WorldWideScience

Sample records for pzt

  1. Oriented Growth of PZT thick film embedded with PZT nanoparticles

    Institute of Scientific and Technical Information of China (English)

    DUAN Zhong-xia; YUAN Jie; ZHAO Quan-liang; LU Ran; CAO Mao-sheng

    2009-01-01

    This paper reports that dense and crack-free (100) oriented lead zirconate titanate (Pb(Zr0.52Ti0.48)O3,PZT) thick film embedded with PZT nanoparticles has been successfully fabricated on Pt/Cr/SiO2/Si substrate by using PT transition layer and PVP additive. The thick film possesses single-phase perovskite structure and perfectly (100) oriented. The (100) orientation degree of the PZT films strongly depended on annealing time and for the 4 μm-thick PZT film which was annealed at 700 ℃ for 5 min is the largest. The (100) orientation degree of the PZT thick film gradually strengthen along with the thickness of film decreasing. The 3 μm-thick PZT thick film which was annealed at 700 ℃ for 5 min has the strongest (100) orientation degree, which is 82. 3%.

  2. Temperature Dependent Electrical Properties of PZT Wafer

    Science.gov (United States)

    Basu, T.; Sen, S.; Seal, A.; Sen, A.

    2016-04-01

    The electrical and electromechanical properties of lead zirconate titanate (PZT) wafers were investigated and compared with PZT bulk. PZT wafers were prepared by tape casting technique. The transition temperature of both the PZT forms remained the same. The transition from an asymmetric to a symmetric shape was observed for PZT wafers at higher temperature. The piezoelectric coefficient (d 33) values obtained were 560 pc/N and 234 pc/N, and the electromechanical coupling coefficient (k p) values were 0.68 and 0.49 for bulk and wafer, respectively. The reduction in polarization after fatigue was only ~3% in case of PZT bulk and ~7% for PZT wafer.

  3. Research on Composite PZT for Largedisplacement Actuators

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A new kind of composite piezoelectric ceramics for large-displacement actuators, which were composed of reduced and unreduced layers, was prepared from normal PZT by chemical reduction. The stress distribution inside the composite PZT was researched and the chemical reduction conditions were explored.The actuating properties of reduced PZT were also studied. It is found that the optimal ratio of reduced layer thickness for the composite structure is 0.3; Reduced composite PZT has lower resonance frequency and 3 times larger displacement than that of the traditional PZT; Re-oxide phases are found in reduced layer of composite PZT showing the reduction procedure needs to be improved.

  4. Performance of PZT8 Versus PZT4 Piezoceramic Materials in Ultrasonic Transducers

    Science.gov (United States)

    DeAngelis, Dominick A.; Schulze, Gary W.

    PZT8 and PZT4 are the common "hard" piezoceramic materials used in power ultrasonic transducers (e.g., welding, cutting, sonar, etc.). PZT8 is perceived as the better choice for resonant devices, primarily due to its higher mechanical quality factor Qm. PZT8 is also considered a "harder" material compared to PZT4, since it has better stability at higher preloads and drive levels. Many transducer designers never consider PZT4 for their applications, even though it has clear advantages such as higher output (i.e., higher d33). Even the perceived advantage of PZT8 regarding Qm may not be significant for most Langevin, bolted stack type transducers if the mechanical joint losses dominate. This research is a case study on the performance of identical ultrasonic transducers used for semiconductor wire bonding, assembled with either PZT8 or PZT4 materials. The main purpose of the study is to establish rule-of-thumb transducer design guidelines for the selection of PZT8 versus PZT4 materials. Several metrics are investigated such as impedance, frequency, capacitance, dielectric loss, Qm, heating, displacement gain, and electro-mechanical coupling factor. The experimental and theoretical research methods include Bode plots, thermal IR camera imaging, scanning laser vibrometry and coupled-field finite element analysis.

  5. Microwave Hydrothermal Synthesis PZT of Nanometer Crystal

    Institute of Scientific and Technical Information of China (English)

    Hongxing LIU; Hong DENG; Yan LI; Yanrong LI

    2004-01-01

    It was focused on the applications and developments of microwave hydrothermal synthesis piezoelectric ceramic powder. The microwave hydrothermal vessel was designed and manufactured. The microwave hydrothermal synthesis system was established and the PZT piezoelectric ceramic powder was synthesized. XRD and TEM have been used to characterize the products in detail. The diameter of the PZT powder particle is from 40 to 60 nm.

  6. Polarization characterization of PZT disks and of embedded PZT plates by thermal wave methods

    Energy Technology Data Exchange (ETDEWEB)

    Eydam, Agnes, E-mail: Agnes.Eydam@tu-dresden.de; Suchaneck, Gunnar, E-mail: Agnes.Eydam@tu-dresden.de; Gerlach, Gerald [Technische Universität Dresden, Solid State Electronics Laboratory, Helmholtzstraße 18, 01062 Dresden (Germany); Esslinger, Sophia; Schönecker, Andreas; Neumeister, Peter [Fraunhofer Institute for Ceramic Technologies and Systems, Winterbergstraße 28, 01277 Dresden (Germany)

    2014-11-05

    In this work, the thermal wave method was applied to characterize PZT disks and embedded PZT plates with regard to the polarization magnitude and spatial homogeneity. The samples were exposed to periodic heating by means of a laser beam and the pyroelectric response was determined. Thermal relaxation times (single time constants or distributions of time constants) describe the heat losses of the PZT samples to the environment. The resulting pyroelectric current spectrum was fitted to the superposition of thermal relaxation processes. The pyroelectric coefficient gives insight in the polarization distribution. For PZT disks, the polarization distribution in the surface region showed a characteristic decrease towards the electrodes.

  7. Screen printed PZT/PZT thick film bimorph MEMS cantilever device for vibration energy harvesting

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Dahl-Petersen, Christian

    2012-01-01

    We present a microelectromechanical system (MEMS) based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass. Most piezoelectric energy harvesting devices use a cantilever beam of a non piezoelectric material as support beneath or in-between the piezoelectri...

  8. Mems-based pzt/pzt bimorph thick film vibration energy harvester

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Dahl-Petersen, Christian

    2011-01-01

    We describe fabrication and characterization of a significantly improved version of a MEMS-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass. The main advantage of bimorph vibration energy harvesters is that strain energy is not lost in mechanical...... support materials since only PZT is strained, and thus it has a potential for significantly higher output power. An improved process scheme for the energy harvester resulted in a robust fabrication process with a record high fabrication yield of 98.6%. Moreover, the robust fabrication process allowed...... a high pressure treatment of the screen printed PZT thick films prior to sintering, improving the PZT thick film performance and harvester power output reaches 37.1 μW at 1 g....

  9. Smart Energy Materials of PZT Ceramics

    Directory of Open Access Journals (Sweden)

    Mitsuhiro Okayasu

    2017-03-01

    Full Text Available To better understand the material properties of lead zirconate titanate (PZT ceramics, the domain-switching characteristics and electric power generation characteristics have been investigated during loading and unloading by using various experimental techniques. Furthermore, the influence of oscillation condition on the electrical power generation properties of lead zirconate titanate (PZT piezoelectric ceramics has been investigated. It is found that the power generation is directly attributed to the applied load and wave mode. The voltage rises instantly to the maximum level under square-wave mode, although the voltage increases gradually under triangular-wave mode. After this initial increase, there is a rapid fall to zero, followed by generation of increasingly negative voltage as the applied load is removed for all wave modes. Variation of the electric voltage is reflected by the cyclic loading at higher loading frequencies. On the basis of the obtained experimental results for the wave modes, the electrical power generation characteristics of PZT ceramics are proposed, and the voltages generated during loading and unloading are accurately estimated. The electric generation value is decrease with increasing the cyclic number due to the material failure, e.g., domain switching and crack. The influence of domain switching on the mechanical properties PZT piezoelectric ceramics is clarified, and 90 degree domain switching occurs after the load is applied to the PZT ceramic directly. Note that, in this paper, our experimental results obtained in our previous works were introduced

  10. Design and fabrication of aspherical bimorph PZT optics

    CERN Document Server

    Tseng, T C; Yeh, Z C; Perng, S Y; Wang, D J; Kuan, C K; Chen, J R; Chen, C T

    2001-01-01

    Bimorph piezoelectric optics with a third-order-polynomial surface is designed and a prototype is fabricated as active optics. Two pairs of silicon (Si) and lead zirconate titanate (PZT) piezoelectric ceramic are bonded as Si-PZT-PZT-Si together with a multi-electrode or thin film resistor coating used as the control electrode between Si and PZT and metallic films as grounding between the interface of PZT ceramics. A linear voltage is applied to the bimorph PZT optics by probing the control electrodes from a two-channel controllable power supplier. In doing so, the optics surface can achieve a desired third-order-polynomial surface. Reducing hysteresis and creep in bimorph PZT X-ray optics is the only feasible way by inserting an appropriate capacitor in series with bimorph PZT optics to significantly reduce both effects.

  11. Pyroelectric Charge Release in Rhombohedral PZT

    NARCIS (Netherlands)

    Noheda, Beatriz; Duan, Ning; Cereceda, Noé; Gonzalo, Julio A.

    1998-01-01

    A new experimental set-up controlled by computer has been made to measure the pyroelectric charge of ferroelectric materials with a relatively high conductivity at slow rates of temperature variation. It allowed us to obtain the polarisation vs. temperature behaviour of PZT with various compositions

  12. Flexible graphene-PZT ferroelectric nonvolatile memory

    Science.gov (United States)

    Lee, Wonho; Kahya, Orhan; Tat Toh, Chee; Özyilmaz, Barbaros; Ahn, Jong-Hyun

    2013-11-01

    We report the fabrication of a flexible graphene-based nonvolatile memory device using Pb(Zr0.35,Ti0.65)O3 (PZT) as the ferroelectric material. The graphene and PZT ferroelectric layers were deposited using chemical vapor deposition and sol-gel methods, respectively. Such PZT films show a high remnant polarization (Pr) of 30 μC cm-2 and a coercive voltage (Vc) of 3.5 V under a voltage loop over ±11 V. The graphene-PZT ferroelectric nonvolatile memory on a plastic substrate displayed an on/off current ratio of 6.7, a memory window of 6 V and reliable operation. In addition, the device showed one order of magnitude lower operation voltage range than organic-based ferroelectric nonvolatile memory after removing the anti-ferroelectric behavior incorporating an electrolyte solution. The devices showed robust operation in bent states of bending radii up to 9 mm and in cycling tests of 200 times. The devices exhibited remarkable mechanical properties and were readily integrated with plastic substrates for the production of flexible circuits.

  13. Lamb wave dispersion in a PZT/metal/PZT sandwich plate with imperfect interface

    Science.gov (United States)

    Kurt, Ilkay; Akbarov, Surkay D.; Sezer, Semih

    2016-07-01

    The Lamb wave dispersion in a PZT/Metal/PZT sandwich plate is investigated by employing the exact linear equations of electro-elastic waves in piezoelectric materials within the scope of the plane-strain state. It is assumed that at the interfaces between the piezoelectric face layers and metal core layer, shear-spring and normal-spring type imperfect conditions are satisfied. The degree of this imperfectness is estimated through the corresponding shear-spring and normal-spring type parameters which appear in the contact condition characterizing the transverse and normal displacements' discontinuity. The corresponding dispersion equation is derived, and as a result of the numerical solution to this equation, the dispersion curves are constructed for the first and second lowest modes in the cases where the material of the face layers is PZT and the material of the middle layer is Steel (St). Consequently, for the PZT/St/PZT sandwich plate, the study of the influence of the problem parameters such as the piezoelectric and dielectric constants, layer thickness ratios, non-dimensional shear-spring, and normal-spring type parameters, is carried out. In particular, it is established that the imperfectness of the contact between the layers of the plate causes a decrease in the values of the wave propagation velocity.

  14. Magnetoelectric effect in metal–PZT laminates

    Indian Academy of Sciences (India)

    S Narendra Babu; T Bhimasankaram; S V Suryanarayana

    2005-08-01

    Magnetoelectric (ME) composites are two-phase composites consisting of piezoelectric and piezomagnetic materials as the participating constituents. These magnetoelectric composites when placed under external magnetic field, show electrical polarization (magnetoelectric output). The ME coupling is mediated by mechanical stress. In the present study, we have synthesized Ni/PZT/Ni and Fe/PZT/Fe layered composites for studying their ME output by dynamic magnetoelectric set up in which both d.c. and a.c. magnetic fields can be varied. The ME output obtained in these composites are higher than those obtained in 40% Ni0.97Co0.03Mn0.01 Fe1.9O4 + 60% BaTi1.02O3.04. The results with varying d.c. and a.c. magnetic fields are presented.

  15. Fabrication, characterization and applications of PZT and ITO nanostructures

    Science.gov (United States)

    Xu, Shiyou

    Lead Zirconate Titanate (PbZr1--xTixO 3, PZT) is one of the most important piezoelectric materials, which has been used traditionally as sensors and actuators. One dimensional (1-D) PZT is expected to have great potentials as building blocks for micro and nano sensors and actuators, nano active fiber composites and integrated nanosystems. The objective of this research is to investigate the size effect on mechanical and piezoelectric properties through the fabrication and characterization of 1-D PZT nanostructures such as PZT nanofibers and nanotubes. The electrospinning process and template-assisted method were used to synthesize PZT nanofibers and nanotubes, respectively. Various novel experimental methods, such as atomic force microscopy (AFM) and nanomanipulator, were used to characterize the mechanical and piezoelectric properties of PZT nanostructures. The obtained results have shown that the piezoelectric and mechanical properties of PZT are size dependent. A single PZT nanofiber presented a lower young's modulus (42.99 GPa measured from AFM-base method and 46.6 GPa from vibration-based method, respectively) than that of PZT thin films and bulks. The PZT nanofibers with diameters smaller than 150 nm still demonstrated a strong electromechanical coupling effect. The piezoelectric constant (d 33) of PZT nanofibers increased from 574.1 pm/V to 860.5 pm/V when their diameters decreased from 112 nm to 50 nm. PZT nanotubes were found to have a d33 value of up to 595 pm/V. These values are significantly higher than that of PZT thin films and comparable to that of PZT bulks. The PZT nanofibers and nanotubes developed in this research not only provide new types of sensing and actuation mechanisms for various novel nanodevices, but also provide significantly improved performance compared with their thin film counterpart used in microelectromechanical systems (MEMS). 1-D ITO nanostructures (nanofibers and nanotubes) were synthesized and characterized for potential use

  16. Active PZT fibers: a commercial production process

    Science.gov (United States)

    Strock, Harold B.; Pascucci, Marina R.; Parish, Mark V.; Bent, Aaron A.; Shrout, Thomas R.

    1999-07-01

    Lead Zirconate Titanate (PZT) active fibers, from 80 to 250 micrometers in diameter, are produced for the AFOSR/DARPA funded Active Fiber Composites Consortium (AFCC) Program and commercial customers. CeraNova has developed a proprietary ceramics-based technology to produce PZT mono-filaments of the required purity, composition, straightness, and piezoelectric properties for use in active fiber composite structures. CeraNova's process begins with the extrusion of continuous lengths of mono-filament precursor fiber from a plasticized mix of PZT-5A powder. The care that must be taken to avoid mix contamination is described using illustrations form problems experiences with extruder wear and metallic contamination. Corrective actions are described and example microstructures are shown. The consequences of inadequate lead control are also shown. Sintered mono- filament mechanical strength and piezoelectric properties data approach bulk values but the validity of such a benchmark is questioned based on variable correlation with composite performance measures. Comb-like ceramic preform structures are shown that are being developed to minimize process and handling costs while maintaining the required mono-filament straightness necessary for composite fabrication. Lastly, actuation performance data are presented for composite structures fabricated and tested by Continuum Control Corporation. Free strain actuation in excess of 2000 microstrain are observed.

  17. Fabrication and characterization of MEMS-based PZT/PZT bimorph thick film vibration energy harvesters

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Dahl-Petersen, Christian

    2012-01-01

    We describe the fabrication and characterization of a significantly improved version of a microelectromechanical system-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass; the harvester is fabricated in a fully monolithic process. The main advantage...... of bimorph vibration energy harvesters is that strain energy is not lost in mechanical support materials since only Pb(ZrxTi1-x)O3 (PZT) is strained; as a result, the effective system coupling coefficient is increased, and thus a potential for significantly higher output power is released. In addition, when...... the two layers are connected in series, the output voltage is increased, and as a result the relative power loss in the necessary rectifying circuit is reduced. We describe an improved process scheme for the energy harvester, which resulted in a robust fabrication process with a record high fabrication...

  18. Adjustability of resonance frequency by external magnetic field and bias electric field of sandwich magnetoelectric PZT/NFO/PZT composites

    Science.gov (United States)

    Xu, Ling-Fang; Feng, Xing; Sun, Kang; Liang, Ze-Yu; Xu, Qian; Liang, Jia-Yu; Yang, Chang-Ping

    2017-07-01

    Sandwich magnetoelectric composites of PZT/NFO/PZT (PNP) have been prepared by laminating PZT5, NiFe2O4, and PZT5 ceramics in turn with polyvinyl alcohol (PVA) paste. A systematic study of structural, magnetic and ferroelectric properties is undertaken. Structural studies carried out by X-ray diffraction indicate formation of cubic perovskite phase of PZT5 ceramic and cubic spinel phase of NiFe2O4 ceramic. As increasing the content of PZT5 phase, ferroelectric loops and magnetic loops of PNP composites showed increasing remnant electric polarizations and decreasing remnant magnetic moments separately. Both external magnetic fields and bias voltages could regulate the basal radial resonance frequency of the composites, which should be originated with the transformation and coupling of the stress between the piezoelectric phase and magnetostrictive phase. Such magnetoelectric composite provides great opportunities for electrostatically tunable devices.

  19. Screen printed PZT/PZT thick film bimorph MEMS cantilever device for vibration energy harvesting

    DEFF Research Database (Denmark)

    Xu, Ruichao; Lei, Anders; Christiansen, T.L.

    2011-01-01

    We present a MEMS-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass. The most common piezoelectric energy harvesting devices utilize a cantilever beam of a non piezoelectric material as support beneath or in-between the piezoelectric material....... It provides mechanical support but it also reduces the power output. Our device replaces the support with another layer of the piezoelectric material, and with the absence of an inactive mechanical support all of the stresses induced by the vibrations will be harvested by the active piezoelectric elements....

  20. Piezoelectric and mechanical properties of structured PZT-epoxy composites

    NARCIS (Netherlands)

    James, N.K.; Ende, D.A. van den; Lafont, U.; Zwaag, S. van der; Groen, W.A.

    2013-01-01

    Structured lead zirconium titanate (PZT)-epoxy composites are prepared by dielectrophoresis. The piezoelectric and dielectric properties of the composites as a function of PZT volume fraction are investigated and compared with the corresponding unstructured composites. The effect of poling voltage o

  1. Ceramics like PZT-PMN; Ceramicas do tipo PZT-PMN

    Energy Technology Data Exchange (ETDEWEB)

    Droescher, R.E.; Sousa, V.C. [Universidade Federal do Rio Grande do Sul (LABIOMAT/DEMAT/UFRGS), Porto Alegre, RS (Brazil). Dept. de Materiais. Lab. de Biomateriais; Bergman, C.P. [Universidade Federal do Rio Grande do Sul (LACER/DEMAT/UFRGS), Porto Alegre, RS (Brazil). Dept. de Materiais. Lab. de Ceramicas Avancadas

    2009-07-01

    The goal of this work was to achieve piezoelectric ceramics referring to the system PZT-PMN Pb(Mg{sub 1}/{sub 3}Nb{sub 2}/{sub 3}Zr{sub 0},{sub 52}Ti{sub 0},{sub 48})O{sub 3} . Have been analysed ceramics like 0,65PZT-0,35PMN ((Pb(Mg{sub 0},{sub 1167}Nb{sub 0},{sub 2300}Zr{sub 0},{sub 3380}Ti{sub 0},{sub 3120})O{sub 3}), 0,75PZT-0,25PMN ((Pb(Mg{sub 0},{sub 083}Nb{sub 0}.{sub 1675}Zr{sub 0},{sub 3900}Ti{sub 0},{sub 3600})O3) and the 0,85PZT-0,15PMN ((Pb(Mg{sub 0,0500}Nb{sub 0},{sub 1000}Zr{sub 0},{sub 4420}Ti{sub 0},{sub 4080})O{sub 3}). The influence of the calcination and concentration of PZT on the lattice phases, microstructure and density was evaluated. Then, the method used was the mixed-oxide method, the samples were taken under different temperatures of calcination before the final sinterizing. The DRX and SEM techniques were used to identify the phases formed and analyse the microstructure, respectively. The main result revealed that, the better way is to realize three burns before the final sinterizing at 1200 o C/4 h . Like that, on obtain for sure the average lattice phases, like: perovskite, pyrochlore and PbO and also tend to densify the samples. (author)

  2. Electrical Impedance Measurements of PZT Nanofiber Sensors

    Directory of Open Access Journals (Sweden)

    Richard Galos

    2017-01-01

    Full Text Available Electrical impedance measurements of PZT nanofiber sensors were performed using a variety of methods over a frequency spectrum ranging from DC to 1.8 GHz. The nanofibers formed by electrospinning with diameters ranging from 10 to 150 nm were collected and integrated into sensors using microfabrication techniques. Special matching circuits with ultrahigh input impedance were fabricated to produce low noise, measurable sensor outputs. Material properties including resistivity and dielectric constant are derived from the impedance measurements. The resulting material properties are also compared with those of individual nanofibers being tested using conductive AFM and Scanning Conductive Microscopy.

  3. Energy harvesting from vertically aligned PZT nanowire arrays

    Science.gov (United States)

    Malakooti, Mohammad H.; Zhou, Zhi; Sodano, Henry A.

    2016-04-01

    In this paper, a nanostructured piezoelectric beam is fabricated using vertically aligned lead zirconate titanate (PZT) nanowire arrays and its capability of continuous power generation is demonstrated through direct vibration tests. The lead zirconate titanate nanowires are grown on a PZT thin film coated titanium foil using a hydrothermal reaction. The PZT thin film serves as a nucleation site while the titanium foil is used as the bottom electrode. Electromechanical frequency response function (FRF) analysis is performed to evaluate the power harvesting efficiency of the fabricated device. Furthermore, the feasibility of the continuous power generation using the nanostructured beam is demonstrated through measuring output voltage from PZT nanowires when beam is subjected to a sinusoidal base excitation. The effect of tip mass on the voltage generation of the PZT nanowire arrays is evaluated experimentally. The final results show the great potential of synthesized piezoelectric nanowire arrays in a wide range of applications, specifically power generation at nanoscale.

  4. Preparation and Characterization of PZT Wafers

    Science.gov (United States)

    Seal, A.; Rao, B. S. S. Chandra; Kamath, S. V.; Sen, A.; Maiti, H. S.

    2008-07-01

    Piezoelectric materials have recently attracted a lot of attention for ultrasonic structural health monitoring (shm) in aerospace, defence and civilian sectors, where they can act as both actuators and sensors. Incidentally, piezoelectric materials in the form of wafers (pwas-piezoelectric wafer active sensor, approx. 5-10 mm square and 0.2-0.3 mm thickness) are inexpensive, non intrusive and non-resonant wide band devices that can be surface-mounted on existing structures, inserted between the layers of lap joints or embedded inside composite materials. The material of choice for piezoelectric wafers is lead zirconate titanate (PZT) of composition close to morphotropic phase boundary [pb(zr0.52 ti0.48)o3]. However, an excess pbo is normally added to pzt as a densification aid and also to make up for the lead loss during high temperature sintering. Hence, it is of paramount importance to know how the shift of the lead content from the morphotropic composition affects the piezoelectric and mechanical properties of the sintered wafers, keeping in view the importance of mechanical properties of wafers in shm. In the present study, we observed that with the increase in the lead content of the sintered wafers, the dielectric and piezoelectric constants decreased. However, the elastic modulus, hardness and fracture toughness of the wafers increased with increasing lead content in the composition. Hence, the lead content in the sintered wafers should be optimized to get acceptable piezoelectric and mechanical

  5. Directed colloidal assembly and characterization of PZT-polymer composites

    Science.gov (United States)

    Smay, James Earl

    Lead zirconate titanate (PZT)-based layers and 3-D structures were directly assembled using two colloidal routes: (1) tape casting and (2) a layer-by-layer robotic deposition technique, known as robocasting. First, concentrated (φsolids > 0.45) suspensions of PZT-5H and a latex emulsion were tape cast with the aid of viscosifier and surfactant additions. Drying stress evolved to a maximum at φ PZT ˜ 0.49, followed by a reduction and a secondary stress rise attributed to latex coalescence. Dielectric and piezoelectric properties of sintered PZT multilayer laminates exhibited good agreement with those for isostatically pressed and sintered samples. Concentrated, weakly gelled suspensions of PZT 95/5 and poly(ethylene) (PE) latices, a fugitive species, were developed as inks for the robotic deposition of monolithic and tri-layered composite structures. Monoliths, with densities of 93.6% and 96.1%, and composites with a 96.1% dense layer between 93.6% regions were fabricated. The structures displayed equivalent electrical properties to cold isostatically pressed parts. The composites withstood repeated saturation polarization switching as well as a 500 MPa hydrostatic pressure-induced poled ferroelectric (FE) to antiferroelectric (AFE) phase transformation. Concentrated (φPZT = 0.47) PZT-5H gels were developed as inks for the robotic deposition of 3-D, mesoscale periodic structures with self-supporting features such as lattices of rod-like elements and v-shaped test structures. The gels exhibited pH dependent viscoelastic properties and Hershel-Bulkley flow behavior. The deflection of as-deposited spanning elements was measured using laser profilometry. Flow modeling and shape evolution data indicated a core-shell architecture as the ink exited the deposition nozzle, which simultaneously provided strength to form spanning elements and good bonding between layers. The core grew rapidly (˜1s) due to the quick recovery of gel structure in these inks. 3-X type PZT

  6. Characterization of PZT thin films on metal substrates; Charakterisierung von PZT-Duennschichten auf Metallsubstraten

    Energy Technology Data Exchange (ETDEWEB)

    Dutschke, A.

    2008-02-02

    Lead zirconate titanate (PbZr{sub x}Ti{sub 1-x}O{sub 3},PZT) is one of the most applied ceramic materials because of its distinctive piezo- and ferroelectric properties. Prepared as thin films on flexible, metallic substrates it can be used for various applications as strain gauges, key switches, vibration dampers, microactuators and ultrasonic transducers. The aim of this work is to analyze the microstructure and the phase-content of PZT-thin films deposited on temperature- und acid-resistant hastelloy-sheets, to correlate the results with the ferroelectric and dielectric properties. It is demonstrated, that the specific variation of the microstructure can be achieved by different thermal treatments and the selective addition of Neodymium as dopant. Nd-doping leads to a shift of the maximum nucleation rate towards reduced temperatures and a decrease in the rate of growth compared to undoped films. The PZT-films are prepared by a sol-gel-process in fourfold multilayers with a composition near the morphotropic phase boundary, where the tetragonal und rhombohedral perovskite-phases coexist. The crystallisation in Nd-doped and undoped films takes place heterogeneously, preferentially at the interfaces and on the surface of the multilayered films as well as on the inner surface of pores within the films. For the first time, the Zr:Ti fluctuation phenomena emerging in sol-gel derived PZT films is related to the microstructure and the local phase content on a nanometer scale. In this connection it is proved, that long-distance Zr:Ti gradients arise preferentially before and during the crystallisation of the pyrochlore phase. During the following crystallisation of the perovskite phase, the crystallites grow across these gradients without modifying them. It is pointed out that the fluctuation in the Zr:Ti ratio has only minor influence on the amount of the tetragonal or rhombohedral distortion of the crystallites after the transition from the para- to the ferroelectric

  7. Study of pyroelectric activity of PZT/PVDF-HFP composite

    Directory of Open Access Journals (Sweden)

    Luiz Francisco Malmonge

    2003-12-01

    Full Text Available Flexible, free-standing piezo and pyroelectric composite with 0 to 3 connectivity was made up from Lead Zirconate Titanate (PZT powder and poly(vinylidene fluoride-hexafluoropropylene (PVDF-HFP copolymer. The pyroelectric and the piezoelectric longitudinal (d33 coefficients were measured. A 50/50 vol.% PZT/PVDF-HFP composite resulted in piezo and pyroelectric coefficients of d33 = 25.0 pC/N and p = 4.5 × 10-4 C/m²K at 70 °C, respectively. Analysis of the complex permittivity in a wide range of frequency was carried out indicating lower permittivity of the composite in comparison with a permittivity of the PZT ceramic. The low value of the permittivity gives a high pyroelectric figure of merit indicating that this material can be used to build a temperature sensor in spite of the lower pyroelectric coefficient compared with PZT.

  8. Advantages of PZT thick film for MEMS sensors

    DEFF Research Database (Denmark)

    Hindrichsen, Christian Carstensen; Lou-Moller, R.; Hansen, K.;

    2010-01-01

    For all MEMS devices a high coupling between the mechanical and electrical domain is desired. Figures of merit describing the coupling are important for comparing different piezoelectric materials. The existing figures of merit are discussed and a new figure of merit is introduced for a fair...... comparison of piezoelectric thin and thick films based MEMS devices, as cantilevers, beams, bridges and membranes. Simple analytical modeling is used to define the new figure of merit. The relevant figure of merits is compared for the piezoelectric material of interest for MEMS applications: ZnO, AIN, PZT...... thin film and PZT thick film. It is shown that MEMS sensors with the PZT thick film TF2100 from InSensor A/S have potential for significant higher voltage sensitivities compared to PZT thin film base MEMS sensors when the total thickness of the MEMS cantilever, beam, bridge or membrane is high...

  9. Compatibility of RuO2 electrodes with PZT ceramics

    Indian Academy of Sciences (India)

    K T Jacob; G Rajitha; V S Saji

    2009-06-01

    Because of its high electrical conductivity and good diffusion barrier properties ruthenium dioxide (RuO2) is a good electrode material for use with ferroelectric lead zirconate–titanate (PZT) solid solutions. Under certain conditions, RuO2 can react with PZT to form lead ruthenate (Pb2Ru2O6.5) during processing at elevated temperatures resulting in lead depletion from PZT. The standard Gibbs energies of formation of RuO2 and Pb2Ru2O6.5 and activities of components of the PZT solid solution have been determined recently. Using this data along with older thermodynamic information on PbZrO3 and PbTiO3, the stability domain of Pb2Ru2O6.5 is computed as a function of PZT composition, temperature and oxygen partial pressure in the gas phase. The results show PbZrO3-rich compositions are more prone to react with RuO2 at all temperatures. Increasing temperature and decreasing oxygen partial pressure suppress the reaction. Graphically displayed are the reaction zones as a function of oxygen partial pressure and PZT composition at temperatures 973, 1173 and 1373 K.

  10. Standing wave brass-PZT square tubular ultrasonic motor.

    Science.gov (United States)

    Park, Soonho; He, Siyuan

    2012-09-01

    This paper reports a standing wave brass-PZT tubular ultrasonic motor. The motor is composed of a brass square tube with two teeth on each tube end. Four PZT plates are attached to the outside walls of the brass tube. The motor requires only one driving signal to excite vibration in a single bending mode to generate reciprocating diagonal trajectories of teeth on the brass tube ends, which drive the motor to rotate. Bi-directional rotation is achieved by exciting different pairs of PZT plates to switch the bending vibration direction. Through using the brass-PZT tube structure, the motor can take high magnitude vibration to achieve a high output power in comparison to PZT tube based ultrasonic motors. Prototypes are fabricated and tested. The dimension of the brass-PZT tube is 3.975mm×3.975mm×16mm. Measured performance is a no-load speed of >1000RPM, a stall torque of 370μNm and a maximum output power of 16 mW when a sinusoidal driving voltage of 50V is applied. The working frequencies of the motor are 46,050Hz (clockwise) and 46,200Hz (counter-clockwise).

  11. Instantaneous crack detection using dual PZT transducers

    Science.gov (United States)

    Kim, Seung Bum; Sohn, Hoon

    2008-03-01

    A new guided wave based nondestructive testing (NDT) technique is developed to detect crack damage in metallic plates commonly used in aircraft without using prior baseline data or a predetermined decision boundary. In conventional guided wave based techniques, damage is often identified by comparing the "current" data obtained from a potentially damaged condition of a structure with the "past" baseline data collected at the pristine condition of the structure. However, it has been reported that this type of pattern comparison with the baseline data can lead to increased false alarms due to its susceptibility to varying operational and environmental conditions of the structure. In order to tackle this issue, a reference-free damage detection technique is previously developed using two pairs of collocated lead zirconate titanate transducers (PZTs) placed on both sides of a plate. In this study, this reference-free technique is further advanced so that the PZT transducers can be placed only on one side of the specimen. Crack formation creates Lamb wave mode conversion due to a sudden change in the thickness of the structure. Then, the proposed technique instantly detects the appearance of the crack by extracting this mode conversion from the measured Lamb waves. This study suggests a reference-free statistical approach that enables damage classification using only the current data set. Numerical and experimental results are presented to demonstrate the applicability of the proposed technique to instantaneous crack detection.

  12. Comparison of the thermal degradation of heavily Nb-doped and normal PZT thin films.

    Science.gov (United States)

    Yang, Jeong-Suong; Kang, Yunsung; Kang, Inyoung; Lim, Seungmo; Shin, Seung-Joo; Lee, Jungwon; Hur, Kangheon

    2017-01-04

    The degradation of Niobium-doped lead zirconate titanate (PZT) and two types of PZT thin films were investigated. Undoped PZT, 2-step PZT and heavily Nb-doped PZT (PNZT) around the morphotropic phase boundary (MPB) were in-situ deposited under optimum condition by RF-magnetron sputtering. All 2 μm thick films had dense perovskite columnar grain structure and self-polarized (100) dominant orientation. PZT thin films were deposited on Pt/TiOx bottom electrode on Si wafer, and Nb doped PZT thin film was on Ir/TiW electrode with help of orientation control. Sputtered PZT films formed on MEMS gyroscope, and the degradation rates were compared at different temperatures. Nb-doped PZT showed the best resistance to the thermal degradation, followed by 2-step PZT. To clarify the effect of oxygen vacancies for the degradation of the film at high temperature, photo-luminescence (PL) measurement was conducted. It confirmed that oxygen vacancy rate was the lowest in heavily Nb-doped PZT. Nb-doping PZT thin films suppressed the oxygen deficit and made high imprint with self-polarization. This defect distribution and high internal field allowed Nb-doped PZT thin film to make the piezoelectric sensors more stable and reliable at high temperature, such as reflow process of micro-electromechanical system (MEMS) packaging.

  13. Scaling laws In PZT/Si(001) Thin Films

    Science.gov (United States)

    Ramírez, Juan; Cortes, Alexander; Lopera, Wilson; Gómez, Maria Elena; Prieto, Pedro

    2006-03-01

    Self-affine scaling behavior of ferroelectric Pb(Zr1-xTix)O3 (PZT) thin films grown on Si(001) substrates has been investigated by AFM Atomic Force Microscope. PZT thin films were grown via Rf-sputtering technique at high oxygen pressures and at substrate temperatures 600 ^oC varying the deposition time and keeping all parameters. growth constant. The α-global rough-exponent was founded close to 0.7 indicating a correlated growth. Anomalous scaling behavior was founded in all PZT/Si surfaces. A value of 0.5.for the α-local value was founded. The local value of the roughness exponent is associated to the diffusional process on the first stage growth. Saturation roughness showed oscillation dependence with the PZT-thickness. This dependence can be explained by the mismatch between Si substrate and PZT thin film. These results are corroborated calculating the grain size for all samples. This work was supported by COLCIENCIAS under the Excellence Center for Novel Materials Contract no 0043-2005.

  14. Flexible PZT Thin Film Tactile Sensor for Biomedical Monitoring

    Directory of Open Access Journals (Sweden)

    Wen-Jong Wu

    2013-04-01

    Full Text Available This paper presents the development of tactile sensors using the sol-gel process to deposit a PZT thin-film from 250 nm to 1 μm on a flexible stainless steel substrate. The PZT thin-film tactile sensor can be used to measure human pulses from several areas, including carotid, brachial, finger, ankle, radial artery, and the apical region. Flexible PZT tactile sensors can overcome the diverse topology of various human regions and sense the corresponding signals from human bodies. The measured arterial pulse waveform can be used to diagnose hypertension and cardiac failure in patients. The proposed sensors have several advantages, such as flexibility, reliability, high strain, low cost, simple fabrication, and low temperature processing. The PZT thin-film deposition process includes a pyrolysis process at 150 °C/500 °C for 10/5 min, followed by an annealing process at 650 °C for 10 min. Finally, the consistent pulse wave velocity (PWV was demonstrated based on human pulse measurements from apical to radial, brachial to radial, and radial to ankle. It is characterized that the sensitivity of our PZT-based tactile sensor was approximately 0.798 mV/g.

  15. Synthesis of piezoelectric nanocrystalline PZT powder by stearic acid gel method

    Institute of Scientific and Technical Information of China (English)

    HAO Junjie; WANG Xiaohui; GUI Zhilun; LI Longtu

    2005-01-01

    PZT nanocrystalline powder was prepared by a stearic acid gel method. The crystallization process from the precursor was monitored by infrared spectroscopy, differential thermal analysis, and thermogravimetric analysis. The nano-sized PZT powder was characterized by X-ray diffraction and transmission electron microscopy. It shows that pure single-phase PZT powder could be obtained at 450℃ for 1 h, and the particle size is about 20 nm. With an increase in the calcination temperature, the PZT crystallite size increased.

  16. Sol-gel PZT and Mn-doped PZT thin films for pyroelectric applications

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Q. [Advanced Materials Group, School of Industrial and Manufactory Science, Cranfield University, Beds (United Kingdom)]. E-mail: q.zhang@cranfield.ac.uk; Whatmore, R.W. [Advanced Materials Group, School of Industrial and Manufactory Science, Cranfield University, Beds (United Kingdom)

    2001-08-07

    Thin films of ferroelectric lead zirconate titanate (PbZr{sub 0.3}Ti{sub 0.7}O{sub 3} PZT30/70) and manganese-doped lead zirconate titanate ((Pb(Zr{sub 0.3}Ti{sub 0.7}){sub 1-x}Mn{sub x})O{sub 3}, where x=0.01, PM01ZT30/70; and x=0.03, PM03ZT30/70) have been prepared using sol-gel processing techniques. These materials can be used as the pyroelectric thin films in uncooled infrared detectors. The thin films were prepared via a sol-gel route based on a hybrid solvent of methanol and ethanol with acetic acid, ethanolamine and ethylene glycol as additives. The final solution is non-moisture sensitive and stable. Films deposited on Pt/Ti/SiO{sub 2}/Si substrates and annealed on a hot plate at 500-530{sup 0}C for a few minutes were seen to fully crystallize into the required perovskite phase and showed excellent ferroelectric behaviour, demonstrated by reproducible hysteresis loops (P{sub r}=33-37 {mu}C cm{sup -2}, Ec(+)=70-100 kV cm{sup -1}, Ec(-)=-170 to -140 kV cm{sup -1}). The pyroelectric coefficient (p) was measured using the Byer-Roundy method. At 20 deg. C, p was 2.11x10{sup -4} C m{sup -2} K{sup -1} for PZT30/70, 3.00x10{sup -4} C m{sup -2} K{sup -1} for PM01ZT30/70 and 2.40x10{sup -4} C m{sup -2} K{sup -1} for PM03ZT30/70 thin films. The detectivity figure-of-merit (F{sub D}) was 1.07x10{sup -5} Pa{sup -0.5} for PZT30/70, 3.07x10{sup -5} Pa{sup -0.5} for PM01ZT30/70 and 1.07x10{sup -5} Pa{sup -0.5} for PM03ZT30/70. These figures compare well with values reported previously. (author)

  17. Modeling of PZT Ferroelectric Ceramic Depolarization Driven by Shock Stress

    Institute of Scientific and Technical Information of China (English)

    LAN Chao-Hui; PENG Yu-Fei; LONG Ji-Dong; WANG Qiang; WANG Wen-Dou

    2011-01-01

    @@ Shock-induced phase transition of ferroelectric ceramic PZT 95/5 causes elastic stiffening and depolarization,releasing stored electrostatic energy into the load circuit.We develop a model to describe the response of the PZT ferroelectric ceramic and implement it into simulation codes.The model is based on the phenomenological theory of phase transition dyynamics and takes into account the effects of the self-generated intensive electrical field and stress.Connected with the discharge model and external circuit, the whole transient process of PZT ceramic depoling can be investigated.The results show the finite transition velocity of the ferroelectric phase and the double wave structure caused by phase transition.Simulated currents are compared with the results from experiments with shock pressures varying from 0.4 to 2.8GPa.

  18. MEMS-based thick film PZT vibrational energy harvester

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Thyssen, Anders

    2011-01-01

    We present a MEMS-based unimorph silicon/PZT thick film vibrational energy harvester with an integrated proof mass. We have developed a process that allows fabrication of high performance silicon based energy harvesters with a yield higher than 90%. The process comprises a KOH etch using a mechan......We present a MEMS-based unimorph silicon/PZT thick film vibrational energy harvester with an integrated proof mass. We have developed a process that allows fabrication of high performance silicon based energy harvesters with a yield higher than 90%. The process comprises a KOH etch using...... a mechanical front side protection of an SOI wafer with screen printed PZT thick film. The fabricated harvester device produces 14.0 μW with an optimal resistive load of 100 kΩ from 1g (g=9.81 m s-2) input acceleration at its resonant frequency of 235 Hz....

  19. Piezoelectric and mechanical properties of fatigue resistant, self-healing PZT-ionomer composites

    NARCIS (Netherlands)

    James, N.K.; Lafont, U.; Zwaag, S. van der; Groen, W.A.

    2014-01-01

    Piezoelectric ceramic-polymer composites with 0-3 connectivity were fabricated using lead zirconium titanate (PZT) powder dispersed in an ionomer (Zn ionomer) and its reference ethylene methacrylic acid copolymer (EMAA) polymer matrix. The PZT-Zn ionomer and PZT-EMAA composites were prepared by melt

  20. Study of pyroelectric activity of PZT/PVDF-HFP composite

    OpenAIRE

    Luiz Francisco Malmonge; José Antonio Malmonge; Walter Katsumi Sakamoto

    2003-01-01

    Flexible, free-standing piezo and pyroelectric composite with 0 to 3 connectivity was made up from Lead Zirconate Titanate (PZT) powder and poly(vinylidene fluoride-hexafluoropropylene) (PVDF-HFP) copolymer. The pyroelectric and the piezoelectric longitudinal (d33) coefficients were measured. A 50/50 vol.% PZT/PVDF-HFP composite resulted in piezo and pyroelectric coefficients of d33 = 25.0 pC/N and p = 4.5 × 10-4 C/m²K at 70 °C, respectively. Analysis of the complex permittivity in a wide ran...

  1. Using microwave for processing nanostructured PZT ceramics; Utilizacao de microondas no processamento de ceramicas nanoestruturadas de PZT

    Energy Technology Data Exchange (ETDEWEB)

    Lanza, A.C.; Berti, T.G.; Thomazini, D.; Gelfuso, M.V., E-mail: lanza.work@gmail.com [Universidade Federal de Itajuba (UNIFEI), MG (Brazil). Instituto de Engenharia Mecanica; Eiras, J.A. [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Dept. de Fisica

    2012-07-01

    The PZT ceramics have dielectric and piezoelectric properties of technological interest. The method of microwave assisted hydrothermal synthesis becomes interesting since it occurs in a closed environment, the low temperature and time, compared to conventional methods. In this work, PZT powders were dissolved in acid medium, and by adjusting the pH of the solutions obtained were precipitated, subjected to hydrothermal treatment at 120 °C for intervals of 15, 30 and 60 min. The powders were characterized by differential thermal and gravimetric analysis, X-ray diffraction and scanning electron microscopy. The results confirm the formation of PZT phase in one hour with particle size around 55 nm, showing the feasibility of the proposed method. (author)

  2. Synthesis and characterization of tungsten or calcium doped PZT ceramics; Sintese e caracterizacao do PZT dopado com W ou Ca

    Energy Technology Data Exchange (ETDEWEB)

    Santos, D.M.; Caracas, L.B.; Noronha, R.G.; Santos, M.M.T. dos [Universidade Federal do Maranhao (UFMA), Sao Luis, MA (Brazil). Dept. de Desenho e Tecnologia. Curso de Desenho Industrial; Paiva-Santos, C.O., E-mail: denilson@ufma.b [Universidade Estadual Paulista (IQ/UNESP), Araraquara, SP (Brazil). Inst. de Quimica

    2009-07-01

    Pure and doped (tungsten or calcium) PZT ceramics were prepared by association of the polymeric precursor and partial oxalate method. The phase formation was investigated by thermal analysis (TG/DSC) and X-ray diffraction (XRD). The affect of W or Ca doping PZT and their electrical properties was evaluated. Substitution of W by Ti and Ca by Pb leads to an increase of Curie temperature and broadening of dielectric constant. A typical hysteresis loop was observed at room temperature and the remnant polarization was increased with the content of W and Ca. (author)

  3. Synthesis of PZT power by wet-dry method and its structure

    Institute of Scientific and Technical Information of China (English)

    汤卉; 王佳; 高维丽

    2008-01-01

    To prepare PZT powder at lower temperature, lead zirconate titanate (PZT) powder (x(Zr)/x(Ti)=56?44) was prepared by wet-dry method. Glycol was used as the solvent, and zirconium oxychloride was used as zirconium source. The properties and structure of the powder were analyzed by XRD, SEM and Sedimentograph. The effects of sintering parameter such as sintering temperature, keeping time and heating-up velocity on structure of PZT power were investigated. The results show that homogeneous PZT with single-phase perovskite structure can be obtained after sintering at 730 ℃ for 2 h, and the average size of PZT powder is about 113 nm.

  4. The Fabrication and Characterization of Piezoelectric PZT/PVDF Electrospun Nanofiber Composites

    Directory of Open Access Journals (Sweden)

    Ji Sun Yun

    2016-03-01

    Full Text Available Piezoelectric nanofiber composites of polyvinylidene fluoride (PVDF polymer and PZT (Pb(Zr0.53Ti0.47O3 ceramics were fabricated by electrospinning. The micro‐ structure of the PZT/PVDF electrospun nanofiber compo‐ sites was characterized using X-ray diffraction (XRD, scanning electron microscopy (SEM and transmission electron microscopy (TEM. The tensile properties (stress- strain curves and electrical properties (P-E hysteresis loops of the PZT/PVDF electrospun nanofiber composites were investigated as a function of PZT content from 0 wt% to 30 wt%. The results demonstrated that a PZT content of 20 wt % had enhanced tensile and piezoelectric characteristics.

  5. Characterization of PZT/PVC Composites Added with Carbon Black

    Institute of Scientific and Technical Information of China (English)

    LIU Xiaofang; XIONG Chuanxi; SUN Huajun; DONG Lijie; LI Rui; LIU Yang

    2005-01-01

    A new three-phase PZT/ C/ PVC composite comprising PZT (50vol%), nanocrystalline PVC (50 vol% ) and a small volume fraction f of carbon black (C) was prepared by the hot-pressing technique. The dielectric property of the composite as a function of the frequency and the dielectric and piezoelectric properties as a function of the volume fraction f of C were studied. The measured dielectric property demonstrates that a percolation transition occurs in the three-phase composites as in normal two-phase metal-insulator continuum media. The dielectric constant varies slightly with f at f < 0.1 and increases rapidly when f is close to the percolation threshold at 1 kHz. The optimum properties were obtained for f = 0.5 before the percolation threshold in the PZT/ C/ PVC (50/f/(50 - f) vol% ) composite with its d33 (20 pC/N) being 50% higher than that of the PZT/ PVC (50/50vol% ), and its g33(47.23 × 10-3 Vm/N) and Kp (0.25) much higher than the earlier reported values.XRD patterns and P-E hysteresis loops were used to interpret the experimental results.

  6. Preparation and Characterization of PZT films Fabricated on Si Substrate

    Institute of Scientific and Technical Information of China (English)

    YANG Ying

    2006-01-01

    Lead zirconium titanate (PZT) films (Zr/Ti=45:55)with a high dielectric constant are prepared successfully on the low-resistance Si substrate in sol-gel dip-coating process with PT film used as the buffer layer.The dielectric and ferroelectric properties of the films as well as the relationship between crystallization and preparing condition are studied.It is shown that the PZT ferroelectric thin films with a (110) preferred orientation and a well-crystallized perovskite structure could be obtained after annealing at 800℃ for 15 min.The particle size of the sample is about 14-25 nm.The P-E hysteresis loops are measured by means of the Sawyer-Tower test system with a compensation resistor at room temperature.The remanent polarization (Pr) and coercive electric field (Ec) of the measured PZT thin films are 47.7 μC/cm2 and 18 kV/cm,respectively.The relative dielectric constant εr and the dissipation factor tgδ of the PZT thin films were measured with an LCR meter and were found to be 158 and 0.04-0.005,respectively.

  7. Specific Heat, Charge Release and Dielectric Constant of PZT Ceramics

    NARCIS (Netherlands)

    Cereceda, N.; Noheda, B.; Gonzalo, J.A.; Mielcarek, S.; Mroz, B.

    1998-01-01

    Dielectric constant, specific heat and charge release measurements have been performed to study the FRL-FRH and FRH-PC phase transitions in Zr rich PZT (PbZr1-xTixO3). Both transitions have been described together by means of a two order parameters effective field model, in order to include the

  8. Presentation and characterization of novel thick-film PZT microactuators

    Energy Technology Data Exchange (ETDEWEB)

    Chalvet, Vincent; Habineza, Didace, E-mail: didace.habineza@femto-st.fr; Rakotondrabe, Micky; Clévy, Cédric

    2016-04-01

    We propose in this paper the characterization of a new generation of piezoelectric cantilevers called thick-films piezoelectric actuators. Based on the bonding and thinning process of a bulk PZT layer onto a silicon layer, these cantilevers can provide better static and dynamic performances compared to traditional piezocantilevers, additionally to the small dimensions.

  9. Triaxial MEMS accelerometer with screen printed PZT thick film

    DEFF Research Database (Denmark)

    Hindrichsen, Christian Carstensen; Almind, Ninia Sejersen; Brodersen, Simon Hedegaard

    2010-01-01

    . In this work integration of a screen printed piezoelectric PZT thick film with silicon MEMS technology is shown. A high bandwidth triaxial accelerometer has been designed, fabricated and characterized. The voltage sensitivity is 0.31 mV/g in the vertical direction, 0.062 mV/g in the horizontal direction...

  10. Effect of External Vibration on PZT Impedance Signature.

    Science.gov (United States)

    Yang, Yaowen; Miao, Aiwei

    2008-11-01

    Piezoelectric ceramic Lead Zirconate Titanate (PZT) transducers, working on the principle of electromechanical impedance (EMI), are increasingly applied for structural health monitoring (SHM) in aerospace, civil and mechanical engineering. The PZT transducers are usually surface bonded to or embedded in a structure and subjected to actuation so as to interrogate the structure at the desired frequency range. The interrogation results in the electromechanical admittance (inverse of EMI) signatures which can be used to estimate the structural health or integrity according to the changes of the signatures. In the existing EMI method, the monitored structure is only excited by the PZT transducers for the interrogating of EMI signature, while the vibration of the structure caused by the external excitations other than the PZT actuation is not considered. However, many structures work under vibrations in practice. To monitor such structures, issues related to the effects of vibration on the EMI signature need to be addressed because these effects may lead to misinterpretation of the structural health. This paper develops an EMI model for beam structures, which takes into account the effect of beam vibration caused by the external excitations. An experimental study is carried out to verify the theoretical model. A lab size specimen with different external excitations is tested and the effect of vibration on EMI signature is discussed.

  11. Effect of External Vibration on PZT Impedance Signature

    Directory of Open Access Journals (Sweden)

    Yaowen Yang

    2008-11-01

    Full Text Available Piezoelectric ceramic Lead Zirconate Titanate (PZT transducers, working on the principle of electromechanical impedance (EMI, are increasingly applied for structural health monitoring (SHM in aerospace, civil and mechanical engineering. The PZT transducers are usually surface bonded to or embedded in a structure and subjected to actuation so as to interrogate the structure at the desired frequency range. The interrogation results in the electromechanical admittance (inverse of EMI signatures which can be used to estimate the structural health or integrity according to the changes of the signatures. In the existing EMI method, the monitored structure is only excited by the PZT transducers for the interrogating of EMI signature, while the vibration of the structure caused by the external excitations other than the PZT actuation is not considered. However, many structures work under vibrations in practice. To monitor such structures, issues related to the effects of vibration on the EMI signature need to be addressed because these effects may lead to misinterpretation of the structural health. This paper develops an EMI model for beam structures, which takes into account the effect of beam vibration caused by the external excitations. An experimental study is carried out to verify the theoretical model. A lab size specimen with different external excitations is tested and the effect of vibration on EMI signature is discussed.

  12. Dielectric properties of novel polyurethane-PZT-graphite foam composites

    Science.gov (United States)

    Tolvanen, Jarkko; Hannu, Jari; Nelo, Mikko; Juuti, Jari; Jantunen, Heli

    2016-09-01

    Flexible foam composite materials offer multiple benefits to future electronic applications as the rapid development of the electronics industry requires smaller, more efficient, and lighter materials to further develop foldable and wearable applications. The aims of this work were to examine the electrical properties of three- and four-phase novel foam composites in different conditions, find the optimal mixture for four-phase foam composites, and study the combined effects of lead zirconate titanate (PZT) and graphite fillers. The flexible and highly compressible foams were prepared in a room-temperature mixing process using polyurethane, PZT, and graphite components as well as their combinations, in which air acted as one phase. In three-phase foams the amount of PZT varied between 20 and 80 wt% and the amount of graphite, between 1 and 15 wt%. The four-phase foams were formed by adding 40 wt% of PZT while the amount of graphite ranged between 1 and 15 wt%. The presented results and materials could be utilized to develop new flexible and soft sensor applications by means of material technology.

  13. Ultrasound backscatter microscope using PZT, fine-grain PZT, and single-crystal perovskite transducers

    Science.gov (United States)

    Olbrish, Kenneth D.; Zipparo, Michael J.; Lopath, Patrick D.; Yu, Clarence; Shrout, Thomas R.; Shung, K. Kirk

    1997-04-01

    Higher frequency ultrasound is rapidly becoming an important tool for dermatologic and ophthalmologic imaging. This brings about a need for improvement in single element transducers operating in the frequency range between 40 MHz and 100 MHz. Several piezoelectric materials may yield improved performance over common lead zirconate titanate (PZT) transducers. This study investigated several different materials incorporated into single element transducers. A static ultrasonic backscatter microscope (UBM) was constructed in the laboratory. This system allowed for a comparative testing of the imaging performance of various transducers. B-mode scans made by individual transducers show differences in image resolution. Clinically, these differences may be important to allow finer detail to be observed in a structure. Not only does this work show differences between transducers constructed from various materials, but it does so in an application-based environment. Previously, only a limited number of materials were used in such a system. This study showed results from several materials that had not been demonstrated before.

  14. PZT thin films for piezoelectric MEMS mechanical energy harvesting

    Science.gov (United States)

    Yeager, Charles

    This thesis describes the optimization of piezoelectric Pb(ZrxTi 1-x)O3 (PZT) thin films for energy generation by mechanical energy harvesting, and self-powered micro-electro-mechanical systems (MEMS). For this purpose, optimization of the material was studied, as was the incorporation of piezoelectric films into low frequency mechanical harvesters. A systematic analysis of the energy harvesting figure of merit was made. As a figure of merit (e31,ƒ)2/epsilon r (transverse piezoelectric coefficient squared over relative permittivity) was utilized. PZT films of several tetragonal compositions were grown on CaF2, MgO, SrTiO3, and Si substrates, thereby separating the dependence of composition on domain orientation. To minimize artifacts associated with composition gradients, and to extend the temperature growth window, PZT films were grown by metal organic chemical vapor deposition (MOCVD). Using this method, epitaxial {001} films achieved c-domain textures above 90% on single crystal MgO and CaF2 substrates. This could be tailored via the thermal stresses established by the differences in thermal expansion coefficients of the film and the substrate. The single-domain e31,ƒ for PZT thin films was determined to exceed -12 C/m2 in the tetragonal phase field for x ≥ 0.19, nearly twice the phenomenologically modeled value. The utilization of c-domain PZT films is motivated by a figure of merit above 0.8 C2/m4 for (001) PZT thin films. Increases to the FoM via doping and hot poling were also quantified; a 1% Mn doping reduced epsilonr by 20% without decreasing the piezoelectric coefficient. Hot poling a device for one hour above 120°C also resulted in a 20% reduction in epsilonr ; furthermore, 1% Mn doping reduced epsilonr by another 12% upon hot poling. Two methods for fabricating thin film mechanical energy harvesting devices were investigated. It was found that phosphoric acid solutions could be used to pattern MgO crystals, but this was typically accompanied by

  15. Far infrared and Raman response in tetragonal PZT ceramic films

    Energy Technology Data Exchange (ETDEWEB)

    Buixaderas, E.; Kadlec, C.; Vanek, P.; Drnovsek, S.; Ursic, H.; Malic, B.

    2015-07-01

    PbZr{sub 0}.38Ti{sub 0}.62O{sub 3} and PbZr{sub 0}.36Ti{sub 0}.64{sub O}3 thick films deposited by screen printing on (0 0 0 1) single crystal sapphire substrates and prepared at two different sintering temperatures, were studied by Fourier-transform infrared reflectivity, time-domain TH{sub z} transmission spectroscopy and micro-Raman spectroscopy. The dielectric response is discussed using the Lichtenecker model to account for the porosity of the films and to obtain the dense bulk dielectric functions. Results are compared with bulk tetragonal PZT 42/58 ceramics. The dynamic response in the films is dominated by an overdamped lead-based vibration in the TH{sub z} range, as known in PZT, but its evaluated dielectric contribution is affected by the porosity and roughness of the surface. (Author)

  16. Piezoelectric Energy Harvesting Using PZT Bimorphs and Multilayered Stacks

    Science.gov (United States)

    Panda, Prasanta Kumar; Sahoo, Benudhar; Chandraiah, M.; Raghavan, Sreekumari; Manoj, Bindu; Ramakrishna, J.; Kiran, P.

    2015-11-01

    Piezoelectric materials have a unique ability to interchange electrical and mechanical energy. This property allows the absorption of mechanical energy such as ambient vibration and its transformation into electrical energy. The electrical energy generated can be used to power low-power electronic devices. In the present study, energy harvesting by lead zirconate titanate (PZT) multilayer (ML) stacks and bimorphs is presented. The devices were fabricated by a tape casting technique and were poled at 2 kV/mm for 30 min immersed in a silicone oil bath maintained at 60°C. The energy harvesting characteristics of the fabricated devices were measured in a suitably assembled test setup. The output voltage obtained from the PZT bimorphs and ML stacks was 450 mV and 125 mV, respectively. The higher output voltage from the bimorph is due to its low capacitance.

  17. Tape Casting of Honeywell PZT Type III Powder.

    Science.gov (United States)

    1984-02-01

    STANDARDS 193 A . . . • . .I-" ’ .7. ’. .. ’. .-7 . • " U) 1 IV. Tape Casting of Honeywell PZT Type III Poder II~ II * I S Gordon 0. Dayton Beth A. Jones...Street Port Hueneme, CA 93043 Arlington, VA 22217 3 ATTN: Materials Division Attn: Code 431 Naval Research Laboratory Naval Electronics Laboratory...Washington, DC 20375 San Diego, CA 92152 ATTN: Codes 6000 1 ATTN: Electron Materials 6300 1 Sciences Division 2627 1 Naval Air Development Center Naval

  18. Characterisation of static actuation behaviour of encapsulated PZT

    Science.gov (United States)

    Doran, Conrad J.; Butler, Raymond J.

    1994-09-01

    Within the field of 'smart' structures considerable interest has been shown in the use of piezoelectric materials both as sensors and actuators. One of the best characterized of these materials is the family of Lead Zirconate Titanate (PZT) based ceramics. The use of PZT in intelligent systems has been fairly widespread, the high modulus of the material give high authority actuation, coupled with a wide operational bandwidth and relative ease of control by the application of an applied voltage. The linearity of the actuation response over a limited range has made PZT a popular choice for high precision, relatively low displacement applications. A number of attempts have been made to utilize such actuators for aerospace, using both surface mounting [1] and embedding techniques [2,3]. The effects of actuators on aeroelastic performance has also been investigated for aerospace applications [4,5]. The current practical solution to this problem appears to be the use of spatially distributed actuators [6]. One of the practical limitations of this problem are the large number of actuators required to produce the required degree of static control. In order to ensure accurate shape control, measurements must be taken to ensure there are no significant difference in the actuator element properties due to factors such as batch processing variation. In the past this has proved difficult due to the extremely brittle nature of the actuator material. More specifically the requirement for thinner elements for use in embedded applications has increased this problem. A method by which the static performance of electroceramic actuators could be quickly established would therefore be desirable. This paper presents the results of recent work to develop a test method to define the static electromechanical properties of encapsulated actuator materials in order to assess their suitability as static actuators for aerospace applications. Preliminary results using a standard PZT material are

  19. Electromechanical Properties of Microcantilever Actuated by Enhanced Piezoelectric PZT Thick Film

    Institute of Scientific and Technical Information of China (English)

    LIU Hong-Mei; ZHAO Quan-Liang; CAO Mao-Sheng; YUAN Jie; DUAN Zhong-Xia; QIU Cheng-Jun

    2008-01-01

    Pb(Zro.53,Tio.47)O3 (PZT) films with thicknesses of 0.8μm, 2μm and 4μm are prepared by a sol-gel method and their longitudinal piezoelectric coefficients are analysed. The results show that the PZT thick films, whose density is closer to bulk PZT, has the better crystallization, with d33 and density much larger than those of PZT thin films. A piezoelectric microcantilever actuated by a 4-μm-thick PZT film is fabricated and its displacement is measured in different frequencies and voltages. The displacement increases linearly with the increasing bias,and the maximum displacement of 0.544 μm is observed at 30kHz for 5V bias. The resonant frequency obtained in the experiment matches quite well with the theoretical result, and it is shown that the resonant frequency of PZT microcantilever could be controlled and predicated.

  20. Performance of magnetoelectric PZT/Ni multiferroic system for energy harvesting application

    Science.gov (United States)

    Gupta, Reema; Tomar, Monika; Kumar, Ashok; Gupta, Vinay

    2017-03-01

    Magnetoelectric (ME) coefficient of Lead Zirconium Titanate (PZT) thin films has been probed for possible energy harvesting applications. Single phase PZT thin films have been deposited on nickel substrate (PZT/Ni) using pulsed laser deposition (PLD) technique. The effect of PLD process parameters on the ME coupling coefficient in the prepared systems has been investigated. The as grown PZT films on Ni substrate were found to be polycrystalline with improved ferroelectric and ferromagnetic properties. The electrical switching behavior of the PZT thin films were verified using capacitance voltage measurements, where well defined butterfly loops were obtained. The ME coupling coefficient was estimated to be in the range of 94.5 V cm‑1 Oe‑1–130.5 V cm‑1 Oe‑1 for PZT/Ni system, which is large enough for harnessing electromagnetic energy for subsequent applications.

  1. Modeling the thermal behavior of PZT patches during the manufacturing process of smart thermoplastic structures

    Science.gov (United States)

    Elsoufi, L.; Khalil, K.; Lachat, R.; Charon, W.

    2007-08-01

    This paper concerns the manufacturing processes of thermoplastic structures including piezoceramic patches (PZT). The objective of the study reported here was to find a trade-off between the manufacturing conditions and the thermal endurance of the PZT patches. We studied the influence of high temperatures on the PZT efficiency during manufacturing. Two processes were considered: injection molding and thermoforming. The studied object consists of a polypropylene plate containing a PZT patch integrated at different positions. On the one hand, we simulated with ANSYS the thermal transient effects to study the PZT cooling according to the time of its exposure to heat for different fabrication cases and with different manufacturing processes. On the other hand, the loss in PZT generated voltage according to the temperature increment was measured by thermo-mechanical experiences using a dynamical-mechanical analysis machine (DMA) connected to an acquisition chain.

  2. Piezoelectric characteristics of PZT thin films on polymer substrate

    Science.gov (United States)

    Kang, Min-Gyu; Do, Younh-Ho; Oh, Seung-Min; Rahayu, Rheza; Kim, Yiyein; Kang, Chong-Yun; Nahm, Sahn; Yoon, Seok-Jin

    2012-02-01

    The goal of piezoelectric energy harvesting is to improve the power efficiency of devices. One of the approaches for the improvement of power efficiency is to apply the large strain on the piezoelectric materials and then many scientists approached using thin films or nano-structured piezoelectric materials to obtain flexibility. However, the conventional thin film processes available for the fabrication of piezoelectric materials as PbZr0.52Ti0.48O3 (PZT) are not compatible with flexible electronics because they require high processing temperatures (>700^oC) to obtain piezoelectricity. Excimer laser annealing (ELA) is attractive heat process for the low-temperature crystallization, because of its material selectivity and short heating time. In this study, the amorphous PZT thin films were deposited on polymer substrate by rf-sputtering. To crystallize the amorphous films, the ELA was carried out with various conditions as function of the applied laser energy density, the number of pulse, and the repetition rate. To evaluate the piezoelectric characteristics, piezoelectric force microscopy (PFM) and electrometer are used. As a result, we obtained the crystallized PZT thin film on flexible substrate and obtained flexible piezoelectric energy harvester.

  3. Broadband Electromagnetic Emission from PZT Ferroelectric Ceramics after Shock Loading

    Directory of Open Access Journals (Sweden)

    Fiodoras ANISIMOVAS

    2013-12-01

    Full Text Available It was experimentally registered pulsed electromagnetic (EM radiation in frequency range higher than television one using wideband horns with coaxial and waveguide outputs. The EM radiation was received during shock loading of lead zirconate titanate (PZT ceramics cylinders in conventional piezoelectric ignition mechanisms. Digital oscilloscope allows registering whole series of EM pulses and each pulse from the series transmitted from horn antenna of (1 – 18 GHz operating band frequencies. There is (1 – 4 ms delay between the shock and the first pulse of the series. Duration of the series is about (3 – 4 ms. The PZT cylinders were cleaved along their axes and the surfaces formed in the process were investigated by scanning electron microscope. It was concluded that from electrical point of view PZT ceramics contain interacting subsystems. It was found that EM radiation spectrum of pulse detected by waveguide detector heads has harmonics reaching 80 GHz. Presence of harmonics higher than 20 GHz indicates on radiation due to deceleration of electrons emitted during the switching. The EM pulses in the series appear randomly and have different amplitudes which partly confirmed thesis on independent switching dynamics of small volumes governed by a local electric field.DOI: http://dx.doi.org/10.5755/j01.ms.19.4.3137

  4. TEMPLATE-ASSISTED FABRICATION AND DIELECTROPHORETIC MANIPULATION OF PZT MICROTUBES

    Directory of Open Access Journals (Sweden)

    VLADIMÍR KOVAĽ

    2012-09-01

    Full Text Available Mesoscopic high aspect ratio ferroelectric tube structures of a diverse range of compositions with tailored physical properties can be used as key components in miniaturized flexible electronics, nano- and micro-electro-mechanical systems, nonvolatile FeRAM memories, and tunable photonic applications. They are usually produced through advanced “bottom-up” or “topdown” fabrication techniques. In this study, a template wetting approach is employed for fabrication of Pb(Zr0.52Ti0.48O3 (PZT microtubes. The method is based on repeated infiltration of precursor solution into macroporous silicon (Si templates at a sub-atmospheric pressure. Prior to crystallization at 750°C, free-standing tubes of a 2-μm outer diameter, extending to over 30 μm in length were released from the Si template using a selective isotropic-pulsed XeF2 reactive ion etching. To facilitate rapid electrical characterization and enable future integration process, directed positioning and aligning of the PZT tubes was performed by dielectrophoresis. The electric field-assisted technique involves an alternating electric voltage that is applied through pre-patterned microelectrodes to a colloidal suspension of PZT tubes dispersed in isopropyl alcohol. The most efficient biasing for the assembly of tubes across the electrode gap of 12 μm was a square wave signal of 5 Vrms and 10 Hz. By varying the applied frequency in between 1 and 10 Hz, an enhancement in tube alignment was obtained.

  5. Strong nonlinear harmonic generation in a PZT/Aluminum resonator

    Energy Technology Data Exchange (ETDEWEB)

    Parenthoine, D; Haumesser, L; Meulen, F Vander; Tran-Huu-Hue, L-P, E-mail: parenthoine@univ-tours.f [University Francois Rabelais of Tours, U 930 Imagerie et Cerveau, CNRS 2448, ENIVL, rue de la Chocolaterie, BP 3410, 41034 Blois (France)

    2009-11-01

    In this work, the extentional vibration mode of a coupled PZT/ Aluminum rod resonator is studied experimentally. Geometrical characteristics of the PZT are its 27 mm length and its 4x4 mm{sup 2} cross section area. The excitation voltage consists in sinusoidal bursts in the frequency range (20-80 kHz). Velocity measurements are performed at both ends of this system, using a laser probe. Strong harmonic distortions in the mechanical response (up to -20 dB with respect to the primary wave amplitude) have been observed. The corresponding input levels are far lower than those which are necessary to observe quadratic second harmonic generation in a free PZT resonator. The strong nonlinear effect can be explained as a super-harmonic resonance of the system due to a specific ratio between the eigen frequencies of the two parts of the resonator. Evolution of fundamental and harmonic responses are observed as a function of input levels, highlighting hysteretic behavior.

  6. Broadband Electromagnetic Emission from PZT Ferroelectric Ceramics after Shock Loading

    Directory of Open Access Journals (Sweden)

    Fiodoras ANISIMOVAS

    2013-12-01

    Full Text Available It was experimentally registered pulsed electromagnetic (EM radiation in frequency range higher than television one using wideband horns with coaxial and waveguide outputs. The EM radiation was received during shock loading of lead zirconate titanate (PZT ceramics cylinders in conventional piezoelectric ignition mechanisms. Digital oscilloscope allows registering whole series of EM pulses and each pulse from the series transmitted from horn antenna of (1 – 18 GHz operating band frequencies. There is (1 – 4 ms delay between the shock and the first pulse of the series. Duration of the series is about (3 – 4 ms. The PZT cylinders were cleaved along their axes and the surfaces formed in the process were investigated by scanning electron microscope. It was concluded that from electrical point of view PZT ceramics contain interacting subsystems. It was found that EM radiation spectrum of pulse detected by waveguide detector heads has harmonics reaching 80 GHz. Presence of harmonics higher than 20 GHz indicates on radiation due to deceleration of electrons emitted during the switching. The EM pulses in the series appear randomly and have different amplitudes which partly confirmed thesis on independent switching dynamics of small volumes governed by a local electric field.DOI: http://dx.doi.org/10.5755/j01.ms.19.4.3137

  7. The Fabrication and Characterization of Piezoelectric PZT/PVDF Electrospun Nanofiber Composites

    OpenAIRE

    Ji Sun Yun; Chun Kil Park; Young Hun Jeong; Jeong Ho Cho; Jong-Hoo Paik; Sun Hong Yoon; Kyung-Ran Hwang

    2016-01-01

    Piezoelectric nanofiber composites of polyvinylidene fluoride (PVDF) polymer and PZT (Pb(Zr0.53Ti0.47)O3) ceramics were fabricated by electrospinning. The micro‐ structure of the PZT/PVDF electrospun nanofiber compo‐ sites was characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The tensile properties (stress- strain curves) and electrical properties (P-E hysteresis loops) of the PZT/PVDF electrospun nanofiber composites w...

  8. Highly-efficient, flexible piezoelectric PZT thin film nanogenerator on plastic substrates.

    Science.gov (United States)

    Park, Kwi-Il; Son, Jung Hwan; Hwang, Geon-Tae; Jeong, Chang Kyu; Ryu, Jungho; Koo, Min; Choi, Insung; Lee, Seung Hyun; Byun, Myunghwan; Wang, Zhong Lin; Lee, Keon Jae

    2014-04-23

    A highly-efficient, flexible piezoelectric PZT thin film nanogenerator is demonstrated using a laser lift-off (LLO) process. The PZT thin film nanogenerator harvests the highest output performance of ∼200 V and ∼150 μA·cm(-2) from regular bending motions. Furthermore, power sources generated from a PZT thin film nanogenerator, driven by slight human finger bending motions, successfully operate over 100 LEDs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. An Unconventional Inchworm Actuator Based on PZT/ERFs Control Technology

    OpenAIRE

    Guojun Liu; Yanyan Zhang; Jianfang Liu; Jianqiao Li; Chunxiu Tang; Tengfei Wang; Xuhao Yang

    2016-01-01

    An unconventional inchworm actuator for precision positioning based on piezoelectric (PZT) actuation and electrorheological fluids (ERFs) control technology is presented. The actuator consists of actuation unit (PZT stack pump), fluid control unit (ERFs valve), and execution unit (hydraulic actuator). In view of smaller deformation of PZT stack, a new structure is designed for actuation unit, which integrates the advantages of two modes (namely, diaphragm type and piston type) of the volume c...

  10. Sensitivity of PZT Impedance Sensors for Damage Detection of Concrete Structures

    Directory of Open Access Journals (Sweden)

    Yong Lu

    2008-01-01

    Full Text Available Piezoelectric ceramic Lead Zirconate Titanate (PZT based electro-mechanicalimpedance (EMI technique for structural health monitoring (SHM has been successfullyapplied to various engineering systems. However, fundamental research work on thesensitivity of the PZT impedance sensors for damage detection is still in need. In thetraditional EMI method, the PZT electro-mechanical (EM admittance (inverse of theimpedance is used as damage indicator, which is difficult to specify the effect of damage onstructural properties. This paper uses the structural mechanical impedance (SMI extractedfrom the PZT EM admittance signature as the damage indicator. A comparison study on thesensitivity of the EM admittance and the structural mechanical impedance to the damages ina concrete structure is conducted. Results show that the SMI is more sensitive to the damagethan the EM admittance thus a better indicator for damage detection. Furthermore, this paperproposes a dynamic system consisting of a number of single-degree-of-freedom elementswith mass, spring and damper components to model the SMI. A genetic algorithm isemployed to search for the optimal value of the unknown parameters in the dynamic system.An experiment is carried out on a two-storey concrete frame subjected to base vibrations thatsimulate earthquake. A number of PZT sensors are regularly arrayed and bonded to the framestructure to acquire PZT EM admittance signatures. The relationship between the damageindex and the distance of the PZT sensor from the damage is studied. Consequently, thesensitivity of the PZT sensors is discussed and their sensing region in concrete is derived.

  11. Investigation of Top/Bottom electrode and Diffusion Barrier Layer for PZT Thick Film MEMS Sensors

    DEFF Research Database (Denmark)

    Hindrichsen, Christian Carstensen; Pedersen, Thomas; Thomsen, Erik Vilain

    2008-01-01

    Top and bottom electrodes for screen printed piezoelectric lead zirconate titanate, Pb(ZrxTi1 - x)O3 (PZT) thick film are investigated with respect to future MEMS devices. Down to 100 nm thick E-beam evaporated Al and Pt films are patterned as top electrodes on the PZT using a lift-off process...

  12. Investigation of top electrode for PZT thick films based MEMS sensors

    DEFF Research Database (Denmark)

    Hindrichsen, Christian Carstensen; Pedersen, Thomas; Kristiansen, Paw T.;

    2010-01-01

    In this work processing of screen printed piezoelectric PZT thick films on silicon substrates is investigated for use in future MEMS devices. E-beam evaporated Al and Pt are patterned on PZT as a top electrode using a lift-off process with a line width down to 3 mu m. Three test structures are used...

  13. Thin Film PZT Piezo MEMS for Micro-Robotic Angular Rate Sensing and Rotary Actuation

    Science.gov (United States)

    2012-07-31

    Luz Sanchez, Rob Proie, Vishnu Ganesan, Joe Conroy, and Ron Polcawich July 31, 2012 U.S. Army Research Laboratory THIN FILM PZT PIEZO MEMS FOR...Caltech Angular rate sensing on 1-30 mg platform • 2 orders smaller than packaged state of the art gyroscope. • Integrated biomimetic PZT actuator

  14. Fabrication and comparison of PMN-PT single crystal, PZT and PZT-based 1-3 composite ultrasonic transducers for NDE applications.

    Science.gov (United States)

    Kim, Ki-Bok; Hsu, David K; Ahn, Bongyoung; Kim, Young-Gil; Barnard, Daniel J

    2010-08-01

    This paper describes fabrication and comparison of PMN-PT single crystal, PZT, and PZT-based 1-3 composite ultrasonic transducers for NDE applications. As a front matching layer between test material (Austenite stainless steel, SUS316) and piezoelectric materials, alumina ceramics was selected. The appropriate acoustic impedance of the backing materials for each transducer was determined based on the results of KLM model simulation. Prototype ultrasonic transducers with the center frequencies of approximately 2.25 and 5MHz for contact measurement were fabricated and compared to each other. The PMN-PT single crystal ultrasonic transducer shows considerably improved performance in sensitivity over the PZT and PZT-based 1-3 composite ultrasonic transducers.

  15. Impedance-Based Cable Force Monitoring in Tendon-Anchorage Using Portable PZT-Interface Technique

    Directory of Open Access Journals (Sweden)

    Thanh-Canh Huynh

    2014-01-01

    Full Text Available In this paper, a portable PZT interface for tension force monitoring in the cable-anchorage subsystem is developed. Firstly, the theoretical background of the impedance-based method is presented. A few damage evaluation approaches are outlined to quantify the variation of impedance signatures. Secondly, a portable PZT interface is designed to monitor impedance signatures from the cable-anchorage subsystem. One degree-of-freedom analytical model of the PZT interface is established to explain how to represent the loss of cable force from the change in the electromechanical impedance of the PZT interface as well as reducing the sensitive frequency band by implementing the interface device. Finally, the applicability of the proposed PZT-interface technique is experimentally evaluated for cable force-loss monitoring in a lab-scaled test structure.

  16. A new three-dimensional electromechanical impedance model for an embedded dual-PZT transducer

    Science.gov (United States)

    Wang, Dansheng; Li, Zhi; Zhu, Hongping

    2016-07-01

    In the past twenty years, the electromechanical (EM) impedance technique has been investigated extensively in the mechanical, aviation and civil engineering fields. Many different EM impedance models have been proposed to characterize the interaction between the surface-bonded PZT transducer and the host structure. This paper formulates a new three-dimensional EM impedance model characterizing the interaction between an embedded circle dual-PZT transducer and the host structure based on the effective impedance concept. The proposed model is validated by experimental results from a group of smart cement cubes, in which three circle dual-PZT transducers are embedded respectively. In addition, a new EM impedance measuring method for the dual-PZT transducer is also introduced. In the measuring method, only a common signal generator and an oscilloscope are needed, by which the exciting and receiving voltage signals are obtained respectively. Combined with fast Fourier transform the EM impedance signatures of the dual-PZT transducers are obtained.

  17. Temperature effects on the mechanical behaviour of PZT 95/5

    Science.gov (United States)

    Khan, A. S.; Balzer, J. E.; Wilgeroth, J. M.; Proud, W. G.

    2014-05-01

    This research is to develop a better understanding of the piezoelectric ceramic lead zirconate titanate (PZT) 95/5 with varying temperatures, porosities and strain rates. Here, unpoled PZT samples of two different porosities were subjected to a range of compression rates, using quasi-static loading equipment, drop-weight towers and Split Hopkinson Pressure Bars (SHPBs). Varying temperatures were achieved using purpose-made environmental chambers. The resulting stress-strain relationships are compared. The samples were square tiles, 7.5 × 7.5 mm and 3 mm thickness. The density of the standard PZT used here was 7.75 g cm-3 (henceforth described as PZT), whilst the density of the higher porosity PZT was 7.38 g cm-3 (henceforth described as PPZT). This research is part of a wider study.

  18. Experimental Study on Abrasive Water Jet Machining of PZT Ceramic

    Science.gov (United States)

    Dhanawade, Ajit; Upadhyai, Ravi; Rouniyar, Arunkumar; Kumar, Shailendra

    2017-07-01

    This paper presents research work involved in abrasive water jet machining of PZT ceramic material. Process parameters namely stand-off distance, water pressure and traverse rate are considered in the present study. Response surface methodology approach is used to design the experiments. Relative significance of process parameters and their influence on kerf properties are identified on the basis of analysis of variance. It is found that water pressure and traverse rate are most significant parameters followed by stand-off distance. On the basis of experimental analysis, regression models are developed to predict kerf taper and depth of cut. The models are developed with respect to significant parameters, interaction and quadratic terms. It is found that model predictions are in congruence with experimental results. Multi-response optimization of process parameters is also performed using desirability approach in order to minimize kerf taper and maximize depth of cut. Kerf wall features of machined surfaces are observed using scanning electron microscope. The findings of present study are useful to improve kerf properties in abrasive water jet machining of PZT ceramic materials.

  19. Crack detection of railway turnouts using PZT sensors (presentation video)

    Science.gov (United States)

    Ni, Yiqing; Li, Z. G.; Wu, F.

    2014-05-01

    Railway turnouts (railroad switches) are the weakest components of a rail track system. Cracks may occur in the railway turnouts due to cyclic loadings and impact loadings imposed by passing trains. It is of great significance to continuously monitor the health condition of the railway turnouts and promptly detect crack once it initiates. It is well-known that acoustic emission (AE) signals are generated when a crack initiates and propagates. Detecting the high-frequency AE signals by piezoelectric sensors can help identify the crack and its location. This paper reports the design and implementation of a PZT-based system for crack monitoring of railway turnouts. This online monitoring system is activated for signal collection by a trigger system when a train is arriving to pass through the instrumented railway turnout. It mainly detects the AE signals generated when a crack initiates during the train passage or when the initiated crack expands during the passage of a heavy haul wagon. This system has been installed on a railroad line for over one year and has successfully detected the damage occurring at a railroad switch during its service period. This paper also briefs a guided-wave-based system for monitoring of micro-cracks in rail tracks by integrating FBG and PZT sensors.

  20. A biaxial PZT optical scanner for pico-projector applications

    Science.gov (United States)

    Ikegami, K.; Koyama, T.; Saito, T.; Yasuda, Y.; Toshiyoshi, H.

    2015-02-01

    We report a newly developed two-dimensional MEMS optical scanner based on the ADRIP (Arc Discharge Reactive Ion-Plating) deposited piezoelectric PZT film of typical 4 μm. A circular mirror of 1.2 mm in diameter is suspended within a pair of resonant mechanism that oscillates at 25 kHz for ±12° mechanical angle with a typical voltage of 10 V. A gimbal plate including the mirror is supported with another pair of meandering suspensions to tilt the plate in the orthogonal direction at 60 Hz for the off-resonant vertical motion of ±8° mechanical. Overall power consumption of the piezoelectric actuation was 100 mW or less. As a mechanical reinforce, a rib-structure was designed on the backside of the mirror by using a structural optimization tool TOSCA to suppress the dynamic curvature to 100 nm or less. A piezoelectric sensor was also integrated in the identical PZT film after optimizing the electrode shape to pick up the mechanical angle of the scanner and to give a trigger signal to the control system. A plug-in type pico-projector optics and electronics has been assembled in a 7.5 cm × 12 cm × 5 cm volume with RGB lasers to demonstrate a HD (high definition) class image projection of 720 horizontal lines. The fundamental resonance of the entire scanner mechanism was made to be 1 kHz or higher, thereby exhibiting a compatibility with vehicle applications.

  1. Poling process optimization of piezo nano composite PZT/polimer

    Science.gov (United States)

    Ridlo, M. Rosyid; Lestari, Titik; Mardiyanto, Oemry, Achiar

    2013-09-01

    The objective of poling process is to make the electric dipole directions to be parallel in the inside perovskite crystal of piezo materials. In simply way, poling was carried out by giving the two sides of a piezo material by highly electrical potential. More parallel of electrical dipoles, it is more strength the piezo characteristics. The optimization involved control of temperature, time depth and the electrical voltage. The samples was prepared by solgel method with precursor tetrabutyl titanat Ti(OC4H9)4, zirconium nitrat Zr(NO3)4ṡ5H2O, Pb(CH3COO)2ṡ3H2O and solution ethylene glycol. Molar ratio Pb:Zr:Ti = 1,1:0,52:0,48 with concidering lossed Pb. Result of solgel process is nano powder PZT. The formed nano powder PZT was then mixed with polimer PVDF and pressed 10 MPa at 150 °C with the size 15 mm in diameter. After poling, piezoelectric constant d33 was measured. The highest d33 = 45 pC/N was found at poling parameters V = 5 kV/ mm, T = 120 °C dan time depth = 1 hours.

  2. Ferroelectric/electrode interfaces: Polarization switching and reliability of PZT capacitors in nonvolatile memories

    Science.gov (United States)

    Chen, Ye (Mike)

    The objective of this work was to investigate how the interface between electrode and PZT influences the PZT capacitor reliability. In order to conduct a well controlled experiment only the top-electrode PZT film interface was modified to study its effect on switching characteristics (i.e. hysteresis loop), voltage switching endurance and polarization retention of state of the art MOCVD grown film (nominally identical). The polycrystalline PZT film (50 -- 90 nm thick) are dominantly tetragonal with small fractions of the rhombohedral phase. XPS analyses of the as-deposited PZT film found the existence of a Pb-rich carbonate surface layer on all PZT film provided by industrial collaborators. Using materials characterizations such as in-situ XPS and ARXPS in tandem with electrical measurements it was determined that the Pb-rich surface layer appears to be an engineered sacrificial layer, which is beneficial in maximizing the switchable polarization and in improving the endurance and opposite-state retention behavior of PZT based FRAM capacitors with Pt electrode. This is because the excess Pb on the PZT surface and the Pb in the surface PZT reacts readily with the Pt during the Pt top electrode deposition creating a Pb-deficient non-ferroelectric interface layer between the top electrode and the PZT film. ARXPS analyses showed that this defective layer was approximately one nanometer thick and this is consistent with the hysteresis loop measurements that indicated a similar interface layer thickness. Inferior switching endurance and polarization retention was found in PZT film with an engineered initial thicker defective interface layer (via a HNO3-clean of the PZT surface prior to the top electrode deposition). This could be due to the fact that this defective interface layer may have thickened during the voltage cycling and/or retention bake. The thickening could be caused by greater carrier trapping and/or interface reaction between the Pb and the Pt. This

  3. A new traveling wave ultrasonic motor using thick ring stator with nested PZT excitation.

    Science.gov (United States)

    Chen, Weishan; Shi, Shengjun; Liu, Yingxiang; Li, Pei

    2010-05-01

    To avoid the disadvantages of conventional traveling wave ultrasonic motors--lower efficiency PZT working mode of d(31), fragility of the PZT element under strong excitation, fatigue of the adhesive layer under harsh environmental conditions, and low volume of the PZT material in the stator--a new type of traveling wave ultrasonic motor is presented in this paper. Here we implement the stator by nesting 64 PZT stacks in 64 slots specifically cut in a thick metal ring and 64 block springs nested within another 64 slots to produce preloading on the PZT stacks. In this new design, the d33 mode of the PZT is used to excite the flexural vibrations of the stator, and fragility of the PZT ceramics and fatigue of the adhesive layer are no longer an issue. The working principle, FEM simulation, fabrication, and performance measurements of a prototype motor were demonstrated to validate the proposed ideas. Typical output of the prototype motor is no-load speed of 15 rpm and maximum torque of 7.96 N x m. Further improvement will potentially enhance its features by increasing the accuracy in fabrication and adopting appropriate frictional material into the interface between the stator and the rotor.

  4. Properties of RF-Sputtered PZT Thin Films with Ti/Pt Electrodes

    Directory of Open Access Journals (Sweden)

    Cui Yan

    2014-01-01

    Full Text Available Effect of annealing temperature and thin film thickness on properties of Pb(Zr0.53Ti0.47O3 (PZT thin film deposited via radiofrequency magnetron sputtering technique onto Pt/Ti/SiO2/Si substrate was investigated. Average grain sizes of the PZT thin film were measured by atomic force microscope; their preferred orientation was studied through X-ray diffraction analysis. Average residual stress in the thin film was estimated according to the optimized Stoney formula, and impedance spectroscopy characterization was performed via an intelligent LCR measuring instrument. Average grain sizes of PZT thin films were 60 nm~90 nm and their average roughness was less than 2 nm. According to X-ray diffraction analysis, 600°C is the optimal annealing temperature to obtain the PZT thin film with better crystallization. Average residual stress showed that thermal mismatch was the decisive factor of residual stress in Pt/Ti/SiO2/Si substrate; the residual stress in PZT thin film decreased as their thickness increased and increased with annealing temperature. The dielectric constant and loss angle tangent were extremely increased with the thickness of PZT thin films. The capacitance of the device can be adjusted according to the thickness of PZT thin films.

  5. Plasmonic assisted two wave mixing phenomenon for energy transfer in ferroelectric PZT film

    Science.gov (United States)

    Gupta, Reema; Kumari, Satchi; Tomar, Monika; Gupta, Vinay

    2017-04-01

    Ferroelectric - photorefractive PZT thin films have been exploited to study the energy transfer using pump probe technique for the development of optical delay lines. Two-wave mixing has been studied for three different PZT thin film samples deposited using pulsed laser deposition (PLD) technique. Uniform distribution of gold micro-discs of 40 nm thickness and 120 μm diameter over the surface of PZT thin film plays a vital role in enhancing the two-wave mixing. This is due to the ferroelectric domains present in PZT thin film which get polarized as a result of excited surface plasmons at the Au-PZT interface. The dual effect leads to an enhanced energy transfer from pump to 'Probe Beam'. The maximum two-wave mixing gain was found to be about 1.185 and 1.055 respectively for gold micro-discs patterned and bare PZT thin film deposited on STO substrate. In comparison, the PZT thin film covered completely with the gold overlayer does not show any significant two wave mixing gain due to the scattering of light by Au overlayer.

  6. PZT-Polymer 1-3 Composite for High Resolution Ultrasonic Imaging

    Institute of Scientific and Technical Information of China (English)

    Shinan Wang; Jing-Feng Li; Katsuhiro Wakabayashi; Masayoshi Esashi

    2000-01-01

    @@ A novel process has been developed to construct PZT-polymer 1-3 micro composites for high-resolution ultrasonic imaging for medical diagnosis. The key technology is the lost silicon (Si) mold process, by which PZT micro-rod arrays have been successfully fabricated with the finest rod size being 7 μm, the highest aspect ratio exceeding 15. Such fine-scale high-aspect-ratio PZT structures, which are essential for realizing high imaging performance, have never been realized by any conventional technique.

  7. THE INFLUENCE OF Β-PBO2 ON PZT PHASE FORMATION

    Directory of Open Access Journals (Sweden)

    H. Allal

    2015-07-01

    Full Text Available The reactional mechanism of the formation of solid solution lead-zircono-titanate PZT has been studied using β-PbO2, TiO2 and ZrO2 as starting materials. PZT ceramics were prepared by solid state reaction between oxides at different temperatures. After calcination samples are characterized by thermogravimetry (TGA, differential thermal analysis (DTA, differential scanning, Infrared spectroscopy and x-ray diffraction (XRD. Using lead dioxide (β-PbO2 allows PZT powder to be sintered at a temperature as low as 700°C.

  8. Impedance and ferroelectric properties of Sr2+modified PZT-PMN ceramics

    Institute of Scientific and Technical Information of China (English)

    Arvind Kumar; SK Mishra

    2014-01-01

    Sr2+modified polycrystalline PZT-PMN ceramics were synthesized by a semi-wet route. Impedance spectroscopy studies indicate the bulk and grain boundary effects of PZT-PMN material along with the negative temperature coefficient of resistance. The bulk conductiv-ity exhibits an Arrhenius-type thermally activated hopping process which is supported by the AC conductivity behavior as a function of fre-quency and temperature. It is observed that the remnant polarization increases with an increase in the Sr2+content in PZT-PMN.

  9. PZT thin film deposition techniques, properties and its application in ultrasonic MEMS sensors: a review

    Science.gov (United States)

    Shilpa, G. D.; Sreelakshmi, K.; Ananthaprasad, M. G.

    2016-09-01

    This paper describes an overview of the state of art in PbZrxTi1-xO3 (PZT)ferroelectric thin films and its applications in Micro Electro Mechanical Systems (MEMS). First, the deposition techniques and then the important properties of PZT films such as surface morphology polarization and ferroelectric properties are reviewed. Two major deposition techniques such as sol-gel and Magnetron sputtering are given and compared for the film surface morphology and ferroelectric properties. Finally, the application of PZT thin film in MEMS ultrasonic sensors is discussed.

  10. Optical properties of PZT thin films deposited on a ZnO buffer layer

    OpenAIRE

    Schneider, T.; Leduc, D; Cardin, J.; LUPI, C; Barreau, N; Gundel, H.

    2015-01-01

    The optical properties of lead zirconate titanate (PZT) thin films deposited on ZnO were studied by m-lines spectroscopy. In order to retrieve the refractive index and the thickness of both layers from the m-lines spectra, we develop a numerical algorithm for the case of a two-layer system and show its robustness in the presence of noise. The sensitivity of the algorithm of the two-layer model allows us to relate the observed changes in the PZT refractive index to the PZT structural change du...

  11. Physical properties of inorganic PMW-PNN-PZT ceramics

    Science.gov (United States)

    Sin, Sang-Hoon; Yoo, Ju-hyun; Kim, Yong-Jin; Baek, Sam-ki; Ha, Jun-Soo; No, Chung-Han; Song, Hyun-Seon; Shin, Dong-Chan

    2015-07-01

    In this work, inorganic Pb(Mg1/2W1/2)0.03(Ni1/3Nb2/3)x(Zr0.5Ti0.5)0.97-xO3 (x = 0.02 ∼ 0.12) composition ceramics were fabricated by the conventional solid state reaction method. And then their micro structure and ferroelectric properties were investigated according to the amount of PNN substitution. Small amounts of Li2CO3 and CaCO3 were used in order to decrease the sintering temperature of the ceramics. The 0.10 mol PNN-substituted PMW-PNN- PZT ceramics sintered at 920°C showed the excellent physical properties of piezoelectric constant (d33), electromechanical coupling factor (kp), mechanical quality coefficient (Qm), and dielectric constant of 566 pC/N, 0.61, 73, and 2183, respectively.

  12. A Novel Integrated PZT-Driven Micropump and Microvalve

    Institute of Scientific and Technical Information of China (English)

    Zhaoxin Geng; Dafu Cui; Haining Wang; Changchun Liu; Bo Su

    2006-01-01

    According to the 'elastic buffer mechanism' and the'variable gap mechanism', a new device, which is both micropump and active microvalve actuated by PZT bimorph cantilever, was fabricated with polydimethylsiloxane (PDMS) and silicon chip. The thickness of the micropump membrance is about 180 μm. The diameter and the depth of micropump chamber cavity are 6 mm and 40 μm, respectively. The performances of the micropump, such as pump rate and backpressure, were characterized. As a flow-rectifying element, the diffusers and active valve were used instead of passive check valves. The flow rate and the backpressure of the micropump are about 420 μL/min and 2 kPa when applying a 100 V square wave driving voltage at frequency of 35 Hz.

  13. NRBS, RBS, TEM and SAED characterisation of sol-gel PZT films

    Energy Technology Data Exchange (ETDEWEB)

    Pantelica, D. [HH National Institute of Physics and Nuclear Engineering, P.O. Box MG-6 RO-077125 Bucharest-Magurele (Romania); Vasiliu, F. [National Institute of Materials Physics, P.O. Box MG-7, RO-077125 Bucharest-Magurele (Romania)]. E-mail: fvasiliu@infim.ro; Ionescu, P. [HH National Institute of Physics and Nuclear Engineering, P.O. Box MG-6 RO-077125 Bucharest-Magurele (Romania); Negoita, F. [HH National Institute of Physics and Nuclear Engineering, P.O. Box MG-6 RO-077125 Bucharest-Magurele (Romania)

    2005-10-15

    TEM-SAED investigations were performed on PZT films, to elucidate the role of pyrolysis conditions on orientation selection. For short pyrolysis, occurrence of the metastable fluorite and the interfacial Pt {sub x}Pb template layer are the factors inducing the (1 1 1) PZT orientation. For advanced pyrolysis, the TiO{sub 2} interfacial layer could be responsible for (1 0 0) PZT strong orientation. To further investigate the stoichiometry of PZT and interfacial layers, we performed heavy ion RBS and NRBS measurements. Only a substoichiometric TiO{sub 2-x} layer is found for the short pyrolized film whereas two Ti and O rich layers were observed for advanced pyrolysis. The thicker oxygen rich TiO{sub 2-x} bottom layer, observed by TEM and NRBS analysis, could lead to <1 0 0> texture, observed for oxidizing conditions at the interface during pyrolysis.

  14. Airflow energy harvesters of metal-based PZT thin films by self-excited vibration

    Science.gov (United States)

    Suwa, E.; Tsujiura, Y.; Kurokawa, F.; Hida, H.; Kanno, I.

    2014-11-01

    We developed self-excited vibration energy harvesters of Pb(Zr,Ti)O3 (PZT) thin films using airflow. To enhance the self-excited vibration, we used 30-μm-thick stainless steel (SS304) foils as base cantilevers on which PZT thin films were deposited by rf-magnetron sputtering. To compensate for the initial bending of PZT/SS304 unimorph cantilever due to the thermal stress, we deposited counter PZT thin films on the back of the SS304 cantilever. We evaluated power-generation performance and vibration mode of the energy harvester in the airflow. When the angle of attack (AOA) was 20° to 30°, large vibration was generated at wind speeds over 8 m/s. By FFT analysis, we confirmed that stable self-excited vibration was generated. At the AOA of 30°, the output power reached 19 μW at wind speeds of 12 m/s.

  15. High Quality Factor Silicon Cantilever Driven by PZT Actuator for Resonant Based Mass Detection

    CERN Document Server

    Lu, Jian; Zhang, Yi; Mihara, Takashi; Itoh, Toshihiro; Maeda, Ryutaro

    2008-01-01

    A high quality factor (Q-factor) piezoelectric lead zirconat titanate (PZT) actuated single crystal silicon cantilever was proposed in this paper for resonant based ultra-sensitive mass detection. Energy dissipation from intrinsic mechanical loss of the PZT film was successfully compressed by separating the PZT actuator from resonant structure. Excellent Q-factor, which is several times larger than conventional PZT cantilever, was achieved under both atmospheric pressure and reduced pressures. For a 30 micrometer-wide 100 micrometer-long cantilever, Q-factor was measured as high as 1113 and 7279 under the pressure of 101.2 KPa and 35 Pa, respectively. Moreover, it was found that high-mode vibration can be realized by the cantilever for the pursuit of great Q-factor, while support loss became significant because of the increased vibration amplitude at the actuation point. An optimized structure using node-point actuation was suggested then to suppress corresponding energy dissipation.

  16. Feasibility Verification of Mountable PZT-Interface for Impedance Monitoring in Tendon-Anchorage

    Directory of Open Access Journals (Sweden)

    Thanh-Canh Huynh

    2015-01-01

    Full Text Available This study has been motivated to numerically evaluate the performance of the mountable PZT-interface for impedance monitoring in tendon-anchorage. Firstly, electromechanical impedance monitoring and feature classification methods are outlined. Secondly, a structural model of tendon-anchorage subsystem with mountable PZT-interface is designed for impedance monitoring. Finally, the feasibility of the mountable PZT-interface is numerically examined. A finite element (FE model is designed for the lab-scaled tendon-anchorage. The FE model of the PZT-interface is tuned as its impedance signatures meet the experimental test results at the same frequency ranges and also with identical patterns. Equivalent model properties of the FE model corresponding to prestress forces inflicted on the lab-tested structure are identified from the fine-tuning practice.

  17. Piezoelectric and mechanical properties of fatigue resistant, self-healing PZT-ionomer composites

    Science.gov (United States)

    James, N. K.; Lafont, U.; van der Zwaag, S.; Groen, W. A.

    2014-05-01

    Piezoelectric ceramic-polymer composites with 0-3 connectivity were fabricated using lead zirconium titanate (PZT) powder dispersed in an ionomer (Zn ionomer) and its reference ethylene methacrylic acid copolymer (EMAA) polymer matrix. The PZT-Zn ionomer and PZT-EMAA composites were prepared by melt extrusion followed by hot pressing. The effects of poling conditions such as temperature, time and electric field on the piezoelectric properties of the composites were investigated. The experimentally observed piezoelectric charge coefficient and dielectric constant of the composites were compared with theoretical models. The results show that PZT-Zn ionomer composites have better piezoelectric properties compared to PZT-EMAA composites. The static and fatigue properties of the composites were investigated. The PZT-Zn ionomer composites were found to have excellent fatigue resistance even at strain levels of 4%. Due to the self-healing capabilities of the ionomer matrix, the loss of piezoelectric properties after high strain tensile cyclic loading could be partially recovered by thermal healing.

  18. Impedance monitoring at tendon-anchorage via mountable PZT interface and temperature-effect compensation

    Science.gov (United States)

    Huynh, Thanh-Canh; Nguyen, Tuan-Cuong; Choi, Sang-Hoon; Kim, Jeong-Tae

    2016-04-01

    In this study, the pre-stress force in pre-stressed concrete (PSC) girders is monitored via mountable PZT interface under varying temperature. Firstly, an impedance-based technique using mountable PZT interface is proposed for pre-stress-loss monitoring in tendon-anchorage systems. A cross correlation-based temperature-effect compensation algorithm using an effective frequency shift (EFS) of impedance signatures is visited. Secondly, lab-scale experiments are performed on a PSC girder instrumented with a mountable PZT interface at tendon-anchorage. A series of temperature variation and pre-stress-loss events are simulated for the lab-scale PSC girder. Thirdly, the feasibility of the mountable PZT interface for pre-stress-loss monitoring in tendon-anchorage is experimentally verified under constant temperature conditions. Finally, the PZT interface device is examined for pre-stress-loss monitoring under temperature changes to validate its applicability. The temperature effect on impedance signatures is compensated by minimizing cross-correlation deviation between impedance patterns of the mountable PZT interface.

  19. EFFECT OF SOL CONCENTRATION AND SUBSTRATE TYPE ON MICROSTRUCTURE FORMATION OF PZT THIN FILMS

    Directory of Open Access Journals (Sweden)

    ĽUBOMÍR MEDVECKÝ

    2011-03-01

    Full Text Available Pb(Zr0.52Ti0.48O3 (PZT sols were prepared by a modified sol-gel route using both solvents - acetic acid and stabilizer solution (n-propanol : 1,2-propanediol in the rate 10 : 1. The sols were deposited by spin-coating onto platinized Al2O3 or SiO2/Si substrates. Results of SEM and XRD analyses confirmed, that the transformation of the amorphous PZT film to perovskite structure happened after sintering at 650°C. The mechanism of microstructure formation has described for morphologicaly different perovskite particle types in 1, 2 and 3-layered PZT thin films with thickness of 200-500 nm on used substrates. Three different PZT film microstructure types in dependence on the applied sol concentration were found. It was found, that the PZT/Pt/Al2O3 film microstructure at 1.0 M sol concentration was composed of two forms of perovskite particles, big rosette and irregular cuboidal particles. Small spherical particles and rosette structure were found in PZT/Pt/Si/SiO2 films.

  20. Health monitoring of a continuous rigid frame bridge based on PZT impedance and strain measurements

    Science.gov (United States)

    Zhang, Junbing; Zhu, Hongping; Wang, Dansheng; He, Bo; Zhou, Huaqiang

    2009-07-01

    Critical civil infrastructures such as bridges, dams, and pipelines present a major investment and their safety and security affect the life of citizens and national economic development. So it is very important for engineers and researchers to monitor their integrity while in operation and throughout. In recent years, the piezoelectric-ceramic (PZT) patches, which serve both as impedance sensors and actuators, have been increasingly used for structural health monitoring. This paper presents an impedance-based method, which utilizes the electro-mechanical coupling property of PZT sensors. There are a lot of advantages of this method, such as not based on any physical models, sensitive to tiny damage for its high frequency characteristics. An engineering application of this method for health monitoring of a continuous rigid frame bridge is implemented in this study. Some PZT active sensors are embedded into critical sections of the continuous rigid-frame box beam. The electrical admittances of these distributed PZT sensors are measured when the bridge is constructing or suffering from operational loads. For comparison, strain gauges are arranged in adjacent regions of these PZT sensors to obtain the strains of concrete around them at the same time. Based on the admittance sigatures obtained form PZT sensors and the strain measurements of concrete around them, the health status of the bridge is monitored and evaluated successfully.

  1. Synthesis and dielectric properties of ferroelectric-ferrimagnetic PZT-SFMO composites

    Directory of Open Access Journals (Sweden)

    Alexander V. Petrov

    2017-03-01

    Full Text Available Ferrimagnetic-ferroelectric composite materials on the base of Pb0.85Zr0.53Ti0.47O3– Sr2FeMoO6–δ (PZT-SFMO compounds have been prepared by a complex ceramic technology and a modified sol-gel synthesis. The dielectric properties of the PZT-SFMO composites with the PZT concentrations of 55 wt% and less, as well as of pure SFMO, are caused by the Maxwell-Wagner relaxation and a huge electrical conductivity. In contrast, in pure PZT the ferroelectric phase transition is clearly expressed in the static dielectric permittivity anomaly. Moreover, in all investigated composites, similarly to pure SFMO, the electrical conductivity anomaly is observed in the range from 560–540 K. This indicates that the composites with PZT concentrations of 55 wt% and higher are above the electrical and magnetic percolation threshold, in a good agreement with the excluded volume theory. In PZT-SFMO composites the DC electrical conductivity increases with SFMO concentration almost in a power law fashion, while the activation energy of the DC conductivity decreases under certain conditions.

  2. Direct Intracochlear Acoustic Stimulation Using a PZT Microactuator

    Directory of Open Access Journals (Sweden)

    Chuan Luo

    2015-11-01

    Full Text Available Combined electric and acoustic stimulation has proven to be an effective strategy to improve hearing in some cochlear implant users. We describe an acoustic microactuator to directly deliver stimuli to the perilymph in the scala tympani. The 800 µm by 800 µm actuator has a silicon diaphragm driven by a piezoelectric thin film (e.g., lead-zirconium-titanium oxide or PZT. This device could also be used as a component of a bimodal acoustic-electric electrode array. In the current study, we established a guinea pig model to test the actuator for its ability to deliver auditory signals to the cochlea in vivo. The actuator was placed through the round window of the cochlea. Auditory brainstem response (ABR thresholds, peak latencies, and amplitude growth were calculated for an ear canal speaker versus the intracochlear actuator for tone burst stimuli at 4, 8, 16, and 24 kHz. An ABR was obtained after removal of the probe to assess loss of hearing related to the procedure. In some animals, the temporal bone was harvested for histologic analysis of cochlear damage. We show that the device is capable of stimulating ABRs in vivo with latencies and growth functions comparable to stimulation in the ear canal. Further experiments will be necessary to evaluate the efficiency and safety of this modality in long-term auditory stimulation and its ability to be integrated with conventional cochlear implant arrays.

  3. NMR quadruopole spectra of PZT from first-principles

    Science.gov (United States)

    Mao, Dandan; Walter, Eric J.; Krakauer, Henry

    2006-03-01

    High performance piezoelectric materials are disordered alloys, so it can be difficult to determine the local atomic geometry. Recently, high field NMR measurements have shown great promise as a microscopic probe of ABO3 perovskite-based alloys by their ability to resolve line-splittings due to nuclear quadrupolar coupling with the electric field gradient (EFG) at the nucleus. We report first-principles LDA calculations of the EFG's in monoclinic and tetragonal Pb(Zr0.5Ti0.5)O3 systems using the linear augmented planewave (LAPW) method, and we compute NMR static powder spectra for ^91Zr, ^47Ti, and ^17O atoms as a function of applied strain. With decreasing c/a ratio PZT converts from tetragonal to monoclinic symmetry. We observe that the calculated NMR spectra show dramatic deviations with decreasing c/a from that in tetragonal P4mm well before the electric polarization begins to rotate away from the [001] direction. This indicates that NMR measurements can be a very accurate probe of local structural changes in perovskite piezoelectrics. G. L. Hoatson, D. H. Zhou, F. Fayon, D. Massiot, and R. L. Vold, Phys. Rev. B, 66, 224103 (2002).

  4. Recent Progress on PZT Based Piezoelectric Energy Harvesting Technologies

    Directory of Open Access Journals (Sweden)

    Min-Gyu Kang

    2016-02-01

    Full Text Available Energy harvesting is the most effective way to respond to the energy shortage and to produce sustainable power sources from the surrounding environment. The energy harvesting technology enables scavenging electrical energy from wasted energy sources, which always exist everywhere, such as in heat, fluids, vibrations, etc. In particular, piezoelectric energy harvesting, which uses a direct energy conversion from vibrations and mechanical deformation to the electrical energy, is a promising technique to supply power sources in unattended electronic devices, wireless sensor nodes, micro-electronic devices, etc., since it has higher energy conversion efficiency and a simple structure. Up to now, various technologies, such as advanced materials, micro- and macro-mechanics, and electric circuit design, have been investigated and emerged to improve performance and conversion efficiency of the piezoelectric energy harvesters. In this paper, we focus on recent progress of piezoelectric energy harvesting technologies based on PbZrxTi1-xO3 (PZT materials, which have the most outstanding piezoelectric properties. The advanced piezoelectric energy harvesting technologies included materials, fabrications, unique designs, and properties are introduced to understand current technical levels and suggest the future directions of piezoelectric energy harvesting.

  5. Measurement and calculation of PZT thin film longitudinal piezoelectric coefficients.

    Energy Technology Data Exchange (ETDEWEB)

    Christman, J. A.; Kim, S.-H.; Kingon, A. I.; Maiwa, H.; Maria, J.-P.; Streiffer, S. K.

    1999-04-26

    The ferroelectric and piezoelectric properties of 2000 {angstrom} thick chemical solution deposited Pb(Zr{sub x}Ti{sub 1{minus}x})O{sub 3} (PZT) thin films were investigated. Several Zr/Ti ratios were studied: 30/70, 50/50 and 65/35, which correspond to tetragonal, near-morphotropic, and rhombohedral symmetries. In all samples, a {l_brace}111{r_brace}-texture is predominant. Longitudinal piezoelectric coefficients and their dc field dependence were measured using the contact AFM method. The expected trend of a maximum piezoelectric coefficient at or near to the MPB was not observed. The composition dependence was small, with the maximum d{sub 33} occurring in the tetragonal material. To explain the results, crystallographic texture and film thickness effects are suggested. Using a modified phenomenological approach, derived electrostrictive coefficients, and experimental data, d{sub 33} values were calculated. Qualitative agreement was observed between the measured and calculated coefficients. Justifications of modifications to the calculations are discussed.

  6. PZT Network and Phased Array Lamb Wave Based SHM Systems

    Energy Technology Data Exchange (ETDEWEB)

    Silva, C [Academia da Forca Aerea, Granja do Marques, 2715-021 Pero Pinheiro (Portugal); Rocha, B; Suleman, A, E-mail: cbsilva@emfa.pt [University of Victoria, Department of Mechanical Engineering, PO Box 3055, Stn.CSC, Victoria, BC, V8W 3P6 (Canada)

    2011-07-19

    With the application of newer materials, such as composite materials, and growing complexity and capacity of current aircraft structures, reliably and completely assess the condition of the total structures in real time is then of growing and utmost importance. PZT Network and Phased Array, Lamb wave based Structural Health Monitoring (SHM) systems were developed to be applied to thin panels. The selection of transducers, their size and selected locations for their installation are described. The development and selection of the signal generation and data acquisition systems is also presented in detail. The requirements conducing to the development and selection of these systems are laid and particularly the selection of the actuation signal applied is justified. The development of a damage detection algorithm based in the comparison of the current structural state to a reference state is described, to detect damage reflected Lamb waves. Such method was implemented in software and integrated in the SHM system developed. Subsequently the detection algorithm, based in discrete signals correlation, was further improved by incorporating statistical methods. For phased arrays, a novel damage location algorithm is presented based on the individual sensors response. A visualization method based concurrently in the statistical methods developed and superposition of the different results obtained from a test set was implemented. These tests conducted to the successful and repeatable detection of 1mm damages in a multiple damaged plate with great confidence. Finally, a brief comparison and a hybrid system implementation is presented.

  7. Giant magnetoelectric effects in ferrite - PZT multilayer composites

    Science.gov (United States)

    Srinivasan, G.; Rasmussen, E. T.

    2002-03-01

    Materials that respond to both electric and magnetic fields are said to be magnetoelectric (ME) and facilitate field conversion. One way in principle to accomplish strong ME effects is a composite of magnetostrictive and piezoelectric materials in which the coupling is mediated by mechanical deformation. This report is on the synthesis of novel multilayers of magnetostrictive nickel zinc ferrite (NZFO) and piezoelectric lead zirconate titanate (PZT) that show a giant ME effect and maximum field conversion efficiency [1]. Bilayers and multilayers were prepared from thick films obtained by tape casting. The ME voltage coefficient was measured as a function of sample and experimental parameters. The coefficient ranged from 30 to 1500 mV/cm Oe, depending on the sample composition, volume fraction, and field orientation. The transverse coupling is an order of magnitude stronger than the longitudinal coefficient. The ME coefficient is maximum at room temperature and increases with increasing frequency. Data on the dependence of ME coupling on volume fraction of the two phases and bias magnetic field are in excellent agreement with theoretical predictions. - work supported by a grant from the NSF (DMR-0072144) 1. G. Srinivasan, E. T. Rasmussen, J. Gallegos, R. Srinivasan, Yu. I. Bokhan, and V. M. Laletin, Phys. Rev. B 64, 214408 (2001).

  8. Energy Harvesting Using Screen Printed PZT on Silicon

    DEFF Research Database (Denmark)

    Lei, Anders

    as a result. Cleanroom contamination issues in the cantilever etching due to the PZT film is solved with a KOH etch where the wafer front side is protected mechanically. From thorough characterisation of the fabricated harvester, it is validated that the power output can be expressed as a power available term...... and a multiplication factor equal to or less than 1. The available power is proportional to the force acting on the cantilever squared and the inverse of the viscous damping coefficient. The latest fabricated batch of harvesters produced in average 34.5 µW of RMS power over a resistive load of 50 k? with an RMS...... acceleration of 0.5g at 511 Hz. The best performing devices under similar conditions produced 44.9 µW at 543 Hz. Compared to other state of the art miniaturised vibration energy harvesters, the normalised power density for the harvesters fabricated in this work is 3.5 times higher than the next best harvester....

  9. Fabrication of sub-micro size PZT array and their ferroelectric properties

    Institute of Scientific and Technical Information of China (English)

    ZHAO Gaoyang; ZHANG Weihua; XU Guomin; DENG Xiaocui; JIANG Bailing; ZHAO Wei

    2006-01-01

    The photosensitive PZT sols and their gel films were prepared by sol-gel process. Based on the photosensitivity of the PZT gel films, two-dimensional (2D) array of the PZT gel film was fabricated using twice-exposure of double-beam interference on the gel film. PZT gel films coated on ITO/quartz substrate were exposed to an interference fringe of 325 He-Cd laser beams, the substrate was rotated by 90° between the first and second irradiation steps. Island type periodic 2D array structures with a pitch of 1 μm and cell size of about 480 nm × 480 nm × 40 nm were formed after the irradiation, and followed by leaching with organic solvent, and then by heat treatment at 600℃ for 15 min. The hysteresis loops of the cell in PZT array were in-situ measured by the online-operation of TF analyzer and atomic force microscope (AFM). The probe can be located on the locked cell of PZT array in the AFM image. The alternating voltage applied to the locked cell is supplied by the TF analyzer through the conductive coating probe, and then the test signal is fed back to the TF analyzer to obtain the hysteresis loop of the locked cell of array in the absence of top electrode. The results show that the sub-micro size PZT arrays prepared in this way are of polarization reversal characteristics with the alternating electric fields, thereby exhibiting obvious ferroelectricity.

  10. Photoluminescence properties of PZT 52/48 synthesized by microwave hydrothermal method using PVA with template

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, G.F., E-mail: guilmina@hotmail.com [Instituto de Quimica, Universidade Estadual Paulista, Departamento de Bioquimica e Tecnologia Quimica, Rua Francisco Degni s/n, Quitandinha, 14800-900 Araraquara, SP (Brazil); Gasparotto, G. [Instituto de Quimica, Universidade Estadual Paulista, Departamento de Bioquimica e Tecnologia Quimica, Rua Francisco Degni s/n, Quitandinha, 14800-900 Araraquara, SP (Brazil); Paris, E.C. [Empresa Brasileira de Pesquisa Agropecuaria, Embrapa Instrumentacao, Rua XV de novembro, 1452, Centro, 13.569-970 Sao Carlos, SP (Brazil); Zaghete, M.A.; Longo, E.; Varela, J.A. [Instituto de Quimica, Universidade Estadual Paulista, Departamento de Bioquimica e Tecnologia Quimica, Rua Francisco Degni s/n, Quitandinha, 14800-900 Araraquara, SP (Brazil)

    2012-01-15

    Lead Titanate Zirconate (PZT) perovskite powders were synthesized by microwave hydrothermal method (M-H) at 180 {sup o}C for different time periods (2, 4, 8 and 12 h) with the presence of aqueous polyvinyl alcohol (PVA) solution 0.36 g L{sup -1}. The X-Ray diffraction (XRD), SE-FEG as well as the measurements of photoluminescence (PL) emission were used for monitoring the formation of a perovskite phase with random polycrystalline distortion in the structure. Emission spectra with fixed excitation wavelength of 350 nm showed higher value for the powder obtained after undergoing 8 h of treatment. A theoretical model derived from previous calculations allows us to discuss the origin of photoluminescence emission in the powders, which can be further related to the local disorder in the network of both ZrO{sub 6} and TiO{sub 6} octahedral, and dodecahedral PbO{sub 12}. The new morphology initially observed from the PZT perovskite crystal growth bearing the shape of fine plates is found to be directly related to photoluminescence emission with energy lower than that present in the PZT with cube-like morphology that emits in 560 nm. - Highlights: > This work details the efficiency of microwave hydrothermal synthesis in obtaining PZT powders. > PVA is used as a crystallization agent of PZT particles. > PZT particles presented photoluminescent (PL) behavior. > There aren't previous reports of photoluminescent PZT obtained by microwave hydrothermal synthesis. > Photoluminescence is one more interesting property for technological applications this material.

  11. Development of valve-less tube-type micropump with PZT actuator

    Science.gov (United States)

    Tsuchiya, Kazuyoshi; Morishima, Akifumi; Takamata, Atsushi; Uetsuji, Yasutomo; Nakamachi, Eiji

    2008-12-01

    The medical devices such as a micropump to extract blood through a tube have a structure which needle and pump part are mutually separated. Therefore, it is not easy to make smaller than the conventional pump. In this research, we aim to develop the pump combined with a tube as a final purpose. In this study, ring type PZT elements are mounted on the surface of the silicone tube, and the stationary waves are generated in the tube by the vibration of those PZT on the tube verified by changing the AC voltage. The waves generated by the collision of large and small stationary waves are synthesized, and then the wave becomes a progressive wave with an elliptic motion in the tube. The flow function demonstrated by the tube type micropump was evaluated and the flow velocities were increased 2.78% and decreased 1.79%. On the other hand, we have a technique to produce a titanium microtube by using RF magnetron sputtering deposition technique. A Titanium micro tube with the size of a female mosquito's labium (60µm external and 25μm internal diameter) was produced by the sputter deposition method. In order to deposit PZT thin film on the titanium micro tube, the thin film process is used. The thin film deposition conditions of the PZT thin film are investigated and the characteristic of the PZT thin films are evaluated.

  12. TECHNICAL NOTE: The development of a PZT-based microdrive for neural signal recording

    Science.gov (United States)

    Park, Sangkyu; Yoon, Euisung; Lee, Sukchan; Shin, Hee-sup; Park, Hyunjun; Kim, Byungkyu; Kim, Daesoo; Park, Jongoh; Park, Sukho

    2008-04-01

    A hand-controlled microdrive has been used to obtain neural signals from rodents such as rats and mice. However, it places severe physical stress on the rodents during its manipulation, and this stress leads to alertness in the mice and low efficiency in obtaining neural signals from the mice. To overcome this issue, we developed a novel microdrive, which allows one to adjust the electrodes by a piezoelectric device (PZT) with high precision. Its mass is light enough to install on the mouse's head. The proposed microdrive has three H-type PZT actuators and their guiding structure. The operation principle of the microdrive is based on the well known inchworm mechanism. When the three PZT actuators are synchronized, linear motion of the electrode is produced along the guiding structure. The electrodes used for the recording of the neural signals from neuron cells were fixed at one of the PZT actuators. Our proposed microdrive has an accuracy of about 400 nm and a long stroke of about 5 mm. In response to formalin-induced pain, single unit activities are robustly measured at the thalamus with electrodes whose vertical depth is adjusted by the microdrive under urethane anesthesia. In addition, the microdrive was efficient in detecting neural signals from mice that were moving freely. Thus, the present study suggests that the PZT-based microdrive could be an alternative for the efficient detection of neural signals from mice during behavioral states without any stress to the mice.

  13. Optimization of composition and crystal structure for processing route of PZT system

    Energy Technology Data Exchange (ETDEWEB)

    Kakimoto, K.; Kakemoto, H.; Fujita, S.; Masuda, Y. [Hachinohe Inst. of Tech., Aomori (Japan). JSPS Research Project

    2002-07-01

    An evaluation procedure that employs by calibrated X-ray fluorescence (XRF) analysis of the chemical composition of PZT bulk ceramics and thin films deposited on Si-based substrate by the pulsed laser deposition (PLD) technique has been established. The plots of cation fraction and XRF intensity for Pb, Zr and Ti atoms were curve-fitted using the results obtained by XRF measurement of normalized PZT samples whose compositions were selected from those near the morphotropic phase boundary (MPB) of PZT(Zr/Ti=53/47). While the Pb curve was almost linear, Zr and Ti yielded parabolic curves due to the effect of matrix Pb. In the case of thin-film analysis, the substrate beneath the thin film exerted a matrix effect on the quantitative analysis of the thin film. Both the coexisting element effect and the substrate effect were calibrated to prepare an excellent XRF table for the precise quantitative analysis of PZT thin films. The present XRF table quantitatively revealed a variation in PZT composition during the high-temperature sintering process of bulk and even its thin-film prepared by PLD. The combination of X-ray diffraction (XRD) with model calculation also supported quantitative XRF analysis of the compositional difference from Pb stoichiometry. (orig.)

  14. PMN-PT-PZT composite films for high frequency ultrasonic transducer applications.

    Science.gov (United States)

    Hsu, Hsiu-Sheng; Benjauthrit, Vatcharee; Zheng, Fan; Chen, Rumin; Huang, Yuhong; Zhou, Qifa; Shung, K Kirk

    2012-06-01

    We have successfully fabricated x(0.65PMN-0.35PT)-(1 - x)PZT (xPMN-PT-(1 - x)PZT), where x is 0.1, 0.3, 0.5, 0.7 and 0.9, thick films with a thickness of approximately 9 µm on platinized silicon substrate by employing a composite sol-gel technique. X-ray diffraction analysis and scanning electron microscopy revealed that these films are dense and creak-free with well-crystallized perovskite phase in the whole composition range. The dielectric constant can be controllably adjusted by using different compositions. Higher PZT content of xPMN-PT-(1 - x)PZT films show better ferroelectric properties. A representative 0.9PMN-PT-0.1PZT thick film transducer is built. It has 200 MHz center frequency with a -6 dB bandwidth of 38% (76 MHz). The measured two-way insertion loss is 65 dB.

  15. Study of 1-3 PZT fibre/epoxy composite force sensor

    Science.gov (United States)

    Choy, S. H.; Chan, H. L. W.; Ng, M. W.; Liu, P. C. K.

    2005-09-01

    Lead zirconate titanate (PZT) fibres were prepared by a powder-based extrusion method. Pre-sintered PZT powder mixed with poly(acrylic acid) was spun in a spinnerette to produce fibres. The fibre of ˜400 μm diameter was used to fabricate 1-3 PZT fibre/epoxy composite discs with different volume fractions (ϕ) of PZT. Since the ceramic fibres are rather brittle, their elastic properties cannot be measured directly. In order to determine the properties of the ceramic fibres, effective properties of the fibres/epoxy 1-3 composite were measured. By using a modified series and parallel model, the properties of 1-3 composites can be calculated. Then, the elastic coefficient s33,fibreE, relative permittivity ɛ33,fibreT and piezoelectric strain coefficient d33,fibre of the ceramic fibre could be found. Ring-shaped PZT fibre/epoxy materials composites with different ϕ were fabricated to be used as the sensing material in force sensor applications. The ring-shape composite with ϕ=0.5 was installed into a housing and the sensor was calibrated by different methods and its sensitivity was found to be 144 pC/N within the frequency range of 0.5 6.4 kHz which is much higher than that of a quartz force sensor with a similar structure.

  16. Design and Experiment of PZT Network-based Structural Health Monitoring Scanning System

    Institute of Scientific and Technical Information of China (English)

    Qiu Lei; Yuan Shenfang; Wang Qiang; Sun Yajie; Yang Weiwei

    2009-01-01

    The active Lamb wave and piezoelectric transducer (PZT)-based structural health monitoring (SHM) technology is a kind of efficient approach to estimate the health state of aircraft structure. In practical applications, PZT networks are needed to monitor large scale structures. Scanning many of the different PZT actuator-sensor channels within these PZT networks to achieve on-line SHM task is important. Based on a peripheral component interconnect extensions for instrumentation (PXI) platform, an active Lamb wave and PZT network-based integrated multi-channel scanning system (PXI-ISS) is developed for the purpose of practical applications of SHM, which is compact and portable, and can scan large numbers of actuator-sensor channels and perform damage assessing automatically. A PXI-based 4 channels gain-programmable charge amplifier, an external scanning module with 276 actuator-sensor channels and integrated SHM software are proposed and discussed in detail. The experimental research on a carbon fiber composite wing box of an unmanned aerial vehicle (UAV) for verifying the functions of the PXI-ISS is mainly discussed, including the design of PZTs layer, the method of excitation frequency selection, functional test of damage imaging, stability test of the PXI-ISS, and the loading effect on signals. The experimental results have verified the stability and damage functions of this system.

  17. Large electric-field control of perpendicular magnetic anisotropy in strained [Co/Ni] / PZT heterostructures

    Science.gov (United States)

    Gopman, Daniel; Dennis, Cindi; Chen, P. J.; Iunin, Yury; Shull, Robert

    We present a piezoelectric/ferromagnetic heterostructure with PMA - a Co/Ni multilayer sputtered directly onto a Pb(Zr,Ti)O3 (PZT) substrate. Chemical-mechanical polishing was used to reduce the roughness of PZT plates to below 2 nm rms, enabling optimal magnetoelectric coupling via the direct interface between PZT and sputtered Co/Ni films with large PMA (Keff = (95 +/-9 kJ/m3)) . We grew the following layer stack: Ta(3)/Pt(2)/[Co(0.15)/Ni(0.6)]x4/Co(0.15)/Pt(2)/Ta(3); numbers in parentheses indicate thicknesses in nm. Applied electric fields up to +/- 2 MV/m to the PZT generated 0.05% in-plane compression in the Co/Ni multilayer, enabling a large electric-field reduction of the PMA (ΔKeff >= 103 J/m3) and of the coercive field (35%). Our results demonstrate that: (i) heterostructures combining PZT and [Co/Ni] exhibit larger PMA (Keff ~105 J/m3) than previous magnetoelectric heterostructures based on Co/Pt and CoFeB, enabling thermally stable hybrid magnetoelectric/spintronic devices only tens of nm in diameter and (ii) electric-field control of the PMA is promising for more energy efficient switching of spintronic devices.

  18. Development of PZT-excited stroboscopic shearography for full-field nondestructive evaluation

    Science.gov (United States)

    Asemani, Hamidreza; Park, Jinwoo; Lee, Jung-Ryul; Soltani, Nasser

    2017-05-01

    Nondestructive evaluation using shearography requires a way to stress the inspection target. This technique is able to directly measure the displacement gradient distribution on the object surface. Shearography visualizes the internal structural damages as the anomalous pattern in the shearograpic fringe pattern. A piezoelectric (PZT) excitation system is able to generate loadings in the vibrational, acoustic, and ultrasonic regimes. In this paper, we propose a PZT-excited stroboscopic shearography. The PZT excitation could generate vibrational loading, a stationary wavefield, and a nonstationary propagation wave to fulfill the external loading requirement of shearography. The sweeping of the PZT excitation frequency, the formation of a standing wave, and a small shearing to suppress the incident wave were powerful controllable tools to detect the defects. The sweeping of the PZT excitation frequency enabled us to determine one of the defect-sensitive frequencies almost in real time. In addition, because the defect sensitive frequencies always existed in wide and plural ranges, the risk of the defect being overlooked by the inspector could be alleviated. The results of evaluation using stroboscopic shearography showed that an artificial 20 mm-diameter defect could be visualized at the excitation frequencies of 5-8 kHz range and 12.5-15.5 kHz range. This technique provided full field reliable and repeatable inspection results. Additionally, the proposed method overcame the important drawback of the time-averaged shearography, being required to identify the resonance vibration frequency sensitive to the defect.

  19. In situ X-ray diffraction studies on the piezoelectric response of PZT thin films

    Energy Technology Data Exchange (ETDEWEB)

    Davydok, A., E-mail: davydok@mpie.de [Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 13397 Marseille (France); Max-Planck-Institut für Eisenforschung, Department Structure and Nano-/Micromechanics of Materials, D-40237 Düsseldorf (Germany); Cornelius, T.W. [Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 13397 Marseille (France); Mocuta, C. [SOLEIL Synchrotron, DiffAbs beamline, L' Orme des Merisiers, Saint-Aubin - BP 48, 91192 Gif-sur-Yvette Cedex (France); Lima, E.C. [Universidade Federal do Tocantins, 77500-000 Porto Nacional, TO (Brazil); Araujo, E.B. [Departamento de Fisica e Quimica, Universidade Estadual Paulista, Av. Brasil, 56 Centro, 15385-000 Ilha Solteira, SP (Brazil); Thomas, O. [Aix Marseille Université, CNRS, Université de Toulon, IM2NP UMR 7334, 13397 Marseille (France)

    2016-03-31

    Piezoelectric properties of randomly oriented self-polarized PbZr{sub 0.50}Ti{sub 0.50}O{sub 3} (PZT) thin films were investigated using in situ synchrotron X-ray diffraction. Possibilities for investigating the piezoelectric effect using micro-sized hard X-ray beams are demonstrated and perspectives for future dynamical measurements on PZT samples with variety of compositions and thicknesses are given. Studies performed on the crystalline [100, 110] directions evidenced piezoelectric anisotropy. The piezoelectric coefficient d{sub 33} was calculated in terms of the lab reference frame (d{sub perp}) and found to be two times larger along the [100] direction than along the [110] direction. The absolute values for the d{sub perp} amount to 120 and 230 pm/V being in good agreement with experimental and theoretical values found in literature for bulk PZT ceramics. - Highlights: • We performed in situ synchrotron X-ray diffraction studies on (PZT) thin films. • We discuss anisotropy of piezo effect in different crystallographic directions. • Perpendicular component Piezo coefficient of thin PZT layer is defined.

  20. Influence of the stress on magnetoelectric effect in magnetostrictive-PZT bilayers

    Institute of Scientific and Technical Information of China (English)

    DING Jian-ming; ZHONG Chong-gui; JIANG Qing

    2007-01-01

    In this letter,we investigate the influence of the stress on magnetoelectric(ME)effect in a magnetostrictivePZT bilayer.ME voltage coefficient α*E=δE/δH,where δE is the induced electric field for an applied alternating current (ac)magnetic field δH,is obtained by solving the stressrelated piezoelectric constitutive equation and the conventional magnetostrictive equation with appropriate boundary condition.Based on the free-energy density function of the PZT film in stress state,we get the stress-related piezoelectric charge coefficient Pd*31 and dielectric permittivity Pε*33.After taking the cobalt ferrite(CFO)as magnetostrictive phase,it is found that α*E increases with decreasing 2-d compressive stress for CFO-PZT,which not only is qualitatively consistent with previous experimental measurements,but also provides a possible route to improve the ME effect.

  1. Temperature Field Analysis for PZT Pyroelectric Cells for Thermal Energy Harvesting

    Directory of Open Access Journals (Sweden)

    Chi-Yuan Lee

    2011-11-01

    Full Text Available This paper proposes the idea of etching PZT to improve the temperature variation rate of a thicker PZT sheet in order to enhance the energy conversion efficiency when used as pyroelectric cells. A partially covered electrode was proven to display a higher output response than a fully covered electrode did. A mesh top electrode monitored the temperature variation rate and the electrode area. The mesh electrode width affected the distribution of the temperature variation rate in a thinner pyroelectric material. However, a pyroelectric cell with a thicker pyroelectric material was beneficial in generating electricity pyroelectrically. The PZT sheet was further etched to produce deeper cavities and a smaller electrode width to induce lateral temperature gradients on the sidewalls of cavities under homogeneous heat irradiation, enhancing the temperature variation rate.

  2. THE MONOCLINIC PHASE IN PZT: NEW LIGHT ON MORPHOTROPIC PHASE BOUNDARIES

    Energy Technology Data Exchange (ETDEWEB)

    NOHEDA,B.; GONZALO,J.A.; GUO,R.; PARK,S.E.; CROSS,L.E.; COX,D.E.; SHIRANE,G.

    2000-03-09

    A summary of the work recently carried out on the morphotropic phase boundary (MPB) of PZT is presented. By means of x-ray powder diffraction on ceramic samples of excellent quality, the MPB has been successfully characterized by changing temperature in a series of closely spaced compositions. As a result, an unexpected monoclinic phase has been found to exist in between the well-known tetragonal and rhombohedral PZT phases. A detailed structural analysis, together with the investigation of the field effect in this region of compositions, have led to an important advance in understanding the mechanisms responsible for the physical properties of PZT as well as other piezoelectric materials with similar morphotropic phase boundaries.

  3. Liquid Density Sensing Using Resonant Flexural Plate Wave Device with Sol-Gel PZT Thin Films

    CERN Document Server

    Yu, Jyh-Cheng

    2008-01-01

    This paper presents the design, fabrication and preliminary experimental results of a flexure plate wave (FPW) resonator using sol-gel derived lead zirconate titanates (PZT) thin films. The resonator adopts a two-port structure with reflecting grates on the composite membrane of PZT and SiNx. The design of the reflecting grate is derived from a SAW resonator model using COM theory to produce a sharp resonant peak. The comparison between the mass and the viscosity effects from the theoretical expression illustrates the applications and the constraints of the proposed device in liquid sensing. Multiple coatings of sol-gel derived PZT films are adopted because of the cost advantage and the high electromechanical coupling effect over other piezoelectric films. The fabrication issues of the proposed material structure are addressed. Theoretical estimations of the mass and the viscosity effects are compared with the experimental results. The resonant frequency has a good linear correlation with the density of low v...

  4. Wireless Impedance Sensor with PZT-Interface for Prestress-Loss Monitoring in Prestressed Concrete Girder

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Khac Duy; Lee, So Young; Kim, Jeong Tae [Pukyong National University, Busan (Korea, Republic of)

    2011-12-15

    Ensuring the designed prestress force is very important for the safety of prestressed concrete bridge. The loss of prestress force in tendon could significantly reduce load carrying capacity of the structure. In this study, an automated prestress-loss monitoring system for prestressed concrete girder using PZT-interface and wireless impedance sensor node is presented. The following approaches are carried out to achieve the objective. Firstly, wireless impedance sensor nodes are designed for automated impedance-based monitoring technique. The sensor node is mounted on the high-performance Imote2 sensor platform to fulfill high operating speed, low power requirement and large storage memory. Secondly, a smart PZT-interface designed for monitoring prestress force is described. A linear regression model is established to predict prestress-loss. Finally, a system of the PZT-interface interacted with the wireless sensor node is evaluated from a lab-scale tendon-anchorage connection of a prestressed concrete girder.

  5. A PZT Actuated Triple-Finger Gripper for Multi-Target Micromanipulation

    Directory of Open Access Journals (Sweden)

    Tao Chen

    2017-01-01

    Full Text Available This paper presents a triple-finger gripper driven by a piezoceramic (PZT transducer for multi-target micromanipulation. The gripper consists of three fingers assembled on adjustable pedestals with flexible hinges for a large adjustable range. Each finger has a PZT actuator, an amplifying structure, and a changeable end effector. The moving trajectories of single and double fingers were calculated and finite element analyses were performed to verify the reliability of the structures. In the gripping experiment, various end effectors of the fingers such as tungsten probes and fibers were tested, and different micro-objects such as glass hollow spheres and iron spheres with diameters ranging from 10 to 800 μm were picked and released. The output resolution is 145 nm/V, and the driven displacement range of the gripper is 43.4 μm. The PZT actuated triple-finger gripper has superior adaptability, high efficiency, and a low cost.

  6. A Flexible Ultrasound Transducer Array with Micro-Machined Bulk PZT

    Directory of Open Access Journals (Sweden)

    Zhe Wang

    2015-01-01

    Full Text Available This paper proposes a novel flexible piezoelectric micro-machined ultrasound transducer, which is based on PZT and a polyimide substrate. The transducer is made on the polyimide substrate and packaged with medical polydimethylsiloxane. Instead of etching the PZT ceramic, this paper proposes a method of putting diced PZT blocks into holes on the polyimide which are pre-etched. The device works in d31 mode and the electromechanical coupling factor is 22.25%. Its flexibility, good conformal contacting with skin surfaces and proper resonant frequency make the device suitable for heart imaging. The flexible packaging ultrasound transducer also has a good waterproof performance after hundreds of ultrasonic electric tests in water. It is a promising ultrasound transducer and will be an effective supplementary ultrasound imaging method in the practical applications.

  7. Multiscale numerical study on ferroelectric nonlinear response of PZT thin films (Conference Presentation)

    Science.gov (United States)

    Wakabayashi, Hiroki; Uetsuji, Yasutomo; Tsuchiya, Kazuyoshi

    2017-06-01

    PZT thin films have excellent performance in deformation precision and response speed, so it is used widely for actuators and sensors of Micro Electro Mechanical System (MEMS). Although PZT thin films outputs large piezoelectricity at morphotropic phase bounfary (MPB), it shows a complicated hysteresis behavior caused by domain switching and structural phase transition between tetragonal and rhombohedral. In general, PZT thin films have some characteristic crystal morphologies. Additionally mechanical strains occur by lattice mismatch with substrate. Therefore it is important for fabrication and performance improvement of PZT thin films to understand the relation between macroscopic hysteresis response and microstructural changes. In this study, a multiscale nonlinear finite element simulation was proposed for PZT thin films at morphotropic phase boundary (MPB) on the substrate. The homogenization theory was employed for scale-bridging between macrostructure and microstructure. Figure 1 shows the proposed multiscale nonlinear simulation [1-3] based on the homogenization theory. Macrostructure is a homogeneous structure to catch the whole behaviors of actuators and sensors. And microstructure is a periodic inhomogeneous structure consisting of domains and grains. Macrostructure and microstructure are connected perfectly by homogenization theory and are analyzed by finite element method. We utilized an incremental form of fundamental constitutive law in consideration with physical property change caused by domain switching and structural phase transition. The developed multiscale finite element method was applied to PZT thin films with lattice mismatch strain on the substrate, and the relation between the macroscopic hysteresis response and microscopic domain switching and structural phase transition were investigated. Especially, we discuss about the effect of crystal morphologies and lattice mismatch strain on hysteresis response.

  8. Structure and electrical properties of PZT/LNO/PT multilayer films on stainless steel substrates

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    PbZr0.53Ti0.47O3 (PZT) ferroelectric thin films were deposited on LaNiO3 (LNO) by sol-gel method. The PbTiO3 (PT) seed layer was depos-ited between the LNO buffer layer and stainless steel (SS) substrate, which effectively decreased the annealing temperature of LNO layer from 750 C to 650 C. X-ray diffraction (XRD) reveals that LNO layers with PT layer crystallize into a perovskite phase on annealing at 650 C for 10 min. PZT deposited on LNO buffer layer with PT seed layer exhibits good ferroelectric proper...

  9. Ferroelectric–Ferromagnetic Composites Based on PZT Type Powder and Ferrite Powder

    OpenAIRE

    Bochenek D.; Niemiec P.; Zachariasz R.; Chrobak A.; Ziółkowski G.

    2013-01-01

    W pracy otrzymano ferroelektryczno-ferromagnetyczne kompozyty na bazie ceramicznego proszku typu PZT. Połączenie ferroelektrycznego i magnetycznego proszku miało na celu otrzymanie materiałów wykazujących zarówno elektryczne i magne- tyczne właściwości. Ferroelektryczny, ceramiczny proszek (w ilości 90%) stanowiły domieszkowane składy proszku typu PZT, natomiast magnetycznym składnikiem w kompozycie był niklówo-cynkowy ferryt (Nii-^Zn^Fe^Oj). Syntetyzowanie składni- ków kompozytu ceramiczno-f...

  10. Estimate of the changes in the characteristics of a PZT vibrator under a space environment

    Science.gov (United States)

    Kim, Jungsoon; Lee, Sanghoon; Kim, Moojoon

    2015-03-01

    To utilize lead zirconate titanate (PZT) vibrators in the aerospace industry, we formulate the changes in the characteristics of the vibrator for the transverse mode and the thickness mode as functions of the temperature. For practical use, we adopted a few linear functions and a square function as regression functions in order to estimate the characteristics of the commercialized PZT-5 series of ceramics. The input admittance characteristics were calculated using the characteristic functions suggested in this study, and the results showed good agreement with the measured ones.

  11. Optical properties of PZT thin films deposited on a ZnO buffer layer

    OpenAIRE

    Schneider, T.; Leduc, D; Cardin, J.; LUPI, C; Barreau, N; Gundel, H.

    2007-01-01

    International audience; The optical properties of lead zirconate titanate (PZT) thin films deposited on ZnO were studied by m-lines spectroscopy. In order to retrieve the refractive index and the thickness of both layers from the m-lines spectra, we develop a numerical algorithm for the case of a two-layer system and show its robustness in the presence of noise. The sensitivity of the algorithm of the two-layer model allows us to relate the observed changes in the PZT refractive index to the ...

  12. Piezoelectric Resonance Investigation of Zr-rich PZT at Room Temperature

    NARCIS (Netherlands)

    Cereceda, N.; Noheda, B.; Fernandez-del-Castillo, J.R.; Gonzalo, J.A.; Frutos, J. De

    1999-01-01

    We study the piezoelectric resonances in poled PZT ceramics by means of a microscopic model. It connects the microscopic vibrations of the ionic units, cooperatively producing the piezoelectric effect, with the macroscopic piezoelectric parameters. The behaviour at the resonance is well described in

  13. Investigation of Top/bottom Electrode and Diffusion Barrier Layer for PZT thick film MEMS Sensors

    DEFF Research Database (Denmark)

    Pedersen, Thomas; Hindrichsen, Christian Carstensen; Lou-Møller, R.

    2007-01-01

    In this work screen printed piezoelectric Ferroperm PZ26 lead zirconate titanate (PZT) thick film is used for two MEMS devices. A test structure is used to investigate several aspects regarding bottom and top electrodes. 450 nm ZrO2 thin film is found to be an insufficient diffusion barrier layer...

  14. Optimization of the low-temperature MOCVD process for PZT thin films

    CERN Document Server

    Wang, C H; Choi, D J

    2000-01-01

    Pb(Zr sub X Ti sub 1 sub - sub X)O sub 3 (PZT) thin films of about 0.34 nm were successfully grown at a low temperature of 500 .deg. C by metalorganic chemical vapor deposition with a beta-diketonate complex of Pb(tmhd) sub 2 , zirconium t-butoxide, and titanium isopropoxide as source precursors. Ferroelectric capacitors of a Pt/PZT/Pt configuration were fabricated, and their structural and electrical properties were investigated as a function of the input Pb/(Zr+Ti) and Zr/(Zr+Ti) source ratios. The structure of the as-grown films at 500 .deg. C changed from tetragonal to pseudocubic with increasing the Zr/(Zr+Ti) ratio above an input Pb/(Zr+Ti) source ratio of 5.0 while a 2nd phase of ZrO sub 2 was only observed below Pb/(Zr+Ti) ratio of 5.0, regardless of the Zr/(Zr+Ti) ratio. The dielectric constant and loss of the PZT films were 150-1200 and 0.01-0.04 at 100 kHz, respectively, Leakage current densities decreased with increasing the Zr/(Zr+Ti) ratio. The process window for growing a single phase PZT is ve...

  15. Exploring the piezoelectric performance of PZT particulate-epoxy composites loaded in shear

    NARCIS (Netherlands)

    Loock, F.V.; Deutz, D.B.; Zwaag, S.V.D.; Groen, W.A.

    2016-01-01

    The active and passive piezoelectric response of lead zirconium titanate (PZT)-epoxy particulate composites loaded in shear is studied using analytical models, a finite element model and by experiments. The response is compared to that of the same composites when loaded in simple tension. Analogousl

  16. In-situ structural investigations of ferroelasticity in soft and hard rhombohedral and tetragonal PZT

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, Maxim I., E-mail: maximm@alumni.ntnu.no; Einarsrud, Mari-Ann; Tolchard, Julian R.; Grande, Tor [Department of Materials Science and Engineering, Norwegian University of Science and Technology, NO-7491 Trondheim (Norway); Geiger, Philipp T.; Webber, Kyle G. [Department of Materials Science, Friedrich-Alexander-Universität Erlangen-Nürnberg, 91058 Erlangen (Germany); Damjanovic, Dragan [Ceramics Laboratory, Swiss Federal Institute of Technology in Lausanne-EPFL, 1015 Lausanne (Switzerland)

    2015-10-28

    Despite the technological importance of hard and soft PZT, Pb(Zr,Ti)O{sub 3}, ceramics, the mechanisms of ferroelectric hardening and softening remain widely discussed in the literature. The hardening and softening phenomena have traditionally been investigated in relation with dielectric manifestations such as aging of the dielectric susceptibility and constriction of the polarization-electric field hysteresis loop. Here, we present a systematic investigation of the ferroelectric and ferroelastic properties of soft and hard PZT in both the tetragonal and rhombohedral phases. A particular focus has been devoted to ferroelastic domain switching by characterizing the macroscopic mechanical constitutive behavior and in-situ synchrotron X-ray diffraction during compression. It is demonstrated that variation of the ordering state of point defects in PZT ceramics affects the switching behavior of both ferroelectric and ferroelastic domains under mechanical or electrical fields. Softening of the mechanical and electrical properties of originally hard PZT ceramics was conferred by quenching the materials from above the Curie temperature. The present findings are discussed with respect to the current understanding of hardening-softening transitions in ferroelectric materials.

  17. Parametric study on a collocated PZT beam vibration absorber and power harvester

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Shyh Chin [Mechanical Engineering, Ming Chi University of Technology, New Taipei (China); Tsai, Chao Yang [Mechanical Engineering Army Academy, R.O.C., Taoyuan (China); Liao, Hsiao Hui [LNG Construction and Project Division, CPC Corp., Taipei (China)

    2016-11-15

    The parametric effects of a PZT beam that is simultaneously used as a vibration absorber and a power harvester were investigated in this study. A cantilever beam paved with PZT layers and with added tip mass has been widely used as a harvester or sometimes as a Dynamic vibration absorber (DVA). However, the beam is rarely considered a collocated device. In this study, the first step was theoretical derivation of a distributed beam covered with bimorph PZT layers. Then, the beam was attached to a 1DOF vibratory main system. Two indicators for vibration absorption and power harvesting were defined. Numerical results demonstrated that the lumped mass ratio favored both of the abilities, but that the DVA mass ratio influenced these two abilities in exactly the opposite way. The conjunction of a harvester circuit into a DVA shifted its resonance frequency up to 5 % (an extreme case of open circuit R→∞). Simultaneous power harvesting diminished the absorption capability up to 35 % for each set of mass ratios. To achieve the maximum degree of power harvesting, a corresponding load resistance that somewhat increases with the lumped mass ratio is applied. Experimental results verified the existence of the best load resistance, but the measured harvested curve was lower than the theoretical calculation because of structure damping and deviations of PZT material properties.

  18. A rotary ultrasonic motor using radial bending mode of ring with nested PZT excitation

    Institute of Scientific and Technical Information of China (English)

    Ying-xiang LIU; Jun-kao LIU; Wei-shan CHEN; Xiao-hui YANG

    2012-01-01

    This study presents and verifies a new idea for constructing a rotary traveling wave ultrasonic motor (USM) that uses the radial bending mode of a ring.In the new design,20 trapezoid cross section slots are cut symmetrically in the outer surface of a thick duralumin alloy ring,where 20 PZT stacks are nested.In each slot,two wedging blocks are set between the PZT stack and the two sides of the slot respectively to apply preloading on the PZT ceramics.Two radial bending modes of the stator that have a phase difference of a quarter wavelength on space are generated by using the d33 operating mode of the PZT elements,and then a flexural traveling wave is formed by the superimposing of two standing waves whose amplitudes are equal and phases are different by 90° temporally.Two conical rotors are pressed to each end of the ring type stator by a coiled spring.The finite element method (FEM) simulation is developed to validate the feasibility of the proposed motor.The maximal speed and torque of the prototype are tested to be 126 r/min and 0.8 N·m,respectively.

  19. Ferroelectric and piezoelectric properties of epitaxial PZT films and devices on silicon

    NARCIS (Netherlands)

    Nguyen, Minh Duc

    2010-01-01

    In this thesis, the integration of lead zirconate titanate Pb(Zr,Ti)O3 (PZT) thin films into piezoelectric microelectromechanical systems (MEMS) based on silicon is studied. In these structures, all epitaxial oxide layers (thin film/electrode/buffer-layer(s)) were deposited by pulsed laser depositio

  20. Enhancement of ferroelectric and piezoelectric properties in PZT thin films with heterolayered structure

    NARCIS (Netherlands)

    Nguyen, D.M.; Nguyen, Chi T.Q.; Trinh, Thong Q.; Nguyen, Tai; Pham, Thao N.; Rijnders, A.J.H.M.; Vu, Hung N.

    2013-01-01

    This paper reports the latest experimental results of multilayered, heterolayered, and alternating heterolayered PZT thin films obtained by spin coating on Pt/Ti/SiO2/Si wafers using Zr-rich (P60) and Ti-rich (P40) solutions which were prepared by sol–gel route process. The ferroelectric and piezoel

  1. Ferroelectric and piezoelectric properties of epitaxial PZT films and devices on silicon

    NARCIS (Netherlands)

    Nguyen, Duc Minh

    2010-01-01

    In this thesis, the integration of lead zirconate titanate Pb(Zr,Ti)O3 (PZT) thin films into piezoelectric microelectromechanical systems (MEMS) based on silicon is studied. In these structures, all epitaxial oxide layers (thin film/electrode/buffer-layer(s)) were deposited by pulsed laser depositio

  2. An Unconventional Inchworm Actuator Based on PZT/ERFs Control Technology

    Science.gov (United States)

    Liu, Guojun; Zhang, Yanyan; Liu, Jianfang; Li, Jianqiao; Tang, Chunxiu; Wang, Tengfei; Yang, Xuhao

    2016-01-01

    An unconventional inchworm actuator for precision positioning based on piezoelectric (PZT) actuation and electrorheological fluids (ERFs) control technology is presented. The actuator consists of actuation unit (PZT stack pump), fluid control unit (ERFs valve), and execution unit (hydraulic actuator). In view of smaller deformation of PZT stack, a new structure is designed for actuation unit, which integrates the advantages of two modes (namely, diaphragm type and piston type) of the volume changing of pump chamber. In order to improve the static shear yield strength of ERFs, a composite ERFs valve is designed, which adopts the series-parallel plate compound structure. The prototype of the inchworm actuator has been designed and manufactured in the lab. Systematic test results indicate that the displacement resolution of the unconventional inchworm actuator reaches 0.038 μm, and the maximum driving force and velocity are 42 N, 14.8 mm/s, respectively. The optimal working frequency for the maximum driving velocity is 120 Hz. The complete research and development processes further confirm the feasibility of developing a new type of inchworm actuator with high performance based on PZT actuation and ERFs control technology, which provides a reference for the future development of a new type of actuator. PMID:27022234

  3. An Unconventional Inchworm Actuator Based on PZT/ERFs Control Technology.

    Science.gov (United States)

    Liu, Guojun; Zhang, Yanyan; Liu, Jianfang; Li, Jianqiao; Tang, Chunxiu; Wang, Tengfei; Yang, Xuhao

    2016-01-01

    An unconventional inchworm actuator for precision positioning based on piezoelectric (PZT) actuation and electrorheological fluids (ERFs) control technology is presented. The actuator consists of actuation unit (PZT stack pump), fluid control unit (ERFs valve), and execution unit (hydraulic actuator). In view of smaller deformation of PZT stack, a new structure is designed for actuation unit, which integrates the advantages of two modes (namely, diaphragm type and piston type) of the volume changing of pump chamber. In order to improve the static shear yield strength of ERFs, a composite ERFs valve is designed, which adopts the series-parallel plate compound structure. The prototype of the inchworm actuator has been designed and manufactured in the lab. Systematic test results indicate that the displacement resolution of the unconventional inchworm actuator reaches 0.038 μm, and the maximum driving force and velocity are 42 N, 14.8 mm/s, respectively. The optimal working frequency for the maximum driving velocity is 120 Hz. The complete research and development processes further confirm the feasibility of developing a new type of inchworm actuator with high performance based on PZT actuation and ERFs control technology, which provides a reference for the future development of a new type of actuator.

  4. An Unconventional Inchworm Actuator Based on PZT/ERFs Control Technology

    Directory of Open Access Journals (Sweden)

    Guojun Liu

    2016-01-01

    Full Text Available An unconventional inchworm actuator for precision positioning based on piezoelectric (PZT actuation and electrorheological fluids (ERFs control technology is presented. The actuator consists of actuation unit (PZT stack pump, fluid control unit (ERFs valve, and execution unit (hydraulic actuator. In view of smaller deformation of PZT stack, a new structure is designed for actuation unit, which integrates the advantages of two modes (namely, diaphragm type and piston type of the volume changing of pump chamber. In order to improve the static shear yield strength of ERFs, a composite ERFs valve is designed, which adopts the series-parallel plate compound structure. The prototype of the inchworm actuator has been designed and manufactured in the lab. Systematic test results indicate that the displacement resolution of the unconventional inchworm actuator reaches 0.038 μm, and the maximum driving force and velocity are 42 N, 14.8 mm/s, respectively. The optimal working frequency for the maximum driving velocity is 120 Hz. The complete research and development processes further confirm the feasibility of developing a new type of inchworm actuator with high performance based on PZT actuation and ERFs control technology, which provides a reference for the future development of a new type of actuator.

  5. Mechanical and electrical strain response of a piezoelectric auxetic PZT lattice structure

    Science.gov (United States)

    Fey, Tobias; Eichhorn, Franziska; Han, Guifang; Ebert, Kathrin; Wegener, Moritz; Roosen, Andreas; Kakimoto, Ken-ichi; Greil, Peter

    2016-01-01

    A two-dimensional auxetic lattice structure was fabricated from a PZT piezoceramic. Tape casted and sintered sheets with a thickness of 530 μm were laser cut into inverted honeycomb lattice structure with re-entrant cell geometry (θ = -25°) and poling direction oriented perpendicular to the lattice plane. The in-plane strain response upon applying an uniaxial compression load as well as an electric field perpendicular to the lattice plane were analyzed by a 2D image data detection analysis. The auxetic lattice structure exhibits orthotropic deformation behavior with a negative in-plane Poisson’s ratio of -2.05. Compared to PZT bulk material the piezoelectric auxetic lattice revealed a strain amplification by a factor of 30-70. Effective transversal coupling coefficients {{d}al}31 of the PZT lattice exceeding 4 × 103 pm V-1 were determined which result in an effective hydrostatic coefficient {{d}al}h 66 times larger than that of bulk PZT.

  6. Flexible PET/Al/PZT/Al/PET multi-layered composite for low frequency energy harvesting

    Science.gov (United States)

    Seveno, R.; Carbajo, J.; Dufay, T.; Guiffard, B.; Thomas, J. C.

    2017-04-01

    A flexible piezoelectric device has been realized by depositing lead zirconate titanate (PZT) thin films by chemical solution deposition (CSD) onto very thin aluminium foil (16 µm) and using a polyethylene terephthalate (PET) laminated film (150 µm) as encapsulation. A ruthenium dioxide layer has been used in order to enhance the quality of the PZT/Al interface, improving the dielectric, ferroelectric and piezoelectric properties of the PZT film. The obtained piezoelectric generators have been subjected to large bending motions at low frequencies ranging from 0.1 to 8 Hz and the experimental values of the output voltage, output current and harvested power have been compared to the theoretical values (derived from the electrokinetic model of the piezoelectric material) with very good agreement. Due to the increase of the permittivity of the PZT film by the use of RuO2 interlayer, a moderate decrease of the harvested power at the optimal load resistance is found (from 185 nW to 143 nW at 4.4 Hz), despite the enhancement of the piezoelectric properties. This type of very flexible film, able to withstand a small radius of curvature (1 cm), may yield a promising avenue in the field of low frequency mechanical energy harvesting.

  7. Effect of sintering temperature and composition on microstructure and properties of PMS-PZT ceramics

    Institute of Scientific and Technical Information of China (English)

    DU Hong-liang; PEI Zhi-bin; LI Zhi-min; LUO Fa; ZHU Dong-mei; ZHOU Wan-cheng; QU Shao-bo

    2006-01-01

    The piezoelectric ceramics xPb(Mn1/3Sb2/3)O3-(1-x)Pb(Zr1/2Ti1/2)O3 (abbreviated as PMS-PZT) were synthesized by traditional ceramics process. The effect of sintering temperature and the amount of Pb(Mn1/3Sb2/3)O3 (abbreviated as PMS) on phase structure,microstructure,piezoelectric and dielectric properties of PMS-PZT ceramics was investigated. The results show that the pure perovskite phase is in all ceramics specimens,the phase structure of PMS-PZT ceramics changes from tetragonal phase to single rhombohedral phase with the increasing amount of PMS. The dielectric constant -r,Curie temperature TC,electromechanical coupling factor kp and piezoelectric constant d33 decrease,whereas the mechanical quality factor Qm and dielectric loss tanδ increase with the increasing amount of PMS in system. The optimum sintering temperature is 1 200-1 250 ℃. It is concluded that the PMS-PZT (x=0.07) ceramics sintered at 1 250 ℃ is suitable for high-power piezoelectric transformer. These properties include -r=674.8,tanδ=0.005 25,kp=0.658,Qm1520,d33=230 pC/N,Tc=275 ℃.

  8. Development of the new shape PZT ceramics sounder suitable for a sound source of artificial larynx

    Science.gov (United States)

    Ooe, Katsutoshi; Kanetake, Ryota; Sugio, Yuuichi; Tanaka, Akimitsu

    2007-12-01

    Various speech production substitutes, which aim to reconstruct speech functions, have been developed and used practically by speech impaired individuals. However, conventional speech production substitutes have various drawbacks; therefore, perfect speech production substitutes are expected to be developed. We focused on the PZT ceramics sounder as a sound source in an electric drive artificial larynx. We first developed the artificial larynx that uses a PZT ceramic sounder and then evaluated its performance. The vocalized sound of the artificial larynx user shows good characteristics at the formant frequency, which is important for vowel discrimination. The characteristic feature of our artificial larynx is its individual structure, and this typical structure implies that the sound source and the implant are separated. This structure facilitates a high biocompatibility in our artificial larynx. In our previous work, the improvement in the acoustic characteristics of the sound source was described. The improvement is achieved by the optimization of the electric control and its structure. In this paper, we present the results of shape optimization and new shape PZT ceramics sounder evaluation. The optimized shape is decided on FEM analysis, and prototype PZT ceramics sounder based on above analysis is manufactured by way of trial. Additionally, the performance of prototype sounder is evaluated by acoustic analysis. Until now, we have researched about the immobilization of biomolecules onto the metal surface. It is believed that biomolecular immobilization on the sound source surface improves its biocompatibility. In the future, we aim to realize implantable sound sources that employ biomolecular immobilization technology.

  9. Fabrication and characterization of micromachined high-frequency tonpilz transducers derived by PZT thick films.

    Science.gov (United States)

    Zhou, Qifa; Cannata, Jonathan M; Meyer, Richard J; van Tol, David J; Tadigadapa, Srinivas; Hughes, W Jack; Shung, K Kirk; Trolier-McKinstry, Susan

    2005-03-01

    Miniaturized tonpilz transducers are potentially useful for ultrasonic imaging in the 10 to 100 MHz frequency range due to their higher efficiency and output capabilities. In this work, 4 to 10-microm thick piezoelectric thin films were used as the active element in the construction of miniaturized tonpilz structures. The tonpilz stack consisted of silver/lead zirconate titanate (PZT)/lanthanum nickelate (LaNiO3)/silicon on insulator (SOI) substrates. First, conductive LaNiO3 thin films, approximately 300 nm in thickness, were grown on SOI substrates by a metalorganic decomposition (MOD) method. The room temperature resistivity of the LaNiO3 was 6.5 x 10(-6) omega x m. Randomly oriented PZT (52/48) films up to 7-microm thick were then deposited using a sol-gel process on the LaNiO3-coated SOI substrates. The PZT films with LaNiO3 bottom electrodes showed good dielectric and ferroelectric properties. The relative dielectric permittivity (at 1 kHz) was about 1030. The remanent polarization of PZT films was larger than 26 microC/cm2. The effective transverse piezoelectric e31,f coefficient of PZT thick films was about -6.5 C/m2 when poled at -75 kV/cm for 15 minutes at room temperature. Enhanced piezoelectric properties were obtained on poling the PZT films at higher temperatures. A silver layer about 40-microm thick was prepared by silver powder dispersed in epoxy and deposited onto the PZT film to form the tail mass of the tonpilz structure. The top layers of this wafer were subsequently diced with a saw, and the structure was bonded to a second wafer. The original silicon carrier wafer was polished and etched using a Xenon difluoride (XeF2) etching system. The resulting structures showed good piezoelectric activity. This process flow should enable integration of the piezoelectric elements with drive/receive electronics.

  10. Effects of Pt diffusion barrier layer on the interface reaction and electric properties of PZT film/Si ( 111 ) sample

    Institute of Scientific and Technical Information of China (English)

    ZHU, Yong-Fa(朱永法); CAO, Li-Li(曹立礼); YAN, Pei-Yu(阎培渝); LI, Long-Tu(李龙土); YI, Tao(易涛)

    2000-01-01

    The effects of the Pt diffusion barrier layer on the interface diffusion and reaction, crystallization, dielectric and ferroelectric properties of the PZT/Si(111) sample have been studied using XPS, AES and XRD techniques. The results indicate that the Pt diffusion barrier layer between the PZT layer and the Si substrate prohibits the formation of TiCx, TiSix and SiO2 species in the PZT layer. The Pt barrier layer also completely interrupts the diffusion of Si from the Si substrate into the PZT layer and impedes the diffusion of oxygen from air to the Si substrate greatly. Although the Pt layer can not prevent completely the diffusion and reaction between oxygen and silicon, it can prevent the formation of a stable SiO2 interface layer on the interface of PZT/Si. The Pt layer reacts with silicon to form PtSix species on the interface of Pt/Si, which can intensify the chemical binding strength between the Pt layer and the Si substrate. To play a good role as a diffusion barrier layer, the Pt barrier layer must be not thinner than 140 nm. The existence of the Pt layer not only promotes the crystallization of PZT layer to form a perovskite phase but also improves dielectric and ferroelectric performances of the PZT layer.

  11. Fabrication and properties of SmFe2-PZT magnetoelectric thin films

    KAUST Repository

    Giouroudi, Ioanna

    2013-05-17

    Magnetoelectric (ME) thin film composites are attracting a continually increasing interest due to their unique features and potential applications in multifunctional microdevices and integrated units such as sensors, actuators and energy harvesting modules. By combining piezoelectric and highly magnetostrictive thin films, the potentialities of these materials increase. In this paper we report the fabrication of SmFe2 and PZT thin films and the investigation of their properties. First of all, a ~ 400 nm thin SmFe film was deposited on top of Si/SiO2 substrate by magnetron sputter deposition. Afterwards, a 140 nm Pt bottom electrode was sputtered on top of the SmFe film forming a bottom electrode. Spin coating was employed for the deposition of the 150 nm thin PZT layer. A PZT solution with 10 %Pb excess was utilized for this fabrication step. Finally, circular Pt top electrodes were sputtered as top electrodes. This paper focuses on the microstructure of the individual films characterized by X-Ray diffractometer (XRD) and scanning electron microscopy (SEM). A piezoelectric evaluation system, aixPES, with TF2000E analyzer component was used for the electric hysteresis measurements of PZT thin films and a vibrating sample magnetometer (VSM) was employed for the magnetic characterization of the SmFe. The developed thin films and the fabricated double layer SmFe-PZT exhibit both good ferromagnetic and piezoelectric responses which predict a promising ME composite structure. The quantitative chemical composition of the samples was confirmed by energy dispersive spectroscopy (EDX). © (2013) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

  12. Sputter deposition of PZT piezoelectric films on thin glass substrates for adjustable x-ray optics.

    Science.gov (United States)

    Wilke, Rudeger H T; Johnson-Wilke, Raegan L; Cotroneo, Vincenzo; Davis, William N; Reid, Paul B; Schwartz, Daniel A; Trolier-McKinstry, Susan

    2013-05-10

    Piezoelectric PbZr(0.52)Ti(0.48)O(3) (PZT) thin films deposited on thin glass substrates have been proposed for adjustable optics in future x-ray telescopes. The light weight of these x-ray optics enables large collecting areas, while the capability to correct mirror figure errors with the PZT thin film will allow much higher imaging resolution than possible with conventional lightweight optics. However, the low strain temperature and flexible nature of the thin glass complicate the use of chemical-solution deposition due to warping of the substrate at typical crystallization temperatures for the PZT. RF magnetron sputtering enabled preparation of PZT films with thicknesses up to 3 μm on Schott D263 glass substrates with much less deformation. X-ray diffraction analysis indicated that the films crystallized with the perovskite phase and showed no indication of secondary phases. Films with 1 cm(2) electrodes exhibited relative permittivity values near 1100 and loss tangents below 0.05. In addition, the remanent polarization was 26 μC/cm(2) with coercive fields of 33 kV/cm. The transverse piezoelectric coefficient was as high as -6.1±0.6 C/m(2). To assess influence functions for the x-ray optics application, the piezoelectrically induced deflection of individual cells was measured and compared with finite-element-analysis calculations. The good agreement between the results suggests that actuation of PZT thin films can control mirror figure errors to a precision of about 5 nm, allowing sub-arcsecond imaging.

  13. Influence of binding material of PZT coating on microresonator's electrical and mechanical properties

    Science.gov (United States)

    Janusas, Giedrius; Guobiene, Asta; Palevicius, Arvydas; Brunius, Alfredas; Cekas, Elingas; Baltrusaitis, Valentinas; Sakalys, Rokas

    2017-06-01

    Microresonators are fundamental components integrated in hosts of MEMS applications: covering the automotive sector, the telecommunication industry, electronic equipment for surface/material characterization and motion sensing, and etc. The aim of this paper is to investigate the mechanical and electrical properties of PZT film fabricated with three binding materials: polyvinyl butyral (PVB), polymethyl methacrylate (PMMA) and polystyrene (PS) and to evaluate applicability in control of microresonators Q factor. Micro particles of PZT powder were mixed with 20% solution of PVB, PMMA and PS in benzyl alcohol. For investigation of mechanical and electrical properties multilayer cantilevers were made. Obtained PZT and polymer paste was screen printed on copper (thickness 40 μm) using polyester monofilament screen meshes (layer thickness 50 μm) and dried for 30 min at 100°C. Electric dipoles of the PZT particles in composite material were aligned using high voltage generator (5 kV) and a custom-made holder. Electric field was held for 30 min. Surfaces of the applied films were investigated by Atomic Force Microscope NanoWizard(R)3 NanoScience. Dynamic and electrical characteristics of the multilayer were investigated using laser triangular displacement sensor LK-G3000. The measured vibration amplitude and generated electrical potential was collected with USB oscilloscope PicoScope 3424. As the results showed, these cantilevers were able to transform mechanical strain energy into electric potential and, v.v. However, roughness of PZT coatings with PMMA and PS were higher, what could be the reason of the worse quality of the top electrode. However, the main advantage of the created composite piezoelectric material is the possibility to apply it on any uniform or non-uniform vibrating surface and to transform low frequency vibrations into electricity.

  14. Chem-Prep PZT 95/5 for neutron generator applications : development of laboratory-scale powder processing operations.

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Ted V.; Moore, Roger Howard; Spindle, Thomas Lewis Jr.

    2003-12-01

    Chemical synthesis methods are being developed as a future source of PZT 95/5 powder for neutron generator voltage bar applications. Laboratory-scale powder processes were established to produce PZT billets from these powders. The interactions between calcining temperature, sintering temperature, and pore former content were studied to identify the conditions necessary to produce PZT billets of the desired density and grain size. Several binder systems and pressing aids were evaluated for producing uniform sintered billets with low open porosity. The development of these processes supported the powder synthesis efforts and enabled comparisons between different chem-prep routes.

  15. Design, Modeling and Optimization of a Piezoelectric Pressure Sensor based on a Thin-Film PZT Membrane Containing Nanocrystalline Powders

    National Research Council Canada - National Science Library

    Vahid Mohammadi; Mohammad Hossein Sheikhi

    2009-01-01

    ...^ thin film has been presented and then a pressure sensor based on multilayer thin-film PZT diaphragm contain of Lead Zirconate Titanate nanocrystalline powders was designed, modeled and optimized...

  16. A Piezoelectric PZT Ceramic Mulitlayer Stack for Energy Harvesting Under Dynamic Forces

    Science.gov (United States)

    Xu, Tian-Bing; Siochi, Emilie J.; Kang, Jin Ho; Zuo, Lei; Zhou, Wanlu; Tang, Xiudong; Jiang, Xiaoning

    2011-01-01

    Piezoelectric energy harvesting transducers (PEHTs) are commonly used in motion/vibration energy scavenging devices. To date, most researchers have focused on energy harvesting at narrow bandwidths around the mechanical resonance frequency, and most piezoelectric harvesting devices reported in the literature have very low effective piezoelectric coefficient (d(sub eff)) (piezoelectric coefficients of about 100 pC/N. The level of harvested electrical power for CBPEHTs is on the order of microW even at resonance mode. In order to harvest more electrical energy across broader bandwidth, high effective piezoelectric coefficient structures are needed. In this study, we investigate a "33" longitudinal mode, piezoelectric PZT ceramic multilayer stack (PZT-Stack) with high effective piezoelectric coefficient for high-performance PEHTs. The PZT-Stack is composed of 300 layers of 0.1 mm thick PZT plates, with overall dimensions of 32.4 mm X 7.0 mm X 7.0 mm. Experiments were carried out with dynamic forces in a broad bandwidth ranging from 0.5 Hz to 25 kHz. The measured results show that the effective piezoelectric coefficient of the PZT-stack is about 1 X 10(exp 5) pC/N at off-resonance frequencies and 1.39 X 10(exp 6) pC/N at resonance, which is order of magnitude larger than that of traditional PEHTs. The effective piezoelectric coefficients (d(sub eff)) do not change significantly with applied dynamic forces having root mean square (RMS) values ranging from 1 N to 40 N. In resonance mode, 231 mW of electrical power was harvested at 2479 Hz with a dynamic force of 11.6 N(sub rms), and 7.6 mW of electrical power was generated at a frequency of 2114 Hz with 1 N(sub rms) dynamic force. In off-resonance mode, an electrical power of 18.7 mW was obtained at 680 Hz with a 40 N(sub rms) dynamic force. A theoretical model of energy harvesting for the PZT-Stack is established. The modeled results matched well with experimental measurements. This study demonstrated that high

  17. A Piezoelectric PZT Ceramic Mulitlayer Stack for Energy Harvesting Under Dynamic Forces

    Science.gov (United States)

    Xu, Tian-Bing; Siochi, Emilie J.; Kang, Jin Ho; Zuo, Lei; Zhou, Wanlu; Tang, Xiudong; Jiang, Xiaoning

    2011-01-01

    Piezoelectric energy harvesting transducers (PEHTs) are commonly used in motion/vibration energy scavenging devices. To date, most researchers have focused on energy harvesting at narrow bandwidths around the mechanical resonance frequency, and most piezoelectric harvesting devices reported in the literature have very low effective piezoelectric coefficient (d(sub eff)) (harvested electrical power for CBPEHTs is on the order of microW even at resonance mode. In order to harvest more electrical energy across broader bandwidth, high effective piezoelectric coefficient structures are needed. In this study, we investigate a "33" longitudinal mode, piezoelectric PZT ceramic multilayer stack (PZT-Stack) with high effective piezoelectric coefficient for high-performance PEHTs. The PZT-Stack is composed of 300 layers of 0.1 mm thick PZT plates, with overall dimensions of 32.4 mm X 7.0 mm X 7.0 mm. Experiments were carried out with dynamic forces in a broad bandwidth ranging from 0.5 Hz to 25 kHz. The measured results show that the effective piezoelectric coefficient of the PZT-stack is about 1 X 10(exp 5) pC/N at off-resonance frequencies and 1.39 X 10(exp 6) pC/N at resonance, which is order of magnitude larger than that of traditional PEHTs. The effective piezoelectric coefficients (d(sub eff)) do not change significantly with applied dynamic forces having root mean square (RMS) values ranging from 1 N to 40 N. In resonance mode, 231 mW of electrical power was harvested at 2479 Hz with a dynamic force of 11.6 N(sub rms), and 7.6 mW of electrical power was generated at a frequency of 2114 Hz with 1 N(sub rms) dynamic force. In off-resonance mode, an electrical power of 18.7 mW was obtained at 680 Hz with a 40 N(sub rms) dynamic force. A theoretical model of energy harvesting for the PZT-Stack is established. The modeled results matched well with experimental measurements. This study demonstrated that high effective piezoelectric coefficient structures enable PEHTs to

  18. Magnetoelectric Responses of GMM/PZT/GMM Laminate Composite in Longitudinal Vibration%GMM/PZT/GMM层合材料的纵振磁电响应

    Institute of Scientific and Technical Information of China (English)

    文玉梅; 周丽萍; 李平; 卞雷祥

    2009-01-01

    The adhesive layers and the mechanical losses of materials in giant magnetostrictive material (GMM) and piezoelectric Pb(Zr,Ti)O3 (PZT) laminate composites are vital factors to impact final magneto-electric responses. The effects of the adhesive layer resulting from the shear and longitudinal deformation were considered in the governing motion equations of GMM/PZT/GMM composites, which were established based on Hamilton's principle. The coefficients in the motion equations were specified by the material parameters. To introduce the material losses into the analysis, the mechanical parameters including the compliances of magnetostrictive and piezoelectric materials were represented as complexes. Through the motion equations along with the boundary conditions and the constitutive equations of magnetostrictive/piezoelectric effects, the magnetoelectric responses over frequency and the natural frequencies were provided. The numerical calculations of the magnetoelectric responses in GMM/PZT/GMM laminate composite was presented. By comparing the theoretical magnetoelectric response with the experimental result,shows that the introduction of material losses can provide more acceptable prediction of the magnetoelectric performances.%层状复合结构层间胶层和复合材料的机械损耗是影响层状磁电复合材料磁电响应的重要因素.为了考虑层间胶层的作用,包括其纵向变形和剪切变形产生的效果,应用Hamilton原理建立层状复合结构的运动方程,并用复柔顺系数来反映材料的机械损耗特性.结合层状复合结构的边界条件和磁致伸缩/压电本构方程,就可以得到考虑了胶层作用和材料损耗时,复合结构的固有频率和磁电响应.对GMM(超磁致伸缩材料)/PZT(压电材料)/GMM结构的磁电响应进行了数值计算,将计算结果与实验结果进行了比较,证明考虑胶层作用并引入材料的损耗能够更准确预测复合材料的磁电换能特性.

  19. A hybrid phenomenological model for ferroelectroelastic ceramics. Part II: Morphotropic PZT ceramics

    Science.gov (United States)

    Stark, S.; Neumeister, P.; Balke, H.

    2016-10-01

    In this part II of a two part series, the rate-independent hybrid phenomenological constitutive model introduced in part I is modified to account for the material behavior of morphotropic lead zirconate titanate ceramics (PZT ceramics). The modifications are based on a discussion of the available literature results regarding the micro-structure of these materials. In particular, a monoclinic phase and a highly simplified representation of the hierarchical structure of micro-domains and nano-domains observed experimentally are incorporated into the model. It is shown that experimental data for the commercially available morphotropic PZT material PIC151 (PI Ceramic GmbH, Lederhose, Germany) can be reproduced and predicted based on the modified hybrid model.

  20. Fluid Vessel Quantity Using Non-invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  1. Temperature and strain rate effects on the piezoelectric charge production of PZT 95/5

    Science.gov (United States)

    Khan, Amnah S.; Proud, William G.

    2017-01-01

    To develop a better understanding of the piezoelectric ceramic lead zirconate titanate (PZT) 95/5, parameters including varying temperatures, porosities and strain rates have been studied. The effects on the charge output and fracture of poled PZT samples of different porosities have been investigated with compressive strain rates (10-4 - 10+3 s-1) using quasi-static loading equipment, drop-weight towers and Split Hopkinson Pressure Bars (SHPBs). The cylindrical specimens were of 4.4 mm diameter, thickness 0.8 - 4.4 mm, and density 7.3 - 8.3 g cm-3. The temperature range of -20 °C to +80 °C was achieved using purpose-built environmental chambers. The resulting stress-strain relationships are compared; all the samples ultimately displayed a brittle response at failure [1].

  2. Dielectric and Piezoelectric Properties of 0-3 PZT/PVDF Composite Doped with Polyaniline

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Lead zirconate titanate (PZT)/polyvinylidenc fluoride (PVDF) 0- 3 piezoelectric composites doped with polyaniline (PANI) were obtained by hot-press method.The polarization properties of the composites were characterized by XRD and P- E hysteresis loops at room temperature.And the dielectric and piezoelectric properties were also measured.The results show that the poling of PZT could be effectively carried out and the dielectric constant εr and dissipation tanδ increase monotonously by increasing the voltme fraction of PANI in the composite.The piezoelectric constant d33, and the planar electromechanical coupling factor kp increase while the mechanical quality factor Qm decreases with the increase in the content of PANI.The d33 , kp and Qm show the extremum valnes at 8 vol%-10 vol% PANI.

  3. Dielectric response of capacitor structures based on PZT annealed at different temperatures

    Science.gov (United States)

    Kamenshchikov, Mikhail V.; Solnyshkin, Alexander V.; Pronin, Igor P.

    2016-12-01

    Dielectric response of thin-film capacitor structures of Pt/PZT/Pt deposited by the RF magnetron sputtering method and annealed at temperatures of 540-570 °C was investigated. It was found that dielectric properties of these structures depend on the synthesis temperature. Stability of a polarized state is considered on the basis of the analysis of hysteresis loops and capacitance-voltage (C-V) characteristics. The contribution of the domain mechanism in the dielectric response of the capacitor structure comprising a ferroelectric is discussed. Extreme dependences of electrophysical characteristics of PZT films on their synthesis temperature were observed. Correlation of dielectric properties with microstructure of these films is found out.

  4. Characterization and comparison of PZT powder synthesis by solid state and sol gel methods

    Directory of Open Access Journals (Sweden)

    E Pakizeh

    2012-09-01

    Full Text Available   This paper describes the synthesis of Pb(Zr0.95Ti0.05O3 powder by sol gel and solid state methods. PZT powders were fabricated by solid-state reaction process using metal oxides and in sol gel method salts and organic compounds were employed. The powders were calcined at 700 and 950 oC in sol gel and solid state methods, respectively. The synthesized powders were analyzed by FTIR and XRD. The average crystal grain size of PZT powders determined by X-ray diffraction method using the Scherrer equation, and in sol gel and solid state methods measured 42 and 330 nm, respectively. The optical constants of powders were evaluated and compaed using FTIR transmittance spectroscopy and Kramers-Kronig analysis.

  5. Effect of electric field, stress and environment on delayed fracture of a PZT-5 ferroelectric ceramic

    Institute of Scientific and Technical Information of China (English)

    WANG; Yi; SU; Yanjing; CHU; Wuyang; QIAO; Lijie

    2005-01-01

    The combined effect of electric and mechanical loading on fracture of a PZT-5 ferroelectric ceramic in silicone oil has been investigated using a single edge notched specimen. The results show that the fracture toughness and the threshold stress intensity factor of delayed fracture in silicone oil, i.e. stress corrosion cracking, decrease linearly with the increasing applied electric field, either positive or negative. For the PZT-5 ferroelectric ceramics, delayed fracture in silicone oil under sustained positive or negative field can occur, and the threshold field for delayed fracture under sustained positive or negative field decreases linearly with applied stress intensity factor. The combined effect of electric and mechanical loading on delayed fracture in silicone oil includes fieldenhancing delayed fracture under sustained load and stress-enhancing delayed fracture in silicone oil under sustained field.

  6. Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A.

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  7. Microstructure and Electromechanical Properties in PMnN-PZT Ceramics Sintered at Different Temperatures

    Institute of Scientific and Technical Information of China (English)

    Baoshan LI; Zhigang ZHU; Guorong LI; Aili DING

    2005-01-01

    The microstructure and piezoelectric properties of Pb[(Zr0.52Ti0.48)0.95(Mn1/3Nb2/3)0.05]O3 (PMnN-PZT) ceramics have been investigated at different sintering temperatures from 1070℃ to 1280℃. The experimental results suggest that grain sizes and electromechanical properties of the ceramics show strong sintering temperature dependences.Double polarization to electric field (P-E) loops of the PMnN-PZT ceramics are assumed to be the result of the pinning effect of the defect dipoles. The results obtained through X-ray photoelectron spectrum suggest that sintering temperature affects valence of the Mn ion and quantity of oxygen vacancies. Hence, a proper explanation is proposed to illustrate the fluctuation of mechanical quality factor (Qm) due to the sintering temperature.

  8. Electrodynamic properties of porous PZT-Pt films at terahertz frequency range

    Energy Technology Data Exchange (ETDEWEB)

    Komandin, Gennady A.; Porodinkov, Oleg E.; Spektor, Igor E.; Volkov, Alexander A. [Prokhorov General Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation); Vorotilov, Konstantin A.; Seregin, Dmitry S.; Sigov, Alexander S. [Moscow Technological University (MIREA), Moscow (Russian Federation)

    2017-01-15

    Electrodynamics of Si-SiO{sub 2}-TiO{sub 2}-Pt-PZT heterostructures is studied in the frequency range from 5 to 5000 cm{sup -1} by monochromatic BWO (backward wave oscillator) and infrared Fourier-transform spectroscopy techniques to derive the dielectric characteristics of the sol-gel porous ferroelectric PbZr{sub 0.48}Ti{sub 0.52}O{sub 3} films. Broad frequency band dielectric response of PZT films with different density is constructed using the oscillator dispersion models. The main contribution to the film permittivity is found to form at frequencies below 100 cm{sup -1} depending strongly and non-linearly on the film medium density. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Local piezoelectric behavior in PZT-based thin films for ultrasound transducers

    Science.gov (United States)

    Griggio, Flavio

    Piezoelectric microelectromechanical systems (MEMS) are currently used in inkjet printers and precision resonators; numerous additional applications are being investigated for sensors, low-voltage actuators, and transducers. This work was aimed at improving piezoelectric MEMS by taking two approaches: 1) identifying factors affecting the piezoelectric response of ferroelectric thin films and 2) demonstrating integration of these films into a high frequency array transducer. It was found that there are several key factors influencing the piezoelectric response of thin films for a given material composition. First, large grain size improves the piezoelectric response. This was demonstrated using chemical solution deposited lead nickel niobate -- lead zirconate titanate (0.3)Pb(Ni 0.33Nb0.67)O3 - (0.7)Pb(Zr0.45Ti 0.55O3), (PNN-PZT) ferroelectric thin films. It was shown that this composition allows greater microstructural control than does PZT. Dielectric permittivities ranging from 1350 to 1520 and a transverse piezoelectric coefficient e31,f as high as -- 9.7 C/m 2 were observed for films of about 0.25 mum in thickness. The permittivity and piezoelectric response as well as extrinsic contributions to the dielectric constant increased by 14 and 12 % respectively for samples with grain sizes ranging from 110 to 270 nm. A second factor influencing the piezoelectric response is film composition with respect to the morphotropic phase boundary (MPB). The composition dependence of the dielectric and piezoelectric nonlinearities was characterized in epitaxially grown (0.3)Pb(Ni0.33Nb0.67)O3-(0.7)Pb(Zr xTi1-xO3) thin films deposited on SrTiO 3 to minimize the influence of large-angle grain boundaries. Tetragonal, MPB and rhombohedral films were prepared by changing the Zr/Ti ratio. The largest dielectric and piezoelectric nonlinearities were observed for the rhombohedral sample; this resulted from a higher domain wall mobility due to a smaller ferroelectric distortion and

  10. Finite Element Analysis of Single Cell Stiffness Measurements Using PZT-Integrated Buckling Nanoneedles

    Directory of Open Access Journals (Sweden)

    Maryam Alsadat Rad

    2016-12-01

    Full Text Available This paper proposes a new technique for real-time single cell stiffness measurement using lead zirconate titanate (PZT-integrated buckling nanoneedles. The PZT and the buckling part of the nanoneedle have been modelled and validated using the ABAQUS software. The two parts are integrated together to function as a single unit. After calibration, the stiffness, Young’s modulus, Poisson’s ratio and sensitivity of the PZT-integrated buckling nanoneedle have been determined to be 0.7100 N·m−1, 123.4700 GPa, 0.3000 and 0.0693 V·m·N−1, respectively. Three Saccharomyces cerevisiae cells have been modelled and validated based on compression tests. The average global stiffness and Young’s modulus of the cells are determined to be 10.8867 ± 0.0094 N·m−1 and 110.7033 ± 0.0081 MPa, respectively. The nanoneedle and the cell have been assembled to measure the local stiffness of the single Saccharomyces cerevisiae cells The local stiffness, Young’s modulus and PZT output voltage of the three different size Saccharomyces cerevisiae have been determined at different environmental conditions. We investigated that, at low temperature the stiffness value is low to adapt to the change in the environmental condition. As a result, Saccharomyces cerevisiae becomes vulnerable to viral and bacterial attacks. Therefore, the proposed technique will serve as a quick and accurate process to diagnose diseases at early stage in a cell for effective treatment.

  11. Development of dual PZT transducers for reference-free crack detection in thin plate structures.

    Science.gov (United States)

    Sohn, Hoon; Kim, Seuno Bum

    2010-01-01

    A new Lamb-wave-based nondestructive testing (NDT) technique, which does not rely on previously stored baseline data, is developed for crack monitoring in plate structures. Commonly, the presence of damage is identified by comparing "current data" measured from a potentially damaged stage of a structure with "baseline data" previously obtained at the intact condition of the structure. In practice, structural defects typically take place long after collection of the baseline data, and the baseline data can be also affected by external loading, temperature variations, and changing boundary conditions. To eliminate the dependence on the baseline data comparison, the authors previously developed a reference-free NDT technique using 2 pairs of collocated lead zirconate titanate (PZT) transducers placed on both sides of a plate. This reference-free technique is further advanced in the present study by the necessity of attaching transducers only on a single surface of a structure for certain applications such as aircraft. To achieve this goal, a new design of PZT transducers called dual PZT transducers is proposed. Crack formation creates Lamb wave mode conversion due to a sudden thickness change of the structure. This crack appearance is instantly detected from the measured Lamb wave signals using the dual PZT transducers. This study also suggests a reference-free statistical approach that enables damage classification using only the currently measured data set. Numerical simulations and experiments were conducted using an aluminum plate with uniform thickness and fundamental Lamb waves modes to demonstrate the applicability of the proposed technique to reference-free crack detection.

  12. The study of dielectric, pyroelectric and piezoelectric properties on hot pressed PZT-PMN systems

    Energy Technology Data Exchange (ETDEWEB)

    Srivastava, Geetika; Umarji, A. M. [Materials Research Centre, Indian Institute of Science, Bangalore-560 012 (India); Maglione, Mario [ICMCB, Universite de Bordeaux,-CNRS, 87, Av Dr Schweitzer 33806 Pessac (France)

    2012-12-15

    Hot uniaxial pressing technique has been adopted for the densification of PZT-PMN system with an aim to yield dense ceramics and to lower the sintering temperature and time for achieving better and reproducible electronic properties. The ceramics having >97% theoretical density and micron size grains are investigated for their dielectric, pyroelectric and piezoelectric properties. The effect of Li and Mn addition has also been studied.

  13. The study of dielectric, pyroelectric and piezoelectric properties on hot pressed PZT-PMN systems

    Directory of Open Access Journals (Sweden)

    Geetika Srivastava

    2012-12-01

    Full Text Available Hot uniaxial pressing technique has been adopted for the densification of PZT-PMN system with an aim to yield dense ceramics and to lower the sintering temperature and time for achieving better and reproducible electronic properties. The ceramics having >97% theoretical density and micron size grains are investigated for their dielectric, pyroelectric and piezoelectric properties. The effect of Li and Mn addition has also been studied.

  14. Improvement of the fatigue and the ferroelectric properties of PZT films through a LSCO seed layer

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Sofia A.S., E-mail: sofiarodrigues@fisica.uminho.pt; Silva, José P.B.; Khodorov, Anatoli; Martín-Sánchez, Javier; Pereira, M.; Gomes, M.J.M.

    2013-11-01

    Highlights: • Pulsed laser deposited PZT thin films. • Seed layer effect on the structural and ferroelectric properties of the PZT films. • The stability of P{sub r} was improved with the introduction of the LSCO layer. -- Abstract: The ability to optimizate the preparation of Lead Zirconate Titanate (PZT) films on platinized Si substrate by pulsed laser deposition was demonstrated. The effect of the modification of the interface film/electrode through the use of a (La,Sr)CoO{sub 3} (LSCO) seed layer on the remnant polarization, fatigue endurance and stress in PZT films was studied. An improvement on the ferroelectric properties was found with the using of the LSCO layer. A remnant polarization (P{sub r}) of 19.8 μC/cm{sup 2} and 4.4 μC/cm{sup 2} for films with and without the LSCO layer were found. In the same way the polarization fatigue decreases significantly after deposition of the LSCO layer between the film and substrate. Atomic force microscopy (AFM) images revealed a different growth process in the films. Current–voltage (I–V) measurements showed that the use of LSCO seed layer improves the leakage current and, on the other hand the conduction mechanisms in the film without LSCO, after the fatigue test, was found to be changed from Schottky to Poole–Frenkel. The trap activation energy (about 0.14 eV) determined from Poole–Frenkel mode agrees well with the energy level of oxygen vacancies. The films stresses were estimated by XRD in order to explain the improvement on the structure and consequentially ferroelectric properties of the films. The model proposed by Dawber and Scott was found to be in agreement with our experimental data, which seems to predict that the oxygen vacancies play an important role on fatigue.

  15. Structure and Physical Properties of PZT-PMnN-PSN Ceramics Near the Morphological Phase Boundary

    Directory of Open Access Journals (Sweden)

    Nguyen Dinh Tung Luan

    2014-01-01

    Full Text Available The 0.9Pb(ZrxTi1−xO3-0.07Pb(Mn1/3Nb2/3O3-0.03Pb(Sb1/2Nb1/2O3 (PZT-PMnN-PSN ceramics were prepared by columbite method. The phase structure of the ceramic samples was analyzed. Results show that the pure perovskite phase is in all ceramics specimens. The effect of the Zr/Ti ratio on the region of morphotropic phase boundary for PZT-PMnN-PSN ceramics was studied. Experimental results show that the phase structure of ceramics changes from tetragonal to rhombohedral with the increase of the content of Zr/Ti ratio in the system. The composition of PZT-PMnN-PSN ceramics near the morphotropic phase boundary obtained is the ratio of Zr/Ti: 49/51. At this ratio, the ceramic has the optimal electromechanical properties: the kp=0.61, the εmax=29520, the d31=-236 pC/N, the Qm=2400, high remanent polarization (Pr=49.2 μC·cm−2, and low coercive field Ec=10.28 kV·cm−1.

  16. Thin PZT-Based Ferroelectric Capacitors on Flexible Silicon for Nonvolatile Memory Applications

    KAUST Repository

    Ghoneim, Mohamed T.

    2015-04-24

    A flexible version of traditional thin lead zirconium titanate ((Pb1.1Zr0.48Ti0.52O3)-(PZT)) based ferroelectric random access memory (FeRAM) on silicon shows record performance in flexible arena. The thin PZT layer requires lower operational voltages to achieve coercive electric fields, reduces the sol-gel coating cycles required (i.e., more cost-effective), and, fabrication wise, is more suitable for further scaling of lateral dimensions to the nano-scale due to the larger feature size-to-depth aspect ratio (critical for ultra-high density non-volatile memory applications). Utilizing the inverse proportionality between substrate\\'s thickness and its flexibility, traditional PZT based FeRAM on silicon is transformed through a transfer-less manufacturable process into a flexible form that matches organic electronics\\' flexibility while preserving the superior performance of silicon CMOS electronics. Each memory cell in a FeRAM array consists of two main elements; a select/access transistor, and a storage ferroelectric capacitor. Flexible transistors on silicon have already been reported. In this work, we focus on the storage ferroelectric capacitors, and report, for the first time, its performance after transformation into a flexible version, and assess its key memory parameters while bent at 0.5 cm minimum bending radius.

  17. Piezoelectric and dielectric characterization of corona and contact poled PZT-epoxy-MWCNT bulk composites

    Science.gov (United States)

    Banerjee, S.; Cook-Chennault, K. A.; Du, W.; Sundar, U.; Halim, H.; Tang, A.

    2016-11-01

    Three-phase lead zirconate titanate (PZT, PbZr0.52Ti0.48O3)-epoxy-multi-walled carbon nanotube (MWCNT) bulk composites were prepared, where the volume fraction of PZT was held constant at 30%, while the volume fraction of the MWCNTs was varied from 1.0%-10%. The samples were poled using either a parallel plate contact or contactless (corona) poling technique. The piezoelectric strain coefficient (d 33), dielectric constant (ɛ), and dielectric loss tangent (tan δ) of the samples were measured at 110 Hz, and compared as a function of poling technique and volume fraction of MWCNTs. The highest values for dielectric constant and piezoelectric strain coefficients were 465.82 and 18.87 pC/N for MWCNT volume fractions of 10% and 6%, respectively. These values were obtained for samples that were poled using the corona contactless method. The impedance and dielectric spectra of the composites were recorded over a frequency range of 100 Hz-20 MHz. The impedance values observed for parallel-plate contact poled samples are higher than that of corona poled composites. The fractured surface morphology and distribution of the PZT particles and MWCNTs were observed with the aid of electron dispersion spectroscopy and a scanning electron microscope. The surface morphology of the MWCNTs was observed with the aid of a field emission transmission electron microscope.

  18. Effect of solid content variations on PZT slip for tape casting

    Directory of Open Access Journals (Sweden)

    Gang Jian

    2012-12-01

    Full Text Available Lead zirconate titanate (PZT particles with pure tetragonal structure were synthesized by solid-state reaction method and used for preparation of slurries with different solid contents (34–80 wt.%. Then, PZT thick films were fabricated by the nonaqueous tape casting method. It was shown that the slurry prepared from ball-milled particles exhibited better rheology properties than slurry from particles which were not ball-milled. Measurement of sedimentation volumes and zeta potentials indicated particle aggregation, resulting in weak stability of the slurries with high solid contents. The microstructure, piezoelectric and ferroelectric properties of PZT sintered films were investigated in terms of solid contents. Ceramic films prepared from the slurry with solid contents of 73 wt.% had the optimal structure and properties. After poling at 200 °C with an applied field of 1.2 kV/cm, a d33 of 294 pC/N was achieved; typical ferroelectric properties were also observed with a Ps of 38 μC/cm2.

  19. Lithographic definition of channel and void structures in multilayer PZT microactuators

    Science.gov (United States)

    Rosqvist, Tobias; Johansson, Stefan A. I.

    1999-10-01

    We are investigating techniques to fabricate advanced microactuators cost efficiently and in particular to combine silicon microstructures with multilayer PZT microelements. Aiming at an increased freedom in design of multilayer PZT elements, various process steps to build channel and void structures in the actuator body are investigated. In a multilayer actuator, channels and voids can be used for transportation of fluids or to change transducer properties. A PZT green ceramic body is built with internal sacrificial structures defined using photolithography and patterned polymer foil and these structures are removed during binder burnout. In difference to conventional green tape lamination the technique used in the presented experiments, wet building, tends to planarize consecutive layers cast. This is particularly advantageous for high aspect ratio sacrificial structures. Results show that possible channel dimensions range from 10 micrometers up to above 200 micrometers . The lower channel dimension limitation is determined by the surface roughness of a cast green layer and the grain growth during sintering. No sagging of the channels is observed at the investigated channel dimensions. The mechanical and chemical stability of the sacrificial material during exposure to solvent and moderate heat is found to be important. The large scale manufacturing aspect of the investigated technique is also discussed.

  20. The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT

    Directory of Open Access Journals (Sweden)

    Christoph Slouka

    2016-11-01

    Full Text Available The different properties of acceptor-doped (hard and donor-doped (soft lead zirconate titanate (PZT ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La3+ donor-doped, Fe3+ acceptor-doped and La3+/Fe3+-co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT.

  1. The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT)

    Science.gov (United States)

    Slouka, Christoph; Kainz, Theresa; Navickas, Edvinas; Walch, Gregor; Hutter, Herbert; Reichmann, Klaus; Fleig, Jürgen

    2016-01-01

    The different properties of acceptor-doped (hard) and donor-doped (soft) lead zirconate titanate (PZT) ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La3+ donor-doped, Fe3+ acceptor-doped and La3+/Fe3+-co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT. PMID:28774067

  2. Temperature dependent mechanical property of PZT film: an investigation by nanoindentation.

    Directory of Open Access Journals (Sweden)

    Yingwei Li

    Full Text Available Load-depth curves of an unpoled Lead Zirconate Titanate (PZT film composite as a function of temperature were measured by nanoindentation technique. Its reduce modulus and hardness were calculated by the typical Oliver-Pharr method. Then the true modulus and hardness of the PZT film were assessed by decoupling the influence of substrate using methods proposed by Zhou et al. and Korsunsky et al., respectively. Results show that the indentation depth and modulus increase, but the hardness decreases at elevated temperature. The increasing of indentation depth and the decreasing of hardness are thought to be caused by the decreasing of the critical stress needed to excite dislocation initiation at high temperature. The increasing of true modulus is attributed to the reducing of recoverable indentation depth induced by back-switched domains. The influence of residual stress on the indentation behavior of PZT film composite was also investigated by measuring its load-depth curves with pre-load strains.

  3. Design Optimization of PZT-Based Piezoelectric Cantilever Beam by Using Computational Experiments

    Science.gov (United States)

    Kim, Jihoon; Park, Sanghyun; Lim, Woochul; Jang, Junyong; Lee, Tae Hee; Hong, Seong Kwang; Song, Yewon; Sung, Tae Hyun

    2016-08-01

    Piezoelectric energy harvesting is gaining huge research interest since it provides high power density and has real-life applicability. However, investigative research for the mechanical-electrical coupling phenomenon remains challenging. Many researchers depend on physical experiments to choose devices with the best performance which meet design objectives through case analysis; this involves high design costs. This study aims to develop a practical model using computer simulations and to propose an optimized design for a lead zirconate titanate (PZT)-based piezoelectric cantilever beam which is widely used in energy harvesting. In this study, the commercial finite element (FE) software is used to predict the voltage generated from vibrations of the PZT-based piezoelectric cantilever beam. Because the initial FE model differs from physical experiments, the model is calibrated by multi-objective optimization to increase the accuracy of the predictions. We collect data from physical experiments using the cantilever beam and use these experimental results in the calibration process. Since dynamic analysis in the FE analysis of the piezoelectric cantilever beam with a dense step size is considerably time-consuming, a surrogate model is employed for efficient optimization. Through the design optimization of the PZT-based piezoelectric cantilever beam, a high-performance piezoelectric device was developed. The sensitivity of the variables at the optimum design is analyzed to suggest a further improved device.

  4. Application of Multiplexed FBG and PZT Impedance Sensors for Health Monitoring of Rocks

    Directory of Open Access Journals (Sweden)

    Yingxin Zhou

    2008-01-01

    Full Text Available Reliable structural health monitoring (SHM including nondestructiveevaluation (NDE is essential for safe operation of infrastructure systems. Effectivemonitoring of the rock components of civil infrastructures such as tunnels and cavernsremains challenging. The feasibility of employing smart optical fibre sensor (OFS andpiezoelectric impedance sensor made up of lead zirconate titanate (PZT forcomprehensive health monitoring of rocks, covering load history monitoring/retrieval aswell as damage assessment is presented in this paper. The rock specimens are subjected tocyclic loading and their conditions are continuously monitored using OFS and PZTsensors. OFS based multiplexed fibre Bragg grating (FBG sensors are surface bonded onthe rock specimens. Their strain sensing performance is compared with the conventionalelectric strain gauges (ESGs. In addition, PZT patches are also bonded on the specimensto study the damage pattern during different loading cycles. Unlike the FBGs or ESGs,PZT patches are used as bi-functional sensors and actuators, enabling them to be efficientdetectors of incipient damages using the principle of electromechanical impedance. Theexperimental study demonstrated superior performance of these smart FBG and PZTimpedance sensors. This work is expected to be useful for SHM based NDE application ofrock structures such as caverns and tunnels.

  5. Piezoelectric response of a PZT thin film to magnetic fields from permanent magnet and coil combination

    Science.gov (United States)

    Guiffard, B.; Seveno, R.

    2015-01-01

    In this study, we report the magnetically induced electric field E 3 in Pb(Zr0.57Ti0.43)O3 (PZT) thin films, when they are subjected to both dynamic magnetic induction (magnitude B ac at 45 kHz) and static magnetic induction ( B dc) generated by a coil and a single permanent magnet, respectively. It is found that highest sensitivity to B dc——is achieved for the thin film with largest effective electrode. This magnetoelectric (ME) effect is interpreted in terms of coupling between eddy current-induced Lorentz forces (stress) in the electrodes of PZT and piezoelectricity. Such coupling was evidenced by convenient modelling of experimental variations of electric field magnitude with both B ac and B dc induction magnitudes, providing imperfect open circuit condition was considered. Phase angle of E 3 versus B dc could also be modelled. At last, the results show that similar to multilayered piezoelectric-magnetostrictive composite film, a PZT thin film made with a simple manufacturing process can behave as a static or dynamic magnetic field sensor. In this latter case, a large ME voltage coefficient of under B dc = 0.3 T was found. All these results may provide promising low-cost magnetic energy harvesting applications with microsized systems.

  6. Measurement of effective piezoelectric coefficients of PZT thin films for energy harvesting application with interdigitated electrodes.

    Science.gov (United States)

    Chidambaram, Nachiappan; Mazzalai, Andrea; Muralt, Paul

    2012-08-01

    Interdigitated electrode (IDE) systems with lead zirconate titanate (PZT) thin films play an increasingly important role for two reasons: first, such a configuration generates higher voltages than parallel plate capacitor-type electrode (PPE) structures, and second, the application of an electric field leads to a compressive stress component in addition to the overall stress state, unlike a PPE structure, which results in tensile stress component. Because ceramics tend to crack at relatively moderate tensile stresses, this means that IDEs have a lower risk of cracking than PPEs. For these reasons, IDE systems are ideal for energy harvesting of vibration energy, and for actuators. Systematic investigations of PZT films with IDE systems have not yet been undertaken. In this work, we present results on the evaluation of the in-plane piezoelectric coefficients with IDE systems. Additionally, we also propose a simple and measurable figure of merit (FOM) to analyze and evaluate the relevant piezoelectric parameter for harvesting efficiency without the need to fabricate the energy harvesting device. Idealized effective coefficients e(IDE) and h(IDE) are derived, showing its composite nature with about one-third contribution of the transverse effect, and about two-thirds contribution of the longitudinal effect in the case of a PZT film deposited on a (100)-oriented silicon wafer with the in-plane electric field along one of the Si directions. Randomly oriented 1-μm-thick PZT 53/47 film deposited by a sol-gel technique, was evaluated and yielded an effective coefficient e(IDE) of 15 C·m(-2). Our FOM is the product between effective e and h coefficient representing twice the electrical energy density stored in the piezoelectric film per unit strain deformation (both for IDE and PPE systems). Assuming homogeneous fields between the fingers, and neglecting the contribution from below the electrode fingers, the FOM for IDE structures with larger electrode gap is derived to be

  7. A Piezoelectric PZT Ceramic Mulitlayer Stack for Energy Harvesting Under Dynamic Forces

    Science.gov (United States)

    Xu, Tian-Bing; Siochi, Emilie J.; Kang, Jin Ho; Zuo, Lei; Zhou, Wanlu; Tang, Xiudong; Jiang, Xiaoning

    2011-01-01

    Piezoelectric energy harvesting transducers (PEHTs) are commonly used in motion/vibration energy scavenging devices. To date, most researchers have focused on energy harvesting at narrow bandwidths around the mechanical resonance frequency, and most piezoelectric harvesting devices reported in the literature have very low effective piezoelectric coefficient (d(sub eff)) (ceramic multilayer stack (PZT-Stack) with high effective piezoelectric coefficient for high-performance PEHTs. The PZT-Stack is composed of 300 layers of 0.1 mm thick PZT plates, with overall dimensions of 32.4 mm X 7.0 mm X 7.0 mm. Experiments were carried out with dynamic forces in a broad bandwidth ranging from 0.5 Hz to 25 kHz. The measured results show that the effective piezoelectric coefficient of the PZT-stack is about 1 X 10(exp 5) pC/N at off-resonance frequencies and 1.39 X 10(exp 6) pC/N at resonance, which is order of magnitude larger than that of traditional PEHTs. The effective piezoelectric coefficients (d(sub eff)) do not change significantly with applied dynamic forces having root mean square (RMS) values ranging from 1 N to 40 N. In resonance mode, 231 mW of electrical power was harvested at 2479 Hz with a dynamic force of 11.6 N(sub rms), and 7.6 mW of electrical power was generated at a frequency of 2114 Hz with 1 N(sub rms) dynamic force. In off-resonance mode, an electrical power of 18.7 mW was obtained at 680 Hz with a 40 N(sub rms) dynamic force. A theoretical model of energy harvesting for the PZT-Stack is established. The modeled results matched well with experimental measurements. This study demonstrated that high effective piezoelectric coefficient structures enable PEHTs to harvest more electrical energy from mechanical vibrations or motions, suggesting an effective design for high-performance low-footprint PEHTs with potential applications in military, aerospace, and portable electronics. In addition, this study provides a route for using piezoelectric multilayer

  8. Design, Modeling and Optimization of a Piezoelectric Pressure Sensor based on a Thin-Film PZT Membrane Containing Nanocrystalline Powders

    Directory of Open Access Journals (Sweden)

    Vahid MOHAMMADI

    2009-11-01

    Full Text Available In this paper fabrication of a 0-3 ceramic/ceramic composite lead zirconate titanate, Pb(Zr0.52Ti0.48O3 thin film has been presented and then a pressure sensor based on multilayer thin-film PZT diaphragm contain of Lead Zirconate Titanate nanocrystalline powders was designed, modeled and optimized. Dynamics characteristics of this multilayer diaphragm have been investigated by ANSYS® FE software. By this simulation the effective parameters of the multilayer PZT diaphragm for improving the performance of a pressure sensor in different ranges of pressure are optimized. The optimized thickness ratio of PZT layer to SiO2 was given in the paper to obtain the maximum deflection of the multilayer thin-film PZT diaphragm. A 0-3 ceramic/ceramic composite lead zirconate titanate, Pb(Zr0.52Ti0.48O3 film has been developed to fabricate the pressure sensor by a hybrid sol gel process. PZT nanopowders fabricated via conventional sol gel method and uniformly dispersed in PZT precursor solution by an attrition mill. XRD analysis shows that perovskite structure would be formed due to the presence of a significant amount of ceramic nanopowders. This texture has a good effect on piezoelectric properties of perovskite structure. The film forms a strongly bonded network and less shrinkage occurs, so the films do not crack during process. Also the aspect ratio through this process would be increased. SEM micrographs indicated that PZT films were uniform, crack free and have a composite microstructure and a piezoelectric coefficient d31 of -40 pC.N-1 and d33 ranged from 50pm.N-1 to 60pm.N-1.

  9. Performance of PIN-PMN-PT Single Crystal Piezoelectric versus PZT8 Piezoceramic Materials in Ultrasonic Transducers

    Science.gov (United States)

    DeAngelis, D. A.; Schulze, G. W.

    The recent advancements in the manufacturing of single crystal PIN-PMN-PT piezoelectric materials now make them a cost-competitive alternative to PZT4 and PZT8 (Navy Types I and III) piezoceramic materials, which have been the workhorse of power ultrasonic applications (e.g., welding, cutting, sonar, etc.) for over 50 years. Although there are great benefits to the use of single crystal materials with respect to high output, as well as added actuating and sensing abilities, many transducer designers are still reluctant to explore these materials due to inadequate design guidelines for substituting the familiar PZT materials; for example, what are the implications of the higher capacitance, sensitivity to chipping/cracks, aging effects, frequency shifts, or how much preload can be used are all common questions. This research is a case study on the performance of identical ultrasonic transducer bodies, used for semiconductor wire bonding, assembled with either PZT8 or PIN-PMN-PT piezo material. The main purpose of the study is to establish rule-of-thumb design guidelines for direct substitution of single crystal materials in existing PZT8 transducer designs, along with a side-by-side performance comparison to highlight benefits. Several metrics are investigated such as impedance, frequency, displacement gain, quality factor and electromechanical coupling factor.

  10. Modeling of PZT-induced Lamb wave propagation in structures by using a novel two-layer spectral finite element

    Science.gov (United States)

    Liu, Xiaotong; Zhou, Li; Ouyang, Qinghua

    2016-04-01

    This paper presents a novel two-layer spectral finite element model, consisting of PZT wafer and host structure, to simulate PZT-induced Lamb wave propagation in beam-like and plate-like structures. Based on the idea of equal displacement on the interface between PZT wafer and host structure, the one-dimensional spectral beam element of PZT-host beam and two-dimensional spectral plate element of PZT-host plate are considered as one hybrid element, respectively. A novel approach is proposed by taking the coupling effect of piezoelectric transducers in the thickness direction into account. The dynamic equation of the two-layer spectral element is derived from Hamilton's principle. Validity of the developed spectral finite element is verified through numerical simulation. The result indicates that, compared with the conventional finite element method (FEM) based on elasticity, the proposed spectral finite element is proved to have a high accuracy in modeling Lamb wave propagation, meanwhile, significantly improve the calculation efficiency.

  11. Enhanced off-resonance magnetoelectric response in laser annealed PZT thick film grown on magnetostrictive amorphous metal substrate

    Energy Technology Data Exchange (ETDEWEB)

    Palneedi, Haribabu [Materials Interface Laboratory, Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of); Functional Ceramics Group, Korea Institute of Materials Science (KIMS), Changwon 641-831 (Korea, Republic of); Maurya, Deepam; Priya, Shashank [Bio-inspired Materials and Devices Laboratory (BMDL), Center for Energy Harvesting Materials and Systems (CEHMS), Virginia Tech, Blacksburg, Virginia 24061 (United States); Kim, Gi-Yeop; Choi, Si-Young, E-mail: youngchoi@kims.re.kr [Materials Modeling and Characterization Department, Korea Institute of Materials Science (KIMS), Changwon 641-831 (Korea, Republic of); Kang, Suk-Joong L. [Materials Interface Laboratory, Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701 (Korea, Republic of); Kim, Kwang-Ho [School of Materials Science and Engineering, Pusan National University, Busan 609-735 (Korea, Republic of); Ryu, Jungho, E-mail: jhryu@kims.re.kr [Functional Ceramics Group, Korea Institute of Materials Science (KIMS), Changwon 641-831 (Korea, Republic of)

    2015-07-06

    A highly dense, 4 μm-thick Pb(Zr,Ti)O{sub 3} (PZT) film is deposited on amorphous magnetostrictive Metglas foil (FeBSi) by granule spray in vacuum process at room temperature, followed by its localized annealing with a continuous-wave 560 nm ytterbium fiber laser radiation. This longer-wavelength laser radiation is able to anneal the whole of thick PZT film layer without any deteriorative effects, such as chemical reaction and/or atomic diffusion, at the interface and crystallization of amorphous Metglas substrate. Greatly enhanced dielectric and ferroelectric properties of the annealed PZT are attributed to its better crystallinity and grain growth induced by laser irradiation. As a result, a colossal off-resonance magnetoelectric (ME) voltage coefficient that is two orders of magnitude larger than previously reported output from PZT/Metglas film-composites is achieved. The present work addresses the problems involved in the fabrication of PZT/Metglas film-composites and opens up emerging possibilities in employing piezoelectric materials with low thermal budget substrates (suitable for integrated electronics) and designing laminate composites for ME based devices.

  12. Real time monitoring of spot-welded joints under service load using lead zirconate titanate (PZT) transducers

    Science.gov (United States)

    Yao, Ping; Zheng, Botong; Dawood, Mina; Huo, Linsheng; Song, Gangbing

    2017-03-01

    This paper proposes a nondestructive method to evaluate the health status of resistance spot-welded (RSW) joint under service load using lead zirconate titanate (PZT) active sensing system, in which the PZT transducers were used as both actuator and sensor. The physical principle of the approach was validated through a numerical analysis showing that an opening between the faying faces at the welded joint occurred under tension load. The opening decreased the contact area hence reduced the amplitude of the stress wave received by the PZT sensor. Therefore, by comparing the energy index of the signals before and after the loading, the health condition of the joint can be evaluated. Five ST14 steel single lap joint specimens were tested under tension load while being monitored by the PZT sensing system and digital image correlation (DIC) system in real time. The data obtained from the DIC system validated the numerical results. By comparing the energy index of the signal obtained from the PZT sensing system before and after unloading, it was concluded that the RSW joint was intact after being loaded to the service load. The proposed method is promising in evaluating the health condition of RSW joint nondestructively.

  13. Enhanced voltage-controlled magnetic anisotropy in magnetic tunnel junctions with an MgO/PZT/MgO tunnel barrier

    Science.gov (United States)

    Chien, Diana; Li, Xiang; Wong, Kin; Zurbuchen, Mark A.; Robbennolt, Shauna; Yu, Guoqiang; Tolbert, Sarah; Kioussis, Nicholas; Khalili Amiri, Pedram; Wang, Kang L.; Chang, Jane P.

    2016-03-01

    Compared with current-controlled magnetization switching in a perpendicular magnetic tunnel junction (MTJ), electric field- or voltage-induced magnetization switching reduces the writing energy of the memory cell, which also results in increased memory density. In this work, an ultra-thin PZT film with high dielectric constant was integrated into the tunneling oxide layer to enhance the voltage-controlled magnetic anisotropy (VCMA) effect. The growth of MTJ stacks with an MgO/PZT/MgO tunnel barrier was performed using a combination of sputtering and atomic layer deposition techniques. The fabricated MTJs with the MgO/PZT/MgO barrier demonstrate a VCMA coefficient, which is ˜40% higher (19.8 ± 1.3 fJ/V m) than the control sample MTJs with an MgO barrier (14.3 ± 2.7 fJ/V m). The MTJs with the MgO/PZT/MgO barrier also possess a sizeable tunneling magnetoresistance (TMR) of more than 50% at room temperature, comparable to the control MTJs with an MgO barrier. The TMR and enhanced VCMA effect demonstrated simultaneously in this work make the MgO/PZT/MgO barrier-based MTJs potential candidates for future voltage-controlled, ultralow-power, and high-density magnetic random access memory devices.

  14. Enhanced off-resonance magnetoelectric response in laser annealed PZT thick film grown on magnetostrictive amorphous metal substrate

    Science.gov (United States)

    Palneedi, Haribabu; Maurya, Deepam; Kim, Gi-Yeop; Priya, Shashank; Kang, Suk-Joong L.; Kim, Kwang-Ho; Choi, Si-Young; Ryu, Jungho

    2015-07-01

    A highly dense, 4 μm-thick Pb(Zr,Ti)O3 (PZT) film is deposited on amorphous magnetostrictive Metglas foil (FeBSi) by granule spray in vacuum process at room temperature, followed by its localized annealing with a continuous-wave 560 nm ytterbium fiber laser radiation. This longer-wavelength laser radiation is able to anneal the whole of thick PZT film layer without any deteriorative effects, such as chemical reaction and/or atomic diffusion, at the interface and crystallization of amorphous Metglas substrate. Greatly enhanced dielectric and ferroelectric properties of the annealed PZT are attributed to its better crystallinity and grain growth induced by laser irradiation. As a result, a colossal off-resonance magnetoelectric (ME) voltage coefficient that is two orders of magnitude larger than previously reported output from PZT/Metglas film-composites is achieved. The present work addresses the problems involved in the fabrication of PZT/Metglas film-composites and opens up emerging possibilities in employing piezoelectric materials with low thermal budget substrates (suitable for integrated electronics) and designing laminate composites for ME based devices.

  15. Study of the microstructure and the hardness of PZT piezoelectric ceramics types I and III used in electro acoustic transducers; Estudo da microestrutura e da microdureza das ceramicas piezoeletricas tipos PZT I e III utilizadas em transdutores eletroacusticos

    Energy Technology Data Exchange (ETDEWEB)

    Cabral, Ricardo de Freitas; Itaboray, Lucas Mendes; Santos, Anna Paula de Oliveira [Centro Universitario de Volta Redonda (UNIFOA), Volta Redonda, RJ (Brazil)

    2015-12-15

    The field of electronic processing of the ceramic piezoelectric type imported powdered led to the production of ceramics with 97% of theoretical density, homogeneous microstructure with great potential for applications in piezoelectric devices such as electro acoustic transducers. However, the production of electronic ceramics National piezoelectric type is not yet able to have as raw material zirconate titanate Lead (PZT) 100% made in Brazil. Thus, this is used for supply of domestic production, the zirconium oxide. In this work, both post PZT types I and III, imported, were uniaxially pressed at 70 MPa and sintered at 1200 and 1250 deg C for 3 hours. Hardness measurements were performed by micro indentation, X-ray diffraction analysis and Scanning Electron Microscopy. The hardness of PZT I was 393 HV. (author)

  16. Unexpected behavior of transient current in thin PZT films caused by grain-boundary conduction

    Science.gov (United States)

    Delimova, L. A.; Guschina, E. V.; Seregin, D. S.; Vorotilov, K. A.; Sigov, A. S.

    2017-06-01

    The behavior of the transient current at different preliminary polarizations has been studied in Pb(ZrTi)O3 (PZT) films with various grain structures. To affect the grain structure, PZT films were prepared by chemical solution deposition with a two-step crystallization process using combination of seed layers with a low Pb excess and the main layers with a 30 wt. % Pb excess. Some films were prepared with a fixed Pb excess in all the deposited layers. We found that the lead excess and the seed layer crystalline structure can affect the grain-boundary conduction which, in turn, influences the polarization dependence of the transient current and the appearance of current peaks which look like the so-called negative differential resistance region in the current-voltage curves. We show that the emergence of the current peaks in the PZT films depends on (i) whether the current flows inside the ferroelectric phase (grains) or outside, along grain boundaries and (ii) whether the applied bias direction is parallel or opposite to the polarization vector. A correlation between the grain-boundary conduction and current-polarization dependences is confirmed by the local current distribution measured by conductive atomic force microscopy. Possible mechanisms responsible for specific features of the transient current and appearance of the current peaks are discussed. The effect of grain-boundary conduction on the behavior of the current may be significant and should be taken into account in ferroelectric random access memory whose readout operation assumes registration of the magnitude of the polarization switching current under positive bias.

  17. Speed of sound estimation with active PZT element for thermal monitoring during ablation therapy: feasibility study

    Science.gov (United States)

    Kim, Younsu; Guo, Xiaoyu; Cheng, Alexis; Boctor, Emad M.

    2016-04-01

    Controlling the thermal dose during ablation therapy is instrumental to successfully removing the tumor while preserving the surrounding healthy tissue. In the practical scenario, surgeons must be able to determine the ablation completeness in the tumor region. Various methods have been proposed to monitor it, one of which uses ultrasound since it is a common intraoperative imaging modality due to its non-invasive, cost-effective, and convenient natures. In our approach, we propose to use time of flight (ToF) information to estimate speed of sound changes. Accurate speed of sound estimation is crucial because it is directly correlated with temperature change and subsequent determination of ablation completeness. We divide the region of interest in a circular fashion with a variable radius from the ablator tip. We introduce the concept of effective speed of sound in each of the sub-regions. Our active PZT element control system facilitates this unique approach by allowing us to acquire one-way ToF information between the PZT element and each of the ultrasound elements. We performed a simulation and an experiment to verify feasibility of this method. The simulation result showed that we could compute the effective speed of sound within 0.02m/s error in our discrete model. We also perform a sensitivity analysis for this model. Most of the experimental results had less than 1% error. Simulation using a Gaussian continuous model with multiple PZT elements is also demonstrated. We simulate the effect of the element location one the optimization result.

  18. Properties of PZT thick film made on LTCC substrates with dielectric intermediate layers

    Science.gov (United States)

    DÄ browski, Arkadiusz; Golonka, Leszek

    2016-11-01

    Results of experiments on application of various interlayers between LTCC (Low Temperature Cofired Ceramics) substrate and thick-film PZT (Lead Zirconate - Titanate) are described in this work. Thick-film intermediate layers were based on several dielectric materials: TiN, Al2O3, SiC, TiO2, SiC, YSZ, BN. Seven screen printable pastes were prepared on the base of powders of mentioned materials with addition of glass and organic vehicle. The substrates were made of 951 (DuPont), CeramTapeGC (CeramTec) and HL2000 (Heraeus) LTCC tapes. Sandwich type transducers, consisting of barrier layer, gold bottom electrode, PZT layer and silver top electrode were prepared and characterized. Basic piezoelectric parameters - permittivity, effective charge constant (d33(eff)) and remanent polarization were determined. The best properties were obtained for substrates made of 951. In general, interlayers based on TiO2, SiC and Al2O3 improved permittivity and charge constant comparing to bare substrates. For example, for 951 substrate the PZT layer exhibited d33(eff) equal to 160, 215, 250 and 230 pC/N for bare substrate, TiO2 interlayer, SiC interlayer and Al2O3 interlayer, respectively. In case of CeramTape GC substrates determined permittivity was equal to 215, 245, 235 and 275 for bare substrate, TiO2 interlayer, SiC interlayer and Al2O3 interlayer, respectively. In case of TiN and BN materials the parameters were considerably deteriorated.

  19. Polar-axis-oriented crystal growth of tetragonal PZT films on stainless steel substrate using pseudo-perovskite nanosheet buffer layer

    Directory of Open Access Journals (Sweden)

    Yoshiki Minemura

    2015-07-01

    Full Text Available Lead zirconate titanate (PZT film with polar axis orientation was grown on a SUS 316L stainless steel substrate with the help of a Ca2Nb3O10 nanosheet (ns-CN layer that had a pseudo-perovskite-type crystal structure. The ns-CN buffer layer was supported on a platinized SUS 316L (Pt/SUS substrate, followed by chemical solution deposition (CSD of the PZT films with tetragonal symmetry (Zr/Ti =40/60. The PZT films consisting of c-domain, with [001]-axis orientation of the perovskite unit cell, were deposited on the ns-CN/Pt/SUS substrate owing to (i epitaxial lattice matching between the unit cell of PZT and substrate surface and (ii in-plane thermal stress applied to the PZT film during cooling-down step of CSD procedure. The c-domain-oriented PZT film on ns-CN/Pt/SUS substrate exhibited enhanced remanent polarization of approximately 52 μC/cm2 and lowered dielectric permittivity of approximately 230, which are superior to those of conventional PZT films with random crystal orientation and comparable to those of epitaxial PZT films grown on (100SrRuO3//(100SrTiO3 substrates.

  20. Ferroelectric switching of band alignments in LSMO/PZT/Co multiferroic tunnel junctions: an ab initio study

    Science.gov (United States)

    Imam, M.; Stojić, N.; Binggeli, N.

    2017-08-01

    Band alignments in ferroelectric tunnel junctions (FTJs) are expected to play a critical role in determining the charge transport across the tunneling barrier. In general, however, the interface band discontinuities and their polarization dependence are not well known in these systems. Using a first-principles density-functional-theory approach, we explore the ferroelectric (FE) polarization dependence of the band alignments in {{La}}0.7{{Sr}}0.3{{MnO}}3/{{PbZr}}0.2{{Ti}}0.8{{{O}}}3/{Co} (LSMO/PZT/Co) multiferroic tunnel junctions, for which recent experiments indicated an ON/OFF conductivity behavior upon switching the PZT FE polarization. Our results on the pseudomorphic defect-free LSMO/PZT/Co FTJs evidence a major FE switching effect on the band discontinuities at both interfaces. Based on the changes in the band alignments, we provide a possible explanation for the observed trends in the resistive switching.

  1. Mechanical and dielectric characterization of lead zirconate titanate(PZT)/polyurethane(PU) thin film composite for energy harvesting

    Science.gov (United States)

    Aboubakr, S.; Rguiti, M.; Hajjaji, A.; Eddiai, A.; Courtois, C.; d'Astorg, S.

    2014-04-01

    The Lead Zirconate titanate (PZT) ceramic is known by its piezoelectric feature, but also by its stiffness, the use of a composite based on a polyurethane (PU) matrix charged by a piezoelectric material, enable to generate a large deformation of the material, therefore harvesting more energy. This new material will provide a competitive alternative and low cost manufacturing technology of autonomous systems (smart clothes, car seat, boat sail, flag ...). A thin film of the PZT/PU composite was prepared using up to 80 vol. % of ceramic. Due to the dielectric nature of the PZT, inclusions of this one in a PU matrix raises the permittivity of the composite, on other hand this latter seems to decline at high frequencies.

  2. Highly polarized single-c-domain single-crystal Pb(Mn,Nb)O(3)-PZT thin films.

    Science.gov (United States)

    Wasa, Kiyotaka; Adachi, Hideaki; Nishida, Ken; Yamamoto, Takashi; Matsushima, Tomoaki; Kanno, Isaku; Kotera, Hidetoshi

    2012-01-01

    In-plane unstrained single-c-domain/single-crystal thin films of PZT-based ternary ferroelectric perovskite, ξPb(Mn,Nb)O3-(1 - ξ)PZT, were grown on SrRuO(3)/Pt/MgO substrates using magnetron sputtering followed by quenching. The sputtered unstrained thin films exhibit unique ferroelectric properties: high coercive field, Ec > 180 kV/cm, large remanent polarization, P(r) = 100 μC/cm(2), small relative dielectric constants, ε* = 100 to 150, high Curie temperature, Tc = ~600 °C, and bulk-like large transverse piezoelectric constants, e31,f = -12.0 C/m(2) for PZT(48/52) at ξ = 0.06. The unstrained thin films are an ideal structure to extract the bulk ferroelectric properties. Their micro-structures and ferroelectric properties are discussed in relation to the potential applications for piezoelectric MEMS. © 2012 IEEE

  3. Structural and Electrical Properties of PZT/PVDF Piezoelectric Nanocomposites Prepared by Cold-Press and Hot-Press Routes

    Institute of Scientific and Technical Information of China (English)

    ZHANG De-Qing; WANG Da-Wei; YUAN Jie; ZHAO Quan-Liang; WANG Zhi-Ying; CAO Mao-Sheng

    2008-01-01

    @@ The 0-3 PZT/PVDF piezoelectric composites are prepared separately by hot-press and cold-press processes. The effects of the PZT content and the shaping-process on the composites are studied. The experimental results indicate that composites with 70% PZT nanopowders prepared by the hot-press method exhibit excellent piezo-electric and dielectric properties. The maxima of daa and e of the composites prepared by hot-press method are about 30% and 65% higher than those prepared by the cold-press method, respectively. This is mainly attributed to the favourable coupling of the two materials in the process of the hot press and the formation of the β-type PVDF, which possesses better electric properties.

  4. In situ X-ray diffraction based investigation of crystallization in solution deposited PZT thin films

    Science.gov (United States)

    Nittala, Krishna

    Solution deposited PZT based thin films have potential applications in embedded decoupling capacitors and pulse discharge capacitors. During solution deposition, precursor solution is deposited onto a substrate to obtain an amorphous film. The film is then crystallized by heating it at a high temperature (˜600 - 700°C). Conditions during the crystallization anneal such as precursor stoichiometry in solution, heating rate and adhesion layer in the substrate are known to influence phase and texture evolution in these films. However, a mechanistic understanding of the changes taking place in these thin films during crystallization is lacking. A better understanding of the crystallization processes in these thin films could enable tailoring the properties of thin films to suit specific applications. To explore the crystallization process in solution deposited PZT thin films, high temperature in situ laboratory and synchrotron X-ray diffraction based techniques were developed. Taking advantage of the high X-ray flux available at synchrotron facilities such as beamline 6-ID-B, Advanced Photon Source, Argonne National Laboratory, crystalline phases formed in the thin films during crystallization at the high heating rates (0.5 -- 60°C/s) typically used during film processing could be measured. Using a 2-D detector for these measurements allowed the simultaneous measurement of both phase and texture information during crystallization. Analytical treatment of the unconventional diffraction geometry used during the synchrotron based measurements was performed to develop methodologies for quantitative estimation of texture components. The nominal lead content in the starting solutions and the heating rate used during crystallization was observed to influence the sequence of phases formed during crystallization of the films. In films crystallized at fast heating rates, titanium segregation, probably due to diffusion of titanium from the adhesion layer, was observed. To

  5. Extrinsic coefficient charcterisation of PZT ceramics near the morphotropic phase boundary

    Directory of Open Access Journals (Sweden)

    Albareda, A.

    2006-06-01

    Full Text Available PZT ceramics with high piezoelectric coefficients have high extrinsic contributions. This extrinsic behaviour, which is related to the domain wall movement, produces high non-linear effects that are sometimes inconvenient, for example when it increases the losses in power devices. The relation between extrinsic behaviour and non-linearities could be used to provide a good extrinsic characterization of materials in order to optimise the piezoelectric devices. In all cases the physical explanation of the behaviour is sought. The aim of this work is to study the dependence of the linear and non-linear dielectric, piezoelectric and mechanical coefficients on the Ti fraction in PZT ceramic compositions near the morphotropic phase boundary (MPB. The dependence of these coefficients on the defect concentration is also analysed. Hard ceramics belonging to Ferroperm Piezoceramics, with two different acceptor dopant levels, high and low, have been measured.

    Las cerámicas PZT con coeficientes piezoeléctricos elevados poseen contribuciones extrínsecas grandes. Este comportamiento extrínseco, relacionado con el movimiento de las paredes de los dominios, comporta efectos no lineales grandes que no siempre son deseables, por ejemplo, al incrementar las pérdidas de los dispositivos piezoeléctricos. Esta correspondencia entre efectos extrínsecos y no linealidades puede ser utilizada para caracterizar las cerámicas con el fin de optimizar sus propiedades piezoeléctricas. En todos los casos se busca una interpretación física de los resultados obtenidos. El objetivo de este trabajo es el estudio de la dependencia de los coeficientes lineales y no lineales dieléctricos, piezoeléctricos y elásticos con la fracción de Ti en cerámicas PZT con composiciones de Zr-Ti cerca de la transición de fase morfotrópica (MPB. También se analiza la dependencia de estos coeficientes con la concentración de impurezas, utilizando para ello cerámicas de

  6. Processing effects for integrated PZT: Residual stress, thickness, and dielectric properties

    Science.gov (United States)

    Ong, Ryan Jason

    This dissertation focuses on the integration of lead zirconate titanate (PZT) films on Pt/Ti/SiO2//Si, and the effect of on properties. Direct deposition of PZT on Si will lead to on-chip power capacitors, non-volatile memory cells, and vibration sensors. However, previous research indicates that the dielectric, ferroelectric and piezoelectric response characteristics for the devices are often inferior to bulk specimens. Property variations have been attributed to changes in several major variables including, chemical composition, phase content, grain size, crystallographic orientation, film thickness, and stress, each of which, in turn, can depend on processing. The first goal of this work was to design a sol-gel processing methodology to control all major variables except film thickness and stress, thus isolating their respective effects on properties. All specimens were verified to be of the Pb(Zr0.53Ti0.47)O3 composition, in the perovskite structure, with a constant grain size of 110nm, and with (111) fiber texture. PZT film thickness was varied from 95nm to 500nm and residual stress was measured to be either 150 or 180MPa, biaxial tensile, depending on thickness. These specimens allowed for new insights into the fundamental differences between bulk materials and thin films. A series-capacitor model accounted for the observed dilution in room-temperature K from >900 to ˜600 as film thickness decreased, but could not account for the absence of the expected dielectric anomaly at high temperatures. Instead, a stress-induced distributed phase transformation related to the polycrystalline nature of the film was proposed to account for the observed behavior. Residual stress reduced the spontaneous polarization values in these specimens to 32muC/cm 2 from the predicted stress-free value of 50muC/cm2. An increase in coercive field was attributed to interfacial capacitance and residual stress, whereas a decrease of 30MPa tensile stress resulted in an increase of d33

  7. Monte Carlo Simulation Study of Diffuse Scattering in PZT, Pb(Zr,Ti)O3

    Science.gov (United States)

    Welberry, T. R.; Goossens, D. J.; Withers, R. L.; Baba-Kishi, K. Z.

    2010-05-01

    Transverse polarized diffuse streaks have been observed in diffraction patterns of Pb(Zr1- x Ti x )O3 (PZT) ceramics for compositions ranging from x = 0.3 (rhombohedral phase) to x = 0.7 (tetragonal phase) including the important morphotropic phase boundary (MPB) region ( x = 0.48). The streaks correspond to diffuse planes of scattering in three dimensions, and these are oriented normal to the (cubic) piezo-electric properties of the material, but its presence requires the currently accepted models for the average structure to be reassessed.

  8. Luminescence of Eu{sup 3+} incorporated into PZT tetragonal ceramics prepared by sol-gel

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, Federico; Schabes-Retchkiman, Pablo; GarcIa-Macedo, Jorge [Instituto de FIsica, Universidad Nacional Autonoma de Mexico, A.P. 20-364, 01000 Mexico, D.F. (Mexico)

    2004-09-07

    Luminescence of Eu{sup 3+} in Pb(Zr{sub x}Ti{sub 1-x})O{sub 3} (PZT) polycrystalline tetragonal samples synthesized by sol-gel processing is reported. Studies by x-ray diffraction, energy dispersive spectroscopy and high resolution transmission electron microscopy demonstrate the incorporation of the dopant in the host. A broad charge transfer band centred around 266 nm was observed in the Eu{sup 3+} excitation spectra. Eu{sup 3+} is in a low symmetry site. Luminescence was lost between 673 and 1173 K. It was recovered after 1 h of heat treatment at 1273 K, when nanocrystallites were formed.

  9. Effect of sol temperature on structural, morphological and magnetic properties of PZT thin films on alumina substrate

    Science.gov (United States)

    Sreelalitha, K.; Thyagarajan, K.

    2016-01-01

    In the present study, we investigate the structural, morphological and magnetic properties of sol-gel spin-coated PZT thin films on alumina substrate. The morphotropic phase boundary (MPB) of PZT [Pb (Zr1-xTix)03] between the tetragonal and rhombohedral phases occurs at the Zr/Ti ratio of 52/48. At the MPB the physical properties of PZT are of far-reaching importance due to their possible crystalline phases. In this study Pb(Zr0.52Ti0.48)03 sols are prepared at room temperature and at 125 °C. The gels are coated onto alumina substrate using a spin-coating unit as two and three layers. The structural studies using XRD confirm the perovskite phase formation at an annealing temperature of 660 °C for both films. The structural parameter grain size, dislocation density, lattice parameters and strain were dependent on the sol temperature. The SEM morphology of the samples represents well-developed dense grain structure and thickness in micrometer ranges. The VSM analysis shows diamagnetic and ferromagnetic hysteresis loop. The ferromagnetism at low fields in PZT films is confirmed by studying the magnetic properties of powder made of the same gel. The effect of heat treatment on the gel preparation is observed on structural, morphological and magnetic properties of PZT thin films. The ferromagnetism in PZT can be attributed to oxygen vacancies. The squareness ratio of the films shows the application of the films as a high-density recording medium.

  10. The effects of dimensional parameters on sensing and energy harvesting of an embedded PZT in a total knee replacement

    Science.gov (United States)

    Safaei, Mohsen; Anton, Steven R.

    2016-04-01

    Total Knee Replacement (TKR), one of the most common surgeries in the United States, is performed when the patient is experiencing significant amounts of pain or when knee functionality has become substantially degraded. Despite impressive recent developments, only about 85% of patients are satisfied with the pain reduction after one year. Therefore, structural health and performance monitoring are integral for intraoperative and postoperative feedback. In extension of the author's previous work, a new configuration for implementation of piezoelectric transducers in total knee replacement bearings is proposed and FEA modeling is performed to attain appropriate sensing and energy harvesting ability. The predicted force transmission ratio to the PZT (ratio of force applied to the bearing to force transferred to the embedded piezoelectric transducer) is about 6.2% compared to about 5% found for the previous encapsulated design. Dimensional parameters of the polyethylene bearing including the diameter and depth of the PZT pocket as well as the placement geometry of the PZT transducer within the bearing are hypothesized as the most influential parameters on the performance of the designed system. The results show a small change of 1% and 2.3% in the output of the system as a result of variation in the PZT location and pocket diameter, respectively. Whereas, the output of the system is significantly sensitive to the pocket depth; a pocket 0.01 mm deeper than the PZT transducer leads to no force transmission, and a pocket 0.15 mm shallower leads to full load transmission to the PZT. In order to develop a self-powered sensor, the amount of energy harvested from tibial forces for the proposed geometry is investigated.

  11. Formación de fases en materiales cerámicos PZT dopados con fósforo

    OpenAIRE

    2001-01-01

    [ES] La modificación superficial de materiales cerámicos titanato circonato de plomo (PZT) con ester fosfato deja un residuo de cationes de fósforo adsorbidos en la superficie de las partículas de este polvo. Durante el proceso de sinterización, esta capa superficial reacciona con el material PZT para formar compuestos ricos en plomo, como el Pb3(PO4)2 y el Pb4(P2O9). La formación de estos compuestos está en el origen de la inhibición del crecimiento de grano observada en materiales ...

  12. Microestructura y propiedades de materiales cerámicos PZT con control de crecimiento de grano

    Directory of Open Access Journals (Sweden)

    Celi, L. A.

    1999-10-01

    Full Text Available Lead zirconate titanate ceramic powders have been surface modified by using phosphor esther 0.3% in volume. The phosphorous modification gave higher densities at lower temperatures associated with a reduction of the weight losses during the densification process. From the relationships between ceramic processing and microstructure, it was established that the phosphorous surface modification allows the effective grain growth control as well a higher homogeneity in the grain size distribution.

    Se ha realizado un proceso de modificación superficial con ester fosfato al 0.3% en volumen, sobre polvo cerámico de titanato circonato de plomo, PZT. Se observa que el material modificado con fósforo presenta una mayor densificación aparente a una temperatura menor unida a una reducción de las pérdidas de peso durante el proceso de densificación. Se han establecido las relaciones entre el procesamiento y las microestructuras del material PZT sin modificar y el modificado. Se evidencia un control del crecimiento de grano y una mayor homogeneidad en la distribución de tamaños de grano en el material modificado.

  13. Ferroelectric–Ferromagnetic Composites Based on PZT Type Powder and Ferrite Powder

    Directory of Open Access Journals (Sweden)

    Bochenek D.

    2013-12-01

    Full Text Available W pracy otrzymano ferroelektryczno-ferromagnetyczne kompozyty na bazie ceramicznego proszku typu PZT. Połączenie ferroelektrycznego i magnetycznego proszku miało na celu otrzymanie materiałów wykazujących zarówno elektryczne i magne- tyczne właściwości. Ferroelektryczny, ceramiczny proszek (w ilości 90% stanowiły domieszkowane składy proszku typu PZT, natomiast magnetycznym składnikiem w kompozycie był niklówo-cynkowy ferryt (Nii-^Zn^Fe^Oj. Syntetyzowanie składni- ków kompozytu ceramiczno-ferrytowego przeprowadzono metodą spiekania wy prasek w fazie stałej, natomiast zagęszczanie zsyntetyzowanego kompozytowego proszku metodą spiekania swobodnego. Przeprowadzono badania rentgenowskie, mikrostrukturalne. EDS. dielektryczne, magnetyczne, tarcia wewnętrznego oraz elektrycznej pętli hi sterczy. Badania wykazały, występowanie korclacji między podukładem magnetycznym i podukładem elektrycznym w ferroelektryczno-ferromagnetycznych kompozytach. Dzięki ferroelektrycznym i magnetycznym właściwościom otrzymanych kompozytów, materiały tego typu mogą znaleźć zastosowanie aplikacyjne w nowych typach pamięci.

  14. A comparative approach to predicting effective dielectric, piezoelectric and elastic properties of PZT/PVDF composites

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Zeeshan [University Department of Physics, T.M. Bhagalpur University, Bhagalpur 812007 (India); Prasad, Ashutosh, E-mail: apd.phy@gmail.co [University Department of Physics, T.M. Bhagalpur University, Bhagalpur 812007 (India); Prasad, K., E-mail: k.prasad65@gmail.co [University Department of Physics, T.M. Bhagalpur University, Bhagalpur 812007 (India)

    2009-11-01

    The present study addresses the problem of quantitative prediction of effective relative permittivity, dielectric loss factor, piezoelectric charge coefficient, and Young's modulus of PZT/PVDF diphasic ceramic-polymer composite as a function of volume fraction of PZT in the different compositions. Theoretical results for effective relative permittivity derived from several dielectric mixture equations like those of Knott, Rother-Lichtenecker, Bruggeman, Maxwell-Wagner-Webmann-Skipetrov or Dias-Dasgupta, Furukawa, Lewin, Wiener, Jayasundere-Smith, Modified Cule-Torquato, Taylor, Poon-Shin and Rao et al. were fitted to the experimental data taken from previous works of Yamada et al. Similarly, the results for effective piezoelectric coefficient and Young's modulus, derived from different appropriate equations were fitted to the corresponding experimental data taken from the literature. The study revealed that only a few equations like modified Rother-Lichtenecker equation, Dias-Dasgupta equation and Rao equation for dielectric and piezoelectric properties while the four new equations developed in the present study of elastic property (Young's modulus) well fitted the corresponding experimental results. Further, the acceptable data put to various regression analyses showed that in most of the cases the third order polynomial regression analysis provided more acceptable fits.

  15. A nonlinear model for magnetocapacitance effect in PZT-ring/Terfenol-D-strip magnetoelectric composites

    Science.gov (United States)

    Zhang, Juanjuan; Wen, Jianbiao; Gao, Yuanwen

    2016-06-01

    In previous works, most of them employ a linear constitutive model to describe magnetocapacitance (MC) effect in magnetoelectric (ME) composites, which lead to deficiency in their theoretical results. In view of this, based on a nonlinear magnetostrictive constitutive relation and a linear piezoelectric constitutive relation, we establish a nonlinear model for MC effect in PZT-ring/Terfenol-D-strip ME composites. The numerical results in this paper coincide better with experimental data than that of a linear model, thus, it's essential to utilize a nonlinear constitutive model for predicting MC effect in ME composites. Then the influences of external magnetic fields, pre-stresses, frequencies, and geometric sizes on the MC effect are discussed, respectively. The results show that the external magnetic field is responsible for the resonance frequency shift. And the resonance frequency is sensitive to the ratio of outer and inner radius of the PZT ring. Moreover, some other piezoelectric materials are employed in this model and the corresponding MC effects are calculated, and we find that different type of piezoelectric materials affect the MC effect obviously. The proposed model is more accurate for multifunction devices designing.

  16. Numerical analysis for structural health monitoring of a damaged composite panel using PZT actuators and sensors

    Science.gov (United States)

    Nagabhushana, A.; Spiegel, M.; Adu, S.; Hayes, N.; Paul, D.; Trivedi, K.; Fairbee, B.; Zheng, H.; Gerrity, A.; Kotru, S.; Roy, S.; Barkey, M.; Burkett, S. L.

    2012-04-01

    Reliable damage detection is crucial for assessing the integrity of a structure. In this paper, a numerical study of a composite panel fabricated to simulate a crack is undertaken using finite element methods (FEM). The damage to be considered is a transverse crack which pre-exists in the structure. The finite element models are developed for an undamaged and a damaged composite panel to compute the change in Lamb wave response due to the existence of a crack. The model is validated using shear lag analysis applied at the crack. The results are verified experimentally by comparing the results for an undamaged composite panel and a composite panel fabricated with a simulated crack using the vacuum assisted resin transfer molding (VARTM) process. The responses for each panel are obtained using surface mounted lead zirconate titanate (PZT) actuators and sensors. PZT is used to generate Lamb waves which produce stress throughout the panel thickness. Propagation characteristics of Lamb waves are varied by the presence of damage. The sensor data provide reliable information about the integrity of the structure. Numerical results are compared to the sensor output to ensure accuracy of the damage detection system.

  17. No linealidad en muestras cerámicas de PZT muy delgadas

    Directory of Open Access Journals (Sweden)

    de Frutos, J.

    1999-10-01

    Full Text Available The development of piezoelectric sensors for high frequency requires to work with very thin samples of material. At this thick nesses, the stress concentration produces strong perturbations in the materials, and the origin oF a non linear response, which depends field on working conditions. With the goal to advance in the knowledgement of this phenomenon, and by using Complex Impedance Spectroscopy, we have analysed the response of PZT ceramics with thickness of microns as a function of the applied and the amplitude of the analysis signal. These results allow to establish the base to the development of ultrasonic tunable sensors for high frequency.

    El desarrollo de sensores piezoeléctricos de alta frecuencia, exige trabajar con muestras de material muy delgadas, del orden de micras. En estos espesores, las tensiones de trabajo causan fuertes perturbaciones en los materiales, provocando respuestas no lineales, sumamente dependientes de las condiciones de trabajo. Con el objetivo de avanzar en el conocimiento de este fenómeno, y haciendo uso de la técnica de Espectroscopia de Impedancia Compleja, hemos analizado la respuesta de muestras de PZT cerámico adelgazadas a espesores de micras, en función del campo aplicado y de la amplitud de la señal de análisis. El estudio de estos resultados, puede permitir sentar las bases para el desarrollo de sensores ultrasónicos de alta frecuencia sintonizables.

  18. Powering low-power implants using PZT transducer discs operated in the radial mode

    Science.gov (United States)

    Sanni, Ayodele; Vilches, Antonio

    2013-11-01

    This paper reports experimental results that are used to compare operation characteristics of lead zirconate titanate (PZT) piezoelectric ceramic discs operated in the radial mode. The devices are driven to radially vibrate at their lowest fundamental resonant frequency and thus transmit and receive power when immersed in a liquid phantom. A number of 1 mm × 10 mm (thickness × diameter) PZT discs are characterized experimentally within a propagation tank and results discussed. On the basis of these measured characteristics, a novel application is developed and reported for the first time. This consists of a tuned LC resonator circuit which is used at the receiving disc to maximize sensitivity as well as a Seiko start-up IC S-882Z which is employed to charge a capacitor that drives a PIC microcontroller (μC) once the voltage exceeds 2 V DC. We show that a mean input power of 486 mW RMS results in 976 μW RMS received over a range of 80 mm and that this is sufficient to periodically (every 60 s) power the μC to directly drive a red LED for 5 ms with a current of 4.8 mA/flash. This approach is suitable for low-power, periodically activated analogue bio-implant applications.

  19. Deposition of highly (111)-oriented PZT thin films by using metal organic chemical deposition

    CERN Document Server

    Bu, K H; Choi, D K; Seong, W K; Kim, J D

    1999-01-01

    Lead zirconate titanate (PZT) thin films have been grown on Pt/Ta/SiNx/Si substrates by using metal organic chemical vapor deposition with Pb(C sub 2 H sub 5) sub 4 , Zr(O-t-C sub 4 H sub 9) sub 4 , and Ti(O-i-C sub 3 H sub 7) sub 4 as source materials and O sub 2 as an oxidizing gas. The Zr fraction in the thin films was controlled by varying the flow rate of the Zr source material. The crystal structure and the electrical properties were investigated as functions of the composition. X-ray diffraction analysis showed that at a certain range of Zr fraction, highly (111)-oriented PZT thin films with no pyrochlore phases were deposited. On the other hand, at low Zr fractions, there were peaks from Pb-oxide phases. At high Zr fractions, peaks from pyrochlore phase were seen. The films also showed good electrical properties, such as a high dielectric constant of more than 1200 and a low coercive voltage of 1.35 V.

  20. Design Considerations for Aural Vital Signs Using PZT Piezoelectric Ceramics Sensor Based on the Computerization Method

    Directory of Open Access Journals (Sweden)

    Jerapong Tantrakoon

    2007-11-01

    Full Text Available The purpose was to illustrate how system developed for measurement of the aural vital signs such as patient’s heart and lung sounds in the hospital. For heart sounds measurement must operate the frequency response between 20 – 800 Hz, and lung sounds measurement must operate the frequency response between 160 – 4,000 Hz. The method was designed PZT piezoelectric ceramics for both frequency response in the same PZT sensor. It converts a signal from aural vital sign form to voltage signal. The signal is suitably amplified and re-filtered in band pass frequency band. It is converted to digital signal by an analog to digital conversion circuitry developed for the purpose. The results were that all signals can fed to personal computer through the sound card port. With the supporting software for drawing of graphic on the screen, the signal for a specific duration is accessed and stored in the computer’s memory in term of each patient’s data. In conclusion, the data of each patient call dot pcg (.pcg for drawing graph and dot wave (.wave for sound listening or automatic sending via electronic mail to the physician for later analysis of interpreting the sounds on the basis of their time domain and frequency domain representation to diagnose heart disorders.

  1. Polarization-dependent interfacial coupling modulation of ferroelectric photovoltaic effect in PZT-ZnO heterostructures.

    Science.gov (United States)

    Pan, Dan-Feng; Bi, Gui-Feng; Chen, Guang-Yi; Zhang, Hao; Liu, Jun-Ming; Wang, Guang-Hou; Wan, Jian-Guo

    2016-03-08

    Recently, ferroelectric perovskite oxides have drawn much attention due to potential applications in the field of solar energy conversion. However, the power conversion efficiency of ferroelectric photovoltaic effect currently reported is far below the expectable value. One of the crucial problems lies in the two back-to-back Schottky barriers, which are formed at the ferroelectric-electrode interfaces and blocking most of photo-generated carriers to reach the outside circuit. Herein, we develop a new approach to enhance the ferroelectric photovoltaic effect by introducing the polarization-dependent interfacial coupling effect. Through inserting a semiconductor ZnO layer with spontaneous polarization into the ferroelectric ITO/PZT/Au film, a p-n junction with strong polarization-dependent interfacial coupling effect is formed. The power conversion efficiency of the heterostructure is improved by nearly two orders of magnitude and the polarization modulation ratio is increased about four times. It is demonstrated that the polarization-dependent interfacial coupling effect can give rise to a great change in band structure of the heterostructure, not only producing an aligned internal electric field but also tuning both depletion layer width and potential barrier height at PZT-ZnO interface. This work provides an efficient way in developing highly efficient ferroelectric-based solar cells and novel optoelectronic memory devices.

  2. Reliability of vibration energy harvesters of metal-based PZT thin films

    Science.gov (United States)

    Tsujiura, Y.; Suwa, E.; Kurokawa, F.; Hida, H.; Kanno, I.

    2014-11-01

    This paper describes the reliability of piezoelectric vibration energy harvesters (PVEHs) of Pb(Zr,Ti)O3 (PZT) thin films on metal foil cantilevers. The PZT thin films were directly deposited onto the Pt-coated stainless-steel (SS430) cantilevers by rf-magnetron sputtering, and we observed their aging behavior of power generation characteristics under the resonance vibration condition for three days. During the aging measurement, there was neither fatigue failure nor degradation of dielectric properties in our PVEHs (length: 13 mm, width: 5.0 mm, thickness: 104 μm) even under a large excitation acceleration of 25 m/s2. However, we observed clear degradation of the generated electric voltage depending on excitation acceleration. The decay rate of the output voltage was 5% from the start of the measurement at 25 m/s2. The transverse piezoelectric coefficient (e31,f) also degraded with almost the same decay rate as that of the output voltage; this indicates that the degradation of output voltage was mainly caused by that of piezoelectric properties. From the decay curves, the output powers are estimated to degrade 7% at 15 m/s2 and 36% at 25 m/s2 if we continue to excite the PVEHs for 30 years.

  3. ELABORATION AND DIELECTRIC CHARACTERIZATION OF A DOPED FERROELECTRIC MATERIAL TYPE PZT

    Directory of Open Access Journals (Sweden)

    M. Abba

    2015-07-01

    Full Text Available The main objective of this work is based on the synthesis and dielectric characterization of a new material in ceramic PZT with a perovskite structure ABO3. We are interested to study the Quaternary system (doping in site A and site B of general formula: Pb0.96Ba0.02Ca0.02[(Zr0.52Ti0.480.94(Zn1/3Ta2/30.03(In1/3Sb2/30.03]O3 short PZT-PBC-ZTIS. The sample selected for this study was prepared by the method of synthesis with solid way. Heat treatment was applied to these compositions at different temperatures: 1100, 1150,1180 and 1200 °C successively to optimize the sintering temperature optimal where the density of the sample is maximum (near theoretical density and therefore the product has better physical quality. The study of dielectric properties of all samples showed a high permittivity dielectric εr = 18018, low dielectric loss: tgδ = 7.62%, for the composition sintered to 1180 ° C included in the phase morphotropique zone (FMP.

  4. Investigation of Co-doped PZT films deposited by rf-magnetron sputtering

    Directory of Open Access Journals (Sweden)

    Felicia Gheorghiu

    2014-09-01

    Full Text Available The focus of the present paper is to describe the preparation procedure and to investigate the microstructural characteristics and the electrical properties of Co-doped PZT films deposited by rf-sputtering by using a “mixture” target system onto Au-electroded Al2O3 ceramic substrates. The X-ray diffraction patterns of the Co-doped PZT thin films as a function of the annealing temperature confirmed the formation of pure perovskite phase started with temperatures of 600 °C, but a perfect crystallization was achieved at a temperature of ∼700 °C. The microstructures strongly depend on the thermal treatment temperature and indicated a discontinuous surface without large pores and with a bimodal grain size distribution. The XPS analysis demonstrated that the dopant element is present mainly in its Co2+ state. The macroscopic P(E hysteresis loops were recorded in different locations of the films surface and demonstrated ferroelectric behaviour with a resistive leakage contribution.

  5. Study on delayed cracking of conductive notch under electric field in PZT-5H ferroelectric ceramics

    Institute of Scientific and Technical Information of China (English)

    QIAO Guangli; SU Yanjing; QIAO Lijie; CHU Wuyang

    2006-01-01

    Electric-field-induced delay cracking of conducting notch in PZT-5H ferroelectric ceramics has been studied using a compact specimen with a notch filled in conductive silver paste. The critical electric field that induces instant failure of the PZT-5H specimen is shown to be EF = 14.7(3.2 kV/cm. When an electric field lower than EF, but higher than EDF = 9.9 kV/cm was applied, a micro-crack formed at the conductive notch tip instantly, propagating slowly until the specimen failure. When the electric field was lower than EDF, the micro-crack propagated a short distance, and then stopped. When the electric field was lower than EK=4.9 kV/cm, no cracks formed at the conductive notch tip instantly, however, a delay micro-crack would form and propagate. When the electric field was lower than EDK=2.4 kV/cm, no cracks formed and delay propagation occurred. A model for electric charge emission and concentration at a conductive notch is proposed to explain the delay cracking of conducting notch.

  6. PZT95/5陶瓷电致失效机理研究%Failure mechanism of PZT 95/5 under direct current and pulsed electric field

    Institute of Scientific and Technical Information of China (English)

    张福平; 杜金梅; 刘雨生; 刘艺; 刘高旻; 贺红亮

    2011-01-01

    The failure mechanism of PZT 95/5 under direct current and pulsed electric field is studied by experiment and theoretical analysis in this paper. The electrothermal coupled failure is the key mode when the PZT 95/5 is subjected to direct current. But when the pulsed electric field is applied to the PZT 95/5, the resonance effect and the relation between energy and frequency being considered, the vibrant energy shifts to high frequency and the possibility of electromechanical-coupled failure is increased with decreasing pulse duration. When the pulse duration is increased, the failure behavior transfers gradually from mechanical coupled with electric failure to direct current failure mode.%对PZT 95/5陶瓷在直流电场、脉冲方波电场以及半正弦波电场作用下的失效机理进行了理论和实验分析.结果表明:在直流作用下,其失效机理以热-电耦合失效为主;而在脉冲电场作用下,考虑振动冲击效应以及相关的力谱分布,脉宽越短,能量向高频偏移,越可能发生力-电耦合失效;当脉宽增加,PZT 95/5陶瓷失效机理将从力-电耦合失效逐步转变成直流失效模式.

  7. Bulk dielectric and magnetic properties of PFW-PZT ceramics: absence of magnetically switched-off polarization.

    Science.gov (United States)

    Kempa, M; Kamba, S; Savinov, M; Maryško, M; Frait, Z; Vaněk, P; Tomczyk, M; Vilarinho, P M

    2010-11-10

    We investigated ceramics samples of solid solutions of [PbFe(2/3)W(1/3)O(3)](x)-[PbZr(0.53)Ti(0.47)O(3)](1 - x) (PFW(x)-PZT(1 - x), x = 0.2 and 0.3) by means of broad-band dielectric spectroscopy, differential scanning calorimetry and SQUID magnetometry. We did not confirm the observations of Kumar et al (2009 J. Phys.: Condens. Matter 21 382204), who reported on reversible suppression of ferroelectric polarization in polycrystalline PFW(x)-PZT(1 - x) thin films for magnetic fields above 0.5 T. We did not observe any change of ferroelectric polarization with external magnetic fields up to 3.2 T. Pirc et al (2009 Phys. Rev. B 79 214114) developed a theory explaining the reported large magnetoelectric effect in PFW(x)-PZT(1 - x), taking into account relaxor magnetic and relaxor ferroelectric properties of the system. Our data revealed classical ferroelectric properties below 525 K and 485 K in samples with x = 0.2 and 0.3, respectively. Moreover, paramagnetic behavior was observed down to 4.5 K instead of previously reported relaxor magnetic behavior. It seems that the reported switching-off of ferroelectric polarization in PFW(x)-PZT(1 - x) thin films is not an intrinsic property, but probably an effect of electrodes, interlayers, grain boundaries or second phases presented in polycrystalline thin films.

  8. Analytical modeling of demagnetizing effect in magnetoelectric ferrite/PZT/ferrite trilayers taking into account a mechanical coupling

    Science.gov (United States)

    Loyau, V.; Aubert, A.; LoBue, M.; Mazaleyrat, F.

    2017-03-01

    In this paper, we investigate the demagnetizing effect in ferrite/PZT/ferrite magnetoelectric (ME) trilayer composites consisting of commercial PZT discs bonded by epoxy layers to Ni-Co-Zn ferrite discs made by a reactive Spark Plasma Sintering (SPS) technique. ME voltage coefficients (transversal mode) were measured on ferrite/PZT/ferrite trilayer ME samples with different thicknesses or phase volume ratio in order to highlight the influence of the magnetic field penetration governed by these geometrical parameters. Experimental ME coefficients and voltages were compared to analytical calculations using a quasi-static model. Theoretical demagnetizing factors of two magnetic discs that interact together in parallel magnetic structures were derived from an analytical calculation based on a superposition method. These factors were introduced in ME voltage calculations which take account of the demagnetizing effect. To fit the experimental results, a mechanical coupling factor was also introduced in the theoretical formula. This reflects the differential strain that exists in the ferrite and PZT layers due to shear effects near the edge of the ME samples and within the bonding epoxy layers. From this study, an optimization in magnitude of the ME voltage is obtained. Lastly, an analytical calculation of demagnetizing effect was conducted for layered ME composites containing higher numbers of alternated layers (n ≥ 5). The advantage of such a structure is then discussed.

  9. Performance of PZT based MEMS devices with integrated ZnO electronics

    Science.gov (United States)

    Wallace, Margeaux

    This thesis describes routes to enable increased understanding and performance of lead zirconate titanate-based microelectromechanical systems (MEMS). Emphasis was placed on monolithic integration with interposer electronics, and in understanding the role of mechanical boundary conditions on the ferroelectric/ferroelastic response. Co-processing of ZnO thin film transistors (TFTs) with Pb(Zr0.52 Ti0.48)0.98Nb0.02O3 (PZT)-based piezoelectrics was investigated to assess whether interposer electronics on PZT can serve as a control scheme for large area arrays of sensors or actuators. ZnO TFT processing produced no measured changes in remanent polarization, dielectric constant, loss tangent, or aging rates. The TFT performance also did not degrade when fabricated on top of the PZT, the mobility (> 24 cm/Vs) remaining comparable to TFTs deposited on glass. To show ZnO array integration, a 5x5 array of PZT capacitors on glass was fabricated as a prototype for an adjustable X-ray mirror, where the ZnO TFT were used for row-column addressing of the actuators. 1.5 mum thick sputter deposited PZT on glass patterned with large area (cm2) electrodes had a dielectric constant of >1200, tandelta ˜ 2% and an average remanent polarization >23 muC/cm 2. Photoreactive benzocyclobutene (BCB) electrically isolated the ZnO TFTs from the top electrodes of the piezoelectric. Flex cables were bonded to the wafer using anisotropic conductive film (ACF) to connect the gates (row control) and the drains (column control) in the TFT array to a control box. It was found that when actuating the PZT cells through the TFT array, the glass mirror experienced approximately 1.5 mum of deflection for a 10 V application. Studies on ferroelectric/ferroelastic domain reorientation were also performed on 1.9 mum thick tetragonal {001} oriented PbZr0.3Ti 0.7O3 films doped with 1% Mn. Different mechanical boundary constraints were investigated and domain reorientation was quantified through the intensity

  10. Thermoelectric-pyroelectric hybrid energy generation from thermopower waves in core-shell structured carbon nanotube-PZT nanocomposites

    Science.gov (United States)

    Yeo, Taehan; Hwang, Hayoung; Shin, Dongjoon; Seo, Byungseok; Choi, Wonjoon

    2017-02-01

    There is an urgent need to develop a suitable energy source owing to the rapid development of various innovative devices using micro-nanotechnology. The thermopower wave (TW), which produces a high specific power during the combustion of solid fuel inside micro-nanostructure materials, is a unique energy source for unusual platforms that cannot use conventional energy sources. Here, we report on the significant enhancement of hybrid energy generation of pyroelectrics and thermoelectrics from TWs in carbon nanotube (CNT)-PZT (lead zirconate titanate, P(Z0.5-T0.5)) composites for the first time. Conventional TWs use only charge carrier transport driven by the temperature gradient along the core materials to produce voltage. In this study, a core-shell structure of CNTs-PZTs was prepared to utilize both the temperature gradient along the core material (thermoelectrics) and the dynamic change in the temperature of the shell structure (pyroelectrics) induced by TWs. The dual mechanism of energy generation in CNT-PZT composites amplified the average peak and duration of the voltage up to 403 mV and 612 ms, respectively, by a factor of 2 and 60 times those for the composites without a PZT layer. Furthermore, dynamic voltage measurements and structural analysis in repetitive TWs confirmed that CNT-PZT composites maintain the original performance in multiple TWs, which improves the reusability of materials. The advanced TWs obtained by the application of a PZT layer as a pyroelectric material contributes to the extension of the usable energy portion as well as the development of TW-based operating devices.

  11. Micro-particle manipulation by single beam acoustic tweezers based on hydrothermal PZT thick film

    Directory of Open Access Journals (Sweden)

    Benpeng Zhu

    2016-03-01

    Full Text Available Single-beam acoustic tweezers (SBAT, used in laboratory-on-a-chip (LOC device has promising implications for an individual micro-particle contactless manipulation. In this study, a freestanding hydrothermal PZT thick film with excellent piezoelectric property (d33 = 270pC/N and kt = 0.51 was employed for SBAT applications and a press-focusing technology was introduced. The obtained SBAT, acting at an operational frequency of 50MHz, a low f-number (∼0.9, demonstrated the capability to trap and manipulate a micro-particle sized 10μm in the distilled water. These results suggest that such a device has great potential as a manipulator for a wide range of biomedical and chemical science applications.

  12. Towards a digital sound reconstruction MEMS device: Characterization of a single PZT based piezoelectric actuator

    KAUST Repository

    Carreno, Armando Arpys Arevalo

    2015-04-01

    In this paper we report the fabrication and characterization of a single piezoelectric actuator for digital sound reconstruction. This work is the first step towards the implementation of a true digital micro-loudspeaker by means of an array of acoustic actuators. These actuators consist of a flexible membrane fabricated using polyimide, which is actuated using a Lead-Zirconate-Titanate (PZT) piezoelectric ceramic layer working in the d31 actuation mode. The dimensions of the membrane are of 1mm diameter and 4μm in thickness, which is capable of being symmetrically actuated in both upward and downward directions, due to the back etch step releasing the membrane. Our electrical characterization shows an improvement in the polarization of the piezoelectric material after its final etch patterning step, and our mechanical characterization shows the natural modes of resonance of the stacked membrane. © 2015 IEEE.

  13. Piezoelectric and dielectric properties of Cr-doped PSN-PZN-PZT quaternary piezoelectric ceramics

    Institute of Scientific and Technical Information of China (English)

    SUN Qingchi; WANG Lifeng; LIU Ping; NIE Qiang

    2005-01-01

    PSN-PZN-PZT + x wt.%Cr2O3, x = 0.0-0.9, were prepared by conventional mixed oxide techniques at sintering temperatures of 1220℃-1300℃ for 2 h. The effect of sintering temperature on the microstructure and the piezoelectric properties was investigated by XRD, SEM, and other conventional measurement. The result indicated that with temperature increasing, the valence of Cr ion from Cr5+ or Cr6+ changes into Cr3+, and the piezoelectric properties turn hard. With increasing Cr2O3 content, the amount of rhombohedral phases increases and the morphotropic boundary phase is correspondingly shifts to rhombohedral phase. A uniform microstructure and excellent comprehensive properties were obtained at 1240C as the amount of Cr2O3 is 0.5 wt.%.

  14. Damage evaluation based on a wave energy flow map using multiple PZT sensors.

    Science.gov (United States)

    Liu, Yaolu; Hu, Ning; Xu, Hong; Yuan, Weifeng; Yan, Cheng; Li, Yuan; Goda, Riu; Alamusi, Emptyyn Y; Qiu, Jinhao; Ning, Huiming; Wu, Liangke

    2014-01-23

    A new wave energy flow (WEF) map concept was proposed in this work. Based on it, an improved technique incorporating the laser scanning method and Betti's reciprocal theorem was developed to evaluate the shape and size of damage as well as to realize visualization of wave propagation. In this technique, a simple signal processing algorithm was proposed to construct the WEF map when waves propagate through an inspection region, and multiple lead zirconate titanate (PZT) sensors were employed to improve inspection reliability. Various damages in aluminum and carbon fiber reinforced plastic laminated plates were experimentally and numerically evaluated to validate this technique. The results show that it can effectively evaluate the shape and size of damage from wave field variations around the damage in the WEF map.

  15. Advances in piezoelectric PZT-based RF MEMS components and systems

    Science.gov (United States)

    Benoit, R. R.; Rudy, R. Q.; Pulskamp, J. S.; Polcawich, R. G.; Bedair, S. S.

    2017-08-01

    There is continuing interest in radio frequency (RF) microelectromechanical system (MEMS) devices due to their ability to offer exceptional RF performance, high linearity and low power consumption. To date, there is an impressive amount of RF MEMS components such as; switches, resonators, varactors, and tunable inductors that have enabled smaller, cheaper and more efficient RF systems. RF MEMS devices contain micromachined components that have the ability to move so that a change in the mechanical state of a device will result in a change to the device’s RF properties. There are many common modes of actuation, including, but not limited to: electrostatic, magnetostatic, piezoelectric, and electrothermal actuation. Although there are attractive aspects and drawbacks to each of these technologies, this paper will focus on advances in the application of piezoelectric actuation, and in particular the use of lead zirconium titanate (PZT), for RF MEMS.

  16. Shoe-mounted vibration energy harvester of PZT piezoelectric thin films on metal foils

    Science.gov (United States)

    Nishi, T.; Ito, T.; Hida, H.; Kanno, I.

    2016-11-01

    This paper describes shoe-mounted piezoelectric vibration energy harvesters (PVEHs). The PVEHs were fabricated from Pb(ZrTi)O3 (PZT) thin films which were directly deposited onto Pt/Ti-coated stainless steel foil by rf-magnetron sputtering. We experimentally and theoretically evaluated impulse responses of the PVEHs by applying a simple impulse input on the energy harvesters, typical damped free vibration behaviour was clearly observed, and the output signal was in good agreement with the theoretical value. We measured the output power by applying the impulse input with an optimal load resistance of 33.9 kΩ. The maximum output power was approximately 20 μW, which correspond with the calculated value based on theoretical equation. From these results, the theoretical equation we derived might be helpful for design purposes of the shoe-mounted PVEHs.

  17. INVESTIGATION ON STABILITY OF PZT/EPOXY PIEZOCOMPOSITE WITH PRESSURE AND TEMPERATURE

    Institute of Scientific and Technical Information of China (English)

    Likun Wang; Yuanyuan Wan; Li Li; Lei Qin; Yi Lu

    2009-01-01

    With the universal test machine and temperature test chamber, the effect of pres-sure and temperature on the behavior of 1-3 and 1-3-2 piezocomposites prepared with PZT/epoxy in our lab has been investigated through electrical impedance and dielectric analysis. The per-mittivity, resonant frequency and dielectric loss of the composites have been measured under vertical stress and temperature, and the variety of the material properties under pressure and temperature could also be obtained. The pressure and temperature stability of the composites have been assessed through experiments. The data of these two types of composites indicated that the stability of 1-3-2 composite with pressure was better than that of 1-3 composite, and two composites have almost the same dielectric stability with temperature. However, 1-3-2 composite showed slower frequency variation than 1-3 composite.

  18. Micro-particle manipulation by single beam acoustic tweezers based on hydrothermal PZT thick film

    Science.gov (United States)

    Zhu, Benpeng; Xu, Jiong; Li, Ying; Wang, Tian; Xiong, Ke; Lee, Changyang; Yang, Xiaofei; Shiiba, Michihisa; Takeuchi, Shinichi; Zhou, Qifa; Shung, K. Kirk

    2016-01-01

    Single-beam acoustic tweezers (SBAT), used in laboratory-on-a-chip (LOC) device has promising implications for an individual micro-particle contactless manipulation. In this study, a freestanding hydrothermal PZT thick film with excellent piezoelectric property (d33 = 270pC/N and kt = 0.51) was employed for SBAT applications and a press-focusing technology was introduced. The obtained SBAT, acting at an operational frequency of 50MHz, a low f-number (∼0.9), demonstrated the capability to trap and manipulate a micro-particle sized 10μm in the distilled water. These results suggest that such a device has great potential as a manipulator for a wide range of biomedical and chemical science applications. PMID:27014504

  19. Dielectric Properties and Lattice Distortion in Rhombohedral Phase Region and Phase Coexistence Region of PZT Ceramics

    Institute of Scientific and Technical Information of China (English)

    ZHANG Duan-Ming; ZHONG Zhi-Cheng; HAN Xiang-Yun; YAN Wen-Sheng; SUN Hong-Zhang; YANG Feng-Xia; ZHENG Ke-Yu; WEI Nian; LI Zhi-Hua

    2005-01-01

    In this paper, the relation between the dielectric properties and the lattice distortion in the phase coexistence region is discussed using a phase statistical distribution model, and in the rhombohedral phase region the two connection equations on the dielectric properties and the lattice distortion are established. Particularly, the relation between the dielectric properties and the lattice distortion is investigated in the phase coexistence region of PZT ceramics, and the fitting value of the volume fraction of the tetragonal phase VT to composition x in the equation is determined. Further,the fitting results are well consistent with the related experimental data. It involves more profound physical process than relation between the dielectric properties and composition x.

  20. Homogeneity Analysis of a MEMS-based PZT Thick Film Vibration Energy Harvester Manufacturing Process

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Borregaard, Louise M.

    2012-01-01

    This paper presents a homogeneity analysis of a high yield wafer scale fabrication of MEMS-based unimorph silicon/PZT thick film vibration energy harvesters aimed towards vibration sources with peak vibrations in the range of around 300Hz. A wafer with a yield of 91% (41/45 devices) has been...... indicating that the main variation in open circuit voltage performance is caused by varying quality factor. The average resonant frequency was measured to 333Hz with a standard variation of 9.8Hz and a harvesting bandwidth of 5-10Hz. A maximum power output of 39.3μW was achieved at 1g for the best performing...

  1. Hydrothermal synthesis and characterization of fluorine & manganese co-doped PZT based cuboidal shaped powder

    Science.gov (United States)

    Nawaz, H.; Shuaib, M.; Saleem, M.; Rauf, A.; Aleem, A.

    2016-08-01

    Cuboidal shaped PZT powder particles based composition Pb0.89(Ba, Sr)0.11(Zr0.52Ti0.48)O3 co- doped with 1 mol% manganese and 2 mol% fluorine was prepared through hydrothermal route. 200-250nm size cuboidal particles were observed under FE-SEM. XRD technique revealed that the perovskite type ceramic structure has a dominant rhombohedral phase. The resultant powder particles were then spray dried, uniaxially pressed and sintered at different temperatures to achieve maximum theoretical density. 98% density was obtained in the pellets at a sintering temperature of 1190°C with an average grain size of 1-3um. The electrical properties of sintered samples were also measured before and after poling to evaluate the effect of dopants on piezoelectric properties.

  2. Stress corrosion cracking and its anisotropy of a PZT ferroelectric ceramics

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Stress corrosion cracking (SCC) of a PZT ferroelectric ceramics in various media, such as moist atmosphere, silicon oil, methanol, water and formamide, and its anisotropy have been investigated at constant load test using a single-edge notched tensile specimen. The results showed that SCC could occur in all media, and the threshold stress intensity factor of SCC in water and formamide, KISCC, revealed anisotropy. The KISCC for poling direction parallel to the crack plane, was greater than that perpendicular to the crack plane, similar to the anisotropy of fracture toughness KIC; however, the anisotropy factor of KISCC, which was =1.8 (in formamide) and 2.1 (in water), was larger than that of KIC, which is =1.4. The stress-induced 90° domain switching causes the anisotropy of KIC and KISCC, besides, the resistance of SCC also has anisotropy.

  3. Electrical excitation and optical detection of ultrasounds in PZT based piezoelectric transducers

    Energy Technology Data Exchange (ETDEWEB)

    Babilotte, P; Diallo, O; Hue, L-P Tran Hu; Feuillard, G [University Francois Rabelais de Tours, Laboratory Imaging and Brain, Team Ultrasonic Characterisation and Piezoelectricity, ENIVL, Rue de la Chocolaterie, 41034 BLOIS CEDEX (France); Kosec, M; Kuscer, D, E-mail: philippe.babilotte@univ-tours.fr [Josef Stefan Institute, Jamova cesta 39, 1000 LJUBLJANA (Slovenia)

    2011-01-01

    The displacement response of piezoelectric PZT thick films fabricated by means of electrophoretic deposition and laid down an alumina substrate is investigated using coherent optical detection. According to thickness properties determined by electrical impedance measurements, the film presents a resonance around 40 MHz. Other resonance peaks are observed that correspond to eigen modes of the film substrate couple structure. Uniformity of the response of the integrated structure is studied across the surface of the sample when excited by either a continuous or impulse electrical voltage. Results on the amplitude of the detected signal versus the frequency and the input excitation voltage are reported. The optical detection used in these experiments is complementary to conventional techniques of characterization of piezoelectric devices such as electrical impedance measurements and allows getting information on the displacement response of the device.

  4. Micro-particle manipulation by single beam acoustic tweezers based on hydrothermal PZT thick film

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Benpeng, E-mail: benpengzhu@hust.edu.cn [School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan 430074 (China); State Key Laboratory of Transducer Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Xu, Jiong; Yang, Xiaofei [School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan 430074 (China); Li, Ying; Lee, Changyang; Zhou, Qifa; Shung, K. Kirk [Department of Biomedical Engineering and NIH Transducer Resource Center, University of Southern California, Los Angeles, California 90089-1111 (United States); Wang, Tian; Xiong, Ke [Department of Physics and Key Laboratory of Acoustic and Photonic Materials and Devices of Ministry of Education, Wuhan University, Wuhan 430072 (China); Shiiba, Michihisa; Takeuchi, Shinichi [Medical Engineering Course, Graduate School of Engineering, Toin University of Yokohama, Yokohama 225-8501 (Japan)

    2016-03-15

    Single-beam acoustic tweezers (SBAT), used in laboratory-on-a-chip (LOC) device has promising implications for an individual micro-particle contactless manipulation. In this study, a freestanding hydrothermal PZT thick film with excellent piezoelectric property (d{sub 33} = 270 pC/N and k{sub t} = 0.51) was employed for SBAT applications and a press-focusing technology was introduced. The obtained SBAT, acting at an operational frequency of 50 MHz, a low f-number (∼0.9), demonstrated the capability to trap and manipulate a micro-particle sized 10μm in the distilled water. These results suggest that such a device has great potential as a manipulator for a wide range of biomedical and chemical science applications.

  5. Micromachined bulk PZT tissue contrast sensor for fine needle aspiration biopsy.

    Science.gov (United States)

    Li, Tao; Gianchandani, Roma Y; Gianchandani, Yogesh B

    2007-02-01

    This paper describes a micromachined piezoelectric sensor, integrated into a cavity at the tip of a biopsy needle, and preliminary experiments to determine if such a device can be used for real-time tissue differentiation, which is needed for needle positioning guidance during fine needle aspiration (FNA) biopsy. The sensor is fabricated from bulk lead zirconate titanate (PZT), using a customized process in which micro electro-discharge machining is used to form a steel tool that is subsequently used for batch-mode ultrasonic micromachining of bulk PZT ceramic. The resulting sensor is 50 microm thick and 200 microm in diameter. It is placed in the biopsy needle cavity, against a steel diaphragm which is 300 microm diameter and has an average thickness of 23 microm. Devices were tested in materials that mimic the ultrasound characteristics of human tissue, used in the training of physicians, and with porcine fat and muscle tissue. In both schemes, the magnitude and frequency of an electrical impedance resonance peak showed tissue-specific characteristics as the needle was inserted. For example, in the porcine tissue, the impedance peak frequency changed approximately 13 MHz from the initial 163 MHz, and the magnitude changed approximately 1600 Omega from the initial 2100 Omega, as the needle moved from fat to muscle. Samples including oils and saline solution were tested for calibration, and an empirical tissue contrast model shows an approximately proportional relationship between measured frequency shift and sample acoustic impedance. These results suggest that the device can complement existing methods for guidance during biopsies.

  6. Fabrication and Characterization of PZT Thick Films for Sensing and Actuation

    Directory of Open Access Journals (Sweden)

    Kuo-Ching Kuo

    2007-04-01

    Full Text Available Lead Zirconate Titanate oxide (PZT thick films with thicknesses of up to 10 μmwere developed using a modified sol-gel technique. Usually, the film thickness is less than1 μm by conventional sol-gel processing, while the electrical charge accumulation whichreveals the direct effect of piezoelectricity is proportional to the film thickness and thereforerestricted. Two approaches were adopted to conventional sol-gel processing – precursorconcentration modulation and rapid thermal annealing. A 10 μm thick film was successfullyfabricated by coating 16 times via this technique. The thickness of each coating layer wasabout 0.6 μm and the morphology of the film was dense with a crack-free area as large as 16mm2. In addition, the structure, surface morphology and physical properties werecharacterized by X-ray diffraction (XRD, scanning electron microscopy (SEM and atomicforce microscopy (AFM and electrical performance. The dielectric constant and hysteresisloops were measured as electric characteristics. This study investigates the actuation andsensing performance of the vibrating structures with the piezoelectric thick film. Theactuation tests demonstrated that a 4 mm x 4 mm x 6.5 μm PZT film drove a 40 mm x 7 mmx 0.5 mm silicon beam as an actuator. Additionally, it generated an electrical signal of 60mVpp as a sensor, while vibration was input by a shaker. The frequencies of the first twomodes of the beam were compared with the theoretical values obtained by Euler-Bernoullibeam theory. The linearity of the actuation and sensing tests were also examined.

  7. Features ofd15 mode PZT-51 ceramic cantilever piezoelectric energy harvester with parallel connection%并联结构d15模式PZT-51悬臂梁的俘能性能

    Institute of Scientific and Technical Information of China (English)

    张智雄; 郑学军; 张勇; 梅靖羚; 费明祥; 祝元坤

    2015-01-01

    Utilizing the high shear piezoelectric coefficient of PZT-51 ceramic, the parallel connection device ofd15 mode PZT-51 cantilever beam was designed and fabricated. The dependences of output peak-to-peak voltage and output power on frequency were studied at various load resistances. The dependence of peak-to-peak voltage on excitation voltage and the resonance transient output voltage were measured at various load resistances. Maximum output peak-to-peak voltage of 1.96 V and maximum output power of 19.21μW for PEH with load resistance of 100kΩare obtained at frequency of 96 Hz. With increasing vibration excitation voltage, the output peak-to-peak voltage of PEH increases. The proposed structure will provide useful guidelines for the design ofd15 mode piezoelectric energy harvesters.%利用高剪切压电系数,设计并制作并联结构d15模式PZT-51悬臂梁装置,测量其在不同负载电阻下输出峰-峰值电压和输出功率随频率变化的关系以及不同负载电阻下共振瞬时输出电压和振动激励电压与输出峰-峰值电压关系.当频率为96 Hz、负载电阻为100 kΩ时,该PZT-51悬臂梁装置的输出峰-峰值电压最大值为1.96 V,输出功率达到最大为19.21 μW.随着振动激励电压的增大,并联结构d15模式PZT-51悬臂梁装置的输出峰-峰值电压随之增大,并联结构d15模式PZT-51悬臂梁俘能特性的研究可为设计d15模式压电俘能器提供指导.

  8. Homogeneity analysis of high yield manufacturing process of mems-based pzt thick film vibrational energy harvesters

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, Ruichao; Pedersen, C.M.

    2011-01-01

    This work presents a high yield wafer scale fabrication of MEMS-based unimorph silicon/PZT thick film vibrational energy harvesters aimed towards vibration sources with peak frequencies in the range of a few hundred Hz. By combining KOH etching with mechanical front side protection, SOI wafer...... to accurately define the thickness of the silicon part of the harvester and a silicon compatible PZT thick film screen-printing technique, we are able to fabricate energy harvesters on wafer scale with a yield higher than 90%. The characterization of the fabricated harvesters is focused towards the full wafer....../mass-production aspect; hence the analysis of uniformity in harvested power and resonant frequency....

  9. Effects of CeO2 doping on the structure and properties of PSN-PZN-PMS-PZT piezoelectric ceramics

    Institute of Scientific and Technical Information of China (English)

    SUN Qingchi; LU Cuimin; ZHOU Hua

    2005-01-01

    Quinary system piezoelectric ceramics PSN-PZN-PMS-PZT were prepared by using a two-step method. The effects of CeO2 doping on piezoelectric and dielectric properties of the system were investigated at morphotropic phase boundary (MPB). The results reveal that the relative dielectric constant εT33 / ε0, the Curie temperature Tc, the piezoelectric constant d33, the mechanical quality factor Qm, and the electromechanical coupling coefficient Kp are changed with the increase of CeO2 content. On the other hand, the effects of CeO2 doping on the dielectric properties of PSN-PZN-PMS-PZT piezoelectric ceramics at high electric field are consistent with the change at weak electric field. The values of dielectric constant and dielectric loss are enhanced with the increasing of electric field.

  10. Easy installation method of piezoceramic (PZT) transducers for health monitoring of structures using electro-mechanical impedance technique

    Science.gov (United States)

    Annamdas, Venu Gopal Madhav; Radhika, Madhav Annamdas; Yang, Yaowen

    2009-03-01

    Impedance-based structural health monitoring (SHM) technique has been developed using piezo-ceramic (PZT) transducers either by surface bonding or embedding inside the structure to detect damage at the earliest possible stage using signatures. However, this technique requires PZT to be permanently attached to the structures. Furthermore permanent attachment will influence the appearance of the host structure and during replacement of faulty transducer, the use of de bonding tools may spoils the surface and beneath. Hence the present study is aimed to fabricate a portable structure, where PZTs are bonded on it and later the portable structure is attached to the host structure. This portable structure is easy to install during monitoring period and uninstall after recording the monitoring signatures of the host structure. This method protects the surface of the host structure to be monitored and will have same efficiency as that of permanently attached PZTs.

  11. Thickness dependence of electrical properties of PZT films deposited on metal substrates by laser-assisted aerosol deposition.

    Science.gov (United States)

    Baba, S; Tsuda, H; Akedo, J

    2008-05-01

    Dependence of electrical properties-dielectric, ferroelectric, and piezoelectric properties-on film thickness was studied for lead-zirconate titanate (PZT) thick films directly deposited onto stainless-steel (SUS) substrates in actuator devices by using a carbon dioxide (CO(2) ), laser assisted aerosol deposition technique. Optical spectroscopic analysis data and laser irradiation experiments revealed that absorption at a given wavelength by the film increased with increasing film thickness. Dielectric constant epsilon, remanent polarization value P(r), and coercive field strength E(c) of PZT films directly deposited onto a SUS-based piezoelectric actuator substrate annealed by CO(2) laser irradiation at 850 degrees C improved with increasing film thickness, and for films thicker than 25 microm, epsilon 800, P(r) 40 microC/cm(2), and E(c) 45 kV/cm. In contrast, the displacement of the SUS-based actuator with the laser-annealed PZT thick film decreased with increasing film thickness.

  12. Concrete Infill Monitoring in Concrete-Filled FRP Tubes Using a PZT-Based Ultrasonic Time-of-Flight Method.

    Science.gov (United States)

    Luo, Mingzhang; Li, Weijie; Hei, Chuang; Song, Gangbing

    2016-12-07

    Concrete-filled fiber-reinforced polymer tubes (CFFTs) have attracted interest for their structural applications in corrosive environments. However, a weak interfacial strength between the fiber-reinforced polymer (FRP) tube and the concrete infill may develop due to concrete shrinkage and inadequate concrete compaction during concrete casting, which will destroy the confinement effect and thereby reduce the load bearing capacity of a CFFT. In this paper, the lead zirconate titanate (PZT)-based ultrasonic time-of-flight (TOF) method was adopted to assess the concrete infill condition of CFFTs. The basic idea of this method is that the velocity of the ultrasonic wave propagation in the FRP material is about half of that in concrete material. Any voids or debonding created along the interface between the FRP tube and the concrete will delay the arrival time between the pairs of PZT transducers. A comparison of the arrival times of the PZT pairs between the intact and the defected CFFT was made to assess the severity of the voids or the debonding. The feasibility of the methodology was analyzed using a finite-difference time-domain-based numerical simulation. Experiments were setup to validate the numerical results, which showed good agreement with the numerical findings. The results showed that the ultrasonic time-of-flight method is able to detect the concrete infill condition of CFFTs.

  13. PERFORMANCE, COMBUSTION AND EMISSION CHARACTERISTICS OF PZT LOADED CYANATE MODIFIED EPOXY COATED COMBUSTION CHAMBER IN DIESEL ENGINE

    Directory of Open Access Journals (Sweden)

    Vijaya Kumar K.R

    2010-07-01

    Full Text Available Energy conservation and emissions have become increasing concern over the past few decades. PZT loaded cyanate modified epoxy (60EPCY 20PI coated material were initially investigated for adiabatic diesel engines based on first law of thermodynamics prediction of significant fuel economy improvements, reduction in heat rejection and potential increased power density of the diesel engines. The purpose of 60EPCY 20PI is to focus on developing binder systems with low thermal conductivity and improve the coating durability under high load condition. The coating material is made up of 20% Lead Zirconate Titanate (PZT in 60% Cyanate modified Epoxy system. The triazine ring of cyanate ester offers better thermal resistance characteristics to the epoxy system. Experimental investigation is carried out under different load condition on a single cylinder dieselengine with PZT loaded cyanate modified epoxy resin system of 0.5 mm thickness to the piston, cylinder head with valves and cylinder liner. The result showed 15.89 %of reduced specific fuel consumption. Emissions of unburnt hydrocarbon, carbon monoxide are reduced.

  14. Stripe-PZT Sensor-Based Baseline-Free Crack Diagnosis in a Structure with a Welded Stiffener

    Directory of Open Access Journals (Sweden)

    Yun-Kyu An

    2016-09-01

    Full Text Available This paper proposes a stripe-PZT sensor-based baseline-free crack diagnosis technique in the heat affected zone (HAZ of a structure with a welded stiffener. The proposed technique enables one to identify and localize a crack in the HAZ using only current data measured using a stripe-PZT sensor. The use of the stripe-PZT sensor makes it possible to significantly improve the applicability to real structures and minimize man-made errors associated with the installation process by embedding multiple piezoelectric sensors onto a printed circuit board. Moreover, a new frequency-wavenumber analysis-based baseline-free crack diagnosis algorithm minimizes false alarms caused by environmental variations by avoiding simple comparison with the baseline data accumulated from the pristine condition of a target structure. The proposed technique is numerically as well as experimentally validated using a plate-like structure with a welded stiffener, reveling that it successfully identifies and localizes a crack in HAZ.

  15. The Effect of Shock Stress and Field Strength on Shock-Induced Depoling of Normally Poled PZT 95/5

    Energy Technology Data Exchange (ETDEWEB)

    CHHABILDAS,LALIT C.; FURNISH,MICHAEL D.; MONTGOMERY,STEPHEN T.; SETCHELL,ROBERT E.

    1999-09-01

    Shock-induced depoling of the ferroelectric ceramic PZT 95/5 is utilized in a number of pulsed power devices. Several experimental and theoretical efforts are in progress in order to improve numerical simulations of these devices. In this study we have examined the shock response of normally poled PZT 95/5 under uniaxial strain conditions. On each experiment the current produced in an external circuit and the transmitted waveform at a window interface were recorded. The peak electrical field generated within the PZT sample was varied through the choice of external circuit resistance. Shock pressures were varied from 0.6 to 4.6 GPa, and peak electrical fields were varied from 0.2 to 37 kV/cm. For a 2.4 GPa shock and the lowest peak field, a nearly constant current governed simply by the remanent polarization and the shock velocity was recorded. Both decreasing the shock pressure and increasing the electrical field resulted in reduced current generation, indicating a retardation of the depoling kinetics.

  16. Fabrication and characterization of size-controlled single-crystal-like PZT nanofibers by sol–gel based electrospinning

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Juan; Gao, Qian; He, Haiyan; Li, Xiang, E-mail: xiang.li@zju.edu.cn; Ren, Zhaohui; Liu, Yong; Shen, Ge; Xu, Gang; Zhang, Xiwen; Han, Gaorong, E-mail: hgr@zju.edu.cn

    2013-12-05

    Highlights: •Single-crystal-like PZT nanofibers were fabricated by electrospinning and calcination. •Fiber diameter was precisely controlled by solution viscosity and electrospinning parameters. •Pyrolysis is a key factor for fabrication of single-crystal-like structure. -- Abstract: Size-controlled single-crystal-like lead zirconate titanate (PbZr{sub 0.52}Ti{sub 0.48}O{sub 3}, PZT) ceramic fibers have been successfully prepared by sol–gel based electrospinning and subsequent calcination process, and their morphology, crystal structure have been characterized at nanoscale. The fiber diameter can be precisely controlled from ∼50 to 540 nm by varying the PVP concentration and electrospinning process parameters. The crystal structure of the nanofibers pyrolyzed at 400 °C for 0.5 h and calcined at 650 °C for 2 h is proved to be single-crystal-like tetragonal perovskite phase. A formation mechanism is also discussed based on the thermal decomposition process, effect of the calcination and pyrolysis procedure, using the thermogravimetry/differential scanning caborimetry (TG/DSC), X-ray diffraction (XRD) and transmission electron microscopy (TEM). It is found that the pyrolysis procedure is a critical factor for the fabrication of single-crystal-like structure PZT nanofibers using electrospinning.

  17. Study of mechanical-magnetic and electromagnetic properties of PZT/Ni film systems by a novel bulge technique

    Science.gov (United States)

    Liu, Q.; Zhou, W.; Ding, J.; Xiao, M.; Yu, Z. J.; Xu, H.; Mao, W. G.; Pei, Y. M.; Li, F. X.; Feng, X.; Fang, D. N.

    2017-02-01

    A novel multiple functional bulge apparatus was designed to study the mechanical-electronic-magnetic characteristics of electromagnetic materials. The elastic modulus difference effect of Ni thin film was observed and it was about 22.16% in the demagnetized and magnetization saturated states. The mechanical-magnetic behaviors of Ni and lead-titanate zirconate (PZT)/Ni films were in-situ measured by using the new bulge systems, respectively. The evolutions of three key material properties in hysteresis loop including saturation magnetization, remanent magnetization and coercive field were discussed in detail, respectively. The mechanisms of mechanical-magnetic coupled behaviors of Ni and PZT/Ni films were analyzed with the aid of the competitive relationship of stress and magnetization. Similarly, the electronic-magnetic characteristics of PZT/Ni films were in-situ measured by using this experimental system. The evolution of saturated magnetization, remanent magnetization and coercive field Kerr signals were discussed with the magneto-elastic anisotropy energy point. In this paper, a suitable mechanical-electronic-magnetic bulge measurement system was established, which would provide a good choice for further understanding the multi field coupling characteristics of electromagnetic film materials.

  18. Effect of Laser Irradiation on Dielectric Properties of PZT-4 Ceramic%激光辐照对PZT-4陶瓷介电性能的影响

    Institute of Scientific and Technical Information of China (English)

    赵艳; 蒋毅坚; 于永明; 季凌飞; 鲍勇

    2012-01-01

    研究了CO2激光辐照对PZT-4陶瓷介电性能的影响.在一定的激光辐照功率密度下,PZT-4陶瓷的介电常数下降约5%,介电损耗下降约60%,矫顽场增加.结合拉曼光谱、扫描电子显微镜、X射线衍射以及后退火处理探讨了激光辐照PZT-4陶瓷的改性机理,结果表明,激光辐照后陶瓷介电性能的变化主要与其微结构有关,辐照使得陶瓷产生了较大的张应力,晶格常数变大,B位离子更容易偏离氧八面体中心,氧八面体扭曲,使其电畴活性下降,阻碍了极化翻转,材料性能变“硬”.%The effect of CO2 laser irradiation on the dielectric properties of PZT-4 ceramic is investigated. After laser irradiation, dielectric permittivity and dielectric loss of the ceramic decrease 5% and 60% , respectively, and the coercivity increases. The mechanism of the changes are analysed by Raman scattering, scanning electron microscope (SEM), X-ray diffraction (XRD) and the annealing process. It is shown that the microstructure changes of the irradiated sample mainly account for the dielectric properties. The CO2 laser irradiation could induce the tension stress, leading to the larger lattice parameter and the deviation of B site ion from the center of oxygen octahedron. The distortion of the oxygen octahedron results in the less activation of electric domains. Therefore, the polarization switching of the electric domains become more difficult, exhibiting the properties of " hard". This suggests that the laser irradiation may offer a new approach for the fabrication of lead zirconate titanate (PZT) based "hard martial" in several seconds without any ions addition.

  19. Growth and characterization of zinc oxide and PZT films for micromachined acoustic wave devices

    Science.gov (United States)

    Yoon, Sang Hoon

    The ability to detect the presence of low concentrations of harmful substances, such as biomolecular agents, warfare agents, and pathogen cells, in our environment and food chain would greatly advance our safety, provide more sensitive tools for medical diagnostics, and protect against terrorism. Acoustic wave (AW) devices have been widely studied for such applications due to several attractive properties, such as rapid response, reliability, portability, ease of use, and low cost. The principle of these sensors is based on a fundamental feature of the acoustic wave that is generated and detected by a piezoelectric material. The performance of the device, therefore, greatly depends on the properties of piezoelectric thin film. The required properties include a high piezoelectric coefficient and high electromechanical coefficients. The surface roughness and the mechanical properties, such as Young's modulus and hardness, are also factors that can affect the wave propagation of the device. Since the film properties are influenced by the structure of the material, understanding thin film structure is very important for the design of high-performance piezoelectric MEMS devices for biosensor applications. In this research, two piezoelectric thin film materials were fabricated and investigated. ZnO films were fabricated by CSD (Chemical Solution Deposition) and sputtering, and PZT films were fabricated by CSD only. The process parameters for solution derived ZnO and PZT films, such as the substrate type, the effect of the chelating agent, and heat treatment, were studied to find the relationship between process parameters and thin film structure. In the case of the sputtered ZnO films, the process gas types and their ratio, heat treatment in situ, and post deposition were investigated. The key results of systematic experiments show that the combined influence of chemical modifiers and substrates in chemical solution deposition have an effect on the crystallographic

  20. Study of dielectric and piezoelectric properties of CNT reinforced PZT-PVA 0-3 composite

    Science.gov (United States)

    Vyas, Prince; Prajapat, Rampratap; Manmeeta, Saxena, Dhiraj

    2016-05-01

    Ferroelectric ceramic/polymer composites have the compliance of polymers which overcome the problems of brittleness in ceramics. By imbedding piezoelectric ceramic powder into a polymer matrix, 0-3 composites with good mechanical properties and high dielectric breakdown strength can be developed. The obtained composites of 0-3 connectivity exhibit the piezoelectric properties of ceramics and flexibility, strength and lightness of polymer. These composites can be used in vibration sensing and transducer applications specially as piezoelectric sensors. A potential way to improve piezoelectric& dielectric properties of theses composites is by inclusion of another conductive phase in these composites as reported in the literature. In present work, we prepared PZT-PVA 0-3 composites with 60% ceramic volume fraction reinforced with CNTs with volume ranging from 0 to 1.5 vol%. These CNT reinforced composites were obtained using hot press method with thickness of 200 µm having 0-3 conductivity. These composites were poled applying DC voltage. Dielectric properties of these samples were obtained in a wide frequency range (100 Hz to 1 Mhz) at room temperature. The piezoelectric properties of these composites were analyzed by measuring piezoelectric charge constants (d33). The dielectric and piezoelectric properties of these composites were studied as a function of CNT volume content. In these reinforced composites, CNTs act as a conductive filler dispersed in the matrix which in turn facilitates poling and results in an increase of the piezoelectric properties of the composite due to formation of percolation path through the composites. With a CNT content of 0.3 vol.% in PZT/PVA/CNTs, an increase of 61.3 % was observed in piezoelectric strain factors (d33). In these CNT reinforced composites, a substantial increase (approx. 67%) was also observed in dielectric constant and approximately 89% increase was observed in dielectric loss factor. Results so obtained are in the good

  1. Single dc magnetic field tunable electromechanical resonance in Terfenol-D/PZT/Terfenol-D trilayer composites

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Wang, E-mail: wangwei1@njnu.edu.cn [Opto-Electronic Technology Key Laboratory of Jiangsu Province, School of Physical Science and Technology, Nanjing Normal University, Nanjing 210023 (China); JingJing, Ye; Jie, Wu [Opto-Electronic Technology Key Laboratory of Jiangsu Province, School of Physical Science and Technology, Nanjing Normal University, Nanjing 210023 (China); LiSheng, Zhou [Hangzhou Applied Acoustics Research Institute, National Key Laboratory of Science and Technology on Sonar, Hang Zhou 310012 (China); Bin, Luo Xiao; Ning, Zhang [Opto-Electronic Technology Key Laboratory of Jiangsu Province, School of Physical Science and Technology, Nanjing Normal University, Nanjing 210023 (China)

    2014-10-01

    Single dc magnetic field excited electromechanical resonance (EMR) in Terfenol-D/PZT/Terfenol-D trilayer composites structure was experimentally investigated and theoretically analyzed. The experiment proves dc magnetic field influence on EMR of magnetoelectric (ME) composites. The tuning of approximately 17.7 kHz was obtained in a dc magnetic field of 100 mT. The theory of dc magnetic field tunable resonance frequency shift containing different ferroelectric volume fractions in layer magnetoelectric composites is presented. This tuning is due to the magnetoelectric interactions in the layered ME composites structure. - Highlights: • Magnetically excited EMR in trilayer composites structure was studied. • The EMR frequency shift is approximately 17.7 kHz with dc magnetic field of 100 mT. • Calculation of capacitance as a function of frequency under different magnetic fields. • Dependence of ferroelectric volume fraction on EMR shifts have been revealed. • Promise for control EMR with a dc magnetic field is suggested.

  2. Microfabrication and Integration of a Sol-Gel PZT Folded Spring Energy Harvester

    Directory of Open Access Journals (Sweden)

    Jonathan Lueke

    2015-05-01

    Full Text Available This paper presents the methodology and challenges experienced in the microfabrication, packaging, and integration of a fixed-fixed folded spring piezoelectric energy harvester. A variety of challenges were overcome in the fabrication of the energy harvesters, such as the diagnosis and rectification of sol-gel PZT film quality and adhesion issues. A packaging and integration methodology was developed to allow for the characterizing the harvesters under a base vibration. The conditioning circuitry developed allowed for a complete energy harvesting system, consisting a harvester, a voltage doubler, a voltage regulator and a NiMH battery. A feasibility study was undertaken with the designed conditioning circuitry to determine the effect of the input parameters on the overall performance of the circuit. It was found that the maximum efficiency does not correlate to the maximum charging current supplied to the battery. The efficiency and charging current must be balanced to achieve a high output and a reasonable output current. The development of the complete energy harvesting system allows for the direct integration of the energy harvesting technology into existing power management schemes for wireless sensing.

  3. Dynamic modeling and analysis of the PZT-bonded composite Timoshenko beams: Spectral element method

    Science.gov (United States)

    Lee, Usik; Kim, Daehwan; Park, Ilwook

    2013-03-01

    The health of thin laminated composite beams is often monitored using the ultrasonic guided waves excited by wafer-type piezoelectric transducers (PZTs). Thus, for the smart composite beams which consist of a laminated composite base beam and PZT layers, it is very important to develop a very reliable mathematical model and to use a very accurate computational method to predict accurate dynamic characteristics at very high ultrasonic frequency. In this paper, the axial-bending-shear-lateral contraction coupled differential equations of motion are derived first by the Hamilton's principle with Lagrange multipliers. The smart composite beam is represented by a Timoshenko beam model by adopting the first-order shear deformation theory (FSDT) for the laminated composite base beam. The axial deformation of smart composite beam is improved by taking into account the effects of lateral contraction by adopting the concept of Mindlin-Herrmann rod theory. The spectral element model is then formulated by the variation approach from coupled differential equations of motion transformed into the frequency domain via the discrete Fourier transform. The high accuracy of the present spectral element model is verified by comparing with other solution methods: the finite element model developed in this paper and the commercial FEA package ANSYS. Finally the dynamics and wave characteristics of some example smart composite beams are investigated through the numerical studies.

  4. Importance of composite parameters in enhanced power conversion efficiency of Terfenol-D/PZT magnetoelectric gyrators

    Science.gov (United States)

    Leung, Chung Ming; Zhuang, Xin; Xu, Junran; Li, Jiefang; Srinivasan, G.; Viehland, D.

    2017-03-01

    A gyrator that is capable of current-to-voltage conversion can be realized with a magnetoelectric (ME) composite of ferromagnetic and ferroelectric phases placed in a coil. Here, we report the dependence of the power conversion efficiency (PE) on the relative thickness of the two ferroic phases in a gyrator of Terfenol-D and PZT. Both experimental and theoretical results on PE as a function of composite parameters, such as thickness ratio of the ferroic layers (n), magnetic field bias (HBias) and several gyrator parameters, such as the resistance load (RL), were discussed. By decreasing the thickness ratio of Terfenol-D to composite (n = 0.28) in coil-ME gyrators, a high power efficiency of 73.9% was found at a fundamental resonance frequency of 72.5 kHz under a HBias of 1000 Oe and RL = 2.6 kΩ in experiments. At the same time, the non-linear mechanical loss was reduced by decreasing the value of n which resulted in a flat response over a wide HBias range. This improved power efficiency promises ME gyrators for power transfer devices.

  5. Improving the magnetoelectric performance of Metglas/PZT laminates by annealing in a magnetic field

    Science.gov (United States)

    Freeman, E.; Harper, J.; Goel, N.; Gilbert, I.; Unguris, J.; Schiff, S. J.; Tadigadapa, S.

    2017-08-01

    A comprehensive investigation of magnetostriction optimization in Metglas 2605SA1 ribbons is performed to enhance magnetoelectric performance. We explore a range of annealing conditions to relieve remnant stress and align the magnetic domains in the Metglas, while minimizing unwanted crystallization. The magnetostriction coefficient, magnetoelectric coefficient, and magnetic domain alignment are correlated to optimize magnetoelectric performance. We report on direct magnetostriction observed by in-plane Doppler vibrometer and domain imagining using scanning electron microscopy with polarization analysis for a range of annealing conditions. We find that annealing in an oxygen-free environment at 400 {}\\circ {{C}} for 30 min yields an optimal magnetoelectric coefficient, magnetostriction and magnetostriction coefficient. The optimized ribbons had a magnetostriction of 50.6 ± 0.2 μ {{m}} {{{m}}}-1 and magnetoelectric coefficient of 79.3 ± 1.5 µm m-1 mT-1. The optimized Metglas 2605SA1 ribbons and PZT-5A (d31 mode) sensor achieves a magnetic noise floor of approximately 600 pT {{{H}}{{z}}}-1/2 at 100 Hz and a magnetoelectric coefficient of 6.1 ± 0.03 MV m-1 T-1.

  6. Trajectory tracking and vibration control in a space frame flexible structure with a PZT stack actuator

    Science.gov (United States)

    Garcia-Perez, Oscar A.; Silva-Navarro, G.; Peza-Solís, J. F.; Trujillo-Franco, L. G.

    2015-04-01

    This work deals with the robust asymptotic output tracking control problem of the tip position of a space frame flexible structure, mounted on a rigid revolute servomechanism actuated and controlled with a dc motor. The structure is also affected by undesirable vibrations due to excitation of its first lateral vibration modes and possible variations of the tip mass. The overall flexible structure is modeled by using finite element methods and this is validated via experimental modal analysis techniques. The tip position of the structure is estimated from acceleration and strain gauge measurements. The asymptotic output tracking problem is formulated and solved by means of Passivity-Based and Sliding-Mode Control techniques, applied to the dc motor coupled to the rigid part of the structure, and those undesirable vibrations are simultaneously attenuated by an active vibration control using Positive Position Feedback control schemes implemented on a PZT stack actuator properly located into the mechanical structure. The investigation also addresses the trajectory tracking problem of fast motions, with harmonic excitations close to the first vibration modes of the structure. The overall dynamic performance is evaluated and validated by numerical and experimental results.

  7. The domain structure and polarization retention properties of PT/PZT/PT ferroelectric thin film

    Institute of Scientific and Technical Information of China (English)

    WANG LongHai; Yu Jun; ZHAO SuLing; ZHENG ChaoDuan; WANG YunBo; GAO JunXiong

    2007-01-01

    3The Research & Test Center of Materials, Wuhan University of Technology, Wuhan 430070, ChinaThe highly oriented perovskite-phase PT/PZT/PT ferroelectric thin film was prepared by sol-gel method. The domain structures and polarization retention properties were investigated by scanning force microscopy. The amplitude and phase images of piezoresponse show complex various contrasts of dark, bright and gray.The complex variation of contrast in piezoresponse images results from the perplexing orientation of grains and arrangement of domains in the ferroelectric films.The bright and dark areas in phase images correspond to top-to-bottom and bottom-to-top polarization oriented c-domain, respectively. The gray areas are c-domains with the polarization vector deviating from the direction normal to the film plane. The surface potential images of EFM are bright contrast, which is due to positive charges trapped on the film surface after being polarized by positive voltage. And the brighter contrast is obtained from the higher electric field. The time-dependent surface potential images and line potential profiles show that the potential decays with time. And the decay in the region polarized by higher electric field is faster, especially at 15 min. This indicates that the polarization retention is related to the polarized electric field. Better retention properties may be obtained from a proper polarized electric field.

  8. The domain structure and polarization retention properties of PT/PZT/PT ferroelectric thin film

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The highly oriented perovskite-phase PT/PZT/PT ferroelectric thin film was pre- pared by sol-gel method. The domain structures and polarization retention proper- ties were investigated by scanning force microscopy. The amplitude and phase images of piezoresponse show complex various contrasts of dark, bright and gray. The complex variation of contrast in piezoresponse images results from the per- plexing orientation of grains and arrangement of domains in the ferroelectric films. The bright and dark areas in phase images correspond to top-to-bottom and bot- tom-to-top polarization oriented c-domain, respectively. The gray areas are c-domains with the polarization vector deviating from the direction normal to the film plane. The surface potential images of EFM are bright contrast, which is due to positive charges trapped on the film surface after being polarized by positive volt- age. And the brighter contrast is obtained from the higher electric field. The time-dependent surface potential images and line potential profiles show that the potential decays with time. And the decay in the region polarized by higher electric field is faster, especially at 15 min. This indicates that the polarization retention is related to the polarized electric field. Better retention properties may be obtained from a proper polarized electric field.

  9. Microfabrication and integration of a sol-gel PZT folded spring energy harvester.

    Science.gov (United States)

    Lueke, Jonathan; Badr, Ahmed; Lou, Edmond; Moussa, Walied A

    2015-05-26

    This paper presents the methodology and challenges experienced in the microfabrication, packaging, and integration of a fixed-fixed folded spring piezoelectric energy harvester. A variety of challenges were overcome in the fabrication of the energy harvesters, such as the diagnosis and rectification of sol-gel PZT film quality and adhesion issues. A packaging and integration methodology was developed to allow for the characterizing the harvesters under a base vibration. The conditioning circuitry developed allowed for a complete energy harvesting system, consisting a harvester, a voltage doubler, a voltage regulator and a NiMH battery. A feasibility study was undertaken with the designed conditioning circuitry to determine the effect of the input parameters on the overall performance of the circuit. It was found that the maximum efficiency does not correlate to the maximum charging current supplied to the battery. The efficiency and charging current must be balanced to achieve a high output and a reasonable output current. The development of the complete energy harvesting system allows for the direct integration of the energy harvesting technology into existing power management schemes for wireless sensing.

  10. Real-Time Performance of Mechatronic PZT Module Using Active Vibration Feedback Control.

    Science.gov (United States)

    Aggogeri, Francesco; Borboni, Alberto; Merlo, Angelo; Pellegrini, Nicola; Ricatto, Raffaele

    2016-09-25

    This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that seriously compromise the quality of the workpiece. The active vibration control (AVC) device is composed of a host part integrated with sensors and actuators synchronized by a regulator; it is able to make a self-assessment and adjust to alterations in the environment. In particular, an innovative smart actuator has been designed and developed to satisfy machining requirements during active vibration control. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving a machine tool, PZT actuator and controller models. The Hardware in the Loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

  11. SEMICONDUCTOR DEVICES Fabrication and characterization of an AlGaN/PZT detector

    Science.gov (United States)

    Yan, Zhang; Jinglan, Sun; Nili, Wang; Li, Han; Xiangyang, Liu; Xiangyang, Li; Xiangjian, Meng

    2010-12-01

    Design, fabrication and characterization of a novel two-color detector for ultraviolet and infrared applications are reported. The detector has a simple multilayer structure composed of n-Al0.3Ga0.7N/i-GaN/p-GaN/SiO2/LaNiO3/PZT/Pt fabricated on a sapphire substrate. Ultraviolet and infrared properties are measured. For the ultraviolet region, a flat band spectral response is achieved in the 302-363 nm band. The detector displays an unbiased responsivity of 0.064 A/W at 355 nm. The current-voltage curve shows that current at zero bias is -1.57 × 10-12 A. This led to a detectivity of 1.81 × 1011 cm · Hz1/2/W. In the infrared region, the detectivity of the detector is 1.58 × 105 cm · Hz1/2/W at 4 μm.

  12. Silver Doped 0.9PMN-PT-0.1PZT Composite Films for very High Frequency Ultrasonic Transducer Applications.

    Science.gov (United States)

    Hsu, Hsiu-Sheng; Benjauthrit, Vatcharee; Wei, Qiang; Huang, Yuhong; Zhou, Qifa; Shung, K Kirk

    2013-05-01

    A series of silver doping concentration into the 0.9PMN-PT-0.1PZT (PMN-PT-PZT) films via the composite sol-gel technique were prepared. The crystallographic properties and microstructures of PMN-PT-PZT films with the silver dopant were investigated. Additionally, the effect of silver doping on dielectric and ferroelectric properties was examined. The results show that in general, the dielectric permittivity and remnant polarization increase as the silver doping concentration is increased. The PMN-PT-PZT+ 2.5 mol% Ag film exhibits a dielectric constant of 3,610 at 1 kHz and a remnant polarization of 57.6 µC/cm(2) at room temperature. From this silver doped film, very high frequency ultrasonic needle transducers were fabricated and evaluated. The representative transducer had the center frequency of 225 MHz with a -6 dB bandwidth of 29% (65 MHz) and 62 dB insertion loss. The performance of this transducer is comparable to other composite sol-gel films transducer. The results suggest that this silver-doped PMN-PT-PZT film is a promising candidate as an alternative piezoelectric film for very high frequency transducer applications.

  13. Silver doped 0.9PMN-PT-0.1PZT composite films for very high frequency ultrasonic transducer applications

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Hsiu-Sheng [University of Southern California, Department of Biomedical Engineering and NIH Transducer Resource Center, Los Angeles, CA (United States); University of Southern California, Mork Family Department of Chemical Engineering and Materials Science, Los Angeles, CA (United States); Benjauthrit, Vatcharee; Zhou, Qifa; Shung, K.K. [University of Southern California, Department of Biomedical Engineering and NIH Transducer Resource Center, Los Angeles, CA (United States); Wei, Qiang; Huang, Yuhong [Chemat Technology Inc., Northridge, CA (United States)

    2013-05-15

    A series of silver doping concentration into the 0.9PMN-PT-0.1PZT (PMN-PT-PZT) films via the composite sol-gel technique were prepared. The crystallographic properties and microstructures of PMN-PT-PZT films with the silver dopant were investigated. Additionally, the effect of silver doping on dielectric and ferroelectric properties was examined. The results show that in general, the dielectric permittivity and remnant polarization increase as the silver doping concentration is increased. The PMN-PT-PZT+2.5 mol% Ag film exhibits a dielectric constant of 3,610 at 1 kHz and a remnant polarization of 57.6 {mu}C/cm{sup 2} at room temperature. From this silver doped film, very high frequency ultrasonic needle transducers were fabricated and evaluated. The representative transducer had the center frequency of 225 MHz with a -6 dB bandwidth of 29 % (65 MHz) and 62 dB insertion loss. The performance of this transducer is comparable to other composite sol-gel films transducer. The results suggest that this silver-doped PMN-PT-PZT film is a promising candidate as an alternative piezoelectric film for very high frequency transducer applications. (orig.)

  14. Performance of PZT stacks under high-field electric cycling at various temperatures in heavy-duty diesel engine fuel injectors

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hong [ORNL; Lin, Hua-Tay [ORNL; Stafford, Mr Randy [Cummins Inc., Columbus, Indiana

    2016-01-01

    Testing and characterization of large prototype lead zirconate titanate (PZT) stacks present substantial technical challenges to electronic systems. The work in this study shows that an alternative approach can be pursued by using subunits extracted from prototype stacks. Piezoelectric and dielectric integrity was maintained even though the PZT plate specimens experienced an additional loading process involved with the extraction after factory poling. Extracted 10-layer plate specimens were studied by an electric cycle test under an electric field of 3.0/0.0 kV/mm, 100 Hz to 108 cycles, both at room temperature (22 C) and at 50 C. The elevated temperature had a defined impact on the fatigue of PZT stacks. About 48 and 28% reductions were observed in the piezoelectric and dielectric coefficients, respectively, after 108 cycles at 50 C, compared with reductions of 25 and 15% in the respective coefficients at 22 C. At the same time, the loss tangent varied to a limited extent. The evolution of PZT electrode interfacial layers or nearby dielectric layers should account for the difference in the fatigue rates of piezoelectric and dielectric coefficients. But the basic contribution to observed fatigue may result from the buildup of a bias field that finally suppressed the motion of the domain walls. Finally, monitoring of dielectric coefficients can be an effective tool for on-line lifetime prediction of PZT stacks in service if a failure criterion is defined properly.

  15. Performance of PZT stacks under high-field electric cycling at various temperatures in heavy-duty diesel engine fuel injectors

    Science.gov (United States)

    Wang, Hong; Lee, Sung-Min; Lin, Hua-Tay; Stafford, Randy

    2016-04-01

    Testing and characterization of large prototype lead zirconate titanate (PZT) stacks present substantial technical challenges to electronic systems. The work in this study shows that an alternative approach can be pursued by using subunits extracted from prototype stacks. Piezoelectric and dielectric integrity was maintained even though the PZT plate specimens experienced an additional loading process involved with the extraction after factory poling. Extracted 10-layer plate specimens were studied by an electric cycle test under an electric field of 3.0/0.0 kV/mm, 100 Hz to 108 cycles, both at room temperature (22°C) and at 50°C. The elevated temperature had a defined impact on the fatigue of PZT stacks. About 48 and 28% reductions were observed in the piezoelectric and dielectric coefficients, respectively, after 108 cycles at 50°C, compared with reductions of 25 and 15% in the respective coefficients at 22°C. At the same time, the loss tangent varied to a limited extent. The evolution of PZT-electrode interfacial layers or nearby dielectric layers should account for the difference in the fatigue rates of piezoelectric and dielectric coefficients. But the basic contribution to observed fatigue may result from the buildup of a bias field that finally suppressed the motion of the domain walls. Finally, monitoring of dielectric coefficients can be an effective tool for on-line lifetime prediction of PZT stacks in service if a failure criterion is defined properly.

  16. Monitoring the integrity of massive aluminum structures using PZT transducers and the technique of impedance

    Science.gov (United States)

    da Costa, Rosalba; Maia, Joaquim M.; Assef, Amauri A.; Pichorim, Sergio F.; Costa, Eduardo T.; L. S. N. Button, Vera

    2015-04-01

    Safety, performance, economy and durability are essential items to qualify materials for the manufacturing of structures used in different areas. Generally, the materials used for this purpose are formed by composites and sometimes they can present failure during the manufacturing process. Such failures can also occur during use due to fatigue and wear, causing damage often difficult to be visually detected. In these cases, the use of non destructive testing (NDT) has proven to be a good choice for assessing the materials quality. The objective of this work was the electromechanical impedance evaluation of massive aluminum structures using ultrasonic transducers to detect discontinuities in the material. The tests have been done using an impedance analyzer (Agilent 4294A), an ultrasound transducer (1.6 MHz of central frequency), two types of PZT ceramics (0.267 mm and 1 mm thickness) and four aluminum samples (250 x 50 x 50 mm) with the transducer placed at three different regions. One sample was kept intact (reference) and the others were drilled in three positions with different sizes of holes (5 mm. 8 mm and 11 mm). The electromechanical impedance was recorded for each sample. The root mean square deviation index (RMSD) between the impedance magnitude of the reference and damaged samples was calculated and it was observed an increase in the RMSD due to the increase of the diameter of the holes (failures) in the samples completely drilled. The results show that the proposed methodology is suitable for monitoring the integrity of aluminum samples. The technique may be evaluated in characterizing other materials to be used in the construction of prostheses and orthoses.

  17. Sensing of damage and substrate stress in concrete using electro-mechanical impedance measurements of bonded PZT patches

    Science.gov (United States)

    Narayanan, Arun; Subramaniam, Kolluru V. L.

    2016-09-01

    The influence of stress and induced damage in concrete on the electro-mechanical (EM) impedance response of bonded PZT patches is evaluated for applied compressive loading. Full field displacements obtained from digital image correlation are used to evaluate the level of stress-induced damage in concrete. Stress in the substrate produces an imposed strain on the PZT. A change in the imposed strain produces a rightward frequency shift and an increase in the amplitude of the resonant peak in the EM conductance spectrum of the PZT. An increase in the substrate compliance produces a decrease in the resonant frequency and an increase in the amplitude of the resonant peak. Changes in the resonant peak in the conductance spectrum induced by increasing substrate stress are of a significant magnitude when compared with the changes induced by damage. In the early stages of damage associated with distributed microcracking, the counteracting influences of increasing level of damage and increasing stress on the resonant peak result in no shift in frequency for measurements under applied load. There is however an increase in the amplitude of the resonance peak. When the applied stress is removed, there is a net decrease in frequency resulting from damage in the form of distributed microcracks. Measures of changes in the resonant peak based on root mean square deviation (RMSD), do not show any observable change when measurements are performed under applied loading. There is a consistent increase in RMSD values and frequency shift with increasing damage when the applied stress is removed. The centroidal measure of the normalized frequency spectrum reflects changes in substrate stress. At higher applied stress levels, there is a nonlinear increase in damage, leading to localization and cracking. The influence of damage is dominant in this region and significant changes are obtained in the RMSD values in both loaded and unloaded conditions.

  18. PZT压电纤维的制备及性能研究%Study on the Preparation and Properties of PZT Ceramic Fibers

    Institute of Scientific and Technical Information of China (English)

    杨杰; 刘兴钊

    2009-01-01

    以溶胶-凝胶(Sol-Gel)工艺制备的PZT陶瓷粉为原料,采用氧化物粉末装管法制备PZT压电陶瓷纤维.SEM分析显示,该陶瓷纤维呈圆柱型形貌,直径约为250 μm.分析了不同烧结温度下PZT陶瓷纤维的断面微结构及Pb含量变化,得出PZT陶瓷纤维的最佳烧结温度为1 000 ℃.XRD分析表明,此温度下烧结的陶瓷纤维呈单一的钙钛矿结构.实验结果表明,采用氧化物粉末装管法制备的陶瓷纤维大小均匀,结构致密,具有高长径比,克服了传统工艺不能制备结构致密的长纤维的缺陷.%Using the PZT ceramic powder prepared by Sol-Gel method as the raw material, the PZT piezoelectric ceramic fibers have been prepaared by using the Oxide Powder in Tube(OPTT)procedure.The SEM morphology showed that the PZT ceramic fibers had a cylindrical morphology with a diameter of about 250 μm.The sectional micro-structure and the content of Pb of the PZT ceramic fiber were analyzed at different sintering temperature. The result showed that the optimal sintering termperature of the PZT ceramic fiber was 1 000 ℃.The X-ray diffraction patterns showed that the ceramic fibers were pure perovskite structure.Compared with conventional fabrication process,PZT ceramic fibers prepared by the OPIT method have the advantage of dense ,uniform and high height-to-width ratio.

  19. Feasibility of Using PZT Actuators to Study the Dynamic Behavior of a Rotating Disk due to Rotor-Stator Interaction

    Directory of Open Access Journals (Sweden)

    Alexandre Presas

    2014-07-01

    Full Text Available In this paper, PZT actuators are used to study the dynamic behavior of a rotating disk structure due to rotor-stator interaction excitation. The disk is studied with two different surrounding fluids—air and water. The study has been performed analytically and validated experimentally. For the theoretical analysis, the natural frequencies and the associated mode shapes of the rotating disk in air and water are obtained with the Kirchhoff-Love thin plate theory coupled with the interaction with the surrounding fluid. A model for the Rotor Stator Interaction that occurs in many rotating disk-like parts of turbomachinery such as compressors, hydraulic runners or alternators is presented. The dynamic behavior of the rotating disk due to this excitation is deduced. For the experimental analysis a test rig has been developed. It consists of a stainless steel disk (r = 198 mm and h = 8 mm connected to a variable speed motor. Excitation and response are measured from the rotating system. For the rotating excitation four piezoelectric patches have been used. Calibrating the piezoelectric patches in amplitude and phase, different rotating excitation patterns are applied on the rotating disk in air and in water. Results show the feasibility of using PZT to control the response of the disk due to a rotor-stator interaction.

  20. Effects of Sr2+substitution on the structural, dielectric, and piezoelectric properties of PZT-PMN ceramics

    Institute of Scientific and Technical Information of China (English)

    Arvind Kumar; S.K. Mishra

    2014-01-01

    This study described the structural, dielectric, and piezoelectric behavior of Pb1-xSrx[(Zr0.52Ti0.48)0.95(Mn1/3Nb2/3)0.05]O3 ceramics (PSZT-PMN, x=0, 0.025, 0.050, and 0.075), prepared by a semi-wet route. X-ray diffraction, dielectric, and piezoelectric investigations were carried out to analyze the crystal structure. The relative dielectric constant and dielectric loss were both calculated as the functions of temperature. The room-temperature dielectric constant reaches a maximum for a Sr2+-modified PZT-PMN ceramic with an x value of 0.050, which corresponds to the morphotropic phase boundary (MPB). Raman spectroscopy studies also confirm the existence of this MPB for x=0.050. The piezoelectric strain coefficients (d33) value shows a maximum response for this composition. In addition, the phase transition temperature decreases significantly when the Sr2+concentration increases in the PZT-PMN ceramics.

  1. Feasibility of using PZT actuators to study the dynamic behavior of a rotating disk due to rotor-stator interaction.

    Science.gov (United States)

    Presas, Alexandre; Egusquiza, Eduard; Valero, Carme; Valentin, David; Seidel, Ulrich

    2014-07-07

    In this paper, PZT actuators are used to study the dynamic behavior of a rotating disk structure due to rotor-stator interaction excitation. The disk is studied with two different surrounding fluids-air and water. The study has been performed analytically and validated experimentally. For the theoretical analysis, the natural frequencies and the associated mode shapes of the rotating disk in air and water are obtained with the Kirchhoff-Love thin plate theory coupled with the interaction with the surrounding fluid. A model for the Rotor Stator Interaction that occurs in many rotating disk-like parts of turbomachinery such as compressors, hydraulic runners or alternators is presented. The dynamic behavior of the rotating disk due to this excitation is deduced. For the experimental analysis a test rig has been developed. It consists of a stainless steel disk (r = 198 mm and h = 8 mm) connected to a variable speed motor. Excitation and response are measured from the rotating system. For the rotating excitation four piezoelectric patches have been used. Calibrating the piezoelectric patches in amplitude and phase, different rotating excitation patterns are applied on the rotating disk in air and in water. Results show the feasibility of using PZT to control the response of the disk due to a rotor-stator interaction.

  2. Shear piezoelectric coefficients of PZT, LiNbO3 and PMN-PT at cryogenic temperatures

    Science.gov (United States)

    Bukhari, Syed; Islam, Md; Haziot, Ariel; Beamish, John

    2014-12-01

    Piezoelectric transducers are used to detect stress and to generate nanometer scale displacements but their piezoelectric coefficients decrease with temperature, limiting their performance in cryogenic applications. We have developed a capacitive technique and directly measured the temperature dependence of the shear coefficient d15 for ceramic lead zirconium titanate (PZT), 41° X-cut lithium niobate (LiNbO3) and single crystal lead magnesium niobium-lead titanate (PMN-PT). In PZT, d15 decreases nearly linearly with temperature, dropping by factor of about 4 by 1.3 K. LiNbO3 has the smallest room temperature d15, but its value decreased by only 6% at the lowest temperatures. PMN-PT had the largest value of d15 at room temperature (2.9 × 10-9 m/V, about 45 times larger than for LiNbO3) but it decreased rapidly below 75 K; at 1.3 K, d15 was only about 8% of its room temperature value.

  3. Screen-printed piezoelectric shoe-insole energy harvester using an improved flexible PZT-polymer composites

    Science.gov (United States)

    Almusallam, A.; Torah, R. N.; Zhu, D.; Tudor, M. J.; Beeby, S. P.

    2013-12-01

    This paper reports improved screen-printed piezoelectric composites that can be printed on fabrics or flexible substrates. The materials are flexible and are processed at lower temperature (130°C). One main PZT particle size (2μm) was mixed separately with smaller piezoelectric particles (0.1, 0.3 and 0.8μm) with different weight ratios to investigate the piezoelectric property d33. The blended PZT powder was then mixed with 40% polymer binder and printed on Alumina substrates. The applied poling field, temperature and time were 8MV/m, 160°C and 10min, respectively. The optimum material gives a d33 of 36pC/N with particle sizes of 2μm and 0.8μm and mixed percentages of 82% and 18%, respectively. A screen-printed piezoelectric shoe-insoles (PSI) has been developed as a self-powered force mapping sensor. The PSI was simulated, fabricated and tested. ANSYS results show that one element of PSI sole can produce an open- circuit voltage of 3V when a human of average weight of 70kg makes a gait strike. Experimental results show that one element produced 2V which is less than the simulated results because of the reduction of poling field for the practical device.

  4. Enhancing the dielectric property of 0.69PZT-0.31PZNN thick films by optimizing the poling condition

    Science.gov (United States)

    Song, Daniel; Woo, Min Sik; Ahn, Jung Hwan; Sung, Tae Hyun

    2015-05-01

    We investigated how the applied electric-field's magnitude and the poling time affected, respectively, the dielectric property and the microstructure of piezoelectric lead zirconate titanate/lead zirconate nickel niobate (PZT-PZNN) thick films in order to apply the films to piezoelectric energy harvesters. Several 300-µm-thick, 10 × 10-mm2 PZT-PZNN squares were tape cast, laminated, sintered, and poled under 2-, 4-, 6-, 10-, 14-, and 15-kV/mm electric fields for 30 min. The 10-kV/mm electric field produced the highest d 33 × g 33 without mechanically damaging the sample. Further, samples were sintered at 950, 1000, and 1020 °C and subsequently poled at 10 kV/mm (previously determined as the magnitude of the optimal poling electric field) for 15, 30, 60, 120, and 240 min to investigate how the poling time affected the piezoelectric ceramic's microstructure. The optimal poling time for all the sintered samples was 60 min. Further, the piezoelectric ceramics composed of small grains and poled longer than 60 min showed higher dielectric constants. However, those composed of large grains and poled for times shorter than 60 min showed higher dielectric constants because the element mobility of the piezoelectric ceramics increased with increasing poling time.

  5. Low Temperature Processing of Nanocrystalline Lead Zirconate Titanate (PZT) Thick Films and Ceramics by a Modified Sol-Gel Route

    Science.gov (United States)

    Zhu, Weiguang; Wang, Zhihong; Zhao, Changlei; Tan, Ooi Kiang; Hng, Huey Hoon

    2002-11-01

    Dispersing fine particles into a sol-gel matrix is a promising process to get a thick 0-3 composite coating layer. In this paper, we have further improved this modified sol-gel process by nanocrystalline composite technique to realize the low temperature annealing. Dense Pb(Zr, Ti)O3 (PZT) thick films of 10 to 50 μm in thickness have been obtained on the platinum-coated silicon substrates by spin-coating at sintering temperature of 600-700°C and fully developed submicron-sized grains have been demonstrated in screen-printing piezoelectric films on alumina substrates at sintering temperature of 700-800°C. The dependence of various properties such as microstructure, crystallization, ferroelectric and dielectric properties of such made thick films on the processing parameters have been investigated. For a 10 μm-thick film spin-coated on silicon wafer, the dielectric loss and relative permittivity are 0.010 and 1024, respectively, at 1 kHz. The remanent polarization (Pr) and the coercive field (Ec) are 13.6 μC/cm2 and 34.5 kV/cm, respectively. Obviously, such made thick film has comparable properties with bulk PZT ceramic. This novel technique can be extensively used in sol-gel, screen-printing, tape-casting, even in traditional ceramic process to reduce the process temperature.

  6. Síntese e caracterização da cerâmica PZT dopada com íons bário Synthesis and characterization of barium-doped PZT ceramics

    Directory of Open Access Journals (Sweden)

    G. Gasparotto

    2003-04-01

    Full Text Available Pós de titanato zirconato de chumbo (PZT puros e dopados com bário foram obtidos pelo método de precursores poliméricos, conformados uniaxialmente, na forma de cilindros, utilizando 15 MPa, e prensados isostaticamente à 210MPa. Com o objetivo de estudar o comportamento de sinterização os compactos foram divididos em dois lotes. Sendo um sinterizado em um forno acoplado a um dilatômetro até a temperatura de 1300 °C e o outro sinterizado em forno tipo mufla, em sistema fechado, na temperatura de 1100 °C por 4 horas. Verificou-se que a adição do íon bário influencia na cinética de sinterização, na densificação final, na microestrutura e nas propriedades elétricas da cerâmica. A adição de bário aumenta a concentração da fase tetragonal no PZT, em função da substituição do chumbo por bário na rede perovskita. As amostras dopadas com concentrações maiores que 5,0 mol % em bário apresentaram segregação de PbO no contorno de grão, inibindo seu crescimento.Pure and barium doped lead zirconate titanate powders were obtained by the polymeric precursor method, uniaxially conformed in cylinders form using 15 MPa and pressing isostatically at 210 MPa. In order to study the sintering behaviour, the compacts were divided in two parts. One part was sintered in a dilatometer furnace till 1300 °C and the other one sintered in muffle furnace in the temperature of 1100 °C for 4 hours. It was verified that the addition of barium influences on the sintering kinetics, on the final density, microstructure and electric properties of the ceramics. The addition of barium increases the concentration of the tetragonal phase of PZT due to the substitution of lead by barium in the perovskite lattice. The samples doped with barium concentrations higher than 5.0 mol % leads to the segregation of PbO in the grain boundary, inhibiting grain growth.

  7. The effect of calcining temperature on the properties of 0-3 piezoelectric composites of PZT and a liquid crystalline thermosetting polymer

    NARCIS (Netherlands)

    Ende, D.A. van den; Groen, W.A.; Zwaag, S. van der

    2011-01-01

    We report on the optimisation of a recently developed high performance 0-3 piezoelectric composite comprising of the piezoelectric Lead Zirconate Titanate (PZT) powder and a liquid crystalline thermosetting matrix polymer (LCT). The matrix polymer is a liquid crystalline polymer comprising of an HBA

  8. Characterization of PZT Capacitor Structures with Various Electrode Materials Processed In-Situ Using AN Automated, Rotating Elemental Target, Ion Beam Deposition System

    Science.gov (United States)

    Gifford, Kenneth Douglas

    Ferroelectric thin film capacitor structures containing lead zirconate titanate (PZT) as the dielectric, with the chemical formula Pb(rm Zr_{x }Ti_{1-x})O_3, were synthesized in-situ with an automated ion beam sputter deposition system. Platinum (Pt), conductive ruthenium oxide (RuO_2), and two types of Pt-RuO_2 hybrid electrodes were used as the electrode materials. The capacitor structures are characterized in terms of microstructure and electrical characteristics. Reduction or elimination of non-ferroelectric phases, that nucleate during PZT processing on Pt/TiO _2/MgO and RuO_2/MgO substrates, is achieved by reducing the thickness of the individually deposited layers and by interposing a buffer layer (~100-200A) of PbTiO _3 (PT) between the bottom electrode and the PZT film. Capacitor structures containing a Pt electrode exhibit poor fatigue resistance, irregardless of the PZT microstructure or the use of a PT buffer layer. From these results, and results from similar capacitors synthesized with sol-gel and laser ablation, PZT-based capacitor structures containing Pt electrodes are considered to be unsuitable for use in memory devices. Using a PT buffer layer, in capacitor structures containing RuO_2 top and bottom electrodes and polycrystalline, highly (101) oriented PZT, reduces or eliminates the nucleation of zirconium-titanium oxide, non-ferroelectric species at the bottom electrode interface during processing. This results in good fatigue resistance up to ~2times10^ {10} switching cycles. DC leakage current density vs. time measurements follow the Curie-von Schweidler law, J(t) ~ t^ {rm -n}. Identification of the high electric field current conduction mechanism is inconclusive. The good fatigue resistance, low dc leakage current, and excellent retention, qualifies the use of these capacitor structures in non-volatile random access (NVRAM) and dynamic random access (DRAM) memory devices. Excellent fatigue resistance (10% loss in remanent polarization up to

  9. Generation of electrical energy using lead zirconate titanate (PZT-5A) piezoelectric material: Analytical, numerical and experimental verifications

    Energy Technology Data Exchange (ETDEWEB)

    Butt, Zubair; Ahmad, Nasir [Dept. of Mechanical, Mechatronics and Manufacturing Engineering, UET Lahore, Faisalabad Campus, Lahore (Pakistan); Pasha, Riffat Asim; Qayyum, Faisal; Anjum, Zeeshan [Dept. of Mechanical Engineering, University of Engineering and Technology, Taxila (Pakistan); Elahi, Hassan [Northwestern Polytechnical University, Xian (China)

    2016-08-15

    Energy harvesting is the process of attaining energy from the external sources and transforming it into usable electrical energy. An analytical model of piezoelectric energy harvester has been developed to determine the output voltage across an electrical circuit when it is forced to undergo a base excitation. This model gives an easy approach to design and investigate the behavior of piezoelectric material. Numerical simulations have been carried out to determine the effect of frequency and loading on a Lead zirconate titanate (PZT-5A) piezoelectric material. It has been observed that the output voltage from the harvester increases when loading increases whereas its resonance frequency decreases. The analytical results were found to be in good agreement with the experimental and numerical simulation results.

  10. PZT/P(VDF-HFP) 0-3 composites as solvent-cast thin films: preparation, structure and piezoelectric properties

    Energy Technology Data Exchange (ETDEWEB)

    Wegener, Michael; Arlt, Kristin [Functional Polymer Systems, Fraunhofer Institute for Applied Polymer Research (IAP), Geiselbergstrasse 69, 14476 Potsdam-Golm (Germany)], E-mail: michael.wegener@iap.fraunhofer.de

    2008-08-21

    Composite films of lead zirconate titanate (PZT) and poly(vinylidene fluoride-hexafluoropropylene) (P(VDF-HFP)) were prepared as 100 {mu}m thin films by solvent casting. Within the 0-3 composites, the ceramic-volume fraction was varied between 0.19 and 0.65, which yielded films with different structural and dielectric properties. These influenced the piezoelectric properties of the composite films found after electric poling, which was performed here at room temperature. The piezoelectric activity, with a maximum piezoelectric coefficient of 11 pC N{sup -1} in the film-thickness direction, originates from the polarization of the embedded ceramic particles as proved by poling experiments in corona discharges as well as in direct contact.

  11. A Crystallization Study of Nanocrystalline PZT 53/47Granular Arrays Using a Sol-Gel Based Precursor

    Institute of Scientific and Technical Information of China (English)

    A. Suárez-Gómez; J.M. Saniger-Blesa; F. Calderón-Pi(n)ar

    2011-01-01

    In this work, we intend to perform a detailed study on the crystallization process of PZT 53/47 nanostructured powders by starting out with an amorphous precursor synthesized by a sol-gel based solution. Our interests also lie in the feasibility for controlling the average grain size of the final structure in the submicron range on an ab initio basis. Purposely, Fourier transform infrared spectroscopy (FT-IR), Raman (Stokes and Anti-Stokes), X-ray diffraction (XRD) and scanning electron microscopy (SEM) are used to examine the microstructural characteristics based on previously reported differential thermal analysis/thermal gravimetric analysis (DTA/TGA) data. The results show a crystallization temperature of 800℃ to attain pure perovskite phase with excellent morphological quality, average grain size <DG>< 300 nm and with average crystallite size <DC><15 nm.

  12. Effect of temperature and loading on output voltage of lead zirconate titanate (PZT-5A) piezoelectric energy harvester

    Science.gov (United States)

    Butt, Z.; Pasha, R. A.

    2016-08-01

    Energy harvesting is the process of acquiring energy from the external sources and then further used to drive any system. Piezoelectric material was operated at various temperature but the characterization of the material mostly performed at room temperature. The depolarization in piezoelectric material occurs when the material is heated to its curie temperature and when mechanical stresses are high to disturb the properties of the material. The aim of this paper is to study the performance of lead zirconate titanate (PZT-5A) piezoelectric material under various temperatures and loading conditions. The output voltage of piezoelectric material decreases with increase of temperature. It was found that output voltage from the harvester increases when loading increases while its temperature decreases.

  13. Efecto del Cross-talk en la respuesta de un Transductor Ultrasónico tipo PZT

    OpenAIRE

    Sánchez Domínguez, Israel

    2014-01-01

    El presente trabajo de tesis investiga el efecto del fenómeno conocido como “Cross-talk” generado por el modo lateral de vibración, en la respuesta de un transductor ultrasónico formado por un arreglo de elementos piezoeléctricos tipo PZT (Zircanato Titanato de Plomo), la investigación se lleva a cabo desde el punto de vista de la naturaleza física de este efecto, así como de los parámetros asociados al mismo, así como un análisis del efecto del “Cross-talk” en la respuesta del transductor, f...

  14. Acoustic Emission Detection of Macro-Cracks on Engraving Tool Steel Inserts during the Injection Molding Cycle Using PZT Sensors

    Directory of Open Access Journals (Sweden)

    Aleš Hančič

    2013-05-01

    Full Text Available This paper presents an improved monitoring system for the failure detection of engraving tool steel inserts during the injection molding cycle. This system uses acoustic emission PZT sensors mounted through acoustic waveguides on the engraving insert. We were thus able to clearly distinguish the defect through measured AE signals. Two engraving tool steel inserts were tested during the production of standard test specimens, each under the same processing conditions. By closely comparing the captured AE signals on both engraving inserts during the filling and packing stages, we were able to detect the presence of macro-cracks on one engraving insert. Gabor wavelet analysis was used for closer examination of the captured AE signals’ peak amplitudes during the filling and packing stages. The obtained results revealed that such a system could be used successfully as an improved tool for monitoring the integrity of an injection molding process.

  15. Estimation of strain from piezoelectric effect and domain switching in morphotropic PZT by combined analysis of macroscopic strain measurements and synchrotron X-ray data

    Energy Technology Data Exchange (ETDEWEB)

    Kungl, Hans [Institute of Ceramics in Mechanical Engineering, University of Karlsruhe, Haid-und-Neu-Str. 7, 76131 Karlsruhe (Germany)]. E-mail: hans.kungl@ikm.uni-karlsruhe.de; Theissmann, Ralf [Materials Science, Darmstadt University of Technology (Germany); Knapp, Michael [Materials Science, Darmstadt University of Technology (Germany); Baehtz, Carsten [Materials Science, Darmstadt University of Technology (Germany); Fuess, Hartmut [Materials Science, Darmstadt University of Technology (Germany); Wagner, Susanne [Institute of Ceramics in Mechanical Engineering, University of Karlsruhe, Haid-und-Neu-Str. 7, 76131 Karlsruhe (Germany); Fett, Theo [Institute of Ceramics in Mechanical Engineering, University of Karlsruhe, Haid-und-Neu-Str. 7, 76131 Karlsruhe (Germany); Hoffmann, Michael J. [Institute of Ceramics in Mechanical Engineering, University of Karlsruhe, Haid-und-Neu-Str. 7, 76131 Karlsruhe (Germany)

    2007-04-15

    Morphotropic PZT ceramics are State of the art materials for ferroelectric actuators. Essential performance parameters for these materials are strain and hysteresis. On a microscopic scale the strain provided by an electric field is due to two different mechanisms. The piezoelectric effect causes an elongation of the unit cells, whereas domain switching changes their crystallographic orientation by aligning the polarization axis towards the field direction. A method is outlined to estimate the contribution of the two mechanisms to total strain by combining macroscopic strain measurements and X-ray diffraction (XRD) data. Results from macroscopic measurements of remanent and unipolar strain with the corresponding data on texture, derived from in situ synchrotron radiation XRD patterns, are analyzed and evaluated by a semi-empirical approach. The method was applied to six morphotropic, LaSr doped PZT materials of different Zr/Ti ratios. Results are discussed with respect to the differences between the materials.

  16. Ferroelectricity, Piezoelectricity, and Dielectricity of 0.06PMnN-0.94PZT(45/55 Thin Film on Silicon Substrate

    Directory of Open Access Journals (Sweden)

    Tao Zhang

    2015-01-01

    Full Text Available The high piezoelectricity and high quality factor ferroelectric thin films are important for electromechanical applications especially the micro electromechanical system (MEMS. The ternary compound ferroelectric thin films 0.06Pb(Mn1/3, Nb2/3O3 + 0.94Pb(Zr0.45, Ti0.55O3 (0.06PMnN-0.94PZT(45/55 were deposited on silicon(100 substrates by RF magnetron sputtering method considering that Mn and Nb doping will improve PZT properties in this research. For comparison, nondoped PZT(45/55 films were also deposited. The results show that both of thin films show polycrystal structures with the main (111 and (101 orientations. The transverse piezoelectric coefficients are e31,eff=−4.03 C/m2 and e31,eff=-3.5 C/m2, respectively. These thin films exhibit classical ferroelectricity, in which the coercive electric field intensities are 2Ec=147.31 kV/cm and 2Ec=135.44 kV/cm, and the saturation polarization Ps=30.86 μC/cm2 and Ps=17.74 μC/cm2, and the remnant polarization Pr=20.44 μC/cm2 and Pr=9.87 μC/cm2, respectively. Moreover, the dielectric constants and loss are εr=681 and D=5% and εr=537 and D=4.3%, respectively. In conclusion, 0.06PMnN-0.94PZT(45/55 thin films act better than nondoped films, even though their dielectric constants are higher. Their excellent ferroelectricity, piezoelectricity, and high power and energy storage property, especially the easy fabrication, integration realizable, and potentially high quality factor, make this kind of thin films available for the realistic applications.

  17. In situ Barely Visible Impact Damage detection and localization for composite structures using surface mounted and embedded PZT transducers: A comparative study

    Science.gov (United States)

    Dziendzikowski, M.; Kurnyta, A.; Dragan, K.; Klysz, S.; Leski, A.

    2016-10-01

    Application of guided waves excited by a network of PZT transducers integrated with a given structure is one of the promising approaches to Structural Health Monitoring (SHM). The performance of a SHM system based on PZT network is rooted in two distinct areas of the technology development, that is the hardware and the signal analysis. The first includes the type of transducers used to built a network and the way of their integration with a monitored structure. For composites, besides the possibility of the transducers attachment to a surface of an element, also embedding of PZTs into their internal structure is available. In the article Barely Visible Impact Damage (BVID) detection capabilities as well as selected physical properties of the embedded and surface mounted PZT transducers are compared in broad frequency range of the excitation. Among the compared parameters are the impedance and capacitance spectra up to 600 kHz. The damage detection capabilities are compared in the range 100-350 kHz. In addition to purely qualitative detection of damages a new algorithm of their localization is proposed and compared between the embedded and surface attached transducers for the frequency optimal to detect BVIDs.

  18. Accurate Determination of the Frequency Response Function of Submerged and Confined Structures by Using PZT-Patches†.

    Science.gov (United States)

    Presas, Alexandre; Valentin, David; Egusquiza, Eduard; Valero, Carme; Egusquiza, Mònica; Bossio, Matias

    2017-03-22

    To accurately determine the dynamic response of a structure is of relevant interest in many engineering applications. Particularly, it is of paramount importance to determine the Frequency Response Function (FRF) for structures subjected to dynamic loads in order to avoid resonance and fatigue problems that can drastically reduce their useful life. One challenging case is the experimental determination of the FRF of submerged and confined structures, such as hydraulic turbines, which are greatly affected by dynamic problems as reported in many cases in the past. The utilization of classical and calibrated exciters such as instrumented hammers or shakers to determine the FRF in such structures can be very complex due to the confinement of the structure and because their use can disturb the boundary conditions affecting the experimental results. For such cases, Piezoelectric Patches (PZTs), which are very light, thin and small, could be a very good option. Nevertheless, the main drawback of these exciters is that the calibration as dynamic force transducers (relationship voltage/force) has not been successfully obtained in the past. Therefore, in this paper, a method to accurately determine the FRF of submerged and confined structures by using PZTs is developed and validated. The method consists of experimentally determining some characteristic parameters that define the FRF, with an uncalibrated PZT exciting the structure. These parameters, which have been experimentally determined, are then introduced in a validated numerical model of the tested structure. In this way, the FRF of the structure can be estimated with good accuracy. With respect to previous studies, where only the natural frequencies and mode shapes were considered, this paper discuss and experimentally proves the best excitation characteristic to obtain also the damping ratios and proposes a procedure to fully determine the FRF. The method proposed here has been validated for the structure vibrating

  19. Accurate Determination of the Frequency Response Function of Submerged and Confined Structures by Using PZT-Patches †

    Science.gov (United States)

    Presas, Alexandre; Valentin, David; Egusquiza, Eduard; Valero, Carme; Egusquiza, Mònica; Bossio, Matias

    2017-01-01

    To accurately determine the dynamic response of a structure is of relevant interest in many engineering applications. Particularly, it is of paramount importance to determine the Frequency Response Function (FRF) for structures subjected to dynamic loads in order to avoid resonance and fatigue problems that can drastically reduce their useful life. One challenging case is the experimental determination of the FRF of submerged and confined structures, such as hydraulic turbines, which are greatly affected by dynamic problems as reported in many cases in the past. The utilization of classical and calibrated exciters such as instrumented hammers or shakers to determine the FRF in such structures can be very complex due to the confinement of the structure and because their use can disturb the boundary conditions affecting the experimental results. For such cases, Piezoelectric Patches (PZTs), which are very light, thin and small, could be a very good option. Nevertheless, the main drawback of these exciters is that the calibration as dynamic force transducers (relationship voltage/force) has not been successfully obtained in the past. Therefore, in this paper, a method to accurately determine the FRF of submerged and confined structures by using PZTs is developed and validated. The method consists of experimentally determining some characteristic parameters that define the FRF, with an uncalibrated PZT exciting the structure. These parameters, which have been experimentally determined, are then introduced in a validated numerical model of the tested structure. In this way, the FRF of the structure can be estimated with good accuracy. With respect to previous studies, where only the natural frequencies and mode shapes were considered, this paper discuss and experimentally proves the best excitation characteristic to obtain also the damping ratios and proposes a procedure to fully determine the FRF. The method proposed here has been validated for the structure vibrating

  20. Chem-prep PZT95/5 for neutron generator applications : the effect of pore former type and density on the depoling behavior of chemically prepared PZT 95/5 ceramics.

    Energy Technology Data Exchange (ETDEWEB)

    Lockwood, Steven John; Scofield, Timothy W.; Yang, Pin; Voigt, James A.; Tuttle, Bruce Andrew; Moore, Roger Howard

    2003-10-01

    The hydrostatically induced ferroelectric(FE)-to-antiferroelectric(AFE) phase transformation for chemically prepared niobium modified PZT 95/5 ceramics was studied as a function of density and pore former type (Lucite or Avicel). Special attention was placed on the effect of different pore formers on the charge release behavior associated with the FE-to-AFE phase transformation. Within the same density range (7.26 g/cm3 to 7.44 g/cm3), results showed that ceramics prepared with Lucite pore former exhibit a higher bulk modulus and a sharper polarization release behavior than those prepared with Avicel. In addition, the average transformation pressure was 10.7% greater and the amount of polarization released was 2.1% higher for ceramics with Lucite pore former. The increased transformation pressure was attributed to the increase of bulk modulus associated with Lucite pore former. Data indicated that a minimum volumetric transformational strain of -0.42% was required to trigger the hydrostatically induced FE-to-AFE phase transformation. This work has important implications for increasing the high temperature charge output for neutron generator power supply units.

  1. Evaluation of the effect of porosity and substrate on the piezoelectric behaviour of thick-film PZT elements

    Energy Technology Data Exchange (ETDEWEB)

    Gwirc, S N [Instituto Nacional de TecnologIa Industrial, Electronica e Informatica, CC 157, B1650WAB San Martin, Buenos Aires (Argentina); Negreira, C A [Instituto de Fisica, Laboratorio de Acustica Ultrasonora, Facultad de Ciencias, Igua 4225, 11400 Montevideo (Uruguay)

    2006-10-07

    This work presents a method to establish the elastic and piezoelectric constants of a thick film screen printed PZT composite over an alumina substrate. The calculus procedure uses as input data the parameters from the bulk material because it is basically the same component of which the thick film paste is manufactured. We also need to know frequencies of resonance and anti-resonance as well as the permittivity and density of the film in a poled disc sample. This method takes into account three factors: the additional components such as the glass frit, porosity of the film caused by the low temperature sinter process and the film clamping to the substrate. Each one of these factors reduces the piezoelectric efficiency by a different amount and, consequently, the measured values of the constants. The results obtained in this way are compared with experimental measurements of the effective piezoelectric charge constant d{sub 33} and permittivity with good agreement. Small discrepancies could be explained mainly due to lack of homogeneity in glass as well as in pore distribution.

  2. Active vibration control of a composite wing model using PZT sensors/actuators and virtex: 4 FPGAs

    Science.gov (United States)

    Prakash, Shashikala; Venkatasubramanyam, D. V.; Krishnan, Bharath; Pavate, Aravind; Kabra, Hemant

    2009-07-01

    The reduction of vibration in Aircraft/Aerospace structures as well as helicopter fuselage is becoming increasingly important. A traditional approach to vibration control uses passive techniques which are relatively large, costly and ineffective at low frequencies. Active Vibration Control (AVC), apart from having benefits in size, weight, volume and cost, efficiently attenuates low frequency vibration. Hitherto this was being achieved using high speed Digital Signal Processors (DSPs). But the throughput requirements of general purpose DSPs have increased very much and the Field Programmable Gate Arrays (FPGAs) have emerged as an alternative. The silicon resources of an FPGA lead to staggering performance gains i.e. they are 100 times faster than DSPs. In the present paper Active Vibration Control of a Composite Research Wing Model is investigated using Piezo electric patches as sensors and PZT bimorph actuators collocated on the bottom surface as secondary actuators. Attempt has been made to realize the State - of - the - Art Active Vibration Controller using the Xilinx System Generator on VIRTEX - 4 FPGA. The control has been achieved by implementing the Filtered-X Least Mean Square (FXLMS) based adaptive filter on the FPGA. Single channel real time control has been successfully implemented & tested on the composite research wing model.

  3. All-thin-film PZT/FeGa Multiferroic Cantilevers and Their Applications in Switching Devices and Parametric Amplification

    Science.gov (United States)

    Wang, Yi; Onuta, Tiberiu-Dan; Long, Chris; Lofland, Samuel; Takeuchi, Ichiro

    2014-03-01

    We are investigating the characteristics of microfabricated PZT/FeGa multiferroic cantilevers. The cantilevers can be driven by AC or DC magnetic and electric field, and the device response can be read off as a piezo-induced voltage. We can use the multiple input parameters to operate the devices in a variety of manners for different applications. They include electromagnetic energy harvesting, pulse triggered nonlinear memory devices, and parametrically amplified ME sensors. Due to the competition of anisotropy and Zeeman energies, the mechanical resonant frequency of the cantilevers was found to follow a hysteresis behavior with DC bias magnetic field applied in the cantilever easy axis. We can also control and tune the occurrence of nonlinear bifurcation in the frequency spectrum. The resulting hysteresis in the frequency spectrum can be used to make switching devices, where the input can be DC electric and magnetic fields, as well as pulses of AC fields. We have also demonstrated parametric pumping of the response from an AC magnetic field using frequency-doubled AC electric field. The enhanced equivalent ME coefficient is as high as 10 million V/(cm*Oe), when the pumping voltage is very close to a threshold voltage. The quality factor also increases from 2000 to 80000 with pumping.

  4. Simulation of the fluidic features for diffuser/nozzle involved in a PZT-based valveless micropump

    Institute of Scientific and Technical Information of China (English)

    HouWensheng; Zheng Xiaolin; Biswajit Das; Jiang Yingtao; Qian Shizhi; Wu Xiaoying; Zheng Zhigao

    2008-01-01

    PZT-based valveless micropump is a microactuator that can be used for controlling and delivering tiny amounts of fluids, and diffuser/nozzle plays an important role when this type of micropump drives the fluid flowing along a specific direction. In this paper, a numerical model of micropump has been proposed, and the fluidic properties of diffuser/nozzle have been simulated with ANSYS. With the method of finite-element analysis, the increased pressure drop between inlet and outlet of diffuser/nozzle induces the increment of flow rate in both diffuser and nozzle simultaneously, but the increasing rate of diffuser is faster than that of nozzle. The L/R, ratio of L (length of cone pipe) and R (radius of minimal cross section of cone pipe) plays an important role in fluidic performance of diffuser and nozzle as well, and the mean flow rate will decrease with increment of L/R. The mean flow rate reaches its peak value when L/R with the value of 10 regardless the divergence angle of diffuser or nozzle. The simulation results indicate that the fluidic properties of diffuser/nozzle can be defined by its geometric structure, and accordingly determine the efficiency of micropump.

  5. A Prototype PZT Matrix Transducer With Low-Power Integrated Receive ASIC for 3-D Transesophageal Echocardiography.

    Science.gov (United States)

    Chen, Chao; Raghunathan, Shreyas B; Yu, Zili; Shabanimotlagh, Maysam; Chen, Zhao; Chang, Zu-yao; Blaak, Sandra; Prins, Christian; Ponte, Jacco; Noothout, Emile; Vos, Hendrik J; Bosch, Johan G; Verweij, Martin D; de Jong, Nico; Pertijs, Michiel A P

    2016-01-01

    This paper presents the design, fabrication, and experimental evaluation of a prototype lead zirconium titanate (PZT) matrix transducer with an integrated receive ASIC, as a proof of concept for a miniature three-dimensional (3-D) transesophageal echocardiography (TEE) probe. It consists of an array of 9 ×12 piezoelectric elements mounted on the ASIC via an integration scheme that involves direct electrical connections between a bond-pad array on the ASIC and the transducer elements. The ASIC addresses the critical challenge of reducing cable count, and includes front-end amplifiers with adjustable gains and micro-beamformer circuits that locally process and combine echo signals received by the elements of each 3 ×3 subarray. Thus, an order-of-magnitude reduction in the number of receive channels is achieved. Dedicated circuit techniques are employed to meet the strict space and power constraints of TEE probes. The ASIC has been fabricated in a standard 0.18-μm CMOS process and consumes only 0.44 mW/channel. The prototype has been acoustically characterized in a water tank. The ASIC allows the array to be presteered across ±37° while achieving an overall dynamic range of 77 dB. Both the measured characteristics of the individual transducer elements and the performance of the ASIC are in good agreement with expectations, demonstrating the effectiveness of the proposed techniques.

  6. A piezoelectric micro generator worked at low frequency and high acceleration based on PZT and phosphor bronze bonding

    Science.gov (United States)

    Tang, Gang; Yang, Bin; Hou, Cheng; Li, Guimiao; Liu, Jingquan; Chen, Xiang; Yang, Chunsheng

    2016-01-01

    Recently, piezoelectric energy harvesters (PEHs) have been paid a lot of attention by many researchers to convert mechanical energy into electrical and low level vibration. Currently, most of PEHs worked under high frequency and low level vibration. In this paper, we propose a micro cantilever generator based on the bonding of bulk PZT wafer and phosphor bronze, which is fabricated by MEMS technology, such as mechanical chemical thinning and etching. The experimental results show that the open-circuit output voltage, output power and power density of this fabricated prototype are 35 V, 321 μW and 8664 μW cm−3 at the resonant frequency of 100.8 Hz, respectively, when it matches an optimal loading resistance of 140 kΩ under the excitation of 3.0 g acceleration. The fabricated micro generator can obtain the open-circuit stable output voltage of 61.2 V when the vibration acceleration arrives at 7.0 g. Meanwhile, when this device is pasted on the vibrating vacuum pump, the output voltage is about 11 V. It demonstrates that this novel proposed device can scavenge high vibration level energy at low frequency for powering the inertial sensors in internet of things application. PMID:27929139

  7. A piezoelectric micro generator worked at low frequency and high acceleration based on PZT and phosphor bronze bonding

    Science.gov (United States)

    Tang, Gang; Yang, Bin; Hou, Cheng; Li, Guimiao; Liu, Jingquan; Chen, Xiang; Yang, Chunsheng

    2016-12-01

    Recently, piezoelectric energy harvesters (PEHs) have been paid a lot of attention by many researchers to convert mechanical energy into electrical and low level vibration. Currently, most of PEHs worked under high frequency and low level vibration. In this paper, we propose a micro cantilever generator based on the bonding of bulk PZT wafer and phosphor bronze, which is fabricated by MEMS technology, such as mechanical chemical thinning and etching. The experimental results show that the open-circuit output voltage, output power and power density of this fabricated prototype are 35 V, 321 μW and 8664 μW cm-3 at the resonant frequency of 100.8 Hz, respectively, when it matches an optimal loading resistance of 140 kΩ under the excitation of 3.0 g acceleration. The fabricated micro generator can obtain the open-circuit stable output voltage of 61.2 V when the vibration acceleration arrives at 7.0 g. Meanwhile, when this device is pasted on the vibrating vacuum pump, the output voltage is about 11 V. It demonstrates that this novel proposed device can scavenge high vibration level energy at low frequency for powering the inertial sensors in internet of things application.

  8. Effect of Pb content and solution concentration of Pb{sub x}TiO{sub 3} seed layer on (100)-texture and ferroelectric/dielectric behavior of PZT (52/48) thin films

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Jian; Batra, Vaishali; Han, Hui; Kotru, Sushma, E-mail: skotru@eng.ua.edu [Department of Electrical and Computer Engineering, The University of Alabama, Tuscaloosa, Alabama 35487 (United States); Pandey, Raghvendar K. [Ingram School of Engineering, Texas State University, San Marcos, Texas 78666 (United States)

    2015-09-15

    The effect of Pb content and solution concentration of lead titanate (Pb{sub x}TiO{sub 3}) seed layer on the texture and electric properties of Pb{sub 1.1}(Zr{sub 0.52},Ti{sub 0.48})O{sub 3} (PZT) thin films was investigated. A variety of seed layers (y Pb{sub x}TiO{sub 3}) with varying solution concentration (y = 0.02, 0.05, 0.1, and 0.2 M) and Pb content (x = 1.0, 1.05, 1.1, and 1.2) was deposited on Pt/TiO{sub 2}/SiO{sub 2}/Si substrates using chemical-solution deposition method. PZT films were then deposited on these seed layers using the same process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy investigations of the seed layers confirm change in crystal structure with variation in the solution properties. XRD studies of PZT films deposited on seed layers demonstrate that the seed layer helps in enhancing (100)-texture and suppressing (111)-texture. It was observed that PZT films prepared on seed layers with lower solution concentrations results in highly (100)-textured films, which further helps to improve the electric properties. The polarization and dielectric constant of the PZT films were seen to increase while the coercive field decreased with increase in (100)-texture. Irrespective of the seed layer solution concentration, higher Pb content in the seed layer deteriorates the PZT film properties. Ninety-five percent to ninety-six percent (100)-texture was obtained from thin PZT films deposited on seed layers of 0.02 M solution concentration with 1.05 and 1.10 Pb contents, which is higher than the values reported for thick PZT films. Optimization of both Pb content and solution concentration of the seed layer is a promising route to achieve highly (100)-textured PZT films with improved electric properties.

  9. The influence of the point defects on the relaxation processes in a ceramics of the PZT type

    Energy Technology Data Exchange (ETDEWEB)

    Brus, B.; Zachariasz, R.; Ilczuk, J. [Silesian University, Faculty of Computer and Material Science, Department of Material Science, 3 Zeromskiego St., 41-200 Sosnowiec (Poland)

    2004-03-01

    The aim of the present study is twofold: to measure phase transition temperatures and study the relaxation peaks observed in the internal friction for the doped PZT ceramics, with the chemical composition: Pb{sub 0.975}Ba{sub 0.01}Ca{sub 0.01}Sr{sub 0.005}(Zr{sub 0.52}Ti{sub 0.48})O{sub 3}+1.4 wt% Bi{sub 2}O{sub 3}+0.3 wt% GeO. For all measurements, the specimens are rectangular bars (dimensions 30 x 10 x 0,9 mm{sup 3}), some specimens were subjected to polarization by low temperature method (T=423 K, E{sub p}=30 kV/cm, t=30 min) and others were irradiated by {gamma} radiation. Measurements were conducted on a computer-controlled automatic resonant mechanical spectrometer, while heating at different heating rates (1-5 K/min.) and two different frequencies: 930 and 1015 Hz. On the curves Q{sup -1}(T) two maxima of internal friction were observed; P{sub R} at T{sub 1}=382 K (930 Hz), T{sub 1}=386 K (1015 Hz) and P{sub F} at T{sub 2}=638 K (930 and 1015 Hz). The P{sub F} peak originates from the ferroelectric-paraelectric phase transformation; the relaxation peak P{sub R} can be explained in terms of Postnikov's model involving the interaction between mobile point defects and stationary 90 domain walls. The activation parameters of P{sub R} peak deduced from Arrhenius law are respectively: H{sub R}=(0.86{+-}0.02) eV and {tau}{sub oR}=(1.43{+-}0.04) x 10{sup -15} s. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  10. Experimental Determination of Effect of Variable Resistance on Lead ZirconateTitanate (PZT-5A4Eunder various Thermal and Frequency Conditions

    Directory of Open Access Journals (Sweden)

    Hassan Elahi

    2014-12-01

    Full Text Available A specially designed apparatus and circuit working on the principle of inverse piezoelectricity due to the effect of polarization was used to find the relationship between resistance and peak to peak voltage of Lead Zirconate Titanate (PZT-5A4E by shocking it at variable frequencies and at variable resistances under various thermal conditions within Curie temperature limit using equivalent circuit method. It was found that by increasing temperature, peak to peak voltage increases and similarly by increasing frequency, peak to peak voltage decreases and with the increase in resistance peak to peak voltage decreases.

  11. Effects of NaNbO3-Co2O3 Co-additive on the Properties of PZN-PZT Ceramics

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    NaNbO3-Co2O3 co-added PZN-PZT (PZCNNT) ceramics were prepared using conventional solid state reaction. The piezoelectric and dielectric properties were measured. The experimental results show that the addition of 0.3mo1% Co2O3 leads to low dielectric loss (tg δ) in PZCNNT ceramics and the proper addition of NaNbO3 not only improves piezoelectric properties but also decreases intensively dielectric loss and mechanical loss. The optimal ceramic having d33=310 pC/N, kp=0.59, εr=985, tg δ=0.0034, Qm=1380 was obtained.

  12. Asymmetry of Polarization Reversal and Current-Voltage Characteristics of Pt/PZT-Film/Pt:Ti/SiO2/Si-Substrate Structures

    Directory of Open Access Journals (Sweden)

    S. L. Bravina

    2011-01-01

    Full Text Available The characterization of the asymmetries of bipolar charge-voltage and current-voltage loops of polarization reversal and unipolar current-voltage curves for Pt/PZT-film/Pt:Ti/SiO2/Si-substrate systems was performed in the dynamic mode. The asymmetry of local deformation-voltage loops was observed by piezoresponse force microscopy. The comparison of the dependences of introduced asymmetry factors for the bipolar charge-voltage and current-voltage loops and unipolar current-voltage curves on drive voltage indicates the interconnection of ferroelectric and electrical space charge transfer asymmetries.

  13. 柔性PZT复合材料的热释电性质研究%INVESTIGATION OF THE PYROELECTRIE PROPERTIES OF THE FLEXIBLE PZT COMPOSITE

    Institute of Scientific and Technical Information of China (English)

    王国欣

    2001-01-01

    The pyroelectric properties of a flexble composite composed ofNb-doped PZT grains and silica gel are reported.Compared with compact piezoelectric its pyroelectric coefficient is 0.2×10-8~0.28×10-8 C/(cm2·℃),while that of pyroelectric PZT ceramic is 4.9×10-8C/(cm2·℃);the pyroeletric response of the flexible composite is about 5 times greater,than that of the compact ceramic.A method of calculating the pyroelectric coefficient and response of these materials is also described.%研究了由掺铌的钛锆酸铅颗粒与硅橡胶混合物的热释电性质;与一般的致密压电陶瓷相比较,其热释电系数为0.6×10-8~2.0×10-8C/(cm2·℃),而致密PZT陶瓷的热释电系数为4.9×10-8C/(cm2·℃),柔性复合物的热释电响应大约比致密陶瓷大5倍;描述了一种计算这些材料热释电系数和热释电响应的方法.

  14. Effect of Ni/Nb on structure, electrical and ferroelectric properties of 0.5PNN-0.5PZT ceramics

    Directory of Open Access Journals (Sweden)

    Rashmi Gupta

    2015-03-01

    Full Text Available The solid solutions of lead nickel niobate (PNN and lead zirconate titanate (PZT, with general formula 0.5 Pb(NixNb1-xO3-0.5 PZT, where x = 1/3, 1/2 and 2/3 and Zr/Ti = 50/50, were prepared by conventional solid state reaction technique. The perovskite phase formation and morphology were examined by powder X-ray diffraction (XRD and scanning electron microscopy (SEM techniques. From microstructure investigations, the grain size was found to lie in the range of 0.2–1.1 µm. Diffuse phase transition and dielectric relaxation was obtained for all three compositions. The nature of dielectric relaxation was investigated through complex plane Argand plot or Cole-Cole plot. It was found that both grains as well as grain boundary contribute to dielectric relaxation. A direct correlation between the grain size and electrical properties was obtained. The remnant polarization and grain size were found to follow the inverse relationship. The inverse relationship between remnant polarization and grain size was established.

  15. Optimization of a 0.69PZT-0.31PZNN thick film by controlling slurry viscosity and tape-casting blade height

    Science.gov (United States)

    Song, Daniel; Woo, Min Sik; Ahn, Jung Hwan; Sung, Tae Hyun; Kim, Kyoung Bum

    2014-12-01

    We investigated how the viscosities of piezoelectric lead zirconate titanate/lead zirconate nickel niobate (PZT-PZNN) slurry samples affect the laminated-film densities based on various conditions of degassing time for 0, 30, and 60 min. PZT-PZNN slurries with different viscosities were tape casted into green sheets by adjusting the comma blade height to 100, 200, 300, 400, and 500 μm. As a result the slurry viscosity linearly increased with increasing slurry degassing time, and the thickness of the green sheet increased with increasing comma blade height. The density and the dielectric properties of piezoelectric ceramic films with the same thicknesses, but composed of different numbers of layers, were compared. The laminated-film density and the dielectric property d33 × g33 increased with decreasing number of laminated layers. However, when the viscosity of the slurry was too high (degassing time > 60 min) and the comma blade height was too high (comma blade height > 300 μm), the tape-casted green sheet was too thick to have enough time to dry. By controlling the slurry viscosity by adjusting the degassing time and the comma blade height, we were able to optimize the thickness of the green sheet in a tape-casting. The optimal green sheet thickness was < 70 μm, and the number of sheets laminated should be minimized to increase the film's density and dielectric constant.

  16. Optimization of a 0.69PZT-0.31PZNN thick film by controlling slurry viscosity and tape-casting blade height

    Energy Technology Data Exchange (ETDEWEB)

    Song, Daniel; Woo, Minsik; Ahn, Junghwan; Sung, Taehyun [Hanyang University, Seoul (Korea, Republic of); Kim, Kyoungbum [Korea University, Seoul (Korea, Republic of)

    2014-12-15

    We investigated how the viscosities of piezoelectric lead zirconate titanate/lead zirconate nickel niobate (PZT-PZNN) slurry samples affect the laminated-film densities based on various conditions of degassing time for 0, 30, and 60 min. PZT-PZNN slurries with different viscosities were tape casted into green sheets by adjusting the comma blade height to 100, 200, 300, 400, and 500 μm. As a result the slurry viscosity linearly increased with increasing slurry degassing time, and the thickness of the green sheet increased with increasing comma blade height. The density and the dielectric properties of piezoelectric ceramic films with the same thicknesses, but composed of different numbers of layers, were compared. The laminated-film density and the dielectric property d{sub 33} x g{sub 33} increased with decreasing number of laminated layers. However, when the viscosity of the slurry was too high (degassing time > 60 min) and the comma blade height was too high (comma blade height > 300 μm), the tape-casted green sheet was too thick to have enough time to dry. By controlling the slurry viscosity by adjusting the degassing time and the comma blade height, we were able to optimize the thickness of the green sheet in a tape-casting. The optimal green sheet thickness was < 70 μm, and the number of sheets laminated should be minimized to increase the film's density and dielectric constant.

  17. 5 V Compatible Two-Axis PZT Driven MEMS Scanning Mirror with Mechanical Leverage Structure for Miniature LiDAR Application.

    Science.gov (United States)

    Ye, Liangchen; Zhang, Gaofei; You, Zheng

    2017-03-05

    The MEMS (Micro-Electronical Mechanical System) scanning mirror is an optical MEMS device that can scan laser beams across one or two dimensions. MEMS scanning mirrors can be applied in a variety of applications, such as laser display, bio-medical imaging and Light Detection and Ranging (LiDAR). These commercial applications have recently created a great demand for low-driving-voltage and low-power MEMS mirrors. However, no reported two-axis MEMS scanning mirror is available for usage in a universal supplying voltage such as 5 V. In this paper, we present an ultra-low voltage driven two-axis MEMS scanning mirror which is 5 V compatible. In order to realize low voltage and low power, a two-axis MEMS scanning mirror with mechanical leverage driven by PZT (Lead zirconate titanate) ceramic is designed, modeled, fabricated and characterized. To further decrease the power of the MEMS scanning mirror, a new method of impedance matching for PZT ceramic driven by a two-frequency mixed signal is established. As experimental results show, this MEMS scanning mirror reaches a two-axis scanning angle of 41.9° × 40.3° at a total driving voltage of 4.2 Vpp and total power of 16 mW. The effective diameter of reflection of the mirror is 2 mm and the operating frequencies of two-axis scanning are 947.51 Hz and 1464.66 Hz, respectively.

  18. 压电混凝土梁主动健康监测试验%Experimental Research on Active Health Monitoring of PZT Concrete Beam

    Institute of Scientific and Technical Information of China (English)

    蒙彦宇; 阎石; 孙威; 马禄哲; 何彬彬

    2011-01-01

    目的 研究混凝土梁损伤前后信号能量统计分布特征及相对损伤指标,提出一种利用压电智能传感器的混凝土结构损伤统计识别算法,实现试件损伤及破坏过程的动态监测及损伤程度评价.方法 采用自感式压电智能骨料主动健康监测技术,通过埋置在混凝土梁内的一对传感器/驱动器接收发射扫频检测信号,将其作为检测样本并结合小波分析技术及其统计特征,提取最优损伤信号,结合压电波动原理,建立小波分解的混凝土结构损伤统计模式识别算法.结果 混凝土梁损伤后,以扫频波作为主动健康监测信号的幅值产生了较大的衰减,试件在完全破坏后的统计损伤指数均值分别为35.9%和66.2%,利用小波分解的损伤统计模式识别算法能有效识别结构所处的健康状态.结论 基于压电波动理论的主动监测技术能有效识别混凝土梁不同区域的损伤状态,为压电混凝土结构动态、长期监测裂缝开展状态与损伤统计识别技术及其系统的研发提供新的思路.%This paper proposes a statistical pattern identification algorithm of wavelet decomposition, which is established by wavelet analysis and statistical characteristics analysis and then extracting optimal damage signals. The statistical distribution of signal amplitude and the relative damage index are obtained for the use of active health monitoring and PZT wave theory. Due to advantages of convenient in production, high sensitivity, reasonable performance-price ratio, self-sensing piezoelectric ceramic (PZT) smart aggregates as sensor and actuator are embedded in reinforced concrete beams with three-point bending to generate sin-sweep excitation signals on-line and detect real-time signals with digital oscilloscope before and after damage based on PZT active health monitoring. Tests show that the amplitude of active monitoring signal produced a larger attenuation and the statistical average of

  19. 热释电探测器PZT晶片制备工艺研究%Study on Fabrication of Pyroelectric Detector PZT Wafer

    Institute of Scientific and Technical Information of China (English)

    黄江平; 王羽; 袁俊; 王学森; 郭雨航; 余瑞云

    2013-01-01

      This paper introduces the study of pyroelectric detector PZT wafer and the theory basis of choice of lead zirconate titanate(PZT)as sensitive element material. It also describes polishing and grinding theory. Factors affecting the polishing quality are analyzed in detail. The crystal surfaces polished by several different polishing liquid are analyzed by SEM, and SEM photos, surface roughness analysis and crystal surface morphology were gained. The best polishing material was determined. Through the combination of theory and practice, the pyroelectric detector wafer which could meet the technological requirements was got.%  介绍了热释电探测器PZT晶片制备工艺及选择锆钛酸铅(PZT)陶瓷材料制作敏感元的理论依据,阐述了晶片磨抛理论,对磨抛质量影响因素进行了细致分析。对比了几种抛光液对晶片表面的抛光效果,并进行了扫描电镜和表面粗糙度分析,得到了抛光后晶片表面的扫描电子显微镜(SEM)照片和晶片表面形态,确定了最佳抛光材料。通过理论和实践的结合,研制出了完全能满足器件工艺要求的热释电探测器晶片。

  20. 超音速等离子喷涂PZT涂层的结构与性能研究%Structure and performance study of PZT coating prepared by supersonic plasma spraying

    Institute of Scientific and Technical Information of China (English)

    李国禄; 顾林松; 王海斗; 邢志国

    2014-01-01

    Lead-zirconate-titanate (PZT)was important functional materials which were widely used due to their perfect piezoelectric properties.In this paper,coatings were prepared by supersonic plasma spraying,the micro-structure morphology and phase composition of PZT powder and coating were analyzed by SEM,XRD and TEM,as well as making the experiment of the bonding strength,micro hardness and dielectric property on the coating.The results indicated that the coating have a denser structure and low porosity,the surface of the PZT coating was smooth,characteristics of porosity was 1.6%,the average micro hardness reached 562.3 Hv.The dielectric constant of the coating made by the supersonic plasma spraying was about 370 ℃.%锆钛酸铅(PZT)是一种应用广泛具有优良压电性能的功能材料,采用超音速等离子喷涂的方法在45#钢基体表面制备了PZT陶瓷涂层,采用 X射线衍射(XRD)对烧结粉末和 PZT 涂层相组成进行了检测,利用场发射扫描电子显微镜(SEM)对粉末和喷涂层形貌进行了观察,利用 TEM透射电子显微镜对涂层的微观结构进行了分析,并对涂层的显微硬度以及介电性能进行了测试.结果表明,超音速等离子喷涂制备的 PZT 涂层表面平整,结构致密,孔隙率为1.6%,平均显微硬度为562.3 Hv,居里温度为370℃.

  1. Synthesis and mechanical characterization of PZT/Sr based composite ceramics with addition of Si{sub 3}N{sub 4}; Sintese e caracterizacao mecanica de ceramicas compositas a base de PZT/Sr com adicoes de Si{sub 3}N{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Santos, M.A.P.; Santos, R.C.P.; Santos, M.C.C.; Rocha, C.D.G.; Silva, M., E-mail: cida@ipqm.mar.mil.b [Instituto de Pesquisas da Marinha (IPqM), Ilha do Governador, RJ (Brazil). Grupo de Materiais

    2010-07-01

    In the Underwater Acoustics field, piezoelectric ceramics are the most usually employed materials for the conversion of mechanical energy (acoustic signal) into electric energy (electric signal) and vice-versa, in sensors (hydrophones) or hydroacoustic projectors. In the development of new compositions for these applications, piezoelectric performance is generally prioritized, to the expense of its mechanical properties. With this in mind, the object of this work was to study the effects of the addition of Si{sub 3}N{sub 4} in the mechanical properties of PZT-Sr based electronic ceramics. Thus, a novel piezoelectric ceramic with the addition of small percentages in weight (0;0.1;1;3 and 5) of the structural ceramic Si{sub 3}N{sub 4} was successfully processed by the oxide mixing route ; the compounds were sintered in a conventional at 1200 deg C for 2h. The densities of the compounds thus obtained for the different percentages of Si{sub 3}N{sub 4} ranged from 55 to 97% and decreased with the increase of the content of Si{sub 3}N{sub 4}. Presence of equiaxial grains with normal growth was observed in all samples. MEV/EDS analysis of the micro-structures of the compositions detected the presence of a second phase rich in Zr, confirmed by DRX, which is a result of large quantities of volatilized PbO; the sintered pieces had their mechanical properties investigated by ultra-sonic inspection. It was observed that, among the sintered compositions, the PZT-Sr ceramic with 0.1% Si{sub 3}N{sub 4} presented the smallest value for Young's Modulus E and Shear Modulus G, 75 Gpa and 28 Gpa, respectively. The Poisson's Coefficients {nu} tended to decrease with the increase of Si{sub 3}N{sub 4} added to the PZT-Sr ceramic, indicating, thus, that the added compound may be used to adjust the mechanical properties of the material. (author)

  2. Direct Write Assembly of Three-dimensional PZT Woodpile Structure%三维PZT木堆结构的直写成型

    Institute of Scientific and Technical Information of China (English)

    蔡坤鹏; 孙竞博; 李勃; 周济

    2011-01-01

    配制了一种水基锆钛酸铅(PZT)陶瓷浆料,通过直写无模成型的方法制备了直径为微米级的压电木堆结构.流变学测量表明,浆料属于剪切变稀型流体;微观形貌观察和密度测量表明,烧结后的样品已经成瓷,且具有较高的致密度;X射线衍射(XRD)的测试结果表明,烧结后的样品具有三方PbZr0.58Ti0.42O3相;压电常数测试结果显示该结构有较好压电性,且压电常数d33为410pC/N.无模成型技术具有结构可设计性强,成型速度快,成型精度高等优点,为压电材料和器件的设计和应用提供了新的思路.%A novel kind of water based lead zirconate titanate (PZT) ink was developed. Woodpile structures with diameter of micrometer scale were constructed from this ink by using direct write assembly technique. According to the rheological test, the ink shows shear-thinning behavior. Micro-morphology and density test results show that the sintered samples have formed ceramics with high relative density. Measurement of X-ray diffraction (XRD) shows that the main phase of sintered samples is rhombohedral PbZr0.58Ti0.42O3. The value of piezoelectric constant d33 is measured to be 410 pC/N, which shows that the sintered samples exhibit good piezoelectric property. The direct write assembly technique has merits of good designability, rapid forming capability and high precision prototyping, which provide new ideas and methods for the design and application of piezoelectric materials and devices.

  3. Measurement of the Length of Installed Rock Bolt Based on Stress Wave Reflection by Using a Giant Magnetostrictive (GMS) Actuator and a PZT Sensor

    Science.gov (United States)

    Luo, Mingzhang; Li, Weijie; Wang, Bo; Fu, Qingqing; Song, Gangbing

    2017-01-01

    Rock bolts, as a type of reinforcing element, are widely adopted in underground excavations and civil engineering structures. Given the importance of rock bolts, the research outlined in this paper attempts to develop a portable non-destructive evaluation method for assessing the length of installed rock bolts for inspection purposes. Traditionally, piezoelectric elements or hammer impacts were used to perform non-destructive evaluation of rock bolts. However, such methods suffered from many major issues, such as the weak energy generated and the requirement for permanent installation for piezoelectric elements, and the inconsistency of wave generation for hammer impact. In this paper, we proposed a portable device for the non-destructive evaluation of rock bolt conditions based on a giant magnetostrictive (GMS) actuator. The GMS actuator generates enough energy to ensure multiple reflections of the stress waves along the rock bolt and a lead zirconate titantate (PZT) sensor is used to detect the reflected waves. A new integrated procedure that involves correlation analysis, wavelet denoising, and Hilbert transform was proposed to process the multiple reflection signals to determine the length of an installed rock bolt. The experimental results from a lab test and field tests showed that, by analyzing the instant phase of the periodic reflections of the stress wave generated by the GMS transducer, the length of an embedded rock bolt can be accurately determined. PMID:28241503

  4. 热释电红外探测器PZT晶片粘接质量控制%Quality Control of the PZT Wafer Bonding in Pyroelectric Infrared Detector

    Institute of Scientific and Technical Information of China (English)

    黄江平; 冯江敏; 王羽; 苏玉辉; 信思树; 李玉英

    2013-01-01

    热释电红外探测器芯片研制中,晶片粘接是芯片研制中的关键工艺之一。本文详细论述了粘接胶的选择依据及晶片粘接质量控制。确定了适合器件研制的粘接胶和粘胶工艺流程。对粘接中出现的问题及解决办法进行了讨论。研制出了完全能满足器件工艺要求的热释电探测器PZT晶片。%The wafer bonding is one of the key technologies in pyroelectric infrared detector chip development. This paper discusses the selection basis of bonding glue and quality control of wafer bonding in details, also determines the adhesive glue and the technology suitable for detector development, and analyzes the problems and the resolution method in the course of wafer bonding. The PZT wafer that can fully meet the technology requirements of pyroelectric detector is provided.

  5. Measurement of the Length of Installed Rock Bolt Based on Stress Wave Reflection by Using a Giant Magnetostrictive (GMS) Actuator and a PZT Sensor.

    Science.gov (United States)

    Luo, Mingzhang; Li, Weijie; Wang, Bo; Fu, Qingqing; Song, Gangbing

    2017-02-23

    Rock bolts, as a type of reinforcing element, are widely adopted in underground excavations and civil engineering structures. Given the importance of rock bolts, the research outlined in this paper attempts to develop a portable non-destructive evaluation method for assessing the length of installed rock bolts for inspection purposes. Traditionally, piezoelectric elements or hammer impacts were used to perform non-destructive evaluation of rock bolts. However, such methods suffered from many major issues, such as the weak energy generated and the requirement for permanent installation for piezoelectric elements, and the inconsistency of wave generation for hammer impact. In this paper, we proposed a portable device for the non-destructive evaluation of rock bolt conditions based on a giant magnetostrictive (GMS) actuator. The GMS actuator generates enough energy to ensure multiple reflections of the stress waves along the rock bolt and a lead zirconate titantate (PZT) sensor is used to detect the reflected waves. A new integrated procedure that involves correlation analysis, wavelet denoising, and Hilbert transform was proposed to process the multiple reflection signals to determine the length of an installed rock bolt. The experimental results from a lab test and field tests showed that, by analyzing the instant phase of the periodic reflections of the stress wave generated by the GMS transducer, the length of an embedded rock bolt can be accurately determined.

  6. Dielectric and magnetic properties of 0.4PZT+0.6NiCuZn-ferrite composites modified with P2O5-Co2O3

    Science.gov (United States)

    Jia, Lijun; Zhang, Huaiwu; Li, Tao; Liu, Yingli; Wen, Qiye; Shen, Jian

    2010-05-01

    P2O5 and Co2O3 have been introduced to 0.4PZT+0.6NiCuZn-ferrite composites in order to improve their electromagnetic properties, particularly for the suppression of electromagnetic interference. The nonlinear fitting of the results of permeability dispersion has revealed the relationships between domain wall resonance, spin rotation relaxation mechanisms, microstructure, and local induced anisotropy. The P2O5 additive can enhance the bulk density and static permeability due to its instantaneous liquid phase at low temperature. The existence of local induced anisotropy caused by ordering of Co ions results in a decrease in static permeability and an increase in the Q-factor. Meanwhile, the addition of Co2O3 can improve the dielectric constant and the loss tangent (tan δe) by increasing the oxygen vacancy concentration. The further decrease in tan δe of the samples codoped with P2O5 and Co2O3 is mainly attributed to P5+ in the grain boundary which can increase cation vacancies in the grain boundary region.

  7. An In Situ Electric Field Study of Magnetoelectric Coupling in PZT-LSMO Thin Film Heterostructures Using Polarized Neutron Reflectometry and Transmission Electron Microscopy

    Science.gov (United States)

    Spurgeon, Steven; Sloppy, Jennifer; Huang, Esther; Vasudevan, Rama; Lofland, Samuel; Lauter, Valeria; Valanoor, Nagarajan; Taheri, Mitra

    2013-03-01

    The development of ``spintronics'' devices based on charge and spin transport has signaled a paradigm shift in the design of data storage and computing technologies. Magnetoelectric materials, which exhibit intrinsic coupling between electronic and magnetic order, are ideal for these applications. Unfortunately, single-phase magnetoelectrics are exceedingly rare in nature and attention has turned to composite heterostructures that display coupled functionalities at interfaces. A promising system in which to explore this coupling is a thin film oxide heterostructure of the piezoelectric Pb(Zr0.2Ti0.8)O3 (PZT) and the half-metal La0.7Sr0.3MnO3 (LSMO). We show that it is possible to construct a capacitor-type device structure from these materials that may form the basis for an electrically-switched magnetic memory. We conduct polarized neutron reflectometry (PNR) measurements and measure changes in the magnetization depth profile throughout the composite under the reversal of an in situ electric field. We then correlate these PNR results to local strain and chemistry using transmission electron microscopy (TEM). We find that a combination of charge doping and strain mechanisms governs coupling in this system.

  8. Influence of La in xPBBiN of ternary nanoceramic composite (1-x0.5PMN-0.5PZT-xPBBiN system by mechanic al activatio n technique for dielectric and piezoelectric properties

    Directory of Open Access Journals (Sweden)

    K. CHANDRAMOULI

    2011-06-01

    Full Text Available (1-x[0.5Pb(Mg0.33Nb0.67O3-0.5Pb(Zr0.53Ti0.47O3]-x[Pb0.557Ba0.38La0.022Bi0.02Nb2O6] with both perovskite and tungsten bronze structured composite have been synthesized through mechanical activation technique. The strong influence of lanthanum addition to the lead-barium-bismuth-niobate (xPBLBiN ceramics in perovskite structured (1-xPMN-PZT on structural and functional properties is confirmed. X-ray diffraction patterns studies showed that these complex composites consisted of perovskite Cubic with tungsten bronze Orthorhombic phases. La modification in PBBiN of a ternary system (1-xPMN-PZTxPBBiN revealed intensified orthorhombicity. As La increased the dielectric and piezoelectric properties tremendously increased in (1-xPMN-PZT-xPBLBiN nanoceramic composite. The optimum dielectric and piezoelectric properties (εRT = 2931, kp = 0.461 and d33 = 428 pC/N were found in x =0.4 composite. We achieved novel nanocomposites synthesized by high energy ball milling method and having binary structures in a single composite with excellent functional properties that can be used for energy harvesting applications.

  9. Equivalent Circuit Model of Low-Frequency Magnetoelectric Effect in Disk-Type Terfenol-D/PZT Laminate Composites Considering a New Interface Coupling Factor

    Directory of Open Access Journals (Sweden)

    Guofeng Lou

    2017-06-01

    Full Text Available This paper describes the modeling of magnetoelectric (ME effects for disk-type Terfenol-D (Tb0.3Dy0.7Fe1.92/PZT (Pb(Zr,TiO3 laminate composite at low frequency by combining the advantages of the static elastic model and the equivalent circuit model, aiming at providing a guidance for the design and fabrication of the sensors based on magnetoelectric laminate composite. Considering that the strains of the magnetostrictive and piezoelectric layers are not equal in actual operating due to the epoxy resin adhesive bonding condition, the magnetostrictive and piezoelectric layers were first modeled through the equation of motion separately, and then coupled together with a new interface coupling factor kc, which physically reflects the strain transfer between the phases. Furthermore, a theoretical expression containing kc for the transverse ME voltage coefficient αv and the optimum thickness ratio noptim to which the maximum ME voltage coefficient corresponds were derived from the modified equivalent circuit of ME laminate, where the interface coupling factor acted as an ideal transformer. To explore the influence of mechanical load on the interface coupling factor kc, two sets of weights, i.e., 100 g and 500 g, were placed on the top of the ME laminates with the same thickness ratio n in the sample fabrication. A total of 22 T-T mode disk-type ME laminate samples with different configurations were fabricated. The interface coupling factors determined from the measured αv and the DC bias magnetic field Hbias were 0.11 for 500 g pre-mechanical load and 0.08 for 100 g pre-mechanical load. Furthermore, the measured optimum thickness ratios were 0.61 for kc = 0.11 and 0.56 for kc = 0.08. Both the theoretical ME voltage coefficient αv and optimum thickness ratio noptim containing kc agreed well with the measured data, verifying the reasonability and correctness for the introduction of kc in the modified equivalent circuit model.

  10. Equivalent Circuit Model of Low-Frequency Magnetoelectric Effect in Disk-Type Terfenol-D/PZT Laminate Composites Considering a New Interface Coupling Factor.

    Science.gov (United States)

    Lou, Guofeng; Yu, Xinjie; Lu, Shihua

    2017-06-15

    This paper describes the modeling of magnetoelectric (ME) effects for disk-type Terfenol-D (Tb0.3Dy0.7Fe1.92)/PZT (Pb(Zr,Ti)O₃) laminate composite at low frequency by combining the advantages of the static elastic model and the equivalent circuit model, aiming at providing a guidance for the design and fabrication of the sensors based on magnetoelectric laminate composite. Considering that the strains of the magnetostrictive and piezoelectric layers are not equal in actual operating due to the epoxy resin adhesive bonding condition, the magnetostrictive and piezoelectric layers were first modeled through the equation of motion separately, and then coupled together with a new interface coupling factor kc, which physically reflects the strain transfer between the phases. Furthermore, a theoretical expression containing kc for the transverse ME voltage coefficient αv and the optimum thickness ratio noptim to which the maximum ME voltage coefficient corresponds were derived from the modified equivalent circuit of ME laminate, where the interface coupling factor acted as an ideal transformer. To explore the influence of mechanical load on the interface coupling factor kc, two sets of weights, i.e., 100 g and 500 g, were placed on the top of the ME laminates with the same thickness ratio n in the sample fabrication. A total of 22 T-T mode disk-type ME laminate samples with different configurations were fabricated. The interface coupling factors determined from the measured αv and the DC bias magnetic field Hbias were 0.11 for 500 g pre-mechanical load and 0.08 for 100 g pre-mechanical load. Furthermore, the measured optimum thickness ratios were 0.61 for kc = 0.11 and 0.56 for kc = 0.08. Both the theoretical ME voltage coefficient αv and optimum thickness ratio noptim containing kc agreed well with the measured data, verifying the reasonability and correctness for the introduction of kc in the modified equivalent circuit model.

  11. Biotemplated Synthesis of PZT Nanowires

    Science.gov (United States)

    2013-11-25

    periodically using a vibration generator connected to a mechanical indenter. Measurements were conducted at various resistive loads and frequencies...Figure 4d). Finally, a one-dimensional model for the system was developed to corroborate the experimental results (details in the Supporting Information...Haider, H. IEEE/ASME Trans. Mechatron 2005, 10, 240−252. (10) Wang, X. Nano Energy 2012, 1, 13−24. (11) Kumar, B.; Kim, S.-W. J. Mater. Chem. 2011, 21

  12. Modeling and control for PZT micro-displacement Actuator%压电陶瓷微位移驱动器建模与控制

    Institute of Scientific and Technical Information of China (English)

    刘泊; 郭建英; 孙永全

    2013-01-01

    When a white light interferometer is applied to 3D surface microcosmic topographic measurement,the measuring accuracy is effected by the hysteresis and creeping phenomenon generated by the piezoelectric actuator seriously.Therefore,this paper proposes a method to improve the displacement accuracy of the reference mirror along the optical axis direction.The piezoelectric actuator is given,and its displacement detecting circuit,PID closed loop control algorithms,and creep compensation control are studied.First,displacement detecting circuit is established by a position sensitive device and an optical lever,by which the piezoelectric ceramic micro-displacement can be fed back to control the system,then the PID closed-loop control algorithm is established.Furthermore,the creeping characteristics of piezoelectric ceramic is discussed during the measurement.In order to eliminate the creeping phenomenon and improve measurement accuracy,the “voltage creep” compensation model is proposed.Finally,an integer control system based on PID closed-loop control and creep compensation control is established.The micro-displacement of the piezoelectric actuator is measured by a high-precision XL-80 laser interferometer under the two cases of PID closed-loop control and integer control.Experimental results indicate that the displacement error for the former is 0.007 μm,and that for the latter is 0.005 μm,respectively.This method reduces the influence of hysteresis and creeping on measurement results,and meets the requirements of three-dimensioned shape measurement for high accuracy.%考虑利用白光干涉仪进行表面三维形貌测量时压电陶瓷(PZT)的蠕变效应对微位移驱动器位移精度的影响,提出了一种沿参考镜光轴方向提高该驱动器位移精度的方法.系统研究了该驱动器的位移检测回路、PID闭环控制以及蠕变补偿控制;利用光电位置传感器和光学杠杆调节位移检测回路,将压电陶瓷驱动器微位

  13. Modeling and analysis of a circular PZT energy-generator used in hydraulic liquid absorber%液压流体吸振器用圆形压电发电装置的建模与性能分析

    Institute of Scientific and Technical Information of China (English)

    王淑云; 阚君武; 王鸿云; 李征; 赵子超; 万杰; 曹迪

    2012-01-01

    A piezoelectric energy harvester used in hydraulic liquid absorber was presented. To enhance the energy-generating capability and obtain the optimal structural/material parameters, the analysis model of clamped PZT disk generator under concentrated force was established utilizing the theory of plates and shells. The influences of radius ratio (λ) , thickness ratio (β) as well as material Young's modulus ratio ( ζ) of the PZT disk on energy generation were investigated. The results show that there is an optimal pair of X and β for a PZT disk generator with given ζ to obtain maximal electrical energy. Similarly, in the case of given X and β, there is an optimal ζ, which decreases with the decrease of β and is not influenced by the change of X under given β. At the same time, reducing ζ is helpful for the generator to generate more electrical energy. When aluminum or beryllium bronze plates are used as substrates, the optimal radius ratio and thickness ratio are (0.45, 0.45) or (0.585, 0.6), respectively. The maximal electric energy generated are 1.14643 x 10 -4J and 1.01893 x 10-4J, respectively.%提出一种用于液压流体吸振器的压电发电装置.为提高所用圆形压电振子的发电能力,获得最优的结构及材料性能参数,利用板壳理论建立了固支边界条件下的位移曲线及发电量的理论分析模型,研究了半径比(陶瓷/基板)、厚度比(陶瓷/总厚度)及弹性模量比(基板/陶瓷)等对其发电能力的影响规律.研究表明,在压电振子材料确定时,存在最佳的半径比和厚度比使其发电能力最大;在压电振子结构尺寸确定时,存在最佳的弹性模量比使发电量最大,且厚度比确定时的最佳弹性模量比与半径比无关、半径比确定时的最佳弹性模量比随厚度比的减小而降低;减小弹性模量比有助于提高压电振子的发电能力.铝基板及铍青铜基板压电振子的最佳半径比/厚度比分别为0.45/0.45和0

  14. 制备工艺对Fe掺杂PZN-PZT热释电陶瓷性能的影响%The effects of synthesis route on the electricalproperties of Fe-doped PZN-PZT pyroelectric ceramics

    Institute of Scientific and Technical Information of China (English)

    韦慧; 陈拥军; 郭栋

    2016-01-01

    采用传统氧化物反应法(一步法)和前驱体法(两步法)合成铁掺杂改性的0.075Pb(Zn1/3 Nb2/3)O3-0.925Pb(Zr0.95 Ti0.05)O3(PZN-PZT)热释电陶瓷,研究制备方法对PZN-PZT热释电陶瓷的微观形貌、相结构及电学性能的影响。XRD结果表明,采用一步法制备的陶瓷不如两步法,前者存在钙钛矿相和少量焦绿石相,后者能有效抑制焦绿石相的生成,陶瓷为纯菱方钙钛矿相。SEM分析进一步证实了两步法能够制备出晶粒分布均匀、晶型饱满的致密陶瓷。结合介电、铁电及热释电性能分析可知,单一钙钛矿结构和均匀紧凑的晶粒结构对陶瓷材料电学性能的增强起着重要的作用。%Fe-doped 0.075 Pb(Zn1/3 Nb2/3 )O3-0.925Pb(Zr0.95 Ti0.05 )O3 (PZN-PZT)pyroelectric ceramics were pre-pared by a conventional oxide-mixed one-step method and precursor two-step method,respectively.The phase structure and electrical properties of the prepared ceramics were systematically investigated.X-ray diffraction results indicated that the ceramics fabricated by the one-step method possess a mixture of perovskite phase and pyrochlore phase,while the ceramics prepared from the two-step method have a single perovskite phase struc-ture.Scanning electron microscopy observation suggests that the ceramics prepared by the two-step method have a dense microstructure with uniform grains.The dielectric,ferroelectric and pyroelectric properties were measured,which revealed that the ceramics with single phase and dense microstructure have enhanced ferroelec-tric and pyroelectric properties.

  15. Study on Inter-Diffusion Barrier Layer between PZT Pyroelectric Thick Film and Si Substrate%PZT厚膜与Si衬底互扩散阻挡层研究

    Institute of Scientific and Technical Information of China (English)

    陈冲; 吴传贵; 彭强祥; 罗文博; 张万里; 王书安

    2013-01-01

    在Pt/Ti/SiO2/Si基片上,利用电泳沉积制备PZT热释电厚膜材料.为防止Pb和Si互扩散,在Pt底电极与SiO2/Si衬底间通过直流磁控溅射制备了TiOx薄膜阻挡层.对具有0、300 nm和500 nm TiOx阻挡层的PZT厚膜材料用SEM和能量色散谱仪(EDS)表征了Pb和Si互扩散情况,用动态热释电系数测量仪测试了热释电系数.结果表明,当TiOx阻挡层为500 nm时,可阻挡Pb和Si互扩散,热释电性能最好.热释电系数p=1.5×10-8 C·cm-2·K-1,相对介电常数εr=170,损耗角正切tanδ=0.02,探测度优值因子Fd=1.05×10-5pa-0.5.%PZT thick film as pyroelectric material has been prepared on the Pt/Ti/SiCK/Si substrate by using the electrophoresis deposition (EPD) method. In order to prevent the inter-diffusion between Pb and Si,a TiOx film barrier layer between Pt bottom electrode and SiO2/Si substrate has been prepared by using the DC magnetron sputtering method. The inter-diffusion between Pb and Si in PZT thick film material with TiO, barrier layer thickness of 0, 300 nm and 500 nm respectively have been characterized by SEM and EDS. The pyroelectric coefficient has been measured by the dynamic pyroelectric coefficient instrument. The results show that the inter-diffusion between Pb and Si can be blocked when the thickness of TiOx barrier layer is 500 nm and have the best pyroelectric properties. The pyroelectric coefficient, relative dielectric constant,dielectric loss and detectivity figure of merit are p=1. 5 × 10-8C · cm-2k-1 ,εr = 170,tan 8=0. 02 and Fd = 1. 05 × 10-5 Pa-0.5 respectively.

  16. 电致伸缩/压电微尺度智能结构的伽辽金方法%A Galerkin method for a micro-scale smart structure with PMN-PT/PZT patches

    Institute of Scientific and Technical Information of China (English)

    高海昌; 崔舒宁; 张元冲

    2003-01-01

    在微纳米尺寸的智能结构中,电致伸缩(PMN-PT)/压电(PZT)材料有着广泛的应用前景[1,2].本文基于哈密顿变分原理,得到PMN-PT/PZT微尺度梁的智能结构系统运动方程的弱形式.采用以B样条函数为基函数的有限维近似的伽辽金方法,建立起该系统的状态方程.对于由PMN-PT的诱导应变与电场成双曲唯象关系引起的非线性问题,采用线性化输出方法[3],获得作动诱导应变与控制器输出的线性关系.以PZT做传感器、PMN-PT做作动器的梁系统的控制算例表明了方法的正确性与有效性.此方法可进一步推广到更为复杂的智能结构系统中.

  17. Fabrication and characterization of ternary compound PMnN-PZT thin films on silicon substrates%硅基三元系PMnN—PZT铁电薄膜制备与研究

    Institute of Scientific and Technical Information of China (English)

    张涛; 张淑仪; 李敏; 周胜男; 孙斌

    2012-01-01

    利用磁控溅射方法在单晶Si基底上沉积三元系铁电薄膜6%PMnN-94%5PZT(6%Pb(Mn1/3,Nb2/3)O3—94%Pb(Zr0.52,Ti0.48)O3),采用淬火方法对薄膜进行处理,以促进薄膜钙钛矿结构形成。同时,在相同条件下制备非掺杂PZT(52/48)薄膜以对比薄膜掺杂效果。运用X射线衍射(XRD)技术分析薄膜晶向及晶体结构,运用SawyerTower电路测试薄膜铁电性能,运用激光测振仪测试薄膜的压电系数。实验结果表明,所沉积薄膜为多晶钙钛矿结构铁电薄膜,薄膜铁电剩余极化Pr=23.7μC/cm2,饱和极化Ps=40μC/cm2,矫顽场电压2Ec=139kV/cm,横向压电系数e11=-13.2C/m2,薄膜的铁电及压电性能优良。%The ternary compound ferroelectric thin films, 6% Pb ( Mnl/3 , Nb2/3 ) O3-94 % Pb (Zr0.52, Ti0.48 ) 03, were deposited on the silicon substrates by the magnetron sputtering method, and the quench method was adopted for the post heat treatment for the perovskite phase. Besides, the non-doped PZT(52/48) thin films were also fab- ricated for comparisons with the same sputtering method. The X-ray diffraction was used to characterize the crystal structures of thin films, and the Sawyer Tower circuit was used to measure the ferroelectricity, and the laser vibration measurement system was used to measure the transverse piezoelectric coefficient of thin films. The results show that the PMnN-PZT thin films own perovskite structures, and the remnant polarization Pr = 23. 7μC/cm2 , the saturation polarization Ps=40μC/cm2 and the coercive electric field 2Ec=139kV/cm, and the transverse piezoelectric coefficient c31 = - 13. 2C/m2 , which identifies that the PMnN-PZT thin films own excellent ferroeleetricity and piezoelectricity.

  18. 基于单激发端多接收端压电阵列的板内损伤检测%Damage Detection for a Plate Based on a Single-transmitter Multi-receiver PZT Array

    Institute of Scientific and Technical Information of China (English)

    田振华; 徐鸿; 李鸿源; 常愿

    2014-01-01

    Based on ultrasonic guided wave technique ,the damage detection for plates was studied . The characteristics of Lamb wave propagation were discussed herein .With the help of finite element coupling field simulation ,the wave propagation and wave interaction with crack damage of Lamb waves were simulated .From the simulation results ,the affection of crack size on Lamb wave propaga‐tion was analyzed .In order to quantify the locations and sizes of the damages ,a single-transmitter multi-receiver PZT array was employed .Combined with probability-based imaging method ,the dam‐age distribution of the plate could be obtained .The imaging results of this distribution can reflect the location and severity of the damage obviously .%基于超声导波技术研究了板状结构的损伤检测。理论分析了平板中 Lamb 波的传播特点;利用有限元耦合场模拟方法模拟了平板中 Lamb 波的传播及裂纹对 Lamb 波的影响;根据有限元模拟结果,分析了裂纹尺寸对 Lamb 波传播的影响;为检测损伤的位置,建立了单激发端多接收端的压电阵列;结合概率成像算法,建立了损伤分布场,该分布场的成像结果直观地反映了损伤的位置和严重程度。

  19. Doping effects of CuO additives on the properties of low-temperature-sintered PMnN-PZT-based piezoelectric ceramics and their applications on surface acoustic wave devices.

    Science.gov (United States)

    Tsai, Cheng-Che; Chu, Sheng-Yuan; Lu, Chun-Hsien

    2009-03-01

    To develop the anisotropic ceramic substrate with low sintering temperature for surface acoustic wave (SAW) applications, the low cost and feasible material with moderate piezoelectric properties, good dielectric properties, and higher Curie temperature were explored. The piezoelectric ceramics with compositions of Pb[(Mn(1/3)Nb(2/3))(0.06-) (Zr(0.52)Ti(0.48))0.94] O(3) (PMnN-PZT) + 0.5 wt.% PbO + x wt.% CuO (0.05 = x = 0.3) had been prepared by the conventional mixed-oxides method. CuO dopants were used as the sintering aid to improve the bulk density under low sintering temperature (i.e., 980-1040 degrees C). The phase structures, microstructures, frequency behavior of dielectric properties (up to 50 MHz), piezoelectric properties, ferroelectric properties, and temperature stability with the amount of CuO additive were systematically investigated. Experimental results showed that the sintering temperature could be lowered down to 1020 degrees C and still keep reasonably good piezoelectric activity (i.e., high electromechanical coupling factor (k(p)), (k(t)) and dielectric and ferroelectric properties. The preferable composition, obtained at x = 0.1, presented the values of the electromechanical coupling factor (k(p)) (k(t)), mechanical quality factor (Q(m)), piezoelectric charge constant (d(33)), dielectric constant, dielectric loss, temperature coefficient of resonant frequency (TCF(B)), and Curie point (T(c)) of 0.54, 0.48, 850, 238 pc/N, 1450, 0.0023, 1.1 kV/mm, 26 coul/cm(2), -150 ppm/ degrees C, and 348 degrees C. Using this developed low-temperature-sintered material to make the piezoelectric substrate, the SAW filter was fabricated and its properties were measured. Results showed that this device possessed very high value of k(2)(7.13%) with a good TCF (-40.15 ppm/ degrees C), and a surface wave velocity (V(P)) of 2196 m/s.

  20. Flexoelectricity in PZT Nanoribbons and Biomembranes

    Science.gov (United States)

    2015-01-09

    equations were used to solve for the stress, displacement and polarization fields in several one and two-dimensional electromechanical problems...Princeton on several projects. We studied the electromechanical response of neuronal cells, energy harvesting using pyro-para-electricity and a new way of...08/20/2014 Received Paper 6.00 2.00 3.00 5.00 Prashant Purohit, Sheng Mao. Defects in flexoelectric solids, Journal of the Mechanics and Physics of

  1. Zr含量对大功率0.125PMN-0.875PZT陶瓷压电性能的影响%Effects of Zr content on piezoelectric properties of 0.125PMN-0.875PZT high power ceramics

    Institute of Scientific and Technical Information of China (English)

    葛宏桂; 刘云飞; 吕忆农; 周怀娟

    2012-01-01

    The 0. 125Pb(Mg1/2 Nb2/3)O_3 -0. 875PbZrxTi1-xO3(0. 125PMN -0. 875PZT) ternary piezoelectric ceramics with different Zr contents ( x = 0. 46 ~ 0. 52 ) were prepared by the two-step solid-state reaction. The sintering,structural and electrical properties of 0. 125PMN-0. 875PZT ceramics with zirconium content were investigated by X-ray diffractmeter ( XRD) and impedance analysis meter. The results indicated that 0. 125PMN-0. 875 PZT ceramics had a single perovskite structure by the two-step synthesis method, and there was a tetragonal-rhombohedral morphotropic phase boundary ( MPB ) with x = 0. 48 ~ 0. 50, and the excellent properties were optimal at x = 0. 49: the bulk density was 7. 84 g/cm3, dielectric loss (tanδ) was 0.76% ,relative dielectric constant (εr) was 2 130, piezoelectric constant (d33) was 320 pC/N, electromechanical coupling coefficient ( Kp ) was 0. 61, and mechanical quality factor ( Qm) was 76.%采用二次合成法制备不同Zr含量(x=0.46~0.52)的0.125Pb(Mg1/3 Nb2/3)O3 -0.875PbZLTi1-xO3(0.125PMN -0.875PZT)三元压电陶瓷.采用X线衍射仪(XRD)、阻抗分析仪等对陶瓷进行表征和性能测试,考察了Zr含量变化对陶瓷烧结相结构、体积密度、介电和压电性能的影响.结果表明:采用二次合成法,制备了纯钙钛矿相结构的陶瓷;当x=0.48~0.50时,0.125PMN -0.875PZT陶瓷处于四方-三方准同型相界(MPB),在x=0.49时制备的0.125PMN -0.875PZT陶瓷性能最佳,体积密度为7.84 g/cm3,介电损耗低至0.76%,相对介电常数为2 130,压电常数为320 pC/N,机电耦合系数达0.61,机械品质因数为76.

  2. Metallo-Organic Solution Deposition of Ferroelectric PZT Films

    Science.gov (United States)

    1992-09-09

    perovskite structure was reduced by the presence of a cubic pyrochiore-like phase related to Pb 2Ti20 6 [24]. The films consolidated at 300 and 400"C are...coherent imaging, solar cell physics, battery electrochemistry, battery testing and evaluation. Mechanics and Materials Technology Center: Evaluation...films. For example, lead al- koxide and dtanium alkoxide compounds can be hydrolyzed to form hydroxide-alkoidde com- pounds: Pb (OR)2 + H20--* Pb (OR

  3. 50 Hz electron emission from PZT ferro-electric cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Flechtner, D.; Golkowski, C.; Ivers, J.D.; Kerslick, G.S.; Nation, J.A.; Schachter, L. [Cornell Univ., Ithaca, NY (United States)

    1997-12-31

    Ferro-electric cathodes may offer a source of high current density electron beams for applications where the use of conventional field emitters is limited by repetition rate and lifetime. In a ferro-electric cathode, electrons are emitted when the spontaneous polarization is rapidly changed by a pulsed electric field applied across the ferroelectric. When no additional voltage is applied to a planar diode gap, emission current densities are on the order of 1 A/cm{sup 2}. When an additional field is applied to the gap, the authors have measured current densities up to 100 A/cm{sup 2}. In a new configuration that permits beam extraction into a drift tube, the cathode is pulsed 10--20kV negative and electron current densities of {approximately}20 A/cm{sup 2} at repetition rates up to {approximately}50 Hz (power supply limited) have been measured. The one inch diameter ferro-electric cathode is located in the fringing region of a 1.5 kG solenoid magnetic field {approximately}2.8 cm from the entrance of a grounded drift tube. A Faraday cup is located several centimeters inside the drift tube and measurements show that repeatable beam current can be extracted from the ferroelectric cathode in this geometry.

  4. Recent Progress on PZT Based Piezoelectric Energy Harvesting Technologies

    OpenAIRE

    Min-Gyu Kang; Woo-Suk Jung; Chong-Yun Kang; Seok-Jin Yoon

    2016-01-01

    Energy harvesting is the most effective way to respond to the energy shortage and to produce sustainable power sources from the surrounding environment. The energy harvesting technology enables scavenging electrical energy from wasted energy sources, which always exist everywhere, such as in heat, fluids, vibrations, etc. In particular, piezoelectric energy harvesting, which uses a direct energy conversion from vibrations and mechanical deformation to the electrical energy, is a promising tec...

  5. Co/Co3O4/PZT多铁复合薄膜的交换偏置效应及其磁电耦合特性∗%Exchange bias effect and magneto electric coupling behaviors in multiferroic Co/Co3O4/PZT composite thin films

    Institute of Scientific and Technical Information of China (English)

    李永超; 周航; 潘丹峰; 张浩; 万建国

    2015-01-01

    The multiferroic Co/Co3O4/PZT composite films are prepared on Pt/Ti/SiO2/Si wafers by sol-gel process combined with pulsed laser deposition method. The phase structures, microstructural topographies and element valence states of the composite films are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectrum (XPS). The ferroelectric, electrical and magnetic properties as well as the magnetoelectric coupling behaviors are measured, and the exchange bias effect and its influence on the magnetoelectric coupling behavior of the composite film are studied systematically. The results show the composite films have well-defined ferroelectric hysteresis loops with a remanent polarization value of ∼17 µC/cm2. The composite film exhibits evidently an exchange bias effect. Typically, a exchange bias field of ∼80 Oe is observed at 77 K. Both the exchange bias field and magnetic coercive field increase with reducing the temperature. The exchange bias field increases to 160 Oe when the temperature decreases to 10 K. The XPS results confirm that an about 5 nm-thick CoO layer appears at the Co/Co3O4 interface due to the oxygen diffusion during the preparation, indicating that the exchange bias effect at 77 K is caused by the pinning effect of the antiferromagnetic CoO layer while the exchange bias effect at 10 K originates from the combining effect of antiferromagnetic CoO and Co3O4 layers. The measurement results of magnetocapacitance versus magnetic field curves at different temperatures show that the composite films have remarkable magnetoelectric coupling properties. The response of capacitance to temperature changes with the variation of external magnetic field. Further investigations show that the composite film possesses distinct anisotropic magnetocapacitance effect. When the direction of the magnetic field changes, the magnetocapacitance of the composite film changes from positive value to negative value. Moreover

  6. Application of PZT thin film technology for angular resolved flame detection; Anwendung von pyroelektrischen PZT-Duennschichten fuer die winkelaufloesende Flammendetektion

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, Norbert; Ebermann, Martin; Hoppe, Silke [InfraTec GmbH, Dresden (Germany)

    2012-07-01

    Hot gases emit a specific spectral pattern in the infrared range at about 4.3 {mu}m, which can be sensed with an infrared (IR) flame detector. State-of-the-art detectors are designed as single-point detectors to detect a flame inside a certain field of view where the position of the flame cannot be resolved. The novel 3 x 3 array sensor delivers additional spatial information about the observed scene for an angular location of the flame with a resolution of about 5 . (orig.)

  7. Sinterização de cerâmicas à base de PZT em forno de microondas Microwave synthesis of PZT based ceramics

    Directory of Open Access Journals (Sweden)

    M. V. Gelfuso

    2007-09-01

    Full Text Available Cerâmicas de titanato e zirconato de chumbo dopadas com neodímio foram sinterizadas em um forno de microondas de uso doméstico modificado. Neste tipo de aquecimento, a energia eletromagnética é transferida diretamente para o material, sendo convertida em calor pelo material cerâmico, reduzindo o tempo e energia durante o processamento. Desta forma, foram produzidos corpos cerâmicos com tempo de sinterização que variou até 30 min, a 1100 e 1200 ºC. As fases foram investigadas por meio de difratometria de raios X. Corpos cerâmicos com densidade de 95% da teórica foram obtidos com tempo de sinterização de 10 min em 1100 ºC, com uma taxa de aquecimento de 400 ºC/min. Para as cerâmicas com densidade superior a 90% da teórica foram medidos os valores de constante dielétrica e fator de perda.Ferroelectric ceramics based on lead zirconate titanate doped with neodymium were sintered using a modified microwave oven. In this process the energy is transferred directly to the material through the interaction between molecules of the material with the electromagnetic field. The microwave sintering process has an advantage to reduce the time and save energy. This type of process involves energy conversion, opposing to heat transfer. Ceramic parts were produced by thermal treatments at 1100 ºC and 1200 ºC up to 30 min. The formed crystalline phases were investigated by X-ray diffraction. Ceramic parts with densities above 95% of the theoretical density were produced in 10 min by heating at 1100 ºC, with heating rate of 400 ºC/min. Values of dielectric constant and loss factor of ceramics with density above 90%T.D. were determined.

  8. Impedance Based Characterization of a High-Coupled Screen Printed PZT Thick Film Unimorph Energy Harvester

    DEFF Research Database (Denmark)

    Lei, Anders; Xu, R.; Borregaard, L. M.

    2014-01-01

    . This approach leads to simple closed form expressions for peak power frequency, optimal load, and output power without a tedious mathematical derivative approach. The closed form expressions are validated against the exact numerical solution. The electromechanical model contains a set of only five lumped......The single degree of freedom mass-spring-damper system is the most common approach for deriving a full electromechanical model for the piezoelectric vibration energy harvester. In this paper, we revisit this standard electromechanical model by focusing on the impedance of the piezoelectric device...... parameters which, by means of the piezoelectric impedance expression, all can be determined accurately by electrical measurements. It is shown how four of five lumped parameters can be determined from a single impedance measurement scan, considerably reducing the characterization effort. The remaining...

  9. Effect of Sintering Temperature on Structural and PiezoelectricProperties of PNN-PZT Ceramics

    Directory of Open Access Journals (Sweden)

    Sandeep Mahajan

    2007-01-01

    Full Text Available Sintering temperatures affect the structural and piezoelectric properties of PbNi1/3Nb2/3-PbZrO3-PbTiO3 system considerably; therefore the effect has been studied on mechano-chemicallyprocessed powder. This process involves activating mixed oxides of PbO, NiO, Nb2O5, ZrO2 andTiO2, and in the present study, calcination steps at an intermediate temperatures were skippedwhich are usually required in conventional solid state reaction methods and chemical routes.Single-phase formation was confirmed from XRD patterns which shows rhombohedral structureat higher sintering temperature. Investigations of the microstructure indicate almost linear increasein grain size from 0.98 m to 2.56  m when the sintering temperature was varied from 1050 oC to1150 °C. A high value of planar coupling factor (kp = 67 per cent and piezoelectric charge coefficient(d 33 ~ 750 pm/V; (as determined from strain versus electric field curve at low field were obtainedfor the ceramic specimens sintered at 1100 °C. The maximum strain was observed ~ 0.21 per centat 40 kV/cm applied field for the sample sintered at 1100 °C for 4 h.

  10. Properties of quasi 1-3 piezoelectric PZT-epoxy composites obtained by dielectrophoresis

    NARCIS (Netherlands)

    Ende, D.A. van den; Bory, B.F.; Groen, W.A.; Zwaag, S. van der

    2010-01-01

    The dielectric and piezoelectric properties of piezoelectric particleepoxy polymer composites structured into 1-3 composites via dielectrophoresis during curing are reported. The dielectrophoretic alignment induces a textured microstructure in the composite, with particles forming chains in the dire

  11. Stress relaxation and estimation of activation volume in a commercial hard PZT piezoelectric ceramic

    Indian Academy of Sciences (India)

    B L Cheng; M J Reece

    2001-04-01

    The stress relaxation of ferroelectric/piezoelectric material was studied using compression testing. The deformation was produced by the switching of ferroelectric domains. The internal stresses were estimated by decremental stress relaxation during unloading. The results were interpreted in terms of reversible and irreversible switching of the domains.

  12. Direct strain energy harvesting in automobile tires using piezoelectric PZT-polymer composites

    NARCIS (Netherlands)

    Ende, D.A. van den; Wiel, H.J. van de; Groen, W.A.; Zwaag, S. van der

    2012-01-01

    Direct piezoelectric strain energy harvesting can be used to power wireless autonomous sensors in environments where low frequency, high strains are present, such as in automobile tires during operation. However, these high strains place stringent demands on the materials with respect to mechanical

  13. Study of harsh environment operation of flexible ferroelectric memory integrated with PZT and silicon fabric

    KAUST Repository

    Ghoneim, Mohamed T.

    2015-08-05

    Flexible memory can enable industrial, automobile, space, and smart grid centered harsh/extreme environment focused electronics application(s) for enhanced operation, safety, and monitoring where bent or complex shaped infrastructures are common and state-of-the-art rigid electronics cannot be deployed. Therefore, we report on the physical-mechanical-electrical characteristics of a flexible ferroelectric memory based on lead zirconium titanate as a key memory material and flexible version of bulk mono-crystalline silicon (100). The experimented devices show a bending radius down to 1.25 cm corresponding to 0.16% nominal strain (high pressure of ∼260 MPa), and full functionality up to 225 °C high temperature in ambient gas composition (21% oxygen and 55% relative humidity). The devices showed unaltered data retention and fatigue properties under harsh conditions, still the reduced memory window (20% difference between switching and non-switching currents at 225 °C) requires sensitive sense circuitry for proper functionality and is the limiting factor preventing operation at higher temperatures.

  14. PZT based tunable Interdigital Transducer for Lamb waves based NDT and SHM

    Science.gov (United States)

    Mańka, Michał; Rosiek, Mateusz; Martowicz, Adam; Stepinski, Tadeusz; Uhl, Tadeusz

    2016-10-01

    In this paper a novel concept of a tunable transducer for generation and sensing of the Lamb waves is presented. The proposed transducer is developed based on a commonly applied Interdigital Transducer (IDT). In the proposed design, further referred to as the Tunable IDT (T-IDT), the conventional comb electrodes with fixed pitch are replaced by a series of densely distributed discrete electrode strips. These electrodes can be easily interconnected in different configurations to match the required wavelength without a need of applying physical changes to the electrode layout. In order to verify the properties of the T-IDT, numerical simulations and experimental tests were performed and their results were compared to the ones obtained for the IDT. The outcomes from both the numerical and experimental analyses proved that the beampatterns generated by the T-IDT are similar to those determined for the conventional transducer. Moreover, the changes in electrode connections lead to the changes of phase-amplitude characteristics.

  15. Temperature dependency of the hysteresis behaviour of PZT actuators using Preisach model

    DEFF Research Database (Denmark)

    Mangeot, Charles; Zsurzsan, Tiberiu-Gabriel

    2016-01-01

    The Preisach model is a powerful tool for modelling the hysteresis phenomenon on multilayer piezo actuators under large signal excitation. In this paper, measurements at different temperatures are presented, showing the effect on the density of the Preisach matrix. An energy-based approach...... is presented, aiming at defining a temperature-dependent phenomenological model of hysteresis for a better understanding of the non-linear effects in piezo actuators....

  16. Vibration control in plates by uniformly distributed PZT actuators interconnected via electric networks

    CERN Document Server

    Vidoli, Stefano

    2010-01-01

    In this paper a novel device aimed at controlling the mechanical vibrations of plates by means of a set of electrically-interconnected piezoelectric actuators is described. The actuators are embedded uniformly in the plate wherein they connect every node of an electric network to ground, thus playing the two-fold role of capacitive element in the electric network and of couple suppliers. A mathematical model is introduced to describe the propagation of electro-mechanical waves in the device; its validity is restricted to the case of wave-forms with wave-length greater than the dimension of the piezoelectric actuators used. A self-resonance criterion is established which assures the possibility of electro-mechanical energy exchange. Finally the problem of vibration control in simply supported and clamped plates is addressed; the optimal net-impedance is determined. The results indicate that the proposed device can improve the performances of piezoelectric actuation

  17. IIR filtering based adaptive active vibration control methodology with online secondary path modeling using PZT actuators

    Science.gov (United States)

    Boz, Utku; Basdogan, Ipek

    2015-12-01

    Structural vibrations is a major cause for noise problems, discomfort and mechanical failures in aerospace, automotive and marine systems, which are mainly composed of plate-like structures. In order to reduce structural vibrations on these structures, active vibration control (AVC) is an effective approach. Adaptive filtering methodologies are preferred in AVC due to their ability to adjust themselves for varying dynamics of the structure during the operation. The filtered-X LMS (FXLMS) algorithm is a simple adaptive filtering algorithm widely implemented in active control applications. Proper implementation of FXLMS requires availability of a reference signal to mimic the disturbance and model of the dynamics between the control actuator and the error sensor, namely the secondary path. However, the controller output could interfere with the reference signal and the secondary path dynamics may change during the operation. This interference problem can be resolved by using an infinite impulse response (IIR) filter which considers feedback of the one or more previous control signals to the controller output and the changing secondary path dynamics can be updated using an online modeling technique. In this paper, IIR filtering based filtered-U LMS (FULMS) controller is combined with online secondary path modeling algorithm to suppress the vibrations of a plate-like structure. The results are validated through numerical and experimental studies. The results show that the FULMS with online secondary path modeling approach has more vibration rejection capabilities with higher convergence rate than the FXLMS counterpart.

  18. Giant electrocaloric effect in PZT bilayer thin films by utilizing the electric field engineering

    Science.gov (United States)

    Zhang, Tiandong; Li, Weili; Cao, Wenping; Hou, Yafei; Yu, Yang; Fei, Weidong

    2016-04-01

    The enhancement of the electrocaloric effect (ECE) was achieved by the amplifying effect of applied electric field through devising the thin films' structure. The PbZr0.95Ti0.05O3/PbZr0.52Ti0.48O3 bilayer structured thin films were fabricated on a Pt(111)/Ti/SiO2/Si substrate using sol-gel method. The ΔS = 20.5 J K-1 kg-1 and ΔT = 24.8 K for bilayer thin films is achieved around 125 °C much below Tc, which is caused by the amplifying electric field induced phase transition of OAFE/RFE in PZr0.95Ti0.05O3 layer. It is also worth mentioning that the films exhibit outstanding ECE at room temperature; ΔS = 11.9 J K-1 kg-1 and ΔT = 10.7 K are observed, which are attributed to the effect of amplifying electric field in PbZr0.95Ti0.05O3 layer and RFE/TFE at morphotropic phase boundaries (MPB) in PbZr0.52Ti0.48O3 layer. This result indicates that to amplify the local electric field engineering and to maximize the number of coexisting phases in heterostructures or multilayer thin films may be an effective way for cooling applications.

  19. Effect of Heating Rate on Electromechanical Properties ofPNN–PZT Solid Solution

    Directory of Open Access Journals (Sweden)

    Virendra Singh

    2007-01-01

    Full Text Available Lead nickel niobate–lead zirconate titanate (Pb(Ni1/3Nb2/30.5 –Pb(Zr0.15Ti0.35O3, (PNN-PZTsolid solution was synthesised by columbite  process. Samples sintered at various heating ratesfor 4 h holding and their effect on electromechanical properties have been studied. When heatingrate was 8 °C/min from room temperature to 900 °C and holding for 4 h at 1280 °C, highest relativepermittivity and piezoelectric charge constant were observed, whereas heating rate of 3.5° C/min and holding for 4 h at 1280 °C have shown inferior electromechanical properties and graincoarsening. The piezoelectric charge constant (d33 ~612 pC/N and dielectric constant (e~ 5950observed in fast heating rate specimen as against to d33~ 137 pC/N and e~4294. XRD result showsthe formation of pyrochlore-free perovskite phase. Fine grains were observed  for fast heatingrate specimens.

  20. Effect of Sm Substitution on Structural, Dielectric, and Transport Properties of PZT Ceramics

    Directory of Open Access Journals (Sweden)

    Rajiv Ranjan

    2009-01-01

    Full Text Available The polycrystalline samples of Pb1−xSmx (Zr0.45Ti0.551−x/4O3 (PSZT (where x  =  0.00,  0.03,  0.06, and 0.09 were prepared by a high-temperature solid-state reaction technique. Preliminary X-ray structural analysis of the materials at room temperature has confirmed their formation in single-phase with tetragonal crystal structure. The temperature dependence of dielectric response of the samples at selected frequencies has exhibited their phase transition well above the room temperature. The variation of ac conductivity with temperature and the value of activation energy reveal that their conduction process is of mixed type (i.e., singly ionized in ferroelectric region and doubly ionized in paraelectric phase.

  1. Ferroelectric studies of excessive Sm3+ containing perovskite PZT and pyrochlore biphase ceramics

    Science.gov (United States)

    Babu, T. Anil; Ramesh, K. V.; Reddy, V. Raghavendra; Sastry, D. L.

    2014-04-01

    Polycrystalline samples of Sm3+ modified Pb1-x Sm2x/3 (Zr0.6Ti0.4) O3 (PSZT) ceramics (where x = 0.1, 0.2, 0.3, 0.4) have been prepared by a high energy ball milling technique, followed by calcination at 950°C and sintering at 1150°C. As x is increased more than 0.1 mole%, considerable secondary phase has been formed. This phase has been identified as pyrochlore Sm2Ti2O7 from its X-ray diffraction (XRD) peaks. The XRD studies also indicate that the perovskte phases of the present systems undergo a dopant induced phase transformation from rhombohedral to tetragonal strucure. All the samples exhibit diffuse but non-relaxor type ferroelectric phase transition. The results of dielectric and hysteresis studies of these materials are presented.

  2. Ferroelectric studies of excessive Sm{sup 3+} containing perovskite PZT and pyrochlore biphase ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Babu, T. Anil; Sastry, D. L., E-mail: dl-sastry@yahoo.com [Physics Department, Andhra University, Visakhapatnam - 530 003, AP (India); Ramesh, K. V. [Department of Engineering Physics, GITAM University, Visakhapatnam - 530 045, AP (India); Reddy, V. Raghavendra [UGC-DAE Consortium for Scientific Research, University Campus, Indore-452017, MP (India)

    2014-04-24

    Polycrystalline samples of Sm{sup 3+} modified Pb{sub 1−x} Sm{sub 2x/3} (Zr{sub 0.6}Ti{sub 0.4}) O{sub 3} (PSZT) ceramics (where x = 0.1, 0.2, 0.3, 0.4) have been prepared by a high energy ball milling technique, followed by calcination at 950°C and sintering at 1150°C. As x is increased more than 0.1 mole%, considerable secondary phase has been formed. This phase has been identified as pyrochlore Sm{sub 2}Ti{sub 2}O{sub 7} from its X-ray diffraction (XRD) peaks. The XRD studies also indicate that the perovskte phases of the present systems undergo a dopant induced phase transformation from rhombohedral to tetragonal strucure. All the samples exhibit diffuse but non-relaxor type ferroelectric phase transition. The results of dielectric and hysteresis studies of these materials are presented.

  3. Ultra high strain properties of lanthanum substituted PZT electro-ceramics prepared via mechanical activation

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Ajeet, E-mail: jkajeet@yahoo.co.in [Ceramics and Composites Group, Defence Metallurgical Research Laboratory, Hyderabad 500058 (India); School of Physics, University of Hyderabad, Hyderabad 500046 (India); Bhanu Prasad, V.V., E-mail: bhanu@dmrl.drdo.in [Ceramics and Composites Group, Defence Metallurgical Research Laboratory, Hyderabad 500058 (India); James Raju, K.C., E-mail: kcjrsp@yahoo.com [School of Physics, University of Hyderabad, Hyderabad 500046 (India); James, A.R., E-mail: james@dmrl.drdo.in [Ceramics and Composites Group, Defence Metallurgical Research Laboratory, Hyderabad 500058 (India)

    2014-06-25

    Highlights: • PLZT comparable with PMN–PT and their hot-pressed counterparts synthesized. • HEM applied for ceramic preparation at reduced sintering temperature. • Strain value (0.27%) comparable to previous reported values for PLZT 8/60/40. • The electric field induced (strain) hysteresis loss was also found to be very less. - Abstract: Substitution of lanthanum at the A sites of perovskite lead zirconate titanate ceramics shows an improvement in the structural and electrical properties. (Pb{sub 0.92}La{sub 0.08})(Zr{sub 0.60}Ti{sub 0.40})O{sub 3} (PLZT 8/60/40) was prepared using high energy mechano-chemical milling. The effect of milling on the microstructure and electrical properties of PLZT 8/60/40 has been studied. X-ray diffraction shows the phase formation after milling itself. TEM was used to measure the particle size. The SEM image of the sintered pellet shows a dense microstructure and the average grain size was found to be <1.5 μm. Electrical properties of the ceramics were characterized. Piezoelectric charge coefficient (d{sub 33}) was found to be 561 pC/N. Resonance studies were performed on poled ceramics and the electromechanical coupling factor was calculated by the resonance method. The PLZT 8/60/40 composition showed a well saturated and uniform P–E hysteresis loop with remanent polarization (P{sub r}) of 33.29 μC/cm{sup 2} and a coercive field (E{sub c}) of 10.57 kV/cm. Electric field induced strain (S–E loop) shows a value of ∼0.27% with minimum loss.

  4. The Influence of PZT Actuators Positioning in Active Structural Acoustic Control

    Directory of Open Access Journals (Sweden)

    P. Švec

    2007-01-01

    Full Text Available This paper deals with the effect of secondary actuator positioning in an active structural acoustics control (ASAC experiment. The ASAC approach is based on minimizing the sound radiation from structures to the far field by controlling the structural vibrations. In this article a rectangular steel plate structure was assumed with one secondary actuator attached to it. As a secondary actuator, a specially designed piezoelectric stripe actuator was used. We studied the effect of the position of the actuator on the pattern and on the radiated sound field of the structural vibration, with and without active control. The total radiated power was also measured. The experimental data was confronted with the results obtained by a numerical solution of the mathematical model used. For the solution, the finite element method in the ANSYS software package was used. 

  5. Damage detection in composite materials using PZT actuators and sensors for structural health monitoring

    Science.gov (United States)

    Spiegel, Michelle DuBose

    Structural Health Monitoring (SHM) of bridges, buildings, aircrafts, and spacecraft using a network of sensors has gained popularity over recent years. In this thesis, the use of piezoelectric actuators and sensors is described for detecting damage in a composite panel. The composite panels are fabricated using the Vacuum Assisted Resin Transfer Molding (VARTM) process. The panels are cut into small coupons (254 mm x 25.4 mm) to test various properties of the composite. A piezoelectric actuator is surface mounted on the composite coupon to generate Lamb waves while a surface mounted piezoelectric sensor measures the response. Data is collected from an undamaged composite coupon, and then the process is repeated for a damaged coupon. The existing damage is quantified by comparing the response of the damaged and undamaged composite coupons.

  6. Development of a MEMS-rate sensor with PZT actuation and sensing

    Science.gov (United States)

    Royle, Christopher M.; Fox, Colin H.

    2002-07-01

    This paper relates to the development of a novel rate sensor for a wide range of potential applications in the automotive field, amongst others. The sensor is based on the dynamic behavior of an active, vibrating silicon structure that uses thin-film piezoelectric material for actuation and sensing functions, and can be manufactured using silicon micro-machining techniques. The use of piezo-electric material for drive and pickoff offers potentially significant advantages over electrostatic/capacitive means in terms of achievable actuation forces and simplicity of structural design. This paper gives an overview of the design and analysis of a prototype sensor. The design concept is described and a low-order mathematical model, incorporating the inertial behavior of the structure and the interaction between the silicon structure and the piezo-drives and pickoffs is presented. This model allows the basic sensitivity of the sensor to be quantified. The design of a prototype sensor is then described. Some preliminary test results are presented, illustrating the feasibility of the concept.

  7. Phase and Texture Evolution in Chemically Derived PZT Thin Films on Pt Substrates

    Science.gov (United States)

    2014-09-01

    Thlefeld, GeoffL. Brennecka, Luz M. Sanchez, Ronald G. 5e. TASK NUMBER Polcawich, Jacob L. Jones 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAMES...Brennecka,¶ Luz M. Sanchez,k Ronald G. Polcawich,k and Jacob L. Jones‡‡,† ‡Department of Materials Science and Engineering, University of Florida, Gainesville

  8. Acoustic emission localization in plates with dispersion and reverberations using sparse PZT sensors in passive mode

    Science.gov (United States)

    Perelli, Alessandro; De Marchi, Luca; Marzani, Alessandro; Speciale, Nicolò

    2012-02-01

    A strategy for the localization of acoustic emissions (AE) in plates with dispersion and reverberation is proposed. The procedure exploits signals received in passive mode by sparse conventional piezoelectric transducers and a three-step processing framework. The first step consists in a signal dispersion compensation procedure, which is achieved by means of the warped frequency transform. The second step concerns the estimation of the differences in arrival time (TDOA) of the acoustic emission at the sensors. Complexities related to reflections and plate resonances are overcome via a wavelet decomposition of cross-correlating signals where the mother function is designed by a synthetic warped cross-signal. The magnitude of the wavelet coefficients in the warped distance-frequency domain, in fact, precisely reveals the TDOA of an acoustic emission at two sensors. Finally, in the last step the TDOA data are exploited to locate the acoustic emission source through hyperbolic positioning. The proposed procedure is tested with a passive network of three/four piezo-sensors located symmetrically and asymmetrically with respect to the plate edges. The experimentally estimated AE locations are close to those theoretically predicted by the Cramèr-Rao lower bound.

  9. Optimization of PZT Thin Film Crystalline Orientation Through Optimization of TiO2/Pt Templates

    Science.gov (United States)

    2011-01-01

    for evaluation of change in Ti deposition stability over time and the effect of substrate vender . .........................................8 Table 6...matrix #5 with fixed deposition conditions for evaluation of change in Ti deposition stability over time and the effect of substrate vender . The...Parallel Beam configurations 2. X-ray Source: sealed Cu anode tube, 2.2 kW, long fine line • Vender Name: ATPS, INC (Advanced Technical Products

  10. Controle ativo de estruturas reticuladas utilizando atuadores de pilha de pzt

    OpenAIRE

    Joventino, Carlos Fernando [UNESP

    2015-01-01

    Flexible structures, for instance, trusses, are present in many industrial applications and have a great importance in the daily lives of people, either in a single telecommunications antenna, or either in more sophisticated and accurate devices, such as satellites orbiting in space. This work presents the design and the construction of a smart flexible structure. The control design of this structure was obtained through the implementation of an integral force controller. The controller desig...

  11. Mechanically clamped PZT ceramics investigated by First-order reversal curves diagram

    Directory of Open Access Journals (Sweden)

    Laurentiu Stoleriu

    2010-09-01

    Full Text Available The First Order Reversal Curves (FORC diagrams method was developed for characterizing the switching properties of ferroelectrics. In the present paper, the FORC method was applied for hard Pb(Zr,TiO3 ceramics with symmetric and asymmetric clamping. An ideal high-oriented single-crystalline ferroelectric with rectangular P(E loop would be characterised by a delta-function FORC distribution, while real ferroelectrics and mostly the polycrystalline ceramics show dispersed FORC distributions. All the investigated ceramics show FORC distributions with non-Gaussian shape, slightly elongated along the coercitive axis, meaning a high dispersion of the energy barriers separating the two bi-stable polarizations ±P. The degree of dispersion is enhanced by clamping. The maximum FORC coercivity is located at ~ (1.9-2 MV/m for all the hard ceramics. The FORC cycling experiment causes the reversal of the initial poling and result in a positive/negative bias on the FORC diagrams. According to the observed features, it results that FORC coercivity is more related to the nature of the material, while the bias field is more sensitive to the electrical and mechanical boundary conditions in which the ferroelectric ceramics evolves while switching.

  12. Mechanical and Ferroelectric Response of Highly Textured PZT Films for Low Power MEMS

    Science.gov (United States)

    2012-10-01

    titanate films", Journal of Applied Physics , 89 (2), pp. 1336-1348, 2001. 4. Zavala, G., Fendler, J., Mckinstry, S. “Characterization of ferroelectric lead...zirconate titanate films by scanning force microscopy, Journal of Applied Physics , 81 (11), pp. 7480-7491, 1997. 5. Hidaka, T., et al

  13. Enhanced ferroeletric and piezoelectric properties of Nd3+ doped PZT nanoceramics

    Science.gov (United States)

    Kour, Paramjit; Pradhan, Sudipta Kishore; Kumar, Pawan; Sinha, Sanjay Kumar; Kar, Manoranjan

    2016-05-01

    The sol gel technique was used to prepare Pb1-xNdx Zr0.52Ti0.48O3 with x = 0.02, 0.04, 0.06 and 0.10 samples. Room temperature Raman spectra of all the sample were recorded in the range of wave number 30-1000 cm-1. It suggests that the increase in contribution of tetragonal crystallographic phase with the increase in Nd concentration in the sample. FTIR study shows the presence of characteristic bending and streching vibrations of perovskite (ABO3) structure. Ferroelectric and piezoelectric properties were enhanced by the Nd substitution at Pb site of PbZr0.52Ti0.48O3.

  14. Electrical imprint effects on far infrared (FIR) transmittance spectrum in PZT ferroelectric films

    Science.gov (United States)

    Vivas C., H.

    2015-06-01

    Tunable transmittance response in the 0.1-25 THz range for a lead Zirconate Titanate Ferroelectric film under imprint effects and surface anisotropy is calculated by adapting the classical Landau Devonshire theory and Rouard's method. Induced electrical field is introduced by modulating the P - E polarization profile, while the dielectric permittivity frequency dependence enters into the formalism by taking into account the soft phonon mode E(TO1) contribution in the framework of the Drude-Lorentz model. It is found that two optical states of light transmittance emerge at zero applied field and normal incidence, and the intensities of transmitted light are closely correlated with the strength of imprint and the path of the electrical polarization.

  15. Drop-by-drop deposition of ceramic slurry for fabrication of PZT microstructures

    Science.gov (United States)

    Klintberg, Lena; Thornell, Greger; Johansson, Stefan A. I.

    1999-10-01

    Most of the techniques available for ceramic microprocessing, e.g. tape casting, sputtering and sol-gel processing suffer from lack of geometrical flexibility although they often allow for good thickness control. With the interest for ceramic material in MST, especially the piezoelectric lead zirconate titanate, often involving more complex geometries, development of complementary technologies seems motivated.

  16. Piezoelectric and pyroelectric properties of Sr-doped PZT (PSZT) with minor manganese additions

    Science.gov (United States)

    Aleem, M. A.; Nawaz, H.; Shuaib, M.; Qaisar, S.; Akbar, M. S.

    2013-06-01

    A systematic study was performed to see the effect of Manganese addition and temperature gradient on the electrical properties of PSZT. Pb0.96 Sr0.04 (Zr0.52Ti0.48) O3 (PSZT) containing 0.3%, 0.5%, and 1% Mn was prepared by the sol gel method in order to ensure good stoichiometry and enhanced purity. The powders were calcined at 550 °C and sintered at 1200 °C to achieve 98% of the theoretical density. High field ac study was performed by (P-E) hysteresis measurements at different temperatures (RT, 60, 90, 120 and 150 °C) using an electric field up to 3 kV/mm. It was observed that for a lower Mn concentration P-E loops are pinched at the center while this constriction is found to decrease for greater concentrations. The optimized results were obtained for the 1 mol% of Mn content with 4 mol% of Sr. The values of Qm, k, d33 and tanδ were measured as 756, 0.38, 257 and 0.002 respectively. Higher temperatures coupled with a gradual increase of the electric field resulted in a shift of the hysteresis loops along electric field axis, indicating the presence of an internal bias field. Dependence of pyroelectric properties on applied electric field was also investigated. The value of pyroelectric coefficient was found maximum 6.25 × 10-4 (C/m2K) at 3 kV/mm.

  17. Study of harsh environment operation of flexible ferroelectric memory integrated with PZT and silicon fabric

    Science.gov (United States)

    Ghoneim, M. T.; Hussain, M. M.

    2015-08-01

    Flexible memory can enable industrial, automobile, space, and smart grid centered harsh/extreme environment focused electronics application(s) for enhanced operation, safety, and monitoring where bent or complex shaped infrastructures are common and state-of-the-art rigid electronics cannot be deployed. Therefore, we report on the physical-mechanical-electrical characteristics of a flexible ferroelectric memory based on lead zirconium titanate as a key memory material and flexible version of bulk mono-crystalline silicon (100). The experimented devices show a bending radius down to 1.25 cm corresponding to 0.16% nominal strain (high pressure of ˜260 MPa), and full functionality up to 225 °C high temperature in ambient gas composition (21% oxygen and 55% relative humidity). The devices showed unaltered data retention and fatigue properties under harsh conditions, still the reduced memory window (20% difference between switching and non-switching currents at 225 °C) requires sensitive sense circuitry for proper functionality and is the limiting factor preventing operation at higher temperatures.

  18. Development and Validation of an Enhanced Coupled-Field Model for PZT Cantilever Bimorph Energy Harvester

    Directory of Open Access Journals (Sweden)

    Long Zhang

    2013-01-01

    Full Text Available The power source with the limited life span has motivated the development of the energy harvesters that can scavenge the ambient environment energy and convert it into the electrical energy. With the coupled field characteristics of structure to electricity, piezoelectric energy harvesters are under consideration as a means of converting the mechanical energy to the electrical energy, with the goal of realizing completely self-powered sensor systems. In this paper, two previous models in the literatures for predicting the open-circuit and close-circuit voltages of a piezoelectric cantilever bimorph (PCB energy harvester are first described, that is, the mechanical equivalent spring mass-damper model and the electrical equivalent circuit model. Then, the development of an enhanced coupled field model for the PCB energy harvester based on another previous model in the literature using a conservation of energy method is presented. Further, the laboratory experiments are carried out to evaluate the enhanced coupled field model and the other two previous models in the literatures. The comparison results show that the enhanced coupled field model can better predict the open-circuit and close-circuit voltages of the PCB energy harvester with a proof mass bonded at the free end of the structure in order to increase the energy-harvesting level of the system.

  19. PZT-on-silicon RF-MEMS Lamb wave resonators and filters

    NARCIS (Netherlands)

    Yagubizade, Hadi

    2013-01-01

    Lamb-wave piezoelectric RF-MEMS resonators have demonstrated promising performance, such as low motional impedance and high Q-factor. Lamb-wave resonators are still in the perfectioning state and therefore there is a great demand for further understanding of various issues such as reducing the ancho

  20. Effect of Coprecipitation Parameters on Powder Characteristics and on Densification of PZT Ceramics.

    Science.gov (United States)

    1982-09-01

    34* diffraction using a Phillips Norelco Diffractometer with filtered Ni K radiati-n. The powders were also subjected to DTA and TGA analysis using... TGA analysis showed the first two peaks to be associated with weight loss, the maximum loss occurring near 300oC. From Fig. 4a it is evident that I0

  1. Effect of Powder Characteristics on Microstructure and Properties in Alkoxide Prepared PZT Ceramics.

    Science.gov (United States)

    1984-12-01

    The powders were also subjected to DTA and TGA analysis using a (DuPont 1090) Thermal Analysis System. Particle size distribution measurements were made...and 5300 C. TGA analysis showed the first two peaks to be associated with weight losses, the maximLn losses occurring near 3000C, and all weight loss

  2. Thermodynamic optimization of the PbO-ZrO{sub 2}-TiO{sub 2} (PZT) system and its application to the processing of composites of PZT ceramics and copper

    Energy Technology Data Exchange (ETDEWEB)

    Cancarevic, Marija

    2007-03-23

    The aim of this thesis was to obtain a consistent set of thermodynamic data for the Cu-Pb-Zr-Ti-O system, by means of the CALPHAD method, and then to calculate phase equilibria and chemical potential diagrams. The thermodynamic properties were described using the compound energy formalism (CEF) as well as the substitutional solution model for various solid phases and the associate model for the liquid phase, while the Redlich-Kister series were used to account for the interactions between species. Associate solution model adopted for the description of the liquid phase in the multicomponent Cu-Pb-Zr-Ti-O system was found to be superior for calculating the relevant phase equilibria in comparison with the twosublattice ionic model, although both models can be successfully applied to the binary systems (Zr-O, Ti-O, Cu-O, Pb-O). The ternary compound Cu{sub 2}PbO{sub 2} was modelled as a stoichiometric compound. Its thermodynamic properties were estimated by experiments. In the modelling of the ternary Cu-Ti-O system the three ternary compounds, Cu{sub 3}Ti{sub 3}O, Cu{sub 2}Ti{sub 4}O and Cu{sub 3}TiO{sub 4} were taken as stoichiometric compounds. PbTiO{sub 3} (tetragonal and cubic forms) and PbZrO{sub 3} (cubic form) were considered as stoichiometric compounds in the PbO-TiO{sub 2} and PbO-ZrO{sub 2} systems, while the tetragonal and orthorhombic PbO solid solutions were described by a substitutional model. The perovskite solid solution series, PbZr{sub x}Ti{sub 1-x}O{sub 3} was modelled as high temperature cubic form using the substitutional model. Calculated phase diagrams, i.e., predicted phase relations in the multicomponent Cu-Pb-Zr-Ti-O system (isobaric-isothermal sections and chemical potential diagrams) were checked experimentally. (orig.)

  3. Effects of Piezoelectric (PZT) Sensor Bonding and the Characteristics of the Host Structure on Impedance Based Structural Health Monitoring

    Science.gov (United States)

    Jalloh, Abdul

    2005-01-01

    This study was conducted to investigate the effects of certain factors on the impedance signal in structural health monitoring. These factors were: the quality of the bond between the sensor and the host structure, and the characteristics of the host structure, such as geometry, mass, and material properties. This work was carried out to answer a set of questions, related to these factors, that were developed by the project team. The project team was comprised of Dr. Doug Ramers and Dr. Abdul Jalloh of the Summer Faculty Fellowship Program, Mr. Arnaldo Colon- Perez, a student intern from the University of Puerto Rico of Turabo, and Mr. John Lassiter and Mr. Bob Engberg of the Structural and Dynamics Test Group at NASA Marshall Space Flight Center (MSFC). This study was based on a review of the literature on structural health monitoring to investigate the factors referred to above because there was not enough time to plan and conduct the appropriate tests at MSFC during the tenure of the Summer Faculty Fellowship Program project members. The surveyed literature documents works on structural health monitoring that were based on laboratory tests that were conducted using bolted trusses and other civil engineering type structures for the most part. These are not the typical types of structures used in designing and building NASA s space vehicles and systems. It was therefore recommended that tests be conducted using NASA type structures, such as pressure vessels, to validate the observations made in this report.

  4. Investigation of the Character of the Phase Transitions in Nb Doped Zr-rich PZT by Pyroelectric and Dielectric Measurements

    NARCIS (Netherlands)

    Cereceda, N.; Noheda, B.; Gonzalo, J.A.

    1999-01-01

    We present a study of the character of the phase transitions of the solid solution PbZr1-xTixO3. Using the spontaneous polarization curves we determined the mean-field parameters. These parameters show the first order character of the phase transitions for the richer Zr content and its evolution wit

  5. Properties of La and Nb-modified PZT thin films grown by radio frequency assisted pulsed laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Verardi, P. [CNR-Istituto di Acustica, Via del Fosso del Cavaliere 100, I-00133 Rome (Italy); Craciun, F. [CNR-Istituto dei Sistemi Complessi, Via del Fosso del Cavaliere 100, I-00133 Rome (Italy); Dinescu, M. [NILPRP, Bucharest, PO Box MG-16, RO-76900 (Romania)]. E-mail: dinescum@ifin.nipne.ro; Scarisoreanu, N. [NILPRP, Bucharest, PO Box MG-16, RO-76900 (Romania); Moldovan, A. [NILPRP, Bucharest, PO Box MG-16, RO-76900 (Romania); Purice, A. [NILPRP, Bucharest, PO Box MG-16, RO-76900 (Romania); Galassi, C. [CNR-ISTEC, Via Granarolo 64, I 48018 Faenza (Italy)

    2005-04-25

    Lead zirconate titanate ferroelectric thin films added with La and Nb has been grown by radio frequency assisted pulsed laser deposition on Pt/Si, starting from sintered targets. The dielectric properties were measured in a large frequency range and their dependence on the a.c. driving field amplitude has been investigated. A linear decreasing of the dielectric permittivity with frequency logarithm increasing has been evidenced. The most important factor for the driving field amplitude influence on the dielectric properties is the type of vacancies introduced by La and Nb substitutions, which indicates that the dynamics involved in a.c. field behavior is controlled by interaction mechanisms between ferroelectric domain or nanodomain walls and pinning (vacancies) centers.

  6. PZT-Based Detection of Compactness of Concrete in Concrete Filled Steel Tube Using Time Reversal Method

    Directory of Open Access Journals (Sweden)

    Shi Yan

    2014-01-01

    Full Text Available A smart aggregate-based approach is proposed for the concrete compactness detection of concrete filled steel tube (CFST columns. The piezoceramic-based smart aggregates (SAs were embedded in the predetermined locations prior to the casting of concrete columns to establish a wave-based smart sensing system for the concrete compactness detection purpose. To evaluate the efficiency of the developed approach, six specimens of the CFST columns with the rectangular cross-section were produced by placing some artificial defects during casting of concrete for simulating various uncompacted voids such as cavities, cracks, and debond. During the test, the time reversal technology was applied to rebuild the received signals and launch the reversed signals again by SAs, to overcome the issue of the lack of the prototype. Based on the proposed nonprototype, two indices of time reversibility (TR and symmetry (SYM were applied to relatively evaluate the level of concrete compactness in the range of the two SAs. The experimental results show that the developed method can effectively detect the compactness of concrete in CFST columns.

  7. Effect of Lanthanum Substitution on the Structural, dielectric, Ferroelectric and Piezoelectric Properties of Mechanically Activated PZt Electroceramics

    Directory of Open Access Journals (Sweden)

    Ajeet Kumar

    2016-06-01

    Full Text Available Different compositions of (Pb1-xLax (Zr0.60Ti0.40O3 (abbreviated as PLZT x/60/40; x=0, 0.07, 0.08 and 0.10 ceramics were prepared by a combinatorial approach by high energy mechano-chemical ball milling and cold isostatic pressing (CIP. X-ray diffraction patterns and transmission as well as scanning electron microscope were used for the micro-structural and morphological studies. The average particle size of PLZT milled powders was measured from the TEM images and was found to be in the nm range.XRD patterns of the sintered PLZT x/60/40 ceramics confirm the perovskite phase formation after heat treatment. SEM of sintered PLZT x/60/40 ceramics show a close packed dense structure. PLZT 8/60/40 ceramics show the fine grains (~1.3 µm with density ~97 per cent. Dielectric constant and loss were measured as a function of temperature. PLZT 8/60/40 ceramics shows the highest value of room temperature dielectric constant ~2480 at 1 kHz. Ferroelectric studies were done with the help of polarisation (P-E and strain (S-E vs. electric field measurements. PLZT 8/60/40 ceramics shows the maximum value of remnant polarisation (~36 µC/cm2 and strain (~0.27 per cent, respectively. PLZT x/60/40 ceramic samples were poled at optimized poling conditions. The measured values of piezoelectric charge coefficient (d33 and electromechanical coupling factor (kp of PLZT 8/60/40 ceramics were found to be, ~690 pC/N and ~71 per cent, respectively.

  8. PZT-like structural phase transitions in the BiFeO3-KNbO3 solid solution.

    Science.gov (United States)

    Lennox, Robert C; Taylor, Daniel D; Vera Stimpson, Laura J; Stenning, Gavin B G; Jura, Marek; Price, Mark C; Rodriguez, Efrain E; Arnold, Donna C

    2015-06-21

    Despite the high prominence of the perovskites BiFeO(3) and KNbO(3) the solid solution between the two has received little attention. We report a detailed neutron and synchrotron X-ray powder diffraction, and Raman spectroscopy study which demonstrates an R3c→P4mm→Amm2 series of structural phase transitions similar to that exhibited by the PbZrO(3)-PbTiO(3) solid solution.

  9. Electrical breakdown mechanics and reliability analysis for PZT piezoelectric ceramics%PZT电击穿机理研究及可靠性分析

    Institute of Scientific and Technical Information of China (English)

    王滨生; 安伟光; 张丹

    2008-01-01

    随着压电作动器的应用,对其可靠性的研究已成为一个比较重要的领域.压电堆是压电主动构件的核心作动单元,其电/力的失效(如电击穿、开裂)是影响压电装置性能和可靠性的2个方面.该文仅涉及压电陶瓷的电击穿方面,由于经典电击穿理论不能很好地适合工程应用,基于缺陷引起微短路符合Maxwell-Boltzmann分布的假设,建立击穿场强与体积的关系式,回归结果与实验数据基本吻合.在此基础上,建立了击穿场强的极限状态方程,并进行了可靠性分析.计算证明该方法是有效的.

  10. Sol-Gel法制备PZT铁电薄膜新进展%Advances of sol-gel derivation of PZT ferroelectric thin films

    Institute of Scientific and Technical Information of China (English)

    王福平; 姜兆华; 于艳菊; 赵连城

    2001-01-01

    从底电极的选择、过渡层的引入、外延膜的生长、取代阳离子的改性四个方面介绍了Sol-Gel法制备PZT铁电薄膜的研究进展,简述了PZT的Sol-Gel机理研究现状和引起PZT铁电薄膜极化疲劳的原因,分析了Sol-Gel法制备PZT铁电薄膜研究中存在的问题,并提出展望.

  11. Modeling of the attenuation of stress waves in concrete based on the Rayleigh damping model using time-reversal and PZT transducers

    Science.gov (United States)

    Tian, Zhen; Huo, Linsheng; Gao, Weihang; Li, Hongnan; Song, Gangbing

    2017-10-01

    Wave-based concrete structural health monitoring has attracted much attention. A stress wave experiences significant attenuation in concrete, however there is a lack of a unified method for predicting the attenuation coefficient of the stress wave. In this paper, a simple and effective absorption attenuation model of stress waves in concrete is developed based on the Rayleigh damping model, which indicates that the absorption attenuation coefficient of stress waves in concrete is directly proportional to the square of the stress wave frequency when the damping ratio is small. In order to verify the theoretical model, related experiments were carried out. During the experiments, a concrete beam was designed in which the d33-model piezoelectric smart aggregates were embedded to detect the propagation of stress waves. It is difficult to distinguish direct stress waves due to the complex propagation paths and the reflection and scattering of stress waves in concrete. Hence, as another innovation of this paper, a new method for computing the absorption attenuation coefficient based on the time-reversal method is developed. Due to the self-adaptive focusing properties of the time-reversal method, the time-reversed stress wave focuses and generates a peak value. The time-reversal method eliminates the adverse effects of multipaths, reflection, and scattering. The absorption attenuation coefficient is computed by analyzing the peak value changes of the time-reversal focused signal. Finally, the experimental results are found to be in good agreement with the theoretical model.

  12. Low voltage and high ON/OFF ratio field-effect transistors based on CVD MoS2 and ultra high-k gate dielectric PZT.

    Science.gov (United States)

    Zhou, Changjian; Wang, Xinsheng; Raju, Salahuddin; Lin, Ziyuan; Villaroman, Daniel; Huang, Baoling; Chan, Helen Lai-Wa; Chan, Mansun; Chai, Yang

    2015-05-21

    MoS2 and other atomic-level thick layered materials have been shown to have a high potential for outperforming Si transistors at the scaling limit. In this work, we demonstrate a MoS2 transistor with a low voltage and high ON/OFF ratio. A record small equivalent oxide thickness of ∼1.1 nm has been obtained by using ultra high-k gate dielectric Pb(Zr0.52Ti0.48)O3. The low threshold voltage (swing of 85.9 mV dec(-1), the high ON/OFF ratio of ∼10(8) and the negligible hysteresis ensure a high performance of the MoS2 transistor operating at 1 V. The extracted field-effect mobility of 1-10 cm(2) V(-1) s(-1) suggests a high crystalline quality of the CVD-grown MoS2 flakes. The combination of the two-dimensional layered semiconductor and the ultra high-k dielectric may enable the development of low-power electronic applications.

  13. Hydrostatic, uniaxial, and triaxial compression tests on unpoled "Chem-prep" PZT 95/5-2Nb ceramic within temperature range of -55 to 75 degrees C.

    Energy Technology Data Exchange (ETDEWEB)

    Zeuch, David Henry; Montgomery, Stephen Tedford; Lee, Moo Yul; Hofer, John H.

    2003-10-01

    Sandia is currently developing a lead-zirconate-titanate ceramic 95/5-2Nb (or PNZT) from chemically prepared ('chem-prep') precursor powders. Previous PNZT ceramic was fabricated from the powders prepared using a 'mixed-oxide' process. The specimens of unpoled PNZT ceramic from batch HF803 were tested under hydrostatic, uniaxial, and constant stress difference loading conditions within the temperature range of -55 to 75 C and pressures to 500 MPa. The objective of this experimental study was to obtain mechanical properties and phase relationships so that the grain-scale modeling effort can develop and test its models and codes using realistic parameters. The stress-strain behavior of 'chem-prep' PNZT under different loading paths was found to be similar to that of 'mixed-oxide' PNZT. The phase transformation from ferroelectric to antiferroelectric occurs in unpoled ceramic with abrupt increase in volumetric strain of about 0.7 % when the maximum compressive stress, regardless of loading paths, equals the hydrostatic pressure at which the transformation otherwise takes place. The stress-volumetric strain relationship of the ceramic undergoing a phase transformation was analyzed quantitatively using a linear regression analysis. The pressure (P{sub T1}{sup H}) required for the onset of phase transformation with respect to temperature is represented by the best-fit line, P{sub T1}{sup H} (MPa) = 227 + 0.76 T (C). We also confirmed that increasing shear stress lowers the mean stress and the volumetric strain required to trigger phase transformation. At the lower bound (-55 C) of the tested temperature range, the phase transformation is permanent and irreversible. However, at the upper bound (75 C), the phase transformation is completely reversible as the stress causing phase transformation is removed.

  14. Microestructura y propiedades de materiales cerámicos de PZT preparados a partir de polvo modificado superficialmente con fósforo.

    OpenAIRE

    Celi Apolo, Luis Alberto

    2000-01-01

    Desde el descubrimiento de la ferroelectricidad y de la piezoelectricidad en los materiales cerámicos, en la década de los cuarenta, se ha producido un continuo incremento de nuevos materiales y desarrollo de nuevas tecnologías que han dado lugar a un número signficativo de aplicaciones industriales y comerciales…

  15. Multiscale modeling for ferroelectric materials: identification of the phase-field model’s free energy for PZT from atomistic simulations

    Science.gov (United States)

    Völker, Benjamin; Landis, Chad M.; Kamlah, Marc

    2012-03-01

    Within a knowledge-based multiscale simulation approach for ferroelectric materials, the atomic level can be linked to the mesoscale by transferring results from first-principles calculations into a phase-field model. A recently presented routine (Völker et al 2011 Contin. Mech. Thermodyn. 23 435-51) for adjusting the Helmholtz free energy coefficients to intrinsic and extrinsic ferroelectric material properties obtained by DFT calculations and atomistic simulations was subject to certain limitations: caused by too small available degrees of freedom, an independent adjustment of the spontaneous strains and piezoelectric coefficients was not possible, and the elastic properties could only be considered in cubic instead of tetragonal symmetry. In this work we overcome such restrictions by expanding the formulation of the free energy function, i.e. by motivating and introducing new higher-order terms that have not appeared in the literature before. Subsequently we present an improved version of the adjustment procedure for the free energy coefficients that is solely based on input parameters from first-principles calculations performed by Marton and Elsässer, as documented in Völker et al (2011 Contin. Mech. Thermodyn. 23 435-51). Full sets of adjusted free energy coefficients for PbTiO3 and tetragonal Pb(Zr,Ti)O3 are presented, and the benefits of the newly introduced higher-order free energy terms are discussed.

  16. Long-Term Durability and Integrity of Built-In Piezoelectric-Based Active Sensing Network in Structures

    Science.gov (United States)

    2007-03-31

    reinforced bond is attached to the metal (Figure 57b and 57d) and its upper surface is coated with a layer of PZT crystals (Figure 57c and 57e ). It is...temperature approach: (a) picture of a PZT before and after CNTs growth, (b) SRM image of the PZT after CNTs growth. Figure 37. SEM images of CNTs

  17. Processing and properties of lead zirconate titanate thin films on gallium nitride and ruthenium by sol-gel and chemical vapor deposition

    Science.gov (United States)

    Cao, Wei

    The Pb(ZrxTi1-x)O3 (PZT) thin films are potential candidates for ferroelectric random access memory (FeRAM) devices and components for microelectromechanical systems (MEMS). For example, the PZT/GaN system is being explored as RF MEMS devices for insertion in RF communication systems. A reproducible sol-gel process was developed for the deposition of PZT films on wurtzite (0001) GaN/sapphire substrates. The composition, crystallography, and interfacial nanochemistry were evaluated by various characterization techniques. The PZT/GaN heterostructure exhibited a chemically sharp interface with insignificant interdiffusion between PZT and GaN layers. However, PZT in metal -ferroelectric -semiconductor (MFS) configuration showed lower capacitance and asymmetrical polarization hysteresis compared to PZT in metal-ferroelectric-metal configuration. Such a deviation was attributed to the high depolarization field (Edepol) within PZT. To mitigate this issue, a two-pronged approach was used. First, the calculated spatial distribution of the electric field and potential, which stem from all the charge densities within the MFS configuration, demonstrated that by adjusting controllable parameters, one can minimize Edepol and maximize polarization. Second, a robust metal-organic chemical vapor deposition (MOCVD) process was developed to fabricate high quality PZT thin films on GaN. In this experimental approach, phase-pure and highly (111) oriented PZT films were deposited on GaN/sapphire substrates by MOCVD. The orientation relationships of PZT/GaN system were determined using x-ray pole figure and high-resolution transmission electron microscopy (TEM). The nanochemistry of the PZT/GaN interface, studied using analytical TEM, indicated a chemically sharp interface with interdiffusion limited to a region below 5 nm. The properties of MOCVD-PZT on GaN are briefly compared with PZT by sol-gel processing, rf sputtering, and pulsed laser deposition. Additionally, a preliminary study

  18. Research on Raman-scattering and Fabrication of Multilayer Thin Film with Different Structures and Components Based on Pt/Ti/Si3N4/SiO2/Si Substrate

    Institute of Scientific and Technical Information of China (English)

    Qiu-lin Tan; Wen-dong Zhang; Chen-yang Xue; Jun Liu; Jun-hong Li; Ji-jun Xiong

    2009-01-01

    Using the same conditions and various starting materials, such as lead acetate trihydrate, tetrabulyl titanate, zirconium n-butoxide, and acetylacetone, two kinds of solid precursors, lead zirconate titanate (PZT, Zr/Ti=15/85) and lead titanate (PT), were fabricated. With three different combinations, namely, PZT, PT/PZT-PZT/PT, and PT/PZT/-/PZT/PT, three multilayer thin films were deposited on three Pt-Ti-Si3N4-SiO2-Si substrates by a modified sol-gel process. The fabrication process of the thin films is discussed in detail. We found that there is a large built-in stress in the thin film, which can be diminished by annealing at 600 ℃, when the gel is turned into solid material through drying and sintering. The Raman scattering spectra of the films with different compositions and structures were investigated. With the help of X-ray diffraction (XRD) analyzer and Raman scattering spectra analyzer, it was found that the thin films with the PT/PZT-PZT/PT structure have reasonable crystallinity and less residual stress. XRD testing shows that the diffraction pattern of the multilayer film results from the superimposition of the PZT and PT patterns. This leads to the conclusion that the PT/PZT-PZT/PT multilayer thin film has a promising future in pyroelectric infrared detectors with high performance.

  19. La0.7Sr0.3MnO3-PZT双层膜中的磁电耦合%Magnetoelectric Coupling in Bilayers of La0.7Sr0.3MnO3-PZT

    Institute of Scientific and Technical Information of China (English)

    杨全民; 张宁

    2006-01-01

    讨论了La0.7Sr0.3MnO3-Pb(Zr,Ti)O3双层膜的磁电(ME)效应.La0.7Sr0.3MnO3粉料由溶胶-凝胶法制成,经1300 K热压并在1573 K高温下烧结而成.在该双层膜中测量到了很强的磁电相互作用.相较于厚膜型(tape casting)复合样品,该双层膜显示出更为优良的ME耦合.反映其ME耦合效应强弱的电压系数αE是在一定的磁场、温度和频率下测得的.横向耦合要比纵向耦合更为强烈,并在225 K时ME电压系数达到峰值.分析表明由磁场和频率变化导致的ME系数变化的实验值与理论值符合的很好.

  20. Motion Mechanism of Two-Degree-of-Freedom Spherical Motor Using Single PZT Vibrator%单振子二自由度球面马达的运动机理

    Institute of Scientific and Technical Information of China (English)

    程光明; 郭抗; 孙业明; 曾平; 武迪

    2011-01-01

    利用矩形板形压电振子的两种振动模态,构建了一种采用单片压电振子驱动球形转子,形成两个旋转自由度的压电球面超声马达,对马达的作用机理进行了仿真分析和试验验证.利用有限元法对马达的矩形板压电振子的振动模态、共振频率进行了分析计算,仿真结果表明矩形板压电振子能够形成振型清晰的B32和B23振动模态,模态频率分别为49.127 kHz和49.756 kHz.对压电振子上每个凸起与球形转子之间的接触点的运动轨迹进行了计算机仿真,并对仿真结果进行了试验验证.分析结果表明各接触点能有效形成时序合理的椭圆运动轨迹,作为支撑足的一组凸起的变形量占作为驱动足的一组凸起的变形量的30%,能够用于驱动球形转子形成二自由度转动.仿真分析和试验结果证明了二自由度球面马达球形转子形成二维运动的作用机理.%A two-degree-of-freedom piezoelectric spherical ultrasonic motor using only one piezoelectric element to drive the rotator was proposed based on two vibration modes of a rectangular plate type piezoelectric vibrator. The motion mechanism of the motor was verified by simulation and experiment. The vibration modes and resonance frequencies of the motor's plate type piezoelectric vibrator were calculated by finite element method. The simulation results show that the piezoelectric vibrator can produce clear vibration shapes in B32 and BB modes, and their modal frequencies are 49.127 kHz and 49.756 kHz, respectively. The motion trajectories of four contact points between the protrusion and the spherical rotor were analyzed with computer simulation, and prototype test was carried out to verify the simulation results. The results indicate that the four contact points can form elliptical trajectories with reasonable timing, which can be used to drive the spherical rotor to form rotation with two-degree-of-freedom, and the deformation of protrusions which act as support feet is 30% of that of protrusions that act as drive feet. The simulation and experimental results confirm the formation of two-dimensional motion mechanism of the two-degree-of-freedom spherical motor.

  1. Piezoelectric properties of the new generation active matrix hybrid (micro-nano) composites

    Science.gov (United States)

    Parali, Levent; Şabikoğlu, İsrafil; Kurbanov, Mirza A.

    2014-11-01

    A hybrid piezoelectric composite structure is obtained by addition of nano-sized BaTiO3, SiO2 to the micro-sized PZT and polymers composition. Although the PZT material itself has excellent piezoelectric properties, PZT-based composite variety is limited. Piezoelectric properties of PZT materials can be varied with an acceptor or a donor added to the material. In addition, varieties of PZT-based sensors can be increased with doping polymers which have physical-mechanical, electrophysical, thermophysical and photoelectrical properties. The active matrix hybrid structure occurs when bringing together the unique piezoelectric properties of micro-sized PZT with electron trapping properties of nano-sized insulators (BaTiO3 or SiO2), and their piezoelectric, mechanic and electromechanic properties significantly change. In this study, the relationship between the piezoelectric constant and the coupling factor values of microstructure (PZT-PVDF) and the hybrid structure (PZT-PVDF-BaTiO3) composite are compared. The d33 value and the coupling factor of the hybrid structure have shown an average of 54 and 62% increase according to microstructure composite, respectively. In addition, the d33 value and the coupling factor of the hybrid structure (PZT-HDPE-SiO2) have exhibited about 68 and 52% increase according to microstructure composite (PZT-HDPE), respectively.

  2. Damping properties of epoxy-based composite embedded with sol–gel-derived Pb(Zr0.53Ti0.47)O3 thin film with different thicknesses

    Indian Academy of Sciences (India)

    Guo Dongyun; Mao Wei; Qin Yan; Huang Zhixiong; Wang Chuanbin; Shen Qiang; Zhang Lianmeng

    2012-06-01

    Pb(Zr0.53Ti0.47)O3 (PZT) thin films were prepared on Pt/Ti/SiO2/Si substrate by sol–gel method. The effect of film thickness on microstructure, ferroelectric and dielectric properties was investigated. The single-phase PZT films were obtained with different thicknesses. PZT films with a thickness of 190–440 nm had better dielectric and ferroelectric properties. The epoxy/PZT film/epoxy sandwiched composites were prepared. The thickness of PZT films influenced their damping properties of the composites, and the epoxy-based composites embedded with 310 nm-thick PZT films had the largest damping loss factor of 0.915.

  3. Tuning and Persistent Switching of Graphene Plasmons on a Ferroelectric Substrate.

    Science.gov (United States)

    Goldflam, Michael D; Ni, Guang-Xin; Post, Kirk W; Fei, Zhe; Yeo, Yuting; Tan, Jun You; Rodin, Aleksandr S; Chapler, Brian C; Özyilmaz, Barbaros; Castro Neto, Antonio H; Fogler, Michael M; Basov, D N

    2015-08-12

    We characterized plasmon propagation in graphene on thin films of the high-κ dielectric PbZr0.3Ti0.7O3 (PZT). Significant modulation (up to ±75%) of the plasmon wavelength was achieved with application of ultrasmall voltages (< ±1 V) across PZT. Analysis of the observed plasmonic fringes at the graphene edge indicates that carriers in graphene on PZT behave as noninteracting Dirac Fermions approximated by a semiclassical Drude response, which may be attributed to strong dielectric screening at the graphene/PZT interface. Additionally, significant plasmon scattering occurs at the grain boundaries of PZT from topographic and/or polarization induced graphene conductivity variation in the interior of graphene, reducing the overall plasmon propagation length. Lastly, through application of 2 V across PZT, we demonstrate the capability to persistently modify the plasmonic response of graphene through transient voltage application.

  4. Enhanced Magnetoelectric Effect in Permendur/Pb(Zr0.52Ti0.48O3 Laminated Magnetostrictive/Piezoelectric Composite

    Directory of Open Access Journals (Sweden)

    Yanmin Jia

    2015-09-01

    Full Text Available In this work, after investigating three typical magneto-electric (ME composites, Permendur/Pb(Zr0.52Ti0.48O3(PZT, Metglas/PZT, and Tefenol-D/PZT, with the same dimensions and different saturation magnetostriction and magnetic permeability, the most excellent ME performance is observed in the Permendur/PZT laminates, which agrees well with the predicted results from the figure of merit. The low-frequency and resonance ME coefficients of Permendur/PZT composite are ~23.1 V/Oe.cm and ~309 V/Oe.cm at the optimal dc bias magnetic field of ~250 Oe, respectively. The strong ME effect of Permendur/PZT composite gives it potential in practical magnetic sensitive device applications.

  5. Room-temperature poling of PbTiO3/Pb(Zr,Ti)O3 sol-gel composite films by pulse discharge

    Science.gov (United States)

    Kouyama, Hikaru; Kibe, Taiga; Fujimoto, Shota; Namihira, Takao; Kobayashi, Makiko

    2016-07-01

    The PbTiO3/Pb(Zr,Ti)O3 (PT/PZT) sol-gel composite is a promising piezoelectric material because of its high piezoelectricity and temperature stability up to 360 °C. However, the poling of PT/PZT required high temperature owing to the high coercive field of PT, which made the poling of PT/PZT troublesome. In this research, conventional DC corona poling and pulse discharge at room temperature were attempted for PT/PZT samples. As a result, PT/PZT poled by pulse discharge generation at room temperature showed comparable ultrasonic responses to that poled by DC corona discharge generation at a high temperature. Therefore, room-temperature poling of PT/PZT was successfully carried out by pulse discharge, and poling time was markedly reduced from ˜15 min to 15 s.

  6. Characterization of highly (110)- and (111)-oriented Pb(Zr ,Ti)O3 films on BaPbO3 electrode using Ru conducting barrier

    Science.gov (United States)

    Liang, Chun-Sheng; Wu, Jenn-Ming

    2005-07-01

    Highly non-(001)-oriented Pb(Zr ,Ti)O3 (PZT) films have been fabricated by rf-magnetron sputtering. The preferential (110)-oriented BaPbO3 (BPO) deposited on Ru buffer layer induces the growth of (110)-oriented PZT film. With the aid of self-organized growth of PZT, the orientation of the film deposited on random-oriented BPO /Pt(111)/Ru(002) is (111)-preferred. The insertion of Pt layer between BPO and Ru changes the orientation of PZT from (110) to (111) and prevents the oxygen diffusion. These non-(001)-oriented PZT films possess more superior ferroelectric, fatigue, and retention properties than those of (001)-oriented PZT films.

  7. A multi-feature integration method for fatigue crack detection and crack length estimation in riveted lap joints using Lamb waves

    Data.gov (United States)

    National Aeronautics and Space Administration — This paper presents an experimental study of damage detection and quantification in riveted lap joints. Embedded lead zirconate titanate piezoelectric (PZT) ceramic...

  8. Scalable synthesis of morphotropic phase boundary lead zirconium titanate nanowires for energy harvesting.

    Science.gov (United States)

    Zhou, Zhi; Tang, Haixiong; Sodano, Henry A

    2014-12-03

    Lead zirconium titanate (PZT) nanowires are synthesized using a scalable two-step hydrothermal reaction. The piezo-electric coupling coefficient of the PZT NWs shows the highest value for PZT nano-wires in the literature (80 ± 5 pm/V). A PZT-NW-based nanocomposite is fabri-cated to demonstrate an energy-harvesting application with an open-circuit voltage up to 7 V and a power density up to 2.4 μW/cm(3) .

  9. Design of a piezoelectric transducer cylindrical phase modulator for simulating acoustic emission signals

    Institute of Scientific and Technical Information of China (English)

    HE Cunfu; HANG Lijun; WU Bin

    2007-01-01

    To conveniently carry out the pipeline leak experiment in a laboratory,leak acoustic signals are simulated by using the converse piezoelectric effect of a piezoelectric transducer (PZT) cylindrical phase modulator.On the basis of the piezoelectric equations and electromechanical equivalence principle,the transfer function of a PZT cylindrical phase modulator is delivered.A PZT cylindrical phase modulator is designed,and the numerical simulation is conducted.Results prove that the PZT cylindrical phase modulator can effectively simulate leak acoustic emission signals when the frequency is lower than 25 KHz.

  10. Comparison of effective transverse piezoelectric coefficients e31,f of Pb(Zr,Ti)O3 thin films between direct and converse piezoelectric effects

    Science.gov (United States)

    Tsujiura, Yuichi; Kawabe, Saneyuki; Kurokawa, Fumiya; Hida, Hirotaka; Kanno, Isaku

    2015-10-01

    We evaluated the effective transverse piezoelectric coefficients (e31,f) of Pb(Zr,Ti)O3 (PZT) thin films from both the direct and converse piezoelectric effects of unimorph cantilevers. (001) preferentially oriented polycrystalline PZT thin films and (001)/(100) epitaxial PZT thin films were deposited on (111)Pt/Ti/Si and (001)Pt/MgO substrates, respectively, by rf-magnetron sputtering, and their piezoelectric responses owing to intrinsic and extrinsic effects were examined. The direct and converse |e31,f| values of the polycrystalline PZT thin films were calculated as 6.4 and 11.5-15.0 C/m2, respectively, whereas those of the epitaxial PZT thin films were calculated as 3.4 and 4.6-4.8 C/m2, respectively. The large |e31,f| of the converse piezoelectric property of the polycrystalline PZT thin films is attributed to extrinsic piezoelectric effects. Furthermore, the polycrystalline PZT thin films show a clear nonlinear piezoelectric contribution, which is the same as the Rayleigh-like behavior reported in bulk PZT. In contrast, the epitaxial PZT thin films on the MgO substrate show a piezoelectric response owing to the intrinsic and linear extrinsic effects, and no nonlinear contribution was observed.

  11. Pyroelectric response of lead zirconate titanate thin films on silicon: Effect of thermal stresses

    Energy Technology Data Exchange (ETDEWEB)

    Kesim, M. T.; Zhang, J.; Alpay, S. P. [Department of Materials Science and Engineering and Institute of Materials Science, University of Connecticut, Storrs, Connecticut 06269 (United States); Trolier-McKinstry, S. [Department of Materials Science and Engineering and Materials Research Institute, Pennsylvania State University, Pennsylvania 16802 (United States); Mantese, J. V. [United Technologies Research Center, East Hartford, Connecticut 06118 (United States); Whatmore, R. W. [Tyndall National Institute, Lee Maltings, Dyke Parade, Cork City, County Cork (Ireland)

    2013-11-28

    Ferroelectric lead zirconate titanate [Pb(Zr{sub x}Ti{sub 1-x}O){sub 3}, (PZT x:1-x)] has received considerable interest for applications related to uncooled infrared devices due to its large pyroelectric figures of merit near room temperature, and the fact that such devices are inherently ac coupled, allowing for simplified image post processing. For ferroelectric films made by industry-standard deposition techniques, stresses develop in the PZT layer upon cooling from the processing/growth temperature due to thermal mismatch between the film and the substrate. In this study, we use a non-linear thermodynamic model to investigate the pyroelectric properties of polycrystalline PZT thin films for five different compositions (PZT 40:60, PZT 30:70, PZT 20:80, PZT 10:90, PZT 0:100) on silicon as a function of processing temperature (25–800 °C). It is shown that the in-plane thermal stresses in PZT thin films alter the out-of-plane polarization and the ferroelectric phase transformation temperature, with profound effect on the pyroelectric properties. PZT 30:70 is found to have the largest pyroelectric coefficient (0.042 μC cm{sup −2} °C{sup −1}, comparable to bulk values) at a growth temperature of 550 °C; typical to what is currently used for many deposition processes. Our results indicate that it is possible to optimize the pyroelectric response of PZT thin films by adjusting the Ti composition and the processing temperature, thereby, enabling the tailoring of material properties for optimization relative to a specific deposition process.

  12. Bending strength of piezoelectric ceramics and single crystals for multifunctional load-bearing applications.

    Science.gov (United States)

    Anton, Steven R; Erturk, Alper; Inman, Daniel

    2012-06-01

    The topic of multifunctional material systems using active or smart materials has recently gained attention in the research community. Multifunctional piezoelectric systems present the ability to combine multiple functions into a single active piezoelectric element, namely, combining sensing, actuation, or energy conversion ability with load-bearing capacity. Quantification of the bending strength of various piezoelectric materials is, therefore, critical in the development of load-bearing piezoelectric systems. Three-point bend tests are carried out on a variety of piezoelectric ceramics including soft monolithic piezoceramics (PZT-5A and PZT-5H), hard monolithic ceramics (PZT-4 and PZT-8), single-crystal piezoelectrics (PMN-PT and PMN-PZT), and commercially packaged composite devices (which contain active PZT-5A layers). A common 3-point bend test procedure is used throughout the experimental tests. The bending strengths of these materials are found using Euler-Bernoulli beam theory to be 44.9 MPa for PMN-PZT, 60.6 MPa for PMN-PT, 114.8 MPa for PZT- 5H, 123.2 MPa for PZT-4, 127.5 MPa for PZT-8, 140.4 MPa for PZT-5A, and 186.6 MPa for the commercial composite. The high strength of the commercial configuration is a result of the composite structure that allows for shear stresses on the surfaces of the piezoelectric layers, whereas the low strength of the single-crystal materials is due to their unique crystal structure, which allows for rapid propagation of cracks initiating at flaw sites. The experimental bending strength results reported, which are linear estimates without nonlinear ferroelastic considerations, are intended for use in the design of multifunctional piezoelectric systems in which the active device is subjected to bending loads.

  13. Analysis of axisymmetric and non-axisymmetric wave propagation in a homogeneous piezoelectric solid circular cylinder of transversely isotropic material

    CSIR Research Space (South Africa)

    Shatalov, MY

    2010-01-01

    Full Text Available for PZT-4 and PZT-7A piezoelectric ceramics for circumferential wave numbers m = 1, 2, and 3. It is observed that the dispersion curves are sensitive to the type of the imposed boundary conditions as well as to the measure of the electromechanical coupling...

  14. Analysis of non-axisymmetric wave propagation in a homogeneous piezoelectric solid circular cylinder of transversely isotropic material

    CSIR Research Space (South Africa)

    Shatalov, MY

    2009-01-01

    Full Text Available for PZT-4 and PZT-7A piezoelectric ceramics for circumferential wave numbers m = 1, 2, and 3. It is observed that the dispersion curves are sensitive to the type of the imposed boundary conditions as well as to the measure of the electromechanical coupling...

  15. Stability of the monoclinic phase in the ferroelectric perovskite PbZr1-xTixO3

    NARCIS (Netherlands)

    Noheda, B.; Cox, D.E.; Shirane, G.; Guo, R.; Jones, B.; Cross, L.E.

    2000-01-01

    Recent structural studies of ferroelectric PbZr1-xTixO3 (PZT) with x=0.48, have revealed a monoclinic phase in the vicinity of the morphotropic phase boundary (MPB), previously regarded as the boundary separating the rhombohedral and tetragonal regions of the PZT phase diagram. In the present paper,

  16. Elastodynamic Impact into Piezoelectric Media

    Science.gov (United States)

    2014-09-01

    boundary condition to the problem of elastodynamic impact into a lead zirconate titanate (PZT-4) target and find that the solutions obtained using... titanate (PZT-4) target are compared with solutions obtained using a finite-difference time-domain (FDTD) code and the commercial finite element (FE

  17. Piezoelectric and mechanical properties of structured PZT–epoxy composites

    NARCIS (Netherlands)

    Kunnamkuzhakkal James, N.; Van den Ende, D.; Lafont, U.; Van der Zwaag, S.; Groen, W.A.

    2013-01-01

    Structured lead zirconium titanate (PZT)–epoxy composites are prepared by dielectrophoresis. The piezoelectric and dielectric properties of the composites as a function of PZT volume fraction are investigated and compared with the corresponding unstructured composites. The effect of poling voltage o

  18. Fiber Ring Laser In-cavity Phase Modulation

    Institute of Scientific and Technical Information of China (English)

    YU Benli; QIAN Jingren; LUO Jiatong; YANG Yinghai

    2001-01-01

    In this paper, experimental results of the in-cavity phase modulation induced by dithering PZT is reported. The dithering PZT can produce strong phase modulation, reshaping the laser output spectrum, but does not affect the laser linewidth, which is measured by homodyne method.

  19. Fabrication and Characterization of a Lead Zirconate Titanate Micro Energy Harvester Based on Eutectic Bonding

    Institute of Scientific and Technical Information of China (English)

    LI Yi-Gui; SUN Jian; YANG Chun-Sheng; LIU Jing-Quan; SUGIYAMA Susumu; TANAKA Katsuhiko

    2011-01-01

    A lead zirconate titanate(PZT)-Si energy harvester cantilever with PZT bulk ceramics is fabricated by eutectic bonding, polishing and dicing processes. The feasibility of this process is studied using a successful operation of the cantilever in both actuation and harvesting modes. The first prototype made from a PZT-Au-Si cantiliever is tested. The testing results show the voltage output of 632mV at the frequency of 815Hz when the excitation acceleration is 0.5 g. The PZT and silicon layers are bonded together to form a sandwiched structure using a gold layer as an intermediate layer.%@@ A lead zirconate titanate(PZT)-Si energy harvester cantilever with PZT bulk ceramics is fabricated by eutectic bonding, polishing and dicing processes.The feasibility of this process is studied using a successful operation of the cantilever in both actuation and harvesting modes.The first prototype made from a PZT-Au-Si cantiliever is tested.The testing results show the voltage output of 632mV at the frequency of 815 Hz when the excitation acceleration is 0.5 g.The PZT and silicon layers are bonded together to form a sandwiched structure using a gold layer as an intermediate layer.

  20. Integrated Micro-scale Power Conversion

    Science.gov (United States)

    2012-08-01

    extensional mode Plate thickness mode Ring extensional mode J. Yang, IEEE TUFFC, 2007. Anchor Anchor Equivalent circuit model Port 2...PZT Si PZT Simo o E E t t kQ nRR R 1 1 2 1 1 ’’ ’’ 31 2 22  Power handling • Critical vibration amplitude, xcr, from a critical strain, ecr

  1. Load sensor

    NARCIS (Netherlands)

    Van den Ende, D.; Almeida, P.M.R.; Dingemans, T.J.; Van der Zwaag, S.

    2007-01-01

    The invention relates to a load sensor comprising a polymer matrix and a piezo-ceramic material such as PZT, em not bedded in the polymer matrix, which together form a compos not ite, wherein the polymer matrix is a liquid crystalline resin, and wherein the piezo-ceramic material is a PZT powder for

  2. (001) Oriented piezoelectric films prepared by chemical solution deposition on Ni foils

    Energy Technology Data Exchange (ETDEWEB)

    Yeo, Hong Goo, E-mail: hxy162@psu.edu; Trolier-McKinstry, Susan [Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States)

    2014-07-07

    Flexible metal foil substrates are useful in some microelectromechanical systems applications including wearable piezoelectric sensors or energy harvesters based on Pb(Zr,Ti)O₃ (PZT) thin films. Full utilization of the potential of piezoelectrics on metal foils requires control of the film crystallographic texture. In this study, (001) oriented PZT thin films were grown by chemical solution deposition (CSD) on Ni foil and Si substrates. Ni foils were passivated using HfO₂ grown by atomic layer deposition in order to suppress substrate oxidation during subsequent thermal treatment. To obtain the desired orientation of PZT film, strongly (100) oriented LaNiO₃ films were integrated by CSD on the HfO₂ coated substrates. A high level of (001) LaNiO₃ and PZT film orientation were confirmed by X-ray diffraction patterns. Before poling, the low field dielectric permittivity and loss tangents of (001) oriented PZT films on Ni are near 780 and 0.04 at 1 kHz; the permittivity drops significantly on poling due to in-plane to out-of-plane domain switching. (001) oriented PZT film on Ni displayed a well-saturated hysteresis loop with a large remanent polarization ~36 μC/cm², while (100) oriented PZT on Si showed slanted P-E hysteresis loops with much lower remanent polarizations. The |e{sub 31,f}| piezoelectric coefficient was around 10.6 C/m² for hot-poled (001) oriented PZT film on Ni.

  3. Hydrothermal synthesis of Pb(Zr0.52Ti0.48)O3 powders at low temperature and low alkaline concentration

    Indian Academy of Sciences (India)

    Zhong-Cheng Qiu; Jian-Ping Zhou; Gangqiang Zhu; Peng Liu; Xiao-Bing Bian

    2009-04-01

    Pb(Zr0.52Ti0.48)O3 (PZT) powders were prepared by hydrothermal method. The effects of experimental parameters, including Pb/(Zr, Ti) ratio, alkaline concentration, reaction temperature and time on the product powders were studied in detail. Pure PZT powders were synthesized at suitable experimental conditions and Raman spectra confirmed the PZT with a perovskite-type structure. The homogeneous PZT powders with cubic-shaped morphology were formed at alkaline concentration of 1.2 M after reacting at 230°C for 2 h. The pure PZT powders obtained at low temperature and low alkaline concentration were attributed to precursors, TiCl4, with high activity and mineralizer NaOH with small cation radius.

  4. Improvement of Pyroelectric Cells for Thermal Energy Harvesting

    Directory of Open Access Journals (Sweden)

    Jing-Chih Ciou

    2012-01-01

    Full Text Available This study proposes trenching piezoelectric (PZT material in a thicker PZT pyroelectric cell to improve the temperature variation rate to enhance the efficiency of thermal energy-harvesting conversion by pyroelectricity. A thicker pyroelectric cell is beneficial in generating electricity pyroelectrically, but it hinders rapid temperature variations. Therefore, the PZT sheet was fabricated to produce deeper trenches to cause lateral temperature gradients induced by the trenched electrode, enhancing the temperature variation rate under homogeneous heat irradiation. When the trenched electrode type with an electrode width of 200 μm and a cutting depth of 150 μm was used to fabricate a PZT pyroelectric cell with a 200 μm thick PZT sheet, the temperature variation rate was improved by about 55%. Therefore, the trenched electrode design did indeed enhance the temperature variation rate and the efficiency of pyroelectric energy converters.

  5. Negligible substrate clamping effect on piezoelectric response in (111)-epitaxial tetragonal Pb(Zr, Ti)O{sub 3} films

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Tomoaki, E-mail: t-yamada@nucl.nagoya-u.ac.jp [Department of Materials, Physics and Energy Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); PRESTO, Japan Science and Technology Agency, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Yasumoto, Jun; Ito, Daisuke; Yoshino, Masahito; Nagasaki, Takanori [Department of Materials, Physics and Energy Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Sakata, Osami [Synchrotron X-ray Station at SPring-8 and Synchrotron X-ray Group, National Institute for Materials Science, Sayo-cho, Sayo-gun, Hyogo 679-5148 (Japan); Department of Innovative and Engineered Material, Tokyo Institute of Technology, Yokohama 226-8503 (Japan); Imai, Yasuhiko [Japan Synchrotron Radiation Research Institute, SPring-8, Sayo-cho, Sayo-gun, Hyogo 679-5198 (Japan); Kiguchi, Takanori [Institute for Materials Research, Tohoku University, Sendai, Miyagi 980-8577 (Japan); Shiraishi, Takahisa; Shimizu, Takao; Funakubo, Hiroshi [Department of Innovative and Engineered Material, Tokyo Institute of Technology, Yokohama 226-8503 (Japan)

    2015-08-21

    The converse piezoelectric responses of (111)- and (001)-epitaxial tetragonal Pb(Zr{sub 0.35}Ti{sub 0.65})O{sub 3} [PZT] films were compared to investigate the orientation dependence of the substrate clamping effect. Synchrotron X-ray diffraction (XRD) and piezoelectric force microscopy revealed that the as-grown (111)-PZT film has a polydomain structure with normal twin boundaries that are changed by the poling process to inclined boundaries, as predicted by Romanov et al. [Phys. Status Solidi A 172, 225 (1999)]. Time-resolved synchrotron XRD under bias voltage showed the negligible impact of substrate clamping on the piezoelectric response in the (111)-PZT film, unlike the case for (001)-PZT film. The origin of the negligible clamping effect in the (111)-PZT film is discussed from the viewpoint of the elastic properties and the compensation of lattice distortion between neighboring domains.

  6. Processing of Lead Zirconate Titanate-graphite 3-3 Piezocomposites

    Directory of Open Access Journals (Sweden)

    B. Praveenkumar

    2007-01-01

    Full Text Available The lead zirconate titanate (PZT-graphite piezocomposites have potential for higherpiezoelectric sensitivity, lower acoustic impedance, higher piezoelectric voltage constants, higherelectromechanical coupling coefficient, and higher hydrostatic coefficients as compared to densePZT materials. In addition, the properties of piezocomposites can be tailored for various weightpercentage of graphite powder. To study the phenomena, PZT-graphite 3-3 composites wereprepared by mixing calcined PZT and commercially available graphite powder. The mixed powderwas compacted, sintered, and poled by corona poling technique. Scanning electron microstructureswere recorded to study the effect of graphite on processing of 3-3 piezocomposites. The polarisingbehaviour, piezoelectric and dielectric properties of PZT-graphite composites were studied.

  7. Characteristics of magnetic force control device with magnetostrictive and piezoelectric laminate composite

    Science.gov (United States)

    Ueno, Toshiyuki; Qiu, Jinhao; Tani, Junji

    2003-08-01

    A magnetic force control device with laminate composite of giant magnetostrictive material (GMM) and piezo-electric material (PZT) is proposed. This magnetic force control is based on inverse magnetostrictive effect of a magnetic material, whereby the variation of stress applied on the material is converted to that of magnetic force via magnetic circuits. For the purpose of realizing the method in practical applications, disks of GMM and PZT are laminated to control the stress of GMM by electric field on PZT. Due to the capacitive properties of PZT, the device requires little electric energy hence generates no heat to maintain constant force. Furthermore compared with conventional electromagnetics, the device can be fabricated easily and in small size to be suitable for microactuators. This paper presents the principle of the magnetic force control by the lamination of GMM and PZT and investigates the static and dynamic characteristics of several devices to demonstrate their capabilities of the magnetic force control.

  8. Defect enhanced optic and electro-optic properties of lead zirconate titanate thin films

    Directory of Open Access Journals (Sweden)

    M. M. Zhu

    2011-12-01

    Full Text Available Pb(Zr1-xTixO3 (PZT thin films near phase morphotropic phase boundary were deposited on (Pb0.86La0.14TiO3-coated glass by radio frequency sputtering. A retrieved analysis shows that the lattice parameters of the as-grown PZT thin films were similar to that of monoclinic PZT structure. Moreover, the PZT thin films possessed refractive index as high as 2.504 in TE model and 2.431 in TM model. The as-grown PZT thin film had one strong absorption peak at 632.6 nm, which attributed to lead deficiency by quantitative XPS analysis. From the attractive properties achieved, electro-optic and photovoltaic characteristic of the films were carried out.

  9. Dielectric and pyroelectric properties of lead zirconate titanate/polyurethane composites

    Science.gov (United States)

    Lam, K. S.; Wong, Y. W.; Tai, L. S.; Poon, Y. M.; Shin, F. G.

    2004-10-01

    0-3 composite ranging between 0 and 3, of ferroelectric ceramic lead zirconate titanate (PZT) and thermoplastic elastomer polyurethane (PU) were fabricated. The pyroelectric and dielectric properties of the hot-pressed thin film samples of various PZT volume fractions were measured. The experimental dielectric permittivities and losses agreed reasonably well with the Bruggeman model. The room temperature pyroelectric coefficients of the composites were found to increase linearly with PZT volume fraction and substantially larger than expected. For example, for a composite with 30% PZT, its pyroelectric coefficient is about 90μC/m2K at room temperature, which is more than tenfold of a PZT/PVDF composite of the same ceramic volume fraction. We propose a model in which the electrical conductivity of the composite system is taken into consideration to explain the linear relationship and the extraordinarily large pyroelectric coefficients obtained.

  10. Numerical study on the mechanism of active interfacial debonding detection for rectangular CFSTs based on wavelet packet analysis with piezoceramics

    Science.gov (United States)

    Xu, Bin; Chen, Hongbing; Xia, Song

    2017-03-01

    In recent years, Piezoelectric Lead Zirconate Titanate (PZT) based active interfacial debonding defect detection approach for concrete-filled steel tubular (CFST) columns has been proposed and validated experimentally. In order to investigate the mechanism of the PZT based interfacial debonding detection approach, a multi-physics coupling finite element model (FEM) composed of surface-mounted PZT actuator, embedded PZT sensor and a rectangular CFST column is constructed to numerically simulate the stress wave propagation induced by the surface-mounted PZT actuator under different excitation signals with different frequency and amplitude. The measurements of the embedded PZT sensor in concrete core of the CFST columns with different interfacial debonding defect lengths and depths are determined numerically with transient dynamic analysis. The linearity between the PZT response and the input amplitude, the effect of different frequency and measurement distance are discussed and the stress wave fields of CFST members without and with interface debonding defects are compared. Then, the response of the embedded PZT in concrete core is analyzed with wavelet packet analysis. The root mean square deviation (RMSD) of wavelet packet energy spectrum of the PZT measurement is employed as an evaluation index for the interfacial debonding detection. The results showed that the defined index under continuous sinusoidal and sweep frequency signals changes with the interfacial defects length and depth and is capable of effectively identifying the interfacial debonding defect between the concrete core and the steel tubular. Moreover, the index under sweep frequency signal is more sensitive to the interfacial debonding. The simulation results indicate that the interfacial debonding defect leads to the changes in the propagation path, travel time and the magnitude of stress waves. The simulation results meet the findings from the previous experimental study by the authors and help

  11. Band bending at copper and gold interfaces with ferroelectric Pb(Zr,Ti)O3 investigated by photoelectron spectroscopy

    Science.gov (United States)

    Apostol, Nicoleta G.; Ştoflea, Laura E.; Tănase, Liviu C.; Bucur, Ioana Cristina; Chirilă, Cristina; Negrea, Raluca F.; Teodorescu, Cristian M.

    2015-11-01

    Interfaces formed by gold and copper on single crystal layers of (0 0 1) PbZr0.2Ti0.8O3 (PZT) produced by pulsed laser deposition and exhibiting outwards polarization are analyzed by X-ray photoelectron spectroscopy. The stoichiometry of the layers reproduces reasonably that of the PZT target. The band bending occurring at the interface between PZT and the metals is investigated by analyzing the core level shifts as function on the metal deposition. It is found that for Au/PZT(0 0 1) the gold layer is not continuous and the observed band bendings can be attributed to a Schottky mechanism, whereas for Cu/PZT(0 0 1) the copper layer is continuous; in this latter case, the observed band bendings towards higher energies (lower binding energies) can be attributed to a concomitant bending due to the Schottky effect together with the disappearance of the initial bending due to the outwards polarization of the samples. Metal Pb is observed to segregate only in the case of Cu/PZT(0 0 1), therefore the surface self-reduction might also be connected to the presence of a metal with lower work function, which for larger coverage forms a continuous metal layer, able to provide electrons to the surface. High resolution transmission electron spectroscopy yielded the disappearance of the tetragonal distortion in the case of Cu/PZT(0 0 1), in line with the assumption of disappearance of the polarization-induced band bending.

  12. Polycarbonate based three-phase nanocomposite dielectrics

    Science.gov (United States)

    Sain, P. K.; Goyal, R. K.; Prasad, Y. V. S. S.; Bhargava, A. K.

    2016-08-01

    Three-phase polycarbonate (PC) matrix nanocomposites are prepared using the solution method. One of the nanocomposite fillers is dielectric and the other is conducting. Lead zirconate titanate (PZT) is used as the dielectric filler. The conducting fillers, nano-Cu and multi-walled carbon nanotubes (MWCNTs), are used to make two different nanocomposites, MWCNT-PZT-PC and Cu-PZT-PC. The prepared nanocomposites are characterized using density measurement, x-ray diffractometry, scanning electron microscopy, energy dispersive x-ray spectroscopy, and differential scanning calorimetry. Percolation is absent in both three-phase nanocomposites within the study’s concentration window of conducting fillers. The dielectric properties of the nanocomposites are evaluated using a precision impedance analyser. The dielectric constant of the Cu-PZT-PC nanocomposite increases to 14 (a dissipation factor of 0.17), whereas in the case of the MWCNT-PZT-PC nanocomposite it increases to 8.5 (a dissipation factor of 0.002). The melting point of both nanocomposites decreases with respect to the control PC. The frequency (1 kHz to 1 MHz) and temperature (room temperature to 200 °C) dependence of the dielectric constant and dissipation factor are examined. For the Cu-PZT-PC nanocomposites, the dielectric constant decreases with increasing frequency, whereas in the case of the MWCNT-PZT-PC nanocomposites the dielectric constant is almost constant. The dielectric constant and dissipation factor exhibit a slight temperature dependence.

  13. Unveiling the Role of CNTs on the Phase Formation of 1D Ferroelectrics

    KAUST Repository

    Mahajan, Amit

    2015-05-21

    Carbon nanotubes (CNTs) have the potential to act as templates or bottom electrodes for three dimension (3D) capacitor arrays, which utilise one dimension (1D) ferroelectric nanostructures to increase memory size and density. However, growing a ferroelectric on the surface of CNTs is non-trivial. Here, we demonstrate that multi-walled (MW) CNTs decrease the time and temperature for formation of lead zirconium titanate Pb(Zr1-xTix)O3 (PZT) by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs/PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNT/PZT synthesised at 500 ºC for 1 h was proved. Although further work is required to prove the concept of 3D capacitor arrays, our result suggests that it is feasible to utilise MWCNTs as templates/electrodes for the formation of 1D PZT nano ferroelectrics.

  14. Remarkable Strontium B-Site Occupancy in FerroelectricPb(Zr1-xTix)O3 Solid Solutions Doped with Cryolite-Type StrontiumNiobate

    Energy Technology Data Exchange (ETDEWEB)

    Feltz, A.; Schmidt-Winkel, P.; Schossman, M.; Booth, C.H.; Albering, J.

    2007-04-26

    New high-performance ferroelectric materials based on Pb(Zr{sub 1-x}Ti{sub x})O{sub 3} (PZT) that are doped with cryolite-type strontium niobate (SNO, Sr{sub 4}(Sr{sub 2-2y/3}Nb{sub 2+2y/3})O{sub 11+y}V{sub 0,1-y} with 0 {le} y {le} 1), hence denoted PZT:SNO, and their microscopic structure are described. The combination of exceptional piezoelectric properties, i.e. a piezoelectric strain constant of d{sub 33} {approx} 760 pm/V, with excellent stability and degradation resistance makes ferroelectric PZT:SNO solid solutions very attractive for use in novel and innovative piezoelectric actuator and transducer applications. Extended X-ray absorption fine-structure (EXAFS) analyses of PZT:SNO samples revealed that {approx}10 % of the Sr cations occupy the nominal B-sites of the perovskite-type PZT host lattice. This result was supported by EXAFS analyses of both a canonical SrTiO{sub 3} perovskite and two SNO model and reference compounds. Fit models that do not account for Sr cations on B-sites were ruled out. A clear Sr-Pb peak in Fourier transformed EXAFS data visually confirmed this structural model. The generation of temporary oxygen vacancies and the intricate defect chemistry induced by SNO-doping of PZT are crucial for the exceptional materials properties exhibited by PZT:SNO materials.

  15. Electrical properties of (0 0 1)-textured Pb(Zr,Ti)O 3 thin films with different BaPbO 3 thicknesses

    Science.gov (United States)

    Liang, Chun-Sheng; Wu, Jenn-Ming

    2006-05-01

    The microstructure and electrical properties of highly (0 0 1)-textured lead zirconate titanate (PZT) thin films deposited on BaPbO 3 (BPO) at 475 °C by RF-magnetron sputtering were studied. Twenty-three, 65, and 136 nm-thick BPOs were adopted in this study. The dielectric constant is approximately 433 for Pt/PZT/BPO (23 nm), 443 for Pt/PZT/BPO (65 nm), and 466 for Pt/PZT/BPO (136 nm). The remanant polarization values in these three capacitors are 13.5, 14.9, and 10.9 μC/cm 2, and the coercive field values are 76.6, 71.2, and 54.5 kV/cm, respectively. The fatigue endurance of PZT films decreases with the thickness of BPO. The thickness of BPO layer not only influences the crystallinity of PZT films, but also the a-domain populations in PZT films. The variation of resultant electrical properties is attributed partly to the improvement of crystallinity, and partly to the population of a-domain. The effect of the former is remarkable when the BPO is thin while the latter is dominant when the BPO is thick.

  16. Effect of thickness on the stress and magnetoelectric coupling in bilayered Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3}-CoFe{sub 2}O{sub 4} films

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jing, E-mail: wang-jing@nuaa.edu.cn, E-mail: cwnan@tsinghua.edu.cn [State Key Laboratory of Mechanics and Control of Mechanical Structures, College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); Li, Zheng; Wang, Jianjun; Nan, Cewen, E-mail: wang-jing@nuaa.edu.cn, E-mail: cwnan@tsinghua.edu.cn [School of Materials Science and Engineering, State Key Lab of New Ceramics and Fine Processing, Tsinghua University, Beijing 100084 (China); He, Hongcai [State Key Lab of Electronic Thin Films and Integrated Devices, School of Microelectronics and Solid-State Electronics, University of Electronic Science and Technology of China, Chengdu, Sichuan 610054 (China)

    2015-01-28

    Magnetoelectric bilayered Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3}-CoFe{sub 2}O{sub 4}(PZT-CFO) films with different PZT thicknesses were grown on (111)Pt/Ti/SiO{sub 2}/Si substrates using chemical solution spin-coating. Structural characterization by X-ray diffraction and electron microscopy shows pure phases and well-defined interfaces between the PZT and CFO films. The CFO-PZT-substrate structure effectively alleviates the substrate clamping effect for the CFO layer, showing appreciable magnetoelectric responses in the composite films. Both the direct magnetoelectric effect and the magnetic field-induced Raman shifts in the A{sub 1}(TO{sub 1}) soft mode of PZT demonstrate the magnetic-mechanical-electric coupling in the films. The results also indicate that with a constant CFO layer thickness, the thickness of the PZT layer plays an important role in the stress relaxation and strong magnetoelectric coupling. The coupling could be further enhanced by increasing the CFO thickness, optimizing the volume (thickness) fraction of the PZT thickness, and releasing the clamping effect from the substrate.

  17. A Resistivity Gradient Piezoelectric FGM Actuator

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A resistivity gradient actuator based on lead zirconate titanate ceramics was successfully developed and the bending deflections up to 140 μm were obtained. The actuator material was a matrix of PZT ceramic into which smooth gradient of piezoelectric activity was introduced. The application of an electric field then causes the actuator to bend due to differential strains induced by the piezoelectric effect. The resistivity gradient of the actuator was achieved by doping PZT with suitable donor and acceptor dopants. PZT powder was modified and synthesized by using two stage powder fabrication method. The actuator was fabricated by uniaxial pressing followed by isostatic pressing with two layers of different resistivities.

  18. Dynamic nanocrystal response and high temperature growth of carbon nanotube-ferroelectric hybrid nanostructure

    Science.gov (United States)

    Kumar, Ashok; Scott, J. F.; Katiyar, R. S.

    2013-12-01

    A long standing problem related to the capping of carbon nanotubes (CNT) by inorganic materials at high temperature has been solved. In situ dynamic response of Pb(Zr0.52Ti0.48)O3 (PZT) nanocrystals attached to the wings of the outer surface of PZT/CNT hybrid-nanostructure has been demonstrated under a constant-energy high-resolution transmission electron microscopy (HRTEM) e-beam. PZT nanocrystals revealed that the crystal orientations, positions, faces, and hopping states change with time. HRTEM study has been performed to investigate the microstructure of hybrid nanostructures and nanosize polycrystal trapped across the wings. Raman spectroscopy was utilized to investigate the local structures, defects, crystal qualities and temperature dependent growth and degradation of hybrid nanostructures. Raman spectra indicate that MWCNT and PZT/MWCNT/n-Si possess good quality of CNT before and after PZT deposition until 650 °C. The monoclinic Cc/Cm phase of PZT which is optimum in piezoelectric properties was prominent in the hybrid structure and should be useful for device applications. An unusual hexagonal faceting oscillation of the nano-crystal perimeter on a 10-30 s period is also observed.A long standing problem related to the capping of carbon nanotubes (CNT) by inorganic materials at high temperature has been solved. In situ dynamic response of Pb(Zr0.52Ti0.48)O3 (PZT) nanocrystals attached to the wings of the outer surface of PZT/CNT hybrid-nanostructure has been demonstrated under a constant-energy high-resolution transmission electron microscopy (HRTEM) e-beam. PZT nanocrystals revealed that the crystal orientations, positions, faces, and hopping states change with time. HRTEM study has been performed to investigate the microstructure of hybrid nanostructures and nanosize polycrystal trapped across the wings. Raman spectroscopy was utilized to investigate the local structures, defects, crystal qualities and temperature dependent growth and degradation of

  19. Modeling of Magnetoelectric Interaction in Magnetostrictive-Piezoelectric Composites

    Directory of Open Access Journals (Sweden)

    M. I. Bichurin

    2012-01-01

    Full Text Available The paper dwells on the theoretical modeling of magnetoelectric (ME effect in layered and bulk composites based on magnetostrictive and piezoelectric materials. Our analysis rests on the simultaneous solution of elastodynamic or elastostatic and electro/magnetostatic equations. The expressions for ME coefficients as the functions of material parameters and volume fractions of components are obtained. Longitudinal, transverse, and in-plane cases are considered. The use of the offered model has allowed to present the ME effect in ferrite cobalt-barium titanate, ferrite cobalt-PZT, ferrite nickel-PZT, and lanthanum strontium manganite-PZT composites adequately.

  20. Voltage generation of piezoelectric cantilevers by laser heating.

    Science.gov (United States)

    Hsieh, Chun-Yi; Liu, Wei-Hung; Chen, Yang-Fang; Shih, Wan Y; Gao, Xiaotong; Shih, Wei-Heng

    2012-11-15

    Converting ambient thermal energy into electricity is of great interest in harvesting energy from the environment. Piezoelectric cantilevers have previously been shown to be an effective biosensor and a tool for elasticity mapping. Here we show that a single piezoelectric (lead-zirconate titanate (PZT)) layer cantilever can be used to convert heat to electricity through pyroelectric effect. Furthermore, piezoelectric-metal (PZT-Ti) bi-layer cantilever showed an enhanced induced voltage over the single PZT layer alone due to the additional piezoelectric effect. This type of device can be a way for converting heat energy into electricity.

  1. Characterization and microstructure of porous lead zirconate titanate ceramics

    Indian Academy of Sciences (India)

    B Praveenkumar; H H Kumar; D K Kharat

    2005-08-01

    Porous lead zirconate titanate (PZT) ceramics are widely used because of their low acoustic impedance, high figure of merit and high hydrostatic sensitivity. In the present work, porous PZT ceramics were fabricated by incorporating polyethylene oxide (PEO) as pore-forming agent. Both PZT powder and PEO were mixed with a binder at different ratios and compaction was carried out. The samples were slowly heated to remove the pore-forming agent and binder without cracks, followed by controlled sintering and electrode forming. Samples were poled using corona poling technique. The ferroelectric properties and microstructure of the prepared ceramics were characterized. The correlation of porosity with microstructure and ferroelectric properties were discussed.

  2. Laser frequency modulator for modulating a laser cavity

    Science.gov (United States)

    Erbert, Gaylen V.

    1992-01-01

    The present invention relates to a laser frequency modulator for modulating a laser cavity. It is known in the prior art to utilize a PZT (piezoelectric transducer) element in combination with a mirror to change the cavity length of a laser cavity (which changes the laser frequency). Using a PZT element to drive the mirror directly is adequate at frequencies below 10 kHz. However, in high frequency applications (100 kHz and higher) PZT elements alone do not provide a sufficient change in the cavity length. The present invention utilizes an ultrasonic concentrator with a PZT element and mirror to provide modulation of the laser cavity. With an ultrasonic concentrator, the mirror element at the end of a laser cavity can move at larger amplitudes and higher frequencies.

  3. Piezoelectric Sensor to Measure Soft and Hard Stiffness with High Sensitivity for Ultrasonic Transducers.

    Science.gov (United States)

    Li, Yan-Rui; Su, Chih-Chung; Lin, Wen-Jin; Chang, Shuo-Hung

    2015-06-11

    During dental sinus lift surgery, it is important to monitor the thickness of the remaining maxilla to avoid perforating the sinus membrane. Therefore, a sensor should be integrated into ultrasonic dental tools to prevent undesirable damage. This paper presents a piezoelectric (PZT) sensor installed in an ultrasonic transducer to measure the stiffness of high and low materials. Four design types using three PZT ring materials and a split PZT for actuator and sensor ring materials were studied. Three sensor locations were also examined. The voltage signals of the sensor and the displacement of the actuator were analyzed to distinguish the low and high stiffness. Using sensor type T1 made of the PZT-1 material and the front location A1 provided a high sensitivity of 2.47 Vm/kN. The experimental results demonstrated that our design can measure soft and hard stiffness.

  4. Magnetoelectric Interactions in Lead-Based and Lead-Free Composites

    Directory of Open Access Journals (Sweden)

    Shashank Priya

    2011-04-01

    Full Text Available Magnetoelectric (ME composites that simultaneously exhibit ferroelectricity and ferromagnetism have recently gained significant attention as evident by the increasing number of publications. These research activities are direct results of the fact that multiferroic magnetoelectrics offer significant technological promise for multiple devices. Appropriate choice of phases with co-firing capability, magnetostriction and piezoelectric coefficient, such as Ni-PZT and NZFO-PZT, has resulted in fabrication of prototype components that promise transition. In this manuscript, we report the properties of Ni-PZT and NZFO-PZT composites in terms of ME voltage coefficients as a function of frequency and magnetic DC bias. In order to overcome the problem of toxicity of lead, we have conducted experiments with Pb-free piezoelectric compositions. Results are presented on the magnetoelectric performance of Ni-NKN, Ni-NBTBT and NZFO-NKN, NZFO-NBTBT systems illustrating their importance as an environmentally friendly alternative.

  5. Fabrication and characterization of cell culture microdevice for nanomechanical stimulation of living cells

    Science.gov (United States)

    Shibata, Takayuki; Umegaki, Genki; Ishihara, Yoshitaka; Nagai, Moeto; Kawashima, Takahiro

    2014-02-01

    In order to elucidate the effects of nanomechanical stimulation on the regulation of cellular functions, we have been developing a cell culture microdevice integrated with piezoelectric thin film actuators. In this paper, we propose a new geometric configuration of the device to allow cell culture on a relatively flat surface and in an open space. An improved fabrication process for PZT actuators overcame a serious problem that sometimes occurred in the previous process; photoresist patterned on PZT film cannot be completely removed due to its degradation in a dry etching process. Then we demonstrate the driving performance of a fabricated prototype microdevice. Moreover, individual cells can be arranged precisely at the desired positions of the PZT actuators by a positive dielectrophoretic force at frequencies above 100 kHz with an application of an AC voltage of 20 Vpp. The trapping rate was dramatically improved up to 90% by using microchannel to efficiently supply cells onto the surface of the PZT actuator.

  6. Real-time one-point out-of-plane displacement measurement system using electronic speckle pattern interferometry

    Science.gov (United States)

    Xiong, Chen; Hu, Wenxin; Zhang, Ming; Miao, Hong

    2016-12-01

    We propose an electronic speckle pattern interferometry-based measurement method in which a hardware device in the reference arm is used to track the out-of-plane displacement in the objective arm. We developed a real-time one-point out-of-plane displacement measurement system, which uses a Michelson interferometer, a lead zirconate titanate (PZT) device, a charge-coupled device camera, and a tracking control system. The system works by checking the movement of carrier fringes, and the PZT is used to track the displacement. We also developed an efficient tracking algorithm based on direction judgment and correlation computation to determine whether the PZT is activated and the distance that the PZT is ordered to move. Our experimental results demonstrate the effectiveness of the system, and finally, we discuss the detailed mechanism of the system.

  7. Experimental and Theoretical Investigations of the Impact Localization of a Passive Smart Composite Plate Fabricated Using Piezoelectric Materials

    Directory of Open Access Journals (Sweden)

    M. M. S. Dezfouli

    2013-01-01

    Full Text Available Two passive smart composite plates are fabricated using one and two PZT patches that are cheaper than the PZT wafer. The composite plate is fabricated in low temperature through the hand lay-up method to avoid PZT patch decoupling and wire spoiling. The locus of the impact point is identified using the output voltage to identify the impact location using one sensor. The output voltages of the sensors are analyzed to identify the impact location using two sensors. The locations of the impacts are determined based on the crossing points of two circles and the origin of an intended Cartesian coordinate system that is concentric with one of the sensors. This study proposes the impact location identification of the passive smart composite using the low-cost PZT patch PIC155 instead of common embedded materials (wafer and element piezoelectric.

  8. Manipulation of charge transfer and transport in plasmonic-ferroelectric hybrids for photoelectrochemical applications

    Science.gov (United States)

    Wang, Zhijie; Cao, Dawei; Wen, Liaoyong; Xu, Rui; Obergfell, Manuel; Mi, Yan; Zhan, Zhibing; Nasori, Nasori; Demsar, Jure; Lei, Yong

    2016-01-01

    Utilizing plasmonic nanostructures for efficient and flexible conversion of solar energy into electricity or fuel presents a new paradigm in photovoltaics and photoelectrochemistry research. In a conventional photoelectrochemical cell, consisting of a plasmonic structure in contact with a semiconductor, the type of photoelectrochemical reaction is determined by the band bending at the semiconductor/electrolyte interface. The nature of the reaction is thus hard to tune. Here instead of using a semiconductor, we employed a ferroelectric material, Pb(Zr,Ti)O3 (PZT). By depositing gold nanoparticle arrays and PZT films on ITO substrates, and studying the photocurrent as well as the femtosecond transient absorbance in different configurations, we demonstrate an effective charge transfer between the nanoparticle array and PZT. Most importantly, we show that the photocurrent can be tuned by nearly an order of magnitude when changing the ferroelectric polarization in PZT, demonstrating a versatile and tunable system for energy harvesting.

  9. Piezoelectric Sensor to Measure Soft and Hard Stiffness with High Sensitivity for Ultrasonic Transducers

    Directory of Open Access Journals (Sweden)

    Yan-Rui Li

    2015-06-01

    Full Text Available During dental sinus lift surgery, it is important to monitor the thickness of the remaining maxilla to avoid perforating the sinus membrane. Therefore, a sensor should be integrated into ultrasonic dental tools to prevent undesirable damage. This paper presents a piezoelectric (PZT sensor installed in an ultrasonic transducer to measure the stiffness of high and low materials. Four design types using three PZT ring materials and a split PZT for actuator and sensor ring materials were studied. Three sensor locations were also examined. The voltage signals of the sensor and the displacement of the actuator were analyzed to distinguish the low and high stiffness. Using sensor type T1 made of the PZT-1 material and the front location A1 provided a high sensitivity of 2.47 Vm/kN. The experimental results demonstrated that our design can measure soft and hard stiffness.

  10. High Reliability Cryogenic Piezoelectric Valve Actuator Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Piezoelectric actuators constructed with the "smart material" PZT offer many potential advantages for use in NASA cryo-valve missions relative to conventional...

  11. STRUCTURAL STUDY OF PZT/YBCO BY TRIPLE—AXES DIFFRACTION

    Institute of Scientific and Technical Information of China (English)

    Z.H.MAI; A.I.ZHU; 等

    1999-01-01

    The structures of Pb(ZrxTi1-x)O3/YBCO heterostructure with different thickness of PZT sublayer were investigated.The lattice parameter,c of YBCO layer is obtained to be c=11.686±0.001A.being of 0.2% larger than that of the bulk one.The lattice parameter,c of PZT layer is c=4.116±0.001A,indicating that the composition of the sample is Pb(Zr0.48Ti0.52)O3.The misorientations of YBCO/PZT sublayers were observed in the samples B and D.The effect of the crystalline quality of the STO substrate o the quality of the YBCO and PZT epitaxial fllms was discussed.

  12. Compositional Effects on Electromechanical Degradation of RAINBOW Actuators

    Science.gov (United States)

    Dausch, David E.; Wise, Stephanie A.

    1998-01-01

    The effect of ceramic composition on the electromechanical displacement degradation of RAINBOW (Reduced and Internally Biased Oxide Wafer) actuators was investigated. RAINBOWs were fabricated from commercially available PZT-5H and PZT-5A piezoelectric disks as well as from tape cast PLZT piezoelectric 7/65/35 and electrostrictive 9/65/35 compositions. Displacement properties were measured at low electric fields (10 to 13 kV/cm) under loads of 0 to 500 g, and displacement degradation as a function of time was observed over 107 cycles. The PZT-5A and PLZT 9/65/35 compositions exhibited minimal decrease in displacement when load was applied. Furthermore, these compositions retained approximately 65 percent of their initial displacement after 10(exp 7) cycles under a load of 300 g. PZT-5H and PLZT 7/65/35 degraded completely under these conditions.

  13. Ultrasonic Motors

    Science.gov (United States)

    2003-06-01

    and T. Higuchi, "Cylindrical Micro Ultrasonic Motor Utilizing Bulk Lead Zirconate Titanate (PZT)," Japanese Journal of Applied Physics Part 1-Regular Papers Short Notes & Review Papers, vol. 38, pp. 3347-3350, 1999.

  14. Fabrication of Lead Zirconate Titanate Powder Using Ultrasonic Ball Milling Technique

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this research, the ultrasonic ball milling technique has been used to fabricate lead zirconate titanate (PZT) ceramics.PZT with the composition nearly the morphotropic phase boundary (MPB): Pb(Zr0.52 Ti0.48 )O3 was studied. The effect of milling time on phase formation of sample powder was examined by X-ray diffraction technique (XRD). Moreover, the physical, dielectric, piezoelectric properties and microstructure of PZT ceramics were investigated. The present results reveal that the ultrasonic ball milling technique results the homogeneous and small size of PZT powder. Furthermore, there is a significantly change occurs in the size of the particles with the short time of milling process.

  15. Magnetic field-dependent polarization of (111)-oriented PZT–Co ferrite nanobilayer: Effect of Co ferrite composition

    Energy Technology Data Exchange (ETDEWEB)

    Khodaei, M. [Advanced Magnetic Materials Research Center, School of Metallurgy and Materials, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Faculty of Materials Science and Engineering, K. N. Toosi University of Technology, Tehran (Iran, Islamic Republic of); Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang 790-784 (Korea, Republic of); Seyyed Ebrahimi, S.A., E-mail: saseyyed@ut.ac.ir [Advanced Magnetic Materials Research Center, School of Metallurgy and Materials, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Jun Park, Yong [Pohang Accelerator Laboratory, Pohang University of Science and Technology (POSTECH), Pohang 790-784 (Korea, Republic of); Son, Junwoo; Baik, Sunggi [Department of Materials Science and Engineering, Pohang University of Science and Technology (POSTECH), Pohang 790-784 (Korea, Republic of)

    2015-05-15

    The perfect (111)-oriented PZT/CFO (CFO=CoFe{sub 2}O{sub 4}, Co{sub 0.8}Fe{sub 2.2}O{sub 4} and Co{sub 0.6}Mn{sub 0.2}Fe{sub 2.2}O{sub 4}) bilayer multiferroic thin films were grown on Pt(111)/Si substrate at 600 °C using pulsed laser deposition technique. The precision X-ray diffraction analysis (avoiding the shift of peak due to the sample misalignment) revealed that the CFO films on Pt(111)/Si substrate were under an out-of-plane contraction and deposition of PZT top layer led to more increase in the out-of-plane contraction, i.e. increase in the residual stresses. The PZT and CFO layers have significant effects on magnetic and ferroelectric properties of PZT/CFO bilayer films, respectively, leading to an enhanced in-plane magnetic anisotropy as well as increased and asymmetric polarization. The effect of composition of CFO layer on magnetic field-dependent polarization of PZT/CFO bilayer films was investigated by applying the magnetic field during P-E measurement. The polarization of PZT films were increased by applying the magnetic field as a result of strain transferred from magnetostrictive CFO underlayer. This increase in polarization for PZT/Co{sub 0.6}Mn{sub 0.2}Fe{sub 2.2}O{sub 4} was higher than that for PZT/Co{sub 0.8}Fe{sub 2.2}O{sub 4} and both of them were significantly higher than that for PZT/CoFe{sub 2}O{sub 4} bilayer film, which was discussed based on their magnetostriction properties. - Highlights: • The effect of composition of CFO on P–E characteristics of PZT/CFO films was investigated. • The polarization of PZT films were increased by applying the magnetic field. • The increasing polarization was a result of strain from magnetostrictive CFO underlayer.

  16. A Fully Integrated Materials Framework for Enabling the Wireless Detection of Micro-defects in Aging and Battle-worn Structures (Year 1)

    Science.gov (United States)

    2011-04-01

    the sputtered PZT films on both substrates were polycrystalline and had the perovskite structure, as shown in figures 10 and 11. Furthermore, the...played a crucial role in the PZT perovskite phase formation, where an excess decreased the quality of the crystal formation, paving the way for...Our characterization system uses an Agilent 4156C Precision Semiconductor Parameter Analyzer as the current source and voltage meter. An Agilent

  17. Smart patch integration development of compression connector structural health monitoring in overhead transmission lines

    Science.gov (United States)

    Wang, Hong; Wang, Jy-An J.; Ren, Fei; Chan, John

    2016-04-01

    Integration of smart patches into full-tension splice connectors in overhead power transmission lines was investigated. Lead zirconate titanate (PZT) -5A was used as a smart material and an aluminum beam was used as a host structure. Negative electrode termination was examined by using copper adhesive tape and direct bonding methods. Various commercial adhesives were studied for PZT integration onto the host structure. Aluminum beam specimens with integrated PZT smart patches were tested under thermal cycling at a temperature of 125°C, which is the higher-end temperature experienced by in-service aluminum conductor steel-reinforced cables. Electromechanical impedance (EMI) measurements were conducted at room temperature, and the root mean square deviation (RMSD) of the conductance signals was used to analyze the EMI data. It has been shown that the negative electrode method has an important effect on the performance of the integrated PZT. The PZT displayed more susceptibility to cracking when copper tape was used than when direct bonding was used. The reliability of PZT in direct bonding depended on the adhesives used in bonding layers. Although a hard alumina-based adhesive can lead to cracking of the PZT, a high-temperature epoxy with adequate flexibility, such as Duralco 4538D, can provide the desired performance under target thermal cycling conditions. The RMSD parameter can characterize conductance signatures effectively. It also was demonstrated that RMSD can be used to quantify the fatigue of the PZT integration system, although RMSD is used primarily as a damage index in monitoring structural health.

  18. Integration of epitaxial Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3} films on GaN/AlGaN/GaN/Si(111) substrates using rutile TiO{sub 2} buffer layers

    Energy Technology Data Exchange (ETDEWEB)

    Elibol, K. [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands); Nguyen, M.D. [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands); SolMateS B.V., Drienerlolaan 5, Building 6, 7522NB Enschede (Netherlands); International Training Institute for Materials Science, Hanoi University of Science and Technology, No.1 Dai Co Viet road, Hanoi 10000 (Viet Nam); Hueting, R.J.E. [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands); Gravesteijn, D.J. [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands); NXP Semiconductors Research, High Tech Campus 46, 5656AE Eindhoven (Netherlands); Koster, G., E-mail: g.koster@utwente.nl [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands); Rijnders, G. [MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500AE Enschede (Netherlands)

    2015-09-30

    The integration of ferroelectric layers on gallium nitride (GaN) offers a great potential for various applications. Lead zirconate titanate (PZT), in particular Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3}, is an interesting candidate. For that a suitable buffer layer should be grown on GaN in order to prevent the reaction between PZT and GaN, and to obtain PZT with a preferred orientation and phase. Here, we study pulsed laser deposited (100) rutile titanium oxide (R-TiO{sub 2}) as a potential buffer layer candidate for ferroelectric PZT. For this purpose, the growth, morphology and the surface chemical composition of R-TiO{sub 2} films were analyzed by reflection high-energy electron diffraction, atomic force microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. We find optimally (100) oriented R-TiO{sub 2} growth on GaN (0002) using a 675 °C growth temperature and 2 Pa O{sub 2} deposition pressure as process conditions. More importantly, the R-TiO{sub 2} buffer layer grown on GaN/Si substrates prevents the unwanted formation of the PZT pyrochlore phase. Finally, the remnant polarization and coercive voltage of the PZT film on TiO{sub 2}/GaN/Si with an interdigitated-electrode structure were found to be 25.6 μC/cm{sup 2} and 8.1 V, respectively. - Highlights: • Epitaxial rutile TiO{sub 2} films were grown on GaN layer buffered Si substrate using pulsed laser deposition. • The rutile-TiO{sub 2} layer suppresses the formation of the pyrochlore phase in the epitaxial PZT film grown on GaN/Si. • An epitaxial PZT film on GaN/Si substrate with rutile TiO{sub 2} buffer layer exhibits good ferroelectric properties.

  19. Effect of dopants on ferroelectric and piezoelectric properties of lead zirconate titanate thin films on Si substrates

    NARCIS (Netherlands)

    Nguyen, Duc Minh; Trinh, Thong Q.; Dekkers, Jan M.; Houwman, Evert Pieter; Vu, Hung Ngoc; Rijnders, Augustinus J.H.M.

    2014-01-01

    Lead zirconate titanate Pb(Zr0.52Ti0.48)O3 (undoped PZT) and doped PZT thin films with thickness of about 500 nm were grown on Pt/Ti/SiO2/Si substrates by pulsed laser deposition (PLD). In this study, 1.0 mol% Nb-doping (at Zr/Ti site) as donor, 1.0 mol% Fe-doping (at Zr/Ti) as acceptor and 10 mol%

  20. Extrusion and properties of lead zirconate titanate piezoelectric ceramics

    DEFF Research Database (Denmark)

    Cai, S.; Millar, C.E.; Pedersen, L.

    1997-01-01

    The purpose of this work was to develop a procedure for fabricating electroceramic actuators with good piezoelectric properties. The preparation of lead zirconate titanate (PZT) piezoelectric ceramic rods and tubes by extrusion processing is described. The microstructure of extrudates was investi......The purpose of this work was to develop a procedure for fabricating electroceramic actuators with good piezoelectric properties. The preparation of lead zirconate titanate (PZT) piezoelectric ceramic rods and tubes by extrusion processing is described. The microstructure of extrudates...

  1. Active Vibration Suppression of a 3-DOF Flexible Parallel Manipulator Using Efficient Modal Control

    OpenAIRE

    Quan Zhang; Jiamei Jin; Jianhui Zhang; Chunsheng Zhao

    2014-01-01

    This paper addresses the dynamic modeling and efficient modal control of a planar parallel manipulator (PPM) with three flexible linkages actuated by linear ultrasonic motors (LUSM). To achieve active vibration control, multiple lead zirconate titanate (PZT) transducers are mounted on the flexible links as vibration sensors and actuators. Based on Lagrange’s equations, the dynamic model of the flexible links is derived with the dynamics of PZT actuators incorporated. Using the assumed mode me...

  2. Influence of Grain Structure and Doping on the Deformation and Fracture of Polycrystalline Silicon for MEMS/NEMS

    Science.gov (United States)

    2012-08-01

    Champaign Influence of Grain Structure and Doping on the Deformation and Fracture of Polycrystalline Silicon for MEMS/ NEMS AFOSR Grant # FA9550-09-1...Structure and Doping on the Deformation and Fracture of Polycrystalline Silicon for MEMS/ NEMS 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM...Behavior of PZT Films for MEMS  PZT thin films are used in MEMS devices, such as micro- sensors , actuators, and RF-MEMS  Always fabricated in

  3. Study of HV Dielectrics for High Frequency Operation in Linear and Nonlinear Transmission Lines (NLTLs) and Simulation and Development of Hybrid Nonlinear Lines for RF Generation

    Science.gov (United States)

    2016-01-27

    have better performance than BT-based dielectrics in this frequency range because of the PZT lower loss tangent. The reason is that PZT dielectric...during pulse formation the top of the reflected voltage pulse travels faster along the line than its bottom distorting the voltage step into a ramp... inductances due to component geometry or terminals limits the output frequency in NLTLs. As shown in Fig. 6, as expected the permittivity for all

  4. The Comparative Study of Vibration Control of Flexible Structure Using Smart Materials

    OpenAIRE

    Juntao Fei; Yunmei Fang; Chunyan Yan

    2010-01-01

    Considerable attention has been devoted to active vibration control using intelligent materials as PZT actuators. This paper presents results on active control schemes for vibration suppression of flexible steel cantilever beam with bonded piezoelectric actuators. The PZT patches are surface bonded near the fixed end of flexible steel cantilever beam. The dynamic model of the flexible steel cantilever beam is derived. Active vibration control methods: optimal PID control, strain rate feedback...

  5. A Review of Australian and New Zealand Investigations on Aeronautical Fatigue During the Period April 2009 to March 2011

    Science.gov (United States)

    2011-05-01

    threshold regime than steady-state CA data on a number of materials (two aluminium alloys, two titanium alloys and a superalloy ), especially those...diameter elements were incorporated with 10 mm diameter and 0.5 mm thick PZT disc transducers to experimentally evaluate the approach. Theoretical and...AMAP sensor and PZT elements were installed on an aluminium plate. In this case a small thick aluminium disc was bonded to the panel to produce a

  6. Research into an integrated intelligent structure- A new actuator combining piezoelectric ceramic and electrorheological fluid

    Science.gov (United States)

    Quanlu, Li

    2002-02-01

    The design, preparation, and application of high-performance piezoelectric ceramics, e.g., FD3-PZT and FD4-PZT, then preparation, performance measurement, and applications of composite electrorheological fluids have been studied, respectively. The integrated intelligent structure (i.e., a new actuator) combining the piezoelectric ceramic and the electrorheological fluids, and their applications have been investigated, and emphasis was given to the applications in acoustics and vibration control, etc. as may be noted.

  7. STUDY OF REACTION SEQUENCES FOR FORMATION OF SOLID ...

    African Journals Online (AJOL)

    31 déc. 2012 ... phase intermédiaire PbTiO3 et la formation de PZT à 800 °C. ... matériau céramique de type PZT de formule chimique: 0,48PbZrO3-0 .... (ATG) relative au mélange par un changement de perte visible équivalente à 3%.

  8. Smart patch integration development of compression connector structural health monitoring in overhead transmission lines

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hong [ORNL; Wang, Jy-An John [ORNL; Ren, Fei [ORNL; Chan, John [Electric Power Research Institute (EPRI)

    2016-01-01

    Integration of smart patches into full-tension splice connectors in overhead power transmission lines was investigated. Lead zirconate titanate (PZT) -5A was used as a smart material and an aluminum beam was used as a host structure. Negative electrode termination was examined by using copper adhesive tape and direct bonding methods. Various commercial adhesives were studied for PZT integration onto the host structure. Aluminum beam specimens with integrated PZT smart patches were tested under thermal cycling at a temperature of 125 C, which is the higher-end temperature experienced by in-service aluminum conductor steel-reinforced cables. Electromechanical impedance (EMI) measurements were conducted at room temperature, and the root mean square deviation (RMSD) of the conductance signals was used to analyze the EMI data. It has been shown that the negative electrode method has an important effect on the performance of the integrated PZT. The PZT displayed more susceptibility to cracking when copper tape was used than when direct bonding was used. The reliability of PZT in direct bonding depended on the adhesives used in bonding layers. Although a hard alumina based adhesive can lead to cracking of the PZT, a high-temperature epoxy with adequate flexibility, such as Duralco 4538D, can provide the desired performance under target thermal cycling conditions. The RMSD parameter can characterize conductance signatures effectively. It also was demonstrated that RMSD can be used to quantify the fatigue of the PZT integration system, although RMSD is used primarily as a damage index in monitoring structural health.

  9. Ultracold Fermions in the P-Orbital Band of an Optical Lattice

    Science.gov (United States)

    2015-07-27

    cooling and trapping of lithium atoms. Nd:YVO 4 etalon1 OC LD 808nm LD 808nm etalon2 PZT1 PZT2 OI M1 M2 M3 M4 PBS LBO ICPZT3 M7 M5 671nm M6 EOM HWP HWP...Haddad from the Colorado School of Mines which focussed on relativistic phe- nomena that can be studied with ultracold atoms in a honeycomb lattice

  10. Vertically Free-Standing Ordered Pb(Zr0.52Ti0.48)O3 Nanocup Arrays by Template-Assisted Ion Beam Etching

    Science.gov (United States)

    Zhang, Xiaoyan; Tang, Dan; Huang, Kangrong; Hu, Die; Zhang, Fengyuan; Gao, Xingsen; Lu, Xubing; Zhou, Guofu; Zhang, Zhang; Liu, Junming

    2016-04-01

    In this report, vertically free-standing lead zirconate titanate Pb(Zr0.52Ti0.48)O3 (PZT) nanocup arrays with good ordering and high density (1.3 × 1010 cm-2) were demonstrated. By a template-assisted ion beam etching (IBE) strategy, the PZT formed in the pore-through anodic aluminum oxide (AAO) membrane on the Pt/Si substrate was with a cup-like nanostructure. The mean diameter and height of the PZT nanocups (NCs) was about 80 and 100 nm, respectively, and the wall thickness of NCs was about 20 nm with a hole depth of about 80 nm. Uppermost, the nanocup structure with low aspect ratio realized vertically free-standing arrays when losing the mechanical support from templates, avoiding the collapse or bundling when compared to the typical nanotube arrays. X-ray diffraction (XRD) and Raman spectrum revealed that the as-prepared PZT NCs were in a perovskite phase. By the vertical piezoresponse force microscopy (VPFM) measurements, the vertically free-standing ordered ferroelectric PZT NCs showed well-defined ring-like piezoresponse phase and hysteresis loops, which indicated that the high-density PZT nanocup arrays could have potential applications in ultra-high non-volatile ferroelectric memories (NV-FRAM) or other nanoelectronic devices.

  11. Reversible Polarization Rotation in Epitaxial Ferroelectric Bilayers

    DEFF Research Database (Denmark)

    Liu, Guangqing; Zhang, Qi; Huang, Hsin-Hui

    2016-01-01

    Polarization rotation engineering is a promising path to giant dielectric and electromechanical responses in ferroelectric materials and devices. This work demonstrates robust and reversible in- to out-of-plane polarization rotation in ultrathin (nanoscale) epitaxial (001) tetragonal PbZr0.3Ti0.7O3...... (PZT-T)/rhombohedral PbZr0.55Ti0.45O3 (PZT-R) ferroelectric bilayers. An underlying 20 nm thick PZT-R layer reduces the symmetry in a 5 nm thick PZT-T layer by imposing an in-plane tensile strain while simultaneously decoupling the PZT-T layer from the substrate. This prevents clamping and facilitates...... large-scale polarization rotation switching (≈60 μC cm−2) and an effective d 33 response 500% (≈250 pm V−1) larger than the PZT-R layer alone. Furthermore, this enhancement is stable for more than 107 electrical switching cycles. These bilayers present a simple and highly controllable means to design...

  12. Dynamic nanocrystal response and high temperature growth of carbon nanotube-ferroelectric hybrid nanostructure.

    Science.gov (United States)

    Kumar, Ashok; Scott, J F; Katiyar, R S

    2014-01-21

    A long standing problem related to the capping of carbon nanotubes (CNT) by inorganic materials at high temperature has been solved. In situ dynamic response of Pb(Zr0.52Ti0.48)O3 (PZT) nanocrystals attached to the wings of the outer surface of PZT/CNT hybrid-nanostructure has been demonstrated under a constant-energy high-resolution transmission electron microscopy (HRTEM) e-beam. PZT nanocrystals revealed that the crystal orientations, positions, faces, and hopping states change with time. HRTEM study has been performed to investigate the microstructure of hybrid nanostructures and nanosize polycrystal trapped across the wings. Raman spectroscopy was utilized to investigate the local structures, defects, crystal qualities and temperature dependent growth and degradation of hybrid nanostructures. Raman spectra indicate that MWCNT and PZT/MWCNT/n-Si possess good quality of CNT before and after PZT deposition until 650 °C. The monoclinic Cc/Cm phase of PZT which is optimum in piezoelectric properties was prominent in the hybrid structure and should be useful for device applications. An unusual hexagonal faceting oscillation of the nano-crystal perimeter on a 10-30 s period is also observed.

  13. Pb(Ni1/3Sb2/3O3-PbZrTiO3 Ceramic Sensors for Underwater Transducer Application

    Directory of Open Access Journals (Sweden)

    C. M. Lonkar

    2012-07-01

    Full Text Available Cymbal is a class-V flextensional transducer that consists of thickness poled ceramic disc sandwiched between the two metal end caps which acts as a mechanical transformer. Cymbal transducers were fabricated using piezoceramic discs of compositions Pb0.988(Zr0.52Ti0.48 0.976Nb0.024O3 (PZT type 5A and Pb0.98La0.02 (NiSb0.05[(Zr0.52 Ti0.480.995]0.95O3 (PNS-PZT. Piezoelectric and hydrostatic constants for PNS-PZT composition were on higher side. End capswere made up of brass sheet having thickness 0.5 mm. Underwater testing of the polyurethane moulded cymbal hydrophones were carried out in acoustic tank and compared. The resonance frequency for both the hydrophones was 10.1 kHz. PNS-PZT hydrophone shows higher sensitivity (-183.2 dB re 1V/μPa compared to PZT type 5A (-191.2 dB re 1V/μPa at resonance frequency. Directivity pattern observed for PNS-PZT is omni-directional near resonance frequency.Defence Science Journal, 2012, 62(4, pp.269-273, DOI:http://dx.doi.org/10.14429/dsj.62.1718

  14. Incorporation of piezoelectric Pb(Zr,Ti)O3 fibers into ceramic/polymer composites

    Science.gov (United States)

    Safari, Ahmad; Janas, Victor; Jadidian, Bahram; French, Jonathan D.; Weitz, Gregory E.; Luke, John E.; Cass, Bud

    1996-05-01

    The processing of Pb(Zr,Ti)O3, or PZT, fiber and fiber/polymer composites for transducer applications is discussed. Green PZT fibers, 80 to 100 micrometers in diameter, were formed at Advanced Cerametrics, Inc., using the Viscous Suspension Spinning Process (VSSP). In this process, fine PZT powder is intimately mixed with polymer precursor by high shear mixing. The powder and precursor mixture is spun through a spinneret into a coagulation bath to form fibers. The fibers are washed, dried, and collected on a spool. Yarns containing between 10 and 500 individual fibers were collimated by applying a polymeric sizing to the yarns, and passing the yarns through sizing dies. Yarn bundle tightness and flexibility were controlled by the sizing chemistry. Continuous green yarns were cut to short lengths, or woven in different architectures to create composites with novel microstructures. The short yarns were fired to product PZT straight rods for `pick and place' piezoelectric composites. The woven structures were heat treated and backfilled with polymer to create composites with 1-3, 2-3, and 3-3 connectivity. After heat treatment, the diameter of the individual PZT fibers was 10 to 20 micrometers . Electromechanical characteristics of a number of composites were determined, and will be reported. The PZT VSSP fibers can be used to form fine-scale, large area piezoelectric fiber/polymer composites for use in hydrophones, transducers for medical ultrasonic imaging and non-destructive evaluation, and as sensors and actuators in vibration and noise control.

  15. High-performance energy harvester fabricated with aerosol deposited PMN-PT material

    Science.gov (United States)

    Chen, C. T.; Lin, S. C.; Lin, T. K.; Wu, W. J.

    2016-11-01

    This paper reports a high-performance piezoelectric energy harvester (EH) fabricated with xPb(Mg1/3Nb2/3)-(l-x)PbTiO3 (PMN-PT) by aerosol deposition method. The result indicates that PMN-PT based EH owns 1.8 times output power which is higher than traditional PbZrxTi1- xO3 (PZT) based EH. In order to compare the output performance of EH fabricated with PMN- PT compared with PZT, the similar thickness of PMN-PT and PZT thin film is deposited on stainless steel subtracted. The experimental results show that PZT-based EH had a maximum output power of 4.65 μW with 1.11 Vp-p output voltage excited at 94.4 Hz under 0.5g base excitation, while the PMN-PT based device has a maximum output power of 8.42 μW with 1.49 Vp-p output voltage at a vibration frequency of 94.8 Hz and the same base excitation level. The volumetric power density was 82.95 μW/mm3 and 48.05 μW/mm3 for the device based on PMN- PT and PZT materials, respectively. All the results demonstrate that PMN-PT has better output performance than PZT.

  16. A novel multi-degree-of-freedom thick-film ultrasonic motor.

    Science.gov (United States)

    Aoyagi, Manaba; Beeby, Steve P; White, Neil M

    2002-02-01

    This paper describes a new multi-degree-of-freedom (MDOF) ultrasonic motor that comprises few parts and is based on low-cost thick-film technology. Conventional ultrasonic motors using bulk lead zirconate titanate (PZT) or thin-film PZT layers are relatively expensive at the present time. Thick-film printed PZT technology provides the opportunity to reduce the costs of ultrasonic motors. To demonstrate the feasibility of this approach, an ultrasonic motor was fabricated from alumina using thick-film printed PZT actuators. The thick-film PZT and electrode layers were printed on a thin alumina plate, and a tiny cylinder was mounted at its center. This cylinder magnifies the lateral displacement of the stator, holds the spherical rotor, and transmits the driving force to the sphere. Three bending vibrations, B22, B30, B03, of the plate were applied to rotate the sphere. Sufficient displacements for rotating the sphere were obtained near the resonance of B22 by applying an excitation voltage of 200 V peak-to-peak via a three-phase drive circuit. Rotations in three orthogonal directions have been observed by controlling the phase of the driving signal to the PZT electrodes, and a MDOF ultrasonic motor was successfully realized.

  17. Interactions between lead-zirconate titanate, polyacrylic acid, and polyvinyl butyral in ethanol and their influence on electrophoretic deposition behavior.

    Science.gov (United States)

    Kuscer, Danjela; Bakarič, Tina; Kozlevčar, Bojan; Kosec, Marija

    2013-02-14

    Electrophoretic deposition (EPD) is an attractive method for the fabrication of a few tens of micrometer-thick piezoelectric layers on complex-shape substrates that are used for manufacturing high-frequency transducers. Niobium-doped lead-zirconate titanate (PZT Nb) particles were stabilized in ethanol using poly(acrylic acid) (PAA). With Fourier-transform infrared spectroscopy (FT-IR), we found that the deprotonated carboxylic group from the PAA is coordinated with the metal in the perovskite PZT Nb structure, resulting in a stable ethanol-based suspension. The hydroxyl group from the polyvinyl butyral added into the suspension to prevent the formation of cracks in the as-deposited layer did not interact with the PAA-covered PZT Nb particles. PVB acts as a free polymer in ethanol-based suspensions. The electrophoretic deposition of micro- and nanometer-sized PZT Nb particles from ethanol-based suspensions onto electroded alumina substrates was attempted in order to obtain uniform, crack-free deposits. The interactions between the PZT Nb particles, the PAA, and the PVB in ethanol will be discussed and related to the properties of the suspensions, the deposition yield and the morphology of the as-deposited PZT Nb thick film.

  18. Characterization of low-temperature-grown epitaxial BaPbO 3 and Pb(Zr,Ti)O 3/BaPbO 3 films on SrTiO 3 substrates

    Science.gov (United States)

    Liang, Chun-Sheng; Lee, Yi-Hsien; Wu, Jenn-Ming

    2005-10-01

    The epitaxial BaPbO 3 (BPO) and Pb(Zr,Ti)O 3 (PZT)/BPO films were grown on (0 0 1)- and (1 1 1)-oriented SrTiO 3 (STO) substrates by RF-magnetron sputtering. With the self-template of BPO buffer layer (deposited at 650 °C), BPO main layer and PZT films can be epitaxially grown at temperatures as low as 350 and 475 °C, respectively. The (0 0 1)-oriented BPO film showed a rougher surface and higher work function compared to the (2 2 2)-oriented film. The crystallinity and resistivity of BPO films were independent of their orientation. However, the crystallinity of PZT deposited afterward depends greatly on the orientation of BPO. The crystallinity of PZT deposited on BPO/STO(1 1 1) is significantly higher than that on BPO/STO(0 0 1). The remnant polarization, coercive field, dielectric constant, and resistivity of the PZT/BPO/STO(1 1 1) heterostructure were 35.54 μC/cm 2, 102.67 kV/cm, 242, and 1.1-1.6×10 11 Ω cm, respectively, which are much better than those of the PZT/BPO/STO(0 0 1) heterostructures.

  19. Electrical properties and sensing ability of novel piezoelectric ceramic fibers with Pt core

    Science.gov (United States)

    Du, Jianzhou; Qiu, Jinhao; Zhu, Kongjun; Ji, Hongli; Zhao, Huayun

    2012-04-01

    The traditional sintering method was used to sinter the pure and Fe2O3 doped 0.55Pb(Ni0.33Nb0.67)O3-0.45Pb(Zr0.3Ti0.7)O3 (abbreviate as PNN-PZT and PFNN-PZT, respectively) ceramics. The addition of Fe2O3 significantly improved the microstructure and electrical properties. Compared with pure PNN-PZT ceramics, higher dielectric and piezoelectric properties of d31~-390 pC/N, ɛ r ~6298 were obtained for the PFNN-PZT sample sintered at 1175°C for 2 h. Hence, the PFNN-PZT ceramics sample was selected to fabricate piezoelectric ceramic fibers with Pt core (PFC). Both the green fibers and bulk ceramics were sintered at 1150-1225°C for 2 h in a closed crucible, respectively. The effect of sintering temperature on the microstructure and electrical properties of the PFNN-PZT fibers was investigated. The optimal piezoelectric properties are obtained for the sample sintered at 1175°C for 2 h. The relative dielectric constant and piezoelectric constant show peak values of ɛ r~3683, d31~-197.4 pC/N, respectively. The PFC is a new type piezoelectric device, which can be used for sensors or actuators. The results of sensing experiment show that the piezoelectric ceramic fiber with Pt core has high sensitivity for the Lamb waves.

  20. Monitoring of Grouting Compactness in a Post-Tensioning Tendon Duct Using Piezoceramic Transducers.

    Science.gov (United States)

    Jiang, Tianyong; Kong, Qingzhao; Wang, Wenxi; Huo, Linsheng; Song, Gangbing

    2016-08-22

    A post-tensioning tendon duct filled with grout can effectively prevent corrosion of the reinforcement, maintain bonding behavior between the reinforcement and concrete, and enhance the load bearing capacity of concrete structures. In practice, grouting of the post-tensioning tendon ducts always causes quality problems, which may reduce structural integrity and service life, and even cause accidents. However, monitoring of the grouting compactness is still a challenge due to the invisibility of the grout in the duct during the grouting process. This paper presents a stress wave-based active sensing approach using piezoceramic transducers to monitor the grouting compactness in real time. A segment of a commercial tendon duct was used as research object in this study. One lead zirconate titanate (PZT) piezoceramic transducer with marble protection, called a smart aggregate (SA), was bonded on the tendon and installed in the tendon duct. Two PZT patch sensors were mounted on the top outside surface of the duct, and one PZT patch sensor was bonded on the bottom outside surface of the tendon duct. In the active sensing approach, the SA was used as an actuator to generate a stress wave and the PZT sensors were utilized to detect the wave response. Cement or grout in the duct functions as a wave conduit, which can propagate the stress wave. If the cement or grout is not fully filled in the tendon duct, the top PZT sensors cannot receive much stress wave energy. The experimental procedures simulated four stages during the grout pouring process, which includes empty status, half grouting, 90% grouting, and full grouting of the duct. Experimental results show that the bottom PZT sensor can detect the signal when the grout level increases towards 50%, when a conduit between the SA and PZT sensor is formed. The top PZT sensors cannot receive any signal until the grout process is completely finished. The wavelet packet-based energy analysis was adopted in this research to

  1. Monitoring of Grouting Compactness in a Post-Tensioning Tendon Duct Using Piezoceramic Transducers

    Directory of Open Access Journals (Sweden)

    Tianyong Jiang

    2016-08-01

    Full Text Available A post-tensioning tendon duct filled with grout can effectively prevent corrosion of the reinforcement, maintain bonding behavior between the reinforcement and concrete, and enhance the load bearing capacity of concrete structures. In practice, grouting of the post-tensioning tendon ducts always causes quality problems, which may reduce structural integrity and service life, and even cause accidents. However, monitoring of the grouting compactness is still a challenge due to the invisibility of the grout in the duct during the grouting process. This paper presents a stress wave-based active sensing approach using piezoceramic transducers to monitor the grouting compactness in real time. A segment of a commercial tendon duct was used as research object in this study. One lead zirconate titanate (PZT piezoceramic transducer with marble protection, called a smart aggregate (SA, was bonded on the tendon and installed in the tendon duct. Two PZT patch sensors were mounted on the top outside surface of the duct, and one PZT patch sensor was bonded on the bottom outside surface of the tendon duct. In the active sensing approach, the SA was used as an actuator to generate a stress wave and the PZT sensors were utilized to detect the wave response. Cement or grout in the duct functions as a wave conduit, which can propagate the stress wave. If the cement or grout is not fully filled in the tendon duct, the top PZT sensors cannot receive much stress wave energy. The experimental procedures simulated four stages during the grout pouring process, which includes empty status, half grouting, 90% grouting, and full grouting of the duct. Experimental results show that the bottom PZT sensor can detect the signal when the grout level increases towards 50%, when a conduit between the SA and PZT sensor is formed. The top PZT sensors cannot receive any signal until the grout process is completely finished. The wavelet packet-based energy analysis was adopted in this

  2. Properties of [Pb(Zn1/3Nb2/3)O3]x- [Pb(Zr0.48Ti0.52)O3](1-x) Ceramics With Low Sintering Temperature and Their 1-3 Piezocomposites.

    Science.gov (United States)

    Mensur-Alkoy, Ebru; Kaya, Mustafa Yunus; Avdan, Duygu; Alkoy, Sedat

    2016-06-01

    In this paper, dense ( x )PZN-( 1-x )PZT ceramics were prepared at sintering temperatures as low as 950 °C with PZN ratios of x=0.4 , 0.5, and 0.6. The 0.4PZN-0.6PZT composition was found to crystallize in the perovskite phase at this sintering temperature without the presence of any other secondary phases. Higher electrical and electromechanical properties were obtained from the 0.4PZN-0.6PZT composition compared with the x=0.5 and x=0.6 counterparts. Dielectric constant, piezoelectric charge coefficient, electromechanical coupling coefficient, and mechanical quality factor of 0.4PZN-0.6PZT were found to be 2608, 477 pC/N, 64.4, and 65, respectively. While the Curie temperature was 140 °C for pure PZN, the Curie temperature was measured as 300 °C for x=0.4 composition. Green PZN-PZT fibers with circular cross section were drawn using alginate gelation method from the 0.4PZN-0.6PZT composition. Dense fibers were obtained after the sintering process, and piezocomposites were prepared with 1-3 connectivity using fibers with an average diameter of 600 [Formula: see text]. Composites with volume fraction of 20 vol% were investigated for passive acoustic sensor applications. Electrical properties of piezocomposites were found to be scalable and compatible with the electrical properties of the bulk composition. The dielectric constant, piezoelectric charge coefficient, and maximum strain value of the PZN-PZT 1-3 piezocomposite were measured as 345, 165 pC/N, and 0.13%, respectively.

  3. In-plane orientation and composition dependences of crystal structure and electrical properties of {100}-oriented Pb(Zr,Ti)O3 films grown on (100) Si substrates by metal organic chemical vapor deposition

    Science.gov (United States)

    Okamoto, Shoji; Sankara Rama Krishnan, P. S.; Okamoto, Satoshi; Yokoyama, Shintaro; Akiyama, Kensuke; Funakubo, Hiroshi

    2017-10-01

    In-plane orientation-controlled Pb(Zr x ,Ti1‑ x )O3 (PZT) films with a thickness of approximately 2 µm and a Zr/(Zr + Ti) ratio of 0.39–0.65 were grown on (100) Si substrates by pulsed metal–organic chemical vapor deposition (MOCVD). In-plane-oriented epitaxial PZT films and in-plane random fiber-textured PZT films with {100} out-of-plane orientation were grown on (100)c SrRuO3//(100)c LaNiO3//(100) CeO2//(100) YSZ//(100) Si and (100)c SrRuO3/(100)c LaNiO3/(111) Pt/TiO2/SiO2/(100) Si substrates, respectively. The effects of Zr/(Zr + Ti) ratio and in-plane orientation on the crystal structure, dielectric, ferroelectric, and piezoelectric properties of the films were systematically investigated. The X-ray diffraction measurement showed that the epitaxial PZT films had a higher volume fraction of (100) orientation than the fiber-textured PZT films in the tetragonal Zr/(Zr + Ti) ratio region. A large difference was not detected between the epitaxial films and the fiber-textured films for Zr/(Zr + Ti) ratio dependence of the dielectric constant, and remanent polarization. However, in the rhombohedral phase region [Zr/(Zr + Ti) = 0.65], coercive field was found to be 1.5-fold different between the epitaxial and fiber-textured PZT films. The maximum field-induced strains measured at 0–100 kV/cm by scanning atomic force microscopy were obtained at approximately Zr/(Zr + Ti) = 0.50 and were about 0.5 and 0.3% for the epitaxial and fiber-textured PZT films, respectively.

  4. Preparation of lead titanate zirconate from metal citrates; Preparacao do titanato zirconato de chumbo a partir dos citratos metalicos

    Energy Technology Data Exchange (ETDEWEB)

    Bastos, C.M.R.

    1994-12-31

    Lead titanate zirconate (PZT) preparation from its metal constituent citrates have been investigated. Metal citrates were obtained by forced precipitation using a dehydration alcohol mixture. Salt solutions of lead nitrate and octahydrated zirconyl chloride, and titanium tetrachloride were treated separately with citric acid and ammonium hydroxide. Zirconium, titanium and lead oxides resulted from thermal decomposition of corresponding citrates at 500{sup 0} C, 450{sup 0} C and 250{sup 0} C, respectively. Lead titanate (PT) and lead zirconate (P Z) were obtained by calcining at 450{sup 0} C and 500{sup 0} C, respectively, after adequate heating of citrates mechanically mixed in ethyl ether. PZT samples were obtained with different starting stoichiometry. Rhombohedral PZT-1 53/47 sample was prepared from co precipitating zirconyl ammonium and ammonium lead citrates in presence of ethanolic titanium oxide dispersion, and calcinating at 800{sup 0} C. Rhombohedral PZT-q 52/48 sample was obtained from heating at 500{sup 0} C for 2 hours a mixture of metal citrates coprecipitated by dehydration mixture of acetone-ethanol-formic acid (2:1:0,06). Tetragonal PZT-m stoichiometry 53/47 sample were obtained by calcining at after 600{sup 0} C for 2 hours after heating a mechanically mixed metal citrates. PT phase arose at 400{sup 0} C. PZT-m powders obtained in a range of 400{sup 0} C-800{sup 0} C were isostatically pressed, and sintered at 1100{sup 0} C and 1200{sup 0} C in saturated Pb O atmosphere. Rhombohedral sintered PZT was obtained with 7,78 g.cm{sup -3} at 1200{sup 0} C. (author). 123 refs, 53 figs, 32 tabs.

  5. Using multi-walled carbon nanotubes in spark plasma sintered Pb(Zr0.47Ti0.53)O3 ceramics for tailoring dielectric and tunability properties

    Science.gov (United States)

    Ciomaga, Cristina E.; Padurariu, Leontin; Curecheriu, Lavinia P.; Lupu, Nicoleta; Lisiecki, Isabelle; Deluca, Marco; Tascu, Sorin; Galassi, Carmen; Mitoseriu, Liliana

    2014-10-01

    The addition of small amounts (below 0.1 wt. %) of multi-walled carbon nanotubes (MWCNTs) to Pb(Zr0.47Ti0.53)O3 (PZT) ceramics prepared by spark plasma sintering is proposed as a method of tailoring the electrical properties, which are expected to be modified with respect to the pure PZT, both as result of the presence of 1-D conductive fillers in the ceramic product and via the microstructural modifications of ceramics induced during the sintering. The addition of even small amounts of carbon nanotubes strongly reduced the sinterability of PZT ceramics and resulted in the porous and fine-grained microstructures (relative density of 73% for a MWCNT addition of 0.5 vol. % by comparison with 91% in the pure PZT, produced in the same conditions). A monotonous decrease of permittivity with increasing the MWCNT level from ˜830 in pure PZT to ˜627 for x = 0.5 vol. %, at a fixed frequency f = 1kHz, and low dielectric losses below 2% have been observed. Tunability increases with respect to the values of dense PZT for small concentration of MWCNT as high as 0.0625 vol. % and then monotonically decreases for higher additions. Calculations by finite element modeling demonstrated that by addition of 1-D conductive fillers with compositions below the percolation limits to porous microstructures, the major role in changing the electrical properties via local field modification is related to the induced porosity rather than to the influence of the small amounts of MWCNTs survived after sintering and post-annealing treatment. The reduced permittivity with about 14% combined with low losses and higher tunability than in the pure PZT ceramics obtained at reasonable fields, makes the idea of using the addition of MWCNTs to ferroelectric ceramics an interesting approach in searching new structures for tunability properties.

  6. Excitation of fundamental shear horizontal wave by using face-shear (d36) piezoelectric ceramics

    Science.gov (United States)

    Miao, Hongchen; Dong, Shuxiang; Li, Faxin

    2016-05-01

    The fundamental shear horizontal (SH0) wave in plate-like structures is extremely useful for non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive. However, currently, the SH0 wave is usually excited by electromagnetic acoustic transducers (EMAT) whose energy conversion efficiency is fairly low. The face-shear ( d 36 ) mode piezoelectrics is more promising for SH0 wave excitation, but this mode cannot appear in conventional piezoelectric ceramics. Recently, by modifying the symmetry of poled PbZr1-xTixO3 (PZT) ceramics via ferroelastic domain engineering, we realized the face-shear d 36 mode in both soft and hard PZT ceramics. In this work, we further improved the face-shear properties of PZT-4 and PZT-5H ceramics via lateral compression under elevated temperature. It was found that when bonded on a 1 mm-thick aluminum plate, the d 36 type PZT-4 exhibited better face-shear performance than PZT-5H. We then successfully excite SH0 wave in the aluminum plate using a face-shear PZT-4 square patch and receive the wave using a face-shear 0.72[Pb(Mg1/3Nb2/3)O3]-0.28[PbTiO3] (PMN-PT) patch. The frequency response and directionality of the excited SH0 wave were also investigated. The SH0 wave can be dominated over the Lamb waves (S0 and A0 waves) from 160 kHz to 280 kHz. The wave amplitude reaches its maxima along the two main directions (0° and 90°). The amplitude can keep over 80% of the maxima when the deviate angle is less than 30°, while it vanishes quickly at the 45° direction. The excited SH0 wave using piezoelectric ceramics could be very promising in the fields of NDT and SHM.

  7. Health monitoring of cuplok scaffold joint connection using piezoceramic transducers and time reversal method

    Science.gov (United States)

    Zhang, Liuyu; Wang, Chenyu; Huo, Linsheng; Song, Gangbing

    2016-03-01

    Cuplok scaffolds are widely used to form temporary supporting structures when constructing bridges and other structures all over the world. The safety and stability of cuplok scaffolds are important issues during construction. Cuplok scaffolds are subjected to various types of vibrations, which may loosen the cuplok connection, negatively impacting the stability of the structure and even leading to severe accidents. In this paper, the authors propose a time reversal (TR) method to monitor the looseness status of the cuplok connection by using stress wave-based active sensing. Lead zirconate titanate (PZT), a commonly used piezoceramic material with a strong piezoelectric effect, is employed. In the proposed approach, PZT patches are used as sensors and actuators to monitor the cuplok joint looseness. One PZT patch is bonded to the vertical bar and two PZT patches are bonded to the cross bars of the cuplok scaffold. The PZT patch on the vertical bar is used as an actuator to generate a stress wave and the other two PZT patches are used as sensors to detect the propagated waves through the cuplok connection, the looseness of which will directly impact the stress wave propagation. The TR method is used to analyse the transmitted signal between the PZT patches through the cuplok connection. By comparing the peak values of the TR focused signal, it can be found that the peak value increases as the tightness of the cuplok connection increases. Therefore, the peak value of the TR focused signal can be used to monitor the tightness of the cuplok connection. In addition, the experimental results demonstrated that the TR method is superior to the energy method in consistency, sensitivity and anti-noise properties.

  8. Ferroelectric and piezoelectric responses of (110) and (001)-oriented epitaxial Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3} thin films on all-oxide layers buffered silicon

    Energy Technology Data Exchange (ETDEWEB)

    Vu, Hien Thu [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology, No.1 Dai Co Viet Road, Hanoi 10000 (Viet Nam); Nguyen, Minh Duc, E-mail: minh.nguyen@itims.edu.vn [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology, No.1 Dai Co Viet Road, Hanoi 10000 (Viet Nam); Inorganic Materials Science (IMS), MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); SolMateS B.V., Drienerlolaan 5, Building 6, 7522 NB Enschede (Netherlands); Houwman, Evert; Boota, Muhammad [Inorganic Materials Science (IMS), MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Dekkers, Matthijn [SolMateS B.V., Drienerlolaan 5, Building 6, 7522 NB Enschede (Netherlands); Vu, Hung Ngoc [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology, No.1 Dai Co Viet Road, Hanoi 10000 (Viet Nam); Rijnders, Guus [Inorganic Materials Science (IMS), MESA + Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

    2015-12-15

    Graphical abstract: The cross sections show a very dense structure in the (001)-oriented films (c,d), while an open columnar growth structure is observed in the case of the (110)-oriented films (a,b). The (110)-oriented PZT films show a significantly larger longitudinal piezoelectric coefficient (d33{sub ,f}), but smaller transverse piezoelectric coefficient (d31{sub ,f}) than the (001) oriented films. - Highlights: • We fabricate all-oxide, epitaxial piezoelectric PZT thin films on Si. • The orientation of the films can be controlled by changing the buffer layer stack. • The coherence of the in-plane orientation of the grains and grain boundaries affects the ferroelectric properties. • Good cycling stability of the ferroelectric properties of (001)-oriented PZT thin films. The (110)-oriented PZT thin films show a larger d33{sub ,f} but smaller d31{sub ,f} than the (001)-oriented films. - Abstract: Epitaxial ferroelectric Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3} (PZT) thin films were fabricated on silicon substrates using pulsed laser deposition. Depending on the buffer layers and perovskite oxide electrodes, epitaxial films with different orientations were grown. (110)-oriented PZT/SrRuO{sub 3} (and PZT/LaNiO{sub 3}) films were obtained on YSZ-buffered Si substrates, while (001)-oriented PZT/SrRuO{sub 3} (and PZT/LaNiO{sub 3}) were fabricated with an extra CeO{sub 2} buffer layer (CeO{sub 2}/YSZ/Si). There is no effect of the electrode material on the properties of the films. The initial remnant polarizations in the (001)-oriented films are higher than those of (110)-oriented films, but it increases to the value of the (001) films upon cycling. The longitudinal piezoelectric d33{sub ,f} coefficients of the (110) films are larger than those of the (001) films, whereas the transverse piezoelectric d31{sub ,f} coefficients in the (110)-films are less than those in the (001)-oriented films. The difference is ascribed to the lower density (connectivity between

  9. Fabrication and modeling of piezoelectric transducers for High-Frequency medical imaging

    CERN Document Server

    Abellard, André-Pierre; Holc, Janez; Levassort, Franck; Noshchenko, Oleksandr; Lethiecq, Marc; Kosec, Marija

    2013-01-01

    We have studied the processing of piezoelectric thick films using electrophoretic deposition (EPD) for high-frequency ultrasound applications. Lead-zirconium-titanate (PZT) particles synthetized by solid states synthesis were dispersed in ethanol using ammonium polyacrylate (PAA). The electrophoretic deposition of PZT particles was performed at a constant-current mode. PZT thick-films deposited at 1 mA for 60 seconds were sintered at 900oC for 2 hours in a PbO-controlled atmosphere. The scanning-electron microscopy (SEM) analysis shows that the thickness of PZT layer is uniform and that the pores are homogeneously distributed within the layer. The complex electrical impedance was measured and fitted by KLM scheme in order to deduce the dielectric, mechanical and piezoelectric parameters of the thick-films. The density and thickness of PZT thick films are used as inputs and the thickness coupling factor kt, dielectric constant at constant strain and resonant frequency are deduced. The results show that homogen...

  10. Dielectric relaxation analysis of Pb(Zr0.54,Ti0.46)O3 thin films: Electric field dependence

    Science.gov (United States)

    Ponchel, F.; Sama, N.; Rémiens, D.; Lasri, T.

    2014-12-01

    350 nm-thick Perovskite PbZr0.54Ti0.46O3 (PZT) thin films were deposited on Al2O3 substrates by sputtering with and without an additional 10-nm-thick TiOx buffer layer. X-ray diffraction patterns showed that in presence of TiOx buffer layer, PZT film was highly oriented along the (111) direction film, whereas the unbuffered, counterpart was polycrystalline. A full wave electromagnetic analysis using a vector finite element method was performed to determine the tunability and the complex permittivity up to 67 GHz. A comparison between the electromagnetic analysis and Cole-Cole relaxation model was proposed. Through an original study of the relaxation time as a function of the electric field, values, such as 2 ps and 0.6 ps, were estimated for EDC = 0 kV/cm and 235 kV/cm, respectively, and in both cases (111)-PZT and polycrystalline-PZT. The distribution of relaxation times is found to be larger for (111)-PZT film, which is probably related to the film microstructure.

  11. Dielectric relaxation analysis of Pb(Zr{sub 0.54},Ti{sub 0.46})O{sub 3} thin films: Electric field dependence

    Energy Technology Data Exchange (ETDEWEB)

    Ponchel, F., E-mail: freddy.ponchel@univ-valenciennes.fr; Rémiens, D. [Institute of Electronics, Microelectronics and Nanotechnology (IEMN), UMR CNRS 8520, DOAE Department, University of Valenciennes et du Hainaut Cambresis, Le Mont Houy, 59313 Valenciennes Cedex 9 (France); Sama, N. [Institut National de la Recherche Scientifique - Energie Matériaux et Télécommunications (INRS-EMT), 10 1650 Boulevard Lionel Boulet, Varennes, Quebec J3X 1S2 (Canada); Lasri, T. [Institute of Electronics, Microelectronics and Nanotechnology (IEMN), UMR CNRS 8520, DHS Department, University of Lille1 Sciences and Technologies, 59652 Villeneuve d' Ascq Cedex (France)

    2014-12-28

    350 nm-thick Perovskite PbZr{sub 0.54}Ti{sub 0.46}O{sub 3} (PZT) thin films were deposited on Al{sub 2}O{sub 3} substrates by sputtering with and without an additional 10-nm-thick TiO{sub x} buffer layer. X-ray diffraction patterns showed that in presence of TiO{sub x} buffer layer, PZT film was highly oriented along the (111) direction film, whereas the unbuffered, counterpart was polycrystalline. A full wave electromagnetic analysis using a vector finite element method was performed to determine the tunability and the complex permittivity up to 67 GHz. A comparison between the electromagnetic analysis and Cole-Cole relaxation model was proposed. Through an original study of the relaxation time as a function of the electric field, values, such as 2 ps and 0.6 ps, were estimated for E{sub DC} = 0 kV/cm and 235 kV/cm, respectively, and in both cases (111)-PZT and polycrystalline-PZT. The distribution of relaxation times is found to be larger for (111)-PZT film, which is probably related to the film microstructure.

  12. Fabrication and characterization of Pb(Zr 0.53,Ti 0.47)O 3-Pb(Nb 1/3,Zn 2/3)O 3 thin films on cantilever stacks

    KAUST Repository

    Fuentes-Fernandez, E. M A

    2010-11-18

    0.9Pb(Zr 0.53,Ti 0.47)O 3-0.1Pb(Zn 1/3,Nb 2/3)O 3 (PZT-PZN) thin films and integrated cantilevers have been fabricated. The PZT-PZN films were deposited on SiO 2/Si or SiO 2/Si 3N 4/SiO 2/poly-Si/Si membranes capped with a sol-gel-derived ZrO 2 buffer layer. It is found that the membrane layer stack, lead content, existence of a template layer of PbTiO 3 (PT), and ramp rate during film crystallization are critical for obtaining large-grained, single-phase PZT-PZN films on the ZrO 2 surface. By controlling these parameters, the electrical properties of the PZT-PZN films, their microstructure, and phase purity were significantly improved. PZT-PZN films with a dielectric constant of 700 to 920 were obtained, depending on the underlying stack structure. © 2010 TMS.

  13. The annealing induced extraordinary properties of SI based ZNO film grown by RF sputtering

    CERN Document Server

    Li, Jing; Wu, Suntao

    2007-01-01

    Pb(Zr0.52Ti0.48)O3 (PZT) thin films were in situ deposited by pulsed laser deposition (PLD) on Pt/Ti/SiO2/Si substrates using a template layer derived by sol-gel method. A 0.1-$\\mu$m-thick PZT layer with (111) or (100)-preferred orientation was first deposited onto Pt/Ti/SiO2/Si substrates using the sol-gel method, and than a PZT layer with thickness of 1$\\mu$m was in situ deposited by PLD on the above-mentioned PZT layer. The crystalline phases and the preferred orientations of the PZT films were investigated by X-ray diffraction analysis. Surface and cross-sectional morphologies were observed by scanning electron microscopy and transmission electron microscopy. The electrical properties of the films were evaluated by measuring their P-E hysteresis loops and dielectric constants. The preferred orientation of the films can be controlled using the template layer derived by the sol-gel method. The deposition temperature required to obtain the perovskite phase in this process is approximately 460 degrees C, and ...

  14. Electromechanical Impedance Response of a Cracked Timoshenko Beam

    Directory of Open Access Journals (Sweden)

    Cuiqin Wu

    2011-07-01

    Full Text Available Typically, the Electromechanical Impedance (EMI technique does not use an analytical model for basic damage identification. However, an accurate model is necessary for getting more information about any damage. In this paper, an EMI model is presented for predicting the electromechanical impedance of a cracked beam structure quantitatively. A coupled system of a cracked Timoshenko beam with a pair of PZT patches bonded on the top and bottom surfaces has been considered, where the bonding layers are assumed as a Kelvin-Voigt material. The shear lag model is introduced to describe the load transfer between the PZT patches and the beam structure. The beam crack is simulated as a massless torsional spring; the dynamic equations of the coupled system are derived, which include the crack information and the inertial forces of both PZT patches and adhesive layers. According to the boundary conditions and continuity conditions, the analytical expression of the admittance of PZT patch is obtained. In the case study, the influences of crack and the inertial forces of PZT patches are analyzed. The results show that: (1 the inertial forces affects significantly in high frequency band; and (2 the use of appropriate frequency range can improve the accuracy of damage identification.

  15. Study on Pyroelectric Harvesters with Various Geometry

    Directory of Open Access Journals (Sweden)

    An-Shen Siao

    2015-08-01

    Full Text Available Pyroelectric harvesters convert time-dependent temperature variations into electric current. The appropriate geometry of the pyroelectric cells, coupled with the optimal period of temperature fluctuations, is key to driving the optimal load resistance, which enhances the performance of pyroelectric harvesters. The induced charge increases when the thickness of the pyroelectric cells decreases. Moreover, the induced charge is extremely reduced for the thinner pyroelectric cell when not used for the optimal period. The maximum harvested power is achieved when a 100 μm-thick PZT (Lead zirconate titanate cell is used to drive the optimal load resistance of about 40 MΩ. Moreover, the harvested power is greatly reduced when the working resistance diverges even slightly from the optimal load resistance. The stored voltage generated from the 75 μm-thick PZT cell is less than that from the 400 μm-thick PZT cell for a period longer than 64 s. Although the thinner PZT cell is advantageous in that it enhances the efficiency of the pyroelectric harvester, the much thinner 75 μm-thick PZT cell and the divergence from the optimal period further diminish the performance of the pyroelectric cell. Therefore, the designers of pyroelectric harvesters need to consider the coupling effect between the geometry of the pyroelectric cells and the optimal period of temperature fluctuations to drive the optimal load resistance.

  16. Impact localization on composite structures using time difference and MUSIC approach

    Science.gov (United States)

    Zhong, Yongteng; Xiang, Jiawei

    2017-05-01

    1-D uniform linear array (ULA) has the shortcoming of the half-plane mirror effect, which does not allow discriminating between a target placed above the array and a target placed below the array. This paper presents time difference (TD) and multiple signal classification (MUSIC) based omni-directional impact localization on a large stiffened composite structure using improved linear array, which is able to perform omni-directional 360° localization. This array contains 2M+3 PZT sensors, where 2M+1 PZT sensors are arranged as a uniform linear array, and the other two PZT sensors are placed above and below the array. Firstly, the arrival times of impact signals observed by the other two sensors are determined using the wavelet transform. Compared with each other, the direction range of impact source can be decided in general, 0°to 180° or 180°to 360°. And then, two dimensional multiple signal classification (2D-MUSIC) based spatial spectrum formula using the uniform linear array is applied for impact localization by the general direction range. When the arrival times of impact signals observed by upper PZT is equal to that of lower PZT, the direction can be located in x axis (0°or 180°). And time difference based MUSIC method is present to locate impact position. To verify the proposed approach, the proposed approach is applied to a composite structure. The localization results are in good agreement with the actual impact occurring positions.

  17. Synthesis and Raman scattering of multiferroic Fe-Pb(Zr{sub 0.2}Ti{sub 0.8})O{sub 3} core-shell wire arrays

    Energy Technology Data Exchange (ETDEWEB)

    Baibarac, Mihaela; Sima, Marian; Matei, Elena; Pasuk, Iuliana; Mihut, Lucian [National Institute of Materials Physics, Magurele (Romania)

    2014-01-15

    A new method to fabricate an Fe-PZT core-shell wire arrays developed in three steps is reported in this paper. This involves the electrochemical growth of an iron wire array by template method, deposition by spin coating of the PZT precursor prepared by sol-gel technique on the iron wires surface and annealing treatment to obtain Fe-PZT core-shell structures. The structure of the Fe-PZT core-shell wire array was characterized by scanning electron microscopy (SEM) and Raman scattering. Raman lines situated at 372 and 575 cm{sup -1} indicate the formation of the FeO particles on the Fe wires surface as a result of the use of an aqueous solution for electrochemical synthesis. An upshift of Raman lines of Fe decorated with FeO wires was observed after formation of Fe-PZT core-shell structure. The annealing treatment of this structure involves a partial transformation of the FeO into Fe{sub 2}O{sub 3} particles both with structure rhombohedral and cubic that were evidenced by Raman lines peaked at 243 and 497 cm{sup -1}, respectively. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  18. Study on polarization characteristics of BiFeO3 thin films prepared by sol-gel spin-coating technology

    Science.gov (United States)

    Jia, Ze; Wu, Xiao; Zhang, Mingming; Xu, Jianlong; Zhang, Naiwen; Liou, Juin J.

    2015-07-01

    The ferroelectric polarization properties of bismuth ferrite (BFO) thin films deposited on Pt(111)/TiO2/SiO2/Si(100) substrates by sol-gel spin-coating technology affected by the processes and dopants have been studied and analyzed tentatively. The results indicate BFO thin film should be introduced to a rapid thermal annealing (RTA) process at N2 atmosphere. The enhanced ferroelectric polarization properties were observed in Mn and La doped BFO thin films, because ion substitution may improve the inherent volatility of Bi atoms, valence fluctuation of Fe ions and magnetic spin structures, reducing the formation of oxygen vacancies. The increased remnant polarization observed in the BFO thin film with a lead zirconate titanate (PZT) seeding layer has also been analyzed as the probable results of small changes of lattice parameters caused by constraint stress, reduced defects and decreased leakage current density, which are contributed by the PZT seeding layer possibly. Moreover, the remnant polarization approximately 79 μC/cm2 is observed in (Bi0.95La0.05)FeO3 (BLFO) thin film with a PZT seeding layer, which is twice and treble the values of BFO thin films with and without a PZT seeding layer, indicating PZT seeding layer is much more effective for BLFO thin film which has a substitution at A site.

  19. Synthesis and Characterization of Pb(Zr., Ti.O-Pb(Nb/, Zn/O Thin Film Cantilevers for Energy Harvesting Applications

    Directory of Open Access Journals (Sweden)

    E. M. A. Fuentes-Fernandez

    2012-01-01

    Full Text Available A complete analysis of the morphology, crystallographic orientation, and resulting electrical properties of Pb(Zr0.53,Ti0.47O3− Pb(Nb1/3, Zn2/3O3 (PZT-PZN thin films, as well as the electrical behavior when integrated in a cantilever for energy harvesting applications, is presented. The PZT-PZN films were deposited using sol-gel methods. We report that using 20% excess Pb, a nucleation layer of PbTiO3 (PT, and a fast ramp rate provides large grains, as well as denser films. The PZT-PZN is deposited on a stack of TiO2/PECVD SiO2/Si3N4/thermal SiO2/Poly-Si/Si. This stack is designed to allow wet-etching the poly-Si layer to release the cantilever structures. It was also found that the introduction of the poly-Si layer results in larger grains in the PZT-PZN film. PZT-PZN films with a dielectric constant of 3200 and maximum polarization of 30 μC/cm2 were obtained. The fabricated cantilever devices produced ~300–400 mV peak-to-peak depending on the cantilever design. Experimental results are compared with simulations.

  20. ANALYSIS OF CRACK-TIP SINGULARITIES FOR AN INTERFACIAL PERMEABLE CRACK IN METAL/PIEZOELECTRIC BIMATERIALS

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    By modeling metal as a special piezoelectric material with extremely small piezoelectricity and extremely large permittivity, we have obtained the analytical solutions for an interfacial permeable crack in metal/piezoelectric bimaterials by means of the generalized Stroh formalism.The analysis shows that the stress fields near a permeable interfacial crack tip are usually with three types of singularities: r-1/2±iε and r-1/2. Further numerical calculation on the oscillatory index ε are given for 28 types of metal/piezoelectric bimaterials combined by seven commercial piezoelectric materials: PZT-4, BaTiO3, PZT-5H, PZT-6B, PZT-7A, P-7 and PZT-PIC 151 and four metals: copper, silver, lead and aluminum, respectively. The explicit expressions of the crack tip energy release rate (ERR) and the crack tip generalized stress intensity factors (GSIF) are obtained. It is found that both the ERR and GSIF are independent of the electric displacement loading, although they seriously depends on the mechanical loadings.