a portable amine gas sensor but also as a potential invisible ink that is only revealed by amine vapor.

  9. Low-cost scalable quartz crystal microbalance array for environmental sensing

    Energy Technology Data Exchange (ETDEWEB)

    Anazagasty, Cristain [University of Puerto Rico; Hianik, Tibor [Comenius University, Bratislava, Slovakia; Ivanov, Ilia N [ORNL

    2016-01-01

    Proliferation of environmental sensors for internet of things (IoT) applications has increased the need for low-cost platforms capable of accommodating multiple sensors. Quartz crystal microbalance (QCM) crystals coated with nanometer-thin sensor films are suitable for use in high-resolution (~1 ng) selective gas sensor applications. We demonstrate a scalable array for measuring frequency response of six QCM sensors controlled by low-cost Arduino microcontrollers and a USB multiplexer. Gas pulses and data acquisition were controlled by a LabVIEW user interface. We test the sensor array by measuring the frequency shift of crystals coated with different compositions of polymer composites based on poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) while films are exposed to water vapor and oxygen inside a controlled environmental chamber. Our sensor array exhibits comparable performance to that of a commercial QCM system, while enabling high-throughput 6 QCM testing for under $1,000. We use deep neural network structures to process sensor response and demonstrate that the QCM array is suitable for gas sensing, environmental monitoring, and electronic-nose applications.

  10. Low-cost scalable quartz crystal microbalance array for environmental sensing

    Science.gov (United States)

    Muckley, Eric S.; Anazagasty, Cristain; Jacobs, Christopher B.; Hianik, Tibor; Ivanov, Ilia N.

    2016-09-01

    Proliferation of environmental sensors for internet of things (IoT) applications has increased the need for low-cost platforms capable of accommodating multiple sensors. Quartz crystal microbalance (QCM) crystals coated with nanometer-thin sensor films are suitable for use in high-resolution ( 1 ng) selective gas sensor applications. We demonstrate a scalable array for measuring frequency response of six QCM sensors controlled by low-cost Arduino microcontrollers and a USB multiplexer. Gas pulses and data acquisition were controlled by a LabVIEW user interface. We test the sensor array by measuring the frequency shift of crystals coated with different compositions of polymer composites based on poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) while films are exposed to water vapor and oxygen inside a controlled environmental chamber. Our sensor array exhibits comparable performance to that of a commercial QCM system, while enabling high-throughput 6 QCM testing for under $1,000. We use deep neural network structures to process sensor response and demonstrate that the QCM array is suitable for gas sensing, environmental monitoring, and electronic-nose applications.

  11. Use of the quartz crystal microbalance to determine the monomeric friction coefficient of polyimides

    Science.gov (United States)

    Bechtold, Mary M.

    1995-01-01

    When a thin film of polymer is coated on to a quartz crystal microbalance (QCM), the QCM can be used to detect the rate of increase in weight of the polymer film as the volatile penetrant diffuses into the polymer. From this rate information the diffusion coefficient of the penetrant into the polymer can be computed. Calculations requiring this diffusion coefficient lead to values which approximate the monomeric friction coefficient of the polymer. This project has been concerned with the trial of crystal oscillating circuits suitable for driving polymer coated crystals in an atmosphere of penetrant. For these studies done at room temperature, natural rubber was used as an easily applied polymer that is readily penetrated by toluene vapors, qualities anticipated with polyimides when they are tested at T(g) in the presence of toluene. Three quartz crystal oscillator circuits were tested. The simplest circuit used +/- 5 volt dc and had a transistor to transistor logic (TTL) inverter chip that provides a 180 deg phase shift via a feed back loop. This oscillator circuit was stable but would not drive the crystal when the crystal was coated with polymer and subjected to toluene vapors. Removal of a variable resistor from this circuit increased stability but did not otherwise increase performance. Another driver circuit tested contained a two stage differential input, differential output, wide band video amplifier and also contain a feed back loop. The circuit voltage could not be varied and operated at +/- 5 volts dc; this circuit was also stable but failed to oscillate the polymer coated crystal in an atmosphere saturated with toluene vapors. The third oscillator circuit was of similar construction and relied on the same video amplifier but allowed operation with variable voltage. This circuit would drive the crystal when the crystal was submerged in liquid toluene and when the crystal was coated with polymer and immersed in toluene vapors. The frequency readings

  12. A quartz crystal microbalance sensor based on mussel-inspired molecularly imprinted polymer.

    Science.gov (United States)

    Zhou, Wen-Hui; Tang, Shui-Fen; Yao, Qiu-Hong; Chen, Fa-Rong; Yang, Huang-Hao; Wang, Xiao-Ru

    2010-10-15

    In this work, we describe a simple, inexpensive and fast method for the generation of molecularly imprinted polymer (MIP) film on quartz crystal microbalance (QCM) crystals using mussel-inspired polymer. Commonly known as a neurotransmitter, dopamine is also a small-molecule mimic of the adhesive proteins of mussels. Polymerization of dopamine in the presence of template molecule (1,3,5-pentanetricarboxylic acid, an analogue of domoic acid, in this case) could produce an adherent molecularly imprinted polydopamine film coating on QCM crystals. Advantages, such as high hydrophilicity, high biocompatibility and controllable thickness, make this molecularly imprinted polydopamine film an attractive recognition element for sensors. Selective rebinding of domoic acid on mussel-inspired molecularly imprinted polymer (m-MIP) coated crystal was observed as a frequency shift quantified by piezoelectric microgravimetry with the QCM system. The decreasing frequency shows a good linear relationship with the concentration of domoic acid. The quantitation limit of domoic acid was 5 ppb with the linear range of 0-100 ppb. The QCM sensor has high selectivity and was able to distinguish domoic acid from its analogous p-phthalic acid and o-phthalic acid owing to the molecular imprinting effect. In addition, the practical analytical performance of the sensor was examined by evaluating the detection of domoic acid in mussel extracts with satisfactory results. It is envisaged that m-MIP could be suitable as recognition element for sensors and the proposed m-MIP QCM sensor could be employed to detect analyte of interest in complex matrices. Copyright © 2010 Elsevier B.V. All rights reserved.

  13. Rancang Bangun Sistem Pencacah Frekuensi Untuk Sensor Gas Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Brilianda Adi Wicaksono

    2014-03-01

    Full Text Available Dalam suatu sistem identifikasi gas menggunakan sensor Quartz Crystal Microbalance (QCM diperlukan sebuah pencacah frekuensi yang digunakan untuk menghitung perubahan frekuensi dari sensor. Sistem ini digunakan untuk menghasilkan output berupa perubahan frekuensi yang akan diproses untuk identifikasi gas. Metode ini menggunakan selisih antara frekuensi sensor QCM dan frekuensi referensi. Hasil dari selisih tersebut dibagi dan digunakan untuk mengaktifkan pencacah frekuensi. Semakin besar bilangan pembagi, maka sistem pencacah frekuensi ini semakin stabil dan akurat. Penelitian ini menggunakan kristal referensi 20MHz dengan pencacah frekuensi 24 bit. Data hasil pencacahan diakuisisi oleh mikrokontroler dan dikirim ke komputer untuk proses identifikasi menggunakan neural network. Output dari neural network ini merupakan hasil dari proses identifikasi gas. Dengan metode yang digunakan, perubahan frekuensi yang dapat dideteksi mencapai 0,068 Hz. Dalam pengujian keseluruhan sistem digunakan 3 bahan uji, yaitu alkohol, amoniak, dan asam asetat (cuka.Untuk sistem identifikasi gas telah dapat mengenali gas uji dengan keberhasilan 90%. Secara keseluruhan, metode ini diharapkan menjadi metode yang baik untuk sistem identifikasi gas.

  14. Development of a Flow Injection Based High Frequency Dual Channel Quartz Crystal Microbalance.

    Science.gov (United States)

    Liang, Jinxing; Zhang, Jing; Zhou, Wenxiang; Ueda, Toshitsugu

    2017-05-16

    When the quartz crystal microbalance (QCM) is used in liquid for adsorption or desorption monitoring based bio- or chemical sensing applications, the frequency shift is not only determined by the surface mass change, but also by the change of liquid characteristics, such as density and viscosity, which are greatly affected by the liquid environmental temperature. A monolithic dual-channel QCM is designed and fabricated by arranging two QCM resonators on one single chip for cancelling the fluctuation induced by environmental factors. In actual applications, one QCM works as a specific sensor by modifying with functional membranes and the other acts as a reference, only measuring the liquid property. The dual-channel QCM is designed with an inverted-mesa structure, aiming to realize a high frequency miniaturized chip and suppress the frequency interference between the neighbored QCM resonators. The key problem of dual-channel QCMs is the interference between two channels, which is influenced by the distance of adjacent resonators. The diameter of the reference electrode has been designed into several values in order to find the optimal parameter. Experimental results demonstrated that the two QCMs could vibrate individually and the output frequency stability and drift can be greatly improved with the aid of the reference QCM.

  15. Biomimetic Receptors for Bioanalyte Detection by Quartz Crystal Microbalances — From Molecules to Cells

    Directory of Open Access Journals (Sweden)

    Usman Latif

    2014-12-01

    Full Text Available A universal label-free detection of bioanalytes can be performed with biomimetic quartz crystal microbalance (QCM coatings prepared by imprinting strategies. Bulk imprinting was used to detect the endocrine disrupting chemicals (EDCs known as estradiols. The estrogen 17β-estradiol is one of the most potent EDCs, even at very low concentrations. A highly sensitive, selective and robust QCM sensor was fabricated for real time monitoring of 17β-estradiol in water samples by using molecular imprinted polyurethane. Optimization of porogen (pyrene and cross-linker (phloroglucinol levels leads to improved sensitivity, selectivity and response time of the estradiol sensor. Surface imprinting of polyurethane as sensor coating also allowed us to generate interaction sites for the selective recognition of bacteria, even in a very complex mixture of interfering compounds, while they were growing from their spores in nutrient solution. A double molecular imprinting approach was followed to transfer the geometrical features of natural bacteria onto the synthetic polymer to generate biomimetic bacteria. The use of biomimetic bacteria as template makes it possible to prepare multiple sensor coatings with similar sensitivity and selectivity. Thus, cell typing, e.g., differentiation of bacteria strains, bacteria growth profile and extent of their nutrition, can be monitored by biomimetic mass sensors. Obviously, this leads to controlled cell growth in bioreactors.

  16. Hydrolysis of model cellulose films by cellulosomes: Extension of quartz crystal microbalance technique to multienzymatic complexes.

    Science.gov (United States)

    Zhou, Shanshan; Li, Hsin-Fen; Garlapalli, Ravinder; Nokes, Sue E; Flythe, Michael; Rankin, Stephen E; Knutson, Barbara L

    2017-01-10

    Bacterial cellulosomes contain highly efficient complexed cellulases and have been studied extensively for the production of lignocellulosic biofuels and bioproducts. A surface measurement technique, quartz crystal microbalance with dissipation (QCM-D), was extended for the investigation of real-time binding and hydrolysis of model cellulose surfaces from free fungal cellulases to the cellulosomes of Clostridium thermocellum (Ruminiclostridium thermocellum). In differentiating the activities of cell-free and cell-bound cellulosomes, greater than 68% of the cellulosomes in the crude cell broth were found to exist unattached to the cell across multiple growth stages. The initial hydrolysis rate of crude cell broth measured by QCM was greater than that of cell-free cellulosomes, but the corresponding frequency drop (a direct measure of the mass of enzyme adsorbed to the film) of crude cell broth was less than that of the cell-free cellulosomes, consistent with the underestimation of the cell mass adsorbed using QCM. Inhibition of hydrolysis by cellobiose (0-10g/L), which is similar for crude cell broth and cell-free cellulosomes, demonstrates the sensitivity of the QCM to environmental perturbations of multienzymatic complexes. QCM measurements using multienzymatic complexes may be used to screen and optimize hydrolysis conditions and to develop mechanistic, surface-based models of enzymatic cellulose deconstruction. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Protein Adsorption to Titanium and Zirconia Using a Quartz Crystal Microbalance Method

    Directory of Open Access Journals (Sweden)

    You Kusakawa

    2017-01-01

    Full Text Available Protein adsorption onto titanium (Ti or zirconia (ZrO2 was evaluated using a 27 MHz quartz crystal microbalance (QCM. As proteins, fibronectin (Fn, a cell adhesive protein, and albumin (Alb, a cell adhesion-inhibiting protein, were evaluated. The Ti and ZrO2 sensors for QCM were characterized by atomic force microscopy and electron probe microanalysis observation, measurement of contact angle against water, and surface roughness. The amounts of Fn and Alb adsorbed onto the Ti and ZrO2 sensors and apparent reaction rate were obtained using QCM measurements. Ti sensor showed greater adsorption of Fn and Alb than the ZrO2 sensor. In addition, amount of Fn adsorbed onto the Ti or ZrO2 sensors was higher than that of Alb. The surface roughness and hydrophilicity of Ti or ZrO2 may influence the adsorption of Fn or Alb. With regard to the adsorption rate, Alb adsorbed more rapidly than Fn onto Ti. Comparing Ti and ZrO2, Alb adsorption rate to Ti was faster than that to ZrO2. Fn adsorption will be effective for cell activities, but Alb adsorption will not. QCM method could simulate in vivo Fn and Alb adsorption to Ti or ZrO2.

  18. Protein Adsorption to Titanium and Zirconia Using a Quartz Crystal Microbalance Method

    Science.gov (United States)

    Kusakawa, You

    2017-01-01

    Protein adsorption onto titanium (Ti) or zirconia (ZrO2) was evaluated using a 27 MHz quartz crystal microbalance (QCM). As proteins, fibronectin (Fn), a cell adhesive protein, and albumin (Alb), a cell adhesion-inhibiting protein, were evaluated. The Ti and ZrO2 sensors for QCM were characterized by atomic force microscopy and electron probe microanalysis observation, measurement of contact angle against water, and surface roughness. The amounts of Fn and Alb adsorbed onto the Ti and ZrO2 sensors and apparent reaction rate were obtained using QCM measurements. Ti sensor showed greater adsorption of Fn and Alb than the ZrO2 sensor. In addition, amount of Fn adsorbed onto the Ti or ZrO2 sensors was higher than that of Alb. The surface roughness and hydrophilicity of Ti or ZrO2 may influence the adsorption of Fn or Alb. With regard to the adsorption rate, Alb adsorbed more rapidly than Fn onto Ti. Comparing Ti and ZrO2, Alb adsorption rate to Ti was faster than that to ZrO2. Fn adsorption will be effective for cell activities, but Alb adsorption will not. QCM method could simulate in vivo Fn and Alb adsorption to Ti or ZrO2. PMID:28246591

  19. Quartz Crystal Microbalance Studies of Multilayer Glucagon Fibrillation at the Solid-Liquid Interface

    Science.gov (United States)

    Hovgaard, Mads Bruun; Dong, Mingdong; Otzen, Daniel Erik; Besenbacher, Flemming

    2007-01-01

    We have used a quartz crystal microbalance with dissipation (QCM-D) to monitor the changes in layer thickness and viscoelastic properties accompanying multilayer amyloid deposition in situ for the first time. By means of atomic force microscope imaging, an unequivocal correlation is established between the interfacial nucleation and growth of glucagon fibrils and the QCM-D response. The combination of the two techniques allows us to study the temporal evolution of the interfacial fibrillation process. We have modeled the QCM-D data using an extension to the Kelvin-Voigt viscoelastic model. Three phases were observed in the fibrillation process: 1), a rigid multilayer of glucagon monomers forms and slowly rearranges; 2), this multilayer subsequently evolves into a dramatically more viscoelastic layer, containing a polymorphic network of micrometer-long fibrils growing from multiple nucleation sites; and 3), the fibrillar formation effectively stops as a result of the depletion of bulk-phase monomers, although the process can be continued without a lag phase by subsequent addition of fresh monomers. The robustness of the QCM-D technique, consolidated by complementary atomic force microscope studies, should make it possible to combine different components thought to be involved in the plaque formation process and thus build up realistic models of amyloid plaque formation in vitro. PMID:17513349

  20. Quartz crystal microbalance studies of multilayer glucagon fibrillation at the solid-liquid interface.

    Science.gov (United States)

    Hovgaard, Mads Bruun; Dong, Mingdong; Otzen, Daniel Erik; Besenbacher, Flemming

    2007-09-15

    We have used a quartz crystal microbalance with dissipation (QCM-D) to monitor the changes in layer thickness and viscoelastic properties accompanying multilayer amyloid deposition in situ for the first time. By means of atomic force microscope imaging, an unequivocal correlation is established between the interfacial nucleation and growth of glucagon fibrils and the QCM-D response. The combination of the two techniques allows us to study the temporal evolution of the interfacial fibrillation process. We have modeled the QCM-D data using an extension to the Kelvin-Voigt viscoelastic model. Three phases were observed in the fibrillation process: 1), a rigid multilayer of glucagon monomers forms and slowly rearranges; 2), this multilayer subsequently evolves into a dramatically more viscoelastic layer, containing a polymorphic network of micrometer-long fibrils growing from multiple nucleation sites; and 3), the fibrillar formation effectively stops as a result of the depletion of bulk-phase monomers, although the process can be continued without a lag phase by subsequent addition of fresh monomers. The robustness of the QCM-D technique, consolidated by complementary atomic force microscope studies, should make it possible to combine different components thought to be involved in the plaque formation process and thus build up realistic models of amyloid plaque formation in vitro.

  1. A Label-Free Immunosensor for Ultrasensitive Detection of Ketamine Based on Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Ya Yang

    2015-04-01

    Full Text Available In this study, we have developed a label-free immunosensor with the variation of resonance frequency (Δf of a quartz crystal microbalance (QCM as readout signal for ultrasensitive detection of Ketamine (KT. An optimized strategy for immobilization of KT antibody on the surface of the QCM chip was implemented via the self-assembly modification of 3-mercaptopropionic acid, and then activated with 1-ethyl-3- (3-dimethylaminoprophl carbodiimide and n-hydroxysuccinimide. The specific affinity between the antibody and the antigen ensured a selective response toward KT. The Δf linearly related to the concentration of KT in the range of 1 to 40 pg/mL, with a detection limit of 0.86 pg/mL (S/N = 3. The obtained immunosensor was applied to detect the KT in spiked human urine without any pretreatment but dilution with recoveries from 91.8% to 108%. The developed sensor is promising to perform the portable or on-spot KT detection in clinic or forensic cases.

  2. Protein Adsorption to Titanium and Zirconia Using a Quartz Crystal Microbalance Method.

    Science.gov (United States)

    Kusakawa, You; Yoshida, Eiji; Hayakawa, Tohru

    2017-01-01

    Protein adsorption onto titanium (Ti) or zirconia (ZrO2) was evaluated using a 27 MHz quartz crystal microbalance (QCM). As proteins, fibronectin (Fn), a cell adhesive protein, and albumin (Alb), a cell adhesion-inhibiting protein, were evaluated. The Ti and ZrO2 sensors for QCM were characterized by atomic force microscopy and electron probe microanalysis observation, measurement of contact angle against water, and surface roughness. The amounts of Fn and Alb adsorbed onto the Ti and ZrO2 sensors and apparent reaction rate were obtained using QCM measurements. Ti sensor showed greater adsorption of Fn and Alb than the ZrO2 sensor. In addition, amount of Fn adsorbed onto the Ti or ZrO2 sensors was higher than that of Alb. The surface roughness and hydrophilicity of Ti or ZrO2 may influence the adsorption of Fn or Alb. With regard to the adsorption rate, Alb adsorbed more rapidly than Fn onto Ti. Comparing Ti and ZrO2, Alb adsorption rate to Ti was faster than that to ZrO2. Fn adsorption will be effective for cell activities, but Alb adsorption will not. QCM method could simulate in vivo Fn and Alb adsorption to Ti or ZrO2.

  3. Electrochemical quartz crystal microbalance study of the electrodeposition of Co, Pt and Pt-Co alloy

    Energy Technology Data Exchange (ETDEWEB)

    Martin, A.J.; Chaparro, A.M. [CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain); Daza, L. [CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain); Instituto de Catalisis y Petroleoquimica (CSIC), C/Marie Curie 2, Campus Cantoblanco, 28049 Madrid (Spain)

    2007-06-10

    The electrochemical deposition of Co, Pt and Pt-Co alloy are studied with the electrochemical quartz crystal microbalance (EQCM) on a gold substrate. Co is deposited from acidic sulphate bath containing boric acid. Different processes are identified in this bath. Electrodeposition of Co on Au substrate is observed at potentials above redox potential, underpotential deposition, most probably due to formation of a Co-Au alloy. At more cathodic potentials, below -0.5 V, metallic Co is formed. The film is completely dissolved at positive potentials during the anodic scan, probably mediated by Co(OH){sub 2}. The electrodeposition of platinum from acidic PtCl{sub 6}{sup 2-} bath occurs below the thermodynamic potential (0.74 V) with almost 100% efficiency. At potentials negative from 0.0 V the efficiency decreases due to parallel water reduction. The codeposition of Co and Pt is also studied in acidic bath. Here, the decrease of pH due to water reduction on Pt deposits gives rise to precipitation of Co(OH){sub 2}, together with the deposition of metallic Pt and Co. The films contain as major component the Pt{sub 3}Co alloy. (author)

  4. Electrochemical quartz crystal microbalance study of the electrodeposition of Co, Pt and Pt-Co alloy

    Science.gov (United States)

    Martín, A. J.; Chaparro, A. M.; Daza, L.

    The electrochemical deposition of Co, Pt and Pt-Co alloy are studied with the electrochemical quartz crystal microbalance (EQCM) on a gold substrate. Co is deposited from acidic sulphate bath containing boric acid. Different processes are identified in this bath. Electrodeposition of Co on Au substrate is observed at potentials above redox potential, underpotential deposition, most probably due to formation of a Co-Au alloy. At more cathodic potentials, below -0.5 V, metallic Co is formed. The film is completely dissolved at positive potentials during the anodic scan, probably mediated by Co(OH) 2. The electrodeposition of platinum from acidic PtCl 6 2- bath occurs below the thermodynamic potential (0.74 V) with almost 100% efficiency. At potentials negative from 0.0 V the efficiency decreases due to parallel water reduction. The codeposition of Co and Pt is also studied in acidic bath. Here, the decrease of pH due to water reduction on Pt deposits gives rise to precipitation of Co(OH) 2, together with the deposition of metallic Pt and Co. The films contain as major component the Pt 3Co alloy.

  5. Probing the interaction between nanoparticles and lipid membranes by quartz crystal microbalance with dissipation monitoring

    Science.gov (United States)

    Yousefi, Nariman; Tufenkji, Nathalie

    2016-12-01

    There is increasing interest in using quartz crystal microbalance with dissipation monitoring (QCM-D) to investigate the interaction of nanoparticles (NPs) with model surfaces. The high sensitivity, ease of use and the ability to monitor interactions in real-time has made it a popular technique for colloid chemists, biologists, bioengineers and biophysicists. QCM-D has been recently used to probe the interaction of NPs with supported lipid bilayers (SLBs) as model cell membranes. The interaction of NPs with SLBs is highly influenced by the quality of the lipid bilayers. Unlike many surface sensitive techniques, using QCM-D, the quality of SLBs can be assessed in real-time, hence QCM-D studies on SLB-NP interactions are less prone to the artefacts arising from bilayers that are not well formed. The ease of use and commercial availability of a wide range of sensor surfaces also have made QCM-D a versatile tool for studying NP interactions with lipid bilayers. In this review, we summarize the state-of-the-art on QCM-D based techniques for probing the interactions of NPs with lipid bilayers.

  6. A Study of Drop-Microstructured Surface Interactions during Dropwise Condensation with Quartz Crystal Microbalance

    Science.gov (United States)

    Su, Junwei; Charmchi, Majid; Sun, Hongwei

    2016-10-01

    Dropwise condensation (DWC) on hydrophobic surfaces is attracting attention for its great potential in many industrial applications, such as steam power plants, water desalination, and de-icing of aerodynamic surfaces, to list a few. The direct dynamic characterization of liquid/solid interaction can significantly accelerate the progress toward a full understanding of the thermal and mass transport mechanisms during DWC processes. This work reports a novel Quartz Crystal Microbalance (QCM) based method that can quantitatively analyze the interaction between water droplets and micropillar surfaces during different condensation states such as filmwise, Wenzel, and partial Cassie states. A combined nanoimprinting lithography and chemical surface treatment approach was utilized to fabricate the micropillar based superhydrophobic and superhydrophilic surfaces on the QCM substrates. The normalized frequency shift of the QCM device together with the microscopic observation of the corresponding drop motion revealed the droplets growth and their coalescence processes and clearly demonstrated the differences between the three aforementioned condensation states. In addition, the transition between Cassie and Wenzel states was successfully captured by this method. The newly developed QCM system provides a valuable tool for the dynamic characterization of different condensation processes.

  7. A hybrid humidity sensor using optical waveguides on a quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Shinbo, Kazunari, E-mail: kshinbo@eng.niigata-u.ac.j [Graduate School of Science and Technology, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Center for Transdisciplinary Research, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Otuki, Shunya; Kanbayashi, Yuichi [Graduate School of Science and Technology, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Ohdaira, Yasuo [Graduate School of Science and Technology, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Center for Transdisciplinary Research, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Baba, Akira [Center for Transdisciplinary Research, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Kato, Keizo; Kaneko, Futao [Graduate School of Science and Technology, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Center for Transdisciplinary Research, Niigata University, 2-8050 Ikarashi, Nishi-ku, Niigata City, Niigata 950-2181 (Japan); Miyadera, Nobuo [Hitachi Chemical Co., Ltd., 48 Wadai, Tsukuba City, Ibaraki 300-4247 (Japan)

    2009-11-30

    In this study, slab and ridge optical waveguides (OWGs) made of fluorinated polyimides were deposited on a quartz crystal microbalance (QCM), and hybrid sensors using OWG spectroscopy and the QCM technique were prepared. Polyvinyl alcohol (PVA) film with CoCl{sub 2} was deposited on the OWGs, and the characteristics of humidity sensing were investigated. A prism coupler was used to enter a He-Ne laser beam ({lambda} = 632.8 nm) to the slab OWG. The output light intensity markedly changed due to chromism of the CoCl{sub 2} as a result of humidity sorption, and this change was dependent on the incident angle of the laser beam to the slab OWG. During the measurement of output light, the QCM frequency was simultaneously monitored. The humidity dependence of the sensor with the slab OWG was also investigated in the range from 15 to 85%. For the sensor with the ridge OWG, white light was entered by butt-coupling, and the characteristics of humidity sensing were investigated by observing the output light spectrum and the QCM frequency.

  8. Quartz crystal microbalance (QCM) affinity biosensor for genetically modified organisms (GMOs) detection.

    Science.gov (United States)

    Mannelli, Ilaria; Minunni, Maria; Tombelli, Sara; Mascini, Marco

    2003-03-01

    A DNA piezoelectric sensor has been developed for the detection of genetically modified organisms (GMOs). Single stranded DNA (ssDNA) probes were immobilised on the sensor surface of a quartz crystal microbalance (QCM) device and the hybridisation between the immobilised probe and the target complementary sequence in solution was monitored. The probe sequences were internal to the sequence of the 35S promoter (P) and Nos terminator (T), which are inserted sequences in the genome of GMOs regulating the transgene expression. Two different probe immobilisation procedures were applied: (a) a thiol-dextran procedure and (b) a thiol-derivatised probe and blocking thiol procedure. The system has been optimised using synthetic oligonucleotides, which were then applied to samples of plasmidic and genomic DNA isolated from the pBI121 plasmid, certified reference materials (CRM), and real samples amplified by the polymerase chain reaction (PCR). The analytical parameters of the sensor have been investigated (sensitivity, reproducibility, lifetime etc.). The results obtained showed that both immobilisation procedures enabled sensitive and specific detection of GMOs, providing a useful tool for screening analysis in food samples.

  9. Frequency-shift vs phase-shift characterization of in-liquid quartz crystal microbalance applications

    Energy Technology Data Exchange (ETDEWEB)

    Montagut, Y. J.; Garcia, J. V.; Jimenez, Y.; Arnau, A. [Grupo de Fenomenos Ondulatorios, Departamento de Ingenieria Electronica, Universitat Politecnica de Valencia (Spain); March, C.; Montoya, A. [Instituto Interuniversitario de Investigacion en Bioingenieria y Tecnologia Orientada al Ser Humano, Universitat Politecnica de Valencia (Spain)

    2011-06-15

    The improvement of sensitivity in quartz crystal microbalance (QCM) applications has been addressed in the last decades by increasing the sensor fundamental frequency, following the increment of the frequency/mass sensitivity with the square of frequency predicted by Sauerbrey. However, this sensitivity improvement has not been completely transferred in terms of resolution. The decrease of frequency stability due to the increase of the phase noise, particularly in oscillators, made impossible to reach the expected resolution. A new concept of sensor characterization at constant frequency has been recently proposed. The validation of the new concept is presented in this work. An immunosensor application for the detection of a low molecular weight contaminant, the insecticide carbaryl, has been chosen for the validation. An, in principle, improved version of a balanced-bridge oscillator is validated for its use in liquids, and applied for the frequency shift characterization of the QCM immunosensor application. The classical frequency shift characterization is compared with the new phase-shift characterization concept and system proposed.

  10. In-Line Measurement of Water Content in Ethanol Using a PVA-Coated Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Byoung Chul Kim

    2014-01-01

    Full Text Available An in-line device for measuring the water content in ethanol was developed using a polyvinyl alcohol (PVA-coated quartz crystal microbalance. Bio-ethanol is widely used as the replacement of gasoline, and its water content is a key component of its specifications. When the PVA-coated quartz crystal microbalance is contacted with ethanol containing a small amount of water, the water is absorbed into the PVA increasing the load on the microbalance surface to cause a frequency drop. The determination performance of the PVA-coated microbalance is examined by measuring the frequency decreases in ethanol containing 2% to 10% water while the ethanol flows through the measurement device. The measurements indicates that the higher water content is the more the frequency reduction is, though some deviation in the measurements is observed. This indicates that the frequency measurement of an unknown concentration of water in ethanol can be used to determine the water content in ethanol. The PVA coating is examined by microscopy and FTIR (Fourier transform infrared spectroscopy.

  11. In-line measurement of water content in ethanol using a PVA-coated quartz crystal microbalance.

    Science.gov (United States)

    Kim, Byoung Chul; Yamamoto, Takuji; Kim, Young Han

    2014-01-16

    An in-line device for measuring the water content in ethanol was developed using a polyvinyl alcohol (PVA)-coated quartz crystal microbalance. Bio-ethanol is widely used as the replacement of gasoline, and its water content is a key component of its specifications. When the PVA-coated quartz crystal microbalance is contacted with ethanol containing a small amount of water, the water is absorbed into the PVA increasing the load on the microbalance surface to cause a frequency drop. The determination performance of the PVA-coated microbalance is examined by measuring the frequency decreases in ethanol containing 2% to 10% water while the ethanol flows through the measurement device. The measurements indicates that the higher water content is the more the frequency reduction is, though some deviation in the measurements is observed. This indicates that the frequency measurement of an unknown concentration of water in ethanol can be used to determine the water content in ethanol. The PVA coating is examined by microscopy and FTIR (Fourier transform infrared) spectroscopy.

  12. Detection of Glypican-3 Proteins for Hepatocellular Carcinoma Marker Using Wireless-Electrodeless Quartz-Crystal Microbalance

    Science.gov (United States)

    Ogi, Hirotsugu; Omori, Toshinobu; Hatanaka, Kenichi; Hirao, Masahiko; Nishiyama, Masayoshi

    2008-05-01

    Pure shear-wave resonances were excited and detected in 18- and 30-µm-thick electrodeless AT-cut quartz plates in liquids using line antennas contactlessly, achieving high-frequency quartz-crystal microbalances (QCMs). Their fundamental resonance frequencies (85 and 54 MHz) were monitored to study interactions in real time between human glypican-3 and an anti-glypican-3 antibody: glypican-3 is a prospective protein marker for hepatocellular carcinoma. Their affinity was determined by the Langmuir kinetics. This study demonstrates the high ability of the wireless-electrodeless QCM for detection of the protein markers and development of drugs for disorders.

  13. Effects of interface slip and viscoelasticity on the dynamic response of droplet quartz crystal microbalances.

    Science.gov (United States)

    Zhuang, Han; Lu, Pin; Lim, Siak Piang; Lee, Heow Pueh

    2008-10-01

    In the present paper we first present a derivation based on the time-dependent perturbation theory to develop the dynamical equations which can be applied to model the response of a droplet quartz crystal microbalance (QCM) in contact with a single viscoelastic media. Moreover, the no-slip boundary condition across the device-viscoelastic media interface has been relaxed in the present model by using the Ellis-Hayward slip length approach. The model is then used to illustrate the characteristic changes in the frequency and attenuation of the QCM with and without the boundary slippage due to the changes in viscoelasticity as the coated media varies from Newtonian liquid to solid. To complement the theory, experiments have been conducted with microliter droplets of aqueous glycerol solutions and silicone oils with a viscosity in the range of 50 approximately 10,000 cS. The results have confirmed the Newtonian characteristics of the glycerol solutions. In contrast, the acoustic properties of the silicones oils as reflected in the impedance analysis are different from the glycerol solutions. More importantly, it was found that for the silicone oils the frequency steadily increased for several hours and even exceeded the initial value of the unloaded crystal as reflected in the positive frequency shift. Collaborative effects of interfacial slippage and viscoelasticity have been introduced to qualitatively interpret the measured frequency up-shifts for the silicone oils. The present work shows the potential importance of the combined effects of viscoelasticity and interfacial slippage when using the droplet QCM to investigate the rheological behavior of more complex fluids.

  14. Weak antibody-cyclodextrin interactions determined by quartz crystal microbalance and dynamic/static light scattering.

    Science.gov (United States)

    Härtl, Elisabeth; Dixit, Nitin; Besheer, Ahmed; Kalonia, Devendra; Winter, Gerhard

    2013-11-01

    In a quest to elucidate the mechanism by which hydroxypropyl β-cyclodextrin (HPβCD) stabilizes antibodies against shaking stress, two heavily debated hypotheses exist, namely that stabilization is due to HPβCD's surface activity, or due to specific interactions with proteins. In a previous study by Serno et al. (Pharm. Res. 30 (2013) 117), we could refute the first hypothesis by proving that, although HPβCD is slightly surface active, it does not displace the antibody at the air-water interface, and accordingly, its surface activity is not the underlying stabilizing mechanism. In the present study, we investigated the possibility of interactions between HPβCD and monoclonal antibodies as the potential stabilization mechanism using quartz crystal microbalance (QCM) and static as well as dynamic light scattering. In the presence of HPβCD, the adsorption of IgG antibodies in the native state (IgG A) and the unfolded state (IgG A and IgG B) on gold-coated quartz crystals was studied by QCM. Results show that HPβCD causes a reduction in protein adsorption in both the folded and the unfolded states, probably due to an interaction between the protein and the cyclodextrin, leading to a reduced hydrophobicity of the protein and consequently a lower extent of adsorption. These results were supported by investigation of the interaction between the native protein and HPβCD using static and dynamic light scattering experiments, which provide the protein-protein interaction parameters, B22 and kD, respectively. Both B22 and kD showed an increase in magnitude with increasing HPβCD-concentrations, indicating a rise in net repulsive forces between the protein molecules. This is further evidence for the presence of interactions between HPβCD and the studied antibodies, since an association of HPβCD on the protein surface leads to a change in the intermolecular forces between the protein molecules. In conclusion, this study provides evidence that the previously observed

  15. Towards vibrational spectroscopy on surface-attached colloids performed with a quartz crystal microbalance

    Directory of Open Access Journals (Sweden)

    Diethelm Johannsmann

    2016-12-01

    Full Text Available Colloidal spheres attached to a quartz crystal microbalance (QCM produce the so-called “coupled resonances”. They are resonators of their own, characterized by a particle resonance frequency, a resonance bandwidth, and a modal mass. When the frequency of the main resonator comes close to the frequency of the coupled resonance, the bandwidth goes through a maximum. A coupled resonance can be viewed as an absorption line in acoustic shear-wave spectroscopy. The known concepts from spectroscopy apply. This includes the mode assignment problem, selection rules, and the oscillator strength. In this work, the mode assignment problem was addressed with Finite Element calculations. These reveal that a rigid sphere in contact with a QCM displays two modes of vibration, termed “slipping” and “rocking”. In the slipping mode, the sphere rotates about its center; it exerts a tangential force onto the resonator surface at the point of contact. In the rocking mode, the sphere rotates about the point of contact; it exerts a torque onto the substrate. In liquids, both axes of rotation are slightly displaced from their ideal positions. Characteristic for spectroscopy, the two modes do not couple to the mechanical excitation equally well. The degree of coupling is quantified by an oscillator strength. Because the rocking mode mostly exerts a torque (rather than a tangential force, its coupling to the resonator's tangential motion is weak; the oscillator strength consequently is small. Recent experiments on surface-adsorbed colloidal spheres can be explained by the mode of vibration being of the rocking type.

  16. Quartz crystal microbalance and spectroscopy measurements for acid doping in polyaniline films

    Directory of Open Access Journals (Sweden)

    Mohamad M Ayad and Eman A Zaki

    2008-01-01

    Full Text Available We investigated the doping of thin polyaniline (PANI films, prepared by the chemical oxidation of aniline, with different acids. The initial step in the investigation is the preparation of PANI films from aqueous hydrochloric acid solution. This is followed by dedoping with ammonia to obtain a PANI base, which is subsequently doped with strong acids (e.g. hydrochloric, sulfuric, phosphoric and trichloroacetic acids and with a weak acid (acetic acid. The dopant weight fraction (w, which is connected with the gain of mass during the doping of PANI, was determined in situ using a quartz crystal microbalance (QCM. The behavior of PANI upon doping with different anions derived from strong acids indicates that both proton and the anion uptake into the polymer chains occur sharply, rapidly, completely, and reversibly. However the uptake in the case in acetic acid is characterized by slow diffusion. The doping was studied at different concentrations of acetic acid. A second cycle of dedoping–redoping was also performed. The kinetics of the doping reaction is dominated by Fickian diffusion kinetics. The diffusion coefficients (D of the dopant ions into the PANI chains were determined using the QCM and by UV–Vis absorption spectroscopy in the range of (0.076–1.64× 10−15 cm2 s−1. It was found that D in the second cycle of doping is larger than that evaluated from the first cycle of doping for high concentrations of acetic acid. D for the diffusion and for the dopant ion expulsion from the PANI chains was also determined during the redoping process. It was found that D for acetic acid ions in the doping process is larger than that calculated for the dedoping process.

  17. Quartz crystal microbalance study of the kinetics of surface initiated polymerization

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Surface initiated polymerization (SIP) is a valuable tool in synthesizing functional polymer brushes,yet the kinetic understanding of SIP lags behind the development of its application. We apply quartz crystal microbalance (QCM) to address two issues that are not fully addressed yet play a central role in the rational design of functional polymer brushes,namely quantitative determination of the kinetics and the initiator efficiency (IE) of SIP. SIP are monitored online using QCM. Two quantitative frequencythickness (f-T) relations make the direct determination and comparison of the rate of polymerization possible even for different monomers. Based on the bi-termination model,the kinetics of SIP is simply described by two variables,which are related to two polymerization constants,namely a = 1/(kp,s,app-[M][R·]0) and b = kt,s,app/(kp,s,app[M]). Factors that could alter the kinetics of SIP are studied,including (i) the molecular weight of monomers,(ii) the solvent used,(iii) the initial density of the initiator,(iv) the concentration of monomer,[M],and (v) the catalyst system (ratio among the ingredients,metal,ligands,and additives). The dynamic nature of IE is also described by these two variables,IE = a/(a + bt). Instead of the molecular weight and the polydispersity,we suggest that film thickness,the two kinetic parameters (a and b),and the initial density of the initiator and IE be the parameters that characterize ultrathin polymer brushes. Besides the kinetics study of SIP,the reported method has many other applications,for example,in the fast screening of catalyst system for SIP and other polymerization systems.

  18. Arsenic species interactions with a porous carbon electrode as determined with an electrochemical quartz crystal microbalance

    Science.gov (United States)

    Morallón, Emilia; Arias-Pardilla, Joaquín; Calo, J.M.; Cazorla-Amorós, D.

    2009-01-01

    The interactions of arsenic species with platinum and porous carbon electrodes were investigated with an electrochemical quartz crystal microbalance (EQCM) and cyclic voltammetry in alkaline solutions. It is shown that the redox reactions in arsenic-containing solutions, due to arsenic reduction/deposition, oxidation/desorption, and electrocatalyzed oxidation by Pt can be readily distinguished with the EQCM. This approach was used to show that the arsenic redox reactions on the carbon electrode are mechanistically similar to that on the bare Pt electrode. This could not be concluded with just classical cyclic voltammetry alone due to the obfuscation of the faradaic features by the large capacitative effects of the carbon double layer. For the porous carbon electrode, a continual mass loss was always observed during potential cycling, with or without arsenic in the solution. This was attributed to electrogasification of the carbon. The apparent mass loss per cycle was observed to decrease with increasing arsenic concentration due to a net mass increase in adsorbed arsenic per cycle that increased with arsenic concentration, offsetting the carbon mass loss. Additional carbon adsorption sites involved in arsenic species interactions are created during electrogasification, thereby augmenting the net uptake of arsenic per cycle. It is demonstrated that EQCM, and in particular the information given by the behavior of the time derivative of the mass vs. potential, or massogram, is very useful for distinguishing arsenic species interactions with carbon electrodes. It may also prove to be effective for investigating redox/adsorption/desorption behavior of other species in solution with carbon materials as well. PMID:20161369

  19. Arsenic species interactions with a porous carbon electrode as determined with an electrochemical quartz crystal microbalance.

    Science.gov (United States)

    Morallón, Emilia; Arias-Pardilla, Joaquín; Calo, J M; Cazorla-Amorós, D

    2009-06-30

    The interactions of arsenic species with platinum and porous carbon electrodes were investigated with an electrochemical quartz crystal microbalance (EQCM) and cyclic voltammetry in alkaline solutions. It is shown that the redox reactions in arsenic-containing solutions, due to arsenic reduction/deposition, oxidation/desorption, and electrocatalyzed oxidation by Pt can be readily distinguished with the EQCM. This approach was used to show that the arsenic redox reactions on the carbon electrode are mechanistically similar to that on the bare Pt electrode. This could not be concluded with just classical cyclic voltammetry alone due to the obfuscation of the faradaic features by the large capacitative effects of the carbon double layer.For the porous carbon electrode, a continual mass loss was always observed during potential cycling, with or without arsenic in the solution. This was attributed to electrogasification of the carbon. The apparent mass loss per cycle was observed to decrease with increasing arsenic concentration due to a net mass increase in adsorbed arsenic per cycle that increased with arsenic concentration, offsetting the carbon mass loss. Additional carbon adsorption sites involved in arsenic species interactions are created during electrogasification, thereby augmenting the net uptake of arsenic per cycle.It is demonstrated that EQCM, and in particular the information given by the behavior of the time derivative of the mass vs. potential, or massogram, is very useful for distinguishing arsenic species interactions with carbon electrodes. It may also prove to be effective for investigating redox/adsorption/desorption behavior of other species in solution with carbon materials as well.

  20. Lubricity of gold nanocrystals on graphene measured using quartz crystal microbalance

    Science.gov (United States)

    Lodge, M. S.; Tang, C.; Blue, B. T.; Hubbard, W. A.; Martini, A.; Dawson, B. D.; Ishigami, M.

    2016-08-01

    In order to test recently predicted ballistic nanofriction (ultra-low drag and enhanced lubricity) of gold nanocrystals on graphite at high surface speeds, we use the quartz microbalance technique to measure the impact of deposition of gold nanocrystals on graphene. We analyze our measurements of changes in frequency and dissipation induced by nanocrystals using a framework developed for friction of adatoms on various surfaces. We find the lubricity of gold nanocrystals on graphene to be even higher than that predicted for the ballistic nanofriction, confirming the enhanced lubricity predicted at high surface speeds. Our complementary molecular dynamics simulations indicate that such high lubricity is due to the interaction strength between gold nanocrystals and graphene being lower than previously assumed for gold nanocrystals and graphite.

  1. Improved electronic interfaces for AT-cut quartz crystal microbalance sensors under variable damping and parallel capacitance conditions.

    Science.gov (United States)

    Arnau, A; García, J V; Jimenez, Y; Ferrari, V; Ferrari, M

    2008-07-01

    A new configuration of automatic capacitance compensation (ACC) technique based on an oscillatorlike working interface, which permits the tracking of the series resonant frequency and the monitoring of the motional resistance and the parallel capacitance of a thickness-shear mode quartz crystal microbalance sensor, is introduced. The new configuration permits an easier calibration of the system which, in principle, improves the accuracy. Experimental results are reported with 9 and 10 MHz crystals in liquids with different parallel capacitances which demonstrate the effectiveness of the capacitance compensation. Some frequency deviations from the exact series resonant frequency, measured by an impedance analyzer, are explained by the specific nonideal behavior of the circuit components. A tentative approach is proposed to solve this problem that is also common to previous ACC systems.

  2. Fully automatic spray-LBL machine with monitoring the real time growth of multilayer films using Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Shiratori S.

    2013-08-01

    Full Text Available A fully automatic spray-LBL machine with monitoring the real time growth of multilayer films using Quartz Crystal Microbalance (QCM techniques was newly developed. We established fully automatic spray layer-by-layer method by precisely controlling air pressure, solution flow, and spray pattern. The movement pattern towards the substrate during solution spraying allowed fabrication of a nano-scale, flat, thin film over a wide area. Optimization of spray conditions permitted fabrication of the flat film with high and low refractive indexes, and they were piled up alternatively to constitute a one-dimensional photonic crystal with near-infrared reflection characteristics. The heat shield effect of the near-infrared reflective film was also confirmed under natural sunlight. It was demonstrated that the fabrication using the automatic spray-LBL machine and real-time QCM monitoring allows the fabrication of optical quality thin films with precise thickness.

  3. Soybean oil and methyl oleate adsorption onto a steel surface investigated using a quartz crystal microbalance with dissipation monitoring and atomic force microscopy**1

    Science.gov (United States)

    The United States’ 2010 annual production of soybean oil exceeded 8 million metric tons, making a significant vegetable oil surplus available for new uses, particularly as a lubricant. Investigation of soybean oil and methyl oleate adsorption onto steel using a quartz crystal microbalance with diss...

  4. Lipid phase behavior studied with a quartz crystal microbalance: A technique for biophysical studies with applications in screening

    Science.gov (United States)

    Peschel, Astrid; Langhoff, Arne; Uhl, Eva; Dathathreyan, Aruna; Haindl, Susanne; Johannsmann, Diethelm; Reviakine, Ilya

    2016-11-01

    Quartz crystal microbalance (QCM) is emerging as a versatile tool for studying lipid phase behavior. The technique is attractive for fundamental biophysical studies as well applications because of its simplicity, flexibility, and ability to work with very small amounts of material crucial for biomedical studies. Further progress hinges on the understanding of the mechanism, by which a surface-acoustic technique such as QCM, senses lipid phase changes. Here, we use a custom-built instrument with improved sensitivity to investigate phase behavior in solid-supported lipid systems of different geometries (adsorbed liposomes and bilayers). We show that we can detect a model anesthetic (ethanol) through its effect on the lipid phase behavior. Further, through the analysis of the overtone dependence of the phase transition parameters, we show that hydrodynamic effects are important in the case of adsorbed liposomes, and viscoelasticity is significant in supported bilayers, while layer thickness changes make up the strongest contribution in both systems.

  5. Detecting cells on the surface of a silver electrode quartz crystal microbalance using plasma treatment and graft polymerization.

    Science.gov (United States)

    Chou, Hung-Che; Yan, Tsong-Rong; Chen, Ko-Shao

    2009-10-15

    This paper utilizes a silver electrode quartz crystal microbalance (QCM) mass sensor to detect the physiology of cells. This study also investigates the plasma surface modification of silver electrode QCMs through deposition of hexamethyldisilazane (HMDSZ) films as a protection film. To improve the cell growth, this paper also performs post-treatments by surface-grafting acrylic acid (AAc), acrylamide (AAm), and oxygen plasma treatment onto the QCM electrodes. Experimental results indicate that plasma deposition is a useful technique to protect the surface of silver electrodes. This technique extends the unpeeling time of silver electrodes from 1 to 7 days. The hydrophilic silver electrode QCM surface modified by AAm exhibited a better storage time effect than other post-treatments.

  6. Development of a mass sensitive quartz crystal microbalance (QCM)-based DNA biosensor using a 50 MHz electronic oscillator circuit.

    Science.gov (United States)

    García-Martinez, Gonzalo; Bustabad, Enrique Alonso; Perrot, Hubert; Gabrielli, Claude; Bucur, Bogdan; Lazerges, Mathieu; Rose, Daniel; Rodriguez-Pardo, Loreto; Fariña, Jose; Compère, Chantal; Vives, Antonio Arnau

    2011-01-01

    This work deals with the design of a high sensitivity DNA sequence detector using a 50 MHz quartz crystal microbalance (QCM) electronic oscillator circuit. The oscillator circuitry is based on Miller topology, which is able to work in damping media. Calibration and experimental study of frequency noise are carried out, finding that the designed sensor has a resolution of 7.1 ng/cm(2) in dynamic conditions (with circulation of liquid). Then the oscillator is proved as DNA biosensor. Results show that the system is able to detect the presence of complementary target DNAs in a solution with high selectivity and sensitivity. DNA target concentrations higher of 50 ng/mL can be detected.

  7. Development of a Mass Sensitive Quartz Crystal Microbalance (QCM-Based DNA Biosensor Using a 50 MHz Electronic Oscillator Circuit

    Directory of Open Access Journals (Sweden)

    Claude Gabrielli

    2011-08-01

    Full Text Available This work deals with the design of a high sensitivity DNA sequence detector using a 50 MHz quartz crystal microbalance (QCM electronic oscillator circuit. The oscillator circuitry is based on Miller topology, which is able to work in damping media. Calibration and experimental study of frequency noise are carried out, finding that the designed sensor has a resolution of 7.1 ng/cm2 in dynamic conditions (with circulation of liquid. Then the oscillator is proved as DNA biosensor. Results show that the system is able to detect the presence of complementary target DNAs in a solution with high selectivity and sensitivity. DNA target concentrations higher of 50 ng/mL can be detected.

  8. Determination of isoelectric points and the role of pH for common quartz crystal microbalance sensors.

    Science.gov (United States)

    Cuddy, Michael F; Poda, Aimee R; Brantley, Lauren N

    2013-05-01

    Isoelectric points (IEPs) were determined by the method of contact angle titration for five common quartz crystal microbalance (QCM) sensors. The isoelectric points range from mildly basic in the case of Al2O3 sensors (IEP = 8.7) to moderately acidic for Au (5.2) and SiO2 (3.9), to acidic for Ag (3.2) and Ti (2.9). In general, the values reported here are indicative of inherent surface oxides. A demonstration of the effect of the surface isoelectric point on the packing efficiency of thin mucin films is provided for gold and silica QCM sensors. It is determined that mucin layers on both substrates achieve a maximum and equal layer density of ∼3500 kg/m(3) at the corresponding IEP of either QCM sensor. This implies that mucin film packing is dependent upon short-range electrostatic interactions at the sensor surface.

  9. Determination of thermodynamic parameters for enolization reaction of malonic and metylmalonic acids by using quartz crystal microbalance

    Directory of Open Access Journals (Sweden)

    Minoru Yoshimoto

    2016-06-01

    Full Text Available We investigated the process of a bromination reaction of malonic acid and methylmalonic acid in the Belousov-Zhabotinsky reaction by using a quartz crystal microbalance (QCM. The process involves an enolization reaction as a rate-determining step. We found that, in the step, the variation of Br2 concentration induced an exactly quantitative shift of a resonant frequency of the QCM, based on the change of the surface mass on the QCM and the solution viscosity and density. This new finding enabled us to estimate the reaction rate constants and the thermodynamic parameters of the enolization reaction due to a QCM measurement. The values measured by the QCM were in good agreement with those measured by a UV-spectrophotometer. As a result, we succeeded to develop a new measurement method of a nonlinear chemical reaction.

  10. Sugar nanowires based on cyclodextrin on quartz crystal microbalance for gas sensing with ultra-high sensitivity

    Science.gov (United States)

    Asano, Atsushi; Maeyoshi, Yuta; Watanabe, Shogo; Saeki, Akinori; Sugimoto, Masaki; Yoshikawa, Masahito; Nanto, Hidehito; Tsukuda, Satoshi; Tanaka, Shun-Ichiro; Seki, Shu

    2013-03-01

    Cyclodextrins (CDs), hosting selectively a wide range of guest molecules in their hydrophobic cavity, were directly fabricated into 1-dimensional nanostructures with extremely wide surface area by single particle nanofabrication technique in the present paper. The copolymers of acrylamide and mono(6-allyl)-β-CD were synthesized, and the crosslinking reaction of the polymer alloys with poly(4-bromostyrene) (PBrS) in SPNT gave nanowires on the quarts substrate with high number density of 5×109 cm-2. Quartz crystal microbalance (QCM) measurement suggested 320 fold high sensitivity for formic acid vapor adsorption in the nanowire fabricated surfaces compared with that in the thin solid film of PBrS, due to the incorporation of CD units and extremely wide surface area of the nanowires.

  11. Equilibrium Water Contents of Cellulose Films Determined via Solvent Exchange and Quartz Crystal Microbalance with Dissipation Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Kittle, Joshua D; Du, Xiaosong; Jiang, Feng; Qian, Chen; Heinze, Thomas; Roman, Maren; Esker, Alan R

    2011-08-08

    Model cellulose surfaces have attracted increasing attention for studying interactions with cell wall matrix polymers and as substrates for enzymatic degradation studies. Quartz crystal microbalance with dissipation monitoring (QCM-D) solvent exchange studies showed that the water content of regenerated cellulose (RC) films was proportional to the film thickness (d) and was consistent with about five water molecules per anhydroglucose unit. Sulfated nanocrystalline cellulose (SNC) and desulfated nanocrystalline cellulose (DNC) films had comparable water contents and contained about five times more water than RC films. A cellulase mixture served as a probe for studies of substrate accessibility and degradation. Cellulase adsorption onto RC films was independent of d, whereas degradation times increased with d. However, adsorption onto SNC and DNC films increased with d, whereas cellulase degradation times for DNC films were independent of studied d. Enhanced access to guest molecules for SNC and DNC films revealed they are more porous than RC films.

  12. Equilibrium water contents of cellulose films determined via solvent exchange and quartz crystal microbalance with dissipation monitoring.

    Science.gov (United States)

    Kittle, Joshua D; Du, Xiaosong; Jiang, Feng; Qian, Chen; Heinze, Thomas; Roman, Maren; Esker, Alan R

    2011-08-08

    Model cellulose surfaces have attracted increasing attention for studying interactions with cell wall matrix polymers and as substrates for enzymatic degradation studies. Quartz crystal microbalance with dissipation monitoring (QCM-D) solvent exchange studies showed that the water content of regenerated cellulose (RC) films was proportional to the film thickness (d) and was consistent with about five water molecules per anhydroglucose unit. Sulfated nanocrystalline cellulose (SNC) and desulfated nanocrystalline cellulose (DNC) films had comparable water contents and contained about five times more water than RC films. A cellulase mixture served as a probe for studies of substrate accessibility and degradation. Cellulase adsorption onto RC films was independent of d, whereas degradation times increased with d. However, adsorption onto SNC and DNC films increased with d, whereas cellulase degradation times for DNC films were independent of studied d. Enhanced access to guest molecules for SNC and DNC films revealed they are more porous than RC films.

  13. In-Line Measurement of Water Contents in Ethanol Using a Zeolite-Coated Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Byoung Chul Kim

    2015-10-01

    Full Text Available A quartz crystal microbalance (QCM was utilized to measure the water content in ethanol. For the improvement of measurement sensitivity, the QCM was modified by applying zeolite particles on the surface with poly(methyl methacrylate (PMMA binder. The measurement performance was examined with ethanol of 1% to 5% water content in circulation. The experimental results showed that the frequency drop of the QCM was related with the water content though there was some deviation. The sensitivity of the zeolite-coated QCM was sufficient to be implemented in water content determination, and a higher ratio of silicon to aluminum in the molecular structure of the zeolite gave better performance. The coated surface was inspected by microscopy to show the distribution of zeolite particles and PMMA spread.

  14. Effective antibodies immobilization and functionalized nanoparticles in a quartz-crystal microbalance-based immunosensor for the detection of parathion

    Science.gov (United States)

    Della Ventura, Bartolomeo; Iannaccone, Marco; Funari, Riccardo; Pica Ciamarra, Massimo; Altucci, Carlo; Capparelli, Rosanna; Roperto, Sante; Velotta, Raffaele

    2017-01-01

    Background Biosensor-based detection provides a rapid and low-cost alternative to conventional analytical methods for revealing the presence of the contaminants in water as well as solid matrices. Although important to be detected, small analytes (few hundreds of Daltons) are an issue in biosensing since the signal they induce in the transducer, and specifically in a Quartz-Crystal Microbalance, is undetectable. A pesticide like parathion (M = 292 Da) is a typical example of contaminant for which a signal amplification procedure is desirable. Methods/Findings The ballasting of the analyte by gold nanoparticles has been already applied to heavy target as proteins or bacteria to improve the limit of detection. In this paper, we extend the application of such a method to small analytes by showing that once the working surface of a Quartz-Crystal Microbalance (QCM) has been properly functionalized, a limit of detection lower than 1 ppb is reached for parathion. The effective surface functionalization is achieved by immobilizing antibodies upright oriented on the QCM gold surface by a simple photochemical technique (Photonic Immobilization Technique, PIT) based on the UV irradiation of the antibodies, whereas a simple protocol provided by the manufacturer is applied to functionalize the gold nanoparticles. Thus, in a non-competitive approach, the small analyte is made detectable by weighing it down through a “sandwich protocol” with a second antibody tethered to heavy gold nanoparticles. The immunosensor has been proved to be effective against the parathion while showing no cross reaction when a mixture of compounds very similar to parathion is analyzed. Conclusion/Significance The immunosensor described in this paper can be easily applied to any small molecule for which polyclonal antibodies are available since both the functionalization procedure of the QCM probe surface and gold nanoparticle can be applied to any IgG, thereby making our device of general

  15. The use of quartz crystal microbalance with dissipation (QCM-D for studying nanoparticle-induced platelet aggregation

    Directory of Open Access Journals (Sweden)

    Santos-Martinez MJ

    2012-01-01

    Full Text Available Maria Jose Santos-Martinez1–3, Iwona Inkielewicz-Stepniak1,4, Carlos Medina1, Kamil Rahme5,6, Deirdre M D'Arcy1, Daniel Fox3, Justin D Holmes3,5, Hongzhou Zhang3, Marek Witold Radomski3,51School of Pharmacy and Pharmaceutical Sciences, 2School of Medicine, 3Center for Research on Adaptive Nanostructures and Nanodevices, Trinity College Dublin, Dublin, Ireland; 4Department of Medicinal Chemistry, Medical University of Gdansk, Gdansk, Poland; 5Materials and Supercritical Fluids Group, Department of Chemistry and the Tyndall National Institute, University College Cork, Cork, Ireland; 6Department of Sciences, Faculty of Natural and Applied Science, Notre Dame University, Zouk Mosbeh, LebanonAbstract: Interactions between blood platelets and nanoparticles have both pharmacological and toxicological significance and may lead to platelet activation and aggregation. Platelet aggregation is usually studied using light aggregometer that neither mimics the conditions found in human microvasculature nor detects microaggregates. A new method for the measurement of platelet microaggregation under flow conditions using a commercially available quartz crystal microbalance with dissipation (QCM-D has recently been developed. The aim of the current study was to investigate if QCM-D could be used for the measurement of nanoparticle-platelet interactions. Silica, polystyrene, and gold nanoparticles were tested. The interactions were also studied using light aggregometry and flow cytometry, which measured surface abundance of platelet receptors. Platelet activation was imaged using phase contrast and scanning helium ion microscopy. QCM-D was able to measure nanoparticle-induced platelet microaggregation for all nanoparticles tested at concentrations that were undetectable by light aggregometry and flow cytometry. Microaggregates were measured by changes in frequency and dissipation, and the presence of platelets on the sensor surface was confirmed and imaged by

  16. Pharmacological characterization of nanoparticle-induced platelet microaggregation using quartz crystal microbalance with dissipation: comparison with light aggregometry

    Science.gov (United States)

    Santos-Martinez, Maria J; Tomaszewski, Krzysztof A; Medina, Carlos; Bazou, Despina; Gilmer, John F; Radomski, Marek W

    2015-01-01

    Background Engineered nanoparticles (NPs) can induce platelet activation and aggregation, but the mechanisms underlying these interactions are not well understood. This could be due in part to use of devices that study platelet function under quasi-static conditions with low sensitivity to measure platelet microaggregation. Therefore, in this study we investigated the pharmacological pathways and regulators of NP-induced platelet microaggregation under flow conditions at nanoscale using quartz crystal microbalance with dissipation (QCM-D) and compared the data thus obtained with those generated by light aggregometry. Methods Blood was collected from healthy volunteers, and platelet-rich plasma was obtained. Thrombin receptor-activating peptide, a potent stimulator of platelet function, and pharmacological inhibitors were used to modulate platelet microaggregation in the presence/absence of silica (10 nm and 50 nm) and polystyrene (23 nm) NPs. Light aggregometry was used to study platelet aggregation in macroscale. Optical, immunofluorescence, and scanning electron microscopy were also used to visualize platelet aggregates. Results Platelet microaggregation was enhanced by thrombin receptor-activating peptide, whereas prostacyclin, nitric oxide donors, acetylsalicylic acid, and phenanthroline, but not adenosine diphosphate (ADP) blockers, were able to inhibit platelet microaggregation. NPs caused platelet microaggregation, an effect not detectable by light aggregometry. NP-induced microaggregation was attenuated by platelet inhibitors. Conclusion NP-induced platelet microaggregation appears to involve classical proaggregatory pathways (thromboxane A2-mediated and matrix metalloproteinase-2-mediated) and can be regulated by endogenous (prostacyclin) and pharmacological (acetylsalicylic acid, phenanthroline, and nitric oxide donors) inhibitors of platelet function. Quartz crystal microbalance with dissipation, but not light aggregometry, is an appropriate method for

  17. Preparation of new molecularly imprinted quartz crystal microbalance hybride sensor system for 8-hydroxy-2'-deoxyguanosine determination.

    Science.gov (United States)

    Say, Ridvan; Gültekin, Aytaç; Ozcan, Ayça Atilir; Denizli, Adil; Ersöz, Arzu

    2009-04-27

    The routine measurement of 8-hydroxy-2'-deoxyguanosine (8-OHdG) in biological samples is a difficult analytical problem due to the low levels of the analyte and complex matrix. A new 8-OHdG imprinted quartz crystal microbalance (QCM) sensor has been developed for selective determination of 8-OHdG in serum samples. To fulfil the desired results, we have used methacryloyl aminoantipyrine-Fe(III) [MAAP-Fe(III)] and methacryloyl histidine-Pt(II) [MAH-Pt(II)] as metal-chelating monomers via double metal coordination-chelation interactions for the preparation of additional selective molecular imprinted polymers (MIP). The study includes the measurement of binding interaction of 8-OHdG imprinted quartz crystal microbalance (QCM) sensor, selectivity experiments and analytical performance of QCM chip. The obtained results have showed that the application of double metal-chelate monomer systems has been more effective than single metal-chelate monomer systems. In this study, the detection limit and the linear working range were found to be 0.0075 and 0.0100-3.5 microM, respectively. The affinity constant (K(affinity)) was found to be 1.54x10(5) M(-1) for 8-OHdG using MAH-Pt-8-OHdG-MAAP-Fe based thin film. Also, selectivity of prepared QCM sensor was found as being very high in the presence of competitive species. At the last step of this procedure, 8-OHdG level in blood serum which belongs to a intestinal cancer patient was determined by the prepared QCM sensor.

  18. Detection of NH{sub 3} by quartz crystal microbalance coated with TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Georgieva, V; Spassov, L; Gadjanova, V [Georgi Nadjakov Institute of Solid State Physics, Bulgarian Academy of Sciences, 72 Tzarigradsko Chaussee, 1784 Sofia (Bulgaria); Donkov, N; Petkov, P [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tzarigradsko Chausee, 1784 Sofia (Bulgaria)], E-mail: nikolaidd@abv.bg

    2008-05-01

    A quartz resonator with a thin TiO{sub 2} film is investigated in view of possible applications as a sensor for detecting the presence of ammonia in the ambient. A study of the sorption properties of thin TiO{sub 2} films to NH{sub 3} vapors is also presented. The films are deposited using electron beam evaporation. In order to determine the sorption ability of TiO{sub 2} to NH{sub 3}, a quartz crystal microbalance (QCM) with a thin TiO{sub 2} film is used, the latter serving as a receptor for the NH{sub 3} gas. The AT-cut 16-MHz quartz resonator allows conversion of the additional mass load that occurs as a result of sorption into a frequency shift. The experiments are carried out by measuring the QCM resonant frequency shift due to the absorption of vapors from an aqueous solution of NH{sub 3} with different concentration ranging from 100 to 1000 ppm. The experimental results obtained indicate that the variation of the resonant frequency is a function of the ammonia concentration. This demonstrates that a QCM covered with a thin TiO{sub 2} layer is sensitive to ammonia vapors at room temperature and is capable of detecting NH{sub 3} concentrations in the range investigated (100-1000 ppm)

  19. Humidity scanning quartz crystal microbalance with dissipation monitoring setup for determination of sorption-desorption isotherms and rheological changes

    Energy Technology Data Exchange (ETDEWEB)

    Björklund, Sebastian, E-mail: sebastianbjorklund@gmail.com; Kocherbitov, Vitaly [Department of Biomedical Science, Faculty of Health and Society, Malmö University, Malmö (Sweden); Biofilms—Research Center for Biointerfaces, Malmö University, Malmö (Sweden)

    2015-05-15

    A new method to determine water sorption-desorption isotherms with high resolution in the complete range of water activities (relative humidities) is presented. The method is based on quartz crystal microbalance with dissipation monitoring (QCM-D). The QCM-D is equipped with a humidity module in which the sample film is kept in air with controlled humidity. The experimental setup allows for continuous scanning of the relative humidity from either dry to humid conditions or vice versa. The amount of water sorbed or desorbed from the sample is determined from the resonance frequencies of the coated quartz sensor, via analysis of the overtone dependence. In addition, the method allows for characterization of hydration induced changes of the rheological properties from the dissipation data, which is closely connected to the viscoelasticity of the film. The accuracy of the humidity scanning setup is confirmed in control experiments. Sorption-desorption isotherms of pig gastric mucin and lysozyme, obtained by the new method, show good agreement with previous results. Finally, we show that the deposition technique used to coat the quartz sensor influences the QCM-D data and how this issue can be used to obtain further information on the effect of hydration. In particular, we demonstrate that spin-coating represents an attractive alternative to obtain sorption-desorption isotherms, while drop-coating provides additional information on changes of the rheological properties during hydration.

  20. An Electrochemical Quartz Crystal Microbalance Multisensor System Based on Phthalocyanine Nanostructured Films: Discrimination of Musts

    Directory of Open Access Journals (Sweden)

    Celia Garcia-Hernandez

    2015-11-01

    Full Text Available An array of electrochemical quartz crystal electrodes (EQCM modified with nanostructured films based on phthalocyanines was developed and used to discriminate musts prepared from different varieties of grapes. Nanostructured films of iron, nickel and copper phthalocyanines were deposited on Pt/quartz crystals through the Layer by Layer technique by alternating layers of the corresponding phthalocyanine and poly-allylamine hydrochloride. Simultaneous electrochemical and mass measurements were used to study the mass changes accompanying the oxidation of electroactive species present in must samples obtained from six Spanish varieties of grapes (Juan García, Prieto Picudo, Mencía Regadío, Cabernet Sauvignon, Garnacha and Tempranillo. The mass and voltammetric outputs were processed using three-way models. Parallel Factor Analysis (PARAFAC was successfully used to discriminate the must samples according to their variety. Multi-way partial least squares (N-PLS evidenced the correlations existing between the voltammetric data and the polyphenolic content measured by chemical methods. Similarly, N-PLS showed a correlation between mass outputs and parameters related to the sugar content. These results demonstrated that electronic tongues based on arrays of EQCM sensors can offer advantages over arrays of mass or voltammetric sensors used separately.

  1. Characterization of Self-assembled Monolayers on Gold Electrode Using Electrochemical Quartz Crystal Microbalance

    Institute of Scientific and Technical Information of China (English)

    Yonggui Dong

    2006-01-01

    The electrochemical quartz crystal microbatance (EQCM) is used to investigate the characteristics of the thiolated self-assembled monolayer(SAM) on gold surface. A 5MHz QCM element serves as both the mass-sensitive sensor and the working electrode of the electrochemical system. The 6-mecapto-1-hexanol and and the 16-mer oligonucleotide with a mercaptohexyl group at the 5'-phosphate end are utilized to form the SAM on the gold electrode. The frequency response of the QCM during cyclic voltammetry (CV) scanning and chronoamperometry are recorded together with the electrochemical current. The experimental results indicates that the frequency response is more sensitive to the surface coverage. Therefore, the response of the EQCM reveals more details of the SAM on gold electrode. It is especially useful for analysing the immobilization quality, such as probe orientation and coverage, of the SAM.

  2. Small organic molecules detection based on aptamer-modified gold nanoparticles-enhanced quartz crystal microbalance with dissipation biosensor.

    Science.gov (United States)

    Zheng, Bin; Cheng, Sheng; Liu, Wei; Lam, Michael Hon-Wah; Liang, Haojun

    2013-07-15

    Small molecules are difficult to detect by the conventional quartz crystal microbalance with dissipation (QCM-D) technique directly because the changes in frequency resulting from the binding processes of small biomolecules are often small. In the current study, an aptamer-based gold nanoparticles (AuNPs)-enhanced sensing strategy for detection of small molecules was developed. The QCM crystal was first modified with a layer of thiolated linker DNA, which can be partly base-paired with the detection part containing the adenosine aptamer sequence. In the presence of adenosine, the aptamer bound with adenosine and folded to the complex structure, which precluded the reporter part carrying AuNPs to combine with the random coiled detection part. Therefore, the lower the concentration of adenosine, the more AuNPs combined to the crystal. The resulting aptasensor showed a linear response to the increase of the adenosine concentration in the range of 0-2 μM with a linear correlation of r=0.99148 and a detection limit of 65 nM. Moreover, the aptasensor exhibited several excellent characteristics such as high sensitivity, selectivity, good stability, and reproducibility.

  3. Pathogen detection in complex samples by quartz crystal microbalance sensor coupled to aptamer functionalized core-shell type magnetic separation.

    Science.gov (United States)

    Ozalp, Veli C; Bayramoglu, Gulay; Erdem, Zehra; Arica, M Yakup

    2015-01-01

    A quartz crystal microbalance sensor (QCM) was developed for sensitive and specific detection of Salmonella enterica serovar typhimurium cells in food samples by integrating a magnetic bead purification system. Although many sensor formats based on bioaffinity agents have been developed for sensitive and specific detection of bacterial cells, the development of robust sensor applications for food samples remained a challenging issue. A viable strategy would be to integrate QCM to a pre-purification system. Here, we report a novel and sensitive high throughput strategy which combines an aptamer-based magnetic separation system for rapid enrichment of target pathogens and a QCM analysis for specific and real-time monitoring. As a proof-of-concept study, the integration of Salmonella binding aptamer immobilized magnetic beads to the aptamer-based QCM system was reported in order to develop a method for selective detection of Salmonella. Since our magnetic separation system can efficiently capture cells in a relatively short processing time (less than 10 min), feeding captured bacteria to a QCM flow cell system showed specific detection of Salmonella cells at 100 CFU mL(-1) from model food sample (i.e., milk). Subsequent treatment of the QCM crystal surface with NaOH solution regenerated the aptamer-sensor allowing each crystal to be used several times.

  4. Superior environment resistance of quartz crystal microbalance with anatase TiO{sub 2}/ZnO nanorod composite films

    Energy Technology Data Exchange (ETDEWEB)

    Qiang, Wei, E-mail: weiqiang.tju@163.com [Tianjin Key Laboratory of Composite and Functional Materials, School of Materials Science and Engineering, Tianjin University, 92 Weijin Road, Tianjin (China); Wei, Li; Shaodan, Wang [Tianjin Key Laboratory of Composite and Functional Materials, School of Materials Science and Engineering, Tianjin University, 92 Weijin Road, Tianjin (China); Yu, Bai [Beijing Institute of Spacecrafts Environment Engineering, Beijing 100094 (China)

    2015-08-30

    Graphical abstract: ZnO nanorod array being prepared by an in situ method on the QCM coated with Au film via hydrothermal process and surface modification with coated TiO{sub 2} by sol–gel methods to form a superhydrophobic TiO{sub 2}/ZnO composite film the anatase TiO{sub 2}/ZnO nanorod composite film with a sharp, pencil-like structure exhibiting excellent superhydrophobicity (water contact angle of 155°), non-sticking water properties, and an autonomous cleaning property under UV irradiation. The anatase TiO{sub 2}/ZnO nanorod composite film facilitates the precise measurement and extended lifetime of the QCM for the detection of organic gas molecules. - Highlights: • This work combines, for the first time, the advantage of the TiO{sub 2}/ZnO composite film on photocatalysis and reversible super-hydrophobic and super-hydrophilic transition, and puts forward a solution to satisfy weatherability of quartz crystal microbalance in long-term application. • The anatase TiO{sub 2}/ZnO nanorod composite film with pencil structure exhibit excellent super-hydrophobicity (water contact angle can reach 155°), no-sticking water properties and self-cleaning property under UV irradiation. • The photocatalysis and reversible super-hydrophobic and super-hydrophilic transition of the TiO{sub 2}/ZnO nanorod composite film is stable in long-term application. - Abstract: The precise measurement of quartz crystal microbalance (QCM) in the detection and weighing of organic gas molecules is achieved due to excellent superhydrophobicity of a deposited film composite. Photocatalysis is utilized as a method for the self-cleaning of organic molecules on the QCM for extended long-term stability in the precision of the instrument. In this paper, ZnO nanorod array is prepared via in situ methods on the QCM coated with Au film via hydrothermal process. Subsequently, a TiO{sub 2}/ZnO composite film is synthesized by surface modification with TiO{sub 2} via sol–gel methods. Results

  5. Long Memory from Sauerbrey Equation: A Case in Coated Quartz Crystal Microbalance in terms of Ammonia

    Directory of Open Access Journals (Sweden)

    Xiaohua Wang

    2011-01-01

    Full Text Available The Sauerbrey equation is a useful empirical model in material science to represent the dynamics of frequency change denoted by Δf in an area, denoted by A, of the electrode in terms of the increment of the mass, which is denoted by Δm, loaded on the surface of the crystal under a certain resonant frequency f0. For the purpose of studying Δf from the point of view of time series, we first propose two types of the modified representations of the Sauerbrey equation by taking time as an argument to represent Δf as a function expressed by x(t,f0,A,Δm, where t is time. Usually, Δf is studied experimentally for the performance evaluation of the tested quartz used in ammonia sensors. Its properties in time series, however, are rarely reported. This paper presents the fractal properties of Δf. We will show that Δf is long range dependent (LRD. Consequently, it is heavy tailed according to the Taqqu's theorem. The Hurst parameter (H of Δf approaches one, implying its strong long memory, providing a new explanation of the repeatability of the experiments and novel point of view of the dynamics of Δf relating to the Sauerbrey equation in material science.

  6. Electrochemical quartz crystal microbalance study on the two-electrode-system cyclic voltammetric behavior of Prussian blue films

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A two-channel electrochemical quartz crystal microbalance (EQCM) was used to investigate the cyclic voltammetric behavior of two Prussian blue (PB) film-modified Au electrodes in a two-electrode con-figuration in aqueous solution. The redox peaks observed in the two-electrode cyclic voltammogram (CV) are assigned to the intrinsic redox transitions among the Everitt’s salt, PB, and Prussian yellow for the film itself, the redox process of the Au substrate and the redox process of small-quantity ferri-/ferrocyanide impurities entrapped in the PB film, as also supported by ultraviolet-visible (UV-Vis) spectroelectrochemical data. The profile of the two-electrode solid-state CV for the PB powder sand-wiched between two gold-coated indium-tin oxide (ITO) electrodes is similar to that for two PB-modified Au electrodes in aqueous solution, implying similar origins for the corresponding redox peaks. The two-channel EQCM method is expected to become a highly effective technique for the studies of the two-electrode electrochemical behaviors of many other species/materials.

  7. A novel dendritic surfactant for enhanced microcystin-LR detection by double amplification in a quartz crystal microbalance biosensor.

    Science.gov (United States)

    Xia, Yuetong; Zhang, Jianping; Jiang, Long

    2011-08-01

    Enhanced sensitivity for the hepatotoxin microcystin-LR (MC-LR) was achieved in a quartz crystal microbalance (QCM) system via double amplification. For primary amplification, an innovative interface on the QCM was obtained as a matrix by the vesicle layer formed by our synthetic dendritic surfactant, bis (amidoethyl-carbamoylethyl) octadecylamine (C18N3). The vesicle matrix was then functionalised by an optimised concentration of monoclonal antibodies against MC-LR (anti-MC-LR) to detect the analyte. The results showed that a detection limit of 100 ng/mL was achieved by primary amplification. To achieve higher sensitivity, secondary amplification was implemented with anti-MC-LR gold nanoparticle (AuNPs) conjugates as probes, which lowered the detection limit for MC-LR to 1 ng/mL (the maximum concentration recommended by the World Health Organization [WHO] in drinking water for humans). The QCM immunosensor reported here has advantages such as high sensitivity, portability, simplicity, and cost-effectiveness for MC-LR detection. It would be uniquely superior compared with current MC-LR detection techniques for on-the-spot water detection. Furthermore, the methodology described here is also potentially significant in many fields for the routine monitoring of environmental and food safety.

  8. Adsorption Analysis of Lactoferrin to Titanium, Stainless Steel, Zirconia, and Polymethyl Methacrylate Using the Quartz Crystal Microbalance Method

    Directory of Open Access Journals (Sweden)

    Eiji Yoshida

    2016-01-01

    Full Text Available It is postulated that biofilm formation in the oral cavity causes some oral diseases. Lactoferrin is an antibacterial protein in saliva and an important defense factor against biofilm development. We analyzed the adsorbed amount of lactoferrin and the dissociation constant (Kd of lactoferrin to the surface of different dental materials using an equilibrium analysis technique in a 27 MHz quartz crystal microbalance (QCM measurement. Four different materials, titanium (Ti, stainless steel (SUS, zirconia (ZrO2 and polymethyl methacrylate (PMMA, were evaluated. These materials were coated onto QCM sensors and the surfaces characterized by atomic force microscopic observation, measurements of surface roughness, contact angles of water, and zeta potential. QCM measurements revealed that Ti and SUS showed a greater amount of lactoferrin adsorption than ZrO2 and PMMA. Surface roughness and zeta potential influenced the lactoferrin adsorption. On the contrary, the Kd value analysis indicated that the adsorbed lactoferrin bound less tightly to the Ti and SUS surfaces than to the ZrO2 and PMMA surfaces. The hydrophobic interaction between lactoferrin and ZrO2 and PMMA is presumed to participate in better binding of lactoferrin to ZrO2 and PMMA surfaces. It was revealed that lactoferrin adsorption behavior was influenced by the characteristics of the material surface.

  9. Biomolecular interactions and tools for their recognition: focus on the quartz crystal microbalance and its diverse surface chemistries and applications.

    Science.gov (United States)

    Cheng, Cathy I; Chang, Yi-Pin; Chu, Yen-Ho

    2012-03-07

    Interactions between molecules are ubiquitous and occur in our bodies, the food we eat, the air we breathe, and myriad additional contexts. Although numerous tools are available for the recognition of biomolecular interactions, such tools are often limited in their sensitivity, expensive, and difficult to modify for various uses. In contrast, the quartz crystal microbalance (QCM) has sub-nanogram detection capabilities, is label-free, is inexpensive to create, and can be readily modified with a number of diverse surface chemistries to detect and characterize diverse interactions. To maximize the versatility of the QCM, scientists need to know available methods by which QCM surfaces can be modified. Therefore, in addition to summarizing the various tools currently used for biomolecular recognition, explicating the fundamental principles of the QCM as a tool for biomolecular recognition, and comparing the QCM with other acoustic sensors, we systematically review the numerous types of surface chemistries-including hydrophobic bonds, ionic bonds, hydrogen bonds, self-assembled monolayers, plasma-polymerized films, photochemistry, and sensing ionic liquids-used to functionalize QCMs for various purposes. We also review the QCM's diverse applications, which include the detection of gaseous species, detection of carbohydrates, detection of nucleic acids, detection of non-enzymatic proteins, characterization of enzymatic activity, detection of antigens and antibodies, detection of cells, and detection of drugs. Finally, we discuss the ultimate goals of and potential barriers to the development of future QCMs.

  10. Colloidal Stability and Magnetic Field-Induced Ordering of Magnetorheological Fluids Studied with a Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Jaime Rodriguez-López

    2015-12-01

    Full Text Available This work proposes the use of quartz crystal microbalances (QCMs as a method to analyze and characterize magnetorheological (MR fluids. QCM devices are sensitive to changes in mass, surface interactions, and viscoelastic properties of the medium contacting its surface. These features make the QCM suitable to study MR fluids and their response to variable environmental conditions. MR fluids change their structure and viscoelastic properties under the action of an external magnetic field, this change being determined by the particle volume fraction, the magnetic field strength, and the presence of thixotropic agents among other factors. In this work, the measurement of the resonance parameters (resonance frequency and dissipation factor of a QCM are used to analyze the behavior of MR fluids in static conditions (that is, in the absence of external mechanical stresses. The influence of sedimentation under gravity and the application of magnetic fields on the shifts of resonance frequency and dissipation factor were measured and discussed in the frame of the coupled resonance produced by particles touching the QCM surface. Furthermore, the MR-fluid/QCM system has a great potential for the study of high-frequency contact mechanics because the translational and rotational stiffness of the link between the surface and the particles can be tuned by the magnetic field.

  11. Real-time monitoring of peptic and tryptic digestions of bovine {beta}-casein using quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Huenerbein, Andreas [Institute of Pharmaceutics and Biopharmaceutics, Martin Luther University Halle-Wittenberg, Wolfgang-Langenbeck-Str. 4, 06120 Halle (Saale) (Germany)]. E-mail: andreas.huenerbein@pharmazie.uni-halle.de; Schmelzer, Christian E.H. [Institute of Pharmaceutics and Biopharmaceutics, Martin Luther University Halle-Wittenberg, Wolfgang-Langenbeck-Str. 4, 06120 Halle (Saale) (Germany); Neubert, Reinhard H.H. [Institute of Pharmaceutics and Biopharmaceutics, Martin Luther University Halle-Wittenberg, Wolfgang-Langenbeck-Str. 4, 06120 Halle (Saale) (Germany)

    2007-02-12

    In this study peptic and tryptic digestions of bovine {beta}-casein were investigated using quartz crystal microbalance (QCM). {beta}-Casein, which was used as a model protein, was immobilized on the surface of the QCM sensor where its degradation caused shifts in the resonant frequency. Atomic force microscopy was applied for the characterization of the protein layer. Different pH-values for peptic or tryptic digestions were chosen to visualize their effect on enzyme activity. Lower frequency shifts were observed at pH-values deviating from those at the maximum enzyme activity. In the case of the peptic digestion the frequency shift at pH 4 was more than 10 times smaller than those at pH 2. The frequency shifts for tryptic digestions at pH 5.4 and pH 6.4 were about two thirds compared to that obtained for the digestion at pH 7.4. The identification of peptides using MALDI-ToF mass spectrometry was used for verification of the proteolyses of the immobilized protein. Furthermore, it was shown that the QCM technique allows close observation of the effect of different pH-values on the immobilized casein layer. All in all, QCM facilitates the monitoring of the progress of enzymatic reactions in real-time.

  12. Peptide-membrane interactions of arginine-tryptophan peptides probed using quartz crystal microbalance with dissipation monitoring.

    Science.gov (United States)

    Rydberg, Hanna A; Kunze, Angelika; Carlsson, Nils; Altgärde, Noomi; Svedhem, Sofia; Nordén, Bengt

    2014-07-01

    Membrane-active peptides include peptides that can cross cellular membranes and deliver macromolecular cargo as well as peptides that inhibit bacterial growth. Some of these peptides can act as both transporters and antibacterial agents. It is desirable to combine the knowledge from these two different fields of membrane-active peptides into design of new peptides with tailored actions, as transporters of cargo or as antibacterial substances, targeting specific membranes. We have previously shown that the position of the amino acid tryptophan in the peptide sequence of three arginine-tryptophan peptides affects their uptake and intracellular localization in live mammalian cells, as well as their ability to inhibit bacterial growth. Here, we use quartz crystal microbalance with dissipation monitoring to assess the induced changes caused by binding of the three peptides to supported model membranes composed of POPC, POPC/POPG, POPC/POPG/cholesterol or POPC/lactosyl PE. Our results indicate that the tryptophan position in the peptide sequence affects the way these peptides interact with the different model membranes and that the presence of cholesterol in particular seems to affect the membrane interaction of the peptide with an even distribution of tryptophans in the peptide sequence. These results give mechanistic insight into the function of these peptides and may aid in the design of membrane-active peptides with specified cellular targets and actions.

  13. Determination of functionalized gold nanoparticles incorporated in hydrophilic and hydrophobic microenvironments by surface modification of quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Tsui-Hsun [Institute of Biomedical Engineering, College of Engineering, College of Medicine, National Taiwan University, Taipei, Taiwan, ROC (China); Institute of Medical Mechatronics, Chang Gung University, Tao-Yuan, Taiwan, ROC (China); Liao, Shu-Chuan [Center of Thin Film Technologies and Applications, Mingchi University of Technology, Taipei, Taiwan, ROC (China); Chen, Ying-Fang [Department of Dentistry, Yun-Lin Branch, National Taiwan University Hospital, Dou-Liu, Yun-Lin, Taiwan, ROC (China); Huang, Yi-You [Institute of Biomedical Engineering, College of Engineering, College of Medicine, National Taiwan University, Taipei, Taiwan, ROC (China); Wei, Yi-Syuan [Department of Materials Engineering, Tatung University, 40 Zhongshan North Road, 3rd Section, Taipei 104, Taiwan, ROC (China); Tu, Shu-Ju, E-mail: sjt@cgu.edu.tw [Department of Medical Imaging and Radiological Sciences, Chang Gung University, 259 Wen-Hwa, 1st Road, Kwei-Shan, Tao-Yuan 133, Taiwan, ROC (China); Chen, Ko-Shao, E-mail: kschen@ttu.edu.tw [Department of Materials Engineering, Tatung University, 40 Zhongshan North Road, 3rd Section, Taipei 104, Taiwan, ROC (China)

    2013-06-01

    In this study, plasma deposition methods were used to immobilize Au electrode of a quartz crystal microbalance (QCM) to create different microenvironments for mass measurement of various modified Au nanoparticles (AuNPs). AuNPs were modified by 11-mercaptoundecanoic acid (MUA) and 1-decanethiol (DCT) for potential applications to drug release, protective coatings, and immunosensors. We aimed to develop a highly sensitive and reliable method to quantify the mass of various modified AuNPs. The surface of AuNPs and Au electrode was coated with polymer films, as determined by Fourier transform infrared spectroscopy and atomic force microscopy. Measurements obtained for various AuNPs and the plasma-treated surface of the Au electrode were compared with those obtained for an untreated Au electrode. According to the resonant frequency shift of QCM, a linear relationship was observed that significantly differed for AuNPs, MUA-AuNPs, and DCT-AuNPs (R{sup 2} range, 0.94–0.965, 0.934–0.972, and 0.874–0.9514, respectively). Compared to inductively coupled plasma and micro-computerized tomography, the QCM method with plasma treatment has advantages of real-time monitoring, greater sensitivity, and lower cost. Our results demonstrate that surface modifications measured by a QCM system for various modified AuNPs were reliable.

  14. Functionalized biocompatible polyelectrolyte multilayers for drug delivery: In situ investigation of mechanical properties by dissipative quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Habibi, Neda [Department of Informatics, Bioengineering, Robotics and Systems Engineering, University of Genova, Genova (Italy); Nanotechnology and Advanced Material Institute, Isfahan University of Technology, Isfahan (Iran, Islamic Republic of); Pastorino, Laura, E-mail: laura.pastorino@unige.it [Department of Informatics, Bioengineering, Robotics and Systems Engineering, University of Genova, Genova (Italy); Ruggiero, Carmelina [Department of Informatics, Bioengineering, Robotics and Systems Engineering, University of Genova, Genova (Italy)

    2014-02-01

    Nanostructured polymeric capsules have been applied in different fields, and specifically are regarded as promising for smart drug delivery applications. The physical–chemical and mechanical properties, and thus the permeability of the polyelectrolyte multilayer shell, play an important role in efficient delivery. Quartz crystal microbalance working in liquid has been used for the characterization of the buildup process and of the viscoelastic properties of biocompatible multilayers and of their functionalization by S-layer proteins. Optical and scanning electron microscopy have been used for the morphological characterization of nanostructured capsules obtained at physiological conditions by the assembly of the characterized multilayers onto spherical cores and by their subsequent removal. The proposed functionalized biocompatible capsules can be regarded as promising candidates for smart drug delivery applications. - Graphical abstract: SEM image of nanostructured polymeric capsules made by 4 bilayers of collagen/alginate at pH 7.4. - Highlights: • Build-up of biocompatible multilayers and functionalization by S-layer proteins • Characterization of multilayer growth and mechanical properties by QCM • Fabrication of S-layer functionalized biocompatible capsules.

  15. Interaction between Heparin and Fibronectin:Using Quartz Crystal Microbalance with Dissipation, Immunochemistry and Isothermal Titration Calorimetry

    Institute of Scientific and Technical Information of China (English)

    LI Guicai; WANG Caiping; YANG Ping; ZHOU Jie; ZHU Pingchuan

    2015-01-01

    The adsorption behavior of heparin and ifbronectin was studied by quartz crystal microbalance with dissipation (QCM-D), and the interaction between heparin and fibronectin was evaluated using immunochemistry and isothermal titration calorimetry (ITC) measurement. The results showed that there was competitive adsorption between heparin and fibronectin, and the preadsorption of fibronectin could prevent subsequent heparin adsorption to some extent, and the adsorbed Hep/Fn complex on the surface was in a rigid form. The bioactivity of heparin and ifbronectin could be affected by the bulk concentration of each, and both heparin and ifbronectin in Hep/Fn complex formed under pH 4 condition displayed larger bioactivity than that formed under pH 7 condition. Moreover, the ifbronectin showed more exposed cell-binding sites at the pH value lower than physiological condition. The results of ITC further suggested that the interaction between heparin and ifbronectin under pH 4 was stronger than under pH 7, and the complex was also more stable. The study brings forth the detailed interaction between heparin and ifbronectin, which will be helpful for better understanding the interaction mechanism of the two biomolecules. The results may be potentially useful for the development of new generation of cardiovascular biomaterials.

  16. The use of quartz crystal microbalance with dissipation (QCM-D) for studying nanoparticle-induced platelet aggregation

    Science.gov (United States)

    Santos-Martinez, Maria Jose; Inkielewicz-Stepniak, Iwona; Medina, Carlos; Rahme, Kamil; D’Arcy, Deirdre M; Fox, Daniel; Holmes, Justin D; Zhang, Hongzhou; Radomski, Marek Witold

    2012-01-01

    Interactions between blood platelets and nanoparticles have both pharmacological and toxicological significance and may lead to platelet activation and aggregation. Platelet aggregation is usually studied using light aggregometer that neither mimics the conditions found in human microvasculature nor detects microaggregates. A new method for the measurement of platelet microaggregation under flow conditions using a commercially available quartz crystal microbalance with dissipation (QCM-D) has recently been developed. The aim of the current study was to investigate if QCM-D could be used for the measurement of nanoparticle-platelet interactions. Silica, polystyrene, and gold nanoparticles were tested. The interactions were also studied using light aggregometry and flow cytometry, which measured surface abundance of platelet receptors. Platelet activation was imaged using phase contrast and scanning helium ion microscopy. QCM-D was able to measure nanoparticle-induced platelet microaggregation for all nanoparticles tested at concentrations that were undetectable by light aggregometry and flow cytometry. Microaggregates were measured by changes in frequency and dissipation, and the presence of platelets on the sensor surface was confirmed and imaged by phase contrast and scanning helium ion microscopy. PMID:22275839

  17. Study of the Interaction of Trastuzumab and SKOV3 Epithelial Cancer Cells Using a Quartz Crystal Microbalance Sensor

    Directory of Open Access Journals (Sweden)

    Louise Elmlund

    2015-03-01

    Full Text Available Analytical methods founded upon whole cell-based assays are of importance in early stage drug development and in fundamental studies of biomolecular recognition. Here we have studied the binding of the monoclonal antibody trastuzumab to human epidermal growth factor receptor 2 (HER2 on human ovary adenocarcinoma epithelial cancer cells (SKOV3 using quartz crystal microbalance (QCM technology. An optimized procedure for immobilizing the cells on the chip surface was established with respect to fixation procedure and seeding density. Trastuzumab binding to the cell decorated sensor surface was studied, revealing a mean dissociation constant, KD, value of 7 ± 1 nM (standard error of the mean. This study provides a new perspective on the affinity of the antibody-receptor complex presented a more natural context compared to purified receptors. These results demonstrate the potential for using whole cell-based QCM assay in drug development, the screening of HER2 selective antibody-based drug candidates, and for the study of biomolecular recognition. This real time, label free approach for studying interactions with target receptors present in their natural environment afforded sensitive and detailed kinetic information about the binding of the analyte to the target.

  18. Plasma proteins adsorption mechanism on polyethylene-grafted poly(ethylene glycol) surface by quartz crystal microbalance with dissipation.

    Science.gov (United States)

    Jin, Jing; Jiang, Wei; Yin, Jinghua; Ji, Xiangling; Stagnaro, Paola

    2013-06-04

    Protein adsorption has a vital role in biomaterial surface science because it is directly related to the hemocompatibility of blood-contacting materials. In this study, monomethoxy poly(ethylene glycol) (mPEG) with two different molecular weights was grafted on polyethylene as a model to elucidate the adsorption mechanisms of plasma protein through quartz crystal microbalance with dissipation (QCM-D). Combined with data from platelet adhesion, whole blood clotting time, and hemolysis rate, the blood compatibility of PE-g-mPEG film was found to have significantly improved. Two adsorption schemes were developed for real-time monitoring of protein adsorption. Results showed that the preadsorbed bovine serum albumin (BSA) on the surfaces of PE-g-mPEG films could effectively inhibit subsequent adsorption of fibrinogen (Fib). Nonspecific protein adsorption of BSA was determined by surface coverage, not by the chain length of PEG. Dense PEG brush could release more trapped water molecules to resist BSA adsorption. Moreover, the preadsorbed Fib could be gradually displaced by high-concentration BSA. However, the adsorption and displacement of Fib was determined by surface hydrophilicity.

  19. Microscopic insight into role of protein flexibility during ion exchange chromatography by nuclear magnetic resonance and quartz crystal microbalance approaches.

    Science.gov (United States)

    Hao, Dongxia; Ge, Jia; Huang, Yongdong; Zhao, Lan; Ma, Guanghui; Su, Zhiguo

    2016-03-18

    Driven by the prevalent use of ion exchange chromatography (IEC) for polishing therapeutic proteins, many rules have been formulated to summarize the different dependencies between chromatographic data and various operational parameters of interest based on statically determined interactions. However, the effects of the unfolding of protein structures and conformational stability are not as well understood. This study focuses on how the flexibility of proteins perturbs retention behavior at the molecular scale using microscopic characterization approaches, including hydrogen-deuterium (H/D) exchange detected by NMR and a quartz crystal microbalance (QCM). The results showed that a series of chromatographic retention parameters depended significantly on the adiabatic compressibility and structural flexibility of the protein. That is, softer proteins with higher flexibility tended to have longer retention times and stronger affinities on SP Sepharose adsorbents. Tracing the underlying molecular mechanism using NMR and QCM indicated that an easily unfolded flexible protein with a more compact adsorption layer might contribute to the longer retention time on adsorbents. The use of NMR and QCM provided a previously unreported approach for elucidating the effect of protein structural flexibility on binding in IEC systems.

  20. Detection of Staphylococcus epidermidis by a Quartz Crystal Microbalance Nucleic Acid Biosensor Array Using Au Nanoparticle Signal Amplification

    Directory of Open Access Journals (Sweden)

    Weiling Fu

    2008-10-01

    Full Text Available Staphylococcus epidermidis is a critical pathogen of nosocomial blood infections, resulting in significant morbidity and mortality. A piezoelectric quartz crystal microbalance (QCM nucleic acid biosensor array using Au nanoparticle signal amplification was developed to rapidly detect S. epidermidis in clinical samples. The synthesized thiolated probes specific targeting S. epidermidis 16S rRNA gene were immobilized on the surface of QCM nucleic acid biosensor arrays. Hybridization was induced by exposing the immobilized probes to the PCR amplified fragments of S. epidermidis, resulting in a mass change and a consequent frequency shift of the QCM biosensor. To further enhance frequency shift results from above described hybridizations, streptavidin coated Au nanoparticles were conjugated to the PCR amplified fragments. The results showed that the lowest detection limit of current QCM system was 1.3×103 CFU/mL. A linear correlation was found when the concentration of S. epidermidis varied from 1.3×103 to 1.3×107 CFU/mL. In addition, 55 clinical samples were detected with both current QCM biosensor system and conventional clinical microbiological method, and the sensitivity and specificity of current QCM biosensor system were 97.14% and 100%, respectively. In conclusion, the current QCM system is a rapid, low-cost and sensitive method that can be used to identify infection of S. epidermidis in clinical samples.

  1. A combined experimental and theoretical study on the immunoassay of human immunoglobulin using a quartz crystal microbalance.

    Science.gov (United States)

    Liao, Po-Jen; Chang, Jeng-Shian; Chao, Sheng D; Chang, Hung-Chi; Huang, Kuan-Rong; Wu, Kuang-Chong; Wung, Tzong-Shyan

    2010-01-01

    We investigate a immunoassay biosensor that employs a Quartz Crystal Microbalance (QCM) to detect the specific binding reaction of the (Human IgG1)-(Anti-Human IgG1) protein pair under physiological conditions. In addition to experiments, a three dimensional time domain finite element method (FEM) was used to perform simulations for the biomolecular binding reaction in microfluidic channels. In particular, we discuss the unsteady convective diffusion in the transportation tube, which conveys the buffer solution containing the analyte molecules into the micro-channel where the QCM sensor lies. It is found that the distribution of the analyte concentration in the tube is strongly affected by the flow field, yielding large discrepancies between the simulations and experimental results. Our analysis shows that the conventional assumption of the analyte concentration in the inlet of the micro-channel being uniform and constant in time is inadequate. In addition, we also show that the commonly used procedure in kinetic analysis for estimating binding rate constants from the experimental data would underestimate these rate constants due to neglected diffusion processes from the inlet to the reaction surface. A calibration procedure is proposed to supplement the basic kinetic analysis, thus yielding better consistency with experiments.

  2. A Combined Experimental and Theoretical Study on the Immunoassay of Human Immunoglobulin Using a Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Jeng-Shian Chang

    2010-12-01

    Full Text Available We investigate a immunoassay biosensor that employs a Quartz Crystal Microbalance (QCM to detect the specific binding reaction of the (Human IgG1-(Anti-Human IgG1 protein pair under physiological conditions. In addition to experiments, a three dimensional time domain finite element method (FEM was used to perform simulations for the biomolecular binding reaction in microfluidic channels. In particular, we discuss the unsteady convective diffusion in the transportation tube, which conveys the buffer solution containing the analyte molecules into the micro-channel where the QCM sensor lies. It is found that the distribution of the analyte concentration in the tube is strongly affected by the flow field, yielding large discrepancies between the simulations and experimental results. Our analysis shows that the conventional assumption of the analyte concentration in the inlet of the micro-channel being uniform and constant in time is inadequate. In addition, we also show that the commonly used procedure in kinetic analysis for estimating binding rate constants from the experimental data would underestimate these rate constants due to neglected diffusion processes from the inlet to the reaction surface. A calibration procedure is proposed to supplement the basic kinetic analysis, thus yielding better consistency with experiments.

  3. Monitoring the effects of fibrinogen concentration on blood coagulation using quartz crystal microbalance (QCM) and its comparison with thromboelastography

    Science.gov (United States)

    Lakshmanan, Ramji S.; Efremov, Vitaly; Cullen, Sinéad; Byrne, Barry; Killard, Anthony J.

    2013-05-01

    Fibrinogen has been identified as a major risk factor in cardiovascular disorders. Fibrinogen (340 kDa) is a soluble dimeric glycoprotein found in plasma and is a major component of the coagulation cascade. It has been identified as a major risk factor in cardiovascular disorders. The time taken for its conversion to fibrin is usually used as an "endpoint" in most clot-based assays, without any information on dynamic changes in physical properties or kinetics of a forming clot. A global coagulation profile as measured by Thromboelastography® (TEG®) provides information on both the time and kinetics of changes in physical property of the forming clot. In this work, Quartz crystal microbalance (QCM), which is a piezoelectric resonator has been used to study coagulation of plasma and compared with TEG. The changes in resonant frequency (Δf) and half width at half maximum (HWHM or ΔΓ) were used to evaluate effect of fibrinogen concentration. It has been shown that TEG is less sensitive to low concentrations of fibrinogen and dilution while QCM is able to monitor clot formation in both the circumstances.

  4. Ultra-sensitive detection of zinc oxide nanowires using a quartz crystal microbalance and phosphoric acid DNA

    Science.gov (United States)

    Jang, Kuewhan; You, Juneseok; Park, Chanhoo; Park, Hyunjun; Choi, Jaeyeong; Choi, Chang-Hwan; Park, Jinsung; Lee, Howon; Na, Sungsoo

    2016-09-01

    Recent advancements of nanomaterials have inspired numerous scientific and industrial applications. Zinc oxide nanowires (ZnO NWs) is one of the most important nanomaterials due to their extraordinary properties. However, studies performed over the past decade have reported toxicity of ZnO NWs. Therefore, there has been increasing demand for effective detection of ZnO NWs. In this study, we propose a method for the detection of ZnO NW using a quartz crystal microbalance (QCM) and DNA probes. The detection method is based on the covalent interaction between ZnO NWs and the phosphoric acid group of single-stranded DNA (i.e., linker DNA), and DNA hybridization between the linker DNA and the probe DNA strand on the QCM electrode. Rapid, high sensitivity, in situ detection of ZnO NWs was demonstrated for the first time. The limit of detection was 10-4 μg ml-1 in deionized water, which represents a sensitivity that is 100000 times higher than the toxic ZnO NW concentration level. Moreover, the selectivity of the ZnO NW detection method was demonstrated by comparison with other types of nanowires and the method was able to detect ZnO NWs in tap water sensitively even after stored for 14 d in a refrigerator. The performance of our proposed method was sufficient to achieve detection of ZnO NW in the ‘real-world’ environment.

  5. Combined Bacteria Microarray and Quartz Crystal Microbalance Approach for Exploring Glycosignatures of Nontypeable Haemophilus influenzae and Recognition by Host Lectins.

    Science.gov (United States)

    Kalograiaki, Ioanna; Euba, Begoña; Proverbio, Davide; Campanero-Rhodes, María A; Aastrup, Teodor; Garmendia, Junkal; Solís, Dolores

    2016-06-01

    Recognition of bacterial surface epitopes by host receptors plays an important role in the infectious process and is intimately associated with bacterial virulence. Delineation of bacteria-host interactions commonly relies on the detection of binding events between purified bacteria- and host-target molecules. In this work, we describe a combined microarray and quartz crystal microbalance (QCM) approach for the analysis of carbohydrate-mediated interactions directly on the bacterial surface, thus preserving the native environment of the bacterial targets. Nontypeable Haemophilus influenzae (NTHi) was selected as a model pathogenic species not displaying a polysaccharide capsule or O-antigen-containing lipopolysaccharide, a trait commonly found in several important respiratory pathogens. Here, we demonstrate the usefulness of NTHi microarrays for exploring the presence of carbohydrate structures on the bacterial surface. Furthermore, the microarray approach is shown to be efficient for detecting strain-selective binding of three innate immune lectins, namely, surfactant protein D, human galectin-8, and Siglec-14, to different NTHi clinical isolates. In parallel, QCM bacteria-chips were developed for the analysis of lectin-binding kinetics and affinity. This novel QCM approach involves capture of NTHi on lectin-derivatized chips followed by formaldehyde fixation, rendering the bacteria an integrated part of the sensor chip, and subsequent binding assays with label-free lectins. The binding parameters obtained for selected NTHi-lectin pairs provide further insights into the interactions occurring at the bacterial surface.

  6. Peptide-membrane interactions of arginine-tryptophan peptides probed using quartz crystal microbalance with dissipation monitoring.

    KAUST Repository

    Rydberg, Hanna A

    2014-04-18

    Membrane-active peptides include peptides that can cross cellular membranes and deliver macromolecular cargo as well as peptides that inhibit bacterial growth. Some of these peptides can act as both transporters and antibacterial agents. It is desirable to combine the knowledge from these two different fields of membrane-active peptides into design of new peptides with tailored actions, as transporters of cargo or as antibacterial substances, targeting specific membranes. We have previously shown that the position of the amino acid tryptophan in the peptide sequence of three arginine-tryptophan peptides affects their uptake and intracellular localization in live mammalian cells, as well as their ability to inhibit bacterial growth. Here, we use quartz crystal microbalance with dissipation monitoring to assess the induced changes caused by binding of the three peptides to supported model membranes composed of POPC, POPC/POPG, POPC/POPG/cholesterol or POPC/lactosyl PE. Our results indicate that the tryptophan position in the peptide sequence affects the way these peptides interact with the different model membranes and that the presence of cholesterol in particular seems to affect the membrane interaction of the peptide with an even distribution of tryptophans in the peptide sequence. These results give mechanistic insight into the function of these peptides and may aid in the design of membrane-active peptides with specified cellular targets and actions.

  7. In situ NMR and electrochemical quartz crystal microbalance techniques reveal the structure of the electrical double layer in supercapacitors.

    Science.gov (United States)

    Griffin, John M; Forse, Alexander C; Tsai, Wan-Yu; Taberna, Pierre-Louis; Simon, Patrice; Grey, Clare P

    2015-08-01

    Supercapacitors store charge through the electrosorption of ions on microporous electrodes. Despite major efforts to understand this phenomenon, a molecular-level picture of the electrical double layer in working devices is still lacking as few techniques can selectively observe the ionic species at the electrode/electrolyte interface. Here, we use in situ NMR to directly quantify the populations of anionic and cationic species within a working microporous carbon supercapacitor electrode. Our results show that charge storage mechanisms are different for positively and negatively polarized electrodes for the electrolyte tetraethylphosphonium tetrafluoroborate in acetonitrile; for positive polarization charging proceeds by exchange of the cations for anions, whereas for negative polarization, cation adsorption dominates. In situ electrochemical quartz crystal microbalance measurements support the NMR results and indicate that adsorbed ions are only partially solvated. These results provide new molecular-level insight, with the methodology offering exciting possibilities for the study of pore/ion size, desolvation and other effects on charge storage in supercapacitors.

  8. Mercury Sorption and Desorption on Gold: A Comparative Analysis of Surface Acoustic Wave and Quartz Crystal Microbalance-Based Sensors.

    Science.gov (United States)

    Kabir, K M Mohibul; Sabri, Ylias M; Esmaielzadeh Kandjani, Ahmad; Matthews, Glenn I; Field, Matthew; Jones, Lathe A; Nafady, Ayman; Ippolito, Samuel J; Bhargava, Suresh K

    2015-08-04

    Microelectromechanical sensors based on surface acoustic wave (SAW) and quartz crystal microbalance (QCM) transducers possess substantial potential as online elemental mercury (Hg(0)) vapor detectors in industrial stack effluents. In this study, a comparison of SAW- and QCM-based sensors is performed for the detection of low concentrations of Hg(0) vapor (ranging from 24 to 365 ppbv). Experimental measurements and finite element method (FEM) simulations allow the comparison of these sensors with regard to their sensitivity, sorption and desorption characteristics, and response time following Hg(0) vapor exposure at various operating temperatures ranging from 35 to 75 °C. Both of the sensors were fabricated on quartz substrates (ST and AT cut quartz for SAW and QCM devices, respectively) and employed thin gold (Au) layers as the electrodes. The SAW-based sensor exhibited up to ∼111 and ∼39 times higher response magnitudes than did the QCM-based sensor at 35 and 55 °C, respectively, when exposed to Hg(0) vapor concentrations ranging from 24 to 365 ppbv. The Hg(0) sorption and desorption calibration curves of both sensors were found to fit well with the Langmuir extension isotherm at different operating temperatures. Furthermore, the Hg(0) sorption and desorption rate demonstrated by the SAW-based sensor was found to decrease as the operating temperature increased, while the opposite trend was observed for the QCM-based sensor. However, the SAW-based sensor reached the maximum Hg(0) sorption rate faster than the QCM-based sensor regardless of operating temperature, whereas both sensors showed similar response times (t90) at various temperatures. Additionally, the sorption rate data was utilized in this study in order to obtain a faster response time from the sensor upon exposure to Hg(0) vapor. Furthermore, comparative analysis of the developed sensors' selectivity showed that the SAW-based sensor had a higher overall selectivity (90%) than did the QCM

  9. Measuring water adsorption on mineral surfaces in air, CO2, and supercritical CO2 with a quartz-crystal microbalance

    Science.gov (United States)

    Bryan, C. R.; Wells, R. K.; Burton, P. D.; Heath, J. E.; Dewers, T. A.; Wang, Y.

    2011-12-01

    Carbon sequestration via underground storage in geologic formations is a proposed approach for reducing industrial CO2 emissions. However, current models for carbon injection and long-term storage of supercritical CO2 (scCO2) do not consider the development and stability of adsorbed water films at the scCO2-hydrophilic mineral interface. The thickness and properties of the water films control the surface tension and wettability of the mineral surface, and on the core scale, affect rock permeability, saturation, and capillary properties. The film thickness is strongly dependent upon the activity of water in the supercritical fluid, which will change as initially anhydrous scCO2 absorbs water from formation brine. As described in a companion paper by the coauthors, the thickness of the adsorbed water layer is controlled by the disjoining pressure; structural and van der Waals components dominate at low water activity, while electrostatic forces become more important with increasing film thickness (higher water activities). As scCO2 water activity and water layer thickness increase, concomitant changes in mineral surface properties and reservoir/caprock hydrologic properties will affect the mobility of the aqueous phase and of scCO2. Moreover, the development of a water layer may be critical to mineral dissolution reactions in scCO2. Here, we describe the use of a quartz-crystal microbalance (QCM) to monitor adsorption of water by mineral surfaces. QCMs utilize a piezoelectrically-stimulated quartz wafer to measure adsorbed or deposited mass via changes in vibrational frequency. When used to measure the mass of adsorbed liquid films, the frequency response of the crystal must be corrected for the viscoelastic, rather than elastic, response of the adsorbed layer. Results are presented for adsorption to silica in N2 and CO2 at one bar, and in scCO2. Additional data are presented for water uptake by clays deposited on a QCM wafer. In this case, water uptake occurs by the

  10. Label-free real-time acoustic sensing of microvesicle release from prostate cancer (PC3) cells using a Quartz Crystal Microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Stratton, Dan [Cellular and Molecular Immunology Research Centre, School of Human Sciences, London Metropolitan University, London (United Kingdom); Lange, Sigrun [University College London School of Pharmacy, 29-39 Brunswick Square, London WC1N 1AX (United Kingdom); Kholia, Sharad; Jorfi, Samireh; Antwi-Baffour, Samuel [Cellular and Molecular Immunology Research Centre, School of Human Sciences, London Metropolitan University, London (United Kingdom); Inal, Jameel, E-mail: j.inal@londonmet.ac.uk [Cellular and Molecular Immunology Research Centre, School of Human Sciences, London Metropolitan University, London (United Kingdom)

    2014-10-24

    Highlights: • Microvesiculating cells record loss of mass on a Quartz Crystal Microbalance. • Using the Quartz Crystal Microbalance microvesicles are measured at 0.24 pg. • The QCM-D reveals loss in viscoelastic properties in microvesiculating cells. - Abstract: Using a Quartz Crystal Microbalance with dissipation monitoring, QCM-D (label-free system) measuring changes in resonant frequency (Δf) that equate to mass deposited on a sensor, we showed the attachment, over a 60 min period, of a monolayer of PC3 cells to the gold electrodes of the quartz crystal sensor, which had been rendered hydrophilic. That MVs were released upon BzATP stimulation of cells was confirmed by NTA analysis (average 250 nm diameter), flow cytometry, showing high phosphatidylserine exposition and by fluorescent (Annexin V Alexa Fluor® 488-positive) and electron microscopy. Over a period of 1000s (16.7 min) during which early apoptosis increased from 4% plateauing at 10% and late apoptosis rose to 2%, the Δf increased 20 Hz, thereupon remaining constant for the last 1000s of the experiment. Using the Sauerbrey equation, the loss in mass, which corresponded to the release of 2.36 × 10{sup 6} MVs, was calculated to be 23 ng. We therefore estimated the mass of an MV to be 0.24 pg. With the deposition on the QCM-D of 3.5 × 10{sup 7} MVs over 200s, the decrease in Δf (Hz) gave an estimate of 0.235 pg per MV.

  11. Application of an Electrochemical Quartz Crystal Microbalance to the study of electrocatalytic films

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, J.S. Jr.

    1993-09-01

    The EQCM was used to study the deposition and composition of electrodeposited pure PbO{sub 2} and Bi-doped PbO{sub 2} active toward anodic oxygen-transfer reactions. Within the doped films, Bi is incorporated as Bi{sup +5} in the form of BiO{sub 2}A, where A is ClO{sub 4}{sup {minus}} or NO{sub 3}{sup {minus}}. For deposition of these 2 materials, changes in hydration between the Au oxide and the depositing film resulted in higher mass-to-charge ratios. XRD and XPS were used to study the films; the rutile structure of PbO{sub 2} is retained even with the Bi doping. The EQCM was also used to study the formation and dissolution of Au oxide and preoxide structures formed on the Au substrate electrodes in acidic media. The preoxide structures were AuOH and increased the surface mass. For the formation of stable Au films on quartz wafers, Ti interlayers between Au and quartz was found to be very effective.

  12. Electrochemical quartz crystal microbalance study on Au-supported Pt adlayers for electrocatalytic oxidation of methanol in alkaline solution

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Underpotential deposition(UPD) of Cu on an Au electrode followed by redox replacement reaction(RRR) of CuUPD with a Pt source(H2PtCl6 or K2PtCl4) yielded Au-supported Pt adlayers(for short,Pt(CuUPD-Pt4+)n/Au for H2PtCl6,or Pt(CuUPD-Pt2+)n/Au for K2PtCl4,where n denotes the number of UPD-redox replacement cycles).The electrochemical quartz crystal microbalance(EQCM) technique was used for the first time to quantitatively study the fabricated electrodes and estimate their mass-normalized specific electrocatalytic activity(SECA) for methanol oxidation in alkaline solution.In comparison with Pt(CuUPD-Pt2+)n/Au,Pt(CuUPD-Pt4+)n/Au exhibited a higher electrocatalytic activity,and the maximum SECA was obtained to be as high as 35.7 mA ?g?1 at Pt(CuUPD-Pt4+)3/Au.The layer-by-layer architecture of Pt atoms on Au is briefly discussed based on the EQCM-revealed redox replacement efficiency,and the calculated distribution percentages of bare Au sites agree with the experimental results deduced from the charge under the AuOx-reduction peaks.The EQCM is highly recommended as an efficient technique to quantitatively examine various electrode-supported catalyst adlayers,and the highly efficient catalyst adlayers of noble metals are promising in electrocatalysis relevant to biological,energy and environmental sciences and technologies.

  13. Sequential adsorption of bovine mucin and lactoperoxidase to various substrates studied with quartz crystal microbalance with dissipation.

    Science.gov (United States)

    Halthur, Tobias J; Arnebrant, Thomas; Macakova, Lubica; Feiler, Adam

    2010-04-01

    Mucin and lactoperoxidase are both natively present in the human saliva. Mucin provides lubricating and antiadhesive function, while lactoperoxidase has antimicrobial activity. We propose that combined films of the two proteins can be used as a strategy for surface modification in biomedical applications such as implants or biosensors. In order to design and ultilize mixed protein films, it is necessary to understand the variation in adsorption behavior of the proteins onto different surfaces and how it affects their interaction. The quartz crystal microbalance with dissipation (QCM-D) technique has been used to extract information of the adsorption properties of bovine mucin (BSM) and lactoperoxidase (LPO) to gold, silica, and hydrophobized silica surfaces. The information has further been used to retrieve information of the viscoelastic properties of the adsorbed film. The adsorption and compaction of BSM were found to vary depending on the nature of the underlying bare surface, adsorbing as a thick highly hydrated film with loops and tails extending out in the bulk on gold and as a thinner film with much lower adsorbed amount on silica; and on hydrophobic surfaces, BSM adsorbs as a flat and much more compact layer. On gold and silica, the highly hydrated BSM film is cross-linked and compacted by the addition of LPO, whereas the compaction is not as pronounced on the already more compact film formed on hydrophobic surfaces. The adsorption of LPO to bare surfaces also varied depending on the type of surface. The adsorption profile of BSM onto LPO-coated surfaces mimicked the adsorption to the underlying surface, implying little interaction between the LPO and BSM. The interaction between the protein layers was interpreted as a combination of electrostatic and hydrophobic interactions, which was in turn influenced by the interaction of the proteins with the different substrates.

  14. Adsorption of cobalt ferrite nanoparticles within layer-by-layer films: a kinetic study carried out using quartz crystal microbalance.

    Science.gov (United States)

    Alcantara, Gustavo B; Paterno, Leonardo G; Afonso, André S; Faria, Ronaldo C; Pereira-da-Silva, Marcelo A; Morais, Paulo C; Soler, Maria A G

    2011-12-28

    The paper reports on the successful use of the quartz crystal microbalance technique to assess accurate kinetics and equilibrium parameters regarding the investigation of in situ adsorption of nanosized cobalt ferrite particles (CoFe(2)O(4)--10.5 nm-diameter) onto two different surfaces. Firstly, a single layer of nanoparticles was deposited onto the surface provided by the gold-coated quartz resonator functionalized with sodium 3-mercapto propanesulfonate (3-MPS). Secondly, the layer-by-layer (LbL) technique was used to build multilayers in which the CoFe(2)O(4) nanoparticle-based layer alternates with the sodium sulfonated polystyrene (PSS) layer. The adsorption experiments were conducted by modulating the number of adsorbed CoFe(2)O(4)/PSS bilayers (n) and/or by changing the CoFe(2)O(4) nanoparticle concentration while suspended as a stable colloidal dispersion. Adsorption of CoFe(2)O(4) nanoparticles onto the 3-MPS-functionalized surface follows perfectly a first order kinetic process in a wide range (two orders of magnitude) of nanoparticle concentrations. These data were used to assess the equilibrium constant and the adsorption free energy. Alternatively, the Langmuir adsorption constant was obtained while analyzing the isotherm data at the equilibrium. Adsorption of CoFe(2)O(4) nanoparticles while growing multilayers of CoFe(2)O(4)/PSS was conducted using colloidal suspensions with CoFe(2)O(4) concentration in the range of 10(-8) to 10(-6) (moles of cobalt ferrite per litre) and for different numbers of cycles n = 1, 3, 5, and 10. We found the adsorption of CoFe(2)O(4) nanoparticles within the CoFe(2)O(4)/PSS bilayers perfectly following a first order kinetic process, with the characteristic rate constant growing with the increase of CoFe(2)O(4) nanoparticle concentration and decreasing with the rise of the number of LbL cycles (n). Additionally, atomic force microscopy was employed for assessing the LbL film roughness and thickness. We found the film

  15. Aerosol effective density measurement using scanning mobility particle sizer and quartz crystal microbalance with the estimation of involved uncertainty

    Directory of Open Access Journals (Sweden)

    B. Sarangi

    2015-12-01

    Full Text Available In this work, we have used scanning mobility particle sizer (SMPS and quartz crystal microbalance (QCM to estimate the effective density of aerosol particles. This approach is tested for aerosolized particles generated from the solution of standard materials of known density, i.e. ammonium sulfate (AS, ammonium nitrate (AN and sodium chloride (SC, and also applied for ambient measurement in New Delhi. We also discuss uncertainty involved in the measurement. In this method, dried particles are introduced in to a differential mobility analyzer (DMA, where size segregation was done based on particle electrical mobility. At the downstream of DMA, the aerosol stream is subdivided into two parts. One is sent to a condensation particle counter (CPC to measure particle number concentration, whereas other one is sent to QCM to measure the particle mass concentration simultaneously. Based on particle volume derived from size distribution data of SMPS and mass concentration data obtained from QCM, the mean effective density (ρeff with uncertainty of inorganic salt particles (for particle count mean diameter (CMD over a size range 10 to 478 nm, i.e. AS, SC and AN is estimated to be 1.76 ± 0.24, 2.08 ± 0.19 and 1.69 ± 0.28 g cm−3, which are comparable with the material density (ρ values, 1.77, 2.17 and 1.72 g cm−3, respectively. Among individual uncertainty components, repeatability of particle mass obtained by QCM, QCM crystal frequency, CPC counting efficiency, and equivalence of CPC and QCM derived volume are the major contributors to the expanded uncertainty (at k = 2 in comparison to other components, e.g. diffusion correction, charge correction, etc. Effective density for ambient particles at the beginning of winter period in New Delhi is measured to be 1.28 ± 0.12 g cm−3. It was found that in general, mid-day effective density of ambient aerosols increases with increase in CMD of particle size measurement but particle photochemistry is an

  16. Aerosol effective density measurement using scanning mobility particle sizer and quartz crystal microbalance with the estimation of involved uncertainty

    Science.gov (United States)

    Sarangi, Bighnaraj; Aggarwal, Shankar G.; Sinha, Deepak; Gupta, Prabhat K.

    2016-03-01

    In this work, we have used a scanning mobility particle sizer (SMPS) and a quartz crystal microbalance (QCM) to estimate the effective density of aerosol particles. This approach is tested for aerosolized particles generated from the solution of standard materials of known density, i.e. ammonium sulfate (AS), ammonium nitrate (AN) and sodium chloride (SC), and also applied for ambient measurement in New Delhi. We also discuss uncertainty involved in the measurement. In this method, dried particles are introduced in to a differential mobility analyser (DMA), where size segregation is done based on particle electrical mobility. Downstream of the DMA, the aerosol stream is subdivided into two parts. One is sent to a condensation particle counter (CPC) to measure particle number concentration, whereas the other one is sent to the QCM to measure the particle mass concentration simultaneously. Based on particle volume derived from size distribution data of the SMPS and mass concentration data obtained from the QCM, the mean effective density (ρeff) with uncertainty of inorganic salt particles (for particle count mean diameter (CMD) over a size range 10-478 nm), i.e. AS, SC and AN, is estimated to be 1.76 ± 0.24, 2.08 ± 0.19 and 1.69 ± 0.28 g cm-3, values which are comparable with the material density (ρ) values, 1.77, 2.17 and 1.72 g cm-3, respectively. Using this technique, the percentage contribution of error in the measurement of effective density is calculated to be in the range of 9-17 %. Among the individual uncertainty components, repeatability of particle mass obtained by the QCM, the QCM crystal frequency, CPC counting efficiency, and the equivalence of CPC- and QCM-derived volume are the major contributors to the expanded uncertainty (at k = 2) in comparison to other components, e.g. diffusion correction, charge correction, etc. Effective density for ambient particles at the beginning of the winter period in New Delhi was measured to be 1.28 ± 0.12 g cm-3

  17. Mass flux response comparisons of a 200-MHz surface acoustic wave (SAW) resonator microbalance to a 15-MHz thermoelectric quartz crystal microbalance (TQCM) in a high-vacuum environment

    Science.gov (United States)

    Wallace, Donald A.; Bowers, William D.

    1994-10-01

    Using a 200 MHz Surface Acoustic Wave (SAW) resonator device as a high-vacuum molecular deposition microbalance, similar to a bulk quartz crystal microbalance (QCM), and an often-used 15 MHz thermoelectric QCM (TQCM), a comparison of various parameters was made during a high-vacuum outgassing experiment. The source of molecular outgassing was a bright aluminum foil which was cooled to liquid nitrogen temperature and alternately, to ambient temperature. The two sensors, the SAW QCM and the TQCM were placed next to each other and viewed only the aluminum foil. In this high-vacuum environment, a comparison between various parameters, i.e., mass sensitivity, long term drift rate, stability, thermal effects and dynamic range of the SAW and the TQCM, was obtained.

  18. Measurement of deposition rate and ion energy distribution in a pulsed dc magnetron sputtering system using a retarding field analyzer with embedded quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Shailesh, E-mail: shailesh.sharma6@mail.dcu.ie [Dublin City University, Glasnevin, Dublin 9 (Ireland); Impedans Limited, Chase House, City Junction Business Park, Northern Cross, D17 AK63, Dublin 17 (Ireland); Gahan, David, E-mail: david.gahan@impedans.com; Scullin, Paul; Doyle, James; Lennon, Jj; Hopkins, M. B. [Impedans Limited, Chase House, City Junction Business Park, Northern Cross, D17 AK63, Dublin 17 (Ireland); Vijayaraghavan, Rajani K.; Daniels, Stephen [Dublin City University, Glasnevin, Dublin 9 (Ireland)

    2016-04-15

    A compact retarding field analyzer with embedded quartz crystal microbalance has been developed to measure deposition rate, ionized flux fraction, and ion energy distribution arriving at the substrate location. The sensor can be placed on grounded, electrically floating, or radio frequency (rf) biased electrodes. A calibration method is presented to compensate for temperature effects in the quartz crystal. The metal deposition rate, metal ionization fraction, and energy distribution of the ions arriving at the substrate location are investigated in an asymmetric bipolar pulsed dc magnetron sputtering reactor under grounded, floating, and rf biased conditions. The diagnostic presented in this research work does not suffer from complications caused by water cooling arrangements to maintain constant temperature and is an attractive technique for characterizing a thin film deposition system.

  19. Measurement of deposition rate and ion energy distribution in a pulsed dc magnetron sputtering system using a retarding field analyzer with embedded quartz crystal microbalance.

    Science.gov (United States)

    Sharma, Shailesh; Gahan, David; Scullin, Paul; Doyle, James; Lennon, Jj; Vijayaraghavan, Rajani K; Daniels, Stephen; Hopkins, M B

    2016-04-01

    A compact retarding field analyzer with embedded quartz crystal microbalance has been developed to measure deposition rate, ionized flux fraction, and ion energy distribution arriving at the substrate location. The sensor can be placed on grounded, electrically floating, or radio frequency (rf) biased electrodes. A calibration method is presented to compensate for temperature effects in the quartz crystal. The metal deposition rate, metal ionization fraction, and energy distribution of the ions arriving at the substrate location are investigated in an asymmetric bipolar pulsed dc magnetron sputtering reactor under grounded, floating, and rf biased conditions. The diagnostic presented in this research work does not suffer from complications caused by water cooling arrangements to maintain constant temperature and is an attractive technique for characterizing a thin film deposition system.

  20. Investigation of Bovine Serum Albumin (BSA Attachment onto Self-Assembled Monolayers (SAMs Using Combinatorial Quartz Crystal Microbalance with Dissipation (QCM-D and Spectroscopic Ellipsometry (SE.

    Directory of Open Access Journals (Sweden)

    Hanh T M Phan

    Full Text Available Understanding protein adsorption kinetics to surfaces is of importance for various environmental and biomedical applications. Adsorption of bovine serum albumin to various self-assembled monolayer surfaces including neutral and charged hydrophilic and hydrophobic surfaces was investigated using in-situ combinatorial quartz crystal microbalance with dissipation and spectroscopic ellipsometry. Adsorption of bovine serum albumin varied as a function of surface properties, bovine serum albumin concentration and pH value. Charged surfaces exhibited a greater quantity of bovine serum albumin adsorption, a larger bovine serum albumin layer thickness, and increased density of bovine serum albumin protein compared to neutral surfaces at neutral pH value. The quantity of adsorbed bovine serum albumin protein increased with increasing bovine serum albumin concentration. After equilibrium sorption was reached at pH 7.0, desorption of bovine serum albumin occurred when pH was lowered to 2.0, which is below the isoelectric point of bovine serum albumin. Our data provide further evidence that combinatorial quartz crystal microbalance with dissipation and spectroscopic ellipsometry is a sensitive analytical tool to evaluate attachment and detachment of adsorbed proteins in systems with environmental implications.

  1. Quartz Crystal Microbalance Coated with Sol-gel-derived Thin Films as Gas Sensor for NO Detection

    Directory of Open Access Journals (Sweden)

    S. J. O’Shea

    2003-10-01

    Full Text Available This paper presents the possibilities and properties of Indium tin oxide (ITO-covered quartz crystal as a NOx toxic gas-sensor. The starting sol-gel solution was prepared by mixing indium chloride dissolved in acetylacetone and tin chloride dissolved in ethanol (0-20% by weight. The ITO thin films were deposited on the gold electrodes of quartz crystal by spin-coating technique and subsequently followed a standard photolithography to pattern the derived films to ensure all sensors with the same sensing areas. All heat treatment processes were controlled below 500°C in order to avoid the piezoelectric characteristics degradation of quartz crystal (Quartz will lose its piezoelectricity at ~573°C due to the phase change from α to β. The electrical and structural properties of ITO thin films were characterized with Hall analysis system, TG/DTA, XRD, XPS, SEM and etc. The gas sensor had featured with ITO thin films of ~100nm as the receptor to sense the toxic gas NO and quartz crystal with frequency of 10MHz as the transducer to transfer the surface reactions (mass loading, etc into the frequency shift. A homemade setup had been employed to measure the sensor response under the static mode. The experimental results had indicated that the ITO-coated QCM had a good sensitivity for NO gas, ~12Hz/100ppm within 5mins. These results prove that the ITO-covered quartz crystals are usable as a gas sensor and as an analytical device.

  2. An erosion sensor based on a quartz crystal microbalance for quantitative determination of the cleaning efficiency in an ultrasonic vessel.

    Science.gov (United States)

    Jüschke, M; Koch, C; Dreyer, T

    2014-09-01

    The efficiency of ultrasonic cleaning vessels cannot be measured directly in an easy way. In the presented work, a sensor is developed which quantitatively measures the ablation of a test layer. The sensor element is a quartz crystal which is coated with a sacrificial layer. Small changes in mass of this layer can be measured by a frequency shift of the crystal oscillation. For measurements, a 10 MHz AT-cut quartz crystal was used in a cleaning vessel working at 44.9 kHz. To determine the frequency shift by the ablation of the test layer, the quartz crystal was driven by a frequency generator sweeping the frequency in the range of the resonance frequency and a characteristic frequency was determined. The test layer which was applied to the quartz crystal consisted of silica microparticles suspended in varnish. In a preliminary experiment using a commercial cleaner it could be shown that significant changes in resonance frequency by cavitation effect could be detected. The initial frequency shift of the sacrificial layer is reproducible within 10%. The test layer can be adapted to the conditions of the cleaning vessel. By changing the electrical input power of the vessel, a threshold in the cavitation erosion was found.

  3. Broadband 120 MHz Impedance Quartz Crystal Microbalance (QCM with Calibrated Resistance and Quantitative Dissipation for Biosensing Measurements at Higher Harmonic Frequencies

    Directory of Open Access Journals (Sweden)

    Manuel Kasper

    2016-05-01

    Full Text Available We developed an impedance quartz crystal microbalance (QCM approach with the ability to simultaneously record mass changes and calibrated energy dissipation with high sensitivity using an impedance analyzer. This impedance QCM measures frequency shifts and resistance changes of sensing quartz crystals very stable, accurately, and calibrated, thus yielding quantitative information on mass changes and dissipation. Resistance changes below 0.3 Ω were measured with corresponding dissipation values of 0.01 µU (micro dissipation units. The broadband impedance capabilities allow measurements between 20 Hz and 120 MHz including higher harmonic modes of up to 11th order for a 10 MHz fundamental resonance frequency quartz crystal. We demonstrate the adsorbed mass, calibrated resistance, and quantitative dissipation measurements on two biological systems including the high affinity based avidin-biotin interaction and nano-assemblies of polyelectrolyte layers. The binding affinity of a protein-antibody interaction was determined. The impedance QCM is a versatile and simple method for accurate and calibrated resistance and dissipation measurements with broadband measurement capabilities for higher harmonics measurements.

  4. Decoupling mass adsorption from fluid viscosity and density in quartz crystal microbalance measurements using normalized conductance modeling

    Science.gov (United States)

    Parlak, Z.; Biet, C.; Zauscher, S.

    2013-08-01

    We describe the physical understanding of a method which differentiates between the frequency shift caused by fluid viscosity and density from that caused by mass adsorption in the resonance of a quartz crystal resonator. This method uses the normalized conductance of the crystal to determine a critical frequency at which the fluid mass and fluid loss compensate each other. Tracking the shift in this critical frequency allows us to determine purely mass adsorption on the crystal. We extended this method to Maxwellian fluids for understanding the mass adsorption in non-Newtonian fluids. We validate our approach by real-time mass adsorption measurements using glycerol and albumin solutions.

  5. On the lipid-bacterial protein interaction studied by quartz crystal microbalance with dissipation, transmission electron microscopy and atomic force microscopy

    CERN Document Server

    Delcea, Mihaela; Pum, Dietmar; Sleytr, Uwe Bernd; Toca-Herrera, Jose Luis

    2009-01-01

    The interaction between the bacterial S-protein SbpA on different types of lipid membranes has been studied using atomic force microscopy, transmission electron microscopy, and quartz crystal microbalance with dissipation. On one hand, It has been found that the bacterial forms two dimensional nanocrystals on zwitterionic DOPC bilayers and negatively charged DMPG vesicles adsorbed on mica, on zwitterionic DPPC and charged DPPC/DMPG (1:1) monolayers adsorbed on carbon grids. On the other hand, SbpA protein adsorption took place on zwitterionic DOPC bilayers and DOPC/DOPS (4:1) bilayers, previously adsorbed on silicon supports. SbpA adsorption also took place on DPPC/DOPS (1:1) monolayers adsorbed on carbon grids. Finally, neither SbpA adsorption, nor recrystallization was observed on zwitterionic DMPC vesicles (previously adsorbed on polyelectrolyte multilayers), and on DPPC vesicles supported on silicon.

  6. Development and application of quartz crystal microbalance sensor based on novel molecularly imprinted sol-gel polymer for rapid detection of histamine in foods.

    Science.gov (United States)

    Dai, Jie; Zhang, Yan; Pan, Mingfei; Kong, Lingjie; Wang, Shuo

    2014-06-11

    To rapidly detect histamine (HA) in foods, a novel material for HA-specific recognition was synthesized by a sol-gel process and coated on a quartz crystal microbalance (QCM) sensor. The Scatchard model was used to evaluate the adsorption performance of the material; high affinity for HA was demonstrated. Based on QCM frequency change, the sensor exhibited linear behavior for HA concentrations of 0.11 × 10(-2) to 4.45 × 10(-2) mg L(-1), a detection limit of 7.49 × 10(-4) mg kg(-1) (S/N = 3), high selectivity for HA (selectivity coefficient >4) compared with structural analogues, good reproducibility, and long-term stability. The sensor was used to determine the concentration of HA in spiked fish products; the recovery values were satisfactory (93.2-100.4%) and compared well with those obtained by high-performance liquid chromatography (correlation coefficient, r(2) = 0.9965).

  7. Determination of flux ionization fraction using a quartz crystal microbalance and a gridded energy analyzer in an ionized magnetron sputtering system

    Science.gov (United States)

    Green, K. M.; Hayden, D. B.; Juliano, D. R.; Ruzic, D. N.

    1997-12-01

    A diagnostic which combines a quartz crystal microbalance (QCM) and a gridded energy analyzer has been developed to measure the metal flux ionization fraction in a modified commercial dc magnetron sputtering device. The sensor is mounted on a linear motion feedthrough and embedded in a slot in the substrate plane to allow for measuring the uniformity in deposition and ionization throughout the plane of the wafer. Radio-frequency (rf) power is introduced through a coil to ionize the Al atoms. The metal flux ionization fraction at the QCM is determined by comparing the total deposition rate with and without a bias that screens out the ions, but that leaves the plasma undisturbed. By varying the voltage applied to the grids, the plasma potential is determined. At a pressure of 35 mTorr, a magnetron power of 2 kW, and a net rf power of 310±5 W, 78±5% ionization was found.

  8. Separate measurement of the density and viscosity of a liquid using a quartz crystal microbalance based on admittance analysis (QCM-A)

    Science.gov (United States)

    Itoh, Atsushi; Ichihashi, Motoko

    2011-01-01

    We previously used a quartz crystal microbalance (QCM) to identify a frequency f2 that allows measurement of the mass load without being affected by the viscous load of a liquid in the liquid phase. Here, we determined that frequency in order to separately measure the density and viscosity of a Newtonian liquid. Martin et al separately measured the density and viscosity of a liquid by immersing two quartz resonators, i.e. a smooth-surface resonator and a textured-surface resonator, in the liquid. We used a QCM based on admittance analysis (QCM-A) in the current study to separately measure the viscosity and density of a liquid using only a textured-surface resonator. In the current experiments, we measured the density and viscosity of 500 µl of 10%, 30%, and 50% aqueous glycerol solutions and compared the measured values to reference values. The density obtained had an error of ±1.5% of reference values and the viscosity had an error of about ±5% of reference values. Similar results were obtained with 500 µl of 10%, 30%, and 50% ethanol solutions. Measurement was possible with a quartz resonator, so measurements were made with even smaller samples. The density and viscosity of a liquid were successfully determined with an extremely small amount of liquid, i.e. 10 µl, with almost the same precision as when using 500 µl of the liquid.

  9. Label-free real-time acoustic sensing of microvesicle release from prostate cancer (PC3) cells using a Quartz Crystal Microbalance.

    Science.gov (United States)

    Stratton, Dan; Lange, Sigrun; Kholia, Sharad; Jorfi, Samireh; Antwi-Baffour, Samuel; Inal, Jameel

    2014-10-24

    Using a Quartz Crystal Microbalance with dissipation monitoring, QCM-D (label-free system) measuring changes in resonant frequency (Δf) that equate to mass deposited on a sensor, we showed the attachment, over a 60min period, of a monolayer of PC3 cells to the gold electrodes of the quartz crystal sensor, which had been rendered hydrophilic. That MVs were released upon BzATP stimulation of cells was confirmed by NTA analysis (average 250nm diameter), flow cytometry, showing high phosphatidylserine exposition and by fluorescent (Annexin V Alexa Fluor® 488-positive) and electron microscopy. Over a period of 1000s (16.7min) during which early apoptosis increased from 4% plateauing at 10% and late apoptosis rose to 2%, the Δf increased 20Hz, thereupon remaining constant for the last 1000s of the experiment. Using the Sauerbrey equation, the loss in mass, which corresponded to the release of 2.36×10(6)MVs, was calculated to be 23ng. We therefore estimated the mass of an MV to be 0.24pg. With the deposition on the QCM-D of 3.5×10(7)MVs over 200s, the decrease in Δf (Hz) gave an estimate of 0.235pg per MV.

  10. Use of quartz crystal microbalance to study the effect of chloride, sulphate and magnesium ions on the scaling rate; Apport de la microbalance a quartz dans l'etude de l'influence des ions sulfate, chlorure et magnesium sur la cinetique d'entartrage

    Energy Technology Data Exchange (ETDEWEB)

    Ben Amor, Y.; Triki, E. [Ecole Nationale d' Ingenieurs de Tunis, Unite de Recherche Corrosion et Protection des Metalliques (Tunisia); Bousselmi, I. [Institut National de Recherche Scientifique et Technologique, Lab. des Eaux et Environnement, Hammam-Lif (Tunisia); Sutter, E.; Labbe, J.P.; Fiaud, C. [Universite Pierre et Marie Curie, Lab. de Genie des Procedes Plasmas et Traitements de Surface, 75 - Paris (France)

    2004-07-01

    In this work, an electrochemical quartz crystal microbalance was used to study the effect of chloride, sulphate and magnesium ions on the scaling rate of gold in synthesized water. The chrono-electro-gravimetric results allow the evaluation of the nucleation and crystal growth steps. Infrared analysis of deposits was used to interpret the kinetic data, particularly in SO{sub 4}{sup 2-} and Mg{sup 2+} containing. Threshold effects were identified in each situation and essentially attributed to adsorption phenomena of ions on the metal and/or on the scale layers, as indicated by the influence of electrode potential and concentration of ions in solutions. (authors)

  11. Results from a Novel Method for Corrosion Studies of Electroplated Lithium Metal Based on Measurements with an Impedance Scanning Electrochemical Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Martin Winter

    2013-07-01

    Full Text Available A new approach to study the chemical stability of electrodeposited lithium on a copper metal substrate via measurements with a fast impedance scanning electrochemical quartz crystal microbalance is presented. The corrosion of electrochemically deposited lithium was compared in two different electrolytes, based on lithium difluoro(oxalato borate (LiDFOB and lithium hexafluorophosphate, both salts being dissolved in solvent blends of ethylene carbonate and diethyl carbonate. For a better understanding of the corrosion mechanisms, scanning electron microscopy images of electrodeposited lithium were also consulted. The results of the EQCM experiments were supported by AC impedance measurements and clearly showed two different corrosion mechanisms caused by the different salts and the formed SEIs. The observed mass decrease of the quartz sensor of the LiDFOB-based electrolyte is not smooth, but rather composed of a series of abrupt mass fluctuations in contrast to that of the lithium hexafluorophosphate-based electrolyte. After each slow decrease of mass a rather fast increase of mass is observed several times. The slow mass decrease can be attributed to a consolidation process of the SEI or to the partial dissolution of the SEI leaving finally lithium metal unprotected so that a fast film formation sets in entailing the observed fast mass increases.

  12. Nucleation and growth of hydroxyapatite on arc-deposited TiO{sub 2} surfaces studied by quartz crystal microbalance with dissipation

    Energy Technology Data Exchange (ETDEWEB)

    Lilja, Mirjam [Division for Nanotechnology and Functional Materials, Department of Engineering Sciences, The Ångström Laboratory, Uppsala University, Box 534, 75121 Uppsala (Sweden); Sandvik Coromant Sverige AB, Lerkrogsvägen 19, 12680 Stockholm (Sweden); Butt, Umer [Sandvik Coromant Sverige AB, Lerkrogsvägen 19, 12680 Stockholm (Sweden); Berzelii Centre EXSELENT on Porous Materials and Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, 114 18 Stockholm (Sweden); Shen, Zhijian [Berzelii Centre EXSELENT on Porous Materials and Department of Materials and Environmental Chemistry, Arrhenius Laboratory, Stockholm University, 114 18 Stockholm (Sweden); Bjöörn, Dorota, E-mail: dorota.bjoorn@sandvik.com [Sandvik Coromant Sverige AB, Lerkrogsvägen 19, 12680 Stockholm (Sweden)

    2013-11-01

    Understanding of nucleation and growth kinetics of biomimetically deposited hydroxyapatite (HA) on crystalline TiO{sub 2} surfaces is important with respect to the application and performance of HA as functional implant coatings. Arc-evaporation was used to deposit TiO{sub 2} coatings dominated by anatase phase, rutile phase or their mixtures. Subsequent formation of HA from phosphate buffered saline solution (PBS) was investigated in real-time using in situ quartz crystal microbalance with dissipation technique (QCM-D). Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were employed to characterize the presence, morphology and crystal structure of TiO{sub 2} coatings and the formed HA. Increasing temperature of the PBS, increasing flow rate and applying a higher ion concentration in solution were found to accelerate HA nucleation process and hence affect growth kinetics. Lower PBS temperature resulted in the formation of HA coatings with flake-like morphology and increasing HA porosity. All TiO{sub 2} coatings under study enabled HA formation at body temperature, while in contrast Ti reference surfaces only supported HA nucleation and growth at elevated temperatures. QCM-D technique is a powerful tool for studying the impact of process parameters during biomimetic coating deposition on coating structure evolution in real time and provides valuable information for understanding, optimizing as well as tailoring the biomimetic HA growth processes.

  13. Protein adsorption behaviors on chitosan/poly(ε-caprolactone) blend films studied by quartz crystal microbalance with dissipation monitoring(QCM-D)

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Chitosan/poly(ε-caprolactone) (PCL) blend films in different mass ratios were prepared using the chitosan/PCL mixture solutions in 80 vol.-% acetic acid by spin coating. Their surface micromorphologies were assessed by atomic force microscopy (AFM). It was found that the micromorphology of chitosan/PCL blend films was in large extent related to the mass ratio of chitosan. 25 wt% chitosan/PCL blend film presented microphase separation. The protein adsorption of bovine serum albumin (BSA) onto chitosan/PCL blend films was investigated by using quartz crystal microbalance with dissipation monitoring (QCM-D) in real time. The results suggested that the amount of adsorbed BSA on the chitosan/PCL blend films decreased with the addition of chitosan, but the structure and viscoelastic properties of the adsorbed BSA layers were greatly affected by the surface micromorphology of chitosan/PCL blend films. BSA absorbed on the 25 wt% chitosan/PCL blend film with microphase separa- tion showed larger adsorption reversibility, and preferred to form a loose, dissipative layer in comparison with those on other chitosan/PCL blend films without microphase separation.

  14. Investigation of photoelectrochemical oxidation of Fe{sup 2+} ions on porous nanocrystalline TiO{sub 2} electrodes using electrochemical quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Si Shihui; Huang Kelong; Wang Xiaoguang; Huang Mingzhi; Chen Hanfang

    2002-12-20

    The photoelectrochemical oxidation of Fe{sup 2+} ions on porous nanocrystalline TiO{sub 2} electrodes was investigated using in situ electrochemical quartz crystal microbalance (QCM). It was found that the adsorption of Fe{sup 2+} ions at the surface of TiO{sub 2} electrodes strongly depended on the pH of the solution, and that the saturated amount of adsorbed Fe{sup 2+} ions was approximately 4.4 ions nm{sup -2} at pH 4. The protons produced in photochemical reactions could cause the release of adsorbed Fe{sup 2+} ions from TiO{sub 2} surface, therefore, the frequency of QCM increased at the initial stage of illumination, during which the direct oxidation of adsorbed Fe{sup 2+} ions by photogenerated holes was dominant. When the frequency decreased, the major reaction was the photoelectrochemical deposition of Fe{sub 2}O{sub 3} from the bulk solution via a hydroxyl radical-mediated oxidation pathway, whose efficiency depended on the Fe{sup 2+} ion concentration.

  15. A quick responding quartz crystal microbalance sensor array based on molecular imprinted polyacrylic acids coating for selective identification of aldehydes in body odor.

    Science.gov (United States)

    Jha, Sunil K; Hayashi, Kenshi

    2015-03-01

    In present work, a novel quartz crystal microbalance (QCM) sensor array has been developed for prompt identification of primary aldehydes in human body odor. Molecularly imprinted polymers (MIP) are prepared using the polyacrylic acid (PAA) polymer matrix and three organic acids (propenoic acid, hexanoic acid and octanoic acid) as template molecules, and utilized as QCM surface coating layer. The performance of MIP films is characterized by 4-element QCM sensor array (three coated with MIP layers and one with pure PAA for reference) dynamic and static responses to target aldehydes: hexanal, heptanal, and nonanal in single, binary, and tertiary mixtures at distinct concentrations. The target aldehydes were selected subsequent to characterization of body odor samples with solid phase-micro extraction gas chromatography mass spectrometer (SPME-GC-MS). The hexanoic acid and octanoic acid imprinted PAA exhibit fast response, and better sensitivity, selectivity and reproducibility than the propenoic acid, and non-imprinted PAA in array. The response time and recovery time for hexanoic acid imprinted PAA are obtained as 5 s and 12 s respectively to typical concentrations of binary and tertiary mixtures of aldehydes using the static response. Dynamic sensor array response matrix has been processed with principal component analysis (PCA) for visual, and support vector machine (SVM) classifier for quantitative identification of target odors. Aldehyde odors were identified successfully in principal component (PC) space. SVM classifier results maximum recognition rate 79% for three classes of binary odors and 83% including single, binary, and tertiary odor classes in 3-fold cross validation.

  16. Protein adsorption behaviors on chitosan/poly(ε-caprolactone)blend films studied by quartz crystal microbalance with dissipation monitoring (QCM-D)

    Institute of Scientific and Technical Information of China (English)

    ZENG Rong; ZHANG Yi; LIANG ZhiHong; TU Mei; ZHOU ChangRen

    2009-01-01

    Chitosan/poly(ε-caprolactone)(PCL)blend films in different mass ratios were prepared using the chitosan/PCL mixture solutions in 80 vol.-% acetic acid by spin coating.Their surface micromorphologies were assessed by atomic force microscopy(AFM).It was found that the micromorphology of chitosan/PCL blend films was in large extent related to the mass ratio of chitosan.25 wt% chitosan/PCL blend film presented microphase separation.The protein adsorption of bovine serum albumin(BSA)onto chitosan/PCL blend films was investigated by using quartz crystal microbalance with dissipation monitoring(QCM-D)in real time.The results suggested that the amount of adsorbed BSA on the chitosan/PCL blend films decreased with the addition of chitosan,but the structure and viscoelastic properties of the adsorbed BSA layers were greatly affected by the surface micromorphology of chitosan/PCL blend films.BSA absorbed on the 25 wt% chitosan/PCL blend film with microphase separation showed larger adsorption reversibility,and preferred to form a loose,dissipative layer in comparison with those on other chitosan/PCL blend films without microphase separation.

  17. Assessment of DNA binding to human Rad51 protein by using quartz crystal microbalance and atomic force microscopy: effects of ADP and BRC4-28 peptide inhibitor.

    Science.gov (United States)

    Esnault, Charles; Renodon-Cornière, Axelle; Takahashi, Masayuki; Casse, Nathalie; Delorme, Nicolas; Louarn, Guy; Fleury, Fabrice; Pilard, Jean-François; Chénais, Benoît

    2014-12-01

    The interaction of human Rad51 protein (HsRad51) with single-stranded deoxyribonucleic acid (ssDNA) was investigated by using quartz crystal microbalance (QCM) monitoring and atomic force microscopy (AFM) visualization. Gold surfaces for QCM and AFM were modified by electrografting of the in situ generated aryldiazonium salt from the sulfanilic acid to obtain the organic layer Au-ArSO3 H. The Au-ArSO3 H layer was activated by using a solution of PCl5 in CH2 Cl2 to give a Au-ArSO2 Cl layer. The modified surface was then used to immobilize long ssDNA molecules. The results obtained showed that the presence of adenosine diphosphate promotes the protein autoassociation rather than nucleation around DNA. In addition, when the BRC4-28 peptide inhibitor was used, both QCM and AFM confirmed the inhibitory effect of BRC4-28 toward HsRad51 autoassociation. Altogether these results show the suitability of this modified surface to investigate the kinetics and structure of DNA-protein interactions and for the screening of inhibitors.

  18. Adsorption kinetics of laponite and ludox silica nanoparticles onto a deposited poly(diallyldimethylammonium chloride) layer measured by a quartz crystal microbalance and optical reflectometry.

    Science.gov (United States)

    Xu, Dan; Hodges, Chris; Ding, Yulong; Biggs, Simon; Brooker, Anju; York, David

    2010-12-07

    A quartz crystal microbalance with dissipation (QCM-D) and an optical reflectometer (OR) have been used to investigate the adsorption behavior of Laponite and Ludox silica nanoparticles at the solid-liquid interface. The adsorption of both Laponite and Ludox silica onto poly(diallyldimethylammonium chloride) (PDADMAC)-coated surfaces over the first few seconds were studied by OR. Both types of nanoparticles adsorbed rapidly and obtained a stable adsorbed amount after only a few minutes. The rate of adsorption for both nanoparticle types was concentration dependent. The maximum adsorption rate of Ludox nanoparticles was found to be approximately five times faster than that for Laponite nanoparticles. The QCM data for the Laponite remained stable after the initial adsorption period at each concentration tested. The observed plateau values for the frequency shifts increased with increasing Laponite particle concentration. The QCM data for the Ludox nanoparticles had a more complex long-time behavior. In particular, the dissipation data at 3 ppm and 10 ppm Ludox increased slowly with time, never obtaining a stable value within the duration of the experiment. We postulate here that this is caused by slow structural rearrangements of the particles and the PDADMAC within the surface adsorbed layer. Furthermore, the QCM dissipation values were significantly smaller for Laponite when compared with those for Ludox for all nanoparticle concentrations, suggesting that the Laponite adsorbed layer is more compact and more rigidly bound than the Ludox adsorbed layer.

  19. Quartz crystal microbalance with dissipation and microscale thermophoresis as tools for investigation of protein complex formation between thymidylate synthesis cycle enzymes.

    Science.gov (United States)

    Antosiewicz, Anna; Senkara, Elżbieta; Cieśla, Joanna

    2015-02-15

    Thymidylate synthase (TS) and dihydrofolate reductase (DHFR) play essential role in DNA synthesis, repair and cell division by catalyzing two subsequent reactions in thymidylate biosynthesis cycle. The lack of either enzyme leads to thymineless death of the cell, therefore inhibition of the enzyme activity is a common and successful tool in cancer chemotherapy and treatment of other diseases. However, the detailed mechanism of thymidylate synthesis cycle, especially the interactions between cycle enzymes and its role remain unknown. In this paper we are the first to show that human TS and DHFR enzymes form a strong complex which might be essential for DNA synthesis. Using two unique biosensor techniques, both highly sensitive to biomolecular interactions, namely quartz crystal microbalance with dissipation monitoring (QCM-D) and microscale thermophoresis (MST) we have been able to determine DHFR-TS binding kinetic parameters such as the Kd value being below 10 µM (both methods), k(on) = 0.46 × 10(4) M(-1) s(-1) and k(off) = 0.024 s(-1) (QCM-D). We also calculated Gibbs free energy as in the order of -30 kJ/mol and DHFR/TS molar ratio pointing to binding of 6 DHFR monomers per 1 TS dimer (both methods). Moreover, our data from MST analysis have pointed to positive binding cooperativity in TS-DHFR complex formation. The results obtained with both methods are comparable and complementary.

  20. Particle Characterization for a Protein Drug Product Stored in Pre-Filled Syringes Using Micro-Flow Imaging, Archimedes, and Quartz Crystal Microbalance with Dissipation.

    Science.gov (United States)

    Zheng, Songyan; Puri, Aastha; Li, Jinjiang; Jaiswal, Archana; Adams, Monica

    2017-01-01

    Micro-flow imaging (MFI) has been used for formulation development for analyzing sub-visible particles. Archimedes, a novel technique for analyzing sub-micron particles, has been considered as an orthogonal method to currently existing techniques. This study utilized these two techniques to investigate the effectiveness of polysorbate (PS-80) in mitigating the particle formation of a therapeutic protein formulation stored in silicone oil-coated pre-filled syringes. The results indicated that PS-80 prevented the formation of both protein and silicone oil particles. In the case of protein particles, PS-80 might involve in the interactions with the hydrophobic patches of protein, air bubbles, and the stressed surfaces of silicone oil-coated pre-filled syringes. Such interactions played a role in mitigating the formation of protein particles. Subsequently, quartz crystal microbalance with dissipation (QCM-D) was utilized to characterize the interactions associated with silicone oil, protein, and PS-80 in the solutions. Based on QCM-D results, we proposed that PS-80 likely formed a layer on the interior surfaces of syringes. As a result, the adsorbed PS-80 might block the leakage of silicone oil from the surfaces to solution so that the silicone oil particles were mitigated at the presence of PS-80. Overall, this study demonstrated the necessary of utilizing these three techniques cooperatively in order to better understand the interfacial role of PS-80 in mitigating the formation of protein and silicone oil particles.

  1. Mucoadhesion vs mucus permeability of thiolated chitosan polymers and their resulting nanoparticles using a quartz crystal microbalance with dissipation (QCM-D).

    Science.gov (United States)

    Oh, Sejin; Borrós, Salvador

    2016-11-01

    The aim of this present study was to evaluate the combination properties between mucoadhesion/mucus permeability of thiolated chitosans (TC) and their resulting nanoparticles using a quartz crystal microbalance with dissipation (QCM-D). The QCM-D experiments were conducted at pH 4 or 6.8 to assess the interaction between thiolated polymers, with low (TCL), medium (TCM) and high (TCH) contents of free thiol groups, and native porcine gastric mucin (NPGM). TCL was chosen for further carriers as it showed higher permeability into the NPGM layer compared to TCM and TCH. In this study, we describe a formulation of a novel carrier comprised by positively charged TCL, negatively charged DNA and degradable oligopeptide-modified poly(β-amino ester)s (PBAEs), which were employed in order to approach for tuning particle size and surface charge of complexes. TCL/PBAE complexes with or without DNA were characterized using dynamic light scattering. Mechanism of adsorption or permeation of the TCL/PBAE/DNA complexes into the NPGM barrier was investigated with QCM-D, which is a highly sensitive technique for studying nanomechanical (viscoelastic) changes of the substrates. This work might provide that the QCM-D technique would be a promising method to monitor the dynamic behaviour between complexes and NPGM.

  2. Application of a quartz crystal microbalance to the study of copper corrosion in acid solution inhibited by triazole-iodide protective films

    Energy Technology Data Exchange (ETDEWEB)

    Jope, D.; Sell, J.; Pickering, H.W.; Weil, K.G. [Pennsylvania State Univ., University Park, PA (United States). Dept. of Materials Science and Engineering

    1995-07-01

    When one uses one side of a quartz crystal microbalance as the working electrode in electrochemical experiments, mass changes can be monitored continuously with a sensitivity of a few nanograms per square centimeter. In this study the working electrode consisted of electrolytically deposited copper, exposed to 0.1M sodium sulfate at pH 3, open to the atmosphere and in some cases containing H{sub 2}O{sub 2}. Upon addition of one of the inhibitors, benzotriazole (BTA), tolyltriazole (TTA), carboxy-benzotriazole (CBT), or these inhibitors plus potassium iodide, the rate of frequency change decreases markedly. After removal of the inhibitors from the corrosive medium by fast solution exchange there is a marked continuing protective effect of the inhibitor films in the cases of BTA + KI and TTA + KI with the latter being the most stable and protective of all of the films. The results were qualitatively the same in the more corrosive solution containing H{sub 2}O{sub 2}.

  3. Characterization of the native and denatured herceptin by enzyme linked immunosorbent assay and quartz crystal microbalance using a high-affinity single chain fragment variable recombinant antibody.

    Science.gov (United States)

    Shang, Yuqin; Mernaugh, Ray; Zeng, Xiangqun

    2012-10-02

    Herceptin/Trastuzumab is a humanized IgG1κ light chain antibody used to treat some forms of breast cancer. A phage-displayed recombinant antibody library was used to obtain a single chain fragment variable (scFv, designated 2B4) to a linear synthetic peptide representing Herceptin's heavy chain CDR3. Enzyme linked immunosorbent assays (ELISAs) and piezoimmunosensor/quartz crystal microbalance (QCM) assays were used to characterize 2B4-binding activity to both native and heat denatured Herceptin. The 2B4 scFv specifically bound to heat denatured Herceptin in a concentration dependent manner over a wide (35-220.5 nM) dynamic range. Herceptin denatures and forms significant amounts of aggregates when heated. UV-vis characterization confirms that Herceptin forms aggregates as the temperature used to heat Herceptin increases. QCM affinity assay shows that binding stoichiometry between 2B4 scFv and Herceptin follows a 1:2 relationship proving that 2B4 scFv binds strongly to the dimers of heat denatured Herceptin aggregates and exhibits an affinity constant of 7.17 × 10(13) M(-2). The 2B4-based QCM assay was more sensitive than the corresponding ELISA. Combining QCM with ELISA can be used to more fully characterize nonspecific binding events in assays. The potential theoretical and clinical implications of these results and the advantages of the use of QCM to characterize human therapeutic antibodies in samples are also discussed.

  4. Electrochemistry, surface plasmon resonance, and quartz crystal microbalance: an associative study on cytochrome c adsorption on pyridine tail-group monolayers on gold.

    Science.gov (United States)

    Paulo, Tércio de F; de Sousa, Ticyano P; de Abreu, Dieric S; Felício, Nathalie H; Bernhardt, Paul V; Lopes, Luiz G de F; Sousa, Eduardo H S; Diógenes, Izaura C N

    2013-07-25

    Quartz crystal microbalance (QCM), surface plasmon resonance (SPR), and electrochemistry techniques were used to study the electron-transfer (ET) reaction of cytochrome c (Cyt c) on gold surfaces modified with thionicotinamide, thioisonicotinamide, 4-mercaptopyridine, 5-(4-pyridyl)-1,3,4-oxadiazole-2-thiol, 5-phenyl-1,3,4-oxadiazole-2-thiol, 4,4'-bipyridine, and 4,4'-dithiopyridine. The electrochemical results showed that the ET process is complex, being chiefly diffusional with steps depending on the orientation of the pyridine or phenyl tail group of the modifiers. The correlation between the electrochemical results and those acquired by SPR and QCM indicated the presence of an adlayer of Cyt c adsorbed on the thiolate SAMs. This adlayer, although being not electroactive, is essential to assess the ET reaction of Cyt c in solution. The results presented in this work are consistent with the statement (Feng, Z. Q.; Imabayashi, S.; Kakiuchi, T.; Niki, K. J. Electroanal. Chem. 1995, 394, 149-154) that the ET reaction of Cyt c can be explained in terms of the through-bond tunneling mechanism.

  5. Electrochemical quartz crystal microbalance studies on enzymatic specific activity and direct electrochemistry of immobilized glucose oxidase in the presence of sodium dodecyl benzene sulfonate and multiwalled carbon nanotubes.

    Science.gov (United States)

    Su, Yuhua; Xie, Qingji; Chen, Chao; Zhang, Qingfang; Ma, Ming; Yao, Shouzhuo

    2008-01-01

    The electrochemical quartz crystal microbalance (EQCM) technique was utilized to monitor in situ the adsorption of glucose oxidase (GOD) and the mixture of GOD and sodium dodecyl benzene sulfonate (SDBS) onto Au electrodes with and without modification of multiwalled carbon nanotubes (MWCNTs) or SDBS/MWCNTs composite, and the relationship between enzymatic specific activity (ESA) and direct electrochemistry of the immobilized GOD was quantitatively evaluated for the first time. Compared with the bare gold electrode at which a little GOD was adsorbed and the direct electrochemistry of the adsorbed GOD was negligible, the amount and electroactivity of adsorbed GOD were greatly enhanced when the GOD was mixed with SDBS and then adsorbed onto the SDBS/MWCNTs modified Au electrode. However, the ESA of the adsorbed GOD was fiercely decreased to only 16.1% of the value obtained on the bare gold electrode, and the portion of adsorbed GOD showing electrochemical activity exhibited very low enzymatic activity, demonstrating that the electroactivity and ESA of immobilized GOD responded oppositely to the presence of MWCNTs and SDBS. The ESA results obtained from the EQCM method were well supported by conventional UV-vis spectrophotometry. The direct electrochemistry of redox proteins including enzymes as a function of their biological activities is an important concern in biotechnology, and this work may have presented a new and useful protocol to quantitatively evaluate both the electroactivity and ESA of trace immobilized enzymes, which is expected to find wider applications in biocatalysis and biosensing fields.

  6. Quartz crystal microbalance study of ionic strength and pH-dependent polymer conformation and protein adsorption/desorption on PAA, PEO, and mixed PEO/PAA brushes.

    Science.gov (United States)

    Delcroix, M F; Demoustier-Champagne, S; Dupont-Gillain, C C

    2014-01-14

    The conformation of polymer chains grafted on a substrate influences protein adsorption. In a previous study, adsorption/desorption of albumin was demonstrated on mixed poly(ethylene oxide) (PEO)/poly(acrylic acid) (PAA) brushes, triggered by solutions of adequate pH and ionic strength (I). In the present work, homolayers of PEO or PAA are submitted to saline solutions with pH from 3 to 9 and I from 10(-5) to 10(-1) M, and their conformation is evaluated in real time using quartz crystal microbalance with dissipation monitoring (QCM-D). Shrinkage/swelling of PAA chains and hydration and salt condensation in the brush are evidenced. The adsorption of human serum albumin (HSA) onto such brushes is also monitored in these different saline solutions, leading to a deep understanding of the influence of polymer chain conformation, modulated by pH and I, on protein adsorption. A detailed model of the conformation of PEO/PAA mixed brushes depending on pH and I is then proposed, providing a rationale for the identification of conditions for the successive adsorption and desorption of proteins on such mixed brushes. The adsorption/desorption of albumin on PEO/PAA is demonstrated using QCM-D.

  7. Detection of Cry2A Protein Based on Quartz Crystal Microbalance Technique%Cry2A蛋白的石英晶体微天平检测

    Institute of Scientific and Technical Information of China (English)

    杜方; 黄新; 纪淑娟

    2014-01-01

    目的:建立检测苏云金芽孢杆菌Cry2A蛋白的石英晶体微天平(quartz crystal microbalance,QCM)传感方法.方法:根据抗原抗体相互作用原理,利用QCM技术,在金片表面修饰抗原所对应的单克隆抗体,对苏云金芽孢杆菌Cry2A蛋白进行检测研究.结果:该方法灵敏度达到1μg/mL,特异性好、重复性高.结论:该方法有利于为苏云金芽孢杆菌蛋白检测提供新思路,可以应用到实际样品的检测,在农产品转基因检测和进出口检验检疫中具有很好的应用前景.

  8. 1-Butyl-3-Methylimidazolium Tetrafluoroborate Film as a Highly Selective Sensing Material for Non-Invasive Detection of Acetone Using a Quartz Crystal Microbalance

    Directory of Open Access Journals (Sweden)

    Wenyan Tao

    2017-01-01

    Full Text Available Breath acetone serves as a biomarker for diabetes. This article reports 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4], a type of room temperature ionic liquid (RTIL, as a selective sensing material for acetone. The RTIL sensing layer was coated on a quartz crystal microbalance (QCM for detection. The sensing mechanism is based on a decrease in viscosity and density of the [bmim][BF4] film due to the solubilization of acetone leading to a positive frequency shift in the QCM. Acetone was detected with a linear range from 7.05 to 750 ppmv. Sensitivity and limit of detection were found to be 3.49 Hz/ppmv and 5.0 ppmv, respectively. The [bmim][BF4]-modified QCM sensor demonstrated anti-interference ability to commonly found volatile organic compounds in breath, e.g., isoprene, 1,2-pentadiene, d-limonene, and dl-limonene. This technology is useful for applications in non-invasive early diabetic diagnosis.

  9. Quantification of the viscoelasticity of the bond of biotic and abiotic particles adhering to solid-liquid interfaces using a window-equipped quartz crystal microbalance with dissipation.

    Science.gov (United States)

    van der Westen, Rebecca; van der Mei, Henny C; De Raedt, Hans; Olsson, Adam L J; Busscher, Henk J; Sharma, Prashant K

    2016-12-01

    The quartz-crystal-microbalance-with-dissipation (QCM-D) has become a powerful tool for studying the bond viscoelasticity of biotic and abiotic colloidal particles adhering to substratum surfaces. A window-equipped QCM-D allows high-throughput analysis of the average bond viscoelasticity, measuring over 10(6) particles simultaneously in one single experiment. Other techniques require laborious analyses of individual particles. In this protocol, the quantitative derivation of the spring-constant and drag-coefficient of the bond between adhering colloidal particles and substratum surfaces using QCM-D is explained for bacteria and silica particles, using the particle-mass derived for validation. Bond viscoelasticity is calculated using a coupled resonator model, paying special attention to the protocol for mathematical fitting needed to obtain reliable quantitative output. Knowledge of the viscoelasticity of the bond between colloidal particles and substratum surfaces facilitates development of new strategies to detach adhering particles from or retain them on a surface. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. 1-Butyl-3-Methylimidazolium Tetrafluoroborate Film as a Highly Selective Sensing Material for Non-Invasive Detection of Acetone Using a Quartz Crystal Microbalance

    Science.gov (United States)

    Tao, Wenyan; Lin, Peng; Liu, Sili; Xie, Qingji; Ke, Shanming; Zeng, Xierong

    2017-01-01

    Breath acetone serves as a biomarker for diabetes. This article reports 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]), a type of room temperature ionic liquid (RTIL), as a selective sensing material for acetone. The RTIL sensing layer was coated on a quartz crystal microbalance (QCM) for detection. The sensing mechanism is based on a decrease in viscosity and density of the [bmim][BF4] film due to the solubilization of acetone leading to a positive frequency shift in the QCM. Acetone was detected with a linear range from 7.05 to 750 ppmv. Sensitivity and limit of detection were found to be 3.49 Hz/ppmv and 5.0 ppmv, respectively. The [bmim][BF4]-modified QCM sensor demonstrated anti-interference ability to commonly found volatile organic compounds in breath, e.g., isoprene, 1,2-pentadiene, d-limonene, and dl-limonene. This technology is useful for applications in non-invasive early diabetic diagnosis. PMID:28117697

  11. A living cell quartz crystal microbalance biosensor for continuous monitoring of cytotoxic responses of macrophages to single-walled carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Marx Kenneth A

    2011-01-01

    Full Text Available Abstract Background Numerous engineered nanomaterials (ENMs exist and new ENMs are being developed. A challenge to nanotoxicology and environmental health and safety is evaluating toxicity of ENMs before they become widely utilized. Cellular assays remain the predominant test platform yet these methods are limited by using discrete time endpoints and reliance on organic dyes, vulnerable to interference from ENMs. Label-free, continuous, rapid response systems with biologically meaningful endpoints are needed. We have developed a device to detect and monitor in real time responses of living cells to ENMs. The device, a living cell quartz crystal microbalance biosensor (QCMB, uses macrophages adherent to a quartz crystal. The communal response of macrophages to treatments is monitored continuously as changes in crystal oscillation frequency (Δf. We report the ability of this QCMB to distinguish benign from toxic exposures and reveal unique kinetic information about cellular responses to varying doses of single-walled carbon nanotubes (SWCNTs. Results We analyzed macrophage responses to additions of Zymosan A, polystyrene beads (PBs (benign substances or SWCNT (3-150 μg/ml in the QCMB over 18 hrs. In parallel, toxicity was monitored over 24/48 hrs using conventional viability assays and histological stains to detect apoptosis. In the QCMB, a stable unchanging oscillation frequency occurred when cells alone, Zymosan A alone, PBs alone or SWCNTs without cells at the highest dose alone were used. With living cells in the QCMB, when Zymosan A, PBs or SWCNTs were added, a significant decrease in frequency occurred from 1-6 hrs. For SWCNTs, this Δf was dose-dependent. From 6-18 hrs, benign substances or low dose SWCNT (3-30 μg/ml treatments showed a reversal of the decrease of oscillation frequency, returning to or exceeding pre-treatment levels. Cell recovery was confirmed in conventional assays. The lag time to see the Δf reversal in QCMB plots

  12. Quartz crystal microbalance: a useful tool for studying thin polymer films and complex biomolecular systems at the solution-surface interface.

    Science.gov (United States)

    Marx, Kenneth A

    2003-01-01

    The quartz crystal microbalance (QCM) is a simple, cost effective, high-resolution mass sensing technique, based upon the piezoelectric effect. As a methodology, the QCM evolved a solution measurement capability in largely analytical chemistry and electrochemistry applications due to its sensitive solution-surface interface measurement capability. The technique possesses a wide detection range. At the low mass end, it can detect monolayer surface coverage by small molecules or polymer films. At the upper end, it is capable of detecting much larger masses bound to the surface. These can be complex arrays of biopolymers and biomacromolecules, even whole cells. In addition, the QCM can provide information about the energy dissipating properties of the bound surface mass. Another important and unique feature of the technique is the ability to measure mass and energy dissipation properties of films while simultaneously carrying out electrochemistry on solution species or upon film systems bound to the upper electrode on the oscillating quartz crystal surface. These measurements can describe the course of electropolymerization of a film or can reveal ion or solute transport within a film during changes in the film environment or state, including the oxidation state for an electroactive film driven by the underlying surface potential. The past decade has witnessed an explosive growth in the application of the QCM technique to the study of a wide range of molecular systems at the solution-surface interface, in particular, biopolymer and biochemical systems. In this report, we start with a brief historical and technical overview. Then we discuss the application of the QCM technique to measurements involving micellar systems, self-assembling monolayers and their phase transition behavior, molecularly imprinted polymers, chemical sensors, films formed using the layer-by-layer assembly technique, and biopolymer films and point out the utility of the electrochemical

  13. Nanoassembled thin film gas sensors. III. Sensitive detection of amine odors using TiO2/poly(acrylic acid) ultrathin film quartz crystal microbalance sensors.

    Science.gov (United States)

    Lee, Seung-Woo; Takahara, Naoki; Korposh, Sergiy; Yang, Do-Hyeon; Toko, Kiyoshi; Kunitake, Toyoki

    2010-03-15

    Quartz crystal microbalance (QCM) gas sensors based on the alternate adsorption of TiO(2) and polyacrilic acid (PAA) were developed for the sensitive detection of amine odors. Individual TiO(2) gel layers could be regularly assembled with a thickness of approximately 0.3 nm by the gas-phase surface sol-gel process (GSSG). The thickness of the poly(acrylic acid) (PAA) layer is dependent on its molecular weight, showing different thicknesses of approximately 0.4 nm for PAA(25) (Mw 250,000) and 0.6-0.8 nm for PAA(400) (Mw 4,000,000). The QCM sensors showed a linear response to ammonia in the concentration range 0.3-15 ppm, depending on the deposition cycle of the alternate TiO(2)/PAA layer. The ammonia binding is based on the acid-base interaction to the free carboxylic acid groups of PAA and the limit of detection (LOD) of the 20-cycle TiO(2)/PAA(400) film was estimated to be 0.1 ppm when exposed to ammonia. The sensor response was very fast and stable in a wide relative humidity (rH) range of 30-70%, showing almost the same frequency changes at a given concentration of ammonia. Sensitivity to n-butylamine and ammonia was higher than to pyridine, which is owing to the difference of molecular weight and basicity of the amine analytes. The alternate TiO(2)/PAA(400) films have a highly effective ability to capture amine odors, and the ambient ammonia concentration of 15 ppm could be condensed up to approximately 20,000 ppm inside the films.

  14. Specific Surface versus Electrochemically Active Area of the Carbon/Polypyrrole Capacitor: Correlation of Ion Dynamics Studied by an Electrochemical Quartz Crystal Microbalance with BET Surface.

    Science.gov (United States)

    Mosch, Heike L K S; Akintola, Oluseun; Plass, Winfried; Höppener, Stephanie; Schubert, Ulrich S; Ignaszak, Anna

    2016-05-10

    Carbon/polypyrrole (PPy) composites are promising electrode materials for energy storage applications such as lightweight capacitors. Although these materials are composed of relatively inexpensive components, there is a gap of knowledge regarding the correlation between surface, porosity, ion exchange dynamics, and the interplay of the double layer capacitance and pseudocapacitance. In this work we evaluate the specific surface area analyzed by the BET method and the area accessible for ions using electrochemical quartz-crystal microbalance (EQCM) for SWCNT/PPy and carbon black Vulcan XC72-R/PPy composites. The study revealed that the polymer has significant influence on the pore size of the composites. Although the BET surface is low for the polypyrrole, the electrode mass change and thus the electrochemical area are large for the polymer-containing electrodes. This indicates that multiple redox active centers in the charged polymer chain are good ion scavengers. Also, for the composite electrodes, the effective charge storage occurs at the polypyrrole-carbon junctions, which are easy to design/multiply by a proper carbon-to-polymer weight ratio. The specific BET surface and electrochemically accessible surface area are both important parameters in calculation of the electrode capacitance. SWCNTs/PPy showed the highest capacitances normalized to the BET and electrochemical surface as compared to the polymer-carbon black. TEM imaging revealed very homogeneous distribution of the nanosized polymer particles onto the CNTs, which facilitates the synergistic effect of the double layer capacitance (CNTs) and pseudocapacitance (polymer). The trend in the electrode mass change in correlation with the capacitance suggest additional effects such as a solvent co-insertion into the polymer and the contribution of the charge associated with the redox activity of oxygen-containing functional groups on the carbon surface.

  15. Deposition of selenium thin layers on gold surfaces from sulphuric acid media: Studies using electrochemical quartz crystal microbalance, cyclic voltammetry and AFM

    Energy Technology Data Exchange (ETDEWEB)

    Cabral, Murilo Feitosa [Instituto de Quimica de Sao Carlos, Universidade de Sao Paulo, C.P. 780, 13566-590 Sao Carlos, SP (Brazil); Pedrosa, Valber A., E-mail: vzp0002@auburn.ed [Department of Materials Engineering, Samuel Ginn College of Engineering, Auburn University, Auburn, AL 36849 (United States); Spinola Machado, Sergio Antonio [Instituto de Quimica de Sao Carlos, Universidade de Sao Paulo, C.P. 780, 13566-590 Sao Carlos, SP (Brazil)

    2010-01-01

    In this paper we report here new considerations about the relationship between the mass and charge variations (m/z relationship) in underpotential deposition (UPD), bulk deposition and also in the H{sub 2}Se formation reaction. Nanogravimetric experiments were able to show the adsorption of H{sub 2}SeO{sub 3} on the AuO surface prior to the voltammetric sweep and that, after the AuO reduction, 0.40 monolayer of H{sub 2}SeO{sub 3} remains adsorbed on the newly reduced Au surface, which was enough to gives rise to the UPD layer. The UPD results indicate that the maximum coverage with Se{sub ads} on polycrystalline gold surface corresponds to approximately 0.40 monolayer, in good agreement with charge density results. The cyclic voltammetry experiments demonstrated that the amount of bulk Se obtained during the potential scan to approximately 2 Se monolayers, which was further confirmed by electrochemical quartz crystal microbalance (EQCM) measurements that pointed out a mass variation corresponding of 3 monolayers of Se. In addition, the Se thin films were obtained by chronoamperometric experiments, where the Au electrode was polarized at +0.10 V during different times in 1.0 M H{sub 2}SO{sub 4} + 1.0 mM SeO{sub 2}. The topologic aspects of the electrodeposits were observed in Atomic Force Microscope (AFM) measurements. Finally, in highly negative potential polarizations, the H{sub 2}Se formation was analyzed by voltammetric and nanogravimetric measurements. These finding brings a new light on the selenium electrodeposition and point up to a proposed electrochemical model for molecule controlled surface engineering.

  16. Evaluating the Effect of Surface Roughness on Titanium Dioxide Nanoparticle Deposition using a Combined Quartz Crystal Microbalance with Dissipation (QCM-D) and Generalized Ellipsometry (GE) Technique

    Science.gov (United States)

    Kananizadeh, N.; Lee, J.; Rodenhausen, K. B.; Sekora, D.; Schubert, M.; Schubert, E.; Bartelt-Hunt, S.; Li, Y.

    2016-12-01

    Quantification and characterization of nanoparticles in soils and sediments are very challenging because they will interact not only with soil-water chemistry but also with highly heterogeneous soil and sediment surfaces. In this work, we measured the interaction of Titanium dioxide nanoparticles (nTiO2), the most extensively manufactured engineered materials, with engineered rough surfaces under varied ionic strength conditions. Innovative three-dimensional Silicon nanostructured surfaces, referred to here as slanted columnar thin films (SCTFs), were used to generate surface roughness with controlled heights of 50nm, 100nm, and 200nm. Using atomic layer deposition technique (ALD), surfaces of SCTF were coated with either silicon dioxide or aluminum oxides to represent the most abundant silica aquifer materials and metal oxide impurities, respectively. The interaction between nTiO2 and model rough surfaces was measured using quartz crystal microbalance with dissipation monitoring (QCM-D). The data were analyzed using a model that couples the viscoelastic effect with the surface roughness effect. No nTiO2 deposition was observed on neither flat nor rough silicon dioxide surfaces under ionic strength ranged from 0 to 100 mM NaCl. On the other hand, the deposition of nTiO2 on the aluminum oxides coated surfaces increased as the height of roughness increased. In parallel with QCM-D, a Generalized Ellipsometry (GE) was used to measure the mass of deposited nTiO2. The combination of QCM-D and GE revealed that the properties (i.e. porosity and rigidness) of attached nTiO2 layer on the QCM-D surfaces were dependent on ionic strength and surface roughness.

  17. A method of layer-by-layer gold nanoparticle hybridization in a quartz crystal microbalance DNA sensing system used to detect dengue virus

    Science.gov (United States)

    Chen, Sz-Hau; Chuang, Yao-Chen; Lu, Yi-Chen; Lin, Hsiu-Chao; Yang, Yun-Liang; Lin, Chih-Sheng

    2009-05-01

    Dengue virus (DENV) is nowadays the most important arthropod-spread virus affecting humans existing in more than 100 countries worldwide. A rapid and sensitive detection method for the early diagnosis of infectious dengue virus urgently needs to be developed. In the present study, a circulating-flow quartz crystal microbalance (QCM) biosensing method combining oligonucleotide-functionalized gold nanoparticles (i.e. AuNP probes) used to detect DENV has been established. In the DNA-QCM method, two kinds of specific AuNP probes were linked by the target sequences onto the QCM chip to amplify the detection signal, i.e. oscillatory frequency change (ΔF) of the QCM sensor. The target sequences amplified from the DENV genome act as a bridge for the layer-by-layer AuNP probes' hybridization in the method. Besides being amplifiers of the detection signal, the specific AuNP probes used in the DNA-QCM method also play the role of verifiers to specifically recognize their target sequences in the detection. The effect of four AuNP sizes on the layer-by-layer hybridization has been evaluated and it is found that 13 nm AuNPs collocated with 13 nm AuNPs showed the best hybridization efficiency. According to the nanoparticle application, the DNA-QCM biosensing method was able to detect dengue viral RNA in virus-contaminated serum as plaque titers being 2 PFU ml-1 and a linear correlation (R2 = 0.987) of ΔF versus virus titration from 2 × 100 to 2 × 106 PFU ml-1 was found. The sensitivity and specificity of the present DNA-QCM method with nanoparticle technology showed it to be comparable to the fluorescent real-time PCR methods. Moreover, the method described herein was shown to not require expensive equipment, was label-free and highly sensitive.

  18. On the electric double-layer structure at carbon electrode/organic electrolyte solution interface analyzed by ac impedance and electrochemical quartz-crystal microbalance responses

    Energy Technology Data Exchange (ETDEWEB)

    Kim, In-Tae; Egashira, Minato; Yoshimoto, Nobuko [Department of Applied Chemistry, Graduate School of Science and Engineering, Yamaguchi University, 2-16-1, Tokiwadai, Ube 755-8611 (Japan); Morita, Masayuki, E-mail: morita@yamaguchi-u.ac.jp [Department of Applied Chemistry, Graduate School of Science and Engineering, Yamaguchi University, 2-16-1, Tokiwadai, Ube 755-8611 (Japan)

    2011-08-30

    Highlights: {center_dot} We monitored resonance frequency change of smooth surface carbon electrode to determine mass changes during electrochemical polarization.{center_dot} This was done from viewpoints of ensuring the electric double-layer structure in organic electrolytes.{center_dot} Clear difference was observed in the mass changes among the electrolyte composition.{center_dot} It were related with differences in the double-layer capacitance at carbon. - Abstract: ac impedance and electrochemical quartz crystal microbalance (EQCM) techniques have been applied to analyze the structure of electric double-layer formed at carbon/organic electrolyte solution interface using a sputtered carbon electrode. The mass changes caused by electrochemical adsorption (accumulation) of ions have been estimated in the solutions of propylene carbonate (PC) dissolving tetrafluoroborate (BF{sub 4}{sup -}) salts of lithium (Li{sup +}), tetraethylammonium (TEA{sup +}) and tetra-n-butylammonium (TBA{sup +}) cations. The observed mass changes during the cathodic polarization in the solutions containing TEA{sup +} and TBA{sup +} were well consistent with those expected by the calculation based on mono-layer adsorption of the cations with giving the consideration to the surface roughness. On the other hand, the mass change observed in the solution containing Li{sup +} salt showed that the solvation of Li{sup +} with three or four molecules of PC would be the charge compensation species at the interface. Comparison of the quantity of the electricity passed during the EQCM measurements with that from theoretical calculation with simple Helmholtz-layer model revealed that the major part of the double-layer capacitance would be based on the electrostatic polarization of the solvent molecule directly adsorbed at the carbon surface.

  19. The impact of water and hydrocarbon concentration on the sensitivity of a polymer-based quartz crystal microbalance sensor for organic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Pejcic, Bobby, E-mail: Bobby.Pejcic@csiro.au [CSIRO, Earth Science and Resource Engineering, PO Box 1130, Bentley, WA 6102 (Australia); Crooke, Emma [CSIRO, Earth Science and Resource Engineering, PO Box 1130, Bentley, WA 6102 (Australia); Doherty, Cara M.; Hill, Anita J. [CSIRO, Materials Science and Engineering, Locked Bag 33, Clayton Sth MDC, Vic 3169 (Australia); Myers, Matthew [CSIRO, Earth Science and Resource Engineering, PO Box 1130, Bentley, WA 6102 (Australia); University of Western Australia, School of Biomedical, Biomolecular and Chemical Sciences, Crawley, WA 6009 (Australia); Qi, Xiubin; Ross, Andrew [CSIRO, Earth Science and Resource Engineering, PO Box 1130, Bentley, WA 6102 (Australia)

    2011-10-03

    Highlights: {yields} The response of a polymer coated QCM sensor is affected by water soaking time. {yields} Polymer-water interfacial processes influence the QCM sensitivity for hydrocarbons. {yields} The QCM sensitivity of high Tg polymer films is affected by plasticization processes. - Abstract: Long-term environmental monitoring of organic compounds in natural waters requires sensors that respond reproducibly and linearly over a wide concentration range, and do not degrade with time. Although polymer coated piezoelectric based sensors have been widely used to detect hydrocarbons in aqueous solution, very little information exists regarding their stability and suitability over extended periods in water. In this investigation, the influence of water aging on the response of various polymer membranes [polybutadiene (PB), polyisobutylene (PIB), polystyrene (PS), polystyrene-co-butadiene (PSB)] was studied using the quartz crystal microbalance (QCM). QCM measurements revealed a modest increase in sensitivity towards toluene for PB and PIB membranes at concentrations above 90 ppm after aging in water for 4 days. In contrast, the sensitivity of PS and PSB coated QCM sensors depended significantly on the toluene concentration and increased considerably at concentrations above 90 ppm after aging in water for 4 days. Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) showed that there is a change in the sorption mechanism at higher toluene levels for PS and PSB. Positron annihilation lifetime spectroscopy (PALS) studies were performed to investigate the free volume properties of all polymers and to monitor any changes in the free volume size and distribution due to water and toluene exposure. The PALS did not detect any considerable variation in the free volume properties of the polymer films as a function of solution composition and soaking time, implying that viscoelastic and/or interfacial processes (i.e. surface area changes) are probably

  20. A method of layer-by-layer gold nanoparticle hybridization in a quartz crystal microbalance DNA sensing system used to detect dengue virus

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S-H; Chuang, Y-C; Lu, Y-C; Lin, H-C; Yang, Y-L; Lin, C-S [Department of Biological Science and Technology, National Chiao Tung University, Hsinchu 30068, Taiwan (China)], E-mail: lincs@mail.nctu.edu.tw

    2009-05-27

    Dengue virus (DENV) is nowadays the most important arthropod-spread virus affecting humans existing in more than 100 countries worldwide. A rapid and sensitive detection method for the early diagnosis of infectious dengue virus urgently needs to be developed. In the present study, a circulating-flow quartz crystal microbalance (QCM) biosensing method combining oligonucleotide-functionalized gold nanoparticles (i.e. AuNP probes) used to detect DENV has been established. In the DNA-QCM method, two kinds of specific AuNP probes were linked by the target sequences onto the QCM chip to amplify the detection signal, i.e. oscillatory frequency change ({delta}F) of the QCM sensor. The target sequences amplified from the DENV genome act as a bridge for the layer-by-layer AuNP probes' hybridization in the method. Besides being amplifiers of the detection signal, the specific AuNP probes used in the DNA-QCM method also play the role of verifiers to specifically recognize their target sequences in the detection. The effect of four AuNP sizes on the layer-by-layer hybridization has been evaluated and it is found that 13 nm AuNPs collocated with 13 nm AuNPs showed the best hybridization efficiency. According to the nanoparticle application, the DNA-QCM biosensing method was able to detect dengue viral RNA in virus-contaminated serum as plaque titers being 2 PFU ml{sup -1} and a linear correlation (R{sup 2} = 0.987) of {delta}F versus virus titration from 2 x 10{sup 0} to 2 x 10{sup 6} PFU ml{sup -1} was found. The sensitivity and specificity of the present DNA-QCM method with nanoparticle technology showed it to be comparable to the fluorescent real-time PCR methods. Moreover, the method described herein was shown to not require expensive equipment, was label-free and highly sensitive.

  1. Electrochemical Quartz Crystal Nanobalance

    Science.gov (United States)

    Inzelt, György

    The method of piezoelectric microgravimetry (nanogravimetry) using an electrochemical quartz crystal microbalance (EQCM) or nanobalance (EQCN) can be considered as a novel and much more sensitive version of electrogravimetry. The EQCN technique has become a widely used technique in several areas of electrochemistry, electroanalytical chemistry, bioelectrochemistry, etc. [1-10]. Obviously, mass changes occurring during adsorption, sorption, electrosorption, electrodeposition, or spontaneous deposition can be followed, which is very helpful for the elucidation of reaction mechanism via identification of the species accumulated on the surface. These investigations include metal and alloy deposition, underpotential deposition, electroplating, synthesis of conducting polymers by electropolymerization, adsorption of biologically active materials, and analytical determination of small ions and biomolecules. Of course, the opposite processes, i.e., spontaneous dissolution, electrodissolution, corrosion, can also be studied. Electrochemical oscillations, in which the formation and oxidation of chemisorbed molecular fragments play a determining role, have been studied, too. The majority of the investigations have been devoted to ion and solvent transport associated with the redox transformations of electrochemically active polymers. Similar studies have been carried out regarding polynuclear surface layers such as metal hexacyanometalates as well as inorganic and organic microcrystals of different compositions.

  2. Nucleation-fibrillation dynamics of Aβ1-40 peptides on liquid-solid surface studied by total-internal-reflection fluorescence microscopy coupled with quartz-crystal microbalance biosensor

    Science.gov (United States)

    Hamada, Hiroki; Ogi, Hirotsugu; Noi, Kentaro; Yagi, Hisashi; Goto, Yuji; Hirao, Masahiko

    2015-07-01

    We have successfully developed the total-internal-reflection-fluorescence microscopy combined with a quartz-crystal microbalance (TIRFM-QCM) biosensor, and monitored the nucleation-fibrillation phenomenon of amyloid β1-40 peptide on the naked quartz surface. The cross-β-sheet structures were visualized with the TIRFM using the thioflavin-T (Th-T) label, and other unlabeled aggregates were detected through the frequency change of the 58-MHz wireless-electrodeless QCM throughout the aggregation reaction. The QCM response indicates significant adsorption of the peptides on the quartz surface at the early stage, which is followed by fibrillation. The non-cross-β-sheet oligomers are first formed, and nuclei appear in the oligomer region, from which fibrils originate and elongate. The two-color TIRFM observation was performed after the aggregation reaction with the Nile-red label as well as the ThT label for identifying nucleation from non-β-sheet regions. An aggregation model is proposed.

  3. A New Quartz Crystal Microbalance Measuring Method with Expansive Frequency Range and Broadband Adaptive Response Capacity%新型宽频自适应石英晶体微天平测量方法

    Institute of Scientific and Technical Information of China (English)

    周俊鹏; 包宇; 林青; 逄仁山; 王连明; 牛利

    2014-01-01

    In order to solve the problems of present quartz crystal microbalance ( QCM ) measuring instruments, such as high demand for crystal cutting technology and uncomprehensive measurements for crystal parameters, a modified quadrature demodulation-based method was proposed with broadband adaptive response capacity and high frequency resolution. Moreover, it is also capable of measuring both resonant frequencies and dissipation factor D synchronously and continuously. Experimental results at room temperature indicated that the adaptive frequency range was 1-9 MHz while the frequency resolution was less than 1 Hz, measured resonance frequency shifts of crystals in the range scale linearly with the equal thickness increments of poly acrylic acid ( PAA) membrane on the working electrode, and with the volatilization of different solvent factor D is measured continuously and effectively along the time axis. To sum up, compared with traditional ones, this new method has lower material cost and more obtained parameters.%针对目前石英晶体微天平( Quartz crystal microbalance,QCM)仪器所存在的对晶体切割工艺要求过高,测量参数不够全面等问题,在正交解调法的基础上,提出了一种在较宽频率范围内具有自适应功能,测量频率分辨率高,并且可同时连续获取谐振频率和耗散因子D的测试方法。实验表明:室温下,频率测量自适应范围在1~9 MHz且频率分辨率小于1 Hz;随着工作电极聚丙烯酸( Poly acrylic acid,PAA)膜厚度的均匀叠加,测得范围内各晶体频率偏移呈线性变化;随着不同溶剂挥发,D因子测量结果在时间轴上连续有效。与传统方法相比,本方法具有耗材成本低,获取参数丰富等优点。

  4. A Novel Signal-Amplified Immunoassay for the Detection of C-Reactive Protein Using HRP-Doped Magnetic Nanoparticles as Labels with the Electrochemical Quartz Crystal Microbalance as a Detector

    Directory of Open Access Journals (Sweden)

    Ning Gan

    2013-01-01

    Full Text Available A novel horseradish peroxidase- (HPR- doped magnetic core-shell Fe3O4@SiO2@Au nanocomposites (Fe-Au MNPs were employed on immunoassay for the determination of C-reactive protein (CRP based on a electrochemical quartz crystal microbalance detector (EQCM. Firstly, the secondary CRP antibody and HRP were both immobilized on the Fe-Au MNPs (Fe-Au MNPs-anti-CRP2/HRP as a signal tag. Secondly, the above tag and the primary antibody (anti-CRP1 in the bottom of 96-well microtiter plate were employed to conjugate with a serial of CRP concentrations to produce a sandwich immunocomplex. Thirdly, the immunocomplex solution was subsequently exposed to 3,3′-diaminobenzidine (DAB in the presence of H2O2, resulting in an insoluble product. When the precipitation solution was dripped on EQCM, it can achieve a decrease of frequency of crystal (Δf. The amount of Δf was proportional to (CRP from 0.003 to 200 ng mL−1 with a low detection limit of 1 pg mL−1. Compared with the enzyme-linked immunosorbent assay (ELISA, the immunoassay shows greatly improved sensitivity due to the significant amount of HRP labeled on signal tag. It also has good specificity and low sample consumption, which is expected to be a benefit for the CRP screening in early diagnosis of cardiovascular disease.

  5. In-situ etch rate study of Hf{sub x}La{sub y}O{sub z} in Cl{sub 2}/BCl{sub 3} plasmas using the quartz crystal microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Marchack, Nathan; Kim, Taeseung; Chang, Jane P., E-mail: jpchang@seas.ucla.edu [Department of Chemical and Biomolecular Engineering, University of California, Los Angeles, California 90095 (United States); Blom, Hans-Olof [Ångström Laboratory, Uppsala University, P.O. Box 534, SE-751 21 Uppsala (Sweden)

    2015-05-15

    The etch rate of Hf{sub x}La{sub y}O{sub z} films in Cl{sub 2}/BCl{sub 3} plasmas was measured in-situ in an inductively coupled plasma reactor using a quartz crystal microbalance and corroborated by cross-sectional SEM measurements. The etch rate depended on the ion energy as well as the plasma chemistry. In contrast to other Hf-based ternary oxides, the etch rate of Hf{sub x}La{sub y}O{sub z} films was higher in Cl{sub 2} than in BCl{sub 3}. In the etching of Hf{sub 0.25}La{sub 0.12}O{sub 0.63}, Hf appeared to be preferentially removed in Cl{sub 2} plasmas, per surface compositional analysis by x-ray photoelectron spectroscopy and the detection of HfCl{sub 3} generation in mass spectroscopy. These findings were consistent with the higher etch rate of Hf{sub 0.25}La{sub 0.12}O{sub 0.63} than that of La{sub 2}O{sub 3}.

  6. APPLICATION OF QUARTZ CRYSTAL MICROBALANCE IN ATMOSPHERIC CORROSION INVESTIGATION%石英晶体微天平(QCM)在大气腐蚀研究中的应用

    Institute of Scientific and Technical Information of China (English)

    严川伟; 曹楚南; 林海潮

    2001-01-01

    石英晶体微天平(QCM)作为一种高灵敏度的质量检测手段,已经用于金属材料大气腐蚀动力学及其环境因素和缓蚀剂存在的影响规律的研究,对QCM在大气腐蚀研究中的应用进行了综述.%The application of quartz crystal microbalance (QCM) in the study of atmospheric corrosion is reviewed. QCM is available to measure mass changes of a nanngram order and has widely been used for in-situ investigations of atmospheric corrosion. The effects of environmental factors,corrosive gas constituents and gas-phase inhibitors on the atmospheric corrosion mechanism of metal materials have been studied with QCM. In the recent years, the atmospheric corrosivity probe based on QCM techniques has been developed. The characteristics and developing trend of QCM for atmospheric corrosion investigation and monitoring are analyzed and discussed

  7. pH- and Electro-Responsive Properties of Poly(acrylic acid) and Poly(acrylic acid)-block-poly(acrylic acid-grad-styrene) Brushes Studied by Quartz Crystal Microbalance with Dissipation Monitoring.

    Science.gov (United States)

    Borisova, O V; Billon, L; Richter, R P; Reimhult, E; Borisov, O V

    2015-07-14

    We report on the synthesis of novel pH- and electro-responsive polyelectrolyte brushes from a gold substrate by direct one-step nitroxide-mediated polymerization of acrylic acid (AA) or copolymerization of AA and styrene (S). In the latter case, amphiphilic brushes of block-gradient copolymers PAA-b-(PAA-grad-PS) comprising one PAA block and one block with the gradient sequence of AA and S were obtained. The block-gradient copolymers are initiated from the surface by the start of the PAA block. The brushes were characterized by XPS and ellipsometry. (1)H NMR confirmed the gradient sequence of the PAA-grad-PS copolymer block. The pH- and electro-responsive properties of the brushes were studied by quartz crystal microbalance with dissipation monitoring (QCM-D) in combination with electrochemistry. This method provides evidence of swelling of the PAA brushes proportional to the contour length of the chains at elevated pH, whereas the response functions of the block-gradient copolymers are more complex and point to intermolecular aggregation in the brush at low pH. Monitoring of the changes in resonance frequency and dissipation of the QCM-D also demonstrates that application of negative voltage to the substrate leads to swelling of the brush; application of a positive voltage provokes only a transient collapse of the brush in proportion to the applied voltage.

  8. Quartz crystal growth

    Science.gov (United States)

    Baughman, Richard J.

    1992-01-01

    A process for growing single crystals from an amorphous substance that can undergo phase transformation to the crystalline state in an appropriate solvent. The process is carried out in an autoclave having a lower dissolution zone and an upper crystallization zone between which a temperature differential (.DELTA.T) is maintained at all times. The apparatus loaded with the substance, solvent, and seed crystals is heated slowly maintaining a very low .DELTA.T between the warmer lower zone and cooler upper zone until the amorphous substance is transformed to the crystalline state in the lower zone. The heating rate is then increased to maintain a large .DELTA.T sufficient to increase material transport between the zones and rapid crystallization. .alpha.-Quartz single crystal can thus be made from fused quartz in caustic solvent by heating to 350.degree. C. stepwise with a .DELTA.T of 0.25.degree.-3.degree. C., increasing the .DELTA.T to about 50.degree. C. after the fused quartz has crystallized, and maintaining these conditions until crystal growth in the upper zone is completed.

  9. Quartz Microbalance Sensor for the Detection of Acrylamide

    Directory of Open Access Journals (Sweden)

    Christoph A. Schalley

    2004-10-01

    Full Text Available Abstract: Several macrocycles of the Hunter-Vögtle type have been identified as superior host compounds for the detection of small amounts of acrylamide. When coated onto the surface of a quartz microbalance, these compounds serve as highly sensitive and selective sensor-active layers for their use in electronic noses. In this study, differently substituted macrocycles were investigated including an open-chain analogue and a catenane. Their structure and functional groups are correlated with their observed affinities to acrylamide and related acids and amides. The much smaller response of the open-chain compound and the almost absent sensor response of the catenane suggest that binding occurs within the cavity of the macrocycle. Theoretical calculations agree well with the experimental data even though they do not yet take into account the arrangement of the macrocycles in the sensor-active layer. The lower detection limit of acrylamide is 10 parts per billion (ppb, which is impressively low for this type of sensor. Other related compounds such as acrylic acid, propionamide, or propionic acid show no or significantly lower affinities to the macrocycles in these concentration ranges.

  10. In Situ Adsorption Studies at the Solid/Liquid Interface:Characterization of Biological Surfaces and Interfaces Using SumFrequency Generation Vibrational Spectroscopy, Atomic Force Microscopy,and Quartz Crystal Microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, Diana Christine [Univ. of California, Berkeley, CA (United States)

    2006-01-01

    Sum frequency generation (SFG) vibrational spectroscopy, atomic force microscopy (AFM), and quartz crystal microbalance (QCM) have been used to study the molecular surface structure, surface topography and mechanical properties, and quantitative adsorbed amount of biological molecules at the solid-liquid interface. The molecular-level behavior of designed peptides adsorbed on hydrophobic polystyrene and hydrophilic silica substrates has been examined as a model of protein adsorption on polymeric biomaterial surfaces. Proteins are such large and complex molecules that it is difficult to identify the features in their structure that lead to adsorption and interaction with solid surfaces. Designed peptides which possess secondary structure provide simple model systems for understanding protein adsorption. Depending on the amino acid sequence of a peptide, different secondary structures (α-helix and β-sheet) can be induced at apolar (air/liquid or air/solid) interfaces. Having a well-defined secondary structure allows experiments to be carried out under controlled conditions, where it is possible to investigate the affects of peptide amino acid sequence and chain length, concentration, buffering effects, etc. on adsorbed peptide structure. The experiments presented in this dissertation demonstrate that SFG vibrational spectroscopy can be used to directly probe the interaction of adsorbing biomolecules with a surface or interface. The use of well designed model systems aided in isolation of the SFG signal of the adsorbing species, and showed that surface functional groups of the substrate are sensitive to surface adsorbates. The complementary techniques of AFM and QCM allowed for deconvolution of the effects of surface topography and coverage from the observed SFG spectra. Initial studies of biologically relevant surfaces are also presented: SFG spectroscopy was used to study the surface composition of common soil bacteria for use in bioremediation of nuclear waste.

  11. “固化水层”模型拓展石英晶体微天平的应用%Applications of Quartz Crystal Microbalance with Solidified Liquid Layer Model

    Institute of Scientific and Technical Information of China (English)

    顾莉娟; 汪杰; 马宏伟

    2013-01-01

    Quartz crystal microbalance (QCM) has many advantages in research,but the data interpretation has hindered its applications in many research fields,especially for application in liquid.Recently,we proposed'solidified liquid layer' (SLL) model to simplify the data analysis.In this article,some missing evidences are provided to demonstrate the SLL model.The thickness result from ellipsometry accords with the result from the SLL model.The SLL model predicts that 1 Hz signal respond to a 0.18-nm change of TSLL,which greatly improve the resolution of QCMs in liquid.These researches effectively improve our understanding in the nature of Au—S bond breakage and its breakage process.Our results show that the SLL model will improve the applications of QCM in many fields.%石英晶体微天平(QCM)在液态环境下的应用一直由于数据分析复杂而受到限制.最近,我们提出了“固化水层”模型(SLL)以简化QCM数据分析过程.本文进一步提供了SLL模型的有关数据.根据SLL模型,1 Hz QCM频率信号对应于0.18 nm SLL层厚度的变化,而大多数商业的QCM均可以达到该精度.因此,根据SLL模型设计的检测方案将具有很高的灵敏度.QCM作为生物传感器的应用也得以拓展,可以相信SLL模型将大大增强QCM的分析能力.

  12. Development of a rubber elongation factor, surface-imprinted polymer-quartz crystal microbalance sensor, for quantitative determination of Hev b1 rubber latex allergens present in natural rubber latex products.

    Science.gov (United States)

    Sontimuang, Chonlatid; Suedee, Roongnapa; Canyuk, Bhutorn; Phadoongsombut, Narubodee; Dickert, Franz L

    2011-02-21

    Molecularly imprinted polymers (MIPs) for screening to detect rubber latex allergens (Hev b1) in natural rubber based products were designed as artificial recognition polymeric materials coated onto a quartz crystal microbalance (QCM). The polymers were prepared using a stamp imprinting procedure after mixing optimum amounts of methacrylic acid-vinylpyrrolidone-dihydroxyethylene bisacrylamide and Hev b1 latex allergen proteins, obtained from rubber gloves. QCM measurements showed that the resulting polymer layers after removal of the proteins used in their preparation could incorporate structures and features down to nanometer scale of protein templates into the imprinted polymer much better than a non-specific control polymer under controlled sensor conditions and an optimized polymerization process. This selective polymer but not the non-selective polymer clearly distinguished between the latex allergen Hev b1 and proteins such as lysozyme, ovalbumin and bovine serum albumin, with a selectivity factor of from 2 to 4, and the response of the rubber elongation factors by an astonishing factor of 12. The imprinted cavities recognized specific binding sites and could distinguish among related hevein latex allergenic proteins isolated from fresh natural rubber latex; Hev b1, Hev b2, and Hev b3 with a selectivity factor of from 4 to 6. The different QCM measurements obtained presumably reflected slightly different conformations and affinities to the MIP binding sites. The sensor layers selectively adsorbed Hev b1 within minutes in amounts ranging from 10 to 1500 μg L⁻¹ and with a detection limit of 1 μg L⁻¹. This work has demonstrated that this new sensor provides a fast and reliable response to natural rubber latex protein, even after being extracted from the matrix of rubber gloves.

  13. Quartz Crystal Microbalance with Dissipation Monitoring

    Science.gov (United States)

    2014-11-06

    immobilized onto the gold sensor in citric buffer (pH = 4), rinsed and washed subsequently in cycles of citric buffer (pH = 4) and PBS buffer (pH...dissipation (tougher) at acidic pH, with excellent reversibility up to five cycles . At pH = 7.4, a higher dissipation was observed in the triblock...CcE20Cc (Figure 2) was engineered with a long glutamic acid (Glu)-abundant E20 block (red, containing 40 mol % of Glu) in the middle and joined at

  14. An Exploration of the Metal Dependent Selectivity of a Metalloporphyrins Coated Quartz Microbalances Array

    Directory of Open Access Journals (Sweden)

    Alexandro Catini

    2016-10-01

    Full Text Available Several studies in the last two decades have demonstrated that metalloporphyrins coated quartz microbalances can be fruitfully used in many diverse applications, spanning from medical diagnosis to environmental control. This large versatility is due to the combination of the flexibility of metalloporphyrins molecular design with the independence of the quartz microbalance signal from the interaction mechanisms. The nature of the metal atom in the metalloporphyrins is often indicated as one of the most effective tools to design differently selective sensors. However, the properties of sensors are also strongly affected by the characteristics of the transducer. In this paper, the role of the metal atom is investigated studying the response, to various volatile compounds, of six quartz microbalance sensors that are based on the same porphyrin but with different metals. Results show that, since quartz microbalances (QMB transducers can sense all the interactions between porphyrin and volatile compounds, the metal ion does not completely determine the sensor behaviour. Rather, the sensors based on the same molecular ring but with different metal ions show a non-negligible common behaviour. However, even if limited, the different metals still confer peculiar properties to the sensors and might drive the sensor array identification of the pool of tested volatile compounds.

  15. An Exploration of the Metal Dependent Selectivity of a Metalloporphyrins Coated Quartz Microbalances Array

    Science.gov (United States)

    Catini, Alexandro; Kumar, Raj; Capuano, Rosamaria; Martinelli, Eugenio; Paolesse, Roberto; di Natale, Corrado

    2016-01-01

    Several studies in the last two decades have demonstrated that metalloporphyrins coated quartz microbalances can be fruitfully used in many diverse applications, spanning from medical diagnosis to environmental control. This large versatility is due to the combination of the flexibility of metalloporphyrins molecular design with the independence of the quartz microbalance signal from the interaction mechanisms. The nature of the metal atom in the metalloporphyrins is often indicated as one of the most effective tools to design differently selective sensors. However, the properties of sensors are also strongly affected by the characteristics of the transducer. In this paper, the role of the metal atom is investigated studying the response, to various volatile compounds, of six quartz microbalance sensors that are based on the same porphyrin but with different metals. Results show that, since quartz microbalances (QMB) transducers can sense all the interactions between porphyrin and volatile compounds, the metal ion does not completely determine the sensor behaviour. Rather, the sensors based on the same molecular ring but with different metal ions show a non negligible common behaviour. However, even if limited, the different metals still confer peculiar properties to the sensors and might drive the sensor array identification of the pool of tested volatile compounds. PMID:27782032

  16. Electrochemical characterization of electrolytes and electrodes for lithium-ion batteries. Development of a new measuring method for electrochemical investigations on electrodes with the electrochemical quartz crystal microbalance (EQCM); Elektrochemische Charakterisierung von Elektrolyten und Elektroden fuer Lithium-Ionen-Batterien. Entwicklung einer neuen Messmethode fuer elektrochemische Untersuchungen an Elektroden mit der EQCM

    Energy Technology Data Exchange (ETDEWEB)

    Moosbauer, Dominik Johann

    2010-11-09

    In this work the conductivities of four different lithium salts, LiPF6, LiBF4, LiDFOB, and LiBOB in the solvent mixture EC/DEC (3/7) were investigated. Furthermore, the influence of eight ionic liquids (ILs) as additives on the conductivity and electrochemical stability of lithium salt-based electrolytes was studied. The investigated salts were the well-known lithium LiPF6 and LiDFOB. Conductivity studies were performed over the temperature range (238.15 to 333.15) K. The electrochemical stabilities of the solutions were determined at aluminum electrodes. The salt solubility of LiBF4 and LiDFOB in EC/DEC (3/7) was measured with the quartz crystal microbalance (QCM), a method developed in our group. Moreover, a method to investigate interactions between the electrolyte and electrode components with the electrochemical quartz crystal microbalance (EQCM) was developed. First, investigations of corrosion and passivation effects on aluminum with different lithium salts were performed and masses of deposited products estimated. Therefore, the quartzes were specially prepared with foils. Active materials of cathodes, in this work lithium iron phosphate (LiFePO4), were also investigated with the EQCM by a new method. [German] In dieser Arbeit wurden die Leitfaehigkeiten von vier unterschiedlichen Salzen, LiPF6, LiBF4, LiDFOB und LiBOB in dem Loesemittelgemisch EC/DEC (3/7) untersucht. Des Weiteren wurde der Einfluss von acht Ionischen Fluessigkeiten (ILs) als Additive fuer Lithium-Elektrolyte auf die elektrochemische Stabilitaet und die Leitfaehigkeit studiert. Die untersuchten Salze waren LiPF6 und LiDFOB. Die Leitfaehigkeitsmessungen wurden in einem Temperaturbereich von (238,15 bis 333,15) K durchgefuehrt. Die elektrochemischen Stabilitaeten der Elektrolyte fanden an Aluminium statt. Mit einer an der Arbeitsgruppe entwickelten neuen Methode wurden zudem die Salzloeslichkeiten von LiBF4 und LiDFOB in EC/DEC (3/7) mit der Quarzmikrowaage (QCM) bestimmt. Weiterhin wurden

  17. Quartz Microbalance Study of 400-angstrom Thick Films near the lambda Point

    Science.gov (United States)

    Chan, Moses H. W.

    2003-01-01

    In a recent measurement we observed the thinning of an adsorbed helium film induced by the confinement of critical fluctuations a few millikelvin below the lambda point. A capacitor set-up was used to measure this Casimir effect. In this poster we will present our measurement of an adsorbed helium film of 400 angstroms near the lambda point with a quartz microbalance. For films this thick, we must take into account the non-linear dynamics of the shear waves in the fluid. In spite of the added complications, we were able to confirm the thinning of the film due to the Casimir effect and the onset of the superfluid transition. In addition, we observe a sharp anomaly at the bulk lambda point, most likely related to critical dissipation of the first sound. This work is carried out in collaboration with Rafael Garcia, Stephen Jordon and John Lazzaretti. This work is funded by NASA's Office of Biological and Physical Research under grant.

  18. Measurement of Total Condensation on a Shrouded Cryogenic Surface using a Single Quart Crystal Microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Haid, B J; Malsbury, T N; Gibson, C R; Warren, C T

    2008-06-10

    A single quartz crystal microbalance (QCM) is cooled to 18 K to measure condensation rates inside of a retractable ''shroud'' enclosure. The shroud is of a design intended to minimize condensate on fusion targets to be fielded at the National Ignition Facility (NIF). The shroud has a double-wall construction with an inner wall that may be cooled to 75-100 K. The QCM and the shroud system were mounted in a vacuum chamber and cooled using a cryocooler. Condensation rates were measured at various vacuum levels and compositions, and with the shroud open or closed. A technique for measuring total condensate during the cooldown of the system with an accuracy of better than 1.0 x 10{sup -6} g/cm{sup 2} was also demonstrated. The technique involved a separate measurement of the condensate-free crystal frequency as a function of temperature that was later applied to the measurement of interest.

  19. Note: Accurate determination of thickness of multiple layers of thin film deposited on a piezoelectric quartz crystal.

    Science.gov (United States)

    Wajid, Abdul

    2013-10-01

    Modern day piezoelectric quartz crystal microbalances for thin film deposition control are based on Z-match equation, which is mathematically valid for deposition of a single material on a given quartz crystal. When multiple layers are deposited, thickness and deposition rate errors accumulate due to mismatch of acoustic impedance of different materials. Here we present a novel method, based on the acoustic transfer matrix formalism, for accurate determination of thickness of an arbitrary number of layers of dissimilar materials deposited on a quartz crystal. Laboratory data show excellent accuracy of the method compared to conventional Z-match equation.

  20. Mechanical twinning in small quartz crystals

    Science.gov (United States)

    Laughner, J. W.; Newnham, R. E.; Cross, L. E.

    1982-02-01

    Quartz is known to be ferrobielastic; that is, quartz crystals have domain states (Dauphiné twins) which differ in their elastic compliance values and which can be switched by an appropriately oriented stress. Polycrystalline quartz has also been reported (Tullis 1970) to show preferential orientation of these domains following application of large uniaxial stresses. These experiments were designed to study twinning of synthetic quartz “grains” (minimum size 0.07×0.07×0.02 cm) in specially-constructed composites and of grains in three natural quartz aggregates — a quartzite, a novaculite, and a jasper. Backreflection X-ray techniques were used to verify twinning in the composite grains, while special electroding and electrical detection allowed the twinning processes to be examined in “real time.” Small synthetic quartz crystals were found to behave identically to the massive samples previously studied. Electrical pulses due to the reversal of piezoelectric coefficient d 11 in twinned quartz were detected from quartzite and from the man-made composites. Novaculite also gave electrical pulses which were probably from twinning (evidenced by the correlation of expected and observed pulse sizes and shapes), while no pulses from the jaspers indicative of twinning were detected. Grain size distribution differences are considered the main structural reason for the different behaviors.

  1. Quartz Crystal Microbalance Studies of Electrochemical Growth of Conducting Polymers

    Science.gov (United States)

    1989-06-15

    National Meeting of the Electrochemical Society , Hollywood, Florida, 1989 Corrosion Research Center Department of Chemical Engineering and Materials Science...176th Meeting of the Electrochemical Society , Extended Abstracts, October 1989 17COSATI CODES 18 SUBJECT TERMS (Continue an reverse it necesi4iy anid

  2. Molecularly Imprinted Quartz Crystal Microbalance Sensor (QCM for Bilirubin Detection

    Directory of Open Access Journals (Sweden)

    Çiğdem Çiçek

    2016-11-01

    Full Text Available This study aims the preparation of a QCM sensor for the detection of bilirubin in human plasma. Bilirubin-imprinted poly-(2-hydroxyethyl methacrylate-N-methacryloyl-l-tryptophan methyl ester (PHEMATrp nanofilm (MIP on the gold surface of a QCM chip was synthesized by the molecular imprinting technique. Meanwhile, the non-imprinted PHEMATrp (NIP nanofilm was synthesized by the same experimental technique to examine the imprinting effect. Characterization of MIP and NIP nanofilms on the QCM chip surface was achieved by atomic force microscopy (AFM, ellipsometry, Fourier transform infrared spectrophotometry-attenuated total reflectance (FTIR-ATR and contact angle measurements (CA. The observations indicated that the nanofilm was almost in a monolayer. Thereinafter, the imprinted and the non-imprinted QCM chips were connected to the QCM system to investigate kinetic and affinity properties. In order to examine the selectivity of the MIP-PHEMATrp nanofilm, competitive adsorption of bilirubin with cholesterol and estradiol was performed. Limit of detection (LOD and limit of quantitation (LOQ values were calculated as 0.45 μg/mL and 0.9 μg/mL, respectively.

  3. A dibutyl phthalate sensor based on a nanofiber polyaniline coated quartz crystal monitor.

    Science.gov (United States)

    Wang, You; Ding, Pengfei; Hu, Ruifen; Zhang, Jianming; Ma, Xingfa; Luo, Zhiyuan; Li, Guang

    2013-03-18

    Dibutyl phthalate (DBP) is a commonly used plasticizer and additive to adhesives, printing inks and nail polishes. Because it has been found to be a powerful reproductive and developmental toxicant, a sensor to monitor DBP in some working spaces and the environment is required. In this work polyaniline nanofibers were deposited on the electrode of a quartz crystal oscillator to form a Quartz Crystal Microbalance gas sensor. The coated quartz crystal and a non-coated quartz crystal were mounted in a sealed chamber, and their frequency difference was monitored. When DBP vapor was injected into the chamber, gas adsorption decreased the frequency of the coated quartz crystal oscillator and thereby caused an increase in the frequency difference between the two crystals. The change of the frequency difference was recorded as the sensor response. The sensor was extremely sensitive to DBP and could be easily recovered by N2 purging. A low measurement limit of 20 ppb was achieved. The morphologies of the polyaniline films prepared by different approaches have been studied by SEM and BET. How the nanofiber-structure can improve the sensitivity and stability is discussed, while its selectivity and long-term stability were investigated.

  4. Quartz Crystal Microbalance and Atomic Force Microscopy for Study of Carbohydrate-sensitive Multilayers Composed of Pheylboronic Acid Polymers%石英晶体微天平和原子力显微镜识别糖类化合物的苯硼酸接枝聚合物多层薄膜

    Institute of Scientific and Technical Information of China (English)

    袁文静; 钟彤; 闫晶; 薛中原; 齐伟; 王桦

    2015-01-01

    硼酸受体识别体系近年来被广泛用于糖的分子识别研究,硼酸在一定酸度条件下,可特异性结合含顺式邻位多羟基的物质(如二醇、糖等)。本实验利用EDC/NHS化学交联,3-氨基苯硼酸( APBA)与聚丙烯酸( PAA)反应,制得苯硼酸接枝的聚合物PAA-PBA,进而将此聚合物进行层层组装,获得苯硼酸功能化薄膜。利用石英晶体微天平( QCM)和原子力显微镜( AFM)分别从宏观和微观的角度监测分析了此薄膜表面对糖类化合物的识别性质。结果表明此类薄膜对一定浓度(>50μg/mL)的糖类化合物均能表现出明显识别,其中,对果糖识别最为明显。此体系抗干扰性好,可重复使用,长期保存后仍能较好保持性能。微观表面形貌观察发现糖类化合物在薄膜表面识别均匀,识别后薄膜表面粗糙度发生明显变化。本研究成果可望用于开发高选择性、高灵敏度的糖识别体系。%Boronic acids and their derivatives have been widely used in carbohydrate-sensitive materials because they can selectively bind 1,2-and 1,3-diol compounds, including sugars, to form cyclic boronate esters. In this work, pheylboronic acid ( PBA) moieties were grafted onto the backbone of poly( acrylic acid) ( PAA) through the condensation reaction between aminopheyl-boronic acid and carboxylic acid group of PAA in the presence of EDC/NHS, designed as PAA-PBA. Then the resulting PAA-PBA were assembled with poly ( ethyleneimine) ( PEI) to form PAA-PBA multilayer films. The sensing performance of the PEI/PAA-PBA film to carbohydrate (> 50 μg/mL ) , including glucose, fructose, mannose and galactose, has been investigated by combination of the complementary techniques of quartz crystal microbalance ( QCM ) and atomic force microscopy ( AFM) . It was demonstrated that the multilayer showed higher sensitivity to fructose than glucose, mannose and galactose. The interferences of ascorbic acid, uric acid and dopamine to the

  5. Modeling by regression for laser cutting of quartz crystal

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Presents the theoretical models built by analysis of the mechanism of laser cutting of quartz crystal and re gression of test results for the laser cutting of quartz crystal, and comparative analysis of calculation errors for these models, and concludes with test results that these models comprehensively reflect the physical features of laser cutting of quartz crystal and satisfy the industrial production requirements, and they can be used to select right parameters for improvement of productivity and quality and saving of energy.

  6. Potential-dependent adsorption/desorption behavior of perfluorosulfonated ionomer on a gold electrode surface studied by cyclic voltammetry, electrochemical quartz microbalance, and electrochemical atomic force microscopy.

    Science.gov (United States)

    Masuda, Takuya; Ikeda, Kota; Uosaki, Kohei

    2013-02-19

    Potential-dependent adsorption/desorption behavior of perfluorosulfonated ionomer (PFSI) on a gold electrode was investigated by cyclic voltammetry (CV), electrochemical quartz crystal microbalance (EQCM), and electrochemical atomic force microscopy (EC-AFM) in a Nafion (i.e., PFSI) dispersed aqueous solution without any other electrolyte. It was found that PFSI serves as an electrolyte and that electrochemical measurements can be performed in this solution without any significant IR drop. PFSI molecules were adsorbed on the Au surface in the lying-down configuration in the potential range between 0 and 0.45 V, the amount of adsorbed PFSI increased when the potential was made more positive than 0.75 V, and the adsorbed PFSI fully desorbed from the surface at potentials more positive than 1.4 V where gold oxide was formed. Once the gold oxide had been reduced, PFSI readsorbed on the surface, albeit slowly. PFSI desorbed from the surface as the potential was made more negative than 0 V. These processes took place reversibly.

  7. Adsorption Device Based on a Langatate Crystal Microbalance for High Temperature High Pressure Gas Adsorption in Zeolite H-ZSM-5.

    Science.gov (United States)

    Ding, Wenjin; Baracchini, Giulia; Klumpp, Michael; Schwieger, Wilhelm; Dittmeyer, Roland

    2016-08-25

    We present a high-temperature and high-pressure gas adsorption measurement device based on a high-frequency oscillating microbalance (5 MHz langatate crystal microbalance, LCM) and its use for gas adsorption measurements in zeolite H-ZSM-5. Prior to the adsorption measurements, zeolite H-ZSM-5 crystals were synthesized on the gold electrode in the center of the LCM, without covering the connection points of the gold electrodes to the oscillator, by the steam-assisted crystallization (SAC) method, so that the zeolite crystals remain attached to the oscillating microbalance while keeping good electroconductivity of the LCM during the adsorption measurements. Compared to a conventional quartz crystal microbalance (QCM) which is limited to temperatures below 80 °C, the LCM can realize the adsorption measurements in principle at temperatures as high as 200-300 °C (i.e., at or close to the reaction temperature of the target application of one-stage DME synthesis from the synthesis gas), owing to the absence of crystalline-phase transitions up to its melting point (1,470 °C). The system was applied to investigate the adsorption of CO2, H2O, methanol and dimethyl ether (DME), each in the gas phase, on zeolite H-ZSM-5 in the temperature and pressure range of 50-150 °C and 0-18 bar, respectively. The results showed that the adsorption isotherms of these gases in H-ZSM-5 can be well fitted by Langmuir-type adsorption isotherms. Furthermore, the determined adsorption parameters, i.e., adsorption capacities, adsorption enthalpies, and adsorption entropies, compare well to literature data. In this work, the results for CO2 are shown as an example.

  8. Mineral resource of the month: cultured quartz crystal

    Science.gov (United States)

    ,

    2008-01-01

    The article presents information on cultured quartz crystals, a mineral used in mobile phones, computers, clocks and other devices controlled by digital circuits. Cultured quartz, which is synthetically produced in large pressurized vessels known as autoclaves, is useful in electronic circuits for precise filtration, frequency control and timing for consumer and military use. Several ingredients are used in producing cultured quartz, including seed crystals, lascas, a solution of sodium hydroxide or sodium carbonate, lithium salts and deionized water.

  9. The Characteristics of the Shear-Vibrating Quartz Crystal Resonator

    Institute of Scientific and Technical Information of China (English)

    Wenjie Tian; Lingling Liu; Junling Lu; Fuxue Zhang

    2006-01-01

    According to the piezoelectric equation and the vibration theory of the quartz crystal, the relations between the vibrating frequency and structural parameters under the thickness-shear-vibration of AT-cut quartz crystal have been studied.The frequency conditions under which quartz crystal resonator formed stationary wave inside the electrode district and the transmission characteristics of wave outside the electrode district have also been discussed. A quartz crystal resonator was developed based on this analysis. The experiment showed that the force-sensing characteristics were independent of the fixation of the crystal edge. The detecting distinguish ability was up to 0.001 °, and the short-term frequency stability was up to 1.38x 10-10/min.

  10. Basic characteristics of quartz crystal sensor with interdigitated electrodes

    Directory of Open Access Journals (Sweden)

    Hiroshi Muramatsu

    2016-03-01

    Full Text Available This paper describes basic characteristics of the quartz crystal sensor with interdigitated electrodes (IDE quartz crystal sensor which is for simultaneous monitoring of mass, viscosity, conductivity and dielectric changes of liquids or thin films. As the IDE quartz crystal sensor has three terminals for a pair of IDEs on the one side and a counter electrode on the other side, the resonance properties have been analyzed using the electrical equivalent circuit models and measured experimentally for all connecting types of electrode pairs. The IDE quartz crystal has shown clear resonance curves for calculating the resonance frequency and resonance resistance values as well as normal quartz crystal in the air and in contact with liquid. Small shifts in the resonance frequency and resonance resistance depending on the connecting types have been obtained and analyzed using the equivalent circuit models. We have found the integrated quartz crystal and IDE sensors could be monitored simultaneously by only one impedance analyzer. Finally, two types of measuring systems have been demonstrated for continuous measuring methods.

  11. Water weakening in experimentally deformed milky quartz single crystals

    Science.gov (United States)

    Stunitz, H.; Thust, A.; Kilian, R.; Heilbronner, R.; Behrens, H.; Tarantola, A.; Fitz Gerald, J. D.

    2015-12-01

    Natural single crystals of quartz have been experimentally deformed in two orientations: (1) normal to one prism-plane, (2) In O+ orientation at temperatures of 900 and 1000°C, pressures of 1.0 and 1.5 GPa, and strain rates of ~1 x 10-6s-1. The starting material is milky quartz, consisting of dry quartz (H2O contents of recycling of H2O between FI´s, dislocation generation at very small fluid inclusions, incorporation of structurally bound H into dislocation cores, and release of H2O from dislocations back into FI´s during recovery. Cracking and crack healing play an important role in the recycling process and imply a close interrelationship between brittle and crystal plastic deformation. The H2O weakening by this process is of a disequilibrium nature and thus depends on the amount of H2O available.

  12. Quartz-like Crystals Found in Planetary Disks

    Science.gov (United States)

    2008-01-01

    NASA's Spitzer Space Telescope has, for the first time, detected tiny quartz-like crystals sprinkled in young planetary systems. The crystals, which are types of silica minerals called cristobalite and tridymite, can be seen close-up in the black-and-white insets (cristobalite is on the left, and tridymite on the right). The main picture is an artist's concept of a young star and its swirling disk of planet-forming materials. Cristobalite and tridymite are thought to be two of many planet ingredients. On Earth, they are normally found as tiny crystals in volcanic lava flows and meteorites from space. These minerals are both related to quartz. For example, if you were to heat the familiar quartz crystals often sold as mystical tokens, the quartz would transform into cristobalite and tridymite. Because cristobalite and tridymite require rapid heating and cooling to form, astronomers say they were most likely generated by shock waves traveling through the planetary disks. The insets are Scanning Electron Microscope pictures courtesy of George Rossman of the California Institute of Technology, Pasadena, Calif.

  13. Annealing Effect on Photovoltages of Quartz Single Crystals

    Institute of Scientific and Technical Information of China (English)

    TIAN Lu; ZHAO Song-Qing; ZHAO Kun

    2010-01-01

    @@ We investigate the photovoltaic effects of quartz single crystals annealed at high temperatures in ambient atmosphere.The open-circuit photovoltages and surface morphologies strongly depend on the heating treatments.When the annealing temperature increases from room temperature to 900℃,the rms roughness of quartz single crystal wafers increases from 0.207 to 1.011 nm.In addition,the photovoltages decrease from 1.994#V at room temperature to 1.551 μ V after treated at 500℃,and then increase up to 9.8μV after annealed at 900℃.The inner mechanism of the present photovoltaic response and surface morphologies is discussed.

  14. Using a titanium-in-quartz geothermometer for crystallization temperature estimation of the Palaeoproterozoic Suursaari quartz porphyry

    Directory of Open Access Journals (Sweden)

    Kairi Ehrlich

    2012-11-01

    Full Text Available The Suursaari volcanic sequence represents volcanic activity related to Wiborg Batholith rapakivi intrusions in the southern part of the Fennoscandian Shield. The estimated pressure conditions for batholith granitic rocks are 1–5 kbar and crystallization temperatures range from 670 to 890 °C. To describe the temperature regime of the Suursaari volcanic system, a rock sample was taken from the Mäkiinpäällys Mountain outcrop and analysed with laser ablation inductively coupled plasma mass spectrometry. Sample spots were selected from quartz phenocrysts and groundmass. Quartz crystallization temperatures were calculated by the Ti-in-quartz method that takes into account rutile equilibrium and Ti activity in each phase. The calculated crystallization temperatures of the Suursaari quartz porphyry are in the range of 647–738 °C. The results show that the Suursaari quartz porphyry contains two generations of quartz which can be distinguished on the basis of crystallization temperatures: phenocrysts crystallized at higher and groundmass quartz at lower temperature.

  15. Voltage-controlled narrowband and wide, variable-range four-segment quartz crystal oscillator.

    Science.gov (United States)

    Ruslan, Ruzaini; Satoh, Tomio; Akitsu, Tetsuya

    2012-03-01

    In this work, our goal is to develop a voltage-controlled variable-frequency quartz crystal oscillator with narrowband response, wide, variable frequency range and the capacity to oscillate across the series resonance frequency using a four-segment configuration of a quartz crystal oscillator. In conventional quartz oscillators, the quartz resonator is inserted in the feedback loop between the input and the output of the active circuit, providing sufficient gain and the phase relation. In the oscillator developed here, the quartz crystal resonator is inserted between the loop circuit and the ground potential. The performance of the voltage-controlled variable-frequency oscillator is demonstrated across the series resonance frequency.

  16. Measuring Enthalpy of Sublimation of Volatiles by Means of Piezoelectric Crystal Microbalances

    Science.gov (United States)

    Dirri, Fabrizio; Palomba, Ernesto; Longobardo, Andrea; Zampetti, Emiliano

    2016-09-01

    Piezoelectric Crystal Microbalances (PCM's) are widely used to study the chemical processes involving volatile compounds in any environment, such as condensation process. Since PCM's are miniaturized sensor, they are very suitable for planetary in situ missions, where can be used to detect and to measure the mass amount of astrobiologically significant compounds, such as water and organics. This work focuses on the realization and testing of a new experimental setup, able to characterize volatiles which can be found in a planetary environment. In particular the enthalpy of sublimation of some dicarboxylic acids has been measured. The importance of dicarboxylic acids in planetology and astrobiology is due to the fact that they have been detected in carbonaceous chondritic material (e.g. Murchinson), among the most pristine material present in our Solar System. In this work, a sample of acid was heated in an effusion cell up to its sublimation. For a set of temperatures (from 30 °C to 75 °C), the deposition rate on the PCM surface has been measured. From these measurements, it has been possible to infer the enthalpy of sublimation of Adipic acid, i.e. ΔH = 141.6 ± 0.8 kJ/mol and Succinic acid, i.e. ΔH = 113.3 ± 1.3 kJ/mol. This technique has so demonstrated to be a good choice to recognise a single compound or a mixture (with an analysis upstream) even if some improvements concerning the thermal stabilization of the system will be implemented in order to enhance the results' accuracy. The experiment has been performed in support of the VISTA (Volatile In Situ Thermogravimetry Analyzer) project, which is included in the scientific payload of the ESA MarcoPolo-R mission study.

  17. α-Amylase sensor based on the degradation of oligosaccharide hydrogel films monitored with a quartz crystal sensor.

    Science.gov (United States)

    Gibbs, Martin John; Biela, Anna; Krause, Steffi

    2015-05-15

    α-Amylase hydrolyses starch molecules to produce smaller oligosaccharides and sugars. Amylases are of great importance in biotechnology and find application in fermentation, detergents, food and the paper industry. The measurement of α-amylase activity in serum and urine has been used in the diagnosis of acute pancreatitis. Salivary amylase has also been shown to be a stress indicator. Sensor coatings suitable for the detection of α-amylase activity have been developed. Oligosaccharides such as glycogen and amylopectin were spin-coated onto gold coated quartz crystals with a base frequency of 10 MHz. The films were subsequently cross-linked with hexamethylene diisocyanate. Film degradation was monitored with a quartz crystal microbalance (QCM) and electrochemical impedance measurements. The films were shown to be stable in phosphate buffered saline (PBS). Addition of α-amylase to the solution resulted in the rapid degradation of the films. The maximum rate of degradation was found to be strongly dependent on the amylase activity in the range typically found in serum when diagnosing pancreatitis (0.08-8 U/ml). Sensor responses in serum were found to be very similar to those obtained in buffer indicating the absence of non-specific binding. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Chemically Selective Coated Quartz Crystal Microbalance (QCM) Array for Detection of Volatile Organic Chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Bohuszewicz, T.V.; Frye-Mason, G.C.; Martin, S.J.; Osbourn, G.C. Bartholomew, J.W.; Schneider, T.W.; Spates, J.J.

    1998-11-04

    Liquid flow cells have been fabricated to prepare an array of QCMS operating simultaneously for detection and identification of VOCS in water. TWO signals, a tlequency response and a damping voltage response, were obtained per resonator. A blank QCM was used as a reference to account for changes in liquid density and viscosity. Nine different polymer coatings applied using a spin coat technique have been examined for VOC response under liquid flow conditions. A matrix of three classes of VOCS were examined for each coating with four chemicals in each class. The three classes of VOCS are polar, nonpolar and chlorinated. A pattern recognition technique, called visually empirical region of influence (VERI), was used to cluster the responses in n-dimensional space. Chemicals within a class varying by only one methyl group (e.g., toluene and xylene) are easily discriminated using only two different coatings with three different QCM responses. All chemicak were easily separated and detected with a total of 5 films and 6 responses with >99% accuracy.

  19. Capacitive Behavior in Conducting Polymers: AC Impedance and Quartz Crystal Microbalance Studies

    Science.gov (United States)

    1989-06-15

    Extended Abstracts, 175th National Meeting of the Electrochemical Society , Los Angeles, California, 1989 Corrosion Research Center Department of Chemical...114. DATE OF REPORT (Vear,Montha) 15PAGE COUNT Technical I Rom 7/88 TO 619I 89/06/15I 16. SUPPLEMENTARY NOTATION 175th Meeting of the Electrochemical ... Society , Extended Abstracts, May 1989 17 COSATI CODES IS. SUBJECT TERMS (Continue in reverie if necessary and identify by block number) FIELD GROUP

  20. Hydrolysis of model cellulose films by cellulosomes: Extension of quartz crystal microbalance techniques to multienzymatic complexes

    Science.gov (United States)

    Clostridium thermocellum, a well-studied cellulolytic bacterium, produces highly active cellulases in the form of cellulosomes. The ability of the cellulose binding module within the cellulosome to adhere C. thermocellum cells to the cellulosic substrate is considered to contribute to its high cellu...

  1. The Laser Ablation of Gold Films at the Electrode Surface of a Quartz Crystal Microbalance

    Science.gov (United States)

    1993-05-01

    to the QCM was controlled via a manual shutter. The laser beam was focussed onto the electrode surface of the QCM with a 150 mm f.l. lens. Fluence...A. Cross, H, Dallaporta, S. Lazare, H. Hiraoka, N. Merk and W. Marine, Appl. Surf Sci. 54 (1992) 278. 12. S. Lazare and V. Granier, J. App/. Phys. 63

  2. Chemically selective coated quartz-crystal-microbalance (QCM) array for detection of volatile organic chemicals

    Science.gov (United States)

    Schneider, Thomas W.; Frye-Mason, Gregory C.; Martin, Stephen J.; Spates, James J.; Bohuszewicz, Teresa V.; Osbourn, Gordon C.; Bartholomew, John W.

    1998-12-01

    Liquid flow cells have been fabricated to prepare an array of QCMs operating simultaneously for detection and identification of VOCs in water. Two signals, a frequency response and a damping voltage response, were obtained per resonator. A blank QCM was used as a reference to account for changes in liquid density and viscosity. Nine different polymer coatings applied using a spin coat technique have been examined for VOC response under liquid flow conditions. A matrix of three classes of VOCs were examined for each coating with four chemicals in each class. The three classes of VOCs are polar, nonpolar and chlorinated. A pattern recognition technique, called visually empirical region of influence, was used to cluster the responses in n- dimensional space. Chemicals within a class varying by only one methyl group (e.g., toluene and xylene) are easily discriminated using only two different coatings with three different QCM responses. All chemicals were easily separated and detected with a total of 5 films and 6 responses with >99% accuracy.

  3. Exploring silver ionic liquids for reaction-based gas sensing on a quartz crystal microbalance.

    Science.gov (United States)

    Li, Hsin-Yi; Hsu, Tzu-Hsuan; Chen, Chien-Yuan; Tseng, Ming-Chung; Chu, Yen-Ho

    2015-09-21

    Reaction-based, sensitive sensing of aldehyde and ketone gases in real time was effectively achieved on QCM chips thin-coated with silver ionic liquids and , respectively. The method platform developed in this work involves straightforward synthesis of functional silver ionic liquids in water, and is label-free and highly chemoselective with superior gas reactivity for and and, most significantly, totally insensitive to moisture.

  4. Reaction-based azide gas sensing with tailored ionic liquids measured by quartz crystal microbalance.

    Science.gov (United States)

    Tseng, Ming-Chung; Chu, Yen-Ho

    2014-02-18

    On the basis of the strain-promoted [3 + 2] cycloaddition reaction performed at ambient temperature, a label-free, online, and chemospecific gas-phase measurement of organic azides in real time was efficiently achieved on QCM chips thin-coated with tailored ionic liquid TIL 1.

  5. Quartz Crystal Microbalance Studies Of Dimethyl Methylphosphonate Sorption Into Trisilanolphenyl-Poss Films

    Science.gov (United States)

    2006-11-06

    VX. GB and GD dissolve in water and, at pH values PO OH F P O F O C H H H P O F O C H H H + Sarin (GB) Methylphosphono- fluoridic acid Propylene 5...quantitatively determined the amount of DMMP adsorbed onto an alumina-supported iron and cerium oxide surface using FTIR.18,19 At 25 °C, the alumina...LB-film. This value is actually larger than the degradation capacity of alumina-supported iron and cerium oxide surfaces, reported to be 510 µmol of

  6. Fluid inclusions and microstructures in experimentally deformed quartz single crystals

    Science.gov (United States)

    Thust, A.; Tarantola, A.; Heilbronner, R.; Stünitz, H.

    2009-04-01

    The "H2O-weakening" effect that reduces the strength of quartz dramatically (e.g. Griggs & Blacic 1965) is still not understood. For example, Kronenberg & Tullis (1984) conclude that the weakening effect is pressure dependent while Paterson (1989) infers a glide and recovery control of water. Obviously, the spatial distribution and transport of H2O are important factors (Kronenberg et al. 1986, FitzGerald et al. 1991). We have carried out experiments on milky quartz in a Griggs deformation apparatus. Cylinders (6.5 mm in diameter, 12-13 mm in length) from a milky zone of a natural quartz single crystal have been cored in orientations (1) normal to one of the prism planes and (2) 45˚ to and 45˚ to (O+orientation). At 1 GPa confining pressure, 900˚ C and 10-6s-1, the flow strength is 150 MPa for samples with orientation (1). Further experiments are needed to establish the flow strength for orientation (2). FTIR measurements on double-polished thick sections (200-500 μm) in the undeformed quartz material yield an average H2O content of approximately 100 H/106Si. The water is heterogeneously distributed in the sample. Direct measurements on fluid inclusions yield a H2O content of more than 25 000 H/106Si. Thus, the H2O in the undeformed material is predominantly present in fluid inclusions of size from tens to hundred microns. Micro-thermometric measurements at low temperature indicate the presence of different salts in the fluid inclusions. The ice melting temperature, between -6.9 and -7.4˚ C, indicate an average salinity of 10.5 wt% NaCl. After deformation the distribution of H2O is more homogeneous throughout the sample. The majority of the big inclusions have disappeared and very small inclusions of several microns to sub-micron size have formed. FTIR measurements in zones of undulatory extinction and shear bands show an average H2O content of approximately 3000 H/106Si. Moreover, the larger fluid inclusions are characterized by a higher salinity (12 wt%) due

  7. Magneto-optic sensor based on electrogyration compensation and single-quartz crystal

    Science.gov (United States)

    Li, Changsheng; Cui, He; Zhang, Xuan

    2016-11-01

    Magnetooptic sensor based on electrogyration compensation is proposed and experimentally demonstrated by using single quartz crystal. The sensing unit is composed of single quartz crystal and two polarizers. Quartz crystal exhibits magneto-optic, electro-optic and electrogyration effects, thus magneto-optic Faraday rotation angle can be compensated by the electrogyration angle induced by the compensating voltage applied to the crystal. The compensating voltage is sensitive to both the deviation angle between light beam and principal crystalline axis, and the azimuth angle of polarizer. The 50Hz ac magnetic flux density within 267Gs has been measured, the compensating voltage is 0.72V/Gs for a single quartz crystal with a length of 23mm. The proposed sensor has potential application to closed-loop measurement of magnetic field.

  8. Timescales of Quartz Crystallization and the Longevity of the Bishop Giant Magma Body

    Energy Technology Data Exchange (ETDEWEB)

    Gualda, Guilherme A.R.; Pamukcu, Ayla S.; Ghiorso, Mark S.; Anderson, Jr. , Alfred T.; Sutton, Stephen R.; Rivers, Mark L. (OFM Res.); (Vanderbilt); (UC)

    2013-04-08

    Supereruptions violently transfer huge amounts (100 s-1000 s km{sup 3}) of magma to the surface in a matter of days and testify to the existence of giant pools of magma at depth. The longevity of these giant magma bodies is of significant scientific and societal interest. Radiometric data on whole rocks, glasses, feldspar and zircon crystals have been used to suggest that the Bishop Tuff giant magma body, which erupted {approx}760,000 years ago and created the Long Valley caldera (California), was long-lived (>100,000 years) and evolved rather slowly. In this work, we present four lines of evidence to constrain the timescales of crystallization of the Bishop magma body: (1) quartz residence times based on diffusional relaxation of Ti profiles, (2) quartz residence times based on the kinetics of faceting of melt inclusions, (3) quartz and feldspar crystallization times derived using quartz+feldspar crystal size distributions, and (4) timescales of cooling and crystallization based on thermodynamic and heat flow modeling. All of our estimates suggest quartz crystallization on timescales of <10,000 years, more typically within 500-3,000 years before eruption. We conclude that large-volume, crystal-poor magma bodies are ephemeral features that, once established, evolve on millennial timescales. We also suggest that zircon crystals, rather than recording the timescales of crystallization of a large pool of crystal-poor magma, record the extended periods of time necessary for maturation of the crust and establishment of these giant magma bodies.

  9. Timescales of quartz crystallization and the longevity of the Bishop giant magma body.

    Science.gov (United States)

    Gualda, Guilherme A R; Pamukcu, Ayla S; Ghiorso, Mark S; Anderson, Alfred T; Sutton, Stephen R; Rivers, Mark L

    2012-01-01

    Supereruptions violently transfer huge amounts (100 s-1000 s km(3)) of magma to the surface in a matter of days and testify to the existence of giant pools of magma at depth. The longevity of these giant magma bodies is of significant scientific and societal interest. Radiometric data on whole rocks, glasses, feldspar and zircon crystals have been used to suggest that the Bishop Tuff giant magma body, which erupted ~760,000 years ago and created the Long Valley caldera (California), was long-lived (>100,000 years) and evolved rather slowly. In this work, we present four lines of evidence to constrain the timescales of crystallization of the Bishop magma body: (1) quartz residence times based on diffusional relaxation of Ti profiles, (2) quartz residence times based on the kinetics of faceting of melt inclusions, (3) quartz and feldspar crystallization times derived using quartz+feldspar crystal size distributions, and (4) timescales of cooling and crystallization based on thermodynamic and heat flow modeling. All of our estimates suggest quartz crystallization on timescales of <10,000 years, more typically within 500-3,000 years before eruption. We conclude that large-volume, crystal-poor magma bodies are ephemeral features that, once established, evolve on millennial timescales. We also suggest that zircon crystals, rather than recording the timescales of crystallization of a large pool of crystal-poor magma, record the extended periods of time necessary for maturation of the crust and establishment of these giant magma bodies.

  10. The response of quartz crystals coated with thin fatty acid film to organic gases

    CERN Document Server

    Jin, C N; Kim, K H; Kwon, Y S

    1999-01-01

    We tried to apply a quartz crystal as a sensor by using the resonant frequency and the resistance properties of quartz crystals. Four kinds of fatty acids that have the same head groups were coated on the surfaces of the quartz crystals, and the shift of the resonant frequency and the resistance were observed based on the lengths of the tail groups. Myristic acid (C sub 1 sub 4), palmitic acid (C sub 1 sub 6), stearic acid (C sub 1 sub 8), and arachidic acid (C sub 2 sub 0) were deposited on the surfaces of quartz crystals by using the Langmuir-Blodgett (LB) method. As a result, the resonant frequency change was more sensitive to high molecular-weight fatty acids than to low molecular-weight ones. We also observed the effect of temperature on stearic acid LB films, and the response properties of quartz crystals coated with stearic-acid LB films to organic gases were investigated. As a result, the sensitivity of quartz crystals to organic gases was higher for higher molecular-weight gas, and we found that quar...

  11. Can enantiomorphic crystals like quartz play a role in the origin of homochirality on earth?

    Science.gov (United States)

    Klabunovskii, E I

    2001-01-01

    This communication reviews the possible actions of enantiomorphic crystals on the surface of Earth as sources of homochirality of organic compounds. The discovery of asymmetric adsorption and asymmetric catalysis involving optically active quartz crystals has led some authors to conclude that this source of asymmetry played an important role as a source of homochirality in nature, a concept that later proved erroneous. Moreover, data regarding the preponderance in nature of l-quartz crystals have been used to confirm calculations of the parity violation energy difference (PVED) for l-quartz and, hence, to explain the prevalence of L-amino acids and D-sugars in living matter. As discussed here, quartz and other enantiomorphs such as sodium chlorate can produce chiral intermediates active in autocatalytical processes. Our most recent compilation of the literature, however, reveals that the distribution of d- and l-quartz crystals at the surface of the Earth when all possible locations are included is quite random. Although quartz can serve as an effective asymmetric inductor in autocatalytic processes, it cannot be the source of homochirality of living matter because of the random occurrence of the two types of enantiomorphs. The calculations of PVED values for quartz therefore lack a sound physical basis.

  12. Greatly improved small inductance measurement using quartz crystal parasitic capacitance compensation.

    Science.gov (United States)

    Matko, Vojko; Jezernik, Karel

    2010-01-01

    Generally, quartz crystal inductance frequency pulling in oscillators is very low and therefore is not often used in practice. The new method of improving frequency pullability uses inductance to compensate for quartz stray capacitances. To this end, a special AT fundamental quartz crystal working near the antiresonance frequency is selected. By modifying its equivalent circuit with load inductance and series tuning capacitance, the magnetic sensing of the circuit can be highly improved. The experimental results show that the new approach using the quartz crystal stray capacitance compensation method increases the frequency pulling range (from ≅2 kHz/μH to ≅600 kHz/μH) by ×300 depending on the type of oscillator, making possible the measurement of nano-magnetic changes.

  13. High-Precision Hysteresis Sensing of the Quartz Crystal Inductance-to-Frequency Converter.

    Science.gov (United States)

    Matko, Vojko; Milanović, Miro

    2016-06-28

    A new method for the automated measurement of the hysteresis of the temperature-compensated inductance-to-frequency converter with a single quartz crystal is proposed. The new idea behind this method is a converter with two programmable analog switches enabling the automated measurement of the converter hysteresis, as well as the temperature compensation of the quartz crystal and any other circuit element. Also used is the programmable timing control device that allows the selection of different oscillating frequencies. In the proposed programmable method two different inductances connected in series to the quartz crystal are switched in a short time sequence, compensating the crystal's natural temperature characteristics (in the temperature range between 0 and 50 °C). The procedure allows for the measurement of the converter hysteresis at various values of capacitance connected in parallel with the quartz crystal for the converter sensitivity setting at selected inductance. It, furthermore, enables the measurement of hysteresis at various values of inductance at selected parallel capacitance (sensitivity) connected to the quartz crystal. The article shows that the proposed hysteresis measurement of the converter, which converts the inductance in the range between 95 and 100 μH to a frequency in the range between 1 and 200 kHz, has only 7 × 10(-13) frequency instability (during the temperature change between 0 and 50 °C) with a maximum 1 × 10(-11) hysteresis frequency difference.

  14. High-Precision Hysteresis Sensing of the Quartz Crystal Inductance-to-Frequency Converter

    Directory of Open Access Journals (Sweden)

    Vojko Matko

    2016-06-01

    Full Text Available A new method for the automated measurement of the hysteresis of the temperature-compensated inductance-to-frequency converter with a single quartz crystal is proposed. The new idea behind this method is a converter with two programmable analog switches enabling the automated measurement of the converter hysteresis, as well as the temperature compensation of the quartz crystal and any other circuit element. Also used is the programmable timing control device that allows the selection of different oscillating frequencies. In the proposed programmable method two different inductances connected in series to the quartz crystal are switched in a short time sequence, compensating the crystal’s natural temperature characteristics (in the temperature range between 0 and 50 °C. The procedure allows for the measurement of the converter hysteresis at various values of capacitance connected in parallel with the quartz crystal for the converter sensitivity setting at selected inductance. It, furthermore, enables the measurement of hysteresis at various values of inductance at selected parallel capacitance (sensitivity connected to the quartz crystal. The article shows that the proposed hysteresis measurement of the converter, which converts the inductance in the range between 95 and 100 μH to a frequency in the range between 1 and 200 kHz, has only 7 × 10−13 frequency instability (during the temperature change between 0 and 50 °C with a maximum 1 × 10−11 hysteresis frequency difference.

  15. High-Precision Hysteresis Sensing of the Quartz Crystal Inductance-to-Frequency Converter

    Science.gov (United States)

    Matko, Vojko; Milanović, Miro

    2016-01-01

    A new method for the automated measurement of the hysteresis of the temperature-compensated inductance-to-frequency converter with a single quartz crystal is proposed. The new idea behind this method is a converter with two programmable analog switches enabling the automated measurement of the converter hysteresis, as well as the temperature compensation of the quartz crystal and any other circuit element. Also used is the programmable timing control device that allows the selection of different oscillating frequencies. In the proposed programmable method two different inductances connected in series to the quartz crystal are switched in a short time sequence, compensating the crystal’s natural temperature characteristics (in the temperature range between 0 and 50 °C). The procedure allows for the measurement of the converter hysteresis at various values of capacitance connected in parallel with the quartz crystal for the converter sensitivity setting at selected inductance. It, furthermore, enables the measurement of hysteresis at various values of inductance at selected parallel capacitance (sensitivity) connected to the quartz crystal. The article shows that the proposed hysteresis measurement of the converter, which converts the inductance in the range between 95 and 100 μH to a frequency in the range between 1 and 200 kHz, has only 7 × 10−13 frequency instability (during the temperature change between 0 and 50 °C) with a maximum 1 × 10−11 hysteresis frequency difference. PMID:27367688

  16. The effect of crystal-plastic deformation on Ti concentration in quartz

    Science.gov (United States)

    Nachlas, W. O.; Hirth, G.; Whitney, D. L.; Teyssier, C. P.

    2013-12-01

    Quartz is a dominant phase controlling crustal rheology and strain localization, and the sensitivity of its recrystallization mechanisms to variations in temperature, pressure, and fluid activity make evaluation of these parameters crucial to reconstructing the deformation history of quartz-bearing rocks in the lithosphere. The advent of Ti in quartz thermobarometry provides a technique with potentially powerful applications for understanding the conditions at which rocks deform plastically in the crust. However, it is unclear how ductile deformation, specifically dislocation creep, affects Ti substitution in quartz and whether the Ti concentration in quartz accurately records the conditions at which quartz recrystallized. This study addresses these questions through a series of high P-T rock deformation experiments on precisely synthesized Ti-doped quartz aggregates to investigate the influence of strain and dynamic recrystallization on the concentration of Ti in quartz. Laboratory rock deformation experiments provide an ideal opportunity to study Ti solubility in deformed quartz because they allow for recrystallization to occur in a controlled environment; deformation experiments are conducted under isothermal and isobaric conditions at constant strain rate for increasing intervals of time to isolate the effect of strain on Ti chemistry of quartz. This study employs a novel doping synthesis method to produce a quartz aggregate consisting of a large population of quartz crystals doped with a precise Ti concentration where each individual crystal has a uniform dopant distribution. Deformation of a homogeneous starting material enables simulation of a retrograde solubility path, in which a sample with an initially high, uniform concentration is modified during deformation at conditions where the solubility is substantially lower. This enables observations to be made of the mechanisms responsible for mobilizing Ti through diffusion and exsolution to adjust to the

  17. Direct monitoring of paraquat induced cell death using quartz crystal sensor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong-Yun [School of Bioscience and Biotechnology, Tokyo University of Technology, 1404-1 Katakura, Hachioji, Tokyo 192-0982 (Japan); Department of Electrical Engineering and NTRC, Dong-A University, 840 Hadan 2-dong, Saha-gu, Busan 604-714 (Korea, Republic of); Kang, Hyen-Wook, E-mail: nanokang@bs.teu.ac.j [School of Bioscience and Biotechnology, Tokyo University of Technology, 1404-1 Katakura, Hachioji, Tokyo 192-0982 (Japan); Kaneko, Seiichi [School of Bioscience and Biotechnology, Tokyo University of Technology, 1404-1 Katakura, Hachioji, Tokyo 192-0982 (Japan); Kwon, Young-Soo, E-mail: yskwon@dau.ac.k [Department of Electrical Engineering and NTRC, Dong-A University, 840 Hadan 2-dong, Saha-gu, Busan 604-714 (Korea, Republic of); Muramatsu, Hiroshi, E-mail: muramatu@bs.teu.ac.j [School of Bioscience and Biotechnology, Tokyo University of Technology, 1404-1 Katakura, Hachioji, Tokyo 192-0982 (Japan)

    2009-11-30

    Paraquat, a nonselective herbicide and pesticide, has been implicated as an environmental toxicity which caused cell death. In order to investigate the influence of paraquat, we used a quartz crystal sensor with a micro CCD camera that measured morphology and resonance characteristics simultaneously. Human hepatoma cell line (HepG2) was cultured onto an indium tin oxide (ITO) surface of quartz crystal modified on a collagen film. After the growth of the cells, paraquat was injected to the chamber and the resonance responses of the quartz crystal were directly monitored with morphology. We analyzed changes of the cells by the resonance frequency (F) and the resonance resistance (R) responses (F-R diagram). With this analysis, we also observed the morphologies during cell culturing. From the data, we could know that paraquat caused the weakening and death of the cells. Namely, paraquat plays an important role in the free radicals production that led to apoptosis and cell death.

  18. Experimentally determining the relative efficiency of spherically bent germanium and quartz crystals

    Science.gov (United States)

    Brown, G. V.; Beiersdorfer, P.; Hell, N.; Magee, E.

    2016-11-01

    We have used the EBIT-I electron beam ion trap at the Lawrence Livermore National Laboratory and a duplicate Orion High Resolution X-ray Spectrometer (OHREX) to measure the relative efficiency of a spherically bent quartz (10 1 ¯ 1) crystal (2d = 6.687 Å) and a spherically bent germanium (111) crystal (2d = 6.532 Å). L-shell X-ray photons from highly charged molybdenum ions generated in EBIT-I were simultaneously focussed and Bragg reflected by each crystal, both housed in a single spectrometer, onto a single CCD X-ray detector. The flux from each crystal was then directly compared. Our results show that the germanium crystal has a reflection efficiency significantly better than the quartz crystal, however, the energy resolution is significantly worse. Moreover, we find that the spatial focussing properties of the germanium crystal are worse than those of the quartz crystal. Details of the experiment are presented, and we discuss the advantages of using either crystal on a streak-camera equipped OHREX spectrometer.

  19. A Study on a Partially Immersed Gold Electrode Using an Electrochemical Quartz Crystal Impedance System

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The electrochemical quartz crystal impedance system (EQCIS) has been used for the study of a partially immersed Au electrode in 0.2 mol/L NaClO4 aqueous solution.The influences of the immersed area and height of the electrode on the EQCIS responses were evaluated,showing the highest response sensitivity to liquid loading at the center of the piezoelectric quartz crystal electrode.The increase in the immersed height of the Au electrode at oxygen reduction potentials during potential cycling was measured by this technique.

  20. Robert Boyle's chiral crystal chemistry: computational re-evaluation of enantioselective adsorption on quartz.

    Science.gov (United States)

    Kahr, Bart; Chittenden, Brianne; Rohl, Andrew

    2006-02-01

    While searching for early examples of interactions of organic chromophores with minerals in the context of a systematic study of the process of dyeing crystals, we came across Robert Boyle's description of an experiment that may have been evidence of the enantioselective adsorption of a natural product, carminic acid (7-beta-D-glucopyranosyl-9,10-dihydro-3,5,6,8-tetrahydroxy-1-methyl-9,10-dioxo-2-anthracenecarboxylic acid), to the chiral surfaces of alpha-quartz, three centuries before such interactions became the subject of active chemical investigations. In order to determine whether Boyle did indeed observe enantioselective adsorption--albeit unbeknownst to him--we attempted to dye quartz with carminic acid according to his recipe. Quartz adsorbs carminic acid only because on heating it develops a network of microfissures that adsorb dye. This process depends on capillarity, not on specific non-covalent interactions; there is no evidence of enantioselectivity adsorption to heated crystals or enantioselective epitaxy to unheated crystals. These failures changed the focus of our inquiry: Why have almost all attempts to demonstrate the enantioselective adsorption of additives to quartz crystal surfaces been generally confounding and equivocal? In order to answer this question, we complement our experimental historical re-investigation with contemporary computational techniques for modeling crystal surface structure and the adsorption of additives. Minimizations of the energies associated with the adsorption of carminic acid to relaxed, hydrated d- and l-quartz {10(-)0} surfaces are analyzed in light of quartz's abysmal record as an enantioselective stationary phase.

  1. Double modulation of X radiation diffracted in a quartz single crystal by high and low frequency acoustic waves

    CERN Document Server

    Kocharyan, L A; Bornazyan, H S

    1986-01-01

    The time dependence of X radiation diffracted in a quartz single crystal is experimentally investigated when surface acoustic waves modulated by low frequency oscillations of different frequencies and forms are excited in the crystal.

  2. The new piezoelectric single crystal obtained by the Ge doping in the α-quartz structure

    Science.gov (United States)

    Miclau, M.; Grozescu, A.; Bucur, R.; Poienar, M.; Vlazan, P.; Grozescu, I.; Miclau, N.; Muscutariu, I.

    2009-03-01

    The most interesting properties of the quartz-like crystals are its piezoelectric properties, which are strongly influenced by the intrinsic structural distortions of the material and the crystal growth conditions. Thus, physical properties such as coupling coefficient, the αβ transition can be directly related to structural distortions in terms of the bridging angle. We propose a new way to increase the structural distortion, using Ge to dope the SiO2 structure with respect to α-quartz structure type. Growth of α -SixGe1-xO2 crystal was realized hydrothermally using a temperature gradient method. Single crystals were investigated by electron microprobe analysis, X-ray diffraction and atomic force microscopy. The results open the possibility to tune the piezoelectric properties of these materials by varying the chemical composition.

  3. Evaluation of sagittal focusing for a spherical quartz crystal x-ray analyzer with synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Nino R.; Macrander, Albert T.; Hill, Kenneth W.; Baronova, Elena O.; George, Kevin M.; Kotick, Jordan T.

    2015-10-01

    To attain optimum performance in applications such as x-ray imaging and spectroscopy, a spherically bent crystal must diffract well across its entire surface. X-ray topography of sample crystals shows isolated regions where diffraction is problematic, even for a crystal where inspection with visible light does not suggest problems. Covering problem spots may improve the crystal’s focus and decrease the background. We explore the special properties of synchrotron radiation to examine typical spherical crystals from alpha-quartz, in a perpendicular geometry that is especially convenient to examine sagittal focusing.

  4. Determination of Mass Sensitivity of Crystal Quartz Resonators at Students' Laboratory

    Science.gov (United States)

    Greczylo, Tomasz; Mazur, Piotr; Debowska, Ewa; Wieczorek, Piotr

    2010-01-01

    This paper presents an experiment in which students determine the mass sensitivity of three crystal quartz resonators, designed to be carried out in "Physics Laboratory II" at the Institute of Experimental Physics, University of Wroclaw. The authors discuss the process of setting up the experiment and the results of the measurements. They clearly…

  5. Determination of Mass Sensitivity of Crystal Quartz Resonators at Students' Laboratory

    Science.gov (United States)

    Greczylo, Tomasz; Mazur, Piotr; Debowska, Ewa; Wieczorek, Piotr

    2010-01-01

    This paper presents an experiment in which students determine the mass sensitivity of three crystal quartz resonators, designed to be carried out in "Physics Laboratory II" at the Institute of Experimental Physics, University of Wroclaw. The authors discuss the process of setting up the experiment and the results of the measurements.…

  6. Dielectric relaxation processes in smoky quartz crystals at very low temperatures

    NARCIS (Netherlands)

    Vos, W.J. de; Volger, J.

    1967-01-01

    The relaxation time governing the dielectric loss of smoky quartz crystals appears to level off as a function of temperature below 12°K, approaching a value of about 1 msec. The relaxational behaviour of the colour centres is discussed in terms of tunneling processes.

  7. Dielectric relaxation processes in smoky quartz crystals at very low temperatures

    NARCIS (Netherlands)

    Vos, W.J. de; Volger, J.

    1967-01-01

    The relaxation time governing the dielectric loss of smoky quartz crystals appears to level off as a function of temperature below 12°K, approaching a value of about 1 msec. The relaxational behaviour of the colour centres is discussed in terms of tunneling processes.

  8. A new investigation of dielectric relaxation processes in smoky quartz crystals

    NARCIS (Netherlands)

    Vos, W.J. de; Volger, J.

    1967-01-01

    Dielectric loss measurements on smoky quartz crystals over a wide frequency and temperature range (200 Hz-2.5 MHz and 20.4–160°K) showed, besides the well-known relaxation process at low temperatures, also a new relaxation mechanism, which becomes dominant above 100°K. There are strong arguments tha

  9. NMR spectroscopy of experimentally shocked single crystal quartz: A reexamination of the NMR shock barometer

    Science.gov (United States)

    Fiske, P. S.; Gratz, A. J.; Nellis, W. J.

    1993-01-01

    Cygan and others report a broadening of the Si-29 nuclear magnetic resonance (NMR) peak for synthetic quartz powders with increasing shock pressure which they propose as a shock wave barometer for natural systems. These results are expanded by studying single crystal quartz shocked to 12 and 33 GPa using the 6.5 m two-stage light-gas gun at Lawrence Livermore National Laboratories. Our NMR results differ substantially from those of Cygan and others and suggest that the proposed shock wave barometer may require refinement. The difference in results between this study and that of Cygan and others is most likely caused by different starting materials (single crystal vs. powder) and different shock loading histories. NMR results from single crystal studies may be more applicable to natural systems.

  10. NMR spectroscopy of experimentally shocked single crystal quartz: A reexamination of the NMR shock barometer

    Science.gov (United States)

    Fiske, P. S.; Gratz, A. J.; Nellis, W. J.

    1993-01-01

    Cygan and others report a broadening of the Si-29 nuclear magnetic resonance (NMR) peak for synthetic quartz powders with increasing shock pressure which they propose as a shock wave barometer for natural systems. These results are expanded by studying single crystal quartz shocked to 12 and 33 GPa using the 6.5 m two-stage light-gas gun at Lawrence Livermore National Laboratories. Our NMR results differ substantially from those of Cygan and others and suggest that the proposed shock wave barometer may require refinement. The difference in results between this study and that of Cygan and others is most likely caused by different starting materials (single crystal vs. powder) and different shock loading histories. NMR results from single crystal studies may be more applicable to natural systems.

  11. Quartz dissolution. I - Negative crystal experiments and a rate law. II - Theory of rough and smooth surfaces

    Science.gov (United States)

    Gratz, Andrew J.; Bird, Peter

    1993-01-01

    The range of the measured quartz dissolution rates, as a function of temperature and pOH, extent of saturation, and ionic strength, is extended to cover a wider range of solution chemistries, using the negative crystal methodology of Gratz et al. (1990) to measure the dissolution rate. A simple rate law describing the quartz dissolution kinetics above the point of zero charge of quartz is derived for ionic strengths above 0.003 m. Measurements were performed on some defective crystals, and the mathematics of step motion was developed for quartz dissolution and was compared with rough-face behavior using two different models.

  12. Electrical Conductivity of Synthetic Quartz Crystals at High Temperature and Pressure from Complex Impedance Measurements

    Institute of Scientific and Technical Information of China (English)

    王多君; 李和平; 刘丛强; 易丽; 丁东业; 苏根利; 张卫刚

    2002-01-01

    An electrical conductivity measurement system under high-pressure conditions with a multi-anvil high-pressure apparatus by an ac complex impedance method was set up. With this system, we have successfully measured the electrical conductivity of synthetic quartz under pressure up to approximately 1.0 GPa in the temperature range 661-987K. The values of electrical conductivity decrease with the increasing pressure and increase with the increasing temperature. The activation enthalpies for the α-quartz crystals are 1.10-1.28eV. The electrical conductivity of α-quartz is ionic, with Na ions moving in channels parallel to the c-axis being the predominant current carrier.

  13. KTN thin films prepared by pulsed laser deposition on transparent single crystal quartz (100)

    Institute of Scientific and Technical Information of China (English)

    WANG; Xiaodong; PENG; Xiaofeng; ZHANG; Duanming

    2005-01-01

    Using the Sol-Gel method to produce the KTN ultrafine powder and the sintering technique with K2O atmosphere to prepare KTN ceramics as the targets instead of the KTN single crystal, highly oriented KTN thin films were produced on the transparent single crystal quartz (100) by the pulsed laser deposition (PLD). Since the thermal stress sustained by the quartz is relatively small, the limit temperature of the quartz substrates(300℃) is much lower than that of the P-Si substrates (560℃); the prepared thin film is at amorphous state. Increasing the pulsed laser energy density in the process incorporated with annealing the film after deposition at different temperatures converts the amorphous films into crystal. The optimal pulsed laser energy density and annealing temperature were 2.0 J/cm2 and 600℃, respectively. A discussion was made to understand the mechanism of film production at relatively low substrate temperature by PLD and effects of the annealing temperatures on the forming of the perovskite phase, and optimal conditions for the orientation of the crystal grain.

  14. Density-viscosity product of small-volume ionic liquid samples using quartz crystal impedance analysis.

    Science.gov (United States)

    McHale, Glen; Hardacre, Chris; Ge, Rile; Doy, Nicola; Allen, Ray W K; MacInnes, Jordan M; Bown, Mark R; Newton, Michael I

    2008-08-01

    Quartz crystal impedance analysis has been developed as a technique to assess whether room-temperature ionic liquids are Newtonian fluids and as a small-volume method for determining the values of their viscosity-density product, rho eta. Changes in the impedance spectrum of a 5-MHz fundamental frequency quartz crystal induced by a water-miscible room-temperature ionic liquid, 1-butyl-3-methylimiclazolium trifluoromethylsulfonate ([C4mim][OTf]), were measured. From coupled frequency shift and bandwidth changes as the concentration was varied from 0 to 100% ionic liquid, it was determined that this liquid provided a Newtonian response. A second water-immiscible ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide [C4mim][NTf2], with concentration varied using methanol, was tested and also found to provide a Newtonian response. In both cases, the values of the square root of the viscosity-density product deduced from the small-volume quartz crystal technique were consistent with those measured using a viscometer and density meter. The third harmonic of the crystal was found to provide the closest agreement between the two measurement methods; the pure ionic liquids had the largest difference of approximately 10%. In addition, 18 pure ionic liquids were tested, and for 11 of these, good-quality frequency shift and bandwidth data were obtained; these 12 all had a Newtonian response. The frequency shift of the third harmonic was found to vary linearly with square root of viscosity-density product of the pure ionic liquids up to a value of square root(rho eta) approximately 18 kg m(-2) s(-1/2), but with a slope 10% smaller than that predicted by the Kanazawa and Gordon equation. It is envisaged that the quartz crystal technique could be used in a high-throughput microfluidic system for characterizing ionic liquids.

  15. Adsorption of Pluronic F-127 on Surfaces with Different Hydrophobicities Probed by Quartz Crystal Microbalance with Dissipation

    NARCIS (Netherlands)

    Nejadnik, M.R.; Olsson, A.L.J.; Sharma, P.K.; Mei, van der H.C.; Norde, W.; Busscher, H.J.

    2009-01-01

    Triblock copolymers of polyethylene oxide (PEO) and polypropylene oxide (PPO), that is, PEOn-PPOm-PEOn, better known as Pluronic can adsorb to surfaces in either a pancake or a brushlike configuration. The brushlike configuration is advantageous in numerous applications, since it constitutes a

  16. Charge Transport Processes of Immobilized Heteropolyanions at Self-assembled Monolayer Modified Gold Electrode by Electrochemical Quartz Crystal Microbalance Measurement

    Institute of Scientific and Technical Information of China (English)

    BU Xin-yuan; JIAO Lian-sheng; HAN Dong-xue; YANG Gui-fu

    2009-01-01

    ions in a 1 mol/L H2SO4 solution and played a key role in the abnormal change of the resonant fequency. Such a change was attributed to different packing densities derived by means of differently immobilized methods.

  17. Adsorption of Saliva Related Protein on Denture Materials: An X-Ray Photoelectron Spectroscopy and Quartz Crystal Microbalance Study

    Directory of Open Access Journals (Sweden)

    Akiko Miyake

    2016-01-01

    Full Text Available The aim of this study was to evaluate the difference in the adsorption behavior of different types of bovine salivary proteins on the PMMA and Ti QCM sensors are fabricated by spin-coating and sputtering onto bare QCM sensors by using QCM and X-ray photoelectron spectroscopy (XPS. SPM, XPS, and contact angle investigations were carried out to determine the chemical composition and surface wettability of the QCM surface. We discuss the quality of each sensor and evaluate the potential of the high-frequency QCM sensors by investigating the binding between the QCM sensor and the proteins albumin and mucin (a salivary-related protein. The SPM image showed a relatively homogeneous surface with nano-order roughness. The XPS survey spectra of the thin films coated on the sensors were similar to the binding energy of the characteristic spectra of PMMA and Ti. Additionally, the amount of salivary-related protein on the PMMA QCM sensor was higher than those on the Ti and Au QCM sensors. The difference of protein adsorption is proposed to be related to the wettability of each material. The PMMA and Ti QCM sensors are useful tools to study the adsorption and desorption of albumin and mucin on denture surfaces.

  18. Low Temperature Quartz Crystal Oscillator Fast Warm-Up Saw Oscillator.

    Science.gov (United States)

    1981-07-01

    and given at I Hz from the carrier. From these experimental data the dependance between 1/F noise and Q-fact : is determined by using a regression...for the thermal phonons. The anharmonicities are introduced by means of a strain dependance of the phono frequencies. A detailed description of the...study shown for the first time a correlation between 1/F noise and Q-factor in quartz crystal resonators. This dependance was confirmed on the one

  19. Fluorinated Epoxy Resins-based Sorbent Coating Materials for Quartz Piezoelectric Crystal Detector

    Directory of Open Access Journals (Sweden)

    D. C Gupta

    2004-04-01

    Full Text Available Fluorinated epoxy resins were synthesised and evaluated as sorbent coating materials for the detection of organophosphorus compounds using quartz piezoelectric crystal detector. These resins were prepared by reacting excess of epichlorohydrin with each of or in combination of fluorinated diols, ie, a, a, a', a' tetrakis (trifluoromethyl 1,3 benzene dimethanol (TTFMBD, 4,4'bis-2-hydroxy hexafluoro isopropyl biphenyl (BHHFIBP, 4,4'dihydroxyocta fluorodiphenyl (DHOFDP and 2,2,3,3,4,4 hexafluoro 1,5 pentanediol (HFPD in the presence of sodium hydroxide at reflux temperature. These polymers were extracted in organic solvents and dried. Each of these fluoroepoxy resins were coated over quartz piezoelectric crystal by solution-casting method and tested using dimethylmethyl phosphonate (DMMP as model compound. Change in the  frequency (AF of quartz piezoelectric crystal oscillator was recorded. Sensitive and potential fluorinated epoxy resins, ie, diglycidylethers (DGE of HFPD-TTFMBD (in the molar ratio 6:4 and DGE (HFPD-BHHFIBP in the molar ratio 4:6 were characterised by viscosity, number average molecular weight (Mn, epoxy equivalent, infrared spectroscopy, and thermal stability.

  20. Neutron diffraction in a quartz single crystal under the action of acoustic oscillations or a temperature gradient

    CERN Document Server

    Mkrtchyan, A R; Hunanyan, H A; Beglaryan, A G

    1986-01-01

    The paper deals with the problem of neutron diffraction in a quartz single crystal under the action of acoustic oscillations or a temperature gradient in the Laue geometry. Theoretical conclusions were compared with experimental results.

  1. Tunable hard X-ray spectrometer utilizing asymmetric planes of a quartz transmission crystal.

    Science.gov (United States)

    Seely, John F; Henins, Albert; Feldman, Uri

    2016-05-01

    A Cauchois type hard x-ray spectrometer was developed that utilizes the (301) diffraction planes at an asymmetric angle of 23.51° to the normal to the surface of a cylindrically curved quartz transmission crystal. The energy coverage is tunable by rotating the crystal and the detector arm, and spectra were recorded in the 8 keV to 20 keV range with greater than 2000 resolving power. The high resolution results from low aberrations enabled by the nearly perpendicular angle of the diffracted rays with the back surface of the crystal. By using other asymmetric planes of the same crystal and rotating to selected angles, the spectrometer can operate with high resolution up to 50 keV.

  2. Differing effects of water fugacity deformation of quartzites and milky quartz single crystals

    Science.gov (United States)

    Holyoke, C. W.; Kronenberg, A. K.

    2010-12-01

    Previous studies of quartzite deformation by dislocation creep have documented a strong dependence of mechanical properties on pressure, which has been interpreted as a relationship between strain rate and water fugacity (Kronenberg and Tullis, 1984; Kohlstedt et al., 1995; Chernak et al. 2009). However, natural milky quartz single crystals deformed by basal slip can be water-weakened over a wide range of pressure (and water fugacities), with strengths that appear to depend on total water content at a fixed water fugacity. The difference of behavior between these two is perplexing since infrared spectra collected from quartzites and milky quartz single crystals indicate that they have the same forms of intragranular water and microstructures indicate the same slip system is activated. The only difference between these materials is that quartzites include populations of grains of all orientations, separated by grain boundaries. In order to resolve this discrepancy we have performed deformation experiments on a natural quartzite (Black Hills quartzite) and natural milky quartz single crystals oriented for easy slip on the basal slip system at identical conditions (800°C, strain rate = 10-6/s) with no added water. During each experiment cores of each material, which have a fixed water content, were subjected to pressure stepping; an initial deformation step was performed at 1.5 GPa, then the sample was unloaded and one or more deformation steps were performed at lower pressures (as low as 0.6 GPa) prior to returning to 1.5 GPa for a final deformation step. The strength of quartzite increases dramatically at lower pressure and lower water fugacity, but strength decreases again returning to high pressure during the final deformation step. The strength of milky quartz single crystals increases as well, but by far less than observed for quartzites. The water fugacity exponents (m) of the quartzite and single crystals are 1.9 and 0.8, respectively, (assuming power law

  3. A Simple Method for the Detection of Long-Chain Fatty Acids in an Anaerobic Digestate Using a Quartz Crystal Sensor

    Directory of Open Access Journals (Sweden)

    Takuro Kobayashi

    2016-12-01

    Full Text Available In anaerobic digestion (AD, long-chain fatty acids (LCFAs produced by hydrolysis of lipids, exhibit toxicity against microorganisms when their concentration exceeds several millimolar. An absorption detection system using a quartz crystal microbalance (QCM was developed to monitor the LCFA concentration during an anaerobic digester’s operation treating oily organic waste. The dissociation of the LCFAs considerably improved the sensor response and, moreover, enabled it to specifically detect LCFA from the mixture of LCFA and triglyceride. Under alkaline conditions, the frequency-shift rates of the QCM sensor linearly increased in accordance with palmitic acid concentration in the range of 0–100 mg/L. Frequency changes caused by anaerobic digestate samples were successfully measured after removing suspended solids and adjusting the pH to 10.7. Finally, the QCM measurements for digestate samples demonstrated that frequency-shift rates are highly correlated with LCFA concentrations, which confirmed that the newly developed QCM sensor is helpful for LCFA monitoring in terms of rapidness and usability.

  4. Simultaneous Impedance Analysis of Three Parallel Piezoelectric Quartz Crystals for Electrochemical Depletion Layer Effect Study

    Institute of Scientific and Technical Information of China (English)

    Hui Yan liu; Qing Ji XIE

    2004-01-01

    Simultaneous impedance analysis of three one-face sealed resonating piezoelectric quartz crystals (PQCs) in parallel is proposed through admittance measurements of the three PQCs on one impedance analyzer and then non-linear fitting according to the parallel combination of three Butterworth-Van Dyke circuits. Responses of each PQC obtained from the three-PQC mode agreed well with those measured separately in series sucrose aqueous solutions. This novel method has been used for the study of depletion-layer effect during ferri-/ferrocyanide electrochemical reactions.

  5. Photonic crystal enhanced fluorescence using a quartz substrate to reduce limits of detection.

    Science.gov (United States)

    Pokhriyal, Anusha; Lu, Meng; Chaudhery, Vikram; Huang, Cheng-Sheng; Schulz, Stephen; Cunningham, Brian T

    2010-11-22

    A Photonic Crystal (PC) surface fabricated upon a quartz substrate using nanoimprint lithography has been demonstrated to enhance light emission from fluorescent molecules in close proximity to the PC surface. Quartz was selected for its low autofluorescence characteristics compared to polymer-based PCs, improving the detection sensitivity and signal-to-noise ratio (SNR) of PC Enhanced Fluorescence (PCEF). Nanoimprint lithography enables economical fabrication of the subwavelength PCEF surface structure over entire 1x3 in2 quartz slides. The demonstrated PCEF surface supports a transverse magnetic (TM) resonant mode at a wavelength of λ = 632.8 nm and an incident angle of θ = 11°, which amplifies the electric field magnitude experienced by surface-bound fluorophores. Meanwhile, another TM mode at a wavelength of λ = 690 nm and incident angle of θ = 0° efficiently directs the fluorescent emission toward the detection optics. An enhancement factor as high as 7500 × was achieved for the detection of LD-700 dye spin-coated upon the PC, compared to detecting the same material on an unpatterned glass surface. The detection of spotted Alexa-647 labeled polypeptide on the PC exhibits a 330 × SNR improvement. Using dose-response characterization of deposited fluorophore-tagged protein spots, the PCEF surface demonstrated a 140 × lower limit of detection compared to a conventional glass substrate.

  6. The influence of vibrations on time reference signals generated using quartz crystals

    Science.gov (United States)

    Drumea, Andrei; Marcu, Alina; Plotog, Ioan

    2016-12-01

    32.768 kHz low frequency crystals are found in a large part of today's embedded systems that use microcontrollers especially in battery supplied applications which need low power consumption1]. Their main role is to offer a stable time reference. There are situations in which time measurement is needed when the system works in a mechanically unstable environment (cars, industrial equipment). The paper presents the studies done on the behavior of 32.768 kHz quartz crystals that are part of embedded systems which operate in a vibrating environment, in terms of period and long-time jitter of the generated time reference signal. The investigations of this effect were done using a test bench especially designed for this purpose which can measure the presented parameters determined by controlled mechanical stimulus (waveform, amplitude and frequency of the vibrations).

  7. Finishing of AT-cut quartz crystal wafer with nanometric thickness uniformity by pulse-modulated atmospheric pressure plasma etching.

    Science.gov (United States)

    Yamamura, Kazuya; Ueda, Masaki; Shibahara, Masafumi; Zettsu, Nobuyuki

    2011-04-01

    Quartz resonator is a very important device to generate a clock frequency for information and telecommunication system. Improvement of the productivity of the quartz resonator is always required because a huge amount of the resonator is demanded for installing to various electronic devices. Resonance frequency of the quartz resonator is decided by the thickness of the quartz crystal wafer. Therefore, it is necessary to uniform the thickness distribution of the wafer with nanometric level. We have proposed the improvement technique of the thickness distribution of the quartz crystal wafer by numerically controlled correction using atmospheric pressure plasma which is non-contact and chemical removal technique. Heating effects of the quartz wafer in the removal rate and the correction accuracy were investigated. The heating of the substrate and compensate of the scanning speed of the worktable according to the variation of the surface temperature enabled an increase of 50% in the etching rate and 10-nanometric-level accuracy in the correction of the thickness distribution of the quartz wafer, respectively.

  8. PARALLEL FINITE ELEMENT ANALYSIS OF HIGH FREQUENCY VIBRATIONS OF QUARTZ CRYSTAL RESONATORS ON LINUX CLUSTER

    Institute of Scientific and Technical Information of China (English)

    Ji Wang; Yu Wang; Wenke Hu; Wenhua Zhao; Jianke Du; Dejin Huang

    2008-01-01

    Quartz crystal resonators are typical piezoelectric acoustic wave devices for frequency control applications with mechanical vibration frequency at the radio-frequency (RF) range. Precise analyses of the vibration and deformation are generally required in the resonator design and improvement process. The considerations include the presence of electrodes, mountings, bias fields such as temperature, initial stresses, and acceleration. Naturally, the finite element method is the only effective tool for such a coupled problem with multi-physics nature. The main challenge is the extremely large size of resulted linear equations. For this reason, we have been employing the Mindlin plate equations to reduce the computational difficulty. In addition, we have to utilize the parallel computing techniques on Linux clusters, which are widely available for academic and industrial applications nowadays, to improve the computing efficiency. The general principle of our research is to use open source software components and public domain technology to reduce cost for developers and users on a Linux cluster. We start with a mesh generator specifically for quartz crystal resonators of rectangular and circular types, and the Mindlin plate equations are implemented for the finite element analysis. Computing techniques like parallel processing, sparse matrix handling, and the latest eigenvalue extraction package are integrated into the program. It is clear from our computation that the combination of these algorithms and methods on a cluster can meet the memory requirement and reduce computing time significantly.

  9. Radiation stimulated effects in crystals of quartz and berlinit with different type and degree of perfection structure

    CERN Document Server

    Ibragimov, Z D

    2001-01-01

    of structure. The effectiveness of creation of additional defects near defects of one type is increased with growth of concentration of other types of structure violations. It was established that in crystals of quartz and berlinit alpha-beta-transition during neutron irradiation occurs through formation of seeds of beta-phase. It was shown that the grown layer with beta-phase inherited also neutron induced defects of alpha-phase as well as defects related to beta-phase of quartz. The structure of amorphous phase formed around seeds of beta-phase differs from quartz glass structure. The formation of regions with structure closed to quartz glass structure occurs after definite neutron fluence values. In quartz crystals there are several defect centers emitting in red spectral range. The processes of impact and non-impact production of point defects, mechanisms of structure transformations in quartz and berlinit crystals irradiated by various types of radiation with over- and sub- threshold energy were studied....

  10. Microstructures and Crystallographic Misorientation in Experimentally Deformed Natural Quartz Single Crystals

    Science.gov (United States)

    Thust, Anja; Heilbronner, Renée.; Stünitz, Holger

    2010-05-01

    Samples of natural milky quartz were deformed in a Griggs deformation apparatus at different confining pressures (700 MPa, 1000 MPa, 1500 MPa), with constant displacement rates of 1 * 10-6s-1, axial strains of 3 - 19%, and at a temperature of 900° C. The single crystal starting material contains a large number of H2O-rich fluid inclusions. Directly adjacent to the fluid inclusions the crystal is essentially dry (50-150H/106Si, determined by FTIR). The samples were cored from a narrow zone of constant 'milkyness' (i.e. same density of fluid inclusions) in a large single crystal in two different orientations (1) normal to one of the prism planes (⊥{m} orientation) and (2) 45° to and to (O+ orientation).During attaining of the experimental P and T conditions, numerous fluid inclusions decrepitate by cracking. Rapid crack healing produces regions of very small fluid inclusions ('wet' quartz domains). Only these regions are subsequently deformed by dislocation glide, dry quartz domains without cracking and decrepitation of fluid inclusions remain undeformed. Sample strain is not sufficient to cause recrystallization, so that deformation is restricted to dislocation glide. In experiments at lower temperatures (800, 700° C) or at lower strain rate (10-5s-1) there is abundant cracking and semi-brittle deformation, indicating that 900° C, (10-6s-1) represents the lower temperature end of crystal plastic deformation in these single crystals. Peak strengths (at 900° C) range between 150 and 250 MPa for most samples of both orientations. There is a trend of decreasing strength with increasing confining pressure, as described by Kronenberg and Tullis (1984) for quartzites, but the large variation in strength due to inhomogeneous sample strain precludes a definite analysis of the strength/pressure dependence in our single crystals. In the deformed samples, we can distinguish a number of microstructures and inferred different slip systems. In both orientations, deformation

  11. The effect of the carbon dissolution on the crystal structure of a-quartz

    Science.gov (United States)

    Mitani, S.; Kyono, A.

    2015-12-01

    Silicon is one of the major and important element that constitutes the Earth's crust and mantle. An enormous amount of carbon is also contained in the Earth's interior, which suggests that silicate could be closely interacted with carbon under high-pressure and high-temperature (Sen et al. 2013, PNAS). It is suggested that carbon dioxide is dissolved in cristobalite and the average composition of CO2-SiO2 solid solution is C0.6(1)Si0.4(1)O2 High-pressure experiment (Santoro et al. 2014, Nat. Commun.). Furthermore, the first-principles calculations suggested the possibility of successive CO2 dissolution in cristobalite at ambient pressure (Aravindh et al. 2007, Solid State Commun.). However, CO2-SiO2 solid solution at ambient pressure has not confirmed in laboratory experiment. In this study, we mixed amorphous silica and amorphous carbon and synthesized CO2-SiO2 solid solution at high-temperature under ambient pressure. Powder amorphous silica and graphite was mixed together in the agate mill in order to be homogenized mixture. They were heated for 1300 ˚C, 3 days under ambient pressure. Then, the samples were quenched at room temperature. The samples of CO2-SiO2 solid solution were carefully examined by powder XRD, EPMA measurement, and so on. From the result of the powder XRD, the products were a-quartz. In this lecture, we report the quantity of carbon dissolved in a-quartz and its effect for the crystal structure of a-quartz in detail.

  12. Biomimetic piezoelectric quartz crystal sensor with chloramphenicol-imprinted polymer sensing layer.

    Science.gov (United States)

    Ebarvia, Benilda S; Ubando, Isaiah E; Sevilla, Fortunato B

    2015-11-01

    The measurement of banned antibiotic like chloramphenicol is significant for customer protection and safety. The presence of residual antibiotics in foods and food products of animal origin could pose as health hazards and affect food quality for global acceptance. In this study, the potential of a chloramphenicol sensor based on molecularly imprinted polymer (MIP) coupled with a piezoelectric quartz crystal was explored. The MIP was prepared by precipitation polymerization at 60 °C. Methacrylic acid was used as monomer, trimethylolpropane trimethacrylate (TRIM) as crosslinker, and chloramphenicol as the template. Template removal on the resulting polymer was done by extraction using methanol-acetic acid. Characterization of the MIP and NIP were conducted by spectroscopic and microscopic methods. These further supported the imprinting and rebinding process of chloramphenicol to the polymer matrix. The chloramphenicol sensor was devised by spin-coating onto one side of the 10 MHz AT-cut quartz crystal the MIP suspension in polyvinylchloride-tetrahydrofuran (6:2:1 w/w/v) solution. Optimization of sensor response was performed by varying the type of cross-linker, amount of MIP sensing layer, curing time, and pH. The sensor exhibited good sensitivity of about 73 Hz/log (conc., µg mL(-1)) and good repeatability (rsd<10%). A linear relationship (r(2)=0.9901) between frequency shift and chloramphenicol concentration in the range of 1×10(-6) up to 1×10(-1) µg/mL was obtained. The sensor response was highly selective to chloramphenicol than with other compounds of similar chemical structures. Acceptable percent recovery was obtained for real sample analysis using the sensor. The proposed sensor could be a promising low cost and highly sensitive approach for residual chloramphenicol quantification in food products.

  13. Enantioselective piezoelectric quartz crystal sensor for d-methamphetamine based on a molecularly imprinted polymer.

    Science.gov (United States)

    Arenas, Leveriza F; Ebarvia, Benilda S; Sevilla, Fortunato B

    2010-08-01

    A piezoelectric quartz crystal (PQC) sensor based on a molecularly imprinted polymer (MIP) has been developed for enantioselective and quantitative analysis of d-(+)-methamphetamine (d(+)-MA). The sensor was produced by bulk polymerization and the resulting MIP was then coated on the gold electrode of an AT-cut quartz crystal. Conditions such as volume of polymer coating, curing time, type of PQC, baseline solvent, pH, and buffer type were found to affect the sensor response and were therefore optimized. The PQC-MIP gave a stable response to different concentrations of d(+)-MA standard solutions (response time = 10 to 100 s) with good repeatability (RSD = 0.03 to 3.09%; n = 3), good reproducibility (RSD = 3.55%; n = 5), and good reversibility (RSD = 0.36%; n = 3). The linear range of the sensor covered five orders of magnitude of analyte concentration, ranging from 10(-5) to 10(-1) microg mL(-1), and the limit of detection was calculated as 11.9 pg d(+)-MA mL(-1) . The sensor had a highly enantioselective response to d(+)-MA compared with its response to l(-)-MA, racemic MA, and phentermine. The developed sensor was validated by applying it to human urine samples from drug-free individuals spiked with standard d(+)-MA and from a confirmed MA user. Use of the standard addition method (SAM) and samples spiked with d(+)-MA at levels ranging from 1 x 10(-3) to 1 x 10(-2) microg mL(-1) showed recovery was good (95.3 to 110.9%).

  14. An approach for phosphate removal with quartz sand, ceramsite, blast furnace slag and steel slag as seed crystal.

    Science.gov (United States)

    Qiu, Liping; Wang, Guangwei; Zhang, Shoubin; Yang, Zhongxi; Li, Yanbo

    2012-01-01

    The phosphate removal abilities and crystallization performance of quartz sand, ceramsite, blast furnace slag and steel slag were investigated. The residual phosphate concentrations in the reaction solutions were not changed by addition of the ceramsite, quartz sand and blast furnace slag. The steel slag could provide alkalinity and Ca(2+) to the reaction solution due to its hydration activity, and performed a better phosphate removal performance than the other three. Under the conditions of Ca/P 2.0, pH 8.5 and 10 mg P/L, the phosphate crystallization occurred during 12 h. The quartz sand and ceramsite did not improve the phosphate crystallization, but steel slag was an effective seed crystal. The phosphate concentration decreased drastically after 12 h after addition of steel slag, and near complete removal was achieved after 48 h. The XRD analysis showed that the main crystallization products were hydroxyapatite (HAP) and the crystallinity increased with the reaction time. Phosphate was successfully recovered from low phosphate concentration wastewater using steel slag as seed material.

  15. Monitoring the Growth Rate of HAp Crystal on the Surface of Ti/TiO_2 in SCS by a Quartz Crystal Microbalance

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    1 IntroductionCommercially pure titanium and some titanium alloys including Ti6Al4V have been widely used in the manufacture of dental and orthopaedic implants. Although bulk properties dictate the mechanical properties of biomaterials, tissue-biomaterial processes are surface phenomena and they are governed by surface properties. Moreover, bioactivity of titanium surfaces is not high enough to induce the direct growth of the bone tissue and good bone fixation takes several months. The application of hydrox...

  16. Preparation and characterization of ethylenediamine and cysteamine plasma polymerized films on piezoelectric quartz crystal surfaces for a biosensor

    Energy Technology Data Exchange (ETDEWEB)

    Mutlu, Selma [Department of Chemical Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey)], E-mail: smselma@hacettepe.edu.tr; Coekeliler, Dilek [Plasma Aided Bioengineering and Biotechnology Research Group(PABB), Faculty of Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey); Shard, Alex [Department of Engineering Materials, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield, S1 3JD (United Kingdom); Goktas, Hilal [Physics Department, Canakkale Onsekiz Mart University, 17100 Canakkale (Turkey); Ozansoy, Berna [Department of Chemical Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey); Mutlu, Mehmet [Plasma Aided Bioengineering and Biotechnology Research Group(PABB), Faculty of Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey)

    2008-01-30

    This paper describes a method for the modification of quartz crystal surfaces to be used as a transducer in biosensors that allow recognition and quantification of certain biomolecules (antibodies, enzymes, proteins, etc). Quartz crystal sensors were modified by a plasma based electron beam generator in order to detect the level of the toxin histamine within biological liquids (blood, serum) and food (wine, cheese, fish etc.). Cysteamine and ethylenediamine were used as precursors in the plasma. After each modification step, the layers on the quartz crystal were characterized by frequency measurements. Modified surfaces were also characterized by contact angle, X-ray photoelectron spectroscopy and atomic force microscopy to determine the physical and chemical characteristics of the surfaces after each modification. Finally, the performance of the sensors were tested by the response to histamine via frequency shifts. The frequency shifts of the sensors prepared by plasma polymerization of ethylenediamine and cysteamine were approximately 3230 Hz and 5630 Hz, respectively, whereas the frequency change of the unmodified crystal surface was around 575 Hz.

  17. Multiplexed cancer biomarker detection using quartz-based photonic crystal surfaces.

    Science.gov (United States)

    Huang, Cheng-Sheng; Chaudhery, Vikram; Pokhriyal, Anusha; George, Sherine; Polans, James; Lu, Meng; Tan, Ruimin; Zangar, Richard C; Cunningham, Brian T

    2012-01-17

    A photonic crystal (PC) surface is demonstrated as a high-sensitivity platform for detection of a panel of 21 cancer biomarker antigens using a sandwich enzyme-linked immunosorbent assay (ELISA) microarray format. A quartz-based PC structure fabricated by nanoimprint lithography, selected for its low autofluorescence, supports two independent optical resonances that simultaneously enable enhancement of fluorescence detection of biomarkers and label-free quantification of the density of antibody capture spots. A detection instrument is demonstrated that supports fluorescence and label-free imaging modalities, with the ability to optimize the fluorescence enhancement factor on a pixel-by-pixel basis throughout the microarray using an angle-scanning approach for the excitation laser that automatically compensates for variability in surface chemistry density and capture spot density. Measurements show that the angle-scanning illumination approach reduces the coefficient of variation of replicate assays by 20-99% compared to ordinary fluorescence microscopy, thus supporting reduction in limits of detectable biomarker concentration. Using the PC resonance, biomarkers in mixed samples were detectable at the lowest concentrations tested (2.1-41 pg/mL), resulting in a three-log range of quantitative detection.

  18. Effect of fluid motion on the impact erosion by a micro-particle on quartz crystals

    Science.gov (United States)

    Cai, D. H.; Qi, H.; Wen, D. H.; Zhang, L.; Yuan, Q. L.; Chen, Z. Z.

    2016-08-01

    Abrasive slurry jet (ASJ) is a promising technology to process a variety of materials with advantages of high flexibility, no heat affected zone and high cutting efficiency. In this paper, the impressions generated on a quartz crystal specimen by the impacts of micro-particles laden in a water flow and the associated impact erosion mechanisms are presented and discussed in order to effectively and efficiently control the machining quality. Both brittle and ductile mode erosions coexist in the machining process due to the influence of the fluid motion on the trajectories of particles near the target surface. Large-scale craters produced by brittle conchoidal fractures associated with crashed zone, radial and lateral cracks, dominate the erosion process at large jet impact angles while small-scale craters involving micro-ploughing and micro-cutting are produced by the ductile mode erosion at small jet impact angles. The relation between the process parameters and the overall average volume of craters has also been quantitatively analyzed. A combination of small jet impact angle and abrasive particles and low water pressure is preferred for improving the surface quality after the ASJ machining process caused by the more formation of ductile mode induced craters on the target material, but it is at the sacrifice of the material removal rate as well.

  19. LixV2O5 - Analysis of surface reactions by spectroscopic quartz crystal mircogravimetry

    Science.gov (United States)

    Terwort, Jeroen; Berkemeier, Frank; Schmitz, Guido

    2016-12-01

    We investigate the electrochemical side reactions that occur during the cyclic lithiation/delithiation of sputter-deposited LixV2O5 films. For this purpose, the mass change of LixV2O5 films during lithiation/delithiation is measured by quartz crystal microgravimetry, while the electrical charge that is flowing during this reaction is measured by cyclic voltammetry. A time-resolved evaluation of the measurement data, in combination with an advanced type of data processing, finally allows us to calculate time-resolved quantitative mass spectra. These spectra provide information about the chemical species that take part during the electrochemical reactions. Based on this technique, we study the electrochemical side reactions between the LixV2O5 and the corresponding liquid electrolyte, i.e. we investigate the time-resolved formation of the solid electrolyte interface (SEI) layer during long term cycling. We are able to identify several chemical species that are formed during cycling and moreover, we identify three different stages of SEI formation.

  20. Detection and analysis of Bacillus subtilis growth with piezoelectric quartz crystal impedance based on starch hydrolysis.

    Science.gov (United States)

    Wu, Y; Xie, Q; Zhou, A; Zhang, Y; Nie, L; Yao, S; Mo, X

    2000-10-01

    A piezoelectric quartz crystal (PQC) impedance method based on the alpha-amylase-catalyzed hydrolysis of starch present in a culture medium has been developed for in situ monitoring of the whole growth process of Bacillus subtilis and the variation in the activity of alpha-amylase during bacterial growth. An S-shaped response behavior was observed for Deltaf(0), and simultaneously inverse S-shaped responses were found for DeltaR(1) and DeltaL(1). The ratio of DeltaR(1) to Deltaf(0) or DeltaL(1) coincided well with that calculated from Martin's equations reflecting the solution density-viscosity effect, suggesting that the continuing change in liquid loading onto the PQC surface causes significant variation in Deltaf(0), DeltaR(1), and DeltaL(1). Bacterial growth equations were derived from the kinetics of the enzyme-catalyzed hydrolysis of starch, which fit well with the experimental responses of Deltaf(0), DeltaR(1), and DeltaL(1). Kinetic parameters of bacterial growth, including the asymptote (A), the maximum specific growth rate (microm), and the lag time (lambda), were obtained and were in good agreement with those obtained from the pour plate count method. The variation in the activity of alpha-amylase exhibited peak-type behavior with its maximum value at the later stage of the log phase. In addition, the influence of initial bacterial concentration was also investigated.

  1. Effect of fluid motion on the impact erosion by a micro-particle on quartz crystals

    Directory of Open Access Journals (Sweden)

    D. H. Cai

    2016-08-01

    Full Text Available Abrasive slurry jet (ASJ is a promising technology to process a variety of materials with advantages of high flexibility, no heat affected zone and high cutting efficiency. In this paper, the impressions generated on a quartz crystal specimen by the impacts of micro-particles laden in a water flow and the associated impact erosion mechanisms are presented and discussed in order to effectively and efficiently control the machining quality. Both brittle and ductile mode erosions coexist in the machining process due to the influence of the fluid motion on the trajectories of particles near the target surface. Large-scale craters produced by brittle conchoidal fractures associated with crashed zone, radial and lateral cracks, dominate the erosion process at large jet impact angles while small-scale craters involving micro-ploughing and micro-cutting are produced by the ductile mode erosion at small jet impact angles. The relation between the process parameters and the overall average volume of craters has also been quantitatively analyzed. A combination of small jet impact angle and abrasive particles and low water pressure is preferred for improving the surface quality after the ASJ machining process caused by the more formation of ductile mode induced craters on the target material, but it is at the sacrifice of the material removal rate as well.

  2. Use of quartz crystal nanobalance to study the binding and stabilization of albumin and doxycycline on a thin layer of hydroxyapatite

    Energy Technology Data Exchange (ETDEWEB)

    Victor, Sunita Prem [Biosurface Technology Division, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum 695012, Kerala (India); Sharma, Chandra P., E-mail: sharmacp@sctmist.ac.in [Biosurface Technology Division, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum 695012, Kerala (India); Sreenivasan, K. [Biosurface Technology Division, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum 695012, Kerala (India); Laboratory for Polymer Analysis, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Trivandrum 695012, Kerala (India)

    2011-12-15

    This study reports the use of quartz crystal nanobalance (QCN) to study the adsorption of two model molecules namely albumin and doxycycline by hydroxyapatite (HA). The work focuses on the deposition of a stable coating of HA on the quartz crystal, modification of the coating using doxycycline and its subsequent effects on albumin adsorption. The uniformity and thickness of the HA coating has been studied using atomic force microscopy (AFM). The functional groups to ascertain the presence of the selected moieties have been characterized by Raman spectroscopy. The results indicate that the mass of albumin deposited on the surface of the HA coated quartz crystal functionalized with doxycycline shows a substantial increase when compared to the standard HA coated quartz crystal. The adsorbed albumin has also been found to be retained for an enhanced period of time. This surface immobilization of doxycycline and subsequent albumin adsorption seem to be a promising approach to confer biomaterials with antithrombogenic and antibacterial surfaces.

  3. Use of quartz crystal nanobalance to study the binding and stabilization of albumin and doxycycline on a thin layer of hydroxyapatite

    Science.gov (United States)

    Victor, Sunita Prem; Sharma, Chandra P.; Sreenivasan, K.

    2011-12-01

    This study reports the use of quartz crystal nanobalance (QCN) to study the adsorption of two model molecules namely albumin and doxycycline by hydroxyapatite (HA). The work focuses on the deposition of a stable coating of HA on the quartz crystal, modification of the coating using doxycycline and its subsequent effects on albumin adsorption. The uniformity and thickness of the HA coating has been studied using atomic force microscopy (AFM). The functional groups to ascertain the presence of the selected moieties have been characterized by Raman spectroscopy. The results indicate that the mass of albumin deposited on the surface of the HA coated quartz crystal functionalized with doxycycline shows a substantial increase when compared to the standard HA coated quartz crystal. The adsorbed albumin has also been found to be retained for an enhanced period of time. This surface immobilization of doxycycline and subsequent albumin adsorption seem to be a promising approach to confer biomaterials with antithrombogenic and antibacterial surfaces.

  4. Direct Growth of Graphene-like Films on Single Crystal Quartz Substrates

    Science.gov (United States)

    Samsonau, Siarhei

    Direct growth of graphene-like (GL) films (nano-crystalline graphite films) on single crystal quartz substrates by chemical vapor deposition (CVD) from methane and molecular beam growth (MBG) is reported. The GL films have been characterized by means of Raman spectroscopy, atomic force microscopy and electrical measurements. Raman spectroscopy reveals nanocrystalline structure of the films grown at different conditions. The thinnest CVD grown GL films obtained so far have a thickness of 1.5 nm, a relatively rough surface structure and electrical conductivity in the range of 20 kO/square. Low temperature Hall-effect measurements performed on these films have revealed that the major charge carriers are holes with mobility of 40 cm2/Vs at room temperature. While inferior to graphene in terms of electronic properties, the graphene-like films possess very high chemical sensitivity. Study of MBG grown films revealed formation of a non-conductive carbon layer of low crystallinity on the initial stage of the growth process. In order to study the influence of the quartz substrate on the film formation process we performed ab initio simulation of the MBG process. For this simulation we used an atom-by-atom approach, which, we believe, is a closer approximation to the real molecular beam deposition process reported so far. The simulation showed that the initial formation of the film follows the atomic structure of the substrate. This leads to a high content of sp3 hybridized atoms at the initial stage of growth and explains formation of a non-conductive film. Additionally, we demonstrated how a non-conductive film becomes conductive with the increase of the film thickness. These results agree fairly well with the data obtained by AFM, electrical, and Raman measurements conducted on the films grown by MBG. High chemical sensitivity of GL films has been demonstrated by measuring the change in their conductance during exposure to a NO2-containing atmosphere. Sensitivity of CVD

  5. ESEEM of industrial quartz powders: insights into crystal chemistry of Al defects

    Science.gov (United States)

    Romanelli, Maurizio; Di Benedetto, Francesco; Bartali, Laura; Innocenti, Massimo; Fornaciai, Gabriele; Montegrossi, Giordano; Pardi, Luca A.; Zoleo, Alfonso; Capacci, Fabio

    2012-06-01

    A set of raw industrial materials, that is, pure quartz and quartz-rich mixtures, were investigated through electron paramagnetic resonance and electron spin echo-envelope modulation spectroscopies, with the aim of evaluating the effective role played by defect centres and of assessing whether they can be used to monitor changes in the physical properties of quartz powders with reference to their health effects. The obtained results point to two interactions of the Al defect centres with H+, hosted in sites within the channels parallel and perpendicular to the c axis of quartz, respectively. These two Al/H+ (hAl) centres exhibit a weak chemical bond, and their relative amounts appear to be modified/controlled by the thermo-mechanical processes underwent by powders. Indeed, a mechanically promoted inter-conversion between the two kinds of site is suggested. As a consequence, the hAl centres are effective in monitoring even modest activations of powders, through thermal or mechanical processes, and they are also supposed to play a specific, relevant role in quartz reactivity during the considered industrial processes.

  6. Inductive effect of crystalline nucleus on the structure of its local environment in the process of quartz glass crystallization

    Science.gov (United States)

    Zolotarev, V. M.; Pan'kin, D. V.; Shimko, A. A.; Kasatkin, I. A.

    2015-12-01

    The morphology and the structural and chemical properties of crystalline formations appearing on the surface of commercial quartz glasses at the beginning of the induction stage upon heating at temperatures of 1000-1300°C are studied by optical polarization microscopy, μ-Fourier transform infrared spectroscopy, and X-ray diffraction. It is shown that crystalline island nuclei induce crystallization not only in the local environment of the surface layer, but also in the glass bulk at a depth of up to ≈200 μm. Crystalline nuclei in the center of islands often have an imperfect crystal structure formed by intermediate mesophases based on individual low-symmetry SiO4 tetrahedra. However, the induced phase at the periphery of these nuclei has a well-ordered crystal structure consisting mainly of α-SiO2 (quartz) and/or α-cristobalite. The proportion of these two phases depends on the glass heating temperature, namely, at 1000°C, the induced structure for the most part contains α-SiO2, while α-cristobalite dominates at 1300°C.

  7. Disposable micro-fluidic biosensor array for online parallelized cell adhesion kinetics analysis on quartz crystal resonators

    DEFF Research Database (Denmark)

    Cama, G.; Jacobs, T.; Dimaki, Maria

    2010-01-01

    In this contribution we present a new disposable micro-fluidic biosensor array for the online analysis of adherent Madin Darby canine kidney (MDCK-II) cells on quartz crystal resonators (QCRs). The device was conceived for the parallel cultivation of cells providing the same experimental conditions...... molding process was simulated in order to optimize the mold geometry and minimize the shrinkage and the warpage of the parts. MDCK-II cells were cultivated in the biosensor array. Parallel cultivation of cells on the gold surface of the QCRs led to first observations of the impact of the cell distribution...

  8. Using phonon resonances as a route to all-angle negative refraction in the far-infrared region: the case of crystal quartz.

    Science.gov (United States)

    Rodrigues da Silva, R; Macêdo da Silva, R; Dumelow, T; da Costa, J A P; Honorato, S B; Ayala, A P

    2010-10-15

    We consider how all-angle negative refraction may be induced in anisotropic crystals by making use of the phonon response. We investigate the example of crystal quartz at far-infrared wavelengths. Reflection and transmission measurements confirm the expected behavior, and show relatively high transmission efficiency at frequencies at which negative refraction occurs.

  9. Preparation of low-crystalline apatite nanoparticles and their coating onto quartz substrates.

    Science.gov (United States)

    Kawashita, Masakazu; Taninai, Koji; Li, Zhixia; Ishikawa, Kunio; Yoshida, Yasuhiro

    2012-06-01

    We prepared low-crystalline apatite nanoparticles and coated them onto a surface of a Au/Cr-plated quartz substrate by the electrophoretic deposition (EPD) method or by using a self-assembled monolayer of 11-mercaptoundecanoic acid (SAM method). Low-crystalline apatite nanoparticles around 10 nm in size with extremely low contents of undesirable residual products were obtained by adding (NH(4))(2)HPO(4) aqueous droplets into a modified synthetic body fluid solution that contained Ca(CH(3)COO)(2). The apatite nanoparticles were successfully coated by either the EPD method or the SAM method; the nanoparticle coating achieved by the SAM method was more uniform than that achieved by the EPD method. The present SAM method is expected to be a promising technique for obtaining a quartz substrate coated with apatite nanoparticles, which can be used as a quartz crystal microbalance device.

  10. New method to determine the optical rotatory dispersion of inorganic crystals applied to some samples of Carpathian Quartz.

    Science.gov (United States)

    Dimitriu, Dan Gheorghe; Dorohoi, Dana Ortansa

    2014-10-15

    A new method to determine the optical rotatory dispersion (ORD) in the visible range, based on a channeled spectrum obtained with a uniax inorganic crystal introduced between two crossed polarizers with its optical axis parallel to the light propagation direction is detailed in this paper. When the studied inorganic crystals are transparent, this method permits the estimation of the optical rotatory dispersion in the visible range, for which the cheap polarizers are available. The speed of the measurements is very high, because the estimations are made from the channeled spectrum obtained for a single arrangement of the optical components. By using a computer, ORD is quickly determined for the visible range. The results obtained by this method for some Carpathian Quartz samples are consistent with those from literature. The proposed method can be also applied in UV and IR spectral ranges, when the anisotropic layers are transparent and the linearly polarized radiations can be obtained.

  11. Electronic nose based on multipatterns of ZnO nanorods on a quartz resonator with remote electrodes.

    Science.gov (United States)

    Ko, Wooree; Jung, Namchul; Lee, Moonchan; Yun, Minhyuk; Jeon, Sangmin

    2013-08-27

    An electrodeless monolithic multichannel quartz crystal microbalance (MQCM) sensor was developed via the direct growth of ZnO nanorod patterns of various sizes onto an electrodeless quartz crystal plate. The patterned ZnO nanorods acted as independent resonators with different frequencies upon exposure to an electric field. The added mass of ZnO nanostructures was found to significantly enhance the quality factor (QF) of the resonator in electrodeless QCM configuration. The QF increased with the length of the ZnO nanorods; ZnO nanorods 5 μm in length yielded a 7-fold higher QF compared to the QF of a quartz plate without ZnO nanorods. In addition, the ZnO nanorods offered enhanced sensitivity due to the enlarged sensing area. The developed sensor was used as an electronic nose for detection of vapor mixtures with impurities.

  12. Ultrasensitive detection of streptomycin using flow injection analysis-electrochemical quartz crystal nanobalance (FIA-EQCN) biosensor.

    Science.gov (United States)

    Mishra, Geetesh K; Sharma, Atul; Bhand, Sunil

    2015-05-15

    This work presents the development of an ultrasensitive biosensor for detection of streptomycin residues in milk samples using flow injection analysis-electrochemical quartz crystal nanobalance (FIA-EQCN) technique. Monoclonal antibody specific to streptomycin was immobilized on to the thiol modified gold quartz crystal surface. A broad dynamic range (0.3-300 ng/mL) was obtained for streptomycin with a good linearity in the range 0.3-10 ng/mL for PBS and 0.3-50 ng/mL for milk. The correlation coefficient (R(2)) of the biosensor was found to be 0.994 and 0.997 for PBS and milk respectively. Excellent recoveries were obtained from the streptomycin spiked milk samples in the range 98-99.33%, which shows the applicability of the developed biosensor in milk. The reproducibility of the developed biosensor was found satisfactory with % RSD (n=5) 0.351. A good co-relation was observed between the streptomycin recoveries measured through the developed biosensor and the commercial ELISA kit. The analytical figures of merit of the developed biosensor confirm that the developed FIA-EQCN biosensor could be very effective for low-level detection of streptomycin in milk samples.

  13. An experimental study on the ultra-precision polishing of quartz crystal using MR fluids and micro abrasives

    Science.gov (United States)

    Kim, D. W.; Lee, J. W.; Cho, M. W.; Choi, S. B.

    2009-02-01

    This paper presents ultra-precision MR polishing results of quartz crystal, which has been widely used in many applications, such as piezo-electric transducer, surface acoustic wave (SAW) filters and SAW resonators, etc. It is known that smooth surface with sub-nanometer roughness is needed for higher-frequency application. The MR fluids, used for the polishing, consist of DI water based carbonyl iron (CI), nonmagnetic polishing micro abrasives, and required amount of stabilizers. In the process, mixed fluids were supplied into the gap between a rotating wheel (with electromagnetic field) and the workpiece. Then, the micro abrasives contained in the fluids perform material removal action from the workpiece. Such material removal mechanism in the MR polishing is considered as a process governed by the Bingham flow in the contact zone. In this study, material removal characteristics and generated surface roughness of the quartz crystal specimens using the MR polishing process were investigated through a series of experiments. The surface roughness variations of the polished specimens were investigated by changing imposed polishing conditions, such as wheel speed, magnetic field intensity. As a result, very fine surface roughness of Ra=0.770nm was obtained.

  14. Drug-Protein Interactions for Clinical Research by Nucleic Acid Programmable Protein Arrays-Quartz Crystal Microbalance with Dissipation Factor Monitoring Nanoconductometric Assay

    Directory of Open Access Journals (Sweden)

    Claudio Nicolini

    2014-01-01

    Full Text Available Conductometric monitoring of drug-gene and drug-protein interactions is of fundamental importance in the field of molecular pharmacology. Here, we present our main findings and characterizations of an important antiblastic used in neuro-oncology (Temozolomide, interacting with selected proteins that represent predictive biomarkers of the rate survival of the patients, of the outcome of chemotherapy and resistance to drug itself (namely, BRIP1 and MLH1. We use our previously introduced two genes along with previously described Nucleic Acid Programmable Protein Arrays (NAPPA-based nanoconductometric sensor. We performed a positive control (Temozolomide plus MLH1 protein, a negative control (Temozolomide plus BRIP1 protein and a multi-gene experiment (Temozolomide plus BRIP1&MLH1 being co-expressed, showing that we are able to properly perform pharmacoproteomics tasks, discriminating each protein and drug unique conductance curve as well as their interactions, even in the presence of multi-proteins being immobilized. Moreover, in the last part of our paper, we used a multiple regression model in order to predict the behavior of Temozolomide when exposed to BRIP1&MLH1 co-expressed and we showed that we are able to predict the drug-protein interaction profile with a good regression coefficient.

  15. In situ investigation of dye adsorption on TiO2 films using a quartz crystal microbalance with a dissipation technique

    KAUST Repository

    Harms, Hauke A.

    2012-01-01

    Dye adsorption plays a crucial role in dye-sensitized solar cells. Herein, we demonstrate an in situ liquid-phase analytical technique to quantify in real time adsorption of dye and coadsorbates on flat and mesoporous TiO 2 films. For the first time, a molar ratio of co-adsorbed Y123 and chenodeoxycholic acid has been measured. © 2012 the Owner Societies.

  16. Surfactant softening of plant leaf cuticle model wax--a Differential Scanning Calorimetry (DSC) and Quartz Crystal Microbalance with Dissipation (QCM-D) study.

    Science.gov (United States)

    Fagerström, Anton; Kocherbitov, Vitaly; Westbye, Peter; Bergström, Karin; Arnebrant, Thomas; Engblom, Johan

    2014-07-15

    The aim was to quantify the softening effect that two surfactants (C10EO7 and C8G1.6) have on a plant leaf cuticle model wax. Effects on the thermotropic phase behavior and fluidity of the wax (C22H45OH/C32H66/H2O) were determined. The model wax is crystalline at ambient conditions, yet it is clearly softened by the surfactants. Both surfactants decreased the transition temperatures in the wax and the G″/G' ratio of the wax film increased in irreversible steps following surfactant exposure. C10EO7 has a stronger fluidizing effect than C8G1.6 due to stronger interaction with the hydrophobic waxes. Intracuticular waxes (IW) comprise both crystalline and amorphous domains and it has previously been proposed that the fluidizing effects of surfactants are due to interactions with the amorphous parts. New data suggests that this may be a simplification. Surfactants may also absorb in crevices between crystalline domains. This causes an irreversible effect and a softer cuticle wax.

  17. Fabrication of SMD 32.768 kHz tuning fork-type crystals: photolithography and selective etching of an array of quartz tuning fork resonators

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S. [Dept. of Molecular Science and Technology, Ajou Univ., Suwon (Korea); Lee, J.Y.; Park, T.S. [Research and Development Center, Samsung Electro-Mechanics Co., Ltd., Suwon (Korea)

    2001-09-01

    Negative photoresist photolithography was used to etch array of quartz tuning forks for use in Qualcomm trademark mobile station modem (MSM)-3000{sup TM} central processing unit (CPU) chips of code division multiple access (CDMA), personal communication system (PCS), and global system for mobile communication (GSM) units. It was found superior to positive photoresist photolithography. Quartz tuning fork blanks with optimum shock-resistant characteristics were designed using finite element method (FEM) and processing condition was devised for reproducible precision etching of Z-cut quartz wafer into array of tuning forks. Tuning fork pattern was transferred via ordinary photolithographical chromium/quartz glass template using a standard single-sided aligner and subsequent negative photoresist development. Tightly adhering and pinhole-free 600/2000 A chromium/gold mask is coated over the developed photoresist pattern which was subsequently stripped in acetone. This procedure was repeated on the backside of the wafer. With protective metallization area of tuning fork geometry thus formed, etching through quartz wafer was done at 80 C in a {+-} 1.5 C controlled bath containing concentrated solution of ammonium bifluoride to remove unwanted area of the quartz wafer. Surface finish of quartz wafer prior to etching and the quality of quartz crystals used primarily affected the quality of quartz wafer surface finish after quartz etching. At 80 C, selective etching of 100 {mu}m quartz wafer could be effected within 90 min. Reproducible precision selective etching method has thus been established and enables mass production of miniature tuning fork resonators photolithographically. (orig.)

  18. Vacuum electrolysis of quartz

    Science.gov (United States)

    King, James Claude

    1976-01-13

    The disclosure is directed to a method for processing quartz used in fabricating crystal resonators such that transient frequency change of resonators exposed to pulse irradiation is virtually eliminated. The method involves heating the crystal quartz in a hydrogen-free atmosphere while simultaneously applying an electric field in the Z-axis direction of the crystal. The electric field is maintained during the cool-down phase of the process.

  19. Melt-inclusion-hosted excess 40Ar in quartz crystals of the Bishop and Bandelier magma systems

    Science.gov (United States)

    Winick, J.A.; McIntosh, W.C.; Dunbar, N.W.

    2001-01-01

    40Ar/39Ar experiments on melt-inclusion-bearing quartz (MIBQ) from the Bishop and Bandelier Tuff Plinian deposits indicate high concentrations of excess 40Ar in melt inclusions. Two rhyolite glass melt inclusion populations are present in quartz; exposed melt inclusions and trapped melt inclusions. Air-abrasion mill grinding and hydrofluoric acid treatments progressively remove exposed melt inclusions while leaving trapped melt inclusions unaffected. Laser step-heating of MIBQ yields increasing apparent ages as a function of exposed melt inclusion removal, reflecting the higher nonatmospheric 40Ar concentrations hosted in trapped melt inclusions. Exposed melt inclusion-free MIBQ from the Bishop, Upper Bandelier, and Lower Bandelier Tufts yield total-gas ages of 3.70 ?? 1.00 Ma, 11.54 ?? 0.87 Ma, and 14.60 ?? 1.50 Ma, respectively. We interpret these old apparent ages as compelling evidence for the presence of excess 40Ar in MIBQ. Trapped melt inclusions in sanidine phenocrysts may contain excess 40Ar concentrations similar to those in MIBQ. This excess 40Ar has the potential to increase single-crystal laser-fusion ages of sanidine by tens of thousands of years, relative to the actual eruption age.

  20. Tool wear of a single-crystal diamond tool in nano-groove machining of a quartz glass plate

    Science.gov (United States)

    Yoshino, Masahiko; Nakajima, Satoshi; Terano, Motoki

    2015-12-01

    Tool wear characteristics of a diamond tool in ductile mode machining are presented in this paper. Nano-groove machining of a quartz glass plate was conducted to examine the tool wear rate of a single-crystal diamond tool. Effects of lubrication on the tool wear rate were also evaluated. A numerical simulation technique was developed to evaluate the tool temperature and normal stress acting on the wear surface. From the simulation results it was found that the tool temperature does not increase during the machining experiment. It is also demonstrated that tool wear is attributed to the abrasive wear mechanism, but the effect of the adhesion wear mechanism is minor in nano-groove machining. It is found that the tool wear rate is reduced by using water or kerosene as a lubricant.

  1. Confocal Raman spectroscopy of island nuclei formed at the initial stage of quartz glass crystallization

    Science.gov (United States)

    Pankin, D. V.; Zolotarev, V. M.; Colas, M.; Cornette, J.; Evdokimova, M. G.

    2016-12-01

    Island nuclei formed on a polished quartz-glass surface upon heating to 1100°C have been investigated by confocal Raman spectroscopy. The structural and chemical composition of islands is shown to be a central nucleus, a shell around the nucleus, and a thin peripheral ring closing this shell. The formation and growth of individual regions of an island nucleus are found to occur in several stages. The shell around the nucleus is mainly formed by α-SiO2 and α-cristobalite nanoparticles with a size ≥40 nm, whereas the α-SiO2 nanoparticles in the nucleus and peripheral ring are 2-15 nm in size.

  2. Polyethylene Maleate Copolyesters as Coating Materials for Piezoelectric Quartz Crystal-based Chemical Sensors

    Directory of Open Access Journals (Sweden)

    D. C. Gupta

    2005-10-01

    Full Text Available Polyethylene maleate (PEM was synthesised by direct polycondensation of maleic anhydride and ethylene glycol in toluene under reflux usingp-toluene sulphonic acid as a catalyst. Structure of PEM was further modified by varying nature of diols and acid components, chain length of glycols, incorporation of aromatic and fluorine groups in the chain. Formation of PEM was monitored by gas chromatography. The parameters like degree of polymerisation, number average molecular weight (Mn, and weight average molecular weight (Mw were calculated from the extent of reaction and stoichiometric ratio of the reactants. The number average molecular weight was also determined using Knauer vapour pressure osmometer. Cohesive energy, volume, and solubility parameters of PEM-based copolyesters were calculated by group contribution method. These PEM-based copolyesters’ have been evaluated as sorbent-coating materials for the detection of organ0 phosphorus(OPcompo using dimethylmethylphosphonate (DMMP as model compound and piezoelectric crystal detector. PEMbisphenol A is found to be the most sensitive and potential coating material for the detection of OP compounds using piezoelectric crystal detector. Potential PEM-based copolyesters have been characterised by viscosity, infrared spectroscopy, NMR spectroscopy, Mn and thermal stability.

  3. Characterisation of a natural quartz crystal as a reference material for microanalytical determination of Ti, Al, Li, Fe, Mn, Ga and Ge

    Science.gov (United States)

    Audetat, Andreas; Garbe-Schonberg, Dieter; Kronz, Andreas; Pettke, Thomas; Rusk, Brian G.; Donovan, John J.; Lowers, Heather

    2015-01-01

    A natural smoky quartz crystal from Shandong province, China, was characterised by laser ablation ICP-MS, electron probe microanalysis (EPMA) and solution ICP-MS to determine the concentration of twenty-four trace and ultra trace elements. Our main focus was on Ti quantification because of the increased use of this element for titanium-in-quartz (TitaniQ) thermobarometry. Pieces of a uniform growth zone of 9 mm thickness within the quartz crystal were analysed in four different LA-ICP-MS laboratories, three EPMA laboratories and one solution-ICP-MS laboratory. The results reveal reproducible concentrations of Ti (57 ± 4 μg g-1), Al (154 ± 15 μg g-1), Li (30 ± 2 μg g-1), Fe (2.2 ± 0.3 μg g-1), Mn (0.34 ± 0.04 μg g-1), Ge (1.7 ± 0.2 μg g-1) and Ga (0.020 ± 0.002 μg g-1) and detectable, but less reproducible, concentrations of Be, B, Na, Cu, Zr, Sn and Pb. Concentrations of K, Ca, Sr, Mo, Ag, Sb, Ba and Au were below the limits of detection of all three techniques. The uncertainties on the average concentration determinations by multiple techniques and laboratories for Ti, Al, Li, Fe, Mn, Ga and Ge are low; hence, this quartz can serve as a reference material or a secondary reference material for microanalytical applications involving the quantification of trace elements in quartz.

  4. A Quartz Microbalance Study of the Electrosynthesis of Polypyrrole

    Science.gov (United States)

    1988-07-12

    electrochenmcal synthesis of conducting polymers onto an existing electrode substrate has become a popular method of preparing polymer modified electrodes... polythiophene . polypyrrole and poly(N-methylpyrrole) have been studied electrochemically using cyclic voltammetry (CV), chronocoulometry...indicative of electron transfer followed by an irreversible chemical reaction. This oxidation produces a continuous insoluble conducting polymer film on the

  5. Compositional analysis of electrodeposited bismuth telluride thermoelectric thin films using combined electrochemical quartz crystal microgravimetry--stripping voltammetry.

    Science.gov (United States)

    Ham, Sunyoung; Jeon, Soyeon; Lee, Ungki; Park, Minsoon; Paeng, Ki-Jung; Myung, Noseung; Rajeshwar, Krishnan

    2008-09-01

    Bismuth telluride (Bi 2Te 3 ) is a benchmark material for thermoelectric power generation and cooling applications. Electrodeposition is a versatile technique for preparing thin films of this material; however, it affords films of variable composition depending on the preparation history. A simple and rapid assay of electrodeposited films, therefore, has both fundamental and practical importance. In this study, a new protocol for the electroanalysis of Bi 2Te 3 thin films is presented by combining the two powerful and complementary techniques of electrochemical quartz crystal microgravimetry (EQCM) and stripping voltammetry. First, any free (and excess) tellurium in the electrodeposited film was reduced to soluble Te ( 2- ) species by scanning to negative potentials in a 0.1 M Na 2SO 4 electrolyte, and the accompanying frequency increase (mass loss) was used to determine the content of free tellurium. The film was again subjected to cathodic stripping in the same medium (to generate Bi (0) and soluble Te (2-) from the Bi 2 Te 3 film component of interest), and the EQCM frequency change was used to determine the content of chemically bound Te in the Bi 2Te 3 thin film and thereby the compound stoichiometry. Finally, the EQCM frequency change during Bi oxidation to Bi (3+) and the difference between total Bi and Bi in Bi 2Te 3 resulted in the assay of free (excess) Bi in the electrodeposited film. Problems associated with the chemical/electrochemical stability of the free Bi species were circumvented by a flow electroanalysis approach. Data are also presented on the sensitivity of electrodeposited Bi 2Te 3 film composition to the electrodeposition potential. This newly developed method can be used for the compositional analysis of other thermoelectric thin-film material candidates in general.

  6. Characteristic of SMD quartz crystal under high-g overload%SMD石英晶体抗高过载性能的研究

    Institute of Scientific and Technical Information of China (English)

    王岩; 沈瑞琪; 臧小为; 刘卫

    2015-01-01

    为了研究SMD石英晶体的抗高过载能力,采用自由式霍普金森压杆对7050、6035、5032、3225、3225(一级加固)、3225(二级加固)六种型号SMD石英晶体进行高过载环境下的动态加载测试。结果表明,在高过载条件下,SMD 石英晶体的抗高过载性能随尺寸减小而不断提高,并且产品经历高过载环境后电气参数的不良率逐步降低。未经过加固处理的各型号SMD石英晶体(7050、6035、5032、3225)经过高过载试验(50000~80000 g)后,电气参数均出现超差,不能满足武器系统的要求。经过加固处理的SMD石英晶体样品(3225一级加固、3225二级加固)经过高过载试验可以正常工作。%In order to study the anti-overload ability of SMD quartz crystal, the free Hopkinson pressure bar technology was performed to test the six SMD quartz crystals, including 7050, 6035, 5032, 3225, 3225 (primary reinforcement) and 3225 (secondary reinforcement), under high-g overload environment. Conclusions are that, under high-g overload environment, the anti-overload ability of SMD quartz crystal increases with its size decreasing, and the poor rate of electrical parameters after loading declines gradually. The electrical parameters of the SMD quartz crystal which were not reinforced appear ultra-poor, unable to satisfy the needs in weapon system. The SMD quartz crystal samples which were reinforced works very well after high-g overload experiment (50 000–80 000 g).

  7. Development of SMD 32.768 kHz tuning fork-type crystals using photolithography and selective etching process. Pt. I. Selective etching of an array of quartz tuning fork resonators

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S. [Samsung Electro-Mechanics Co., Ltd., Suwon City (Korea); Kang, K.M. [National Univ. of Technology, Seoul (Korea). Dept. of Materials Engineering

    2001-05-01

    Negative photoresist photolithography was found superior to previously used positive photoresist photolithography to etch array of quartz tuning forks for use in Qualcomm trademark mobile station modem (MSM), 3000{sup TM} central processing unit (CPU), chips of code division multiple access (CDMA), personal communication system (PCS), and global system for mobile communication (GSM) units. Optimum processing condition was devised for reproducible precision etching of Z-cut quartz wafer into array of tuning forks. Tuning fork pattern was transferred via ordinary photolithographical chromium/quartz glass template using a standard single-sided aligner and subsequent negative photoresist development. A tightly adhering and pinhole-free 600/2000 A chromium/gold mask is coated over the developed photoresist pattern which was subsequently stripped in acetone. This procedure was repeated on the backside of the wafer. With protective metallization area of tuning fork geometry thus formed, etching through quartz wafer was done at 80 C in a {+-} 1.5 C controlled bath containing concentrated solution of ammonium bifluoride to remove unwanted area of the quartz wafer. The quality of quartz wafer surface finish after quartz etching depended primarily on the surface finish of quartz wafer prior to etching and the quality of quartz crystals used. At 80 C, selective etching of 100 {mu}m quartz wafer could be effected within 90 min. Reproducible precision selective etching method has thus been established and enables mass production of miniature tuning fork resonators with electrode patterns on them photolithographically. (orig.)

  8. Fe(III) hydroxide nucleation and growth on quartz in the presence of Cu(II), Pb(II), and Cr(III): metal hydrolysis and adsorption.

    Science.gov (United States)

    Dai, Chong; Hu, Yandi

    2015-01-06

    Fe(III) hydroxide nanoparticles are an essential carrier for aqueous heavy metals. Particularly, iron hydroxide precipitation on mineral surfaces can immobilize aqueous heavy metals. Here, we used grazing-incidence small-angle X-ray scattering (GISAXS) to quantify nucleation and growth of iron hydroxide on quartz in 0.1 mM Fe(NO3)3 solution in the presence of Na(+), Cu(2+), Pb(2+), or Cr(3+) at pH = 3.7 ± 0.1. In 30 min, the average radii of gyration (R(g)) of particles on quartz grew from around 2 to 6 nm in the presence of Na(+) and Cu(2+). Interestingly, the particle sizes remained 3.3 ± 0.3 nm in the presence of Pb(2+), and few particles formed in the presence of Cr(3+). Quartz crystal microbalance dissipation (QCM-D) measurements showed that only Cr(3+) adsorbed onto quartz, while Cu(2+) and Pb(2+) did not. Cr(3+) adsorption changed the surface charge of quartz from negative to positive, thus inhibiting the precipitation of positively charged iron hydroxide on quartz. Masses and compositions of the precipitates were also quantified. This study provided new insights on interactions among quartz, iron hydroxide, and metal ions. Such information is helpful not only for environmental remediation but also for the doping design of iron oxide catalysts.

  9. Protein Adsorption Behavior of Synthetic Macromolecules Based on Quartz Crystal Macrobaiance%基于QCM-D技术的合成高分子对蛋白的吸附行为

    Institute of Scientific and Technical Information of China (English)

    张奕; 曾戎; 周长忍

    2009-01-01

    The surface topography, hydrophobicity, hydrated process and protein adsorption behavior of poly (lactic acid), polycarbonate and polymethylmethacrylate were investigated with the quartz crystal microbalance (QCM) with dissipation monitoring and atomic force microscopy (AFM) techniques. The result reveals that: with the hydrophobicity of film increased, protein adsorbed amount increases while viscoelastic property of protein layer adsorbed decreases. There are two types of protein adsorbed on the surface: one is reversible, another is irreversible. The reversible part will be resolved into phosphate buffered solution(PBS) after rinsing, however the irreversible part will remain on the films with the changed conformation and more rigid property. Langmuir model is found to fit with the protein adsorption dynamics curves well. The result shows that adsorption rate constant increases with the hydrophobicity of films.%采用AFM(原子力显微镜)和QCM-D(带损耗测量的石英晶体微天平)等技术研究了聚乳酸、聚碳酸酯和聚甲基丙烯酸甲酯三种合成高分子材料经旋转成膜后的袁面形貌、亲疏水性、水合过程及蛋白吸附行为.结果发现,薄膜的疏水性越强,蛋白吸附量越多,蛋白层的粘弹性越小;且吸附在材料表面的蛋白分为可逆吸附和不可逆吸附两部分,可逆部分可被PBS(磷酸盐缓冲溶液)洗脱,而不可逆吸附蛋白由于在疏水力作用下构象发生变化,变得致密无法脱附,粘弹性比发生可逆吸附的蛋白更小.用Langmuir吸附速率方程可较好地拟合薄膜的蛋白吸附动力学曲线,发现薄膜疏水性越强,白蛋白吸附速率越快.

  10. The calculation of active Raman modes of -quartz crystal via density functional theory based on B3LYP Hamiltonian in 6–311+G(2d) basis set

    Indian Academy of Sciences (India)

    M Talebian; E Talebian; A Abdi

    2012-05-01

    We obtained an approximation of the force field of -quartz crystal using a new idea of applying density functional theory [J Purton, R Jones, C R A Catlow and M Leslie, Phys. Chem. Minerals 19, 392 (1993)]. Our calculations were based on B3LYP Hamiltonian [A N Lazarev and A P Mirgorodsky, Phys. Chem. Minerals 18, 231 (1991)] in 6−311+G(2d) basis set for H16Si7O6 cluster and included a unit cell of the lattice. The advantage of our method is the increase in the speed of calculations and the better adaption of simulation results with the experimental data.

  11. Effect of inorganic positive ions on the adsorption of surfactant Triton X-100 at quartz/solution interface

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The electrode-separated piezoelectric sensor (ESPS), an improved setup of quartz crystal microbalance (QCM), has been employed to investigate the adsorption behavior of nonionic surfactant Triton X-100 at the hydrophilic quartz-solution interface in mineralized water medium in situ, which contained CaCl2 0.01 mol·L?1, MgCl2 0.01 mol·L?1, NaCl 0.35 mol·L?1. In a large scale of surfactant concentration, the effects of Ca2+, Mg2+ and Na+ on the adsorption isotherm and kinetics are obviously different. In aque-ous solution containing NaCl only, adsorption of Triton X-100 on quartz-solution interface is promoted, both adsorption rate and adsorption amount increase. While in mineralized water medium, multivalent positive ions Ca2+ and Mg2+ are firmly adsorbed on quartz-solution interface, result in the increasing of adsorption rate and adsorption amount at low concentration of surfactant and the peculiar desorption of surfactant at high concentration of Triton X-100. The results got by solution depletion method are in good agreement with which obtained by ESPS. The "bridge" and "separate" effect of inorganic positive ions on the adsorption and desorption mechanism of Triton X-100 at the quartz- solution interface is discussed with molecular dynamics simulations (MD), flame atomic absorption spectrometry (FAAS) and atomic force microscopy (AFM) methods.

  12. Crystallization and uplift path of late Variscan granites evidenced by quartz chemistry and fluid inclusions: Example from the Land's End granite, SW England

    Science.gov (United States)

    Drivenes, Kristian; Larsen, Rune Berg; Müller, Axel; Sørensen, Bjørn Eske

    2016-05-01

    The megacrystic, coarse-grained granite of the Land's End granitic complex, SW England, has been investigated by analyzing fluid inclusions, trace elements, and cathodoluminescence textures of quartz. By applying the TitaniQ geothermobarometer together with the cathodoluminescence textures, a two-stage emplacement process is proposed. K-feldspar and quartz phenocrysts crystallized in a deep magma chamber at ca. 18-20 km depth. The phenocrysts were transported together with the melt to a shallow emplacement depth at ca. 5-9 km in multiple intrusive events, causing the composite appearance of the granitic complex. This model of emplacement concurs with similar granites from the Erzgebirge. At the emplacement level, the magma exsolved an aqueous fluid with average salinity of 17.3% m/m NaCl and 9.7% m/m CaCl2. Fluids with higher salinities were exsolved deeper in the system, as the magma experienced stages of water saturation and water undersaturation during ascent from the deep magma chamber. The complex fluid inclusion textures are the results of multiple stages of entrapment of aqueous fluids in the host phases as multiple recharge events from the deeper magma chamber supplied fresh melts and aqueous volatiles. Titanium contents in quartz are closely related to the panchromatic cathodoluminescence intensity, and the Al/Ti ratio is reflected by the 3.26 eV/2.70 eV ratio of hyperspectral cathodoluminescence.

  13. Research on Development Trends of Quartz Crystal Oscillator%石英晶体振荡器的发展趋势研究

    Institute of Scientific and Technical Information of China (English)

    伍华林; 吕延; 吕明

    2013-01-01

    This paper analyzes the development status of the quartz crystal oscillator at home and abroad, technology trends and market prospects. The results show that the current quartz crystal oscillator is moving trends of chip-based integration and environmental protection, and SMT products will increasingly become the market mainstream products, which is widely used in fields converged communications, navigation, satellite, radar and mapping, the demand is rapid growth with 38% per annum, the future has a broad market space.%本文叙述和分析了石英晶体振荡器的国内外发展现状、技术发展趋势和市场前景.结果表明目前石英晶体振荡器正朝着型化、片式化、集成化和环保的趋势发展,表面贴装式的产品将日益成为市场的主流产品,广泛应用于融合通信、导航、卫星、雷达、测绘等领域,需求量以每年38%快速增长,未来具有广阔的市场空间.

  14. The Quartz Analog Watch: A Wonder Machine.

    Science.gov (United States)

    Crane, H. Richard, Ed.

    1993-01-01

    Summarizes how a quartz watch works. Discusses the quartz crystal, its form, and how its frequency is set to a standard; the integrated circuit chip that drives the crystal in vibration, scales its frequency down, and forms pulses that turn the motor; and the motor that drives the gear train that turns the hands. (ZWH)

  15. Binding studies of L-tryptophan to human serum albumin with nanogold-structured sensor by piezoelectric quartz crystal impedance analysis.

    Science.gov (United States)

    Long, Yumei; Yao, Shouzhuo; Chen, Jinhua

    2011-12-01

    Nanogold-modified sensor was constructed and applied to study the binding of L-tryptophan to human serum albumin (HSA) in situ by piezoelectric quartz crystal impedance (PQCI) analysis. It was interesting that the as-prepared nanogold modified sensor was more sensitive and biocompatible than bare gold electrode. The frequency changes due to protein adsorption on the nanogold-modified sensor might be described as a sum of two exponential functions and detailed explanation was given. Additionally, the kinetics of the binding process was also investigated. The binding constant (K) and the number of binding site (n) for the binding process without competitor are fitted to be 1.07 x 10(4) (mol l(-1))(-1) s(-1) and 1.13, respectively, and 2.24 x 10(3) (mol l-(1))(-1) s(-1) and 1.18, respectively for the binding process with competitor.

  16. New features of different frequency generating systems due to the use of electrodeless rigidly mounted VBA quartz crystal resonator

    Science.gov (United States)

    Jendly, A.; Graf, E.; Busca, G.; Brownsea, D. A.

    1984-01-01

    The BVA 5 MHz crystal equipped frequency sources exhibit a new blend of performances such as 10 to 11 daily stability, 5x10-13 short term stability (1 to 30 s time intervals) and close to the carrier low phase noise (1 Hz : -120 dBc, 10 Hz : -140 dBc), whereby retaining the customary crystal oscillator benefits of small volume, high reliability and low price, as opposed to more sophisticated frequency generators which would be required to achieve comparable performances. Examples illustrating the impact of the Oscilloquartz BVA oven-controlled crystal oscillator in different frequency generating systems are presented: cesium frequency standards; hydrogen frequency standard; a precision distribution sub-system for satellite ground stations; and high hierarchy exchanges of digital networks, synchronized by the master-slave method are discussed.

  17. OSL and photo-transferred TL of quartz single crystals sensitized by high-dose of gamma-radiation and moderate heat-treatments.

    Science.gov (United States)

    Ferreira de Souza, Leonardo B; Guzzo, Pedro L; Khoury, Helen J

    2014-12-01

    This study investigates the optically stimulated luminescence (OSL) and the photo-transferred thermoluminescence (PTTL) signals in quartz single crystals showing a strong TL peak near 300°C after being sensitized by irradiation with 25kGy of gamma rays and heating at 400°C. Natural and sensitized samples were prepared from two crystals with different sensitivity levels in the 300°C TL region. Continuous-wave (CW) and linearly-modulated (LM) OSL signals were stimulated with blue light-emitting diodes during 40 and 1000s, respectively. Two components were isolated from the CW-OSL signals of sensitized samples. These components were clearly seen in LM-OSL measurements together with two long-term components. LM-OSL showed that the sensitization process considered in this study sensitized an ultrafast OSL component of these crystals. The similar behavior found for the thermal stabilities of OSL and TL signals and the dependence of these signals with sample origins suggested that the trapping site related to the ultrafast component is also related to the TL process of the sensitized peak. The PTTL signal induced by blue LEDs increased the intensity of the sensitized glow peak. On the other hand, a remarkable reduction in the intensity of this peak as a result of the accumulated effect of blue light exposure was clearly seen in both kinds of crystals. These results were explained by a mechanism of competition between optically unstable deep traps and trap levels responsible to the sensitized TL peak. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Investigation of planar channeling radiation on diamond and quartz crystals at electron energies between 14 and 34 MeV and probing the influence of ultrasonic waves on channeling radiation

    Energy Technology Data Exchange (ETDEWEB)

    Azadegan, B.

    2007-11-15

    Measurements of planar channeling radiation (CR) have been performed at the electron beam of ELBE within an energy range between 14 and 34 MeV and for thicknesses of the diamond crystals between 42.5 and 500 {mu}m. Absolute CR photon yields have for the first time been obtained for the above given ranges of electron energy and crystal thickness. The square-root dependence of the planar CR photon yield on the thickness of diamond crystals has been confirmed. A systematic quantitative investigation of the influence of the crystal thickness on the CR line shape has for the first time been performed. The mean-squared multiple-scattering angle effective for planar CR observed in forward direction has been found to be weaker as assumed from scattering in amorphous targets. Scaling laws deduced from the measured CR data are of advantage for the operation of a CR source. The second part of this thesis deals with the possibility of stimulation of CR emission by means of ultrasonic vibrations excited in a piezoelectric single crystal. Since the knowledge of the CR spectra generated on undisturbed quartz crystals is a necessary precondition for some investigation of the influence of US, planar CR has for the first time been measured at medium electron energies for a variety of planes in quartz. As a consequence of the hexagonal structure of this crystal, relative intense CR could be registered even out of planes with indices larger than one. On the base of the non-linear optics method, occupation functions and spectral distributions of planar CR have been calculated for channeling of 20 MeV electrons in the (01 anti 15) plane of a 20 {mu}m thick quartz crystal at resonant influence of ultrasound (US). The resonance frequencies have been deduced from the measurements of CR spectra performed on quartz. First experimental investigations of the influence of US on CR started at ELBE aimed at the study of the effect of non-resonant ultrasonic vibrations excited in a 500 {mu}m thick

  19. Tourmalines from the siderite-quartz-sulphide hydrothermal veins, Gemeric unit, western Carpathians, Slovakia: crystal chemistry and evolution

    Science.gov (United States)

    Bačík, P.; Uher, P.; Dikej, J.; Puškelová, Ľ.

    2017-03-01

    Tourmaline is an important gangue mineral in a large number of Cretaceous siderite-quartz-sulphide hydrothermal veins in the Gemeric Unit, Slovak Ore Mountains, Slovakia, such as Dobšiná, Vlachovo, Rožňavské Bystré, Hnilčík, Rakovnica, Novoveská Huta, Gretla, Rudňany, and Bindt. In this study we combine by electron microprobe analysis, powder X-ray diffraction, Mössbauer and optical emission spectroscopy to determine the range of tourmaline compositions in the deposits and constrain the mechanisms of its precipitation. Selected samples from the mentioned deposits belong mostly to the alkali group, schorl to dravite series, rarely dominant X-site vacant foititic tourmaline (Vlachovo and Bindt) and oxy-dravite compositions (Hnilčík) were detected. Rim zones of some schorlitic tourmalines show high concentrations of Ti (up to 2.35 wt.% TiO2, 0.30 apfu; Rožňavské Bystré). The chemical composition is mostly controlled by alkali-deficient X □AlNa-1(Mg,Fe2+)-1 and proton-deficient AlO(Mg,Fe2+)-1(OH)-1 substitutions. Titanium is incorporated into the structure by Y Ti Y (Mg,Fe) Y Al-2, Y Ti Z Mg Y Al-1 Z Al-1, Y TiO( Y AlOH), and X Ca Y Ti Z MgO2 X □-1 Y,Z Al-2(OH)-2 substitutions. Along trace elements, Sr and V attain concentrations of 80-450 and 70-320 ppm, respectively. The unit-cell parameter a varies between 15.960 and 15.985 Å; variations in c are larger, between 7.177 and 7.236 Å indicating the presence of Fe3+ and Mg2+ at Z site. Mössbauer spectroscopy has shown variable Fe3+ proportions (0.17-0.55 apfu) in all samples. The gathered dataset suggests some qualitative considerations on the mechanisms controlling tourmaline compositions at the regional scale. The highest Fe3+ concentrations occur in samples from Rudňany and Gretla in the external part of Gemeric unit, suggesting higher oxidation during longer transport of fluids. We propose that the determined XFe in the samples are correlated with the compositions of the host rocks, as

  20. A Study on Detection of the CP4-EPSPs Protein with Quartz Crystal Microbalance Technology%石英晶体微天平对CP4-EPSPs草甘膦抗性蛋白检测研究

    Institute of Scientific and Technical Information of China (English)

    蔡淼; 岳喜庆; 黄新

    2014-01-01

    为建立5-烯醇式丙酮酸-3-磷酸合酶(CP4-EPSPs)蛋白的石英晶体微天平(QCM)传感检测方法,采用在金片表面修饰抗原所对应的单克隆抗体的方法,利用QCM技术,对CP4-EPSPs蛋白进行检测研究.结果表明:该方法灵敏度达到500ng·mL-1,特异性好,重复性高,检测转基因玉米含量检出限为0.1%.该方法不足之处在于检测仪器不方便携带,在未来研究中考虑研发便携式QCM检测装置.

  1. An electrochemical quartz crystal impedance study on anti-human immunoglobulin G immobilization in the polymer grown during dopamine oxidation at an Au electrode.

    Science.gov (United States)

    He, Hua; Xie, Qingji; Yao, Shouzhuo

    2005-09-15

    The polymeric film grown during dopamine oxidation at an Au electrode was studied as a novel matrix for immobilizing anti-human immunoglobulin G (IgG) via the electrochemical quartz crystal impedance analysis (EQCIA) method. The growth of the polymeric films at Au electrodes during dopamine oxidation in neutral phosphate buffer (pH 7.4) and the immobilization of anti-human IgG into the polymeric films during their growth have been traced at real time. Lysozyme control experiments suggested that anti-human IgG was electrostatically incorporated into the polymeric film. Also, the porosity of the polymeric films has been discussed by measuring the "wet" and "dry" frequency shifts. Compared with a polypyrrole film immobilized with anti-human IgG, the proposed matrix possessed a larger amount of specific binding sites for human IgG by subsequent immunoreaction tests. The association constant of the anti-human IgG immunoreaction was obtained with satisfactory results.

  2. In Situ Monitoring of the Generation of Monodisperse Silica Particles during the Hydrolysis of Tetraethyl Orthosilicate with Piezoelectric Quartz Crystal Impedance Analyzer

    Institute of Scientific and Technical Information of China (English)

    姚守拙; 张友玉; 谢青季

    2003-01-01

    The piezoelectric quartz crystal(PQC)impedance analyzer was used to monitor in situ the generation of monodisperse silica particles during the hydrolysis of tetraethyl orthosilicate (TEOS) and their adsorption onto and Au electrode in alcohol solutions containing water(6-15mol/L)and ammonia(0.2-2.0 mol/L).The equivalent circuit parameters,the resonance frequencies and the half-peak width values of the conductance spectra of the PQC resonance were obtained.The resonant frequency decreased notably while the motional resistance changed very slightly(within 1Ω during the hydrolysis reaction,suggesting that the mass effect dominated the adsorption of generated monodisperse silica particles on the gold electrode in this system.Changes in f0 indicated that the ammonia concentration affected the hydrolytic reaction obviously,and the influence of water concentration on the reaction was small while the water was significantly excessive.Kinetics of monodisperse silica particle adsorption occurring at the electrode i solution interface was analyzed using a first-order reaction scheme.In addition,the electrolyte-induced precipitation of the monodisperse silica of adsorbed particles per area and the converge of monodisperse silica particles were obtained from scanning electron nicroscope(SEM)observations.

  3. Application of quartz crystal nanobalance for simultaneous determination of vanillylmandelic and homovanillic acids by a net analyte signal-based method.

    Science.gov (United States)

    Shojaei, Maryam; Mirmohseni, Abdolreza; Omidi, Yadollah; Farbodi, Maryam

    2009-10-01

    Homovanillic acid (HVA) and vanillylmandelic acid (VMA) were selectively determined by quartz crystal nanobalance sensor in conjunction with net analyte signal (NAS)-based method called HLA/GO. An orthogonal design was applied for the formation of calibration and prediction sets including HVA, VMA, and some common and structurally similar urine compounds. The selection of the optimal time range involved the calculation of the NAS regression plot in any considered time window for each test sample. The searching of a region with maximum linearity of NAS regression plot (minimum error indicator) and minimum of predicted error sum of squares value was carried out by applying a moving window strategy. Based on the obtained results, the differences on the adsorption profiles in the time range between 1 and 300 s were used to determine mixtures of compounds by HLA/GO method. Several figures of merit like selectivity, sensitivity, analytical sensitivity, and limit of detection were calculated for both compounds. The results showed that the method was successfully applied for the determination of VMA and HVA.

  4. Fluid-rock interaction controlling clay-mineral crystallization in quartz-rich rocks and its influence on the seismicity of the Carboneras fault area (SE Spain)

    Science.gov (United States)

    Jimenez-Espinosa, R.; Abad, I.; Jimenez-Millan, J.; Lorite-Herrera, M.

    2009-04-01

    The Carboneras Fault zone is one of the longest fault in the Betic Cordillera (SE Spain) and it would be a good candidate to generate large magnitude earthquakes (Gracia et al., 2006). Seismicity in the region is characterised by low to moderate magnitude events, although large destructive earthquakes have occurred, which reveals significant earthquake and tsunami hazards (Masana et al., 2004). Due to the internal architecture of the fault zone, shear lenses of post-orogenic sediments of Miocene and Pliocene age including marls and sandstones sequences are juxtaposed to the predominant slaty gouges of the Alpine basement. Microcataclasites and gouges of the quartz-rich post-orogenic sediments are also developed as cm- to m-scale bands, allowing the comparison between the deformed materials and their protoliths. Red, yellow and white sandstones and their respective cataclasites can be identified. This communication is concerned with the clay mineral crystallization events in these materials and its possible influence on the seismicity model of the region. The presence of phyllosilicates in fault zones as either neoformed or inherited clays is commonly related with fluid circulation and a mechanically weak fault behaviour (e.g., Wang, 1984). A critical factor for the understanding of the mechanical role of clays in fault rocks is to determine the timing of formation of mineral assemblages and microstructure of fault rocks and protolith. The effects of post-faulting alteration limit inferences about fault behaviour that can be made from exhumed rocks. The Carboneras fault zone provides good opportunities to study mineral processes enhanced by deformation, given that it is located in a region of arid climate and shows outcroppings of quartzitic rocks included in slaty rocks. Combined XRD, optical microscopy and SEM analyses reveal that deformed quartzitic rocks are enriched in phyllosilicates, increasing especially the amount of chlorite. The samples strongly damaged

  5. Electronic dipole resonance in smoky quartz

    NARCIS (Netherlands)

    Kerssen, J.; Volger, J.

    1967-01-01

    Microwave absorption in smoky quartz mono-crystal is ascribed to resonance transitions of trapped electrons between initially configurational degenerated states, which are Stark-splitted by a polarizing electric field.

  6. Intensity of quartz cathodoluminescence and trace-element content in quartz from the porphyry copper deposit at Butte, Montana

    Science.gov (United States)

    Rusk, B.G.; Reed, M.H.; Dilles, J.H.; Kent, A.J.R.

    2006-01-01

    Textures of hydrothermal quartz revealed by cathodoluminescence using a scanning electron microscope (SEM-CL) reflect the physical and chemical environment of quartz formation. Variations in intensity of SEM-CL can be used to distinguish among quartz from superimposed mineralization events in a single vein. In this study, we present a technique to quantify the cathodoluminescent intensity of quartz within individual and among multiple samples to relate luminescence intensity to specific mineralizing events. This technique has been applied to plutonic quartz and three generations of hydrothermal veins at the porphyry copper deposit in Butte, Montana. Analyzed veins include early quartz-molybdenite veins with potassic alteration, pyrite-quartz veins with sericitic alteration, and Main Stage veins with intense sericitic alteration. CL intensity of quartz is diagnostic of each mineralizing event and can be used to fingerprint quartz and its fluid inclusions, isotopes, trace elements, etc., from specific mineralizing episodes. Furthermore, CL intensity increases proportional to temperature of quartz formation, such that plutonic quartz from the Butte quartz monzonite (BQM) that crystallized at temperatures near 750 ??C luminesces with the highest intensity, whereas quartz that precipitated at ???250 ??C in Main Stage veins luminesces with the least intensity. Trace-element analyses via electron microprobe and laser ablation-ICP-MS indicate that plutonic quartz and each generation of hydrothermal quartz from Butte is dominated by characteristic trace amounts of Al, P, Ti, and Fe. Thus, in addition to CL intensity, each generation of quartz can be distinguished based on its unique trace-element content. Aluminum is generally the most abundant element in all generations of quartz, typically between 50 and 200 ppm, but low-temperature, Main Stage quartz containing 400 to 3600 ppm Al is enriched by an order of magnitude relative to all other quartz generations. Phosphorous

  7. An Eletrochemical Quatrz Crystal Microbalance Study on Electrochemical Behavior of As(Ⅲ)at Au/Au and Pt/Au Electrodes%电镀铂/金的金电极上As(Ⅲ)电化学行为的电化学石英晶体微天平研究

    Institute of Scientific and Technical Information of China (English)

    黄素清; 黄钊; 谷铁安; 谢青季; 姚守拙

    2011-01-01

    Electrochemical behavior of As(Ⅲ)at Au/Au and Pt/Au electrodes was investigated with an electrochemical quartz crystal microbalance (EQCM) in Britton-Robinson ( B-R, pH = 1. 8 - 11. 2)buffer solutions and in 0. 1 or 0. 5 mol/L aqueous H2SO4. Through real-time process monitoring of the EQCM parameters (frequency etc. ) and enhancement of the electrode-response signals by pre-electrodeposition of As (0) , the electrodeposition of As (0) , the electrod-esurface-adsorption characteristics of As(Ⅲ) and As(Ⅴ) , and the pH-dependence of the electrochemistry of As species were investigated. The following main conclusions are reached: (1) electrodeposition of As(0) can occur on both electrodes, but electrodeposition of As(0) on Pt/Au is more significant, and the electrooxidation of As(0) electrodeposited on Pt/Au at sufficient quantity can exhibit two current peaks for oxidation of outer-layer As(0) followed by inner-layer As(0); (2) As(Ⅲ) can strongly adsorb on Pt/Au but its oxidation product as As(Ⅴ) can desorb from the electrode surface , and the adsorption of both As(Ⅲ) and As(Ⅴ) is very weak on Au/Au; (3) the electrooxidation current of As(Ⅲ) on Pt/Au tends to be the maximum in pH = 1. 8 B-R buffer solution and in 0.1 mol/L aqueous H2SO4. Based on the pre-adsorption of As(Ⅲ) on Pt/Au and its catalyzed electrooxidation stripping, we proposed a new linear sweep voltammetric electroanalysis method for the determination of As (Ⅲ) , by which the detection sensitivity for As(Ⅲ) can be 40-fold enhanced over the pre-adsorption-free case%采用电化学石英晶体微天平(EQCM)技术研究了Britton-Robinson(B-R,pH=1.8~11.2)缓冲溶液和H2SO4介质中电镀铂淦的金电极上As(Ⅲ)的循环伏安行为.通过实时监测EQCM频率等参数的变化过程并利用预电沉积As(O)放大电极响应信号,考察了两电极上As.(O)的电沉积、AsⅢ皿和AsⅤ助组分的吸附特性以及As组分电化学行为的pH依赖性.主要结论如

  8. Design of two-channel phase discriminator applied to quartz crystal test%用于石英晶体测试的双通道鉴相系统设计

    Institute of Scientific and Technical Information of China (English)

    王晓彦; 李东; 王艳林

    2015-01-01

    为提高石英晶体的测试效率,搭建了双独立通道的鉴相系统。该系统采用同一DDS信号源同时激励两个π网络电路,设计了两个独立的鉴相电路,可实现两个通道同时鉴相。该系统采用差频鉴相的方法,使用AD8302作为鉴相器件,在提高鉴相的效率的同时确保了π网络零相位法的检测精度。为验证其可行性,将该系统应用到石英晶体电参数测量系统中。该双独立通道鉴相系统的频率测试范围为1~200 MHz,实验结果表明,鉴相精度达到±1°,满足石英晶体的测试需要。%In order to improve the measuring efficiency of quartz crystal,a two⁃channel phase discriminator system applied to quartz crystal test is designed. One DDS signal generator are used in the system to inspire two π⁃network circuits. The two in⁃dependent phase discriminator circuits are designed to discriminate the phase of two channels simultaneously. The difference fre⁃quency phase discriminating method is adopted in the system. The AD8302 is taken as a phase discriminator,which can im⁃prove the testing efficiency and ensure the testing precision simultaneously. In order to verify the viability of two⁃channel phase discriminator,it was used in a electrical parameter measuring system for quartz crystal test. The testing range of the two⁃channel phase discriminator system is 1~200 MHz. The experiment result shows that its phase discrimination accuracy is ±1°,which can meet the testing needs of quartz crystal.

  9. The role of quartz in the origin of optical activity on earth.

    Science.gov (United States)

    Evgenii, K; Wolfram, T

    2000-10-01

    A thorough analysis of literature data on distribution of right and left quartz in many locations on the surface of Earth indicates that quartz enantiomorph crystals are distributed in equal amounts in all locations. Therefore optically active quartz crystals of one or the other enantiomorph could not serve as the source of homochirality in the evolution of biosphere. Hence the calculation of a PVED based on published 'small excess of left quartz crystals' on Earth lacks a sound physical basis.

  10. Gyroscopic Inertial Micro-Balance Azimuth Locator (GIMBAL) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Research Support Instruments, Inc. (RSI) proposes the Gyroscopic Inertial Micro-Balance Azimuth Locator (GIMBAL) program to use an innovative encapsulated spinning...

  11. High Frequency Quartz Micro Balances: A Promising Path to Enhanced Sensitivity of Gravimetric Sensors

    Directory of Open Access Journals (Sweden)

    Jean M.J. Frèchet

    2006-04-01

    Full Text Available An array of 50 MHz quartz microbalances (QMBs coated with a dendronizedpolymer was used to detect small amounts of volatile organic compounds (VOCs in the gasphase. The results were compared to those obtained with the commonly used 10 MHzQMBs. The 50 MHz QMBs proved to be a powerful tool for the detection of VOCs in thegas phase; therefore, they represent a promising alternative to the much more delicatesurface acoustic wave devices (SAWs.

  12. Simulation of quartz resonators

    Science.gov (United States)

    Weinmann, M.; Radius, R.; Mohr, R.

    Quartz resonators are suitable as novel sensor elements in the field of profilometry and three dimensional measurement techniques. This application requires a tailoring of the oscillator circuit which is performed by a network analysis program. The equivalent network parameters are computed by a finite element analysis. The mechanical loading of the quartz is modeled by a viscous damping approach.

  13. Radiation Damage of Quartz Fibers

    CERN Document Server

    Hagopian, V

    1999-01-01

    Quartz fibers are used in high energy physics experiments as the active medium in high radiation area calorimetry. Quartz fibers are also used in the transmission of optical signals. Even though quartz does not damage by moderate amounts of irradiation, the clad of the fibers and the protective coating ( buffer) do damage reducing light transmission. Various types of quartz fibers have been irradiated and measured for light transmission. The most radiation hard quartz fibers are those with quartz clad and aluminum buffer.

  14. QUARTZ FIBER ELECTROSCOPES

    Science.gov (United States)

    Henderson, R.P.

    1957-09-17

    An instrument carried unobtrusively about the person such as in a finger ring to indicate when that person has been exposed to an unusual radiation hazard is described. A metallized quartz fiber is electrically charged to indicate a full scale reading on an etched glass background. The quartz fiber and the scale may be viewed through a magnifying lens for ease of reading. Incident radiation will ionize gaseous particles in the sealed structure thereby allowing the charge to leak off the quartz fiber with its resulting movement across the scale proportionally indicating the radiation exposure.

  15. Trace elements in quartz shed light on sediment provenance

    Science.gov (United States)

    Ackerson, Michael R.; Tailby, Nicholas D.; Watson, E. Bruce

    2015-06-01

    Quartz is one of the most common minerals on the surface of the earth, and is a primary rock-forming mineral across the rock cycle. These two factors make quartz an obvious target for sediment provenance studies. Observations from experimental and natural samples demonstrate that the trace element content of quartz often reflects the conditions of quartz formation. When quartz is weathered from its primary crystallization setting (i.e., quartz from a granitoid) it can retain many chemical signatures of formation throughout the sedimentation processes. These geochemical signatures can be used to understand the primary source of individual quartz grains within a sediment. Here we present a case study from the Bega River catchment to demonstrate that quartz grains in sediments at the mouth of the Bega River are sourced from granitoids within the drainage basin. Data presented here also indicate that a portion of the beach sediment is also derived from either (i) sedimentary rocks within the basin or; (ii) mixing with sediments at the mouth of the river. The Bega River catchment was selected for this study because it is both small and has a well-constrained bedrock lithology, making it an ideal location to test the utility of this provenance technique. However, quartz trace element provenance has broad applications to modern and ancient sediments and can be used in lieu of, or in conjunction with, other provenance techniques to elucidate sediment transport through time.

  16. Reduction of the impedance of a contactless conductivity detector for microchip capillary electrophoresis: compensation of the electrode impedance by addition of a series inductance from a piezoelectric quartz crystal.

    Science.gov (United States)

    Kang, Qi; Shen, Dazhong; Li, Qingling; Hu, Qiang; Dong, Jianfeng; Du, Junguo; Tang, Bo

    2008-10-15

    A low-impedance capacitively coupled contactless conductivity detector (LIC (4)D) for microchip capillary electrophoresis was reported. The LIC (4)D was the series combination of a piezoelectric quartz crystal (PQC) resonator with a capacitively coupled contactless conductivity detector (C (4)D) outside on the microchip lid. The electrode impedance in the LIC (4)D was reduced because the capacitive impedance from the wall capacitance was compensated by the inductive impedance from the PQC. The operation frequency of the LIC (4)D was set at the resonant frequency of the series combination of a PQC with a C (4)D, wherein a minimum in the total impedance was obtained. It was shown that the sensitivity of LIC (4)D was much higher than that of C (4)D itself, especially in the microchip with a thick lid. Under the experimental conditions, the signal-to-noise ratios of the LIC (4)D were improved by approximately 20-50 times over those of the C (4)D. Reproducible separations of a mixture of inorganic cations (K (+), Na (+), Li (+)) were demonstrated. After a digital filter treatment by the fast Fourier transform algorithm, the detection limits were 0.38, 0.49, and 1.6 microM for K (+) in the LI C (4)D with the microchip lid thickness of 0.20, 0.40, and 1.0 mm, respectively.

  17. Microball lens integrated fiber probe for optical frequency domain imaging

    Institute of Scientific and Technical Information of China (English)

    Jae-Ho Han; J.U.Kang

    2011-01-01

    An integrated microball lens fiber catheter probe is demonstrated, which has better lateral resolution and longer working distance than a corresponding bare fiber probe with diverging beam for Fourier domain optical coherence tomography (FDOCT). Simulation results are shown to gain the effect of the distance between the microball lens and the bare fiber to the focusing plane and beam width. The freedom of modifying the working distance and lateral resolution is shown. This is achieved by changing the gap distance between the single-mode fiber and the microball lens within the packaged surgical needle catheter without using an additional beam expander having a fixed length. The probe successfully acquired cross-sectional images of ocular tissues from an animal sample with the proposed miniaturized imaging probe.%@@ An integrated microball lens fiber catheter probe is demonstrated,which has better lateral resolution and longer working distance than a corresponding bare fiber probe with diverging beam for Fourier domain optical coherence tomography(FDOCT).Simulation results are shown to gain the effect of the distance between the microball lens and the bare fiber to the focusing plane and beam width.The freedom of modifying the working distance and lateral resolution is shown.This is achieved by changing the gap distance between the single-mode fiber and the microball lens within the packaged surgical needle catheter without using an additional beam expander having a fixed length.The probe successfully acquired crosssectional images of ocular tissues from an animal sample with the proposed miniaturized imaging probe.

  18. 40 CFR 92.110 - Weighing chamber and micro-balance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Weighing chamber and micro-balance. 92... Weighing chamber and micro-balance. (a) Ambient conditions—(1) Temperature. The temperature of the chamber.... (b) Weighing balance specifications. The microbalance used to determine the weights of all...

  19. Chemical etching of deformation sub-structures in quartz

    Science.gov (United States)

    Wegner, M. W.; Christie, J. M.

    1983-02-01

    Chemical etching of dislocations has been studied in natural and synthetic quartz single crystals, in deformed synthetic quartz and in naturally and experimentally deformed quartzites. The ability of different etchants to produce polished or preferentially etched surfaces on quartz is described. Dislocation etching was achieved on all crystal planes examined by using a saturated solution of ammonium bifluoride as the etchant. Appropriate etching times were determined for etching quartzites for grain size, subgrain boundaries, deformation lamellae, dislocations and twins. Growth and polished surfaces of synthetic single crystal quartz were similarly etched and dislocation etch pits, characteristic of various orientations were found. The use of ammonium bifluoride proved to be expecially advantageous for the basal plane, producing a polished surface with etch pits, suitable for dislocation etch pit counting. “Double” etch pits have been found on Dauphiné twin boundaries on the basal plane and the first order prism, using this etchant. Slip lines and deformation bands were suitably etched on deformed synthetic crystal surfaces for identification of the slip planes. Other acidic etchants have been explored and their application to the study of deformation structures in quartz crystals is discussed.

  20. Drinking-Straw Microbalance and Seesaw: Stability and Instability

    Science.gov (United States)

    Chapman, Peter; Glasser, Leslie

    2015-01-01

    The mechanics of a beam balance are little appreciated and seldom understood. We here consider the conditions that result in a stable balance, with center of gravity below the fulcrum (pivot point), while an unstable balance results when the center of gravity is above the fulcrum. The highly sensitive drinking-straw microbalance, which uses a…

  1. Force chain forming quartz in an ultramylonite

    Science.gov (United States)

    Kilian, Rüdiger; Morales, Luiz F. G.; Peters, Max

    2014-05-01

    Polymineralic ultramylonites often show microstructures indicative of grain size sensitive creep with dissolution precipitation or diffusion accommodated grain boundary sliding. Typically phases show an anticorrelated distribution, the grain size is small and a crystallographic preferred orientation is absent. The latter observation is usually thought to originate from rigid body rotation of grains because flow dominated by diffusion creep operates at differential stresses, which are too low to activate crystal-plastic mechanisms. Here, we present quartz texture measurements from a natural ultramylonite, deformed under upper amphibolite facies conditions from the Nordmannvik Nappe, Upper Allochton of the Norwegian Caledonides. The ultramylonite has a mean grain size crystal-plastic processes. Alternative texture forming processes (e.g. growth textures) are also discussed. The texture in the foliation parallel clusters is thought to be an inherited texture from lower strain stages in the ultramylonite, as it is mostly present in the least deformed parts of the ultramylonite. However, we suggest that the texture formed in the foliation oblique clusters is related to a dynamic formation of force chains between quartz grains, where differential stresses become high enough for plastic yielding. The presence of force chains questions whether ultramylonites necessarily need to possess a linear viscous rheology, even if microstructures would indicate a diffusion creep mechanism. Pennacchioni G., Menegon L., Leiss B., Nestola F., Bromiley G., 2010: Development of crystallographic preferred orientation and microstructure during plastic deformation of natural coarse?grained quartz veins. Journal of Geophysical Research, Vol. 115, B12405

  2. Axiomatic Design of Micro Quartz Rate Sensor

    Institute of Scientific and Technical Information of China (English)

    SHI Yang-he; ZHANG Hong-hai; LIU Sheng

    2007-01-01

    Quartz rate sensors (QRS) made out of one single piece of quartz crystal are inertial devices which can be used for general rate control, stabilization, automotive and aerospace/defense markets,etc. The mechanical design of the QRS has been investigated based on axiomatic design. The axiomatic design matrix of the mechanical structure of Coriolis Vibratory Gyroscopes (CVG) has been proposed. The mechanical function of QRS is divided into three Function Requirements ( FR ) , i. e. , FR1 is the drive mode, FR2 is the sense mode, FR3 is a coupled connection where the Coriolis force can couple the two modes with a term proportional to the rotational rate. A new QRS which is easy to be fabricated has been put forward. Furthermore, the new QRS indicated that the axiomatic design is a help to functional design of products.

  3. Diagenetic Quartz Morphologies and Zeolite formation

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari; Hansen, Rikke Weibel; Friis, Henrik

    ; the core of the zeolite crystals appears to have been more unstable than the rim and dissolved first.  Later the entire crystal dissolved and left an impression of the euhedral zeolite crystal in the microquartz coating.  Such openings in the microquartz coating are nucleation points for macroquartz.  Thus......, the precipitation of zeolite may later facilitate further quartz cementation, which might otherwise be retarded by the presence of disordered microquartz. The silica activity of pore fluids can influence zeolite precipitation.  Although zeolite formation is clearly related to volcanic ash, zeolite has also formed...... are abundant in some of associated shales; and 2) volcanic ash. The dissolution of biogenic silica may result in a rapid release of silica thereby promoting the formation of diagenetic opal/microquartz, but there may be a limited release of Al. A limited release of Al may result in precipitation of Si...

  4. Identification of color development potential of quartz by Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Alkmim, Danielle G.; Lameiras, Fernando S.; Almeida, Frederico O.T., E-mail: alkmia@yahoo.com.br, E-mail: fsl@cdtn.br [Centro e Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horionte, MG (Brazil)

    2013-07-01

    Colorless quartz is usually exposed to ionizing radiation (gamma rays or high energy electron beams) to acquire different colors for jewelry. Color development is due to the presence of traces of some elements such as aluminum, iron, hydrogen, lithium, or sodium. Most quartz crystals are extracted colorless from nature and it is necessary to separate those that can develop colors from those that cannot. Irradiation tests can be used to accomplish this separation, but they take a long time. Infrared signature of colorless quartz can also be used. However, infrared spectroscopy is quite expensive, especially when using portable devices. Raman spectroscopy is now available as an inexpensive and portable technique that could provide identification of the samples of colorless quartz still in the field, facilitating the prediction for their economic exploitation. In addition, Raman spectroscopy usually requires a minimum or no sample preparation. This paper presents an investigation of the feasibility of using Raman spectroscopy as a substitute for infrared spectroscopy to predict the potential for color development of quartz. A band at 3595 cm{sup -1} in the Raman shift spectrum was observed only along the c axis of a prasiolite excited by a high power 514 nm laser. This band was not observed in quartz samples that do not develop color after irradiation. Further studies are required to identify the potential for color development by Raman spectroscopy of other types of colorless quartz. (author)

  5. The microball and Gammasphere: Research highlights and future directions

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, M.; Sarantites, D.G.; LaFosse, D.R.; Lerma, F. [Washington Univ., Saint Louis, MO (United States)

    1996-12-31

    The Microball, a compact, 4{pi} charged-particle detector array, has been used in conjunction with Gammasphere for numerous physics experiments, and more are planned in the near future. A summary of this research program is presented, and the device and its capabilities are described. An example of its use in the study of the population and entry state excitation energy distributions of normal and superdeformed bands in {sup 82}Sr is presented.

  6. Analysis of Rare Earth Elements (REE) in vein quartz and quartz-sandstone host rock in the Zhelannoe high purity quartz deposit, Russia

    Science.gov (United States)

    Zemskova, Marina; Prokofiev, Vsevolod; Bychkov, Andrey

    2015-04-01

    The Zhelannoe high purity quartz deposit is located on the western slope of the Polar Urals. It is one of the largest deposits of vein quartz and rock crystal in Russia. Most of the mineralization is hosted within a single horizon of very firm quartz-sandstone, where plastic deformation did not occur almost entirely. All tectonic stress was released by the development of numerous thrust faults of different scales. Cavities formed during this process were later filled with quartz and rock crystal. In order to obtain more details on conditions under which mineralization took place, analysis of trace element contents in vein quartz and host rocks, and the micro-thermometric study of fluid inclusions in quartz have been carried out. The trace element composition of vein quartz and of the host rock has been determined by ICP-MS. The results have shown that concentrations of most of the 46 studied elements in quartz are two orders of magnitude lower than in chondrite, and more than three orders of magnitude lower than in the upper crust. Even though Pb and Li have the highest concentrations in quartz samples, levels are only nearly comparable in chondrite, and substantially lower in the upper crust. At the same time, negative anomalies of Pb and Li concentrations in the host rock may indicate the removal of these elements during vein quartz formation. Contents of most REEs are two orders of magnitude lower than in chondrite, and three orders of magnitude lower than in the host rock. Generally, the patterns of REE distribution in vein quartz and the host rock express a clear correlation; confirming the genetic link between vein quartz and quartz-sandstone host rock. However, the process of quartz recrystallization led to an intense decrease of REEs content, and of all other impurities, which consequently influenced industrial value of the Zhelannoe deposit. As a result of the micro-thermometric study of fluid inclusions in quartz, the following physical

  7. Quartz resonator processing system

    Science.gov (United States)

    Peters, Roswell D. M.

    1983-01-01

    Disclosed is a single chamber ultra-high vacuum processing system for the oduction of hermetically sealed quartz resonators wherein electrode metallization and sealing are carried out along with cleaning and bake-out without any air exposure between the processing steps. The system includes a common vacuum chamber in which is located a rotatable wheel-like member which is adapted to move a plurality of individual component sets of a flat pack resonator unit past discretely located processing stations in said chamber whereupon electrode deposition takes place followed by the placement of ceramic covers over a frame containing a resonator element and then to a sealing stage where a pair of hydraulic rams including heating elements effect a metallized bonding of the covers to the frame.

  8. Rotational Symmetry and Absolute Sign of Second-Order Susceptibility of α-Quartz

    Institute of Scientific and Technical Information of China (English)

    吕荣; 王鸿飞

    2003-01-01

    We investigate the rotational symmetry and absolute sign of the effective second-order susceptibility of the righthanded z-cut α-quartz crystal in different crystal orientations through the second-harmonic-generation phase interference between standard and reference of thin α-quartz plates. The Ds rotational symmetry of the z-cut α-quartz crystal shows 6 alternating sign sections of the second-order susceptibility in the 360° rotation, which leads to two distinctive interference patterns between the reference and standard second harmonic field. From this information, the sign of the interference pattern in the second harmonic phase measurement could be readily derived.

  9. Quartz resonator instabilities under cryogenic conditions.

    Science.gov (United States)

    Goryachev, Maxim; Galliou, Serge; Abbe, Philippe; Bourgeois, Pierre-Yves; Grop, Serge; Dubois, Benoit

    2012-01-01

    The phase noise of a quartz crystal resonator working at liquid helium temperatures is studied. Measurement methods and the device environment are explained. The phase noise is measured for different resonance modes, excitation levels, amount of operating time, device orientations in relation to the cryocooler vibration axis, and temperatures. Stability limits of a frequency source based on such devices are evaluated in the present measurement conditions. The sources of phase flicker and white noises are identified. Finally, the results are compared with previous works.

  10. Invention of temperature-insensitive quartz oscillation plate enabling highly stable communications and clocks: Review of Issac Koga's works

    Science.gov (United States)

    Iga, Kenichi

    2016-10-01

    This is a review article on a stable quartz oscillator. In April 1933, Issac Koga of Tokyo Institute of Technology reported R1 cut quartz crystal plates having a zero temperature coefficient of frequency. This invention was used at first for radio transmitters and later on for clocks. Today, this type of temperature-insensitive quartz crystal oscillator has proven indispensable to all radio communication systems and much of information electronics.

  11. Electrochemical quartz crystal microbalance study on Au-supported Pt adlayers for electrocatalytic oxidation of methanol in alkaline solution%电化学石英晶体微天平研究碱性介质中单层级铂原子修饰的金电极上甲醇的电催化氧化

    Institute of Scientific and Technical Information of China (English)

    黄钊; 贾学恩; 谢青季; 谭月明; 黄素清; 黄金花; 孟越; 姚守拙

    2010-01-01

    通过在Au电极表面欠电位沉积(UPD)Cu、再与Pt 源(H2PtCl6或K2PtCl4)进行置换反应,制得单层级Pt原子修饰的金电极(对H2PtCl6或K2PtCl4,所制电极分别记为(CuUPD-Pt(4+)n/AU或Pt(CuUPD-Pt(2+)n)/AU,n表示欠电位沉积一置换过程的重复次数).用电化学石英晶体微天平((EQCM)技术定量研究了所制电极,评估了其在碱性环境中催化甲醇氧化的质量比活性((SECA).结果表明,以H2PtCl.为Pt源所制电极Pt(CuUPD-Pt(4+)s)/Au)的活性更高,最大SECA高达35.7 mAμg '.根据EQCM结果计算了置换效率,籍此讨论了Pt原子在Au电极表面的层层组装结构,发现所制电极表面的裸Au位点分布百分数与实验结果(由Au0x还原峰电量测算)吻合.我们认为,EQCM技术是一种定量研究电极支撑的超薄催化剂的有效手段,这种高效的单层级贵金属催化剂有望在生物、能源、环境相关的电催化研究中进一步应用.

  12. 消散石英晶体微天平对木瓜蛋白酶水解唾液膜的动力学研究%Kinetic Study of Papain Hydrolysis of Salivary Film by the Quartz Crystal Microbalance with Dissipation.

    Institute of Scientific and Technical Information of China (English)

    李水根; 林志明; 姚江武

    2011-01-01

    Objective: To investigate the dynamics of papain hydrolysis at various of pH values, ionic strengths,and temperatures when using the human whole saliva as a model films.Methods: QCM-D technique was used to observe the changes in frequency of salivary films in enzymatic hydrolysis at various conditions.Results: The WS film was partially removed after treated by enzyme at various conditions.The character of the interactions of papain with salivary proteins was sensitive to various conditions i.e.pH value, ionic strength, and temperature which should be considered during the choice and application of enzyme source.In general, with decreasing pH value and increasing ionic strength (from I to 5 mM) and temperature, catalytic rate of papain significantly increased.Conclusion: Enzymatic kinetics show that the process of papain hydrolysis of WS film was pH-, ionic strength- and temperature-dependent.This behavior of papain can be used in the formulation of toothpaste, mouthrinse and denture cleanser and helps to achieve the desired antimicrobial compounds.The optimization of enzymes will require a more detailed understanding of regulative system and multiple factors generated in the processes.%目的:本实验以人全唾作为唾液获得性膜的体外实验模型,研究不同pH值、离子强度和温度条件下木瓜蛋白酶水解的动力学.方法:通过消散石英晶体微天平在各种条件下观察酶水解唾液膜的频率变化.结果:在各种条件下唾液膜被木瓜蛋白酶部分水解.木瓜蛋白酶与唾液蛋白质的相互作用对pH值、离子强度和温度的改变敏感.在选择和应用酶时,该特性应加以考虑.降低pH值,提高离子强度(1~5 mmol/L范围内)和温度,木瓜蛋白酶的催化效率增强.结论:酶动力学显示木瓜蛋白酶水解唾液膜的过程具有pH值、离子强度和温度的依赖性特点.在牙膏、漱口水、义齿清洁剂的配方中利用木瓜蛋白酶的这一特点,有助于获得理想的抗菌复合剂.酶的最佳化尚需更进一步理解反应过程中的调节机制和多重的影响因素.

  13. Crystal growth of pure and impurity-doped lead chloride single crystals from the melt

    NARCIS (Netherlands)

    Willemsen, B.

    An account is given of the purification and the crystal growing of lead chloride. Difficulties observed are blackening of the material and the formation of oxides. It is evident that oxygen should be avoided. The influence of water vapour is studied with mass spectroscopy, crystal microbalance

  14. Crystal growth of pure and impurity-doped lead chloride single crystals from the melt

    NARCIS (Netherlands)

    Willemsen, B.

    1971-01-01

    An account is given of the purification and the crystal growing of lead chloride. Difficulties observed are blackening of the material and the formation of oxides. It is evident that oxygen should be avoided. The influence of water vapour is studied with mass spectroscopy, crystal microbalance measu

  15. Hexagonal quartz resonator

    Science.gov (United States)

    Peters, Roswell D. M.

    1982-01-01

    A generally flat, relatively thin AT-cut piezoelectric resonator element structured to minimize the force-frequency effect when mounted and energized in a housing. The resonator is in the form of an equilateral hexagon with the X crystallographic axis of the crystal passing through one set of opposing corners with mounting being effected at an adjacent set of corners respectively .+-.60.degree. away from the X axis which thereby results in a substantially zero frequency shift of the operating frequency.

  16. Chiral habit selection on nanostructured epitaxial quartz films.

    Science.gov (United States)

    Carretero-Genevrier, Adrián; Gich, Martí; Picas, Laura; Sanchez, Clément; Rodriguez-Carvajal, Juan

    2015-01-01

    Understanding the crystallization of enantiomorphically pure systems can be relevant to diverse fields such as the study of the origins of life or the purification of racemates. Here we report on polycrystalline epitaxial thin films of quartz on Si substrates displaying two distinct types of chiral habits that never coexist in the same film. We combine Atomic Force Microscopy (AFM) analysis and computer-assisted crystallographic calculations to make a detailed study of these habits of quartz. By estimating the surface energies of the observed crystallites we argue that the films are enantiomorphically pure and we briefly outline a possible mechanism to explain the habit and chiral selection in this system.

  17. Deformations of crystal frameworks

    CERN Document Server

    Borcea, Ciprian S

    2011-01-01

    We apply our deformation theory of periodic bar-and-joint frameworks to tetrahedral crystal structures. The deformation space is investigated in detail for frameworks modelled on quartz, cristobalite and tridymite.

  18. Amorphization of α-Quartz under Irradiation

    Science.gov (United States)

    Douillard, L.; Duraud, J. P.

    1996-12-01

    The course of radiation induced damage produced in α-quartz by neutrons, ions, electrons or photons — commonly known as metamictization — has been re-analyzed by careful comparison of available experimental data. Specific interest was devoted to confront experimental metamict state features with current structural models. It comes out that the metamict state of irradiated quartz should exhibit some structural characteristics of the modulated structure proposed for vitreous silica. The metamictization process is consistent with a structural relaxation process of a highly defective quartz matrix. According to this new point defect analysis, structural relaxation should be triggered by a critical concentration of oxygen vacancy point defects likely to significantly lower the connectivity of the SiO{2} network. Various experimental results are interpreted by incorporating the influence of the SiO{2} crystalline polymorph and the influence of the nature of the irradiating particle to the point defect model. Nous avons étudié les modifications de propriétés et de structures de monocristaux de quartz α, consécutives à une irradiation sévère par des neutrons, des ions, des électrons ou des photons. Ce phénomène d'altération du quartz sous irradiation porte le nom de métamictisation. Notre travail exploite les recoupements de travaux antérieurs. Une attention particulière a été portée à la confrontation entre les données structurales expérimentales disponibles sur l'état métamicte du quartz et les modèles structuraux proposés. L'état métamicte du quartz présente ainsi les caractéristiques structurales du modèle de structure modulée, avancé pour décrire la structure de la silice thermique. Le mécanisme de métamictisation procéderait par relaxation de la matrice cristalline fortement endommagée. Ce phénomène de relaxation serait initié par l'apparition de concentration critique de défauts ponctuels de type lacunes d

  19. Corrosion protection of copper by polypyrrole film studied by electrochemical impedance spectroscopy and the electrochemical quartz microbalance

    Science.gov (United States)

    Lei, Yanhua; Ohtsuka, Toshiaki; Sheng, Nan

    2015-12-01

    Polypyrrole (PPy) films were synthesized on copper in solution of sodium di-hydrogen phosphate and phytate for corrosion protection. The protection properties of PPy films were comparatively investigated in NaCl solution. During two months immersion, the PPy film doped with phytate anions, working as a cationic perm-selective membrane, inhibited the dissolution of copper to 1% of bare copper. Differently, the PPy film doped with di-hydrogen phosphate anions, possessing anionic perm-selectivity, was gradually reduced, and inhibited the dissolution to 7.8% of bare copper. Degradation of the PPy films was studied by comparing the electrochemical impedance spectroscopy change at different immersion time and Raman spectra change after immersion.

  20. 松辽盆地南部HX井上白垩统青山口组黑色泥岩的矿物组成与自生微晶石英成因%Mineral Composition and Origin of Authigenic Quartz Crystals in Black Mudstone, in well HX, Qingshankou Formation, Upper Cretaceous, Songliao Basin

    Institute of Scientific and Technical Information of China (English)

    刘立; 王力娟; 杨永智; 于志超

    2012-01-01

    The mineral composition and diagenesis of shale play important roles in constraining the sealing efficiency as caprock of CO2 sequestration and the fracability in shale gas. X-ray fluorescence spectrum, X-ray diffraction and scanning electron microscopy are employed in the determination of mineral composition of mudstone and the identification of submicron-sized authigenic quartz crystals in well HX, Qingshankou Formation, Upper Cretaceous. The type of host rock and weathering effect are in consistent with mudstone in Qingshankou Formation. The mudstone is composed of clay mineral, albite, quartz and less K-feldspar. The clay fraction consists mainly of mixed-layer I/S and minor amounts of chlorite. Brittle mineral (albite, quartz and feldspar) average content is 44. 43%, and clay mineral content is 54. 26% on average. Submicron-sized authigenic quartz crystals released from S - I relation occur as large amounts of extremely fine-grained micro-sized crystals embedded as discrete,small clusters/nest and locate in micropores in mixed-layer I/S. The caprock consisting of mainly mixed-layer I/S mineral and minor amount of micron-quartz will be conductive to long-term CO2 geological storage. The content of brittle mineral meet the reservoir standard of industrial value shale gas, while the content of clay mineral is quite low.%泥质岩的矿物组成和成岩作用是制约其作为CO2地质封存的盖层封闭能力和作为页岩气储层具易压裂性质的重要原因.通过地球化学分析、X-射线衍射分析和扫描电镜观测及能谱测定,确定了松辽盆地南部HX井上白垩统青山口组泥岩的矿物组成.识别出了蒙皂石转变伊利石反应过程中形成的亚微米级自生微晶石英.研究表明:HX井上白垩统青山口组泥岩的母岩岩石类型和风化效应一致,泥岩主要由黏土矿物、钠长石和石英组成,钾长石少量;黏土矿物以伊利石/蒙皂石混层为主,其次为绿泥石;脆性矿物(钠

  1. Manufacturing technology for high quality swept-culture growth quartz

    Science.gov (United States)

    Balascio, J. F.; Lias, N. C.

    1983-09-01

    Relatively low impurity alpha-quartz has been grown from the hydroxide mineralizer system with the use of three types of nutrient: converted, special cultured and cultured. The converted nutrient resulted in the lowest total ppm level (2.6) and Al ppm level (0.5) in the as-grown crystals. Special cultured and cultured nutrients resulted in 1.7 ppm and 2.1 ppm of aluminum in crystals grown, respectively, from these nutrients. Infrared Q values ranged from 2.5x10 to the 6th power in these crystals. With respect to rho in the as-grown crystals, a ten minute etching of seeds in 7.0 molal ammonium bifluoride has resulted in the growth of the lowest etch channel density crystals (approx = 135/sq cm).

  2. Synkinematic quartz cementation in partially open fractures in sandstones

    Science.gov (United States)

    Ukar, Estibalitz; Laubach, Stephen E.; Fall, Andras; Eichhubl, Peter

    2014-05-01

    have recorded opening histories that lasted several tens of millions of years. Quartz bridges will form when the increase in fracture aperture is small for single fracture events, the rate of precipitation is greater than the rate of fracture aperture, and fresh non-euhedral nucleation surfaces continue to be created by fracturing. Because of the vast difference in growth rates between the c-axis (fast) and the a-axis (slow) of quartz crystals, the crystallographic orientation of quartz may play a role on the morphology and size of such bridges, and therefore degree of cement infill in fractures. SEM-based backscattered electron diffraction (EBSD) was used to explore the effect of the crystallographic orientation of quartz on the growth of quartz bridges in fractures from the Jurassic-Cretaceous Nikanassin Formation, northwestern Alberta Foothills, the Travis Peak Formation, East Texas, and the Cretaceous Mesaverde Group, Piceance Basin, Colorado. We find that, in all samples, most c-axes are oblique rather than perpendicular to the fracture wall, and well-developed bridges that are oriented at a low angle to the fracture wall are widespread. We conclude that precipitation on anhedral (fractured) surfaces exerts a larger control on the growth of quartz bridges than the orientation of the crystallographic c-axis.

  3. Electromodulated absorption in smoky quartz

    NARCIS (Netherlands)

    Brom, W.E. van den; Volger, J.

    1974-01-01

    The optical absorption coefficient of “smoky” quartz (containing aluminium) can be modulated by applying an electric field. The effect saturates at high fields and low temperatures and reaches a maximum at 535 nm. The results are discussed in terms of a model consisting of a colour centre, dipolar i

  4. Laser welding of fused quartz

    Science.gov (United States)

    Piltch, Martin S.; Carpenter, Robert W.; Archer, III, McIlwaine

    2003-06-10

    Refractory materials, such as fused quartz plates and rods are welded using a heat source, such as a high power continuous wave carbon dioxide laser. The radiation is optimized through a process of varying the power, the focus, and the feed rates of the laser such that full penetration welds may be accomplished. The process of optimization varies the characteristic wavelengths of the laser until the radiation is almost completely absorbed by the refractory material, thereby leading to a very rapid heating of the material to the melting point. This optimization naturally occurs when a carbon dioxide laser is used to weld quartz. As such this method of quartz welding creates a minimum sized heat-affected zone. Furthermore, the welding apparatus and process requires a ventilation system to carry away the silicon oxides that are produced during the welding process to avoid the deposition of the silicon oxides on the surface of the quartz plates or the contamination of the welds with the silicon oxides.

  5. Highly crystallized nanometer-sized zeolite a with large Cs adsorption capability for the decontamination of water.

    Science.gov (United States)

    Torad, Nagy L; Naito, Masanobu; Tatami, Junichi; Endo, Akira; Leo, Sin-Yen; Ishihara, Shinsuke; Wu, Kevin C-W; Wakihara, Toru; Yamauchi, Yusuke

    2014-03-01

    Nanometer-sized zeolite A with a large cesium (Cs) uptake capability is prepared through a simple post-milling recrystallization method. This method is suitable for producing nanometer-sized zeolite in large scale, as additional organic compounds are not needed to control zeolite nucleation and crystal growth. Herein, we perform a quartz crystal microbalance (QCM) study to evaluate the uptake ability of Cs ions by zeolite, to the best of our knowledge, for the first time. In comparison to micrometer-sized zeolite A, nanometer-sized zeolite A can rapidly accommodate a larger amount of Cs ions into the zeolite crystal structure, owing to its high external surface area. Nanometer-sized zeolite is a promising candidate for the removal of radioactive Cs ions from polluted water. Our QCM study on Cs adsorption uptake behavior provides the information of adsorption kinetics (e.g., adsorption amounts and rates). This technique is applicable to other zeolites, which will be highly valuable for further consideration of radioactive Cs removal in the future.

  6. An asymmetric resonant coupling wireless power transmission link for Micro-Ball Endoscopy.

    Science.gov (United States)

    Sun, Tianjia; Xie, Xiang; Li, Guolin; Gu, Yingke; Deng, Yangdong; Wang, Ziqiang; Wang, Zhihua

    2010-01-01

    This paper investigates the design and optimization of a wireless power transmission link targeting Micro-Ball Endoscopy applications. A novel asymmetric resonant coupling structure is proposed to deliver power to an endoscopic Micro-Ball system for image read-out after it is excreted. Such a technology enables many key medical applications with stringent requirements for small system volume and high power delivery efficiency. A prototyping power transmission sub-system of the Micro-Ball system was implemented. It consists of primary coil, middle resonant coil, and cube-like full-direction secondary receiving coils. Our experimental results proved that 200mW of power can be successfully delivered. Such a wireless power transmission capability could satisfy the requirements of the Micro-Ball based endoscopy application. The transmission efficiency is in the range of 41% (worst working condition) to 53% (best working condition). Comparing to conventional structures, Asymmetric Resonant Coupling Structure improves power efficiency by 13%.

  7. Micro-Ball Lens Array Fabrication in Photoresist Using Ptfe Hydrophobic Effect

    CERN Document Server

    Shyu Ruey Fang; Tsai Wen Ren; Tsai Jhy Cherng

    2007-01-01

    This paper presents a simple method to fabricate micro-ball lens and its array. The key technology is to use the hydrophobic characteristics of polyterafluoroethylene (PTFE) substrate. High contact angle between melted photoresist pattern and PTFE can generate micro-ball lens and its array. PTFE thin film was spun onto a silicon wafer and dried in oven. Photoresist AZ4620 was used to pattern micro-columns with different diameters 60, 70 and 80 $\\mu$m. A thermal reflow process then was applied to melt these micro-column patterns resulted in micro-ball lens array. The achieved micro-ball lens array with diameter 98 $\\mu$m was fabricated using 80 $\\mu$m in diameter patterns. This method provides a simple fabrication process and low material cost.

  8. Radioluminescence of synthetic quartz related to alkali ions

    Energy Technology Data Exchange (ETDEWEB)

    Martini, M., E-mail: m.martini@unimib.it [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); INFN-Sezione di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Fasoli, M. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Galli, A. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Istituto di Fotonica e Nanostrutture, IFN-CNR (Italy); Villa, I. [Dipartimento di Scienza dei Materiali, Universita degli Studi di Milano Bicocca, Via Cozzi 53, I-20125 Milano (Italy); Guibert, P. [IRAMAT-CRP2A (Institut de recherche sur les Archeomateriaux), UMR no. 5060, CNRS-Universite Bordeaux III, F-33607 Pessac (France)

    2012-04-15

    The radioluminescence (RL) of synthetic quartzes (GEMMA Quartz and Crystal Company) has been measured at room temperature. Some samples were treated by electrodiffusion ('sweeping') in order to change the concentrations of alkali ions, mainly Li{sup +} and Na{sup +}, which in quartz are known to be linked to Al ions, substitutional for Si ions. The RL emission spectra show evidence of a role of alkali ions in affecting some specific emissions. All the spectra could be analysed as composed of four bands in the blue and UV region. Specifically, the well known blue emission at around 470 nm was seen to be composed by two bands at 430 nm (2.86 eV) and at 485 nm (2.53 eV). Effects of irradiation, during the RL measurements, were clearly seen only in the 'Li swept in' sample, namely an increase in the 485 nm band intensity and a decrease in the 430 nm band one. The previously reported UV emission was detected at 355 nm (3.44 eV) in all the samples, being the most intense band in the 'swept out' sample. A further UV emission was detected at 315 nm (3.94 eV), more intense in untreated samples. Possible assignments of the detected emission bands are discussed in relation to the defects of quartz, specifically focusing on the Al centres that are most affected by sweeping procedures. - Highlights: Black-Right-Pointing-Pointer Contribution to the understanding of relationships between defects in quartz and luminescence emissions. Black-Right-Pointing-Pointer Role of charge compensators at substitutional Al sites in the optical properties of quartz. Black-Right-Pointing-Pointer Evidence of the double nature of the 'blue emission' (around 470 nm).

  9. Influence of H2O Rich Fluid Inclusions on Quartz Deformation

    Science.gov (United States)

    Thust, Anja; Heilbronner, Renée.; Stünitz, Holger; Tarantola, Alexandre; Behrens, Harald

    2010-05-01

    The effect of H2O on the strength of quartz is well known and has been discussed many times in the literature (e.g. Griggs & Blacic 1965, Kronenberg 1994). In this project we study the H2O interactions between natural dry quartz and H2O rich fluid inclusions during deformation in the solid medium Griggs apparatus. High pressure and temperature experiments were carried out using a quartz single crystal containing a large number of H2O-rich fluid inclusions. Adjacent to the fluid inclusions the crystal is essentially dry (Kronenberg A.K., (1994): Hydrogen specifications and chemical weakening of quartz, Rev. Mineral. Ser. 29 (1994), pp. 123-176.

  10. Dew point fast measurement in organic vapor mixtures using quartz resonant sensor

    Science.gov (United States)

    Nie, Jing; Liu, Jia; Meng, Xiaofeng

    2017-01-01

    A fast dew point sensor has been developed for organic vapor mixtures by using the quartz crystal with sensitive circuits. The sensor consists of the quartz crystal and a cooler device. Proactive approach is taken to produce condensation on the surface of the quartz crystal, and it will lead to a change in electrical features of the quartz crystal. The cessation of oscillation was measured because this phenomenon is caused by dew condensation. Such a phenomenon can be used to detect the dew point. This method exploits the high sensitivity of the quartz crystal but without frequency measurement and also retains the stability of the resonant circuit. It is strongly anti-interfered. Its performance was evaluated with acetone-methanol mixtures under different pressures. The results were compared with the dew points predicted from the universal quasi-chemical equation to evaluate the performance of the proposed sensor. Though the maximum deviations of the sensor are less than 1.1 °C, it still has a fast response time with a recovery time of less than 10 s, providing an excellent dehumidifying performance.

  11. Evidence for warmer event from quartz grains in the soil of Grove Mountains, East Antarctica

    Institute of Scientific and Technical Information of China (English)

    Yan Xin; Li Xiaoli; Liu Xiaohan; Zhang Ru-fan

    2005-01-01

    The cold desert soil has been discovered at first time in southern ridgeof Mount Harding, Grove Mountains of interior East Antarctica Ice Sheet. Based on the micro structural observation, dominant characteristics of quartz grains include: distinct surface stria and fractures, and clean features of frost action at both of crystal margins and micro crannies of quartz grains. These features show a pedogenesis environment of few water, short transportation and frost action, revealing a warmer climatic event existed in this region.

  12. Shock metamorphism of deformed quartz

    Science.gov (United States)

    Gratz, Andrew J.; Christie, John; Tyburczy, James; Ahrens, Thomas; Pongratz, Peter

    1988-01-01

    The effect produced by shock loading (to peak pressures of 12 and 24) on deformed synthetic quartz containing a dislocation and abundant bubbles and small inclusions was investigated, and the relationships between preexisting dislocation density shock lamellae in the target material were examined. The resultant material was found to be inhomogeneously deformed and extremely fractured. Results of TEM examinations indicate that no change in dislocation density was caused by shock loading except in regions containing shock lamellae, where the dislocation density was lowered. The shock-induced defects tend to nucleate on and be controlled by preexisting stress concentrators; shock lamellae, glassy veins, and most curviplanar defects form in tension, presumably during release. An extremely mobile silica fluid is formed and injected into fractures during release, which forcibly removes crystalline fragments from vein walls. It is concluded that shock deformation in quartz is dominated by fracture and melting.

  13. Electric field cancellation on quartz: a Rb adsorbate induced negative electron affinity surface

    CERN Document Server

    Sedlacek, J A; Rittenhouse, S T; Weck, P F; Sadeghpour, H R; Shaffer, J P

    2015-01-01

    We investigate the (0001) surface of single crystal quartz with a submonolayer of Rb adsorbates. Using Rydberg atom electromagnetically induced transparency, we investigate the electric fields resulting from Rb adsorbed on the quartz surface, and measure the activation energy of the Rb adsorbates. We show that the adsorbed Rb induces a negative electron affinity (NEA) on the quartz surface. The NEA surface allows low energy electrons to bind to the surface and cancel the electric field from the Rb adsorbates. Our results are important for integrating Rydberg atoms into hybrid quantum systems and the fundamental study of atom-surface interactions, as well as applications for electrons bound to a 2D surface.

  14. Chirality of quartz. Fibrosis and tumour development in dust inoculated mice.

    Science.gov (United States)

    Ebbesen, P

    1991-10-01

    Dextro (d) and laevo (l) forms of quartz dust was inoculated intranasally and subcutaneously into 2-month-old (C57 x BALB/c)F1 mice which were killed 18 months later. Both d and l quartz caused fibrosis, liver nodule formation and an enhanced incidence of lymphoma/leukemia. However, the tumour incidence was significantly higher in l than in d quartz dust-treated animals. It is concluded that in addition to effects clearly independent of chirality there is evidence that the biological response to nonidentical mirror images of solid crystals may differ.

  15. Luminescence sensitivity changes in quartz

    CERN Document Server

    Wintle, A G

    1999-01-01

    In the luminescence dating of sedimentary or heated quartz, some heat treatment is usually applied to the sample immediately prior to the measurement of the optically stimulated luminescence. In this paper we report experiments on a 30,000-year-old sedimentary quartz, in which we use the luminescence response to a test dose to monitor the changes in sensitivity that are caused by holding the quartz at temperatures from 160 to 280 deg. C for times from 10 s to 22 h. For an optically bleached sample, the monitoring is by both optically stimulated luminescence and the 110 deg. C TL peak; both luminescence signals are shown to have the same sensitisation (i.e. activation energy) characteristics. For natural or laboratory irradiated samples only the 110 deg. C TL peak can be used; sensitivity increases of up to a factor of 1.3 and 3 are observed for the natural and laboratory irradiated aliquots, respectively. Up to four exponential components are used to deconvolve the sensitivity change data; the dominant compon...

  16. Oxygen isotope equilibration systematics between quartz and water

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, A. (Hebrew Univ., Jerusalem, Israel); Beckinsale, R.D.

    1979-01-01

    The /sup 18/O//sup 16/O fractionation accompanying the hydrothermal crystallization of quartz from silicic acid at 265/sup 0/ to 465/sup 0/C has been studied in order to assess the influences of (a) rate of quartz formation, (b) the nature of the reaction mechanism, and (c) temperature. At 360/sup 0/ and 465/sup 0/C, there are no indications of rate effects influencing isotope partitioning, but at 265/sup 0/C (where fractionation factors show an unusally large scatter) the evidence is inconclusive in this respect. All reaction appears to occur through solution-precipitation processes, with the intermediate phases, cristobalite and silica K, giving identical fractionation factors (within experimental errors) to quartz samples formed at the same temperature. The temperature-dependence of fractionation in the range 265/sup 0/ to 465/sup 0/C is given by the equation 10/sup 3/ ln ..cap alpha..(SiO/sub 2/--H/sub 2/O) = 3.05 x 10/sup 6/T/sup -2/ - 2.09. The data are in good agreement with other experimental calibrations of the quartz-water fractionation.

  17. Orientation of Planar Deformation Features (PDFs) in quartz

    Science.gov (United States)

    Langenhorst, F.; Deutsch, A.

    1993-01-01

    Differently oriented single crystal quartz was shocked experimentally at pressures of 20 to 32 GPa and pre-shock temperatures up to 630 C. Based on this systematic investigation, we can demonstrate that the orientation of planar deformation features in quartz is not only dependent on shock pressure but also on pre-shock temperature and shock direction. Moreover, the orientation of Planar Deformation Features (PDF's) is strongly influenced by the set-up in recovery experiments. PDF's in quartz are defined as optically recognizable, planar microstructures diagnostically produced by shock compression. PDF's differ from all kinds of microstructures found in volcanic environment and therefore, their presence is a primary criterion for recognizing impact craters and ejecta layers such as the K/T boundary. Because experiments have shown a pressure dependence of the orientation of PDF's, this property is used extensively for shock wave barometry in natural impact sites. However, the unreflected application of experimental results neglects that parameters such as pre-shock temperature, shock direction, or the experimental arrangement may influence the spatial distribution of PDF's. In order to test this assumption, shock experiments on single crystal quartz at pre-shock temperatures of 20, 275, 540, and 630 C, and with shock directions (1010) and (0001) were performed. Most of the recovery experiments were carried out by using a reverberation technique, whereas in only one experiment a single shock was produced (impedance method). In the former case 0.5 mm thin discs of single crystal quartz were used, in the latter a 15 mm thick cylinder. The orientation of PDF's was measured by means of a conventional universal stage and the results are given. Effects of the experimentation technique can be derived showing the orientation of PDF's in quartz shocked at 27.5 GPa. In comparison to the well defined peaks at (1012) found in samples from reverberation experiments, the impedance

  18. Control of Polishing Machine of Crystal Blank which Used Network Analyzer

    Science.gov (United States)

    Wakamoto, Satoru; Nakazawa, Mitsuo

    Quartz crystal devices have become an essential factor in electronic equipment such as mobile communication equipment or PC. As prices of electronic equipment have lowered, the cost-down of quartz crystal devices has been strongly demanded. To achieve the cost-down of quartz crystal device manufacturing, which uses a complex manufacturing process, the yield of the quartz crystal blank lapping process, which is the preliminary process of the quartz crystal device manufacturing process, must be increased. By introducing the network analyzer to the quartz crystal blank lapping process, we have obtained real time lapping characteristics. By obtaining the new process characteristics in real-time and visualizing them when changing lapping conditions, the network analyzer can now optimize the conditions of the process. In addition, the network analyzer can now measure the optical quartz crystal blank polishing process, which was difficult to measure by using a conventional controller.

  19. Complex fragmentation and silicification structures in fault zones: quartz mineralization and repeated fragmentation along the Fountain Range Fault (Mt. Isa Inlier, Australia)

    Science.gov (United States)

    Seybold, Lina; Blenkinsop, Tom; Heuss, Soraya; Ord, Alison; Kruhl, Jörn H.

    2015-04-01

    In large-scale fault zones fracture networks are commonly generated by high volumes of pressurized fluids, followed by quartz precipitation. In this way large amounts of quartz are formed as microcrystalline masses and as complex vein systems, with partly highly different textures, as a result of different formation processes. Based on field and microstructural data and the quantification of vein patterns, the spatial and temporal connection between fragmentation, quartz crystallization and fluid and material flow along the Fountain Range Fault at Fountain Springs was investigated. Dextral strike-slip led to up to 25 km horizontal displacement along the fault. Due to various fragmentation and quartz formation processes, a ca. 100 m high, 80 - 100 m wide and km-long quartz ridge with numerous vein systems and variable microfabrics was formed. Locally, lenses of highly altered metamorphic wall-rocks occur in the quartz zone. Where exposed, the contact to wall rocks is sharp. Millimetre- to decimetre-thick quartz veins penetrate the wall-rocks only within metre distance from the contact. Several clearly distinguishable fine-grained reddish, brownish to dark and pigment-rich quartz masses form up to 50 m wide and up to several 100 m long steep lenses that build the major part of the silicified fault zone. A chronology can be established. Some of these lenses are oriented slightly oblique to the general trend of the quartz zone, in agreement with the supposed dextral strike slip along the fault. Numerous generations of typically µm-cm thick quartz veins transect the microcrystalline quartz masses and, locally, form anisotropic networks. In the quartz masses, angular fragments often composed of quartz with, again, internal fragmentation structures, indicate earlier fracturing and silicification events. Within the veins, quartz forms geodes, locally filled with fine-grained reddish quartz and palisade structures with feathery textures and fluid-inclusion zoning

  20. Magma reservoir dynamics at Toba caldera, Indonesia, recorded by oxygen isotope zoning in quartz

    Science.gov (United States)

    Budd, David A.; Troll, Valentin R.; Deegan, Frances M.; Jolis, Ester M.; Smith, Victoria C.; Whitehouse, Martin J.; Harris, Chris; Freda, Carmela; Hilton, David R.; Halldórsson, Sæmundur A.; Bindeman, Ilya N.

    2017-01-01

    Quartz is a common phase in high-silica igneous rocks and is resistant to post-eruptive alteration, thus offering a reliable record of magmatic processes in silicic magma systems. Here we employ the 75 ka Toba super-eruption as a case study to show that quartz can resolve late-stage temporal changes in magmatic δ18O values. Overall, Toba quartz crystals exhibit comparatively high δ18O values, up to 10.2‰, due to magma residence within, and assimilation of, local granite basement. However, some 40% of the analysed quartz crystals display a decrease in δ18O values in outermost growth zones compared to their cores, with values as low as 6.7‰ (maximum ∆core‑rim = 1.8‰). These lower values are consistent with the limited zircon record available for Toba, and the crystallisation history of Toba quartz traces an influx of a low-δ18O component into the magma reservoir just prior to eruption. Here we argue that this late-stage low-δ18O component is derived from hydrothermally-altered roof material. Our study demonstrates that quartz isotope stratigraphy can resolve magmatic events that may remain undetected by whole-rock or zircon isotope studies, and that assimilation of altered roof material may represent a viable eruption trigger in large Toba-style magmatic systems.

  1. Magma reservoir dynamics at Toba caldera, Indonesia, recorded by oxygen isotope zoning in quartz

    Science.gov (United States)

    Budd, David A.; Troll, Valentin R.; Deegan, Frances M.; Jolis, Ester M.; Smith, Victoria C.; Whitehouse, Martin J.; Harris, Chris; Freda, Carmela; Hilton, David R.; Halldórsson, Sæmundur A.; Bindeman, Ilya N.

    2017-01-01

    Quartz is a common phase in high-silica igneous rocks and is resistant to post-eruptive alteration, thus offering a reliable record of magmatic processes in silicic magma systems. Here we employ the 75 ka Toba super-eruption as a case study to show that quartz can resolve late-stage temporal changes in magmatic δ18O values. Overall, Toba quartz crystals exhibit comparatively high δ18O values, up to 10.2‰, due to magma residence within, and assimilation of, local granite basement. However, some 40% of the analysed quartz crystals display a decrease in δ18O values in outermost growth zones compared to their cores, with values as low as 6.7‰ (maximum ∆core−rim = 1.8‰). These lower values are consistent with the limited zircon record available for Toba, and the crystallisation history of Toba quartz traces an influx of a low-δ18O component into the magma reservoir just prior to eruption. Here we argue that this late-stage low-δ18O component is derived from hydrothermally-altered roof material. Our study demonstrates that quartz isotope stratigraphy can resolve magmatic events that may remain undetected by whole-rock or zircon isotope studies, and that assimilation of altered roof material may represent a viable eruption trigger in large Toba-style magmatic systems. PMID:28120860

  2. Magma reservoir dynamics at Toba caldera, Indonesia, recorded by oxygen isotope zoning in quartz.

    Science.gov (United States)

    Budd, David A; Troll, Valentin R; Deegan, Frances M; Jolis, Ester M; Smith, Victoria C; Whitehouse, Martin J; Harris, Chris; Freda, Carmela; Hilton, David R; Halldórsson, Sæmundur A; Bindeman, Ilya N

    2017-01-25

    Quartz is a common phase in high-silica igneous rocks and is resistant to post-eruptive alteration, thus offering a reliable record of magmatic processes in silicic magma systems. Here we employ the 75 ka Toba super-eruption as a case study to show that quartz can resolve late-stage temporal changes in magmatic δ(18)O values. Overall, Toba quartz crystals exhibit comparatively high δ(18)O values, up to 10.2‰, due to magma residence within, and assimilation of, local granite basement. However, some 40% of the analysed quartz crystals display a decrease in δ(18)O values in outermost growth zones compared to their cores, with values as low as 6.7‰ (maximum ∆core-rim = 1.8‰). These lower values are consistent with the limited zircon record available for Toba, and the crystallisation history of Toba quartz traces an influx of a low-δ(18)O component into the magma reservoir just prior to eruption. Here we argue that this late-stage low-δ(18)O component is derived from hydrothermally-altered roof material. Our study demonstrates that quartz isotope stratigraphy can resolve magmatic events that may remain undetected by whole-rock or zircon isotope studies, and that assimilation of altered roof material may represent a viable eruption trigger in large Toba-style magmatic systems.

  3. Looking at Dauphiné twins in vein quartz as a potential paleostress indicator

    Science.gov (United States)

    Sintubin, Manuel; Wenk, Hans-Rudolf

    2013-04-01

    Paleostress studies commonly call upon (1) a fault slip data inversion technique, (2) a calcite twin stress inversion technique, (3) recrystallized grain size piezometry for quartz, or (4) direct measurements of residual lattice strain. Recent advances in orientation imaging microscopy (OIM) using electron backscatter diffraction (EBSD) on a scanning electron microscope (SEM) have revealed that Dauphiné twinning is very common in quartz in naturally deformed quartz-bearing rocks in a wide range of tectonometamorphic conditions. It has long been known that mechanical Dauphiné twinning in quartz can be stress-induced. Based on the results of an extensive EBSD-OIM analysis on vein quartz, taken from well-studied early to late-orogenic veins in the High-Ardenne slate belt (Germany, Belgium), we explore the potential use of mechanical Dauphiné twins as a paleostress indicator, possibly completing our toolbox for reconstructing paleostresses in the Earth's crust. The vein quartz studied precipitated in low-grade tectonometamorphic conditions (~200-400°C), typical for the brittle-plastic transition zone at the base of the seismogenic crust (~7-15km). Quartz has only been weakly affected by low to moderate temperature (200 to 400°C) crystal-plastic deformation. The samples show grains with a high concentration of Dauphiné twin boundaries and others free of twin boundaries, thus being untwinned or completely twinned. This pattern depends on the crystallographic orientation. Twin boundaries are arrested by grain or subgrain boundaries, suggesting that Dauphiné twinning occurred on a pre-existing fabric that resulted from crystal-plastic deformation. An analysis of the orientation distribution of the rhombs in the twinned variant domains of individual quartz (sub-)grains reveals a particular preferred orientation of the poles to rhombs. We will discuss the possible significance of these observations with respect to paleostresses that may have caused the mechanical

  4. Development of Quartz Fiber Calorimetry

    CERN Multimedia

    2002-01-01

    % RD40 \\\\ \\\\ Very Forward Calorimeters (VFCs) in LHC detectors should cover the pseudorapidity range from $\\eta$~=~2.5 to at least $\\eta$~=~5 in order to compute missing transverse energy and for jet tagging. Operation at such high rapidity requires the use of a calorimetry technique that is very radiation resistant, fast and insensitive to radioactivity (especially to neutrons). This can be accomplished through the Quartz-Calorimeter~(Q-Cal) concept of embedding silica core fibers, that resist to the Gigarad radiation level, into an absorber. In this calorimeter the shower particles produce light through the Cherenkov effect generating a signal less than 10~ns in duration. Unique to this new technology the visible energy of hadronic showers has a transverse dimension nearly an order of magnitude smaller than that in conventional calorimeters, enabling precise spatial resolution, sharper isolation cuts and better jet recognition against the minimum bias events background. Last but not least, most radioactive ...

  5. Evidence for residual elastic strain in deformed natural quartz

    Energy Technology Data Exchange (ETDEWEB)

    Kunz, Martin; Chen, Kai; Tamura,Nobumichi; Wenk, Hans-Rudolf

    2009-01-30

    Residual elastic strain in naturally deformed, quartz-containing rocks can be measured quantitatively in a petrographic thin section with high spatial resolution using Laue microdiffraction with white synchrotron x-rays. The measurements with a resolution of one micrometer allow the quantitative determination of the deviatoric strain tensor as a function of position within the crystal investigated. The observed equivalent strain values of 800-1200 microstrains represent a lower bound of the actual preserved residual strain in the rock, since the stress component perpendicular to the cut sample surface plane is released. The measured equivalent strain translates into an equivalent stress in the order of {approx} 50 MPa.

  6. Characterization of hydrothermal green quartz produced by gamma radiation

    Energy Technology Data Exchange (ETDEWEB)

    Enokihara, Cyro T.; Rela, Paulo R., E-mail: cteiti@ipen.br, E-mail: prela06@yahoo.com.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Schultz-Güttler, Rainer A., E-mail: rainersgut@gmail.com [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Geociencias

    2015-07-01

    A specific variety of quartz showing a green color in nature or induced artificially by radiation gamma ({sup 60}Co) is quite rare. Only two occurrences are known today, where this type of quartz can be found: Canada, at the Thunder Bay Amethyst Mine, Ontario and Brazil, at widely scattered geode occurrences along a 600 km stretch from Quarai at Brazils southern most tip to Uberlandia in Minas Gerais. These two occurrences have been formed by strong hydrothermal activities.That way much quartz crystals showed a very fast growth history facilitating the formation of growth defects (twinning, small angle tilting, mosaic growth, striations) and the uptake of water in form of micro inclusions, molecular water, silanol (Si-OH) and OH. In the present work the material analyzed is from hydrothermal regimes found in intrusions of basaltic rocks located in the Rio Grande do Sul state. To characterize these materials, colored green by gamma rays, analyses by ICP, electron microscopy, water loss techniques and UV-VIS or NIR-FTIR spectroscopic measurements have been made. Silanol complexes are formed, which by radiation due to gamma rays form the color center NBOHC (Non-bonding Oxygen Hole Center), showing absorption between 590 to 620 nm, responsible for the green color. The water content with up to 3200 ppm by weight exceeds the amount of charge balancing cations (Fe, Al, Li). There is no correlation between water content and cations as in other color varieties. (author)

  7. Development of a high-pressure microbalance for hydrogen storage materials

    DEFF Research Database (Denmark)

    Vestbø, Andreas Peter; Jensen, Jens Oluf; Bjerrum, Niels

    2007-01-01

    Pressure-composition isotherms (PCI's) help to determine thermodynamic properties related to hydrogen uptake of materials. PCI's are normally obtained volumetrically with a Sieverts type apparatus or gravimetrically with a microbalance. A potential problem with the gravimetric technique is that t...

  8. The Problem of using Quartz as a radiation dosimeter: fundamentals of dose dependence

    Science.gov (United States)

    King, G. E.; Finch, A. A.; Robinson, R. A. J.; Hole, D. E.

    2009-04-01

    Quartz is widely used as a radiation dosimeter in Quaternary geomorphological and archaeological dating applications through Optically Stimulated Luminescence (over 1,200 journal publications since 2000). However, obtaining an accurate equivalent radiation dose (DE) can be challenging, especially where the luminescence intensity of the quartz is dim. The causes of variation in luminescence intensity between quartz grains of different provenances, transport and thermal histories is unknown, however it has been suggested that it relates to either the dosimetric history of the grain, or mechanical processes which occur in transit. Investigation of the fundamental properties of the luminescence of quartz, enables investigation of dose dependent changes in luminescence intensity. A series of dose dependence experiments were conducted using spectroscopic ionoluminescence, which comprises the excitation of quartz with protons accelerated at 0.95 MeV. The energy delivered to the sample throughout ion implantation is similar to that received during gamma irradiation, and thus approximates sample radiation dosing. A natural macro-crystal of α-quartz was investigated parallel and perpendicular to c, to observe any orientation dependent effects, as well as a calibration quartz from the Risø National Laboratory, Denmark, and a Scottish geomorphological sample, prepared using standard laboratory procedures. The calibration quartz sample has excellent luminescence intensity and is suited to analysis using the single-aliquot regenerative dose (SAR) standard OSL protocol, the Scottish sample alternatively has very dim luminescence and exhibits variable behaviour when analysed with SAR. Despite the differences between the luminescence behaviour of the samples, all three responded to the dose dependence experiments in a similar manner. The UV/blue emission was observed to deplete with increasing dose, whereas the red emission, not normally analysed within OSL, exhibited increased

  9. Mineralogy, morphology, and textural relationships in coatings on quartz grains in sediments in a quartz-sand aquifer.

    Science.gov (United States)

    Zhang, Shouliang; Kent, Douglas B; Elbert, David C; Shi, Zhi; Davis, James A; Veblen, David R

    2011-06-01

    Mineralogical studies of coatings on quartz grains and bulk sediments from an aquifer on Western Cape Cod, Massachusetts, USA were carried out using a variety of transmission electron microscopy (TEM) techniques. Previous studies demonstrated that coatings on quartz grains control the adsorption properties of these sediments. Samples for TEM characterization were made by a gentle mechanical grinding method and focused ion beam (FIB) milling. The former method can make abundant electron-transparent coating assemblages for comprehensive and quantitative X-ray analysis and the latter technique protects the coating texture from being destroyed. Characterization of the samples from both a pristine area and an area heavily impacted by wastewater discharge shows similar coating textures and chemical compositions. Major constituents of the coating include Al-substituted goethite and illite/chlorite clays. Goethite is aggregated into well-crystallized domains through oriented attachment resulting in increased porosity. Illite/chlorite clays with various chemical compositions were observed to be mixed with goethite aggregates and aligned sub-parallel to the associated quartz surface. The uniform spatial distribution of wastewater-derived phosphorus throughout the coating from the wastewater-contaminated site suggests that all of the coating constituents, including those adjacent to the quartz surface, are accessible to groundwater solutes. Both TEM characterization and chemical extraction results indicate there is a significantly greater amount of amorphous iron oxide in samples from wastewater discharge area compared to those from the pristine region, which might reflect the impact of redox cycling of iron under the wastewater-discharge area. Coating compositions are consistent with the moderate metal and oxy-metalloid adsorption capacities, low but significant cation exchange capacities, and control of iron(III) solubility by goethite observed in reactive transport

  10. High-Ti, bright-CL rims in volcanic quartz: a result of very rapid growth

    Science.gov (United States)

    Pamukcu, Ayla S.; Ghiorso, Mark S.; Gualda, Guilherme A. R.

    2016-12-01

    Volcanic quartz commonly contains Ti-enriched zones and CO2-enriched melt inclusions, and crystallization temperatures and pressures derived from Ti-in-quartz geothermobarometry and H2O-CO2 glass geobarometry applied to these compositions are typically high. Consequently, these features are generally interpreted to represent high temperatures and/or pressures. Yet, growth rate estimates from some high-Ti/bright-CL quartz rims suggest they grew at rates orders of magnitude faster than did cores and interiors of the crystals. This observation is notable in light of studies that suggest that fast crystal growth rates can produce a boundary layer in the melt surrounding a growing crystal that is enriched in components that diffuse comparatively slowly in the melt. In these circumstances, the composition of zones or melt inclusions formed from such a boundary layer melt will not accurately represent that of the far-field melt, and temperatures and pressures estimated from these compositions will be anomalous. We use a numerical model based on the coupled growth-diffusion equation of Lasaga (1982) to assess the effect of growth rate on the production of high-Ti/bright-CL zones and high-CO2 melt inclusions in quartz in rhyolitic melts. Simulations span a wide range of growth rates (10-7 to 10-13 m/s) and timescales (1 minute-1 year), and results suggest that quartz growth at 10-10 m/s or faster can produce a boundary layer enriched in these components. This suggests that appropriate application of Ti-in-quartz and H2O-CO2 glass geothermobarometry is contingent upon the verification that the compositions used are not those of boundary layer melts. Applying our model to the Bishop Tuff, which contains quartz displaying high-Ti/bright-CL rims and high-CO2 rim-hosted melt inclusions, we find that growth rates of 10-7 to 10-9 m/s can produce the observed enrichments in these components over the timescales estimated for the growth of the rims (days-weeks); these growth rates

  11. Testing the isotropy of space using rotating quartz oscillators

    CERN Document Server

    Lo, Anthony; Mizrachi, Eli; Anderegg, Loic; Müller, Holger; Hohensee, Michael; Goryachev, Maxim; Tobar, Michael E

    2014-01-01

    Violations of Lorentz invariance by matter and light can generate direction- and frame-dependent anisotropies in particles inertial masses and, hence, a measurable modulation of the oscillation frequency of rotating quartz crystal oscillators. This allows simple and low maintenance experiments that are ideally suited for long-term data taking. Using the Standard Model Extension (SME) as a parameterizing framework, we study the magnitude of this putative frequency modulation. A preliminary experiment with room-temperature SC-cut crystals yields a frequency resolution in the $10^{-15}$ range with $\\sim 120$ hours of data and a limit of $\\tilde c_Q=(-1.8 \\pm 2.2)\\times 10^{-14}$\\,GeV on the most weakly constrained neutron-sector $c-$coefficient of the SME. Future experiments with cryogenic oscillators promise additional improvements in accuracy, opening up the potential for improved tests of Lorentz symmetry in the neutron, proton, electron and photon sector.

  12. Preparation of Macroporous Epitaxial Quartz Films on Silicon by Chemical Solution Deposition.

    Science.gov (United States)

    Carretero-Genevrier, Adrián; Gich, Martí

    2015-12-21

    This work describes the detailed protocol for preparing piezoelectric macroporous epitaxial quartz films on silicon(100) substrates. This is a three-step process based on the preparation of a sol in a one-pot synthesis which is followed by the deposition of a gel film on Si(100) substrates by evaporation induced self-assembly using the dip-coating technique and ends with a thermal treatment of the material to induce the gel crystallization and the growth of the quartz film. The formation of a silica gel is based on the reaction of a tetraethyl orthosilicate and water, catalyzed by HCl, in ethanol. However, the solution contains two additional components that are essential for preparing mesoporous epitaxial quartz films from these silica gels dip-coated on Si. Alkaline earth ions, like Sr(2+) act as glass melting agents that facilitate the crystallization of silica and in combination with cetyl trimethylammonium bromide (CTAB) amphiphilic template form a phase separation responsible of the macroporosity of the films. The good matching between the quartz and silicon cell parameters is also essential in the stabilization of quartz over other SiO2 polymorphs and is at the origin of the epitaxial growth.

  13. Fission Track Dating of Authigenic Quartz in Red Weathering Crusts of Carbonate Rocks in Guizhou Province

    Institute of Scientific and Technical Information of China (English)

    LIU Xiuming; WANG Shijie; ZHANG Feng

    2004-01-01

    The Cenozoic evolution history of Guizhou Province, which is located on the southeastem flank of the Qinghai-Tibet Plateau, is unclear because of the lack of sedimentation records. The red weathering crusts widespread on the Yunnan-Guizhou Plateau may bear critical information about their evolution history. This work firstly determined the ages of four red weathering crusts in eastern, central and northern Guizhou. The material used in fission track dating is well-crystallized quartz occurring in many in-situ weathering crusts of carbonate rocks. The results showed that the fission track ages of quartz vary over a wide range from 1 to 25 Ma in the four profiles, significantly younger than the ages of the Triassic and Cambrian parent rocks. In combination with the evolution history of the regional geology during the period from 25 to 1 Ma, the ages of quartz can exclude the possibility that the origin of quartz has nothing to do with primary clastic minerals in parent rocks, authigenesis during diagenesis and hydrothermal precipitation or replacement by volcanic activities. It is deduced that the well-crystallized quartz was precipitated from Si-rich weathering fluids during the weathering process of carbonate rocks. The recorded ages of quartz from the four profiles are consistent with the episodes of the planation surfaces on the Qinghai-Tibet Plateau, the forming stages of red soil in the tropics of South China, the tectonically stable periods in Guizhou, and the ages of weathering in other parts of the world during the Cenozoic era. That is to say, the ages of authigenic quartz dated by the fission track method are well feasible and credible.

  14. Photolithography and Selective Etching of an Array of Quartz Tuning Fork Resonators with Improved Impact Resistance Characteristics

    Science.gov (United States)

    Lee, Sungkyu

    2001-08-01

    Quartz tuning fork blanks with improved impact-resistant characteristics for use in Qualcomm mobile station modem (MSM)-3000 central processing unit (CPU) chips for code division multiple access (CDMA), personal communication system (PCS), and global system for mobile communication (GSM) systems were designed using finite element method (FEM) analysis and suitable processing conditions were determined for the reproducible precision etching of a Z-cut quartz wafer into an array of tuning forks. Negative photoresist photolithography for the additive process was used in preference to positive photoresist photolithography for the subtractive process to etch the array of quartz tuning forks. The tuning fork pattern was transferred via a conventional photolithographical chromium/quartz glass template using a standard single-sided aligner and subsequent negative photoresist development. A tightly adhering and pinhole-free 600/2000 Å chromium/gold mask was coated over the developed photoresist pattern which was subsequently stripped in acetone. This procedure was repeated on the back surface of the wafer. With the protective metallization area of the tuning fork geometry thus formed, etching through the quartz wafer was performed at 80°C in a ± 1.5°C controlled bath containing a concentrated solution of ammonium bifluoride to remove the unwanted areas of the quartz wafer. The quality of the quartz wafer surface finish after quartz etching depended primarily on the surface finish of the quartz wafer prior to etching and the quality of quartz crystals used. Selective etching of a 100 μm quartz wafer could be achieved within 90 min at 80°C. A selective etching procedure with reproducible precision has thus been established and enables the photolithographic mass production of miniature tuning fork resonators.

  15. A study of cathodoluminescence and trace element compositional zoning in natural quartz from volcanic rocks: mapping titanium content in quartz.

    Science.gov (United States)

    Leeman, William P; MacRae, Colin M; Wilson, Nick C; Torpy, Aaron; Lee, Cin-Ty A; Student, James J; Thomas, Jay B; Vicenzi, Edward P

    2012-12-01

    This article concerns application of cathodoluminescence (CL) spectroscopy to volcanic quartz and its utility in assessing variation in trace quantities of Ti within individual crystals. CL spectroscopy provides useful details of intragrain compositional variability and structure but generally limited quantitative information on element abundances. Microbeam analysis can provide such information but is time-consuming and costly, particularly if large numbers of analyses are required. To maximize advantages of both approaches, natural and synthetic quartz crystals were studied using high-resolution hyperspectral CL imaging (1.2-5.0 eV range) combined with analysis via laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Spectral intensities can be deconvolved into three principal contributions (1.93, 2.19, and 2.72 eV), for which intensity of the latter peak was found to correlate directly with Ti concentration. Quantitative maps of Ti variation can be produced by calibration of the CL spectral data against relatively few analytical points. Such maps provide useful information concerning intragrain zoning or heterogeneity of Ti contents with the sensitivity of LA-ICPMS analysis and spatial resolution of electron microprobe analysis.

  16. SAW Temperature Sensor on Quartz.

    Science.gov (United States)

    Zhgoon, Sergei; Shvetsov, Alexander; Ancev, Ivan; Bogoslovsky, Sergei; Sapozhnikov, Gennadiy; Trokhimets, Konstantin; Derkach, Mikhail

    2015-06-01

    For biomedical applications, narrow temperature range and high sensor accuracy requirements define the need for high temperature sensitivity. Wireless SAW sensors connected to antennas need a reference element to account for changes in electromagnetic coupling between the transmitter and receiver antennas. A pair of sensors with different temperature sensitivities may serve as a self-referenced sensor assembly. This justifies the need for materials with useful SAW resonator properties and with the largest difference between temperature coefficients of frequency (TCF) for a resonator pair on a single substrate. We have identified several cuts of quartz having useful properties with a TCF difference up to 140 ppm/°C for a pair of resonators on a single substrate. As a rule, placing such resonators on a single substrate requires their rotation by up to 90° relative to each other. The limited range of cuts presents a unique opportunity to place both resonators along the X+90° direction with one resonator using Bleustein-Gulyaev-Shimizu (BGS) waves (with electrodes placed along the x-axis) and the other one (with electrodes inclined by about ±10° to the x-axis) using quasi-Rayleigh waves. These cuts are close to the 70°Y cut where a high TCF difference is reached together with acceptable characteristics of the resonators. Resonators were designed for all useful cuts (including the 70°Y cut) and tested. The use of different periods in reflectors and interdigital transducer (IDT) together with individual choice of gaps between reflectors and IDT meant achieving low spurious content in resonator responses. The quality factors reached values up to 3500 at central frequencies around 915 MHz for both BGS and quasi-Rayleigh types of waves. The measured difference of the TCF is about 138 ppm/°C on 70°Y cut that is close to the calculated value.

  17. Effect of high gamma-doses in the sensitization of natural quartz for thermoluminescence dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Khoury, H.J.; Guzzo, P.L.; Brito, S.B. [Universidade Federal de Pernambuco, 50740-540 Recife PE (Brazil)

    2006-07-01

    Sensitization is an important effect in radiation dosimetry using thermoluminescent (TL materials where the enhancement of sensitivity is a desirable feature. Until known, the investigation of sensitization in quartz has been restricted to its first glow peak appearing around 110 C. In addition, the sensitization process has been essentially produced by heat-treatments in powdered quartz. The aim of this study is to investigate the sensitization process in the second glow peak of crystalline quartz using high doses of gamma irradiation. For this, five lots of samples were prepared from quartz single crystals issued from different geologies in Brazil. Chips of 5 x 5 x 1 mm{sup 3} (60 mg) were cut and lapped parallel to the (0001) plane. The specimens were initially irradiated with doses of gamma radiation of {sup 137} Cs in the range of 10 mGy to 10 Gy in order to determine its TL response curve. After that, the specimens were submitted to successive high doses of gamma-irradiation with {sup 60} Co from 25 kGy to 350 kGy. After each irradiation, the TL response curves to gamma radiation of {sup 137} Cs were determined for each quartz lot irradiated in the range of 2 to 20 mGy. The TL measurements were carried out with a 2800M Victoreen reader using the step mode. The step parameters were set in 10 s from 30 to 160 C (first region) and in 20 s from 160 to 320 C (second region). The absolute TL signal used to obtain the calibration curves represented the sum of electric charges under the glow peak appearing in the second region. The results showed that the TL response of the quartz studied increased with the dose sensitization, so that the TL response for 10mGy of {sup 137} Cs radiation varied from 0.05 nC/mg for the quartz without sensitization to 10 nC/mg after a sensitization with 50 kGy of gamma radiation of {sup 60} Co. The effect of sensitization with high doses of gamma irradiation was clearly observed for three quartz lots and it was observed that the high

  18. Quartz-Enhanced Photoacoustic Spectroscopy: A Review

    Directory of Open Access Journals (Sweden)

    Pietro Patimisco

    2014-03-01

    Full Text Available A detailed review on the development of quartz-enhanced photoacoustic sensors (QEPAS for the sensitive and selective quantification of molecular trace gas species with resolved spectroscopic features is reported. The basis of the QEPAS technique, the technology available to support this field in terms of key components, such as light sources and quartz-tuning forks and the recent developments in detection methods and performance limitations will be discussed. Furthermore, different experimental QEPAS methods such as: on-beam and off-beam QEPAS, quartz-enhanced evanescent wave photoacoustic detection, modulation-cancellation approach and mid-IR single mode fiber-coupled sensor systems will be reviewed and analysed. A QEPAS sensor operating in the THz range, employing a custom-made quartz-tuning fork and a THz quantum cascade laser will be also described. Finally, we evaluated data reported during the past decade and draw relevant and useful conclusions from this analysis.

  19. Quartz-enhanced photoacoustic spectroscopy: a review.

    Science.gov (United States)

    Patimisco, Pietro; Scamarcio, Gaetano; Tittel, Frank K; Spagnolo, Vincenzo

    2014-03-28

    A detailed review on the development of quartz-enhanced photoacoustic sensors (QEPAS) for the sensitive and selective quantification of molecular trace gas species with resolved spectroscopic features is reported. The basis of the QEPAS technique, the technology available to support this field in terms of key components, such as light sources and quartz-tuning forks and the recent developments in detection methods and performance limitations will be discussed. Furthermore, different experimental QEPAS methods such as: on-beam and off-beam QEPAS, quartz-enhanced evanescent wave photoacoustic detection, modulation-cancellation approach and mid-IR single mode fiber-coupled sensor systems will be reviewed and analysed. A QEPAS sensor operating in the THz range, employing a custom-made quartz-tuning fork and a THz quantum cascade laser will be also described. Finally, we evaluated data reported during the past decade and draw relevant and useful conclusions from this analysis.

  20. Quartz Mountain/Oklahoma Summer Arts Institute.

    Science.gov (United States)

    Frates, Mary Y.; Madeja, Stanley S.

    1982-01-01

    Describes the Quartz Mountain Oklahoma Summer Arts Institute program. It is designed to nurture artistic talent and to provide intensive arts experiences in music, dance, theater, and the visual arts for talented students aged 14-18. (AM)

  1. Visualizing trace element distribution in quartz using cathodoluminescence, electron microprobe, and laser ablation-inductively coupled plasma-mass spectrometry

    Science.gov (United States)

    Rusk, Brian; Koenig, Alan; Lowers, Heather

    2011-01-01

    Cathodoluminescent (CL) textures in quartz reveal successive histories of the physical and chemical fluctuations that accompany crystal growth. Such CL textures reflect trace element concentration variations that can be mapped by electron microprobe or laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Trace element maps in hydrothermal quartz from four different ore deposit types (Carlin-type Au, epithermal Ag, porphyry-Cu, and MVT Pb-Zn) reveal correlations among trace elements and between trace element concentrations and CL textures. The distributions of trace elements reflect variations in the physical and chemical conditions of quartz precipitation. These maps show that Al is the most abundant trace element in hydrothermal quartz. In crystals grown at temperatures below 300 °C, Al concentrations may vary by up to two orders of magnitude between adjacent growth zones, with no evidence for diffusion. The monovalent cations Li, Na, and K, where detectable, always correlate with Al, with Li being the most abundant of the three. In most samples, Al is more abundant than the combined total of the monovalent cations; however, in the MVT sample, molar Al/Li ratios are ~0.8. Antimony is present in concentrations up to ~120 ppm in epithermal quartz (~200–300 °C), but is not detectable in MVT, Carlin, or porphyry-Cu quartz. Concentrations of Sb do not correlate consistently with those of other trace elements or with CL textures. Titanium is only abundant enough to be mapped in quartz from porphyry-type ore deposits that precipitate at temperatures above ~400 °C. In such quartz, Ti concentration correlates positively with CL intensity, suggesting a causative relationship. In contrast, in quartz from other deposit types, there is no consistent correlation between concentrations of any trace element and CL intensity fluctuations.

  2. Comparison characteristics of surface acoustic waves propagating on LGT and quartz substrates

    Institute of Scientific and Technical Information of China (English)

    ZHANG Guowei; SHI Wenkang; JI Xiaojun; HAN Tao

    2004-01-01

    For comprehending the propagation characteristics of surface acoustic waves (SAW) on novel piezoelectric crystal Langatate (LGT), the numerical analysis of the most important propagation characteristics of surface acoustic waves (SAW) on LGT are presented and compared with that of quartz. The results are that the phase velocity on LGT is generally about 1000 m/s slower than that on quartz; there are zero temperature cuts and pure mode directions on LGT; the electromechanical coupling coefficient (K2) of LGT is larger than that of quartz. The results show that LGT has lower propagation velocity, higher electromechanical coupling coefficient, good temperature stability and other good characteristic. The results also show that there are somewhat deviations with different material constants, especially, the temperature coefficient of frequency.

  3. Electric field cancellation on quartz by Rb adsorbate-induced negative electron affinity

    Science.gov (United States)

    Shaffer, James

    2016-05-01

    We investigate the (0001) surface of single crystal quartz with a submonolayer of Rb adsorbates. Using Rydberg atom electromagnetically induced transparency, we investigate the electric fields resulting from Rb adsorbed on the quartz surface, and measure the activation energy of the Rb adsorbates. We show that the adsorbed Rb induces a negative electron affinity (NEA) on the quartz surface. The NEA surface allows low energy electrons to bind to the surface and cancel the electric field from the Rb adsorbates. Our results are important for integrating Rydberg atoms into hybrid quantum systems and the fundamental study of atom-surface interactions, as well as applications for electrons bound to a 2D surface. This work was supported by the DARPA Quasar program by a Grant through ARO (60181-PH-DRP) and the AFOSR (FA9550-12-1-0282),.

  4. Automated X-ray Orientation for Quartz Crystal Resonators.

    Science.gov (United States)

    1981-09-01

    stepping rate imposed by the motor and controller of 2000 steps/sec. Thus, the maximum time spent in the initial reflec- tion search will be 18 sec/blank...rotational adjustment in each of these planes. 26 Subsequent realization by ARACOR that the outboard detectors must now have rotational capabilities imposed ...218.12, HKL MAAX=3 8/25 133’ 2 02 3’. % % 3 ’ 223 2 S\\ \\ 2 2 P 32 1 L -P j C8 A Ji-’ oI I - 2 2~ 1 ’ g 1 3 *𔃽’ 2 3 2 2 3 1 ’ 57 Figurae 6. AT PATTERN

  5. Crystallization of hollow mesoporous silica nanoparticles.

    Science.gov (United States)

    Drisko, Glenna L; Carretero-Genevrier, Adrian; Perrot, Alexandre; Gich, Martí; Gàzquez, Jaume; Rodriguez-Carvajal, Juan; Favre, Luc; Grosso, David; Boissière, Cédric; Sanchez, Clément

    2015-03-11

    Complex 3D macrostructured nanoparticles are transformed from amorphous silica into pure polycrystalline α-quartz using catalytic quantities of alkaline earth metals as devitrifying agent. Walls as thin as 10 nm could be crystallized without losing the architecture of the particles. The roles of cation size and the mol% of the incorporated devitrifying agent in crystallization behavior are studied, with Mg(2+), Ca(2+), Sr(2+) and Ba(2+) all producing pure α-quartz under certain conditions.

  6. Brittle–viscous deformation of vein quartz under fluid-rich low greenschist facies conditions

    Directory of Open Access Journals (Sweden)

    H. J. Kjøll

    2015-01-01

    Full Text Available A coarse grained, statically crystallized quartz vein, embedded in a phyllonitic matrix, was studied by EBSD and optical microscopy to gain insights into the processes of strain localization in quartz deformed under low-grade conditions, broadly coincident with the frictional–viscous transition. The vein is from a high strain zone at the front of the Porsa Imbricate Stack in the Paleoproterozoic Repparfjord Tectonic Window in northern Norway. The vein was deformed under lower greenschist facies conditions during deformation along a large out-of-sequence phyllonitic thrust of Caledonian age. The host phyllonite formed at the expense of metabasalt wherein feldspar broke down to form interconnected layers of fine, synkinematic phyllosilicates. In the mechanically weak framework of the phyllonite, the studied quartz vein acted as a relatively rigid body deforming mainly by coaxial strain. Viscous deformation was initially accommodated by basal ⟨a⟩ slip of quartz during the development of a mesoscopic pervasive extensional crenulation cleavage. Under the prevailing boundary conditions, however, dislocation glide-accommodated deformation of quartz resulted inefficient and led to dislocation tangling and strain hardening of the vein. In response to hardening, to the progressive increase of fluid pressure and the increasing competence contrast between the vein and the weak foliated host phyllonite, quartz crystals began to deform frictionally along specific, optimally oriented lattice planes, creating microgouges along microfractures. These were, however, rapidly sealed by nucleation of new grains as transiently over pressured fluids penetrated the deforming system. The new nucleated grains grew initially by solution-precipitation and later by grain boundary migration. Due to the random initial orientation of the vein crystals, strain was accommodated differently in the individual crystals, leading to the development of remarkably different

  7. Influence of the preshock temperature on shock effects in quartz

    Science.gov (United States)

    Langenhorst, F.; Deutsch, A.

    1992-01-01

    Shock metamorphic features are the prime indicators for recognizing impact phenomena on Earth and other planetary bodies. Although the pressure dependence of shock features is well known, information about the influence of the preshock temperature is almost lacking. Especially in the case of large-scale impacts like Sudbury, it is expected that deep-seated crustal rocks were subjected to shock at elevated temperatures. Therefore, we continued to perform shock experiments at elevated temperatures on less than 0.5-mm thin disks of single crystal quartz cut parallel to the (1010) face. All recovered quartz samples were investigated by universal stage, spindle stage, and a newly developed density gradient technique. Errors of refractive index and density measurements are +/- 0.0005 and +/- 0.002 g/cu cm respectively. Our investigations indicate that shock metamorphic features are strongly dependent on the preshock temperature. This statement has far-reaching implications with respect to shock wave barometry that is based on data from recovery experiments at room temperature. These datasets might be applicable only to low-temperature target rocks. Moreover, this study demonstrates that shock recovery experiments are definitely required for understanding the complete pressure-temperature regime of shock metamorphism on planetary bodies.

  8. Flux-Grown Piezoelectric Materials: Application to α-Quartz Analogues

    Directory of Open Access Journals (Sweden)

    Pascale Armand

    2014-06-01

    Full Text Available Using the slow-cooling method in selected MoO3-based fluxes, single-crystals of GeO2 and GaPO4 materials with an α-quartz-like structure were grown at high temperatures (T ≥ 950 °C. These piezoelectric materials were obtained in millimeter-size as well-faceted, visually colorless and transparent crystals. Compared to crystals grown by hydrothermal methods, infrared and Raman measurements revealed flux-grown samples without significant hydroxyl group contamination and thermal analyses demonstrated a total reversibility of the α-quartz ↔ β-cristobalite phase transition for GaPO4 and an absence of phase transition before melting for α-GeO2. The elastic constants CIJ (with I, J indices from 1 to 6 of these flux-grown piezoelectric crystals were experimentally determined at room and high temperatures. The ambient results for as-grown α-GaPO4 were in good agreement with those obtained from hydrothermally-grown samples and the two longitudinal elastic constants measured versus temperature up to 850 °C showed a monotonous evolution. The extraction of the ambient piezoelectric stress contribution e11 from the CD11 to CE11 difference gave for the piezoelectric strain coefficient d11 of flux-grown α-GeO2 crystal a value of 5.7(2 pC/N, which is more than twice that of α-quartz. As the α-quartz structure of GeO2 remained stable up to melting, a piezoelectric activity was observed up to 1000 °C.

  9. Measurement of fluid viscosity at microliter volumes using quartz impedance analysis.

    Science.gov (United States)

    Saluja, Atul; Kalonia, Devendra S

    2004-08-05

    The purpose of this work was to measure viscosity of fluids at low microliter volumes by means of quartz crystal impedance analysis. To achieve this, a novel setup was designed that allowed for measurement of viscosity at volumes of 8 to 10 microL. The technique was based on the principle of electromechanical coupling of piezoelectric quartz crystals. The arrangement was simple with measurement times ranging from 2 to 3 minutes. The crystal setup assembly did not impose any unwanted initial stress on the unloaded quartz crystal. Quartz crystals of 5- and 10-MHz fundamental frequency were calibrated with glycerol-water mixtures of known density and viscosity prior to viscosity measurements. True frequency shifts, for the purpose of this work, were determined followed by viscosity measurement of aqueous solutions of sucrose, urea, PEG-400, glucose, and ethylene glycol at 25 degrees C +/- 0.5 degrees C. The measured viscosities were found to be reproducible and consistent with the values reported in the literature. Minor inconsistencies in the measured resistance and frequency shifts did not affect the results significantly, and were found to be experimental in origin rather than due to electrode surface roughness. Besides, as expected for a viscoelastic fluid, PEG 8000 solutions, the calculated viscosities were found to be less than the reported values due to frequency dependence of storage and loss modulus components of complex viscosity. From the results, it can be concluded that the present setup can provide accurate assessment of viscosity of Newtonian fluids and also shows potential for analyzing non-Newtonian fluids at low microliter volumes.

  10. PULSED ELECTROCHEMICAL TECHNIQUE FOR MONITORING ANTIBODY-ANTIGEN REACTIONS AT INTERFACES. (R825323)

    Science.gov (United States)

    AbstractThe mechanism of pulsed potential waveform for monitoring antibody¯antigen interactions at immunosensor interfaces is discussed. Some examples of antibody¯antigen interactions at quartz crystal microbalance and polymer-modified ...

  11. Ion and solvent Transport in Polypyrrole: Experimental Test of Osmotic Model

    DEFF Research Database (Denmark)

    Velmurugu, Yogambigai; Skaarup, Steen

    2005-01-01

    Ion and solvent transport in the conjugated polymer actuator material, polypyrrole, doped with the immobile anion dodecyl benzene sulphonate, has been investigated by simultaneous cyclic voltammetry and Electrochemical Quartz Crystal Microbalance measurements. The purpose was to elucidate...

  12. Multiwalled Carbon Nanotube Deposition on Model Environmental Surfaces

    Science.gov (United States)

    Deposition of multiwalled carbon nanotubes (MWNTs) on model environmental surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Deposition behaviors of MWNTs on positively and negatively charged surfaces were in good agreement with Der...

  13. Ion Movement in Polypyrrole/Dodecylbenzenesulphonate Films in aqueous and non-aqueous electrolytes

    DEFF Research Database (Denmark)

    Vidanapathirana, K.; Careem, M.A.; Skaarup, Steen

    2002-01-01

    The electrochemical characteristics during the redox process of polypyrrole (PPy) films, prepared using dodecylbenzenesulphonate (DBS-) dopant species, have been investigated using a combination of cyclic voltammetry and Electrochemical Quartz Crystal Microbalance (EQCM) measurements...

  14. Multiwalled Carbon Nanotube Deposition on Model Environmental Surfaces

    Science.gov (United States)

    Deposition of multiwalled carbon nanotubes (MWNTs) on model environmental surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Deposition behaviors of MWNTs on positively and negatively charged surfaces were in good agreement with Der...

  15. The Shahewan rapakivi-textured granite – quartz monzonite pluton, Qinling orogen, central China: mineral composition and petrogenetic significance

    Directory of Open Access Journals (Sweden)

    Xiaoxia Wang

    2002-01-01

    Full Text Available The Mesozoic Shahewan pluton consists of four texturally different types of biotite-hornblende quartz monzonite. In the porphyritic types alkali feldspar occurs as euhedral or ovoidal megacrysts that are often mantled by one or more plagioclase shells, and as smaller grains in the groundmass. Quartz, plagioclase (An20–28, biotite, and hornblende occur as inclusions in the alkali feldspar megacrystsand, more abundantly, in the groundmass. Euhedral quartz crystals in the groundmass are not as common and well developed as in typical rapakivi granite. Compared to typical rapakivi granites, the mafic minerals (biotite and hornblende are rich in Mg and poor in Fe, and the whole rock is low in Si, K, F, Ga, Zr, LREE, Fe/Mg, and K/Na. The rocks of the Shahewan pluton are thus regarded as rapakivi-textured quartz monzonites and granites but not true rapakivi granites.

  16. Estimating Quartz Reserves Using Compositional Kriging

    Directory of Open Access Journals (Sweden)

    J. Taboada

    2013-01-01

    Full Text Available The aim of this study was to determine spatial distribution and volume of four commercial quartz grades, namely, silicon metal, ferrosilicon, aggregate, and kaolin (depending on content in impurities in a quartz seam. The chemical and mineralogical composition of the reserves in the seam were determined from samples collected from outcrops, blasting operations, and exploratory drilling, and compositional kriging was used to calculate the volume and distribution of the reserves. A more accurate knowledge of the deposit ensures better mine planning, leading to higher profitability and an improved relationship with the environment.

  17. Shock experiments on pre-heated alpha- and beta-quartz: 1. Optical and density data

    Science.gov (United States)

    Langenhorst, Falko; Deutsch, Alexander

    1994-07-01

    Discs of single crystal quartz, unheated, and pre-heated to 275 C and 540 C (i.e., alpha-quartz) and 630 C (i.e., beta-quartz) were experimentally shocked to pressures ranging from 20 to 40 GPa, with the shock front propagating parallel to either (10-10) or (0001). Refractive indices, density and the orientation of planar deformation features (PDFs) were determined on the recovered quartz samples. Refractive indices of pre-heated quartz are unaffected up to 25 GPa but density starts to decrease slightly up to this pressure. Above 25 GPa, pre-heating causes drastic variations: Refractive indices and birefringence of quartz shocked at ambient temperature decrease continuously, until complete isotropization is reached at 35 GPa. In quartz shocked at 630 C, refractivity drops discontinuously in the interval from 25 to 26 GPa, and complete transformation to diaplectic glass is reached at 26 GPa. Density follows the trends demonstrated by the optical parameters, with higher pre-shock temperatures yielding lower density at a given shock pressure. These results indicate that the threshold pressure for the onset of transformation to diaplectic quartz glass is largely temperature-invariant, lying at 25 GPa, whereas the pressure limit for complete transformation decreases with increasing pre-shock temperature from approximately equal 35 to approximately equal 26 GPa. Quartz shocked parallel to (0001) always has a higher density and refractivity than that shocked parallel to (10-10), indicating a significant influence of the structural anisotropy. This is also evident from the distribution of PDF orientations. Pressures greater than or equal 25 GPa cause, in quartz shocked parallel to (10-10), PDFs that are predominantly oriented parallel to set of (10-12) planes, while quartz shocked to the same pressures but parallel to (0001) contains almost exclusively PDFs parallel to set of (10-13) planes. PDF orientations in quartz shocked at ambient temperature parallel to (10-10) show

  18. Bubble Formation in Silicon-Quartz Interface

    OpenAIRE

    Kakimoto, K.; EGUCHI, M.; Ozoe, H.

    1997-01-01

    Bubble formation at an interface between silicon melt and a quartz crucible was studied by thermodynamical calculation and visualization of bubble formation using X-ray radiography. A phase diagram of silicon-oxygen (Si-O) system is also calculated from the reported thermodynamical data. Critical temperature and radius of bubble formation at the interface was discussed.

  19. Time-resolved luminescence from quartz

    NARCIS (Netherlands)

    Chithambo, M.L.; Ankjærgaard, C.; Pagonis, V.

    2016-01-01

    Time-resolved optical stimulation of luminescence has become established as a key method for measurement of optically stimulated luminescence from quartz, feldspar and α-Al2O3:C, all materials of interest in dosimetry. The aim of time-resolved optical stimulation is to separ

  20. Identifying well-bleached quartz using the different bleaching rates of quartz and feldspar luminescence signals

    DEFF Research Database (Denmark)

    Murray, A.S.; Thomsen, Kristina Jørkov; Masuda, N.;

    2012-01-01

    When dating older sedimentary deposits using quartz, there are no unambiguous methods for identifying the presence of incomplete bleaching. Current statistical analysis of dose distributions depends entirely on the assumption that incomplete bleaching and mixing are the main causes of any excess...... in relative bleaching rates of quartz optically stimulated luminescence (OSL) and feldspar luminescence stimulated at 50 °C by infrared light (IR50) and feldspar luminescence stimulated at 290 °C by infrared light after a stimulation at 50 °C (pIRIR290), and use recently deposited samples to determine...... that the large aliquot data are more likely to be correct. We conclude that a comparison of quartz and feldspar doses provides a useful independent method for identifying well-bleached quartz samples, and that it is unwise to apply statistical models to dose distributions without clear evidence for the physical...

  1. Dissolution of quartz in aqueous basic solution, 106-236 C - Surface kinetics of 'perfect' crystallographic faces

    Science.gov (United States)

    Gratz, Andrew J.; Bird, Peter; Quiro, Glenn B.

    1990-01-01

    A highly accurate method, called the negative crystal method, for determining the rate of dissolution on specific crystallographic faces of crystals was developed, in which the dissolution rates of nominally perfect crystal faces are obtained by measuring the size of individual negative crystals during a sequence of dissolution steps. The method was applied to determine the apparent activation energy and rate constants for the dissolution of quartz in 0.01 M KOH solutions at temperatures from 106 to 236 C. Also investigated were the effects of hydroxyl activity and ionic strength. The apparent activation energies for the dissolution of the prism and of the rhomb were determined.

  2. Hydrothermal quartz formation during fluctuations of brittle shear-zone activity and fluid flow: grain growth and deformation structures of the Pfahl shear zone (Germany)

    Science.gov (United States)

    Yilmaz, T.; Prosser, G.; Liotta, D.; Kruhl, J. H.

    2012-12-01

    The Bavarian Pfahl shear zone is a WNW-ESE trending dextral strike-slip shear zone at the SW margin of the Bohemian Massif (Central Europe). It was discontinuously active during decreasing PT-conditions, i.e. from ductile to brittle, from the late-Carboniferous to the late-Cretaceous - Paleocene times. Triassic hydrothermal activity produced a 150 km long and 30-100 m wide quartz dyke along the main fault, surrounded by sheared basement rocks. Within a zone of >10 m metasomatism transformed the wall rocks to mostly kaolinite, chlorite and phyllosilicates. The quartz dyke exhibits a layered to lenticular and partly symmetric structure with different types of quartz masses, transected by a complex quartz vein network. This already indicates pulses of fluid flux and fragmentation during the lifetime of the shear zone. Analyses by optical microscopy, cathodoluminescence (CL) and SEM-EDX reveal at least four subsequent stages of quartz crystallization and fragmentation. (i) The oldest generation of quartz is represented by a homogeneous dark grey to reddish quartz mass made up by ~10-20 μm-sized crystals. It contains mm- to cm-sized angular wall-rock fragments, completely altered to kaolinite, indicating intense wall-rock alteration prior to the earliest event of silica precipitation. This rules out the possibility that the quartz mass developed from silicification of the wall rocks. This first type of quartz occurs as cm- to dm-large angular fragments in (ii) a light grey to pink quartz mass formed by ~10-50 μm-sized crystals. The different colours result from variable types and amounts of inclusions. Quartz of both generations shows random crystallographic orientations and complex inclusion structures. It probably developed during two fragmentation events and possibly from a silica gel precursor that crystallized after precipitation. (iii) The third quartz generation formed as a set of mm- to dm-wide veins roughly parallel to the trend of the Pfahl zone

  3. Determination of the Components of the Gyration Tensor of Quartz by Oblique Incidence Transmission Two-Modulator Generalized Ellipsometry

    Energy Technology Data Exchange (ETDEWEB)

    Arteaga, O. [Universitat de Barcelona; Canillas, A. [Universitat de Barcelona; Jellison Jr, Gerald Earle [ORNL

    2009-01-01

    The two independent components of the gyration tensor of quartz, g{sub 11} and g{sub 33}, have been spectroscopically measured using a transmission two-modulator generalized ellipsometer. The method is used to determine the optical activity in crystals in directions other than the optic axis, where the linear birefringence is much larger than the optical activity.

  4. Quartz: structural and thermodynamic analyses across the α ↔ β transition with origin of negative thermal expansion (NTE) in β quartz and calcite.

    Science.gov (United States)

    Antao, Sytle M

    2016-04-01

    The temperature variation, T, of the crystal structure of quartz, SiO2, from 298 to 1235 K was obtained with synchrotron powder X-ray diffraction data and Rietveld structure refinements. The polymorphic transformation from P3221 (low-T, α quartz) to P6222 (high-T, β quartz) occurs at a transition temperature, Ttr = 847 K. The T variations of spontaneous strains and several structural parameters are fitted to an order parameter, Q, using Landau theory. The change in Si atom coordinate, Six, gives Ttr - Tc = 0.49 K, which indicates an α ↔ β transition that is weakly first order and nearly tricritical in character (Q(4) ∝ T). Strains give higher Ttr - Tc values (≃ 7 K). Other fitted parameters are the oxygen Oz coordinate, Si-Si distance, Si-O-Si and ϕ angles, and intensity of the (111) reflection, I111. In α quartz, the Si-Si distance increases with T because of cation repulsion, so the Si-O-Si angle increases (and ϕ decreases) and causes the thermal expansion of the framework structure that consists of corner-sharing distorted rigid SiO4 tetrahedra. The Si-Si distances contract with T and cause negative thermal expansion (NTE) in β quartz because of increasing thermal librations of the O atom in the Si-O-Si linkage that occur nearly perpendicular to the Si-Si contraction. In calcite, CaCO3, the short Ca-Ca distance expands with T, but the next-nearest Ca-Ca distance, which is of equal length to the a axis, contracts with T and causes NTE along the a axis. The thermal librations of the atoms in the rigid CO3 group increase with T along the c axis.

  5. Adsorption calorimetry during metal vapor deposition on single crystal surfaces: Increased flux, reduced optical radiation, and real-time flux and reflectivity measurements

    Science.gov (United States)

    Sellers, Jason R. V.; James, Trevor E.; Hemmingson, Stephanie L.; Farmer, Jason A.; Campbell, Charles T.

    2013-12-01

    Thin films of metals and other materials are often grown by physical vapor deposition. To understand such processes, it is desirable to measure the adsorption energy of the deposited species as the film grows, especially when grown on single crystal substrates where the structure of the adsorbed species, evolving interface, and thin film are more homogeneous and well-defined in structure. Our group previously described in this journal an adsorption calorimeter capable of such measurements on single-crystal surfaces under the clean conditions of ultrahigh vacuum [J. T. Stuckless, N. A. Frei, and C. T. Campbell, Rev. Sci. Instrum. 69, 2427 (1998)]. Here we describe several improvements to that original design that allow for heat measurements with ˜18-fold smaller standard deviation, greater absolute accuracy in energy calibration, and, most importantly, measurements of the adsorption of lower vapor-pressure materials which would have previously been impossible. These improvements are accomplished by: (1) using an electron beam evaporator instead of a Knudsen cell to generate the metal vapor at the source of the pulsed atomic beam, (2) changing the atomic beam design to decrease the relative amount of optical radiation that accompanies evaporation, (3) adding an off-axis quartz crystal microbalance for real-time measurement of the flux of the atomic beam during calorimetry experiments, and (4) adding capabilities for in situ relative diffuse optical reflectivity determinations (necessary for heat signal calibration). These improvements are not limited to adsorption calorimetry during metal deposition, but also could be applied to better study film growth of other elements and even molecular adsorbates.

  6. Millimeter And Submillimeter-Wave Integrated Circuits On Quartz

    Science.gov (United States)

    Mehdi, Imran; Mazed, Mohammad; Siegel, Peter; Smith, R. Peter

    1995-01-01

    Proposed Quartz substrate Upside-down Integrated Device (QUID) relies on UV-curable adhesive to bond semiconductor with quartz. Integrated circuits including planar GaAs Schottky diodes and passive circuit elements (such as bandpass filters) fabricated on quartz substrates. Circuits designed to operate as mixers in waveguide circuit at millimeter and submillimeter wavelengths. Integrated circuits mechanically more robust, larger, and easier to handle than planar Schottky diode chips. Quartz substrate more suitable for waveguide circuits than GaAs substrate.

  7. Atomic force microscopy of atomic-scale ledges and etch pits formed during dissolution of quartz

    Science.gov (United States)

    Gratz, A. J.; Manne, S.; Hansma, P. K.

    1991-01-01

    The processes involved in the dissolution and growth of crystals are closely related. Atomic force microscopy (AFM) of faceted pits (called negative crystals) formed during quartz dissolution reveals subtle details of these underlying physical mechanisms for silicates. In imaging these surfaces, the AFM detected ledges less than 1 nm high that were spaced 10 to 90 nm apart. A dislocation pit, invisible to optical and scanning electron microscopy measurements and serving as a ledge source, was also imaged. These observations confirm the applicability of ledge-motion models to dissolution and growth of silicates; coupled with measurements of dissolution rate on facets, these methods provide a powerful tool for probing mineral surface kinetics.

  8. OH defects in quartz in granitic systems doped with spodumene, tourmaline and/or apatite: experimental investigations at 5-20 kbar

    Science.gov (United States)

    Frigo, C.; Stalder, R.; Hauzenberger, C. A.

    2016-07-01

    The incorporation of OH defects in quartz as a function of Li content in the bulk system and pressures was investigated. Quartz crystals were grown in water-saturated granitic systems, containing various amounts Li, B and P, supplied as accessory phases such as spodumene, tourmaline or apatite in the starting mixtures. High pressure experiments were performed at temperatures between 900 and 1100 °C, and pressures between 5 and 20 kbar with a piston cylinder apparatus, and the synthesized quartz crystals were analyzed by IR spectroscopy, electron microprobe and LA-ICP-MS spectroscopy. All IR absorption spectra revealed absorption features that can be assigned to AlOH (3313, 3379 and 3431 cm-1) and (4H)Si defects (3585 cm-1), whereas quartz grown in the Li and B systems exhibited two additional bands related, respectively, to LiOH (3483 cm-1) and BOH defects (3596 cm-1). It was further observed that LiOH incorporation increases with higher spodumene content in the starting material and decreases with pressure, until no LiOH defects are observed at pressure higher than 15 kbar. Specifically, the most pronounced reduction of LiOH defects occurs in a rather narrow pressure interval (10-15 kbar) close to the high-quartz/low-quartz transition. However, the link between the transition and the defect incorporation remains unclear. Li total concentrations always exceed the Li-coupled LiOH defects, suggesting the simultaneous presence of dry AlLi defects. Results of this study suggest that LiOH defects are detectable only in quartz crystals grown from middle and upper crustal sections (such as hydrothermal quartz) and not in quartz from deep roots of orogenic granitoids.

  9. SEM-Cathodoluminescence and fluid inclusion study of quartz veins in Hugo Dummett porphyry Cu-Au deposit,South Mongolia

    Science.gov (United States)

    Sanjaa, M.; Fujimaki, H.; Ken-Ichiro, H.

    2010-12-01

    The Hugo Dummett porphyry copper-gold deposit in Oyu Tolgoi, South Mongolia is a high-sulfidation type deposit which consists of Cu-Au bearing quartz veins. Cathodoluminescence (CL) analysis using scanning electron microscope (SEM) and fluid inclusion microthermometer were performed to elucidate the relationship between CL structures, fluid inclusion microthermometer of different quartz generations, and ore forming process of the Hugo Dummett deposit. Hydrothermal quartz from quartz-sulfide veins in the porphyry Cu-Au deposit in Hugo Dummett, revealing the following textures: (1) euhedral growth zones (2) embayed and rounded CL-bright cores, with CL-dark and CL-gray overgrowths, (3) concentric and non concentric growth zones, and (4) CL dark/bright microfractures. These textures indicate that many veins have undergone fracturing, growth of quartz into fluid-filled space and quartz dissolution of quartz. SEM-CL imaging indicates vein quartz in the Hugo Dummett deposit, initially grew as individual CL-bright crystals 356 ± 10°C liquid-reservoir (average Th value for fluid inclusions in the crystal cores is 359°C). In contract, SEM-CL imaging shows the edges of the micron-scale growth zones of varying CL intensity, reflecting quartz precipitation at some later time, when the Hugo Dummett deposit hydrothermal system had cooled, when reservoir conditions were about 211 ± 25°C (average Th value of 212°C). Crystal growth is SEM-CL evidence of the vein quartz having been partly dissolved. Pressure change has a large effect on quartz solubility and may have been responsible for quartz dissolution and precipitation textures in the cooling hydrothermal system. CL-dark microfractures homogenization temperatures lower 169 ± 16°C (average Th value 170°C) than CL bright and CL gray. Temperature and pressure of the mineralized fluid estimates a pressure of formation of 0.3-0.5 kbar (lithostatic), was formed at approximately 2 km depth, as well as a formation temperature

  10. Emission polarization study on quartz and calcite.

    Science.gov (United States)

    Vincent, R. K.

    1972-01-01

    Calculation of the spectral emission polarization of quartz and calcite polished plates for observation angles of 20 and 70 deg by the substitution of complex index of refraction values for each mineral into Fresnel's equations. The emission polarization is shown to be quite wavelength-dependent, demonstrating that selected narrow or medium-width spectral bands exhibit a significantly higher percentage of polarization than a broad spectral band for these two minerals. Field measurements with a broadband infrared radiometer yield polarizations on the order of 2% for a coarse-grained granite rock and beach sand (both quartz-rich). This implies that a more sensitive detector with a selected medium-width filter may be capable of measuring emission polarization accurately enough to make this parameter useful as a remote sensing tool for discrimination among rocks on the basis of texture.

  11. The CMS forward calorimeter with quartz fibres

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    Part of the forward hadron calorimeter for the CMS experiment at the LHC is seen here. The calorimeter will be placed at the ends of the experiment barrel to measure the energy of particles produced in the 14 TeV proton-proton collisions. In consists of an iron absorber and specially designed radiation-hard quartz so that it survives the high radiation levels produced by collisions.

  12. THE FRICTION OF QUARTZ IN HIGH VACUUM

    Science.gov (United States)

    the effects of surface cleanliness . Ultra-high vacuums (to 10 to the minus 10th power torr) and high temperatures (to 350 deg C) were combined with...chemical cleaning and careful handling techniques to produce the maximum surface cleanliness . The coefficient of static friction under varying...on 30-40 mesh glass balls. The coefficient of friction of smooth quartz was found to vary from 0.1 to 1.0 depending on the surface cleanliness . The

  13. Ammonia sorption by Dawson acid studied by IR spectroscopy and microbalance

    Science.gov (United States)

    Micek-Ilnicka, A.; Gil, B.; Lalik, E.

    2005-04-01

    Using in-situ microbalance and infrared spectroscopy techniques the double ammonia proton complexation was traced. The results confirm the formation of N 2H 7+ dimer in solid Dawson acid H 6P 2W 18O 62, previously reported only for N 2H 7I and for (N 2H 7) 4SiW 12O 40. The formation of such dimers was evidenced by the microbalance results, the molar ratio of ammonia to proton was measured as 2:1 at 10.7 kPa and 298 K. The formation of NH 4+ monomer (band at 1410 cm -1) and N 2H 7+ dimer (1460 cm -1) was revealed by IR spectroscopy. Enthalpy of ammonia sorption on Dawson structure was calculated to be -127.9 kJ mol -1, indicating the lower acid strength of Dawson-type compared to that of the Keggin-type heteropolyacids, like H 4SiW 12O 40.

  14. Chirality-asymmetry force between α-quartz and copper block

    Institute of Scientific and Technical Information of China (English)

    Hu Yong-Hong; Xu Qing; Liu Zhong-Zhu

    2009-01-01

    The chirality-asymmetry macroscopic force mediated by light pseudoscalar particles between α-quartz and some achiral matter is studied.If this force between achiral source mass and α-quartz with some chirality is attractive,it will become repulsive when the chirality of the α-quartz crystal is changed.According to the tested limits of the coupling constant gsgp/hc<1.5×10-24 at the Compton wavelength)λ=10-3 m,the force(F)between a 0.08×0.08×0.002 m3 block of α-quartz and a 0.08×0.08×0.01 m3 copper block with a separation being 0.5×10-3 m in between.is estimated from the published data at less than 4.64×10-24 N.i.e.F<4.64×10-24 N.

  15. Exposure vs toxicity levels of airborne quartz, metal and carbon particles in cast iron foundries.

    Science.gov (United States)

    Moroni, Beatrice; Viti, Cecilia; Cappelletti, David

    2014-01-01

    Aerosol dust samples and quartz raw materials from different working stations in foundry plants were characterized in order to assess the health risk in this working environment. Samples were analysed by scanning and transmission electron microscopy coupled with image analysis and microanalysis, and by cathodoluminescence spectroscopy. In addition, the concentration and the solubility degree of Fe and other metals of potential health effect (Mn, Zn and Pb) in the bulk samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). Overall, the results indicate substantial changes in quartz crystal structure and texture when passing from the raw material to the airborne dust, which include lattice defects, non-bridging oxygen hole centres and contamination of quartz grains by metal and/or graphite particles. All these aspects point towards the relevance of surface properties on reactivity. Exposure doses have been estimated based on surface area, and compared with threshold levels resulting from toxicology. The possible synergistic effects of concomitant exposure to inhalable magnetite, quartz and/or graphite particles in the same working environment have been properly remarked.

  16. A Z-axis Quartz Cross-fork Micromachined Gyroscope Based on Shear Stress Detection

    Directory of Open Access Journals (Sweden)

    Peitao Dong

    2010-03-01

    Full Text Available Here we propose a novel quartz micromachined gyroscope. The sensor has a simple cross-fork structure in the x-y plane of quartz crystal. Shear stress rather than normal stress is utilized to sense Coriolis’ force generated by the input angular rate signal. Compared to traditional quartz gyroscopes, which have two separate sense electrodes on each sidewall, there is only one electrode on each sidewall of the sense beam. As a result, the fabrication of the electrodes is simplified and the structure can be easily miniaturized. In order to increase sensitivity, a pair of proof masses is attached to the ends of the drive beam, and the sense beam has a tapered design. The structure is etched from a z-cut quartz wafer and the electrodes are realized by direct evaporation using the aperture mask method. The drive mode frequency of the prototype is 13.38 kHz, and the quality factor is approximately 1,000 in air. Therefore, the gyroscope can work properly without a vacuum package. The measurement ability of the shear stress detection design scheme is validated by the Coriolis’ force test. The performance of the sensor is characterized on a precision rate table using a specially designed readout circuit. The experimentally obtained scale factor is 1.45 mV/°/s and the nonlinearity is 3.6% in range of ±200 °/s.

  17. Effects of pressure and temperature on the thermal properties of a salt and a quartz monzonite

    Energy Technology Data Exchange (ETDEWEB)

    Durham, W.B.; Abey, A.E.

    1981-03-27

    Measurements have been made of thermal conductivity, diffusivity, and linear expansion as a function of temperature (to 573 K) and hydrostatic pressure (to 50 MPa) on two rocks, Avery Island domal salt and Climax Stock quartz monzonite. For Avery Island salt the thermal properties do not show any pressure dependence and are approximately the same values as for single crystal halite at 0.1 MPa. The lack of pressure dependence is attributed to the high symmetry of halite (cubic) and to its low strength, both of which inhibit brittle fracturing. For Climax Stock quartz monzonite no pressure dependence of thermal diffusivity has been resolved, but conductivity does show a drop of approximately 10% with decreasing pressure from 50 to 3 MPa. The pressure dependence is not measurably altered by heating the rock to as high as 473 K under 50 MPa. Our measurements so far on the thermal conductivity of quartz monzonite vs temperature and pressure are in agreement with predictions of the Walsh and Decker (1966) model of thermal conductivity vs crack porosity based on independent measurements of crack porosity vs temperature and pressure for the same quartz monzonite. Heating to temperatures greater than 473 K at 50 MPa, or heating to lower temperatures at lower pressures, should substantially reduce thermal conductivity of the quart monzonite.

  18. Diaplectic Glass Content in Experimentally Shock-loaded Quartz Determined by X-Ray Powder Diffraction

    Science.gov (United States)

    Skala, R.; Hoerz, F.; Langenhorst, F.

    2003-01-01

    Quartz is the most common mineral of terrestrial crustal rocks and thus a widespread indicator for impact cratering and associated shock metamorphism. Planar deformation features (PDFs) are among the most prominent and diagnostic shock features in quartz and they represent thin lamellae of glass that formed via solid-state transformations. This socalled 'diaplectic' glass becomes pervasive at higher pressures and results in optically isotropic and X-ray-amorphous phases that resemble texturally the original quartz grains (without evidence of melt flow). In the past, it has been shown that the amount of this amorphous material in experimentally shock-loaded quartz correlates with peak shock pressure. Both reports derive the glass content from density measurements of individual crystals employing the equation X(%) = (rho(sub x) - rho(sub 0))/(rho(sub x) - rho(sub gl)), where x and 0 stands for X-ray and average (optical) density, respectively. The density of glass, rho(sub gl), was adopted as 2.2 g/cu cm. Though the same procedures had been applied, the resulting glass content differs significantly among the above studies. In the present study, we are using a new approach based solely on the integral intensity of a single, carefully selected reflection in the XRD pattern, and we will compare our data to those reported in the literature.

  19. Luminescence sensitivity changes in quartz as a result of annealing

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Agersnap Larsen, N.; Mejdahl, V.

    1995-01-01

    Retrospective dosimetry using optically stimulated luminescence (OSL) on quartz extracted from (for example) bricks needs to account for strong OSL sensitivity changes that are known to occur depending on the previous thermal treatment of the sample. Non-heated quartz exhibits OSL orders of magni......Retrospective dosimetry using optically stimulated luminescence (OSL) on quartz extracted from (for example) bricks needs to account for strong OSL sensitivity changes that are known to occur depending on the previous thermal treatment of the sample. Non-heated quartz exhibits OSL orders...... of magnitude less per unit radiation than that for heated material. The reason these temperature-induced sensitivity changes occur in quartz is presently not well understood. This phenomenon is also seen in the related area of luminescence dating in which sedimentary quartz and quartz from heated...

  20. Effects of citric acid on separation of sillimanite from quartz

    Institute of Scientific and Technical Information of China (English)

    李晔; 雷东升; 鲁巍; 许时

    2002-01-01

    Quartz is the main gangue mineral of sillimanite. The results show that Al3+ and Fe3+ ion can activate the floatation of quartz and make the separation of quartz and sillimanite difficult when anion collector is used, and citric acid can inhibit the quartz activated by metallic ion and have slight influence on the sillimanite. X-ray photoelectronic energy spectrum analysis indicates that there are obvious electronic energy peaks on the surface of the quartz before citric acid is added into the ore pulp in presence of Al3+ and Fe3+, and after citric acid is added, the energy peak vanished. So citric acid can make Al3+ and Fe3+ on the surface of quartz solve and decrease the active points on the surface of quartz which can adsorb anion collector.

  1. 石英微机械陀螺的研究进展%Reaearch Development of Quartz Micromachined Gyroscopes

    Institute of Scientific and Technical Information of China (English)

    关冉; 张卫平; 陈文元; 张弓; 成宇翔

    2012-01-01

    首先介绍了石英微机械陀螺基于压电效应和科氏加速度的工作原理,回顾了石英微机械陀螺的发展历程,并且介绍了石英微机械陀螺的国内外发展现状.然后,针对石英微机械陀螺不同的结构进行了分类,并且对于不同结构的石英微机械陀螺的具体加工工艺、性能参数、应用领域等进行了综述.最后,对不同结构类型的石英微机械陀螺的尺寸、加工工艺,检测轴向,精度等参数进行了总结和对比,在此基础上分析了石英微机械陀螺的发展趋势,并指出了石英微机械陀螺研究中存在的问题,例如石英加工过程中产生的侧壁晶棱的不平整、石英侧壁电极的制作困难以及石英微机械陀螺多轴化应用的限制等.%Firstly, the working principle of the quartz micromachined gyroscope is introduced, which is based on the piezoelectric effect and the Coriolis acceleration, the development history of the quartz micromachined gyroscope is reviewed, and the development present situation of the quartz micromachined gyroscope is introduced both domestically and abroad. Then, the quartz micromachined gyroscope is classified into several types according to its different structures, and the specific fabrication process, performance parameter and application fields of the quartz micromachined gyroscope for the different structures are reviewed. Finally, the parameters of the quartz micromachined gyroscope for the different kinds of structures are summarized and compared, including the size, fabrication process, detection axis and accuracy, and on that basis, the development trends of the quartz micromachined gyroscope are analyzed, and the problems that limit the development of quartz micromachined gyroscope are pointed out, including the uneven crystal edges of the quartz sidewall caused by the fabrication process, the difficulties of electrode fabrication on the quartz sidewall and the limitation of the multi

  2. A study on the electrochemical behaviour of polypyrrole films in concentrated aqueous alkali halide electrolytes

    DEFF Research Database (Denmark)

    Jafeen, M. J. M.; Careem, M.A.; Skaarup, Steen

    2014-01-01

    deposited on gold-coated quartz crystals by electropolymerization and simultaneous cyclic voltammetry and electrochemical quartz crystal microbalance techniques were used. During the first redox cycle, while large water movement is observed along with the counter ions in dilute electrolytes, such water...

  3. Characterization of anionic-exchange membranes for direct alcohol alkaline fuel cells

    CSIR Research Space (South Africa)

    Abuin, GC

    2009-06-01

    Full Text Available and Young modulus were evaluated and compared to other membrane materials commonly employed in PEM fuel cells. A quartz crystal microbalance (QMC) was used to measure the water uptake of thin membranes of this material casted over the quartz crystals...

  4. Laser ultrasonic analysis of normal modes generated by a voltage pulse on an AT quartz sensor.

    Science.gov (United States)

    Goossens, Jozefien; Martinez, Loïc; Glorieux, Christ; Wilkie-Chancellier, Nicolas; Ehssein, Chighali Ould; Serfaty, Stéphane

    2006-12-22

    Laser ultrasonic detection is a versatile and highly sensitive tool for the observation of surface waves. In the following study, laser ultrasonic detection is used for the experimental study of spurious normal vibration modes of a disk quartz sensor excited by a voltage pulse. The AT cut crystal (cut of the crystal relative to the the main crystallographic axis is 35.25 degrees) is optimal for generating mainly thickness-shear vibrations (central frequency 6 MHz) on the quartz surface. However, resulting from shear-to-longitudinal and shear-to-surface mode conversion, and from the weak coupling with the other crystallographic axes, other modes (thickness-compressional and bending modes) are always present in the plate response. Since the laser vibrometer is sensitive to normal displacements, the laser investigation shows waves that can be considered as unwanted for the AT quartz used as a shear sensor. The scanned three dimensional (3D) amplitude-space-time signals are carefully analysed using their representation in three dual Fourier domains (space-time, wave number-frequency). Results on the transient analysis of the waves, the normal bending modes and the dispersion curves are shown.

  5. Optical properties and thermal stability of germanium oxide (GeO{sub 2}) nanocrystals with {alpha}-quartz structure

    Energy Technology Data Exchange (ETDEWEB)

    Ramana, C.V., E-mail: rvchintalapalle@utep.edu [Department of Mechanical Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Department of Materials Science and Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Carbajal-Franco, G. [Department of Materials Science and Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Vemuri, R.S. [Department of Mechanical Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Department of Materials Science and Engineering, University of Texas at El Paso, El Paso, TX 79968 (United States); Troitskaia, I.B. [Laboratory of Optical Materials and Structures, Institute of Semiconductor, Physics SB RAS, Novosibirsk 630090 (Russian Federation); Gromilov, S.A. [Laboratory of Crystal Chemistry, Institute of Inorganic Chemistry, SB RAS, Novosibirsk 630090 (Russian Federation); Atuchin, V.V. [Laboratory of Optical Materials and Structures, Institute of Semiconductor, Physics SB RAS, Novosibirsk 630090 (Russian Federation)

    2010-10-25

    Germanium dioxide (GeO{sub 2}) crystals were prepared by a chemical precipitation method at a relatively low-temperature (100 {sup o}C). The grown crystals were characterized by studying their microstructure, optical properties and thermal stability. The results indicate that the grown GeO{sub 2} crystals exhibit {alpha}-quartz type crystal structure. The lattice parameters obtained from XRD were a = 4.987(4) A and c = 5.652(5) A. Electron microscopy analysis indicates a high structural quality of GeO{sub 2} crystals grown using the present approach. Optical absorption measurements indicate a direct bandgap of 5.72 eV without any additional bands arising from localized or defect states. Thermogravimetric measurements indicate the temperature stability of the grown GeO{sub 2} nanocrystals. Microscopic analysis coupled with energy dispersive X-ray spectroscopy of the GeO{sub 2} crystals with {alpha}-quartz type crystal structure indicates their stability in chemical composition up to a temperature of 400 deg. C. The surface morphology of GeO{sub 2} crystals, however, found to be changing with the increase in temperature.

  6. Brittle-viscous deformation of vein quartz under fluid-rich low greenschist facies conditions

    Science.gov (United States)

    Jørgen Kjøll, Hans; Viola, Giulio; Menegon, Luca; Sørensen, Bjørn

    2015-04-01

    A coarse grained, statically crystallized quartz vein with a random CPO, embedded in a phyllonitic matrix, was studied by optical microscopy, SEM imaging and EBSD to gain insights into the processes of strain localization in quartz deformed under low greenschist facies conditions at the frictional-viscous transition. The vein is located in a high strain zone at the front of an imbricate stack of Caledonian age along the northwesternmost edge of the Repparfjord Tectonic Window in northern Norway. The vein was deformed within the Nussirjavrri Fault Zone (NFZ), an out-of-sequence thrust with a phyllonitic core characterized by a ramp-flat-ramp geometry, NNW plunging stretching lineations and top-to-the SSE thrusting kinematics. Deformation conditions are typical of the frictional-viscous transition. The phyllonitic core formed at the expense of metabasalt wherein feldspar broke down to form interconnected layers of fine, synkinematic phyllosilicates. In the mechanically weak framework of the phyllonite, the studied quartz vein acted as a relatively rigid body deforming mainly by coaxial strain. Viscous deformation, related to the development of a mesoscopic pervasive extensional crenulation cleavage, was accommodated within the vein initially by basal slip of suitably oriented quartz crystals, which produced e.g. undulose extinction, extinction bands and bulging grain boundaries. In the case of misoriented quartz crystals, however, glide-accommodated dislocation creep resulted soon inefficient and led to localized dislocation tangling and strain hardening. In response to 1) hardening, 2) progressive increase of fluid pressure within the actively deforming vein and 3) increasing competence contrast between the vein and the surrounding weak, foliated phyllonitic fault core, quartz crystals began to deform frictionally along specific lattice planes oriented optimally with respect to the imposed stress field. Microfaulting generated small volumes of gouge along

  7. AEROSOL FILTRATION USING QUARTZ SAND FILTER

    Directory of Open Access Journals (Sweden)

    Abbas H. Sulaymon

    2012-01-01

    Full Text Available The cement industry is the major source of cement dust which contains heavy metals like nickel, cobalt, lead, chromium, arsenic and hazardous substances like dioxins and furans. Exposure to these substances can cause health problems to human, animals and vegetation. A continuous pilot scale quartz sand filter was constructed and uses to study the effect of important design parameters (temperature, pre-loaded dust on the collector, diameter of the filter, bed depth, collector size and superficial velocity on its performance for cleaning of cement dust from air. Initial penetration and initial pressure drop (after 180s were measured and compared for different variables used in this study. The dirty bed was cleaned by means of reverse air flow when the pressure drop across the filter rises to 20 cmH2O. A macroscopic model describes the filter clogging was used to predict the effluent histories based on initial collection efficiency (η0exp which was determined from experimental data. A removal efficiency of more than 99% was obtained. The results show that 0.4% of cement dust still adheres on the quartz sand bed after 5 min of cleaning cycle. The presence of 0.4% of pre-load dust on the quartz sand filter enhanced the efficiency and low initial penetration, moderate initial pressure drop was obtained. At given Empty Bed Contact Time (EBCT, with different filter diameters 30 and 15 cm, a sharp decrease in initial penetration from 0.41-0.03 was obtained respectively. A nonlinear relationship between penetration and temperature was found. The initial penetration can be reduced by using smaller filter diameter, small collector size and collector with pre-load dust with 0.4%. The experiment that operates at a filter diameter of 15 cm and temperature of 25°C represent the minimum penetration among all the experiments.

  8. Kinetics of the coesite to quartz transformation

    Science.gov (United States)

    Mosenfelder, J.L.; Bohlen, S.R.

    1997-01-01

    The survival of coesite in ultrahigh-pressure (UHP) rocks has important implications for the exhumation of subducted crustal rocks. We have conducted experiments to study the mechanism and rate of the coesite ??? quartz transformation using polycrystalline coesite aggregates, fabricated by devitrifying silica glass cylinders containing 2850H/106 Si at 1000??C and 3.6 GPa for 24h. Conditions were adjusted following synthesis to transform the samples at 700-1000??C at pressures 190-410 MPa below the quartz-coesite equilibrium boundary. Reaction proceeds via grain-boundary nucleation and interface-controlled growth, with characteristic reaction textures remarkably similar to those seen in natural UHP rocks. We infer that the experimental reaction mechanism is identical to that in nature, a prerequisite for reliable extrapolation of the rate data. Growth rates obtained by direct measurement differ by up to two orders of magnitude from those estimated by fitting a rate equation to the transformation-time data. Fitting the rates to Turnbull's equation for growth therefore yields two distinct sets of parameters with similar activation energies (242 or 269 kJ/mol) but significantly different pre-exponential constants. Extrapolation based on either set of growth rates suggests that coesite should not be preserved on geologic time scales if it reaches the quartz stability field at temperatures above 375-400??C. The survival of coesite has previously been linked to its inclusion in strong phases, such as garnet, that can sustain a high internal pressure during decompression. Other factors that may play a crucial role in preservation are low fluid availability - possibly even less than that of our nominally "dry" experiments - and the development of transformation stress, which inhibits nucleation and growth. These issues are discussed in the context of our experiments as well as recent observations from natural rocks. ?? 1997 Elsevier Science B.V.

  9. Metasomatic origin of quartz-pyroxene rock, Akilia, Greenland, and implications for Earth's earliest life.

    Science.gov (United States)

    Fedo, Christopher M; Whitehouse, Martin J

    2002-05-24

    A quartz-pyroxene rock interpreted as a banded iron formation (BIF) from the island of Akilia, southwest Greenland, contains (13)C-depleted graphite that has been claimed as evidence for the oldest (>3850 million years ago) life on Earth. Field relationships on Akilia document multiple intense deformation events that have resulted in parallel transposition of Early Archean rocks and significant boudinage, the tails of which commonly form the banding in the quartz-pyroxene rock. Geochemical data possess distinct characteristics consistent with an ultramafic igneous, not BIF, protolith for this lithology and the adjacent schists. Later metasomatic silica and iron introduction have merely resulted in a rock that superficially resembles a BIF. An ultramafic igneous origin invalidates claims that the carbon isotopic composition of graphite inclusions represents evidence for life at the time of crystallization.

  10. High-quality Crystal Filter – Design and Realization

    Directory of Open Access Journals (Sweden)

    D. M. Dujković

    2013-11-01

    Full Text Available Analog oscillators and filters are still very important devices in modern telecommunication and measurement equipment. Quartz crystal units are used for high-quality oscillators and filters, due to their extremely stable resonant frequency and Q-factor. In this paper the design and realization of a high-quality bandpass quartz crystal filter with a possible application to antenna circuitry is described.

  11. Calorimetric thermobarometry of experimentally shocked quartz

    Science.gov (United States)

    Ocker, Katherine D.; Gooding, James L.; Hoerz, Friedrich

    1994-01-01

    Structural damage in experimentally shock-metamorphosed, granular quartz is quantitatively measurable by differential scanning calorimetry (DSC). Shock-induced loss of crystallinity is witnessed by disappearance of the alpha/beta phase transformation and evolution of a broad endoenthalpic strain peak at 650-900 K. The strain-energy peak grows rapidly at less than 10 GPa but declines with increasing shock pressure; it approaches zero at 32 GPa where vitrification is extensive. Effects of grain size and post-shock thermal history must be better understood before calorimetric thermobarometry of naturally shocked samples becomes possible.

  12. Note: A miniature oscillating microbalance for sampling ice and volcanic ash from a small airborne platform.

    Science.gov (United States)

    Airey, M W; Harrison, R G; Nicoll, K A; Williams, P D; Marlton, G J

    2017-08-01

    A lightweight and low power oscillating microbalance for in situ sampling of atmospheric ice and volcanic ash is described for airborne platforms. Using a freely exposed collecting wire fixed at only one end to a piezo transducer, the instrument collects airborne materials. Accumulated mass is determined from the change in natural frequency of the wire. The piezo transducer is used in a dual mode to both drive and detect the oscillation. Three independent frequency measurement techniques are implemented with an on-board microcontroller: a frequency sweep, a Fourier spectral method, and a phase-locked loop. These showed agreement to ±0.3 Hz for a 0.5 mm diameter collecting wire of 120 mm long, flown to 19 km altitude on a weather balloon. The instrument is well suited to disposable use with meteorological radiosondes, to provide high resolution vertical profiles of mass concentration.

  13. Note: A miniature oscillating microbalance for sampling ice and volcanic ash from a small airborne platform

    Science.gov (United States)

    Airey, M. W.; Harrison, R. G.; Nicoll, K. A.; Williams, P. D.; Marlton, G. J.

    2017-08-01

    A lightweight and low power oscillating microbalance for in situ sampling of atmospheric ice and volcanic ash is described for airborne platforms. Using a freely exposed collecting wire fixed at only one end to a piezo transducer, the instrument collects airborne materials. Accumulated mass is determined from the change in natural frequency of the wire. The piezo transducer is used in a dual mode to both drive and detect the oscillation. Three independent frequency measurement techniques are implemented with an on-board microcontroller: a frequency sweep, a Fourier spectral method, and a phase-locked loop. These showed agreement to ±0.3 Hz for a 0.5 mm diameter collecting wire of 120 mm long, flown to 19 km altitude on a weather balloon. The instrument is well suited to disposable use with meteorological radiosondes, to provide high resolution vertical profiles of mass concentration.

  14. Comparison of thermoluminescence (TL) and cathodoluminescence (ESEM-CL) properties between hydrothermal and metamorphic quartzes

    Energy Technology Data Exchange (ETDEWEB)

    Topaksu, M., E-mail: mtopaksu@adiyaman.edu.tr [Department of Physics, Faculty of Science and Art, Adiyaman University, 02040 Adiyaman (Turkey); Correcher, V. [CIEMAT, Av. Complutense 22, Madrid 28040 (Spain); Garcia-Guinea, J. [CSIC, Museo Nacional de Ciencias Naturales, C/Jose Gutierrez Abascal 2, Madrid 28006 (Spain); Topak, Y. [Adiyaman University, Vocational High School, 02040 Adiyaman (Turkey); Goeksu, H.Y. [Department of Physics, Faculty of Science and Art, Adiyaman University, 02040 Adiyaman (Turkey)

    2012-06-15

    This paper reports on the Thermoluminescence (TL) and Cathodoluminescence (CL) emission of well-characterized hydrothermal milky quartz specimens from Hakkari in Turkey, labeled THQ, and Madrid in Spain, labeled SHQ, and metamorphic quartz from Madrid, in Spain, labeled SMQ. Both hydrothermal and metamorphic quartz samples display similar UV-IR CL spectra consisting of five groups of components centered at 330 nm and 380 nm linked to [AlO{sub 4}] Degree-Sign centers, 420 nm due to intrinsic defects such as oxygen vacancies, lattice defects, and impurities which modify the crystal structure, 480 nm associated with [AlO{sub 4}] Degree-Sign centers of substitutional Al{sup 3+}, and a red broad band related to the hydroxyl defects in the quartz lattice as precursors of non-bridging oxygen hole centers (NBOHC) and substitutional point defects. The Turkish quartz specimen exhibits higher CL intensity in the UV region (up to 330 nm) than the Spanish specimens probably linked to the presence of Ca (0.95% in THQ and less than 0.1% in SHQ and SMQ). At wavelengths greater than 330 nm, SMQ (formed at high pressure 6000 bars and temperatures over 500-600 Degree-Sign C) shows higher intensity than the hydrothermal (growth at 2000 bars and temperatures 200-300 Degree-Sign C) samples associated with the formation process. The natural blue TL glow curves of both THQ and SHQ display a weaker TL intensity than the SMQ, attributable to the Al (0.32%), Ti (0.14%), K (0.01%) and Zr (76 ppm) content. It is shown that mineralogical formation, crystallinity index and the content of the impurities seem to be the main parameters of influence in the shape intensity of the CL and TL glow curve emission. - Highlights: Black-Right-Pointing-Pointer We reported on the TL and CL emission of well-characterized hydrothermal milky and metamorphic quartz specimens. Black-Right-Pointing-Pointer Hydrothermal and metamorphic quartz samples displayed similar UV-IR CL spectra. Black

  15. Aqueous Wetting Films on Fused Quartz.

    Science.gov (United States)

    Mazzoco; Wayner

    1999-06-15

    Using an image analyzing interferometer, IAI, the interfacial characteristics of an isothermal constrained vapor bubble, CVB, in a quartz cuvette were studied as a precursor to heat transfer research. The effects of pH and electrolyte concentration on the meniscus properties (curvature and adsorbed film thickness) and the stability of the aqueous wetting films were evaluated. The surface potential in the electric double layer was a function of the cleaning and hydroxylation of the quartz surface. The disjoining pressure isotherm for pure water was very close to that predicted by the Langmuir equation. For aqueous solutions of moderate electrolyte concentration, the Gouy-Chapman theory provided a good representation of the electrostatic effects in the film. The effect of temperature on the film properties of aqueous solutions and pure water was also evaluated: The meniscus curvature decreased with increasing temperature, while Marangoni effects, intermolecular forces, and local evaporation and condensation enhanced waves on the adsorbed film layer. Pure water wetting films were mechanically metastable, breaking into droplets and very thin films (less than 10 nm) after a few hours. Aqueous wetting films with pH 12.4 proved to be stable during a test of several months, even when subjected to temperature and mechanical perturbations. The mechanical stability of wetting films can explain the reported differences between the critical heat fluxes of pure water and aqueous solutions. The IAI-CVB technique is a simple and versatile experimental technique for studying the characteristics of interfacial systems. Copyright 1999 Academic Press.

  16. Production of quartz plates for CMS-CASTOR Experiment

    CERN Document Server

    Adiguzel, Aytul; Ayhan, Aydin; Bakirci, Mustafa Numan; Basegmez, Suzan; Beaumont, Willem; Borras, Kerstin; Campbell, Alan; De Paula Carvalho, W; Çerçi, Salim; De Jesus Damiao, Dilson; Dogangün, O; Dumanoglu, Isa; d'Enterria, David; Erchov, Y; Eskut, Eda; Figueiredo, D; Girgis, Semiray; Göttlicher, P; Gouskos, Loukas; Gurpinar, Emine; Hos, Ilknur; Katkov, Igor; Katsas, Panagiotis; Khein, Lev; Knutsson, Albert; Kuznetsov, Andrey; Lebeau, Michel; Van Mechelen, Pierre; Muhl, Carsten; Musienko, Yuri; Ochesanu, Silvia; Onengüt, G; Onengut, G Jr; Ozdemir, Kadri; Panagiotou, Apostolos; Polatoz, A; Ripert, Marion; Shileev, K; Sogut, Kenan; Tiflov, B TaliV; Kayis-Topaksu, A; Uzun, Dilber

    2008-01-01

    Light transmission rate performance of $102$ irradiated quartz samples was measured to select the best quartz plates for CMS-CASTOR calorimeter. All the produced quartz plates were originally used in a previous CERN experiment, DELPHI. Three different doses of $^{60}$Co source were used with the collaboration of PSI (Paul Scherrer Institute, Villigen PSI, Switzerland.) to study the transmission rate performance of the quartz samples after irradiation for different incident light, ranging from $250$ to $700$ nm in $5$ nm increasing steps. All samples show different decrease in the rate with wavelength for different doses. Three different steps were followed before irradiation to find out the best way of cleaning the original DELPHI Cu/Cr tracks on the samples. Results of these measurements presented here correspond to the quartz plates that will be used in one hadronic sector of CASTOR calorimeter until end of 2008. For the full calorimeter new quartz plates will be installed. We also present the light transmi...

  17. Modeling piezoelectric crystals on the Intel delta

    Energy Technology Data Exchange (ETDEWEB)

    Canfield, T.; Jones, M.; Plassmann, P.; Tang, M. [Argonne National Lab., IL (United States)

    1993-12-31

    Piezoelectric crystals are an important component in electronic appliances such as cellular phones and pagers and a critical component of almost all resonant circuits. We are particularly interested in quartz strip resonators mounted onto a surface. These crystals must resonate in a particular vibrational manding design goal, engineers would like to be able to accurately model the behavior of the crystals in a timely fashion from their disktop workstation.

  18. Acoustic Tests of Lorentz Symmetry Using Quartz Oscillators

    Directory of Open Access Journals (Sweden)

    Anthony Lo

    2016-02-01

    Full Text Available We propose and demonstrate a test of Lorentz symmetry based on new, compact, and reliable quartz oscillator technology. Violations of Lorentz invariance in the matter and photon sector of the standard model extension generate anisotropies in particles’ inertial masses and the elastic constants of solids, giving rise to measurable anisotropies in the resonance frequencies of acoustic modes in solids. A first realization of such a “phonon-sector” test of Lorentz symmetry using room-temperature stress-compensated-cut crystals yields 120 h of data at a frequency resolution of 2.4×10^{−15} and a limit of c[over ˜]_{Q}^{n}=(−1.8±2.2×10^{−14}  GeV on the most weakly constrained neutron-sector c coefficient of the standard model extension. Future experiments with cryogenic oscillators promise significant improvements in accuracy, opening up the potential for improved limits on Lorentz violation in the neutron, proton, electron, and photon sector.

  19. Fluid Inclusion Study of Quartz Xenocrysts in Mafic Dykes from Kawant Area, Chhota Udaipur District, Gujarat, India

    Directory of Open Access Journals (Sweden)

    Randive Kirtikumar

    2015-09-01

    Full Text Available Unusual mafic dykes occur in the proximity of the Ambadongar Carbonatite Complex, Lower Narmada Valley, Gujarat, India. The dykes contain dense population of quartz xenocrysts within the basaltic matrix metasomatised by carbonate-rich fluids. Plagioclase feldspars, relict pyroxenes, chlorite, barite, rutile, magnetite, Fe-Ti oxides and glass were identified in the basaltic matrix. Quartz xenocrysts occur in various shapes and sizes and form an intricate growth pattern with carbonates. The xenocrysts are fractured and contain several types of primary and secondary, single phase and two-phase fluid inclusions. The two-phase inclusions are dominated by aqueous liquid, whereas the monophase inclusions are composed of carbonic gas and the aqueous inclusions homogenize to liquid between 226°C and 361°C. Majority of the inclusions are secondary in origin and are therefore unrelated to the crystallization of quartz. Moreover, the inclusions have mixed carbonic-aqueous compositions that inhibit their direct correlation with the crustal or mantle fluids. The composition of dilute CO2-rich fluids observed in the quartz xenocrysts appear similar to those exsolved during the final stages of evolution of the Amba Dongar carbonatites. However, the carbonates are devoid of fluid inclusions and therefore their genetic relation with the quartz xenocrysts cannot be established.

  20. Development of discrete aggregates of recrystallization along micro-shear zones in quartz ribbons during multistage ductile evolution of a quartz vein

    Science.gov (United States)

    Ceccato, Alberto; Pennacchioni, Giorgio; Bestmann, Michel

    2016-04-01

    The post-magmatic ductile deformation of the Rieserferner pluton (Eastern Alps) includes localized ductile shear zones exploiting a set of joint-filling quartz veins. These deformed veins show different stages of evolution, from coarse grained vein quartz to the fine grained recrystallized aggregates of ultramylonites, locally recorded in different domains of heterogeneously sheared veins. The microstructural evolution includes, with increasing strain: (i) Development of ribbon mylonites consisting of elongated grains, oblique to the shear zone boundary, derived from different quartz veins crystals. The individual ribbons have different crystallographic orientations and aspect ratios. (ii) Dismantling of ribbons along a fracture-like network of fine grained recrystallized quartz aggregates, that commonly represent micro-shear zones (μSZ). These discrete recrystallization zones are preferentially developed in ribbons whose crystallographic axis is oriented either parallel or normal to ribbon elongation. (iii) Extensive dynamic recrystallization to fine-grained (10-20 μm) aggregates leading to quartz ultramylonites. Typically ultramylonites show a layered texture with bands having different crystallographic preferred orientation (CPO) that probably reflect the original heterogeneity in crystallographic orientations of the vein. Electron backscattered diffraction analysis indicates that the μSZ within quartz ribbons are mainly parallel to {r} or {z} planes of the host grain, and the new grain inside μSZ show a weak CPO with their basal plane parallel to the μSZ boundary. There is no systematic relationships between the Dauphiné twinning and the μSZ. Misorientation analysis suggests that in the host grain dislocation creep is dominant on {m} slip system, whereas it is probably a minor mechanism within μSZ. Subgrains and low-angle boundaries (LAB) are heterogeneously developed at the border of the μSZ, and more commonly occur around the tips of μSZ. LABs are

  1. Quartz tuning fork based microwave impedance microscopy

    Science.gov (United States)

    Cui, Yong-Tao; Ma, Eric Yue; Shen, Zhi-Xun

    2016-06-01

    Microwave impedance microscopy (MIM), a near-field microwave scanning probe technique, has become a powerful tool to characterize local electrical responses in solid state samples. We present the design of a new type of MIM sensor based on quartz tuning fork and electrochemically etched thin metal wires. Due to a higher aspect ratio tip and integration with tuning fork, such design achieves comparable MIM performance and enables easy self-sensing topography feedback in situations where the conventional optical feedback mechanism is not available, thus is complementary to microfabricated shielded stripline-type probes. The new design also enables stable differential mode MIM detection and multiple-frequency MIM measurements with a single sensor.

  2. Quartz: structural and thermodynamic analyses across the α ↔ β transition with origin of negative thermal expansion (NTE) in β quartz and calcite

    Energy Technology Data Exchange (ETDEWEB)

    Antao, Sytle M.

    2016-04-01

    The temperature variation,T, of the crystal structure of quartz, SiO2, from 298 to 1235 K was obtained with synchrotron powder X-ray diffraction data and Rietveld structure refinements. The polymorphic transformation fromP3221 (low-T, α quartz) toP6222 (high-T, β quartz) occurs at a transition temperature,Ttr= 847 K. TheTvariations of spontaneous strains and several structural parameters are fitted to an order parameter,Q, using Landau theory. The change in Si atom coordinate, Six, givesTtr-Tc= 0.49 K, which indicates an α ↔ β transition that is weakly first order and nearly tricritical in character (Q4T). Strains give higherTtr-Tcvalues (≃ 7 K). Other fitted parameters are the oxygen Ozcoordinate, Si—Si distance, Si—O—Si and φ angles, and intensity of the (111) reflection,I111. In α quartz, the Si—Si distance increases withTbecause of cation repulsion, so the Si—O—Si angle increases (and φ decreases) and causes the thermal expansion of the framework structure that consists of corner-sharing distorted rigid SiO4tetrahedra. The Si—Si distances contract withTand cause negative thermal expansion (NTE) in β quartz because of increasing thermal librations of the O atom in the Si—O—Si linkage that occur nearly perpendicular to the Si—Si contraction. In calcite, CaCO3, the short Ca—Ca distance expands withT, but the next-nearest Ca—Ca distance, which is of equal length to theaaxis, contracts withTand causes NTE along

  3. Quartz enhanced photoacoustic spectroscopy based trace gas sensors using different quartz tuning forks.

    Science.gov (United States)

    Ma, Yufei; Yu, Guang; Zhang, Jingbo; Yu, Xin; Sun, Rui; Tittel, Frank K

    2015-03-27

    A sensitive trace gas sensor platform based on quartz-enhanced photoacoustic spectroscopy (QEPAS) is reported. A 1.395 μm continuous wave (CW), distributed feedback pigtailed diode laser was used as the excitation source and H2O was selected as the target analyte. Two kinds of quartz tuning forks (QTFs) with a resonant frequency (f0) of 30.72 kHz and 38 kHz were employed for the first time as an acoustic wave transducer, respectively for QEPAS instead of a standard QTF with a f0 of 32.768 kHz. The QEPAS sensor performance using the three different QTFs was experimentally investigated and theoretically analyzed. A minimum detection limit of 5.9 ppmv and 4.3 ppmv was achieved for f0 of 32.768 kHz and 30.72 kHz, respectively.

  4. A new irradiated quartz for beta source calibration

    DEFF Research Database (Denmark)

    Hansen, Vicki; Murray, Andrew Sean; Buylaert, Jan-Pieter;

    2015-01-01

    laboratories have used the various different batches of Risø calibration quartz for the calibration of beta and X-ray sources, but these have been largely undescribed. Here we describe in detail the preparation and luminescence characteristics of a new quartz standard, based on a North Sea beach sand collected...

  5. Quartz exposure in agriculture: literature review and South African survey.

    NARCIS (Netherlands)

    Swanepoel, A.J.; Rees, D.; Renton, K.; Swanepoel, C.; Kromhout, H.; Gardiner, K.

    2010-01-01

    OBJECTIVES: To review the published literature on respirable quartz exposure and associated disease in agricultural related settings systematically and to describe personal respirable dust and quartz measurements collected on a sandy soil farm in the Free State province of South Africa. METHODS: The

  6. Thermal quenching of thermoluminescence in quartz samples of various origin

    Energy Technology Data Exchange (ETDEWEB)

    Subedi, B. [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124-Thessaloniki (Greece); Oniya, E. [Archaeometry Laboratory, Cultural and Educational Technology Institute (C.E.T.I.), R.C. ' Athena' , Tsimiski 58, 67100 Xanthi (Greece); Physics and Electronics Department, Adekunle Ajasin University, PMB 01, Akungba Akoko (Nigeria); Polymeris, G.S. [ISIK University, Physics Department, Faculty of Science and Arts, 34980-Sile, Istanbul (Turkey); Afouxenidis, D.; Tsirliganis, N.C. [Archaeometry Laboratory, Cultural and Educational Technology Institute (C.E.T.I.), R.C. ' Athena' , Tsimiski 58, 67100 Xanthi (Greece); Kitis, G., E-mail: gkitis@auth.g [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124-Thessaloniki (Greece)

    2011-03-15

    The effect of thermal quenching stands among the most important properties in the thermoluminescence (TL) of quartz on which many applications of TL are based. Since the quartz samples used in various applications are all of different origin it is useful to investigate whether the values of the thermal quenching parameters, i.e. the activation energy for thermal quenching W and a parameter C which describes the ratio of non-radiative to radiative luminescence transitions, evaluated mainly in specific quartz samples can be extrapolated to quartz samples of unknown origin as well as to quartz samples which are annealed at high temperatures. In the present work the TL glow curve of a series of un-annealed and annealed natural and synthetic quartz samples were studied as a function of the heating rate between 0.25 K/s and 16 K/s. Using an indirect fitting method it was found that the thermal quenching parameters W and C in most of the quartz samples are very similar to the values accepted in the literature. Furthermore, in some cases the thermal quenching parameters W and C are not the same for all TL glow-peaks in the same glow-curve. Finally, the strong external treatment of annealing the quartz samples at very high temperature can also influence at least one of the thermal quenching parameters.

  7. Recent developments of OSL techniques for dating quartz and feldspars

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Jungner, H.; Mejdahl, V.

    1993-01-01

    The construction of a unit for measuring optically stimulated luminescence from quartz and feldspar is described. The light sources used for stimulation are infrared diodes for feldspar and green light from a halogen lamp (obtained with a system of filters) for both quartz and feldspar. The unit ...

  8. Speciation and phase separation of water in quartz (A review ...

    African Journals Online (AJOL)

    Speciation and phase separation of water in quartz (A review) ... of quartz at temperatures in excess of 500 °C. leading to decomposition of the ... The nucleation is a first order phase transition of creating liquid nucleus within the vapour phase, ...

  9. Removal of Ozone by Carbon Nanotubes/Quartz Fiber Film.

    Science.gov (United States)

    Yang, Shen; Nie, Jingqi; Wei, Fei; Yang, Xudong

    2016-09-01

    Ozone is recognized as a harmful gaseous pollutant, which can lead to severe human health problems. In this study, carbon nanotubes (CNTs) were tested as a new approach for ozone removal. The CNTs/quartz fiber film was fabricated through growth of CNTs upon pure quartz fiber using chemical vapor deposition method. Ozone conversion efficiency of the CNTs/quartz fiber film was tested for 10 h and compared with that of quartz film, activated carbon (AC), and a potassium iodide (KI) solution under the same conditions. The pressure resistance of these materials under different airflow rates was also measured. The results showed that the CNTs/quartz fiber film had better ozone conversion efficiency but also higher pressure resistance than AC and the KI solution of the same weight. The ozone removal performance of the CNTs/quartz fiber film was comparable with AC at 20 times more weight. The CNTs played a dominant role in ozone removal by the CNTs/quartz fiber film. Its high ozone conversion efficiency, lightweight and free-standing properties make the CNTs/quartz fiber film applicable to ozone removal. Further investigation should be focused on reducing pressure resistance and studying the CNT mechanism for removing ozone.

  10. Shocked quartz: A {sup 29}Si magic-angle-spinning nuclear magnetic resonance study

    Energy Technology Data Exchange (ETDEWEB)

    Fiske, P.S.; Nellis, W.J. [Lawrence Livermore National Lab., CA (United States). Physics and Space Technology Directorate; Xu, Z.; Stebbins, J.F. [Stanford Univ., CA (United States). Dept. of Geological and Environmental Sciences

    1998-11-01

    Quantitative {sup 29}Si NMR spectra of single-crystal {alpha}-quartz, shock compressed to 12--38 GPa and recovered, provide new information about the complex response of quartz to shock loading. Spectra from samples recovered from shock pressures of 12--20 GPa show a broadening of the {sup 29}Si NMR peak and the development of asymmetry toward lower NMR frequency (indicating an increase in the mean Si-O-Si intertetrahedral bond angle). NMR spectra of samples shock compressed above {approximately}25 GPa show increasing amounts of a separate amorphous phase of SiO{sub 2} with a mean Si-O-Si bond angle roughly 5{degree} narrower, and 10--15% denser, than fused SiO{sub 2}. Small amounts of crystalline material remain with a mean Si-O-Si bond angle up to 3{degree} larger than unshocked {alpha}-quartz. The recovery of dense glass indicates that post-shock temperatures were sufficiently low to also preserve stishovite, had any been created in the experiments. The paucity of stishovite or Si in an amorphous phase in the recovered samples suggests that the formation of stable, high-coordinated Si is kinetically hindered in shock compression experiments up to about 35--40 GPa, except in regions of high temperature, such as planar deformation features (PDFs), microfaults (pseudotachylites), or voids.

  11. Existence and release of fluid inclusions in bornite and its associated quartz and calcite

    Science.gov (United States)

    Deng, Jiu-shuai; Wen, Shu-ming; Wu, Dan-dan; Liu, Jian; Zhang, Xiao-lin; Shen, Hai-ying

    2013-09-01

    The existence and release of fluid inclusions in bornite and its associated minerals, namely, quartz and calcite were investigated and confirmed. The structures, forms, and phases of these large quantities of fluid inclusions were also studied. A mass of fluid inclusions with various sizes, distributions, shapes, and phases exist in bornite and its associated minerals. Their sizes vary from a few micrometers to tens of micrometers, and the forms appear as negative crystals, or elongated, elliptical, and irregular. At room temperature, fluid inclusions were mainly characterized as gas-liquid twophase. However, small amounts of fluid inclusions with pure gas phase and pure liquid single-phase were also observed in quartz and calcite. These fluid inclusions initially broke during the ore crushing and grinding process and then released into the flotation pulp in the flotation process. The quantitative analysis of fluid inclusions in the solution and the comparisons of mineral dissolution show that the amount of copper and iron released by fluid inclusions in the bornite sample is higher than the amount dissolved by the mineral; fluid inclusions in the associated gangue minerals, quartz, and calcite also make contribution.

  12. Formation and properties of water from quartz and hydrogen at high pressure and temperature

    Science.gov (United States)

    Futera, Zdenek; Yong, Xue; Pan, Yuanming; Tse, John S.; English, Niall J.

    2017-03-01

    Quartz, as the most stable low-pressure polymorph of silica (SiO2), is widely abundant in Earth's crust and mantle, exhibiting relatively high chemical stability. Although silica is only slightly soluble in water at ambient conditions, producing silicon-based weakly acidic compounds, Shinozaki et al. (2014) have shown recently that water itself can be formed by dissolution of SiO2 in H2 fluid under high- temperature and pressure conditions. Here, we have simulated this process via molecular-dynamics techniques based on a reactive force-field description of the Si O2 /H2 interface. Diffusion of the H2 fluid into the quartz crystal lattice was observed upon increasing temperature and pressure, followed by interaction of dissociated, atomic hydrogen with oxygen atoms in the SiO2 lattice, disrupting the lattice and leading to the formation of water. Interestingly, water is evolved in the subsurface region of the silica, and it remains confined there, isolated from the hydrogen fluid, which corresponds precisely to the ice-like spectroscopic patterns observed experimentally. The over-pressured water formed from quartz and H2 is a possible trigger for nucleating enigmatic deep earthquakes in the continental mantle lithosphere.

  13. The Growth Entrapment Model (GEM): New Insights from Molecular-Scale Simulations of Ti in Quartz

    Science.gov (United States)

    Watson, E. B.; Lanzillo, N. A.; Nayak, S. K.

    2011-12-01

    The growth entrapment model (GEM) put forth by Watson and Liang (Am. Min. 80, 1170-1187) and Watson (GCA 68, 1473-1488) offers a mechanism by which crystals can acquire non-equilibrium chemical or isotopic properties during growth from a uniform fluid medium. The GEM is based on the premise that the equilibrium properties of the near-surface region of a crystal differ from those of the bulk, much as the properties of nanocrystals differ from those of larger crystals of the same phase. In the GEM model, "capture" of the near-surface composition within a growing crystal-creating a non-equilibrium condition-depends upon the outcome of the competition between growth (which buries near-surface atoms) and diffusion (which attempts to restore equilibrium). In any application of the GEM model, the most uncertain input parameters are the near-surface diffusivity (D) and the equilibrium partition coefficient (F) between the near-surface region and the bulk lattice. Experimental measurement of these quantities is elusive because the relevant length scales are small (1-5 nm). However, molecular-scale simulations hold some promise for deducing relative values, as we illustrate here using Ti uptake in quartz as an example. We undertook ab initio molecular dynamics simulations based on a supercell approach to show that the binding energy of Ti^{4+} in quartz is a function of depth in the crystal within a few nanometers of the surface, confirming that F in the GEM model must differ from unity. We also show, using the meta-dynamics method to compute the unbiased diffusion path and corresponding energy barrier, that the activation energy for Ti^{4+} diffusion in the near-surface (2-3 nm deep) is substantially lower than that pertaining to the "deep" lattice diffusivity that is typically measured in diffusion experiments (which we also reproduced computationally). These findings substantiate the underlying phenomena upon which the GEM model is based, in addition to providing

  14. A Dynamic Pressure Component in UHP Whiteschists from the Dora-Maira Massif (Western Alps, Italy) Revealed By Pressure-Induced Incipient Amorphization of Quartz

    Science.gov (United States)

    Frezzotti, M. L.; Palmeri, R.; Godard, G.; Ferrando, S.; Compagnoni, R.

    2014-12-01

    We report the micro-Raman evidence for pressure-induced incipient amorphization of quartz in the UHP Brossasco-Isasca Unit (Dora-Maira Massif, Italian western Alps). Fifteen quartz inclusions in garnet were studied that comprise single crystals and aggregates of two-to-four crystals, along with one matrix crystal in a strain shadow. Palisade quartz, from coesite inversion, is also observed in garnet. The straight alignment of inclusions in prograde garnet indicates that quartz grew during garnet growth at about 650°C and 2.8 GPa, from HP to UHP metamorphic conditions. In single quartz crystals, disordering of lattice and densification (i.e., diaplectic glass) are revealed by two additional bands in Raman spectra: the former at 480 cm-1, derived from tetrahedral densified SiO2 amorphous phase composed of four-membered rings, and the latter at 605 cm-1, from defect structures involving partially broken SiO2 bonds. At the P-T metamorphic conditions of garnet growth, coesite is the thermodynamically stable form of crystalline silica. The existence of a lower enthalpy configuration, however, is a necessary but not sufficient condition for phase transition at constant pressure. If a kinetically accessible path is not available for the transition to ensue, metastable denser amorphous phase is formed instead. Amorphization of α-quartz requires experimental (or theoretical) lithostatic (hydrostatic) pressures > 15 GPa, while in presence of deviatoric stresses (i.e., non-lithostatic conditions), required pressures are lowered down to ≤ 5 GPa, at room temperature. Previous numerical geodynamic models suggested that in UHP terranes tectonic overpressure, greater than up to 0.3 GPa the lithostatic one, may be locally present (Gerya et al., 2008, Lithos, 103, 236-256). Our study confirms the presence of transitory pressure deviations from lithostatic values during prograde UHP metamorphism on a time scale that allows minerals to record these pressures.

  15. 石英晶粒度对石英捣打料性能的影响%Effect of quartz crystalline size on physical properties of quartz ramming mix

    Institute of Scientific and Technical Information of China (English)

    李享成; 朱伯铨; 王峰裕

    2012-01-01

    研究了平均晶粒度分别为147、166和550 μm的3种石英对石英捣打料加热永久线变化和强度的影响.结果表明:不同晶粒度的石英,其晶型转变温度也不尽相同,主要原因在于石英的结晶度不同,其热效应出现差异.石英捣打料在1 100℃热处理后失去自由水和结晶水而导致收缩;1 600℃烧后,由于存在鳞石英向方石英的相转变,有显著的体积膨胀,且随着晶粒增大,体积膨胀减小,强度显著提高.%The effect of quartz crystalline size (147,166,and 550 μm respectively on average) on the permanent change in dimensions on heating and strength of quartz ramming mix was investigated. The results show that quartzes with different crystalline sizes have different phase change temperatures because of the different crystallinities and thermal effects. After fired at 1 100 °C, quartz ramming mix shrinks because of the dehydration of free water and crystal water. When fired at 1 600 °C, quartz ramming mix expands obviously for the phase change from tridymite to cristobalite;with the increasing crystalline size of quartz,the expansion decreases and the strength increases.

  16. Phase-referenced nonlinear spectroscopy of the α-quartz/water interface

    Energy Technology Data Exchange (ETDEWEB)

    Ohno, Paul E.; Saslow, Sarah A.; Wang, Hong-fei; Geiger, Franz M.; Eisenthal, Kenneth B.

    2016-12-13

    Probing the polarization of water molecules at charged interfaces by second harmonic generation (SHG) spectroscopy1 has been heretofore limited to isotropic solids. The signal intensity follows the interfacial potential, φo, according to I2ω ∝|χ(2)+ χ(3).φo|2, where I2ω is the SHG signal intensity oscillating at frequency 2ω, and χ(2) and χ(3) are the second- and third-order susceptibilities (χ(2) and χ(3)) of the interface probed. Here, we report the first phase-referenced SHG measurements under non-resonant conditions at the interface of z-cut α-quartz and water under conditions of dynamically changing ionic strength and bulk solution pH. Comparison to non-referenced SHG measurements obtained from the fused silica/water interface reveals that the χ(3).φo term takes the form of ( χ(3)±iχ(3)).φo, and that the interference between the χ(3).φo term and the bulk quartz χ(2) term depends on the rotation angle of α-quartz around the z-axis. This newly identified term, iχ(3).φo, which is out of phase from the surface terms, is of bulk origin. The experiment expands the scope of SHG spectroscopy to probe solid/liquid interfaces beyond amorphous and centrosymmetric materials towards crystal classes that lack centrosymmetry. The possibility of internally phase referencing the interfacial SHG response for the interfacial orientation analysis of species or materials in contact with α-quartz are discussed along with the implications for conditions of resonance enhancement.

  17. The evolution of model catalytic systems; studies of structure, bonding and dynamics from single crystal metal surfaces to nanoparticles, and from low pressure (10(-3) Torr) to liquid interfaces.

    Science.gov (United States)

    Somorjai, Gabor A; York, Roger L; Butcher, Derek; Park, Jeong Y

    2007-07-21

    The material and pressure gap has been a long standing challenge in the field of heterogeneous catalysis and have transformed surface science and biointerfacial research. In heterogeneous catalysis, the material gap refers to the discontinuity between well-characterized model systems and industrially relevant catalysts. Single crystal metal surfaces have been useful model systems to elucidate the role of surface defects and the mobility of reaction intermediates in catalytic reactivity and selectivity. As nanoscience advances, we have developed nanoparticle catalysts with lithographic techniques and colloidal syntheses. Nanoparticle catalysts on oxide supports allow us to investigate several important ingredients of heterogeneous catalysis such as the metal-oxide interface and the influence of noble metal particle size and surface structure on catalytic selectivity. Monodispersed nanoparticle and nanowire arrays were fabricated for use as model catalysts by lithographic techniques. Platinum and rhodium nanoparticles in the 1-10 nm range were synthesized in colloidal solutions in the presence of polymer capping agents. The most catalytically active systems are employed at high pressure or at solid-liquid interfaces. In order to study the high pressure and liquid interfaces on the molecular level, experimental techniques with which we bridged the pressure gap in catalysis have been developed. These techniques include the ultrahigh vacuum system equipped with high pressure reaction cell, high pressure Sum Frequency Generation (SFG) vibration spectroscopy, High Pressure Scanning Tunneling Microscopy (HP-STM), and High Pressure X-ray Photoemission Spectroscopy (HP-XPS), and Quartz Crystal Microbalance (QCM). In this article, we overview the development of experimental techniques and evolution of the model systems for the research of heterogeneous catalysis and biointerfacial studies that can shed light on the long-standing issues of materials and pressure gaps.

  18. Granular encapsulation of light hydrophobic liquids (LHL) in LHL-salt water systems: Particle induced densification with quartz sand.

    Science.gov (United States)

    Boglaienko, Daria; Tansel, Berrin; Sukop, Michael C

    2016-02-01

    Addition of granular materials to floating crude oil slicks can be effective in capturing and densifying the floating hydrophobic phase, which settles by gravity. Interaction of light hydrophobic liquids (LHL) with quartz sand was investigated in LHL-salt water systems. The LHLs studied were decane, tetradecane, hexadecane, benzene, toluene, ethylbenzene, m-xylene, and 2-cholorotoluene. Experiments were conducted with fine quartz sand (passing sieve No. 40 with openings 0.425 mm). Each LHL was dyed with few crystals of Sudan IV dye for ease of visual observation. A volume of 0.5 mL of each LHL was added to 100 mL salt water (34 g/L). Addition of one gram of quartz sand to the floating hydrophobic liquid layer resulted in formation of sand-encapsulated globules, which settled due to increased density. All LHLs (except for a few globules of decane) formed globules covered with fine sand particles that were heavy enough to settle by gravity. The encapsulated globules were stable and retained their shape upon settling. Polarity of hydrophobic liquids as the main factor of aggregation with minerals was found to be insufficient to explain LHL aggregation with sand. Contact angle measurements were made by submerging a large quartz crystal with the LHL drop on its surface into salt water. A positive correlation was observed between the wetting angle of LHL and the LHL volume captured (r = 0.75). The dependence of the globule density on globule radius was analyzed in relation to the coverage (%) of globule surface (LHL-salt water interface) by fine quartz particles. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Research on 2D representation method of wireless Micro-Ball endoscopic images.

    Science.gov (United States)

    Wang, Dan; Xie, Xiang; Li, Guolin; Gu, Yingke; Yin, Zheng; Wang, Zhihua

    2012-01-01

    Nowadays the interpretation of the images acquired by wireless endoscopy system is a tedious job for doctors. A viable solution is to construct a map, which is the 2D representation of gastrointestinal (GI) tract to reduce the redundancy of images and improve the understandability of them. The work reported in this paper addresses the problem of the 2D representation of GI tract based on a new wireless Micro-Ball endoscopy system with multiple image sensors. This paper firstly models the problem of constructing the map, and then discusses mainly on the issues of perspective distortion correction, image preprocessing and image registration, which lie in the whole problem. The perspective distortion correction algorithm is realized based on attitude angles, while the image registration is based on phase correlation method (PCM) and scale invariant feature transform (SIFT) combined with particular image preprocessing methods. Based on R channels of images, the algorithm can deal with 26.3% to 100% of image registration when the ratio of overlap varies from 25% to 80%. The performance and effectiveness of the algorithms are verified by experiments.

  20. Intracavity quartz-enhanced photoacoustic sensor

    Energy Technology Data Exchange (ETDEWEB)

    Borri, S., E-mail: simone.borri@ino.it; Galli, I.; Mazzotti, D.; Giusfredi, G.; De Natale, P. [CNR-INO UOS Sesto Fiorentino and LENS, via Carrara 1, 50019 Sesto Fiorentino FI (Italy); Patimisco, P.; Scamarcio, G.; Spagnolo, V. [CNR-IFN UOS Bari and Dipartimento Interateneo di Fisica, Università degli Studi di Bari e Politecnico di Bari, via Amendola 173, 70126 Bari BA (Italy); Akikusa, N. [Development Bureau Laser Device R and D Group, Hamamatsu Photonics KK, Shizuoka 434-8601 (Japan); Yamanishi, M. [Central Research Laboratories, Hamamatsu Photonics KK, Shizuoka 434-8601 (Japan)

    2014-03-03

    We report on a spectroscopic technique named intracavity quartz-enhanced photoacoustic spectroscopy (I-QEPAS) employed for sensitive trace-gas detection in the mid-infrared spectral region. It is based on a combination of QEPAS with a buildup optical cavity. The sensor includes a distributed feedback quantum cascade laser emitting at 4.33 μm. We achieved a laser optical power buildup factor of ∼500, which corresponds to an intracavity laser power of ∼0.75 W. CO{sub 2} has been selected as the target molecule for the I-QEPAS demonstration. We achieved a detection sensitivity of 300 parts per trillion for 4 s integration time, corresponding to a noise equivalent absorption coefficient of 1.4 × 10{sup −8} cm{sup −1} and a normalized noise-equivalent absorption of 3.2 × 10{sup −10} W cm{sup −1} Hz{sup −1/2}.

  1. The effect of experiment geometry on the mechanism and rate of dissolution of quartz in basanite at 0.5GPa and 1350°C

    Science.gov (United States)

    Shaw, Cliff S. J.

    Mineral dissolution is an important factor in many magmatic processes such as melting, assimilation and magma mixing. Since it is not possible to determine dissolution rates or mechanisms from natural samples, experimental measurements are very useful. However, the geometry of the crystal-melt system can have a large effect on the measured rate, depending on whether the contaminated melt formed during dissolution is gravitationally stable or unstable. This study examines the effects of the crystal-melt geometry on the dissolution rate and mechanism. The experiments were performed using basanite melt and cylinders and spheres prepared from a single crystal of natural quartz. All of the experiments were performed in the piston cylinder apparatus at 0.5GPa and 1350°C. Four crystal-melt geometries were used: (1) quartz cylinders on top of a column of melt; (2) quartz cylinders beneath a column of basanite melt; (3) quartz cylinders in the middle of column of melt; (4) quartz spheres on top of a column of basanite melt. These geometries allow an examination of non-convective, convective and mixed non-convective/convective dissolution. Sphere experiments were included, as this has been the most commonly used geometry in previous experimental studies. In all of the experiments quartz dissolves directly into the basanite without formation of cristobalite or tridymite. Quartz on top of a column of melt dissolves at a rate almost proportional to the square root of time and forms a silica-rich compositional boundary layer that is gravitationally stable. All of the samples show well-defined compositional gradients in the boundary layer; however, the melt at the interface varies in composition with time and plots of concentration as a function of distance normalized to time show that the diffusion rate of SiO2 increases with time. These data suggest that the rate-controlling step during quartz dissolution is interface reaction rather than cation diffusion. Quartz on the bottom

  2. New quartz oscillator switching method for nano-Henry range inductance measurements.

    Science.gov (United States)

    Matko, Vojko; Jezernik, Karel

    2012-01-01

    This article introduces a new method for nano-Henry inductance measurements at the frequency of 4.999 MHz with a single quartz crystal oscillating in the switching oscillating circuit. The real novelty of this method, however, lies in a considerable reduction of the temperature influence of AT-cut crystal frequency change in the temperature range between 0 °C and 50 °C through a switching method which compensates for the crystal's natural temperature characteristics. This allows for the compensation of any influences on the crystal such as the compensation of the non-linear temperature characteristics and the ageing of both the crystal and other oscillating circuit elements, as well as the reduction of the output frequency measurement errors with the help of an additional reference frequency. The experimental results show that the switching method greatly improves the measurement of small inductance changes in the range between μH and nH, allowing as a result high-precision measurements (~0.35 fH) in this range.

  3. Zoning and sectoriality of the florencite and xenotime group minerals from quartz veins, the Subpolar Urals

    Science.gov (United States)

    Repina, S. A.

    2010-12-01

    A detailed study of the florencite and xenotime assemblage from quartz veins of Au-REE occurrences in the Subpolar Urals allowed the REE fractionation and distribution of REE mixtures in the crystal structure to be characterized. In minerals of selective composition, isomorphic mixtures of LREE and HREE are divided into lanthanum Lasg (La-Pr) and samarium Smsg (Nd-Eu) subgroups in florencite and gadolinium Gdsg (Gd-Dy) and ytterbium Ybsg (Ho-Lu) subgroups in xenotime. Concentrations of elements from these subgroups are inversely proportional to each other. Each florencite or xenotime crystal is characterized by several mineral varieties: xenotime-(Y) and Gd-bearing xenotime-(Y), florencite-(Sm), -(Nd), and -(Ce); they are selectively distributed by growth zones and pyramids of the crystal with formation of direct and inverse zoning. In both cases, cores of the crystals are enriched in HREE. The correlation between REEs, Y, and such trace elements as As, S, Ca, Sr, U, and Sc is established. REE deportment is considered in minerals formed as products of primary crystallization and hydrothermal redeposition. The REE fractionation is interpreted in terms of quantum mechanics.

  4. In-homogeneity in the pre-dose sensitization of the 110 Degree-Sign C TL peak in various quartz samples: The influence of annealing

    Energy Technology Data Exchange (ETDEWEB)

    Polymeris, George S., E-mail: polymers@auth.gr [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); ISIK University, Faculty of Science and Arts, Physics Department, Sile 34980, Istanbul (Turkey); Oniya, Ebenezer O. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); Physics and Electronics Department, Adekunle Ajasin University, PMB 01 Akungba Akoko (Nigeria); Jibiri, Nnamdi N. [Department of Physics, University of Ibadan, Ibadan (Nigeria); Tsirliganis, Nestor C. [Laboratory of Radiation Applications and Archaeological Dating, Department of Archaeometry and Physicochemical Measurements, Cultural and Educational Technology Institute, Athena, Research and Innovation Center in Information, Communication and Knowledge Technologies, Tsimiski 58, GR-67100 Xanthi (Greece); Kitis, George [Aristotle University of Thessaloniki, Nuclear Physics Laboratory, 54124 Thessaloniki (Greece)

    2012-03-01

    The pre-dose sensitization effect of the 110 Degree-Sign C TL glow-peak of quartz is a basic tool in thermoluminescence and optically stimulated luminescence dating and retrospective dosimetry. In the present work, a homogeneity study was performed on pre-dose sensitization in grains obtained from large quartz crystals samples collected from 10 different origins. The aliquot - to - aliquot scatter of the pre-dose sensitization of the 110 Degree-Sign C TL peak within each quartz crystal was monitored. The influence of the annealing on this scattering was also studied. Therefore, the investigation was applied to the un-fired 'as is' samples as well as to samples annealed at 900 Degree-Sign C for 1 h following cooling to room temperature in air. The results showed that in the case of 'as is' quartz the sensitization effect vary strongly within each aliquot of the same quartz sample. This strong variation is removed by both the high temperature annealing as well as heating up to 500 Degree-Sign C, involved in the TL measurements. These results are generally discussed in the framework of existing models and applications of the effect.

  5. A spectroscopic method for determining thickness of quartz wave plate

    Institute of Scientific and Technical Information of China (English)

    Weiwei Feng; Lihuang Lin; Ligang Chen; Huafeng Zhu; Ruxin Li; Zhizhan Xu

    2006-01-01

    A spectroscopic method to determine thickness of quartz wave plate is presented. The method is based on chromatic polarization interferometry. With the polarization-resolved transmission spectrum (PRTS)curve, the phase retardation of quartz wave plate can be determined at a wide spectral range from 200 to2000 nm obviously. Through accurate judgment of extreme points of PRTS curve at long-wave band, the physical thickness of quartz wave plates can be obtained exactly. We give a measuring example and the error analysis. It is found that the measuring precision of thickness is mainly determined by the spectral resolution of spectrometer.

  6. Radiatively heated high voltage pyroelectric crystal pulser

    Energy Technology Data Exchange (ETDEWEB)

    Antolak, A.J., E-mail: antolak@sandia.gov [Sandia National Laboratories, Livermore, CA 94550 (United States); Chen, A.X. [Sandia National Laboratories, Livermore, CA 94550 (United States); Leung, K.-N. [Sandia National Laboratories, Livermore, CA 94550 (United States); Nuclear Engineering Department, University of California, Berkeley (United States); Morse, D.H.; Raber, T.N. [Sandia National Laboratories, Livermore, CA 94550 (United States)

    2014-01-21

    Thin lithium tantalate pyroelectric crystals in a multi-stage pulser were heated by quartz lamps during their charging phase to generate high voltage pulses. The charging voltage was determined empirically based on the measured breakdown voltage in air and verified by the induced breakdown voltage of an external high voltage power supply. A four-stage pyroelectric crystal device generated pulse discharges of up to 86 kV using both quartz lamps (radiative) and thermoelectric (conductive) heating. Approximately 50 mJ of electrical energy was harvested from the crystals when radiatively heated in air, and up to 720 mJ was produced when the crystals were submerged in a dielectric fluid. It is anticipated that joule-level pulse discharges could be obtained by employing additional stages and optimizing the heating configuration.

  7. Diagenesis of 1900-year-old siliceous sinter (opal-A to quartz) at Opal Mound, Roosevelt Hot Springs, Utah, U.S.A.

    Science.gov (United States)

    Lynne, Bridget Y.; Campbell, Kathleen A.; Moore, J. N.; Browne, P. R. L.

    2005-08-01

    White, vitreous, siliceous sinter dated by 14C at ˜1900 years BP is located along the crest of the Opal Mound deposit at Roosevelt Hot Springs, Utah, U.S.A. Deposition at vents resulted from the Opal Mound fault opening conduits to the surface, allowing thermal fluids to discharge. Fault movement subsequently fractured the sinter and initiated a second period of fluid discharge. Colorful silica was deposited in this later period and formed the distal slope sinter, dated at ˜1600 years BP. The sinter preserves both end-members in the mineralogical maturation of silica, from initial opal-A to mature quartz, and also records incremental intermediate steps, as revealed by X-ray powder diffractrometry and by scanning electron, optical and Raman laser microscopy. Textural and mineralogical changes from one silica phase to another transpired gradually and gradationally. During diagenesis, incremental morphological changes alternated three times through nano- to micro-particle size transitions. The three corresponding mineralogical steps comprise: (1) opal-A to opal-CT, (2) opal-CT to opal-C, and (3) opal-C to quartz. Mineralogical changes preceded all morphological changes. Each step was initiated when silica nanostructures reached a critical diameter of 200 nm. The initial starting point of fresh (modern), polymeric, siliceous sinter deposition worldwide is nano-spherical particles of colloidal opal-A. Opaline sinter at Opal Mound is slightly more mature, reflecting the beginning of the aging process, and comprises botryoidal clusters of silica microspheres (quartz formation, the opal-C nano-rods recrystallize into groups of blocky nanostructures, each up to 200 × 300 nm. Quartz crystals grow at the expense of and pseudomorph opal-C, shown by remnant bands of blocky nanostructures at the base of the quartz crystals. Two generations of quartz crystals occur at Opal Mound: (1) diagenetic, which developed as opal-C nanostructures recrystallize to quartz; and (2

  8. Structure optimization and simulation analysis of the quartz micromachined gyroscope

    Science.gov (United States)

    Wu, Xuezhong; Wang, Haoxu; Xie, Liqiang; Dong, Peitao

    2014-03-01

    Structure optimization and simulation analysis of the quartz micromachined gyroscope are reported in this paper. The relationships between the structure parameters and the frequencies of work mode were analysed by finite element analysis. The structure parameters of the quartz micromachined gyroscope were optimized to reduce the difference between the frequencies of the drive mode and the sense mode. The simulation results were proved by testing the prototype gyroscope, which was fabricated by micro-electromechanical systems (MEMS) technology. Therefore, the frequencies of the drive mode and the sense mode can match each other by the structure optimization and simulation analysis of the quartz micromachined gyroscope, which is helpful in the design of the high sensitivity quartz micromachined gyroscope.

  9. Origin of organism-dependent biogenic silica quartz formation.

    Science.gov (United States)

    Sato, Kiminori

    2011-12-15

    Organism-dependent biogenic quartz formation in the steady-state environment is a phenomenon that can address the global environmental issues such as diagenetic evolution, biogeochemical cycling, and reservoir formation, but detailed studies have not been performed so far. Here, steady-state quartz formation is studied for amorphous silica of different biogenic origin on the basis of the recently established mechanistic model [Sato et al., J. Phys. Chem. C 2011, 115, 18131]. Amorphous silica originated from rice husks possesses angstrom-scale pores larger by 1.3 Å than those originated from diatom algae. The slight difference of pore size dramatically reduces activation energies of water diffusion by 78% and reactions of water molecules at pore surfaces by 47%, resulting in the reduction of activation energy of biogenic quartz formation by 64%. The present findings evidence that angstrom-scale pores intrinsically residing in the amorphous matrix are the organism-dependent origin of steady-state biogenic quartz formation.

  10. Degradation of glycine and alanine on irradiated quartz.

    Science.gov (United States)

    Pawlikowski, Maciej; Benko, Aleksandra; Wróbel, Tomasz P

    2013-04-01

    Recent researches suggest participation of minerals in the formation of life under primordial conditions. Among all of the minerals, quartz seems to be one of the most probable to take part in such processes. However, an external source of energy is needed, e.g. electric discharge. A device simulating the proposed conditions was designed and was used to simulate prebiotic conditions. Investigation of processes occurring during the stimulation of quartz with electric discharge was studied by means of Ultraviolet-visible (UV-VIS) spectroscopy, in order to monitor the generation kinetics of free radicals. Additionally, infrared spectroscopy was applied to identify chemical reaction products created in a solution of alanine or glycine, in the presence of quartz treated with electric discharge. Formation of increased amounts of free radicals, compared to experiments performed without quartz and/or amino acid, is reported, along with identification of possible degradation products of alanine. No synthetic reactions were observed.

  11. Quartz Fibers For Laser Therapy In Tissue Contact

    Science.gov (United States)

    Lenz, P.; Sabber, G.; Lambert, R.; Berger, F.

    1984-03-01

    Quartz fibers not protected by a gas stream and used in tissue contact can work virtually indefinitely due to "self cleaning" and "regeneration". Tissue lesions are similar to those obtained with conventional devices.

  12. Structure optimization and simulation analysis of the quartz micromachined gyroscope

    Directory of Open Access Journals (Sweden)

    Xuezhong Wu

    2014-02-01

    Full Text Available Structure optimization and simulation analysis of the quartz micromachined gyroscope are reported in this paper. The relationships between the structure parameters and the frequencies of work mode were analysed by finite element analysis. The structure parameters of the quartz micromachined gyroscope were optimized to reduce the difference between the frequencies of the drive mode and the sense mode. The simulation results were proved by testing the prototype gyroscope, which was fabricated by micro-electromechanical systems (MEMS technology. Therefore, the frequencies of the drive mode and the sense mode can match each other by the structure optimization and simulation analysis of the quartz micromachined gyroscope, which is helpful in the design of the high sensitivity quartz micromachined gyroscope.

  13. Low-temperature intracrystalline deformation microstructures in quartz

    NARCIS (Netherlands)

    Derez, Tine; Pennock, Gill; Drury, Martyn; Sintubin, Manuel

    A review of numerous genetic interpretations of the individual low-temperature intracrystalline deformation microstructures in quartz shows that there is no consensus concerning their formation mechanisms. Therefore, we introduce a new, purely descriptive terminology for the three categories of

  14. Probing Colloid-Substratum Contact Stiffness by Acoustic Sensing in a Liquid Phase

    NARCIS (Netherlands)

    Olsson, Adam L. J.; van der Mei, Henny C.; Johannsmann, Diethelm; Busscher, Henk J.; Sharma, Prashant K.

    2012-01-01

    In a quartz crystal microbalance, particles adhering to a sensor crystal are perturbed around their equilibrium positions via thickness-shear vibrations at the crystal's fundamental frequency and overtones. The amount of adsorbed molecular mass is measured as a shift in resonance frequency. In inert

  15. Influence of quartz particles on wear in vertical roller mills

    DEFF Research Database (Denmark)

    Jensen, Lucas R.D.; Friis, Henrik; Fundal, Erling;

    2010-01-01

    statistical planning, a total of 10 tests were arried out with two different limestones and one type of quartz sand. The size distributions were kept constant and only the mixing ratios were varied. It appears from the investigation that mixtures consisting of minerals with different grindabilities result...... in an increased concentration of abrasive particles in the grinding bed ðR2 > 0:99Þ. The present study shows that the quartz concentration in the grinding bed is determining the wear rate....

  16. Average life of oxygen vacancies of quartz in sediments

    Institute of Scientific and Technical Information of China (English)

    DIAO; Shaobo(刁少波); YE; Yuguang(业渝光)

    2002-01-01

    Average life of oxygen vacancies of quartz in sediments is estimated by using the ESR (electron spin resonance) signals of E( centers from the thermal activation technique. The experimental results show that the second-order kinetics equation is more applicable to the life estimation compared with the first order equation. The average life of oxygen vacancies of quartz from 4895 to 4908 deep sediments in the Tarim Basin is about 1018 a at 27℃.

  17. Interaction Between Graphene Oxide Nanoparticles and Quartz Sand.

    Science.gov (United States)

    Sotirelis, Nikolaos P; Chrysikopoulos, Constantinos V

    2015-11-17

    In this study, the influence of pH, ionic strength (IS), and temperature on graphene oxide (GO) nanoparticles attachment onto quartz sand were investigated. Batch experiments were conducted at three controlled temperatures (4, 12, and 25 °C) in solutions with different pH values (pH 4, 7, and 10), and ionic strengths (IS = 1.4, 6.4, and 21.4 mM), under static and dynamic conditions. The surface properties of GO nanoparticles and quartz sand were evaluated by electrophoretic mobility measurements. Derjaguin-Landau-Verwey-Overbeek (DLVO) potential energy profiles were constructed for the experimental conditions, using measured zeta potentials. The experimental results showed that GO nanoparticles were very stable under the experimental conditions. Both temperature and pH did not play a significant role in the attachment of GO nanoparticles onto quartz sand. In contrast, IS was shown to influence attachment. The attachment of GO particles onto quartz sand increased significantly with increasing IS. The experimental data were fitted nicely with a Freundlich isotherm, and the attachment kinetics were satisfactorily described with a pseudo-second-order model, which implies that the quartz sand exhibited substantial surface heterogeneity and that GO retention was governed by chemisorption. Furthermore, thermodynamic analysis revealed that the attachment process was nonspontaneous and endothermic, which may be associated with structural changes of the sand surfaces due to chemisorption. Therefore, secondary minimum interaction may not be the dominant mechanism for GO attachment onto the quartz sand under the experimental conditions.

  18. Study of thermoluminescence response of purple to violet amethyst quartz from Balikesir, Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Nur, N., E-mail: nnur@adiyaman.edu.tr [Adiyaman University, Engineering Faculty, Department of Electrical and Electronic Engineering, 02040 Adiyaman (Turkey); Yeğingil, Z.; Topaksu, M. [Cukurova University, Art and Sciences Faculty, Physics Department, 01330 Adana (Turkey); Kurt, K. [University of Mersin, Science and Art Faculty, Physics Department, 33343 Mersin (Turkey); Doğan, T. [Cukurova University, Vocational School of Imamoglu, Department of Technical Programs, 01700 Adana (Turkey); Sarıgül, N. [Institute of Nuclear Science, Hacettepe University, 06532 Ankara (Turkey); Yüksel, M.; Altunal, V.; Özdemir, A.; Güçkan, V. [Cukurova University, Art and Sciences Faculty, Physics Department, 01330 Adana (Turkey); Günay, I. [Cukurova University, Medicine Faculty, Biophysics Department, Adana (Turkey)

    2015-09-01

    Highlights: • We reported on dosimetric characterisation of natural amethyst quartz specimens from Turkey, using TL technique. • The thermoluminescence characterisation tests were performed under the beta radiation exposure. • The IT peaks ∼230 °C show superlinear dose response behavior (g(D) > 1) between 1 Gy and 5 kGy. The HT peaks ∼300 °C show linear behavior (g(D) = 1) at low dose levels (1 < D < 20 Gy) and superlinearity (g(D) > 1) between 20 Gy < D < 2 kGy. • Deviations were determined for recycling measurements for various dose values of 0.1, 0.5, 0.8 and 1 kGy. • Amethyst quartz has great potential to be investigated for dosimetry purpose. - Abstract: In thermoluminescence (TL) dosimetry, the phosphor amethyst quartz as a thermoluminescent, appears to be one of the materials arousing the highest interest. In this study the dosimetric characteristics of natural amethyst quartz crystals collected from Balikesir–Dursunbey (Turkey) were investigated for the purpose of determination of the general properties that phosphors should have in order to be useful for thermoluminescence dosimetry. The natural thermoluminescence was drained by annealing the powder samples at 450 °C for 1.5 h. The effects of high temperature annealing, dose response curves, glow curves after a postirradiation annealing, reusability of the samples and storage of trapped electrons in dark at room temperature were clarified through irradiating the samples with the desired exposures by {sup 90}Sr/{sup 90}Y beta particles. Isothermal annealing before and after irradiation was found to have a definite effect upon the TL glow curve of amethyst crystal powder. The same sample varied in sensitivity depending upon its previous thermal and radiation history. The peak heights of the glow peaks were examined with respect to dose response at dose levels between 1 Gy and 5 kGy. The intermediate temperature (IT) and high temperature (HT) peaks of 230 °C and 300 °C, respectively

  19. Application of the TEOM reactor for adsorption, diffusion and kinetic studies[TEOM=Tapered Element Oscillating Microbalance

    Energy Technology Data Exchange (ETDEWEB)

    Rebo, Hans Petter

    1999-07-01

    In Norway, the limited offshore oil resources, the abundance of natural gas and the need to recover associated gas from the crude oil production have made the utilisation of natural gas the focus of increased attention. Most products from refineries and chemical industry are formed by gas phase reactions over solid materials like metals, metal oxides and zeolites. Heterogeneous catalysts are in addition frequently used for environmental purposes and energy production. In the work described in this thesis, an experimental set-up was built and used to study some typical processes in heterogeneous catalysis. The set-up included a tapered element oscillating microbalance (TEOM) for measuring mass changes. The following p