WorldWideScience

Sample records for pyramidal structural defects

  1. Atomic structure of pyramidal defects in GaN:Mg: Influence of annealing

    Energy Technology Data Exchange (ETDEWEB)

    Liliental-Weber, Z.; Tomaszewicz, T.; Zakharov, D.; O' Keefe, M. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Hautakangas, S.; Saarinen, K. [Materials Science and Engineering, University of California, Berkeley, Berkeley, CA 94720 (United States); Freitas, J.A.; Henry, R.L. [ESTD-Electronic Materials Branch, Naval Research Laboratory, Washington, D.C. 20375 (United States)

    2006-05-15

    The atomic structure of the characteristic defects (Mg-rich hexagonal pyramids) in p-doped bulk and MOCVD GaN:Mg thin films grown with Ga polarity was determined at atomic resolution by direct reconstruction of the scattered electron wave in a transmission electron microscope. Small cavities were present inside the defects, confirmed also with positron annihilation. The inside walls of the cavities were covered by GaN of reverse polarity compared to the matrix. Annealing of the MOCVD layers lead to slight increase of the defect size and an increase of the room temperature photoluminescence intensity. Positron annihilation confirms presence of vacancy clusters of different sizes triggered by the Mg doping in as-grown samples and decrease of their concentration upon annealing at 900 and 1000 C. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. Field emission properties of an array of pyramidal structures

    Energy Technology Data Exchange (ETDEWEB)

    De Assis, Thiago A [Departamento de QuImica, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Borondo, F [Departamento de QuImica, Instituto Mixto de Ciencias Matematicas CSIC-UAM-UC3M-UCM, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); De Castilho, C M C; Brito Mota, F [Grupo de Fisica de SuperfIcies e Materiais, Instituto de Fisica, Universidade Federal da Bahia, Campus Universitario da Federacao, 40210-340, Salvador, BA (Brazil); Benito, R M, E-mail: t.albuquerque@uam.e, E-mail: f.borondo@uam.e, E-mail: caio@ufba.b, E-mail: fbmota@ufba.b, E-mail: rosamaria.benito@upm.e [Grupo de Sistemas Complejos, Departamento de Fisica y Mecanica, Escuela Tecnica Superior de Ingenieros Agronomos, Universidad Politecnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain)

    2009-10-07

    The properties and efficiency of the emission current density produced by a metallic array of pyramidal structures are investigated. The theoretical results obtained by numerical integration of the corresponding Laplace equation using a finite differences scheme offer useful information for the optimization of field emission devices based on cathodes with this geometry. Our study shows that the inter-pyramidal distance strongly affects the current density, and even more important for this issue is the protrusion characteristics of these structures. Another relevant, although less important, parameter determining this density is the anode-cathode distance. The effect of the array characteristics on the maximum local electric field intensity is also discussed.

  3. PLAN FOR PERFORMANCE ADMINISTRATION IN PYRAMIDAL STRUCTURE ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    Domingo Alarcón Ortiz

    2013-11-01

    Full Text Available Performance administration has become a current strategy in evaluating management within organizations, but its implementation often lacks an action plan, resulting from the valuation of climate and leadership styles embedded in the culture of the organization. This paper proposes a model action plan for performance management, which has been implemented, executed and evaluated in pyramidal organizational structure organizations where a diagnosis of the cultural climate and leadership styles recurring in the organization have been previously made.

  4. The Orientations of the Giza Pyramids and Associated Structures

    Science.gov (United States)

    Nell, Erin; Ruggles, Clive

    2014-08-01

    Ever since Flinders Petrie undertook a theodolite survey on the Giza plateau in 1881 and drew attention to the extraordinary degree of precision with which the three colossal pyramids are oriented upon the four cardinal directions, there have been a great many suggestions as to how this was achieved and why it was of importance. Surprisingly, given the many astronomical hypotheses and speculations that have been offered in the intervening 130 years, there have been remarkably few attempts to reaffirm or improve on the basic survey data concerning the primary orientations. This paper presents the results of a week-long Total Station survey undertaken by the authors during December 2006 whose principal aim was to clarify the basic data concerning the orientation of each side of the three large pyramids and to determine, as accurately as possible, the orientations of as many as possible of the associated structures. The principal difference between this and all previous surveys is that it focuses upon measurements of sequences of points along multiple straight and relatively well preserved structural segments, with best-fit techniques being used to provide the best estimate of their orientation, as opposed to simple triangulation between directly identified or extrapolated corners. Our results suggest that there is only a very slight difference in orientation (c. 0.5 arc minutes) between the north-south axes of Khufu's and Khafre's pyramids, that the sides of Khafre's are more perfectly perpendicular than those of Khufu's, and that the east-west axis is closer to true cardinality in both cases. The broader context of associated structures suggests that the east-west orientation in relation to sunrise or (in one case) sunset may have been a, or even the, key factor in many cases.

  5. Micromagnetic studies of three-dimensional pyramidal shell structures

    International Nuclear Information System (INIS)

    Knittel, A; Franchin, M; Fischbacher, T; Fangohr, H; Nasirpouri, F; Bending, S J

    2010-01-01

    We present a systematic numerical analysis of the magnetic properties of pyramidal-shaped core-shell structures in a size range below 400 nm. These are three-dimensional structures consisting of a ferromagnetic shell which is grown on top of a non-magnetic core. The standard micromagnetic model without the magnetocrystalline anisotropy term is used to describe the properties of the shell. We vary the thickness of the shell between the limiting cases of an ultra-thin shell and a conventional pyramid and delineate different stable magnetic configurations. We find different kinds of single-domain states, which predominantly occur at smaller system sizes. In analogy to equivalent states in thin square films we term these onion, flower, C and S states. At larger system sizes, we also observe two types of vortex states, which we refer to as symmetric and asymmetric vortex states. For a classification of the observed states, we derive a phase diagram that specifies the magnetic ground state as a function of structure size and shell thickness. The transitions between different ground states can be understood qualitatively. We address the issue of metastability by investigating the stability of all occurring configurations for different shell thicknesses. For selected geometries and directions hysteresis measurements are analysed and discussed. We observe that the magnetic behaviour changes distinctively in the limit of ultra-thin shells. The study has been motivated by the recent progress made in the growth of faceted core-shell structures.

  6. The pyramid model as a structured way of quality management

    Directory of Open Access Journals (Sweden)

    van der Tuuk Adriani Willem

    2008-01-01

    Full Text Available Three quality systems that can be used in blood establishments are briefly explained. The Pyramid model is described as a tool to manage the quality systems. Finally, some experiences in other countries are given to prove the validity of the system.

  7. Packing defects into ordered structures

    DEFF Research Database (Denmark)

    Bechstein, R.; Kristoffersen, Henrik Høgh; Vilhelmsen, L.B.

    2012-01-01

    . With the help of density functional theory calculations we develop a complete structural model for the entire strand and demonstrate these adstructures to be more stable than an equivalent amount of bulk defects such as Ti interstitials. We argue that strands can form particularly easy on stepped surfaces......We have studied vicinal TiO2(110) surfaces by high-resolution scanning tunneling microscopy and density functional theory calculations. On TiO2 surfaces characterized by a high density of ⟨11̅ 1⟩ steps, scanning tunneling microscopy reveals a high density of oxygen-deficient strandlike adstructures...

  8. Design and Preparation of a Micro-Pyramid Structured Thin Film for Broadband Infrared Antireflection

    Directory of Open Access Journals (Sweden)

    Shaobo Ge

    2018-05-01

    Full Text Available A micro-pyramid structured thin film with a broad-band infrared antireflection property is designed and fabricated by using the single-point diamond turning (SPDT technique and combined with nano-imprint lithography (NIL. A structure with dimensions of 10 μm pitch and 5 μm height is transferred from the copper mold to the silicon nitride optical film by using NIL and proportional inductively-coupled plasma (ICP etching. Reflectance of the micro-optical surface is reduced below 1.0% over the infrared spectral range (800–2500 nm. A finite-difference-time-domain (FDTD analysis indicates that this micro-structure can localize photons and enhance the absorption inside the micro-pyramid at long wavelengths. As described above, the micro-pyramid array has been integrated in an optical film successfully. Distinguishing from the traditional micro-optical components, considering the effect of refraction and diffraction, it is a valuable and flexible method to take account of the interference effect of optical film.

  9. Concurrent improvement in optical and electrical characteristics by using inverted pyramidal array structures toward efficient Si heterojunction solar cells

    KAUST Repository

    Wang, Hsin Ping; Li, An Cheng; Lin, Tzu Yin; He, Jr-Hau

    2016-01-01

    the devices is critical for boosting cell efficiency although it usually comes with the V loss caused by severe surface recombination. For the first time, the periodic inverted pyramid (IP) structure fabricated by photolithography and anisotropic etching

  10. Sulfolobus turreted icosahedral virus c92 protein responsible for the formation of pyramid-like cellular lysis structures.

    Science.gov (United States)

    Snyder, Jamie C; Brumfield, Susan K; Peng, Nan; She, Qunxin; Young, Mark J

    2011-07-01

    Host cells infected by Sulfolobus turreted icosahedral virus (STIV) have been shown to produce unusual pyramid-like structures on the cell surface. These structures represent a virus-induced lysis mechanism that is present in Archaea and appears to be distinct from the holin/endolysin system described for DNA bacteriophages. This study investigated the STIV gene products required for pyramid formation in its host Sulfolobus solfataricus. Overexpression of STIV open reading frame (ORF) c92 in S. solfataricus alone is sufficient to produce the pyramid-like lysis structures in cells. Gene disruption of c92 within STIV demonstrates that c92 is an essential protein for virus replication. Immunolocalization of c92 shows that the protein is localized to the cellular membranes forming the pyramid-like structures.

  11. Sulfolobus Turreted Icosahedral Virus c92 Protein Responsible for the Formation of Pyramid-Like Cellular Lysis Structures

    DEFF Research Database (Denmark)

    Snyder, Jamie C; Brumfield, Susan K; Peng, Nan

    2011-01-01

    Host cells infected by Sulfolobus turreted icosahedral virus (STIV) have been shown to produce unusual pyramid-like structures on the cell surface. These structures represent a virus-induced lysis mechanism that is present in Archaea and appears to be distinct from the holin/endolysin system desc...... disruption of c92 within STIV demonstrates that c92 is an essential protein for virus replication. Immunolocalization of c92 shows that the protein is localized to the cellular membranes forming the pyramid-like structures.......Host cells infected by Sulfolobus turreted icosahedral virus (STIV) have been shown to produce unusual pyramid-like structures on the cell surface. These structures represent a virus-induced lysis mechanism that is present in Archaea and appears to be distinct from the holin/endolysin system...... described for DNA bacteriophages. This study investigated the STIV gene products required for pyramid formation in its host Sulfolobus solfataricus. Overexpression of STIV open reading frame (ORF) c92 in S. solfataricus alone is sufficient to produce the pyramid-like lysis structures in cells. Gene...

  12. Defect structure of electrodeposited chromium layers

    International Nuclear Information System (INIS)

    Marek, T.; Suevegh, K.; Vertes, A.; El-Sharif, M.; McDougall, J.; Chisolm, C.U.

    2000-01-01

    Positron annihilation spectroscopy was applied to study the effects of pre-treatment and composition of substrates on the quality and defect structure of electrodeposited thick chromium coatings. The results show that both parameters are important, and a scenario is proposed why the mechanically polished substrate gives more defective film than the electro polished one.

  13. Defect structure of electrodeposited chromium layers

    Energy Technology Data Exchange (ETDEWEB)

    Marek, T. E-mail: marek@para.chem.elte.hu; Suevegh, K.; Vertes, A.; El-Sharif, M.; McDougall, J.; Chisolm, C.U

    2000-06-01

    Positron annihilation spectroscopy was applied to study the effects of pre-treatment and composition of substrates on the quality and defect structure of electrodeposited thick chromium coatings. The results show that both parameters are important, and a scenario is proposed why the mechanically polished substrate gives more defective film than the electro polished one.

  14. The Conflict Pyramid: A Holistic Approach to Structuring Conflict Resolution in Schools

    Science.gov (United States)

    Hakvoort, Ilse

    2010-01-01

    This paper examines how the conflict pyramid, originally defined and used by Richard Cohen, can be used as a model to describe the relations between different conflict resolution education programs and activities included in the programs. The central questions posed in the paper are: How can Richard Cohen's conflict pyramid be used as a model for…

  15. Marine and land active-source seismic investigation of geothermal potential, tectonic structure, and earthquake hazards in Pyramid Lake, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Eisses, A.; Kell, A.; Kent, G. [UNR; Driscoll, N. [UCSD; Karlin, R.; Baskin, R. [USGS; Louie, J. [UNR; Pullammanappallil, S. [Optim

    2016-08-01

    Amy Eisses, Annie M. Kell, Graham Kent, Neal W. Driscoll, Robert E. Karlin, Robert L. Baskin, John N. Louie, Kenneth D. Smith, Sathish Pullammanappallil, 2011, Marine and land active-source seismic investigation of geothermal potential, tectonic structure, and earthquake hazards in Pyramid Lake, Nevada: presented at American Geophysical Union Fall Meeting, San Francisco, Dec. 5-9, abstract NS14A-08.

  16. Electronic structure of point defects in semiconductors

    International Nuclear Information System (INIS)

    Bruneval, Fabien

    2014-01-01

    This 'Habilitation a diriger des Recherches' memoir presents most of my scientific activities during the past 7 years, in the field of electronic structure calculations of defects in solids. Point defects (vacancies, interstitials, impurities) in functional materials are a key parameter to determine if these materials will actually fill the role they have been assigned or not. Indeed, the presence of defects cannot be avoided when the temperature is increased or when the material is subjected to external stresses, such as irradiation in the nuclear reactors and in artificial satellites with solar radiations. However, in many cases, defects are introduced in the materials on purpose to tune the electronic transport, optical or even magnetic properties. This procedure is called the doping of semiconductors, which is the foundation technique for transistors, diodes, or photovoltaic cells. However, doping is not always straightforward and unexpected features may occur, such as doping asymmetry or Fermi level pinning, which can only be explained by complex phenomena involving different types of defects or complexes of defects. In this context, the calculations of electronic structure ab initio is an ideal tool to complement the experimental observations, to gain the understanding of phenomena at the atomic level, and even to predict the properties of defects. The power of the ab initio calculations comes from their ability to describe any system of electrons and nuclei without any specific adjustment. But although there is a strong need for numerical simulations in this field, the ab initio calculations for defects are still under development as of today. The work presented in this memoir summarizes my contributions to methodological developments on this subject. These developments have followed two main tracks. The first topic is the better understanding of the unavoidable finite size effects. Indeed, defects in semiconductors or insulators are generally present in

  17. Electronic structure of defects in semiconductor heterojunctions

    International Nuclear Information System (INIS)

    Haussy, Bernard; Ganghoffer, Jean Francois

    2002-01-01

    Full text.heterojunctions and semiconductors and superlattices are well known and well used by people interested in optoelectronics communications. Components based on the use of heterojunctions are interesting for confinement of light and increase of quantum efficiency. An heterojunction is the contact zone between two different semiconductors, for example GaAs and Ga 1-x Al x As. Superlattices are a succession of heterojunctions (up to 10 or 20). These systems have been the subjects of many experiments ao analyse the contact between semiconductors. They also have been theoretically studied by different types of approach. The main result of those studies is the prediciton of band discontinuities. Defects in heterojunctions are real traps for charge carriers; they can affect the efficiency of the component decreasing the currents and the fluxes in it. the knowledge of their electronic structure is important, a great density of defects deeply modifies the electronic structure of the whole material creating real new bands of energy in the band structure of the component. in the first part of this work, we will describe the heterostructure and the defect in terms of quantum wells and discrete levels. This approach allows us to show the role of the width of the quantum well describing the structure but induces specific behaviours due to the one dimensional modelling. Then a perturbative treatment is proposed using the Green's functions formalism. We build atomic chains with different types of atoms featuring the heterostructure and the defect. Densities of states of a structure with a defect and levels associated to the defect are obtained. Results are comparable with the free electrons work, but the modelling do not induce problems due to a one dimensional approach. To extend our modelling, a three dimensions approach, based on a cavity model, is investigated. The influence of the defect, - of hydrogenoid type - introduced in the structure, is described by a cavity

  18. Investigation of defect structures in solids

    Energy Technology Data Exchange (ETDEWEB)

    Dienel, G; Hubrig, W H; Schenk, M; Syhre, H [Zentralinstitut fuer Kernforschung, Rossendorf bei Dresden (German Democratic Republic)

    1976-01-01

    Some central points of interest of research in the field of defect structures in solids dealt with at the Central Institute of Nuclear Research at Rossendorf in the last years are presented. Studies on f.c.c. and b.c.c. metals, radiation-induced phase transitions in perovskites and ion-implanted silicon are described in some detail.

  19. INSTABILITY MODELING OF FINANCIAL PYRAMIDS

    OpenAIRE

    Girdzijauskas, Stasys; Moskaliova, Vera

    2005-01-01

    The financial structures that make use of money flow for “easy money” or cheating purpose are called financial pyramids. Recently financial pyramids intensively penetrates IT area. It is rather suitable way of the fraud. Money flow modeling and activity analysis of such financial systems allows identifying financial pyramids and taking necessary means of precautions. In the other hand even investing companies that function normally when market conditions changes (e.g. interest rates) eventual...

  20. Concurrent improvement in optical and electrical characteristics by using inverted pyramidal array structures toward efficient Si heterojunction solar cells

    KAUST Repository

    Wang, Hsin Ping

    2016-03-02

    The Si heterojunction (SHJ) solar cell is presently the most popular design in the crystalline Si (c-Si) photovoltaics due to the high open-circuit voltages (V). Photon management by surface structuring techniques to control the light entering the devices is critical for boosting cell efficiency although it usually comes with the V loss caused by severe surface recombination. For the first time, the periodic inverted pyramid (IP) structure fabricated by photolithography and anisotropic etching processes was employed for SHJ solar cells, demonstrating concurrent improvement in optical and electrical characteristics (i.e., short-circuit current density (J) and V). Periodic IP structures show superior light-harvesting properties as most of the incident rays bounce three times on the walls of the IPs but only twice between conventional random upright pyramids (UPs). The high minority carrier lifetime of the IP structures after a-Si:H passivation results in an enhanced V by 28 mV, showing improved carrier collection efficiency due to the superior passivation of the IP structure over the random UP structures. The superior antireflective (AR) ability and passivation results demonstrate that the IP structure has the potential to replace conventional UP structures to further boost the efficiency in solar cell applications.

  1. PYRAMID LAKE RENEWEABLE ENERGY PLAN

    Energy Technology Data Exchange (ETDEWEB)

    HIGH DESERT GEOCULTURE, LLC

    2009-06-06

    The Pyramid Lake Renewable Energy Plan covers these areas: energy potential (primarily focusing on geothermal resource potential, but also more generally addressing wind energy potential); renewable energy market potential; transmission system development; geothermal direct use potential; and business structures to accomplish the development objectives of the Pyramid Lake Paiute Tribe.

  2. Formation of Various Pyramidal Structures on Monocrystalline Silicon Surface and Their Influence on the Solar Cells

    Directory of Open Access Journals (Sweden)

    Yangang Han

    2013-01-01

    Full Text Available Texturization is a useful method to enhance the optical absorption of monocrystalline silicon wafers by light-trapping effect in solar cell processing. In present study, a series of textured wafers with various pyramid sizes ranging from 200 nm to 10 μm were fabricated by modified wet-chemical method and characterized. The results show that there is little difference in the reflectance with the pyramid sizes from 1 to 10 μm, which is consistent with the ray-tracing simulation results. However, the light-trapping function of the 200 nm sample below the geometrical optics limit is much weaker. The solar cells fabricated from the 1 μm samples own the highest power conversion efficiency of 18.17% due to a better coverage of metal finger lines than the larger ones, and the 200 nm samples have the lowest efficiency of 10.53%.

  3. Charged Semiconductor Defects Structure, Thermodynamics and Diffusion

    CERN Document Server

    Seebauer, Edmund G

    2009-01-01

    The technologically useful properties of a solid often depend upon the types and concentrations of the defects it contains. Not surprisingly, defects in semiconductors have been studied for many years, in many cases with a view towards controlling their behavior through various forms of "defect engineering." For example, in the bulk, charging significantly affects the total concentration of defects that are available to mediate phenomena such as solid-state diffusion. Surface defects play an important role in mediating surface mass transport during high temperature processing steps such as epitaxial film deposition, diffusional smoothing in reflow, and nanostructure formation in memory device fabrication. Charged Semiconductor Defects details the current state of knowledge regarding the properties of the ionized defects that can affect the behavior of advanced transistors, photo-active devices, catalysts, and sensors. Features: Group IV, III-V, and oxide semiconductors; Intrinsic and extrinsic defects; and, P...

  4. Defect Structure of Localized Excitons in a WSe2 Monolayer

    KAUST Repository

    Zhang, Shuai

    2017-07-26

    The atomic and electronic structure of intrinsic defects in a WSe2 monolayer grown on graphite was revealed by low temperature scanning tunneling microscopy and spectroscopy. Instead of chalcogen vacancies that prevail in other transition metal dichalcogenide materials, intrinsic defects in WSe2 arise surprisingly from single tungsten vacancies, leading to the hole (p-type) doping. Furthermore, we found these defects to dominate the excitonic emission of the WSe2 monolayer at low temperature. Our work provided the first atomic-scale understanding of defect excitons and paved the way toward deciphering the defect structure of single quantum emitters previously discovered in the WSe2 monolayer.

  5. Atomic structure of defects in GaN:Mg grown with Ga polarity

    International Nuclear Information System (INIS)

    Liliental-Weber, Z.; Tomaszewicz, T.; Zakharov, D.; Jasinski, J.; O'Keefe, M.A.; Hautakangas, S.; Laakso, A.; Saarinen, K.

    2003-01-01

    Electron microscope phase images, produced by direct reconstruction of the scattered electron wave from a focal series of high-resolution images, were used to determine the nature of defects formed in GaN:Mg crystals. We studied bulk crystals grown from dilute solutions of atomic nitrogen in liquid gallium at high pressure and thin films grown by the MOCVD method. All the crystals were grown with Ga-polarity. In both types of samples the majority of defects were three dimensional Mg-rich hexagonal pyramids with bases on the (0001) plane and six walls on {11(und 2)3} planes seen in cross-section as triangulars. Some other defects appear in cross-section as trapezoidal (rectangular) defects as a result of presence of truncated pyramids. Both type of defects have hollow centers. They are decorated by Mg on all six side walls and a base. The GaN which grows inside on the defect walls shows polarity inversion. It is shown that change of polarity starts from the defect tip and propagates to the base, and that the stacking sequence changes from ab in the matrix to bc inside the defect. Exchange of the Ga sublattice with the N sublattice within the defect leads to 0.6 ± 0.2(angstrom) displacement between Ga sublattices outside and inside the defects. It is proposed that lateral overgrowth of the cavities formed within the defect takes place to restore matrix polarity on the defect base

  6. Elastic interaction energies of defect structures

    International Nuclear Information System (INIS)

    Seitz, E.; de Fontaine, D.

    1976-01-01

    The elastic strain energy between point defects and small disk-shaped clusters of defects are calculated to determine stable configurations. A distortion tensor of tetragonal symmetry is assigned to each impurity atom. The tetragonality ratio t is varied to cover needle-type (t greater than 1), spherical (t = 1) and disk-type (t less than 0) strain fields. To vary the elastic properties of the host material, Fe, Cu, Al, and V were chosen as examples. Computer calculations are based on the microscopic theory of elasticity which emphasizes calculations in discrete Fourier space. Pairs of point defects order along [001] for t less than 1 and along (001) for t = 1 for all host elements. For t greater than 1 fcc lattices and bcc lattices behave differently. It is shown that only certain three dimensional periodic arrangements of parallel and perpendicular disk-like defect clusters are realized for given tetragonality ratio t and host element

  7. Co_3V_2O_8 Hexagonal Pyramid with Tunable Inner Structure as High Performance Anode Materials for Lithium Ion Battery

    International Nuclear Information System (INIS)

    Zhang, Qiang; Pei, Jian; Chen, Gang; Bie, Changfeng; Chen, Dahong; Jiao, Yang; Rao, Jiancun

    2017-01-01

    Co_3V_2O_8 hexagonal pyramid was successfully fabricated via a simple hydrothermal process and subsequent heat treatment. The inner structure of the hexagonal pyramid was further adjusted by controlling the size of Co_7V_4O_1_6(OH)_2(H_2O) precursors. Hierarchical Co_3V_2O_8 hexagonal pyramid with height of 1 μm were orderly constructed from 60–80 nm inter-connected particles, showing numerous interval voids. Benefiting from its unique structure, the as-prepared sample showed higher electrochemical performance as an anode material for lithium-ion batteries than that of another bulk sample with height of 5 μm and adhesive inner structure. When tested at a current density of 500 mA g"−"1, the hierarchical Co_3V_2O_8 hexagonal pyramid exhibited good rate capacity, high cycling stability, and excellent discharge capacity up to 712 mA h g"−"1, making it promising electrode materials for lithium-ion batteries.

  8. Imaging the Cheops Pyramid

    CERN Document Server

    Bui, H D

    2012-01-01

    In this book Egyptian Archeology  and Mathematics meet. The author is an expert in theories and applications in Solid Mechanics and Inverse Problems, a former professor at Ecole Polytechnique and now works with Electricité de France on maintenance operations on nuclear power plants. In the Autumn of 1986, after the end of the operation on the King’s chamber conducted under the Technological and Scientific Sponsorship of EDF, to locate a cavity, he was called to solve a mathematical inverse problem, to find the unknown tomb of the King and the density structure of the whole pyramid based on measurements of microgravity made inside and outside of the pyramid. This book recounts the various search operations on the pyramid of Cheops made at the request of the Egyptian and French authorities in 1986-1987. After the premature end of the Cheops operation in the Autumn of 1986, following the fiasco of unsuccessful drillings in the area suspected by both architects G. Dormion and J.P. Goidin and microgravity aus...

  9. Defect structure in proton-irradiated copper and nickel

    International Nuclear Information System (INIS)

    Tsukuda, Noboru; Ehrhart, P.; Jaeger, W.; Schilling, W.; Dworschak, F.; Gadalla, A.A.

    1987-01-01

    This single crystals of copper or nickel with a thickness of about 10 μm are irradiated with 3 MeV protons at room temperature and the structures of resultant defects are investigated based on measurements of the effects of irradiation on the electrical resistivity, length, lattice constants, x-ray diffraction line profile and electron microscopic observations. The measurements show that the electrical resistivity increases with irradiation dose, while leveling off at high dose due to overlapping of irradiation cascades. The lattice constants decreases, indicating that many vacancies still remain while most of the interstitial stoms are eliminated, absorbed or consumed for dislocation loop formation. The x-ray line profile undergoes broadening, which is the result of dislocation loops, dislocation networks and SFT's introduced by the proton irradiation. Various defects have different effects though they cannot be identified separately from the profile alone. A satellite peak appears at a low angle, which seems to arise from periodic defect structures that are found in electron microscopic observations. In both copper and nickel, such periodic defect structures are seen over a wide range from high to low dose. Defect-free and defect-rich domains (defect walls), 0.5 to several μm in size, are alingned parallel to the {001} plane at intervals of 60 nm. The defect walls, which consist of dislocations, dislocation loops and SFT's, is 20 - 40 nm thick. (Nogami, K.)

  10. First-principles study of structural & electronic properties of pyramidal silicon nanowire

    Energy Technology Data Exchange (ETDEWEB)

    Jariwala, Pinank; Thakor, P. B. [Department of Physics, Veer Narmad South Gujarat University, Surat 395 007, Gujarat (India); Singh, Deobrat; Sonvane, Y. A., E-mail: yasonvane@gmail.com [Department of Applied Physics, S. V. National Institute of Technology, Surat 395 007 (India); Gupta, Sanjeev K. [Department of Physics, St. Xavier’s College, Ahmedabad 38 0009 (India)

    2016-05-23

    We have investigated the stable structural and electronic properties of Silicon (Si) nanowires having different cross-sections with 5-7 Si atoms per unit cell. These properties of the studied Si nanowires were significantly changed from those of diamond bulk Si structure. The binding energy increases as increasing atoms number per unit cell in different SiNWs structures. All the nanowires structures are behave like metallic rather than semiconductor in bulk systems. In general, the number of conduction channels increases when the nanowire becomes thicker. The density of charge revealed delocalized metallic bonding for all studied Si nanowires.

  11. Urban public health: is there a pyramid?

    Science.gov (United States)

    Su, Meirong; Chen, Bin; Yang, Zhifeng; Cai, Yanpeng; Wang, Jiao

    2013-01-28

    Early ecologists identified a pyramidal trophic structure in terms of number, biomass and energy transfer. In 1943, the psychologist Maslow put forward a pyramid model to describe layers of human needs. It is indicated that the pyramid principle is universally applicable in natural, humanistic and social disciplines. Here, we report that a pyramid structure also exists in urban public health (UPH). Based on 18 indicators, the UPH states of four cities (Beijing, Tokyo, New York, and London) are compared from the point of view of five aspects, namely physical health, living conditions, social security, environmental quality, and education and culture. A pyramid structure was found in each city when focusing on 2000-2009 data. The pyramid of Beijing is relatively similar to that of Tokyo, and the pyramids of New York and London are similar to each other. A general development trend in UPH is proposed and represented by different pyramid modes. As a basic conjecture, the UPH pyramid model can be verified and developed with data of more cities over a longer period, and be used to promote healthy urban development.

  12. Urban Public Health: Is There a Pyramid?

    Directory of Open Access Journals (Sweden)

    Meirong Su

    2013-01-01

    Full Text Available Early ecologists identified a pyramidal trophic structure in terms of number, biomass and energy transfer. In 1943, the psychologist Maslow put forward a pyramid model to describe layers of human needs. It is indicated that the pyramid principle is universally applicable in natural, humanistic and social disciplines. Here, we report that a pyramid structure also exists in urban public health (UPH. Based on 18 indicators, the UPH states of four cities (Beijing, Tokyo, New York, and London are compared from the point of view of five aspects, namely physical health, living conditions, social security, environmental quality, and education and culture. A pyramid structure was found in each city when focusing on 2000–2009 data. The pyramid of Beijing is relatively similar to that of Tokyo, and the pyramids of New York and London are similar to each other. A general development trend in UPH is proposed and represented by different pyramid modes. As a basic conjecture, the UPH pyramid model can be verified and developed with data of more cities over a longer period, and be used to promote healthy urban development.

  13. Band Structure Characteristics of Nacreous Composite Materials with Various Defects

    Science.gov (United States)

    Yin, J.; Zhang, S.; Zhang, H. W.; Chen, B. S.

    2016-06-01

    Nacreous composite materials have excellent mechanical properties, such as high strength, high toughness, and wide phononic band gap. In order to research band structure characteristics of nacreous composite materials with various defects, supercell models with the Brick-and-Mortar microstructure are considered. An efficient multi-level substructure algorithm is employed to discuss the band structure. Furthermore, two common systems with point and line defects and varied material parameters are discussed. In addition, band structures concerning straight and deflected crack defects are calculated by changing the shear modulus of the mortar. Finally, the sensitivity of band structures to the random material distribution is presented by considering different volume ratios of the brick. The results reveal that the first band gap of a nacreous composite material is insensitive to defects under certain conditions. It will be of great value to the design and synthesis of new nacreous composite materials for better dynamic properties.

  14. Cellular structure formed by ion-implantation-induced point defect

    International Nuclear Information System (INIS)

    Nitta, N.; Taniwaki, M.; Hayashi, Y.; Yoshiie, T.

    2006-01-01

    The authors have found that a cellular defect structure is formed on the surface of Sn + ion implanted GaSb at a low temperature and proposed its formation mechanism based on the movement of the induced point defects. This research was carried out in order to examine the validity of the mechanism by clarifying the effect of the mobility of the point defects on the defect formation. The defect structure on the GaSb surfaces implanted at cryogenic temperature and room temperature was investigated by scanning electron microscopy (SEM) and cross-sectional transmission electron microscopy (TEM) observation. In the sample implanted at room temperature, the sponge-like structure (a pileup of voids) was formed and the cellular structure, as observed at a low temperature, did not develop. This behavior was explained by the high mobility of the vacancies during implantation at room temperature, and the proposed idea that the defect formation process is dominated by the induced point defects was confirmed

  15. Graphene materials having randomly distributed two-dimensional structural defects

    Science.gov (United States)

    Kung, Harold H; Zhao, Xin; Hayner, Cary M; Kung, Mayfair C

    2013-10-08

    Graphene-based storage materials for high-power battery applications are provided. The storage materials are composed of vertical stacks of graphene sheets and have reduced resistance for Li ion transport. This reduced resistance is achieved by incorporating a random distribution of structural defects into the stacked graphene sheets, whereby the structural defects facilitate the diffusion of Li ions into the interior of the storage materials.

  16. L-alanine distribution in the growth pyramids of TGS crystals and its influence on the growth, switching and domain structure

    International Nuclear Information System (INIS)

    Brezina, B.; Havrankova, M.

    1985-01-01

    The full-faced crystals of triglycine sulphate (TGS) and deuterated homologs substituted by L-alanine (LATGS and LADTGS, resp.) were grown from growth solutions with various concentrations of the substituent. The distribution of L, alanine (L,al) in various growth pyramids of crystals was measured by the electrical switching method. The stability of domain structure of doped crystals was studied by the liquid crystal method. (author)

  17. Extracting and identifying concrete structural defects in GPR images

    Science.gov (United States)

    Ye, Qiling; Jiao, Liangbao; Liu, Chuanxin; Cao, Xuehong; Huston, Dryver; Xia, Tian

    2018-03-01

    Traditionally most GPR data interpretations are performed manually. With the advancement of computing technologies, how to automate GPR data interpretation to achieve high efficiency and accuracy has become an active research subject. In this paper, analytical characterizations of major defects in concrete structures, including delamination, air void and moisture in GPR images, are performed. In the study, the image features of different defects are compared. Algorithms are developed for defect feature extraction and identification. For validations, both simulation results and field test data are utilized.

  18. Production defects in marine composite structures

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Christian; Tsouvalis, Nicholas G.

    2007-01-01

    Composite structures are often used when there is a requirement for low weight. Then a key aspect is to be able to take full advantage of the material and utilise it to its limits. To do this it is important to achieve as low a variability as possible in the manufacture of such structures...

  19. AUTOJOM, Quadratic Equation Coefficient for Conic Volume, Parallelepipeds, Wedges, Pyramids. JOMREAD, Check of 3-D Geometry Structure from Quadratic Surfaces

    International Nuclear Information System (INIS)

    2005-01-01

    Nature of physical problem solved: AUTOJOM is a computer program that will generate the coefficients of any quadratic equation used to define conic volumes and also the coefficients of the planes needed to define parallelepipeds, wedges, and pyramids. JOMREAD is a computer code to check any 3D geometry composed of and constructed with quadratic surfaces

  20. Electronic structure properties of deep defects in hBN

    Science.gov (United States)

    Dev, Pratibha; Prdm Collaboration

    In recent years, the search for room-temperature solid-state qubit (quantum bit) candidates has revived interest in the study of deep-defect centers in semiconductors. The charged NV-center in diamond is the best known amongst these defects. However, as a host material, diamond poses several challenges and so, increasingly, there is an interest in exploring deep defects in alternative semiconductors such as hBN. The layered structure of hBN makes it a scalable platform for quantum applications, as there is a greater potential for controlling the location of the deep defect in the 2D-matrix through careful experiments. Using density functional theory-based methods, we have studied the electronic and structural properties of several deep defects in hBN. Native defects within hBN layers are shown to have high spin ground states that should survive even at room temperature, making them interesting solid-state qubit candidates in a 2D matrix. Partnership for Reduced Dimensional Material (PRDM) is part of the NSF sponsored Partnerships for Research and Education in Materials (PREM).

  1. Transfer-matrix approach for modulated structures with defects

    International Nuclear Information System (INIS)

    Kostyrko, T.

    2000-01-01

    We consider scattering of electrons by defects in a periodically modulated, quasi-one-dimensional structure, within a tight-binding model. Combining a transfer matrix method and a Green function method we derive a formula for a Landauer conductance and show its equivalence to the result of Kubo linear response theory. We obtain explicitly unperturbed lattice Green functions from their equations of motion, using the transfer matrices. We apply the presented formalism in computations of the conductance of several multiband modulated structures with defects: (a) carbon nanotubes (b) two-dimensional (2D) superlattice (c) modulated leads with 1D wire in the tunneling regime. (c) 2000 The American Physical Society

  2. Thermoluminescence of pyramid stones

    International Nuclear Information System (INIS)

    Gomaa, M.A.; Eid, A.M.

    1982-01-01

    It is the aim of the present study to investigate some thermoluminescence properties of pyramid stones. Using a few grammes of pyramid stones from Pyramids I and II, the TL glow peaks were observed at 250 and 310 0 C, respectively. The TL glow peaks of samples annealed at 600 0 C, then exposed to 60 Co γ-rays were observed at 120, 190 and 310 0 C, respectively. The accumulated dose of natural samples is estimated to be around 310 Gray (31 krad). By assuming an annual dose is 1 mGy, the estimated age of pyramid stones is 0.31 M year. (author)

  3. Thermoluminescence of pyramid stones

    Energy Technology Data Exchange (ETDEWEB)

    Gomaa, M A; Eid, A M [Atomic Energy Establishment, Cairo (Egypt)

    1982-01-01

    It is the aim of the present study to investigate some thermoluminescence properties of pyramid stones. Using a few grammes of pyramid stones from Pyramids I and II, the TL glow peaks were observed at 250 and 310/sup 0/C, respectively. The TL glow peaks of samples annealed at 600/sup 0/C, then exposed to /sup 60/Co ..gamma..-rays were observed at 120, 190 and 310/sup 0/C, respectively. The accumulated dose of natural samples is estimated to be around 310 Gray (31 krad). By assuming an annual dose is 1 mGy, the estimated age of pyramid stones is 0.31 M year.

  4. Defects and defect generation in oxide layer of ion implanted silicon-silicon dioxide structures

    CERN Document Server

    Baraban, A P

    2002-01-01

    One studies mechanism of generation of defects in Si-SiO sub 2 structure oxide layer as a result of implantation of argon ions with 130 keV energy and 10 sup 1 sup 3 - 3.2 x 10 sup 1 sup 7 cm sup - sup 2 doses. Si-SiO sub 2 structures are produced by thermal oxidation of silicon under 950 deg C temperature. Investigations were based on electroluminescence technique and on measuring of high-frequency volt-farad characteristics. Increase of implantation dose was determined to result in spreading of luminosity centres and in its maximum shifting closer to boundary with silicon. Ion implantation was shown, as well, to result in increase of density of surface states at Si-SiO sub 2 interface. One proposed model of defect generation resulting from Ar ion implantation into Si-SiO sub 2

  5. Fracture Resistance, Surface Defects and Structural Strength of Glass

    NARCIS (Netherlands)

    Rodichev, Y.M.; Veer, F.A.

    2010-01-01

    This paper poses the theory that the fracture resistance of basic float glass is dependent on it physicochemical properties and the surface defects fonned under the float glass production, glass processing and handling at the service conditions compose the aggregate basis for structural glass

  6. Structure defects in malachite revealed by positron annihilation

    International Nuclear Information System (INIS)

    Geffroy, B.; Diallo, I.; Paulin, R.

    1984-01-01

    Positron lifetime is measured between 77 and 400 K in two malachite samples with different mineralogical structures. The complex spectrum found in zoned malachite reveals a microporosity which remains stable in this range of temperature. Besides, above 200 K, equilibrium defects appear. Their formation energy is estimated to be Esub(f) = 0.27 +- 0.02 eV [fr

  7. Structure defects in malachite revealed by positron annihilation

    Energy Technology Data Exchange (ETDEWEB)

    Geffroy, B; Diallo, I; Paulin, R [Institut National des Sciences et Techniques Nucleaires, CEN/Saclay, 91 - Gif-sur-Yvette (France)

    1984-01-01

    Positron lifetime is measured between 77 and 400 K in two malachite samples with different mineralogical structures. The complex spectrum found in zoned malachite reveals a microporosity which remains stable in this range of temperature. Besides, above 200 K, equilibrium defects appear. Their formation energy is estimated to be Esub(f) = 0.27 +- 0.02 eV.

  8. Influence of structural defects on excitonic photoluminescence of pentacene

    International Nuclear Information System (INIS)

    Piryatins'kij, Yu.P.; Kurik, M.V.

    2011-01-01

    The exciton reflection, absorption, and photoluminescence spectra for single crystals and polycrystalline films have been studied in the temperature range of 4.2-296 K. A significant influence of structural defects arising during phase transitions on the exciton spectra of pentacene has been detected. The mechanisms of photoluminescence in single crystals and crystalline films of pentacene have been considered.

  9. Effectively Improved Field Emission Properties of Multiwalled Carbon Nanotubes/Graphenes Composite Field Emitter by Covering on the Si Pyramidal Structure

    DEFF Research Database (Denmark)

    Chen, Leifeng; Yu, Hua; Zhong, Jiasong

    2015-01-01

    The composite nanostructure emitter of multiwalled carbon nanotubes and graphenes was deposited on pyramidal silicon substrate by the simple larger scale electrophoretic deposition process. The field emission (FE) properties of the composite/pyramidal Si device were greatly improved compared...

  10. Interactions of structural defects with metallic impurities in multicrystalline silicon

    International Nuclear Information System (INIS)

    McHugo, S.A.; Thompson, A.C.; Hieslmair, H.

    1997-01-01

    Multicrystalline silicon is one of the most promising materials for terrestrial solar cells. It is critical to getter impurities from the material as well as inhibit contamination during growth and processing. Standard processing steps such as, phosphorus in-diffusion for p-n junction formation and aluminum sintering for backside ohmic contact fabrication, intrinsically possess gettering capabilities. These processes have been shown to improve L n values in regions of multicrystalline silicon with low structural defect densities but not in highly dislocated regions. Recent Deep Level Transient Spectroscopy (DLTS) results indirectly reveal higher concentrations of iron in highly dislocated regions while further work suggests that the release of impurities from structural defects, such as dislocations, is the rate limiting step for gettering in multicrystalline silicon. The work presented here directly demonstrates the relationship between metal impurities, structural defects and solar cell performance in multicrystalline silicon. Edge-defined Film-fed Growth (EFG) multicrystalline silicon in the as-grown state and after full solar cell processing was used in this study. Standard solar cell processing steps were carried out at ASE Americas Inc. Metal impurity concentrations and distributions were determined by use of the x-ray fluorescence microprobe (beamline 10.3.1) at the Advanced Light Source, Lawrence Berkeley National Laboratory. The sample was at atmosphere so only elements with Z greater than silicon could be detected, which includes all metal impurities of interest. Structural defect densities were determined by preferential etching and surface analysis using a Scanning Electron Microscope (SEM) in secondary electron mode. Mapped areas were exactly relocated between the XRF and SEM to allow for direct comparison of impurity and structural defect distributions

  11. Diffusive, Structural, Optical, and Electrical Properties of Defects in Semiconductors

    CERN Multimedia

    Wagner, F E

    2002-01-01

    Electronic properties of semiconductors are extremely sensitive to defects and impurities that have localized electronic states with energy levels in the band gap of the semiconductor. Spectroscopic techniques like photoluminescence (PL), deep level transient spectroscopy (DLTS), or Hall effect, that are able to detect and characterize band gap states do not reveal direct information about their microscopic origin. To overcome this chemical "blindness", the present approach is to use radioactive isotopes as a tracer. Moreover, the recoil energies involved in $\\beta$ and $\\gamma$-decays can be used to create intrinsic isolated point defects (interstitials, vacancies) in a controlled way. A microscopic insight into the structure and the thermodynamic properties of complexes formed by interacting defects can be gained by detecting the hyperfine interaction between the nuclear moments of radioactive dopants and the electromagnetic fields present at the site of the radioactive nucleus. The understanding and the co...

  12. The Formation and Characterization of GaN Hexagonal Pyramids

    Science.gov (United States)

    Zhang, Shi-Ying; Xiu, Xiang-Qian; Lin, Zeng-Qin; Hua, Xue-Mei; Xie, Zi-Li; Zhang, Rong; Zheng, You-Dou

    2013-05-01

    GaN with hexagonal pyramids is fabricated using the photo-assisted electroless chemical etching method. Defective areas of the GaN substrate are selectively etched in a mixed solution of KOH and K2S2O8 under ultraviolet illumination, producing submicron-sized pyramids. Hexagonal pyramids on the etched GaN with well-defined {101¯1¯} facets and very sharp tips are formed. High-resolution x-ray diffraction shows that etched GaN with pyramids has a higher crystal quality, and micro-Raman spectra reveal a tensile stress relaxation in GaN with pyramids compared with normal GaN. The cathodoluminescence intensity of GaN after etching is significantly increased by three times, which is attributed to the reduction in the internal reflection, high-quality GaN with pyramids and the Bragg effect.

  13. Fracture Resistance, Surface Defects and Structural Strength of Glass

    OpenAIRE

    Rodichev, Y.M.; Veer, F.A.

    2010-01-01

    This paper poses the theory that the fracture resistance of basic float glass is dependent on it physicochemical properties and the surface defects fonned under the float glass production, glass processing and handling at the service conditions compose the aggregate basis for structural glass strength assessment. The effect of loading conditions, constructional and technological factors on the engineering strength of glass can be evaluated in certain cases using fracture mechanics with inform...

  14. Fine structure and analytical quantum-defect wave functions

    International Nuclear Information System (INIS)

    Kostelecky, V.A.; Nieto, M.M.; Truax, D.R.

    1988-01-01

    We investigate the domain of validity of previously proposed analytical wave functions for atomic quantum-defect theory. This is done by considering the fine-structure splitting of alkali-metal and singly ionized alkaline-earth atoms. The Lande formula is found to be naturally incorporated. A supersymmetric-type integer is necessary for finite results. Calculated splittings correctly reproduce the principal features of experimental values for alkali-like atoms

  15. Defect-induced magnetic structure of CuMnSb

    Czech Academy of Sciences Publication Activity Database

    Máca, František; Kudrnovský, Josef; Drchal, Václav; Turek, I.; Stelmakhovych, O.; Beran, Přemysl; Llobet, A.; Martí, Xavier

    2016-01-01

    Roč. 94, č. 9 (2016), 1-9, č. článku 094407. ISSN 2469-9950 R&D Projects: GA ČR GB14-37427G Institutional support: RVO:68378271 ; RVO:61389005 Keywords : CuMnSb * electronic structure * defects * magnetic order * ab initio calculations * neutron diffraction analysis Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.836, year: 2016

  16. Probing defect and magnetic structures on the nanoscale

    OpenAIRE

    Kallis, Alexis

    2010-01-01

    This thesis reports on experimental research on structural defects and magnetic species on the nanoscale. The latter project involved considerable development work on the production of a spin-polarised mono-energetic positron beam. The construction of the system is described through various trial steps with emphasis on the methods of maximum practical polarization of the positron beam and of electrons in the sample with the smallest possible loss of beam intensity. A new sodium-22 source caps...

  17. The defect structure of ceramic high Tc superconductors

    International Nuclear Information System (INIS)

    Van Tendeloo, G.; Amelinckx, S.; Zandbergen, H.W.; Verwerft, M.

    1989-01-01

    In this paper an overview is given of electron microscopy studies on the different ceramic superconductors: YBa 2 Cu 3 O 7 , Bi(Tl)-Sr(Ba)- Ca-Cu-O and Pb 2 Sr 2 Y 0.5 Ca 0.5 Cu 3 O x . Planar defects in these materials play an important role in the superconducting properties. Their structural characteristics are discussed

  18. Structural defects in electrodeposited Ni studied by positron annihilation

    International Nuclear Information System (INIS)

    Vertes, A.; Szeles, C.; Czako-Nagy, I.; Lakatos-Varsanyi, M.

    1982-01-01

    Structural investigation of electrodeposited Ni was carried out by positron annihilation (PA) technique. Additional Moessbauer effect and X-ray diffraction measurements were also performed. The samples were produced under different plating conditions resulting in stress in the range -100 to +600 N/mm 2 . From the positron lifetime measurements it seems that the defect pattern of electrodeposited Ni samples might be substantially different from sample to sample with different deposition and plating conditions. (Auth.)

  19. Characterization of the structure and chemistry of defects in materials

    International Nuclear Information System (INIS)

    Larson, B.C.; Ruehle, M.; Seidman, D.N.

    1988-01-01

    Research programs, presented at the materials research symposium, on defects in materials are presented. Major areas include: point defects, defect aggregates, and ordering; defects in non-metals and semiconductors; atomic resolution imaging of defects; and gain boundaries, interfaces, and layered materials. Individual projects are processed separately for the data bases

  20. Understanding the defect structure of solution grown zinc oxide

    Energy Technology Data Exchange (ETDEWEB)

    Liew, Laura-Lynn [Institute of Materials Research and Engineering, Agency for Science, Technology and Research (A-STAR), 3 Research Link, Singapore 117602 (Singapore); School of Materials Science and Engineering, Nanyang Technological University, Block N4.1 Nanyang Avenue, Singapore 639798 (Singapore); Sankar, Gopinathan, E-mail: g.sankar@ucl.ac.uk [Department of Chemistry, University College London, 20 Gordon Street, London WC1H 0AJ (United Kingdom); Handoko, Albertus D. [Institute of Materials Research and Engineering, Agency for Science, Technology and Research (A-STAR), 3 Research Link, Singapore 117602 (Singapore); Goh, Gregory K.L., E-mail: g-goh@imre.a-star.edu.sg [Institute of Materials Research and Engineering, Agency for Science, Technology and Research (A-STAR), 3 Research Link, Singapore 117602 (Singapore); School of Materials Science and Engineering, Nanyang Technological University, Block N4.1 Nanyang Avenue, Singapore 639798 (Singapore); Kohara, Shinji [Japan Synchrotron Radiation Research Institute (JASRI), Mikazuki, Sayo, Hyogo 679-5198 (Japan)

    2012-05-15

    Zinc oxide (ZnO) is a wide bandgap semiconducting oxide with many potential applications in various optoelectronic devices such as light emitting diodes (LEDs) and field effect transistors (FETs). Much effort has been made to understand the ZnO structure and its defects. However, one major issue in determining whether it is Zn or O deficiency that provides ZnO its unique properties remains. X-ray absorption spectroscopy (XAS) is an ideal, atom specific characterization technique that is able to probe defect structure in many materials, including ZnO. In this paper, comparative studies of bulk and aqueous solution grown ({<=}90 Degree-Sign C) ZnO powders using XAS and x-ray pair distribution function (XPDF) techniques are described. The XAS Zn-Zn correlation and XPDF results undoubtedly point out that the solution grown ZnO contains Zn deficiency, rather than the O deficiency that were commonly reported. This understanding of ZnO short range order and structure will be invaluable for further development of solid state lighting and other optoelectronic device applications. - Graphical abstract: Highlights: Black-Right-Pointing-Pointer ZnO powders have been synthesized through an aqueous solution method. Black-Right-Pointing-Pointer Defect structure studied using XAS and XPDF. Black-Right-Pointing-Pointer Zn-Zn correlations are less in the ZnO powders synthesized in solution than bulk. Black-Right-Pointing-Pointer Zn vacancies are present in the powders synthesized. Black-Right-Pointing-Pointer EXAFS and XPDF, when used complementary, are useful characterization techniques.

  1. Structural defects in laser- and electron-beam annealed silicon

    International Nuclear Information System (INIS)

    Narayan, J.

    1979-01-01

    Laser and electron beam pulses provide almost an ideal source of heat by which thin layers of semiconductors can be rapidly melted and solidified with heating and cooling rates exceeding 10 80 C/sec. Microstructural modifications obtained as a function of laser parameters are examined and it is shown that both laser and electron beam pulses can be used to remove displacement damage, dislocations, dislocation loops and precipitates. Annealing of defects underneath the oxide layers in silicon is possible within a narrow energy window. The formation of cellular structure provides a rather clear evidence of melting which leads to segregation and supercooling, and subsequent cell formation

  2. High-performance SERS substrate based on hybrid structure of graphene oxide/AgNPs/Cu film@pyramid Si

    Science.gov (United States)

    Li, Zhe; Xu, Shi Cai; Zhang, Chao; Liu, Xiao Yun; Gao, Sai Sai; Hu, Li Tao; Guo, Jia; Ma, Yong; Jiang, Shou Zhen; Si, Hai Peng

    2016-12-01

    We present a novel surface-enhanced Raman scattering (SERS) substrate based on graphene oxide/silver nanoparticles/copper film covered silicon pyramid arrays (GO/AgNPs/PCu@Si) by a low-cost and simple method. The GO/AgNPs/PCu@Si substrate presents high sensitivity, good homogeneity and well stability with R6G molecules as a probe. The detected concentration of Rhodamine 6 G (R6G) is as low as 10-15 M. These sensitive SERS behaviors are also confirmed in theory via a commercial COMSOL software, the electric field enhancement is not only formed between the AgNPs, but also formed between the AgNPs and Cu film. And the GO/AgNPs/PCu@Si substrates also present good property on practical application for the detection of methylene blue (MB) and crystal violet (CV). This work may offer a novel and practical method to facilitate the SERS applications in areas of medicine, food safety and biotechnology.

  3. Dynamic interaction of two-phase debris flow with pyramidal defense structures: An optimal strategy to efficiently protecting the desired area

    Science.gov (United States)

    Kattel, Parameshwari; Kafle, Jeevan; Fischer, Jan-Thomas; Mergili, Martin; Tuladhar, Bhadra Man; Pudasaini, Shiva P.

    2017-04-01

    In this work we analyze the dynamic interaction of two phase debris flows with pyramidal obstacles. To simulate the dynamic interaction of two-phase debris flow (a mixture of solid particles and viscous fluid) with obstacles of different dimensions and orientations, we employ the general two-phase mass flow model (Pudasaini, 2012). The model consists of highly non-linear partial differential equations representing the mass and momentum conservations for both solid and fluid. Besides buoyancy, the model includes some dominant physical aspects of the debris flows such as generalized drag, virtual mass and non-Newtonian viscous stress as induced by the gradient of solid-volume-fraction. Simulations are performed with high-resolution numerical schemes to capture essential dynamics, including the strongly re-directed flow with multiple stream lines, mass arrest and debris-vacuum generation when the rapidly cascading debris mass suddenly encounters the obstacle. The solid and fluid phases show fundamentally different interactions with obstacles, flow spreading and dispersions, run-out dynamics, and deposition morphology. A forward-facing pyramid deflects the mass wider, and a rearward-facing pyramid arrests a portion of solid-mass at its front. Our basic study reveals that appropriately installed obstacles, their dimensions and orientations have a significant influence on the flow dynamics, material redistribution and redirection. The precise knowledge of the change in dynamics is of great importance for the optimal and effective protection of designated areas along the mountain slopes and the runout zones. Further important results are, that specific installations lead to redirect either solid, or fluid, or both, in the desired amounts and directions. The present method of the complex interactions of real two-phase mass flows with the obstacles may help us to construct defense structures and to design advanced and physics-based engineering solutions for the prevention

  4. AACSD: An atomistic analyzer for crystal structure and defects

    Science.gov (United States)

    Liu, Z. R.; Zhang, R. F.

    2018-01-01

    We have developed an efficient command-line program named AACSD (Atomistic Analyzer for Crystal Structure and Defects) for the post-analysis of atomic configurations generated by various atomistic simulation codes. The program has implemented not only the traditional filter methods like the excess potential energy (EPE), the centrosymmetry parameter (CSP), the common neighbor analysis (CNA), the common neighborhood parameter (CNP), the bond angle analysis (BAA), and the neighbor distance analysis (NDA), but also the newly developed ones including the modified centrosymmetry parameter (m-CSP), the orientation imaging map (OIM) and the local crystallographic orientation (LCO). The newly proposed OIM and LCO methods have been extended for all three crystal structures including face centered cubic, body centered cubic and hexagonal close packed. More specially, AACSD can be easily used for the atomistic analysis of metallic nanocomposite with each phase to be analyzed independently, which provides a unique pathway to capture their dynamic evolution of various defects on the fly. In this paper, we provide not only a throughout overview on various theoretical methods and their implementation into AACSD program, but some critical evaluations, specific testing and applications, demonstrating the capability of the program on each functionality.

  5. Climbing the Needs Pyramids

    Directory of Open Access Journals (Sweden)

    J. C. Lomas

    2013-08-01

    Full Text Available Abraham Maslow’s theory of human adult motivation is often represented by a pyramid image showing two proposals: First, the five needs stages in emergent order of hierarchical ascension and second, a percentage of the adult population suggested to occupy each needs tier. Specifically, Maslow proposed that adults would be motivated to satisfy their unfilled needs until they reached the hierarchy’s apex and achieved self-transcendence. Yet how adults can purposefully ascend Maslow’s pyramid through satisfying unfilled needs remains elusive. This brief article challenges this on the theory’s 70th anniversary by presenting a new image of the needs hierarchy, based on ecological design principles to support adults’ purposeful endeavors to climb the needs pyramid.

  6. Double-bond defect modelling in As-S glasses

    International Nuclear Information System (INIS)

    Boyko, V; Shpotyuk, O; Hyla, M

    2010-01-01

    Ab initio calculations with the RHF/6-311G* basis set are used for geometrical optimization of regular pyramidal and defect quasi-tetrahedral clusters in binary As-S glasses. It is shown that quasi-tetrahedral S=AsS 3/2 structural units are impossible as main network-building blocks in these glasses.

  7. Double-bond defect modelling in As-S glasses

    Energy Technology Data Exchange (ETDEWEB)

    Boyko, V; Shpotyuk, O; Hyla, M, E-mail: shpotyuk@novas.lviv.ua

    2010-11-15

    Ab initio calculations with the RHF/6-311G* basis set are used for geometrical optimization of regular pyramidal and defect quasi-tetrahedral clusters in binary As-S glasses. It is shown that quasi-tetrahedral S=AsS{sub 3/2} structural units are impossible as main network-building blocks in these glasses.

  8. Dislocations and related defects in niobium oxide structures

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J S; Hutchinson, J L; Lincoln, F J [Oxford Univ. (UK). Inorganic Chemistry Lab.

    1977-01-07

    Lattice images of the niobium oxides, structures based on the linkage of octahedral groups in continuous networks, occasionally contain features recognizable as dislocations. Since lattice imaging enables the microstructure to be resolved in greater detail, at the level of local structural organization, it is possible to determine the configuration, and also to infer the chemical composition, of dislocated areas. By treating the niobium oxide 'block' structures as superstructures of the ReO/sub 3/ (DO/sub 9/) type, the topology of dislocations can be expressed by relations between the insertion (or deletion) of one or more half-planes of cations, or of oxygen atoms only, changes in the number of crystallographic shear plane interfaces between blocks or columns, changes in (idealized) dimensions and any requisite distortion in the third dimension. Mapping the structure around a dislocation, from the lattice image, is directly equivalent to plotting the Burgers' circuit. In this way, the precise nature of a dislocating perturbation and its implications for the local chemical composition of the crystal can be directly identified. The method is exemplified by analysis of dislocations and of related extended defects of several types, associated with twinning phenomena, semicoherent intergrowth between different ReO/sub 3/-type superstructures and arrays building up a low angle boundary. The essential features of the analysis are not restricted to structures of the niobium oxide type, but can be extended to other types of polyhedron networks.

  9. Modification of electronic structure, magnetic structure, and topological phase of bismuthene by point defects

    Science.gov (United States)

    Kadioglu, Yelda; Kilic, Sevket Berkay; Demirci, Salih; Aktürk, O. Üzengi; Aktürk, Ethem; Ciraci, Salim

    2017-12-01

    This paper reveals how the electronic structure, magnetic structure, and topological phase of two-dimensional (2D), single-layer structures of bismuth are modified by point defects. We first showed that a free-standing, single-layer, hexagonal structure of bismuth, named h-bismuthene, exhibits nontrivial band topology. We then investigated interactions between single foreign adatoms and bismuthene structures, which comprise stability, bonding, electronic structure, and magnetic structures. Localized states in diverse locations of the band gap and resonant states in band continua of bismuthene are induced upon the adsorption of different adatoms, which modify electronic and magnetic properties. Specific adatoms result in reconstruction around the adsorption site. Single vacancies and divacancies can form readily in bismuthene structures and remain stable at high temperatures. Through rebondings, Stone-Whales-type defects are constructed by divacancies, which transform into a large hole at high temperature. Like adsorbed adatoms, vacancies induce also localized gap states, which can be eliminated through rebondings in divacancies. We also showed that not only the optical and magnetic properties, but also the topological features of pristine h-bismuthene can be modified by point defects. The modification of the topological features depends on the energies of localized states and also on the strength of coupling between point defects.

  10. Defect structure of ultrafine MgB2 nanoparticles

    International Nuclear Information System (INIS)

    Bateni, Ali; Somer, Mehmet; Repp, Sergej; Erdem, Emre; Thomann, Ralf; Acar, Selçuk

    2014-01-01

    Defect structure of MgB 2 bulk and ultrafine particles, synthesized by solid state reaction route, have been investigated mainly by the aid of X-band electron paramagnetic resonance spectrometer. Two different amorphous Boron (B) precursors were used for the synthesis of MgB 2 , namely, boron 95 (purity 95%–97%, <1.5 μm) and nanoboron (purity >98.5%, <250 nm), which revealed bulk and nanosized MgB 2 , respectively. Scanning and transmission electron microscopy analysis demonstrate uniform and ultrafine morphology for nanosized MgB 2 in comparison with bulk MgB 2 . Powder X-ray diffraction data show that the concentration of the by-product MgO is significantly reduced when nanoboron is employed as precursor. It is observed that a significant average particle size reduction for MgB 2 can be achieved only by using B particles of micron or nano size. The origin and the role of defect centers were also investigated and the results proved that at nanoscale MgB 2 material contains Mg vacancies. Such vacancies influence the connectivity and the conductivity properties which are crucial for the superconductivity applications

  11. Pyramid Comet Sampler, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Based on the sampling requirements, we propose an Inverted Pyramid sampling system. Each face of the pyramid includes a cutting blade which is independently actuated...

  12. David Macaulay's Pyramid.

    Science.gov (United States)

    Frew, Andrew W.

    1997-01-01

    Integrating literature and mathematics can be meaningful using David Macaulay's "Pyramid." This article provides an annotated bibliography of picture books, fiction, folk tales, nonfiction, videotapes, audio books, and CD-ROMs for grades 1-12 to support a unit on Egypt. Describes related math activities; and highlights a catalog of…

  13. Atomistic simulations of divacancy defects in armchair graphene nanoribbons: Stability, electronic structure, and electron transport properties

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jun [College of Physical Science and Technology, Yangtze University, Jingzhou, Hubei 434023 (China); Zeng, Hui, E-mail: zenghui@yangtzeu.edu.cn [College of Physical Science and Technology, Yangtze University, Jingzhou, Hubei 434023 (China); Wei, Jianwei [College of Optoelectronic Information, Chongqing University of Technology, Chongqing 400054 (China); Li, Biao; Xu, Dahai [College of Physical Science and Technology, Yangtze University, Jingzhou, Hubei 434023 (China)

    2014-01-17

    Using the first principles calculations associated with nonequilibrium Green's function, we have studied the electronic structures and quantum transport properties of defective armchair graphene nanoribbon (AGNR) in the presence of divacancy defects. The triple pentagon–triple heptagon (555–777) defect in the defective AGNR is energetically more favorable than the pentagon–octagon–pentagon (5–8–5) defect. Our calculated results reveal that both 5–8–5-like defect and 555–777-like defect in AGNR could improve the electron transport. It is anticipated that defective AGNRs can exhibit large range variations in transport behaviors, which are strongly dependent on the distributions of the divacancy defect.

  14. Tunneling and propping : A justification for pyramidal ownership

    NARCIS (Netherlands)

    Riyanto, Y.E.; Toolsema-Veldman, Linda

    2008-01-01

    This paper links existence of the pyramidal ownership structure to tunneling and propping. Tunneling refers to a transfer of resources from a lower-level firm to a higher-level firm in the pyramidal chain, whereas propping concerns a transfer in the opposite direction intended to bail out the

  15. Tunneling and propping : a justification for pyramidal ownership

    NARCIS (Netherlands)

    Riyanto, Y.E.; Toolsema-Veldman, Linda

    2004-01-01

    This paper presents a formal model of tunneling and propping in a pyramidal ownership structure. Tunneling refers to controlling shareholders shifting resources from one firm to another in the same pyramid. Propping is tunneling that is done to save the receiving firm from bankruptcy. We compare the

  16. A comparative study on defect estimation using XPS and Raman spectroscopy in few layer nanographitic structures.

    Science.gov (United States)

    Ganesan, K; Ghosh, Subrata; Gopala Krishna, Nanda; Ilango, S; Kamruddin, M; Tyagi, A K

    2016-08-10

    Defects in planar and vertically oriented nanographitic structures (NGSs) synthesized by plasma enhanced chemical vapor deposition (PECVD) have been investigated using Raman and X-ray photoelectron spectroscopy. While Raman spectra reveal the dominance of vacancy and boundary type defects respectively in vertical and planar NGSs, XPS provides additional information on vacancy related defect peaks in the C 1s spectrum, which originate from non-conjugated carbon atoms in the hexagonal lattice. Although an excellent correlation prevails between these two techniques, our results show that estimation of surface defects by XPS is more accurate than Raman analysis. Nuances of these techniques are discussed in the context of assessing defects in nanographitic structures.

  17. Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling.

    Directory of Open Access Journals (Sweden)

    Evgeniy G Gordeev

    Full Text Available Additive manufacturing with fused deposition modeling (FDM is currently optimized for a wide range of research and commercial applications. The major disadvantage of FDM-created products is their low quality and structural defects (porosity, which impose an obstacle to utilizing them in functional prototyping and direct digital manufacturing of objects intended to contact with gases and liquids. This article describes a simple and efficient approach for assessing the quality of 3D printed objects. Using this approach it was shown that the wall permeability of a printed object depends on its geometric shape and is gradually reduced in a following series: cylinder > cube > pyramid > sphere > cone. Filament feed rate, wall geometry and G-code-defined wall structure were found as primary parameters that influence the quality of 3D-printed products. Optimization of these parameters led to an overall increase in quality and improvement of sealing properties. It was demonstrated that high quality of 3D printed objects can be achieved using routinely available printers and standard filaments.

  18. Fracture mechanical evaluation of high temperature structure and creep-fatigue defect assessment

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Gyu; Kim, Jong Bum; Lee, Jae Han

    2004-02-01

    This study proposed the evaluation procedure of high temperature structures from the viewpoint of fracture mechanics on the cylindrical structure applicable to the KALIMER, which is developed by KAERI. For the evaluation of structural integrity, linear and non-linear fracture mechanics parameters were analyzed. Parameters used in creep defect growth applicable to high temperature structure of liquid metal reactor and the evaluation codes with these parameters were analyzed. The evaluation methods of defect initiation and defect growth which were established in R5/R6 code(UK), JNC method (Japan) and RCC-MR A16(France) code were analyzed respectively. The evaluation procedure of leak before break applicable to KALIMER was preliminarily developed and proposed. As an application example of defect growth, the creep-fatigue defect growth on circumferential throughwall defect in high temperature cylindrical structure was evaluated by RCC-MR A16 and this application technology was established.

  19. Climbing the Needs Pyramids

    OpenAIRE

    J. C. Lomas

    2013-01-01

    Abraham Maslow’s theory of human adult motivation is often represented by a pyramid image showing two proposals: First, the five needs stages in emergent order of hierarchical ascension and second, a percentage of the adult population suggested to occupy each needs tier. Specifically, Maslow proposed that adults would be motivated to satisfy their unfilled needs until they reached the hierarchy’s apex and achieved self...

  20. Structural defects in monocrystalline silicon: from radiation ones to growing and technological

    International Nuclear Information System (INIS)

    Gerasimenko, N.N.; Pavlyuchenko, M.N.; Dzhamanbalin, K.K.

    2001-01-01

    The systematical review of properties and conditions of radiation structures in monocrystalline silicon including own defects (elementary and complex, disordered fields) as well as defect-impurity formations is presented. The most typical examples of principle effects influence of known defects on radiation-induced processes (phase transformations, diffusion and heteration and others are considered. Experimental facts and models of silicon radiation amorphization have been analyzed in comparison of state of the radiation amorphization radiation problem of metals and alloys. The up-to-date status of the problem of the radiation defects physics are discussed, including end-of-range -, n+-, rod-like- defects. The phenomenon self-organization in crystals with defects has been considered. The examples of directed using radiation defects merged in independent trend - defects engineering - are given

  1. Subsurface defects structural evolution in nano-cutting of single crystal copper

    International Nuclear Information System (INIS)

    Wang, Quanlong; Bai, Qingshun; Chen, Jiaxuan; Sun, Yazhou; Guo, Yongbo; Liang, Yingchun

    2015-01-01

    Highlights: • An innovative analysis method is adopted to analyze nano-cutting process accurately. • A characteristic SFT and stair-rod dislocation are found in subsurface defect layer. • The formation mechanism of stair-rod dislocation is investigated. • The local atomic structure of subsurface defects is introduced. - Abstract: In this work, molecular dynamics simulation is performed to study the subsurface defects structural distribution and its evolution during nano-cutting process of single crystal copper. The formation mechanism of chip and machined surface is interviewed by analyzing the dislocation evolution and atomic migration. The centro-symmetry parameter and spherical harmonics method are adopted to characterize the distribution and evolution of the subsurface defect structures and local atomic structures. The results show that stacking faults, dislocation loops, “V-shaped” dislocation loops, and plenty of point defects are formed during the machined surface being formed in shear-slip zone. In subsurface damage layers, stair-rod dislocation, stacking fault tetrahedra, atomic cluster defect, and vacancy defect are formed. And the formation mechanism of stair-rod dislocation is investigated by atomic-scale structure evolution. The local atomic structures of subsurface defects are icosahedrons, hexagonal close packed, body-centered cubic, and defect face center cubic, and the variations of local atomic structures are investigated

  2. Subsurface defects structural evolution in nano-cutting of single crystal copper

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Quanlong [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Center for Precision Engineering, Harbin Institute of Technology, Harbin 150001 (China); Bai, Qingshun [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Chen, Jiaxuan, E-mail: wangquanlong0@hit.edu.cn [Center for Precision Engineering, Harbin Institute of Technology, Harbin 150001 (China); Sun, Yazhou [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China); Guo, Yongbo [Center for Precision Engineering, Harbin Institute of Technology, Harbin 150001 (China); Liang, Yingchun [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China)

    2015-07-30

    Highlights: • An innovative analysis method is adopted to analyze nano-cutting process accurately. • A characteristic SFT and stair-rod dislocation are found in subsurface defect layer. • The formation mechanism of stair-rod dislocation is investigated. • The local atomic structure of subsurface defects is introduced. - Abstract: In this work, molecular dynamics simulation is performed to study the subsurface defects structural distribution and its evolution during nano-cutting process of single crystal copper. The formation mechanism of chip and machined surface is interviewed by analyzing the dislocation evolution and atomic migration. The centro-symmetry parameter and spherical harmonics method are adopted to characterize the distribution and evolution of the subsurface defect structures and local atomic structures. The results show that stacking faults, dislocation loops, “V-shaped” dislocation loops, and plenty of point defects are formed during the machined surface being formed in shear-slip zone. In subsurface damage layers, stair-rod dislocation, stacking fault tetrahedra, atomic cluster defect, and vacancy defect are formed. And the formation mechanism of stair-rod dislocation is investigated by atomic-scale structure evolution. The local atomic structures of subsurface defects are icosahedrons, hexagonal close packed, body-centered cubic, and defect face center cubic, and the variations of local atomic structures are investigated.

  3. A New Defected Ground Structure for Different Microstrip Circuit Applications

    Directory of Open Access Journals (Sweden)

    S. Das

    2007-04-01

    Full Text Available In this paper, a microstrip transmission line combined with a new U-headed dumb-bell defected ground structure (DGS is investigated. The proposed DGS of two U-shape slots connected by a thin transverse slot is placed in the ground plane of a microstrip line. A finite cutoff frequency and attenuation pole is observed and thus, the equivalent circuit of the DGS unit can be represented by a parallel LC resonant circuit in series with the transmission line. A two-cell DGS microstrip line yields a better lowpass filtering characteristics. The simulation is carried out by the MoM based IE3D software and in the experimental measurements a vector network analyzer is used. The effects of the transverse slot width and the distance between arms of the U-slot on the filter response curve are studied. This DGS is utilized for different microstrip circuit applications. The DGS is placed in the ground of a capacitive loaded microstrip line and a very low cutoff frequency is obtained. The DGS is adopted under the coupled lines of a parallel line coupler and an improvement in coupling coefficient is noticed. The proposed DGS is also incorporated in the ground plane under the feed lines and the coupled lines of a bandpass filter to improve separately the stopband and passband performances.

  4. Virtual Reality Tumor Resection: The Force Pyramid Approach.

    Science.gov (United States)

    Sawaya, Robin; Bugdadi, Abdulgadir; Azarnoush, Hamed; Winkler-Schwartz, Alexander; Alotaibi, Fahad E; Bajunaid, Khalid; AlZhrani, Gmaan A; Alsideiri, Ghusn; Sabbagh, Abdulrahman J; Del Maestro, Rolando F

    2017-09-05

    The force pyramid is a novel visual representation allowing spatial delineation of instrument force application during surgical procedures. In this study, the force pyramid concept is employed to create and quantify dominant hand, nondominant hand, and bimanual force pyramids during resection of virtual reality brain tumors. To address 4 questions: Do ergonomics and handedness influence force pyramid structure? What are the differences between dominant and nondominant force pyramids? What is the spatial distribution of forces applied in specific tumor quadrants? What differentiates "expert" and "novice" groups regarding their force pyramids? Using a simulated aspirator in the dominant hand and a simulated sucker in the nondominant hand, 6 neurosurgeons and 14 residents resected 8 different tumors using the CAE NeuroVR virtual reality neurosurgical simulation platform (CAE Healthcare, Montréal, Québec and the National Research Council Canada, Boucherville, Québec). Position and force data were used to create force pyramids and quantify tumor quadrant force distribution. Force distribution quantification demonstrates the critical role that handedness and ergonomics play on psychomotor performance during simulated brain tumor resections. Neurosurgeons concentrate their dominant hand forces in a defined crescent in the lower right tumor quadrant. Nondominant force pyramids showed a central peak force application in all groups. Bimanual force pyramids outlined the combined impact of each hand. Distinct force pyramid patterns were seen when tumor stiffness, border complexity, and color were altered. Force pyramids allow delineation of specific tumor regions requiring greater psychomotor ability to resect. This information can focus and improve resident technical skills training. Copyright © 2017 by the Congress of Neurological Surgeons

  5. Related Structure Characters and Stability of Structural Defects in a Metallic Glass.

    Science.gov (United States)

    Niu, Xiaofeng; Feng, Shidong; Pan, Shaopeng

    2018-03-22

    Structural defects were investigated by a recently proposed structural parameter, quasi-nearest atom (QNA), in a modeled Zr 50 Cu 50 metallic glass through molecular dynamics simulations. More QNAs around an atom usually means that more defects are located near the atom. Structural analysis reveals that the spatial distribution of the numbers of QNAs displays to be clearly heterogeneous. Furthermore, QNA is closely correlated with cluster connections, especially four-atom cluster connections. Atoms with larger coordination numbers usually have less QNAs. When two atoms have the same coordination number, the atom with larger five-fold symmetry has less QNAs. The number of QNAs around an atom changes rather frequently and the change of QNAs might be correlated with the fast relaxation metallic glasses.

  6. Related Structure Characters and Stability of Structural Defects in a Metallic Glass

    Science.gov (United States)

    Niu, Xiaofeng; Feng, Shidong; Pan, Shaopeng

    2018-01-01

    Structural defects were investigated by a recently proposed structural parameter, quasi-nearest atom (QNA), in a modeled Zr50Cu50 metallic glass through molecular dynamics simulations. More QNAs around an atom usually means that more defects are located near the atom. Structural analysis reveals that the spatial distribution of the numbers of QNAs displays to be clearly heterogeneous. Furthermore, QNA is closely correlated with cluster connections, especially four-atom cluster connections. Atoms with larger coordination numbers usually have less QNAs. When two atoms have the same coordination number, the atom with larger five-fold symmetry has less QNAs. The number of QNAs around an atom changes rather frequently and the change of QNAs might be correlated with the fast relaxation metallic glasses. PMID:29565298

  7. Application of Ultrasonic Phased Array Technology to the Detection of Defect in Composite Stiffened-structures

    Science.gov (United States)

    Zhou, Yuan-Qi; Zhan, Li-Hua

    2016-05-01

    Composite stiffened-structure consists of the skin and stringer has been widely used in aircraft fuselage and wings. The main purpose of the article is to detect the composite material reinforced structure accurately and explore the relationship between defect formation and structural elements or curing process. Based on ultrasonic phased array inspection technology, the regularity of defects in the manufacture of composite materials are obtained, the correlation model between actual defects and nondestructive testing are established. The article find that the forming quality of deltoid area in T-stiffened structure is obviously improved by pre-curing, the defects of hat-stiffened structure are affected by the mandrel. The results show that the ultrasonic phased array inspection technology can be an effectively way for the detection of composite stiffened-structures, which become an important means to control the defects of composite and improve the quality of the product.

  8. Growth, defect structure, and THz application of stoichiometric lithium niobate

    Energy Technology Data Exchange (ETDEWEB)

    Lengyel, K.; Péter, Á.; Kovács, L.; Corradi, G.; Dravecz, G.; Hajdara, I.; Szaller, Zs.; Polgár, K. [Wigner Research Centre for Physics, Hungarian Academy of Sciences, 1121 Budapest, Konkoly-Thege M. út 29-33 (Hungary); Pálfalvi, L.; Unferdorben, M. [Institute of Physics, University of Pécs, 7624 Pécs, Ifjúság útja 6 (Hungary); Hebling, J. [Institute of Physics, University of Pécs, 7624 Pécs, Ifjúság útja 6 (Hungary); MTA-PTE High Field Terahertz Research Group, 7624 Pécs (Hungary)

    2015-12-15

    preferred for most nonlinear optical applications apart holography and have the additional advantage to minimize the absorption even in the far-infrared (THz) range. The review also provides a discussion on the progress made in the characterization of non-stoichiometry related intrinsic and extrinsic defect structures in doped LN crystals, with emphasis on ODR-ion-doped and/or closely stoichiometric systems, based on both spectroscopic measurements and theoretical modelling, including the results of first principles quantum mechanical calculations on hydroxyl defects. It will also be shown that new perspective applications, e.g., the generation of high energy THz pulses with energies on the tens-of-mJ scale, are feasible with ODR-doped sLN crystals if optimal conditions, including the contact grating technique, are applied.

  9. Acoustic method for investigation of the structural defects in metals

    International Nuclear Information System (INIS)

    Nicolaescu, I.I.; Curcaneanu, Nicoleta

    1997-01-01

    In this work an acoustic method is presented called, the resonant bar method, which is based on the interaction between ultrasound and the structural defects in high purity metals. By this method the internal dislocation friction (Q -1 ) and the propagation velocity (v) of the ultrasound in the bar is measured. Both quantities are shown to depend on the dislocation densities and the length of dislocation loop. The experimental setup is shown. It consists of the resonant bar, the excitation spool, a generator of variable frequency and amplitude, a receptor spool, a selective amplifier and the adjacent measuring and displaying apparatus. The two spools are located inside of a toroidal permanent magnet. The bar oscillations are produced by the variable electromagnetic force appearing between the whirl current induced in the sample by the generator and the field of toroidal magnet. This method is applied to nonmagnetic materials with high electric conductivity. If the bar under study consists of a insulating material then on its ends either a conducting thin layer or a metallic thin sheet is deposed. The installation allows measuring the acoustic parameters of materials (v and Q -1 ) by two procedures, the method of free damped oscillations and the method of forced oscillations. Also, the internal friction can be measured with this installation, either dependent on or independent of the generator amplitude. Measurements on aluminium samples resulted in the following values: Q -1 (3 ppm) = 10 -3 and Q -1 (150 ppm) = 10 -5 . By means of this installation internal friction can be studied in re-baked, annealed, mechanical deformed and irradiated samples or in materials submitted to other processes

  10. Structure, stability and mobility of point defects in hexagonal close packed zirconium: an ab initio study

    International Nuclear Information System (INIS)

    Verite, G.

    2007-09-01

    This research aims at determining, by means of DFT (density functional theory) electronic structure computations, the structure, the stability, and the mobility of isolated point defects, lack defects, auto-interstitial defects, or small aggregate defects in the compact hexagonal zirconium (hc Zr). After a literature survey on the studied materials and a review of computer simulation methods in material science, the author presents and comments the available results from experiments or simulations on point defects in hc Zr. He presents the growth phenomenon under radiation. Then, he briefly described the computing techniques used in this study, reports the determination of the network parameters and elastic constants of each material. He reports and comments the results obtained with the SIESTA code and with a Monte Carlo kinetic simulation. The different types of defects are investigated

  11. Shallow nitrogen ion implantation: Evolution of chemical state and defect structure in titanium

    Energy Technology Data Exchange (ETDEWEB)

    Manojkumar, P.A., E-mail: manoj@igcar.gov.in [Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Chirayath, V.A.; Balamurugan, A.K.; Krishna, Nanda Gopala; Ilango, S.; Kamruddin, M.; Amarendra, G.; Tyagi, A.K. [Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Raj, Baldev [National Institute of Advanced Studies, Bangalore 560 012 (India)

    2016-09-15

    Highlights: • Low energy nitrogen ion implantation in titanium was studied. • Chemical and defect states were analyzed using SIMS, XPS and PAS. • SIMS and depth resolved XPS data showed good agreement. • Depth resolved defect and chemical states information were revealed. • Formation of 3 layers of defect states proposed to fit PAS results. - Abstract: Evolution of chemical states and defect structure in titanium during low energy nitrogen ion implantation by Plasma Immersion Ion Implantation (PIII) process is studied. The underlying process of chemical state evolution is investigated using secondary ion mass spectrometry and X-ray photoelectron spectroscopy. The implantation induced defect structure evolution as a function of dose is elucidated using variable energy positron annihilation Doppler broadening spectroscopy (PAS) and the results were corroborated with chemical state. Formation of 3 layers of defect state was modeled to fit PAS results.

  12. [Pyramidal syndrome in lateral amyotrophic sclerosis: clinico-morphological analysis].

    Science.gov (United States)

    Musaeva, L S; Zavalishin, I A; Gulevskaia, T S

    2003-01-01

    Retrospective clinical analysis with a special focus on pyramidal syndrome expression in the disease course as well as morphological study of brain and spinal structures in all levels of cortical-spinal projection (from brain motor cortex to spinal lumbar segments) have been conducted for 11 section cases of lateral amyotrophic sclerosis (LAS), sporadic type. Two groups of patients were studied: with pronounced pyramidal syndrome (spasticity, hyperreflexia, etc)--7 cases and with some signs of pyramidal deficiency (anisoreflexia, stability of peritoneal reflexes)--4 cases. Pyramidal syndrome in LAS is considered as an emergence of current neurodegenerative process, embracing a significant part of upper motor neurons of both precentral convolution and its axons along the whole length of cerebrospinal axis in the form of cytoplasmic inclusions and axonal spheroids. A presence of pathomorphological changes in other upper segmental structures of motor control reveals their role in pyramidal deficiency. Comparative analysis showed that expression of pyramidal syndrome signs and its correlation to atrophic paresis appearances is specifically determined by the severity of upper and lower motor neurons lesions. With regard to morphological changes in CNS structures, the peculiarities of some pyramidal syndrome appearances in LAS are analyzed.

  13. Imaging a Pyramid Interior by ERT-3D Methods, Preliminar Results at El Castillo Pyramid, Chichen Itza, Mexico

    Science.gov (United States)

    Chavez, R. E.; Tejero, A.; Cifuentes, G.; HernaNdez-Quintero, J. E.; Garcia-Serrano, A.

    2016-12-01

    The well known Pyramid El Castillo, located in the archaeological site of Chichen Itza, in the Yucatan Peninsula is the emblematic structure of this archaeological site and elected as one of the man-made world seven wonders. The archaeological team that restored this structure during the 1920's discovered a smaller pyramid inside this prehispanic body, which corresponded to an older Mayan period. The possibility of finding other constructive periods inside this edifice should be important to reconstruct the Mayan history. Previous geophysical studies carried out by us in 2014, employed novel Electrical Resistivity Tomography (ERT) arrays that surrounded the pyramids surface with flat electrodes to obtain a 3D image of the subsoil. At that time, a low resistivity body was found beneath the pyramid, which was associated to a sinkhole filled with sweet water. Employing the same technique, a series of flat electrodes were deployed on each body conforming the pyramid, a total of 10 bodies were covered, employing a different number of electrodes trying to keep the distance between each electrode constant ( 3 m). Each body was treated as a single observation cube, where the apparent resistivity data measured was later inverted. A precise topographic control for each electrode was realized and introduced in the inversion process. 45,000 observation points within the pyramid were obtained. Initially, each working cube corresponding to a given pyramid's body was inverted. A composition of each inversion was assembled to form the resistivity distribution within the pyramid using a smooth interpolation method. A high resistivity anomaly was found towards the northern portion of the model that could be associated to the main stairway of the inner pyramid. The cavity detected during the 2014 survey was observed as a low resistivity anomaly found at the pyramid's base. At the moment, we are assembling the full observed resistivity data as a single file to compute an integrated

  14. Influence of irradiation on defects creation in pin diode structure

    International Nuclear Information System (INIS)

    Sopko, V.; Dammer, J.; Sopko, B.; Chren, D.

    2012-01-01

    In this paper the manufacture of type S1 PIN diodes and radiation defect induce by fast neutrons were studied. A shift from VV"- to VV (neutral) is observed in neutron irradiated diodes. From the results obtained, an explanation that clearly offers itself is that the nature of the defects produced by irradiation of material exhibiting N type conductivity is different from those for type P material. Given that the experiments were conducted with the same material, i.e., the dopant present in the material remained unchanged, it can be stated that simply by changing the type of conductivity with increasing dose, a different kind of defects is produced, having different activation energies in the forbidden band. All these results are consistent with the ongoing RD 50 experiments at CERN.

  15. Structural defects in cubic semiconductors characterized by aberration-corrected scanning transmission electron microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Arroyo Rojas Dasilva, Yadira; Kozak, Roksolana; Erni, Rolf; Rossell, Marta D., E-mail: marta.rossell@empa.ch

    2017-05-15

    The development of new electro-optical devices and the realization of novel types of transistors require a profound understanding of the structural characteristics of new semiconductor heterostructures. This article provides a concise review about structural defects which occur in semiconductor heterostructures on the basis of micro-patterned Si substrates. In particular, one- and two-dimensional crystal defects are being discussed which are due to the plastic relaxation of epitaxial strain caused by the misfit of crystal lattices. Besides a few selected examples from literature, we treat in particular crystal defects occurring in GaAs/Si, Ge/Si and β-SiC/Si structures which are studied by high-resolution annular dark-field scanning transmission electron microscopy. The relevance of this article is twofold; firstly, it should provide a collection of data which are of help for the identification and characterization of defects in cubic semiconductors by means of atomic-resolution imaging, and secondly, the experimental data shall provide a basis for advancing the understanding of device characteristics with the aid of theoretical modelling by considering the defective nature of strained semiconductor heterostructures. - Highlights: • The heterogeneous integration of high-quality compound semiconductors remains a challenge. • Lattice defects cause severe degradation of the semiconductor device performances. • Aberration-corrected HAADF-STEM allows atomic-scale characterization of defects. • An overview of lattice defects found in cubic semiconductors is presented. • Theoretical modelling and calculations are needed to determine the defect properties.

  16. Pyramid solar micro-grid

    Science.gov (United States)

    Huang, Bin-Juine; Hsu, Po-Chien; Wang, Yi-Hung; Tang, Tzu-Chiao; Wang, Jia-Wei; Dong, Xin-Hong; Hsu, Hsin-Yi; Li, Kang; Lee, Kung-Yen

    2018-03-01

    A novel pyramid solar micro-grid is proposed in the present study. All the members within the micro-grid can mutually share excess solar PV power each other through a binary-connection hierarchy. The test results of a 2+2 pyramid solar micro-grid consisting of 4 individual solar PV systems for self-consumption are reported.

  17. PZT microfibre defect structure studied by Raman spectroscopy

    Czech Academy of Sciences Publication Activity Database

    Kozielski, L.; Buixaderas, Elena; Clemens, F.

    2010-01-01

    Roč. 43, č. 41 (2010), 415401/1-415401/6 ISSN 0022-3727 R&D Projects: GA ČR GAP204/10/0616 Institutional research plan: CEZ:AV0Z10100520 Keywords : point defects * phase transitions * Raman spectroscopy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.105, year: 2010

  18. Effect of grain boundary structures on the behavior of He defects in Ni: An atomistic study

    Institute of Scientific and Technical Information of China (English)

    H F Gong; Y Yan; X S Zhang; W Lv; T Liu; Q S Ren

    2017-01-01

    We investigated the effect of grain boundary structures on the trapping strength of HeN (N is the number of helium atoms) defects in the grain boundaries of nickel.The results suggest that the binding energy of an interstitial helium atom to the grain boundary plane is the strongest among all sites around the plane.The HeN defect is much more stable in nickel bulk than in the grain boundary plane.Besides,the binding energy of an interstitial helium atom to a vacancy is stronger than that to a grain boundary plane.The binding strength between the grain boundary and the HeN defect increases with the defect size.Moreover,the binding strength of the HeN defect to the Σ3 (1 12)[110] grain boundary becomes much weaker than that to other grain boundaries as the defect size increases.

  19. Influence of point defects on the near edge structure of hexagonal boron nitride

    Science.gov (United States)

    McDougall, Nicholas L.; Partridge, Jim G.; Nicholls, Rebecca J.; Russo, Salvy P.; McCulloch, Dougal G.

    2017-10-01

    Hexagonal boron nitride (hBN) is a wide-band-gap semiconductor with applications including gate insulation layers in graphene transistors, far-ultraviolet light emitting devices and as hydrogen storage media. Due to its complex microstructure, defects in hBN are challenging to identify. Here, we combine x-ray absorption near edge structure (XANES) spectroscopy with ab initio theoretical modeling to identify energetically favorable defects. Following annealing of hBN samples in vacuum and oxygen, the B and N K edges exhibited angular-dependent peak modifications consistent with in-plane defects. Theoretical calculations showed that the energetically favorable defects all produce signature features in XANES. Comparing these calculations with experiments, the principle defects were attributed to substitutional oxygen at the nitrogen site, substitutional carbon at the boron site, and hydrogen passivated boron vacancies. Hydrogen passivation of defects was found to significantly affect the formation energies, electronic states, and XANES. In the B K edge, multiple peaks above the major 1 s to π* peak occur as a result of these defects and the hydrogen passivated boron vacancy produces the frequently observed doublet in the 1 s to σ* transition. While the N K edge is less sensitive to defects, features attributable to substitutional C at the B site were observed. This defect was also calculated to have mid-gap states in its band structure that may be responsible for the 4.1-eV ultraviolet emission frequently observed from this material.

  20. Plain defects and their vortex configuration in dilute Mo-B alloys in dissipative structure

    International Nuclear Information System (INIS)

    Sofronova, R.M.

    1992-01-01

    Electron microscopic study of single crystal of Mo-0.003 mas.% B alloy after zone melting and annealing at 2373 K was conducted to reveal the nature of planar defects and the role of boron in their formation. It was shown that planar defects should be considered as preprecipitations of MoB nonequilibrous phase out of molybdenum base solid solution. A planar defect was found to constitute a monolayer of boron atoms which consisted of B-B zigzag-like chains. Inturn the chains were surrounded by Mo atoms which formed hexagonal prism. The coherency of planar defects with matrix was due to close lattice parameters of Mo, β-MoB and δ-MoB. The planar defects in molybdenum base alloy were considered as elements of dissipative structure. They determined formation of supercellular dislocation structure under deformation

  1. Nanopore fabricated in pyramidal HfO2 film by dielectric breakdown method

    Science.gov (United States)

    Wang, Yifan; Chen, Qi; Deng, Tao; Liu, Zewen

    2017-10-01

    The dielectric breakdown method provides an innovative solution to fabricate solid-state nanopores on insulating films. A nanopore generation event via this method is considered to be caused by random charged traps (i.e., structural defects) and high electric fields in the membrane. Thus, the position and number of nanopores on planar films prepared by the dielectric breakdown method is hard to control. In this paper, we propose to fabricate nanopores on pyramidal HfO2 films (10-nm and 15-nm-thick) to improve the ability to control the location and number during the fabrication process. Since the electric field intensity gets enhanced at the corners of the pyramid-shaped film, the probability of nanopore occurrence at vertex and edge areas increases. This priority of appearance provides us chance to control the location and number of nanopores by monitoring a sudden irreversible discrete increase in current. The experimental results showed that the probability of nanopore occurrence decreases in an order from the vertex area, the edge area to the side face area. The sizes of nanopores ranging from 30 nm to 10 nm were obtained. Nanopores fabricated on the pyramid-shaped HfO2 film also showed an obvious ion current rectification characteristic, which might improve the nanopore performance as a biomolecule sequencing platform.

  2. TCM Analysis of Defected Ground Structures for MIMO Antenna Designs in Mobile Terminals

    KAUST Repository

    Ghalib, Asim; Sharawi, Mohammad S.

    2017-01-01

    In this paper, the theory of characteristic modes (TCM) is used for the first time to analyze the behavior of defected ground structures (DGS) when added to antenna designs. A properly designed DGS introduces currents opposite in direction

  3. Methods of the Detection and Identification of Structural Defects in Saturated Metallic Composite Castings

    Directory of Open Access Journals (Sweden)

    Gawdzińska K.

    2017-09-01

    Full Text Available Diagnostics of composite castings, due to their complex structure, requires that their characteristics are tested by an appropriate description method. Any deviation from the specific characteristic will be regarded as a material defect. The detection of defects in composite castings sometimes is not sufficient and the defects have to be identified. This study classifies defects found in the structures of saturated metallic composite castings and indicates those stages of the process where such defects are likely to be formed. Not only does the author determine the causes of structural defects, describe methods of their detection and identification, but also proposes a schematic procedure to be followed during detection and identification of structural defects of castings made from saturated reinforcement metallic composites. Alloys examination was conducted after technological process, while using destructive (macroscopic tests, light and scanning electron microscopy and non-destructive (ultrasonic and X-ray defectoscopy, tomography, gravimetric method methods. Research presented in this article are part of author’s work on castings quality.

  4. Top-down cellular pyramids

    Energy Technology Data Exchange (ETDEWEB)

    Wu, A Y; Rosenfeld, A

    1983-10-01

    A cellular pyramid is an exponentially tapering stack of arrays of processors (cells), where each cell is connected to its neighbors (siblings) on its own level, to a parent on the level above, and to its children on the level below. It is shown that in some situations, if information flows top-down only, from fathers to sons, then a cellular pyramid may be no faster than a one-level cellular array; but it may be possible to use simpler cells in the pyramid case. 23 references.

  5. Computing Homology Group Generators of Images Using Irregular Graph Pyramids

    OpenAIRE

    Peltier , Samuel; Ion , Adrian; Haxhimusa , Yll; Kropatsch , Walter; Damiand , Guillaume

    2007-01-01

    International audience; We introduce a method for computing homology groups and their generators of a 2D image, using a hierarchical structure i.e. irregular graph pyramid. Starting from an image, a hierarchy of the image is built, by two operations that preserve homology of each region. Instead of computing homology generators in the base where the number of entities (cells) is large, we first reduce the number of cells by a graph pyramid. Then homology generators are computed efficiently on...

  6. Thermo-kinetic mechanisms for grain boundary structure multiplicity, thermal instability and defect interactions

    International Nuclear Information System (INIS)

    Burbery, N.J.; Das, R.; Ferguson, W.G.

    2016-01-01

    Grain boundaries (GBs) provide a source and/or a sink for crystal defects and store elastic energy due to the non-uniform atomic bonding structure of the GB core. GB structures are thermodynamically driven to transition to the lowest energy configuration possible; however to date there has been little evidence to explain why specific GB structures have a low energy state. Furthermore, there is little quantitative demonstration of the significance of physical and GB structure characteristics on the GB energy, thermal stability, and the effect of temporary local GB structure transformations on defect interactions. This paper evaluates the defect interactions and structure stability of multiple Σ5(310) GB structures in bi-crystals of pure aluminium, and systematically investigates the features at 0 K to characterise multiple metastable structures. Structure stability is evaluated by utilising unstable vacancy defects to initiate GB transformations, and using nudged elastic band simulations to quantify this with the activation energy. The emission of stable vacancy defects from the ‘stable’ and metastable grain boundaries is also evaluated in the same manner. A detailed analysis of dislocation nucleation at the atomistic scale demonstrates that local transformations of GB structure between stable and metastable intermediates can provide a mechanism to accommodate the generation of crystal defects. Kinetic (time-dependent) effects that compete with energetic driving forces for structural transformations of GBs are shown to cause a significant effect on the activation properties that may exceed the influence of GB potential energy. The results demonstrate that GB structural multiplicity can be associated with the generation and absorption of dislocations and vacancies. This paper demonstrates the suitability of atomistic simulations coupled with nudged elastic band simulations to evaluate fundamental thermodynamic properties of pure FCC metals. Overall, this paper

  7. Thermo-kinetic mechanisms for grain boundary structure multiplicity, thermal instability and defect interactions

    Energy Technology Data Exchange (ETDEWEB)

    Burbery, N.J. [Department of Mechanical Engineering, University of Auckland, Auckland 1010 (New Zealand); Das, R., E-mail: r.das@auckland.ac.nz [Department of Mechanical Engineering, University of Auckland, Auckland 1010 (New Zealand); Ferguson, W.G. [Department of Chemical and Materials Engineering, University of Auckland, Auckland 1010 (New Zealand)

    2016-08-15

    Grain boundaries (GBs) provide a source and/or a sink for crystal defects and store elastic energy due to the non-uniform atomic bonding structure of the GB core. GB structures are thermodynamically driven to transition to the lowest energy configuration possible; however to date there has been little evidence to explain why specific GB structures have a low energy state. Furthermore, there is little quantitative demonstration of the significance of physical and GB structure characteristics on the GB energy, thermal stability, and the effect of temporary local GB structure transformations on defect interactions. This paper evaluates the defect interactions and structure stability of multiple Σ5(310) GB structures in bi-crystals of pure aluminium, and systematically investigates the features at 0 K to characterise multiple metastable structures. Structure stability is evaluated by utilising unstable vacancy defects to initiate GB transformations, and using nudged elastic band simulations to quantify this with the activation energy. The emission of stable vacancy defects from the ‘stable’ and metastable grain boundaries is also evaluated in the same manner. A detailed analysis of dislocation nucleation at the atomistic scale demonstrates that local transformations of GB structure between stable and metastable intermediates can provide a mechanism to accommodate the generation of crystal defects. Kinetic (time-dependent) effects that compete with energetic driving forces for structural transformations of GBs are shown to cause a significant effect on the activation properties that may exceed the influence of GB potential energy. The results demonstrate that GB structural multiplicity can be associated with the generation and absorption of dislocations and vacancies. This paper demonstrates the suitability of atomistic simulations coupled with nudged elastic band simulations to evaluate fundamental thermodynamic properties of pure FCC metals. Overall, this paper

  8. Structure and flux pinning properties of irradiation defects in YBa2Cu3O7-x

    International Nuclear Information System (INIS)

    Kirk, M.A.

    1992-06-01

    We review our investigations of defects produced in YBa 2 Cu 3 O 7-x by various forms of irradiation. The defect microstructure has been studied by transmission electron microscopy (TEM). Irradiation enhancements of flux pinning have been studied by SQUID magnetometry on single crystals. In many cases the same single crystals were used in both TEM and SQUID investigations. The primary atom recoil spectra for all the irradiations studied have been carefully calculated and used to correlate the TEM and magnetization results for the different types of irradiation. Correlation of annealing experiments, employing both TEM and SQUID measurements, among several types of irradiation has also yielded information on the different defect structures present. Defect densities, sizes and strain field anisotropies have been determined by TEM. Defect flux pinning anisotropies have been determined for two field orientations in twinned single crystals. The temperature dependences of the flux pinning have been measured. The maximum field of irreversibility at 70 K is shown to change markedly upon both neutron and proton irradiations in some crystals and not others. The defect structure, chemistry and location in the unit cell has been determined in some cases. Some interaction with existing defect structure has been observed in proton and electron irradiations. The damage character and directionality has been determined in GeV ion irradiated crystals

  9. The Pyramidal Capacitated Vehicle Routing Problem

    DEFF Research Database (Denmark)

    Lysgaard, Jens

    This paper introduces the Pyramidal Capacitated Vehicle Routing Problem (PCVRP) as a restricted version of the Capacitated Vehicle Routing Problem (CVRP). In the PCVRP each route is required to be pyramidal in a sense generalized from the Pyramidal Traveling Salesman Problem (PTSP). A pyramidal...

  10. The pyramidal capacitated vehicle routing problem

    DEFF Research Database (Denmark)

    Lysgaard, Jens

    2010-01-01

    This paper introduces the pyramidal capacitated vehicle routing problem (PCVRP) as a restricted version of the capacitated vehicle routing problem (CVRP). In the PCVRP each route is required to be pyramidal in a sense generalized from the pyramidal traveling salesman problem (PTSP). A pyramidal...

  11. Electron beam generation and structure of defects in carbon and boron nitride nano-tubes

    Energy Technology Data Exchange (ETDEWEB)

    Zobelli, A

    2007-10-15

    The nature and role of defects is of primary importance to understand the physical properties of C and BN (boron nitride) single walled nano-tubes (SWNTs). Transmission electron microscopy (TEM) is a well known powerful tool to study the structure of defects in materials. However, in the case of SWNTs, the electron irradiation of the TEM may knock out atoms. This effect may alter the native structure of the tube, and has also been proposed as a potential tool for nano-engineering of nano-tubular structures. Here we develop a theoretical description of the irradiation mechanism. First, the anisotropy of the emission energy threshold is obtained via density functional based calculations. Then, we numerically derive the total Mott cross section for different emission sites of carbon and boron nitride nano-tubes with different chiralities. Using a dedicated STEM (Scanning Transmission Electron Microscope) microscope with experimental conditions optimised on the basis of derived cross-sections, we are able to control the generation of defects in nano-tubular systems. Either point or line defects can be obtained with a spatial resolution of a few nanometers. The structure, energetics and electronics of point and line defects in BN systems have been investigated. Stability of mono- and di- vacancy defects in hexagonal boron nitride layers is investigated, and their activation energies and reaction paths for diffusion have been derived using the nudged elastic band method (NEB) combined with density functional based techniques. We demonstrate that the appearance of extended linear defects under electron irradiation is more favorable than a random distribution of point defects and this is due to the existence of preferential sites for atom emission in the presence of pre-existing defects, rather than thermal vacancy nucleation and migration. (author)

  12. Electron beam generation and structure of defects in carbon and boron nitride nano-tubes

    International Nuclear Information System (INIS)

    Zobelli, A.

    2007-10-01

    The nature and role of defects is of primary importance to understand the physical properties of C and BN (boron nitride) single walled nano-tubes (SWNTs). Transmission electron microscopy (TEM) is a well known powerful tool to study the structure of defects in materials. However, in the case of SWNTs, the electron irradiation of the TEM may knock out atoms. This effect may alter the native structure of the tube, and has also been proposed as a potential tool for nano-engineering of nano-tubular structures. Here we develop a theoretical description of the irradiation mechanism. First, the anisotropy of the emission energy threshold is obtained via density functional based calculations. Then, we numerically derive the total Mott cross section for different emission sites of carbon and boron nitride nano-tubes with different chiralities. Using a dedicated STEM (Scanning Transmission Electron Microscope) microscope with experimental conditions optimised on the basis of derived cross-sections, we are able to control the generation of defects in nano-tubular systems. Either point or line defects can be obtained with a spatial resolution of a few nanometers. The structure, energetics and electronics of point and line defects in BN systems have been investigated. Stability of mono- and di- vacancy defects in hexagonal boron nitride layers is investigated, and their activation energies and reaction paths for diffusion have been derived using the nudged elastic band method (NEB) combined with density functional based techniques. We demonstrate that the appearance of extended linear defects under electron irradiation is more favorable than a random distribution of point defects and this is due to the existence of preferential sites for atom emission in the presence of pre-existing defects, rather than thermal vacancy nucleation and migration. (author)

  13. Structural and electronic properties of zigzag InP nanoribbons with Stone–Wales type defects

    International Nuclear Information System (INIS)

    Longo, R C; Carrete, J; Varela, L M; Gallego, L J

    2016-01-01

    By means of density-functional-theoretic calculations, we investigate the structural and electronic properties of a hexagonal InP sheet and of hydrogen-passivated zigzag InP nanoribbons (ZInPNRs) with Stone–Wales (SW)-type defects. Our results show that the influence of this kind of defect is not limited to the defected region but it leads to the formation of ripples that extend across the systems, in keeping with the results obtained recently for graphene and silicene sheets. The presence of SW defects in ZInPNRs causes an appreciable broadening of the band gap and transforms the indirect-bandgap perfect ZInPNR into a direct-bandgap semiconductor. An external transverse electric field, regardless of its direction, reduces the gap in both the perfect and defective ZInPNRs. (paper)

  14. First Trimester Influenza Vaccination and Risks for Major Structural Birth Defects in Offspring.

    Science.gov (United States)

    Kharbanda, Elyse Olshen; Vazquez-Benitez, Gabriela; Romitti, Paul A; Naleway, Allison L; Cheetham, T Craig; Lipkind, Heather S; Klein, Nicola P; Lee, Grace; Jackson, Michael L; Hambidge, Simon J; McCarthy, Natalie; DeStefano, Frank; Nordin, James D

    2017-08-01

    To examine risks for major structural birth defects in infants after first trimester inactivated influenza vaccine (IIV) exposures. In this observational study, we used electronic health data from 7 Vaccine Safety Datalink sites to examine risks for selected major structural defects in infants after maternal IIV exposure. Vaccine exposures for women with continuous insurance enrollment through pregnancy who delivered singleton live births between 2004 and 2013 were identified from standardized files. Infants with continuous insurance enrollment were followed to 1 year of age. We excluded mother-infant pairs with other exposures that potentially increased their background risk for birth defects. Selected cardiac, orofacial or respiratory, neurologic, ophthalmologic or otologic, gastrointestinal, genitourinary and muscular or limb defects were identified from diagnostic codes in infant medical records using validated algorithms. Propensity score adjusted generalized estimating equations were used to estimate prevalence ratios (PRs). We identified 52 856 infants with maternal first trimester IIV exposure and 373 088 infants whose mothers were unexposed to IIV during first trimester. Prevalence (per 100 live births) for selected major structural birth defects was 1.6 among first trimester IIV exposed versus 1.5 among unexposed mothers. The adjusted PR was 1.02 (95% CI 0.94-1.10). Organ system-specific PRs were similar to the overall PR. First trimester maternal IIV exposure was not associated with an increased risk for selected major structural birth defects in this large cohort of singleton live births. Copyright © 2017 Elsevier Inc. All rights reserved.

  15. Tuning optical properties of opal photonic crystals by structural defects engineering

    Science.gov (United States)

    di Stasio, F.; Cucini, M.; Berti, L.; Comoretto, D.; Abbotto, A.; Bellotto, L.; Manfredi, N.; Marinzi, C.

    2009-06-01

    We report on the preparation and optical characterization of three dimensional colloidal photonic crystal (PhC) containing an engineered planar defect embedding photoactive push-pull dyes. Free standing polystyrene films having thickness between 0.6 and 3 mm doped with different dipolar chromophores were prepared. These films were sandwiched between two artificial opals creating a PhC structure with planar defect. The system was characterized by reflectance at normal incidence angle (R), variable angle transmittance (T) and photoluminescence spectroscopy (PL) Evidence of defect states were observed in T and R spectra which allow the light to propagate for selected frequencies within the pseudogap (stop band).

  16. Study of reticular defects in V3Si (A15 structure)

    International Nuclear Information System (INIS)

    Ben Lamine, Abdelmottaleb

    1980-01-01

    The A15 crystal structure is that of superconductive compounds with high critical temperature. This research thesis aims at studying its possible reticular defects. In a first part, the author presents this structure and more particularly its crystallographic properties, reports the indexing of electronic diffraction diagrams (point diagrams and line diagrams of Kikuchi) in the case of V 3 Si. Then, after having described the sample preparation technique, the author reports the study of reticular defects by high voltage electronic microscopy on a raw V 3 Si crystal. The existence of a specific defect is highlighted and the crystallographic study of this defect is reported. It has been performed by means of computer-based simulation of contrast (TWODIS software). Results are then discussed

  17. Influence on ultrasonic incident angle and defect detection sensitivity by cast stainless steel structure

    International Nuclear Information System (INIS)

    Kurozumi, Y.

    2004-01-01

    It is well known that ultrasonic waves are affected strongly by macro-structures in cast stainless steel, as in the primary pipe or other components in pressurized water reactors (PWRs). In this work, ultrasonic refractive angles and defect detection sensitivities are investigated at different incident angles to cast stainless steel. The aims of the investigation are to clarify the transmission of ultrasonic waves in cast stainless steel and to contribute to the transducer design. The results are that ultrasonic refractive angles in cast stainless steel shift towards the 45-degree direction with respect to the direction of dendritic structures by 11.8 degrees at the maximum and that the sensitivity of transducer for inner surface breaking cracks increases with decreasing incident angle. However, in an ultrasonic inspection of actual welds at smaller incident angles, a trade-off occurs between increased defect detection sensitivity and decreased defect discrimination capability due to intense false signals produced by non-defective features. (orig.)

  18. Method of determining external defects of a structure by analyzing a series of its images in the monitoring system

    Directory of Open Access Journals (Sweden)

    Loktev Aleksey Alekseevich

    2015-03-01

    geometrical parameters by analyzing a series of images. This is the issue and the subject of this work, which developed the computational algorithms to detect external defects. At the stage of preliminary image processing there is the delineation of characteristic points in the image and the calculation of the optical flow in the area of these points. When determining the defect position, the characteristic points of the image are determined using the detector of Harris-Laplace, which are located in the central part of the image. The characteristic points outside the frame are considered to be background. There is an identification of the changes in characteristic points in the frame in relation to the background by using a pyramidal iterative scheme. In the second stage servo frame focuses on a specific point with the greatest change in relation to the background in the current time. The algorithm for object detection and determination of its parameters includes three procedures: detection procedure start; the procedure of the next image processing; stop procedure for determining the parameters of the object. The method described here can be used to create information-measuring system of monitoring based on the use of photodetectors with high-definition and recognition of defects (color differences and differences in the form compared to the background. Since almost each examination of a building or structure begins with a visual examination and determination of the most probable places of occurrence and presence of the defects, the proposed method can be combined with this stage and it will simplify the process of diagnosing, screening for the development of projects on reconstruction and placement of additional equipment on the existing infrastructure.

  19. Role of the bond defect for structural transformations between crystalline and amorphous silicon: A molecular-dynamics study

    International Nuclear Information System (INIS)

    Stock, D. M.; Weber, B.; Gaertner, K.

    2000-01-01

    The relation between the bond defect, which is a topological defect, and structural transformations between crystalline and amorphous silicon, is studied by molecular-dynamics simulations. The investigation of 1-keV boron implantation into crystalline silicon proves that the bond defect can also be generated directly by collisional-induced bond switching in addition to its formation by incomplete recombination of primary defects. This supports the assumption that the bond defect may play an important role in the amorphization process of silicon by light ions. The analysis of the interface between (001) silicon and amorphous silicon shows that there are two typical defect configurations at the interface which result from two different orientations of the bond defect with respect to the interface. Thus the bond defect appears to be a characteristic structural feature of the interface. Moreover, annealing results indicate that the bond defect acts as a growth site for interface-mediated crystallization

  20. Research Trends on Defect and Life Assessment of High Temperature Structure

    International Nuclear Information System (INIS)

    Lee, Hyeong Yeon; Lee Jae Han

    2008-01-01

    This report presents the analysis on the state-of-the-art research trends on defect assessment and life evaluation of high temperature structure based on the papers presented in the two international conferences of ASME PVP 2007 / CREEP 8 which was held in 2007 and ICFDSM VI(International Conference on Fatigue Damage of Structural Materials VI) which was held in 2006

  1. Base-of-the-pyramid global strategy

    Directory of Open Access Journals (Sweden)

    Boşcor, D.

    2010-12-01

    Full Text Available Global strategies for MNCs should focus on customers in emerging and developing markets instead of customers in developed economies. The “base-of-the-pyramid segment” comprises 4 billion people in the world. In order to be successful, companies will be required to form unconventional partnerships- with entities ranging from local governments to non-profit organizations - to gain the community’s trust and understand the environmental, infrastructure and political issues that may affect business. Being able to provide affordable, high-quality products and services in this market segment often means new approaches to marketing- new packaging and pricing structures, and using unfamiliar distribution structures.

  2. Structural evolution of defective graphene under heat treatment and gamma irradiation

    Science.gov (United States)

    Zhang, Yifei; Shi, Jie; Chen, Cheng; Li, Nan; Xu, Zhiwei; Liu, Liangsen; Zhao, Lihuan; Li, Jing; Jing, Miaolei

    2018-03-01

    We have studied the structural change of defective graphene built by annealing in different temperature under the condition of gamma irradiation. Firstly, we found the heat treatment not only reduced but also striped the graphene. This behavior made defects become more firstly and then become less with the increase of temperature. And then gamma irradiation removed some oxygen-containing groups, by a simultaneous changed over carbon in the graphitic lattice from sp3 to sp2. Also, the gamma irradiation decreased the interlayer spacing between graphene lowest to 3.391 Å and made a crosslink which resulting in the size of the ordered gaining. A variation was detected by Raman spectroscopy that the amorphous carbon was declined after gamma irradiation. Furtherly we found the degree of this decline raised first and then diminished with the increase in the number of defects. The change in repair capacity of gamma irradiation presented a strategy for repairing the defects of graphene.

  3. Energetics of intrinsic point defects in uranium dioxide from electronic-structure calculations

    International Nuclear Information System (INIS)

    Nerikar, Pankaj; Watanabe, Taku; Tulenko, James S.; Phillpot, Simon R.; Sinnott, Susan B.

    2009-01-01

    The stability range of intrinsic point defects in uranium dioxide is determined as a function of temperature, oxygen partial pressure, and non-stoichiometry. The computational approach integrates high accuracy ab initio electronic-structure calculations and thermodynamic analysis supported by experimental data. In particular, the density functional theory calculations are performed at the level of the spin polarized, generalized gradient approximation and includes the Hubbard U term; as a result they predict the correct anti-ferromagnetic insulating ground state of uranium oxide. The thermodynamic calculations enable the effects of system temperature and partial pressure of oxygen on defect formation energy to be determined. The predicted equilibrium properties and defect formation energies for neutral defect complexes match trends in the experimental literature quite well. In contrast, the predicted values for charged complexes are lower than the measured values. The calculations predict that the formation of oxygen interstitials becomes increasingly difficult as higher temperatures and reducing conditions are approached

  4. The effect of defects on structural failure: A two-criteria approach

    International Nuclear Information System (INIS)

    Dowling, A.R.; Townley, C.H.A.

    1976-01-01

    The two-criteria approach to the study of defects in structures assumes that failure occurs when the applied load reaches the lower of either a load to cause brittle failure in accordance with the theories of linear elastic fracture mechanics or a collapse load dependent on the ultimate stress of the material and the structural geometry. This simple approach is described and compared with previously published experimental results for various geometries and materials. The simplicity of this method of defect analysis lies in the fact that each criterion is sufficiently well understood to permit scaling and geometry changes to be accommodated readily. It becomes apparent that a sizeable transition region exists between the two criteria but this can be described in an expression relating the criteria. This expression adequately predicts the behaviour of cracked structures of both simple and complex geometry. A design curve for defect assessment is proposed for which it is unnecessary to consider the transition region. (author)

  5. Fabrication of micromirrors with pyramidal shape using anisotropic etching of silicon

    OpenAIRE

    Moktadir, Z.; Vijaya Prakash, G.; Trupke, M.; Koukharenko, E.; Kraft, M.; Baumberg, J.J.; Eriksson, S.; Hinds, E.A.

    2005-01-01

    Gold micro-mirrors have been formed in silicon in an inverted pyramidal shape. The pyramidal structures are created in the (100) surface of a silicon wafer by anisotropic etching in potassium hydroxide. High quality micro-mirrors are then formed by sputtering gold onto the smooth silicon (111) faces of the pyramids. These mirrors show great promise as high quality optical devices suitable for integration into MOEMS systems.

  6. On the Advantages and Defects of the American Structuralism

    Institute of Scientific and Technical Information of China (English)

    徐晓莹

    2004-01-01

    During the years at the end of the nineteenth century and beginning of the twentieth century when Saussure was working out his ideas in Europe, synchronic linguistics was emerging independently, and in a very different style, in America, under the leadership of the anthropologist Franz Boas. Boas set a direction for American linguistics. The school founded by Boas was called structural linguistics. Beside Boas, the other two major representatives of this school during this period were: Sapir and Bloomfield.

  7. Thermographic inspection of bond defects in Fiber Reinforced Polymer applied to masonry structures

    Science.gov (United States)

    Masini, N.; Aiello, M. A.; Capozzoli, L.; Vasanelli, E.

    2012-04-01

    Nowadays, externally bonded Fiber Reinforced Polymers (FRP) are extensively used for strengthening and repairing masonry and reinforced concrete existing structures; they have had a rapid spread in the area of rehabilitation for their many advantages over other conventional repair systems, such as lightweight, excellent corrosion and fatigue resistance, high strength, etc. FRP systems applied to masonry or concrete structures are typically installed using a wet-layup technique.The method is susceptible to cause flaws or defects in the bond between the FRP system and the substrate, which may reduce the effectiveness of the reinforcing systems and the correct transfer of load from the structure to the composite. Thus it is of primary importance to detect the presence of defects and to quantify their extension in order to eventually provide correct repair measurements. The IR thermography has been cited by the several guidelines as a good mean to qualitatively evaluate the presence of installation defects and to monitor the reinforcing system with time.The method is non-destructive and does not require contact with the composite or other means except air to detect the reinforcement. Some works in the literature have been published on this topic. Most of the researches aim at using the IR thermography technique to characterize quantitatively the defects in terms of depth, extension and type in order to have an experimental database on defect typology to evaluate the long term performances of the reinforcing system. Nevertheless, most of the works in the literature concerns with FRP applied to concrete structures without considering the case of masonry structures. In the present research artificial bond defects between FRP and the masonry substrate have been reproduced in laboratory and the IR multi temporal thermography technique has been used to detect them. Thermographic analysis has been carried out on two wall samples having limited dimensions (100 x 70 cm) both

  8. Visualization and automatic detection of defect distribution in GaN atomic structure from sampling Moiré phase.

    Science.gov (United States)

    Wang, Qinghua; Ri, Shien; Tsuda, Hiroshi; Kodera, Masako; Suguro, Kyoichi; Miyashita, Naoto

    2017-09-19

    Quantitative detection of defects in atomic structures is of great significance to evaluating product quality and exploring quality improvement process. In this study, a Fourier transform filtered sampling Moire technique was proposed to visualize and detect defects in atomic arrays in a large field of view. Defect distributions, defect numbers and defect densities could be visually and quantitatively determined from a single atomic structure image at low cost. The effectiveness of the proposed technique was verified from numerical simulations. As an application, the dislocation distributions in a GaN/AlGaN atomic structure in two directions were magnified and displayed in Moire phase maps, and defect locations and densities were detected automatically. The proposed technique is able to provide valuable references to material scientists and engineers by checking the effect of various treatments for defect reduction. © 2017 IOP Publishing Ltd.

  9. The Base of the Pyramid

    NARCIS (Netherlands)

    Hutte, E.; Vermeulen, P.A.M.; Vermeulen, P.; Hutte, E.

    2014-01-01

    This chapter provides a brief background to the Base of the Pyramid (BoP) phenomenon. It begins with a discussion on what sets the BoP markets apart from more traditional markets and why companies have not identified them as a business opportunity. The chapter then provides an overview of how

  10. Structural defect generation in indium antimonide single crystals during electro-erosion cutting

    International Nuclear Information System (INIS)

    Kravetskij, M.Yu.; Matsas, E.P.; Skorokhod, M.Ya.; Fomin, A.V.; Khromyak, K.Ya.

    1990-01-01

    Using X-ray topography structural defects generating during electro-erosion cutting of InSb single crystals are studied. It is shown that dislocations, are introduced into so cut dislocation-free ingot plates, nucleation centers being located on their surfaces. It is detected that foreign phase inclusions in InSb are efficient sources of dislocations during cutting

  11. Effect of Hydrostatic Pressure on Defect Structure and Durability of Ultrafine-Grained Aluminum

    Czech Academy of Sciences Publication Activity Database

    Betekhtin, V.I.; Kadomtsev, A. G.; Sklenička, Václav; Narykova, M. V.

    2011-01-01

    Roč. 37, č. 10 (2011), s. 977-979 ISSN 1063-7850 Institutional research plan: CEZ:AV0Z20410507 Keywords : defect structure * ultrafine-grained aluminium * durability Subject RIV: JG - Metallurgy Impact factor: 0.565, year: 2011

  12. Synthesis and structural characterization of defect spinels in the Lithium-Manganese-Oxide system

    CSIR Research Space (South Africa)

    Thackeray, MM

    1993-10-01

    Full Text Available Lithium-manganese-oxides prepared at moderate temperatures are under investigation as insertion electrodes for rechargeable lithium batteries. The structures of two defect-spinel compounds synthesised by the reaction of MnCO3 and Li2CO3 at 400...

  13. Synthesis and structural characterization of defect spinels in the lithium-manganese-oxide system

    CSIR Research Space (South Africa)

    Thackeray, MM

    1993-10-01

    Full Text Available Lithium-manganese-oxides prepared at moderate temperatures are under investigation as insertion electrodes for rechargeable lithium batteries. The structures of two defect-spinel compounds synthesized by the reaction of MnCO3 and Li2CO3 at 400°C...

  14. Investigation of the Great Pyramid of Giza.

    Science.gov (United States)

    Peace, Nigel; And Others

    1997-01-01

    Describes an activity in which geometry and trigonometry are studied using pyramids. Identical model pyramids are constructed from card stock, along with pyramids of different proportions and cuboids to use as controls. Also includes an investigation of some apparently non-scientific claims. (DDR)

  15. Radiation defect formation in two-barrier structures based on silicon

    International Nuclear Information System (INIS)

    Madatov, R.S.; Abbasov, F.P.; Mustafayev, Yu.M.

    2013-01-01

    It was developed a silicon-based photodetector with high integral sensitivity in low-wave spectrum. It was investigated the effect of gamma radiation on the mechanism of current transport in the structure of Schottky barrier type and in transitions. It is shown that the double-barrier structures can improve the photovoltaic parameters of conventional detectors. For the first time it was obtained and studied the characteristics of two-barrier structures created on the same plane. The advantages over conventional structures are shown. The annealing point is changing the structure of radiation defects and leads to their disappearance

  16. Tailoring the strain in Si nano-structures for defect-free epitaxial Ge over growth.

    Science.gov (United States)

    Zaumseil, P; Yamamoto, Y; Schubert, M A; Capellini, G; Skibitzki, O; Zoellner, M H; Schroeder, T

    2015-09-04

    We investigate the structural properties and strain state of Ge nano-structures selectively grown on Si pillars of about 60 nm diameter with different SiGe buffer layers. A matrix of TEOS SiO2 surrounding the Si nano-pillars causes a tensile strain in the top part at the growth temperature of the buffer that reduces the misfit and supports defect-free initial growth. Elastic relaxation plays the dominant role in the further increase of the buffer thickness and subsequent Ge deposition. This method leads to Ge nanostructures on Si that are free from misfit dislocations and other structural defects, which is not the case for direct Ge deposition on these pillar structures. The Ge content of the SiGe buffer is thereby not a critical parameter; it may vary over a relatively wide range.

  17. Defect study in ZnO related structures-A multi-spectroscopic approach

    International Nuclear Information System (INIS)

    Ling, C.C.; Cheung, C.K.; Gu, Q.L.; Dai, X.M.; Xu, S.J.; Zhu, C.Y.; Luo, J.M.; Zhu, C.Y.; Tam, K.H.; Djurisic, A.B.; Beling, C.D.; Fung, S.; Lu, L.W.; Brauer, G.; Anwand, W.; Skorupa, W.; Ong, H.C.

    2008-01-01

    ZnO has attracted a great deal of attention in recent years because of its potential applications for fabricating optoelectronic devices. Using a multi-spectroscopic approach including positron annihilation spectroscopy (PAS), deep level transient spectroscopy (DLTS), photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS), we have studied the two observed phenomena from ZnO related structures. They namely included the H 2 O 2 pre-treatment induced ohmic to rectifying contact conversion on Au/n-ZnO contact and the p-type doping by nitrogen ion implantation. The aim of the studies was to offering comprehensive views as to how the defects influenced the structures electrical and optical properties of the structures. It was also shown that PAS measurement using the monoenergetic positron beam could offer valuable information of vacancy type defects in the vertical ZnO nanorod array structure

  18. Defect study in ZnO related structures-A multi-spectroscopic approach

    Energy Technology Data Exchange (ETDEWEB)

    Ling, C.C. [Department of Physics, The University of Hong Kong, Pokfulam Road, Hong Kong (China)], E-mail: ccling@hku.hk; Cheung, C.K.; Gu, Q.L.; Dai, X.M.; Xu, S.J.; Zhu, C.Y.; Luo, J.M.; Zhu, C.Y.; Tam, K.H.; Djurisic, A.B.; Beling, C.D.; Fung, S.; Lu, L.W. [Department of Physics, The University of Hong Kong, Pokfulam Road, Hong Kong (China); Brauer, G.; Anwand, W.; Skorupa, W. [Institut fuer Ionenstrahlphysik und Materialforschung, Forschungszentrum Dresden-Rossendorf, Postfach 510119, D-01314 Dresden (Germany); Ong, H.C. [Department of Physics, Chinese University of Hong Kong, Shatin, Hong Kong (China)

    2008-10-31

    ZnO has attracted a great deal of attention in recent years because of its potential applications for fabricating optoelectronic devices. Using a multi-spectroscopic approach including positron annihilation spectroscopy (PAS), deep level transient spectroscopy (DLTS), photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS), we have studied the two observed phenomena from ZnO related structures. They namely included the H{sub 2}O{sub 2} pre-treatment induced ohmic to rectifying contact conversion on Au/n-ZnO contact and the p-type doping by nitrogen ion implantation. The aim of the studies was to offering comprehensive views as to how the defects influenced the structures electrical and optical properties of the structures. It was also shown that PAS measurement using the monoenergetic positron beam could offer valuable information of vacancy type defects in the vertical ZnO nanorod array structure.

  19. Effects of deep impurities and structural defects in polycrystalline silicon for photovoltaic applications

    International Nuclear Information System (INIS)

    Galluzzi, F.; Scafe, E.; Beghi, M.; Fossati, S.; Tincani, M.; Pizzini, S.

    1985-01-01

    An extensive experimental study of minority carrier recombination in CZ grown polycrystalline silicon intentionally doped with metallic impurities (Ti, V, Fe, Cr, Zr) is reported. Experimental values of average diffusion lengths have been compared with values calculated by a simple model of carrier recombination, taking into account the effects of impurities, grain boundaries and intragrain crystal defects. The results are fairly consistent and allow the determination of threshold densities for structural defects and deep impurities. The author's analysis gives a simple quantitative description of recombination processes in solar-grade silicon, as far as the average behaviour is concerned

  20. Defect structures in YBa2Cu3O/sub 7-x/ produced by electron irradiation

    International Nuclear Information System (INIS)

    Kirk, M.A.; Baker, M.C.; Liu, J.Z.; Lam, D.J.; Weber, H.W.

    1987-12-01

    Defect structures in YBa 2 Cu 3 O/sub 7-x/ produced by electron irradiation at 300 0 K were investigated by transmission electron microscopy. Threshold energies for the production of visible defects were determined to be 152 keV and 131 keV (+- 7 keV) in directions near the a and b (b > a) axes (both perpendicular to c, the long axis in the orthorhombic structure), respectively. During above threshold irradiations in an electron flux of 3 x 10 18 cm -2 s -1 , extended defects were observed to form and grow to sizes of 10 to 50 nm over 1000 s in material thicknesses 20 to 200 nm. Such low electron threshold energies suggest oxygen atom displacements with recoil energies near 20 eV. The observation of movement of twin boundaries during irradiation just above threshold suggests movement of the basal plane oxygen atoms by direct displacement or defect migration processes. Crystals irradiated above threshold were observed after about 24 hours to have transformed to a structure heavily faulted on planes perpendicular to the c axis. 3 refs., 3 figs

  1. Remote defect imaging for plate-like structures based on the scanning laser source technique

    Science.gov (United States)

    Hayashi, Takahiro; Maeda, Atsuya; Nakao, Shogo

    2018-04-01

    In defect imaging with a scanning laser source technique, the use of a fixed receiver realizes stable measurements of flexural waves generated by laser at multiple rastering points. This study discussed the defect imaging by remote measurements using a laser Doppler vibrometer as a receiver. Narrow-band burst waves were generated by modulating laser pulse trains of a fiber laser to enhance signal to noise ratio in frequency domain. Averaging three images obtained at three different frequencies suppressed spurious distributions due to resonance. The experimental system equipped with these newly-devised means enabled us to visualize defects and adhesive objects in plate-like structures such as a plate with complex geometries and a branch pipe.

  2. Effects of graphene defect on electronic structures of its interface with organic semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Qing-Dan; Wang, Chundong; Mo, Hin-Wai; Lo, Ming-Fai; Yuen, Muk Fung; Ng, Tsz-Wai, E-mail: tszwaing@cityu.edu.hk, E-mail: apcslee@cityu.edu.hk; Zhang, Wen-Jun; Lee, Chun-Sing, E-mail: tszwaing@cityu.edu.hk, E-mail: apcslee@cityu.edu.hk [Department of Physics and Materials Science, Center of Super-Diamond and Advanced Films (COSDAF), City University of Hong Kong (Hong Kong); Dou, Wei-Dong [Department of Physics and Materials Science, Center of Super-Diamond and Advanced Films (COSDAF), City University of Hong Kong (Hong Kong); Physics Department, Shaoxing University, Shaoxing 312000 (China); Tsang, Sai-Wing [Department of Physics and Materials Science, City University of Hong Kong (Hong Kong)

    2015-03-30

    Electronic structures of copper hexadecafluorophthalocyanine (F{sub 16}CuPc)/graphene with different defect density were studied with ultra-violet photoelectron spectroscopy. We showed that the charge transfer interaction and charge flow direction can be interestingly tuned by controlling the defect density of graphene through time-controlled H{sub 2} plasma treatment. By increasing the treatment time of H{sub 2} plasma from 30 s to 5 min, both the interface surface dipole and the electron transporting barrier at F{sub 16}CuPc/graphene interface are significantly reduced from 0.86 to 0.56 eV and 0.71 to 0.29 eV, respectively. These results suggested that graphene's defect control is a simple approach for tuning electronic properties of organic/graphene interfaces.

  3. Defects in ZnO, CdTe, and Si: Optical, structural, and electrical characterization

    CERN Multimedia

    Deicher, M; Kronenberg, J; Johnston, K; Roder, J; Byrne, D J

    Electronic and optical properties of semiconductors are extremely sensitive to defects and impurities that have localized electronic states with energy levels in the band gap of the semiconductor. Spectroscopic techniques like photo-luminescence (PL), deep level transient spectroscopy (DLTS), or Hall effect that are able to detect and characterize band gap states do not reveal direct information about their microscopic origin. To overcome this chemical "blindness" radioactive isotopes are used as a tracer. Moreover, the recoil energies involved in ${\\beta}$- and ${\\gamma}$-decays can be used to create intrinsic, isolated point defects (interstitials, vacancies) in a controlled way. A microscopic insight into the structure and the thermodynamic properties of complexes formed by interacting defects can be gained by detecting the hyperfine interaction between the nuclear moments of radioactive dopants and the electromagnetic fields present at the site of the radioactive nucleus. These techniques will be used to...

  4. Comprehensive Study of Solar Cell Structure Defects by Means of Noise and Light Emission Analysis

    Directory of Open Access Journals (Sweden)

    Robert Macku

    2012-01-01

    Full Text Available This paper discusses the issue of silicon solar cells localized defects from metrological and physical points of view. Structure imperfections represent the real problem because of solar cells long-term degradation and conversion efficiency decreasing. To this aim we pay our attention to research relating to the defect light emission and correlation with rectangular microplasma fluctuation. A sensitive CCD camera has been used for mapping of surface photon emission. The operation point of the samples has been set to reverse bias mode, and different electric field intensity was applied. We managed to get interesting information using a combination of optical investigation and electrical noise measurement in time and spectral domain. It will be revealed that a direct correlation between noise and photon emission exists and the results related to several defect spots are presented in detail in this paper.

  5. Transmission electron microscopy of defects and internal fields in GaN structures

    Energy Technology Data Exchange (ETDEWEB)

    Mokhtari, H

    2001-07-01

    The main aim of this study was to understand the microstructure of GaN and InGaN/GaN and to examine electric fields around the defects, and across the quantum wells by electron holography. For this reason different types of GaN and InGaN/GaN samples have been prepared and studied. Conventional transmission electron microscopy has been used for structural study of two MBE grown GaN/GaAs samples, grown at room temperature and at 340 deg C. The structure of the samples were found to be hexagonal polycrystalline in an amorphous GaN matrix, and textured hexagonal polycrystalline material respectively. The experimental results indicate that the higher growth temperature results in a more crystalline material with a higher density of bigger grain sizes. Different types of undoped and Si doped GaN/Sapphire samples were studied, with respect to the defect structure in GaN films. GaN was found to be a highly defective material with a dislocation density of 10{sup 9}/cm{sup 2}. The majority of the dislocations are edge dislocations. It has been found that nanopipes are open core screw dislocations, and the population and size of the nanopipes is proportional to the Si doping concentration. Dislocation structures were found to depend on the Si doping level in the material, with higher Si doping giving a lower density of dislocations with a more random distribution. In addition some EELS, EDX and HRTEM have been performed on the nanopipes and dislocations in order to investigate Si segregation in the defects. In MBE grown GaN/In{sub 0.1}Ga{sub 0.9}N/GaN SQWs and MQWs, V shaped defects were found to be present in the InGaN regions, which locally reduced the width of the InGaN layers. (author)

  6. Transmission electron microscopy of defects and internal fields in GaN structures

    International Nuclear Information System (INIS)

    Mokhtari, H.

    2001-07-01

    The main aim of this study was to understand the microstructure of GaN and InGaN/GaN and to examine electric fields around the defects, and across the quantum wells by electron holography. For this reason different types of GaN and InGaN/GaN samples have been prepared and studied. Conventional transmission electron microscopy has been used for structural study of two MBE grown GaN/GaAs samples, grown at room temperature and at 340 deg C. The structure of the samples were found to be hexagonal polycrystalline in an amorphous GaN matrix, and textured hexagonal polycrystalline material respectively. The experimental results indicate that the higher growth temperature results in a more crystalline material with a higher density of bigger grain sizes. Different types of undoped and Si doped GaN/Sapphire samples were studied, with respect to the defect structure in GaN films. GaN was found to be a highly defective material with a dislocation density of 10 9 /cm 2 . The majority of the dislocations are edge dislocations. It has been found that nanopipes are open core screw dislocations, and the population and size of the nanopipes is proportional to the Si doping concentration. Dislocation structures were found to depend on the Si doping level in the material, with higher Si doping giving a lower density of dislocations with a more random distribution. In addition some EELS, EDX and HRTEM have been performed on the nanopipes and dislocations in order to investigate Si segregation in the defects. In MBE grown GaN/In 0.1 Ga 0.9 N/GaN SQWs and MQWs, V shaped defects were found to be present in the InGaN regions, which locally reduced the width of the InGaN layers. (author)

  7. Classification of defects in honeycomb composite structure of helicopter rotor blades

    International Nuclear Information System (INIS)

    Balasko, M.; Svab, E.; Molnar, Gy.; Veres, I.

    2005-01-01

    The use of non-destructive testing methods to qualify the state of rotor blades with respect to their expected flight hours, with the aim to extend their lifetime without any risk of breakdown, is an important financial demand. In order to detect the possible defects in the composite structure of Mi-8 and Mi-24 type helicopter rotor blades used by the Hungarian Army, we have performed combined neutron- and X-ray radiography measurements at the Budapest Research Reactor. Several types of defects were detected, analysed and typified. Among the most frequent and important defects observed were cavities, holes and or cracks in the sealing elements on the interface of the honeycomb structure and the section boarders. Inhomogeneities of the resin materials (resin-rich or starved areas) at the core-honeycomb surfaces proved to be an other important point. Defects were detected at the adhesive filling, and water percolation was visualized at the sealing interfaces of the honeycomb sections. Corrosion effects, and metal inclusions have also been detected

  8. Classification of defects in honeycomb composite structure of helicopter rotor blades

    Science.gov (United States)

    Balaskó, M.; Sváb, E.; Molnár, Gy.; Veres, I.

    2005-04-01

    The use of non-destructive testing methods to qualify the state of rotor blades with respect to their expected flight hours, with the aim to extend their lifetime without any risk of breakdown, is an important financial demand. In order to detect the possible defects in the composite structure of Mi-8 and Mi-24 type helicopter rotor blades used by the Hungarian Army, we have performed combined neutron- and X-ray radiography measurements at the Budapest Research Reactor. Several types of defects were detected, analysed and typified. Among the most frequent and important defects observed were cavities, holes and/or cracks in the sealing elements on the interface of the honeycomb structure and the section boarders. Inhomogeneities of the resin materials (resin-rich or starved areas) at the core-honeycomb surfaces proved to be an other important point. Defects were detected at the adhesive filling, and water percolation was visualized at the sealing interfaces of the honeycomb sections. Corrosion effects, and metal inclusions have also been detected.

  9. Structure and stability of defective silicene on Ag(001) and Ag(111) substrates: A computer experiment

    Science.gov (United States)

    Galashev, A. E.; Ivanichkina, K. A.; Vorob'ev, A. S.; Rakhmanova, O. R.

    2017-06-01

    The structure and stability of a two-layer defective silicene on Ag(001) and Ag(111) substrates have been investigated using the molecular dynamics method. The transformation of the radial distribution function of silicene due to the formation of monovacancies, divacancies, trivacancies, and hexavacancies is reduced primarily to a decrease in the intensity of the peaks and the disappearance of the "shoulder" in the second peak. With the passage of time, multivacancies can undergo coalescence with each other and the fragmentation into smaller vacancies, as well as form vacancy clusters. According to the geometric criterion, the Ag(001) substrate provides a higher stability of a perfect two-layer silicene. It has been found, however, that the defective silicene on this substrate has a lower energy only when it contains monovacancies and divacancies. A change in the size of defects leads to a change in the energy priority when choosing between the Ag(001) and Ag(111) substrates. The motion of a lithium ion inside an extended channel between two silicene sheets results in a further disordering of the defective structure of the silicene, during which the strongest stresses in the silicene are generated by forces directed perpendicular to the external electric field. These forces dominate in the silicene channel, the wall of which is supported by the Ag(001) or Ag(111) substrate.

  10. Stringy models of modified gravity: space-time defects and structure formation

    International Nuclear Information System (INIS)

    Mavromatos, Nick E.; Sakellariadou, Mairi; Yusaf, Muhammad Furqaan

    2013-01-01

    Starting from microscopic models of space-time foam, based on brane universes propagating in bulk space-times populated by D0-brane defects (''D-particles''), we arrive at effective actions used by a low-energy observer on the brane world to describe his/her observations of the Universe. These actions include, apart from the metric tensor field, also scalar (dilaton) and vector fields, the latter describing the interactions of low-energy matter on the brane world with the recoiling point-like space-time defect (D-particle). The vector field is proportional to the recoil velocity of the D-particle and as such it satisfies a certain constraint. The vector breaks locally Lorentz invariance, which however is assumed to be conserved on average in a space-time foam situation, involving the interaction of matter with populations of D-particle defects. In this paper we clarify the role of fluctuations of the vector field on structure formation and galactic growth. In particular we demonstrate that, already at the end of the radiation era, the (constrained) vector field associated with the recoil of the defects provides the seeds for a growing mode in the evolution of the Universe. Such a growing mode survives during the matter dominated era, provided the variance of the D-particle recoil velocities on the brane is larger than a critical value. We note that in this model, as a result of specific properties of D-brane dynamics in the bulk, there is no issue of overclosing the brane Universe for large defect densities. Thus, in these models, the presence of defects may be associated with large-structure formation. Although our string inspired models do have (conventional, from a particle physics point of view) dark matter components, nevertheless it is interesting that the role of ''extra'' dark matter is also provided by the population of massive defects. This is consistent with the weakly interacting character of the D-particle defects, which predominantly interact only

  11. THE DIGITAL VON FAHRENHEID PYRAMID

    Directory of Open Access Journals (Sweden)

    M. Bura

    2017-08-01

    Full Text Available 3D Scanners Lab from Digital Humanities Laboratory at the University of Warsaw initiated the scientific project, the purpose of which was to call attention to systematically penetrated and devastated pyramid-shaped tomb from the XVIII/XIX century, of family von Fahrenheid in Rapa in Banie Mazurskie commune (NE Poland. By conducting a series of non-invasive studies, such as 3D inventory using terrestrial laser scanning (TLS, thermal imaging, georadar measurements (around and inside the tomb and anthropological research of mummified remains as well - the complete dataset was collected. Through the integration of terrestrial (TLS and airborne laser scanning (ALS authors managed to analyse the surroundings of Fahrenheid pyriamid and influence of some objects (like trees on the condition and visibility of the Pyramids in the landscape.

  12. Deep Defect Detection within Thick Multilayer Aircraft Structures Containing Steel Fasteners Using a Giant-Magneto Resistive (GMR) Sensor (Preprint)

    National Research Council Canada - National Science Library

    Ko, Ray T; Steffes, Gary J

    2007-01-01

    Defect detection within thick multilayer structures containing steel fasteners is a challenging task in eddy current testing due to the magnetic permeability of the fasteners and overall thickness of the structure...

  13. Pyramidal-Reflector Solar Heater

    Science.gov (United States)

    1982-01-01

    Motor-driven reflector compensates for seasonal changes in Sun's altitude. System has flat-plate absorbers mounted on north side of attic interior. Skylight window on south-facing roof admits Sunlight into attic, lined with mirrors that reflect light to absorbers. Reflectors are inner surfaces of a pyramid lying on its side with window at its base and absorber plates in a cross-sectional plane near its apex.

  14. Analyzing the defect structure of CuO-doped PZT and KNN piezoelectrics from electron paramagnetic resonance.

    Science.gov (United States)

    Jakes, Peter; Kungl, Hans; Schierholz, Roland; Eichel, Rüdiger-A

    2014-09-01

    The defect structure for copper-doped sodium potassium niobate (KNN) ferroelectrics has been analyzed with respect to its defect structure. In particular, the interplay between the mutually compensating dimeric (Cu(Nb)'''-V(O)··) and trimeric (V(O)··-Cu(Nb)'''-V(O)··)· defect complexes with 180° and non-180° domain walls has been analyzed and compared to the effects from (Cu'' - V(O)··)(x)× dipoles in CuO-doped lead zirconate titanate (PZT). Attempts are made to relate the rearrangement of defect complexes to macroscopic electromechanical properties.

  15. Non-probabilistic defect assessment for structures with cracks based on interval model

    International Nuclear Information System (INIS)

    Dai, Qiao; Zhou, Changyu; Peng, Jian; Chen, Xiangwei; He, Xiaohua

    2013-01-01

    Highlights: • Non-probabilistic approach is introduced to defect assessment. • Definition and establishment of IFAC are put forward. • Determination of assessment rectangle is proposed. • Solution of non-probabilistic reliability index is presented. -- Abstract: Traditional defect assessment methods conservatively treat uncertainty of parameters as safety factors, while the probabilistic method is based on the clear understanding of detailed statistical information of parameters. In this paper, the non-probabilistic approach is introduced to the failure assessment diagram (FAD) to propose a non-probabilistic defect assessment method for structures with cracks. This novel defect assessment method contains three critical processes: establishment of the interval failure assessment curve (IFAC), determination of the assessment rectangle, and solution of the non-probabilistic reliability degree. Based on the interval theory, uncertain parameters such as crack sizes, material properties and loads are considered as interval variables. As a result, the failure assessment curve (FAC) will vary in a certain range, which is defined as IFAC. And the assessment point will vary within a rectangle zone which is defined as an assessment rectangle. Based on the interval model, the establishment of IFAC and the determination of the assessment rectangle are presented. Then according to the interval possibility degree method, the non-probabilistic reliability degree of IFAC can be determined. Meanwhile, in order to clearly introduce the non-probabilistic defect assessment method, a numerical example for the assessment of a pipe with crack is given. In addition, the assessment result of the proposed method is compared with that of the traditional probabilistic method, which confirms that this non-probabilistic defect assessment can reasonably resolve the practical problem with interval variables

  16. Non-probabilistic defect assessment for structures with cracks based on interval model

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Qiao; Zhou, Changyu, E-mail: changyu_zhou@163.com; Peng, Jian; Chen, Xiangwei; He, Xiaohua

    2013-09-15

    Highlights: • Non-probabilistic approach is introduced to defect assessment. • Definition and establishment of IFAC are put forward. • Determination of assessment rectangle is proposed. • Solution of non-probabilistic reliability index is presented. -- Abstract: Traditional defect assessment methods conservatively treat uncertainty of parameters as safety factors, while the probabilistic method is based on the clear understanding of detailed statistical information of parameters. In this paper, the non-probabilistic approach is introduced to the failure assessment diagram (FAD) to propose a non-probabilistic defect assessment method for structures with cracks. This novel defect assessment method contains three critical processes: establishment of the interval failure assessment curve (IFAC), determination of the assessment rectangle, and solution of the non-probabilistic reliability degree. Based on the interval theory, uncertain parameters such as crack sizes, material properties and loads are considered as interval variables. As a result, the failure assessment curve (FAC) will vary in a certain range, which is defined as IFAC. And the assessment point will vary within a rectangle zone which is defined as an assessment rectangle. Based on the interval model, the establishment of IFAC and the determination of the assessment rectangle are presented. Then according to the interval possibility degree method, the non-probabilistic reliability degree of IFAC can be determined. Meanwhile, in order to clearly introduce the non-probabilistic defect assessment method, a numerical example for the assessment of a pipe with crack is given. In addition, the assessment result of the proposed method is compared with that of the traditional probabilistic method, which confirms that this non-probabilistic defect assessment can reasonably resolve the practical problem with interval variables.

  17. Structure and defect studies of In2O3:Zn,Zr for higher stability TCO

    Science.gov (United States)

    Herwadkar, Aditi; Kim, Kwiseon

    2010-03-01

    The defects structures among the transparent conducting oxides (TCO) plays a major role in determining stability of the oxide over a temperature range and in tuning electrical and optical properties for the different TCO applications In2O3 crystallizes in the cubic bixbyite structure. The structure can be derived from the related fluorite structure by removing one fourth of the anions and allowing for small shifts of the ionic positions. In2O3 has two non-equivalent six-fold coordinated cation sites. For one of the sites, the cation is bounded by two structural vacancy along the body diagonal and for the other non-equivalent site the vacancies lie along the face diagonal. These vacancies are actually empty oxygen vacancy positions. Indium is in +3 charge state. ZnO on the other hand crystallizes to form wurtzite structure with four-fold coordination for Zn and is in +2 charge state where as the crystal structure of ZrO is rulite with Zr in +4 charge state and is four fold coordinated. Co-doping of Zn and Zr with each substituting the In atom satisfies the octet rule and is lower in energy then the individual substitutions with overall neutrality. The formation enthalpy as a function of pair (Zn, Zr) shows a minimum at experimental composition of In2(Zn,Zr)3O24. We in this work present the electronic structure optimization and study the defect states in this material.

  18. Was the Great Pyramid Built with Simple Machines?

    Science.gov (United States)

    Kraft, Susan; Poynor, Leslie

    2004-01-01

    Recently one of the authors challenged her third-grade students to use their imagination and travel with her to Egypt. As they were exploring the Great Pyramid, she encouraged the students to speculate how ancient people could have built such a massive structure without the sophisticated machinery they have at our disposal today. This article…

  19. Microstrip linear phase low pass filter based on defected ground structures for partial response modulation

    DEFF Research Database (Denmark)

    Cimoli, Bruno; Johansen, Tom Keinicke; Olmos, Juan Jose Vegas

    2018-01-01

    We report a high performance linear phase low pass filter (LPF) designed for partial response (PR) modulations. For the implementation, we adopted microstrip technology and a variant of the standard stepped‐impedance technique. Defected ground structures (DGS) are used for increasing the characte......We report a high performance linear phase low pass filter (LPF) designed for partial response (PR) modulations. For the implementation, we adopted microstrip technology and a variant of the standard stepped‐impedance technique. Defected ground structures (DGS) are used for increasing...... the characteristic impedance of transmission lines. Experimental results prove that the proposed filter can successfully modulate a non‐return‐to‐zero (NRZ) signal into a five levels PR one....

  20. Design and Analysis of a Triple Stop-band Filter Using Ratioed Periodical Defected Microstrip Structure

    Science.gov (United States)

    Jiang, Tao; Wang, Yanyan; Li, Yingsong

    2017-07-01

    In this paper, a triple stop-band filter with a ratioed periodical defected microstrip structure is proposed for wireless communication applications. The proposed ratioed periodical defected microstrip structures are spiral slots, which are embedded into a 50 Ω microstrip line to obtain multiple stop-bands. The performance of the proposed triple stop-band filter is investigated numerically and experimentally. Moreover, the equivalent circuit model of the proposed filter is also established and discussed. The results are given to verify that the proposed triple stop-band filter has three stop bands at 3.3 GHz, 5.2 GHz, 6.8 GHz to reject the unwanted signals, which is promising for integrating into UWB communication systems to efficiently prevent the potential interferences from unexpected narrowband signals such as WiMAX, WLAN and RFID communication systems.

  1. Localized Retinal Nerve Fiber Layer Defects in Red-free Photographs Versus En Face Structural Optical Coherence Tomography Images.

    Science.gov (United States)

    Jung, Jae Hoon; Park, Ji-Hye; Yoo, Chungkwon; Kim, Yong Yeon

    2018-03-01

    The purpose of this article is to compare the locations of localized retinal nerve fiber layer (RNFL) defects in red-free fundus photographs and optical coherence tomography (OCT) en face images. We performed a retrospective, comparative study on 46 eyes from 46 glaucoma patients with localized RNFL defects observed in red-free fundus photographs. En face structural images were obtained in the superficial and whole retinal layers using OCT and were overlaid on the corresponding red-free fundus photographs. The proximal/distal angular locations and angular width of each RNFL defect in red-free photos (red-free defects) and in en face structural images (en face defects) were compared. In the superficial retinal layer, there were no significant differences between red-free and en face defects on the proximal/distal angular location and angular width. In the whole retinal layer, the degree of the distal angular location of the en face defects was significantly larger than that of the red-free defects (71.85±18.26 vs. 70.87±17.90 degrees, P=0.003). The correlations of clinical variables with the differences in angular parameters between red-free and en face defects were not significant in the superficial retinal layer. The average RNFL thickness was negatively correlated with the difference in the distal angular location in the whole retinal layer (Pearson correlation coefficient=-0.401, P=0.006). Localized RNFL defects detected in OCT en face structural images of the superficial retinal layer showed high topographic correlation with defects detected in red-free photographs. OCT en face structural images in the superficial layer may be an alternative to red-free fundus photography for the identification of localized RNFL defects in glaucomatous eyes.

  2. Guided Bone Regeneration in Long-Bone Defects with a Structural Hydroxyapatite Graft and Collagen Membrane

    Science.gov (United States)

    2013-01-01

    Original Articles Guided Bone Regeneration in Long-Bone Defects with a Structural Hydroxyapatite Graft and Collagen Membrane Teja Guda, PhD,1,2 John...Joint Surg Br 90-B, 1617, 2008. 6. Carlo Reis, E.C., Borges AaPB, Araujo, M.V.F., Mendes, V.C., Guan, L., and Davies, J.E. Periodontal regeneration...Regeneration of periodontal tissues: combinations of barrier membranes and grafting materials–biological foundation and preclinical evi- dence: a

  3. Conference Analysis Report of Assessments on Defect and Damage for a High Temperature Structure

    International Nuclear Information System (INIS)

    Lee, Hyeong Yeon

    2008-11-01

    This report presents the analysis on the state-of-the-art research trends on creep-fatigue damage, defect assessment of high temperature structure, development of heat resistant materials and their behavior at high temperature based on the papers presented in the two international conferences of ASME PVP 2008 which was held in Chicago in July 2008 and CF-5(5th International Conference on Creep, Fatigue and Creep-Fatigue) which was held in Kalpakkam, India in September 2008

  4. Fine defective structure of silicon carbide powders obtained from different starting materials

    Directory of Open Access Journals (Sweden)

    Tomila T.V.

    2006-01-01

    Full Text Available The fine defective structure of silicon carbide powders obtained from silicic acid-saccharose, aerosil-saccharose, aerosil-carbon black, and hydrated cellulose-silicic acid gel systems was investigated. The relation between IR absorption characteristics and the microstructure of SiC particles obtained from different starting materials was established. The numerical relationship between the lattice parameter a and the frequency νTO is presented.

  5. Conference Analysis Report of Assessments on Defect and Damage for a High Temperature Structure

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hyeong Yeon

    2008-11-15

    This report presents the analysis on the state-of-the-art research trends on creep-fatigue damage, defect assessment of high temperature structure, development of heat resistant materials and their behavior at high temperature based on the papers presented in the two international conferences of ASME PVP 2008 which was held in Chicago in July 2008 and CF-5(5th International Conference on Creep, Fatigue and Creep-Fatigue) which was held in Kalpakkam, India in September 2008.

  6. Structural Defects in Donor-Acceptor Blends: Influence on the Performance of Organic Solar Cells

    Science.gov (United States)

    Sergeeva, Natalia; Ullbrich, Sascha; Hofacker, Andreas; Koerner, Christian; Leo, Karl

    2018-02-01

    Defects play an important role in the performance of organic solar cells. The investigation of trap states and their origin can provide ways to further improve their performance. Here, we investigate defects in a system composed of the small-molecule oligothiophene derivative DCV5T-Me blended with C60 , which shows power conversion efficiencies above 8% when used in a solar cell. From a reconstruction of the density of trap states by impedance spectroscopy, we obtain a Gaussian distribution of trap states with Et=470 meV below the electron transport level, Nt=8 ×1014 cm-3 , and σt=41 meV . From Voc vs illumination intensity and open-circuit corrected charge carrier extraction measurements, we find that these defects lead to trap-assisted recombination. Moreover, drift-diffusion simulations show that the trap states decrease the fill factor by 10%. By conducting degradation measurements and varying the blend ratio, we find that the observed trap states are structural defects in the C60 phase due to the distortion of the natural morphology induced by the mixing.

  7. Identification of equilibrium and irradiation-induced defects in nuclear ceramics: electronic structure calculations of defect properties and positron annihilation characteristics

    International Nuclear Information System (INIS)

    Wiktor, Julia

    2015-01-01

    During in-pile irradiation the fission of actinide nuclei causes the creation of large amounts of defects, which affect the physical and chemical properties of materials inside the reactor, in particular the fuel and structural materials. Positron annihilation spectroscopy (PAS) can be used to characterize irradiation induced defects, empty or containing fission products. This non-destructive experimental technique involves detecting the radiation generated during electron-positron annihilation in a sample and deducing the properties of the material studied. As positrons get trapped in open volume defects in solids, by measuring their lifetime and momentum distributions of the annihilation radiation, one can obtain information on the open and the chemical environments of the defects. In this work electronic structure calculations of positron annihilation characteristics were performed using two-component density functional theory (TCDFT). To calculate the momentum distributions of the annihilation radiation, we implemented the necessary methods in the open-source ABINIT program. The theoretical results have been used to contribute to the identification of the vacancy defects in two nuclear ceramics, silicon carbide (SiC) and uranium dioxide (UO 2 ). (author) [fr

  8. Acousto-defect interaction in irradiated and non-irradiated silicon n+-p structures

    Science.gov (United States)

    Olikh, O. Ya.; Gorb, A. M.; Chupryna, R. G.; Pristay-Fenenkov, O. V.

    2018-04-01

    The influence of ultrasound on current-voltage characteristics of non-irradiated silicon n+-p structures as well as silicon structures exposed to reactor neutrons or 60Co gamma radiation has been investigated experimentally. It has been found that the ultrasound loading of the n+-p structure leads to the reversible change of shunt resistance, carrier lifetime, and ideality factor. Specifically, considerable acoustically induced alteration of the ideality factor and the space charge region lifetime was observed in the irradiated samples. The experimental results were described by using the models of coupled defect level recombination, Shockley-Read-Hall recombination, and dislocation-induced impedance. The experimentally observed phenomena are associated with the increase in the distance between coupled defects as well as the extension of the carrier capture coefficient of complex point defects and dislocations. It has been shown that divacancies and vacancy-interstitial oxygen pairs are effectively modified by ultrasound in contrast to interstitial carbon-interstitial oxygen complexes.

  9. A Design of a Terahertz Microstrip Bandstop Filter with Defected Ground Structure

    Directory of Open Access Journals (Sweden)

    Arjun Kumar

    2013-01-01

    Full Text Available A planar microstrip terahertz (THz bandstop filter has been proposed with defected ground structure with high insertion loss (S21 in a stopband of −25.8 dB at 1.436 THz. The parameters of the circuit model have been extracted from the EM simulation results. A dielectric substrate of Benzocyclobutene (BCB is used to realize a compact bandstop filter using modified hexagonal dumbbell-shape defected ground structure (DB-DGS. In this paper, a defected ground structure topology is used in a λ/4, 50 Ω microstrip line at THz frequency range for compactness. No article has been reported on the microstrip line at terahertz frequency regime using DGS topology. The proposed filter can be used for sensing and detection in biomedical instruments in DNA testing. All the simulations/cosimulations are carried out using a full-wave EM simulator CST V.9 Microwave Studio, HFSS V.10, and Agilent Design Suite (ADS.

  10. Intrinsic point defects in zinc oxide. Modeling of structural, electronic, thermodynamic and kinetic properties

    Energy Technology Data Exchange (ETDEWEB)

    Erhart, P.

    2006-07-01

    The present dissertation deals with the modeling of zinc oxide on the atomic scale employing both quantum mechanical as well as atomistic methods. The first part describes quantum mechanical calculations based on density functional theory of intrinsic point defects in ZnO. To begin with, the geometric and electronic structure of vacancies and oxygen interstitials is explored. In equilibrium oxygen interstitials are found to adopt dumbbell and split interstitial configurations in positive and negative charge states, respectively. Semi-empirical self-interaction corrections allow to improve the agreement between the experimental and the calculated band structure significantly; errors due to the limited size of the supercells can be corrected by employing finite-size scaling. The effect of both band structure corrections and finite-size scaling on defect formation enthalpies and transition levels is explored. Finally, transition paths and barriers for the migration of zinc as well as oxygen vacancies and interstitials are determined. The results allow to interpret diffusion experiments and provide a consistent basis for developing models for device simulation. In the second part an interatomic potential for zinc oxide is derived. To this end, the Pontifix computer code is developed which allows to fit analytic bond-order potentials. The code is subsequently employed to obtain interatomic potentials for Zn-O, Zn-Zn, and O-O interactions. To demonstrate the applicability of the potentials, simulations on defect production by ion irradiation are carried out. (orig.)

  11. Theoretical study using electronic structure calculations of uranium and cerium dioxides containing defects and impurities

    International Nuclear Information System (INIS)

    Shi, Lei

    2016-01-01

    Uranium dioxide (UO_2) is the most widely used nuclear fuel in existing nuclear reactors around the world. While in service for energy supply, UO_2 is submitted to the neutron flux and undergoes nuclear fission chain reactions, which create large number of fission products and point defects. The study of the behavior of the fission products and point defects is important to understand the fuel properties under irradiation. We conduct electronic structure calculations based on the density functional theory (DFT) to model this radiation damage at the atomic scale. The DFT+U method is used to describe the strong correlation of the 4f electrons of cerium and 5f electrons of uranium in the materials studied (UO_2, CeO_2 and (U, Ce)O_2). (U, Ce)O_2 is studied because it is considered as a low radioactive model material of mixed actinide oxides such as the MOX fuel (U, Pu)O_2 used in light water reactors and fast neutron reactors. Cerium dioxide (CeO_2) is studied to provide reference data of (U, Ce)O_2. We perform a DFT+U study of point defects and gaseous fission products (Xe and Kr) in CeO_2 and compare our results to the existing ones of UO_2. We study the bulk properties as well as the behavior of defects for (U, Ce)O_2, and compare our results to the ones of (U, Pu)O_2. Furthermore, for the study of defects in UO_2, methodological improvements are explored considering the spin-orbit coupling effect and the finite-size effect of the simulation supercell. (author) [fr

  12. Identifying Structural Flow Defects in Disordered Solids Using Machine-Learning Methods

    Science.gov (United States)

    Cubuk, E. D.; Schoenholz, S. S.; Rieser, J. M.; Malone, B. D.; Rottler, J.; Durian, D. J.; Kaxiras, E.; Liu, A. J.

    2015-03-01

    We use machine-learning methods on local structure to identify flow defects—or particles susceptible to rearrangement—in jammed and glassy systems. We apply this method successfully to two very different systems: a two-dimensional experimental realization of a granular pillar under compression and a Lennard-Jones glass in both two and three dimensions above and below its glass transition temperature. We also identify characteristics of flow defects that differentiate them from the rest of the sample. Our results show it is possible to discern subtle structural features responsible for heterogeneous dynamics observed across a broad range of disordered materials.

  13. Diffuse scattering and defect structure simulations a cook book using the program DISCUS

    CERN Document Server

    Neder, Reinhard B

    2009-01-01

    In recent years it has become apparent that knowing the average atomic structure of materials is insufficient to understand their properties. Diffuse scattering in addition to the Bragg scattering holds the key to learning about defects in materials, the topic of many recent books. What has been missing is a detailed step-by-step guide how to simulate disordered materials. The DISCUS cook book fills this need covering simple topics such as building a computer crystal to complextopic such as domain structures, stacking faults or using advanced refinement techniques to adjust parameters on a dis

  14. Structural defects in multiferroic BiMnO3 studied by transmission electron microscopy and electron energy-loss spectroscopy

    International Nuclear Information System (INIS)

    Yang, H.; Chi, Z. H.; Yao, L. D.; Zhang, W.; Li, F. Y.; Jin, C. Q.; Yu, R. C.

    2006-01-01

    The multiferroic material BiMnO 3 synthesized under high pressure has been systematically studied by transmission electron microscopy and electron energy-loss spectroscopy, and some important structural defects are revealed in this multiferroic material. The frequently observed defects are characterized to be Σ3(111) twin boundaries, Ruddlesden-Popper [Acta Crystallogr. 11, 54 (1958)] antiphase boundaries, and a p p superdislocations connected with a small segment of Ruddlesden-Popper defect. These defects are present initially in the as-synthesized sample. In addition, we find that ordered voids (oxygen vacancies) are easily introduced into the multiferroic BiMnO 3 by electron-beam irradiation

  15. Experimental and theoretical investigation of lattice defect structures in a series of Zn, Fe-doped nonstoichiometric lithium niobate

    International Nuclear Information System (INIS)

    Guo Fengyun; Lue Qiang; Sun Liang; Li Hongtao; Zhen Xihe; Xu Yuheng; Zhao Liancheng

    2006-01-01

    A series of the double doped lithium niobate (LiNbO 3 , LN) single crystals had been grown by Czochralski method. The Curie temperatures of various concentrations doped or [Li]/[Nb] ratio LN crystals measured by differential thermal analysis (DTA) were discussed to investigate their defect structures with Safaryan et al. new approach about LN lattice defect structure using Curie temperatures calculated. Infrared transmission spectra of various concentrations doped were used to compare the investigation above. The results show that the lithium vacancy model is the more probable to describe the lattice defect structure of the doped LN single crystal

  16. Study of defects and vacancies in structural properties of Mn, co-doped oxides: ZnO

    Science.gov (United States)

    Kumar, Harish; Kaushik, A.; Alvi, P. A.; Dalela, B.; Dalela, S.

    2018-05-01

    The paper deals with the Structural properties on Mn, Co doped oxides ZnO samples using XRD, Positron Annihilation Lifetime (PAL) Spectra and Raman Spectra. The Mn, Co doped ZnO samples crystallize in a wurtzite structure without any impurity phases in XRD Spectra. The defect state of these samples has been investigated by using positron annihilation lifetime (PAL) spectroscopy technique in which all the relevant lifetime parameters are measured for all the spectra. The results are explained in the direction of doping concentration in these samples in terms of defects structure on Zn lattice site VZn and oxygen defects Vo.

  17. Defect structure, nonstoichiometry, and phase stability of Ca-doped YCrO3

    International Nuclear Information System (INIS)

    Carini, G.F. II; Anderson, H.U.; Nasrallah, M.M.; Sparlin, D.M.

    1991-01-01

    The dependence of the defect structure of Ca-doped YCrO 3 on oxygen activity and temperature was investigated by high temperature thermogravimetric measurements. Defect models developed from electrical conductivity data obtained in a previous study were used to interpret the thermogravimetric data. A correlation was found between the electrical conductivity and the thermogravimetric data which suggested that these data were concomitantly dependent on the acceptor dopant and oxygen vacancy dependence of the thermodynamic parameters. Kroeger-Vink type diagrams showing the regions of stability with respect to oxygen activity and temperature were constructed. The TGA data show that Ca-doped YCrO 3 is even more stable toward reduction than doped LaCrO 3

  18. DEEP LEARNING AND IMAGE PROCESSING FOR AUTOMATED CRACK DETECTION AND DEFECT MEASUREMENT IN UNDERGROUND STRUCTURES

    Directory of Open Access Journals (Sweden)

    F. Panella

    2018-05-01

    Full Text Available This work presents the combination of Deep-Learning (DL and image processing to produce an automated cracks recognition and defect measurement tool for civil structures. The authors focus on tunnel civil structures and survey and have developed an end to end tool for asset management of underground structures. In order to maintain the serviceability of tunnels, regular inspection is needed to assess their structural status. The traditional method of carrying out the survey is the visual inspection: simple, but slow and relatively expensive and the quality of the output depends on the ability and experience of the engineer as well as on the total workload (stress and tiredness may influence the ability to observe and record information. As a result of these issues, in the last decade there is the desire to automate the monitoring using new methods of inspection. The present paper has the goal of combining DL with traditional image processing to create a tool able to detect, locate and measure the structural defect.

  19. Synthesis, characterization, X-ray crystal structure and conductometry studying of a number of new Schiff base complexes; a new example of binuclear square pyramidal geometry of Cu(II) complex bridged with an oxo group

    Science.gov (United States)

    Golbedaghi, Reza; Alavipour, Ehsan

    2015-11-01

    Three new binuclear Cu(II), Mn(II), Co(II) complexes [Cu2(L) (ClO4)](ClO4)2 (1), [Mn2(L) (ClO4)](ClO4)2 (2), and [Co2(L) (ClO4)](ClO4)2 (3), {L = 1,3-bis(2-((Z)-(2-aminopropylimino)methyl)phenoxy)propan-2-ol} have been synthesized. Single crystal X-ray structure analysis of complex 1 showed that the complex is binuclear and all nitrogen and oxygen atoms of ligand (N4O3) are coordinated to two Cu(II) center ions. In addition, the crystal structure studying shows, a perchlorate ion has been bridged to the Cu(II) metal centers. However, two distorted square pyramidal Cu(II) ions are bridged asymmetrically by a perchlorate ion and oxygen of hydroxyl group of Schiff base ligand. In addition, the conductometry behaviors of all complexes were studied in acetonitrile solution.

  20. Structural and optical studies on mesoscopic defect structure in highly conductive AgI-ZnO composites

    International Nuclear Information System (INIS)

    Fujishiro, Fumito; Mochizuki, Shosuke

    2003-01-01

    The electrical conductivity of (x)AgI-(1-x)ZnO (0≤x≤1) composites at room temperature increases with increasing AgI content and reaches a maximum at about 50% AgI. The results obtained by the scanning electron microscopy, X-ray diffractometry and photoluminescence spectroscopy have clarified high-ionic-conduction pathways related to mesoscopic defect structure at AgI/ZnO interfaces and mesoscopically disordered structure in AgI domain. We have observed also new optical phenomenon, which may arise from excitation energy transfer between AgI-exciton and photoinduced oxygen vacancy at the AgI/ZnO interface

  1. New structural and functional defects in polyphosphate deficient bacteria: A cellular and proteomic study

    Directory of Open Access Journals (Sweden)

    Chávez Francisco P

    2010-01-01

    Full Text Available Abstract Background Inorganic polyphosphate (polyP, a polymer of tens or hundreds of phosphate residues linked by ATP-like bonds, is found in all organisms and performs a wide variety of functions. PolyP is synthesized in bacterial cells by the actions of polyphosphate kinases (PPK1 and PPK2 and degraded by exopolyphosphatase (PPX. Bacterial cells with polyP deficiencies due to knocking out the ppk1 gene are affected in many structural and important cellular functions such as motility, quorum sensing, biofilm formation and virulence among others. The cause of this pleiotropy is not entirely understood. Results The overexpression of exopolyphosphatase in bacteria mimicked some pleitropic defects found in ppk1 mutants. By using this approach we found new structural and functional defects in the polyP-accumulating bacteria Pseudomonas sp. B4, which are most likely due to differences in the polyP-removal strategy. Colony morphology phenotype, lipopolysaccharide (LPS structure changes and cellular division malfunction were observed. Finally, we used comparative proteomics in order to elucidate the cellular adjustments that occurred during polyP deficiency in this bacterium and found some clues that helped to understand the structural and functional defects observed. Conclusions The results obtained suggest that during polyP deficiency energy metabolism and particularly nucleoside triphosphate (NTP formation were affected and that bacterial cells overcame this problem by increasing the flux of energy-generating metabolic pathways such as tricarboxilic acid (TCA cycle, β-oxidation and oxidative phosphorylation and by reducing energy-consuming ones such as active transporters and amino acid biosynthesis. Furthermore, our results suggest that a general stress response also took place in the cell during polyP deficiency.

  2. Characterizing the relationship between hyperstoichiometry, defect structure and local corrosion kinetics of uranium dioxide

    International Nuclear Information System (INIS)

    He Heming; Qin, Z.; Shoesmith, D.W.

    2010-01-01

    The ability of the UO 2 fluorite structure to accommodate large amounts of interstitial oxygen in various lattice sites leads to the formation of hyper-stoichiometric phases. The defect structures occurring in hyper-stoichiometric UO 2+x over the range 0.02 ≤ x ≤ 0.1 have been characterized by SEM/EDX and Raman analyses. The results demonstrate that as the nominal stoichiometry increases from 2.002 to 2.1, the diversity of defective structures existing on the UO 2+ surface also increases. Scanning electrochemical microscopy (SECM) measurements combined with a theoretical model were used to determine the rate constant for the reduction of the redox mediator ferrocene methanol, acting as a cathodic oxidant to corrode the four UO 2+x specimens. The rate constant was found to vary with location on the surface. Stoichiometric locations, with a well defined fluorite structure, exhibited very low corrosion rates. Higher rates were observed at more non-stoichiometric locations with the highest rates being obtained on locations exhibiting tetragonal distortions as their composition approached UO 2.33 . The distribution of rates increases with the degree of nominal non-stoichiometry as the diversity of microstructures existing on the UO 2+x surface increases.

  3. Pyramiding for Resistance Durability: Theory and Practice.

    Science.gov (United States)

    Mundt, Chris

    2018-04-12

    Durable disease resistance is a key component of global food security, and combining resistance genes into "pyramids" is an important way to increase durability of resistance. The mechanisms by which pyramids impact durability are not well known. The traditional view of resistance pyramids considers the use of major resistance gene (R-gene) combinations deployed against pathogens that are primarily asexual. Interestingly, published examples of the successful use of pyramids in the traditional sense are rare. In contrast, most published descriptions of durable pyramids in practice are for cereal rusts, and tend to indicate an association between durability and cultivars combining major R-genes with incompletely expressed, adult plant resistance genes. Pyramids have been investigated experimentally for a diversity of pathogens, and many reduce disease levels below that of the single best gene. Resistance gene combinations have been identified through phenotypic reactions, molecular markers, and challenge against effector genes. As resistance genes do not express equally in all genetic backgrounds, however, a combination of genetic information and phenotypic analyses provide the ideal scenario for testing of putative pyramids. Not all resistance genes contribute equally to pyramids, and approaches have been suggested to identify the best genes and combinations of genes for inclusion. Combining multiple resistance genes into a single plant genotype quickly is a challenge that is being addressed through alternative breeding approaches, as well as through genomics tools such as resistance gene cassettes and gene editing. Experimental and modeling tests of pyramid durability are in their infancy, but have promise to help direct future studies of pyramids. Several areas for further work on resistance gene pyramids are suggested.

  4. Antisite Defects of the L12 Structure Determined by the Phase Field Microelasticity Model

    International Nuclear Information System (INIS)

    Jing, Zhang; Zheng, Chen; Yan-Li, Lu; Yong-Xin, Wang; Yan, Zhao

    2009-01-01

    A phase field microelasticity simulation is performed to examine the antisite defect of L1 2 -Ni 3 Al in Ni 75 Al 5.3 V 19.7 ternary alloy. Combinimg strain energy with the phase field model leads to an atom configuration change as time proceeds. For the Ni sublattice, the antisite defect Al Ni , the equilibrium occupancy probability (OP) of which declines, precedes Ni Ni and V Ni in reaching equilibrium; subsequently, Ni Ni and V Ni present a phenomenon of symmetrical rise and decline individually. Similarly, for the Al sublattice, the antisite defect Ni Al , the OP of which eventually rises, takes fewer time steps than Al Ai and V Al to attain equilibrium. Thereafter, Al Al rises while V Al declines symmetrically at the axes of the Ni Al MAI curve. Furthermore, the OP for the Al sublattice is much more sensitive to strain energy than that for the Ni sublattice. (condensed matter: structure, mechanical and thermal properties)

  5. Structural and optical investigations of oxygen defects in zinc oxide nanoparticles

    International Nuclear Information System (INIS)

    Sahai, Anshuman; Goswami, Navendu

    2015-01-01

    ZnO nanoparticles (NPs) were prepared implementing chemical precipitation method. Structural and optical characterizations of synthesized ZnO NPs were thoroughly probed applying X-ray diffraction (XRD), transmission electron microscope (TEM), energy dispersive X-ray (EDX) analysis, X-ray photoelectron spectroscopy (XPS), UV- Visible absorption and fluorescence (FL) spectroscopy. The XRD and TEM analyses revealed hexagonal wurtzite phase with 25-30 nm size. EDX analysis indicated oxygen (O) rich composition of nanoparticles. In accordance with EDX, XPS analysis verifies O i rich stoichiometry of prepared NPs. Furthermore, concurrence of lattice oxygen (O L ), interstitial oxygen (O i ) and oxygen vacancy (V O ) in ZnO NPs was demonstrated through XPS analysis. Size quantization of nanoparticles is evident by blue shift of UV-Visible absorption energy. The FL spectroscopic investigations ascertain the existence of several discrete and defect states and radiative transitions occurring therein. Display of visible emission from oxygen defect states and most importantly, excess of O i defects in prepared ZnO nanoparticles, was well established through FL study

  6. Analysis of structure and defects in thin silicon films deposited from hydrogen diluted silane

    International Nuclear Information System (INIS)

    Elzakker, G. van; Nadazdy, V.; Tichelaar, F.D.; Metselaar, J.W.; Zeman, M.

    2006-01-01

    Thin silicon layers have been deposited from silane diluted with hydrogen. The dilution ratio R (R = [H 2 ]/[SiH 4 ]) has been varied between R = 0 and R = 40. The structural properties of Si:H films have been studied using transmission electron microscopy imaging and Raman spectroscopy. The phase evolution from the amorphous phase into the mixed and eventually microcrystalline phase strongly depends on the hydrogen dilution. The initiation of the microcrystalline growth occurs between R = 20 and R = 25. The phase transition becomes more abrupt with increasing hydrogen dilution. Optoelectronic properties of the layers have been determined. Increasing hydrogen dilution results in films with increasing effective defect density and Urbach energy, which is related to inhomogeneous growth. The charge deep-level transient spectroscopy technique (Q-DLTS) was applied for the first time on hydrogen diluted thin silicon films in order to investigate the energy distribution of the defect states in these layers as a function of the dilution ratio R. The Q-DLTS spectra indicate a difference in defect-state distribution when the films evolve from the amorphous phase into the microcrystalline phase

  7. Influences of Stone–Wales defects on the structure, stability and electronic properties of antimonene: A first principle study

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Yonghong, E-mail: hchyh2001@tom.com [School of Nuclear Technology and Chemistry & Biology, Hubei University of Science and Technology, Xianning 437100 (China); Wu, Yunyi [Department of Energy Materials and Technology, General Research Institute for Nonferrous Metals, Beijing (China); Zhang, Shengli [Institute of Optoelectronics & Nanomaterials, Herbert Gleiter Institute of Nanoscience, College of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China)

    2016-12-15

    Defects are inevitably present in materials, and their existence strongly affects the fundamental physical properties of 2D materials. Here, we performed first-principles calculations to study the structural and electronic properties of antimonene with Stone–Wales defects, highlighting the differences in the structure and electronic properties. Our calculations show that the presence of a SW defect in antimonene changes the geometrical symmetry. And the band gap decreases in electronic band structure with the decrease of the SW defect concentration. The formation energy and cohesive energy of a SW defect in antimonene are studied, showing the possibility of its existence and its good stability, respectively. The difference charge density near the SW defect is explored, by which the structural deformations of antimonene are explained. At last, we calculated the STM images for the SW defective antimonene to provide more information and characters for possible experimental observation. These results may provide meaningful references to the development and design of novel nanodevices based on new 2D materials.

  8. Defect structure of TiS{sub 3} single crystals of the A-ZrSe{sub 3} type

    Energy Technology Data Exchange (ETDEWEB)

    Bolotina, N. B., E-mail: nb-bolotina@mail.ru [Russian Academy of Sciences, Shubnikov Institute of Crystallography, Federal Scientific Research Centre “Crystallography and Photonics,” (Russian Federation); Gorlova, I. G. [Russian Academy of Sciences, Kotel’nikov Institute of Radioengineering and Electronics (Russian Federation); Verin, I. A. [Russian Academy of Sciences, Shubnikov Institute of Crystallography, Federal Scientific Research Centre “Crystallography and Photonics,” (Russian Federation); Titov, A. N. [Russian Academy of Sciences, Mikheev Institute of Metal Physics, Ural Branch (Russian Federation); Arakcheeva, A. V. [Phase Solutions, Co Ltd. (Switzerland)

    2016-11-15

    The defect structure of TiS{sub 3} single crystals of the A-ZrSe{sub 3} type has been determined based on X-ray diffraction data. Shear defects manifest themselves as displacements of ab layers (which can imitate a twin) by ∼0.5a. Regular shears facilitate the formation of a superstructure along the c axis. A model of defect in the layer structure is proposed to explain the atomic displacements at an angle to the layer plane.

  9. Morphological pyramids in multiresolution MIP rendering of large volume data : Survey and new results

    NARCIS (Netherlands)

    Roerdink, J.B.T.M.

    We survey and extend nonlinear signal decompositions based on morphological pyramids, and their application to multiresolution maximum intensity projection (MIP) volume rendering with progressive refinement and perfect reconstruction. The structure of the resulting multiresolution rendering

  10. The cradle of pyramids in satellite images

    OpenAIRE

    Sparavigna, Amelia Carolina

    2011-01-01

    We propose the use of image processing to enhance the Google Maps of some archaeological areas of Egypt. In particular we analyse that place which is considered the cradle of pyramids, where it was announced the discovery of a new pyramid by means of an infrared remote sensing.

  11. Defect-driven interfacial electronic structures at an organic/metal-oxide semiconductor heterojunction.

    Science.gov (United States)

    Winget, Paul; Schirra, Laura K; Cornil, David; Li, Hong; Coropceanu, Veaceslav; Ndione, Paul F; Sigdel, Ajaya K; Ginley, David S; Berry, Joseph J; Shim, Jaewon; Kim, Hyungchui; Kippelen, Bernard; Brédas, Jean-Luc; Monti, Oliver L A

    2014-07-16

    The electronic structure of the hybrid interface between ZnO and the prototypical organic semiconductor PTCDI is investigated via a combination of ultraviolet and X-ray photoelectron spectroscopy (UPS/XPS) and density functional theory (DFT) calculations. The interfacial electronic interactions lead to a large interface dipole due to substantial charge transfer from ZnO to 3,4,9,10-perylenetetracarboxylicdiimide (PTCDI), which can be properly described only when accounting for surface defects that confer ZnO its n-type properties. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Morphology, deformation, and defect structures of TiCr2 in Ti-Cr alloys

    International Nuclear Information System (INIS)

    Chen, K.C.; Allen, S.M.; Livingston, J.D.

    1992-01-01

    The morphologies and defect structures of TiCr 2 in several Ti-Cr alloys have been examined by optical metallography, x-ray diffraction, and transmission electron microscopy (TEM), in order to explore the room-temperature deformability of the Laves phase TiCr 2 . The morphology of the Laves phase was found to be dependent upon alloy composition and annealing temperature. Samples deformed by compression have also been studied using TEM. Comparisons of microstructures before and after deformation suggest an increase in twin, stacking fault, and dislocation density within the Laves phase, indicating some but not extensive room-temperature deformability

  13. Defect Structure of High-Temperature-Grown GaMnSb/GaSb

    International Nuclear Information System (INIS)

    Romanowski, P.; Bak-Misiuk, J.; Dynowska, E.; Domagala, J.Z.; Wojciechowski, T.; Jakiela, R.; Sadowski, J.; Barcz, A.; Caliebe, W.

    2010-01-01

    GaMnSb/GaSb(100) layers with embedded MnSb inclusions have been grown at 720 K using MBE technique. This paper presents the investigation of the defect structure of Ga1-xMnxSb layers with different content of manganese (up to x = 0.07). X-ray diffraction method using conventional and synchrotron radiation was applied. Dimensions and shapes of inclusions were detected by scanning electron microscopy. Depth profiles of elements were measured using secondary ion mass spectroscopy technique. (authors)

  14. Evolution of MBE HgCdTe defect structure studied with ion milling method

    Directory of Open Access Journals (Sweden)

    Pociask-Bialy Malgorzata

    2017-01-01

    Full Text Available In this paper, is shown how ion milling can assist in assessing the defect structure of MCT by revealing the residual doping, and establishing the minimum level of donor concentration Nmd, which is needed for obtaining n-regions with a reproducible n value. For this purpose, a study of the electrical properties of ion-milled LWIR n-type MCT films, un-doped and doped with indium with the concentration NIn = 5 × 1014–1017 cm−3 is proposed.

  15. Role of masking oxide on silicon in processes of defect generation at formation of SIMOX structures

    CERN Document Server

    Askinazi, A Y; Miloglyadova, L V

    2002-01-01

    One investigated into Si-SiO sub 2 structures formed by implantation of oxygen ions into silicon (SIMOX-technology) by means of techniques based on measuring of high-frequency volt-farad characteristics and by means of electroluminescence. One determined existence of electrically active centres and of luminescence centres in the formed oxide layer near boundary with silicon. One clarified the role SiO sub 2 masking layer in silicon in defect generation under formation of the masked oxide layer. One established dependence of concentration of electrically active and luminescence centres on thickness of masking layer

  16. Tuning the band structure of graphene nanoribbons through defect-interaction-driven edge patterning

    Science.gov (United States)

    Du, Lin; Nguyen, Tam N.; Gilman, Ari; Muniz, André R.; Maroudas, Dimitrios

    2017-12-01

    We report a systematic analysis of pore-edge interactions in graphene nanoribbons (GNRs) and their outcomes based on first-principles calculations and classical molecular-dynamics simulations. We find a strong attractive interaction between nanopores and GNR edges that drives the pores to migrate toward and coalesce with the GNR edges, which can be exploited to form GNR edge patterns that impact the GNR electronic band structure and tune the GNR band gap. Our analysis introduces a viable physical processing strategy for modifying GNR properties by combining defect engineering and thermal annealing.

  17. Computer simulation and implementation of defected ground structure on a microstrip antenna

    Science.gov (United States)

    Adrian, H.; Rambe, A. H.; Suherman

    2018-03-01

    Defected Ground Structure (DGS) is a method reducing etching area on antenna ground to form desirable antenna’s ground field. This paper reports the method impact on microstrip antennas working on 1800 and 2400 MHz. These frequencies are important as many radio network applications such mobile phones and wireless devices working on these channels. The assessments were performed by simulating and fabricating the evaluated antennas. Both simulation data and implementation measurements show that DGS successfully improves antenna performances by increasing bandwidth up to 19%, reducing return loss up to 109% and increasing gain up to 33%.

  18. Thermal annealing of carbon nanotubes reveals a toxicological impact of the structural defects

    Energy Technology Data Exchange (ETDEWEB)

    Figarol, Agathe, E-mail: figarol@emse.fr [Ecole Nationale Supérieure des Mines, SPIN-EMSE, CNRS: UMR 5307, LGF (France); Pourchez, Jérémie, E-mail: pourchez@emse.fr [Ecole Nationale Supérieure des Mines, CIS-EMSE, EA 4624, SFR IFRESIS, LINA (France); Boudard, Delphine [Université Jean Monnet Saint-Etienne, EA 4624, SFR IFRESIS, LINA (France); Forest, Valérie [Ecole Nationale Supérieure des Mines, CIS-EMSE, EA 4624, SFR IFRESIS, LINA (France); Berhanu, Sarah [Armines - Mines ParisTech, Centre des Matériaux, CNRS UMR 7633 (France); Tulliani, Jean-Marc [Politecnico di Torino, Department of Applied Science and Technology (Italy); Lecompte, Jean-Pierre [Centre Européen de la céramique CNRS: UMR 7315, SPCTS (France); Cottier, Michèle [Université Jean Monnet Saint-Etienne, EA 4624, SFR IFRESIS, LINA (France); Bernache-Assollant, Didier [Ecole Nationale Supérieure des Mines, CIS-EMSE, EA 4624, SFR IFRESIS, LINA (France); Grosseau, Philippe [Ecole Nationale Supérieure des Mines, SPIN-EMSE, CNRS: UMR 5307, LGF (France)

    2015-04-15

    The biological response to pristine and annealed multi-walled carbon nanotubes (MWCNT) was assessed on murine macrophages (RAW 264.7). First, the physicochemical features of the as-produced MWCNT and annealed at 2125 °C for 1 h were fully characterized. A decrease in structural defects, hydrophobicity and catalytic impurities was detected after annealing. Thereafter, their impact on cytotoxicity, oxidative stress, and pro-inflammatory response was investigated at concentrations ranging from 15 to 120 µg mL{sup −1}. No effect of the 2125 °C treatment was detected on the cytotoxicity. In contrast, the annealed carbon nanotubes showed a significant increase of the pro-inflammatory response. We assumed that this behavior was due to the reduction in structural defects that may modify the layer of adsorbed biomolecules. Surprisingly, the purification of metallic catalysts did not have any significant impact on the oxidative stress. We suggested that the structural improvements from the 2125 °C treatment can decrease the carbon nanotube scavenging capacity and thus allow a higher free radical release which may counterbalance the decrease of oxidative stress due to a lower content of metallic impurities.

  19. A Compact Wideband Dual-Polarized Antenna with Harmonic Suppression Using Nonuniform Defected Ground Structure

    Directory of Open Access Journals (Sweden)

    Lana Damaj

    2015-01-01

    Full Text Available A wideband dual-polarized coplanar waveguide (CPW fed antenna integrating a wide stop-band filter is presented. The designed filter is based on a nonuniform defected ground structure (DGS in order to obtain a wide stop-band and a compact size. This filter is used to reject harmonics and spurious radiation arising from the RF front end. The complete structure (antenna and filter has been optimized to have a compact size of 0.6×0.6λ02 (λ0 being the free-space wavelength at the lowest operating frequency. The realized antenna operates in the frequency range between 2.7 GHz and 5.9 GHz (bandwidth of about 74%. The isolation between feeding ports is more than 18 dB. The complete structure has a wide stop-band characteristic (103% for harmonic rejection. The simulated numerical results have been confirmed with measurements.

  20. Evidence for Kinetic Limitations as a Controlling Factor of Ge Pyramid Formation: a Study of Structural Features of Ge/Si(001) Wetting Layer Formed by Ge Deposition at Room Temperature Followed by Annealing at 600 °C.

    Science.gov (United States)

    Storozhevykh, Mikhail S; Arapkina, Larisa V; Yuryev, Vladimir A

    2015-12-01

    The article presents an experimental study of an issue of whether the formation of arrays of Ge quantum dots on the Si(001) surface is an equilibrium process or it is kinetically controlled. We deposited Ge on Si(001) at the room temperature and explored crystallization of the disordered Ge film as a result of annealing at 600 °C. The experiment has demonstrated that the Ge/Si(001) film formed in the conditions of an isolated system consists of the standard patched wetting layer and large droplike clusters of Ge rather than of huts or domes which appear when a film is grown in a flux of Ge atoms arriving on its surface. We conclude that the growth of the pyramids appearing at temperatures greater than 600 °C is controlled by kinetics rather than thermodynamic equilibrium whereas the wetting layer is an equilibrium structure. Primary 68.37.Ef; 68.55.Ac; 68.65.Hb; 81.07.Ta; 81.16.Dn.

  1. Influence of Cast Iron Structure on the Glassmold Equipment Operational Defects

    Directory of Open Access Journals (Sweden)

    I. O. Leushin

    2015-01-01

    Full Text Available The growing demand for glass packaging contributes to the increase in production capacity of glass-container plants. Their equipment (cast iron glass-forming sets operates in continuous mode under complex cyclic thermal loads, which lead to the formation of operational defects on the working surfaces of details: graphite falling, cracks, oxidation, etc. Particular influence on the formation of these defects renders the microstructure of the material at the time of installation of details on the line.The article identifies the causes for formation of operational defects, formulates the ways to remedy them and prevent their occurrence.The authors studied details made from grey cast iron with flake and spherical forms of graphite. It is found that in the process of exploitation of the material is greatly reducing its hardness, strength, resistance to oxidation through of graphitization processes, chemical interaction of glass and iron, shock loads working edges. It is proved that the choice of initial microstructure of cast iron (the metal base, the graphite form, the presence of structural-free cementite exercises a determining influence on the durability of the mold tooling. The article proposes differential (layered arrangement of the graphite phase of cast iron in the alloy matrix (ferrite. This arrangement of high-carbon phase can simultaneously increase the thermal and oxidation resistance of the material. The formation of a layered structure of iron is produced by the intensification of the processes of alloying, modifying and directional freezing the melt.These data can be used to select the material of details by manufacturers glass-molds tooling.

  2. Structural peculiarities and point defects of bulk-ZnO single crystals

    International Nuclear Information System (INIS)

    Kaurova, I.A.; Kuz’micheva, G.M.; Rybakov, V.B.; Cousson, A.; Gayvoronsky, V.Ya.

    2014-01-01

    Highlights: • ZnO single crystals of different color were grown by the hydrothermal method. • Point defects in ZnO have been firstly investigated by neutron diffraction. • Presence of additional reflections caused by kinetic growth effects was revealed. • The relationship between the color and zinc and oxygen vacancies was found. • Photoinduced variation of transmittance versus the CW laser intensity was analyzed. - Abstract: ZnO single crystals are related to promising direct wide band gap semiconductor materials belonging to the A II B VI type of compounds with wurtzite structure. “Unintentional” n-type conductivity in ZnO may be caused by zinc and oxygen vacancies, and interstitial zinc atoms. To date, the comprehensive structural investigation and analysis of point defects in ZnO is absent in literature. Green, light green and almost colorless ZnO single crystals grown by the hydrothermal method in concentrated alkali solutions 4M(KOH) + 1M(LiOH) + 0.1M(NH 4 OH) on monohedral seeds [0 0 0 1] at crystallization temperatures in the range of 330–350 °C and pressures in the range of 30–50 MPa have been firstly investigated by neutron diffraction. It was revealed the presence of additional reflections (∼12–∼16%) for all the crystals caused by kinetic growth effects that give grounds to assign them to the space group P3 rather than to P6 3 mc. Analysis of the refined compositions together with the color of ZnO crystals does not rule out the relationship between the color and vacancies in the zinc and oxygen positions whose concentration decreases with the discoloration of the samples. The analysis of the photoinduced variation of the total and on-axis transmittance versus the CW laser intensity showed that the colored samples have profound deep defects related to oxygen vacancies

  3. Defect and structural imperfection effects on the electronic properties of BiTeI surfaces

    International Nuclear Information System (INIS)

    Fiedler, Sebastian; Seibel, Christoph; Lutz, Peter; Bentmann, Hendrik; Reinert, Friedrich; El-Kareh, Lydia; Bode, Matthias; Eremeev, Sergey V; Tereshchenko, Oleg E; Kokh, Konstantin A; Chulkov, Evgueni V; Kuznetsova, Tatyana V; Grebennikov, Vladimir I

    2014-01-01

    The surface electronic structure of the narrow-gap seminconductor BiTeI exhibits a large Rashba-splitting which strongly depends on the surface termination. Here we report on a detailed investigation of the surface morphology and electronic properties of cleaved BiTeI single crystals by scanning tunneling microscopy, photoelectron spectroscopy (ARPES, XPS), electron diffraction (SPA-LEED) and density functional theory calculations. Our measurements confirm a previously reported coexistence of Te- and I-terminated surface areas originating from bulk stacking faults and find a characteristic length scale of ∼100 nm for these areas. We show that the two terminations exhibit distinct types of atomic defects in the surface and subsurface layers. For electronic states resided on the I terminations we observe an energy shift depending on the time after cleavage. This aging effect is successfully mimicked by depositon of Cs adatoms found to accumulate on top of the I terminations. As shown theoretically on a microscopic scale, this preferential adsorbing behaviour results from considerably different energetics and surface diffusion lengths at the two terminations. Our investigations provide insight into the importance of structural imperfections as well as intrinsic and extrinsic defects on the electronic properties of BiTeI surfaces and their temporal stability. (paper)

  4. Local structure and defects in ion irradiated KTaO3

    Science.gov (United States)

    Zhang, F. X.; Xi, J.; Zhang, Y.; Tong, Yang; Xue, H.; Huang, R.; Trautmann, C.; Weber, W. J.

    2018-04-01

    The modification of the local structure in cubic perovskite KTaO3 irradiated with 3 MeV and 1.1 GeV Au ions is studied by Raman and x-ray absorption spectroscopy, complemented by density functional theory (DFT) calculations. In the case of irradiation with 3 MeV Au ions where displacement cascade processes are dominant, the Ta L3-edge x-ray absorption measurements suggest that a peak corresponding to the Ta-O bonds in the TaO6 octahedra splits, which is attributed to the formation of TaK antisite defects that are coupled with oxygen vacancies, V O. This finding is consistent with the DFT calculations. Under irradiation with 1.1 GeV ions, the intense ionization and electronic energy deposition lead to a blue shift and an intensity reduction of active Raman bands. In the case of sequential irradiations, extended x-ray absorption fine structure measurements reveal a decrease in concentration of coupled TaK-V O defects under subsequent irradiation with 1.1 GeV Au ions.

  5. Extended deep level defects in Ge-condensed SiGe-on-Insulator structures fabricated using proton and helium implantations

    International Nuclear Information System (INIS)

    Kwak, D.W.; Lee, D.W.; Oh, J.S.; Lee, Y.H.; Cho, H.Y.

    2012-01-01

    SiGe-on-Insulator (SGOI) structures were created using the Ge condensation method, where an oxidation process is performed on the SiGe/Si structure. This method involves rapid thermal chemical vapor deposition and H + /He + ion-implantations. Deep level defects in these structures were investigated using deep level transient spectroscopy (DLTS) by varying the pulse injection time. According to the DLTS measurements, a deep level defect induced during the Ge condensation process was found at 0.28 eV above the valence band with a capture cross section of 2.67 × 10 −17 cm 2 , two extended deep levels were also found at 0.54 eV and 0.42 eV above the valence band with capture cross sections of 3.17 × 10 −14 cm 2 and 0.96 × 10 −15 cm 2 , respectively. In the SGOI samples with ion-implantation, the densities of the newly generated defects as well as the existing defects were decreased effectively. Furthermore, the Coulomb barrier heights of the extended deep level defects were drastically reduced. Thus, we suggest that the Ge condensation method with H + ion implantation could reduce deep level defects generated from the condensation and control the electrical properties of the condensed SiGe layers. - Highlights: ► We have fabricated low-defective SiGe-on-Insulator (SGOI) with implantation method. ► H + and He + -ions are used for ion-implantation method. ► We have investigated the deep level defects of SGOI layers. ► Ge condensation method using H + ion implantation could reduce extended defects. ► They could enhance electrical properties.

  6. X-ray diffuse scattering effects from Coulomb-type defects in multilayered structures

    International Nuclear Information System (INIS)

    Olikhovskii, S.I.; Molodkin, V.B.; Skakunova, E.S.; Kislovskii, E.N.; Fodchuk, I.M.

    2009-01-01

    The theoretical X-ray diffraction model starting from Takagi-Taupin equation has been developed for the description of coherent and diffuse components of the rocking curve (RC) measured from the multilayered crystal structure with randomly distributed Coulomb-type defects in all the layers and substrate. The model describes both diffuse scattering (DS) intensity distribution and influence of DS on attenuation and angular redistribution of the coherent X-ray scattering intensity. By analyzing the total measured RC with using the proposed diffraction model, the chemical compositions, strains, and characteristics of dislocation loops in layers and substrate of the multilayered structure with InGaAsN/GaAs single quantum well have been determined. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  7. Magnetite Fe3O4 (111) Surfaces: Impact of Defects on Structure, Stability, and Electronic Properties

    KAUST Repository

    Noh, Jung Hyun

    2015-08-04

    We present a comprehensive investigation, via first-principles density functional theory (DFT) calculations, of various surface terminations of magnetite, Fe3O4 (111), a major iron oxide which has also a number of applications in electronics and spintronics. We compare the thermodynamic stability and electronic structure among the different surfaces terminations. Interestingly, we find that surfaces modified with point defects and adatoms can be more stable than bulk-like terminations. These surfaces show different surface chemistry, electronic structures and distinctive spin polarization features near the Fermi level from those previously considered in the literature. Our studies provide an atomic level insight for magnetite surfaces, which is a necessary step to understanding their interfaces with organic layers in OLED and spintronic devices.

  8. Multiband Bandstop Filter using an I-Stub-Loaded Meandered Defected Microstrip Structure

    Directory of Open Access Journals (Sweden)

    G. R. Koirala

    2016-04-01

    Full Text Available This paper presents a compact multiband bandstop filter (BSF that utilizes an I-stub embedded within a meandered defected microstrip structure (MDMS. The proposed design for obtaining a single stopband is analyzed by using a transmission line network model. On the basis of the single stopband structure, we designed and fabricated a dual- and tri-band bandstop filters operating at 2.5/6.78 GHz and 1.98/5.60/7.78 GHz, respectively, thereby exploring the concept of generating as many stopbands by simply adding the same number of I-stubs. The proposed filter also features the possibility of tuning the resonant frequencies by varying the width of the I-stubs.

  9. Harmonic Suppressed Slot Antennas Using Rectangular/Circular Defected Ground Structures

    Directory of Open Access Journals (Sweden)

    Mohammad Saeid Ghaffarian

    2012-01-01

    Full Text Available Two wide rectangle-shaped microstrip-fed 2.6-GHz slot antennas using defected ground structures (DGSs with a low design complexity are proposed to achieve wideband harmonic suppression. To accomplish this, two rectangular DGSs (RDGSs in the first antenna and two circular DGSs (CDGSs in the second one with various dimensions are etched into the ground plane, which could have a wideband-stop characteristic. Simulated and measured reflection coefficients indicate that the two proposed structures effectively suppress the second and third harmonics up to 23 dB between 3.5 and 10.5 GHz with a maximum ripple of 2.4 dB. In addition, the radiation patterns and peak gains of the antennas can be suppressed at least 17 dB and 7.1 dBi, respectively, at the third harmonic frequency of 7.86 GHz.

  10. Magnetite Fe3O4 (111) Surfaces: Impact of Defects on Structure, Stability, and Electronic Properties

    KAUST Repository

    Noh, Jung Hyun; Osman, Osman I; Aziz, Saadullah G.; Winget, Paul; Bredas, Jean-Luc

    2015-01-01

    We present a comprehensive investigation, via first-principles density functional theory (DFT) calculations, of various surface terminations of magnetite, Fe3O4 (111), a major iron oxide which has also a number of applications in electronics and spintronics. We compare the thermodynamic stability and electronic structure among the different surfaces terminations. Interestingly, we find that surfaces modified with point defects and adatoms can be more stable than bulk-like terminations. These surfaces show different surface chemistry, electronic structures and distinctive spin polarization features near the Fermi level from those previously considered in the literature. Our studies provide an atomic level insight for magnetite surfaces, which is a necessary step to understanding their interfaces with organic layers in OLED and spintronic devices.

  11. Vectors of Defects in Reinforced Concrete Structures in Onshore Oil and Gas Process Plants

    Directory of Open Access Journals (Sweden)

    Dabo Baba Hammad

    2018-01-01

    Full Text Available There is a global outcry over the speedy deterioration of structures in oil and gas facilities. While marine environment is considered the leading factor in the deterioration of offshore structures, there is no single factor considered as the main cause of the problem in onshore structures. Therefore, the aim of this paper is to present the result of global survey on the major factors causing the deterioration of concrete structures in onshore oil and gas facilities. To realize the objectives of the paper, an e-questionnaire was administered through two International LinkedIn groups with a membership mainly dominated by experts in onshore oil and gas facilities. 159 respondents completed the questionnaires, and the reliability of the responses was calculated to be 0.950 which is considered excellent. Relative importance index was used in ranking the factors, and it was observed that environmental factors ranked as the dominant factors causing the deterioration of concrete structures in onshore process plants. Another important finding in the study is the role that experience plays on the perception of experts on the causes of defects on concrete structures.

  12. Resolving Point Defects in the Hydration Structure of Calcite (10.4) with Three-Dimensional Atomic Force Microscopy

    Science.gov (United States)

    Söngen, Hagen; Reischl, Bernhard; Miyata, Kazuki; Bechstein, Ralf; Raiteri, Paolo; Rohl, Andrew L.; Gale, Julian D.; Fukuma, Takeshi; Kühnle, Angelika

    2018-03-01

    It seems natural to assume that defects at mineral surfaces critically influence interfacial processes such as the dissolution and growth of minerals in water. The experimental verification of this claim, however, is challenging and requires real-space methods with utmost spatial resolution, such as atomic force microscopy (AFM). While defects at mineral-water interfaces have been resolved in 2D AFM images before, the perturbation of the surrounding hydration structure has not yet been analyzed experimentally. In this Letter, we demonstrate that point defects on the most stable and naturally abundant calcite (10.4) surface can be resolved using high-resolution 3D AFM—even within the fifth hydration layer. Our analysis of the hydration structure surrounding the point defect shows a perturbation of the hydration with a lateral extent of approximately one unit cell. These experimental results are corroborated by molecular dynamics simulations.

  13. Amplitude of Light Scattering by a Truncated Pyramid and Cone in the Rayleigh-Gans-Debye Approximation

    Directory of Open Access Journals (Sweden)

    Konstantin A. Shapovalov

    2013-01-01

    Full Text Available The article considers general approach to structured particle and particle system form factor calculation in the Rayleigh-Gans-Debye (RGD approximation. Using this approach, amplitude of light scattering by a truncated pyramid and cone formulas in RGD approximation are obtained. Light scattering indicator by a truncated pyramid and cone in the RGD approximation are calculated.

  14. Amplified emission and modified spectral features in an opal hetero-structure mediated by passive defect mode localization

    Science.gov (United States)

    Rout, Dipak; Kumar, Govind; Vijaya, R.

    2018-01-01

    A photonic crystal hetero-structure consisting of a passive planar defect of SiO2 thin film sandwiched between two identical opals grown by inward growing self-assembly method using Rhodamine-B dye-doped polystyrene microspheres is studied for the characteristics of dye emission. The optical properties and the defect mode characteristics of the hetero-structure are studied from the reflection and transmission measurements. Laser-induced fluorescence from the hetero-structure showed amplified and spectrally narrowed emission compared to the photonic crystal emphasizing the role of the defect mode and distributed feedback. The enhanced emission is also complemented by the reduction in fluorescence decay time in the case of the hetero-structure in comparison to the 3D photonic crystals.

  15. Structural and defects induced phenomena in γ-rays irradiated 6H-SiC

    International Nuclear Information System (INIS)

    Sibuyi, P.; Ngom, B.D.; Kotsedi, L.

    2016-01-01

    Damages and/or defects induced by γ-rays irradiation on 6H-SiC single crystals in channeled configuration towards 〈006〉/〈0012〉 crystallographic directions are reported in the range of 0–1200 kGy. Atomic force microscopy, X-rays diffraction, Raman and photoluminescence investigations were used to obtain a comprehensive set of informations on the nature and population distribution of the induced defects. Primarily, there was no carbon clusterization upon γ-rays irradiation and hence no formation of others SiC polytypes. In contrast, the γ-rays irradiation has induced an increase of the surface roughness at higher doses, which indicates a structural degradation. Larger doses induced an emergence of deeper shallow traps at energies greater than 350 meV below the bandgap. - Highlights: • No formation of others SiC polytypes. • The gamma rays irradiation has induced a slight surface amorphization. • A re-crystallization at lower and higher doses is noticed. • Larger doses induced a substantial internal stress.

  16. Reliability implications of defects in high temperature annealed Si/SiO2/Si structures

    International Nuclear Information System (INIS)

    Warren, W.L.; Fleetwood, D.M.; Shaneyfelt, M.R.; Winokur, P.S.; Devine, R.A.B.; Mathiot, D.; Wilson, I.H.; Xu, J.B.

    1994-01-01

    High-temperature post-oxidation annealing of poly-Si/SiO 2 /Si structures such as metal-oxide-semiconductor capacitors and metal-oxide-semiconductor field effect transistors is known to result in enhanced radiation sensitivity, increased 1/f noise, and low field breakdown. The authors have studied the origins of these effects from a spectroscopic standpoint using electron paramagnetic resonance (EPR) and atomic force microscopy. One result of high temperature annealing is the generation of three types of paramagnetic defect centers, two of which are associated with the oxide close to the Si/SiO 2 interface (oxygen-vacancy centers) and the third with the bulk Si substrate (oxygen-related donors). In all three cases, the origin of the defects may be attributed to out-diffusion of O from the SiO 2 network into the Si substrate with associated reduction of the oxide. The authors present a straightforward model for the interfacial region which assumes the driving force for O out-diffusion is the chemical potential difference of the O in the two phases (SiO 2 and the Si substrate). Experimental evidence is provided to show that enhanced hole trapping and interface-trap and border-trap generation in irradiated high-temperature annealed Si/SiO 2 /Si systems are all related either directly, or indirectly, to the presence of oxygen vacancies

  17. The force pyramid: a spatial analysis of force application during virtual reality brain tumor resection.

    Science.gov (United States)

    Azarnoush, Hamed; Siar, Samaneh; Sawaya, Robin; Zhrani, Gmaan Al; Winkler-Schwartz, Alexander; Alotaibi, Fahad Eid; Bugdadi, Abdulgadir; Bajunaid, Khalid; Marwa, Ibrahim; Sabbagh, Abdulrahman Jafar; Del Maestro, Rolando F

    2017-07-01

    OBJECTIVE Virtual reality simulators allow development of novel methods to analyze neurosurgical performance. The concept of a force pyramid is introduced as a Tier 3 metric with the ability to provide visual and spatial analysis of 3D force application by any instrument used during simulated tumor resection. This study was designed to answer 3 questions: 1) Do study groups have distinct force pyramids? 2) Do handedness and ergonomics influence force pyramid structure? 3) Are force pyramids dependent on the visual and haptic characteristics of simulated tumors? METHODS Using a virtual reality simulator, NeuroVR (formerly NeuroTouch), ultrasonic aspirator force application was continually assessed during resection of simulated brain tumors by neurosurgeons, residents, and medical students. The participants performed simulated resections of 18 simulated brain tumors with different visual and haptic characteristics. The raw data, namely, coordinates of the instrument tip as well as contact force values, were collected by the simulator. To provide a visual and qualitative spatial analysis of forces, the authors created a graph, called a force pyramid, representing force sum along the z-coordinate for different xy coordinates of the tool tip. RESULTS Sixteen neurosurgeons, 15 residents, and 84 medical students participated in the study. Neurosurgeon, resident and medical student groups displayed easily distinguishable 3D "force pyramid fingerprints." Neurosurgeons had the lowest force pyramids, indicating application of the lowest forces, followed by resident and medical student groups. Handedness, ergonomics, and visual and haptic tumor characteristics resulted in distinct well-defined 3D force pyramid patterns. CONCLUSIONS Force pyramid fingerprints provide 3D spatial assessment displays of instrument force application during simulated tumor resection. Neurosurgeon force utilization and ergonomic data form a basis for understanding and modulating resident force

  18. A pliocene cliff-line around the Giza Pyramids Plateau, Egypt

    OpenAIRE

    Aigner, Thomas

    1982-01-01

    Aigner, T., 1983. A Pliocene cliff-line around the Giza Pyramids Plateau, Egypt. Palaeogeogr., Palaeoclimatol., Palaeoecol., 4 2 : 313—322. Escarpments bordering the Giza Pyramids Plateau represent the cliff-line of a Pliocene transgression up the pre-Nile ("Eonile") Valley. Geomorphologically, a limestone cliff can be distinguished from a slip-block shore associated with a distinct fining-up sequence. Differences in bedrock lithology and in structure (Joint pattern, faults) are morphogen...

  19. Ab-initio study of magnetism behavior in TiO{sub 2} semiconductor with structural defects

    Energy Technology Data Exchange (ETDEWEB)

    Zarhri, Z., E-mail: z.zarhri@gmail.com; Houmad, M.; Ziat, Y.; El Rhazouani, O.; Slassi, A.; Benyoussef, A.; El Kenz, A.

    2016-05-15

    Magnetic, electronic and structural properties of titanium dioxide material with different structural defects are studied using the first-principles ab-initio calculations and the Korringa–Kohn–Rostoker method (KKR) combined with the coherent potential approximation (CPA) method in connection with the local density approximation (LDA). We investigated all structural defects in rutile TiO{sub 2} such as Titanium interstitial (Ti{sub i}), Titanium anti-sites (Ti{sub o}), Titanium vacancies (V{sub Ti}), Oxygen interstitial (O{sub i}), Oxygen anti-sites (O{sub Ti}) and oxygen vacancies (V{sub o}). Mechanisms of hybridization and interaction between magnetic atoms are investigated. The transition temperature is computed using the Mean Field Approximation (MFA).Magnetic stability energy of ferromagnetic and disordered local moment states is calculated to determine the most stable state. Titanium anti-sites have a half-metallic aspect. We also studied the change type caused by structural defects in this material. - Highlights: • Green function technique is used to study disordered systems. • We used DFT to study electronic structure of TiO{sub 2} perturbed by defects. • TiO{sub 2} with titanium antisite defect posesses a magnetic behavior. • The transition temperature is computed using the Mean Field Approximation.

  20. Active and passive infrared thermography applied to the detection and characterization of hidden defects in structure

    Science.gov (United States)

    Dumoulin, Jean

    2013-04-01

    Infrared thermography for Non Destructive Testing (NDT) has encountered a wide spreading this last 2 decades, in particular thanks to emergence on the market of low cost uncooled infrared camera. So, infrared thermography is not anymore a measurement technique limited to laboratory application. It has been more and more involved in civil engineering and cultural heritage applications, but also in many other domains, as indicated by numerous papers in the literature. Nevertheless, laboratory, measurements are done as much as possible in quite ideal conditions (good atmosphere conditions, known properties of materials, etc.), while measurement on real site requires to consider the influence of not controlled environmental parameters and additional unknown thermal properties. So, dedicated protocol and additional sensors are required for measurement data correction. Furthermore, thermal excitation is required to enhance the signature of defects in materials. Post-processing of data requires to take into account the protocol used for the thermal excitation and sometimes its nature to avoid false detection. This analysis step is based on signal and image processing tool and allows to carry out the detection. Characterization of anomalies detected at the previous step can be done by additional signal processing in particular for manufactured objects. The use of thermal modelling and inverse method allows to determine properties of the defective area. The present paper will first address a review of some protocols currently in use for field measurement with passive and/or active infrared measurements. Illustrations in various experiments carried out on civil engineering structure will be shown and discussed. In a second part, different post-processing approaches will be presented and discussed. In particular, a review of the most standard processing methods like Fast Fourier Analysis, Principal Components Analysis, Polynomial Decomposition, defect characterization using

  1. Evaluation of the Green Egyptian Pyramid

    Directory of Open Access Journals (Sweden)

    Mohamed Gamal Ammar

    2012-12-01

    The research concluded to the need of developing the Egyptian pyramid system through studying more global systems, in addition to the need to benefit from the Egyptian experience stock of solutions and environmental treatments in ancient architecture.

  2. Numerical tools for the study of defect dynamics in quasiperiodic structures

    International Nuclear Information System (INIS)

    Barak, G.; Lifshitz, R.

    2004-01-01

    Full Text:We have developed a set of numerical tools for the quantitative study of defect dynamics in quasiperiodic structures, with the intention of addressing in the near future some of the open questions regarding the dynamics of dislocations in quasicrystals. IS'e intend to apply these tools to study dislocation motion in the dynamical equation of Lifshitz and Petrich [1] whose steady-state solutions are quasiperiodic, exhibiting dodecagonal (12-fold) rotational symmetry. Here we demonstrate our ability to inject an arbitrary set of dislocations-parametrized by the homotopy group of the D-torus (here D=4)-and quantitatively follow the positions of these dislocations as the equation evolves in time. We measure dislocation velocities as a function of applied stress and shear, as well as the phonon and phason strains that accompany this motion as the system evolves in time

  3. Elimination of trench defects and V-pits from InGaN/GaN structures

    International Nuclear Information System (INIS)

    Smalc-Koziorowska, Julita; Grzanka, Ewa; Czernecki, Robert; Schiavon, Dario; Leszczyński, Mike

    2015-01-01

    The microstructural evolution of InGaN/GaN multiple quantum wells grown by metalorganic chemical vapor phase epitaxy was studied as a function of the growth temperature of the GaN quantum barriers (QBs). We observed the formation of basal stacking faults (BSFs) in GaN QBs grown at low temperature. The presence of BSFs terminated by stacking mismatch boundaries (SMBs) leads to the opening of the structure at the surface into a V-shaped trench loop. This trench may form above an SMB, thereby terminating the BSF, or above a junction between the SMB and a subsequent BSF. Fewer BSFs and thus fewer trench defects were observed in GaN QBs grown at temperatures higher than 830 °C. Further increase in the growth temperature of the GaN QBs led to the suppression of the threading dislocation opening into V-pits

  4. Compact and Wide Stopband Lowpass Filter Using Open Complementary Split Ring Resonator and Defected Ground Structure

    Directory of Open Access Journals (Sweden)

    S. S. Karthikeyan

    2015-09-01

    Full Text Available A compact (0.16 λg x 0.08 λg and wide stop¬band lowpass filter design using open complementary split ring resonator (OCSRR and defected ground structure (DGS is presented in this paper. Low pass filter is con-structed using two cascaded stages of OCSRR. Since the rejection bandwidth of the OCSRR is narrow, tapered dumbbell shaped DGS section is placed under the OCSRR to enhance the bandwidth. The cutoff frequency (fc of the proposed lowpass filter is 1.09 GHz. The rejection band¬width of the filter covers the entire ultra wideband spec¬trum. Hence the spurious passband suppression is achieved up to 10 fc. The designed filter has been fabri¬cated and validated by experimental results

  5. The influence of melt purification and structure defects on mid-infrared light emitting diodes

    CERN Document Server

    Krier, A

    2003-01-01

    Mid-infrared light emitting diodes which exhibit more than 7 mW (pulsed) and 0.35 mW dc output power at 3.3 mu m and at room temperature have been fabricated by liquid phase epitaxy using Pb as a neutral solvent. Using Pb solution an increase in pulsed output power of between two and three times was obtained compared with InAs light emitting diodes (LEDs) made using rare-earth gettering. The performance improvements were attributed to a reduction in residual carrier concentration arising from the removal of un-intentional donors and structure defects in the InAs active region material. These LEDs are well matched to the CH sub 4 absorption spectrum and potentially could form the basis of a practical infrared CH sub 4 gas sensor.

  6. A Compact Narrow-Band Bandstop Filter Using Spiral-Shaped Defected Microstrip Structure

    Directory of Open Access Journals (Sweden)

    J. Wang

    2014-04-01

    Full Text Available A novel compact narrow-band bandstop filter is implemented by using the proposed spiral-shaped defected microstrip structure (SDMS in this paper. Compared with other DMSs, the presented SDMS exhibits the advantage of compact size and narrow stopband. Meanwhile, an approximate design rule of the SDMS is achieved and the effects of the dimensions on the resonant frequency and 3 dB fractional bandwidth (FBW are analyzed in detail. Both the simulation and measurement results of the fabricated bandstop filter show that it has a 10 dB stopband from 3.4 GHz to 3.6 GHz with more than 45 dB rejection at the center frequency.

  7. Electronic structure and STM images simulation of defects on hBN/ black-phosphorene heterostructures: A theoretical study

    Science.gov (United States)

    Ospina, D. A.; Cisternas, E.; Duque, C. A.; Correa, J. D.

    2018-03-01

    By first principles calculations which include van der Waals interactions, we studied the electronic structure of hexagonal boron-nitride/black-phosphorene heterostructures (hBN/BP). In particular the role of several kind of defects on the electronic properties of black-phosphorene monolayer and hBN/BP heterostructure was analyzed. The defects under consideration were single and double vacancies, as well Stone-Wale type defects, all of them present in the phosphorene layer. In this way, we found that the electronic structure of the hBN/BP is modified according the type of defect that is introduced. As a remarkable feature, our results show occupied states at the Fermi Level introduced by a single vacancy in the energy gap of the hBN/BP heterostructure. Additionally, we performed simulations of scanning tunneling microscopy images. These simulations show that is possible to discriminate the kind of defect even when the black-phosphorene monolayer is part of the heterostructure hBN/BP. Our results may help to discriminate among several kind of defects during experimental characterization of these novel materials.

  8. Evaluation of the Green Egyptian Pyramid

    OpenAIRE

    Ammar, Mohamed Gamal

    2012-01-01

    In January 2009 was established the Egyptian Council for evaluating green building, then the Board issue a primary version of the Egyptian pyramid in 2010, and as a result of economic, social and political changes that happened in Egypt after the Arab spring period, the study of regional experiences of neighboring countries in Africa and Asia in the development of evaluation system for green buildings of global systems that can contribute to the development of the Egyptian pyramid to promote ...

  9. Discovery of a big void in Khufu's Pyramid by observation of cosmic-ray muons.

    Science.gov (United States)

    Morishima, Kunihiro; Kuno, Mitsuaki; Nishio, Akira; Kitagawa, Nobuko; Manabe, Yuta; Moto, Masaki; Takasaki, Fumihiko; Fujii, Hirofumi; Satoh, Kotaro; Kodama, Hideyo; Hayashi, Kohei; Odaka, Shigeru; Procureur, Sébastien; Attié, David; Bouteille, Simon; Calvet, Denis; Filosa, Christopher; Magnier, Patrick; Mandjavidze, Irakli; Riallot, Marc; Marini, Benoit; Gable, Pierre; Date, Yoshikatsu; Sugiura, Makiko; Elshayeb, Yasser; Elnady, Tamer; Ezzy, Mustapha; Guerriero, Emmanuel; Steiger, Vincent; Serikoff, Nicolas; Mouret, Jean-Baptiste; Charlès, Bernard; Helal, Hany; Tayoubi, Mehdi

    2017-12-21

    The Great Pyramid, or Khufu's Pyramid, was built on the Giza plateau in Egypt during the fourth dynasty by the pharaoh Khufu (Cheops), who reigned from 2509 bc to 2483 bc. Despite being one of the oldest and largest monuments on Earth, there is no consensus about how it was built. To understand its internal structure better, we imaged the pyramid using muons, which are by-products of cosmic rays that are only partially absorbed by stone. The resulting cosmic-ray muon radiography allows us to visualize the known and any unknown voids in the pyramid in a non-invasive way. Here we report the discovery of a large void (with a cross-section similar to that of the Grand Gallery and a minimum length of 30 metres) situated above the Grand Gallery. This constitutes the first major inner structure found in the Great Pyramid since the nineteenth century. The void, named ScanPyramids' Big Void, was first observed with nuclear emulsion films installed in the Queen's chamber, then confirmed with scintillator hodoscopes set up in the same chamber and finally re-confirmed with gas detectors outside the pyramid. This large void has therefore been detected with high confidence by three different muon detection technologies and three independent analyses. These results constitute a breakthrough for the understanding of the internal structure of Khufu's Pyramid. Although there is currently no information about the intended purpose of this void, these findings show how modern particle physics can shed new light on the world's archaeological heritage.

  10. Analysis of Side-Wall Structure of Grown-in Twin-Type Octahedral Defects in Czochralski Silicon

    Science.gov (United States)

    Ueki, Takemi; Itsumi, Manabu; Takeda, Tadao

    1998-04-01

    We analyzed the side-wall structure of grown-in octahedral defects in Czochralski silicon standard wafers for large-scale integrated circuits. There are two types of twin octahedral defects: an overlapping type and an adjacent type. In the twin octahedral defects of the overlapping type, a hole is formed in the connection part. The side-wall layer in the hole part is formed continually and is the same thickness as the side-wall layers of both octahedrons. In the twin octahedral defects of the adjacent type, a partition layer is formed in the connection part. Our electron energy-loss spectroscopy analyses identified that the side-wall layer includes SiO2.

  11. Influence of Deposition Pressure on the Properties of Round Pyramid Textured a-Si:H Solar Cells for Maglev.

    Science.gov (United States)

    Lee, Jaehyeong; Choi, Wonseok; Lee, Kyuil; Lee, Daedong; Kang, Hyunil

    2016-05-01

    HIT (Heterojunction with Intrinsic Thin-layer) photovoltaic cells is one of the highest efficiencies in the commercial solar cells. The pyramid texturization for reducing surface reflectance of HIT solar cells silicon wafers is widely used. For the low leakage current and high shunt of solar cells, the intrinsic amorphous silicon (a-Si:H) on substrate must be uniformly thick of pyramid structure. However, it is difficult to control the thickness in the traditional pyramid texturing process. Thus, we textured the intrinsic a-Si:H thin films with the round pyramidal structure by using HNO3, HF, and CH3COOH solution. The characteristics of round pyramid a-Si:H solar cells deposited at pressure of 500, 1000, 1500, and 2000 mTorr by PECVD (Plasma Enhanced Chemical Vapor Deposition) was investigated. The lifetime, open circuit voltage, fill factor and efficiency of a-Si:H solar cells were investigated with respect to various deposition pressure.

  12. Response of Soft Continuous Structures and Topological Defects to a Temperature Gradient.

    Science.gov (United States)

    Kurita, Rei; Mitsui, Shun; Tanaka, Hajime

    2017-09-08

    Thermophoresis, which is mass transport induced by a temperature gradient, has recently attracted considerable attention as a new way to transport materials. So far the study has been focused on the transport of discrete structures such as colloidal particles, proteins, and polymers in solutions. However, the response of soft continuous structures such as membranes and gels to a temperature gradient has been largely unexplored. Here we study the behavior of a lamellar phase made of stacked surfactant bilayer membranes under a temperature gradient. We find the migration of membranes towards a low-temperature region, causing the increase in the degree of membrane undulation fluctuations towards that direction. This is contrary to our intuition that the fluctuations are weaker at a lower temperature. We show that this can be explained by temperature-gradient-induced migration of membranes under the topological constraint coming from the connectivity of each membrane. We also reveal that the pattern of an edge dislocation array formed in a wedge-shaped cell can be controlled by a temperature gradient. These findings suggest that application of a temperature gradient provides a novel way to control the organization of soft continuous structures such as membranes, gels, and foams, in a manner essentially different from the other types of fields, and to manipulate topological defects.

  13. Defect structure of yttria-stabilized zirconia and its influence on the ionic conductivity at elevated temperatures

    DEFF Research Database (Denmark)

    Goff, J.P.; Hayes, W.; Hull, S.

    1999-01-01

    The defect structure of cubic fluorite structured yttria-stabilized zirconia (ZrO2)(1-x)(Y2O3)(x) has been investigated over the composition range 0.100(3)less than or equal to x less than or equal to 0.241 (10) and temperatures T(K) up to 2780(10) K, using single-crystal specimens. Analysis of n......, we propose that the anomalous decrease in the ionic conductivity with increasing x is a consequence of the decreasing mobility of the isolated defects, possibly due to blockage by the increasing number of static aggregates....

  14. Influence of crystal orientation on the formation of femtosecond laser-induced periodic surface structures and lattice defects accumulation

    Energy Technology Data Exchange (ETDEWEB)

    Sedao, Xxx; Garrelie, Florence, E-mail: florence.garrelie@univ-st-etienne.fr; Colombier, Jean-Philippe; Reynaud, Stéphanie; Pigeon, Florent [Université de Lyon, CNRS, UMR5516, Laboratoire Hubert Curien, Université de Saint Etienne, Jean Monnet, F-42023 Saint-Etienne (France); Maurice, Claire; Quey, Romain [Ecole Nationale Supérieure des Mines de Saint-Etienne, CNRS, UMR5307, Laboratoire Georges Friedel, F-42023 Saint-Etienne (France)

    2014-04-28

    The influence of crystal orientation on the formation of femtosecond laser-induced periodic surface structures (LIPSS) has been investigated on a polycrystalline nickel sample. Electron Backscatter Diffraction characterization has been exploited to provide structural information within the laser spot on irradiated samples to determine the dependence of LIPSS formation and lattice defects (stacking faults, twins, dislocations) upon the crystal orientation. Significant differences are observed at low-to-medium number of laser pulses, outstandingly for (111)-oriented surface which favors lattice defects formation rather than LIPSS formation.

  15. Quantifying hidden defect in multi-layered structures by using eddy current system combined with a scanner

    International Nuclear Information System (INIS)

    Huang Pingjie; Zhou Zekui; Wu Zhaotong

    2005-01-01

    The eddy current testing forward model of scanning inspection of multi-layered structures is introduced and simulation work is carried out to reveal the interaction between the scanning coil and defects with different geometric properties. A multi-frequency ECT experimental instrument combined with a scanner is established and scanning inspections are performed to detect the artificial etched flaws with different geometric parameters in the multi-layered structures. The predicted signals by the forward model are compared with the measured signals and the defects are characterized

  16. Thermodynamic properties of nonstoichiometric H-Nb2 Osub(5-x) derived from a statistical model of its defect structure

    International Nuclear Information System (INIS)

    Schilling, O.F.

    1986-01-01

    A statistical method for the treatment of the defect structure of oxides is applied to H-Nb 2 Osub(5-x) and its thermodynamic properties are derived as a function of x and temperature. The results based on a model of Nb O 3 vacancy clusters located at the tetrahedral columns of the structure presented very good agreement with experimental data in the literature [2]. Further, the predicted arrangement of the clusters of vacancies along the columns at the limiting composition of the H-Nb 2 O 5 phase indicates, according to recent electron microscopy experiments [18, 19], that the initial step of the transformation is the collapse of the structure around rows of defective sites along the columns, involving Andersson and Wadsley's [20] cooperative migration of atoms. The limiting compositions of the H-Nb 2 O 5 and Nb 53 O 132 phases are also correctly predicted on the basis of electrostatic interactions among defect units only. Thus elastic interactions among planar defects appear to affect only the arrangement of such defects, and not the compositions of the initial and final compounds. (author)

  17. Demonstration for the Applicability of the EPRI ETSS on the SG Tube Wear Defects Formed at the Tube Support Structure

    International Nuclear Information System (INIS)

    Shin, Ki Seok; Cheon, Keun Young; Nam, Min Woo; Min, Kyong Mahn

    2013-01-01

    In this paper, the authorized EPRI ETSS 27906.2 applied to the detection of tapered wear volumetric indications and depth sizing within the free span area, loose part not present was reviewed and applied to the site SG tubes for getting the actual value of the wear depth and providing structural integrity interpretation based on engineering evaluation. The experiment to demonstrate the applicability of EPRI ETSS was performed by the employment of the newly prepared STD tube and resulted in ensuring the effectiveness and equivalency of the EPRI ETSS as well. The authorized EPRI ETSS 27906.2 for getting the actual value of the wear depth and providing structural integrity interpretation based on engineering evaluation was reviewed and applied to the site SG tubes. The testing results were reviewed with the influences of SG tube material and the support structure. The impact of the tube materials was insignificant and that of the tube support structure showed somewhat conservative results. The testing resulted in successful demonstration of applicability of the EPRI ETSS on the SG tube wear defects at the tube support. One of the major flaw mechanisms detected in the currently operating domestic OPR-1000 pressurized water reactors(PWR's) steam generator(SG) tubes is wear defect. In general, wear defect has been constantly detected in the upper tube bundle imposed to the flow induced vibration interaction between tube and its support structure, and the quantity of the affected tubes has also shown the tendency to increase as plant operation life is added. In order to take appropriate measures and maintain the structural integrity for the SG tubes, wear defect is currently categorized as active damage mechanism and the tubes containing 40% or greater wear depth of the nominal tube wall thickness shall be plugged per SGMP(SG Management Program) Recently, a fairly large amplitude of wear defects on the Batwing(BW), one of the upper tube support structures in the SG tubes

  18. Demonstration for the Applicability of the EPRI ETSS on the SG Tube Wear Defects Formed at the Tube Support Structure

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Ki Seok; Cheon, Keun Young; Nam, Min Woo [Korea Hydro and Nuclear Power Co. Ltd, Daejeon (Korea, Republic of); Min, Kyong Mahn [Universal Monitoring and Inspection Inc., Daejeon (Korea, Republic of)

    2013-10-15

    In this paper, the authorized EPRI ETSS 27906.2 applied to the detection of tapered wear volumetric indications and depth sizing within the free span area, loose part not present was reviewed and applied to the site SG tubes for getting the actual value of the wear depth and providing structural integrity interpretation based on engineering evaluation. The experiment to demonstrate the applicability of EPRI ETSS was performed by the employment of the newly prepared STD tube and resulted in ensuring the effectiveness and equivalency of the EPRI ETSS as well. The authorized EPRI ETSS 27906.2 for getting the actual value of the wear depth and providing structural integrity interpretation based on engineering evaluation was reviewed and applied to the site SG tubes. The testing results were reviewed with the influences of SG tube material and the support structure. The impact of the tube materials was insignificant and that of the tube support structure showed somewhat conservative results. The testing resulted in successful demonstration of applicability of the EPRI ETSS on the SG tube wear defects at the tube support. One of the major flaw mechanisms detected in the currently operating domestic OPR-1000 pressurized water reactors(PWR's) steam generator(SG) tubes is wear defect. In general, wear defect has been constantly detected in the upper tube bundle imposed to the flow induced vibration interaction between tube and its support structure, and the quantity of the affected tubes has also shown the tendency to increase as plant operation life is added. In order to take appropriate measures and maintain the structural integrity for the SG tubes, wear defect is currently categorized as active damage mechanism and the tubes containing 40% or greater wear depth of the nominal tube wall thickness shall be plugged per SGMP(SG Management Program) Recently, a fairly large amplitude of wear defects on the Batwing(BW), one of the upper tube support structures in the SG

  19. Irradiation defect structures in YBa2Cu3O7-x and their correlation with superconducting properties

    International Nuclear Information System (INIS)

    Kirk, M.A.

    1990-11-01

    We review our work on irradiation effects in single crystal YBa 2 CU 3 O 7-x . Transmission electron microscopy has been employed to study the defect microstructures produced by irradiations with fast neutrons, MeV ions (Kr, Ne and p), and electrons. The atomic structure within defect cascades was investigated using 50 keV Kr and Xe ion irradiations to low doses. Evidence is shown for an amorphous structure with some incoherent recrystallization within individual cascades. Correlation with enhancements in critical current density produced by neutron irradiations suggest that this cascade structure effectively pins magnetic flux lines. At sufficiently high fluences of fast neutrons or MeV Kr and Ne ions, a cellular microstructure is found. This structure consists of cells or microcrystallites of good cystalline and superconducting material (in the case of neutron irradiation), with cell walls of amorphous material. Full amorphization proceeds with the growth of cell wall volume. The formation of this microstructure coincides with a decrease in critical transport current, but is not observed by magnetization measurements. Increases in critical current density under proton irradiation, comparable to those produced by neutron irradiation, have been reported. The defect structure produced by proton irradiations is examined here and found to differ from that of neutron irradiations. Our most recent measurements of changes in critical temperature and current density, and defect microstructure following electron irradiations will be described. 20 refs., 6 figs

  20. Atomic-scale structure and properties of highly stable antiphase boundary defects in Fe3O4.

    Science.gov (United States)

    McKenna, Keith P; Hofer, Florian; Gilks, Daniel; Lazarov, Vlado K; Chen, Chunlin; Wang, Zhongchang; Ikuhara, Yuichi

    2014-12-10

    The complex and intriguing properties of the ferrimagnetic half metal magnetite (Fe 3 O 4 ) are of continuing fundamental interest as well as being important for practical applications in spintronics, magnetism, catalysis and medicine. There is considerable speculation concerning the role of the ubiquitous antiphase boundary (APB) defects in magnetite, however, direct information on their structure and properties has remained challenging to obtain. Here we combine predictive first principles modelling with high-resolution transmission electron microscopy to unambiguously determine the three-dimensional structure of APBs in magnetite. We demonstrate that APB defects on the {110} planes are unusually stable and induce antiferromagnetic coupling between adjacent domains providing an explanation for the magnetoresistance and reduced spin polarization often observed. We also demonstrate how the high stability of the {110} APB defects is connected to the existence of a metastable bulk phase of Fe 3 O 4 , which could be stabilized by strain in films or nanostructures.

  1. Asymmetric Macular Structural Damage Is Associated With Relative Afferent Pupillary Defects in Patients With Glaucoma

    Science.gov (United States)

    Gracitelli, Carolina P. B.; Tatham, Andrew J.; Zangwill, Linda M.; Weinreb, Robert N.; Abe, Ricardo Y.; Diniz-Filho, Alberto; Paranhos, Augusto; Baig, Saif; Medeiros, Felipe A.

    2016-01-01

    Purpose We examined the relationship between relative afferent pupillary defects (RAPDs) and macular structural damage measured by macular thickness and macular ganglion cell-inner plexiform layer (mGCIPL) thickness in patients with glaucoma. Methods A cross-sectional study was done of 106 glaucoma patients and 85 healthy individuals from the Diagnostic Innovations in Glaucoma Study. All subjects underwent standard automated perimetry (SAP) and optic nerve and macular imaging using Cirrus Spectral Domain Optical Coherence Tomography (SDOCT). Glaucoma was defined as repeatable abnormal SAP or progressive glaucomatous changes on stereo photographs. Pupil responses were assessed using an automated pupillometer, which records the magnitude of RAPD (RAPD score), with additional RAPD scores recorded for each of a series of colored stimuli (blue, red, green, and yellow). The relationship between RAPD score and intereye differences (right minus left eye) in circumpapillary retinal nerve fiber layer (cpRNFL) thickness, mGCIPL, macular thickness, and SAP mean deviation (MD), was examined using linear regression. Results There was fair correlation between RAPD score and asymmetric macular structural damage measured by intereye difference in mGCIPL thickness (R2 = 0.285, P glaucoma. PMID:27064394

  2. Formation, structure and magnetism of the metastable defect fluorite phases AVO3.5+x (A=In, Sc)

    International Nuclear Information System (INIS)

    Shafi, Shahid P.; Lundgren, Rylan J.; Cranswick, Lachlan M.D.; Bieringer, Mario

    2007-01-01

    We report the preparation and stability of ScVO 3.5+x and the novel phase InVO 3.5+x . AVO 3.5+x (A=Sc, In) defect fluorite structures are formed as metastable intermediates during the topotactic oxidation of AVO 3 bixbyites. The oxidation pathway has been studied in detail by means of thermogravimetric/differential thermal analysis and in-situ powder X-ray diffraction. The oxidation of the bixbyite phase follows a topotactic pathway at temperatures between 300 and 400 deg. C in air/carbon dioxide. The range of accessible oxygen stoichiometries for the AVO 3.5+x structures following this pathway are 0.00≤x≤0.22. Rietveld refinements against powder X-ray and neutron data revealed that InVO 3.54 and ScVO 3.70 crystallize in the defect fluorite structure in space group Fm-3 m (227) with a=4.9863(5) and 4.9697(3)A, respectively with A 3+ /V 4+ disorder on the (4a) cation site. Powder neutron diffraction experiments indicate clustering of oxide defects in all samples. Bulk magnetic measurements showed the presence of V 4+ and the absence of magnetic ordering at low temperatures. Powder neutron diffraction experiments confirmed the absence of a long range ordered magnetic ground state. - Graphical abstract: Topotactic oxidation of AVO 3 bixbyite to AVO 3.5 defect fluorite structure followed by in-situ powder X-ray diffraction. The upper structural diagram shows a six coordinated (A/V)-O 6 fragment in bixbyite, the lower structure illustrates the same seven-fold coordinated (A/V)-O 7 cubic environment in the defect fluorite structure

  3. Lattice vibrations and thermal properties of carbon nitride with defect ZnS structure from first-principles calculations

    NARCIS (Netherlands)

    Fang, C.M.; Wijs, G.A. de

    2004-01-01

    The phonon spectrum Of C3N4 with defect zincblende-type structure (deltaC(3)N(4)) was calculated by density functional theory (DFT) techniques. The results permit an assessment of important mechanical and thermodynamical properties such as the bulk modulus, lattice specific heat, vibration energy,

  4. Structural defects and epitaxial rotation of C-60 and C-70(111) films on GeS(001)

    DEFF Research Database (Denmark)

    Bernaerts, D.; Van Tendeloo, G.; Amelinckx, S.

    1996-01-01

    A transmission electron microscopy study of epitaxial C60 and C70 films grown on a GeS (001) surface is presented. The relationship between the orientation of the substrate and the films and structural defects in the films, such as grain boundaries, unknown in bulk C60 and C70 crystals, are studied...

  5. Structural Defects in Polyallylcarbosilane Dendrimers and Their PolyolDerivatives Characterized by NMR and MALDI-TOF Mass Spectrometry

    Czech Academy of Sciences Publication Activity Database

    Krupková, Alena; Čermák, Jan; Walterová, Zuzana; Horský, Jiří

    2010-01-01

    Roč. 43, č. 10 (2010), s. 4511-4519 ISSN 0024-9297 R&D Projects: GA MŠk(CZ) LC06070 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z40500505 Keywords : carbosilane dendrimer s * maldi-tof ms * structural defects Subject RIV: CC - Organic Chemistry Impact factor: 4.838, year: 2010

  6. TCM Analysis of Defected Ground Structures for MIMO Antenna Designs in Mobile Terminals

    KAUST Repository

    Ghalib, Asim

    2017-08-14

    In this paper, the theory of characteristic modes (TCM) is used for the first time to analyze the behavior of defected ground structures (DGS) when added to antenna designs. A properly designed DGS introduces currents opposite in direction to the original characteristic modes (CM) currents thus reducing mutual coupling. TCM is also applied to multiple-inputmultiple- output (MIMO) antenna systems to develop a systematic approach that can predict whether the isolation can be enhanced further or not. For this purpose two 4-element and one 2-element MIMO designs, i.e. monopole and planar inverted-F antennas (PIFA) are studied. The addition of different antenna elements affects the CM significantly as well as differently. Some of the CM excited on the antenna surface contribute to the coupling between the antenna ports that is why they can be classified as coupling modes. To improve the isolation, the DGS should be introduced at certain locations that blocks the coupling modes but at the same time does not affect the non-coupling modes. If their is no such location or the current on the surface of the chassis for coupling and non-coupling modes is approximately same, the isolation cannot be enhanced further. Using this approach, isolation was improved on an average by 11 dB in all the designs considered, giving the most isolation enhancement following a systematic way compared to other works.

  7. Defect analysis in GaN films of HEMT structure by cross-sectional cathodoluminescence

    Science.gov (United States)

    Isobe, Yasuhiro; Hung, Hung; Oasa, Kohei; Ono, Tasuku; Onizawa, Takashi; Yoshioka, Akira; Takada, Yoshiharu; Saito, Yasunobu; Sugiyama, Naoharu; Tsuda, Kunio; Sugiyama, Toru; Mizushima, Ichiro

    2017-06-01

    Defect analysis of GaN films in high electron mobility transistor (HEMT) structures by cross-sectional cathodoluminescence (X-CL) is demonstrated as a useful technique for improving the current collapse of GaN-HEMT devices, and the relationship between crystal quality and device characteristics is also investigated. The crystal quality of intrinsic-GaN (i-GaN) and carbon-doped GaN produced clearly different peak intensities of blue luminescence (BL), yellow luminescence (YL), and band-edge emission (BE), which is independently detected by X-CL. Current collapse in GaN-HEMT devices is found to be determined by the BL/BE and YL/BE ratios at the top of the i-GaN layer, which is close to the channel. Moreover, the i-GaN thickness required in order to minimize the BL/BE and YL/BE ratios and the thickness dependency of GaN for minimizing the BL/BE and YL/BE ratios depending on the growth conditions can be evaluated by X-CL. However, there is no correlation between current collapse in GaN-HEMT devices and the YL/BE ratio by conventional photoluminescence because HEMT devices consist of multiple GaN layers and the YL signal is detected from the carbon-doped GaN layer. Thus, the X-CL analysis method is a useful technique for device design in order to suppress current collapse.

  8. Detection of Defect-Induced Magnetism in Low-Dimensional ZnO Structures by Magnetophotocurrent.

    Science.gov (United States)

    Lorite, Israel; Kumar, Yogesh; Esquinazi, Pablo; Zandalazini, Carlos; de Heluani, Silvia Perez

    2015-09-09

    The detection of defect-induced magnetic order in single low-dimensional oxide structures is in general difficult because of the relatively small yield of magnetically ordered regions. In this work, the effect of an external magnetic field on the transient photocurrent measured after light irradiation on different ZnO samples at room temperature is studied. It has been found that a magnetic field produces a change in the relaxation rate of the transient photocurrent only in magnetically ordered ZnO samples. This rate can decrease or increase with field, depending on whether the magnetically ordered region is in the bulk or only at the surface of the ZnO sample. The phenomenon reported here is of importance for the development of magneto-optical low-dimensional oxides devices and provides a new guideline for the detection of magnetic order in low-dimensional magnetic semiconductors. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. In-situ volumetric topography of IC chips for defect detection using infrared confocal measurement with active structured light

    International Nuclear Information System (INIS)

    Chen, Liang-Chia; Le, Manh-Trung; Phuc, Dao Cong; Lin, Shyh-Tsong

    2014-01-01

    The article presents the development of in-situ integrated circuit (IC) chip defect detection techniques for automated clipping detection by proposing infrared imaging and full-field volumetric topography. IC chip inspection, especially held during or post IC packaging, has become an extremely critical procedure in IC fabrication to assure manufacturing quality and reduce production costs. To address this, in the article, microscopic infrared imaging using an electromagnetic light spectrum that ranges from 0.9 to 1.7 µm is developed to perform volumetric inspection of IC chips, in order to identify important defects such as silicon clipping, cracking or peeling. The main difficulty of infrared (IR) volumetric imaging lies in its poor image contrast, which makes it incapable of achieving reliable inspection, as infrared imaging is sensitive to temperature difference but insensitive to geometric variance of materials, resulting in difficulty detecting and quantifying defects precisely. To overcome this, 3D volumetric topography based on 3D infrared confocal measurement with active structured light, as well as light refractive matching principles, is developed to detect defects the size, shape and position of defects in ICs. The experimental results show that the algorithm is effective and suitable for in-situ defect detection of IC semiconductor packaging. The quality of defect detection, such as measurement repeatability and accuracy, is addressed. Confirmed by the experimental results, the depth measurement resolution can reach up to 0.3 µm, and the depth measurement uncertainty with one standard deviation was verified to be less than 1.0% of the full-scale depth-measuring range. (paper)

  10. Binding energetics of substitutional and interstitial helium and di-helium defects with grain boundary structure in α-Fe

    Energy Technology Data Exchange (ETDEWEB)

    Tschopp, M. A., E-mail: mark.tschopp@gatech.edu [Dynamic Research Corporation, (on site at) U.S. Army Research Laboratory, Aberdeen Proving Ground, Maryland 21005 (United States); Center for Advanced Vehicular Systems, Mississippi State University, Starkville, Mississippi 39762 (United States); Gao, F.; Yang, L. [Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Solanki, K. N. [Arizona State University, School for Engineering of Matter, Transport and Energy, Tempe, Arizona 85287 (United States)

    2014-01-21

    The formation/binding energetics and length scales associated with the interaction between He atoms and grain boundaries in BCC α-Fe were explored. Ten different low Σ grain boundaries from the 〈100〉 and 〈110〉 symmetric tilt grain boundary systems were used. In this work, we then calculated formation/binding energies for 1–2 He atoms in the substitutional and interstitial sites (HeV, He{sub 2}V, HeInt, He{sub 2}Int) at all potential grain boundary sites within 15 Å of the boundary (52 826 simulations total). The present results provide detailed information about the interaction energies and length scales of 1–2 He atoms with grain boundaries for the structures examined. A number of interesting new findings emerge from the present study. For instance, the Σ3(112) twin boundary in BCC Fe possesses a much smaller binding energy than other boundaries, which corresponds in long time dynamics simulations to the ability of an interstitial He defect to break away from the boundary in simulations on the order of nanoseconds. Additionally, positive correlations between the calculated formation/binding energies of the He defects (R > 0.9) asserts that the local environment surrounding each site strongly influences the He defect energies and that highly accurate quantum mechanics calculations of lower order defects may be an adequate predictor of higher order defects. Various metrics to quantify or classify the local environment were compared with the He defect binding energies. The present work shows that the binding and formation energies for He defects are important for understanding the physics of He diffusion and trapping by grain boundaries, which can be important for modeling He interactions in polycrystalline steels.

  11. Binding energetics of substitutional and interstitial helium and di-helium defects with grain boundary structure in α-Fe

    International Nuclear Information System (INIS)

    Tschopp, M. A.; Gao, F.; Yang, L.; Solanki, K. N.

    2014-01-01

    The formation/binding energetics and length scales associated with the interaction between He atoms and grain boundaries in BCC α-Fe were explored. Ten different low Σ grain boundaries from the 〈100〉 and 〈110〉 symmetric tilt grain boundary systems were used. In this work, we then calculated formation/binding energies for 1–2 He atoms in the substitutional and interstitial sites (HeV, He 2 V, HeInt, He 2 Int) at all potential grain boundary sites within 15 Å of the boundary (52 826 simulations total). The present results provide detailed information about the interaction energies and length scales of 1–2 He atoms with grain boundaries for the structures examined. A number of interesting new findings emerge from the present study. For instance, the Σ3(112) twin boundary in BCC Fe possesses a much smaller binding energy than other boundaries, which corresponds in long time dynamics simulations to the ability of an interstitial He defect to break away from the boundary in simulations on the order of nanoseconds. Additionally, positive correlations between the calculated formation/binding energies of the He defects (R > 0.9) asserts that the local environment surrounding each site strongly influences the He defect energies and that highly accurate quantum mechanics calculations of lower order defects may be an adequate predictor of higher order defects. Various metrics to quantify or classify the local environment were compared with the He defect binding energies. The present work shows that the binding and formation energies for He defects are important for understanding the physics of He diffusion and trapping by grain boundaries, which can be important for modeling He interactions in polycrystalline steels

  12. Defect structures in YBa/sub 2/Cu/sub 3/O/sub 7-x/ produced by electron irradiation

    International Nuclear Information System (INIS)

    Kirk, M.A.; Baker, M.C.; Liu, J.Z.; Lam, D.J.; Weber, H.W.

    1988-01-01

    Defect structures in YBa/sub 2/Cu/sub 3/O/sub 7-x/ produced by electron irradiation at 300 K were investigated by transmission electron microscopy. Threshold energies for the production of visible defects were determined to be 152 keV and 131 keV (+- 7 keV) in directions near the a and b (b>a) axes (both perpendicular to c, the long axis in the orthorhombic structure), respectively. During above threshold irradiations in an electron flux of 3x10/sup 18/ cm/sup -2/ s/sup -1/, extended defects were observed to form and grow to sizes of 10-50 nm over 1000 s in material thickness 20-200 nm. Such low electron threshold energies suggest oxygen atom displacements with recoil energies near 20 eV. The observation of movement of twin boundaries during irradiation just above threshold suggests movement of the basal plane oxygen atoms by direct displacement or defect migration processes. Crystals irradiated above threshold were observed after about 24 hours to have transformed to a structure heavily faulted on planes perpendicular to the c axis

  13. Do neural tube defects lead to structural alterations in the human bladder?

    Science.gov (United States)

    Pazos, Helena M F; Lobo, Márcio Luiz de P; Costa, Waldemar S; Sampaio, Francisco J B; Cardoso, Luis Eduardo M; Favorito, Luciano Alves

    2011-05-01

    Anencephaly is the most severe neural tube defect in human fetuses. The objective of this paper is to analyze the structure of the bladder in anencephalic human fetuses. We studied 40 bladders of normal human fetuses (20 male and 20 female, aged 14 to 23 WPC) and 12 bladders of anencephalic fetuses (5 male and 7 female, aged 18 to 22 WPC). The bladders were removed and processed by routine histological techniques. Stereological analysis of collagen, elastic system fibers and smooth muscle was performed in sections. Data were expressed as volumetric density (Vv-%). The images were captured with Olympus BX51 microscopy and Olympus DP70 camera. The stereological analysis was done using the software Image Pro and Image J. For biochemical analysis, samples were fixed in acetone, and collagen concentrations were expressed as micrograms of hydroxyproline per mg of dry tissue. Means were statistically compared using the unpaired t-test (p<0.05). We observed a significant increase (p<0.0001) in the Vv of collagen in the bladders of anencephalic fetuses (69.71%) when compared to normal fetuses (52.74%), and a significant decrease (p<0.0001) in the Vv of smooth muscle cells in the bladders of anencephalic fetuses (23.96%) when compared to normal fetuses (38.35%). The biochemical analyses showed a higher concentration of total collagen in the bladders of anencephalic fetuses (37354 µg/mg) when compared to normal fetuses (48117 µg/mg, p<0.02). The structural alterations of the bladder found in this study may suggest the existence of functional alterations in the bladder of anencephalic human fetuses.

  14. Steady distribution structure of point defects near crystal-melt interface under pulling stop of CZ Si crystal

    Science.gov (United States)

    Abe, T.; Takahashi, T.; Shirai, K.

    2017-02-01

    In order to reveal a steady distribution structure of point defects of no growing Si on the solid-liquid interface, the crystals were grown at a high pulling rate, which Vs becomes predominant, and the pulling was suddenly stopped. After restoring the variations of the crystal by the pulling-stop, the crystals were then left in prolonged contact with the melt. Finally, the crystals were detached and rapidly cooled to freeze point defects and then a distribution of the point defects of the as-grown crystals was observed. As a result, a dislocation loop (DL) region, which is formed by the aggregation of interstitials (Is), was formed over the solid-liquid interface and was surrounded with a Vs-and-Is-free recombination region (Rc-region), although the entire crystals had been Vs rich in the beginning. It was also revealed that the crystal on the solid-liquid interface after the prolonged contact with the melt can partially have a Rc-region to be directly in contact with the melt, unlike a defect distribution of a solid-liquid interface that has been growing. This experimental result contradicts a hypothesis of Voronkov's diffusion model, which always assumes the equilibrium concentrations of Vs and Is as the boundary condition for distribution of point defects on the growth interface. The results were disscussed from a qualitative point of view of temperature distribution and thermal stress by the pulling-stop.

  15. Structure and strain relaxation effects of defects in InxGa1−xN epilayers

    International Nuclear Information System (INIS)

    Rhode, S. L.; Fu, W. Y.; Massabuau, F. C.-P.; Kappers, M. J.; McAleese, C.; Oehler, F.; Humphreys, C. J.; Sahonta, S.-L.; Moram, M. A.; Dusane, R. O.

    2014-01-01

    The formation of trench defects is observed in 160 nm-thick In x Ga 1−x N epilayers with x ≤ 0.20, grown on GaN on (0001) sapphire substrates using metalorganic vapour phase epitaxy. The trench defect density increases with increasing indium content, and high resolution transmission electron microscopy shows an identical structure to those observed previously in InGaN quantum wells, comprising meandering stacking mismatch boundaries connected to an I 1 -type basal plane stacking fault. These defects do not appear to relieve in-plane compressive strain. Other horizontal sub-interface defects are also observed within the GaN pseudosubstrate layer of these samples and are found to be pre-existing threading dislocations which form half-loops by bending into the basal plane, and not basal plane stacking faults, as previously reported by other groups. The origins of these defects are discussed and are likely to originate from a combination of the small in-plane misorientation of the sapphire substrate and the thermal mismatch strain between the GaN and InGaN layers grown at different temperatures.

  16. Characterizing the nano-structure and defect structure of nano-scaled non-ferrous structural alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ghamarian, Iman, E-mail: imanghamarian@yahoo.com [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States); Samimi, Peyman; Liu, Yue [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States); Center for Advanced Non-Ferrous Structural Alloys, an NSF-I/UCRC between the University of North Texas (Denton, TX, 76203) and the Colorado School of Mines (Golden, CO, 80401) (United States); Poorganji, Behrang; Vasudevan, Vijay K. [Department of Mechanical and Materials Engineering, University of Cincinnati, Cincinnati, OH 45221 (United States); Collins, Peter C. [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States); Center for Advanced Non-Ferrous Structural Alloys, an NSF-I/UCRC between the University of North Texas (Denton, TX, 76203) and the Colorado School of Mines (Golden, CO, 80401) (United States)

    2016-03-15

    The presence and interaction of nanotwins, geometrically necessary dislocations, and grain boundaries play a key role in the mechanical properties of nanostructured crystalline materials. Therefore, it is vital to determine the orientation, width and distance of nanotwins, the angle and axis of grain boundary misorientations as well as the type and the distributions of dislocations in an automatic and statistically meaningful fashion in a relatively large area. In this paper, such details are provided using a transmission electron microscope-based orientation microscopy technique called ASTAR™/precession electron diffraction. The remarkable spatial resolution of this technique (~ 2 nm) enables highly detailed characterization of nanotwins, grain boundaries and the configuration of dislocations. This orientation microscopy technique provides the raw data required for the determination of these parameters. The procedures to post-process the ASTAR™/PED datasets in order to obtain the important (and currently largely hidden) details of nanotwins as well as quantifications of dislocation density distributions are described in this study. - Highlights: • EBSD cannot characterize defects such as dislocations, grain boundaries and nanotwins in severely deformed metals. • TEM based orientation microscopy technique called ASTAR™/PED was used to resolve the problem. • Locations and orientations of nanotwins, dislocation density distribution and grain boundary characters can be resolved. • This work provides the bases for further studies on the interactions between dislocations, grain boundaries and nanotwins. • The computation part is explained sufficiently which helps the readers to post process their own data.

  17. Tiling a Pyramidal Polycube with Dominoes

    Directory of Open Access Journals (Sweden)

    Olivier Bodini

    2007-05-01

    Full Text Available The notion of pyramidal polycubes, namely the piling-up of bricks of a non-increasing size, generalizes in ℝ n the concept of trapezoidal polyominoes. In the present paper, we prove that n-dimensional dominoes can tile a pyramidal polycube if and only if the latter is balanced, that is, if the number of white cubes is equal to the number of black ones for a chessboard-like coloration, generalizing the result of [BC92] when n=2

  18. Assessment of structures and stabilities of defect clusters and surface energies predicted by nine interatomic potentials for UO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Taller, Stephen A. [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States); Bai, Xian-Ming, E-mail: xianming.bai@inl.gov [Fuels Modeling and Simulation Department, Idaho National Laboratory, Idaho Falls, ID 83415 (United States)

    2013-11-15

    The irradiation in nuclear reactors creates many point defects and defect clusters in uranium dioxide (UO{sub 2}) and their evolution severely degrades the thermal and mechanical properties of the nuclear fuels. Previously many empirical interatomic potentials have been developed for modeling defect production and evolution in UO{sub 2}. However, the properties of defect clusters and extended defects are usually not fitted into these potentials. In this work nine interatomic potentials for UO{sub 2} are examined by using molecular statics and molecular dynamics to assess their applicability in predicting the properties of various types of defect clusters in UO{sub 2}. The binding energies and structures for these defect clusters have been evaluated for each potential. In addition, the surface energies of voids of different radii and (1 1 0) flat surfaces predicted by these potentials are also evaluated. It is found that both good agreement and significant discrepancies exist for these potentials in predicting these properties. For oxygen interstitial clusters, these potentials predict significantly different defect cluster structures and stabilities; For defect clusters consisting of both uranium and oxygen defects, the prediction is in better agreement; The surface energies predicted by these potentials have significant discrepancies, and some of them are much higher than the experimentally measured values. The results from this work can provide insight on interpreting the outcome of atomistic modeling of defect production using these potentials and may provide guidelines for choosing appropriate potential models to study problems of interest in UO{sub 2}.

  19. On the re-characterisation of defects in structural integrity assessments due to snap-through

    International Nuclear Information System (INIS)

    Burdekin, F.M.; Sherry, A.H.

    2006-01-01

    TAGSI was asked by HSE/NII to comment on the effectiveness of the R6 procedure which permits a surface defect failing an initial assessment to be re-assessed as a through thickness defect of increased length. If the defect passes the re-assessment it may then be considered acceptable. In TAGSI's view re-characterisation needs to be considered separately for contained plastic collapse and ductile or brittle fracture of the remaining ligament. For plastic collapse and ductile tearing of the remaining ligament the R6 rules for re-characterisation appear generally satisfactory. For brittle failure of the ligament in many cases the R6 recommendations will be found satisfactory but for cases of large difference between static and dynamic toughness it is recommended that scoping calculations should be carried out for the defect geometry, loading and material properties of concern

  20. A Backward Pyramid Oriented Optical Flow Field Computing Method for Aerial Image

    Directory of Open Access Journals (Sweden)

    LI Jiatian

    2016-09-01

    Full Text Available Aerial image optical flow field is the foundation for detecting moving objects at low altitude and obtaining change information. In general,the image pyramid structure is embedded in numerical procedure in order to enhance the convergence globally. However,more often than not,the pyramid structure is constructed using a bottom-up approach progressively,ignoring the geometry imaging process.In particular,when the ground objects moving it will lead to miss optical flow or the optical flow too small that could hardly sustain the subsequent modeling and analyzing issues. So a backward pyramid structure is proposed on the foundation of top-level standard image. Firstly,down sampled factors of top-level image are calculated quantitatively through central projection,which making the optical flow in top-level image represent the shifting threshold of the set ground target. Secondly,combining top-level image with its original,the down sampled factors in middle layer are confirmed in a constant proportion way. Finally,the image of middle layer is achieved by Gaussian smoothing and image interpolation,and meanwhile the pyramid is formed. The comparative experiments and analysis illustrate that the backward pyramid can calculate the optic flow field in aerial image accurately,and it has advantages in restraining small ground displacement.

  1. An improved potential drop method for measuring and monitoring defects in structures

    International Nuclear Information System (INIS)

    Oppermann, W.; Keller, H.P.

    1991-01-01

    In its advanced form, the direct-current potential probe measuring technique is a reliable and relatively exact procedure for measuring and monitoring surface defects. In addition, there is the possibility - important for practical purposes - of measuring cracks at the inaccessible side of a component part. The improved accuracy, in particular with regard to short defects, is based on advanced measuring techniques and calibration curves determined at the electrolytical tank. (orig./DG) [de

  2. Detection of structural defects in lecithin membranes by the small-angle neutron scattering method

    International Nuclear Information System (INIS)

    Bezzabotnov, V.Yu.; Gordelij, V.I.; Ostanevich, Yu.M.; Yaguzhinskij, L.S.

    1989-01-01

    Irregularities interpreted as interdomain defects have been detected in model lipid membranes of dipalmitoil lecithin in liquid L α -phase by the method of small-angle scattering (lateral diffraction). The dimensions and concentrations of the defects were about those supposed within the dynamic cluster model of bilayer (Ivkov, 1984). No irregularities were detected in the solid Lβ ' -phase (the diffusion scattering intensity was at least ten times less)

  3. Structural integrity evaluation of SG tube with surface wear-type defects

    International Nuclear Information System (INIS)

    Kim, Jong Min; Huh, Nam Su; Chang, Yoon Suk; Kim, Young Jin; Hwang, Seong Sik; Kim, Joung Soo

    2006-01-01

    During the last two decades, several guidelines have been developed and used for assessing the integrity of a defective Steam Generator (SG) tube that is generally caused by stress corrosion cracking or wall-thinning phenomenon. However, as some of SG tubes are also failed due to fretting and so on, alternative failure estimation schemes are required for relevant defects. In this paper, parametric three-dimensional Finite Element (FE) analyses are carried out under internal pressure condition to simulate the failure behavior of SG tubes with different defect configurations; elliptical wear, tapered and flat wear type defects. Maximum pressures based on material strengths are obtained from more than a hundred FE results to predict the failure of SG tube. After investigating the effect of key parameters such as defect depth, defect length and wrap angle, simplified failure estimation equations are proposed in relation to the equivalent stress at the deepest point in wear region. Comparison of failure pressures predicted by the proposed estimation scheme with corresponding burst test data showed a good agreement

  4. Effect of defects, magnetocrystalline anisotropy, and shape anisotropy on magnetic structure of iron thin films by magnetic force microscopy

    Directory of Open Access Journals (Sweden)

    Ke Xu

    2017-05-01

    Full Text Available Microstructures of magnetic materials, including defects and crystallographic orientations, are known to strongly influence magnetic domain structures. Measurement techniques such as magnetic force microscopy (MFM thus allow study of correlations between microstructural and magnetic properties. The present work probes effects of anisotropy and artificial defects on the evolution of domain structure with applied field. Single crystal iron thin films on MgO substrates were milled by Focused Ion Beam (FIB to create different magnetically isolated squares and rectangles in [110] crystallographic orientations, having their easy axis 45° from the sample edge. To investigate domain wall response on encountering non-magnetic defects, a 150 nm diameter hole was created in the center of some samples. By simultaneously varying crystal orientation and shape, both magnetocrystalline anisotropy and shape anisotropy, as well as their interaction, could be studied. Shape anisotropy was found to be important primarily for the longer edge of rectangular samples, which exaggerated the FIB edge effects and provided nucleation sites for spike domains in non-easy axis oriented samples. Center holes acted as pinning sites for domain walls until large applied magnetic fields. The present studies are aimed at deepening the understanding of the propagation of different types of domain walls in the presence of defects and different crystal orientations.

  5. Structural defects in natural plastically deformed diamonds: Evidence from EPR spectroscopy

    Science.gov (United States)

    Mineeva, R. M.; Titkov, S. V.; Speransky, A. V.

    2009-06-01

    Structural defects formed as a result of plastic deformation in natural diamond crystals have been studied by EPR spectroscopy. The spectra of brown, pink-brown, black-brown, pink-purple, and gray plastically deformed diamonds of type Ia from deposits in Yakutia and the Urals were recorded. The results of EPR spectroscopy allowed us to identify various deformation centers in the structure of natural diamonds and to show that nitrogen centers were transformed under epigenetic mechanical loading. Abundant A centers, consisting of two isomorphic nitrogen atoms located in neighboring structural sites, were destroyed as a result of this process to form a series of N1, N4, W7, M2, and M3 nitrogen centers. Such centers are characterized by an anisotropic spatial distribution and a positive charge, related to the mechanism of their formation. In addition, N2 centers (probably, deformation-produced dislocations decorated by nitrogen) were formed in all plastically deformed diamonds and W10 and W35 centers (the models have not been finally ascertained) were formed in some of them. It has been established that diamonds with various types of deformation-induced color contain characteristic associations of these deformation centers. The diversity of associations of deformation centers indicates appreciable variations in conditions of disintegration of deep-seated rocks, transfer of diamonds to the Earth’s surface, and formation of kimberlitic deposits. Depending on the conditions of mechanical loading, the diamond crystals were plastically deformed by either dislocation gliding or mechanical twinning. Characteristic features of plastic deformation by dislocation gliding are the substantial prevalence of the N2 centers over other deformation centers and the occurrence of the high-spin W10 and W35 centers. The attributes of less frequent plastic deformation by mechanical twinning are unusual localization of the M2 centers and, in some cases, the N1 centers in microtwinned

  6. Correlation between intrinsic hardness and defect structures of ion irradiated Fe alloys

    International Nuclear Information System (INIS)

    Shin, C.; Jin, H. H.; Kwon, J.

    2008-01-01

    Evolution of micro structures and mechanical properties during an in-service irradiation is one of the key issues to be addressed in nuclear materials. Ion irradiation is an effective method to study these irradiation effects thanks to an ease in handling post-irradiated specimens. But the characteristics of an ion irradiation pose a certain difficulty in evaluating irradiation effects. For example, ion irradiated region extends only a few hundred nano-meters from the surface of a sample and the depth profile of an irradiation damage level is quite heterogeneous. Thus it requires special care to quantify the changes in properties after an ion irradiation. We measured changes in a hardness by using a nano-indentation combined with a continuous stiffness measurement (CSM technique. Although the SM technique allows for a continuous measurement of hardness along penetration depth of an indenter; it is difficult to obtain an intrinsic hardness of an irradiation hardened region because one is measuring hardness of a hard layer located on a soft matrix. Thus we modeled the nano-indentation test by using a finite element method. We can extract the intrinsic hardness and the yield stress of an irradiation hardened region by using a so-called inverse method. We investigated the irradiation effects on Fe-Cr binary alloy by using the methods mentioned above. TEM analysis revealed that an irradiation forms dislocation loops with Burgers vector of and 1/2 . These loops varied in size and density with the Cr content and dose level. We discuss in detail a correlation between the measured irradiation-induced changes in the surface hardness and an irradiation induced defect. (authors)

  7. Ancient Pyramids Help Students Learn Math Concepts

    Science.gov (United States)

    Smith, Courtney D.; Stump, Amanda M.; Lazaros, Edward J.

    2010-01-01

    This article presents an activity that allows students to use mathematics and critical-thinking skills to emulate processes used by the ancient Egyptians to prepare the site for the Pyramids of Giza. To accomplish this, they use three different methods. First, they create a square using only simple technological tools that were available to the…

  8. Comparing Volumes of Prisms and Pyramids

    Science.gov (United States)

    Vinogradova, Natalya

    2012-01-01

    Students' experience in using formulas for volumes is often limited to substituting numbers into given formulas. An activity presented in this article may help students make connections between the formulas for volumes of prisms and volumes of pyramids. In addition, some interesting facts from number theory arise, demonstrating strong connections…

  9. The TAPS Pyramid: Where, Who and How?

    Science.gov (United States)

    Hopwood-Stephens, Isabel

    2018-01-01

    The TAPS pyramid was developed in late 2014 and has been available as a download on the Primary Science Teaching Trust (PSTT) website since August 2015. But where has it gone since then? Who is using it? And how is it being used in schools to change primary science assessment practice? This article attempts to answer these questions with data from…

  10. On higher order pyramidal finite elements

    Czech Academy of Sciences Publication Activity Database

    Liu, L.; Davies, K.B.; Křížek, Michal; Guan, L.

    2011-01-01

    Roč. 3, č. 2 (2011), s. 131-140 ISSN 2070-0733 R&D Projects: GA AV ČR(CZ) IAA100190803 Institutional research plan: CEZ:AV0Z10190503 Keywords : pyramidal polynomial basis functions * finite element method * composite elements * three-dimensional mortar elements Subject RIV: BA - General Mathematics Impact factor: 0.750, year: 2011

  11. Jonestown in the Shadow of Maslow's Pyramid.

    Science.gov (United States)

    Easley, Edgar M.; Wigglesworth, David C.

    1979-01-01

    Reviews Maslow's hierarchy of needs in the light of the Jonestown tragedy. Maintains that members of the People's Temple felt frustrated in attaining the lower levels in the world of reality, and so moved outside the pyramid in search of the top, self-actualization. In the process, their primary needs were met. Journal availability: see SO 507…

  12. Combining in situ transmission electron microscopy irradiation experiments with cluster dynamics modeling to study nanoscale defect agglomeration in structural metals

    International Nuclear Information System (INIS)

    Xu Donghua; Wirth, Brian D.; Li Meimei; Kirk, Marquis A.

    2012-01-01

    We present a combinatorial approach that integrates state-of-the-art transmission electron microscopy (TEM) in situ irradiation experiments and high-performance computing techniques to study irradiation defect dynamics in metals. Here, we have studied the evolution of visible defect clusters in nanometer-thick molybdenum foils under 1 MeV krypton ion irradiation at 80 °C through both cluster dynamics modeling and in situ TEM experiments. The experimental details are reported elsewhere; we focus here on the details of model construction and comparing the model with the experiments. The model incorporates continuous production of point defects and/or small clusters, and the accompanying interactions, which include clustering, recombination and loss to the surfaces that result from the diffusion of the mobile defects. To account for the strong surface effect in thin TEM foils, the model includes one-dimensional spatial dependence along the foil depth, and explicitly treats the surfaces as black sinks. The rich amount of data (cluster number density and size distribution at a variety of foil thickness, irradiation dose and dose rate) offered by the advanced in situ experiments has allowed close comparisons with computer modeling and permitted significant validation and optimization of the model in terms of both physical model construct (damage production mode, identities of mobile defects) and parameterization (diffusivities of mobile defects). The optimized model exhibits good qualitative and quantitative agreement with the in situ TEM experiments. The combinatorial approach is expected to bring a unique opportunity for the study of radiation damage in structural materials.

  13. Evaluation of defect density by top-view large scale AFM on metamorphic structures grown by MOVPE

    Energy Technology Data Exchange (ETDEWEB)

    Gocalinska, Agnieszka, E-mail: agnieszka.gocalinska@tyndall.ie; Manganaro, Marina; Dimastrodonato, Valeria; Pelucchi, Emanuele

    2015-09-15

    Highlights: • Metamorphic buffer layers of In{sub x}Ga{sub 1−x}As were grown by MOVPE and characterised by AFM and TEM. • It was found that AFM provides sufficient information to estimate threading defect density in metamorphic structures, even when significant roughness is present. • When planar-view TEM is lacking, a combination of cross-sectional TEM and large scale AFM can provide good evaluation of the material quality. • It is fast, cheap and non-destructive – can be very useful in development process of complicated structures, requiring multiple test growths and characterisation. - Abstract: We demonstrate an atomic force microscopy based method for estimation of defect density by identification of threading dislocations on a non-flat surface resulting from metamorphic growth. The discussed technique can be applied as an everyday evaluation tool for the quality of epitaxial structures and allow for cost reduction, as it lessens the amount of the transmission electron microscopy analysis required at the early stages of projects. Metamorphic structures with low surface defectivities (below 10{sup 6}) were developed successfully with the application of the technique, proving its usefulness in process optimisation.

  14. A new class of morphological pyramids for multiresolution image analysis

    NARCIS (Netherlands)

    Roerdink, Jos B.T.M.; Asano, T; Klette, R; Ronse, C

    2003-01-01

    We study nonlinear multiresolution signal decomposition based on morphological pyramids. Motivated by a problem arising in multiresolution volume visualization, we introduce a new class of morphological pyramids. In this class the pyramidal synthesis operator always has the same form, i.e. a

  15. Exciton binding energy in a pyramidal quantum dot

    Indian Academy of Sciences (India)

    A ANITHA

    2018-03-27

    Mar 27, 2018 ... screening function on exciton binding energy in a pyramid-shaped quantum dot of ... tures may generate unique properties and they show .... where Ee is the ground-state energy of the electron in ... Figure 1. The geometry of the pyramidal quantum dot. base and H is the height of the pyramid which is taken.

  16. Teacher Acquisition of Functional Analysis Methods Using Pyramidal Training

    Science.gov (United States)

    Pence, Sacha T.; St. Peter, Claire C.; Giles, Aimee F.

    2014-01-01

    Pyramidal training involves an experienced professional training a subset of individuals who, in turn, train additional individuals. Pyramidal training is effective for training a variety of behavior-analytic skills with direct-care staff, parents, and teachers. As teachers' roles in behavioral assessment increase, pyramidal training may be…

  17. On the astronomical orientation of the IV dynasty Egyptian pyramids and the dating of the second Giza pyramid

    OpenAIRE

    Magli, Giulio

    2003-01-01

    The data on the astronomical orientation of the IV dynasty Egyptian pyramids are re-analyzed and it is shown that such data suggest an inverse chronology between the `first` and the `second` Giza pyramid.

  18. Tailoring defect structure and optical absorption of porous anodic aluminum oxide membranes

    International Nuclear Information System (INIS)

    Yan Hongdan; Lemmens, Peter; Wulferding, Dirk; Shi, Jianmin; Becker, Klaus Dieter; Lin, Chengtian; Lak, Aidin; Schilling, Meinhard

    2012-01-01

    Defects influence the optical and electronic properties of nanostructured materials that may be relevant for applications. In self-organized anodic aluminum oxide (AAO) templates we have investigated the effect of annealing, doping and nanoscale metal deposition. Optical absorption spectroscopy has been used as a sensitive probe for the defect density in AAO templates. The electronic spectra are found to be dominated by bands which originate from oxygen-deficient color centers (F + , F and F 2 ). In annealing studies, the integrated absorption of the bands changes non-monotonically with annealing temperature and annealing time. This demonstrates that the concentration of defects can be optimized to tailor the optical properties of the AAO. Metallic Au wires are deposited in the template to establish a plasmonic template or array. The investigations provide an interesting insight into the interplay of reactivity and diffusivity on nanoscales. - Highlights: ► Preparation of metal wire arrays in oxide templates with tailored plasmonic properties. ► Oxygen defects are characterized using optical absorption and fluorescence. ► Optical absorption spectra are assigned to energy levels of oxygen vacancies (color centers). ► Annealing and electrodeposition of Au wires minimize defects maintaining the morphology.

  19. Effect of structural defects on electronic and magnetic properties of ZrS2 monolayer

    Science.gov (United States)

    Wang, Haiyang; Zhao, Xu; Gao, Yonghui; Wang, Tianxing; Wei, Shuyi

    2018-04-01

    We aimed at ten configurations of vacancy defects and used the first-principles methods based on density functional theory to research electronic and magnetic properties of ZrS2 monolayer. Results show that the system of two-zirconium vacancy (V2zr) and one Zr atom + one S atom vacancy (V1Zr+1S) can induce to total spin magnetic moment of 0.245μB and 0.196μB, respectively. In addition, three and six S atoms vacancy can induce corresponding system to manifest spin magnetic moment of 0.728μB and 3.311μB, respectively. In S atom vacancy defects, vacancy defects can transform the system from semiconductor to metal, several of the Zr atoms and adjacent S atoms display antiferromagnetism coupling in three apart S atom vacancy defects. Vacancy defects can make the intrisic monolayer ZrS2 transform semiconductor into metal. These results are important for the achievement of spin devices based on ZrS2 semiconductor.

  20. Lattice defects in semiconducting Hg/1-x/Cd/x/Te alloys. III - Defect structure of undoped Hg0.6Cd0.4Te

    Science.gov (United States)

    Vydyanath, H. R.; Donovan, J. D.; Nelson, D. A.

    1981-01-01

    Hall effect measurements were carried out on undoped Hg0.6Cd0.4Te crystals quenched to room temperature subsequent to equilibration at temperatures varying from 450 to 720 C under various partial pressures of Hg. The variation of the hole concentration as a function of the partial pressure of Hg indicates that the native acceptor defects are doubly ionized. Native donor defects are found to be negligible in concentration and the p-type to n-type conversion is shown to be due to residual donors and not due to native donor defects. Thermodynamic constant for the incorporation of the doubly ionized native acceptor defect has been established.

  1. Radiation defect production in quartz crystals with various structure perfectness degree; Radiatsionnoe defektoobrazovanie v kristallakh kvartsa s razlichnoj stepen`yu sovershenstva struktury

    Energy Technology Data Exchange (ETDEWEB)

    Khushvakov, O B

    1992-01-01

    Radiation defects production processes in pure and doped quartz crystals with various structure defectness, caused by preliminary irradiation with neutrons, protons, deuterons and {alpha}-particles, during various electron excitation densities were investigated. The distribution of colour centres along the thickness of irradiated quartz crystals was measured. It was supposed that colour centres are produced on account of inelastic energy losses as the result of collective decay of two or more interacting excitons. It was shown that in quartz crystals under the actions of protons with overthreshold energy 18 MeV and electrons with subthreshold energy 100 keV the same structure defects are formed. It was established that radiation defect production process has two stages. The first stage reveals radiation defects produced by preliminary irradiation. The second one reveals additional intrinsic defects formed under the action of gamma-rays and electrons. The probability dependence of defect production on neutron fluence and masses of incident particles was studied. It was supposed that the creation of additional defects in preliminary irradiated crystals is due to non-radiative decay of electron excitations near radiation-induced defects. It was shown that increase of impurity concentration leads to rate growth of accumulation of radiation induced defects. (A.A.D.) 15 refs. 4 figs.

  2. Pyramidal cells in V1 of African rodents are bigger more branched and more spiny than those in primates.

    Directory of Open Access Journals (Sweden)

    Guy eElston

    2014-02-01

    Full Text Available Pyramidal cells are characterised by markedly different sized dendritic trees, branching patterns and spine density across the cortical mantle. Moreover, pyramidal cells have been shown to differ in structure among homologous cortical areas in different species; however, most of these studies have been conducted in primates. Whilst pyramidal cells have been quantified in a few cortical areas in some other species there are, as yet, no uniform comparative data on pyramidal cell structure in a homologous cortical area among species in different Orders. Here we studied layer III pyramidal cells in V1 of three species of rodents, the greater cane rat, highveld gerbil and four-striped mouse, by the same methodology used to sample data from layer III pyramidal cells in primates. The data reveal markedly different trends between rodents and primates: there is an appreciable increase in the size, branching complexity and number of spines in the dendritic trees of pyramidal cells with increasing size of V1 in the brain in rodents, whereas there is relatively little difference in primates. Moreover, pyramidal cells in rodents are larger, more branched and more spinous than those in primates. For example, the dendritic trees of pyramidal cells in V1 of the cane rat are nearly three times larger, and have more than ten times the number of spines in their basal dendritic trees, than those in V1 of the macaque (7900 and 600, respectively, which has a V1 40 times the size that of the cane rat. It remains to be determined to what extent these differences may result from developmental differences or reflect evolutionary and/or processing specializations.

  3. Research on Debonding Defects in Thermal Barrier Coatings Structure by Thermal-Wave Radar Imaging (TWRI)

    Science.gov (United States)

    Wang, Fei; Liu, Junyan; Mohummad, Oliullah; Wang, Yang

    2018-06-01

    In this paper, thermal-wave radar imaging (TWRI) is introduced to detect debonding defects in SiC-coated Ni-based superalloy plates. Linear frequency modulation signal (chirp) is used as the excitation signal which has a large time-bandwidth product. Artificial debonding defects in SiC coating are excited by the laser beam with the light intensity modulated by a chirp signal. Cross-correlation algorithm and chirp lock-in algorithm are introduced to extract the thermal-wave signal characteristic. The comparative experiment between TWRI reflection mode and transmission mode was carried out. Experiments are conducted to investigate the influence of laser power density, chirp period, and excitation frequency. Experimental results illustrate that chirp lock-in phase has a better detection capability than other characteristic parameters. TWRI can effectively detect simulated debonding defects of SiC-coated Ni-based superalloy plates.

  4. Effects of structure and defect on fatigue limit in high strength ductile irons

    International Nuclear Information System (INIS)

    Kim, Jin Hak; Kim, Min Gun

    2000-01-01

    In this paper, the influence of several factors such as hardness, internal defect and non-propagating crack on fatigue limits was investigated with three kinds of ductile iron specimens. From the experimental results the fatigue limits were examined in relation with hardness and tensile strength in case of high strength specimens under austempering treatment; in consequence the marked improvement of fatigue limits were not showed. The maximum defect size was an important factor to predict and to evaluate the fatigue limits of ductile irons. And, the quantitative relationship between the fatigue limits(σ ω ) and the maximum defect size(√area max ) was expressed as σ ω n · √area max =C 2 . Also, it was possible to explain the difference for the fatigue limits in three ductile irons by introduction of the non-propagating crack rates

  5. Simulation of pattern and defect detection in periodic amplitude and phase structures using photorefractive four-wave mixing

    Science.gov (United States)

    Nehmetallah, Georges; Banerjee, Partha; Khoury, Jed

    2015-03-01

    The nonlinearity inherent in four-wave mixing in photorefractive (PR) materials is used for adaptive filtering. Examples include script enhancement on a periodic pattern, scratch and defect cluster enhancement, periodic pattern dislocation enhancement, etc. through intensity filtering image manipulation. Organic PR materials have large space-bandwidth product, which makes them useful in adaptive filtering techniques in quality control systems. For instance, in the case of edge enhancement, phase conjugation via four-wave mixing suppresses the low spatial frequencies of the Fourier spectrum of an aperiodic image and consequently leads to image edge enhancement. In this work, we model, numerically verify, and simulate the performance of a four wave mixing setup used for edge, defect and pattern detection in periodic amplitude and phase structures. The results show that this technique successfully detects the slightest defects clearly even with no enhancement. This technique should facilitate improvements in applications such as image display sharpness utilizing edge enhancement, production line defect inspection of fabrics, textiles, e-beam lithography masks, surface inspection, and materials characterization.

  6. Defect structures in MgB2 wires introduced by hot isostatic pressing

    International Nuclear Information System (INIS)

    Liao, X Z; Serquis, A; Zhu, Y T; Civale, L; Hammon, D L; Peterson, D E; Mueller, F M; Nesterenko, V F; Gu, Y

    2003-01-01

    The microstructures of MgB 2 wires prepared by the powder-in-tube technique and subsequent hot isostatic pressing were investigated using transmission electron microscopy. A large amount of crystalline defects including small-angle twisting, tilting and bending boundaries, in which high densities of dislocations reside, was found forming sub-grains within MgB 2 grains. It is believed that these defects resulted from particle deformation during the hot isostatic pressing process and are effective flux pinning centres that contribute to the high critical current densities of the wires at high temperatures and at high fields

  7. The relativistic titls of Giza pyramids' entrance-passages

    Science.gov (United States)

    Aboulfotouh, H.

    The tilts of Giza pyramids' entrance-passages have never been considered as if they were the result of relativistic mathematical equations, and never been thought to encode the Earth's obliquity parameters. This paper presents an attempt to retrieve the method of establishing the equations that the pyramids' designer used to quantify the entrance-passages' tilts of these architectonic masterpieces. It proves that the pyramids' designer was able to include the geographic, astronomical and time parameters in one relativistic equation, encoding the date of the design of the Giza pyramids in the tilt of the entrance passage of the great pyramid.

  8. Nanoscale characterization of local structures and defects in photonic crystals using synchrotron-based transmission soft X-ray microscopy

    Science.gov (United States)

    Nho, Hyun Woo; Kalegowda, Yogesh; Shin, Hyun-Joon; Yoon, Tae Hyun

    2016-01-01

    For the structural characterization of the polystyrene (PS)-based photonic crystals (PCs), fast and direct imaging capabilities of full field transmission X-ray microscopy (TXM) were demonstrated at soft X-ray energy. PS-based PCs were prepared on an O2-plasma treated Si3N4 window and their local structures and defects were investigated using this label-free TXM technique with an image acquisition speed of ~10 sec/frame and marginal radiation damage. Micro-domains of face-centered cubic (FCC (111)) and hexagonal close-packed (HCP (0001)) structures were dominantly found in PS-based PCs, while point and line defects, FCC (100), and 12-fold symmetry structures were also identified as minor components. Additionally, in situ observation capability for hydrated samples and 3D tomographic reconstruction of TXM images were also demonstrated. This soft X-ray full field TXM technique with faster image acquisition speed, in situ observation, and 3D tomography capability can be complementally used with the other X-ray microscopic techniques (i.e., scanning transmission X-ray microscopy, STXM) as well as conventional characterization methods (e.g., electron microscopic and optical/fluorescence microscopic techniques) for clearer structure identification of self-assembled PCs and better understanding of the relationship between their structures and resultant optical properties. PMID:27087141

  9. Observations of defect structure evolution in proton and Ni ion irradiated Ni-Cr binary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Briggs, Samuel A., E-mail: sabriggs2@wisc.edu [University of Wisconsin-Madison, 1415 Engineering Drive, Madison, WI 53706 (United States); Barr, Christopher M. [Drexel University, 3141 Chestnut Street, Philadelphia, PA 19104 (United States); Pakarinen, Janne [University of Wisconsin-Madison, 1415 Engineering Drive, Madison, WI 53706 (United States); SKC-CEN Belgian Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium); Mamivand, Mahmood [University of Wisconsin-Madison, 1415 Engineering Drive, Madison, WI 53706 (United States); Hattar, Khalid [Sandia National Laboratories, PO Box 5800, Albuquerque, NM 87185 (United States); Morgan, Dane D. [University of Wisconsin-Madison, 1415 Engineering Drive, Madison, WI 53706 (United States); Taheri, Mitra [Drexel University, 3141 Chestnut Street, Philadelphia, PA 19104 (United States); Sridharan, Kumar [University of Wisconsin-Madison, 1415 Engineering Drive, Madison, WI 53706 (United States)

    2016-10-15

    Two binary Ni-Cr model alloys with 5 wt% Cr and 18 wt% Cr were irradiated using 2 MeV protons at 400 and 500 °C and 20 MeV Ni{sup 4+} ions at 500 °C to investigate microstructural evolution as a function of composition, irradiation temperature, and irradiating ion species. Transmission electron microscopy (TEM) was applied to study irradiation-induced void and faulted Frank loops microstructures. Irradiations at 500 °C were shown to generate decreased densities of larger defects, likely due to increased barriers to defect nucleation as compared to 400 °C irradiations. Heavy ion irradiation resulted in a larger density of smaller voids when compared to proton irradiations, indicating in-cascade clustering of point defects. Cluster dynamics simulations were in good agreement with the experimental findings, suggesting that increases in Cr content lead to an increase in interstitial binding energy, leading to higher densities of smaller dislocation loops in the Ni-18Cr alloy as compared to the Ni-5Cr alloy. - Highlights: • Binary Ni-Cr alloys were irradiated with protons or Ni ions at 400 and 500 °C. • Higher irradiation temperatures yield increased size, decreased density of defects. • Hypothesize that varying Cr content affects interstitial binding energy. • Fitting CD models for loop nucleation to data supports this hypothesis.

  10. The Effect of Face Sheet Wrinkle Defects on the Strength of FRP Sandwich Structures

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Christian; Pettersson, Robert

    2007-01-01

    . In the studies reported here, the influence of wrinkle defects on the in-plane compressive strength of quasi-isotropic carbon fiber reinforced plastic (CFRP) laminates used in PVC foam-cored sandwich panels has been investigated by three approaches: testing of sandwich beam specimens in four-point bending...

  11. Structure, Raman spectra and defect chemistry modelling of conductive pyrochlore oxides

    DEFF Research Database (Denmark)

    Poulsen, F.W.; Glerup, M.; Holtappels, P.

    2000-01-01

    -O(x) and V-O on the O site, interstitial oxygens O-i", and delocalised electrons and electron holes. Four mass action law expressions govern such a model. The defect model can rationalise why home-valent doping, i.e. substitution of Zr(4+) by Ce(4+), can lead to an increase in ionic conductivity...

  12. Effect of Fe Doping by Thermal in-Diffusion on the Defect Structure of Lithium Niobate

    Energy Technology Data Exchange (ETDEWEB)

    Mignoni, S; Zaltron, A; Ciampolillo, M V; Bazzan, M; Argiolas, N; Sada, C; Fontana, M D, E-mail: zaltronam@padova.infm.it

    2010-11-15

    In this work we investigate the iron incorporation in thermally diffused Fe doped LN, by combining two experimental techniques, i.e. micro-Raman spectroscopy and proton induced X rays emission. Our results point out that in substituting for Li, Fe ions induces a decrease of Nb{sub Li} antisite defects and rearrangement of the Nb sublattice.

  13. Stability and electronic structure of iron nanoparticle anchored on defective hexagonal boron nitrogen nanosheet: A first-principle study

    International Nuclear Information System (INIS)

    Lin, Sen; Huang, Jing; Ye, Xinxin

    2014-01-01

    Highlights: • Fe 13 nanoparticle strongly interacts with the monovacancy of h-BN nanosheet. • Significant charges are transferred from Fe 13 to the defective h-BN nanosheet. • The upshift of d-band center makes the surface Fe atoms of supported Fe 13 with higher reactivity. - Abstract: By first-principle methods, we investigate the stability and electronic structures of Fe 13 nanoparticles anchored on hexagonal boron nitrogen nanosheets (h-BNNSs) with monovacancy defect sites. It is found that the defect sites such as boron and nitrogen vacancy significantly increase the adsorption energies of Fe 13 , suggesting that the supported Fe 13 nanoparticles should be very stable against sintering at high temperatures. From the calculated density of states, we testify that the strong interaction is attributed to the coupling between the 3d orbitals of Fe atoms with the sp 2 dangling bonds at the defect sites. The Bader charge and differential charge density analyses reveal that there is significant charge redistribution at the interface between Fe 13 and the substrates, leading to positive charges located on most of the Fe atoms. Additionally, our results show that the strong binding of the nanoparticle results in the upshift of d-band center of Fe 13 toward the Fermi level, thus making the surface Fe atoms with higher reactivity. This work gives a detailed understanding the interaction between Fe 13 nanoparticle and defective h-BNNS and will provide helpful instructions in the design and synthesis of supported Fe-based catalysts in heterogeneous catalysis

  14. On correction of model of stabilization of distribution of concentration of radiation defects in a multilayer structure with account experiment data

    Science.gov (United States)

    Pankratov, E. L.

    2018-05-01

    We introduce a model of redistribution of point radiation defects, their interaction between themselves and redistribution of their simplest complexes (divacancies and diinterstitials) in a multilayer structure. The model gives a possibility to describe qualitatively nonmonotonicity of distributions of concentrations of radiation defects on interfaces between layers of the multilayer structure. The nonmonotonicity was recently found experimentally. To take into account the nonmonotonicity we modify recently used in literature model for analysis of distribution of concentration of radiation defects. To analyze the model we used an approach of solution of boundary problems, which could be used without crosslinking of solutions on interfaces between layers of the considered multilayer structures.

  15. Influence of defect structure on magnetic and electronic properties of Hg1-x Crx Se and Hg1-x Cox Se

    International Nuclear Information System (INIS)

    Prozorovskij, V.D.; Reshidova, I.Yu.; Puzynya, A.I.; Paranchich, Yu.S.

    1996-01-01

    The results of experimental investigations of the Shubnikov-de Haas oscillations at superhigh frequencies, electron spin resonance, magnetic susceptibility, relaxation dielectric losses, and galvanomagnetic measurements in the Hg 1-x Cr x Se and Hg 1-x Co x Se single crystal samples are presented. Analysis of the results Hg 1-x Cr x Se and Hg 1-x Co x Se depend on the defect structure of the substance and the type of defects making this structure. The manifestation of critical phenomena in Hg 1-x Cr x Se also depends on the defect structure

  16. Trace Element Compositions and Defect Structures of High-Purity Quartz from the Southern Ural Region, Russia

    Directory of Open Access Journals (Sweden)

    Jens Götze

    2017-10-01

    Full Text Available Quartz samples of different origin from 10 localities in the Southern Ural region, Russia have been investigated to characterize their trace element compositions and defect structures. The analytical combination of cathodoluminescence (CL microscopy and spectroscopy, electron paramagnetic resonance (EPR spectroscopy, and trace-element analysis by inductively coupled plasma mass spectrometry (ICP-MS revealed that almost all investigated quartz samples showed very low concentrations of trace elements (cumulative concentrations of <50 ppm with <30 ppm Al and <10 ppm Ti and low abundances of paramagnetic defects, defining them economically as “high-purity” quartz (HPQ suitable for high-tech applications. EPR and CL data confirmed the low abundances of substitutional Ti and Fe, and showed Al to be the only significant trace element structurally bound in the investigated quartz samples. CL microscopy revealed a heterogeneous distribution of luminescence centres (i.e., luminescence active trace elements such as Al as well as features of deformation and recrystallization. It is suggested that healing of defects due to deformation-related recrystallization and reorganization processes of the quartz lattice during retrograde metamorphism resulted in low concentrations of CL activator and other trace elements or vacancies, and thus are the main driving processes for the formation of HPQ deposits in the investigated area.

  17. Structural integrity evaluation of X52 gas pipes subjected to external corrosion defects using the SINTAP procedure

    International Nuclear Information System (INIS)

    Adib-Ramezani, H.; Jeong, J.; Pluvinage, G.

    2006-01-01

    In the present study, the SINTAP procedure has been proposed as a general structural integrity tool for semi-spherical, semi-elliptical and long blunt notch defects. The notch stress intensity factor concept and SINTAP structural integrity procedure are employed to assess gas pipelines integrity. The external longitudinal defects have been investigated via elastic-plastic finite element method results. The notch stress intensity concept is implemented into SINTAP procedure. The safety factor is calculated via SINTAP procedure levels 0B and 1B. The extracted evaluations are compared with the limit load analysis based on ASME B31G, modified ASME B31G, DNV RP-F101 and recent proposed formulation [Choi JB, Goo BK, Kim JC, Kim YJ, Kim WS. Development of limit load solutions for corroded gas pipelines. Int J Pressure Vessel Piping 2003;80(2):121-128]. The comparison among extracted safety factors exhibits that SINTAP predictions are located between lower and upper safety factor bounds. The SINTAP procedure including notch-based assessment diagram or so-called 'NFAD' involves wide range of defect geometries with low, moderate and high stress concentrations and relative stress gradients. Finally, some inspired and advanced viewpoints have been investigated

  18. Structural integrity evaluation of X52 gas pipes subjected to external corrosion defects using the SINTAP procedure

    Energy Technology Data Exchange (ETDEWEB)

    Adib-Ramezani, H. [Ecole Polytechnique de l' Universite d' Orleans, CNRS-CRMD, 8 rue Leonard de Vinci, 45072 Orleans Cedex 2 (France)]. E-mail: hradib_2000@yahoo.com; Jeong, J. [Ecole Polytechnique de l' Universite d' Orleans, CNRS-CRMD, 8 rue Leonard de Vinci, 45072 Orleans Cedex 2 (France); Pluvinage, G. [Laboratoire de Fiabilite Mecanique (LFM), Universite de Metz-ENIM, 57045 Metz (France)

    2006-06-15

    In the present study, the SINTAP procedure has been proposed as a general structural integrity tool for semi-spherical, semi-elliptical and long blunt notch defects. The notch stress intensity factor concept and SINTAP structural integrity procedure are employed to assess gas pipelines integrity. The external longitudinal defects have been investigated via elastic-plastic finite element method results. The notch stress intensity concept is implemented into SINTAP procedure. The safety factor is calculated via SINTAP procedure levels 0B and 1B. The extracted evaluations are compared with the limit load analysis based on ASME B31G, modified ASME B31G, DNV RP-F101 and recent proposed formulation [Choi JB, Goo BK, Kim JC, Kim YJ, Kim WS. Development of limit load solutions for corroded gas pipelines. Int J Pressure Vessel Piping 2003;80(2):121-128]. The comparison among extracted safety factors exhibits that SINTAP predictions are located between lower and upper safety factor bounds. The SINTAP procedure including notch-based assessment diagram or so-called 'NFAD' involves wide range of defect geometries with low, moderate and high stress concentrations and relative stress gradients. Finally, some inspired and advanced viewpoints have been investigated.

  19. An engineering assessment methodology for non-sharp defects in steel structures – Part I: Procedure development

    International Nuclear Information System (INIS)

    Horn, A.J.; Sherry, A.H.

    2012-01-01

    This Part I paper describes a new engineering assessment methodology for ferritic steel structures containing non-sharp defects within the context of a Failure Assessment Diagram (FAD) approach. Although the modification of the FAD for non-sharp defects can be applied whether the initiating failure mechanism is cleavage or ductile tearing, this paper focuses on cleavage fracture. The parameters describing the sensitivity of the material toughness to the notch effect can either be measured by testing notched specimens of the same thickness as the structure, or for cleavage fracture they can be obtained using look-up tables generated using the Weibull stress toughness scaling model. The other parameters in the procedure can either be conservatively estimated using simple equations or they can be determined more accurately using finite element analysis. Validation of the new method is presented in the companion Part II paper: this shows that assessments of U-notched SE(B) specimens have significantly reduced conservatism when using the new assessment methodology compared to the standard FAD approach for sharp cracks. - Highlights: ► Development of a new procedure for predicting failure from non-sharp defects. ► Based on a modification of the Failure Assessment Diagram (FAD) approach. ► Applicable to cleavage and ductile tearing initiation although paper focuses on cleavage. ► Validation provided in a companion Part II paper.

  20. The theory of dissipative structures of the kinetic system for defects of nonlinear physical system 'metal+loading+irradiation'. Part 3

    International Nuclear Information System (INIS)

    Tarasov, V.A.; Borikov, T.L.; Kryzhanovskaya, T.V.; Chernezhenko, S.A.; Rusov, V.D.

    2007-01-01

    The kinetic system for defects of physical nonlinear system 'metal + load + irradiation' is specified [1, 2, 3]. Developing the approaches offered in [4], where distinctions of mechanisms of radiating creep and areas of their applicability are formalized (depending on external parameters) for fuel and constructional metals, division of kinetic systems for defects of constructional and fuel metals is carrying out. Thus the accent on the autocatalytic features of kinetic system for defects of reactor fuel metals, resulting from the exoenergic autocatalytic character of nuclear fission reactions being the main point defect source is done. In this part of the article the basic attention is given to the kinetic of sink drains for point defects. For kinetic systems of sinks-sources new approaches for the task of boundary conditions are offered. The possible structure of the computer program modelling kinetic system for defects of nonlinear physical system 'metal + load + irradiation' is considered

  1. Effects of intrinsic defects on the electronic structure and magnetic properties of CoFe{sub 2}O{sub 4}: A first-principles study

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Y.L.; Fan, W.B. [School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang 330063 (China); Hou, Y.H., E-mail: hyhhyl@163.com [School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang 330063 (China); Guo, K.X. [School of Materials Science and Engineering, Nanchang Hangkong University, Nanchang 330063 (China); Ouyang, Y.F. [Department of Physics, Guangxi University, Nanning 530004 (China); Liu, Z.W. [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China)

    2017-05-01

    The cobalt ferrite (CoFe{sub 2}O{sub 4}) with spinel structure has achieved a great interest as a very important magnetic material which has covered a wide range of applications. The formation condition and energy of possible intrinsic point defects have been investigated by the first-principles calculations, and the effects of the intrinsic point defects on the electronic and magnetic properties of CoFe{sub 2}O{sub 4} have been analyzed. It is found that the growth conditions have a great effect on the formation energy of intrinsic point defects, and each point defect with its fully ionized state is the most stable for the intrinsic point defects with various charge states. In an oxygen rich environment, the cation vacancies are easy to form shallow acceptors, which is conducive to the strength of the p-type conductivity. While in the metal rich environment, the oxygen vacancies tend to form donors which lead to the n-type conductivity. There exists extra levels in the band gap when point defects are present, resulting in a reduction of the band gap. The net magnetic moment depends highly on the defects. - Highlights: • The intrinsic defects in CoFe{sub 2}O{sub 4} were investigated by first-principles calculation. • The effects of intrinsic defects on the electronic structures and magnetic properties of CoFe{sub 2}O{sub 4} were analyzed.

  2. Analysis of Manufacturing-Induced Defects and Structural Deformations in Lithium-Ion Batteries Using Computed Tomography

    Directory of Open Access Journals (Sweden)

    Yi Wu

    2018-04-01

    Full Text Available Premature battery drain, swelling and fires/explosions in lithium-ion batteries have caused wide-scale customer concerns, product recalls, and huge financial losses in a wide range of products including smartphones, laptops, e-cigarettes, hoverboards, cars, and commercial aircraft. Most of these problems are caused by defects which are difficult to detect using conventional nondestructive electrical methods and disassembly-based destructive analysis. This paper develops an effective computed tomography (CT-based nondestructive approach to assess battery quality and identify manufacturing-induced defects and structural deformations in batteries. Several unique case studies from commercial e-cigarette and smartphone applications are presented to show where CT analysis methods work.

  3. Structural defects in cilia of the choroid plexus, subfornical organ and ventricular ependyma are associated with ventriculomegaly

    Directory of Open Access Journals (Sweden)

    Swiderski Ruth E

    2012-10-01

    Full Text Available Abstract Background Hydrocephalus is a heterogeneous disorder with multiple etiologies that are not yet fully understood. Animal models have implicated dysfunctional cilia of the ependyma and choroid plexus in the development of the disorder. In this report, we sought to determine the origin of the ventriculomegaly in four Bardet Biedl syndrome (BBS mutant mouse strains as models of a ciliopathy. Methods Evans Blue dye was injected into the lateral ventricle of wild- type and BBS mutant mice to determine whether obstruction of intra- or extra-ventricular CSF flow contributed to ventriculomegaly. Transmission electron microscopy (TEM was used to examine the ultrastructure of the choroid plexus, subfornical organ (SFO, subcommisural organ (SCO, and ventricular ependyma to evaluate their ultrastructure and the morphology of their primary and motile cilia. Results and discussion No obstruction of intra- or extra-ventricular CSF flow was observed, implying a communicating form of hydrocephalus in BBS mutant mice. TEM analyses of the mutants showed no evidence of choroidal papillomas or breakdown of the blood:CSF barrier. In contrast, structural defects were observed in a subpopulation of cilia lining the choroid plexus, SFO, and ventricular ependyma. These included disruptions of the microtubular structure of the axoneme and the presence of electron-dense vesicular-like material along the ciliary shaft and at the tips of cilia. Conclusions Abnormalities in cilia structure and function have the potential to influence ciliary intraflagellar transport (IFT, cilia maintenance, protein trafficking, and regulation of CSF production. Ciliary structural defects are the only consistent pathological features associated with CSF-related structures in BBS mutant mice. These defects are observed from an early age, and may contribute to the underlying pathophysiology of ventriculomegaly.

  4. Electronic microscopy and EDX characterization of teotihuacan prehispanic mortar from the cave under the sun pyramid

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, T. [Faculty of Chemistry, National University of Mexico, Building D, CU (O4510) Mexico, D.F. (Mexico)]. E-mail: tmc@servidor.unam.mx; Martinez, G. [Coordinacion Nacional de Conservacion del Patrimonio Cultural. Xicontencatl y General Anaya s/n. (04120) Mexico, D.F. (Mexico); Mendoza, D. [National Institute of Nuclear Research.. Carr. Mexico-Toluca Km 36.5 (52045), Salazar, Ocoyoacac, Edo. de Mexico (Mexico); Juarez, F. [Institute of Geophysics, National University of Mexico, Circuito Institutos, CU (04510) Mexico, D.F. (Mexico); Cabrera, L. [Faculty of Chemistry, National University of Mexico, Building D, CU (O4510) Mexico, D.F. (Mexico)

    2005-12-01

    A cave (102 m long) under the structure of the Sun pyramid of the prehispanic Teotihuacan City indicates the importance of the pyramid. Studies of the cave mortar samples using energy dispersive X-ray (EDX) fluorescence, scanning electron microscopy (SEM) and X-ray diffraction (XRD) showed no difference in the chemical elemental composition. The elements can be distributed in three groups: major, minor and trace elements. The minerals identified were compatible with the origins of the cave and with the magnetic pattern.

  5. Point defects in solids

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    The principal properties of point defects are studied: thermodynamics, electronic structure, interactions with etended defects, production by irradiation. Some measuring methods are presented: atomic diffusion, spectroscopic methods, diffuse scattering of neutron and X rays, positron annihilation, molecular dynamics. Then points defects in various materials are investigated: ionic crystals, oxides, semiconductor materials, metals, intermetallic compounds, carbides, nitrides [fr

  6. Cooperative RNP assembly: Complementary rescue of structural defects by protein and RNA subunits of archaeal RNase P

    Science.gov (United States)

    Chen, Wen-Yi; Xu, Yiren; Cho, I-Ming; Oruganti, Sri Vidya; Foster, Mark P.; Gopalan, Venkat

    2011-01-01

    RNase P is a ribonucleoprotein (RNP) complex that utilizes a Mg2+-dependent RNA catalyst to cleave the 5′-leader of precursor tRNAs (pre-tRNAs) and generate mature tRNAs. The bacterial RNase P protein (RPP) aids RNase P RNA (RPR) catalysis by promoting substrate binding, Mg2+ coordination, and product release. Archaeal RNase P comprises an RPR and at least four RPPs, which have eukaryal homologs and function as two binary complexes (POP5•RPP30 and RPP21•RPP29). In this study, we employed a previously characterized substrate-enzyme conjugate [pre-tRNATyr-Methanocaldococcus jannaschii (Mja) RPR] to investigate the functional role of a universally conserved uridine in a bulge-helix structure in archaeal RPRs. Deletion of this bulged uridine resulted in an 80-fold decrease in the self-cleavage rate of pre-tRNATyr-MjaΔU RPR compared to the wildtype, and this defect was partially ameliorated upon addition of either RPP pair. The catalytic defect in the archaeal mutant RPR mirrors that reported in a bacterial RPR and highlights a parallel in their active sites. Furthermore, an N-terminal deletion mutant of Pyrococcus furiosus (Pfu) RPP29 that is defective in assembling with its binary partner RPP21, as assessed by isothermal titration calorimetry and NMR spectroscopy, is functional when reconstituted with the cognate Pfu RPR. Collectively, these results indicate that archaeal RPPs are able to compensate for structural defects in their cognate RPR and vice-versa, and provide striking examples of the cooperative subunit interactions critical for driving archaeal RNase P towards its functional conformation. (236 words) PMID:21683084

  7. Variable low energy positron beams for depth resolved defect spectroscopy in thin film structures

    International Nuclear Information System (INIS)

    Amarendra, G.; Viswanathan, B.; Venugopal Rao, G.; Parimala, J.; Purniah, B.

    1997-01-01

    The design, development and commissioning details of an ultra high vacuum compatible, magnetically-guided and compact variable low energy positron beam facility are reported. Information pertaining to the nature, concentration and spatial distribution of defects present at various depths in the near-surface layers of a material can be obtained using this technique. Some of the experimental results obtained using this facility, in terms of surface-sensitive positronium fraction measurements on Cu surfaces as well as defect-sensitive Doppler broadening measurements on semiconductor interfaces and ion irradiated silicon are presented. These results essentially provide an illustration of the research capability of the technique for the study of sub-surface regions and thin film interfaces. (author)

  8. On the defect structure due to low energy ion bombardment of graphite

    Science.gov (United States)

    Marton, D.; Bu, H.; Boyd, K. J.; Todorov, S. S.; Al-Bayati, A. H.; Rabalais, J. W.

    1995-03-01

    Graphite surfaces cleaved perpendicular to the c axis have been irradiated with low doses of Ar + ions at 50 eV kinetic energy and perpendicular incidence. Scanning tunneling micrographs (STM) of these irradiated surfaces exhibited dome-like features as well as point defects. These dome-like features retain undisturbed graphite periodicity. This finding is attributed to the stopping of ions between the first and second graphite sheets. The possibility of doping semiconductors at extremely shallow depths is raised.

  9. The influence of the defect structure on the nitriding of Fe by PIII

    Czech Academy of Sciences Publication Activity Database

    Jirásková, Yvonna; De Baerdemaeker, Jeremie; Schaaf, P.; Segers, D.; Dauwe, Ch.

    2005-01-01

    Roč. 107, č. 5 (2005), s. 817-820 ISSN 0587-4246. [Polish Seminar on Positron Annihilation /35./. Turawa, 20.09.2004-24.09.2004] R&D Projects: GA MŠk ME 645 Institutional research plan: CEZ:AV0Z20410507 Keywords : defect * positron annihilation * nanointendation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.394, year: 2005

  10. Texture-based segmentation with Gabor filters, wavelet and pyramid decompositions for extracting individual surface features from areal surface topography maps

    International Nuclear Information System (INIS)

    Senin, Nicola; Leach, Richard K; Pini, Stefano; Blunt, Liam A

    2015-01-01

    Areal topography segmentation plays a fundamental role in those surface metrology applications concerned with the characterisation of individual topography features. Typical scenarios include the dimensional inspection and verification of micro-structured surface features, and the identification and characterisation of localised defects and other random singularities. While morphological segmentation into hills or dales is the only partitioning operation currently endorsed by the ISO specification standards on surface texture metrology, many other approaches are possible, in particular adapted from the literature on digital image segmentation. In this work an original segmentation approach is introduced and discussed, where topography partitioning is driven by information collected through the application of texture characterisation transforms popular in digital image processing. Gabor filters, wavelets and pyramid decompositions are investigated and applied to a selected set of test cases. The behaviour, performance and limitations of the proposed approach are discussed from the viewpoint of the identification and extraction of individual surface topography features. (paper)

  11. Current Evidence for Developmental, Structural, and Functional Brain Defects following Prenatal Radiation Exposure

    Directory of Open Access Journals (Sweden)

    Tine Verreet

    2016-01-01

    Full Text Available Ionizing radiation is omnipresent. We are continuously exposed to natural (e.g., radon and cosmic and man-made radiation sources, including those from industry but especially from the medical sector. The increasing use of medical radiation modalities, in particular those employing low-dose radiation such as CT scans, raises concerns regarding the effects of cumulative exposure doses and the inappropriate utilization of these imaging techniques. One of the major goals in the radioprotection field is to better understand the potential health risk posed to the unborn child after radiation exposure to the pregnant mother, of which the first convincing evidence came from epidemiological studies on in utero exposed atomic bomb survivors. In the following years, animal models have proven to be an essential tool to further characterize brain developmental defects and consequent functional deficits. However, the identification of a possible dose threshold is far from complete and a sound link between early defects and persistent anomalies has not yet been established. This review provides an overview of the current knowledge on brain developmental and persistent defects resulting from in utero radiation exposure and addresses the many questions that still remain to be answered.

  12. X-ray analysis of temperature induced defect structures in boron implanted silicon

    Science.gov (United States)

    Sztucki, M.; Metzger, T. H.; Kegel, I.; Tilke, A.; Rouvière, J. L.; Lübbert, D.; Arthur, J.; Patel, J. R.

    2002-10-01

    We demonstrate the application of surface sensitive diffuse x-ray scattering under the condition of grazing incidence and exit angles to investigate growth and dissolution of near-surface defects after boron implantation in silicon(001) and annealing. Silicon wafers were implanted with a boron dose of 6×1015 ions/cm2 at 32 keV and went through different annealing treatments. From the diffuse intensity close to the (220) surface Bragg peak we reveal the nature and kinetic behavior of the implantation induced defects. Analyzing the q dependence of the diffuse scattering, we are able to distinguish between point defect clusters and extrinsic stacking faults on {111} planes. Characteristic for stacking faults are diffuse x-ray intensity streaks along directions, which allow for the determination of their growth and dissolution kinetics. For the annealing conditions of our crystals, we conclude that the kinetics of growth can be described by an Ostwald ripening model in which smaller faults shrink at the expense of the larger stacking faults. The growth is found to be limited by the self-diffusion of silicon interstitials. After longer rapid thermal annealing the stacking faults disappear almost completely without shrinking, most likely by transformation into perfect loops via a dislocation reaction. This model is confirmed by complementary cross-sectional transmission electron microscopy.

  13. Critical current, pinning and resistive state of superconducting single-crystal niobium with different types of defect structure

    International Nuclear Information System (INIS)

    Sokolenko, V.I.; Starodubov, Ya.D.

    2005-01-01

    Critical current pinning and resistive state of single crystal niobium of texture orientation are studied for different structural states obtained by rolling at 20 K by 42% and polishing the surface layers. It is found that the heterogeneous structures typical of the strained sample even after its thinning down to approx 10% display a lower current-carrying capability due to an increase of the thermomagnetic instability within the fragmented structure sections in the near-surface layers. For a homogeneous defect structure of the sample core with the density of equilibrium distributed dislocations of 1.3 centre dot 10 11 cm -2 , a correlation between the normal current density and the critical current density in the resistive state is found, in agreement with the concepts of flux creep due to the scatter of local values of J c

  14. High density micro-pyramids with silicon nanowire array for photovoltaic applications

    International Nuclear Information System (INIS)

    Rahman, Tasmiat; Navarro-Cía, Miguel; Fobelets, Kristel

    2014-01-01

    We use a metal assisted chemical etch process to fabricate silicon nanowire arrays (SiNWAs) onto a dense periodic array of pyramids that are formed using an alkaline etch masked with an oxide layer. The hybrid micro-nano structure acts as an anti-reflective coating with experimental reflectivity below 1% over the visible and near-infrared spectral regions. This represents an improvement of up to 11 and 14 times compared to the pyramid array and SiNWAs on bulk, respectively. In addition to the experimental work, we optically simulate the hybrid structure using a commercial finite difference time domain package. The results of the optical simulations support our experimental work, illustrating a reduced reflectivity in the hybrid structure. The nanowire array increases the absorbed carrier density within the pyramid by providing a guided transition of the refractive index along the light path from air into the silicon. Furthermore, electrical simulations which take into account surface and Auger recombination show an efficiency increase for the hybrid structure of 56% over bulk, 11% over pyramid array and 8.5% over SiNWAs. (paper)

  15. Vacancy-type defects in Al2O3/GaN structure probed by monoenergetic positron beams

    Science.gov (United States)

    Uedono, Akira; Nabatame, Toshihide; Egger, Werner; Koschine, Tönjes; Hugenschmidt, Christoph; Dickmann, Marcel; Sumiya, Masatomo; Ishibashi, Shoji

    2018-04-01

    Defects in the Al2O3(25 nm)/GaN structure were probed by using monoenergetic positron beams. Al2O3 films were deposited on GaN by atomic layer deposition at 300 °C. Temperature treatment above 800 °C leads to the introduction of vacancy-type defects in GaN due to outdiffusion of atoms from GaN into Al2O3. The width of the damaged region was determined to be 40-50 nm from the Al2O3/GaN interface, and some of the vacancies were identified to act as electron trapping centers. In the Al2O3 film before and after annealing treatment at 300-900 °C, open spaces with three different sizes were found to coexist. The density of medium-sized open spaces started to decrease above 800 °C, which was associated with the interaction between GaN and Al2O3. Effects of the electron trapping/detrapping processes of interface states on the flat band voltage and the defects in GaN were also discussed.

  16. Relations between anisotropic defects, structural evolution, and van der Waals bonding in 2H-NbSe2

    International Nuclear Information System (INIS)

    Gavarri, J.R.; Mokrani, R.; Boulesteix, C.; Vacquier, G.

    1988-01-01

    Correlations between anisotropic defects and van der Waals interactions have been established for the layer compound 2H-NbSe 2 which is investigated by low temperature X-ray diffraction techniques. Thermal expansion coefficients and anisotropic Debye temperatures are determined. A diffraction profile analysis reveals the existence of lattice distortions independent of the temperature. They are due to layer defects. To interpret the structural evolution data, the thermal expansion functions, α a (T) and α c (T) are simulated in the low temperature range which yield the elastic constants and the Grueneisen parameters. Using bond energy models, the Van der Waals nature of interlayer Se-Se interactions is confirmed by a model of thermal expansion of bonds and connected with the C 13 component of the elastic tensor. Such interactions can explain the presence of some layer defects that can be 4H-NbSe 2 nuclei in the 2H host lattice. In addition, no strong change in the Grueneisen parameters is clearly shown to occur at the 35 K transition of 2H-NbSe 2 . (author)

  17. The roles of the temperature on the structural and electronic properties of deep-level V{sub As}V{sub Ga} defects in gallium arsenide

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Deming, E-mail: xautmdm@163.com; Chen, Xi; Qiao, Hongbo; Shi, Wei; Li, Enling

    2015-07-15

    Highlights: • The energy gap of the Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} is 0.82 eV. • Proves that the Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} belongs to EL2 deep-level defect in GaAs. • Proves that EL2 and EL6 deep-level defects can transform into each other. • Temperature has an important effect on the microstructure of deep-level defects. - Abstract: The roles of temperature on the structural and electronic properties of V{sub As}V{sub Ga} defects in gallium arsenide have been studied by using ab-initio molecular dynamic (MD) simulation. Our calculated results show that the relatively stable quaternary complex defect of Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} can be converted from the V{sub As}V{sub Ga} complex clusters defect between 300 K and 1173 K; however, from 1173 K to 1373 K, the decomposition of the complex defect Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} occurs, turning into a deep-level V{sub As}V{sub Ga} cluster defect and an isolated As{sub Ga} antisite defect, and relevant defect of Ga{sub As} is recovered. The properties of Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} defect has been studied by first-principles calculations based on hybrid density functional theory. Our calculated results show that the Ga{sub As}As{sub Ga}V{sub As}V{sub Ga} belongs to EL2 deep-level defect in GaAs. Thus, we reveal that the temperature has an important effect on the microstructure of deep-level defects and defect energy level in gallium arsenide that EL2 and EL6 deep-level defects have a certain correlation, which means they could transform into each other. Controlling temperature in the growth process of GaAs could change the microstructure of deep-level defects and defect energy levels in gallium arsenide materials, whereby affects the electron transport properties of materials.

  18. Birth–death process of local structures in defect turbulence described by the one-dimensional complex Ginzburg–Landau equation

    Energy Technology Data Exchange (ETDEWEB)

    Uchiyama, Yusuke, E-mail: r1230160@risk.tsukuba.ac.jp; Konno, Hidetoshi

    2014-04-01

    Defect turbulence described by the one-dimensional complex Ginzburg–Landau equation is investigated and analyzed via a birth–death process of the local structures composed of defects, holes, and modulated amplitude waves (MAWs). All the number statistics of each local structure, in its stationary state, are subjected to Poisson statistics. In addition, the probability density functions of interarrival times of defects, lifetimes of holes, and MAWs show the existence of long-memory and some characteristic time scales caused by zigzag motions of oscillating traveling holes. The corresponding stochastic process for these observations is fully described by a non-Markovian master equation.

  19. Electronic and atomic structure of complex defects in Al- and Ga-highly doped ZnO films

    Energy Technology Data Exchange (ETDEWEB)

    Menéndez-Proupin, Eduardo [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Departamento de Física, Facultad de Ciencias, Universidad de Chile, Las Palmeras 3425, 780-0003 Ñuñoa, Santiago (Chile); Palacios, Pablo, E-mail: pablo.palacios@upm.es [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Dpt. FAIAN, E.T.S.I. Aeronáutica y del Espacio, UPM, Pz. Cardenal Cisneros 3, 28040 Madrid (Spain); Wahnón, Perla [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Dpt. TFO, E.T.S.I. Telecomunicación, UPM, Ciudad Universitaria, 28040 Madrid (Spain)

    2015-06-15

    Point defects in Ga- and Al-doped ZnO thin films are studied by means of first principles electronic structure calculations. Candidate defects are identified to explain recently observed differences in electrical and spectroscopic behavior of both systems. Substitutional doping in Ga–ZnO explain the metallic behavior of the electrical properties. Complexes of interstitial oxygen with substitutional Ga can behave as acceptor and cause partial compensation, as well as gap states below the conduction band minimum as observed in photoemission experiments. Zn vacancies can also act as compensating acceptors. On the other hand, the semiconducting behavior of Al–ZnO and the small variation in the optical gap compared with pure ZnO, can be explained by almost complete compensation between acceptor Zn vacancies and substitutional Al donors. Interstitial Al can also be donor levels and can be the origin of the small band observed in photoemission experiments below the Fermi level. Combinations of substitutional Al with interstitial oxygen can act simultaneously as compensating acceptor and generator of the mentioned photoemission band. The theoretical calculations have been done using density functional theory (DFT) within the generalized gradient approximation with on-site Coulomb interaction. In selected cases, DFT calculations with semilocal-exact exchange hybrid functionals have been performed. Results explain photoelectron spectra of Ga–ZnO and Al–ZnO at the corresponding doping levels. - Highlights: • Defects in Ga- and Al-heavy-doped ZnO films are studied by quantum calculations. • Defects compatible with electrical, optical, and HAXPES spectra are proposed. • Doping efficiency is reduced by Zn vacancies and O interstitials. • HAXPES bands near the Fermi level are induced by Al{sub i}, and complexes Ga{sub Zn}-O{sub i}, and Al{sub Zn}-O{sub i}.

  20. Alpha-particle irradiation induced defects in SiO2 films of Si-SiO2 structures

    International Nuclear Information System (INIS)

    Koman, B.P.; Gal'chynskyy, O.V.; Kovalyuk, R.O.; Shkol'nyy, A.K.

    1996-01-01

    The aim of the work was to investigate alpha-particle irradiation induced defects in Si-SiO 2 structures by means of the thermostimulated discharge currents (TSDC) analysis. The object of investigation were (p-Si)-SiO 2 structures formed by a combined oxidation of the industrial p-Si wafers in dry and wet oxygen at temperature of 1150 C. The TSD currents were investigated in the temperature range between 90 and 500 K under linear heating rate. Pu 238 isotopes were the source of alpha-particles with an energy of 4-5 MeV and a density of 5.10 7 s -1 cm -2 . The TSD current curves show two peculiar maxima at about 370 and 480 K. Alpha-particle irradiation doesn't affect the general shape of the TSDC curves but leads to a shift of the maximum at 370 K and reduces the total electret charge which is accumulated in the Si-SiO 2 structures during polarization. The energy distribution function of the defects which are involved in SiO 2 polarization has been calculated. It showes that defects with activation energies of about 0.8 and 1.0 eV take part in forming the electret state, and these activation energies have certain energy distributions. It has been found that the TSDC maximum at 370 K has space charge nature and is caused by migration of hydrogen ions. In irradiated samples hydrogen and natrium ions localize on deeper trapping centres induced by alpha-particle irradiation. (orig.)

  1. Study of the defect structure of ''pure'' and doped nonstoichiometric CeO2

    International Nuclear Information System (INIS)

    Blumenthal, R.N.

    1975-09-01

    Electrical conductivity and thermogravimetric measurements were made on Ta 2 O 5 -doped nonstoichiometric CeO 2 (i.e. Ce/sub 1-y/Ta/sub y/O/sub 2-x/ ) as a function of temperature and oxygen partial pressure. Over a limited range of temperature and nonstoichiometry, the isothermal dependence of the electrical conductivity on nonstoichiometry may be described by the equation sigma = A + Bx, where A is the electronic conductivity associated with the electronic defects produced by doping CeO 2 with Ta 2 O 5 . The electronic conductivity resulting from the nonstoichiometric defect reaction O/sup x/ + 2Ce/sub Ce//sup x/ = V 0 + 2Ce'sub Ce/ + 1 / 2 O 2 (g) is equal to Bx. The ionic conductivity may be described by the relation sigma/sub i/ = B[y+x]eμ'/sub V 0 / exp (--E/sub i//kT), and the electronic conductivity by the isothermal expressions sigma/sub e/ proportional to P/sub O 2 //sup -1/4/ and sigma/sub e/ proportional to x; x less than 3 x 10 -2 . These results are consistent with defect models involving doubly ionized oxygen vacancies. An empirical expression (i.e. Δ anti H/sub O 2 / proportional to y/2 or z/4) was obtained relating the dependence of Δ anti H/sub O 2 / on the dopant concentration of lower valent foreign cations (e.g. y/2 for Ce/sub 1-y/M/sub y/O/sub 2-y-x/ and z/4 for Ce/sub 1-z/M/sub z/O/sub 2-z/2-x/ where M = Ca, Sr and M' = Y, La). (auth)

  2. DLTS and capacitance transients study of defects induced by neutron irradiation in MOS structures CCD process

    International Nuclear Information System (INIS)

    Ahaitouf, A.; Losson, E.; Charles, J.P.

    1999-01-01

    The aim of this paper is to study neutron irradiation effects on PMOS capacitors and NMOSFETs transistors. The characterization of induced defects was made by capacitance transients C(t) measurements, DLTS spectroscopy, and optical DLTS (ODLTS). DLTS spectra present three peaks due to deep levels created in the semiconductor and two peaks due to minority carrier generation. Two levels are reported in the literature. Two other minority carrier traps have been observed on ODLTS spectra after irradiation. This can explain the decrease of the minority carrier generation lifetime observed by capacitance transients measurements. (authors)

  3. Indium–gallium–zinc oxide thin film transistors with a hybrid-channel structure for defect suppression and mobility improvement

    International Nuclear Information System (INIS)

    Lin, Huang-Kai; Su, Liang-Yu; Hung, Chia-Chin; Huang, JianJang

    2013-01-01

    In this work, we explore an indium gallium zinc oxide (IGZO) thin film transistor structure with a vacuum annealed IGZO thin film inserted between the dielectric and typical channel layers. The device demonstrates a better subthreshold swing and field-effect mobility due to the suppression of defects in the channel and the channel/dielectric interface. The hybrid channel structure also exhibits the flexibility of adjusting the threshold voltage. The superior carrier mobility was then verified from the transient response of the inverter circuit constructed by the devices. - Highlights: • Additional in-situ annealed In–Ga–ZnO film was inserted in thin film transistor (TFT). • Traps are suppressed and field effect mobility is improved in the TFT. • An inverter with the device structure has a better transient response

  4. Indium–gallium–zinc oxide thin film transistors with a hybrid-channel structure for defect suppression and mobility improvement

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Huang-Kai; Su, Liang-Yu; Hung, Chia-Chin [Graduate Institute of Photonics and Optoelectronics, National Taiwan University, 1, Roosevelt Road, Sec. 4, Taipei 106, Taiwan (China); Huang, JianJang, E-mail: jjhuang@cc.ee.ntu.edu.tw [Graduate Institute of Photonics and Optoelectronics, National Taiwan University, 1, Roosevelt Road, Sec. 4, Taipei 106, Taiwan (China); Department of Electrical Engineering, National Taiwan University, 1, Roosevelt Road, Sec. 4, Taipei 106, Taiwan (China)

    2013-07-01

    In this work, we explore an indium gallium zinc oxide (IGZO) thin film transistor structure with a vacuum annealed IGZO thin film inserted between the dielectric and typical channel layers. The device demonstrates a better subthreshold swing and field-effect mobility due to the suppression of defects in the channel and the channel/dielectric interface. The hybrid channel structure also exhibits the flexibility of adjusting the threshold voltage. The superior carrier mobility was then verified from the transient response of the inverter circuit constructed by the devices. - Highlights: • Additional in-situ annealed In–Ga–ZnO film was inserted in thin film transistor (TFT). • Traps are suppressed and field effect mobility is improved in the TFT. • An inverter with the device structure has a better transient response.

  5. Defects in pipe supports attached to concrete structures at Finnish nuclear power plants

    International Nuclear Information System (INIS)

    Nykaenen, J.E.; Reponen, H.; Suominen, J.

    1981-01-01

    The Installation defects in expansion anchors of pipe supports detected in Sweden attracted the attention of the Finnish nuclear authority, the IRP in the autumm of 1979. No serious deficiencies were found at TVO I and II units where expansion anchors tightened by torguing are used. Preliminary inspections at Lo 2 construction plant revealed a great number of defectively installed expansion anchors of the type which is tightened by hitting. This resulted in placing Lo 1 unit into a cold shut-down condition for inspections and reparation. The shut-down lasted for three weeks during which time, in rooms inaccessible during operation, about 2000 expansion anchors were checked and 95% of them repaired or modified. After running up Lo 1 unit, the work continued in accessible rooms and at Lo2 unit for several months. The main fault was the failure to hit the anchor wedge deep enough into its cylinder. A contributing factor may have been too small hole diameters. The anchor tensile tests conducted at the site proved that the insufficient penetration of the wedge drastically reduces the load capacity. (orig./GL)

  6. Structural Testing of the Blade Reliability Collaborative Effect of Defect Wind Turbine Blades

    Energy Technology Data Exchange (ETDEWEB)

    Desmond, M. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hughes, S. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Paquette, J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-06-08

    Two 8.3-meter (m) wind turbine blades intentionally constructed with manufacturing flaws were tested to failure at the National Wind Technology Center (NWTC) at the National Renewable Energy Laboratory (NREL) south of Boulder, Colorado. Two blades were tested; one blade was manufactured with a fiberglass spar cap and the second blade was manufactured with a carbon fiber spar cap. Test loading primarily consisted of flap fatigue loading of the blades, with one quasi-static ultimate load case applied to the carbon fiber spar cap blade. Results of the test program were intended to provide the full-scale test data needed for validation of model and coupon test results of the effect of defects in wind turbine blade composite materials. Testing was part of the Blade Reliability Collaborative (BRC) led by Sandia National Laboratories (SNL). The BRC seeks to develop a deeper understanding of the causes of unexpected blade failures (Paquette 2012), and to develop methods to enable blades to survive to their expected operational lifetime. Recent work in the BRC includes examining and characterizing flaws and defects known to exist in wind turbine blades from manufacturing processes (Riddle et al. 2011). Recent results from reliability databases show that wind turbine rotor blades continue to be a leading contributor to turbine downtime (Paquette 2012).

  7. Electronic structures of β-SiC containing point defects studied by DX-Xα method

    International Nuclear Information System (INIS)

    Sawabe, Takashi; Yano, Toyohiko

    2008-01-01

    The DV-Xα method was used to calculate the bond order between atoms in cubic silicon carbide (β-SiC) with a point defect. Three types of β-SiC cluster models were used: pure cluster, vacancy cluster and interstitial cluster. The bond order was influenced by the kind to defects. The bonds between C interstitial and neighboring C atoms were composed of anti-bonding type interactions, while the bonds between Si interstitial and neighboring C and Si atoms were composed of bonding type interactions. The overlap population of each molecular orbital was examined to obtain detailed information of the chemical bonding. It appeared more difficult to recombine interstitial atoms in a cluster with a C atom vacancy than in a cluster with a Si atom vacancy, due to the stronger Si-Si bonds surrounding the C atom vacancy. The C interstitial atom had C2s and C2p anti-bonding interactions with high energy levels. The Si interstitial had minimal anti-bonding interactions. (author)

  8. Content-adaptive pyramid representation for 3D object classification

    DEFF Research Database (Denmark)

    Kounalakis, Tsampikos; Boulgouris, Nikolaos; Triantafyllidis, Georgios

    2016-01-01

    In this paper we introduce a novel representation for the classification of 3D images. Unlike most current approaches, our representation is not based on a fixed pyramid but adapts to image content and uses image regions instead of rectangular pyramid scales. Image characteristics, such as depth...... and color, are used for defining regions within images. Multiple region scales are formed in order to construct the proposed pyramid image representation. The proposed method achieves excellent results in comparison to conventional representations....

  9. XAFS study of copper(II) complexes with square planar and square pyramidal coordination geometries

    Science.gov (United States)

    Gaur, A.; Klysubun, W.; Nitin Nair, N.; Shrivastava, B. D.; Prasad, J.; Srivastava, K.

    2016-08-01

    X-ray absorption fine structure of six Cu(II) complexes, Cu2(Clna)4 2H2O (1), Cu2(ac)4 2H2O (2), Cu2(phac)4 (pyz) (3), Cu2(bpy)2(na)2 H2O (ClO4) (4), Cu2(teen)4(OH)2(ClO4)2 (5) and Cu2(tmen)4(OH)2(ClO4)2 (6) (where ac, phac, pyz, bpy, na, teen, tmen = acetate, phenyl acetate, pyrazole, bipyridine, nicotinic acid, tetraethyethylenediamine, tetramethylethylenediamine, respectively), which were supposed to have square pyramidal and square planar coordination geometries have been investigated. The differences observed in the X-ray absorption near edge structure (XANES) features of the standard compounds having four, five and six coordination geometry points towards presence of square planar and square pyramidal geometry around Cu centre in the studied complexes. The presence of intense pre-edge feature in the spectra of four complexes, 1-4, indicates square pyramidal coordination. Another important XANES feature, present in complexes 5 and 6, is prominent shoulder in the rising part of edge whose intensity decreases in the presence of axial ligands and thus indicates four coordination in these complexes. Ab initio calculations were carried out for square planar and square pyramidal Cu centres to observe the variation of 4p density of states in the presence and absence of axial ligands. To determine the number and distance of scattering atoms around Cu centre in the complexes, EXAFS analysis has been done using the paths obtained from Cu(II) oxide model and an axial Cu-O path from model of a square pyramidal complex. The results obtained from EXAFS analysis have been reported which confirmed the inference drawn from XANES features. Thus, it has been shown that these paths from model of a standard compound can be used to determine the structural parameters for complexes having unknown structure.

  10. Sonographic findings in primary diseases of renal pyramids

    International Nuclear Information System (INIS)

    Rao, B.K.

    1987-01-01

    Primary pathologic processes involving the renal pyramids such as papillary necrosis, drug-induced necrosis or calcinosis, cysts, neoplasms, and medullary nephrocalcinosis are rare. Thirty-four patients with primary renal pyramid diseases underwent US evaluation for altered morphology; a 5-MHz transducer was used. In 20 patients site-specific changes in the pyramid (e.g., papillary necrosis at the apex, small cysts at the base in medullary cystic disease, tubular calcification in MSK, corticomedullary hyperechogenicity in oxalosis) were noted on US. Sonographic delineation of the site and pattern of pathologic changes in the renal pyramid may help to identify specific diseases

  11. Effect of housing rats within a pyramid on stress parameters.

    Science.gov (United States)

    Bhat, Surekha; Rao, Guruprasad; Murthy, K Dilip; Bhat, P Gopalakrishna

    2003-11-01

    The Giza pyramids of Egypt have been the subject of much research. Pyramid models with the same base to height ratio as of the Great Pyramid of Giza, when aligned on a true north-south axis, are believed to generate, transform and transmit energy. Research done with such pyramid models has shown that they induced greater relaxation in human subjects, promoted better wound healing in rats and afforded protection against stress-induced neurodegnerative changes in mice. The present study was done to assess the effects of housing Wistar rats within the pyramid on the status of oxidative damage and antioxidant defense in their erythrocytes and cortisol levels in their plasma. Rats were housed in cages under standard laboratory conditions. Cages were left in the open (normal control), under a wooden pyramid model (experimental rats) or in a cubical box of comparable dimensions (6 hr/day for 14 days). Erythrocyte malondialdehyde and plasma cortisol levels were significantly decreased in rats kept within the pyramid as compared to the normal control and those within the square box. Erythrocyte reduced glutathione levels, erythrocyte glutathione peroxidase and superoxide dismutase activities were significantly increased in the rats kept in the pyramid as compared to the other two groups. There was no significant difference in any of the parameters between the normal control and rats kept in the square box. The results showed that exposure of adult female Wistar rats to pyramid environment reduces stress oxidative stress and increases antioxidant defense in them.

  12. Importance of doping, dopant distribution, and defects on electronic band structure alteration of metal oxide nanoparticles: Implications for reactive oxygen species

    International Nuclear Information System (INIS)

    Saleh, Navid B.; Milliron, Delia J.; Aich, Nirupam; Katz, Lynn E.; Liljestrand, Howard M.; Kirisits, Mary Jo

    2016-01-01

    Metal oxide nanoparticles (MONPs) are considered to have the potency to generate reactive oxygen species (ROS), one of the key mechanisms underlying nanotoxicity. However, the nanotoxicology literature demonstrates a lack of consensus on the dominant toxicity mechanism(s) for a particular MONP. Moreover, recent literature has studied the correlation between band structure of pristine MONPs to their ability to introduce ROS and thus has downplayed the ROS-mediated toxicological relevance of a number of such materials. On the other hand, material science can control the band structure of these materials to engineer their electronic and optical properties and thereby is constantly modulating the pristine electronic structure. Since band structure is the fundamental material property that controls ROS-producing ability, band tuning via introduction of dopants and defects needs careful consideration in toxicity assessments. This commentary critically evaluates the existing material science and nanotoxicity literature and identifies the gap in our understanding of the role of important crystal structure features (i.e., dopants and defects) on MONPs' electronic structure alteration as well as their ROS-generation capability. Furthermore, this commentary provides suggestions on characterization techniques to evaluate dopants and defects on the crystal structure and identifies research needs for advanced theoretical predictions of their electronic band structures and ROS-generation abilities. Correlation of electronic band structure and ROS will not only aid in better mechanistic assessment of nanotoxicity but will be impactful in designing and developing ROS-based applications ranging from water disinfection to next-generation antibiotics and even cancer therapeutics. - Highlights: • Metal oxide nanoparticles (MONPs) produce reactive oxygen species (ROS) • Band structure of pristine MONPs is different than those with dopants/defects • Dopants/defects modulate

  13. Importance of doping, dopant distribution, and defects on electronic band structure alteration of metal oxide nanoparticles: Implications for reactive oxygen species

    Energy Technology Data Exchange (ETDEWEB)

    Saleh, Navid B., E-mail: navid.saleh@utexas.edu [Department of Civil, Architectural, and Environmental Engineering, University of Texas, Austin, TX 78712 (United States); Milliron, Delia J. [McKetta Department of Chemical Engineering, University of Texas, Austin, TX 78712 (United States); Aich, Nirupam [Department of Civil, Structural and Environmental Engineering, University at Buffalo, The State University of New York, Buffalo, NY, 14260 (United States); Katz, Lynn E.; Liljestrand, Howard M.; Kirisits, Mary Jo [Department of Civil, Architectural, and Environmental Engineering, University of Texas, Austin, TX 78712 (United States)

    2016-10-15

    Metal oxide nanoparticles (MONPs) are considered to have the potency to generate reactive oxygen species (ROS), one of the key mechanisms underlying nanotoxicity. However, the nanotoxicology literature demonstrates a lack of consensus on the dominant toxicity mechanism(s) for a particular MONP. Moreover, recent literature has studied the correlation between band structure of pristine MONPs to their ability to introduce ROS and thus has downplayed the ROS-mediated toxicological relevance of a number of such materials. On the other hand, material science can control the band structure of these materials to engineer their electronic and optical properties and thereby is constantly modulating the pristine electronic structure. Since band structure is the fundamental material property that controls ROS-producing ability, band tuning via introduction of dopants and defects needs careful consideration in toxicity assessments. This commentary critically evaluates the existing material science and nanotoxicity literature and identifies the gap in our understanding of the role of important crystal structure features (i.e., dopants and defects) on MONPs' electronic structure alteration as well as their ROS-generation capability. Furthermore, this commentary provides suggestions on characterization techniques to evaluate dopants and defects on the crystal structure and identifies research needs for advanced theoretical predictions of their electronic band structures and ROS-generation abilities. Correlation of electronic band structure and ROS will not only aid in better mechanistic assessment of nanotoxicity but will be impactful in designing and developing ROS-based applications ranging from water disinfection to next-generation antibiotics and even cancer therapeutics. - Highlights: • Metal oxide nanoparticles (MONPs) produce reactive oxygen species (ROS) • Band structure of pristine MONPs is different than those with dopants/defects • Dopants/defects modulate

  14. Pyramid algorithms as models of human cognition

    Science.gov (United States)

    Pizlo, Zygmunt; Li, Zheng

    2003-06-01

    There is growing body of experimental evidence showing that human perception and cognition involves mechanisms that can be adequately modeled by pyramid algorithms. The main aspect of those mechanisms is hierarchical clustering of information: visual images, spatial relations, and states as well as transformations of a problem. In this paper we review prior psychophysical and simulation results on visual size transformation, size discrimination, speed-accuracy tradeoff, figure-ground segregation, and the traveling salesman problem. We also present our new results on graph search and on the 15-puzzle.

  15. Layered sphere-shaped TiO₂ capped with gold nanoparticles on structural defects and their catalysis of formaldehyde oxidation.

    Science.gov (United States)

    Ma, Chunyan; Pang, Guanglong; He, Guangzhi; Li, Yang; He, Chi; Hao, Zhengping

    2016-01-01

    We describe here a one-step method for the synthesis of Au/TiO2 nanosphere materials, which were formed by layered deposition of multiple anatase TiO2 nanosheets. The Au nanoparticles were stabilized by structural defects in each TiO2 nanosheet, including crystal steps and edges, thereby fixing the Au-TiO2 perimeter interface. Reactant transfer occurred along the gaps between these TiO2 nanosheet layers and in contact with catalytically active sites at the Au-TiO2 interface. The doped Au induced the formation of oxygen vacancies in the Au-TiO2 interface. Such vacancies are essential for generating active oxygen species (*O(-)) on the TiO2 surface and Ti(3+) ions in bulk TiO2. These ions can then form Ti(3+)-O(-)-Ti(4+) species, which are known to enhance the catalytic activity of formaldehyde (HCHO) oxidation. These studies on structural and oxygen vacancy defects in Au/TiO2 samples provide a theoretical foundation for the catalytic mechanism of HCHO oxidation on oxide-supported Au materials. Copyright © 2015. Published by Elsevier B.V.

  16. Hydrogen Passivation of Interstitial Zn Defects in Heteroepitaxial InP Cell Structures and Influence on Device Characteristics

    Science.gov (United States)

    Ringel, S. A.; Chatterjee, B.

    2004-01-01

    Hydrogen passivation of heteroepitaxial InP solar cells is of recent interest for deactivation of dislocations and other defects caused by the cell/substrate lattice mismatch that currently limit the photovoltaic performance of these devices. In this paper we present strong evidence that, in addition to direct hydrogen-dislocation interactions, hydrogen forms complexes with the high concentration of interstitial Zn defects present within the p(+) Zn-doped emitter of MOCVD-grown heteroepitaxial InP devices, resulting in a dramatic increase of the forward bias turn-on voltage by as much as 280 mV, from 680 mV to 960 mV. This shift is reproducible and thermally reversible and no such effect is observed for either n(+)p structures or homoepitaxial p(+)n structures grown under identical conditions. A combination of photoluminescence (PL), electrochemical C-V dopant profiling, SIMS and I-V measurements were performed on a set of samples having undergone a matrix of hydrogenation and post-hydrogenation annealing conditions to investigate the source of this voltage enhancement and confirm the expected role of interstitial Zn and hydrogen. A precise correlation between all measurements is demonstrated which indicates that Zn interstitials within the p(+) emitter and their interaction with hydrogen are indeed responsible for this device behavior.

  17. Development of defects in the structure of PIN dosimetry diodes exposed to gamma radiation

    Energy Technology Data Exchange (ETDEWEB)

    Sopko, V. [Hospital Na Bulovce, Department of Radiological Physics, Budinova 2, CZ-18081 Prague 8 (Czech Republic); Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, CZ 12800 Prague 2 (Czech Republic); Sopko, B., E-mail: bruno.sopko@cern.ch [Department of Physics, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technicka 4, CZ 16000 Prague 6 (Czech Republic); Faculty of Production Technology and Management, J. E. Purkyně Univerzity in Ústí nad Labem, Na Okraji 1001, 400 01 Ústí nad Labem (Czech Republic); Chren, D. [Department of Physics, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technicka 4, CZ 16000 Prague 6 (Czech Republic); Dammer, J. [Hospital Na Bulovce, Department of Radiological Physics, Budinova 2, CZ-18081 Prague 8 (Czech Republic); Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, CZ 12800 Prague 2 (Czech Republic); Charles University in Prague, First Faculty of Medicine, Salmovská 1,CZ-12000 Prague 2 (Czech Republic)

    2013-12-01

    Studies of radiation induced defects continue to be relevant as they find an ever greater application due to the increasing radiation doses to which semiconductor detectors are exposed. Efforts of figuring out the changes due to high radiation doses provide the fundamental motivation for this type of experiments. The PIN diode is described, and a developmental disorder caused thereto by 60Co source gamma quanta ranging from 100 kGy to 1 MGy. The calibration curve shows the effect of disturbances on the volt-ampere characteristics as a function of the dose of gamma radiation. The results are compared with earlier published data. Highlights: •We have studied Si PIN diode dosimeters irradiated by gamma. •We measured DLTS spectra and calculated energy traps caused by gamma irradiation. •Increasing dose caused creation of new traps and disappearance of others.

  18. α-Synuclein fibril-induced paradoxical structural and functional defects in hippocampal neurons.

    Science.gov (United States)

    Froula, Jessica M; Henderson, Benjamin W; Gonzalez, Jose Carlos; Vaden, Jada H; Mclean, John W; Wu, Yumei; Banumurthy, Gokulakrishna; Overstreet-Wadiche, Linda; Herskowitz, Jeremy H; Volpicelli-Daley, Laura A

    2018-05-01

    Neuronal inclusions composed of α-synuclein (α-syn) characterize Parkinson's Disease (PD) and Dementia with Lewy bodies (DLB). Cognitive dysfunction defines DLB, and up to 80% of PD patients develop dementia. α-Syn inclusions are abundant in the hippocampus, yet functional consequences are unclear. To determine if pathologic α-syn causes neuronal defects, we induced endogenous α-syn to form inclusions resembling those found in diseased brains by treating hippocampal neurons with α-syn fibrils. At seven days after adding fibrils, α-syn inclusions are abundant in axons, but there is no cell death at this time point, allowing us to assess for potential alterations in neuronal function that are not caused by neuron death. We found that exposure of neurons to fibrils caused a significant reduction in mushroom spine densities, adding to the growing body of literature showing that altered spine morphology is a major pathologic phenotype in synucleinopathies. The reduction in spine densities occurred only in wild type neurons and not in neurons from α-syn knockout mice, suggesting that the changes in spine morphology result from fibril-induced corruption of endogenously expressed α-syn. Paradoxically, reduced postsynaptic spine density was accompanied by increased frequency of miniature excitatory postsynaptic currents (EPSCs) and presynaptic docked vesicles, suggesting enhanced presynaptic function. Action-potential dependent activity was unchanged, suggesting compensatory mechanisms responding to synaptic defects. Although activity at the level of the synapse was unchanged, neurons exposed to α-syn fibrils, showed reduced frequency and amplitudes of spontaneous Ca 2+ transients. These findings open areas of research to determine the mechanisms that alter neuronal function in brain regions critical for cognition at time points before neuron death.

  19. Egyptian pyramid or Aztec pyramid: How should we describe the industrial architecture of automotive supply chains in Europe?

    OpenAIRE

    Vincent FRIGANT (GREThA, CNRS, UMR 5113)

    2011-01-01

    This article questions a terminology that is frequently used to describe automotive supply chains’ industrial architecture. Since vertical disintegration became a trend in the 1980s, this architecture has been represented using the image of the pyramid. Implicitly, authors have had the image of an Egyptian pyramid in mind, one that is pointed at the top and broad at the base. We will demonstrate that even if pyramids are an appropriate image, in the auto industry the Aztec variant, with its s...

  20. Effect of manufacturing method on the magnetic properties and formation of structural defects in Fe61Co10Y8Zr1B20 amorphous alloy

    International Nuclear Information System (INIS)

    Nabialek, M.G.; Pietrusiewicz, P.; Dospial, M.J.; Szota, M.; Błoch, K.; Gruszka, K.; Oźga, K.; Garus, S.

    2014-01-01

    Highlights: • Influence of manufacturing method on structural defects was studied. • Samples were obtained by the use of injection-casting and melt-spinning techniques. • The defects have been indirectly analyzed by approach to ferromagnetic saturation. • Prolonged solidification time allows recombination of atoms arrangement in a volume. • That reduce internal stress and leads to increase in the packing density of atoms. - Abstract: Soft magnetic properties of amorphous alloys are determined by their structure, which strongly depends on their manufacturing method. Alloys obtained in the form of conventional amorphous alloys (tapes) are cooled with a much higher rate than the material obtained in the form of tiles by the injection casting method. The cooling rate and production method determines the type and number of structural defects created in the volume of produced samples. The paper presents an indirect method for the analysis of structural defects and their effect on the magnetic properties of studied alloys. Basing on initial magnetization curve analysis in the area of so-called approach to ferromagnetic saturation was found that point defects were forming in the samples in the form of tapes. The magnetization process of tiles were influenced by the presence of conglomerates of point defects called quasidislocation dipoles

  1. Very high channel conductivity in low-defect AlN/GaN high electron mobility transistor structures

    International Nuclear Information System (INIS)

    Dabiran, A. M.; Wowchak, A. M.; Osinsky, A.; Xie, J.; Hertog, B.; Cui, B.; Chow, P. P.; Look, D. C.

    2008-01-01

    Low defect AlN/GaN high electron mobility transistor (HEMT) structures, with very high values of electron mobility (>1800 cm 2 /V s) and sheet charge density (>3x10 13 cm -2 ), were grown by rf plasma-assisted molecular beam epitaxy (MBE) on sapphire and SiC, resulting in sheet resistivity values down to ∼100 Ω/□ at room temperature. Fabricated 1.2 μm gate devices showed excellent current-voltage characteristics, including a zero gate saturation current density of ∼1.3 A/mm and a peak transconductance of ∼260 mS/mm. Here, an all MBE growth of optimized AlN/GaN HEMT structures plus the results of thin-film characterizations and device measurements are presented

  2. Numerical study of the electronic structure, elastic and optical properties of defect quaternary semiconductor CuGaSnSe4

    Science.gov (United States)

    Shen, Kesheng; Lu, Hai; Zhang, Xianzhou; Jiao, Zhaoyong

    2018-06-01

    The electronic structure, elastic and optical properties of the defect quaternary semiconductor CuGaSnSe4 in I 4 bar structure are systematically investigated using first-principles calculations. We summarize and discuss some of the studies on CuGaSnSe4 in partially ordered chalcopyrite structure and find that there are three atomic arrangements so far, but it is still uncertain which is the most stable. Through detailed simulation and comparison with the corresponding literature, we get three models and predict that M1 model should be the most stable. The band structure and optical properties of compound CuGaSnSe4, including dielectric constant, refractive index and absorption spectrum, are drawn for a more intuitive understanding. The elastic constants are also calculated, which not only prove that CuGaSnSe4 in I 4 bar structure is stable naturally but also help solve the problem of no data to accurately predict axial thermal expansion coefficients. The calculated values of the zero frequency dielectric constant and refractive index are comparable to those of the corresponding chalcopyrite structure but slightly larger.

  3. Subsurface defect detection in first layer of pavement structure and reinforced civil engineering structure by FRP bonding using active infrared thermography

    Science.gov (United States)

    Dumoulin, Jean; Ibos, Laurent

    2010-05-01

    In many countries road network ages while road traffic and maintenance costs increase. Nowadays, thousand and thousand kilometers of roads are each year submitted to surface distress survey. They generally lean on pavement surface imaging measurement techniques, mainly in the visible spectrum, coupled with visual inspection or image processing detection of emergent distresses. Nevertheless, optimisation of maintenance works and costs requires an early detection of defects within the pavement structure when they still are hidden from surface. Accordingly, alternative measurement techniques for pavement monitoring are currently under investigation (seismic methods, step frequency radar). On the other hand, strengthening or retrofitting of reinforced concrete structures by externally bonded Fiber Reinforced Polymer (FRP) systems is now a commonly accepted and widespread technique. However, the use of bonding techniques always implies following rigorous installing procedures. To ensure the durability and long-term performance of the FRP reinforcements, conformance checking through an in situ auscultation of the bonded FRP systems is then highly suitable. The quality-control program should involve a set of adequate inspections and tests. Visual inspection and acoustic sounding (hammer tap) are commonly used to detect delaminations (disbonds) but are unable to provide sufficient information about the depth (in case of multilayered composite) and width of debonded areas. Consequently, rapid and efficient inspection methods are also required. Among the non destructive methods under study, active infrared thermography was investigated both for pavement and civil engineering structures through experiments in laboratory and numerical simulations, because of its ability to be also used on field. Pulse Thermography (PT), Pulse Phase Thermography (PPT) and Principal Component Thermography (PCT) approaches have been tested onto pavement samples and CFRP bonding on concrete

  4. Discovery of a big void in Khufu’s Pyramid by observation of cosmic-ray muons

    Science.gov (United States)

    Morishima, Kunihiro; Kuno, Mitsuaki; Nishio, Akira; Kitagawa, Nobuko; Manabe, Yuta; Moto, Masaki; Takasaki, Fumihiko; Fujii, Hirofumi; Satoh, Kotaro; Kodama, Hideyo; Hayashi, Kohei; Odaka, Shigeru; Procureur, Sébastien; Attié, David; Bouteille, Simon; Calvet, Denis; Filosa, Christopher; Magnier, Patrick; Mandjavidze, Irakli; Riallot, Marc; Marini, Benoit; Gable, Pierre; Date, Yoshikatsu; Sugiura, Makiko; Elshayeb, Yasser; Elnady, Tamer; Ezzy, Mustapha; Guerriero, Emmanuel; Steiger, Vincent; Serikoff, Nicolas; Mouret, Jean-Baptiste; Charlès, Bernard; Helal, Hany; Tayoubi, Mehdi

    2017-12-01

    The Great Pyramid, or Khufu’s Pyramid, was built on the Giza plateau in Egypt during the fourth dynasty by the pharaoh Khufu (Cheops), who reigned from 2509 BC to 2483 BC. Despite being one of the oldest and largest monuments on Earth, there is no consensus about how it was built. To understand its internal structure better, we imaged the pyramid using muons, which are by-products of cosmic rays that are only partially absorbed by stone. The resulting cosmic-ray muon radiography allows us to visualize the known and any unknown voids in the pyramid in a non-invasive way. Here we report the discovery of a large void (with a cross-section similar to that of the Grand Gallery and a minimum length of 30 metres) situated above the Grand Gallery. This constitutes the first major inner structure found in the Great Pyramid since the nineteenth century. The void, named ScanPyramids’ Big Void, was first observed with nuclear emulsion films installed in the Queen’s chamber, then confirmed with scintillator hodoscopes set up in the same chamber and finally re-confirmed with gas detectors outside the pyramid. This large void has therefore been detected with high confidence by three different muon detection technologies and three independent analyses. These results constitute a breakthrough for the understanding of the internal structure of Khufu’s Pyramid. Although there is currently no information about the intended purpose of this void, these findings show how modern particle physics can shed new light on the world’s archaeological heritage.

  5. Influence of ion beam irradiation induced defects on the structural, optical and electrical properties of tellurium nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Narinder [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Department of Physics, Haryana College of Technology & Management, Kaithal, 136027 (India); Kumar, Rajesh [Department of Physics, RN College of Engineering & Technology, Madlauda, 132104 (India); Kumar, Sushil, E-mail: sushil_phys@rediffmail.com [Department of Physics, Chaudhary Devi Lal University, Sirsa, 125055 (India); Chakarvarti, S.K. [Research and Development, Manav Rachana International University, Faridabad, 121001 (India)

    2016-11-01

    In this study, tellurium nanowires were electrodeposited into the polymer membranes from aqueous acidic bath containing HTeO{sub 2}{sup +} ions. The field emission scanning electron microscopy (FESEM) images confirmed the formation of uniform and straight nanowires. The influence of 110 MeV Ni{sup 8+} ion irradiation induced defects on the structural, optical and electrical properties of as–deposited tellurium nanowires were examined using X-ray diffraction (XRD), UV–visible absorption spectroscopy and current–voltage (I–V) measurements. The XRD data depicted the hexagonal phase of tellurium nanowires and further revealed a variation in the intensity of diffraction peaks of ion irradiated nanowires. Williamson–Hall (WH) analysis is used for convoluting the size and microstrain contributions to the width of diffraction peaks. Tellurium nanowires exhibited a distinct absorbance band in the visible region at 686 nm, while this was absent in bulk tellurium. Electrical properties of nanowires are explored on the basis of I–V curves, which revealed a significant increase in the electrical conductivity of irradiated nanowires. A possible mechanism for the enhanced electrical conductivity is the increase in carrier concentration due to thermally excited defects. The defects produced by ion irradiation play a vital role in modifying the properties of semiconducting nanowires. - Highlights: • 110 MeV Ni{sup 8+} ion beam induced changes in tellurium nanowires have been examined. • Nanowires were prepared using template electrodeposition method. • Irradiation improved the electrical conductivity of tellurium nanowires. • Mechanism for enhanced electrical conductivity of irradiated nanowires was discussed.

  6. Influence of Structural Defects on Biomineralized ZnS Nanoparticle Dissolution: An In-Situ Electron Microscopy Study

    Energy Technology Data Exchange (ETDEWEB)

    Eskelsen, Jeremy R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division; Xu, Jie [Univ. of Texas, El Paso, TX (United States). Geological Sciences; Chiu, Michelle Y. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division; Moon, Ji-Won [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Biosciences Division; Wilkins, Branford O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division; Graham, David E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Biosciences Division; Gu, Baohua [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division; Pierce, Eric M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Environmental Sciences Division

    2017-12-19

    The dissolution of metal sulfides, such as ZnS, plays an important role in the fate of metal contaminants in the environment. Here we have examined the dissolution behavior of ZnS nanoparticles synthesized via several abiotic and biological pathways. Specifically, the biogenic ZnS nanoparticles were produced by an anaerobic, metal-reducing bacterium Thermoanaerobacter sp. X513 in a Zn-amended, thiosulfate-containing growth medium, whereas the abiogenic ZnS nanoparticles were produced by mixing an aqueous Zn solution with either H2S-rich gas or Na2S solution. For biogenic synthesis, we prepared two types of samples, in the presence or absence of trace silver (Ag). The size distribution, crystal structure, aggregation behavior, and internal defects of the synthesized ZnS nanoparticles were primarily examined using high-resolution transmission electron microscopy coupled with X-ray energy dispersive spectroscopy. The characterization results show that both the biogenic and abiogenic samples were dominantly composed of sphalerite. In the absence of Ag, the biogenic ZnS nanoparticles were significantly larger (i.e., ~10 nm) than the abiogenic ones (i.e., ~3–5 nm) and contained structural defects (e.g., twins and stacking faults). The presence of trace Ag showed a restraining effect on the particle size of the biogenic ZnS, resulting in quantum-dot-sized nanoparticles (i.e., ~3 nm). In situ dissolution experiments for the synthesized ZnS were conducted with a liquid-cell coupled to a transmission electron microscope (LCTEM), and the primary factors (i.e., the presence or absence structural defects) were evaluated for their effects on the dissolution behavior using the biogenic and abiogenic ZnS nanoparticle samples with the largest average particle size. Analysis of the dissolution results (i.e., change in particle radius with time) using the Kelvin equation shows that the defect-bearing biogenic ZnS nanoparticles (γ = 0.799 J/m2) have

  7. Effect of vanadium doping on structural and magnetic properties of defective nano-nickel ferrite

    Science.gov (United States)

    Heiba, Zein K.; Mohamed, Mohamed Bakr; Wahba, Adel Maher; Almalowi, M. I.

    2018-04-01

    Nano-nickel ferrites defected by vanadium doping (NiV x Fe2-1.67 x O4, 0 ≤ x ≤ 0.25) were prepared using a simple sol gel method. Rietveld analysis revealed a nonmonotonic change in lattice parameter, oxygen parameter and magnetization upon doping with vanadium. Cation distributions suggested from either Rietveld analysis or from experimental magnetic moments were in a good agreement. For low doping values ( x = 0.05), vanadium was residing mainly in octahedral sites, while for samples with vanadium content ( x ≥ 0.1) a significant part of vanadium ions resided at tetrahedral sites; a result which has been confirmed by the analysis of Fourier-transform infrared (FTIR) spectrums obtained for the samples. The transmission electron microscope (TEM) image showed fine spherical particles with size of ˜ 11 nm. All samples showed a superparamagnetic nature with a nonmonotonic change of either magnetization ( M S) or coercivity (H C) with the content of nonmagnetic V5+. The cation occupancies indicated presence of an enormous number of vacancies through doping with high valence cation V5+, making present samples potential electrodes for Li- or Na-ion batteries.

  8. Fabrication of 20.19% Efficient Single-Crystalline Silicon Solar Cell with Inverted Pyramid Microstructure.

    Science.gov (United States)

    Zhang, Chunyang; Chen, Lingzhi; Zhu, Yingjie; Guan, Zisheng

    2018-04-03

    This paper reports inverted pyramid microstructure-based single-crystalline silicon (sc-Si) solar cell with a conversion efficiency up to 20.19% in standard size of 156.75 × 156.75 mm 2 . The inverted pyramid microstructures were fabricated jointly by metal-assisted chemical etching process (MACE) with ultra-low concentration of silver ions and optimized alkaline anisotropic texturing process. And the inverted pyramid sizes were controlled by changing the parameters in both MACE and alkaline anisotropic texturing. Regarding passivation efficiency, the textured sc-Si with normal reflectivity of 9.2% and inverted pyramid size of 1 μm was used to fabricate solar cells. The best batch of solar cells showed a 0.19% higher of conversion efficiency and a 0.22 mA cm -2 improvement in short-circuit current density, and the excellent photoelectric property surpasses that of the same structure solar cell reported before. This technology shows great potential to be an alternative for large-scale production of high efficient sc-Si solar cells in the future.

  9. Structural and elastic properties of defect chalcopyrite HgGa{sub 2}S{sub 4} under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Gomis, O., E-mail: osgohi@fis.upv.es [Centro de Tecnologías Físicas: Acústica, Materiales y Astrofísica, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Santamaría-Pérez, D. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universitat de València, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 València (Spain); Departamento de Química Física I, Universidad Complutense de Madrid, MALTA Consolider Team, Avenida Complutense s/n, 28040 Madrid (Spain); Vilaplana, R.; Luna, R. [Centro de Tecnologías Físicas: Acústica, Materiales y Astrofísica, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Sans, J.A.; Manjón, F.J. [Instituto de Diseño para la Fabricación y Producción Automatizada, MALTA Consolider Team, Universitat Politècnica de València, 46022 València (Spain); Errandonea, D. [Departamento de Física Aplicada-ICMUV, MALTA Consolider Team, Universitat de València, Edificio de Investigación, C/Dr. Moliner 50, Burjassot, 46100 València (Spain); and others

    2014-01-15

    Highlights: • Single crystals of HgGa{sub 2}S{sub 4} with defect-chalcopyrite (DC) structure were synthesized. • High-pressure X-ray diffraction in DC-HgGa{sub 2}S{sub 4} was performed. • Equation of state of DC-HgGa{sub 2}S{sub 4} determined (bulk modulus of 48.4 GPa). • Calculated elastic constants of DC-HgGa{sub 2}S{sub 4} reported at different pressures. • DC-HgGa{sub 2}S{sub 4} becomes mechanically unstable above 13.8 GPa. -- Abstract: In this work, we focus on the study of the structural and elastic properties of mercury digallium sulfide (HgGa{sub 2}S{sub 4}) at high pressures. This compound belongs to the family of AB{sub 2}X{sub 4} ordered-vacancy compounds and exhibits a tetragonal defect chalcopyrite structure. X-ray diffraction measurements at room temperature have been performed under compression up to 15.1 GPa in a diamond anvil cell. Our measurements have been complemented and compared with ab initio total energy calculations. The axial compressibility and the equation of state of the low-pressure phase of HgGa{sub 2}S{sub 4} have been experimentally and theoretically determined and compared to other related ordered-vacancy compounds. The pressure dependence of the theoretical cation–anion and vacancy-anion distances and compressibilities in HgGa{sub 2}S{sub 4} are reported and discussed in comparison to other related ordered-vacancy compounds. Finally, the pressure dependence of the theoretical elastic constants and elastic moduli of HgGa{sub 2}S{sub 4} has been studied. Our calculations indicate that the low-pressure phase of HgGa{sub 2}S{sub 4} becomes mechanically unstable above 13.8 GPa.

  10. Structural Defects of Silver Hollandite, Ag(x)Mn8O(y), Nanorods: Dramatic Impact on Electrochemistry.

    Science.gov (United States)

    Wu, Lijun; Xu, Feng; Zhu, Yimei; Brady, Alexander B; Huang, Jianping; Durham, Jessica L; Dooryhee, Eric; Marschilok, Amy C; Takeuchi, Esther S; Takeuchi, Kenneth J

    2015-08-25

    Hollandites (OMS-2) are an intriguing class of sorbents, catalysts, and energy storage materials with a tunnel structure permitting one-dimensional insertion and deinsertion of ions and small molecules along the c direction. A 7-fold increase in delivered capacity for Li/AgxMn8O16 electrochemical cells (160 versus 23 mAh/g) observed upon a seemingly small change in silver content (x ∼1.1 (L-Ag-OMS-2) and 1.6 (H-Ag-OMS-2)) led us to characterize the structure and defects of the silver hollandite material. Herein, Ag hollandite nanorods are studied through the combined use of local (atomic imaging, electron diffraction, electron energy-loss spectroscopy) and bulk (synchrotron based X-ray diffraction, thermogravimetric analysis) techniques. Selected area diffraction and high resolution transmission electron microscopy show a structure consistent with that refined by XRD; however, the Ag occupancy varies significantly even within neighboring channels. Both local and bulk measurements indicate a greater quantity of oxygen vacancies in L-Ag-OMS-2, resulting in lower average Mn valence relative to H-Ag-OMS-2. Electron energy loss spectroscopy shows a lower Mn oxidation state on the surface relative to the interior of the nanorods, where the average Mn valence is approximately Mn(3.7+) for H-Ag-OMS-2 and Mn(3.5+) for L-Ag-OMS-2 nanorods, respectively. The higher delivered capacity of L-Ag-OMS-2 may be related to more oxygen vacancies compared to H-Ag-OMS-2. Thus, the oxygen vacancies and MnO6 octahedra distortion are assumed to open the MnO6 octahedra walls, facilitating Li diffusion in the ab plane. These results indicate crystallite size and surface defects are significant factors affecting battery performance.

  11. Birth Defects

    Science.gov (United States)

    A birth defect is a problem that happens while a baby is developing in the mother's body. Most birth defects happen during the first 3 months of ... in the United States is born with a birth defect. A birth defect may affect how the ...

  12. Influence of oxygen incorporation on the defect structure of GaN microrods and nanowires. An XPS and CL study

    International Nuclear Information System (INIS)

    Guzmán, G; Herrera, M; Silva, R; Vásquez, G C; Maestre, D

    2016-01-01

    We report a cathodoluminescence (CL) and x-ray photoelectron spectroscopy (XPS) study of the influence of oxygen incorporation on the defect structure of GaN microrods and nanowires. The micro- and nanostructures were synthesized by a thermal evaporation method, which enables us to incorporate oxygen at different concentrations by varying the growth temperature. HR-TEM measurements revealed that oxygen generates stacking fault defects and edge dislocations along the GaN nanowires. Amorphous GaO x N y compounds were segregated on the surface of the nanowires. XPS, XRD and CL measurements suggests that the microrods and nanowires were composed of amorphous oxynitride compounds at their surface and GaN at their inner region. CL measurements revealed that the nanostructures generated an emission of 2.68 eV that increased in intensity proportionally to their oxygen content. We have attributed this emission to electronic transitions between donor substitutional-oxygen (O N ) and acceptor interstitial-oxygen (O i ) state levels. (paper)

  13. Electronic structure of the actinides and their dioxides. Application to the defect formation energy and krypton solubility in uranium dioxide

    International Nuclear Information System (INIS)

    Petit, T.; CEA Centre d'Etudes de Grenoble, 38

    1996-01-01

    Uranium dioxide is the standard nuclear fuel used in French h power plants. During irradiation, fission products such as krypton and xenon are created inside fuel pellets. So, gas release could become, at very high burnup, a limiting factor in the reactor exploitation. To study this subject, we have realised calculations using the Density Functional Theory (DFT) into the Local Density Approximation (LDA) and the Atomic Sphere Approximation (ASA). First, we have validated our approach by calculating cohesive properties of thorium, protactinium and uranium metals. The good agreement between our results and experimental values implies that 5f electrons are itinerant. Calculated lattice parameter, cohesive energy and bulk modulus for uranium and thorium dioxides are in very good agreement with experiment. We show that binding between uranium and oxygen atoms is not completely ionic but partially covalent. The question of the electrical conductivity still remains an open problem. We have been able to calculate punctual defect formation energies in uranium dioxide. Accordingly to experimental observations, we find that it is easier to create a defect in the oxygen sublattice than in the uranium sublattice. Finally, we have been able to predict a probable site of krypton atoms in nuclear fuel: the Schottky trio. Experiences of Extended X-ray Absorption Fine structure Spectroscopy (EXAFS) and X-ray Photoelectron Spectroscopy (XPS) on uranium dioxide doped by ionic implantation will help us in the comprehension of the studied phenomena and the interpretation of our calculations. (author)

  14. Multiresolution, Multi-Scale Target Identification and Tracking using the Anisotropic Diffusion Pyramid

    National Research Council Canada - National Science Library

    Acton, Scott

    1998-01-01

    ...: the anisotropic diffusion pyramid and the morphological pyramid. Coarse-to-fine target searches are implemented within the image pyramids, providing a lOOX improvement in computational expense over standard correlation-based approaches...

  15. Gene pyramiding as a Bt resistance management strategy: How ...

    African Journals Online (AJOL)

    Reports on the emergence of insect resistance to Bacillus thuringiensis delta endotoxins have raised doubts on the sustainability of Bt-toxin based pest management technologies. Corporate industry has responded to this challenge with innovations that include gene pyramiding among others. Pyramiding entails stacking ...

  16. First-principles study of structural, electronic, and optical properties of surface defects in GaAs(001) - β2(2x4)

    Science.gov (United States)

    Bacuyag, Dhonny; Escaño, Mary Clare Sison; David, Melanie; Tani, Masahiko

    2018-06-01

    We performed first-principles calculations based on density functional theory (DFT) to investigate the role of point defects in the structural, electronic, and optical properties of the GaAs(001)- β2(2x4). In terms of structural properties, AsGa is the most stable defect structure, consistent with experiments. With respect to the electronic structure, band structures revealed the existence of sub-band and midgap states for all defects. The induced sub-bands and midgap states originated from the redistributions of charges towards these defects and neighboring atoms. The presence of these point defects introduced deep energy levels characteristic of EB3 (0.97 eV), EL4 (0.52 eV), and EL2 (0.82 eV) for AsGa, GaAs, GaV, respectively. The optical properties are found to be strongly related to these induced gap states. The calculated onset values in the absorption spectra, corresponding to the energy gaps, confirmed the absorption below the known bulk band gap of 1.43 eV. These support the possible two-step photoabsorption mediated by midgap states as observed in experiments.

  17. Wuestite (Fe/1-x/O) - A review of its defect structure and physical properties

    Science.gov (United States)

    Hazen, R. M.; Jeanloz, R.

    1984-01-01

    Such complexities of the Wustite structure as nonstoichiometry, ferric iron variable site distribution, long and short range ordering, and exsolution, yield complex physical properties. Magnesiowustite, a phase which has been suggested to occur in the earth's lower mantle, is also expected to exhibit many of these complexities. Geophysical models including the properties of (Mg, Fe)O should accordingly take into account the uncertainties associated with the synthesis and measurement of iron-rich oxides. Given the variability of the Fe(1-x)O structure, it is important that future researchers define the structural state and extent of exsolution of their samples.

  18. Protonic charge defect structures in floating water bridges observed as Zundel and Eigen solvation arrangements

    Science.gov (United States)

    Teschke, Omar; de Castro, Jose Roberto; Valente Filho, Juracyr Ferraz; Soares, David Mendez

    2017-10-01

    Protonic arrangements were detected in water bridge structures using confocal Raman microscopy, and the spectra show two formed structures. The measured Raman spectra were modified using the voltage applied to the bridge structure, which changed the proportion of these two species. Initially, for a 6.3 kV applied voltage, there was a measurable increase in the bridge current above the Ohmic contribution and the observed Raman spectrum of this new injected specie corresponded to the computed spectrum for the Zundel protonic arrangement. As the voltage further increases a contribution from the Eigen proton solvation specie is added to the measured spectrum.

  19. Crystal structure of tveitite-(Y): Fractionation of rare-earth elements between positions and the variety of defects

    International Nuclear Information System (INIS)

    Yakubovich, O. V.; Massa, W.; Pekov, I. V.; Gavrilenko, P. G.

    2007-01-01

    The crystal structure of the mineral tveitite-(Y) (Y 0.883 Na 0.106 ) (Ca 0.841 LREE 0.159 )(Ca 0.716 Na 0.204 HREE 0.080 )(Ca 0.092 Na 0.074 )F 6.952 from amazonite pegmatites of Rov-Gora Mountain (Keivy, Kola Peninsula) is determined using X-ray diffraction (Stoe IPDS diffractometer, λMoK α , graphite monochromator, 2θ max = 63.5 o , R = 0.051 for 1542 reflections). The main crystal data are as follows: a = 17.020(2) A, c = 9.679(2) A, V = 2428.2(4) A 3 , space group R3-bar, Z = 18, and ρ calcd = 4.00 g/cm 3 . The idealized structural formula of the mineral is represented as (Y,Na) 6 (Ca,LREE) 6 (Ca,Na,HREE) 6 (Ca,Na)F 42 (Z = 3). The defect structure of the mineral manifests itself in a mixed occupation of all four independent cation positions and in a randomly disordered distribution of fluorine atoms over the majority of anion positions. It is shown that the crystal structure of tveitite-(Y) fulfills the function of an 'Eratosthenes sieve' for yttrium cations and two groups of lanthanide cations, so that these cations are distributed over three different positions.

  20. Effects of alloying elements on defect structures in the incubation period for void swelling in austenitic stainless steels

    International Nuclear Information System (INIS)

    Horiki, M.; Yoshiie, T.; Huang, S.S.; Sato, K.; Cao, X.Z.; Xu, Q.; Troev, T.D.

    2013-01-01

    Positron lifetime measurements were used to study the effects of alloying elements on the defect structure during the incubation period for void swelling in several fcc model alloys. Pure Ni, four model alloys (Fe–Cr–Ni, Fe–Cr–Ni–Mo–Mn, Fe–Cr–Ni–Mo–Mn–Si and Fe–Cr–Ni–Mo–Mn–Si–Ti), and four commercial alloys (SUS316LSS, SUS316SS, SUS304SS and Ti added modified SUS316SS) were irradiated with electrons and neutrons. Even at 363 and 573 K to a dose of 0.2 dpa, an effect of alloying elements was observed. At 363 K irradiation, voids were formed only in Ni and Fe–Cr–Ni. At 573 K irradiation, voids were formed in Ni and all model alloys, though the concentration depended on the alloying elements. In commercial alloys, precipitates were formed instead of vacancy clusters, which prevented void growth

  1. Pyramidal approach to license plate segmentation

    Science.gov (United States)

    Postolache, Alexandru; Trecat, Jacques C.

    1996-07-01

    Car identification is a goal in traffic control, transport planning, travel time measurement, managing parking lot traffic and so on. Most car identification algorithms contain a standalone plate segmentation process followed by a plate contents reading. A pyramidal algorithm for license plate segmentation, looking for textured regions, has been developed on a PC based system running Unix. It can be used directly in applications not requiring real time. When input images are relatively small, real-time performance is in fact accomplished by the algorithm. When using large images, porting the algorithm to special digital signal processors can easily lead to preserving real-time performance. Experimental results, for stationary and moving cars in outdoor scenes, showed high accuracy and high scores in detecting the plate. The algorithm also deals with cases where many character strings are present in the image, and not only the one corresponding to the plate. This is done by the means of a constrained texture regions classification.

  2. Liquid crystalline tactoids: ordered structure, defective coalescence and evolution in confined geometries

    Science.gov (United States)

    Wang, Pei-Xi; MacLachlan, Mark J.

    2017-12-01

    Tactoids are liquid crystalline microdroplets that spontaneously nucleate from isotropic dispersions, and transform into macroscopic anisotropic phases. These intermediate structures have been found in a range of molecular, polymeric and colloidal liquid crystals. Typically only studied by polarized optical microscopy, these ordered but easily deformable microdroplets are now emerging as interesting components for structural investigations and developing new materials. In this review, we highlight the structure, property and transformation of tactoids in different compositions, but especially cellulose nanocrystals. We have selected references that illustrate the diversity and most exciting developments in tactoid research, while capturing the historical development of this field. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

  3. Self-assembly of the general membrane-remodeling protein PVAP into sevenfold virus-associated pyramids.

    Science.gov (United States)

    Daum, Bertram; Quax, Tessa E F; Sachse, Martin; Mills, Deryck J; Reimann, Julia; Yildiz, Özkan; Häder, Sabine; Saveanu, Cosmin; Forterre, Patrick; Albers, Sonja-Verena; Kühlbrandt, Werner; Prangishvili, David

    2014-03-11

    Viruses have developed a wide range of strategies to escape from the host cells in which they replicate. For egress some archaeal viruses use a pyramidal structure with sevenfold rotational symmetry. Virus-associated pyramids (VAPs) assemble in the host cell membrane from the virus-encoded protein PVAP and open at the end of the infection cycle. We characterize this unusual supramolecular assembly using a combination of genetic, biochemical, and electron microscopic techniques. By whole-cell electron cryotomography, we monitored morphological changes in virus-infected host cells. Subtomogram averaging reveals the VAP structure. By heterologous expression of PVAP in cells from all three domains of life, we demonstrate that the protein integrates indiscriminately into virtually any biological membrane, where it forms sevenfold pyramids. We identify the protein domains essential for VAP formation in PVAP truncation mutants by their ability to remodel the cell membrane. Self-assembly of PVAP into pyramids requires at least two different, in-plane and out-of-plane, protein interactions. Our findings allow us to propose a model describing how PVAP arranges to form sevenfold pyramids and suggest how this small, robust protein may be used as a general membrane-remodeling system.

  4. Defect structure of cubic solid solutions of alkaline earth and rare earth fluorides

    NARCIS (Netherlands)

    DenHartog, HW

    1996-01-01

    In this paper we will consider the disorder in some cubic solid solutions consisting of one of the alkaline earth fluorides and one of the rare earth fluorides. This is an attractive group of model materials, because these materials have a rather simple overall cubic structure. We will discuss the

  5. PROGRESS ON DEVELOPING SONIC INFRARED IMAGING FOR DEFECT DETECTION IN COMPOSITE STRUCTURES

    International Nuclear Information System (INIS)

    Han Xiaoyan; He Qi; Li Wei; Newaz, Golam; Favro, Lawrence D.; Thomas, Robert L.

    2010-01-01

    At last year's QNDE conference, we presented our development of Sonic IR imaging technology in metal structures, with results from both experimental studies and theoretical computing. In the latest aircraft designs, such as the B787 from Boeing, composites have become the major materials in structures such as the fuselage and wings. This is in contrast to composites' use only in auxiliary components such as flaps and spoilers in the past. With today's advanced technology of fabrication, it is expected the new materials can be put in use in even more aircraft structures due to its light weight and high strength (high strength-to-weight ratio), high specific stiffness, tailorability of properties, design flexibility etc. Especially, with increases in fuel cost, reducing the aircraft's body weight becomes more and more appealing. In this presentation, we describe the progress on our development of Sonic IR imaging for aircraft composite structures. In particular, we describe the some unexpected results discovered while modeling delaminations. These results were later experimentally verified with an engineered delamination.

  6. C8-structured carbon quantum dots: Synthesis, blue and green double luminescence, and origins of surface defects

    Science.gov (United States)

    Xifang, Chen; Wenxia, Zhang; Qianjin, Wang; Jiyang, Fan

    Carbon quantum dots (CQDs) have attracted great attention in the past few years due to their low cytotoxicity, exploited various synthesis methods, unexampled abundance of raw materials on earth, and robust near-infrared to near-UV luminescence. Carbon nanoparticles have applications in biological labeling, delivery of drugs and biological molecules into cells, and light emitting diodes and lasing. CQDs generally exist as nanodiamonds or graphite quantum dots according to previous research reports. In this study, we report the first synthesis of the third-allotrope CQDs through carbonization of sucrose and study their luminescence properties. These CQDs have a body-centered cubic structure and each lattice point is composed of eight atoms which form a sub-cube (so called C8 crystal structure). High-resolution transmission electron microscopy and X-ray diffraction confirm the C8 structure of the synthesized carbon nanocrystallites with an average size of 2 nm. The C8 CQDs exhibit double-band luminescence with two peaks centered at around 432 and 520 nm. The study based on the photoluminescence, UV-Vis absorption, Fourier-transform infrared, and X-ray photoelectron spectroscopies reveals that the green emission originates from the C=O related surface defect.

  7. Structural analysis of Herbaspirillum seropedicae lipid-A and of two mutants defective to colonize maize roots.

    Science.gov (United States)

    Serrato, Rodrigo V; Balsanelli, Eduardo; Sassaki, Guilherme L; Carlson, Russell W; Muszynski, Artur; Monteiro, Rose A; Pedrosa, Fábio O; Souza, Emanuel M; Iacomini, Marcello

    2012-11-01

    Lipid-A was isolated by mild acid hydrolysis from lipopolysaccharides extracted from cells of Herbaspirillum seropedicae, strain SMR1, and from two mutants deficient in the biosynthesis of rhamnose (rmlB⁻ and rmlC⁻). Structural analyzes were carried out using MALDI-TOF and derivatization by per-O-trimethylsilylation followed by GC-MS in order to determine monosaccharide and fatty acid composition. De-O-acylation was also performed to determine the presence of N-linked fatty acids. Lipid-A from H. seropedicae SMR1 showed a major structure comprising 2-amino-2-deoxy-glucopyranose-(1→6)-2-amino-2-deoxy-glucopyranose phosphorylated at C4' and C1 positions, each carrying a unit of 4-amino-4-deoxy-arabinose. C2 and C2' positions were substituted by amide-linked 3-hydroxy-dodecanoic acids. Both rhamnose-defective mutants showed similar structure for their lipid-A moieties, except for the lack of 4-amino-4-deoxy-arabinose units attached to phosphoryl groups. Copyright © 2012 Elsevier B.V. All rights reserved.

  8. First-principles study of native defects in bulk Sm2CuO4 and its (001) surface structure

    Science.gov (United States)

    Zheng, Fubao; Zhang, Qinfang; Meng, Qiangqiang; Wang, Baolin; Song, Fengqi; Yunoki, Seiji; Wang, Guanghou

    2018-04-01

    Using the first-principles calculations based on the density functional theory, we have studied the bulk defect formation and surface structures of Sm2CuO4. To ensure the accuracy of calculations, the spin order of Cu atoms is rechecked and it is the well-known nearest-neighbor antiferromagnetic ground state, which can be attributed to the hole-mediated superexchange through the strong pdσ hybridization interaction between Cu dx2-y2 electron and the neighboring oxygen px (or py) electron. Under each present experimental condition, the Sm vacancy has a very high formation energy and is unlikely to be stable. The Cu vacancy is a shallow acceptor, which is preferred under O-rich conditions, whereas the O vacancy is a donor and energetically favorable under O-poor conditions. To construct its (001) surface structure, CuOO, CuO, and Cu terminated surfaces are found to be most favorable under different experimental conditions. The stable surface structures are always accompanied by significant surface atomic reconstructions and electron charge redistribution, which are intimately correlated to each other.

  9. Prickle1 mutation causes planar cell polarity and directional cell migration defects associated with cardiac outflow tract anomalies and other structural birth defects

    Directory of Open Access Journals (Sweden)

    Brian C. Gibbs

    2016-03-01

    Full Text Available Planar cell polarity (PCP is controlled by a conserved pathway that regulates directional cell behavior. Here, we show that mutant mice harboring a newly described mutation termed Beetlejuice (Bj in Prickle1 (Pk1, a PCP component, exhibit developmental phenotypes involving cell polarity defects, including skeletal, cochlear and congenital cardiac anomalies. Bj mutants die neonatally with cardiac outflow tract (OFT malalignment. This is associated with OFT shortening due to loss of polarized cell orientation and failure of second heart field cell intercalation mediating OFT lengthening. OFT myocardialization was disrupted with cardiomyocytes failing to align with the direction of cell invasion into the outflow cushions. The expression of genes mediating Wnt signaling was altered. Also noted were shortened but widened bile ducts and disruption in canonical Wnt signaling. Using an in vitro wound closure assay, we showed Bj mutant fibroblasts cannot establish polarized cell morphology or engage in directional cell migration, and their actin cytoskeleton failed to align with the direction of wound closure. Unexpectedly, Pk1 mutants exhibited primary and motile cilia defects. Given Bj mutant phenotypes are reminiscent of ciliopathies, these findings suggest Pk1 may also regulate ciliogenesis. Together these findings show Pk1 plays an essential role in regulating cell polarity and directional cell migration during development.

  10. Effect of steel structure and defects on reliability of parts of impact mechanisms

    Science.gov (United States)

    Popelyukh, AI; Repin, AA; Alekseev, SE

    2018-03-01

    The paper discusses selection of materials suitable for manufacturing critical parts of impact mechanisms. It is shown that in order to extend life of parts exposed to high dynamic loading, it is expedient to use medium- and high-carbon alloy-treated steels featuring low impurity with nonmetallic inclusions and high hardening characteristics. Application of thermally untreated parts is undesirable as steel having ferrite–pearlite structure possesses low fatigue strength. Aimed to ensure high reliability of parts with a hardness of 42–55 HRC, steel should be reinforced by thermal treatement with the formation of multicomponent martensite–bainite structure. High-quality production should include defectoscopy and incoming material control.

  11. Evaluation of the effect of corrosion defects on the structural integrity of X52 gas pipelines using the SINTAP procedure and notch theory

    International Nuclear Information System (INIS)

    Adib, H.; Jallouf, S.; Schmitt, C.; Carmasol, A.; Pluvinage, G.

    2007-01-01

    The notch stress intensity factor concept and the structural integrity assessment procedure for European industry (SINTAP) structural integrity procedure are used to assess gas pipeline integrity using deterministic and probabilistic methods. These pipes have external longitudinal semi-elliptical corrosion defects. Stress concentration at a defect tip is investigated via elastic-plastic finite element method analysis. The notch stress intensity concept is implemented into the SINTAP procedure and a notch-based failure assessment diagram is proposed. The safety factor and security factor are calculated through the SINTAP basic level

  12. Evaluation of the effect of corrosion defects on the structural integrity of X52 gas pipelines using the SINTAP procedure and notch theory

    Energy Technology Data Exchange (ETDEWEB)

    Adib, H. [ENIM, Laboratoire de Fiabilite Mecanique (LFM) Ile du Saulcy, 57045 Metz Cedex (France); Jallouf, S. [ENIM, Laboratoire de Fiabilite Mecanique (LFM) Ile du Saulcy, 57045 Metz Cedex (France); Schmitt, C. [ENIM, Laboratoire de Fiabilite Mecanique (LFM) Ile du Saulcy, 57045 Metz Cedex (France)]. E-mail: schmitt@enim.fr; Carmasol, A. [ENIM, Laboratoire de Fiabilite Mecanique (LFM) Ile du Saulcy, 57045 Metz Cedex (France); Pluvinage, G. [ENIM, Laboratoire de Fiabilite Mecanique (LFM) Ile du Saulcy, 57045 Metz Cedex (France)

    2007-03-15

    The notch stress intensity factor concept and the structural integrity assessment procedure for European industry (SINTAP) structural integrity procedure are used to assess gas pipeline integrity using deterministic and probabilistic methods. These pipes have external longitudinal semi-elliptical corrosion defects. Stress concentration at a defect tip is investigated via elastic-plastic finite element method analysis. The notch stress intensity concept is implemented into the SINTAP procedure and a notch-based failure assessment diagram is proposed. The safety factor and security factor are calculated through the SINTAP basic level.

  13. Fundamental Study of Micro-Defects in Electropolished EB-Welded and Hydroformed SRF Accelerating Structures

    Energy Technology Data Exchange (ETDEWEB)

    Sumption, Mike

    2014-08-29

    In the area of niobium elecropolishing fundamentals, we focused on understanding the influence of the surface topology, and geometry (with effects from gravity included. The formation of a viscous film is essential for the electropolishing process to take place. The exact nature and composition of the film formed on niobium is still unknown because of its solubility in the electrolyte. Extensive pitting may take place at surface where a stable film cannot form. This has to be taken into consideration while determining the speed with which the SRF cavities are rotated while EP. Hydrodynamic aspects must be taken into consideration while optimizing the polishing parameters. There is improvement in surface finish with polishing time. There is a huge change in surface quality when the EP time is increased from 2 hours to 4 hours but not much change takes place when the time is further increased to 6 hours. So keeping the economic points in view, about 100 um defect layer removal may be sufficient to get the desired performance. In the area of Electropolishing of untreated and treated niobium with Weld Joints we studied untreated and treated Nb, especially for the heat affected areas next to welded bumps, electropolished for different durations. The electropolishing of the untreated Nb caused the formation of pits on the surface at about 15 min but they disappeared when the electropolishing duration was more than 15 min. Electropolishing for 120 min smoothened the surface of untreated Nb by levelling the surface, but the severe formation of pits on the whole surface was found after 240 min. The treatment of Nb significantly changed the Nb surface morphology which was covered by grains of different size that looked light or dark in the optical microscope. The treated Nb was susceptible to pitting during the entire electropolishing starting from 15 min and the dark grains had more susceptibility to pitting than the light grains. In addition, electropolishing for 240 min

  14. Study of the defect structure of ''pure'' and doped nonstoichiometric CeO2. Final report, January 1, 1965--May 31, 1977

    International Nuclear Information System (INIS)

    Blumenthal, R.N.

    1977-11-01

    The defect structure and transport properties of defects in nonstoichiometric oxides was studied based on their electrical and thermodynamic behavior. Similar studies were also made on doped-nonstoichiometric oxides to determine the effect of the ionic radii, valence and concentration of the dopant cation on the nonstoichiometric defect structure and the transport properties of these defects. The thermodynamic and electrical property study on ''pure'' and doped-nonstoichiometric CeO 2 /sub -x/ is reviewed. The combined study of the electrical conductivity, ionic transference, and thermodynamic measurements initiated on CaO-doped CeO 2 as a function of temperature, oxygen pressure and CaO content is discussed. The results of similar measurements on CeO 2 doped with other oxides (e.g., ThO 2 , Ta 2 O 5 , etc.) which have cations with different valences and ionic radii are also discussed. The primary objective of these studies was to determine the effect of ionic radii, valence and concentration of the dopant cation on (1) the nonstoichiometric behavior, (2) the thermodynamic quantities ΔantiH/sub O 2 / and ΔantiS/sub O 2 /, (3) the nonstoichiometric defect structure, (4) the electronic and ionic conductivities, and (5) the mobility of electrons and oxygen vacancies in doped CeO 2 /sub -x/

  15. Structural characterization of GaAs self-assembled quantum dots grown by Droplet Epitaxy on Ge virtual substrates on Si

    International Nuclear Information System (INIS)

    Frigeri, C.; Bietti, S.; Isella, G.; Sanguinetti, S.

    2013-01-01

    The structure of self-assembled quantum dots (QDs) grown by Droplet Epitaxy on Ge virtual substrates has been investigated by TEM. The QDs have a pyramidal shape with base and height of 50 nm. By (0 0 2) dark field TEM it was seen that the pyramid top is Ga poor and Al rich most likely because of the higher mobility of Ga along the pyramid sides down to the base. The investigated QDs contain defects identified as As precipitates by Moirè fringes. The smallest ones (3–5 nm) are coherent with the GaAs lattice suggesting that they could be a cubic phase of As precipitation. It seems to be a metastable phase since the hexagonal phase is recovered as the precipitate size increases above ∼5 nm.

  16. Relevance of the pyramidal syndrome in amyotrophic lateral sclerosis.

    Science.gov (United States)

    Álvarez, N; Díez, L; Avellaneda, C; Serra, M; Rubio, M Á

    Pyramidal signs (hyperreflexia, spasticity, Babinski sign) are essential for the diagnosis of amyotrophic lateral sclerosis (ALS). However, these signs are not always present at onset and may vary over time, besides which their role in disease evolution is controversial. Our goal was to describe which pyramidal signs were present and how they evolved in a cohort of patients with ALS, as well as their role in prognosis. Retrospective analysis of prospectively collected patients diagnosed with ALS in our centre from 1990 to 2015. Of a total of 130 patients with ALS, 34 (26.1%) patients showed no pyramidal signs at the first visit while 15 (11.5%) had a complete pyramidal syndrome. Of those patients without initial pyramidal signs, mean time of appearance of the first signs was 4.5 months. Babinski sign was positive in 64 (49.2%) patients, hyperreflexia in 90 (69.2%) and 22 (16.9%) patients had spasticity. Pyramidal signs tended to remain unchanged over time, although they seem to appear at later stages or even disappear with time in some patients. We found no association between survival and the presence of changes to pyramidal signs, although decreased spasticity was associated with greater clinical deterioration (ALSFR scale) (P<.001). A quarter of patients with ALS initially showed no pyramidal signs and in some cases they even disappear over time. These data support the need for tools that assess the pyramidal tract. Copyright © 2016 Sociedad Española de Neurología. Publicado por Elsevier España, S.L.U. All rights reserved.

  17. Structural and electronic properties of the adsorbed and defected Cu nanowires: A density-functional theory study

    Energy Technology Data Exchange (ETDEWEB)

    Duan, Ying-Ni [College of Physics and Information Technology, Shaanxi Normal University, Xian 710062, Shaanxi (China); Department of Medical Engineering and Technology, Xinjiang Medical University, Urumqi 830011, Xinjiang (China); Zhang, Jian-Min, E-mail: jianm_zhang@yahoo.com [College of Physics and Information Technology, Shaanxi Normal University, Xian 710062, Shaanxi (China); Fan, Xiao-Xi [Department of Medical Engineering and Technology, Xinjiang Medical University, Urumqi 830011, Xinjiang (China); Xu, Ke-Wei [College of Physics and Mechanical and Electronic Engineering, Xian University of Arts and Science, Xian 710065, Shaanxi (China)

    2014-12-01

    Using first-principles calculations based on density-functional theory, we systematically investigate the influence of adsorbates (CO molecule and O atom) and defects (adsorb one extra Cu atom and monovacancy) on the structural and electronic properties of Cu{sub 5-1}NW and Cu{sub 6-1}NW. For both nanowires, CO molecule prefers to adsorb on the top site, while O atom prefers to adsorb on the center site. The hybridization between the CO and Cu states is dominated by the donation–backdonation process, which leads to the formation of bonding/antibonding pairs, 5σ{sub b}/5σ{sub a} and 2π{sub b}{sup ⁎}/2π{sub a}{sup ⁎}. The larger adsorption energies, larger charge transfers to O adatom and larger decrease in quantum conductance 3G{sub 0} for an O atom adsorbed on the Cu{sub 5-1}NW and Cu{sub 6-1}NW show both Cu{sub 5-1}NW and Cu{sub 6-1}NW can be used as an O sensor. Furthermore, the decrease in quantum conductance 1G{sub 0} for a CO molecule adsorbed on the Cu{sub 6-1}NW also shows the Cu{sub 6-1}NW can be used to detect CO molecule. So we expect these results may have implications for CuNW based chemical sensing. High adsorption energy of one extra Cu atom and relatively low formation energy of a monovacancy suggest that these two types of defects are likely to occur in the fabrication of CuNWs. One extra Cu atom does not decrease the quantum conductance, while a Cu monovacancy leads to a drop of the quantum conductance.

  18. Role of oxygen and structural defects in properties of high-Tc superconductors

    International Nuclear Information System (INIS)

    Raveau, B.; Michel, C.; Hervieu, M.; Deslandes, F.; Maignan, A.

    1989-01-01

    Almost two years have passed since the discovery of superconductivity in mixed-valence copper oxides. A number of papers have now been published in this field. In spite of these numerous results, the mechanisms which govern superconductivity in those oxides are so far not understood. The authors discuss how the study of the crystal chemistry of these oxides suggests that two points are of capital importance for the appearance of superconductivity in those compounds: the low dimensionality of the structure and the mixed-valence of copper

  19. Multilevel probabilistic approach to evaluate manufacturing defect in composite aircraft structures

    International Nuclear Information System (INIS)

    Caracciolo, Paola

    2014-01-01

    In this work it is developed a reliable approach and its feasibility to the design and analysis of a composite structures. The metric is compared the robustness and reliability designs versus the traditional design, to demonstrate the gain that can be achieved with a probabilistic approach. The use of the stochastic approach of the uncertain parameteters in combination with the multi-scale levels analysis is the main objective of this paper. The work is dedicated to analyze the uncertainties in the design, tests, manufacturing process, and key gates such as materials characteristic

  20. Multilevel probabilistic approach to evaluate manufacturing defect in composite aircraft structures

    Energy Technology Data Exchange (ETDEWEB)

    Caracciolo, Paola, E-mail: paola.caracciolo@airbus.com [AIRBUS INDUSTRIES Germany, Department of Airframe Architecture and Integration-Research and Technology-Kreetslag, 10, D-21129, Hamburg (Germany)

    2014-05-15

    In this work it is developed a reliable approach and its feasibility to the design and analysis of a composite structures. The metric is compared the robustness and reliability designs versus the traditional design, to demonstrate the gain that can be achieved with a probabilistic approach. The use of the stochastic approach of the uncertain parameteters in combination with the multi-scale levels analysis is the main objective of this paper. The work is dedicated to analyze the uncertainties in the design, tests, manufacturing process, and key gates such as materials characteristic.

  1. Detection and sizing of defects in structural components of a nuclear power plant by ECT

    International Nuclear Information System (INIS)

    Chen, Z.; Miya, K.

    2004-01-01

    In this paper, progress of ECT (eddy current testing) technique for inspection of stress corrosion cracks in a structural component of a nuclear power plant is reported. Access and scanning vehicle (robot), advanced probes for steam generator tube inspection, development and evaluation of new probes for welding joint, and ECT based crack sizing technique are described respectively. Based on these new techniques, it is clarified that ECT can play as a supplement of ultrasonic techniques for the welding zone inspection. It is also proved in this work that new ECT sensors are efficient even for a stainless plate as thick as 15 mm. (authors)

  2. Detection and Sizing of Defects in Structural Components of a Nuclear Power Plant by ECT

    International Nuclear Information System (INIS)

    Chen Zhenmao; Miya, Kenzo

    2005-01-01

    In this paper, progress of ECT technique for inspection of stress corrosion cracks in a structural component of a nuclear power plant is reported. Access and scanning vehicle (robot), advanced probes for SG tube inspection, development and evaluation of new probes for welding joint, and ECT based crack sizing technique are described respectively. Based on these new techniques, it is clarified that ECT can play as a supplement of UT for the welding zone inspection. It is also proved in this work that new ECT sensors are efficient even for a stainless plate as thick as 15mm

  3. Electronic structure and optical properties of defect chalcopyrite HgGa2Se4

    Science.gov (United States)

    Gabrelian, B. V.; Lavrentyev, A. A.; Vu, Tuan V.; Parasyuk, O. V.; Khyzhun, O. Y.

    2018-01-01

    We report on studies from an experimental and theoretical viewpoint of the electronic structure of mercury digallium selenide, HgGa2Se4, a very promising optoelectronic material. In particular, the method of X-ray photoelectron spectroscopy (XPS) was used to evaluate binding energies of the constituent element core electrons and the shape of the valence band for pristine and Ar+-ion bombarded surfaces of HgGa2Se4 single crystal. First principles band-structure calculations were performed in the present work using the augmented plane wave + local orbitals (APW+lo). These calculations indicate that the Se 4p states are the main contributors at the top and in the upper portion of the valence band with slightly smaller contributions of the Ga 4p states in the upper portion of the band as well. Further, the central portion of the valence band is determined mainly by contributions of the Ga 4s states, and the Hg 5d states are the principal contributors to the bottom of the valence band. These theoretical data are in fair agreement when matching on a common energy scale of the X-ray emission bands giving information on the energy distribution of the Se 4p and Ga 4p states and the XPS valence-band spectrum of the HgGa2Se4 crystal. The principal optical constants are elucidated from the DFT calculations.

  4. Ultra-structural defects cause low bone matrix stiffness despite high mineralization in osteogenesis imperfecta mice.

    Science.gov (United States)

    Vanleene, Maximilien; Porter, Alexandra; Guillot, Pascale-Valerie; Boyde, Alan; Oyen, Michelle; Shefelbine, Sandra

    2012-06-01

    Bone is a complex material with a hierarchical multi-scale organization from the molecule to the organ scale. The genetic bone disease, osteogenesis imperfecta, is primarily caused by mutations in the collagen type I genes, resulting in bone fragility. Because the basis of the disease is molecular with ramifications at the whole bone level, it provides a platform for investigating the relationship between structure, composition, and mechanics throughout the hierarchy. Prior studies have individually shown that OI leads to: 1. increased bone mineralization, 2. decreased elastic modulus, and 3. smaller apatite crystal size. However, these have not been studied together and the mechanism for how mineral structure influences tissue mechanics has not been identified. This lack of understanding inhibits the development of more accurate models and therapies. To address this research gap, we used a mouse model of the disease (oim) to measure these outcomes together in order to propose an underlying mechanism for the changes in properties. Our main finding was that despite increased mineralization, oim bones have lower stiffness that may result from the poorly organized mineral matrix with significantly smaller, highly packed and disoriented apatite crystals. Using a composite framework, we interpret the lower oim bone matrix elasticity observed as the result of a change in the aspect ratio of apatite crystals and a disruption of the crystal connectivity. Copyright © 2012 Elsevier Inc. All rights reserved.

  5. Ischemic stroke of the pyramidal decussation causing quadriplegia and anarthria.

    Science.gov (United States)

    Wilkins, Emilia G; Kamel, Hooman; Johnson, Eric C B; Shalev, Sarah M; Josephson, S Andrew

    2012-10-01

    A 52-year-old man with a history of hypertension and previously irradiated head and neck cancer presented with quadriplegia and anarthria sparing the face and sensory functions. Brain magnetic resonance imaging (MRI) demonstrated acute infarction of the pyramidal decussation. We describe the clinical and radiological characteristics of infarction at the pyramidal decussation and review the arterial supply to this region in the lower brainstem. Although rare, infarction of the pyramidal decussation should be considered in the differential diagnosis when patients present with atraumatic pure motor quadriplegia. Copyright © 2012 National Stroke Association. Published by Elsevier Inc. All rights reserved.

  6. Inclinations of Egyptian pyramids and finding of the divine essence

    OpenAIRE

    GRIGORIEV STANISLAV ARKADIEVICH

    2015-01-01

    The aim of this research is discovery of astronomical reasons in orientation of slopes of Egyptian pyramids used as tombs for pharaohs of Ancient Egypt. The article contains results of statistical analysis of change in inclination of slopes of the pyramids (3rd 2nd millennia BC) depending on time of their building. The first year of the corresponding pharaoh’s reign has been accepted, as usually it is considered that building of pyramids ones started during either the first or second year of ...

  7. Defect-property correlations in garnet crystals. III. The electrical conductivity and defect structure of luminescent nickel-doped yttrium aluminum garnet

    International Nuclear Information System (INIS)

    Rotman, S.R.; Tuller, H.L.

    1987-01-01

    The conduction mechanisms in nickel-doped yttrium aluminum garnet (Ni:YAG) have been studied as a function of temperature and partial pressue of oxygen. ac conductivity and ionic transference measurements show that Ni:YAG is a mixed ionic-electronic conductor with an ionic mobility characterized by an activation energy of 2.0--2.2 eV. The reduction of Ni +3 to Ni +2 causes an increase in the oxygen vacancy concentration and a concurrent rise in the magnitude of the ionic conductivity. Codoping with zirconium, on the other hand, fixes the nickel in the divalent state, increases the n-type conductivity, and lowers the degree of ionic conductivity. A defect model is presented which is consistent with all of these observations

  8. Evaluating the performance of graphene with structural defect and functionalized by –C6H4 as an electrode active material for supercapacitors

    Directory of Open Access Journals (Sweden)

    S M Mousavi-Khoshdel

    2017-02-01

    Full Text Available In this study, quantum capacitance of graphene-based electrodes is evaluated using Density Functional Theory (DFT calculations. The obtained results showed that quantum capacitance of graphene-based supercapacitors could be significantly improved by existence of structural defects on the graphene sheets at sufficiently high concentrations because of creating impure states resulted from carbon pz orbitals involved in defect. In another section of calculations, quantum capacitance of functionalized graphene with –C6H4, is evaluated. The obtained results of calculations showed that functionalized graphene with this functional group have a very good capacitance in comparison with pristine graphene, especially at smaller voltages of less than -1.0 V or greater than 1.0 V. Hybrid configurations between structural defects and functional group of –C6H4 was also studied. In general, the results indicated that the combined configuration shows higher capacity than pristine graphene

  9. Defect modelling

    International Nuclear Information System (INIS)

    Norgett, M.J.

    1980-01-01

    Calculations, drawing principally on developments at AERE Harwell, of the relaxation about lattice defects are reviewed with emphasis on the techniques required for such calculations. The principles of defect modelling are outlined and various programs developed for defect simulations are discussed. Particular calculations for metals, ionic crystals and oxides, are considered. (UK)

  10. Defect formation in oxygen- and boron- implanted MOS structures after gamma irradiation

    CERN Document Server

    Kaschieva, S; Skorupa, W

    2003-01-01

    The effect of gamma irradiation on the interface states of ion-implanted MOS structures is studied by means of the thermally stimulated charge method. 10-keV oxygen- or boron- (O sup + or B sup +) implanted samples are gamma-irradiated with sup 6 sup 0 Co. Gamma irradiation creates electron levels at the SiSiO sub 2 interface of the samples in a different way depending on the type of the previously implanted atoms (O sup + or B sup +). The results demonstrate that the concentration of the shallower levels (in the silicon band gap) of oxygen-implanted samples increases more effectively after gamma irradiation. The same irradiation conditions increase more intensively the concentration of the deeper levels (in the silicon band gap) of boron-implanted samples. (orig.)

  11. An improved potential drop method for measuring and monitoring defects in metallic structures

    International Nuclear Information System (INIS)

    Oppermann, W.; Keller, H.P.

    1993-01-01

    In the developed form described the direct current potential drop method is a reliable and relatively accurate procedure for the measuring and surveillance of surface cracks in metallic materials. There are also significant possibilities in practice of surveying cracks on the inaccessible side of the structure. The basis for the improvement in accuracy, in particular for short cracks, is firstly an improved measuring technique and secondly calibration curves determined using an electrolytic tank. Practical experience gained in conventional plants is to date positive. The opportunity exists of benefitting from the advantages that would be brought about by an increased use of the potential drop method in plant surveillance. In nuclear plants specifically this would achieve a reduction in the testing personnel's exposure to radiation. (orig.)

  12. Structure of a PKA RIα Recurrent Acrodysostosis Mutant Explains Defective cAMP-Dependent Activation.

    Science.gov (United States)

    Bruystens, Jessica Gh; Wu, Jian; Fortezzo, Audrey; Del Rio, Jason; Nielsen, Cole; Blumenthal, Donald K; Rock, Ruth; Stefan, Eduard; Taylor, Susan S

    2016-12-04

    Most disease-related mutations that impair cAMP protein kinase A (PKA) signaling are present within the regulatory (R) PKA RI alpha-subunit (RIα). Although mutations in the PRKAR1A gene are linked to Carney complex (CNC) disease and, more recently, to acrodysostosis-1 (ACRDYS1), the two diseases show contrasting phenotypes. While CNC mutations cause increased PKA activity, ACRDYS1 mutations result in decreased PKA activity and cAMP resistant holoenzymes. Mapping the ACRDYS1 disease mutations reveals their localization to the second of two tandem cAMP-binding (CNB) domains (CNB-B), and here, we characterize a recurrent deletion mutant where the last 14 residues are missing. The crystal structure of a monomeric form of this mutant (RIα92-365) bound to the catalytic (C)-subunit reveals the dysfunctional regions of the RIα subunit. Beyond the missing residues, the entire capping motif is disordered (residues 357-379) and explains the disrupted cAMP binding. Moreover, the effects of the mutation extend far beyond the CNB-B domain and include the active site and N-lobe of the C-subunit, which is in a partially open conformation with the C-tail disordered. A key residue that contributes to this crosstalk, D267, is altered in our structure, and we confirmed its functional importance by mutagenesis. In particular, the D267 interaction with Arg241, a residue shown earlier to be important for allosteric regulation, is disrupted, thereby strengthening the interaction of D267 with the C-subunit residue Arg194 at the R:C interface. We see here how the switch between active (cAMP-bound) and inactive (holoenzyme) conformations is perturbed and how the dynamically controlled crosstalk between the helical domains of the two CNB domains is necessary for the functional regulation of PKA activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Development of inhibitory synaptic inputs on layer 2/3 pyramidal neurons in the rat medial prefrontal cortex

    KAUST Repository

    Virtanen, Mari A.; Lacoh, Claudia Marvine; Fiumelli, Hubert; Kosel, Markus; Tyagarajan, Shiva; de Roo, Mathias; Vutskits, Laszlo

    2018-01-01

    Inhibitory control of pyramidal neurons plays a major role in governing the excitability in the brain. While spatial mapping of inhibitory inputs onto pyramidal neurons would provide important structural data on neuronal signaling, studying their distribution at the single cell level is difficult due to the lack of easily identifiable anatomical proxies. Here, we describe an approach where in utero electroporation of a plasmid encoding for fluorescently tagged gephyrin into the precursors of pyramidal cells along with ionotophoretic injection of Lucifer Yellow can reliably and specifically detect GABAergic synapses on the dendritic arbour of single pyramidal neurons. Using this technique and focusing on the basal dendritic arbour of layer 2/3 pyramidal cells of the medial prefrontal cortex, we demonstrate an intense development of GABAergic inputs onto these cells between postnatal days 10 and 20. While the spatial distribution of gephyrin clusters was not affected by the distance from the cell body at postnatal day 10, we found that distal dendritic segments appeared to have a higher gephyrin density at later developmental stages. We also show a transient increase around postnatal day 20 in the percentage of spines that are carrying a gephyrin cluster, indicative of innervation by a GABAergic terminal. Since the precise spatial arrangement of synaptic inputs is an important determinant of neuronal responses, we believe that the method described in this work may allow a better understanding of how inhibition settles together with excitation, and serve as basics for further modelling studies focusing on the geometry of dendritic inhibition during development.

  14. Development of inhibitory synaptic inputs on layer 2/3 pyramidal neurons in the rat medial prefrontal cortex

    KAUST Repository

    Virtanen, Mari A.

    2018-01-10

    Inhibitory control of pyramidal neurons plays a major role in governing the excitability in the brain. While spatial mapping of inhibitory inputs onto pyramidal neurons would provide important structural data on neuronal signaling, studying their distribution at the single cell level is difficult due to the lack of easily identifiable anatomical proxies. Here, we describe an approach where in utero electroporation of a plasmid encoding for fluorescently tagged gephyrin into the precursors of pyramidal cells along with ionotophoretic injection of Lucifer Yellow can reliably and specifically detect GABAergic synapses on the dendritic arbour of single pyramidal neurons. Using this technique and focusing on the basal dendritic arbour of layer 2/3 pyramidal cells of the medial prefrontal cortex, we demonstrate an intense development of GABAergic inputs onto these cells between postnatal days 10 and 20. While the spatial distribution of gephyrin clusters was not affected by the distance from the cell body at postnatal day 10, we found that distal dendritic segments appeared to have a higher gephyrin density at later developmental stages. We also show a transient increase around postnatal day 20 in the percentage of spines that are carrying a gephyrin cluster, indicative of innervation by a GABAergic terminal. Since the precise spatial arrangement of synaptic inputs is an important determinant of neuronal responses, we believe that the method described in this work may allow a better understanding of how inhibition settles together with excitation, and serve as basics for further modelling studies focusing on the geometry of dendritic inhibition during development.

  15. Microdrilled cartilage defects treated with thrombin-solidified chitosan/blood implant regenerate a more hyaline, stable, and structurally integrated osteochondral unit compared to drilled controls.

    Science.gov (United States)

    Marchand, Catherine; Chen, Gaoping; Tran-Khanh, Nicolas; Sun, Jun; Chen, Hongmei; Buschmann, Michael D; Hoemann, Caroline D

    2012-03-01

    This study analyzed the long-term cartilage and subchondral bone repair of microdrilled defects treated with chitosan glycerol-phosphate/blood implant, using thrombin (Factor IIa) to accelerate in situ solidification. We also evaluated the cartilage repair response to six smaller microdrill holes compared with two larger holes. Bilateral knee trochlear cartilage defects were created in n=8 skeletally mature rabbits, drilled with six proximal 0.5 mm and two distal 0.9 mm holes, then covered with in situ-solidified IIa-implants (treated) or with IIa-alone (control). After 6.5 months of repair, cartilage repair tissues were analyzed by histological scoring and histomorphometry for hyaline matrix characteristics and osseous integration. Subchondral repair bone was analyzed by 3D microcomputed tomography and compared to acute defects (n=6) and intact trochlea (n=8). Implant-treated cartilage repair tissues had higher structural integrity through the entire defect (p=0.02), twofold higher percent staining for glycosaminoglycan (p=0.0004), and ~24% more collagen type II staining over the smaller drill holes (p=0.008) compared with controls. Otherwise, hole diameter had no specific effect on cartilage repair. The subchondral bone plate was partially restored in treated and control defects but less dense than intact trochlea, with evidence of incomplete regeneration of the calcified cartilage layer. More residual drill holes (p=0.054) were detected in control versus treated defects, and control defects with more than 40% residual holes presented abnormally thicker trabeculae compared with treated defects. Low osteoclast numbers after 6.5 months repair suggested that bone was no longer remodeling. The subchondral bone plate surrounding the defects exhibited a significant thickening compared with age-matched intact trochlea. These data suggest that debridement and drilling can lead to long-term subchondral bone changes outside the cartilage defect. Compared with drilled

  16. Morphology evolution of hydrothermally grown ZnO nanostructures on gallium doping and their defect structures

    Energy Technology Data Exchange (ETDEWEB)

    Pineda-Hernandez, G. [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico); Escobedo-Morales, A., E-mail: alejandroescobedo@hotmail.com [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico); Pal, U. [Instituto de Fisica, Benemerita Universidad Autonoma de Puebla, Apdo. Postal J-48, C.P. 72570 Puebla, Pue. (Mexico); Chigo-Anota, E. [Facultad de Ingenieria Quimica, Benemerita Universidad Autonoma de Puebla, C.P. 72570 Puebla, Pue. (Mexico)

    2012-08-15

    In the present article, the effect of gallium doping on the morphology, structural, and vibrational properties of hydrothermally grown ZnO nanostructures has been studied. It has been observed that incorporated gallium plays an important role on the growth kinetics and hence on the morphology evolution of the ZnO crystals. Ga doping in high concentration results in the contraction of ZnO unit cell, mainly along c-axis. Although Ga has high solubility in ZnO, heavy doping promotes the segregation of Ga atoms as a secondary phase. Incorporated Ga atoms strongly affect the vibrational characteristics of ZnO lattice and induce anomalous Raman modes. Possible mechanisms of morphology evolution and origin of anomalous Raman modes in Ga doped ZnO nanostructures are discussed. -- Highlights: Black-Right-Pointing-Pointer Ga doped ZnO nanostructures were successfully grown by hydrothermal chemical route. Black-Right-Pointing-Pointer Ga doping has strong effect on the resulting morphology of ZnO nanostructures. Black-Right-Pointing-Pointer Anomalous vibrational modes in wurtzite ZnO lattice are induced by Ga doping. Black-Right-Pointing-Pointer Incorporated Ga atoms accommodate at preferential lattice sites.

  17. Defects at oxide surfaces

    CERN Document Server

    Thornton, Geoff

    2015-01-01

    This book presents the basics and characterization of defects at oxide surfaces. It provides a state-of-the-art review of the field, containing information to the various types of surface defects, describes analytical methods to study defects, their chemical activity and the catalytic reactivity of oxides. Numerical simulations of defective structures complete the picture developed. Defects on planar surfaces form the focus of much of the book, although the investigation of powder samples also form an important part. The experimental study of planar surfaces opens the possibility of applying the large armoury of techniques that have been developed over the last half-century to study surfaces in ultra-high vacuum. This enables the acquisition of atomic level data under well-controlled conditions, providing a stringent test of theoretical methods. The latter can then be more reliably applied to systems such as nanoparticles for which accurate methods of characterization of structure and electronic properties ha...

  18. Boron-substitution and defects in B2-type AlNi compound: Site-preference and influence on structural, thermodynamic and electronic properties

    Energy Technology Data Exchange (ETDEWEB)

    Capaz, Rodrigo B. [Instituto de Física, Universidade Federal do Rio de Janeiro, Caixa Postal 68528, Rio de Janeiro, RJ 21941-972 (Brazil); ElMassalami, M., E-mail: massalam@if.ufrj.br [Instituto de Física, Universidade Federal do Rio de Janeiro, Caixa Postal 68528, Rio de Janeiro, RJ 21941-972 (Brazil); Terrazos, L.A. [Centro de Educação e Saúde, Universidade Federal de Campina Grande, Cuité, PB 58175-000 (Brazil); Elhadi, M. [Instituto de Física, Universidade Federal do Rio de Janeiro, Caixa Postal 68528, Rio de Janeiro, RJ 21941-972 (Brazil); Takeya, H. [National Institute for Materials Science, 1-2-1, Sengen, Tsukuba, 305-0047 (Japan); Ghivelder, L. [Instituto de Física, Universidade Federal do Rio de Janeiro, Caixa Postal 68528, Rio de Janeiro, RJ 21941-972 (Brazil)

    2016-06-05

    Using a combination of theoretical (first-principles total-energy and electronic structure calculations) as well as experimental (structural, thermodynamics) techniques, we systematically investigated the influence of B incorporation on the structural, electronic and thermodynamic properties of a series of technologically-important B-containing AlNi matrix. Special attention was paid to calculating the energy cost of placing B at various sites within the cubic unit cell. The most energetically favorable defects were identified to be, depending on initial stoichiometry, substitutional B at Al site (B{sub Al}), Ni vacancy (V{sub Ni}), or Ni antisite (Ni{sub Al}). We show that the induced variation in the lattice parameters can be correlated with the type and concentration of the involved defects: e.g. the surge of V{sub Ni} defects leads to a stronger lattice-parameter reduction, that of Ni{sub Al} ones to a relatively weaker reduction while that of B{sub Al} defects to a much weaker influence. Both electronic band structure calculations as well as thermodynamics measurements indicate that the 3d bands of Ni are fully occupied and magnetically unpolarized and that the resulting N(E{sub F}) is very small: all studied compounds are normal conductors with no trace of superconductivity or magnetic polarization.

  19. Marker-assisted pyramiding of Thinopyrum-derived leaf rust ...

    Indian Academy of Sciences (India)

    Mona Singh

    2017-12-08

    Dec 8, 2017 ... Abstract. This study was undertaken to pyramid two effective leaf rust resistance genes (Lr19 and Lr24) derived from ... genes such as Lr9, Lr19, Lr26 and Lr28 became ineffective ..... Disease management recommendations.

  20. How They (Should Have) Built the Pyramids

    Science.gov (United States)

    Gallagher, Gregory; West, Joseph; Waters, Kevin

    2014-03-01

    A novel ``polygon method'' is proposed for moving large stone blocks. The method is implemented by the attachment of rods of analytically chosen radii to the block by means of rope. The chosen rods are placed on each side of the square-prism block in order to transform the square prism into a prism of higher order polygon, i.e. octagon, dodecagon etc. Experimental results are presented and compared to other methods proposed by the authors, including a dragging method and a rail method which includes the idea of dragging the block on rails made from arbitrarily chosen rod-shaped ``tracks,'' and to independent work by another group which utilized wooden attachments providing a cylindrical shape. It is found that the polygon method when used on small scale stone blocks across level open ground has an equivalent of a coefficient of friction order of 0.1. For full scale pyramid blocks, the wooden ``rods'' would need to be of order 30 cm in diameter, certainly within reason, given the diameter of wooden masts used on ships in that region during the relevant time period in Egypt. This project also inspired a ``spin-off'' project in which the behavior or rolling polygons is investigated and preliminary data is presented.

  1. Repairing Nanoparticle Surface Defects

    NARCIS (Netherlands)

    Marino, Emanuele; Kodger, Thomas E.; Crisp, R.W.; Timmerman, Dolf; MacArthur, Katherine E.; Heggen, Marc; Schall, Peter

    2017-01-01

    Solar devices based on semiconductor nanoparticles require the use of conductive ligands; however, replacing the native, insulating ligands with conductive metal chalcogenide complexes introduces structural defects within the crystalline nanostructure that act as traps for charge carriers. We

  2. Fabrication method, structure, mechanical, and biological properties of decellularized extracellular matrix for replacement of wide bone tissue defects.

    Science.gov (United States)

    Anisimova, N Y; Kiselevsky, M V; Sukhorukova, I V; Shvindina, N V; Shtansky, D V

    2015-09-01

    The present paper was focused on the development of a new method of decellularized extracellular matrix (DECM) fabrication via a chemical treatment of a native bone tissue. Particular attention was paid to the influence of chemical treatment on the mechanical properties of native bones, sterility, and biological performance in vivo using the syngeneic heterotopic and orthotopic implantation models. The obtained data indicated that after a chemical decellularization treatment in 4% aqueous sodium chlorite, no noticeable signs of the erosion of compact cortical bone surface or destruction of trabeculae of spongy bone in spinal channel were observed. The histological studies showed that the chemical treatment resulted in the decellularization of both bone and cartilage tissues. The DECM samples demonstrated no signs of chemical and biological degradation in vivo. Thorough structural characterization revealed that after decellularization, the mineral frame retained its integrity with the organic phase; however clotting and destruction of organic molecules and fibers were observed. FTIR studies revealed several structural changes associated with the destruction of organic molecules, although all organic components typical of intact bone were preserved. The decellularization-induced structural changes in the collagen constituent resulted changed the deformation under compression mechanism: from the major fracture by crack propagation throughout the sample to the predominantly brittle fracture. Although the mechanical properties of radius bones subjected to decellularization were observed to degrade, the mechanical properties of ulna bones in compression and humerus bones in bending remained unchanged. The compressive strength of both the intact and decellularized ulna bones was 125-130 MPa and the flexural strength of humerus bones was 156 and 145 MPa for the intact and decellularized samples, respectively. These results open new avenues for the use of DECM samples as

  3. Electrochemical transformations of oxygen and the defect structure of solid solutions on the basis of alkaline earth metal ortho-vanadates

    International Nuclear Information System (INIS)

    Khodos, M.Ya.; Belysheva, G.M.; Brajnina, Kh.Z.

    1986-01-01

    Effect of iso- and heterovalent substitution in the structure of alkaline earth metal ortho-vanadates and synthesis conditions, simulating the definite type of their crystal lattice disordering, on the character of potentiodynamic anodic-cathodic curves has been investigated by the method of cyclic voltammetry. Correlation between signals observed and the defect structure of oxide compounds is refined. Oxygen chemisorption is shown to be determined by concentration of nonequilibrium oxygen vacancies, which formation is accompanied by appearance of quasi-free electrons

  4. Conserved size and periodicity of pyramidal patches in layer 2 of medial/caudal entorhinal cortex.

    Science.gov (United States)

    Naumann, Robert K; Ray, Saikat; Prokop, Stefan; Las, Liora; Heppner, Frank L; Brecht, Michael

    2016-03-01

    To understand the structural basis of grid cell activity, we compare medial entorhinal cortex architecture in layer 2 across five mammalian species (Etruscan shrews, mice, rats, Egyptian fruit bats, and humans), bridging ∼100 million years of evolutionary diversity. Principal neurons in layer 2 are divided into two distinct cell types, pyramidal and stellate, based on morphology, immunoreactivity, and functional properties. We confirm the existence of patches of calbindin-positive pyramidal cells across these species, arranged periodically according to analyses techniques like spatial autocorrelation, grid scores, and modifiable areal unit analysis. In rodents, which show sustained theta oscillations in entorhinal cortex, cholinergic innervation targeted calbindin patches. In bats and humans, which only show intermittent entorhinal theta activity, cholinergic innervation avoided calbindin patches. The organization of calbindin-negative and calbindin-positive cells showed marked differences in entorhinal subregions of the human brain. Layer 2 of the rodent medial and the human caudal entorhinal cortex were structurally similar in that in both species patches of calbindin-positive pyramidal cells were superimposed on scattered stellate cells. The number of calbindin-positive neurons in a patch increased from ∼80 in Etruscan shrews to ∼800 in humans, only an ∼10-fold over a 20,000-fold difference in brain size. The relatively constant size of calbindin patches differs from cortical modules such as barrels, which scale with brain size. Thus, selective pressure appears to conserve the distribution of stellate and pyramidal cells, periodic arrangement of calbindin patches, and relatively constant neuron number in calbindin patches in medial/caudal entorhinal cortex. © 2015 The Authors. The Journal of Comparative Neurology Published by Wiley Periodicals, Inc.

  5. Conserved size and periodicity of pyramidal patches in layer 2 of medial/caudal entorhinal cortex

    Science.gov (United States)

    Naumann, Robert K.; Ray, Saikat; Prokop, Stefan; Las, Liora; Heppner, Frank L.

    2016-01-01

    ABSTRACT To understand the structural basis of grid cell activity, we compare medial entorhinal cortex architecture in layer 2 across five mammalian species (Etruscan shrews, mice, rats, Egyptian fruit bats, and humans), bridging ∼100 million years of evolutionary diversity. Principal neurons in layer 2 are divided into two distinct cell types, pyramidal and stellate, based on morphology, immunoreactivity, and functional properties. We confirm the existence of patches of calbindin‐positive pyramidal cells across these species, arranged periodically according to analyses techniques like spatial autocorrelation, grid scores, and modifiable areal unit analysis. In rodents, which show sustained theta oscillations in entorhinal cortex, cholinergic innervation targeted calbindin patches. In bats and humans, which only show intermittent entorhinal theta activity, cholinergic innervation avoided calbindin patches. The organization of calbindin‐negative and calbindin‐positive cells showed marked differences in entorhinal subregions of the human brain. Layer 2 of the rodent medial and the human caudal entorhinal cortex were structurally similar in that in both species patches of calbindin‐positive pyramidal cells were superimposed on scattered stellate cells. The number of calbindin‐positive neurons in a patch increased from ∼80 in Etruscan shrews to ∼800 in humans, only an ∼10‐fold over a 20,000‐fold difference in brain size. The relatively constant size of calbindin patches differs from cortical modules such as barrels, which scale with brain size. Thus, selective pressure appears to conserve the distribution of stellate and pyramidal cells, periodic arrangement of calbindin patches, and relatively constant neuron number in calbindin patches in medial/caudal entorhinal cortex. J. Comp. Neurol. 524:783–806, 2016. © 2015 The Authors. The Journal of Comparative Neurology Published by Wiley Periodicals, Inc. PMID:26223342

  6. Two new octahedral/pyramidal frameworks containing both cation channels and lone-pair channels: syntheses and structures of Ba2MnIIMn2III(SeO3)6 and PbFe2(SeO3)4

    International Nuclear Information System (INIS)

    Johnston, Magnus G.; Harrison, William T.A.

    2004-01-01

    The hydrothermal syntheses, single crystal structures, and some properties of Ba 2 Mn II Mn 2 III (SeO 3 ) 6 and PbFe 2 (SeO 3 ) 4 are reported. These related phases contain three-dimensional frameworks of vertex (FeO 6 ) and vertex/edge linked (MnO 6 ) octahedra and SeO 3 pyramids. In each case, the MO 6 /SeO 3 framework encloses two types of 8 ring channels, one of which encapsulates the extra-framework cations and one of which provides space for the Se IV lone pairs. Crystal data: Ba 2 Mn 3 (SeO 3 ) 6 , M r =1201.22, monoclinic, P2 1 /c (No. 14), a=5.4717 (3)A, b=9.0636 (4)A, c=17.6586 (9)A, β=94.519 (1) o , V=873.03 (8)A 3 , Z=2, R(F)=0.031, wR(F 2 )=0.070; PbFe 2 (SeO 3 ) 4 , M r =826.73, triclinic, P1-bar (No. 2), a=5.2318 (5)A, b=6.7925 (6)A, c=7.6445 (7)A, α=94.300 (2) o , β=90.613 (2) o , γ=95.224 (2) o , V=269.73 (4)A 3 , Z=1, R(F)=0.051, wR(F 2 )=0.131

  7. A possible explanation of the void discovered in the pyramid of Khufu on the basis of the pyramid texts

    OpenAIRE

    Magli, Giulio

    2017-01-01

    A recent exploration has shown the presence of a significant void in the pyramid of Khufu at Giza. A possible explanation of this space, interpreted as a chamber connected to the lower north channel and aimed to contain a specific funerary equipment is tentatively proposed. According to the Pyramid Texts, this equipment might consist of a Iron throne, actually a wooden throne endowed with meteoritic Iron sheets.

  8. Ultra high-resolution gene centric genomic structural analysis of a non-syndromic congenital heart defect, Tetralogy of Fallot.

    Directory of Open Access Journals (Sweden)

    Douglas C Bittel

    Full Text Available Tetralogy of Fallot (TOF is one of the most common severe congenital heart malformations. Great progress has been made in identifying key genes that regulate heart development, yet approximately 70% of TOF cases are sporadic and nonsyndromic with no known genetic cause. We created an ultra high-resolution gene centric comparative genomic hybridization (gcCGH microarray based on 591 genes with a validated association with cardiovascular development or function. We used our gcCGH array to analyze the genomic structure of 34 infants with sporadic TOF without a deletion on chromosome 22q11.2 (n male = 20; n female = 14; age range of 2 to 10 months. Using our custom-made gcCGH microarray platform, we identified a total of 613 copy number variations (CNVs ranging in size from 78 base pairs to 19.5 Mb. We identified 16 subjects with 33 CNVs that contained 13 different genes which are known to be directly associated with heart development. Additionally, there were 79 genes from the broader list of genes that were partially or completely contained in a CNV. All 34 individuals examined had at least one CNV involving these 79 genes. Furthermore, we had available whole genome exon arrays from right ventricular tissue in 13 of our subjects. We analyzed these for correlations between copy number and gene expression level. Surprisingly, we could detect only one clear association between CNVs and expression (GSTT1 for any of the 591 focal genes on the gcCGH array. The expression levels of GSTT1 were correlated with copy number in all cases examined (r = 0.95, p = 0.001. We identified a large number of small CNVs in genes with varying associations with heart development. Our results illustrate the complexity of human genome structural variation and underscore the need for multifactorial assessment of potential genetic/genomic factors that contribute to congenital heart defects.

  9. Structural modeling of tissue-specific mitochondrial alanyl-tRNA synthetase (AARS2 defects predicts differential effects on aminoacylation

    Directory of Open Access Journals (Sweden)

    Liliya eEuro

    2015-02-01

    Full Text Available The accuracy of mitochondrial protein synthesis is dependent on the coordinated action of nuclear-encoded mitochondrial aminoacyl-tRNA synthetases (mtARSs and the mitochondrial DNA-encoded tRNAs. The recent advances in whole-exome sequencing have revealed the importance of the mtARS proteins for mitochondrial pathophysiology since nearly every nuclear gene for mtARS (out of 19 is now recognized as a disease gene for mitochondrial disease. Typically, defects in each mtARS have been identified in one tissue-specific disease, most commonly affecting the brain, or in one syndrome. However, mutations in the AARS2 gene for mitochondrial alanyl-tRNA synthetase (mtAlaRS have been reported both in patients with infantile-onset cardiomyopathy and in patients with childhood to adulthood-onset leukoencephalopathy. We present here an investigation of the effects of the described mutations on the structure of the synthetase, in an effort to understand the tissue-specific outcomes of the different mutations.The mtAlaRS differs from the other mtARSs because in addition to the aminoacylation domain, it has a conserved editing domain for deacylating tRNAs that have been mischarged with incorrect amino acids. We show that the cardiomyopathy phenotype results from a single allele, causing an amino acid change p.R592W in the editing domain of AARS2, whereas the leukodystrophy mutations are located in other domains of the synthetase. Nevertheless, our structural analysis predicts that all mutations reduce the aminoacylation activity of the synthetase, because all mtAlaRS domains contribute to tRNA binding for aminoacylation. According to our model, the cardiomyopathy mutations severely compromise aminoacylation whereas partial activity is retained by the mutation combinations found in the leukodystrophy patients. These predictions provide a hypothesis for the molecular basis of the distinct tissue-specific phenotypic outcomes.

  10. The Differences between Multilevel Marketing and the Financial Pyramids or “Pyramid Scheme”

    Directory of Open Access Journals (Sweden)

    Vanessa Braga Santos

    2017-06-01

    Full Text Available This research aims to analyze and understand the difference between the concept of Multilevel Marketing and the Financial Pyramids. The main objective of this work is to clarify the differences between these two business models that are growing worldwide and also present concepts that show the success of professionals in this kind of new business model. Multilevel Marketing shows a sustainable system, a direct selling business that includes recruiting distributors with a profit share and also by recruiting new members. In the Financial Pyramid concept, the problem is that business support is the network itself, and often there are no products to be commercialized, so this model is unsustainable and considered as an illegal business in several countries, including Brazil. Within this approach, a case study was conducted with one of the largest Multilevel Marketing companies in the world, Mary Kay. We conducted a direct interview with one of Mary Kay Independent Sales Directors from the city of Piracicaba, held in October 2016, and collected data surveys from the internet. The markets today are based on moving products, so we concluded that Multilevel Marketing is a great business opportunity to make an extra income by marketing services and products.

  11. Structure and strain relaxation effects of defects in In{sub x}Ga{sub 1–x}N epilayers

    Energy Technology Data Exchange (ETDEWEB)

    Rhode, S. L., E-mail: sr583@cam.ac.uk; Fu, W. Y.; Massabuau, F. C.-P.; Kappers, M. J.; McAleese, C.; Oehler, F.; Humphreys, C. J.; Sahonta, S.-L. [Department of Materials Science and Metallurgy, University of Cambridge, Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Moram, M. A. [Department of Materials Science and Metallurgy, University of Cambridge, Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Department of Materials, Imperial College London, Exhibition Road, London SW7 2AZ (United Kingdom); Dusane, R. O. [Department of Metallurgical Engineering and Materials Science, Indian Institute of Technology Bombay, Mumbai 400076 (India)

    2014-09-14

    The formation of trench defects is observed in 160 nm-thick In{sub x}Ga{sub 1–x}N epilayers with x≤0.20, grown on GaN on (0001) sapphire substrates using metalorganic vapour phase epitaxy. The trench defect density increases with increasing indium content, and high resolution transmission electron microscopy shows an identical structure to those observed previously in InGaN quantum wells, comprising meandering stacking mismatch boundaries connected to an I₁-type basal plane stacking fault. These defects do not appear to relieve in-plane compressive strain. Other horizontal sub-interface defects are also observed within the GaN pseudosubstrate layer of these samples and are found to be pre-existing threading dislocations which form half-loops by bending into the basal plane, and not basal plane stacking faults, as previously reported by other groups. The origins of these defects are discussed and are likely to originate from a combination of the small in-plane misorientation of the sapphire substrate and the thermal mismatch strain between the GaN and InGaN layers grown at different temperatures.

  12. PKA spectral effects on subcascade structures and free defect survival ratio as estimated by cascade-annealing computer simulation

    International Nuclear Information System (INIS)

    Muroga, Takeo

    1990-01-01

    The free defect survival ratio is calculated by ''cascade-annealing'' computer simulation using the MARLOWE and modified DAIQUIRI codes in various cases of Primary Knock-on Atom (PKA) spectra. The number of subcascades is calculated by ''cut-off'' calculation using MARLOWE. The adequacy of these methods is checked by comparing the results with experiments (surface segregation measurements and Transmission Electron Microscope cascade defect observations). The correlation using the weighted average recoil energy as a parameter shows that the saturation of the free defect survival ratio at high PKA energies has a close relation to the cascade splitting into subcascades. (author)

  13. Repairing rabbit radial defects by combining bone marrow stroma stem cells with bone scaffold material comprising a core-cladding structure.

    Science.gov (United States)

    Wu, H; Liu, G H; Wu, Q; Yu, B

    2015-10-05

    We prepared a bone scaffold material comprising a PLGA/β-TCP core and a Type I collagen cladding, and recombined it with bone marrow stroma stem cells (BMSCs) to evaluate its potential for use in bone tissue engineering by in vivo and in vitro experiments. PLGA/β-TCP without a cladding was used for comparison. The adherence rate of the BMSCs to the scaffold was determined by cell counting. Cell proliferation rate was determined by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide method. The osteogenic capability was evaluated by alkaline phosphatase activity. The scaffold materials were recombined with the BMSCs and implanted into a large segmental rabbit radial defect model to evaluate defect repair. Osteogenesis was assessed in the scaffold materials by histological and double immunofluorescence labeling, etc. The adherence number, proliferation number, and alkaline phosphatase expression of the cells on the bone scaffold material with core-cladding structure were significantly higher than the corresponding values in the PLGA/β-TCP composite scaffold material (P structure completely degraded at the bone defect site and bone formation was completed. The rabbit large sentimental radial defect was successfully repaired. The degradation and osteogenesis rates matched well. The bone scaffold with core-cladding structure exhibited better osteogenic activity and capacity to repair a large segmental bone defect compared to the PLGA/β-TCP composite scaffold. The bone scaffold with core-cladding structure has excellent physical properties and biocompatibility. It is an ideal scaffold material for bone tissue engineering.

  14. Housing under the pyramid reduces susceptibility of hippocampal CA3 pyramidal neurons to prenatal stress in the developing rat offspring.

    Science.gov (United States)

    Murthy, Krishna Dilip; George, Mitchel Constance; Ramasamy, Perumal; Mustapha, Zainal Arifin

    2013-12-01

    Mother-offspring interaction begins before birth. The foetus is particularly vulnerable to environmental insults and stress. The body responds by releasing excess of the stress hormone cortisol, which acts on glucocorticoid receptors. Hippocampus in the brain is rich in glucocorticoid receptors and therefore susceptible to stress. The stress effects are reduced when the animals are placed under a model wooden pyramid. The present study was to first explore the effects of prenatal restraint-stress on the plasma corticosterone levels and the dendritic arborisation of CA3 pyramidal neurons in the hippocampus of the offspring. Further, to test whether the pyramid environment would alter these effects, as housing under a pyramid is known to reduce the stress effects, pregnant Sprague Dawley rats were restrained for 9 h per day from gestation day 7 until parturition in a wire-mesh restrainer. Plasma corticosterone levels were found to be significantly increased. In addition, there was a significant reduction in the apical and the basal total dendritic branching points and intersections of the CA3 hippocampal pyramidal neurons. The results thus suggest that, housing in the pyramid dramatically reduces prenatal stress effects in rats.

  15. Shift of the pyramidal tract during resection of the intraaxial brain tumors estimated by intraoperative diffusion-weighted imaging

    International Nuclear Information System (INIS)

    Ozawa, Norihiko; Muragaki, Yoshihiro; Nakamura, Ryoichi; Iseki, Hiroshi; Hori, Tomokatsu

    2009-01-01

    The present study evaluated the shift of the pyramidal tract during resection of 17 proximal intraaxial brain tumors. In each case intraoperative diffusion-weighted (iDW) magnetic resonance imaging with a motion-probing gradient applied in the anteroposterior direction was performed using a scanner with a 0.3 T vertical magnetic field. The position of the white matter bundles containing the pyramidal tract was estimated on the coronal images before and after resection of the neoplasm, and both quantitative and directional evaluation of its displacement was done. In all cases iDW imaging provided visualization of the structure of interest. The magnitude of the pyramidal tract displacement due to removal of the neoplasm varied from 0.5 to 8.7 mm (mean 4.4±2.5 mm) on the lesion side and from 0 to 3.6 mm (mean 1.3±1.1 mm) on the normal side (p<0.001). Tumor location in regards to the pyramidal tract was significantly associated with the direction of the pyramidal tract displacement (p<0.05). Outward shift occurred in 10 out of 13 cases of the lateral neoplasms, whereas in all 4 superomedial tumors inward shift was marked. In conclusion, the direction of the pyramidal tract displacement during resection of the proximal intraaxial brain tumors is mainly determined by position of the neoplasm, but can be unpredictable in some cases, which necessitates use of subcortical brain mapping and intraoperative imaging, particularly iDW imaging with updated neuronavigation. (author)

  16. Intraoperative tractography and neuronavigation of the pyramidal tract

    International Nuclear Information System (INIS)

    Nimsky, C.; Ganslandt, O.; Weigel, D.; Keller, B. von; Stadlbauer, A.; Akutsu, H.; Hammen, T.; Buchfelder, M.

    2008-01-01

    Diffusion tensor imaging (DTI) based fiber tracking was applied to visualize the course of the pyramidal tract in the surgical field by microscope-based navigation. In 70 patients with lesions adjacent to the pyramidal tract, DTI data were integrated in a navigational setup. Diffusion data (b=0) were rigidly registered with standard T1-weighted 3-D images. Fiber tracking was performed applying a tensor-deflection algorithm using a multiple volume of interest approach as seed regions for tracking. fMRI data identifying the motor gyrus were applied as selection criteria to define the fibers of interest. After tracking, a 3-D object was generated representing the pyramidal tract. In selected cases, the intraoperative image data (1.5 T intraoperative MRI) were used to update the navigation system. In all patients the pyramidal tract could be visualized in the operative field applying the heads-up display of the operating microscope. In 8 patients (11%) a new or aggravated postoperative paresis could be observed, which was transient in 5 of them; thus, only in 3 patients (4.2%) was there a new permanent neurological deficit. Intraoperative imaging depicted a shifting of the pyramidal tract which amounted up to 15 mm; even the direction of shifting was variable and could not be predicted before surgery, so that mathematical models trying to predict brain shift behaviour are of restricted value only. DTI fiber tracking data can be reliably integrated into navigational systems providing intraoperative visualization of the pyramidal tract. This technique allowed the resection of lesions adjacent to the pyramidal tract with low morbidity. (author)

  17. Combining Simulated and Experimental Data to Simulate Ultrasonic Array Data From Defects in Materials With High Structural Noise.

    Science.gov (United States)

    Bloxham, Harry A; Velichko, Alexander; Wilcox, Paul David

    2016-12-01

    Ultrasonic nondestructive testing inspections using phased arrays are performed on a wide range of components and materials. All real inspections suffer, to varying extents, from coherent noise, including image artifacts and speckle caused by complex geometries and grain scatter, respectively. By its nature, this noise is not reduced by averaging; however, it degrades the signal-to-noise ratio of defects and ultimately limits their detectability. When evaluating the effectiveness of an inspection, a large pool of data from samples containing a range of different defects are important to estimate the probability of detection of defects and to help characterize them. For a given inspection, coherent noise is easy to measure experimentally but hard to model realistically. Conversely, the ultrasonic response of defects can be simulated relatively easily. This paper proposes a novel method of simulating realistic array data by combining noise-free simulations of defect responses with coherent noise taken from experimental data. This removes the need for costly physical samples with known defects to be made and allows for large data sets to be created easily.

  18. Study on nano-structured hydroxyapatite/zirconia stabilized yttria on healing of articular cartilage defect in rabbit

    Directory of Open Access Journals (Sweden)

    Amir Sotoudeh

    2013-05-01

    Full Text Available PURPOSE: Articular Cartilage has limited potential for self-repair and tissue engineering approaches attempt to repair articular cartilage by scaffolds. We hypothesized that the combined hydroxyapatite and zirconia stabilized yttria would enhance the quality of cartilage healing. METHODS: In ten New Zealand white rabbits bilateral full-thickness osteochondral defect, 4 mm in diameter and 3 mm depth, was created on the articular cartilage of the patellar groove of the distal femur. In group I the scaffold was implanted into the right stifle and the same defect was created in the left stifle without any transplant (group II. Specimens were harvested at 12 weeks after implantation, examined histologically for morphologic features, and stained immunohistochemically for type-II collagen. RESULTS: In group I the defect was filled with a white translucent cartilage tissue In contrast, the defects in the group II remained almost empty. In the group I, the defects were mostly filled with hyaline-like cartilage evidenced but defects in group II were filled with fibrous tissue with surface irregularities. Positive immunohistochemical staining of type-II collagen was observed in group I and it was absent in the control group. CONCLUSION: The hydroxyapatite/yttria stabilized zirconia scaffold would be an effective scaffold for cartilage tissue engineering.

  19. Novel tri-modal defect structure in Nb-doped MOCVD Y Ba2Cu3O7: a paradigm for pinning landscape control

    International Nuclear Information System (INIS)

    Aytug, Tolga; Zuev, Yuri; Specht, Eliot D; Parans Paranthaman, M; Maroni, Victor A; Miller, Dean J; Chen, Zhijun; Jeremy Kropf, A; Zaluzec, Nestor J

    2012-01-01

    Immobilization of vortices, or flux pinning, is both an enduring scientific issue and one of the most important problems in optimizing high temperature superconductors (HTSs) for commercial use. Here, we demonstrate a practical approach to the creation of a multi-modal flux pinning landscape in Y Ba 2 Cu 3 O 7 (YBCO) films employing an industrially scalable metal–organic chemical vapor deposition technique. Through controlled additions of Nb, we have achieved a novel distribution of crystallographic defects that immobilize (pin) vortices in the YBCO matrix. That is, with only the addition of a single dopant element, a tri-modal, non-superconducting defect structure is induced that threads through the YBCO matrix laterally (parallel to the ab planes of YBCO), vertically (parallel to the YBCO c-axis), and isotropically in the form of random spherical defects. For optimally doped samples, the influence of these multi-modal nanocrystalline defect structures on the flux pinning properties manifests itself as a significant improvement in the critical current density (J c ) for all magnetic field orientations. The results demonstrate the possibility of achieving an ideal flux pinning landscape (from an orientation and strength viewpoint), which permits the design of HTS wires with fully-tunable properties by processes suitable for large-scale manufacturing. (paper)

  20. Defect induced structural inhomogeneity, ultraviolet light emission and near-band-edge photoluminescence broadening in degenerate In2O3 nanowires

    Science.gov (United States)

    Mukherjee, Souvik; Sarkar, Ketaki; Wiederrecht, Gary P.; Schaller, Richard D.; Gosztola, David J.; Stroscio, Michael A.; Dutta, Mitra

    2018-04-01

    We demonstrate here defect induced changes on the morphology and surface properties of indium oxide (In2O3) nanowires and further study their effects on the near-band-edge (NBE) emission, thereby showing the significant influence of surface states on In2O3 nanostructure based device characteristics for potential optoelectronic applications. In2O3 nanowires with cubic crystal structure (c-In2O3) were synthesized via carbothermal reduction technique using a gold-catalyst-assisted vapor-liquid-solid method. Onset of strong optical absorption could be observed at energies greater than 3.5 eV consistent with highly n-type characteristics due to unintentional doping from oxygen vacancy ({V}{{O}}) defects as confirmed using Raman spectroscopy. A combination of high resolution transmission electron microscopy, x-ray photoelectron spectroscopy and valence band analysis on the nanowire morphology and stoichiometry reveals presence of high-density of {V}{{O}} defects on the surface of the nanowires. As a result, chemisorbed oxygen species can be observed leading to upward band bending at the surface which corresponds to a smaller valence band offset of 2.15 eV. Temperature dependent photoluminescence (PL) spectroscopy was used to study the nature of the defect states and the influence of the surface states on the electronic band structure and NBE emission has been discussed. Our data reveals significant broadening of the NBE PL peak consistent with impurity band broadening leading to band-tailing effect from heavy doping.

  1. Defect induced structural inhomogeneity, ultraviolet light emission and near-band-edge photoluminescence broadening in degenerate In 2 O 3 nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, Souvik; Sarkar, Ketaki; Wiederrecht, Gary P.; Schaller, Richard D.; Gosztola, David J.; Stroscio, Michael A.; Dutta, Mitra

    2018-03-01

    We demonstrate here defect induced changes on the morphology and surface properties of indium oxide (In2O3) nanowires and further study their effects on the near-band-edge (NBE) emission, thereby showing the significant influence of surface states on In2O3 nanostructure based device characteristics for potential optoelectronic applications. In2O3 nanowires with cubic crystal structure (c-In2O3) were synthesized via carbothermal reduction technique using a gold-catalyst-assisted vapor–liquid–solid method. Onset of strong optical absorption could be observed at energies greater than 3.5 eV consistent with highly n-type characteristics due to unintentional doping from oxygen vacancy (VO) defects as confirmed using Raman spectroscopy. A combination of high resolution transmission electron microscopy, x-ray photoelectron spectroscopy and valence band analysis on the nanowire morphology and stoichiometry reveals presence of high-density of VO defects on the surface of the nanowires. As a result, chemisorbed oxygen species can be observed leading to upward band bending at the surface which corresponds to a smaller valence band offset of 2.15 eV. Temperature dependent photoluminescence (PL) spectroscopy was used to study the nature of the defect states and the influence of the surface states on the electronic band structure and NBE emission has been discussed. Our data reveals significant broadening of the NBE PL peak consistent with impurity band broadening leading to band-tailing effect from heavy doping.

  2. Target-specific M1 inputs to infragranular S1 pyramidal neurons

    Science.gov (United States)

    Fanselow, Erika E.; Simons, Daniel J.

    2016-01-01

    The functional role of input from the primary motor cortex (M1) to primary somatosensory cortex (S1) is unclear; one key to understanding this pathway may lie in elucidating the cell-type specific microcircuits that connect S1 and M1. Recently, we discovered that a subset of pyramidal neurons in the infragranular layers of S1 receive especially strong input from M1 (Kinnischtzke AK, Simons DJ, Fanselow EE. Cereb Cortex 24: 2237–2248, 2014), suggesting that M1 may affect specific classes of pyramidal neurons differently. Here, using combined optogenetic and retrograde labeling approaches in the mouse, we examined the strengths of M1 inputs to five classes of infragranular S1 neurons categorized by their projections to particular cortical and subcortical targets. We found that the magnitude of M1 synaptic input to S1 pyramidal neurons varies greatly depending on the projection target of the postsynaptic neuron. Of the populations examined, M1-projecting corticocortical neurons in L6 received the strongest M1 inputs, whereas ventral posterior medial nucleus-projecting corticothalamic neurons, also located in L6, received the weakest. Each population also possessed distinct intrinsic properties. The results suggest that M1 differentially engages specific classes of S1 projection neurons, thereby regulating the motor-related influence S1 exerts over subcortical structures. PMID:27334960

  3. Miller's Pyramid and Core Competency Assessment: A Study in Relationship Construct Validity.

    Science.gov (United States)

    Williams, Betsy White; Byrne, Phil D; Welindt, Dillon; Williams, Michael V

    2016-01-01

    Continuous professional development relies on the link between performance and an educational process aimed at improving knowledge and skill. One of the most broadly used frameworks for assessing skills is Miller's Pyramid. This Pyramid has a series of levels of achievement beginning with knowledge (at the base) and ending with routine application in the clinical setting. The purpose of this study was to determine the degree of convergence of two measurement methods, one based on Miller's framework, the second using the Accreditation Council for Graduate Medical Education/American Board of Medical Specialties (ACGME/ABMS) Core Competency framework. The data were gathered from the faculty of a large, Midwestern regional health care provider and hospital system. Data from 264 respondents were studied. The 360° data were from raters of physicians holding supervisory roles in the organization. The scale items were taken from an instrument that has been validated for both structure and known group prediction. The Miller scale was purposely built for this application. The questions were designed to describe each level of the model. The Miller scale was reduced to a single dimension. This result was then regressed on the items from the 360° item ratings. Results of a multivariate analysis of variance isolated a significant relationship between the Miller's Pyramid score and the competency items (P core competencies. Equally important is the finding that while they are related they are not identical. These findings have implications for continuous professional development programing design.

  4. Loss of laminin alpha 1 results in multiple structural defects and divergent effects on adhesion during vertebrate optic cup morphogenesis

    Science.gov (United States)

    Bryan, Chase D.; Chien, Chi-Bin; Kwan, Kristen M.

    2016-01-01

    The vertebrate eye forms via a complex set of morphogenetic events. The optic vesicle evaginates and undergoes transformative shape changes to form the optic cup, in which neural retina and retinal pigmented epithelium enwrap the lens. It has long been known that a complex, glycoprotein-rich extracellular matrix layer surrounds the developing optic cup throughout the process, yet the functions of the matrix and its specific molecular components have remained unclear. Previous work established a role for laminin extracellular matrix in particular steps of eye development, including optic vesicle evagination, lens differentiation, and retinal ganglion cell polarization, yet it is unknown what role laminin might play in the early process of optic cup formation subsequent to the initial step of optic vesicle evagination. Here, we use the zebrafish lama1 mutant (lama1UW1) to determine the function of laminin during optic cup morphogenesis. Using live imaging, we find, surprisingly, that loss of laminin leads to divergent effects on focal adhesion assembly in a spatiotemporally-specific manner, and that laminin is required for multiple steps of optic cup morphogenesis, including optic stalk constriction, invagination, and formation of a spherical lens. Laminin is not required for single cell behaviors and changes in cell shape. Rather, in lama1UW1 mutants, loss of epithelial polarity and altered adhesion lead to defective tissue architecture and formation of a disorganized retina. These results demonstrate that the laminin extracellular matrix plays multiple critical roles regulating adhesion and polarity to establish and maintain tissue structure during optic cup morphogenesis. PMID:27339294

  5. Structural defects and variations in the HIV-1 nef gene from rapid, slow and non-progressor children.

    Science.gov (United States)

    Casartelli, Nicoletta; Di Matteo, Gigliola; Argentini, Claudio; Cancrini, Caterina; Bernardi, Stefania; Castelli, Guido; Scarlatti, Gabriella; Plebani, Anna; Rossi, Paolo; Doria, Margherita

    2003-06-13

    Evaluation of sequence evolution as well as structural defects and mutations of the human immunodeficiency virus-type 1 (HIV-1) nef gene in relation to disease progression in infected children. We examined a large number of nef alleles sequentially derived from perinatally HIV-1-infected children with different rates of disease progression: six non-progressors (NPs), four rapid progressors (RPs), and three slow progressors (SPs). Nef alleles (182 total) were isolated from patients' peripheral blood mononuclear cells (PBMCs), sequenced and analysed for their evolutionary pattern, frequency of mutations and occurrence of amino acid variations associated with different stages of disease. The evolution rate of the nef gene apparently correlated with CD4+ decline in all progression groups. Evidence for rapid viral turnover and positive selection for changes were found only in two SPs and two RPs respectively. In NPs, a higher proportion of disrupted sequences and mutations at various functional motifs were observed. Furthermore, NP-derived Nef proteins were often changed at residues localized in the folded core domain at cytotoxic T lymphocytes (CTL) epitopes (E(105), K(106), E(110), Y(132), K(164), and R(200)), while other residues outside the core domain are more often changed in RPs (A(43)) and SPs (N(173) and Y(214)). Our results suggest a link between nef gene functions and the progression rate in HIV-1-infected children. Moreover, non-progressor-associated variations in the core domain of Nef, together with the genetic analysis, suggest that nef gene evolution is shaped by an effective immune system in these patients.

  6. Local structure and defect chemistry of [(SnSe)1.15]m(TaSe2) ferecrystals – A new type of layered intergrowth compound

    International Nuclear Information System (INIS)

    Grosse, Corinna; Atkins, Ryan; Kirmse, Holm; Mogilatenko, Anna; Neumann, Wolfgang; Johnson, David C.

    2013-01-01

    Highlights: •The crystal structure of [(SnSe) 1.15 ] m (TaSe 2 ) ferecrystals was analyzed by TEM. •The layers exhibit turbostratic disorder, but we also observed a local ordering. •The structures of the SnSe and TaSe 2 layers are similar to binary SnSe and 2H-TaSe 2 . •An increasing in-plane SnSe grain size with increasing m was observed. •Defect areas with missing, substituted or additional layers were found. -- Abstract: The atomic structure of the family of ferecrystals [(SnSe) 1.15 ] m (TaSe 2 ) (m = 1, 3, and 6) was investigated by means of transmission electron microscopy. The tantalum in the TaSe 2 layers was observed to have trigonal prismatic coordination similar to that found in the 2H polytype of bulk TaSe 2 . The structure of the SnSe constituent was found to be similar to that of orthorhombic α-SnSe. In the compounds with m = 1 and m = 3, regions with a local ordering of the layers along a commensurate axis, similar to the ordering in conventional misfit layer compounds, were observed. However, on a longer range the ferecrystals were found to exhibit a turbostratically disordered structure. Stacking defects were occasionally found in the samples in which a layer is interrupted and the surrounding layers are bent around these defects, while maintaining abrupt interfaces instead of interdiffusing. Volume defects were found in one sample of [(SnSe) 1.15 ] 1 (TaSe 2 ) 1 in which a SnSe layer locally substitutes a part of a TaSe 2 layer without interrupting the surrounding layers

  7. SrFe1‑xMoxO2+δ : parasitic ferromagnetism in an infinite-layer iron oxide with defect structures induced by interlayer oxygen

    Science.gov (United States)

    Guo, Jianhui; Shi, Lei; Zhao, Jiyin; Wang, Yang; Yuan, Xueyou; Li, Yang; Wu, Liang

    2018-04-01

    The recent discovered compound SrFeO2 is an infinite-layer-structure iron oxide with unusual square-planar coordination of Fe2+ ions. In this study, SrFe1‑xMoxO2+δ (x parasitic ferromagnetism of the compound and its relationship to the defect structures are investigated. It is found that substitution of high-valent Mo6+ for Fe2+ results in excess oxygen anions O2‑ inserted at the interlayer sites for charge compensation, which further causes large atomic displacements along the c-axis. Due to the robust but flexible Fe-O-Fe framework, the samples are well crystallized within the ab-plane, but are significantly poorer crystallized along the c-axis. Defect structures including local lattice distortions and edge dislocations responsible for the lowered crystallinity are observed by high resolution transmission electron microscopy. Both the magnetic measurements and electron spin resonance spectra provide the evidence of a parasitic ferromagnetism (FM). The week FM interaction originated from the imperfect antiferromagnetic (AFM) ordering could be ascribed to the introduction of uncompensated magnetic moments due to substitution of Mo6+ (S = 0) for Fe2+ (S = 2) and the canted/frustrated spins resulted from defect structures.

  8. Layer 5 Pyramidal Neurons’ Dendritic Remodeling and Increased Microglial Density in Primary Motor Cortex in a Murine Model of Facial Paralysis

    Directory of Open Access Journals (Sweden)

    Diana Urrego

    2015-01-01

    Full Text Available This work was aimed at characterizing structural changes in primary motor cortex layer 5 pyramidal neurons and their relationship with microglial density induced by facial nerve lesion using a murine facial paralysis model. Adult transgenic mice, expressing green fluorescent protein in microglia and yellow fluorescent protein in projecting neurons, were submitted to either unilateral section of the facial nerve or sham surgery. Injured animals were sacrificed either 1 or 3weeks after surgery. Two-photon excitation microscopy was then used for evaluating both layer 5 pyramidal neurons and microglia in vibrissal primary motor cortex (vM1. It was found that facial nerve lesion induced long-lasting changes in the dendritic morphology of vM1 layer 5 pyramidal neurons and in their surrounding microglia. Dendritic arborization of the pyramidal cells underwent overall shrinkage. Apical dendrites suffered transient shortening while basal dendrites displayed sustained shortening. Moreover, dendrites suffered transient spine pruning. Significantly higher microglial cell density was found surrounding vM1 layer 5 pyramidal neurons after facial nerve lesion with morphological bias towards the activated phenotype. These results suggest that facial nerve lesions elicit active dendrite remodeling due to pyramidal neuron and microglia interaction, which could be the pathophysiological underpinning of some neuropathic motor sequelae in humans.

  9. Layer 5 Pyramidal Neurons' Dendritic Remodeling and Increased Microglial Density in Primary Motor Cortex in a Murine Model of Facial Paralysis

    Science.gov (United States)

    Urrego, Diana; Troncoso, Julieta; Múnera, Alejandro

    2015-01-01

    This work was aimed at characterizing structural changes in primary motor cortex layer 5 pyramidal neurons and their relationship with microglial density induced by facial nerve lesion using a murine facial paralysis model. Adult transgenic mice, expressing green fluorescent protein in microglia and yellow fluorescent protein in projecting neurons, were submitted to either unilateral section of the facial nerve or sham surgery. Injured animals were sacrificed either 1 or 3weeks after surgery. Two-photon excitation microscopy was then used for evaluating both layer 5 pyramidal neurons and microglia in vibrissal primary motor cortex (vM1). It was found that facial nerve lesion induced long-lasting changes in the dendritic morphology of vM1 layer 5 pyramidal neurons and in their surrounding microglia. Dendritic arborization of the pyramidal cells underwent overall shrinkage. Apical dendrites suffered transient shortening while basal dendrites displayed sustained shortening. Moreover, dendrites suffered transient spine pruning. Significantly higher microglial cell density was found surrounding vM1 layer 5 pyramidal neurons after facial nerve lesion with morphological bias towards the activated phenotype. These results suggest that facial nerve lesions elicit active dendrite remodeling due to pyramidal neuron and microglia interaction, which could be the pathophysiological underpinning of some neuropathic motor sequelae in humans. PMID:26064916

  10. Direct observation of the point-defect structure of depleted-zones in ion-irradiated metals

    International Nuclear Information System (INIS)

    Wei, C.

    1978-01-01

    The point-defect structure of individual depleted zones has been studied systematically. Four-pass zone-refined tungsten field-ion microscope (FIM) specimens were irradiated in-situ at 10 K with 30 keV Cr + , Mo + , or W + ions to a total dose of (2 to 10) x 10 12 ion cm -2 and examined by the pulse field-evaporation technique at 10 K. The experimental conditions were such that each depleted zone was created by a single incident-ion. The number of vacant lattice sites within a depleted zone was compared with a modified Kinchin--Pease model. The radial distribution function was determined for each depleted zone; it was found that the vacant lattice sites within the volume of each depleted zone tended to exist in a highly clustered state. It was found that the diameter D of each depleted zone was described by the equation D approximately equal to [y 2 ]/sup 1 / 2 / where [y 2 ]/sup 1 / 2 / is the second moment of the theoretical distribution curve, of the fraction of incident ion energy deposited in atom motion, transverse to the direction of the incident ion-beam. The spatial distribution of self-interstitial atoms (SIAs) in a specimen irradiated with 30 keV Cr + ions and in a specimen irradiated with 18 keV Au + ions, at 10 K, was determined. A low bound to the average range of replacement collision sequences (RCSs) was found to be 175 +- 85 A. A detailed FIM study was also made of the vacancy structure of a (220) platelet created by a single 30 keV W + ion in a platinum-4.0 at. % gold alloy; the specimen was irradiated at 40 K and then isochronally warmed to 100 K. The (220) platelet was found to consist of 31 vacant lattice sites, lying in four (220) planes, and clustered in a disc-shaped region which is approximately 20 A in diameter. It was suggested that prismatic dislocation loops lying on (220) type planes in ion or fast neutron irradiated platinum can form as a result of the direct collapse of (220) type vacancy platelets

  11. Use of overburden rocks from open-pit coal mines and waste coals of Western Siberia for ceramic brick production with a defect-free structure

    Science.gov (United States)

    Stolboushkin, A. Yu; Ivanov, A. I.; Storozhenko, G. I.; Syromyasov, V. A.; Akst, D. V.

    2017-09-01

    The rational technology for the production of ceramic bricks with a defect-free structure from coal mining and processing wastes was developed. The results of comparison of physical and mechanical properties and the structure of ceramic bricks manufactured from overburden rocks and waste coal with traditional for semi-dry pressing mass preparation and according to the developed method are given. It was established that a homogeneous, defect-free brick texture obtained from overburden rocks of open-pit mines and waste coal improves the quality of ceramic wall materials produced by the method of compression molding by more than 1.5 times compared to the brick with a traditional mass preparation.

  12. Development of fabrication technology for future fuel - Study on the defect structure and transport properties of doped U O{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Han Il; Hong, Kug Sun; Lee, Jong Ho; Kang, Sun Ho; Lee, Jung Gun [Seoul National University, Seoul (Korea, Republic of)

    1995-08-01

    The objectives of this project is the study on the defect structure and transport properties on nuclear material to secure the nuclear energy as the substitute source of power. Through this study, we can analyse the effect of dopant in nuclear material thoroughly and further we can establish the basis for the proper processing. And also we can verify the coulometric titration method as a very useful method to characterise the nuclear material. 27 refs., 2 tabs., 7 figs. (author)

  13. Analysis of defect structures in recrystallized amorphous layers of self-ion irradiated silicon by channeling and transmission electron microscopy measurements

    International Nuclear Information System (INIS)

    Pronko, P.P.; Rechtin, M.D.; Foti, G.; Csepregi, L.; Kennedy, E.F.; Mayer, J.W.

    1976-01-01

    The dominant defect structures in these reordered layers have been identified as twins whose dimensions change in size going from the surface to the interface. A high density of clustered defects is observed near the interface and is manifested by the presence of a heavy strain contrast in the electron micrograph image. Some fine polycrystallinity is also observed in the region of the interface between the regrown layer and the substrate. The 2 MeV 4 He channeling results indicate that, in this kind of defect arrangement, the standard analysis for reducing the channeling data cannot be applied. A more direct way to examine the depth dependence of the defect distribution by channeling is to follow the change in the minimum yield as a function of layer removal. The results obtained in this way show that the number of scattering centers (N/sub D//N/sub O/) is approximately constant in the first 3000 A and increases very fast near the interface. No tail in the scattering distribution is observed to penetrate the substrate when using the stripping procedure. This agrees generally with the TEM results

  14. Ancient Egyptian chronology and the astronomical orientation of pyramids

    Science.gov (United States)

    Spence, Kate

    2000-11-01

    The ancient Egyptian pyramids at Giza have never been accurately dated, although we know that they were built approximately around the middle of the third millennium BC. The chronologies of this period have been reconstructed from surviving lists of kings and the lengths of their reigns, but the lists are rare, seldom complete and contain known inconsistencies and errors. As a result, the existing chronologies for that period (the Old Kingdom) can be considered accurate only to about +/-100 years, a figure that radiocarbon dating cannot at present improve. Here I use trends in the orientation of Old Kingdom pyramids to demonstrate that the Egyptians aligned them to north by using the simultaneous transit of two circumpolar stars. Modelling the precession of these stars yields a date for the start of construction of the Great Pyramid that is accurate to +/-5 yr, thereby providing an anchor for the Old Kingdom chronologies.

  15. The Heeger & Bergen Pyramid Based Texture Synthesis Algorithm

    Directory of Open Access Journals (Sweden)

    Thibaud Briand

    2014-11-01

    Full Text Available This contribution deals with the Heeger-Bergen pyramid-based texture analysis/synthesis algorithm. It brings a detailed explanation of the original algorithm tested on many characteristic examples. Our analysis reproduces the original results, but also brings a minor improvement concerning non-periodic textures. Inspired by visual perception theories, Heeger and Bergen proposed to characterize a texture by its first-order statistics of both its color and its responses to multiscale and multi-orientation filters, namely the steerable pyramid. The Heeger-Bergen algorithm consists in the following procedure: starting from a white noise image, histogram matchings are performed to the noise alternatively in both the image domain and steerable pyramid domain, so that the corresponding histograms match the ones of the input texture.

  16. Pyramid Algorithm Framework for Real-Time Image Effects

    DEFF Research Database (Denmark)

    Sangüesa, Adriá Arbués; Ene, Andreea-Daniela; Jørgensen, Nicolai Krogh

    2016-01-01

    Pyramid methods are useful for certain image processing techniques due to their linear time complexity. Implementing them using compute shaders provides a basis for rendering image effects with reduced impact on performance compared to conventional methods. Although pyramid methods are used...... in the game industry, they are not easily accessible to all developers because many game engines do not include built-in support. We present a framework for a popular game engine that allows users to take advantage of pyramid methods for developing image effects. In order to evaluate the performance...... and to demonstrate the framework, a few image effects were implemented. These effects were compared to built-in effects of the same game engine. The results showed that the built-in image effects performed slightly better. The performance of our framework could potentially be improved through optimisation, mainly...

  17. Pyramidal cell-interneuron interactions underlie hippocampal ripple oscillations.

    Science.gov (United States)

    Stark, Eran; Roux, Lisa; Eichler, Ronny; Senzai, Yuta; Royer, Sebastien; Buzsáki, György

    2014-07-16

    High-frequency ripple oscillations, observed most prominently in the hippocampal CA1 pyramidal layer, are associated with memory consolidation. The cellular and network mechanisms underlying the generation, frequency control, and spatial coherence of the rhythm are poorly understood. Using multisite optogenetic manipulations in freely behaving rodents, we found that depolarization of a small group of nearby pyramidal cells was sufficient to induce high-frequency oscillations, whereas closed-loop silencing of pyramidal cells or activation of parvalbumin- (PV) or somatostatin-immunoreactive interneurons aborted spontaneously occurring ripples. Focal pharmacological blockade of GABAA receptors abolished ripples. Localized PV interneuron activation paced ensemble spiking, and simultaneous induction of high-frequency oscillations at multiple locations resulted in a temporally coherent pattern mediated by phase-locked interneuron spiking. These results constrain competing models of ripple generation and indicate that temporally precise local interactions between excitatory and inhibitory neurons support ripple generation in the intact hippocampus. Copyright © 2014 Elsevier Inc. All rights reserved.

  18. Hydrogen trapping by VC precipitates and structural defects in a high strength Fe–Mn–C steel studied by small-angle neutron scattering

    International Nuclear Information System (INIS)

    Malard, B.; Remy, B.; Scott, C.; Deschamps, A.; Chêne, J.; Dieudonné, T.; Mathon, M.H.

    2012-01-01

    Highlights: ► SANS was used to study the interaction between H and a Fe–Mn–C steel containing V. ► No interaction between H and V in solid solution has been detected. ► A reversible interaction between H and structural defects has been measured. ► 5 ppm wt. of H can be trapped in the VC nanoprecipitates. - Abstract: The trapping of hydrogen by VC precipitates and structural defects in high strength Fe–Mn–C steel was studied by small angle neutron scattering. No interaction between H and V in solid solution has been detected but a significant interaction between H and structural defects introduced by plastic deformation has been measured. This last effect was reversible upon outgassing of the H. Moreover a significant interaction between H and VC precipitates has been measured; 5 ppm wt. of H could be trapped in the precipitates. This is consistent with the homogeneous trapping of H within the precipitates rather than at the precipitate/matrix interface.

  19. Atomic structure of surface defects in alumina studied by dynamic force microscopy: strain-relief-, translation- and reflection-related boundaries, including their junctions

    International Nuclear Information System (INIS)

    Simon, G H; König, T; Heinke, L; Lichtenstein, L; Heyde, M; Freund, H-J

    2011-01-01

    We present an extensive atomic resolution frequency modulation dynamic force microscopy study of ultrathin aluminium oxide on a single crystalline NiAl(110) surface. One-dimensional surface defects produced by domain boundaries have been resolved. Images are presented for reflection domain boundaries (RDBs), four different types of antiphase domain boundaries, a nucleation-related translation domain boundary and also domain boundary junctions. New structures and aspects of the boundaries and their network are revealed and merged into a comprehensive picture of the defect arrangements. The alumina film also covers the substrate completely at the boundaries and their junctions and follows the structural building principles found in its unit cell. This encompasses square and rectangular groups of surface oxygen sites. The observed structural elements can be related to the electronic signature of the boundaries and therefore to the electronic defects associated with the boundaries. A coincidence site lattice predicted for the RDBs is in good agreement with experimental data. With Σ = 19 it can be considered to be of low-sigma type, which frequently coincides with special boundary properties. Images of asymmetric RDBs show points of good contact alternating with regions of nearly amorphous disorder in the oxygen sublattice. (paper)

  20. Variation in the defect structure of p-CdTe single crystals at the passage of the laser shock wave

    International Nuclear Information System (INIS)

    Baidullaeva, A.; Vlasenko, A.I.; Gorkovenko, B.L.; Lomovtsev, A.V.; Mozol', P.E.

    2000-01-01

    Variations in the minority-carrier lifetime, photoluminescence spectra, dark current and photocurrent temperature dependences of high-resistivity p-CdTe crystals under the action of the laser shock wave are investigated. It is shown that the variations in the aforementioned characteristics during the passage of the shock wave are defined by the generation of the nonequilibrium carriers from deep centers, and, after that, the variations are defined by the formation of intrinsic defects and their subsequent interaction with the defects existing in the initial crystals

  1. Discovering a Defect that Imposes a Limit to Mg Doping in p-Type GaN

    International Nuclear Information System (INIS)

    Liliental-Weber, Z.; Tomaszewicz, T.; Zakharov, D.; O'Keefe, M.A.

    2006-01-01

    Gallium nitride (GaN) is the III-V semiconductor used to produce blue light-emitting diodes (LEDs) and blue and ultraviolet solid-state lasers. To be useful in electronic devices, GaN must be doped with elements that function either as electron donors or as acceptors to turn it into either an n-type semiconductor or a p-type semiconductor. It has been found that GaN can easily be grown with n-conductivity, even up to large concentrations of donors--in the few 10 19 cm -3 range. However, p-doping, the doping of the structure with atoms that provide electron sinks or holes, is not well understood and remains extremely difficult. The only efficient p-type dopant is Mg, but it is found that the free hole concentration is limited to 2 x 10 18 cm -3 , even when Mg concentrations are pushed into the low 10 19 cm -3 range. This saturation effect could place a limit on further development of GaN based devices. Further increase of the Mg concentration, up to 1 x 10 20 cm -3 leads to a decrease of the free hole concentration and an increase in defects. While low- to medium-brightness GaN light-emitting diodes (LEDs) are remarkably tolerant of crystal defects, blue and UV GaN lasers are much less so. We used electron microscopy to investigate Mg doping in GaN. Our transmission electron microscopy (TEM) studies revealed the formation of different types of Mg-rich defects [1,2]. In particular, high-resolution TEM allowed us to characterize a completely new type of defect in Mg-rich GaN. We found that the type of defect depended strongly on crystal growth polarity. For crystals grown with N-polarity, planar defects are distributed at equal distances (20 unit cells of GaN); these defects can be described as inversion domains [1]. For growth with Ga-polarity, we found a different type of defect [2]. These defects turn out to be three-dimensional Mg-rich hexagonal pyramids (or trapezoids) with their base on the (0001) plane and their six walls formed on {1123} planes (Fig. 1a). In

  2. Space Station view of the Pyramids at Giza

    Science.gov (United States)

    2002-01-01

    One of the world's most famous archaeological sites has been photographed in amazing detail by the astronauts onboard Space Station Alpha. This image, taken 15 August, 2001, represents the greatest detail of the Giza plateau captured from a human-occupied spacecraft (approximate 7 m resolution). Afternoon sun casts shadows that help the eye make out the large pyramids of Khufu, Khafre and Menkaure. Sets of three smaller queens' pyramids can be seen to the east of the Pyramid of Khufu and south of the Pyramid of Menkaure. The light-colored causeway stretching from the Mortuary Temple at the Pyramid of Khafre to the Valley Temple near the Sphinx (arrow) can also be seen. Because it is not tall enough to cast a deep shadow, the Sphinx itself cannot readily be distinguished. Although some commercial satellites, such as IKONOS, have imaged the Pyramids at Giza in greater detail (1 m resolution), this image highlights the potential of the International Space Station as a remote sensing platform. A commercial digital camera without space modifications was used to obtain this picture. Similarly, a variety of remote sensing instruments developed for use on aircraft can potentially be used from the Space Station. Currently, all photographs of Earth taken by astronauts from the Space Shuttle and Space Station are released to the public for scientific and educational benefit and can be accessed on the World Wide Web through the NASA-JSC Gateway to Astronaut Photography of Earth (http://eol/jsc.nasa.gov/sseop). Image ISS003-ESC-5120 was provided by the Earth Sciences and Image Analysis Laboratory at Johnson Space Center (http://eol.jsc.nasa.gov).

  3. Understanding political radicalization: The two-pyramids model.

    Science.gov (United States)

    McCauley, Clark; Moskalenko, Sophia

    2017-04-01

    This article reviews some of the milestones of thinking about political radicalization, as scholars and security officials struggled after 9/11 to discern the precursors of terrorist violence. Recent criticism of the concept of radicalization has been recognized, leading to a 2-pyramids model that responds to the criticism by separating radicalization of opinion from radicalization of action. Security and research implications of the 2-pyramids model are briefly described, ending with a call for more attention to emotional experience in understanding both radicalization of opinion and radicalization of action. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  4. Prenatal detection of structural cardiac defects and presence of associated anomalies: a retrospective observational study of 1262 fetal echocardiograms.

    Science.gov (United States)

    Mone, Fionnuala; Walsh, Colin; Mulcahy, Cecelia; McMahon, Colin J; Farrell, Sinead; MacTiernan, Aoife; Segurado, Ricardo; Mahony, Rhona; Higgins, Shane; Carroll, Stephen; McParland, Peter; McAuliffe, Fionnuala M

    2015-06-01

    The aim of this study is to document the detection of fetal congenital heart defect (CHD) in relation to the following: (1) indication for referral, (2) chromosomal and (3) extracardiac abnormalities. All fetal echocardiograms performed in our institution from 2007 to 2011 were reviewed retrospectively. Indication for referral, cardiac diagnosis based on the World Health Organization International Classification of Diseases tenth revision criteria and the presence of chromosomal and extracardiac defects were recorded. Of 1262 echocardiograms, 287 (22.7%) had CHD. Abnormal anatomy scan in pregnancies originally considered to be at low risk of CHD was the best indicator for detecting CHD (91.2% of positive cardiac diagnoses), compared with other indications of family history (5.6%) or maternal medical disorder (3.1%). Congenital anomalies of the cardiac septa comprised the largest category (n = 89), within which atrioventricular septal defects were the most common anomaly (n = 36). Invasive prenatal testing was performed for 126 of 287 cases, of which 44% (n = 55) had a chromosomal abnormality. Of 232 fetuses without chromosomal abnormalities, 31% had an extracardiac defect (n = 76). Most CHDs occur in pregnancies regarded to be at low risk, highlighting the importance of a routine midtrimester fetal anatomy scan. Frequent association of fetal CHD and chromosomal and extracardiac pathology emphasises the importance of thorough evaluation of any fetus with CHD. © 2015 John Wiley & Sons, Ltd.

  5. Study of correlation between the structural defects and inhomogeneities of CDTE based radiation detectors used for medical imaging

    International Nuclear Information System (INIS)

    Buis, Camille

    2013-01-01

    In the present Ph.D. thesis, we investigate microstructural defects in a chlorine-doped cadmium telluride crystal (CdTe:Cl), to understand the relationship between defects and performance of CdTe-based radiation detectors. Characterization tools, such as diffraction topography and chemical etching, are used for bulk and surface investigations of the distribution of dislocations. Dislocations are arranged into walls. Most of them appear to cross the whole thickness of the sample. Very good correlation is observed between areas with variations of dark-current and photo-current, and positions of the dislocation walls revealed at the surface of the sample. Then spectroscopic analysis of these defects was performed at low temperatures. It highlighted that dislocation walls induce non-radiative recombination, but it didn't show any Y luminescence usually attributed to dislocations in the literature. Ion Beam Induced Current (IBIC) measurements were used to evaluate the influence of dislocation walls on charge carrier transport properties. This experiment shows that they reduce the mobility-lifetime product of the charge carriers. A very clear correlation was, in fact, established between the distribution of the dislocation network and the linear defects revealed by their lower CIE on the device. (author) [fr

  6. Study of the defect structures produced by heavy ions in dielectrics by means of small angle scattering

    International Nuclear Information System (INIS)

    Albrecht, D.J.

    1983-11-01

    The aim of the present thesis was to study the defects in dielectrics produced by fast ions. For this the small angle scattering was proved as suitable method. By the production by means of the ion beam of an accelerator the defects possess a pronounced preferential direction. In scattering experiments this system of scattering centers is distinguished by its unusually strong dependence of the sample orientation according to the primary beam. This property was studied, described, and illustrated by examples, and it could by shown that from this additional informations about the scattering defects can be derived. For the first time nuclear tracks were detected by means of small angle neutron scattering. It could be shown that here the same results are obtained as by small angle X-ray scattering. The measured intensity distributions could be assigned to a mathematical model description which gives form, width, and density of the tracks in the position space. On the base of this cylinder model computer codes were established which simulate the scattering experiment regarding the main influences and calculate the expected theoretical intensity distribution. The agreement between calculated and measured scattering distributions proves the validity of the model. The parameters determined by this model, maximal change of density in the track, defect length, radial dilatation, distance of the narrowings and there depth were determined. For the main quantities, radial dilatation and maximal change of densities a simple description of the energy dependence could be given via the energy loss. (orig./HSI) [de

  7. Reproductive experience modified dendritic spines on cortical pyramidal neurons to enhance sensory perception and spatial learning in rats.

    Science.gov (United States)

    Chen, Jeng-Rung; Lim, Seh Hong; Chung, Sin-Cun; Lee, Yee-Fun; Wang, Yueh-Jan; Tseng, Guo-Fang; Wang, Tsyr-Jiuan

    2017-01-27

    Behavioral adaptations during motherhood are aimed at increasing reproductive success. Alterations of hormones during motherhood could trigger brain morphological changes to underlie behavioral alterations. Here we investigated whether motherhood changes a rat's sensory perception and spatial memory in conjunction with cortical neuronal structural changes. Female rats of different statuses, including virgin, pregnant, lactating, and primiparous rats were studied. Behavioral test showed that the lactating rats were most sensitive to heat, while rats with motherhood and reproduction experience outperformed virgin rats in a water maze task. By intracellular dye injection and computer-assisted 3-dimensional reconstruction, the dendritic arbors and spines of the layer III and V pyramidal neurons of the somatosensory cortex and CA1 hippocampal pyramidal neurons were revealed for closer analysis. The results showed that motherhood and reproductive experience increased dendritic spines but not arbors or the lengths of the layer III and V pyramidal neurons of the somatosensory cortex and CA1 hippocampal pyramidal neurons. In addition, lactating rats had a higher incidence of spines than pregnant or primiparous rats. The increase of dendritic spines was coupled with increased expression of the glutamatergic postsynaptic marker protein (PSD-95), especially in lactating rats. On the basis of the present results, it is concluded that motherhood enhanced rat sensory perception and spatial memory and was accompanied by increases in dendritic spines on output neurons of the somatosensory cortex and CA1 hippocampus. The effect was sustained for at least 6 weeks after the weaning of the pups.

  8. Crystal defects and related stress in Y2O3 thin films: Origin, modeling, and consequence on the stability of the C-type structure

    International Nuclear Information System (INIS)

    Lacroix, Bertrand; Paumier, Fabien; Gaboriaud, Rolly J.

    2011-01-01

    We study the impact that the crystal defects have on the C-type structure of rare earth sesquioxide thin films grown by ion-beam sputtering, through the example of Y 2 O 3 . By monitoring the energy of the argon beam used in the sputter deposition process (between 600 and 1200 eV), we show that it is possible to control the microstructure (defects concentration, stress state and phase) in the oxide layer. Two main types of defects, ascribed to the 'atomic peening effect', are evidenced by high-resolution transmission electron microscopy, Rutherford backscattering spectroscopy, and nuclear reaction analysis experiments: anti-Frenkel pairs, leading to a disorder on the oxygen-vacancy network, and oxygen-vacancy dislocations loops, to accommodate the strong nonstoichiometry. From a macroscopic measurement of the residual stresses in the as-deposited and the annealed layers, through x-ray diffraction and the sin 2 Ψ method, we have modeled the related stress state using an enhanced triaxial stress model. In the as-grown films, we evidence the coexistence of a biaxial and a hydrostatic stress, due to inclusions of atomic size defects. Quantitative information of the concentration and the nature of each type of defect (size effect) have also been determined, in good agreement with experiments. Interestingly, in the most energetic growth conditions corresponding to the highest degree of disorder on the oxygen-vacancy network and to the highest stress field in the film, we demonstrate that it is possible to stabilize an unexpected and metastable non equilibrium fluorite-like phase (X-type).

  9. Defect and phase stability of solid solutions of Mg2X with an antifluorite structure: An ab initio study

    International Nuclear Information System (INIS)

    Viennois, Romain; Jund, Philippe; Colinet, Catherine; Tédenac, Jean-Claude

    2012-01-01

    First principles calculations are done for Mg 2 X (X=Si, Ge or Sn) antifluorite compounds and their solid solutions in order to investigate their pseudo-binary phase diagram. The formation energies of the end-member compounds agree qualitatively with the experiments. For X=Si and Ge, there is a complete solubility, but we observe a miscibility gap in the pseudo-binary phase diagram Mg 2 Si–Mg 2 Sn. This agrees with the most recent experiments and phase diagram assessments. Calculated electronic properties of Mg 2 Si 1−x Sn x alloys qualitatively agree with experiments and in particular the energy bandgap decreases when Si is substituted by Sn. Supercell calculations are also done in order to determine the most stable defects and the doping induced by these defects in the three end-member compounds. We find that the intrinsic n-doping in pure Mg 2 Si can be attributed to the presence of magnesium atoms in interstitial positions. In Mg 2 Ge and Mg 2 Sn, since other defects are stable, they can be also of p-type. - Graphical abstract: Evidence of a miscibility gap from the plot of the formation energy vs x Si (silicon content) for the solid solutions Mg 2 Si–Mg 2 Sn. Highlights: ► First-principles study of the stability of Mg 2 Si–Mg 2 X alloys (X=Ge or Sn) and their defects. ► Mg 2 Si–Mg 2 Ge alloys form a complete series of solid solutions. ► Miscibility gap is found in Mg 2 Si–Mg 2 Sn alloys. ► Interstitial defects are more stable in Mg 2 Si and induce n-doping.

  10. Effect of thermal treatment on the density of radiation-induced defects in dielectrics and on the semiconductor surface of silicon MDS structures

    International Nuclear Information System (INIS)

    Daliev, Kh.S.; Lebedev, A.A.; Ehkke, V.; 3425000DD)

    1987-01-01

    Isochronous annealing of radiation defects formed under MIS structure irradiation by γ-quanta at the presence of shift stress on a metal electrode is studied. Complex measurements of non-stationary capacitance spectroscopy and volt-farad characteristics (VFC) have shown that a built-in charge and volumetric states (VS) of the dielectric are annealed at 250 deg C, fast surface states (SS) - at 350 deg C, and the characteristic radiation defect in the Si-SiO 2 transition layer is completely annealed only at 400 deg C. Additional VS and SS occurring in the structures at positive shift on the metal electrode under radiation are annealed at 120 deg C, the kinetics of defect annealing at higher temperatures is independent from shift polarity. SS density calculated by VFC is determined in reality by recharging not only SS but some VS of the dielectric in the range of width of the order of 3.5 nm from the surface of the semiconductor

  11. Defects and defect processes in nonmetallic solids

    CERN Document Server

    Hayes, W

    2004-01-01

    This extensive survey covers defects in nonmetals, emphasizing point defects and point-defect processes. It encompasses electronic, vibrational, and optical properties of defective solids, plus dislocations and grain boundaries. 1985 edition.

  12. Logical thinking in the pyramidal schema of concepts the logical and mathematical elements

    CERN Document Server

    Geldsetzer, Lutz

    2014-01-01

    This book proposes a new way of formalizing in logic and mathematics - a "pyramidal graph system," devised by the author and based on Porphyrian trees and modern concepts of classification, in both of which pyramids act as the organizing schema.

  13. Study of the oxygen and substrate bias effects on the defect structure of reactive sputter-deposited SnOx films

    International Nuclear Information System (INIS)

    Misheva, M.; Nancheva, N.; Docheva, P.; Hadjijska, P.; Djourelov, N.; Elenkov, D.

    1999-01-01

    The effects of oxygen and substrate bias on the defect structure of reactive sputter-deposited SnOx films were investigated. Samples were analysed using transmission electron microscopy (TEM), transmission electron diffraction (TED), X-ray diffraction (XRD) and positron annihilation spectroscopy (PAS). The oxygen played an important role in the film growth and surface morphology. TEM, TED and XRD showed that increasing of the oxygen partial pressure leads to the formation of films with different crystal phases. The void sizes also depended on oxygen partial pressure. The positron lifetimes and their relative intensities depended on the void concentration, the partial annealing of the vacancies and oxidation of SnO to SnOx. This investigation also showed that the mechanical strength of the films obtained at negative substrate bias is higher and the concentration of vacancy defects is smaller, than in the films, prepared without substrate bias. (author)

  14. Radon measurements in the interior of the great pyramid

    Energy Technology Data Exchange (ETDEWEB)

    Kenawy, M A; Morsy, A A [Ain Shams Univ., Cairo (Egypt). College for Girls

    1991-01-01

    Radon concentration measurements were made in the interior of the great pyramid of ''Cheops'' at Giza. Measurements were carried out using CR-39 as a solid state nuclear track detector. The CR-39 sheets were placed inside the Queen's and King's chambers and along the ascending corridor leading to them. An evaluation of the radon concentration is presented and discussed. (author).

  15. The Sphinx and the Pyramids at Giza. Educational Packet.

    Science.gov (United States)

    Gagliano, Sara; Rapport, Wendy

    This packet of materials was created to accompany the exhibit "The Sphinx and the Pyramids: 100 Years of American Archaeology at Giza" at the Semitic Museum of Harvard University. The lessons and teacher's guide focus on the following: (1) "The Mystery of the Secret Tomb" where students take on the role of an archaeologist by…

  16. a pyramid algorithm for the haar discrete wavelet packet transform

    African Journals Online (AJOL)

    PROF EKWUEME

    computer-aided signal processing of non-stationary signals, this paper develops a pyramid algorithm for the discrete wavelet packet ... Edith T. Luhanga, School of Computational and Communication Sciences and Engineering, Nelson Mandela African. Institute of ..... Mathematics, Washington University. 134. EDITH T.

  17. Surgical anatomy of the pyramidal lobe and its significance in ...

    African Journals Online (AJOL)

    33:35-37. 10. Harjeet A, Shani D, Jit I, Aggarwal AK. Shape, measurements and weight of the thyroid gland in northwest Indians. Surg Radiol Anat 2004;26:91-95. TABLE III. INVOLVEMENT OF THE PYRAMIDAL LOBE IN VARIOUS THYROID ...

  18. Nano-pyramid arrays for nano-particle trapping

    NARCIS (Netherlands)

    Sun, Xingwu; Veltkamp, Henk-Willem; Berenschot, Johan W.; Gardeniers, Johannes G.E.; Tas, Niels Roelof

    2016-01-01

    Abstract In this paper we present the drastic miniaturization of nano-wire pyramids fabricated by corner lithography. A particle trapping device was fabricated in a well-defined and symmetrical array. The entrance and exit hole-size can be tuned by adjusting fabrication parameters. We describe here

  19. Exciton binding energy in a pyramidal quantum dot

    Science.gov (United States)

    Anitha, A.; Arulmozhi, M.

    2018-05-01

    The effects of spatially dependent effective mass, non-parabolicity of the conduction band and dielectric screening function on exciton binding energy in a pyramid-shaped quantum dot of GaAs have been investigated by variational method as a function of base width of the pyramid. We have assumed that the pyramid has a square base with area a× a and height of the pyramid H=a/2. The trial wave function of the exciton has been chosen according to the even mirror boundary condition, i.e. the wave function of the exciton at the boundary could be non-zero. The results show that (i) the non-parabolicity of the conduction band affects the light hole (lh) and heavy hole (hh) excitons to be more bound than that with parabolicity of the conduction band, (ii) the dielectric screening function (DSF) affects the lh and hh excitons to be more bound than that without the DSF and (iii) the spatially dependent effective mass (SDEM) affects the lh and hh excitons to be less bound than that without the SDEM. The combined effects of DSF and SDEM on exciton binding energy have also been calculated. The results are compared with those available in the literature.

  20. Marker-assisted pyramiding of Thinopyrum-derived leaf rust ...

    Indian Academy of Sciences (India)

    Annual Meetings · Mid Year Meetings · Discussion Meetings · Public Lectures · Lecture Workshops · Refresher Courses · Symposia · Live Streaming. Home; Journals; Journal of Genetics; Volume 96; Issue 6. Marker-assisted pyramiding of Thinopyrum-derived leaf rust resistance genes Lr19 and Lr24 in bread wheat variety ...

  1. Using the Pyramid Approach to Teaching Marketing Research.

    Science.gov (United States)

    Peltier, James W.; Westfall, John; Ainscough, Thomas L.

    2001-01-01

    Underscores the need for teaching marketing research skills at the secondary level and shows how marketing research fits into marketing education. Provides an example of how to use the pyramid approach to research, which involves review of secondary sources, key informant interviews, focus groups, and quantitative research. (Author/JOW)

  2. Surgical anatomy of the pyramidal lobe and its significance in ...

    African Journals Online (AJOL)

    In diffuse thyroid diseases, the lobes were always pathologically involved and significantly longer. Conclusion. Since the pyramidal lobe is a normal component of the thyroid gland, of varying position and size, with pathological changes in benign and malignant diseases, it should always be examined during thyroid surgery ...

  3. Setting aside transactions from pyramid schemes as impeachable ...

    African Journals Online (AJOL)

    These schemes, which are often referred to as pyramid or Ponzi schemes, are unsustainable operations and give rise to problems in the law of insolvency. Investors in these schemes are often left empty-handed upon the scheme's eventual collapse and insolvency. Investors who received pay-outs from the scheme find ...

  4. Angles of Elevation of the Pyramids of Egypt.

    Science.gov (United States)

    Smith, Arthur F.

    1982-01-01

    The nature and history of the construction of pyramids in Egypt is detailed. It is noted that one can only theorize about why the Egyptians used particular angles of elevation. It is thought, perhaps, that new clues will provide a clear solution to this mystery as additional artifacts and hieroglyphics are discovered. (MP)

  5. Radon measurements in the interior of the great pyramid

    International Nuclear Information System (INIS)

    Kenawy, M.A.; Morsy, A.A.

    1991-01-01

    Radon concentration measurements were made in the interior of the great pyramid of ''Cheops'' at Giza. Measurements were carried out using CR-39 as a solid state nuclear track detector. The CR-39 sheets were placed inside the Queen's and King's chambers and along the ascending corridor leading to them. An evaluation of the radon concentration is presented and discussed. (author)

  6. Wooden's pyramid: building a hierarchy of skills for successful communication.

    Science.gov (United States)

    Epner, Daniel E; Baile, Walter F

    2011-01-01

    John Wooden, the legendary college basketball coach, created the "Pyramid of Success", which he constructed from 14 timeless character traits and interpersonal skills that are critical to competitive greatness. Wooden's pyramid is a powerful symbol that he and others have used for several decades as an educational tool to promote leadership and teamwork. This article proposes the "Pyramid of Relational Excellence (PRE)", patterned after Wooden's pyramid, as a mnemonic-based educational symbol for communication skills training. Literature review, personal reflection. The PRE is constructed of four tiers with a total of 12 building blocks, with each successive tier built upon the one beneath it. The building blocks represent fundamental elements that are known to be critical to successful communication. The PRE is process oriented rather than task oriented and focuses exclusively on the face-to-face encounter. It therefore complements established communications curricula, such as the UK communication wheel and others, which are more comprehensive and task oriented. The PRE is constructed of timeless, fundamental principles. It is therefore particularly well suited for training medical students and residents.

  7. Nanopore formation on Au coated pyramid under electron beam irradiations (plasmonic nanopore on pyramid

    Directory of Open Access Journals (Sweden)

    Seong Soo Choi

    2016-03-01

    Full Text Available There have been tremendous interests about the single molecule analysis using a sold-state nanopore. The solid-state nanopore can be fabricated either by drilling technique, or diffusion technique by using electron beam irradiations. The solid-state SiN nanopore device with electrical detection technique recently fabricated, however, the solid-state Au nanopore with optical detection technique can be better utilized as the next generation single molecule sensor. In this report, the nanometer size openings with its size less than 10 nm on the diffused membrane on the 200 nm Au pyramid were fabricated by using field emission scanning electron microscopy (FESEM electron beam irradiations, transmission electron microscopy (TEM, etc. After the sample was being kept under a room environment for several months, several Au (111 clusters with ~6 nm diameter formed via Ostwald ripening are observed using a high resolution TEM imaging. The nanopore with Au nanoclusters on the diffused membrane can be utilized as an optical nanopore device. Keywords: Electron beam irradiation, Surface diffusion, Carbon contamination, Au cluster, Ostwald ripening

  8. Analysis of Manufacturing-Induced Defects and Structural Deformations in Lithium-Ion Batteries Using Computed Tomography

    OpenAIRE

    Yi Wu; Saurabh Saxena; Yinjiao Xing; Youren Wang; Chuan Li; Winco K. C. Yung; Michael Pecht

    2018-01-01

    Premature battery drain, swelling and fires/explosions in lithium-ion batteries have caused wide-scale customer concerns, product recalls, and huge financial losses in a wide range of products including smartphones, laptops, e-cigarettes, hoverboards, cars, and commercial aircraft. Most of these problems are caused by defects which are difficult to detect using conventional nondestructive electrical methods and disassembly-based destructive analysis. This paper develops an effective computed ...

  9. Effective lifetime of minority carriers in black silicon nano-textured by cones and pyramids

    DEFF Research Database (Denmark)

    Onyshchenko, V.F.; Karachevtseva, L.A.; Lytvynenko, O.O.

    2017-01-01

    We calculated the dependence of effective lifetime of minority carriers in black silicon nano-textured by cones and pyramids on the diameter of the cone base, the side of the pyramid base, the height of cone and pyramid. The numerical calculation shows that n-type polished plate of single crystal...

  10. Characterization of a defective PbWO4 crystal cut along the a-c crystallographic plane: structural assessment and a novel photoelastic stress analysis

    Science.gov (United States)

    Montalto, L.; Natali, P. P.; Daví, F.; Mengucci., P.; Paone, N.; Rinaldi, D.

    2017-12-01

    Among scintillators, the PWO is one of the most widely used, for instance in CMS calorimeter at CERN and PANDA project. Crystallographic structure and chemical composition as well as residual stress condition, are indicators of homogeneity and good quality of the crystal. In this paper, structural characterization of a defective PbWO4 (PWO) crystal has been performed by X-ray Diffraction (XRD), Energy Dispersive Spectroscopy (EDS) and Photoelasticity in the unusual (a, c) crystallographic plane. XRD and EDS analysis have been used to investigate crystallographic orientation and chemical composition, while stress distribution, which indicates macroscopic inhomogeneities and defects, has been obtained by photoelastic approaches, in Conoscopic and Sphenoscopic configuration. Since the sample is cut along the (a, c) crystallographic plane, a new method is proposed for the interpretation of the fringe pattern. The structural analysis has detected odds from the nominal lattice dimension, which can be attributed to the strong presence of Pb and W. A strong inhomogeneity over the crystal sample has been revealed by the photoelastic inspection. The results give reliability to the proposed procedure which is exploitable in crystals with other structures.

  11. Augmentation of failed human vertebrae with critical un-contained lytic defect restores their structural competence under functional loading: An experimental study.

    Science.gov (United States)

    Alkalay, Ron N; von Stechow, Dietrich; Hackney, David B

    2015-07-01

    Lytic spinal lesions reduce vertebral strength and may result in their fracture. Vertebral augmentation is employed clinically to provide mechanical stability and pain relief for vertebrae with lytic lesions. However, little is known about its efficacy in strengthening fractured vertebrae containing lytic metastasis. Eighteen unembalmed human lumbar vertebrae, having simulated uncontained lytic defects and tested to failure in a prior study, were augmented using a transpedicular approach and re-tested to failure using a wedge fracture model. Axial and moment based strength and stiffness parameters were used to quantify the effect of augmentation on the structural response of the failed vertebrae. Effects of cement volume, bone mineral density and vertebral geometry on the change in structural response were investigated. Augmentation increased the failed lytic vertebral strength [compression: 85% (Paugmentation is effective in bolstering the failed lytic vertebrae compressive and axial structural competence, showing strength estimates up to 50-90% of historical values of osteoporotic vertebrae without lytic defects. This modest increase suggests that lytic vertebrae undergo a high degree of structural damage at failure, with strength only partially restored by vertebral augmentation. The positive effect of cement volume is self-limiting due to extravasation. Copyright © 2015. Published by Elsevier Ltd.

  12. Computer simulation of defect cluster

    Energy Technology Data Exchange (ETDEWEB)

    Kuramoto, Eiichi [Kyushu Univ., Kasuga, Fukuoka (Japan). Research Inst. for Applied Mechanics

    1996-04-01

    In order to elucidate individual element process of various defects and defect clusters of used materials under irradiation environments, interatomic potential with reliability was investigated. And for comparison with experimental results, it is often required to adopt the temperature effect and to investigate in details mechanism of one dimensional motion of micro conversion loop and so forth using the molecular dynamic (MD) method. Furthermore, temperature effect is also supposed for stable structure of defects and defect clusters, and many problems relating to alloy element are also remained. And, simulation on photon life at the defects and defect clusters thought to be important under comparison with equipment can also be supposed an improvement of effectiveness due to relation to theses products. In this paper, some topics in such flow was extracted to explain them. In particular, future important problems will be potential preparation of alloy, structure, dynamic behavior and limited temperature of intralattice atomic cluster. (G.K.)

  13. Orange-red emitting Gd2Zr2O7:Sm3+: Structure-property correlation, optical properties and defect spectroscopy

    Science.gov (United States)

    Gupta, Santosh K.; Reghukumar, C.; Sudarshan, K.; Ghosh, P. S.; Pathak, Nimai; Kadam, R. M.

    2018-05-01

    Local structure analysis of dopant ion, understanding host to dopant energy transfer dynamics and defects characterization in a doped material which plays an important role in the designing a highly efficient opto-electronic material. In this connection a new Sm3+ doped Gd2Zr2O7 pyrochlore material was synthesized using gel-combustion technique and was characterized systematically using X-ray diffraction (XRD), time resolved photoluminescence spectroscopy (TRPLS), positron annihilation lifetime spectroscopy (PALS) and density functional theory (DFT) based ab-initio calculation. Based on DFT site selective energetics calculation and luminescence decay measurement, it was observed that the Sm3+ was distributed at both Gd3+ and Zr4+ site with higher Sm3+ fraction at the Gd3+ site. PALS was used to probe the presence of defects in the phosphor. In this work intense orange-red emission is realized through manipulating the energy transfer from host defect emission (oxygen vacancies) to Sm3+ which allows color emission from green in undoped to orange-red in doped samples. Effect of dopant concentration and annealing temperature was probed using TRPLS and PALS. These all information is highly important for researcher looking to achieve pyrochlore based phosphor materials with high quantum yield.

  14. The Prediction of Mental Quality of Life Based on Defectiveness/Shame Schema with Mediating Role of Emotional Intelligence and Coping Strategies by Means of Structural Equations Modeling

    Directory of Open Access Journals (Sweden)

    S. Dehghani

    2014-06-01

    Full Text Available Early maladaptive schema is assumed to be a disrupting factor for quality of life. Yet, the mechanism of this vulnerability is not well known. The purpose of this study was to investigate the characteristic of emotional intelligence and coping strategy with stress as a mediator between early maladaptive defectiveness/ shame and mental quality of life. Participants were 245 men and women in Isfahan who were selected as the sample by availability sampling method. They completed the Petrides and Furnham's Trait Emotional Intelligence Questionnaire-Short Form (TEIQue-SF, Coping Inventory for stressful situation (CISS and WHO Quality of Life-BREF (WHOQOL-BREF and Young Schema Questionnaire-Short Form (YSQ-SF. Data was analyzed by means of structural equation modeling. The results indicated that the suggested model of study needs modification and only emotional intelligence was the mediator. Standard path coefficient of defectiveness/shame schema to emotional intelligence was -0.55 and emotional intelligence to problem focused coping, emotion focused coping and mental quality of life were 0.49, -0.59 and 0.78 (p<0.05. Based on results, emotional intelligence training can improve mental quality of life and coping strategies in people who have early defectiveness/shame maladaptive schema.

  15. Topological defects in extended inflation

    International Nuclear Information System (INIS)

    Copeland, E.J.; Kolb, E.W.; Chicago Univ., IL; Liddle, A.R.

    1990-04-01

    We consider the production of topological defects, especially cosmic strings, in extended inflation models. In extended inflation, the Universe passes through a first-order phase transition via bubble percolation, which naturally allows defects to form at the end of inflation. The correlation length, which determines the number density of the defects, is related to the mean size of bubbles when they collide. This mechanism allows a natural combination of inflation and large-scale structure via cosmic strings. 18 refs

  16. Topological defects in extended inflation

    International Nuclear Information System (INIS)

    Copeland, E.J.; Kolb, E.W.; Liddle, A.R.

    1990-01-01

    We consider the production of topological defects, especially cosmic strings, in extended-inflation models. In extended inflation, the Universe passes through a first-order phase transition via bubble percolation, which naturally allows defects to form at the end of inflation. The correlation length, which determines the number density of the defects, is related to the mean size of the bubbles when they collide. This mechanism allows a natural combination of inflation and large-scale structure via cosmic strings

  17. A study on structure defects in irradiated lithium fluoride (thermal neutrons); Etude des imperfections de structure du fluorure de lithium irradie (neutrons thermiques)

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, M

    1958-06-19

    A study was made of the behavior of atomic defects, vacancies and interstitials, generated from the Li{sup 6}(n,{alpha})H{sup 3} reaction in Lip crystals. Defects appear as cavities and platelets around ten angstrom in size and increase both with neutron dose and annealing temperature. For longer irradiations, metallic lithium precipitates out, in epitaxy with LiF lattice, and later, lithium salts appear due to the penetration of atmospheric gases through the cracks present in the damaged crystal. Various x-ray experiments followed the formation and evolution of these imperfections when their atomic concentration reached 10{sup -4}. (author)

  18. Defect attributed variations of the photoconductivity and photoluminescence in the HVPE and MOCVD as-grown and irradiated GaN structures

    International Nuclear Information System (INIS)

    Gaubas, E.; Pobedinskas, P.; Vaitkus, J.; Uleckas, A.; Zukauskas, A.; Blue, A.; Rahman, M.; Smith, K.M.; Aujol, E.; Beaumont, B.; Faurie, J.-P.; Gibart, P.

    2005-01-01

    The effect of native and radiation induced defects on the photoconductivity transients and photoluminescence spectra have been examined in GaN epitaxial layers of 2.5 and 12μm thickness grown on bulk n-GaN/sapphire substrates by metal-organic chemical vapor deposition (MOCVD). For comparison, free-standing GaN as-grown samples of 500μm thickness, fabricated by hydride vapor phase epitaxy (HVPE), were investigated. Manifestation of defects induced by 10-keV X-ray irradiation with the dose of 600Mrad and 100-keV neutrons with the fluences of 5x10 14 and 10 16 cm -2 as well as of 24GeV/c protons with fluence 10 16 cm -2 have been revealed through contact photoconductivity and microwave absorption transients. The amplitude of the initial photoconductivity decay is significantly reduced by the native and radiation defects density. Synchronous decrease of the steady-state PL intensity of yellow, blue and ultraviolet bands peaked at 2.18, 2.85, and 3.42eV, respectively, with density of radiation-induced defects is observed. The decrease of the PL intensity is accompanied by an increase of asymptotic decay lifetime in the photoconductivity transients, which is due to excess-carrier multi-trapping. The decay fits the stretched exponent approximation exp[-(t/τ) α ] with the different factors α in as-grown material (α∼0.7) and irradiated samples (α∼0.3). The fracton dimension d s of disordered structure changes from 4.7 to 0.86 for as-grown and irradiated material, respectively, and it implies the percolative carrier motion on an infinite cluster of dislocations net in the as-grown material and cluster fragmentation into finite fractons after irradiations

  19. Evolution of Defect Structures and Deep Subgap States during Annealing of Amorphous In-Ga-Zn Oxide for Thin-Film Transistors

    Science.gov (United States)

    Jia, Junjun; Suko, Ayaka; Shigesato, Yuzo; Okajima, Toshihiro; Inoue, Keiko; Hosomi, Hiroyuki

    2018-01-01

    We investigate the evolution behavior of defect structures and the subgap states in In-Ga-Zn oxide (IGZO) films with increasing postannealing temperature by means of extended x-ray absorption fine-structure (EXAFS) measurements, positron annihilation lifetime spectroscopy (PALS), and cathodoluminescence (CL) spectroscopy, aiming to understand the relationship between defect structures and subgap states. EXAFS measurements reveal the varied oxygen coordination numbers around cations during postannealing and confirm two types of point defects, namely, excess oxygen around Ga atoms and oxygen deficiency around In and/or Zn atoms. PALS suggests the existence of cation-vacancy (VM )-related clusters with neutral or negative charge in both amorphous and polycrystalline IGZO films. CL spectra show a main emission band at approximately 1.85 eV for IGZO films, and a distinct shoulder located at about 2.15 eV for IGZO films postannealed above 600 °C . These two emission bands are assigned to a recombination between the electrons in the conduction band and/or in the shallow donor levels near the conduction band and the acceptors trapped above the valence-band maximum. The shallow donors are attributed to the oxygen deficiency, and the acceptors are thought to possibly arise from the excess oxygen or the VM-related clusters. These results open up an alternative route for understanding the device instability of amorphous IGZO-based thin-film transistors, especially the presence of the neutral or negatively charged VM-related clusters in amorphous IGZO films.

  20. A study on radiation energy of Pyramidal shape 1- Effect of housing within a Pyramid model on cancer growth and some blood parameters of mice

    International Nuclear Information System (INIS)

    El-Abiad, N.M.; Lotfi, S.A.; El Hadary, A.A.; Nagi, G.A.

    2010-01-01

    A study of solid tumor growth retardation by impaling the pyramid energy radiation in a pyramidal model shape was carried out. The great Pyramid of Egypt has evoked a keen interest since 1920, both for its architectural, marvel and mystical significance. Its strange thing (via shaping of razers, longer shelf life of vegetables, alerted states of consciousnesses, sleeping in hum and, wound healing). Power energy radiations are said to occur within a pyramid constructed in the exact geometric properties of Giza pyramid. The effect of housing in two different pyramidal shapes on cancer growth and some blood physiological indices in mice infected with cancer were observed. The results obtained that housing in pyramid shape cage significantly reduced the development of cancer, significant increase in liver enzymes activity and α feto proteins, however, no effect was observed in levels of thyroid hormones concentration when compared with their matched value in ordinary 2 inverted pyramid cages. It could be concluded that the radiation energy of pyramidal shapes might improve certain biochemical and physiological indices leading to tumor growth retardation

  1. Progressive Structural Defects in Canine Centronuclear Myopathy Indicate a Role for HACD1 in Maintaining Skeletal Muscle Membrane Systems.

    Science.gov (United States)

    Walmsley, Gemma L; Blot, Stéphane; Venner, Kerrie; Sewry, Caroline; Laporte, Jocelyn; Blondelle, Jordan; Barthélémy, Inès; Maurer, Marie; Blanchard-Gutton, Nicolas; Pilot-Storck, Fanny; Tiret, Laurent; Piercy, Richard J

    2017-02-01

    Mutations in HACD1/PTPLA cause recessive congenital myopathies in humans and dogs. Hydroxyacyl-coA dehydratases are required for elongation of very long chain fatty acids, and HACD1 has a role in early myogenesis, but the functions of this striated muscle-specific enzyme in more differentiated skeletal muscle remain unknown. Canine HACD1 deficiency is histopathologically classified as a centronuclear myopathy (CNM). We investigated the hypothesis that muscle from HACD1-deficient dogs has membrane abnormalities in common with CNMs with different genetic causes. We found progressive changes in tubuloreticular and sarcolemmal membranes and mislocalized triads and mitochondria in skeletal muscle from animals deficient in HACD1. Furthermore, comparable membranous abnormalities in cultured HACD1-deficient myotubes provide additional evidence that these defects are a primary consequence of altered HACD1 expression. Our novel findings, including T-tubule dilatation and disorganization, associated with defects in this additional CNM-associated gene provide a definitive pathophysiologic link with these disorders, confirm that dogs deficient in HACD1 are relevant models, and strengthen the evidence for a unifying pathogenesis in CNMs via defective membrane trafficking and excitation-contraction coupling in muscle. These results build on previous work by determining further functional roles of HACD1 in muscle and provide new insight into the pathology and pathogenetic mechanisms of HACD1 CNM. Consequently, alterations in membrane properties associated with HACD1 mutations should be investigated in humans with related phenotypes. Copyright © 2017 American Society for Investigative Pathology. Published by Elsevier Inc. All rights reserved.

  2. Structural defects and recombination behavior of excited carriers in Cu(In,Ga)Se{sub 2} solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J.; Du, H. W.; Li, Y.; Gao, M.; Wan, Y. Z.; Xu, F. [SHU-SolarE R& D Lab, Department of Physics, Shanghai University, Shanghai, 200444 (China); Ma, Z. Q., E-mail: zqma@shu.edu.cn [SHU-SolarE R& D Lab, Department of Physics, Shanghai University, Shanghai, 200444 (China); Instrumental Analysis & Research Center, Shanghai University, Shanghai, 200444 (China)

    2016-08-15

    The carriers’ behavior in neutral region (NTR) and space charged region (SCR) of Cu(In,Ga)Se{sub 2} thin film based solar cells has been investigated by temperature dependent photoluminescence (PL-T), electroluminescence (EL-T) and current-voltage (IV-T) from 10 to 300 K. PL-T spectra show that three kinds of defects, namely V{sub Se}, In{sub Cu} and (In{sub Cu}+V{sub Cu}), are localized within the band gap of NTR and SCR of CIGS layer, corresponding to the energy levels of E{sub C}-0.08, E{sub C}-0.20 and E{sub C}-0.25 eV, respectively. The In{sub Cu} and (In{sub Cu}+V{sub Cu}) deep level defects are non-radiative recombination centers at room temperature. The IV-T and EL-T analysis reveals that the injection modes of electrons from ZnO conduction band into Cu(In,Ga)Se{sub 2} layer are tunneling, thermally-excited tunneling and thermionic emission under 10-40, 60-160, and 180-300 K, respectively. At 10-160 K, the electrons tunnel into (In{sub Cu}+V{sub Cu}) and V{sub se} defect levels in band gap of SCR and the drifting is involved in the emission bands at 0.96 and 1.07 eV, which is the direct evidence for a tunneling assisted recombination. At 180-300 K, the electrons are directly injected into the Cu(In,Ga)Se{sub 2} conduction band, and the emission of 1.13 eV are ascribed to the transitions from the conduction band to the valence band.

  3. Computer modelling of defect structure and rare earth doping in LiCaAlF sub 6 and LiSrAlF sub 6

    CERN Document Server

    Amaral, J B; Valerio, M E G; Jackson, R A

    2003-01-01

    This paper describes a computational study of the mixed metal fluorides LiCaAlF sub 6 and LiSrAlF sub 6 , which have potential technological applications when doped with a range of elements, especially those from the rare earth series. Potentials are derived to represent the structure and properties of the undoped materials, then defect properties are calculated, and finally solution energies for rare earth elements are calculated, enabling preferred dopant sites and charge compensation mechanisms to be predicted.

  4. Using an equation based on flow stress to estimate structural integrity of annealed Type 304 stainless steel plate and pipes containing surface defects

    International Nuclear Information System (INIS)

    Reuter, W.G.; Place, T.A.

    1981-01-01

    An accurate assessment of the influence of defects on structural component integrity is needed. Generally accepted analytical techniques are not available for the very ductile materials used in many nuclear reactor components. Some results are presented from a test programme to obtain data by which to evaluate proposed models. Plate and pipe specimens containing surface flaws were fabricated from annealed Type 304 stainless steel and tested at room temperature. An evaluation of an empirical equation based on flow stress is presented. In essentially all instances the flow stress is not a constant but varies as a function of the size of the surface flaw. (author)

  5. Electronic Structure of the Perylene / Zinc Oxide Interface: A Computational Study of Photoinduced Electron Transfer and Impact of Surface Defects

    KAUST Repository

    Li, Jingrui

    2015-07-29

    The electronic properties of dye-sensitized semiconductor surfaces consisting of pery- lene chromophores chemisorbed on zinc oxide via different spacer-anchor groups, have been studied at the density-functional-theory level. The energy distributions of the donor states and the rates of photoinduced electron transfer from dye to surface are predicted. We evaluate in particular the impact of saturated versus unsaturated aliphatic spacer groups inserted between the perylene chromophore and the semiconductor as well as the influence of surface defects on the electron-injection rates.

  6. Electronic Structure of the Perylene / Zinc Oxide Interface: A Computational Study of Photoinduced Electron Transfer and Impact of Surface Defects

    KAUST Repository

    Li, Jingrui; Li, Hong; Winget, Paul; Bredas, Jean-Luc

    2015-01-01

    The electronic properties of dye-sensitized semiconductor surfaces consisting of pery- lene chromophores chemisorbed on zinc oxide via different spacer-anchor groups, have been studied at the density-functional-theory level. The energy distributions of the donor states and the rates of photoinduced electron transfer from dye to surface are predicted. We evaluate in particular the impact of saturated versus unsaturated aliphatic spacer groups inserted between the perylene chromophore and the semiconductor as well as the influence of surface defects on the electron-injection rates.

  7. Segmentation and Positioning in the Brazilian Kids Market: A Case Study on the Bottom of the Pyramid

    Directory of Open Access Journals (Sweden)

    Andres Rodriguez Veloso

    2012-07-01

    Full Text Available This article approaches the kids market, focusing on the Bottom of the Pyramid. A case study is developed within the toy industry. Because few studies have been developed on this subject (kids marketing, the option of this study is to focus on basic marketing strategies, market segmentation and positioning. Results exemplify how can a company structure its marketing strategy in order to have a clear focus on a given segment of the kids market.

  8. Restoring defect structures in 3C-SiC/Si (001) from spherical aberration-corrected high-resolution transmission electron microscope images by means of deconvolution processing.

    Science.gov (United States)

    Wen, C; Wan, W; Li, F H; Tang, D

    2015-04-01

    The [110] cross-sectional samples of 3C-SiC/Si (001) were observed with a spherical aberration-corrected 300 kV high-resolution transmission electron microscope. Two images taken not close to the Scherzer focus condition and not representing the projected structures intuitively were utilized for performing the deconvolution. The principle and procedure of image deconvolution and atomic sort recognition are summarized. The defect structure restoration together with the recognition of Si and C atoms from the experimental images has been illustrated. The structure maps of an intrinsic stacking fault in the area of SiC, and of Lomer and 60° shuffle dislocations at the interface have been obtained at atomic level. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Essential Roles for ARID1B in Dendritic Arborization and Spine Morphology of Developing Pyramidal Neurons

    Science.gov (United States)

    Ka, Minhan; Chopra, Divyan A.; Dravid, Shashank M.

    2016-01-01

    De novo truncating mutations in ARID1B, a chromatin-remodeling gene, cause Coffin–Siris syndrome, a developmental disorder characterized by intellectual disability and speech impairment; however, how the genetic elimination leads to cognitive dysfunction remains unknown. Thus, we investigated the neural functions of ARID1B during brain development. Here, we show that ARID1B regulates dendritic differentiation in the developing mouse brain. We knocked down ARID1B expression in mouse pyramidal neurons using in utero gene delivery methodologies. ARID1B knockdown suppressed dendritic arborization of cortical and hippocampal pyramidal neurons in mice. The abnormal development of dendrites accompanied a decrease in dendritic outgrowth into layer I. Furthermore, knockdown of ARID1B resulted in aberrant dendritic spines and synaptic transmission. Finally, ARID1B deficiency led to altered expression of c-Fos and Arc, and overexpression of these factors rescued abnormal differentiation induced by ARID1B knockdown. Our results demonstrate a novel role for ARID1B in neuronal differentiation and provide new insights into the origin of cognitive dysfunction associated with developmental intellectual disability. SIGNIFICANCE STATEMENT Haploinsufficiency of ARID1B, a component of chromatin remodeling complex, causes intellectual disability. However, the role of ARID1B in brain development is unknown. Here, we demonstrate that ARID1B is required for neuronal differentiation in the developing brain, such as in dendritic arborization and synapse formation. Our findings suggest that ARID1B plays a critical role in the establishment of cognitive circuitry by regulating dendritic complexity. Thus, ARID1B deficiency may cause intellectual disability via abnormal brain wiring induced by the defective differentiation of cortical neurons. PMID:26937011

  10. Quantum computing with defects

    Science.gov (United States)

    Varley, Joel

    2011-03-01

    The development of a quantum computer is contingent upon the identification and design of systems for use as qubits, the basic units of quantum information. One of the most promising candidates consists of a defect in diamond known as the nitrogen-vacancy (NV-1) center, since it is an individually-addressable quantum system that can be initialized, manipulated, and measured with high fidelity at room temperature. While the success of the NV-1 stems from its nature as a localized ``deep-center'' point defect, no systematic effort has been made to identify other defects that might behave in a similar way. We provide guidelines for identifying other defect centers with similar properties. We present a list of physical criteria that these centers and their hosts should meet and explain how these requirements can be used in conjunction with electronic structure theory to intelligently sort through candidate systems. To elucidate these points, we compare electronic structure calculations of the NV-1 center in diamond with those of several deep centers in 4H silicon carbide (SiC). Using hybrid functionals, we report formation energies, configuration-coordinate diagrams, and defect-level diagrams to compare and contrast the properties of these defects. We find that the NC VSi - 1 center in SiC, a structural analog of the NV-1 center in diamond, may be a suitable center with very different optical transition energies. We also discuss how the proposed criteria can be translated into guidelines to discover NV analogs in other tetrahedrally coordinated materials. This work was performed in collaboration with J. R. Weber, W. F. Koehl, B. B. Buckley, A. Janotti, C. G. Van de Walle, and D. D. Awschalom. This work was supported by ARO, AFOSR, and NSF.

  11. Evolution of the radiation-induced defect structure in 316 type stainless steel after post-irradiation annealing

    Energy Technology Data Exchange (ETDEWEB)

    Van Renterghem, W., E-mail: wvrenter@sckcen.be; Konstantinović, M.J., E-mail: mkonstan@sckcen.be; Vankeerberghen, M., E-mail: mvankeer@sckcen.be

    2014-09-15

    Highlights: • TEM study of irradiated CW316 steel after post-irradiation annealing. • Frank loops were removed after annealing at 550 °C, by unfaulting and growing. • The cavity density decreases after annealing at 550 °C, but not completely removed. • Frank loop and cavity removal is controlled by the annealing temperature. • The dissolution of γ' precipitates is controlled by the iron diffusion length. - Abstract: The thermal stability of Frank loops, black dots, cavities and γ′ precipitates in an irradiated 316 stainless steel was studied by transmission electron microscopy. The samples were retrieved from a thimble tube irradiated at around 320 °C up to 80 dpa in a commercial nuclear power reactor, and thermally annealed, varying both annealing temperature and time. With increasing annealing temperature the density of all defects gradually decreased, resulting in the complete removal of Frank loops at 550 °C. In contrast to other defects, the density of the γ′ precipitates sharply decreased with increasing annealing time, which indicates that the dissolution of the γ′ precipitates is governed by the iron diffusion length.

  12. Using Pyramids Effects as a method of nuclear and radiation protection

    International Nuclear Information System (INIS)

    Abdullayev, I.E.

    2011-01-01

    Results most of experiments fixed that When radioactive waste is placed inside the pyramids, there is a decrease in their level of radioactivity Based on result of these experiments we suggest - Using Pyramids Effects as a method of nuclear and radiation protection. Explanation of this method based on 3 factors. (2 of them - internal factors, 1 of them - external factor) Factor I. Based o the Theory of the Pyramids Effects we know, that Pyramid construction separate the normal geomagnetic field of the Earth to 2 parts, which have difference vise verse physical characteristics. Cause of the energetic barrier of side of Pyramid, internal space of the Pyramid isolate from the influence of the external normal geomagnetic field of Earth. Therefore, internal space of the Pyramid is fulfilling only by the attractive power of the Earth (pic.1)

  13. Determination of the structures of small gold clusters on stepped magnesia by density functional calculations.

    Science.gov (United States)

    Damianos, Konstantina; Ferrando, Riccardo

    2012-02-21

    The structural modifications of small supported gold clusters caused by realistic surface defects (steps) in the MgO(001) support are investigated by computational methods. The most stable gold cluster structures on a stepped MgO(001) surface are searched for in the size range up to 24 Au atoms, and locally optimized by density-functional calculations. Several structural motifs are found within energy differences of 1 eV: inclined leaflets, arched leaflets, pyramidal hollow cages and compact structures. We show that the interaction with the step clearly modifies the structures with respect to adsorption on the flat defect-free surface. We find that leaflet structures clearly dominate for smaller sizes. These leaflets are either inclined and quasi-horizontal, or arched, at variance with the case of the flat surface in which vertical leaflets prevail. With increasing cluster size pyramidal hollow cages begin to compete against leaflet structures. Cage structures become more and more favourable as size increases. The only exception is size 20, at which the tetrahedron is found as the most stable isomer. This tetrahedron is however quite distorted. The comparison of two different exchange-correlation functionals (Perdew-Burke-Ernzerhof and local density approximation) show the same qualitative trends. This journal is © The Royal Society of Chemistry 2012

  14. Understanding the Effects of Defect Modification on the Structure and Properties of Fluorinated Polymers and Implications for Capacitive Energy Storage Technologies

    Science.gov (United States)

    Gadinski, Matthew R.

    As the world begins to turn to alternative energy technologies and our electronic devices have become more both mobile and integral to everyday life, increasing interest has been focused on energy storage technologies. Capacitors are one of these energy storage technologies that utilize the polarization of an insulating material sandwiched by two electrodes as a means to store electric charge. Polymers are a preferred dielectric material for capacitors because of both their performance and practicality. However, polymer dielectrics are limited in energy density by low dielectric constant, and high loss at elevated temperature. This work aims to address these issues in order to enable polymer dielectrics for future applications and demands. As most polymer tend to have low dielectric constants (˜2-3), but impressive breakdown strengths, only a moderate improvement in dielectric constant has the potential to vastly improve the energy density of polymer capacitors. As such tremendous interest has been placed on poly(vinylidene fluoride) (PVDF) which has a dielectric of 10+ due to the highly polar C-F bonds of its backbone. To improve PVDF's performance defect monomers have been introduced to tailor the polymorphic crystalline phase to tune its properties. Additionally, this defect modification has implications for piezoelectric, electrocaloric, and thermoelectric applications of PVDF. In Chapter 2 a copolymer of VDF and bromotrifluoroethylene (BTFE) was produced. The effect of BTFE on the structure and dielectric properties of the resulting copolymer had not been previously evaluated, and its synthesis allowed for the comparison to previously reported VDF based copolymers including P(VDF-CTFE) and P(VDF-HFP). Through 19F NMR it was determined due to reactivity ratio differences of BTFE in comparison to previously explored copolymers, BTFE during synthesis is much more likely to link with itself. This results in long runs of BTFE-BTFE defects along with isolated

  15. Lectures on cosmic topological defects

    Energy Technology Data Exchange (ETDEWEB)

    Vachaspati, T [Department of Astronomy and Astrophysics, Colaba, Mumbai (India) and Physics Department, Case Western Reserve University, Cleveland (United States)

    2001-11-15

    These lectures review certain topological defects and aspects of their cosmology. Unconventional material includes brief descriptions of electroweak defects, the structure of domain walls in non-Abelian theories, and the spectrum of magnetic monopoles in SU(5) Grand Unified theory. (author)

  16. New high-pressure polymorph of In{sub 2}S{sub 3} with defect Th{sub 3}P{sub 4}-type structure

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Xiaojing; Zhu, Feng; Wu, Ye; Huang, Rong [Key Laboratory of Orogenic Belts and Crustal Evolution, MOE, Peking University, Beijing 100871 (China); School of Earth and Space Sciences, Peking University, Beijing 100871 (China); Wu, Xiang, E-mail: xiang.wu@pku.edu.cn [Key Laboratory of Orogenic Belts and Crustal Evolution, MOE, Peking University, Beijing 100871 (China); School of Earth and Space Sciences, Peking University, Beijing 100871 (China); Zhang, Qian [Key Laboratory of Orogenic Belts and Crustal Evolution, MOE, Peking University, Beijing 100871 (China); School of Earth and Space Sciences, Peking University, Beijing 100871 (China); Yang, Ke [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201204 (China); Qin, Shan, E-mail: sqin@pku.edu.cn [Key Laboratory of Orogenic Belts and Crustal Evolution, MOE, Peking University, Beijing 100871 (China); School of Earth and Space Sciences, Peking University, Beijing 100871 (China)

    2014-02-15

    The high pressure behavior of β-In{sub 2}S{sub 3} (I4{sub 1}/amd and Z=16) has been studied by in situ synchrotron radiation X-ray diffraction combined with diamond anvil cell up to 71.7 GPa. Three pressure-induced phase transitions are evidenced at ∼6.6 GPa, ∼11.1 GPa at room temperature and 35.6 GPa after the high-temperature annealing using a portable laser heating system. The new polymorph of In{sub 2}S{sub 3} at 35.6 GPa is assigned to the denser cubic defect Th{sub 3}P{sub 4} structure (I4¯3d and Z=5.333), whose unit-cell parameters are a=7.557(1) Å and V=431.6(2) Å{sup 3}. The Th{sub 3}P{sub 4}-type phase can be stable at least up to 71.7 GPa and cannot be preserved at ambient pressure. The pressure–volume relationship is well described by the second-order Birch–Murnaghan Equation of State, which yields B{sub 0}=63(3) GPa and B{sub 0}′=4 (fixed) for the β-In{sub 2}S{sub 3} phase and B{sub 0}=87(3) GPa and B{sub 0}′=4 (fixed) for the defect Th{sub 3}P{sub 4}-type phase respectively. - Graphical abstract: The structure and Rietveld refinement of new polymorph the defect Th{sub 3}P{sub 4}-type In{sub 2}S{sub 3}. This structure was observed at 35.6 GPa after laser heating by X-ray diffraction. Display Omitted - Highlights: Three pressure-induced phase transitions of β-In{sub 2}S{sub 3} were observed. β-In{sub 2}S{sub 3} was stable up to 6.6 GPa. The defect Th{sub 3}P{sub 4}-type In{sub 2}S{sub 3} was identified at 35.6 GPa after laser heating and was stable up to 71.7 GPa. Elastic properties of β-In{sub 2}S{sub 3} and Th{sub 3}P{sub 4}-type In{sub 2}S{sub 3} are well presented by Birch–Murnaghan EoS.

  17. Study by electronic structure calculations of the radiation damage in the UO2 nuclear fuel: behaviour of the point defects and fission gases

    International Nuclear Information System (INIS)

    Vathonne, Emerson

    2014-01-01

    Uranium dioxide (UO 2 ) is worldwide the most widely used fuel in nuclear plants in the world and in particular in pressurized water reactors (PWR). In-pile the fission of uranium nuclei creates fission products and point defects in the fuel. The understanding of the evolution of these radiation damages requires a multi-scale modelling approach of the nuclear fuel, from the scale of the pellet to the atomic scale. We used an electronic structure calculation method based on the density functional theory (DFT) to model radiation damage in UO 2 at the atomic scale. A Hubbard-type Coulomb interaction term is added to the standard DFT formalism to take into account the strong correlations of the 5f electrons in UO 2 . This method is used to study point defects with various charge states and the incorporation and diffusion of krypton in uranium dioxide. This study allowed us to obtain essential data for higher scale models but also to interpret experimental results. In parallel of this study, three ways to improve the state of the art of electronic structure calculations of UO 2 have been explored: the consideration of the spin-orbit coupling neglected in current point defect calculations, the application of functionals allowing one to take into account the non-local interactions such as van der Waals interactions important for rare gases and the use of the Dynamical Mean Field Theory combined to the DFT method in order to take into account the dynamical effects in the 5f electron correlations. (author) [fr

  18. Building online genomics applications using BioPyramid.

    Science.gov (United States)

    Stephenson, Liam; Wakeham, Yoshua; Seidenman, Nick; Choi, Jarny

    2018-03-29

    BioPyramid is a python package, which serves as a scaffold for building an online application for the exploration of gene expression data. It is designed for bioinformaticians wishing to quickly share transformed data and interactive analyses with collaborators. Current R-based tools similarly address the need to quickly share "omics"-data in an exploratory format, but these are generally small-scale, single-dataset solutions. Biopyramid is written in python pyramid framework and scalable to address longer-term or more complex projects. It contains a number of components designed to reduce the time and effort in building such an application from scratch, including gene annotation, dataset models and visualisation tools. Freely available at http://github.com/jarny/biopyramid. Implemented in python and javascript. jarnyc@unimelb.edu.au.

  19. Embedded defects

    International Nuclear Information System (INIS)

    Barriola, M.; Vachaspati, T.; Bucher, M.

    1994-01-01

    We give a prescription for embedding classical solutions and, in particular, topological defects in field theories which are invariant under symmetry groups that are not necessarily simple. After providing examples of embedded defects in field theories based on simple groups, we consider the electroweak model and show that it contains the Z string and a one-parameter family of strings called the W(α) string. It is argued that although the members of this family are gauge equivalent when considered in isolation, each member becomes physically distinct when multistring configurations are considered. We then turn to the issue of stability of embedded defects and demonstrate the instability of a large class of such solutions in the absence of bound states or condensates. The Z string is shown to be unstable for all values of the Higgs boson mass when θ W =π/4. W strings are also shown to be unstable for a large range of parameters. Embedded monopoles suffer from the Brandt-Neri-Coleman instability. Finally, we connect the electroweak string solutions to the sphaleron

  20. Subtle Motion Analysis and Spotting using the Riesz Pyramid

    OpenAIRE

    Arango , Carlos ,; Alata , Olivier; Emonet , Rémi; Legrand , Anne-Claire; Konik , Hubert

    2018-01-01

    International audience; Analyzing and temporally spotting motions which are almost invisible to the human eye might reveal interesting information about the world. However, detecting these events is difficult due to their short duration and low intensities. Taking inspiration from video magnification techniques, we design a workflow for analyzing and temporally spotting subtle motions based on the Riesz pyramid. In addition, we propose a filtering and masking scheme that segments motions of i...