WorldWideScience

Sample records for quad cities-1 reactor

  1. Analysis of cracked core spray piping from the Quad Cities Unit 2 boiling water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Diercks, D.R.; Gaitonde, S.M.

    1982-09-01

    The results of a metallurgical analysis of leaking cracks detected in the core spray injection piping of Commonwealth Edison Company's Quad Cities Unit 2 Boiling Water Reactor are described. The cracks were present in a welded 105/sup 0/ elbow assembly in the line, and were found to be caused by intergranular stress corrosion cracking associated with the probable presence of dissolved oxygen in the reactor cooling water and the presence of grain boundary sensitization and local residual stresses induced by welding. The failure is unusual in several respects, including the very large number of cracks (approximately 40) present in the failed component, the axial orientation of the cracks, and the fact that at least one crack completely penetrated a circumferential weld. Virtually all of the cracking occurred in forged material, and the microstructural evidence presented suggests that the orientation of the cracks was influenced by the presence of axially banded delta ferrite in the microstructure of the forged components.

  2. Calculation of Quad-Cities Central Bundle Documented by the U.S. in FY98 Using Russian Computer Codes

    Energy Technology Data Exchange (ETDEWEB)

    Pavlovichev, A.M.

    2001-06-19

    The report presents calculation results of isotopic composition of irradiated fuel performed for the Quad Cities-1 reactor bundle with UO{sub 2} and MOX fuel. The MCU-REA code was used for calculations. The code is developed in Kurchatov Institute, Russia. The MCU-REA results are compared with the experimental data and HELIOS code results.

  3. Analysis of cracked core spray injection line piping from the Quad Cities Units 1 and 2 boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Diercks, D.R.

    1983-12-01

    Elbow assemblies and adjacent piping from the loops A and B core spray injection lines of Quad Cities Units 1 and 2 Boiling Water Reactors have been examined in order to determine the nature and causes of coolant leakages and flaw indications detected during hydrostatic tests and subsequent ultrasonic inspections. The elbow assemblies were found to contain multiple intergranular cracks in the weld heat-affected zones. The cracking was predominantly axial in orientation in the forged elbow and wedge components, whereas mixed axial and circumferential cracking was seen in the wrought piping pieces. In at least two instances, axial cracks completely penetrated the circumferential weld joining adjacent components. Based upon the observations made in the present study, the failures were attributed to intergranular stress corrosion cracking caused by the weld-induced sensitized microstructure and residual stresses present; dissolved oxygen in the reactor coolant apparently served as the corrosive species. The predominantly axial orientation of the cracks present in the forged components is believed to be related to the banded microstructure present in these components. The metallographic studies reported are supplemented by x-radiography, chemical analysis and mechanical test results, determinations of the degree of sensitization present, and measurements of weld metal delta ferrite content.

  4. Silver City 1:100000 Quad Transportation DLGs

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — Digital line graph (DLG) data are digital representations of cartographic information. DLG's of map features are converted to digital form from maps and related...

  5. Silver City 1:100000 Quad Hydrography DLGs

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — Digital line graph (DLG) data are digital representations of cartographic information. DLG's of map features are converted to digital form from maps and related...

  6. Reactors

    CERN Document Server

    International Electrotechnical Commission. Geneva

    1988-01-01

    This standard applies to the following types of reactors: shunt reactors, current-limiting reactors including neutral-earthing reactors, damping reactors, tuning (filter) reactors, earthing transformers (neutral couplers), arc-suppression reactors, smoothing reactors, with the exception of the following reactors: small reactors with a rating generally less than 2 kvar single-phase and 10 kvar three-phase, reactors for special purposes such as high-frequency line traps or reactors mounted on rolling stock.

  7. Status of the QUAD Experiment

    Science.gov (United States)

    Church, Sarah

    2006-12-01

    The QUaD (QUEST at DASI) experiment comprises a 31-pixel polarization-sensitive bolometric camera mounted on a 2.6m telescope at the South Pole. QUaD has completed two seasons of observations designed to measure the polarization of the Cosmic Microwave Background (CMB). I will report on the status of QUaD data analysis and interpretation. QUaD is a collaboration between institutions in the US, the UK and Ireland and is funded by the NSF, PPARC and Enterprise Ireland.

  8. USGS Digital Orthophoto Quad (DOQ) Metadata

    Data.gov (United States)

    Minnesota Department of Natural Resources — Metadata for the USGS DOQ Orthophoto Layer. Each orthophoto is represented by a Quarter 24k Quad tile polygon. The polygon attributes contain the quarter-quad tile...

  9. USGS Digital Orthophoto Quad (DOQ) - 3 meter

    Data.gov (United States)

    Minnesota Department of Natural Resources — These data files are a collection of the USGS standard DOQs that have been resampled to a 3-meter cell resolution and mosaiced into quad format vs quarter quad...

  10. Report on the QUaD Experiment

    Science.gov (United States)

    Hinderks, James

    2007-05-01

    The QUaD (QUEST at DASI) experiment is a millimeter-wave polarimeter designed to probe the cosmic microwave background (CMB) polarization over a multipole range of 100 to 2500. QUaD observes the CMB with an array of 31 polarization-sensitive bolometers split between two frequency bands centered at 100 and 150 GHz. The telescope is a 2.6 m on-axis Cassegrain design with beam sizes of 6.3' and 4.2' at the two respective observing frequencies. QUaD was commissioned at the South Pole in the Austral summer of 2004/2005. It has since completed two full seasons of observations with a third season underway. I will report on the status of QUaD observations and analysis. QUaD is a collaboration between institutions in the US, the UK and Ireland and is funded by the NSF, PPARC and Enterprise Ireland.

  11. Mount Isa statement on quad bike safety.

    Science.gov (United States)

    Franklin, Richard C; Knight, Sabina; Lower, Tony

    2014-01-01

    Quad bikes are the leading cause of death in Australian agriculture, with half of these deaths resulting from rollovers. Between 2001 and 2012, there were more than 160 such deaths in Australia, representing a significant burden. There is a diversity of public opinions offered about quad bike safety. The Are You Remotely Interested … in Prevention; Building a Culture of Safety conference held in Mount Isa, Queensland, in August 2012 brought together subject matter experts from across Australia to discuss a range of issues relevant to rural Australia (including quad bikes). During this conference, the Mount Isa Statement for Quad Bike Safety was produced. The intent of the Statement was to draw on existing evidence to highlight solutions and provide a direction for future efforts to reduce the burden of death and injury related to quad bike use. The conference provided an opportunity for those with an interest in quad bike safety to come together in one location, discuss the issues and develop a common direction (the Statement). The Statement is presented in three sections: a statement of the facts that were available at the time of development; a set of recommendations; and what needs to happen next. We believe to the best of our knowledge this is the first time where many potential solutions for keeping people safe while operating quad bikes in agriculture have been explored in a public forum. There are some immediate solutions that people can undertake to keep themselves and those in their care safe when using a quad bike: initially selecting safer vehicles to use; fitting quad bikes with crush protection devices; not carrying passengers or overloading the quads; and wearing helmets.

  12. Quad-Bike Operational Instability

    Directory of Open Access Journals (Sweden)

    Ross H. Macmillan

    2017-05-01

    Full Text Available The stake-holders in the quad-bike (QB industry in Australia have failed to reach a satisfactory resolution of the present impasse that exists with respect to the causes and mitigation of the trauma suffered by riders due to QB instability. In an effort to provide purchasers with data enabling them to discriminate between safer and less safe machines, static longitudinal and lateral tests have been conducted by various interested parties; quasi-static lateral tests have also been conducted under some operational conditions. It is argued that while these static tests are valid, under many operating conditions QBs will not reach such unstable slopes due to poor traction. Further, these tests do not include the quasi-static and dynamic factors which also influence the processes associated with operational instability. For these reasons, the static tests do not provide an adequate basis for discrimination between safer and less safe machines.

  13. Reactor

    Science.gov (United States)

    Evans, Robert M.

    1976-10-05

    1. A neutronic reactor having a moderator, coolant tubes traversing the moderator from an inlet end to an outlet end, bodies of material fissionable by neutrons of thermal energy disposed within the coolant tubes, and means for circulating water through said coolant tubes characterized by the improved construction wherein the coolant tubes are constructed of aluminum having an outer diameter of 1.729 inches and a wall thickness of 0.059 inch, and the means for circulating a liquid coolant through the tubes includes a source of water at a pressure of approximately 350 pounds per square inch connected to the inlet end of the tubes, and said construction including a pressure reducing orifice disposed at the inlet ends of the tubes reducing the pressure of the water by approximately 150 pounds per square inch.

  14. Connectivity editing for quad-dominant meshes

    KAUST Repository

    Peng, Chihan

    2013-08-01

    We propose a connectivity editing framework for quad-dominant meshes. In our framework, the user can edit the mesh connectivity to control the location, type, and number of irregular vertices (with more or fewer than four neighbors) and irregular faces (non-quads). We provide a theoretical analysis of the problem, discuss what edits are possible and impossible, and describe how to implement an editing framework that realizes all possible editing operations. In the results, we show example edits and illustrate the advantages and disadvantages of different strategies for quad-dominant mesh design. © 2013 The Author(s) Computer Graphics Forum © 2013 The Eurographics Association and John Wiley & Sons Ltd.

  15. A novel bit-quad-based Euler number computing algorithm.

    Science.gov (United States)

    Yao, Bin; He, Lifeng; Kang, Shiying; Chao, Yuyan; Zhao, Xiao

    2015-01-01

    The Euler number of a binary image is an important topological property in computer vision and pattern recognition. This paper proposes a novel bit-quad-based Euler number computing algorithm. Based on graph theory and analysis on bit-quad patterns, our algorithm only needs to count two bit-quad patterns. Moreover, by use of the information obtained during processing the previous bit-quad, the average number of pixels to be checked for processing a bit-quad is only 1.75. Experimental results demonstrated that our method outperforms significantly conventional Euler number computing algorithms.

  16. A novel bit-quad-based Euler number computing algorithm

    OpenAIRE

    Yao, Bin; He, Lifeng; Kang, Shiying; Chao, Yuyan; Xiao ZHAO

    2015-01-01

    The Euler number of a binary image is an important topological property in computer vision and pattern recognition. This paper proposes a novel bit-quad-based Euler number computing algorithm. Based on graph theory and analysis on bit-quad patterns, our algorithm only needs to count two bit-quad patterns. Moreover, by use of the information obtained during processing the previous bit-quad, the average number of pixels to be checked for processing a bit-quad is only 1.75. Experimental results ...

  17. QUAD METHOD FOR IDENTIFYING RELATIVELY STABLE STATIONS

    Institute of Scientific and Technical Information of China (English)

    HuangLiren

    2003-01-01

    The QUAD(Quasi-Accurate Detection of gross errors) method which is originally developed to detect gross errors in the geodetic data is extended and used to select and indentify relatively stable stations. The formulas and algorithm are described in detail. Some problems that should be noticed in the use of this method are discussed. Finally, this method is applied to some data observed in North China as an example.

  18. QUAD METHOD FOR IDENTIFYING RELATIVELY STABLE STATIONS

    Institute of Scientific and Technical Information of China (English)

    Huang Liren

    2003-01-01

    The QUAD(Quasi-Accurate Detection of gross errors) method which is originally developed to detect gross errors in the geodetic data is extended and used to select and identify relatively stable stations. The formulas and algorithm are described in detail. Some problems that should be noticed in the use of this method are discussed. Finally, this method is applied to some data observed in North China as an example.

  19. Benchmarking the QUAD4/TRIA3 element

    Science.gov (United States)

    Pitrof, Stephen M.; Venkayya, Vipperla B.

    1993-01-01

    The QUAD4 and TRIA3 elements are the primary plate/shell elements in NASTRAN. These elements enable the user to analyze thin plate/shell structures for membrane, bending and shear phenomena. They are also very new elements in the NASTRAN library. These elements are extremely versatile and constitute a substantially enhanced analysis capability in NASTRAN. However, with the versatility comes the burden of understanding a myriad of modeling implications and their effect on accuracy and analysis quality. The validity of many aspects of these elements were established through a series of benchmark problem results and comparison with those available in the literature and obtained from other programs like MSC/NASTRAN and CSAR/NASTRAN. Never-the-less such a comparison is never complete because of the new and creative use of these elements in complex modeling situations. One of the important features of QUAD4 and TRIA3 elements is the offset capability which allows the midsurface of the plate to be noncoincident with the surface of the grid points. None of the previous elements, with the exception of bar (beam), has this capability. The offset capability played a crucial role in the design of QUAD4 and TRIA3 elements. It allowed modeling layered composites, laminated plates and sandwich plates with the metal and composite face sheets. Even though the basic implementation of the offset capability is found to be sound in the previous applications, there is some uncertainty in relatively simple applications. The main purpose of this paper is to test the integrity of the offset capability and provide guidelines for its effective use. For the purpose of simplicity, references in this paper to the QUAD4 element will also include the TRIA3 element.

  20. Quad-rotor flight path energy optimization

    Science.gov (United States)

    Kemper, Edward

    Quad-Rotor unmanned areal vehicles (UAVs) have been a popular area of research and development in the last decade, especially with the advent of affordable microcontrollers like the MSP 430 and the Raspberry Pi. Path-Energy Optimization is an area that is well developed for linear systems. In this thesis, this idea of path-energy optimization is extended to the nonlinear model of the Quad-rotor UAV. The classical optimization technique is adapted to the nonlinear model that is derived for the problem at hand, coming up with a set of partial differential equations and boundary value conditions to solve these equations. Then, different techniques to implement energy optimization algorithms are tested using simulations in Python. First, a purely nonlinear approach is used. This method is shown to be computationally intensive, with no practical solution available in a reasonable amount of time. Second, heuristic techniques to minimize the energy of the flight path are tested, using Ziegler-Nichols' proportional integral derivative (PID) controller tuning technique. Finally, a brute force look-up table based PID controller is used. Simulation results of the heuristic method show that both reliable control of the system and path-energy optimization are achieved in a reasonable amount of time.

  1. 6K Quads for ER Reference, US, EPA, SEGS

    Data.gov (United States)

    U.S. Environmental Protection Agency — This dynamic web map service contains reference quads for emergency response reconnaissance developed for use by the US Environmental Protection Agency. Grid cells...

  2. Constructing C1 Continuous Surface on Irregular Quad Meshes

    Institute of Scientific and Technical Information of China (English)

    HE Jun; GUO Qiang

    2013-01-01

    A new method is proposed for surface construction on irregular quad meshes as extensions to uniform B-spline surfaces. Given a number of control points, which form a regular or irregular quad mesh, a weight function is constructed for each control point. The weight function is defined on a local domain and is C1 continuous. Then the whole surface is constructed by the weighted combination of all the control points. The property of the new method is that the surface is defined by piecewise C1 bi-cubic rational parametric polynomial with each quad face. It is an extension to uniform B-spline surfaces in the sense that its definition is an analogy of the B-spline surface, and it produces a uniform bi-cubic B-spline surface if the control mesh is a regular quad mesh. Examples produced by the new method are also included.

  3. Mathematical Modelling of Translation and Rotation Movement in Quad Tiltrotor

    Directory of Open Access Journals (Sweden)

    Andi Dharmawan

    2017-06-01

    Full Text Available Quadrotor as one type of UAV (Unmanned Aerial Vehicle is an underactuated mechanical system. It means that the system has some control inputs is lower than its DOF (Degrees of Freedom. This condition causes quadrotor to have limited mobility because of its inherent under actuation, namely, the availability of four independent control signals (four-speed rotating propellers versus 6 degrees of freedom parameterizing quadrotor position or orientation in space. If a quadrotor is made to have 6 DOF, a full motion control system to optimize the flight will be different from before. So it becomes necessary to develop over actuated quad tiltrotor. Quad tiltrotor has control signals more than its DOF. Therefore, we can refer it to the overactuated system. We need a good control system to fly the quad tiltrotor. Good control systems can be designed using the model of the quad tiltrotor system. We can create quad tiltrotor model using its dynamics based on Newton-Euler approach. After we have a set of model, we can simulate the control system using some control method. There are several control methods that we can use in the quad tiltrotor flight system. However, we can improve the control by implementing a modern control system that uses the concept of state space. The simulations show that the quad tiltrotor has done successful translational motion without significant interference. Also, undesirable rotation movement in the quad tiltrotor flight when performing the translational motions resulting from the transition process associated with the tilt rotor change was successfully reduced below 1 degree.

  4. Quad Rotorcraft Control Vision-Based Hovering and Navigation

    CERN Document Server

    García Carrillo, Luis Rodolfo; Lozano, Rogelio; Pégard, Claude

    2013-01-01

    Quad-Rotor Control develops original control methods for the navigation and hovering flight of an autonomous mini-quad-rotor robotic helicopter. These methods use an imaging system and a combination of inertial and altitude sensors to localize and guide the movement of the unmanned aerial vehicle relative to its immediate environment. The history, classification and applications of UAVs are introduced, followed by a description of modelling techniques for quad-rotors and the experimental platform itself. A control strategy for the improvement of attitude stabilization in quad-rotors is then proposed and tested in real-time experiments. The strategy, based on the use of low-cost components and with experimentally-established robustness, avoids drift in the UAV’s angular position by the addition of an internal control loop to each electronic speed controller ensuring that, during hovering flight, all four motors turn at almost the same speed. The quad-rotor’s Euler angles being very close to the origin, oth...

  5. Cosmological Parameters from the QUaD CMB polarization experiment

    CERN Document Server

    Ade, P; Bowden, M; Brown, M L; Cahill, G; Church, S; Culverhouse, T; Friedman, R B; Ganga, K; Gear, W K; Gupta, S; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; Pryke, C; Schwarz, R; O'Sullivan, C; Piccirillo, L; Rajguru, N; Rusholme, B; Taylor, A N; Thompson, K L; Turner, A H; Wu, E Y S; Zemcov, M

    2009-01-01

    In this paper we present a parameter estimation analysis of the polarization and temperature power spectra from the second and third season of observations with the QUaD experiment. QUaD has for the first time detected multiple acoustic peaks in the E-mode polarization spectrum with high significance. Although QUaD-only parameter constraints are not competitive with previous results for the standard 6-parameter LCDM cosmology, they do allow meaningful polarization-only parameter analyses for the first time. In a standard 6-parameter LCDM analysis we find the QUaD TT power spectrum to be in good agreement with previous results. However, the QUaD polarization data shows some tension with LCDM. The origin of this 1 to 2 sigma tension remains unclear, and may point to new physics, residual systematics or simple random chance. We also combine QUaD with the five-year WMAP data set and the SDSS Luminous Red Galaxies 4th data release power spectrum, and extend our analysis to constrain individual isocurvature mode fr...

  6. The Quad Council practice competencies for public health nursing.

    Science.gov (United States)

    Swider, Susan M; Krothe, Joyce; Reyes, David; Cravetz, Michelle

    2013-01-01

    This article describes the most recent efforts by the Quad Council of Public Health Nursing organizations to review and revise the competencies for PHN practice, and highlights the implications of these competencies for practice, education, and research. The Quad Council is a coalition of four nursing organizations with a focus on public health nursing and includes the Association of Community Health Nursing Educators; the Association of Public Health Nursing (known prior to July 1, 2012 as the Association of State and Territorial Directors of Nursing); the Public Health Nursing section of the American Public Health Association; and the Council on Economics and Practice of the American Nurses' Association. The Quad Council competencies are based on the Council on Linkages competencies for public health professionals and were designed to ensure that public health nursing fits in the domain of public health science and practice.

  7. Cosmological Parameters From the Quad Cmb Polarization Experiment

    OpenAIRE

    Castro, P.G. (Patricia Garrido); Ade, P.; Bock, J.; Bowden, M.; Brown, M L; Cahill, G.; Church, S.; Culverhouse, T.; Friedman, R. B.; Ganga, K.; Gear, W.K.; S. Gupta; Hinderks, J.; Kovac, John M.; Lange, A. E.

    2009-01-01

    In this paper, we present a parameter estimation analysis of the polarization and temperature power spectra from the second and third season of observations with the QUaD experiment. QUaD has for the first time detected multiple acoustic peaks in the E-mode polarization spectrum with high significance. Although QUaD-only parameter constraints are not competitive with previous results for the standard six-parameter ΛCDM cosmology, they do allow meaningful polarization-only parameter analyses f...

  8. Quad-Quaternion MUSIC for DOA Estimation Using Electromagnetic Vector Sensors

    Directory of Open Access Journals (Sweden)

    Xiaofeng Gong

    2008-01-01

    Full Text Available A new quad-quaternion model is herein established for an electromagnetic vector-sensor array, under which a multidimensional algebra-based direction-of-arrival (DOA estimation algorithm, termed as quad-quaternion MUSIC (QQ-MUSIC, is proposed. This method provides DOA estimation (decoupled from polarization by exploiting the orthogonality of the newly defined “quad-quaternion” signal and noise subspaces. Due to the stronger constraints that quad-quaternion orthogonality imposes on quad-quaternion vectors, QQ-MUSIC is shown to offer high robustness to model errors, and thus is very competent in practice. Simulation results have validated the proposed method.

  9. Nuclear Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hogerton, John

    1964-01-01

    This pamphlet describes how reactors work; discusses reactor design; describes research, teaching, and materials testing reactors; production reactors; reactors for electric power generation; reactors for supply heat; reactors for propulsion; reactors for space; reactor safety; and reactors of tomorrow. The appendix discusses characteristics of U.S. civilian power reactor concepts and lists some of the U.S. reactor power projects, with location, type, capacity, owner, and startup date.

  10. Modeling of Earth's Gravity Fields Visualization Based on Quad Tree

    Institute of Scientific and Technical Information of China (English)

    LUO Zhicai; LI Zhenhai; ZHONG Bo

    2010-01-01

    The problems of the earth's gravity fields' visualization are both focus and puzzle currently. Aiming at multiresolution rendering, modeling of the Earth's gravity fields' data is discussed in the paper by using LOD algorithm based on Quad Tree. First,this paper employed the method of LOD based on Quad Tree to divide up the regional gravity anomaly data, introduced the combined node evaluation system that was composed of viewpoint related and roughness related systems, and then eliminated the T-cracks that appeared among the gravity anomaly data grids with different resolutions. The test results demonstrated that the gravity anomaly data grids' rendering effects were living, and the computational power was low. Therefore, the proposed algorithm was a suitable method for modeling the gravity anomaly data and has potential applications in visualization of the earth's gravity fields.

  11. Physical investigation of a quad confinement plasma source

    Science.gov (United States)

    Knoll, Aaron; Lucca Fabris, Andrea; Young, Christopher; Cappelli, Mark

    2016-10-01

    Quad magnetic confinement plasma sources are novel magnetized DC discharges suitable for applications in a broad range of fields, particularly space propulsion, plasma etching and deposition. These sources contain a square discharge channel with magnetic cusps at the four lateral walls, enhancing plasma confinement and electron residence time inside the device. The magnetic field topology is manipulated using four independent electromagnets on each edge of the channel, tuning the properties of the generated plasma. We characterize the plasma ejected from the quad confinement sources using a combination of traditional electrostatic probes and non-intrusive laser-based diagnostics. Measurements show a strong ion acceleration layer located 8 cm downstream of the exit plane, beyond the extent of the magnetic field. The ion velocity field is investigated with different magnetic configurations, demonstrating how ion trajectories may be manipulated. C.Y. acknowledges support from the DOE NSSA Stewardship Science Graduate Fellowship under contract DE-FC52-08NA28752.

  12. Evaluation of the ETS-Lindgren Open Boundary Quad-Ridged Horn 3164-06

    Science.gov (United States)

    2015-04-01

    Evaluation of the ETS -Lindgren Open Boundary Quad-Ridged Horn 3164-06 by Christopher S Kenyon ARL-TR-7272 April 2015...Evaluation of the ETS -Lindgren Open Boundary Quad-Ridged Horn 3164-06 Christopher S Kenyon Sensors and Electron Devices Directorate, ARL...2014 4. TITLE AND SUBTITLE Evaluation of the ETS -Lindgren Open Boundary Quad-Ridged Horn 3164-06 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM

  13. Development of net energy ratio for quad-generation pathways

    DEFF Research Database (Denmark)

    Rudra, Souman; Rosendahl, Lasse; Kumar, Amit

    2012-01-01

    Institute (GTI) gasifier and Circulating Fluidized Bed (CFB) technologies are used for this quad generation process. Three different biomass feedstocks are considered in this study. The net energy ratio for six different pathways having the range of between 1.3–9.3. The lowest limit corresponds to the straw...... of the production and use of biomass for different outputs based on demand. Finally, we conduct sensitivity analysis for expected technological improvements and factors that could increase the energy performance....

  14. Shape Memory Alloy Isolation Valves: Public Quad Chart

    Science.gov (United States)

    2017-05-12

    NUMBER (Include area code) 12 May 2017 Briefing Charts 12 April 2017 - 12 May 2017 Shape Memory Alloy Isolation Valves: Public Quad Chart William...spacecraft (15+ yrs) • Shaped memory alloy isolation valves provide an intrinsically safe isolation system that increases lifetime >5x over SOTA and... Shape Memory Alloy Isolation Valves POC: W. Hargus, Ph.D., AFRL/RQRC B-52 Teardrop Antenna Depolymerization WC-130J Leading Edge Erosion Distribution

  15. Quad-Rotor Helicopter Autonomous Navigation Based on Vanishing Point Algorithm

    Directory of Open Access Journals (Sweden)

    Jialiang Wang

    2014-01-01

    Full Text Available Quad-rotor helicopter is becoming popular increasingly as they can well implement many flight missions in more challenging environments, with lower risk of damaging itself and its surroundings. They are employed in many applications, from military operations to civilian tasks. Quad-rotor helicopter autonomous navigation based on the vanishing point fast estimation (VPFE algorithm using clustering principle is implemented in this paper. For images collected by the camera of quad-rotor helicopter, the system executes the process of preprocessing of image, deleting noise interference, edge extracting using Canny operator, and extracting straight lines by randomized hough transformation (RHT method. Then system obtains the position of vanishing point and regards it as destination point and finally controls the autonomous navigation of the quad-rotor helicopter by continuous modification according to the calculated navigation error. The experimental results show that the quad-rotor helicopter can implement the destination navigation well in the indoor environment.

  16. General Motors 2. 3L Quad 4 engine

    Energy Technology Data Exchange (ETDEWEB)

    Thomson, M.W.; Frelund, A.R.; Pallas, M.; Miller, K.D.

    1987-01-01

    For the 1988 model year General Motors will introduce a new 2.3L, four cylinder, 16 valve engine named the ''Quad 4''. This engine features high specific power, low mechanical and thermal losses, precision manufacturing processes, and outstanding reliability. This paper describes the organizational and operating philosophies including simultaneous engineering and supplier source selection and development under which this engine was designed, processed, validated, and manufactured. Also described are the design features and manufacturing techniques utilized to reach the program objectives.

  17. On multidimensional consistent systems of asymmetric quad-equations

    CERN Document Server

    Boll, Raphael

    2012-01-01

    Multidimensional Consistency becomes more and more important in the theory of discrete integrable systems. Recently, we gave a classification of all 3D consistent 6-tuples of equations with the tetrahedron property, where several novel asymmetric systems have been found. In the present paper we discuss higher-dimensional consistency for 3D consistent systems coming up with this classification. In addition, we will give a classification of certain 4D consistent systems of quad-equations. The results of this paper allow for a proof of the Bianchi permutability among other applications.

  18. Advanced Automatic Hexahedral Mesh Generation from Surface Quad Meshes

    OpenAIRE

    Kremer, Michael; Bommes, David; Lim, Isaak; Kobbelt, Leif

    2013-01-01

    International audience; A purely topological approach for the generation of hexahedral meshes from quadrilateral surface meshes of genus zero has been proposed by M. Müller-Hannemann: in a first stage, the input surface mesh is reduced to a single hexahedron by successively eliminating loops from the dual graph of the quad mesh; in the second stage, the hexahedral mesh is constructed by extruding a layer of hexahedra for each dual loop from the first stage in reverse elimination order. In th...

  19. H Reactor

    Data.gov (United States)

    Federal Laboratory Consortium — The H Reactor was the first reactor to be built at Hanford after World War II.It became operational in October of 1949, and represented the fourth nuclear reactor on...

  20. Performance of an MPI-only semiconductor device simulator on a quad socket/quad core InfiniBand platform.

    Energy Technology Data Exchange (ETDEWEB)

    Shadid, John Nicolas; Lin, Paul Tinphone

    2009-01-01

    This preliminary study considers the scaling and performance of a finite element (FE) semiconductor device simulator on a capacity cluster with 272 compute nodes based on a homogeneous multicore node architecture utilizing 16 cores. The inter-node communication backbone for this Tri-Lab Linux Capacity Cluster (TLCC) machine is comprised of an InfiniBand interconnect. The nonuniform memory access (NUMA) nodes consist of 2.2 GHz quad socket/quad core AMD Opteron processors. The performance results for this study are obtained with a FE semiconductor device simulation code (Charon) that is based on a fully-coupled Newton-Krylov solver with domain decomposition and multilevel preconditioners. Scaling and multicore performance results are presented for large-scale problems of 100+ million unknowns on up to 4096 cores. A parallel scaling comparison is also presented with the Cray XT3/4 Red Storm capability platform. The results indicate that an MPI-only programming model for utilizing the multicore nodes is reasonably efficient on all 16 cores per compute node. However, the results also indicated that the multilevel preconditioner, which is critical for large-scale capability type simulations, scales better on the Red Storm machine than the TLCC machine.

  1. Quad-helix用于前方牵引的支抗控制

    Institute of Scientific and Technical Information of China (English)

    左艳萍; 陈文静; 刘学聪

    2002-01-01

    @@ Quad-helix由Ricketts医师设计发明一直在正畸临床用于扩大后牙弓宽度.我们在伴有上牙弓宽度不足的Ⅲ类病人先用quad-helix扩大后牙弓,建立后牙的覆覆盖关系,然后考虑到支抗的问题,通过将Quad-helix改良,继续用于前方牵引,取得了满意的效果,且简化了治疗.现介绍如下.

  2. Novel quad-band terahertz metamaterial absorber based on single pattern U-shaped resonator

    Science.gov (United States)

    Wang, Ben-Xin; Wang, Gui-Zhen

    2017-03-01

    A novel quad-band terahertz metamaterial absorber using four different modes of single pattern resonator is demonstrated. Four obvious frequencies with near-perfect absorption are realized. Near-field distributions of the four modes are provided to reveal the physical picture of the multiple-band absorption. Unlike most previous quad-band absorbers that typically require four or more patterns, the designed absorber has only one resonant structure, which is simpler than previous works. The presented quad-band absorber has potential applications in biological sensing, medical imaging, and material detection.

  3. QuadCam机器成像安全设备

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    近日.豪迈集团旗下子公司之一——Castell安全国际有限公司公布了其新开发的QuadCam 3D成像设备。依托复杂的3D成像技术,该产品为用户提供了无比的安全性。相对于传统的安全封盖、栅栏或安全门等安全设备.该产品有着非常明显的优势:反应时间短.且提供的安全范围更大。

  4. Quad-Band U-Slot Antenna for Mobile Applications

    Directory of Open Access Journals (Sweden)

    R. L. Ruiz

    2006-06-01

    Full Text Available In this paper, two different planar quad-band antennas are designed, modeled, fabricated and measured. Subsequently, the antennas are redesigned using an electromagnetic band gap substrate (EBG. Those new planar antennas operate in four frequency bands: 900 MHz, 1 800 MHz (both GSM, 1 900 MHz (USA and 2 400 to 2 500 MHz (Bluetooth The antenna has four narrow U-shaped slots etched to the patch. Using software, CST Microwave Studio [1], Zeland IE3D [2], and FEMLAB [3], simulations have been carried out to investigate the antenna's performance and characteristics. The antennas designed have been also built and measured to compare the real results with those obtained from the simulations.

  5. Production of accelerating quad Airy beams and their optical characteristics.

    Science.gov (United States)

    Ren, Zhijun; Wu, Qiong; Shi, Yile; Chen, Chen; Wu, Jiangmiao; Wang, Hui

    2014-06-16

    Based on a geometric caustic argument and diffraction catastrophe theory, we generate a novel form of accelerating beams using a symmetric 3/2 phase-only pattern. Such beams can be called accelerating quad Airy beams (AQABs) because they look very much like four face-to-face combined Airy beams. Optical characteristics of AQABs are subsequently investigated. The research results show that the beams have axial-symmetrical and centrosymmetrical transverse intensity patterns and quasi-diffraction-free propagation features for their four main lobes while undergoing transverse shift along parabolic trajectories. Moreover, we also demonstrate that AQABs possess self-construction ability when local areas are blocked. The unique optical properties of these beams will make them useful tools for future scientific applications.

  6. Dynamic modeling and nonlinear control strategy for an underactuated quad rotor rotorcraft

    Institute of Scientific and Technical Information of China (English)

    Ashfaq Ahmad MIAN; Dao-bo WANG

    2008-01-01

    In this paper, a nonlinear dynamic MIMO model of a 6-DOF underactuated quad rotor rotorcraft is derived based on Newton-Euler formalism. The derivation comprises determining equations of motion of the quad rotor in three dimensions and seeking to approximate the actuation forces through modeling of the aerodynamic coefficients and electric motor dynamics. The derived model is dynamically unstable, so a sequential nonlinear control strategy is implemented for the quad rotor. The control strategy includes exact feedback linearization technique, using the geometric methods of nonlinear control. The performance of the nonlinear control algorithm is evaluated using simulation and the results show the effectiveness of the proposed control strategy for the quad rotor rotorcraft near quasi-stationary flight.

  7. Ultra-Low Noise Quad Photoreceiver for Space Based Laser Interferometric Gravity Wave Detection Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design and develop 2x2 quad p-i-n InGaAs Photoreceivers having the following characteristics: (a) Active area diameter 0.75 mm; (b) Wavelength coverage...

  8. Assessment of vertical changes during maxillary expansion using quad helix or bonded rapid maxillary expander.

    Science.gov (United States)

    Conroy-Piskai, Cara; Galang-Boquiren, Maria Therese S; Obrez, Ales; Viana, Maria Grace Costa; Oppermann, Nelson; Sanchez, Flavio; Edgren, Bradford; Kusnoto, Budi

    2016-11-01

    To determine if there is a significantly different effect on vertical changes during phase I palatal expansion treatment using a quad helix and a bonded rapid maxillary expander in growing skeletal Class I and Class II patients. This retrospective study looked at 2 treatment groups, a quad helix group and a bonded rapid maxillary expander group, before treatment (T1) and at the completion of phase I treatment (T2). Each treatment group was compared to an untreated predicted growth model. Lateral cephalograms at T1 and T2 were traced and analyzed for changes in vertical dimension. No differences were found between the treatment groups at T1, but significant differences at T2 were found for convexity, lower facial height, total facial height, facial axis, and Frankfort Mandibular Plane Angle (FMA) variables. A comparison of treatment groups at T2 to their respective untreated predicted growth models found a significant difference for the lower facial height variable in the quad helix group and for the upper first molar to palatal plane (U6-PP) variable in the bonded expander group. Overall, both the quad helix expander and the bonded rapid maxillary expander showed minimal vertical changes during palatal expansion treatment. The differences at T2 suggested that the quad helix expander had more control over skeletal vertical measurements. When comparing treatment results to untreated predicted growth values, the quad helix expander appeared to better maintain lower facial height and the bonded rapid maxillary expander appeared to better maintain the maxillary first molar vertical height.

  9. Reactor Physics

    Energy Technology Data Exchange (ETDEWEB)

    Ait Abderrahim, A

    2001-04-01

    The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised.

  10. Reactor safeguards

    CERN Document Server

    Russell, Charles R

    1962-01-01

    Reactor Safeguards provides information for all who are interested in the subject of reactor safeguards. Much of the material is descriptive although some sections are written for the engineer or physicist directly concerned with hazards analysis or site selection problems. The book opens with an introductory chapter on radiation hazards, the construction of nuclear reactors, safety issues, and the operation of nuclear reactors. This is followed by separate chapters that discuss radioactive materials, reactor kinetics, control and safety systems, containment, safety features for water reactor

  11. Reactor operation

    CERN Document Server

    Shaw, J

    2013-01-01

    Reactor Operation covers the theoretical aspects and design information of nuclear reactors. This book is composed of nine chapters that also consider their control, calibration, and experimentation.The opening chapters present the general problems of reactor operation and the principles of reactor control and operation. The succeeding chapters deal with the instrumentation, start-up, pre-commissioning, and physical experiments of nuclear reactors. The remaining chapters are devoted to the control rod calibrations and temperature coefficient measurements in the reactor. These chapters also exp

  12. Novel Algorithms in Synchronized Quad-Antenna GNSS and INS Tightly-Coupled Combination

    Science.gov (United States)

    Yu, Chao; Chen, Wen; Dong, Danan; Cao, Jie; Cai, Miaomiao; Wang, Zhiren

    2017-04-01

    In this contribution, several novel algorithms in synchronized quad-antenna GNSS and INS tightly-coupled combination was researched and simulated for high precision positioning and attitude determination. For the sake of improving the performance of positioning and attitude determination in urban canyon, a tightly-coupled combination of synchronized quad-antenna GNSS and INS model is established. The traditional double difference (DD) carrier phase observation model can be substituted by single difference (SD) model. As synchronized quad-antenna means four receiving antennas using a common clock, single difference carrier phase observations are no longer contain receiver clock error, and have better performance than the double difference model in view of observation noise, redundancy and parameter correlations. In the SD model, a novel carrier phase ambiguity resolution algorithm named as ambiguity Substitution Approach (ASA) is proposed. It can reduce the ambiguity search range, and enhance the integer ambiguity fixing efficiency. Due to the advantages of synchronized quad-antenna, the real-time multi-baseline adjustment algorithm for attitude determination is researched. In order to realize the high precision positioning and attitude determination using tightly-coupled combination of quad-antenna synchronized GNSS and INS, a modified adaptive Kalman filter (AKF) with fading factor algorithm is developed to merge the GNSS observables and inertial measurements, and the corresponding filter process is described simultaneously. In the end, a MATLAB simulated application is developed to carry out high precision positioning and attitude determination algorithms using quad-antenna synchronized GNSS/INS combination. The experimental results show that decimeter-level positioning and 0.1 degree per 2 meters baseline attitude determination accuracy can be achieved. Keywords: Synchronized, Quad-antenna, GNSS, INS, Tightly-coupled, Combination, Kalman filter, Adaptive

  13. Reactor Neutrinos

    OpenAIRE

    Soo-Bong Kim; Thierry Lasserre; Yifang Wang

    2013-01-01

    We review the status and the results of reactor neutrino experiments. Short-baseline experiments have provided the measurement of the reactor neutrino spectrum, and their interest has been recently revived by the discovery of the reactor antineutrino anomaly, a discrepancy between the reactor neutrino flux state of the art prediction and the measurements at baselines shorter than one kilometer. Middle and long-baseline oscillation experiments at Daya Bay, Double Chooz, and RENO provided very ...

  14. BOILING REACTORS

    Science.gov (United States)

    Untermyer, S.

    1962-04-10

    A boiling reactor having a reactivity which is reduced by an increase in the volume of vaporized coolant therein is described. In this system unvaporized liquid coolant is extracted from the reactor, heat is extracted therefrom, and it is returned to the reactor as sub-cooled liquid coolant. This reduces a portion of the coolant which includes vaporized coolant within the core assembly thereby enhancing the power output of the assembly and rendering the reactor substantially self-regulating. (AEC)

  15. Quad Band Handset Antenna for LTE MIMO and WLAN Application

    Directory of Open Access Journals (Sweden)

    H. S. Wong

    2014-01-01

    Full Text Available A compact quad band antenna for long-term evolution (LTE MIMO and WLAN application in the handset is presented in this paper. The proposed antenna comprises two symmetrical quarter wavelength radiating strips and a slotted ground plane. On the ground plane, a T-shaped slot is cut from the bottom. Two symmetrical P-shaped slots are etched at both sides of the ground plane. The radiating strips and slots generate a lower resonant at 780 MHz and an upper resonant at 2.350 GHz to cover LTE 700 Band 14, LTE 2300, 2.4 GHz WLAN, and LTE 2500. A novel isolation technique by placing a rectangular patch between the radiating strips is presented. The rectangular patch creates a dedicated current path for each radiating strip. The proposed antenna has high isolation of less than −18 dBi at LTE 2300, 2.4 GHz WLAN, and LTE 2500 band.

  16. Cable-Augmented, Quad Ligament Tenodesis Scapholunate Reconstruction.

    Science.gov (United States)

    Bain, Gregory I; Watts, Adam C; McLean, James; Lee, Yu C; Eng, Kevin

    2015-11-01

    Maintaining reduction of the scapholunate interval after reconstruction can be difficult. The authors performed scapholunate reconstruction using tensionable suture anchors in 8 patients. The anchors provide a fixed cable that both fixes the graft, and reduces the scapholunate diastasis and maintains reduction. The flexor carpi radialis tendon graft stabilizes not only the volar scaphotrapezial ligament, and dorsal scapholunate ligament, but also the dorsal intercarpal and dorsal radiocarpal ligament. The Berger flap is closed using an ulnar advancement capsulodesis that further reinforces the dorsal intercarpal and dorsal radiocarpal ligament. The mean pain score improved from 5.8 to 2.1. Mean extension was 56° (91% of contralateral side), flexion 44° (70% of contralateral side), and grip strength was 41kg (95% of the contralateral side). The mean scapholunate angle was 71°, radiolunate angle 16° and scapholunate interval 3.0 mm. The cable augmented, quad ligament scapholunate ligament reconstruction offers theoretical advantages but long term follow up is required.

  17. Quad-phased data mining modeling for dementia diagnosis.

    Science.gov (United States)

    Bang, Sunjoo; Son, Sangjoon; Roh, Hyunwoong; Lee, Jihye; Bae, Sungyun; Lee, Kyungwon; Hong, Changhyung; Shin, Hyunjung

    2017-05-18

    The number of people with dementia is increasing along with people's ageing trend worldwide. Therefore, there are various researches to improve a dementia diagnosis process in the field of computer-aided diagnosis (CAD) technology. The most significant issue is that the evaluation processes by physician which is based on medical information for patients and questionnaire from their guardians are time consuming, subjective and prone to error. This problem can be solved by an overall data mining modeling, which subsidizes an intuitive decision of clinicians. Therefore, in this paper we propose a quad-phased data mining modeling consisting of 4 modules. In Proposer Module, significant diagnostic criteria are selected that are effective for diagnostics. Then in Predictor Module, a model is constructed to predict and diagnose dementia based on a machine learning algorism. To help clinical physicians understand results of the predictive model better, in Descriptor Module, we interpret causes of diagnostics by profiling patient groups. Lastly, in Visualization Module, we provide visualization to effectively explore characteristics of patient groups. The proposed model is applied for CREDOS study which contains clinical data collected from 37 university-affiliated hospitals in republic of Korea from year 2005 to 2013. This research is an intelligent system enabling intuitive collaboration between CAD system and physicians. And also, improved evaluation process is able to effectively reduce time and cost consuming for clinicians and patients.

  18. Escaping Depressions in LRTS Based on Incremental Refinement of Encoded Quad-Trees

    Directory of Open Access Journals (Sweden)

    Yue Hu

    2017-01-01

    Full Text Available In the context of robot navigation, game AI, and so on, real-time search is extensively used to undertake motion planning. Though it satisfies the requirement of quick response to users’ commands and environmental changes, learning real-time search (LRTS suffers from the heuristic depressions where agents behave irrationally. There have introduced several effective solutions, such as state abstractions. This paper combines LRTS and encoded quad-tree abstraction which represent the search space in multiresolutions. When exploring the environments, agents are enabled to locally repair the quad-tree models and incrementally refine the spatial cognition. By virtue of the idea of state aggregation and heuristic generalization, our EQ LRTS (encoded quad-tree based LRTS possesses the ability of quickly escaping from heuristic depressions with less state revisitations. Experiments and analysis show that (a our encoding principle for quad-trees is a much more memory-efficient method than other data structures expressing quad-trees, (b EQ LRTS differs a lot in several characteristics from classical PR LRTS which represent the space and refine the paths hierarchically, and (c EQ LRTS substantially reduces the planning amount and curtails heuristic updates compared with LRTS on uniform cells.

  19. Membrane reactor. Membrane reactor

    Energy Technology Data Exchange (ETDEWEB)

    Shindo, Y.; Wakabayashi, K. (National Chemical Laboratory for Industry, Tsukuba (Japan))

    1990-08-05

    Many reaction examples were introduced of membrane reactor, to be on the point of forming a new region in the field of chemical technology. It is a reactor to exhibit excellent function, by its being installed with membrane therein, and is generally classified into catalyst function type and reaction promotion type. What firstly belongs to the former is stabilized zirconia, where oxygen, supplied to the cathodic side of membrane with voltage, impressed thereon, becomes O {sup 2 {minus}} to be diffused through the membrane and supplied, as variously activated oxygenous species, on the anodic side. Examples with many advantages can be given such as methane coupling, propylene oxidation, methanating reaction of carbon dioxide, etc. Apart, palladium film and naphion film also belong to the former. While examples of the latter comprise, among others, decomposition of hydrogen sulfide by porous glass film and dehydrogenation of cyclohexane or palladium alloy film, which are expected to be developed and materialized in the industry. 33 refs., 8 figs.

  20. Quad-copter UAV BLDC Motor Control: Linear v/s non-linear control maps

    Directory of Open Access Journals (Sweden)

    Deep Parikh

    2015-08-01

    Full Text Available This paper presents some investigations and comparison of using linear versus non-linear static motor-control maps for the speed control of a BLDC (Brush Less Direct Current motors used in quad-copter UAV (Unmanned Aerial Vehicles. The motor-control map considered here is the inverse of the static map relating motor-speed output to motor-voltage input for a typical out-runner type Brushless DC Motors (BLDCM.  Traditionally, quad-copter BLDC motor speed control uses simple linear motor-control map defined by the motor-constant specification. However, practical BLDC motors show non-linear characteristic, particularly when operated across wide operating speed-range as is commonly required in quad-copter UAV flight operations. In this paper, our investigations to compare performance of linear versus non-linear motor-control maps are presented. The investigations cover simulation-based and experimental study of BLDC motor speed control systems for  quad-copter vehicle available. First the non-linear map relating rotor RPM to motor voltage for quad-copter BLDC motor is obtained experimentally using an optical speed encoder. The performance of the linear versus non-linear motor-control-maps for the speed control are studied. The investigations also cover study of time-responses for various standard test input-signals e.g. step, ramp and pulse inputs, applied as the reference speed-commands. Also, simple 2-degree of freedom test-bed is developed in our laboratory to help test the open-loop and closed-loop experimental investigations. The non-linear motor-control map is found to perform better in BLDC motor speed tracking control performance and thereby helping achieve better quad-copter roll-angle attitude control.

  1. Aggregation in quads but not pairs of rats exposed to cat odor or bright light.

    Science.gov (United States)

    Bowen, Michael T; Keats, Kirily; Kendig, Michael D; Cakic, Vince; Callaghan, Paul D; McGregor, Iain S

    2012-07-01

    In many prey species aggregation of individuals is a defensive strategy commonly employed in response to predators and predator-related cues. However, very little work has explored this adaptive response in laboratory rats. It is known that individual rats show characteristic defensive responses to predator odors, such as hiding, avoidance, inhibition of foraging, feeding and reproduction, and risk assessment directed toward the odor source. However, whether these species-typical responses in individuals are altered in the presence of other conspecifics is yet to be characterized. The present study therefore examined the defensive response of groups of two rats (dyads) or four rats (quads) to two unconditioned stressors: bright ambient light and cat odor (a 2g ball of cat fur). The dyads and quads were formed from familiar cage mates and test sessions (20 min) occurred in a large open arena (1200 mm(2)) to which the rats had been extensively habituated under dark conditions. The results showed that when quads of rats were exposed to either cat odor or bright light in this arena, they showed characteristic increases in close social proximity, termed "huddling". A tight grouping of 3 (triplet) or 4 (quad) rats was commonly seen in response to cat fur, while triplets were more commonly seen in response to bright light. Interestingly there was no evidence for increased social proximity in dyads exposed to either stressor, only in quads. However, cat odor caused other signs of fear (such as decreased locomotor activity and increased defecation) in both quads and dyads. It is concluded that huddling is a rodent defensive strategy in rats when anxiogenic stimuli are encountered by larger groups of rats. Copyright © 2012 Elsevier B.V. All rights reserved.

  2. Quad-copter UAV BLDC Motor Control: Linear v/s non-linear control maps

    OpenAIRE

    Deep Parikh; Jignesh Patel; Jayesh Barve

    2015-01-01

    This paper presents some investigations and comparison of using linear versus non-linear static motor-control maps for the speed control of a BLDC (Brush Less Direct Current) motors used in quad-copter UAV (Unmanned Aerial Vehicles). The motor-control map considered here is the inverse of the static map relating motor-speed output to motor-voltage input for a typical out-runner type Brushless DC Motors (BLDCM).  Traditionally, quad-copter BLDC motor speed control uses simple linear motor-cont...

  3. 100 Gbps IM/DD links using quad-polarization: Performance, complexity, and power dissipation

    DEFF Research Database (Denmark)

    Saldaña Cercos, Silvia; Piels, Molly; Estaran Tolosa, Jose Manuel

    2015-01-01

    A computational complexity, power consumption, and receiver sensitivity analysis for three different scenarios for short-range direct detection links is presented: 1) quad-polarization, 2) wavelength division multiplexing (WDM), and 3) parallel optics. Results show that the power consumption...... penalty associated to the quad-polarization digital signal processing (DSP) is negligibly small. However, the required analog to digital converters account for 47.6% of the total system power consumption. Transmission of 4x32 Gbps over 2 km standard single mode fiber is achieved with a receiver...

  4. Multifunctional reactors

    NARCIS (Netherlands)

    Westerterp, K.R.

    1992-01-01

    Multifunctional reactors are single pieces of equipment in which, besides the reaction, other functions are carried out simultaneously. The other functions can be a heat, mass or momentum transfer operation and even another reaction. Multifunctional reactors are not new, but they have received much

  5. 76 FR 19746 - Expansion of Foreign-Trade Zone 133; Quad-Cities, IL/IA

    Science.gov (United States)

    2011-04-08

    ... given in the Federal Register (75 FR 12729, 3/17/2010) and the application has been processed pursuant... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE Foreign-Trade Zones Board Expansion of Foreign-Trade Zone 133; Quad-Cities, IL/IA Pursuant to...

  6. Reversibility of the Quad-Edge operations in the Voronoi data structure

    DEFF Research Database (Denmark)

    Mioc, Darka; Anton, François; Gold, Christopher

    2007-01-01

    In Geographic Information Systems the reversibility of map update operations have not been explored yet. In this paper we are using the Voronoi based Quad-edge data structure to define reversible map update operations. The reversibility of the map operations have been formalised at the lowest level...

  7. Parameter Estimation from Improved Measurements of the CMB from QUaD

    CERN Document Server

    Ade, P; Bowden, M; Brown, M L; Cahill, G; Castro, P G; Church, S; Culverhouse, T; Friedman, R B; Ganga, K; Gear, W K; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; O'Sullivan, C; Piccirillo, L; Pryke, C; Rajguru, N; Rusholme, B; Schwarz, R; Taylor, A N; Thompson, K L; Turner, A H; Wu, E Y S; Zemcov, M

    2009-01-01

    We evaluate the ability of cosmic microwave background (CMB) polarization spectra to constrain cosmological models by analyzing a multi-experiment CMB dataset including the final analysis of the QUaD experiment. We provide the best limits on parameters from combined polarization data and find that QUaD spectra combined with additional CMB datasets using the optimal pivot scale of k_p=0.013 Mpc-1 prefer standard LCDM parameters of {omch2, ombh2, H_0, A_s, n_s, tau}={0.113, 0.0224, 70.6, 2.29 times 10^-9, 0.960, 0.086}, with the confidence regions of ombh2, omch2 and H_0 tightened due to the presence of QUaD data. QUaD alone constrains cold dark matter and baryon densities and the acoustic scale very well. The temperature and polarization sub-sets each provide good limits on cosmological parameters which are consistent with values obtained from a combination of existing CMB data. We incorporate small-scale CMB data to provide the tightest constraint on tensor modes from CMB data alone.

  8. Improved measurements of the temperature and polarization of the CMB from QUaD

    CERN Document Server

    Ade, P; Bowden, M; Cahill, G; Castro, P G; Church, S; Culverhouse, T; Friedman, R B; Ganga, K; Gear, W K; Gupta, S; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; O'Sullivan, C; Piccirillo, L; Pryke, C; Rajguru, N; Rusholme, B; Schwarz, R; Taylor, A N; Thompson, K L; Turner, A H; Wu, E Y S; Zemcov, M

    2009-01-01

    We present an improved analysis of the final dataset from the QUaD experiment. Using an improved technique to remove ground contamination, we double the effective sky area and hence increase the precision of our CMB power spectrum measurements by ~30% versus that previously reported. In addition, we have improved our modeling of the instrument beams and have reduced our absolute calibration uncertainty from 5% to 3.5% in temperature. The robustness of our results is confirmed through extensive jackknife tests and by way of the agreement we find between our two fully independent analysis pipelines. For the standard 6-parameter LCDM model, the addition of QUaD data marginally improves the constraints on a number of cosmological parameters over those obtained from the WMAP experiment alone. The impact of QUaD data is significantly greater for a model extended to include either a running in the scalar spectral index, or a possible tensor component, or both. Adding both the QUaD data and the results from the ACBAR...

  9. QUAD: a computer package for the analysis of QUantal Assay Data.

    Science.gov (United States)

    Morgan, B J; Pack, S E; Smith, D M

    1989-12-01

    The computer package QUAD has been developed at the University of Kent, U.K. It is menu driven and written in Advanced BASIC. It runs on IBM PC compatible machines equipped with a suitable graphics facility such as CGA or simulated CGA. QUAD is available on a floppy disk, for a small handling charge. QUAD has four main functions: it performs a logit analysis of quantal assay data; it provides a flexible way of analysing the data, allowing dose transformations and providing alternative confidence intervals for EDp values; it produces a range of diagnostics for assessing the fit of models to data; it provides and fits two families of extended models, each containing the logit as a special case. The package makes use of the latest statistical research, and fitted models are displayed by means of the good graphics facilities available on microcomputers. This document describes the facilities available in detail, and provides and discusses, illustrations of the package at work. QUAD has been designed as a pilot package. Further additions and developments are planned and described later.

  10. A Novel Multilevel Quad-Inverter Configuration for Quasi Six-Phase Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick

    2016-01-01

    This paper developed a novel quad-inverter configuration for multilevel six-phase asymmetrical open-winding AC converter. Proposal found to be suited for (low-voltage/high-current) applications such as AC tractions and `More-Electric Aircraft' propulsion systems. Modular power circuit comprises o...

  11. A novel double quad-inverter configuration for multilevel twelve-phase open-winding converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick William

    2016-01-01

    This paper describes a novel proposal of double quad-inverter configuration for multilevel twelve-phase open-winding ac converter. Modular power units are developed from reconfigured eight classical three-phase voltage source inverters (VSIs). Each VSI has one additional bi-directional switching ...

  12. 100 Gbps IM/DD links using quad-polarization: Performance, complexity, and power dissipation

    DEFF Research Database (Denmark)

    Saldaña Cercos, Silvia; Piels, Molly; Estaran Tolosa, Jose Manuel;

    2015-01-01

    A computational complexity, power consumption, and receiver sensitivity analysis for three different scenarios for short-range direct detection links is presented: 1) quad-polarization, 2) wavelength division multiplexing (WDM), and 3) parallel optics. Results show that the power consumption pena...

  13. Reactor vessel

    OpenAIRE

    Makkee, M.; Kapteijn, F.; Moulijn, J.A

    1999-01-01

    A reactor vessel (1) comprises a reactor body (2) through which channels (3) are provided whose surface comprises longitudinal inwardly directed parts (4) and is provided with a catalyst (6), as well as buffer bodies (8, 12) connected to the channels (3) on both sides of the reactor body (2) and comprising connections for supplying (9, 10, 11) and discharging (13, 14, 15) via the channels (3) gases and/or liquids entering into a reaction with each other and substances formed upon this reactio...

  14. Chemical Reactors.

    Science.gov (United States)

    Kenney, C. N.

    1980-01-01

    Describes a course, including content, reading list, and presentation on chemical reactors at Cambridge University, England. A brief comparison of chemical engineering education between the United States and England is also given. (JN)

  15. Reactor Neutrinos

    Directory of Open Access Journals (Sweden)

    Soo-Bong Kim

    2013-01-01

    Full Text Available We review the status and the results of reactor neutrino experiments. Short-baseline experiments have provided the measurement of the reactor neutrino spectrum, and their interest has been recently revived by the discovery of the reactor antineutrino anomaly, a discrepancy between the reactor neutrino flux state of the art prediction and the measurements at baselines shorter than one kilometer. Middle and long-baseline oscillation experiments at Daya Bay, Double Chooz, and RENO provided very recently the most precise determination of the neutrino mixing angle θ13. This paper provides an overview of the upcoming experiments and of the projects under development, including the determination of the neutrino mass hierarchy and the possible use of neutrinos for society, for nonproliferation of nuclear materials, and geophysics.

  16. NUCLEAR REACTOR

    Science.gov (United States)

    Miller, H.I.; Smith, R.C.

    1958-01-21

    This patent relates to nuclear reactors of the type which use a liquid fuel, such as a solution of uranyl sulfate in ordinary water which acts as the moderator. The reactor is comprised of a spherical vessel having a diameter of about 12 inches substantially surrounded by a reflector of beryllium oxide. Conventionnl control rods and safety rods are operated in slots in the reflector outside the vessel to control the operation of the reactor. An additional means for increasing the safety factor of the reactor by raising the ratio of delayed neutrons to prompt neutrons, is provided and consists of a soluble sulfate salt of beryllium dissolved in the liquid fuel in the proper proportion to obtain the result desired.

  17. Reactor Engineering

    Science.gov (United States)

    Lema, Juan M.; López, Carmen; Eibes, Gemma; Taboada-Puig, Roberto; Moreira, M. Teresa; Feijoo, Gumersindo

    In this chapter, the engineering aspects of processes catalyzed by peroxidases will be presented. In particular, a discussion of the existing technologies that utilize peroxidases for different purposes, such as the removal of recalcitrant compounds or the synthesis of polymers, is analyzed. In the first section, the essential variables controlling the process will be investigated, not only those that are common in any enzymatic system but also those specific to peroxidative reactions. Next, different reactor configurations and operational modes will be proposed, emphasizing their suitability and unsuitability for different systems. Finally, two specific reactors will be described in detail: enzymatic membrane reactors and biphasic reactors. These configurations are especially valuable for the treatment of xenobiotics with high and poor water solubility, respectively.

  18. Reactor Neutrinos

    OpenAIRE

    Lasserre, T.; Sobel, H.W.

    2005-01-01

    We review the status and the results of reactor neutrino experiments, that toe the cutting edge of neutrino research. Short baseline experiments have provided the measurement of the reactor neutrino spectrum, and are still searching for important phenomena such as the neutrino magnetic moment. They could open the door to the measurement of coherent neutrino scattering in a near future. Middle and long baseline oscillation experiments at Chooz and KamLAND have played a relevant role in neutrin...

  19. 1:24,000 Grid of Louisiana, Geographic NAD83, LGS (2007) [quad6k_losco_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — This "QUAD24K_LOSCO_2007" ploygon shapefile is a reference index to the polygon footprints of 1:24,000 scale quadrangles for Louisiana and a selected surrounding...

  20. 1:12,000 Grid of Louisiana, Geographic NAD83, LGS (2007) [quad12k_losco_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — This "QUAD12K_LOSCO_2007" ploygon shapefile is a reference index to the polygon footprints of Digital Orthographic Quarter Quadrangles (DOQQs) for Louisiana and a...

  1. 1:6,000 Grid of Louisiana, Geographic NAD83, LGS (2007) [quad6k_losco_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — This "QUAD6K_LOSCO_2007" ploygon shapefile is a reference index to the polygon footprints of quarters of the Digital Orthographic Quarter Quadrangles (DOQQs), or...

  2. STABILIZED CONTROLLER DESIGN FOR ATTITUDE AND ALTITUDE CONTROLLING OF QUAD-ROTOR UNDER DISTURBANCE AND NOISY CONDITIONS

    Directory of Open Access Journals (Sweden)

    M. Hassan Tanveer

    2013-01-01

    Full Text Available This article presents a control approach to obtain the better stabilization in attitude and altitude of quad-rotor under different disturbance conditions. In the standard Quad-rotor rotor type UAV, controlling of attitude and altitude is one of the most critical tasks and appropriate controller for stabilization of UAV is essential and necessary. These two controls under various conditions of disturbances was a field of research stimulating for the researchers. The controller proposed is contingent on the PID feedback structure with Extended Kalman Filter (EKF. From Lyapunov Stability Theorem, it is proved that quad-rotor proposed altitude control system is asymptotic as well exponentially stability. Extended Kalman Filter (EKF is used to filter out the sensors and system noises. Finally, the simulations carried out on MATLAB and the result proved the effectiveness of proposed recommended method for stabilization of attitude and altitude of quad-rotor.

  3. Index Grids, quad index, Published in 2009, 1:24000 (1in=2000ft) scale, Washington County.

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — This Index Grids dataset, published at 1:24000 (1in=2000ft) scale, was produced all or in part from Other information as of 2009. It is described as 'quad index'....

  4. Energy harvesting in a quad-stable harvester subjected to random excitation

    Directory of Open Access Journals (Sweden)

    Zhi-yong Zhou

    2016-02-01

    Full Text Available In response to the defects of bi-stable energy harvester (BEH, we develop a novel quad-stable energy harvester (QEH to improve harvesting efficiency. The device is made up of a bimorph cantilever beam having a tip magnet and three external fixed magnets. By adjusting the positions of the fixed magnets and the distances between the tip magnet and the fixed ones, the quad-stable equilibrium positions can emerge. The potential energy shows that the barriers of the QEH are lower than those of the BEH for the same separation distance. Experiment results reveal that the QEH can realize snap-through easier and make a dense snap-through in response under random excitation. Moreover, its strain and voltage both become large for snap-through between the nonadjacent stable positions. There exists an optimal separation distance for different excitation intensities.

  5. Design of a Quad-Band Wide-Angle Microwave Metamaterial Absorber

    Science.gov (United States)

    Ren, Yu-Hui; Ding, Jun; Guo, Chen-Jiang; Qu, Yan; Song, Yi-Chuan

    2017-01-01

    We report the design, analysis, fabrication, and measurement of a quad-band microwave metamaterial absorber that exhibits four distinct high absorption peaks at specific resonance frequencies. The proposed structure consists of a metallic hexagonal patch layer on top of a dielectric substrate with a metallic film as bottom layer. The simulation and experimental results show that the absorber presents four distinctive perfect (>90%) absorption peaks up to incidence angle of 40° for both transverse electric and transverse magnetic modes. The results prove that this kind of quad-band absorber has good performance over a wide incidence angle range and is polarization insensitive. Moreover, the experimental and numerical simulation results are essentially in agreement.

  6. A quad-pol radar scattering model for use in remote sensing of lava flow morphology

    Science.gov (United States)

    Campbell, Bruce A.; Zisk, Stanley H.; Mouginis-Mark, Peter J.

    1989-01-01

    Mapping of spatial variations in surface roughness over large regions is required to understand the nature of volcanic terrains. An invertible scattering model for quad-polarization radar data is presented to assist in the remote-sensing analysis of lava flow surface morphology. This model permits separation of the polarized part of the radar echo into quasispecular, dihedral, and small-perturbation scatterin components, based on an assumed surface dielectric constant. Tests are presented for a quad-pol scene of Craters of the Moon National Monument in Idaho, where there are a number of basaltic lava flows of differing surface morphology. Comparison of calculated model components with the observed morphology of the lava flows suggests that this technique may be useful for the remote description of changes in surface roughness. The scattering mechanisms chosen to represent the polarizing behavior of the real surface display correlations which indicate that they are sensitive to the expected scales of roughness.

  7. Development of Adaptive Tilt Tracker that Utilizes QUAD-cell Detector to Track Extended Objects

    Science.gov (United States)

    2014-03-17

    21] K. Ogata , Discrete-Time Control Systems 2nd ed. Upper Saddle River, NJ: Prentice Hall, 1995 [22] R. McGuigan, “Effect of Coudé...Tracker/QUAD-cell Control Problem ..................................132 5.1.5 Recommending Adaptive Tracker Capabilities...detector’s frame rate and the control loop gain to reduce tracker error in real-time [2]. In 2010, the SOR upgraded its tilt tracker system along with the

  8. Stabilization and control of quad-rotor helicopter using a smartphone device

    Science.gov (United States)

    Desai, Alok; Lee, Dah-Jye; Moore, Jason; Chang, Yung-Ping

    2013-01-01

    In recent years, autonomous, micro-unmanned aerial vehicles (micro-UAVs), or more specifically hovering micro- UAVs, have proven suitable for many promising applications such as unknown environment exploration and search and rescue operations. The early versions of UAVs had no on-board control capabilities, and were difficult for manual control from a ground station. Many UAVs now are equipped with on-board control systems that reduce the amount of control required from the ground-station operator. However, the limitations on payload, power consumption and control without human interference remain the biggest challenges. This paper proposes to use a smartphone as the sole computational device to stabilize and control a quad-rotor. The goal is to use the readily available sensors in a smartphone such as the GPS, the accelerometer, the rate-gyros, and the camera to support vision-related tasks such as flight stabilization, estimation of the height above ground, target tracking, obstacle detection, and surveillance. We use a quad-rotor platform that has been built in the Robotic Vision Lab at Brigham Young University for our development and experiments. An Android smartphone is connected through the USB port to an external hardware that has a microprocessor and circuitries to generate pulse-width modulation signals to control the brushless servomotors on the quad-rotor. The high-resolution camera on the smartphone is used to detect and track features to maintain a desired altitude level. The vision algorithms implemented include template matching, Harris feature detector, RANSAC similarity-constrained homography, and color segmentation. Other sensors are used to control yaw, pitch, and roll of the quad-rotor. This smartphone-based system is able to stabilize and control micro-UAVs and is ideal for micro-UAVs that have size, weight, and power limitations.

  9. Expanding Comparative Literature into Comparative Sciences Clusters with Neutrosophy and Quad-stage Method

    Directory of Open Access Journals (Sweden)

    Fu Yuhua

    2016-08-01

    Full Text Available By using Neutrosophy and Quad-stage Method, the expansions of comparative literature include: comparative social sciences clusters, comparative natural sciences clusters, comparative interdisciplinary sciences clusters, and so on. Among them, comparative social sciences clusters include: comparative literature, comparative history, comparative philosophy, and so on; comparative natural sciences clusters include: comparative mathematics, comparative physics, comparative chemistry, comparative medicine, comparative biology, and so on.

  10. Cosmological parameter estimation with QUaD CMB polarization and temperature experiment

    OpenAIRE

    Memari, Yasin

    2009-01-01

    In this thesis we examine the theoretical origin and statistical features of the Cosmic Microwave Background radiation. We particularly focus on the CMB power spectra and cosmological parameter estimation from QUaD CMB experiment data in order to derive implications for the concordance cosmological model. In chapter 4 we present a detailed parameter estimation analysis of the combined polarization and temperature power spectra from the second and third season observations of...

  11. Improved Measurements of the Temperature and Polarization of the Cosmic Microwave Background from QUaD

    OpenAIRE

    Brown, M L; Ade, P.; Bock, J.; Bowden, M.; Cahill, G.; Castro, P.G. (Patricia Garrido); Church, S.; Culverhouse, T.; Friedman, R. B.; Ganga, K.; Gear, W.K.; S. Gupta; Hinderks, J.; Kovac, John M.; Lange, A. E.

    2009-01-01

    We present an improved analysis of the final data set from the QUaD experiment. Using an improved technique to remove ground contamination, we double the effective sky area and hence increase the precision of our cosmic microwave background (CMB) power spectrum measurements by ~30% versus that previously reported. In addition, we have improved our modeling of the instrument beams and have reduced our absolute calibration uncertainty from 5% to 3.5% in temperature. The robustness of our result...

  12. Toward a High-Efficient Utilization of Solar Radiation by Quad-Band Solar Spectral Splitting.

    Science.gov (United States)

    Cao, Feng; Huang, Yi; Tang, Lu; Sun, Tianyi; Boriskina, Svetlana V; Chen, Gang; Ren, Zhifeng

    2016-12-01

    The promising quad-band solar spectral splitter incorporates the properties of the optical filter and the spectrally selective solar thermal absorber can direct PV band to PV modules and absorb thermal band energy for thermal process with low thermal losses. It provides a new strategy for spectral splitting and offers potential ways for hybrid PVT system design. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Bioconversion reactor

    Science.gov (United States)

    McCarty, Perry L.; Bachmann, Andre

    1992-01-01

    A bioconversion reactor for the anaerobic fermentation of organic material. The bioconversion reactor comprises a shell enclosing a predetermined volume, an inlet port through which a liquid stream containing organic materials enters the shell, and an outlet port through which the stream exits the shell. A series of vertical and spaced-apart baffles are positioned within the shell to force the stream to flow under and over them as it passes from the inlet to the outlet port. The baffles present a barrier to the microorganisms within the shell causing them to rise and fall within the reactor but to move horizontally at a very slow rate. Treatment detention times of one day or less are possible.

  14. NUMERICAL SIMULATION FOR SHALLOW FLOW AND POLLUTANT DISPERSION BASED ON QUAD-TREE MESHES

    Institute of Scientific and Technical Information of China (English)

    LIU Xiao-dong; HUA Zu-lin

    2006-01-01

    A 2D depth-averaged flow-pollutant coupled model based on quad-tree meshes was established to accurately simulate flows in water areas with irregular natural boundaries in this paper. The grids were generated by recursive subdivision about seeding points. A new neighbor-finding algorithm was presented. The governing equations were discretized in collocated conservative variables by using the finite volume method, and the normal flux of mass, momentum and pollutants across the interface between cells were computed by a Godunov-type Flux Difference Splitting (FDS) scheme. The model was applied to simulate flow fields around a groin. The computed values are in agreement with observed data. The results indicate that quad-tree meshes have fine local resolution, high efficiency and easy local refinement. It is clear that the quad-tree grid model can offer gains in efficiency when applied to complex flow domains or strong shear flows. Finally, the model is applied to flow fields and concentration fields simulation in Jiangsu Haizhou Bay. The simulated polluted area is matched well with observations. Therefore, this model can be used to predict flow and concentration fields of actual water area with irregular natural land boundaries.

  15. WETLAND MAPPING WITH SAR/QUAD-POL DATA ACQUIRED DURING TANDEM-X SCIENCE PHASE

    Directory of Open Access Journals (Sweden)

    M. Mleczko

    2016-06-01

    Full Text Available The aim of this study was to exploit fully polarimetric SAR data acquired during TanDEM-X – Science Phase (2014/2015 over herbaceous wetlands of the Biebrza National Park (BbNP in North-Eastern Poland for mapping seasonally flooded grasslands and permanent natural vegetation associations. The main goal of this work was to estimate the advantage of fully polarimetric radar images (QuadPol versus alternative polarization (AltPol modes. The methodology consisted in processing of several data subsets through polarimetric decompositions of complex quad-pol datasets, classification of multitemporal backscattering images, complementing backscattering images with Shannon Entropy, exploitation of interferometric coherence from tandem operations. In each case the multidimensional stack of images has been classified using ISODATA unsupervised clustering algorithm. With 6 QUAD-POL TSX/TDX acquisitions it was possible to distinguish correctly 5 thematic classes related to their water regime: permanent water bodies, temporarily flooded areas, wet grasslands, dry grasslands and common reed. This last category was possible to distinguish from deciduous forest only with Yamaguchi 4 component decomposition. The interferometric coherence calculated for tandem pairs turned out not so efficient as expected for this wetland mapping.

  16. The QUaD Galactic Plane Survey 1: Maps And Analysis of Diffuse Emission

    CERN Document Server

    Culverhouse, T; Bock, J; Bowden, M; Brown, M L; Cahill, G; Castro, P G; Church, S; Friedman, R; Ganga, K; Gear, W K; Gupta, S; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; Schwarz, R; Sullivan, C O'; Piccirillo, L; Pryke, C; Rajguru, N; Rusholme, B; Taylor, A N; Thompson, K L; Turner, A H; Wu, E Y S; Zemcov, M

    2010-01-01

    We present a survey of ~800 square degrees of the galactic plane observed with the QUaD telescope. The primary product of the survey are maps of Stokes I, Q and U parameters at 100 and 150 GHz, with spatial resolution 5 and 3.5 arcminutes respectively. Two regions are covered, spanning approximately 245-295 and 315-5 degrees in galactic longitude l, and -4QUaD band, while better agreement is found at 150 GHz. A smaller excess is observed when comparing QUaD 100 GHz data to WMAP 5-year W band; in this case the excess is likely due to the w...

  17. MCP detector read out with a bare quad Timepix at kilohertz frame rates

    Science.gov (United States)

    Vallerga, J.; Raffanti, R.; Tremsin, A.; McPhate, J.; Siegmund, O.

    2011-01-01

    The existing Berkeley neutron sensitive MCP/Timepix hybrid detector has been very successful at demonstrating energy resolved spatial imaging with a single Timepix ASIC read out at a ~ 30 Hz frame rate where each neutron's position and time (energy) is determined (X,Y,E). By increasing the detector format using a quad arrangement of Timepix readouts and increasing the frame rate to 1 kHz, we can increase our total event throughput by a factor of 120, thereby taking full advantage of the high fluxes of modern pulsed neutron sources (106 n cm-2 s-1). The key to this conversion is a new design for the ASIC readout, called the Berkeley Quad Timepix detector, consisting of 3 major subsystems. The first is a quad (2 × 2) bare Timepix ASIC board mounted directly behind the neutron sensitive MCPs in a hermetic vacuum enclosure with a sapphire window. The data from the Timepix ASICs flow to the second subsystem called the Interface board whose field programmable gate array (FPGA) rearranges and converts the digital bit stream to LVDS logic levels before sending downstream to the third subsystem, the Roach board. The Roach board is also FPGA based, and takes the data from all the ASICs and analyses the frames to extract information on the input events to pass on to the host PC. This paper describes in detail the hardware and firmware designs to accomplish this task.

  18. Sonochemical Reactors.

    Science.gov (United States)

    Gogate, Parag R; Patil, Pankaj N

    2016-10-01

    Sonochemical reactors are based on the generation of cavitational events using ultrasound and offer immense potential for the intensification of physical and chemical processing applications. The present work presents a critical analysis of the underlying mechanisms for intensification, available reactor configurations and overview of the different applications exploited successfully, though mostly at laboratory scales. Guidelines have also been presented for optimum selection of the important operating parameters (frequency and intensity of irradiation, temperature and liquid physicochemical properties) as well as the geometric parameters (type of reactor configuration and the number/position of the transducers) so as to maximize the process intensification benefits. The key areas for future work so as to transform the successful technique at laboratory/pilot scale into commercial technology have also been discussed. Overall, it has been established that there is immense potential for sonochemical reactors for process intensification leading to greener processing and economic benefits. Combined efforts from a wide range of disciplines such as material science, physics, chemistry and chemical engineers are required to harness the benefits at commercial scale operation.

  19. Development of an Effective System Identification and Control Capability for Quad-copter UAVs

    Science.gov (United States)

    Wei, Wei

    In recent years, with the promise of extensive commercial applications, the popularity of Unmanned Aerial Vehicles (UAVs) has dramatically increased as witnessed by publications and mushrooming research and educational programs. Over the years, multi-copter aircraft have been chosen as a viable configuration for small-scale VTOL UAVs in the form of quad-copters, hexa-copters and octo-copters. Compared to the single main rotor configuration such as the conventional helicopter, multi-copter airframes require a simpler feedback control system and fewer mechanical parts. These characteristics make these UAV platforms, such as quad-copter which is the main emphasis in this dissertation, a rugged and competitive candidate for many applications in both military and civil areas. Because of its configuration and relative size, the small-scale quad-copter UAV system is inherently very unstable. In order to develop an effective control system through simulation techniques, obtaining an accurate dynamic model of a given quad-copter is imperative. Moreover, given the anticipated stringent safety requirements, fault tolerance will be a crucial component of UAV certification. Accurate dynamic modeling and control of this class of UAV is an enabling technology and is imperative for future commercial applications. In this work, the dynamic model of a quad-copter system in hover flight was identified using frequency-domain system identification techniques. A new and unique experimental system, data acquisition and processing procedure was developed catering specifically to the class of electric powered multi-copter UAV systems. The Comprehensive Identification from FrEquency Responses (CIFER RTM) software package, developed by US Army Aviation Development Directorate -- AFDD, was utilized along with flight tests to develop dynamic models of the quad-copter system. A new set of flight tests were conducted and the predictive capability of the dynamic models were successfully validated

  20. The Vacuum-Compacted Regolith Gripping Mechanism and Unmanned Flights via Quad-Rotors

    Science.gov (United States)

    Scott, Rollin L.

    2014-01-01

    During the course of the Kennedy Space Center Summer Internship, two main experiments were performed: The Vacuum-Compacted Regolith Gripping Mechanism and Unmanned Flights via Quad-copters. The objectives of the Vacuum-Compacted Regolith Gripping Mechanism, often abbreviated as the Granular Gripper, are to exhibit Space Technology, such as a soft robotic hand, lift different apparatuses used to excavate regolith, and conserve energy while executing its intended task. The project is being conducted to test how much weight the Granular Gripper can hold. With the use of an Animatronic Robotic Hand, Arduino Uno, and other components, the system was calibrated before actually conducting the intended weight test. The maximum weight each finger could hold with the servos running, in the order of pinky, ring, middle, and index fingers, are as follows: 1.340N, 1.456 N, 0.9579 N, and 1.358 N. Using the small vacuum pump system, the maximum weight each finger could hold, in the same order, was: 4.076 N, 6.159 N, 5.454 N, and 4.052 N. The maximum torques on each of the fingers when the servos were running, in the same respective order, was: 0.0777 Nm, 0.0533 Nm, 0.0648 Nm, and 0.0532 Nm. The maximum torques on the individual fingers, when the small vacuum pump was in effect, in the same order as above, was: 0.2318 Nm, 0.3032 Nm, 0.2741 Nm, and 0.1618 Nm. In testing all the fingers with the servos running, the total weight was 5.112 N and the maximum torque on the all the fingers was 0.2515 Nm. However, when the small vacuum pump system was used, the total weight was 19.741 N and the maximum torque on the all the fingers was 0.9713 Nm. The conclusion that was drawn stated that using the small vacuum pump system proved nearly 4 times more effective when testing how much weigh the hand could hold. The resistance provided by the compacted sand in the glove allowed more weight to be held by the hand and glove. Also, when the servos turned off and the hand still retaining its

  1. O aparelho quadrihélice (Quad-helix e suas variações The Quad-helix appliance and their variations

    Directory of Open Access Journals (Sweden)

    Mario Sergio Duarte

    2006-04-01

    Full Text Available O presente artigo objetivou mostrar a eficiência dos vários desenhos do aparelho quadrihélice, de Ricketts, na correção das desarmonias dentoalveolares. Devido às suas várias formas de confecção, assim como de sua ativação, o quadrihélice tornou-se um acessório útil não somente na sobrecorreção da discrepância transversal e sagital, mas também no tratamento das más oclusões da Classe II, divisão 1, de Angle, principalmente nos casos em que a rotação do molar é desejada como parte do tratamento. Também é relevante o seu efeito no tratamento das mordidas abertas anteriores, atuando como coadjuvante no tratamento dos fatores ambientais que contribuem, muitas vezes, para exacerbar o desenvolvimento das más oclusões. Em relação ao alinhamento do arco dentário, o quadrihélice abrevia essa fase do tratamento em 4 a 5 meses (o tratamento convencional levaria muito mais tempo e pelo menos uma grande série de troca de arcos em mecânicas de nivelamento. Portanto, este trabalho tem a intenção de mostrar algumas das ativações possíveis do aparelho quadrihélice, bem como algumas de suas variações, que contribuem para conseguir resultados estáveis em longo prazo.The aim of this present article was to show the efficiency of several drawings of Ricketts Quad-helix appliance in the correction of dentoalveolar disharmonies. Due its varied forms, as well as its activation, the Quad-helix became a useful accessory not only in overcorrecting the transversal discrepancy and sagittal, but also in treating Angle Class II Division 1 malocclusions, mainly when molar rotation is a necessary part of the treatment. It is also relevant its effect in the treatment of anterior open-bites. It gives support in the treatment of environmental factors that contribute to exacerbate the development of malocclusions. In relation to dental arch alignment, the Quad-helix appliance abbreviate this treatment phase in 4 to 5 months, what would

  2. Quad Tree-based Level-of-details Representation of Digital Globe

    Directory of Open Access Journals (Sweden)

    Sudhir Porwal

    2013-01-01

    Full Text Available Three-dimensional visualization of the geographic data using a digital globe model has been an integral part of a modern GIS system. The visualization of the digital globe model presents many challenges not found in traditional terrain visualization system. The representation of the digital earth (globe model is important to efficiently render the geographical data without any distortion either at equator or Polar Regions. This paper presents a uniform scheme for efficient quad tree based level-of-details (LOD representation of the digital globe to minimize the distortion at Polar Regions and meets the requirement of fast frame rate rendering.

  3. The QUaD Galactic Plane Survey. I. Maps and Analysis of Diffuse Emission

    OpenAIRE

    Culverhouse, Thomas; Ade, Peter; Bock, James; Bowden, Melanie; Brown, Michael L.; Cahill, Gary; Castro, Patricia G.; Church, Sarah E.; Friedman, Robert; Ganga, Ken; Gear, Walter K.; Gupta, Sujata; Hinderks, James R.; Kovac, John M.; Lange, Andrew E.

    2010-01-01

    We present a survey of ~800 deg\\(^{2}\\) of the galactic plane observed with the QUaD telescope. The primary products of the survey are maps of Stokes I, Q, and U parameters at 100 and 150 GHz, with spatial resolution of 5' and 3'.5, respectively. Two regions are covered, spanning approximately 245°-295° and 315°-5° in the galactic longitude l and –4° < b < +4° in the galactic latitude b. At 0°.02 square pixel size, the median sensitivity is 74 and 107 kJy sr\\(^{–1}\\) at 100 GHz and 150 GHz re...

  4. Fault Estimation for a Quad-Rotor MAV Using a Polynomial Observer

    OpenAIRE

    Aguilar-Sierra, Hipolito; Flores Colunga, Gerardo Ramon; Salazar, Sergio; Lozano, Rogelio

    2013-01-01

    International audience; This work addresses the problem of fault detection and diagnosis (FDD) for a quad-rotor mini air vehicle (MAV). Actuator faults are considered on this paper. The basic idea behind the proposed method is to estimate the faults signals using the extended state observers theory. To estimate the faults, a polynomial observer (Aguilar et al. 2011; Mata-Machuca et al., Commun Nonlinear Sci Numer Simul 15(12):4114-4130, 2010, BioSystems 100(1):65-69, 2010) is presented by usi...

  5. Quad Tech印刷套准系统亮相CHINA PRINT 2009

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    @@ 在刚刚结束的2009 CHINAPRINT展会上,QuadTech公司带来了其卓越的印刷套准系统:适用于报纸印刷的配有AccuCam的闭环彩色控制系统,适用于包装印刷配有ClearLogic的AutoTron 2600全自动套准系统和Heliostat 300静电油墨辅助系统,以及配有InstrumentFlight和SpectralCam的商业轮转用的闭环彩色控制系统.

  6. Process characteristics and design methods for a 300 deg quad OP amp

    Science.gov (United States)

    Beasom, J. D.; Patterson, R. B., III

    1981-01-01

    The results of process characterization, circuit design, and reliability studies for the development of a quad OP amplifier intended for use up to 300 C are presented. A dielectrically isolated complementary vertical bipolar process was chosen to fabricate the amplifier in order to eliminate isolation leakage and the possibility of latch up. Characterization of NPN and PNP junctions showed them to be suitable for use up to 300 C. Interconnect reliability was predicted to be greater than four years mean time between failure. Parasitic MOS formation was eliminated by isolation of each device.

  7. On the Lagrangian structure of 3D consistent systems of asymmetric quad-equations

    CERN Document Server

    Boll, Raphael

    2011-01-01

    Recently, the first-named author gave a classification of 3D consistent 6-tuples of quad-equations with the tetrahedron property; several novel asymmetric 6-tuples have been found. Due to 3D consistency, these 6-tuples can be extended to discrete integrable systems on Z^m. We establish Lagrangian structures and flip-invariance of the action functional for the class of discrete integrable systems involving equations for which some of the biquadratics are non-degenerate and some are degenerate. This class covers, among others, some of the above mentioned novel systems.

  8. Modified quad helix appliance for thumb sucking and cross bite correction

    Directory of Open Access Journals (Sweden)

    C Vinay

    2013-01-01

    Full Text Available Digit sucking habit is a learned pattern of behavior commonly seen in children of preschool age. Prolonged digit sucking beyond the preschool age, lead to the development of malocclusion such as anterior open bite, maxillary constriction and posterior crossbite. Treatment strategies include interception of habit and correction of the malocclusion. The present case report describes a modified quad helix appliance used successfully in a 9-year-old child to intercept thumb sucking habit and simultaneous correction of posterior crossbite. The appliance has the advantage of easy fabrication, being versatile and more patients compliant.

  9. Parity violation constraints using cosmic microwave background polarization spectra from 2006 and 2007 observations by the QUaD polarimeter.

    Science.gov (United States)

    Wu, E Y S; Ade, P; Bock, J; Bowden, M; Brown, M L; Cahill, G; Castro, P G; Church, S; Culverhouse, T; Friedman, R B; Ganga, K; Gear, W K; Gupta, S; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; Piccirillo, L; Pryke, C; Rajguru, N; Rusholme, B; Schwarz, R; O'Sullivan, C; Taylor, A N; Thompson, K L; Turner, A H; Zemcov, M

    2009-04-24

    We constrain parity-violating interactions to the surface of last scattering using spectra from the QUaD experiment's second and third seasons of observations by searching for a possible systematic rotation of the polarization directions of cosmic microwave background photons. We measure the rotation angle due to such a possible "cosmological birefringence" to be 0.55 degrees +/-0.82 degrees (random) +/-0.5 degrees (systematic) using QUaD's 100 and 150 GHz temperature-curl and gradient-curl spectra over the spectra over the multipole range 200Lorentz-violating interactions to violation on cosmological scales.

  10. Hybrid adsorptive membrane reactor

    Science.gov (United States)

    Tsotsis, Theodore T. (Inventor); Sahimi, Muhammad (Inventor); Fayyaz-Najafi, Babak (Inventor); Harale, Aadesh (Inventor); Park, Byoung-Gi (Inventor); Liu, Paul K. T. (Inventor)

    2011-01-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  11. D and DR Reactors

    Data.gov (United States)

    Federal Laboratory Consortium — The world's second full-scale nuclear reactor was the D Reactor at Hanford which was built in the early 1940's and went operational in December of 1944.D Reactor ran...

  12. Hybrid adsorptive membrane reactor

    Science.gov (United States)

    Tsotsis, Theodore T.; Sahimi, Muhammad; Fayyaz-Najafi, Babak; Harale, Aadesh; Park, Byoung-Gi; Liu, Paul K. T.

    2011-03-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  13. Implementation of a single quad MS detector in routine QC analysis of peptide drugs

    Directory of Open Access Journals (Sweden)

    Matthias D’Hondt

    2016-02-01

    Full Text Available A newly developed single quad mass spectrometry (MS detector was coupled to a ultra-high performance liquid chromatography (UPLC system and implemented in the routine quality control (QC and impurity analysis of four therapeutic peptides, namely bleomycin sulfate, tyrothricin, vancomycin HCl and bacitracin, which were selected given their multi-component drug nature and their closely structurally related impurity profiles. The QC and impurity profiling results obtained using the ultra-high performance liquid chromatography ultraviolet/mass spectrometry (UPLC-UV/MS detection system were analyzed against the results obtained using traditional high performance liquid chromatography-ultraviolet detection (HPLC-UV methods derived from pharmacopoeial methods. In general, the used stationary phases of sub-2 µm particle (UPLC technology resulted in lower limits of detection and higher resolution separations, which resulted in more detected impurities and shorter overall run times contrasting the traditional HPLC columns. Moreover, online coupling with a single quad MS detector allowed direct peak identification of the main compounds as well as small impurities, hereby increasing the information content without the need of reference standards.

  14. Mechanical evaluation of quad-helix appliance made of low-nickel stainless steel wire

    Directory of Open Access Journals (Sweden)

    Rogério Lacerda dos Santos

    2013-06-01

    Full Text Available OBJECTIVE: The objective of this study was to test the hypothesis that there is no difference between stainless steel and low-nickel stainless steel wires as regards mechanical behavior. Force, resilience, and elastic modulus produced by Quad-helix appliances made of 0.032-inch and 0.036-inch wires were evaluated. METHODS: Sixty Quad-helix appliances were made, thirty for each type of alloy, being fifteen for each wire thickness, 0.032-in and 0.036-in. All the archwires were submitted to mechanical compression test using an EMIC DL-10000 machine simulating activations of 4, 6, 9, and 12 mm. Analysis of variance (ANOVA with multiple comparisons and Tukey's test were used (p < 0.05 to assess force, resilience, and elastic modulus. RESULTS: Statistically significant difference in the forces generated, resilience and elastic modulus were found between the 0.032-in 0.036-in thicknesses (p < 0.05. CONCLUSIONS: Appliances made of low-nickel stainless steel alloy had force, resilience, and elastic modulus similar to those made of stainless steel alloy.

  15. Quad-Band Bowtie Antenna Design for Wireless Communication System Using an Accurate Equivalent Circuit Model

    Directory of Open Access Journals (Sweden)

    Mohammed Moulay

    2015-01-01

    Full Text Available A novel configuration of quad-band bowtie antenna suitable for wireless application is proposed based on accurate equivalent circuit model. The simple configuration and low profile nature of the proposed antenna lead to easy multifrequency operation. The proposed antenna is designed to satisfy specific bandwidth specifications for current communication systems including the Bluetooth (frequency range 2.4–2.485 GHz and bands of the Unlicensed National Information Infrastructure (U-NII low band (frequency range 5.15–5.35 GHz and U-NII mid band (frequency range 5.47–5.725 GHz and used for mobile WiMAX (frequency range 3.3–3.6 GHz. To validate the proposed equivalent circuit model, the simulation results are compared with those obtained by the moments method of Momentum software, the finite integration technique of CST Microwave studio, and the finite element method of HFSS software. An excellent agreement is achieved for all the designed antennas. The analysis of the simulated results confirms the successful design of quad-band bowtie antenna.

  16. Quadruplex-single nucleotide polymorphisms (Quad-SNP) influence gene expression difference among individuals.

    Science.gov (United States)

    Baral, Aradhita; Kumar, Pankaj; Halder, Rashi; Mani, Prithvi; Yadav, Vinod Kumar; Singh, Ankita; Das, Swapan K; Chowdhury, Shantanu

    2012-05-01

    Non-canonical guanine quadruplex structures are not only predominant but also conserved among bacterial and mammalian promoters. Moreover recent findings directly implicate quadruplex structures in transcription. These argue for an intrinsic role of the structural motif and thereby posit that single nucleotide polymorphisms (SNP) that compromise the quadruplex architecture could influence function. To test this, we analysed SNPs within quadruplex motifs (Quad-SNP) and gene expression in 270 individuals across four populations (HapMap) representing more than 14,500 genotypes. Findings reveal significant association between quadruplex-SNPs and expression of the corresponding gene in individuals (P analysis of Quad-SNPs obtained from population-scale sequencing of 1000 human genomes showed relative selection bias against alteration of the structural motif. To directly test the quadruplex-SNP-transcription connection, we constructed a reporter system using the RPS3 promoter-remarkable difference in promoter activity in the 'quadruplex-destabilized' versus 'quadruplex-intact' promoter was noticed. As a further test, we incorporated a quadruplex motif or its disrupted counterpart within a synthetic promoter reporter construct. The quadruplex motif, and not the disrupted-motif, enhanced transcription in human cell lines of different origin. Together, these findings build direct support for quadruplex-mediated transcription and suggest quadruplex-SNPs may play significant role in mechanistically understanding variations in gene expression among individuals.

  17. Nuclear reactor neutron shielding

    Energy Technology Data Exchange (ETDEWEB)

    Speaker, Daniel P; Neeley, Gary W; Inman, James B

    2017-09-12

    A nuclear reactor includes a reactor pressure vessel and a nuclear reactor core comprising fissile material disposed in a lower portion of the reactor pressure vessel. The lower portion of the reactor pressure vessel is disposed in a reactor cavity. An annular neutron stop is located at an elevation above the uppermost elevation of the nuclear reactor core. The annular neutron stop comprises neutron absorbing material filling an annular gap between the reactor pressure vessel and the wall of the reactor cavity. The annular neutron stop may comprise an outer neutron stop ring attached to the wall of the reactor cavity, and an inner neutron stop ring attached to the reactor pressure vessel. An excore instrument guide tube penetrates through the annular neutron stop, and a neutron plug comprising neutron absorbing material is disposed in the tube at the penetration through the neutron stop.

  18. Assembly of an Experimental Quad-Rotor Type UAV for Testing a Novel Autonomous Flight Control Strategy

    Directory of Open Access Journals (Sweden)

    Shahida Khatoon

    2013-12-01

    Full Text Available In this research a prototype experimental Quad-rotor type UAV have been assembled using low cost components easily available in the Indian market. The quad-copter is used for testing a novel autonomous flight control strategy developed using embedded system. In order to enable a mini-UAV to perform target acquisition, localization and continuous surveillance in real world environment one must develop a technology which may be a combination of aircraft engineering, control systems, and wireless communication. The major limiting factors in developing the capabilities of small low cost UAVs are connectivity, computational processing power and lack of resource integration. To overcome these limitations in this research we have tried to assemble an experimental quad-rotor prototype UAV capable of being remotely controlled in the range of 20 meter, which is specifically designed as an economical, moderately functional, small airborne platform intended to meet the requirement for fast-response to time-critical events in many small private sectors or government agencies. The experimental prototype quad-copter has been successfully implemented and tested for 15 minutes smooth flight time.

  19. A radarsat-2 quad-polarized time series for monitoring crop and soil conditions in Barrax, Spain

    Science.gov (United States)

    The European Space Agency (ESA) along with multiple university and agency investigators joined to conduct the AgriSAR Campaign in 2009. The main objective was to analyze a dense time series of RADARSAT-2 quad-pol data to define and quantify the performance of Sentinel-1 and other future ESA C-Band ...

  20. Usefulness of a Rugby-shaped hohlraum in a Laser M'egaJoule (LMJ) 40-quad configuration

    Science.gov (United States)

    Malinie, G.; Vandenboomgaerde, M.; Bastian, J.; Galmiche, D.; Laffite, S.; Liberatore, S.

    2007-11-01

    The LMJ setup will consist of 60 quads in a 3-cone configuration, at angles 33.2^o, 49^o and 59.5^o. First ignition attempts in indirect drive are planned to be made on the way to the completion of the full facility, with only 40 quads in a 2-cone configuration, at angles 33.2^o and 49^o. By analytic considerations, we show that in a 40-quad configuration, the angular location of the hohlraum outer irradiating ring, as seen from the capsule, must be closer to the laser entrance hole than with the full LMJ. The use of a Rugby-shaped hohlraum instead of a cylinder therefore allows to keep a correct symmetry while reducing the wall surface, which improves the global energetic efficiency of the target. Simplified 2D numerical simulations of Rugby hohlraums are presented, achieving a yield of about 30 MJ with our 1.215 mm-radius, CH-uniform-ablator capsule. These results suggests this kind of hohlraum might be an interesting candidate for 40-quad ignition experiments. Work on optimizing the present design and refining the numerical simulations is currently pursued.

  1. A 'quad-phantom' film dosimeter for use as a multi-planar verification tool for PRESAGE/optical-CT.

    Science.gov (United States)

    Stunja, L; Thomas, A; Adamovics, J; Deasy, J; Oldham, M

    2010-01-01

    INTRODUCTION: To develop and characterize the accuracy and reproducibility of a quad-phantom dosimeter which will serve as an independent verification tool during commissioning of a PRESAGE/optical-CT 3D dosimetry system. METHODS: A 16cm × 12cm cylindrical quad-phantom was constructed from four pieces of solid polyurethane mimicking the PRESAGE material. Films were placed and anchored in orthogonal planes and the quad-phantom was fastened tightly together and placed in a water-filled Styrofoam container for irradiation. A simple, two-field plan consisting of 6×6cm anterior-posterior and right-lateral 6MV photon beams (400cGy) was delivered three times (fresh films inserted for each) with a Varian Clinac 600C. Image registration was performed in the Computational Environment for Radiological Research (CERR) and dose profiles and gamma analysis was performed in CERR and MATLAB. RESULTS #ENTITYSTARTX00026; DISCUSSION: Excellent reproducibility was observed during the irradiations, with ~2.3% standard deviation between all pixels. Using a 3%, 3mm gamma criteria, excellent dosimetric accuracy was observed, with 98.8% and 96.3% passing rates in the sagittal and axial planes, respectively. CONCLUSION: The preliminary results indicate that the quad-phantom can serve as a reproducible and accurate system for high resolution dosimetry in orthogonal planes and should serve as an effective verification tool for PRESAGE/optical-CT in more challenging clinical scenarios.

  2. A Micro-Force Sensor with Slotted-Quad-Beam Structure for Measuring the Friction in MEMS Bearings

    Directory of Open Access Journals (Sweden)

    Yan Liu

    2013-09-01

    Full Text Available Presented here is a slotted-quad-beam structure sensor for the measurement of friction in micro bearings. Stress concentration slots are incorporated into a conventional quad-beam structure to improve the sensitivity of force measurements. The performance comparison between the quad-beam structure sensor and the slotted-quad-beam structure sensor are performed by theoretical modeling and finite element (FE analysis. A hollow stainless steel probe is attached to the mesa of the sensor chip by a tailor-made organic glass fixture. Concerning the overload protection of the fragile beams, a glass wafer is bonded onto the bottom of sensor chip to limit the displacement of the mesa. The calibration of the packaged device is experimentally performed by a tri-dimensional positioning stage, a precision piezoelectric ceramic and an electronic analytical balance, which indicates its favorable sensitivity and overload protection. To verify the potential of the proposed sensor being applied in micro friction measurement, a measurement platform is established. The output of the sensor reflects the friction of bearing resulting from dry friction and solid lubrication. The results accord with the theoretical modeling and demonstrate that the sensor has the potential application in measuring the micro friction force under stable stage in MEMS machines.

  3. A micro-force sensor with slotted-quad-beam structure for measuring the friction in MEMS bearings.

    Science.gov (United States)

    Liu, Huan; Yang, Shuming; Zhao, Yulong; Jiang, Zhuangde; Liu, Yan; Tian, Bian

    2013-09-30

    Presented here is a slotted-quad-beam structure sensor for the measurement of friction in micro bearings. Stress concentration slots are incorporated into a conventional quad-beam structure to improve the sensitivity of force measurements. The performance comparison between the quad-beam structure sensor and the slotted-quad-beam structure sensor are performed by theoretical modeling and finite element (FE) analysis. A hollow stainless steel probe is attached to the mesa of the sensor chip by a tailor-made organic glass fixture. Concerning the overload protection of the fragile beams, a glass wafer is bonded onto the bottom of sensor chip to limit the displacement of the mesa. The calibration of the packaged device is experimentally performed by a tri-dimensional positioning stage, a precision piezoelectric ceramic and an electronic analytical balance, which indicates its favorable sensitivity and overload protection. To verify the potential of the proposed sensor being applied in micro friction measurement, a measurement platform is established. The output of the sensor reflects the friction of bearing resulting from dry friction and solid lubrication. The results accord with the theoretical modeling and demonstrate that the sensor has the potential application in measuring the micro friction force under stable stage in MEMS machines.

  4. A novel five-level optimized carrier multilevel PWM quad-inverter six-phase AC drive

    DEFF Research Database (Denmark)

    Sanjeevikumar, P.; Blaabjerg, F.; Wheeler, Pat

    2016-01-01

    A novel single carrier pulse-width modulation (PWM) for a new quad-inverter configuration for multilevel six-phase asymmetrical open-winding ac converter is proposed in this article. Modularity of the circuit consist of four standard two-level voltage source inverters (VSIs) with slight modificat...

  5. A 'quad-phantom' film dosimeter for use as a multi-planar verification tool for PRESAGE/optical-CT

    Science.gov (United States)

    Stunja, L.; Thomas, A.; Adamovics, J.; Deasy, J.; Oldham, M.

    2010-11-01

    Introduction: To develop and characterize the accuracy and reproducibility of a 'quad-phantom' dosimeter which will serve as an independent verification tool during commissioning of a PRESAGE/optical-CT 3D dosimetry system. Methods: A 16cm × 12cm cylindrical quad-phantom was constructed from four pieces of solid polyurethane mimicking the PRESAGE material. Films were placed and anchored in orthogonal planes and the quad-phantom was fastened tightly together and placed in a water-filled Styrofoam container for irradiation. A simple, two-field plan consisting of 6×6cm anterior-posterior and right-lateral 6MV photon beams (400cGy) was delivered three times (fresh films inserted for each) with a Varian Clinac 600C. Image registration was performed in the Computational Environment for Radiological Research (CERR) and dose profiles and gamma analysis was performed in CERR and MATLAB. Results & Discussion: Excellent reproducibility was observed during the irradiations, with ~2.3% standard deviation between all pixels. Using a 3%, 3mm gamma criteria, excellent dosimetric accuracy was observed, with 98.8% and 96.3% passing rates in the sagittal and axial planes, respectively. Conclusion: The preliminary results indicate that the quad-phantom can serve as a reproducible and accurate system for high resolution dosimetry in orthogonal planes and should serve as an effective verification tool for PRESAGE/optical-CT in more challenging clinical scenarios.

  6. Reactor and method of operation

    Science.gov (United States)

    Wheeler, John A.

    1976-08-10

    A nuclear reactor having a flattened reactor activity curve across the reactor includes fuel extending over a lesser portion of the fuel channels in the central portion of the reactor than in the remainder of the reactor.

  7. Using implicit association tests in age-heterogeneous samples: The importance of cognitive abilities and quad model processes.

    Science.gov (United States)

    Wrzus, Cornelia; Egloff, Boris; Riediger, Michaela

    2017-08-01

    Implicit association tests (IATs) are increasingly used to indirectly assess people's traits, attitudes, or other characteristics. In addition to measuring traits or attitudes, IAT scores also reflect differences in cognitive abilities because scores are based on reaction times (RTs) and errors. As cognitive abilities change with age, questions arise concerning the usage and interpretation of IATs for people of different age. To address these questions, the current study examined how cognitive abilities and cognitive processes (i.e., quad model parameters) contribute to IAT results in a large age-heterogeneous sample. Participants (N = 549; 51% female) in an age-stratified sample (range = 12-88 years) completed different IATs and 2 tasks to assess cognitive processing speed and verbal ability. From the IAT data, D2-scores were computed based on RTs, and quad process parameters (activation of associations, overcoming bias, detection, guessing) were estimated from individual error rates. Substantial IAT scores and quad processes except guessing varied with age. Quad processes AC and D predicted D2-scores of the content-specific IAT. Importantly, the effects of cognitive abilities and quad processes on IAT scores were not significantly moderated by participants' age. These findings suggest that IATs seem suitable for age-heterogeneous studies from adolescence to old age when IATs are constructed and analyzed appropriately, for example with D-scores and process parameters. We offer further insight into how D-scoring controls for method effects in IATs and what IAT scores capture in addition to implicit representations of characteristics. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  8. LHC Quad

    CERN Multimedia

    CERN audiovisual service

    1993-01-01

    A QUADrupole is a magnetic lense. Its purpose is to focus the beam in one of the principal planes. Contrary to an optical lense (which focusses normally in both planes), a quadrupole focusses in one plane but defocusses in the other. Explications et gros plans

  9. Comparison of Quad-Polarimetric and Dual-Polarimetric SAR Data Capabilities for River Ice Classification

    Science.gov (United States)

    Los, H.; Pawlowski, B.; Osinska-Skotak, K.; Pluto-Kossakowska, J.

    2016-08-01

    River ice is one of the largest challenges of flood prevention during the winter. In the last decade, significant progress has been made on river ice research based on Earth observation data, especially with Synthetic Aperture Radar (SAR) systems. In this study, we compare the capabilities of quad-polarimetric and dual-polarimetric RADARSAT-2 data for river ice classification on the Lower Vistula. Dual-polarized datasets are generated by reducing polarization channels in original fully-polarized data. To classify images, we use supervised classification based on a maximum- likelihood algorithm. The results show that even with a reduced number of polarization channels, the classification result still presented satisfactory overall accuracy of above 85%.

  10. Hexa Helix: Modified Quad Helix Appliance to Correct Anterior and Posterior Crossbites in Mixed Dentition

    Directory of Open Access Journals (Sweden)

    Syed Mohammed Yaseen

    2012-01-01

    Full Text Available Among the commonly encountered dental irregularities which constitute developing malocclusion is the crossbite. During primary and mixed dentition phase, the crossbite is seen very often and if left untreated during these phases then a simple problem may be transformed into a more complex problem. Different techniques have been used to correct anterior and posterior crossbites in mixed dentition. This case report describes the use of hexa helix, a modified version of quad helix for the management of anterior crossbite and bilateral posterior crossbite in early mixed dentition. Correction was achieved within 15 weeks with no damage to the tooth or the marginal periodontal tissue. The procedure is a simple and effective method for treating anterior and bilateral posterior crossbites simultaneously.

  11. Attitude Control of Quad Rotors QTW-UAV with Tilt Wing Mechanism

    Science.gov (United States)

    Suzuki, Satoshi; Zhijia, Ren; Horita, Yoshikazu; Nonami, Kenzo; Kimura, Gaku; Bando, Toshio; Hirabayashi, Daisuke; Furuya, Mituhiro; Yasuda, Kenta

    In this paper, we propose an autonomous attitude control of a quad tilt wing-unmanned aerial vehicle (QTW-UAV). A QTW-UAV can achieve vertical takeoff and landing; further, hovering flight, which are characteristic of rotary-wing aircraft such as helicopter. And high cruising speeds, which is a characteristic of fixed-wing aircraft, can be also achieved by changing the angle of the rotors and wings by a tilt mechanism. First, we construct an attitude model of the QTW-UAV by using the identification method. We then design the attitude control system with a Kalman filter-based linear quadratic integral (LQI) control method; the experiment results show that a model-based control design is very useful for the autonomous control of a QTW-UAV.

  12. Development and Validation of a Triple Quad LC/MS Method for Fiber Dye Analysis

    Science.gov (United States)

    Connolly-Ingram, Ceirin M.

    This study aims to determine whether the analysis of dyed fiber through liquid chromatography (HPLC) with triple-quadrupole mass spectrometry (MS) can be used as a reliable alternative to the current chemical techniques used to differentiate dyes. Other methods of analysis involving HPLC and MS have proven to be capable of distinguishing chemically different dyes within a few dye classifications, but none have proven capable of providing a complete alternative to the current accepted technique of thin layer chromatography (TLC). In theory, HPLC-triple quad MS is capable of providing more reproducible and reliable data than the conventional TLC methods with a much greater depth of measurable information with which to characterize dye components. In this study, dyes will be extracted from various types of fibers, including commonly worn types like cotton, polyester, nylon, and wool, and examine dyes from most of the eight different dye classes.

  13. CMOS buried quad p-n junction photodetector for multi-wavelength analysis.

    Science.gov (United States)

    Richard, Charles; Courcier, Thierry; Pittet, Patrick; Martel, Stéphane; Ouellet, Luc; Lu, Guo-Neng; Aimez, Vincent; Charette, Paul G

    2012-01-30

    This paper presents a buried quad p-n junction (BQJ) photodetector fabricated with a HV (high-voltage) CMOS process. Multiple buried junction photodetectors are wavelength-sensitive devices developed for spectral analysis applications where a compact integrated solution is preferred over systems involving bulk optics or a spectrometer due to physical size limitations. The BQJ device presented here is designed for chip-based biochemical analyses using simultaneous fluorescence labeling of multiple analytes such as with advanced labs-on-chip or miniaturized photonics-based biosensors. Modeling and experimental measurements of the spectral response of the device are presented. A matrix-based method for estimating individual spectral components in a compound spectrum is described. The device and analysis method are validated via a test setup using individually modulated LEDs to simulate light from 4-component fluorescence emission.

  14. Moving object detection using a background modeling based on entropy theory and quad-tree decomposition

    Science.gov (United States)

    Elharrouss, Omar; Moujahid, Driss; Elkah, Samah; Tairi, Hamid

    2016-11-01

    A particular algorithm for moving object detection using a background subtraction approach is proposed. We generate the background model by combining quad-tree decomposition with entropy theory. In general, many background subtraction approaches are sensitive to sudden illumination change in the scene and cannot update the background image in scenes. The proposed background modeling approach analyzes the illumination change problem. After performing the background subtraction based on the proposed background model, the moving targets can be accurately detected at each frame of the image sequence. In order to produce high accuracy for the motion detection, the binary motion mask can be computed by the proposed threshold function. The experimental analysis based on statistical measurements proves the efficiency of our proposed method in terms of quality and quantity. And it even outperforms substantially existing methods by perceptional evaluation.

  15. Its okay to be a quad: wheelchair rugby players sense of community.

    Science.gov (United States)

    Goodwin, Donna; Johnston, Keith; Gustafson, Paul; Elliott, Melanie; Thurmeier, Robin; Kuttai, Heather

    2009-04-01

    This study explored the social experience of wheelchair rugby from the perspective of the players. Eleven national level rugby players (10 males, 1 female with a mean age of 33 years) shared their experiences through the phenomenological methods of semistructured focus group interviews and artifacts. Three themes emerged from the thematic analysis (a) it's okay to be a quad, (b) don't tell us we can't, and (c) the power of wheelchair rugby. The athletes identified with a shared sense of community and the membership, fulfillment of need, influence, and shared emotional connections they used to authentically express themselves through their sport. The implications of the findings were interpreted within the theoretical context of psychological sense of community.

  16. Neutron Particle Effects on a Quad-Redundant Flight Control Computer

    Science.gov (United States)

    Eure, Kenneth; Belcastro, Celeste M.; Gray, W Steven; Gonzalex, Oscar

    2003-01-01

    This paper describes a single-event upset experiment performed at the Los Alamos National Laboratory. A closed-loop control system consisting of a Quad-Redundant Flight Control Computer (FCC) and a B737 simulator was operated while the FCC was exposed to a neutron beam. The purpose of this test was to analyze the effects of neutron bombardment on avionics control systems operating at altitudes where neutron strikes are probable. The neutron energy spectrum produced at the Los Alamos National Laboratory is similar in shape to the spectrum of atmospheric neutrons but much more intense. The higher intensity results in accelerated life tests that are representative of the actual neutron radiation that a FCC may receive over a period of years.

  17. First Experiment of IECAS P-Band Quad-Pol SAR System in Circular Imaging Mode

    Science.gov (United States)

    Hong, Wen; Li, Yang; Yin, Qiang; Lin, Yun; Chen, Erxue; Pottier, Eric

    2013-01-01

    Within the framework of the DRAGON2 project, the Institute of Electronics, Chinese Academy of Sciences (IECAS) continuously had a tight collaboration with the European and the Chinese partners. Our contribution to the joint research, separated by 4 working packages: land cover analysis, earth surface deformation monitoring and DEM extraction, forest vertical structure parameters extraction, and PolSARpro software continued development, is reviewed in the beginning. Furthermore, a joint study between IECAS - NKLMIT and University of Rennes-1 -Institute of Electronics and Telecommunications, about DEM based soil moisture inversion using POLSAR data is reviewed. Besides, a compact-pol calibration algorithm for a wide-band ground-based SAR system and a supervised land cover classification method are proposed here. Finally, the first experiment of IECAS P-band quad-pol SAR system in circular imaging mode is introduced.

  18. A Novel Multilevel Quad-Inverter Configuration for Quasi Six-Phase Open-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick

    2016-01-01

    -level modulation (MSCFM) algorithm is developed in this work and easy for implementing in real digital processors. The proposed modulation algorithm is capable of generating, 5-level voltages at each output of four VSI as one equivalent to multilevel inverter. The total power is among the four DC sources......This paper developed a novel quad-inverter configuration for multilevel six-phase asymmetrical open-winding AC converter. Proposal found to be suited for (low-voltage/high-current) applications such as AC tractions and `More-Electric Aircraft' propulsion systems. Modular power circuit comprises...... of standard four three-phase voltage source inverter (VSI) and each connected to the open-end windings. Each VSIs are incorporated with one bi-directional switching device (MOSFET/IGBT) per phase and two capacitors with neutral point connected. Further, an original modified single carrier five...

  19. Hybridized plasmon resonant modes in molecular metallodielectric quad-triangles nanoantenna

    Science.gov (United States)

    Ahmadivand, Arash; Sinha, Raju; Pala, Nezih

    2015-11-01

    In this study, we examined the plasmon response for both metallic and metallodielectric nanoantennas composed of four gold (Au) triangles in a quadrumer orientation. Tailoring an artificial metallic quad-triangles nanoantenna, it is shown that the structure is able to support pronounced plasmon and Fano resonances in the visible spectrum. Using plasmon transmutation effect, we showed that the plasmonic response of the proposed cluster can be enhanced with the placement of carbon nanoparticles in the offset gaps between the proximal triangles. It is verified that this structural modification gives rise to formation of new collective magnetic antibonding (dark) plasmon modes. Excitation of these subradiant dark modes leads to formation of narrower and deeper Fano resonances in the spectral response of the metallodielectric nanoantenna. To investigate the practical applications of the metallodielectric structure, we immersed the nano-assembly in various liquids with different refractive indices to define its sensitivity to the environmental perturbation as a plasmonic biological sensor.

  20. Quad-plane stereoscopic PIV for fine-scale structure measurements in turbulence

    Science.gov (United States)

    Naka, Y.; Tomita, K.; Shimura, M.; Fukushima, N.; Tanahashi, M.; Miyauchi, T.

    2016-05-01

    The fine-scale structure in turbulence is investigated by quad-plane stereoscopic particle image velocimetry (QPSPIV). The quad-plane consists of two each of different polarizations and wavelengths, and it provides three velocity components at four independent parallel planes. Measurements have been undertaken in the developed region of a turbulent round jet with a spatial resolution sufficient to capture the small-scale structures. The advantage of the QPSPIV is presented in terms of the spectral response in the evaluation of the out-of-plane velocity gradient. The full velocity gradient tensor is computed with a fourth-order finite difference scheme in the out-of-plane direction as well as the in-plane directions. The turbulence quantities, such as the vorticity components, the energy dissipation rate and the second and third invariants of the velocity gradient tensor, are computed according to their faithful definitions. The coherent fine-scale eddies are extracted from the present QPSPIV data. The probability density functions of the diameter and the maximum azimuthal velocity of the extracted eddies exhibit their peak at approximately 8η and 1.5u_k, respectively, where η and u_k are the Kolmogorov length and velocity. These values agree well with the data in the literature. The phase-averaged distributions of turbulence quantities around the coherent fine-scale eddy indicate an apparent elliptic feature around the axis. Furthermore, the state of the strain rate exerting the eddy is quantified from the phase-averaged distributions of eigenvalues of the strain rate tensor and the alignment of the corresponding eigenvectors against the axis. The present study gives a solid experimental support of the coherent fine-scale structures in turbulence, and the technique can be applied to various flow fields and to the higher Reynolds number condition.

  1. Modeling Surface Roughness to Estimate Surface Moisture Using Radarsat-2 Quad Polarimetric SAR Data

    Science.gov (United States)

    Nurtyawan, R.; Saepuloh, A.; Budiharto, A.; Wikantika, K.

    2016-08-01

    Microwave backscattering from the earth's surface depends on several parameters such as surface roughness and dielectric constant of surface materials. The two parameters related to water content and porosity are crucial for estimating soil moisture. The soil moisture is an important parameter for ecological study and also a factor to maintain energy balance of land surface and atmosphere. Direct roughness measurements to a large area require extra time and cost. Heterogeneity roughness scale for some applications such as hydrology, climate, and ecology is a problem which could lead to inaccuracies of modeling. In this study, we modeled surface roughness using Radasat-2 quad Polarimetric Synthetic Aperture Radar (PolSAR) data. The statistical approaches to field roughness measurements were used to generate an appropriate roughness model. This modeling uses a physical SAR approach to predicts radar backscattering coefficient in the parameter of radar configuration (wavelength, polarization, and incidence angle) and soil parameters (surface roughness and dielectric constant). Surface roughness value is calculated using a modified Campbell and Shepard model in 1996. The modification was applied by incorporating the backscattering coefficient (σ°) of quad polarization HH, HV and VV. To obtain empirical surface roughness model from SAR backscattering intensity, we used forty-five sample points from field roughness measurements. We selected paddy field in Indramayu district, West Java, Indonesia as the study area. This area was selected due to intensive decreasing of rice productivity in the Northern Coast region of West Java. Third degree polynomial is the most suitable data fitting with coefficient of determination R2 and RMSE are about 0.82 and 1.18 cm, respectively. Therefore, this model is used as basis to generate the map of surface roughness.

  2. QUAD versus cfDNA in an urban population in the second trimester for detection of trisomy 21: a cost sensitivity analysis.

    Science.gov (United States)

    Crimmins, Sarah; Doyle, Lauren; Slejko, Julia; Kopelman, Jerome N; Turan, Ozhan

    2017-10-01

    To compare the unit cost of noninvasive prenatal testing (cell-free DNA [cfDNA]) in an urban population who did not have first-trimester screening as a primary screening tool for trisomy 21 (T21) to multiple marker screening (QUAD). Retrospective study of all QUAD screens performed at a single center from 2013 to 2015. All QUAD screen performed between 15 and 21 weeks were included in the study. Exclusion criteria were patients without anatomy scans or delivery information. Utilizing our population characteristics, we extrapolated to determine the cost of QUAD with additional screening (cfDNA and amniocentesis) versus QUAD for this entire population. 590 QUAD screens were performed during the study time period. After ultrasound correction of gestational age, 5.9% (35) were screen positive. Within this cohort, 51.4% (18) patients underwent cfDNA and 11.4% (4) had invasive testing. No cases of T21 were identified. It would be cost equivalent to offer cfDNA as a primary screen for T21 at less than $360.54 to the entire population regardless of a priori risk status. Invasive procedures were reduced by 55.4%. cfDNA is an acceptable option for second-trimester screening and as a primary screen eliminates the need for multi-step screening preserving valuable healthcare resources.

  3. Limited Human Factors Assessment of the QuadGard Limb Protection System: U.S. Marine Corps Systems Command Limb Protection Program Overview (QuadGard Phases 4 and 5 Production Designs)

    Science.gov (United States)

    2011-09-01

    pants or trouser form with light duty suspenders, waist belt, and articulated sleeve segments, which were anchored to the current OTV. The QuadGard...Arms raised vertically, then palms touch. 5. Arms extended horizontally, hips fixed, flex thorax forward. 6. Arms extended horizontally, hips fixed...flex thorax to the rear. 7. Arms extended horizontally, hips fixed, rotate thorax . 8. Feet apart, bend right knee and touch floor/ground. 9. Feet

  4. Reactor Physics Programme

    Energy Technology Data Exchange (ETDEWEB)

    De Raedt, C

    2000-07-01

    The Reactor Physics and Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis on reactor fuel. This expertise is applied within the Reactor Physics and MYRRHA Research Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments. Progress and achievements in 1999 in the following areas are reported on: (1) investigations on the use of military plutonium in commercial power reactors; (2) neutron and gamma calculations performed for BR-2 and for other reactors; (3) the updating of neutron and gamma cross-section libraries; (4) the implementation of reactor codes; (6) the management of the UNIX workstations; and (6) fuel cycle studies.

  5. Generation and transmission of 512-Gb/s quad-carrier digital super-Nyquist spectral shaped signal.

    Science.gov (United States)

    Zhang, Junwen; Yu, Jianjun; Chi, Nan

    2013-12-16

    A novel digital super-Nyquist signal generation scheme is proposed to further suppress the Nyquist signal bandwidth and reduce the channel crosstalk without using optical pre-filtering. The spectrum of the generated super-Nyquist 9-QAM signal is much more compact compared with regular Nyquist QPSK signal. Therefore, only optical couplers are needed for super-Nyquist WDM channel multiplexing. By using the 64-GSa/s high speed DAC, 32-GBaud super-Nyquist 9-QAM signal is generated within 25-GHz grid for quad-carrier 400G channels. We successfully generate and transmit 4 channels quad-carrier 512-Gb/s super-Nyquist 9-QAM-like signal within 100-GHz grid over 2975-km at a net SE of 4b/s/Hz (after excluding the 20% soft-decision FEC overhead).

  6. Attrition reactor system

    Science.gov (United States)

    Scott, Charles D.; Davison, Brian H.

    1993-01-01

    A reactor vessel for reacting a solid particulate with a liquid reactant has a centrifugal pump in circulatory flow communication with the reactor vessel for providing particulate attrition, resulting in additional fresh surface where the reaction can occur.

  7. Fault Estimation and Control for a Quad-Rotor MAV Using a Polynomial Observer. Part I: Fault Detection

    OpenAIRE

    Flores Colunga, Gerardo Ramon; Aguilar-Sierra, Hipolito; Lozano, Rogelio; Salazar, Sergio

    2014-01-01

    International audience; This work addresses the problem of fault detection and diagnosis (FDD) for a quad-rotor mini aerial vehicle (MAV). Actuator faults are considered on this paper. The basic idea behind the proposed method is to estimate the faults signals using the extended state observers theory. To estimate the faults, a polynomial observer is presented by using the available measurements and know inputs of the system. In order to investigate the observability and diagnosability proper...

  8. A case report of bilateral Brodie bite in early mixed dentition using bonded constriction quad-helix appliance.

    Science.gov (United States)

    Nojima, Kunihiko; Takaku, Sakiko; Murase, Chiaki; Nishii, Yasushi; Sueishi, Kenji

    2011-01-01

    Brodie bite is a comparatively rare type of malocclusion found in primary and mixed dentition. It not only adversely affects chewing and muscle functions, but also impairs normal growth and development of the mandible. This report describes the therapeutic results of a patient with bilateral Brodie bite in early mixed dentition after using a bonded constriction quad-helix appliance. The patient, a boy aged 9 years and 2 months, first visited our hospital after occlusal abnormality in the molar region was detected at a local dental clinic. Case analysis resulted in a diagnosis of bilateral Brodie bite with slight mandibular retrognathism. Treatment objectives were to reduce the arch width of the maxillary dentition and expand the mandibular arch in order to establish and stabilize molar occlusion and to achieve a Class I molar relation and appropriate overbite and overjet. Treatment comprised covering the occlusal surface of the maxillary molars with resin and attaching a bonded constriction quad-helix appliance joined with a 0.040-inch quad-helix wire. A bi-helix appliance was also fixed to the mandibular dentition. Brodie bite visibly improved after 5 months. Cervical headgear was then fitted and the patient observed until eruption of the permanent dentition was complete. Class I molar relation was achieved after 2 years and 6 months, although spacing remained in the maxillary and mandibular dentitions. Treatment of bilateral Brodie bite in mixed dentition by means of a bonded constriction quad-helix appliance attached to the maxillary dentition enabled effective bite opening and reduction in the width of maxillary arch independent of the patient's cooperation, providing good therapeutic outcome in a short time period.

  9. A Waterline Extraction Method from Remote Sensing Image Based on Quad-tree and Multiple Active Contour Model

    Directory of Open Access Journals (Sweden)

    YU Jintao

    2016-09-01

    Full Text Available After the characteristics of geodesic active contour model (GAC, Chan-Vese model(CV and local binary fitting model(LBF are analyzed, and the active contour model based on regions and edges is combined with image segmentation method based on quad-tree, a waterline extraction method based on quad-tree and multiple active contour model is proposed in this paper. Firstly, the method provides an initial contour according to quad-tree segmentation. Secondly, a new signed pressure force(SPF function based on global image statistics information of CV model and local image statistics information of LBF model has been defined, and then ,the edge stopping function(ESF is replaced by the proposed SPF function, which solves the problem such as evolution stopped in advance and excessive evolution. Finally, the selective binary and Gaussian filtering level set method is used to avoid reinitializing and regularization to improve the evolution efficiency. The experimental results show that this method can effectively extract the weak edges and serious concave edges, and owns some properties such as sub-pixel accuracy, high efficiency and reliability for waterline extraction.

  10. Least square based sliding mode control for a quad-rotor helicopter and energy saving by chattering reduction

    Science.gov (United States)

    Sumantri, Bambang; Uchiyama, Naoki; Sano, Shigenori

    2016-01-01

    In this paper, a new control structure for a quad-rotor helicopter that employs the least squares method is introduced. This proposed algorithm solves the overdetermined problem of the control input for the translational motion of a quad-rotor helicopter. The algorithm allows all six degrees of freedom to be considered to calculate the control input. The sliding mode controller is applied to achieve robust tracking and stabilization. A saturation function is designed around a boundary layer to reduce the chattering phenomenon that is a common problem in sliding mode control. In order to improve the tracking performance, an integral sliding surface is designed. An energy saving effect because of chattering reduction is also evaluated. First, the dynamics of the quad-rotor helicopter is derived by the Newton-Euler formulation for a rigid body. Second, a constant plus proportional reaching law is introduced to increase the reaching rate of the sliding mode controller. Global stability of the proposed control strategy is guaranteed based on the Lyapunov's stability theory. Finally, the robustness and effectiveness of the proposed control system are demonstrated experimentally under wind gusts, and are compared with a regular sliding mode controller, a proportional-differential controller, and a proportional-integral-differential controller.

  11. LMFBR type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, Hiroto

    1995-02-07

    A reactor container of the present invention has a structure that the reactor container is entirely at the same temperature as that at the inlet of the reactor and, a hot pool is incorporated therein, and the reactor container has is entirely at the same temperature and has substantially uniform temperature follow-up property transiently. Namely, if the temperature at the inlet of the reactor core changes, the temperature of the entire reactor container changes following this change, but no great temperature gradient is caused in the axial direction and no great heat stresses due to axial temperature distribution is caused. Occurrence of thermal stresses caused by the axial temperature distribution can be suppressed to improve the reliability of the reactor container. In addition, since the laying of the reactor inlet pipelines over the inside of the reactor is eliminated, the reactor container is made compact and the heat shielding structures above the reactor and a protection structure of container walls are simplified. Further, secondary coolants are filled to the outside of the reactor container to simplify the shieldings. The combined effects described above can improve economical property and reliability. (N.H.).

  12. Light water reactor safety

    CERN Document Server

    Pershagen, B

    2013-01-01

    This book describes the principles and practices of reactor safety as applied to the design, regulation and operation of light water reactors, combining a historical approach with an up-to-date account of the safety, technology and operating experience of both pressurized water reactors and boiling water reactors. The introductory chapters set out the basic facts upon which the safety of light water reactors depend. The central section is devoted to the methods and results of safety analysis. The accidents at Three Mile Island and Chernobyl are reviewed and their implications for light wate

  13. Nuclear reactor physics

    CERN Document Server

    Stacey, Weston M

    2010-01-01

    Nuclear reactor physics is the core discipline of nuclear engineering. Nuclear reactors now account for a significant portion of the electrical power generated worldwide, and new power reactors with improved fuel cycles are being developed. At the same time, the past few decades have seen an ever-increasing number of industrial, medical, military, and research applications for nuclear reactors. The second edition of this successful comprehensive textbook and reference on basic and advanced nuclear reactor physics has been completely updated, revised and enlarged to include the latest developme

  14. Spinning fluids reactor

    Science.gov (United States)

    Miller, Jan D; Hupka, Jan; Aranowski, Robert

    2012-11-20

    A spinning fluids reactor, includes a reactor body (24) having a circular cross-section and a fluid contactor screen (26) within the reactor body (24). The fluid contactor screen (26) having a plurality of apertures and a circular cross-section concentric with the reactor body (24) for a length thus forming an inner volume (28) bound by the fluid contactor screen (26) and an outer volume (30) bound by the reactor body (24) and the fluid contactor screen (26). A primary inlet (20) can be operatively connected to the reactor body (24) and can be configured to produce flow-through first spinning flow of a first fluid within the inner volume (28). A secondary inlet (22) can similarly be operatively connected to the reactor body (24) and can be configured to produce a second flow of a second fluid within the outer volume (30) which is optionally spinning.

  15. Performance analysis of different PSF shapes for the quad-HIDAC PET submillimetre resolution recovery

    Energy Technology Data Exchange (ETDEWEB)

    Ortega Maynez, Leticia, E-mail: lortega@uacj.mx [Departamento de Ingenieria Eectrica y Computacion , Universidad Autonoma de Ciudad Juarez, Avenida del Charro 450 Norte, C.P. 32310 Ciudad Juarez, Chihuahua (Mexico); Dominguez de Jesus Ochoa, Humberto; Villegas Osiris Vergara, Osslan; Gordillo, Nelly; Guadalupe Cruz Sanchez, Vianey; Gutierrez Casas, Efren David [Departamento de Ingenieria Eectrica y Computacion, Universidad Autonoma de Ciudad Juarez, Avenida del Charro 450 Norte, C.P. 32310 Ciudad Juarez, Chihuahua (Mexico)

    2011-10-01

    In pre-clinical applications, it is quite important to preserve the image resolution because it is necessary to show the details of structures of small animals. Therefore, small animal PET scanners require high spatial resolution and good sensitivity. For the quad-HIDAC PET scanner, which has virtually continuous spatial sampling; improvements in resolution, noise and contrast are obtained as a result of avoiding artifacts introduced by binning the data into sampled projections used during the reconstruction process. In order to reconstruct high-resolution images in 3D-PET, background correction and resolution recovery are included within the Maximum Likelihood list-mode Expectation Maximization reconstruction model. This paper, introduces the performance analysis of the Gaussian, Laplacian and Triangular kernels. The Full-Width Half-Maximum used for each kernel was varied from 0.8 to 1.6 mm. For each quality compartment within the phantom, transaxial middle slices from the 3D reconstructed images are shown. Results show that, according to the quantitative measures, the triangular kernel has the best performance.

  16. DESDynI Quad First Stage Processor - A Four Channel Digitizer and Digital Beam Forming Processor

    Science.gov (United States)

    Chuang, Chung-Lun; Shaffer, Scott; Smythe, Robert; Niamsuwan, Noppasin; Li, Samuel; Liao, Eric; Lim, Chester; Morfopolous, Arin; Veilleux, Louise

    2013-01-01

    The proposed Deformation, Eco-Systems, and Dynamics of Ice Radar (DESDynI-R) L-band SAR instrument employs multiple digital channels to optimize resolution while keeping a large swath on a single pass. High-speed digitization with very fine synchronization and digital beam forming are necessary in order to facilitate this new technique. The Quad First Stage Processor (qFSP) was developed to achieve both the processing performance as well as the digitizing fidelity in order to accomplish this sweeping SAR technique. The qFSP utilizes high precision and high-speed analog to digital converters (ADCs), each with a finely adjustable clock distribution network to digitize the channels at the fidelity necessary to allow for digital beam forming. The Xilinx produced FX130T Virtex 5 part handles the processing to digitally calibrate each channel as well as filter and beam form the receive signals. Demonstrating the digital processing required for digital beam forming and digital calibration is instrumental to the viability of the proposed DESDynI instrument. The qFSP development brings this implementation to Technology Readiness Level (TRL) 6. This paper will detail the design and development of the prototype qFSP as well as the preliminary results from hardware tests.

  17. Determination of Toxic Metals in Little Cigar Tobacco with 'Triple Quad' ICP-MS.

    Science.gov (United States)

    Pappas, R Steven; Martone, Naudia; Gonzalez-Jimenez, Nathalie; Fresquez, Mark R; Watson, Clifford H

    2015-06-01

    Smoking remains the leading cause of preventable death in the USA. Much of the focus on harmful and potentially harmful constituents (HPHCs) in tobacco products has been on cigarettes. Little cigars gained popularity over the last decade until tobacco taxes made cigarettes more expensive in the USA. Many little cigar brands are similar in size with cigarettes and may be smoked in a similar manner. Scant data are available on HPHC concentrations in little cigars, therefore we developed and applied a new analytical method to determine concentrations of 10 toxic metals in little cigar tobacco. The method utilizes 'triple quadrupole' ICP-MS. By optimizing octapole bias, energy discrimination and cell gas flow settings, we were able to accurately quantify a range of elements including those for which the cell gas reactions were endothermic. All standard modes (Single Quad No Gas, MS-MS NH3/He and MS-MS O2) were utilized for the quantitation of 10 toxic metals in little cigar tobacco, including uranium, which was added as an analyte in the new method. Because of the elimination of interfering ions at 'shifted analyte masses', detection limits were lower compared with a previous method. Tobacco selenium concentrations were below the limit of detection in the previous method, but the new technology made it possible to report all selenium concentrations. Published by Oxford University Press 2015. This work is written by (a) US Government employee(s) and is in the public domain in the US.

  18. Optimization of high count rate event counting detector with Microchannel Plates and quad Timepix readout

    Energy Technology Data Exchange (ETDEWEB)

    Tremsin, A.S., E-mail: ast@ssl.berkeley.edu; Vallerga, J.V.; McPhate, J.B.; Siegmund, O.H.W.

    2015-07-01

    Many high resolution event counting devices process one event at a time and cannot register simultaneous events. In this article a frame-based readout event counting detector consisting of a pair of Microchannel Plates and a quad Timepix readout is described. More than 10{sup 4} simultaneous events can be detected with a spatial resolution of ~55 µm, while >10{sup 3} simultaneous events can be detected with <10 µm spatial resolution when event centroiding is implemented. The fast readout electronics is capable of processing >1200 frames/sec, while the global count rate of the detector can exceed 5×10{sup 8} particles/s when no timing information on every particle is required. For the first generation Timepix readout, the timing resolution is limited by the Timepix clock to 10–20 ns. Optimization of the MCP gain, rear field voltage and Timepix threshold levels are crucial for the device performance and that is the main subject of this article. These devices can be very attractive for applications where the photon/electron/ion/neutron counting with high spatial and temporal resolution is required, such as energy resolved neutron imaging, Time of Flight experiments in lidar applications, experiments on photoelectron spectroscopy and many others.

  19. Trajectory optimization of multiple quad-rotor UAVs in collaborative assembling task

    Directory of Open Access Journals (Sweden)

    Chen Yongbo

    2016-02-01

    Full Text Available A hierarchic optimization strategy based on the offline path planning process and online trajectory planning process is presented to solve the trajectory optimization problem of multiple quad-rotor unmanned aerial vehicles in the collaborative assembling task. Firstly, the path planning process is solved by a novel parallel intelligent optimization algorithm, the central force optimization-genetic algorithm (CFO-GA, which combines the central force optimization (CFO algorithm with the genetic algorithm (GA. Because of the immaturity of the CFO, the convergence analysis of the CFO is completed by the stability theory of the linear time-variant discrete-time systems. The results show that the parallel CFO-GA algorithm converges faster than the parallel CFO and the central force optimization-sequential quadratic programming (CFO-SQP algorithm. Then, the trajectory planning problem is established based on the path planning results. In order to limit the range of the attitude angle and guarantee the flight stability, the optimized object is changed from the ordinary six-degree-of-freedom rigid-body dynamic model to the dynamic model with an inner-loop attitude controller. The results show that the trajectory planning process can be solved by the mature SQP algorithm easily. Finally, the discussion and analysis of the real-time performance of the hierarchic optimization strategy are presented around the group number of the waypoints and the equal interval time.

  20. Trajectory optimization of multiple quad-rotor UAVs in collaborative assembling task

    Institute of Scientific and Technical Information of China (English)

    Chen Yongbo; Yu Jianqiao; Mei Yuesong; Zhang Siyu; Ai Xiaolin; Jia Zhenyue

    2016-01-01

    A hierarchic optimization strategy based on the offline path planning process and online trajectory planning process is presented to solve the trajectory optimization problem of multiple quad-rotor unmanned aerial vehicles in the collaborative assembling task. Firstly, the path planning process is solved by a novel parallel intelligent optimization algorithm, the central force optimization-genetic algorithm (CFO-GA), which combines the central force optimization (CFO) algorithm with the genetic algorithm (GA). Because of the immaturity of the CFO, the convergence analysis of the CFO is completed by the stability theory of the linear time-variant discrete-time sys-tems. The results show that the parallel CFO-GA algorithm converges faster than the parallel CFO and the central force optimization-sequential quadratic programming (CFO-SQP) algorithm. Then, the trajectory planning problem is established based on the path planning results. In order to limit the range of the attitude angle and guarantee the flight stability, the optimized object is changed from the ordinary six-degree-of-freedom rigid-body dynamic model to the dynamic model with an inner-loop attitude controller. The results show that the trajectory planning process can be solved by the mature SQP algorithm easily. Finally, the discussion and analysis of the real-time per-formance of the hierarchic optimization strategy are presented around the group number of the waypoints and the equal interval time.

  1. Characterization of the Millimeter-Wave Polarization of Centaurus A with QUaD

    CERN Document Server

    Ade, P; Bowden, M; Brown, M L; Cahill, G; Castro, P G; Church, S; Culverhouse, T; Friedman, R B; Ganga, K; Gear, W K; Gupta, S; Hinderks, J; Kovac, J; Lange, A E; Leitch, E; Melhuish, S J; Memari, Y; Murphy, J A; Orlando, A; O'Sullivan, C; Piccirillo, L; Pryke, C; Rajguru, N; Rusholme, B; Schwarz, R; Taylor, A N; Thompson, K L; Turner, A H; Wu, E Y S

    2009-01-01

    Centaurus (Cen) A represents one of the best candidates for an isolated, compact, highly polarized source that is bright at typical cosmic microwave background (CMB) experiment frequencies. We present measurements of the 4 degree by 2 degree region centered on Cen A with QUaD, a CMB polarimeter whose absolute polarization angle is known to 0.5 degrees. Simulations are performed to assess the effect of misestimation of the instrumental parameters on the final measurement, and systematic errors due to the field's background structure and temporal variability from Cen A's nuclear region are determined. The total (Q, U) of the inner lobe region is (1.00 +/- 0.07 (stat.) +/- 0.04 (sys.), -1.72 +/- 0.06 +/- 0.05) Jy at 100 GHz and (0.80 +/- 0.06 +/- 0.06, -1.40 +/- 0.07 +/- 0.08) Jy at 150 GHz, leading to polarization angles and total errors of -30.0 +/- 1.1 degrees and -29.1 +/- 1.7 degrees. These measurements will allow the use of Cen A as a polarized calibration source for future millimeter experiments.

  2. Optimised Spatial Sampling Scheme for Soil Electriclal Conductivity Based on Variance Quad-Tree(VQT)Method

    Institute of Scientific and Technical Information of China (English)

    LI Yan; SHI Zhou; WU Ci-fang; LI Feng; LI Hong-yi

    2007-01-01

    The acquisition of precise soil data representative of the entire survey area,is a critical issue for many treatments such as irrigation or fertilization in precision agriculture.The aim of this study was to investigate the spatial variability of soil bulk electrical conductivity(ECb)in a coastal saline field and design an optimized spatial sampling scheme of ECb based on a sampling design algorithm,the variance quad-tree(VQT)method.Soil ECb data were collected from the field at 20m interval in a regular grid scheme.The smooth contour map of the whole field was obtained by ordinary kriging interpolation,VQT algorithm was then used to split the smooth contour map into strata of different number desired,the sampling locations can be selected within each stratum in subsequent sampling.The result indicated that the probability of choosing representative sampling sites was increased significantly by using VQT method with the sampling number being greatly reduced compared to grid sampling design while retaining the same prediction accuracy.The advantage of the VQT method is that this scheme samples sparsely in fields where the spatial variability is relatively uniform and more intensive where the variability is large.Thus the sampling efficiency can be improved,hence facilitate an assessment methodology that can be applied in a rapid,practical and cost-effective manner.

  3. DESDynI Quad First Stage Processor - A Four Channel Digitizer and Digital Beam Forming Processor

    Science.gov (United States)

    Chuang, Chung-Lun; Shaffer, Scott; Smythe, Robert; Niamsuwan, Noppasin; Li, Samuel; Liao, Eric; Lim, Chester; Morfopolous, Arin; Veilleux, Louise

    2013-01-01

    The proposed Deformation, Eco-Systems, and Dynamics of Ice Radar (DESDynI-R) L-band SAR instrument employs multiple digital channels to optimize resolution while keeping a large swath on a single pass. High-speed digitization with very fine synchronization and digital beam forming are necessary in order to facilitate this new technique. The Quad First Stage Processor (qFSP) was developed to achieve both the processing performance as well as the digitizing fidelity in order to accomplish this sweeping SAR technique. The qFSP utilizes high precision and high-speed analog to digital converters (ADCs), each with a finely adjustable clock distribution network to digitize the channels at the fidelity necessary to allow for digital beam forming. The Xilinx produced FX130T Virtex 5 part handles the processing to digitally calibrate each channel as well as filter and beam form the receive signals. Demonstrating the digital processing required for digital beam forming and digital calibration is instrumental to the viability of the proposed DESDynI instrument. The qFSP development brings this implementation to Technology Readiness Level (TRL) 6. This paper will detail the design and development of the prototype qFSP as well as the preliminary results from hardware tests.

  4. Reactor Vessel Surveillance Program for Advanced Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Kyeong-Hoon; Kim, Tae-Wan; Lee, Gyu-Mahn; Kim, Jong-Wook; Park, Keun-Bae; Kim, Keung-Koo

    2008-10-15

    This report provides the design requirements of an integral type reactor vessel surveillance program for an integral type reactor in accordance with the requirements of Korean MEST (Ministry of Education, Science and Technology Development) Notice 2008-18. This report covers the requirements for the design of surveillance capsule assemblies including their test specimens, test block materials, handling tools, and monitors of the surveillance capsule neutron fluence and temperature. In addition, this report provides design requirements for the program for irradiation surveillance of reactor vessel materials, a layout of specimens and monitors in the surveillance capsule, procedures of installation and retrieval of the surveillance capsule assemblies, and the layout of the surveillance capsule assemblies in the reactor.

  5. SNTP program reactor design

    Science.gov (United States)

    Walton, Lewis A.; Sapyta, Joseph J.

    1993-06-01

    The Space Nuclear Thermal Propulsion (SNTP) program is evaluating the feasibility of a particle bed reactor for a high-performance nuclear thermal rocket engine. Reactors operating between 500 MW and 2,000 MW will produce engine thrusts ranging from 20,000 pounds to 80,000 pounds. The optimum reactor arrangement depends on the power level desired and the intended application. The key components of the reactor have been developed and are being tested. Flow-to-power matching considerations dominate the thermal-hydraulic design of the reactor. Optimal propellant management during decay heat cooling requires a three-pronged approach. Adequate computational methods exist to perform the neutronics analysis of the reactor core. These methods have been benchmarked to critical experiment data.

  6. Hybrid reactors. [Fuel cycle

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R.W.

    1980-09-09

    The rationale for hybrid fusion-fission reactors is the production of fissile fuel for fission reactors. A new class of reactor, the fission-suppressed hybrid promises unusually good safety features as well as the ability to support 25 light-water reactors of the same nuclear power rating, or even more high-conversion-ratio reactors such as the heavy-water type. One 4000-MW nuclear hybrid can produce 7200 kg of /sup 233/U per year. To obtain good economics, injector efficiency times plasma gain (eta/sub i/Q) should be greater than 2, the wall load should be greater than 1 MW.m/sup -2/, and the hybrid should cost less than 6 times the cost of a light-water reactor. Introduction rates for the fission-suppressed hybrid are usually rapid.

  7. Fast Spectrum Reactors

    CERN Document Server

    Todd, Donald; Tsvetkov, Pavel

    2012-01-01

    Fast Spectrum Reactors presents a detailed overview of world-wide technology contributing to the development of fast spectrum reactors. With a unique focus on the capabilities of fast spectrum reactors to address nuclear waste transmutation issues, in addition to the well-known capabilities of breeding new fuel, this volume describes how fast spectrum reactors contribute to the wide application of nuclear power systems to serve the global nuclear renaissance while minimizing nuclear proliferation concerns. Readers will find an introduction to the sustainable development of nuclear energy and the role of fast reactors, in addition to an economic analysis of nuclear reactors. A section devoted to neutronics offers the current trends in nuclear design, such as performance parameters and the optimization of advanced power systems. The latest findings on fuel management, partitioning and transmutation include the physics, efficiency and strategies of transmutation, homogeneous and heterogeneous recycling, in addit...

  8. LMFBR type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kanbe, Mitsuru

    1997-04-04

    An LMFBR type reactor comprises a plurality of reactor cores in a reactor container. Namely, a plurality of pot containing vessels are disposed in the reactor vessel and a plurality of reactor cores are formed in a state where an integrated-type fuel assembly is each inserted to a pot, and a coolant pipeline is connected to each of the pot containing-vessel to cool the reactor core respectively. When fuels are exchanged, the integrated-type fuel assembly is taken out together with the pot from the reactor vessel in a state where the integrated-type fuel assembly is immersed in the coolants in the pot as it is. Accordingly, coolants are supplied to each of the pot containing-vessel connected with the coolant pipeline and circulate while cooling the integrated-type fuel assembly for every pot. Then, when the fuels are exchanged, the integrated type fuel assembly is taken out to the outside of the reactor together with the pot by taking up the pot from the pot-containing vessel. Then, neutron economy is improved to thereby improve reactor power and the breeding ratio. (N.H.)

  9. INVAP's Research Reactor Designs

    Directory of Open Access Journals (Sweden)

    Eduardo Villarino

    2011-01-01

    Full Text Available INVAP, an Argentine company founded more than three decades ago, is today recognized as one of the leaders within the research reactor industry. INVAP has participated in several projects covering a wide range of facilities, designed in accordance with the requirements of our different clients. For complying with these requirements, INVAP developed special skills and capabilities to deal with different fuel assemblies, different core cooling systems, and different reactor layouts. This paper summarizes the general features and utilization of several INVAP research reactor designs, from subcritical and critical assemblies to high-power reactors.

  10. Multi purpose research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Raina, V.K. [Research Reactor Design and Projects Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)]. E-mail: vkrain@magnum.barc.ernet.in; Sasidharan, K. [Research Reactor Design and Projects Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Sengupta, Samiran [Research Reactor Design and Projects Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Singh, Tej [Research Reactor Services Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2006-04-15

    At present Dhruva and Cirus reactors provide the majority of research reactor based facilities to cater to the various needs of a vast pool of researchers in the field of material sciences, physics, chemistry, bio sciences, research and development work for nuclear power plants and production of radio isotopes. With a view to further consolidate and expand the scope of research and development in nuclear and allied sciences, a new 20 MWt multi purpose research reactor is being designed. This paper describes some of the design features and safety aspects of this reactor.

  11. Measles-mumps-rubella-varicella combination vaccine (ProQuad): a guide to its use in children in the E.U.

    Science.gov (United States)

    Scott, Lesley J

    2015-04-01

    In the EU, the live attenuated, tetravalent measles-mumps-rubella-varicella vaccine ProQuad is indicated for simultaneous vaccination against measles, mumps, rubella and varicella in individuals from 12 months of age using a two-dose schedule and may be used in infants from 9 months of age to conform with a national vaccination schedule, outbreak situations or travel to a region with a high prevalence of measles. Clinical data in young children indicates that vaccination with ProQuad is as immunogenic as the component vaccines, provides long-term protection against these potentially serious childhood infections and has an acceptable safety profile. Combining the viral strains of the measles-mumps-rubella vaccine M-M-RVAXPRO and the varicella vaccine Varivax in ProQuad reduces the complexity of vaccination schedules, thereby potentially improving vaccination coverage and the timeliness of vaccination.

  12. Quad-barrel multifunctional electrochemical and ion conductance probe for voltammetric analysis and imaging.

    Science.gov (United States)

    Nadappuram, Binoy Paulose; McKelvey, Kim; Byers, Joshua C; Güell, Aleix G; Colburn, Alex W; Lazenby, Robert A; Unwin, Patrick R

    2015-04-07

    The fabrication and use of a multifunctional electrochemical probe incorporating two independent carbon working electrodes and two electrolyte-filled barrels, equipped with quasi-reference counter electrodes (QRCEs), in the end of a tapered micrometer-scale pipet is described. This "quad-probe" (4-channel probe) was fabricated by depositing carbon pyrolytically into two diagonally opposite barrels of a laser-pulled quartz quadruple-barrelled pipet. After filling the open channels with electrolyte solution, a meniscus forms at the end of the probe and covers the two working electrodes. The two carbon electrodes can be used to drive local electrochemical reactions within the meniscus while a bias between the QRCEs in the electrolyte channels provides an ion conductance signal that is used to control and position the meniscus on a surface of interest. When brought into contact with a surface, localized high resolution amperometric imaging can be achieved with the two carbon working electrodes with a spatial resolution defined by the meniscus contact area. The substrate can be an insulating material or (semi)conductor, but herein, we focus mainly on conducting substrates that can be connected as a third working electrode. Studies using both aqueous and ionic liquid electrolytes in the probe, together with gold and individual single walled carbon nanotube samples, demonstrate the utility of the technique. Substrate generation-dual tip collection measurements are shown to be characterized by high collection efficiencies (approaching 100%). This hybrid configuration of scanning electrochemical microscopy (SECM) and scanning electrochemical cell microscopy (SECCM) should be powerful for future applications in electrode mapping, as well as in studies of insulating materials as demonstrated by transient spot redox-titration measurements at an electrostatically charged Teflon surface and at a pristine calcite surface, where a functionalized probe is used to follow the

  13. 0.4-1.2 GHz hybrid Al-CFRP open-boundary quad-ridge horn

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    We present a 0.4-1.2 GHz open-boundary quad-ridge horn to be used as a wide-band probe at the DTU-ESA Spherical Near-Field Antenna Test Facility at the Technical University of Denmark (DTU). Due to adopted hybrid Al-CFRP fabrication technology, the weight of the probe is reduced by a factor of 2.......3 as compared to the case of the same probe fabricated of solid aluminum. Measured characteristics of the probe as well as its performance with respect to the higher-order probe correction technique are presented and discussed....

  14. Identification of stability and control derivatives for AS 355 L2 helicopter with Quad-M/CTA methodology

    Science.gov (United States)

    de Oliveira, Sérgio Servilha; Menegaldo, Luciano Luporini

    2012-11-01

    This work presents results obtained from a study of case for H-55 Helicopter System Identification which was carried out by an implementation of Quad-M Methodology purposed for Jategaonkar. The implementation performed was based on Cruz et al whose works were developed in Centro Técnico Aeroespacial (CTA). A comparison between Stability and Control Derivatives tables from these results and those from literature is performed for some important flight conditions. This comparison allows us to conclude about the reliability of the method, to present preliminary SCD tables for the studied aircraft and point to possible future works.

  15. The influence of weak lensing on measurements of the Hubble constant with quad-image gravitational lenses

    OpenAIRE

    2016-01-01

    We investigate the influence of matter along the line of sight and in the strong lens vicinity on the properties of quad image configurations and on the measurements of the Hubble constant (H0). We use simulations of light propagation in a nonuniform universe model with the distribution of matter in space based on the data from Millennium Simulation. For a given strong lens and haloes in its environment we model the matter distribution along the line of sight many times, using different combi...

  16. Design of Novel S-Shaped Quad-Band Antenna for MedRadio/WMTS/ISM Implantable Biotelemetry Applications

    OpenAIRE

    2012-01-01

    A novel S-shaped quad-band planar inverted-F antenna (PIFA) is proposed for implantable biotelemetry in the Medical Device Radiocommunications Service (MedRadio) band (401–406 MHz), Wireless Medical Telemetry Service (WMTS) band (1427–1432 MHz), and industrial, scientific, and medical (ISM) bands (433-434 MHz and 2.4–2.4835 GHz). The proposed antenna reveals compact dimension of 254 mm3 (10×10×2.45 mm3) and is composed of three substrates and a superstrate, which are constructed from an S-sha...

  17. Reactor Materials Research

    Energy Technology Data Exchange (ETDEWEB)

    Van Walle, E

    2001-04-01

    The activities of the Reactor Materials Research Department of the Belgian Nuclear Research Centre SCK-CEN in 2000 are summarised. The programmes within the department are focussed on studies concerning (1) fusion, in particular mechanical testing; (2) Irradiation Assisted Stress Corrosion Cracking (IASCC); (3) nuclear fuel; and (4) Reactor Pressure Vessel Steel (RPVS)

  18. Space Nuclear Reactor Engineering

    Energy Technology Data Exchange (ETDEWEB)

    Poston, David Irvin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-06

    We needed to find a space reactor concept that could be attractive to NASA for flight and proven with a rapid turnaround, low-cost nuclear test. Heat-pipe-cooled reactors coupled to Stirling engines long identified as the easiest path to near-term, low-cost concept.

  19. Light water reactor program

    Energy Technology Data Exchange (ETDEWEB)

    Franks, S.M.

    1994-12-31

    The US Department of Energy`s Light Water Reactor Program is outlined. The scope of the program consists of: design certification of evolutionary plants; design, development, and design certification of simplified passive plants; first-of-a-kind engineering to achieve commercial standardization; plant lifetime improvement; and advanced reactor severe accident program. These program activities of the Office of Nuclear Energy are discussed.

  20. Status of French reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ballagny, A. [Commissariat a l`Energie Atomique, Saclay (France)

    1997-08-01

    The status of French reactors is reviewed. The ORPHEE and RHF reactors can not be operated with a LEU fuel which would be limited to 4.8 g U/cm{sup 3}. The OSIRIS reactor has already been converted to LEU. It will use U{sub 3}Si{sub 2} as soon as its present stock of UO{sub 2} fuel is used up, at the end of 1994. The decision to close down the SILOE reactor in the near future is not propitious for the start of a conversion process. The REX 2000 reactor, which is expected to be commissioned in 2005, will use LEU (except if the fast neutrons core option is selected). Concerning the end of the HEU fuel cycle, the best option is reprocessing followed by conversion of the reprocessed uranium to LEU.

  1. Nuclear reactor design

    CERN Document Server

    2014-01-01

    This book focuses on core design and methods for design and analysis. It is based on advances made in nuclear power utilization and computational methods over the past 40 years, covering core design of boiling water reactors and pressurized water reactors, as well as fast reactors and high-temperature gas-cooled reactors. The objectives of this book are to help graduate and advanced undergraduate students to understand core design and analysis, and to serve as a background reference for engineers actively working in light water reactors. Methodologies for core design and analysis, together with physical descriptions, are emphasized. The book also covers coupled thermal hydraulic core calculations, plant dynamics, and safety analysis, allowing readers to understand core design in relation to plant control and safety.

  2. Mirror reactor surface study

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, A. L.; Damm, C. C.; Futch, A. H.; Hiskes, J. R.; Meisenheimer, R. G.; Moir, R. W.; Simonen, T. C.; Stallard, B. W.; Taylor, C. E.

    1976-09-01

    A general survey is presented of surface-related phenomena associated with the following mirror reactor elements: plasma first wall, ion sources, neutral beams, director converters, vacuum systems, and plasma diagnostics. A discussion of surface phenomena in possible abnormal reactor operation is included. Several studies which appear to merit immediate attention and which are essential to the development of mirror reactors are abstracted from the list of recommended areas for surface work. The appendix contains a discussion of the fundamentals of particle/surface interactions. The interactions surveyed are backscattering, thermal desorption, sputtering, diffusion, particle ranges in solids, and surface spectroscopic methods. A bibliography lists references in a number of categories pertinent to mirror reactors. Several complete published and unpublished reports on surface aspects of current mirror plasma experiments and reactor developments are also included.

  3. Water distribuition characteristics and soil loss of LEPA Quad-Spray emitter nozzles Características de distribuição de água e perdas de solo de bocais do emissor Quad-Spray tipo LEPA

    Directory of Open Access Journals (Sweden)

    Moises S. Ribeiro

    2013-04-01

    Full Text Available The objective of this study was to characterize water application rate, water application pattern width, flow rate, water distribution uniformity and soil loss caused by nozzles of the Low Energy Precision Aplication (LEPA type Quad-Spray emitter. The study was carried out at the Hydraulic and Irrigation Laboratory of the Department of Engineering at the Federal University of Lavras, in Lavras, state of Minas Gerais - MG, Brazil. Twenty-two (22 LEPA Quad-Spray emitter nozzles were evaluated, with nozzle diameter ranging from 1.59 to 9.92 mm. The experimental design used was entirely randomized, with three replications.Increasing values of nozzle flow rate ranging from 77.44 up to 3,044 L h-1, were obtained with increasing nozzle diameter sizes. Application pattern width ranged from 0.56 up to 3.24m, according to nozzles diameter size. Low values of CDU (maximum of 35.73% were observed when using the Quad-Spray nozzles. Observed average water application rates covered the range between 68.05 mm h-1 (the lowest value that was obtained with the 2.38mm nozzle and 258.15 mm h-1 (the highest value that was observed with the 9.92 mm. Average water application rates increased in a simple non-linear function with the increase of nozzle size diameter. However, the weighted average increase in the amount of soil loss by erosion was not related to the increase of weighted average water application values.Foi objetivo deste trabalho caracterizar a taxa de aplicação de água, largura do padrão molhado, vazão, uniformidade de distribuição de água e perdas de solo de bocais do emissor Quad-Spray tipo Low Energy Precision Aplication (LEPA. O trabalho foi realizado no Laboratório de Hidráulica e Irrigação (LHI, do Departamento de Engenharia (DEG, na Universidade Federal de Lavras (UFLA, Lavras - MG. Foram avaliados 22 bocais com diâmetro de bocal variando de 1,59 a 9,92 mm. O delineamento experimental estatístico foi o inteiramente casualizado, com

  4. Is workplace satisfaction associated with self-reported quad bike loss of control events among farm workers in New Zealand?

    Science.gov (United States)

    Clay, Lynne; Treharne, Gareth J; Hay-Smith, E Jean C; Milosavljevic, Stephan

    2014-05-01

    This study investigated whether rural workers who have higher workplace satisfaction are less likely to report quad bike loss of control events (LCEs). Two independent samples of farmers completed a survey regarding LCEs and workplace satisfaction. In the first sample (n = 130) analysis revealed no relationship (p = 0.74) between workplace satisfaction and LCEs but lower rates of LCEs were reported by employees (IRR 0.52, 95%CI 0.31-0.86) compared to self-employed participants. In the second sample (n = 112), workplace satisfaction was weakly related to LCEs (IRR 1.04, 95%CI 1.00, to 1.09) with participants who found their job more psychologically demanding more likely to have had an LCE (IRR 1.14, 95%CI 1.05-1.23). Exploring the role of psychological demands on safety behaviour with respect to quad bike use, may help to address this important safety issue. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  5. The influence of weak lensing on measurements of the Hubble constant with quad-image gravitational lenses

    CERN Document Server

    Jaroszynski, M

    2016-01-01

    We investigate the influence of matter along the line of sight and in the strong lens vicinity on the properties of quad image configurations and on the measurements of the Hubble constant (H0). We use simulations of light propagation in a nonuniform universe model with the distribution of matter in space based on the data from Millennium Simulation. For a given strong lens and haloes in its environment we model the matter distribution along the line of sight many times, using different combinations of precomputed deflection maps representing subsequent layers of matter on the path of rays. We fit the simulated quad image configurations with time delays using nonsingular isothermal ellipsoids (NSIE) with external shear as lens models, treating the Hubble constant as a free parameter. We get a large artificial catalog of lenses with derived values of the Hubble constant, Hfit. The average and median of Hfit differ from the true value used in simulations by < 0.5 km/s/Mpc which includes the influence of matt...

  6. The influence of weak lensing on measurements of the Hubble constant with quad-image gravitational lenses

    Science.gov (United States)

    Jaroszyński, M.; Skowron, J.

    2016-10-01

    We investigate the influence of matter along the line of sight and in the strong lens vicinity on the properties of quad-image configurations and on the measurements of the Hubble constant (H0). We use simulations of light propagation in a non-uniform universe model with the distribution of matter in space based on the data from Millennium Simulation. For a given strong lens and haloes in its environment we model the matter distribution along the line of sight many times, using different combinations of pre-computed deflection maps representing subsequent layers of matter on the path of rays. We fit the simulated quad-image configurations with time delays using non-singular isothermal ellipsoids with external shear as lens models, treating the Hubble constant as a free parameter. We get a large artificial catalogue of lenses with derived values of the Hubble constant, Hfit. The average and median of Hfit differ from the true value used in simulations by ≤0.5 km s-1 Mpc-1 which includes the influence of matter along the line of sight and in the lens vicinity, and uncertainty in lens parameters, except the slope of the matter distribution, which is fixed. The characteristic uncertainty of Hfit is ˜3 km s-1 Mpc-1. Substituting the lens shear parameters with values estimated from the simulations reduces the uncertainty to ˜2 km s-1 Mpc-1.

  7. Slurry reactor design studies

    Energy Technology Data Exchange (ETDEWEB)

    Fox, J.M.; Degen, B.D.; Cady, G.; Deslate, F.D.; Summers, R.L. (Bechtel Group, Inc., San Francisco, CA (USA)); Akgerman, A. (Texas A and M Univ., College Station, TX (USA)); Smith, J.M. (California Univ., Davis, CA (USA))

    1990-06-01

    The objective of these studies was to perform a realistic evaluation of the relative costs of tublar-fixed-bed and slurry reactors for methanol, mixed alcohols and Fischer-Tropsch syntheses under conditions where they would realistically be expected to operate. The slurry Fischer-Tropsch reactor was, therefore, operated at low H{sub 2}/CO ratio on gas directly from a Shell gasifier. The fixed-bed reactor was operated on 2.0 H{sub 2}/CO ratio gas after adjustment by shift and CO{sub 2} removal. Every attempt was made to give each reactor the benefit of its optimum design condition and correlations were developed to extend the models beyond the range of the experimental pilot plant data. For the methanol design, comparisons were made for a recycle plant with high methanol yield, this being the standard design condition. It is recognized that this is not necessarily the optimum application for the slurry reactor, which is being proposed for a once-through operation, coproducing methanol and power. Consideration is also given to the applicability of the slurry reactor to mixed alcohols, based on conditions provided by Lurgi for an Octamix{trademark} plant using their standard tubular-fixed reactor technology. 7 figs., 26 tabs.

  8. Precise orbit determination for quad-constellation satellites at Wuhan University: strategy, result validation, and comparison

    Science.gov (United States)

    Guo, Jing; Xu, Xiaolong; Zhao, Qile; Liu, Jingnan

    2016-02-01

    This contribution summarizes the strategy used by Wuhan University (WHU) to determine precise orbit and clock products for Multi-GNSS Experiment (MGEX) of the International GNSS Service (IGS). In particular, the satellite attitude, phase center corrections, solar radiation pressure model developed and used for BDS satellites are addressed. In addition, this contribution analyzes the orbit and clock quality of the quad-constellation products from MGEX Analysis Centers (ACs) for a common time period of 1 year (2014). With IGS final GPS and GLONASS products as the reference, Multi-GNSS products of WHU (indicated by WUM) show the best agreement among these products from all MGEX ACs in both accuracy and stability. 3D Day Boundary Discontinuities (DBDs) range from 8 to 27 cm for Galileo-IOV satellites among all ACs' products, whereas WUM ones are the largest (about 26.2 cm). Among three types of BDS satellites, MEOs show the smallest DBDs from 10 to 27 cm, whereas the DBDs for all ACs products are at decimeter to meter level for GEOs and one to three decimeter for IGSOs, respectively. As to the satellite laser ranging (SLR) validation for Galileo-IOV satellites, the accuracy evaluated by SLR residuals is at the one decimeter level with the well-known systematic bias of about -5 cm for all ACs. For BDS satellites, the accuracy could reach decimeter level, one decimeter level, and centimeter level for GEOs, IGSOs, and MEOs, respectively. However, there is a noticeable bias in GEO SLR residuals. In addition, systematic errors dependent on orbit angle related to mismodeled solar radiation pressure (SRP) are present for BDS GEOs and IGSOs. The results of Multi-GNSS combined kinematic PPP demonstrate that the best accuracy of position and fastest convergence speed have been achieved using WUM products, particularly in the Up direction. Furthermore, the accuracy of static BDS only PPP degrades when the BDS IGSO and MEO satellites switches to orbit-normal orientation

  9. Fast Breeder Reactor studies

    Energy Technology Data Exchange (ETDEWEB)

    Till, C.E.; Chang, Y.I.; Kittel, J.H.; Fauske, H.K.; Lineberry, M.J.; Stevenson, M.G.; Amundson, P.I.; Dance, K.D.

    1980-07-01

    This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts.

  10. Gas cooled fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1972-06-01

    Although most of the development work on fast breeder reactors has been devoted to the use of liquid metal cooling, interest has been expressed for a number of years in alternative breeder concepts using other coolants. One of a number of concepts in which interest has been retained is the Gas-Cooled Fast Reactor (GCFR). As presently envisioned, it would operate on the uranium-plutonium mixed oxide fuel cycle, similar to that used in the Liquid Metal Fast Breeder Reactor (LMFBR), and would use helium gas as the coolant.

  11. Microfluidic electrochemical reactors

    Science.gov (United States)

    Nuzzo, Ralph G [Champaign, IL; Mitrovski, Svetlana M [Urbana, IL

    2011-03-22

    A microfluidic electrochemical reactor includes an electrode and one or more microfluidic channels on the electrode, where the microfluidic channels are covered with a membrane containing a gas permeable polymer. The distance between the electrode and the membrane is less than 500 micrometers. The microfluidic electrochemical reactor can provide for increased reaction rates in electrochemical reactions using a gaseous reactant, as compared to conventional electrochemical cells. Microfluidic electrochemical reactors can be incorporated into devices for applications such as fuel cells, electrochemical analysis, microfluidic actuation, pH gradient formation.

  12. Isolated/Non-Isolated Quad-Inverter Configuration for Multilevel Symmetrical/Asymmetrical Dual Six-Phase Star-Winding Converter

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Hontz, Michael R.; Khanna, Raghav

    2016-01-01

    This article presents the developments of a novel isolated/non-isolated quad inverter configuration for multilevel dual six-phase (twelve-phase) star-winding converter. The modular circuit consists of four standard voltage source inverters (VSIs). Each VSI is incorporated with one bi-directional ...

  13. A ‘quad-phantom’ film dosimeter for use as a multi-planar verification tool for PRESAGE/optical-CT

    Science.gov (United States)

    Stunja, L; Thomas, A; Adamovics, J; Deasy, J; Oldham, M

    2010-01-01

    Introduction To develop and characterize the accuracy and reproducibility of a quad-phantom dosimeter which will serve as an independent verification tool during commissioning of a PRESAGE/optical-CT 3D dosimetry system. Methods A 16cm × 12cm cylindrical quad-phantom was constructed from four pieces of solid polyurethane mimicking the PRESAGE material. Films were placed and anchored in orthogonal planes and the quad-phantom was fastened tightly together and placed in a water-filled Styrofoam container for irradiation. A simple, two-field plan consisting of 6×6cm anterior-posterior and right-lateral 6MV photon beams (400cGy) was delivered three times (fresh films inserted for each) with a Varian Clinac 600C. Image registration was performed in the Computational Environment for Radiological Research (CERR) and dose profiles and gamma analysis was performed in CERR and MATLAB. Results & Discussion Excellent reproducibility was observed during the irradiations, with ~2.3% standard deviation between all pixels. Using a 3%, 3mm gamma criteria, excellent dosimetric accuracy was observed, with 98.8% and 96.3% passing rates in the sagittal and axial planes, respectively. Conclusion The preliminary results indicate that the quad-phantom can serve as a reproducible and accurate system for high resolution dosimetry in orthogonal planes and should serve as an effective verification tool for PRESAGE/optical-CT in more challenging clinical scenarios. PMID:21218141

  14. A 'quad-phantom' film dosimeter for use as a multi-planar verification tool for PRESAGE/optical-CT

    Energy Technology Data Exchange (ETDEWEB)

    Stunja, L; Thomas, A; Adamovics, J; Deasy, J; Oldham, M, E-mail: les34@duke.ed

    2010-11-01

    Introduction: To develop and characterize the accuracy and reproducibility of a 'quad-phantom' dosimeter which will serve as an independent verification tool during commissioning of a PRESAGE/optical-CT 3D dosimetry system. Methods: A 16cm x 12cm cylindrical quad-phantom was constructed from four pieces of solid polyurethane mimicking the PRESAGE material. Films were placed and anchored in orthogonal planes and the quad-phantom was fastened tightly together and placed in a water-filled Styrofoam container for irradiation. A simple, two-field plan consisting of 6x6cm anterior-posterior and right-lateral 6 MV photon beams (400 cGy) was delivered three times (fresh films inserted for each) with a Varian Clinac 600C. Image registration was performed in the Computational Environment for Radiological Research (CERR) and dose profiles and gamma analysis was performed in CERR and MATLAB. Results and Discussion: Excellent reproducibility was observed during the irradiations, with {approx}2.3% standard deviation between all pixels. Using a 3%, 3mm gamma criteria, excellent dosimetric accuracy was observed, with 98.8% and 96.3% passing rates in the sagittal and axial planes, respectively. Conclusion: The preliminary results indicate that the quad-phantom can serve as a reproducible and accurate system for high resolution dosimetry in orthogonal planes and should serve as an effective verification tool for PRESAGE/optical-CT in more challenging clinical scenarios.

  15. Fusion Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2002-04-01

    The objective of SCK-CEN's programme on fusion reactor materials is to contribute to the knowledge on the radiation-induced behaviour of fusion reactor materials and components as well as to help the international community in building the scientific and technical basis needed for the construction of the future reactor. Ongoing projects include: the study of the mechanical and chemical (corrosion) behaviour of structural materials under neutron irradiation and water coolant environment; the investigation of the characteristics of irradiated first wall material such as beryllium; investigations on the management of materials resulting from the dismantling of fusion reactors including waste disposal. Progress and achievements in these areas in 2001 are discussed.

  16. New reactor type proposed

    CERN Multimedia

    2003-01-01

    "Russian scientists at the Research Institute of Nuclear Power Engineering in Moscow are hoping to develop a new reactor that will use lead and bismuth as fuel instead of uranium and plutonium" (1/2 page).

  17. Reactor Neutrino Spectra

    CERN Document Server

    Hayes, A C

    2016-01-01

    We present a review of the antineutrino spectra emitted from reactors. Knowledge of these and their associated uncertainties are crucial for neutrino oscillation studies. The spectra used to-date have been determined by either conversion of measured electron spectra to antineutrino spectra or by summing over all of the thousands of transitions that makeup the spectra using modern databases as input. The uncertainties in the subdominant corrections to beta-decay plague both methods, and we provide estimates of these uncertainties. Improving on current knowledge of the antineutrino spectra from reactors will require new experiments. Such experiments would also address the so-called reactor neutrino anomaly and the possible origin of the shoulder observed in the antineutrino spectra measured in recent high-statistics reactor neutrino experiments.

  18. Reactor BR2. Introduction

    Energy Technology Data Exchange (ETDEWEB)

    Gubel, P

    2001-04-01

    The BR2 is a materials testing reactor and is still one of SCK-CEN's important nuclear facilities. After an extensive refurbishment to compensate for the ageing of the installation, the reactor was restarted in April 1997. During the last three years, the availability of the installation was maintained at an average level of 97.6 percent. In the year 2000, the reactor was operated for a total of 104 days at a mean power of 56 MW. In 2000, most irradiation experiments were performed in the CALLISTO PWR loop. The report describes irradiations achieved or under preparation in 2000, including the development of advanced facilities and concept studies for new programmes. An overview of the scientific irradiation programmes as well as of the R and D programme of the BR2 reactor in 2000 is given.

  19. Future Reactor Experiments

    OpenAIRE

    He, Miao

    2013-01-01

    The measurement of the neutrino mixing angle $\\theta_{13}$ opens a gateway for the next generation experiments to measure the neutrino mass hierarchy and the leptonic CP-violating phase. Future reactor experiments will focus on mass hierarchy determination and the precision measurement of mixing parameters. Mass hierarchy can be determined from the disappearance of reactor electron antineutrinos based on the interference effect of two separated oscillation modes. Relative and absolute measure...

  20. Reactor Neutrino Experiments

    OpenAIRE

    Cao, Jun

    2007-01-01

    Precisely measuring $\\theta_{13}$ is one of the highest priority in neutrino oscillation study. Reactor experiments can cleanly determine $\\theta_{13}$. Past reactor neutrino experiments are reviewed and status of next precision $\\theta_{13}$ experiments are presented. Daya Bay is designed to measure $\\sin^22\\theta_{13}$ to better than 0.01 and Double Chooz and RENO are designed to measure it to 0.02-0.03. All are heading to full operation in 2010. Recent improvements in neutrino moment measu...

  1. Department of Reactor Technology

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The general development of the Department of Reactor Technology at Risø during 1981 is presented, and the activities within the major subject fields are described in some detail. Lists of staff, publications, and computer programs are included.......The general development of the Department of Reactor Technology at Risø during 1981 is presented, and the activities within the major subject fields are described in some detail. Lists of staff, publications, and computer programs are included....

  2. Helias reactor studies

    Energy Technology Data Exchange (ETDEWEB)

    Beidler, C.D. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Grieger, G. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Harmeyer, E. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Kisslinger, J. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Karulin, N. [Nuclear Fusion Institute, Moscow (Russian Federation); Maurer, W. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany); Nuehrenberg, J. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Rau, F. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Sapper, J. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany); Wobig, H. [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany)

    1995-10-01

    The present status of Helias reactor studies is characterised by the identification and investigation of specific issues which result from the particular properties of this type of stellarator. On the technical side these are issues related to the coil system, while physics studies have concentrated on confinement, alpha-particle behaviour and ignition conditions. The usual assumptions have been made in those fields which are common to all toroidal fusion reactors: blanket and shield, refuelling and exhaust, safety and economic aspects. For blanket and shield sufficient space has been provided, a detailed concept will be developed in future. To date more emphasis has been placed on scoping and parameter studies as opposed to fixing a specific set of parameters and providing a detailed point study. One result of the Helias reactor studies is that physical dimensions are on the same order as those of tokamak reactors. However, it should be noticed that this comparison is difficult in view of the large spectrum of tokamak reactors ranging from a small reactor like Aries, to a large device such as SEAFP. The notion that the large aspect ratio of 10 or more in Helias configurations also leads to large reactors is misleading, since the large major radius of 22 m is compensated by the average plasma radius of 1.8 m and the average coil radius of 5 m. The plasma volume of 1400 m{sup 3} is about the same as the ITER reactor and the magnetic energy of the coil system is about the same or even slightly smaller than envisaged in ITER. (orig.)

  3. INVAP's Research Reactor Designs

    OpenAIRE

    Eduardo Villarino; Alicia Doval

    2011-01-01

    INVAP, an Argentine company founded more than three decades ago, is today recognized as one of the leaders within the research reactor industry. INVAP has participated in several projects covering a wide range of facilities, designed in accordance with the requirements of our different clients. For complying with these requirements, INVAP developed special skills and capabilities to deal with different fuel assemblies, different core cooling systems, and different reactor layouts. This paper ...

  4. The reactor antineutrino anomalies

    Energy Technology Data Exchange (ETDEWEB)

    Haser, Julia; Buck, Christian; Lindner, Manfred [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany)

    2016-07-01

    Major discoveries were made in the past few years in the field of neutrino flavour oscillation. Nuclear reactors produce a clean and intense flux of electron antineutrinos and are thus an essential neutrino source for the determination of oscillation parameters. Most currently the reactor antineutrino experiments Double Chooz, Daya Bay and RENO have accomplished to measure θ{sub 13}, the smallest of the three-flavour mixing angles. In the course of these experiments two anomalies emerged: (1) the reanalysis of the reactor predictions revealed a deficit in experimentally observed antineutrino flux, known as the ''reactor antineutrino anomaly''. (2) The high precision of the latest generation of neutrino experiments resolved a spectral shape distortion relative to the expected energy spectra. Both puzzles are yet to be solved and triggered new experimental as well as theoretical studies, with the search for light sterile neutrinos as most popular explanation for the flux anomaly. This talk outlines the two reactor antineutrino anomalies. Discussing possible explanations for their occurrence, recent and upcoming efforts to solve the reactor puzzles are highlighted.

  5. Moon base reactor system

    Science.gov (United States)

    Chavez, H.; Flores, J.; Nguyen, M.; Carsen, K.

    1989-01-01

    The objective of our reactor design is to supply a lunar-based research facility with 20 MW(e). The fundamental layout of this lunar-based system includes the reactor, power conversion devices, and a radiator. The additional aim of this reactor is a longevity of 12 to 15 years. The reactor is a liquid metal fast breeder that has a breeding ratio very close to 1.0. The geometry of the core is cylindrical. The metallic fuel rods are of beryllium oxide enriched with varying degrees of uranium, with a beryllium core reflector. The liquid metal coolant chosen was natural lithium. After the liquid metal coolant leaves the reactor, it goes directly into the power conversion devices. The power conversion devices are Stirling engines. The heated coolant acts as a hot reservoir to the device. It then enters the radiator to be cooled and reenters the Stirling engine acting as a cold reservoir. The engines' operating fluid is helium, a highly conductive gas. These Stirling engines are hermetically sealed. Although natural lithium produces a lower breeding ratio, it does have a larger temperature range than sodium. It is also corrosive to steel. This is why the container material must be carefully chosen. One option is to use an expensive alloy of cerbium and zirconium. The radiator must be made of a highly conductive material whose melting point temperature is not exceeded in the reactor and whose structural strength can withstand meteor showers.

  6. Attitude Estimation for Quad-Rotor Aircraft%四旋翼飞行器姿态估计方法

    Institute of Scientific and Technical Information of China (English)

    饶康麒; 刘小明; 陈万春

    2015-01-01

    To the measurement error caused by sensor due to rotor vibration in attitude estimation for quad-rotor aircraft,the data measured by accelerometer and gyroscope are fused through a Kalman filter method,to improve the accuracy of attitude estimation,reduce the noise caused by carrier vibration and solve the gyro drift problem.First,the error types of inertial devices were analyzed,and then a three-DOF ( degree of freedom) system model was established,simulation analysis was also made through Matlab.Finally,the feasibility of this method was verified by using an experimental bench with propellers.Experimental results showed that the attitude estimation error was within 2 °and was not accumulated over time,basically meeting the requirements of attitude estimation for quad-rotor aircraft,such as real-time performance,low cost and high precision.This method could be successfully applied to the attitude control for quad-rotor aircraft,which can suppress the noise interference,and create a good condition for stable autonomous flight.%针对四旋翼飞行器姿态估计中传感器由于旋翼振动带来的测量误差,通过卡尔曼滤波方法融合加速度计和陀螺仪的测量数据来提高姿态估计精度,减少因载体振动带来的噪声并解决陀螺漂移问题。先分析了惯性器件误差类型,然后建立了三自由度的系统模型并用Matlab进行仿真分析,再利用带有螺旋桨的实验台验证方法的可行性。实验结果表明,姿态估计误差在2°以内且没有随时间的增长而增大,基本满足四旋翼飞行器姿态估计的实时性、廉价性、高精度等要求,该方法可以成功应用于四旋翼飞行器的姿态控制,抑制噪声干扰,为稳定的自主飞行创造条件。

  7. Reactor Safety Planning for Prometheus Project, for Naval Reactors Information

    Energy Technology Data Exchange (ETDEWEB)

    P. Delmolino

    2005-05-06

    The purpose of this letter is to submit to Naval Reactors the initial plan for the Prometheus project Reactor Safety work. The Prometheus project is currently developing plans for cold physics experiments and reactor prototype tests. These tests and facilities may require safety analysis and siting support. In addition to the ground facilities, the flight reactor units will require unique analyses to evaluate the risk to the public from normal operations and credible accident conditions. This letter outlines major safety documents that will be submitted with estimated deliverable dates. Included in this planning is the reactor servicing documentation and shipping analysis that will be submitted to Naval Reactors.

  8. REACTOR GROUT THERMAL PROPERTIES

    Energy Technology Data Exchange (ETDEWEB)

    Steimke, J.; Qureshi, Z.; Restivo, M.; Guerrero, H.

    2011-01-28

    Savannah River Site has five dormant nuclear production reactors. Long term disposition will require filling some reactor buildings with grout up to ground level. Portland cement based grout will be used to fill the buildings with the exception of some reactor tanks. Some reactor tanks contain significant quantities of aluminum which could react with Portland cement based grout to form hydrogen. Hydrogen production is a safety concern and gas generation could also compromise the structural integrity of the grout pour. Therefore, it was necessary to develop a non-Portland cement grout to fill reactors that contain significant quantities of aluminum. Grouts generate heat when they set, so the potential exists for large temperature increases in a large pour, which could compromise the integrity of the pour. The primary purpose of the testing reported here was to measure heat of hydration, specific heat, thermal conductivity and density of various reactor grouts under consideration so that these properties could be used to model transient heat transfer for different pouring strategies. A secondary purpose was to make qualitative judgments of grout pourability and hardened strength. Some reactor grout formulations were unacceptable because they generated too much heat, or started setting too fast, or required too long to harden or were too weak. The formulation called 102H had the best combination of characteristics. It is a Calcium Alumino-Sulfate grout that contains Ciment Fondu (calcium aluminate cement), Plaster of Paris (calcium sulfate hemihydrate), sand, Class F fly ash, boric acid and small quantities of additives. This composition afforded about ten hours of working time. Heat release began at 12 hours and was complete by 24 hours. The adiabatic temperature rise was 54 C which was within specification. The final product was hard and displayed no visible segregation. The density and maximum particle size were within specification.

  9. A New Optimal Control Algorithm for Quad-rotor Helicopter with State Constraints via Sliding-mode Control

    Directory of Open Access Journals (Sweden)

    Zhao Jing

    2015-01-01

    Full Text Available This paper proposes a strategy of a new optimal sliding-mode control for flight control system with state constraints so that the system guarantees the optimal performance index. Besides, the strategy ensures strong robustness to the internal parametric uncertainty and the external disturbances. In order to have fast transient response speed as well as good tracking accuracy, the integral of the time multiplied by the absolute displacement tracking error is introduced as the performance index. By analyzing the state constraints which are specifically the velocity tracking error constraint and the acceleration tracking error constraint, and the performance index, the parameters of sliding-mode surface and control law are obtained. Finally, the authors conduct the semi physical simulation on Qball-X4 quad-rotor helicopter, showing the effectiveness of the proposed strategy.

  10. Design and System Analysis of Quad-Generation Plant Based on Biomass Gasification Integrated with District Heating

    DEFF Research Database (Denmark)

    Rudra, Souman

    . Different biomass resources are used to generate heat and electricity, to produce gas fuel like bio-SNG (synthesis natural gas) and also to produce liquid fuels, such as ethanol, and biodiesel. Due to the fact that the trend of establishing new and modern plants for handling and processing biomass......This thesis presents the development of energy system for simulation, techno-economic optimization and design of a quad-generation energy system based on biomass gasification. An efficient way of reducing CO2 emission from the environment is by increasing the use of biomass in the energy sector......, it possible to lay a foundation for future gasification based power sector to produce flexible output such as electricity, heat, chemicals or bio-fuels by improving energy system of existing DHP(district heating plant) integrating gasification technology. The present study investigate energy system...

  11. Multi-Pivot Quicksort: an Experiment with Single, Dual, Triple, Quad, and Penta-Pivot Quicksort Algorithms in Python

    Science.gov (United States)

    Budiman, M. A.; Zamzami, E. M.; Rachmawati, D.

    2017-03-01

    Dual-pivot quicksort, which was proposed by Yaroslavsky, has been experimentally proven to be more efficient than the classical single-pivot quicksort under the Java Virtual Machine [6]. Moreover, Kushagara, López-Ortiz, and Munro [4] has shown that triple-pivot quicksort runs 7-8% faster than dual-pivot quicksort in C, mutatis mutandis. In this research, we implement and experiment with single, dual, triple, quad, and penta-pivot quicksort algorithms in Python. Our experimental results are as follows. Firstly, the quicksort with single pivot is the slowest among the five variants. Secondly, at least until five (penta) pivots are being used, it is proven that the more pivots are used in a quicksort algorithm, the faster its performance becomes. Thirdly, the increase of speed resulted by adding more pivots tends to decrease gradually.

  12. A broadband quad-stable energy harvester and its advantages over bi-stable harvester: Simulation and experiment verification

    Science.gov (United States)

    Zhou, Zhiyong; Qin, Weiyang; Zhu, Pei

    2017-02-01

    This paper presents a novel quad-stable energy harvester (QEH) to harvest vibration energy. The QEH is composed of a piezoelectric bimorph cantilever beam with a tip magnet and three external fixed magnets. The potential energy of the QEH is derived, which has four potential wells and three low barriers. This implies that the QEH needs relatively lower excitation energy to cross the barriers than the bi-stable energy harvester (BEH). Simulations are carried out for the BEH and QEH at different levels of excitations. Results show that the QEH owns a smaller threshold and a wider range of frequencies for occurrence of snap-through than the BEH. Thus the QEH can give out a large output voltage. Corresponding experiments were performed for validation. The experimental results are in agreement with the simulations, which means that the QEH can improve the harvesting efficiency considerably.

  13. Geologic mapping of MTM quads 40292 and 40297: In the Utopian lowlands north of the Nilosyrtis Mensae, Mars

    Science.gov (United States)

    Williams, Steven H.; Zimbelman, James R.

    1991-01-01

    Geologic mapping at 1:500,000 scale of the Mars transverse Mercator (MTM) quads 40292 and 40297 is being conducted under the auspices of the Mars Geologic Mapping Program. The study area is located in the southwestern portion of Utopia Planitia immediately north of the Nilosyrtis Mensae, between latitudes 37.5 and 42.5 degrees and longitudes 290 and 300 degrees. The goals of the mapping are to identify the major geologic features in the study area and to determine the sequence and scope of the geologic events that have modified the lowland side of the global dichotomy boundary in this region in order to at least partially constrain models of dichotomy boundary origin and evolution. The progress made towards achieving these goals is reported.

  14. Scaleable, High Efficiency Microchannel Sabatier Reactor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A Microchannel Sabatier Reactor System (MSRS) consisting of cross connected arrays of isothermal or graded temperature reactors is proposed. The reactor array...

  15. Rice identification at the early stage of the rice growth season with single fine quad Radarsat-2 data

    Science.gov (United States)

    Zhang, Xiaoqian; Zhang, Pengbin; Shen, Kejian; Pei, Zhiyuan

    2016-10-01

    The objective of the study was to determine whether rice identification and acreage estimation accuracy at the early stage of the rice growth season using single fine quad Radarsat-2 images could meet the demand of rice monitoring. The Leizhou site (20°52'N, 110°05'E) is located in Guangdong Province in southern China and is dominated by rice paddies. There was a lack of optical data acquisitions during certain years. There are two rice growth seasons per year. Multitemporal Radarsat-2 products were acquired in the early rice growth season of 2014. First, multi-temporal backscattering coefficients and polarimetric parameters based on H/A/Alpha and Yamaguchi polarimetric decomposition theories were extracted and analyzed to distinguish between rice paddies and other typical land cover types, which could help select the optimal rice growth stage and image characteristics for early season classification. Second, an object-oriented technique was applied to time series backscattering coefficient images (HH, HV, VH, VV), H/A/Alpha images (Entropy, Anistropy and Alpha) and Yamaguchi images (volume, double-bounce, surface and helix). Based on the segmentation images, the supervised Bayes, KNN, SVM and Decision tree classifier were used to identify rice. The results indicated that in flat area, 1) Backscatter images and Yamaguchi images were better than H/A/Alpha images in the rice identification application, and 2) At the early rice growth season, the 0430-Yamaguchi image combined with the objectoriented decision tree algorithm were capable of delivering highly accurate maps of rice (0.9236), while the 0524- backscatter image combined with the object-oriented decision tree algorithm could acquire the highest classification accuracy (0.9278) at the end of the rice growth season. Jointing stage is considered to be appropriate for rice identification at the early season. The study demonstrated that it was possible to identify rice at the early season with single quad C

  16. Cycle Slips Detection in Quad-Frequency Mode: Galileo's Contribution to an Efficient Approach under High Ionospheric Activity

    Science.gov (United States)

    Van de Vyvere, Laura; Warnant, René

    2016-04-01

    Cycle slips detection has always been a key issue in phase measurements accuracy, thus impacting positioning precision. Since Galileo is the first constellation to offer four carrier frequencies available in Open Service, we were able to develop an innovative detection algorithm, especially promising in harsh environment like high ionospheric activity. This improves previous dual and triple-frequency methods, whose efficiency was somehow limited in tricky situations, like ionospheric events or particular configurations. In our algorithm, two types of testing quantities were used: triple-frequency Simsky combination and dual-frequency Geometry-Free combination, each one being associated to a suitable detection algorithm. Simsky combination allows to detect almost every configuration, except for cycle slips of the same magnitude, appearing simultaneously on all carriers. Geometry-Free combination is only used to detect this particular case, since it suffers from quick variation of ionospheric delay. Together - through the choice of the most efficient combination alternatives - they enable the detection of any cycle slips configuration. This is now made possible thanks to the availability of data from Galileo's four carriers. The quad-frequency algorithm has been tested on Galileo observations from both GMSD (Japan) and NKLG (Gabon) stations. On the first ones, cycle slips were artificially inserted in order to simulate particular cases and test algorithm robustness. NKLG raw data were used to assess algorithm behaviour for cases met in the equatorial area. Enhanced with a suitable cycle slip correction method and a real-time feature, our algorithm could directly be integrated into the software receiver, enabling the supply of continuous and corrected data to the user. In conclusion, this first quad-frequency cycle slips detection algorithm is obviously a step forward and every Galileo user will indeed be able to benefit from a highly better-quality positioning. With

  17. LMFBR type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Takeshi; Iida, Masaaki; Moriki, Yasuyuki

    1994-10-18

    A reactor core is divided into a plurality of coolants flowrate regions, and electromagnetic pumps exclusively used for each of the flowrate regions are disposed to distribute coolants flowrates in the reactor core. Further, the flowrate of each of the electromagnetic pumps is automatically controlled depending on signals from a temperature detector disposed at the exit of the reactor core, so that the flowrate of the region can be controlled optimally depending on the burning of reactor core fuels. Then, the electromagnetic pumps disposed for every divided region are controlled respectively, so that the coolants flowrate distribution suitable to each of the regions can be attained. Margin for fuel design is decreased, fuels are used effectively, as well as an operation efficiency can be improved. Moreover, since the electromagnetic pump has less flow resistance compared with a mechanical type pump, and flow resistance of the reactor core flowrate control mechanism is eliminated, greater circulating flowrate can be ensured after occurrence of accident in a natural convection using a buoyancy of coolants utilizable for after-heat removal as a driving force. (N.H.).

  18. Reactor Structural Materials: Reactor Pressure Vessel Steels

    Energy Technology Data Exchange (ETDEWEB)

    Chaouadi, R

    2000-07-01

    The objectives of SCK-CEN's R and D programme on Rector Pressure Vessel (RPV) Steels are:(1) to complete the fracture toughness data bank of various reactor pressure vessel steels by using precracked Charpy specimens that were tested statically as well as dynamically; (2) to implement the enhanced surveillance approach in a user-friendly software; (3) to improve the existing reconstitution technology by reducing the input energy (short cycle welding) and modifying the stud geometry. Progress and achievements in 1999 are reported.

  19. 基于四叉树的动态LOD虚拟地形优化%Optimized Design for Dynamic LOD Virtual Terrain Using Quad Tree

    Institute of Scientific and Technical Information of China (English)

    邹承明; 李引; 陆苑; 陈金锐

    2009-01-01

    In this paper, we present a novel approach of optimized design for dynamic LOD virtual terrain based on quad tree. In the process of building quad tree which on the basis of multi-resolution terrain model, we firstly optimize the quad tree of a mesh respectively according to the three criteria of the quad tree, that is bounding volume omitting, face culling and projection error analysis, Then we set up a suitable node evaluation function, according to the different degrees of details to show the viewpoint moves when we are roaming the LOD terrain. To remove the unreasonable quad tree partition, we put forward an appropriate cracks elimination based on the law of segmentation and rendering in the process of LOD mode simplification. Finally after the partition of the nodes optimally, we achieve the goal of optimizing the quad tree mesh.%提出了一种基于四叉树的动态LOD优化方法.基于多分辨率地形模型的四叉树构建过程,首先针对四叉树优化采用的3个判断标准--包围体剔除、背面剔除和屏幕投影误差分别进行相应的网格优化,然后在LOD地形中漫游时,随着视点移动而呈现出的不同细节程度的需要,建立了合适的节点评价函数,并在LOD简化过程中根据节点分割和渲染的规律,提出合适的裂缝消除算法,去掉四叉树中不合理的分割,最后使得分割后的节点达到最优以完成四叉树网格优化的目的.

  20. Operation of Reactor

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    3.1 Annual Report of SPR Operation Chu Shaochu Having overseen by National Nuclear Safety Administration and specialists, the reactor restarted up successfully after Safety renovation on April 16, 1996. In August 1996 the normal operation of SPR was approved by the authorities of Naitonal Nuclear Safety Administration. 1 Operation status In 1996, the reactor operated safely for 40 d and the energy released was about 137.3 MW·d. The operation status of SPR is shown in table 1. The reactor started up to higher power (power more than 1 MW) and lower power (for physics experiments) 4 times and 14 times respectively. Measurement of control rod efficiency and other measurement tasks were 2 times and 5 times respectively.

  1. Nuclear Rocket Engine Reactor

    CERN Document Server

    Lanin, Anatoly

    2013-01-01

    The development of a nuclear rocket engine reactor (NRER ) is presented in this book. The working capacity of an active zone NRER under mechanical and thermal load, intensive neutron fluxes, high energy generation (up to 30 MBT/l) in a working medium (hydrogen) at temperatures up to 3100 K is displayed. Design principles and bearing capacity of reactors area discussed on the basis of simulation experiments and test data of a prototype reactor. Property data of dense constructional, porous thermal insulating and fuel materials like carbide and uranium carbide compounds in the temperatures interval 300 - 3000 K are presented. Technological aspects of strength and thermal strength resistance of materials are considered. The design procedure of possible emergency processes in the NRER is developed and risks for their origination are evaluated. Prospects of the NRER development for pilotless space devices and piloted interplanetary ships are viewed.

  2. Thermionic Reactor Design Studies

    Energy Technology Data Exchange (ETDEWEB)

    Schock, Alfred

    1994-08-01

    Paper presented at the 29th IECEC in Monterey, CA in August 1994. The present paper describes some of the author's conceptual designs and their rationale, and the special analytical techniques developed to analyze their (thermionic reactor) performance. The basic designs, first published in 1963, are based on single-cell converters, either double-ended diodes extending over the full height of the reactor core or single-ended diodes extending over half the core height. In that respect they are similar to the thermionic fuel elements employed in the Topaz-2 reactor subsequently developed in the Soviet Union, copies of which were recently imported by the U.S. As in the Topaz-2 case, electrically heated steady-state performance tests of the converters are possible before fueling.

  3. An Overview of Reactor Concepts, a Survey of Reactor Designs.

    Science.gov (United States)

    1985-02-01

    Public Affairs Office and is releasaole to the National Technical Information Services (NTIS). At NTIS, it will be available to the general public...Reactors that use deu- terium (heavy water) as a coolant can use natural uranium as a fuel. The * Canadian reactor, CANDU , utilizes this concept...reactor core at the top and discharged at the Dotton while the reactor is in operation. The discharged fuel can then b inspected to see if it can De used

  4. Oscillatory flow chemical reactors

    Directory of Open Access Journals (Sweden)

    Slavnić Danijela S.

    2014-01-01

    Full Text Available Global market competition, increase in energy and other production costs, demands for high quality products and reduction of waste are forcing pharmaceutical, fine chemicals and biochemical industries, to search for radical solutions. One of the most effective ways to improve the overall production (cost reduction and better control of reactions is a transition from batch to continuous processes. However, the reactions of interests for the mentioned industry sectors are often slow, thus continuous tubular reactors would be impractically long for flow regimes which provide sufficient heat and mass transfer and narrow residence time distribution. The oscillatory flow reactors (OFR are newer type of tube reactors which can offer solution by providing continuous operation with approximately plug flow pattern, low shear stress rates and enhanced mass and heat transfer. These benefits are the result of very good mixing in OFR achieved by vortex generation. OFR consists of cylindrical tube containing equally spaced orifice baffles. Fluid oscillations are superimposed on a net (laminar flow. Eddies are generated when oscillating fluid collides with baffles and passes through orifices. Generation and propagation of vortices create uniform mixing in each reactor cavity (between baffles, providing an overall flow pattern which is close to plug flow. Oscillations can be created by direct action of a piston or a diaphragm on fluid (or alternatively on baffles. This article provides an overview of oscillatory flow reactor technology, its operating principles and basic design and scale - up characteristics. Further, the article reviews the key research findings in heat and mass transfer, shear stress, residence time distribution in OFR, presenting their advantages over the conventional reactors. Finally, relevant process intensification examples from pharmaceutical, polymer and biofuels industries are presented.

  5. Perspectives on reactor safety

    Energy Technology Data Exchange (ETDEWEB)

    Haskin, F.E. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Chemical and Nuclear Engineering; Camp, A.L. [Sandia National Labs., Albuquerque, NM (United States)

    1994-03-01

    The US Nuclear Regulatory Commission (NRC) maintains a technical training center at Chattanooga, Tennessee to provide appropriate training to both new and experienced NRC employees. This document describes a one-week course in reactor, safety concepts. The course consists of five modules: (1) historical perspective; (2) accident sequences; (3) accident progression in the reactor vessel; (4) containment characteristics and design bases; and (5) source terms and offsite consequences. The course text is accompanied by slides and videos during the actual presentation of the course.

  6. Reactor Materials Research

    Energy Technology Data Exchange (ETDEWEB)

    Van Walle, E

    2002-04-01

    The activities of SCK-CEN's Reactor Materials Research Department for 2001 are summarised. The objectives of the department are: (1) to evaluate the integrity and behaviour of structural materials used in nuclear power industry; (2) to conduct research to unravel and understand the parameters that determine the material behaviour under or after irradiation; (3) to contribute to the interpretation, the modelling of the material behaviour and to develop and assess strategies for optimum life management of nuclear power plant components. The programmes within the department are focussed on studies concerning (1) Irradiation Assisted Stress Corrosion Cracking (IASCC); (2) nuclear fuel; and (3) Reactor Pressure Vessel Steel.

  7. Fusion Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2000-07-01

    SCK-CEN's research and development programme on fusion reactor materials includes: (1) the study of the mechanical behaviour of structural materials under neutron irradiation (including steels, inconel, molybdenum, chromium); (2) the determination and modelling of the characteristics of irradiated first wall materials such as beryllium; (3) the detection of abrupt electrical degradation of insulating ceramics under high temperature and neutron irradiation; (4) the study of the dismantling and waste disposal strategy for fusion reactors.; (5) a feasibility study for the testing of blanket modules under neutron radiation. Main achievements in these topical areas in the year 1999 are summarised.

  8. High Flux Isotope Reactor (HFIR)

    Data.gov (United States)

    Federal Laboratory Consortium — The HFIR at Oak Ridge National Laboratory is a light-water cooled and moderated reactor that is the United States’ highest flux reactor-based neutron source. HFIR...

  9. Reactor operation environmental information document

    Energy Technology Data Exchange (ETDEWEB)

    Haselow, J.S.; Price, V.; Stephenson, D.E.; Bledsoe, H.W.; Looney, B.B.

    1989-12-01

    The Savannah River Site (SRS) produces nuclear materials, primarily plutonium and tritium, to meet the requirements of the Department of Defense. These products have been formed in nuclear reactors that were built during 1950--1955 at the SRS. K, L, and P reactors are three of five reactors that have been used in the past to produce the nuclear materials. All three of these reactors discontinued operation in 1988. Currently, intense efforts are being extended to prepare these three reactors for restart in a manner that protects human health and the environment. To document that restarting the reactors will have minimal impacts to human health and the environment, a three-volume Reactor Operations Environmental Impact Document has been prepared. The document focuses on the impacts of restarting the K, L, and P reactors on both the SRS and surrounding areas. This volume discusses the geology, seismology, and subsurface hydrology. 195 refs., 101 figs., 16 tabs.

  10. Reactor operation safety information document

    Energy Technology Data Exchange (ETDEWEB)

    1990-01-01

    The report contains a reactor facility description which includes K, P, and L reactor sites, structures, operating systems, engineered safety systems, support systems, and process and effluent monitoring systems; an accident analysis section which includes cooling system anomalies, radioactive materials releases, and anticipated transients without scram; a summary of onsite doses from design basis accidents; severe accident analysis (reactor core disruption); a description of operating contractor organization and emergency planning; and a summary of reactor safety evolution. (MB)

  11. REACTOR FUEL ELEMENTS TESTING CONTAINER

    Science.gov (United States)

    Whitham, G.K.; Smith, R.R.

    1963-01-15

    This patent shows a method for detecting leaks in jacketed fuel elements. The element is placed in a sealed tank within a nuclear reactor, and, while the reactor operates, the element is sparged with gas. The gas is then led outside the reactor and monitored for radioactive Xe or Kr. (AEC)

  12. Nuclear Reactors and Technology

    Energy Technology Data Exchange (ETDEWEB)

    Cason, D.L.; Hicks, S.C. [eds.

    1992-01-01

    This publication Nuclear Reactors and Technology (NRT) announces on a monthly basis the current worldwide information available from the open literature on nuclear reactors and technology, including all aspects of power reactors, components and accessories, fuel elements, control systems, and materials. This publication contains the abstracts of DOE reports, journal articles, conference papers, patents, theses, and monographs added to the Energy Science and Technology Database during the past month. Also included are US information obtained through acquisition programs or interagency agreements and international information obtained through the International Energy Agency`s Energy Technology Data Exchange or government-to-government agreements. The digests in NRT and other citations to information on nuclear reactors back to 1948 are available for online searching and retrieval on the Energy Science and Technology Database and Nuclear Science Abstracts (NSA) database. Current information, added daily to the Energy Science and Technology Database, is available to DOE and its contractors through the DOE Integrated Technical Information System. Customized profiles can be developed to provide current information to meet each user`s needs.

  13. WATER BOILER REACTOR

    Science.gov (United States)

    King, L.D.P.

    1960-11-22

    As its name implies, this reactor utilizes an aqueous solution of a fissionable element salt, and is also conventional in that it contains a heat exchanger cooling coil immersed in the fuel. Its novelty lies in the utilization of a cylindrical reactor vessel to provide a critical region having a large and constant interface with a supernatant vapor region, and the use of a hollow sleeve coolant member suspended from the cover assembly in coaxial relation with the reactor vessel. Cool water is circulated inside this hollow coolant member, and a gap between its outer wall and the reactor vessel is used to carry off radiolytic gases for recombination in an external catalyst chamber. The central passage of the coolant member defines a reflux condenser passage into which the externally recombined gases are returned and condensed. The large and constant interface between fuel solution and vapor region prevents the formation of large bubbles and minimizes the amount of fuel salt carried off by water vapor, thus making possible higher flux densities, specific powers and power densities.

  14. MULTISTAGE FLUIDIZED BED REACTOR

    Science.gov (United States)

    Jonke, A.A.; Graae, J.E.A.; Levitz, N.M.

    1959-11-01

    A multistage fluidized bed reactor is described in which each of a number of stages is arranged with respect to an associated baffle so that a fluidizing gas flows upward and a granular solid downward through the stages and baffles, whereas the granular solid stopsflowing downward when the flow of fluidizing gas is shut off.

  15. Fusion reactor materials

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1989-01-01

    This paper discuses the following topics on fusion reactor materials: irradiation, facilities, test matrices, and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; fundamental mechanical behavior; radiation effects; development of structural alloys; solid breeding materials; and ceramics.

  16. Integral Fast Reactor concept

    Energy Technology Data Exchange (ETDEWEB)

    Till, C.E.; Chang, Y.I.

    1986-01-01

    The Integral Fast Reactor (IFR) is an innovative LMR concept, being developed at Argonne National Laboratory, that fully exploits the inherent properties of liquid metal cooling and metallic fuel to achieve breakthroughs in economics and inherent safety. This paper describes key features and potential advantages of the IFR concept, technology development status, fuel cycle economics potential, and future development path.

  17. The First Reactor.

    Science.gov (United States)

    Department of Energy, Washington, DC.

    On December 2, 1942, in a racquet court underneath the West Stands of Stagg Field at the University of Chicago, a team of scientists led by Enrico Fermi created the first controlled, self-sustaining nuclear chain reaction. This updated and revised story of the first reactor (or "pile") is based on postwar interviews (as told to Corbin…

  18. Thermal Reactor Safety

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Information is presented concerning fire risk and protection; transient thermal-hydraulic analysis and experiments; class 9 accidents and containment; diagnostics and in-service inspection; risk and cost comparison of alternative electric energy sources; fuel behavior and experiments on core cooling in LOCAs; reactor event reporting analysis; equipment qualification; post facts analysis of the TMI-2 accident; and computational methods.

  19. Chromatographic and Related Reactors.

    Science.gov (United States)

    1988-01-07

    special information about effects of surface heteroge- neity in the methanation reaction. Studies of an efficient multicolumn assembly for measuring...of organic basic catalysts such as pyridine and 4-methylpicoline. It was demonstrated that the chromatographic reactor gave special information about...Programmed Reaction to obtain special information about surface heterogeneity in the methanation reaction. Advantages of stopped flow over steady state

  20. New concepts for shaftless recycle reactors

    Energy Technology Data Exchange (ETDEWEB)

    Berty, J.M.; Berty, I.J.

    1987-01-01

    Berty Reaction Engineers, Ltd. (BREL) is developing two new laboratory recycle reactors, the ROTOBERTY and the TURBOBERTY. These new reactors are basically improved versions of the original Berty reactor. To understand why the reactors have the features that they do, it is first necessary to briefly review laboratory reactors in general and specifically the original Berty reactor.

  1. Brazilian multipurpose reactor

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-07-01

    The Brazilian Multipurpose Reactor (RMB) Project is an action of the Federal Government, through the Ministry of Science Technology and Innovation (MCTI) and has its execution under the responsibility of the Brazilian National Nuclear Energy Commission (CNEN). Within the CNEN, the project is coordinated by the Research and Development Directorate (DPD) and developed through research units of this board: Institute of Nuclear Energy Research (IPEN); Nuclear Engineering Institute (IEN); Centre for Development of Nuclear Technology (CDTN); Regional Center of Nuclear Sciences (CRCN-NE); and Institute of Radiation Protection and Dosimetry (IRD). The Navy Technological Center in Sao Paulo (CTMSP) and also the participation of other research centers, universities, laboratories and companies in the nuclear sector are important and strategic partnerships. The conceptual design and the safety analysis of the reactor and main facilities, related to nuclear and environmental licensing, are performed by technicians of the research units of DPD / CNEN. The basic design was contracted to engineering companies as INTERTHECNE from Brazil and INVAP from Argentine. The research units from DPD/CNEN are also responsible for the design verification on all engineering documents developed by the contracted companies. The construction and installation should be performed by specific national companies and international partnerships. The Nuclear Reactor RMB will be a open pool type reactor with maximum power of 30 MW and have the OPAL nuclear reactor of 20 MW, built in Australia and designed by INVAP, as reference. The RMB reactor core will have a 5x5 configuration, consisting of 23 elements fuels (EC) of U{sub 3}Si{sub 2} dispersion-type Al having a density of up to 3.5 gU/cm{sup 3} and enrichment of 19.75% by weight of {sup 23{sup 5}}U. Two positions will be available in the core for materials irradiation devices. The main objectives of the RMB Reactor and the other nuclear and radioactive

  2. Positive Peer-Pressured Productivity (P-QUAD): Novel Use of Increased Transparency and a Weighted Lottery to Increase a Division's Academic Output.

    Science.gov (United States)

    Pitt, Michael B; Furnival, Ronald A; Zhang, Lei; Weber-Main, Anne M; Raymond, Nancy C; Jacob, Abraham K

    2017-03-01

    Evaluate a dual incentive model combining positive peer pressure through increased transparency of peers' academic work with a weighted lottery where entries are earned based on degree of productivity. We developed a dual-incentive peer mentoring model, Positive Peer-Pressured Productivity (P-QUAD), for faculty in the Pediatric Hospital Medicine Division at the University of Minnesota Masonic Children's Hospital. This model provided relative value-based incentives, with points assigned to different scholarly activities (eg. 1 point for abstract submission, 2 points for poster presentation, 3 points for oral presentation, etc.). These points translated into to lottery tickets for a semi-annual drawing for monetary prizes. Productivity was compared among faculty for P-QUAD year to the preintervention year. Fifteen (83%) of 18 eligible faculty members participated. Overall annual productivity per faculty member as measured by total P-QUAD score increased from a median of 3 (interquartile range [IQR] 0-14) in the preintervention year to 4 (IQR 0-27) in the P-QUAD year (P = .051). Submissions and acceptances increased in all categories except posters which were unchanged. Annual abstract submissions per faculty member significantly increased from a median of 1 (IQR 0-2) to 2 (IQR 0-2; P = .047). Seventy-three percent (8 of 11) of post-survey respondents indicated that the financial incentive motivated them to submit academic work; 100% indicated that increased awareness of their peers' work was a motivator. The combination of increased awareness of peers' academic productivity and a weighted lottery financial incentive appears to be a useful model for stimulating academic productivity in early-career faculty. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

  3. Modeling Chemical Reactors I: Quiescent Reactors

    CERN Document Server

    Michoski, C E; Schmitz, P G

    2010-01-01

    We introduce a fully generalized quiescent chemical reactor system in arbitrary space $\\vdim =1,2$ or 3, with $n\\in\\mathbb{N}$ chemical constituents $\\alpha_{i}$, where the character of the numerical solution is strongly determined by the relative scaling between the local reactivity of species $\\alpha_{i}$ and the local functional diffusivity $\\mathscr{D}_{ij}(\\alpha)$ of the reaction mixture. We develop an operator time-splitting predictor multi-corrector RK--LDG scheme, and utilize $hp$-adaptivity relying only on the entropy $\\mathscr{S}_{\\mathfrak{R}}$ of the reactive system $\\mathfrak{R}$. This condition preserves these bounded nonlinear entropy functionals as a necessarily enforced stability condition on the coupled system. We apply this scheme to a number of application problems in chemical kinetics; including a difficult classical problem arising in nonequilibrium thermodynamics known as the Belousov-Zhabotinskii reaction where we utilize a concentration-dependent diffusivity tensor $\\mathscr{D}_{ij}(...

  4. Alternative approaches to fusion. [reactor design and reactor physics for Tokamak fusion reactors

    Science.gov (United States)

    Roth, R. J.

    1976-01-01

    The limitations of the Tokamak fusion reactor concept are discussed and various other fusion reactor concepts are considered that employ the containment of thermonuclear plasmas by magnetic fields (i.e., stellarators). Progress made in the containment of plasmas in toroidal devices is reported. Reactor design concepts are illustrated. The possibility of using fusion reactors as a power source in interplanetary space travel and electric power plants is briefly examined.

  5. 可伸缩折叠式四旋翼飞行器设计%Design for the Scalable Folding Quad Rotor Aircraft

    Institute of Scientific and Technical Information of China (English)

    李波陈; 王红州; 刘晓栋; 徐兴国; 李彦锐

    2015-01-01

    The optimization design for quad rotor aircraft is completed in this article for its structural shape is awkward to car-ry.Through analyzing the structure characteristics and flight principles, a quad rotor aircraft platform that could automatically retract and fold is designed, and its strength is then checked, and finally 3D modeling simulation and experimental tests are conducted.The result shows that design of the quad rotor aircraft successfully achieves automatic retractable and manual fold-ing, and meanwhile could save the carrying space, thus it gets good effects.%针对四旋翼飞行器的结构外形不便于随身携带的特点,进行了优化设计。通过分析四旋翼飞行器结构特点和飞行原理,设计出可自动伸缩、折叠的四旋翼飞行器平台,并进行强度校核,最后进行了三维仿真建模与模型制作和试验测试。结果表明设计的四旋翼无人飞行器实现了空中自动伸缩、着陆后手动折叠的功能,同时节省携带空间,达到了良好的效果。

  6. Unrealistic optimism, fatalism, and risk-taking in New Zealand farmers' descriptions of quad-bike incidents: a directed qualitative content analysis.

    Science.gov (United States)

    Clay, Lynne; Hay-Smith, E Jean C; Treharne, Gareth J; Milosavljevic, Stephan

    2015-01-01

    Quad-bike incidents are a major cause of occupational injury and fatality on farms warranting health and safety attention. As part of a larger study, we carried out a face-to-face survey with 216 farmers in New Zealand. We quantitatively identified farmers' propensity for risk-taking, unrealistic optimism, and fatalism as risk factors in quad-bike loss-of-control events (LCEs). The purpose of the analysis presented in this article was to use these same farmers' recollections of LCEs to explore the a priori constructs in more detail using qualitative methods. Participants reporting one or more LCEs described their first LCE and any experienced in the previous 12 months. Participants provided open-text responses about what occurred at each LCE, their reflections, and general thoughts on LCE risk factors. Directed qualitative content analysis (QCA) was used to "unpack" risk-taking, unrealistic optimism, and fatalism whilst also delineating any additional concepts that farmers associate with LCEs. Risk-taking elements were more evident than unrealistic optimism or fatalism and more suggestive of farmers finding themselves in risky situations rather than engaging in risk-seeking behavior per se. Additional inductively derived categories of fatigue/stress, multitasking, inexperience, and quad-bike faults highlight the complex nature of LCEs and the importance of risk assessment covering these concepts as well as risky situations.

  7. Reactor monitoring using antineutrino detectors

    Science.gov (United States)

    Bowden, N. S.

    2011-08-01

    Nuclear reactors have served as the antineutrino source for many fundamental physics experiments. The techniques developed by these experiments make it possible to use these weakly interacting particles for a practical purpose. The large flux of antineutrinos that leaves a reactor carries information about two quantities of interest for safeguards: the reactor power and fissile inventory. Measurements made with antineutrino detectors could therefore offer an alternative means for verifying the power history and fissile inventory of a reactor as part of International Atomic Energy Agency (IAEA) and/or other reactor safeguards regimes. Several efforts to develop this monitoring technique are underway worldwide.

  8. Reactor vessel support system. [LMFBR

    Science.gov (United States)

    Golden, M.P.; Holley, J.C.

    1980-05-09

    A reactor vessel support system includes a support ring at the reactor top supported through a box ring on a ledge of the reactor containment. The box ring includes an annular space in the center of its cross-section to reduce heat flow and is keyed to the support ledge to transmit seismic forces from the reactor vessel to the containment structure. A coolant channel is provided at the outside circumference of the support ring to supply coolant gas through the keyways to channels between the reactor vessel and support ledge into the containment space.

  9. Probabilistic Assessment of Soil Moisture using C-band Quad-polarized Remote Sensing Data from RISAT1

    Science.gov (United States)

    Pal, Manali; Suman, Mayank; Das, Sarit Kumar; Maity, Rajib

    2017-04-01

    Information on spatio-temporal distribution of surface Soil Moisture Content (SMC) is essential in several hydrological, meteorological and agricultural applications. There has been increasing importance of microwave active remote sensing data for large-scale estimation of surface SMC because of its ability to monitor spatial and temporal variation of surface SMC at regional, continental and global scale at a reasonably fine spatial and temporal resolution. The use of Synthetic Aperture Radar (SAR) is highly potential for catchment-scale applications due to high spatial resolution (˜10-20 m) both for vegetated and bare soil surface as well as because of its all-weather and day and night characteristics. However, one prime disadvantage of SAR is that their signal is subjective to SMC along with Land Use Land Cover (LULC) and surface roughness conditions, making the retrieval of SMC from SAR data an "ill-posed" problem. Moreover, the quantification of uncertainty due to inappropriate surface roughness characterization, soil texture, inversion techniques etc. even in the latest established retrieval methods, is little explored. This paper reports a recently developed method to estimate the surface SMC with probabilistic assessment of uncertainty associated with the estimation (Pal et al., 2016). Quad-polarized SAR data from Radar Imaging Satellite1 (RISAT1), launched in 2012 by Indian Space Research Organization (ISRO) and information on LULC regarding bareland and vegetated land (<30 cm height) are used in estimation using the potential of multivariate probabilistic assessment through copulas. The salient features of the study are: 1) development of a combined index to understand the role of all the quad-polarized backscattering coefficients and soil texture information in SMC estimation; 2) applicability of the model for different incidence angles using normalized incidence angle theory proposed by Zibri et al. (2005); and 3) assessment of uncertainty range of the

  10. Methanogenesis in Thermophilic Biogas Reactors

    DEFF Research Database (Denmark)

    Ahring, Birgitte Kiær

    1995-01-01

    Methanogenesis in thermophilic biogas reactors fed with different wastes is examined. The specific methanogenic activity with acetate or hydrogen as substrate reflected the organic loading of the specific reactor examined. Increasing the loading of thermophilic reactors stabilized the process...... as indicated by a lower concentration of volatile fatty acids in the effluent from the reactors. The specific methanogenic activity in a thermophilic pilot-plant biogas reactor fed with a mixture of cow and pig manure reflected the stability of the reactor. The numbers of methanogens counted by the most...... against Methanothrix soehngenii or Methanothrix CALS-I in any of the thermophilic biogas reactors examined. Studies using 2-14C-labeled acetate showed that at high concentrations (more than approx. 1 mM) acetate was metabolized via the aceticlastic pathway, transforming the methyl-group of acetate...

  11. Four-quad multilevel converter%一种新型四象限多电平变流器

    Institute of Scientific and Technical Information of China (English)

    高志刚; 冬雷; 廖晓钟; 庄亚平; 周德佳

    2013-01-01

    A four-quad multilevel converter topology is proposed,which is composed of H-bridge rectifier,middle-frequency transformer and cascaded H-bridge inverter.The power flow model of converter is established,and its control algorithm and modulation strategy are presented.The output voltage model of input-side converter is analyzed and the corresponding modulation strategy is proposed.The working phase of each middle-frequency H-bridge is described,which functions to keep the voltage balance for each capacitor and realize the four-quad operation of converter.The experimental result validates the correctness of the proposed topology and algorithm.Without the power frequency transformer,the proposed converter has small size and weight,and is applicable in high-voltage large-capacity condition.%提出了一种新型四象限多电平变流器拓扑结构,由级联H桥型整流器、中频变压器和级联H桥型逆变器三部分构成.建立了变流器的能量传输模型,提出了相应的控制方法和调制策略;分析了输入侧变换器的输出电压模型,给出了相应的调制算法流程.阐述了各中频H桥的工作相位的作用,即达到了控制各电容电压平衡的目的,实现了变流器的四象限运行.实验结果验证了拓扑结构和控制方法的正确性.所提变流器拓扑结构省去了传统的工频变压器,降低了变换器体积和重量,可以应用于高压大容量场合.

  12. On the Added Value of Quad-Pol Data in a Multi-Temporal Crop Classification Framework Based on RADARSAT-2 Imagery

    Directory of Open Access Journals (Sweden)

    Arantzazu Larrañaga

    2016-04-01

    Full Text Available Polarimetric SAR images are a rich data source for crop mapping. However, quad-pol sensors have some limitations due to their complexity, increased data rate, and reduced coverage and revisit time. The main objective of this study was to evaluate the added value of quad-pol data in a multi-temporal crop classification framework based on SAR imagery. With this aim, three RADARSAT-2 scenes were acquired between May and June 2010. Once we analyzed the separability and the descriptive analysis of the features, an object-based supervised classification was performed using the Random Forests classification algorithm. Classification results obtained with dual-pol (VV-VH data as input were compared to those using quad-pol data in different polarization bases (linear H-V, circular, and linear 45°, and also to configurations where several polarimetric features (Pauli and Cloude–Pottier decomposition features and co-pol coherence and phase difference were added. Dual-pol data obtained satisfactory results, equal to those obtained with quad-pol data (in H-V basis in terms of overall accuracy (0.79 and Kappa values (0.69. Quad-pol data in circular and linear 45° bases resulted in lower accuracies. The inclusion of polarimetric features, particularly co-pol coherence and phase difference, resulted in enhanced classification accuracies with an overall accuracy of 0.86 and Kappa of 0.79 in the best case, when all the polarimetric features were added. Improvements were also observed in the identification of some particular crops, but major crops like cereals, rapeseed, and sunflower already achieved a satisfactory accuracy with the VV-VH dual-pol configuration and obtained only minor improvements. Therefore, it can be concluded that C-band VV-VH dual-pol data is almost ready to be used operationally for crop mapping as long as at least three acquisitions in dates reflecting key growth stages representing typical phenology differences of the present crops are

  13. Compact fusion reactors

    CERN Document Server

    CERN. Geneva

    2015-01-01

    Fusion research is currently to a large extent focused on tokamak (ITER) and inertial confinement (NIF) research. In addition to these large international or national efforts there are private companies performing fusion research using much smaller devices than ITER or NIF. The attempt to achieve fusion energy production through relatively small and compact devices compared to tokamaks decreases the costs and building time of the reactors and this has allowed some private companies to enter the field, like EMC2, General Fusion, Helion Energy, Lawrenceville Plasma Physics and Lockheed Martin. Some of these companies are trying to demonstrate net energy production within the next few years. If they are successful their next step is to attempt to commercialize their technology. In this presentation an overview of compact fusion reactor concepts is given.

  14. MEANS FOR COOLING REACTORS

    Science.gov (United States)

    Wheeler, J.A.

    1957-11-01

    A design of a reactor is presented in which the fuel elements may be immersed in a liquid coolant when desired without the necessity of removing them from the reactor structure. The fuel elements, containing the fissionable material are in plate form and are disposed within spaced slots in a moderator material, such as graphite to form the core. Adjacent the core is a tank containing the liquid coolant. The fuel elements are mounted in spaced relationship on a rotatable shaft which is located between the core and the tank so that by rotation of the shaft the fuel elements may be either inserted in the slots in the core to sustain a chain reaction or immersed in the coolant.

  15. Integrated Microfluidic Reactors.

    Science.gov (United States)

    Lin, Wei-Yu; Wang, Yanju; Wang, Shutao; Tseng, Hsian-Rong

    2009-12-01

    Microfluidic reactors exhibit intrinsic advantages of reduced chemical consumption, safety, high surface-area-to-volume ratios, and improved control over mass and heat transfer superior to the macroscopic reaction setting. In contract to a continuous-flow microfluidic system composed of only a microchannel network, an integrated microfluidic system represents a scalable integration of a microchannel network with functional microfluidic modules, thus enabling the execution and automation of complicated chemical reactions in a single device. In this review, we summarize recent progresses on the development of integrated microfluidics-based chemical reactors for (i) parallel screening of in situ click chemistry libraries, (ii) multistep synthesis of radiolabeled imaging probes for positron emission tomography (PET), (iii) sequential preparation of individually addressable conducting polymer nanowire (CPNW), and (iv) solid-phase synthesis of DNA oligonucleotides. These proof-of-principle demonstrations validate the feasibility and set a solid foundation for exploring a broad application of the integrated microfluidic system.

  16. Reactor Neutrino Spectra

    OpenAIRE

    Hayes, A. C.; Vogel, Petr

    2016-01-01

    We present a review of the antineutrino spectra emitted from reactors. Knowledge of these spectra and their associated uncertainties is crucial for neutrino oscillation studies. The spectra used to date have been determined either by converting measured electron spectra to antineutrino spectra or by summing over all of the thousands of transitions that make up the spectra, using modern databases as input. The uncertainties in the subdominant corrections to β-decay plague both methods, and we ...

  17. REACTOR MODERATOR STRUCTURE

    Science.gov (United States)

    Greenstreet, B.L.

    1963-12-31

    A system for maintaining the alignment of moderator block structures in reactors is presented. Integral restraining grids are placed between each layer of blocks in the moderator structure, at the top of the uppermost layer, and at the bottom of the lowermost layer. Slots are provided in the top and bottom surfaces of the moderator blocks so as to provide a keying action with the grids. The grids are maintained in alignment by vertical guiding members disposed about their peripheries. (AEC)

  18. BOILER-SUPERHEATED REACTOR

    Science.gov (United States)

    Heckman, T.P.

    1961-05-01

    A nuclear power reactor of the type in which a liquid moderator-coolant is transformed by nuclear heating into a vapor that may be used to drive a turbo- generator is described. The core of this reactor comprises a plurality of freely suspended tubular fuel elements, called fuel element trains, within which nonboiling pressurized liquid moderator-coolant is preheated and sprayed through orifices in the walls of the trains against the outer walls thereof to be converted into vapor. Passage of the vapor ovcr other unwetted portions of the outside of the fuel elements causes the steam to be superheated. The moderatorcoolant within the fuel elements remains in the liqUid state, and that between the fuel elements remains substantiaily in the vapor state. A unique liquid neutron-absorber control system is used. Advantages expected from the reactor design include reduced fuel element failure, increased stability of operation, direct response to power demand, and circulation of a minimum amount of liquid moderatorcoolant. (A.G.W.)

  19. The OPAL reactor

    Energy Technology Data Exchange (ETDEWEB)

    Miller, R.; Irwin, T. [Australian Nuclear Science and Technology Organisation, Sydney (Australia); Ordonez, J.P. [INVAP SE, Bariloche (Argentina)

    2007-07-01

    The project to provide a replacement for Australia's HIFAR reactor began with governmental approval in September 1997 and reached its latest milestone with the achievement of the first full power operation of the OPAL reactor in November 2006. OPAL is a pool-type reactor with a thermal power of 20 MW and a fuel enrichment maximum of 20 per cent. This has been a successful project for both ANSTO (Australian Nuclear Science and Technology Organisation) and the contractor INVAP SE. This project was characterised by extensive interaction with the project's stake-holders during project definition and the use of a performance-based turnkey contract which gave the contractor the maximum opportunity to optimise the design to achieve performance and cost effectiveness. The contactor provided significant in-house resources as well as capacity to manage an international team of suppliers and sub-contractors. A key contributor to the project's successful outcomes has been the development and maintenance of an excellent working relationship between ANSTO and INVAP project teams. Commissioning was undertaken in accordance with the IAEA recommended stages. This paper presents the approaches used to define the project requirements, to choose the supplier and to deliver the project. The main results of hot commissioning are reviewed and the problems encountered examined. Operational experience since hot commissioning is also reviewed.

  20. Nuclear research reactors in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Cota, Anna Paula Leite; Mesquita, Amir Zacarias, E-mail: aplc@cdtn.b, E-mail: amir@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    The rising concerns about global warming and energy security have spurred a revival of interest in nuclear energy, giving birth to a 'nuclear power renaissance' in several countries in the world. Particularly in Brazil, in the recent years, the nuclear power renaissance can be seen in the actions that comprise its nuclear program, summarily the increase of the investments in nuclear research institutes and the government target to design and build the Brazilian Multipurpose research Reactor (BMR). In the last 50 years, Brazilian research reactors have been used for training, for producing radioisotopes to meet demands in industry and nuclear medicine, for miscellaneous irradiation services and for academic research. Moreover, the research reactors are used as laboratories to develop technologies in power reactors, which are evaluated today at around 450 worldwide. In this application, those reactors become more viable in relation to power reactors by the lowest cost, by the operation at low temperatures and, furthermore, by lower demand for nuclear fuel. In Brazil, four research reactors were installed: the IEA-R1 and the MB-01 reactors, both at the Instituto de Pesquisas Energeticas Nucleares (IPEN, Sao Paulo); the Argonauta, at the Instituto de Engenharia Nuclear (IEN, Rio de Janeiro) and the IPR-R1 TRIGA reactor, at the Centro de Desenvolvimento da Tecnologia Nuclear (CDTN, Belo Horizonte). The present paper intends to enumerate the characteristics of these reactors, their utilization and current academic research. Therefore, through this paper, we intend to collaborate on the BMR project. (author)

  1. Nuclear research reactors in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Cota, Anna Paula Leite; Mesquita, Amir Zacarias, E-mail: aplc@cdtn.b, E-mail: amir@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    The rising concerns about global warming and energy security have spurred a revival of interest in nuclear energy, giving birth to a 'nuclear power renaissance' in several countries in the world. Particularly in Brazil, in the recent years, the nuclear power renaissance can be seen in the actions that comprise its nuclear program, summarily the increase of the investments in nuclear research institutes and the government target to design and build the Brazilian Multipurpose research Reactor (BMR). In the last 50 years, Brazilian research reactors have been used for training, for producing radioisotopes to meet demands in industry and nuclear medicine, for miscellaneous irradiation services and for academic research. Moreover, the research reactors are used as laboratories to develop technologies in power reactors, which are evaluated today at around 450 worldwide. In this application, those reactors become more viable in relation to power reactors by the lowest cost, by the operation at low temperatures and, furthermore, by lower demand for nuclear fuel. In Brazil, four research reactors were installed: the IEA-R1 and the MB-01 reactors, both at the Instituto de Pesquisas Energeticas Nucleares (IPEN, Sao Paulo); the Argonauta, at the Instituto de Engenharia Nuclear (IEN, Rio de Janeiro) and the IPR-R1 TRIGA reactor, at the Centro de Desenvolvimento da Tecnologia Nuclear (CDTN, Belo Horizonte). The present paper intends to enumerate the characteristics of these reactors, their utilization and current academic research. Therefore, through this paper, we intend to collaborate on the BMR project. (author)

  2. PERFORMANCE ANALYSIS OF MESSAGE PASSING INTERFACE COLLECTIVE COMMUNICATION ON INTEL XEON QUAD-CORE GIGABIT ETHERNET AND INFINIBAND CLUSTERS

    Directory of Open Access Journals (Sweden)

    Roswan Ismail

    2013-01-01

    Full Text Available The performance of MPI implementation operations still presents critical issues for high performance computing systems, particularly for more advanced processor technology. Consequently, this study concentrates on benchmarking MPI implementation on multi-core architecture by measuring the performance of Open MPI collective communication on Intel Xeon dual quad-core Gigabit Ethernet and InfiniBand clusters using SKaMPI. It focuses on well known collective communication routines such as MPI-Bcast, MPI-AlltoAll, MPI-Scatter and MPI-Gather. From the collection of results, MPI collective communication on InfiniBand clusters had distinctly better performance in terms of latency and throughput. The analysis indicates that the algorithm used for collective communication performed very well for all message sizes except for MPI-Bcast and MPI-Alltoall operation of inter-node communication. However, InfiniBand provides the lowest latency for all operations since it provides applications with an easy to use messaging service, compared to Gigabit Ethernet, which still requests the operating system for access to one of the server communication resources with the complex dance between an application and a network.

  3. Triple Quad-ICP-MS Measurement of Toxic Metals in Mainstream Cigarette Smoke from Spectrum Research Cigarettes.

    Science.gov (United States)

    Pappas, R Steven; Gray, Naudia; Gonzalez-Jimenez, Nathalie; Fresquez, Mark; Watson, Clifford H

    2016-01-01

    We previously reported toxic metal concentrations in the mainstream smoke from 50 varieties of commercial cigarettes available in the USA using quadrupole inductively coupled plasma-mass spectrometry (ICP-MS). However, efforts to continue producing high quality data on select mainstream cigarette smoke constituents demand continued improvements in instrumentation and methodology and application of the methodology to cigarettes that differ in design or construction. Here we report a new application of 'triple quad'-ICP-MS instrumentation to analyze seven toxic metals in mainstream cigarette smoke from the Spectrum variable nicotine research cigarettes. The Spectrum cigarettes are available for research purposes in different configurations of low or conventional levels of nicotine, mentholated or nonmentholated, and tar delivery ranges described as 'low tar' or 'high tar'. Detailed characterizations of specific harmful or potentially harmful constituents delivered by these research cigarettes will help inform researchers using these cigarettes in exposure studies, cessation studies and studies related to nicotine addiction or compensation. Published by Oxford University Press 2015. This work is written by (a) US Government employee(s) and is in the public domain in the US.

  4. Model-Based Pseudo-Quad-Pol Reconstruction from Compact Polarimetry and Its Application to Oil-Spill Observation

    Directory of Open Access Journals (Sweden)

    Junjun Yin

    2015-01-01

    Full Text Available Compact polarimetry is an effective imaging mode for wide area observation, especially for the open ocean. In this study, we propose a new method for pseudo-quad-polarization reconstruction from compact polarimetry based on the three-component decomposition. By using the decomposed powers, the reconstruction model is established as a power-weighted model. Further, the phase of the copolarized correlation is taken into consideration. The phase of double-bounce scattering is closer to π than to 0, while the phase of surface scattering is closer to 0 than to π. By considering the negative (double-bounce reflection and positive (surface reflection copolarized correlation, the reconstruction model for full polarimetry has a good consistency with the real polarimetric SAR data. L-band ALOS/PALSAR-1 fully polarimetric data acquired on August 27, 2006, over an oil-spill area are used for demonstration. Reconstruction performance is evaluated with a set of typical polarimetric oil-spill indicators. Quantitative comparison is given. Results show that the proposed model-based method is of great potential for oil-spill observation.

  5. Differential privacy two-dimensional data partitioning publication algorithm based on quad-tree%基于四分树的差分隐私二维数据划分发布算法

    Institute of Scientific and Technical Information of China (English)

    吴英杰; 卢清; 蔡剑平; 王晓东

    2016-01-01

    In order to boost the accuracy of range counting queries of the released two-dimensional space data under differential privacy,an algorithm Quad-heu based on quad-tree for differential priva-cy two-dimensional data publication by space partitioning was proposed.The basic idea of Quad-heu is to firstly construct a quad-tree with respect to the two-dimensional data and then add Laplace noise to tree nodes.After that,a bottom up heuristic approach for structural adjustment of the quad-tree was put forward,and the aim of which was to balance the noise error of queries and the error of uniform hypothesis.Finally,the accuracy of range counting queries was further reduced by post-processing the tree nodes′values through the consistency constraint of queries.Experimental analysis was designed by comparing Quad-heu and the traditional algorithms on the accuracy of range counting queries in the released data and the algorithm efficiency.Experimental results show that Quad-heu is effective and feasible.%为了提高差分隐私下二维数据区间计数查询的精度,提出一种基于四分树的差分隐私二维数据空间划分发布算法 Quad-heu.首先构建与二维数据相对应的四分树,并对树节点添加拉普拉斯噪声;然后采用启发式判断策略,自底向上对四分树结构进行调整,以达到平衡查询噪声误差和均匀假设误差的目的;最后利用查询一致性约束对添加噪声后的四分树节点进行后置处理,以进一步提高查询精度.实验对算法 Quad-heu 所发布数据的区间计数查询精度及效率与同类算法进行比较分析,结果验证了其有效性.

  6. Thermionic Reactor Design Studies

    Energy Technology Data Exchange (ETDEWEB)

    Schock, Alfred

    1994-06-01

    During the 1960's and early 70's the author performed extensive design studies, analyses, and tests aimed at thermionic reactor concepts that differed significantly from those pursued by other investigators. Those studies, like most others under Atomic Energy Commission (AEC and DOE) and the National Aeronautics and Space Administration (NASA) sponsorship, were terminated in the early 1970's. Some of this work was previously published, but much of it was never made available in the open literature. U.S. interest in thermionic reactors resumed in the early 80's, and was greatly intensified by reports about Soviet ground and flight tests in the late 80's. This recent interest resulted in renewed U.S. thermionic reactor development programs, primarily under Department of Defense (DOD) and Department of Energy (DOE) sponsorship. Since most current investigators have not had an opportunity to study all of the author's previous work, a review of the highlights of that work may be of value to them. The present paper describes some of the author's conceptual designs and their rationale, and the special analytical techniques developed to analyze their performance. The basic designs, first published in 1963, are based on single-cell converters, either double-ended diodes extending over the full height of the reactor core or single-ended diodes extending over half the core height. In that respect they are similar to the thermionic fuel elements employed in the Topaz-2 reactor subsequently developed in the Soviet Union, copies of which were recently imported by the U.S. As in the Topaz-2 case, electrically heated steady-state performance tests of the converters are possible before fueling. Where the author's concepts differed from the later Topaz-2 design was in the relative location of the emitter and the collector. Placing the fueled emitter on the outside of the cylindrical diodes permits much higher axial conductances to reduce ohmic

  7. New reactors for laboratory studies

    Energy Technology Data Exchange (ETDEWEB)

    Berty, J.M.

    1978-02-01

    Recent developments in design of laboratory and bench-scale reactors reflect mostly the developments in reaction engineering; that is the improved understanding of physical and chemical rate limiting processes, their interactions, and their effects on commercial-scale reactor performance. Whether a laboratory reactor is used to study the fundamentals of a commercial process or for pure scientific interest, it is important to know what physical or chemical process is limiting or influencing the rate and selectivity. To clarify this, a definition is required of the regime where physical influences exist, and study the intrinsic kinetics at conditions where physical processes do not affect the rate. Reactors are illustrated whose design was influenced by the above considerations. These reactors produce results which are independent of the reactors in which they were measured, and which can be scaled up with up-to-date reaction engineering techniques.

  8. Spiral-shaped disinfection reactors

    KAUST Repository

    Ghaffour, Noreddine

    2015-08-20

    This disclosure includes disinfection reactors and processes for the disinfection of water. Some disinfection reactors include a body that defines an inlet, an outlet, and a spiral flow path between the inlet and the outlet, in which the body is configured to receive water and a disinfectant at the inlet such that the water is exposed to the disinfectant as the water flows through the spiral flow path. Also disclosed are processes for disinfecting water in such disinfection reactors.

  9. Turning points in reactor design

    Energy Technology Data Exchange (ETDEWEB)

    Beckjord, E.S.

    1995-09-01

    This article provides some historical aspects on nuclear reactor design, beginning with PWR development for Naval Propulsion and the first commercial application at Yankee Rowe. Five turning points in reactor design and some safety problems associated with them are reviewed: (1) stability of Dresden-1, (2) ECCS, (3) PRA, (4) TMI-2, and (5) advanced passive LWR designs. While the emphasis is on the thermal-hydraulic aspects, the discussion is also about reactor systems.

  10. Acceptability of reactors in space

    Energy Technology Data Exchange (ETDEWEB)

    Buden, D.

    1981-04-01

    Reactors are the key to our future expansion into space. However, there has been some confusion in the public as to whether they are a safe and acceptable technology for use in space. The answer to these questions is explored. The US position is that when reactors are the preferred technical choice, that they can be used safely. In fact, it dies not appear that reactors add measurably to the risk associated with the Space Transportation System.

  11. Hydrogen Production in Fusion Reactors

    OpenAIRE

    Sudo, S.; Tomita, Y.; Yamaguchi, S.; Iiyoshi, A.; Momota, H; Motojima, O.; Okamoto, M.; Ohnishi, M.; Onozuka, M; Uenosono, C.

    1993-01-01

    As one of methods of innovative energy production in fusion reactors without having a conventional turbine-type generator, an efficient use of radiation produced in a fusion reactor with utilizing semiconductor and supplying clean fuel in a form of hydrogen gas are studied. Taking the candidates of reactors such as a toroidal system and an open system for application of the new concepts, the expected efficiency and a concept of plant system are investigated.

  12. Fast reactor programme in India

    Indian Academy of Sciences (India)

    P Chellapandi; P R Vasudeva Rao; Prabhat Kumar

    2015-09-01

    Role of fast breeder reactor (FBR) in the Indian context has been discussed with appropriate justification. The FBR programme since 1985 till 2030 is highlighted focussing on the current status and future direction of fast breeder test reactor (FBTR), prototype fast breeder reactor (PFBR) and FBR-1 and 2. Design and technological challenges of PFBR and design and safety targets with means to achieve the same are the major highlights of this paper.

  13. Neutrino Oscillation Studies with Reactors

    CERN Document Server

    Vogel, Petr; Zhang, Chao

    2015-01-01

    Nuclear reactors are one of the most intense, pure, controllable, cost-effective, and well-understood sources of neutrinos. Reactors have played a major role in the study of neutrino oscillations, a phenomenon that indicates that neutrinos have mass and that neutrino flavors are quantum mechanical mixtures. Over the past several decades reactors were used in the discovery of neutrinos, were crucial in solving the solar neutrino puzzle, and allowed the determination of the smallest mixing angle $\\theta_{13}$. In the near future, reactors will help to determine the neutrino mass hierarchy and to solve the puzzling issue of sterile neutrinos.

  14. Accelerator based fusion reactor

    Science.gov (United States)

    Liu, Keh-Fei; Chao, Alexander Wu

    2017-08-01

    A feasibility study of fusion reactors based on accelerators is carried out. We consider a novel scheme where a beam from the accelerator hits the target plasma on the resonance of the fusion reaction and establish characteristic criteria for a workable reactor. We consider the reactions d+t\\to n+α,d+{{}3}{{H}\\text{e}}\\to p+α , and p+{{}11}B\\to 3α in this study. The critical temperature of the plasma is determined from overcoming the stopping power of the beam with the fusion energy gain. The needed plasma lifetime is determined from the width of the resonance, the beam velocity and the plasma density. We estimate the critical beam flux by balancing the energy of fusion production against the plasma thermo-energy and the loss due to stopping power for the case of an inert plasma. The product of critical flux and plasma lifetime is independent of plasma density and has a weak dependence on temperature. Even though the critical temperatures for these reactions are lower than those for the thermonuclear reactors, the critical flux is in the range of {{10}22}-{{10}24}~\\text{c}{{\\text{m}}-2}~{{\\text{s}}-1} for the plasma density {ρt}={{10}15}~\\text{c}{{\\text{m}}-3} in the case of an inert plasma. Several approaches to control the growth of the two-stream instability are discussed. We have also considered several scenarios for practical implementation which will require further studies. Finally, we consider the case where the injected beam at the resonance energy maintains the plasma temperature and prolongs its lifetime to reach a steady state. The equations for power balance and particle number conservation are given for this case.

  15. Biparticle fluidized bed reactor

    Science.gov (United States)

    Scott, C.D.

    1993-12-14

    A fluidized bed reactor system which utilizes a fluid phase, a retained fluidized primary particulate phase, and a migratory second particulate phase is described. The primary particulate phase is a particle such as a gel bead containing an immobilized biocatalyst. The secondary particulate phase, continuously introduced and removed in either cocurrent or countercurrent mode, acts in a secondary role such as a sorbent to continuously remove a product or by-product constituent from the fluid phase. Introduction and removal of the sorbent phase is accomplished through the use of feed screw mechanisms and multivane slurry valves. 3 figures.

  16. FAST NEUTRONIC REACTOR

    Science.gov (United States)

    Snell, A.H.

    1957-12-01

    This patent relates to a reactor and process for carrying out a controlled fast neutron chain reaction. A cubical reactive mass, weighing at least 920 metric tons, of uranium metal containing predominantly U/sup 238/ and having a U/sup 235/ content of at least 7.63% is assembled and the maximum neutron reproduction ratio is limited to not substantially over 1.01 by insertion and removal of a varying amount of boron, the reactive mass being substantially freed of moderator.

  17. Artificial eye amplitudes and characteristics in enucleated socket with porous polyethylene spherical and quad-motility implant Amplitude de movimento e características das próteses oculares em cavidades enucleadas com implante de polietileno poroso esférico e "quad-motility"

    Directory of Open Access Journals (Sweden)

    Lucia Miriam Dumont Lucci

    2007-10-01

    Full Text Available PURPOSE: To compare artificial eye amplitudes in enucleated socket with porous polyethylene either spherical or quad-motility implant and study the characteristics of artificial eyes fit with the two orbital implants. METHODS: A total of 21 patients were prospectively studied who underwent enucleation because of an intraocular melanoma and the randomization defined a porous polyethylene either spherical or quad-motility orbital implant. Measurements of the amplitude of the artificial eye were obtained with prism and digital photos. The software Scion Image analyzed the digital photos (www.scioncorp.com and the quantitative data were allocated to groups. The measurements (height, length, thickness and weight of the 21 artificial eyes were analyzed. Student's t-test was performed to determine the significance of difference between groups (p0.05 for all directions. On analyzing the digital photos, the artificial eye with spherical implant showed higher artificial eye amplitude downward (p=0.009 among patients older than 55 years old, rightward (p=0.036 and downward (p=0.008 among the 9 patients with enucleated right eye. Height and length were similar in the 21 artificial eyes but those artificial eyes fit with quad-motility orbital implants were statistically significant thicker (pOBJETIVOS: Comparar a amplitude de movimento da prótese ocular em cavidade enucleada e com implante orbitário esférico e "quad-motility" e estudar as características das próteses oculares adaptadas com os dois modelos de implantes orbitários. MÉTODOS: Vinte e um pacientes foram prospectivamente estudados após a enucleação devido a melanoma intra-ocular e cuja randomização definiu o implante orbitário de polietileno poroso nos modelos esférico e "quad-motility". Medidas da amplitude da prótese ocular foram obtidas com prisma e fotografia digital. O programa Scion Image analisou as fotos digitais (www.scioncorp.com e os resultados foram distribuídos por

  18. Licensed reactor nuclear safety criteria applicable to DOE reactors

    Energy Technology Data Exchange (ETDEWEB)

    1991-04-01

    The Department of Energy (DOE) Order DOE 5480.6, Safety of Department of Energy-Owned Nuclear Reactors, establishes reactor safety requirements to assure that reactors are sited, designed, constructed, modified, operated, maintained, and decommissioned in a manner that adequately protects health and safety and is in accordance with uniform standards, guides, and codes which are consistent with those applied to comparable licensed reactors. This document identifies nuclear safety criteria applied to NRC (Nuclear Regulatory Commission) licensed reactors. The titles of the chapters and sections of USNRC Regulatory Guide 1.70, Standard Format and Content of Safety Analysis Reports for Nuclear Power Plants, Rev. 3, are used as the format for compiling the NRC criteria applied to the various areas of nuclear safety addressed in a safety analysis report for a nuclear reactor. In each section the criteria are compiled in four groups: (1) Code of Federal Regulations, (2) US NRC Regulatory Guides, SRP Branch Technical Positions and Appendices, (3) Codes and Standards, and (4) Supplemental Information. The degree of application of these criteria to a DOE-owned reactor, consistent with their application to comparable licensed reactors, must be determined by the DOE and DOE contractor.

  19. Fast Reactor Fuel Type and Reactor Safety Performance

    Energy Technology Data Exchange (ETDEWEB)

    R. Wigeland; J. Cahalan

    2009-09-01

    Fast Reactor Fuel Type and Reactor Safety Performance R. Wigeland , Idaho National Laboratory J. Cahalan, Argonne National Laboratory The sodium-cooled fast neutron reactor is currently being evaluated for the efficient transmutation of the highly-hazardous, long-lived, transuranic elements that are present in spent nuclear fuel. One of the fundamental choices that will be made is the selection of the fuel type for the fast reactor, whether oxide, metal, carbide, nitride, etc. It is likely that a decision on the fuel type will need to be made before many of the related technologies and facilities can be selected, from fuel fabrication to spent fuel reprocessing. A decision on fuel type should consider all impacts on the fast reactor system, including safety. Past work has demonstrated that the choice of fuel type may have a significant impact on the severity of consequences arising from accidents, especially for severe accidents of low probability. In this paper, the response of sodium-cooled fast reactors is discussed for both oxide and metal fuel types, highlighting the similarities and differences in reactor response and accident consequences. Any fast reactor facility must be designed to be able to successfully prevent, mitigate, or accommodate all consequences of potential events, including accidents. This is typically accomplished by using multiple barriers to the release of radiation, including the cladding on the fuel, the intact primary cooling system, and most visibly the reactor containment building. More recently, this has also included the use of ‘inherent safety’ concepts to reduce or eliminate the potential for serious damage in some cases. Past experience with oxide and metal fuel has demonstrated that both fuel types are suitable for use as fuel in a sodium-cooled fast reactor. However, safety analyses for these two fuel types have also shown that there can be substantial differences in accident consequences due to the neutronic and

  20. Reactor Physics Analysis Models for a CANDU Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Hang Bok

    2007-10-15

    Canada deuterium uranium (CANDU) reactor physics analysis is typically performed in three steps. At first, macroscopic cross-sections of the reference lattice is produced by modeling the reference fuel channel. Secondly macroscopic cross-sections of reactivity devices in the reactor are generated. The macroscopic cross-sections of a reactivity device are calculated as incremental cross-sections by subtracting macroscopic cross-sections of a three-dimensional lattice without reactivity device from those of a three-dimensional lattice with a reactivity device. Using the macroscopic cross-sections of the reference lattice and incremental cross-sections of the reactivity devices, reactor physics calculations are performed. This report summarizes input data of typical CANDU reactor physics codes, which can be utilized for the future CANDU reactor physics analysis.

  1. Reactor Physics Analysis Models for a CANDU Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Hang Bok

    2007-10-15

    Canada deuterium uranium (CANDU) reactor physics analysis is typically performed in three steps. At first, macroscopic cross-sections of the reference lattice is produced by modeling the reference fuel channel. Secondly macroscopic cross-sections of reactivity devices in the reactor are generated. The macroscopic cross-sections of a reactivity device are calculated as incremental cross-sections by subtracting macroscopic cross-sections of a three-dimensional lattice without reactivity device from those of a three-dimensional lattice with a reactivity device. Using the macroscopic cross-sections of the reference lattice and incremental cross-sections of the reactivity devices, reactor physics calculations are performed. This report summarizes input data of typical CANDU reactor physics codes, which can be utilized for the future CANDU reactor physics analysis.

  2. Static test on aerodynamic characteristics of iced quad bundled conductors%覆冰四分裂导线静态气动力特性试验

    Institute of Scientific and Technical Information of China (English)

    张宏雁; 严波; 周松; 胡景; 刘小会

    2011-01-01

    The aerodynamic characteristics of iced quad bundled conductor may be different from those of iced single conductor because of the wake interference around the sub-conductors of the bundled conductor.Test models of iced quad bundled conductors with two different cross section shapes of ice were prepared.The static aerodynamic coefficients of the models varying with attack angle, in the cases of different ice thickness and wind velocities, are obtained by wind tunnel test.It is observed that the wake interference around sub-conductors on the aerodynamic coefficients is obvious under certain wind attack angles.The obtained tests provide basic data for the analysis of galloping of iced quad bundled conductor and the development of anti-galloping technology.%覆冰四分裂导线的空气动力特性,由于覆冰子导线尾流的相互干扰可能不同于覆冰单导线.针对两种不同冰型制作覆冰四分裂导线模型,通过风洞试验测试获得不同冰厚和不同风速下覆冰四分裂导线静态空气动力系数随攻角的变化曲线.结果表明,在一定的攻角下,子导线尾流相互干扰对空气动力系数有明显影响.所得试验结果为覆冰四分裂导线的舞动及其防止技术的研究提供必要的数据.

  3. A comparison of three-dimensional stress distribution and displacement of naso-maxillary complex on application of forces using quad-helix and nickel titanium palatal expander 2 (NPE2: a FEM study

    Directory of Open Access Journals (Sweden)

    Avinash Kumar

    2016-06-01

    Full Text Available Abstract Background Our objectives are to analyse and to compare the stress distribution and displacement of the craniofacial structures, following the application of forces from quad-helix and Nickel Titanium Palatal Expander-2 (NPE2 using finite element analysis. Methods Three-dimensional finite element models of young dried human skull, quad-helix appliance and NPE2 were constructed, and the initial activation of the expanders was stimulated to carry out the analysis and to evaluate the Von Misses stresses and displacement. Results Both the models demonstrated the highest stresses at the mid-palatal suture, with maximum posterior dislocation. The second highest stress was recorded at the fronto-zygomatic suture. The pattern of stress distribution was almost similar in both the groups, but NPE2 revealed lower magnitude stresses than quad-helix. The only exception being quad-helix model showed high stress levels around pterygo-maxillary suture whereas minimal stress around pterygo-maxillary suture was noticed after NPE2 activation. The cusp of the erupting canine and the erupting mesiobuccal cusp of the second molar showed outward, backward and downward displacement signifying increase in their eruption pattern following maxillary expansion. Conclusions Maxillary expansion using quad-helix and NPE2 can be used in posterior crossbite correction in cases where maximum skeletal changes are desirable at a younger age; it is furthermore effective in treating young patients with impacted or displaced teeth. Quad-helix and NPE2 produced acceptable forces for orthopaedic treatment even after being orthodontic appliances; their clinical application should be correctly planned as the effects of these appliances are largely age dependent.

  4. A summary of the osteosarcoma banking efforts: a report from the Children's Oncology Group and the QuadW Foundation.

    Science.gov (United States)

    Glover, Jason; Krailo, Mark; Tello, Tanya; Marina, Neyssa; Janeway, Katherine; Barkauskas, Don; Fan, Timothy M; Gorlick, Richard; Khanna, Chand

    2015-03-01

    Survival rates of patients with osteosarcoma have remained stagnant over the last thirty years. Better understanding of biology, new therapeutics, and improved biomarkers are needed. The Children's Oncology Group (COG) addressed this need by developing one of the largest osteosarcoma biorepositories ever, containing over 15,000 tumor and tissue samples from over 1,500 patients. The biology study P9851 and the banking study AOST06B1 has enrolled 1,787 patients (as of September, 2013). Clinical information was lacking on 510 patients on P9851, who were not enrolled on a concurrent therapeutic trial. The value of these specimens was diminished. The lack of statistical support available for biology projects slowed the analysis of several critical studies. The QuadW Foundation, CureSearch, and the COG formed the Childhood Sarcoma Biostatistics and Annotation Office (CSBAO) to provide the infrastructure and address these needs by linking clinically annotated patient data to archived tissue samples and to develop biostatistical support for childhood sarcoma research. Originally 5.3% of samples from the 510 patients on P9851 not enrolled on a therapeutic study had full clinical annotation. The efforts of the CSBAO have linked clinical annotation to 90.8% of those specimens and provided statistical analyses to several studies that had used COG samples. As a result, 24 biology studies in osteosarcoma have been completed and published in peer-reviewed journals. These samples and in-silico data are available to the research community for basic and translational science projects to improve the biological understanding and treatment of patients affected by osteosarcoma. © 2014 Wiley Periodicals, Inc.

  5. Chemical-vapor-deposition reactor

    Science.gov (United States)

    Chern, S.

    1979-01-01

    Reactor utilizes multiple stacked trays compactly arranged in paths of horizontally channeled reactant gas streams. Design allows faster and more efficient deposits of film on substrates, and reduces gas and energy consumption. Lack of dead spots that trap reactive gases reduces reactor purge time.

  6. Thermochemical reactor systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Lipinski, Wojciech; Davidson, Jane Holloway; Chase, Thomas Richard

    2016-11-29

    Thermochemical reactor systems that may be used to produce a fuel, and methods of using the thermochemical reactor systems, utilizing a reactive cylindrical element, an optional energy transfer cylindrical element, an inlet gas management system, and an outlet gas management system.

  7. Test reactor risk assessment methodology

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, R.H.; Rawlins, J.K.; Stewart, M.E.

    1976-04-01

    A methodology has been developed for the identification of accident initiating events and the fault modeling of systems, including common mode identification, as these methods are applied in overall test reactor risk assessment. The methods are exemplified by a determination of risks to a loss of primary coolant flow in the Engineering Test Reactor.

  8. Studies on a membrane reactor

    Energy Technology Data Exchange (ETDEWEB)

    Mohan, K.; Govind, R.

    1988-10-01

    Simulation is used to evaluate the performance of a catalytic reactor with permeable wall (membrane reactor) in shifting the equilibrium of three reversible reactions (cyclohexane dehydrogenation, hydrogen iodide decomposition, and propylene disproportionation). It is found that the preferred choice of cocurrernt or countercurrent operation is dependent on the physical properties and operating conditions. Methods of enhancing conversion are suggested and temperature effects are discussed.

  9. Thermochemical reactor systems and methods

    Science.gov (United States)

    Lipinski, Wojciech; Davidson, Jane Holloway; Chase, Thomas Richard

    2016-11-29

    Thermochemical reactor systems that may be used to produce a fuel, and methods of using the thermochemical reactor systems, utilizing a reactive cylindrical element, an optional energy transfer cylindrical element, an inlet gas management system, and an outlet gas management system.

  10. Brookhaven leak reactor to close

    CERN Multimedia

    MacIlwain, C

    1999-01-01

    The DOE has announced that the High Flux Beam Reactor at Brookhaven is to close for good. Though the news was not unexpected researchers were angry the decision had been taken before the review to assess the impact of reopening the reactor had been concluded (1 page).

  11. 基于anti-windup技术的四旋翼模糊PID控制%Fuzzy PID Control of Quad-Rotor Aircraft Based on Anti-windup Technology

    Institute of Scientific and Technical Information of China (English)

    耿玉豪; 肖文生; 崔俊国; 王鸿雁

    2016-01-01

    When quad-rotor aircraft is trapped in the great disturbance of wind, windup phenomenon may appear for simple PID controller, under the combined action of integration element and saturation limit element. Thus may lead to deterioration of system’s dynamic responses, and big overshoot or imbalance of quad-rotor. A dynamics simulation model is established for the quad-rotor aircraft, and the causes of windup phenomenon are analyzed. An anti-windup PID controller with fuzzy variable parameters is designed to alleviate the windup phenomenon. Contrastive analysis is made to the controller with the existing fuzzy PID controller and the anti-windup PID controller with constant parameters. The results of simulation indicate that, the fuzzy PID controller based on anti-windup technology can effectively restrain the windup phenomenon, and speed up the attitude adjustment process of quad-rotor.%四旋翼飞行器在受到风力等大扰动的情况下,单纯的PID控制受到积分环节和饱和限幅环节的共同作用,容易产生windup现象,系统动态响应变差,造成飞行器大超调甚至失调。通过建立四旋翼飞行器的动力学仿真模型,分析了windup现象产生的原因,设计了参数模糊可变的anti-windup PID控制器,用于缓解windup现象。对比分析了该控制器与现有的模糊PID控制器、参数为定值的anti-windup PID控制器的性能,仿真结果表明,基于anti-windup技术的模糊PID控制器,能够更加有效地抑制windup现象,加快飞行器的姿态调节过程。

  12. Generación y transmisión de órdenes de movimiento a un vehículo tipo Quad

    OpenAIRE

    ARBONA DE LA ASUNCIÓN, CARMEN

    2011-01-01

    El objetivo principal de este Proyecto Final de Carrea es desarrollar una plataforma software que realice la conducción automatizada de un vehículo autónomo tipo Quad. Esta plataforma software transmitirá órdenes al sistema de frenado, aceleración y dirección para la conducción del citado vehículo. Esta aplicación tiene la finalidad de servir de soporte para el estudio de diferentes métodos de planificación de caminos, es decir, intenta ser una herramienta que facilite el estudio y mejoras de...

  13. Metallic fuels for advanced reactors

    Science.gov (United States)

    Carmack, W. J.; Porter, D. L.; Chang, Y. I.; Hayes, S. L.; Meyer, M. K.; Burkes, D. E.; Lee, C. B.; Mizuno, T.; Delage, F.; Somers, J.

    2009-07-01

    In the framework of the Generation IV Sodium Fast Reactor Program, the Advanced Fuel Project has conducted an evaluation of the available fuel systems supporting future sodium cooled fast reactors. This paper presents an evaluation of metallic alloy fuels. Early US fast reactor developers originally favored metal alloy fuel due to its high fissile density and compatibility with sodium. The goal of fast reactor fuel development programs is to develop and qualify a nuclear fuel system that performs all of the functions of a conventional fast spectrum nuclear fuel while destroying recycled actinides. This will provide a mechanism for closure of the nuclear fuel cycle. Metal fuels are candidates for this application, based on documented performance of metallic fast reactor fuels and the early results of tests currently being conducted in US and international transmutation fuel development programs.

  14. A model of reactor kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, A.S.; Thompson, B.R.

    1988-09-01

    The analytical model of nuclear reactor transients, incorporating both mechanical and nuclear effects, simulates reactor kinetics. Linear analysis shows the stability borderline for small power perturbations. In a stable system, initial power disturbances die out with time. With an unstable combination of nuclear and mechanical characteristics, initial disturbances persist and may increase with time. With large instability, oscillations of great magnitude occur. Stability requirements set limits on the power density at which particular reactors can operate. The limiting power density depends largely on the product of two terms: the fraction of delayed neutrons and the frictional damping of vibratory motion in reactor core components. As the fraction of delayed neutrons is essentially fixed, mechanical damping largely determines the maximum power density. A computer program, based on the analytical model, calculates and plots reactor power as a nonlinear function of time in response to assigned values of mechanical and nuclear characteristics.

  15. Engineering reactors for catalytic reactions

    Indian Academy of Sciences (India)

    Vivek V Ranade

    2014-03-01

    Catalytic reactions are ubiquitous in chemical and allied industries. A homogeneous or heterogeneous catalyst which provides an alternative route of reaction with lower activation energy and better control on selectivity can make substantial impact on process viability and economics. Extensive studies have been conducted to establish sound basis for design and engineering of reactors for practising such catalytic reactions and for realizing improvements in reactor performance. In this article, application of recent (and not so recent) developments in engineering reactors for catalytic reactions is discussed. Some examples where performance enhancement was realized by catalyst design, appropriate choice of reactor, better injection and dispersion strategies and recent advances in process intensification/ multifunctional reactors are discussed to illustrate the approach.

  16. Unsteady processes in catalytic reactors

    Energy Technology Data Exchange (ETDEWEB)

    Matros, Yu.Sh.

    1985-01-01

    In recent years a realization has occurred that reaction and reactor dynamics must be considered when designing and operating catalytic reactors. In this book, the author has focussed on both the processes occurring on individual porous-catalyst particles as well as the phenomena displayed by collections of these particles in fixed-bed reactors. The major topics discussed include the effects of unsteady-state heat and mass transfer, the influence of inhomogeneities and stagnant regions in fixed beds, and reactor operation during forced cycling of operating conditions. Despite the title of the book, attention is also paid to the determination of the number and stability of fixed-bed steady states, with the aim of describing the possibility of controlling reactors at unstable steady states. However, this development is somewhat dated, given the recent literature on multiplicity phenomena and process control.

  17. Antineutrino Monitoring of Thorium Reactors

    CERN Document Server

    Akindele, Oluwatomi A; Norman, Eric B

    2015-01-01

    Various groups have demonstrated that antineutrino monitoring can be successful in assessing the plutonium content in water-cooled nuclear reactors for nonproliferation applications. New reactor designs and concepts incorporate nontraditional fuels types and chemistry. Understanding how these properties affect the antineutrino emission from a reactor can extend the applicability of antineutrino monitoring.Thorium molten salt reactors (MSR) breed U-233, that if diverted constitute an IAEA direct use material. The antineutrino spectrum from the fission of U-233 has been determined, the feasibility of detecting the diversion of a significant quantity, 8 kg of U-233, within the IAEA timeliness goal of 30 days has been evaluated. The antineutrino emission from a thorium reactor operating under normal conditions is compared to a diversion scenario at a 25 meter standoff by evaluating the daily antineutrino count rate and the energy spectrum of the detected antineutrinos. It was found that the diversion of a signifi...

  18. Licensed reactor nuclear safety criteria applicable to DOE reactors

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    This document is a compilation and source list of nuclear safety criteria that the Nuclear Regulatory Commission (NRC) applies to licensed reactors; it can be used by DOE and DOE contractors to identify NRC criteria to be evaluated for application to the DOE reactors under their cognizance. The criteria listed are those that are applied to the areas of nuclear safety addressed in the safety analysis report of a licensed reactor. They are derived from federal regulations, USNRC regulatory guides, Standard Review Plan (SRP) branch technical positions and appendices, and industry codes and standards.

  19. University Reactor Conversion Lessons Learned Workshop for Purdue University Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Eric C. Woolstenhulme; Dana M. Hewit

    2008-09-01

    The Department of Energy’s Idaho National Laboratory, under its programmatic responsibility for managing the University Research Reactor Conversions, has completed the conversion of the reactor at Purdue University Reactor. With this work completed and in anticipation of other impending conversion projects, the INL convened and engaged the project participants in a structured discussion to capture the lessons learned. The lessons learned process has allowed us to capture gaps, opportunities, and good practices, drawing from the project team’s experiences. These lessons will be used to raise the standard of excellence, effectiveness, and efficiency in all future conversion projects.

  20. Neutronic Reactor Shield

    Science.gov (United States)

    Fermi, Enrico; Zinn, Walter H.

    The argument of the present Patent is a radiation shield suitable for protection of personnel from both gamma rays and neutrons. Such a shield from dangerous radiations is achieved to the best by the combined action of a neutron slowing material (a moderator) and a neutron absorbing material. Hydrogen is particularly effective for this shield since it is a good absorber of slow neutrons and a good moderator of fast neutrons. The neutrons slowed down by hydrogen may, then, be absorbed by other materials such as boron, cadmium, gadolinium, samarium or steel. Steel is particularly convenient for the purpose, given its effectiveness in absorbing also the gamma rays from the reactor (both primary gamma rays and secondary ones produced by the moderation of neutrons). In particular, in the present Patent a shield is described, made of alternate layers of steel and Masonite (an hydrolized ligno-cellulose material). The object of the present Patent is not discussed in any other published paper.

  1. Neutrino Experiments at Reactors

    Science.gov (United States)

    Reines, F.; Gurr, H. S.; Jenkins, T. L.; Munsee, J. H.

    1968-09-09

    A description is given of the electron-antineutrino program using a large fission reactor. A search has been made for a neutral weak interaction via the reaction (electron antineutrino + d .> p + n + electron antineutrino), the reaction (electron antineutrino + d .> n + n + e{sup +}) has now been detected, and an effort is underway to observe the elastic scattering reaction (electron antineutrino + e{sup -} .> electron antineutrino + e{sup -}) as well as to measure more precisely the reaction (electron antineutrino + p .> n + e{sup+}). The upper limit on the elastic scattering reaction which we have obtained with our large composite NaI, plastic, liquid scintillation detector is now about 50 times the predicted value.

  2. Reactor service life extension program

    Energy Technology Data Exchange (ETDEWEB)

    Caskey, G.R.; Sindelar, R.L.; Ondrejcin, R.S.; Baumann, E.W.

    1990-12-31

    A review of the Savannah River Site production reactor systems was initiated in 1980 and led to implementation of the Reactor Materials Program in 1984 to assess reactor safety and reactor service life. The program evaluated performance of the reactor tanks, primary coolant piping, and thermal shields, components of welded construction that were fabricated from Type 304 stainless steel. The structural integrity analysis of the primary coolant system has shown that the pressure boundary is not susceptible to gross rupture, including a double ended guillotine break or equivalent large area bank. Residual service life is potentially limited by two material degradation modes, irradiation damage and intergranular stress corrosion cracking. Analysis of the structural integrity of the tanks and piping has shown that continued safe operation of the reactors for several additional decades is not limited by the material performance of the primary coolant system. Although irradiation damage has not degraded material behavior to an unacceptable level, past experience has revealed serious difficulties with repair welding on irradiated stainless steel. Stress corrosion can be mitigated by newly identified limits on impurity concentrations in the coolant water and by stress mitigation of weld residual stresses. Work continues in several areas: the effects of helium on mechanical behavior of irradiated stainless steel; improved weld methods for piping and the reactor tanks; and a surveillance program to track irradiation effects on the tank walls.

  3. Reactor service life extension program

    Energy Technology Data Exchange (ETDEWEB)

    Caskey, G.R.; Sindelar, R.L.; Ondrejcin, R.S.; Baumann, E.W.

    1990-01-01

    A review of the Savannah River Site production reactor systems was initiated in 1980 and led to implementation of the Reactor Materials Program in 1984 to assess reactor safety and reactor service life. The program evaluated performance of the reactor tanks, primary coolant piping, and thermal shields, components of welded construction that were fabricated from Type 304 stainless steel. The structural integrity analysis of the primary coolant system has shown that the pressure boundary is not susceptible to gross rupture, including a double ended guillotine break or equivalent large area bank. Residual service life is potentially limited by two material degradation modes, irradiation damage and intergranular stress corrosion cracking. Analysis of the structural integrity of the tanks and piping has shown that continued safe operation of the reactors for several additional decades is not limited by the material performance of the primary coolant system. Although irradiation damage has not degraded material behavior to an unacceptable level, past experience has revealed serious difficulties with repair welding on irradiated stainless steel. Stress corrosion can be mitigated by newly identified limits on impurity concentrations in the coolant water and by stress mitigation of weld residual stresses. Work continues in several areas: the effects of helium on mechanical behavior of irradiated stainless steel; improved weld methods for piping and the reactor tanks; and a surveillance program to track irradiation effects on the tank walls.

  4. Assessment of torsatrons as reactors

    Energy Technology Data Exchange (ETDEWEB)

    Lyon, J.F. (Oak Ridge National Lab., TN (United States)); Painter, S.L. (Australian National Univ., Canberra, ACT (Australia))

    1992-12-01

    Stellarators have significant operational advantages over tokamaks as ignited steady-state reactors because stellarators have no dangerous disruptions and no need for continuous current drive or power recirculated to the plasma, both easing the first wall, blanket, and shield design; less severe constraints on the plasma parameters and profiles; and better access for maintenance. This study shows that a reactor based on the torsatron configuration (a stellarator variant) could also have up to double the mass utilization efficiency (MUE) and a significantly lower cost of electricity (COE) than a conventional tokamak reactor (ARIES-I) for a range of assumptions. Torsatron reactors can have much smaller coil systems than tokamak reactors because the coils are closer to the plasma and they have a smaller cross section (higher average current density because of the lower magnetic field). The reactor optimization approach and the costing and component models are those used in the current stage of the ARIES-I tokamak reactor study. Typical reactor parameters for a 1-GW(e) Compact Torsatron reactor example are major radius R[sub 0] = 6.6-8.8 m, on-axis magnetic field B[sup 0] = 4.8-7.5 T, B[sub max] (on coils) = 16 T, MUE 140-210 kW(e)/tonne, and COE (in constant 1990 dollars) = 67-79 mill/kW(e)h. The results are relatively sensitive to assumptions on the level of confinement improvement and the blanket thickness under the inboard half of the helical windings but relatively insensitive to other assumptions.

  5. Front Room Monitoring System Multi Quad Analytical Equipment%前端机房监看系统多画面分割器设备解析

    Institute of Scientific and Technical Information of China (English)

    钟红英

    2015-01-01

    多画面分割器作为有线电视前端机房播监看系统的核心处理部件,其性能对整个机房监控系统的有效性和稳定性起着举足轻重的作用,阐述了多画面分割器的主要评测指标,并结合国内外主流产品的功能与性能进行分析。%Multi Quad as cable headend broadcast monitor core processing component of the system,its per-formance is slightly superior to the effectiveness and stability of the whole room monitoring system plays an im-portant role.This paper reviews the main indicators of more elaborate Quad,and combined with the function-ality and performance of mainstream products at home and abroad for analysis.

  6. Safety of VVER-440 reactors

    CERN Document Server

    Slugen, Vladimir

    2011-01-01

    Safety of VVER-440 Reactors endeavours to promote an increase in the safety of VVER-440 nuclear reactors via the improvement of fission products limitation systems and the implementation of special non-destructive spectroscopic methods for materials testing. All theoretical and experimental studies performed the by author over the last 25 years have been undertaken with the aim of improving VVER-440 defence in depth, which is one of the most important principle for ensuring safety in nuclear power plants. Safety of VVER-440 Reactors is focused on the barrier system through which the safety pri

  7. Random processes in nuclear reactors

    CERN Document Server

    Williams, M M R

    1974-01-01

    Random Processes in Nuclear Reactors describes the problems that a nuclear engineer may meet which involve random fluctuations and sets out in detail how they may be interpreted in terms of various models of the reactor system. Chapters set out to discuss topics on the origins of random processes and sources; the general technique to zero-power problems and bring out the basic effect of fission, and fluctuations in the lifetime of neutrons, on the measured response; the interpretation of power reactor noise; and associated problems connected with mechanical, hydraulic and thermal noise sources

  8. Reactor neutrons in nuclear astrophysics

    Science.gov (United States)

    Reifarth, René; Glorius, Jan; Göbel, Kathrin; Heftrich, Tanja; Jentschel, Michael; Jurado, Beatriz; Käppeler, Franz; Köster, Ulli; Langer, Christoph; Litvinov, Yuri A.; Weigand, Mario

    2017-09-01

    The huge neutron fluxes offer the possibility to use research reactors to produce isotopes of interest, which can be investigated afterwards. An example is the half-lives of long-lived isotopes like 129I. A direct usage of reactor neutrons in the astrophysical energy regime is only possible, if the corresponding ions are not at rest in the laboratory frame. The combination of an ion storage ring with a reactor and a neutron guide could open the path to direct measurements of neutron-induced cross sections on short-lived radioactive isotopes in the astrophysically interesting energy regime.

  9. Concept for LEU Burst Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Steven Karl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kimpland, Robert Herbert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-07

    Design and performance of a proposed LEU burst reactor are sketched. Salient conclusions reached are the following: size would be ~1,500 kg or greater, depending on the size of the central cavity; internal stresses during burst require split rings for relief; the reactor would likely require multiple control and safety rods for fine control; the energy spectrum would be comparable to that of HEU machines; and burst yields and steady-state power levels will be significantly greater in an LEU reactor.

  10. Nuclear reactor downcomer flow deflector

    Energy Technology Data Exchange (ETDEWEB)

    Gilmore, Charles B. (Greensburg, PA); Altman, David A. (Pittsburgh, PA); Singleton, Norman R. (Murrysville, PA)

    2011-02-15

    A nuclear reactor having a coolant flow deflector secured to a reactor core barrel in line with a coolant inlet nozzle. The flow deflector redirects incoming coolant down an annulus between the core barrel and the reactor vessel. The deflector has a main body with a front side facing the fluid inlet nozzle and a rear side facing the core barrel. The rear side of the main body has at least one protrusion secured to the core barrel so that a gap exists between the rear side of the main body adjacent the protrusion and the core barrel. Preferably, the protrusion is a relief that circumscribes the rear side of the main body.

  11. Fuel Fabrication and Nuclear Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Karpius, Peter Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-02

    The uranium from the enrichment plant is still in the form of UF6. UF6 is not suitable for use in a reactor due to its highly corrosive chemistry as well as its phase diagram. UF6 is converted into UO2 fuel pellets, which are in turn placed in fuel rods and assemblies. Reactor designs are variable in moderators, coolants, fuel, performance etc.The dream of energy ‘too-cheap to meter’ is no more, and now the nuclear power industry is pushing ahead with advanced reactor designs.

  12. Nuclear reactor PBMR and cogeneration; Reactor nuclear PBMR y cogeneracion

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez S, J. R.; Alonso V, G., E-mail: ramon.ramirez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    In recent years the nuclear reactor designs for the electricity generation have increased their costs, so that at the moment costs are managed of around the 5000 US D for installed kw, reason for which a big nuclear plant requires of investments of the order of billions of dollars, the designed reactors as modular of low power seek to lighten the initial investment of a big reactor dividing the power in parts and dividing in modules the components to lower the production costs, this way it can begin to build a module and finished this to build other, differing the long term investment, getting less risk therefore in the investment. On the other hand the reactors of low power can be very useful in regions where is difficult to have access to the electric net being able to take advantage of the thermal energy of the reactor to feed other processes like the water desalination or the vapor generation for the processes industry like the petrochemical, or even more the possible hydrogen production to be used as fuel. In this work the possibility to generate vapor of high quality for the petrochemical industry is described using a spheres bed reactor of high temperature. (Author)

  13. Breeder Reactors, Understanding the Atom Series.

    Science.gov (United States)

    Mitchell, Walter, III; Turner, Stanley E.

    The theory of breeder reactors in relationship to a discussion of fission is presented. Different kinds of reactors are characterized by the cooling fluids used, such as liquid metal, gas, and molten salt. The historical development of breeder reactors over the past twenty-five years includes specific examples of reactors. The location and a brief…

  14. Evolution of the tandem mirror reactor concept

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, G.A.; Logan, B.G.

    1982-03-09

    We discuss the evolution of the tandem mirror reactor concept from the original conceptual reactor design (1977) through the first application of the thermal barrier concept to a reactor design (1979) to the beginning of the Mirror Advanced Reactor Study (1982).

  15. FASTER Test Reactor Preconceptual Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Grandy, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Belch, H. [Argonne National Lab. (ANL), Argonne, IL (United States); Brunett, A. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Heidet, F. [Argonne National Lab. (ANL), Argonne, IL (United States); Hill, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Hoffman, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Jin, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Mohamed, W. [Argonne National Lab. (ANL), Argonne, IL (United States); Moisseytsev, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Passerini, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Sienicki, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Sumner, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Vilim, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Hayes, S. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-03-31

    The FASTER test reactor plant is a sodium-cooled fast spectrum test reactor that provides high levels of fast and thermal neutron flux for scientific research and development. The 120MWe FASTER reactor plant has a superheated steam power conversion system which provides electrical power to a local grid allowing for recovery of operating costs for the reactor plant.

  16. FASTER test reactor preconceptual design report summary

    Energy Technology Data Exchange (ETDEWEB)

    Grandy, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Belch, H. [Argonne National Lab. (ANL), Argonne, IL (United States); Brunett, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Heidet, F. [Argonne National Lab. (ANL), Argonne, IL (United States); Hill, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Hoffman, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Jin, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Mohamed, W. [Argonne National Lab. (ANL), Argonne, IL (United States); Moisseytsev, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Passerini, S. [Argonne National Lab. (ANL), Argonne, IL (United States); Sienicki, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Sumner, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Vilim, R. [Argonne National Lab. (ANL), Argonne, IL (United States); Hayes, Steven [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-02-29

    The FASTER reactor plant is a sodium-cooled fast spectrum test reactor that provides high levels of fast and thermal neutron flux for scientific research and development. The 120MWe FASTER reactor plant has a superheated steam power conversion system which provides electrical power to a local grid allowing for recovery of operating costs for the reactor plant.

  17. ADAPTIVE CONTROL SYSTEM OF INDUSTRIAL REACTORS

    Directory of Open Access Journals (Sweden)

    Vyacheslav K. Mayevski

    2014-01-01

    Full Text Available This paper describes a mathematical model of an industrial chemical reactor for production of synthetic rubber. During reactor operation the model parameters vary considerably. To create a control algorithm performed transformation of mathematical model of the reactor in order to obtain a dependency that can be used to determine the model parameters are changing during reactor operation.

  18. Nuclear research reactors activities in INVAP

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez, Juan Pablo [INVAP, Bariloche (Argentina)

    2013-07-01

    This presentation describes the different activities in the research reactor field that are being carried out by INVAP. INVAP is presently involved in the design of three new research reactors in three different countries. The RA-10 is a multipurpose reactor, in Argentina, planned as a replacement for the RA-3 reactor. INVAP was contracted by CNEA for carrying out the preliminary engineering for this reactor, and has recently been contracted by CNEA for the detailed engineering. CNEA groups are strongly involved in the design of this reactor. The RMB is a multipurpose reactor, planned by CNEN from Brazil. CNEN, through REDETEC, has contracted INVAP to carry out the preliminary engineering for this reactor. As the user requirements for RA-10 and RMB are very similar, an agreement was signed between Argentina and Brasil governments to cooperate in these two projects. The agreement included that both reactors would use the OPAL reactor in Australia, design and built by INVAP, as a reference reactor. INVAP has also designed the LPRR reactor for KACST in Saudi Arabia. The LPRR is a 30 kw reactor for educational purposes. KACST initially contracted INVAP for the engineering for this reactor and has recently signed the contract with INVAP for building the reactor. General details of these three reactors will be presented.

  19. Effect of Manufacturing Stresses to Die Attach Film Performance In Quad Flatpack No-Lead Stacked Die Packages

    Directory of Open Access Journals (Sweden)

    M. F. Rosle

    2009-01-01

    Full Text Available Problem statement: Repeated heat cure during assembly processes affected the Die Attach Film (DAF material properties and the effectiveness touched area that leads to weak die bonding and delamination. Suitable die attached condition and DAF material selection had been evaluated to achieve required reliability performance in the manufacturing of the 3D Quad Flat No-Lead (QFN stacked die package. Approach: During this study, special attention was given to the development of the residual stresses due to mismatch in the coefficients of thermal expansion of different DAF materials. Both experimental and finite element method were employed to gain a better understanding in a stress development induced between two different type of DAF, different die attach temperature and during the manufacturing process. Differential scanning calorimetry (DSC was used to measure the changes of heat flow characteristics for both types of DAF. The die bond strength results measured using shear testing machine were compared with the finite element method prediction. Results: Although both DAF samples achieved good reliability performance and passed the Moisture Sensitivity Level 3 test (MSL3 at reflow 260°C without any sign of delamination, numerical simulation had demonstrated that the stress development were increased exponentially as the die attach temperature increased. It showed that different DAF gave different values of stresses but presented the same trend which the lowest die attached temperature (100°C in comparison with 125°C and 150°C gave more stress to the die and possibility that the die will have weak adhesion to the substrate was high. Conclusions/Recommendations: Therefore for this case, stress can be relieved by having higher die attached temperature with an adequate bonding force and time, however die attached temperature for both DAF must be used above the glass transition temperature (128°C for DAF A and 165°C for DAF B and being controlled

  20. Advanced Carbothermal Electric Reactor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall objective of the Phase 1 effort was to demonstrate the technical feasibility of the Advanced Carbothermal Electric (ACE) Reactor concept. Unlike...

  1. Thermal Analysis for Mobile Reactor

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Mobile reactor design in the paper is consisted of two grades of thermal electric conversion. The first grade is the thermionic conversion inside the core and the second grade is thermocouple conversion

  2. Advanced Carbothermal Electric Reactor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ORBITEC proposes to develop the Advanced Carbothermal Electric (ACE) reactor to efficiently extract oxygen from lunar regolith. Unlike state-of-the-art carbothermal...

  3. Teaching About Nature's Nuclear Reactors

    CERN Document Server

    Herndon, J M

    2005-01-01

    Naturally occurring nuclear reactors existed in uranium deposits on Earth long before Enrico Fermi built the first man-made nuclear reactor beneath Staggs Field in 1942. In the story of their discovery, there are important lessons to be learned about scientific inquiry and scientific discovery. Now, there is evidence to suggest that the Earth's magnetic field and Jupiter's atmospheric turbulence are driven by planetary-scale nuclear reactors. The subject of planetocentric nuclear fission reactors can be a jumping off point for stimulating classroom discussions about the nature and implications of planetary energy sources and about the geomagnetic field. But more importantly, the subject can help to bring into focus the importance of discussing, debating, and challenging current thinking in a variety of areas.

  4. Reactor containment research and development

    Energy Technology Data Exchange (ETDEWEB)

    Weil, N. A.

    1963-06-15

    An outline is given of containment concepts, sources and release rates of energy, responses of containment structures, effects of projectiles, and leakage rates of radioisotopes, with particular regard to major reactor accidents. (T.F.H.)

  5. Reactor operation environmental information document

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, L.R.; Hayes, D.W.; Hunter, C.H.; Marter, W.L.; Moyer, R.A.

    1989-12-01

    This volume is a reactor operation environmental information document for the Savannah River Plant. Topics include meteorology, surface hydrology, transport, environmental impacts, and radiation effects. 48 figs., 56 tabs. (KD)

  6. Advanced Catalytic Hydrogenation Retrofit Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Reinaldo M. Machado

    2002-08-15

    Industrial hydrogenation is often performed using a slurry catalyst in large stirred-tank reactors. These systems are inherently problematic in a number of areas, including industrial hygiene, process safety, environmental contamination, waste production, process operability and productivity. This program proposed the development of a practical replacement for the slurry catalysts using a novel fixed-bed monolith catalyst reactor, which could be retrofitted onto an existing stirred-tank reactor and would mitigate many of the minitations and problems associated with slurry catalysts. The full retrofit monolith system, consisting of a recirculation pump, gas/liquid ejector and monolith catalyst, is described as a monolith loop reactor or MLR. The MLR technology can reduce waste and increase raw material efficiency, which reduces the overall energy required to produce specialty and fine chemicals.

  7. Unique features of space reactors

    Science.gov (United States)

    Buden, David

    Space reactors are designed to meet a unique set of requirements; they must be sufficiently compact to be launched in a rocket to their operational location, operate for many years without maintenance and servicing, operate in extreme environments, and reject heat by radiation to space. To meet these restrictions, operating temperatures are much greater than in terrestrial power plants, and the reactors tend to have a fast neutron spectrum. Currently, a new generation of space reactor power plants is being developed. The major effort is in the SP-100 program, where the power plant is being designed for seven years of full power, and no maintenance operation at a reactor outlet operating temperature of 1350 K.

  8. Jules Horowitz Reactor, basic design

    Energy Technology Data Exchange (ETDEWEB)

    Bergamaschi, Y.; Bouilloux, Y.; Chantoin, P.; Guigon, B.; Bravo, X.; Germain, C.; Rommens, M.; Tremodeux, P

    2003-07-01

    Since the shutdown of the SILOE reactor in 1997, the OSIRIS reactor has ensured the needs regarding technological irradiation at CEA including those of its industrial partners and customers. The Jules Horowitz Reactor will replace it. It has the ambition to provide the necessary nuclear data and maintain a fission research capacity in Europe after 2010. This capacity should be service-oriented. It will be established in Cadarache. The Jules Horowitz reactor will also: - represent a significant step in term of performances and experimental capabilities, - be designed with a high flexibility, in order to satisfy the current demand from European industry, research and be able to accommodate future requirements, - reach a high level of safety, according to the best current practice. This paper will present the main functionalities and the design options resulting from the 'preliminary design' studies. (authors)

  9. Solid State Reactor Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mays, G.T.

    2004-03-10

    The Solid State Reactor (SSR) is an advanced reactor concept designed to take advantage of Oak Ridge National Laboratory's (ORNL's) recently developed graphite foam that has enhanced heat transfer characteristics and excellent high-temperature mechanical properties, to provide an inherently safe, self-regulated, source of heat for power and other potential applications. This work was funded by the U.S. Department of Energy's Nuclear Energy Research Initiative (NERI) program (Project No. 99-064) from August 1999 through September 30, 2002. The initial concept of utilizing the graphite foam as a basis for developing an advanced reactor concept envisioned that a suite of reactor configurations and power levels could be developed for several different applications. The initial focus was looking at the reactor as a heat source that was scalable, independent of any heat removal/power conversion process. These applications might include conventional power generation, isotope production and destruction (actinides), and hydrogen production. Having conducted the initial research on the graphite foam and having performed the scoping parametric analyses from neutronics and thermal-hydraulic perspectives, it was necessary to focus on a particular application that would (1) demonstrate the viability of the overall concept and (2) require a reasonably structured design analysis process that would synthesize those important parameters that influence the concept the most as part of a feasible, working reactor system. Thus, the application targeted for this concept was supplying power for remote/harsh environments and a design that was easily deployable, simplistic from an operational standpoint, and utilized the new graphite foam. Specifically, a 500-kW(t) reactor concept was pursued that is naturally load following, inherently safe, optimized via neutronic studies to achieve near-zero reactivity change with burnup, and proliferation resistant. These four major areas

  10. Reactor antineutrinos and nuclear physics

    Science.gov (United States)

    Balantekin, A. B.

    2016-11-01

    Short-baseline reactor neutrino experiments successfully measured the neutrino parameters they set out to measure, but they also identified a shape distortion in the 5-7 MeV range as well as a reduction from the predicted value of the flux. Nuclear physics input into the calculations of reactor antineutrino spectra needs to be better refined if this anomaly is to be interpreted as due to sterile neutrino states.

  11. Microchannel Reactors for ISRU Applications

    Science.gov (United States)

    Carranza, Susana; Makel, Darby B.; Blizman, Brandon; Ward, Benjamin J.

    2005-02-01

    Affordable planning and execution of prolonged manned space missions depend upon the utilization of local resources and the waste products which are formed in manned spacecraft and surface bases. Successful in-situ resources utilization (ISRU) will require component technologies which provide optimal size, weight, volume, and power efficiency. Microchannel reactors enable the efficient chemical processing of in situ resources. The reactors can be designed for the processes that generate the most benefit for each mission. For instance, propellants (methane) can be produced from carbon dioxide from the Mars atmosphere using the Sabatier reaction and ethylene can be produced from the partial oxidation of methane. A system that synthesizes ethylene could be the precursor for systems to synthesize ethanol and polyethylene. Ethanol can be used as a nutrient for Astrobiology experiments, as well as the production of nutrients for human crew (e.g. sugars). Polyethylene can be used in the construction of habitats, tools, and replacement parts. This paper will present recent developments in miniature chemical reactors using advanced Micro Electro Mechanical Systems (MEMS) and microchannel technology to support ISRU of Mars and lunar missions. Among other applications, the technology has been demonstrated for the Sabatier process and for the partial oxidation of methane. Microchannel reactors were developed based on ceramic substrates as well as metal substrates. In both types of reactors, multiple layers coated with catalytic material are bonded, forming a monolithic structure. Such reactors are readily scalable with the incorporation of extra layers. In addition, this reactor structure minimizes pressure drop and catalyst settling, which are common problems in conventional packed bed reactors.

  12. The resonance absorption controlled reactor

    Energy Technology Data Exchange (ETDEWEB)

    Caro, R.

    1977-07-01

    In this report a new method of reactor control based on tho isotopic moderator composition variation is studied, taking as a reference a D{sub 2}O/H{sub 2}O system. With this method an spectacular increment in the burn-up degree and a sensible reduction of the conventional control system is obtained. An important part of this work has been the detailed analysis of the parameters affecting the neutron spectrum in a heterogeneous reactor. (Author) 50 refs.

  13. Calculation of reactor antineutrino spectra in TEXONO

    CERN Document Server

    Chen Dong Liang; Mao Ze Pu; Wong, T H

    2002-01-01

    In the low energy reactor antineutrino physics experiments, either for the researches of antineutrino oscillation and antineutrino reactions, or for the measurement of abnormal magnetic moment of antineutrino, the flux and the spectra of reactor antineutrino must be described accurately. The method of calculation of reactor antineutrino spectra was discussed in detail. Furthermore, based on the actual circumstances of NP2 reactors and the arrangement of detectors, the flux and the spectra of reactor antineutrino in TEXONO were worked out

  14. LMFBR type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Iwashige, Kengo

    1996-06-21

    In an LMFBR type reactor, partitions are disposed to a coolant channel at positions lower than the free liquid level, and the width of the partitions is adapted to have a predetermined condition. Namely, when low temperature fluid overflowing the wall of the coolant channel, flows down and collided against the free liquid surface in the coolant channel, since the dropping speed thereof is reduced abruptly, large pressure waves are caused by kinetic force of the low temperature fluid. However, if appropriate numbers of partitions having an appropriate shape are formed, the dropping speed of the low temperature fluid is moderated to reduce the pressure waves. In addition, since the pressure waves are dispersed to the circumferential and lateral directions of the coolant flow channel respectively, the propagation of the pressure waves can be prevented effectively. Further, when the flow of the low temperature fluid is changed to the circumferential direction, for example, by earthquakes, since the partitions act as members resisting against the circumferential change of the low temperature fluid, the change of the direction can be suppressed. (N.H.)

  15. Reactor Simulator Testing

    Science.gov (United States)

    Schoenfeld, Michael P.; Webster, Kenny L.; Pearson, Boise J.

    2013-01-01

    As part of the Nuclear Systems Office Fission Surface Power Technology Demonstration Unit (TDU) project, a reactor simulator test loop (RxSim) was design & built to perform integrated testing of the TDU components. In particular, the objectives of RxSim testing was to verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. In addition, it was decided to include a thermal test of a cold trap purification design and a pump performance test at pump voltages up to 150 V since the targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V. This paper summarizes RxSim testing. The gas and vacuum ground support test equipment performed effectively in NaK fill, loop pressurization, and NaK drain operations. The instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. The cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. The annular linear induction pump (ALIP) tested was able to produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

  16. Novel Catalytic Membrane Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Stuart Nemser, PhD

    2010-10-01

    There are many industrial catalytic organic reversible reactions with amines or alcohols that have water as one of the products. Many of these reactions are homogeneously catalyzed. In all cases removal of water facilitates the reaction and produces more of the desired chemical product. By shifting the reaction to right we produce more chemical product with little or no additional capital investment. Many of these reactions can also relate to bioprocesses. Given the large number of water-organic compound separations achievable and the ability of the Compact Membrane Systems, Inc. (CMS) perfluoro membranes to withstand these harsh operating conditions, this is an ideal demonstration system for the water-of-reaction removal using a membrane reactor. Enhanced reaction synthesis is consistent with the DOE objective to lower the energy intensity of U.S. industry 25% by 2017 in accord with the Energy Policy Act of 2005 and to improve the United States manufacturing competitiveness. The objective of this program is to develop the platform technology for enhancing homogeneous catalytic chemical syntheses.

  17. Tritium management in fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Galloway, T.R.

    1978-05-01

    This is a review paper covering the key environmental and safety issues and how they have been handled in the various magnetic and inertial confinement concepts and reference designs. The issues treated include: tritium accident analyses, tritium process control, occupational safety, HTO formation rate from the gas-phase, disposal of tritium contaminated wastes, and environmental impact--each covering the Joint European Tokamak (J.E.T. experiment), Tokamak Fusion Test Reactor (TFTR), Russian T-20, The Next Step (TNS) designs by Westinghouse/ORNL and General Atomic/ANL, the ANL and ORNL EPR's, the G.A. Doublet Demonstration Reactor, the Italian Fintor-D and the ORNL Demo Studies. There are also the following full scale plant reference designs: UWMAK-III, LASL's Theta Pinch Reactor Design (RTPR), Mirror Fusion Reactor (MFR), Tandem Mirror Reactor (TMR), and the Mirror Hybrid Reactor (MHR). There are four laser device breakeven experiments, SHIVA-NOVA, LLL reference designs, ORNL Laser Fusion power plant, the German ''Saturn,'' and LLL's Laser Fusion EPR I and II.

  18. Irradiation characteristics of laser quads on cylindrical hohlraum wall in indirect-drive facility%激光间接驱动柱形腔壁辐照特性

    Institute of Scientific and Technical Information of China (English)

    侯鹏程; 钟哲强; 文萍; 张彬

    2016-01-01

    在惯性约束聚变间接驱动装置中,针对柱形腔两端注入结构及其光路排布方案,建立了基于束匀滑技术的激光束传输模型.在此基础上,分析了激光集束在真空柱形腔腔壁上的辐照特性,并根据柱形腔整体腔壁光斑排布特性,对激光集束光路排布进行了初步优化.结果表明,随着入射角度的增加,激光集束在腔壁的光斑尺寸逐渐变小,而其在腔壁上的热斑比例无明显变化,偏振特性也基本保持一致.通过进一步分析所有激光集束在腔壁上的强度分布和热斑比例可知,内、外环激光集束在腔壁上的交叠区域将增大局部峰值强度,提高热斑比例.可以通过适当调节内环激光集束的焦面位置和入射角度来改善所有激光集束在腔壁上的辐照特性.%In indirect-drive inertial confinement fusion facilities, aimed at the cylindrical hohlraum with two cones of laser quads and the laser quads configuration, the propagation model of laser quads in the cylindrical hohlraum was built up based on the beam smoothing schemes. On the basis, the irradiation characteristics of laser quads on vacuum cylindrical hohlraum wall were analyzed, and the laser quads arrangement was optimized preliminarily according to all the spots arrangement on hohlraum wall. Results indicate that, with the increasing of the incident angle of laser quads, the spot size of laser quads on hohlraum wall decreases, while the fractional hot spot has no significant change, and the polarization characteristics also remain almost unchanged. By further analysis of the intensity distribution and fractional hot spot of all the laser quads on hohlraum wall, it indicates that the overlap of the inner and outer cones on the hohlraum wall increases the peak intensity and raises the proportion of the hot spot in relevant area. By appropriate adjustment of the location of the focal plane and the incident angle of the inner cone laser quads, the irradiation

  19. Long-term effect of quad helix expansion of dental arch*☆%四圈簧扩大牙弓的长期效果*☆

    Institute of Scientific and Technical Information of China (English)

    王峰; 陆怀秀; 林松杉

    2013-01-01

      背景:快速扩大牙弓是快速扩大颌骨的有效方法,而与快速扩展相比,缓慢扩展稳定性更高,复发更少,但四圈簧扩弓的长期稳定性少见报道。目的:回顾性分析正畸临床中四圈簧扩大牙弓的临床效果。方法:混合牙列期及恒牙列早期牙弓狭窄患者22例使用四圈簧扩大牙弓至少3 mm,在扩大牙弓之前(T1期)、Ⅰ期四圈簧扩弓治疗完成或整个治疗结束(T2期)及治疗完成后2年(T3期)分别制取牙齿石膏研究模型并摄取头颅后前位片,在模型上测量两侧第一恒磨牙之间距离,在后前位片上描点(J 点)测量两侧基骨间距离及磨牙倾斜度,评价牙弓扩大的矫正及矫形效果。结果与结论:与扩弓前相比,四圈簧扩弓治疗后患者第一恒磨牙倾斜度和两侧基骨间距离逐渐减小;而四圈簧扩弓治疗后相比,随访2年时,患者两侧第一恒磨牙间距离、第一恒磨牙倾斜度和两侧基骨间距离的差异无显著性意义(P >0.05),提示四圈簧扩大牙弓的长期效果是稳定的,并有矫形效果。%BACKGROUND: Rapid expansion of the dental arch is an effective way to rapidly expanse the jaw. Compared with rapid expansion, the slow expansion has higher stability and less recurrence, but the reports on the long-term stability of quad helix expansion are rare. OBJECTIVE: To retrospectively analyze the clinical effect of quad helix expansion in orthodontics. METHODS: Twenty-two subjects with dental arch stenosis in mixed dentition and early permanent dentition who experienced an expansion of at least 3 mm with quad helix appliance were selected for this study. Plaster dental casts and posteroanterior radiographs were evaluated at the beginning of the treatment (T1), at the completion of phase I quad helix expansion or ful treatment (T2), and approximately 2 years fol owing the completion of treatment (T3). The distance between two first molars was

  20. Innovative hybrid biological reactors using membranes; Reactores biologico hibrido innovadores utilizando membranas

    Energy Technology Data Exchange (ETDEWEB)

    Diez, R.; Esteban-Garcia, A. L.; Florio, L. de; Rodriguez-Hernandez, L.; Tejero, I.

    2011-07-01

    In this paper we present two lines of research on hybrid reactors including the use of membranes, although with different functions: RBPM, biofilm reactors and membranes filtration RBSOM, supported biofilm reactors and oxygen membranes. (Author) 14 refs.

  1. Establishment of licensing process for development reactors

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Jong Chull; Yune, Young Gill; Kim, Woong Sik (and others)

    2006-02-15

    A study on licensing processes for development reactors has been performed to prepare the licensing of development reactors developed in Korea. The contents and results of the study are summarized as follows. The licensing processes for nuclear reactors in Korea, U.S.A., Japan, France, U.K., Canada, and IAEA were surveyed and analyzed to obtain technical bases necessary for establishing licensing processes applicable to development reactors in Korea. Based on the technical bases obtained the above analysis, the purpose, power output, and design characteristics of development reactors were analyzed in detail. The analysis results suggested that development reactors should be classified as a new reactor category (called as 'development reactor') separated from the current reactor categories such as the research reactor and the power reactor. Therefore, it is proposed to establish a new reactor category classified as 'development reactor' for the development reactors. And licensing processes, including licensing technical requirements, licensing document requirements, and other regulatory requirements, were also proposed for the development reactors. In order to institutionalize the licensing processes developed in this study, it is necessary to revise the current laws. Therefore, draft provisions of Atomic Energy Act, Enforcement Decree of the Atomic Energy Act, and Enforcement Regulation of the Atomic Energy Act have been developed for the preparation of the future legalization of the licensing processes proposed for the development reactors. Conclusively, a proposal of licensing processes and draft provisions of laws have been developed for the development reactors. The results proposed in this study can be applied directly to the licensing of the future development reactors. Furthermore, they will also contribute to establishing successfully the licensing processes of the development reactors.

  2. Repairing liner of the reactor; Reparacion del liner del reactor

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar H, F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2001-07-15

    Due to the corrosion problems of the aluminum coating of the reactor pool, a periodic inspections program by ultrasound to evaluate the advance grade and the corrosion speed was settled down. This inspections have shown the necessity to repair some areas, in those that the slimming is significant, of not making it can arrive to the water escape of the reactor pool. The objective of the repair is to place patches of plates of 1/4 inch aluminum thickness in the areas of the reactor 'liner', in those that it has been detected by ultrasound a smaller thickness or similar to 3 mm. To carry out this the fuels are move (of the core and those that are decaying) to a temporary storage, the structure of the core is confined in a tank that this placed inside the pool of the reactor, a shield is placed in the thermal column and it is completely extracted the water for to leave uncover the 'liner' of the reactor. (Author)

  3. 微型四轴飞行器的设计与实现%Design and implementation of mini quad-rotors aircraft

    Institute of Scientific and Technical Information of China (English)

    薛鹏; 任鹏飞; 曹学儒; 马壮

    2016-01-01

    The quad-rotor mini rotorcraft is an under actuated system,which is powered by adjusting the speed of the motors. In order to discuss the problem of quad-rotor aircraft control,the preliminary design of the control system was proposed. The hardware of flight control system was designed based on single chip microcontroller STM32 and sensor MPU6050. The key points include driven cir-cuit,sensors and communication module. Based on PID control scheme,the software was fulfilled. As its core part,quaternion num-bers and Kalman filtering were adopted to obtain exact values of the attitude angles. Simulation and indoor tests results shown that the designed hardware system is reliable and can meet requirements. Some meaningful experiences to the design of quad-rotor aircraft are introduced.%四轴飞行器是通过调节电机转速来控制运动姿态的典型欠驱动系统,为研究飞行器的姿态控制问题,对飞行控制系统进行了初步设计。硬件部分以STM32单片机为主控芯片,采用MPU6050陀螺仪传感器完成飞行控制系统的选型设计,重点讨论了驱动电路、传感器和通信模块的选型设计。软件部分以PID控制为基础,重点介绍了姿态角检测过程中的四元数变换和卡尔曼滤波环节,这两个步骤保障了所得姿态角的准确性。仿真分析和室内测试显示,该硬件设计性能可靠,其姿态角控制达到了预期效果,对四轴飞行器的设计有借鉴意义。

  4. Thermal calculation method for quad-sectional regenerative air preheater%四分仓回转式空气预热器热力计算方法

    Institute of Scientific and Technical Information of China (English)

    陈昌贤; 孙奉仲; 李飞; 吴艳艳

    2014-01-01

    A new thermal calculation model for quad-sectional regenerative air preheater was investigated based on the analysis of operating mode and heat transfer characteristics of quad-sectional air preheaters.The model included two cal-culating steps:the average outlet flue gas temperature and the weighted average outlet air temperature were obtained through the first step calculation;and based on the first step calculation results, the average outlet air temperatures were obtained in right-secondary airside, primary air side and left-secondary airside respectively by the second step calcula-tion.The results showed that the maximum and minimum relative deviations between calculated values and design val-ues were 2.27% and 0.21% respectively.For a 300 MW circulating fluidized bed boiler unit with quad-sectional air preheater, the maximum and average relative deviations between calculated values and actual operation data were 4%and 1.8%respectively, the accuracy and reliability of this thermal calculation model were verified.%基于四分仓空气预热器的运行方式和传热特点的分析,建立了先合仓再分仓的热力计算模型。模型包含合仓和分仓两步计算,通过合仓计算获得平均出口烟温和有加权的平均出口风温;利用合仓计算结果进行分仓计算,获得右二次风仓、一次风仓和左二次风仓的平均出口风温。结果表明,计算值与设计值的最大相对偏差为2.27%,最小相对偏差为0.21%。以某300 MW循环流化床锅炉机组的四分仓空气预热器为实例,在4个常用工况下,计算值与实际运行数据的最大相对偏差为4%,平均相对偏差为1.8%,验证了此计算方法的准确性和可靠性。

  5. Reactor Simulator Testing

    Science.gov (United States)

    Schoenfeld, Michael P.; Webster, Kenny L.; Pearson, Boise Jon

    2013-01-01

    As part of the Nuclear Systems Office Fission Surface Power Technology Demonstration Unit (TDU) project, a reactor simulator test loop (RxSim) was design & built to perform integrated testing of the TDU components. In particular, the objectives of RxSim testing was to verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. In addition, it was decided to include a thermal test of a cold trap purification design and a pump performance test at pump voltages up to 150 V since the targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V. This paper summarizes RxSim testing. The gas and vacuum ground support test equipment performed effectively in NaK fill, loop pressurization, and NaK drain operations. The instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. The cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. The annular linear induction pump (ALIP) tested was able to produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz. Keywords: fission, space power, nuclear, liquid metal, NaK.

  6. Reactivity determination in accelerator driven reactors using reactor noise analysis

    Directory of Open Access Journals (Sweden)

    Kostić Ljiljana 1

    2002-01-01

    Full Text Available Feynman-alpha and Rossi-alpha methods are used in traditional nuclear reactors to determine the subcritical reactivity of a system. The methods are based on the measurement of the mean value, variance and the covariance of detector counts for different measurement times. Such methods attracted renewed attention recently with the advent of the so-called accelerator driven reactors (ADS proposed some time ago. The ADS systems, intended to be used either in energy generation or transuranium transmutation, will use a subcritical core with a strong spallation source. A spallation source has statistical properties that are different from those traditionally used by radioactive sources. In such reactors the monitoring of the subcritical reactivity is very important, and a statistical method, such as the Feynman-alpha method, is capable of resolving this problem.

  7. QUAD FAMILY CENTERING.

    Energy Technology Data Exchange (ETDEWEB)

    PINAYEV, I.

    2005-11-01

    It is well known that beam position monitors (BPM) utilizing signals from pickup electrodes (PUE) provide good resolution and relative accuracy. The absolute accuracy (i.e. position of the orbit in the vacuum chamber) is not very good due to the various reasons. To overcome the limitation it was suggested to use magnetic centers of quadrupoles for the calibration of the BPM [1]. The proposed method provides accuracy better then 200 microns for centering of the beam position monitors using modulation of the whole quadrupole family.

  8. 2013 FEMA Quad Index

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — The National Flood Hazard Layer (NFHL) data incorporates all Digital Flood Insurance Rate Map(DFIRM) databases published by FEMA, and any Letters Of Map Revision...

  9. QUAD4 Seminar. Revision

    Science.gov (United States)

    1993-04-01

    OR jANIZATION (If applicable) Flight Dynamics Laboratory JWRDC/ FIBRA N/A Bc. ADDRESS (City, State, and ZIP Code) 10 SOURCE OF FUNDING NUMBERS 0...wish to be removed from our mailing list, or if the addressee is no longer employed by your organization please notify W RDC/ FIBRA . WPAFB, OH 45433

  10. Thermonuclear Reflect AB-Reactor

    CERN Document Server

    Bolonkin, Alexander

    2008-01-01

    The author offers a new kind of thermonuclear reflect reactor. The remarkable feature of this new reactor is a three net AB reflector, which confines the high temperature plasma. The plasma loses part of its energy when it contacts with the net but this loss can be compensated by an additional permanent plasma heating. When the plasma is rarefied (has a small density), the heat flow to the AB reflector is not large and the temperature in the triple reflector net is lower than 2000 - 3000 K. This offered AB-reactor has significantly less power then the currently contemplated power reactors with magnetic or inertial confinement (hundreds-thousands of kW, not millions of kW). But it is enough for many vehicles and ships and particularly valuable for tunnelers, subs and space apparatus, where air to burn chemical fuel is at a premium or simply not available. The author has made a number of innovations in this reactor, researched its theory, developed methods of computation, made a sample computation of typical pr...

  11. Heterogeneous Transmutation Sodium Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    S. E. Bays

    2007-09-01

    The threshold-fission (fertile) nature of Am-241 is used to destroy this minor actinide by capitalizing upon neutron capture instead of fission within a sodium fast reactor. This neutron-capture and its subsequent decay chain leads to the breeding of even neutron number plutonium isotopes. A slightly moderated target design is proposed for breeding plutonium in an axial blanket located above the active “fast reactor” driver fuel region. A parametric study on the core height and fuel pin diameter-to-pitch ratio is used to explore the reactor and fuel cycle aspects of this design. This study resulted in both non-flattened and flattened core geometries. Both of these designs demonstrated a high capacity for removing americium from the fuel cycle. A reactivity coefficient analysis revealed that this heterogeneous design will have comparable safety aspects to a homogeneous reactor of comparable size. A mass balance analysis revealed that the heterogeneous design may reduce the number of fast reactors needed to close the current once-through light water reactor fuel cycle.

  12. Entropy Production in Chemical Reactors

    Science.gov (United States)

    Kingston, Diego; Razzitte, Adrián C.

    2017-06-01

    We have analyzed entropy production in chemically reacting systems and extended previous results to the two limiting cases of ideal reactors, namely continuous stirred tank reactor (CSTR) and plug flow reactor (PFR). We have found upper and lower bounds for the entropy production in isothermal systems and given expressions for non-isothermal operation and analyzed the influence of pressure and temperature in entropy generation minimization in reactors with a fixed volume and production. We also give a graphical picture of entropy production in chemical reactions subject to constant volume, which allows us to easily assess different options. We show that by dividing a reactor into two smaller ones, operating at different temperatures, the entropy production is lowered, going as near as 48 % less in the case of a CSTR and PFR in series, and reaching 58 % with two CSTR. Finally, we study the optimal pressure and temperature for a single isothermal PFR, taking into account the irreversibility introduced by a compressor and a heat exchanger, decreasing the entropy generation by as much as 30 %.

  13. Simplifying Microbial Electrosynthesis Reactor Design

    Directory of Open Access Journals (Sweden)

    Cloelle G.S. Giddings

    2015-05-01

    Full Text Available Microbial electrosynthesis, an artificial form of photosynthesis, can efficiently convert carbon dioxide into organic commodities; however, this process has only previously been demonstrated in reactors that have features likely to be a barrier to scale-up. Therefore, the possibility of simplifying reactor design by both eliminating potentiostatic control of the cathode and removing the membrane separating the anode and cathode was investigated with biofilms of Sporomusa ovata, which reduces carbon dioxide to acetate. In traditional ‘H-cell’ reactors, where the anode and cathode chambers were separated with a proton-selective membrane, the rates and columbic efficiencies of microbial electrosynthesis remained high when electron delivery at the cathode was powered with a direct current power source rather than with a poteniostat-poised cathode utilized in previous studies. A membrane-less reactor with a direct-current power source with the cathode and anode positioned to avoid oxygen exposure at the cathode, retained high rates of acetate production as well as high columbic and energetic efficiencies. The finding that microbial electrosynthesis is feasible without a membrane separating the anode from the cathode, coupled with a direct current power source supplying the energy for electron delivery, is expected to greatly simplify future reactor design and lower construction costs.

  14. Hanford reactor and separations facility advantages

    Energy Technology Data Exchange (ETDEWEB)

    1963-06-27

    This document describes the advantages and limitations of Hanford production facilities. In addition to summarizing the technical parameters of the reactors and separations plants and their mechanical features, the unique aspects of these facilities to the production of special materials in which the Commission may be interested have been discussed. As the primary difference between the B-C-D-DR-F-H reactors and the K reactors and the K reactors is in the number and length of process channels. This report is addressed primarily to the 2000-tube reactors. K reactor characteristics are within the range of lattice and flexibility parameters described.

  15. Imaging Fukushima Daiichi reactors with muons

    Directory of Open Access Journals (Sweden)

    Haruo Miyadera

    2013-05-01

    Full Text Available A study of imaging the Fukushima Daiichi reactors with cosmic-ray muons to assess the damage to the reactors is presented. Muon scattering imaging has high sensitivity for detecting uranium fuel and debris even through thick concrete walls and a reactor pressure vessel. Technical demonstrations using a reactor mockup, detector radiation test at Fukushima Daiichi, and simulation studies have been carried out. These studies establish feasibility for the reactor imaging. A few months of measurement will reveal the spatial distribution of the reactor fuel. The muon scattering technique would be the best and probably the only way for Fukushima Daiichi to make this determination in the near future.

  16. Fast breeder reactors an engineering introduction

    CERN Document Server

    Judd, A M

    1981-01-01

    Fast Breeder Reactors: An Engineering Introduction is an introductory text to fast breeder reactors and covers topics ranging from reactor physics and design to engineering and safety considerations. Reactor fuels, coolant circuits, steam plants, and control systems are also discussed. This book is comprised of five chapters and opens with a brief summary of the history of fast reactors, with emphasis on international and the prospect of making accessible enormous reserves of energy. The next chapter deals with the physics of fast reactors and considers calculation methods, flux distribution,

  17. Space shuttle engineering and operations support. Isolation between the S-band quad antenna and the S-band payload antenna. Engineering systems analysis

    Science.gov (United States)

    Lindsey, J. F.

    1976-01-01

    The isolation between the upper S-band quad antenna and the S-band payload antenna on the shuttle orbiter is calculated using a combination of plane surface and curved surface theories along with worst case values. A minimum value of 60 db isolation is predicted based on recent antenna pattern data, antenna locations on the orbiter, curvature effects, dielectric covering effects and edge effects of the payload bay. The calculated value of 60 db is significantly greater than the baseline value of 40 db. Use of the new value will result in the design of smaller, lighter weight and less expensive filters for S-band transponder and the S-band payload interrogator.

  18. A Magnetohydrodynamic Model of The M87 Jet. II. Self-consistent Quad-shock Jet Model for Optical Relativistic Motions and Particle Acceleration

    CERN Document Server

    Nakamura, Masanori

    2014-01-01

    We describe a new paradigm for understanding both relativistic motions and particle acceleration in the M87 jet: a magnetically dominated relativistic flow that naturally produces four relativistic magnetohydrodynamic (MHD) shocks (forward/reverse fast and slow modes). We apply this model to a set of optical super- and subluminal motions discovered by Biretta and coworkers with the {\\em Hubble Space Telescope} during 1994 -- 1998. The model concept consists of ejection of a {\\em single} relativistic Poynting jet, which possesses a coherent helical (poloidal + toroidal) magnetic component, at the remarkably flaring point HST-1. We are able to reproduce quantitatively proper motions of components seen in the {\\em optical} observations of HST-1 with the same model we used previously to describe similar features in radio VLBI observations in 2005 -- 2006. This indicates that the quad relativistic MHD shock model can be applied generally to recurring pairs of super/subluminal knots ejected from the upstream edge o...

  19. Elvitegravir/cobicistat/emtricitabine/tenofovir DF (Quad has durable efficacy and differentiated safety compared to efavirenz/emtricitabine/tenofovir DF at week 96 in treatment-naïve HIV-1-infected patients

    Directory of Open Access Journals (Sweden)

    J Szwarcberg

    2012-11-01

    Full Text Available Purpose of the study: The primary Week 48 analysis of this ongoing, randomized, double-blind, double-dummy, active-controlled Phase 3 trial of elvitegravir/cobicistat/emtricitabine/tenofovir DF (Quad in treatment-naïve patients demonstrated that Quad was non-inferior to efavirenz/emtricitabine/tenofovir DF (EFV/FTC/TDF with a differentiated safety profile. We report the Week 96 interim data. Methods: Key eligibility criteria included HIV-1 RNA ≥5,000 c/mL and eGFR ≥70 mL/min. Virologic success (HIV-1 RNA <50 c/mL at Week 96 was assessed per snapshot algorithm. Adverse events and laboratory data were collected prospectively. Results: 700 patients (89% male, 63% white, 33% with HIV-1 RNA >100,000 c/mL were randomized and treated. At Week 48, Quad was non-inferior to EFV/FTC/TDF (88% vs 84%, difference +3.6%, 95% CI -1.6% to 8.8%. High rates of virologic success were maintained at Week 96 (84% vs 82%, difference 2.7%, 95% CI -2.9% to 8.3%. Subgroup analysis revealed similar rates of virologic success in patients with baseline HIV-1 RNA >100,000 c/mL (81% vs 83%. Mean CD4 cell increase (cells/mm3 was 295 vs 273. Emergent resistance was infrequent (3% vs 3%. Rates of study drug discontinuation due to adverse events (AEs were low and comparable (5% vs 7%. Rates of neuropsychiatric AEs were lower in Quad than in EFV/FTC/TDF (47% vs 66%, P<0.001, as were rates of rash (21% vs 31%, P=0.006. Drug discontinuation due to renal reasons occurred in 7 (2% vs 0 patients through Week 96; only two patients discontinued Quad since Week 48 due to serum creatinine (Cr increase without features of proximal renal tubulopathy. Median changes in serum Cr (µmol/L [mg/dL] at Week 96 in Quad vs EFV/FTC/TDF (11.5 vs 0.9 [0.13 vs 0.01] were similar to those at Week 48 (12.4 vs 0.9 [0.14 vs 0.01]. Quad had smaller median increases (mmol/L [mg/dL] in total (0.23 vs 0.47 [9 vs 18], P<0.001 and LDL cholesterol (0.23 vs 0.41 [9 vs16], P=0.011, and similar increase in

  20. Elvitegravir/cobicistat/emtricitabine/tenofovir DF (Quad has durable efficacy and differentiated safety compared to atazanavir boosted by ritonavir plus emtricitabine/tenofovir DF at week 96 in treatment-naïve HIV-1-infected patients

    Directory of Open Access Journals (Sweden)

    M Rhee

    2012-11-01

    Full Text Available Purpose of the study: The primary Week 48 analysis of this ongoing, randomized, double-blind, double-dummy, active-controlled Phase 3 international trial of elvitegravir/cobicistat/emtricitabine/tenofovir DF (Quad in treatment-naïve patients demonstrated that Quad was non-inferior to atazanavir boosted by ritonavir (ATV/r + FTC/TDF with a differentiated safety profile. We report the Week 96 interim data. Methods: Key eligibility criteria included HIV-1 RNA≥5,000 c/mL and eGFR≥70 mL/min. Virologic success (HIV-1 RNA <50 c/mL at Week 96 was assessed per snapshot algorithm. Adverse events and laboratory data were collected prospectively. Bone mineral density (BMD was assessed by DEXA scan in a subgroup of patients. Results: 708 patients (90% male, 74% white, 41% with HIV-1 RNA >100,000 c/mL were randomized and treated. At Week 48, Quad was non-inferior to ATV/r+FTC/TDF (90% vs 87%, difference 3.0%, 95% CI −1.9% to 7.8%. High rates of virologic success were maintained at Week 96 (83% vs 82%, difference 1.1%, 95% CI −4.5% to 6.7%. Subgroup analysis revealed similar rates of virologic success in patients with baseline HIV-1 RNA >100,000 c/mL (82% vs 80%. Mean CD4 cell increases (cells/mm3 were 256 vs 261 at Week 96. Emergent resistance was infrequent (2% vs<1%. Rates of study drug discontinuation due to adverse events (AEs were low and comparable (4% vs 6%. Rates of study drug discontinuation due to renal reasons remained low and similar through Week 96 (3 [0.8%] vs 2 [0.6%]; since Week 48, 1 patient in each group discontinued study drug due to serum creatinine (Cr increase without features of proximal renal tubulopathy. Median increases from baseline in serum Cr (µmol/L [mg/dL] in Quad vs ATV/r+FTC/TDF at Week 96 (10.6 vs 7.1 [0.12 vs 0.08] were similar to those at Week 48 (10.6 vs 7.1 [0.12 vs 0.08]. Quad continued to have smaller increases (mmol/L [mg/dL] in triglycerides (0.06 vs 0.18 [5 vs 16], P=0.012; Quad had greater increases in

  1. Estimate of Precipitation from the Dual-Beam Airborne Radars in TOGA COARE. Part 1: The K-Z Relationships Derived from Stereo and Quad-Beam Analysis.

    Science.gov (United States)

    Oury, Stéphane; Testud, Jacques; Marécal, Virginie

    1999-02-01

    The recent development of dual-beam airborne Doppler weather radar offers the possibility to perform high-resolution observations of the three-dimensional air motion and precipitation fields associated with severe weather systems. However, the limited size of the onboard antennas imposes the use of high radar frequencies (e.g., X band) in order to achieve satisfactory beam resolutions. Therefore, the sampled radar reflectivity is attenuated when intercepting intense rain cells. This paper aims at developing algorithms for correcting the observed radar reflectivity for attenuation that fully exploit the dual-beam sampling strategy and the multiple aircraft operations conducted in Tropical Ocean and Global Atmosphere Coupled Ocean-Atmosphere Response Experiment (TOGA COARE). Its specific contribution is twofold.Algorithm development. On the one hand, the former stereoradar analysis helps to retrieve independently the`true' (nonattenuated) radar reflectivity Z and specific attenuation K when using two radar beams from one aircraft. The algorithm is reformulated in Cartesian coordinates, which greatly improves its flexibility. And on the other hand, a new approach is developed, the quad-beam analysis, which is particularly powerful when processing the data of a two dual-beam aircraft operation focused on the same rain cells.Data analysis. An application of the stereoradar and quad-beam analysis to a TOGA COARE weather system is presented. The corrected Z and K fields are cross validated using different algorithms or datasets for the same event. The radar derived K-Z relationships are also compared with that deduced from in situ microphysical probes sampling using a scattering model. The full three-dimensional description of the Z and K fields is then used to appreciate to what extent the observed heavy rain reached the `equilibrium' described by previous authors in response to droplet coalescence and breakup.

  2. 基于四叉树的嵌入式平台Huffman解码优化%Embedded Platform Huffman Optimization Decoding Algorithm Base on Quad-Tree

    Institute of Scientific and Technical Information of China (English)

    鲁云飞; 何明华

    2012-01-01

    考虑到嵌入式设备资源的有限性,提出一种基于四叉树的Huffman解码优化算法.解码过程中,先将Huffman码表表示成四叉树结构,据此重建为一维数组,并充分利用数值计算代替判断与跳转操作.为测试本算法解码性能,将其应用于嵌入式MP3实时解码中,结果表明本算法内存损耗小,解码速率快,算法复杂度低,相比于其他优化算法,更适合应用于嵌入式设备中.%Considering the limitation of embedded system resources, a Huffman decoding optimization algorithm based on the quad tree is proposed in this paper. In this process, the Huffman code table is expressed as quad tree structure at first, and according to which a one-dimensional array is reconstructed, then make full use of numerical calculation instead of judgment and jump operation. In order to test the decoding performance, the method is applied to the embedded'realtime MP3 decoding. The results show that the algorithm memory loss is small, decoding speed is rapid and its complexity is low, compared to other optimization algorithms, this algorithm is more suitable for application in embedded devices.

  3. A tubular focused sonochemistry reactor

    Institute of Scientific and Technical Information of China (English)

    ZHOU GuangPing; LIANG ZhaoFeng; LI ZhengZhong; ZHANG YiHui

    2007-01-01

    This paper presents a new sonochemistry reactor, which consists of a cylindrical tube with a certain length and piezoelectric transducers at tube's end with the longitudinal vibration. The tube can effectively transform the longitudinal vibration into the radial vibration and thereby generates ultrasound. Furthermore, ultrasound can be focused to form high-intensity ultrasonic field inside tube. The reactor boasts of simple structure and its whole vessel wall can radiate ultrasound so that the electroacoustic transfer efficiency is high. The focused ultrasonic field provides good condition for sonochemical reaction. The length of the reactor can be up to 2 meters, and liquids can pass through it continuously, so it can be widely applied in liquid processing such as sonochemistry.

  4. A compact Tokamak transmutation reactor

    Institute of Scientific and Technical Information of China (English)

    QiuLi-Jian; XiaoBing-Jia

    1997-01-01

    The low aspect ration tokamak is proposed for the driver of a transmutation reactor.The main parameters of the reactor core,neutronic analysis of the blanket are given>the neutron wall loading can be lowered from the magnitude order of 1 MW/m2 to 0.5MW/m2 which is much easier to reach in the near future,and the transmutation efficiency (fission/absorption ratio)is raised further.The blanket power density is about 200MW/m3 which is not difficult to deal with.The key components such as diverter and center conductor post are also designed and compared with conventional TOkamak,Finally,by comparison with the other drivers such as FBR,PWR and accelerator,it can be anticipated that the low aspect ratio transmutation reactor would be one way of fusion energy applications in the near future.

  5. Plasma reactor waste management systems

    Science.gov (United States)

    Ness, Robert O., Jr.; Rindt, John R.; Ness, Sumitra R.

    1992-01-01

    The University of North Dakota is developing a plasma reactor system for use in closed-loop processing that includes biological, materials, manufacturing, and waste processing. Direct-current, high-frequency, or microwave discharges will be used to produce plasmas for the treatment of materials. The plasma reactors offer several advantages over other systems, including low operating temperatures, low operating pressures, mechanical simplicity, and relatively safe operation. Human fecal material, sunflowers, oats, soybeans, and plastic were oxidized in a batch plasma reactor. Over 98 percent of the organic material was converted to gaseous products. The solids were then analyzed and a large amount of water and acid-soluble materials were detected. These materials could possibly be used as nutrients for biological systems.

  6. Investigation of KW reactor incident

    Energy Technology Data Exchange (ETDEWEB)

    Sturges, D G [USAEC Hanford Operations Office, Richland, WA (United States); Hauff, T W; Greager, O H [General Electric Co., Richland, WA (United States). Hanford Atomic Products Operation

    1955-02-11

    The new KW reactor was placed in operation on January 4, 1955, and had been running at relatively low power levels for only 17 hours when it was shut down because of a process tube water leak which appeared to be associated with a slug rupture. After several days of unrewarding effort to remove the slugs and tube by customary methods, it developed that considerable melting of the tube and slugs had taken place. It was then evident that removal of the stuck mass and repairs to the damaged tube channel would require unusual measures that were certain to extend the reactor outage for several weeks. This report documents the work and findings of the Committee which investigated the KW reactor incident. Its content represents unanimous agreement among the three Committee members.

  7. Gaseous fuel nuclear reactor research

    Science.gov (United States)

    Schwenk, F. C.; Thom, K.

    1975-01-01

    Gaseous-fuel nuclear reactors are described; their distinguishing feature is the use of fissile fuels in a gaseous or plasma state, thereby breaking the barrier of temperature imposed by solid-fuel elements. This property creates a reactor heat source that may be able to heat the propellant of a rocket engine to 10,000 or 20,000 K. At this temperature level, gas-core reactors would provide the breakthrough in propulsion needed to open the entire solar system to manned and unmanned spacecraft. The possibility of fuel recycling makes possible efficiencies of up to 65% and nuclear safety at reduced cost, as well as high-thrust propulsion capabilities with specific impulse up to 5000 sec.

  8. Nuclear Reactor Engineering Analysis Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Carlos Chavez-Mercado; Jaime B. Morales-Sandoval; Benjamin E. Zayas-Perez

    1998-12-31

    The Nuclear Reactor Engineering Analysis Laboratory (NREAL) is a sophisticated computer system with state-of-the-art analytical tools and technology for analysis of light water reactors. Multiple application software tools can be activated to carry out different analyses and studies such as nuclear fuel reload evaluation, safety operation margin measurement, transient and severe accident analysis, nuclear reactor instability, operator training, normal and emergency procedures optimization, and human factors engineering studies. An advanced graphic interface, driven through touch-sensitive screens, provides the means to interact with specialized software and nuclear codes. The interface allows the visualization and control of all observable variables in a nuclear power plant (NPP), as well as a selected set of nonobservable or not directly controllable variables from conventional control panels.

  9. Utilisation of thorium in reactors

    Science.gov (United States)

    Anantharaman, K.; Shivakumar, V.; Saha, D.

    2008-12-01

    India's nuclear programme envisages a large-scale utilisation of thorium, as it has limited deposits of uranium but vast deposits of thorium. The large-scale utilisation of thorium requires the adoption of closed fuel cycle. The stable nature of thoria and the radiological issues associated with thoria poses challenges in the adoption of a closed fuel cycle. A thorium fuel based Advanced Heavy Water Reactor (AHWR) is being planned to provide impetus to development of technologies for the closed thorium fuel cycle. Thoria fuel has been loaded in Indian reactors and test irradiations have been carried out with (Th-Pu) MOX fuel. Irradiated thorium assemblies have been reprocessed and the separated 233U fuel has been used for test reactor KAMINI. The paper highlights the Indian experience with the use of thorium and brings out various issues associated with the thorium cycle.

  10. External fuel thermionic reactor system.

    Science.gov (United States)

    Mondt, J. F.; Peelgren, M. L.

    1971-01-01

    Thermionic reactors are prime candidates for nuclear electric propulsion. The national thermionic reactor effort is concentrated on the flashlight concept with the external-fuel concept as the backup. The external-fuel concept is very adaptable to a completely modular power subsystem which is attractive for highly reliable long-life applications. The 20- to 25-cm long, externally-fueled converters have been designed, fabricated, and successfully tested with many thermal cycles by electrical heating. However, difficulties have been encountered during encapsulation for nuclear heated tests and none have been started to date. These nuclear tests are required to demonstrate the concept feasibility.

  11. Analysis of Adiabatic Batch Reactor

    Directory of Open Access Journals (Sweden)

    Erald Gjonaj

    2016-05-01

    Full Text Available A mixture of acetic anhydride is reacted with excess water in an adiabatic batch reactor to form an exothermic reaction. The concentration of acetic anhydride and the temperature inside the adiabatic batch reactor are calculated with an initial temperature of 20°C, an initial temperature of 30°C, and with a cooling jacket maintaining the temperature at a constant of 20°C. The graphs of the three different scenarios show that the highest temperatures will cause the reaction to occur faster.

  12. PITR: Princeton Ignition Test Reactor

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-01

    The principal objectives of the PITR - Princeton Ignition Test Reactor - are to demonstrate the attainment of thermonuclear ignition in deuterium-tritium, and to develop optimal start-up techniques for plasma heating and current induction, in order to determine the most favorable means of reducing the size and cost of tokamak power reactors. This report describes the status of the plasma and engineering design features of the PITR. The PITR geometry is chosen to provide the highest MHD-stable values of beta in a D-shaped plasma, as well as ease of access for remote handling and neutral-beam injection.

  13. Reactor shutdown delays medical procedures

    Science.gov (United States)

    Gwynne, Peter

    2008-01-01

    A longer-than-expected maintenance shutdown of the Canadian nuclear reactor that produces North America's entire supply of molybdenum-99 - from which the radioactive isotopes technetium-99 and iodine-131 are made - caused delays to the diagnosis and treatment of thousands of seriously ill patients last month. Technetium-99 is a key component of nuclear-medicine scans, while iodine-131 is used to treat cancer and other diseases of the thyroid. Production eventually resumed, but only after the Canadian government had overruled the Canadian Nuclear Safety Commission (CNSC), which was still concerned about the reactor's safety.

  14. Fundamentals of Nuclear Reactor Physics

    CERN Document Server

    Lewis, E E

    2008-01-01

    This new streamlined text offers a one-semester treatment of the essentials of how the fission nuclear reactor works, the various approaches to the design of reactors, and their safe and efficient operation. The book includes numerous worked-out examples and end-of-chapter questions to help reinforce the knowledge presented. This textbook offers an engineering-oriented introduction to nuclear physics, with a particular focus on how those physics are put to work in the service of generating nuclear-based power, particularly the importance of neutron reactions and neutron behavior. Engin

  15. Scaledown of a methanol reactor

    Energy Technology Data Exchange (ETDEWEB)

    Berty, J.M.

    1983-07-01

    This article shows how it is possible to define operating conditions for pilot plants and development labs by scaling down a commercial reactor. Points out that scaledown consideration and experiment planning can be done in a similar manner for the boiling water-cooled, Lurgi-type reactor. Explains that although the design of large, single-train plants to produce methanol for fuel use has different economic objectives, product specifications, and technical constraints from the traditional commercial methanol plants, the same fundamental laws of thermodynamics and reaction kinetics apply to both types of operation.

  16. Reactor Antineutrino Signals at Morton and Boulby

    CERN Document Server

    Dye, Steve

    2016-01-01

    Increasing the distance from which an antineutrino detector is capable of monitoring the operation of a registered reactor, or discovering a clandestine reactor, strengthens the Non-Proliferation of Nuclear Weapons Treaty. This report presents calculations of reactor antineutrino interactions, from quasi-elastic neutrino-proton scattering and elastic neutrino-electron scattering, in a water-based detector operated >10 km from a commercial power reactor. It separately calculates signal from the proximal reactor and background from all other registered reactors. The main results are interaction rates and kinetic energy distributions of charged leptons scattered from quasi-elastic and elastic processes. Comparing signal and background distributions evaluates reactor monitoring capability. Scaling the results to detectors of different sizes, target media, and standoff distances is straightforward. Calculations are for two examples of a commercial reactor (P_th~3 GW) operating nearby (L~20 km) an underground facil...

  17. Oregon State University TRIGA Reactor annual report

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.V.; Johnson, A.G.; Bennett, S.L.; Ringle, J.C.

    1979-08-31

    The use of the Oregon State University TRIGA Reactor during the year ending June 30, 1979, is summarized. Environmental and radiation protection data related to reactor operation and effluents are included.

  18. Request for Naval Reactors Comment on Proposed Prometheus Space Flight Nuclear Reactor High Tier Reactor Safety Requirements and for Naval Reactors Approval to Transmit These Requirements to JPL

    Energy Technology Data Exchange (ETDEWEB)

    D. Kokkinos

    2005-04-28

    The purpose of this letter is to request Naval Reactors comments on the nuclear reactor high tier requirements for the PROMETHEUS space flight reactor design, pre-launch operations, launch, ascent, operation, and disposal, and to request Naval Reactors approval to transmit these requirements to Jet Propulsion Laboratory to ensure consistency between the reactor safety requirements and the spacecraft safety requirements. The proposed PROMETHEUS nuclear reactor high tier safety requirements are consistent with the long standing safety culture of the Naval Reactors Program and its commitment to protecting the health and safety of the public and the environment. In addition, the philosophy on which these requirements are based is consistent with the Nuclear Safety Policy Working Group recommendations on space nuclear propulsion safety (Reference 1), DOE Nuclear Safety Criteria and Specifications for Space Nuclear Reactors (Reference 2), the Nuclear Space Power Safety and Facility Guidelines Study of the Applied Physics Laboratory.

  19. Transmutation of actinides in power reactors.

    Science.gov (United States)

    Bergelson, B R; Gerasimov, A S; Tikhomirov, G V

    2005-01-01

    Power reactors can be used for partial short-term transmutation of radwaste. This transmutation is beneficial in terms of subsequent storage conditions for spent fuel in long-term storage facilities. CANDU-type reactors can transmute the main minor actinides from two or three reactors of the VVER-1000 type. A VVER-1000-type reactor can operate in a self-service mode with transmutation of its own actinides.

  20. Heavy Water Reactor; Reacteurs a eau lourde

    Energy Technology Data Exchange (ETDEWEB)

    Yu, St.; HOpwood, J.; Meneley, D. [Energie Atomique du Canada (Canada)

    2000-04-01

    This document deals with the Heavy Water Reactor (HWR) technology and especially the Candu (Canada Deuterium Uranium) reactor. This reactors type offers many advantages that promote them for the future. General concepts, a description of the Candu nuclear power plants, the safety systems, the fuel cycle and economical and environmental aspects are included. (A.L.B.)

  1. Heat-pipe thermionic reactor concept

    DEFF Research Database (Denmark)

    Storm Pedersen, E.

    1967-01-01

    Main components are reactor core, heat pipe, thermionic converter, secondary cooling system, and waste heat radiator; thermal power generated in reactor core is transported by heat pipes to thermionic converters located outside reactor core behind radiation shield; thermionic emitters are in direct...

  2. Some new viewpoints in reactor noise analysis

    Institute of Scientific and Technical Information of China (English)

    罗征培; 李富; 等

    1996-01-01

    It is propsed that the linearity criterion and order criterion via frequency spectrum features without any limitation of the model's phase can be used in reactor noise analysis.The time constant,natural frequency as well as the recovered transfer function of reactors can bhe obtained via the analyzable model based on reactor noise.

  3. Operating Modes Of Chemical Reactors Of Polymerization

    Directory of Open Access Journals (Sweden)

    Meruyert Berdieva

    2012-05-01

    Full Text Available In the work the issues of stable technological modes of operation of main devices of producing polysterol reactors have been researched as well as modes of stable operation of a chemical reactor have been presented, which enables to create optimum mode parameters of polymerization process, to prevent emergency situations of chemical reactor operation in industrial conditions.

  4. Laminar Entrained Flow Reactor (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-02-01

    The Laminar Entrained Flow Reactor (LEFR) is a modular, lab scale, single-user reactor for the study of catalytic fast pyrolysis (CFP). This system can be employed to study a variety of reactor conditions for both in situ and ex situ CFP.

  5. Silica-Immobilized Enzyme Reactors

    Science.gov (United States)

    2007-08-01

    immobilized artificial membrane chromatography and lysophospholipid micellar electrokinetic chromatography . J. Chromatogr. A 1998, 810, 95-103. 50...Journal of Liquid Chromatography and Related Technologies. Air Force Research Laboratory Materials and Manufacturing Directorate Airbase...immobilized enzyme reactors (IMERs) can also be integrated directly to further analytical methods such as liquid chromatography or mass spectrometry.[6] In

  6. Nozzle for electric dispersion reactor

    Science.gov (United States)

    Sisson, Warren G.; Basaran, Osman A.; Harris, Michael T.

    1995-01-01

    A nozzle for an electric dispersion reactor includes two concentric electrodes, the inner one of the two delivering disperse phase fluid into a continuous phase fluid. A potential difference generated by a voltage source creates a dispersing electric field at the end of the inner electrode.

  7. A Simple Tubular Reactor Experiment.

    Science.gov (United States)

    Hudgins, Robert R.; Cayrol, Bertrand

    1981-01-01

    Using the hydrolysis of crystal violet dye by sodium hydroxide as an example, the theory, apparatus, and procedure for a laboratory demonstration of tubular reactor behavior are described. The reaction presented can occur at room temperature and features a color change to reinforce measured results. (WB)

  8. High temperature catalytic membrane reactors

    Energy Technology Data Exchange (ETDEWEB)

    1990-03-01

    Current state-of-the-art inorganic oxide membranes offer the potential of being modified to yield catalytic properties. The resulting modules may be configured to simultaneously induce catalytic reactions with product concentration and separation in a single processing step. Processes utilizing such catalytically active membrane reactors have the potential for dramatically increasing yield reactions which are currently limited by either thermodynamic equilibria, product inhibition, or kinetic selectivity. Examples of commercial interest include hydrogenation, dehydrogenation, partial and selective oxidation, hydrations, hydrocarbon cracking, olefin metathesis, hydroformylation, and olefin polymerization. A large portion of the most significant reactions fall into the category of high temperature, gas phase chemical and petrochemical processes. Microporous oxide membranes are well suited for these applications. A program is proposed to investigate selected model reactions of commercial interest (i.e. dehydrogenation of ethylbenzene to styrene and dehydrogenation of butane to butadiene) using a high temperature catalytic membrane reactor. Membranes will be developed, reaction dynamics characterized, and production processes developed, culminating in laboratory-scale demonstration of technical and economic feasibility. As a result, the anticipated increased yield per reactor pass economic incentives are envisioned. First, a large decrease in the temperature required to obtain high yield should be possible because of the reduced driving force requirement. Significantly higher conversion per pass implies a reduced recycle ratio, as well as reduced reactor size. Both factors result in reduced capital costs, as well as savings in cost of reactants and energy.

  9. Nuclear Reactors and Technology; (USA)

    Energy Technology Data Exchange (ETDEWEB)

    Cason, D.L.; Hicks, S.C. (eds.)

    1991-01-01

    Nuclear Reactors and Technology (NRT) announces on a monthly basis the current worldwide information available from the open literature on nuclear reactors and technology, including all aspects of power reactors, components and accessories, fuel elements, control systems, and materials. This publication contains the abstracts of DOE reports, journal articles, conference papers, patents, theses, and monographs added to the Energy Science and Technology Database (EDB) during the past month. Also included are US information obtained through acquisition programs or interagency agreements and international information obtained through the International Energy Agency's Energy Technology Data Exchange or government-to-government agreements. The digests in NRT and other citations to information on nuclear reactors back to 1948 are available for online searching and retrieval on EDB and Nuclear Science Abstracts (NSA) database. Current information, added daily to EDB, is available to DOE and its contractors through the DOE integrated Technical Information System. Customized profiles can be developed to provide current information to meet each user's needs.

  10. British high flux beam reactor.

    Science.gov (United States)

    Egelstaff, P A

    1970-10-24

    The neutron scattering technique has become an accepted method for the study of condensed matter. Because of the great scientific and technical value of neutron experiments and the growing body of users, several proposals have been made during the past decade for a nuclear reactor devoted primarily to this technique. This article reviews the reasons for and history behind these proposals.

  11. Nuclear reactors and fuel cycle

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-07-01

    The Nuclear Fuel Center (CCN) of IPEN produces nuclear fuel for the continuous operation of the IEA-R1 research reactor of IPEN. The serial production started in 1988, when the first nuclear fuel element was delivered for IEA-R1. In 2011, CCN proudly presents the 100{sup th} nuclear fuel element produced. Besides routine production, development of new technologies is also a permanent concern at CCN. In 2005, U{sub 3}O{sub 8} were replaced by U{sub 3}Si{sub 2}-based fuels, and the research of U Mo is currently under investigation. Additionally, the Brazilian Multipurpose Research Reactor (RMB), whose project will rely on the CCN for supplying fuel and uranium targets. Evolving from an annual production from 10 to 70 nuclear fuel elements, plus a thousand uranium targets, is a huge and challenging task. To accomplish it, a new and modern Nuclear Fuel Factory is being concluded, and it will provide not only structure for scaling up, but also a safer and greener production. The Nuclear Engineering Center has shown, along several years, expertise in the field of nuclear, energy systems and correlated areas. Due to the experience obtained during decades in research and technological development at Brazilian Nuclear Program, personnel has been trained and started to actively participate in design of the main system that will compose the Brazilian Multipurpose Reactor (RMB) which will make Brazil self-sufficient in production of radiopharmaceuticals. The institution has participated in the monitoring and technical support concerning the safety, licensing and modernization of the research reactors IPEN/MB-01 and IEA-R1. Along the last two decades, numerous specialized services of engineering for the Brazilian nuclear power plants Angra 1 and Angra 2 have been carried out. The contribution in service, research, training, and teaching in addition to the development of many related technologies applied to nuclear engineering and correlated areas enable the institution to

  12. A new MTR fuel for a new MTR reactor: UMo for the Jules Horowitz reactor

    Energy Technology Data Exchange (ETDEWEB)

    Guigon, B. [CEA Cadarache, F-13108 Saint Paul lez Durance (France); Vacelet, H. [CERCA, Romans (France); Dornbusch, D. [Technicatome, Aix en Provence (France)

    2000-07-01

    Within some years, the Jules Horowitz Reactor will be the only working experimental reactor (material and fuel testing reactor) in France. It will have to provide facilities for a wide range of needs from activation analysis to power reactor fuel qualification. In this paper the main characteristics of the Jules Horowitz Reactor are presented. Safety criteria are explained. Finally, merits and disadvantages of UMo compared to the standard U{sub 3}Si{sub 2} fuel are discussed. (author)

  13. Heterogeneous Recycling in Fast Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Forget, Benoit; Pope, Michael; Piet, Steven J.; Driscoll, Michael

    2012-07-30

    Current sodium fast reactor (SFR) designs have avoided the use of depleted uranium blankets over concerns of creating weapons grade plutonium. While reducing proliferation risks, this restrains the reactor design space considerably. This project will analyze various blanket and transmutation target configurations that could broaden the design space while still addressing the non-proliferation issues. The blanket designs will be assessed based on the transmutation efficiency of key minor actinide (MA) isotopes and also on mitigation of associated proliferation risks. This study will also evaluate SFR core performance under different scenarios in which depleted uranium blankets are modified to include minor actinides with or without moderators (e.g. BeO, MgO, B4C, and hydrides). This will be done in an effort to increase the sustainability of the reactor and increase its power density while still offering a proliferation resistant design with the capability of burning MA waste produced from light water reactors (LWRs). Researchers will also analyze the use of recycled (as opposed to depleted) uranium in the blankets. The various designs will compare MA transmutation efficiency, plutonium breeding characteristics, proliferation risk, shutdown margins and reactivity coefficients with a current reference sodium fast reactor design employing homogeneous recycling. The team will also evaluate the out-of-core accumulation and/or burn-down rates of MAs and plutonium isotopes on a cycle-by-cycle basis. This cycle-by-cycle information will be produced in a format readily usable by the fuel cycle systems analysis code, VISION, for assessment of the sustainability of the deployment scenarios.

  14. Reactor monitoring and safeguards using antineutrino detectors

    CERN Document Server

    Bowden, N S

    2008-01-01

    Nuclear reactors have served as the antineutrino source for many fundamental physics experiments. The techniques developed by these experiments make it possible to use these very weakly interacting particles for a practical purpose. The large flux of antineutrinos that leaves a reactor carries information about two quantities of interest for safeguards: the reactor power and fissile inventory. Measurements made with antineutrino detectors could therefore offer an alternative means for verifying the power history and fissile inventory of a reactors, as part of International Atomic Energy Agency (IAEA) and other reactor safeguards regimes. Several efforts to develop this monitoring technique are underway across the globe.

  15. Neutrino Mixing Discriminates Geo-reactor Models

    CERN Document Server

    Dye, S T

    2009-01-01

    Geo-reactor models suggest the existence of natural nuclear reactors at different deep-earth locations with loosely defined output power. Reactor fission products undergo beta decay with the emission of electron antineutrinos, which routinely escape the earth. Neutrino mixing distorts the energy spectrum of the electron antineutrinos. Characteristics of the distorted spectrum observed at the earth's surface could specify the location of a geo-reactor, discriminating the models and facilitating more precise power measurement. The existence of a geo-reactor with known position could enable a precision measurement of the neutrino oscillation parameter delta-mass-squared.

  16. Reactor assessments of advanced bumpy torus configurations

    Energy Technology Data Exchange (ETDEWEB)

    Uckan, N.A.; Owen, L.W.; Spong, D.A.; Miller, R.L.; Ard, W.B.; Pipkins, J.F.; Schmitt, R.J.

    1983-01-01

    Recently, several configurational approaches and concept improvement schemes were introduced for enhancing the performance of the basic ELMO Bumpy Torus (EBT) concept and for improving its reactor potential. These configurations include planar racetrack and square geometries, Andreoletti coil systems, and bumpy torus-stellarator hybrids (which include twisted racetrack and helical axis stellarator-snakey torus). Preliminary evaluations of reactor implications of each of these configurations have been carried out based on magnetics (vacuum) calculations, transport and scaling relationships, and stability properties. Results indicate favorable reactor projections with a significant reduction in reactor physical size as compared to conventional EBT reactor designs carried out in the past.

  17. Refurbishment of existing research reactors for BNCT

    Energy Technology Data Exchange (ETDEWEB)

    Jatuff, F.E.; Gessaghi, V. [INVAP S.E., de Bariloche (Argentina)

    1997-12-01

    Some research reactors have been selected for the development of boron neutron capture therapy (BNCT) in the United States like the Massachusetts Institute of Technology research reactor, the University of Missouri research reactor 2 or the Brookhaven Medical Research Reactor, among others. These reactors have received excellent analyses and designs to accommodate extremely optimized beam shaping assemblies (BSAs) for the proper tuning of neutron spectra and absorption of undesired particles such as photons and fast neutrons. Due to the importance of BNCT in these facilities, the physicists and engineers have used many degrees of freedom for the optimization process.

  18. Tandem Mirror Reactor Systems Code (Version I)

    Energy Technology Data Exchange (ETDEWEB)

    Reid, R.L.; Finn, P.A.; Gohar, M.Y.; Barrett, R.J.; Gorker, G.E.; Spampinaton, P.T.; Bulmer, R.H.; Dorn, D.W.; Perkins, L.J.; Ghose, S.

    1985-09-01

    A computer code was developed to model a Tandem Mirror Reactor. Ths is the first Tandem Mirror Reactor model to couple, in detail, the highly linked physics, magnetics, and neutronic analysis into a single code. This report describes the code architecture, provides a summary description of the modules comprising the code, and includes an example execution of the Tandem Mirror Reactor Systems Code. Results from this code for two sensitivity studies are also included. These studies are: (1) to determine the impact of center cell plasma radius, length, and ion temperature on reactor cost and performance at constant fusion power; and (2) to determine the impact of reactor power level on cost.

  19. Savannah River Site production reactor technical specifications. K Production Reactor

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    These technical specifications are explicit restrictions on the operation of the Savannah River Site K Production Reactor. They are designed to preserve the validity of the plant safety analysis by ensuring that the plant is operated within the required conditions bounded by the analysis, and with the operable equipment that is assumed to mitigate the consequences of an accident. Technical specifications preserve the primary success path relied upon to detect and respond to accidents. This report describes requirements on thermal-hydraulic limits; limiting conditions for operation and surveillance for the reactor, power distribution control, instrumentation, process water system, emergency cooling and emergency shutdown systems, confinement systems, plant systems, electrical systems, components handling, and special test exceptions; design features; and administrative controls.

  20. CFD Simulation on Ethylene Furnace Reactor Tubes

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Different mathematical models for ethylene furnace reactor tubes were reviewed. On the basis of these models a new mathematical simulation approach for reactor tubes based on computational fluid dynamics (CFD) technique was presented. This approach took the flow, heat transfer, mass transfer and thermal cracking reactions in the reactor tubes into consideration. The coupled reactor model was solved with the SIMPLE algorithm. Some detailed information about the flow field, temperature field and concentration distribution in the reactor tubes was obtained, revealing the basic characteristics of the hydrodynamic phenomena and reaction behavior in the reactor tubes. The CFD approach provides the necessary information for conclusive decisions regarding the production optimization, the design and improvement of reactor tubes, and the new techniques implementation.

  1. Advanced reactor physics methods for heterogeneous reactor cores

    Science.gov (United States)

    Thompson, Steven A.

    To maintain the economic viability of nuclear power the industry has begun to emphasize maximizing the efficiency and output of existing nuclear power plants by using longer fuel cycles, stretch power uprates, shorter outage lengths, mixed-oxide (MOX) fuel and more aggressive operating strategies. In order to accommodate these changes, while still satisfying the peaking factor and power envelope requirements necessary to maintain safe operation, more complexity in commercial core designs have been implemented, such as an increase in the number of sub-batches and an increase in the use of both discrete and integral burnable poisons. A consequence of the increased complexity of core designs, as well as the use of MOX fuel, is an increase in the neutronic heterogeneity of the core. Such heterogeneous cores introduce challenges for the current methods that are used for reactor analysis. New methods must be developed to address these deficiencies while still maintaining the computational efficiency of existing reactor analysis methods. In this thesis, advanced core design methodologies are developed to be able to adequately analyze the highly heterogeneous core designs which are currently in use in commercial power reactors. These methodological improvements are being pursued with the goal of not sacrificing the computational efficiency which core designers require. More specifically, the PSU nodal code NEM is being updated to include an SP3 solution option, an advanced transverse leakage option, and a semi-analytical NEM solution option.

  2. Reactor pulse repeatability studies at the annular core research reactor

    Energy Technology Data Exchange (ETDEWEB)

    DePriest, K.R. [Applied Nuclear Technologies, Sandia National Laboratories, Mail Stop 1146, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States); Trinh, T.Q. [Nuclear Facility Operations, Sandia National Laboratories, Mail Stop 0614, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States); Luker, S. M. [Applied Nuclear Technologies, Sandia National Laboratories, Mail Stop 1146, Post Office Box 5800, Albuquerque, NM 87185-1146 (United States)

    2011-07-01

    The Annular Core Research Reactor (ACRR) at Sandia National Laboratories is a water-moderated pool-type reactor designed for testing many types of objects in the pulse and steady-state mode of operations. Personnel at Sandia began working to improve the repeatability of pulse operations for experimenters in the facility. The ACRR has a unique UO{sub 2}-BeO fuel that makes the task of producing repeatable pulses difficult with the current operating procedure. The ACRR produces a significant quantity of photoneutrons through the {sup 9}Be({gamma}, n){sup 8}Be reaction in the fuel elements. The photoneutrons are the result of the gammas produced during fission and in fission product decay, so their production is very much dependent on the reactor power history and changes throughout the day/week of experiments in the facility. Because the photoneutrons interfere with the delayed-critical measurements required for accurate pulse reactivity prediction, a new operating procedure was created. The photoneutron effects at delayed critical are minimized when using the modified procedure. In addition, the pulse element removal time is standardized for all pulse operations with the modified procedure, and this produces less variation in reactivity removal times. (authors)

  3. In-reactor performance of pressure tubes in CANDU reactors

    Science.gov (United States)

    Rodgers, D. K.; Coleman, C. E.; Griffiths, M.; Bickel, G. A.; Theaker, J. R.; Muir, I.; Bahurmuz, A. A.; Lawrence, S. St.; Resta Levi, M.

    2008-12-01

    The pressure tubes in CANDU reactors have been operating for times up to about 25 years. The in-reactor performance of Zr-2.5Nb pressure tubes has been evaluated by sampling and periodic inspection. This paper describes the behaviour and discusses the factors controlling the behaviour of these components in currently operating CANDU reactors. The mechanical properties (such as ultimate tensile strength, UTS, and fracture toughness), and delayed-hydride-cracking properties (crack growth rate Vc, and threshold stress intensity factor, KIH) change with irradiation; the former reach a limiting value at a fluence of Pressure tubes exhibit elongation and diametral expansion. The deformation behaviour is a function of operating conditions and material properties that vary from tube-to-tube and as a function of axial location. Semi-empirical predictive models have been developed to describe the deformation response of average tubes as a function of operating conditions. For corrosion and, more importantly deuterium pickup, semi-empirical predictive models have also been developed to represent the behaviour of an average tube. The effect of material variability on corrosion behaviour is less well defined compared with other properties. Improvements in manufacturing have increased fracture resistance by minimising trace elements, especially H and Cl, and reduced variability by tightening controls on forming parameters, especially hot-working temperatures.

  4. Gas-liquid autoxidation reactors

    Energy Technology Data Exchange (ETDEWEB)

    Morbidelli, M.; Paludetto, R.; Carra, S.

    1986-01-01

    A procedure for the simulation of autoxidation gas-liquid reactors has been developed based both on mathematical models and laboratory experiments. It has been shown that the complex radical chain mechanism of the autoxidation process can be simulated through two global parallel reactions, whose rates are obtained by assuming pseudo-steady-state concentration values for all the radical species involved. Using ethylbenzene autoxidation as a model reaction, an experimental analysis has been performed in order to estimate all the kinetic parameters of the model. The effect of the interaction between gas-liquid mass-transfer phenomena and the complex kinetic mechanism on the overall performance of an autoxidation reactor has been examined in detail within the framework of the liquid film model.

  5. Transport simulation for EBT reactor

    Energy Technology Data Exchange (ETDEWEB)

    Uckan, T.; Uckan, N.A.; Jaeger, E.F.

    1983-08-01

    Transport simulation and modeling studies for the ELMO Bumpy Torus (EBT) reactor are carried out by using zero-dimensional (0-D) and one-and-one-half-dimensional (1 1/2-D) transport calculations. The time-dependent 0-D model is used for global analysis, whereas the 1 1/2-D radial transport code is used for accurate determination of density, temperature, and ambipolar potential profiles and of the role of these profiles in reactor plasma performance. Analysis with the 1 1/2-D transport code shows that profile effects near the outer edge of the hot electron ring lead to enhanced confinement by at least a factor of 2 to 5 beyond the simple scaling that is obtained from the global analysis. The radial profiles of core plasma density and temperatures (or core pressure) obtained from 1 1/2-D transport calculations are found to be similar to those theoretically required for stability.

  6. Nuclear reactor alignment plate configuration

    Energy Technology Data Exchange (ETDEWEB)

    Altman, David A; Forsyth, David R; Smith, Richard E; Singleton, Norman R

    2014-01-28

    An alignment plate that is attached to a core barrel of a pressurized water reactor and fits within slots within a top plate of a lower core shroud and upper core plate to maintain lateral alignment of the reactor internals. The alignment plate is connected to the core barrel through two vertically-spaced dowel pins that extend from the outside surface of the core barrel through a reinforcement pad and into corresponding holes in the alignment plate. Additionally, threaded fasteners are inserted around the perimeter of the reinforcement pad and into the alignment plate to further secure the alignment plate to the core barrel. A fillet weld also is deposited around the perimeter of the reinforcement pad. To accomodate thermal growth between the alignment plate and the core barrel, a gap is left above, below and at both sides of one of the dowel pins in the alignment plate holes through with the dowel pins pass.

  7. Fluidized bed coal combustion reactor

    Science.gov (United States)

    Moynihan, P. I.; Young, D. L. (Inventor)

    1981-01-01

    A fluidized bed coal reactor includes a combination nozzle-injector ash-removal unit formed by a grid of closely spaced open channels, each containing a worm screw conveyor, which function as continuous ash removal troughs. A pressurized air-coal mixture is introduced below the unit and is injected through the elongated nozzles formed by the spaces between the channels. The ash build-up in the troughs protects the worm screw conveyors as does the cooling action of the injected mixture. The ash layer and the pressure from the injectors support a fluidized flame combustion zone above the grid which heats water in boiler tubes disposed within and/or above the combustion zone and/or within the walls of the reactor.

  8. Fast breeder reactor protection system

    Science.gov (United States)

    van Erp, J.B.

    1973-10-01

    Reactor protection is provided for a liquid-metal-fast breeder reactor core by measuring the coolant outflow temperature from each of the subassemblies of the core. The outputs of the temperature sensors from a subassembly region of the core containing a plurality of subassemblies are combined in a logic circuit which develops a scram alarm if a predetermined number of the sensors indicate an over temperature condition. The coolant outflow from a single subassembly can be mixed with the coolant outflow from adjacent subassemblies prior to the temperature sensing to increase the sensitivity of the protection system to a single subassembly failure. Coherence between the sensors can be required to discriminate against noise signals. (Official Gazette)

  9. Reactor vessel lower head integrity

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, A.M.

    1997-02-01

    On March 28, 1979, the Three Mile Island Unit 2 (TMI-2) nuclear power plant underwent a prolonged small break loss-of-coolant accident that resulted in severe damage to the reactor core. Post-accident examinations of the TMI-2 reactor core and lower plenum found that approximately 19,000 kg (19 metric tons) of molten material had relocated onto the lower head of the reactor vessel. Results of the OECD TMI-2 Vessel Investigation Project concluded that a localized hot spot of approximately 1 meter diameter had existed on the lower head. The maximum temperature on the inner surface of the reactor pressure vessel (RPV) in this region reached 1100{degrees}C and remained at that temperature for approximately 30 minutes before cooling occurred. Even under the combined loads of high temperature and high primary system pressure, the TMI-2 RPV did not fail. (i.e. The pressure varied from about 8.5 to 15 MPa during the four-hour period following the relocation of melt to the lower plenum.) Analyses of RPV failure under these conditions, using state-of-the-art computer codes, predicted that the RPV should have failed via local or global creep rupture. However, the vessel did not fail; and it has been hypothesized that rapid cooling of the debris and the vessel wall by water that was present in the lower plenum played an important role in maintaining RPV integrity during the accident. Although the exact mechanism(s) of how such cooling occurs is not known, it has been speculated that cooling in a small gap between the RPV wall and the crust, and/or in cracks within the debris itself, could result in sufficient cooling to maintain RPV integrity. Experimental data are needed to provide the basis to better understand these phenomena and improve models of RPV failure in severe accident codes.

  10. 覆冰四分裂导线空气动力系数数值模拟%Numerical investigation on aerodynamic coefficients of iced quad bundle conductor

    Institute of Scientific and Technical Information of China (English)

    蔡萌琦; 严波; 吕欣; 周林抒; 阎东; 陈瑞

    2013-01-01

    Numerical model for fluid flow around a typical iced quad bundle conductor was set up, and the aerodynamic coefficients varying with the wind attack angle of conductor were numerically investigated by means of FLUENT software. The Den Hartog and Nigol coefficients determined by numerical simulation are in agreement with those obtained by the wind tunnel test. Moreover, the galloping of iced quad bundle conductor lines based on aerodynamic coefficients obtained by numerical simulation and wind tunnel test were simulated respectively by ABAQUS software. The galloping characteristics of the transmission lines based on aerodynamic coefficients deduced by calculation and test are in coincidence, which demonstrates the availability of applying the numerical simulation method to obtain aerodynamic coefficients of iced conductors in the analysis of galloping of transmission lines.%利用Fluent流体动力学分析软件计算典型覆冰四分裂导线在特定风速下的绕流问题,所得各覆冰子导线空气动力系数随风攻角变化曲线与由风洞试验所得规律一致.基于数值模拟和风洞试验所得气动系数确定的Den Hartog系数与Nigol系数随风攻角的变化结果吻合.利用由数值模拟和风洞试验获所得气动参数,采用Abaqus有限元软件模拟典型线路段的舞动,通过舞动特性分析比较发现,利用该两组气动系数模拟得到的导线舞动特性一致,表明采用数值模拟方法确定覆冰导线的空气动力系数可用于模拟覆冰导线舞动.

  11. Quad-tree partition model of object tracking%目标跟踪中的四叉树分块模型

    Institute of Scientific and Technical Information of China (English)

    张文俊; 张雄

    2015-01-01

    In order to establish a target model to describe image structure characteristics in the field of computer vision, a quad-tree partition model based on density estimation is proposed. The local density estimation model is established by using quad-tree partition method in the target image block division, according to statistical features of pixel values and scales of each block. Analysis of experimental results shows that the method not only describes structural characteristics which the global density estimation model cannot do, but also describes details of the target distinctly with less number of blocks. At the same time, algorithm based on the proposed model simplifies calculation process of density estimation and has obvious advantages of target tracking applications over other algorithms.%针对计算机视觉领域中,建立能够描述图像结构特性的目标模型问题,提出了一种基于四叉树分块的密度估计模型。采用四叉树分块方法对目标图像块进行划分,根据各分块的尺度和像素值统计特性建立局部的密度估计模型。实验结果和分析表明,基于四叉树分块的局部密度估计模型解决了全局密度估计模型无法描述结构特性的问题,而且用较少的分块数量有针对性地描述了目标的细节,同时简化了密度估计算法的计算过程,在目标跟踪应用中较其他算法表现出较优的性能。

  12. The ARIES tokamak reactor study

    Energy Technology Data Exchange (ETDEWEB)

    1989-10-01

    The ARIES study is a community effort to develop several visions of tokamaks as fusion power reactors. The aims are to determine the potential economics, safety, and environmental features of a range of possible tokamak reactors, and to identify physics and technology areas with the highest leverage for achieving the best tokamak reactor. Three ARIES visions are planned, each having a different degree of extrapolation from the present data base in physics and technology. The ARIES-I design assumes a minimum extrapolation from current tokamak physics (e.g., 1st stability) and incorporates technological advances that can be available in the next 20 to 30 years. ARIES-II is a DT-burning tokamak which would operate at a higher beta in the 2nd MHD stability regime. It employs both potential advances in the physics and expected advances in technology and engineering. ARIES-II will examine the potential of the tokamak and the D{sup 3}He fuel cycle. This report is a collection of 14 papers on the results of the ARIES study which were presented at the IEEE 13th Symposium on Fusion Engineering (October 2-6, 1989, Knoxville, TN). This collection describes the ARIES research effort, with emphasis on the ARIES-I design, summarizing the major results, the key technical issues, and the central conclusions.

  13. Actinide transmutation in nuclear reactors

    Energy Technology Data Exchange (ETDEWEB)

    Bultman, J.H.

    1995-01-17

    An optimization method is developed to maximize the burning capability of the ALMR while complying with all constraints imposed on the design for reliability and safety. This method leads to a maximal transuranics enrichment, which is being limited by constraints on reactivity. The enrichment can be raised by using the neutrons less efficiently by increasing leakage from the fuel. With the developed optimization method, a metallic and an oxide fueled ALMR were optimized. Both reactors perform equally well considering the burning of transuranics. However, metallic fuel has a much higher heat conductivity coefficient, which in general leads to better safety characteristics. In search of a more effective waste transmuter, a modified Molten Salt Reactor was designed. A MSR operates on a liquid fuel salt which makes continuous refueling possible, eliminating the issue of the burnup reactivity loss. Also, a prompt negative reactivity feedback is possible for an overmoderated reactor design, even when the Doppler coefficient is positive, due to the fuel expansion with fuel temperature increase. Furthermore, the molten salt fuel can be reprocessed based on a reduction process which is not sensitive to the short-lived spontaneously fissioning actinides. (orig./HP).

  14. Assessment of the thorium fuel cycle in power reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.; Homan, F.J.; Allen, E.J.

    1977-01-01

    A study was conducted at Oak Ridge National Laboratory to evaluate the role of thorium fuel cycles in power reactors. Three thermal reactor systems were considered: Light Water Reactors (LWRs); High-Temperature Gas-Cooled Reactors (HTGRs); and Heavy Water Reactors (HWRs) of the Canadian Deuterium Uranium Reactor (CANDU) type; most of the effort was on these systems. A summary comparing thorium and uranium fuel cycles in Fast Breeder Reactors (FBRs) was also compiled.

  15. Advanced Safeguards Approaches for New Fast Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Durst, Philip C.; Therios, Ike; Bean, Robert; Dougan, A.; Boyer, Brian; Wallace, Rick L.; Ehinger, Michael H.; Kovacic, Don N.; Tolk, K.

    2007-12-15

    This third report in the series reviews possible safeguards approaches for new fast reactors in general, and the ABR in particular. Fast-neutron spectrum reactors have been used since the early 1960s on an experimental and developmental level, generally with fertile blanket fuels to “breed” nuclear fuel such as plutonium. Whether the reactor is designed to breed plutonium, or transmute and “burn” actinides depends mainly on the design of the reactor neutron reflector and the whether the blanket fuel is “fertile” or suitable for transmutation. However, the safeguards issues are very similar, since they pertain mainly to the receipt, shipment and storage of fresh and spent plutonium and actinide-bearing “TRU”-fuel. For these reasons, the design of existing fast reactors and details concerning how they have been safeguarded were studied in developing advanced safeguards approaches for the new fast reactors. In this regard, the design of the Experimental Breeder Reactor-II “EBR-II” at the Idaho National Laboratory (INL) was of interest, because it was designed as a collocated fast reactor with a pyrometallurgical reprocessing and fuel fabrication line – a design option being considered for the ABR. Similarly, the design of the Fast Flux Facility (FFTF) on the Hanford Site was studied, because it was a successful prototype fast reactor that ran for two decades to evaluate fuels and the design for commercial-scale fast reactors.

  16. Investigation of molten salt fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, Kenichi; Konomura, Mamoru [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan)

    2002-05-01

    On survey research for practicability strategy of fast reactor (FR) (phase 1), to extract future practicability image candidates of FR from wide options, in addition to their survey and investigation objects of not only solid fuel reactors of conventional research object but also molten salt reactor as a flowing fuel reactor, investigation on concept of molten salt FR plant was carried out. As a part of the first step of the survey research for practicability strategy, a basic concept on plant centered at nuclear reactor facility using chloride molten salt reactor capable of carrying out U-Pu cycle was examined, to perform a base construction to evaluate economical potential for a practical FBR. As a result, a result could be obtained that because of inferior fuel inventory and heat transmission to those in Na cooling reactor in present knowledge, mass of reactor vessel and intermediate heat exchanger were to widely increased to expect reduction of power generation unit price even on considering cheapness of its fuel cycle cost. Therefore, at present step further investigation on concept design of the chloride molten salt reactor plant system is too early in time, and it is at a condition where basic and elementary researches aiming at upgrading of economical efficiency such as wide reduction of fuel inventory, a measure expectable for remarkable rationalization effect of reprocessing system integrating a reactor to a processing facility, and so on. (G.K.)

  17. Performance of a multipurpose research electrochemical reactor

    Energy Technology Data Exchange (ETDEWEB)

    Henquin, E.R. [Programa de Electroquimica Aplicada e Ingenieria Electroquimica (PRELINE), Facultad de Ingenieria Quimica, Universidad Nacional del Litoral, Santiago del Estero 2829, S3000AOM Santa Fe (Argentina); Bisang, J.M., E-mail: jbisang@fiq.unl.edu.ar [Programa de Electroquimica Aplicada e Ingenieria Electroquimica (PRELINE), Facultad de Ingenieria Quimica, Universidad Nacional del Litoral, Santiago del Estero 2829, S3000AOM Santa Fe (Argentina)

    2011-07-01

    Highlights: > For this reactor configuration the current distribution is uniform. > For this reactor configuration with bipolar connection the leakage current is small. > The mass-transfer conditions are closely uniform along the electrode. > The fluidodynamic behaviour can be represented by the dispersion model. > This reactor represents a suitable device for laboratory trials. - Abstract: This paper reports on a multipurpose research electrochemical reactor with an innovative design feature, which is based on a filter press arrangement with inclined segmented electrodes and under a modular assembly. Under bipolar connection, the fraction of leakage current is lower than 4%, depending on the bipolar Wagner number, and the current distribution is closely uniform. When a turbulence promoter is used, the local mass-transfer coefficient shows a variation of {+-}10% with respect to its mean value. The fluidodynamics of the reactor responds to the dispersion model with a Peclet number higher than 10. It is concluded that this reactor is convenient for laboratory research.

  18. Molten-Salt Depleted-Uranium Reactor

    CERN Document Server

    Dong, Bao-Guo; Gu, Ji-Yuan

    2015-01-01

    The supercritical, reactor core melting and nuclear fuel leaking accidents have troubled fission reactors for decades, and greatly limit their extensive applications. Now these troubles are still open. Here we first show a possible perfect reactor, Molten-Salt Depleted-Uranium Reactor which is no above accident trouble. We found this reactor could be realized in practical applications in terms of all of the scientific principle, principle of operation, technology, and engineering. Our results demonstrate how these reactors can possess and realize extraordinary excellent characteristics, no prompt critical, long-term safe and stable operation with negative feedback, closed uranium-plutonium cycle chain within the vessel, normal operation only with depleted-uranium, and depleted-uranium high burnup in reality, to realize with fission nuclear energy sufficiently satisfying humanity long-term energy resource needs, as well as thoroughly solve the challenges of nuclear criticality safety, uranium resource insuffic...

  19. Sulfide toxicity kinetics of a uasb reactor

    Directory of Open Access Journals (Sweden)

    D. R. Paula Jr.

    2009-12-01

    Full Text Available The effect of sulfide toxicity on kinetic parameters of anaerobic organic matter removal in a UASB (up-flow anaerobic sludge blanket reactor is presented. Two lab-scale UASB reactors (10.5 L were operated continuously during 12 months. The reactors were fed with synthetic wastes prepared daily using glucose, ammonium acetate, methanol and nutrient solution. One of the reactors also received increasing concentrations of sodium sulfide. For both reactors, the flow rate of 16 L.d-1 was held constant throughout the experiment, corresponding to a hydraulic retention time of 15.6 hours. The classic model for non-competitive sulfide inhibition was applied to the experimental data for determining the overall kinetic parameter of specific substrate utilization (q and the sulfide inhibition coefficient (Ki. The application of the kinetic parameters determined allows prediction of methanogenesis inhibition and thus the adoption of operating parameters to minimize sulfide toxicity in UASB reactors.

  20. Introduction to the neutron kinetics of nuclear power reactors

    CERN Document Server

    Tyror, J G; Grant, P J

    2013-01-01

    An Introduction to the Neutron Kinetics of Nuclear Power Reactors introduces the reader to the neutron kinetics of nuclear power reactors. Topics covered include the neutron physics of reactor kinetics, feedback effects, water-moderated reactors, fast reactors, and methods of plant control. The reactor transients following faults are also discussed, along with the use of computers in the study of power reactor kinetics. This book is comprised of eight chapters and begins with an overview of the reactor physics characteristics of a nuclear power reactor and their influence on system design and

  1. Investigation of quad-energy high-rate photon counting for X-ray computed tomography using a cadmium telluride detector.

    Science.gov (United States)

    Matsukiyo, Hiroshi; Sato, Eiichi; Oda, Yasuyuki; Yamaguchi, Satoshi; Sato, Yuichi; Hagiwara, Osahiko; Enomoto, Toshiyuki; Watanabe, Manabu; Kusachi, Shinya

    2017-09-10

    To obtain four kinds of tomograms at four different X-ray energy ranges simultaneously, we have constructed a quad-energy (QE) X-ray photon counter with a cadmium telluride (CdTe) detector and four sets of comparators and microcomputers (MCs). X-ray photons are detected using the CdTe detector, and the event pulses produced using amplifiers are sent to four comparators simultaneously to regulate four threshold energies of 20, 33, 50 and 65keV. Using this counter, the energy ranges are 20-33, 33-50, 50-65 and 65-100keV; the maximum energy corresponds to the tube voltage. We performed QE computed tomography (QE-CT) at a tube voltage of 100kV. Using a 0.5-mm-diam lead pinhole, four tomograms were obtained simultaneously at four energy ranges. K-edge CT using iodine and gadolinium media was carried out utilizing two energy ranges of 33-50 and 50-65keV, respectively. At a tube voltage of 100kV and a current of 60 μA, the count rate was 15.2 kilocounts per second (kcps), and the minimum count rates after penetrating objects in QE-CT were regulated to approximately 2 kcps by the tube current. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Body of Knowledge (BOK) for Leadless Quad Flat No-Lead/bottom Termination Components (QFN/BTC) Package Trends and Reliability

    Science.gov (United States)

    Ghaffarian, Reza

    2014-01-01

    Bottom terminated components and quad flat no-lead (BTC/QFN) packages have been extensively used by commercial industry for more than a decade. Cost and performance advantages and the closeness of the packages to the boards make them especially unique for radio frequency (RF) applications. A number of high-reliability parts are now available in this style of package configuration. This report presents a summary of literature surveyed and provides a body of knowledge (BOK) gathered on the status of BTC/QFN and their advanced versions of multi-row QFN (MRQFN) packaging technologies. The report provides a comprehensive review of packaging trends and specifications on design, assembly, and reliability. Emphasis is placed on assembly reliability and associated key design and process parameters because they show lower life than standard leaded package assembly under thermal cycling exposures. Inspection of hidden solder joints for assuring quality is challenging and is similar to ball grid arrays (BGAs). Understanding the key BTC/QFN technology trends, applications, processing parameters, workmanship defects, and reliability behavior is important when judicially selecting and narrowing the follow-on packages for evaluation and testing, as well as for the low risk insertion in high-reliability applications.

  3. Investigation of 2D photonic crystal structure based channel drop filter using quad shaped photonic crystal ring resonator for CWDM system

    Energy Technology Data Exchange (ETDEWEB)

    Chhipa, Mayur Kumar, E-mail: mayurchhipa1@gmail.com; Dusad, Lalit Kumar [Government Engineering College Ajmer, Rajasthan (India); Rajasthan Technical University, Kota, Rajasthan (India)

    2016-05-06

    In this paper, the design & performance of two dimensional (2-D) photonic crystal structure based channel drop filter is investigated using quad shaped photonic crystal ring resonator. In this paper, Photonic Crystal (PhC) based on square lattice periodic arrays of Gallium Indium Phosphide (GaInP) rods in air structure have been investigated using Finite Difference Time Domain (FDTD) method and photonic band gap is being calculated using Plane Wave Expansion (PWE) method. The PhC designs have been optimized for telecommunication wavelength λ= 1571 nm by varying the rods lattice constant. The number of rods in Z and X directions is 21 and 20, with lattice constant 0.540 nm it illustrates that the arrangement of Gallium Indium Phosphide (GaInP) rods in the structure which gives the overall size of the device around 11.4 µm × 10.8 µm. The designed filter gives good dropping efficiency using 3.298, refractive index. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm{sup 2}.

  4. Synergistic use of RADARSAT-2 Ultra Fine and Fine Quad-Pol data to map oilsands infrastructure land: Object-based approach

    Science.gov (United States)

    Jiao, Xianfeng; Zhang, Ying; Guindon, Bert

    2015-06-01

    The landscape of Alberta's oilsands regions is undergoing extensive change due to the creation of infrastructure associated with the exploration for and extraction of this resource. Since most oil sands mining activities take place in remote forests or wetlands, one of the challenges is to collect up-to date and reliable information about the current state of land. Compared to optical sensors, SAR sensors have the advantage of being able to routinely collect imagery for timely monitoring by regulatory agencies. This paper explores the capability of high resolution RADARSAT-2 Ultra Fine and Fine Quad-Pol imagery for mapping oilsands infrastructure land using an object-based classification approach. Texture measurements extracted from Ultra Fine data are used to support an Ultra Fine based classification. Moreover, a radar vegetation index (RVI) calculated from PolSAR data is introduced for improved classification performance. The RVI is helpful in reducing confusion between infrastructure land and low vegetation covered surfaces. When Ultra Fine and PolSAR data are used in combination, the kappa value of well pads and processing facilities detection reached 0.87. In this study, we also found that core hole sites can be identified from early spring Ultra Fine data. With single-date image, kappa value of core hole sites ranged from 0.61 to 0.69.

  5. Microstructured reactors for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Aartun, Ingrid

    2005-07-01

    Small scale hydrogen production by partial oxidation (POX) and oxidative steam reforming (OSR) have been studied over Rh-impregnated microchannel Fecralloy reactors and alumina foams. Trying to establish whether metallic microchannel reactors have special advantages for hydrogen production via catalytic POX or OSR with respect to activity, selectivity and stability was of special interest. The microchannel Fecralloy reactors were oxidised at 1000 deg C to form a {alpha}-Al2O3 layer in the channels in order to enhance the surface area prior to impregnation. Kr-BET measurements showed that the specific surface area after oxidation was approximately 10 times higher than the calculated geometric surface area. Approximately 1 mg Rh was deposited in the channels by impregnation with an aqueous solution of RhCl3. Annular pieces (15 mm o.d.,4 mm i.d., 14 mm length) of extruded {alpha}-Al2O3 foams were impregnated with aqueous solutions of Rh(NO3)3 to obtain 0.01, 0.05 and 0.1 wt.% loadings, as predicted by solution uptake. ICP-AES analyses showed that the actual Rh loadings probably were higher, 0.025, 0.077 and 0.169 wt.% respectively. One of the microchannel Fecralloy reactors and all Al2O3 foams were equipped with a channel to allow for temperature measurement inside the catalytic system. Temperature profiles obtained along the reactor axes show that the metallic microchannel reactor is able to minimize temperature gradients as compared to the alumina foams. At sufficiently high furnace temperature, the gas phase in front of the Rh/Al2O3/Frecralloy microchannel reactor and the 0.025 wt.% Rh/Al2O3 foams ignites. Gas phase ignition leads to lower syngas selectivity and higher selectivity to total oxidation products and hydrocarbon by-products. Before ignition of the gas phase the hydrogen selectivity is increased in OSR as compared to POX, the main contribution being the water-gas shift reaction. After gas phase ignition, increased formation of hydrocarbon by

  6. Reactor Bolshoi Moshchnosti Kalani; Reacteurs RBMK

    Energy Technology Data Exchange (ETDEWEB)

    Bastien, D. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

    2000-01-01

    The Reactor Bolshoi Molshchnosti Kalani (RBMK) are pressure tubes reactor, boiling light water cooled. Exported since 1990 from the ex-USSR, they are today in three independent countries: Russian, Ukraine and Lithuania. Since this date, data exchange with the occident allowed the better knowledge of this reactor type. The design, the technical description (core, fuel, primary system), the safety and the improvement since Chernobyl are detailed. (A.L.B.)

  7. D-D tokamak reactor studies

    Energy Technology Data Exchange (ETDEWEB)

    Evans, K.E. Jr.; Baker, C.C.; Brooks, J.N.; Ehst, D.A.; Finn, P.A.; Jung, J.; Mattas, R.F.; Misra, B.; Smith, D.L.; Stevens, H.C.

    1980-11-01

    A tokamak D-D reactor design, utilizing the advantages of a deuterium-fueled reactor but with parameters not unnecessarily extended from existing D-T designs, is presented. Studies leading to the choice of a design and initial studies of the design are described. The studies are in the areas of plasma engineering, first-wall/blanket/shield design, magnet design, and tritium/fuel/vacuum requirements. Conclusions concerning D-D tokamak reactors are stated.

  8. NASA Reactor Facility Hazards Summary. Volume 1

    Science.gov (United States)

    1959-01-01

    The Lewis Research Center of the National Aeronautics and Space Administration proposes to build a nuclear research reactor which will be located in the Plum Brook Ordnance Works near Sandusky, Ohio. The purpose of this report is to inform the Advisory Committee on Reactor Safeguards of the U. S. Atomic Energy Commission in regard to the design Lq of the reactor facility, the characteristics of the site, and the hazards of operation at this location. The purpose of this research reactor is to make pumped loop studies of aircraft reactor fuel elements and other reactor components, radiation effects studies on aircraft reactor materials and equipment, shielding studies, and nuclear and solid state physics experiments. The reactor is light water cooled and moderated of the MTR-type with a primary beryllium reflector and a secondary water reflector. The core initially will be a 3 by 9 array of MTR-type fuel elements and is designed for operation up to a power of 60 megawatts. The reactor facility is described in general terms. This is followed by a discussion of the nuclear characteristics and performance of the reactor. Then details of the reactor control system are discussed. A summary of the site characteristics is then presented followed by a discussion of the larger type of experiments which may eventually be operated in this facility. The considerations for normal operation are concluded with a proposed method of handling fuel elements and radioactive wastes. The potential hazards involved with failures or malfunctions of this facility are considered in some detail. These are examined first from the standpoint of preventing them or minimizing their effects and second from the standpoint of what effect they might have on the reactor facility staff and the surrounding population. The most essential feature of the design for location at the proposed site is containment of the maximum credible accident.

  9. Plasma spark discharge reactor and durable electrode

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Young I.; Cho, Daniel J.; Fridman, Alexander; Kim, Hyoungsup

    2017-01-10

    A plasma spark discharge reactor for treating water. The plasma spark discharge reactor comprises a HV electrode with a head and ground electrode that surrounds at least a portion of the HV electrode. A passage for gas may pass through the reactor to a location proximate to the head to provide controlled formation of gas bubbles in order to facilitate the plasma spark discharge in a liquid environment.

  10. Heat for industry from nuclear reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kikoin, I.K.; Novikov, V.M.

    Two factors which incline nations toward the use of heat from nuclear reactors for industrial use are: 1) exhaustion of cheap fossil fuel resources, and 2) ecological problems associated both with extraction of fossil fuel from the earth and with its combustion. In addition to the usual problems that beset nuclear reactors, special problems associated with using heat from nuclear reactors in various industries are explored.

  11. Experimental Breeder Reactor I Preservation Plan

    Energy Technology Data Exchange (ETDEWEB)

    Julie Braun

    2006-10-01

    Experimental Breeder Reactor I (EBR I) is a National Historic Landmark located at the Idaho National Laboratory, a Department of Energy laboratory in southeastern Idaho. The facility is significant for its association and contributions to the development of nuclear reactor testing and development. This Plan includes a structural assessment of the interior and exterior of the EBR I Reactor Building from a preservation, rather than an engineering stand point and recommendations for maintenance to ensure its continued protection.

  12. Initiating Events for Multi-Reactor Plant Sites

    Energy Technology Data Exchange (ETDEWEB)

    Muhlheim, Michael David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Flanagan, George F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Poore, III, Willis P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-09-01

    Inherent in the design of modular reactors is the increased likelihood of events that initiate at a single reactor affecting another reactor. Because of the increased level of interactions between reactors, it is apparent that the Probabilistic Risk Assessments (PRAs) for modular reactor designs need to specifically address the increased interactions and dependencies.

  13. Advances in light water reactor technologies

    CERN Document Server

    Saito, Takehiko; Ishiwatari, Yuki; Oka, Yoshiaki

    2010-01-01

    ""Advances in Light Water Reactor Technologies"" focuses on the design and analysis of advanced nuclear power reactors. This volume provides readers with thorough descriptions of the general characteristics of various advanced light water reactors currently being developed worldwide. Safety, design, development and maintenance of these reactors is the main focus, with key technologies like full MOX core design, next-generation digital I&C systems and seismic design and evaluation described at length. This book is ideal for researchers and engineers working in nuclear power that are interested

  14. High Performance Photocatalytic Oxidation Reactor System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Pioneer Astronautics proposes a technology program for the development of an innovative photocatalytic oxidation reactor for the removal and mineralization of...

  15. NCSU reactor sharing program. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Perez, P.B.

    1997-01-10

    The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities. This report is the Final Technical Report for the DOE award reference number DE-FG05-95NE38136 which covers the period September 30, 1995 through September 30, 1996.

  16. Nanostructured Catalytic Reactors for Air Purification Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I project proposes the development of lightweight compact nanostructured catalytic reactors for air purification from toxic gaseous organic...

  17. Nanostructured Catalytic Reactors for Air Purification Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase II project proposes the development of lightweight compact nanostructured catalytic reactors for air purification from toxic gaseous organic...

  18. Advanced nuclear reactor types and technologies

    Energy Technology Data Exchange (ETDEWEB)

    Ignatiev, V. [ed.; Feinberg, O.; Morozov, A. [Russian Research Centre `Kurchatov Institute`, Moscow (Russian Federation); Devell, L. [Studsvik Eco and Safety AB, Nykoeping (Sweden)

    1995-07-01

    The document is a comprehensive world-wide catalogue of concepts and designs of advanced fission reactor types and fuel cycle technologies. Two parts have been prepared: Part 1 Reactors for Power Production and Part 2 Heating and Other Reactor Applications. Part 3, which will cover advanced waste management technology, reprocessing and disposal for different nuclear fission options is planned for compilation during 1995. The catalogue was prepared according to a special format which briefly presents the project title, technical approach, development status, application of the technology, reactor type, power output, and organization which developed these designs. Part 1 and 2 cover water cooled reactors, liquid metal fast reactors, gas-cooled reactors and molten salt reactors. Subcritical accelerator-driven systems are also considered. Various reactor applications as power production, heat generation, ship propulsion, space power sources and transmutation of such waste are included. Each project is described within a few pages with the main features of an actual design using a table with main technical data and figure as well as references for additional information. Each chapter starts with an introduction which briefly describes main trends and approaches in this field. Explanations of terms and abbreviations are provided in a glossary.

  19. Neutron imaging on the VR-1 reactor

    Science.gov (United States)

    Crha, J.; Sklenka, L.; Soltes, J.

    2016-09-01

    Training reactor VR-1 is a low power research reactor with maximal thermal power of 1 kW. The reactor is operated by the Faculty of Nuclear Science and Physical Engineering of the Czech Technical University in Prague. Due to its low power it suits as a tool for education of university students and training of professionals. In 2015, as part of student research project, neutron imaging was introduced as another type of reactor utilization. The low available neutron flux and the limiting spatial and construction capabilities of the reactor's radial channel led to the development of a special filter/collimator insertion inside the channel and choosing a nonstandard approach by placing a neutron imaging plate inside the channel. The paper describes preliminary experiments carried out on the VR-1 reactor which led to first radiographic images. It seems, that due to the reactor construction and low reactor power, the neutron imaging technique on the VR-1 reactor is feasible mainly for demonstration or educational and training purposes.

  20. Supercritical-pressure light water cooled reactors

    CERN Document Server

    Oka, Yoshiaki

    2014-01-01

    This book focuses on the latest reactor concepts, single pass core and experimental findings in thermal hydraulics, materials, corrosion, and water chemistry. It highlights research on supercritical-pressure light water cooled reactors (SCWRs), one of the Generation IV reactors that are studied around the world. This book includes cladding material development and experimental findings on heat transfer, corrosion and water chemistry. The work presented here will help readers to understand the fundamental elements of reactor design and analysis methods, thermal hydraulics, materials and water

  1. BOILING SLURRY REACTOR AND METHOD FO CONTROL

    Science.gov (United States)

    Petrick, M.; Marchaterre, J.F.

    1963-05-01

    The control of a boiling slurry nuclear reactor is described. The reactor consists of a vertical tube having an enlarged portion, a steam drum at the top of the vertical tube, and at least one downcomer connecting the steam drum and the bottom of the vertical tube, the reactor being filled with a slurry of fissionabie material in water of such concentration that the enlarged portion of the vertical tube contains a critical mass. The slurry boils in the vertical tube and circulates upwardly therein and downwardly in the downcomer. To control the reactor by controlling the circulation of the slurry, a gas is introduced into the downcomer. (AEC)

  2. Sodium fast reactors with closed fuel cycle

    CERN Document Server

    Raj, Baldev; Vasudeva Rao, PR 0

    2015-01-01

    Sodium Fast Reactors with Closed Fuel Cycle delivers a detailed discussion of an important technology that is being harnessed for commercial energy production in many parts of the world. Presenting the state of the art of sodium-cooled fast reactors with closed fuel cycles, this book:Offers in-depth coverage of reactor physics, materials, design, safety analysis, validations, engineering, construction, and commissioning aspectsFeatures a special chapter on allied sciences to highlight advanced reactor core materials, specialized manufacturing technologies, chemical sensors, in-service inspecti

  3. Microchannel Methanation Reactors Using Nanofabricated Catalysts Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Makel Engineering, Inc. (MEI) and the Pennsylvania State University (Penn State) propose to develop and demonstrate a microchannel methanation reactor based on...

  4. Phosphorus removal in aerated stirred tank reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ghigliazza, R.; Lodi, A.; Rovatti, M. [Inst. of Chemical and Process Engineering ``G.B. Bonino``, Univ. of Genoa (Italy)

    1999-03-01

    The possibility to obtain biological phosphorus removal in strictly aerobic conditions has been investigated. Experiments, carried out in a continuous stirred tank reactor (CSTR), show the feasibility to obtain phosphorus removal without the anaerobic phase. Reactor performance in terms of phosphorus abatement kept always higher then 65% depending on adopted sludge retention time (SRT). In fact increasing SRT from 5 days to 8 days phosphorus removal and reactor performance increase but overcoming this SRT value a decreasing in reactor efficiency was recorded. (orig.) With 6 figs., 3 tabs., 18 refs.

  5. Savannah River Site reactor safety assessment. Draft

    Energy Technology Data Exchange (ETDEWEB)

    Woody, N.D.; Brandyberry, M.D. [eds.] [Westinghouse Savannah River Co., Aiken, SC (United States); Baker, W.H.; Brandyberry, M.D.; Kearnaghan, D.P.; O`Kula, K.R.; Woody, N.D. [Westinghouse Savannah River Co., Aiken, SC (United States); Amos, C.N.; Weingardt, J.J. [Science Applications International Corp., San Diego, CA (United States)

    1991-02-28

    This report gives the results of a Savannah River Site (SRS) Production Reactor risk assessment. Measures of adverse consequences to health and safety resulting from representations of severe accidents in SRS reactors are presented. In addition, the report gives a summary of the methods employed to represent these accidents and to assess the resultant consequences. The report is issued to provide timely information to the US Department of Energy (DOE) on the risk of operation of SRS reactors, for insights into severe accident phenomena that contribute to this risk, and in support of improved bases for other Site programs in Heavy Water Reactor safety.

  6. History of fast reactor fuel development

    Energy Technology Data Exchange (ETDEWEB)

    Kittel, J.H.; Frost, B.R.T. (Argonne National Lab., IL (United States)); Mustelier, J.P. (COGEMA, Velizy-Villacoublay (France))

    1992-01-01

    Most of the first generation of fast reactors that were operated at significant power levels employed solid metal fuels. They were constructed in the United States and United Kingdom in the 1950s and included Experimental Breeder Reactor (EBR)-I and -II operated by Argonne National Laboratory, United States, the Enrico Fermi Reactor operated by the Atomic Power Development Associates, United States and DFR operated by the U.K. Atomic Energy Authority (UKAEA). Their paper tracer pre-development of fast reactor fuel from these early days through the 1980s including ceramic fuels.

  7. Plant maintenance and advanced reactors, 2006

    Energy Technology Data Exchange (ETDEWEB)

    Agnihotri, Newal (ed.)

    2006-09-15

    The focus of the September-October issue is on plant maintenance and advanced reactors. Major articles/reports in this issue include: Advanced plants to meet rising expectations, by John Cleveland, International Atomic Energy Agency, Vienna; A flexible and economic small reactor, by Mario D. Carelli and Bojan Petrovic, Westinghouse Electric Company; A simple and passively safe reactor, by Yury N. Kuznetsov, Research and Development Institute of Power Engineering (NIKIET), Russia; Gas-cooled reactors, by Jeffrey S. Merrifield, U.S. Nuclear Regulatory Commission; ISI project managment in the PRC, by Chen Chanbing, RINPO, China; and, Fort Calhoun refurbishment, by Sudesh Cambhir, Omaha Public Power District.

  8. Usage of burnable poison on research reactors

    Energy Technology Data Exchange (ETDEWEB)

    Villarino, Eduardo Anibal [INVAP S.E., San Carlos de Bariloche (Argentina)

    2002-07-01

    The fuel assemblies with burnable poison are widely used on power reactors, but there are not commonly used on research reactors. This paper shows a neutronic analysis of the advantages and disadvantages of the burnable poison usage on research reactors. This paper analyses both burnable poison design used on research reactors: Boron on the lateral wall and Cadmium wires. Both designs include a parametric study on the design parameters like the amount and geometry of the burnable poison. This paper presents the design flexibility using burnable poisons, it does not find an optimal or final design, which it will strongly depend on the core characteristics and fuel management strategy. (author)

  9. Autonomous Control of Space Nuclear Reactors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Nuclear reactors to support future robotic and manned missions impose new and innovative technological requirements for their control and protection instrumentation....

  10. Continuous steroid biotransformations in microchannel reactors.

    Science.gov (United States)

    Marques, Marco P C; Fernandes, Pedro; Cabral, Joaquim M S; Znidaršič-Plazl, Polona; Plazl, Igor

    2012-01-15

    The use of microchannel reactor based technologies within the scope of bioprocesses as process intensification and production platforms is gaining momentum. Such trend can be ascribed a particular set of characteristics of microchannel reactors, namely the enhanced mass and heat transfer, combined with easier handling and smaller volumes required, as compared to traditional reactors. In the present work, a continuous production process of 4-cholesten-3-one by the enzymatic oxidation of cholesterol without the formation of any by-product was assessed. The production was carried out within Y-shaped microchannel reactors in an aqueous-organic two-phase system. Substrate was delivered from the organic phase to aqueous phase containing cholesterol oxidase and the product formed partitions back to the organic phase. The aqueous phase was then forced through a plug-flow reactor, containing immobilized catalase. This step aimed at the reduction of hydrogen peroxide formed as a by-product during cholesterol oxidation, to avoid cholesterol oxidase deactivation due to said by-product. This setup was compared with traditional reactors and modes of operation. The results showed that microchannel reactor geometry outperformed traditional stirred tank and plug-flow reactors reaching similar conversion yields at reduced residence time. Coupling the plug-flow reactor containing catalase enabled aqueous phase reuse with maintenance of 30% catalytic activity of cholesterol oxidase while eliminating hydrogen peroxide. A final production of 36 m of cholestenone was reached after 300 hours of operation.

  11. Spheromak reactor-design study

    Energy Technology Data Exchange (ETDEWEB)

    Les, J.M.

    1981-06-30

    A general overview of spheromak reactor characteristics, such as MHD stability, start up, and plasma geometry is presented. In addition, comparisons are made between spheromaks, tokamaks and field reversed mirrors. The computer code Sphero is also discussed. Sphero is a zero dimensional time independent transport code that uses particle confinement times and profile parameters as input since they are not known with certainty at the present time. More specifically, Sphero numerically solves a given set of transport equations whose solutions include such variables as fuel ion (deuterium and tritium) density, electron density, alpha particle density and ion, electron temperatures.

  12. Reactors for nuclear electric propulsion

    Energy Technology Data Exchange (ETDEWEB)

    Buden, D.; Angelo, J.A. Jr.

    1981-01-01

    Propulsion is the key to space exploitation and power is the key to propulsion. This paper examines the role of nuclear fission reactors as the primary power source for high specific impulse electric propulsion systems for space missions of the 1980s and 1990s. Particular mission applications include transfer to and a reusable orbital transfer vehicle from low-Earth orbit to geosynchronous orbit, outer planet exploration and reconnaissance missions, and as a versatile space tug supporting lunar resource development. Nuclear electric propulsion is examined as an indispensable component in space activities of the next two decades.

  13. K-East and K-West Reactors

    Data.gov (United States)

    Federal Laboratory Consortium — Hanford's "sister reactors", the K-East and the K-West Reactors, were built side-by-side in the early 1950's. The two reactors went operational within four months of...

  14. Research on plasma core reactors

    Energy Technology Data Exchange (ETDEWEB)

    Jarvis, G.A.; Barton, D.M.; Helmick, H.H.; Bernard, W.; White, R.H.

    1977-01-01

    Experiments and theoretical studies are being conducted for NASA on critical assemblies with 1-m-diam by 1-m-long low-density cores surrounded by a thick beryllium reflector. These assemblies make extensive use of existing nuclear propulsion reactor components, facilities, and instrumentation. Due to excessive porosity in the reflector, the initial critical mass was 19 kg U(93.2). Addition of a 17-cm-thick by 89-cm-diam beryllium flux trap in the cavity reduced the critical mass to 7 kg when all the uranium was in the zone just outside the flux trap. A mockup aluminum UF/sub 6/ container was placed inside the flux trap and fueled with uranium-graphite elements. Fission distributions and reactivity worths of fuel and structural materials were measured. Finally, an 85,000-cm/sup 3/ aluminum canister in the central region was fueled with UF/sub 6/ gas and fission density distributions determined. These results will be used to guide the design of a prototype plasma core reactor which will test energy removal by optical radiation.

  15. Compound cryopump for fusion reactors

    CERN Document Server

    Kovari, M; Shephard, T

    2013-01-01

    We reconsider an old idea: a three-stage compound cryopump for use in fusion reactors such as DEMO. The helium "ash" is adsorbed on a 4.5 K charcoal-coated surface, while deuterium and tritium are adsorbed at 15-22 K on a second charcoal-coated surface. The helium is released by raising the first surface to ~30 K. In a separate regeneration step, deuterium and tritium are released at ~110 K. In this way, the helium can be pre-separated from other species. In the simplest design, all three stages are in the same vessel, with a single valve to close the pump off from the tokamak during regeneration. In an alternative design, the three stages are in separate vessels, connected by valves, allowing the stages to regenerate without interfering with each other. The inclusion of the intermediate stage would not affect the overall pumping speed significantly. The downstream exhaust processing system could be scaled down, as much of the deuterium and tritium could be returned directly to the reactor. This could reduce ...

  16. Dissecting Reactor Antineutrino Flux Calculations

    Science.gov (United States)

    Sonzogni, A. A.; McCutchan, E. A.; Hayes, A. C.

    2017-09-01

    Current predictions for the antineutrino yield and spectra from a nuclear reactor rely on the experimental electron spectra from 235U, 239Pu, 241Pu and a numerical method to convert these aggregate electron spectra into their corresponding antineutrino ones. In the present work we investigate quantitatively some of the basic assumptions and approximations used in the conversion method, studying first the compatibility between two recent approaches for calculating electron and antineutrino spectra. We then explore different possibilities for the disagreement between the measured Daya Bay and the Huber-Mueller antineutrino spectra, including the 238U contribution as well as the effective charge and the allowed shape assumption used in the conversion method. We observe that including a shape correction of about +6 % MeV-1 in conversion calculations can better describe the Daya Bay spectrum. Because of a lack of experimental data, this correction cannot be ruled out, concluding that in order to confirm the existence of the reactor neutrino anomaly, or even quantify it, precisely measured electron spectra for about 50 relevant fission products are needed. With the advent of new rare ion facilities, the measurement of shape factors for these nuclides, for many of which precise beta intensity data from TAGS experiments already exist, would be highly desirable.

  17. A new MTR fuel for a new MTR reactor: UMo for the Jules Horowitz reactor

    Energy Technology Data Exchange (ETDEWEB)

    Guigon, B. [CEA Cadarache, Dir. de l' Energie Nucleaire DEN, Reacteur Jules Horowitz, 13 - Saint-Paul-lez-Durance (France); Vacelet, H. [Compagnie pour l' Etude et la Realisation de Combustibles Atomiques, CERCA, Etablissement de Romans, 26 (France); Dornbusch, D. [Technicatome, Service d' Architecture Generale, 13 - Aix-en-Provence (France)

    2003-07-01

    Within some years, the Jules Horowitz Reactor will be the only working experimental reactor (material and fuel testing reactor) in France. It will have to provide facilities for a wide range of needs: from activation analysis to power reactor fuel qualification. In this paper will be presented the main characteristics of the Jules Horowitz Reactor: its total power, neutron flux, fuel element... Safety criteria will be explained. Finally merits and disadvantages of UMo compared to the standard U{sub 3}Si{sub 2} fuel will be discussed. (authors)

  18. Annual report on JEN-1 reactor; Informe periodico del Reactor JEN-1 correspondiente al ano 1971

    Energy Technology Data Exchange (ETDEWEB)

    Montes, J.

    1972-07-01

    In the annual report on the JEN-1 reactor the main features of the reactor operations and maintenance are described. The reactor has been critical for 1831 hours, what means 65,8% of the total working time. Maintenance and pool water contamination have occupied the rest of the time. The maintenance schedule is shown in detail according to three subjects. The main failures and reactor scrams are also described. The daily maximum values of the water activity are given so as the activity of the air in the reactor hall. (Author)

  19. Mathematical Modeling for Simulation of Nuclear Reactor Analysis

    OpenAIRE

    Salah Ud-Din Khan; Shahab Ud-Din Khan

    2013-01-01

    In this paper, we have developed a mathematical model for the nuclear reactor analysis to be implemented in the nuclear reactor code. THEATRe is nuclear reactor analysis code which can only work for the cylindrical type fuel reactor and cannot applicable for the plate type fuel nuclear reactor. Therefore, the current studies encompasses on the modification of THEATRe code for the plate type fuel element. This mathematical model is applicable to the thermal analysis of the reactor which is ver...

  20. Parametric sensitivity and runaway in tubular reactors

    Energy Technology Data Exchange (ETDEWEB)

    Morbidelli, M.; Varma, A.

    1982-09-01

    Parametric sensitivity of tubular reactors is analyzed to provide critical values of the heat of reaction and heat transfer parameters defining runaway and stable operations for all positive-order exothermic reactions with finite activation energies, and for all reactor inlet temperatures. Evaluation of the critical values does not involve any trial and error.

  1. Design of an organic simplified nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Shirvan, Koroush [Dept. of Nuclear Science and Engineering, Massachusetts Institute of Technology, Cambridge (United States); Forrest, Eric [Primary Standards Laboratory, Sandia National Laboratories, Albuquerque (United States)

    2016-08-15

    Numerous advanced reactor concepts have been proposed to replace light water reactors ever since their establishment as the dominant technology for nuclear energy production. While most designs seek to improve cost competitiveness and safety, the implausibility of doing so with affordable materials or existing nuclear fuel infrastructure reduces the possibility of near-term deployment, especially in developing countries. The organic nuclear concept, first explored in the 1950s, offers an attractive alternative to advanced reactor designs being considered. The advent of high temperature fluids, along with advances in hydrocracking and reforming technologies driven by the oil and gas industries, make the organic concept even more viable today. We present a simple, cost-effective, and safe small modular nuclear reactor for offshore underwater deployment. The core is moderated by graphite, zirconium hydride, and organic fluid while cooled by the organic fluid. The organic coolant enables operation near atmospheric pressure and use of plain carbon steel for the reactor tank and primary coolant piping system. The core is designed to mitigate the coolant degradation seen in early organic reactors. Overall, the design provides a power density of 40 kW/L, while reducing the reactor hull size by 40% compared with a pressurized water reactor while significantly reducing capital plant costs.

  2. Helix reactor: great potential for flow chemistry

    NARCIS (Netherlands)

    Geerdink, P.; Runstraat, A. van den; Roelands, C.P.M.; Goetheer, E.L.V.

    2009-01-01

    The Helix reactor is highly suited for precise reaction control based on good hydrodynamics. The hydrodynamics are controlled by the Dean vortices, which create excellent heat transfer properties, approach plug flow and avoid turbulence. The flexibility of this reactor has been demonstrated using a

  3. Startup of an industrial adiabatic tubular reactor

    NARCIS (Netherlands)

    Verwijs, J.W.; Berg, van den H.; Westerterp, K.R.

    1992-01-01

    The dynamic behaviour of an adiabatic tubular plant reactor during the startup is demonstrated, together with the impact of a feed-pump failure of one of the reactants. A dynamic model of the reactor system is presented, and the system response is calculated as a function of experimentally-determine

  4. Rotor for a pyrolysis centrifuge reactor

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a rotor for a pyrolysis centrifuge reactor, said rotor comprising a rotor body having a longitudinal centre axis, and at least one pivotally mounted blade being adapted to pivot around a pivot axis under rotation of the rotor body around the longitudinal centre axis....... Moreover, the present invention relates to a pyrolysis centrifuge reactor applying such a rotor....

  5. Technical features of the MR reactor decommissioning

    Directory of Open Access Journals (Sweden)

    Craig David

    2008-01-01

    Full Text Available This paper presents a preliminary technical design for the dismantling of the MR reactor. The goal of the design is the removal of reactor components allowing the re-use of the building for a different nuclear related purpose. The sequence of segmentation procedures is established. Considerations on the size reduction and tooling are presented.

  6. University of Virginia Reactor Facility Decommissioning Results

    Energy Technology Data Exchange (ETDEWEB)

    Ervin, P. F.; Lundberg, L. A.; Benneche, P. E.; Mulder, R. U.; Steva, D. P.

    2003-02-24

    The University of Virginia Reactor Facility started accelerated decommissioning in 2002. The facility consists of two licensed reactors, the CAVALIER and the UVAR. This paper will describe the progress in 2002, remaining efforts and the unique organizational structure of the project team.

  7. Advanced tokamak concepts and reactor designs

    NARCIS (Netherlands)

    Oomens, A. A. M.

    2000-01-01

    From a discussion of fusion reactor designs based on today's well-established experience gained in the operation of large tokamaks, it is concluded that such reactors are economically not attractive. The physics involved in the various options for concept improvement is described, some examples

  8. The Design of a Nuclear Reactor

    Indian Academy of Sciences (India)

    2016-09-01

    The aim of this largely pedagogical article is toemploy pre-college physics to arrive at an understanding of a system as complex as a nuclear reactor. We focus on three key issues: the fuelpin, the moderator, and lastly the dimensions ofthe nuclear reactor.

  9. MODERATOR ELEMENTS FOR UNIFORM POWER NUCLEAR REACTOR

    Science.gov (United States)

    Balent, R.

    1963-03-12

    This patent describes a method of obtaining a flatter flux and more uniform power generation across the core of a nuclear reactor. The method comprises using moderator elements having differing moderating strength. The elements have an increasing amount of the better moderating material as a function of radial and/or axial distance from the reactor core center. (AEC)

  10. Selective purge for hydrogenation reactor recycle loop

    Science.gov (United States)

    Baker, Richard W.; Lokhandwala, Kaaeid A.

    2001-01-01

    Processes and apparatus for providing improved contaminant removal and hydrogen recovery in hydrogenation reactors, particularly in refineries and petrochemical plants. The improved contaminant removal is achieved by selective purging, by passing gases in the hydrogenation reactor recycle loop or purge stream across membranes selective in favor of the contaminant over hydrogen.

  11. The First Reactor, 40th Anniversary (rev.)

    Energy Technology Data Exchange (ETDEWEB)

    Allardice, Corbin; Trapnell, Edward R; Fermi, Enrico; Fermi, Laura; Williams, Robert C

    1982-12-01

    This booklet, an updated version of the original booklet describing the first nuclear reactor, was written in honor of the 40th anniversary of the first reactor or "pile". It is based on firsthand accounts told to Corbin Allardice and Edward R. Trapnell, and includes recollections of Enrico and Laura Fermi.

  12. The First Reactor, 40th Anniversary (rev.)

    Energy Technology Data Exchange (ETDEWEB)

    Allardice, Corbin; Trapnell, Edward R; Fermi, Enrico; Fermi, Laura; Williams, Robert C

    1982-12-01

    This booklet, an updated version of the original booklet describing the first nuclear reactor, was written in honor of the 40th anniversary of the first reactor or "pile". It is based on firsthand accounts told to Corbin Allardice and Edward R. Trapnell, and includes recollections of Enrico and Laura Fermi.

  13. Radiochemical problems of fusion reactors. 1. Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Crespi, M.B.A.

    1984-02-01

    A list of fusion reactor candidate materials is given, for use in connection with blanket structure, breeding, moderation, neutron multiplication, cooling, magnetic field generation, electrical insulation and radiation shielding. The phenomena being studied for each group of materials are indicated. Suitable irradiation test facilities are discussed under the headings (1) accelerator-based neutron sources, (2) fission reactors, and (3) ion accelerators.

  14. Nuclear data requirements for fusion reactor nucleonics

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, M.R.; Abdou, M.A.

    1980-01-01

    Nuclear data requirements for fusion reactor nucleonics are reviewed and the present status of data are assessed. The discussion is divided into broad categories dealing with data for Fusion Materials Irradiation Test Facility (FMIT), D-T Fusion Reactors, Alternate Fuel Cycles and the Evaluated Data Files that are available or would be available in the near future.

  15. Design of an Organic Simplified Nuclear Reactor

    Directory of Open Access Journals (Sweden)

    Koroush Shirvan

    2016-08-01

    Full Text Available Numerous advanced reactor concepts have been proposed to replace light water reactors ever since their establishment as the dominant technology for nuclear energy production. While most designs seek to improve cost competitiveness and safety, the implausibility of doing so with affordable materials or existing nuclear fuel infrastructure reduces the possibility of near-term deployment, especially in developing countries. The organic nuclear concept, first explored in the 1950s, offers an attractive alternative to advanced reactor designs being considered. The advent of high temperature fluids, along with advances in hydrocracking and reforming technologies driven by the oil and gas industries, make the organic concept even more viable today. We present a simple, cost-effective, and safe small modular nuclear reactor for offshore underwater deployment. The core is moderated by graphite, zirconium hydride, and organic fluid while cooled by the organic fluid. The organic coolant enables operation near atmospheric pressure and use of plain carbon steel for the reactor tank and primary coolant piping system. The core is designed to mitigate the coolant degradation seen in early organic reactors. Overall, the design provides a power density of 40 kW/L, while reducing the reactor hull size by 40% compared with a pressurized water reactor while significantly reducing capital plant costs.

  16. Naval reactors physics handbook. Volume 3: The physics of intermediate spectrum reactors

    Energy Technology Data Exchange (ETDEWEB)

    Stehn, J.R. [ed.] [Knolls Atomic Power Lab., Schenectady, NY (United States)

    1958-09-01

    The present volume has been prepared for persons with some knowledge of the physics of nuclear reactors. It is intended to make available the accumulated physics experience of the Knolls Atomic Power Laboratory in its work on intermediate spectrum reactors. Only those portions have been selected which were deemed to be most useful and significant to other physicists concerned with the problems of reactor design. The volume is divided into four parts which are more or less independent of one another. Part 1 (Chaps. 2--9), Investigation of Reactor Characteristics by Critical Assemblies, reflects the importance of the properties of critical assemblies and of the techniques for obtaining experimental information about such assemblies. Part 2 (Chaps. 10--20), Reactivity Effects Associated with Reactor Operation, details the use of both critical assemblies and reactor theory to make and test predictions of the manner in which the reactivity of an intermediate power reactor will vary during operation. Part 3 (Chaps. 21--26), Heat Generation and Nuclear Materials Problems, considers how reactor heat generation is spread out in space and time, and what nuclear effects result from the presence of beryllium or sodium in the reactor. Part 4 (Chaps. 27--38), Reactor Kinetics and Temperature Coefficients, relates to the transient or near-transient behavior of intermediate reactors.

  17. State space modeling of reactor core in a pressurized water reactor

    Science.gov (United States)

    Ashaari, A.; Ahmad, T.; Shamsuddin, Mustaffa; M, Wan Munirah W.; Abdullah, M. Adib

    2014-07-01

    The power control system of a nuclear reactor is the key system that ensures a safe operation for a nuclear power plant. However, a mathematical model of a nuclear power plant is in the form of nonlinear process and time dependent that give very hard to be described. One of the important components of a Pressurized Water Reactor is the Reactor core. The aim of this study is to analyze the performance of power produced from a reactor core using temperature of the moderator as an input. Mathematical representation of the state space model of the reactor core control system is presented and analyzed in this paper. The data and parameters are taken from a real time VVER-type Pressurized Water Reactor and will be verified using Matlab and Simulink. Based on the simulation conducted, the results show that the temperature of the moderator plays an important role in determining the power of reactor core.

  18. State space modeling of reactor core in a pressurized water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ashaari, A.; Ahmad, T.; M, Wan Munirah W. [Department of Mathematical Science, Faculty of Science, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Shamsuddin, Mustaffa [Institute of Ibnu Sina, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Abdullah, M. Adib [Swinburne University of Technology, Faculty of Engineering, Computing and Science, Jalan Simpang Tiga, 93350 Kuching, Sarawak (Malaysia)

    2014-07-10

    The power control system of a nuclear reactor is the key system that ensures a safe operation for a nuclear power plant. However, a mathematical model of a nuclear power plant is in the form of nonlinear process and time dependent that give very hard to be described. One of the important components of a Pressurized Water Reactor is the Reactor core. The aim of this study is to analyze the performance of power produced from a reactor core using temperature of the moderator as an input. Mathematical representation of the state space model of the reactor core control system is presented and analyzed in this paper. The data and parameters are taken from a real time VVER-type Pressurized Water Reactor and will be verified using Matlab and Simulink. Based on the simulation conducted, the results show that the temperature of the moderator plays an important role in determining the power of reactor core.

  19. Verification of Remote Inspection Techniques for Reactor Internal Structures of Liquid Metal Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Joo, Young Sang; Lee, Jae Han

    2007-02-15

    The reactor internal structures and components of a liquid metal reactor (LMR) are submerged in hot sodium of reactor vessel. The division 3 of ASME code section XI specifies the visual inspection as major in-service inspection (ISI) methods of reactor internal structures and components. Reactor internals of LMR can not be visually examined due to opaque liquid sodium. The under-sodium viewing techniques using an ultrasonic wave should be applied for the visual inspection of reactor internals. Recently, an ultrasonic waveguide sensor with a strip plate has been developed for an application to the under-sodium inspection. In this study, visualization technique, ranging technique and monitoring technique have been suggested for the remote inspection of reactor internals by using the waveguide sensor. The feasibility of these remote inspection techniques using ultrasonic waveguide sensor has been evaluated by an experimental verification.

  20. Verification of Remote Inspection Techniques for Reactor Internal Structures of Liquid Metal Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Joo, Young Sang; Lee, Jae Han

    2007-02-15

    The reactor internal structures and components of a liquid metal reactor (LMR) are submerged in hot sodium of reactor vessel. The division 3 of ASME code section XI specifies the visual inspection as major in-service inspection (ISI) methods of reactor internal structures and components. Reactor internals of LMR can not be visually examined due to opaque liquid sodium. The under-sodium viewing techniques using an ultrasonic wave should be applied for the visual inspection of reactor internals. Recently, an ultrasonic waveguide sensor with a strip plate has been developed for an application to the under-sodium inspection. In this study, visualization technique, ranging technique and monitoring technique have been suggested for the remote inspection of reactor internals by using the waveguide sensor. The feasibility of these remote inspection techniques using ultrasonic waveguide sensor has been evaluated by an experimental verification.

  1. Scanning tunneling microscope assembly, reactor, and system

    Science.gov (United States)

    Tao, Feng; Salmeron, Miquel; Somorjai, Gabor A

    2014-11-18

    An embodiment of a scanning tunneling microscope (STM) reactor includes a pressure vessel, an STM assembly, and three spring coupling objects. The pressure vessel includes a sealable port, an interior, and an exterior. An embodiment of an STM system includes a vacuum chamber, an STM reactor, and three springs. The three springs couple the STM reactor to the vacuum chamber and are operable to suspend the scanning tunneling microscope reactor within the interior of the vacuum chamber during operation of the STM reactor. An embodiment of an STM assembly includes a coarse displacement arrangement, a piezoelectric fine displacement scanning tube coupled to the coarse displacement arrangement, and a receiver. The piezoelectric fine displacement scanning tube is coupled to the coarse displacement arrangement. The receiver is coupled to the piezoelectric scanning tube and is operable to receive a tip holder, and the tip holder is operable to receive a tip.

  2. Dynamic model of Fast Breeder Test Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Vaidyanathan, G., E-mail: vaidya@igcar.gov.i [Fast Reactor Technology Group, Indira Gandhi Center for Atomic Research, Kalpakkam (India); Kasinathan, N.; Velusamy, K. [Fast Reactor Technology Group, Indira Gandhi Center for Atomic Research, Kalpakkam (India)

    2010-04-15

    Fast Breeder Test Reactor (FBTR) is a 40 M Wt/13.2 MWe sodium cooled reactor operating since 1985. It is a loop type reactor. As part of the safety analysis the response of the plant to various transients is needed. In this connection a computer code named DYNAM was developed to model the reactor core, the intermediate heat exchanger, steam generator, piping, etc. This paper deals with the mathematical model of the various components of FBTR, the numerical techniques to solve the model, and comparison of the predictions of the code with plant measurements. Also presented is the benign response of the plant to a station blackout condition, which brings out the role of the various reactivity feedback mechanisms combined with a gradual coast down of reactor sodium flow.

  3. Reactivity control assembly for nuclear reactor. [LMFBR

    Science.gov (United States)

    Bollinger, L.R.

    1982-03-17

    This invention, which resulted from a contact with the United States Department of Energy, relates to a control mechanism for a nuclear reactor and, more particularly, to an assembly for selectively shifting different numbers of reactivity modifying rods into and out of the core of a nuclear reactor. It has been proposed heretofore to control the reactivity of a breeder reactor by varying the depth of insertion of control rods (e.g., rods containing a fertile material such as ThO/sub 2/) in the core of the reactor, thereby varying the amount of neutron-thermalizing coolant and the amount of neutron-capturing material in the core. This invention relates to a mechanism which can advantageously be used in this type of reactor control system.

  4. Power Control Method for Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Baang, Dane; Suh, Yongsuk; Park, Cheol [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Considering safety-oriented design concept and other control environment, we developed a simple controller that provides limiting function of power change- rate as well as fine tracking performance. The design result has been well-proven via simulation and actual application to a TRIGA-II type research reactor. The proposed controller is designed to track the PDM(Power Demand) from operator input as long as maintaining the power change rate lower than a certain value for stable reactor operation. A power control method for a TRIGA-II type research reactor has been designed, simulated, and applied to actual reactor. The control performance during commissioning test shows that the proposed controller provides fine control performance for various changes in reference values (PDM), even though there is large measurement noise from neutron detectors. The overshoot at low power level is acceptable in a sense of reactor operation.

  5. Precision spectroscopy with reactor anti-neutrinos

    CERN Document Server

    Huber, P; Huber, Patrick; Schwetz, Thomas

    2004-01-01

    In this work we present an accurate parameterization of the anti-neutrino flux produced by the isotopes 235U, 239Pu and 241Pu in nuclear reactors. We determine the coefficients of this parameterization, as well as their covariance matrix, by performing a fit to spectra inferred from experimentally measured beta spectra. Subsequently we show that flux shape uncertainties play only a minor role in the KamLAND experiment, however, we find that future reactor neutrino experiments to measure the mixing angle $\\theta_{13}$ are sensitive to the fine details of the reactor neutrino spectra. Finally, we investigate the possibility to determine the isotopic composition in nuclear reactors through an anti-neutrino measurement. We find that with a 3 month exposure of a one ton detector the isotope fractions and the thermal reactor power can be determined at a few percent accuracy, which may open the possibility of an application for safeguard or non-proliferation objectives.

  6. Reactor assessments of advanced bumpy torus configurations

    Energy Technology Data Exchange (ETDEWEB)

    Uckan, N.A.; Owen, L.W.; Spong, D.A.; Miller, R.L.; Ard, W.B.; Pipkins, J.F.; Schmitt, R.J.

    1984-02-01

    Recently, several innovative approaches were introduced for enhancing the performance of the basic ELMO Bumpy Torus (EBT) concept and for improving its reactor potential. These include planar racetrack and square geometries, Andreoletti coil systems, and bumpy torus-stellarator hybrids (which include twisted racetrack and helical axis stellarator - snakey torus). Preliminary evaluations of reactor implications of each approach have been carried out based on magnetics (vacuum) calculations, transport and scaling relationships, and stability properties deduced from provisional configurations that implement the approach but are not necessarily optimized. Further optimization is needed in all cases to evaluate the full potential of each approach. Results of these studies indicate favorable reactor projections with a significant reduction in reactor physical size as compared to conventional EBT reactor designs carried out in the past.

  7. Testing commercial catalysts in recycle reactors

    Energy Technology Data Exchange (ETDEWEB)

    Berty, J.M.

    1979-01-01

    Recycle reactors for quality control of catalyst production and for testing new catalysts for known or new processes have the following advantages over tubular reactors: they can reproduce the physical and chemical regime which surrounds the catalyst in a commercial reactor; they can achieve high mass and heat transfer; they exhibit uniform coke deposit; and they provide independence of mass velocity and space velocity. Their disadvantage is the unconventional specification of experiments in terms of discharge concentration which derives from the implicit nature of the basic mathematical relationships. Recycle reactor test methods are outlined for quality control and for testing catalysts, e.g., supported nickel from different manufacturers, for processes whose chemistry is well known. Approaches for testing catalysts for new processes are discussed. The standard recycle reactor developed at Union Carbide Corp. and manufactured by Autoclave Engineers, and several of its modifications are described.

  8. Ceramic oxygen transport membrane array reactor and reforming method

    Science.gov (United States)

    Kelly, Sean M.; Christie, Gervase Maxwell; Robinson, Charles; Wilson, Jamie R.; Gonzalez, Javier E.; Doraswami, Uttam R.

    2016-11-08

    The invention relates to a commercially viable modular ceramic oxygen transport membrane reforming reactor configured using repeating assemblies of oxygen transport membrane tubes and catalytic reforming reactors.

  9. Ceramic oxygen transport membrane array reactor and reforming method

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Sean M.; Christie, Gervase Maxwell; Robinson, Charles; Wilson, Jamie R.; Gonzalez, Javier E.; Doraswami, Uttam R.

    2016-11-08

    The invention relates to a commercially viable modular ceramic oxygen transport membrane reforming reactor configured using repeating assemblies of oxygen transport membrane tubes and catalytic reforming reactors.

  10. Fast Spectrum Molten Salt Reactor Options

    Energy Technology Data Exchange (ETDEWEB)

    Gehin, Jess C [ORNL; Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Patton, Bruce W [ORNL; Howard, Rob L [ORNL; Harrison, Thomas J [ORNL

    2011-07-01

    During 2010, fast-spectrum molten-salt reactors (FS-MSRs) were selected as a transformational reactor concept for light-water reactor (LWR)-derived heavy actinide disposition by the Department of Energy-Nuclear Energy Advanced Reactor Concepts (ARC) program and were the subject of a preliminary scoping investigation. Much of the reactor description information presented in this report derives from the preliminary studies performed for the ARC project. This report, however, has a somewhat broader scope-providing a conceptual overview of the characteristics and design options for FS-MSRs. It does not present in-depth evaluation of any FS-MSR particular characteristic, but instead provides an overview of all of the major reactor system technologies and characteristics, including the technology developments since the end of major molten salt reactor (MSR) development efforts in the 1970s. This report first presents a historical overview of the FS-MSR technology and describes the innovative characteristics of an FS-MSR. Next, it provides an overview of possible reactor configurations. The following design features/options and performance considerations are described including: (1) reactor salt options-both chloride and fluoride salts; (2) the impact of changing the carrier salt and actinide concentration on conversion ratio; (3) the conversion ratio; (4) an overview of the fuel salt chemical processing; (5) potential power cycles and hydrogen production options; and (6) overview of the performance characteristics of FS-MSRs, including general comparative metrics with LWRs. The conceptual-level evaluation includes resource sustainability, proliferation resistance, economics, and safety. The report concludes with a description of the work necessary to begin more detailed evaluation of FS-MSRs as a realistic reactor and fuel cycle option.

  11. The research reactors their contribution to the reactors physics; Les reacteurs de recherche leur apport sur la physique des reacteurs

    Energy Technology Data Exchange (ETDEWEB)

    Barral, J.C. [Electricite de France (EDF), 75 - Paris (France); Zaetta, A. [CEA/Cadarache, Direction des Reacteurs Nucleaires, DRN, 13 - Saint-Paul-lez-Durance (France); Johner, J. [CEA/Cadarache, Dept. de Recherches sur la Fusion Controlee (DRFC), 13 - Saint Paul lez Durance (France); Mathoniere, G. [CEA/Saclay, DEN, 91 - Gif sur Yvette (France)] [and others

    2000-07-01

    The 19 october 2000, the french society of nuclear energy organized a day on the research reactors. This associated report of the technical session, reactors physics, is presented in two parts. The first part deals with the annual meeting and groups general papers on the pressurized water reactors, the fast neutrons reactors and the fusion reactors industry. The second part presents more technical papers about the research programs, critical models, irradiation reactors (OSIRIS and Jules Horowitz) and computing tools. (A.L.B.)

  12. Electromagnetic Environment Monitor and Analysis System Based on Quad-rotor UAV Platform%基于四旋翼无人机的电磁环境监测分析系统

    Institute of Scientific and Technical Information of China (English)

    贾语扬; 张凯; 卢小祝; 尚晓凡; 苏东林

    2016-01-01

    提出一套基于四旋翼无人机平台的电磁环境监测分析系统,通过将电磁环境监测硬件集成到四旋翼无人机平台上,使用自行开发的测量管理软件和电磁干扰源定位算法,可以实现对空间电磁环境的自动测量及测量数据实时分析处理.详细介绍测量管理软件的组成和基于电磁干扰源定位算法开发的电磁环境可视化软件.实验结果表明,基于四旋翼无人机平台的电磁环境监测分析系统自动化程度高,测量精度高,且显示直观.%An electromagnetic environment (EME) monitor and analysis system based on quad-rotor UAV platform is proposed. By integrating the EME monitoring hardware into quad-rotor UAV platform and utilizing self-developed measurement management software and electromagnetic interference source localization algorithm, the automatic measurement of space electromagnetic environment and real-time analysis of measurement data can be realized. The composition of measurement management software and the EME visualization software developed on the basis of electromagnetic interference source localization algorithm are introduced in detail. The experiment results show that this electromagnetic environment monitor and analysis system based on quad-rotor UAV platform has high degree of automation, high accuracy of measurement and visual display.

  13. Design and Measurement of Improved Quad-Ridged Orthomode Transducers%改进型四脊波导正交模转换器的设计与测量

    Institute of Scientific and Technical Information of China (English)

    庄重; 李斌; 范庆元

    2011-01-01

    A high performance quad-ridged orthomode transducer (OMT) with small size was designed based on the traditional quad-ridged OMT for C band receiver of shanghai 65m radio telescope.The structure and working principle of the improved OMT were introduced, main design outlines were analyzed, simulation results by both FEM and FIT methods were given and the tolerance of the OMT was analyzed.The prototype of the OMT was fabricated finally and the measurement resuits show that the improved quad-ridged OMT has small size, wide band and high performances.%为满足上海65m射电望远镜C波段接收机需求,在传统四脊波导OMT(Orthomode Transducer)基础上设计了一种小尺寸、高性能的宽带四脊波导正交模转换器.介绍了该OMT的结构和工作原理,讨论了设计要点,给出了有限元法(FEM)和时域有限积分法(FIT)的仿真结果,分析了OMT的容差性能,最后实际加工了实验样机.实验结果表明,改进型四脊波导OMT具有尺寸小、频带宽、高性能的特点,能够满足射电天文制冷接收机需求.

  14. Radiation protection at new reactors

    Energy Technology Data Exchange (ETDEWEB)

    Brissaud, A. [EDF INDUSTRY, Basic Design Department, EDF-SEPTEN, VILLEURBANNE Cedex (France)

    2000-05-01

    The theoritical knowledge and the feedback of operating experience concerning radiations in reactors is now considerable. It is available to the designer in the form of predictive softwares and data bases. Thus, it is possible to include the radiation protection component throughout all the design process. In France, the existing reactors have not been designed with quantified radiation protection targets, although considerable efforts have been made to reduce sources of radiation illustrated by the decrease of the average dose rates (typically a factor 5 between the first 900 MWe and the last 1300 MWe units). The EDF ALARA PROJECT has demonstrated that good practises, radiation protection awareness, careful work organization had a strong impact on operation and maintenance work volume. A decrease of the average collective dose by a factor 2 has been achieved without noticeable modifications of the units. In the case of new nuclear facilities projects (reactor, intermediate storage facility,...), or special operations (such as steam generator replacement), quantified radiation protection targets are included in terms of collective and average individual doses within the frame of a general optimization scheme. The target values by themselves are less important than the application of an optimization process throughout the design. This is because the optimization process requires to address all the components of the dose, particularly the work volume for operation and maintenance. A careful study of this parameter contributes to the economy of the project (suppression of unecessary tasks, time-saving ergonomy of work sites). This optimization process is currently applied to the design of the EPR. General radiation protection provisions have been addressed during the basic design phase by applying general rules aiming at the reduction of sources and dose rates. The basic design optimization phase has mainly dealt with the possibility to access the containment at full

  15. 某四旋翼无人飞行器的力学仿真分析%Mechanical Simulation Analysis of a Quad-rotor Unmanned Aerial Vehicle

    Institute of Scientific and Technical Information of China (English)

    吴文志; 吴斌; 周星; 张平; 程林

    2016-01-01

    旋翼无人飞行器具有垂直起降/着陆、可悬停、机动性好及结构简单等多种优点,无论是在军事领域还是民用领域,都有非常广泛的应用价值。文中采用Abaqus建立了某四旋翼无人飞行器的力学仿真模型。基于所建立的力学仿真模型,分析了该无人飞行器在旋翼升力、风载荷和降落冲击等工况下结构的强度和刚度响应,得到了相应的变形和应力云图。计算结果表明,该旋翼飞行器的结构设计满足总体设计要求。%Rotor unmanned aerial vehicle ( UAV) has wide applications in military and civil fields due to its merits such as vertical taking off and landing, hovering ability, good maneuverability and simplified structure . In this paper the mechanical simulation model of a quad-rotor UAV is established .Based on the model , the strength and stiffness responses of the UAV structure under the conditions of rotor lift , wind load and landing impact are analyzed and the corresponding contours of deformation and stress are obtained .The results show that the structure design of this UAV satisfies the requirements of system design .

  16. Membrane reactor technology for ultrapure hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Patil, C.S.

    2005-11-17

    The main objectives of this thesis are (1) to compare different reactor types and assess the feasibility of operation; (2) to develop and design a novel reactor concept based on the integration of perm-selective hydrogen and oxygen membranes; and (3) to give an experimental proof of principle of the developed reactor concept. In Chapter 2, available perm-selective hydrogen and oxygen membranes are reviewed. The focus is on the reactor concepts using these membranes and commercial developments that have taken place. In Chapter 3, the feasibility of performing autothermal membrane reforming in a packed bed membrane reactor with perm-selective hydrogen membrane is investigated based on detailed two-dimensional non-isothermal reactor modelling. In Chapter 4, an alternative reactor concept is developed for the autothermal reforming of methane integrating both hydrogen and oxygen perm-selective membranes. In Chapter 5, experimental work on the perm-selective hydrogen membranes that are used in the top section of the proposed reactor concept has been elaborated. These membranes, procured from a commercial supplier, are tested for their perm-selectivity and the permeability of hydrogen at different temperature and hydrogen partial pressures. Using the flux data a lumped flux expression is developed which is subsequently used in the pilot scale reactor design (Chapter 7). In Chapter 6, the kinetic rate measurements for SRM on a highly active Shell CPO catalyst are described. A kinetic rate expression for the steam reforming/ water gas shift top section of the proposed novel reactor concept is developed. The bottom section of this reactor is essentially at thermodynamic equilibrium because of highly active CPO catalyst and high temperatures and hence a detailed kinetic investigation for this section is not undertaken. In Chapter 7, a single membrane prototype of the top section is tested experimentally followed by a scale-up and design to a pilot scale unit with 10 Pd

  17. (Meeting on fusion reactor materials)

    Energy Technology Data Exchange (ETDEWEB)

    Jones, R.H. (Pacific Northwest Lab., Richland, WA (USA)); Klueh, R.L.; Rowcliffe, A.F.; Wiffen, F.W. (Oak Ridge National Lab., TN (USA)); Loomis, B.A. (Argonne National Lab., IL (USA))

    1990-11-01

    During his visit to the KfK, Karlsruhe, F. W. Wiffen attended the IEA 12th Working Group Meeting on Fusion Reactor Materials. Plans were made for a low-activation materials workshop at Culham, UK, for April 1991, a data base workshop in Europe for June 1991, and a molecular dynamics workshop in the United States in 1991. At the 11th IEA Executive Committee on Fusion Materials, discussions centered on the recent FPAC and Colombo panel review in the United States and EC, respectively. The Committee also reviewed recent progress toward a neutron source in the United States (CWDD) and in Japan (ESNIT). A meeting with D. R. Harries (consultant to J. Darvas) yielded a useful overview of the EC technology program for fusion. Of particular interest to the US program is a strong effort on a conventional ferritic/martensitic steel for fist wall/blanket operation beyond NET/ITER.

  18. Reactor operation environmental information document

    Energy Technology Data Exchange (ETDEWEB)

    Wike, L.D.; Specht, W.L.; Mackey, H.E.; Paller, M.H.; Wilde, E.W.; Dicks, A.S.

    1989-12-01

    The Savannah River Site (SRS) is a large United States Department of Energy installation on the upper Atlantic Coastal Plain of South Carolina. The SRS contains diverse habitats, flora, and fauna. Habitats include upland terrestrial areas, varied wetlands including Carolina Bays, the Savannah River swamp system, and impoundment related and riparian wetlands, and the aquatic habitats of several stream systems, two large cooling reservoirs, and the Savannah River. These diverse habitats support a large variety of plants and animals including many commercially or recreational valuable species and several rare, threatened or endangered species. This volume describes the major habitats and their biota found on the SRS, and discuss the impacts of continued operation of the K, L, and P production reactors.

  19. Coacervates as prebiotic chemical reactors

    Science.gov (United States)

    Kolb, Vera M.; Swanson, Mercedes; Menger, Fredric M.

    2012-10-01

    Coacervates are colloidal systems that are comprised of two immiscible aqueous layers, the colloid-rich layer, so-called coacervate, and the colloid-poor layer, so-called equilibrium liquid. Although immiscible, the two phases are both water-rich. Coacervates are important for prebiotic chemistry, but also have various practical applications, notably as transport vehicles of personal care products and pharmaceuticals. Our objectives are to explore the potential of coacervates as prebiotic chemical reactors. Since the reaction medium in coacervates is water, this creates a challenge, since most organic reactants are not water-soluble. To overcome this challenge we are utilizing recent Green Chemistry examples of the organic reactions in water, such as the Passerini reaction. We have investigated this reaction in two coacervate systems, and report here our preliminary results.

  20. Dynamic analysis of process reactors

    Energy Technology Data Exchange (ETDEWEB)

    Shadle, L.J.; Lawson, L.O.; Noel, S.D.

    1995-06-01

    The approach and methodology of conducting a dynamic analysis is presented in this poster session in order to describe how this type of analysis can be used to evaluate the operation and control of process reactors. Dynamic analysis of the PyGas{trademark} gasification process is used to illustrate the utility of this approach. PyGas{trademark} is the gasifier being developed for the Gasification Product Improvement Facility (GPIF) by Jacobs-Siffine Engineering and Riley Stoker. In the first step of the analysis, process models are used to calculate the steady-state conditions and associated sensitivities for the process. For the PyGas{trademark} gasifier, the process models are non-linear mechanistic models of the jetting fluidized-bed pyrolyzer and the fixed-bed gasifier. These process sensitivities are key input, in the form of gain parameters or transfer functions, to the dynamic engineering models.