WorldWideScience

Sample records for qualified kevlar composite

  1. Kevlar reinforced neoprene composites

    Science.gov (United States)

    Penn, B. G.; Daniels, J. G.; White, W. T.; Thompson, L. M.; Clemons, L. M.

    1985-01-01

    Kevlar/neoprene composites were prepared by two techniques. One method involved the fabrication of a composite from a rubber prepreg prepared by coating Kevlar with viscous neoprene solution and then allowing the solvent to evaporate (solution impregnation technique). The second method involved heating a stack of Kevlar/neoprene sheets at a temperature sufficient to cause polymer flow (melt flow technique). There was no significant difference in the breaking strength and percent elongation for samples obtained by the two methods; however the shear strength obtained for samples fabricated by the solution impregnation technique (275 psi) was significantly higher than that found for the melt flow fabricated samples (110 psi).

  2. Kevlar reinforced neoprene composites

    International Nuclear Information System (INIS)

    Penn, B.G.; Daniels, J.G.; White, W.T.; Thompson, L.M.; Clemons, L.M.

    1985-01-01

    Kevlar/neoprene composites were prepared by two techniques. One method involved the fabrication of a composite from a rubber prepreg prepared by coating kevlar with viscous neoprene solution and then allowing the solvent to evaporate (solution impregnation technique). The second method involved heating a stack of kevlar/neoprene sheets at a temperature sufficient to cause polymer flow (melt flow technique). There was no significant difference in the breaking strength and percent elongation for samples obtained by the two methods; however the shear strength obtained for samples fabricated by the solution impregnation technique (275 psi) was significantly higher than that found for the melt flow fabricated samples (110 psi). 1 reference, 2 tables

  3. Impact behaviour of auxetic Kevlar®/ epoxy composites

    Science.gov (United States)

    Yang, S.; Chalivendra, V. B.; Kim, Y. K.

    2017-10-01

    Experimental study was performed to investigate fracture and impact properties of novel Auxetic Kevlar® laminated composites. For comparison, standard Kevlar® woven composites with and without polyurethane surface treatment were also considered in this study. For these three composites, short nylon fibers of two different fiber lengths and three different fiber densities were flocked between laminates. Vacuum infusion process along with optimized compaction was employed to fabricate composites. The double cantilever beam configuration was used to investigate the fracture properties. The Auxetic Kevlar® composites showed a significant improvement of 225% in fracture toughness compared to regular woven Kevlar® composites. Furthermore, the initiation toughness was increased by 577% with the application of flocking in Auxetic Kevlar®. During impact testing, the Auxetic Kevlar® reinforced composites showed a significant reduction in damaged area compared to woven counterpart. On the other hand, the reduction in damaged area influenced the reduction in impact energy absorption.

  4. Testing of Full Scale Flight Qualified Kevlar Composite Overwrapped Pressure Vessels

    Science.gov (United States)

    Greene, Nathanael; Saulsberry, Regor; Yoder, Tommy; Forsyth, Brad; Thesken, John; Phoenix, Leigh

    2007-01-01

    Many decades ago NASA identified a need for low-mass pressure vessels for carrying various fluids aboard rockets, spacecraft, and satellites. A pressure vessel design known as the composite overwrapped pressure vessel (COPV) was identified to provide a weight savings over traditional single-material pressure vessels typically made of metal and this technology has been in use for space flight applications since the 1970's. A typical vessel design consisted of a thin liner material, typically a metal, overwrapped with a continuous fiber yarn impregnated with epoxy. Most designs were such that the overwrapped fiber would carry a majority of load at normal operating pressures. The weight advantage for a COPV versus a traditional singlematerial pressure vessel contributed to widespread use of COPVs by NASA, the military, and industry. This technology is currently used for personal breathing supply storage, fuel storage for auto and mass transport vehicles and for various space flight and aircraft applications. The NASA Engineering and Safety Center (NESC) was recently asked to review the operation of Kevlar 2 and carbon COPVs to ensure they are safely operated on NASA space flight vehicles. A request was made to evaluate the life remaining on the Kevlar COPVs used on the Space Shuttle for helium and nitrogen storage. This paper provides a review of Kevlar COPV testing relevant to the NESC assessment. Also discussed are some key findings, observations, and recommendations that may be applicable to the COPV user community. Questions raised during the investigations have revealed the need for testing to better understand the stress rupture life and age life of COPVs. The focus of this paper is to describe burst testing of Kevlar COPVs that has been completed as a part of an the effort to evaluate the effects of ageing and shelf life on full scale COPVs. The test articles evaluated in this discussion had a diameter of 22 inches for S/N 014 and 40 inches for S/N 011. The

  5. Effect of Kevlar and carbon fibres on tensile properties of oil palm/epoxy composites

    Science.gov (United States)

    Amir, S. M. M.; Sultan, M. T. H.; Jawaid, M.; Cardona, F.; Ishak, M. R.; Yusof, M. R.

    2017-12-01

    Hybrid composites with natural and synthetic fibers have captured the interests of many researchers. In this work, Kevlar/oil palm Empty Fruit Bunch (EFB)/Kevlar and carbon/oil palm EFB hybrid/carbon composites were prepared using hand lay-up technique by keeping the oil palm EFB fiber as the core material. The tensile properties which include tensile strength, tensile modulus and elongation at break were investigated. It is observed that the tensile strength and modulus for carbon/oil palm EFB/carbon hybrid composites were much higher as compared with Kevlar/oil palm EFB/Kevlar hybrid composites. However, the elongation at break for Kevlar/oil palm EFB/Kevlar hybrid composites exhibited higher value as compared to carbon/oil palm EFB/carbon hybrid composites and oil palm EFB/epoxy composites. The tensile strength for carbon/oil palm EFB/carbon hybrid composites is 93.6 MPa and the tensile modulus for carbon/oil palm EFB/carbon hybrid composites is 6.5 GPa. The elongation at break for Kevlar/oil palm EFB/Kevlar hybrid composites is 3.6%.

  6. Evaluation of mechanical properties of hybrid fiber (hemp, jute, kevlar) reinforced composites

    Science.gov (United States)

    Suresha, K. V.; Shivanand, H. K.; Amith, A.; Vidyasagar, H. N.

    2018-04-01

    In today's world composites play wide role in all the engineering fields. The reinforcement of composites decides the properties of the material. Natural fiber composites compared to synthetic fiber possesses poor mechanical properties. The solution for this problem is to use combination of natural fiber and synthetic fiber. Hybridization helps to improve the overall mechanical properties of the material. In this study, hybrid reinforced composites of Hemp fabric/Kevlar fabric/Epoxy and Jute fabric/ Kevlar fabric/Epoxy composites are fabricated using Simple hand layup technique followed by Vacuum bagging process. Appropriate test methods as per standards and guidelines are followed to analyze mechanical behavior of the composites. The mechanical characteristics like tensile, compression and flexural properties of the hybrid reinforced composites are tested as per the ASTM standards by series of tensile test; compression test and three point bending tests were conducted on the hybrid composites. A quantitative relationship between the Hemp fabric/Kevlar fabric/Epoxy and Jute/ Kevlar fabric/Epoxy has been established with constant thickness.

  7. Condition Assessment of Kevlar Composite Materials Using Raman Spectroscopy

    Science.gov (United States)

    Washer, Glenn; Brooks, Thomas; Saulsberry, Regor

    2007-01-01

    This viewgraph presentation includes the following main concepts. Goal: To evaluate Raman spectroscopy as a potential NDE tool for the detection of stress rupture in Kevlar. Objective: Test a series of strand samples that have been aged under various conditions and evaluate differences and trends in the Raman response. Hypothesis: Reduction in strength associated with stress rupture may manifest from changes in the polymer at a molecular level. If so, than these changes may effect the vibrational characteristics of the material, and consequently the Raman spectra produced from the material. Problem Statement: Kevlar composite over-wrapped pressure vessels (COPVs) on the space shuttles are greater than 25 years old. Stress rupture phenomena is not well understood for COPVs. Other COPVs are planned for hydrogen-fueled vehicles using Carbon composite material. Raman spectroscopy is being explored as an non-destructive evaluation (NDE) technique to predict the onset of stress rupture in Kevlar composite materials. Test aged Kevlar strands to discover trends in the Raman response. Strength reduction in Kevlar polymer will manifest itself on the Raman spectra. Conclusions: Raman spectroscopy has shown relative changes in the intensity and FWHM of the 1613 cm(exp -1) peak. Reduction in relative intensity for creep, fleet leader, and SIM specimens compared to the virgin strands. Increase in FWHM has been observed for the creep and fleet leader specimens compared to the virgin strands. Changes in the Raman spectra may result from redistributing loads within the material due to the disruption of hydrogen bonding between crystallites or defects in the crystallites from aging the Kevlar strands. Peak shifting has not been observed to date. Analysis is ongoing. Stress measurements may provide a tool in the short term.

  8. Ballistic Impact Response of Woven Hybrid Coir/Kevlar Laminated Composites

    Directory of Open Access Journals (Sweden)

    Azrin Hani A.R

    2016-01-01

    Full Text Available The effects of different laminated hybrid composites stacking configuration subjected to ballistic impact were investigated. The hybrid composites consist of woven coir (C and woven Kevlar (K layers laminated together. The samples of woven coir were prepared using handloom device. The composites were produced by stacking the laminated woven coir and Kevlar alternately with the presence of the binder. The samples were tested under ballistic impact with different stacking configuration. The results obtained had successfully achieved the National Institute of Justice (NIJ standard level IIA with energy absorption of 435.6 kJ and 412.2 kJ under the projectile speed of between 330 m/s and 321 m/s respectively. Samples that having Kevlar layer at the front face and woven coir layer as back face achieved partial penetration during projectile impact. This orientation is proven to have good impact energy absorption and able to stop projectile at the second panel of the composites.

  9. Optimization and characterization of woven kevlar reinforced epoxy matrix composite materials

    International Nuclear Information System (INIS)

    Imran, A.; Aslam, S.

    2007-01-01

    Composite materials are actually well established materials that have demonstrated their promising advantages among the light weight structural materials used for aerospace and advanced applications. An effort is now being made to develop and characterize the Kevlar Epoxy Composite Materials by changing the vol. fraction of Kevlar in epoxy matrix. The optimum characteristics were observed with 37% fiber with resin by applying hand-lay-up process. The composites produced were subjected to mechanical testing to evaluate the mechanical characteristics. (author)

  10. Development and characterization of woven kevlar reinforced epoxy matrix composite materials

    International Nuclear Information System (INIS)

    Imran, A.; Alam, S.; Irfan, S.; Iftikhar, F.; Raza, M.A.

    2006-01-01

    Composite materials are actually well established materials that have demonstrated their promising advantages among the light weight structural materials used for aerospace and advanced applications. A great effort is now being made to develop and characterize the Kevlar Epoxy Composite Materials by changing the % age composition of curing agent in epoxy matrix. In order to study the phenomenon; how the change in composition of curing agent effect the composite material and which optimum composition can give the optimum properties of the material, when Kevlar reinforced to Epoxy Matrix by Hand Lay-up process. It was ensured that factors which can .affect the experiment remained the same for each experiment. The composite produced were subjected to mechanical tests to analyze the performance, to optimize the material. (author)

  11. Fracture toughness behaviour of carbon fibre epoxy composite with Kevlar reinforced interleave

    International Nuclear Information System (INIS)

    Yadav, S.N.; Kumar, Vijai; Verma, Sushil K.

    2006-01-01

    This work was to evaluate as to how mode II fracture toughness G II is affected by interleave having Kevlar fibre reinforcement in the fracture plane. Thermoset interleave and chopped Kevlar fibres were applied between the carbon/epoxy composite layers. An artificial crack starter was implanted in the mid-plane to initiate the fracture process. The following five different types of carbon fibre/epoxy composites were prepared and tested. (a) Base laminate without interleave (b) unreinforced interleave and (c) 0.5, 1.0 and 1.5 mg/cm 2 chopped Kevlar fibre reinforced interleave. Results obtained show that fracture toughness G IIC enhanced up to about two times in all the laminates. However, enhancement in fracture toughness G IIC was more effective in interleaved laminate than Kevlar reinforced interleaved because of large energy absorbing capabilities of interleaf. Mechanism of fracture and toughening were examined by using scanning electron microscope

  12. Effect of chemical treatment of Kevlar fibers on mechanical interfacial properties of composites.

    Science.gov (United States)

    Park, Soo-Jin; Seo, Min-Kang; Ma, Tae-Jun; Lee, Douk-Rae

    2002-08-01

    In this work, the effects of chemical treatment on Kevlar 29 fibers have been studied in a composite system. The surface characteristics of Kevlar 29 fibers were characterized by pH, acid-base value, X-ray photoelectron spectroscopy (XPS), and FT-IR. The mechanical interfacial properties of the final composites were studied by interlaminar shear strength (ILSS), critical stress intensity factor (K(IC)), and specific fracture energy (G(IC)). Also, impact properties of the composites were investigated in the context of differentiating between initiation and propagation energies and ductile index (DI) along with maximum force and total energy. As a result, it was found that chemical treatment with phosphoric acid solution significantly affected the degree of adhesion at interfaces between fibers and resin matrix, resulting in improved mechanical interfacial strength in the composites. This was probably due to the presence of chemical polar groups on Kevlar surfaces, leading to an increment of interfacial binding force between fibers and matrix in a composite system.

  13. Physical and Mechanical Characteristics of Kevlar Fiber-Reinforced PC/ABS Composites

    Directory of Open Access Journals (Sweden)

    Kuljira Sujirote

    2012-01-01

    Full Text Available In this research, the composites between polycarbonate (PC and acrylonitrile-butadiene-styrene (ABS alloy and Kevlar fiber were prepared. The flexural and tensile properties of PC/ABS alloy and its composites were determined using a universal testing machine. The synergistic behavior of flexural modulus was observed for all regions of PC contents, while the synergism of flexural strength and tensile strength were found in some PC contents. It was found that the optimum weight ratio of PC:ABS was 60:40. In the Kevlar Fiber-reinforced PC/ABS composite system at PC:ABS of 60:40, both flexural modulus and strength were increased with matrix contents. Additionally, the flexural strength drastically increased with the matrix content and then reached the maximum value of 167 MPa at the matrix content of 33.4 wt%. The results from peel test, water contact measurement, and scanning electron microscopy (SEM reveal that the interfacial adhesion between the Kevlar fiber and the polymer matrix could be improved by increasing the PC content in the matrix.

  14. Effects of Weave Styles and Crimp Gradients on Damage Tolerance and Energy-Absorption Capacities of Woven Kevlar/Epoxy Composites

    Science.gov (United States)

    2015-09-01

    Capacities of Woven Kevlar /Epoxy Composites Paul V. Cavallaro Ranges, Engineering, and Analysis Department NEWPORT Naval Undersea Warfare Center Division...the Kevlar woven fabrics and technical data and to Core Composites Inc. for fabricating the composite laminates. Reviewed and Approved: 1...Effects of Weave Styles and Crimp Gradients on Damage Tolerance and Energy-Absorption Capacities of Woven Kevlar /Epoxy Composites 5a. CONTRACT NUMBER 5b

  15. Investigation on the Crack Behaviour in Kevlar 49 Based Composite Materials using Extended Finite Element Method for Aerospace Applications

    Science.gov (United States)

    Handa, Danish; Sekhar Dondapati, Raja; Kumar, Abhinav

    2017-08-01

    Ductile to brittle transition (DTBT) is extensively observed in materials under cryogenic temperatures, thereby observing brittle failure due to the non-resistance of crack propagation. Owing to its outstanding mechanical and thermal properties, Kevlar 49 composites are widely used in aerospace applications under cryogenic temperatures. Therefore, in this paper, involving the assumption of linear elastic fracture mechanics (LEFM), mechanical characterization of Kevlar 49 composite is done using Extended Finite Element Method (X-FEM) technique in Abaqus/CAE software. Further, the failure of Kevlar 49 composites due to the propagation of crack at room temperature and the cryogenic temperature is investigated. Stress, strain and strain energy density as a function of the width of the Kevlar specimen is predicted, indicates that Kevlar 49 composites are suitable for use under cryogenic temperatures.

  16. Flight service evaluation of Kevlar-49/epoxy composite panels in wide-bodied commercial transport aircraft

    Science.gov (United States)

    Stone, R. H.

    1977-01-01

    Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after three years' service, and found to be performing satisfactorily. There are six Kevlar-49 panels on each aircraft, including sandwich and solid laminate wing-body panels, and 150 C service aft engine fairings. The service history to date indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

  17. Characterization of Kevlar Using Raman Spectroscopy

    Science.gov (United States)

    Washer, Glenn; Brooks, Thomas; Saulsberry, Regor

    2007-01-01

    This paper explores the characterization of Kevlar composite materials using Raman spectroscopy. The goal of the research is to develop and understand the Raman spectrum of Kevlar materials to provide a foundation for the development of nondestructive evaluation (NDE) technologies based on the interaction of laser light with the polymer Kevlar. The paper discusses the fundamental aspects of experimental characterization of the spectrum of Kevlar, including the effects of incident wavelength, polarization and laser power. The effects of environmental exposure of Kevlar materials on certain characteristics of its Raman spectrum are explored, as well as the effects of applied stress. This data may provide a foundation for the development of NDE technologies intended to detect the in-situ deterioration of Kevlar materials used for engineering applications that can later be extended to other materials such as carbon fiber composites.

  18. Aging results for PRD 49 III/epoxy and Kevlar 49/epoxy composite pressure vessels

    Science.gov (United States)

    Hamstad, M. A.

    1983-01-01

    Kevlar 49/epoxy composite is growing in use as a structural material because of its high strength-to-weight ratio. Currently, it is used for the Trident rocket motor case and for various pressure vessels on the Space Shuttle. In 1979, the initial results for aging of filament-wound cylindrical pressure vessels which were manufactured with preproduction Kevlar 49 (Hamstad, 1979) were published. This preproduction fiber was called PRD 49 III. This report updates the continuing study to 10-year data and also presents 7.5-year data for spherical pressure vessels wound with production Kevlar 49. For completeness, this report will again describe the specimens of the original study with PRD 49 as well as specimens for the new study with Kevlar 49.

  19. Design and Analysis of Drive Shaft using Kevlar/Epoxy and Glass/Epoxy as a Composite Material

    Science.gov (United States)

    Karthikeyan, P.; Gobinath, R.; Kumar, L. Ajith; Jenish, D. Xavier

    2017-05-01

    In automobile industry drive shaft is one of the most important components to transmit power form the engine to rear wheel through the differential gear. Generally steel drive shaft is used in automobile industry, nowadays they are more interested to replace steel drive shaft with that of composite drive shaft. The overall objective of this paper is to analyze the composite drive shaft using to find out the best replacement for conventional steel drive shaft. The uses of advanced composite materials such as Kevlar, Graphite, Carbon and Glass with proper resins ware resulted in remarkable achievements in automobile industry because of its greater specific strength and specific modulus, improved fatigue and corrosion resistances and reduction in energy requirements due to reduction in weight as compared to steel shaft. This paper is to presents, the modeling and analysis of drive shaft using Kevlar/Epoxy and Glass/Epoxy as a composite material and to find best replacement for conventional steel drive shafts with an Kevlar/epoxy or Glass/Epoxy resin composite drive shaft. Modeling is done using CATIA software and Analysis is carried out by using ANSYS 10.0 software for easy understanding. The composite drive shaft reduces the weight by 81.67 % for Kevlar/Epoxy and 72.66% for Glass/Epoxy when compared with conventional steel drive shaft.

  20. Manufacturing of kevlar/polyester composite by resin transfer moulding using conventional and microwave heating

    International Nuclear Information System (INIS)

    Abdullah, I.

    2015-01-01

    Microwave heating was incorporated into the resin transfer moulding technique. Polytetrafluoroethylene (PTFE) mould was used to cure the composite panel. Through the use of microwave heating, the mechanical and physical properties of produced Kevlar fibre/polyester composites were compared to those manufactured by conventional resin transfer moulding. The flexural modulus and flexural strength of 6-ply conventionally cured composites was 45% and 9% higher than the flexural modulus and flexural strength of 6-ply microwaved cured composites, respectively. However, 19% increase in interlaminar shear strength (ILSS) and 2% increase in compressive strength was observed in 6-ply microwave cured composites. This enhancement in ILSS and compressive strength is attributed to the better interfacial bonding of polyester resin with Kevlar fibres in microwaved cured composite, which was also confirmed via electron microscopy scanning. Furthermore, the microwave cured composite yielded maximum void contents (3%). (author)

  1. Pyrolysis responses of kevlar/epoxy composite materials on laser irradiating

    Science.gov (United States)

    Liu, Wei-ping; Wei, Cheng-hua; Zhou, Meng-lian; Ma, Zhi-liang; Song, Ming-ying; Wu, Li-xiong

    2017-05-01

    The pyrolysis responses of kevlar/epoxy composite materials are valuable to study in a case of high temperature rising rate for its widely application. Distinguishing from the Thermal Gravimetric Analysis method, an apparatus is built to research the pyrolysis responses of kevlar/epoxy composite materials irradiated by laser in order to offer a high temperature rising rate of the sample. By deploying the apparatus, a near real-time gas pressure response can be obtained. The sample mass is weighted before laser irradiating and after an experiment finished. Then, the gas products molecular weight and the sample mass loss evolution are derived. It is found that the pressure and mass of the gas products increase with the laser power if it is less than 240W, while the molecular weight varies inversely. The variation tendency is confusing while the laser power is bigger than 240W. It needs more deeper investigations to bring it to light.

  2. Debonding characteristics of adhesively bonded woven Kevlar composites

    Science.gov (United States)

    Mall, S.; Johnson, W. S.

    1988-01-01

    The fatigue damage mechanism of an adhesively bonded joint between fabric reinforced composite adherends was investigated with cracked-lap-shear specimens. Two bonded systems were studied: fabric Kevlar 49/5208 epoxy adherends bonded together with either EC 3445 or FM-300 adhesive. For each bonded system, two specimen geometries were tested. In all specimens tested, fatigue damage occurred in the form of cyclic debonding; however, the woven Kevlar specimens gave significantly slower debond growth rates and higher fracture toughness than previously found in the nonwoven adherend specimens. The surfaces for the woven adherends were not smooth; rather, they had regular crests (high spots) and troughs (low spots) due to the weave pattern. Radiographs of the specimens and examination of their failure surfaces revealed that fiber bridging occurred between the crests of the two adherends in the debonded region. The observed improvements in debond growth resistance and static fracture toughness are attributed to this bridging.

  3. Design, fabrication and structural optimization of tubular carbon/Kevlar®/PMMA/graphene nanoplate composite for bone fixation prosthesis.

    Science.gov (United States)

    Nasiri, F; Ajeli, S; Semnani, D; Jahanshahi, M; Emadi, R

    2018-05-02

    The present work investigates the mechanical properties of tubular carbon/Kevlar ® composite coated with poly(methyl methacrylate)/graphene nanoplates as used in the internal fixation of bones. Carbon fibers are good candidates for developing high-strength biomaterials and due to better stress transfer and electrical properties, they can enhance tissue formation. In order to improve carbon brittleness, ductile Kevlar ® was added to the composite. The tubular carbon/Kevlar ® composites have been prepared with tailorable braiding technology by changing the fiber pattern and angle in the composite structure and the number of composite layers. Fuzzy analyses are used for optimizing the tailorable parameters of 80 prepared samples and then mechanical properties of selected samples are discussed from the viewpoint of mechanical properties required for a bone fixation device. Experimental results showed that with optimizing braiding parameters the desired composite structure with mechanical properties close to bone properties could be produced. Results showed that carbon/Kevlar ® braid's physical properties, fiber composite distribution and diameter uniformity resulted in matrix uniformity, which enhanced strength and modulus due to better ability for distributing stress on the composite. Finally, as graphene nanoplates demonstrated their potential properties to improve wound healing intended for bone replacement, so reinforcing the PMMA matrix with graphene nanoplates enhanced the composite quality, for use as an implant.

  4. The Layer of Kevlar Angle-interlock Woven Fabric Effect on the Tensile Properties of Composite Materials

    Science.gov (United States)

    Xie, Wan-Chen; Guo, Xu-Yi; Yan, Tao; Zhang, Shang-Yong

    2017-09-01

    This article is based on the structure of three-dimensional angle-interlock longitudinal.The 3-layer, 5-layer, 7-layer and 9-layer of angle-interlock 3D fabrics are woven on sample weaving machine respectively with the 1500D Kevlar fiber twist filament produced by United States DuPont. At the same time, Kevlar plain weave fabric is woven, and three, five, seven and nine layers’ fabric are to be compared. In the process of VARTM composite technology, epoxy resin is matrix material, acetone is diluent, triethylene tetramine is curing agent and the five different fabrics are the reinforced materials respectively. Finally, eight different three-dimensional woven fabric composites were prepared. In this paper, the tensile properties of eight kinds of three-dimensional woven fabric composites were tested respectively.Finally, it is concluded that the five-layer angle-interlock woven fabric prepared by Kevlar fiber shows the best tensile property.

  5. Tribological properties of three-dimensional braided carbon/Kevlar/epoxy hybrid composites under dry and lubricated conditions

    International Nuclear Information System (INIS)

    Wan, Y.Z.; Huang, Y.; He, F.; Li, Q.Y.; Lian, J.J.

    2007-01-01

    This paper presents a study of the tribological properties of three-dimensional (3-D) braided carbon/Kevlar/epoxy hybrid composites. Their specific wear rate and the coefficient of friction were examined as a function of operating conditions (load and sliding distance) under dry and lubricated conditions. In addition, the 3-D braided hybrid composites with varying carbon to Kevlar fiber volume ratio were tested to assess hybrid effects. It was found that the friction and wear rate decreased with sliding distance and then leveled off under dry and lubricated conditions. Different changing patterns with normal load were observed under two different sliding conditions. Furthermore, it was noted that negative hybrid effects on the wear resistance and the friction coefficient were identified for the current 3-D braided hybrid system. The composite with a carbon to Kevlar ratio of 3:2 was found to have the least wear and friction among all 3-D braided hybrid composites studied. Worn surfaces were observed by scanning electron microscope (SEM) and wear mechanisms were discussed in this study

  6. Stab Resistance of Shear Thickening Fluid (STF)-Kevlar Composites for Body Armor Applications

    National Research Council Canada - National Science Library

    Egres Jr., R. G; Decker, M. J; Halbach, C. J; Lee, Y. S; Kirkwood, J. E; Kirwood, K. M; Wagner, N. J; Wetzel, E. D

    2004-01-01

    The stab resistance of shear thickening fluid (STF)-Kevlar and STF-Nylon fabric composites are investigated and found to exhibit significant improvements over neat fabric targets of equivalent areal density...

  7. Performance of kevlar fibre-reinforced rubber composite armour against shaped-charge jet penetration

    Directory of Open Access Journals (Sweden)

    Xu-dong Zu

    Full Text Available AbstractThe protective capability of the Kevlar fibre-reinforced rubber composite armour (KFRRCA at different obliquities is studied using depth-of-penetration experiments method against a 56 mm-diameter standard-shaped charge. Efficiency factors are calculated to evaluate the protection capability of the KFRRCA at different obliquities. Meanwhile, an X-ray experiment is used to observe the deformation, fracture, and scatter of the shaped-charge jet as it penetrates the composite armour. Finally, scanning electron microscopy (SEM is used to analyse the effect of the Kevlar fibre-reinforced rubber for the composite armour to resist jet penetration. The results showed that the KFEECA can be used as additional armour, because it has excellent protection capability, and it can disturb the stability of the middle part of the shaped charge jet (SCJ obviously especially when the armour at 30°and 68° obliquities.

  8. Evaluation of Impact Strength of Epoxy Based Hybrid Composites Reinforced with E-Glass/Kevlar 49

    Directory of Open Access Journals (Sweden)

    SUBHAN ALIJOGI

    2017-10-01

    Full Text Available In hybridization different fibers are stacked layer by layer to produce laminates have specific strength and stiffness and employed in light weight high strength applications. Physically mean fabricated hybrid composites used in aerospace, under water, body armors and armed forces establishment. In present work drop-weight impact response of hybrid composites were investigated by making laminates of hybrid composites. In Hybridization layers of E-glass (roving and Kevlar 49 fabrics stacked with epoxy resin. The layers formulation was set up by hand layup method. Impregnationsof epoxy resin of commercial grade (601A in fabrics were accomplished by VRTM (Vacuum Bagging Resin Transfer Molding technique. Layup placementof Glass fibers/ Kevlar at 0°/90°, 45°/45° and 30°/60° were set for this work. Mechanical properties such as impact strength, bear resistance and break resistance were analyzed by usingASTM D-256 and D-3763 standard.Experimental investigation was conducted using instrumented Dart impact and Izod Impact test. E-glass/Kevlar 49 at layup 0°/90°and 30°/60°exhibited improvedimpact strength than 45°/45°. The surface morphology and fractography were also investigated by capturing different images of Specimens by using the SEM (Scanning Electron Microscopy. The fiberreinforcement and matrix fracture were also observed by using SEM.The SEM images suggest that epoxy resin tightly bonded with Kevlar fibers whereas Glass fibers were pulled out from laminations.

  9. Evaluation of impact strength of epoxy based hybrid composites reinforced with e-glass/kevlar 49

    International Nuclear Information System (INIS)

    Jogi, S.A.; Memon, I.A.; Baloch, M.; Chandio, A.D.

    2017-01-01

    In hybridization different fibers are stacked layer by layer to produce laminates have specific strength and stiffness and employed in light weight high strength applications. Physically mean fabricated hybrid composites used in aerospace, under water, body armors and armed forces establishment. In present work drop-weight impact response of hybrid composites were investigated by making laminates of hybrid composites. In Hybridization layers of E-glass (roving) and Kevlar 49 fabrics stacked with epoxy resin. The layers formulation was set up by hand layup method. Impregnations of epoxy resin of commercial grade (601A) in fabrics were accomplished by VRTM (Vacuum Bagging Resin Transfer Molding) technique. Layup placementof Glass fibers/ Kevlar at 0 degree/90 degree, 45 degree/45 degree and 30 degree/60 degree were set for this work. Mechanical properties such as impact strength, bear resistance and break resistance were analyzed by using ASTM D-256 and D-3763 standard. Experimental investigation was conducted using instrumented Dart impact and Izod Impact test. E-glass/Kevlar 49 at layup 0 degree/90 degree and 30 degree/60 degree exhibited improvedimpact strength than 45 degree/45 degree. The surface morphology and fractography were also investigated by capturing different images of Specimens by using the SEM (Scanning Electron Microscopy). The fiberreinforcement and matrix fracture were also observed by using SEM.The SEM images suggest that epoxy resin tightly bonded with Kevlar fibers whereas Glass fibers were pulled out from laminations. (author)

  10. Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodies commercial transport aircraft

    Science.gov (United States)

    Stone, R. H.

    1983-01-01

    Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 9 years of service. There are six Kevlar-49 panels on each aircraft: a left hand and right hand set of a wing body sandwich fairing; a solid laminate under wing fillet panel; and a 422 K (300 F) service aft engine fairing. The fairings have accumulated a total of 70,000 hours, with one ship set having over 24,000 hours service. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, a few minor disbonds and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings. The service history to date indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

  11. Tensile and fatigue strength properties of Kevlar 29 aramid/epoxy unidirectional composites

    Energy Technology Data Exchange (ETDEWEB)

    Zweben, C.

    1981-07-22

    Static and fatigue tensile strength properties of filament wound undirectional Kevlar 29/epoxy, typical of filament wound material used in flywheel rotors, were studied. Machining techniques were developed to minimize fiber fuzzing on edges. The static modulus, normalized to 70% fiber volume fraction is 8.87 x 10/sup 6/ psi. The major Poisson's ratio is 0.37. The static composite tensile strength, normalized to 70% fiber volume fraction is 200 x 10/sup 3/ psi, corresponding to a fiber stress at failure of 286 x 10/sup 3/ psi, which is good for materials having a very high fiber volume fraction. The S-N curve for R = 0.7 was found to be quite flat. Although the techniques used in this program had previously been employed successfully to study the fatigue behavior of Kevlar 29/epoxy and Kevlar 49/epoxy unidirectional materials, we were unable to overcome the persistent problem of cohesive material failure in the tab regions. The apparent reason for this is the very low interlaminar shear strength of the filament wound material. 16 figures.

  12. Vacuum infusion manufacturing and experimental characterization of Kevlar/epoxy composites

    International Nuclear Information System (INIS)

    Ricciardi, M. R.; Giordano, M.; Antonucci, V.; Langella, A.; Nele, L.

    2014-01-01

    Epoxy/Kevlar composites have been manufactured by conventional Vacuum Infusion process and the Pulse Infusion technique. Pulse Infusion allows to control the pressure of the vacuum bag on the dry fiber reinforcement by using a proper designed pressure distributor that induces a pulsed transverse action and promotes the through thickness resin flow. The realized composite panel have been mechanically characterized by performing tensile and short beam shear tests according with the ASTM D3039 and ASTM D2344/D 2344M standard respectively in order to investigate the effect of Pulse Infusion on the tensile strength and ILSS

  13. Vacuum infusion manufacturing and experimental characterization of Kevlar/epoxy composites

    Science.gov (United States)

    Ricciardi, M. R.; Giordano, M.; Langella, A.; Nele, L.; Antonucci, V.

    2014-05-01

    Epoxy/Kevlar composites have been manufactured by conventional Vacuum Infusion process and the Pulse Infusion technique. Pulse Infusion allows to control the pressure of the vacuum bag on the dry fiber reinforcement by using a proper designed pressure distributor that induces a pulsed transverse action and promotes the through thickness resin flow. The realized composite panel have been mechanically characterized by performing tensile and short beam shear tests according with the ASTM D3039 and ASTM D2344/D 2344M standard respectively in order to investigate the effect of Pulse Infusion on the tensile strength and ILSS.

  14. Thermoviscoelastic characterization and prediction of Kevlar/epoxy composite laminates

    Science.gov (United States)

    Gramoll, K. C.; Dillard, D. A.; Brinson, H. F.

    1990-01-01

    The thermoviscoelastic characterization of Kevlar 49/Fiberite 7714A epoxy composite lamina and the development of a numerical procedure to predict the viscoelastic response of any general laminate constructed from the same material were studied. The four orthotropic material properties, S sub 11, S sub 12, S sub 22, and S sub 66, were characterized by 20 minute static creep tests on unidirectional (0) sub 8, (10) sub 8, and (90) sub 16 lamina specimens. The Time-Temperature Superposition-Principle (TTSP) was used successfully to accelerate the characterization process. A nonlinear constitutive model was developed to describe the stress dependent viscoelastic response for each of the material properties. A numerical procedure to predict long term laminate properties from lamina properties (obtained experimentally) was developed. Numerical instabilities and time constraints associated with viscoelastic numerical techniques were discussed and solved. The numerical procedure was incorporated into a user friendly microcomputer program called Viscoelastic Composite Analysis Program (VCAP), which is available for IBM PC type computers. The program was designed for ease of use. The final phase involved testing actual laminates constructed from the characterized material, Kevlar/epoxy, at various temperatures and load level for 4 to 5 weeks. These results were compared with the VCAP program predictions to verify the testing procedure and to check the numerical procedure used in the program. The actual tests and predictions agreed for all test cases which included 1, 2, 3, and 4 fiber direction laminates.

  15. Kenaf/Synthetic and Kevlar®/Cellulosic Fiber-Reinforced Hybrid Composites: A Review

    Directory of Open Access Journals (Sweden)

    Suhad D. Salman

    2015-08-01

    Full Text Available This paper reviews the published and ongoing research work on kenaf/synthetic and Kevlar®/cellulosic fiber-reinforced composite materials. The combination of natural fibers with synthetic fibers in hybrid composites has become increasingly applied in several different fields of technology and engineering. As a result, a better balance between performance and cost is expected to be achieved by 2015, through appropriate material design. This review is intended to provide an outline of the essential outcomes of those hybrid composite materials currently utilized, focusing on processing and mechanical and structural properties.

  16. KevlarTM Fiber-Reinforced Polybenzoxazine Alloys for Ballistic Impact Application

    Directory of Open Access Journals (Sweden)

    Chanchira Jubsilp

    2011-10-01

    Full Text Available A light weight ballistic composites from KevlarTM-reinforcing fiber having polybenzoxazine (BA/urethane prepolymer (PU alloys as a matrix were investigated in this work. The effect of alloy compositions on the ballistic composite properties was determined. The results revealed that the enhancement in the glass transition temperature (Tg of the KevlarTM-reinforced BA/PU composites compared to that of the KevlarTM-reinforced polybenzoxazine composite was observed. The increase of the elastomeric PU content in the BA/PU alloy resulted in samples with tougher characteristics. The storage modulus of the KevlarTM-reinforced BA/PU composites increased with increasing the mass fraction of polybenzoxazine. A ballistic impact test was also performed on the KevlarTM-reinforced BA/PU composites using a 9 mm handgun. It was found that the optimal contents of PU in the BA/PU alloys should be approximately 20wt%. The extent of the delaminated area and interfacial fracture were observed to change with the varied compositions of the matrix alloys. The appropriate thickness of KevlarTM-reinforced 80/20 BA/PU composite panel was 30 plies and 50 plies to resist the penetration from the ballistic impact equivalent to levels II-A and III-A of NIJ standard. The arrangement of composite panels with the higher stiffness panel at the front side also showed the best efficiency of ballistic penetration resistance.

  17. Kevlar 49/Epoxy COPV Aging Evaluation

    Science.gov (United States)

    Sutter, James K.; Salem, Jonathan L.; Thesken, John C.; Russell, Richard W.; Littell, Justin; Ruggeri, Charles; Leifeste, Mark R.

    2008-01-01

    NASA initiated an effort to determine if the aging of Kevlar 49/Epoxy composite overwrapped pressure vessels (COPV) affected their performance. This study briefly reviews the history and certification of composite pressure vessels employed on NASA Orbiters. Tests to evaluate overwrap tensile strength changes compared 30 year old samples from Orbiter vessels to new Kevlar/Epoxy pressure vessel materials. Other tests include transverse compression and thermal analyses (glass transition and moduli). Results from these tests do not indicate a noticeable effect due to aging of the overwrap materials.

  18. Flight service evaluation of Kevlar-49 epoxy composite panels in wide-bodied commercial transport aircraft

    Science.gov (United States)

    Stone, R. H.

    1984-01-01

    Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 10 years of service. There are six Kevlar-49 panels on each aircraft: a left-hand and right-hand set of a wing-body sandwich fairing; a solid laminate under-wing fillet panel; and a 422 K (300 F) service aft engine fairing. The three L-1011s include one each in service with Eastern, Air Canada, and TWA. The fairings have accumulated a total of 79,568 hours, with one ship set having nearly 28,000 hours service. The inspections were conducted at the airlines' major maintenance bases with the participation of Lockheed Engineering. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems, or any condition requiring corrective action. The only defects noted were minor impact damage, a few minor disbonds and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings. The service history obtained in this program indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

  19. Performance of kevlar fibre-reinforced rubber composite armour against shaped-charge jet penetration

    OpenAIRE

    Zu,Xu-dong; Huang,Zheng-xiang; Zhai,Wen

    2015-01-01

    AbstractThe protective capability of the Kevlar fibre-reinforced rubber composite armour (KFRRCA) at different obliquities is studied using depth-of-penetration experiments method against a 56 mm-diameter standard-shaped charge. Efficiency factors are calculated to evaluate the protection capability of the KFRRCA at different obliquities. Meanwhile, an X-ray experiment is used to observe the deformation, fracture, and scatter of the shaped-charge jet as it penetrates the composite armour. Fin...

  20. Improvement of interfacial adhesion and nondestructive damage evaluation for plasma-treated PBO and Kevlar fibers/epoxy composites using micromechanical techniques and surface wettability.

    Science.gov (United States)

    Park, Joung-Man; Kim, Dae-Sik; Kim, Sung-Ryong

    2003-08-15

    Comparison of interfacial properties and microfailure mechanisms of oxygen-plasma treated poly(p-phenylene-2,6-benzobisoxazole (PBO, Zylon) and poly(p-phenylene terephthalamide) (PPTA, Kevlar) fibers/epoxy composites were investigated using a micromechanical technique and nondestructive acoustic emission (AE). The interfacial shear strength (IFSS) and work of adhesion, Wa, of PBO or Kevlar fiber/epoxy composites increased with oxygen-plasma treatment, due to induced hydrogen and covalent bondings at their interface. Plasma-treated Kevlar fiber showed the maximum critical surface tension and polar term, whereas the untreated PBO fiber showed the minimum values. The work of adhesion and the polar term were proportional to the IFSS directly for both PBO and Kevlar fibers. The microfibril fracture pattern of two plasma-treated fibers appeared obviously. Unlike in slow cooling, in rapid cooling, case kink band and kicking in PBO fiber appeared, whereas buckling in the Kevlar fiber was observed mainly due to compressive and residual stresses. Based on the propagation of microfibril failure toward the core region, the number of AE events for plasma-treated PBO and Kevlar fibers increased significantly compared to the untreated case. The results of nondestructive AE were consistent with microfailure modes.

  1. The Influence of impact on Composite Armour System Kevlar-29/polyester-Al2O3

    Science.gov (United States)

    Ramadhan, A. A.; Abu Talib, A. R.; Mohd Rafie, A. S.; Zahari, R.

    2012-09-01

    An experimental investigation of high velocity impact responses of composite laminated plates using a helium gas gun has been presented in this paper. The aim of this study was to develop the novel composite structure that meets the specific requirements of ballistic resistance which used for body protections, vehicles and other applications. Thus the high velocity impact tests were performed on composite Kevlar-29 fiber/polyester resin with alumina powder (Al2O3). The impact test was conducted by using a cylindrical steel projectile of 7.62mm diameter at a velocity range of 160-400 m/s. The results (shown in this work) are in terms of varying plate thickness and the amount of energy absorbed by the laminated plates meanwhile we obtained that the 12mm thickness of composite plate suitable for impact loading up to 200m/s impact velocity. Therefore this composite structure (it is used to reduce the amount of Kevlar) considered most economical armoure products. We used the ANSYS AUTODYN 3D- v.12 software for our simulations. The results have been obtained a4.1% maximum errors with experimental work of energy absorption.

  2. The Influence of impact on Composite Armour System Kevlar-29/polyester-Al2O3

    International Nuclear Information System (INIS)

    Ramadhan, A A; Talib, A R Abu; Rafie, A S Mohd; Zahari, R

    2012-01-01

    An experimental investigation of high velocity impact responses of composite laminated plates using a helium gas gun has been presented in this paper. The aim of this study was to develop the novel composite structure that meets the specific requirements of ballistic resistance which used for body protections, vehicles and other applications. Thus the high velocity impact tests were performed on composite Kevlar-29 fiber/polyester resin with alumina powder (Al 2 O 3 ). The impact test was conducted by using a cylindrical steel projectile of 7.62mm diameter at a velocity range of 160-400 m/s. The results (shown in this work) are in terms of varying plate thickness and the amount of energy absorbed by the laminated plates meanwhile we obtained that the 12mm thickness of composite plate suitable for impact loading up to 200m/s impact velocity. Therefore this composite structure (it is used to reduce the amount of Kevlar) considered most economical armoure products. We used the ANSYS AUTODYN 3D- v.12 software for our simulations. The results have been obtained a4.1% maximum errors with experimental work of energy absorption.

  3. Vacuum infusion method for woven carbon/Kevlar reinforced hybrid composite

    Science.gov (United States)

    Hashim, N.; Majid, D. L.; Uda, N.; Zahari, R.; Yidris, N.

    2017-12-01

    The vacuum assisted resin transfer moulding (VaRTM) or Vacuum Infusion (VI) is one of the fabrication methods used for composite materials. Compared to other methods, this process costs lower than using prepregs because it does not need to use the autoclave to cure. Moreover, composites fabricated using this VI method exhibit superior mechanical properties than those made through hand layup process. In this study, the VI method is used in fabricating woven carbon/Kevlar fibre cloth with epoxy matrix. This paper reports the detailed methods on fabricating the hybrid composite using VI process and several precautions that need to be taken to avoid any damage to the properties of the composite material. The result highlights that the successfully fabricated composite has approximately 60% of fibres weight fraction. Since the composites produced by the VI process have a higher fibre percentage, this process should be considered for composites used in applications that are susceptible to the conditions where the fibres need to be the dominant element such as in tension loading.

  4. Kevlar/PMR-15 reduced drag DC-9 reverser stang fairing

    Science.gov (United States)

    Kawai, R. T.

    1982-01-01

    A reduced drag fairing for the afterbody enclosing the thrust reverser actuators on the DC-9 has been developed with Kevlar-49/PMR-15 advanced composite material. The improved fairing reduces airplane drag 1% compared to the production baseline. Use of composites reduces weight 40% compared to an equivalent metal fairing. The Kevlar-49/PMR-15 advanced composite is an organic matrix material system that can be used at temperatures up to 500 F.

  5. Influence of moisture on the transverse mechanical behavior of Kevlar 49/epoxy composites at 250C

    International Nuclear Information System (INIS)

    Allred, R.E.; Roylance, D.K.

    1982-01-01

    The magnitude of moisture effects on the transverse tensile properties of Kevlar 49/Fiberite 934 epoxy composites was examined. The transverse tensile test was selected so that failure modes could be determined by scanning electron microscopy. Results indicate that saturation moisture concentrations cause substantial reductions in transverse properties at 25 C compared to dry control values. Ultimate strength and elongation are observed to decrease respectively by 35 and 27 percent. Composite transverse stiffness is less sensitive to moisture, but is degraded by 14 percent. Microscopy of the fracture surfaces reveals that property reductions are accompanied by a change in failure mode from an interface dominated mechanism in the dry condition to one of filament splitting at saturation moisture contents. Increased filament compliance and the splitting failure mode may be a consequence of moisture interrupting the interchain hydrogen bonding of the Kevlar 49 filaments

  6. Flight service evaluation of kevlar-49 epoxy composite panels in wide-bodied commercial transport aircraft: Flight service report

    Science.gov (United States)

    Stone, R. H.

    1981-01-01

    Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after 7 years service. There are six Kevlar-49 panels on each aircraft: a left hand and right hand set of a wing-body sandwich fairing; a slid laminate under-wing fillet panel; and a 422 K service aft engine fairing. The three L-1011s include one each in service with Eastern, Air Canada, and TWA. The fairings have accumulated a total of 52,500 hours, with one ship set having 17.700 hours service. The inspections were conducted at the airlines' major maintenance bases with the participation of Lockheed Engineering. The Kevlar-49 components were found to be performing satisfactorily in service with no major problems or any condition requiring corrective action. The only defects noted were minor impact damage and a minor degree of fastener hole fraying and elongation. These are for the most part comparable to damage noted on fiberglass fairings. The service history to date indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

  7. Engineering properties of a filament-wound Kevlar 49/epoxy composite

    International Nuclear Information System (INIS)

    Hahn, H.T.; Chin, W.K.

    1981-01-01

    The effect of a flywheel service environment on transverse tension and compression, and longitudinal compression and shear properties of a filament-wound Kevlar/epoxy composite are evaluated. Shear strength and modulus were reduced by moisture desorption during preconditioning in a vacuum at 75 C, although room temperature strength and modulus increased for longitudinal compression. The desorption induced cracking of the laminate plies through increased residual stresses, which at 25 C were 15 MPa, higher than the transverse strength. The 75 C temperature caused lower strength and moduli except for longitudinal tension, and the complete test results are listed

  8. Fracture toughness of Kevlar 29/poly(methyl methacrylate) composite materials for surgical implantations.

    Science.gov (United States)

    Pourdeyhimi, B; Robinson, H H; Schwartz, P; Wagner, H D

    1986-01-01

    A study of the fracture behaviour of Kevlar 29 reinforced dental cement is undertaken using both linear elastic and nonlinear elastic fracture mechanics techniques. Results from both approaches--of which the nonlinear elastic is believed to be more appropriate--indicate that a reinforcing effect is obtained for the fracture toughness even at very low fibre content. The flexural strength and modulus are apparently not improved, however, by the incorporation of Kevlar 29 fibres in the PMMA cement, probably because of the presence of voids, the poor fibre/matrix interfacial bonding and unsatisfying cement mixing practice. When compared to other PMMA composite cements, the present system appears to be probably more effective than carbon/PMMA, for example, in terms of fracture toughness. More experimental and analytical work is needed so as to optimize the mechanical properties with respect to structural parameters and cement preparation technique.

  9. Teaching learning algorithm based optimization of kerf deviations in pulsed Nd:YAG laser cutting of Kevlar-29 composite laminates

    Science.gov (United States)

    Gautam, Girish Dutt; Pandey, Arun Kumar

    2018-03-01

    Kevlar is the most popular aramid fiber and most commonly used in different technologically advanced industries for various applications. But the precise cutting of Kevlar composite laminates is a difficult task. The conventional cutting methods face various defects such as delamination, burr formation, fiber pullout with poor surface quality and their mechanical performance is greatly affected by these defects. The laser beam machining may be an alternative of the conventional cutting processes due to its non-contact nature, requirement of low specific energy with higher production rate. But this process also faces some problems that may be minimized by operating the machine at optimum parameters levels. This research paper examines the effective utilization of the Nd:YAG laser cutting system on difficult-to-cut Kevlar-29 composite laminates. The objective of the proposed work is to find the optimum process parameters settings for getting the minimum kerf deviations at both sides. The experiments have been conducted on Kevlar-29 composite laminates having thickness 1.25 mm by using Box-Benkhen design with two center points. The experimental data have been used for the optimization by using the proposed methodology. For the optimization, Teaching learning Algorithm based approach has been employed to obtain the minimum kerf deviation at bottom and top sides. A self coded Matlab program has been developed by using the proposed methodology and this program has been used for the optimization. Finally, the confirmation tests have been performed to compare the experimental and optimum results obtained by the proposed methodology. The comparison results show that the machining performance in the laser beam cutting process has been remarkably improved through proposed approach. Finally, the influence of different laser cutting parameters such as lamp current, pulse frequency, pulse width, compressed air pressure and cutting speed on top kerf deviation and bottom kerf

  10. Ballistic performance of a Kevlar-29 woven fibre composite under varied temperatures

    Science.gov (United States)

    Soykasap, O.; Colakoglu, M.

    2010-05-01

    Armours are usually manufactured from polymer matrix composites and used for both military and non-military purposes in different seasons, climates, and regions. The mechanical properties of the composites depend on temperature, which also affects their ballistic characteristics. The armour is used to absorb the kinetic energy of a projectile without any major injury to a person. Therefore, besides a high strength and lightness, a high damping capacity is required to absorb the impact energy transferred by the projectile. The ballistic properties of a Kevlar 29/polyvinyl butyral composite are investigated under varied temperatures in this study. The elastic modulus of the composite is determined from the natural frequency of composite specimens at different temperatures by using a damping monitoring method. Then, the backside deformation of composite plates is analysed experimentally and numerically employing the finite-element program Abaqus. The experimental and numeric results obtained are in good agreement.

  11. Tissue biocompatibility of kevlar aramid fibers and polymethylmethacrylate, composites in rabbits.

    Science.gov (United States)

    Henderson, J D; Mullarky, R H; Ryan, D E

    1987-01-01

    Two groups of female NZW rabbits were implanted in the paravertebral muscles with aramid (du Pont Kevlar aramid 49) fibers and aramid-polymethylmethacrylate (PMMA) composites for 14 and 28 days. Rabbits were killed at these times periods, necropsies performed, sites scored for gross tissue response, and tissue specimens containing the implants removed for histopathological evaluation. A mild fibrous tissue reaction was observed around all implants containing aramid fiber similar to that observed around the silicone control implant. Some foreign body giant cells were also present adjacent to the fibers. An intense necrotic inflammatory reaction was present around the positive control material (PVC Y-78). The tissue response to implantation of aramid fiber and fiber-PMMA composites indicates that aramid is a biocompatible material.

  12. Moisture dependence of positron lifetime in Kevlar-49

    Science.gov (United States)

    Singh, Jag J.; Holt, William H.; Mock, Willis, Jr.

    1984-01-01

    Because of filamentary character of Kevlar-49 aramid fibers, there is some concern about the moisture uptake and its effect on plastic composites reinforced with Kevlar-49 fibers. As part of continuing studies of positron lifetime in polymers, we have measured positron lifetime spectra in Kevlar-49 fibers as a function of their moisture content. The long lifetime component intensities are rather low, being only of the order of 2-3 percent. The measured values of long component lifetimes at various moisture levels in the specimens are as follows: 2072 +/- 173 ps (dry); 2013 +/- 193 ps (20.7 percent saturation); 1665 +/- 85 ps (25.7 percent saturation); 1745 +/- 257 ps (32.1 percent saturation); and 1772 +/- 217 ps (100 percent saturation). It is apparent that the long component lifetime at first decreases and then increases as the specimen moisture content increases. These results have been compared with those inferred from Epon-815 and Epon-815/K-49 composite data.

  13. Multi-response parametric optimization in drilling of bamboo/Kevlar fiber reinforced sandwich composite

    Science.gov (United States)

    Singh, Thingujam Jackson; Samanta, Sutanu

    2016-09-01

    In the present work an attempt was made towards parametric optimization of drilling bamboo/Kevlar K29 fiber reinforced sandwich composite to minimize the delamination occurred during the drilling process and also to maximize the tensile strength of the drilled composite. The spindle speed and the feed rate of the drilling operation are taken as the input parameters. The influence of these parameters on delamination and tensile strength of the drilled composite studied and analysed using Taguchi GRA and ANOVA technique. The results show that both the response parameters i.e. delamination and tensile strength are more influenced by feed rate than spindle speed. The percentage contribution of feed rate and spindle speed on response parameters are 13.88% and 81.74% respectively.

  14. Investigation of Kevlar fabric-based materials for use with inflatable structures

    Science.gov (United States)

    Niccum, R. J.; Munson, J. B.; Rueter, L. L.

    1977-01-01

    Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported. The practicality of using Kevlar in aerostat materials is demonstrated, and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar-based materials are compared with conventional Dacron-reinforced counterparts. A comprehensive test and qualification program is discussed, and considerable quantitative biaxial tensile and shear test data are provided.

  15. Considerations for acoustic emission monitoring of spherical Kevlar/epoxy composite pressure vessels

    Science.gov (United States)

    Hamstad, M. A.; Patterson, R. G.

    1977-01-01

    We are continuing to research the applications of acoustic emission testing for predicting burst pressure of filament-wound Kevlar 49/epoxy pressure vessels. This study has focused on three specific areas. The first area involves development of an experimental technique and the proper instrumentation to measure the energy given off by the acoustic emission transducer per acoustic emission burst. The second area concerns the design of a test fixture in which to mount the composite vessel so that the acoustic emission transducers are held against the outer surface of the composite. Included in this study area is the calibration of the entire test setup including couplant, transducer, electronics, and the instrument measuring the energy per burst. In the third and final area of this study, we consider the number, location, and sensitivity of the acoustic emission transducers used for proof testing composite pressure vessels.

  16. Investigation of Kevlar fabric based materials for use with inflatable structures

    Science.gov (United States)

    Niccum, R. J.; Munson, J. B.

    1974-01-01

    Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported in detail. The practicality of using Kevlar in aerostat materials is demonstrated and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar based materials are compared with conventional, Dacron reinforced counterparts. A comprehensive test and qualification program is discussed and quantitative biaxial tensile and shear test data are provided. The investigation shows that single ply laminates of Kevlar and plastic films offer significant strength to weight improvements, are less permeable than two ply coated materials, but have a lower flex life.

  17. Interfacial characteristics of an epoxy composite reinforced with phosphoric acid-functionalized Kevlar fibers

    Science.gov (United States)

    Li, J.; Xia, Y. C.

    2010-07-01

    A Kevlar fiber was functionalized with the phosphoric acid (PA) of different concentrations. The surface characteristics of the fiber were examined by using the X-ray photoelectron spectroscopy. It was found that the PA functionalization considerably increased the bond strength between the Kevlar fiber and an epoxy matrix.

  18. An investigation of the compressive strength of Kevlar 49/epoxy composites

    Science.gov (United States)

    Kulkarni, S. V.; Rosen, B. W.; Rice, J. S.

    1975-01-01

    Tests were performed to evaluate the effect of a wide range of variables including matrix properties, interface properties, fiber prestressing, secondary reinforcement, and others on the ultimate compressive strength of Kevlar 49/epoxy composites. Scanning electron microscopy is used to assess the resulting failure surfaces. In addition, a theoretical study is conducted to determine the influence of fiber anisotropy and lack of perfect bond between fiber and matrix on the shear mode microbuckling. The experimental evaluation of the effect of various constituent and process characteristics on the behavior of these unidirectional composites in compression did not reveal any substantial increase in strength. However, theoretical evaluations indicate that the high degree of fiber anisotropy results in a significant drop in the predicted stress level for internal instability. Scanning electron microscope data analysis suggests that internal fiber failure and smooth surface debonding could be responsible for the measured low compressive strengths.

  19. Detonation nanodiamonds for doping Kevlar.

    Science.gov (United States)

    Comet, Marc; Pichot, Vincent; Siegert, Benny; Britz, Fabienne; Spitzer, Denis

    2010-07-01

    This paper reports on the first attempt to enclose diamond nanoparticles--produced by detonation--into a Kevlar matrix. A nanocomposite material (40 wt% diamond) was prepared by precipitation from an acidic solution of Kevlar containing dispersed nanodiamonds. In this material, the diamond nanoparticles (Ø = 4 nm) are entirely wrapped in a Kevlar layer about 1 nm thick. In order to understand the interactions between the nanodiamond surface and the polymer, the oxygenated surface functional groups of nanodiamond were identified and titrated by Boehm's method which revealed the exclusive presence of carboxyl groups (0.85 sites per nm2). The hydrogen interactions between these groups and the amide groups of Kevlar destroy the "rod-like" structure and the classical three-dimensional organization of this polymer. The distortion of Kevlar macromolecules allows the wrapping of nanodiamonds and leads to submicrometric assemblies, giving a cauliflower structure reminding a fractal object. Due to this structure, the macroscopic hardness of Kevlar doped by nanodiamonds (1.03 GPa) is smaller than the one of pure Kevlar (2.31 GPa). To our knowledge, this result is the first illustration of the change of the mechanical properties induced by doping the Kevlar with nanoparticles.

  20. Etude comparative sur la propagation de l'endommagement apres impact des composites carbone/epoxy renforces par piquage au fil Kevlar et titane-nickel

    Science.gov (United States)

    Vachon, Pierre-Luc

    Composite laminates have strong in-plane mechanical properties, but they are generally weaker through their thickness. This specificity makes the laminates prone to delamination, particularly under low-velocity impact loads. Consequently numerous research efforts have been dedicated to developing interlaminar reinforcing methods, such as transverse stitching. The present project proposes the use of the stitching technique combined with a special stitching thread made of superelastic TiNi alloy. This technology is intended to improve the delamination toughness in composite laminates loaded in bending. In the first part of this study a numerical model was developed for analyzing composite structures. The 3-D finite element model was built with the ANSYS commercial software using 20-node solid and 8-node shell elements. The progressive damage modeling technique was used, allowing the prediction of delamination propagation in a laminate submitted to various loading modes. The model was validated for a plate under quasi-static traction load, and it was then used to simulate three-point bending tests. Secondly, carbon/epoxy composite panels were fabricated, with each panel containing unstitched and stitched specimens. Two different materials were used for the stitching thread: superelastic TiNi wires and Kevlar threads as a reference. Some stitched specimens were cut in slices in order to make some observations of the internal stitch using an optical microscope. Standardized low-velocity impact tests and compression after impact tests were carried out on stitched and unstitched specimens (ASTM D7136 and D7137). The Kevlar reinforcements have shown great performance in reducing the delaminated zone after impact, as well as in improving the residual compression strength. The TiNi reinforcements provided encouraging results during the impact tests, though being less effective than the Kevlar threads. During the compression after impact tests, only a slight difference could

  1. Kevlar/PMR-15 polyimide matrix composite for a complex shaped DC-9 drag reduction fairing

    Science.gov (United States)

    Kawai, R. T.; Mccarthy, R. F.; Willer, M. S.; Hrach, F. J.

    1982-01-01

    The Aircraft Energy Efficiency (ACEE) Program was established by NASA to improve the fuel efficiency of commercial transport aircraft and thereby to reduce the amount of fuel consumed by the air transportation industry. One of the final items developed by the program is an improved fairing which is the aft closure for the thrust reverser actuators on the JT8D nacelles on DC-9 aircraft. The reduced-drag fairing uses, in the interest of weight savings, an advanced composite construction. The composite material contains Kevlar 49 fibers in a PMR-15 matrix. Attention is given to the aerodynamic configuration, the material system, and aspects of fabrication development.

  2. Lightweight engine containment. [Kevlar shielding

    Science.gov (United States)

    Weaver, A. T.

    1977-01-01

    Kevlar fabric styles and weaves were studied, as well as methods of application for advanced gas turbine engines. The Kevlar material was subjected to high speed impacts by simple projectiles fired from a rifle, as well as more complex shapes such as fan blades released from gas turbine rotors in a spin pit. Just contained data was developed for a variety of weave and/or application techniques, and a comparative containment weight efficiency was established for Kevlar containment applications. The data generated during these tests is being incorporated into an analytical design system so that blade containment trade-off studies between Kevlar and metal case engine structures can be made. Laboratory tests and engine environment tests were performed to determine the survivability of Kevlar in a gas turbine environment.

  3. Effect of Coconut Fillers on Hybrid Coconut Kevlar Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    S. P. Jani

    2015-12-01

    Full Text Available This project focuses on the conversion of naturally available coconut fibers and shells into a useful composite. In addition to it, some mechanical properties of the resultant composite is determined and also the effect of coconut shell fillers on the composite is also investigated. The few portion of the composite is incorporated with synthetic Kevlar fiber, thus the coconut fiber is hybridized to enhance the mechanical properties of coconut. In this work two types of composite is fabricate, kevelar coconut fibre (kc composite and kevelarcoco nut fibre coconut shell filler (kccsf composite. Coconut fibers have low weight and considerable properties among the natural fibers, while coconut fillers have a good ductile and impact property. The natural fibers and fillers are treated with Na-OH to make it free of organic impurities. Epoxy resin is used as the polymer matrix. Two composite are produced one with fillers and the other without the fillers using compression molding method. Mechanical properties like tensile strength, flexural strength and water absorption tests are done with ASTM standard. It is observed that that the addition of filler materials improves the adhesiveness of the fibers leading to the increase in the above mentioned properties. The density of the composite is also low hence the strength to weight ratio is very high. The water absorption test also showed that the resultant composite had a small adhesion to water and absorption of water.

  4. Studying Some of Electrical and Mechanical Properties for Kevlar Fiber Reinforced Epoxy

    Science.gov (United States)

    Rafeeq, Sewench N.; Hussein, Samah M.

    2011-12-01

    As ordinary known the ability of synthesizing electrical conducting polymer composites is possible but with poor mechanical properties, for the solution of this problem, we carried out this study in order to obtain that both properties. Three methods were applied for preparing the conductive polyaniline (PANI) composites using Kevlar fiber fabric as substrate for the deposition of the PANI at one time and the prepared composite (EP/Kevlar fiber) at others. The chemical oxidative method was adopted for polymerization of the aniline and simultaneously protonated of PANI with a hydrochloric acid at concentration (1M). Two kinds of oxidation agents (FeCl3.6H2O) and ((NH4)2S2O8) were used. The electrical measurements indicate the effect of each preparation method, kind of oxidant agent and the kind of mat erial which PANI deposited on the electrical results. The conductivity results showed that the prepared composites lie within semiconductors region. Temperature—dependence of electric conductivity results showed semiconductors and conductors behavior of this material within the applied temperature ranges. The mechan ical property (tensile strength) was studied. X-ray diffraction study showed the crystalline structure for EP/Kevlar fiber/PANI composites prepared by the three methods. These results gave optimism to the synthesis of conductive polymer composites with excellent mechanical properties..

  5. Evaluation of Material Models within LS-DYNA(Registered TradeMark) for a Kevlar/Epoxy Composite Honeycomb

    Science.gov (United States)

    Polanco, Michael A.; Kellas, Sotiris; Jackson, Karen

    2009-01-01

    The performance of material models to simulate a novel composite honeycomb Deployable Energy Absorber (DEA) was evaluated using the nonlinear explicit dynamic finite element code LS-DYNA(Registered TradeMark). Prototypes of the DEA concept were manufactured using a Kevlar/Epoxy composite material in which the fibers are oriented at +/-45 degrees with respect to the loading axis. The development of the DEA has included laboratory tests at subcomponent and component levels such as three-point bend testing of single hexagonal cells, dynamic crush testing of single multi-cell components, and impact testing of a full-scale fuselage section fitted with a system of DEA components onto multi-terrain environments. Due to the thin nature of the cell walls, the DEA was modeled using shell elements. In an attempt to simulate the dynamic response of the DEA, it was first represented using *MAT_LAMINATED_COMPOSITE_FABRIC, or *MAT_58, in LS-DYNA. Values for each parameter within the material model were generated such that an in-plane isotropic configuration for the DEA material was assumed. Analytical predictions showed that the load-deflection behavior of a single-cell during three-point bending was within the range of test data, but predicted the DEA crush response to be very stiff. In addition, a *MAT_PIECEWISE_LINEAR_PLASTICITY, or *MAT_24, material model in LS-DYNA was developed, which represented the Kevlar/Epoxy composite as an isotropic elastic-plastic material with input from +/-45 degrees tensile coupon data. The predicted crush response matched that of the test and localized folding patterns of the DEA were captured under compression, but the model failed to predict the single-cell three-point bending response.

  6. Wear Process Analysis of the Polytetrafluoroethylene/Kevlar Twill Fabric Based on the Components’ Distribution Characteristics

    Directory of Open Access Journals (Sweden)

    Gu Dapeng

    2017-12-01

    Full Text Available Polytetrafluoroethylene (PTFE/Kevlar fabric or fabric composites with excellent tribological properties have been considered as important materials used in bearings and bushing, for years. The components’ (PTFE, Kevlar, and the gap between PTFE and Kevlar distribution of the PTFE/Kevlar fabric is uneven due to the textile structure controlling the wear process and behavior. The components’ area ratio on the worn surface varying with the wear depth was analyzed not only by the wear experiment, but also by the theoretical calculations with our previous wear geometry model. The wear process and behavior of the PTFE/Kevlar twill fabric were investigated under dry sliding conditions against AISI 1045 steel by using a ring-on-plate tribometer. The morphologies of the worn surface were observed by the confocal laser scanning microscopy (CLSM. The wear process of the PTFE/Kevlar twill fabric was divided into five layers according to the distribution characteristics of Kevlar. It showed that the friction coefficients and wear rates changed with the wear depth, the order of the antiwear performance of the previous three layers was Layer III>Layer II>Layer I due to the area ratio variation of PTFE and Kevlar with the wear depth.

  7. Kevlar ve S-Cam ile Güçlendirilmiş HibritKompozitlerin Titreşim Özelliklerinin Belirlenmesi

    OpenAIRE

    Bulut, Mehmet; Erkliğ, Ahmet; Yeter, Eyüp

    2015-01-01

    In this study, it is aimed to investigate the vibration characteristics of hybrid and non-hybrid composite laminates reinforced with Kevlar and S-glass fibers. For this purpose, different ratios of Kevlar/S-glass-epoxy hybrid and non-hybrid composite laminates were prepared, their vibration responses were identified and results were compared with each other. In addition, finite element method using ANSYS software, the effects of fiber orientation angle on natural frequency of the composite la...

  8. Tension-Compression Fatigue Behavior of Plain Woven Kenaf/Kevlar Hybrid Composites

    Directory of Open Access Journals (Sweden)

    Suhad D. Salman

    2016-02-01

    Full Text Available The applications of hybrid natural/synthetic reinforced polymer composites have been rapidly gaining market share in structural applications due to their remarkable characteristics and the fact that most of the components made of these materials are subjected to cyclic loading. Their fatigue properties have received a lot of attention because predicting their behavior is a challenge due to the effects of the synergies between the fibers. The purpose of this work is to characterize the tension, compression, and tensile-compression fatigue behavior of six layers of Kevlar hybridized with one layer of woven kenaf reinforced epoxy, at a 35% weight fraction. Fatigue tests were carried out and loaded cyclically at 60%, 70%, 80%, and 90% of their ultimate compressive stress. The results give a complete description for tensile and compression properties and could be used to predict fatigue-induced failure mechanisms.

  9. In-Situ NDE Characterization of Kevlar and Carbon Composite Micromechanics for Improved COPV Health Monitoring

    Science.gov (United States)

    Waller, Jess M.; Saulsberry, Regor L.

    2009-01-01

    This project is a subtask of a multi-center project to advance the state-of-the-art by developing NDE techniques that are capable of evaluating stress rupture (SR) degradation in Kevlar/epoxy (K/Ep) composite overwrapped pressure vessels (COPVs), and damage progression in carbon/epoxy (C/Ep) COPVs. In this subtask, acoustic emission (AE) data acquired during intermittent load hold tensile testing of K/Ep and C/Ep composite tow materials-of-construction used in COPV fabrication were analyzed to monitor progressive damage during the approach to tensile failure. Insight into the progressive damage of composite tow was gained by monitoring AE event rate, energy, source location, and frequency. Source location based on arrival time data was used to discern between significant AE attributable to microstructural damage and spurious AE attributable to background and grip noise. One of the significant findings was the observation of increasing violation of the Kaiser effect (Felicity ratio < 1.0) with damage accumulation.

  10. Use of Acoustic Emission to Monitor Progressive Damage Accumulation in Kevlar (R) 49 Composites

    Science.gov (United States)

    Waller, Jess M.; Saulsberry, Regor L.; Andrade, Eduardo

    2009-01-01

    Acoustic emission (AE) data acquired during intermittent load hold tensile testing of epoxy impregnated Kevlar(Registeres TradeMark) 49 (K/Ep) composite strands were analyzed to monitor progressive damage during the approach to tensile failure. Insight into the progressive damage of K/Ep strands was gained by monitoring AE event rate and energy. Source location based on energy attenuation and arrival time data was used to discern between significant AE attributable to microstructural damage and spurious AE attributable to noise. One of the significant findings was the observation of increasing violation of the Kaiser effect (Felicity ratio < 1.0) with damage accumulation. The efficacy of three different intermittent load hold stress schedules that allowed the Felicity ratio to be determined analytically is discussed.

  11. Development of failure criterion for Kevlar-epoxy fabric laminates

    Science.gov (United States)

    Tennyson, R. C.; Elliott, W. G.

    1984-01-01

    The development of the tensor polynomial failure criterion for composite laminate analysis is discussed. In particular, emphasis is given to the fabrication and testing of Kevlar-49 fabric (Style 285)/Narmco 5208 Epoxy. The quadratic-failure criterion with F(12)=0 provides accurate estimates of failure stresses for the Kevlar/Epoxy investigated. The cubic failure criterion was re-cast into an operationally easier form, providing the engineer with design curves that can be applied to laminates fabricated from unidirectional prepregs. In the form presented no interaction strength tests are required, although recourse to the quadratic model and the principal strength parameters is necessary. However, insufficient test data exists at present to generalize this approach for all undirectional prepregs and its use must be restricted to the generic materials investigated to-date.

  12. Electron-beam-induced post-grafting polymerization of acrylic acid onto the surface of Kevlar fibers

    Science.gov (United States)

    Xu, Lu; Hu, Jiangtao; Ma, Hongjuan; Wu, Guozhong

    2018-04-01

    The surface of Kevlar fibers was successfully modified by electron beam (EB)-induced post-grafting of acrylic acid (AA). The generation of radicals in the fibers was confirmed by electron spin resonance (ESR) measurements, and the concentration of radicals was shown to increase as the absorbed dose increased, but decrease with increasing temperature. The influence of the synthesis conditions on the degree of grafting was also investigated. The surface microstructure and chemical composition of the modified Kevlar fibers were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The SEM images revealed that the surface of the grafted fibers was rougher than those of the pristine and irradiated fibers. XPS analysis confirmed an increase in C(O)OH groups on the surface of the Kevlar fibers, suggesting successful grafting of AA. These results indicate that EB-induced post-grafting polymerization is effective for modifying the surface properties of Kevlar fibers.

  13. Experimental Determination of Ballistic Performance of Composite Material Kevlar 29 and Alumina Powder/ Epoxy by Spherical Projectile

    Directory of Open Access Journals (Sweden)

    Luay Hashem Abbud

    2016-12-01

    Full Text Available In this study, a response of hybrid composite laminate woven fiber Kevlar29 – Al2O3 Powder/ Epoxy subjected to high velocity impact loading is presented. The energy absorbed due to impact of small rigid projectile on composite materials targets is determined experimentally. The energy absorbed due to impact of hemispherical projectiles on the developed composite laminates is investigated. The results revealed the maximum ballistic limit at impact velocity is found to be 390.87 ± 6 m/s for an the 18 mm target thickness. The ballistic limit velocity predictions are based on the theoretical method presented from another article. The initial velocity and residual velocity results showed good is agreement compared with the predicted results of Ipson and Recht equations. With 5.4 % of accuracy based on the experimental value for the theoretical model for ballistic limit velocity.

  14. A Study of Aerodynamics in Kevlar-Wall Test Sections

    OpenAIRE

    Brown, Kenneth Alexander

    2014-01-01

    This study is undertaken to characterize the aerodynamic behavior of Kevlar-wall test sections and specifically those containing two-dimensional, lifting models. The performance of the Kevlar-wall test section can be evaluated against the standard of the hard-wall test section, which in the case of the Stability Wind Tunnel (SWT) at Virginia Tech can be alternately installed or replaced by the Kevlar-wall test section. As a first step towards the evaluation of the Kevlar-wall test section aer...

  15. Experimental analysis of graphene nanocomposite on Kevlar

    Science.gov (United States)

    Manigandan, S.; Gunasekar, P.; Nithya, S.; Durga Revanth, G.; Anudeep, A. V. S. C.

    2017-08-01

    Graphene nanocomposite is a two dimensional structure which has intense role in material science. This paper investigates the topological property of the graphene nanocomposite doped in Kevlar fiber by direct mixing process. The Kevlar fiber by direct mixing process. The Kevlar fiber taken as the specimen which is fabricated by vacuum bag moulding process. Epoxy used as resin and HY951 as hardener. Three different specimens are fabricated based on the percentage of graphene nanocomposite 2%, 5%, 10% and 20% respectively. We witnessed the strength of the Kevlar fiber is increased when it is treated with nanocomposite. The percentage of the nanocomposite increase the strength of the fiber is increased. However as the nanocomposite beyond 5% the strength of fiber is dropped. In addition, we also seen the interfacial property of the fiber is dropped when the nanocomposite is added beyond threshold limit.

  16. Experimental and analytical study of high velocity impact on Kevlar/Epoxy composite plates

    Science.gov (United States)

    Sikarwar, Rahul S.; Velmurugan, Raman; Madhu, Velmuri

    2012-12-01

    In the present study, impact behavior of Kevlar/Epoxy composite plates has been carried out experimentally by considering different thicknesses and lay-up sequences and compared with analytical results. The effect of thickness, lay-up sequence on energy absorbing capacity has been studied for high velocity impact. Four lay-up sequences and four thickness values have been considered. Initial velocities and residual velocities are measured experimentally to calculate the energy absorbing capacity of laminates. Residual velocity of projectile and energy absorbed by laminates are calculated analytically. The results obtained from analytical study are found to be in good agreement with experimental results. It is observed from the study that 0/90 lay-up sequence is most effective for impact resistance. Delamination area is maximum on the back side of the plate for all thickness values and lay-up sequences. The delamination area on the back is maximum for 0/90/45/-45 laminates compared to other lay-up sequences.

  17. Robust Tensioned Kevlar Suspension Design

    Science.gov (United States)

    Young, Joseph B.; Naylor, Bret J.; Holmes, Warren A.

    2012-01-01

    One common but challenging problem in cryogenic engineering is to produce a mount that has excellent thermal isolation but is also rigid. Such mounts can be achieved by suspending the load from a network of fibers or strings held in tension. Kevlar fibers are often used for this purpose owing to their high strength and low thermal conductivity. A suite of compact design elements has been developed to improve the reliability of suspension systems made of Kevlar.

  18. Carbon nanotube and graphene nanoribbon-coated conductive Kevlar fibers.

    Science.gov (United States)

    Xiang, Changsheng; Lu, Wei; Zhu, Yu; Sun, Zhengzong; Yan, Zheng; Hwang, Chi-Chau; Tour, James M

    2012-01-01

    Conductive carbon material-coated Kevlar fibers were fabricated through layer-by-layer spray coating. Polyurethane was used as the interlayer between the Kevlar fiber and carbon materials to bind the carbon materials to the Kevlar fiber. Strongly adhering single-walled carbon nanotube coatings yielded a durable conductivity of 65 S/cm without significant mechanical degradation. In addition, the properties remained stable after bending or water washing cycles. The coated fibers were analyzed using scanning electron microcopy and a knot test. The as-produced fiber had a knot efficiency of 23%, which is more than four times higher than that of carbon fibers. The spray-coating of graphene nanoribbons onto Kevlar fibers was also investigated. These flexible coated-Kevlar fibers have the potential to be used for conductive wires in wearable electronics and battery-heated armors. © 2011 American Chemical Society

  19. Biomimetic Hybridization of Kevlar into Silk Fibroin: Nanofibrous Strategy for Improved Mechanic Properties of Flexible Composites and Filtration Membranes.

    Science.gov (United States)

    Lv, Lili; Han, Xiangsheng; Zong, Lu; Li, Mingjie; You, Jun; Wu, Xiaochen; Li, Chaoxu

    2017-08-22

    Silk, one of the strongest natural biopolymers, was hybridized with Kevlar, one of the strongest synthetic polymers, through a biomimetic nanofibrous strategy. Regenerated silk materials have outstanding properties in transparency, biocompatibility, biodegradability and sustainability, and promising applications as diverse as in pharmaceutics, electronics, photonic devices and membranes. To compete with super mechanic properties of their natural counterpart, regenerated silk materials have been hybridized with inorganic fillers such as graphene and carbon nanotubes, but frequently lose essential mechanic flexibility. Inspired by the nanofibrous strategy of natural biomaterials (e.g., silk fibers, hemp and byssal threads of mussels) for fantastic mechanic properties, Kevlar was integrated in regenerated silk materials by combining nanometric fibrillation with proper hydrothermal treatments. The resultant hybrid films showed an ultimate stress and Young's modulus two times as high as those of pure regenerated SF films. This is not only because of the reinforcing effect of Kevlar nanofibrils, but also because of the increasing content of silk β-sheets. When introducing Kevlar nanofibrils into the membranes of silk nanofibrils assembled by regenerated silk fibroin, the improved mechanic properties further enabled potential applications as pressure-driven nanofiltration membranes and flexible substrates of electronic devices.

  20. Evaluation of Acoustic Emission NDE of Kevlar Composite Over Wrapped Pressure Vessels

    Science.gov (United States)

    Horne, Michael R.; Madaras, Eric I.

    2008-01-01

    Pressurization and failure tests of small Kevlar/epoxy COPV bottles were conducted during 2006 and 2007 by Texas Research Institute Austin, Inc., at TRI facilities. This is a report of the analysis of the Acoustic Emission (AE) data collected during those tests. Results of some of the tests indicate a possibility that AE can be used to track the stress-rupture degradation of COPV vessels.

  1. Impact behavior of f-silica and amine terminated polybutadiene co-acrylonitrile rubber modified novolac epoxy/Kevlar nanocomposites

    Science.gov (United States)

    Kavita, Pal, Vijayeta; Tiwari, R. K.

    2018-05-01

    In the present work, nano-fumed silica treated with 3-Glycidoxypropyl trimethoxy silane (f-silica) was used as a nanoreinforcement in the fabrication of amine terminated polybutadiene co-acrylonitrile rubber (ATBN) modified Kevlar/epoxy based nanocomposites. Nanocomposites with different f-silica loading (0, 0.5, 1.0 and 2.0 wt. %) and having same ATBN (10 wt. %) were made and characterized by Izod impact test for evaluating impact strength values. All the nanocomposites showed better impact strength than neat Kevlar/novolac epoxy based composite.

  2. Hybrid composite laminates reinforced with Kevlar/carbon/glass woven fabrics for ballistic impact testing.

    Science.gov (United States)

    Randjbaran, Elias; Zahari, Rizal; Jalil, Nawal Aswan Abdul; Majid, Dayang Laila Abang Abdul

    2014-01-01

    Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers.

  3. Hybrid Composite Laminates Reinforced with Kevlar/Carbon/Glass Woven Fabrics for Ballistic Impact Testing

    Directory of Open Access Journals (Sweden)

    Elias Randjbaran

    2014-01-01

    Full Text Available Current study reported a facile method to investigate the effects of stacking sequence layers of hybrid composite materials on ballistic energy absorption by running the ballistic test at the high velocity ballistic impact conditions. The velocity and absorbed energy were accordingly calculated as well. The specimens were fabricated from Kevlar, carbon, and glass woven fabrics and resin and were experimentally investigated under impact conditions. All the specimens possessed equal mass, shape, and density; nevertheless, the layers were ordered in different stacking sequence. After running the ballistic test at the same conditions, the final velocities of the cylindrical AISI 4340 Steel pellet showed how much energy was absorbed by the samples. The energy absorption of each sample through the ballistic impact was calculated; accordingly, the proper ballistic impact resistance materials could be found by conducting the test. This paper can be further studied in order to characterise the material properties for the different layers.

  4. Experimental analysis of Kevlar modification for TRUPACT-I puncture panels

    International Nuclear Information System (INIS)

    Longenbaugh, R.S.; Joseph, B.J.

    1987-05-01

    The Kevlar Test Services was initiated to determine the maximum failure force and the energy-absorbing capability of puncture panels consisting of 16, 20, and 24 layers of 3000-denier 4 x 4 basket weave Kevlar-29, bonded to a 3.41 mm 304 annealed stainless steel puncture plate. Results of these tests were compared to the TRUPACT-1 Unit-0 drop test results to determine if the existing puncture panel configuration of TRUPACT-1 could be reduced. The data indicate for 24 layers of Kevlar, the panels failed at loads greater than those recorded in the TRUPACT-1, Unit 0 tests. Energy absorbed by the 24-layer Kevlar panels was 53% greater than that measured in the TRUPACT-1, Unit 0 test. Thermal performance of 20-layer Kevlar panels was measured in a conservative test environment and exceeded the design specifications

  5. Microwave-synthesized freestanding iron-carbon nanotubes on polyester composites of woven Kevlar fibre and silver nanoparticle-decorated graphene

    Science.gov (United States)

    Hazarika, Ankita; Deka, Biplab K.; Kim, DoYoung; Kong, Kyungil; Park, Young-Bin; Park, Hyung Wook

    2017-01-01

    We synthesized Ag nanoparticle-decorated multilayered graphene nanosheets (Ag-graphene) from graphite nanoplatelets and silver nitrate through 90–100 s of microwave exposure, without the use of any mineral acids or harsh reducing agents. Fe nanoparticle-decorated carbon nanotubes (Fe-CNTs) were grown on polypyrrole (PPy) deposited on woven Kevlar fibre (WKF), using ferrocene as a catalyst, under microwave irradiation. Fe-CNTs grown on WKF and Ag-graphene dispersed in polyester resin (PES) were combined to fabricate Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites by vacuum-assisted resin transfer moulding. The combined effect of Fe-CNTs and Ag-graphene in the resulting composites resulted in a remarkable enhancement of tensile properties (a 192.56% increase in strength and 100.64% increase in modulus) as well as impact resistance (a 116.33% increase). The electrical conductivity significantly increased for Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites. The effectiveness of electromagnetic interference shielding, which relies strongly on the Ag-graphene content in the composites, was 25 times higher in Ag-graphene/Fe-CNT/PPy-coated WKF/PES than in neat WKF/PES composites. The current work offers a novel route for fabricating highly promising, cost effective WKF/PES composites through microwave-assisted synthesis of Fe-CNTs and Ag-graphene. PMID:28074877

  6. Microwave-synthesized freestanding iron-carbon nanotubes on polyester composites of woven Kevlar fibre and silver nanoparticle-decorated graphene.

    Science.gov (United States)

    Hazarika, Ankita; Deka, Biplab K; Kim, DoYoung; Kong, Kyungil; Park, Young-Bin; Park, Hyung Wook

    2017-01-11

    We synthesized Ag nanoparticle-decorated multilayered graphene nanosheets (Ag-graphene) from graphite nanoplatelets and silver nitrate through 90-100 s of microwave exposure, without the use of any mineral acids or harsh reducing agents. Fe nanoparticle-decorated carbon nanotubes (Fe-CNTs) were grown on polypyrrole (PPy) deposited on woven Kevlar fibre (WKF), using ferrocene as a catalyst, under microwave irradiation. Fe-CNTs grown on WKF and Ag-graphene dispersed in polyester resin (PES) were combined to fabricate Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites by vacuum-assisted resin transfer moulding. The combined effect of Fe-CNTs and Ag-graphene in the resulting composites resulted in a remarkable enhancement of tensile properties (a 192.56% increase in strength and 100.64% increase in modulus) as well as impact resistance (a 116.33% increase). The electrical conductivity significantly increased for Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites. The effectiveness of electromagnetic interference shielding, which relies strongly on the Ag-graphene content in the composites, was 25 times higher in Ag-graphene/Fe-CNT/PPy-coated WKF/PES than in neat WKF/PES composites. The current work offers a novel route for fabricating highly promising, cost effective WKF/PES composites through microwave-assisted synthesis of Fe-CNTs and Ag-graphene.

  7. Microwave-synthesized freestanding iron-carbon nanotubes on polyester composites of woven Kevlar fibre and silver nanoparticle-decorated graphene

    Science.gov (United States)

    Hazarika, Ankita; Deka, Biplab K.; Kim, Doyoung; Kong, Kyungil; Park, Young-Bin; Park, Hyung Wook

    2017-01-01

    We synthesized Ag nanoparticle-decorated multilayered graphene nanosheets (Ag-graphene) from graphite nanoplatelets and silver nitrate through 90-100 s of microwave exposure, without the use of any mineral acids or harsh reducing agents. Fe nanoparticle-decorated carbon nanotubes (Fe-CNTs) were grown on polypyrrole (PPy) deposited on woven Kevlar fibre (WKF), using ferrocene as a catalyst, under microwave irradiation. Fe-CNTs grown on WKF and Ag-graphene dispersed in polyester resin (PES) were combined to fabricate Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites by vacuum-assisted resin transfer moulding. The combined effect of Fe-CNTs and Ag-graphene in the resulting composites resulted in a remarkable enhancement of tensile properties (a 192.56% increase in strength and 100.64% increase in modulus) as well as impact resistance (a 116.33% increase). The electrical conductivity significantly increased for Ag-graphene/Fe-CNT/PPy-coated WKF/PES composites. The effectiveness of electromagnetic interference shielding, which relies strongly on the Ag-graphene content in the composites, was 25 times higher in Ag-graphene/Fe-CNT/PPy-coated WKF/PES than in neat WKF/PES composites. The current work offers a novel route for fabricating highly promising, cost effective WKF/PES composites through microwave-assisted synthesis of Fe-CNTs and Ag-graphene.

  8. PA6 and Kevlar fiber reinforced isotactic polypropylene: Structure, mechanical properties and crystallization and melting behavior

    International Nuclear Information System (INIS)

    Zhao, Songfang; Cheng, Lei; Guo, Yong; Zheng, Yuying; Li, Baoming

    2012-01-01

    Highlights: ► KF was modified with caprolactam using toluenediisocyanate (TDI) as bridge. ► Modified KF improves interfacial interaction of iPP/KF/PA6 composites. ► Fiber and nylon 6 inhibited the crystallization of PP continuous phase. -- Abstract: To improve the thermal and mechanical properties of isotactic polypropylene (iPP), iPP/Kevlar fiber (KF)/polyamide 6 (PA6) composites were prepared via the melt-extrusion method on twin-screw extruder. Kevlar fiber was modified with caprolactam using toluenediisocyanate (TDI) as bridge. The microstructure of modified KF was successfully characterized by Fourier transform infrared (FT-IR), X-ray photoelectron spectrometer (XPS) and scanning electron microscopy (SEM), the results showed that KF was bonded with caprolactam and became coarser. Then the modified KF was introduced into iPP, the composites have better mechanical and thermal properties, implying that modification of KF was helpful to improve the interfacial interaction of iPP/KF/PA6 composites. Besides, the crystallization curves indicated that crystallization behavior of PA6 in the composites was homogeneous and fractional. Furthermore, compatibilizer content played an important role in the mechanical and thermal properties of composites.

  9. Feasibility of Kevlar 49/PMR-15 polyimide for high temperature applications

    Science.gov (United States)

    Hanson, M. P.

    1980-01-01

    Kevlar 49 aramid organic fiber reinforced PMR-15 polyimide laminates were characterized to determine the applicability of the material to high temperature aerospace structures. Kevlar 49/3501-6 epoxy laminates were fabricated and characterized for comparison with the Kevlar 49/PMR-15 polyimide material. Flexural strengths and moduli and interlaminar shear strengths were determined from 75 to 600 F for the PMR-15 and from 75 to 450 F for the Kevlar 49/3501-6 epoxy material. The study also included the effects of hydrothermal and long-term elevated temperature exposures on the flexural strengths and moduli and the interlaminar shear strengths.

  10. Kevlar support for thermal isolation at low temperatures

    Science.gov (United States)

    Roach, Pat R.

    1992-01-01

    A cryogenic support is developed that rigidly attaches two U-shaped aluminum beams to each other with strands of Kevlar. The Kevlar creates a very strong and stiff coupling between the beams while allowing only very minor heat flow between them. Measurements at room temperature and at 77 K confirm the stiffness and strength of the support.

  11. Mallow Fiber-Reinforced Epoxy Composites in Multilayered Armor for Personal Ballistic Protection

    Science.gov (United States)

    Nascimento, Lucio Fábio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Lima, Édio Pereira; da Luz, Fernanda Santos

    2017-10-01

    Lighter and less expensive polymer composites reinforced with natural fibers have been investigated as possible components of a multilayered armor system (MAS) for personal protection against high-velocity ammunition. Their ballistic performance was consistently found comparable with that of conventional Kevlar® synthetic aramid fiber. Among the numerous existing natural fibers with the potential for reinforcing polymer composites to replace Kevlar® in MAS, mallow fiber has not been fully investigated. Thus, the objective of this work is to evaluate the ballistic performance of epoxy composites reinforced with 30 vol.% of aligned mallow fibers as a second MAS layer backing a front ceramic plate. The results using high-velocity 7.62 ammunition show a similar indentation to a Kevlar® layer with the same thickness. An impedance matching calculation supports the similar ballistic performance of mallow fiber composite and Kevlar®. Reduced MAS costs associated with the mallow fiber composite are practical advantages over Kevlar®.

  12. Metal-organic framework superhydrophobic coating on Kevlar fabric with efficient drag reduction and wear resistance

    Science.gov (United States)

    Li, Deke; Guo, Zhiguang

    2018-06-01

    Superhydrophobic layers are extremely essential for protecting material surface in various applications. In this study, a stable superhydrophobic mixed matrix surface with a 152.2° contact angle can be fabricated through the technology of layer-by-layer hot-pressing (HoP), and then modified by 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) on the ZIF-8@Kevlar fabric surface. The morphology and chemical composition were analyzed by the means of SEM, XRD and FTIR. The obtained superhydrophobic coatings showed excellent antiwear performance and drag reduction under desired working conditions. Moreover, we successfully applied superhydrophobic F-ZIF-8@Kevlar fabric in the alcohol adsorbent with high removal capacity, and it can be reused for several times without serious efficiency loss.

  13. In-line Kevlar filters for microfiltration of transuranic-containing liquid streams.

    Science.gov (United States)

    Gonzales, G J; Beddingfield, D H; Lieberman, J L; Curtis, J M; Ficklin, A C

    1992-06-01

    The Department of Energy Rocky Flats Plant has numerous ongoing efforts to minimize the generation of residue and waste and to improve safety and health. Spent polypropylene liquid filters held for plutonium recovery, known as "residue," or as transuranic mixed waste contribute to storage capacity problems and create radiation safety and health considerations. An in-line process-liquid filter made of Kevlar polymer fiber has been evaluated for its potential to: (1) minimize filter residue, (2) recover economically viable quantities of plutonium, (3) minimize liquid storage tank and process-stream radioactivity, and (4) reduce potential personnel radiation exposure associated with these sources. Kevlar filters were rated to less than or equal to 1 mu nominal filtration and are capable of reducing undissolved plutonium particles to more than 10 times below the economic discard limit, however produced high back-pressures and are not yet acid resistant. Kevlar filters performed independent of loaded particles serving as a sieve. Polypropylene filters removed molybdenum particles at efficiencies equal to Kevlar filters only after loading molybdenum during recirculation events. Kevlars' high-efficiency microfiltration of process-liquid streams for the removal of actinides has the potential to reduce personnel radiation exposure by a factor of 6 or greater, while simultaneously achieving a reduction in the generation of filter residue and waste by a factor of 7. Insoluble plutonium may be recoverable from Kevlar filters by incineration.

  14. An Experimental Study of Circular Cutout Hole Effect of Kevlar/epoxy-Al2O3 Composite under Subjected to Quasi-Static Compressive and Tensile Loading

    Directory of Open Access Journals (Sweden)

    Ayad Abed Ramadhan

    2017-12-01

    Full Text Available This paper has presented an experimental study of quasi-static compressive and tensile loading of cutout hole specimens of Kevlar-29/epoxy-Al2O3 laminated composite. The experimental procedure hasbeen developed to study the performance of (50%, 55% and 60% volume fraction (vf and (0o/90o and +45o/-45o fiber orientation angle effects of these composites under quasi-static tensile and compressiveload using a servo-hydraulic testing machine. The study was concluded that the ultimate load capacity increases as volume fraction increases in tensile test. While, the maximum load bearing capacity increaseswith the decrease of volume fraction in compression test. Hence, from the results obtained it can have considered the 55% volume fraction of composite panels is a good value for tensile and compressionapplications.

  15. Drilling and boring of a tube in composite Kevlar-epoxy material

    International Nuclear Information System (INIS)

    Souverain, J.

    1984-01-01

    The search coils for the high-precision measurement of the magnetic field of the LEP magnets have to be carried on a support tube of high specific modulus, in order to maintain the accuracy required. An aromatic polyamide fibre (aramide), Kevlar 49, in an epoxy matrix was chosen as the most suitable material. However, the manufacture of the supports involves the drilling of holes with high precision, and initial trials in the ISR (LEP) workshop produced poor results. Special tools were then successfully designed and manufactured on the basis of an analysis of the difficulties encountered. This report presents the cutting principles adopted and demonstrates the results obtained in the final product. (orig.)

  16. A comparative study on the tensile and impact properties of Kevlar, carbon, and S-glass/epoxy composites reinforced with SiC particles

    Science.gov (United States)

    Bulut, Mehmet; Alsaadi, Mohamad; Erkliğ, Ahmet

    2018-02-01

    Present study compares the tensile and impact characteristics of Kevlar, carbon and glass fiber reinforced composites with addition of microscale silicon carbide (SiC) within the common matrix of epoxy. The variation of tensile and impact strength values was explored for different content of SiC in the epoxy resin by weight (0, 5, 10, 15 and 20 wt%). Resulting failure characteristics were identified by assisting Charpy impact tests. The influence of interfacial adhesion between particle and fiber/matrix on failure and tensile properties was discussed from obtained results and scanning electron microscopy (SEM) figures. It is concluded from results that the content of SiC particles, and fiber types used as reinforcement are major parameters those effecting on tensile and impact resistance of composites as a result of different interface strength properties between particle-matrix and particle-fiber.

  17. Multiscale modeling of interwoven Kevlar fibers based on random walk to predict yarn structural response

    Science.gov (United States)

    Recchia, Stephen

    Kevlar is the most common high-end plastic filament yarn used in body armor, tire reinforcement, and wear resistant applications. Kevlar is a trade name for an aramid fiber. These are fibers in which the chain molecules are highly oriented along the fiber axis, so the strength of the chemical bond can be exploited. The bulk material is extruded into filaments that are bound together into yarn, which may be chorded with other materials as in car tires, woven into a fabric, or layered in an epoxy to make composite panels. The high tensile strength to low weight ratio makes this material ideal for designs that decrease weight and inertia, such as automobile tires, body panels, and body armor. For designs that use Kevlar, increasing the strength, or tenacity, to weight ratio would improve performance or reduce cost of all products that are based on this material. This thesis computationally and experimentally investigates the tenacity and stiffness of Kevlar yarns with varying twist ratios. The test boundary conditions were replicated with a geometrically accurate finite element model, resulting in a customized code that can reproduce tortuous filaments in a yarn was developed. The solid model geometry capturing filament tortuosity was implemented through a random walk method of axial geometry creation. A finite element analysis successfully recreated the yarn strength and stiffness dependency observed during the tests. The physics applied in the finite element model was reproduced in an analytical equation that was able to predict the failure strength and strain dependency of twist ratio. The analytical solution can be employed to optimize yarn design for high strength applications.

  18. Fabrication and Synthesis of Highly Ordered Nickel Cobalt Sulfide Nanowire-Grown Woven Kevlar Fiber/Reduced Graphene Oxide/Polyester Composites.

    Science.gov (United States)

    Hazarika, Ankita; Deka, Biplab K; Kim, DoYoung; Roh, Hyung Doh; Park, Young-Bin; Park, Hyung Wook

    2017-10-18

    Well-aligned NiCo 2 S 4 nanowires, synthesized hydrothermally on the surface of woven Kevlar fiber (WKF), were used to fabricate composites with reduced graphene oxide (rGO) dispersed in polyester resin (PES) by means of vacuum-assisted resin transfer molding. The NiCo 2 S 4 nanowires were synthesized with three precursor concentrations. Nanowire growth was characterized using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. Hierarchical and high growth density of the nanowires led to exceptional mechanical properties of the composites. Compared with bare WKF/PES, the tensile strength and absorbed impact energy were enhanced by 96.2% and 92.3%, respectively, for WKF/NiCo 2 S 4 /rGO (1.5%)/PES. The synergistic effect of NiCo 2 S 4 nanowires and rGO in the fabricated composites improved the electrical conductivity of insulating WKF/PES composites, reducing the resistance to ∼10 3 Ω. Joule heating performance depended strongly on the precursor concentration of the nanowires and the presence of rGO in the composite. A maximum surface temperature of 163 °C was obtained under low-voltage (5 V) application. The Joule heating performance of the composites was demonstrated in a surface deicing experiment; we observed that 17 g of ice melted from the surface of the composite in 14 min under an applied voltage of 5 V at -28 °C. The excellent performance of WKF/NiCo 2 S 4 /rGO/PES composites shows great potential for aerospace structural applications requiring outstanding mechanical properties and Joule heating capability for deicing of surfaces.

  19. Radiation exposure reduction by use of Kevlar cassettes in the neonatal nursery

    International Nuclear Information System (INIS)

    Herman, M.W.; Mak, H.K.; Lachman, R.S.

    1987-01-01

    A study was performed to determine whether the use of Kevlar cassettes in the neonatal intensive care nursery would reduce radiation exposure to patients. The radiation dose to the neonates was measured by using thermoluminescent dosimeters. In addition, the attenuation of the Kevlar cassettes and the sensitivity of the film-screen combination were compared with the previously used system. The greatest radiation reduction using a mobile X-ray unit was 27%; based on sensitivity measurements, the theoretical reduction averaged 38%. The reduction in radiation exposure resulted from reduced attenuation by the Kevlar cassette

  20. Development of a Continuum Damage Mechanics Material Model of a Graphite-Kevlar(Registered Trademark) Hybrid Fabric for Simulating the Impact Response of Energy Absorbing Kevlar(Registered Trademark) Hybrid Fabric for Simulating the Impact Response of Energy Absorbing

    Science.gov (United States)

    Jackson, Karen E.; Fasanella, Edwin L.; Littell, Justin D.

    2017-01-01

    This paper describes the development of input properties for a continuum damage mechanics based material model, Mat 58, within LS-DYNA(Registered Trademark) to simulate the response of a graphite-Kevlar(Registered Trademark) hybrid plain weave fabric. A limited set of material characterization tests were performed on the hybrid graphite-Kevlar(Registered Trademark) fabric. Simple finite element models were executed in LS-DYNA(Registered Trademark) to simulate the material characterization tests and to verify the Mat 58 material model. Once verified, the Mat 58 model was used in finite element models of two composite energy absorbers: a conical-shaped design, designated the "conusoid," fabricated of four layers of hybrid graphite-Kevlar(Registered Trademark) fabric; and, a sinusoidal-shaped foam sandwich design, designated the "sinusoid," fabricated of the same hybrid fabric face sheets with a foam core. Dynamic crush tests were performed on components of the two energy absorbers, which were designed to limit average vertical accelerations to 25- to 40-g, to minimize peak crush loads, and to generate relatively long crush stroke values under dynamic loading conditions. Finite element models of the two energy absorbers utilized the Mat 58 model that had been verified through material characterization testing. Excellent predictions of the dynamic crushing response were obtained.

  1. Novel nanocomposite Kevlar fabric membranes: Fabrication characterization, and performance in oil/water separation

    Science.gov (United States)

    Karimnezhad, Hanieh; Rajabi, Laleh; Salehi, Ehsan; Derakhshan, Ali Ashraf; Azimi, Sara

    2014-02-01

    Nanocomposite membranes with hydrophilic surface were fabricated for separation of oil (n-hexane) from oil/water emulsion. Three different nanomaterials namely, para-aminobenzoate alumoxane (PAB-A), boehmite-epoxide and polycitrate alumoxane (PC-A) were coated on the Kevlar fabric (support), according to a three-step dip-coating protocol. FTIR, SEM, TEM, UV/vis spectrophotometer, and wettability analyses were used to characterize the composite membranes. The three coating layers interacted chemically with one another and also physically with the Kevlar fabric. Water uptake measurements indicated that the membrane is a hydrophilic one. SEM and TEM analyses showed the smooth surface of the composite membrane and three-dimensional dendrimeric hyper-branched structure of (PC-A), respectively. A dead-end filtration setup was applied to test the membranes performance under natural gravity force. Effect of pH as an important variable affecting separation process was investigated with the neutral pH provided the optimum condition for the separation. Oil rejection and permeate fluxes were also monitored. The optimum flux and rejection obtained, were 7392 (Lm-2 h-1) and 89.06% at pH 7, respectively. Fouling occurred as a gel layer on the membrane surface. The deposited oil droplets on the surface of the membrane were successfully washed away with satisfactory permeate flux recovery (FRR = 88.88% at neutral pH), using hot distilled water and acidic solution as eluents.

  2. Tendon cell outgrowth rates and morphology associated with kevlar-49.

    Science.gov (United States)

    Zimmerman, M; Gordon, K E

    1988-12-01

    A rat tendon cell model was used to evaluate the in vitro biocompatibility of kevlar-49. The cell response to kevlar was compared to carbon AS-4 and nylon sutures. Three trials were run and cell growth rates were statistically similar for all the materials tested. A separate experiment was conducted in which the same fiber materials were placed in the same Petri dish. Again, the rates were similar for each material. Finally, the cells were observed with a scanning electron microscope, and the three classic cell morphologies associated with this tendon cell model were observed. Also, cellular attachment to the fiber and cellular encapsulation of the fiber were identical for the three materials tested. Kevlar-49 proved to be comparable to carbon AS4 and nylon sutures in terms of cellular response and cell outgrowth rates.

  3. Bound water in Kevlar 49 fibers

    International Nuclear Information System (INIS)

    Garza, R.G.; Pruneda, C.O.; Morgan, R.J.

    1981-01-01

    From elemental analyses, thermogravimetric-mass spectroscopy studies and re-evaluation of previous water diffusion studies in Kevlar 49 fibers it is concluded that these fibers can contain two types of sorbed moisture. The fibers can absorb up to approx. 6 wt % loosely bound water with an activation energy for outgassing by desorption of 6 kcal/mole. This loosely bound water is a direct result of the presence of Na 2 SO 4 impurities and the perturbations they induce on the packing of the rod-like poly (p-phenylene terephthalamide) macromolecules. Kevlar 49 fibers also inherently contain up to 30 wt % additional water which is tightly bound within the crystal lattice. This water exhibits an activation energy for outgassing by diffusion of approx. 40 kcal/mole and is only evolved from the fiber in significant quantities at t > 350 0 C over a period of hours

  4. Performance of adhesives base on PU, Epoxy and silane in the Kevlar/alumina interface; Desempenho de adesivos a base de PU, epoxi e silano na interface Kevlar/alumina

    Energy Technology Data Exchange (ETDEWEB)

    Noronha, K.F.; Melo, F.C.L.; Lopes, C.M.A. [Divisao de Materiais, Instituto de Aeronautica e Espaco (IAE), Sao Jose dos Campos, SP (Brazil); Divisao de Engenharia Mecanica-Aeronautica, Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil)], e-mail: cmoniz@iae.cta.br

    2010-07-01

    Hybrid ceramic/polymer composites are used for ballistic protection due to the good high-velocity impact absorption properties. The choice of the proper adhesive used to bond ceramic and polymer layers is one of the major issues for hybrid armor development due to its influence in the ballistic resistance behaviour. This work presents an adhesion study in composites of aramid textile (Kevlar) and alumina. Adhesives of different chemical nature, based on polyurethane, epoxy and silane were evaluated. T-Peel test was performed for the interface characterization and the post- failure surfaces were examined by optical microscopy. In all samples the failure occurred at the interface. The silane-based adhesive showed no interaction with the polymer, while the PU hot melt adhesive presented the highest adhesion strengths. (author)

  5. Intricacies of Using Kevlar and Thermal Knives in a Deployable Release System: Issues and Solutions

    Science.gov (United States)

    Stewart, Alphonso C.; Hair, Jason H.; Broduer, Steve (Technical Monitor)

    2002-01-01

    The utilization of Kevlar cord and thermal knives in a deployable release system produces a number of issues that must be addressed in the design of the system. This paper proposes design considerations that minimize the major issues, thermal knife failure, Kevlar cord relaxation, and the measurement of the cord tension. Design practices can minimize the potential for thermal knife laminate and element damage that result in failure of the knife. A process for in-situ inspection of the knife with resistance, rather than continuity, checks and 10x zoom optical imaging can detect damaged knives. Tests allow the characterization of the behavior of the particular Kevlar cord in use and the development of specific pre-stretching techniques and initial tension values needed to meet requirements. A new method can accurately measure the tension of the Kevlar cord using a guitar tuner, because more conventional methods do not apply to arimid cords such as Kevlar.

  6. X-ray diffraction and mechanical properties studies on Kevlar-49 fibres

    International Nuclear Information System (INIS)

    Abdo, S. M.

    1988-01-01

    The thesis deals with the effect of annealing in the temperature range 150-500 degrees celsius, and long-term ageing (1-150 days) at 150 degrees celsius, on the structure and mechanical properties of Kevlar-49 fibres. Wide-angle x-ray diffraction techniques were used to characterize quantitatively the structure in terms of crystallinity, crystallite size and orientation. The mechanical properties were characterized in terms of initial Young's modulus, tensile strength, and elongation at break. Thermogravimetric analysis was performed to determine the loss in weight after annealing. Differential Thermal Analysis (DTA) scan was performed to determine the 'peak melting point' of the untreated Kevlar-49 fibres. The surface topography, fracture behaviour and microfibrillar character of Kevlar-49 were studied in a scanning electron microscope. 52 refs., 30 figs., 6 tabs. (A.M.H.)

  7. Determination of moisture in fiber reinforced composites using pulsed NMR

    International Nuclear Information System (INIS)

    Matzkanin, G.A.

    1982-01-01

    Nuclear magnetic resonance (NMR) signals from hydrogen atoms in two organic matrix composite systems subjected to environmental conditioning at 51.6 C (125 F) and 95% relative humidity were examined. The composites were 8 ply, + or - 45 deg laminates fabricated from SP 250 resin/S2 glass fiber and Reliabond 9350 resin/Kevlar 49 fiber. Free induction decay NMR signals from the composite specimens consisted of a large amplitude, fast decaying component associated with hydrogen in rigid polymer molecules and a lower amplitude, slower decaying component associated with hydrogen in the mobile absorbed moisture molecules. The absorbed moisture NMR signals consists of distinct multiple components which were attributed to moisture in various states of molecular binding. Particularly complex free induction decay signals were observed from Kevlar composite as well as from Kevlar fiber. Good correlation was obtained between the NMR signal amplitude and the dry weight moisture percentage for both composite systems. Results of destructive tensile tests were examined

  8. Intricacies of Using Kevlar Cord and Thermal Knives in a Deployable Release System: Issues and Solutions

    Science.gov (United States)

    Stewart, Alphonso; Hair, Jason H.

    2002-01-01

    The utilization of Kevlar cord and thermal knives in a deployable release system produces a number of issues that must be addressed in the design of the system. This paper proposes design considerations that minimize the major issues, thermal knife failure, Kevlar cord relaxation, and the measurement of the cord tension. Design practices can minimize the potential for thermal knife laminate and element damage that result in failure of the knife. A process for in-situ inspection of the knife with resistance, rather than continuity, checks and 10x zoom optical imaging can detect damaged knives. Tests allow the characterization of the behavior of the particular Kevlar cord in use and the development of specific prestretching techniques and initial tension values needed to meet requirements. A new method can accurately measure the tension of the Kevlar cord using a guitar tuner, because more conventional methods do not apply to arimid cords such as Kevlar.

  9. Effect of layering sequence and chemical treatment on the mechanical properties of woven kenaf–aramid hybrid laminated composites

    International Nuclear Information System (INIS)

    Yahaya, R.; Sapuan, S.M.; Jawaid, M.; Leman, Z.; Zainudin, E.S.

    2015-01-01

    Highlights: • The mechanical properties of woven kenaf/Kevlar hybrid composites were analysed. • The layering sequences affect the mechanical properties of hybrid composites. • Treated kenaf improves the mechanical properties of hybrid composites. - Abstract: This work aims to evaluate the effect of layering sequence and chemical treatment on mechanical properties of woven kenaf–Kevlar composites. Woven kenaf–aramid hybrid laminated composites fabricated through hand lay-up techniques by arranging woven kenaf and Kevlar fabrics in different layering sequences and by using treated kenaf mat. To evaluate the effect of chemical treatment on hybrid composites, the woven kenaf mat was treated with 6% sodium hydroxide (NaOH) diluted solution and compared mechanical properties with untreated kenaf hybrid composites. Results shows that the tensile properties of hybrid composites improved in 3-layer composites compared to 4-layer composites. Hybrid composite with Kevlar as outer layers display a better mechanical properties as compared to other hybrid composites. Tensile and flexural properties of treated hybrid composites are better than non-treated hybrid composites. The fractured surface of hybrid composites was investigated by scanning electron microscopy. This study is a part of exploration of potential application of the hybrid composite in high velocity impact application

  10. In-Situ Nondestructive Evaluation of Kevlar(Registered Trademark)and Carbon Fiber Reinforced Composite Micromechanics for Improved Composite Overwrapped Pressure Vessel Health Monitoring

    Science.gov (United States)

    Waller, Jess; Saulsberry, Regor

    2012-01-01

    NASA has been faced with recertification and life extension issues for epoxy-impregnated Kevlar 49 (K/Ep) and carbon (C/Ep) composite overwrapped pressure vessels (COPVs) used in various systems on the Space Shuttle and International Space Station, respectively. Each COPV has varying criticality, damage and repair histories, time at pressure, and pressure cycles. COPVs are of particular concern due to the insidious and catastrophic burst-before-leak failure mode caused by stress rupture (SR) of the composite overwrap. SR life has been defined [1] as the minimum time during which the composite maintains structural integrity considering the combined effects of stress level(s), time at stress level(s), and associated environment. SR has none of the features of predictability associated with metal pressure vessels, such as crack geometry, growth rate and size, or other features that lend themselves to nondestructive evaluation (NDE). In essence, the variability or surprise factor associated with SR cannot be eliminated. C/Ep COPVs are also susceptible to impact damage that can lead to reduced burst pressure even when the amount of damage to the COPV is below the visual detection threshold [2], thus necessitating implementation of a mechanical damage control plan [1]. Last, COPVs can also fail prematurely due to material or design noncompliance. In each case (SR, impact or noncompliance), out-of-family behavior is expected leading to a higher probability of failure at a given stress, hence, greater uncertainty in performance. For these reasons, NASA has been actively engaged in research to develop NDE methods that can be used during post-manufacture qualification, in-service inspection, and in-situ structural health monitoring. Acoustic emission (AE) is one of the more promising NDE techniques for detecting and monitoring, in real-time, the strain energy release and corresponding stress-wave propagation produced by actively growing flaws and defects in composite

  11. Strain Measurement during Stress Rupture of Composite Over-Wrapped Pressure Vessel with Fiber Bragg Gratings Sensors

    Science.gov (United States)

    Banks, Curtis E.; Grant, Joseph; Russell, Sam; Arnett, Shawn

    2008-01-01

    Fiber optic Bragg gratings were used to measure strain fields during Stress Rupture (SSM) test of Kevlar Composite Over-Wrapped Pressure Vessels (COPV). The sensors were embedded under the over-wrapped attached to the liner released from the Kevlar and attached to the Kevlar released from the liner. Additional sensors (foil gages and fiber bragg gratings) were surface mounted on the COPY liner.

  12. The Protective Effect of Kevlar ® Socks Against Hockey Skate Blade Injuries: A Biomechanical Study

    Science.gov (United States)

    Nauth, Aaron; Aziz, Mina; Tsuji, Matthew; Whelan, Daniel B.; Theodoropoulos, John S.; Zdero, Rad

    2014-01-01

    Objectives: Several recent high profile injuries to elite players in the National Hockey League (NHL) secondary to skate blade lacerations have generated significant interest in these injuries and possible methods to protect against them. These injuries are typically due to direct contact of the skate blade of another player with posterior aspect of the calf resulting in a range of potential injuries to tendons or neurovascular structures. The Achilles tendon is most commonly involved. Kevlar® reinforced socks have recently become available for hockey players to wear and are cited as providing possible protection against such injuries. However, there has been no investigation of the possible protective effects of Kevlar® reinforced socks against skate blade injuries, and it is currently unknown what protective effects, if any, that these socks provide against these injuries. The proposed study sought to address this by conducting a biomechanical investigation of the protective effects of Kevlar® reinforced socks against Achilles tendon injuries in a simulated model of skate blade injury using human cadaver limbs. This novel investigation is the first to address the possible benefits to hockey players of wearing Kevlar® reinforced socks. Methods: Seven matched pairs of human cadaver lower limbs were fitted with a Kevlar ® reinforced sock comprised of 60% Kevlar®/20% Coolmax® polyester/18 % Nylon/12% Spandex (Bauer Elite Performance Skate Sock) on one limb and a standard synthetic sock comprised of 51% polyester/47% nylon/2% spandex (Bauer Premium Performance Skate Sock) on the contralateral limb as a control. Each limb was then mounted on a Materials Testing System (MTS) with the ankle dorsiflexed to 90° and the knee held in full extension using a custom designed jig. Specimens were then impacted with a hockey skate blade directed at the posterior calf, 12 cm above the heel, at an angle of 45° and a speed of 31m/s, to a penetration depth of 4.3 cm, to

  13. [Surface grafting modification and stabilization of Kevlar fiber].

    Science.gov (United States)

    Zheng, Yu-ying; Fu, Ming-lian; Wang, Can-yao; Wang, Liang-en

    2005-11-01

    Chemical disposal was used to bring the activity group onto the surface of Kevlar fiber for the purpose of surface grafting modification. The interfacial constitution of the grafting of toluene-2,4-diisocyanate (TDI) onto Kevlar fiber was determined by Fourier transform infrared spectroscopy. In the mean time, hexyl-lactam stabilization and poly-glycol (400, PEG) stabilization on the grafted product were also studied. The effects of different nTDI:nPEG ratios on the production's interfacial constitution was analysed. It is concluded that the stabilization took place on the surface. The intensity of the bands relented at about 3300 cm(-1) and was reinforced at about 1700-1720 cm(-1) when the ratio of nTDI:nPEG = 1:3, but when the ratio is 1:1 and 1:2, the bands at about 3 300 and 1700-1720 cm(-1) are almost the same.

  14. Effects of Crimped Fiber Paths on Mixed Mode Delamination Behaviors in Woven Fabric Composites

    Science.gov (United States)

    2016-09-01

    of several fabric weave styles and crimp gradients on the damage tolerance and energy absorption capacities in 20-ply Kevlar / epoxy composite...Styles and Crimp Gradients on Woven Kevlar Epoxy Composites,” Experimental Mechanics, vol. 56, no. 4, pp. 617–635, 2016. 12. ABAQUS, Ver. 6.10...mismatched element sizes between interface surfaces. Benzeggagh and Kenane3 conducted experimental tests and fractography on 6-mm-thick E-glass/ epoxy

  15. An experimental study of the effects of water repellant treatment on the acoustic properties of Kevlar

    Science.gov (United States)

    Smith, C. D.; Parrott, T. L.

    1978-01-01

    The treatment consisted of immersing samples of Kevlar in a solution of distilled water and Zepel. The samples were then drained, dried in a circulating over, and cured. Flow resistance tests showed approximately one percent decrease in flow resistance of the samples. Also there was a density increase of about three percent. It was found that the treatment caused a change in the texture of the samples. There were significant changes in the acoustic properties of the treated Kevlar over the frequency range 0.5 to 3.5 kHz. In general it was found that the propagation constant and characteristic impedance increased with increasing frequency. The real and imaginary components of the propagation constant for the treated Kevlar exhibited a decrease of 8 to 12 percent relative to that for the untreated Kevlar at the higher frequencies. The magnitude of the reactance component of the characteristic impedance decreased by about 40 percent at the higher frequencies.

  16. Fracture resistance of Kevlar-reinforced poly(methyl methacrylate) resin: a preliminary study.

    Science.gov (United States)

    Berrong, J M; Weed, R M; Young, J M

    1990-01-01

    The reinforcing effect of Kevlar fibers incorporated in processed poly(methyl methacrylate) resin samples was studied using 0% (controls), 0.5%, 1%, and 2% by weight of the added fibers. The samples were subjected to impact testing to determine fracture resistance, and sample groups were statistically compared using an ANOVA. Each reinforced sample had significantly greater fracture resistance (P less than 0.05) than the control, and no difference was found either within or between control groups. The use of reinforcing Kevlar fibers appears to enhance the fracture resistance of acrylic resin denture base materials.

  17. Transverse Compression Response of a Multi-Ply Kevlar Vest

    National Research Council Canada - National Science Library

    Raftenberg, Martin N; Scheidler, Michael J; Moy, Paul

    2004-01-01

    Each of the two 38 X 38-cm square panels, consisting of 28 plies of plain-woven 600-denier Kevlar KM2 and a Cordura case, was loaded in quasistatic, transverse compression by means of an Instron machine...

  18. Why does Kevlar decompose, while Nomex does not, when treated with aqueous chlorine solutions?

    Science.gov (United States)

    Akdag, Akin; Kocer, Hasan B; Worley, S D; Broughton, R M; Webb, T R; Bray, Travis H

    2007-05-24

    Kevlar and Nomex are high-performance polymers which have wide varieties of applications in daily life. Recently, they have been proposed to be biocidal materials when reacted with household bleach (sodium hypochlorite solution) because they contain amide moieties which can be chlorinated to generate biocidal N-halamine functional groups. Although Nomex can be chlorinated without any significant decomposition, Kevlar decomposes under the same chlorination conditions. In this study, two mimics for each of the polymers were synthesized to simulate the carboxylate and diaminophenylene components of the materials. It was found that the p-diaminophenylene component of the Kevlar mimic is oxidized to a quinone-type structure upon treatment with hypochlorous acid, which then decomposes. However, such a mechanism for the Nomex mimic is not possible. In this paper, based upon these observations, a plausible answer will be provided to the title question.

  19. Acoustic behavior of a fibrous bulk material. [Kevlar 29 sound absorber

    Science.gov (United States)

    Hersh, A. S.; Walker, B.

    1979-01-01

    A semiempirical model is presented describing the acoustic behavior of Kevlar 29, a bulk absorbing material. The model is based on an approximate solution to the one-dimensional equations representing conservation of fluctuating mass, momentum and energy. By treating the material as a momentum sink, theoretical expressions of the material complex propagation constants and characteristic impedance were derived in terms of a single constant. Evaluating the constant at a single frequency for a particular specimen, excellent agreement between prediction and measurement was achieved for a large range of sound frequencies and material porosities and thicknesses. Results show that Kevlar 29 absorbs sound efficiently even at low frequencies. This is explained in terms of a frequency dependent material phase speed.

  20. Quantitative radiographic analysis of fiber reinforced polymer composites.

    Science.gov (United States)

    Baidya, K P; Ramakrishna, S; Rahman, M; Ritchie, A

    2001-01-01

    X-ray radiographic examination of the bone fracture healing process is a widely used method in the treatment and management of patients. Medical devices made of metallic alloys reportedly produce considerable artifacts that make the interpretation of radiographs difficult. Fiber reinforced polymer composite materials have been proposed to replace metallic alloys in certain medical devices because of their radiolucency, light weight, and tailorable mechanical properties. The primary objective of this paper is to provide a comparable radiographic analysis of different fiber reinforced polymer composites that are considered suitable for biomedical applications. Composite materials investigated consist of glass, aramid (Kevlar-29), and carbon reinforcement fibers, and epoxy and polyether-ether-ketone (PEEK) matrices. The total mass attenuation coefficient of each material was measured using clinical X-rays (50 kev). The carbon fiber reinforced composites were found to be more radiolucent than the glass and kevlar fiber reinforced composites.

  1. Laser cutting of Kevlar laminates

    Energy Technology Data Exchange (ETDEWEB)

    VanCleave, R.A.

    1977-09-01

    An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

  2. Design prediction for long term stress rupture service of composite pressure vessels

    Science.gov (United States)

    Robinson, Ernest Y.

    1992-01-01

    Extensive stress rupture studies on glass composites and Kevlar composites were conducted by the Lawrence Radiation Laboratory beginning in the late 1960's and extending to about 8 years in some cases. Some of the data from these studies published over the years were incomplete or were tainted by spurious failures, such as grip slippage. Updated data sets were defined for both fiberglass and Kevlar composite stand test specimens. These updated data are analyzed in this report by a convenient form of the bivariate Weibull distribution, to establish a consistent set of design prediction charts that may be used as a conservative basis for predicting the stress rupture life of composite pressure vessels. The updated glass composite data exhibit an invariant Weibull modulus with lifetime. The data are analyzed in terms of homologous service load (referenced to the observed median strength). The equations relating life, homologous load, and probability are given, and corresponding design prediction charts are presented. A similar approach is taken for Kevlar composites, where the updated stand data do show a turndown tendency at long life accompanied by a corresponding change (increase) of the Weibull modulus. The turndown characteristic is not present in stress rupture test data of Kevlar pressure vessels. A modification of the stress rupture equations is presented to incorporate a latent, but limited, strength drop, and design prediction charts are presented that incorporate such behavior. The methods presented utilize Cartesian plots of the probability distributions (which are a more natural display for the design engineer), based on median normalized data that are independent of statistical parameters and are readily defined for any set of test data.

  3. Kevlar® as a Potential Accident Radiation Dosimeter for First Responders, Law Enforcement and Military Personnel.

    Science.gov (United States)

    Romanyukha, Alexander; Trompier, François; Benevides, Luis A

    2016-08-01

    Today the armed forces and law enforcement personnel wear body armor, helmets, and flak jackets composed substantially of Kevlar® fiber to prevent bodily injury or death resulting from physical, ballistic, stab, and slash attacks. Therefore, there is a high probability that during a radiation accident or its aftermath, the Kevlar®-composed body armor will be irradiated. Preliminary study with samples of Kevlar® foundation fabric obtained from body armor used by the U.S. Marine Corps has shown that all samples evaluated demonstrated an EPR signal, and this signal increased with radiation dose. Based on these results, the authors predict that, with individual calibration, exposure at dose above 1 Gy can be reliably detected in Kevlar® samples obtained from body armor. As a result of these measurements, a post-event reconstruction of exposure dose can be obtained by taking various samples throughout the armor body and helmet worn by the same irradiated individual. The doses can be used to create a whole-body dose map that would be of vital importance in a case of a partial body or heterogeneous exposure.

  4. Kevlar: Transitioning Helix for Research to Practice

    Science.gov (United States)

    2016-03-01

    x86 binaries, although it can be targeted to any platform that is targeted by IDA Pro. Currently, IDA Pro targets more than 40 processors and...effects its own transformations. Helix/Kevlar then automatically generates SPRI rules for any program variants by essentially performing a “ smart diff...execute permission on the pages of memory it uses, leaving only execute (but not write) permission on the code cache. Strata also watches for attempts

  5. Experimental determinations of the eigenmodes for composite bars made with carbon and Kevlar-carbon fibers

    Science.gov (United States)

    Miriţoiu, C. M.; Stănescu, M. M.; Burada, C. O.; Bolcu, D.; Roşca, V.

    2015-11-01

    For modal identification, the single-point excitation method has been widely used in modal tests and it consists in applying a force in a given point and recording the vibratory structure response in all interest points, including the excitation point. There will be presented the experimental recordings for the studied bars (with Kevlar-carbon or carbon fibers), the frequency response function in Cartesian and polar coordinates. By using the frequency response functions we determine the eigenparameters for each bar. We present the final panel of the eigenmodes (with the damping factors, eigenfrequencies and critical damping) for each considered bar. Using the eigenfrequency of the first determined eigenmode, the bars stiffness has been determined. The presented bars can be used in practical engineering for: car or bus body parts, planes body parts, bullet-proof vests, reinforcements for sandwich beams, and so on.

  6. Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

    Science.gov (United States)

    Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

    2017-11-01

    A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

  7. Analysis of Steel-With-Composite Material Substitution in Military Vehicle Hull Floors Subjected to Shallow-Buried Landmine-Detonation Loads

    Science.gov (United States)

    2014-01-01

    of either a Kevlars -fiber reinforced poly-vinyl- epoxy -matrix composite or AISI 4340 steel. The deformation and failure constitutive response of these...J.S., Yen, C.-F. and Cheeseman, B.A. (2013a), “Multi-length scale enriched continuum-level material model for Kevlars -fiber reinforced polymer-matrix

  8. Influence of Immersion Conditions on The Tensile Strength of Recycled Kevlar®/Polyester/Low-Melting-Point Polyester Nonwoven Geotextiles through Applying Statistical Analyses

    Directory of Open Access Journals (Sweden)

    Jing-Chzi Hsieh

    2016-05-01

    Full Text Available The recycled Kevlar®/polyester/low-melting-point polyester (recycled Kevlar®/PET/LPET nonwoven geotextiles are immersed in neutral, strong acid, and strong alkali solutions, respectively, at different temperatures for four months. Their tensile strength is then tested according to various immersion periods at various temperatures, in order to determine their durability to chemicals. For the purpose of analyzing the possible factors that influence mechanical properties of geotextiles under diverse environmental conditions, the experimental results and statistical analyses are incorporated in this study. Therefore, influences of the content of recycled Kevlar® fibers, implementation of thermal treatment, and immersion periods on the tensile strength of recycled Kevlar®/PET/LPET nonwoven geotextiles are examined, after which their influential levels are statistically determined by performing multiple regression analyses. According to the results, the tensile strength of nonwoven geotextiles can be enhanced by adding recycled Kevlar® fibers and thermal treatment.

  9. Kevlar based nanofibrous particles as robust, effective and recyclable absorbents for water purification.

    Science.gov (United States)

    Nie, Chuanxiong; Peng, Zihang; Yang, Ye; Cheng, Chong; Ma, Lang; Zhao, Changsheng

    2016-11-15

    Developing robust and recyclable absorbents for water purification is of great demand to control water pollution and to provide sustainable water resources. Herein, for the first time, we reported the fabrication of Kevlar nanofiber (KNF) based composite particles for water purification. Both the KNF and KNF-carbon nanotube composite particles can be produced in large-scale by automatic injection of casting solution into ethanol. The resulted nanofibrous particles showed high adsorption capacities towards various pollutants, including metal ions, phenylic compounds and various dyes. Meanwhile, the adsorption process towards dyes was found to fit well with the pseudo-second-order model, while the adsorption speed was controlled by intraparticle diffusion. Furthermore, the adsorption capacities of the nanofibrous particles could be easily recovered by washing with ethanol. In general, the KNF based particles integrate the advantages of easy production, robust and effective adsorption performances, as well as good recyclability, which can be used as robust absorbents to remove toxic molecules and forward the application of absorbents in water purification. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Virginia Tech's K-9 unit to receive Kevlar vest from alumni organization

    OpenAIRE

    Dickerson, Susan

    2004-01-01

    Hokie, the Virginia Tech Police Department's German shepherd, will be presented with a custom-fitted Virginia Tech Kevlar bulletproof vest to protect him from all the dangers he faces while performing his daily duties.

  11. Mechanical Tensile Testing of Titanium 15-3-3-3 and Kevlar 49 at Cryogenic Temperatures

    Science.gov (United States)

    James, Bryan L.; Martinez, Raul M.; Shirron, Peter; Tuttle, Jim; Galassi, Nicholas M.; Mcguinness, Daniel S.; Puckett, David; Francis, John J.; Flom, Yury

    2011-01-01

    Titanium 15-3-3-3 and Kevlar 49 are highly desired materials for structural components in cryogenic applications due to their low thennal conductivity at low temperatures. Previous tests have indicated that titanium 15-3-3-3 becomes increasingly brittle as the temperature decreases. Furthermore, little is known regarding the mechanical properties of Kevlar 49 at low temperatures, most specifically its Young's modulus. This testing investigates the mechanical properties of both materials at cryogenic temperatures through cryogenic mechanical tensile testing to failure. The elongation, ultimate tensile strength, yield strength, and break strength of both materials are provided and analyzed here.

  12. [The research on the surfacial modification of organic high-performance Kevlar fiber].

    Science.gov (United States)

    Zheng, Yu-ying; Fu, Ming-lian; Cai, Wei-long; Wang, Can-yao; Wang, Liang-en

    2004-04-01

    In the paper the authors tried to use chemical disposal to bring the activity mass onto the surface of Kevlar fiber with the purpose of surface graft modification. In the paper the authors used the FTIR spectra to discuss the graft of toluene-2, 4-diisocyanate onto Kevlar fiber. The authors studied and analysed the effect of hydrolytic time on the content of -O-H group of the production, and the effect of hydrolyzation and hexyl-lactam steadily disposing on the graft reaction. The result showed that the content of -O-H group increased after hydrolyzation, it's helpful for the graft reaction, and hexyl-lactam steadily disposing made the graf product more stable. Through the research the authors came to the conclusion that by bringing some activity masses onto the fiber surface the authors can improve the interface of fiber/resin effectively.

  13. Enhancement in ballistic performance of composite hard armor through carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Jason Gibson

    2013-12-01

    Full Text Available The use of carbon nanotubes in composite hard armor is discussed in this study. The processing techniques to make various armor composite panels consisting of Kevlar®29 woven fabric in an epoxy matrix and the subsequent V50 test results for both 44 caliber soft-point rounds and 30 caliber FSP (fragment simulated projectile threats are presented. A 6.5% improvement in the V50 test results was found for a combination of 1.65 wt% loading of carbon nanotubes and 1.65 wt% loading of milled fibers. The failure mechanism of carbon nanotubes during the ballistic event is discussed through scanning electron microscope images of the panels after the failure. Raman Spectroscopy was also utilized to evaluate the residual strain in the Kevlar®29 fibers post shoot. The Raman Spectroscopy shows a Raman shift of 25 cm−1 for the Kevlar®29 fiber utilized in the composite panel that had an enhancement in the V50 performance by using milled fiber and multi-walled carbon nanotubes. Evaluating both scenarios where an improvement was made and other panels without any improvement allows for understanding of how loading levels and synergistic effects between carbon nanotubes and milled fibers can further enhance ballistic performance.

  14. Clinical, biomechanical and morphological assessment of anterior cruciate ligament Kevlar®-based artificial prosthesis in rabbit model.

    Science.gov (United States)

    de la Garza-Castro, Santiago; González-Rivera, Carlos E; Vílchez-Cavazos, Félix; Morales-Avalos, Rodolfo; Barrera-Flores, Francisco J; Elizondo-Omaña, Rodrigo E; Soto-Dominguez, Adolfo; Acosta-Olivo, Carlos; Mendoza-Lemus, Oscar F

    2017-07-27

    The aim of this study was to evaluate the clinical, biomechanical and morphological characteristics of a Kevlar®-based prosthetic ligament as a synthetic graft of the anterior cruciate ligament (ACL) in an experimental animal model in rabbits. A total of 27 knees of rabbits randomly divided into 3 groups (control, ACL excision and ACL replacement with a Kevlar® prosthesis) were analyzed using clinical, biomechanical and morphological tests at 6, 12 and 18 weeks postprocedure. The mean displacement in mechanical testing was 0.73 ± 0.06 mm, 1.58 ± 0.19 mm and 0.94 ± 0.20 mm for the control, ACL excision and ACL replacement with synthetic prosthesis groups, respectively. The results showed an improvement in the stability of the knee with the use of the Kevlar® synthetic prosthesis in the biomechanical testing (p0.05), between the replacement group and the control group. The histological study revealed a good morphological adaptation of the synthetic material to the knee. This study proposes a new animal model for the placement and evaluation of Kevlar®-based synthetic ACL implants. The studied prosthesis showed promising behavior in the clinical and biomechanical tests and in the histological analysis. This study lays the foundation for further basic and clinical studies of artificial ACL prostheses using this material.

  15. Local Strain Measurement of Kevlar Strand with Fiber Optic Bragg Grating

    Science.gov (United States)

    Banks, Curtis E.; Grant, Joseph; Russell, Sam; Arnett, Shawn

    2008-01-01

    1987 DuPont manufactured 4560 denier Kevlar/Epoxy Strands were instrumented with nine and three sensors each. Stress tests were performed at 30,45,60,70 and 80% of ultimate strength with dwell times of 10,000 seconds. FBG showed uneven stress levels which is contrary to conventional observation.

  16. Fracto-emission from graphite/epoxy composites

    Science.gov (United States)

    Dickinson, J. T.

    1983-01-01

    Fracto-emission (FE) is the emission of particles and photons during and following crack propagation. Electrons (EE), positive ions (PIE), and excited and ground state neutrals (NE) were observed. Results of a number of experiments involving principally graphite/epoxy composites and Kevlar single fibers are presented. The physical processes responsible for EE and PIE are discussed as well as FE from fiber- and particulate-reinforced composites.

  17. Composite materials. From gammas to weight measurement

    International Nuclear Information System (INIS)

    Anon.

    1998-01-01

    A gamma photons backscattering gauge called 'Filbor 2' has been designed by the CEA/DAMRI (Saclay, France) and allows to measure the resin content of fiber wicks (boron, carbon, kevlar, glass..) devoted to the manufacturing of elements made of composite materials. (J.S.)

  18. High-performance fiber/epoxy composite pressure vessels

    Science.gov (United States)

    Chiao, T. T.; Hamstad, M. A.; Jessop, E. S.; Toland, R. H.

    1978-01-01

    Activities described include: (1) determining the applicability of an ultrahigh-strength graphite fiber to composite pressure vessels; (2) defining the fatigue performance of thin-titanium-lined, high-strength graphite/epoxy pressure vessel; (3) selecting epoxy resin systems suitable for filament winding; (4) studying the fatigue life potential of Kevlar 49/epoxy pressure vessels; and (5) developing polymer liners for composite pressure vessels. Kevlar 49/epoxy and graphite fiber/epoxy pressure vessels, 10.2 cm in diameter, some with aluminum liners and some with alternation layers of rubber and polymer were fabricated. To determine liner performance, vessels were subjected to gas permeation tests, fatigue cycling, and burst tests, measuring composite performance, fatigue life, and leak rates. Both the metal and the rubber/polymer liner performed well. Proportionately larger pressure vessels (20.3 and 38 cm in diameter) were made and subjected to the same tests. In these larger vessels, line leakage problems with both liners developed the causes of the leaks were identified and some solutions to such liner problems are recommended.

  19. Electron-beam-induced fracture of Kevlar single fibers

    International Nuclear Information System (INIS)

    Dickinson, J.T.; Jensen, L.C.; Klakken, M.L.

    1986-01-01

    We examine the unique situation involving the exposure of polymers to both electron bombardment and mechanical stress. Under certain conditions, crack formation, crack growth, and fracture can occur due to this combination of stimuli. These studies relate to the performance of a number of materials under hostile environments such as space, plasma, and propulsion systems. In this paper we present our initial measurements on the response of single Kevlar fibers loaded in tension to bombardment by 3-keV electrons. We present evidence that the resulting electron-beam-induced fracture is due to bond breaking

  20. The behavior of Kevlar fibers under environmental-stress conditions

    Science.gov (United States)

    Perry, Mark Charles

    There are a myriad of mechanisms by which polymers can degrade and fail. It is therefore important to understand the physical mechanics, chemistry, their interactions, and kinetics. This pursuit becomes more than just "academic" because these mechanisms might just change with service conditions (i.e. environment and loading). If one does not understand these processes from the molecular to macroscopic scale it would be exceedingly difficult to gain information from accelerated testing because the mechanisms just might change from one condition to another. The purpose of this study was to probe these processes on scales ranging from molecular to macroscopic in environmental stress conditions. This study reports the results of environmental-stress degradation of Kevlar 49 fibers. The environmental agent of focus was the ubiquitous air pollutant complex NOsb{x}. Other materials and environments were investigated to a lesser extent for purposes of comparison. Mechanical property (i.e., short-term strength, modulus, and creep lifetime) degradation was examined using single fiber, yarn, and epoxy coated yarn (composite) specimens under environmental-stress conditions. Optical and scanning electron microscopes were employed to examine and compare the appearance of fracture features resulting from the various testing conditions. Atomic force microscopy augmented these studies with detailed topographical mappings and measures of the fracture surface frictional and modulus properties. Molecular processes (i.e., chain scission and other mechanical-chemical reactions) were probed by measures of changes in viscosity average molecular weight and the infrared spectra. It was demonstrated that environmental-stress degradation effects do occur in the Kevlar-NOsb{x} gas system. Strength decay in environmentally exposed unloaded fibers was demonstrated and a synergistic response in creep reduced fiber lifetimes by three orders of magnitude at moderate loadings. That is to say, the

  1. Analysis methods for Kevlar shield response to rotor fragments

    Science.gov (United States)

    Gerstle, J. H.

    1977-01-01

    Several empirical and analytical approaches to rotor burst shield sizing are compared and principal differences in metal and fabric dynamic behavior are discussed. The application of transient structural response computer programs to predict Kevlar containment limits is described. For preliminary shield sizing, present analytical methods are useful if insufficient test data for empirical modeling are available. To provide other information useful for engineering design, analytical methods require further developments in material characterization, failure criteria, loads definition, and post-impact fragment trajectory prediction.

  2. [Imaging of alloplastic ligament implant. An in vivo and in vitro study exemplified by Kevlar].

    Science.gov (United States)

    Wening, J V; Katzer, A; Nicolas, V; Hahn, M; Jungbluth, K H; Kratzer A [corrected to Katzer, A

    1994-04-01

    Neither native X-ray nor CT or NMR allow to evaluate intraarticular implantation results of Kevlar -49 directly. In animal trials, the course of an artificial ligament may only be presumed from connective tissue ingrowth. Although soft tissue structure appears much better in NMR than in CT, direct proof of ligament continuity is still impossible. As soon as the connective tissue becomes continuous, it appears clearly and allows indirect evaluation of the prosthesis, as integrity can be judged by its shape like in natural cruciate ligament. Anatomic preparations show that connective tissue fills up the small space between the two cords of a Kevlar -49 two bundle prosthesis eight weeks after implantation, so that imaging systems show only one intraarticular bundle.

  3. Simulation used to qualify nuclear waste glass for disposal

    International Nuclear Information System (INIS)

    Reimus, T.W.; Kuhn, W.L.

    1987-07-01

    A hypothetical vitrification system was simulated errors associated with controlling and predicting the composition of the nuclear waste glass produced in the system. The composition of the glass must fall within certain limits to qualify for permanent geologic disposal. The estimated error in predicting the concentrations of various constituents in the glass was 2% to 8%, depending on the strategy for sampling and analyzing the feed and on the assumed magnitudes of the process uncertainties. The estimated error in controlling the glass composition was 2% to 9%, depending on the strategy for sampling and analyzing the waste and on the assumed magnitudes of the uncertainties. This work demonstrates that simulation techniques can be used to assist in qualifying nuclear waste glass for disposal. 3 refs., 2 figs., 4 tabs

  4. Analysis of Particulate and Chemical Residue Resulting from Exposure to Burning and Abrading Composite Materials

    Science.gov (United States)

    2013-05-31

    National Aeronautics and Space Administration (NASA) initiated a study of reinforcing fiber release from graphite- epoxy composite, graphite- Kevlar ...amplifiers from cut virgin fiber and from fiber produced from burning graphite- epoxy composite were in close agreement.[2] Composite aircraft accidents...containing carbon/ epoxy composite crashed in Denmark in 1991. The recovery team suffered eye and skin irritation and respiratory difficulties.[3

  5. Characterization of Kevlar 49 fibers by electron paramagnetic resonance. Final report, 20 May 1981-20 June 1982

    International Nuclear Information System (INIS)

    Brown, I.M.; Sandreczki, T.C.

    1982-01-01

    EPR was used to investigate the free radicals created in Kevlar 49 fibers by stress-induced and photo-induced macromolecular chain scissions. Mn +2 ions were identified from the EPR spectrum of frozen solutions of concentrated sulfuric acid containing Kevlar 49. Other ions present are Cu +2 , and possibly Fe +3 , Cr +3 , and Ti +3 . EPR lineshape anisotropy indicates that some of the metal ions and first coordinate spheres are oriented. The concentration of stress-induced radicals (2 x 10 10 per filament) suggest that chain scission occurs in more weak planes than are estimated to exist in the fracture surfaces of the fiber core. These radicals are unstable in air and have some aromatic character. Several different types of radicals were obtained following uv irradiations of the Kevlar 49 fibers in vacuum (photodegradative radicals) and in air (photo-oxidative radicals). The photodegradative radicals are identified with primary radicals involved in the photo-Fries rearrangement reaction, secondary radicals formed as a result of a hydrogen atom abstraction by the primary radical, and/or ketyl radicals produced as a result of uv irradiation of the photo-Fries rearrangement product. The photo-oxidative radicals are identified with the uv irradiation products of a peroxide intermediate. Lineshape anisotropy indicates that both radical types are oriented. 31 figures

  6. Ballistic Performance of Mallow and Jute Natural Fabrics Reinforced Epoxy Composites in Multilayered Armor

    OpenAIRE

    Nascimento, Lucio Fabio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Marçal, Rubens Lincoln Santana Blazutti; Lima Júnior, Édio Pereira; Margem, Jean Igor

    2017-01-01

    Natural fiber reinforced polymer composites have recently been investigated as a component of multilayered armor system (MAS). These composites were found to present advantages when replacing conventional high strength synthetic aramid fabric laminate composite (KevlarTM, with same thickness, as MAS second layer. Continuous and loose natural fibers were up to now mostly used to reinforce these ballistic composites. Only two natural fabrics reinforced polymer composite were so far used with sa...

  7. Practical Considerations of Design, Fabrication and Tests for Composite Materials,

    Science.gov (United States)

    1982-09-01

    Harris 2 School of Materials Science University of Bath Claverton Down Bath AB2 7AY UK 1. THE IDEA OF A COMPOSITE The concept is a familiar one even to...A.R. Bunsell " Comportement en torsion des fibres de Kevlar-29 " Colloque nt CNRS No. 319 Comportement plastique des solides anisotropes. 16-19 June...d’hhlicoptares en composites : conception , rdalisation et comportement en operation ". Advances in Composite Materials Vol II Ed. A.R. Bunsell, C. Bathias

  8. Ballistic Impact Response of Kevlar 49 and Zylon under Conditions Representing Jet Engine Fan Containment

    Science.gov (United States)

    Pereira, J. Michael; Revilock, Duane M.

    2007-01-01

    A ballistic impact test program was conducted to provide validation data for the development of numerical models of blade out events in fabric containment systems. The impact response of two different fiber materials - Kevlar 49 (E.I. DuPont Nemours and Company) and Zylon AS (Toyobo Co., Ltd.) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation and velocity of the projectile were varied and recorded. In most cases the tests were designed such that the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models for predicting the response of fabrics under conditions simulating those of a jet engine blade release situation. In addition some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different materials.

  9. A Kinematic, Kevlar(registered) Suspension System for an ADR

    Science.gov (United States)

    Voellmer, George M.; Jackson, Michael L.; Shirron, Peter J.; Tuttle, James G.

    2003-01-01

    The High Resolution Airborne Wideband Camera (HAWC) and the Submillimeter And Far Infrared Experiment (SAFIRE) will use identical Adiabatic Demagnetization Refrigerators (ADR) to cool their bolometer detectors to 200mK and 100mK, respectively. In order to minimize thermal loads on the salt pill, a Kevlar@ suspension system is used to hold it in place. An innovative, kinematic suspension system is presented. The suspension system is unique in that it consists or two parts that can be assembled and tensioned offline, and later bolted onto the salt pill. The resulting assembly constrains each degree of freedom only once, yielding a kinematic, tensile structure.

  10. Transverse thermal expansion of carbon fiber/epoxy matrix composites

    Science.gov (United States)

    Helmer, J. F.; Diefendorf, R. J.

    1983-01-01

    Thermal expansion coefficients and moduli of elasticity have been determined experimentally for a series of epoxy-matrix composites reinforced with carbon and Kevlar fibers. It is found that in the transverse direction the difference between the properties of the fiber and the matrix is not as pronounced as in the longitudinal direction, where the composite properties are fiber-dominated. Therefore, the pattern of fiber packing tends to affect transverse composite properties. The transverse properties of the composites tested are examined from the standpoint of the concept of homogeneity defined as the variation of packing (or lack thereof) throughout a sample.

  11. AZ-2000-IECW and StaMet Black Kapton Options for Solar Probe Plus MAG Sensor MLI Kevlar/Polyimide Shells

    Science.gov (United States)

    Choi, Michael K.

    2017-01-01

    AZ-2000-IECW white paint and StaMet black Kapton have been evaluated for the Kevlar/polyimide shells that enclose the Solar Probe Plus Magnetometer (MAG) sensors and multilayer insulation. Flight qualification testing on AZ-2000-IECW painted Kevlar/polyimide laminate was completed at Goddard Space Flight Center. This paint potentially meets all the requirements. However, it has no flight heritage. StaMet is hotter in the sun, and is specular. The results of the MAG thermal balance test show StaMet meets the thermal requirement and heater power budget. The mission prefers to fly StaMet after evaluating the risks of AZ-2000-IECW flaking and glint from StaMet to the Star Trackers.

  12. Hydramite II screening tests of potential bremsstrahlung converter debris shield materials

    International Nuclear Information System (INIS)

    Reedy, E.D. Jr.; Hedemann, M.A.; Stark, M.A.

    1986-03-01

    Results of a brief test series aimed at screening a number of potential bremsstrahlung converter debris shield materials are reported. These tests were run on Sandia National Laboratories' Hydramite II accelerator using a diode configuration which produces a pinched electron beam. The materials tested include: (1) laminated Kevlar 49/polyester and E-glass/polyester composites, (2) a low density laminated Kevlar 49 composite, and (3) two types of through-the-thickness reinforced Kevlar 49 composites. As expected, tests using laminated Kevlar 49/polyester shields showed that shield permanent set (i.e., permanent deflection) increased with increasing tantalum conversion foil thickness and decreased with increasing shield thickness. The through-the-thickness reinforced composites developed localized, but severe, back surface damage. The laminated composites displayed little back surface damage, although extensive internal matrix cracking and ply delaminations were generated. Roughly the same degree of permanent set was produced in shields made from the low density Kevlar 49 composite and the Kevlar 49/polyester. The E-glass reinforced shields exhibited relatively low levels of permanent set

  13. Metallization of Kevlar fibers with gold.

    Science.gov (United States)

    Little, Brian K; Li, Yunfeng; Cammarata, V; Broughton, R; Mills, G

    2011-06-01

    Electrochemical gold plating processes were examined for the metallization of Kevlar yarn. Conventional Sn(2+)/Pd(2+) surface activation coupled with electroless Ni deposition rendered the fibers conductive enough to serve as cathodes for electrochemical plating. The resulting coatings were quantified gravimetrically and characterized via adhesion tests together with XRD, SEM, TEM; the coatings effect on fiber strength was also probed. XRD data showed that metallic Pd formed during surface activation whereas amorphous phases and trace amounts of pure Ni metal were plated via the electroless process. Electrodeposition in a thiosulfate bath was the most efficient Au coating process as compared with the analogous electroless procedure, and with electroplating using a commercial cyanide method. Strongly adhering coatings resulted upon metallization with three consecutive electrodepositions, which produced conductive fibers able to sustain power outputs in the range of 1 W. On the other hand, metallization affected the tensile strength of the fiber and defects present in the metal deposits make questionable the effectiveness of the coatings as protective barriers. © 2011 American Chemical Society

  14. Study on mechanical properties and damage behaviors of Kevlar fiber reinforced epoxy composites by digital image correlation technique under optical microscope

    Science.gov (United States)

    Gao, Xiang; Shao, Wenquan; Ji, Hongwei

    2010-10-01

    Kevlar fiber-reinforced epoxy (KFRE) composites are widely used in the fields of aerospace, weapon, shipping, and civil industry, due to their outstanding capabilities. In this paper, mechanical properties and damage behaviors of KFRE laminate (02/902) were tested and studied under tension condition. To precisely measure the tensile mechanical properties of the material and investigate its micro-scale damage evolution, a micro-image measuring system with in-situ tensile device was designed. The measuring system, by which the in-situ tensile test can be carried out and surface morphology evolution of the tensile specimen can be visually monitored and recorded during the process of loading, includes an ultra-long working distance zoom microscope and a in-situ tensile loading device. In this study, a digital image correlation method (DICM) was used to calculate the deformation of the tensile specimen under different load levels according to the temporal series images captured by an optical microscope and CCD camera. Then, the elastic modulus and Poisson's ratio of the KFRE was obtained accordingly. The damage progresses of the KFRE laminates were analyzed. Experimental results indicated that: (1) the KFRE laminate (02/902) is almost elastic, its failure mode is brittle tensile fracture.(2) Mechanical properties parameters of the material are as follows: elastic modulus is 14- 16GPa, and tensile ultimate stress is 450-480 Mpa respectively. (3) The damage evolution of the material is that cracks appear in epoxy matrix firstly, then, with the increasing of the tensile loading, matrix cracks add up and extend along a 45° angle direction with tensile load. Furthermore, decohesion between matrix and fibers as well as delamination occurs. Eventually, fibers break and the material is damaged.

  15. Durability of aircraft composite materials

    Science.gov (United States)

    Dextern, H. B.

    1982-01-01

    Confidence in the long term durability of advanced composites is developed through a series of flight service programs. Service experience is obtained by installing secondary and primary composite components on commercial and military transport aircraft and helicopters. Included are spoilers, rudders, elevators, ailerons, fairings and wing boxes on transport aircraft and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on helicopters. Materials included in the evaluation are boron/epoxy, Kevlar/epoxy, graphite/epoxy and boron/aluminum. Inspection, maintenance, and repair results for the components in service are reported. The effects of long term exposure to laboratory, flight, and outdoor environmental conditions are reported for various composite materials. Included are effects of moisture absorption, ultraviolet radiation, and aircraft fuels and fluids.

  16. Numerical Material Model for Composite Laminates in High-Velocity Impact Simulation

    Directory of Open Access Journals (Sweden)

    Tao Liu

    Full Text Available Abstract A numerical material model for composite laminate, was developed and integrated into the nonlinear dynamic explicit finite element programs as a material user subroutine. This model coupling nonlinear state of equation (EOS, was a macro-mechanics model, which was used to simulate the major mechanical behaviors of composite laminate under high-velocity impact conditions. The basic theoretical framework of the developed material model was introduced. An inverse flyer plate simulation was conducted, which demonstrated the advantage of the developed model in characterizing the nonlinear shock response. The developed model and its implementation were validated through a classic ballistic impact issue, i.e. projectile impacting on Kevlar29/Phenolic laminate. The failure modes and ballistic limit velocity were analyzed, and a good agreement was achieved when comparing with the analytical and experimental results. The computational capacity of this model, for Kevlar/Epoxy laminates with different architectures, i.e. plain-woven and cross-plied laminates, was further evaluated and the residual velocity curves and damage cone were accurately predicted.

  17. Torsional actuation with extension-torsion composite coupling and a magnetostrictive actuator

    Science.gov (United States)

    Bothwell, Christopher M.; Chandra, Ramesh; Chopra, Inderjit

    1995-04-01

    An analytical-experimental study of using magnetostrictive actuators in conjunction with an extension-torsion coupled composite tube to actuate a rotor blade trailing-edge flap to actively control helicopter vibration is presented. Thin walled beam analysis based on Vlasov theory was used to predict the induced twist and extension in a composite tube with magnetostrictive actuation. The study achieved good correlation between theory and experiment. The Kevlar-epoxy systems showed good correlation between measured and predicted twist values.

  18. Fracto-emission from single fibres of Kevlar

    Science.gov (United States)

    Dickinson, J. T.; Jahan-Latibari, A.; Jensen, L. C.

    1985-01-01

    Fracto-emission (FE) is the emission of particles (e.g. electrons, ions and photons) during and following fracture. In this paper, we present data on electron emission (EE) and positive ion emission (PIE) from the tensile fracture of Kevlar single fibers. The fibers were initially fractured in pure tension, where a stranded form of fracture was observed, often with multiple peaks spread over several hundred microseconds. The loading condition was then changed by stretching and breaking the fibers over a dull metal edge. With this change in the loading, different forms of fracture were observed, each with distinctive forms of emission curves. When fracture was accompanied by extensive fibril formation, total emission was high and both EE and PIE decay times were long relative to fractures in which little fibril formation occurred. The results of this study suggest that FE has some applicability as a tool for the detection of fracture mechanisms of single fibers.

  19. Free Vibration Response Comparison of Composite Beams with Fluid Structure Interaction

    Science.gov (United States)

    2012-09-01

    Derakane 510A-40 Epoxy Vinyl Ester Resin. After [23] .............................................................................................20...matrix material. The reinforcing fibers usually have high tensile and flexural strengths and moduli such as found in Kevlar , glass, and carbon...composites while matrix materials include epoxies , aluminum, and titanium. The layers of fibers can be oriented in varying ways and combined with different

  20. 17 CFR 240.3b-8 - Definitions of “Qualified OTC Market Maker, Qualified Third Market Maker” and “Qualified Block...

    Science.gov (United States)

    2010-04-01

    ... Market Maker, Qualified Third Market Makerâ and âQualified Block Positionerâ. 240.3b-8 Section 240.3b-8... “Qualified Block Positioner”. For the purposes of Regulation U under the Act (12 CFR part 221): (a) The term... inventory turnover in such security. (c) The term Qualified Block Positioner means a dealer who (1) is a...

  1. Additional results on space environmental effects on polymer matrix composites: Experiment A0180

    International Nuclear Information System (INIS)

    Tennyson, R.C.

    1992-01-01

    Additional experimental results on the atomic oxygen erosion of boron, Kevlar, and graphite fiber reinforced epoxy matrix composites are presented. Damage of composite laminates due to micrometeoroid/debris impacts is also examined with particular emphasis on the relationship between damage area and actual hole size due to particle penetration. Special attention is given to one micrometeoroid impact on an aluminum base plate which resulted in ejecta visible on an adjoining vertical flange structure

  2. A novel Ag catalyzation process using swelling impregnation method for electroless Ni deposition on Kevlar® fiber

    Science.gov (United States)

    Pang, Hongwei; Bai, Ruicheng; Shao, Qinsi; Gao, Yufang; Li, Aijun; Tang, Zhiyong

    2015-12-01

    A novel Ag catalyzation process using swelling impregnation pretreatment method was developed for electroless nickel (EN) deposition on Kevlar fiber. Firstly, the fiber was immersed into an aqueous dimethylsulfoxide (DMSO) solution of silver nitrate to impart silver nitrate into the inner part of the fiber near the surface. Subsequently silver nitrate was reduced to metal silver nanoparticles on the fiber surface by treatment with aqueous solution of sodium borohydride. After electroless plating, a dense and homogeneous nickel coating was obtained on the fiber surface. The silver nanoparticles formed at the fiber surface functioned as a catalyst for electroless deposition as well as an anchor for the plated layer. The study also revealed that the incorporation of surfactant sodium dodecyl sulfate (SDS) in electroless nickel plating bath can enhance the adhesion strength of EN layer with the fiber surface and minimize the surface roughness of the EN coating. The Ni plated Kevlar fiber possessed excellent corrosion resistance and high tensile strength.

  3. Radiometric determinations of linear mass, resin levels and density of composite materials

    International Nuclear Information System (INIS)

    Boutaine, J.L.; Pintena, J.; Tanguy, J.C.

    1978-01-01

    A description is given of the principle, characteristics and performances of a gamma back-scattering gauge developed in cooperation between the CEA and SNPE. This instrument allows for on-line inspection of the linear mass and resin level of strips of composite materials whilst being produced. The industrial application involved boron, carbon and 'Kevlar' fibres. The performance of beta and gamma transmission gauges are also given for inspecting the density of panels and dense composite materials [fr

  4. The Effect of Strike Face Geometry on the Dynamic Delamination of Composite Back Plates

    Science.gov (United States)

    2015-01-01

    behind the ceramic (Zuogang et al. 2010). In many cases, Kevlar , S-2 glass, ultra-high-molecular-weight polyethylene, or a similar high- performance...thin, translucent S-2 glass/SC-15 epoxy backing plate. A 0.30-cal. fragment-simulating projectile (FSP) was used to strike the front of the target... epoxy was chosen as the composite backing. Quasi-static material and high strain- rate properties for this composite are well characterized and have been

  5. Eddy Current COPV Overwrap and Liner Thickness Measurement System and Data Analysis for 40-Inch Kevlar COPVs SN002 and SN027

    Science.gov (United States)

    Wincheski, Russell A.

    2008-01-01

    As part of the health assessment of flight spare 40in diameter Kevlar composite overwrapped pressure vessels (COPVs) SN002 and SN027 an eddy current characterization of the composite and liner thickness change during pressurization was requested under WSTF-TP-1085-07.A, "Space Shuttle Orbiter Main Propulsion System P/N MC282-0082-0101 S/N 002 and Orbital Maneuvering System P/N MC282-0082-001 S/N 027 COPV Health Assessment." The through the thickness strains have been determined to be an important parameter in the analysis of the reliability and likelihood of stress rupture failure. Eddy current techniques provide a means to measure these thicknesses changes based upon the change in impedance of an eddy current sensor mounted on the exterior of the vessel. Careful probe and technique design have resulted in the capability to independently measure the liner and overwrap thickness changes to better than +/- 0.0005 in. at each sensor location. Descriptions of the inspection system and test results are discussed.

  6. Enhancement of mechanical and electrical properties of continuous-fiber-reinforced epoxy composites with stacked graphene.

    Science.gov (United States)

    Naveh, Naum; Shepelev, Olga; Kenig, Samuel

    2017-01-01

    Impregnation of expandable graphite (EG) after thermal treatment with an epoxy resin containing surface-active agents (SAAs) enhanced the intercalation of epoxy monomer between EG layers and led to further exfoliation of the graphite, resulting in stacks of few graphene layers, so-called "stacked" graphene (SG). This process enabled electrical conductivity of cured epoxy/SG composites at lower percolation thresholds, and improved thermo-mechanical properties were measured with either Kevlar, carbon or glass-fiber-reinforced composites. Several compositions with SAA-modified SG led to higher dynamic moduli especially at high temperatures, reflecting the better wetting ability of the modified nanoparticles. The hydrophilic/hydrophobic nature of the SAA dictates the surface energy balance. More hydrophilic SAAs promoted localization of the SG at the Kevlar/epoxy interface, and morphology seems to be driven by thermodynamics, rather than the kinetic effect of viscosity. This effect was less obvious with carbon or glass fibers, due to the lower surface energy of the carbon fibers or some incompatibility with the glass-fiber sizing. Proper choice of the surfactant and fine-tuning of the crosslink density at the interphase may provide further enhancements in thermo-mechanical behavior.

  7. Enhancement of mechanical and electrical properties of continuous-fiber-reinforced epoxy composites with stacked graphene

    Directory of Open Access Journals (Sweden)

    Naum Naveh

    2017-09-01

    Full Text Available Impregnation of expandable graphite (EG after thermal treatment with an epoxy resin containing surface-active agents (SAAs enhanced the intercalation of epoxy monomer between EG layers and led to further exfoliation of the graphite, resulting in stacks of few graphene layers, so-called “stacked” graphene (SG. This process enabled electrical conductivity of cured epoxy/SG composites at lower percolation thresholds, and improved thermo-mechanical properties were measured with either Kevlar, carbon or glass-fiber-reinforced composites. Several compositions with SAA-modified SG led to higher dynamic moduli especially at high temperatures, reflecting the better wetting ability of the modified nanoparticles. The hydrophilic/hydrophobic nature of the SAA dictates the surface energy balance. More hydrophilic SAAs promoted localization of the SG at the Kevlar/epoxy interface, and morphology seems to be driven by thermodynamics, rather than the kinetic effect of viscosity. This effect was less obvious with carbon or glass fibers, due to the lower surface energy of the carbon fibers or some incompatibility with the glass-fiber sizing. Proper choice of the surfactant and fine-tuning of the crosslink density at the interphase may provide further enhancements in thermo-mechanical behavior.

  8. Durability of commercial aircraft and helicopter composite structures

    International Nuclear Information System (INIS)

    Dexter, H.B.

    1982-01-01

    The development of advanced composite technology during the past decade is discussed. Both secondary and primary components fabricated with boron, graphite, and Kevlar composites are evaluated. Included are spoilers, rudders, and fairings on commercial transports, boron/epoxy reinforced wing structure on C-130 military transports, and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on commercial helicopters. The development of composite structures resulted in advances in design and manufacturing technology for secondary and primary composite structures for commercial transports. Design concepts and inspection and maintenance results for the components in service are reported. The flight, outdoor ground, and controlled laboratory environmental effects on composites were also determined. Effects of moisture absorption, ultraviolet radiation, aircraft fuels and fluids, and sustained tensile stress are included. Critical parameters affecting the long term durability of composite materials are identified

  9. Durability of commercial aircraft and helicopter composite structures

    Science.gov (United States)

    Dexter, H. B.

    1982-01-01

    The development of advanced composite technology during the past decade is discussed. Both secondary and primary components fabricated with boron, graphite, and Kevlar composites are evaluated. Included are spoilers, rudders, and fairings on commercial transports, boron/epoxy reinforced wing structure on C-130 military transports, and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on commercial helicopters. The development of composite structures resulted in advances in design and manufacturing technology for secondary and primary composite structures for commercial transports. Design concepts and inspection and maintenance results for the components in service are reported. The flight, outdoor ground, and controlled laboratory environmental effects on composites were also determined. Effects of moisture absorption, ultraviolet radiation, aircraft fuels and fluids, and sustained tensile stress are included. Critical parameters affecting the long term durability of composite materials are identified.

  10. Design of Automobile Driveshaft using Carbon/Epoxy and Kevlar/Epoxy Composites

    OpenAIRE

    R. Srinivasa Moorthy

    2013-01-01

    Use of advanced composites has resulted in remarkable achievements in many fields including aviation, marine and automobile engineering, medicine, prosthetics and sports, in terms of improved fatigue and corrosion resistances, high specific strength and specific modulus and reduction in energy requirements owing to reduction in weight. The aim of this work is to replace the conventional steel driveshaft of automobiles with an appropriate composite driveshaft. The conventional driveshafts ar...

  11. Tests of shielding effectiveness of Kevlar and Nextel onboard the International Space Station and the Foton-M3 capsule.

    Science.gov (United States)

    Pugliese, M; Bengin, V; Casolino, M; Roca, V; Zanini, A; Durante, M

    2010-08-01

    Radiation assessment and protection in space is the first step in planning future missions to the Moon and Mars, where mission and number of space travelers will increase and the protection of the geomagnetic shielding against the cosmic radiation will be absent. In this framework, the shielding effectiveness of two flexible materials, Kevlar and Nextel, were tested, which are largely used in the construction of spacecrafts. Accelerator-based tests clearly demonstrated that Kevlar is an excellent shield for heavy ions, close to polyethylene, whereas Nextel shows poor shielding characteristics. Measurements on flight performed onboard of the International Space Station and of the Foton-M3 capsule have been carried out with special attention to the neutron component; shielded and unshielded detectors (thermoluminescence dosemeters, bubble detectors) were exposed to a real radiation environment to test the shielding properties of the materials under study. The results indicate no significant effects of shielding, suggesting that thin shields in low-Earth Orbit have little effect on absorbed dose.

  12. Stress transfer in microdroplet tensile test: PVC-coated and uncoated Kevlar-29 single fiber

    Science.gov (United States)

    Zhenkun, Lei; Quan, Wang; Yilan, Kang; Wei, Qiu; Xuemin, Pan

    2010-11-01

    The single fiber/microdroplet tensile test is applied for evaluating the interfacial mechanics between a fiber and a resin substrate. It is used to investigate the influence of a polymer coating on a Kevlar-29 fiber surface, specifically the stress transfer between the fiber and epoxy resin in a microdroplet. Unlike usual tests, this new test ensures a symmetrical axial stress on the embedded fiber and reduces the stress singularity that appears at the embedded fiber entry. Using a homemade loading device, symmetrical tensile tests are performed on a Kevlar-29 fiber with or without polyvinylchloride (PVC) coating, the surface of which is in contact with two epoxy resin microdroplets during curing. Raman spectra on the embedded fiber are recorded by micro-Raman Spectroscopy under different strain levels. Then they are transformed to the distributions of fiber axis stress based on the relationship between stress and Raman shift. The Raman results reveal that the fiber axial stresses increase with the applied loads, and the antisymmetric interfacial shear stresses, obtained by a straightforward balance of shear-to-axial forces argument, lead to the appearance of shear stress concentrations at a distance to the embedded fiber entry. The load is transferred from the outer fiber to the embedded fiber in the epoxy microdroplet. As is observed by scanning electronic microscopy (SEM), the existence of a flexible polymer coating on the fiber surface reduces the stress transfer efficiency.

  13. Experimental and Analytical Evaluation of a Composite Honeycomb Deployable Energy Absorber

    Science.gov (United States)

    Jackson, Karen E.; Kellas, Sotiris; Horta, Lucas G.; Annett, Martin S.; Polanco, Michael A.; Littell, Justin D.; Fasanella, Edwin L.

    2011-01-01

    In 2006, the NASA Subsonic Rotary Wing Aeronautics Program sponsored the experimental and analytical evaluation of an externally deployable composite honeycomb structure that is designed to attenuate impact energy during helicopter crashes. The concept, which is designated the Deployable Energy Absorber (DEA), utilizes an expandable Kevlar honeycomb structure to dissipate kinetic energy through crushing. The DEA incorporates a unique flexible hinge design that allows the honeycomb to be packaged and stowed flat until needed for deployment. A variety of deployment options such as linear, radial, and/or hybrid methods can be used. Experimental evaluation of the DEA utilized a building block approach that included material characterization testing of its constituent, Kevlar -129 fabric/epoxy, and flexural testing of single hexagonal cells. In addition, the energy attenuation capabilities of the DEA were demonstrated through multi-cell component dynamic crush tests, and vertical drop tests of a composite fuselage section, retrofitted with DEA blocks, onto concrete, water, and soft soil. During each stage of the DEA evaluation process, finite element models of the test articles were developed and simulations were performed using the explicit, nonlinear transient dynamic finite element code, LS-DYNA. This report documents the results of the experimental evaluation that was conducted to assess the energy absorption capabilities of the DEA.

  14. Drop Weight Impact Studies of Woven Fibers Reinforced Modified Polyester Composites

    Directory of Open Access Journals (Sweden)

    Muhammed Tijani ISA

    2014-02-01

    Full Text Available Low velocity impact tests were conducted on modified unsaturated polyester reinforced with four different woven fabrics using hand-layup method to investigate the effect of fiber type and fiber combinations. The time-load curves were analysed and scanning electron microscopy was used to observe the surface of the impacted composite laminates. The results indicated that all the composites had ductility index (DI of above two for the test conducted at impact energy of 27J with the monolithic composite of Kevlar having the highest DI. The damage modes observed were mainly matrix cracks and fiber breakages. Hybridization of the fibers in the matrix was observed to minimize these damages.

  15. Stress Rupture Life Reliability Measures for Composite Overwrapped Pressure Vessels

    Science.gov (United States)

    Murthy, Pappu L. N.; Thesken, John C.; Phoenix, S. Leigh; Grimes-Ledesma, Lorie

    2007-01-01

    Composite Overwrapped Pressure Vessels (COPVs) are often used for storing pressurant gases onboard spacecraft. Kevlar (DuPont), glass, carbon and other more recent fibers have all been used as overwraps. Due to the fact that overwraps are subjected to sustained loads for an extended period during a mission, stress rupture failure is a major concern. It is therefore important to ascertain the reliability of these vessels by analysis, since the testing of each flight design cannot be completed on a practical time scale. The present paper examines specifically a Weibull statistics based stress rupture model and considers the various uncertainties associated with the model parameters. The paper also examines several reliability estimate measures that would be of use for the purpose of recertification and for qualifying flight worthiness of these vessels. Specifically, deterministic values for a point estimate, mean estimate and 90/95 percent confidence estimates of the reliability are all examined for a typical flight quality vessel under constant stress. The mean and the 90/95 percent confidence estimates are computed using Monte-Carlo simulation techniques by assuming distribution statistics of model parameters based also on simulation and on the available data, especially the sample sizes represented in the data. The data for the stress rupture model are obtained from the Lawrence Livermore National Laboratories (LLNL) stress rupture testing program, carried out for the past 35 years. Deterministic as well as probabilistic sensitivities are examined.

  16. Stress analysis of advanced attack helicopter composite main rotor blade root end lug

    Science.gov (United States)

    Baker, D. J.

    1982-01-01

    Stress analysis of the Advanced Attack Helicopter (AAH) composite main rotor blade root end lug is described. The stress concentration factor determined from a finite element analysis is compared to an empirical value used in the lug design. The analysis and test data indicate that the stress concentration is primarily a function of configuration and independent of the range of material properties typical of Kevlar-49/epoxy and glass epoxy.

  17. An experimental study on laser drilling and cutting of composite materials for the aerospace industry using excimer and CO2 sources

    Science.gov (United States)

    dell'Erba, M.; Galantucci, L. M.; Miglietta, S.

    This paper reports on the results of research which investigated the potential for the application of an excimer laser in the field of composite material drilling and cutting, by comparing this technology with that using CO2 sources. In particular, the scope of the work was to check whether the interaction between excimer lasers and composite materials, whose characteristic feature is the absence of thermal transfer, could yield better results than those obtainable with CO2 sources once heat transfer-induced difficulties had been eliminated. The materials selected for the experiments were multilayer composites having an epoxy resin matrix (65 percent in volume), with aramid fiber (Kevlar), carbon fiber and glass fiber as reinforcing materials, all of considerable interest for the aerospace industry. Optimal operational parameters were identified in relation to each source with a view to obtaining undersize holes or through cuts exhibiting severed areas of good quality. A comparison between the two types of processing carried out show that rims processed by excimer lasers are of better quality - particularly so with Kevlar - whereas the ablation rate is undoubtedly rather low compared with the CO2 technology.

  18. Poling of PVDF matrix composites for integrated structural load sensing

    Science.gov (United States)

    Haghiashtiani, Ghazaleh; Greminger, Michael A.; Zhao, Ping

    2014-03-01

    The purpose of this study is to create and evaluate a smart composite structure that can be used for integrated load sensing and structural health monitoring. In this structure, PVDF films are used as the matrix material instead of epoxy resin or other thermoplastics. The reinforcements are two layers of carbon fiber with one layer of Kevlar separating them. Due to the electrical conductivity properties of carbon fiber and the dielectric effect of Kevlar, the structure acts as a capacitor. Furthermore, the piezoelectric properties of the PVDF matrix can be used to monitor the response of the structure under applied loads. In order to exploit the piezoelectric properties of PVDF, the PVDF material must be polarized to align the dipole moments of its crystalline structure. The optimal condition for poling the structure was found by performing a 23 factorial design of experiment (DoE). The factors that were studied in DoE were temperature, voltage, and duration of poling. Finally, the response of the poled structure was monitored by exposing the samples to an applied load.

  19. 26 CFR 1.936-10 - Qualified investments.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 10 2010-04-01 2010-04-01 false Qualified investments. 1.936-10 Section 1.936... (CONTINUED) INCOME TAXES Possessions of the United States § 1.936-10 Qualified investments. (a) In general. [Reserved] (b) Qualified investments in Puerto Rico. [Reserved] (c) Qualified investment in certain...

  20. Enhancement of mechanical and electrical properties of continuous-fiber-reinforced epoxy composites with stacked graphene

    OpenAIRE

    Naveh, Naum; Shepelev, Olga; Kenig, Samuel

    2017-01-01

    Impregnation of expandable graphite (EG) after thermal treatment with an epoxy resin containing surface-active agents (SAAs) enhanced the intercalation of epoxy monomer between EG layers and led to further exfoliation of the graphite, resulting in stacks of few graphene layers, so-called “stacked” graphene (SG). This process enabled electrical conductivity of cured epoxy/SG composites at lower percolation thresholds, and improved thermo-mechanical properties were measured with either Kevlar, ...

  1. Optimization of Composite Material System and Lay-up to Achieve Minimum Weight Pressure Vessel

    Science.gov (United States)

    Mian, Haris Hameed; Wang, Gang; Dar, Uzair Ahmed; Zhang, Weihong

    2013-10-01

    The use of composite pressure vessels particularly in the aerospace industry is escalating rapidly because of their superiority in directional strength and colossal weight advantage. The present work elucidates the procedure to optimize the lay-up for composite pressure vessel using finite element analysis and calculate the relative weight saving compared with the reference metallic pressure vessel. The determination of proper fiber orientation and laminate thickness is very important to decrease manufacturing difficulties and increase structural efficiency. In the present work different lay-up sequences for laminates including, cross-ply [ 0 m /90 n ] s , angle-ply [ ±θ] ns , [ 90/±θ] ns and [ 0/±θ] ns , are analyzed. The lay-up sequence, orientation and laminate thickness (number of layers) are optimized for three candidate composite materials S-glass/epoxy, Kevlar/epoxy and Carbon/epoxy. Finite element analysis of composite pressure vessel is performed by using commercial finite element code ANSYS and utilizing the capabilities of ANSYS Parametric Design Language and Design Optimization module to automate the process of optimization. For verification, a code is developed in MATLAB based on classical lamination theory; incorporating Tsai-Wu failure criterion for first-ply failure (FPF). The results of the MATLAB code shows its effectiveness in theoretical prediction of first-ply failure strengths of laminated composite pressure vessels and close agreement with the FEA results. The optimization results shows that for all the composite material systems considered, the angle-ply [ ±θ] ns is the optimum lay-up. For given fixed ply thickness the total thickness of laminate is obtained resulting in factor of safety slightly higher than two. Both Carbon/epoxy and Kevlar/Epoxy resulted in approximately same laminate thickness and considerable percentage of weight saving, but S-glass/epoxy resulted in weight increment.

  2. 7 CFR 4290.110 - Qualified management.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Qualified management. 4290.110 Section 4290.110... Qualifications for the RBIC Program Organizing A Rbic § 4290.110 Qualified management. An Applicant must show, to the satisfaction of the Secretary, that its current or proposed management team is qualified and has...

  3. Vibro-acoustic analysis of composite plates

    International Nuclear Information System (INIS)

    Sarigül, A S; Karagözlü, E

    2014-01-01

    Vibro-acoustic analysis plays a vital role on the design of aircrafts, spacecrafts, land vehicles and ships produced from thin plates backed by closed cavities, with regard to human health and living comfort. For this type of structures, it is required a coupled solution that takes into account structural-acoustic interaction which is crucial for sensitive solutions. In this study, coupled vibro-acoustic analyses of plates produced from composite materials have been performed by using finite element analysis software. The study has been carried out for E-glass/Epoxy, Kevlar/Epoxy and Carbon/Epoxy plates with different ply angles and numbers of ply. The effects of composite material, ply orientation and number of layer on coupled vibro-acoustic characteristics of plates have been analysed for various combinations. The analysis results have been statistically examined and assessed

  4. Vibro-acoustic analysis of composite plates

    Science.gov (United States)

    Sarigül, A. S.; Karagözlü, E.

    2014-03-01

    Vibro-acoustic analysis plays a vital role on the design of aircrafts, spacecrafts, land vehicles and ships produced from thin plates backed by closed cavities, with regard to human health and living comfort. For this type of structures, it is required a coupled solution that takes into account structural-acoustic interaction which is crucial for sensitive solutions. In this study, coupled vibro-acoustic analyses of plates produced from composite materials have been performed by using finite element analysis software. The study has been carried out for E-glass/Epoxy, Kevlar/Epoxy and Carbon/Epoxy plates with different ply angles and numbers of ply. The effects of composite material, ply orientation and number of layer on coupled vibro-acoustic characteristics of plates have been analysed for various combinations. The analysis results have been statistically examined and assessed.

  5. Yarn Pull-Out as a Mechanism for Dissipation of Ballistic Impact Energy in Kevlar KM-2 Fabric, Part 1: Quasi-Static Characterization of Yarn Pull-Out

    National Research Council Canada - National Science Library

    Kirkwood, Keith

    2004-01-01

    .... This study reports the effects of fabric length, number of yarns pulled, arrangement of yarns, and transverse tension on the force-displacement curves for yarn pull-out tests on Kevlar KM-2 fabric...

  6. High energy ballistic and fracture comparison between multilayered armor systems using non-woven curaua fabric composites and aramid laminates

    Directory of Open Access Journals (Sweden)

    Fábio de Oliveira Braga

    2017-10-01

    Full Text Available For personal protection against high kinetic energy projectiles, multilayered armor systems (MAS are usually the best option. They combine synergistically the properties of different materials such as ceramics, composites and metals. In the present work, ballistic tests were performed to evaluate multilayered armor systems (MAS using curaua non-woven fabric epoxy composites as second layer. A comparison to a MAS using aramid (Kevlar™ fabric laminates was made. The results showed that the curaua non-woven fabric composites are suitable to the high ballistic applications, and are promising substitutes for aramid fabric laminates. Keywords: Composite, Natural fiber, Curaua fiber, Non-woven fabric, Aramid laminate, Ballistic test

  7. Structurally integrated fiber optic damage assessment system for composite materials.

    Science.gov (United States)

    Measures, R M; Glossop, N D; Lymer, J; Leblanc, M; West, J; Dubois, S; Tsaw, W; Tennyson, R C

    1989-07-01

    Progress toward the development of a fiber optic damage assessment system for composite materials is reported. This system, based on the fracture of embedded optical fibers, has been characterized with respect to the orientation and location of the optical fibers in the composite. Together with a special treatment, these parameters have been tailored to yield a system capable of detecting the threshold of damage for various impacted Kevlar/epoxy panels. The technique has been extended to measure the growth of a damage region which could arise from either impact, manufacturing flaws, or static overloading. The mechanism of optical fiber fracture has also been investigated. In addition, the influence of embedded optical fibers on the tensile and compressive strength of the composite material has been studied. Image enhanced backlighting has been shown to be a powerful and convenient method of assessing internal damage to translucent composite materials.

  8. Composite Stress Rupture NDE Research and Development Project (Kevlar[R] and Carbon)

    Science.gov (United States)

    Saulsberry, Regor

    2010-01-01

    The objective was to develop and demonstrate nondestructive evaluation (NDE) techniques capable of assessing stress rupture related strength degradation for carbon composite pressure vessels, either in a structural health monitoring (SHM) or periodic inspection mode.

  9. Highly qualified in the Czech Republic

    Directory of Open Access Journals (Sweden)

    Renata Čuhlová

    2017-05-01

    Full Text Available The paper aims to analyse the current situation of the highly qualified in the Czech Republic applying the ISCO qualification. Previous studies suggest that educational attainment has an important impact on labour market performance and national competitiveness. Data analyses approved that highly qualified workforce positively influences economic situation of the EU–15 Member States they work in. However, this hypothesis was disapproved for the EU–10+3 Member States joining the EU after 2004. The difference can be explained by the various stage in convergence process since some New Member States are still in transformation period. We positively appraise the significant growth of fraction of the highly qualified in the Czech Republic since 2004, especially in the major group Professionals involving the most qualified workforce. The same trend happened also for the highly qualified foreigners in the Czech Republic, however their attracting still remains a challenge.

  10. Predicting the mechanical behaviour of Kevlar/epoxy and carbon/epoxy filament-wound tubes

    Science.gov (United States)

    Cazeneuve, C.; Joguet, P.; Maile, J. C.; Oytana, C.

    1992-11-01

    The axial, hoop and shear moduli and failure conditions of carbon/epoxy and Kevlar/epoxy filament-wound tubes have been determined through respective applications of internal pressure, tension and torsion. The introduction in the laminated plate theory of a gradual reduction in individual moduli makes it possible to overcome the limitations of the theory and enables accurate predictions to be made of the linear and non-linear stress/strain curves of 90 deg +/- 0/90 deg tubes. The existence of a dominant layer in the failure of the multilayered tubes has been shown experimentally. When associated with a failure criterion applied to the dominant layer, the new model permits the prediction of tube failure. Agreement between calculated and experimental data is better than 5 percent.

  11. Performances of Kevlar and Polyethylene as radiation shielding on-board the International Space Station in high latitude radiation environment.

    Science.gov (United States)

    Narici, Livio; Casolino, Marco; Di Fino, Luca; Larosa, Marianna; Picozza, Piergiorgio; Rizzo, Alessandro; Zaconte, Veronica

    2017-05-10

    Passive radiation shielding is a mandatory element in the design of an integrated solution to mitigate the effects of radiation during long deep space voyages for human exploration. Understanding and exploiting the characteristics of materials suitable for radiation shielding in space flights is, therefore, of primary importance. We present here the results of the first space-test on Kevlar and Polyethylene radiation shielding capabilities including direct measurements of the background baseline (no shield). Measurements are performed on-board of the International Space Station (Columbus modulus) during the ALTEA-shield ESA sponsored program. For the first time the shielding capability of such materials has been tested in a radiation environment similar to the deep-space one, thanks to the feature of the ALTEA system, which allows to select only high latitude orbital tracts of the International Space Station. Polyethylene is widely used for radiation shielding in space and therefore it is an excellent benchmark material to be used in comparative investigations. In this work we show that Kevlar has radiation shielding performances comparable to the Polyethylene ones, reaching a dose rate reduction of 32 ± 2% and a dose equivalent rate reduction of 55 ± 4% (for a shield of 10 g/cm 2 ).

  12. 26 CFR 1.30-1 - Definition of qualified electric vehicle and recapture of credit for qualified electric vehicle.

    Science.gov (United States)

    2010-04-01

    ... qualified electric vehicle. A qualified electric vehicle is a motor vehicle that meets the requirements of section 30(c). Accordingly, a qualified electric vehicle does not include any motor vehicle that has ever been used (for either personal or business use) as a non-electric vehicle. (b) Recapture of credit for...

  13. 11 CFR 9002.11 - Qualified campaign expense.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Qualified campaign expense. 9002.11 Section 9002.11 Federal Elections FEDERAL ELECTION COMMISSION PRESIDENTIAL ELECTION CAMPAIGN FUND: GENERAL ELECTION FINANCING DEFINITIONS § 9002.11 Qualified campaign expense. (a) Qualified campaign expense means...

  14. 11 CFR 9032.9 - Qualified campaign expense.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Qualified campaign expense. 9032.9 Section 9032.9 Federal Elections FEDERAL ELECTION COMMISSION PRESIDENTIAL ELECTION CAMPAIGN FUND: PRESIDENTIAL PRIMARY MATCHING FUND DEFINITIONS § 9032.9 Qualified campaign expense. (a) Qualified campaign expense...

  15. Investigation into Composites Property Effect on the Forming Limits of Multi-Layer Hybrid Sheets Using Hydroforming Technology

    Science.gov (United States)

    Liu, Shichen; Lang, Lihui; Guan, Shiwei; Alexandrov, Seigei; Zeng, Yipan

    2018-04-01

    Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydroforming technology are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

  16. The Fabrication of Qualified Citizens

    DEFF Research Database (Denmark)

    Andrade-Molina, Melissa

    2017-01-01

    a rhizomatic analytical move, a historization of the present is deployed to map the fabrication of the desired qualified citizen in Chile. The analysis evidences the (re)production of dominant narratives about the “qualified citizen” are and have been entangled with the functioning of school geometry...

  17. Seawater infiltration effect on thermal degradation of fiber reinforced epoxy composites

    Science.gov (United States)

    Ibrahim, Mohd Haziq Izzuddin bin; Hassan, Mohamad Zaki bin; Ibrahim, Ikhwan; Rashidi, Ahmad Hadi Mohamed; Nor, Siti Fadzilah M.; Daud, Mohd Yusof Md

    2018-05-01

    Seawater salinity has been associated with the reduction of polymer structure durability. The aim of this study is to investigate the change in thermal degradation of fiber reinforced epoxy composite due to the presence of seawater. Carbon fiber, carbon/kevlar, fiberglass, and jute that reinforced with epoxy resin was laminated through hand-layup technique. Initially, these specimen was sectioned to 5×5 mm dimension, then immersed in seawater and distilled water at room temperature until it has thoroughly saturated. Following, the thermal degradation analysis using Differential Scanning Calorimetry (DSC), the thermic changes due to seawater infiltration was defined. The finding shows that moisture absorption reduces the glass transition temperature (Tg) of fiber reinforced epoxy composite. However, the glass transition temperature (Tg) of seawater infiltrated laminate composite is compareable with distilled water infiltrated laminate composite. The carbon fiber reinfored epoxy has the highest glass transition temperature out of all specimen.

  18. Computational Investigation of Shock-Mitigation Efficacy of Polyurea When Used in a Combat Helmet

    Science.gov (United States)

    2012-01-01

    instance, polyureas are frequently used as: . tough, abrasion-resistant, corrosion-resistant, durable and impact-resistant ( epoxy /rubber replacement) spray...are typically discretized within a coupled Figure 2. The ACH with its labeled main components: Kevlar -phenolic composite outer shell, interior...suspensions pads and a restraint (chin strap) system Suspension Pads Source: Grujicic et al. (2010d) Kevlar -Phenolic Composite Shell Restraint System (Chin

  19. PELE侵彻复合装甲数值模拟%Numerical Simulation of PELE Penetrating Composite Armor

    Institute of Scientific and Technical Information of China (English)

    李干; 王志军; 王妍; 李硕

    2016-01-01

    为了探究横向增强型侵彻体(PELE)侵彻复合装甲后的毁伤效果,采用显式非线性动力分析软件AUTODYN,对装填特氟龙(聚四氟乙烯)的侵彻膨胀弹以900 m/s着靶速度侵彻复合靶板的过程进行了数值模拟,得到PELE弹对复合靶侵彻破坏效应及相关参数.结果表明:聚碳酸酯(玻璃纤维)、聚氨酯(泡沫塑料)与凯夫拉复合装甲的结构均被PELE的横向效应所破坏;复合装甲的夹心材料不同,靶板的破坏程度也不尽相同;复合装甲能对PELE的横向效应起到一定的抑制作用,而凯夫拉材料抑制作用较好.%In order to analyze the damage effect of the penetrator with enhanced lateral efficiency( PELE) penetrating composite armor, an explicit nonlinear dynamic analysis software AUTODYN was used to simulate the process of PELE filled with Teflon( polytetrafluoroethylene) penetrating composite target plate using the speed of 900 m/s, and the destructive effect and relevant parameters of PELE penetrating composite armor were obtained finally. The result shows that the composite armor constructed by polycarbonate( glass fibre) ,polyurethane and Kevlar is damaged seriously by lateral efficiency of PELE. The different composite-armors have different damage. The composite armor has definite inhibitory effect on lateral efficiency of PELE,and the inhibitory effect of Kevlar is better.

  20. Effects of temperature and loading speed on interface-dominated strength in fibre/polymer composites: An evaluation for in-situ environment

    International Nuclear Information System (INIS)

    Sethi, Sanghamitra; Rathore, Dinesh Kumar; Ray, Bankim Chandra

    2015-01-01

    Graphical abstract: Some microcracks turn to potential cracks at low loading rates and cause significant reduction in interlaminar shear strength of the composite system while as the loading rate increases the time available to propagate the microcracks is less. This can be attributed to higher ILSS at higher loading rates at these above-ambient temperatures. - Highlights: • Effect of temperature and loading rate has been studied. • Three different types of fibres are used for fabrication. • Flexural and fractography behaviour were studied. • T g was affected by types of fibre and matrix used. - Abstract: The present investigation intends to study the influence of crosshead velocity and in-situ environmental conditioning i.e. high temperature and cryogenic temperature on micromechanical performance of glass fibre/epoxy, carbon fibre/epoxy and Kevlar fibre/epoxy polymer composites. 3-point short beam shear tests were conducted on the conditioned specimens to evaluate the interfacial properties and failure modes which are related to mechanical properties of the composites. The effect of crosshead velocity (within the range 1-10 3 mm/min) on the interlaminar shear strength (ILSS) of all the three composite systems at different temperatures was studied. The glass transition temperature (T g ) of conditioned samples were measured by differential scanning calorimetry (DSC) in the temperature range of 25 °C to 150 °C temperature. At 1 mm/min loading rate, for both glass/epoxy and carbon/epoxy composites maximum increase in ILSS value was about 85.72% with respect to ambient, while for Kevlar/epoxy composite 31.77% reduction in ILSS was observed at -100 °C temperature

  1. Composite Overwrap Pressure Vessels: Mechanics and Stress Rupture Lifting Philosophy

    Science.gov (United States)

    Thesken, John C.; Murthy, Pappu L. N.; Phoenix, S. L.

    2009-01-01

    The NASA Engineering and Safety Center (NESC) has been conducting an independent technical assessment to address safety concerns related to the known stress rupture failure mode of filament wound pressure vessels in use on Shuttle and the International Space Station. The Shuttle s Kevlar-49 (DuPont) fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar-49 filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of load sharing liners and the complex manufacturing procedures, the state of actual fiber stress in flight hardware and test articles is not clearly known. Indeed nonconservative life predictions have been made where stress rupture data and lifing procedures have ignored the contribution of the liner in favor of applied pressure as the controlling load parameter. With the aid of analytical and finite element results, this paper examines the fundamental mechanical response of composite overwrapped pressure vessels including the influence of elastic plastic liners and degraded/creeping overwrap properties. Graphical methods are presented describing the non-linear relationship of applied pressure to Kevlar-49 fiber stress/strain during manufacturing, operations and burst loadings. These are applied to experimental measurements made on a variety of vessel systems to demonstrate the correct calibration of fiber stress as a function of pressure. Applying this analysis to the actual qualification burst data for Shuttle flight hardware revealed that the nominal fiber stress at burst was in some cases 23 percent lower than what had previously been used to predict stress rupture life. These results motivate a detailed discussion of the appropriate stress rupture lifing philosophy for COPVs including the correct transference of stress rupture life data between dissimilar vessels and test articles.

  2. Composite Overwrap Pressure Vessels: Mechanics and Stress Rupture Lifing Philosophy

    Science.gov (United States)

    Thesken, John C.; Murthy, Pappu L. N.; Phoenix, Leigh

    2007-01-01

    The NASA Engineering and Safety Center (NESC) has been conducting an independent technical assessment to address safety concerns related to the known stress rupture failure mode of filament wound pressure vessels in use on Shuttle and the International Space Station. The Shuttle's Kevlar-49 fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar-49 filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of load sharing liners and the complex manufacturing procedures, the state of actual fiber stress in flight hardware and test articles is not clearly known. Indeed non-conservative life predictions have been made where stress rupture data and lifing procedures have ignored the contribution of the liner in favor of applied pressure as the controlling load parameter. With the aid of analytical and finite element results, this paper examines the fundamental mechanical response of composite overwrapped pressure vessels including the influence of elastic-plastic liners and degraded/creeping overwrap properties. Graphical methods are presented describing the non-linear relationship of applied pressure to Kevlar-49 fiber stress/strain during manufacturing, operations and burst loadings. These are applied to experimental measurements made on a variety of vessel systems to demonstrate the correct calibration of fiber stress as a function of pressure. Applying this analysis to the actual qualification burst data for Shuttle flight hardware revealed that the nominal fiber stress at burst was in some cases 23% lower than what had previously been used to predict stress rupture life. These results motivate a detailed discussion of the appropriate stress rupture lifing philosophy for COPVs including the correct transference of stress rupture life data between dissimilar vessels and test articles.

  3. 21 CFR 516.141 - Qualified expert panels.

    Science.gov (United States)

    2010-04-01

    ... choose members for the qualified expert panel in accordance with selection criteria listed in paragraph... whether the proposed qualified expert panel meets the selection criteria prior to the panel beginning its... Committee Act, as amended, 5 U.S.C. App. (b) Criteria for the selection of a qualified expert panel. (1) A...

  4. Evaluation of Impact Strength of Epoxy Based Hybrid Composites Reinforced with E-Glass/Kevlar 49

    OpenAIRE

    Jogi , Subhan Ali; Moazam Baloch , Muhammad; Chandio , Ali ,; Memon , Iftikhar Ahmed; Chandio , Ghulaqm Sarwar

    2017-01-01

    International audience; In hybridization different fibers are stacked layer by layer to produce laminates have specific strength and stiffness and employed in light weight high strength applications. Physically mean fabricated hybrid composites used in aerospace, under water, body armors and armed forces establishment. In present work drop-weight impact response of hybrid composites were investigated by making laminates of hybrid composites. In Hybridization layers of E-glass (roving) and Kev...

  5. Power generation from base excitation of a Kevlar composite beam with ZnO nanowires

    Science.gov (United States)

    Malakooti, Mohammad H.; Hwang, Hyun-Sik; Sodano, Henry A.

    2015-04-01

    One-dimensional nanostructures such as nanowires, nanorods, and nanotubes with piezoelectric properties have gained interest in the fabrication of small scale power harvesting systems. However, the practical applications of the nanoscale materials in structures with true mechanical strengths have not yet been demonstrated. In this paper, piezoelectric ZnO nanowires are integrated into the fiber reinforced polymer composites serving as an active phase to convert the induced strain energy from ambient vibration into electrical energy. Arrays of ZnO nanowires are grown vertically aligned on aramid fibers through a low-cost hydrothermal process. The modified fabrics with ZnO nanowires whiskers are then placed between two carbon fabrics as the top and the bottom electrodes. Finally, vacuum resin transfer molding technique is utilized to fabricate these multiscale composites. The fabricated composites are subjected to a base excitation using a shaker to generate charge due to the direct piezoelectric effect of ZnO nanowires. Measuring the generated potential difference between the two electrodes showed the energy harvesting application of these multiscale composites in addition to their superior mechanical properties. These results propose a new generation of power harvesting systems with enhanced mechanical properties.

  6. 33 CFR 155.1026 - Qualified individual and alternate qualified individual.

    Science.gov (United States)

    2010-07-01

    ... familiar with the implementation of the vessel response plan; and (4) Be trained in the responsibilities of... vessel may designate an organization to fulfill the role of the qualified individual and alternate...

  7. Stress transfer of a Kevlar 49 fiber pullout test studied by micro-Raman spectroscopy.

    Science.gov (United States)

    Lei, Zhenkun; Wang, Quan; Qiu, Wei

    2013-06-01

    The interfacial stress transfer behavior of a Kevlar 49 aramid fiber-epoxy matrix was studied with fiber pullout tests, the fibers of which were stretched by a homemade microloading device. Raman spectra on the embedded fiber were recorded by micro-Raman spectroscopy, under different strain levels. Then, the fiber axial stress was obtained by the relationship between the stress and Raman shift of the aramid fiber. Experimental results revealed that the fiber axial stress increased significantly with the load. The shear stress concentration occurred at the fiber entry to the epoxy resin. Thus, interfacial friction stages exist in the debonded fiber segment, and the interfacial friction shear stress is constant within one stage. The experimental results are consistent with the theoretical model predictions.

  8. Stiffness Analysis of the Sarafix External Fixator based on Stainless Steel and Composite Material

    Directory of Open Access Journals (Sweden)

    Nedim Pervan

    2015-11-01

    Full Text Available This paper describes a structural analysis of the CAD model three versions fixators Sarafix which is to explore the possibility of introducing composite materials in the construction of the connecting rod fixators comparing values of displacement and stiffness at characteristic structure points. Namely, we have investigated the constructional performance of fixators Sarafix with a connecting rod formed from three different composite materials, the same matrix (epoxy resin with three different types of fibers (E glass, kevlar 49 and carbonM55J. The results of the structural analysis fixators Sarafix with a connecting rod made of composite materials are compared with the results of tubular connecting rod fixators made of stainless steel. After comparing the results, from the aspect of stiffness, we gave the final considerations about composite material which provides an adequate substitution for the existing material.

  9. Supply Inventory Management: Evaluation of the Defense Supply Center Columbus Qualified Products List and Qualified Manufacturers List Program

    National Research Council Canada - National Science Library

    2002-01-01

    ... was transitioned from the Military Departments. The Defense Supply Center Columbus currently has management responsibility for over 300 Qualified Products Lists and 4 Qualified Manufacturers Lists...

  10. Reflections on the newly qualified social worker's journey : From university training to qualified practice

    OpenAIRE

    Walker, Clare

    2014-01-01

    This qualitative research study explores the experience of graduating social workers making the transition from university training into work as qualified social work practitioners. Most studies in this area look at the practice readiness of the newly qualified professional. This study looks at the participants’ experience in the work place. How do participants experience this journey of transition? What skills, particularly reflective practice and supervision, learned in training, are import...

  11. 33 CFR 154.1026 - Qualified individual and alternate qualified individual.

    Science.gov (United States)

    2010-07-01

    ... alternate must: (1) Be located in the United States; (2) Speak fluent English; (3) Be familiar with the... facility may designate an organization to fulfill the role of the qualified individual and the alternate...

  12. A dendrite-suppressing composite ion conductor from aramid nanofibres.

    Science.gov (United States)

    Tung, Siu-On; Ho, Szushen; Yang, Ming; Zhang, Ruilin; Kotov, Nicholas A

    2015-01-27

    Dendrite growth threatens the safety of batteries by piercing the ion-transporting separators between the cathode and anode. Finding a dendrite-suppressing material that combines high modulus and high ionic conductance has long been considered a major technological and materials science challenge. Here we demonstrate that these properties can be attained in a composite made from Kevlar-derived aramid nanofibres assembled in a layer-by-layer manner with poly(ethylene oxide). Importantly, the porosity of the membranes is smaller than the growth area of the dendrites so that aramid nanofibres eliminate 'weak links' where the dendrites pierce the membranes. The aramid nanofibre network suppresses poly(ethylene oxide) crystallization detrimental for ion transport, giving a composite that exhibits high modulus, ionic conductivity, flexibility, ion flux rates and thermal stability. Successful suppression of hard copper dendrites by the composite ion conductor at extreme discharge conditions is demonstrated, thereby providing a new approach for the materials engineering of solid ion conductors.

  13. Composite material bend-twist coupling for wind turbine blade applications

    Science.gov (United States)

    Walsh, Justin M.

    Current efforts in wind turbine blade design seek to employ bend-twist coupling of composite materials for passive power control by twisting blades to feather. Past efforts in this area of study have proved to be problematic, especially in formulation of the bend-twist coupling coefficient alpha. Kevlar/epoxy, carbon/epoxy and glass/epoxy specimens were manufactured to study bend-twist coupling, from which numerical and analytical models could be verified. Finite element analysis was implemented to evaluate fiber orientation and material property effects on coupling magnitude. An analytical/empirical model was then derived to describe numerical results and serve as a replacement for the commonly used coupling coefficient alpha. Through the results from numerical and analytical models, a foundation for aeroelastic design of wind turbines blades utilizing biased composite materials is provided.

  14. Etude de l'effet du vieillissement sur les proprietes d'un tissu en melange KevlarRTM-PBI utilise dans le revetement exterieur des habits de protection contre le feu

    Science.gov (United States)

    Arrieta, Carlos

    The aim of this work is to study and model the effect of three aging factors, temperature, humidity and light radiation, on the properties of a fabric made of a blend of KevlarRTM and PBI fibers frequently used to manufacture fire-protective garments. Accelarated-aging treatments carried out at carefully chosen conditions for the three factors resulted in a sizeable loss of mechanical performance. The breaking force of both the fabric and the yarns extracted from it decreases to less than 50% after one month of continuous exposure. X-ray diffraction (XRD) tests performed on thermally-aged samples indicated an increase of the crystallinity of the fabric, whereas the disappearance of Raman spectral lines suggested instead a reduction of the crystallinity following thermal aging. To explain these seemingly contradictory results, a hypothesis was introduced, stating that two different processes occurred simultaneously during thermal aging. The first one, an increase of size of the crystallites in the direction of the fibers' axis, accounted for the increase in crystallinity observed in XRD tests. The second one, an increase in the gap separating lamellar crystallites that causes a non-measurable reduction of the crystallinity of the sample, was highlighted by the Raman analyses. The results of the dielectric spectroscopy analyses carried out on thermally-aged samples confirmed the XRD results showing a significant change in the Kevlar's morphology during thermal aging. Despite the important decrease of the breaking force that ensued thermal aging, no evidence of a chemical structure modification of KevlarRTM was found. On the other hand, differential thermal analyses conducted on thermally aged fabric samples indicated a reduction of the glass transition temperature of the other component of the blend, namely the PBI, a fact that suggests a decrease of molecular weight after thermal aging. Infrared spectroscopy analyses performed on samples exposed to high humidity

  15. Fique Fabric: A Promising Reinforcement for Polymer Composites

    Directory of Open Access Journals (Sweden)

    Sergio Neves Monteiro

    2018-02-01

    Full Text Available A relatively unknown natural fiber extracted from the leaves of the fique plant, native of the South American Andes, has recently shown potential as reinforcement of polymer composites for engineering applications. Preliminary investigations indicated a promising substitute for synthetic fibers, competing with other well-known natural fibers. The fabric made from fique fibers have not yet been investigated as possible composite reinforcement. Therefore, in the present work a more thorough characterization of fique fabric as a reinforcement of composites with a polyester matrix was performed. Thermal mechanical properties of fique fabric composites were determined by dynamic mechanical analysis (DMA. The ballistic performance of plain woven fique fabric-reinforced polyester matrix composites was investigated as a second layer in a multilayered armor system (MAS. The results revealed a sensible improvement in thermal dynamic mechanical behavior. Both viscoelastic stiffness and glass transition temperature were increased with the amount of incorporated fique fabric. In terms of ballistic results, the fique fabric composites present a performance similar to that of the much stronger KevlarTM as an MAS second layer with the same thickness. A cost analysis indicated that armor vests with fique fabric composites as an MAS second layer would be 13 times less expensive than a similar creation made with Kevlar™.

  16. Optimum design of brake friction material using hybrid entropy-GRA approach

    Directory of Open Access Journals (Sweden)

    Kumar Naresh

    2016-01-01

    Full Text Available The effect of Kevlar and natural fibres on the performance of brake friction materials was evaluated. Four friction material specimens were developed by varying the proportion of Kevlar and natural fibres. Two developed composite contained 5-10 wt.% of Kevlar fibre while in the other two the Kevlar fibre was replaced with same amount of natural fibre. SAE J661 protocol was used for the assessment of the tribological properties on a Chase testing machine. Result shows that the specimens containing Kevlar fibres shows higher friction and wear performance, whereas Kevlar replacement with natural fibre resulted in improved fade, recovery and friction fluctuations. Further hybrid entropy-GRA (grey relation analysis approach was applied to select the optimal friction materials using various performance defining attributes (PDA including friction, wear, fade, recovery, friction fluctuations and cost. The friction materials with 10 wt% of natural fibre exhibited the best overall quality.

  17. 11 CFR 9004.4 - Use of payments; examples of qualified campaign expenses and non-qualified campaign expenses.

    Science.gov (United States)

    2010-01-01

    ... 11 Federal Elections 1 2010-01-01 2010-01-01 false Use of payments; examples of qualified campaign expenses and non-qualified campaign expenses. 9004.4 Section 9004.4 Federal Elections FEDERAL ELECTION COMMISSION PRESIDENTIAL ELECTION CAMPAIGN FUND: GENERAL ELECTION FINANCING ENTITLEMENT OF ELIGIBLE CANDIDATES...

  18. Nominal Group as Qualifier to "Someone"

    Science.gov (United States)

    Sujatna, Eva Tuckyta Sari; Wahyuni, Sri

    2017-01-01

    The paper titled "Nominal Group as Qualifier to 'Someone'" investigated types of qualifiers which are embedded to the head "someone" in a nominal group. This research was conducted in the light of Systemic Functional Linguistics analysis. The data was analyzed, classified then described using descriptive qualitative method.…

  19. Effect of Mesoscale and Multiscale Modeling on the Performance of Kevlar Woven Fabric Subjected to Ballistic Impact: A Numerical Study

    Science.gov (United States)

    Jia, Xin; Huang, Zhengxiang; Zu, Xudong; Gu, Xiaohui; Xiao, Qiangqiang

    2013-12-01

    In this study, an optimal finite element model of Kevlar woven fabric that is more computational efficient compared with existing models was developed to simulate ballistic impact onto fabric. Kevlar woven fabric was modeled to yarn level architecture by using the hybrid elements analysis (HEA), which uses solid elements in modeling the yarns at the impact region and uses shell elements in modeling the yarns away from the impact region. Three HEA configurations were constructed, in which the solid element region was set as about one, two, and three times that of the projectile's diameter with impact velocities of 30 m/s (non-perforation case) and 200 m/s (perforation case) to determine the optimal ratio between the solid element region and the shell element region. To further reduce computational time and to maintain the necessary accuracy, three multiscale models were presented also. These multiscale models combine the local region with the yarn level architecture by using the HEA approach and the global region with homogenous level architecture. The effect of the varying ratios of the local and global area on the ballistic performance of fabric was discussed. The deformation and damage mechanisms of fabric were analyzed and compared among numerical models. Simulation results indicate that the multiscale model based on HEA accurately reproduces the baseline results and obviously decreases computational time.

  20. 30 CFR 75.155 - Qualified hoisting engineer; qualifications.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Qualified hoisting engineer; qualifications. 75... Persons § 75.155 Qualified hoisting engineer; qualifications. (a)(1) A person is a qualified hoisting engineer within the provisions of subpart O of this part, for the purpose of operating a steam-driven hoist...

  1. Fabrication of Hydrophobic Membrane for the Separation of n-Hexane/Water Mixture Using Novel Oleophilic Nanoparticle and Kevlar Fabric, as a Superior Support

    Directory of Open Access Journals (Sweden)

    Hanieh Karimnezhad

    2017-07-01

    Full Text Available The fabrication of functionalized membranes with hydrophobic/oleophilic surfaces for the elimination of n-hexane from water using para-aminobenzoate alumoxane, boehmite-epoxide and a novel nanoparticle, i.e., Stearate Alumoxane by a simple coating technique, is reported here. FTIR was used to characterize nanoparticles. SEM and contact angle measurement analyses were used to identify the nanocomposite membranes. The concentrations of oil in permeate and retentate were measured by UV/vis spectrophotometer. The morphology of Stearate alumoxane nanoparticles was investigated by means of SEM images. The composed film of nanoparticles on the Kevlar fabric was hydrophobic with water contact angle of ~ 145° and oleophilic with oil contact angle of ~ 0º. In addition, the membranes retained stable hydrophobicity and high separation efficiency even after employing for 6 times. Applying these properties, a setup was considered using the functionalized Kevlar fabric to separate oil through down to a collector and leave water drops. Our batch filtration system was exclusively gravity-driven. The achieved separation system can separate the oily water mixture (with the concentration of 20 % (v/v n-hexane in water, effectively with a separation efficiency of 84%.

  2. Air Force Officer Qualifying Test Form T: Initial Item-, Test-, Factor-, and Composite-Level Analyses

    Science.gov (United States)

    2016-12-01

    used to qualify applicants for ROTC and OTS officer commissioning programs. The Pilot, Combat Systems Officer (CSO), and Air Battle Manager ( ABM ...AIR FORCE RESEARCH LABORATORY 711 HUMAN PERFORMANCE WING, AIRMAN SYSTEMS DIRECTORATE, WRIGHT-PATTERSON AIR FORCE BASE, OH 45433 AIR FORCE MATERIEL...Warfighter Interface Division Airman Systems Directorate This report is published in the interest of scientific and technical information exchange, and

  3. Qualified Census Tracts

    Data.gov (United States)

    Department of Housing and Urban Development — A Qualified Census Tract (QCT) is any census tract (or equivalent geographic area defined by the Census Bureau) in which at least 50% of households have an income...

  4. 26 CFR 1.132-9 - Qualified transportation fringes.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Qualified transportation fringes. 1.132-9... Qualified transportation fringes. (a) Table of contents. This section contains a list of the questions and answers in § 1.132-9. (1) General rules. Q-1. What is a qualified transportation fringe? Q-2. What is...

  5. Improvement of surface wettability and interfacial adhesion of poly-(p-phenylene terephthalamide) by incorporation of the polyamide benzimidazole segment

    International Nuclear Information System (INIS)

    Cai Renqin; Peng Tao; Wang Fengde; Ye Guangdou; Xu Jianjun

    2011-01-01

    In order to investigate the effect of the polyamide benzimidazole group on the surface wettability and interfacial adhesion of fiber/matrix composites, surface features of two kinds of aramid fibers, poly (p-phenylene terephthalamide) fiber (Kevlar-49) and poly-(polyamide benzimidazole-co-p-phenylene terephthalamide) (DAFIII), have been analyzed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and contact angle analysis (CAA) system, respectively. The results show that with the incorporation of the polyamide benzimidazole segment, more polar functional groups exist on DAFIII surface. The contact angles of water and diiodomethane on DAFIII surface get smaller. The surface free energy of DAFIII increases to 36.5 mJ/m 2 , which is 2.3% higher than that of Kevlar-49. In addition, DAFIII has a larger rough surface compared with that of Kevlar-49 due to different spinning processes. The interfacial shear strength (IFSS) of DAFIII/matrix composite is 25.7% higher than that of Kevlar-49/matrix composite, in agreement with the observed results from surface feature tests. SEM micrographs of failed micro-droplet specimens reveal a strong correlation between the fracture features and the observed test data.

  6. THE SYNERGISTIC EFFECT OF HYBRID FLAME RETARDANTS ON PYROLYSIS BEHAVIOUR OF HYBRID COMPOSITE MATERIALS

    Directory of Open Access Journals (Sweden)

    M. T. ALBDIRY

    2012-06-01

    Full Text Available The aim of this investigation is to comprehensively understand the polymeric composite behavior under direct fire sources. The synergistic effects of hybrid flame retardant material on inhabiting the pyrolysis of hybrid reinforced fibers, woven roving (0°- 45° carbon and kevlar (50/50 wt/wt, and an araldite resin composites were studied. The composites were synthesised and coated primarily by zinc borate (2ZnO.3B2O3.3.5H2O and modified by antimony trioxide (Sb2O3 with different amounts (10-30 wt% of flame retardant materials. In the experiments, the composite samples were exposed to a direct flame source generated by oxyacetylene flame (~3000ºC at variable exposure distances of 10-20 mm. The synergic flame retardants role of antimony trioxide and zinc borate on the composite surface noticeably improves the flame resistance of the composite which is attributed to forming a protective mass and heat barrier on the composite surface and increasing the melt viscosity.

  7. Qualified Empathy - Project Report 2015-16

    DEFF Research Database (Denmark)

    Austring, Bennye Düranc; Sørensen, Merete Cornet

    2016-01-01

    UCSJ-delen af den afsluttende rapport fra Nordplus-projektet "Qualified Empathy", der blev gennemført sammen med Metropolia, Helsinki, og NTNU, Trondheim, i 2015 og 15.......UCSJ-delen af den afsluttende rapport fra Nordplus-projektet "Qualified Empathy", der blev gennemført sammen med Metropolia, Helsinki, og NTNU, Trondheim, i 2015 og 15....

  8. Thermal Protective Coating for High Temperature Polymer Composites

    Science.gov (United States)

    Barron, Andrew R.

    1999-01-01

    The central theme of this research is the application of carboxylate-alumoxane nanoparticles as precursors to thermally protective coatings for high temperature polymer composites. In addition, we will investigate the application of carboxylate-alumoxane nanoparticle as a component to polymer composites. The objective of this research was the high temperature protection of polymer composites via novel chemistry. The significance of this research is the development of a low cost and highly flexible synthetic methodology, with a compatible processing technique, for the fabrication of high temperature polymer composites. We proposed to accomplish this broad goal through the use of a class of ceramic precursor material, alumoxanes. Alumoxanes are nano-particles with a boehmite-like structure and an organic periphery. The technical goals of this program are to prepare and evaluate water soluble carboxylate-alumoxane for the preparation of ceramic coatings on polymer substrates. Our proposed approach is attractive since proof of concept has been demonstrated under the NRA 96-LeRC-1 Technology for Advanced High Temperature Gas Turbine Engines, HITEMP Program. For example, carbon and Kevlar(tm) fibers and matting have been successfully coated with ceramic thermally protective layers.

  9. Factors optimization to improve the tensile and flexural properties of short fibre non-woven hedgehog chestnuts spines reinforced polyester composites

    OpenAIRE

    Ribeiro, J.E.; Rocha, João; Queijo, Luís

    2016-01-01

    Over the last decade has been observed an increased interest in the use of natural fibers instead of synthetic fibres (i.e. glass, carbon or kevlar fibres). The natural fibre composites (NFC) have important advantages like their fibers are a renewable resource, for which production requires little energy, involves CO2 absorption, whilst returning oxygen to the environment and can be produced at lower cost than synthetic fibre [1]. However, the NFC have also some limitations, na...

  10. 26 CFR 1.42-6 - Buildings qualifying for carryover allocations.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 1 2010-04-01 2010-04-01 true Buildings qualifying for carryover allocations. 1... INCOME TAXES Credits Against Tax § 1.42-6 Buildings qualifying for carryover allocations. (a) Carryover... carryover allocation may only be made with respect to a qualified building. A qualified building is any...

  11. Raman measurements of Kevlar-29 fiber pull-out test at different strain levels

    Science.gov (United States)

    Wang, Quan; Lei, Zhenkun; Kang, Yilan; Qiu, Wei

    2008-11-01

    This paper adopted Kevlar-29 fiber monofilament embedding technology to prepare fiber/ epoxy resin tensile specimen. The specimen was pulled on a homemade and portable mini-loading device. At the same time micro-Raman spectroscopy is introduced to detect the distributions of stress on the embedded fiber at different strain levels. The characteristic peak shift of the 1610 cm-1 in Raman band has a linear relationship with the strain or stress. The experimental results show that the fiber axial stress decreases gradually from the embedded fiber-start to the embedded fiber-end at the same strain level. At different strain levels, the fiber axial stress increases along with the applied load. It reveals that there is a larger fiber axial stress distribution under a larger strain level. And the stress transfer is realized gradually from the embedded fiber-start to the fiber-end. Stress concentration exists in the embedded fiber-end, which is a dangerous region for interfacial debonding easily.

  12. 26 CFR 1.43-4 - Qualified enhanced oil recovery costs.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 1 2010-04-01 2010-04-01 true Qualified enhanced oil recovery costs. 1.43-4... TAXES Credits Against Tax § 1.43-4 Qualified enhanced oil recovery costs. (a) Qualifying costs—(1) In... “qualified enhanced oil recovery costs” if the amounts are paid or incurred with respect to an asset which is...

  13. Evaluation of Thin Kevlar-Epoxy Fabric Panels Subjected to Shear Loading

    Science.gov (United States)

    Baker, Donald J.

    1996-01-01

    The results of an analytical and experimental investigation of 4-ply Kevlar-49-epoxy panels loaded by in-plane shear are presented. Approximately one-half of the panels are thin-core sandwich panels and the other panels are solid-laminate panels. Selected panels were impacted with an aluminum sphere at a velocity of either 150 or 220 ft/sec. The strength of panels impacted at 150 ft/sec was not reduced when compared to the strength of the undamaged panels, but the strength of panels impacted at 220 ft/sec was reduced by 27 to 40 percent. Results are presented for panels that were cyclically loaded from a load less than the buckling load to a load in the postbuckling load range. The thin-core sandwich panels had a lower fatigue life than the solid panels. The residual strength of the solid and sandwich panels cycled more than one million cycles exceeded the baseline undamaged panel strengths. The effect of hysteresis in the response of the sandwich panels is not significant. Results of a nonlinear finite element analysis conducted for each panel design are presented.

  14. Safety concerns in composite manufacturing and machining

    Science.gov (United States)

    Asmatulu, Eylem; Alonayni, Abdullah; Alamir, Mohammed

    2018-03-01

    Because of the superior properties, composites have been used in many industrial applications, including aerospace, wind turbines, ships, cars, fishing rods, storage tanks, swimming pool panels, and baseball bats. Each application may require different combinations of reinforcements and matrices, which make the manufacturing safety even more challenging while working on these substances. In this study, safety issues in composite manufacturing and machining were investigated in detail, and latest developments were provided for workers. The materials most frequently used in composite manufacturing, such as matrix (polyester, vinylester, phenolic, epoxies, methyl ethyl ketone peroxide, benzoil peroxide, hardeners, and solvents), and reinforcement materials (carbon, glass and Kevlar fibers, honeycomb and foams) can be highly toxic to human body. These materials can also be very toxic to the environment when dumped out uncontrollably, creating major future health and environmental concerns. Throughout the manufacturing process, workers inhale vapors of the liquid matrix, hardeners and solvents / thinners, as well as reinforcement materials (chopped fibers and particles) in airborne. Milling, cutting and machining of the composites can further increase the toxic inhalations of airborne composite particles, resulting in major rashes, irritation, skin disorders, coughing, severe eye and lung injury and other serious illnesses. The major portions of these hazardous materials can be controlled using appropriate personal protective equipment for the chemicals and materials used in composite manufacturing and machining. This study provides best possible safety practices utilized in composite manufacturing facilities for workers, engineers and other participants.

  15. 12 CFR 621.4 - Audit by qualified public accountant.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Audit by qualified public accountant. 621.4... REQUIREMENTS General Rules § 621.4 Audit by qualified public accountant. (a) Each institution shall, at least annually, have its financial statements audited by a qualified public accountant in accordance with...

  16. Tribo-performance evaluation of ecofriendly brake friction composite materials

    Science.gov (United States)

    Kumar, Naresh; Singh, Tej; Grewal, G. S.

    2018-05-01

    This paper presents the potential of natural fibre in brake friction materials. Natural fibre filled ecofriendly brake friction materials were developed without Kevlar fibre evaluated for tribo-performance on a chase friction testing machine following SAE J 661a standard. Experimental results indicated that natural fibre enhances the fade performance, but depresses the friction and wear performance, whereas Kevlar fibre improves the friction, wear and recovery performance but depresses the fade performance. Also the results revealed that with the increase in natural fibre content, the friction and fade performances enhanced.

  17. Low cost tooling material and process for graphite and Kevlar composites

    Science.gov (United States)

    Childs, William I.

    1987-01-01

    An Extruded Sheet Tooling Compound (ESTC) was developed for use in quickly building low cost molds for fabricating composites. The ESTC is a very highly mineral-filled resin system formed into a 6 mm thick sheet. The sheet is laid on the pattern, vacuum (bag) is applied to remove air from the pattern surface, and the assembly is heat cured. The formed ESTC is then backed and/or framed and ready for use. The cured ESTC exhibits low coefficient of thermal expansion and maintains strength at temperatures of 180 to 200 C. Tools were made and used successfully for: Compression molding of high strength epoxy sheet molding compound, stamping of aluminum, resin transfer molding of polyester, and liquid resin molding of polyester. Several variations of ESTC can be made for specific requirements. Higher thermal conductivity can be achieved by using an aluminum particle filler. Room temperature gel is possible to allow use of foam patterns.

  18. Aerogel Hybrid Composite Materials: Designs and Testing for Multifunctional Applications

    Science.gov (United States)

    Williams, Martha K.; Fesmire, James E.

    2016-01-01

    This webinar will introduce the broad spectrum of aerogel composites and their diverse performance properties such as reduced heat transfer to energy storage, and expands specifically on the aerogel/fiber laminate systems and testing methodologies. The multi-functional laminate composite system, AeroFiber, and its construction is designed by varying the type of fiber (e.g. polyester, carbon, Kevlar®, Spectra® or Innegral(TradeMark) and combinations thereof), the aerogel panel type and thickness, and overall layup configuration. The combination and design of materials may be customized and tailored to achieve a range of desired properties in the resulting laminate system. Multi-functional properties include structural strength, impact resistance, reduction in heat transfer, increased fire resistance, mechanical energy absorption, and acoustic energy dampening. Applications include aerospace, aircraft, automotive, boating, building and construction, lightweight portable structures, liquefied natural gas, cryogenics, transportation and energy, sporting equipment, and military protective gear industries.

  19. Mechanical behavior and fatigue in polymeric composites at low temperatures

    International Nuclear Information System (INIS)

    Katz, Y.; Bussiba, A.; Mathias, H.

    1986-01-01

    Advanced fiber reinforced polymeric composite materials are often suggested as structural materials at low temperature. In this study, graphite epoxy and Kevlar-49/epoxy systems were investigated. Fatigue behavior was emphasized after establishing the standard monotonic mechanical properties, including fracture resistance parameters at 77, 190, and 296 K. Tension-tension fatigue crack propagation testing was carried out at nominal constant stress intensity amplitudes using precracked compact tensile specimens. The crack tip damage zone was measured and tracked by an electro-potential device, opening displacement gage, microscopic observation, and acoustic emission activity recording. Fractograhic and metallographic studies were performed with emphasis on fracture morphology and modes, failure processes, and description of sequential events. On the basis of these experimental results, the problem of fatigue resistance, including low temperature effects, is analyzed and discussed. The fundamental concepts of fatigue in composites are assessed, particularly in terms of fracture mechanics methods

  20. 26 CFR 1.7704-3 - Qualifying income.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 13 2010-04-01 2010-04-01 false Qualifying income. 1.7704-3 Section 1.7704-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES General Actuarial Valuations § 1.7704-3 Qualifying income. (a) Certain investment income—(1...

  1. STUDY THE CREEP OF TUBULAR SHAPED FIBER REINFORCED COMPOSITES

    Directory of Open Access Journals (Sweden)

    Najat J. Saleh

    2013-05-01

    Full Text Available Inpresent work tubular –shaped fiber reinforced composites were manufactured byusing two types of resins ( Epoxy and unsaturated polyester and separatelyreinforced with glass, carbon and kevlar-49 fibers (filament and woven roving,hybrid reinforcement composites of these fibers were also prepared. The fiberswere wet wound on a mandrel using a purposely designed winding machine,developed by modifying an ordinary lathe, in winding angle of 55° for filament. A creep test was made of either the fulltube or specimens taken from it. Creep was found to increase upon reinforcementin accordance to the rule of mixture and mainly decided by the type of singleor hybridized fibers. The creep behavior, showed that the observed strain tendsto appear much faster at higher temperature as compared with that exhibited atroom temperate. The creep rate also found to be depending on fiber type, matrixtype, and the fiber /matrix bonding. The creep energy calculated fromexperimental observations was found to exhibit highest value for hybridizedreinforcement.

  2. Erosão em compósitos à base de fibras de vidro/kevlar e resina epóxi de uso aeronáutico Erosion on composite materials based on glass and kevlar fibers/epoxy resin used in the aeronautical industry

    Directory of Open Access Journals (Sweden)

    Rogério A. Silva

    2003-01-01

    Full Text Available Este trabalho tem como objetivo principal o estudo e a análise da eficiência de dois diferentes tipos de recobrimentos usados na proteção contra o processo de desgaste por erosão em substratos fabricados em materiais compósitos poliméricos de uso aeronáutico, dando ênfase às peças fabricadas em fibras de vidro / kevlar impregnadas com resina epóxi. Revestimentos protetores baseados em um determinado tipo de tinta de poliuretano e um filme incolor de poliuretano foram utilizados para a avaliação da resistência à erosão, quando submetidos ao jateamento com microesferas de vidro. Para a realização dos ensaios de erosão foi projetado e construído um dispositivo específico para esse fim. Nos ensaios alguns fatores foram considerados, tais como: a natureza física das partículas abrasivas de microesferas de vidro, a distância, a velocidade e o ângulo de ataque das partículas durante o processo de jateamento. Os corpos-de-prova foram analisados quanto à sua variação de massa. Foram, também, utilizadas técnicas metalográficas na preparação de corpos-de-prova que foram analisados por microscopias óptica e eletrônica de varredura, assistida pela técnica de EDS, caracterizando o processo de erosão. Os resultados mostraram que os corpos-de-prova de compósitos poliméricos revestidos somente com a tinta de poliuretano apresentaram baixa resistência no ensaio de erosão. Entretanto, esta tinta quando protegida pelo filme incolor de poliuretano teve sua resistência à erosão aumentada na ordem de 5 vezes, aumentando, conseqüentemente, a vida útil do componente aeronáutico em sua aplicação final. Devido à facilidade de aplicação do filme de poliuretano no componente a ser protegido, os resultados deste estudo já estão sendo utilizados pelos fabricantes de aeronaves e operadores.The main goal of the present work is to evaluate the efficiency of two different coatings used as protection against the erosion wear

  3. Accident data study of concrete construction companies' similarities and differences between qualified and non-qualified workers in Spain.

    Science.gov (United States)

    López-Arquillos, Antonio; Rubio-Romero, Juan Carlos; Gibb, Alistair

    2015-01-01

    The aim of this paper is to discuss findings from an analysis of accidents in concrete construction companies in Spain and to compare the accident rates of qualified and non-qualified workers. A total of 125,021 accidents between 2003 and 2008 involving both blue-collar and white-collar workers were analysed, comparing the variables of occupation, age, company staff, length of service, location of the accident, together with the severity of the accidents. Results showed that lack of experience in the first month is more significant in non-qualified workers and experienced supervisors and that head injuries are more likely to lead to fatalities. The most remarkable similarity was that fatal accidents to and from the worksite are a problem common to both groups of workers.

  4. 26 CFR 52.4682-2 - Qualifying sales.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 17 2010-04-01 2010-04-01 false Qualifying sales. 52.4682-2 Section 52.4682-2... TAXES (CONTINUED) ENVIRONMENTAL TAXES § 52.4682-2 Qualifying sales. (a) In general—(1) Special rules applicable to certain sales. Special rules apply to sales of ODCs in the following cases: (i) Under section...

  5. Hybrid Composite Material and Solid Particle Erosion Studies

    Science.gov (United States)

    Chellaganesh, D.; Khan, M. Adam; Ashif, A. Mohamed; Ragul Selvan, T.; Nachiappan, S.; Winowlin Jappes, J. T.

    2018-04-01

    Composite is one of the predominant material for most challenging engineering components. Most of the components are in the place of automobile structure, aircraft structures, and wind turbine blade and so on. At the same all the components are indulged to mechanical loading. Recent research on composite material are machinability, wear, tear and corrosion studies. One of the major issue on recent research was solid particle air jet erosion. In this paper hybrid composite material with and without filler. The fibre are in the combination of hemp – kevlar (60:40 wt.%) as reinforcement using epoxy as a matrix. The natural material palm and coconut shell are used as filler materials in the form of crushed powder. The process parameter involved are air jet velocity, volume of erodent and angle of impingement. Experiment performed are in eight different combinations followed from 2k (k = 3) factorial design. From the investigation surface morphology was studied using electron microscope. Mass change with respect to time are used to calculate wear rate and the influence of the process parameters. While solid particle erosion the hard particle impregnates in soft matrix material. Influence of filler material has reduced the wear and compared to plain natural composite material.

  6. Time-Dependent Behavior of High-Strength Kevlar and Vectran Webbing

    Science.gov (United States)

    Jones, Thomas C.; Doggett, William R.

    2014-01-01

    High-strength Kevlar and Vectran webbings are currently being used by both NASA and industry as the primary load-bearing structure in inflatable space habitation modules. The time-dependent behavior of high-strength webbing architectures is a vital area of research that is providing critical material data to guide a more robust design process for this class of structures. This paper details the results of a series of time-dependent tests on 1-inch wide webbing including an initial set of comparative tests between specimens that underwent realtime and accelerated creep at 65 and 70% of their ultimate tensile strength. Variability in the ultimate tensile strength of the webbings is investigated and compared with variability in the creep life response. Additional testing studied the effects of load and displacement rate, specimen length and the time-dependent effects of preconditioning the webbings. The creep test facilities, instrumentation and test procedures are also detailed. The accelerated creep tests display consistently longer times to failure than their real-time counterparts; however, several factors were identified that may contribute to the observed disparity. Test setup and instrumentation, grip type, loading scheme, thermal environment and accelerated test postprocessing along with material variability are among these factors. Their effects are discussed and future work is detailed for the exploration and elimination of some of these factors in order to achieve a higher fidelity comparison.

  7. Shape memory alloy wires turn composites into smart structures: I. Material requirements

    Science.gov (United States)

    Schrooten, Jan; Michaud, Veronique J.; Zheng, Yanjun; Balta-Neumann, J. Antonio; Manson, Jan-Anders E.

    2002-07-01

    Composites containing thin Shape Memory Alloy (SMA) wires show great potential as materials able to adapt their shape, thermal behavior or vibrational properties to external stimuli. The functional properties of SMA-composites are directly related to the constraining effect of the matrix on the reversible martensitic transformation of the embedded pre-strained SMA wires. The present work reports results of a concerted European effort towards a fundamental understanding of the manufacturing and design of SMA composites. This first part investigates the transformational behavior of constrained SMA wires and its translation into functional properties of SMA composites. Thermodynamic and thermomechanical experiments were performed on SMA wires. A model was developed to simulate the thermomechanical behavior of the wires. From the screening of potential wires it was concluded that NiTiCu, as well as R-phase NiTi appeared as best candidates. Requirements for the host composite materials were surveyed. A Kevlar-epoxy system was chosen. Finally, the quality of the SMA wire-resin interface was assessed by two different techniques. These indicated that a thin oxide layer seems to provide the best interfacial strength. A temperature window in which SMA composites can be safely used was also defined. The manufacturing and properties of the SMA composites will be discussed in Part II.

  8. 6 CFR 25.4 - Designation of qualified anti-terrorism technologies.

    Science.gov (United States)

    2010-01-01

    ... 6 Domestic Security 1 2010-01-01 2010-01-01 false Designation of qualified anti-terrorism... REGULATIONS TO SUPPORT ANTI-TERRORISM BY FOSTERING EFFECTIVE TECHNOLOGIES § 25.4 Designation of qualified anti-terrorism technologies. (a) General. The Under Secretary may Designate as a Qualified Anti-Terrorism...

  9. High-Strength Hybrid Textile Composites with Carbon, Kevlar, and E-Glass Fibers for Impact-Resistant Structures. A Review.

    Science.gov (United States)

    Priyanka, P.; Dixit, A.; Mali, H. S.

    2017-11-01

    The paper reviews the characterization of high-performance hybrid textile composites and their hybridization effects of composite's behavior. Considered are research works based on the finite-element modeling, simulation, and experimental characterization of various mechanical properties of such composites.

  10. 12 CFR 619.9270 - Qualified Public Accountant or External Auditor.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Qualified Public Accountant or External Auditor... § 619.9270 Qualified Public Accountant or External Auditor. A qualified public accountant or external... constituted State authority, identifying such person as a certified public accountant; (b) Is licensed to...

  11. THz QCL-based active imaging dedicated to non-destructive testing of composite materials used in aeronautics

    Science.gov (United States)

    Destic, F.; Petitjean, Y.; Massenot, S.; Mollier, J.-C.; Barbieri, S.

    2010-08-01

    This paper presents a CW raster-scanning THz imaging setup, used to perform Non-Destructive Testing of KevlarTMand carbon fibre samples. The setup uses a 2.5 THz Quantum Cascade Laser as a source. Delamination defect in a Kevlar sample was detected showing a sensitivity to laser polarization orientation. Detection of a break in a carbon/epoxy sample was also performed.

  12. THz QCL-based active imaging dedicated to non-destructive testing of composite materials used in aeronautics

    OpenAIRE

    Destic, Fabien; Petitjean, Yoann; Massenot, Sébastien; Mollier, Jean-Claude; Barbieri, Stefano

    2010-01-01

    This paper presents a CW raster-scanning THz imaging setup, used to perform Non-Destructive Testing of KevlarTMand carbon fibre samples. The setup uses a 2.5 THz Quantum Cascade Laser as a source. Delamination defect in a Kevlar sample was detected showing a sensitivity to laser polarization orientation. Detection of a break in a carbon/epoxy sample was also performed.

  13. High temperature testing of TRUPACT-I materials: Kevlar, honeycomb, rigid polyurethane foam

    International Nuclear Information System (INIS)

    Hudson, M.L.

    1985-12-01

    When the Transuranic Package Transporter Model-I (TRUPACT-I) failed to afford sufficient containment after a 35-minute JP-4 fueled open-pool fire, component tests were conducted, in conjunction with analyses, to guide and assess the redesign of TRUPACT-I. Since materials which change phase or combust are difficult to numerically analyze, the component tests determined the behavior of these materials in TRUPACT-I. The component tests approximated the behavior of Kevlar (registered trademark of DuPont), metal honeycomb, and rigid polyurethane foam, as they appear in TRUPACT-I, in an open-pool fire environment. Six series of tests were performed at Sandia's Radiant Heat Facility and one test at the wind-shielded fire test facility (LAARC Chimney). Each test facility was controlled to yield temperatures or heat fluxes equivalent to those measured in the TRUPACT-I, Unit 0, open-pool fire. This extensive series of component tests (34 runs total) provided information on the high-temperature behavior of unique materials which was not previously available or otherwise attainable. The component tests were a timely and cost-effective means of providing the data for the TRUPACT-I redesign

  14. Isolation of aramid nanofibers for high strength multiscale fiber reinforced composites

    Science.gov (United States)

    Lin, Jiajun; Patterson, Brendan A.; Malakooti, Mohammad H.; Sodano, Henry A.

    2018-03-01

    Aramid fibers are famous for their high specific strength and energy absorption properties and have been intensively used for soft body armor and ballistic protection. However, the use of aramid fiber reinforced composites is barely observed in structural applications. Aramid fibers have smooth and inert surfaces that are unable to form robust adhesion to polymeric matrices due to their high crystallinity. Here, a novel method to effectively integrate aramid fibers into composites is developed through utilization of aramid nanofibers. Aramid nanofibers are prepared from macroscale aramid fibers (such as Kevlar®) and isolated through a simple and scalable dissolution method. Prepared aramid nanofibers are dispersible in many polymers due to their improved surface reactivity, meanwhile preserve the conjugated structure and likely the strength of their macroscale counterparts. Simultaneously improved elastic modulus, strength and fracture toughness are observed in aramid nanofiber reinforced epoxy nanocomposites. When integrated in continuous fiber reinforced composites, aramid nanofibers can also enhance interfacial properties by forming hydrogen bonds and π-π coordination to bridge matrix and macroscale fibers. Such multiscale reinforcement by aramid nanofibers and continuous fibers results in strong polymeric composites with robust mechanical properties that are necessary and long desired for structural applications.

  15. 47 CFR 59.4 - Definition of “qualifying carrier”.

    Science.gov (United States)

    2010-10-01

    ... (CONTINUED) INFRASTRUCTURE SHARING § 59.4 Definition of “qualifying carrier”. For purposes of this part, the term “qualifying carrier” means a telecommunications carrier that: (a) Lacks economies of scale or...

  16. Damage detection in laminar thermoplastic composite materials by means of embedded optical fibers

    Directory of Open Access Journals (Sweden)

    Kojović Aleksandar M.

    2006-01-01

    Full Text Available This paper investigates the possibility of applying optical fibers as sensors for investigating low energy impact damage in laminar thermoplastic composite materials, in real time. Impact toughness testing by a Charpy impact pendulum with different loads was conducted in order to determine the method for comparative measurement of the resulting damage in the material. For that purpose intensity-based optical fibers were built in to specimens of composite materials with Kevlar 129 (the DuPont registered trade-mark for poly(p-phenylene terephthalamide woven fabric as reinforcement and thermoplastic PVB (poly(vinyl butyral as the matrix. In some specimens part of the layers of Kevlar was replaced with metal mesh (50% or 33% of the layers. Experimental testing was conducted in order to observe and analyze the response of the material under multiple low-energy impacts. Light from the light-emitting diode (LED was launched to the embedded optical fiber and was propagated to the phototransistor-based photo detector. During each impact, the signal level, which is proportional to the light intensity in the optical fiber, drops and then slowly recovers. The obtained signals were analyzed to determine the appropriate method for real time damage monitoring. The major part of the damage occurs during impact. The damage reflects as a local, temporary release of strain in the optical fiber and an increase of the signal level. The obtained results show that intensity-based optical fibers could be used for measuring the damage in laminar thermoplastic composite materials. The acquired optical fiber signals depend on the type of material, but the same set of rules (relatively different, depending on the type of material could be specified. Using real time measurement of the signal during impact and appropriate analysis enables quantitative evaluation of the impact damage in the material. Existing methods in most cases use just the intensity of the signal before

  17. Studies on Poly(propylene fumarate-co-caprolactone diol Thermoset Composites towards the Development of Biodegradable Bone Fixation Devices

    Directory of Open Access Journals (Sweden)

    M. Jayabalan

    2009-01-01

    Full Text Available The effect of reinforcement in the cross-linked poly(propylene fumarate-co-caprolactone diol thermoset composites based on Kevlar fibres and hydroxyapatite was studied. Cross-linked poly(propylene fumarate-co-caprolactone diol was also studied without any reinforcement for comparison. The reinforcing fibre acts as a barrier for the curing reaction leading to longer setting time and lesser cross-link density. The fibre and HA reinforced composites have almost the same compressive strength. Nonreinforced material undergoes greater degree of swelling. Among the reinforced materials, the hydroxyapatite reinforced composite has a much higher swelling percentage than the fibre reinforced one. The studies on in vitro degradation of the cured materials reveal hydrolytic degradation in Ringer's solution and PBS medium during aging. All the three materials are found to swell initially in Ringer's solution and PBS medium during aging and then undergo gradual degradation. Compression properties of these cross-linked composites increase with aging; HA reinforced composite has the highest compressive strength and compressive modulus, whereas the aged fibre-reinforced composite has the least compressive strength and modulus.

  18. Studies on Poly(propylene fumarate-co-caprolactone diol) Thermoset Composites towards the Development of Biodegradable Bone Fixation Devices.

    Science.gov (United States)

    Jayabalan, M

    2009-01-01

    The effect of reinforcement in the cross-linked poly(propylene fumarate-co-caprolactone diol) thermoset composites based on Kevlar fibres and hydroxyapatite was studied. Cross-linked poly(propylene fumarate-co-caprolactone diol) was also studied without any reinforcement for comparison. The reinforcing fibre acts as a barrier for the curing reaction leading to longer setting time and lesser cross-link density. The fibre and HA reinforced composites have almost the same compressive strength. Nonreinforced material undergoes greater degree of swelling. Among the reinforced materials, the hydroxyapatite reinforced composite has a much higher swelling percentage than the fibre reinforced one. The studies on in vitro degradation of the cured materials reveal hydrolytic degradation in Ringer's solution and PBS medium during aging. All the three materials are found to swell initially in Ringer's solution and PBS medium during aging and then undergo gradual degradation. Compression properties of these cross-linked composites increase with aging; HA reinforced composite has the highest compressive strength and compressive modulus, whereas the aged fibre-reinforced composite has the least compressive strength and modulus.

  19. The technical qualified expert on radiation protection in Spain

    International Nuclear Information System (INIS)

    Marco Arboli, M.; Rodriguez Suarez, M.

    2002-01-01

    Education and training is considered an important tool for promoting safety culture and improving the level of competence of workers. In the different disciplines involved in Radiation Protection (PR), training programmes are being revised to ensure effective protection of individuals. In the European Union framework, the new normative and its adaptation in the Member States, as well as the past actions in each country, make the community to conclude that harmonization of educational programmes and European recognition of the qualification must be reached. An important point of these actions is the definition of the European Qualified Expert. Article 38 of the EURATOM Basic Safety Standards imposes requirements on training and education of the qualified experts and their exchange within the European Union. Since then, there has been many initiatives to seek to harmonization of the qualified expert requirements. In the Spanish education system, there has been a standard training and competent authority recognition of the high level qualified experts on radiation protection since 1986, whose programme is continuously being updating and improving. Taking into account the European actions to define the qualified expert training requirements, it has been designed an educational course for the Technical Qualified Expert on Radiation Protection. This pilot course has being carried out during May, 2002. The results of this project is shown in this paper. (Author)

  20. 26 CFR 1.860F-1 - Qualified liquidations.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Qualified liquidations. 1.860F-1 Section 1.860F-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment Trusts § 1.860F-1 Qualified liquidations. A plan of...

  1. 49 CFR 604.7 - Qualified human service organizations.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Qualified human service organizations. 604.7... organizations. (a) A recipient may provide charter service to a qualified human service organization (QHSO) for... disabilities; or (3) With low income. (b) If an organization serving persons described in paragraph (a) of this...

  2. 26 CFR 25.2701-4 - Accumulated qualified payments.

    Science.gov (United States)

    2010-04-01

    ... compound interest from the due date of the payment at a rate not less than the appropriate discount rate is... retained interest conferring a distribution right that was previously valued as a qualified payment right (a “qualified payment interest”), the taxable estate or taxable gifts of the individual holding the...

  3. Lightweight, Composite Cryogenic Tank Structures, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Microcosm has developed and qualified strong, all-composite LOX tanks for launch vehicles. Our new 42-inch diameter tank design weighs 486 lbs and burst without...

  4. 26 CFR 48.4041-19 - Exemption for qualified methanol and ethanol fuel.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Exemption for qualified methanol and ethanol....4041-19 Exemption for qualified methanol and ethanol fuel. (a) In general. Under section 4041(b)(2... or use of qualified methanol or ethanol fuel. (b) Qualified methanol or ethanol fuel defined. For...

  5. Modern filaments for composite materials

    International Nuclear Information System (INIS)

    Krivelli-Viskonti, I.

    1982-01-01

    Analysis of modern state and ways to improve properties of different filaments for the forecast of the filament application in composite materials has been conducted. In the near future as before the greatest attention will be paid to fibre glass, as this material is widely used in the reinforcing of organic matrices. Carbon and kevlar filaments are the most prospective ones. For the service at medium, high or superhigh temperatures selection of matrix material is more significant than selection of filament. Organic matrices can not be used at temperatures > 250 deg C: this is already the range of metal matrix application. Though at temperatures above room one many filaments can be used, boron filaments and metal wire are the only reinforcing materials, inspite of the fact that carbon filaments are successfully used for metal matrix reinforcing. At very high temperatures only carbon filaments or silicon carbide ones can be used, but their cost is very high and besides economical problems there are many difficulties of technical character

  6. Effect and origin of the structure of hyperbranched polysiloxane on the surface and integrated performances of grafted Kevlar fibers

    International Nuclear Information System (INIS)

    Zhang, Hongrui; Yuan, Li; Liang, Guozheng; Gu, Aijuan

    2014-01-01

    Highlights: • Four new hyperbranched polysiloxanes (HPSis) with various structures were prepared. • HPSis have different molecular weights and contents of active groups. • Four grafted Kevlar fibers (HPSi-g-KFs) were facilely prepared with different HPSis. • The structure and properties of HPSi-g-KF depend on the structure of HPSi. • The origin behind greatly improved integrated properties of HPSi-g-KF is discussed. - Abstract: Four hyperbranched polysiloxanes (HPSis) with different molecular weights and concentration ratios of double bonds to epoxy groups (1:6.5–1:0.7) were synthesized and characterized. Each HPSi was facilely grafted onto surfaces of Kevlar fibers (KFs) to develop novel modified fibers (HPSi-g-KFs). The structures and integrated properties of HPSi-g-KFs as well as the origin behind were systematically investigated. Results show that HPSi-g-KFs have much rougher surface morphologies, and their surface free energies are as high as about 1.7 times that of KFs, showing greatly improved wettability. Besides, HPSi-g-KFs have excellent UV resistance after 168 h UV irradiation, the retentions of tenacity, energy to break, modulus and break extension are as high as 92, 86, 95 and 96%, respectively, while those of KFs are 66–85%. In addition, compared with KFs, HPSi-g-KFs have higher tensile tenacity and energy to break with similar modulus and break extension, much better thermal stability and flame retardancy. The nature of HPSi has different influence on different property of fibers, the HPSi with smaller molecular weight and more epoxy groups is beneficial to prepare HPSi-g-KFs with better wettability, while that with larger molecular weight and more double bonds tends to prepare HPSi-g-KF with better flame retardancy and UV resistance

  7. Synthesis, processing and characterization of shear thickening fluid (STF) impregnated fabric composites

    International Nuclear Information System (INIS)

    Hassan, Tarig A.; Rangari, Vijay K.; Jeelani, Shaik

    2010-01-01

    Shear thickening is a non-Newtonian fluid behavior defined as the increase of viscosity with the increase in the applied shear rate. The shear thickening fluid (STF) is a combination of hard metal oxide particles suspended in a liquid polymer. This mixture of flowable and hard components at a particular composition, results in a material with remarkable properties. In this manuscript the shear thickening fluid (STF) was prepared by ultrasound irradiation of silica nanoparticles dispersed in liquid polyethylene glycol polymer. The as-prepared STFs have been tested for their rheological and thermal properties. Kevlar and Nylon fabrics were soaked in STF/ethanol solution to make STF/fabric composite. Knife threats and quasistatic penetration tests were performed on the neat fabrics and STF/fabric composite targets for both engineered spike and knife on areal density basis. The results showed that STF impregnated fabrics have better penetration resistance as compared to neat fabrics without affecting the fabric flexibility. This indicates that the addition of STF to the fabric have enhanced the fabric performance and can be used in liquid body armor applications.

  8. Qualified Health Plan (QHP) Landscape

    Data.gov (United States)

    U.S. Department of Health & Human Services — QHP Landscape Files present basic information about certified Qualified Health Plans and Stand-alone Dental Plans for individuals-families and small businesses...

  9. Aging techniques and qualified life for safety system components

    International Nuclear Information System (INIS)

    Weaver, W.W.

    1980-01-01

    Presently, the qualified life objective for Class IE safety system components in nuclear power plants is somewhat of a subjective engineering judgment. When the desired qualified life is ascertained, there are other choices that must be made (which may be influenced by the desired qualified life) such as selecting the aging procedure to use in the qualification process. Adding complexity to the situation is the fact that there are some limitations in aging techniques at the present time. This article presents (1) a discussion of the limitations in aging procedures, (2) the general philosophy of qualification, and (3) a proposed method for specifying a desired qualified life, which uses a probabilistic approach. The probabilistic approach proposed in item 3 can be applied to natural aging programs and eventually to accelerated aging once the present technical difficulties are overcome

  10. The Netherlands: Quality of work and employment of low-qualified workers

    NARCIS (Netherlands)

    Gouw, P.

    2013-01-01

    Based on the Netherlands Working Condition Survey (NEA, TNO) and the available literature, it seems that low-qualified workers experience more labour market problems than middle- or high-qualified workers. The trend in the 2000-2007 period is that the relative number of low qualified workers has

  11. Strength and dynamic characteristics analyses of wound composite axial impeller

    Science.gov (United States)

    Wang, Jifeng; Olortegui-Yume, Jorge; Müller, Norbert

    2012-03-01

    A low cost, light weight, high performance composite material turbomachinery impeller with a uniquely designed blade patterns is analyzed. Such impellers can economically enable refrigeration plants to use water as a refrigerant (R718). A strength and dynamic characteristics analyses procedure is developed to assess the maximum stresses and natural frequencies of these wound composite axial impellers under operating loading conditions. Numerical simulation using FEM for two-dimensional and three-dimensional impellers was investigated. A commercially available software ANSYS is used for the finite element calculations. Analysis is done for different blade geometries and then suggestions are made for optimum design parameters. In order to avoid operating at resonance, which can make impellers suffer a significant reduction in the design life, the designer must calculate the natural frequency and modal shape of the impeller to analyze the dynamic characteristics. The results show that using composite Kevlar fiber/epoxy matrix enables the impeller to run at high tip speed and withstand the stresses, no critical speed will be matched during start-up and shut-down, and that mass imbalances of the impeller shall not pose a critical problem.

  12. On the Mechanical Behavior of Advanced Composite Material Structures

    Science.gov (United States)

    Vinson, Jack

    During the period between 1993 and 2004, the author, as well as some colleagues and graduate students, had the honor to be supported by the Office of Naval Research to conduct research in several aspects of the behavior of structures composed of composite materials. The topics involved in this research program were numerous, but all contributed to increasing the understanding of how various structures that are useful for marine applications behaved. More specifically, the research topics focused on the reaction of structures that were made of fiber reinforced polymer matrix composites when subjected to various loads and environmental conditions. This included the behavior of beam, plate/panel and shell structures. It involved studies that are applicable to fiberglass, graphite/carbon and Kevlar fibers imbedded in epoxy, polyester and other polymeric matrices. Unidirectional, cross-ply, angle ply, and woven composites were involved, both in laminated, monocoque as well as in sandwich constructions. Mid-plane symmetric as well as asymmetric laminates were studied, the latter involving bending-stretching coupling and other couplings that only can be achieved with advanced composite materials. The composite structures studied involved static loads, dynamic loading, shock loading as well as thermal and hygrothermal environments. One major consideration was determining the mechanical properties of composite materials subjected to high strain rates because the mechanical properties vary so significantly as the strain rate increases. A considerable number of references are cited for further reading and study for those interested.

  13. The UK system of recognising qualified experts

    International Nuclear Information System (INIS)

    Bines, W.

    2002-01-01

    EURATOM Basic Safety Standards (BSS) Directives have long included requirements for the involvement of qualified experts, the definition of which has scarcely changed since at least 1976. The Directive requirement, in the definition of qualified expert,, for competent authorities to recognise the capacity to act as a qualified expert has been interpreted by Member States in widely differing ways, ranging from the minimalist or case by case to the highly detailed and prescriptive. In the United Kingdom (UK), the qualified expert for occupational radiation protection is the radiation protection adviser and the competent authority is the Health and Safety Executive (HSE). The Ionising Radiations Regulations 1985, which largely implemented the 1980 BSS Directive, required an employer to appoint one or more radiation protection advisers for the purpose of advising him as to the observance of these Regulations and other health and safety matters in connection with ionising radiation. The Regulations addressed the question of recognition by forbidding an employer to appoint a person as a radiation protection adviser unless: that person was suitably qualified and experienced; the employer had notified the Health and Safety Executive in writing of the intended appointment at least 28 days in advance, giving the name of the person and particulars of his qualifications and experience and the scope of the advice he would be required to give; and the employer had received from HSE an acknowledgement in writing of the notification. This system allowed HSE to follow up and query any apparently unsuitable potential appointments while applying a light overall administrative touch. The Approved Code of Practice supporting the Regulations included advice on the qualifications, experience and qualities that the employer should look for in a suitable radiation protection adviser

  14. 30 CFR 203.43 - To which production do I apply the RSV earned from qualified deep wells or qualified phase 1...

    Science.gov (United States)

    2010-07-01

    ... in water between 200 and 400 meters deep, you begin drilling an original deep well with a perforated... 200 meters deep; (ii) May 18, 2007, for an RSV earned by a qualified deep well on a lease that is located entirely in water more than 200 meters deep; or (iii) The date that the first qualified well that...

  15. 10 CFR 451.4 - What is a qualified renewable energy facility.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false What is a qualified renewable energy facility. 451.4 Section 451.4 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION RENEWABLE ENERGY PRODUCTION INCENTIVES § 451.4 What is a qualified renewable energy facility. In order to qualify for an incentive payment under...

  16. Free Vibrations of Uniform Pipes Made From Composite Materials at an Internal Flow Under Effect of Additional Boundary Conditions

    Directory of Open Access Journals (Sweden)

    Nawal H. Al – Raheimy

    2016-09-01

    Full Text Available In this paper the approximate method of Raleigh method can be used to study the effect of additional boundary conditions (clamped – free & clamped – clamped on the free transverse vibrations of uniform pipes which have length, L (1m , inner radius, "Ri" (1cm & thickness, "t" (1mm made from composite materials, where the resin of unsaturated polyester represented the matrix material reinforced by aligned (E-fibers glass in the first case and used aligned fiber (Kevlar-49 in the second case. The length of fibers is in the two types, the first type is long fibers (continuous and the second is short fibers (discontinuous for different length all at volume fraction of fibers, "f" (0.15 & 0.25. At any construction of the pipe in composite material the natural frequency decreased when the velocity of flow increased from zero to critical velocity also can be observed the pipe at clamped – clamped boundary conditions predicts natural frequency & critical velocity greater than that pipe at clamped – free. The natural frequency and critical velocity increase with increasing volume fraction and length of discontinuous fiber. The value of natural frequency for pipes which have continuous fibers is constant at certain velocity of flow while are variable in pipes which have discontinuous fibers according to ratio between length of short fiber to critical length of discontinuous fiber whereas the natural frequency increase with increasing this ratio. Finally the pipes with Kevlar fiber have high critical velocity and natural frequency compare with pipes for fiber glass.

  17. Tensile strength changeability of multilayered composites, fabricated through optimized VARTM Technology, an experimental

    International Nuclear Information System (INIS)

    Nasir, M.A.; Khan, Z.M.

    2016-01-01

    Life span estimation up to tensile fracture of different fiber reinforced composites, Kevlar Fiber Reinforced Polymer (KFRP) and Glass Fiber Reinforced Polymer (GFRP) along with the strain rate effects on dynamic properties is mainly viewed on experimental basis in this paper. Lab-scale Vacuum Assisted Resin Transfer Molding (VARTM) technique is used to fabricate flawless dog bone specimens considering ASTM standard D638-03 and by using LY5052 resin and HY 5052 hardener. In this research, it is tried to maintain 65% of fiber participation in whole specimen composition matrix. Detail design description of VARTM is also discussed and optimized up to maximum scale to acquire compact, uniformly strengthen and porosity banned standard specimens. A conventional stress-strain curve is established to compare the tensile validity of above mentioned competitive composites. Crack Opening Displacement (COD) of research materials after equal intervals of time is observed; results depict the shear stability and reinforcement perfection of these materials. The crack penetration behavior is examined transversely and longitudinally in this research. (author)

  18. Nutrient Composition of Retail Samples of Australian Beef Sausages

    Directory of Open Access Journals (Sweden)

    Judy Cunningham

    2015-11-01

    Full Text Available Some nutrient data for beef sausages in Australia’s food composition table, NUTTAB 2010, is over 25 years old and may no longer reflect the composition of this popular food. To update this, 41 retail samples of fresh beef sausages were purchased in Melbourne, Australia, in May 2015. Each purchase was analysed, uncooked, for moisture, protein and fat. Sausages were then grouped by fat content into one of three composites and analysed for a wide range of nutrients, before and after dry heat cooking, the most popular sausage cooking method. Fat content in raw sausages averaged 14.9 g/100 g, 30% lower than NUTTAB values, varying from 7.3 to 22.6 g/100 g. This indicates it is possible to formulate leaner sausages that meet consumer expectations and may qualify for certain nutrition labelling statements. Under current Australian labelling requirements, two low fat sausages contain sufficient protein, B12, niacin, phosphorus and zinc to qualify as a good source of these nutrients and sufficient iron, selenium and vitamin A to qualify as a source of these. Sodium levels are higher than fresh beef, ranging from 680 to 840 mg/100 g. These data will be used to update NUTTAB and support product labelling and consumer education.

  19. Confidence in leadership among the newly qualified.

    Science.gov (United States)

    Bayliss-Pratt, Lisa; Morley, Mary; Bagley, Liz; Alderson, Steven

    2013-10-23

    The Francis report highlighted the importance of strong leadership from health professionals but it is unclear how prepared those who are newly qualified feel to take on a leadership role. We aimed to assess the confidence of newly qualified health professionals working in the West Midlands in the different competencies of the NHS Leadership Framework. Most respondents felt confident in their abilities to demonstrate personal qualities and work with others, but less so at managing or improving services or setting direction.

  20. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining procedure...

  1. Solar array qualification through qualified analysis

    Science.gov (United States)

    Zijdemans, J.; Cruijssen, H. J.; Wijker, J. J.

    1991-04-01

    To achieve qualification is in general a very expensive exercise. For solar arrays this is done by a dedicated test program through which final qualification is achieved. Due to severe competition on the solar array market, cheaper means are looked for to achieve a qualified product for the customers. One of the methods is to drastically limit the environmental test program and to qualify the solar-array structure against its environmental loads by analysis. Qualification by analysis is possible. The benefits are that a significant amount of development effort can be saved in case such a powerful tool is available. Extensive testing can be avoided thus saving time and money.

  2. Development of Ultra-Light Composite Material to Build the Platform of a Shaking Table

    Directory of Open Access Journals (Sweden)

    Botero-Jaramillo Eduardo

    2013-10-01

    Full Text Available Based on the developments of the last decades in the area of ultra-light materials, their application in the construction of the platform of the new one direction hydrau- lic shaking table was proposed, with capacity of one ton and frequency range from 0.4 Hz to 4.0 Hz for the Geotechnical Laboratory of the Institute of Engineering, UNAM. The aim was to replace the heavy conventional steel platforms, used in shaking tables, by a composite material based on wood and Kevlar, hence reducing its weight and optimizing the hydraulic equipment capacity available in the labora- tory. Accordingly, an experimental investigation was conducted to characterize the stress-strain behavior of composite materials under monotonically increasing load. This research involved the determination of the adequate proportions of the different constituent materials and manufacturing techniques that best suit the needs and available resources.

  3. 20 CFR 404.1018b - Medicare qualified government employment.

    Science.gov (United States)

    2010-04-01

    ... AND DISABILITY INSURANCE (1950- ) Employment, Wages, Self-Employment, and Self-Employment Income Work Excluded from Employment § 404.1018b Medicare qualified government employment. (a) General. The work of a... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Medicare qualified government employment. 404...

  4. Low-Income Housing Tax Credit (LIHTC) Qualified Census Tract (QCT)

    Data.gov (United States)

    Department of Housing and Urban Development — It allows to generate tables for Low-Income Housing Tax Credit (LIHTC) Qualified Census Tracts (QCT) and for Difficult Development Areas (DDA). LIHTC Qualified...

  5. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the procedure...

  6. 17 CFR 210.12-09 - Valuation and qualifying accounts.

    Science.gov (United States)

    2010-04-01

    ... period Column C—Additions (1)—Charged to costs and expenses (2)—Charged to other accounts—describe Column... qualifying accounts and reserves by descriptive title. Group (a) those valuation and qualifying accounts... accounts. 210.12-09 Section 210.12-09 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION...

  7. Fabrication, polarization, and characterization of PVDF matrix composites for integrated structural load sensing

    International Nuclear Information System (INIS)

    Haghiashtiani, Ghazaleh; Greminger, Michael A

    2015-01-01

    The focus of this work is to evaluate a new carbon fiber reinforced composite structure with integrated sensing capabilities. In this composite structure, the typical matrix material used for carbon fiber reinforced composites is replaced with the thermoplastic polyvinylidene difluoride (PVDF). Since PVDF has piezoelectric properties, it enables the structure to be used for integrated load sensing. In addition, the electrical conductivity property of the carbon fabric is harnessed to form the electrodes of the integrated sensor. In order to prevent the carbon fiber electrodes from shorting to each other, a thin Kevlar fabric layer is placed between the two carbon fiber electrode layers as a dielectric. The optimal polarization parameters were determined using a design of experiments approach. Once polarized, the samples were then used in compression and tensile tests to determine the effective d 33 and d 31 piezoelectric coefficients. The degree of polarization of the PVDF material was determined by relating the effective d 33 coefficient of the composite to the achieved d 33 of the PVDF component of the composite using a closed form expression. Using this approach, it was shown that optimal polarization of the composite material results in a PVDF component d 33 of 3.2 pC N −1 . Moreover, the Young’s modulus of the composite structure has been characterized. (paper)

  8. A Wear Geometry Model of Plain Woven Fabric Composites

    Directory of Open Access Journals (Sweden)

    Gu Dapeng

    2014-09-01

    Full Text Available The paper g describes a model meant for analysis of the wear geometry of plain woven fabric composites. The referred model consists of a mathematical description of plain woven fabric based on Peirce’s model coupled with a stratified method for the solution of the wear geometry. The evolutions of the wear area ratio of weft yarn, warp yarn and matrix resin on the worn surface are simulated by MatLab software in combination of warp and weft yarn diameters, warp and weft yarn-to-yarn distances, fabric structure phases (SPs. By comparing theoretical and experimental results from the PTFE/Kevlar fabric wear experiment, it can be concluded that the model can present a trend of the component area ratio variations along with the thickness of fabric, but has a inherently large error in quantitative analysis as an idealized model.

  9. 46 CFR 391.6 - Tax treatment of qualified withdrawals.

    Science.gov (United States)

    2010-10-01

    ... accounting whereby (1) payments shall reduce the basis of the property on the day such payments are actually... 46 Shipping 8 2010-10-01 2010-10-01 false Tax treatment of qualified withdrawals. 391.6 Section...-469 FEDERAL INCOME TAX ASPECTS OF THE CAPITAL CONSTRUCTION FUND § 391.6 Tax treatment of qualified...

  10. [Composition of chicken and quail eggs].

    Science.gov (United States)

    Closa, S J; Marchesich, C; Cabrera, M; Morales, J C

    1999-06-01

    Qualified food composition data on lipids composition are needed to evaluate intakes as a risk factor in the development of heart disease. Proximal composition, cholesterol and fatty acid content of chicken and quail eggs, usually consumed or traded, were analysed. Proximal composition were determined using AOAC (1984) specific techniques; lipids were extracted by a Folch's modified technique and cholesterol and fatty acids were determined by gas chromatography. Results corroborate the stability of eggs composition. Cholesterol content of quail eggs is similar to chicken eggs, but it is almost the half content of data registered in Handbook 8. Differences may be attributed to the analytical methodology used to obtain them. This study provides data obtained with up-date analytical techniques and accessory information useful for food composition tables.

  11. 42 CFR 436.128 - Coverage for certain qualified aliens.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Coverage for certain qualified aliens. 436.128... Mandatory Coverage of the Categorically Needy § 436.128 Coverage for certain qualified aliens. The agency... § 440.255(c) of this chapter to those aliens described in § 436.406(c) of this subpart. [55 FR 36820...

  12. 26 CFR 1.1092(c)-1 - Qualified covered calls.

    Science.gov (United States)

    2010-04-01

    ... lowest qualified benchmark is determined using the adjusted applicable stock price, as defined in § 1... (CONTINUED) INCOME TAXES Wash Sales of Stock Or Securities § 1.1092(c)-1 Qualified covered calls. (a) In.... Under section 1092(d)(3)(B)(i)(I), stock is personal property if the stock is part of a straddle that...

  13. 26 CFR 1.405-1 - Qualified bond purchase plans.

    Science.gov (United States)

    2010-04-01

    ... purchase plan must conform to the definition of a pension plan in paragraph (b)(1)(i) of § 1.401-1, or the.... Accordingly, even though a qualified bond purchase plan is designed as a pension plan, it need not provide... apply in a nondiscriminatory manner. (ii) A qualified bond purchase plan which is designed as a pension...

  14. Use of Acoustic Emission to Monitor Progressive Damage Accumulation in KEVLAR® 49 Composites

    Science.gov (United States)

    Waller, J. M.; Andrade, E.; Saulsberry, R. L.

    2010-02-01

    Acoustic emission (AE) data acquired during intermittent load hold tensile testing of epoxy impregnated Kevlar® 49 (K/Ep) composite strands were analyzed to monitor progressive damage during the approach to tensile failure. Insight into the progressive damage of K/Ep strands was gained by monitoring AE event rate and energy. Source location based on energy attenuation and arrival time data was used to discern between significant AE attributable to microstructural damage and spurious AE attributable to noise. One of the significant findings was the observation of increasing violation of the Kaiser effect (Felicity ratio <1.0) with damage accumulation. The efficacy of three different intermittent load hold stress schedules that allowed the Felicity ratio to be determined analytically is discussed.

  15. Bayes Analysis and Reliability Implications of Stress-Rupture Testing a Kevlar/Epoxy COPV Using Temperature and Pressure Acceleration

    Science.gov (United States)

    Phoenix, S. Leigh; Kezirian, Michael T.; Murthy, Pappu L. N.

    2009-01-01

    Composite Overwrapped Pressure Vessels (COPVs) that have survived a long service time under pressure generally must be recertified before service is extended. Flight certification is dependent on the reliability analysis to quantify the risk of stress rupture failure in existing flight vessels. Full certification of this reliability model would require a statistically significant number of lifetime tests to be performed and is impractical given the cost and limited flight hardware for certification testing purposes. One approach to confirm the reliability model is to perform a stress rupture test on a flight COPV. Currently, testing of such a Kevlar49 (Dupont)/epoxy COPV is nearing completion. The present paper focuses on a Bayesian statistical approach to analyze the possible failure time results of this test and to assess the implications in choosing between possible model parameter values that in the past have had significant uncertainty. The key uncertain parameters in this case are the actual fiber stress ratio at operating pressure, and the Weibull shape parameter for lifetime; the former has been uncertain due to ambiguities in interpreting the original and a duplicate burst test. The latter has been uncertain due to major differences between COPVs in the database and the actual COPVs in service. Any information obtained that clarifies and eliminates uncertainty in these parameters will have a major effect on the predicted reliability of the service COPVs going forward. The key result is that the longer the vessel survives, the more likely the more optimistic stress ratio model is correct. At the time of writing, the resulting effect on predicted future reliability is dramatic, increasing it by about one "nine," that is, reducing the predicted probability of failure by an order of magnitude. However, testing one vessel does not change the uncertainty on the Weibull shape parameter for lifetime since testing several vessels would be necessary.

  16. USE OF COMPOSITE MATERIALS AS A COMPONENT OF TUSK FRACTURE MANAGEMENT IN AN ASIAN ELEPHANT (ELEPHAS MAXIMUS) AND AN AFRICAN ELEPHANT (LOXODONTA AFRICANA).

    Science.gov (United States)

    Sim, Richard R; Stringer, Elizabeth; Donovan, Dennis; Chappell, Rachael; Flora, Pat; Hall, Jon; Pillay, Selvum; Willis, Benjamin G; McCain, Stephanie

    2017-09-01

    Tusk fractures in Asian (Elephas maximus) and African elephants (Loxodonta africana) can result in damage to the distal end or to longitudinal cracks, potentially progressing to pulpitis. With pulp exposure, endodontic therapy is the treatment of choice, but conservative therapy has sufficed for some elephants. This manuscript describes the use of composite materials as a component of tusk fracture management. A 7-yr-old male Asian elephant fractured the distal end of both tusks with pulp exposure in one. Capping of each tusk with a Kevlar/fiberglass composite prevented further damage, and a modification allowed care of the exposed pulp tissue. A 34-yr-old male African elephant with a longitudinal crack received a carbon fiber/fiberglass composite circumferential wrap to potentially stabilize the crack. Compression of the crack was achieved, but follow-up was truncated due to bacterial pulpitis. Both cases show that composite material allows for lightweight, durable management of tusk fractures with continued radiographic monitoring.

  17. The practical skills of newly qualified nurses.

    Science.gov (United States)

    Danbjørg, Dorthe Boe; Birkelund, Regner

    2011-02-01

    This paper reports the findings from a study of newly qualified nurses and which subjects the nurses regarded as the most important in order to be able to live up to the requirements of clinical practice, and how they experience their potential for developing practical and moral skills, after the decrease in practical training. A qualitative approach guided the research process and the analysis of the data. The data was collected by participant observation and qualitative interviews with four nurses as informants. The conclusions made in this study are based on the statements and the observations of the newly qualified nurses. Our findings are discussed in relation to the Aristotelian concept and other relevant literature. The main message is that the newly qualified nurses did not feel equipped when they finished their training. This could be interpreted as a direct consequence of the decrease in practical training. Our study also underlines that the way nursing theory is perceived and taught is problematic. The interviews revealed that the nurses think that nursing theories should be applied directly in practice. This misunderstanding is probably also applicable to the teachers of the theories. Copyright © 2010 Elsevier Ltd. All rights reserved.

  18. Results from Consultancy Meeting on Qualified Technical Centres

    International Nuclear Information System (INIS)

    Novakovic, Mladen

    2017-01-01

    Qualified Technical Centres (QTC) - Current Situation: •Many Member States (MS) need help dealing with DSRS; •Most seek assistance, which can include funding, through the IAEA; •Technical assistance is provided by various governmental organization and private companies (service providers = SP). QTC - Method of Delivery Numerous MS requests are pressing the IAEA’s capacity to assist: •Use qualified internal and external experts/contractors; •Limited pool for DSRS and need to expand; •Dedicated and specialized equipment; •Mobile hot cell; •Mobile tool kit; •Field operations; •Coordinated approach with Nuclear Security and Safety. Qualified Technical Centres for the Management of DSRS: •The challenge is to scale up the support for safe and secure management of DSRS; •Strengthen existing capacity of some MS to support others and make support more sustainable; •Expands the support that can be readily provided and meet the many needs of MS

  19. 48 CFR 225.872-7 - Industrial security for qualifying countries.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Industrial security for... Agreements and Coordination 225.872-7 Industrial security for qualifying countries. The required procedures... qualifying country sources are in the DoD Industrial Security Regulation DoD 5220.22-R (implemented for the...

  20. The Learning Intentions of Low-Qualified Employees: A Multilevel Approach

    Science.gov (United States)

    Kyndt, Eva; Dochy, Filip; Onghena, Patrick; Baert, Herman

    2013-01-01

    In the continuously changing society and knowledge-intensive economy, the demand for the recurrent updating of competencies is coming to the fore for all employees, including low-qualified employees. Employees are considered low qualified when they do not have a starter qualification for higher education. Although many educational studies have…

  1. 29 CFR 779.386 - Restaurants may qualify as exempt 13(a)(2) establishments.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Restaurants may qualify as exempt 13(a)(2) establishments... Service Establishments Restaurants and Establishments Providing Food and Beverage Service § 779.386 Restaurants may qualify as exempt 13(a)(2) establishments. (a) A restaurant may qualify as an exempt retail or...

  2. Investigation of the design of a metal-lined fully wrapped composite vessel under high internal pressure

    Science.gov (United States)

    Kalaycıoğlu, Barış; Husnu Dirikolu, M.

    2010-09-01

    In this study, a Type III composite pressure vessel (ISO 11439:2000) loaded with high internal pressure is investigated in terms of the effect of the orientation of the element coordinate system while simulating the continuous variation of the fibre angle, the effect of symmetric and non-symmetric composite wall stacking sequences, and lastly, a stacking sequence evaluation for reducing the cylindrical section-end cap transition region stress concentration. The research was performed using an Ansys® model with 2.9 l volume, 6061 T6 aluminium liner/Kevlar® 49-Epoxy vessel material, and a service internal pressure loading of 22 MPa. The results show that symmetric stacking sequences give higher burst pressures by up to 15%. Stacking sequence evaluations provided a further 7% pressure-carrying capacity as well as reduced stress concentration in the transition region. Finally, the Type III vessel under consideration provides a 45% lighter construction as compared with an all metal (Type I) vessel.

  3. Qualified-agent virtue ethics | van Zyl | South African Journal of ...

    African Journals Online (AJOL)

    Qualified-agent virtue ethics provides an account of right action in terms of the virtuous agent. It has become one of the most popular, but also most frequently criticized versions of virtue ethics. Many of the objections rest on the mistaken assumption that proponents of qualified-agent virtue ethics share the same view when it ...

  4. Effect of vacuum and temperature on the mechanical properties of an aramid/epoxy composite

    International Nuclear Information System (INIS)

    Hahn, H.T.; Chin, W.K.

    1981-01-01

    The mechanical properties of a Kevlar 49/epoxy composite intended for flywheel applications are investigated in the laboratory and simulated service environments. The filament-wound composites were preconditioned in the test environment for 1-5 months, during which weight change was monitored, then subjected to tensile and fatigue tests at room temperature or 75 deg in vacuum. A weight loss of only 1.63% is observed after 11 months in the simulated service environment, most of which is attributed to moisture desorbed in vacuum. In contrast to air at 75 C, the simulated service environment is also found to produce no deleterious effects on static and fatigue strengths, probably to moisture desorption and a lack of oxidation. A fatigue life of about 100,000 cycles for 95% survival proability is obtained at 70% of the average static strength, and the macroscopic failure mode, which results in a brush-like formation, is observed to be independent of the type of loading and preconditioning. It is concluded that an environment of 75 C in vacuum is no deterrent to the application of the composite in flywheels, however the possibility of increasing service temperature to 150 C should be investigated

  5. Thermal expansion of fibre-reinforced composites

    International Nuclear Information System (INIS)

    Schneider, B.

    1991-07-01

    The integral thermal expansion and the coefficient of thermal expansion (CTE) of carbon and Kevlar fibre-reinforced composites were measured with high accuracy from 5 K to room temperature. For this, a laser dilatometer and a sophisticated measuring procedure were used. CTE dependence on the orientation angle ω of angle-ply laminates was determined for samples with 5 different fibre alignments (UD 0deg, +/-30deg, +/-45deg, +/-60deg and UD 90deg). A high variability of the CTE with the orientation angle was shown. At angles of approximately +/-30deg even negative CTEs were found. With suitable reinforcing fibres being selected, their absolute values rose up to 30-100% of the positive CTEs of metals. Hence, composites of this type would be suitable as compensating materials in metal constructions where little thermal expansion is desired. To check the lamination theory, theoretical computations of the CTE- ω -dependence were compared with the measured values. An excellent agreement was found. Using the lamination theory, predictions about the expansion behaviour of angle-ply laminates can be made now, if the thermal and mechanical properties of the unidirectional (UD) laminate are known. Furthermore, it is possible to carry out simulation computations aimed at investigating the influence of a single parameter of the UD-laminate (e.g. shear modulus) on the expansion of the angle-ply laminate. (orig.) [de

  6. 76 FR 2029 - Small Business Investment Companies-Energy Saving Qualified Investments

    Science.gov (United States)

    2011-01-12

    ... 3245-AF86 Small Business Investment Companies--Energy Saving Qualified Investments AGENCY: U.S. Small... Administration (SBA) is setting forth the new defined terms, ``Energy Saving Qualified Investment'' and ``Energy Saving Activities'', for the Small Business Investment Company (SBIC) Program. The new definitions are...

  7. Effect of γ-irradiation on the optical and electrical properties of fiber reinforced composites

    International Nuclear Information System (INIS)

    Anwar, Ahmad; Elfiky, Dalia; Ramadan, Ahmed M.; Hassan, G.M.

    2017-01-01

    The effect of gamma irradiation on the optical and electrical properties of the reinforced fiber polymeric based materials became an important issue. Fiberglass/epoxy and Kevlar fiber/epoxy were selected as investigated samples manufactured with hand lay-up without autoclave curing technique. The selected technique is simple and low cost while being rarely used in space materials production. The electric conductivity and dielectric constant for those samples were measured with increasing the gamma radiation dose. Moreover, the absorptivity, band gap and color change were determined. Fourier transform infrared (FTIR) was performed to each of the material's constituent to evaluate the change in the investigated materials due to radiation exposure dose. In this study, the change of electrical properties for both investigated materials showed a slight variation of the test parameters with respect to the gamma dose increase; this variation is placed in the insulators rang. The tested samples showed an insulator stable behavior during the test period. The change of optical properties for both composite specimens showed the maximum absorptivity at the gamma dose 750 kGy. These materials are suitable for structure materials and thermal control for orbital life less than 7 years. In addition, the transparency of epoxy matrix was degraded. However, there is no color change for either Kevlar fiber or fiberglass. - Highlights: • Space qualification for the reinforced fiber polymeric based materials which will be used for satellite structure. • Change of optical and electrical properties for selected material under the effect of gamma radiation. • Using a simple and low cost manufacturing method for space materials.

  8. 14 CFR 1214.1104 - Evaluation and ranking of highly qualified candidates.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Evaluation and ranking of highly qualified candidates. 1214.1104 Section 1214.1104 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION... ranking of highly qualified candidates. (a) A selection board consisting of discipline experts, and such...

  9. 8 CFR 214.14 - Alien victims of certain qualifying criminal activity.

    Science.gov (United States)

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Alien victims of certain qualifying criminal activity. 214.14 Section 214.14 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY IMMIGRATION REGULATIONS NONIMMIGRANT CLASSES § 214.14 Alien victims of certain qualifying criminal activity. (a...

  10. 13 CFR 126.204 - May a qualified HUBZone SBC have affiliates?

    Science.gov (United States)

    2010-01-01

    ... affiliates? 126.204 Section 126.204 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION HUBZONE PROGRAM Requirements to be a Qualified HUBZone SBC § 126.204 May a qualified HUBZone SBC have affiliates? A concern may have affiliates provided that the aggregate size of the concern and all of its...

  11. 13 CFR 108.110 - Qualified management.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Qualified management. 108.110... management. An Applicant must show, to the satisfaction of SBA, that its current or proposed management team... or proposed management team has sufficient qualifications, SBA will consider information provided by...

  12. Factor Structure of the Air Force Officer Qualifying Test: Analysis and Comparison

    National Research Council Canada - National Science Library

    Carreta, Thomas

    1998-01-01

    The Air Force Officer Qualifying Test (AFOQT) is used to qualify men and women for commissions in the Air Force, classify them for pilot and navigator jobs, and award Reserve Officer Training Corps (ROTC) scholarships...

  13. 46 CFR 390.9 - Qualified withdrawals.

    Science.gov (United States)

    2010-10-01

    ..., construction or reconstruction its fair market value. The party must obtain the prior written permission of the... appraisal to be the fair market value of the vessel, at the time of the acquisition, or the actual cost...: (i) The acquisition, construction or reconstruction of a qualified agreement vessel; (ii) The...

  14. 26 CFR 1.401-7 - Forfeitures under a qualified pension plan.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 5 2010-04-01 2010-04-01 false Forfeitures under a qualified pension plan. 1...) INCOME TAX (CONTINUED) INCOME TAXES Pension, Profit-Sharing, Stock Bonus Plans, Etc. § 1.401-7 Forfeitures under a qualified pension plan. (a) General rules. In the case of a trust forming a part of a...

  15. 26 CFR 1.401(a)-11 - Qualified joint and survivor annuities.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 5 2010-04-01 2010-04-01 false Qualified joint and survivor annuities. 1.401(a...)-11 Qualified joint and survivor annuities. (a) General rule—(1) Required provisions. A trust, to...), which is a part of a plan providing for the payment of benefits in any form of a life annuity (as...

  16. Multi-Level Experimental and Analytical Evaluation of Two Composite Energy Absorbers

    Science.gov (United States)

    Jackson, Karen E.; Littell, Justin D.; Fasanella, Edwin L.; Annett, Martin S.; Seal, Michael D., II

    2015-01-01

    Two composite energy absorbers were developed and evaluated at NASA Langley Research Center through multi-level testing and simulation performed under the Transport Rotorcraft Airframe Crash Testbed (TRACT) research program. A conical-shaped energy absorber, designated the conusoid, was evaluated that consisted of four layers of hybrid carbon-Kevlar plain weave fabric oriented at [+45 deg/-45 deg/-45 deg/+45 deg] with respect to the vertical, or crush, direction. A sinusoidal-shaped energy absorber, designated the sinusoid, was developed that consisted of hybrid carbon-Kevlar plain weave fabric face sheets, two layers for each face sheet oriented at +/-45deg with respect to the vertical direction and a closed-cell ELFOAM P200 polyisocyanurate (2.0-lb/cu ft) foam core. The design goal for the energy absorbers was to achieve average floor-level accelerations of between 25- and 40-g during the full-scale crash test of a retrofitted CH-46E helicopter airframe, designated TRACT 2. Variations in both designs were assessed through dynamic crush testing of component specimens. Once the designs were finalized, subfloor beams of each configuration were fabricated and retrofitted into a barrel section of a CH-46E helicopter. A vertical drop test of the barrel section was conducted onto concrete to evaluate the performance of the energy absorbers prior to retrofit into TRACT 2. The retrofitted airframe was crash tested under combined forward and vertical velocity conditions onto soil, which is characterized as a sand/clay mixture. Finite element models were developed of all test articles and simulations were performed using LS-DYNA, a commercial nonlinear explicit transient dynamic finite element code. Test-analysis results are presented for each energy absorber as comparisons of time-history responses, as well as predicted and experimental structural deformations and progressive damage under impact loading for each evaluation level.

  17. 26 CFR 20.2056A-2 - Requirements for qualified domestic trust.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Requirements for qualified domestic trust. 20.2056A-2 Section 20.2056A-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) ESTATE AND GIFT TAXES ESTATE TAX; ESTATES OF DECEDENTS DYING AFTER AUGUST 16, 1954 Taxable Estate § 20.2056A-2 Requirements for qualified...

  18. 26 CFR 1.1092(c)-3 - Qualifying over-the-counter options.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 11 2010-04-01 2010-04-01 true Qualifying over-the-counter options. 1.1092(c)-3...-counter options. (a) In general. Under section 1092(c)(4)(B)(i), an equity option is not a qualified covered call option unless it is traded on a national securities exchange that is registered with the...

  19. 26 CFR 11.401(a)-11 - Qualified joint and survivor annuities.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Qualified joint and survivor annuities. 11.401... SECURITY ACT OF 1974 § 11.401(a)-11 Qualified joint and survivor annuities. (a) In general—(1) General rule... annuity (i.e., an annuity requiring survival of the participant or his spouse as a condition for payment...

  20. Competence of newly qualified registered nurses from a nursing college

    Directory of Open Access Journals (Sweden)

    BG Morolong

    2005-09-01

    Full Text Available The South African education and training system, through its policy of outcomesbased education and training, has made competency a national priority. In compliance to this national requirement of producing competent learners, the South African Nursing Council ( 1999 B require that the beginner professional nurse practitioners and midwives have the necessary knowledge, skills, attitudes and values which will enable them to render efficient professional service. The health care system also demands competent nurse practitioners to ensure quality in health care. In the light of competency being a national priority and a statutory demand, the research question that emerges is, how competent are the newly qualified registered nurses from a specific nursing college in clinical nursing education? A quantitative, non-experimental contextual design was used to evaluate the competence of newly qualified registered nurses from a specific nursing college. The study was conducted in two phases. The first phase dealt with the development of an instrument together with its manual through the conceptualisation process. The second phase focused on the evaluation of the competency of newly qualified nurses using the instrument based on the steps of the nursing process. A pilot study was conducted to test the feasibility of the items of the instrument. During the evaluation phase, a sample of twenty-six newly qualified nurses was selected by simple random sampling from a target population of thirty-six newly qualified registered nurses. However, six participants withdrew from the study. Data was collected in two general hospitals where the newly qualified registered nurses were working. Observation and questioning were used as data collection techniques in accordance with the developed instrument. Measures were taken to ensure internal validity and reliability of the results. To protect the rights of the participants, the researcher adhered to DENOSA’S (1998

  1. 7 CFR 785.8 - Reports by qualifying States receiving mediation grant funds.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Reports by qualifying States receiving mediation grant... SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS CERTIFIED STATE MEDIATION PROGRAM § 785.8 Reports by qualifying States receiving mediation grant funds. (a) Annual report by certified State...

  2. Differential water sorption studies on Kevlar 49 and As-polymerized poly(p-phenylene terephthalamide): determination of water transport properties.

    Science.gov (United States)

    Mooney, Damian A; MacElroy, J M Don

    2007-11-06

    Water vapor sorption experiments have been conducted on Kevlar 49 at 30 degrees C over a range of water vapor pressures in 0-90% of saturation and on the as-polymerized form of the material at 30, 45, and 60 degrees C over a series of water vapor pressures of 0-60%, 0-25%, and 0-15%, respectively. For each of the differential steps in water vapor pressure, dynamic uptake curves were generated and analyzed according to a number of different mathematical models, including Fickian, Coaxial cylindrical, and intercalation models. The intercalation model was demonstrated to be the most successful model and considered two time-scales involved in the diffusion process, i.e., a penetrant-diffusive time-scale and a polymer-local-matrix-relaxation time-scale. The success of this model reinforces previously reported adsorption and desorption isotherms which suggested that water may penetrate into the surface layers of the polymer crystallite through a process known as intercalation.

  3. IEEE 693 seismic qualification of composites for substation high-voltage equipment

    Energy Technology Data Exchange (ETDEWEB)

    Schiff, A.J. [Precision Measurement Instruments, Los Altos Hills, CA (United States); Kempner, L.Jr. [Bonneville Power Administration, Vancouver, BC (Canada)

    2004-07-01

    Standard 693-1997 of the Institute of Electrical and Electronic Engineers (IEEE) is the recommended practice for seismic design of substations. It represents a significant improvement in the way the power industry seismically qualifies substation high-voltage equipment. This paper described the use of IEEE Standard 693 for hollow-core composite insulators that are used on high-voltage transformers and demonstrated that changes are warranted. The following four failure modes associated with the composite insulator were discussed: bond degradation, bond failure, tube degradation and tube layer delamination. The authors evaluated the IEEE 693 qualification procedure of time history shake-table and static-pull tests and were concerned about acceptance criteria. It was shown that acceptance criteria are not valid for qualifying hollow-core composites and that static-pull tests are needed after the vibration qualification tests are completed. It was suggested that more research is warranted to determine if bonding at the top part of the flange can be eliminated, thereby eliminating bond degradation. The resulting increase in system damping would improve the dynamic response of the unit. 1 ref., 10 figs.

  4. 41 CFR 102-80.135 - Who is a qualified fire protection engineer?

    Science.gov (United States)

    2010-07-01

    ... protection engineer? 102-80.135 Section 102-80.135 Public Contracts and Property Management Federal Property... qualified fire protection engineer? A qualified fire protection engineer is defined as an individual with a thorough knowledge and understanding of the principles of physics and chemistry governing fire growth...

  5. 26 CFR 1.883-4T - Qualified shareholder stock ownership test (temporary).

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Qualified shareholder stock ownership test... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Foreign Corporations § 1.883-4T Qualified shareholder stock... the stock; (D) If the individual directly owns an interest in a corporation, partnership, trust...

  6. 26 CFR 1.181-3T - Qualified film or television production (temporary).

    Science.gov (United States)

    2010-04-01

    ... season of programming. (3) Exception for certain sexually explicit productions. A production does not... 26 Internal Revenue 3 2010-04-01 2010-04-01 false Qualified film or television production... (continued) § 1.181-3T Qualified film or television production (temporary). (a) In general. The term...

  7. Balance carried out on an alpha waste incinerator in order to qualify its filtration system

    International Nuclear Information System (INIS)

    Cartier, R.; Burghofer, P.; Tregoures, A.; Maurel, J.M.; Vendel, J.

    1991-01-01

    A balance was carried out on a pilot incinerator of inactive solid waste running at 4 kg/h. Various measurements were taken in order to qualify the prefiltration system of the incineration process operating by pyrolysis, afterburning and calcination: determining the ventilation characteristics of the plant (gas flow rates and residence time) and the physico-chemical characteristics of the effluent (mass flow and granulometric range of particles, chemical composition of gases). Various methods of sampling and of analyzing the gases were adopted and a thermochemical model was produced. Its results are reasonably close to the experimental measurements. The emission consists of submicronic particles and porous layers are the best adapted cleaning system

  8. Job satisfaction of overseas-qualified nurses working in Australian hospitals.

    Science.gov (United States)

    Timilsina Bhandari, K K; Xiao, L D; Belan, I

    2015-03-01

    The aims of this study were to explore factors associated with the job satisfaction of overseas-qualified nurses working in public hospitals in South Australia and to compare whether factors associated with job satisfaction of overseas nurses from English-speaking backgrounds differed from those from non-English-speaking backgrounds. Overseas-qualified nurses have become an essential part of the nursing workforce in Australia. Although this nurse population has different expectations and values in relation to their jobs when compared with local nurses, studies on job satisfaction among overseas nurses are scarce. A cross-sectional survey using the Job Satisfaction of Overseas-Qualified Nurses questionnaire was conducted in five major public hospitals in South Australia. One hundred and fifty-one overseas-qualified nurses completed the questionnaire. Four factors were found to influence job satisfaction: Supportive work environment, interpersonal relationships, communication in English, and salary and salary-related benefits. Communication in English was the predominant factor that was associated with job satisfaction in nurses from non-English-speaking backgrounds. This group of nurses also showed a negative correlation between length of stay in Australia and satisfaction with their work environment. Participants' responses to open-ended questions revealed issues relating to discrimination and racism. Supportive work environment, interpersonal relationships, communication in English, and salary and salary-related benefits were major factors associated with job satisfaction in overseas-qualified nurses in this study. Nurses from non-English-speaking backgrounds faced additional challenges in communication in the workplace and in dealing with issues of discrimination and racism. Nurses from non-English-speaking backgrounds need to be supported early in their employment, especially with their communication skills. Consideration also needs to be given to the education

  9. Qualified operator training in the simulated control room environment

    International Nuclear Information System (INIS)

    Ionescu, Teodor; Studineanu, Emil; Radulescu, Catalina; Bolocan, Gabriel

    2005-01-01

    Full text: Mainly designed for the training of the Cernavoda NPP Unit 2 operators, the virtual simulated environment allows the training of the already qualified operators for Cernavoda NPP Unit 1, adding to the already trained knowledge, the differences which has occurred in the Unit 2 design. Using state-of-the-art computers and displays and qualified software, the virtual simulated panels could offer a viable alternative to classic hardware-based training. This approach allows quick training of the new procedures required by the new configuration of the re-designed operator panels in the main control room of Cernavoda NPP Unit 2. (authors)

  10. Qualified operator training in the simulated control room environment

    International Nuclear Information System (INIS)

    Ionescu, Teodor; Studineanu, Emil; Radulescu, Catalina; Bolocan, Gabriel

    2005-01-01

    Mainly designed for the training of the Cernavoda NPP Unit 2 operators, the virtual simulated environment allows the training of the already qualified operators for Cernavoda NPP Unit 1, adding to the already trained knowledge, the differences which have occurred in the Unit 2 design. Using state-of-the-art computers and displays and qualified software, the virtual simulated panels could offer a viable alternative to classic hardware-based training. This approach allows quick training of the new procedures required by the new configuration of the re-designed operator panels in the main control room of Cernavoda NPP Unit 2. (authors)

  11. Profitability of Qualified-Labour-Power Production

    Science.gov (United States)

    Baldino, Roberto Ribeiro; Cabral, Tânia Cristina Baptista

    2015-01-01

    In Baldino and Cabral (2013) we introduced the concept of qualified labour-power as the commodity produced by the school system. In the present article we outline a quantitative model to evaluate the profit rate of educational programmes. We compare a medical school programme with a teacher education programme at a public university in Brazil,…

  12. Tricks of the trade: time management tips for newly qualified doctors.

    Science.gov (United States)

    Offiah, Gozie; Doherty, Eva

    2018-03-01

    The transition from medical student to doctor is an important milestone. The discovery that their time is no longer their own and that the demands of their job are greater than the time they have available is extremely challenging. At a recent surgical boot camp training programme, 60 first-year surgical trainees who had just completed their internship were invited to reflect on the lessons learnt regarding effective time management and to recommend tips for their newly qualified colleagues. They were asked to identify clinical duties that were considered urgent and important using the time management matrix and the common time traps encountered by newly qualified doctors. The surgical trainees identified several practical tips that ranged from writing a priority list to working on relationships within the team. These tips are generic and so applicable to all newly qualified medial doctors. We hope that awareness of these tips from the outset as against learning them through experience will greatly assist newly qualified doctors. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  13. 'Practising under your own Pin'- a description of the transition experiences of newly qualified midwives.

    Science.gov (United States)

    Avis, Mark; Mallik, Maggie; Fraser, Diane M

    2013-11-01

    Transition experiences of newly qualified midwives were examined in depth during the third phase of a UK evaluation study of midwifery education. The fitness to practise and the retention of newly qualified nursing and midwifery graduates are pressing concerns for health care managers. The advantages of preceptorship are reported in the literature but the content and timing of schemes remain unclear. A semi-structured diary was kept for up to 6 months by 35 newly qualified midwives in 18 work sites covering all countries in the UK. The preceptor and supervisor of midwives for each newly qualified midwife completed short questionnaires about their preceptee's performance, and a further sub-sample of newly qualified midwives and preceptors participated in a semi-structured interview. Data were analysed to elicit aspects of newly qualified midwives transition experiences. Findings confirm that structured preceptorship schemes are not widely available. Newly qualified midwives primarily obtained transition support from members of the midwifery team. Although perceived as competent, there is no demarcation point in becoming confident to practise as a registered practitioner. Implications for managers include the importance of a supportive culture within clinical teams for successful transition and the introduction of structured preceptorship schemes facilitated by appropriate rotation patterns. © 2012 John Wiley & Sons Ltd.

  14. 26 CFR 1.468B-2 - Taxation of qualified settlement funds and related administrative requirements.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 6 2010-04-01 2010-04-01 false Taxation of qualified settlement funds and... Taken § 1.468B-2 Taxation of qualified settlement funds and related administrative requirements. (a) In...) of this section is in lieu of any other taxation of the income of a qualified settlement fund under...

  15. High Kinetic Energy Penetrator Shielding and High Wear Resistance Materials Fabricated with Boron Nitride Nanotubes (BNNTS) and BNNT Polymer Composites

    Science.gov (United States)

    Kang, Jin Ho (Inventor); Sauti, Godfrey (Inventor); Smith, Michael W. (Inventor); Jordan, Kevin C. (Inventor); Park, Cheol (Inventor); Bryant, Robert George (Inventor); Lowther, Sharon E. (Inventor)

    2015-01-01

    Boron nitride nanotubes (BNNTs), boron nitride nanoparticles (BNNPs), carbon nanotubes (CNTs), graphites, or combinations, are incorporated into matrices of polymer, ceramic or metals. Fibers, yarns, and woven or nonwoven mats of BNNTs are used as toughening layers in penetration resistant materials to maximize energy absorption and/or high hardness layers to rebound or deform penetrators. They can be also used as reinforcing inclusions combining with other polymer matrices to create composite layers like typical reinforcing fibers such as Kevlar.RTM., Spectra.RTM., ceramics and metals. Enhanced wear resistance and usage time are achieved by adding boron nitride nanomaterials, increasing hardness and toughness. Such materials can be used in high temperature environments since the oxidation temperature of BNNTs exceeds 800.degree. C. in air. Boron nitride based composites are useful as strong structural materials for anti-micrometeorite layers for spacecraft and space suits, ultra strong tethers, protective gear, vehicles, helmets, shields and safety suits/helmets for industry.

  16. Partners in qualified equipment supply

    International Nuclear Information System (INIS)

    Rygg, D.E.; O'Hare, G.J.

    1993-01-01

    Industry initiatives have been taken to improve procurement practices and commercial dedication programs, formation of procurement engineering groups, emphasis on product quality, and increased engineering involvement in procurement and maintenance of qualified equipment. This poses new challenges for many licensees in terms of resources, product knowledge, and access to information normally held proprietary by equipment suppliers. Alternative approaches to future licensee/Westinghouse relationships which will allow licensees to adapt to the changing environment are discussed. 2 figs

  17. 29 CFR 779.382 - May qualify as exempt 13(a)(2) establishments.

    Science.gov (United States)

    2010-07-01

    ... STANDARDS ACT AS APPLIED TO RETAILERS OF GOODS OR SERVICES Exemptions for Certain Retail or Service Establishments Hotels and Motels § 779.382 May qualify as exempt 13(a)(2) establishments. A hotel or motel establishment may qualify as an exempt retail or service establishment under section 13(a)(2) of the Act...

  18. Space-Qualified Traveling-Wave Tube

    Science.gov (United States)

    Wilson, Jeffrey D.; Krawczyk, Richard; Simons, Rainee N.; Williams, Wallace D.; Robbins, Neal R.; Dibb, Daniel R.; Menninger, William L.; Zhai, Xiaoling; Benton, Robert T.

    2010-01-01

    The L-3 Communications Electron Technologies, Inc. Model 999HA traveling-wave tube (TWT), was developed for use as a high-power microwave amplifier for high-rate transmission of data and video signals from deep space to Earth (see figure). The 999HA is a successor to the 999H a non-space qualified TWT described in High-Power, High-Efficiency Ka-Band Traveling-Wave Tube (LEW-17900-1), NASA Tech Briefs, Vol. 31, No. 2 (February 2007), page 32. Operating in the 31.8-to-32.3 GHz frequency band, the 999HA has been shown to generate 252 W of continuous- wave output power at 62 percent overall power efficiency a 75-percent increase in output power over the 999H. The mass of the 999HA is 35 percent less than that of the 999H. Moreover, taking account of the elimination of a Faraday cage that is necessary for operation of the 999H but is obviated by a redesign of high-voltage feed-throughs for the 999HA, the overall reduction in mass becomes 57 percent with an 82 percent reduction in volume. Through a series of rigorous tests, the 999HA has been qualified for operation aboard spacecraft with a lifetime exceeding seven years. Offspring of the 999HA will fly on the Kepler and Lunar Reconnaissance Orbiter missions.

  19. Going beyond "highly-qualified personnel" to "value-added personnel"

    Science.gov (United States)

    Nantel, Marc; Fox, Bradley; Gelsthorpe, Leanne; Hamilton, Roxy; Marshall, Robert; Williamson, Guida

    2005-10-01

    Employers clamour for more "Highly-Qualified Personnel" (HQP) to hire, and photonics is no exception. The challenge facing all new graduates lies in what actually constitutes a Highly-Qualified Person. Yesterday, an HQP was often understood to be a graduate with a Bachelor's, Master's or Ph.D. degree. Today, industry is demanding that an HQP be either a university or college graduate with strong academic standing AND a sound business and communications skill set. In this paper, we introduce the concept of "Value-Added Personnel" (VAP), which marries both scientific and "soft-skills" aspects, and we present a new program in Ontario to produce VAPs.

  20. 26 CFR 1.989(a)-1 - Definition of a qualified business unit.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 10 2010-04-01 2010-04-01 false Definition of a qualified business unit. 1.989... definition of the term “qualified business unit” (QBU) within the meaning of section 989. (2) Effective date... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Export Trade Corporations § 1.989(a)-1 Definition of a...

  1. Forthcoming Issue

    Indian Academy of Sciences (India)

    THE INFLUENCE OF CARBON CONTENT ON THE MICROSTRUCTURE, MECHANICAL AND TRIBOLOGICAL PROPERTIES OF CrAlCN COATINGS DEPOSITED BY ... of hydroxyapatite/alumina ceramic nanocomposites for biomedical applications ... Properties of Shear Thickening Fluid Impregnated Kevlar Composites.

  2. 9 CFR 85.6 - Interstate movement of pseudorabies vaccinate swine, except swine from qualified negative gene...

    Science.gov (United States)

    2010-01-01

    ... vaccinate swine, except swine from qualified negative gene-altered vaccinated herds, not known to be..., except swine from qualified negative gene-altered vaccinated herds, not known to be infected with or exposed to pseudorabies. Pseudorabies vaccinate swine, except swine from qualified negative gene-altered...

  3. Automatic defects recognition in composite aerospace structures from experimental and theoretical analysis as part of an intelligent infrared thermographic inspection system

    Science.gov (United States)

    David, Denis G. F.; Marin, J. Y.; Tretout, Herve R.

    An original concept for IR thermography nondestructive testing is validated. The principles of image and data processing investigated and developed as well as the utilization of AI should be transposable to other nondestructive techniques such as ultrasounds and X-rays. It is shown that modeling can be used in different ways to play a great part in the detection, the interpretation, and the sizing of the defects. The original concept lies in the comparison of experimental data with theoretical ones in order to identify regions of abnormal behavior related to defects. A Laplace transforms analytical method is successfully implemented in the case of composite materials such as graphite epoxy to identify a set of thermal parameters which contributes to the expertise. This approach is extended to a more complicated composite material such as Kevlar, which presents semitransparent characteristics. This modeling technique, which expresses experimental data in terms of thermal parameters, makes it possible to increase SNR and reduce the number of thermal images to be processed.

  4. Newly qualified teachers´ possibilities to get foothold in a lifelong career course

    DEFF Research Database (Denmark)

    Krøjgaard, Frede; Frederiksen, Lisbeth Angela Lunde

    Keyword: Induction program, newly qualified teachers, NQT, retention, professional development In Contrary to many other countries in Europe Denmark does not have any kind of national program regarding teacher induction program (TIP) or support in general to newly qualified teachers what so ever...

  5. 75 FR 1831 - Seeks Qualified Candidates for the Advisory Committee on Reactor Safeguards

    Science.gov (United States)

    2010-01-13

    ... NUCLEAR REGULATORY COMMISSION Seeks Qualified Candidates for the Advisory Committee on Reactor... Regulatory Commission (NRC) seeks qualified candidates for the Advisory Committee on Reactor Safeguards (ACRS... amended. ACRS provides independent expert advice on matters related to the safety of existing and proposed...

  6. Bioenvironmental Engineering Guide for Composite Materials

    Science.gov (United States)

    2014-03-31

    encountered in the Air Force are glass, boron, carbon/graphite, and aramid (commonly known as Kevlar ®). Glass fibers can be bound together by polymer...fiber hazard as well contact hazards from related chemicals to include resins, epoxies , 8 Distribution A: Approved for public release; distribution...operations, there can be additional hazards from solvents, epoxies , and resins before and/or after the processes described in section 2.0 of this guide

  7. A spectral profile multiplexed FBG sensor network with application to strain measurement in a Kevlar woven fabric

    Science.gov (United States)

    Guo, Guodong; Hackney, Drew; Pankow, Mark; Peters, Kara

    2017-04-01

    A spectral profile division multiplexed fiber Bragg grating (FBG) sensor network is described in this paper. The unique spectral profile of each sensor in the network is identified as a distinct feature to be interrogated. Spectrum overlap is allowed under working conditions. Thus, a specific wavelength window does not need to be allocated to each sensor as in a wavelength division multiplexed (WDM) network. When the sensors are serially connected in the network, the spectrum output is expressed through a truncated series. To track the wavelength shift of each sensor, the identification problem is transformed to a nonlinear optimization problem, which is then solved by a modified dynamic multi-swarm particle swarm optimizer (DMS-PSO). To demonstrate the application of the developed network, a network consisting of four FBGs was integrated into a Kevlar woven fabric, which was under a quasi-static load imposed by an impactor head. Due to the substantial radial strain in the fabric, the spectrums of different FBGs were found to overlap during the loading process. With the developed interrogating method, the overlapped spectrum would be distinguished thus the wavelength shift of each sensor can be monitored.

  8. Strain Rate Dependent Behavior and Modeling for Compression Response of Hybrid Fiber Reinforced Concrete

    Directory of Open Access Journals (Sweden)

    S.M. Ibrahim

    Full Text Available Abstract This paper investigates the stress-strain characteristics of Hybrid fiber reinforced concrete (HFRC composites under dynamic compression using Split Hopkinson Pressure Bar (SHPB for strain rates in the range of 25 to 125 s-1. Three types of fibers - hooked ended steel fibers, monofilament crimped polypropylene fibers and staple Kevlar fibers were used in the production of HFRC composites. The influence of different fibers in HFRC composites on the failure mode, dynamic increase factor (DIF of strength, toughness and strain are also studied. Degree of fragmentation of HFRC composite specimens increases with increase in the strain rate. Although the use of high percentage of steel fibers leads to the best performance but among the hybrid fiber combinations studied, HFRC composites with relatively higher percentage of steel fibers and smaller percentage of polypropylene and Kevlar fibers seem to reflect the equally good synergistic effects of fibers under dynamic compression. A rate dependent analytical model is proposed for predicting complete stress-strain curves of HFRC composites. The model is based on a comprehensive fiber reinforcing index and complements well with the experimental results.

  9. 26 CFR 1.6050S-4 - Information reporting for payments of interest on qualified education loans.

    Science.gov (United States)

    2010-04-01

    ... on qualified education loans. 1.6050S-4 Section 1.6050S-4 Internal Revenue INTERNAL REVENUE SERVICE... Information reporting for payments of interest on qualified education loans. (a) Electronic furnishing of... payments of interest on qualified education loans (furnisher) to the individual to whom it is required to...

  10. Design, fabrication, installation and flight service evaluation of a composite cargo ramp skin on a model CH-53 helicopter

    Science.gov (United States)

    Lowry, D. W.; Rich, M. J.

    1983-01-01

    The installation of a composite skin panel on the cargo ramp of a CH-530 marine helicopter is discussed. The composite material is of Kevlar/Epoxy (K/E) which replaces aluminum outer skins on the aft two bays of the ramp. The cargo ramp aft region was selected as being a helicopter airframe surface subjected to possible significant field damage and would permit an evaluation of the long term durability of the composite skin panel. A structural analysis was performed and the skin shears determined. Single lap joints of K/E riveted to aluminum were statically tested. The joint tests were used to determine bearing allowables and the required K/E skin gage. The K/E skin panels riveted to aluminum edge members were tested in a shear fixture to confirm the allowable shear and bearing strengths. Impact tests were conducted on aluminum skin panels to determine energy level and damage relationship. The K/E skin panels of various ply orientations and laminate thicknesses were then impacted at similar energy levels. The results of the analysis and tests were used to determine the required K/E skin gages in each of the end two bays of the ramp.

  11. 26 CFR 1.127-1 - Amounts received under a qualified educational assistance program.

    Science.gov (United States)

    2010-04-01

    ... employee under a qualified educational assistance program described in § 1.127-2, or (2) The value of... Income § 1.127-1 Amounts received under a qualified educational assistance program. (a) Exclusion from.... (c) Amounts received under a nonqualified program. Any amount received under an educational...

  12. 49 CFR 40.281 - Who is qualified to act as a SAP?

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Who is qualified to act as a SAP? 40.281 Section... § 40.281 Who is qualified to act as a SAP? To be permitted to act as a SAP in the DOT drug and alcohol.... (2) You must be knowledgeable about the SAP function as it relates to employer interests in safety...

  13. ISS qualified thermal carrier equipment

    Science.gov (United States)

    Deuser, Mark S.; Vellinger, John C.; Jennings, Wm. M.

    2000-01-01

    Biotechnology is undergoing a period of rapid and sustained growth, a trend which is expected to continue as the general population ages and as new medical treatments and products are conceived. As pharmaceutical and biomedical companies continue to search for improved methods of production and, for answers to basic research questions, they will seek out new avenues of research. Space processing on the International Space Station (ISS) offers such an opportunity! Space is rapidly becoming an industrial laboratory for biotechnology research and processing. Space bioprocessing offers exciting possibilities for developing new pharmaceuticals and medical treatments, which can be used to benefit mankind on Earth. It also represents a new economic frontier for the private sector. For over eight years, the thermal carrier development team at SHOT has been working with government and commercial sector scientists who are conducting microgravity experiments that require thermal control. SHOT realized several years ago that the hardware currently being used for microgravity thermal control was becoming obsolete. It is likely that the government, academic, and industrial bioscience community members could utilize SHOT's hardware as a replacement to their current microgravity thermal carrier equipment. Moreover, SHOT is aware of several international scientists interested in utilizing our space qualified thermal carrier. SHOT's economic financing concept could be extremely beneficial to the international participant, while providing a source of geographic return for their particular region. Beginning in 2000, flight qualified thermal carriers are expected to be available to both the private and government sectors. .

  14. Doctors qualifying from United Kingdom medical schools during the calendar years 1977 and 1983.

    Science.gov (United States)

    Parkhouse, J; Parkhouse, H F

    1989-01-01

    At the conclusion of undergraduate medical education in the United Kingdom most students pass a university qualifying examination and obtain a degree in medicine and surgery. Some students pass an external non-university qualifying examination in medicine as an alternative to obtaining a degree, and some do both. The degree may be obtained in the same year as the non-university qualifying examination, or in a different year. Some students from a medical school intake qualify in a later year than expected, for various reasons. Data from university, Health Department and other sources may relate to the academic year, the calendar year, or a fixed date such as 30 September. It is not a simple exercise, therefore, to define the exact number of people who qualify to practise medicine, for the first time, in any given 'year'. In counting qualifiers from individual medical schools, the problems are further compounded by the movement of students between the preclinical and clinical stages of the course, particularly from Oxford and Cambridge to London teaching hospitals. This paper analyses the situation for the calendar years 1977 and 1983, showing a decline in the number of students obtaining double (i.e. both university and non-university) qualifications. The number of UK graduates not registering with the General Medical Council to practise, at least for a time, in the UK was small, and the population base compiled for Medical Career Research Group studies was reasonably accurate in each of the 2 years examined.

  15. Are reactive thermoplastic polymers suitable for future wind turbine composite materials blades?

    DEFF Research Database (Denmark)

    Raghavalu Thirumalai, Durai Prabhakaran

    2014-01-01

    , it was found that only two potential reactive thermoplastic resin systems qualify for different processing requirements for blade manufacturing. Hence, the article focuses on the issues with the use of reactive polymers like APA-6 (Caprolactam) and CBT (Cyclic Butylene Terephtalate) resin systems for composite...

  16. 26 CFR 1.1293-1 - Current taxation of income from qualified electing funds.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 11 2010-04-01 2010-04-01 true Current taxation of income from qualified electing funds. 1.1293-1 Section 1.1293-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE... Losses § 1.1293-1 Current taxation of income from qualified electing funds. (a) In general. [Reserved] (1...

  17. Armored garment for protecting

    Science.gov (United States)

    Purvis, James W [Albuquerque, NM; Jones, II, Jack F.; Whinery, Larry D [Albuquerque, NM; Brazfield, Richard [Albuquerque, NM; Lawrie, Catherine [Tijeras, NM; Lawrie, David [Tijeras, NM; Preece, Dale S [Watkins, CO

    2009-08-11

    A lightweight, armored protective garment for protecting an arm or leg from blast superheated gases, blast overpressure shock, shrapnel, and spall from a explosive device, such as a Rocket Propelled Grenade (RPG) or a roadside Improvised Explosive Device (IED). The garment has a ballistic sleeve made of a ballistic fabric, such as an aramid fiber (e.g., KEVLAR.RTM.) cloth, that prevents thermal burns from the blast superheated gases, while providing some protection from fragments. Additionally, the garment has two or more rigid armor inserts that cover the upper and lower arm and protect against high-velocity projectiles, shrapnel and spall. The rigid inserts can be made of multiple plies of a carbon/epoxy composite laminate. The combination of 6 layers of KEVLAR.RTM. fabric and 28 plies of carbon/epoxy laminate inserts (with the inserts being sandwiched in-between the KEVLAR.RTM. layers), can meet the level IIIA fragmentation minimum V.sub.50 requirements for the US Interceptor Outer Tactical Vest.

  18. Predictors of Self-Directed Learning for Low-Qualified Employees: A Multi-Level Analysis

    Science.gov (United States)

    Raemdonck, Isabel; van der Leeden, Rien; Valcke, Martin; Segers, Mien; Thijssen, Jo

    2012-01-01

    Purpose: This study aims to examine which variables at the level of the individual employee and at the company level are predictors of self-directed learning in low-qualified employees. Methodology: Results were obtained from a sample of 408 low-qualified employees from 35 different companies. The companies were selected from the energy sector,…

  19. Attempting to Predict Success in the Qualifying Round of the International Chemistry Olympiad

    Science.gov (United States)

    Urhahne, Detlef; Ho, Lok Hang; Parchmann, Ilka; Nick, Sabine

    2012-01-01

    The aim of this study was trying to predict success in the qualifying round for the International Chemistry Olympiad (IChO) on the basis of the expectancy-value model of achievement motivation by Eccles et al. The investigation with 52 participants, including 14 females, was conducted during the third of four qualifying rounds of the IChO in…

  20. 7 CFR 1466.11 - Technical services provided by qualified personnel not affiliated with USDA.

    Science.gov (United States)

    2010-01-01

    ... not affiliated with USDA. 1466.11 Section 1466.11 Agriculture Regulations of the Department of... OPERATIONS ENVIRONMENTAL QUALITY INCENTIVES PROGRAM Contracts and Payments § 1466.11 Technical services provided by qualified personnel not affiliated with USDA. (a) NRCS may use the services of qualified TSPs...

  1. Dietary habits of obese patients qualified for bariatric procedures.

    Science.gov (United States)

    Jastrzebska-Mierzyńska, Marta; Ostrowska, Lucyna; Hady, Hady Razak; Dadan, Jacek

    2014-01-01

    Patients with obesity, including morbid obesity, commit numerous dietary mistakes. They prefer high-energy diets, but of poor nutritional value. Patients qualified for bariatric procedures show deficiencies in vitamins and minerals due to insufficient intake of vegetables, fruit and whole grain products. Analysis of dietary habits in morbidly obese patients prepared for bariatric surgery, including assessment of eating style and frequency of consumption of certain products. The study group contained 39 people aged 18 - 65 years, who were surveyed with a questionnaire elaborated in the Department of Clinical Dietetics and Nutrition, Medical University of Bialystok. The following factors were assessed: number of meals, snacking between meals and eating at night, types of snacks eaten, and frequency of consumption of certain foods. Results were analyzed using Statistica 9.0. The majority of surveyed men (41.7%) ate three meals a day, whereas most women (40.7%) had at least 4 meals a day. Nearly 85% of the respondents admitted snacking between meals, mainly eating fruit, sweets and sandwiches. Whole grain cereal, milk and dairy products, fish, fruit, vegetables and pulses appeared in diet of patients qualified for treatment of obesity very rarely. Dietary habits of obese patients qualified for bariatric procedures are not consistent with recommendations. Therefore, these patients should receive nutritional education in order to foster proper eating habits that will help in the postoperative nutrition.

  2. Experience in initial training required for the recognition of the qualified RP expert in Spain

    International Nuclear Information System (INIS)

    Rodriguez Suarez, M.; Marco Arboli, M.; Menarguez, J.

    2003-01-01

    An important point of the actions inside the European framework to achieve the harmonisation of the training programmes and recognition was included in the European directive 96/29/Euratom which includes definition and specific tasks of the European Qualified Expert on Radiation Protection (RP). Basic syllabus for training of those experts was developed in the communication 98/C 133/03 concerning BSS applications. Although, in the Spanish education system, the training and recognition requirements of the high level qualified experts on RP was defined since 1977, until 2001, the figure of the Technical Qualified Expert on RP does not appear in the legal framework. In December 2002, a new regulation of the Spanish Regulatory Body, CSN, about qualifications to obtain the recognition of RP Expert in Spain (both high qualified and technical RP experts) was published. Concerning the qualified expert on RP, (RP Officer), responsible of the RP Service, which takes charge of the effective protection and advise radioactive and nuclear facilities in Rp aspects,has to be authorised by the regulatory body. to obtain the RP officer diploma, conceded by the CSN, an initial training of 300 hours and a three-year minimum experience are required (for X-ray installation a 6-month experience is enough). The technical qualified expert on RP is the worker who carried out the tasks in the a RP Service under the supervision of the RP officer. A Technician Qualified Expert on RP does not need an specific accreditation of the Regulatory Body, but an initial RP training and a three-month minimum experience are required and has hold a certificate by the RP officer. Continuous training is also required and as well has to receive a certificate from the RP officer. Since 1977, The Institute for energy Studies has been implementing specific training courses for those professionals who want to obtain the diploma of RP officer (high degree qualified RP expert), conceded by the CSN. Since then

  3. 26 CFR 1.221-1 - Deduction for interest paid on qualified education loans after December 31, 2001.

    Science.gov (United States)

    2010-04-01

    ... Individuals § 1.221-1 Deduction for interest paid on qualified education loans after December 31, 2001. (a) In... interest paid by the taxpayer during the taxable year on a qualified education loan. See paragraph (b)(4... paid on qualified education loans after December 31, 2001, in taxable years ending after December 31...

  4. Creating Highly Qualified Teachers: Maximizing University Resources to Provide Professional Development in Rural Areas

    Science.gov (United States)

    Mollenkopf, Dawn L.

    2009-01-01

    The "highly qualified teacher" requirement of No Child Left Behind has put pressure on rural school districts to recruit and retain highly qualified regular and special education teachers. If necessary, they may utilize uncertified, rural teachers with provisional certification; however, these teachers may find completing the necessary…

  5. 7 CFR 636.18 - Technical services provided by qualified personnel not affiliated with USDA.

    Science.gov (United States)

    2010-01-01

    ... HABITAT INCENTIVES PROGRAM § 636.18 Technical services provided by qualified personnel not affiliated with... affiliated with USDA. 636.18 Section 636.18 Agriculture Regulations of the Department of Agriculture... provided by qualified personnel not affiliated with USDA may include, but is not limited to: Conservation...

  6. Comparative study on sintered alumina for ballistic shielding application

    International Nuclear Information System (INIS)

    Melo, Francisco Cristovao Lourenco de; Goncalves, Diniz Pereira

    1997-01-01

    This work presents a development of the armor made from special ceramic materials and kevlar. An experimental investigation was conducted to study the ballistic penetration resistance on three samples taken from sintered alumina: a commercial one and two formulations A and B made in IAE/CTA. The main differences between the two formulations was the grain size and bend resistance. The knowledge of the mechanisms during the penetration and perforation process allowed to apply a ductile composite laminate made form kevlar under the alumina to delay its rupture. The last ballistic test showed how a Weibull's modulii and other mechanical properties are able to improve ballistic penetration resistance. (author)

  7. Validation of mentorship model for newly qualified professional ...

    African Journals Online (AJOL)

    Newly qualified professional nurses (NQPNs) allocated to community health care services require the use of validated model to practice independently. Validation was done to adapt and assess if the model is understood and could be implemented by NQPNs and mentors employed in community health care services.

  8. 12 CFR 617.7125 - How should a qualified lender determine the effective interest rate?

    Science.gov (United States)

    2010-01-01

    ... effective interest rate? 617.7125 Section 617.7125 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM BORROWER RIGHTS Disclosure of Effective Interest Rates § 617.7125 How should a qualified lender determine the effective interest rate? (a) A qualified lender must calculate the effective interest rate on...

  9. 12 CFR 574.8 - Qualified stock issuances by undercapitalized savings associations or holding companies.

    Science.gov (United States)

    2010-01-01

    ... voting stock of the issuing undercapitalized savings association or savings and loan holding company. (8... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Qualified stock issuances by undercapitalized... SUPERVISION, DEPARTMENT OF THE TREASURY ACQUISITION OF CONTROL OF SAVINGS ASSOCIATIONS § 574.8 Qualified stock...

  10. Exploring selection and recruitment processes for newly qualified nurses: a sequential-explanatory mixed-method study.

    Science.gov (United States)

    Newton, Paul; Chandler, Val; Morris-Thomson, Trish; Sayer, Jane; Burke, Linda

    2015-01-01

    To map current selection and recruitment processes for newly qualified nurses and to explore the advantages and limitations of current selection and recruitment processes. The need to improve current selection and recruitment practices for newly qualified nurses is highlighted in health policy internationally. A cross-sectional, sequential-explanatory mixed-method design with 4 components: (1) Literature review of selection and recruitment of newly qualified nurses; and (2) Literature review of a public sector professions' selection and recruitment processes; (3) Survey mapping existing selection and recruitment processes for newly qualified nurses; and (4) Qualitative study about recruiters' selection and recruitment processes. Literature searches on the selection and recruitment of newly qualified candidates in teaching and nursing (2005-2013) were conducted. Cross-sectional, mixed-method data were collected from thirty-one (n = 31) individuals in health providers in London who had responsibility for the selection and recruitment of newly qualified nurses using a survey instrument. Of these providers who took part, six (n = 6) purposively selected to be interviewed qualitatively. Issues of supply and demand in the workforce, rather than selection and recruitment tools, predominated in the literature reviews. Examples of tools to measure values, attitudes and skills were found in the nursing literature. The mapping exercise found that providers used many selection and recruitment tools, some providers combined tools to streamline process and assure quality of candidates. Most providers had processes which addressed the issue of quality in the selection and recruitment of newly qualified nurses. The 'assessment centre model', which providers were adopting, allowed for multiple levels of assessment and streamlined recruitment. There is a need to validate the efficacy of the selection tools. © 2014 John Wiley & Sons Ltd.

  11. Damage characterization of E-glass and C-glass fibre polymer composites after high velocity impact

    Science.gov (United States)

    Razali, N.; Sultan, M. T. H.; Cardona, F.; Jawaid, M.

    2017-12-01

    The purpose of this work is to identify impact damage on glass fibre reinforced polymer composite structures after high velocity impact. In this research, Type C-glass (600 g/m2) and Type E-glass (600 g/m2) were used to fabricate Glass Fibre-Reinforced Polymer composites (GFRP) plates. The panels were fabricated using a vacuum bagging and hot bounder method. Single stage gas gun (SSGG) was used to do the testing and data acquisition system was used to collect the damage data. Different types of bullets and different pressure levels were used for the experiment. The obtained results showed that the C-glass type of GFRP experienced more damage in comparison to E-glass type of materials based on the amount of energy absorbed on impact and the size of the damage area. All specimens underwent a partial fibre breakage but the laminates were not fully penetrated by the bullets. This indicated that both types of materials have high impact resistance even though the applied pressures of the gas gun were on the high range. We concluded that within the material specifications of the laminates including the type of glass fibre reinforcement and the thickness of the panels, those composite materials are safe to be applied in structural and body armour applications as an alternative to more expensive materials such as Kevlar and type S-glass fibre based panels.

  12. TopWorx/GO switch new generation nuclear qualified proximity position sensors

    International Nuclear Information System (INIS)

    Merrifield, G.

    2011-01-01

    An overview of the benefits of installing TopWorx/GO Nuclear Qualified Proximity Position Sensors instead of traditional mechanical switches. Mechanical switches have been the standard for the nuclear industry for years, but that is only because of lack of competition. Because of multiple moving parts, three-piece design, and new low current control systems, mechanical switches are susceptible to a host of environmental factors that cause them to break and/or fail. TopWorx/GO Switch is a smaller, rugged, dependable, one-piece Stainless Steel proximity position sensor that that exceeds CANDU and Global Qualification Levels, easily replacing mechanical switches. It is the only position sensor to meet or exceed Westinghouse AP 1000 specifications as well. Nuclear facilities save money in maintenance reductions, extended PM's and reduction in 'Man REM' hours. This is achieved by not having to service and replace GO Switch position sensors as often as mechanical switches, since their qualified life is 100 years +1 Post Accident submerged. Plant safety is increased due to less switch failure, higher qualification testing levels, repeatability and longer qualified life. (author)

  13. 42 CFR 416.26 - Qualifying for an agreement.

    Science.gov (United States)

    2010-10-01

    ..., where State law requires licensure, the ASC complies with State licensure requirements; and (3) The ASC.... (c) Acceptance of the ASC as qualified to furnish ambulatory surgical services. If CMS determines... its authorized representative; and (2) File them with CMS. (e) Acceptance by CMS. If CMS accepts the...

  14. 26 CFR 1.465-27 - Qualified nonrecourse financing.

    Science.gov (United States)

    2010-04-01

    ... partnership; incidental property. (i) X is a limited liability company that is classified as a partnership for.... (i) UTP1 and UTP2, both limited liability companies classified as partnerships, are the only general... as qualified nonrecourse financing. (4) Partnership liability. For purposes of section 465(b)(6) and...

  15. 30 CFR 75.153 - Electrical work; qualified person.

    Science.gov (United States)

    2010-07-01

    ... Mine Safety and Health Districts at regular intervals, or as demand requires. (d) A score of at least... Section 75.153 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Qualified and Certified Persons § 75...

  16. 26 CFR 1.414(r)-1 - Requirements applicable to qualified separate lines of business.

    Science.gov (United States)

    2010-04-01

    ... lines of business. 1.414(r)-1 Section 1.414(r)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT... Plans, Etc. § 1.414(r)-1 Requirements applicable to qualified separate lines of business. (a) In general. Section 414(r) prescribes the conditions under which an employer is treated as operating qualified...

  17. A Theoretical Investigation of Composite Overwrapped Pressure Vessel (COPV) Mechanics Applied to NASA Full Scale Tests

    Science.gov (United States)

    Thesken, John C.; Murthy, Pappu L. N.; Phoenix, S. L.; Greene, N.; Palko, Joseph L.; Eldridge, Jeffrey; Sutter, James; Saulsberry, R.; Beeson, H.

    2009-01-01

    A theoretical investigation of the factors controlling the stress rupture life of the National Aeronautics and Space Administration's (NASA) composite overwrapped pressure vessels (COPVs) continues. Kevlar (DuPont) fiber overwrapped tanks are of particular concern due to their long usage and the poorly understood stress rupture process in Kevlar filaments. Existing long term data show that the rupture process is a function of stress, temperature and time. However due to the presence of a load sharing liner, the manufacturing induced residual stresses and the complex mechanical response, the state of actual fiber stress in flight hardware and test articles is not clearly known. This paper is a companion to a previously reported experimental investigation and develops a theoretical framework necessary to design full-scale pathfinder experiments and accurately interpret the experimentally observed deformation and failure mechanisms leading up to static burst in COPVs. The fundamental mechanical response of COPVs is described using linear elasticity and thin shell theory and discussed in comparison to existing experimental observations. These comparisons reveal discrepancies between physical data and the current analytical results and suggest that the vessel s residual stress state and the spatial stress distribution as a function of pressure may be completely different from predictions based upon existing linear elastic analyses. The 3D elasticity of transversely isotropic spherical shells demonstrates that an overly compliant transverse stiffness relative to membrane stiffness can account for some of this by shifting a thin shell problem well into the realm of thick shell response. The use of calibration procedures are demonstrated as calibrated thin shell model results and finite element results are shown to be in good agreement with the experimental results. The successes reported here have lead to continuing work with full scale testing of larger NASA COPV

  18. 36 CFR 908.13 - Rights of Qualified Persons.

    Science.gov (United States)

    2010-07-01

    ... POLICY AND PROCEDURES TO FACILITATE THE RETENTION OF DISPLACED BUSINESSES AND RESIDENTS IN THE... leasing plan which are, in the Corporation's opinion, major. (c) Each Qualified Person on the List, who is... opportunity to occupy Newly Developed Space shall not be limited to the square on which its previous location...

  19. 22 CFR 19.6-2 - Qualifying court order.

    Science.gov (United States)

    2010-04-01

    ... principal's Foreign Service retirement benefit or survivor benefit. If a court directs or implies that a... Foreign Relations DEPARTMENT OF STATE PERSONNEL BENEFITS FOR SPOUSES AND FORMER SPOUSES OF PARTICIPANTS IN... the Secretary of State. A qualifying court order must— (1) Be consistent with the terms of the Act and...

  20. 26 CFR 54.4980B-3 - Qualified beneficiaries.

    Science.gov (United States)

    2010-04-01

    ... the day before the qualifying event (that is, the divorce or death) will have been by reason of D's... event, and the reason for the individual's lack of actual coverage (such as the individual's having..., the individual is covered under the group health plan by reason of another individual's election of...

  1. Multiparameter structural optimization of single-walled carbon nanotube composites: toward record strength, stiffness, and toughness.

    Science.gov (United States)

    Shim, Bong Sup; Zhu, Jian; Jan, Edward; Critchley, Kevin; Ho, Szushen; Podsiadlo, Paul; Sun, Kai; Kotov, Nicholas A

    2009-07-28

    Efficient coupling of mechanical properties of SWNTs with the matrix leading to the transfer of unique mechanical properties of SWNTs to the macroscopic composites is a tremendous challenge of today's materials science. The typical mechanical properties of known SWNT composites, such as strength, stiffness, and toughness, are assessed in an introductory survey where we focused on concrete numerical parameters characterizing mechanical properties. Obtaining ideal stress transfer will require fine optimization of nanotube-polymer interface. SWNT nanocomposites were made here by layer-by-layer (LBL) assembly with poly(vinyl alcohol) (PVA), and the first example of optimization in respect to key parameters determining the connectivity at the graphene-polymer interface, namely, degree of SWNT oxidation and cross-linking chemistry, was demonstrated. The resulting SWNT-PVA composites demonstrated tensile strength (σ(ult)) = 504.5 ± 67.3 MPa, stiffness (E) = 15.6 ± 3.8 GPa, and toughness (K) = 121.2 ± 19.2 J/g with maximum values recorded at σ(ult) = 600.1 MPa, E = 20.6 GPa, and K = 152.1 J/g. This represents the strongest and stiffest nonfibrous SWNT composites made to date outperforming other bulk composites by 2-10 times. Its high performance is attributed to both high nanotube content and efficient stress transfer. The resulting LBL composite is also one of the toughest in this category of materials and exceeding the toughness of Kevlar by 3-fold. Our observation suggests that the strengthening and toughening mechanism originates from the synergistic combination of high degree of SWNT exfoliation, efficient SWNT-PVA binding, crack surface roughening, and fairly efficient distribution of local stress over the SWNT network. The need for a multiscale approach in designing SWNT composites is advocated.

  2. 49 CFR 604.15 - Registration of qualified human service organizations.

    Science.gov (United States)

    2010-10-01

    ... low income, advanced age, or with disabilities), shall register on FTA's charter registration Web site... service organization and whether the qualified human service organization is exempt from taxation under...

  3. 77 FR 26175 - Section 42 Qualified Contract Provisions

    Science.gov (United States)

    2012-05-03

    ... indebtedness under general principles of Federal income tax law, and (3) upon the sale of the building, are... building for sale to the general public at the determined qualified contract price upon receipt of a... because of variations under State laws concerning the terms of a bona fide contract and methods for...

  4. 26 CFR 1.41-2 - Qualified research expenses.

    Science.gov (United States)

    2010-04-01

    ... Credits Against Tax § 1.41-2 Qualified research expenses. (a) Trade or business requirement—(1) In general... research and experimental expenses) are not necessarily paid or incurred in carrying on a trade or business for purposes of section 41. A research expense must relate to a particular trade or business being...

  5. 78 FR 61987 - Corbett Water District; Notice of Preliminary Determination of a Qualifying Conduit Hydropower...

    Science.gov (United States)

    2013-10-09

    ... District; Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and Soliciting... construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower Regulatory Efficiency Act of 2013 (HREA). The Corbett Hydroelectric...

  6. Composites Materials and Manufacturing Technologies for Space Applications

    Science.gov (United States)

    Vickers, J. H.; Tate, L. C.; Gaddis, S. W.; Neal, R. E.

    2016-01-01

    Composite materials offer significant advantages in space applications. Weight reduction is imperative for deep space systems. However, the pathway to deployment of composites alternatives is problematic. Improvements in the materials and processes are needed, and extensive testing is required to validate the performance, qualify the materials and processes, and certify components. Addressing these challenges could lead to the confident adoption of composites in space applications and provide spin-off technical capabilities for the aerospace and other industries. To address the issues associated with composites applications in space systems, NASA sponsored a Technical Interchange Meeting (TIM) entitled, "Composites Materials and Manufacturing Technologies for Space Applications," the proceedings of which are summarized in this Conference Publication. The NASA Space Technology Mission Directorate and the Game Changing Program chartered the meeting. The meeting was hosted by the National Center for Advanced Manufacturing (NCAM)-a public/private partnership between NASA, the State of Louisiana, Louisiana State University, industry, and academia, in association with the American Composites Manufacturers Association. The Louisiana Center for Manufacturing Sciences served as the coordinator for the TIM.

  7. A facile synthetic route to poly(p-phenylene terephthalamide) with dual functional groups.

    Science.gov (United States)

    Du, Shuming; Wang, Wenbin; Yan, Yan; Zhang, Jie; Tian, Ming; Zhang, Liqun; Wan, Xinhua

    2014-09-07

    Claisen rearrangement reaction was employed for the first time to obtain a novel PPTA bearing reactive allyl and hydroxyl groups which may act as a sizing agent of Kevlar fibers to improve the interface structure and interfacial adhesion of rubber or epoxy based composites.

  8. Proceedings of the 19th international SAMPE technical conference. Volume 19

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    These proceedings collect papers on materials science. Topics include: the microstructure of Al-Li-Mg-Cu-Zr alloys, ultrasonic crack detection in composites, bending behavior of kevlar/epoxy beams, solid solution single crystals, polyamide-imides, and the growth of mercuric iodide in Spacelab III

  9. 26 CFR 1.414(r)-7 - Determination of the employees of an employer's qualified separate lines of business.

    Science.gov (United States)

    2010-04-01

    ... same department, or at the same location, to the same qualified separate line of business would be an... qualified separate lines of business. 1.414(r)-7 Section 1.414(r)-7 Internal Revenue INTERNAL REVENUE...-Sharing, Stock Bonus Plans, Etc. § 1.414(r)-7 Determination of the employees of an employer's qualified...

  10. Continuous composite riser

    Energy Technology Data Exchange (ETDEWEB)

    Slagsvold, L. [ABB Offshore Systems (Norway)

    2002-12-01

    The industry is now looking at developing reserves in waters depths of up to 3000 m (10000 ft). When moving into deeper waters the un-bonded flexible riser becomes very heavy and introduces large hang-off forces on the vessel. We are therefore investigating riser concepts incorporating new materials and with a simpler cross section that can be used for floating production. Advanced composite materials have properties such as, low weight, high strength, good durability and very good fatigue performance. Composite materials are slowly being exploited in the oil industry; they are being prototype tested for drilling risers and small diameter lines. Part of the process for the industry to accept larger diameter production risers made out of composite materials is to understand both the advantages and limitations. A new continuous composite riser system is being developed which capitalizes on the technical benefits of this material while addressing the known constraints. The fully bonded riser is being developed for ultra deep waters and its' characteristics include high temperature (160 deg C), high pressure (500 barg min), light weight, chemical resistant, good insulation, excellent fatigue characteristics and installation by reeling. The concept is based on the use of a thermoplastic liner together with a thermoplastic carbon fibre composite. This paper summarises the ongoing development, which has a goal to manufacture and qualify an 8'' riser, and includes all the steps in a production process from material qualification to the winding process and analytical modelling. (author)

  11. Effect of temperature on composite sandwich structures subjected to low velocity impact. [aircraft construction materials

    Science.gov (United States)

    Sharma, A. V.

    1980-01-01

    The effect of low velocity projectile impact on sandwich-type structural components was investigated. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, the dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failure in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension-and compression-loaded laminates. The specific-strengths and -modulii for the various laminates tested are also given.

  12. 77 FR 76941 - Defense Federal Acquisition Regulation Supplement: New Qualifying Country-Poland (DFARS Case 2012...

    Science.gov (United States)

    2012-12-31

    ... discriminatory barriers to procurements of supplies and services produced by industrial enterprises of the other....003 is amended in paragraph (10), the definition of ``qualifying country'' by adding in alphabetical... place; 0 b. In paragraph (a), the definition of ``qualifying country'', by adding, in alphabetical order...

  13. 78 FR 63176 - Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and Soliciting...

    Science.gov (United States)

    2013-10-23

    ... Preliminary Determination of a Qualifying Conduit Hydropower Facility and Soliciting Comments and Motions To... of intent to construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower Regulatory Efficiency Act of 2013 (HREA). The...

  14. ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

    International Nuclear Information System (INIS)

    Stillo, Andrew; Ricketts, Craig I.

    2013-01-01

    High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

  15. ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

    Energy Technology Data Exchange (ETDEWEB)

    Stillo, Andrew [Camfil Farr, 1 North Corporate Drive, Riverdale, NJ 07457 (United States); Ricketts, Craig I. [New Mexico State University, Department of Engineering Technology and Surveying Engineering, P.O. Box 30001 MSC 3566, Las Cruces, NM 88003-8001 (United States)

    2013-07-01

    High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

  16. The effect of qualifying language on perceptions of drug appeal, drug experience, and estimates of side-effect incidence in DTC advertising.

    Science.gov (United States)

    Davis, Joel

    2007-01-01

    This study examined how the use of qualifying language in direct-to-consumer (DTC) pharmaceutical advertising affects consumers' perceptions of drug appeal, anticipated pleasantness of drug usage, and the expected incidence of side-effect occurrence. A sample of 669 individuals participated in a 2 x 8 complete factorial design. The design manipulated the number of side effects associated with drug use and the type of qualifying language used to describe the side effects. The eight experimental qualifying language cells represented one control condition (no qualifying language), three cells where each of three types of qualifying language were presented individually, and four cells where qualifying language was combined. The results indicate that qualifying language has a profound effect on drug perceptions, especially when used in combination. Drug appeal and the anticipated drug-using experience almost always were more positive in the presence of qualifying language. Qualifying language appears to exert its influence by causing individuals to reduce their estimate of the likelihood of experiencing individual side effects. Policy implications of the research, particularly for evaluation of "fair balance" and the reporting of side effects, are presented.

  17. 34 CFR 300.18 - Highly qualified special education teachers.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 2 2010-07-01 2010-07-01 false Highly qualified special education teachers. 300.18... SPECIAL EDUCATION AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION ASSISTANCE TO STATES FOR THE... special education teachers. (a) Requirements for special education teachers teaching core academic...

  18. Towards Qualifiable Code Generation from a Clocked Synchronous Subset of Modelica

    Directory of Open Access Journals (Sweden)

    Bernhard Thiele

    2015-01-01

    Full Text Available So far no qualifiable automatic code generators (ACGs are available for Modelica. Hence, digital control applications can be modeled and simulated in Modelica, but require tedious additional efforts (e.g., manual reprogramming to produce qualifiable target system production code. In order to more fully leverage the potential of a model-based development (MBD process in Modelica, a qualifiable automatic code generator is needed. Typical Modelica code generation is a fairly complex process which imposes a huge development burden to any efforts of tool qualification. This work aims at mapping a Modelica subset for digital control function development to a well-understood synchronous data-flow kernel language. This kernel language allows to resort to established compilation techniques for data-flow languages which are understood enough to be accepted by certification authorities. The mapping is established by providing a translational semantics from the Modelica subset to the synchronous data-flow kernel language. However, this translation turned out to be more intricate than initially expected and has given rise to several interesting issues that require suitable design decisions regarding the mapping and the language subset.

  19. Registration of qualified radiation protection experts in the Netherlands

    International Nuclear Information System (INIS)

    Abrahamse, J.C.; Kops, J.A.M.M.; Vermeulen, A.M.T.I.; Zuur, C.

    2002-01-01

    In Euratom Directive 96/29 (1) the Euratom Basic Safety Standards are given. The member states of the EC have to implement this directive in their national legislation. In the Netherlands this is done in the new radiation protection legislation (Radiation Protection Decree 2002 (2)), which came into force in the first half of 2002. In this new regulation is stated that radiological activities must be done by or under supervision of a qualified radiation protection expert. With respect to the qualified expert is stated that: the qualified expert must be registered in a notified registration system; rules will be formulated with respect to the demanded qualification levels of the experts. These demands can be different for different tasks rules will be formulated for the notification of the register, the way to become registered, the costs and so on. Mid 2001 a project is started to prepare the registration system. Information was gained from and discussions took place with the important parties on the radiological playing field in the Netherlands (employers, organisations of experts and education institutes). Furthermore information is obtained from certification institutes. It was decided to accept as starting point the education levels obtained from the radiation protection education institutes, which are approved at the moment. At a later phase will be evaluated whether this system needs to be changed. In section 2 of this paper the radiation protection system in the Netherlands will be discussed in more detail. Section 2 deals with the target group and in section 3 the outlines of the registration system to be developed are discussed

  20. Comparative study on sintered alumina for ballistic shielding application; Estudo comparativo entre aluminas sinterizadas visando aplicacao em blindagem balistica

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Francisco Cristovao Lourenco de; Goncalves, Diniz Pereira [Centro Tecnico Aeroespacial (CTA), Sao Jose dos Campos, SP (Brazil). Inst. de Aeronautica e Espaco

    1997-12-31

    This work presents a development of the armor made from special ceramic materials and kevlar. An experimental investigation was conducted to study the ballistic penetration resistance on three samples taken from sintered alumina: a commercial one and two formulations A and B made in IAE/CTA. The main differences between the two formulations was the grain size and bend resistance. The knowledge of the mechanisms during the penetration and perforation process allowed to apply a ductile composite laminate made form kevlar under the alumina to delay its rupture. The last ballistic test showed how a Weibull`s modulii and other mechanical properties are able to improve ballistic penetration resistance. (author) 3 refs.

  1. Moisture sorption and thermal characteristics of polyaramide blend fabrics

    OpenAIRE

    Genç, Gözde; Alp, Burcu; Balköse, Devrim; Ülkü, Semra; Cireli, Aysun

    2006-01-01

    Four types of fabrics woven from various polyaramid fibers of Nomex and Kevlar blends were characterized by morphology, XRD, elemental analysis, thermal analysis, and moisture adsorption isotherms. The blends consisted of Polybenzimidazole/ Kevlar blend (40% FBI and 60% Kevlar®), Nomex Delta A (blend of 60% Kevlar and 40% Nomex®), Nomex Delta T (blend of 75% Nomex, 23% Kevlar, and 2% P140 antistatic fiber), and Nomex III (fabric with a 95/5 blend of Nomex and Kevlar) containing 1% steel fiber...

  2. 78 FR 62350 - FFP Qualified Hydro 14, LLC; Western Minnesota Municipal Power Agency; Notice Announcing...

    Science.gov (United States)

    2013-10-18

    .... 14491-000] FFP Qualified Hydro 14, LLC; Western Minnesota Municipal Power Agency; Notice Announcing... applications were filed by FFP Qualified Hydro 14, LLC for Project No. 13579-002 and Western Minnesota... regular business day. See 18 CFR 385.2001(a)(2) (2013). On October 21, 2013, at 10:00 a.m. (Eastern Time...

  3. 12 CFR 617.7130 - What initial disclosures must a qualified lender make to a borrower?

    Science.gov (United States)

    2010-01-01

    ... lender make to a borrower? 617.7130 Section 617.7130 Banks and Banking FARM CREDIT ADMINISTRATION FARM... must a qualified lender make to a borrower? (a) Required disclosures—in general. A qualified lender... certificates that borrowers are required to purchase are at risk and may only be retired at the discretion of...

  4. Qualified expert training: the ERPC (European Radiation Protection Course)

    International Nuclear Information System (INIS)

    Deboodt, P.; Bourguignon, M.; Juhel, T.; Lirsac, N.; Luciani, A.; Marco, M.; Schmitt-Hanning, A. M.; Van der Steen, J.

    2003-01-01

    Since 2000, a training for the qualified experts is organised by several European partners in France at Saclay near Pais. The objective of this training is to deliver the theoretical knowledge needed to be recognised as a qualified expert in radiation protection according to the European requirements. The training delivered in English, includes four independent modules; basics, occupational exposure in nuclear and industrial applications, medical exposures (patients and workers), radiation protection of the members of the public and the environment (4 or 5 weeks each). A written examination is organised at the end of each module. Lectures, practical works, exercises and visits are given by European lecturers. Students have the possibility to register in one or several module during one or several years. Participants could be students or professionals from all European countries satisfying the pre requite defined by the European board. A certificate validating the successfully passed modules will be delivered by the INSTN (National Institute of Nuclear Sciences and Technologies)

  5. Qualified expert training: the ERPC (European Radiation Protection Course)

    Energy Technology Data Exchange (ETDEWEB)

    Deboodt, P.; Bourguignon, M.; Juhel, T.; Lirsac, N.; Luciani, A.; Marco, M.; Schmitt-Hanning, A. M.; Van der Steen, J.

    2003-07-01

    Since 2000, a training for the qualified experts is organised by several European partners in France at Saclay near Pais. The objective of this training is to deliver the theoretical knowledge needed to be recognised as a qualified expert in radiation protection according to the European requirements. The training delivered in English, includes four independent modules; basics, occupational exposure in nuclear and industrial applications, medical exposures (patients and workers), radiation protection of the members of the public and the environment (4 or 5 weeks each). A written examination is organised at the end of each module. Lectures, practical works, exercises and visits are given by European lecturers. Students have the possibility to register in one or several module during one or several years. Participants could be students or professionals from all European countries satisfying the pre requite defined by the European board. A certificate validating the successfully passed modules will be delivered by the INSTN (National Institute of Nuclear Sciences and Technologies).

  6. 26 CFR 1.188-1 - Amortization of certain expenditures for qualified on-the-job training and child care facilities.

    Science.gov (United States)

    2010-04-01

    ... qualified on-the-job training and child care facilities. 1.188-1 Section 1.188-1 Internal Revenue INTERNAL... qualified on-the-job training and child care facilities. (a) Allowance of deduction—(1) In general. Under... operation of a qualified on-the-job training or child care facility or are integrally related facilities...

  7. Nursing educator perspectives of overseas qualified nurses' intercultural clinical communication: barriers, enablers and engagement strategies.

    Science.gov (United States)

    Philip, Susan; Manias, Elizabeth; Woodward-Kron, Robyn

    2015-09-01

    To understand the intercultural communication experiences and associated communication training needs of overseas qualified nurses in the Australian healthcare system from the unique perspectives of nurse educators teaching in accredited bridging programmes. Overseas qualified nurses are an integral part of the nursing workforce in migration destination countries. Communication training needs are more complex when there are cultural, ethnic and language differences between nurses, other health professionals and patients. A qualitative, exploratory research design using semi-structured interviews. All (nine) organisations involved in conducting the Australian Health Practitioner Regulation Agency approved preregistration bridging programmes for overseas qualified nurses within the state of Victoria, Australia, were involved in the study. Participants were 12 nurse educators employed in these organisations. Thematic analysis was undertaken. Three macro themes emerged about the overseas qualified nurses' intercultural communication: (1) pre-existing barriers and enablers to intercultural communication, for example, nurses' reluctance to engage in communicative strategies that build rapport with patients, (2) transitional behaviours and impact on communication, including maintenance of perceived cultural hierarchies between health professionals and (3) development of communicative competence, including expanding one's repertoire of conversational gambits. The findings point to the domains and causes of communication challenges facing overseas qualified nurses in new healthcare settings as well as strategies that the nurse educators and nurses can adopt. Communication cannot be merely regarded as a skill that can be taught in a didactic programme. Comprehensive understanding is needed about the sociocultural dimensions of these nurses' orientation, which can impact on how they communicate in their new healthcare settings. The findings can act as triggers for discussion

  8. Composite materials application on FORMOSAT-5 remote sensing instrument structure

    Directory of Open Access Journals (Sweden)

    Jen-Chueh Kuo

    2017-01-01

    Full Text Available Composite material has been widely applied in space vehicle structures due to its light weight and designed stiffness modulus. Some special mechanical properties that cannot be changed in general metal materials, such as low CTE (coefficient of thermal expansion and directional material stiffness can be artificially adjusted in composite materials to meet the user’s requirements. Space-qualified Carbon Fiber Reinforced Plastic (CFRP composite materials are applied In the FORMOSAT-5 Remote Sensing (RSI structure because of its light weight and low CTE characteristics. The RSI structural elements include the primary mirror supporting plate, secondary mirror supporting ring, and supporting frame. These elements are designed, manufactured, and verified using composite materials to meet specifications. The structure manufacturing process, detailed material properties, and CFRP structural element validation methods are introduced in this paper.

  9. Investigation on mechanical properties of basalt composite fabrics (experiment study)

    Science.gov (United States)

    Talebi Mazraehshahi, H.; Zamani, H.

    2010-06-01

    To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced and mechanical behaviors of this material investigated from view point of testing. For this study two type of fabric with different thickness used. Comparison between this composite reinforcement with popular reinforcement as carbon, glass, kevlar performed. To determine mechanical properties of epoxy based basalt fabric following test procedure performed : 1). Tensile testing according to ASTM D3039 in 0° and 90° direction to find ultimate strength in tension and shear, modulus of elasticity, elangation and ultimate strain. 2). Compression testing according to EN 2850 ultimate compression strength and maximum deformation under compression loading. 3). Shear testing according to ASTM D3518-94 to find in plane shear response of polymer matrix composites materials. 4). Predict flexural properties of sandwich construction which manufactured from basalt facing with PVC foam core according to ASTM C393-94. Material strength properties must be based on enough tests of material to meet the test procedure specifications [1]. For this reason six specimens were manufactured for testing and the tests were performed on them using an INSTRON machine model 5582. In the study, the effect of percent of resin in basalt reinforced composite was investigated. Also the weights of the ballast based composites with different percent of resin were measured with conventional composites. As the weight is an important parameter in aerospace industry when the designer wants to replace one material with

  10. Assessment of demand for and supply of qualified manpower for the nuclear industry

    International Nuclear Information System (INIS)

    Morelle, J.

    1993-01-01

    The OECD Nuclear Energy Agency recently published a study which presents the results of a pioneering survey of the demand for and the supply of qualified manpower in various sectors of the nuclear industry (including medicine), and in the related areas of regulation and education in 12 OECD countries. The current manpower situation is presented and the future demand is reviewed. Present and future activities of OECD countries to ensure a balance between supply and demand of qualified manpower are discussed

  11. 26 CFR 1.221-2 - Deduction for interest due and paid on qualified education loans before January 1, 2002.

    Science.gov (United States)

    2010-04-01

    ... Individuals § 1.221-2 Deduction for interest due and paid on qualified education loans before January 1, 2002... interest due and paid by the taxpayer during the taxable year on a qualified education loan. The deduction is allowed only with respect to interest due and paid on a qualified education loan during the first...

  12. Virginia Tech team qualifies as DARPA Urban Challenge semi-finalist

    OpenAIRE

    Crumbley, Liz

    2007-01-01

    "VictorTango," a team of Virginia Tech engineering and geography students, will travel to Victorville, Calif., for the national qualifying rounds of the Urban Challenge autonomous vehicle competition, sponsored by the Defense Advanced Research Projects Agency (DARPA).

  13. Aramid Nanofiber Composites for Energy Storage Applications

    Science.gov (United States)

    Tung, Siu on

    Lithium ion batteries and non-aqueous redox flow batteries represent two of the most important energy storage technologies to efficient electric vehicles and power grid, which are essential to decreasing U.S. dependence on fossil fuels and sustainable economic growth. Many of the developmental roadblocks for these batteries are related to the separator, an electrically insulating layer between the cathode and anode. Lithium dendrite growth has limited the performance and threatened the safety of lithium ion batteries by piercing the separator and causing internal shorts. In non-aqueous redox flow batteries, active material crossover through microporous separators and the general lack of a suitable ion conducting membrane has led to low operating efficiencies and rapid capacity fade. Developing new separators for these batteries involve the combination of different and sometimes seemingly contradictory properties, such as high ionic conductivity, mechanical stability, thermal stability, chemical stability, and selective permeability. In this dissertation, I present work on composites made from Kevlar-drived aramid nanofibers (ANF) through rational design and fabrication techniques. For lithium ion batteries, a dendrite suppressing layer-by-layer composite of ANF and polyethylene oxide is present with goals of high ionic conductivity, improved safety and thermal stability. For non-aqueous redox flow batteries, a nanoporous ANF separator with surface polyelectrolyte modification is used to achieve high coulombic efficiencies and cycle life in practical flow cells. Finally, manufacturability of ANF based separators is addressed through a prototype machine for continuous ANF separator production and a novel separator coated on anode assembly. In combination, these studies serve as a foundation for addressing the challenges in separator engineering for lithium ion batteries and redox flow batteries.

  14. Spatial factors as contextual qualifiers of information seeking

    Directory of Open Access Journals (Sweden)

    R. Savolainen

    2006-01-01

    Full Text Available Introduction. This paper investigates the ways in which spatial factors have been approached in information seeking studies. The main attention was focused on studies discussing information seeking on the level of source selection and use. Method. Conceptual analysis of about 100 articles and books thematizing spatial issues of information seeking. Due to research economy, the main attention was paid to studies on everyday life information seeking. Results. Three major viewpoints were identified with regard to the degree of objectivity of spatial factors. The objectifying approach conceives of spatial factors as external and entity-like qualifiers that primarly constrain information seeking. The realistic-pragmatic approach emphasizes the ways in which the availabilty of information sources in different places such as daily work environments orient information seeking. The perspectivist approach focuses on how people subjectively assess the significance of various sources by means of spatial constructs such as information horizons. Conclusion. Spatial factors are centrally important contextual qualifiers of information seeking. There is a need to further explore the potential of the above viewpoints by relating the spatial and temporal factors of information seeking.

  15. 78 FR 66355 - Pleasant Grove City, UT; Notice of Preliminary Determination of a Qualifying Conduit Hydropower...

    Science.gov (United States)

    2013-11-05

    ... City, UT; Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and... Grove City, Utah (Pleasant Grove) filed a notice of intent to construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower...

  16. 78 FR 53752 - City of Sandpoint, Idaho; Notice of Preliminary Determination of a Qualifying Conduit Hydropower...

    Science.gov (United States)

    2013-08-30

    ... Sandpoint, Idaho; Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and... intent to construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower Regulatory Efficiency Act of 2013 (HREA). The Little...

  17. 78 FR 61985 - City of Astoria, Oregon; Notice of Preliminary Determination of a Qualifying Conduit Hydropower...

    Science.gov (United States)

    2013-10-09

    ..., Oregon; Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and Soliciting... of intent to construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower Regulatory Efficiency Act of 2013 (HREA). The...

  18. Using neutrosophic graph cut segmentation algorithm for qualified rendering image selection in thyroid elastography video.

    Science.gov (United States)

    Guo, Yanhui; Jiang, Shuang-Quan; Sun, Baiqing; Siuly, Siuly; Şengür, Abdulkadir; Tian, Jia-Wei

    2017-12-01

    Recently, elastography has become very popular in clinical investigation for thyroid cancer detection and diagnosis. In elastogram, the stress results of the thyroid are displayed using pseudo colors. Due to variation of the rendering results in different frames, it is difficult for radiologists to manually select the qualified frame image quickly and efficiently. The purpose of this study is to find the qualified rendering result in the thyroid elastogram. This paper employs an efficient thyroid ultrasound image segmentation algorithm based on neutrosophic graph cut to find the qualified rendering images. Firstly, a thyroid ultrasound image is mapped into neutrosophic set, and an indeterminacy filter is constructed to reduce the indeterminacy of the spatial and intensity information in the image. A graph is defined on the image and the weight for each pixel is represented using the value after indeterminacy filtering. The segmentation results are obtained using a maximum-flow algorithm on the graph. Then the anatomic structure is identified in thyroid ultrasound image. Finally the rendering colors on these anatomic regions are extracted and validated to find the frames which satisfy the selection criteria. To test the performance of the proposed method, a thyroid elastogram dataset is built and totally 33 cases were collected. An experienced radiologist manually evaluates the selection results of the proposed method. Experimental results demonstrate that the proposed method finds the qualified rendering frame with 100% accuracy. The proposed scheme assists the radiologists to diagnose the thyroid diseases using the qualified rendering images.

  19. 9 CFR 77.36 - Interstate movement from qualified herds.

    Science.gov (United States)

    2010-01-01

    ... date of movement. If a group of captive cervids from a qualified herd is being moved interstate... unclassified herd. (4) Captive cervids being moved interstate for the purpose of exhibition only may be moved... being moved directly from a classified herd, the captive cervid must be isolated from all other animals...

  20. 24 CFR 266.100 - Qualified housing finance agency (HFA).

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Qualified housing finance agency (HFA). 266.100 Section 266.100 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT MORTGAGE...

  1. The usage of optical fibers for damage detection in ballistic protection composite laminates

    Directory of Open Access Journals (Sweden)

    Živković Irena D.

    2006-01-01

    Full Text Available This paper describes the procedure of embedding fiber optic sensors in laminar thermoplastic composite material, as well as damage investigation after ballistic loading. Thermoplastic-reinforced composite materials were made for increased material damage resistance during ballistic loading. Damage inside the composite material was detected by observing the intensity drop of the light signal transmitted through the optical fibers. Experimental testing was carried out in order to observe and analyze the response of the material under various load conditions. Different types of Kevlar reinforced composite materials (thermoplastic, thermo reactive and thermoplastic with ceramic plate as the impact face were made. Material damage resistance during ballistic loading was investigated and compared. Specimens were tested under multiple load conditions. The opto-electronic part of the measurement system consists of two light-emitting diodes as light sources for the optical fibers, and two photo detectors for the light intensity measurement. The output signal was acquired from photo detectors by means of a data acquisition board and personal computer. The measurements showed an intensity drop of the transmitted light signal as a result of the applied loading on composite structure for all the optical fibers. All the diagrams show similar behavior of the light signal intensity. In fact, all of them may be divided into three zones: the zone of penetration of the first composite layer, the bullet traveling zone through the composite material till its final stop, and the material relaxation zone. The attenuation of the light signal intensity during impact is caused by the influence of the applied dynamic stress on the embedded optical fibers. The applied stress caused micro bending of the optical fiber, changes in the shape of the cross-section and the unequal changes of the indices of refraction of the core and cladding due to the stress-optic effect. The

  2. 12 CFR 617.7315 - What records must the qualified lender maintain on behalf of the CRC?

    Science.gov (United States)

    2010-01-01

    ... on behalf of the CRC? 617.7315 Section 617.7315 Banks and Banking FARM CREDIT ADMINISTRATION FARM... must the qualified lender maintain on behalf of the CRC? A qualified lender must maintain a complete file of all requests for CRC reviews, including participation in state mediation programs, the minutes...

  3. 78 FR 56872 - City of Barre, Vermont; Notice of Preliminary Determination of a Qualifying Conduit Hydropower...

    Science.gov (United States)

    2013-09-16

    ..., Vermont; Notice of Preliminary Determination of a Qualifying Conduit Hydropower Facility and Soliciting... construct a qualifying conduit hydropower facility, pursuant to section 30 of the Federal Power Act, as amended by section 4 of the Hydropower Regulatory Efficiency Act of 2013 (HREA). The Nelson Street 17 kW...

  4. A longitudinal, mixed methods investigation of newly qualified nurses' workplace stressors and stress experiences during transition.

    Science.gov (United States)

    Halpin, Yvonne; Terry, Louise M; Curzio, Joan

    2017-11-01

    To investigate transition in newly qualified nurses through an exploration of their stressors and stress experiences during their first 12 months postqualifying. Globally, thousands of new nurses qualify annually. They are crucial for the profession and healthcare service delivery. Work-related stress has multiple serious consequences, yet there is a lack of robust, empirical evidence that directly analyses newly qualified nurses and the stress they feel and experience in the workplace. Understanding what causes newly qualified nurses' stress is vital to retaining and nurturing this vital component of the workforce. Longitudinal, explanatory sequential mixed methods, cohort study. At the point of qualification (n = 288), 6 months postqualifying (n = 107) and 12 months postqualifying (n = 86), newly qualified nurses completed the Nursing Stress Scale, with 14 completing a one-to-one interview at 12 months postqualifying. Data were collected from 2010 - 2012. Inferential statistics, "thematic analysis" and "side-by-side comparisons in a discussion" were used for analysis. Workload was consistently the highest reported stressor with inadequate staffing and managing multiple role demands given as explanations. Incivility within the workplace was a noted stressor. Conversely, being part of "a good team" provided a civil, supportive, facilitative work environment. Entering nurse education with previous healthcare experience had a mediating effect on the reported frequency of stressors. Newly qualified nurses encounter multiple work-related stressors over their first 12 months postqualifying, which are intrinsically entwined with their transition. Employing organizations need to be more proactive in managing their workload and addressing workplace incivility. © 2017 John Wiley & Sons Ltd.

  5. 31 CFR Appendix A to Part 500 - Qualifying International Institutions

    Science.gov (United States)

    2010-07-01

    ... Pt. 500, App. A Appendix A to Part 500—Qualifying International Institutions Asian Development Bank (ADB) Food and Agricultural Organization (FAO) International Bank for Reconstruction and Development (IBRD, the “World Bank”) International Civil Aviation Organization (ICAO) International Development...

  6. Qualification of Magnesium/Teflon/Viton Pyrotechnic Composition Used in Rocket Motors Ignition System

    Directory of Open Access Journals (Sweden)

    Luciana de Barros

    2016-04-01

    Full Text Available The application of fluoropolymers in high-energy-release pyrotechnic compositions is common in the space and defense areas. Pyrotechnic compositions of magnesium/Teflon/Viton are widely used in military flares and pyrogen igniters for igniting the solid propellant of a rocket motor. Pyrotechnic components are considered high-risk products as they may cause catastrophic accidents if initiated or ignited inadvertently. To reduce the hazards involved in the handling, storage and transportation of these devices, the magnesium/Teflon/Viton composition was subjected to various sensitivity tests, DSC and had its stability and compatibility tested with other materials. This composition obtained satisfactory results in all the tests, which qualifies it as safe for production, handling, use, storage and transportation.

  7. 77 FR 23373 - Small Business Investment Companies-Energy Saving Qualified Investments

    Science.gov (United States)

    2012-04-19

    ... appropriate for inclusion in the definition. Furthermore, if a Small Business generates revenues solely from... definition of Energy Saving Qualified Investment by adding a presumption that a Small Business will be...

  8. Lung response to ultrafine Kevlar aramid synthetic fibrils following 2-year inhalation exposure in rats.

    Science.gov (United States)

    Lee, K P; Kelly, D P; O'Neal, F O; Stadler, J C; Kennedy, G L

    1988-07-01

    Four groups of 100 male and 100 female rats were exposed to ultrafine Kevlar fibrils at concentrations of 0, 2.5, 25, and 100 fibrils/cc for 6 hr/day, 5 days/week for 2 years. One group was exposed to 400 fibrils/cc for 1 year and allowed to recover for 1 year. At 2.5 fibrils/cc, the lungs had normal alveolar architecture with a few dust-laden macrophages (dust cell response) in the alveolar airspaces. At 25 fibrils/cc, the lungs showed a dust cell response, slight Type II pneumocyte hyperplasia, alveolar bronchiolarization, and a negligible amount of collagenized fibrosis in the alveolar duct region. At 100 fibrils/cc, the same pulmonary responses were seen as at 25 fibrils/cc. In addition, cystic keratinizing squamous cell carcinoma (CKSCC) was found in 4 female rats, but not in male rats. Female rats had more prominent foamy alveolar macrophages, cholesterol granulomas, and alveolar bronchiolarization. These pulmonary lesions were related to the development of CKSCC. The lung tumors were derived from metaplastic squamous cells in areas of alveolar bronchiolarization. At 400 fibrils/cc following 1 year of recovery, the lung dust content, average fiber length, and the pulmonary lesions were markedly reduced, but slight centriacinar emphysema and minimal collagenized fibrosis were found in the alveolar duct region. One male and 6 female rats developed CKSCC. The lung tumors were a unique type of experimentally induced tumors in the rats and have not been seen as spontaneous tumors in man or animals. Therefore, the relevance of this type of lung tumor to the human situation is minimal.

  9. A missing piece of the workforce puzzle. The experiences of internationally qualified nurses in New Zealand: a literature review.

    Science.gov (United States)

    Jenkins, Brittany Lauren; Huntington, Annette

    2015-01-01

    To analyse the literature regarding the context and experiences of internationally qualified registered nurses, particularly Filipino and Indian nurses, who have transitioned to New Zealand. Internationally qualified nurses are a significant proportion of the nursing workforce in many developed countries including New Zealand. This is increasingly important as populations age, escalating demand for nurses. Understanding the internationally qualified nurse experience is required as this could influence migration in a competitive labour market. Examination of peer-reviewed research, policy and discussion documents, and technical reports. A systematic literature search sought articles published between 2001 and 2014 using Google Scholar, CINAHL, and Medline. Articles were critically appraised for relevance, transferability, and methodological rigour. Fifty-one articles met inclusion criteria and demonstrate internationally qualified nurses face significant challenges transitioning into New Zealand. The internationally qualified nurse experience of transitioning into a new country is little researched and requires further investigation.

  10. Statistically qualified neuro-analytic failure detection method and system

    Science.gov (United States)

    Vilim, Richard B.; Garcia, Humberto E.; Chen, Frederick W.

    2002-03-02

    An apparatus and method for monitoring a process involve development and application of a statistically qualified neuro-analytic (SQNA) model to accurately and reliably identify process change. The development of the SQNA model is accomplished in two stages: deterministic model adaption and stochastic model modification of the deterministic model adaptation. Deterministic model adaption involves formulating an analytic model of the process representing known process characteristics, augmenting the analytic model with a neural network that captures unknown process characteristics, and training the resulting neuro-analytic model by adjusting the neural network weights according to a unique scaled equation error minimization technique. Stochastic model modification involves qualifying any remaining uncertainty in the trained neuro-analytic model by formulating a likelihood function, given an error propagation equation, for computing the probability that the neuro-analytic model generates measured process output. Preferably, the developed SQNA model is validated using known sequential probability ratio tests and applied to the process as an on-line monitoring system. Illustrative of the method and apparatus, the method is applied to a peristaltic pump system.

  11. On the Structure and Dissolution Properties of Poly(p-phenylene terephthalamide) : Effect of Solvent Composition

    NARCIS (Netherlands)

    Westerhof, H.P.

    2009-01-01

    Poly-p-phenylenetherephthalamide (PpPTA) is a high performance, semi flexible polymer. Commercially it is mainly sold in the form of fibres under the trade names Twaron and Kevlar. The polymerization is performed in an amide(NMP)-salt(CaCl2) solution and afterwards spun into fibres from a sulphuric

  12. 26 CFR 20.2039-2 - Annuities under “qualified plans” and section 403(b) annuity contracts.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Annuities under âqualified plansâ and section 403(b) annuity contracts. 20.2039-2 Section 20.2039-2 Internal Revenue INTERNAL REVENUE SERVICE... AUGUST 16, 1954 Gross Estate § 20.2039-2 Annuities under “qualified plans” and section 403(b) annuity...

  13. 49 CFR 213.305 - Designation of qualified individuals; general qualifications.

    Science.gov (United States)

    2010-10-01

    ... college level engineering program, supplemented by special on the job training emphasizing the techniques... engineering program, supplemented by special on the job training emphasizing the techniques to be employed in... 49 Transportation 4 2010-10-01 2010-10-01 false Designation of qualified individuals; general...

  14. Stress and reliability analyses of multilayered composite cylinder under thermal and mechanical loads

    Science.gov (United States)

    Wang, Xiaohua

    The coupling resulting from the mutual influence of material thermal and mechanical parameters is examined in the thermal stress analysis of a multilayered isotropic composite cylinder subjected to sudden axisymmetric external and internal temperature. The method of complex frequency response functions together with the Fourier transform technique is utilized. Because the coupling parameters for some composite materials, such as carbon-carbon, are very small, the effect of coupling is neglected in the orthotropic thermal stress analysis. The stress distributions in multilayered orthotropic cylinders subjected to sudden axisymmetric temperature loading combined with dynamic pressure as well as asymmetric temperature loading are also obtained. The method of Fourier series together with the Laplace transform is utilized in solving the heat conduction equation and thermal stress analysis. For brittle materials, like carbon-carbon composites, the strength variability is represented by two or three parameter Weibull distributions. The 'weakest link' principle which takes into account both the carbon-carbon composite cylinders. The complex frequency response analysis is performed on a multilayered orthotropic cylinder under asymmetrical thermal load. Both deterministic and random thermal stress and reliability analyses can be based on the results of this frequency response analysis. The stress and displacement distributions and reliability of rocket motors under static or dynamic line loads are analyzed by an elasticity approach. Rocket motors are modeled as long hollow multilayered cylinders with an air core, a thick isotropic propellant inner layer and a thin orthotropic kevlar-epoxy case. The case is treated as a single orthotropic layer or a ten layered orthotropic structure. Five material properties and the load are treated as random variable with normal distributions when the reliability of the rocket motor is analyzed by the first-order, second-moment method (FOSM).

  15. Regulatory guides for qualifying the calculation methodology of Furnas by CNEN

    International Nuclear Information System (INIS)

    1987-10-01

    Regulatory guides are presented which will be used for qualifying the calculation methodology of FURNAS by CNEN, in the areas of Neutronics, Thermohydraulics, Accident Analysis and Fuel Rod Performance, as applied to Angra 1 NPP. (Author) [pt

  16. Space Qualified Non-Destructive Evaluation and Structural Health Monitoring Technology, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NextGen Aeronautics is proposing an innovative space qualified non-destructive evaluation and health monitoring technology. The technology is built on concepts...

  17. 12 CFR 24.6 - Examples of qualifying public welfare investments.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Examples of qualifying public welfare investments. 24.6 Section 24.6 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY... finance small businesses or small farms, including minority- and women-owned small businesses or small...

  18. 77 FR 9846 - Source of Income From Qualified Fails Charges

    Science.gov (United States)

    2012-02-21

    ... temporary regulations noted that no trading practice existed at that time for fails charges on securities other than Treasuries, but that if a fails charge trading practice pertaining to other securities was... sources within the United States, and the income from the qualified fails charge is treated as effectively...

  19. Professional paradox: identity formation in qualified doctors pursuing further training.

    Science.gov (United States)

    Chan, Mercedes; Pratt, Dan; Poole, Gary; Sidhu, Ravi

    2018-03-01

    Many newly qualified specialists and subspecialists pursue additional training. Although their motivations are many, the pursuit of further training as an alternative to unemployment is an emerging trend. Paradoxically, doctors continue as trainees with a consultant's credentials, and without the guarantee of eventual employment. This study explores seven doctors' experiences, the effects of further training on their professional identity formation (PIF), and how these effects are reconciled on a personal and professional level. This phenomenological study involved interviews with seven qualified Canadian specialists (three were female) who pursued additional training in response to a lack of available positions in their respective specialties. Template analysis generated theoretical constructs of influences on their PIF, and characteristics of their lived experiences. Four themes shaped PIF: setting and context; language and communication; responsibilities and privileges; and participants' visions of their future selves. Professional identity formation (PIF) continued to develop in further training, but was inconsistently affirmed by participants' communities of practice. Four major themes characterised training experiences: prescription; managing multiple masters; limiting access to others and community ties; and constantly questioning the value of extra training. Qualified doctors traverse professional paradoxes as they seek further education with no guarantee of employment and provide consultant-level care as 'trainees'. An identity dissonance emerges that may continue until a clear identity is prescribed for them. Although disruptive to these doctors' PIF and personal and professional lives, the long-term effects of additional training are unknown. Its utility and influence on securing employment and future job satisfaction are areas for further research. © 2017 John Wiley & Sons Ltd and The Association for the Study of Medical Education.

  20. Space Qualified Non-Destructive Evaluation and Structural Health Monitoring Technology, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Encouraged by Phase I accomplishments, the proposed Phase II program will significantly mature and align the development of a Space Qualified Non-Destructive...

  1. Qualifying cogeneration in Texas and Louisiana

    International Nuclear Information System (INIS)

    Jenkins, S.C.; Cabe, R.; Stauffaeher, J.J.

    1992-01-01

    This paper reports that cogeneration of electricity and useful thermal energy by industrials along the Gulf Coast grew significantly more rapidly than in other parts of the country during and immediately following World War II as a result of the concentration of chemical and plastics processing facilities there. In 1982, Texas passed its version of PURPA, the Public Utility Regulatory Act (PURA) and designated those non-utility generators from which public utilities must purchase electricity as Qualifying Cogenerators. In 1991, there were nearly 7,500 MW of QF power generated for inside-the-fence use or firm capacity sale to utilities, with the two largest utilities in Texas purchasing over half that amount

  2. The Development of Two Composite Energy Absorbers for Use in a Transport Rotorcraft Airframe Crash Testbed (TRACT 2) Full-Scale Crash Test

    Science.gov (United States)

    Littell, Justin D.; Jackson, Karen E.; Annett, Martin S.; Seal, Michael D.; Fasanella, Edwin L.

    2015-01-01

    Two composite energy absorbers were developed and evaluated at NASA Langley Research Center through multi-level testing and simulation performed under the Transport Rotorcraft Airframe Crash Testbed (TRACT) research program. A conical-shaped energy absorber, designated the conusoid, was evaluated that consisted of four layers of hybrid carbon-Kevlar plain weave fabric oriented at [+45deg/-45deg/-45deg/+45deg] with respect to the vertical direction. A sinusoidal-shaped energy absorber, designated the sinusoid, was developed that consisted of hybrid carbon-Kevlar plain weave fabric face sheets, two layers for each face sheet oriented at +/-45deg with respect to the vertical direction, and a closed-cell ELFOAM P200 polyisocyanurate (2.0-lb/cu ft) foam core. The design goal for the energy absorbers was to achieve average floor-level accelerations of between 25- and 40-g during the full-scale crash test of a retrofitted CH-46E helicopter airframe, designated TRACT 2. Variations in both designs were assessed through dynamic crush testing of component specimens. Once the designs were finalized, subfloor beams of each configuration were fabricated and retrofitted into a barrel section of a CH-46E helicopter. A vertical drop test of the barrel section was conducted onto concrete to evaluate the performance of the energy absorbers prior to retrofit into TRACT 2. The retrofitted airframe was crash tested under combined forward and vertical velocity conditions onto soft soil. Finite element models were developed of all test articles and simulations were performed using LS-DYNA, a commercial nonlinear explicit transient dynamic finite element code. Test-analysis results are presented for each energy absorber as comparisons of time-history responses, as well as predicted and experimental structural deformations and progressive damage under impact loading for each evaluation level.

  3. Pedagogical characteristics of the systems for assessing the technical and tactical skills of qualified volleyball players

    Directory of Open Access Journals (Sweden)

    Мykhailo Oliinyk

    2017-12-01

    Full Text Available Purpose: on the basis of the analysis of the special literature and their own experimental studies, to determine the characteristics of the systems for assessing the technical and tactical skills of qualified volleyball players. Material & Methods: study was conducted on the basis of the material of the national team of Zaporozhye State Medical University on volleyball. Analysis and generalization of the data of scientific and methodical literature are used; registration, analysis and interpretation of indicators of technical and tactical actions of qualified volleyball players in training and competitive processes; pedagogical observations; algorithms for calculating the quantitative and qualitative indicators of technical and tactical skill in volleyball; methods of mathematical statistics. Results: data on the existence of a strong statistical relationship between the systems of assessment of technical and tactical skills of qualified volleyball players, taking into account the specificity of the game role. Conclusion: shows the specifics of the application of various systems for assessing the technical and tactical skills of qualified volleyball players, taking into account the factors of the game role, noted the methodological features of special analysis and interpretation of indicators of technical and tactical actions in the adversarial process.

  4. Role of Inelastic Transverse Compressive Behavior and Multiaxial Loading on the Transverse Impact of Kevlar KM2 Single Fiber

    Directory of Open Access Journals (Sweden)

    Subramani Sockalingam

    2017-02-01

    Full Text Available High-velocity transverse impact of ballistic fabrics and yarns by projectiles subject individual fibers to multi-axial dynamic loading. Single-fiber transverse impact experiments with the current state-of-the-art experimental capabilities are challenging due to the associated micron length-scale. Kevlar® KM2 fibers exhibit a nonlinear inelastic behavior in transverse compression with an elastic limit less than 1.5% strain. The effect of this transverse behavior on a single KM2 fiber subjected to a cylindrical and a fragment-simulating projectile (FSP transverse impact is studied with a 3D finite element model. The inelastic behavior results in a significant reduction of fiber bounce velocity and projectile-fiber contact forces up to 38% compared to an elastic impact response. The multiaxial stress states during impact including transverse compression, axial tension, axial compression and interlaminar shear are presented at the location of failure. In addition, the models show a strain concentration over a small length in the fiber under the projectile-fiber contact. A failure criterion, based on maximum axial tensile strain accounting for the gage length, strain rate and multiaxial loading degradation effects are applied to predict the single-fiber breaking speed. Results are compared to the elastic response to assess the importance of inelastic material behavior on failure during a transverse impact.

  5. Effect and origin of the structure of hyperbranched polysiloxane on the surface and integrated performances of grafted Kevlar fibers

    Science.gov (United States)

    Zhang, Hongrui; Yuan, Li; Liang, Guozheng; Gu, Aijuan

    2014-11-01

    Four hyperbranched polysiloxanes (HPSis) with different molecular weights and concentration ratios of double bonds to epoxy groups (1:6.5-1:0.7) were synthesized and characterized. Each HPSi was facilely grafted onto surfaces of Kevlar fibers (KFs) to develop novel modified fibers (HPSi-g-KFs). The structures and integrated properties of HPSi-g-KFs as well as the origin behind were systematically investigated. Results show that HPSi-g-KFs have much rougher surface morphologies, and their surface free energies are as high as about 1.7 times that of KFs, showing greatly improved wettability. Besides, HPSi-g-KFs have excellent UV resistance after 168 h UV irradiation, the retentions of tenacity, energy to break, modulus and break extension are as high as 92, 86, 95 and 96%, respectively, while those of KFs are 66-85%. In addition, compared with KFs, HPSi-g-KFs have higher tensile tenacity and energy to break with similar modulus and break extension, much better thermal stability and flame retardancy. The nature of HPSi has different influence on different property of fibers, the HPSi with smaller molecular weight and more epoxy groups is beneficial to prepare HPSi-g-KFs with better wettability, while that with larger molecular weight and more double bonds tends to prepare HPSi-g-KF with better flame retardancy and UV resistance.

  6. Changes in sickness absenteeism following the introduction of a qualifying day for sickness benefit--findings from Sweden Post

    DEFF Research Database (Denmark)

    Voss, M; Floderus, B; Diderichsen, F

    2001-01-01

    AIMS: In 1993, a qualifying day without sickness benefit was introduced to the Swedish sickness benefit system. The aim of the present study is to investigate sickness absenteeism before and after the introduction of the qualifying day, in the light of conditions inside and outside working life....... METHODS: The study was based on 1,952 female and 2,229 male employees of Sweden Post. Sickness absence was measured by sickness incidence one year before and one year after the introduction of the qualifying day (sick-leave events/person days at risk). Information about explanatory factors was collected...

  7. Investigation on mechanical properties of basalt composite fabrics (experiment study

    Directory of Open Access Journals (Sweden)

    Talebi Mazraehshahi H.

    2010-06-01

    Full Text Available To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced and mechanical behaviors of this material investigated from view point of testing. For this study two type of fabric with different thickness used. Comparison between this composite reinforcement with popular reinforcement as carbon, glass, kevlar performed. To determine mechanical properties of epoxy based basalt fabric following test procedure performed : 1. Tensile testing according to ASTM D3039 in 0° and 90° direction to find ultimate strength in tension and shear, modulus of elasticity, elangation and ultimate strain. 2. Compression testing according to EN 2850 ultimate compression strength and maximum deformation under compression loading. 3. Shear testing according to ASTM D3518-94 to find in plane shear response of polymer matrix composites materials. 4. Predict flexural properties of sandwich construction which manufactured from basalt facing with PVC foam core according to ASTM C393-94. Material strength properties must be based on enough tests of material to meet the test procedure specifications [1]. For this reason six specimens were manufactured for testing and the tests were performed on them using an INSTRON machine model 5582. In the study, the effect of percent of resin in basalt reinforced composite was investigated. Also the weights of the ballast based composites with different percent of resin were measured with conventional composites. As the weight is an important parameter in aerospace industry when the designer wants to replace one

  8. 26 CFR 1.1275-6 - Integration of qualifying debt instruments.

    Science.gov (United States)

    2010-04-01

    ... § 1.483-4 or § 1.1275-4(c) (certain contingent payment debt instruments issued for nonpublicly traded... the qualifying debt instrument. A financial instrument that hedges currency risk is not a § 1.1275-6... denominated in pounds, the swap hedges only interest rate risk, not currency risk. Therefore, the transaction...

  9. HIGHLY QUALIFIED WORKING FORCE – KEY ELEMENT OF INNOVATIVE DEVELOPMENT MODEL

    Directory of Open Access Journals (Sweden)

    M. Avksientiev

    2014-12-01

    Full Text Available Highly qualified working force is a central element of intensive development model in modern society. The article surveys the experience of countries that managed to transform their economy to the innovative one. Ukrainian economy cannot stand aside processes that dominate the world economy trends, thus we are to use this experience to succeed in future. Today any government of the world is facing challenges that occur due to transformation of the economy into informational one. This type of economy causes its transformation form extensive to intensive one. The main reasons under that is limitation of nature resources, material factors of production. Thus this approach depends much on the quality of working force. Unfortunately in Ukraine there is a misbalance in specialist preparation. This puts additional pressure on the educational sphere also. In order to avoid this pressure we are to conduct reforms in education sphere. Nowadays, in the world views and concepts of governmental role in the social development are changing. This why, even at times of economic recession educational costs are not reduced under the new economical doctrine in the EU. Highly qualified specialists, while creating new products and services play role of engineers in XXI century. They are to lead their industries to world leading positions. From economic point of view, highly qualified specialists benefit society with higher income rates, taxation and thus, increasing the living standards in society. Thus, the majority if modern scientists prove the importance of highly trained working force for more effective economic development.

  10. 29 CFR 2520.104-46 - Waiver of examination and report of an independent qualified public accountant for employee...

    Science.gov (United States)

    2010-07-01

    ... qualified public accountant for employee benefit plans with fewer than 100 participants. 2520.104-46 Section... Requirements § 2520.104-46 Waiver of examination and report of an independent qualified public accountant for... public accountant to conduct an examination of the financial statements of the plan; (2) Include within...

  11. M2 qualify laser beam propagation

    International Nuclear Information System (INIS)

    Abdelhalim, Bencheikh; Mohamed, Bouafia

    2010-01-01

    One of the most important properties of a laser resonator is the highly collimated or spatially coherent nature of the laser output beam. Laser beam diameter and quality factor M 2 are significant parameters in a wide range of laser applications. This is because the spatial beam quality determines how closely the beam can be focused or how well the beam propagates over long distances without significant dispersion. In the present paper we have used three different methods to qualify the spatial structure of a laser beam propagating in free space, the results are obtained and discussed, and we have found that the Wigner distribution function is a powerful tool which allows a global characterization of any kind of beam

  12. 48 CFR 809.270 - Qualified products for convenience/labor-saving foods.

    Science.gov (United States)

    2010-10-01

    ... convenience/labor-saving foods. 809.270 Section 809.270 Federal Acquisition Regulations System DEPARTMENT OF... 809.270 Qualified products for convenience/labor-saving foods. (a) Each VISN Nutrition and Food Service representative is authorized to establish a common VISN QPL for convenience and labor-saving foods...

  13. A versatile electrical penetration design qualified to IEEE Std. 317-1983

    International Nuclear Information System (INIS)

    Lankenau, W.; Wetherill, T.M.

    1994-01-01

    Although worldwide demand for new construction of nuclear power stations has been on a decline, the available opportunities for the design and construction of qualified electrical penetrations continues to offer challenges, requiring a highly versatile design. Versatility is necessary in order to meet unique customer requirements within the constraints of a design basis qualified to IEEE Std. 317-1983. This paper summarizes such a versatile electrical penetration designed, built and tested to IEEE Std. 317-1983. The principal features are described including major materials of construction. Some of the design constraints such as sealing requirements, and conductor density (including numerical example) are discussed. The requirements for qualification testing of the penetration assembly to IEEE Std. 317-1983 are delineated in a general sense, and some typical test ranges for preconditioning, radiation exposure, and LOCA are provided. The paper concludes by describing ways in which this versatile design has been adapted to meet unique customer requirements in a variety of nuclear power plants

  14. Roles and Responsibilities, and Education and Training Requirements for Clinically Qualified Medical Physicists (Russian Edition)

    International Nuclear Information System (INIS)

    2014-01-01

    This publication addresses the shortfall of well trained and clinically qualified medical physicists working in radiation medicine. The roles, responsibilities and clinical training requirements of medical physicists have not always been well defined or well understood by health care professionals, health authorities and regulatory agencies. To fill this gap, this publication provides recommendations for the academic education and clinical training of clinically qualified medical physicists, including recommendations for their accreditation certification and registration, along with continuous professional development. The goal is to establish criteria that support the harmonization of education and clinical training worldwide

  15. 76 FR 64879 - Deduction for Qualified Film and Television Production Costs

    Science.gov (United States)

    2011-10-19

    ... Deduction for Qualified Film and Television Production Costs AGENCY: Internal Revenue Service (IRS... regulations relating to deductions for the costs of producing film and television productions. Those temporary... production costs. (a) * * * (1) * * * (ii) [The text of this proposed amendment to Sec. 1.181- 1(a)(1)(ii) is...

  16. Newly Qualified Teachers' Professional Digital Competence: Implications for Teacher Education

    Science.gov (United States)

    Gudmundsdottir, Greta Björk; Hatlevik, Ove Edvard

    2018-01-01

    The professional digital competence (PDC) of teachers is of growing importance in classrooms, now that digital resources and digital media are becoming important parts of teachers' everyday practice. This study explores how newly qualified teachers are prepared to use information and communication technology (ICT) in their initial teacher…

  17. 42 CFR 423.884 - Requirements for qualified retiree prescription drug plans.

    Science.gov (United States)

    2010-10-01

    ... actuary who is a member of the American Academy of Actuaries. Applicants may use qualified outside actuaries, including (but not limited to) actuaries employed by the plan administrator or an insurer providing benefits under the plan. If an applicant uses an outside actuary, the attestation can be submitted...

  18. 40 CFR 73.81 - Qualified conservation measures and renewable energy generation.

    Science.gov (United States)

    2010-07-01

    ...)) without increasing the use by the customer of any fuel other than qualified renewable energy, industrial waste heat, or, pursuant to paragraph (b)(5) of this section, industrial waste gases; (ii) Is... pursuant to § 73.82(c); or (5) Utilization of industrial waste gases, unless the applicant has certified...

  19. 26 CFR 1.856-9 - Treatment of certain qualified REIT subsidiaries.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Treatment of certain qualified REIT subsidiaries. 1.856-9 Section 1.856-9 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment Trusts § 1.856-9 Treatment of certain...

  20. 26 CFR 301.6361-1 - Collection and administration of qualified taxes.

    Science.gov (United States)

    2010-04-01

    ... chapter 1 (and the civil and criminal sanctions provided by subtitle F, or by title 18 of the United States Code (relating to crimes and criminal procedure), with respect to such collection and... for tax of another State or political subdivision—(i) In general. A credit allowable under a qualified...

  1. What Motivates Low-Qualified Employees to Participate in Training and Development? A Mixed-Method Study on their Learning Intentions

    Science.gov (United States)

    Kyndt, Eva; Govaerts, Natalie; Claes, Trees; De La Marche, Jens; Dochy, Filip

    2013-01-01

    The current research starts from the observation that low-qualified employees hold a vulnerable position on the labour market. It has been argued that learning and development can decrease this vulnerability; unfortunately research has shown that low-qualified employees participate considerably less in learning activities in comparison with…

  2. APPROACH TO SYNTHESIS OF PASSIVE INFRARED DETECTORS BASED ON QUASI-POINT MODEL OF QUALIFIED INTRUDER

    Directory of Open Access Journals (Sweden)

    I. V. Bilizhenko

    2017-01-01

    Full Text Available Subject of Research. The paper deals with synthesis of passive infra red (PIR detectors with enhanced detection capability of qualified intruder who uses different types of detection countermeasures: the choice of specific movement direction and disguise in infrared band. Methods. We propose an approach based on quasi-point model of qualified intruder. It includes: separation of model priority parameters, formation of partial detection patterns adapted to those parameters and multi channel signal processing. Main Results. Quasi-pointmodel of qualified intruder consisting of different fragments was suggested. Power density difference was used for model parameters estimation. Criteria were formulated for detection pattern parameters choice on the basis of model parameters. Pyroelectric sensor with nine sensitive elements was applied for increasing the signal information content. Multi-channel processing with multiple partial detection patterns was proposed optimized for detection of intruder's specific movement direction. Practical Relevance. Developed functional device diagram can be realized both by hardware and software and is applicable as one of detection channels for dual technology passive infrared and microwave detectors.

  3. High-energy ion implantation of polymeric fibers for modification of reinforcement-matrix adhesion

    International Nuclear Information System (INIS)

    Grummon, D.S.; Schalek, R.; Ozzello, A.; Kalantar, J.; Drzal, L.T.

    1991-01-01

    We have previously reported on the effect of high-energy ion irradiation of ultrahigh molecular weight polyethylene (UHMW-PE), and Kevlar-49 polyaramid fibers, on fiber-matrix adhesion and interfacial shear strength (ISS) in epoxy matrix composites. Irradiation of UHMW-PE fibers produced large improvements in interfacial shear strength, without degrading fiber tensile strength. ISS was not generally affected in irradiated Kevlar-49, and fiber tensile strength decreased. The divergence in response between polyaramid and polyethylene relates both to differences in the mesoscopic structure of the individual fibers, and to the different forms of beam induced structural modification favored by the individual polymer chemistries. Here we report results of surface energy measurements, infrared spectroscopy analysis, and X-ray photoelectron spectroscopy studies on UHMW-PE and polyaramid fibers, irradiated to fluences between 2x10 12 and 5x10 15 cm -2 with N + , Ar + , Ti + , Na + , and He + at energies between 30 and 400 keV. UHMW-PE fibers showed a pronounced increase in the polar component of surface energy which could be associated with carbonyl, hydroxyl and hydroperoxide groups at the surface. Kevlar, on the other hand, tended toward carbonization and showed a decrease in nitrogen and oxygen concentrations and a sharp drop in polar surface energy. (orig.)

  4. Assessment of various failure theories for weight and cost optimized laminated composites using genetic algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Goyal, T. [Indian Institute of Technology Kanpur. Dept. of Aerospace Engineering, UP (India); Gupta, R. [Infotech Enterprises Ltd., Hyderabad (India)

    2012-07-01

    In this work, minimum weight-cost design for laminated composites is presented. A genetic algorithm has been developed for the optimization process. Maximum-Stress, Tsai-Wu and Tsai-Hill failure criteria have been used along with buckling analysis parameter for the margin of safety calculations. The design variables include three materials; namely Carbon-Epoxy, Glass-Epoxy, Kevlar-Epoxy; number of plies; ply orientation angles, varying from -75 deg. to 90 deg. in the intervals of 15 deg. and ply thicknesses which depend on the material in use. The total cost is a sum of material cost and layup cost. Layup cost is a function of the ply angle. Validation studies for solution convergence and weight-cost inverse proportionality are carried out. One set of results for shear loading are also validated from literature for a particular case. A Pareto-Optimal solution set is demonstrated for biaxial loading conditions. It is then extended to applied moments. It is found that global optimum for a given loading condition is a function of the failure criteria for shear loading, with Maximum Stress criteria giving the lightest-cheapest and Tsai-Wu criteria giving the heaviest-costliest optimized laminates. Optimized weight results are plotted from the three criteria to do a comparative study. This work gives a global optimized laminated composite and also a set of other local optimum laminates for a given set of loading conditions. The current algorithm also provides with adequate data to supplement the use of different failure criteria for varying loadings. This work can find use in the industry and/or academia considering the increased use of laminated composites in modern wind blades. (Author)

  5. Data Compilation for AGR-1 Baseline Coated Particle Composite LEU01-46T

    International Nuclear Information System (INIS)

    Hunn, John D.; Lowden, Richard Andrew

    2006-01-01

    This document is a compilation of characterization data for the AGR-1 baseline coated particle composite LEU01-46T, a composite of four batches of TRISO-coated 350 (micro)m 19.7% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The AGR-1 TRISO-coated particles consist of a spherical kernel coated with a ∼ 50% dense carbon buffer layer (100 (micro)m nominal thickness) followed by a dense inner pyrocarbonlayer (40 (micro)m nominal thickness) followed by a SiC layer (35 (micro)m nominal thickness) followed by another dense outer pyrocarbon layer (40 (micro)m nominal thickness). The coated particles, were produced by ORNL for the Advanced Gas Reactor Fuel Development and Qualification (AGR) program to be put into compacts for insertion in the first irradiation test capsule, AGR-1. The kernels were obtained from BWXT and identified as composite (G73D-20-69302). The BWXT kernel lot G73D-20-69302 was riffled into sublots for characterization and coating by ORNL and identified as LEU01-?? (where ?? is a series of integers beginning with 01). Additional particle batches were coated with only buffer or buffer plus inner pyrocarbon (IPyC) layers using similar process conditions as used for the full TRISO batches comprising the LEU01-46T composite. These batches were fabricated in order to qualify that the process conditions used for buffer and IPyC would produce acceptable densities, as described in sections 8 and 9. These qualifying batches used 350 (micro)m natural uranium oxide/uranium carbide kernels (NUCO). The kernels were obtained from BWXT and identified as composite G73B-NU-69300. The use of NUCO surrogate kernels is not expected to significantly effect the densities of the buffer and IPyC coatings. Confirmatory batches using LEUCO kernels from G73D-20-69302 were coated and characterized to verify this assumption. The AGR-1 Fuel Product Specification and Characterization Guidance (INL EDF-4380, Rev. 6) provides the requirements necessary for acceptance

  6. Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II. Part 2; Ballistic Impact Testing

    Science.gov (United States)

    Revilock, D. M.; Pereira, J. M.

    2009-01-01

    This report summarizes the ballistic impact testing that was conducted to provide validation data for the development of numerical models of blade-out events in fabric containment systems. The ballistic impact response of two different fiber materials - Kevlar(TradeName) 49 and Zylon(TradeName) AS (as spun) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation, and velocity of the projectile were varied and recorded. In most cases, the tests were designed so the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models to predict the response of fabrics under conditions that simulate those of a jet engine blade-release situation. In addition, some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different fabric materials.

  7. Damping in aerospace composite materials

    Science.gov (United States)

    Agneni, A.; Balis Crema, L.; Castellani, A.

    Experimental results are presented on specimens of carbon and Kevlar fibers in epoxy resin, materials used in many aerospace structures (control surfaces and wings in aircraft, large antennas in spacecraft, etc.). Some experimental methods of estimating damping ratios are first reviewed, either in the time domain or in the frequency domain. Some damping factor estimates from experimental tests are then shown; in order to evaluate the effects of the aerospace environment, damping factors have been obtained in a typical range of temperature, namely between +120 C and -120 C, and in the pressure range from room pressure to 10 exp -6 torr. Finally, a theoretical approach for predicting the bounds of the damping coefficients is shown, and prediction data are compared with experimental results.

  8. Skills upgrading for newly qualified surgeon: Is the district hospital in ...

    African Journals Online (AJOL)

    With adequate surgical activity in these settings, the trainee's confidence is boosted to the point of independence. This skill acquisition is a continuous process, especially so for those who qualify from an exit training program like the one at the University of Nairobi (UON). The continuity is maintained for two years after.

  9. 47 CFR 13.201 - Qualifying for a commercial operator license or endorsement.

    Science.gov (United States)

    2010-10-01

    ... class of license or endorsement specified below must pass, or otherwise receive credit for, the... endorsement. 13.201 Section 13.201 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMERCIAL RADIO OPERATORS Examination System § 13.201 Qualifying for a commercial operator license or endorsement...

  10. Target language use in Modern Language classrooms: perception and change among newly qualified teachers in Scotland

    OpenAIRE

    Lynch, Michael Patrick

    2015-01-01

    In this thesis I investigate the practices and perceptions of some Newly Qualified Teachers (NQTs) of modern foreign languages (MFL) in Scotland in relation to how they use the target language (L2). I seek to answer the questions “In what different ways do student teachers of modern languages use the target language in Scottish secondary school classrooms?’, ‘What reasons do they give for how they use it?” and “In what way(s), if any, do newly qualified teachers of modern language...

  11. Worst-case prediction of normal operating containment temperatures for environmentally qualified equipment

    International Nuclear Information System (INIS)

    Krasnopoler, M.J.; Sundergill, J.E.

    1991-01-01

    Due to issues raised in NRC Information Notice No. 87-65, a southern US nuclear plant was concerned about thermal aging of environmentally qualified (EQ) equipment located in areas of elevated containment temperatures. A method to predict the worst-case monthly temperatures at various zones in the containment and calculate the qualified life using this monthly temperature was developed. Temperatures were predicted for twenty locations inside the containment. Concern about the qualified life of EQ equipment resulted from normal operating temperatures above 120F in several areas of the containment, especially during the summer. At a few locations, the temperature exceeded 140F. Also, NRC Information Notice No. 89-30 reported high containment temperatures at three other nuclear power plants. The predicted temperatures were based on a one-year containment temperature monitoring program. The monitors included permanent temperature monitors required by the Technical Specifications and temporary monitors installed specifically for this program. The temporary monitors were installed near EQ equipment in the expected worst-case areas based on design and operating experience. A semi-empirical model that combined physical and statistical models was developed. The physical model was an overall energy balance for the containment. The statistical model consists of several linear regressions that conservatively relate the monitor temperatures to the bulk containment temperature. The resulting semi-empirical model predicts the worst-case monthly service temperatures at the location of each of the containment temperature monitors. The monthly temperatures are the maximum expected because they are based on the historically worst-case atmospheric data

  12. Qualifying codes under software quality assurance: Two examples as guidelines for codes that are existing or under development

    Energy Technology Data Exchange (ETDEWEB)

    Mangold, D.

    1993-05-01

    Software quality assurance is an area of concem for DOE, EPA, and other agencies due to the poor quality of software and its documentation they have received in the past. This report briefly summarizes the software development concepts and terminology increasingly employed by these agencies and provides a workable approach to scientific programming under the new requirements. Following this is a practical description of how to qualify a simulation code, based on a software QA plan that has been reviewed and officially accepted by DOE/OCRWM. Two codes have recently been baselined and qualified, so that they can be officially used for QA Level 1 work under the DOE/OCRWM QA requirements. One of them was baselined and qualified within one week. The first of the codes was the multi-phase multi-component flow code TOUGH version 1, an already existing code, and the other was a geochemistry transport code STATEQ that was under development The way to accomplish qualification for both types of codes is summarized in an easy-to-follow step-by step fashion to illustrate how to baseline and qualify such codes through a relatively painless procedure.

  13. Qualifying codes under software quality assurance: Two examples as guidelines for codes that are existing or under development

    International Nuclear Information System (INIS)

    Mangold, D.

    1993-05-01

    Software quality assurance is an area of concern for DOE, EPA, and other agencies due to the poor quality of software and its documentation they have received in the past. This report briefly summarizes the software development concepts and terminology increasingly employed by these agencies and provides a workable approach to scientific programming under the new requirements. Following this is a practical description of how to qualify a simulation code, based on a software QA plan that has been reviewed and officially accepted by DOE/OCRWM. Two codes have recently been baselined and qualified, so that they can be officially used for QA Level 1 work under the DOE/OCRWM QA requirements. One of them was baselined and qualified within one week. The first of the codes was the multi-phase multi-component flow code TOUGH version 1, an already existing code, and the other was a geochemistry transport code STATEQ that was under development The way to accomplish qualification for both types of codes is summarized in an easy-to-follow step-by step fashion to illustrate how to baseline and qualify such codes through a relatively painless procedure

  14. 76 FR 71450 - Deduction for Qualified Film and Television Production Costs; Correction

    Science.gov (United States)

    2011-11-18

    ... Deduction for Qualified Film and Television Production Costs; Correction AGENCY: Internal Revenue Service... Register on Wednesday, October 19, 2011 (76 FR 64816) relating to deductions for the cost of producing film and television productions. DATES: This correction is effective on November 18, 2011, and is...

  15. 6 CFR 25.6 - Procedures for designation of qualified anti-terrorism technologies.

    Science.gov (United States)

    2010-01-01

    ...-terrorism technologies. 25.6 Section 25.6 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY REGULATIONS TO SUPPORT ANTI-TERRORISM BY FOSTERING EFFECTIVE TECHNOLOGIES § 25.6 Procedures for designation of qualified anti-terrorism technologies. (a) Application Procedure. Any person, firm or other...

  16. Qualifying commercial grade instruments for use in nuclear power generating stations

    International Nuclear Information System (INIS)

    Lamothe, R.J.; Scally, C.R.

    1983-01-01

    Nuclear environmental qualification of instrumentation has been successfully accomplished by many commercial grade equipment manufacturers. This paper was prepared as a guide to those manufacturers who want some insight into a qualification program. The areas addressed are the regulations and documents, the qualification program, and a case history of a chart recorder qualifications. The principal standards relating to a nuclear qualification program are IEEE Std. 323-1974 IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations, IEEE Std. 344-1975 IEEE Recommended Practices for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations and 10CFR50.49. Previously NUREG 0588 Interim Staff Position on Environmental Qualification of Safety-Related Equipment. These define the intent and purpose of the qualification. The qualification program itself consists of several distinct parts which require explanation, including the determination of qualified life, choice of test samples, selection of appropriate acceptance criteria, aging program, radiation testing, seismic testing, abnormal environment tests and others. The case history illustrates the qualification program and the thought processes involved

  17. Use of CYPRES™ cutters with a Kevlar clamp band for hold-down and release of the Icarus De-Orbit Sail payload on TechDemoSat-1

    Science.gov (United States)

    Kingston, J.; Hobbs, S.; Roberts, P.; Juanes-Vallejo, C.; Robinson, F.; Sewell, R.; Snapir, B.; Llop, J. Virgili; Patel, M.

    2014-07-01

    TechDemoSat-1 is a UK-funded technology demonstration satellite, carrying 8 payloads provided by UK organisations, which is due to be launched in the first quarter of 2014. Cranfield University has supplied a De-Orbit Sail (DOS) payload to allow the mission to comply with end-of-life debris mitigation guidelines. The payload provides a passive, simple, and low-cost means of mitigating debris proliferation in Low Earth Orbit, by enhancing spacecraft aerodynamic drag at end-of-life and reducing time to natural orbital decay and re-entry. This paper describes the use of small commercial electro-explosive devices (EEDs), produced for use as parachute tether-cutters in reserve chute deployment systems, as low-cost but high-reliability release mechanisms for space applications. A testing campaign, including thermal vacuum and mechanical vibration, is described, which demonstrates the suitability of these CYPRES™ cutters, with a flexible Kevlar clamp band, for use as a hold-down and release mechanism (HDRM) for a deployable de-orbit sail. The HDRM is designed to be three-failure-tolerant, highly reliable, yet simple and low-cost.

  18. Gender Inequalities in Highly Qualified Professions: A Social Psychological Analysis

    OpenAIRE

    Santos, Maria Helena; Amâncio, Lígia

    2016-01-01

    Research in social and political psychology contributes towards understanding the persistence of job market gender segregation prevailing in recent decades, the consequences for those involved and their reactions when having to cope with gender inequality. Within the framework of the literature on shared ideologies that justify and legitimize discrimination against women, this article focuses on Portugal and analyses the particular case of women in two highly qualified professions traditional...

  19. Improvement of technique of a jerk of the qualified sportswomen in weightlifting

    Directory of Open Access Journals (Sweden)

    Oksana Solodka

    2016-12-01

    Full Text Available Purpose: the improvement of technical preparedness of the qualified female weight-lifters taking into account the group model characteristics of technique of a jerk. Material & Methods: analysis and synthesis of data of scientific and methodical literature, pedagogical experiment, method of mathematical statistics. Results: the revealed shortcomings of technique of the execution of a jerk of the qualified female weight-lifters were, considering the group model characteristics of technique of a jerk of the first group of weight categories. Complexes of compensatory exercises were offered for the purpose of correction. Conclusions: the performance of complexes of the compensatory exercises, which are directed to the improvement of competitive exercise of a jerk of bar, allowed to increase the number of successfully executed raising of bar, for 10,3–19,8%, according to initial indicators of number of rises, and also to receive positive shifts in motive structure of a jerk of bar.

  20. Can Social Robots Qualify for Moral Consideration? Reframing the Question about Robot Rights

    Directory of Open Access Journals (Sweden)

    Herman T. Tavani

    2018-03-01

    Full Text Available A controversial question that has been hotly debated in the emerging field of robot ethics is whether robots should be granted rights. Yet, a review of the recent literature in that field suggests that this seemingly straightforward question is far from clear and unambiguous. For example, those who favor granting rights to robots have not always been clear as to which kinds of robots should (or should not be eligible; nor have they been consistent with regard to which kinds of rights—civil, legal, moral, etc.—should be granted to qualifying robots. Also, there has been considerable disagreement about which essential criterion, or cluster of criteria, a robot would need to satisfy to be eligible for rights, and there is ongoing disagreement as to whether a robot must satisfy the conditions for (moral agency to qualify either for rights or (at least some level of moral consideration. One aim of this paper is to show how the current debate about whether to grant rights to robots would benefit from an analysis and clarification of some key concepts and assumptions underlying that question. My principal objective, however, is to show why we should reframe that question by asking instead whether some kinds of social robots qualify for moral consideration as moral patients. In arguing that the answer to this question is “yes,” I draw from some insights in the writings of Hans Jonas to defend my position.

  1. Computer Tomography Analysis of Fastrac Composite Thrust Chamber Assemblies

    Science.gov (United States)

    Beshears, Ronald D.

    2000-01-01

    Computed tomography (CT) inspection has been integrated into the production process for NASA's Fastrac composite thrust chamber assemblies (TCAs). CT has been proven to be uniquely qualified to detect the known critical flaw for these nozzles, liner cracks that are adjacent to debonds between the liner and overwrap. CT is also being used as a process monitoring tool through analysis of low density indications in the nozzle overwraps. 3d reconstruction of CT images to produce models of flawed areas is being used to give program engineers better insight into the location and nature of nozzle flaws.

  2. Strategy for development modes competent performance in teachers qualified alternative

    Directory of Open Access Journals (Sweden)

    Sailí Rodríguez Fuentes

    2017-12-01

    Full Text Available Introduction: the process of professionalization of the teacher is a subject of contemporary conjuncture, which is debated and investigated by researchers from dissimilar edges. Objective: to contribute to the professionalization process of qualified teachers of Technical and Vocational Education through a pedagogical strategy. Materials and methods: The materialist dialectic is used as a general method, allowing the study of the object as a process, the determination of its components, as well as its contradictions. theoretical methods: the historical and logical to delve into the regularities and qualities of reality in the polytechnic centers. Essential empirical methods were used: the documentary analysis that included the professional model; study plans, to obtain authentic and reliable information for research, interviews with students with the purpose of analyzing the manifestations of the professionalization process of the students and the direction of the process by the teachers, the observation of teaching activities allowed to diagnose the object , the demonstration of the problem, as well as the results of the practice of the strategy to be implemented. Results: a pedagogical strategy is designed and implemented to perfect the competent professional performance modes in the qualified professors. Conclusions: it contributed to the improvement of the professionalization process in favor of the competent professional modes of action.

  3. 'Newness-struggle-success' continuum: a qualitative examination of the cultural adaptation process experienced by overseas-qualified dentists in Australia.

    Science.gov (United States)

    Balasubramanian, Madhan; Brennan, David S; Spencer, A John; Short, Stephanie D

    2016-04-01

    Objectives Overseas-qualified dentists constitute a significant proportion of the Australian dental workforce (approximately one in four). The aim of the present study was to provide a better understanding of the cultural adaptation process of overseas-qualified dentists in Australia, so as to facilitate their integration into the Australian way of life and improve their contribution to Australian healthcare, economy and society. Methods Life stories of 49 overseas-qualified dentists from 22 countries were analysed for significant themes and patterns. We focused on their settlement experience, which relates to their social and cultural experience in Australia. This analysis was consistent with a hermeneutic phenomenological approach to qualitative social scientific research. Results Many participants noted that encounters with 'the Australian accent' and 'slang' influenced their cultural experience in Australia. Most of the participants expressed 'fascination' with the people and lifestyle in Australia, primarily with regard to the relaxed way of life, cultural diversity and the freedom one usually experiences living in Australia. Few participants expressed 'shock' at not being able to find a community of similar religious faith in Australia, as they are used to in their home countries. These issues were analysed in two themes; (1) language and communication; and (2) people, religion and lifestyle. The cultural adaptation process of overseas-qualified dentists in Australia is described as a continuum or superordinate theme, which we have entitled the 'newness-struggle-success' continuum. This overarching theme supersedes and incorporates all subthemes. Conclusion Family, friends, community and organisational structures (universities and public sector) play a vital role in the cultural learning process, affecting overseas-qualified dentist's ability to progress successfully through the cultural continuum. What is known about the topic? Australia is a popular host

  4. Qualified market access and inter-disciplinarity

    Directory of Open Access Journals (Sweden)

    Lisa Herzog

    2014-05-01

    Full Text Available This note offers reflections on qualified market access (QMA—the practice of linking trade agreements to values such as human rights, labour standards, or environmental protection. This idea has been suggested by political theorists as a way of fulfilling our duties to the global poor and of making the global economic system more just, and it has influenced a number of concrete policies, such as European Union (EU trade policies. Yet, in order to assess its merits tout court, different perspectives and disciplines need to be brought together, such as international law, economics, political science, and philosophy. It is also worth reflecting on existing practices, such as those of the EU. This note summarises some insights about QMA by drawing such research together and considers the areas in which further research is needed, whilst reflecting also on the merits of interdisciplinary exchanges on such topics.

  5. Gas target with thin wall

    International Nuclear Information System (INIS)

    Korenchenko, A.S.; Korenchenko, S.M.; Kravchuk, N.P.; Filippov, A.I.; Fursov, A.P.

    1992-01-01

    The technology of targets manufacture with thin wall diameter 100 mm and lengthwise 700 mm from composition kevlar + epoxy resin is described. The test's results on pressure and vacuum are reported. The created targets are supposed to be used on the installation ARES for an investigation of muons and pions interactions with light nuclei and rare pions decay 'on flying'. 5 refs.; 2 figs.; 2 tabs

  6. Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

    Energy Technology Data Exchange (ETDEWEB)

    Hanan, Jay C. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: jay.hanan@okstate.edu; Mahesh, Sivasambu [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Uestuendag, Ersan [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States)]. E-mail: ersan@caltech.edu; Beyerlein, Irene J. [Theoretical Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Swift, Geoffrey A. [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Clausen, Bjorn [Department of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Brown, Donald W. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Bourke, Mark A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2005-06-15

    The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al{sub 2}O{sub 3}-fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture.

  7. Strain evolution after fiber failure in a single-fiber metal matrix composite under cyclic loading

    International Nuclear Information System (INIS)

    Hanan, Jay C.; Mahesh, Sivasambu; Uestuendag, Ersan; Beyerlein, Irene J.; Swift, Geoffrey A.; Clausen, Bjorn; Brown, Donald W.; Bourke, Mark A.M.

    2005-01-01

    The evolution of in situ elastic strain with cyclic tensile loading in each phase of a single Al 2 O 3 -fiber/aluminum-matrix composite was studied using neutron diffraction (ND). An analytical model appropriate for metal matrix composites (MMCs) was developed to connect the measured axial strain evolution in each phase with the possible micromechanical events that could occur during loading at room temperature: fiber fracture, interfacial slipping, and matrix plastic deformation. Model interpretation showed that the elastic strain evolution in the fiber and matrix was governed by fiber fracture and interface slipping and not by plastic deformation of the matrix, whereas the macroscopic stress-strain response of the composite was influenced by all three. The combined single-fiber composite model and ND experiment introduces a new and quick engineering approach for qualifying the micromechanical response in MMCs due to cyclic loading and fiber fracture

  8. 26 CFR 1.1202-2 - Qualified small business stock; effect of redemptions.

    Science.gov (United States)

    2010-04-01

    ... purchased from the decedent's estate, beneficiary (whether by bequest or lifetime gift), heir, surviving.... Stock acquired by a taxpayer is not qualified small business stock if, in one or more purchases during... corporation purchases (directly or indirectly) more than a de minimis amount of its stock from the taxpayer or...

  9. Bank Officers’ Perceptions and Uses of Qualified Audit Reports

    DEFF Research Database (Denmark)

    Sormunen, Nina

    2014-01-01

    Purpose – The purpose of this study is to provide insights into the perceptions and uses of qualified audit reports in financial statements of small- and medium-sized enterprises (SMEs). As there is a long-standing debate on the usefulness of auditor’s going-concern reports, this study aims....... Practical implications – Regulators have taken the action to improve the auditor’s reporting model, and the findings provided by this study are important because they provide a deeper understanding of the perceptions and uses of audit reports from smaller companies. The study also contributes knowledge...

  10. Molecular-Level Study of the Effect of Prior Axial Compression/Torsion on the Axial-Tensile Strength of PPTA Fibers

    Science.gov (United States)

    2013-07-16

    Fig. 2 Eight length scales encountered in the study of polymer-matrix composite materials reinforced with high-performance fiber -based struc- tures...G13 = G31, G23 = G32), and three Poisson s ratios m12 (= m21 9E11/E22), m13 (= m31 9E11/E33) and m23 (= m32 9E22/E33), are next determined using...for Kevlar- Fiber Reinforced Polymer-Matrix Composites, J. Mater. Eng. Perform., 2013, 22, p 681–695 4. M. Grujicic, S. Ramaswami, J. S. Snipes, R

  11. Compression fatigue of Wind Turbine Blade composites materials and damage mechanisms

    DEFF Research Database (Denmark)

    Fraisse, Anthony; Brøndsted, Povl

    According to the new IEC 61400-5-rev0 recommendation, which is under preparation it will be required to qualify wind turbine blade (WTB) composite materials in fatigue at R=0.1, R=-1, and R=10. As a minimum fatigue at R=-1 is required. This is a consequence of the ever-growing blades, where gravity...... driven edgewise bending introduces significant fully reversed cycling at the leading and trailing edges. Therefore, material manufacturer and WTB manufacturer demand test results of highest reliability and reproducibility. However, these equirements for compression-compression and tensioncompression...

  12. 26 CFR 1.593-8 - Allocation of pre-1952 surplus to opening balance of reserve for losses on qualifying real...

    Science.gov (United States)

    2010-04-01

    ... real property loans shall not be treated as a reserve for bad debts for any purpose other than... of reserve for losses on qualifying real property loans. 1.593-8 Section 1.593-8 Internal Revenue... for losses on qualifying real property loans. (a) General rule. In the case of a taxpayer described in...

  13. Qualifying for Career Planning

    Directory of Open Access Journals (Sweden)

    Aleksandra Kovač

    1996-12-01

    Full Text Available The need for education in various spheres of life, which allows a person to fully develop his/her personality, is more and more presen t also in our society. The discussed educational programme Discovering Vocational Goals and Forming Strategies· to Realize them qualifies people for autonomous career planning by offer­ ing them one of the possible ways of making decisions in relation to profession and job. In the course of the realization of the programme the participants are given the chance to think about the kind of work that would suit their interests, capabilities and individual characteristics as weel as the needs in certain environments (possible employers. They are encouraged to make an actual plan, stating how and when the desired objective will be reached. In 1995 the pro­ gramme was being carried out within nine semi­ nars organized at the Employment Offices in Maribor and Ptuj. During that time the pro­ gramme has also been evaluated by Doba - Education Office, which was funded by the Ministry of Work, Family and Social Matters. The paper includes the content of the programme as well as the assessments of the research project. The presented data show that the participants learned the method of career planning and acqu­ired greater self-confidence and motivation to solve their job problem actively.

  14. Information Support of Highly-Qualified Archers’ Training

    Directory of Open Access Journals (Sweden)

    А. П. Власов

    2017-03-01

    Full Text Available The objective is to ground the ways of improving the level of technical preparedness of highly-qualified archers by means of video and multimedia technologies. Materials and methods: The research studied motor actions of 25 athletes of the national team of Ukraine in archery when they were performing training exercises indoors (exercising area and outdoors (archery range. Each athlete’s technique of executing shooting exercises was video recorded in sequence from different angles (from above, from behind, from the front, from the left and the right sides depending on the shooting line with a digital video camera Sony DCR-XR150E. The processing of the video materials was done with the Dartfish Connekt software package. Results: The research grounds the need to use video and multimedia technologies in the process of training of highly-qualified archers. Such methods aim at improving the skills of both coaches and athletes by helping them better understand all aspects of the training exercises execution. Multimedia means offer a delayed-in-time opportunity to watch the video recording of the training after its preliminary computer processing. It enables the coach and the athlete to focus on the analysis of the execution of the entire exercise and its elements. The paper provides examples of the use of video technologies in archers’ training practice. Conclusions: Prospects of the use of the state-of-the-art computer technologies in sports training are infinite. Computer software and hardware systems should be available for most coaches. The task of the latter is to learn to use and implement them for the benefit of themselves and athletes. The task of the scientific groups and experts is to find a most convenient way for the coach to use the innovative technologies. The task of the software developer is to model intellectual programs to help the coach effectively analyze and evaluate his archers or team when preparing them for the most

  15. 26 CFR 1.25-4T - Qualified mortgage credit certificate program (Temporary).

    Science.gov (United States)

    2010-04-01

    ... designed to ensure that only those individuals who could not otherwise purchase a residence will benefit... may be issued in connection with the qualified rehabilitation of a residence part of the cost of which... surrendered to other issuers during the calendar year, (v) The date and amount of any previous elections under...

  16. Wanted, A National Teacher Supply Policy for Education:The Right Way to Meet The "Highly Qualified Teacher" Challenge

    Directory of Open Access Journals (Sweden)

    Linda Darling-Hammond

    2003-09-01

    Full Text Available Teacher quality is now the focus of unprecedented policy analysis. To achieve its goals, the No Child Left Behind Act (NCLB requires a “highly qualified teacher” in all classrooms. The concern with teacher quality has been driven by a growing recognition, fueled by accumulating research evidence, of how critical teachers are to student learning. To acquire and retain high-quality teachers in our Nation’s classrooms will require substantial policy change at many levels. There exists longstanding precedent and strong justification for Washington to create a major education manpower program. Qualified teachers are a critical national resource that requires federal investment and cross-state coordination as well as other state and local action. NCLB provides a standard for equitable access to teacher quality that is both reasonable and feasible. Achieving this goal will require a new vision of the teacher labor market and the framing of a national teacher supply policy. States and local districts have vital roles to play in ensuring a supply of highly qualified teachers; however, they must be supported by appropriate national programs. These programs should be modeled on U.S. medical manpower efforts, which have long supplied doctors to high- need communities and eased shortages in specific health fields. We argue that teacher supply policy should attract well-prepared teachers to districts that sorely need them while relieving shortages in fields like special education, math and the physical sciences. We study the mal-distribution of teachers and examine its causes. We describe examples of both states and local school districts that have fashioned successful strategies for strengthening their teaching forces. Unfortunately, highly successful state and local program to meet the demand for qualified teachers are the exception rather than the rule. They stand out amid widespread use of under-prepared teachers and untrained aides, mainly for

  17. Newer polyanionic bio-composite anode for sodium ion batteries

    Science.gov (United States)

    Karuppiah, Saravanan; Vellingiri, Suganya; Nallathamby, Kalaiselvi

    2017-02-01

    NASICON frame work Na3V2(PO4)3 (NVP), wrapped by nitrogen and sulfur doped bio-carbon matrix derived from human hair (HHC) has been investigated for its anode behavior in SIBs. Basically, NVP is bestowed with a crystal structure of 3D open framework and a moderate theoretical capacity of 118 mAh g-1, which are the twin advantages and motivation behind the selection of this material. Prepared through a simple, scalable and facile method, the key problems associated with pristine NVP electrode material, such as inferior conductivity and severe volume change have been mitigated to a great extent through the formation of a composite containing HHC. Herein, HHC is a cheap and eco-friendly composite additive, obtained from a universal bio-waste, viz., human hair and hence NVP/HHC qualifies itself as a green composite. Interestingly, NVP/HHC-10 (in-situ) and NVP/HHC-20 (ex-situ) anodes show excellent electrochemical performance in terms of cycling stability up to 500 cycles and rate capability @ 2 A g-1, which are superior than similar category NVP anodes reported in the literature. Further, post cycling structure and morphology of NVP/HHC composite anodes evidence the appreciable stability bestowed with the select composition, which is found to get maintained upon extended cycles and even after rate capability test.

  18. 40 CFR 35.4190 - How does my group identify a qualified technical advisor?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false How does my group identify a qualified technical advisor? 35.4190 Section 35.4190 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS...: (1) Demonstrated knowledge of hazardous or toxic waste issues, relocation issues, redevelopment...

  19. 38 CFR 21.6519 - Eligibility of qualified veterans for employment and counseling services.

    Science.gov (United States)

    2010-07-01

    ... veterans for employment and counseling services. 21.6519 Section 21.6519 Pensions, Bonuses, and Veterans... employment and counseling services. (a) General. A qualified veteran for whom vocational rehabilitation and achievenment of a vocational goal are reasonably feasible may be provided the employment and counseling...

  20. The Electromagnetic and Mechanical Properties of Structural Composites: A Theoretical and Experimental Design Study

    Science.gov (United States)

    2014-08-22

    use a large variety of structural grade woven fabrics. These fabrics vary in fiber type (e.g. glass, carbon, kevlar or aramid), thickness, weight and...polymer resin (e.g. thermosets such as epoxy , vinyl ester or polyester) to create a FRP structure that satisfies the mechanical requirements of the...two were a single ply of the same woven fabrics infused with an epoxy vinyl ester resin (Derakane 510A) and cured. To create the infused samples, we