Oxidative desulfurization of tire pyrolysis oil

OpenAIRE

Ahmad Shahzad; Ahmad Muhammad Imran; Naeem Khawar; Humayun Muhammad; Sebt-E-Zaeem; Faheem Farrukh

2016-01-01

This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure a...

Recycling of waste engine oil for diesel production.

Science.gov (United States)

Maceiras, R; Alfonsín, V; Morales, F J

2017-02-01

The aim of this work was to recycle waste engine oil until converting it into reusable product, diesel fuel. The waste oil was treated using pyrolytic distillation. The effect of two additives (sodium hydroxide and sodium carbonate) in the purification of the obtained fuel was also studied. Moreover, the influence of the number of distillations were analysed. Some thermal and physicochemical properties (density, viscosity, colour, turbidity, acidity value, distillation curves, cetane number, corrosiveness to Cu, water content, flash point and hydrocarbons) were determined to analyse the quality of the obtained fuel. The best results were obtained with 2% of sodium carbonate and two successive distillations. The obtained results showed that pyrolytic distillation of waste engine oil is an excellent way to produce diesel fuel to be used in engines. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolytic 3D Carbon Microelectrodes for Electrochemistry

DEFF Research Database (Denmark)

Hemanth, Suhith; Caviglia, Claudia; Amato, Letizia

2016-01-01

This work presents the fabrication and characterization of suspended three-dimensional (3D) pyrolytic carbon microelectrodes for electrochemical applications. For this purpose, an optimized process with multiple steps of UV photolithography with the negative tone photoresist SU-8 followed...... by pyrolysis at 900ºC for 1h was developed. With this process, microelectrode chips with a three electrode configuration were fabricated and characterized with cyclic voltammetry (CV) using a 10mM potassium ferri-ferrocyanide redox probe in a custom made batch system with magnetic clamping. The 3D pyrolytic...... carbon microelectrodes displayed twice the higher peak current compared to 2D....

Effect of filling surface-treated pyrolytic char on resistivity of rubber films

Directory of Open Access Journals (Sweden)

Pattraporn Yamkaya

2015-03-01

Full Text Available In this research, natural rubber (NR films filled with pyrolytic tire char, carbon black N234 and N330 were compared for their electrical resistivity. The filler loading was varied to be 5, 10, 15, 20 and 25% of dry rubber content. The effect of surfactant which is 2 %w/v sodium dodecyl sulfate (SDS was also investigated. In the experiments, it was necessary to disperse the pyrolytic char in ethyl alcohol while disperse carbon black (CB in ammonium hydroxide solution prior to mixing with the rubber latex and the filled NR film was prepared by casting the mixture on a plate. It was found that increasing the amount of pyrolytic char in the NR film could lower its resistivity. The surfactant, SDS, could help better dispersion of both CB and pyrolytic char, thereby decreasing the resistivity. In a separate experiment where hexane vapor was absorbed in NR film without surfactant, in the first 30 seconds, the rate of increasing resistivity of the CB-filled film was not seen as clearly as that of pyrolytic-char-filled film. For the films with surfactant, the slow increase in resistivity of the NR films filled with N330 and pyrolytic char during adsorbing hexane vapor was observed.

Pyrolitics Oils in Coal Flotation

Czech Academy of Sciences Publication Activity Database

Čáblík, V.; Išek, J.; Herková, M.; Halas, J.; Čáblíková, L.; Vaculíková, Lenka

2014-01-01

Roč. 34, č. 2 (2014), s. 9-14 ISSN 1640-4920 Institutional support: RVO:68145535 Keywords : pyrolytic oils * flotation, black coal * new flotation reagents Subject RIV: CB - Analytical Chemistry, Separation http://homen.vsb.cz/hgf/546/IM_2014_02.pdf

Conversion of hydrocarbon oils into motor fuels

Energy Technology Data Exchange (ETDEWEB)

1937-11-09

The abstract describes a process for producing lower boiling hydrocarbon motor fuels with a starting material of wide boiling range composed primarily of hydrocarbon oils boiling substantially above the boiling range of the desired product. Separate catalytic and pyrolytic conversion zones are simultaneously maintained in an interdependent relationship. Higher boiling constituents are separated from residual constituents by fractionation while desirable reaction conditions are maintained. All or at least a portion of the products from the catalytic and pyrolytic conversion zones are blended to yield the desired lower boiling hydrocarbons or motor fuels.

Aromatics extraction from pyrolytic sugars using ionic liquid to enhance sugar fermentability

NARCIS (Netherlands)

Li, X.; Luque-Moreno, L.C.; Oudenhoven, Stijn; Rehmann, L.; Kersten, Sascha R.A.; Schuur, Boelo

2016-01-01

Fermentative bioethanol production from pyrolytic sugars was improved via aromatics removal by liquid–liquid extraction. As solvents, the ionic liquid (IL) trihexyltetradecylphosphonium dicyanamide (P666,14[N(CN)2]) and ethyl acetate (EA) were compared. Two pyrolytic sugar solutions were created

Adsorption of Pb(II by Activated Pyrolytic Char from Used Tire

Directory of Open Access Journals (Sweden)

Lu Ping

2016-01-01

Full Text Available As a renewable resource, the pyrolytic char derived from used tire has promising adsorption capacities owing to its similar structure and properties with active carbon. The purification and activation of the pyrolytic char from used tire, as well as the application of this material in the adsorption of Pb(II in water is conducted. The influences on the adsorption capacity by temperature and pH value are investigated and discussed; the adsorption thermodynamics and kinetics are also studied. The results show that the pyrolytic char from used tire has remarkable adsorption capacity for Pb(II, and the adsorption is an endothermic process complying with the Langmuir isotherm. The adsorption kinetics is a pseudo second-order reaction.

Early outcomes of pyrolytic carbon hemiarthroplasty for the treatment of trapezial-metacarpal arthritis

NARCIS (Netherlands)

Martinez de Aragon, J. S.; Moran, Steven L.; Rizzo, Marco; Reggin, Kirsten B.; Beckenbaugh, Robert D.

2009-01-01

PURPOSE: Pyrolytic carbon implants have been successfully used in the treatment of osteoarthritis of the metacarpophalangeal and proximal interphalangeal joints. Recently, pyrolytic carbon hemiarthroplasties have been proposed for the treatment of osteoarthritis of the trapezial-metacarpal (TM)

Characterization and Catalytic Upgrading of Crude Bio-oil Produced by Hydrothermal Liquefaction of Swine Manure and Pyrolysis of Biomass

Science.gov (United States)

Cheng, Dan

ethanol to acetic acid ratio of 3. Crude pyrolytic oil obtained from the RTI International had distillation temperatures from 164.8°C to 365.5°C and 50% volumetric fraction of the crude bio-oil was distillable. Esterified pyrolytic bio-oil had an increased distillability up to 55% volumetric fraction. The esterified pyrolytic bio-oil had an increased pH of 6.12. Diesel range pyrolytic bio-oil distilled from esterified pyrolytic bio-oil had quite comparable properties with commercial diesel, with an energy content of 41.41 MJ/kg, water content of 0.58 wt%, and viscosity of 7.45 cP.

Physical and Chemical Properties of Bio-Oils From Microwave Pyrolysis of Corn Stover

Science.gov (United States)

Yu, Fei; Deng, Shaobo; Chen, Paul; Liu, Yuhuan; Wan, Yiqin; Olson, Andrew; Kittelson, David; Ruan, Roger

This study was aimed to understand the physical and chemical properties of pyrolytic bio-oils produced from microwave pyrolysis of corn stover regarding their potential use as gas turbine and home heating fuels. The ash content, solids content, pH, heating value, minerals, elemental ratio, moisture content, and viscosity of the bio-oils were determined. The water content was approx 15.2 wt%, solids content 0.22 wt%, alkali metal content 12 parts per million, dynamic viscosity 185 mPa·s at 40°C, and gross high heating value 17.5 MJ/kg for a typical bio-oil produced. Our aging tests showed that the viscosity and water content increased and phase separation occurred during the storage at different temperatures. Adding methanol and/or ethanol to the bio-oils reduced the viscosity and slowed down the increase in viscosity and water content during the storage. Blending of methanol or ethanol with the bio-oils may be a simple and cost-effective approach to making the pyrolytic bio-oils into a stable gas turbine or home heating fuels.

The vacuum pyrolysis of used tires. End-uses for oil and carbon black products

Energy Technology Data Exchange (ETDEWEB)

Roy, C.; Chaala, A.; Darmstadt, H. [Institut Pyrovac Inc., Parc Technologique du Quebec Metropolitain, rue Franquet, Sainte-Foy (Canada)

1999-07-01

By vacuum pyrolysis, the rubber portion of used tires is transformed into oil and gas and the carbon black filler is recovered as pyrolytic carbon black (CB{sub P}). Several commercial applications for the different products have been investigated and are reported in this article. CB{sub P} surface chemistry and activity are similar to those of commercial carbon blacks. Therefore, CB{sub P} has the potential to replace commercial carbon black grades in certain rubber applications. CB{sub P} was successfully tested as a filler in road pavement. The total pyrolytic oil can be used as a liquid fuel. The oil can also be distilled into different fractions: a light, a middle distillate and a heavy fraction. The light fraction was positively tested as a gasoline additive. Furthermore, this fraction contains valuable chemicals such as d,l-limonene. The middle fraction was successfully tested as a plasticizer in rubbers. The heavy fraction represents a good-quality feedstock for the production of coke and can also be used in road pavements. The pyrolytic gas can be used as a make-up heat source for the pyrolysis process

Tailoring stress in pyrolytic carbon for fabrication of nanomechanical string resonators

DEFF Research Database (Denmark)

Quang, Long Nguyen; Larsen, Peter Emil; Boisen, Anja

2018-01-01

In order to achieve high resonance frequencies and quality factors of pyrolytic carbon MEMS string resonators the resonator material needs to have a large tensile stress. In this study, the influence of pyrolysis temperature, dwell time and ramping rate on the residual stress in thin pyrolytic...... carbon films is investigated with the bending plate method. The results show that the pyrolysis temperature is the most important parameter for tailoring the residual stress, with a transition from tensile stress at temperature below 800ºC to compressive stress at temperatures above 800ºC. Two kinds...... of photoresist: positive (AZ5214E) and negative (SU-8) and different pyrolysis conditions are used to fabricate pyrolytic carbon string resonators at variable pyrolysis conditions. The best performance is obtained for devices with a length of 400 µm fabricated at a pyrolysis temperature of 700ºC, ramping rate...

Damage to the microbial cell membrane during pyrolytic sugar utilization and strategies for increasing resistance.

Science.gov (United States)

Jin, Tao; Rover, Marjorie R; Petersen, Elspeth M; Chi, Zhanyou; Smith, Ryan G; Brown, Robert C; Wen, Zhiyou; Jarboe, Laura R

2017-09-01

Lignocellulosic biomass is an appealing feedstock for the production of biorenewable fuels and chemicals, and thermochemical processing is a promising method for depolymerizing it into sugars. However, trace compounds in this pyrolytic sugar syrup are inhibitory to microbial biocatalysts. This study demonstrates that hydrophobic inhibitors damage the cell membrane of ethanologenic Escherichia coli KO11+lgk. Adaptive evolution was employed to identify design strategies for improving pyrolytic sugar tolerance and utilization. Characterization of the resulting evolved strain indicates that increased resistance to the membrane-damaging effects of the pyrolytic sugars can be attributed to a glutamine to leucine mutation at position 29 of carbon storage regulator CsrA. This single amino acid change is sufficient for decreasing EPS protein production and increasing membrane integrity when exposed to pyrolytic sugars.

Pyrolytic Treatment and Fertility Enhancement of Soils Contaminated with Heavy Hydrocarbons.

Science.gov (United States)

Vidonish, Julia E; Zygourakis, Kyriacos; Masiello, Caroline A; Gao, Xiaodong; Mathieu, Jacques; Alvarez, Pedro J J

2016-03-01

Pyrolysis of contaminated soils at 420 °C converted recalcitrant heavy hydrocarbons into "char" (a carbonaceous material similar to petroleum coke) and enhanced soil fertility. Pyrolytic treatment reduced total petroleum hydrocarbons (TPH) to below regulatory standards (typically hydrocarbons (PAHs) was not observed, with post-pyrolysis levels well below applicable standards. Plant growth studies showed a higher biomass production of Arabidopsis thaliana and Lactuca sativa (Simpson black-seeded lettuce) (80-900% heavier) in pyrolyzed soils than in contaminated or incinerated soils. Elemental analysis showed that pyrolyzed soils contained more carbon than incinerated soils (1.4-3.2% versus 0.3-0.4%). The stark color differences between pyrolyzed and incinerated soils suggest that the carbonaceous material produced via pyrolysis was dispersed in the form of a layer coating the soil particles. Overall, these results suggest that soil pyrolysis could be a viable thermal treatment to quickly remediate soils impacted by weathered oil while improving soil fertility, potentially enhancing revegetation.

High-temperature properties of commercial pyrolytic graphite

International Nuclear Information System (INIS)

Goetzel, C.G.

1979-01-01

Pyrolytic graphite is produced commercially as free-standing massive structures of continuously-nucleated and surface-nucleated varieties. Both are used for rocket nozzle components. The major design-significant thermal and mechanical properties of both material types are presented as a function of temperature up to 3000 K. They are compared with each other and with previous data. (author)

Sealing nuclear graphite with pyrolytic carbon

International Nuclear Information System (INIS)

Feng, Shanglei; Xu, Li; Li, Li; Bai, Shuo; Yang, Xinmei; Zhou, Xingtai

2013-01-01

Pyrolytic carbon (PyC) coatings were deposited on IG-110 nuclear graphite by thermal decomposition of methane at ∼1830 °C. The PyC coatings are anisotropic and airtight enough to protect IG-110 nuclear graphite against the permeation of molten fluoride salts and the diffusion of gases. The investigations indicate that the sealing nuclear graphite with PyC coating is a promising method for its application in Molten Salt Reactor (MSR)

Pyrolytic carbon coatings for nuclear fuels from commercial butane

International Nuclear Information System (INIS)

Abdelrazek, I.D.; Abdelhalim, A.S.

1976-01-01

Uranium dioxide and graphite semi-spherical particles (average diameter = 300 um) were coated with pyrolytic carbon at relatively low temperatures (800 to 1200 0 C). The spouting gas was a mixture of commercial butane and nitrogen. The hydrocarbon served as a source for carbon whereas nitrogenated as a diluent and a support for the bed. The total gas flow rate was 3.5 lit/min and the hydrocarbon content varied from 3 to 10%. Coating efficiencies ranging from 4 to 25 percent were obtained. The densities of the coatings varied from 1.25 g/cm 3 (which corresponds to coatings of laminar microstructures) and 1.82 g/cm 3 (which suggests the formation of isotropic coatings. Metallographic examination (using polarized light) of the pyrolytic carbon formed at the experimental conditions indicated the possibility of using the coatings for nuclear fuel applications

Improvement on the electrochemical characteristics of graphite anodes by coating of the pyrolytic carbon using tumbling chemical vapor deposition

International Nuclear Information System (INIS)

Han, Young-Soo; Lee, Jai-Young

2003-01-01

The electrochemical characteristics of graphite coated with pyrolytic carbon materials using tumbling chemical vapor deposition (CVD) process have been studied for the active material of anodes in lithium ion secondary batteries. Coating of pyrolytic carbons on the surface of graphite particles, which tumble in a rotating reactor tube, was performed through the pyrolysis of liquid propane gas (LPG). The surface morphology of these graphite particles coated with pyrolytic carbon has been observed with scanning electron microscopy (SEM). The surface of graphite particles can well be covered with pyrolytic carbon by tumbling CVD. High-resolution transmission electron microscopy (HRTEM) image of these carbon particles shows that the core part is highly ordered carbon, while the shell part is disordered carbon. We have found that the new-type carbon obtained from tumbling CVD has a uniform core (graphite)-shell (pyrolytic carbon) structure. The electrochemical property of the new-type carbons has been examined using a charge-discharge cycler. The coating of pyrolytic carbon on the surface of graphite can effectively reduce the initial irreversible capacity by 47.5%. Cyclability and rate-capability of theses carbons with the core-shell structure are much better than those of bare graphite. From electrochemical impedance spectroscopy (EIS) spectra, it is found that the coating of pyrolytic carbon on the surface of graphite causes the decrease of the contact resistance in the carbon electrodes, which means the formation of solid electrolyte interface (SEI) layer is suppressed. We suggest that coating of pyrolytic carbon by the tumbling CVD is an effective method in improving the electrochemical properties of graphite electrodes for lithium ion secondary batteries

Process for the fabrication of aluminum metallized pyrolytic graphite sputtering targets

Science.gov (United States)

Makowiecki, Daniel M.; Ramsey, Philip B.; Juntz, Robert S.

1995-01-01

An improved method for fabricating pyrolytic graphite sputtering targets with superior heat transfer ability, longer life, and maximum energy transmission. Anisotropic pyrolytic graphite is contoured and/or segmented to match the erosion profile of the sputter target and then oriented such that the graphite's high thermal conductivity planes are in maximum contact with a thermally conductive metal backing. The graphite contact surface is metallized, using high rate physical vapor deposition (HRPVD), with an aluminum coating and the thermally conductive metal backing is joined to the metallized graphite target by one of four low-temperature bonding methods; liquid-metal casting, powder metallurgy compaction, eutectic brazing, and laser welding.

Ellipsometric investigations of pyrolytically deposited thin indium oxide films

International Nuclear Information System (INIS)

Winkler, U.

1980-01-01

Ellipsometric measurements have been carried out of thin indium oxide films deposited pyrolytically on glass substrates. It was found that the roughness of the films affected the measuring results. Therefore, only after applying a two-layer model a reasonable interpretation of the measuring results became possible

Nanomechanical Pyrolytic Carbon Resonators: Novel Fabrication Method and Characterization of Mechanical Properties

Directory of Open Access Journals (Sweden)

Maksymilian Kurek

2016-07-01

Full Text Available Micro- and nanomechanical string resonators, which essentially are highly stressed bridges, are of particular interest for micro- and nanomechanical sensing because they exhibit resonant behavior with exceptionally high quality factors. Here, we fabricated and characterized nanomechanical pyrolytic carbon resonators (strings and cantilevers obtained through pyrolysis of photoresist precursors. The developed fabrication process consists of only three processing steps: photolithography, dry etching and pyrolysis. Two different fabrication strategies with two different photoresists, namely SU-8 2005 (negative and AZ 5214e (positive, were compared. The resonant behavior of the pyrolytic resonators was characterized at room temperature and in high vacuum using a laser Doppler vibrometer. The experimental data was used to estimate the Young’s modulus of pyrolytic carbon and the tensile stress in the string resonators. The Young’s moduli were calculated to be 74 ± 8 GPa with SU-8 and 115 ± 8 GPa with AZ 5214e as the precursor. The tensile stress in the string resonators was 33 ± 7 MPa with AZ 5214e as the precursor. The string resonators displayed maximal quality factor values of up to 3000 for 525-µm-long structures.

Experimental investigation of linear thermal expansion of pyrolytic graphite at high temperatures

Science.gov (United States)

Senchenko, V. N.; Belikov, R. S.

2017-11-01

Using the previously described [1] experimental setup for investigation of the thermophysical properties of refractory materials under high pressure and temperature a few experiments with pyrolytic graphite were carried out. The density of the material was equal to 2.18 g/cm3. Experimental data on the linear thermal expansion in the perpendicular and parallel to the basal plane direction were obtained. Thermal expansion in the perpendicular to the basal plane direction during the heating from room temperature up to the melting point was 16.4 ± 1.6%. The results obtained allow calculating the density of pyrolytic graphite in the wide range of high temperatures up to the melting point.

Overliming detoxification of pyrolytic sugar syrup for direct fermentation of levoglucosan to ethanol.

Science.gov (United States)

Chi, Zhanyou; Rover, Marjorie; Jun, Erin; Deaton, Mark; Johnston, Patrick; Brown, Robert C; Wen, Zhiyou; Jarboe, Laura R

2013-12-01

The application of pyrolytic sugars for biofuel production through fermentation is challenged by inhibitory contaminant compounds. Inhibition is so severe that only 0.25% sugar syrup can be used. In this study, overliming was tested as a simple detoxification method, using the Escherichia coli KO11+ lgk to directly convert levoglucosan into ethanol. After treatment with at least 14.8 g/L of Ca(OH)2, fermentation with 2% (w/v) pyrolytic sugar syrup was observed with no inhibition of ethanol production. Further investigation of treatment time and temperature showed that 8-16 h of treatment at 20°C, and 1-4 h of treatment at 60°C are necessary to obtain consistent ethanol production. The samples treated with 18.5 g/L Ca(OH)2 at 60°C for 4 h showed no inhibition at 2.5%. Multiple contaminants removed by the overliming treatment were identified. This study demonstrates that overliming is a promising method for detoxification of pyrolytic sugars for fermentation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Low-temperature preparation of pyrolytic carbon

International Nuclear Information System (INIS)

Kidd, R.W.; Seifert, D.A.; Browning, M.F.

1984-01-01

Previous studies have demonstrated that nuclear waste forms coated with chemical vapor deposited pyrolytic carbon (PyC) at about 1273 K can provide ground water leach protection. To minimize the release during coating of volatile material from the waste forms and permit the coating of waste forms with a low softening point, a study was initiated to develop parameters for the catalytic deposition of PyC at low temperatures. The parameters surveyed in a fluidized-bed coater were deposition temperatures, carbon precursors, catalyst, diluent gas, concentration, and pressure

Oxidative desulfurization of tire pyrolysis oil

Directory of Open Access Journals (Sweden)

Ahmad Shahzad

2016-01-01

Full Text Available This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure and 50°C temperature for comparison of performance of various additives. The use of hydrogen peroxide-acetic acid mixture (10 wt.% was found more economical and effective in desulfurization and improvement of fuel properties of sample oils. The contribution of sulfuric acid in desulfurization and decreasing viscosity was also satisfactory but due to high price of concentrated sulfuric acid its use may not be economical. Calcium oxide and Fuller’s earth was not found to be effective in desulfurization. Results indicate that oxidative desulfurization could render tire pyrolysis oils suitable for blending as heating fuel.

Study of composite MWCNT/pyrolytic Cr interface by NEXAFS spectroscopy

International Nuclear Information System (INIS)

Petrova, O V; Nekipelov, S V; Mingaleva, A E; Sivkov, V N; Obiedkov, A M; Kaverin, B S; Kremlev, K V; Ketkov, S Yu; Gusev, S A; Vyalikh, D V; Molodtsov, S L

2016-01-01

A composite material based on MWCNT covered by pyrolytic Cr has been prepared by MOCVD growth technique using bis(arene)chromium compounds as the pyrolytic Cr source. Their structures and morphologies were preliminary studied by X-ray diffraction and scanning and scanning electron microscopy. The atomic and chemical composition of the interface, MWCNT surface and Cr-coating of the composite were studied by total electron yield mode in the range NEXAFS C1s - and Cr2p - absorption edge with use of synchrotron radiation of RGBL at BESSY-II. The study has shown that top layers of the MWCNT in composite have no essential destruction, the coating of the MWCNT surfaces is continuous and consists of Cr 2 O 3 . The chromium oxide adhesion is provided by chemical binding between the carbon atoms of the MWCNT top layer and the oxygen atoms of the coating. (paper)

Shale oil. II. Gases from oil shale

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil shale (from Colorado) was pyrolyzed, and the gaseous products obtained were studied. The organic material present in oil shale contains carboxyl groups that lose carbon dioxide during pyrolysis before the formation of soluble bitumen. Nitrogen was evolved as ammonia in two stages and was not continuous. The first evolution was from loosely combined nitrogen structures, whereas the second was from more stable forms. No hydrocarbons were present as such in the kerogen. The gaseous products from oil-shale pyrolysis were similar to those obtained by distillation of colophony, amber, coal, and wood. This places the kerogen of the oil shale in the same series of carbonaceous substances as those from which coals are formed. Kerogen appeared to be decomposed in three steps; namely, to insoluble bitumen, to soluble bitumen, and to oil (gas evolution accompanied each step). Its low solubility and the character of its pyrolytic gas indicated that kerogen is largely a resinous residue from vegetation of the past era and may have been formed by the tranportation of coal-forming organic debris to inland salty lakes or carried to the sea by clay-laden waters. The salt water and the natural settling action precipitated the clay and organic matter in an almost homogeneous deposit. Oil shales have existed to the present time because they have not been subjected to high pressures or elevated temperatures that would have changed them to petroleum.

Fungicidal values of bio-oils and their lignin-rich fractions obtained from wood/bark fast pyrolysis.

Science.gov (United States)

Mohan, Dinesh; Shi, Jenny; Nicholas, Darrel D; Pittman, Charles U; Steele, Philip H; Cooper, Jerome E

2008-03-01

Pine wood, pine bark, oak wood and oak bark were pyrolyzed in an auger reactor. A total of 16 bio-oils or pyrolytic oils were generated at different temperatures and residence times. Two additional pine bio-oils were produced at the National Renewable Energy Laboratory in a fluidized-bed reactor at different temperatures. All these bio-oils were fractionated to obtain lignin-rich fractions which consist mainly of phenols and neutrals. The pyrolytic lignin-rich fractions were obtained by liquid-liquid extraction. Whole bio-oils and their lignin-rich fractions were studied as potential environmentally benign wood preservatives to replace metal-based CCA and copper systems that have raised environmental concerns. Each bio-oil and several lignin-rich fractions were tested for antifungal properties. Soil block tests were conducted using one brown-rot fungus (Gloeophyllum trabeum) and one white-rot fungus (Trametes versicolor). The lignin-rich fractions showed greater fungal inhibition than whole bio-oils for a impregnation solution 10% concentration level. Water repellence tests were also performed to study wood wafer swelling behavior before and after bio-oil and lignin-rich fraction treatments. In this case, bio-oil fractions did not exhibit higher water repellency than whole bio-oils. Comparison of raw bio-oils in soil block tests, with unleached wafers, at 10% and 25% bio-oil impregnation solution concentration levels showed excellent wood preservation properties at the 25% level. The good performance of raw bio-oils at higher loading levels suggests that fractionation to generate lignin-rich fractions is unnecessary. At this more effective 25% loading level in general, the raw bio-oils performed similarly. Prevention of leaching is critically important for both raw bio-oils and their fractions to provide decay resistance. Initial tests of a polymerization chemical to prevent leaching showed some success.

Bio-compatibility of the surface layer of pyrolytic graphite

Czech Academy of Sciences Publication Activity Database

Starý, V.; Bačáková, Lucie; Horník, J.; Chmelík, V.

2003-01-01

Roč. 433, 1-2 (2003), s. 191-198 ISSN 0040-6090 R&D Projects: GA ČR GA106/99/0626; GA MŠk OC 527.130 Institutional research plan: CEZ:AV0Z5011922; CEZ:MSM 210000012 Keywords : carbon-carbon composite * pyrolytic graphite * cell adhesion Subject RIV: JI - Composite Materials Impact factor: 1.598, year: 2003

Cathode deposits in fullerene formation — microstructural evidence for independent pathways of pyrolytic carbon and nanobody formation

Science.gov (United States)

Taylor, G. H.; Gerald, J. D. Fitz; Pang, L.; Wilson, M. A.

1994-01-01

Microstructures in cathode deposits formed during fullerene production by electrical arcing in helium have been examined in detail. This has provided new information about the mechanisms by which nanobodies (nanotubes and nanoparticles) and pyrolytic carbon are deposited. Nanobodies and pyrolytic carbon form independently; the former probably grow in the plasma then deposit on the electrode but much of the latter deposits directly on the electrode surface.

Converting of oil shale and biomass into liquid hydrocarbons via pyrolysis

International Nuclear Information System (INIS)

Kılıç, Murat; Pütün, Ayşe Eren; Uzun, Başak Burcu; Pütün, Ersan

2014-01-01

Highlights: • Co-processing of oil shale with an arid land biomass for hydrocarbon production. • Co-pyrolysis in TGA and fixed-bed reactor. • Characterization of oil and char. - Abstract: In this study, co-pyrolytic behaviors of oil shale and Euphorbia rigida were investigated at different temperatures in a fixed bed reactor at 450, 500, and 550 °C with a heating rate of 10 °C/min in the presence of nitrogen atmosphere. The obtained solid product (char) and liquid product (tar) were analyzed by using different types of characterization techniques. Experimental results showed co-pyrolysis of oil shale and biomass could be an environmental friendly way for the transformation of these precursors into valuable products such as chemicals or fuels

London forces in highly oriented pyrolytic graphite

Directory of Open Access Journals (Sweden)

L.V. Poperenko

2017-07-01

Full Text Available Surface of highly oriented pyrolytic graphite with terrace steps was studied using scanning tunneling microscopy with high spatial resolution. Spots with positive and negative charges were found in the vicinity of the steps. Values of the charges depended both on the microscope needle scan velocity and on its motion direction. The observed effect was theoretically explained with account of London forces that arise between the needle tip and the graphite surface. In this scheme, a terrace step works as a nanoscale diode for surface electric currents.

Huge magnetoresistance effect of highly oriented pyrolytic graphite

International Nuclear Information System (INIS)

Du Youwei; Wang Zhiming; Ni Gang; Xing Dingyu; Xu Qingyu

2004-01-01

Graphite is a quasi-two-dimensional semimetal. However, for usual graphite the magnetoresistance is not so high due to its small crystal size and no preferred orientation. Huge positive magnetoresistance up to 85300% at 4.2 K and 4950% at 300 K under 8.15 T magnetic field was found in highly oriented pyrolytic graphite. The mechanism of huge positive magnetoresistance is not only due to ordinary magnetoresistance but also due to magnetic-field-driven semimetal-insulator transition

Mechanical performance of pyrolytic carbon in prosthetic heart valve applications.

Science.gov (United States)

Cao, H

1996-06-01

An experimental procedure has been developed for rigorous characterization of the fracture resistance and fatigue crack extension in pyrolytic carbon for prosthetic heart valve application. Experiments were conducted under sustained and cyclic loading in a simulated biological environment using Carbomedics Pyrolite carbon. While the material was shown to have modest fracture toughness, it exhibited excellent resistance to subcritical crack growth. The crack growth kinetics in pyrolytic carbon were formulated using a phenomenological description. A fatigue threshold was observed below which the crack growth rate diminishes. A damage tolerance concept based on fracture mechanics was used to develop an engineering design approach for mechanical heart valve prostheses. In particular, a new quantity, referred to as the safe-life index, was introduced to assess the design adequacy against subcritical crack growth in brittle materials. In addition, a weakest-link statistical description of the fracture strength is provided and used in the design of component proof-tests. It is shown that the structural reliability of mechanical heart valves can be assured by combining effective flaw detection and manufacturing quality control with adequate damage tolerance design.

Role of oxygen-containing functional groups in forest fire-generated and pyrolytic chars for immobilization of copper and nickel.

Science.gov (United States)

Esfandbod, Maryam; Merritt, Christopher R; Rashti, Mehran Rezaei; Singh, Balwant; Boyd, Sue E; Srivastava, Prashant; Brown, Christopher L; Butler, Orpheus M; Kookana, Rai S; Chen, Chengrong

2017-01-01

Char as a carbon-rich material, can be produced under pyrolytic conditions, wildfires or prescribed burn offs for fire management. The objective of this study was to elucidate mechanistic interactions of copper (Cu 2+ ) and nickel (Ni 2+ ) with different chars produced by pyrolysis (green waste, GW; blue-Mallee, BM) and forest fires (fresh-burnt by prescribed fire, FC; aged char produced by wild fire, AC). The pyrolytic chars were more effective sorbents of Cu 2+ (∼11 times) and Ni 2+ (∼5 times) compared with the forest fire chars. Both cross-polarization (CPMAS-NMR) and Bloch decay (BDMAS-NMR) 13 C NMR spectroscopies showed that forest fire chars have higher woody components (aromatic functional groups) and lower polar groups (e.g. O-alkyl C) compared with the pyrolytic chars. The polarity index was greater in the pyrolytic chars (0.99-1.34) than in the fire-generated chars (0.98-1.15), while aromaticity was lower in the former than in the latter. Fourier transform infrared (FTIR) and Raman spectroscopies indicated the binding of carbonate and phosphate with both Cu 2+ and Ni 2+ in all chars, but with a greater extent in pyrolytic than forest fire-generated chars. These findings have demonstrated the key role of char's oxygen-containing functional groups in determining their sorption capacity for the Cu 2+ and Ni 2+ in contaminated lands. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolytic sugars from cellulosic biomass

Science.gov (United States)

Kuzhiyil, Najeeb

phosphoric acids) and organic acids (formic and acetic acids) followed by analytical pyrolysis on a micropyrolyzer/GC/MS/FID system. It was found that sulfuric and phosphoric acids are very effective in passivating the AAEM thereby increasing the yield of anhydrosugars. An excellent correlation was discovered between the amount of acid required to obtain the maximum yield of anhydrosugars and the amount of AAEM contained in the biomass feedstock. In the micro-scale studies, up to 56% of the cellulose contained in the biomass was converted into anhydrosugars which is close to the 57% conversion obtained from pure cellulose pyrolysis. It is known that LG polymerization and subsequent charring occur at temperatures above 275°C depending on the vapor pressure of LG in the gas stream. A study of pyrolysis of acid-infused biomass feedstocks at various temperatures revealed that LG recovery is best at lower temperatures than the conventional pyrolysis temperature range of 450-500°C. Pyrolysis of acid-infused biomass failed in a continuous fluidized bed reactor due to clogging of the bed. The feedstock formed vitreous material along with the fluidizing sand that was formed from poor pyrolysis of lignin. However, more investigation of this phenomenon is a subject for future work. Pyrolysis experiments on an auger type reactor were successful in producing bio-oils with unprecedented amounts of sugars. Though there was increase in charring when compared to the control feedstock, pyrolysis of red oak infused with 0.4 wt% of sulfuric acid produced bio-oil with 18wt% of sugars. One of the four fractions of bio-oil collected contained most of the sugars, which shows significant potential for separating the sugars from bio-oil using simple means. This work points towards a new pathway for making advanced biofuels viz. upgrading pyrolytic sugars from biomass that could compete with enzymatic sugars from biomass.

Pyrolytic oil of banana (Musa spp.) pseudo-stem via fast process

Energy Technology Data Exchange (ETDEWEB)

Abdullah, Nurhayati; Sulaiman, Fauziah; Taib, Rahmad Mohd [School of Physics, Universiti Sains Malaysia, 11800 USM Pulau Pinang (Malaysia); Miskam, Muhamad Azman [Science and Engineering Research Centre, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia)

2015-04-24

This study was an attempt to produce bio-oil from banana pseudo-stem, a waste of banana cultivation, using fast pyrolysis technology. The compositions were determined and the thermal degradation behaviour of the raw material was analyzed using Perkin-Elmer Simultaneous Thermal Analyzer (STA) 6000. A 300 g/h fluidized bed bench scale fast pyrolysis unit, assembled with double screw feeders and cyclones, operating at atmospheric pressure, was used to obtain the pyrolysis liquid. The study involves the impact of the following key variables; the reactor temperature in the range of 450–650 °C, and the residence time in the range of 1.00–3.00 s. The particle size was set at 224-400 µm. The properties of the liquid product were analyzed for calorific heating value, pH value, conductivity, water and char content. The basic functional groups of the compositions were also determined using FTIR. The properties of the liquid product were compared with other wood derived bio-oil. The pyrolysis liquids derived from banana pseudo-stem were found to be in an aqueous phase.

Catalytic Hydrogenation of Bio-Oil for Chemicals and Fuels

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.

2006-02-14

The scope of work includes optimizing processing conditions and demonstrating catalyst lifetime for catalyst formulations that are readily scaleable to commercial operations. We use a bench-scale, continuous-flow, packed-bed, catalytic, tubular reactor, which can be operated in the range of 100-400 mL/hr., from 50-400 C and up to 20MPa (see Figure 1). With this unit we produce upgraded bio-oil from whole bio-oil or useful bio-oil fractions, specifically pyrolytic lignin. The product oils are fractionated, for example by distillation, for recovery of chemical product streams. Other products from our tests have been used in further testing in petroleum refining technology at UOP and fractionation for product recovery in our own lab. Further scale-up of the technology is envisioned and we will carry out or support process design efforts with industrial partners, such as UOP.

Pyrolytic carbon coating for cytocompatibility of titanium oxide nanoparticles: a promising candidate for medical applications

International Nuclear Information System (INIS)

Behzadi, Shahed; Simchi, Abdolreza; Imani, Mohammad; Yousefi, Mohammad; Galinetto, Pietro; Amiri, Houshang; Stroeve, Pieter; Mahmoudi, Morteza

2012-01-01

Nanoparticles for biomedical use must be cytocompatible with the biological environment that they are exposed to. Current research has focused on the surface functionalization of nanoparticles by using proteins, polymers, thiols and other organic compounds. Here we show that inorganic nanoparticles such as titanium oxide can be coated by pyrolytic carbon (PyC) and that the coating has cytocompatible properties. Pyrolization and condensation of methane formed a thin layer of pyrolytic carbon on the titanium oxide core. The formation of the PyC shell retards coalescence and sintering of the ceramic phase. Our MTT assay shows that the PyC-coated particles are cytocompatible at employed doses. (paper)

Contribution to the study of hard, low-density pyrolytic carbons

International Nuclear Information System (INIS)

Boutin, F.R.

1966-06-01

Apparent contradictions in the properties of pyrolytic carbons obtained at 1600 deg C (hardness and graphitization) are studied. It is shown that structure of the deposit is turbostratic with high internal stresses (δ -2 ), and it graphitizes (by thermal treatment over 2000 deg C) in a similar manner to graphitisable carbon. Because the deposit forms lamellar compounds, it is presumed that the structure is similar to that of graphitisable carbon. Since it is not structure dependant, the hardness originates from the 'growth texture' and is not comparable with the hardness of a non-graphitisable carbon. The pyrolytic carbon studied is composed of regions, on the overage a few microns across, formed by the stacking of small carbon platelets, interlocked and showing a preferred orientation. The mis-orientation of the various regions produces general disorientation. We estimate that the introduction of the particles of some material such as thermal black which are observed in the electron microscope are responsible for the mis-orientation. The density and hardness of the deposit are a result of the interlocking of platelets, which creates a closed porosity and prevents any sliding of the atomic planes. (author) [fr

Decomposition mechanism of melamine borate in pyrolytic and thermo-oxidative conditions

Energy Technology Data Exchange (ETDEWEB)

Hoffendahl, Carmen; Duquesne, Sophie; Fontaine, Gaëlle; Bourbigot, Serge, E-mail: serge.bourbigot@ensc-lille.fr

2014-08-20

Highlights: • Decomposition of melamine borate in pyrolytic and thermo-oxidative conditions was investigated. • With increasing temperature, orthoboric acid forms boron oxide releasing water. • Melamine decomposes evolving melamine, ammonia and other fragments. • Boron oxide is transformed into boron nitride and boron nitride-oxide structures through presence of ammonia. - Abstract: Decomposition mechanism of melamine borate (MB) in pyrolytic and thermo-oxidative conditions is investigated in the condensed and gas phases using solid state NMR ({sup 13}C and {sup 11}B), X-ray photoelectron spectroscopy (XPS), pyrolysis-gas chromatography–mass spectrometry (py-GCMS) and thermogravimetric analysis coupled with a Fourier transform infrared spectrometer (TGA–FTIR). It is evidenced that orthoboric acid dehydrates to metaboric and then to boron oxide. The melamine is partially sublimated. At the same time, melamine condensates, i.e., melem and melon are formed. Melon is only formed in thermo-oxidative conditions. At higher temperature, melem and melon decompose releasing ammonia which reacts with the boron oxide to form boron nitride (BN) and BNO structures.

Understanding the Behavior of the Oligomeric Fractions During Pyrolysis Oils Upgrading

Science.gov (United States)

Stankovikj, Filip

Fast pyrolysis oils represent most viable renewable sources for production of fuels and chemicals, and they could supplement significant portion of the depleting fossil fuels in near future. Progress on their utilization is impeded by their thermal and storage instability, lack of understanding of their complex composition and behavior during upgrading, including the poorly described water soluble fraction (WS). This work offers two new methodologies for simplified, and sensible description of the pyrolysis oils in terms of functional groups and chemical macro-families, augments our understanding of the composition of the WS, and the behavior of the heavy non-volatile fraction during pyrolysis oils stabilization. The concept of analyzing the volatile and non-volatile fraction in terms of functional groups has been introduced, and the quantification power of spectroscopic techniques (FTIR, 1H-NMR, UV fluorescence) for phenols, carbonyl and carboxyl groups was shown. The FT-ICR-MS van Krevelen diagram revealed the importance of dehydration reactions in pyrolysis oils and the presence of "pyrolytic humins" was hypothesized. For the first time the WS was analyzed with plethora of analytical techniques. This lead to proposition of a new characterization scheme based on functional groups, describing 90-100 wt.% of the bio-oils. The structure of idealized "pyrolytic humin" was further described as a random combination of 3-8 units of dehydrated sugars, coniferyl-type phenols, furans, and carboxylic acids attached on a 2,5-dioxo-6-hydroxyhexanal (DHH) backbone rich in carbonyl groups. TG-FTIR studies resulted in defining rules for fitting pyrolysis oils' DTG curves and assignment of TG residue. This second method is reliable for estimation of water content, light volatiles, WS and WIS. Finally, stabilization of two oils was analyzed through the prism of functional groups. Carbonyl and hydroxyl groups interconverted. The first attempt to follow silent 31P-NMR oxygen was

Influence of pyrolytic temperature on uranium adsorption capability by biochar derived from macauba coconut residue

Energy Technology Data Exchange (ETDEWEB)

Guilhen, Sabine Neusatz; Fungaro, Denise Alves [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Coleti, Jorge; Tenório, Jorge Alberto Soares, E-mail: snguilhen@ipen.br, E-mail: dfungaro@ipen.br, E-mail: jorgecoleti@usp.br, E-mail: jtenorio@usp.br [Universidade de São Paulo (USP), São Paulo, SP (Brazil). Departamento de Engenharia Metalúrgica e de Materiais

2017-07-01

Biochar (BC) is a carbon-rich product obtained when biomass is thermally decomposed at relatively low temperatures (under 700°C) and limited supply of oxygen in a process called pyrolysis. The conversion of biomass into BC can not only result in renewable energy source of synthetic gas and bio-oil, but also decrease the content of CO{sub 2} in the atmosphere, as well as improving soil fertility. Because of its porous structure, charged surface and surface functional groups, BC exhibits a great potential as an adsorbent. Brazilian agro energy chain involves tons of biomass waste, providing a wide range of biomass with different chemical and physical properties. BC characteristics strongly depend on the feedstock and the pyrolysis conditions, in which the temperature is the key parameter. The aim of this study was to evaluate the adsorption potential for the removal of uranium, U(VI), from aqueous solutions using BC obtained through the pyrolysis of the Macauba (Acrocomia aculeata) coconut endocarp as a function of the final pyrolytic temperature. BCs produced at higher temperatures are likely to present lower H/C and O/C ratios, indicating the loss of easily degradable carbon compounds such as volatile matter. In contrast, low-temperature pyrolysis produces not only a higher BC yield, but also richer in surface functional groups which will likely enable interactions with the U(VI) ions. The endocarp was subjected to six different pyrolytic temperatures, ranging from 250°C to 750 °C. The influence of parameters such as pH, sorbent dose and initial concentration on the adsorption of U(VI) was investigated. The maximum adsorption capacity (q) was achieved for the BC obtained at 250°C (BC250), which presented a removal percentage of approx. 86%, demonstrating the potential of the BC from macauba endocarp for treatment of wastewaters. Thus, submitting the endocarp to temperatures higher than 250°C becomes unnecessary, saving time and reducing operating costs

Influence of pyrolytic temperature on uranium adsorption capability by biochar derived from macauba coconut residue

International Nuclear Information System (INIS)

Guilhen, Sabine Neusatz; Fungaro, Denise Alves; Coleti, Jorge; Tenório, Jorge Alberto Soares

2017-01-01

Biochar (BC) is a carbon-rich product obtained when biomass is thermally decomposed at relatively low temperatures (under 700°C) and limited supply of oxygen in a process called pyrolysis. The conversion of biomass into BC can not only result in renewable energy source of synthetic gas and bio-oil, but also decrease the content of CO 2 in the atmosphere, as well as improving soil fertility. Because of its porous structure, charged surface and surface functional groups, BC exhibits a great potential as an adsorbent. Brazilian agro energy chain involves tons of biomass waste, providing a wide range of biomass with different chemical and physical properties. BC characteristics strongly depend on the feedstock and the pyrolysis conditions, in which the temperature is the key parameter. The aim of this study was to evaluate the adsorption potential for the removal of uranium, U(VI), from aqueous solutions using BC obtained through the pyrolysis of the Macauba (Acrocomia aculeata) coconut endocarp as a function of the final pyrolytic temperature. BCs produced at higher temperatures are likely to present lower H/C and O/C ratios, indicating the loss of easily degradable carbon compounds such as volatile matter. In contrast, low-temperature pyrolysis produces not only a higher BC yield, but also richer in surface functional groups which will likely enable interactions with the U(VI) ions. The endocarp was subjected to six different pyrolytic temperatures, ranging from 250°C to 750 °C. The influence of parameters such as pH, sorbent dose and initial concentration on the adsorption of U(VI) was investigated. The maximum adsorption capacity (q) was achieved for the BC obtained at 250°C (BC250), which presented a removal percentage of approx. 86%, demonstrating the potential of the BC from macauba endocarp for treatment of wastewaters. Thus, submitting the endocarp to temperatures higher than 250°C becomes unnecessary, saving time and reducing operating costs. (author)

A pseudo-curved oriented pyrolytic graphite neutron monochromator

International Nuclear Information System (INIS)

Ettedgui, H.; Gurewitz, E.; Pinto, H.

1979-03-01

A pseudo-curved neutron monochromator with a continuously variable curvature was constructed with four flat pieces of oriented pyrolytic graphite (OPG). Curvatures which yield maximum diffracted intensities were determined for neutrons of wavelengths 1 A and 2.4 A. The increase of the intensity relatively to that of a flat monochromator is by a factor of 2 and 1.5, for 1 A and 2.4 A, respectively. The neutron flux at three positions along the neutron path was determined by gold foils activation and compared with the flux from flat monochromators of OPG and copper

Mesoscopic self-organization of a self-assembled supramolecular rectangle on highly oriented pyrolytic graphite and Au(111) surfaces.

Science.gov (United States)

Gong, Jian-Ru; Wan, Li-Jun; Yuan, Qun-Hui; Bai, Chun-Li; Jude, Hershel; Stang, Peter J

2005-01-25

A self-assembled supramolecular metallacyclic rectangle was investigated with scanning tunneling microscopy on highly oriented pyrolytic graphite and Au(111) surfaces. The rectangles spontaneously adsorb on both surfaces and self-organize into well ordered adlayers. On highly oriented pyrolytic graphite, the long edge of the rectangle stands on the surface, forming a 2D molecular network. In contrast, the face of the rectangle lays flat on the Au(111) surface, forming linear chains. The structures and intramolecular features obtained through high-resolution scanning tunneling microscopy imaging are discussed.

CVD mechanism of pyrolytic boron nitride

International Nuclear Information System (INIS)

Tanji, H.; Monden, K.; Ide, M.

1987-01-01

Pyrolytic boron nitride (P-BN) has become a essential material for III-V compound semiconductor manufacturing process. As the demand from electronics industry for larger single crystals increases, the demand for larger and more economical P-BN components is growing rapidly. P-BN is manufactured by low pressure CVD using boron-trihalides and ammonia as the reactants. In spite that P-BN has been in the market for quite a long time, limited number of fundamental studies regarding the kinetics and the formation mechanism of P-BN have been reported. As it has been demonstrated in CVD of Si, knowledge and both theoretical and empirical modeling of CVD process can be applied to improve the deposition technology and to give more uniform deposition with higher efficiency, and it should also apply to the deposition of P-BN

Nitrite electrochemical sensor based on prussian blue/single-walled carbon nanotubes modified pyrolytic graphite electrode

CSIR Research Space (South Africa)

Adekunle, AS

2011-09-01

Full Text Available Nitrite, NO2- (in neutral), and NO (in acidic media) were used as analytical probe to investigate the electrocatalytic properties of Prussian blue nanoparticles (PB) modified edge plane pyrolytic graphite (EPPG) electrode. Results indicate...

Pyrolytic carbon membranes containing silica: morphological approach on gas transport behavior

Science.gov (United States)

Park, Ho Bum; Lee, Sun Yong; Lee, Young Moo

2005-04-01

Pyrolytic carbon membrane containing silica (C-SiO 2) is a new-class material for gas separation, and in the present work we will deal with it in view of the morphological changes arising from the difference in the molecular structure of the polymeric precursors. The silica embedded carbon membranes were fabricated by a predetermined pyrolysis step using imide-siloxane copolymers (PISs) that was synthesized from benzophenone tetracarboxylic dianhydrides (BTDA), 4,4'-oxydianiline (ODA), and amine-terminated polydimethylsiloxane (PDMS). To induce different morphologies at the same chemical composition, the copolymers were prepared using one-step (preferentially a random segmented copolymer) sand two-step polymerization (a block segmented copolymer) methods. The polymeric precursors and their pyrolytic C-SiO 2 membranes were analyzed using thermal analysis, atomic force microscopy, and transmission electron microscopy, etc. It was found that the C-SiO 2 membrane derived from the random PIS copolymer showed a micro-structure containing small well-dispersed silica domains, whereas the C-SiO 2 membrane from the block PIS copolymer exhibited a micro-structure containing large silica domains in the continuous carbon matrix. Eventually, the gas transport through these C-SiO 2 membranes was significantly affected by the morphological changes of the polymeric precursors.

Electron-impact and pyrolytic eliminations from 4-tert-butylcyclohexyl xanthates

International Nuclear Information System (INIS)

Eadon, G.; Jefson, M.

1976-01-01

The stereochemistry of electron--impact induced xanthic acid elimination reactions was assessed by mass spectrographic studies of cis and trans deuterated 4-tert-butylcyclohexyl xanthates and their derivatives. Cis elimination was observed to be about 30 times as facile as trans elimination in the axial xanthate reaction. In the equatorial ester derivative reactions, the cis elimination was found to be slightly preferred. The electron-impact induced elimination results were compared with pyrolytic elimination results for the xanthates; and similar stereochemistry was observed for each type of elimination

Pyrolytic conversion of plastic and rubber waste to hydrocarbons with basic salt catalysts

Science.gov (United States)

Wingfield, Jr., Robert C.; Braslaw, Jacob; Gealer, Roy L.

1985-01-01

The invention relates to a process for improving the pyrolytic conversion of waste selected from rubber and plastic to low molecular weight olefinic materials by employing basis salt catalysts in the waste mixture. The salts comprise alkali or alkaline earth compounds, particularly sodium carbonate, in an amount of greater than about 1 weight percent based on the waste feed.

Quantitative investigation of free radicals in bio-oil and their potential role in condensed-phase polymerization.

Science.gov (United States)

Kim, Kwang Ho; Bai, Xianglan; Cady, Sarah; Gable, Preston; Brown, Robert C

2015-03-01

We report on the quantitative analysis of free radicals in bio-oils produced from pyrolysis of cellulose, organosolv lignin, and corn stover by EPR spectroscopy. Also, we investigated their potential role in condensed-phase polymerization. Bio-oils produced from lignin and cellulose show clear evidence of homolytic cleavage reactions during pyrolysis that produce free radicals. The concentration of free radicals in lignin bio-oil was 7.5×10(20)  spin g(-1), which was 375 and 138 times higher than free-radical concentrations in bio-oil from cellulose and corn stover. Pyrolytic lignin had the highest concentration in free radicals, which could be a combination of carbon-centered (benzyl radicals) and oxygen-centered (phenoxy radicals) organic species because they are delocalized in a π system. Free-radical concentrations did not change during accelerated aging tests despite increases in molecular weight of bio-oils, suggesting that free radicals in condensed bio-oils are stable. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrotreatment of pyrolysis oils from biomass. Reactivity of the various categories of oxygenated compounds and preliminary techno-economical study

Energy Technology Data Exchange (ETDEWEB)

Grange, P.; Laurent, E.; Maggi, R.; Centeno, A.; Delmon, B. [Unite de Catalyse et Chimie des Materiaux Divises, Universite Catholique de Louvain, Louvain-la-Neuve (Belgium)

1996-05-31

This paper describes essential aspects of the hydrotreatment of pyrolytic oils in the light of results obtained until now at the Universite Catholique de Louvain. Stability of pyrolysis oils necessitates a two-step processing. A low temperature hydrotreatment enables stabilization through reactions like olefin, carbonyl and carboxylic groups reduction. Further hydrotreatment aims at hydrodeoxygenation of phenols and hydrocracking of larger molecules. Results about catalysts, reaction conditions and parameters enabling or influencing the control of the reaction are summarized. Based on these laboratory data, a preliminary techno-economical evaluation is made. 50 wt.-% yields in hydrocarbons for deep hydrorefining of pyrolysis oils can be expected. Nevertheless, a moderate hydroconversion with partial elimination of oxygen would be, economically, more advantageous

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends.

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-01-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L.; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-04-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325 °C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Directory of Open Access Journals (Sweden)

Lucía Botella

2018-04-01

Full Text Available The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons, middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here.

Bio-Oil Hydrotreatment for Enhancing Solubility in Biodiesel and the Oxydation Stability of Resulting Blends

Science.gov (United States)

Botella, Lucía; Stankovikj, Filip; Sánchez, José L.; Gonzalo, Alberto; Arauzo, Jesús; Garcia-Pérez, Manuel

2018-01-01

The major challenge for the pyrolytic conversion of lignocellulosic materials into crude bio-oil is the poor quality of the final product. Several strategies (addition of solvents, production of emulsions, and extraction with biodiesel) have been studied to improve its fuel properties. The extraction with biodiesel is an interesting solution because it allows direct utilization of some bio-oil fractions as fuels. However, fraction extracted with biodiesel is typically between 10 and 18 wt. %. In this paper we studied mild hydrotreatment of pyrolysis oil to enhance its solubility in biodiesel. The study was conducted with BTG and Amaron oils hydrotreated at temperatures between 200 and 325°C in the presence of Ru/C catalyst. Hydrotreated oils generated three phases: top oil (light hydrocarbons), middle aqueous phase and bottom heavy oil phase. Each of the phases was characterized and the content of acetic acid, phenols, aromatic compounds, and linear alkane hydrocarbons quantified. The upgraded bio-oils were more soluble in biodiesel than the crude bio-oils, obtaining blends with up to 48 and 38 wt. % for the BTG and Amaron bio-oil, respectively. Some of the fuel properties of the resulting blends are also reported here. PMID:29675406

The waste-to-energy framework for integrated multi-waste utilization: Waste cooking oil, waste lubricating oil, and waste plastics

Energy Technology Data Exchange (ETDEWEB)

Singhabhandhu, Ampaitepin; Tezuka, Tetsuo [Energy Economics Laboratory, Department of Socio-Environmental Energy Science, Graduate School of Energy Science, Kyoto University, Yoshida-honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

2010-06-15

Energy generation by wastes is considered one method of waste management that has the benefit of energy recovery. From the waste-to-energy point of view, waste cooking oil, waste lubricating oil, and waste plastics have been considered good candidates for feedstocks for energy conversion due to their high heating values. Compared to the independent management of these three wastes, the idea of co-processing them in integration is expected to gain more benefit. The economies of scale and the synergy of co-processing these wastes results in higher quality and higher yield of the end products. In this study, we use cost-benefit analysis to evaluate the integrated management scenario of collecting the three wastes and converting them to energy. We report the total heat of combustion of pyrolytic oil at the maximum and minimum conversion rates, and conduct a sensitivity analysis in which the parameters of an increase of the electricity cost for operating the process and increase of the feedstock transportation cost are tested. We evaluate the effects of economy of scale in the case of integrated waste management. We compare four cases of waste-to-energy conversion with the business as usual (BAU) scenario, and our results show that the integrated co-processing of waste cooking oil, waste lubricating oil, and waste plastics is the most profitable from the viewpoints of energy yield and economics. (author)

Alternative waste form development - low-temperature pyrolytic carbon coatings

International Nuclear Information System (INIS)

Oma, K.H.; Rusin, J.M.; Kidd, R.W.; Browning, M.F.

1981-01-01

Although several chemical vapor deposition (CVD) - coated waste forms have been successfully produced, some major disadvantages associated with the high-temperature fluidized-bed CVD coating process exist. To overcome these disadvantages, the Pacific Northwest Laboratory has initiated the development of a pyrolytic carbon CVD coating system to coat large waste-form particles at temperatures ranging from 400 to 500/degree/C. This relatively simple system has been used to coat kilogram quantities of simulated waste-glass marbles. Further development of this system could result in a viable process to coat bulk quantities of both glass and ceramic waste forms. This paper discusses various aspects of the development work, including coating techniques, parametric study, and coater equipment. 10 refs

Reflectivity and filtering characteristics of pyrolytic graphite

International Nuclear Information System (INIS)

Adib, M.; Abdel-Kawy, A.; Ashry, A.; Abbas, Y.; Wahba, W.

1988-01-01

The neutron transmission measurements through oriented pyrolytic graphite (P.G. crystal) were carried out in the wavelength band from 0.15 nm to 6.5 nm at different orientations of the (002) plane of the crystal w.r.t. the neutron beam direction. It was found that the P.G. crystal may be tuned for optimum scattering of second-order neutrons in the wavelength ranging between 0.112 nm and 0.425 nm, by adjusting the filter in an appropriate orientation. The reflectivity of (002), (004) and (006) planes of P.G. were measured and the following results are obtained: the reflectivity of (002) plane was found to be 99% by (transmission method). The ratio of the integrated intensity of the reflected neutrons from (004) and (006) is 3.14+-0.25 and is found to be in agreement with the calculated ratio. The measurements were performed using the fixed scattering angle spectrometer installed in front of the ET-RR-1 reactor horizontal channel

Upgrading pyrolytic residue from waste tires to commercial carbon black.

Science.gov (United States)

Zhang, Xue; Li, Hengxiang; Cao, Qing; Jin, Li'e; Wang, Fumeng

2018-05-01

The managing and recycling of waste tires has become a worldwide environmental challenge. Among the different disposal methods for waste tires, pyrolysis is regarded as a promising route. How to effectively enhance the added value of pyrolytic residue (PR) from waste tires is a matter of great concern. In this study, the PRs were treated with hydrochloric and hydrofluoric acids in turn under ultrasonic waves. The removal efficiency for the ash and sulfur was investigated. The pyrolytic carbon black (PCB) obtained after treating PR with acids was analyzed by X-ray fluorescence spectrophotometry, Fourier transform infrared spectrometry, X-ray diffractometry, laser Raman spectrometry, scanning electron microscopy, thermogravimetric (TG) analysis, and physisorption apparatus. The properties of PCB were compared with those of commercial carbon black (CCB) N326 and N339. Results showed PRs from waste tires were mainly composed of carbon, sulfur, and ash. The carbon in PCB was mainly from the CCB added during tire manufacture rather than from the pyrolysis of pure rubbers. The removal percentages for the ash and sulfur of PR are 98.33% (from 13.98 wt % down to 0.24 wt %) and 70.16% (from 1.81 wt % down to 0.54 wt %), respectively, in the entire process. The ash was mainly composed of metal oxides, sulfides, and silica. The surface properties, porosity, and morphology of the PCB were all close to those of N326. Therefore, PCB will be a potential alternative of N326 and reused in tire manufacture. This route successfully upgrades PR from waste tires to the high value-added CCB and greatly increases the overall efficiency of the waste tire pyrolysis industry.

Characteristics of hydrogen evolution and oxidation catalyzed by Desulfovibrio caledoniensis biofilm on pyrolytic graphite electrode

International Nuclear Information System (INIS)

Yu Lin; Duan Jizhou; Zhao Wei; Huang Yanliang; Hou Baorong

2011-01-01

Highlights: → The sulphate-reducing bacteria (SRB) have the ability to catalyze the hydrogen evolution and oxidation on pyrolytic graphite electrode. → The SRB biofilm decreases the overpotential and electron transfer resistance by the CV and EIS detection. → The SRB biofilm can transfer electrons to the 0.24 V polarized pyrolytic graphite electrode and the maximum current is 0.035 mA, which is attributed to SRB catalyzed hydrogen oxidation. → The SRB biofilm also can obtain electron from the -0.61 V polarized PGE to catalyze the hydrogen evolution. - Abstract: Hydrogenase, an important electroactive enzyme of sulphate-reducing bacteria (SRB), has been discovered having the capacity to connect its activity to solid electrodes by catalyzing hydrogen evolution and oxidation. However, little attention has been paid to similar electroactive characteristics of SRB. In this study, the electroactivities of pyrolytic graphite electrode (PGE) coated with SRB biofilm were investigated. Two corresponding redox peaks were observed by cyclic voltammetry detection, which were related to the hydrogen evolution and oxidation. Moreover, the overpotential for the reactions decreased by about 0.2 V in the presence of the SRB biofilm. When the PGE coated with the SRB biofilm was polarized at 0.24 V (vs. SHE), an oxidation current related to the hydrogen oxidation was found. The SRB biofilm was able to obtain electrons from the -0.61 V (vs. SHE) polarized PGE to form hydrogen, and the electron transfer resistance also decreased with the formation of SRB biofilm, as measured by the non-destructive electrochemical impendence spectroscopy detection. It was concluded that the hydrogen evolution and oxidation was an important way for the electron transfer between SRB biofilm and solid electrode in anaerobic environment.

Study of bio-oil and bio-char production from algae by slow pyrolysis

International Nuclear Information System (INIS)

Chaiwong, K.; Kiatsiriroat, T.; Vorayos, N.; Thararax, C.

2013-01-01

This study examined bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. A thermogravimetric analyser (TGA) was used to investigate the pyrolytic characteristics and essential components of algae. It was found that the temperature for the maximum degradation, 322 °C, is lower than that of other biomass. With our fixed-bed reactor, 125 g of dried Spirulina Sp. algae was fed under a nitrogen atmosphere until the temperature reached a set temperature between 450 and 600 °C. It was found that the suitable temperature to obtain bio-char and bio-oil were at approximately 500 and 550 °C respectively. The bio-oil components were identified by a gas chromatography/mass spectrometry (GC–MS). The saturated functional carbon of the bio-oil was in a range of heavy naphtha, kerosene and diesel oil. The energy consumption ratio (ECR) of bio-oil and bio-char was calculated, and the net energy output was positive. The ECR had an average value of 0.49. -- Highlights: •Bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. •Suitable temperature to obtained bio-oil and bio-char were at about 550 and 500 °C. •Saturated functional carbon of bio-oil was heavy naphtha, kerosene, diesel oil. •ECR had an average value of 0.49

Neutron transmission through pyrolytic graphite crystals

Energy Technology Data Exchange (ETDEWEB)

Adib, M. [Reactor Physics Department NRC, Reactor Physics Division, Nuclear Research Center, Egyptian Atomic Energy Authority, Cairo 13759 (Egypt); Habib, N. [Reactor Physics Department NRC, Reactor Physics Division, Nuclear Research Center, Egyptian Atomic Energy Authority, Cairo 13759 (Egypt)]. E-mail: nadiahabib15@yahoo.com; Fathaalla, M. [Reactor Physics Department NRC, Reactor Physics Division, Nuclear Research Center, Egyptian Atomic Energy Authority, Cairo 13759 (Egypt)

2006-05-15

Calculation of the total cross-section, neutron transmission and removal coefficient of pyrolytic graphite (PG) for thermal neutron energies were carried out using an additive formula. The formula takes into account the variation of thermal diffuse and Bragg scattering cross-sections in terms of PG temperature and mosaic spread for neutron energies in the range 1 meV to 1 eV. A computer code PG has been developed which allow calculations for the graphite in its hexagonal close-packed structure, when its c-direction is parallel with incident neutron beam (parallel orientation). The calculated total neutron cross-sections for PG in parallel orientation at different mosaic spreads were compared with the measured values. An overall agreement is indicated between the formula fits and experimental data at room and liquid nitrogen temperatures. A feasibility study for use of PG crystals as second-order neutron filter is detailed in terms of mosaic spread, optimum thickness and temperature. The calculated removal coefficients of PG crystals show that such crystals are high efficiency second-order filter within neutron energy intervals (4-7 meV) and (10-15 meV)

Mass spectrometric characterization of a pyrolytic radical source using femtosecond ionization

Energy Technology Data Exchange (ETDEWEB)

Frey, H M; Beaud, P; Mischler, B; Radi, P P; Tzannis, A P; Gerber, T [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-06-01

Radicals play, as reactive species, an important role in the chemistry of combustion. In contrast to atmospheric flames where spectra are congested due to high vibrational and rotational excitation, experiments in the cold environment of a molecular beam (MB) yield clean spectra that can be easily attributed to one species by Resonantly Enhanced Multi Photon Ionization (REMP). A pyrolytic radical source has been set up. To characterize the efficiency of the source `soft` ionization with femto second pulses is applied which results in less fragmentation, simplifying the interpretation of the mass spectrum. (author) figs., tabs., refs.

Identification and quantitation of anhydrosugars in biomass pyrolytic oils using carbon-13 NMR spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Castola, V.; Bighelli, A. [Universite de Corse, Equipe Chimie et Biomasse, Ajaccio (France); Conti, L.; Scano, G.; Mascia, S. [Universita di Sassari, Dipartimento di Chimica, Sassari (Italy); Casanova, J. [Universite de Corse, Equipe Chimie et Biomasse, Ajaccio (France)

2000-07-01

We described a method which allowed identification and quantitation of anhydrosugars in biomass pyrolysis liquids using carbon-13 NMR spectroscopy. The quantitative procedure was checked and validated (accuracy, precision and response linearity) with pure compounds and artificial mixtures. This method was then applied to the analysis of the glucidic fraction obtained after a simple and rapid fractionation of the bio oil. (author)

Structure-property relations for silicon nitride matrix composites reinforced with pyrolytic carbon pre-coated Hi-Nicalon fibers

NARCIS (Netherlands)

Kooi, B.J.; Hosson, J.Th.M. De; Olivier, C.; Veyret, J.B.

1999-01-01

Si3N4 matrix composites reinforced with pyrolytic carbon pre-coated Hi-Nicalon (SiC) fibers, were studied using tensile testing and transmission electron microscopy. Three types of samples were evaluated all with a nominal coating thickness of 200 nm. The composites were densified by hot pressing at

FAST PYROLYSIS – EFFECT OF WOOD DRYING ON THE YIELD AND PROPERTIES OF BIO-OIL

Directory of Open Access Journals (Sweden)

Eriks Samulis

2007-11-01

Full Text Available The composition and properties of the products of fast pyrolysis of hardwood, obtained in a two-chamber (drying and pyrolytic ablation type reactor in the temperature range 450-600ºС, were investigated. It has been found that, upon the additional drying of wood at 200ºС and subsequent pyrolysis, the quality of bio-oil is improved owing to the decrease in the amount of water and acids. It has been shown that the increase of the drying temperature to 240ºС decreases the yield of the main product. Optimum parameters of the drying conditions and the temperature of the pyrolysis of wood, at which the bio-oil yield exceeds 60% and its calorific value makes up 17-20 МJ/kg, have been determined.

Interaction of noble-metal fission products with pyrolytic silicon carbide

International Nuclear Information System (INIS)

Lauf, R.J.; Braski, D.N.

1982-01-01

Fuel particles for the High-Temperature Gas-Cooled Reactor (HTGR) contain layers of pyrolytic carbon and silicon carbide, which act as a miniature pressure vessel and form the primary fission product barrier. Of the many fission products formed during irradiation, the noble metals are of particular interest because they interact significantly with the SiC layer and their concentrations are somewhat higher in the low-enriched uranium fuels currently under consideration. To study fission product-SiC interactions, particles of UO 2 or UC 2 are doped with fission product elements before coating and are then held in a thermal gradient up to several thousand hours. Examination of the SiC coatings by TEM-AEM after annealing shows that silver behaves differently from the palladium group

Combination of electrospray ionization, atmospheric pressure photoionization and laser desorption ionization Fourier transform ion cyclotronic resonance mass spectrometry for the investigation of complex mixtures – Application to the petroleomic analysis of bio-oils

Energy Technology Data Exchange (ETDEWEB)

Hertzog, Jasmine [LCP-A2MC, FR 2843 Institut Jean Barriol de Chimie et Physique Moléculaires et Biomoléculaires, FR 3624 Réseau National de Spectrométrie de Masse FT-ICR à très haut champ, Université de Lorraine, ICPM, 1 boulevard Arago, 57078 Metz Cedex 03 (France); Carré, Vincent, E-mail: vincent.carre@univ-lorraine.fr [LCP-A2MC, FR 2843 Institut Jean Barriol de Chimie et Physique Moléculaires et Biomoléculaires, FR 3624 Réseau National de Spectrométrie de Masse FT-ICR à très haut champ, Université de Lorraine, ICPM, 1 boulevard Arago, 57078 Metz Cedex 03 (France); Le Brech, Yann [LRGP, CNRS, Université de Lorraine, ENSIC, 1, Rue Grandville, 54000 Nancy (France); Mackay, Colin Logan [SIRCAMS, School of Chemistry, University of Edinburgh, Edinburgh, EH9 3FJ, Scotland (United Kingdom); Dufour, Anthony [LRGP, CNRS, Université de Lorraine, ENSIC, 1, Rue Grandville, 54000 Nancy (France); Mašek, Ondřej [UK Biochar Research Center, School of Geosciences, University of Edinburgh, Kings Buildings, Edinburgh, EH9 3JN (United Kingdom); and others

2017-05-29

The comprehensive description of complex mixtures such as bio-oils is required to understand and improve the different processes involved during biological, environmental or industrial operation. In this context, we have to consider how different ionization sources can improve a non-targeted approach. Thus, the Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) has been coupled to electrospray ionization (ESI), laser desorption ionization (LDI) and atmospheric pressure photoionization (APPI) to characterize an oak pyrolysis bio-oil. Close to 90% of the all 4500 compound formulae has been attributed to C{sub x}H{sub y}O{sub z} with similar oxygen class compound distribution. Nevertheless, their relative abundance in respect with their double bound equivalent (DBE) value has evidenced significant differences depending on the ion source used. ESI has allowed compounds with low DBE but more oxygen atoms to be ionized. APPI has demonstrated the efficient ionization of less polar compounds (high DBE values and less oxygen atoms). The LDI behavior of bio-oils has been considered intermediate in terms of DBE and oxygen amounts but it has also been demonstrated that a significant part of the features are specifically detected by this ionization method. Thus, the complementarity of three different ionization sources has been successfully demonstrated for the exhaustive characterization by petroleomic approach of a complex mixture. - Highlights: • Non-targeted mass spectrometry by combining electrospray ionization, atmospheric pressure photoionization and laser/desorption ionization. • Exhaustive description of pyrolytic bio-oil components. • Distinction of sugaric derivatives, lignin derivatives and lipids contained in a woody-based pyrolytic bio-oil.

Model-free pyrolysis kinetics of sunflower seed and its de-oiled cake

International Nuclear Information System (INIS)

Özsin, Gamzenur; Kilic, Murat; Pütün, Ersan; Pütün, Ayşe E.

2015-01-01

Sunflower seed wastes from oil production are a potential biomass source for bio- energy production due to extensive and excessive oil production from sunflower seeds. Considering global energy requirement, pyrolysis seems a promising route for utilisation of such industrial biomass wastes. To develop, scale-up and operate pyrolysis plants efficiently, a fundamental understanding of pyrolysis behaviour and kinetics is essential. In this study, sunflower seeds and their waste cakes after extraction were evaluated as a potential biomass feedstock in pyrolysis process. In order to enlighten pyrolytic degradation behaviours, samples were pyrolysed under dynamic conditions from room temperature to 1000 °C using multiple heating rates. The main degradation regimes of the structures were characterized by high weight loss rates. Reaction kinetics was investigated with respect to conversion degree. It is anticipated that this study will be beneficial in optimizing the thermochemical processes, which may be utilize industrial biomass wastes. (full text)

Absence of field anisotropy in the intrinsic ferromagnetic signals of highly oriented pyrolytic graphite

International Nuclear Information System (INIS)

Ballestar, A.; Setzer, A.; Esquinazi, P.; Garcia, N.

2011-01-01

We have measured the magnetization of bulk samples of highly oriented pyrolytic graphite (HOPG) at magnetic fields applied parallel and perpendicular to the graphene layers. Within experimental error the intrinsic ferromagnetic signals of the samples show similar magnetic moments at saturation for the two magnetic field directions, in contrast to recently published data (J. Cervenka et al., Nat. Phys. 5 (2009) 840). To check that the SQUID device provides correctly the small ferromagnetic signals obtained after subtracting the 100 times larger diamagnetic background, we have prepared a sample with a superconducting Pb-film deposited on one of the HOPG surfaces. We show that the field dependence of the measured magnetic moment and after the background subtraction is highly reliable even in the sub-μ emu range providing the real magnetic properties of the embedded small ferromagnetic and superconducting signals. - Research Highlights: → We have measured the magnetization of bulk samples of highly oriented pyrolytic graphite (HOPG) at magnetic fields applied parallel and perpendicular to the graphene layers.→ Within experimental error the intrinsic ferromagnetic signals of the samples show similar magnetic moments at saturation for the two magnetic field directions.→ The absence of magnetic anisotropy of the intrinsic ferromagnetic order found in HOPG samples contrasts recently published data by Cervenka et al., Nat Phys 5, 840 (2009).

Pyrolytic Graphite as a Selective Neutron Filter

International Nuclear Information System (INIS)

Adib, M.; Habib, N.; Fathalla, M.

2006-01-01

The transmission of neutrons through pyrolytic graphite (PG) crystals, set at different angles with respect to incident beam, were calculated using an additive formula. A computer program HOPG was developed to provide the required calculation. An overall agreement between the calculated neutron transmissions through a slab of 1,85 mm thick PG crystal with an angular spread of c-axes of 0,4 degree, set at different angles to the incident beam, and the available experimental ones in the wavelength range from (0,02 to 1,4) nm were obtained. A feasibility study for use of PG crystal as an efficient second-order neutron filter is detailed in terms of crystal thickness, angular spread of c-axes and its operation with respect to the neutron beam. It was shown that a PG crystal with an angular spread of c-axes and its orientation with respect to the neutron beam. It was shown that a PG crystal with an angular spread of 0,8 degree is sufficient for optimum scattering of second-order neutrons in the wavelength band (0,384-0,183) nm, by adjusting the filter in an appropriate orientation

Deposition of pyrolytic carbon from C2H2--C3H6--Ar gas mixtures: coating under adiabatic conditions

International Nuclear Information System (INIS)

Gyarmati, E.; Gupta, A.K.; Puetter, B.

In this report a method is described by which pyrolytic carbon can be deposited from ethylene-propylene-argon gas mixtures at temperatures between 1230 and 1330 0 C in 55-mm fluidized bed apparatus without heat exchange with the apparatus

Field emission from the surface of highly ordered pyrolytic graphite

Energy Technology Data Exchange (ETDEWEB)

Knápek, Alexandr, E-mail: knapek@isibrno.cz [Institute of Scientific Instruments of the ASCR, v.v.i., Královopolská 147, Brno (Czech Republic); Sobola, Dinara; Tománek, Pavel [Department of Physics, FEEC, Brno University of Technology, Technická 8, Brno (Czech Republic); Pokorná, Zuzana; Urbánek, Michal [Institute of Scientific Instruments of the ASCR, v.v.i., Královopolská 147, Brno (Czech Republic)

2017-02-15

Highlights: • HOPG shreds were created and analyzed in the UHV conditions. • Current-voltage measurements have been done to confirm electron tunneling, based on the Fowler-Nordheim theory. • Surface was characterized by other surface evaluation methods, in particular by: SNOM, SEM and AFM. - Abstract: This paper deals with the electrical characterization of highly ordered pyrolytic graphite (HOPG) surface based on field emission of electrons. The effect of field emission occurs only at disrupted surface, i.e. surface containing ripped and warped shreds of the uppermost layers of graphite. These deformations provide the necessary field gradients which are required for measuring tunneling current caused by field electron emission. Results of the field emission measurements are correlated with other surface characterization methods such as scanning near-field optical microscopy (SNOM) or atomic force microscopy.

Field emission from the surface of highly ordered pyrolytic graphite

International Nuclear Information System (INIS)

Knápek, Alexandr; Sobola, Dinara; Tománek, Pavel; Pokorná, Zuzana; Urbánek, Michal

2017-01-01

Highlights: • HOPG shreds were created and analyzed in the UHV conditions. • Current-voltage measurements have been done to confirm electron tunneling, based on the Fowler-Nordheim theory. • Surface was characterized by other surface evaluation methods, in particular by: SNOM, SEM and AFM. - Abstract: This paper deals with the electrical characterization of highly ordered pyrolytic graphite (HOPG) surface based on field emission of electrons. The effect of field emission occurs only at disrupted surface, i.e. surface containing ripped and warped shreds of the uppermost layers of graphite. These deformations provide the necessary field gradients which are required for measuring tunneling current caused by field electron emission. Results of the field emission measurements are correlated with other surface characterization methods such as scanning near-field optical microscopy (SNOM) or atomic force microscopy.

Results of the International Energy Agency Round Robin on Fast Pyrolysis Bio-oil Production

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.; Meier, Dietrich; Oasmaa, Anja; van de Beld, Bert; Bridgwater, Anthony V.; Marklund, Magnus

2017-04-06

An international round robin study of the production of fast pyrolysis bio-oil was undertaken. Fifteen institutions in six countries contributed. Three biomass samples were distributed to the laboratories for processing in fast pyrolysis reactors. Samples of the bio-oil produced were transported to a central analytical laboratory for analysis. The round robin was focused on validating the pyrolysis community understanding of production of fast pyrolysis bio-oil by providing a common feedstock for bio-oil preparation. The round robin included: •distribution of 3 feedstock samples from a common source to each participating laboratory; •preparation of fast pyrolysis bio-oil in each laboratory with the 3 feedstocks provided; •return of the 3 bio-oil products (minimum 500 ml) with operational description to a central analytical laboratory for bio-oil property determination. The analyses of interest were: density, viscosity, dissolved water, filterable solids, CHN, S, trace element analysis, ash, total acid number, pyrolytic lignin, and accelerated aging of bio-oil. In addition, an effort was made to compare the bio-oil components to the products of analytical pyrolysis through GC/MS analysis. The results showed that clear differences can occur in fast pyrolysis bio-oil properties by applying different reactor technologies or configurations. The comparison to analytical pyrolysis method suggested that Py-GC/MS could serve as a rapid screening method for bio-oil composition when produced in fluid-bed reactors. Furthermore, hot vapor filtration generally resulted in the most favorable bio-oil product, with respect to water, solids, viscosity, and total acid number. These results can be helpful in understanding the variation in bio-oil production methods and their effects on bio-oil product composition.

Kinetic electron emission from highly oriented pyrolytic graphite surfaces induced by singly charged ions

CERN Document Server

Cernusca, S; Winter, H; Aumayr, F; Loerincik, J; Sroubek, Z

2002-01-01

We present total electron yields determined by current measurements for normal impact of H sup + , H sub 2 sup + , H sub 3 sup + , C sup + , N sup + and O sup + ions (E<=10 keV) on a clean highly oriented pyrolytic graphite surface. The kinetic energy of the projectiles has been varied from near threshold up to 10 keV. By comparing the results to similar data obtained for a polycrystalline Au surface the role of different target properties for kinetic electron emission can be analysed.

Erosion of pyrolytic graphite and Ti-doped graphite due to high flux irradiation

International Nuclear Information System (INIS)

Ohtsuka, Yusuke; Ohashi, Junpei; Ueda, Yoshio; Isobe, Michiro; Nishikawa, Masahiro

1997-01-01

The erosion of pyrolytic graphite and titanium doped graphite RG-Ti above 1,780 K was investigated by 5 keV Ar beam irradiation with the flux from 4x10 19 to 1x10 21 m -2 ·s -1 . The total erosion yields were significantly reduced with the flux. This reduction would be attributed to the reduction of RES (radiation enhanced sublimation) yield, which was observed in the case of isotropic graphite with the flux dependence of RES yield of φ -0.26 (φ: flux) obtained in our previous work. The yield of pyrolytic graphite was roughly 30% higher than that of isotropic graphite below the flux of 10 20 m -2 ·s -1 whereas each yield approached to very close value at the highest flux of 1x10 21 m -2 ·s -1 . This result indicated that the effect of graphite structure on the RES yield, which was apparent in the low flux region, would disappear in the high flux region probably due to the disordering of crystal structure. In the case of irradiation to RG-Ti at 1,780 K, the surface undulations evolved with a mean height of about 3 μm at 1.2x10 20 m -2 ·s -1 , while at higher flux of 8.0x10 20 m -2 ·s -1 they were unrecognizable. These phenomena can be explained by the reduction of RES of graphite parts excluding TiC grains. (author)

Study of nanometric thin pyrolytic carbon films for explosive electron emission cathode in high-voltage planar diode

Energy Technology Data Exchange (ETDEWEB)

Baryshevsky, Vladimir; Belous, Nikolai; Gurinovich, Alexandra; Gurnevich, Evgeny [Research Institute for Nuclear Problems, Belarusian State University, Bobruiskaya Str. 11, Minsk 220030 (Belarus); Kuzhir, Polina, E-mail: polina.kuzhir@gmail.com [Research Institute for Nuclear Problems, Belarusian State University, Bobruiskaya Str. 11, Minsk 220030 (Belarus); National Research Tomsk State University, 36 Lenin Prospekt, Tomsk 634050 (Russian Federation); Maksimenko, Sergey [Research Institute for Nuclear Problems, Belarusian State University, Bobruiskaya Str. 11, Minsk 220030 (Belarus); National Research Tomsk State University, 36 Lenin Prospekt, Tomsk 634050 (Russian Federation); Molchanov, Pavel; Shuba, Mikhail [Research Institute for Nuclear Problems, Belarusian State University, Bobruiskaya Str. 11, Minsk 220030 (Belarus); Roddatis, Vladimir [CIC energiGUNE, Albert Einstein 48, 01510 Minano, Alava (Spain); Institut für Materialphysik of Universität Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen (Germany); Kaplas, Tommi; Svirko, Yuri [Institute of Photonics, University of Eastern Finland, P.O. Box 111, Joensuu FI-80101 (Finland)

2015-04-30

We report on an experimental study of explosive electron emission properties of cathode made by nanometric thin pyrolytic carbon (PyC) films (2–150 nm) deposited on Cu substrate via methane-based chemical vapor deposition. High current density at level of 300 A/cm{sup 2} in 5 · 10{sup −5} Pa vacuum has been observed together with very stable explosive emission from the planar cathode. The Raman spectroscopy investigation proves that the PyC films remain the same after seven shots. According to the optical image analysis of the cathode before and after one and seven shots, we conclude that the most unusual and interesting feature of using the PyC films/Cu cathode for explosive emission is that the PyC layer on the top of the copper target prevents its evaporation and oxidation, which leads to higher emission stability compared to conventional graphitic/Cu cathodes, and therefore results in longer working life. - Highlights: • Explosive electron emission from pyrolytic carbon (PyC) cathode is reported. • We observe high current density, 300 A/cm{sup 2}, and stable emission parameters. • PyC integrity ensures a high application potential for high current electronics.

Pyrolysis of municipal plastic wastes for recovery of gasoline-range hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Demirbas, Ayhan [Department of Chemical Engineering, Selcuk University, Konya (Turkey)

2004-08-01

This paper describes non-catalytic pyrolysis of plastic waste materials. Three types of waste plastics were used in this study: polystyrene (PS), polyethylene (PE) and polypropylene (PP). Under pyrolysis conditions, plastic wastes can be decomposed into three fractions: gas, liquid and solid residue. The liquid products are usually composed of higher boiling point hydrocarbons. In order to obtain useful gasoline-range hydrocarbons from the pyrolytic oil, fractional distillation is preferred for product separation. More valuable chemical raw materials including benzene, toluene and other condensed aromatic hydrocarbons may be obtained by refining the pyrolytic oil. The results showed that waste PS yielded higher liquid, and waste PE and PP yielded higher gaseous products. The dominant pyrolytic liquid product of PS waste was styrene.

Prospective framework for collection and exploitation of waste cooking oil as feedstock for energy conversion

International Nuclear Information System (INIS)

Singhabhandhu, Ampaitepin; Tezuka, Tetsuo

2010-01-01

From the viewpoint of waste-to-energy, waste cooking oil is one of the attractive and available recycled feedstocks, apart from agricultural residues. The generation of energy from waste cooking oil is considered as an effective technique for waste management, as well as a beneficial form of energy recovery. Two alternative systems and a conventional system of waste cooking oil collection and conversion are evaluated by the cost benefit analysis in order to find a suitable method for waste-to-energy conversion. The results show that the collection of waste cooking oil with waste lubricating oil (System II) a useful alternative to the management of waste cooking oil (B/C > 1). The total heat produced by the combustion of pyrolytic oil at maximum and minimum conversion rates is also determined. The separate collection of waste cooking oil, subjected to chemical pre-treatment prior to introduction in a pyrolysis reactor (System III), is considered an undesirable option (B/C < 1) due to the cost of the chemicals involved. Although the exclusion of chemical pre-treatment makes System III a desirable option, the total amount of heat of combustion generated is less. The increased electricity cost required for the process has no effect on the benefit-cost ratio of System II. However, System III, excluding chemical pre-treatment, becomes an unprofitable alternative when the electricity cost reaches 100% of the fixed capital cost at the minimum conversion rate.

Atomic force microscopy study of anion intercalation into highly oriented pyrolytic graphite

Energy Technology Data Exchange (ETDEWEB)

Alliata, D; Haering, P; Haas, O; Koetz, R [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Siegenthaler, H [University of Berne (Switzerland)

1999-08-01

In the context of ion transfer batteries, we studied highly oriented pyrolytic graphite (HOPG) in perchloric acid, as a model to elucidate the mechanism of electrochemical intercalation in graphite. Aim of the work is the local and time dependent investigation of dimensional changes of the host material during electrochemical intercalation processes on the nanometer scale. We used atomic force microscopy (AFM), combined with cyclic voltammetry, as in-situ tool of analysis during intercalation and expulsion of perchloric anions into the HOPG electrodes. According to the AFM measurements, the HOPG interlayer spacing increases by 32% when perchloric anions intercalate, in agreement with the formation of stage IV of graphite intercalation compounds. (author) 3 figs., 3 refs.

On the fractography of overload, stress corrosion, and cyclic fatigue failures in pyrolytic-carbon materials used in prosthetic heart-valve devices.

Science.gov (United States)

Ritchie, R O; Dauskardt, R H; Pennisi, F J

1992-01-01

A scanning electron microscopy study is reported of the nature and morphology of fracture surfaces in pyrocarbons commonly used for the manufacture of mechanical heart-valve prostheses. Specifically, silicon-alloyed low-temperature-isotropic (LTI)-pyrolytic carbon is examined, both as a coating on graphite and as a monolithic material, following overload, stress corrosion (static fatigue), and cyclic fatigue failures in a simulated physiological environment of 37 degrees C Ringer's solution. It is found that, in contrast to most metallic materials yet in keeping with many ceramics, there are no distinct fracture morphologies in pyro-carbons which are characteristic of a specific mode of loading; fracture surfaces appear to be identical for both catastrophic and subcritical crack growth under either sustained or cyclic loading. We conclude that caution should be used in assigning the likely cause of failure of pyrolytic carbon heart-valve components using fractographic examination.

Cyclic fatigue and fracture in pyrolytic carbon-coated graphite mechanical heart-valve prostheses: role of small cracks in life prediction.

Science.gov (United States)

Dauskardt, R H; Ritchie, R O; Takemoto, J K; Brendzel, A M

1994-07-01

A fracture-mechanics based study has performed to characterize the fracture toughness and rates of cyclic fatigue-crack growth of incipient flaws in prosthetic heart-valve components made of pyrolytic carbon-coated graphite. Such data are required to predict the safe structural lifetime of mechanical heart-valve prostheses using damage-tolerant analysis. Unlike previous studies where fatigue-crack propagation data were obtained using through-thickness, long cracks (approximately 2-20 mm long), growing in conventional (e.g., compact-tension) samples, experiments were performed on physically small cracks (approximately 100-600 microns long), initiated on the surface of the pyrolytic-carbon coating to simulate reality. Small-crack toughness results were found to agree closely with those measured conventionally with long cracks. However, similar to well-known observations in metal fatigue, it was found that based on the usual computations of the applied (far-field) driving force in terms of the maximum stress intensity, Kmax, small fatigue cracks grew at rates that exceeded those of long cracks at the same applied stress intensity, and displayed a negative dependency on Kmax; moreover, they grew at applied stress intensities less than the fatigue threshold value, below which long cracks are presumed dormant. To resolve this apparent discrepancy, it is shown that long and small crack results can be normalized, provided growth rates are characterized in terms of the total (near-tip) stress intensity (incorporating, for example, the effect of residual stress); with this achieved, in principle, either form of data can be used for life prediction of implant devices. Inspection of the long and small crack results reveals extensive scatter inherent in both forms of growth-rate data for the pyrolytic-carbon material.

Design and Thermal Analysis for Irradiation of Pyrolytic Carbon/Silicon Carbide Diffusion Couples in the High Flux Isotope Reactor

Energy Technology Data Exchange (ETDEWEB)

Gerczak, Tyler J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Smith, Kurt R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Petrie, Christian M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

Tristructural-isotropic (TRISO)–coated particle fuel is a promising advanced fuel concept consisting of a spherical fuel kernel made of uranium oxide and uranium carbide, surrounded by a porous carbonaceous buffer layer and successive layers of dense inner pyrolytic carbon (IPyC), silicon carbide (SiC) deposited by chemical vapor , and dense outer pyrolytic carbon (OPyC). This fuel concept is being considered for advanced reactor applications such as high temperature gas-cooled reactors (HTGRs) and molten salt reactors (MSRs), as well as for accident-tolerant fuel for light water reactors (LWRs). Development and implementation of TRISO fuel for these reactor concepts support the US Department of Energy (DOE) Office of Nuclear Energy mission to promote safe, reliable nuclear energy that is sustainable and environmentally friendly. During operation, the SiC layer serves as the primary barrier to metallic fission products and actinides not retained in the kernel. It has been observed that certain fission products are released from TRISO fuel during operation, notably, Ag, Eu, and Sr [1]. Release of these radioisotopes causes safety and maintenance concerns.

Characterization of a polychromatic neutron beam diffracted by pyrolytic graphite crystals

CERN Document Server

Byun, S H; Choi, H D

2002-01-01

The beam spectrum for polychromatic neutrons diffracted by pyrolytic graphite crystals was characterized. The theoretical beam spectrum was obtained using the diffraction model for a mosaic crystal. The lattice vibration effects were included in the calculation using the reported vibration amplitude of the crystal and the measured time-of-flight spectra in the thermal region. The calculated beam spectrum was compared with the results obtained in the absence of thermal motion. The lattice vibration effects became more important for the higher diffraction orders and a large decrease in the neutron flux induced by the vibrations was identified in the epithermal region. The validity of the beam spectrum was estimated by comparing with the effective quantities determined from prompt gamma-ray measurements and Cd-ratios measured both for 1/nu and non-1/nu nuclides.

Characteristics of Pyrolytic Graphite as a Neutron Monochromator

International Nuclear Information System (INIS)

Adib, M.; Habib, N.; El-Mesiry, M.S.; Fathallah, M.

2011-01-01

Pyrolytic graphite (PG) has become nearly indispensable in neutron spectroscopy. Since the integrated reflectivity of the monochromatic neutrons from PG crystals cut along its c-axis is high within a wavelength band from 0.1 nm up to .65 nm. The monochromatic features of PG crystal is detailed in terms of the optimum mosaic spread, crystal thickness and reactor moderating temperature for efficient integrated neutron reflectivity within the wavelength band. A computer code Mono-PG has been developed to carry out the required calculations for the PG hexagonal close-packed structure. Calculation shows that, 2 mm thick of PG crystal having 0.30 FWHM on mosaic spread are the optimum parameters of PG crystal as a monochromator at selected neutron wavelength shorter than 2 nm. However, the integrated neutron intensity of 2nd and 3rd orders from thermal reactor flux is even higher than that of the 1st order one at neutron wavelengths longer than 2 nm. While, from cold reactor flux, integrated neutron intensity of the 1st order within the wavelength band from 0.25 up to 0.5 nm is higher than the 2nd and 3rd ones

Oil spill aftermath : temporal evaluation of hydrocarbon sources in Guanabara Bay, Brazil

International Nuclear Information System (INIS)

Meniconi, M.F.G.; Massone, C.G.; Scofield, A.L.; Junior, V.J.F.

2005-01-01

The sources of polycyclic aromatic hydrocarbons (PAH) in environmental ecosystems are both natural and anthropogenic. PAHs interact with different types of environmental compartments and are subject to processes that lead to geochemical fates such as physical-chemical transformation, biodegradation and photo-oxidation. This study examined the sources of PAHs in the estuarine sediment of Guanabara Bay, Brazil following an accidental oil spill from an oil refinery in January 2000. The main portion of the oil was carried by tidal currents and wind. It spread over the water and reached islands and shorelines at the north part of the bay. The objective of this study was to determine the likely sources of hydrocarbons in the bay where untreated municipal sewage and industrial wastes are also dumped. Sediment samples were collected using cores and dredges from the intertidal and subtidal regions of the bay, reflecting both affected and unaffected areas. This paper summarized the results of 16 EPA priority PAH and their alkylated homologues from 21 sediment samples collected in the bay 10 days after the oil spill, immediately after the clean up effort, and then 3 years later. The hydrocarbon source was determined using PAH ratios for the samples studied. The highest PAH concentration was observed in 2000 as a result of the petrogenic and pyrolytic contribution to the sediments. 38 refs., 3 tabs., 9 figs

Erosion of CFC, pyrolytic and boronated graphite under short pulsed laser irradiation

International Nuclear Information System (INIS)

Kraaij, G.J.; Bakker, J.; Stad, R.C.L. van der

1992-07-01

The effect of short pulsed laser irradiation of '0/3' ms and up to 10 MJ/m 2 on different types of carbon base materials is described. These materials are investigated as candidate protection materials for the Plasma Facing Components of NET/ITER. These materials are: carbon fibre composite graphite, pyrolytic graphite and boronated graphite. The volume of the laser induced craters was measured with an optical topographic scanner, and these data are evaluated with a simple model for the erosion. As a results, the enthalpy of ablation is estimated as 30±3 MJ/kg. A comparison is made with finite element numerical calculations, and the effect of lateral heat transfer is estimated using an analytical model. (author). 8 refs., 23 figs., 4 tabs

Small-angle neutron scattering and cyclic voltammetry study on electrochemically oxidized and reduced pyrolytic carbon

International Nuclear Information System (INIS)

Braun, A.; Kohlbrecher, J.; Baertsch, M.; Schnyder, B.; Koetz, R.; Haas, O.; Wokaun, A.

2004-01-01

The electrochemical double layer capacitance and internal surface area of a pyrolytic carbon material after electrochemical oxidation and subsequent reduction was studied with cyclic voltammetry and small-angle neutron scattering. Oxidation yields an enhanced internal surface area (activation), and subsequent reduction causes a decrease of this internal surface area. The change of the Porod constant, as obtained from small-angle neutron scattering, reveals that the decrease in internal surface area is not caused merely by a closing or narrowing of the pores, but by a partial collapse of the pore network

Pyrolytic Graphite as a Tunable Second order Neutron Filter

International Nuclear Information System (INIS)

Adib, M.

2009-01-01

A study has been carried out on the neutron transmission through pyrolytic graphite (PG) crystals in order to check its applicability as an efficient tunable second order neutron filter. The neutron transmission have been calculated as a function of neutron wavelengths in the range from 0.01 nm up to 0.7 nm at various PG mosaic spread, thickness and orientation of its c-axis with respect to the beam direction The Computer package Graphite has been used to provide the required calculation. It was shown that highly aligned (10 FWHM on mosaic spread) PG crystal ∼2 cm thick, may be tuned for optimum scattering of 2 second order neutrons within some favorable wavelength intervals in the range between 0.112 and 0.425 nm by adjusting the crystal in an appropriate orientation. .However, a less quality and thinner PG was found to almost eliminate 2 second order neutrons at only tuned values of wavelength corresponding to the poison of the triple intersection points of the curves (hkl) ± and (00l)

Influence of polystyrene addition to cellulose on chemical structure and properties of bio-oil obtained during pyrolysis

International Nuclear Information System (INIS)

Rutkowski, Piotr; Kubacki, Andrzej

2006-01-01

The cellulose (C), polystyrene (PS) and cellulose/polystyrene (C-PS) mixtures (3:1, 1:1, 1:3 w/w) were subjected to a pyrolysis process to produce bio-oil. The pyrolytic oil yield was in the range of 45.5-94.8 wt% depending on the composition of the sample. Pyrolysis of polystyrene gives the highest oil yield, whereas for cellulose, the yield of liquid products was the lowest. The basic physicochemical properties of oils are strongly influenced by the original material and do not change additively. The polystyrene addition to cellulose clearly improves the quality of the bio-oil, resulting in decreases in acid number, pour point and density. The change of color is not so distinct. The FT-IR analysis of the oils showed that the oxygen functionalities and hydrocarbons contents highly depend on the composition of the cellulose/polystyrene mixture. The fractionation of bio-oils by column chromatography using hexane and benzene was followed by GC-MS analyses. Different classes of organic compounds were identified, i.e., carboxylic acids, phenols, aldehydes, ketones, esters, ethers and unsaturated linear and cyclic hydrocarbons. The proportion of hydrocarbons increases with a decrease of the cellulose/polystyrene ratio. The obtained results indicate that during pyrolysis, not only does decomposition of cellulose and polystyrene occur, but also, reactions between products from C and PS take place. That was proved by the presence of compounds identified only in the bio-oils obtained from C-PS compositions

Preliminary organic geochemical investigation of the Kimmeridgian oil shales. [United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Williams, P F.V.; Douglas, A G

1980-01-01

The Kimmeridge oil shales have assumed renewed significance because of their role as the prime source-rock for North Sea oil, and because of the need to assess their potential as a possible future supply of shale oil. This paper presents the results of a preliminary investigation of selected Kimmeridge oil shales. The immature shales are rich in organic matter with a dominantly marine type II kerogen showing evidence of algal contributions and a general sparsity of land-derived, higher plant detritus. Column chromatographic and capillary column gas chromatographic examinations of bitumens, pyrolysates and pyrolysis gas chromatograms of kerogen isolates show a predominance of aromatics in the hydrocarbon fractions, with bitumen n-alkane gas chromatograms showing evidence of algal-derived organic matter with n-alkane maxima in the n-C/sub 17/ region. Possible contributions from lower land plants are indicated by a second n-alkane maximum at n-C/sub 23/, whilst higher land plant detritus makes only a limited contribution. Reflected light microscopic examination of the shales also shows a general sparsity of recognizable land-derived woody or herbaceous material. Shale oil compositions reflect their pyrolytic origin, with unsaturates forming a large part of the aliphatic hydrocarbon fraction, together with significant amounts of isoprenoid alkanes; organic sulphur compounds are also prominent in the hydrocarbon fractions. Finally, considerable amounts of sterane and pentacyclic triterpane hydrocarbons have been found in the bitumen aliphatic hydrocarbon fractions, their distributions allowing Blackstone samples to be differentiated from those of lower stratigraphic levels.

Coprocessing of biooils from biomass pyrolysis and bitumen from oil sands

Energy Technology Data Exchange (ETDEWEB)

Feng, M.; Daruwalla, S.; Daruwalla, D.D. [Southwest Research Inst., San Antonia, TX (United States). Dept. of Chemical Engineering

2009-07-01

Liquid biooils can be produced from the thermochemical treatment of biomass by pyrolysis. However, because of their poor volatility, high viscosity, coking, corrosiveness, and cold flow problems, biooils cannot be used directly as transportation fuel. Biooils can be upgraded into a liquid transportation fuel by hydrodeoxygenation with typical hydrotreating procedure with sulfided cobalt and molybdenum (CoMo) or nickel molybdenum (NiMo) as catalysts in the current oil refinery facilities. Coprocessing of biooils and bitumen from oil sand provides an opportunity to process the two feeds at the same time which can be achieved by injection of pyrolytic biooils and vacuum gas oil (VGO) from bitumen into a fluid catalytic cracking (FCC) unit if the acid number of the biooils is below 35. Typically the biooils are diluted to about 1.5 to 5 per cent in the VGO feed to be processed. For the blends of VGO and biooils, the biooils appear to facilitate the cracking of the VGO and shift yields toward light ends, lower light cycle oil. They also clarify slurry oil, which makes the process more cost effective. This paper briefly reviewed the typical methods for bitumen pretreatment and preliminary upgrading. The paper also discussed the current status of coprocessing of biooils and hydrocarbons, and suggested two possible processes for coprocessing bitumen with biooils and biopitches. The impact on the hydrodesulphurization process conversion of dibenzothiophenic compounds was also studied, showing no differences of the inhibiting effect between these molecules. 8 refs., 4 tabs., 6 figs.

Low temperature conversion of plastic waste into light hydrocarbons

International Nuclear Information System (INIS)

Shah, Sajid Hussain; Khan, Zahid Mahmood; Raja, Iftikhar Ahmad; Mahmood, Qaisar; Bhatti, Zulfiqar Ahmad; Khan, Jamil; Farooq, Ather; Rashid, Naim; Wu, Donglei

2010-01-01

Advance recycling through pyrolytic technology has the potential of being applied to the management of plastic waste (PW). For this purpose 1 l volume, energy efficient batch reactor was manufactured locally and tested for pyrolysis of waste plastic. The feedstock for reactor was 50 g waste polyethylene. The average yield of the pyrolytic oil, wax, pyrogas and char from pyrolysis of PW were 48.6, 40.7, 10.1 and 0.6%, respectively, at 275 deg. C with non-catalytic process. Using catalyst the average yields of pyrolytic oil, pyrogas, wax and residue (char) of 50 g of PW was 47.98, 35.43, 16.09 and 0.50%, respectively, at operating temperature of 250 deg. C. The designed reactor could work at low temperature in the absence of a catalyst to obtain similar products as for a catalytic process.

Contact Angle Hysteresis on Graphene Surfaces and Hysteresis-free Behavior on Oil-infused Graphite Surfaces

Energy Technology Data Exchange (ETDEWEB)

Wu, Cyuan-Jhang; Li, Yueh-Feng [Department of Chemical and Materials Engineering, National Central University, Jhongli 320, Taiwan (China); Woon, Wei-Yen [Department of Physics, National Central University, Jhongli 320, Taiwan (China); Sheng, Yu-Jane, E-mail: yjsheng@ntu.edu.tw [Department of Chemical Engineering, National Taiwan University, Taipei 106, Taiwan (China); Tsao, Heng-Kwong, E-mail: hktsao@cc.ncu.edu.tw [Department of Chemical and Materials Engineering, National Central University, Jhongli 320, Taiwan (China); Department of Physics, National Central University, Jhongli 320, Taiwan (China)

2016-11-01

Highlights: • Contact angle hysteresis(CAH) on four graphitic surfacesisinvestigated. • The hysteresis loopof water drops on the polished graphite sheetshowsparticularly small receding contact angle. • The significant CAH observed on CVD graphene and highly oriented pyrolytic graphite is attributed mainly to adhesion hysteresis. • An oil-infused surface of a graphite sheet is produced by imbibition of hexadecane into its porous structure. • The hysteresis-free property for water drops on such a surface is examined and quantitatively explained. - Abstract: Contact angle hysteresis (CAH) on graphitic surfaces, including chemical vapor deposition (CVD) graphene, reduced electrophoretic deposition (EPD) graphene, highly oriented pyrolytic graphite (HOPG), and polished graphite sheet, has been investigated. The hysteresis loops of water drops on the first three samples are similar but the receding contact angle is particularly small for the polished graphite sheet.The significant CAH observed on CVD graphene and HOPG associated with atom-scale roughness has to be attributed mainly to adhesion hysteresis (surface relaxation), instead of roughness or defects.The difference of the wetting behavior among those four graphitic samples has been further demonstrated by hexadecane drops. On the surface of HOPG or CVD graphene,the contact line expands continuously with time, indicating total wetting for which the contact angle does not exist and contact line pinning disappears. In contrast, on the surface of reduced EPD graphene, spontaneous spreading is halted by spikes on it and partial wetting with small contact angle (θ≈4°) is obtained. On the surface of polished graphite sheet, the superlipophilicity and porous structure are demonstrated by imbibition and capillary rise of hexadecane. Consequently, an oil-infused graphite surface can be fabricated and the ultralow CAH of water (∆θ≈2°) is achieved.

Using sewage sludge pyrolytic gas to modify titanium alloy to obtain high-performance anodes in bio-electrochemical systems

Science.gov (United States)

Gu, Yuan; Ying, Kang; Shen, Dongsheng; Huang, Lijie; Ying, Xianbin; Huang, Haoqian; Cheng, Kun; Chen, Jiazheng; Zhou, Yuyang; Chen, Ting; Feng, Huajun

2017-12-01

Titanium is under consideration as a potential stable bio-anode because of its high conductivity, suitable mechanical properties, and electrochemical inertness in the operating potential window of bio-electrochemical systems; however, its application is limited by its poor electron-transfer capacity with electroactive bacteria and weak ability to form biofilms on its hydrophobic surface. This study reports an effective and low-cost way to convert a hydrophobic titanium alloy surface into a hydrophilic surface that can be used as a bio-electrode with higher electron-transfer rates. Pyrolytic gas of sewage sludge is used to modify the titanium alloy. The current generation, anodic biofilm formation surface, and hydrophobicity are systematically investigated by comparing bare electrodes with three modified electrodes. Maximum current density (15.80 A/m2), achieved using a modified electrode, is 316-fold higher than that of the bare titanium alloy electrode (0.05 A/m2) and that achieved by titanium alloy electrodes modified by other methods (12.70 A/m2). The pyrolytic gas-modified titanium alloy electrode can be used as a high-performance and scalable bio-anode for bio-electrochemical systems because of its high electron-transfer rates, hydrophilic nature, and ability to achieve high current density.

Yield and nutrient composition of biochar produced from different feedstocks at varying pyrolytic temperatures

International Nuclear Information System (INIS)

Naeem, M.A.; Khalid, M.; Arshad, M.; Ahmad, R.

2014-01-01

Variation in pyrolytic temperatures and feedstocks affects the yield and nutrient composition of biochar. Selection of suitable feedstock and optimum pyrolytic temperature is crucial before using it for agricultural purposes. We compared biochars produced from two feedstocks (wheat straw and rice) at three temperatures (300, 400 and 500 degree C). Biochar yield decreased significantly (p<0.05) with increasing pyrolysis temperature, while ash contents were increased. The cation exchange capacity was significantly higher (119 cmolc kg/sup -1/) at temperature 400 degree C. The pH, electrical conductivity (EC) and carbon content of biochars increased significantly with increasing temperature and maximum pH (10.4) and EC (3.35 dS m/sup -1/) were observed in rice straw biochar (WSB) at 500 degree C and carbon content (662 g kg/sup -1/) in wheat straw biochar (RSB) at 500 degree C. Concentration of phosphorus (P) and potassium (K) increased significantly with increasing temperature, while of nitrogen (N) decreased. Overall, the maximum N (13.8 g kg/sup -1/at 300 degree C) and P (3.4 g kg/sup -1/at 500 degree C) concentrations were observed in WSB while, maximum K (48 g kg/sup -1/ at 500 degree C)in RSB. High pyrolysis temperature reduced AB-DTPA extractable nutrients (expect Mn). The highest AB-DTPA extractable nutrients such as P (113 mg kg/sup -1/) and Ca (1.07 g kg/sup -1/) were observed in WSB at 300 degree C while, K (18 g kg/sup -1/) and magnesium (Mg) (1.55 g kg/sup -1/) in RSB at 300 degree C. Selected feedstock and use of low pyrolysis temperature may produce nutrient-rich biochar, with high CEC and low pH and these could have positive effects on calcareous soils. (author)

Pyrolytic Carbon Nanosheets for Ultrafast and Ultrastable Sodium-Ion Storage.

Science.gov (United States)

Cho, Se Youn; Kang, Minjee; Choi, Jaewon; Lee, Min Eui; Yoon, Hyeon Ji; Kim, Hae Jin; Leal, Cecilia; Lee, Sungho; Jin, Hyoung-Joon; Yun, Young Soo

2018-04-01

Na-ion cointercalation in the graphite host structure in a glyme-based electrolyte represents a new possibility for using carbon-based materials (CMs) as anodes for Na-ion storage. However, local microstructures and nanoscale morphological features in CMs affect their electrochemical performances; they require intensive studies to achieve high levels of Na-ion storage performances. Here, pyrolytic carbon nanosheets (PCNs) composed of multitudinous graphitic nanocrystals are prepared from renewable bioresources by heating. In particular, PCN-2800 prepared by heating at 2800 °C has a distinctive sp 2 carbon bonding nature, crystalline domain size of ≈44.2 Å, and high electrical conductivity of ≈320 S cm -1 , presenting significantly high rate capability at 600 C (60 A g -1 ) and stable cycling behaviors over 40 000 cycles as an anode for Na-ion storage. The results of this study show the unusual graphitization behaviors of a char-type carbon precursor and exceptionally high rate and cycling performances of the resulting graphitic material, PCN-2800, even surpassing those of supercapacitors. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Pyrolytic characteristics of biomass acid hydrolysis residue rich in lignin.

Science.gov (United States)

Huang, Yanqin; Wei, Zhiguo; Yin, Xiuli; Wu, Chuangzhi

2012-01-01

Pyrolytic characteristics of acid hydrolysis residue (AHR) of corncob and pinewood (CAHR, WAHR) were investigated using a thermo-gravimetric analyzer (TGA) and a self-designed pyrolysis apparatus. Gasification reactivity of CAHR char was then examined using TGA and X-ray diffractometer. Result of TGA showed that thermal degradation curves of AHR descended smoothly along with temperature increasing from 150 °C to 850 °C, while a "sharp mass loss stage" for original biomass feedstock (OBF) was observed. Char yield from AHR (42.64-30.35 wt.%) was found to be much greater than that from OBF (26.4-19.15 wt.%). In addition, gasification reactivity of CAHR char was lower than that of corncob char, and there was big difference in micro-crystallite structure. It was also found that CAHR char reactivity decreased with pyrolysis temperature, but increased with pyrolysis heating rate and gasification temperature at 850-950 °C. Furthermore, CAHR char reactivity performed better under steam atmosphere than under CO2 atmosphere. Copyright © 2011 Elsevier Ltd. All rights reserved.

The pyrolytic decomposition of o-, m-, and p-terphenyls and other potential reactor coolants

Energy Technology Data Exchange (ETDEWEB)

Juppe, G.; Hannaert, H.; Biver, F.

1963-03-15

Experiments were made on the pyrolytic decomposition of o-, m-, and p- terphenyls and mixtures of terphenyls with diphenyl. The effects of competing reactions were also studied by initially adding hydrogen, methane, ethane, propane, and benzene. The results indicate that the disappearance of o-, m-, and p-terphenyl seems to follow formally a first order reaction mechanism. The relative stability of the pure individual components increases in the order: oterphenyl (least stable), p-terphenyl, m-terphenyl (most stable). The activation energy was found to be in the neighborhood of 64 kcal/mole. The activation energy for the diphenyl formation during pyrolysis of an irradiated biphenyl-terphenyl mixture was found to be 47.9 kcal/mole. (P.C.H.)

Synthesis of gold nanoparticles on the surface of pyrolytic graphite using penicillin as a stabilizing reagent and the catalytic oxidation of α-naphthylamine

Science.gov (United States)

Song, Y. Z.; Song, Y.; Cheng, Z. P.; Zhou, J. F.; Wei, C.

2013-01-01

Electrochemical synthesis of gold nanoparticles on the surface of pyrolytic graphite using penicillin as a stabilizing reagent was proposed. The gold nanoparticles were characterized by scanning electron microscopy, cyclic voltammetry, IR spectra, UV spectra, and powder X-ray diffraction spectra. The electro-chemical catalysis of penicillin for α-naphthylamine was demonstrated.

Neutron transmission measurements of poly and pyrolytic graphite crystals

Science.gov (United States)

Adib, M.; Abbas, Y.; Abdel-Kawy, A.; Ashry, A.; Kilany, M.; Kenawy, M. A.

The total neutron cross-section measurements of polycrystalline graphite have been carried out in a neutron wavelength from 0.04 to 0.78 nm. This work also presents the neutron transmission measurements of pyrolytic graphite (PG) crystal in a neutron wavelength band from 0.03 to 0.50 nm, at different orientations of the PG crystal with regard to the beam direction. The measurements were performed using three time-of-flight (TOF) spectrometers installed in front of three of the ET-RR-1 reactor horizontal channels. The average value of the coherent scattering amplitude for polycrystalline graphite was calculated and found to be bcoh = (6.61 ± 0.07) fm. The behaviour of neutron transmission through the PG crystal, while oriented at different angles with regard to the beam direction, shows dips at neutron wavelengths corresponding to the reflections from (hkl) planes of hexagonal graphite structure. The positions of the observed dips are found to be in good agreement with the calculated ones. It was also found that a 40 mm thick PG crystal is quite enough to reduce the second-order contamination of the neutron beam from 2.81 to 0.04, assuming that the incident neutrons have a Maxwell distribution with neutron gas temperature 330 K.

Neutron transmission measurements of poly and pyrolytic graphite crystals

International Nuclear Information System (INIS)

Adib, M.; Abdel-Kawy, A.; Kilany, M.

1989-01-01

The total neutron cross-section measurements of polycrystalline graphite have been carried out in a neutron wavelength from 0.04 to 0.78 nm. This work also presents the neutron transmission measurements of pyrolytic graphite (PG) crystal in a neutron wavelength band from 0.03 to 0.50 nm, at different orientations of the PG crystal with regard to the beam direction. The measurements were performed using three time-of-flight (TOF) spectrometers installed in front of three of the ET-RR-1 reactor horizontal channels. The average value of the coherent scattering amplitude for polycrystalline graphite was calculated and found to be b coh = (6.61 ± 0.07) fm. The behaviour of neutron transmission through the PG crystal, while orientated at different angles with regard to the beam direction, shows dips at neutron wavelengths corresponding to the reflections from (hk1) planes of hexagonal graphite structure. The positions of the observed dips are found to be in good agreement with the calculated ones. It was also found that a 40 mm thick PG crystal is quite enough to reduce the second-order contamination of the neutron beam from 2.81 to 0.04, assuming that the incident neutrons have a Maxwell distribution with neutron gas temperature 330 K. (author)

Accelerator-Based Irradiation Creep of Pyrolytic Carbon Used in TRISO Fuel Particles for the (VHTR) Very High Temperature Reactors

International Nuclear Information System (INIS)

Wang, Lumin; Was, Gary

2010-01-01

Pyrolytic carbon (PyC) is one of the important structural materials in the TRISO fuel particles which will be used in the next generation of gas-cooled very-high-temperature reactors (VHTR). When the TRISO particles are under irradiation at high temperatures, creep of the PyC layers may cause radial cracking leading to catastrophic particle failure. Therefore, a fundamental understanding of the creep behavior of PyC during irradiation is required to predict the overall fuel performance.

Phase transitions to 120 GPa for shock-compressed pyrolytic and hot-pressed boron nitride

International Nuclear Information System (INIS)

Gust, W.H.; Young, D.A.

1977-01-01

Shock-compression characteristics of two types of hexagonal graphitelike boron nitride have been investigated. Highly oriented very pure pyrolytic boron nitride exhibits shock-velocity versus particle-velocity discontinuities that appear to be manifestations of the initiation of a sluggish phase transition. This transition begins at 20 GPa and is driven to completion (melting) at 75 GPa. Discontinuities in the plot for impure hot-pressed boron nitride indicate initiation at 10 GPa and completion at 20 GPa. The (U/sub s/, U/sub p/) plots follow essentially the same paths for 4.0 < U/sub p/ < 5.2 km/sec. No evidence for a transition to a metalliclike state was seen. Temperature calculations indicate that the material is liquid above approx.80 GPa

Sustainable pyrolytic sludge-char preparation on improvement of closed-loop sewage sludge treatment: Characterization and combined in-situ application.

Science.gov (United States)

Jin, Zhengyu; Chang, Fengmin; Meng, Fanlin; Wang, Cuiping; Meng, Yao; Liu, Xiaoji; Wu, Jing; Zuo, Jiane; Wang, Kaijun

2017-10-01

Aiming at closed-loop sustainable sewage sludge treatment, an optimal and economical pyrolytic temperature was found at 400-450 °C considering its pyrolysis efficiency of 65%, fast cracking of hydrocarbons, proteins and lipids and development of aromatized porous structure. Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) tests demonstrated the development of adsorptive functional groups and crystallographic phases of adsorptive minerals. The optimal sludge-char, with a medium specific surface area of 39.6 m 2  g -1 and an iodine number of 327 mgI 2 g -1 , performed low heavy metals lixiviation. The application of sludge-char in raw sewage could remove 30% of soluble chemical oxygen demand (SCOD), along with an acetic acid adsorption capacity of 18.0 mg g -1 . The developed mesopore and/or macropore structures, containing rich acidic and basic functional groups, led to good biofilm matrices for enhanced microbial activities and improved autotrophic nitrification in anoxic stage of an A/O reactor through adsorbed extra carbon source, and hence achieved the total nitrogen (TN) removal up to 50.3%. It is demonstrated that the closed-loop sewage sludge treatment that incorporates pyrolytic sludge-char into in-situ biological sewage treatment can be a promising sustainable strategy by further optimization. Copyright © 2017 Elsevier Ltd. All rights reserved.

The pyrolytic-plasma method and the device for the utilization of hazardous waste containing organic compounds

Energy Technology Data Exchange (ETDEWEB)

Opalińska, Teresa [Tele and Radio Research Institute, Ratuszowa 11, 03-450 Warsaw (Poland); Wnęk, Bartłomiej, E-mail: bartlomiej.wnek@itr.org.pl [Tele and Radio Research Institute, Ratuszowa 11, 03-450 Warsaw (Poland); Witowski, Artur; Juszczuk, Rafał; Majdak, Małgorzata [Tele and Radio Research Institute, Ratuszowa 11, 03-450 Warsaw (Poland); Bartusek, Stanilav [VŠB—Technical University of Ostrava, 17. listopadu 15/2172, 708 33 Ostrava − Poruba Czech Republic (Czech Republic)

2016-11-15

Highlights: • A first stage of the process of waste utilization consisted in pyrolysis of waste. • Then the pyrolytic gas was oxidized with a use of non-equilibrium plasma. • The device for the process implementation was built and characterized. • Correctness of the device operation was proven with a use of the decomposition of PE. • Usefulness of the method was proven in the process of utilization of EW. - Abstract: This paper is focused on the new method of waste processing. The waste, including hazardous waste, contain organic compounds. The method consists in two main processes: the pyrolysis of waste and the oxidation of the pyrolytic gas with a use of non-equilibrium plasma. The practical implementation of the method requires the design, construction and testing of the new device in large laboratory scale. The experiments were carried out for the two kinds of waste: polyethylene as a model waste and the electronic waste as a real waste. The process of polyethylene decomposition showed that the operation of the device is correct because 99.74% of carbon moles contained in the PE samples was detected in the gas after the process. Thus, the PE samples practically were pyrolyzed completely to hydrocarbons, which were completely oxidized in the plasma reactor. It turned out that the device is useful for decomposition of the electronic waste. The conditions in the plasma reactor during the oxidation process of the pyrolysis products did not promote the formation of PCDD/Fs despite the presence of the oxidizing conditions. An important parameter determining the efficiency of the oxidation of the pyrolysis products is gas temperature in the plasma reactor.

Biochar as porous media for thermally-induced non-catalytic transesterification to synthesize fatty acid ethyl esters from coconut oil

International Nuclear Information System (INIS)

Jung, Jong-Min; Lee, Jechan; Choi, Dongho; Oh, Jeong-Ik; Lee, Sang-Ryong; Kim, Jae-Kon; Kwon, Eilhann E.

2017-01-01

Highlights: • Biodiesel production using renewable resources. • Thermally-induced non-catalytic transesterification. • Synthesis of fatty acid ethyl esters without conventional catalysts. • Using biochar as porous medium in the non-catalytic transesterification. - Abstract: This study put great emphasis on evaluating biochar as porous media for the thermally-induced non-catalytic transesterification reaction to synthesize fatty acid ethyl esters (FAEE) from coconut oil. Thermogravimetric analysis (TGA) of coconut oil experimentally justified that the bond dissociation of fatty acid from the backbone of triglycerides (TGs) could be achieved, which finding could be applied to the non-catalytic transesterification reaction. To use biochar as porous medium, the surficial morphology of maize residue biochar (MRB) was characterized, revealing that biochar possessed the wider pore size distribution ranging from meso- to macro-pores than SiO 2 . The highest yield of FAEE from non-catalytic transesterification of coconut oil in the presence of MRB was 87% at 380 °C. To further enhance the FAEE yield, further studies associated with the production of FAEE with biochar made from different biomasses and various pyrolytic conditions should be performed.

Influence of Cu(NO32 initiation additive in two-stage mode conditions of coal pyrolytic decomposition

Directory of Open Access Journals (Sweden)

Larionov Kirill

2017-01-01

Full Text Available Two-stage process (pyrolysis and oxidation of brown coal sample with Cu(NO32 additive pyrolytic decomposition was studied. Additive was introduced by using capillary wetness impregnation method with 5% mass concentration. Sample reactivity was studied by thermogravimetric analysis with staged gaseous medium supply (argon and air at heating rate 10 °C/min and intermediate isothermal soaking. The initiative additive introduction was found to significantly reduce volatile release temperature and accelerate thermal decomposition of sample. Mass-spectral analysis results reveal that significant difference in process characteristics is connected to volatile matter release stage which is initiated by nitrous oxide produced during copper nitrate decomposition.

Pyrolytic and kinetic characteristics of the thermal decomposition of Perilla frutescens polysaccharide.

Directory of Open Access Journals (Sweden)

Quancheng Zhou

Full Text Available The thermal decomposition of Perilla frutescens polysaccharide was examined by thermogravimetry, differential thermogravimetry, and differential thermal analysis. The results showed that the mass loss of the substance proceeded in three steps. The first stage can be attributed to the expulsion of the water from ambient temperature to 182°C. The second stage corresponded to devolatilization from 182°C to 439°C. The residue slowly degraded in the third stage. The weight loss in air is faster than that in nitrogen, because the oxygen in air accelerated the pyrolytic reaction speed reaction. The heating rate significantly affected the pyrolysis of the sample. Similar activation energies of the degradation process (210-211 kJ mol⁻¹ were obtained by the FWO, KAS, and Popescu techniques. According to Popescu mechanism functions, the possible kinetic model was estimated to be Avrami-Erofeev 20 g(α = [-ln(1-α]⁴.

Polycyclic aromatic hydrocarbons (PAHs) and volatile organic compounds (VOCs) mitigation in the pyrolysis process of waste tires using CO₂ as a reaction medium.

Science.gov (United States)

Kwon, Eilhann E; Oh, Jeong-Ik; Kim, Ki-Hyun

2015-09-01

Our work reported the CO2-assisted mitigation of PAHs and VOCs in the thermo-chemical process (i.e., pyrolysis). To investigate the pyrolysis of used tires to recover energy and chemical products, the experiments were conducted using a laboratory-scale batch-type reactor. In particular, to examine the influence of the CO2 in pyrolysis of a tire, the pyrolytic products including C1-5-hydrocarbons (HCs), volatile organic carbons (VOCs), and polycyclic aromatic hydrocarbons (PAHs) were evaluated qualitatively by gas chromatography (GC) with mass spectroscopy (MS) as well as with a thermal conductivity detector (TCD). The mass balance of the pyrolytic products under various pyrolytic conditions was established on the basis of their weight fractions of the pyrolytic products. Our experimental work experimentally validated that the amount of gaseous pyrolytic products increased when using CO2 as a pyrolysis medium, while substantially altering the production of pyrolytic oil in absolute content (7.3-17.2%) and in relative composition (including PAHs and VOCs). Thus, the co-feeding of CO2 in the pyrolysis process can be considered an environmentally benign and energy efficient process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Selectively improving the bio-oil quality by catalytic fast pyrolysis of heavy-metal-polluted biomass: take copper (Cu) as an example.

Science.gov (United States)

Liu, Wu-Jun; Tian, Ke; Jiang, Hong; Zhang, Xue-Song; Ding, Hong-Sheng; Yu, Han-Qing

2012-07-17

Heavy-metal-polluted biomass derived from phytoremediation or biosorption is widespread and difficult to be disposed of. In this work, simultaneous conversion of the waste woody biomass into bio-oil and recovery of Cu in a fast pyrolysis reactor were investigated. The results show that Cu can effectively catalyze the thermo-decomposition of biomass. Both the yield and high heating value (HHV) of the Cu-polluted fir sawdust biomass (Cu-FSD) derived bio-oil are significantly improved compared with those of the fir sawdust (FSD) derived bio-oil. The results of UV-vis and (1)H NMR spectra of bio-oil indicate pyrolytic lignin is further decomposed into small-molecular aromatic compounds by the catalysis of Cu, which is in agreement with the GC-MS results that the fractions of C7-C10 compounds in the bio-oil significantly increase. Inductively coupled plasma-atomic emission spectrometry, X-ray diffraction, and X-ray photoelectron spectroscopy analyses of the migration and transformation of Cu in the fast pyrolysis process show that more than 91% of the total Cu in the Cu-FSD is enriched in the char in the form of zerovalent Cu with a face-centered cubic crystalline phase. This study gives insight into catalytic fast pyrolysis of heavy metals, and demonstrates the technical feasibility of an eco-friendly process for disposal of heavy-metal-polluted biomass.

Pyrolysis of rice husk over Zeolite based catalysts

International Nuclear Information System (INIS)

Bae, Yoon Ju; Kim, Jung Hwan; Cho, Hye Jung; Ko, Jeong Huy; Heo, Hyeon Su; Park, Hye Jin; Park, Young Kwon

2010-01-01

Full text: The utilization of biomass and other alternative fuel sources, rather than existing fossil fuels, would offer more environmentally acceptable processes for energy production and will aid in conserving the limited supplies of fossil fuels. Pyrolysis of biomass is one of the most promising tools to provide alternative energy sources. However, pyrolytic oils are not always completely volatile and contain high levels of oxygen, this being the major factor responsible for the high viscosity and corrosiveness. The upgrading of pyrolytic oils is a necessary process and involves the removal of oxygen by catalyst. In this study, various type of zeolites such as HZSM-5, HY, USY, Al-MCM-41; Al-SBA-15 etc. were applied. The upgraded oil was analyzed by GC-MS, GC, and elemental analysis etc. The results indicated that more stable oil was produced by transforming oxygen over various zeolite into H 2 O, CO and CO 2 . (author)

Chemical and Pyrolytic Thermogravimetric Characterization of Nigerian Bituminous Coals

Directory of Open Access Journals (Sweden)

Nyakuma Bemgba Bevan

2016-12-01

Full Text Available The discovery of new coal deposits in Nigeria presents solutions for nation’s energy crises and prospects for socioeconomic growth and sustainable development. Furthermore, the quest for sustainable energy to limit global warming, climate change, and environmental degradation has necessitated the exploration of alternatives using cleaner technologies such as coal pyrolysis. However, a lack of comprehensive data on physico-chemical and thermal properties of Nigerian coals has greatly limited their utilization. Therefore, the physico-chemical properties, rank (classification, and thermal decomposition profiles of two Nigerian bituminous coals – Afuze (AFZ and Shankodi-Jangwa (SKJ – were examined in this study. The results indicate that the coals contain high proportions of C, H, N, S, O and a sufficiently high heating value (HHV for energy conversion. The coal classification revealed that the Afuze (AFZ coal possesses a higher rank, maturity, and coal properties compared to the Shankodi-Jangwa (SKJ coal. A thermal analysis demonstrated that coal pyrolysis in both cases occurred in three stages; drying (30-200 °C, devolatilization (200-600 °C, and char decomposition (600-1000 °C. The results also indicated that pyrolysis at 1000 °C is not sufficient for complete pyrolysis. In general, the thermochemical and pyrolytic fuel properties indicate that the coal from both places can potentially be utilized for future clean energy applications.

DEPOSITION AND PROPERTIES OF A LITTLE-ORIENTED PYROLYTIC CARBON; Deposition et proprietes d'un carbone pyrolytique peu oriente

Energy Technology Data Exchange (ETDEWEB)

Rappeneau, J; Bocquet, M; Yvars, M; David, C; Auriol, A

1963-06-15

Pyrolytic carbon obtained by thermal decomposition of acetylene, at partial pressures of 0.02 to 0.1 atm, on walls heated to between 1550 and 1650 deg C, is characterized by its low density (1.35) and a not very marked preferred orientation of the crystallites. The latter property is expressed by an absence of laminar structure in the deposit and by its good compatibility with an artiticial graphite substrate. Following a description of the method of deposition and an outline of the structural properties, certain physical and chemical properties of the substance are examined. (auth)

Theoretical Study of the Kinetics of the Pyrolytic Elimination Reaction of Ethyl Chloride

Directory of Open Access Journals (Sweden)

Isaiah Ajibade Adejoro

2010-01-01

Full Text Available The products of the gas-phase elimination of ethyl chloride are hydrogen chloride and ethane. Using AM1, MNDO and PM3 Hamiltonians of quantum mechanical computer code called MOPAC, a procedure for the kinetics and computation of the Arrhenius parameters for the pyrolytic elimination reaction of ethyl chloride was devised in order to evaluate the predictive ability of the three Hamiltonians used. The first-order rate coefficient for the three Hamiltonians are 1.15x10-8s-1, 4.55x10-15s-1 and 5.36x10-4s-1 for AM1, MNDO and PM3 respectively. The results obtained showed that the rate constant for the computed Arrhenius parameters compare well with the experimental values in the literature, thus showing that the computational procedure adequately simulates experimental results; also the semi-empirical AMI calculation has the best predictive ability with experiment followed by PM3 while MNDO has the least.

Multiferroic BiFeO3 thin films and nanodots grown on highly oriented pyrolytic graphite substrates

Science.gov (United States)

Shin, Hyun Wook; Son, Jong Yeog

2017-12-01

Multiferroic BiFeO3 (BFO) thin films and nanodots are deposited on highly oriented pyrolytic graphite (HOPG) substrates via a pulsed laser deposition technique, where the HOPG surface has a honeycomb lattice structure made of carbon atoms, similar to graphene. A graphene/BFO/HOPG capacitor exhibited multiferroic properties, namely ferroelectricity (a residual polarization of 26.8 μC/cm2) and ferromagnetism (a residual magnetization of 1.1 × 10-5 emu). The BFO thin film had high domain wall energies and demonstrated switching time of approximately 82 ns. An 8-nm BFO nanodot showed a typical piezoelectric hysteresis loop with an effective residual piezoelectric constant of approximately 110 pm/V and exhibited two clearly separated current curves depending on the ferroelectric polarization direction.

Adsorption and manipulation of carbon onions on highly oriented pyrolytic graphite studied with atomic force microscopy

International Nuclear Information System (INIS)

Zhou Jianfeng; Shen Ziyong; Hou Shimin; Zhao Xingyu; Xue Zengquan; Shi Zujin; Gu Zhennan

2007-01-01

Carbon onions produced by DC arc discharge method were deposited on highly oriented pyrolytic graphite (HOPG) surface and their adsorption and manipulation was studied using an atomic force microscopy (AFM). Well-dispersed adsorption of carbon onions on HOPG surface was obtained and aggregations of onions were not observed. The van der Waals interaction between the onion and HOPG surface and that between two onions, were calculated and discussed using Hamaker's theory. The manipulation of adsorbed onions on HOPG surface was realized using the AFM in both the raster mode and the vector mode. The controllability and precision of two manipulation modes were compared and the vector mode manipulation was found superior, and is a useful technique for the construction of nano-scale devices based on carbon onions

Characterization of bio-oil from induction-heating pyrolysis of food-processing sewage sludges using chromatographic analysis.

Science.gov (United States)

Tsai, Wen-Tien; Lee, Mei-Kuei; Chang, Jeng-Hung; Su, Ting-Yi; Chang, Yuan-Ming

2009-05-01

In this study, gas chromatography-mass spectrometry (GC-MS) was used to analyze the pyrolytic bio-oils and gas fractions derived from the pyrolysis of industrial sewage sludges using induction-heating technique. The liquid products were obtained from the cryogenic condensation of the devolatilization fraction in a nitrogen atmosphere using a heating rate of 300 degrees C/min ranging from 25 to 500 degrees C. The analytical results showed that the pyrolysis bio-oils were very complex mixtures of organic compounds and contained a lot of nitrogenated and/or oxygenated compounds such as aliphatic hydrocarbons, phenols, pyridines, pyrroles, amines, ketones, and so on. These organic hydrocarbons containing nitrogen and/or oxygen should originate from the protein and nucleic acid textures of the microbial organisms present in the sewage sludge. The non-condensable devolatilization fractions were also composed of nitrogenated and oxygenated compounds, but contained small fractions of phenols, 1H-indoles, and fatty carboxylic acids. On the other hand, the compositions in the non-condensable gas products were principally carbon dioxide, carbon monoxide and methane analyzed by gas chromatography-thermal conductivity detector (GC-TCD).

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

International Nuclear Information System (INIS)

Babich, I.V.; Hulst, M. van der; Lefferts, L.; Moulijn, J.A.; O'Connor, P.; Seshan, K.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na 2 CO 3 ) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor and characterized for water content and heating value. The oil composition was analyzed by GC-MS. Pretreatment of chlorella with Na 2 CO 3 influences the primary conversion of chlorella by shifting the decomposition temperature to a lower value. In the presence of Na 2 CO 3 , gas yield increased and liquid yield decreased when compared with non-catalytic pyrolysis at the same temperatures. However, pyrolysis oil from catalytic runs carries higher heating value and lower acidity. Lower content of acids in the bio-oil, higher aromatics, combined with higher heating value show promise for production of high-quality bio-oil from algae via catalytic pyrolysis, resulting in energy recovery in bio-oil of 40%. -- Highlights: → The pyrolytic catalytic conversion of chlorella algae to liquid fuel precursor. → Na 2 CO 3 as a catalyst for the primary conversion of chlorella. → Pyrolysis oil from catalytic runs carries higher heating value and lower acidity. → High-quality bio-oil from algae via catalytic pyrolysis with energy recovery in bio-oil of 40%.

THE EFFECT OF APPLIED STRESS ON THE GRAPHITIZATION OF PYROLYTIC GRAPHITE

Energy Technology Data Exchange (ETDEWEB)

Bragg, R H; Crooks, D D; Fenn, Jr, R W; Hammond, M L

1963-06-15

Metallographic and x-ray diffraction studies were made of the effect of applied stress at high temperature on the structure of pyrolytic graphite (PG). The dominant factor was whether the PG was above or below its graphitization temperature, which, in turn, was not strongly dependent on applied stress. Below the graphitization temperature, the PG showed a high proportion of disordered layers (0.9), a fairly large mean tilt angle (20 deg ) and a small crystailite size (La --150 A). Fracture occurred at low stress and strain and the materiai exhibited a high apparent Young's modulus ( approximates 4 x 10/sup 6/ psi). Above the graphitization temperature, graphitization was considerably enhanced by strain up to about 8%. The disorder parameter was decreased from a zero strain value of 0.3 to 0.l5 with strain, the mean tilt angle was decreased to 4 deg , and a fivefold increase in crystallite size occurred. When the strainenhanced graphitization was complete, the material exhibited a low apparent modulus ( approximates 0.5 x 10/sup 6/ psi) and large plastic strains (>100%) for a constant stress ( approximates 55 ksi). Graphitization was shown to be a spontaneous process that is promoted by breaking cross-links thermally, and the process is furthered by chemical attack and plastic strain. (auth)

Cyclic fatigue-crack propagation, stress-corrosion, and fracture-toughness behavior in pyrolytic carbon-coated graphite for prosthetic heart valve applications.

Science.gov (United States)

Ritchie, R O; Dauskardt, R H; Yu, W K; Brendzel, A M

1990-02-01

Fracture-mechanics tests were performed to characterize the cyclic fatigue, stress-corrosion cracking, and fracture-toughness behavior of a pyrolytic carbon-coated graphite composite material used in the manufacture of cardiac valve prostheses. Testing was carried out using compact tension C(T) samples containing "atomically" sharp precracks, both in room-temperature air and principally in a simulated physiological environment of 37 degrees C Ringer's lactate solution. Under sustained (monotonic) loads, the composite exhibited resistance-curve behavior, with a fracture toughness (KIc) between 1.1 and 1.9 MPa square root of m, and subcritical stress-corrosion crack velocities (da/dt) which were a function of the stress intensity K raised to the 74th power (over the range approximately 10(-9) to over 10(-5) m/s). More importantly, contrary to common perception, under cyclic loading conditions the composite was found to display true (cyclic) fatigue failure in both environments; fatigue-crack growth rates (da/dN) were seen to be a function of the 19th power of the stress-intensity range delta K (over the range approximately 10(-11) to over 10(-8) m/cycle). As subcritical crack velocities under cyclic loading were found to be many orders of magnitude faster than those measured under equivalent monotonic loads and to occur at typically 45% lower stress-intensity levels, cyclic fatigue in pyrolytic carbon-coated graphite is reasoned to be a vital consideration in the design and life-prediction procedures of prosthetic devices manufactured from this material.

Removal of copper by oxygenated pyrolytic tire char: kinetics and mechanistic insights.

Science.gov (United States)

Quek, Augustine; Balasubramanian, Rajashekhar

2011-04-01

The kinetics of copper ion (Cu(II)) removal from aqueous solution by pyrolytic tire char was modeled using five different conventional models. A modification to these models was also developed through a modified equation that accounts for precipitation. Conventional first- and second-order reaction models did not fit the copper sorption kinetics well, indicating a lack of simple rate-order dependency on solute concentration. Instead, a reversible first-order rate reaction showed the best fit to the data, indicating a dependence on surface functional groups. Due to the varying solution pH during the sorption process, modified external and internal mass transfer models were employed. Results showed that the sorption of copper onto oxygenated chars was limited by external mass transfer and internal resistance with and without the modification. However, the modification of the sorption process produced very different results for unoxygenated chars, which showed neither internal nor external limitation to sorption. Instead, its slow sorption rate indicates a lack of surface functional groups. The sorption of Cu(II) by oxygenated and unoxygenated chars was also found to occur via three and two distinct stages, respectively. Copyright © 2010 Elsevier Inc. All rights reserved.

X-ray photoelectron spectroscopy study of pyrolytically coated graphite platforms submitted to simulated electrothermal atomic absorption spectrometry conditions

International Nuclear Information System (INIS)

Ruiz, Frine; Benzo, Zully; Quintal, Manuelita; Garaboto, Angel; Albornoz, Alberto; Brito, Joaquin L.

2006-01-01

The present work is part of an ongoing project aiming to a better understanding of the mechanisms of atomization on graphite furnace platforms used for electrothermal atomic absorption spectrometry (ETAAS). It reports the study of unused pyrolytic graphite coated platforms of commercial origin, as well as platforms thermally or thermo-chemically treated under simulated ETAAS analysis conditions. X-ray photoelectron spectroscopy (XPS) was employed to study the elements present at the surfaces of the platforms. New, unused platforms showed the presence of molybdenum, of unknown origin, in concentrations up to 1 at.%. Species in two different oxidations states (Mo 6+ and Mo 2+ ) were detected by analyzing the Mo 3d spectral region with high resolution XPS. The analysis of the C 1s region demonstrated the presence of several signals, one of these at 283.3 eV related to the presence of Mo carbide. The O 1s region showed also various peaks, including a signal that can be attributed to the presence of MoO 3 . Some carbon and oxygen signals were consistent with the presence of C=O and C-O- (probably C-OH) groups on the platforms surfaces. Upon thermal treatment up to 2900 deg. C, the intensity of the Mo signal decreased, but peaks due to Mo oxides (Mo 6+ and Mo 5+ ) and carbide (Mo 2+ ) were still apparent. Thermo-chemical treatment with 3 vol.% HCl solutions and heating up to 2900 deg. C resulted in further diminution of the Mo signal, with complete disappearance of Mo carbide species. Depth profiling of unused platforms by Ar + ion etching at increasing time periods demonstrated that, upon removal of several layers of carbonaceous material, the Mo signal disappears suggesting that this contamination is present only at the surface of the pyrolytic graphite platform

The optical constants and spectral specular reflectivity of highly oriented pyrolytic graphite (HOPG)

International Nuclear Information System (INIS)

Havstad, M.A.; Schildbach, M.A.; McLean, W. II.

1993-08-01

Measurements of the specular reflectivity and the optical constants of highly ordered pyrolytic graphite (HOPG) have been made using two independent optical systems. The first measures reflectance (at 1.06 μm and 293 K) by comparing the intensity of a laser beam before and after reflecting off the sample. The second determines the complex index of raft-action (from 0.55 to 8.45 μm, with sample temperatures of 293, 480, 900 and 1300 K) by ellipsometry. Agreement between the two methods is good. Moderate reflectivities are observed over the full spectral range of measurement: the spectral directional-hemispherical reflectivity at normal incidence varies from 0.41 at 0.55 μm to 0.74 at 8.45 μm. The components of the complex index of refraction increase smoothly with wavelength. The index of refraction increases from 3.10 at 0.55 μm to 7.84 at 8.45 μm. The extinction coefficient varies from 2.01 to 6.66 over the same range

A study on pyrolytic gasification of coffee grounds and implications to allothermal gasification

Energy Technology Data Exchange (ETDEWEB)

Masek, Ondrej; Konno, Miki; Hosokai, Sou; Sonoyama, Nozomu; Norinaga, Koyo; Hayashi, Jun-ichiro [Centre for Advanced Research of Energy Conversion Materials, Hokkaido University, N13-W8, Kita-ku, Sapporo 060-8628 (Japan)

2008-01-15

The increasing interest in biomass, as a renewable source of energy, is stimulating a search for suitable biomass resources as well as the development of technologies for their effective utilization. This work concentrated on characteristics of processes occurring during pyrolytic gasification of upgraded food industry residues, namely residue from industrial production of liquid coffee, and assessed its suitability for conversion in an allothermal gasifier. The influence of several operating parameters on product composition was examined with three different laboratory-scale reactors, studying the primary pyrolysis and secondary pyrolysis of nascent volatiles, and the steam gasification of char. The experimental results show that a high degree of conversion of UCG into volatiles and gases (up to 88% C-basis) can be achieved by fast pyrolysis even at temperatures as low as 1073 K. In addition, the degree of conversion is not influenced by the presence or concentration of steam, which is an important factor in allothermal gasification. Mathematical simulation of an allothermal gasifier showed that net cold-gas efficiency as high as 86% can be reached. (author)

A study on pyrolytic gasification of coffee grounds and implications to allothermal gasification

International Nuclear Information System (INIS)

Masek, Ondrej; Konno, Miki; Hosokai, Sou; Sonoyama, Nozomu; Norinaga, Koyo; Hayashi, Jun-ichiro

2008-01-01

The increasing interest in biomass, as a renewable source of energy, is stimulating a search for suitable biomass resources as well as the development of technologies for their effective utilization. This work concentrated on characteristics of processes occurring during pyrolytic gasification of upgraded food industry residues, namely residue from industrial production of liquid coffee, and assessed its suitability for conversion in an allothermal gasifier. The influence of several operating parameters on product composition was examined with three different laboratory-scale reactors, studying the primary pyrolysis and secondary pyrolysis of nascent volatiles, and the steam gasification of char. The experimental results show that a high degree of conversion of UCG into volatiles and gases (up to 88% C-basis) can be achieved by fast pyrolysis even at temperatures as low as 1073 K. In addition, the degree of conversion is not influenced by the presence or concentration of steam, which is an important factor in allothermal gasification. Mathematical simulation of an allothermal gasifier showed that net cold-gas efficiency as high as 86% can be reached

Selection, rejection and optimisation of pyrolytic graphite (PG) crystal analysers for use on the new IRIS graphite analyser bank

International Nuclear Information System (INIS)

Marshall, P.J.; Sivia, D.S.; Adams, M.A.; Telling, M.T.F.

2000-01-01

This report discusses design problems incurred by equipping the IRIS high-resolution inelastic spectrometer at the ISIS pulsed neutron source, UK with a new 4212 piece pyrolytic graphite crystal analyser array. Of the 4212 graphite pieces required, approximately 2500 will be newly purchased PG crystals with the remainder comprising of the currently installed graphite analysers. The quality of the new analyser pieces, with respect to manufacturing specifications, is assessed, as is the optimum arrangement of new PG pieces amongst old to circumvent degradation of the spectrometer's current angular resolution. Techniques employed to achieve these criteria include accurate calliper measurements, FORTRAN programming and statistical analysis. (author)

Detoxification and fermentation of pyrolytic sugar for ethanol production.

Science.gov (United States)

Wang, Hui; Livingston, Darrell; Srinivasan, Radhakrishnan; Li, Qi; Steele, Philip; Yu, Fei

2012-11-01

The sugars present in bio-oil produced by fast pyrolysis can potentially be fermented by microbial organisms to produce cellulosic ethanol. This study shows the potential for microbial digestion of the aqueous fraction of bio-oil in an enrichment medium to consume glucose and produce ethanol. In addition to glucose, inhibitors such as furans and phenols are present in the bio-oil. A pure glucose enrichment medium of 20 g/l was used as a standard to compare with glucose and aqueous fraction mixtures for digestion. Thirty percent by volume of aqueous fraction in media was the maximum additive amount that could be consumed and converted to ethanol. Inhibitors were removed by extraction, activated carbon, air stripping, and microbial methods. After economic analysis, the cost of ethanol using an inexpensive fermentation medium in a large scale plant is approximately $14 per gallon.

Hydrocarbons and trace metals in mussels in the Macaé coast: Preliminary assessment for a coastal zone under influence of offshore oil field exploration in southeastern Brazil.

Science.gov (United States)

Santiago, Igor U; Molisani, Mauricio M; Nudi, Adriana H; Scofield, Artur L; Wagener, Angela de L R; Limaverde Filho, Aricelso M

2016-02-15

Concentrations of PAHs and metals were obtained from mussels collected in beaches, coastal island and estuary of the Macaé coast, the main operational basin for offshore oil exploration in Brazil. This survey provides reference levels for scenarios of increasing exploration, as well as for other areas of the coast undergoing urbanization to support exploration. As expected, urban areas such as the Macaé river estuary presented high concentrations of PAHs, although unsuspected sites such the island also presented signs of contamination. PAH in mussels originated from pyrolytic and petrogenic sources. Metals were typical of non-contaminated coastal environments, although Cr concentrations were above Brazilian Reference Levels. Copyright © 2015 Elsevier Ltd. All rights reserved.

Covalent Modification of Highly Ordered Pyrolytic Graphite with a Stable Organic Free Radical by Using Diazonium Chemistry.

Science.gov (United States)

Seber, Gonca; Rudnev, Alexander V; Droghetti, Andrea; Rungger, Ivan; Veciana, Jaume; Mas-Torrent, Marta; Rovira, Concepció; Crivillers, Núria

2017-01-26

A novel, persistent, electrochemically active perchlorinated triphenylmethyl (PTM) radical with a diazonium functionality has been covalently attached to highly ordered pyrolytic graphite (HOPG) by electrografting in a single-step process. Electrochemical scanning tunneling microscopy (EC-STM) and Raman spectroscopy measurements revealed that PTM molecules had a higher tendency to covalently react at the HOPG step edges. The cross-section profiles from EC-STM images showed that there was current enhancement at the functionalized areas, which could be explained by redox-mediated electron tunneling through surface-confined redox-active molecules. Cyclic voltammetry clearly demonstrated that the intrinsic properties of the organic radical were preserved upon grafting and DFT calculations also revealed that the magnetic character of the PTM radical was preserved. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Aluminum doped nickel oxide thin film with improved electrochromic performance from layered double hydroxides precursor in situ pyrolytic route

International Nuclear Information System (INIS)

Shi, Jingjing; Lai, Lincong; Zhang, Ping; Li, Hailong; Qin, Yumei; Gao, Yuanchunxue; Luo, Lei; Lu, Jun

2016-01-01

Electrochromic materials with unique performance arouse great interest on account of potential application values in smart window, low-power display, automobile anti-glare rearview mirror, and e-papers. In this paper, high-performing Al-doped NiO porous electrochromic film grown on ITO substrate has been prepared via a layered double hydroxides(LDHs) precursor in situ pyrolytic route. The Al 3+ ions distributed homogenously within the NiO matrix can significantly influence the crystallinity of Ni-Al LDH and NiO:Al 3+ films. The electrochromic performance of the films were evaluated by means of UV–vis absorption spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry(CA) measurements. In addition, the ratio of Ni 3+ /Ni 2+ also varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range (58.4%), fast switching speed (bleaching/coloration times are 1.8/4.2 s, respectively) and excellent durability (30% decrease after 2000 cycles). The improved performance was owed to the synergy of large NiO film specific surface area and porous morphology, as well as Al doping stifled the formation of Ni 3+ making bleached state more pure. This LDHs precursor pyrolytic method is simple, low-cost and environmental benign and is feasible for the preparation of NiO:Al and other Al-doped oxide thin film. - Graphical abstract: The ratio of Ni 3+ /Ni 2+ varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range, fast switching speed and excellent durability. Display Omitted

Determination of vanadium in sea water by graphite furnace atomic absorption spectrometry with a tube coated with pyrolytic graphite

International Nuclear Information System (INIS)

Shimizu, Tokuo; Sakai, Kaoru

1981-01-01

The trace amount of vanadium in sea water was determined by graphite furnace atomic absorption spectrometry with a tube coated with pyrolytic graphite. To correct the background absorption, a deuterium lamp with a higher-brilliant thermal cathode was used. The sensitivity for vanadium increased 10 -- 20 fold by the use of the tube coated with pyrolytic graphite, and the utility lifetime of the tube was greatly extended. Vanadium(V) - 4-(2-pyridylazo)resorcinol (PAR) complexes were extracted into chloroform as an ion-pair with benzyldimethyltetradecylammonium (Zephiramine) cation alternatively. The sample of sea water, which was made to 0.1 N in sulfuric acid and 0.1% in hydrogen peroxide, was loaded onto the column of Dowex 1-X 4 resin (SO 4 2- -form). Vanadium was then eluted from the resin with 1 N sulfuric acid-0.1% hydrogen peroxide or 1 N hydrochloric acid-0.1% hydrogen peroxide evaporated to dry. After dissolution of the elute in 0.2 N nitric acid, vanadium was extracted. Secondly, the sample of sea water was adjusted to pH 5.0, and loaded onto the column of Chelex-100 resin. Vanadium was eluted from the resin with 2 N ammonia. The above two methods took much time, but the coprecipitation method was not so and recommended for the determination of vanadium in sea water. Vanadium was coprecipitated with iron(III) hydroxide-hydrous titanium(IV) oxide at pH 6.0. The precipitate was digested with nitric acid-hydrogen peroxide. The solution was diluted to 50 ml with water. The resulting solutions were employed to determine the vanadium concentration by the graphite furnace atomic absorption measurement. The trace amounts of vanadium in various kinds of the coastal sea water were determined by the coprecipitation method. (author)

Cf/C composites: correlation between CVI process parameters and Pyrolytic Carbon microstructure

Directory of Open Access Journals (Sweden)

F. Burgio

2014-10-01

Full Text Available Chemical Vapour Infiltration (CVI technique has been long used to produce carbon/carbon composites. The Pyrolytic Carbon (Py-C matrix infiltrated by CVI could have different microstructures, i.e. Rough Laminar (RL, Smooth Laminar (SL or Isotropic (ISO. These matrix microstructures, characterized by different properties, influence the mechanical behaviour of the obtained composites. Tailoring the process parameters, it is possible to direct the infiltration towards a specific Py-C type. However, the factors, influencing the production of a specific matrix microstructure, are numerous and interconnected, e.g. temperature, pressure, flow rates etc. Due to the complexity of the physical and chemical phenomena involved in CVI process, up to now it has not been possible to obtain a general correlation between CVI process parameters and Py–C microstructure. This study is aimed at investigating the relationship between infiltration temperature and the microstructure of obtained Py-C, for a pilot - sized CVI/CVD reactor. Fixing the other process parameters and varying only the temperature, from 1100°C to 1300°C, the Py-C infiltration was performed on fibrous preforms. Polarized light microscopy, with quantitative measurements of average extinction angle (Ae, and Raman spectroscopy were used to characterize the obtained Py-C microstructures

Cf/C composites: correlation between CVI process parameters and Pyrolytic Carbon microstructure

Directory of Open Access Journals (Sweden)

F. Burgio

2014-10-01

Full Text Available Chemical Vapour Infiltration (CVI technique has been long used to produce carbon/carbon composites. The Pyrolytic Carbon (Py-C matrix infiltrated by CVI could have different microstructures, i.e. Rough Laminar (RL, Smooth Laminar (SL or Isotropic (ISO. These matrix microstructures, characterized by different properties, influence the mechanical behaviour of the obtained composites. Tailoring the process parameters, it is possible to direct the infiltration towards a specific Py-C type. However, the factors, influencing the production of a specific matrix microstructure, are numerous and interconnected, e.g. temperature, pressure, flow rates etc. Due to the complexity of the physical and chemical phenomena involved in CVI process, up to now it has not been possible to obtain a general correlation between CVI process parameters and Py–C microstructure. This study is aimed at investigating the relationship between infiltration temperature and the microstructure of obtained Py-C, for a pilot - sized CVI/CVD reactor. Fixing the other process parameters and varying only the temperature, from 1100°C to 1300°C, the Py-C infiltration was performed on fibrous preforms. Polarized light microscopy, with quantitative measurements of average extinction angle (Ae, and Raman spectroscopy were used to characterize the obtained Py-C microstructures.

Pyrolytic carbon-coated stainless steel felt as a high-performance anode for bioelectrochemical systems.

Science.gov (United States)

Guo, Kun; Hidalgo, Diana; Tommasi, Tonia; Rabaey, Korneel

2016-07-01

Scale up of bioelectrochemical systems (BESs) requires highly conductive, biocompatible and stable electrodes. Here we present pyrolytic carbon-coated stainless steel felt (C-SS felt) as a high-performance and scalable anode. The electrode is created by generating a carbon layer on stainless steel felt (SS felt) via a multi-step deposition process involving α-d-glucose impregnation, caramelization, and pyrolysis. Physicochemical characterizations of the surface elucidate that a thin (20±5μm) and homogenous layer of polycrystalline graphitic carbon was obtained on SS felt surface after modification. The carbon coating significantly increases the biocompatibility, enabling robust electroactive biofilm formation. The C-SS felt electrodes reach current densities (jmax) of 3.65±0.14mA/cm(2) within 7days of operation, which is 11 times higher than plain SS felt electrodes (0.30±0.04mA/cm(2)). The excellent biocompatibility, high specific surface area, high conductivity, good mechanical strength, and low cost make C-SS felt a promising electrode for BESs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Erosion of pyrolytic carbon under high surface energy deposition from a pulsed hydrogen plasma

International Nuclear Information System (INIS)

Bolt, H.

1992-01-01

Carbon materials are widely applied as plasma facing materials in nuclear fusion devices and are also the prime candidate materials for the next generation of experimental fusion reactors. During operation these materials are frequently subjected to high energy deposition from plasma disruptions. The erosion of carbon materials is regarded as the main issue governing the operational lifetime of plasma facing components. Laboratory experiments have been performed to study the thermal erosion behaviour of carbon in a plasma environment. In the experiments the surface of pyrolytic carbon specimens was exposed to pulsed energy deposition of up to 3.8 MJ m -2 from a hydrogen plasma. The behaviour of the eroded carbon species in the plasma was measured by time-resolved and space-resolved spectroscopy. Intense line radiation of ionic carbon has been measured in the plasma in front of the carbon surface. The results show that the eroded carbon is immediately ionised in the vicinity of the material surface, with a fraction of it being ionised to the double-charged state. (Author)

The Erosion of Diamond and Highly Oriented Pyrolytic Graphite After 1.5 Years of Space Exposure

Science.gov (United States)

De Groh, Kim K.; Banks, Bruce A.

2018-01-01

Polymers and other oxidizable materials on the exterior of spacecraft in the low Earth orbit (LEO) space environment can be eroded due to reaction with atomic oxygen (AO). Therefore, in order to design durable spacecraft, it is important to know the LEO AO erosion yield (Ey, volume loss per incident oxygen atom) of materials susceptible to AO reaction. The Polymers Experiment was developed to determine the AO Ey of various polymers and other materials flown in ram and wake orientations in LEO. The experiment was flown as part of the Materials International Space Station Experiment 7 (MISSE 7) mission for 1.5 years on the exterior of the International Space Station (ISS). As part of the experiment, a sample containing Class 2A diamond (100 plane) and highly oriented pyrolytic graphite (HOPG, basal and edge planes) was exposed to ram AO and characterized for erosion. The materials were salt-sprayed prior to flight to provide isolated sites of AO protection. The Ey of the samples was determined through post-flight electron microscopy recession depth measurements. The experiment also included a Kapton H witness sample for AO fluence determination. This paper provides an overview of the MISSE 7 mission, a description of the flight experiment, the characterization techniques used, the mission AO fluence, and the LEO Ey results for diamond and HOPG (basal and edge planes). The data is compared to the Ey of pyrolytic graphite exposed to four years of space exposure as part of the MISSE 2 mission. The results indicate that diamond erodes, but with a very low Ey of 1.58 +/- 0.04 x 10(exp -26) cm(exp 3)/atom. The different HOPG planes displayed significantly different amounts of erosion from each other. The HOPG basal plane had an Ey of 1.05 +/- 0.08 x 10(exp -24) cm(exp 3)/atom while the edge plane had a lower Ey of only 5.38 +/- 0.90 x 10(exp -25) -cm(exp 3)/atom. The Ey data from this ISS spaceflight experiment provides valuable information for understanding of chemistry

Determining the phonon energy of highly oriented pyrolytic graphite by scanning tunneling microscope light emission spectroscopy

Science.gov (United States)

Uehara, Yoichi; Michimata, Junichi; Watanabe, Shota; Katano, Satoshi; Inaoka, Takeshi

2018-03-01

We have investigated the scanning tunneling microscope (STM) light emission spectra of isolated single Ag nanoparticles lying on highly oriented pyrolytic graphite (HOPG). The STM light emission spectra exhibited two types of spectral structures (step-like and periodic). Comparisons of the observed structures and theoretical predictions indicate that the phonon energy of the ZO mode of HOPG [M. Mohr et al., Phys. Rev. B 76, 035439 (2007)] can be determined from the energy difference between the cutoff of STM light emission and the step in the former structure, and from the period of the latter structure. Since the role of the Ag nanoparticles does not depend on the substrate materials, this method will enable the phonon energies of various materials to be measured by STM light emission spectroscopy. The spatial resolution is comparable to the lateral size of the individual Ag nanoparticles (that is, a few nm).

Study of initial stage in coal liquefaction. Increase in oil yield with suppression of retrogressive reaction during initial stage; Ekika hanno no shoki katei ni kansuru kenkyu. 1.

Energy Technology Data Exchange (ETDEWEB)

Uesugi, K.; Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

1996-10-28

For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogen transfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic effect between the improvement of liquefaction by suppressing polymerization/condensation at the initial stage of reaction through the prethermal treatment and the effective hydrogen transfer accompanied with the improvement of contact efficiency of coal/catalyst by the concentration of slurry at the stage of liquefaction. 4 refs., 8 figs.

Thermal behavior and pyrolytic degradation kinetics of polymeric mixtures from waste packaging plastics

Directory of Open Access Journals (Sweden)

R. Tuffi

2018-01-01

Full Text Available The thermal behavior and pyrolytic kinetic analysis of main waste polymers (polypropylene (PP, polyethylene film (PE, poly(ethylene terephthalate (PET, polystyrene (PS and three synthetic mixtures representing commingled postconsumer plastics wastes (CPCPWs output from material recovery facilities were studied. Thermogravimetry (TG pyrolysis experiments revealed that the thermal degradation of single polymers and the synthetic mixture enriched in PP occurred in one single step. The other two mixtures underwent a two-consecutive, partially overlapping degradation steps, whose peaks related to the first-order derivative of TG were deconvoluted into two distinct processes. Further TG experiments carried out on binary mixtures (PS/PP, PET/PP, PET/PEfilm and PP/PEfilm showed a thermal degradation reliance on composition, structure and temperatures of single polymer components. A kinetic analysis was made for each step using the Kissinger-Akahira-Sunose (KAS method, thus determining almost constant activation energy (Ea for pyrolysis of PS, PET, PP and PE film in the range 0.25<α<0.85, unlike for pyrolysis of CPCPWs, with particular reference to CPCPW1 and the second step of CPCPW2 and CPCPW3, both ascribable to degradation of PP and PE film. To account for the reliability of these values the integral isoconversional modified method developed by Vyazovkin was also applied.

Swift heavy ions induced irradiation effects in monolayer graphene and highly oriented pyrolytic graphite

International Nuclear Information System (INIS)

Zeng, J.; Yao, H.J.; Zhang, S.X.; Zhai, P.F.; Duan, J.L.; Sun, Y.M.; Li, G.P.; Liu, J.

2014-01-01

Monolayer graphene and highly oriented pyrolytic graphite (HOPG) were irradiated by swift heavy ions ( 209 Bi and 112 Sn) with the fluence between 10 11 and 10 14 ions/cm 2 . Both pristine and irradiated samples were investigated by Raman spectroscopy. It was found that D and D′ peaks appear after irradiation, which indicated the ion irradiation introduced damage both in the graphene and graphite lattice. Due to the special single atomic layer structure of graphene, the irradiation fluence threshold Φ th of the D band of graphene is significantly lower ( 11 ions/cm 2 ) than that (2.5 × 10 12 ions/cm 2 ) of HOPG. The larger defect density in graphene than in HOPG indicates that the monolayer graphene is much easier to be damaged than bulk graphite by swift heavy ions. Moreover, different defect types in graphene and HOPG were detected by the different values of I D /I D′ . For the irradiation with the same electronic energy loss, the velocity effect was found in HOPG. However, in this experiment, the velocity effect was not observed in graphene samples irradiated by swift heavy ions

Aluminum doped nickel oxide thin film with improved electrochromic performance from layered double hydroxides precursor in situ pyrolytic route

Energy Technology Data Exchange (ETDEWEB)

Shi, Jingjing; Lai, Lincong; Zhang, Ping; Li, Hailong; Qin, Yumei; Gao, Yuanchunxue; Luo, Lei; Lu, Jun, E-mail: lujun@mail.buct.edu.cn

2016-09-15

Electrochromic materials with unique performance arouse great interest on account of potential application values in smart window, low-power display, automobile anti-glare rearview mirror, and e-papers. In this paper, high-performing Al-doped NiO porous electrochromic film grown on ITO substrate has been prepared via a layered double hydroxides(LDHs) precursor in situ pyrolytic route. The Al{sup 3+} ions distributed homogenously within the NiO matrix can significantly influence the crystallinity of Ni-Al LDH and NiO:Al{sup 3+} films. The electrochromic performance of the films were evaluated by means of UV–vis absorption spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry(CA) measurements. In addition, the ratio of Ni{sup 3+}/Ni{sup 2+} also varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range (58.4%), fast switching speed (bleaching/coloration times are 1.8/4.2 s, respectively) and excellent durability (30% decrease after 2000 cycles). The improved performance was owed to the synergy of large NiO film specific surface area and porous morphology, as well as Al doping stifled the formation of Ni{sup 3+} making bleached state more pure. This LDHs precursor pyrolytic method is simple, low-cost and environmental benign and is feasible for the preparation of NiO:Al and other Al-doped oxide thin film. - Graphical abstract: The ratio of Ni{sup 3+}/Ni{sup 2+} varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range, fast switching speed and excellent durability. Display Omitted.

Preparation of pyrolytic carbon coating on graphite for inhibiting liquid fluoride salt and Xe135 penetration for molten salt breeder reactor

International Nuclear Information System (INIS)

Song, Jinliang; Zhao, Yanling; He, Xiujie; Zhang, Baoliang; Xu, Li; He, Zhoutong; Zhang, DongSheng; Gao, Lina; Xia, Huihao; Zhou, Xingtai; Huai, Ping; Bai, Shuo

2015-01-01

Highlights: • Rough laminar pyrolytic carbon coating (RLPyC) is prepared by a fixed-bed method. • The salt-infiltration into IG-110 is 13.5%, less than 0.01% of RLPyC under 1.5 atm. • The helium diffusion coefficient of RLPyC coated graphite is 2.16 × 10 −8 cm 2 /s. • The coated graphite can inhibit the liquid fluoride salt and Xe 135 penetration. - Abstract: A fixed-bed deposition method was used to prepare rough laminar pyrolytic carbon coating (RLPyC) on graphite for inhibiting liquid fluoride salt and Xe 135 penetration during use in molten salt breeder reactor. The RLPyC coating possessed a graphitization degree of 44% and had good contact with graphite substrate. A high-pressure reactor was constructed to evaluate the molten salt infiltration in the isostatic graphite (IG-110, TOYO TANSO CO., LTD.) and RLPyC coated graphite under 1.01, 1.52, 3.04, 5.07 and 10.13 × 10 5 Pa for 12 h. Mercury injection and molten-salt infiltration experiments indicated the porosity and the salt-infiltration amount of 18.4% and 13.5 wt% under 1.52 × 10 5 Pa of IG-110, which was much less than 1.2% and 0.06 wt% under 10.13 × 10 5 Pa of the RLPyC, respectively. A vacuum device was constructed to evaluate the Xe 135 penetration in the graphite. The helium diffusion coefficient of RLPyC coated graphite was 2.16 × 10 −12 m 2 /s, much less than 1.21 × 10 −6 m 2 /s of the graphite. Thermal cycle experiment indicated the coatings possessed excellent thermal stability. The coated graphite could effectively inhibit the liquid fluoride salt and Xe 135 penetration

Bactericidal activity of self-assembled palmitic and stearic fatty acid crystals on highly ordered pyrolytic graphite.

Science.gov (United States)

Ivanova, Elena P; Nguyen, Song Ha; Guo, Yachong; Baulin, Vladimir A; Webb, Hayden K; Truong, Vi Khanh; Wandiyanto, Jason V; Garvey, Christopher J; Mahon, Peter J; Mainwaring, David E; Crawford, Russell J

2017-09-01

The wings of insects such as cicadas and dragonflies have been found to possess nanostructure arrays that are assembled from fatty acids. These arrays can physically interact with the bacterial cell membranes, leading to the death of the cell. Such mechanobactericidal surfaces are of significant interest, as they can kill bacteria without the need for antibacterial chemicals. Here, we report on the bactericidal effect of two of the main lipid components of the insect wing epicuticle, palmitic (C16) and stearic (C18) fatty acids. Films of these fatty acids were re-crystallised on the surface of highly ordered pyrolytic graphite. It appeared that the presence of two additional CH 2 groups in the alkyl chain resulted in the formation of different surface structures. Scanning electron microscopy and atomic force microscopy showed that the palmitic acid microcrystallites were more asymmetric than those of the stearic acid, where the palmitic acid microcrystallites were observed to be an angular abutment in the scanning electron micrographs. The principal differences between the two types of long-chain saturated fatty acid crystallites were the larger density of peaks in the upper contact plane of the palmitic acid crystallites, as well as their greater proportion of asymmetrical shapes, in comparison to that of the stearic acid film. These two parameters might contribute to higher bactericidal activity on surfaces derived from palmitic acid. Both the palmitic and stearic acid crystallite surfaces displayed activity against Gram-negative, rod-shaped Pseudomonas aeruginosa and Gram-positive, spherical Staphylococcus aureus cells. These microcrystallite interfaces might be a useful tool in the fabrication of effective bactericidal nanocoatings. Nanostructured cicada and dragonfly wing surfaces have been discovered to be able physically kill bacterial cells. Here, we report on the successful fabrication of bactericidal three-dimensional structures of two main lipid

Co-pyrolysis of waste propylene and gas oil from Campos Basin: a case study; Tecnologia de co-pirolise de polipropileno pos-consumo com gasoleo da Bacia de Campos: um estudo de caso

Energy Technology Data Exchange (ETDEWEB)

Assumpcao, Luiz Carlos F.N. de; Aguiar, Monica Regina M.P. de [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil); Carbonell, Montserrat Motas [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2008-07-01

In this study the process of co-pyrolysis of plastic polypropylene residues with gas-oil was evaluated, varying the temperature and the amount of polypropylene. The co-pyrolysis is a promising route to minimize the environmental impact caused by the inadequate plastic disposal, preventing its accumulation and giving a better use of the not renewable raw material (oil). The polypropylene samples and gas-oil were submitted to the thermal co-pyrolysis in inert atmosphere, varying the temperature from 400 deg C to 500 deg C and the amount of PP from 0,1 to 1,0 g. The influence of gas-oil was evaluated carrying the co-pyrolysis in the absence of PP. The pyrolyzed liquids produced by this thermal treatment had been characterized by modified gaseous chromatography objectifying the evaluation of the diesel fractions generation. As a result, the increase of PP amount lead to a reduction in the income of the pyrolytic liquid and to increase of the amount of solid generated. The effect of the increase of temperature showed an inverse result. The addition of PP in the reactor showed little interference in diesel range of distillation in the co-pyrolysis. On the other hand, an increase in temperature favors the increase of products in this range of distillation. The results show that plastic residue co-pyrolysis is a potential method of chemical recycling. (author)

Lipid accumulation from pinewood pyrolysates by Rhodosporidium diobovatum and Chlorella vulgaris for biodiesel production.

Science.gov (United States)

Luque, Luis; Orr, Valerie C A; Chen, Sean; Westerhof, Roel; Oudenhoven, Stijn; Rossum, Guus van; Kersten, Sascha; Berruti, Franco; Rehmann, Lars

2016-08-01

This study evaluated the suitability of pinewood pyrolysates as a carbon source for lipid production and cultivation of the oleaginous yeast Rhodosporidium diobovatum and the microalgae Chlorella vulgaris. Thermal decomposition of pinewood and fractional condensation were used to obtain an oil rich in levoglucosan which was upgraded to glucose by acid hydrolysis. Blending of pyrolytic sugars with pure glucose in both nitrogen rich and nitrogen limited conditions was studied for R. diobovatum, and under nitrogen limited conditions for C. vulgaris. Glucose consumption rate decreased with increasing proportions of pyrolytic sugars increasing cultivation time. While R. diobovatum was capable of growth in 100% (v/v) pyrolytic sugars, C. vulgaris growth declined rapidly in blends greater than 20% (v/v) until no growth was detected in blends >40%. Finally, the effects of pyrolysis sugars on lipid composition was evaluated and biodiesel fuel properties were estimated based on the lipid profiles. Copyright © 2016 Elsevier Ltd. All rights reserved.

Jatropha waste meal as an alternative energy source via pressurized pyrolysis: A study on temperature effects

International Nuclear Information System (INIS)

Kongkasawan, Jinjuta; Nam, Hyungseok; Capareda, Sergio C.

2016-01-01

As an alternative energy source, Jatropha is a promising biomass resource due to its high content of oil contained in the seed. However, after the oil extraction process, more than 50% of initial weight remained as residue. This Jatropha de-oiled cake was considered a valuable feedstock for thermochemical conversion process due to its high volatile matter (73%) and energy content (20.5 MJ/kg). Pyrolysis turned biomass into solid product of biochar, liquid product (bio-oil and aqueous phase), and pyrolysis gas. The effects of pyrolysis temperature under the pressure of 0.69 MPa on the product yields and characteristics were investigated using a bench-scale batch reactor. The gross calorific value of pyrolytic oil was measured to be 35 MJ/kg with high carbon content (71%) and low oxygen content (10%). Phenols and hydrocarbons were the main compounds present in the pyrolytic oil. The heating value of the biochar was also high (28 MJ/kg), which was comparable to the fuel coke. More combustible gases were released at high pyrolysis temperature with methane as a main constituent. Pyrolysis temperature of 500 °C, was determined to be an optimum condition for the mass and energy conversions with 89% of the mass and 77% of the energy recovered. - Highlights: • Pressurized pyrolysis of Jatropha wastes at different temperatures was studied. • Full analysis of biochar, bio-oil and pyro gas at different temperatures were done. • Highest aromatics (32%) and HHV (35 MJ/kg) found in bio-oil at 500 °C. • Large amount of paraffins (C 13 –C 16 range) was found in bio-oil.

Preparation of pyrolytic carbon coating on graphite for inhibiting liquid fluoride salt and Xe{sup 135} penetration for molten salt breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Song, Jinliang [Key Laboratory of Nuclear Radiation and Nuclear Energy Technology, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Zhao, Yanling, E-mail: jlsong1982@yeah.net [School of Materials Science and Engineering, University of Jinan, Jinan 250022 (China); He, Xiujie; Zhang, Baoliang [Key Laboratory of Nuclear Radiation and Nuclear Energy Technology, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Xu, Li [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); He, Zhoutong; Zhang, DongSheng; Gao, Lina; Xia, Huihao; Zhou, Xingtai; Huai, Ping [Key Laboratory of Nuclear Radiation and Nuclear Energy Technology, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Bai, Shuo [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

2015-01-15

Highlights: • Rough laminar pyrolytic carbon coating (RLPyC) is prepared by a fixed-bed method. • The salt-infiltration into IG-110 is 13.5%, less than 0.01% of RLPyC under 1.5 atm. • The helium diffusion coefficient of RLPyC coated graphite is 2.16 × 10{sup −8} cm{sup 2}/s. • The coated graphite can inhibit the liquid fluoride salt and Xe{sup 135} penetration. - Abstract: A fixed-bed deposition method was used to prepare rough laminar pyrolytic carbon coating (RLPyC) on graphite for inhibiting liquid fluoride salt and Xe{sup 135} penetration during use in molten salt breeder reactor. The RLPyC coating possessed a graphitization degree of 44% and had good contact with graphite substrate. A high-pressure reactor was constructed to evaluate the molten salt infiltration in the isostatic graphite (IG-110, TOYO TANSO CO., LTD.) and RLPyC coated graphite under 1.01, 1.52, 3.04, 5.07 and 10.13 × 10{sup 5} Pa for 12 h. Mercury injection and molten-salt infiltration experiments indicated the porosity and the salt-infiltration amount of 18.4% and 13.5 wt% under 1.52 × 10{sup 5} Pa of IG-110, which was much less than 1.2% and 0.06 wt% under 10.13 × 10{sup 5} Pa of the RLPyC, respectively. A vacuum device was constructed to evaluate the Xe{sup 135} penetration in the graphite. The helium diffusion coefficient of RLPyC coated graphite was 2.16 × 10{sup −12} m{sup 2}/s, much less than 1.21 × 10{sup −6} m{sup 2}/s of the graphite. Thermal cycle experiment indicated the coatings possessed excellent thermal stability. The coated graphite could effectively inhibit the liquid fluoride salt and Xe{sup 135} penetration.

Synergistic methane formation on pyrolytic graphite due to combined H+ ion and H0 atom impact

International Nuclear Information System (INIS)

Haasz, A.A.; Davis, J.W.; Auciello, O.; Strangeby, P.C.; Vietzke, E.; Flaskamp, K.; Philipps, V.

1986-06-01

Exposure of graphite to multispecies hydrogenic impact, as is the case in tokamaks, could lead to synergistic mechanisms resulting in an enhancement of methane formation, and consequently in increased carbon erosion. We present results obtained in controlled experiments in our laboratories in Toronto and Juelich for the synergistic methane production due to combined sub-eV H 0 atoms and energetic H + ion impact on pyrolytic graphite. Flux densities were 10 14 -2x10 16 H 0 /cm 2 s for the sub-eV H 0 atoms and 6x10 12 -5x10 15 H + /cm 2 for H + ions of 300 eV to 2.5 keV energy. Synergistic factors (defined as the ratio of methane formation rate due to combined H 0 and H + fluxes to the sum of the formation rates due to separate species impact) ranged from about 1.5-15 for the experimental parameters used. In addition, a spectrum of formed hydrocarbons in the synergistic reaction of H + and H 0 on graphite is presented

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

NARCIS (Netherlands)

Babych, Igor V.; van der Hulst, M.; Lefferts, Leonardus; Moulijn, J.A.; Seshan, Kulathuiyer; O'Connor, P.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na2CO3) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor

Online time-differential perturbed angular correlation study with an 19O beam - Residence sites of oxygen atoms in highly oriented pyrolytic graphite

International Nuclear Information System (INIS)

Sato, W.; Ueno, H.; Watanabe, H.; Miyoshi, H.; Yoshimi, A.; Kameda, D.; Ito, T.; Shimada, K.; Kaihara, J.; Suda, S.; Kobayashi, Y.; Shinohara, A.; Ohkubo, Y.; Asahi, K.

2008-01-01

The online time-differential perturbed angular correlation (TDPAC) method was applied to a study of the physical states of a probe 19 F, the β - decay product of 19 O (t 1/2 = 26.9 s), implanted in highly oriented pyrolytic graphite. The observed magnitude of the electric field gradient at the probe nucleus, |V zz | = 2.91(17) x 10 22 V m -2 , suggests that the incident 19 O atoms are stabilized at an interlayer position with point group C 3v . Exhibiting observed TDPAC spectra having a clear sample-to-detector configuration dependence, we demonstrate the applicability of the present online method with a short-lived radioactive 19 O beam

Online time-differential perturbed angular correlation study with an 19O beam - Residence sites of oxygen atoms in highly oriented pyrolytic graphite

Science.gov (United States)

Sato, W.; Ueno, H.; Watanabe, H.; Miyoshi, H.; Yoshimi, A.; Kameda, D.; Ito, T.; Shimada, K.; Kaihara, J.; Suda, S.; Kobayashi, Y.; Shinohara, A.; Ohkubo, Y.; Asahi, K.

2008-01-01

The online time-differential perturbed angular correlation (TDPAC) method was applied to a study of the physical states of a probe 19F, the β- decay product of 19O (t1/2 = 26.9 s), implanted in highly oriented pyrolytic graphite. The observed magnitude of the electric field gradient at the probe nucleus, ∣Vzz∣ = 2.91(17) × 1022 V m-2, suggests that the incident 19O atoms are stabilized at an interlayer position with point group C3v. Exhibiting observed TDPAC spectra having a clear sample-to-detector configuration dependence, we demonstrate the applicability of the present online method with a short-lived radioactive 19O beam.

Effects of deposited pyrolytic carbon on some mechanical properties of zircaloy-4 tubes. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Shrkawy, S W; Abdel-razek, I D; El-Sayed, H A [Metallurgy Department, Nuclear Research Center, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Zircaloy cladding tubes are not compatible with the uranium fuel pellets as they suffer from failure due to pelletclad interaction (PCI). A carbon coating, as used in the canadian CANLUB fuel elements, is thought to improve the cladding performance with respect to the PCI problem. In this paper pyrolytic carbon coating was deposited on zircaloy-4 cladding tubes by the thermal cracking of commercial butant gas at the temperature range 250-450 degree C. In order to evaluate the effect of gaseous species on the mechanical properties of the tubes tensile and microhardness testing measurements were performed on samples prepared from the coated tubes. The fractured surface of the tensile zircaloy tubes and the deposited carbon coating, both, were examined by the SEM. The results of the tensile tests of zircaloy-4 tubes indicated that the coating process has insignificant effect on the ultimate strength of the tubes tested. The values of Vickers hardness numbers were not significantly changed across the tubes thickness. The microstructure of deposited carbon, due to the cracking process, was granular in all the temperature range (250-450 degree C) studied. 9 figs., 1 tab.

Pyrolytic graphite as an efficient second-order neutron filter at tuned positions of boundary crossing

International Nuclear Information System (INIS)

Adib, M.; Abdel Kawy, A.; Habib, N.; El Mesiry, M.

2010-01-01

An investigation of pyrolytic graphite (PG) crystal as an efficient second order neutron filter at tuned boundary crossings has been carried out. The neutron transmission through PG crystal at these tuned crossing points as a function of first- and second-order wavelengths were calculated in terms of PG mosaic spread and thickness. The filtering features of PG crystals at these tuned boundary crossings were deduced. It was shown that, there are a large number of tuned positions at double and triple boundary crossings of the curves (hkl) are very promising as tuned filter positions. However, only fourteen of them are found to be most promising ones. These tuned positions are found to be within the neutron wavelengths from 0.133 up to 0.4050 nm. A computer package GRAPHITE has been used in order to provide the required calculations in the whole neutron wavelength range in terms of PG mosaic spread and its orientation with respect to incident neutron beam direction. It was shown that 0.5 cm thick PG crystal with angular mosaic spread of 2 0 is sufficient to remove 2nd-order neutrons at the wavelengths corresponding to the positions of the intersection boundaries curves (hkl).

Reactions of modulated molecular beams with pyrolytic graphite IV. Water vapor

International Nuclear Information System (INIS)

Olander, D.R.; Acharya, T.R.; Ullman, A.Z.

1977-01-01

The reaction of water vapor with the prism plane face of anneal pyrolytic graphite was investigated by modulated molecular beam--mass spectrometry methods. The equivalent water vapor pressure of the beam was approx.2 x 10 -5 Torr and the graphite temperature was varied from 300 to 2500 0 K. The mechanism was deduced from three types of experiments: isotope exchange utilizing modulated H 2 O and steady D 2 O beams; measurements of the phase difference between H 2 O and neon reflected from the surface from a mixed primary beam of these species; and reaction of a modulated H 2 O beam to produce CO and H 2 . Based upon the isotope exchange experiments chemisorption of water on graphite was found to be dissociative and reversible. Incident water molecules chemisorbed with a sticking probability of 0.15 +- 0.02 to form the complexes C--OH and C--H. Recombination of the surface complexes reverses the adsorption step and is responsible for the isotope exchange properties of the graphite surface. This process is unactivated. Reaction to produce CO and H 2 also results from collisions of the primary surface complexes, but this step has an activation energy of 170 kJ/mole. This reaction yields bound complexes tentatively identified as C--O and H--C--H, which then decompose to produce the stable reaction products. All of the above steps exhibit characteristic times on the order of milliseconds, and are therefore detectable by the modulated beam method. All surface intermediates are strongly affected by solution and diffusion in the bulk of the solid

Production of valuable pyrolytic oils from mixed Municipal Solid Waste (MSW in Indonesia using non-isothermal and isothermal experimental

Directory of Open Access Journals (Sweden)

Indra Mamad Gandidi

2017-09-01

Full Text Available Municipal solid waste (MSW, disposed of at open dumping sites, poses health risks, contaminates surface water, and releases greenhouse gasses such as methane. However, pyrolysis offers the opportunity to convert MSW into Bio-Oil (BO for clean energy resource. In this paper, an MSW sample consisting of plastic, paper and cardboard, rubber and textiles, and vegetable waste is pyrolysed on a laboratory scale in a fixed-bed vacuum reactor. In the non-isothermal process, the sample was fed into the reactor and then heated. In the isothermal process, the reactor is first heated and then the sample is added. The non-isothermal process created greater BO in both quality and quantity. The BO had a larger amount of gasoline species than diesel-48 fuel, with at 33.44%the BO produced by isothermal pyrolysis and 36.42% in non-isothermal pyrolysis. However the product of isothermal pyrolysis had a higher acid content that reduced its heating value.

Pyrolytic indices of diagenetic transformation of lignin as biogeochemical proxies for soil organic matter quality and C storage potential

Science.gov (United States)

Jiménez-González, Marco A.; Almendros, Gonzalo; Álvarez, Ana M.; Jiménez-Morillo, Nicasio T.; González-Vila, Francisco J.

2017-04-01

The environmental factors involved in soil organic carbon sequestration remain unclear. The functional relationships between the macromolecular structure of the soil organic matter (SOM) and its resilience has been a constant in classical biogeochemical models. Other more recent hypotheses have postulated that preservation by soil minerals may play a chief role in the accumulation of stable SOM forms. However, additional experimental data are required to demonstrate a cause-to-effect relationship between preservation and stabilization. Some authors might consider that models neglecting the role of macromolecular structure are swapping cause and effect i.e., that SOM structurally flexible, weakly condensed and having 'open' structures is the one with high potential to interact with the soil mineral matrix, leading to stable microaggregates. In this study up to 35 topsoil samples (0-5 cm) were collected from different Spanish soils with contrasted values of organic C (the dependent variable), geological substrate and vegetation type. A wide array of uni- and multivariate chemometric models were applied to independent variables consisting of total abundances of the major aromatic compounds, i.e., alkylbenzenes and methoxyphenols released from whole soil samples using pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS). These two families of compounds were selected since they are classically considered to inform on the degree of microbial reworking of lignins, which is an important precursor of the aromatic moiety of the SOM. A series of pyrolytic surrogate indices (aiming to express SOM diagenetic transformation in relation to the original biogenic molecular composition) were especially successful in forecasting SOC, viz: a) ratio between alkylbenzenes and methoxyphenols, b) ratio between short-chain (C0-C4) and long-chain (>C4) alkylbenzenes, c) ratio between methoxyphenols and short-chain alkylbenzenes, and d) ratios between methoxyphenols with different side

Effect of oxygen and hydrogen on microstructure of pyrolytic carbon deposited from thermal decomposition of methane and ethanol

Science.gov (United States)

Ren, Biyun; Zhang, Shouyang; He, LiQun; Gu, Shengyue

2018-05-01

Chemical vapor infiltration (CVI) is the most extensive industrial preparation of carbon/carbon (C/C) composites. Precursor affects the CVI process considerably. In the present study, using carbon fiber bundles as preforms, methane and ethanol as precursors, the C/C composites were densified by decomposition of various gases in CVI. The thickness and texture of deposited pyrolytic carbon (PyC) were characterized by polarized light microscopy (PLM). The microstructure of PyC was analyzed by Raman spectroscopy. The morphologies of PyC were characterized by scanning electron microscopy (SEM). The composition of PyC was detected by X-ray photoelectron spectroscopy (XPS). Adding hydrogen in methane precursor resulted in a sharp decrease in the deposition rate and texture of PyC. Mixture of methane and ethanol as the precursor improved the deposition rate and texture remarkably. Besides, O element in ethanol was not remained as a constitution of PyC, and it was removed before the formation of PyC.

Effects of Processing Parameters on the Density and Microstructure of Pyrolytic Carbon

International Nuclear Information System (INIS)

Kim, Weon Ju; Park, Jeong Nam; Park, Jong Hoon; Cho, Moon Sung; Lee, Young Woo; Park, Ji Yeon

2007-01-01

Chemical vapor deposition (CVD) of pyrolytic carbon (PyC) and silicon carbide (SiC) has been applied to TRISO-coated fuel particles for high-temperature gas-cooled reactors (HTGR). The porous PyC coating layer, called the buffer layer, attenuates fission recoils and provides void volume for gaseous fission products and carbon monoxide. The inner PyC layer acts as a containment to gaseous products. The outer PyC layer protects the SiC coating layer by inducing a compressive stress and provides chemical compatibility with a graphite matrix in the fuel compact. The PyC layers undergo shrinkage due to neutron irradiation, affecting the design and modeling of fuel particles. Because the dimensional change of PyC depends on the detailed microstructure of PyC, it differs from one fabrication route to another one. This requires a new design of irradiation experiment applicable to spherical objects and leads to an international collaborative work called PYCASSO (PYrocarbon irradiation for Creep And Swelling/Shrinkage of Objects). KAERI proposed four different types of PyC layers coated on ZrO 2 particles, buffer with a density of 1.0 and dense PyCs with densities of 1.7, 1.9 and 2.1 g/cm 3 , for the irradiation experiment. In this study, we fabricated PyC-coated particles with various coating densities for supporting the PYCASSO experiment. We also investigated effects of processing parameters such as temperature, hydrocarbon concentration and gas flow rate on the density and microstructure of the PyC layer

Co-pyrolysis behaviour and kinetic of two typical solid wastes in China and characterisation of activated carbon prepared from pyrolytic char.

Science.gov (United States)

Ma, Yuhui; Niu, Ruxuan; Wang, Xiaona; Wang, Qunhui; Wang, Xiaoqiang; Sun, Xiaohong

2014-11-01

This is the first study on the co-pyrolysis of spent substrate of Pleurotus ostreatus and coal tar pitch, and the activated carbon prepared from the pyrolytic char. Thermogravimetry (TG) analysis was carried out taking spent substrate, coal tar pitch and spent substrate-coal tar pitch mixture. The activation energies of pyrolysis reactions were obtained via the Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose methods. The kinetic models were determined by the master-plots method. The activated carbons were characterised by N2-adsorption, Fourier transform infrared spectroscopy and X-ray diffraction. Experimental results demonstrated a synergistic effect happened during co-pyrolysis, which was characterised by a decreased maximum decomposition rate and an enhanced char yield. The average activation energies of the pyrolysis reactions of spent substrate, coal tar pitch and the mixture were 115.94, 72.92 and 94.38 kJ mol(-1) for the Flynn-Wall-Ozawa method, and 112.17, 65.62 and 89.91 kJ mol(-1) for the Kissinger-Akahira-Sunose method. The reaction model functions were f(α) = (1-α)(3.42), (1-α)(1.72) and (1-α)(3.07) for spent substrate, coal tar pitch and the mixture, respectively. The mixture char-derived activated carbon had a Brunauer-Emmett-Teller surface area up to 1337 m(2) g(-1) and a total pore volume of 0.680 cm(3) g(-1). Mixing spent substrate with coal tar pitch led to the creation of more micropores and a higher surface area compared with the single spent substrate and coal tar pitch char. Also, the mixture char-derived activated carbon had a higher proportion of aromatic stacking. This study provides a reference for the utilisation of spent substrate and coal tar pitch via co-pyrolysis, and their pyrolytic char as a promising precursor of activated carbon. © The Author(s) 2014.

Characterization of fast pyrolysis products generated from several western USA woody species

Science.gov (United States)

Jacqueline M. Jarvis; Deborah S. Page-Dumroese; Nathaniel M. Anderson; Yuri Corilo; Ryan P. Rodgers

2014-01-01

Woody biomass has the potential to be utilized at an alternative fuel source through its pyrolytic conversion. Here, fast pyrolysis bio-oils derived from several western USA woody species are characterized by negative-ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS) to determine molecular-level composition. The...

Electronic Transport and Raman Spectroscopy Characterization in Ion-Implanted Highly Oriented Pyrolytic Graphite

Science.gov (United States)

de Jesus, R. F.; Turatti, A. M.; Camargo, B. C.; da Silva, R. R.; Kopelevich, Y.; Behar, M.; Balzaretti, N. M.; Gusmão, M. A.; Pureur, P.

2018-02-01

We report on Raman spectroscopy, temperature-dependent in-plane resistivity, and in-plane magnetoresistance experiments in highly oriented pyrolytic graphite (HOPG) implanted with As and Mn. A pristine sample was also studied for comparison. Two different fluences were applied, φ = 0.5× 10^{16} {ions}/{cm}2 and φ = 1.0× 10^{16} {ions}/{cm}2. The implantations were carried out with 20 keV ion energy at room temperature. The Raman spectroscopy results reveal the occurrence of drastic changes of the HOPG surface as a consequence of the damage caused by ionic implantation. For the higher dose, the complete amorphization limit is attained. The resistivity and magnetoresistance results were obtained placing electrical contacts on the irradiated sample surface. Owing to the strong anisotropy of HOPG, the electrical current propagates mostly near the implanted surface. Shubnikov-de Haas (SdH) oscillations were observed in the magnetoresistance at low temperatures. These results allow the extraction of the fundamental SdH frequencies and the carriers' effective masses. In general, the resistivity and magnetoresistance results are consistent with those obtained from Raman measurements. However, one must consider that the electrical conduction in our samples occurs as in a parallel association of a largely resistive thin sheet at the surface strongly modified by disorder with a thicker layer where damage produced by implantation is less severe. The SdH oscillations do not hint to significant changes in the carrier density of HOPG.

Transesterification of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil by tin catalysts

International Nuclear Information System (INIS)

Shah, Mazloom; Tariq, Muhammad; Ali, Saqib; Guo, Qing-Xiang; Fu, Yao

2014-01-01

The methanolysis of jojoba oil has been studied in the presence of tin powder, dibutyltin diacetate (C 4 H 9 ) 2 Sn(OOCCH 3 ) 2 , dioctyltin diacetate (C 8 H 17 ) 2 Sn(OOCCH 3 ) 2 , dibutyltin oxide (C 4 H 9 ) 2 SnO, dioctyltin oxide (C 8 H 17 ) 2 SnO, diphenyltin oxide (C 6 H 5 ) 2 SnO, dibutyltin chloride dihydroxide (C 4 H 9 ) 2 Sn(OH) 2 Cl, butyltinhydroxide hydrate (C 4 H 9 )Sn(=O)OH.xH 2 O, Ni nanoparticles and Pd nanoparticles act as catalysts. Among these, 1 weight % of dibutyltin diacetate shows the maximum conversion. Then, methanolysis of sunflower oil, neem oil, rocket seed oil and linseed oil into methyl esters studied in the presence of 1% dibutyltin diacetate as a catalyst and was compared their percentage conversions. The experimental yield for the conversion of jojoba oil, sunflower oil, neem oil, rocket seed oil and linseed oil into biodiesel was found to be 71%, 51%, 50.78%, 40.90% and 39.66%, respectively. The experimental yield of the conversion of jojoba oil into methyl esters was found to be increased up to 96% by increasing reaction time, without emulsion formation. The synthesis of jojoba seed oil biodiesel (JSOB), soybean oil biodiesel (SOB), neem oil biodiesel (NOB), rocket seed oil biodiesel (RSOB) and linseed oil biodiesel (LSOB) was confirmed by NMR ( 1 H and 13 C) and FT-IR analyses of biodiesel. - Highlights: • Transesterification of jojoba oil into biodiesel by tin and nano catalysts. • 1 weight % dibutyltin diacetate showed highest yield at 60 °C. • Catalytic conversion comparison of five oils using dibutyltin diacetate • The experimental yield of the conversion of jojoba oil increased with time. • FT-IR and NMR ( 1 H and 13 C) characterization

Surface modification of highly oriented pyrolytic graphite by reaction with atomic nitrogen at high temperatures

International Nuclear Information System (INIS)

Zhang Luning; Pejakovic, Dusan A.; Geng Baisong; Marschall, Jochen

2011-01-01

Dry etching of {0 0 0 1} basal planes of highly oriented pyrolytic graphite (HOPG) using active nitridation by nitrogen atoms was investigated at low pressures and high temperatures. The etching process produces channels at grain boundaries and pits whose shapes depend on the reaction temperature. For temperatures below 600 deg. C, the majority of pits are nearly circular, with a small fraction of hexagonal pits with rounded edges. For temperatures above 600 deg. C, the pits are almost exclusively hexagonal with straight edges. The Raman spectra of samples etched at 1000 deg. C show the D mode near 1360 cm -1 , which is absent in pristine HOPG. For deep hexagonal pits that penetrate many graphene layers, neither the surface number density of pits nor the width of pit size distribution changes substantially with the nitridation time, suggesting that these pits are initiated at a fixed number of extended defects intersecting {0 0 0 1} planes. Shallow pits that penetrate 1-2 graphene layers have a wide size distribution, which suggests that these pits are initiated on pristine graphene surfaces from lattice vacancies continually formed by N atoms. A similar wide size distribution of shallow hexagonal pits is observed in an n-layer graphene sample after N-atom etching.

Use of carbon dioxide as a reaction medium in the thermo-chemical process for the enhanced generation of syngas and tuning adsorption ability of biochar

International Nuclear Information System (INIS)

Cho, Dong-Wan; Kwon, Eilhann E.; Song, Hocheol

2016-01-01

Highlights: • Utilizing CO_2 as a reaction medium in thermo-chemical conversion of aquatic biomass. • Enhanced generation of syngas in the presence of CO_2. • Considerable reduction of pyrolytic oil in CO_2-assisted pyrolysis. • Generation of biochar with high surface area and more porous structure by CO_2. - Abstract: This study mechanistically investigated the influences of CO_2 on syngas (H_2 and CO) production during thermo-chemical conversion of red seaweed, and further explored the possible utility of the produced biochar as a medium for adsorption of inorganic/organic contaminants in aqueous phase. In order to elucidate the key roles of CO_2 in the thermo-chemical process, the composition analysis of syngas and the qualitative analysis of pyrolytic oil were conducted and compared with those in pyrolysis in N_2 condition. Pyrolysis of red seaweed in the presence of CO_2 led to the enhanced generation of syngas at the entire experimental temperatures. For example, the ratio of CO to H_2 in the presence of CO_2 at 620 °C was enhanced by ∼400%, as compared to the case in N_2. This enhanced generation of syngas resulted in significant pyrolytic oil reduction by ∼70% at 620 °C via the unknown reactions between VOCs and CO_2. In addition, biochar generated in the CO_2 environment exhibited comparatively higher surface area (61 m"2 g"−"1) and more porous structure. The morphological modification induced by CO_2 provided the favorable condition for removal of methylene blue from the aqueous phase. Thus, this study experimentally demonstrated that exploiting CO_2 as a reaction medium would provide an attractive option for the enhanced generation of syngas and the tuned adsorption capability of biochar.

Production of phenolic-rich bio-oil from catalytic fast pyrolysis of biomass using magnetic solid base catalyst

International Nuclear Information System (INIS)

Zhang, Zhi-bo; Lu, Qiang; Ye, Xiao-ning; Li, Wen-tao; Hu, Bin; Dong, Chang-qing

2015-01-01

Highlights: • Phenolic-rich bio-oil was selectively produced from catalytic fast pyrolysis of biomass using magnetic solid base catalyst. • The actual yield of twelve major phenolic compounds reached 43.9 mg/g. • The peak area% of all phenolics reached 68.5% at the catalyst-to-biomass ratio of 7. • The potassium phosphate/ferroferric oxide catalyst possessed promising recycling properties. - Abstract: A magnetic solid base catalyst (potassium phosphate/ferroferric oxide) was prepared and used for catalytic fast pyrolysis of poplar wood to selectively produce phenolic-rich bio-oil. Pyrolysis–gas chromatography/mass spectrometry experiments were conducted to investigate the effects of pyrolysis temperature and catalyst-to-biomass ratio on the product distribution. The actual yields of important pyrolytic products were quantitatively determined by the external standard method. Moreover, recycling experiments were performed to determine the re-utilization abilities of the catalyst. The results showed that the catalyst exhibited promising activity to selectively produce phenolic-rich bio-oil, due to its capability of promoting the decomposition of lignin to generate phenolic compounds and meanwhile inhibiting the devolatilization of holocellulose. The maximal phenolic yield was obtained at the pyrolysis temperature of 400 °C and catalyst-to-biomass ratio of 2. The concentration of the phenolic compounds increased monotonically along with the increasing of the catalyst-to-biomass ratio, with the peak area% value increasing from 28.1% in the non-catalytic process to as high as 68.5% at the catalyst-to-biomass ratio of 7. The maximal total actual yield of twelve quantified major phenolic compounds was 43.9 mg/g, compared with the value of 29.0 mg/g in the non-catalytic process. In addition, the catalyst could be easily recovered and possessed promising recycling properties.

Cascade Production of Lactic Acid from Universal Types of Sugars Catalyzed by Lanthanum Triflate.

Science.gov (United States)

Liu, Dajiang; Kim, Kwang Ho; Sun, Jian; Simmons, Blake A; Singh, Seema

2018-02-09

Lignocellulosic biomass conversion into value-added platform chemicals in the non-toxic, water-tolerant Lewis acid, and water solutions bears the hallmark of green chemistry. Lactic acid derived from biomass is an important chemical building block for biodegradable polymers such as polylactide. Herein, a universal method of converting lignocellulosic sugars into lactic acid using catalytic amount of water-stable Lewis acid La(OTf) 3 is demonstrated. The lignocellulosic sugars studied in this work include 1) pyrolytic sugars from pyrolysis oil, and 2) sugars derived from ionic liquid (IL)-pretreated biomass. Under moderate conditions (250 °C, 1 h), levoglucosan (major pyrolytic sugar), glucose, and xylose were converted into lactic acid with carbon-based molar yields of 75, 74, and 61 %, respectively. Furthermore, roughly 49 mol % (based on levoglucosan) and 74 wt % (relative to pretreated biomass) of lactic acid were obtained from the conversion of pyrolytic sugars and sugar-rich fraction after lignin removal from switchgrass, respectively. To our knowledge, this is the first reported conversion of pyrolytic sugar into lactic acid by chemocatalysis and also lignocellulosic sugars are converted into lactic acid without hydrolysis. This approach could potentially be extended to other lignocellulosic sugars after simple removal of lignin from biomass pretreatment, rendering moderate to high yields of lactic acid. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tritium permeation behavior through pyrolytic carbon in tritium production using high-temperature gas-cooled reactor for fusion reactors

Directory of Open Access Journals (Sweden)

H. Ushida

2016-12-01

Full Text Available Under tritium production method using a high-temperature gas-cooled reactor loaded Li compound, Li compound has to be coated by ceramic materials in order to suppress the spreading of tritium to the whole reactor. Pyrolytic carbon (PyC is a candidate of the coating material because of its high resistance for gas permeation. In this study, hydrogen permeation experiments using a PyC-coated isotropic graphite tube were conducted and hydrogen diffusivity, solubility and permeability were evaluated. Tritium permeation behavior through PyC-coated Li compound particles was simulated by using obtained data. Hydrogen permeation flux through PyC in a steady state is proportional to the hydrogen pressure and is larger than that through Al2O3 which is also candidate coating material. However, total tritium leak within the supposed reactor operation period through the PyC-coated Li compound particles is lower than that through the Al2O3-coated ones because the hydrogen absorption capacity in PyC is considerably larger than that in Al2O3.

Vacuum pyrolysis of waste tires with basic additives

International Nuclear Information System (INIS)

Zhang Xinghua; Wang Tiejun; Ma Longlong; Chang Jie

2008-01-01

Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na 2 CO 3 , NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) ∼205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na 2 CO 3 addition. Pyrolysis gas was mainly composed of H 2 , CO, CH 4 , CO 2 , C 2 H 4 and C 2 H 6 . Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher

Thermal desorption spectroscopy of pyrolytic graphite cleavage faces after keV deuterium irradiation at 330-1000 K

International Nuclear Information System (INIS)

Gotoh, Y.; Yamaki, T.; Tokiguchi, K.

1992-01-01

Thermal desorption spectroscopy (TDS) measurements were made on D 2 and CD 4 from surface layers of pyrolytic graphite cleavage faces after 3 keV D + 3 irradiation to 1.5 x 10 18 D/cm 2 at irradiation temperatures from 330 to 1000 K. Thermal desorption of both D 2 and CD 4 was observed to rise simultaneously at around 700 K. The D 2 peak was found at T m = 900-1000 K, while the CD 4 peak appeared at a lower temperature, 800-840 K. The T m for the D 2 TDS increased, while that for the CD 4 decreased with increasing irradiation temperature. These results obviously indicate that the D 2 desorption is detrapping/recombination limited, while the CD 4 desorption is most likely to be diffusion limited. The amount of thermally desorbed D 2 after the D + irradiation was observed to monotonously decrease as the irradiation temperature was increased from 330 to 1000 K. These tendencies agreed with previous results for the irradiation temperature dependencies of both C1s chemical shift (XPS) and the interlayer spacing, d 002 (HRTEM), on the graphite basal face. (orig.)

Investigation on the recombination kinetics of the pyrolytic free-radicals in the irradiated polyimide

International Nuclear Information System (INIS)

Sun Chengyue; Wu Yiyong; Yue Long; Shi Yaping; Xiao Jingdong

2012-01-01

Highlights: ► Free radicals behavior was exposure during the irradiation and anneal during the post storage. ► Both of the recombination and oxygen reaction affect the post-annealing evolution of free radicals. ► The activation energy and the surface reaction rate were calculated by the analysis of the free radical anneal process. - Abstract: The free radical behavior of 60 and 110 keV proton-irradiated polyimide were investigated using electron paramagnetic resonance measurements. The results indicate that during proton irradiation, a type of pyrolytic carbon free radical was formed with a g value of 2.0025. The radical population was found, after proton irradiation to decrease in a combination of an exponential and linear modes with an annealing time in the range of 50–120 °C. The exponential part indicated a radical recombination process while the linear part is due to the reaction of the radical with the ambient. Using the annealing results, the recombination activation energy of the radicals was determined as 12.4 ± 0.2 and 17.6 ± 0.2 kJ/mol for 60 and 110 keV irradiated polyimide, respectively, with a surface reaction rate of about 0.02/h. It is possible that the kinetic study presented here is used as one of the criteria for predicting the optical properties of polyimide material in spacecraft. The mechanism of the free radical evolution will be discussed in this paper.

Comparative studies of the pyrolytic and kinetic characteristics of maize straw and the seaweed Ulva pertusa.

Directory of Open Access Journals (Sweden)

Naihao Ye

Full Text Available Seaweed has attracted considerable attention as a potential biofuel feedstock. The pyrolytic and kinetic characteristics of maize straw and the seaweed Ulva pertusa were studied and compared using heating rates of 10, 30 and 50°C min(-1 under an inert atmosphere. The activation energy, and pre-exponential factors were calculated by the Flynn-Wall-Ozawa (FWO, Kissinger-Akahira-Sunose (KAS and Popescu methods. The kinetic mechanism was deduced by the Popescu method. The results indicate that there are three stages to the pyrolysis; dehydration, primary devolatilization and residual decomposition. There were significant differences in average activation energy, thermal stability, final residuals and reaction rates between the two materials. The primary devolatilization stage of U. pertusa can be described by the Avramic-Erofeev equation (n=3, whereas that of maize straw can be described by the Mampel Power Law (n=2. The average activation energy of maize straw and U. pertusa were 153.0 and 148.7 KJ mol(-1, respectively. The pyrolysis process of U.pertusa would be easier than maize straw. And co-firing of the two biomass may be require less external heat input and improve process stability. There were minor kinetic compensation effects between the pre-exponential factors and the activation energy.

Comparative studies of the pyrolytic and kinetic characteristics of maize straw and the seaweed Ulva pertusa.

Science.gov (United States)

Ye, Naihao; Li, Demao; Chen, Limei; Zhang, Xiaowen; Xu, Dong

2010-09-10

Seaweed has attracted considerable attention as a potential biofuel feedstock. The pyrolytic and kinetic characteristics of maize straw and the seaweed Ulva pertusa were studied and compared using heating rates of 10, 30 and 50°C min(-1) under an inert atmosphere. The activation energy, and pre-exponential factors were calculated by the Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS) and Popescu methods. The kinetic mechanism was deduced by the Popescu method. The results indicate that there are three stages to the pyrolysis; dehydration, primary devolatilization and residual decomposition. There were significant differences in average activation energy, thermal stability, final residuals and reaction rates between the two materials. The primary devolatilization stage of U. pertusa can be described by the Avramic-Erofeev equation (n=3), whereas that of maize straw can be described by the Mampel Power Law (n=2). The average activation energy of maize straw and U. pertusa were 153.0 and 148.7 KJ mol(-1), respectively. The pyrolysis process of U.pertusa would be easier than maize straw. And co-firing of the two biomass may be require less external heat input and improve process stability. There were minor kinetic compensation effects between the pre-exponential factors and the activation energy.

Wafer-scale laser pantography: Fabrication of n-metal-oxide-semiconductor transistors and small-scale integrated circuits by direct-write laser-induced pyrolytic reactions

International Nuclear Information System (INIS)

McWilliams, B.M.; Herman, I.P.; Mitlitsky, F.; Hyde, R.A.; Wood, L.L.

1983-01-01

A complete set of processes sufficient for manufacture of n-metal-oxide-semiconductor (n-MOS) transistors by a laser-induced direct-write process has been demonstrated separately, and integrated to yield functional transistors. Gates and interconnects were fabricated of various combinations of n-doped and intrinsic polysilicon, tungsten, and tungsten silicide compounds. Both 0.1-μm and 1-μm-thick gate oxides were micromachined with and without etchant gas, and the exposed p-Si [100] substrate was cleaned and, at times, etched. Diffusion regions were doped by laser-induced pyrolytic decomposition of phosphine followed by laser annealing. Along with the successful manufacture of working n-MOS transistors and a set of elementary digital logic gates, this letter reports the successful use of several laser-induced surface reactions that have not been reported previously

Pyrolysis of the lignocellulose fermentation residue by fixed-bed micro reactor

International Nuclear Information System (INIS)

Wang, Ze; Lin, Weigang; Song, Wenli; Wu, Xuexing

2012-01-01

Thermal gravimetric (TG) analysis was conducted to compare the fundamental pyrolytic behaviors between the lignocellulose fermentation residue (LFR) and three other biomass raw materials. It was found that the TG weight loss curve of LFR appeared very close to the curve of acidified alkaline lignin (AAL), but different to the material of dried distillers grains with solubles (DDGS, also a fermentation residue but obtained from liquor producing process). Pyrolysis of LFR by fixed-bed micro reactor in the range of 430 °C–700 °C was carried out. It was found that the liquid yield had a maximum value at the pyrolytic temperature of 475 °C. The oil phase of the liquid was mainly composed of phenols, and the content of dimethyl phenol and fatty acids decreased with increasing pyrolytic temperature. In the aqueous liquid, besides the most abundant phenol derivatives, small acids and nitrogen containing compounds appeared more. -- Highlights: ► The tense of the paper has been revised. ► The description of the experimental procedure was kept in past tense. ► The expression of ‘fixed bed’ was changed to ‘fixed-bed’.

Metal working oils. Cutting oils, rolling oils, quenching oils, rust preventive oils; Kinzoku kakoyu. Sessakuyu, atsuenyu, yakiireyu, boseiyu

Energy Technology Data Exchange (ETDEWEB)

Koyama, S. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-04-01

With the demand against complicating working techniques for a background, foundations of the consideration for each of the lubricants in future are outlined. 1. Cutting oils: From the standpoint of speeding up and fireproofing, share of water-soluble type has come up to 30-40%. In this type, emulsifying dispersants and preservatives are combined. 2. Rolling oils: According to thinning of the standard thickness of steel plates, pressure of contacting surfaces has come up to 300 kg/mm{sup 2}(max.) and slip speed has increased too. In stainless steel plates, in order to get rid of the heat-streak (baking streak originated from wearing-out of oil film) shifting from neat oil to emulsion type is required. 3. Quenching oils: Following two systems are recent tendencies, the mineral oil system having excellent thermostability or the water system containing polyalkylneglycol etc., but the latter is expected from the viewpoint of fireproofing. 4. Rust preventive oils: As this oils do not aim at the rust prevention for long term, degreasing property is required. 20 refs., 5 figs., 1 tab.

Electrochemical formation and characterization of Au nanostructures on a highly ordered pyrolytic graphite surface

International Nuclear Information System (INIS)

Arroyo Gómez, José J.; Zubieta, Carolina; Ferullo, Ricardo M.; García, Silvana G.

2016-01-01

Graphical abstract: - Highlights: • The electrodeposition of Au on HOPG tends to follow the response predicted for a 3D instantaneous nucleation mechanism in the potential range considered. • By choosing suitable nucleation and growth pulses, one-dimensional deposits were possible, preferentially located on step edges of the HOPG substrate. • Quantum-mechanical calculations confirmed the tendency of Au atoms to join selectively on the HOPG step edges, at the early stages of Au electrodeposition. - Abstract: The electrochemical formation of Au nanoparticles on a highly ordered pyrolytic graphite (HOPG) substrate using conventional electrochemical techniques and ex-situ AFM is reported. From the potentiostatic current transients studies, the Au electrodeposition process on HOPG surfaces was described, within the potential range considered, by a model involving instantaneous nucleation and diffusion controlled 3D growth, which was corroborated by the microscopic analysis. Initially, three-dimensional (3D) hemispherical nanoparticles distributed on surface defects (step edges) of the substrate were observed, with increasing particle size at more negative potentials. The double potential pulse technique allowed the formation of rounded deposits at low deposition potentials, which tend to form lines of nuclei aligned in defined directions leading to 3D ordered structures. By choosing suitable nucleation and growth pulses, one-dimensional (1D) deposits were possible, preferentially located on step edges of the HOPG substrate. Quantum-mechanical calculations confirmed the tendency of Au atoms to join selectively on surface defects, such as the HOPG step edges, at the early stages of Au electrodeposition.

Synthesis of palm oil empty fruit bunch magnetic pyrolytic char impregnating with FeCl3 by microwave heating technique

International Nuclear Information System (INIS)

Mubarak, N.M.; Kundu, A.; Sahu, J.N.; Abdullah, E.C.; Jayakumar, N.S.

2014-01-01

Empty fruit bunch (EFB) is one of the most abundant residues of the Palm oil mill industry in Malaysia. The novel magnetic bio-char was synthesized by single stage microwave heating technique, using EFB in the presence of ferric chloride hexahydrate. The effect of microwave powers, radiation time and impregnation ratio (IR) of ferric chloride hexahydrate to biomass were studied. Also the process parameters such as microwave powers, radiation times and IR were optimized using response surface method. The statistical analysis revealed that the optimum conditions for the high porosity magnetic bio-char production were at 900 W microwave power, 20 min radiation time and 0.5 (FeCl 3 : biomass) impregnation ratio. These newly produced magnetic bio-char have a high surface area of 890 m 2  g −1 and that leads to highly efficient in the removal of methylene blue (MB) with an efficiency of 99.9% from aqueous solution with a maximum adsorption capacity of 265 mg g −1 . - Highlights: • Magnetic bio-char production using discarded material EFB with chemical activation. • Single stage synthesis of magnetic bioc-har via microwave heating was narrated. • Effect of each process parameters on synthesis of magnetic bio-char was elaborated. • Magnetic bio-char has high surface area, high porosity and high adsorption capacity. • Novel magnetic bio-char adds new dimension to the materials as an adsorbent

Oil vulnerability index of oil-importing countries

International Nuclear Information System (INIS)

Gupta, Eshita

2008-01-01

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Oil vulnerability index of oil-importing countries

Energy Technology Data Exchange (ETDEWEB)

Gupta, Eshita [The Energy and Resources Institute, Darbari Seth Block, Habitat Place, New Delhi 110 003 (India)

2008-03-15

This paper assesses the relative oil vulnerability of 26 net oil-importing countries for the year 2004 on the basis of various indicators - the ratio of value of oil imports to gross domestic product (GDP), oil consumption per unit of GDP, GDP per capita and oil share in total energy supply, ratio of domestic reserves to oil consumption, exposure to geopolitical oil market concentration risks as measured by net oil import dependence, diversification of supply sources, political risk in oil-supplying countries, and market liquidity. The approach using the principal component technique has been adopted to combine these individual indicators into a composite index of oil vulnerability. Such an index captures the relative sensitivity of various economies towards developments of the international oil market, with a higher index indicating higher vulnerability. The results show that there are considerable differences in the values of individual indicators of oil vulnerability and overall oil vulnerability index among the countries (both inter and intraregional). (author)

Giant Oil Fields - The Highway to Oil: Giant Oil Fields and their Importance for Future Oil Production

International Nuclear Information System (INIS)

Robelius, Fredrik

2007-01-01

Since the 1950s, oil has been the dominant source of energy in the world. The cheap supply of oil has been the engine for economic growth in the western world. Since future oil demand is expected to increase, the question to what extent future production will be available is important. The belief in a soon peak production of oil is fueled by increasing oil prices. However, the reliability of the oil price as a single parameter can be questioned, as earlier times of high prices have occurred without having anything to do with a lack of oil. Instead, giant oil fields, the largest oil fields in the world, can be used as a parameter. A giant oil field contains at least 500 million barrels of recoverable oil. Only 507, or 1 % of the total number of fields, are giants. Their contribution is striking: over 60 % of the 2005 production and about 65 % of the global ultimate recoverable reserve (URR). However, giant fields are something of the past since a majority of the largest giant fields are over 50 years old and the discovery trend of less giant fields with smaller volumes is clear. A large number of the largest giant fields are found in the countries surrounding the Persian Gulf. The domination of giant fields in global oil production confirms a concept where they govern future production. A model, based on past annual production and URR, has been developed to forecast future production from giant fields. The results, in combination with forecasts on new field developments, heavy oil and oil sand, are used to predict future oil production. In all scenarios, peak oil occurs at about the same time as the giant fields peak. The worst-case scenario sees a peak in 2008 and the best-case scenario, following a 1.4 % demand growth, peaks in 2018

Heavy fuel oil pyrolysis and combustion: kinetics and evolved gases investigated by TGA-FTIR

KAUST Repository

Abdul Jameel, Abdul Gani

2017-08-24

Heavy fuel oil (HFO) obtained from crude oil distillation is a widely used fuel in marine engines and power generation technologies. In the present study, the pyrolysis and combustion of a Saudi Arabian HFO in nitrogen and in air, respectively, were investigated using non-isothermal thermo-gravimetric analysis (TGA) coupled with a Fourier-transform infrared (FTIR) spectrometer. TG and DTG (differential thermo-gravimetry) were used for the kinetic analysis and to study the mass loss characteristics due to the thermal degradation of HFO at temperatures up to 1000°C and at various heating rates of 5, 10 and 20°C/min, in air and N2 atmospheres. FTIR analysis was then performed to study the composition of the evolved gases. The TG/DTG curves during HFO combustion show the presence of three distinct stages: the low temperature oxidation (LTO); fuel decomposition (FD); and high temperature oxidation (HTO) stages. The TG/DTG curves obtained during HFO pyrolysis show the presence of two devolatilization stages similar to that seen in the LTO stage of HFO combustion. Apart from this, the TG/DTG curves obtained during HFO combustion and pyrolysis differ significantly. Kinetic analysis was also performed using the distributed activation energy model, and the kinetic parameter (E) was determined for the different stages of HFO combustion and pyrolysis processes, yielding a good agreement with the measured TG profiles. FTIR analysis showed the signal of CO2 as approximately 50 times more compared to the other pollutant gases under combustion conditions. Under pyrolytic conditions, the signal intensity of alkane functional groups was the highest followed by alkenes. The TGA-FTIR results provide new insights into the overall HFO combustion processes, which can be used to improve combustor designs and control emissions.

Oil risk in oil stocks

NARCIS (Netherlands)

Scholtens, Bert; Wang, L

2008-01-01

We assess the oil price sensitivities and oil risk premiums of NYSE listed oil & gas firms' returns by using a two-step regression analysis under two different arbitrage pricing models. Thus, we apply the Fama and French (1992) factor returns in a study of oil stocks. In all, we find that the return

Effects of deposition conditions on the properties of pyrolytic carbon deposited in a fluidized bed

International Nuclear Information System (INIS)

Lowden, Richard Andrew; Hunn, John D.; Nunn, Stephen D.; Kercher, Andrew K.; Price, Jeffery R.; Jellison, Gerald Earle Jr.

2005-01-01

The high-density, isotropic pyrolytic carbon layer beneath the silicon carbide (IPyC) plays a key role in the irradiation performance of coated particle fuel. The IPyC layer protects the kernel from reactions with chlorine during deposition of the SiC layer, provides structural support for the SiC layer, and protects the SiC from fission products and carbon monoxide. The process conditions used by the Germans to deposit the IPyC coating produced a highly isotropic, but somewhat permeable IPyC coating. The permeability of the IPyC coating was acceptable for use with the dense German UO 2 kernels, but may not be suitable when coating UCO kernels. The UCO kernels are typically more porous and thus have a larger surface area than UO 2 kernels. The lower density and the higher surface area of UCO kernels could make them more susceptible to attack by HCl gas during the silicon carbide (SiC) coating process, which could result in heavy metal dispersion into the buffer and IPyC coatings and a higher level of as-manufactured SiC defects. The relationship between IPyC deposition conditions, permeability, and anisotropy must be understood and the appropriate combination of anisotropy and permeability for particle fuel containing UCO kernels selected. A reference set of processing conditions have been determined from review of historical information and results of earlier coating experiments employing 350 and 500 (micro)m UO 2 kernels. It was decided that a limited study would be conducted, in which only coating gas fraction (CGF) and temperature would be varied. Coatings would be deposited at different rates and with a range of microstructures. Thickness, density, porosity and anisotropy would be measured and permeability evaluated using a chlorine leach test. The results would be used to select the best IPyC coating conditions for use with the available natural enrichment uranium carbide/uranium oxide (NUCO) kernels. The response plots from the investigation of the

Mechanical Properties and Structures of Pyrolytic Carbon Coating Layer in HTR Coated Particle Fuel

International Nuclear Information System (INIS)

Lee, Young Woo; Kim, Young Min; Kim, Woong Ki; Cho, Moon Sung

2009-01-01

The TRISO(tri-isotropic)-coated fuel particle for a HTR(High Temperature gas-cooled Reactor) has a diameter of about 1 mm, composed of a nuclear fuel kernel and four different outer coating layers, consisting of a buffer PyC (pyrolytic carbon) layer, inner PyC layer, SiC layer, and outer PyC layer with different coating thicknesses following a specific fuel design. While the fuel kernel is a source for a heat generation by a nuclear fission of fissile uranium, each of the four coating layers acts as a different role in view of retaining the generated fission products and the other interactions during an in-reactor service. Among these coating layers, PyC properties are scarcely in agreement among various investigators and the dependency of their changes upon the deposition condition is comparatively large due to their additional anisotropic properties. Although a recent review work has contributed to an establishment of relationship between the material properties and QC measurements, the data on the mechanical properties and structural parameters of PyC coating layers remain still unclearly evaluated. A review work on dimensional changes of PyC by neutron irradiation was one of re-evaluative works recently attempted by the authors. In this work, an attempt was made to analyze and re-evaluate the existing data of the experimental results of the mechanical properties, i.e., Young's modulus and fracture stress, in relation with the coating conditions, density and the BAF (Bacon Anisotropy Factor), an important structural parameter, of PyC coating layers obtained from various experiments performed in the early periods of the HTR coated particle development

Structures and electrochemical properties of pyrolytic carbon films infiltrated from gas phase into electro-conductive substrates derived from wood

International Nuclear Information System (INIS)

Ohzawa, Yoshimi; Mitani, Masami; Li, Jianling; Nakajima, Tsuyoshi

2004-01-01

Using the pressure-pulsed chemical vapor infiltration technique, pyrolytic carbon (pyrocarbon) films were deposited into two sorts of conductive porous substrates, that is, the carbonized wood (A) and the TiN-coated wood (B). Structures and electrochemical properties were investigated as the negative electrodes of lithium-ion secondary battery. The electrodes had the three-dimensionally continuous current paths in the pyrocarbon-based anodes without the organic binders and the additional conductive fillers. The pyrocarbon films adhered tightly to the carbonized wood or TiN as current collector. These macro-structures of electrodes were effective in improving the high rate property. The sort of substrates affected the nano-structure of pyrocarbon. The pyrocarbon in sample (A) had the relatively high crystallinity, whereas the pyrocarbon in sample (B) was disordered. The capacity of pyrocarbon in sample (B) was higher than that of sample (A), reflecting the disordered microstructure of pyrocarbon film (B). However, sample (A) showed higher Coulombic efficiency at first cycle (i.e. 87%) than that of sample (B), which would result from the high crystallinity, laminar microstructure and low surface area of pyrocarbon in sample (A)

Binary Hierarchical Porous Graphene/Pyrolytic Carbon Nanocomposite Matrix Loaded with Sulfur as a High-Performance Li-S Battery Cathode.

Science.gov (United States)

Zhang, Hang; Gao, Qiuming; Qian, Weiwei; Xiao, Hong; Li, Zeyu; Ma, Li; Tian, Xuehui

2018-06-06

A N,O-codoped hierarchical porous nanocomposite consisting of binary reduced graphene oxide and pyrolytic carbon (rGO/PC) from chitosan is fabricated. The optimized rGO/PC possesses micropores with size distribution concentrated around 1.1 nm and plenty of meso/macropores. The Brunauer-Emmett-Teller specific surface area is 480.8 m 2 g -1 , and it possesses impressively large pore volume of 2.14 cm 3 g -1 . On the basis of the synergistic effects of the following main factors: (i) the confined space effect in the hierarchical porous binary carbonaceous matrix; (ii) the anchor effects by strong chemical bonds with codoped N and O atoms; and (iii) the good flexibility and conductivity of rGO, the rGO/PC/S holding 75 wt % S exhibits high performance as Li-S battery cathode. Specific capacity of 1625 mA h g -1 can be delivered at 0.1 C (1 C = 1675 mA g -1 ), whereas 848 mA h g -1 can be maintained after 300 cycles at 1 C. Even at high rate of 5 C, 412 mA h g -1 can be restrained after 1000 cycles.

Vegetable oil spills : oil properties and behaviour

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.; Jokuty, P.

2001-01-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs

Vegetable oil spills : oil properties and behaviour

Energy Technology Data Exchange (ETDEWEB)

Fingas, M.; Fieldhouse, B.; Jokuty, P. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div

2001-07-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs.

Converting heavy oils into light oils, etc

Energy Technology Data Exchange (ETDEWEB)

Mony, H

1915-12-22

A process is described for transforming heavy oils obtained by the carbonization of lignites, peats, coals, shales into light oils, and also the heavy oils of mineral and vegetable origin, consisting of heating the heavy oils or tars in the presence of one or more solid substances or liquids suitably chosen to cause the distillation of the oils under atmospheric pressure at an appropriate temperature; solid and liquid substances which favor the production of light products under the influence of heat being added preferably to the oil to be treated before putting it in the retort and before heating, so that light oils are obtained by treatment of the heavy oils in a single operation.

STM observation of a box-shaped graphene nanostructure appeared after mechanical cleavage of pyrolytic graphite

Energy Technology Data Exchange (ETDEWEB)

Lapshin, Rostislav V., E-mail: rlapshin@gmail.com [Solid Nanotechnology Laboratory, Institute of Physical Problems, Zelenograd, Moscow 124460 (Russian Federation); Department of Photosensitive Nano and Microsystems, Moscow Institute of Electronic Technology, Zelenograd, Moscow 124498 (Russian Federation)

2016-01-01

Graphical abstract: - Highlights: • A previously unknown 3D box-shaped graphene (BSG) nanostructure has been detected. • The nanostructure is a multilayer system of parallel nanochannels having quadrangular cross-section. • Typical width of a nanochannel facet makes 25 nm, typical wall/facet thickness is 1 nm. • A mechanism qualitatively explaining the nanostructure formation has been proposed. • Possible applications of the BSG nanostructure are briefly discussed. - Abstract: A description is given of a three-dimensional box-shaped graphene (BSG) nanostructure formed/uncovered by mechanical cleavage of highly oriented pyrolytic graphite (HOPG). The discovered nanostructure is a multilayer system of parallel hollow channels located along the surface and having quadrangular cross-section. The thickness of the channel walls/facets is approximately equal to 1 nm. The typical width of channel facets makes about 25 nm, the channel length is 390 nm and more. The investigation of the found nanostructure by means of a scanning tunneling microscope (STM) allows us to draw a conclusion that it is possible to make spatial constructions of graphene similar to the discovered one by mechanical compression, bending, splitting, and shifting graphite surface layers. The distinctive features of such constructions are the following: simplicity of the preparation method, small contact area between graphene planes and a substrate, large surface area, nanometer cross-sectional sizes of the channels, large aspect ratio. Potential fields of application include: ultra-sensitive detectors, high-performance catalytic cells, nanochannels for DNA manipulation, nanomechanical resonators, electron multiplication channels, high-capacity sorbents for hydrogen storage.

Iranian-Oil-Free Zone and international oil prices

International Nuclear Information System (INIS)

Farzanegan, Mohammad Reza; Raeisian Parvari, Mozhgan

2014-01-01

One of the main elements of economic sanctions against Iran due to its nuclear and military programs is crude oil exportation restrictions in addition to investment in Iranian energy related projects. Senders of such sanction are interested in understanding the impacts of such embargos on international oil prices. We apply unrestricted vector autoregressive (VAR) model, using impulse response functions (IRF) and variance decomposition analysis (VDA) tools with annual data from 1965 to 2012 to analyze the dynamic response of international oil prices to Iranian oil export sanction. Controlling for the supply of non-Iranian oil, the world GDP per capita, and post-Islamic revolution exogenous dummy variables, we show that international oil prices respond negatively and statistically significant to increasing shock in absolute negative changes of the Iranian oil exports – our proxy of Iran oil sanctions – following the first 2 years after shock. The main reason is the positive response of the non-Iranian oil supply to negative shocks in Iranian oil exports, filling the missing supply of Iranian oil in international markets. - Highlights: • We analyze the interconnections between Iranian oil supply and global oil prices. • We use VAR modeling and annual data from 1965 to 2012 for the case of Iran. • There are no inflationary effects of Iranian oil sanction on world oil prices. • Non-Iranian oil supply offsets the missing Iranian oil in the market

Green bio-oil extraction for oil crops

Science.gov (United States)

Zainab, H.; Nurfatirah, N.; Norfaezah, A.; Othman, H.

2016-06-01

The move towards a green bio-oil extraction technique is highlighted in this paper. The commonly practised organic solvent oil extraction technique could be replaced with a modified microwave extraction. Jatropha seeds (Jatropha curcas) were used to extract bio-oil. Clean samples were heated in an oven at 110 ° C for 24 hours to remove moisture content and ground to obtain particle size smaller than 500μm. Extraction was carried out at different extraction times 15 min, 30 min, 45 min, 60 min and 120 min to determine oil yield. The biooil yield obtained from microwave assisted extraction system at 90 minutes was 36% while that from soxhlet extraction for 6 hours was 42%. Bio-oil extracted using the microwave assisted extraction (MAE) system could enhance yield of bio-oil compared to soxhlet extraction. The MAE extraction system is rapid using only water as solvent which is a nonhazardous, environment-friendly technique compared to soxhlet extraction (SE) method using hexane as solvent. Thus, this is a green technique of bio-oil extraction using only water as extractant. Bio-oil extraction from the pyrolysis of empty fruit bunch (EFB), a biomass waste from oil palm crop, was enhanced using a biocatalyst derived from seashell waste. Oil yield for non-catalytic extraction was 43.8% while addition of seashell based biocatalyst was 44.6%. Oil yield for non-catalytic extraction was 43.8% while with addition of seashell-based biocatalyst was 44.6%. The pH of bio-oil increased from 3.5 to 4.3. The viscosity of bio-oil obtained by catalytic means increased from 20.5 to 37.8 cP. A rapid and environment friendly extraction technique is preferable to enhance bio-oil yield. The microwave assisted approach is a green, rapid and environmental friendly extraction technique for the production of bio-oil bearing crops.

Experimental study of pyrolytic boron nitride at high temperature with and without proton and VUV irradiations

International Nuclear Information System (INIS)

Balat-Pichelin, M.; Eck, J.; Heurtault, S.; Glénat, H.

2014-01-01

Highlights: • New results for the high temperature study of pBN in high vacuum for the heat shield of solar probes. • Physico-chemical behavior of pBN studied up to 1700 K with proton and VUV irradiations. • Rather low effect of synergistic aggressions on the microstructure of pBN material. • The α/ε ratio of pBN coating on C/C measured up to 2200 K is 20% lower than for the C/C itself. - Abstract: In the frame of future exploration missions such as Solar Probe Plus (NASA) and PHOIBOS (ESA), research was carried out to study pyrolytic BN material envisaged as coating for their heat shields. The physico-chemical behavior of CVD pBN at very high temperature with or without hydrogen ions and VUV (Vacuum Ultra-Violet) irradiations was studied in high vacuum together with the in situ measurement of the thermal radiative properties conditioning the thermal equilibrium of the heat shield. Experimental results obtained on massive pBN samples are presented through in situ mass spectrometry and mass loss rate, and post-test microstructural characterization by XRD, SEM, AFM and nano-indentation techniques, some of them leading to mechanical properties. It could be concluded that synergistic effect of high temperature, protons and VUV radiation has an impact on the emission of gaseous species, the mass loss rate and the mechanical properties of the material

Effect of mineral oil, sunflower oil, and coconut oil on prevention of hair damage.

Science.gov (United States)

Rele, Aarti S; Mohile, R B

2003-01-01

Previously published results showed that both in vitro and in vivo coconut oil (CNO) treatments prevented combing damage of various hair types. Using the same methodology, an attempt was made to study the properties of mineral oil and sunflower oil on hair. Mineral oil (MO) was selected because it is extensively used in hair oil formulations in India, because it is non-greasy in nature, and because it is cheaper than vegetable oils like coconut and sunflower oils. The study was extended to sunflower oil (SFO) because it is the second most utilized base oil in the hair oil industry on account of its non-freezing property and its odorlessness at ambient temperature. As the aim was to cover different treatments, and the effect of these treatments on various hair types using the above oils, the number of experiments to be conducted was a very high number and a technique termed as the Taguchi Design of Experimentation was used. The findings clearly indicate the strong impact that coconut oil application has to hair as compared to application of both sunflower and mineral oils. Among three oils, coconut oil was the only oil found to reduce the protein loss remarkably for both undamaged and damaged hair when used as a pre-wash and post-wash grooming product. Both sunflower and mineral oils do not help at all in reducing the protein loss from hair. This difference in results could arise from the composition of each of these oils. Coconut oil, being a triglyceride of lauric acid (principal fatty acid), has a high affinity for hair proteins and, because of its low molecular weight and straight linear chain, is able to penetrate inside the hair shaft. Mineral oil, being a hydrocarbon, has no affinity for proteins and therefore is not able to penetrate and yield better results. In the case of sunflower oil, although it is a triglyceride of linoleic acid, because of its bulky structure due to the presence of double bonds, it does not penetrate the fiber, consequently resulting

Chemometric techniques in oil classification from oil spill fingerprinting.

Science.gov (United States)

Ismail, Azimah; Toriman, Mohd Ekhwan; Juahir, Hafizan; Kassim, Azlina Md; Zain, Sharifuddin Md; Ahmad, Wan Kamaruzaman Wan; Wong, Kok Fah; Retnam, Ananthy; Zali, Munirah Abdul; Mokhtar, Mazlin; Yusri, Mohd Ayub

2016-10-15

Extended use of GC-FID and GC-MS in oil spill fingerprinting and matching is significantly important for oil classification from the oil spill sources collected from various areas of Peninsular Malaysia and Sabah (East Malaysia). Oil spill fingerprinting from GC-FID and GC-MS coupled with chemometric techniques (discriminant analysis and principal component analysis) is used as a diagnostic tool to classify the types of oil polluting the water. Clustering and discrimination of oil spill compounds in the water from the actual site of oil spill events are divided into four groups viz. diesel, Heavy Fuel Oil (HFO), Mixture Oil containing Light Fuel Oil (MOLFO) and Waste Oil (WO) according to the similarity of their intrinsic chemical properties. Principal component analysis (PCA) demonstrates that diesel, HFO, MOLFO and WO are types of oil or oil products from complex oil mixtures with a total variance of 85.34% and are identified with various anthropogenic activities related to either intentional releasing of oil or accidental discharge of oil into the environment. Our results show that the use of chemometric techniques is significant in providing independent validation for classifying the types of spilled oil in the investigation of oil spill pollution in Malaysia. This, in consequence would result in cost and time saving in identification of the oil spill sources. Copyright © 2016. Published by Elsevier Ltd.

Effects of carbon dioxide on pyrolysis of peat

International Nuclear Information System (INIS)

Lee, Jechan; Yang, Xiao; Song, Hocheol; Ok, Yong Sik; Kwon, Eilhann E.

2017-01-01

This study focuses on the mechanistic understanding of effects of CO 2 on pyrolysis of peat. To do this, three pyrolytic products (i.e., syngas: H 2 and CO, pyrolytic oil (tar), and biochar) were characterized. Thermal cracking of volatile organic carbons (VOCs) generated from pyrolysis of peat was enhanced in the presence of CO 2 . Besides the enhanced thermal cracking of VOCs, unknown reaction between CO 2 and VOCs was also identified. Accordingly, CO 2 played a role in enhancing syngas production and in reducing tar formation in pyrolysis of peat. This study also reveals that peat-biochar produced in CO 2 exhibited a larger surface area than that produced in N 2 . The results shown in this paper would be used for various applications such as energy recovery from peat using a potent greenhouse gas (for example, CO 2 ). - Highlights: • More CO can be produced from pyrolysis of peat in CO 2 than in N 2 . • Less amount of tar produced from pyrolysis of peat in CO 2 than in N 2 . • Surface area of peat-biochar made in CO 2 is larger than that made in N 2 . • CO 2 can modify the quantity/quality of pyrolytic products from peat.

21 CFR 172.861 - Cocoa butter substitute from coconut oil, palm kernel oil, or both oils.

Science.gov (United States)

2010-04-01

... kernel oil, or both oils. 172.861 Section 172.861 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT... substitute from coconut oil, palm kernel oil, or both oils. The food additive, cocoa butter substitute from coconut oil, palm kernel oil, or both oils, may be safely used in food in accordance with the following...

Quantification of rice bran oil in oil blends

Energy Technology Data Exchange (ETDEWEB)

Mishra, R.; Sharma, H. K.; Sengar, G.

2012-11-01

Blends consisting of physically refined rice bran oil (PRBO): sunflower oil (SnF) and PRBO: safflower oil (SAF) in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil. (Author) 23 refs.

Oil spills

International Nuclear Information System (INIS)

Katsouros, M.H.

1992-01-01

The world annually transports 1.7 billion tons of oil by sea, and oil spills, often highly concentrated discharges, are increasing from a variety of sources. The author discusses sources of oils spills: natural; marine transportation; offshore oil production; atmospheric sources; municipal industrial wastes and runoff. Other topics include: the fate of the spilled oil; the effects of the oil; the response to oil spills; and prevention of oil spills. 30 refs., 1 fig., 4 tabs

Evaluation of Melanogenesis in A-375 Cells in the Presence of DMSO and Analysis of Pyrolytic Profile of Isolated Melanin

Science.gov (United States)

Chodurek, Ewa; Orchel, Arkadiusz; Orchel, Joanna; Kurkiewicz, Sławomir; Gawlik, Natalia; Dzierżewicz, Zofia; Stępień, Krystyna

2012-01-01

The increase of a skin malignant melanoma (melanoma malignum) incidence in the world has been observed in recent years. The tumour, especially in advanced stadium with metastases, is highly resistant to conventional treatment. One of the strategies is to modulate melanogenesis using chemical compounds. In this study, the processes of differentiation and melanogenesis induced by dimethylsulfoxide (DMSO) in human melanoma cells (A-375) were investigated. Natural melanin isolated from A-375 melanoma cell line treated with 0.3% DMSO was analyzed by pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS) method. The products derived from pheomelanin have not been stated in the pyrolytic profile of analyzed melanin. Within all products derived from eumelanins, 1,2-benzenediol has been predominated. It has been shown that in the melanoma cells stimulated with 0.3% and 1% DMSO, the increase of transcriptional activity of the tyrosinase gene took place. It was accompanied by the rise of tyrosinase activity and an accumulation of melanin in the cells. The better knowledge about the structure of melanins can contribute to establish the uniform criteria of malignant melanoma morbidity risk. PMID:22654640

Biomass pyrolysis: use of some agricultural wastes for alternative fuel production

International Nuclear Information System (INIS)

Kimura, Lygia Maestri; Santos, Larissa Cardoso; Vieira, Paula Fraga; Parreira, Priciane Martins; Henrique, Humberto Molinar

2009-01-01

The use of biomass for energy generation has aroused great attention and interest because of the global climate changes, environmental pollution and reduction of availability of fossil energy. This study deals with pyrolysis of four agricultural wastes (sawdust, sugarcane straw, chicken litter and cashew nut shell) in a fixed bed pyrolytic reactor. The yields of char, liquid and gas were quantified at 300, 400, 500, 600 and 700 deg C and the temperature and pressure effects were investigated. Pyrolytic liquids produced were separated into aqueous and oil phases. XRF spectroscopy was used for qualitative and quantitative elemental analysis of the liquids and solids produced at whole temperature range. Calorific value analysis of liquids and solids were also performed for energy content evaluation. Experimental results showed sawdust, sugarcane straw and cashew nut waste have very good potential for using in pyrolysis process for alternative fuel production. (author)

Hydroprocesssing of light gas oil - rape oil mixtures

Energy Technology Data Exchange (ETDEWEB)

Walendziewski, Jerzy; Stolarski, Marek; Luzny, Rafal; Klimek, Bartlomiej [Faculty of Chemistry, Wroclaw University of Technology, ul. Gdanska 7/9, 50-310 Wroclaw (Poland)

2009-05-15

Two series of experiments of hydroprocessing of light gas oil - rape oil mixtures were carried out. The reactor feed was composed of raw material: first series - 10 wt.% rape oil and 90 wt.% of diesel oil; second series - 20 wt.% rape oil and 80 wt.% of diesel oil. Hydroprocessing of both mixtures was performed with the same parameter sets, temperature (320, 350 and 380 C), hydrogen pressure 3 and 5 MPa, LHSV = 2 h{sup -} {sup 1} and hydrogen feed ratio of 500 Nm{sup 3}/m{sup 3}. It was stated that within limited range it is possible to control vegetable oil hydrogenolysis in the presence of light gas oil fraction (diesel oil boiling range) through the proper selection of the process parameters. Hydrogenolysis of ester bonds and hydrogenation of olefinic bonds in vegetable oils are the main reactions in the process. Basic physicochemical properties of the obtained hydroprocessed products are presented. (author)

Oil Spills

Science.gov (United States)

... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ... up. How Oil Harms Animals and Plants in Marine Environments In general, oil spills can affect animals and plants in two ways: from the oil ...

Oil/gas collector/separator for underwater oil leaks

Energy Technology Data Exchange (ETDEWEB)

Henning, C.D.

1992-12-31

This invention is comprised of an oil/gas collector/separator for recovery of oil leaking, for example, from an offshore or underwater oil well. The separator is floated over the point of the leak and tethered in place so as to receive oil/gas floating, or forced under pressure, toward the water surface from either a broken or leaking oil well casing, line, or sunken ship. The separator is provided with a downwardly extending skirt to contain the oil/gas which floats or is forced upward into a dome wherein the gas is separated from the oil/water, with the gas being flared (burned) at the top of the dome, and the oil is separated from water and pumped to a point of use. Since the density of oil is less than that of water it can be easily separated from any water entering the dome.

Growth and characterization of stoichiometric BCN films on highly oriented pyrolytic graphite by radiofrequency plasma enhanced chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Mannan, Md. Abdul, E-mail: amannan75@yahoo.co [Department of Chemistry and Applied Chemistry, Faculty of Science and Engineering, Saga University, 1 Honjo, Saga 840-8502 (Japan); Synchrotron Radiation Research Unit, Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Noguchi, Hideyuki; Kida, Tetsuya; Nagano, Masamitsu [Department of Chemistry and Applied Chemistry, Faculty of Science and Engineering, Saga University, 1 Honjo, Saga 840-8502 (Japan); Hirao, Norie; Baba, Yuji [Synchrotron Radiation Research Unit, Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan)

2010-05-31

Hexagonal boron carbonitride (h-BCN) hybrid films have been synthesized on highly oriented pyrolytic graphite by radiofrequency plasma enhanced chemical vapor deposition using tris-(dimethylamino)borane as a single-source molecular precursor. The films were characterized by X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS) and Raman spectroscopic measurements. XPS measurement showed that the B atoms were bonded to C and N atoms to form the sp{sup 2}-B-C-N atomic hybrid chemical environment. The atomic composition estimated from the XPS of the typical sample was found to be almost B{sub 1}C{sub 1}N{sub 1}. NEXAFS spectra of the B K-edge and the N K-edge had the peaks due to the {pi}* and {sigma}* resonances of sp{sup 2} hybrid orbitals implying the existence of the sp{sup 2} hybrid configurations of h-BCN around the B atoms. The G band at 1592 and D band at 1352 cm{sup -1} in the Raman spectra also suggested the presence of the graphite-like sp{sup 2}-B-C-N atomic hybrid bonds. The films consisted of micrometer scale crystalline structure of around 10 {mu}m thick has been confirmed by the field emission scanning electron microscopy.

27 CFR 21.98 - Bone oil (Dipple's oil).

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bone oil (Dipple's oil....98 Bone oil (Dipple's oil). (a) Color. The color shall be a deep brown. (b) Distillation range. When... below 90 °C. (c) Pyrrol reaction. Prepare a 1.0 percent solution of bone oil in 95 percent alcohol...

Compositional modification of crude oil during oil recovery

Energy Technology Data Exchange (ETDEWEB)

Zhu, Yangming; Weng, Huanxin [Department of Earth Sciences, Zhejiang University, Hangzhou 310027 (China); Chen, Zulin; Chen, Qi [Petroleum Geochemistry Research Center, Jianghan Petroleum University, Jingzhou, Hubei (China)

2003-05-01

Ten crude oils from two recovery stages spanning 5-10-year interval of five productive wells in the Tarim Basin, northwest China were analyzed for their compositional modification during production process. Significant compositional changes in polar and nonpolar fractions between the previous oil samples and the latter ones were noted at both bulk and molecular level. The latter oil samples appear to contain more aromatic fraction and less asphaltenes and resin, and their gas chromatography (GC) data for whole oil show reduced alkanes with low molecular weight and enhanced high homologue relative to the previous oil samples. Compared with the oils collected from the previous recovery stage, the concentration of basic type of nitrogen-containing compounds and organic acids in oils from the latter recovery stage have a reducing trend, suggesting the occurrence of interaction between crude oil and reservoir rock.

Oil and influence: the oil weapon examined

Energy Technology Data Exchange (ETDEWEB)

Maull, H

1975-01-01

The term ''oil weapon'' as used here signifies any manipulation of the price and/or supply of oil by exporting nations with the intention of changing the political behavior of the consumer nations. The political potential of the oil price is fairly restricted so, in effect, the supply interruptions are of prime concern. Manipulating price does, in principle, offer the possibilities of both conferring rewards and inflicting sanctions. Oil could be sold on preferential prices and terms. A precondition for using the oil weapon successfully would be the ability to cause real and serious damage to the consumer countries. Four damaging potentials for using the oil weapon could include its application by: (1) one producer against one consumer; (2) one producer against all consumers; (3) a group of producers against one consumer; and (4) by a group of producers against all consumers. It is concluded that the oil weapon will continue to be a force in the international system. (MCW)

Biochemically enhanced oil recovery and oil treatment

Science.gov (United States)

Premuzic, Eugene T.; Lin, Mow

1994-01-01

This invention relates to the preparation of new, modified organisms, through challenge growth processes, that are viable in the extreme temperature, pressure and pH conditions and salt concentrations of an oil reservoir and that are suitable for use in microbial enhanced oil recovery. The modified microorganisms of the present invention are used to enhance oil recovery and remove sulfur compounds and metals from the crude oil.

Research of losses of oil oil and mineral oil at transportation and storage

International Nuclear Information System (INIS)

Akzhigitov, A.S.

2005-01-01

Full text : All way of hydrocarbonic raw material from a mouth of oil wells up to the consumer is accompanied by losses which occur as a result of evaporation, outflow and change of quality. Therefore preservation of quantity and quality of oil and mineral oil during transportation and storages is the major not only economic, but also an ecological problem. The facilitated fractional structure, the big maintenance concern to prominent features of the majority oil from underground salts adjournment Prycaspi in them of the easy hydrocarbons, the raised gas factor in conditions of deposits and presence in structure of gases, except for hydrocarbons and sour a component, - hydrogen sulphide, carbonic gas, etc. The superficial tests stabilized on phase structure oil depending on conditions of preparation for external transport and the subsequent processing can contain this or that quantity of residual hydrogen sulphide, easy hydrocarbons and the lowest sulfhydrates. For change of temperature and external pressure, during transportation and storage the part of easy hydrocarbons and not hydrocarbonic connections (sulfur organic) can be allocated from oil in a gaseous phase and in case of hit in an atmosphere sharply worsens ecology. In the Western Kazakhstan during the years period the temperature of air sometimes reaches up to 40-45 degrees. As is known, at such temperature there is a strengthened warming up of the open surface of oil tanks, that finally leads to increase evaporation easy oil and oil hydrocarbons. With this purpose experiences by quantitative definition evaporation lungs oil and petromixes of the Western Kazakhstan were spent. As a result of the lead works it is found out, that the size of losses at the given fixed temperature depends on evaporation by nature, fractional and hydrocarbonic structures of oil

Influence of oil and mineral characteristics on oil-mineral interaction

International Nuclear Information System (INIS)

Wood, P.A.; Lunel, T.; Daniel, F.; Swannell, R.; Lee, K.; Stoffyn-Egli, P.

1998-01-01

A laboratory study was conducted to simulate the process of oil-mineral interaction in seawater. Thirteen different crudes, emulsions and oil products were used in the study. The objective was to improve the fundamental understanding of the characteristics of oils and minerals that influence the process. The findings of an initial phase of studies based on the swirling flask and marine simulation procedures were also described. Oil content associated with flocs to oil and mineral characteristics were discussed. Emulsions were prepared at 10 degrees C by vigorously mixing the oil with excess artificial seawater in a Kilner jar using a high shear homogenizer. Topped oils were prepared by distillation to 250 degrees C. The biodegraded oil was prepared from the topped crude oil. Biodegradation was achieved over a 28 day period using natural seawater and naturally occurring hydrocarbon degraders. The relationships between oil concentration, oil density and mineral exchange capacity were determined. The study showed that greater oil concentrations in the water column could be expected with (1) the presence of mineral fines, (2) minerals with greater cation exchange rates, (3) minerals with finer sizes, and (4) oils of lower viscosity and density. It was determined that in coastal waters the viscosity of the oil/emulsion will likely be the main factor affecting oil-mineral interactions. The viscosity limit for allowing oil fines interaction is likely to be dependent on the energy in the coastal zone affected by the oil pollution. 18 refs., 5 tabs., 13 figs

Dynamic correlation between stock market and oil prices: The case of oil-importing and oil-exporting countries

OpenAIRE

Filis, George; Degiannakis, S.; Floros, C.

2011-01-01

The paper investigates the time-varying correlation between stock market prices and oil prices for oil-importing and oil-exporting countries. A DCC-GARCH-GJR approach is employed to test the above hypothesis based on data from six countries; Oil-exporting: Canada, Mexico, Brazil and Oil-importing: USA, Germany, Netherlands. The contemporaneous correlation results show that i) although time-varying correlation does not differ for oil-importing and oil-exporting economies, ii) the correlation i...

What is behind the increase in oil prices? Analyzing oil consumption and supply relationship with oil price

International Nuclear Information System (INIS)

Gallo, Andres; Mason, Paul; Shapiro, Steve; Fabritius, Michael

2010-01-01

The continuing increases in oil prices have renewed the argument over the real culprits behind these movements. The growth in demand for oil in international markets, especially from the United States and China, is often identified as the main source of consumption pressure on prices, and thus the upward trend in oil prices. This paper uses unit root tests with two endogenous breaks to analyze the characteristics of oil prices, production, and consumption for several countries. By taking into account structural breaks, we find that many countries' oil consumption and oil prices are stationary, while other countries' are not. We also perform causality tests to determine the direction of any possible relationship between oil price and oil consumption and production. Our statistical analysis reveals that production variables cause oil prices, while oil prices tend to cause consumption. As a result, we claim that the blame for the recent fluctuations in oil prices is more appropriately associated with supply factors, not consumption influences. (author)

Oil flow in deep waters: comparative study between light oils and heavy oils

Energy Technology Data Exchange (ETDEWEB)

Andreolli, Ivanilto [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2009-12-19

Ultra deeper waters fields are being exploited due to technological development. Under this scenario, the flow design is accomplished through pipelines subjected to low temperature and high pressure. Moreover, these flow lines are usually long causing a fast fluid cooling, which may affect flow assurance in some cases. Problems during topsides production plant's restart might occur if the oil is viscous and even in steady state a significant different behavior can be noticed, if compared to a less viscous oil. A comparison between light and heavy oil through a case study with the objective to show some heavy oil flow particularities is the purpose of this paper. Permanent and transient analyses for a specific geometry are presented. The results showed that thermal and proper viscosity modeling are required for heavy oil flow, differently from that of light oil flow, due to the exponential viscosity dependence to temperature and because the predominant laminar regime. In addition, on heavier and heavier oil flow systems, it is essential to consider exportation system's restart. (author)

Japan FRI research activities on oil tank/spilled oil fire

International Nuclear Information System (INIS)

Koseki, Hiroshi

1992-01-01

Introduction of research activities on oil tank/spilled oil fire at FRI, Japan is done. FRI has a long history of studying oil tank and spilled oil fires. Many large oil fire tests were done. The purpose of these studies is different with research of response of oil spill, but the accumulation of this knowledge is useful for conducting elimination of spilled oil on the sea with burning. Therefore to do collaboration with fire science research groups, such as FRI is useful for future activities for response to oil spills

Yield and characteristics of shale oil from the retorting of oil shale and fine oil-shale ash mixtures

International Nuclear Information System (INIS)

Niu, Mengting; Wang, Sha; Han, Xiangxin; Jiang, Xiumin

2013-01-01

Highlights: • The whole formation process of shale oil might be divided into four stages. • Higher ash/shale mass ratio intensified the cracking and coking of shale oil. • Ash/shale ratio of 1:2 was recommended for oil shale fluidized bed retort with fine oil-shale ash as solid heat carrier. - Abstract: For exploring and optimizing the oil shale fluidized bed retort with fine oil-shale ash as a solid heat carrier, retorting experiments of oil shale and fine oil-shale ash mixtures were conducted in a lab-scale retorting reactor to investigate the effects of fine oil-shale ash on shale oil. Oil shale samples were obtained from Dachengzi Mine, China, and mixed with fine oil-shale ash in the ash/shale mass ratios of 0:1, 1:4, 1:2, 1:1, 2:1 and 4:1. The experimental retorting temperature was enhanced from room temperature to 520 °C and the average heating rate was 12 °C min −1 . It was found that, with the increase of the oil-shale ash fraction, the shale oil yield first increased and then decreased obviously, whereas the gas yield appeared conversely. Shale oil was analyzed for the elemental analysis, presenting its atomic H/C ratio of 1.78–1.87. Further, extraction and simulated distillation of shale oil were also conducted to explore the quality of shale oil. As a result, the ash/shale mixing mass ratio of 1:2 was recommended only for the consideration of increasing the yield and quality of shale oil

Palm Oil

Science.gov (United States)

Palm oil is obtained from the fruit of the oil palm tree. Palm oil is used for preventing vitamin A deficiency, cancer, ... blood pressure, high cholesterol, and cyanide poisoning. Palm oil is used for weight loss and increasing the ...

Diesel oil

Science.gov (United States)

Oil ... Diesel oil ... Diesel oil poisoning can cause symptoms in many parts of the body. EYES, EARS, NOSE, AND THROAT Loss of ... most dangerous effects of hydrocarbon (such as diesel oil) poisoning are due to inhaling the fumes. NERVOUS ...

Shale-oil-derived additives for fuel oils

International Nuclear Information System (INIS)

Raidma, E.; Leetsman, L.; Muoni, R.; Soone, Y.; Zhiryakov, Y.

2002-01-01

Studies have shown that the oxidation, wearing, and anticorrosive properties of shale oil as an additive to liquid fuels and oils enable to improve the conditions of their use. Studies conducted by Institute of Oil Shale have shown that it is possible, on the basis of shale oil produced by Viru Keemia Grupp AS (Viru Chemistry Group Ltd.) and, particularly, on the basis of its fractions 230-320 and 320-360 deg C to produce efficient and stable additives for liquid fuels to improve their combustion and storage properties. In the production of additives from shale oil the prerequisite taken into account is its complexity of composition and high concentration of neutral and phenolic oxygen compounds. Additives produced from shale oil have multifunctional properties which enable to improve operational data of liquid fuels and to increase the power of diesel engines and boilers. (author)

Investigating oiled birds from oil field waste pits

International Nuclear Information System (INIS)

Gregory, D.G.; Edwards, W.C.

1991-01-01

Procedures and results of investigations concerning the oiling of inland raptors, migratory water-fowl and other birds are presented. Freon washings from the oiled birds and oil from the pits were analyzed by gas chromatography. In most instances the source of the oil could be established by chromatographic procedures. The numbers of birds involved (including many on the endangered species list) suggested the need for netting or closing oil field waste pits and mud disposal pits. Maintaining a proper chain of custody was important

Mathematical modeling of the fermentation of acid-hydrolyzed pyrolytic sugars to ethanol by the engineered strain Escherichia coli ACCC 11177.

Science.gov (United States)

Chang, Dongdong; Yu, Zhisheng; Islam, Zia Ul; Zhang, Hongxun

2015-05-01

Pyrolysate from waste cotton was acid hydrolyzed and detoxified to yield pyrolytic sugars, which were fermented to ethanol by the strain Escherichia coli ACCC 11177. Mathematical models based on the fermentation data were also constructed. Pyrolysate containing an initial levoglucosan concentration of 146.34 g/L gave a glucose yield of 150 % after hydrolysis, suggesting that other compounds were hydrolyzed to glucose as well. Ethyl acetate-based extraction of bacterial growth inhibitors with an ethyl acetate/hydrolysate ratio of 1:0.5 enabled hydrolysate fermentation by E. coli ACCC 11177, without a standard absorption treatment. Batch processing in a fermenter exhibited a maximum ethanol yield and productivity of 0.41 g/g and 0.93 g/L·h(-1), respectively. The cell growth rate (r x ) was consistent with a logistic equation [Formula: see text], which was determined as a function of cell growth (X). Glucose consumption rate (r s ) and ethanol formation rate (r p ) were accurately validated by the equations [Formula: see text] and [Formula: see text], respectively. Together, our results suggest that combining mathematical models with fermenter fermentation processes can enable optimized ethanol production from cellulosic pyrolysate with E. coli. Similar approaches may facilitate the production of other commercially important organic substances.

Toxicities of Selected Essential Oils, Silicone Oils, and Paraffin Oil against the Common Bed Bug (Hemiptera: Cimicidae).

Science.gov (United States)

Zha, Chen; Wang, Changlu; Li, Andrew

2018-02-09

The common bed bug [Cimex lectularius L. (Hemiptera: Cimicidae)] and tropical bed bug [Cimex hemipterus F. (Hemiptera: Cimicidae)] resurged in the United States and many other countries over the past decades. The need for safe and effective bed bug control products propelled the development of numerous 'green insecticides', mostly with essential oils listed as active ingredients. Various inorganic and organic oils also were used for bed bug management. However, there are no published studies on their toxicities against bed bugs. In this study, we screened 18 essential oils, three silicone oils, and paraffin oil (C5-20 paraffins) for their toxicities against bed bugs. All the oils exhibited insecticidal activity in topical assays. Their toxicities varied significantly; all of the evaluated essential oils were less effective than silicone oils and paraffin oil. The LD50 values of the most effective essential oil (blood orange), paraffin oil, and the most effective silicone oil (dodecamethylpentasiloxane) are 0.184 ± 0.018, 0.069 ± 0.012, and 0.036 ± 0.005 mg per bug, respectively. Direct spray of 1% water solution of 3-[hydroxy (polyethyleneoxy) propyl] heptamethyltrisiloxane, the only silicone oil that mixes well with water, resulted in 92% bed bug mortality after 1 d. Results of this study indicate silicone oils and paraffin oil have the potential to be used as safer alternative bed bug control materials. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Oil on seawater

International Nuclear Information System (INIS)

Boerresen, J.A.

1993-01-01

The present book discusses the effects of oil spills at sea. Topics covered are as follow: Petroleum properties; oil spills at sea; harmfulness of oil spills; effects from acute oil spills; experience of oil spills; oil spill contingency planning in Norway; oil spill protecting equipment and methods; emergency of unloading equipment. 252 refs., 86 figs., 54 tabs

Method of removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues

Energy Technology Data Exchange (ETDEWEB)

Palmquist, F T.E.

1949-09-08

A method is described for removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues by centrifuging in the presence of oil-dissolving and paraffin-precipitating solvents, by which the precipitated paraffin is made to pass through an indifferent auxiliary liquid, in which a removal of oil takes place, characterized in that as auxiliary liquid is used a liquid or mixture of liquids whose surface tension against the oil solution is sufficiently low for the paraffin to pass the layer of auxiliary liquid in the form of separate crystals.

Asian oil demand

International Nuclear Information System (INIS)

Fesharaki, F.

2005-01-01

This conference presentation examined global oil market development and the role of Asian demand. It discussed plateau change versus cyclical movement in the global oil market; supply and demand issues of OPEC and non-OPEC oil; if high oil prices reduce demand; and the Asian oil picture in the global context. Asian oil demand has accounted for about 50 per cent of the global incremental oil market growth. The presentation provided data charts in graphical format on global and Asia-Pacific incremental oil demand from 1990-2005; Asia oil demand growth for selected nations; real GDP growth in selected Asian countries; and, Asia-Pacific oil production and net import requirements. It also included charts in petroleum product demand for Asia-Pacific, China, India, Japan, and South Korea. Other data charts included key indicators for China's petroleum sector; China crude production and net oil import requirements; China's imports and the share of the Middle East; China's oil exports and imports; China's crude imports by source for 2004; China's imports of main oil products for 2004; India's refining capacity; India's product balance for net-imports and net-exports; and India's trade pattern of oil products. tabs., figs

Brine crude oil interactions at the oil-water interface

DEFF Research Database (Denmark)

Chakravarty, Krishna Hara; Fosbøl, Philip Loldrup; Thomsen, Kaj

2015-01-01

The impact of brine salinity and its ionic composition on oil displacement efficiency has been investigated extensively in recent years due to the potential of enhanced oil recovery (EOR). Wettability alterations through relative interactions at the mineral surface have been the basis of proposed...... in enhancing oil emulsion formation by increasing interactions between polar acids and brine solutions. The results propose the potential use of HPO42- ions in reservoirs having inactive mineral surfaces. The relative oil affinity of different ions including K+, Na+, Mg2+, and Ca2+ (cations), and Cl-, SO42...... and thus reduces the interfacial viscoelasticity of the trapped oil. These results show significant correlation between oil emulsion formation and increased oil recovery. Copyright 2015; Society of Petroleum Engineers...

Detection of argan oil adulterated with vegetable oils: New markers

Energy Technology Data Exchange (ETDEWEB)

Ourrach, I.; Rada, M.; Perez-Camino, M. C.; Benaissa, M.; Guinda, A

2012-07-01

This work aims to contribute to controlling the authenticity of pure argan oil, a valuable Moroccan product. Fatty acids, hydrocarbon fraction, 3,5-stigmastadiene, the alkyl esters of fatty acids, chlorophyllic pigments and physical properties such as viscosity, density and refractive index were studied in order to detect the adulteration of argan oil with edible vegetable oils. The results found in this study show that 3,5-stigmastadiene, kaurene and pheophytin-a can be used as possible new markers for argan oil blends of up to 5% with refined, sunflower and virgin olive oils. Due to the similarity of the fatty acid compositions of the edible oils studied and argan oil, fatty acids can be employed as markers for the detection of argan oil adulteration at levels higher than 10%. Among the physical properties studied, the refractive index shows significant differences for sunflower oil and its blend at 10% with argan oil. (Author) 35 refs.

Modification of Oil Palm Plantation Wastes as Oil Adsorbent for Palm Oil Mill Effluent (POME)

International Nuclear Information System (INIS)

Noraisah Jahi; Ling, E.S.; Rizafizah Othaman; Suria Ramli

2015-01-01

This research was conducted to modify oil palm solid wastes chemically to become oil adsorbent for palm oil mill effluent (POME). The purpose of modification on oil palm leaves (OPL) and oil palm frond (OPF) was to change the hydrophilic nature to a more hydrophobic character. This study also exploited the production of sorbent materials with high efficiency in the oil uptake for POME from OPL and OPF. Chemical modification was carried out using 200 mL of 1.0 M lauric acid solution for 6 hrs at room temperature. The modified OPL and OPF were preceded to adsorption test for POME and the capacity of oil adsorbed was compared between them. FTIR analysis supported the modification to occur with the increase in a peak of C-H group and the presence of C=O originated from lauric acid structure chain. The hydrophobicity of modified OPL and OPF samples was supported by XRD and contact angle analysis with modified OPL became more hydrophobic than the modified OPF, which had been 38.15 % and 24.67 % respectively. Both the analyses proved that the result from the oil adsorption test on POME showed the presence of a new peak attribute at C=C stretching of aromatics for the oil in POME proved that it was attached on the sorbent materials. Based on SEM analysis, the perforated and rough surface had been observed on modified OPL and OPF samples because oil layers on OPL and OPF surfaces were observed on the modified samples after the adsorption test. All the analyses in the study agreed that the results from oil adsorption test showed that the modified OPL had higher adsorption capacity than the modified OPF with the percentage of oil uptake at 83.74 % and 39.84 % respectively. The prepared adsorbent showed the potential to be used as a low-cost adsorbent in oil for POME. (author)

New pyrolytic and spectroscopic data on Orgueil and Murchison insoluble organic matter: A different origin than soluble?

Science.gov (United States)

Remusat, Laurent; Derenne, Sylvie; Robert, François; Knicker, Heike

2005-08-01

Pyrolysis with and without tetramethylammonium hydroxide (TMAH), vacuum pyrolysis, and solid state 15N nuclear magnetic resonance (NMR) were used to examine the macromolecular insoluble organic matter (IOM) from the Orgueil and Murchison meteorites. Conventional pyrolysis reveals a set of poorly functionalized aromatic compounds, ranging from one to four rings and with random methyl substitutions. These compounds are in agreement with spectroscopic and pyrolytic results previously reported. For the first time, TMAH thermochemolysis was used to study extraterrestrial material. The detection of aromatics bearing methyl esters and methoxy groups reveals the occurrence of ester and ether bridges between aromatic units in the macromolecular network. No nitrogen-containing compounds were detected with TMAH thermochemolysis, although they are a common feature in terrestrial samples. Along with vacuum pyrolysis results, thermochemolysis shows that nitrogen is probably sequestered in condensed structures like heterocyclic aromatic rings, unlike oxygen, which is mainly located within linkages between aromatic units. This is confirmed by solid state 15N NMR performed on IOM from Orgueil, showing that nitrogen is present in pyrrole, indole, and carbazole moieties. These data show that amino acids are neither derived from the hydrolysis of IOM nor from a common precursor. In order to reconcile the literature isotopic data and the present molecular results, it is proposed that aldehydes and ketones (1) originated during irradiation of ice in space and (2) were then mobilized during the planetesimal hydrothermalism, yielding the formation of amino acids. If correct, prebiotic molecules are the products of the subsurface chemistry of planetesimals and are thus undetectable through astronomical probes.

Electrochemical modification of a pyrolytic graphite sheet for improved negative electrode performance in the vanadium redox flow battery

Science.gov (United States)

Kabir, Humayun; Gyan, Isaiah O.; Francis Cheng, I.

2017-02-01

The vanadium redox flow battery is a promising technology for buffering renewable energies. It is recognized that negative electrode is the limitation in this device where there are problems of slow heterogeneous electron transfer (HET) of V3+/2+ and parasitic H2 evolution. Any methods aimed at addressing one of these barriers must assess the effects on the other. We examine electrochemical enhancement of a common commercially available material. Treatment of Panasonic pyrolytic graphite sheets is through oxidation at 2.1 V vs. Ag/AgCl for 1 min in 1 M H2SO4. This increases the standard HET rate for V3+/2+ from 3.2 × 10-7 to 1 × 10-3 cm/s, one of the highest in literature and shifts voltammetric reductive peak potential from -1.0 V to -0.65 V in 50 mM V3+ in 1 M H2SO4. Infrared analysis of the surfaces indicates formation of Csbnd OH, Cdbnd O, and Csbnd O functionalities. These groups catalyze HET with V3+/2+ as hypothesized by Skyllas-Kasacos. Also of significance is that electrode modification decreases the fraction of the current directed towards H2 evolution. This proportion decreases by two orders of a magnitude from 12% to 0.1% as measured at the respective voltammetric peak potentials of -1.0 V (pristine) and -0.65 V (modified).

The oil and oil services industry international context 2008

International Nuclear Information System (INIS)

Serbutoviez, S.; Silva, C.

2008-11-01

Oil companies rarely do their own major work within the framework of their investments or in the operation of their facilities. They most often act as project coordinators, thereby opening up a vast market for equipment, services and engineering, involving many companies of widely-varying sizes, which constitute the oil services industry. This document provides a panorama of the international oil context in three distinct parts, for 2007, for the first three quarters of 2008, and aspects of trends for 2009. - The first part is devoted to a rapid description of the oil context and the economic environment in which it is evolving. - The second part examines the evolution of world investment in exploration-production (E and P) activities, distinguishing the investments made by oil and oil product/service companies throughout the E and P chain from the more targeted ones of three specific sectors: seismic, drilling and the construction of offshore production equipment. These markets are observed exclusively for oil product/service companies. - The last part is devoted to investments in the refining sector, focusing on the changes in the fundamentals, particularly the equilibrium between refining capacities and medium- term oil demand. This latter analysis involves both oil and oil product/service companies. (authors)

The functioning of the oil market during an oil crisis

International Nuclear Information System (INIS)

Hughes, G.; Siner, M.; Tijdhof, B.

2003-01-01

The title study regarding the functioning of the oil market during an oil crisis is carried out with particular reference to the strategic behaviour of oil companies. Section 2 identifies major oil supply disruptions since 1951 and describes some important changes in the market that have occurred in recent decades; Section 3 reviews the economic literature of the functioning of oil markets during disruptions and models of oil supply disruptions; Section 4 examines the response of oil markets to recent supply disruptions; Section 5 examines the incentives and scope for strategic behaviour; Section 6 considers the implications of our analysis for the design of policy responses to oil supply disruptions; Appendix A describes the background to the four recent oil supply disruptions; Appendix B discusses the relationship between spot and futures prices for a storable commodity; and Appendix C is the bibliography

HOW PROPERTIES OF EDIBLE OILS ARE IMPROVED BY ESSENTIAL OILS

Directory of Open Access Journals (Sweden)

SONIA AMARIEI

2016-10-01

Full Text Available The main aim of the present paper is to find out whether the addition of essential oils determines better oxidation stability and positive change of sensory and hedonic perception of edible oils. The oxidation stability of sunflower, corn and grape seed oils was analyzed in the presence of antioxidants in essential oils of rosemary (Rosmarinus officinalis, thyme (Thymus vulgaris and basil (Ocimum basilicum during storage, under conditions of accelerated oxidative processes (4 days, at 60 °C. The total phenolic compounds of these essential oils were determined by the Folin-Ciocalteu method. The DPPH method was used to evaluate the antioxidant capacity of basil, rosemary and thyme essential oils in comparison with known synthetic antioxidant L(+-ascorbic acid. The addition of essential oils to edible oils, the amounts proposed in analyses, determines a favorable influence on their oxidation stability as well as their taste. The influence of addition of essential oils on the taste of edible oils was studied in two products consumed mainly at breakfast, bread and spinach leaves. The results recommend the use of these plant extracts as additives in edible oils rather than synthetic antioxidants.

Mexican oil industry: Shifting to difficult oil

Energy Technology Data Exchange (ETDEWEB)

Bazan G., Gerardo; Gonzalez, Cristobal J.

2010-09-15

Mexico has stepped into an important transition of declining oil fields and new challenging oil projects. The aim of this paper is to show a new perspective of the oil resources that have been exploited throughout the Mexican territory, as well as the remaining resources yet to be exploited. We have developed a resources/production-costs chart that illustrates the historical and future development of the Mexican oil industry, showing the shift that the industry will face in the coming years; this chart was taken from a model already in use by the most prestige energy agencies in the world.

Oil markets to 2010: the impact of non-Opec oil

International Nuclear Information System (INIS)

Enav, Peter

1998-09-01

This report provides an in-depth assessment of oil development scenarios in every non-Opec oil producing country from 1998 to 2010, in addition to evaluating the extent and direction of future oil trade for Opec and non-Opec countries alike. It re-assesses world oil consumption patterns in light of the Asian financial crisis, providing a concise yet comprehensive coverage of an often-neglected oil production group. The oil market development scenario is analysed in each country, with detailed consideration of the major players providing historical production, consumption, import and export data; current oil balance - production, imports and exports; an assessment of oil development policy; analysis of potential development obstacles considering regulatory, financial, political and environmental issues; oil production and consumption projections to 2010, by type; and import and export projections to 2010, by destination and source. More than 80 tables supplying essential statistics on the world's non-Opec markets accompany the report, with maps and schematic diagrams showing existing and potential infrastructure and fields. (Author)

Coconut oil has less satiating properties than medium chain triglyceride oil.

Science.gov (United States)

Kinsella, R; Maher, T; Clegg, M E

2017-10-01

It is well established that the consumption of medium-chain triglycerides (MCT) can increase satiety and reduce food intake. Many media articles promote the use of coconut oil for weight loss advocating similar health benefits to that of MCT. The aim of this study was to examine the effect of MCT oil compared to coconut oil and control oil on food intake and satiety. Following an overnight fast, participants consumed a test breakfast smoothie containing 205kcal of either (i) MCT oil (ii) coconut oil or (iii) vegetable oil (control) on three separate test days. Participants recorded appetite ratings on visual analogue scales and were presented with an ad libitum lunch meal of preselected sandwiches 180min after consumption of the breakfast. The results showed a significant difference in energy and macronutrient intakes at the ad libitum meal between the three oils with the MCT oil reducing food intake compared to the coconut and control oil. Differences in food intake throughout the day were found for energy and fat, with the control having increased food intake compared to the MCT and coconut. The MCT also increased fullness over the three hours after breakfast compared to the control and coconut oils. The coconut oil was also reported as being less palatable than the MCT oil. The results of this study confirm the differences that exist between MCT and coconut oil such that coconut oil cannot be promoted as having similar effects to MCT oil on food intake and satiety. Crown Copyright © 2017. Published by Elsevier Inc. All rights reserved.

Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

Science.gov (United States)

Li, Dongbing; Briens, Cedric; Berruti, Franco

2015-01-01

Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material. Copyright © 2015 Elsevier Ltd. All rights reserved.

Separation of oil and grease from oil sludge using surfactant

International Nuclear Information System (INIS)

Ainon Abdul Aziz; Syed Hakimi Sakuma Syed Ahmad; Zalina Laili

2005-01-01

The objective of the experiments was to observe the efficiency of the surfactant to remove oil and grease from oil sludges using various surfactant concentration ranging from 10 %, 15 %, 20 % and 30 %. The surfactant solution consists of two mixtures of Aqua 2000 and D Bond. The oil sludge were subjected to heating and surfactant treatment process. Remaining oil and grease concentration were observed on the oil sludges after treatment. Small scale experiments were conducted by heating process, without heating process and heating process with addition of sodium chloride. Surfactant solution was added in each process. Results shows that there is separation of oil and grease from the oil sludges. There were formation of mini emulsions (oil in water). The higher the concentration of surfactant used, the higher the concentrations of mini emulsion formed as observed. Solid remains after the treatment process were found to contain lesser oil concentration with presence of bitumen, sediment, organic and inorganic materials. After a washing process using distilled water, the solid was still black but less oily than before the treatment. There is no separation of oil occurred in aqueous solution for the control experiment. (Author)

Oil Spills

Science.gov (United States)

Oil spills often happen because of accidents, when people make mistakes or equipment breaks down. Other causes include natural disasters or deliberate acts. Oil spills have major environmental and economic effects. Oil ...

Process for complete conversion of coal oils, shale oils, etc

Energy Technology Data Exchange (ETDEWEB)

Dubois, P

1911-07-08

A process is described for complete conversion of mineral coal oil, shale oil, and other similar oils in pitch, characterized by these oils being mixed with a nonvolatile substance with a boiling point on the average higher than the boiling point of the oil to be treated, and then being heated under pressure with the introduction of air, whereby the heating is interrupted if necessary on account of the known exothermic reaction and the conversion of the oil in the pitch or its distillation can be carried out without further heating.

Increasing oil recovery from heavy oil waterfloods

Energy Technology Data Exchange (ETDEWEB)

Brice, B.W. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[BP Exploration, Calgary, AB (Canada)

2008-10-15

In an effort to optimize waterflood strategies in Alaska, the authors examined the results of up to 50 years of waterflooding on 166 western Canadian waterfloods recovering oil of less than 30 degrees API. The study determined the best operating practices for heavy oil waterflooding by investigating the difference between waterflooding of heavy oil and lighter oil counterparts. Operators of light oil waterflooding are advised to begin waterflooding early and maintain the voidage replacement ratio (VRR) at 1. However, this study showed that it is beneficial to delay the start of waterflooding until a certain fraction of the original oil in place was recovered. Varying the VRR was also shown to correlate with increased ultimate recovery. This statistical study of 166 western Canadian waterfloods also examined the effect of injection strategy and the effect of primary production before waterflooding. Some pre-waterflood production and under injection time is advantageous for ultimate recovery by waterfloods. Specific recommendations were presented for waterfloods in reservoirs with both high and low API gravity ranges. Each range showed a narrow sweet spot window where improved recovery occurred. 27 refs., 13 figs.

Comparative Effect of Dietary Soybean Oil, Fish Oil, and Coconut Oil on Performance, Egg Quality and Some Blood Parameters in Laying Hens.

Science.gov (United States)

Dong, X F; Liu, S; Tong, J M

2018-04-14

Two hundred and sixteen 28-wk-old Hy-line laying hens were randomly distributed to three dietary treatments and fed 1of 3 diets containing 8% soybean oil, fish oil, or coconut oil from 28 to 47 wk of age to investigate comparative effect of dietary soybean oil, fish oil, and coconut oil on the performance, egg quality and blood malondialdehyde (MDA), aspartate transaminase (AST) and uric acid (UA). Hens fed fish oil showed poor performance compared with soybean oil or coconut oil, and especially egg weight throughout the trial was significantly and consistently decreased (P oil. Unexpectedly, shell reflectivity throughout the majority of the trial was consistently and significantly higher (P oil than that when fed soybean oil or coconut oil. Dietary treatments affected (P oil treatment was higher (P oil group. Albumen height, Haugh unit and yolk color were influenced by dietary treatments only at 1 or 2 time points. However, average albumen height and Haugh unit in fish oil treatment were higher (P soybean oil or coconut oil treatments and average yolk color in coconut oil treatment was higher (P soybean oil group. Serum MDA, AST and UA concentrations were increased (P oil during the majority of the first 2 mo of the trial. These data suggested that the inclusion of fish oil into feed may reduce the performance of laying hens, especially the egg weight, decrease the intensity of egg brown color and increase blood MDA, AST and UA levels compared with soybean oil or coconut oil. As a result, hens fed fish oil may lay smaller, longer and lighter-brown eggs whereas those fed coconut oil produce blunter and darker-brown eggs relative to soybean oil.

Production of oil from Israeli oil shale

International Nuclear Information System (INIS)

Givoni, D.

1993-01-01

Oil shale can be utilized in two-ways: direct combustion to generate steam and power or retorting to produce oil or gas. PAMA has been developing both direct combustion and retorting processes. Its main effort is in the combustion. An oil shale fired steam boiler was erected in the Rotem industrial complex for demonstration purposes. PAMA has also been looking into two alternative retorting concepts - slow heating of coarse particles and fast heating of fine particles. The present paper provides operating data of oil shale processing in the following scheme: (a) retorting in moving bed, pilot and bench scale units, and (b) retorting in a fluidized bed, bench scale units. (author)

Pyrolysis Strategies for Effective Utilization of Lignocellulosic and Algal Biomass

Science.gov (United States)

Maddi, Balakrishna

protein degradation). Algal bio-char also had a significantly higher N-content. Overall, our results suggest that it is feasible to convert algal cultures deficient in lipids, such as nuisance algae obtained from natural blooms, into liquid fuels by thermochemical methods. Next, pyrolysis characteristics of each of the major components present in lignocellulosic as well as algal biomass were studied independently in a thermo-gravimetric analyzer, using model compounds. From those studies, we have established that, with algae and oil seed feed stocks, triglycerides degrade at distinctly higher temperatures (T>350 C) compared to both protein and carbohydrate fractions (T ~ 250-350 C). Similar trend was not seen for lignocellulosic biomass, where degradation temperature interval of lignin overlapped with that of carbohydrates. This unique trend observed for algal biomass (and oil seeds) can be exploited in multiple ways. First, it permits to separately collect high value triglyceride degradation products not contaminated with N-compounds from protein and oxygenates from carbohydrates; this observation formed the basis of a novel "pyrolytic fractionation technique" developed in this thesis. Second, it led to the development of a new and simple analytical method for rapid estimation of the triglyceride content of oleaginous feed stocks. Pyrolytic fractionation is a two-step pyrolysis approach that can be implemented for oleaginous feed stocks (algae and oil-seeds) to separately recover triglyceride degradation products as a "high-quality" bio-oil fraction. The first step is a low-temperature pyrolysis (T ~ 300-320 C) to produce bio-oils from degradation of protein and carbohydrate fractions. Solid residues left behind can subsequently be subjected to a second higher temperature pyrolysis (T ~ 420-430 C) to volatilize and/or degrade triglycerides to produce fatty acids and their derivatives (such as mono-, di- and tri-glycerides) and long chain hydrocarbons. Proof

Genetic determinism of oil acidity among some DELI oil palm (Elaeis ...

African Journals Online (AJOL)

USER

2016-08-24

Aug 24, 2016 ... Key words: Elaeis guineensis Jacq., free fatty acid content, crude palm oil, inheritance. INTRODUCTION. The oil palm (Elaeis ... of world's production of vegetable oils. The highest palm oil producing countries ... Without prior refining, acidic palm oil is improper for human consumption (Anonymous, 2005).

Improving oil classification quality from oil spill fingerprint beyond six sigma approach.

Science.gov (United States)

Juahir, Hafizan; Ismail, Azimah; Mohamed, Saiful Bahri; Toriman, Mohd Ekhwan; Kassim, Azlina Md; Zain, Sharifuddin Md; Ahmad, Wan Kamaruzaman Wan; Wah, Wong Kok; Zali, Munirah Abdul; Retnam, Ananthy; Taib, Mohd Zaki Mohd; Mokhtar, Mazlin

2017-07-15

This study involves the use of quality engineering in oil spill classification based on oil spill fingerprinting from GC-FID and GC-MS employing the six-sigma approach. The oil spills are recovered from various water areas of Peninsular Malaysia and Sabah (East Malaysia). The study approach used six sigma methodologies that effectively serve as the problem solving in oil classification extracted from the complex mixtures of oil spilled dataset. The analysis of six sigma link with the quality engineering improved the organizational performance to achieve its objectivity of the environmental forensics. The study reveals that oil spills are discriminated into four groups' viz. diesel, hydrocarbon fuel oil (HFO), mixture oil lubricant and fuel oil (MOLFO) and waste oil (WO) according to the similarity of the intrinsic chemical properties. Through the validation, it confirmed that four discriminant component, diesel, hydrocarbon fuel oil (HFO), mixture oil lubricant and fuel oil (MOLFO) and waste oil (WO) dominate the oil types with a total variance of 99.51% with ANOVA giving F stat >F critical at 95% confidence level and a Chi Square goodness test of 74.87. Results obtained from this study reveals that by employing six-sigma approach in a data-driven problem such as in the case of oil spill classification, good decision making can be expedited. Copyright © 2017. Published by Elsevier Ltd.

Comparative effects of dietary corn oil, safflower oil, fish oil and palm oil on metabolism of ethanol and carnitine in the rat.

Science.gov (United States)

Sachan, Dileep S; Yatim, Ayub M; Daily, James W

2002-06-01

This study was launched to determine comparative effects of corn oil (CO), safflower oil (SO), fish oil (FO) and palm oil (PO) on carnitine status and ethanol metabolism in rats. Twenty-four male Sprague-Dawley rats (300 g bw) were randomly divided into four groups (n = 6) and fed a semisynthetic diets containing fat as oils listed above. Blood and 24 hour urine samples were collected before and after dietary treatment and acute ethanol administration. Samples were analyzed for blood-ethanol concentration (BEC) and carnitine species. The diets containing FO and PO retarded ethanol metabolism compared to the diets containing CO and SO. The effect of these dietary fats on carnitine species in plasma and urine was varied before and after dietary treatment and following a single oral ethanol dose. The liver carnitine content was higher in the PO group after dietary and ethanol treatment. It is concluded that attenuation of ethanol clearance was related to unique fatty acid makeup of the oils that in part may be attributed to the composite ratio of saturated to unsaturated fatty acids in the oils.

Wash-oil problem

Energy Technology Data Exchange (ETDEWEB)

Chlosta, J

1941-01-01

Meier-Grolman and others have deduced from experimental studies of the vapor pressure of solutions of benzene in paraffin oil and Solway oil-paraffin oil mixtures that the higher the proportion of aliphatic compounds in a wash oil, the less suitable it is for benzene scrubbing. This generalization is not supported. Paraffin oils from brown-coal tar and low viscous oils from the Fischer-Tropsch hydrocarbon synthesis process are both being successfully used for benzene scrubbing.

Effect of substrate temperature on the properties of pyrolytically deposited nitrogen-doped zinc oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Golshahi, S., E-mail: golshahi@iaurasht.ac.ir [Department of Physics, Rasht Branch, Islamic Azad University, Rasht (Iran, Islamic Republic of); Rozati, S.M. [Department of Physics, University of Guilan, 41335-1914 Rasht (Iran, Islamic Republic of); Botelho do Rego, A.M. [Centro de Quimica-Fisica Molecular and IN, Technical University of Lisbon, IST 1049-001 Lisboa (Portugal); Wang, J. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Elangovan, E.; Martins, R.; Fortunato, E. [CENIMAT/I3N, Departamento de Ciencia dos Materiais, Faculdade de Ciencias e Tecnologia, FCT, Universidade Nova de Lisboa (UNL), 2829-516 Caparica (Portugal)

2013-01-01

Highlights: Black-Right-Pointing-Pointer Hall-effect measurement introduces the optimum temperature of 450 Degree-Sign C for fabricating p-type high quality ZnO films. Black-Right-Pointing-Pointer X-ray photoelectron spectroscopy (XPS) proved the nitrogen presence at the surface of doped ZnO thin films at all substrate temperatures. Black-Right-Pointing-Pointer Films prepared at lower substrate temperature (300 Degree-Sign C and 350 Degree-Sign C) own wider band gaps. Black-Right-Pointing-Pointer Surface roughness strongly is affected by substrate temperature variations. - Abstract: The effect of substrate temperature (T{sub s}) on the properties of pyrolytically deposited nitrogen (N) doped zinc oxide (ZnO) thin films was investigated. The T{sub s} was varied from 300 Degree-Sign C to 500 Degree-Sign C, with a step of 50 Degree-Sign C. The positive sign of Hall coefficient confirmed the p-type conductivity in the films deposited at 450 Degree-Sign C and 500 Degree-Sign C. X-ray diffraction studies confirmed the ZnO structure with a dominant peak from (1 0 0) crystal plane, irrespective of the variation in T{sub s}. The presence of N in the ZnO structure was evidenced through X-ray photoelectron spectroscopy (XPS) analysis. The obtained high N concentration reveals that the 450 Degree-Sign C is the optimal T{sub s}. Atomic force microscope (AFM) analysis showed that the surface roughness was increased with the increasing T{sub s} until 400 Degree-Sign C but then decreased. It is found that the transmittance of the deposited films is increased with the increasing T{sub s}. The optical band gap calculated from the absorption edge showed that the films deposited with T{sub s} of 300 Degree-Sign C and 350 Degree-Sign C possess higher values than those deposited at higher T{sub s}.

Effect of substrate temperature on the properties of pyrolytically deposited nitrogen-doped zinc oxide thin films

International Nuclear Information System (INIS)

Golshahi, S.; Rozati, S.M.; Botelho do Rego, A.M.; Wang, J.; Elangovan, E.; Martins, R.; Fortunato, E.

2013-01-01

Highlights: ► Hall-effect measurement introduces the optimum temperature of 450 °C for fabricating p-type high quality ZnO films. ► X-ray photoelectron spectroscopy (XPS) proved the nitrogen presence at the surface of doped ZnO thin films at all substrate temperatures. ► Films prepared at lower substrate temperature (300 °C and 350 °C) own wider band gaps. ► Surface roughness strongly is affected by substrate temperature variations. - Abstract: The effect of substrate temperature (T s ) on the properties of pyrolytically deposited nitrogen (N) doped zinc oxide (ZnO) thin films was investigated. The T s was varied from 300 °C to 500 °C, with a step of 50 °C. The positive sign of Hall coefficient confirmed the p-type conductivity in the films deposited at 450 °C and 500 °C. X-ray diffraction studies confirmed the ZnO structure with a dominant peak from (1 0 0) crystal plane, irrespective of the variation in T s . The presence of N in the ZnO structure was evidenced through X-ray photoelectron spectroscopy (XPS) analysis. The obtained high N concentration reveals that the 450 °C is the optimal T s . Atomic force microscope (AFM) analysis showed that the surface roughness was increased with the increasing T s until 400 °C but then decreased. It is found that the transmittance of the deposited films is increased with the increasing T s . The optical band gap calculated from the absorption edge showed that the films deposited with T s of 300 °C and 350 °C possess higher values than those deposited at higher T s .

Oil-in-oil emulsions stabilised solely by solid particles.

Science.gov (United States)

Binks, Bernard P; Tyowua, Andrew T

2016-01-21

A brief review of the stabilisation of emulsions of two immiscible oils is given. We then describe the use of fumed silica particles coated with either hydrocarbon or fluorocarbon groups in acting as sole stabilisers of emulsions of various vegetable oils with linear silicone oils (PDMS) of different viscosity. Transitional phase inversion of emulsions, containing equal volumes of the two oils, from silicone-in-vegetable (S/V) to vegetable-in-silicone (V/S) occurs upon increasing the hydrophobicity of the particles. Close to inversion, emulsions are stable to coalescence and gravity-induced separation for at least one year. Increasing the viscosity of the silicone oil enables stable S/V emulsions to be prepared even with relatively hydrophilic particles. Predictions of emulsion type from calculated contact angles of a silica particle at the oil-oil interface are in agreement with experiment provided a small polar contribution to the surface energy of the oils is included. We also show that stable multiple emulsions of V/S/V can be prepared in a two-step procedure using two particle types of different hydrophobicity. At fixed particle concentration, catastrophic phase inversion of emulsions from V/S to S/V can be effected by increasing the volume fraction of vegetable oil. Finally, in the case of sunflower oil + 20 cS PDMS, the study is extended to particles other than silica which differ in chemical type, particle size and particle shape. Consistent with the above findings, we find that only sufficiently hydrophobic particles (clay, zinc oxide, silicone, calcium carbonate) can act as efficient V/S emulsion stabilisers.

Comparative study of ozonized olive oil and ozonized sunflower oil

Directory of Open Access Journals (Sweden)

Díaz Maritza F.

2006-01-01

Full Text Available In this study the ozonized olive and sunflower oils are chemical and microbiologically compared. These oils were introduced into a reactor with bubbling ozone gas in a water bath at room temperature until they were solidified. The peroxide, acidity and iodine values along with antimicrobial activity were determined. Ozonization effects on the fatty acid composition of these oils were analyzed using Gas-Liquid Chromatographic Technique. An increase in peroxidation and acidity values was observed in both oils but they were higher in ozonized sunflower oil. Iodine value was zero in ozonized olive oil whereas in ozonized sunflower was 8.8 g Iodine per 100 g. The antimicrobial activity was similar for both ozonized oils except for Minimum Bactericidal Concentrations of Pseudomona aeruginosa. Composition of fatty acids in both ozonized oils showed gradual decrease in unsaturated fatty acids (C18:1, C18:2 with gradual increase in ozone doses.

Oil crises

International Nuclear Information System (INIS)

Linderoth, H.

1992-01-01

The author's aim was to give very precise information on the many causes and effects of the oil crises that have occurred since 1900, and at the same time offer the reader the possibility to build up a basic knowledge of the oil industry and market, as he feels that the public is often subjected to misleading information. Political and economical aspects are elaborated. First-hand sources such as statistics and investigations have been used as far as possible to give information on the oil market. An oil crisis is defined by the author as a significant change in the price of oil compared to prices of other goods. Changes can be in the form of either rising or falling prices. A special chapter concentrates on Denmark in relation to the oil crises. (AB) (165 refs.)

[Efficiency evaluation of capsaicinoids to discriminate bio-waste oils from edible vegetable oils].

Science.gov (United States)

Mao, Lisha; Liu, Honghe; Kang, Li; Jiang, Jie; Liao, Shicheng; Liu, Guihua; Deng, Pingjian

2014-07-01

To evaluate the efficiency of capsaicinoids to discriminate bio-waste oil from edible vegetable oil. 14 raw vegetable oils, 24 fried waste oils, 34 kitchen-waste oils, 32 edible non-peanut vegetable oil, 32 edible peanuts oil, 16 edible oil add flavorand and 11 refined bio-waste oils were prepared and examined for capsaicinoids including capsaicin, dihydrocapsaicin and nonylic acid vanillylamide. The detection results of the above samples were statistically tested based on sample category to assessment identify the effectiveness of the bio-waste oils with capsaicinoids. As a indicator, capsaincin was possessed of high detection sensitivity and has the highest efficiency to discern kitchen-waste oils and refined bio-waste oils samples from edible non-peanut vegetable oil correctly. The accuracy rate of identification were 100% and 90.1% respectively. There is the background in peanut oil. CONCLUSION Capsaicin added in cooking process can be retained in the refining process and hardly be removed in the refining process. In the case of fully eliminating the background interference, capsaicinoids can effectively identify bio-waste oils and edible vegetable oil in combination.

Oil trading manual

International Nuclear Information System (INIS)

Long, D.

1995-01-01

This manual provides basic information on all aspects of oil trading. Topics reviewed in Part 1 include physical characteristics and refining and oil pricing arrangements. Part 2 on instruments and markets contains chapters on crude oil markets, product markets, forward and futures contracts, forward paper markets, oil future exchanges, options, swaps and long term oil markets. Part 3 deals with administration and has chapters on operations and logistics, credit control, accounting, taxation of oil trading, contracts and legal and regulatory issues. (UK)

Myristica oil poisoning

Science.gov (United States)

Nutmeg oil; Myristicin ... Myristica oil ( Myristica fragrans ) can be harmful. It comes from the seed of a nutmeg. ... Myristica oil is found in: Aromatherapy products Mace Nutmeg Other products may also contain myristica oil.

Mining and oil. Oil shale's contribution to future oil supply; Bergbau und Oel. Der Beitrag des Oelschiefers zur Oelversorgung

Energy Technology Data Exchange (ETDEWEB)

Linden, Eike von der [Linden Advisory, Dreieich (Germany)

2012-05-15

Crude oil contributes in Germany and globally approximately one third to the consumption of primary energies and actually is and in the foreseeable future will be the most important energy source. Recently shale oil as an unconventional oil has gained attention in public discussions. Depending on temperatures oil shale contains either already matured fluid shale oil or immature waxy kerogen. For determination of kerogen containing oil shale and shale oil common definitions for fluid hydrocarbons will be presented. Fluid hydrocarbons (molecular chains > C{sub 5}H{sub 12}) originate from animal substance which had been settled millions of years in sediments on sea- or lakebeds under anaerobic conditions. High pressure and high temperatures effect conversion to hydrocarbons. With sufficient permeability the liquid hydrocarbons migrate from the sediment as the source rock and get assembled in porous rocks under the cover of an impermeable rock strata, in so called entrapment structures. In case there is no impermeable rock strate the hydrocarbons will diffuse into the atmosphere. The hydrocarbons in entrapment structures are called conventional oil and are extracted by drilling wells. The extractable oil as part of the oil in place depends on the viscosity of the oil, the permeability of the host rock and applied exploitation methods which can affect pressure, viscosity and permeability. The exploitation achieves 30 to 50% of the oil in place. When the source rock consisting of strata hundreds of meters thick is not sufficiently permeable the matured hydrocarbons remain at its place of origination. These hydrocarbons are called shale oil and belong to the unconventional oil resources. For exploitation of shale oil by wells the source rock must be treated by intensive energy input, amongst others, by fracking which creates artificial permeability and by pressure which affects migration of the hydrocarbons to the well. The exploitation methods for shale oil do not

Comparison of lubricant properties of castor oil and commercial engine oil

Directory of Open Access Journals (Sweden)

Binfa Bongfa

2015-06-01

Full Text Available The tribological performance of crude Nigeria-based castor oil has been investigated and compared with that of a foreign, 20W-50 high quality crankcase oil, to see its suitability as base oil for lubricating oils in indigenous vehicle and power plants engines. The experiment was conducted using a four ball tester. The results showed that unrefined castor oil has superior friction reduction and load bearing capability in an unformulated form than the commercial oil; can compete favourably with the commercial oil in wear protection when formulated with suitable antiwear agent, hence can be a good alternative base stock for crankcase oils suitable for Nigeria serviced vehicles, and plants engines from tribological, environmental, and non-food competitive points of view.

RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Anthony R. Kovscek; William E. Brigham

1999-06-01

The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

Experimental study on kinetics oil oil-suspended particulate matter aggregation

International Nuclear Information System (INIS)

Sun, J.; Environment Canada, Ottawa, ON; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C.; Zheng, X.; Wong, S.; So, L.C.

2009-01-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs

Experimental study on kinetics oil oil-suspended particulate matter aggregation

Energy Technology Data Exchange (ETDEWEB)

Sun, J. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Khelifa, A.; Wang, Z.; Brown, C.; Fieldhouse, B.; Yang, C. [Environment Canada, Ottawa, ON (Canada). Emergencies Science and Technology Section, Emergencies, Operational Analytical Laboratories and Research Support Division; Zheng, X. [Ocean Univ. of China, Qingdoa (China). Environmental Science and Engineering Inst.; Wong, S. [Ottawa Univ., ON (Canada). Dept. of Chemistry; So, L.C. [Waterloo Univ., ON (Canada). Faculty of Engineering

2009-07-01

Past studies of oil spills have shown that oil suspended particulate matter aggregates (OSAs) play a role in enhancing the natural cleansing of oiled shorelines. OSAs result from aggregation between suspended oil droplets and suspended particulate matter (SPM) in aquatic environments. During this process, oil dispersion into the water column is significantly increased since the surface of the oil droplet is surrounded by sediment particles. In addition, the accelerated biodegradation of the oil can be attributed to the greater oil-water contact area. This study focused on the kinetic aspects of OSA formation, with particular reference to the time scale of this process and its significance to oil dispersion following oil spills in water. A laboratory study was conducted to measure the time scale of OSA formation and its variations with mixing conditions. A reciprocating shaker and various oil/sediment mixtures were used to prepare the OSAs. Standard reference material 1941b was used as the natural sediment mixed with Arabian medium crude and artificial seawater under various mixing energies. The sediment-to-oil ratio remained constant for all experiments. Gas chromatography-flame ionization detection (GC-FID) analysis was used to measure the total petroleum hydrocarbons (TPH) trapped in negatively buoyant OSAs. Results showed that the TPH in OSAs increased exponentially with shaking time and reached an equilibrium value within 3 hours. The equilibrium decreased from 3 hours to 1.3 hours when the shaking rate increased from 2.0 to 2.3 Hz. It was concluded that high mixing energy enhances OSA formation and shortens the time for OSA formation. 42 refs., 6 tabs., 5 figs.

Oil intensities and oil prices : evidence for Latin America

OpenAIRE

Alaimo, Veronica; Lopez, Humberto

2008-01-01

Crude oil prices have dramatically increased over the past years and are now at a historical maximum in nominal terms and very close to it in real terms. It is difficult to argue, at least for net oil importers, that higher oil prices have a positive impact on welfare. In fact, the negative relationship between oil prices and economic activity has been well documented in the literature. Ye...

A catalogue of crude oil and oil product properties, 1990

International Nuclear Information System (INIS)

Bobra, M.A.; Callaghan, S.

1990-09-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

A catalogue of crude oil and oil product properties, 1992

International Nuclear Information System (INIS)

Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

1993-02-01

This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

Contribution to the study of hard, low-density pyrolytic carbons; Contribution a l'etude des carbones pyrolytiques de variete dure et de faible densite

Energy Technology Data Exchange (ETDEWEB)

Boutin, F R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-07-01

Apparent contradictions in the properties of pyrolytic carbons obtained at 1600 deg C (hardness and graphitization) are studied. It is shown that structure of the deposit is turbostratic with high internal stresses ({delta}{sup -2}), and it graphitizes (by thermal treatment over 2000 deg C) in a similar manner to graphitisable carbon. Because the deposit forms lamellar compounds, it is presumed that the structure is similar to that of graphitisable carbon. Since it is not structure dependant, the hardness originates from the 'growth texture' and is not comparable with the hardness of a non-graphitisable carbon. The pyrolytic carbon studied is composed of regions, on the overage a few microns across, formed by the stacking of small carbon platelets, interlocked and showing a preferred orientation. The mis-orientation of the various regions produces general disorientation. We estimate that the introduction of the particles of some material such as thermal black which are observed in the electron microscope are responsible for the mis-orientation. The density and hardness of the deposit are a result of the interlocking of platelets, which creates a closed porosity and prevents any sliding of the atomic planes. (author) [French] On etudie les proprietes apparemment contradictoires du pyrocarbone 1600 deg C, durete et graphitabilite. On montre que le pyrocarbone possede la structure d'un carbone turbostratique a fort taux de distorsion et qu'il subit, par traitement a des temperatures superieures a 2000 deg C, une transformation de graphitation comparable a celle que l'on observe sur les cokes graphitables. Comme le pyrocarbone forme de plus des composes d'insertion, sa structure est comparable a celle d'un carbone graphitable. La durete, qui n'a pas d'origine structurale, est donc liee a la 'texture de croissance' du depot et ne peut etre comparee a celle d'un coke dur et non graphitable. Le pyrocarbone etudie est constitue de domaines, dont les dimensions sont de l

Neutron Backscattered Technique for Quantification of Oil Palm Fruit Oil Content

International Nuclear Information System (INIS)

Ismail Mustapha; Samihah Mustaffha; Md Fakarudin Ab Rahman; Roslan Yahya; Lahasen Norman Shah Dahing; Nor Paiza Mohd Hasan; Jaafar Abdullah

2013-01-01

Non-destructive and real time method becomes a well-liked method to researchers in the oil palm industry since 2000. This method has the ability to detect oil content in order to increase the production of oil palm for better profit. Hence, this research investigates the potential of neutron source to estimate oil content in palm oil fruit since oil palm contains hydrogen with chemical formula C 55 H 96 O 6 . For this paper, oil palm loose fruit was being used and divided into three groups. These three groups are ripe, under-ripe and bruised fruit. A total of 21 loose fruit for each group were collected from a private plantation in Malaysia. Each sample was scanned using neutron backscattered technique. The higher neutron count, the more hydrogen content, and the more oil content in palm oil fruit. The best correlation result came from the ripe fruits with r 2 =0.98. This research proves that neutron backscattered technique can be used as a non-destructive and real time grading system for palm oil. (author)

Mitsubishi Oil to become a major oil player?

International Nuclear Information System (INIS)

Ash, N.

1994-01-01

Mitsubishi Oil became a wholly-owned Japanese company in 1984. Before that, since 1981, it had been a joint venture between Mitsubishi and Getty oil. Recently the company has discovered a major new oilfield off the coast of Vietnam. In addition it has a strategic stake in the Canadian Athabasca Far Sands, major investments in Angola and operations in Papua New Guinea and Gabon. It aims to cover 30 % of the crude oil imports to its four existing, and fifth projected, refineries from owned sources by the end of the century. Mitsubishi has a network of 4500 service stations in Japan and has become one of the largest lubricating oil producers. The company's main overseas sales are of jet fuel, lubricating and tanker oils, sulphur and some petrochemicals. (UK)

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

Science.gov (United States)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

Global Trends and Development Prospects for Oil and the Oil Products Market

Directory of Open Access Journals (Sweden)

Maria Dorozhkina

2006-03-01

Full Text Available This article discusses the important issue of the development of the global market of oil and oil products. It offers an overview of how this market was formed and its current status, classification, location and potential of countries in the oil and oil processing business. It analyzes the Ukrainian oil products market. The article discusses the shortcomings and strategic areas for the development of Ukraine’s oil transport system. It presents an optimum method for creating integration groups in order to develop the oil processing business in Ukraine for the future. The article considers the main trends and outlines development prospects for the global oil and oil products market.

The oil price

International Nuclear Information System (INIS)

Alba, P.

2000-01-01

Statistical analysis cannot, alone, provide an oil price forecast. So, one needs to understand the fundamental phenomena which control the past trends since the end of world war II After a first period during which oil, thanks to its abundance, was able to increase its market share at the expense of other energies, the first oil shock reflects the rarefaction of oil resource with the tilting of the US production curve from growth to decline. Since then, the new situation is that of a ''cohabitation'' between oil and the other energies with the oil price, extremely volatile, reflecting the trial and error adjustment of the market share left to the other energies. Such a context may explain the recent oil price surge but the analogy between the US oil situation at the time of the first shock and that existing today for the world outside Middle East suggest another possibility, that of a structural change with higher future oil prices. The authors examine these two possibilities, think that the oil price will reflect both as long as one or the other will not become proven, and conclude with a series of political recommendations. (authors)

Oil My Love

International Nuclear Information System (INIS)

Gay, Michel

2014-01-01

The author first describes how oil will disappear from non-producing countries, notably France and Europe and will therefore lead to an energy crisis. He outlines that renewable energies will have a weak contribution in the replacement of fossil energies (in this case, oil and gas). To illustrate these trends, the author proposes an appendix which presents and discusses the evolution of global consumption of fossil fuels, the evolution of production of different oil grades, a forecast of global oil demand by 2035, evolutions of productions and exports. Another appendix discusses additional issues on oil: the meaning of reserves, solutions for France in case of shortage of oil, the world oil situation (USA, China, Russia, the European Union, Japan)

Non-Petroleum Oils

Science.gov (United States)

These include synthetics such as silicone fluids and tung oils, wood-derivative oils such as resin/rosin, animal fats/oil, and seed oils. Many have similar physical properties to petroleum-based, such as water insolubility and formation of slicks.

Hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Foorwood, G F; Taplay, J G

1916-12-12

Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

The oil industry in 2007

International Nuclear Information System (INIS)

2008-01-01

The various contributions present and comment many data about the evolutions of different parts of the oil industry until 2007: world oil and gas markets, worldwide oil exploration and production, oil exploration and production in France, oil and oil-related industry in France, hydrocarbon supplies, oil refining in France, fuel quality, substitution fuels, inner transportation of oil products, storage of oil products, consumption of oil products, taxing of oils products, price of oil products, distribution of oil products

The oil industry in 2006

International Nuclear Information System (INIS)

2007-01-01

The various contributions present and comment many data about the evolutions of different parts of the oil industry until 2006: world oil and gas markets, worldwide oil exploration and production, oil exploration and production in France, oil and oil-related industry in France, hydrocarbon supplies, oil refining in France, fuel quality, substitution fuels, inner transportation of oil products, storage of oil products, consumption of oil products, taxing of oils products, price of oil products, distribution of oil products

Detection of olive oil adulteration by low-field NMR relaxometry and UV-Vis spectroscopy upon mixing olive oil with various edible oils

Directory of Open Access Journals (Sweden)

S. Ok

2017-03-01

Full Text Available Adulteration of olive oil using unhealthy substitutes is considered a threat for public health. Low-field (LF proton (1H nuclear magnetic resonance (NMR relaxometry and ultra-violet (UV visible spectroscopy are used to detect adulteration of olive oil. Three different olive oil with different oleoyl acyl contents were mixed with almond, castor, corn, and sesame oils with three volumetric ratios, respectively. In addition, Arbequina olive oil was mixed with canola, flax, grape seed, peanut, soybean, and sunflower seed oils with three volumetric ratios. Transverse magnetization relaxation time (T2 curves were fitted with bi-exponential decaying functions. T2 times of each mixture of olive oils and castor oils, and olive oils and corn oils changed systematically as a function of volumetric ratio. To detect the adulteration in the mixtures with almond and sesame oils, both LF 1H NMR relaxometry and UV-Vis spectroscopy were needed, where UV-Vis-spectroscopy detected the adulteration qualitatively. In the mixtures of Arbequina olive oil and flax, peanut, soybean, and sunflower seed oils, both T21 and T22 values became longer systematically as the content of the olive oil was decreased. The unique UV-Vis maximum absorbance of flax oil at 320.0 nm shows the adulteration of olive oil qualitatively.

Detection of olive oil adulteration by low-field NMR relaxometry and UV-Vis spectroscopy upon mixing olive oil with various edible oils

International Nuclear Information System (INIS)

Ok, S.

2017-01-01

Adulteration of olive oil using unhealthy substitutes is considered a threat for public health. Low-field (LF) proton (1H) nuclear magnetic resonance (NMR) relaxometry and ultra-violet (UV) visible spectroscopy are used to detect adulteration of olive oil. Three different olive oil with different oleoyl acyl contents were mixed with almond, castor, corn, and sesame oils with three volumetric ratios, respectively. In addition, Arbequina olive oil was mixed with canola, flax, grape seed, peanut, soybean, and sunflower seed oils with three volumetric ratios. Transverse magnetization relaxation time (T2) curves were fitted with bi-exponential decaying functions. T2 times of each mixture of olive oils and castor oils, and olive oils and corn oils changed systematically as a function of volumetric ratio. To detect the adulteration in the mixtures with almond and sesame oils, both LF 1H NMR relaxometry and UV-Vis spectroscopy were needed, where UV-Vis-spectroscopy detected the adulteration qualitatively. In the mixtures of Arbequina olive oil and flax, peanut, soybean, and sunflower seed oils, both T21 and T22 values became longer systematically as the content of the olive oil was decreased. The unique UV-Vis maximum absorbance of flax oil at 320.0 nm shows the adulteration of olive oil qualitatively. [es

Kolkhoung (Pistacia khinjuk Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability and Nutritional Value

Directory of Open Access Journals (Sweden)

Maryam Asnaashari

2015-01-01

Full Text Available In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high–performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well-balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation–sensitive oils to improve their shelf life.

Experimental oil release on Haltenbanken 1982. Drifting and spreading of oil. [Norway

Energy Technology Data Exchange (ETDEWEB)

Soerstroem, S.E.; Johansen, Oe; Celius, K.K.; Audunson, T.; Steinbakke, P.

1984-03-29

In the experiment, 100 m/sup 3/ of Statfjord crude oil was released at Haltenbanken. The oil was followed for 7 days and projects concerning drifting and spreading of oil, microbiological decay and ecological effects, ecological studies of the impact on fish, zooplancton, fish eggs and larvae, training with equipment and control functions and experiment leading and coordination were carried out. In this project ''drifting and spreading of oil'' information on physical environment, decay of oil, mixing of oil in water, oil spill surveillance, warning and simulation and numerical modelling are collected. The results of these areas were compared to the mathematical simulation and warning models Oilsim and Sliktrak. New methods for in situ measurements for relative values of oil in water were used. It was found that most of the physical and chemical changes of oil spills occur during the first 24 hours. The drifting and alterations of the oil was recorded and a new simulation model for three-dimentional spreading of oil in water was made. 49 tables, 130 drawings, 32 references.

Oil biodegradation

NARCIS (Netherlands)

Rahsepar, Shokouhalsadat; Langenhoff, Alette A.M.; Smit, Martijn P.J.; Eenennaam, van Justine S.; Murk, Tinka; Rijnaarts, Huub H.M.

2017-01-01

During the Deepwater Horizon (DwH) oil spill, interactions between oil, clay particles and marine snow lead to the formation of aggregates. Interactions between these components play an important, but yet not well understood, role in biodegradation of oil in the ocean water. The aim of this study

Estimation on oil demand and oil saving potential of China's road transport sector

International Nuclear Information System (INIS)

Lin, Boqiang; Xie, Chunping

2013-01-01

China is currently in the stage of industrialization and urbanization, which is characterized by rigid energy demand and rapid growth of energy consumption. Therefore, energy conservation will become a major strategy for China in a transition to low-carbon economy. China's transport industry is of high energy consumption. In 2010, oil consumption in transport industry takes up 38.2% of the country's total oil demand, of which 23.6% is taken up by road transport sector. As a result, oil saving in China's road transport sector is vital to the whole nation. The co-integration method is developed to find a long-run relationship between oil consumption and affecting factors such as GDP, road condition, labor productivity and oil price, to estimate oil demand and to predict future oil saving potential in China's transport sector under different oil-saving scenarios. Monte Carlo simulation is further used for risk analysis. Results show that under BAU condition, oil demand of China's road transport sector will reach 278.5 million ton of oil equivalents (MTOE) in 2020. Oil saving potential will be 86 MTOE and 131 MTOE under moderate oil-saving scenario and advanced oil-saving scenario, respectively. This paper provides a reference to establishing oil saving policy for China's road transport sector. - Highlights: • We adopt the co-integration model to estimate oil demand and oil saving potential of China's road transport sector. • Monte Carlo simulation is further used for risk analysis. • GDP, ratio of classified highway, labor productivity and oil price are main factors affecting oil consumption. • Scenario analysis approach is applied to calculate oil saving potential under different energy saving scenarios. • Future policy for oil conservation in China's road transport sector is suggested

Cracking hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Seigle, A A.F.M.

1922-12-20

Hydrocarbon oils such as petroleum, peat, shale, or lignite oils, heavy tars, resin oils, naphthalene oils, etc., are vaporized by being fed from a tank through a preheater to the lower part of a vertical annular retort heated by a flame projected down the central cavity from a burner. The oil vapors rise through annular passages formed by disks, on which are placed chips of copper, iron, aluminum, etc., to act as catalysts.

Efficient way of importing crude oil from oil producing countries - A review on diversification policy of crude oil import

Energy Technology Data Exchange (ETDEWEB)

Lee, Dal Sok [Korea Energy Economics Institute, Euiwang (Korea)

1999-03-01

Since the second oil crisis, the government has operated the import diversification support program to reduce the risk of crude oil import from Middle-East region and to raise the ability of dealing with the risk. This study tried to seek policy trends in future through reviewing the market environment related to the crude oil import diversification policy and the goal, instrument and effect of the policy. The supply and demand of crude oil and the price are influenced by market system in the world oil market and there are various types of crude oil trading available to both sellers and buyers. There is a probability that the suspension of supply in a certain area could be led to the price issue rather than the physical use of crude oil. In addition, the advantage of price with long-term contract of crude oil was abolished since the price of crude oil imported by term contract has been linked to spot prices. As a result, it is shown that the potential benefit from crude oil import diversification policy is reduced although political and social insecurity still exists in Middle-East region. Therefore, it is desirable to maintain the existing support program until the amount of stored oil reaches the optimum level and to help private enterprises determine the import considering economical efficiency and risk. (author). 36 refs., 5 figs., 23 tabs.

Transformer oil maintenance

Energy Technology Data Exchange (ETDEWEB)

White, J. [A.F. White Ltd., Brantford, ON (Canada)

2002-08-01

Proactive treatment is required in the case of transformer oil, since the oil degrades over time, which could result in the potential failure of the transformer or costly repairs. A mineral-based oil is used for transformers because of its chemical properties and dielectric strength. Water and particulate are the main contaminants found in transformer oil, affecting the quality of the oil through reduced insulation. Acid that forms in the oil when reacting with oxygen is called oxidization. It reduces the heat dissipation of the transformer as the acid forms sludge which settles on the windings of the transformer. The first step in the preventive maintenance program associated with transformer oil is the testing of the oil. The base line is established through initial testing, and subsequent annual testing identifies any changes. The minimal requirements are: (1) dielectric breakdown, a measure of the voltage conducted by the oil; (2) neutralization/acid number, which detects the level of acid present in the oil; (3) interfacial tension, which identifies the presence of polar compounds; (4) colour, which displays quality, aging and the presence of contaminants; and (5) water, which decreases the dielectric breakdown voltage. The analysis of the gases present in the oil is another useful tool in a maintenance program for the determination of a possible fault such as arcing, corona or overheated connections and is accomplished through Dissolved Gas Analysis (DGA). Remediation treatment includes upgrading the oil. Ideally, reclamation should be performed in the early stages of the acid buildup before sludging occurs. Onsite reclamation includes Fuller's earth processing and degasification, a process briefly described by the author.

Oil mixing behavior after an oil spill: identification conflicts of different fingerprints.

Science.gov (United States)

He, Shijie; Yu, Hongjun; Luo, Yongming; Wang, Chuanyuan; Li, Xueshuang; Li, Zhongping

2018-04-01

Clearing up whether spilled oil is mixed or not can strengthen the accuracy of oil spill identification. In the present study, the biomarkers in spilled oil samples were detected. The weathering modes of different types of diagnostic ratio and carbon isotope values of individual n-alkanes were also analyzed. The results showed that the diagnostic ratios of steroids, terpenes and aromatics, and weathering characteristics of carbon isotope composition (δ 13 C) of individual n-alkanes supported the idea that Dalian oil spill emerged from a single oil source. Furthermore, commonly used diagnostic ratios of n-alkanes indicated that the Dalian oil spill had undergone the oil mixing process. The different identifying outcomes indicate that some kinds of n-alkane-rich substance (such as oil dispersants) were mixed in the Dalian spilled oil and interfered with the routine diagnosis ratios of n-alkanes.

Stabilization of Softwood-Derived Pyrolysis Oils for Continuous Bio-oil Hydroprocessing

Energy Technology Data Exchange (ETDEWEB)

Olarte, Mariefel V.; Zacher, Alan H.; Padmaperuma, Asanga B.; Burton, Sarah D.; Job, Heather M.; Lemmon, Teresa L.; Swita, Marie S.; Rotness, Leslie J.; Neuenschwander, Gary N.; Frye, John G.; Elliott, Douglas C.

2015-10-15

The use of fast pyrolysis as a potential renewable liquid transportation fuel alternative to crude oil depends on successful catalytic upgrading to produce a refinery-ready product with oxygen content and qualities (i.e. specific functional group or compound content) that is compatible with the product’s proposed insertion point. Catalytic upgrading of bio-oil requires high temperature and pressure, while similar to crude oil hydrotreating, is not as straightforward for the thermally unstable pyrolysis oil. For years, a two-temperature zone, downflow trickle bed reactor was the state-of-the art for continuous operation. However, pressure excursion due to plug formation still occurred, typically at the high temperature transition zone, leading to a process shutdown within 140 h. Recently, a bio-oil pre-treatment process, together with a robust commercial catalyst, was found to be enabling the continuous operation of the two-zone hydroprocessing system. Here, we report the results on pre-treating bio-oil at 413 K and 8.4 MPa of flowing H2 (500 L H2/L bio-oil, 0.5 L bio-oil/L catalyst bed) and the attempts to characterize this oil product to understand the chemistry which enabled the long-term processing of bio-oil.

Kolkhoung (Pistacia khinjuk) Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability 
and Nutritional Value.

Science.gov (United States)

Asnaashari, Maryam; Hashemi, Seyed Mohammad Bagher; Mehr, Hamed Mahdavian; Yousefabad, Seyed Hossein Asadi

2015-03-01

In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high-performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel) and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well--balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation-sensitive oils to improve their shelf life.

Oil/gas collector/separator for underwater oil leaks

International Nuclear Information System (INIS)

Henning, C.D.

1993-01-01

An oil/gas collector/separator for underwater oil leaks is described comprising: a cylindrical tank; a hollow float member for supporting said tank in a substantially upright position; a skirt assembly secured to said hollow float member and extending in a direction away from said float member opposite said tank; means for removing oil from said tank; and means for removing gas from said tank

Canada's crude oil resources : crude oil in our daily lives

International Nuclear Information System (INIS)

Bott, R.

2001-10-01

Created in 1975, the Petroleum Communication Foundation is a not-for-profit organization. The objective of the Foundation is to inform Canadians about the petroleum industry in Canada. It produces educational, fact-based publications and programs, employing a multi-stakeholder review process. The first section of this publication is devoted to crude oil and the benefits that are derived from it. It begins by providing a brief definition of crude oil, then moves to the many uses in our daily lives and the environmental impacts like air pollution, spills, and footprint on the land from exploration and production activities. Section 2 details the many uses of crude oil and identifies the major oil producing regions of Canada. A quick mention is made of non-conventional sources of crude oil. The search for crude oil is the topic of section 3 of the document, providing an overview of the exploration activities, the access rights that must be obtained before gaining access to the resource. The drilling of oil is discussed in section 4. Section 5 deals with issues pertaining to reservoirs within rocks, while section 6 covers the feeding of the refineries, discussing topics from the movement of oil to market to the refining of the crude oil, and the pricing issues. In section 7, the uncertain future is examined with a view of balancing the supply and demand, as crude oil is a non-renewable resource. Supplementary information is provided concerning additional publications published by various organizations and agencies. figs

Intrastate conflict in oil producing states: A threat to global oil supply?

International Nuclear Information System (INIS)

Toft, Peter

2011-01-01

In this paper I investigate how often and how much outbreaks of intrastate conflict in oil producing states translates into oil supply shortfalls. The Libyan conflict that broke out in February 2011 highlighted the fear that intrastate conflict in oil producing states may imply shortfalls and ensuing volatile global oil prices. I argue, however, that it is far from certain that shortfalls following conflict outbreak will occur, since both sides in a conflict face incentives simultaneously to protect and maintain oil installations and to strike and destroy these. Based on a quantitative analysis of 39 intrastate wars in oil producing countries (1965-2007) I conclude that outbreak of conflict does not translate into production decline with any certainty. In fact, likelihoods are less than 50% for reductions to occur. In many cases growing production actually followed conflict outbreak. I conclude by investigating four characteristics of intrastate conflict that may explain when oil production is at risk during conflict: (1) proximity of oil producing fields to key battle zones, (2) duration of conflict, (3) separatism and the location of oil in separatist territory, and (4) the relative size of oil production. While the first three factors did not prove important, oil producer size could be significant. But further research is needed to establish this with greater certainty. - Highlights: → Oil shortfall during intrastate conflict is not a given. → Statistical analysis of 39 intrastate conflicts in oil producing countries since 1965. → Examination of four characteristics of intrastate conflict in oil producing countries. → Marginal significance related to large producers and production shortfall.

Intrastate conflict in oil producing states: A threat to global oil supply?

Energy Technology Data Exchange (ETDEWEB)

Toft, Peter, E-mail: peter.toft@ec.europa.eu [Institute for Energy, Joint Research Centre of the European Commission, Westerduinweg 3, 1755 ZG Petten (Netherlands)

2011-11-15

In this paper I investigate how often and how much outbreaks of intrastate conflict in oil producing states translates into oil supply shortfalls. The Libyan conflict that broke out in February 2011 highlighted the fear that intrastate conflict in oil producing states may imply shortfalls and ensuing volatile global oil prices. I argue, however, that it is far from certain that shortfalls following conflict outbreak will occur, since both sides in a conflict face incentives simultaneously to protect and maintain oil installations and to strike and destroy these. Based on a quantitative analysis of 39 intrastate wars in oil producing countries (1965-2007) I conclude that outbreak of conflict does not translate into production decline with any certainty. In fact, likelihoods are less than 50% for reductions to occur. In many cases growing production actually followed conflict outbreak. I conclude by investigating four characteristics of intrastate conflict that may explain when oil production is at risk during conflict: (1) proximity of oil producing fields to key battle zones, (2) duration of conflict, (3) separatism and the location of oil in separatist territory, and (4) the relative size of oil production. While the first three factors did not prove important, oil producer size could be significant. But further research is needed to establish this with greater certainty. - Highlights: > Oil shortfall during intrastate conflict is not a given. > Statistical analysis of 39 intrastate conflicts in oil producing countries since 1965. > Examination of four characteristics of intrastate conflict in oil producing countries. > Marginal significance related to large producers and production shortfall.

Characterization of Oxidative Stability of Fish Oil- and Plant Oil-Enriched Skimmed Milk

DEFF Research Database (Denmark)

Saga, Linda C.; Kristinova, Vera; Kirkhus, Bente

2013-01-01

oat oil and camelina oil to protect fish oil in bulk and as fish oil-enriched skimmed milk emulsions was evaluated. Results of oxidative stability of bulk oils and blends assessed by the Schaal oven weight gain test and by the rancimat method showed significant increase in oxidative stability when oat...... oil was added to fish oil in only 5 and 10 %, whereas no protective effect of camelina oil was observed when evaluated by these methods. Moreover, fish oil blended with oat oil conferred the lowest PV and lower amounts of volatile compounds during the storage period of 14 days at 4 °C. Surprisingly......, skimmed milk supplemented with fish-oat oil blend gave the highest scores for off-flavors in the sensory evaluation, demonstrating that several methods, including sensory analysis, should be combined to illustrate the complete picture of lipid oxidation in emulsions....

Comparison between jojoba oil and other vegetable oils as a substitute to petroleum

Energy Technology Data Exchange (ETDEWEB)

El Kinawy, O. [National Research centre, Dokki, Cairo (Egypt)

2004-06-15

Jojoba oil and other vegetable oils, such as soybean, sunflower and castor oils, were evaluated to be used as lubricants. Three standard mineral lubricating oils were considered in this study as reference. The essential parameters tested for comparison were the oil viscosity, viscosity index, and viscosity--temperature and shear rate--shear stress relationships. The effect of excessive heating on the vegetable oils' stability was studied and the corresponding parameters were also measured. Jojoba oil was found to be the best among all tested oils, whereas it gave the minimum change in viscosity gradient and hence the highest viscosity index. There was a linear relation between shear rate and shear stress of all oils before and after heat deterioration. Therefore, these oils were considered as Newtonion liquids. However, the oil viscosity, as well as the rate of viscosity variation with temperature, ({delta}{sup '}{eta}/{delta}{tau}) were affected by heat deterioration being lowered in value, in case of jojoba oil, and higher value, in case of castor oil. Jojoba oil was examined for other important properties for its use as a lubricant, such as refractive index, acid value, peroxide value, saponification value, iodine value, flash, fire and pour points. (author)

The Study of the Desulfurization Process of Oil and Oil Products of "Zhanazhol" Oil Field Using the Approaches of Green Chemistry

OpenAIRE

Zhaksyntay K. Kairbekov; Zhannur K. Myltykbaeva; Nazym T. Smagulova; Dariya K. Kanseitova

2015-01-01

In this paper we studied sono catalytic oxidative desulfurization of oil and diesel fraction from “Zhanazhol” oil deposits. We have established that the combined effect of the ultrasonic field and oxidant (ozone-air mixture) in the presence of the catalyst on the oil is potentially very effective method of desulfurization of oil and oil products. This method allows increasing the degree of desulfurization of oil by 62%.

Assessment of an oil palm population from Nigerian Institute for Oil ...

African Journals Online (AJOL)

Oil palm (Elaeis guineensis Jacq.), a monocotyledonous plant belonging to the Arecaceae family, is one of the most important oil crops in the world. In Nigeria, oil palm has benefited immensely from conventional breeding efforts resulting in high yields that have been achieved with this breeding material. However, oil palm ...

Quantification of rice bran oil in oil blends

Directory of Open Access Journals (Sweden)

Mishra, R.

2012-03-01

Full Text Available Blends consisting of physically refined rice bran oil (PRBO: sunflower oil (SnF and PRBO: safflower oil (SAF in different proportions were analyzed for various physicochemical parameters. The quantification of pure rice bran oil in the blended oils was carried out using different methods including gas chromatographic, HPLC, ultrasonic velocity and methods based on physico-chemical parameters. The physicochemical parameters such as ultrasonic velocity, relative association and acoustic impedance at 2 MHz, iodine value, palmitic acid content and oryzanol content reflected significant changes with increased proportions of PRBO in the blended oils. These parameters were selected as dependent parameters and % PRBO proportion was selected as independent parameters. The study revealed that regression equations based on the oryzanol content, palmitic acid composition, ultrasonic velocity, relative association, acoustic impedance, and iodine value can be used for the quantification of rice bran oil in blended oils. The rice bran oil can easily be quantified in the blended oils based on the oryzanol content by HPLC even at a 1% level. The palmitic acid content in blended oils can also be used as an indicator to quantify rice bran oil at or above the 20% level in blended oils whereas the method based on ultrasonic velocity, acoustic impedance and relative association showed initial promise in the quantification of rice bran oil.

Se analizaron diversos parámetros físico-químicos para la evaluación de mezclas de aceites en diferentes proporciones que incluyen: aceite de salvado de arroz físícamente refinado (PRBO: aceite de girasol (SNF y las mezclas PRBO: aceite de cártamo (SAF en diferentes proporciones. La cuantificación de la presencia del aceite de salvado de arroz en las mezclas se llevó a cabo por diferentes métodos, como cromatografía de gases (GC, cromatografía líquida (HPLC, ultrasonidos y métodos basados en otros parámetros f

The oil market

International Nuclear Information System (INIS)

Amic, E.; Lautard, P.

1999-01-01

This chapter examines the structure of the oil industry and the impacts of the oil markets on the hedging strategies of the energy consumers, the oil company, and the energy derivatives' provider. An introduction to market perspectives is presented, and the hedging operations in the jet fuel market in the airline sector are discussed. Trading and risk management within an oil company, the derivatives provider, trading derivatives in a multi-dimensional world, locational risks, and the modelling of term structure and the role of storage are considered. Industrial spreads and the role of refining, future market developments and market strategies for crude oil and oil products, and marketing packages and market risk are addressed

[Laser induced fluorescence spectrum characteristics of common edible oil and fried cooking oil].

Science.gov (United States)

Mu, Tao-tao; Chen, Si-ying; Zhang, Yin-chao; Chen, He; Guo, Pan; Ge, Xian-ying; Gao, Li-lei

2013-09-01

In order to detect the trench oil the authors built a trench oil rapid detection system based on laser induced fluorescence detection technology. This system used 355 nm laser as excitation light source. The authors collected the fluorescence spectrum of a variety of edible oil and fried cooking oil (a kind of trench oil) and then set up a fluorescence spectrum database by taking advantage of the trench oil detection system It was found that the fluorescence characteristics of fried cooking oil and common edible oil were obviously different. Then it could easily realize the oil recognition and trench oil rapid detection by using principal component analysis and BP neural network, and the overall recognition rate could reach as high as 97.5%. Experiments showed that laser induced fluorescence spectrum technology was fast, non-contact, and highly sensitive. Combined with BP neural network, it would become a new technique to detect the trench oil.

Co-processing of standard gas oil and biocrude oil to hydrocarbon fuels

International Nuclear Information System (INIS)

Agblevor, Foster A.; Mante, O.; McClung, R.; Oyama, S.T.

2012-01-01

The major obstacle in thermochemical biomass conversion to hydrocarbon fuels using pyrolysis has been the high oxygen content and the poor stability of the product oils, which cause them to solidify during secondary processing. We have developed a fractional catalytic pyrolysis process to convert biomass feedstocks into a product termed “biocrude oils” (stable biomass pyrolysis oils) which are distinct from unstable conventional pyrolysis oils. The biocrude oils are stable, low viscosity liquids that are storable at ambient conditions without any significant increases in viscosity; distillable at both atmospheric pressure and under vacuum without char or solid formation. About 15 wt% biocrude oils containing 20–25% oxygen were blended with 85 wt% standard gas oil and co-cracked in an Advanced Catalyst Evaluation (ACE™) unit using fluid catalytic cracking (FCC) catalysts to produce hydrocarbon fuels that contain negligible amount of oxygen. For the same conversion of 70% for both the standard gas oil and the biocrude oil/gas oil blends, the product gasoline yield was 44 wt%, light cycle oil (LCO) 17 wt%, heavy cycle oil (HCO) 13 wt%, and liquefied petroleum gas (LPG) 16 wt%. However, the coke yield for the standard gas oil was 7.06 wt% compared to 6.64–6.81 wt% for the blends. There appeared to be hydrogen transfer from the cracking of the standard gas oil to the biocrude oil which subsequently eliminated the oxygen in the fuel without external hydrogen addition. We have demonstrated for the first time that biomass pyrolysis oils can be successfully converted into hydrocarbons without hydrogenation pretreatment. -- Highlights: ► The co-processed product had less than 1% oxygen content and contained biocarbons determined by 14 C analysis. ► The co-processing did not affect the yields of gasoline, LCO, and HCO. ► First demonstration of direct conversion of pyrolysis oils into drop-in hydrocarbon fuels.

Oil pollution

International Nuclear Information System (INIS)

Mankabady, Samir.

1994-08-01

Oil enters the marine environment when it is discharged, or has escaped, during transport, drilling, shipping, accidents, dumping and offshore operations. This book serves as a reference both on the various complex international operational and legal matters of oil pollution using examples such as the Exxon Valdez, the Braer and Lord Donaldson's report. The chapters include the development of international rules on the marine environment, the prevention of marine pollution from shipping activities, liability for oil pollution damage, the conflict of the 1990 Oil Pollution Act and the 1992 protocols and finally the cooperation and response to pollution incidents. (UK)

Do oil dispersants make spilled oil more toxic to fish?

International Nuclear Information System (INIS)

Hodson, P.

2010-01-01

The Deepwater Horizon blowout in the Gulf of Mexico was the world's largest oil spill in terms of duration and volume spilled. Clean-up operations, which involved the continuous and wide-spread use of oil dispersant at the surface and at the seabed discharge point at 1500 metres depth, gave rise to public concern about dispersant toxicity. Reports from the United States Environmental Protection Agency (EPA) claimed little difference in acute toxicity to marine fish and invertebrate species among commonly available dispersants and between dispersed and non-dispersed Louisiana Sweet Crude. Technically, the toxicity of waterborne hydrocarbons does not vary with chemical dispersion. However, the EPA omitted any consideration of loading, and misled the public about the risks of dispersant use in oil clean-up. This study examined the chronic toxicity of dispersed oil to fish embryos. The study revealed that toxicity expressed as oil loading increases by a factor of 10 to 1000 times with dispersion, largely because 10 to 1000 times more oil enters the water column. Since the action of dispersant is on the exposure component of the risk equation, not on the potency of the toxic components of oil, then the risk of oil toxicity to fish increases an equivalent amount.

Influence of Oil Viscosity on Alkaline Flooding for Enhanced Heavy Oil Recovery

Directory of Open Access Journals (Sweden)

Yong Du

2013-01-01

Full Text Available Oil viscosity was studied as an important factor for alkaline flooding based on the mechanism of “water drops” flow. Alkaline flooding for two oil samples with different viscosities but similar acid numbers was compared. Besides, series flooding tests for the same oil sample were conducted at different temperatures and permeabilities. The results of flooding tests indicated that a high tertiary oil recovery could be achieved only in the low-permeability (approximately 500 mD sandpacks for the low-viscosity heavy oil (Zhuangxi, 390 mPa·s; however, the high-viscosity heavy oil (Chenzhuang, 3450 mPa·s performed well in both the low- and medium-permeability (approximately 1000 mD sandpacks. In addition, the results of flooding tests for the same oil at different temperatures also indicated that the oil viscosity put a similar effect on alkaline flooding. Therefore, oil with a high-viscosity is favorable for alkaline flooding. The microscopic flooding test indicated that the water drops produced during alkaline flooding for oils with different viscosities differed significantly in their sizes, which might influence the flow behaviors and therefore the sweep efficiencies of alkaline fluids. This study provides an evidence for the feasibility of the development of high-viscosity heavy oil using alkaline flooding.

The Russian oil

International Nuclear Information System (INIS)

Rucker, Laurent

2003-01-01

This article proposes a brief discussion of various assessments of Russian oil reserves, of the evolutions of Russian oil production (Russia is the second world producer after Saudi Arabia), of the distribution of Russian oil exports among various regions, and of the decrease of Russian oil consumption between 1992 and 2002. It describes the evolution of the actor system as the oil sector has been largely privatised since 1992, and indicates the main companies which should control the Russia market on a medium term. It also discusses the obstacles for the development of Production Sharing Agreements (PSA) between these companies. It addresses the issue of modernisation of the oil transport system as its status and its condition are often an obstacle to oil export for Russian companies. The article finally discusses the price issue, the relationship between Russia and other OPEC countries, and the need for huge investments

A Study on the efficient alleviation of domestic oil price at international oil crisis

Energy Technology Data Exchange (ETDEWEB)

Lee, Young Ku [Korea Energy Economics Institute, Euiwang (Korea)

1999-01-01

For alleviating domestic oil price when the international oil crisis happens, the government has been reacted directly such as using stored oil or alleviation fund. Although the release of stored oil works for short-term depending on the type of crisis, concerning that most of oil crisis had been resulted in temporary supply reduction rather than long-term supply suspension, utilizing the domestic alleviation fund is regarded more economical than storing oil. However, it has been suggested to compare efficiencies of alleviation fund and a futures market regarding the perspectives that using alleviation fund is more inefficient than utilizing a futures market. Moreover, the direct management by government is less efficient than indirect management. As an efficient way to alleviate domestic oil price at international oil crisis, this study presents an effective utilization of trading in futures of crude oil. There is a high probability of occurrence of this kind of oil crisis by judging from the world political situation and the trend of oil market. In such a case, the government as a crude oil importer should minimize the stored oil and utilize a futures market effectively. The subject of alleviating oil price by trading in futures is an oil supplier, such as oil refining companies or oil importers not the government as a prerequisite. Furthermore, the government should approve to include appropriate cost for preparing oil price alleviation in the oil price and it is required that such a government policy should be consistent. (author). 41 refs., 3 figs., 15 Tabs.

Process for separating and recovering oil from oil-sands, etc

Energy Technology Data Exchange (ETDEWEB)

Preller, H

1921-02-24

A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil-shale, and coal, according to Patent 400,122, is described. It is characterized in that the mined material falling on account of its weight is exposed to the running hot water in circulation through the wash-chamber and the clarifying chamber arranged separate or built on (circulation) being obtained by pumps or injectors in a regulatable motion.

Spectroscopic investigation of the wettability of multilayer graphene using highly ordered pyrolytic graphite as a model material.

Science.gov (United States)

Ashraf, Ali; Wu, Yanbin; Wang, Michael C; Aluru, Narayana R; Dastgheib, Seyed A; Nam, SungWoo

2014-11-04

We report the intrinsic water contact angle (WCA) of multilayer graphene, explore different methods of cleaning multilayer graphene, and evaluate the efficiency of those methods on the basis of spectroscopic analysis. Highly ordered pyrolytic graphite (HOPG) was used as a model material system to study the wettability of the multilayer graphene surface by WCA measurements. A WCA value of 45° ± 3° was measured for a clean HOPG surface, which can serve as the intrinsic WCA for multilayer graphene. A 1 min plasma treatment (100 W) decreased the WCA to 6°, owing to the creation of surface defects and functionalization by oxygen-containing groups. Molecular dynamics simulations of water droplets on the HOPG surface with or without the oxygen-containing defect sites confirmed the experimental results. Heat treatment at near atmospheric pressure and wet chemical cleaning methods using hydrofluoric acid and chloroform did not change the WCA significantly. Low-pressure, high-temperature annealing under argon and hydrogen reduced the WCA to 54°, close to the intrinsic WCA of HOPG. Raman spectroscopy and atomic force microscopy did not show any significant change for the HOPG surface after this treatment, confirming low-pressure, high-temperature annealing as an effective technique to clean multilayer graphene without damaging the surface. Time-of-flight secondary ion mass spectrometry indicated the existence of hydrocarbon species on the surface of the HOPG sample that was exposed to air for <5 min and the absence of these impurities in the bulk. X-ray photoelectron spectroscopy analyses of the sample surfaces after the different cleaning techniques were performed to correlate the WCA to the surface chemistry. X-ray photoelectron spectroscopy results revealed that the WCA value changed drastically, depending on the amounts of oxygen-containing and hydrocarbon-containing groups on the surface.

Nylon 6,6 Nonwoven Fabric Separates Oil Contaminates from Oil-in-Water Emulsions.

Directory of Open Access Journals (Sweden)

Ryan A Ortega

Full Text Available Industrial oil spills into aquatic environments can have catastrophic environmental effects. First responders to oil spills along the coast of the Gulf of Mexico in the southern United States have used spunbond nylon fabric bags and fences to separate spilled oil and oil waste from contaminated water. Low area mass density spunbond nylon is capable of sorbing more than 16 times its mass in low viscosity crude oil and more than 26 times its mass in higher viscosity gear lube oil. Nylon bags separated more than 95% of gear lube oil contaminate from a 4.5% oil-in-water emulsion. Field testing of spunbond nylon fences by oil spill first responders has demonstrated the ability of this material to contain the oily contaminate while allowing water to flow through. We hypothesize that the effectiveness of nylon as an oil filter is due to the fact that it is both more oleophilic and more hydrophilic than other commonly used oil separation materials. The nylon traps oil droplets within the fabric or on the surface, while water droplets are free to flow through the fabric to the water on the opposite side of the fabric.

Spilled oil and infaunal activity - Modification of burrowing behavior and redistribution of oil

Science.gov (United States)

Clifton, H.E.; Kvenvolden, K.A.; Rapp, J.B.

1984-01-01

A series of experiments in Willapa Bay, Washington, indicates the degree to which the presence of spilled oil modifies the burrowing behavior of infauna and the extent to which the animals redistribute oil into intertidal sediment. Small amounts of North Slope crude oil introduced at low tide directly into burrow openings (mostly made by the crustacean Callianassa) resulted in a limited and temporary reduction in the number of burrow openings. In contrast, a layer of oil-saturated sand 1 cm thick buried about 5 cm below the sediment surface sharply reduced the number of burrow openings. After a year, the few new burrows penetrated only the margins of the experimental plot, and bioturbation below the buried oil-saturated sand layer declined dramatically. The experiments suggest that small amounts of oil temporarily stranded by tides in themselves have no long-range effect on burrowing behavior. The fauna, however, are capable of introducing measurable amounts of oil into the subsurface, where it is retained long after the rest of the stranded oil had washed away. A buried layer of oil-saturated sand greatly reduces infaunal activity; the oil presents an effective barrier that can persist for years. The oil incorporated into the sediment from burrow openings showed evidence of degradation after 7 months. In contrast the layer of buried oil remained essentially undergraded after a period of two years, even though oil in lower concentrations above the layer was degraded after a period of one year. This variation in degree of degradation of the buried oil, as well as the heterogeneity of oil distribution wherever the oil has been incorporated from the surface, emphasises the importance of careful sampling in any attempt to locate or monitor the presence of spilled oil in the substrate.In a series of experiments in Willapa Bay, Washington, small amounts of North Slope crude oil introduced at low tide directly into burrow openings resulted in a limited and temporary

Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

Energy Technology Data Exchange (ETDEWEB)

Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

2015-09-30

This report summarizes the significant findings from the Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources program sponsored by the Department of Energy through the National Energy Technology Laboratory. There were four principle areas of research; Environmental, legal, and policy issues related to development of oil shale and oil sands resources; Economic and environmental assessment of domestic unconventional fuels industry; Basin-scale assessment of conventional and unconventional fuel development impacts; and Liquid fuel production by in situ thermal processing of oil shale Multiple research projects were conducted in each area and the results have been communicated via sponsored conferences, conference presentations, invited talks, interviews with the media, numerous topical reports, journal publications, and a book that summarizes much of the oil shale research relating to Utah’s Uinta Basin. In addition, a repository of materials related to oil shale and oil sands has been created within the University of Utah’s Institutional Repository, including the materials generated during this research program. Below is a listing of all topical and progress reports generated by this project and submitted to the Office of Science and Technical Information (OSTI). A listing of all peer-reviewed publications generated as a result of this project is included at the end of this report; Geomechanical and Fluid Transport Properties 1 (December, 2015); Validation Results for Core-Scale Oil Shale Pyrolysis (February, 2015); and Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach (November, 2014); Policy Issues Associated With Using Simulation to Assess Environmental Impacts (November, 2014); Policy Analysis of the Canadian Oil Sands Experience (September, 2013); V-UQ of Generation 1 Simulator with AMSO Experimental Data (August, 2013); Lands with Wilderness Characteristics, Resource Management Plan Constraints, and Land Exchanges

Quality control of mixtures consisting of engine oil and rapeseed oil by means of online oil sensors; Qualitaetsueberwachung von Motoroel-Rapsoelmischungen mit Online-Oelsensoren. Labortests

Energy Technology Data Exchange (ETDEWEB)

Thuneke, Klaus; Schreiber, Katja [Technologie- und Foerderzentrum, Straubing (Germany)

2013-10-01

It was the goal of the work to investigate interactions between motor oils and rapeseed oil fuel and to test oil sensors for monitoring the quality of aged mixtures of motor oil and rapeseed oil. At first oil samples were aged in the laboratory, whereby motor oil type, share of rapeseed oil and aeration was varied. Depending on type of engine oil different ageing effects were noticed. Higher shares of rapeseed and aeration stimulate increase of viscosity and acid value. In a further step online oil sensors were tested in both, a model of a lubrication system and a test engine. The signals of the sensors plausibly described the oil ageing process by the indicators dynamic or acoustic viscosity, permittivity number, specific electric conductivity. In particular viscosity and permittivity are suitable for showing changes in different motor oil rapeseed oil mixtures during oil ageing. However, for a reliable control system detecting critical rapeseed oil enrichment in the motor oil onboard, further work has to be done. (orig.)

Electricity/oil substitution

International Nuclear Information System (INIS)

Melvin, J.G.

1980-09-01

The extent to which electricity could substitute for imported oil in Canada is assessed and it is concluded that the bulk of projected oil imports could be displaced. This substitution of electricity for oil could be largely completed within two decades, with existing technology, using Canadian resources. The substitution of electricity for imported oil would result in relatively low energy costs and would stimulate economic growth. Energy self-sufficiency through the substitution of electricity for oil is uniquely a Canadian option; it is not open to other industrial countries. The option exists because of Canada's resources of oil sands for essential liquid fuels, hydraulic and nuclear electrical potential, and natural gas as an interim source of energy. While other countries face an energy crisis due to declining supplies of oil, Canada faces opportunities. The policies of Federal and Provincial governments, as perceived by individual decision makers, will have a major influence on Canada's ability to realize opportunities. (auth)

An Estimate of Recoverable Heavy Oil Resources of the Orinoco Oil Belt, Venezuela

Science.gov (United States)

Schenk, Christopher J.; Cook, Troy A.; Charpentier, Ronald R.; Pollastro, Richard M.; Klett, Timothy R.; Tennyson, Marilyn E.; Kirschbaum, Mark A.; Brownfield, Michael E.; Pitman, Janet K.

2009-01-01

The Orinoco Oil Belt Assessment Unit of the La Luna-Quercual Total Petroleum System encompasses approximately 50,000 km2 of the East Venezuela Basin Province that is underlain by more than 1 trillion barrels of heavy oil-in-place. As part of a program directed at estimating the technically recoverable oil and gas resources of priority petroleum basins worldwide, the U.S. Geological Survey estimated the recoverable oil resources of the Orinoco Oil Belt Assessment Unit. This estimate relied mainly on published geologic and engineering data for reservoirs (net oil-saturated sandstone thickness and extent), petrophysical properties (porosity, water saturation, and formation volume factors), recovery factors determined by pilot projects, and estimates of volumes of oil-in-place. The U.S. Geological Survey estimated a mean volume of 513 billion barrels of technically recoverable heavy oil in the Orinoco Oil Belt Assessment Unit of the East Venezuela Basin Province; the range is 380 to 652 billion barrels. The Orinoco Oil Belt Assessment Unit thus contains one of the largest recoverable oil accumulations in the world.

A photometric method for the estimation of the oil yield of oil shale

Science.gov (United States)

Cuttitta, Frank

1951-01-01

A method is presented for the distillation and photometric estimation of the oil yield of oil-bearing shales. The oil shale is distilled in a closed test tube and the oil extracted with toluene. The optical density of the toluene extract is used in the estimation of oil content and is converted to percentage of oil by reference to a standard curve. This curve is obtained by relating the oil yields determined by the Fischer assay method to the optical density of the toluene extract of the oil evolved by the new procedure. The new method gives results similar to those obtained by the Fischer assay method in a much shorter time. The applicability of the new method to oil-bearing shale and phosphatic shale has been tested.

Effects of oil and oil burn residues on seabird feathers

DEFF Research Database (Denmark)

Fritt-Rasmussen, Janne; Linnebjerg, Jannie Fries; Sørensen, Martin X.

2016-01-01

It is well known, that in case of oil spill, seabirds are among the groups of animals most vulnerable. Even small amounts of oil can have lethal effects by destroying the waterproofing of their plumage, leading to loss of insulation and buoyancy. In the Arctic these impacts are intensified....... To protect seabirds, a rapid removal of oil is crucial and in situ burning could be an efficient method. In the present work exposure effects of oil and burn residue in different doses was studied on seabird feathers from legally hunted Common eider (Somateria mollissima) by examining changes in total weight...... of the feather and damages on the microstructure (Amalgamation Index) of the feathers before and after exposure. The results of the experiments indicate that burn residues from in situ burning of an oil spill have similar or larger fouling and damaging effects on seabird feathers, as compared to fresh oil....

Effects on bread and oil quality after functionalization with microencapsulated chia oil.

Science.gov (United States)

González, Agustín; Martínez, Marcela L; León, Alberto E; Ribotta, Pablo D

2018-03-23

Omega-3 and omega-6 fatty acids-rich oils suffer oxidation reactions that alter their chemical and organoleptic quality. Microencapsulation can be a powerful tool for protection against ambient conditions. In the present study, the addition of microencapsulated chia oil as an ingredient in bread preparations and its effect on the technological and chemical quality of breads was investigated. Microencapsulation of chia oil was carried out by freeze-drying with soy proteins as wall material and oil release was determined under in vitro gastric and intestinal conditions. Encapsulated oil-containing bread showed no differences in specific volume, average cell area, firmness and chewiness with respect to control bread. Unencapsulated oil-containing bread showed a marked increase in hydroperoxide values respect to control, whereas encapsulated oil-containing bread values were not affected by baking and bread storage. The fatty acid profiles showed a decrease of 13% and 16%, respectively, in α-linolenic acid in the encapsulated and unencapsulated oils with respect to bulk chia oil. Sensory analysis showed no significant differences between bread samples. The addition of encapsulated chia oil did not alter the technological quality of breads and prevented the formation of hydroperoxide radicals. A ration of encapsulated oil-containing bread contributes 60% of the recommended dietary intake of omega-3 fatty acids. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Oil sands and heavy oil development issues and prospects under a Liberal government

International Nuclear Information System (INIS)

Shiry, J.

1993-01-01

A short review is presented of some of the factors affecting development of the western Canadian oil sands and heavy oil deposits to the year 2000. The Alberta oil sands resource has at least 1 trillion bbl of recoverable oil. At current prices, technology is the key to reducing costs to a more economic level. Cash operating costs have halved to $15/bbl over the past decade and the oil sands companies have programs to halve that figure again. A problem is the rising cost of natural gas as a fuel, which could jeopardize further development of both oil sand and heavy oil resources. In Saskatchewan, over 25 billion bbl of heavy oil are estimated to be in place. The biggest question is what percentage can be recovered; again, technology such as horizontal wells, 3-dimensional seismic, and steam assisted recovery is playing an important role. Concerns are expressed about the intentions of the new Liberal government concerning oil sand/heavy oil development, especially on the issues of foreign investment, exports, and environmental policy. A Liberal energy policy is not likely to allow U.S. direct investment in an oil sands plant to be tied to export of production, and the energy- and emissions-intensive nature of the oil sand/heavy oil industry will tend to make environmental approvals difficult

Oil shale technology

International Nuclear Information System (INIS)

Lee, S.

1991-01-01

Oil shale is undoubtedly an excellent energy source that has great abundance and world-wide distribution. Oil shale industries have seen ups and downs over more than 100 years, depending on the availability and price of conventional petroleum crudes. Market forces as well as environmental factors will greatly affect the interest in development of oil shale. Besides competing with conventional crude oil and natural gas, shale oil will have to compete favorably with coal-derived fuels for similar markets. Crude shale oil is obtained from oil shale by a relatively simple process called retorting. However, the process economics are greatly affected by the thermal efficiencies, the richness of shale, the mass transfer effectiveness, the conversion efficiency, the design of retort, the environmental post-treatment, etc. A great many process ideas and patents related to the oil shale pyrolysis have been developed; however, relatively few field and engineering data have been published. Due to the vast heterogeneity of oil shale and to the complexities of physicochemical process mechanisms, scientific or technological generalization of oil shale retorting is difficult to achieve. Dwindling supplied of worldwide petroleum reserves, as well as the unprecedented appetite of mankind for clean liquid fuel, has made the public concern for future energy market grow rapidly. the clean coal technology and the alternate fuel technology are currently of great significance not only to policy makers, but also to process and chemical researchers. In this book, efforts have been made to make a comprehensive text for the science and technology of oil shale utilization. Therefore, subjects dealing with the terminological definitions, geology and petrology, chemistry, characterization, process engineering, mathematical modeling, chemical reaction engineering, experimental methods, and statistical experimental design, etc. are covered in detail

Method of burning flammable radioactive wastes

International Nuclear Information System (INIS)

Yahata, Taneaki.

1980-01-01

Purpose: To completely oxidize flammable radioactive wastes such as organic compounds, ion exchange materials or oils. Method: Contaminated flammable radioactive wastes are heated and pyrolytically decomposed in the range 400 0 to 500 0 C in the presence of oxygen under lower pressure than atmospheric pressure. Volatile organic substance, hydrogen and soot subsequently produced are passed over oxidation catalyst. The catalysts such as copper oxide, iron oxide, cobalt oxide, nickel oxide, chromium oxide are heated in the range 600 0 to 700 0 C to produce stable oxides. (J.P.N.)

Utah Heavy Oil Program

Energy Technology Data Exchange (ETDEWEB)

J. Bauman; S. Burian; M. Deo; E. Eddings; R. Gani; R. Goel; C.K. Huang; M. Hogue; R. Keiter; L. Li; J. Ruple; T. Ring; P. Rose; M. Skliar; P.J. Smith; J.P. Spinti; P. Tiwari; J. Wilkey; K. Uchitel

2009-10-20

The Utah Heavy Oil Program (UHOP) was established in June 2006 to provide multidisciplinary research support to federal and state constituents for addressing the wide-ranging issues surrounding the creation of an industry for unconventional oil production in the United States. Additionally, UHOP was to serve as an on-going source of unbiased information to the nation surrounding technical, economic, legal and environmental aspects of developing heavy oil, oil sands, and oil shale resources. UHOP fulGilled its role by completing three tasks. First, in response to the Energy Policy Act of 2005 Section 369(p), UHOP published an update report to the 1987 technical and economic assessment of domestic heavy oil resources that was prepared by the Interstate Oil and Gas Compact Commission. The UHOP report, entitled 'A Technical, Economic, and Legal Assessment of North American Heavy Oil, Oil Sands, and Oil Shale Resources' was published in electronic and hard copy form in October 2007. Second, UHOP developed of a comprehensive, publicly accessible online repository of unconventional oil resources in North America based on the DSpace software platform. An interactive map was also developed as a source of geospatial information and as a means to interact with the repository from a geospatial setting. All documents uploaded to the repository are fully searchable by author, title, and keywords. Third, UHOP sponsored Give research projects related to unconventional fuels development. Two projects looked at issues associated with oil shale production, including oil shale pyrolysis kinetics, resource heterogeneity, and reservoir simulation. One project evaluated in situ production from Utah oil sands. Another project focused on water availability and produced water treatments. The last project considered commercial oil shale leasing from a policy, environmental, and economic perspective.

Financial oil derivatives: from options to oil warrants and synthetic oilfields

International Nuclear Information System (INIS)

Trabia, Xavier

1992-01-01

This study aims to shed light on some of the most interesting financial oil derivatives issued so far in order to assess the potential of this new wave of innovative funding instruments. In Part I some theoretical background is provided and applied to the problem of the American futures option. The ''binomial'' model for valuing future option contracts is presented and the most accurate alternatives for pricing American futures options are reviewed. The role of these numerical procedures in valuing more complex options involved in oil warrants is examined. Comments are made on the behaviour of volatility, which stands as a key interface between theory and practice in oil trading on the oil futures market. Part II of the study describes in detail some of the most famous new financial oil derivatives. Some final conclusions are drawn on the potential of oil trusts and synthetic oilfields to be involved in project and general funding in the oil industry. (44 figures, 11 tables, 53 references) (UK)

Effects of Crude Oil and Oil Products on Growth of Some Edible ...

African Journals Online (AJOL)

The vegetative growth response of three local edible mushrooms: Pleurotus pulmonarius (Pp), Pleurotus tuber-regium (Pt) and Lentinus squarrosulus (Ls) on different concentrations of Crude oil (COIL), Automotive Gasoline Oil (AGO), Fresh Engine Oil (ENGOIL) and Spent Engine Oil (SENGOIL) was investigated. The result ...

Oils; gas

Energy Technology Data Exchange (ETDEWEB)

Day, D T

1922-09-18

Oils and gas are obtained from shale or oil-bearing sand by immersing the shale in and passing it through a bath of liquid oil, cracking the oil-soaked shale, and condensing the vapor and using the condensate to replenish the bath, preferably by passing the gases and vapors direct into the oil-bath container. Shale is fed continuously from a hopper to a bath of oil in an inclined chamber, is carried to the outlet by a conveyer, and through cracking tubes to an outlet pipe by conveyers. The gases and vapors escape by the pipe, a part condensing in the chamber and a run-back pipe and replenishing the bath, and the remainder passing through a condensing tower and condenser connected to reservoirs; the gas is further passed through a scrubber and a pipe to the burner of the retort. The oil condensed in the chamber overflows to the reservoir through a pipe provided with an open pipe to prevent siphoning. The conveyers and a valve on the pipe are operated by gearing. The operation may be conducted at reduced, normal, or increased pressure, e.g., 70 lbs. The temperature of the retort should be about 900 to 1400/sup 0/F, that of the inside of the tubes about 550 to 700/sup 0/F, and that of the chamber about 300/sup 0/F. The chamber and pipe may be insulated or artificially cooled.

Seed oil content and selected qualitative parameters of oils from grape seeds

Directory of Open Access Journals (Sweden)

Vladimír Mašán

2017-01-01

Full Text Available Grape seed oil (Oleum vitis viniferae represents promising plant oil, which is used mainly in gastronomy and for pharmaceutical purposes as well as for various technical applications. In this paper, there were examined oil contents and oil quality properties of seeds taken from 8 grape cultivars. Oil contents were found to be different for each cultivar, which ranged from 11.5% (Dornfelder to 17.5% (Riesling. The results showed a dependence between the length of the growing season for individual varie-ties and the total content of oil in seeds. Fatty acid concentrations in the evaluated oil samples were in various ranges, while the highest values were determined in linoleic acid 70.10 to 71.55%, oleic acid 15.61 to 17.14%, palmitic acid 6.87 to 8.18% and stearic acid 3.16 to 3.90%. Saturated fatty acid values were lower than the values of monounsaturated fatty acids and polyunsaturated fatty acids in all oil samples. The degree of unsaturation in the grape seed oil ranged between 88.6 - 89.21%. Thanks to its content, grape seed oil can be considered as a food supplement improving the nutri-tional value of the human diet.

Olive oil adulterated with hazelnut oils: simulation to identify possible risks to allergic consumers

NARCIS (Netherlands)

Arlorio, M.; Coisson, J. D.; Bordiga, M.; Travaglia, F.; Garino, C.; Zuidmeer, L.; van Ree, R.; Giuffrida, M. G.; Conti, A.; Martelli, A.

2010-01-01

According to European Union Regulation EC 1531/2001, olive oil labelled as oextra-virgino should be cold-pressed and contain no refined oil or oil from other oleaginous seeds or nuts. Adulteration of extra virgin olive oil (EVOO) with hazelnut oil (HAO) is a serious concern both for oil suppliers

Contact Allergy to Neem Oil.

NARCIS (Netherlands)

de Groot, Anton; Jagtman, Berend A; Woutersen, Marjolijn

2018-01-01

A case of allergic contact dermatitis from neem oil is presented. Neem oil (synonyms: Melia azadirachta seed oil [INCI name], nim oil, margosa oil) is a vegetable (fixed) oil obtained from the seed of the neem tree Azadirachta indica by cold pressing. Contact allergy to neem oil has been described

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, Cutler J.; Kaufmann, Robert K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways

Oil supply and oil politics: Deja Vu all over again

International Nuclear Information System (INIS)

Cleveland, C.J.; Kaufmann, R.K.

2003-01-01

President Bush has identified US dependence on imported oil as an urgent energy, economic, and national security concern. The President's energy plan promotes the development of domestic resources, based on the assumption that economic incentives and the opening of frontier areas for exploration will increase domestic production. If realized, this will reduce dependence on imported oil and reduce OPEC's ability to affect aggregate oil supply and price. The evidence suggests, however, that this policy will not increase significantly US production of crude oil, will not reduce significantly OPEC's influence, and it will distort the US macroeconomy. Even if allowed, production from the Arctic National Wildlife Refuge will have a negligible impact on the world oil markets. Further subsidies to the oil industry will divert resources from other more productive investments. Conservation and energy efficiency merit greater emphasis in US energy policy given their ability to reduce the use of cost-effective and environmentally beneficial ways. (author)

Effects of fish oil type, lipid antioxidants and presence of rapeseed oil on oxidative flavour stability of fish oil enriched milk

DEFF Research Database (Denmark)

Bruni Let, Mette; Jacobsen, Charlotte; Meyer, Anne S.

2004-01-01

As a part of our ongoing experiments on optimization of the oxidative stability of fish oils in genuine food systems, this study investigated the oxidative deterioration of fish oil enriched milk emulsions during cold storage. The experimental data showed that addition of rapeseed oil to fish oil...... (1:1) prior to emulsification into milk significantly protected the emulsions against oxidative deterioration. Addition of propyl gallate and a citric acid ester to the fish oil prior to emulsification also protected the fish oil enriched milk during storage. Emulsions containing a rapeseed:fish oil...... mixture were oxidatively stable during 11 d at 2 øC. Thus, no additional inhibitory effect of the added antioxidants was observed. The peroxide value and concentrations of five selected volatiles derived from n- 3 PUFA degradation in rapeseed:fish oil mixture emulsions were not significantly different...

Oil market outlook

International Nuclear Information System (INIS)

Starling, Philip

1997-01-01

The role of the International Energy Agency's (IEA) ''OiMarket Report'' is described in terms of its response to and support for oil companies seeking to monitor short-term global oil market developments. The document is increasingly used for reference both by industry and governments. Data is compiled from oil companies, consultants, and government, and OECD countries provide supply/demand oil balance data by product grade on a monthly basic. (UK)

Biotransformation of natural gas and oil compounds associated with marine oil discharges.

Science.gov (United States)

Brakstad, Odd Gunnar; Almås, Inger K; Krause, Daniel Franklin

2017-09-01

Field data from the Deepwater Horizon (DWH) oil spill in the Gulf of Mexico (GoM) suggested that oxidation of gas compounds stimulated biodegradation of oil compounds in the deep sea plume. We performed experiments with local seawater from a Norwegian fjord to examine if the presence of dissolved gas compounds (methane, ethane and propane) affected biodegradation of volatile oil compounds, and if oil compounds likewise affected gas compound oxidation. The results from the experiment showed comparable oil compound biotransformation rates in seawater at 5 °C between seawater with and without soluble gases. Gas oxidation was not affected by the presence of volatile oil compounds. Contrary to DWH deep sea plume data, propane oxidation was not faster than methane oxidation. These data may reflect variations between biodegradation of oil and gas in seawater environments with different history of oil and gas exposure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycling of used oil

International Nuclear Information System (INIS)

Vipulanandan, C.; Ghurye, G.

1992-01-01

This paper reports on used oil which is a valuable resource that should be recycled. Recycling used oil saves energy and natural resources. Used oil can be reprocessed and used as fuel in industrial burners and boilers. Unfortunately, more than 400 million gallons/year of used oil is lost through widespread dumping, partly due to lack of effective recycling procedures. Although used oil is not currently a federally listed hazardous waste, the U.S. EPA has proposed to list it as a hazardous waste, which will make recycling of used oil even more attractive. Laboratory samples, representing used oil, were used for detailed parametric studies and to determine the limitation of extending some of the current physical separation techniques such as sedimentation and centrifuging developed for oil-water and solid-liquid separation

Research on a dispersing solution for burnt crude oils: Aegean Sea oil spill

International Nuclear Information System (INIS)

Bergueiro, J.R.; Morales, N.; Dominguez, F.

1993-01-01

The oil tanker Aegean Sea spilled oil when it grounded during severe storm conditions near La Coruna, Spain. Much of the oil burned after an explosion was caused by the hull breaking apart. Oil which contaminated several beaches was affected by both combustion and weathering. Experiments were conducted on oil sampled from the beaches to investigate dispersion of the oil using Beep Enersperse 1990 at different shaking speeds. Biodegradation experiments were also conducted in the presence of Beep Enersperse 1990 but with seawater absent. Although emulsification of the burnt and weathered oil was very difficult, good dispersion and biodegradation were obtained. After 42 d in a stirred reactor, biodegradation of the oil reached at least 80%. 3 refs., 3 figs., 4 tabs

Assessment of the relationship between oil prices and US oil stocks

International Nuclear Information System (INIS)

Saif Ghouri, Salman

2006-01-01

This paper qualitatively and quantitatively analyzes the relationship between US monthly ending oil stocks position with that of West Texas Intermediate (WTI) oil prices from February 1995 to July 2004. The paper concludes if other things are held constant, WTI is inversely related to the petroleum products (PPP), combined petroleum products and crude oil (CPPP), crude oil alone (Crude), total oil stocks including petroleum products, crude oil and strategic petroleum reserves SPR (Total), total gasoline (TGO), total distillate (TDO). It could not establish a statistically significant and negative relationship with SPR when run alone. One percent increase (decrease) in CPPP, PPP, Crude, Total, TGO and TDO leads to decrease (increase) in WTI, respectively, by 0.70, 0.43, 0.37, 0.97, 0.26 and 0.21 percent. Oil prices are largely influenced by total crude and Crude and PPP inventories levels while modestly with variations in gasoline and distillate stocks levels. Despite a healthy increase of over 22 percent in SPR from January 2001 to April 2004, it did not result in easing of oil prices. Primarily because SPR are meant for security of supply concern and are only released under extreme conditions by the President of United States, they are neither meant for the purposes of balancing supply-demand gap nor for the stability of oil prices. The aggressive SPR buildup in recent years is related to international terrorism, geopolitical situation in the Middle East, particularly in Iraq, that encourages US government to enhance its SPR to meet any short-term eventuality. The analyst must keep a close eye on CPPP and the total oil stocks variation to forecast WTI in the short run whilst gasoline and distillate influence oil prices modestly in the short run. SPR, on the other hand, are expected to play a pivotal role in balancing oil prices and in providing a critical resource for the economy in case of any major shortfall in the long run

Assessment of the relationship between oil prices and US oil stocks

Energy Technology Data Exchange (ETDEWEB)

Saif Ghouri, Salman [Business Environment Section, Corporate Planning Department, Qatar Petroleum, Doha (Qatar)]. E-mail: ghouri@qp.com.qa

2006-11-15

This paper qualitatively and quantitatively analyzes the relationship between US monthly ending oil stocks position with that of West Texas Intermediate (WTI) oil prices from February 1995 to July 2004. The paper concludes if other things are held constant, WTI is inversely related to the petroleum products (PPP), combined petroleum products and crude oil (CPPP), crude oil alone (Crude), total oil stocks including petroleum products, crude oil and strategic petroleum reserves SPR (Total), total gasoline (TGO), total distillate (TDO). It could not establish a statistically significant and negative relationship with SPR when run alone. One percent increase (decrease) in CPPP, PPP, Crude, Total, TGO and TDO leads to decrease (increase) in WTI, respectively, by 0.70, 0.43, 0.37, 0.97, 0.26 and 0.21 percent. Oil prices are largely influenced by total crude and Crude and PPP inventories levels while modestly with variations in gasoline and distillate stocks levels. Despite a healthy increase of over 22 percent in SPR from January 2001 to April 2004, it did not result in easing of oil prices. Primarily because SPR are meant for security of supply concern and are only released under extreme conditions by the President of United States, they are neither meant for the purposes of balancing supply-demand gap nor for the stability of oil prices. The aggressive SPR buildup in recent years is related to international terrorism, geopolitical situation in the Middle East, particularly in Iraq, that encourages US government to enhance its SPR to meet any short-term eventuality. The analyst must keep a close eye on CPPP and the total oil stocks variation to forecast WTI in the short run whilst gasoline and distillate influence oil prices modestly in the short run. SPR, on the other hand, are expected to play a pivotal role in balancing oil prices and in providing a critical resource for the economy in case of any major shortfall in the long run.

The effect of coconut oil and palm oil as substituted oils to cocoa butter on chocolate bar texture and melting point

Science.gov (United States)

Limbardo, Rebecca Putri; Santoso, Herry; Witono, Judy Retti

2017-05-01

Cocoa butter has responsibility for dispersion medium to create a stable chocolate bar. Due to the economic reason, cocoa butter is partially or wholly substituted by edible oils e.g palm oil and coconut oil. The objective of the research was to observe the effect of oil substitution in the chocolate bar towards its melting point and texture. The research were divided in three steps which were preliminary research started with fat content analysis in cocoa powder, melting point analysis of substituted oils anc cocoa butter, and iodine number analysis in vegetable fats (cocoa butter, coconut oil, and palm oil), chocolate bar production with substitution 0%, 20%, 40%, 60%, 80%, and 100%wt of cocoa butter with each of substituted oils, and analysis process to determine the chocolate bar melting point with DSC and chocolate bar hardness with texture analyser. The increasement of substituted oils during substitution in chocolate bar would reduce the melting point of chocolate bar from 33.5°C to 31.6°C in palm oil substitution with cocoa butter and 33.5°C to 30.75°C in coconut oil substitution. The hardness of chocolate with palm oil were around 88.5 to 139 g on the 1st cycle and 22.75 to 132 g on the 2nd cycle. The hardness of chocolate with coconut oil were around 74.75 to 152.5 g on the 1st cycle and 53.25 to 132 g on the 2nd cycle. Maximum amount of fats substitution to produce a stable texture chocolate bar is 60% wt.

Foam-oil interaction in porous media: implications for foam assisted enhanced oil recovery.

Science.gov (United States)

Farajzadeh, R; Andrianov, A; Krastev, R; Hirasaki, G J; Rossen, W R

2012-11-15

The efficiency of a foam displacement process in enhanced oil recovery (EOR) depends largely on the stability of foam films in the presence of oil. Experimental studies have demonstrated the detrimental impact of oil on foam stability. This paper reviews the mechanisms and theories (disjoining pressure, coalescence and drainage, entering and spreading of oil, oil emulsification, pinch-off, etc.) suggested in the literature to explain the impact of oil on foam stability in the bulk and porous media. Moreover, we describe the existing approaches to foam modeling in porous media and the ways these models describe the oil effect on foam propagation in porous media. Further, we present various ideas on an improvement of foam stability and longevity in the presence of oil. The outstanding questions regarding foam-oil interactions and modeling of these interactions are pointed out. Copyright © 2012 Elsevier B.V. All rights reserved.

Effect of lithological composition of oil reservoirs on oil production by a hot agent

Energy Technology Data Exchange (ETDEWEB)

Abbasov, A A; Kasimov, Sh A

1965-01-01

Several small-scale experiments were performed to determine the effect of steam on oil recovery and on permeability of water-sensitive clay-containing cores. Steam has 2 contradictory actions on oil recovery - (1) steam increases temperature and decreases viscosity of the oil, which aids oil recovery; and (2) steam hydrates and swells clays, which reduces permeability and hinders oil recovery. The oil-recovery experiments were carried out with consolidated cores containing 0, 10, and 22% clay, saturated with water and 28 cp crude oil; superheated steam at 125-300$C was used. The following conclusions were made from the experimental results: (1) oil recovery decreased as clay content of cores increased; however, at all temperatures steam recovered more oil than cold water did. (2) As steam temperature increases, oil recovery reaches a maximum, then decreases. The temperature at which oil recovery begins to decrease depends on core clay content; the higher the clay content, the lower this temperature. (3) Irrespective of whether a reservoir contains clay or not, oil recovery is considerably greater with steam than with water.

Petroleum contamination impact on macrobenthic communities under the influence of an oil refinery: Integrating chemical and biological multivariate data

Science.gov (United States)

Venturini, Natalia; Muniz, Pablo; Bícego, Márcia C.; Martins, César C.; Tommasi, Luiz Roberto

2008-07-01

Petroleum contamination impact on macrobenthic communities in the northeast portion of Todos os Santos Bay was assessed combining in multivariate analyses, chemical parameters such as aliphatic and polycyclic aromatic hydrocarbon indices and concentration ratios with benthic ecological parameters. Sediment samples were taken in August 2000 with a 0.05 m 2 van Veen grab at 28 sampling locations. The predominance of n-alkanes with more than 24 carbons, together with CPI values close to one, and the fact that most of the stations showed UCM/resolved aliphatic hydrocarbons ratios (UCM:R) higher than two, indicated a high degree of anthropogenic contribution, the presence of terrestrial plant detritus, petroleum products and evidence of chronic oil pollution. The indices used to determine the origin of PAH indicated the occurrence of a petrogenic contribution. A pyrolytic contribution constituted mainly by fossil fuel combustion derived PAH was also observed. The results of the stepwise multiple regression analysis performed with chemical data and benthic ecological descriptors demonstrated that not only total PAH concentrations but also specific concentration ratios or indices such as ≥C24:petroleum related variables seemed to have a main influence on macrofauna community structure. The PCA ordination performed with the chemical data resulted in the formation of three groups of stations. The decrease in macrofauna density, number of species and diversity from groups III to I seemed to be related to the occurrence of high aliphatic hydrocarbon and PAH concentrations associated with fine sediments. Our results showed that macrobenthic communities in the northeast portion of Todos os Santos Bay are subjected to the impact of chronic oil pollution as was reflected by the reduction in the number of species and diversity. These results emphasise the importance to combine in multivariate approaches not only total hydrocarbon concentrations but also indices, isomer pair

Rapeseed oil, olive oil, plant sterols, and cholesterol metabolism: an ileostomy study.

Science.gov (United States)

Ellegård, L; Andersson, H; Bosaeus, I

2005-12-01

To study whether olive oil and rapeseed oil have different effects on cholesterol metabolism. Short-term experimental study, with controlled diets. Outpatients at a metabolic-ward kitchen. A total of nine volunteers with conventional ileostomies. Two 3-day diet periods; controlled diet including 75 g of rapeseed oil or olive oil. Cholesterol absorption, ileal excretion of cholesterol, and bile acids. Serum levels of cholesterol and bile acid metabolites. Differences between diets evaluated with Wilcoxon's signed rank sum test. Rapeseed oil diet contained 326 mg more plant sterols than the olive oil diet. Rapeseed oil tended to decrease cholesterol absorption by 11% (P = 0.050), and increased excretion of cholesterol, bile acids, and their sum as sterols by 9% (P = 0.021), 32% (P = 0.038), and 51% (P = 0.011) compared to olive oil. A serum marker for bile acid synthesis (7alpha-hydroxy-4-cholesten-3-one) increased by 28% (P = 0.038) within 10 h of consumption, and serum cholesterol levels decreased by 7% (P = 0.024), whereas a serum marker for cholesterol synthesis (lathosterol) as well as serum levels of plant sterols remained unchanged. Rapeseed oil and olive oil have different effects on cholesterol metabolism. Rapeseed oil, tends to decrease cholesterol absorption, increases excretion of cholesterol and bile acids, increases serum marker of bile acid synthesis, and decreases serum levels of cholesterol compared to olive oil. This could in part be explained by different concentrations of natural plant sterols. Supported by the Göteborg Medical Society, the Swedish Medical Society, the Swedish Board for Agricultural Research (SJFR) grant 50.0444/98 and by University of Göteborg.

Liquid oil and residual characteristics of printed circuit board recycle by pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Lin, Kuo-Hsiung [Department of Environmental Engineering and Science, Fooyin University, Kaohsiung, Taiwan (China); Chiang, Hung-Lung, E-mail: hlchiang@mail.cmu.edu.tw [Department of Health Risk Management, China Medical University, Taichung, Taiwan (China)

2014-04-01

Highlights: • Pyrolysis is a technology for recycling of the non-metal fraction of PCBs. • Liquid product constituents were analyzed for PCB pyrolysis. • Water-soluble ionic species were determined for PCB pyrolysis exhaust. - Abstract: Non-metal fractions of waste printed circuit boards (PCBs) were thermally treated (200–500 °C) under nitrogen atmosphere. Carbon, hydrogen, and nitrogen were determined by elemental analyzer, bromine by instrumental neutron activation analysis (INAA), phosphorus by energy dispersive X-ray spectrometer (EDX), and 29 trace elements by inductively coupled plasma atomic emission spectrometer (ICP-AES) and mass spectrometry (ICP-MS) for raw material and pyrolysis residues. Organic compositions of liquid oil were identified by GC (gas chromatography)–MS, trace element composition by ICP system, and 12 water-soluble ions by IC (ionic chromatography). Elemental content of carbon was >450 mg/g, oxygen 300 mg/g, bromine and hydrogen 60 mg/g, nitrogen 30 mg/g, and phosphorus 28 mg/g. Sulfur was trace in PCBs. Copper content was 25–28 mg/g, iron 1.3–1.7 mg/g, tin 0.8–1.0 mg/g and magnesium 0.4–1.0 mg/g; those were the main metals in the raw materials and pyrolytic residues. In the liquid products, carbon content was 68–73%, hydrogen was 10–14%, nitrogen was 4–5%, and sulfur was less than 0.05% at pyrolysis temperatures from 300 to 500 °C. Phenol, 3-bromophenol, 2-methylphenol and 4-propan-2-ylphenol were major species in liquid products, accounting for >50% of analyzed organic species. Bromides, ammonium and phosphate were the main species in water sorption samples for PCB pyrolysis exhaust.

X-ray photoelectron spectroscopic and morphologic studies of Ru nanoparticles deposited onto highly oriented pyrolytic graphite

Science.gov (United States)

Bavand, R.; Yelon, A.; Sacher, E.

2015-11-01

Ruthenium nanoparticles (Ru NPs) function as effective catalysts in specific reactions, such as methanation and Fischer-Tropsch syntheses. It is our purpose to physicochemically characterize their surfaces, at which catalysis occurs, by surface-sensitive X-ray photoelectron spectroscopy (XPS), using the symmetric peak component anaylsis technique developed in our laboratory to reveal previously hidden components. Ru NPs were deposited by evaporation (0.25-1.5 nm nominal deposition range) onto highly oriented pyrolytic graphite (HOPG). In addition to their surfaces being characterized by XPS, an indication of morphology was obtained from transmission electron microscopy (TEM). Our use of symmetric peak component XPS analysis has revealed detailed information on a previously unidentified surface oxide initially formed, as well as on the valence electronic structure and its variation with NP size, information that is of potential importance in the use of these NPs in catalysis. Each of the several Ru core XPS spectra characterized (3d, 3p and 3s) was found to be composed of three symmetric components. Together with two metal oxide O1s components, these give evidence of a rather complex, previously unidentified oxide that is initially formed. The Ru valence band (4d and 5s) spectra clearly demonstrate a loss of metallicity, a simultaneous increase of the Kubo gap, and an abrupt transfer in valence electron density from the 4d to the 5s orbitals (known as electron spill-over), as the NP size decreases below 0.5 nm. TEM photomicrographs, as a function of deposition rate, show that, at a rate that gives insufficient time for the NP condensation energy to dissipate, the initially well-separated NPs are capable of diffusing laterally and aggregating. This indicates weak NP bonding to the HOPG substrate. Carbide is formed, at both high and low deposition rates, at Ru deposition thicknesses greater than 0.25 nm, its formation explained by Ru NPs reacting with residual

Development of new antioxidant systems for frying oil and omega-3 oils

Science.gov (United States)

The development of natural antioxidant systems for frying oil will be discussed in this presentation. This study aimed to utilize vegetable oils such as soybean oil for frying, of which the United States is the world’s largest producer. To overcome the vulnerability of soybean oil to oxidation due t...

OIL AS POLITICAL WEAPON

Directory of Open Access Journals (Sweden)

Mariana, BUICAN

2013-12-01

Full Text Available Oil (called by some black gold has not always been as coveted and used, but only in the last hundred years has established itself as a highly sought after as an indispensable proper functioning of modern economic activity that an important factor in international politics. International oil regime has changed in the last decades. In 1960, oil regime was a private oligopol which had links with governments main consuming countries. By then the price of a barrel of oil was two U.S. dollars and seven major transnational oil companies decided the amount of oil that will be produced. Meanwhile the world region with the largest oil exports were more strongly expressed nationalism and decolonization. Result, it was so in the late 60s in the region occur independent states. They have created an organization aim of this resource to their advantage - OPEC (Organization of Petroleum Exporting Countries. Thus since 1973 there have been changes in the international regime governing oil field, namely producing countries were fixed production rate and price. After this time the oil weapon has become increasingly important in the management of international relations. Oil influenced the great powers to Middle East conflicts that occurred in the last century, but their attitude about the emergence of new sources of oil outside OPEC. In the late 90's, Russia has become a major supplier of oil to the West.

Microbial ecology of methanogenic crude oil biodegradation; from microbial consortia to heavy oil

Energy Technology Data Exchange (ETDEWEB)

Head, Ian M.; Maguire, Michael J.; Sherry, Angela; Grant, Russell; Gray, Neil D.; Aitken, Carolyn M.; Martin Jones, D.; Oldenburg, Thomas B.P.; Larter, Stephen R. [Petroleum Research Group, Geosciences, University of Calgary (Canada)

2011-07-01

This paper presents the microbial ecology of methanogenic crude oil biodegradation. Biodegraded petroleum reservoirs are one of the most dramatic indications of the deep biosphere. It is estimated that heavy oil and oil sands will account for a considerable amount of energy production in the future. Carbon, a major resource for deep subsurface microorganisms, and energy are contained in large quantities in petroleum reservoirs. The aerobic to anaerobic paradigm shift is explained. A key process for in-situ oil biodegradation in petroleum reservoirs is methanogenesis. New paradigms for in-reservoir crude oil biodegradation are discussed. Variations in anaerobic degradation of crude oil hydrocarbons are also discussed. A graph shows the different patterns of crude oil biodegradation under sulfate-reducing and methanogenic conditions. Alternative anaerobic alkane activation mechanisms are also shown. From the study, it can be concluded that methanogenic crude oil degradation is of global importance and led to the establishment of the world's enormous heavy oil deposits.

Economic Exposure to Oil Price Shocks and the Fragility of Oil-Exporting Countries

Directory of Open Access Journals (Sweden)

Toon Vandyck

2018-04-01

Full Text Available From a price range between 100 and 120 USD (U.S. dollars per barrel in 2011–2014, the crude oil price fell from mid-2014 onwards, reaching a level of 26 USD per barrel in January 2016. Here we assess the economic consequences of this strong decrease in the oil price. A retrospective analysis based on data of the past 25 years sheds light on the vulnerability of oil-producing regions to the oil price volatility. Gross domestic product (GDP and government revenues in many Gulf countries exhibit a strong dependence on oil, while more diversified economies improve resilience to oil price shocks. The lack of a sovereign wealth fund, in combination with limited oil reserves, makes parts of Sub-Saharan Africa particularly vulnerable to sustained periods of low oil prices. Next, we estimate the macroeconomic impacts of a 60% oil price drop for all regions in the world. A numerical simulation yields a global GDP increase of roughly 1% and illustrates how the regional impact on GDP relates to oil export dependence. Finally, we reflect on the broader implications (such as migration flows of macroeconomic responses to oil prices and look ahead to the challenge of structural change in a world committed to limiting global warming.

Solidifier effectiveness : variation due to oil composition, oil thickness and temperature

International Nuclear Information System (INIS)

Fieldhouse, B.; Fingas, M.

2009-01-01

This paper provided an overview of solidifier types and composition. Solidifiers are a class of spill treating agents that offer an effective means to convert a liquid oil into a solid material. They are used as a treatment option for oil spills on water. This paper also reported on recent laboratory studies that consist of 4 components: (1) a qualitative examination of the characteristics of the interaction of a broad range of solidifier products with a standard oil to evaluate reaction rate, states of solidification, and the impact of dosage, (2) a comparison of a smaller subset of solidifiers on the standard oil at lower temperatures, (3) solidifier treatment on a range of oils of varying physical properties and composition to assess the potential scope of application, and (4) the treatment of a series of small-scale oil layers of varying thickness to determine the significance of oil thickness on solidifier effectiveness and recovery. This paper also reviewed solidifier chemistry with particular reference to polymer sorbents; cross-linking agents; and cross-linking agents and polymeric sorbents combined. Toxicity is also an important issue regarding solidifiers. The aquatic toxicity of solidifiers is low and not measurable as the products are not water-soluble. There have not been any studies on the effects of the solidifier or the treated oil on surface feeders and shoreline wildlife that may come into contact with the products. It was concluded that oil composition may play a major role in solidifier effectiveness. The effectiveness of solidifiers is also inhibited at reduced temperatures, increased viscosity and density of the oil. 25 refs., 5 tabs., 2 figs., 1 appendix

Effect of citronella essential oil fractions as oil phase on emulsion stability

Science.gov (United States)

Septiyanti, Melati; Meliana, Yenny; Agustian, Egi

2017-11-01

The emulsion system consists of water, oil and surfactant. In order to create stable emulsion system, the composition and formulation between water phase, surfactant and oil phase are very important. Essential oil such as citronella oil has been known as active ingredient which has ability as insect repellent. This research studied the effect of citronella oil and its fraction as oil phase on emulsion stability. The cycle stability test was conducted to check the emulsion stability and it was monitored by pH, density, viscosity, particle size, refractive index, zeta potential, physical appearance and FTIR for 4 weeks. Citronellal fraction has better stability compared to citronella oil and rhodinol fraction with slight change of physical and chemical properties before and after the cycle stability test. However, it is need further study to enhance the stability of the emulsion stability for this formulation.

Application of synthetic fire-resistant oils in oil systems of turbine equipment for NPPs

Science.gov (United States)

Galimova, L. A.

2017-10-01

Results of the investigation of the synthetic fire-resistant turbine oil Fyrquel-L state in oil systems of turbosets under their operation in the equipment and oil supply facilities of nuclear power plants (NPPs) are presented. On the basis of the analysis of the operating experience, it is established that, for reliable and safe operation of the turbine equipment, at which oil systems synthetic fire-resistant oils on the phosphoric acid esters basis are used, special attention should be paid to two main factors, namely, both the guarantee of the normalized oil water content under the operation and storage and temperature regime of the operation. Methods of the acid number maintenance and reduction are shown. Results of the analysis and investigation of influence of temperature and of the variation of the qualitative state of the synthetic fair-resistant oil on its water content are reported. It is shown that the fire-resistant turbine oils are characterized by high hydrophilicity, and, in distinction to the mineral turbine oils, are capable to contain a significant amount of dissolved water, which is not extracted under the use of separation technologies. It is shown that the more degradation products are contained in oil and higher acid number, the more amount of dissolved water it is capable to retain. It is demonstrated that the organization of chemical control of the total water content of fireresistant oils with the use of the coulometric method is an important element to support the reliable operation of oil systems. It is recommended to use automatic controls of water content for organization of daily monitoring of oil state in the oil system. Recommendations and measures for improvement of oil operation on the NPP, the water content control, the use of oil cleaning plants, and the oil transfer for storage during repair works are developed.

21 CFR 102.37 - Mixtures of edible fat or oil and olive oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Mixtures of edible fat or oil and olive oil. 102... for Specific Nonstandardized Foods § 102.37 Mixtures of edible fat or oil and olive oil. The common or usual name of a mixture of edible fats and oils containing less than 100 percent and more than 0 percent...

Exploration of process parameters for continuous hydrolysis of canola oil, camelina oil and algal oil

KAUST Repository

Wang, Weicheng

2012-07-01

Thermal hydrolysis of triglycerides to form free fatty acid (FFA) is a well-established industry practice. Recently, this process has been employed as a first step in the production of biofuels from lipids. To that end, batch and continuous hydrolysis of various feedstocks has been examined at the laboratory scale. Canola, the primary feedstock in this paper, camelina and algal oils were converted to high quality FFA. For the different reaction temperatures, the continuous hydrolysis system was found to provide better yields than the laboratory batch system. In addition, CFD simulation with ANSYS-CFX was used to model the performance and reactant/product separation in the continuous, counter-flow reactor. The effects of reaction temperature, water-to-oil ratio (ratio of water and oil volumetric inflow rate), and preheating of the reactants were examined experimentally. Optimization of these parameters has resulted in an improved, continuous process with high mass yields (89-93%, for reactor temperature of 260°C and water-to-oil ratio of 4:1) and energy efficiency (76%, for reactor temperature of 250°C and water-to-oil ratio of 2:1). Based on the product quality and energy efficiency considerations, the reactor temperature of 260°C and water-to-oil ratio of 4:1 have provided the optimal condition for the lab scale continuous hydrolysis reaction. © 2012 Elsevier B.V.

Exploration of process parameters for continuous hydrolysis of canola oil, camelina oil and algal oil

KAUST Repository

Wang, Weicheng; Turner, Timothy L.; Stikeleather, Larry F.; Roberts, William L.

2012-01-01

Thermal hydrolysis of triglycerides to form free fatty acid (FFA) is a well-established industry practice. Recently, this process has been employed as a first step in the production of biofuels from lipids. To that end, batch and continuous hydrolysis of various feedstocks has been examined at the laboratory scale. Canola, the primary feedstock in this paper, camelina and algal oils were converted to high quality FFA. For the different reaction temperatures, the continuous hydrolysis system was found to provide better yields than the laboratory batch system. In addition, CFD simulation with ANSYS-CFX was used to model the performance and reactant/product separation in the continuous, counter-flow reactor. The effects of reaction temperature, water-to-oil ratio (ratio of water and oil volumetric inflow rate), and preheating of the reactants were examined experimentally. Optimization of these parameters has resulted in an improved, continuous process with high mass yields (89-93%, for reactor temperature of 260°C and water-to-oil ratio of 4:1) and energy efficiency (76%, for reactor temperature of 250°C and water-to-oil ratio of 2:1). Based on the product quality and energy efficiency considerations, the reactor temperature of 260°C and water-to-oil ratio of 4:1 have provided the optimal condition for the lab scale continuous hydrolysis reaction. © 2012 Elsevier B.V.

A scanning tunneling microscope study on an ordered mixed monolayer of bis(4,5-dihydronaphtho[1,2-d])-tetrathiafulvalene and n-tetradecane on highly oriented pyrolytic graphite.

Science.gov (United States)

Zhao, Miao; Jiang, Peng; Deng, Ke; Jiang, Chao

2010-11-01

Tetrathiafulvalene (TTF) and its derivatives (TTFs) have been successfully used as building blocks to form charge transfer salts and organic semiconductors because of their special structures and rich electron nature. We report the formation of ordered mixed binary-component monolayer consisting of Bis(4,5-dihydronaphtho[1,2-d])tetrathiafulvalene (DH-TTF) and n-tetradecane (n-C14H30) molecules on highly oriented pyrolytic graphite (HOPG) surface. Scanning tunneling microscope (STM) imaging reveals that the two different kinds of molecules can spontaneously form ordered periodic phase separation structures on the substrate, in which ordered DH-TTF double- (or single-) lamella structures are periodically tuned by ordered n-C14H30 double- (or single-) lamella structures. Furthermore, scanning tunneling spectrum (STS) measurements by addressing the individual DH-TTF and n-C14H30 molecules in the ordered monolayer show that the two different kinds of molecules exhibit completely different I(V) characters on the HOPG substrate. The modulated arrangement of the TTF derivative by insulating molecules opens a possible route to construct organic conducting molecule ribbons for potential application in nanodevices.

Cod Liver Oil

Science.gov (United States)

Cod liver oil can be obtained from eating fresh cod liver or by taking supplements. Cod liver oil is used as a source of vitamin A ... called macular degeneration. Some people put cod liver oil on their skin to speed healing of wounds, ...

When oil spills emulsify

International Nuclear Information System (INIS)

Bobra, M.; Fingas, M.; Tennyson, E.

1992-01-01

Cleanup operations of oil spills must take into account the numerous detrimental effects attributable to the emulsification of spilled oil into a stable water-in-oil mousse. The incorporation of water greatly increases the volume of the polluted material. The viscous nature of mousse impedes the efficient operation of most mechanical recovery equipment and results in a cohesive slick that resists dispersion, both natural and artificial. The rate at which spilled oil emulsifies determines the effective window of opportunity for specific countermeasures. Much has been learned from previous studies on petroleum emulsification, but is still remain a poorly understood phenomenon. Although most crude oils can be emulsified, not all spills result in the formation of stable mousse. The formation of mousse results from a complex series of processes. Whether an oil will form mousse or not, and if so, at what rate, depends on an array of different factors including the properties of the oil and the prevailing environmental conditions. We need a greater understanding of the emulsification process to better predict the emulsification behavior of oil spills and utilize the most appropriate countermeasures available. In this paper, the authors report on work to elucidate the role that physicochemical factors play in determining an oil's tendency to emulsify. The authors studied the emulsification behavior of oils of known composition to examine the importance of oil chemistry in the emulsification process

What about oil reserve depletion and crude oil price evolution?

International Nuclear Information System (INIS)

2007-01-01

The objective of this report is to give a synthesis of different points of view with respect to the 'Peak Oil' perspective and to the crude oil price evolution. In the first part, the authors examine the evolutions and assessments of oil reserves and productions, by discussing the different types of reserve, the optimistic and pessimistic points of views. Then, in the second part, they analyse the long term price formation, the various production technical costs (conventional oils, heavy oils and asphaltic sands, coal- and gas-based synthetic hydrocarbons, bio-fuels), the external costs (notably in relationship with greenhouse emissions), the relationship between geopolitical issues and short and middle term price formation. In the third and last part, they discuss the possible evolutions and scenarios in terms of demand, production, and prices

The Asia-Pacific oil market : prospects for Canadian oil

International Nuclear Information System (INIS)

Fesharaki, F.

2004-01-01

The Asia-Pacific region is among the fastest growing oil markets for which analysts predict healthy growth rates due to high energy demands from developing countries such as China. Increased oil demand will mean new refining capacity needs and increased supplies of crude oil. The indigenous crude supply in the Asia-Pacific region is limited and unable to meet the region's needs. Imports are therefore expected to rise continuously. Although the Middle East will continue to be the dominant player in meeting these growing oil needs, Canada has an opportunity to diversify the supply source and play a significant role in meeting the energy needs of the Asia-Pacific region. tabs., figs

Ozonated Olive Oils and Troubles

Directory of Open Access Journals (Sweden)

Bulent Uysal

2014-04-01

Full Text Available One of the commonly used methods for ozone therapy is ozonated oils. Most prominent type of used oils is extra virgin olive oil. But still, each type of unsaturated oils may be used for ozonation. There are a lot of wrong knowledge on the internet about ozonated oils and its use as well. Just like other ozone therapy studies, also the studies about ozone oils are inadequate to avoid incorrect knowledge. Current data about ozone oil and its benefits are produced by supplier who oversees financial interests and make misinformation. Despite the rapidly increasing ozone oil sales through the internet, its quality and efficacy is still controversial. Dozens of companies and web sites may be easily found to buy ozonated oil. But, very few of these products are reliable, and contain sufficiently ozonated oil. This article aimed to introduce the troubles about ozonated oils and so to inform ozonated oil users. [J Intercult Ethnopharmacol 2014; 3(2.000: 49-50

The third oil shock: The effects of lower oil prices

Energy Technology Data Exchange (ETDEWEB)

Pearce, J

1983-01-01

This book assesses how oil prices have affected other elements of the economy and assesses the costs and benefits that could result from lower oil prices for different groups of countries. The book also analyses the extent of OPEC's influence, the consumers countries' needs for energy security and the altered role of the oil industry.

The North Cape oil spill assessment: PAHs in oil

International Nuclear Information System (INIS)

Brown, J.; Boehm, P. D.; Hardestine, J. H.; Douglas, G. S.

1997-01-01

The North Cape oil spill in January 1996 resulted in the release of an estimated 827,000 gallons of No. 2 home heating oil into the nearshore turbulent waters of coastal Rhode Island. The oil was mixed into the water column and was transported on the surface as well as below the surface. Some of the spilled oil entered the coastal ponds behind the beaches. Sampling and chemical analysis for detailed suites of petroleum saturated and polycyclic aromatic hydrocarbons (PAHs) was undertaken as part of the assessment of the fate of the oil spill and of the exposure to the marine environment. The ponds were found to contain significant quantities of background petroleum hydrocarbons, including petrogenic PAHs and combustion PAHs. Initial assessment pointed (incorrectly as it turned out) to widespread contamination due only to the North Cape spill. Application of advanced chemical fingerprinting approaches, and geochemical biomarker data illustrated that many of the PAHs consisted of combustion-related 4- and 5-ringed PAHs, attributable to diesel fuel used routinely by boats in the area. The analysis demonstrated that the use of non-specific total PAH data and insufficient fingerprinting and allocation of petrogenic residues has the potential to overestimate contamination and hence injury to the environment in similar oil spill situations

Determination of Calorific Ability of Fuel Briquettes on the Basis of Oil and Oil Slimes

Science.gov (United States)

Fedyaeva, O. A.; Poshelyuzhnaya, E. G.; Rakhmatulina, E. M.; Zakharov, V. A.; Fisenko, T. E.

2018-01-01

Utilization and neutralization of oil slimes is one of important environmental problems of the oil-extracting, oil-processing and petrochemical industry. The easiest and economic way of utilization of oil slimes is their use as a part of the bricketed boiler fuel. In this work the highest calorific ability of crude oil, the oil slimes and fuel briquettes made on their basis is defined. A research problem was carrying out the technical analysis of oil fuels on the content in them analytical moisture, the cindery rest and volatiles. It is established that in comparison with oil slimes crude oil possesses bigger highest calorific ability, has smaller humidity and an ash-content. The highest calorific abilities of the boiler briquettes made of samples of crude oil, oil slimes and peat made 14 - 26 MJ/kg.

Preliminary use of cashew kernel oil in Clarias gariepinus fingerlings diet: comparison with fish oil and palm oil

Directory of Open Access Journals (Sweden)

Morgane Paul Magouana Anvo

2017-04-01

Full Text Available Abstract The present study was performed to investigate the effect of fish oil (FO, palm oil (PO, and cashew kernel oil (CKO as the dietary lipid sources on the growth performance, tissues fatty acids composition and economical profitability in Clarias gariepinus fingerlings. Three isonitrogenous (49.32%, isolipidic (15.18%, and isoenergetic (21 kJ/g diets were formulated, differed only to the added lipid source and coded accordingly as D1 (fish oil, D2 (palm oil, and D3 (cashew kernel oil. Catfish fingerlings (initial body weight = 2.43 ± 0.04 g were stocked at 1 fish/L and fed to trial diets at 5.6%. At the end of 8 weeks, C. gariepinus fingerlings fed with D1 and D3 had significantly identical growth and feed utilization efficiency. Those fed with D2 exhibited significantly and numerically low growth performance compared, respectively, to D1 and D3. Contrary to whole-body composition of fish, the muscle lipids fatty acids composition was influenced by the fatty acids profile of the dietary lipid sources. High net profit value (NPV of 24.59$, high investment cost analysis (ICA of 10.14$ and low benefit: cost ratio (BCR of 2.42 were observed in fish fed with D1 while those fed with D3 allowed to have high NPV (23.15$, low ICA (7.86$ and high BCR (2.95. Like others vegetable oils, cashew kernel oil can replace expensive fish oil in C. gariepinus fingerlings diet without negatively affecting its growth performances.

Mineral oil

International Nuclear Information System (INIS)

Schult-Bornemann, Karl-Heinz

2015-01-01

The dominant theme in the world energy market was the fall in oil prices in 2014. From 115 US-$/bbl in June it dropped to below 50 US-$/bbl in January 2015. Thereby the shale oil revolution has had the strong impact on the global energy situation, to this point has been predicted for three years. Although no one could predict the exact height of the fall in oil prices, but with oil as a reserve currency for all other fuels, it has not only had an impact on the gas and coal prices, but other commodities, such as copper, have also yielded. About cause and effect, there is a lot of speculation - not all of which are supported by wisdom. [de

Sassafras oil overdose

Science.gov (United States)

Sassafras oil comes from the root bark of the sassafras tree. Sassafras oil overdose occurs when someone swallows more than the ... Safrole is the poisonous ingredient in sassafras oil. It is a clear or ... yellow oily liquid. It can be dangerous in large amounts.

Oil spill risk assessment : relative impact indices by oil type and location

International Nuclear Information System (INIS)

French-McCay, D.; Beegle-Krause, C.J.; Rowe, J.; Rodriguez, W.; Schmidt Etkin, D.

2009-01-01

The aim of the study was to inform policies related to resource allocation for oil spill prevention, preparedness and response activities in Washington State. Oil spill reports and impact modelling studies were evaluated in order to determine major risk consequence factors including spill volume, location, timing, toxicity, persistence, and expected frequency of spills by sector. The Washington Compensation Schedule pre-assessment screening and oil spill compensation schedule regulations (WCS) designed to consider the sensitivity of oiled areas as well as the relative density and seasonal distributions of sensitive biota. Spill incidents were assigned per-gallon impact scores based on geographic location, oil type, and season. The WCS qualitative rating system was used to assess the potential impacts of spills in different geographic systems. Geographic zones were based on geography, circulation of currents, climate, and the WCS sub-regions in estuarine and marine areas on the Pacific coast of Washington State. Oil types included crude, heavy, and light oils; gasoline; jet fuel; and non-petroleum oils. A habitat index was calculated to represent existing stream conditions. It was concluded that the relative impact risk model is a reliable method for characterizing impacts based on spill volume, oil effects, and vulnerability rankings. 25 refs., 20 tabs., 3 figs

Oil slick skimmer

International Nuclear Information System (INIS)

Karterman, D.S.

1993-01-01

A craft for removing an oil slick from a body of water is described comprising: a pair of spacedly arranged paralleled positioned elongated floats, a platform mounted on and extending between said floats, a weir mounted on said platform between said floats and being movable independently and substantially vertical of the longitudinal axis of said floats to a position below the surface of said body of water, a submersible oil receiving and storage means detachedly mounted to said platform between said floats and having an inlet port at one level and comprising a substantially enclosed oil accumulator having an outlet port at a lower level, said weir comprising a sluice gate constructed and arranged to admit into said inlet port of said oil receiving and storage means under the effects of gravity a portion of an oil stick comprising a water and oil mixture skimmed from said body of water, and a first pump connected to said outlet port of said accumulator to control the movement of water from the inside lower level of said accumulator out of said accumulator to thereby control the amount of the oil slick flowing into said accumulator

BIODIESEL FUELS FROM PALM OIL, PALM OIL METHYLESTER ...

African Journals Online (AJOL)

a

determined by methods outlined by A.O.C.S. (American Oil Chemist Society) [12], Usoro et al. [15], Clark [2], and ... diesel have shown that novel vegetable diesels could be obtained from palm oil. .... C-H stretch for alkenes and aromatics.

Purification of water polluted with oil and sulfurous closed-ring and aromatic compounds contained in oil and oil products using bacteria relating to thiosphaera

International Nuclear Information System (INIS)

Kurashov, V.M.; Sakhno, T.V.; Gavrilov, V.S.; Zijatdinov, R.N.

2005-01-01

The intensity of natural purification (self-purification) of reservoirs polluted with oil and oil products is determined by microorganisms. Hydrocarbon-oxidizing microorganisms are constant natural constituent of biocenose in reservoirs. However, as a result of outflows, the oil and oil products concentration exceeds maximum values allowing normal vital functions of microorganisms resulting in breaking micro-biocenose suppression of vital functions of bacteria. In this regard, elective anaerobic microorganisms of Thiosphaera are worthy of notice. We found out that bacteria belonging to Thiosphaera pantotropha decomposed oil at high oil concentrations in water (at oil concentration like 1 liter of oil in 1 liter of water). And this is when aerobic microorganisms lose their vital functions at maximum concentration of 20 g of oil in 1 liter of water. To intensify the process of oil decomposition we emulsified oil with aqueous solutions of salts. Thiosphaera pantotropha are found out to decompose oil in a wide range of ratio between oil and aqueous solutions of salts: from 1:10 to 10:1. The water solutions salinity made from 20 g/l to 80 g/l. It must be noticed that, since the Thiosphaera pantotropha are elective anaerobes and decompose oil both in presence and in absence of oxygen, it is not necessary anymore to conduct the process under strictly anaerobic conditions and to supply additional oxygen. This makes it possible to simplify the process of biodegradation of oil and to make this process practically more feasible and economically more profitable being compared to the processes based on the use of other species of bacteria. We found out that Thiosphaera decompose sulfurous closed-ring and aromatic compounds in oil which are chemically and thermally stable and can be hardly decomposed, and possess extremely poisonous properties, as well. The use of microorganisms of Thiosphaera pantotropha allows to purify waters polluted with oil and oil products both during

Contained controlled burning of spilled oil during the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Allen, A.A.

1990-01-01

During the evening of the second day following the Exxon Valdez oil spill, an estimated 57,000-114,000 liters of North Slope crude oil were eliminated using in-situ combustion. The oil was collected with 3M's Fire Boom towed in a U-shaped configuration behind two fishing boats. Working with 152 m long tow lines, a 137 m boom was moved at ca 0.26-5.2 m/s through slightly emulsified oil patches in the downwind region of the spill. A gelled fuel ignitor was used to ignite the captured oil, and the size and intensity of the blaze was controlled by adjusting the speed of the vessels. Total burn time was ca 1.25 h, however the intense part of the burn lasted for ca 45 minutes. Using several methods to estimate the total volume of oil collected, the volume resulted in ca 1136 liters of stiff, taffy-like burn residue that could be picked up easily on completion of the burn. The controlled burn thus resulted in an estimated 98% or better elimination of crude oil. It had been planned to use a helitorch to ignite the captured oil, however darkness required the use of the gelled ignitor. Had the helitorch been used, numerous ignition points could have been spread througout the contained oil, providing a much more efficient heating and ultimate ignition of the oil. 5 figs

ECONOMIC CONSEQUENCES OF PEAK OIL FOR THE MAJOR MULTINATIONAL OIL AND GAS COMPANIES

Directory of Open Access Journals (Sweden)

Antonio García-Amate

2018-03-01

Full Text Available The main goal of this work is to analyze the financial statements of the five major multinational oil and gas companies, for the 2011-2015 period, in the framework of the peak oil phenomenon. Peak oil can affect key financial indicators (e.g., earnings volatility, leverage that are used by managers, investors, and stockholders and which may potentially lead to changes in the decision making by management. Our results show that the decline in oil production affects the decisions about investment in new oil wells, leverage, dividends paid, shares purchased and net income involving the five major companies. In addition, we study the evolution of oil prices, and its influence in several items of the financial statements. Even though oil prices were at high levels during 2011-2014, however, the net income of the five companies actually declined due to the impact of peak oil. Finally, data for the last year studied (2015 indicate a general deterioration in return ratios and other accounting variables. Although the new investments should have been profitable, they have been influenced by peak oil, compromising the economic position of the companies. The advice to these companies would be to relax their investments, especially during a period of falling oil prices. Company managers need to recognize the prolonged duration of peak oil and price trends to promote profitability recovery decisions.

Oil analysis in machine diagnostics

Energy Technology Data Exchange (ETDEWEB)

Vaehaeoja, P.

2006-07-01

This study concentrates on developing and tuning various oil analysis methods to meet the requirements of modern industry and environmental analytics. Oil analysis methods form a vital part of techniques used to monitor the condition of machines and may help to improve the overall equipment effectiveness value of a factory in a significant manner. Worm gears are used in various production machines, and their breakdowns may cause significant production losses. Wearing of these gears is relatively difficult to monitor with vibration analysis. Analysis of two indicator metals, copper and iron, may reveal wearing phenomena of worm gears effectively, and savings can be significant. Effective wear metal analysis requires good tools. ICP-OES with kerosene dilution is widely used in wear metal analysis, but purchasing and using of ICP-OES is expensive. A cheaper FAAS technique with similar pre-treatment of oil samples was tested and it proved to be useful especially in analyzing small amounts of samples. The accuracy of FAAS was sufficient for quantitative work in machine diagnostics and waste oil characterization. Solid debris analyses are useful in oil contamination control as well as in detection of wearing mechanisms. Membrane filtration, optical microscopy, SEM and automatic particle counting were applied in analysis of rolling and gear oils. Particle counting is an effective way to detect oil contamination, but in the studied cases even larger particles than those detected in normal ISO classes would be informative. However, membrane filtration and optical microscopy may reveal the wearing machine element exactly. Additives provide oils with desired properties thus they should be monitored intensively. A FTIR method for quantitative analysis of fatty alcohols and fatty acid esters in machinery oils was developed during this work. It has already been used successfully in quantitative and qualitative analysis of machinery oil samples. Various kinds of oils may be

The Asymmetric Effects of Oil Shocks on an Oil-exporting Economy

OpenAIRE

Omar Mendoza; David Vera

2010-01-01

We estimate the effects of unexpected changes in oil prices on output for the case of Venezuela, an oil-exporting economy. Following Hamilton (2003), Lee et al. (1995), and Mork (1989), we estimate measures of oil shocks and determine the effect of these

Manitoba oil activity review, 1992

International Nuclear Information System (INIS)

1993-04-01

In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explanations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1992, 28 wells were drilled, compared to 54 in 1991. Oil production was down ca 8% from 1991 levels, to 656,415 m 3 ; the value of the oil produced decreased 4% to ca $86.3 million; and provincial revenues from the oil industry decreased by 24%. Oil industry expenditures in the province were estimated at $58 million, down 16% from 1991. As of 4 January 1993, there were 11 oil fields and 120 non-confidential oil pools designated in Manitoba. Crude oil prices fluctuated throughout the year. In 1992, Manitoba's average crude oil price was $20.89/bbl, compared with 1991's average of $20.14/bbl. Manitoba Energy and Mines amended the Drilling Incentive Program to provide a 10,000 m 3 holiday volume for horizontal wells. 12 figs., 17 tabs

Manitoba oil activity review, 1993

International Nuclear Information System (INIS)

1994-07-01

In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explanations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1993, 87 wells were drilled, compared to 28 in 1992. Oil production was down ca 3% from 1992 levels, to 634,561 m 3 ; the value of the oil produced decreased 10% to ca $77.5 million; and provincial revenues from the oil industry decreased by 4%. Oil industry expenditures in the province were estimated at $73 million, up 26% from 1992. As of 4 January 1994, there were 11 oil fields and 120 non-confidential oil pools designated in Manitoba. Crude oil prices fluctuated throughout the year, between $15.12 and $21.50/bbl. In 1993, Manitoba's average crude oil price was $19.40/bbl, compared with 1992's average of $20.89/bbl. Manitoba Energy and Mines amended the Drilling Incentive Program to provide a 10,000 m 3 holiday volume for horizontal wells. 12 figs., 17 tabs

Process for separating and recovering oil from oil-sands, etc

Energy Technology Data Exchange (ETDEWEB)

Preller, H

1920-07-14

A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil shale, and coal is characterized in that the material to be separated feeds, by a self-acting feeding arrangement, to a system with slowly rotating drums alternating in different directions and thereby it is exposed to the action of hot water running opposite to the rotation, direction of the drum, with addition of extraction-medium, so that the light material is washed out and rises to the top. It is carried off, while the heavy material sinks to the bottom and, by bucket-conveyor is removed.

Manitoba oil activity review, 1991

International Nuclear Information System (INIS)

1992-04-01

In an annual survey of Manitoba's petroleum industry, data are presented on oil and natural gas leases and sales, geophysical activity, exploration and drilling activity, production, exports to other provinces and the USA, oil prices and sales value, royalties and taxes, direct revenues from oil exploration and development, reserves, industry expenditures, and oil fields. Throughout the report, explainations are given of the items covered. Descriptions are made of new developments, the oil market, oil policies, incentive programs, and industrial activities. During 1991, 54 wells were drilled, compared to 79 in 1990. Oil production was down ca 3% from 1990 levels, to 712,792 m 3 , the value of the oil produced decreased 21% to ca $90.3 million, and provincial revenues from the oil industry declined by 15%. Oil industry expenditures in the province were estimated at $69 million, down 9% from 1990. As of the end of 1991, there were 11 oil fields and 118 non-confidential oil pools designated in Manitoba. The forecast for 1992 indicates that exploration activity will increase in response to new incentive programs. Crude oil production is expected to decline slightly to about 667,000 m 3 . 9 figs., 17 tabs

Process of transforming into light oils heavy oils from carbonization of lignites, coals, etc

Energy Technology Data Exchange (ETDEWEB)

Mony, H

1926-12-20

A process is described for transforming into light oils the heavy oils coming from the carbonization of lignites, peats, coals, and shales, and heavy oils from original minerals and vegetables, consisting of heating the heavy oils or tars in the presence of one or more solid or liquid substances conveniently chosen, with a veiw to effect distillation of the oils under atmospheric pressure at an appropriate temperature, the solids or liquid substances favoring the formation of light products under the influence of heat, being preferably added to the oil before admitting it to the retort and heating, so that the light oils are obtained from the heavy oils in a single operation.

Oil shale commercialization study

Energy Technology Data Exchange (ETDEWEB)

Warner, M.M.

1981-09-01

Ninety four possible oil shale sections in southern Idaho were located and chemically analyzed. Sixty-two of these shales show good promise of possible oil and probable gas potential. Sixty of the potential oil and gas shales represent the Succor Creek Formation of Miocene age in southwestern Idaho. Two of the shales represent Cretaceous formations in eastern Idaho, which should be further investigated to determine their realistic value and areal extent. Samples of the older Mesozonic and paleozoic sections show promise but have not been chemically analyzed and will need greater attention to determine their potential. Geothermal resources are of high potential in Idaho and are important to oil shale prospects. Geothermal conditions raise the geothermal gradient and act as maturing agents to oil shale. They also might be used in the retorting and refining processes. Oil shales at the surface, which appear to have good oil or gas potential should have much higher potential at depth where the geothermal gradient is high. Samples from deep petroleum exploration wells indicate that the succor Creek shales have undergone considerable maturation with depth of burial and should produce gas and possibly oil. Most of Idaho's shales that have been analyzed have a greater potential for gas than for oil but some oil potential is indicated. The Miocene shales of the Succor Creek Formation should be considered as gas and possibly oil source material for the future when technology has been perfectes. 11 refs.

Raman detection of extra virgin olive oil adulterated with cheaper oils

Science.gov (United States)

Farley, Carlton; Kassu, Aschalew; Mills, Jonathan; Kenney, Brianna; Ruffin, Paul; Sharma, Anup

2016-09-01

Pure extra virgin olive oil (EVOO) is mixed with cheaper edible oils and samples are kept inside clear glass containers, while a 785nm Raman system is used to take measurements as Raman probe is placed against glass container. Several types of oils at various concentrations of adulteration are used. Ratios of peak intensities are used to analyze raw data, which allows for quick, easy, and accurate analysis. While conventional Raman measurements of EVOO may take as long as 2 minutes, all measurements reported here are for integration times of 15s. It is found that adulteration of EVOO with cheaper oils is detectable at concentrations as low as 5% for all oils used in this study.

Comparative techno-economic analysis of biohydrogen production via bio-oil gasification and bio-oil reforming

International Nuclear Information System (INIS)

Zhang, Yanan; Brown, Tristan R.; Hu, Guiping; Brown, Robert C.

2013-01-01

This paper evaluates the economic feasibility of biohydrogen production via two bio-oil processing pathways: bio-oil gasification and bio-oil reforming. Both pathways employ fast pyrolysis to produce bio-oil from biomass stock. The two pathways are modeled using Aspen Plus ® for a 2000 t d −1 facility. Equipment sizing and cost calculations are based on Aspen Economic Evaluation® software. Biohydrogen production capacity at the facility is 147 t d −1 for the bio-oil gasification pathway and 160 t d −1 for the bio-oil reforming pathway. The biomass-to-fuel energy efficiencies are 47% and 84% for the bio-oil gasification and bio-oil reforming pathways, respectively. Total capital investment (TCI) is 435 million dollars for the bio-oil gasification pathway and is 333 million dollars for the bio-oil reforming pathway. Internal rates of return (IRR) are 8.4% and 18.6% for facilities employing the bio-oil gasification and bio-oil reforming pathways, respectively. Sensitivity analysis demonstrates that biohydrogen price, biohydrogen yield, fixed capital investment (FCI), bio-oil yield, and biomass cost have the greatest impacts on facility IRR. Monte-Carlo analysis shows that bio-oil reforming is more economically attractive than bio-oil gasification for biohydrogen production. -- Highlights: ► Biohydrogen production via bio-oil reforming has higher energy efficiency compared to gasification. ► Hydrogen price, fixed capital cost, and feedstock cost most strongly affect IRR. ► Lower risk investment is biohydrogen production via bio-oil reforming

Oils, paintings and chemistry

Directory of Open Access Journals (Sweden)

Maria Eduarda Machado de Araújo

2005-01-01

Full Text Available In oil paintings artists use oils to apply pigments. These oils firstly are liquid and then solidify in a thin film. Many chemical reactions are involved in drying and also in the aging of these oils. Drying is a continuous process that begins with the oxidation of insaturated fatty acids from triglycerides to originate peroxides. These compounds suffer a cascade of reactions that lead to cross linking bonds between fatty acids residues, transforming the oil in a solid film. Identification of the film oil is possible using the palmitic/stearic ratio (P/S by chromatographic (GC and/or spectroscopic techniques. Sterol composition, phytosterols or cholesterol, determined by GC-MS or FTIR techniques, allows investigators to distinguish between oil painting and a temper one that used egg as the binding medium.

Oil shale activities in China

International Nuclear Information System (INIS)

Peng, D.; Jialin, Q.

1991-01-01

China has abundant oil shale resources, of the Early Silurian to Neogene age, the most important being the Tertiary period. The proved oil shale reserves in Fushun amount to 3.6 billion t, in Maoming 4.1 billion t. In Fushun, oil shale is produced by open-pit mining as a byproduct of coal, in Maoming it is also mined in open pits, but without coal. In China, scale oil has been produced from oil shale for 60 years. Annual production of crude shale oil amounts to about 200 000 t. The production costs of shale oil are lower than the price of crude petroleum on the world market. China has accumulated the experience and technologies of oil shale retorting. The Fushun type retort has been elaborated, in which the latent and sensible heat of shale coke is well utilized. But the capacity of such retort is relatively small, therefore it is suitable for use in small or medium oil plants. China has a policy of steadily developing shale oil industry. China is conducting oil shale research and developing oil shale processing technology. Much attention is being pay ed to the comprehensive utilization of oil shale, shale oil, and to environmental problems. In China, oil shale is mostly used for producing shale by retorting, attention will also be paid to direct combustion for power generation. Great achievements in oil shale research have been made in the eighties, and there will be a further development in the nineties. (author), 12 refs., 3 tabs

Treating oil shale

Energy Technology Data Exchange (ETDEWEB)

Dolbear, S H

1921-01-04

Oil shale is treated for the separation of the valuable organic compounds, with a view to economy in subsequent destructive distillation, by grinding to powder, mixing with water to form a pulp, adding a small quantity of an oil liquid and aerating the mixture to form a froth containing the organic compounds. If the powdered shale contains sufficient free oil, the addition of oil to the pulp may be dispensed with. In some cases an electrolyte such as sulfuric acid may be added to the pulp.

Oil refineries

International Nuclear Information System (INIS)

Boehmer, S.; Winter, B.

2001-01-01

In refineries in particular attention is paid to the minimization of the generation of waste. Therefor catalysts in many processes are regenerated, absorbents are recycled and oily by-products are re-refined or used as fuels. This study discusses the origin and utilization of by-products from the oil industry. The processing of crude oils causes by-products and waste resulting from the crude oil itself or from cleaning measures for water pre-treatment, effluent treatment and flue gas treatment. (author)

Sorption of oil in the polyurethane from oil or castor oil; Sorcao de oleo no poliuretano derivado do petroleo ou do oleo de mamona

Energy Technology Data Exchange (ETDEWEB)

Florentino, Wagner M; Goulart, Shane A.S.; Mulinari, Daniella R. [Centro Universitario de Volta Redonda (UniFOA), Volta Redonda, RJ (Brazil)], e-mail: wagner-can@hotmail.com

2011-07-01

The oil outpouring has caused serious environmental problems. To minimize this damage polyurethane foams have been used. In this work, the use of polyurethane from oil and castor oil, in different polyol/diisocyanate mass ratios, to absorb oil was evaluated. Results revealed that the proportion of polyol and diisocyanate influenced in the sorption capacity and the polyurethane from castor oil presented greater sorption capacity. Of this way, can say that the polyurethane from oil can be replaced by castor oil, contributing to sustainable development. (author)

Oil companies make cutbacks

International Nuclear Information System (INIS)

Dupin, Ludovic

2014-01-01

As oil prices are falling, the oil sector faces company restructuring, merger projects, closure of oil fields, and so on. Restructuring is motivated by the costs of offshore exploration and oil production projects. Saudi Arabia tries to fight the emergence of shale gases by reducing oil prices, and somehow succeeds as some projects in the USA are put into question again. Experts perceive this situation as an opportunity for the sector to improve its efficiency and reduce over-staffing

Lavender oil

Science.gov (United States)

Lavender oil is an oil made from the flowers of lavender plants. Lavender poisoning can occur when ... further instructions. This is a free and confidential service. All local poison control centers in the United ...

An overview of empty fruit bunch from oil palm as feedstock for bio-oil production

International Nuclear Information System (INIS)

Chang, Siu Hua

2014-01-01

Empty fruit bunch (EFB) from oil palm is one of the potential biomass to produce biofuels like bio-oil due to its abundant supply and favorable physicochemical characteristics. Confirming the assertion, this paper presents an overview of EFB as a feedstock for bio-oil production. The fundamental characteristics of EFB in terms of proximate analysis, ultimate analysis and chemical composition, as well as the recent advances in EFB conversion processes for bio-oil production like pyrolysis and solvolysis are outlined and discussed. A comparison of properties in terms of proximate analysis, ultimate analysis and fuel properties between the bio-oil from EFB and petroleum fuel oil is included. The major challenges and future prospects towards the utilization of EFB as a useful resource for bio-oil production are also addressed. - Highlights: • Palm EFB has high heating value and low greenhouse gas emissions during combustion. • Conversion of EFB to bio-oil is mainly by fast pyrolysis without and with catalyst. • Bio-oil from EFB is lower in heating value, heavier and more acidic than fuel oil. • The viscosity of bio-oil from EFB is between those of light and heavy fuel oils. • The flash and pour points of bio-oil from EFB are close to those of light fuel oil

Fractional distillation of oil

Energy Technology Data Exchange (ETDEWEB)

Jones, L D

1931-10-31

A method of dividing oil into lubricating oil fractions without substantial cracking by introducing the oil in a heated state into a fractionating column from which oil fractions having different boiling points are withdrawn at different levels, while reflux liquid is supplied to the top of the column, and additional heat is introduced into the column by contacting with the oil therein a heated fluid of higher monlecular weight than water and less susceptible to thermal decomposition than is the highest boiling oil fraction resulting from the distillation, or of which any products produced by thermal decomposition will not occur in the highest boiling distillate withdrawn from the column.

Restructuring: new relationships between the oil companies and the upstream oil firms

International Nuclear Information System (INIS)

Barreau, S.

2001-11-01

Since the 1986 oil shock, international oil companies have focused on their base competencies, concentrating on activities viewed as their core businesses and steadily increasing the number of tasks to be subcontracted to the upstream oil and gas service sector. The upstream oil and gas service companies had to be restructured to face this new challenge. The strategies they launched at the end of the 80's were varied. Some firms became largely integrated (Schlumberger, Baker Hughes, Halliburton) whereas other firms chose to broaden their range of services. However generally, they opted for external investment which led to an important wave of mergers and acquisitions. The first part characterizes the upstream oil and gas sector by introducing the main oil and gas service firms and their recent strategic evolution. This concludes with both an economic valuation and a typology of attempted growth strategies. To illustrate this, a matrix has been created to characterise the dynamic paths of the oil and gas service firms. The purpose of the second part is to consider the economic theories related to industrial strategies. The strategies of innovation, market protection, vertical integration and diversification have been studied to illustrate the main conclusion which is that the aim of all these strategies was to change the relationships between the oil companies and the upstream oil and gas service firms. (author)

Enrichment of Fusobacteria in Sea Surface Oil Slicks from the Deepwater Horizon Oil Spill

OpenAIRE

Gutierrez, Tony; Berry, David; Teske, Andreas; Aitken, Michael D.

2016-01-01

The Deepwater Horizon (DWH) oil spill led to rapid microbial community shifts in the Gulf of Mexico, including the formation of unprecedented quantities of marine oil snow (MOS) and of a massive subsurface oil plume. The major taxa that bloomed in sea surface oil slicks during the spill included Cycloclasticus, and to a lesser extent Halomonas, Alteromonas, and Pseudoalteromonas?organisms that grow and degrade oil hydrocarbons aerobically. Here, we show that sea surface oil slicks at DWH cont...

Oil: Economics and politics

International Nuclear Information System (INIS)

Ayoub, A.

1994-01-01

A review is presented of the evolution of the international petroleum sector since 1973 with a special emphasis on the interdependence between the economic and political factors that influence it. Two issues are focused on: the effects of the nationalization of oil companies on the sharing of oil rents and on changes in the structure of the oil market; and the determination of oil prices. Definitions are presented of oil rents, and the reasons for OPEC nationalization of oil companies are explored. The effects of nationalization on market structures, expansion of free markets, and vertical integration are discussed. The existence of an oil price floor and the reasons for such a floor are examined. It is shown that nationalization induced an internalization of rents by the producing countries, leading to the emergence of a differential rent supported by the politics of the industrialized countries. Nationalization led to the breakup of systems of vertical and horizontal integration, with replacement by a new dual structure with OPEC controlling the upstream activities of the oil sector and oil companies controlling the downstream ones. Prices move between a floor price set by the costs of substitute deposits in the U.S., while the determination of ceiling levels by OPEC rests on successive fragile compromises. Overall oil is still a strategic product, despite the existence of spot markets, forward trading options, etc. 29 refs

SOVENT BASED ENHANCED OIL RECOVERY FOR IN-SITU UPGRADING OF HEAVY OIL SANDS

Energy Technology Data Exchange (ETDEWEB)

Munroe, Norman

2009-01-30

With the depletion of conventional crude oil reserves in the world, heavy oil and bitumen resources have great potential to meet the future demand for petroleum products. However, oil recovery from heavy oil and bitumen reservoirs is much more difficult than that from conventional oil reservoirs. This is mainly because heavy oil or bitumen is partially or completely immobile under reservoir conditions due to its extremely high viscosity, which creates special production challenges. In order to overcome these challenges significant efforts were devoted by Applied Research Center (ARC) at Florida International University and The Center for Energy Economics (CEE) at the University of Texas. A simplified model was developed to assess the density of the upgraded crude depending on the ratio of solvent mass to crude oil mass, temperature, pressure and the properties of the crude oil. The simplified model incorporated the interaction dynamics into a homogeneous, porous heavy oil reservoir to simulate the dispersion and concentration of injected CO2. The model also incorporated the characteristic of a highly varying CO2 density near the critical point. Since the major challenge in heavy oil recovery is its high viscosity, most researchers have focused their investigations on this parameter in the laboratory as well as in the field resulting in disparaging results. This was attributed to oil being a complex poly-disperse blend of light and heavy paraffins, aromatics, resins and asphaltenes, which have diverse behaviors at reservoir temperature and pressures. The situation is exacerbated by a dearth of experimental data on gas diffusion coefficients in heavy oils due to the tedious nature of diffusivity measurements. Ultimately, the viscosity and thus oil recovery is regulated by pressure and its effect on the diffusion coefficient and oil swelling factors. The generation of a new phase within the crude and the differences in mobility between the new crude matrix and the

[Imperial Oil's Cold Lake oil sands operations

International Nuclear Information System (INIS)

Dingle, H. B.

1999-01-01

Imperial Oil Limited's Cold Lake oil sands resources, production and operations in Alberta are discussed. Cold Lake is the company's largest single asset and its largest source of crude oil production. In 1998, Cold Lake accounted for just under half of Imperial's total liquid production, averaging more than 135,000 barrels of bitumen a day. Despite the very difficult operating conditions experienced by the oil sands industry in 1998, Imperial Oil's Cold Lake operations generated a positive cash flow and earnings. Just as important, the near and long-term potential of Cold Lake property continues to be strong, even with the tough market conditions today and the foreseeable future. Proved reserves at the end of 1997 were 1.3 billions barrels, equal to about 24 years of current production, but even more important is Imperial's resource base in the Athabasca region, which represents 150 years of production at current rates. Although production forecasts for the near future are are revised downward because of production shut-in due to low prices, the company is confident of its long-term prospects mainly because of existing infrastructure, superior reservoir quality, 30 years worth of operating improvements and established bitumen-blend markets. Details of the company's future Cold Lake development plans are discussed. The need to continue technology development, which has been at the core of the industry's growth in the past and will continue to be the key to the future, are emphasized

An experimental study on oil supply in a space bearing with an oil-impregnated retainer

Science.gov (United States)

Liu, Jianhai; Fan, Youwen; Wen, Shizhu

1993-06-01

Parched elastohydrodynamic lubrication (EHL) film thickness in a space ball bearing is measured by electrical capacitance and resistance, and parched transients of oil film and lubricant breakdown are observed. With different oil-impregnated polymer retainers, which are employed as oil supply resources, parched degradation is restricted to some degree, even lubricant breakdown disappears and a steady state of the oil film is produced. A long-term space bail bearing demands both the lowest driving torque and a steady state oil film, which depends on a strictly controlled oil supply from oil-impregnated retainers. The results of this experimental research describe the effects of oil supply by amounts of oil in retainers on parched EHL.

Competitiveness in the Brazilian oil industry. The Brazilian 'oil diamond'

International Nuclear Information System (INIS)

Zamith, R.; Moutinho Dos Santos, E.

2000-01-01

It is recognized the economic benefits that might follow the opening process of the Brazilian oil and natural gas industry, which shall experience a fast expansion with the arrival of national and international private investors. However, we should not neglect the broader impact of this process on the future development of all that cluster of national agents that lived around and served the former national oil monopoly, managed by the Brazilian National Oil Company, Petrobras. This work focuses on this larger perspective, discussing about the capacity of Brazil to sustain and expand its competitiveness in the oil business as well as to obtain the maximum economic development from the exploration of its oil and gas reserves. We adopt the work of Michael Porter, from the University of Harvard, about the Competitive Advantage of Nations, as a theoretical model to analyze the Competitive Advantage of Brazil in the global oil industry. By introducing the concept of ''oil diamond'', adapted from the notion introduced by this author, we develop a new understanding of national competitiveness in the oil sector. In this paper, we present the general model as well as a brief characterization of the results found for Brazil Subsequently, we focus on just one leg of the model, for which we discuss, with more detail, about the competitive condition of the country in the opening-up scenario. This leg regards the so-called supporting and supplementary industries that constitute what is denominated in the French tradition the ''para petroleum'' industry. We analyze the conditions for the Brazilian domestic ''para petroleum industry'' to survive and grow in the new competitive environment. (authors)

Applications of supercritical fluid extraction (SFE) of palm oil and oil from natural sources.

Science.gov (United States)

Akanda, Mohammed Jahurul Haque; Sarker, Mohammed Zaidul Islam; Ferdosh, Sahena; Manap, Mohd Yazid Abdul; Ab Rahman, Nik Norulaini Nik; Ab Kadir, Mohd Omar

2012-02-10

Supercritical fluid extraction (SFE), which has received much interest in its use and further development for industrial applications, is a method that offers some advantages over conventional methods, especially for the palm oil industry. SC-CO₂ refers to supercritical fluid extraction (SFE) that uses carbon dioxide (CO₂) as a solvent which is a nontoxic, inexpensive, nonflammable, and nonpolluting supercritical fluid solvent for the extraction of natural products. Almost 100% oil can be extracted and it is regarded as safe, with organic solvent-free extracts having superior organoleptic profiles. The palm oil industry is one of the major industries in Malaysia that provides a major contribution to the national income. Malaysia is the second largest palm oil and palm kernel oil producer in the World. This paper reviews advances in applications of supercritical carbon dioxide (SC-CO₂) extraction of oils from natural sources, in particular palm oil, minor constituents in palm oil, producing fractionated, refined, bleached, and deodorized palm oil, palm kernel oil and purified fatty acid fractions commendable for downstream uses as in toiletries and confectionaries.

RADARSAT SAR data assessment of oil lakes in the Greater Burgan Oil Field, Kuwait

International Nuclear Information System (INIS)

Kwarteng, A. Y.; Al-Ajmi, D.; Singhroy, V.; Saint-Jean, R.

1997-01-01

RADARSAT images recorded in different beam modes were processed and used to assess the oil lakes in the Burgan oil field in Kuwait created by the fire setting of oil wells by the retreating Iraqi forces in the 1990-1991 Gulf War. The images were geometrically registered to each other and used as input to a change detection program. The main interest was to map and differentiate between the oil lakes, tarmats, vegetation, buried oil lakes, and also to evaluate the usefulness of RADARSAT's beam modes in characterizing such features. Results of the RADARSAT imagery analysis were compared to similar studies using optical and SIR-C/X-SAR data. Initially, there have approximately 300 oil lakes covering an area of about 49 sq km. Twenty-one million barrels of oil were recovered and exported; about one million barrels of unrecoverable oil was left in the oil fields. Since then most of the oil has evaporated, dried up to form tarmats, or has been covered by a veneer of sand and is no longer visible on the surface

Applications of Supercritical Fluid Extraction (SFE of Palm Oil and Oil from Natural Sources

Directory of Open Access Journals (Sweden)

Mohd Omar Ab Kadir

2012-02-01

Full Text Available Supercritical fluid extraction (SFE, which has received much interest in its use and further development for industrial applications, is a method that offers some advantages over conventional methods, especially for the palm oil industry. SC-CO2 refers to supercritical fluid extraction (SFE that uses carbon dioxide (CO2 as a solvent which is a nontoxic, inexpensive, nonflammable, and nonpolluting supercritical fluid solvent for the extraction of natural products. Almost 100% oil can be extracted and it is regarded as safe, with organic solvent-free extracts having superior organoleptic profiles. The palm oil industry is one of the major industries in Malaysia that provides a major contribution to the national income. Malaysia is the second largest palm oil and palm kernel oil producer in the World. This paper reviews advances in applications of supercritical carbon dioxide (SC-CO2 extraction of oils from natural sources, in particular palm oil, minor constituents in palm oil, producing fractionated, refined, bleached, and deodorized palm oil, palm kernel oil and purified fatty acid fractions commendable for downstream uses as in toiletries and confectionaries.

Oil shale, shale oil, shale gas and non-conventional hydrocarbons

Directory of Open Access Journals (Sweden)

Clerici A.

2015-01-01

Full Text Available In recent years there has been a world “revolution” in the field of unconventional hydrocarbon reserves, which goes by the name of “shale gas”, gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also “oil shales” (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil, extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

Tracking an oil slick from multiple natural sources, Coal Oil Point, California

International Nuclear Information System (INIS)

Leifer, Ira; Luyendyk, Bruce; Broderick, Kris

2006-01-01

Oil slicks on the ocean surface emitted from natural marine hydrocarbon seeps offshore from Coal Oil Point in the Santa Barbara Channel, California were tracked and sampled over a 2-h period. The objectives were to characterize the seep oil and to track its composition over time using a new sampling device, a catamaran drum sampler (CATDRUMS). The sampler was designed and developed at UCSB. Chromatograms showed that oil originating from an informally named, very active seep area, Shane Seep, primarily evolved during the first hour due to mixing with oil originating from a convergence zone slick surrounding Shane Seep. (author)

Tracking an oil slick from multiple natural sources, Coal Oil Point, California

Energy Technology Data Exchange (ETDEWEB)

Leifer, Ira [Marine Sciences Institute, University of California, Santa Barbara, CA 93106 (United States); Luyendyk, Bruce [Department of Geological Sciences, University of California, Santa Barbara, CA 93106 (United States); Broderick, Kris [Exxon/Mobil Exploration Company, 13401 N. Freeway, Houston, TX 77060 (United States)

2006-06-15

Oil slicks on the ocean surface emitted from natural marine hydrocarbon seeps offshore from Coal Oil Point in the Santa Barbara Channel, California were tracked and sampled over a 2-h period. The objectives were to characterize the seep oil and to track its composition over time using a new sampling device, a catamaran drum sampler (CATDRUMS). The sampler was designed and developed at UCSB. Chromatograms showed that oil originating from an informally named, very active seep area, Shane Seep, primarily evolved during the first hour due to mixing with oil originating from a convergence zone slick surrounding Shane Seep. (author)

The oil barrel price

International Nuclear Information System (INIS)

Blondy, J.; Papon, P.

2009-01-01

This paper proposes an overview and a prospective glance on the oil barrel price. It indicates the relevant indicators: Brent quotation, euro/dollar parity, economic activity indicators, world oil consumption distribution, crude oil production, refining capacity. It briefly presents the involved stake holders: crude oil producers, oil refiners, refined product dealers, and the OPEC. It discusses the major retrospective trends: evolution in relationship with geopolitical events and energy policies, strong correlation between oil demand and economic growth, prevalence of OPEC, growing importance of national oil companies. An emerging trend is noticed: growing role of emerging countries on the crude market. Some prospective issues are discussed: duration and intensity of economic recession, separation between economic growth and energy consumption, pace and ambition level of policies of struggle against climate change, exploitable resources, and geopolitical hazards. Four evolution hypotheses are discussed

Calendula oil processing : seed classification, oil extraction, refining process development and oil quality aspects

NARCIS (Netherlands)

Janssens, R.J.J.

2000-01-01

The difference in Calendula oil quality from fractions obtained after seed classification is enormous. The oil quality varies from excellent to very poor, according to important aspects such as in the hulls and dust fraction, high free fatty acid values (13% vs. 0.6%) are found. This can be

Femtosecond laser ablation of highly oriented pyrolytic graphite: a green route for large-scale production of porous graphene and graphene quantum dots

Science.gov (United States)

Russo, Paola; Hu, Anming; Compagnini, Giuseppe; Duley, Walter W.; Zhou, Norman Y.

2014-01-01

Porous graphene (PG) and graphene quantum dots (GQDs) are attracting attention due to their potential applications in photovoltaics, catalysis, and bio-related fields. We present a novel way for mass production of these promising materials. The femtosecond laser ablation of highly oriented pyrolytic graphite (HOPG) is employed for their synthesis. Porous graphene (PG) layers were found to float at the water-air interface, while graphene quantum dots (GQDs) were dispersed in the solution. The sheets consist of one to six stacked layers of spongy graphene, which form an irregular 3D porous structure that displays pores with an average size of 15-20 nm. Several characterization techniques have confirmed the porous nature of the collected layers. The analyses of the aqueous solution confirmed the presence of GQDs with dimensions of about 2-5 nm. It is found that the formation of both PG and GQDs depends on the fs-laser ablation energy. At laser fluences less than 12 J cm-2, no evidence of either PG or GQDs is detected. However, polyynes with six and eight carbon atoms per chain are found in the solution. For laser energies in the 20-30 J cm-2 range, these polyynes disappeared, while PG and GQDs were found at the water-air interface and in the solution, respectively. The origin of these materials can be explained based on the mechanisms for water breakdown and coal gasification. The absence of PG and GQDs, after the laser ablation of HOPG in liquid nitrogen, confirms the proposed mechanisms.Porous graphene (PG) and graphene quantum dots (GQDs) are attracting attention due to their potential applications in photovoltaics, catalysis, and bio-related fields. We present a novel way for mass production of these promising materials. The femtosecond laser ablation of highly oriented pyrolytic graphite (HOPG) is employed for their synthesis. Porous graphene (PG) layers were found to float at the water-air interface, while graphene quantum dots (GQDs) were dispersed in the

MICROWAVE HEATING AND SEPARATION OF WATER-IN-OIL EMULSION FROM MEXICAN CRUDE OIL

OpenAIRE

VAZQUEZ V., ADRIAN; LOPEZ M., ARTURO; ANDRADE C., LUIS J.; VAZQUEZ A., ARIANA M.

2014-01-01

Microwave heating and gravity sedimentation are alternatives for demulsification and layer separation into oil and water layers, this process was demonstrated in the laboratory and provides an option for reducing and oil recovering from water-in-oil Mexican oil emulsions. The combinatorial process was implemented in a test lab using Mexican crude oil samples. The Laboratory samples were 100% and 50-50%, crude and crude-water respectively, were heated. The results were encouraging show that mi...

Geopolitics of oil markets

International Nuclear Information System (INIS)

Liscom, W.L.

1991-01-01

Geopolitics can inject a great deal of uncertainty and cause fundamental shifts in the overall direction of oil markets, which would otherwise act in a fairly predictable and stable manner. The Iraqi invasion of Kuwait and the response of the USA were definitely linked with oil, and the aftermath of the invasion left four geopolitical issues affecting world oil markets. The provision authorizing $1.6 billion in Iraqi oil exports under the United Nations sanctions was imposed with little concern about the potential impact of these exports on the oil market; Iraq could export as much as 1 million bbl/d and it is unlikely that exports would be stopped once the $1.6 billion limit is reached. By making up most of the supply shortfall during the Kuwait crisis, Saudi Arabia suddenly became the producer of over a third of OPEC oil supplies and now dominates OPEC. The Saudis have indicated it will swing production according to world demand, irrespective of what OPEC wants, so that world oil demand will return strongly and remain. Middle East politics in general will determine the stability of oil supplies in the region for many of the countries. A producer-consumer dialogue at the high governmental level has started, with a view to some type of multilateral understanding in the light of mutual interests in secure oil supplies. This is not likely to have a big impact on oil markets without participation and support from the USA. The recent changes in the Soviet Union have potential impacts in regard to the attraction of that market for Western investment, in particular to assist exports. The worldwide environmental movement will also play a geopolitical role in the world oil market due to its influence on oil taxation policies

Manitoba oil activity review, 1996

International Nuclear Information System (INIS)

1997-01-01

This report is the annual review of Manitoba Crown oil and gas dispositions, mineral owner leasing and revenue, geophysical and drilling activity, areas of activity, oil production and markets, oil prices, value of production, provincial revenue from oil production, surface owners, spills and reclamation, municipal taxes, the Manitoba Drilling Incentive Program, oil reserves, oil industry expenditures, and industry employment. Highlights of the current year are included

Manitoba oil activity review, 1997

International Nuclear Information System (INIS)

1998-01-01

Annual review is presented of Manitoba Crown oil and gas dispositions, mineral owner leasing and revenue, geophysical and drilling activity, areas of activity, oil production and markets, oil prices, value of production, provincial revenue from oil production, surface owners, spills and reclamation, municipal taxes, the Manitoba Drilling Incentive Program, oil reserves, oil industry expenditures, and industry employment. Highlights of the current year are included

Manitoba oil activity review, 1995

International Nuclear Information System (INIS)

1996-01-01

This report is the annual review of Manitoba Crown oil and gas dispositions, mineral owner leasing and revenue, geophysical and drilling activity, areas of activity, oil production and markets, oil prices, value of production, provincial revenue from oil production, surface owners, spills and reclamation, municipal taxes, the Manitoba Drilling Incentive Program, oil reserves, oil industry expenditures, and industry employment. Highlights of the current year are included

The oil market. Call on OPEC determines the oil price

International Nuclear Information System (INIS)

Kingma, D.; Mulder, M.

2001-01-01

Several scenarios are applied to determine the oil price for the medium-long term, based on the so-called 'call on OPEC'. The 'call on OPEC' is part of the demand for oil which has to supplied by OPEC. It is expected that the nominal oil price will be circa $24 per barrel in 2004, based on a global growth of 4%. 2 refs

Allocation of multiple, widely spread oil spills associated with one polluter : GC-MS fingerprinting and diagnostic ratios of spilled oil and oiled seabirds