WorldWideScience

Sample records for pure ultrasonic communication

  1. Ultrasonic Communication Project, Phase 1, FY1999

    Energy Technology Data Exchange (ETDEWEB)

    Haynes, H.D.; Akerman, M.A.; Baylor, V.M.

    2000-06-01

    This Phase 1 project has been successful in identifying, exploring, and demonstrating methods for ultrasonic-based communication with an emphasis on the application of digital signal processing techniques. During the project, at the direction of the agency project monitor, particular attention was directed at sending and receiving ultrasonic data through air and through pipes that would be commonly found in buildings. Efforts were also focused on development of a method for transmitting computer files ultrasonically. New methods were identified and evaluated for ultrasonic communication. These methods are based on a technique called DFS. With DFS, individual alphanumeric characters are broken down into a sequence of bits, and each bit is used to generate a discrete ultrasonic frequency. Characters are then transmitted one-bit-at-a-time, and reconstructed by the receiver. This technique was put into practice through the development of LabVIEW{trademark}VIs. These VIs were integrated with specially developed electronic circuits to provide a system for demonstrating the transmission and reception/reconstruction of typed messages and computer files. Tests were performed to determine the envelope for ultrasound transmission through pipes (with and without water) versus through air. The practical aspects of connections, efficient electronics, impedance matching, and the effect of damping mechanisms were all investigated. These tests resulted in a considerable number of reference charts that illustrate the absorption of ultrasound through different pipe materials, both with and without water, as a function of distance. Ultrasound was found to be least attenuated by copper pipe and most attenuated by PVC pipe. Water in the pipe provides additional damping and attenuation of ultrasonic signals. Dramatic improvements are observed, however, in ultrasound signal strength if the transducers are directly coupled to the water, rather than simply attaching them to the outside of

  2. Frogs Communicate by Means of Ultrasonic Sounds

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ People are always fascinated by ways that some members of mammalian species (such as dolphins, bats and some rodents) communicate using sounds that we cannot hear. But think twice if you say the capacity of producing and detecting ultrasounds (frequencies greater than 20kHz) is limited to mammalians. A study implemented by Prof. SHEN Junxian from the CAS Institute of Biophysics (IBP) and colleagues in CAS and abroad showed that a rare frog species in China should also be added to that list. It is the first documented case of a non-mammalian species being able to use ultrasonic communication. Their work was reported in the March 16 issue of the journal Nature.

  3. Grain fragmentation in ultrasonic-assisted TIG weld of pure aluminum.

    Science.gov (United States)

    Chen, Qihao; Lin, Sanbao; Yang, Chunli; Fan, Chenglei; Ge, Hongliang

    2017-11-01

    Under the action of acoustic waves during an ultrasonic-assisted tungsten inert gas (TIG) welding process, a grain of a TIG weld of aluminum alloy is refined by nucleation and grain fragmentation. Herein, effects of ultrasound on grain fragmentation in the TIG weld of aluminum alloy are investigated via systematic welding experiments of pure aluminum. First, experiments involving continuous and fixed-position welding are performed, which demonstrate that ultrasound can break the grain of the TIG weld of pure aluminum. The microstructural characteristics of an ultrasonic-assisted TIG weld fabricated by fixed-position welding are analyzed. The microstructure is found to transform from plane crystal, columnar crystal, and uniform equiaxed crystal into plane crystal, deformed columnar crystal, and nonuniform equiaxed crystal after application of ultrasound. Second, factors influencing ultrasonic grain fragmentation are investigated. The ultrasonic amplitude and welding current are found to have a considerable effect on grain fragmentation. The degree of fragmentation first increases and then decreases with an increase in ultrasonic amplitude, and it increases with an increase in welding current. Measurement results of the vibration of the weld pool show that the degree of grain fragmentation is related to the intensity of acoustic nonlinearity in the weld pool. The greater the intensity of acoustic nonlinearity, the greater is the degree of grain fragmentation. Finally, the mechanism of ultrasonic grain fragmentation in the TIG weld of pure aluminum is discussed. A finite element simulation is used to simulate the acoustic pressure and flow in the weld pool. The acoustic pressure in the weld pool exceeds the cavitation threshold, and cavitation bubbles are generated. The flow velocity in the weld pool does not change noticeably after application of ultrasound. It is concluded that the high-pressure conditions induced during the occurrence of cavitation, lead to grain

  4. Ultrasonic Transducers for Air and Underwater Communication.

    Science.gov (United States)

    Koosha, Abdolrahim

    Available from UMI in association with The British Library. The performance of a novel radiator capable of producing ultrasonic waves in air and liquids has been investigated. For commercial transducers when operating in air or liquids, impedance matching is the necessary condition for maximum transfer of energy to the medium (thus no standing waves are involved). However, for this radiator the formation of the mechanical standing waves on it is the key condition for directional radiation of energy into the surrounding environment. Under this condition the radiator exhibits a practical conversion of electrical energy into ultrasound. To further improve the performance of the radiator the wavelength coincidence condition must be satisfied. This condition implies that the wavelength of the bending vibration developed on the blade to be the same as that in the medium to which it is coupled. Consequently, an end-fire radiation pattern is obtained. The theory of this when applied to water and also for a double blade configuration are presented. The main component of the radiator consists of a cantilever blade on which a pair of piezoelectric (PZT) ceramic bars are fixed. These the so called excitation gauges, are fixed on both sides of a thin rectangular metal blade near the clamped end. When wavelength coincidence condition is fulfilled, the radiator transmits ultrasonic wave in a highly directional pattern. The direction of propagation of ultrasound is solely steered by frequency of the applied signal. System imperfections such as inter modal coupling when used underwater are considered. An analytical approach is developed to investigate the performance of the radiator for transmission of digital signals in air as well as in water. This method is used to evaluate the efficiency of the device as a suitable means for communication between divers or a diver and an underwater stationary station. Amplitude modulation of speech signals demonstrated the capabilities of a new

  5. The effect of ultrasonic impact treatment on surface roughening of commercially pure titanium during tensile test

    Science.gov (United States)

    Kozelskaya, Anna; Panin, Alexey; Kazachenok, Marina; Romanova, Varvara; Pochivalov, Yurii

    2016-11-01

    The effect of ultrasonic impact treatment (UIT) on surface roughening of commercially pure titanium specimens under uniaxial tension was investigated. It was shown that the inhibition of the dislocation glide in the specimens subject to the preliminary UIT led smoothing of their surface profile at the meso-and microscale levels. Macroscopic roughening of the surface of the untreated specimens and specimens subjected to preliminary UIT was the same and was determined by the deformation of the underlying grains.

  6. Strain localization of commercially pure titanium subjected to ultrasonic impact treatment followed by uniaxial tension

    Science.gov (United States)

    Panin, Alexey; Kazachenok, Marina; Kozelskaya, Anna; Perevalova, Olga; Balokhonov, Ruslan; Romanova, Varvara; Pochivalov, Yurii

    2016-11-01

    It was demonstrated that the ultrasonic impact treatment results in the gradient microstructure of the surface layer of commercially pure titanium composed of nanosized nonequiaxial α-Ti grains, underlying course α-grains with banded substructure and deformation twins, and subjacent layer characterized by the presence of a few twins and extinction contours within the course grains. The effect of ultrasonic impact treatment on the mechanical behavior of titanium specimen under tension was revealed theoretically and experimentally Using optical and atomic force microscopes it was shown that the fine-grained surface layer impede dislocation motion causing the initiation and propagation of shear bands oriented along the direction of maximum shear stresses. The fine structure of shear bands was studied by transmission electron microscopy.

  7. Recording Mouse Ultrasonic Vocalizations to Evaluate Social Communication.

    Science.gov (United States)

    Ferhat, Allain-Thibeault; Torquet, Nicolas; Le Sourd, Anne-Marie; de Chaumont, Fabrice; Olivo-Marin, Jean-Christophe; Faure, Philippe; Bourgeron, Thomas; Ey, Elodie

    2016-06-05

    Mice emit ultrasonic vocalizations in different contexts throughout development and in adulthood. These vocal signals are now currently used as proxies for modeling the genetic bases of vocal communication deficits. Characterizing the vocal behavior of mouse models carrying mutations in genes associated with neuropsychiatric disorders such as autism spectrum disorders will help to understand the mechanisms leading to social communication deficits. We provide here protocols to reliably elicit ultrasonic vocalizations in pups and in adult mice. This standardization will help reduce inter-study variability due to the experimental settings. Pup isolation calls are recorded throughout development from individual pups isolated from dam and littermates. In adulthood, vocalizations are recorded during same-sex interactions (without a sexual component) by exposing socially motivated males or females to an unknown same-sex conspecific. We also provide a protocol to record vocalizations from adult males exposed to an estrus female. In this context, there is a sexual component in the interaction. These protocols are established to elicit a large amount of ultrasonic vocalizations in laboratory mice. However, we point out the important inter-individual variability in the vocal behavior of mice, which should be taken into account by recording a minimal number of individuals (at least 12 in each condition). These recordings of ultrasonic vocalizations are used to evaluate the call rate, the vocal repertoire and the acoustic structure of the calls. Data are combined with the analysis of synchronous video recordings to provide a more complete view on social communication in mice. These protocols are used to characterize the vocal communication deficits in mice lacking ProSAP1/Shank2, a gene associated with autism spectrum disorders. More ultrasonic vocalizations recordings can also be found on the mouseTube database, developed to favor the exchange of such data.

  8. Evaluation of multiple-channel OFDM based airborne ultrasonic communications.

    Science.gov (United States)

    Jiang, Wentao; Wright, William M D

    2016-09-01

    Orthogonal frequency division multiplexing (OFDM) modulation has been extensively used in both wired and wireless communication systems. The use of OFDM technology allows very high spectral efficiency data transmission without using complex equalizers to correct the effect of a frequency-selective channel. This work investigated OFDM methods in an airborne ultrasonic communication system, using commercially available capacitive ultrasonic transducers operating at 50kHz to transmit information through the air. Conventional modulation schemes such as binary phase shift keying (BPSK) and quadrature amplitude modulation (QAM) were used to modulate sub-carrier signals, and the performances were evaluated in an indoor laboratory environment. Line-of-sight (LOS) transmission range up to 11m with no measurable errors was achieved using BPSK at a data rate of 45kb/s and a spectral efficiency of 1b/s/Hz. By implementing a higher order modulation scheme (16-QAM), the system data transfer rate was increased to 180kb/s with a spectral efficiency of 4b/s/Hz at attainable transmission distances up to 6m. Diffraction effects were incorporated into a model of the ultrasonic channel that also accounted for beam spread and attenuation in air. The simulations were a good match to the measured signals and non-LOS signals could be demodulated successfully. The effects of multipath interference were also studied in this work. By adding cyclic prefix (CP) to the OFDM symbols, the bit error rate (BER) performance was significantly improved in a multipath environment.

  9. Measurement and Modeling of Narrowband Channels for Ultrasonic Underwater Communications

    Science.gov (United States)

    Cañete, Francisco J.; López-Fernández, Jesús; García-Corrales, Celia; Sánchez, Antonio; Robles, Encarnación; Rodrigo, Francisco J.; Paris, José F.

    2016-01-01

    Underwater acoustic sensor networks are a promising technology that allow real-time data collection in seas and oceans for a wide variety of applications. Smaller size and weight sensors can be achieved with working frequencies shifted from audio to the ultrasonic band. At these frequencies, the fading phenomena has a significant presence in the channel behavior, and the design of a reliable communication link between the network sensors will require a precise characterization of it. Fading in underwater channels has been previously measured and modeled in the audio band. However, there have been few attempts to study it at ultrasonic frequencies. In this paper, a campaign of measurements of ultrasonic underwater acoustic channels in Mediterranean shallow waters conducted by the authors is presented. These measurements are used to determine the parameters of the so-called κ-μ shadowed distribution, a fading model with a direct connection to the underlying physical mechanisms. The model is then used to evaluate the capacity of the measured channels with a closed-form expression. PMID:26907281

  10. Measurement and Modeling of Narrowband Channels for Ultrasonic Underwater Communications

    Directory of Open Access Journals (Sweden)

    Francisco J. Cañete

    2016-02-01

    Full Text Available Underwater acoustic sensor networks are a promising technology that allow real-time data collection in seas and oceans for a wide variety of applications. Smaller size and weight sensors can be achieved with working frequencies shifted from audio to the ultrasonic band. At these frequencies, the fading phenomena has a significant presence in the channel behavior, and the design of a reliable communication link between the network sensors will require a precise characterization of it. Fading in underwater channels has been previously measured and modeled in the audio band. However, there have been few attempts to study it at ultrasonic frequencies. In this paper, a campaign of measurements of ultrasonic underwater acoustic channels in Mediterranean shallow waters conducted by the authors is presented. These measurements are used to determine the parameters of the so-called κ-μ shadowed distribution, a fading model with a direct connection to the underlying physical mechanisms. The model is then used to evaluate the capacity of the measured channels with a closed-form expression.

  11. Measurement and Modeling of Narrowband Channels for Ultrasonic Underwater Communications.

    Science.gov (United States)

    Cañete, Francisco J; López-Fernández, Jesús; García-Corrales, Celia; Sánchez, Antonio; Robles, Encarnación; Rodrigo, Francisco J; Paris, José F

    2016-01-01

    Underwater acoustic sensor networks are a promising technology that allow real-time data collection in seas and oceans for a wide variety of applications. Smaller size and weight sensors can be achieved with working frequencies shifted from audio to the ultrasonic band. At these frequencies, the fading phenomena has a significant presence in the channel behavior, and the design of a reliable communication link between the network sensors will require a precise characterization of it. Fading in underwater channels has been previously measured and modeled in the audio band. However, there have been few attempts to study it at ultrasonic frequencies. In this paper, a campaign of measurements of ultrasonic underwater acoustic channels in Mediterranean shallow waters conducted by the authors is presented. These measurements are used to determine the parameters of the so-called κ-μ shadowed distribution, a fading model with a direct connection to the underlying physical mechanisms. The model is then used to evaluate the capacity of the measured channels with a closed-form expression.

  12. Nanodiamond films deposited at moderate temperature on pure titanium substrate pretreated by ultrasonic scratching in diamond powder suspension

    Institute of Scientific and Technical Information of China (English)

    Syed Jawid Askari; Fanxiu Lv; Akhtar Farid; Fengying Wang; Qi He; Zuyuan Zhou

    2006-01-01

    Nanocrystalline diamond (NCD) film deposition on pure titanium and Ti alloys is extraordinarily difficult because of the high diffusion coefficient of carbon in Ti, the large mismatch in their thermal expansion coefficients, the complex nature of the interlayer formed during diamond deposition, and the difficulty to achieve very high nucleation density. In this investigation, NCD films were successfully deposited on pure Ti substrate by using a novel substrate pretreatment of ultrasonic scratching in a diamond powder-ethanol suspension and by a two-step process at moderate temperature. It was shown that by scratching with a 30-μm diamond suspension for 1 h, followed by a 10-h diamond deposition, a continuous NCD film was obtained with an average grain size of about 200 nm. Detailed experimental results on the preparation, characterization, and successful deposition of the NCD films on Ti were discussed.

  13. short communication densities and ultrasonic speed of 2-hydroxy-5 ...

    African Journals Online (AJOL)

    Preferred Customer

    important probe for the study of structure and properties of matter [6]. Ultrasonic speed ... those which provide a physical meaning to the parameters in their expression, allowing the ... a wide range of both organic and inorganic compounds.

  14. Interdigital Piezopolymer Transducers for Time of Flight Measurements with Ultrasonic Lamb Waves on Carbon-Epoxy Composites under Pure Bending Stress

    OpenAIRE

    Andrea Bulletti; Lorenzo Capineri

    2015-01-01

    Interdigital transducers fabricated with piezopolymer film have been realized to excite ultrasonic Lamb waves in a composite laminate subjected to pure bending stresses. Lamb waves were generated and detected in a cross-ply [0°/90°] 4 mm thick carbon-fiber composite, by using two interdigital transducers in pitch-catch configuration. We demonstrate that the choice of the piezopolymer transducer technology is suitable for this type of investigation and the advantages of the proposed transducer...

  15. Quantum secure direct communication with quantum encryption based on pure entangled states

    Institute of Scientific and Technical Information of China (English)

    Li Xi-Han; Li Chun-Yan; Deng Fu-Guo; Zhou Ping; Liang Yu-Jie; Zhou Hong-Yu

    2007-01-01

    This paper presents a scheme for quantum secure direct communication with quantum encryption. The two authorized users use repeatedly a sequence of the pure entangled pairs (quantum key) shared for encrypting and decrypting the secret message carried by the travelling photons directly. For checking eavesdropping, the two parties perform the single-photon measurements on some decoy particles before each round. This scheme has the advantage that the pure entangled quantum signal source is feasible at present and any eavesdropper cannot steal the message.

  16. Ultrasonic wireless broadband communication system for underwater applications

    OpenAIRE

    Martins, Marcos Silva

    2013-01-01

    Tese de doutoramento do Programa Doutoral em Engenharia Eletrónica e de Computadores Underwater wireless communication systems are becoming a priority in terms of research and technological development due to the increasing demand for exploring the oceans’ potential in areas such as pharmaceutical, oil, minerals, environmental and biodiversity. This demand is increasing exponentially with the need for high data rate and near-real-time communications between submerged mobile and...

  17. Rodent ultrasonic communication: Male prosocial 50-kHz ultrasonic vocalizations elicit social approach behavior in female rats (Rattus norvegicus).

    Science.gov (United States)

    Willadsen, Maria; Seffer, Dominik; Schwarting, Rainer K W; Wöhr, Markus

    2014-02-01

    Rats emit distinct types of ultrasonic vocalizations (USV), which serve as situation-dependent affective signals with important communicative functions. Low-frequency 22-kHz USV typically occur in aversive situations, such as social defeat, whereas high-frequency 50-kHz USV can be observed in appetitive situations, like rough-and-tumble-play in juveniles or mating in adults. The 2 main USV types serve distinct communicative functions and induce call-specific behavioral responses in the receiver. While 22-kHz USV probably serve as alarm calls, 50-kHz USV appear to serve a prosocial communicative function in the sexual and the nonsexual context. In the sexual context, however, this view has recently been challenged by playback studies where only very limited behavioral changes were observed in response to prosocial 50-kHz USV. The aim of the present study was therefore to test whether female rats display social approach behavior in response to male prosocial 50-kHz USV by means of our established playback paradigm. To this aim, we exposed female rats to playback of the following 2 acoustic stimuli: (a) natural male 50-kHz USV and (b) time- and amplitude-matched white noise, with the latter serving as acoustic control for novelty-induced changes in behavior not linked to the communicative function of male prosocial 50-kHz USV. Our present findings show that female rats display high levels of social approach behavior in response to male prosocial 50-kHz USV, but not time- and amplitude-matched white noise, supporting the conclusion that male prosocial 50-kHz USV are likely to play an important role in establishing social proximity and possibly regulate mating behavior.

  18. Affective communication in rodents: ultrasonic vocalizations as a tool for research on emotion and motivation.

    Science.gov (United States)

    Wöhr, Markus; Schwarting, Rainer K W

    2013-10-01

    Mice and rats emit and perceive calls in the ultrasonic range, i.e., above the human hearing threshold of about 20 kHz: so-called ultrasonic vocalizations (USV). Juvenile and adult rats emit 22-kHz USV in aversive situations, such as predator exposure and fighting or during drug withdrawal, whereas 50-kHz USV occur in appetitive situations, such as rough-and-tumble play and mating or in response to drugs of abuse, e.g., amphetamine. Aversive 22-kHz USV and appetitive 50-kHz USV serve distinct communicative functions. Whereas 22-kHz USV induce freezing behavior in the receiver, 50-kHz USV lead to social approach behavior. These opposite behavioral responses are paralleled by distinct patterns of brain activation. Freezing behavior in response to 22-kHz USV is paralleled by increased neuronal activity in brain areas regulating fear and anxiety, such as the amygdala and periaqueductal gray, whereas social approach behavior elicited by 50-kHz USV is accompanied by reduced activity levels in the amygdala but enhanced activity in the nucleus accumbens, a brain area implicated in reward processing. These opposing behavioral responses, together with distinct patterns of brain activation, particularly the bidirectional tonic activation or deactivation of the amygdala elicited by 22-kHz and 50-kHz USV, respectively, concur with a wealth of behavioral and neuroimaging studies in humans involving emotionally salient stimuli, such as fearful and happy facial expressions. Affective ultrasonic communication therefore offers a translational tool for studying the neurobiology underlying socio-affective communication. This is particularly relevant for rodent models of neurodevelopmental disorders characterized by social and communication deficits, such as autism and schizophrenia.

  19. Ultrasonic Digital Communication System for a Steel Wall Multipath Channel: Methods and Results

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, Timothy L. [Rensselaer Polytechnic Inst., Troy, NY (United States)

    2005-12-01

    As of the development of this thesis, no commercially available products have been identified for the digital communication of instrumented data across a thick ({approx} 6 n.) steel wall using ultrasound. The specific goal of the current research is to investigate the application of methods for digital communication of instrumented data (i.e., temperature, voltage, etc.) across the wall of a steel pressure vessel. The acoustic transmission of data using ultrasonic transducers prevents the need to breach the wall of such a pressure vessel which could ultimately affect its safety or lifespan, or void the homogeneity of an experiment under test. Actual digital communication paradigms are introduced and implemented for the successful dissemination of data across such a wall utilizing solely an acoustic ultrasonic link. The first, dubbed the ''single-hop'' configuration, can communicate bursts of digital data one-way across the wall using the Differential Binary Phase-Shift Keying (DBPSK) modulation technique as fast as 500 bps. The second, dubbed the ''double-hop'' configuration, transmits a carrier into the vessel, modulates it, and retransmits it externally. Using a pulsed carrier with Pulse Amplitude Modulation (PAM), this technique can communicate digital data as fast as 500 bps. Using a CW carrier, Least Mean-Squared (LMS) adaptive interference suppression, and DBPSK, this method can communicate data as fast as 5 kbps. A third technique, dubbed the ''reflected-power'' configuration, communicates digital data by modulating a pulsed carrier by varying the acoustic impedance at the internal transducer-wall interface. The paradigms of the latter two configurations are believed to be unique. All modulation methods are based on the premise that the wall cannot be breached in any way and can therefore be viably implemented with power delivered wirelessly through the acoustic channel using ultrasound. Methods

  20. mouseTube – a database to collaboratively unravel mouse ultrasonic communication [version 1; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Nicolas Torquet

    2016-09-01

    Full Text Available Ultrasonic vocalisation is a broadly used proxy to evaluate social communication in mouse models of neuropsychiatric disorders. The efficacy and robustness of testing these models suffer from limited knowledge of the structure and functions of these vocalisations as well as of the way to analyse the data. We created mouseTube, an open database with a web interface, to facilitate sharing and comparison of ultrasonic vocalisations data and metadata attached to a recording file. Metadata describe 1 the acquisition procedure, e.g., hardware, software, sampling frequency, bit depth; 2 the biological protocol used to elicit ultrasonic vocalisations; 3 the characteristics of the individual emitting ultrasonic vocalisations (e.g., strain, sex, age. To promote open science and enable reproducibility, data are made freely available. The website provides searching functions to facilitate the retrieval of recording files of interest. It is designed to enable comparisons of ultrasonic vocalisation emission between strains, protocols or laboratories, as well as to test different analysis algorithms and to search for protocols established to elicit mouse ultrasonic vocalisations. Over the long term, users will be able to download and compare different analysis results for each data file. Such application will boost the knowledge on mouse ultrasonic communication and stimulate sharing and comparison of automatic analysis methods to refine phenotyping techniques in mouse models of neuropsychiatric disorders.

  1. Effects of amphetamine on pro-social ultrasonic communication in juvenile rats: Implications for mania models.

    Science.gov (United States)

    Engelhardt, K-Alexander; Fuchs, Eberhard; Schwarting, Rainer K W; Wöhr, Markus

    2017-03-01

    Communication is the act of information transfer between sender and receiver. In rats, vocal communication can be studied through ultrasonic vocalizations (USV). 50-kHz USV occur in appetitive situations, most notably juvenile play, likely expressing the sender׳s positive affective state. Such appetitive 50-kHz USV serve important pro-social communicative functions and elicit social exploratory and approach behavior in the receiver. Emission of 50-kHz USV can be induced pharmacologically by the administration of psychostimulant drugs, such as amphetamine. However, it is unknown whether amphetamine affects the pro-social communicative function of 50-kHz USV in the receiver. We therefore assessed dose-response effects of amphetamine (0.0mg/kg, 0.5mg/kg, 1.0mg/kg, 2.5mg/kg, 5.0mg/kg) on pro-social ultrasonic communication on both, sender and receiver, in juvenile rats. We found an inverted U-shaped effect of amphetamine on 50-kHz USV emission, with 50-kHz USV levels being strongly enhanced by moderate doses, yet less prominent effects were seen following the highest dose. Likewise, amphetamine exerted inverted U-shaped effects on social exploratory and approach behavior induced by playback of appetitive 50-kHz USV. Social approach was enhanced by moderate amphetamine doses, but completely abolished following the highest dose. Amphetamine further dose-dependently promoted the emission of 50-kHz USV following playback of appetitive 50-kHz USV, indicating more vigorous attempts to establish social proximity. Our results support an important role of dopamine in closing a perception-and-action-loop through linking mechanisms relevant for detection and production of social vocalizations. Moreover, our approach possibly provides a new means to study mania-like aberrant social interaction and communication in animal models for bipolar disorder.

  2. Entanglement manipulation of multipartite pure states with finite rounds of classical communication

    Science.gov (United States)

    de Vicente, J. I.; Spee, C.; Sauerwein, D.; Kraus, B.

    2017-01-01

    We studied pure state transformations using local operations assisted by finitely many rounds of classical communication (LOCCIN) [C. Spee, J. I. de Vicente, D. Sauerwein, and B. Kraus [Phys. Rev. Lett. (to be published)], arXiv:1606.04418]. Here, we present the details of some of the proofs and generalize the construction of examples of state transformations via LOCCIN which require a probabilistic step. However, we also present explicit examples of SLOCC classes where any separable transformation can be realized by a protocol in which each step is deterministic (all-det-LOCCIN). Such transformations can be considered as natural generalizations of bipartite transformations. Furthermore, we provide examples of pure state transformations which are possible via separable transformations, but not via LOCCIN. We also analyze an interesting genuinely multipartite effect which we call locking or unlocking the power of other parties. This means that one party can prevent or enable the implementation of LOCC transformations by other parties. Moreover, we investigate the maximally entangled set restricted to LOCCIN and show how easily computable bounds on some entanglement measures can be derived by restricting to LOCCIN.

  3. Standard practice for digital imaging and communication in nondestructive evaluation (DICONDE) for ultrasonic test methods

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This practice facilitates the interoperability of ultrasonic imaging equipment by specifying image data transfer and archival storage methods in commonly accepted terms. This document is intended to be used in conjunction with Practice E 2339 on Digital Imaging and Communication in Nondestructive Evaluation (DICONDE). Practice E 2339 defines an industrial adaptation of the NEMA Standards Publication titled Digital Imaging and Communications in Medicine (DICOM, see http://medical.nema.org), an international standard for image data acquisition, review, transfer and archival storage. The goal of Practice E 2339, commonly referred to as DICONDE, is to provide a standard that facilitates the display and analysis of NDE test results on any system conforming to the DICONDE standard. Toward that end, Practice E 2339 provides a data dictionary and set of information modules that are applicable to all NDE modalities. This practice supplements Practice E 2339 by providing information object definitions, information ...

  4. Interdigital Piezopolymer Transducers for Time of Flight Measurements with Ultrasonic Lamb Waves on Carbon-Epoxy Composites under Pure Bending Stress

    Directory of Open Access Journals (Sweden)

    Andrea Bulletti

    2015-01-01

    Full Text Available Interdigital transducers fabricated with piezopolymer film have been realized to excite ultrasonic Lamb waves in a composite laminate subjected to pure bending stresses. Lamb waves were generated and detected in a cross-ply [0°/90°] 4 mm thick carbon-fiber composite, by using two interdigital transducers in pitch-catch configuration. We demonstrate that the choice of the piezopolymer transducer technology is suitable for this type of investigation and the advantages of the proposed transducer assembly and bonding are described. A full set-up is described to determine the relationship between the time of flight of the recorded signals and the applied bending moment. Interdigital transducers were designed according to simulations of the dispersion curves, in order to operate at a central frequency of 450 kHz. This frequency corresponds to a central wavelength of 16 mm and to a group velocity of about 6000 m/s for the first symmetric guided wave mode. The variations in the time of flight of ultrasonic recorded signals were measured as a function of the variations in the bending moment. The static and dynamic load tests were in good agreement with strain gage measurements performed in the micro deformation range (0–1400 µm/m.

  5. The communication of "pure" group-based anger reduces tendencies toward intergroup conflict because it increases out-group empathy.

    Science.gov (United States)

    de Vos, Bart; van Zomeren, Martijn; Gordijn, Ernestine H; Postmes, Tom

    2013-08-01

    The communication of group-based anger in intergroup conflict is often associated with destructive conflict behavior. However, we show that communicating group-based anger toward the out-group can evoke empathy and thus reduce intergroup conflict. This is because it stresses the value of maintaining a positive long-term intergroup relationship, thereby increasing understanding for the situation (in contrast to the communication of the closely related emotion of contempt). Three experiments demonstrate that the communication of group-based anger indeed reduces destructive conflict intentions compared with (a) a control condition (Experiments 1-2), (b) the communication of group-based contempt (Experiment 2), and (c) the communication of a combination of group-based anger and contempt (Experiments 2-3). Moreover, results from all three experiments reveal that empathy mediated the positive effect of communicating "pure" group-based anger. We discuss the implications of these findings for the theory and practice of communicating emotions in intergroup conflicts.

  6. Full-Duplex Airborne Ultrasonic Data Communication Using a Pilot-Aided QAM-OFDM Modulation Scheme.

    Science.gov (United States)

    Jiang, Wentao; Wright, William M D

    2016-08-01

    Orthogonal frequency division multiplexing (OFDM) has been extensively used in a variety of broadband digital wireless communications applications because of its high bandwidth utilization efficiency and effective immunity to multipath distortion. This paper has investigated quadrature amplitude modulation and OFDM methods in air-coupled ultrasonic communication, using broadband capacitive ultrasonic transducers with high- k dielectric layers. OFDM phase noise was discussed and corrected using a pilot-aided estimation algorithm. The overall system data rate achieved was up to 400 kb/s with a spectral efficiency of 2 b/s/Hz. An ultrasonic propagation model for signal prediction considered atmospheric absorption of sound in air, beam divergence, and transducer frequency response. The simulations were compared with the experimental results, and good agreement was found between the two. Two-way communication through air was also implemented successfully by applying three-way handshaking initialization and an adaptive modulation scheme with variable data rates depending on the transmission distance, estimated using received signal strength indication measurement. It was shown that the error-free transmission range could be extended up to 2.5 m using different system transfer rates from 400 kb/s down to 100 kb/s. In full-duplex transmission mode, the overall error-free system data rate achieved was 0.8 Mb/s up to 1.5 m.

  7. Communication Impairment in Ultrasonic Vocal Repertoire during the Suckling Period of Cd157 Knockout Mice: Transient Improvement by Oxytocin.

    Science.gov (United States)

    Lopatina, Olga L; Furuhara, Kazumi; Ishihara, Katsuhiko; Salmina, Alla B; Higashida, Haruhiro

    2017-01-01

    Communication consists of social interaction, recognition, and information transmission. Communication ability is the most affected component in children with autism spectrum disorder (ASD). Recently, we reported that the CD157/BST1 gene is associated with ASD, and that CD157 knockout (Cd157(-/-)) mice display severe impairments in social behavior that are improved by oxytocin (OXT) treatment. Here, we sought to determine whether Cd157(-/-) mice can be used as a suitable model for communication deficits by measuring ultrasonic vocalizations (USVs), especially in the early developmental stage. Call number produced in pups due to isolation from dams was higher at postnatal day (PND) 3 in knockout pups than wild-type mice, but was lower at PNDs 7 and 10. Pups of both genotypes had similarly limited voice repertoires at PND 3. Later on, at PNDs 7 and 10, while wild-type pups emitted USVs consisting of six different syllable types, knockout pups vocalized with only two types. This developmental impairment in USV emission was rescued within 30 min by intraperitoneal OXT treatment, but quickly returned to control levels after 120 min, showing a transient effect of OXT. USV impairment was partially observed in Cd157(+/-) heterozygous mice, but not in Cd157(-/-) adult male mice examined while under courtship. These results demonstrate that CD157 gene deletion results in social communication insufficiencies, and suggests that CD157 is likely involved in acoustic communication. This unique OXT-sensitive developmental delay in Cd157(-/-) pups may be a useful model of communicative interaction impairment in ASD.

  8. Communication Impairment in Ultrasonic Vocal Repertoire during the Suckling Period of Cd157 Knockout Mice: Transient Improvement by Oxytocin

    Directory of Open Access Journals (Sweden)

    Olga L. Lopatina

    2017-05-01

    Full Text Available Communication consists of social interaction, recognition, and information transmission. Communication ability is the most affected component in children with autism spectrum disorder (ASD. Recently, we reported that the CD157/BST1 gene is associated with ASD, and that CD157 knockout (Cd157−/− mice display severe impairments in social behavior that are improved by oxytocin (OXT treatment. Here, we sought to determine whether Cd157−/− mice can be used as a suitable model for communication deficits by measuring ultrasonic vocalizations (USVs, especially in the early developmental stage. Call number produced in pups due to isolation from dams was higher at postnatal day (PND 3 in knockout pups than wild-type mice, but was lower at PNDs 7 and 10. Pups of both genotypes had similarly limited voice repertoires at PND 3. Later on, at PNDs 7 and 10, while wild-type pups emitted USVs consisting of six different syllable types, knockout pups vocalized with only two types. This developmental impairment in USV emission was rescued within 30 min by intraperitoneal OXT treatment, but quickly returned to control levels after 120 min, showing a transient effect of OXT. USV impairment was partially observed in Cd157+/− heterozygous mice, but not in Cd157−/− adult male mice examined while under courtship. These results demonstrate that CD157 gene deletion results in social communication insufficiencies, and suggests that CD157 is likely involved in acoustic communication. This unique OXT-sensitive developmental delay in Cd157−/− pups may be a useful model of communicative interaction impairment in ASD.

  9. Ultrasonic communication in rats: effects of morphine and naloxone on vocal and behavioral responses to playback of 50-kHz vocalizations.

    Science.gov (United States)

    Wöhr, Markus; Schwarting, Rainer K W

    2009-12-01

    Rats emit ultrasonic vocalizations and it was hypothesized that these vocalizations have an important role in intra-specific communication. Recently, we demonstrated that playback of 50-kHz ultrasonic vocalizations can induce social approach, indicating that 50-kHz calls can serve to (re)establish or to maintain social contact. It is known that endogenous opioids are implicated in the regulation of social behavior, particularly in rough and tumble play. Here, we tested whether administration of opioid ligands can affect social approach in response to playback of 50-kHz calls in juvenile and adult rats. Rats were either treated with 1mg/kg naloxone, 1mg/kg morphine, or with saline vehicle. Administration of opioid ligands affected social approach at both ages. Specifically, in juvenile and adult rats, social approach displayed in response to playback of 50-kHz calls was reduced in case of naloxone treatment, but enhanced with morphine. Furthermore, juvenile rats treated with saline or morphine emitted a substantial amount of ultrasonic vocalizations in response to the playback of 50-kHz calls. Such ultrasonic calling was not seen in naloxone treated rats. Importantly, these drug-dependent differences were stimulus-specific, i.e. seen only in response to playback of 50-kHz calls and not in response to playback of background noise. The present finding that opioid ligands can affect social approach and ultrasonic vocalizations induced by playback of 50-kHz calls, indicates that an important feature of social interaction in rats, namely ultrasonic communication, is at least partially regulated by endogenous opioids.

  10. HIGHER FREQUENCY ULTRASONIC LIGHT MODULATORS.

    Science.gov (United States)

    LIGHT), (* MODULATORS , (*ULTRASONIC RADIATION, MODULATORS ), OPTICAL COMMUNICATIONS, BANDWIDTH, TRANSDUCERS, HIGH FREQUENCY, VERY HIGH FREQUENCY, ATTENUATION, DATA PROCESSING, OPTICAL EQUIPMENT, ANALOG COMPUTERS, THEORY.

  11. ION EXCHANGE-ULTRASONIC WAVE JOINT PRODUCTION OF NANOSCALE PURE MOLYBDENUM TRIOXIDE PROCESS%离子交换-超声波联合生产纳米级纯三氧化钼工艺初探

    Institute of Scientific and Technical Information of China (English)

    樊建军

    2016-01-01

    With sodium molybdate solution ( containing molybdenum 10 to 50 g/L) which is the desorbed solution got from ammonium molybdate pickling waste water after recycling molybdenum as raw material ,molybdic acid was obtained by cation exchange ,nanoscale pure molybdenum trioxide was got by treating molybdic acid with ultrasonic wave.Process parameters have great influence on the purity of nanoscale pure molybdenum trioxide ,grain size ,crystal shape.%本文以钼酸铵酸洗废水回收钼后的解析液——钼酸钠溶液(含钼10~50 g/L)为原料,采用阳离子交换得到钼酸溶液,通过超声波对钼酸溶液进行处理得到纳米级纯三氧化钼,过程工艺参数对纳米级纯三氧化钼的纯度、粒度、晶形等有重要影响.

  12. Wireless Communication with a Microprocessor Based Ultrasonic Meter for Flow Measurements

    Directory of Open Access Journals (Sweden)

    Mahmoud Z. Iskandarani

    2009-01-01

    Full Text Available Problem statement: Although the traditional metering system and method for controlling flow is generally safe, reliable and robust, it does suffer certain drawbacks, such as limited accuracy and the ability to implement complex reactive rate designs. Hence, there is a need for a circuit and method of increasing metering accuracy, as well as the position control accuracy for variable flow rates, without further reliance on mechanical tolerances. An essential component for an electronic meter is a database and method of communication to obtain the required measurements and to program the meter for any additional needed values. Flexibility is added to such meters by using wireless communication circuits and protocols, which will enable reading of multi-devices from the same source point. Approach: To collect data, critical quality of service and carry out analysis, wireless flow meter reading system is designed, tested and implemented. The hardware and software in the designed system work together, to wirelessly receive readings from meters and then process it in order to obtain an accurate reading for the measured flow. The system makes use of modern communication algorithms and techniques. Also, the system allows for history tracing and analysis. The interfacing hardware uses two-way wireless optical interface to flow meter device. Results: The Hardware and Communication Protocol tested successfully and provided sufficient and accurate data for flow measurements analysis, presented in this research. Conclusion: Such hardware-software arrangement is considered a core for mobile meter reading and control with possibility to add intelligent security algorithms.

  13. Affiliative behavior, ultrasonic communication and social reward are influenced by genetic variation in adolescent mice.

    Directory of Open Access Journals (Sweden)

    Jules B Panksepp

    Full Text Available Social approach is crucial for establishing relationships among individuals. In rodents, social approach has been studied primarily within the context of behavioral phenomena related to sexual reproduction, such as mating, territory defense and parental care. However, many forms of social interaction occur before the onset of reproductive maturity, which suggests that some processes underlying social approach among juvenile animals are probably distinct from those in adults. We conducted a longitudinal study of social investigation (SI in mice from two inbred strains to assess the extent to which genetic factors influence the motivation for young mice to approach one another. Early-adolescent C57BL/6J (B6 mice, tested 4-6 days after weaning, investigated former cage mates to a greater degree than BALB/cJ (BALB mice, irrespective of the sex composition within an interacting pair. This strain difference was not due to variation in maternal care, the phenotypic characteristics of stimulus mice or sensitivity to the length of isolation prior to testing, nor was it attributable to a general difference in appetitive motivation. Ultrasonic vocalization (USV production was positively correlated with the SI responses of mice from both strains. Interestingly, several USV characteristics segregated with the genetic background of young mice, including a higher average frequency and shorter duration for the USVs emitted by B6 mice. An assessment of conditioned place preference responses indicated that there was a strain-dependent difference in the rewarding nature of social contact. As adolescent mice aged, SI responses gradually became less sensitive to genetic background and more responsive to the particular sex of individuals within an interacting pair. We have thus identified a specific, genetic influence on the motivation of early-adolescent mice to approach one another. Consistent with classical theories of motivation, which propose a functional

  14. The Communication of "Pure" Group-Based Anger Reduces Tendencies Toward Intergroup Conflict Because It Increases Out-Group Empathy

    NARCIS (Netherlands)

    de Vos, Bart; van Zomeren, Martijn; Gordijn, Ernestine H.; Postmes, Tom

    2013-01-01

    The communication of group-based anger in intergroup conflict is often associated with destructive conflict behavior. However, we show that communicating group-based anger toward the out-group can evoke empathy and thus reduce intergroup conflict. This is because it stresses the value of maintaining

  15. The Communication of "Pure" Group-Based Anger Reduces Tendencies Toward Intergroup Conflict Because It Increases Out-Group Empathy

    NARCIS (Netherlands)

    de Vos, Bart; van Zomeren, Martijn; Gordijn, Ernestine H.; Postmes, Tom

    2013-01-01

    The communication of group-based anger in intergroup conflict is often associated with destructive conflict behavior. However, we show that communicating group-based anger toward the out-group can evoke empathy and thus reduce intergroup conflict. This is because it stresses the value of maintaining

  16. Working in a developing communication space. Facebook and Twitter as journalistic tools for European information pure-player websites

    Directory of Open Access Journals (Sweden)

    Florian Tixier

    2014-06-01

    Full Text Available Since the creation of the European Union, European information has been a very important issue of communication. Numerous Europe-specialized information websites were born in the first decade of the 21st century, thus creating a European informational landscape on the Internet. In a context of journalistic technological and economical evolutions, journalists have to adapt rapidly their ways of working. A new function in terms of management of socio-numeric networks has appeared: community management. This research aims at analyzing the uses of Facebook and Twitter in the community management of online European information websites. We will be specifically observing how information makers integrate these technologies, which originally were not part of the journalistic work patterns, and how they use these new means of communication to circulate European ideas through self-promotion practices.

  17. WORKING IN A DEVELOPING COMMUNICATION SPACE. FACEBOOK AND TWITTER AS JOURNALISTIC TOOLS FOR EUROPEAN INFORMATION PURE-PLAYER WEBSITES

    Directory of Open Access Journals (Sweden)

    Florian Tixier

    2014-06-01

    Full Text Available Since the creation of the European Union, European information has been a very important issue of communication. Numerous Europe-specialized information websites were born in the first decade of the 21st century, thus creating a European informational landscape on the Internet. In a context of journalistic technological and economical evolutions, journalists have to adapt rapidly their ways of working. A new function in terms of management of socio-numeric networks has appeared: community management. This research aims at analyzing the uses of Facebook and Twitter in the community management of online European information websites. We will be specifically observing how information makers integrate these technologies, which originally were not part of the journalistic work patterns, and how they use these new means of communication to circulate European ideas through self-promotion practices.

  18. Communication: A method to compute the transport coefficient of pure fluids diffusing through planar interfaces from equilibrium molecular dynamics simulations

    Science.gov (United States)

    Vermorel, Romain; Oulebsir, Fouad; Galliero, Guillaume

    2017-09-01

    The computation of diffusion coefficients in molecular systems ranks among the most useful applications of equilibrium molecular dynamics simulations. However, when dealing with the problem of fluid diffusion through vanishingly thin interfaces, classical techniques are not applicable. This is because the volume of space in which molecules diffuse is ill-defined. In such conditions, non-equilibrium techniques allow for the computation of transport coefficients per unit interface width, but their weak point lies in their inability to isolate the contribution of the different physical mechanisms prone to impact the flux of permeating molecules. In this work, we propose a simple and accurate method to compute the diffusional transport coefficient of a pure fluid through a planar interface from equilibrium molecular dynamics simulations, in the form of a diffusion coefficient per unit interface width. In order to demonstrate its validity and accuracy, we apply our method to the case study of a dilute gas diffusing through a smoothly repulsive single-layer porous solid. We believe this complementary technique can benefit to the interpretation of the results obtained on single-layer membranes by means of complex non-equilibrium methods.

  19. Ultrasonic physics

    CERN Document Server

    Richardson, E G

    1962-01-01

    Ultrasonic Physics, Second Edition, provides an introduction to the fundamental principles of ultrasonic physics. The book opens with a discussion of the sources of ultrasound. This is followed by separate chapters on the properties and detection of ultrasonic radiation; measurement of propagation constants, i.e., the velocity and absorption, of ultrasound; ultrasound propagation in gases, liquids, and solids; and ultrasound propagation in aerosols, suspensions, and emulsions. The final chapter covers miscellaneous physical and physico-chemical actions, including dispersion and coagulation of

  20. Ultrasonic Motors

    Science.gov (United States)

    2003-06-01

    and T. Higuchi, "Cylindrical Micro Ultrasonic Motor Utilizing Bulk Lead Zirconate Titanate (PZT)," Japanese Journal of Applied Physics Part 1-Regular Papers Short Notes & Review Papers, vol. 38, pp. 3347-3350, 1999.

  1. 超声波穿金属厚壁通信电路系统设计与实现%Design and Implementation of Ultrasonic Through-metal-thick-wall Communication Circuit System

    Institute of Scientific and Technical Information of China (English)

    李海廷; 杨涛

    2013-01-01

    A novel ultrasonic high voltage pulse transmitting circuit based on a energy storage inductance was presented after analyzing ultrasonic through-metal-thick-wall communication system that needs high frequency and high voltage. The control signal based on FPGA drived IGBT switch component with high precision and frequency. The receiving signal amplifier and bandpass filtering circuit were designed to achieve the stability of the ultrasonic receiving signal after analyzing the ultrasonic transmission condition in the medium interface. Data flows were restored based on FPGA after ultrasonic signal envelope detection and A/D sampling. The design scheme has important potential applications which realizes the information collection and transmission with high speed in sealed containers.%在分析超声波穿金属厚壁通信系统需要高频高压的基础上,设计了一种利用电感储能产生高压脉冲的发射电路.采用FPGA产生高精度高频控制信号,驱动IGBT开关元件.同时在对介质表面声波透射状况分析后,设计了接收信号放大和带通滤波电路,实现了超声信号的稳定接收.在接收信号包络检波和A/D采样转换后,通过FPGA处理实现了数据流的还原.该设计方案可实现密闭容器内信息的采集与高速传输,具有重要的应用前景.

  2. Short communication: Jersey × Holstein crossbreds compared with pure Holsteins for production, mastitis, and body measurements during the first 3 lactations.

    Science.gov (United States)

    Heins, B J; Hansen, L B; Seykora, A J; Hazel, A R; Johnson, D G; Linn, J G

    2011-01-01

    Jersey (JE)×Holstein (HO) crossbred cows (n=76) were compared with pure HO cows (n=73) for 305-d milk, fat, and protein production, somatic cell score (SCS), clinical mastitis, lifetime production, and body measurements during their first 3 lactations. Cows were in 2 research herds at the University of Minnesota and calved from September 2003 to June 2008. Best prediction was used to determine actual production for 305-d lactations as well as lifetime production (to 1,220 d in the herd after first calving) from test-day observations. During first lactation, JE×HO cows and pure HO cows were not significantly different for fat plus protein production; however, JE×HO cows had significantly lower fat plus protein production during second (-25 kg) and third (-51 kg) lactation than pure HO cows. Nevertheless, JE×HO cows were not significantly different from pure HO cows for lifetime production or lifetime SCS. The JE×HO cows were not significantly different from pure HO cows for SCS and clinical mastitis during first and second lactations; however, JE×HO cows tended to have higher SCS (3.79) than pure HO cows (3.40), but significantly lower (-23.4%) clinical mastitis during third lactation. The JE×HO cows had significantly less hip height, smaller heart girth, less thurl width, and less pin width than pure HO cows during the first 3 lactations. Furthermore, JE×HO cows had significantly less udder clearance from the ground and significantly greater distance between the front teats than pure HO cows during their first 3 lactations. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  3. Ultrasonic Polishing

    Science.gov (United States)

    Gilmore, Randy

    1993-01-01

    The ultrasonic polishing process makes use of the high-frequency (ultrasonic) vibrations of an abradable tool which automatically conforms to the work piece and an abrasive slurry to finish surfaces and edges on complex, highly detailed, close tolerance cavities in materials from beryllium copper to carbide. Applications range from critical deburring of guidance system components to removing EDM recast layers from aircraft engine components to polishing molds for forming carbide cutting tool inserts or injection molding plastics. A variety of materials including tool steels, carbides, and even ceramics can be successfully processed. Since the abradable tool automatically conforms to the work piece geometry, the ultrasonic finishing method described offers a number of important benefits in finishing components with complex geometries.

  4. Ultrasonic neuromodulation

    Science.gov (United States)

    Naor, Omer; Krupa, Steve; Shoham, Shy

    2016-06-01

    Ultrasonic waves can be non-invasively steered and focused into mm-scale regions across the human body and brain, and their application in generating controlled artificial modulation of neuronal activity could therefore potentially have profound implications for neural science and engineering. Ultrasonic neuro-modulation phenomena were experimentally observed and studied for nearly a century, with recent discoveries on direct neural excitation and suppression sparking a new wave of investigations in models ranging from rodents to humans. In this paper we review the physics, engineering and scientific aspects of ultrasonic fields, their control in both space and time, and their effect on neuronal activity, including a survey of both the field’s foundational history and of recent findings. We describe key constraints encountered in this field, as well as key engineering systems developed to surmount them. In closing, the state of the art is discussed, with an emphasis on emerging research and clinical directions.

  5. Ultrasonic vocalizations emitted by flying squirrels.

    Directory of Open Access Journals (Sweden)

    Meghan N Murrant

    Full Text Available Anecdotal reports of ultrasound use by flying squirrels have existed for decades, yet there has been little detailed analysis of their vocalizations. Here we demonstrate that two species of flying squirrel emit ultrasonic vocalizations. We recorded vocalizations from northern (Glaucomys sabrinus and southern (G. volans flying squirrels calling in both the laboratory and at a field site in central Ontario, Canada. We demonstrate that flying squirrels produce ultrasonic emissions through recorded bursts of broadband noise and time-frequency structured frequency modulated (FM vocalizations, some of which were purely ultrasonic. Squirrels emitted three types of ultrasonic calls in laboratory recordings and one type in the field. The variety of signals that were recorded suggest that flying squirrels may use ultrasonic vocalizations to transfer information. Thus, vocalizations may be an important, although still poorly understood, aspect of flying squirrel social biology.

  6. Ultrasonic Inspection

    Science.gov (United States)

    1976-01-01

    Automation Industries Inc. has had more than $2 million in contracts to produce innovative equipment for the Apollo program. When Marshall Space Flight Center sought a fast nondestructive way to inspect butt welds in aluminum alloys for spacecraft, the company developed a reliable ultrasonic device using multiple transducers called "delta manipulators" which detect lack of weld penetration not readily seen in radiograph automation. Industry soon adapted the ultrasonic equipment to a unique rail inspection device that saves countless man hours. Device is contained in self propelled railroad cars produced and operated by the company to check old track welds for deterioration.

  7. 魏晋清谈对口语交际教学目标取向的启示%The Inspirations of Wei - Jin Pure Talk on Oral Communication Teaching Goal-orientation

    Institute of Scientific and Technical Information of China (English)

    蒋宇娇

    2016-01-01

    Teaching has long been neglected oral communication caused no history of oral communication teaching empirical evidence may refer to the situation. In the context of globalization, countries native language educational experiences influence each other, learn from each other, but just far enough nutrition learn from foreign experience teaching development of oral communication. Chinese oral communication teaching to obtain long-term development will have to go back to the ancient culture to absorb nutrients and get inspira⁃tion, such as Wei - Jin pure talk. Identify the" Wei - Jin pure talk in terms of oral communication objectives orientation" and"new standard oral communication teaching goal orientation" meeting point between these two, may help locate contemporary oral communi⁃cation teaching goal-oriented.%长期以来对口语交际教学的忽视造成了我国口语交际教学无历史实证依据可资参考的局面。在全球化的背景下,各国母语教育经验相互影响、相互借鉴,但仅仅是借鉴国外经验远远不够。中国口语交际教学要获得长足发展还得回到古代文化中去汲取营养,比如魏晋清谈。找准“魏晋清谈在口语交际方面的目标取向”和“新课标口语交际教学的目标取向”这二者之间的契合点,或许有助于当代口语交际教学目标取向的定位。

  8. Communication

    NARCIS (Netherlands)

    Sigafoos, J.; Lancioni, G.E.; O'Reilly, M.F.; Lang, R.; Singh, N.N.; Didden, H.C.M.; Green, V.A.; Marschik, P.B.

    2016-01-01

    Communication disorders are common among people with intellectual disabilities. Consequently, enhancing the communication skills of such individuals is a major intervention priority. This chapter reviews the nature and prevalence of the speech, language, and communication problems associated with

  9. Application of ultrasonic communication in rodent management and control%鼠类超声通讯在鼠害防治中的应用

    Institute of Scientific and Technical Information of China (English)

    陈毅; 刘全生

    2016-01-01

    鼠类针对不同刺激或不同目的可发出超声波,且超声信号的频率和时程随年龄、性别、种类、自然和社会环境的不同而出现差异性变化,同时可接收超声波信号。该文介绍了鼠类超声信号的研究成果,并阐述当前超声波驱鼠器的使用状况及存在问题,为新型高效超声驱鼠产品的研发和使用提供建议,从而更好地开展鼠害防治工作。%Rodents emit and perceive calls in the ultrasonic range, i.e., above the human hearing threshold of about 20 kHz:so⁃called ultrasonic vocalizations(USV). They emit USV, which differ in frequencies and durations according to their age, sex, species, and the physical and social behaviors, in response to different stimuli and for different purposes. This paper describes the characteristics and functions of the USV in rodents, and also elaborates current status of ultrasonic rodent repellent devices. It is very important for the research and development of the new, efficient ultrasonic rodent deterrent devices.

  10. Ultrasonic transducer

    Science.gov (United States)

    Taylor, Steven C.; Kraft, Nancy C.

    2007-03-13

    An ultrasonic transducer having an effective center frequency of about 42 MHz; a bandwidth of greater than 85% at 6 dB; a spherical focus of at least 0.5 inches in water; an F4 lens; a resolution sufficient to be able to detect and separate a 0.005 inch flat-bottomed hole at 0.005 inches below surface; and a beam size of approximately 0.006–0.008 inches measured off a 11/2 mm ball in water at the transducer's focal point.

  11. Application of nurse-patient communication for triage work in the ultrasonic department%护患沟通在超声科分诊工作中的应用

    Institute of Scientific and Technical Information of China (English)

    周琪

    2012-01-01

    Objective To explore the effect of nurse - patient communication for triage work in the ultrasonic department. Methods The causes and countermeasures for the nurse - patient disputes were retrospectively summarized. The nurses of triage updated the awareness of positive service to the patients,commanded the communication skills and applied flexibly to clinical practice. Therefore,a favorable nurse - patient relationship was established. Results Favorable communication skills promoted the nurse - patient relationship,reduced the nurse - patient disputes,and improved the patients' satisfactoriness. Conclusion The application of favorable communication skills is able to enhance nurse - patient affiliation ability,avoid the nurse - patient disputes and elevate quality of care.%目的 探讨护患沟通在超声科分诊工作中的应用效果.方法 对护患纠纷发生的原因及防范对策进行回顾总结.分诊护士通过更新观念,加强主动服务意识,掌握护患沟通技巧,并灵活应用于临床工作实践中,建立良好的护患关系.结果 增进护患关系,减少护患纠纷,提高患者满意度.结论 应用良好的沟通技巧,可以增强护患之间的亲和力,避免护患纠纷,提高护理质量.

  12. Ultrasonic Device for Assessing the Quality of a Wire Crimp

    Science.gov (United States)

    Yost, William T. (Inventor); Perey, Daniel F. (Inventor); Cramer, Karl E. (Inventor)

    2015-01-01

    A system for determining the quality of an electrical wire crimp between a wire and ferrule includes an ultrasonically equipped crimp tool (UECT) configured to transmit an ultrasonic acoustic wave through a wire and ferrule, and a signal processor in communication with the UECT. The signal processor includes a signal transmitting module configured to transmit the ultrasonic acoustic wave via an ultrasonic transducer, signal receiving module configured to receive the ultrasonic acoustic wave after it passes through the wire and ferrule, and a signal analysis module configured to identify signal differences between the ultrasonic waves. The signal analysis module is then configured to compare the signal differences attributable to the wire crimp to a baseline, and to provide an output signal if the signal differences deviate from the baseline.

  13. Ultrasonic Determination Of Recrystallization

    Science.gov (United States)

    Generazio, Edward R.

    1988-01-01

    State of recrystallization identified. Measurement of ultrasonic attenuation shows promise as means of detecting recrystallization in metal. Technique applicable to real-time acoustic monitoring of thermomechanical treatments. Starting with work-hardened material, one ultrasonically determines effect of annealing, using correlation between ultrasonic attenuation and temperature.

  14. Ultrasonic colour Doppler imaging

    DEFF Research Database (Denmark)

    Evans, David H.; Jensen, Jørgen Arendt; Nielsen, Michael Bachmann

    2011-01-01

    Ultrasonic colour Doppler is an imaging technique that combines anatomical information derived using ultrasonic pulse-echo techniques with velocity information derived using ultrasonic Doppler techniques to generate colour-coded maps of tissue velocity superimposed on grey-scale images of tissue ...

  15. Communications

    Science.gov (United States)

    Bailenson, Jeremy; Buzzanell, Patrice; Deetz, Stanley; Tewksbury, David; Thompson, Robert J.; Turow, Joseph; Bichelmeyer, Barbara; Bishop, M. J.; Gayeski, Diane

    2013-01-01

    Scholars representing the field of communications were asked to identify what they considered to be the most exciting and imaginative work currently being done in their field, as well as how that work might change our understanding. The scholars included Jeremy Bailenson, Patrice Buzzanell, Stanley Deetz, David Tewksbury, Robert J. Thompson, and…

  16. Sixth form pure mathematics

    CERN Document Server

    Plumpton, C

    1968-01-01

    Sixth Form Pure Mathematics, Volume 1, Second Edition, is the first of a series of volumes on Pure Mathematics and Theoretical Mechanics for Sixth Form students whose aim is entrance into British and Commonwealth Universities or Technical Colleges. A knowledge of Pure Mathematics up to G.C.E. O-level is assumed and the subject is developed by a concentric treatment in which each new topic is used to illustrate ideas already treated. The major topics of Algebra, Calculus, Coordinate Geometry, and Trigonometry are developed together. This volume covers most of the Pure Mathematics required for t

  17. Female frogs send ultrasonic signals for courtship

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ During their studies of Odorrana tormota,a frog species with recessed tympanic membranes,CAS researchers have found that females go ultrasonic during courtship,revealing an amazingly system for communication.The work was reported online on 8 May by Nature.

  18. Tracking Frogs that sing ultrasonic duet

    Institute of Scientific and Technical Information of China (English)

    XIN Ling

    2009-01-01

    @@ In central China, unique frogs talk by emitting ultrasonic calls, male to show their virility and female for courtship, which are received by tunable ears with amazing accuracy. Prof. SHEN Junxian from the CAS Institute of Biophysics and his collaborators are working diligently to explore the mysteries of unique sound communication in animal kingdom.

  19. Ultrasonic Microtransport

    Science.gov (United States)

    Moroney, Richard Morgan, III

    We have observed numerous kinetic effects using ultrasonic flexural plate waves (FPWs) in 4mu -thick composite plates of low-stress silicon nitride, piezoelectric zinc oxide and aluminum. The wavelength is typically 100 mum, and the area 3 x 8 mm^2. A successful new surface micromachining fabrication process is presented here for the first time. FPWs have been used to move liquids and gasses with motion typically indicated by polysilicon blocks in air and polystyrene spheres in water; the velocity in air is 4.5 mm/s (with a zero-to-peak input of 3 V), and in water it is 100 mum/s (with an input of 7.8 V). Other observations include pumping of a liquid dye, and mixing near the FPW surface. All quantitative observations demonstrate that the kinetic effects of FPWs are proportional to the square of the wave amplitude. The amplitude for a typical device is 250 A at 9 V input; the power in a typical FPW is about 2 mW. The amplitude can be accurately measured using a laser diffraction technique. Experimental error is about +/-10%, and many of the results agree well with a simple theory to predict the FPW amplitude; extensions of the theory model the fluid loading of FPW devices, but experiment and theory disagree by about 15%. Pumping by flexural plate waves is an example of the phenomenon known as acoustic streaming. A common solution approach is the method of successive approximations, where the nonlinear equations are first linearized and solved. This "first-order" solution is then used to determine the inhomogeneous source terms in the linearized, "second -order" equations of motion. Theoretical predictions of streaming theory are in excellent agreement with experiment in the case where the FPW device contacts a half-space of fluid; predictions for flow in small channels encourage the development of integrated micropumps. Applications for microflow include thermal redistribution in integrated circuits and liquid movement in analytical instruments--particularly where

  20. On the importance of PURE - Public Understanding of Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    Broman, Lars; Kandpal, Tara C.

    2013-09-15

    Public understanding of science (PUS) is a central concept among science communicators. Public understanding of renewable energy (PURE) is proposed as an important sub-concept of PUS. The aim of this paper is to interest and invite renewable energy scientists to join a PURE research project. Four separate important questions for a PURE research project can be identified: (A) Is PURE important? (B) Which issues of PURE are the most important ones, according to renewable energy scientists? (C) What understanding of renewable energy has the general public today, worldwide? (D) How to achieve PURE?.

  1. Preparation of ZnO nanocrystals via ultrasonic irradiation

    DEFF Research Database (Denmark)

    Qian, D.; Jiang, Jianzhong; Hansen, P. L.

    2003-01-01

    A simple and rapid process has been developed for the preparation of nanometer-sized ZnO crystals via ultrasonic irradiation, by which pure ZnO nanocrystals with an average size of 6 nm and narrow size distribution can be synthesized in a short time and without using any solvents for the precipit......A simple and rapid process has been developed for the preparation of nanometer-sized ZnO crystals via ultrasonic irradiation, by which pure ZnO nanocrystals with an average size of 6 nm and narrow size distribution can be synthesized in a short time and without using any solvents...

  2. Polarization-dependent optical reflection ultrasonic detection

    Science.gov (United States)

    Zhu, Xiaoyi; Huang, Zhiyu; Wang, Guohe; Li, Wenzhao; Li, Changhui

    2017-03-01

    Although ultrasound transducers based on commercial piezoelectric-material have been widely used, they generally have limited bandwidth centered at the resonant frequency. Currently, several pure-optical ultrasonic detection methods have gained increasing interest due to their wide bandwidth and high sensitivity. However, most of them require customized components (such as micro-ring, SPR, Fabry-Perot film, etc), which limit their broad implementations. In this study, we presented a simple pure-optical ultrasound detection method, called "Polarization-dependent Reflection Ultrasonic Detection" (PRUD). It detects the intensity difference between two polarization components of the probe beam that is modulated by ultrasound waves. PRUD detect the two components by using a balanced detector, which effectively suppressed much of the unwanted noise. We have achieved the sensitivity (noise equivalent pressure) to be 1.7kPa, and this can be further improved. In addition, like many other pure-optical ultrasonic detection methods, PRUD also has a flat and broad bandwidth from almost zero to over 100MHz. Besides theoretical analysis, we did a phantom study by imaging a tungsten filament to demonstrate the performance of PRUD. We believe this simple and economic method will attract both researchers and engineers in optical and ultrasound fields.

  3. COMMUNICATIONS

    CERN Document Server

    A. Petrilli

    2013-01-01

    The organisation of the Open Days at the end of September was the single biggest effort of the CMS Communications Group this year. We would like to thank all volunteers for their hard work to show our Point 5 facilities and explain science and technology to the general public. During two days more than 5,000 people visited the CMS detector underground and profited from the surface activities, which included an exhibition on CMS, a workshop on superconductivity, and an activity for our younger visitors involving wooden Kapla blocks. The Communications Group took advantage of the preparations to produce new CMS posters that can be reused at other venues. Event display images have been produced not just for this occasion but also for other exhibits, education purposes, publications etc. During the Open Days, Gilles Jobin, 2012 winner of CERN Collide@CERN prize, performed his Quantum show in Point 5, with the light installation of German artist Julius von Bismarck. Image 3: CERN Open Days at CMS wel...

  4. COMMUNICATIONS

    CERN Multimedia

    L. Taylor and D. Barney

    2010-01-01

    CMS Centres, Outreach and the 7 TeV Media Event The new CMS Communications group is now established and is addressing three areas that are critical to CMS as it enters the physics operations phase: - Communications Infrastructure, including almost 50 CMS Centres Worldwide, videoconferencing systems, and CERN meeting rooms - Information systems, including the internal and external Web sites as well as the document preparation and management systems - Outreach and Education activities, including working with print, radio and TV media, visits to CMS, and exhibitions. The group has been active in many areas, with the highest priority being accorded to needs of CMS operations and preparations for the major media event planned for 7 TeV collisions. Unfortunately the CMS Centre@CERN suffered a major setback when, on 21st December, a cooling water pipe froze and burst on the floor above the CMS Centre main room. Water poured through the ceiling, flooding the floor and soaking some of the consoles, before e...

  5. Electromagnetic ultrasonic guided waves

    CERN Document Server

    Huang, Songling; Li, Weibin; Wang, Qing

    2016-01-01

    This book introduces the fundamental theory of electromagnetic ultrasonic guided waves, together with its applications. It includes the dispersion characteristics and matching theory of guided waves; the mechanism of production and theoretical model of electromagnetic ultrasonic guided waves; the effect mechanism between guided waves and defects; the simulation method for the entire process of electromagnetic ultrasonic guided wave propagation; electromagnetic ultrasonic thickness measurement; pipeline axial guided wave defect detection; and electromagnetic ultrasonic guided wave detection of gas pipeline cracks. This theory and findings on applications draw on the author’s intensive research over the past eight years. The book can be used for nondestructive testing technology and as an engineering reference work. The specific implementation of the electromagnetic ultrasonic guided wave system presented here will also be of value for other nondestructive test developers.

  6. Rehabilitation of pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think...... that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions like alexia severity, and associated deficits. Many patients reported to have pure alexia...... in the reviewed studies, have associated deficits like agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however...

  7. Rehabilitation of pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions like alexia severity, and associated deficits. Many patients reported to have pure alexia......Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think...... in the reviewed studies, have associated deficits like agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however...

  8. Hand Gesture Recognition Using Ultrasonic Waves

    KAUST Repository

    AlSharif, Mohammed Hussain

    2016-04-01

    Gesturing is a natural way of communication between people and is used in our everyday conversations. Hand gesture recognition systems are used in many applications in a wide variety of fields, such as mobile phone applications, smart TVs, video gaming, etc. With the advances in human-computer interaction technology, gesture recognition is becoming an active research area. There are two types of devices to detect gestures; contact based devices and contactless devices. Using ultrasonic waves for determining gestures is one of the ways that is employed in contactless devices. Hand gesture recognition utilizing ultrasonic waves will be the focus of this thesis work. This thesis presents a new method for detecting and classifying a predefined set of hand gestures using a single ultrasonic transmitter and a single ultrasonic receiver. This method uses a linear frequency modulated ultrasonic signal. The ultrasonic signal is designed to meet the project requirements such as the update rate, the range of detection, etc. Also, it needs to overcome hardware limitations such as the limited output power, transmitter, and receiver bandwidth, etc. The method can be adapted to other hardware setups. Gestures are identified based on two main features; range estimation of the moving hand and received signal strength (RSS). These two factors are estimated using two simple methods; channel impulse response (CIR) and cross correlation (CC) of the reflected ultrasonic signal from the gesturing hand. A customized simple hardware setup was used to classify a set of hand gestures with high accuracy. The detection and classification were done using methods of low computational cost. This makes the proposed method to have a great potential for the implementation in many devices including laptops and mobile phones. The predefined set of gestures can be used for many control applications.

  9. Moths are not silent, but whisper ultrasonic courtship songs

    DEFF Research Database (Denmark)

    Nakano, R; Takanashi, T; Fujii, T

    2009-01-01

    Ultrasonic hearing is widespread among moths, but very few moth species have been reported to produce ultrasounds for sexual communication. In those that do, the signals are intense and thus well matched for long distance communication. By contrast, males of the Asian corn borer moth (Crambidae......) were recently shown to whisper extremely low-intensity ultrasonic courtship songs close to females. Since low sound levels will prevent eavesdropping by predators, parasites and conspecific rivals, we predicted low intensity ultrasound communication to be widespread among moths. Here we tested 13...

  10. Ultrasonic Hot Embossing

    Directory of Open Access Journals (Sweden)

    Werner Karl Schomburg

    2011-05-01

    Full Text Available Ultrasonic hot embossing is a new process for fast and low-cost production of micro systems from polymer. Investment costs are on the order of 20.000 € and cycle times are a few seconds. Microstructures are fabricated on polymer foils and can be combined to three-dimensional systems by ultrasonic welding.

  11. Ultrasonic corona sensor study

    Science.gov (United States)

    Harrold, R. T.

    1976-01-01

    The overall objective of this program is to determine the feasibility of using ultrasonic (above 20 kHz) corona detection techniques to detect low order (non-arcing) coronas in varying degrees of vacuum within large high vacuum test chambers, and to design, fabricate, and deliver a prototype ultrasonic corona sensor.

  12. Ultrasonic flow meter

    NARCIS (Netherlands)

    Lötters, Joost Conrad; Snijders, G.J.; Volker, A.W.F.

    2014-01-01

    The invention relates to an ultrasonic flow meter comprising a flow tube for the fluid whose flow rate is to be determined. The flow meter comprises a transmitting element for emitting ultrasonic waves, which is provided on the outer jacket of the flow tube. A receiving element, which is provided on

  13. Schlieren visualization of ultrasonic standing waves in mm-sized chambers for ultrasonic particle manipulation

    OpenAIRE

    Möller, Dirk; Degen, Nicolas; Dual, Jurg

    2013-01-01

    Background For the design and characterization of ultrasonic particle manipulation devices the pressure field in the fluid cavity is of great interest. The schlieren method provides an optical tool for the visualization of such pressure fields. Due to its purely optical nature this experimental method has got some unique advantages compared to methods like particle tracking. Results A vertical schlieren setup and an investigation with the same of a mm-sized chamber used to agglomerate particl...

  14. Pure-tone Audiometer

    Science.gov (United States)

    Kapul, A. A.; Zubova, E. I.; Torgaev, S. N.; Drobchik, V. V.

    2017-08-01

    The research focuses on a pure-tone audiometer designing. The relevance of the study is proved by high incidence of an auditory analyser in older people and children. At first, the article provides information about subjective and objective audiometry methods. Secondly, we offer block-diagram and basic-circuit arrangement of device. We decided to base on STM32F407VG microcontroller and use digital pot in the function of attenuator. Third, we implemented microcontroller and PC connection. C programming language is used for microcontroller’s program and PC’s interface. Fourthly, we created the pure-tone audiometer prototype. In the future, we will implement the objective method ASSR in addition to pure-tone audiometry.

  15. Auto-positioning ultrasonic transducer system

    Science.gov (United States)

    Buchanan, Randy K. (Inventor)

    2010-01-01

    An ultrasonic transducer apparatus and process for determining the optimal transducer position for flow measurement along a conduit outer surface. The apparatus includes a transmitting transducer for transmitting an ultrasonic signal, said transducer affixed to a conduit outer surface; a guide rail attached to a receiving transducer for guiding movement of a receiving transducer along the conduit outer surface, wherein the receiving transducer receives an ultrasonic signal from the transmitting transducer and sends a signal to a data acquisition system; and a motor for moving the receiving transducer along the guide rail, wherein the motor is controlled by a controller. The method includes affixing a transmitting transducer to an outer surface of a conduit; moving a receiving transducer on the conduit outer surface, wherein the receiving transducer is moved along a guide rail by a motor; transmitting an ultrasonic signal from the transmitting transducer that is received by the receiving transducer; communicating the signal received by the receiving transducer to a data acquisition and control system; and repeating the moving, transmitting, and communicating along a length of the conduit.

  16. Pro-social 50-kHz ultrasonic communication in rats: Post-weaning but not post-adolescent social isolation leads to social impairments – phenotypic rescue by re-socialization

    Directory of Open Access Journals (Sweden)

    Dominik eSeffer

    2015-05-01

    Full Text Available Rats are highly social animals and social play during adolescence has an important role for social development, hence post-weaning social isolation is widely used to study the adverse effects of juvenile social deprivation and to induce behavioral phenotypes relevant to neuropsychiatric disorders, like schizophrenia. Communication is an important component of the rat’s social behavior repertoire, with ultrasonic vocalizations (USV serving as situation-dependent affective signals. High-frequency 50-kHz USV occur in appetitive situations and induce approach behavior, supporting the notion that they serve as social contact calls; however, post-weaning isolation effects on the behavioral changes displayed by the receiver in response to USV have yet to be studied. We therefore investigated the impact of post-weaning isolation on socio-affective information processing as assessed by means of our established 50-kHz USV radial maze playback paradigm. We showed that post-weaning social isolation specifically affected the behavioral response to playback of pro-social 50-kHz but not alarm 22-kHz USV. While group-housed rats showed the expected preference, i.e. approach, towards 50-kHz USV, the response was even stronger in short-term isolated rats (i.e. 1 day, possibly due to a higher level of social motivation. In contrast, no approach was observed in long-term isolated rats (i.e. 4 weeks. Importantly, deficits in approach were reversed by peer-mediated re-socialization and could not be observed after post-adolescent social isolation, indicating a critical period for social development during adolescence. Together, these results highlight the importance of social experience for affiliative behavior, suggesting a critical involvement of play behavior on socio-affective information processing in rats.

  17. Dahlbeck and Pure Ontology

    Science.gov (United States)

    Mackenzie, Jim

    2016-01-01

    This article responds to Johan Dahlbeck's "Towards a pure ontology: Children's bodies and morality" ["Educational Philosophy and Theory," vol. 46 (1), 2014, pp. 8-23 (EJ1026561)]. His arguments from Nietzsche and Spinoza do not carry the weight he supposes, and the conclusions he draws from them about pedagogy would be…

  18. Dahlbeck and Pure Ontology

    Science.gov (United States)

    Mackenzie, Jim

    2016-01-01

    This article responds to Johan Dahlbeck's "Towards a pure ontology: Children's bodies and morality" ["Educational Philosophy and Theory," vol. 46 (1), 2014, pp. 8-23 (EJ1026561)]. His arguments from Nietzsche and Spinoza do not carry the weight he supposes, and the conclusions he draws from them about pedagogy would be…

  19. Are all noisy quantum states obtained from pure ones?

    CERN Document Server

    Henderson, L; Popescu, S

    2001-01-01

    We ask what type of mixed quantum states can arise when a number of separated parties start by sharing a pure quantum state and then this pure state becomes contaminated by noise. We show that not all mixed states arise in this way. This is even the case if the separated parties actively try to degrade their initial pure state by arbitrary local actions and classical communication.

  20. Ultrasonic washing of textiles.

    Science.gov (United States)

    Choi, Junhee; Kim, Tae-Hong; Kim, Ho-Young; Kim, Wonjung

    2016-03-01

    We present the results of experimental investigation of ultrasonic washing of textiles. The results demonstrate that cavitation bubbles oscillating in acoustic fields are capable of removing soils from textiles. Since the washing performance is mitigated in a large washing bath when using an ultrasonic transducer, we propose a novel washing scheme by combining the ultrasonic vibration with a conventional washing method utilizing kinetic energy of textiles. It is shown that the hybrid washing scheme achieves a markedly enhanced performance up to 15% in comparison with the conventional washing machine. This work can contribute to developing a novel laundry machine with reduced washing time and waste water.

  1. Ultrasonic materials characterization

    Science.gov (United States)

    Smith, R. L.

    1987-02-01

    The National NDT Center at Harwell has been developing methods for the characterization of materials using ultrasonics. This paper reviews the progress made in applying ultrasonic attenuation measurements to the determination of such quantities as grain size and dislocation content. A method, ultrasonic attenuation spectral analysis, has been developed, which enables the contributions of scattering and absorption to the total attenuation to be separated. The theoretical advances that have been made are also described. Some of the practical applications of the technique are illustrated and future development discussed.

  2. Purely Functional Structured Programming

    OpenAIRE

    Obua, Steven

    2010-01-01

    The idea of functional programming has played a big role in shaping today's landscape of mainstream programming languages. Another concept that dominates the current programming style is Dijkstra's structured programming. Both concepts have been successfully married, for example in the programming language Scala. This paper proposes how the same can be achieved for structured programming and PURELY functional programming via the notion of LINEAR SCOPE. One advantage of this proposal is that m...

  3. Purely Cortical Anaplastic Ependymoma

    Directory of Open Access Journals (Sweden)

    Flávio Ramalho Romero

    2012-01-01

    Full Text Available Ependymomas are glial tumors derived from ependymal cells lining the ventricles and the central canal of the spinal cord. It may occur outside the ventricular structures, representing the extraventicular form, or without any relationship of ventricular system, called ectopic ependymona. Less than fifteen cases of ectopic ependymomas were reported and less than five were anaplastic. We report a rare case of pure cortical ectopic anaplastic ependymoma.

  4. Purely tetrahedral quadruple systems

    Institute of Scientific and Technical Information of China (English)

    JI Lijun

    2006-01-01

    An oriented tetrahedron is a set of four vertices and four cyclic triples with the property that any ordered pair of vertices is contained in exactly one of the cyclic triples. A tetrahedral quadruple system of order n (briefly TQS(n)) is a pair (X,B), where X is an nelement set and B is a set of oriented tetrahedra such that every cyclic triple on X is contained in a unique member of B. A TQS(n) (X, B) is pure if there do not exist two oriented tetrahedra with the same vertex set. In this paper, we show that there is a pure TQS(n) if and only if n≡2,4(mod 6),n>4,or n≡1,5(mod 12). One corollary is that there is a simple two-fold quadruple system of order n if and only if n≡2,4 (mod 6) and n>4, or n≡1, 5 (mod 12).Another corollary is that there is an overlarge set of pure Mendelsohn triple systems of order n for n≡1,3(mod 6),n>3, or n≡0,4 (mod 12).

  5. Fundamentals of Medical Ultrasonics

    CERN Document Server

    Postema, Michiel

    2011-01-01

    This book sets out the physical and engineering principles of acoustics and ultrasound as used for medical applications. It covers the basics of linear acoustics, wave propagation, non-linear acoustics, acoustic properties of tissue, transducer components, and ultrasonic imaging modes, as well as the most common diagnostic and therapeutic applications. It offers students and professionals in medical physics and engineering a detailed overview of the technical aspects of medical ultrasonic imaging, whilst serving as a reference for clinical and research staff.

  6. Metalworking with ultrasonic energy

    Science.gov (United States)

    Sonea, I.; Minca, M.

    1974-01-01

    The application of ultrasonic radiation for metal working of steel is discussed. It is stated that the productivity of the ultrasonic working is affected by the hardness of the material to be worked, the oscillation amplitude, the abrasive temperature, and the grain size. The factors that contribute to an increase in the dislocation speed are analyzed. Experimental data are provided to substantiate the theoretical parameters.

  7. ULTRASONIC ASSEMBLY [REVIEW

    Directory of Open Access Journals (Sweden)

    PORAV Viorica

    2015-05-01

    Full Text Available The paper exposes the possibility of machine producesers to optimize the costs of clothes assembling. Ultrasonic systems being frequently utilized have many advantages on semi products of synthetic textile and technical textile. First of all, sewing – cutting process can be accomplished under high speeds and rate of losses can be minimized. Cutting seal applications are frequently used for underwear and sportswear. Slicing and unit cutting machines, as well as portable sealing machines are available for labeling sector. Products such as bag, pocket and cover can be sewed in a seamless manner for promotion purposes. All objects in terms of accessories are obtained in same standard. Our quilting machines are preferred in worldwide due to its threadless, high quality sealing. An alternative to the classic sewing assembly, with thread and needles is ultrasonic seaming. In ultrasonic welding, there are no connective bolts, nails, soldering materials, or adhesives necessary to bind the materials together. Ultrasonic is defined as acoustic frequencies above the range audible to the human ear. Ultrasonic frequencies are administered to the fabric from the sonotrode of bonding machine. The high frequency and powerful energy produced, when is release in one special environment, the ultrasound heating this environment. The ability to ultrasonic weld textiles and films depend on their thermoplastic contents and the desired end results. The paper defines the weld ability of more common textiles and films. The welding refers to all types of bonding and sealing, as in point bonding of fabric, or continuous sealing of film.

  8. Ultrasonic processing of materials

    Energy Technology Data Exchange (ETDEWEB)

    Han, Q.; Sklad, P.S. [Oak Ridge National Laboratory, Oak Ridge, TN (United States)

    2007-07-01

    In some widely used alloys, dissolved gas precipitates form from liquids during solidification and form pores among solid dendrites and grains. The pores can lead to defects in aluminum shape casting. Research has suggested that ultrasonic vibrations have the potential to reduce the impurities present in traditional degassing methods. This paper summarized the results of several projects investigating the use of high intensity ultrasonic vibrations for material processing. The mechanisms of grain refining using high-intensity ultrasonic vibration were also investigated. High intensity ultrasonic vibrations were tested for the degassing of molten aluminum, grain refinement of alloys for industrial applications, and the modification of welding structures. Results of the studies to date have demonstrated that power ultrasound can be used to degas molten metal as well as for the grain refinement of alloys during solidification processes. Tests have demonstrated that the best grain refining effect was achieved when ultrasonic vibrations were introduced in the molten alloy at approximately 10 degrees C higher than the liquid temperature. The process is also suitable for improving the microstructure of steel weldments, as the process can modify the size and morphology of the primary phase and the secondary phases during the solidification of the alloy. Small and spherical grains in the size range of 30 {delta}m were obtained in aluminum A356 alloys. It was concluded that the benefits of ultrasonic vibrations on the alloy process were more pronounced in smaller specimens. 13 refs., 10 figs.

  9. Dispersion Method Using Focused Ultrasonic Field

    Science.gov (United States)

    Kim, Jungsoon; Kim, Moojoon; Ha, Kanglyel; Chu, Minchul

    2010-07-01

    The dispersion of powders into liquids has become one of the most important techniques in high-tech industries and it is a common process in the formulation of various products, such as paint, ink, shampoo, beverages, and polishing media. In this study, an ultrasonic system with a cylindrical transducer is newly introduced for pure nanoparticle dispersion. The acoustics pressure field and the characteristics of the shock pulse caused by cavitation are investigated. The frequency spectrum of the pulse from the collapse of air bubbles in the cavitation is analyzed theoretically. It was confirmed that a TiO2 water suspension can be dispersed effectively using the suggested system.

  10. Computations of Ultrasonic Parameters in Zr−Sn Alloys

    Directory of Open Access Journals (Sweden)

    Pramod Kumar Yadawa

    2011-01-01

    Full Text Available The ultrasonic properties like ultrasonic attenuation, sound velocity in the hexagonal Zr100−Sn alloys have been studied along unique axis at room temperature. The second- and third-order elastic constants (SOEC & TOEC have been calculated for these alloys using Lennard-Jones potential. The velocities and 1 have minima and maxima, respectively, at 45° with unique axis of the crystal, while 2 increases with the angle from unique axis. The inconsistent behaviour of angle-dependent velocities is associated to the action of second-order elastic constants. Debye average sound velocities of these alloys are increasing with the angle and has maximum at 55° with unique axis at room temperature. Hence, when a sound wave travels at 55° with unique axis of these alloys, then the average sound velocity is found to be maximum. The mechanical and ultrasonic properties of these alloys will be better than pure Zr and Sn due to their high SOEC and ultrasonic velocity and low ultrasonic attenuation. The comparison of calculated ultrasonic parameters with available theoretical/experimental physical parameters gives information about classification of these alloys.

  11. Ozone production in a dielectric barrier discharge with ultrasonic irradiation

    DEFF Research Database (Denmark)

    Drews, Joanna Maria; Kusano, Yukihiro; Leipold, Frank

    2011-01-01

    Ozone production has been investigated using an atmospheric pressure dielectric barrier discharge in pure O2 at room temperature with and without ultrasonic irradiation. It was driven at a frequency of either 15 kHz or 40 kHz. The ozone production was highly dependent on the O2 flow rate...... and the discharge power. Furthermore, powerful ultrasonic irradiation at a fundamental frequency of 30 kHz with the sound pressure level of 150 dB into the discharge can improve the ozone production efficiency, particularly when operated at the frequency of 15 kHz at the flow rate of 15 L/min....

  12. Porous silicon nanoparticles as sensitizers for ultrasonic hyperthermia

    Energy Technology Data Exchange (ETDEWEB)

    Sviridov, A. P., E-mail: asagittarius89@gmail.com; Andreev, V. G.; Ivanova, E. M.; Osminkina, L. A.; Tamarov, K. P.; Timoshenko, V. Yu. [Faculty of Physics, M.V. Lomonosov Moscow State University, 119991 Moscow (Russian Federation)

    2013-11-04

    Aqueous suspensions of porous silicon nanoparticles (NPs) with average size ∼100 nm and concentration ∼1 g/L undergo significant heating as compared with pure water under therapeutic ultrasonic (US) irradiation with frequencies of 1–2.5 MHz and intensities of 1–20 W/cm{sup 2}. This effect is explained by taking into account the efficient absorption of US energy by NPs. The observed US-induced heating of biodegradable NPs is promising for applications in ultrasonic hyperthermia of tumors.

  13. PURE DRIVE GT

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    在2004年奥林匹克赛事中,中国的李婷,孙甜甜取得了中国网球第一个金牌一女子双打冠军。忘记不了当时李婷挥动着她的BABOLAT(百保力)网拍Pure Drive Zylon 360°激动地拥抱着孙甜甜吵闹着,幸福地哭着的情景。

  14. Pure de Sitter Supergravity

    CERN Document Server

    Bergshoeff, Eric A; Kallosh, Renata; Van Proeyen, Antoine

    2015-01-01

    Using superconformal methods we derive an explicit de Sitter supergravity action invariant under spontaneously broken local ${\\cal N}=1$ supersymmetry. The supergravity multiplet interacts with a nilpotent goldstino multiplet. We present a complete locally supersymmetric action including the graviton and the fermionic fields, gravitino and goldstino, no scalars. In the global limit when supergravity multiplet decouples, our action reproduces the Volkov-Akulov theory. In the unitary gauge where goldstino vanishes we recover pure supergravity with the positive cosmological constant. The classical equations of motion, with all fermions vanishing, have a maximally symmetric solution: de Sitter space.

  15. Ultrasonics in Dentistry

    Science.gov (United States)

    Walmsley, A. D.

    Ultrasonic instruments have been used in dentistry since the 1950's. Initially they were used to cut teeth but very quickly they became established as an ultrasonic scaler which was used to remove deposits from the hard tissues of the tooth. This enabled the soft tissues around the tooth to return to health. The ultrasonic vibrations are generated in a thin metal probe and it is the working tip that is the active component of the instrument. Scanning laser vibrometry has shown that there is much variability in their movement which is related to the shape and cross sectional shape of the probe. The working instrument will also generate cavitation and microstreaming in the associated cooling water. This can be mapped out along the length of the instrument indicating which are the active areas. Ultrasonics has also found use for cleaning often inaccessible or different surfaces including root canal treatment and dental titanium implants. The use of ultrasonics to cut bone during different surgical techniques shows considerable promise. More research is indicated to determine how to maximize the efficiency of such instruments so that they are more clinically effective.

  16. Artificial Intelligence Assists Ultrasonic Inspection

    Science.gov (United States)

    Schaefer, Lloyd A.; Willenberg, James D.

    1992-01-01

    Subtle indications of flaws extracted from ultrasonic waveforms. Ultrasonic-inspection system uses artificial intelligence to help in identification of hidden flaws in electron-beam-welded castings. System involves application of flaw-classification logic to analysis of ultrasonic waveforms.

  17. Artificial Intelligence Assists Ultrasonic Inspection

    Science.gov (United States)

    Schaefer, Lloyd A.; Willenberg, James D.

    1992-01-01

    Subtle indications of flaws extracted from ultrasonic waveforms. Ultrasonic-inspection system uses artificial intelligence to help in identification of hidden flaws in electron-beam-welded castings. System involves application of flaw-classification logic to analysis of ultrasonic waveforms.

  18. Pure laparoscopic augmentation ileocystoplasty.

    Science.gov (United States)

    Rebouças, Rafael B; Monteiro, Rodrigo C; Souza, Thiago N S de; Aragão, Augusto J de; Burity, Camila R T; Nóbrega, Júlio C de A; Oliveira, Natália S C de; Abrantes, Ramon B; Dantas Júnior, Luiz B; Cartaxo Filho, Ricardo; Negromonte, Gustavo R P; Sampaio, Rafael da C R; Britto, Cesar A

    2014-01-01

    Guillain-Barre syndrome is an acute neuropathy that rarely compromises bladder function. Conservative management including clean intermittent catheterization and pharmacotherapy is the primary approach for hypocompliant contracted bladder. Surgical treatment may be used in refractory cases to improve bladder compliance and capacity in order to protect the upper urinary tract. We describe a case of pure laparoscopic augmentation ileocystoplasty in a patient affected by Guillain-Barre syndrome. A 15-year-old female, complaining of voiding dysfunction, recurrent urinary tract infection and worsening renal function for three months. A previous history of Guillain-Barre syndrome on childhood was related. A voiding cystourethrography showed a pine-cone bladder with moderate post-void residual urine. The urodynamic demonstrated a hypocompliant bladder and small bladder capacity (190 mL) with high detrusor pressure (54 cmH2O). Nonsurgical treatments were attempted, however unsuccessfully.

  19. Pure Parsimony Xor Haplotyping

    CERN Document Server

    Bonizzoni, Paola; Dondi, Riccardo; Pirola, Yuri; Rizzi, Romeo

    2010-01-01

    The haplotype resolution from xor-genotype data has been recently formulated as a new model for genetic studies. The xor-genotype data is a cheaply obtainable type of data distinguishing heterozygous from homozygous sites without identifying the homozygous alleles. In this paper we propose a formulation based on a well-known model used in haplotype inference: pure parsimony. We exhibit exact solutions of the problem by providing polynomial time algorithms for some restricted cases and a fixed-parameter algorithm for the general case. These results are based on some interesting combinatorial properties of a graph representation of the solutions. Furthermore, we show that the problem has a polynomial time k-approximation, where k is the maximum number of xor-genotypes containing a given SNP. Finally, we propose a heuristic and produce an experimental analysis showing that it scales to real-world large instances taken from the HapMap project.

  20. Pure parsimony xor haplotyping.

    Science.gov (United States)

    Bonizzoni, Paola; Della Vedova, Gianluca; Dondi, Riccardo; Pirola, Yuri; Rizzi, Romeo

    2010-01-01

    The haplotype resolution from xor-genotype data has been recently formulated as a new model for genetic studies. The xor-genotype data is a cheaply obtainable type of data distinguishing heterozygous from homozygous sites without identifying the homozygous alleles. In this paper, we propose a formulation based on a well-known model used in haplotype inference: pure parsimony. We exhibit exact solutions of the problem by providing polynomial time algorithms for some restricted cases and a fixed-parameter algorithm for the general case. These results are based on some interesting combinatorial properties of a graph representation of the solutions. Furthermore, we show that the problem has a polynomial time k-approximation, where k is the maximum number of xor-genotypes containing a given single nucleotide polymorphisms (SNP). Finally, we propose a heuristic and produce an experimental analysis showing that it scales to real-world large instances taken from the HapMap project.

  1. Schlieren visualization of ultrasonic standing waves in mm-sized chambers for ultrasonic particle manipulation.

    Science.gov (United States)

    Möller, Dirk; Degen, Nicolas; Dual, Jurg

    2013-06-28

    For the design and characterization of ultrasonic particle manipulation devices the pressure field in the fluid cavity is of great interest. The schlieren method provides an optical tool for the visualization of such pressure fields. Due to its purely optical nature this experimental method has got some unique advantages compared to methods like particle tracking. A vertical schlieren setup and an investigation with the same of a mm-sized chamber used to agglomerate particles are presented here. The schlieren images show a two-dimensional representation of the whole pressure distribution recorded simultaneously with a good resolution in time. The gained description of the pressure field is shown to be in agreement with a numerical simulation. Thermal effects as well as streaming effects are shown. The results show the great potential of schlieren visualization to investigate ultrasonic particle manipulation devices. Visualized are pressure fields, acoustic streaming, temperature effects and effects caused by fluid volumes of different density.

  2. Ultrasonic Stir Welding

    Science.gov (United States)

    Nabors, Sammy

    2015-01-01

    NASA Marshall Space Flight Center (MSFC) developed Ultrasonic Stir Welding (USW) to join large pieces of very high-strength metals such as titanium and Inconel. USW, a solid-state weld process, improves current thermal stir welding processes by adding high-power ultrasonic (HPU) energy at 20 kHz frequency. The addition of ultrasonic energy significantly reduces axial, frictional, and shear forces; increases travel rates; and reduces wear on the stir rod, which results in extended stir rod life. The USW process decouples the heating, stirring, and forging elements found in the friction stir welding process allowing for independent control of each process element and, ultimately, greater process control and repeatability. Because of the independent control of USW process elements, closed-loop temperature control can be integrated into the system so that a constant weld nugget temperature can be maintained during welding.

  3. Ultrasonic colour Doppler imaging

    DEFF Research Database (Denmark)

    Evans, David H; Jensen, Jørgen Arendt; Nielsen, Michael Bachmann

    2011-01-01

    anatomy. The most common use of the technique is to image the movement of blood through the heart, arteries and veins, but it may also be used to image the motion of solid tissues such as the heart walls. Colour Doppler imaging is now provided on almost all commercial ultrasound machines, and has been......Ultrasonic colour Doppler is an imaging technique that combines anatomical information derived using ultrasonic pulse-echo techniques with velocity information derived using ultrasonic Doppler techniques to generate colour-coded maps of tissue velocity superimposed on grey-scale images of tissue...... vectors. This review briefly introduces the principles behind colour Doppler imaging and describes some clinical applications. It then describes the basic components of conventional colour Doppler systems and the methods used to derive velocity information from the ultrasound signal. Next, a number of new...

  4. Geothermal Ultrasonic Fracture Imager

    Energy Technology Data Exchange (ETDEWEB)

    Patterson, Doug [Baker-Hughes Oilfield Operation Inc., Houston, TX (United States); Leggett, Jim [Baker-Hughes Oilfield Operation Inc., Houston, TX (United States)

    2013-07-29

    The Geothermal Ultrasonic Fracture Imager project has a goal to develop a wireline ultrasonic imager that is capable of operating in temperatures up to 300°C (572°F) and depths up to 10 km (32,808 ft). This will address one of the critical needs in any EGS development of understanding the hydraulic flow paths in the reservoir. The ultrasonic imaging is well known in the oil and gas industry as one of the best methods for fracture evaluation; providing both high resolution and complete azimuthal coverage of the borehole. This enables fracture detection and characterization, both natural and induced, providing information as to their location, dip direction and dip magnitude. All of these factors are critical to fully understand the fracture system to enable the optimization of the thermal drainage through injectors and producers in a geothermal resource.

  5. Ultrasonic Processing of Materials

    Science.gov (United States)

    Han, Qingyou

    2015-08-01

    Irradiation of high-energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs and Purdue University on using high-intensity ultrasonic vibrations for degassing molten aluminum, processing particulate-reinforced metal matrix composites, refining metals and alloys during solidification process and welding, and producing bulk nanostructures in solid metals and alloys. Research results suggest that high-intensity ultrasonic vibration is capable of degassing and dispersing small particles in molten alloys, reducing grain size during alloy solidification, and inducing nanostructures in solid metals.

  6. Torsional ultrasonic wave based level measurement system

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, David E. (Oak Ridge, TN); Kisner, Roger A. (Knoxville, TN)

    2012-07-10

    A level measurement system suitable for use in a high temperature and pressure environment to measure the level of coolant fluid within the environment, the system including a volume of coolant fluid located in a coolant region of the high temperature and pressure environment and having a level therein; an ultrasonic waveguide blade that is positioned within the desired coolant region of the high temperature and pressure environment; a magnetostrictive electrical assembly located within the high temperature and pressure environment and configured to operate in the environment and cooperate with the waveguide blade to launch and receive ultrasonic waves; and an external signal processing system located outside of the high temperature and pressure environment and configured for communicating with the electrical assembly located within the high temperature and pressure environment.

  7. Ultrasonic/Sonic Jackhammer

    Science.gov (United States)

    Bar-Cohen, Yoseph; Sherrit, Stewart; Herz, Jack

    2005-01-01

    An ultrasonic/sonic jackhammer (USJ) is the latest in a series of related devices. Each of these devices cuts into a brittle material by means of hammering and chiseling actions of a tool bit excited with a combination of ultrasonic and sonic vibrations. A small-scale prototype of the USJ has been demonstrated. A fully developed, full-scale version of the USJ would be used for cutting through concrete, rocks, hard asphalt, and other materials to which conventional pneumatic jackhammers are applied, but the USJ would offer several advantages over conventional pneumatic jackhammers.

  8. Ultrasonic magnetic abrasive finishing

    Institute of Scientific and Technical Information of China (English)

    LU Ya-ping; MA Ji; ZHANG Jun-qiang; WANG Long-shan

    2006-01-01

    Put forward a new kind of polishing method, ultrasonic magnetic abrasive finishing (UMAF), and studied its mechanism of improving polishing efficiency. By analyzing all kind of forces acting on single abrasive particle in the polishing process and calculating the size of the composition of forces, get the conclusion that UMAF will enhance the efficiency of the normal magnetic abrasive finishing(MAF) due to the ultrasonic vibration increases the cutting force and depth. At last the idea of designing the UMAF system based on numerical control milling machine is put forward which is convenient to setup and will accelerate the practical application of MAF.

  9. Pure Laparoscopic Augmentation Ileocystoplasty

    Directory of Open Access Journals (Sweden)

    Rafael B. Rebouças

    2014-12-01

    Full Text Available Introduction Guillain-Barre syndrome is an acute neuropathy that rarely compromises bladder function. Conservative management including clean intermittent catheterization and pharmacotherapy is the primary approach for hypocompliant contracted bladder. Surgical treatment may be used in refractory cases to improve bladder compliance and capacity in order to protect the upper urinary tract. We describe a case of pure laparoscopic augmentation ileocystoplasty in a patient affected by Guillain-Barre syndrome. Presentation A 15-year-old female, complaining of voiding dysfunction, recurrent urinary tract infection and worsening renal function for three months. A previous history of Guillain-Barre syndrome on childhood was related. A voiding cystourethrography showed a pine-cone bladder with moderate post-void residual urine. The urodynamic demonstrated a hypocompliant bladder and small bladder capacity (190mL with high detrusor pressure (54 cmH2O. Nonsurgical treatments were attempted, however unsuccessfully. The patient was placed in the exaggerated Trendelenburg position. A four-port transperitoneal technique was used. A segment of ileum approximately 15-20cm was selected and divided with its pedicle. The ileal anastomosis and creation of ileal U-shaped plate were performed laparoscopically, without staplers. Bladder mobilization and longidutinal cystotomy were performed. Enterovesical anastomosis was done with continuous running suture. A suprapubic cystostomy was placed through a 5mm trocar. Results The total operative time was 335 min. The blood loss was minimal. The patient developed ileus in the early days, diet acceptance after the fourth day and was discharged on the seventh postoperative day. The urethral catheter was removed after 2 weeks. At 6-month follow-up, a cystogram showed a significant improvement in bladder capacity. The patient adhered well to clean intermittent self-catheterization and there was no report for febrile infections

  10. Improvement of solar ethanol distillation using ultrasonic waves

    Directory of Open Access Journals (Sweden)

    Jaruwat Jareanjit

    2016-08-01

    Full Text Available This report presents a study on the use of ultrasonic waves in solar ethanol distillation to investigate the performance of ultrasonic waves at a frequency of 30 kHz and at 100 Watts that were installed in the inlet area of a 10-litre distillation tank. Based on the non-continuous distillation process (batch distillation, the experiment demonstrated that using ultrasonic waves in solar ethanol distillation caused the average concentration of hourly distilled ethanol to be higher than that of a normal system (solar ethanol distillation without ultrasonic wave at the same or higher distillation rate and hourly distillation volume. The ultrasonic wave was able to enhance the separation of ethanol from the solution (water-ethanol mixture through solar distillation. The amount of pure ethanol product from each distilled batch was clearly larger than the amount of product obtained from a normal system when the initial concentration of ethanol was lower than 50%v/v (% by volume, where an average of approximately 40% and 20% are obtained for an initial ethanol concentration of 10%v/v and 30%v/v, respectively. Furthermore, the distillation rate varied based on the solar radiation value.

  11. Keeping consumers safe: food providers' perspectives on pureed food.

    Science.gov (United States)

    Keller, Heather H; Duizer, Lisa M

    2014-01-01

    Twelve focus groups were conducted in five sites with 80 allied health providers to identify their perspectives on providing pureed food to consumers. Thematic care analysis was completed to summarize and interpret these data. Providers' greatest concern was keeping consumers safe, and the right texture was prioritized over sensory appeal and acceptance. Providers recognized that these foods impacted the quality of life of consumers and worked to rationalize these diets with residents/patients and their families. In addition, offering foods they knew to be poorly accepted affected their self-concept as providers. As a result of these challenges, they did whatever they could in the kitchen and tableside to promote intake of pureed foods. Those in the "food chain" of pureed food provision suggested several ways to further improve these products. Greater communication between those who assist consumers with eating and those who produce the pureed food they consume is needed to promote acceptable pureed products.

  12. Climate Change Communication Research: Trends and Implications ...

    African Journals Online (AJOL)

    Climate Change Communication Research: Trends and Implications. ... journal articles in the areas communication, climate change and agriculture. ... climate change communication to farmers have been purely elitist and quantitative, which ...

  13. Pure and Public, Popular and personal

    DEFF Research Database (Denmark)

    Eriksson, Birgit

    2013-01-01

    In the article I reexamine the traditional aesthetical and political critiques of popular culture and reevaluate the social and communicative potential of bestselling cultural artifacts such as highly popular television series. First, I sketch the alleged aesthetic and social problems of popular...... and the exclusions of the public sphere. I argue that the ideals of a pure aesthetic and a public sphere neglect issues that are crucial to the type of commonality at stake in popular cultural artifacts: personal issues, social conflicts, and what is pleasurable to the senses or has to do with emotions. Third, I...

  14. Aesthetic Communication

    DEFF Research Database (Denmark)

    Thyssen, Ole

    2012-01-01

    Based on Niklas Luhmann's systems theory, aesthetics is defined as a manner of reinforcing the connectivity, or Anschlusswert, of communication. Without changing the content, a message can be made more attractive, strengthening the receiver's willingness to be attentive and accepting. As communic......Based on Niklas Luhmann's systems theory, aesthetics is defined as a manner of reinforcing the connectivity, or Anschlusswert, of communication. Without changing the content, a message can be made more attractive, strengthening the receiver's willingness to be attentive and accepting....... As communication inevitably makes use of a sensuous medium, such as light or sound, all communication has an aesthetic dimension. In the 19th Century, an important distinction was made between pure and applied art, following Immanuel Kant's separation of theory of knowledge, moral theory and aesthetic theory....... Whereas pure art is produced in order to be observed, applied art has to fulfill practical purposes as well. Modern organizations, defined as systems of communication, may use art works to embellish and define themselves. But they inevitably use applied art as a practical tool in their normal...

  15. Visual processing in pure alexia

    DEFF Research Database (Denmark)

    Starrfelt, Randi; Habekost, Thomas; Gerlach, Christian

    2010-01-01

    Whether pure alexia is a selective disorder that affects reading only, or if it reflects a more general visual disturbance, is highly debated. We have investigated the selectivity of visual deficits in a pure alexic patient (NN) using a combination of psychophysical measures, mathematical modelling...

  16. Introduction to ultrasonic motors

    Energy Technology Data Exchange (ETDEWEB)

    Sashida, Toshiiku; Kenjo, Takashi.

    1993-01-01

    The ultrasonic motor, invented in 1980, utilizes the piezoelectric effect in the ultrasonic frequency range to provide the motive force. (In conventional electric motors the motive force is electromagnetic.) The result is a motor with unusually good low-speed high-torque and power-to-weight characteristics. It has already found applications in camera autofocus mechanisms, medical equipment subject to high magnetic fields, and motorized car accessories. Its applications will increase as designers become more familiar with its unique characteristics. This book is the result of a collaboration between the inventor and an expert in conventional electric motors: the result is an introduction to the general theory presented in a way that links it to conventional motor theory. It will be invaluable both to motor designers and to those who design with and use electric motors as an introduction to this important new invention.

  17. An Ultrasonic Levitator

    Directory of Open Access Journals (Sweden)

    R.R. Boullosa

    2013-12-01

    Full Text Available We report the development of an ultrasonic levitation system. Liquid drops or solid samples of diameter less than one half wavelength of the excitation frequency are levitated without contact just below the pressure nodes. The piezo transducer is excited by an ultrasonic signal of around 29 kHz through a voltage amplifier. The choice of the number of half-waves of the acoustic field in the space between the reflector and radiator is made by means of a micrometer. A lamp, an amplifier and a frequency generator are integrated to the levitator. The diameters of the droplets of liquid that can levitate are of the order of tenths of mm to 3 or 4 mm, depending on the liquid properties (density, surface tension, etc.. Solid objects can also be levitated. The maximum voltage of the system is 20 Vrms.

  18. Pulsed ultrasonic stir welding system

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2013-01-01

    An ultrasonic stir welding system includes a welding head assembly having a plate and a rod passing through the plate. The rod is rotatable about a longitudinal axis thereof. During a welding operation, ultrasonic pulses are applied to the rod as it rotates about its longitudinal axis. The ultrasonic pulses are applied in such a way that they propagate parallel to the longitudinal axis of the rod.

  19. Ultrasonic techniques for process monitoring and control.

    Energy Technology Data Exchange (ETDEWEB)

    Chien, H.-T.

    1999-03-24

    Ultrasonic techniques have been applied successfully to process monitoring and control for many industries, such as energy, medical, textile, oil, and material. It helps those industries in quality control, energy efficiency improving, waste reducing, and cost saving. This paper presents four ultrasonic systems, ultrasonic viscometer, on-loom, real-time ultrasonic imaging system, ultrasonic leak detection system, and ultrasonic solid concentration monitoring system, developed at Argonne National Laboratory in the past five years for various applications.

  20. Ultrasonic investigations in intermetallics

    Indian Academy of Sciences (India)

    Devraj Singh; D K Pandey

    2009-02-01

    Ultrasonic attenuation for the longitudinal and shear waves due to phonon–phonon interaction and thermoelastic mechanism have been evaluated in B2 structured in-termetallic compounds AgMg, CuZr, AuMg, AuTi, AuMn, AuZn and AuCd along $\\langle 1 0 0 \\rangle, \\langle 1 1 1 \\rangle and \\langle 1 1 0 \\rangle crystallographic directions at room temperature. For the same evaluations, second- and third-order elastic constants, ultrasonic velocities, Grüneisen parameters, non-linearity parameter, Debye temperature and thermal relaxation time are also computed. Although the molecular weight of these materials increases from AgMg to AuCd, the obtained results are affected with the deviation number. Attenuation of ultrasonic waves due to phonon–phonon interaction is predominant over thermoelastic loss. Results are compared with available theoretical and experimental results. The results with other well-known physical properties are useful for industrial purposes.

  1. Ultrasonic Cutting of Foods

    Science.gov (United States)

    Schneider, Yvonne; Zahn, Susann; Rohm, Harald

    In the field of food engineering, cutting is usually classified as a mechanical unit operation dealing with size reduction by applying external forces on a bulk product. Ultrasonic cutting is realized by superpositioning the macroscopic feed motion of the cutting device or of the product with a microscopic vibration of the cutting tool. The excited tool interacts with the product and generates a number of effects. Primary energy concentration in the separation zone and the modification of contact friction along the tool flanks arise from the cyclic loading and are responsible for benefits such as reduced cutting force, smooth cut surface, and reduced product deformation. Secondary effects such as absorption and cavitation originate from the propagation of the sound field in the product and are closely related to chemical and physical properties of the material to be cut. This chapter analyzes interactions between food products and ultrasonic cutting tools and relates these interactions with physical and chemical product properties as well as with processing parameters like cutting velocity, ultrasonic amplitude and frequency, and tool design.

  2. Ultrasonic processing of aluminum alloys

    NARCIS (Netherlands)

    Zhang, L.

    2013-01-01

    The research in ultrasonic processing for metallurgical application shows a promising influence on improving casting properties of aluminium alloys. The principle of ultrasonic processing is introduction of acoustic waves with a frequency higher than 17 kHz into liquid metal. Several promising

  3. Ultrasonic dyeing of cellulose nanofibers.

    Science.gov (United States)

    Khatri, Muzamil; Ahmed, Farooq; Jatoi, Abdul Wahab; Mahar, Rasool Bux; Khatri, Zeeshan; Kim, Ick Soo

    2016-07-01

    Textile dyeing assisted by ultrasonic energy has attained a greater interest in recent years. We report ultrasonic dyeing of nanofibers for the very first time. We chose cellulose nanofibers and dyed with two reactive dyes, CI reactive black 5 and CI reactive red 195. The cellulose nanofibers were prepared by electrospinning of cellulose acetate (CA) followed by deacetylation. The FTIR results confirmed complete conversion of CA into cellulose nanofibers. Dyeing parameters optimized were dyeing temperature, dyeing time and dye concentrations for each class of the dye used. Results revealed that the ultrasonic dyeing produced higher color yield (K/S values) than the conventional dyeing. The color fastness test results depicted good dye fixation. SEM analysis evidenced that ultrasonic energy during dyeing do not affect surface morphology of nanofibers. The results conclude successful dyeing of cellulose nanofibers using ultrasonic energy with better color yield and color fastness results than conventional dyeing.

  4. Ultrasonic actuators for nanometre positioning

    Science.gov (United States)

    Snitka

    2000-03-01

    This paper deals with ultrasonic motors based on bimodal plate vibrations and their application to nanometre resolution stepper positioning systems. The concept of a linear ultrasonic motor drive capable of nanometric steps, long-range travel and reversible controlled motion is presented. The motor concept developed is based on the superposition of a longitudinal and bending vibrations of a rectangular resonator. The ultrasonic motor model based on system identification via discrete observations and prediction has been developed for control applications. The control algorithm for ultrasonic motors has been developed and theoretical investigations have been made. The open loop positioning system with designed stepper ultrasonic drive produced 10 nm resolution and 5% displacement repeatability. The system with computer controlled position feedback has shown 0.3 micron positioning accuracy over the 100 mm positioning range.

  5. Ultrasonic cleaning in the hospital.

    Science.gov (United States)

    Detwiler, M S

    1989-04-01

    Ultrasonic cleaning can prolong the life of expensive instruments. In the past, many fine instruments were discarded due to stiffening hinges and box locks, or sticking plungers. Hand scrubbing and spray washing could not thoroughly clean these areas. Ultrasonic cleaners effectively remove dried and baked blood, serums and medications from these instruments. Also, hinged instruments and syringes operate more smoothly during use in surgery when cleaned using ultrasonics. In addition, the use of ultrasonics alleviates the necessity for hand scrubbing of contaminated surgical instruments and laboratory apparatus, a procedure which could lead to injury or infection. The superb cleaning powers of ultrasonic cleaners, their speed and simplicity of operation, and their ability to remove blood, tissue, bacteria and microorganisms within minutes, makes them a valuable addition to any operating room suite, central service department, or emergency room. Their cost-effectiveness is considerable for the small hospital, and compelling for the large hospital.

  6. pupyMPI - MPI implemented in pure Python

    DEFF Research Database (Denmark)

    Bromer, Rune; Hantho, Frederik; Vinter, Brian

    2011-01-01

    As distributed memory systems have become common, the de facto standard for communication is still the Message Passing Interface (MPI). pupyMPI is a pure Python implementation of a broad subset of the MPI 1.3 specifications that allows Python programmers to utilize multiple CPUs with datatypes...

  7. Ultrasonic Force Microscopies

    Science.gov (United States)

    Kolosov, Oleg; Briggs, Andrew

    Ultrasonic Force Microscopy, or UFM, allows combination of two apparently mutually exclusive requirements for the nanomechanical probe—high stiffness for the efficient indentation and high mechanical compliance that brings force sensitivity. Somewhat inventively, UFM allows to combine these two virtues in the same cantilever by using indention of the sample at high frequency, when cantilever is very rigid, but detecting the result of this indention at much lower frequency. That is made possible due to the extreme nonlinearity of the nanoscale tip-surface junction force-distance dependence, that acts as "mechanical diode" detecting ultrasound in AFM. After introducing UFM principles, we discuss features of experimental UFM implementation, and the theory of contrast in this mode, progressing to quantitative measurements of contact stiffness. A variety of UFM applications ranging from semiconductor quantum nanostructures, graphene, very large scale integrated circuits, and reinforced ceramics to polymer composites and biological materials is presented via comprehensive imaging gallery accompanied by the guidance for the optimal UFM measurements of these materials. We also address effects of adhesion and topography on the elasticity imaging and the approaches for reducing artifacts connected with these effects. This is complemented by another extremely useful feature of UFM—ultrasound induced superlubricity that allows damage free imaging of materials ranging from stiff solid state devices and graphene to biological materials. Finally, we proceed to the exploration of time-resolved nanoscale phenomena using nonlinear mixing of multiple vibration frequencies in ultrasonic AFM—Heterodyne Force Microscopy, or HFM, that also include mixing of ultrasonic vibration with other periodic physical excitations, eg. electrical, photothermal, etc. Significant section of the chapter analyzes the ability of UFM and HFM to detect subsurface mechanical inhomogeneities, as well as

  8. Mastectomy using ultrasonic dissection

    DEFF Research Database (Denmark)

    Galatius, Hanne; Okholm, Mette; Hoffmann, Jack

    2003-01-01

    Seroma formation is the most common complication after mastectomy. Among the several known etiological factors the surgical procedure used may be of importance for seroma formation. This prospective study was carried out to evaluate the ultrasonic energy dissection technique and its effect...... on seroma formation and other complications: 59 patients with operable breast cancer underwent modified radical mastectomy, performed in 30 of them with an Ultracision Harmonic scalpel and in 29 with scissors and electrocautery. In all cases a standard level II axillary dissection was performed...... groups. In conclusion, neither clinical advantages or disadvantages of the ultrasound dissection technique were found....

  9. Experimental study on titanium wire drawing with ultrasonic vibration.

    Science.gov (United States)

    Liu, Shen; Shan, Xiaobiao; Guo, Kai; Yang, Yuancai; Xie, Tao

    2017-08-12

    Titanium and its alloys have been widely used in aerospace and biomedical industries, however, they are classified as difficult-to-machine materials. In this paper, ultrasonic vibration is imposed on the die to overcome the difficulties during conventional titanium wire drawing processes at the room temperature. Numerical simulations were performed to investigate the variation of axial stress within the contacting region and study the change of the drawing stress with several factors in terms of the longitudinal amplitude and frequency of the applied ultrasonic vibration, the diameter reduction ratio, and the drawing force. An experimental testing equipment was established to measure the drawing torque and rotational velocity of the coiler drum during the wire drawing process. The result indicates the drawing force increases with the growth of the drawing velocity and the reduction ratio, whether with or without vibrations. Application of either form of ultrasonic vibrations contributes to the further decrease of the drawing force, especially the longitudinal vibration with larger amplitude. SEM was employed to detect the surface morphology of the processed wires drawn under the three circumstances. The surface quality of the drawn wires with ultrasonic vibrations was apparently improved compared with those using conventional method. In addition, the longitudinal and torsional composite vibration was more effective for surface quality improvement than pure longitudinal vibration, however, at the cost of weakened drawing force reduction effect. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Ultrasonic Measurements of Temperature in Aqueous Solutions: Why and How

    Directory of Open Access Journals (Sweden)

    A. Afaneh

    2011-01-01

    Full Text Available The paper describes two different approaches to ultrasonic measurements of temperature in aqueous solutions. The first approach uses two narrowband ultrasonic transducers and support electronics that form an oscillating sensor which output frequency is related to the measured temperature. This low-cost sensor demonstrated sensitivity of about 40 Hz/K at the distance of 190 mm and the operating frequency of about 25 kHz. The second approach utilised pulse-echo mode at the centre frequency of 20 MHz. The reflector featured a cavity that was filled with deionised water. The ultrasound propagation delay in the cavity was related to the temperature in the solution. The experiments were conducted for deionised water, and solutions of sodium persulfate, sodium chloride, and acetic acid with concentrations up to 0.5 M. In the experiments (conducted within the temperature range from 15 to 30°C, we observed increases in the ultrasound velocity for increased temperatures and concentrations as was expected. Measurement results were compared with literature data for pure and seawater. It was concluded that ultrasonic measurements of temperature were conducted with the resolution well below 0.1 K for both methods. Advantages of ultrasonic temperature measurements over conventional thermometers were discussed.

  11. Ultrasonic Evaluation and Imaging

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, Susan L.; Anderson, Michael T.; Diaz, Aaron A.; Larche, Michael R.; Prowant, Matthew S.; Cinson, Anthony D.

    2015-10-01

    Ultrasonic evaluation of materials for material characterization and flaw detection is as simple as manually moving a single-element probe across a speci-men and looking at an oscilloscope display in real time or as complex as automatically (under computer control) scanning a phased-array probe across a specimen and collecting encoded data for immediate or off-line data analyses. The reliability of the results in the second technique is greatly increased because of a higher density of measurements per scanned area and measurements that can be more precisely related to the specimen geometry. This chapter will briefly discuss applications of the collection of spatially encoded data and focus primarily on the off-line analyses in the form of data imaging. Pacific Northwest National Laboratory (PNNL) has been involved with as-sessing and advancing the reliability of inservice inspections of nuclear power plant components for over 35 years. Modern ultrasonic imaging techniques such as the synthetic aperture focusing technique (SAFT), phased-array (PA) technolo-gy and sound field mapping have undergone considerable improvements to effec-tively assess and better understand material constraints.

  12. Ultrasonic Transducer Irradiation Test Results

    Energy Technology Data Exchange (ETDEWEB)

    Daw, Joshua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Palmer, Joe [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ramuhalli, Pradeep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Keller, Paul [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Montgomery, Robert [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chien, Hual-Te [Argonne National Lab. (ANL), Argonne, IL (United States); Kohse, Gordon [MIT (Massachusetts Inst. of Technology), Cambridge, MA (United States); Tittmann, Bernhard [Pennsylvania State Univ., University Park, PA (United States); Reinhardt, Brian [Pennsylvania State Univ., University Park, PA (United States); Rempe, Joy [Rempe and Associates, Idaho Falls, ID (United States)

    2015-02-01

    Ultrasonic technologies offer the potential for high-accuracy and -resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other ongoing efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. For this reason, the Pennsylvania State University (PSU) was awarded an ATR NSUF project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2. The goal of this research is to characterize and demonstrate magnetostrictive and piezoelectric transducer operation during irradiation, enabling the development of novel radiation-tolerant ultrasonic sensors for use in Material Testing Reactors (MTRs). As such, this test is an instrumented lead test and real-time transducer performance data is collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers. To date, one piezoelectric

  13. Irradiation Testing of Ultrasonic Transducers

    Energy Technology Data Exchange (ETDEWEB)

    Daw, Joshua; Tittmann, Bernhard; Reinhardt, Brian; Kohse, Gordon E.; Ramuhalli, Pradeep; Montgomery, Robert O.; Chien, Hual-Te; Villard, Jean-Francois; Palmer, Joe; Rempe, Joy

    2014-07-30

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of single, small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of existing knowledge of ultrasonic transducer material survivability under irradiation conditions. For this reason, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate promising magnetostrictive and piezoelectric transducer performance in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2 (E> 0.1 MeV). The goal of this research is to characterize magnetostrictive and piezoelectric transducer survivability during irradiation, enabling the development of novel radiation tolerant ultrasonic sensors for use in Material and Test Reactors (MTRs). As such, this test will be an instrumented lead test and real-time transducer performance data will be collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers.

  14. Ultrasonic splitting of oil-in-water emulsions

    DEFF Research Database (Denmark)

    Hald, Jens; König, Ralf; Benes, Ewald

    1999-01-01

    Standing resonant ultrasonic wave fields can be utilized for liquid–liquid separation of the dispersed particles and the fluid caused by the acoustic radiation pressure and the induced particle agglomeration or coagulation/coalescence process. For the splitting of oil-in-water emulsions...... emulsion samples have been investigated. The quality of the ultrasonic-induced particle separation/coagulation process is characterized by physical–chemical analysis of the separated oil- and water phase and by determining the change of the particle size distribution of the initial emulsion due...... of up to 24 W/cm2 into the sonication volume. The chosen resonance frequency is kept stable by automatic frequency control utilizing the maximum true power criterion. Physically and chemically well-defined low and high density pure laboratory and also industrially used cooling-lubricating oil-in-water...

  15. Relativity of pure states entanglement

    CERN Document Server

    Zyczkowski, K; Zyczkowski, Karol; Bengtsson, Ingemar

    2002-01-01

    Entanglement of any pure state of an N times N bi-partite quantum system may be characterized by the vector of coefficients arising by its Schmidt decomposition. We analyze various measures of entanglement derived from the generalized entropies of the vector of Schmidt coefficients. For N >= 3 they generate different ordering in the set of pure states and for some states their ordering depends on the measure of entanglement used. This odd-looking property is acceptable, since these incomparable states cannot be transformed to each other with unit efficiency by any local operation. In analogy to special relativity the set of pure states equivalent under local unitaries has a causal structure so that at each point the set splits into three parts: the 'Future', the 'Past' and the set of noncomparable states.

  16. Fundamentals of ultrasonic phased arrays

    CERN Document Server

    Schmerr, Lester W

    2014-01-01

    This book describes in detail the physical and mathematical foundations of ultrasonic phased array measurements.?The book uses linear systems theory to develop a comprehensive model of the signals and images that can be formed with phased arrays. Engineers working in the field of ultrasonic nondestructive evaluation (NDE) will find in this approach a wealth of information on how to design, optimize and interpret ultrasonic inspections with phased arrays. The fundamentals and models described in the book will also be of significant interest to other fields, including the medical ultrasound and

  17. Pulsed ultrasonic stir welding method

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2013-01-01

    A method of performing ultrasonic stir welding uses a welding head assembly to include a plate and a rod passing through the plate. The rod is rotatable about a longitudinal axis thereof. In the method, the rod is rotated about its longitudinal axis during a welding operation. During the welding operation, a series of on-off ultrasonic pulses are applied to the rod such that they propagate parallel to the rod's longitudinal axis. At least a pulse rate associated with the on-off ultrasonic pulses is controlled.

  18. Ultrasonic Assembly of Thermoplastic Parts

    Energy Technology Data Exchange (ETDEWEB)

    Schurman, W. R.

    1970-03-31

    Four ultrasonic methods were evaluated for assembly of experimental plastic parts for detonators: (1) welding, (2) crimping and staking, (3) insertion, and (4) reactivation of adhesives. For welding, staking and insertion, plastics with low elastic moduli, such as acrylics and polycarbonate, produced the best results. Thermosetting, hot-melt, and solution adhesives could all be activated ultrasonically to form good bonds on plastics and other materials. This evaluation indicated that thermoplastic detonator parts could be assembled ultrasonically in shorter times than by present production techniques with high bond strengths and high product acceptance rates.

  19. "Pure" cutaneous histiocytosis-X.

    Science.gov (United States)

    Wolfson, S L; Botero, F; Hurwitz, S; Pearson, H A

    1981-11-15

    The case histories of two young children who experienced skin rashes involving various areas of the body are reported. The diagnosis of pure cutaneous histiocytosis-X was established after extensive studies revealed no other organ involvement. The patients were treated with oral corticosteroids. Currently, both children are in good health, show no evidence of disease, and have been followed over a four-to-five-year period. Therapy with corticosteroids may not be indicated with pure cutaneous histiocytosis-X unless there is evidence of extracutaneous dissemination or rapid progression of the disease.

  20. Pure Spinors for General Backgrounds

    CERN Document Server

    Fre', Pietro

    2008-01-01

    We show the equivalence of the different types of pure spinor constraints geometrically derived from the Free Differential Algebras of N=2 d=10 supergravities. Firstly, we compute the general solutions of these constraints, using both a G_2 and an SO(8) covariant decomposition of the 10d chiral spinors. Secondly, we verify that the number of independent degrees of freedom is equal to that implied by the Poincare' pure spinor constraints so-far used for superstrings, namely twenty two. Thirdly, we show the equivalence between the FDA type IIA/B constraints among each other and with the Poincare' ones.

  1. A practical ultrasonic plethysmograph

    Science.gov (United States)

    Wu, V. C.; Nickell, W. T.; Bhagat, P. K.

    1982-01-01

    An ultrasonic plethysmograph, which gives improved performance over the standard Whitney Strain Gauge, is described. This instrument monitors dimension changes in human limbs by measuring the transit times of acoustic pulses across two chords of the limb. In the case of a small uniform expansion, the percentage change in limb volume is shown to be proportional to twice the percentage change in either of the measured chords. Measurement of two chords allows correction for possible non-uniform expansion. In addition, measurement of two chords allows an estimate of the absolute cross-sectional area of the limb. The developed instrument incorporates a microprocessor, which performs necessary calculation and control functions. Use of the microprocessor allows the instrument to be self-calibrating. In addition, the device can be easily reprogrammed to incorporate improvements in operating features or computational schemes.

  2. Repeat scanning technology for laser ultrasonic propagation imaging

    Science.gov (United States)

    Lee, Jung-Ryul; Yenn Chong, See; Sunuwar, Nitam; Park, Chan Yik

    2013-08-01

    Laser ultrasonic scanning in combination with contact or non-contact sensors provides new paradigms in structural health management (SHM) and non-destructive in-process quality control (IPQC) for large composite structures. Wave propagation imaging technology based on laser ultrasonic scanning and fixed-point sensing shows remarkable advantages, such as minimal need for embedded sensors in SHM, minimum invasive defect visualization in IPQC and general capabilities of curved and complex target inspection, and temporal reference-free inspection. However, as with other SHM methods and non-destructive evaluation based on ultrasound, the signal-to-noise ratio (SNR) is a prevalent issue in real structural applications, especially with non-contact thin-composite sensing or with thick and heterogeneous composites. This study proposes a high-speed repeat scanning technique for laser ultrasonic propagation imaging (UPI) technology, which is realized with the scanning speed of 1 kHz of a Q-switched continuous wave laser, and precise control of the laser beam pulses for identical point scanning. As a result, the technique enables the achievement of significant improvement in the SNR to inspect real-world composite structures. The proposed technique provides enhanced results for impact damage detection in a 2 mm thick wing box made of carbon-fiber-reinforced plastic, despite the low sensitivity of non-contact laser ultrasonic sensing. A field-applicable pure laser UPI system has been developed using a laser Doppler vibrometer as the non-contact ultrasonic sensor. The proposed technique enables the visualization of the disbond defect in a 15 mm thick wind blade specimen made of glass-fiber-reinforced plastic, despite the high dissipation of ultrasound in the thick composite.

  3. Pure robotic retrocaval ureter repair

    Directory of Open Access Journals (Sweden)

    Ashok k. Hemal

    2008-12-01

    Full Text Available PURPOSE: To demonstrate the feasibility of pure robotic retrocaval ureter repair. MATERIALS AND METHODS: A 33 year old female presented with right loin pain and obstruction on intravenous urography with the classical "fish-hook" appearance. She was counseled on the various methods of repair and elected to have a robot assisted repair. The following steps are performed during a pure robotic retrocaval ureter repair. The patient is placed in a modified flank position, pneumoperitoneum created and ports inserted. The colon is mobilized to expose the retroperitoneal structures: inferior vena cava, right gonadal vein, right ureter, and duodenum. The renal pelvis and ureter are mobilized and the renal pelvis transected. The ureter is transposed anterior to the inferior vena cava and a pyelopyelostomy is performed over a JJ stent. RESULTS: This patient was discharged on postoperative day 3. The catheter and drain tube were removed on day 1. Her JJ stent was removed at 6 weeks postoperatively. The postoperative intravenous urography at 3 months confirmed normal drainage of contrast medium. CONCLUSION: Pure robotic retrocaval ureter is a feasible procedure; however, there does not appear to be any great advantage over pure laparoscopy, apart from the ergonomic ease for the surgeon as well the simpler intracorporeal suturing.

  4. Ultrasonic Atomization Amount for Different Frequencies

    Science.gov (United States)

    Yasuda, Keiji; Honma, Hiroyuki; Xu, Zheng; Asakura, Yoshiyuki; Koda, Shinobu

    2011-07-01

    The mass flow rate of ultrasonic atomization was estimated by measuring the vaporization amount from a bulk liquid with a fountain. The effects of ultrasonic frequency and intensity on the atomization characteristics were investigated when the directivities of the acoustic field from a transducer were almost the same. The sample was distillated water and the ultrasonic frequencies were 0.5, 1.0, and 2.4 MHz. The mass flow rate of ultrasonic atomization increased with increasing ultrasonic intensity and decreasing ultrasonic frequency. The fountain was formed at the liquid surface where the effective value of acoustic pressure was above atmospheric pressure. The fountain height was strongly governed by the acoustic pressure at the liquid surface of the transducer center. At the same ultrasonic intensity, the dependence of ultrasonic frequency on the number of atomized droplets was small. At the same apparent surface area of the fountain, the number of atomized droplets became larger as the ultrasonic frequency increased.

  5. 多通道超声探伤系统中的高速通信接口技术%The High-Speed Communications Interface Technology in Multi-Channel Ultrasonic Inspection System

    Institute of Scientific and Technical Information of China (English)

    桂婧; 李建东

    2011-01-01

    In this paper, using high-speed and high-performance programmable logic device FPGA, with Nios Ⅱ embedded processor, loading μC/OS-Ⅱ real-time operating system, based on NicheStack TCP/IP protocol stack, using Socket API programming, the design of embedded Gigabit Ethernet in a multi-channel ultrasonic inspection system used in testing Hollow shaft of motor car is described in detail. Testing with Wireshark Network Analyzer installed in the host computer, and the results show that data transmission, receiving and sending data are in exactly the same data, no errors and omissions, the transmission speed is stable with continuous 24-hour transmission test.%本文采用高速、高性能可编程逻辑器件FPGA,利用内部NiosⅡ嵌入式处理器,加载μC/OSⅡ实时操作系统,基于NicheStack TCP/IP协议栈,采用Socket API编程,阐述了在动车空心轴无损检测的多通道超声探伤系统中实现嵌入式干兆以太网的过程。实验结果表明:传输数据准确、传输速度稳定。

  6. High resolution ultrasonic spectroscopy system for nondestructive evaluation

    Science.gov (United States)

    Chen, C. H.

    1991-01-01

    With increased demand for high resolution ultrasonic evaluation, computer based systems or work stations become essential. The ultrasonic spectroscopy method of nondestructive evaluation (NDE) was used to develop a high resolution ultrasonic inspection system supported by modern signal processing, pattern recognition, and neural network technologies. The basic system which was completed consists of a 386/20 MHz PC (IBM AT compatible), a pulser/receiver, a digital oscilloscope with serial and parallel communications to the computer, an immersion tank with motor control of X-Y axis movement, and the supporting software package, IUNDE, for interactive ultrasonic evaluation. Although the hardware components are commercially available, the software development is entirely original. By integrating signal processing, pattern recognition, maximum entropy spectral analysis, and artificial neural network functions into the system, many NDE tasks can be performed. The high resolution graphics capability provides visualization of complex NDE problems. The phase 3 efforts involve intensive marketing of the software package and collaborative work with industrial sectors.

  7. ULTRASONIC BEHAVIOR OF EPOXY RESINS/POLY (ETHYLENE OXIDE)BLENDS CURED WITH PHTHALIC ANHYDRIDE

    Institute of Scientific and Technical Information of China (English)

    ZHENG Sixun; WANG Haiqian; LUO Xiaolie; ZHANG Naibin; MA Dezhu; ZHU Changfei; HU Jiankai

    1995-01-01

    By means of ultrasonic attenuation apparatus, the ultrasonic velocity and attenuation of anhydride-cured epoxy resins (EP)/poly(ethylene oxide)(PEO)blends were measured on the basis of pulse-echo method. It was found that the sonic velocity of the blends decreased as the temperature increased, but attenuation coefficient increased and possessed a peak value. Larger velocity and smaller attenuation coefficient(α)can be obtained from perfect crosslinking network structures of pure DGEBA cured with phthalic anhydride (PA). As for cured DGEBA/PEO blend systems,sonic velocity decreased as a function of PEO concentration,but attenuation coefficient (α) increased.

  8. Shifting from preconceptions to pure wonderment.

    Science.gov (United States)

    Porr, Caroline

    2005-07-01

    The author reflects upon her role as a public health nurse striving to attain practice authenticity. Client assessment and nursing interventions were seemingly sufficient until she became curious about 'Who is this person sitting across from me?' and 'What are her experiences in the world as a lone parent living in poverty at the margins of society?' The author begins to think that she could shift from mere client investigation to pure wonderment about the Other by imagining herself as a researcher, an explorer of another's life world. Ultimately this process enables her to enhance the 'caring' in her practice with the knowledge gained of the perceptions and meanings impoverished clients assigned to their everyday lives. Jurgen Habermas' theory of communicative competence serves as the reference map guiding exploration. The author uses Habermas' theoretical principles of intersubjective mutuality--the validity claims of comprehensibility, truth, sincerity, and legitimacy. Comprehensibility embodies understanding, an attitude of unconditional acceptance, and care respect of another's individual person and self-defined reality. Intersubjective mutuality also requires that one dwell in the moment with the Other, satisfied that communication is founded on truth. Sincerity implies fostering the Other's expression of authentic self apart from oppressive distracters. Lastly, legitimacy reconciles the author's altruistic pursuit to know the Other's ontological truth with the reality of the present world.

  9. Manifolds of interconvertible pure states

    OpenAIRE

    Sinolecka, Magdalena M.; Zyczkowski, Karol; Kus, Marek

    2001-01-01

    Local orbits of a pure state of an N x N bi-partite quantum system are analyzed. We compute their dimensions which depends on the degeneracy of the vector of coefficients arising by the Schmidt decomposition. In particular, the generic orbit has 2N^2 -N-1 dimensions, the set of separable states is 4(N-1) dimensional, while the manifold of maximally entangled states has N^2-1 dimensions.

  10. Manifolds of interconvertible pure states

    CERN Document Server

    Sinolecka, M M; Kus, M; Sinolecka, Magdalena M.; Zyczkowski, Karol; Kus, Marek

    2002-01-01

    Local orbits of a pure state of an N x N bi-partite quantum system are analyzed. We compute their dimensions which depends on the degeneracy of the vector of coefficients arising by the Schmidt decomposition. In particular, the generic orbit has 2N^2 -N-1 dimensions, the set of separable states is 4(N-1) dimensional, while the manifold of maximally entangled states has N^2-1 dimensions.

  11. Multimedia programming with pure data

    CERN Document Server

    Chung, Bryan

    2013-01-01

    A quick and comprehensive tutorial book for media designers to jump-start interactive multimedia production with computer graphics, digital audio, digital video, and interactivity, using the Pure Data graphical programming environment.An introductory book on multimedia programming for media artists/designers who like to work on interactivity in their projects, digital art/design students who like to learn the first multimedia programming technique, and audio-visual performers who like to customize their performance sets

  12. Ultrasonic measurements and technologies

    CERN Document Server

    Kočiš, Štefan

    1996-01-01

    An impulse for writing this book has originated from the effort to sum­ marize and publicise the acquired results of a research team at the De­ partment of Automation of the Faculty of Electrical Engineering and In­ formatics, Slovak Technical University in Bratislava. The research team has been involved for a long time with control problems for machine production mechanisms and, in recent (approximately 15) years, its effort was aimed mostly at the control of electrical servosystems of robots. Within this scope, the members of the authors' staff solved the State Re­ search Task Ultrasonic sensing of the position of a robot hand, which was coordinated by the Institute of Technical Cybernetics of the Slovak Academy of Sciences in Bratislava. The problem was solved in a complex way, i.e. from a conceptual de­ sign of the measurement, through the measurement and evaluation sys­ tem, up to connection to the control system of a robot. Compensation of the atmospheric influence on the precision of measurement,...

  13. 21 CFR 872.4850 - Ultrasonic scaler.

    Science.gov (United States)

    2010-04-01

    ... DEVICES DENTAL DEVICES Surgical Devices § 872.4850 Ultrasonic scaler. (a) Identification. An ultrasonic scaler is a device intended for use during dental cleaning and periodontal (gum) therapy to...

  14. Ultrasonic stir welding process and apparatus

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2009-01-01

    An ultrasonic stir welding device provides a method and apparatus for elevating the temperature of a work piece utilizing at least one ultrasonic heater. Instead of relying on a rotating shoulder to provide heat to a workpiece an ultrasonic heater is utilized to provide ultrasonic energy to the workpiece. A rotating pin driven by a motor assembly performs the weld on the workpiece. A handheld version can be constructed as well as a fixedly mounted embodiment.

  15. Application and development of ultrasonics in dentistry.

    Science.gov (United States)

    Chen, Yen-Liang; Chang, Hao-Hueng; Chiang, Yu-Chih; Lin, Chun-Pin

    2013-11-01

    Since the 1950s, dentistry's ultrasonic instruments have developed rapidly. Because of better visualization, operative convenience, and precise cutting ability, ultrasonic instruments are widely and efficiently applied in the dental field. This article describes the development and improvement of ultrasonic instruments in several dental fields. Although some issues still need clarification, the results of previous studies indicate that ultrasonic instruments have a high potential to become convenient and efficient dental tools and deserve further development.

  16. Very high cycle fatigue testing of concrete using ultrasonic cycling

    Energy Technology Data Exchange (ETDEWEB)

    Karr, Ulrike; Schuller, Reinhard; Fitzka, Michael; Mayer, Herwig [Univ. of Natural Resources and Life Sciences, Vienna (Austria). Inst. of Physics and Materials Science; Denk, Andreas; Strauss, Alfred [Univ. of Natural Resources and Life Sciences, Vienna (Austria)

    2017-06-01

    The ultrasonic fatigue testing method has been further developed to perform cyclic compression tests with concrete. Cylindrical specimens vibrate in resonance at a frequency of approximately 20 kHz with superimposed compressive static loads. The high testing frequency allows time-saving investigations in the very high cycle fatigue regime. Fatigue tests were carried out on ''Concrete 1'' (compressive strength f{sub c} = 80 MPa) and ''Concrete 2'' (f{sub c} = 107 MPa) under purely compressive loading conditions. Experiments at maximum compressive stresses of 0.44 f{sub c} (Concrete 1) and 0.38 f{sub c} (Concrete 2) delivered specimen failures above 109 cycles, indicating that no fatigue limit exists for concrete below one billion load cycles. Resonance frequency, power required to resonate the specimen and second order harmonics of the vibration are used to monitor fatigue damage in situ. Specimens were scanned by X-ray computed tomography prior to and after testing. Fatigue cracks were produced by ultrasonic cycling in the very high cycle fatigue regime at interfaces of grains as well as in cement. The possibilities as well as limitations of ultrasonic fatigue testing of concrete are discussed.

  17. Selective generation of ultrasonic Lamb waves by electromagnetic acoustic transducers

    Science.gov (United States)

    Li, Ming-Liang; Deng, Ming-Xi; Gao, Guang-Jian

    2016-12-01

    In this paper, we describe a modal expansion approach for the analysis of the selective generation of ultrasonic Lamb waves by electromagnetic acoustic transducers (EMATs). With the modal expansion approach for waveguide excitation, an analytical expression of the Lamb wave’s mode expansion coefficient is deduced, which is related to the driving frequency and the geometrical parameters of the EMAT’s meander coil, and lays a theoretical foundation for exactly analyzing the selective generation of Lamb waves with EMATs. The influences of the driving frequency on the mode expansion coefficient of ultrasonic Lamb waves are analyzed when the EMAT’s geometrical parameters are given. The numerical simulations and experimental examinations show that the ultrasonic Lamb wave modes can be effectively regulated (strengthened or restrained) by choosing an appropriate driving frequency of EMAT, with the geometrical parameters given. This result provides a theoretical and experimental basis for selectively generating a single and pure Lamb wave mode with EMATs. Project supported by the National Natural Science Foundation of China (Grant Nos. 11474361 and 11274388).

  18. Separation characteristics of alcohol from aqueous solution by ultrasonic atomization.

    Science.gov (United States)

    Yasuda, Keiji; Mochida, Kyosuke; Asakura, Yoshiyuki; Koda, Shinobu

    2014-11-01

    The generation rate of ultrasonically atomized droplets and the alcohol concentration in droplets were estimated by measuring the flow rate and the alcohol concentration of vapors from a bulk solution with a fountain. The effect of the alcohol concentration in the bulk solution on the generation rate of droplets and the alcohol concentration in droplets were investigated. The ultrasonic frequency was 2.4MHz, and ethanol and methanol aqueous solutions were used as samples. The generation rate of droplets for ethanol was smaller than that for methanol at the same alcohol molar fraction in the bulk solution. For both solutions, at low alcohol concentration in the bulk solution, the alcohol concentration in droplets was lower than that in vapors and the atomized droplets were visible. On the other side, at high concentration, the concentration in droplets exceeded that in vapors and the atomized droplets became invisible. These results could be explained that the alcohol-rich clusters in the bulk solution were preferentially atomized by ultrasonic irradiation. The concentration in droplets for ethanol was higher than that for methanol at low alcohol concentration because the amount of alcohol-rich clusters was larger. When the alcohol molar fraction was greater than 0.6, the atomized droplets almost consisted of pure alcohol.

  19. Universality in pure gravity mediation

    Energy Technology Data Exchange (ETDEWEB)

    Evans, Jason L.; Olive, Keith A. [University of Minnesota, William I. Fine Theoretical Physics Institute, School of Physics and Astronomy, Minneapolis, MN (United States); Ibe, Masahiro [University of Tokyo, ICRR, Kashiwa (Japan); University of Tokyo, Kavli IPMU, TODIAS, Kashiwa (Japan); Yanagida, Tsutomu T. [University of Tokyo, Kavli IPMU, TODIAS, Kashiwa (Japan)

    2013-07-15

    If low-energy supersymmetry is realized in nature, the apparent discovery of a Higgs boson with mass around 125 GeV suggests a supersymmetric mass spectrum in the TeV or multi-TeV range. Multi-TeV scalar masses are a necessary component of supersymmetric models with pure gravity mediation or in any model with strong moduli stabilization. Here, we show that full scalar mass universality remains viable as long as the ratio of Higgs vevs, tan{beta}, is relatively small (

  20. Toxicological evaluation of pure hydroxytyrosol.

    Science.gov (United States)

    Auñon-Calles, David; Canut, Lourdes; Visioli, Francesco

    2013-05-01

    Of all the phenolic constituents of olives and extra virgin olive oil, hydroxytyrosol is currently being actively exploited as a potential supplement or preservative to be employed in the nutraceutical, cosmeceutical, and food industry. In terms of safety profile, hydroxytyrosol has only been investigated as the predominant part of raw olive mill waste water extracts, due to the previous unavailability of appropriate quantities of the pure compound. We report the toxicological evaluation of hydroxytyrosol and, based on the results, propose a No Observed Adverse Effects Level (NOAEL) of 500mg/kg/d.

  1. Synthesis of Enantiomerically Pure Anthracyclinones

    Science.gov (United States)

    Achmatowicz, Osman; Szechner, Barbara

    The anthracycline antibiotics are among the most important clinical drugs used in the treatment of human cancer. The search for new agents with improved therapeutic efficacy and reduced cardiotoxicity stimulated considerable efforts in the synthesis of new analogues. Since the biological activity of anthracyclines depends on their natural absolute configuration, various strategies for the synthesis of enantiomerically pure anthracyclinones (aglycones) have been developed. They comprise: resolution of racemic intermediate, incorporation of a chiral fragment derived from natural and non-natural chiral pools, asymmetric synthesis with the use of a chiral auxiliary or a chiral reagent, and enantioselective catalysis. Synthetic advances towards enantiopure anthracyclinones reported over the last 17 years are reviewed.

  2. Ultrasonic ash/pyrite liberation

    Energy Technology Data Exchange (ETDEWEB)

    Yungman, B.A.; Buban, K.S.; Stotts, W.F.

    1990-06-01

    The objective of this project was to develop a coal preparation concept which employed ultrasonics to precondition coal prior to conventional or advanced physical beneficiation processes such that ash and pyrite separation were enhanced with improved combustible recovery. Research activities involved a series of experiments that subjected three different test coals, Illinois No. 6, Pittsburgh No. 8, and Upper Freeport, ground to three different size fractions (28 mesh [times] 0, 200 mesh [times] 0, and 325 mesh [times] 0), to a fixed (20 kHz) frequency ultrasonic signal prior to processing by conventional and microbubble flotation. The samples were also processed by conventional and microbubble flotation without ultrasonic pretreatment to establish baseline conditions. Product ash, sulfur and combustible recovery data were determined for both beneficiation processes.

  3. Ultrasonic techniques for fluids characterization

    CERN Document Server

    Povey, Malcolm J W

    1997-01-01

    This book is a comprehensive and practical guide to the use of ultrasonic techniques for the characterization of fluids. Focusing on ultrasonic velocimetry, the author covers the basic topics and techniques necessaryfor successful ultrasound measurements on emulsions, dispersions, multiphase media, and viscoelastic/viscoplastic materials. Advanced techniques such as scattering, particle sizing, and automation are also presented. As a handbook for industrial and scientific use, Ultrasonic Techniques for Fluids Characterization is an indispensable guide to chemists and chemical engineers using ultrasound for research or process monitoring in the chemical, food processing, pharmaceutical, cosmetic, biotechnology,and fuels industries. Key Features * Appeals to anyone using ultrasound to study fluids * Provides the first detailed description of the ultrasound profiling technique for dispersions * Describes new techniques for measuring phase transitions and nucleation, such as water/ice and oil/fat * Presents the l...

  4. Pure dysarthria due to an insular infarction.

    Science.gov (United States)

    Hiraga, Akiyuki; Tanaka, Saiko; Kamitsukasa, Ikuo

    2010-06-01

    Cortical infarction presenting with pure dysarthria is rarely reported. Previous studies have reported pure dysarthria due to cortical stroke at the precentral gyrus or middle frontal gyrus. We report a 72-year-old man who developed pure dysarthria caused by an acute cortical infarction in the insular cortex. The role of the insula in language has been difficult to assess clinically because of the rarity of pure insular strokes. Our patient showed pure dysarthria without aphasia, indicating that pure dysarthria can be the sole manifestation of insular infarctions.

  5. In situ x-ray diffraction measurements of the capillary fountain jet produced via ultrasonic atomization

    Science.gov (United States)

    Yano, Yohko F.; Douguchi, Junya; Kumagai, Atsushi; Iijima, Takao; Tomida, Yukinobu; Miyamoto, Toshiaki; Matsuura, Kazuo

    2006-11-01

    In situ x-ray diffraction measurements were carried out for investigating the liquid structure in the ultrasonic fountain jet to consider the mechanism of the "ultrasonic ethanol separation" reported by Sato et al. [J. Chem. Phys. 114, 2382 (2001)]. For pure liquids (water and ethanol), it was found that the high frequency ultrasound does not affect the liquid structure microscopically. For the 20mol% ethanol-water mixture, the estimated ethanol mole fraction in the ultrasonic fountain jet by using the position of the main maximum in the x-ray diffraction profile coincided with that in the reservoir. This result suggests that the ethanol separation is not caused by any distorted liquid structure under the ultrasound irradiation and occurs when or after the generation of the liquid droplet mist.

  6. Combined rheological and ultrasonic study of alginate and pectin gels near the sol-gel transition.

    Science.gov (United States)

    Audebrand, Michel; Kolb, Max; Axelos, Monique A V

    2006-10-01

    The sol-gel transition of biopolymer mixtures has been investigated by rheological and ultrasonic measurements. A scaling analysis of the data was performed for both types of measurements. A gel time was determined from rheology for the pure pectin samples, and the data could be fitted to a universal scaling form near the transition point. Its critical exponents are in good agreement with the predictions of scalar percolation theory. In addition, the ultrasonic signal of the pectin samples close to the transition was analyzed in terms of a high-frequency scaling approach for the attenuation and the velocity. For the alginate samples and the mixtures, for which the gel point cannot be determined reliably from rheology, the ultrasonic measurements were analyzed using the same scaling form as for the pectin sample, thus providing a method for estimating the gel point, even in the absence of rheological data.

  7. Application of ultrasonic guided waves to the characterization of texture in metal sheets of cubic and hexagonal crystallites

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yan.

    1990-10-08

    Ultrasonic techniques have recently been applied to the texture characterization in polycrystalline aggregates of hexagonal crystals. The basis of this application lies in the relations between the elastic constants {bar C}{sub ij} of the aggregates, which can be inferred from ultrasonic wave velocity measurements, and the orientation distribution coefficients. This communication present such relations for aggregates which possess orthotopic material symmetry and hexagonal crystal symmetry for Voigt, Reuss, and Hill averaging methods in a unified and concise representation.

  8. Ultrasonics: Fundamentals, Technologies, and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Ensminger, Dale; Bond, Leonard J.

    2011-09-17

    This is a new edition of a bestselling industry reference. Discusses the science, technology, and applications of low and high power ultrasonics, including industrial implementations and medical uses. Reviews the basic equations of acoustics, starting from basic wave equations and their applications. New material on property determination, inspection of metals (NDT) and non-metals, imaging, process monitoring and control. Expanded discussion of transducers, transducer wave-fields, scattering, attenuation and measurement systems and models. New material that discusses high power ultrasonics - in particular using mechanical effects and sonochemistry, including applications to nano-materials. Examines diagnosis, therapy, and surgery from a technology and medical physics perspective.

  9. ABSOLUTELY E-PURE MODULES AND E-PURE SPLIT MODULES

    Institute of Scientific and Technical Information of China (English)

    Yan Hangyu

    2011-01-01

    We first introduce the concepts of absolutely E-pure modules and Epure split modules. Then, we characterize the IF rings in terms of absolutely E-pure modules. The E-pure split modules are also characterized.

  10. A finite element model of ultrasonic extrusion

    Energy Technology Data Exchange (ETDEWEB)

    Lucas, M [Department of Mechanical Engineering, University of Glasgow, G12 8QQ (United Kingdom); Daud, Y, E-mail: m.lucas@mech.gla.ac.u [College of Science and Technology, UTM City Campus, Kuala Lumpur (Malaysia)

    2009-08-01

    Since the 1950's researchers have carried out investigations into the effects of applying ultrasonic excitation to metals undergoing elastic and plastic deformation. Experiments have been conducted where ultrasonic excitation is superimposed in complex metalworking operations such as wire drawing and extrusion, to identify the benefits of ultrasonic vibrations. This study presents a finite element analysis of ultrasonic excitation applied to the extrusion of a cylindrical aluminium bar. The effects of friction on the extrusion load are reported for the two excitation configurations of radially and axially applied ultrasonic vibrations and the results are compared with experimental data reported in the literature.

  11. A finite element model of ultrasonic extrusion

    Science.gov (United States)

    Lucas, M.; Daud, Y.

    2009-08-01

    Since the 1950's researchers have carried out investigations into the effects of applying ultrasonic excitation to metals undergoing elastic and plastic deformation. Experiments have been conducted where ultrasonic excitation is superimposed in complex metalworking operations such as wire drawing and extrusion, to identify the benefits of ultrasonic vibrations. This study presents a finite element analysis of ultrasonic excitation applied to the extrusion of a cylindrical aluminium bar. The effects of friction on the extrusion load are reported for the two excitation configurations of radially and axially applied ultrasonic vibrations and the results are compared with experimental data reported in the literature.

  12. Investigation of Noise in Electronic Ultrasonic Systems

    Directory of Open Access Journals (Sweden)

    Paulius Adomavičius

    2011-03-01

    Full Text Available Noise models in ultrasonic control system have been investigated. Ultrasonic system channel consist of exciting generator, ultrasonic transducer, amplitude limiter, amplifier, low band filter and A/D converter. The ultrasonic transducers have been described as Von Hippel model, Van Dyke model or improved Van Dyke model. Advantages and disadvantages of these models are discussed in this paper. Noise models of amplitude limiter and linear operational amplifier are presented. The summary results of calculated noise spectral density of ultrasonic system channel have been presented.Article in Lithuanian

  13. Ethanol separation from ethanol-water solution by ultrasonic atomization and its proposed mechanism based on parametric decay instability of capillary wave

    Science.gov (United States)

    Sato, Masanori; Matsuura, Kazuo; Fujii, Toshitaka

    2001-02-01

    We show the experimental data of selective ethanol separation from ethanol-water solution, using ultrasonic atomization. Pure ethanol could be obtained directly from a solution with several mol% ethanol-water solution at 10 °C. This result can be explained in terms of parametric decay instability of capillary wave, in which high localization and accumulation of acoustic energy occur, leading to ultrasonic atomization. That is, parametric decay instability condenses the energy of longitudinal waves in a highly localized surface area of the capillary wave, and causes ultrasonic atomization.

  14. Small-angle x-ray scattering measurement of a mist of ethanol nanodroplets: An approach to understanding ultrasonic separation of ethanol-water mixtures

    Science.gov (United States)

    Yano, Yohko F.; Matsuura, Kazuo; Fukazu, Tetsuo; Abe, Fusatsugu; Wakisaka, Akihiro; Kobara, Hitomi; Kaneko, Kazuyuki; Kumagai, Atsushi; Katsuya, Yoshio; Tanaka, Masahiko

    2007-07-01

    Small-angle x-ray scattering measurements using a brilliant x-ray source revealed nanometer sized liquid droplets in a mist formed by ultrasonic atomization. Ultrasonic atomization of ethanol-water mixtures produced a combination of water-rich droplets of micrometer order and ethanol-rich droplets as small as 1nm, which is 10-3 times smaller than the predicted size. These sizes were also obtained for mists generated from the pure liquids. These results will help to clarify the mechanism of "ultrasonic ethanol separation," which has the potential to become an alternative to distillation.

  15. Moths produce extremely quiet ultrasonic courtship songs by rubbing specialized scales

    DEFF Research Database (Denmark)

    Nakano, Ryo; Skals, Niels; Takanashi, Takuma

    2008-01-01

    Insects have evolved a marked diversity of mechanisms to produce loud conspicuous sounds for efficient communication. However, the risk of eavesdropping by competitors and predators is high. Here, we describe a mechanism for producing extremely low-intensity ultrasonic songs (46 dB sound pressure...

  16. Aviation-oriented Micromachining Technology-Micro-ECM in Pure Water

    Institute of Scientific and Technical Information of China (English)

    Bao Huaiqian; Xu Jiawen; Li Ying

    2008-01-01

    This article proposes a precise and ecofriendly micromachining technology for aerospace application called electrochemical machining in pure water (PW-ECM). On the basis of the principles of water dissociation, a series of test setups and tests are devised and performed under different conditions. These tests explain the need for technological conditions realizing PW-ECM, and further explore the technological principles. The results from the tests demonstrate a successful removal of electrolytic slime by means of ultrasonic vibration of the workpiece. To ensure the stability and reliability of PW-ECM process, a new combined rnachining method of PW-ECM assisted with ultrasonic vibration (PW-ECM/USV) is devised. Trilateral and square cavities and holes as well as a group of English alphabets are worked out on a stainless steel plate. It is eonfirmed that PW-ECM will be probably an efficient new aviation precision machining method.

  17. Pure optical dynamical color encryption

    Science.gov (United States)

    Mosso, Fabian; Tebaldi, Myrian; Fredy Barrera, John; Bolognini, Néstor; Torroba, Roberto

    2011-07-01

    We introduce a way to encrypt-decrypt a color dynamical phenomenon using a pure optical alternative. We split the three basic chromatic channels composing the input, and then each channel is processed through a 4f encoding method and a theta modulation applied to the each encrypted frame in every channel. All frames for a single channel are multiplexed. The same phase mask is used to encode all the information. Unlike the usual procedure we do not multiplex the three chromatic channels into a single encoding media, because we want to decrypt the information in real time. Then, we send to the decoding station the phase mask and the three packages each one containing the multiplexing of a single channel. The end user synchronizes and decodes the information contained in the separate channels. Finally, the decoding information is conveyed together to bring the decoded dynamical color phenomenon in real-time. We present material that supports our concepts.

  18. 76 FR 69284 - Pure Magnesium From China

    Science.gov (United States)

    2011-11-08

    ... COMMISSION Pure Magnesium From China Determination On the basis of the record \\1\\ developed in the subject... order on pure magnesium from China would be likely to lead to continuation or recurrence of material... USITC Publication 4274 (October 2011), entitled Pure Magnesium from China: Investigation No....

  19. Non-bonded ultrasonic transducer

    Science.gov (United States)

    Eoff, J.M.

    1984-07-06

    A mechanically assembled non-bonded ultrasonic transducer includes a substrate, a piezoelectric film, a wetting agent, a thin metal electrode, and a lens held in intimate contact by a mechanical clamp. No epoxy or glue is used in the assembly of this device.

  20. A new ultrasonic method to detect chemical additives in branded milk

    Indian Academy of Sciences (India)

    S Mohanan; P G Thomas Panicker; Lilly Iype; M Laila; I Domini; R G Bindu

    2002-09-01

    A new ultrasonic method – thermoacoustic analysis – is reported for the detection of the added chemical preservatives in branded milk. The nature of variation and shift in the thermal response of the acoustic parameters specific acoustic impedance, adiabatic compressibility and Rao’s specific sound velocity for different samples of branded milk as compared to the chemical added pure milk are explained as due to the presence of chemicals in these branded samples.

  1. Experimental study on ultrasonic propagation in water-based bentonite slurry

    Institute of Scientific and Technical Information of China (English)

    LAN Kai; YAN Taining

    2009-01-01

    Drilling fluid is a common flushing medium used in pile foundation, geological drilling and petroleum drilling. Study on ultrasonic propagation properties in drilling fluid is of vital importance, not only for developing equipments to non-contact measuring concrete casting level for bored pile, but also for developing equipments considering drilling fluid as signal channel. The existence of clay particles makes the ultrasonic propagation and attenuation in drilling fluid much different from pure water. In order to know the relation among ultrasound frequency, slurry density and depth, a series of laboratory experiments about ultrasound propagation in water-based bentonite slurry were finished. Wavelet method was adopted to process the gained original waves of ultrasonic propagation in slurry, so we knew the velocity and attenuation coefficient of ultrasound propagated in different drilling fluids with different density. The first group experiments shows that with density of drilling fluid increase, ultrasonic velocity will decrease but attenuation coefficient will increase if ultrasonic frequency keep constant. The second group experiments shows that the power of ultrasound will intensify in small bore hole, the attenuation coefficient is much smaller than theoretical value.

  2. Dual Target Search is Neither Purely Simultaneous nor Purely Successive.

    Science.gov (United States)

    Cave, Kyle R; Menneer, Tamaryn; Nomani, Mohammad S; Stroud, Michael J; Donnelly, Nick

    2017-08-31

    Previous research shows that visual search for two different targets is less efficient than search for a single target. Stroud, Menneer, Cave and Donnelly (2012) concluded that two target colours are represented separately based on modeling the fixation patterns. Although those analyses provide evidence for two separate target representations, they do not show whether participants search simultaneously for both targets, or first search for one target and then the other. Some studies suggest that multiple target representations are simultaneously active, while others indicate that search can be voluntarily simultaneous, or switching, or a mixture of both. Stroud et al.'s participants were not explicitly instructed to use any particular strategy. These data were revisited to determine which strategy was employed. Each fixated item was categorised according to whether its colour was more similar to one target or the other. Once an item similar to one target is fixated, the next fixated item is more likely to be similar to that target than the other, showing that at a given moment during search, one target is generally favoured. However, the search for one target is not completed before search for the other begins. Instead, there are often short runs of one or two fixations to distractors similar to one target, with each run followed by a switch to the other target. Thus, the results suggest that one target is more highly weighted than the other at any given time, but not to the extent that search is purely successive.

  3. Decryption of pure-position permutation algorithms

    Institute of Scientific and Technical Information of China (English)

    赵晓宇; 陈刚; 张亶; 王肖虹; 董光昌

    2004-01-01

    Pure position permutation image encryption algorithms, commonly used as image encryption investigated in this work are unfortunately frail under known-text attack. In view of the weakness of pure position permutation algorithm,we put forward an effective decryption algorithm for all pure-position permutation algorithms. First, a summary of the pure position permutation image encryption algorithms is given by introducing the concept of ergodic matrices. Then, by using probability theory and algebraic principles, the decryption probability of pure-position permutation algorithms is verified theoretically; and then, by defining the operation system of fuzzy ergodic matrices, we improve a specific decryption al-gorithm. Finally, some simulation results are shown.

  4. Rapid bonding enhancement by auxiliary ultrasonic actuation for the fabrication of cyclic olefin copolymer (COC) microfluidic devices

    Science.gov (United States)

    Yu, H.; Tor, S. B.; Loh, N. H.

    2014-11-01

    Thermal compression bonding is a straightforward, inexpensive and widely used method for enclosing open microchannels in thermoplastic microfluidic devices. It is advantageous over adhesive, solvent and grafting bonding methods in retaining material homogeneity. However, the trade-off between high bond strength and low microchannel deformation is always a crucial consideration in thermal compression bonding. In this study, an effective method for improving bond strength while retaining the microchannel integrity with negligible distortion is proposed and analyzed. Longitudinal ultrasonic actuation was applied to the preheated cyclic olefin copolymer (COC) substrates to achieve accelerated and enhanced bonding with an ultrasonic welding system. Intimate contact between the bonding surfaces before the ultrasonic actuation was found to be an important prior condition. With improper contact, several bonding defects would occur, such as voids, localized spot melting and edge melting. Under auxiliary ultrasonic vibration, within 10 s, the bond strength developed at the bonding interface could be dramatically improved compared with those achieved without ultrasonic actuation. The enhanced bond strength obtained at a preheating temperature of 20 °C lower than its Tg could be comparable to the strength for pure thermal compression at 5 °C higher than its Tg. It is believed that the ultrasonic energy introduced could elevate the interfacial temperature and facilitate the interdiffusion of molecular chain segments at the interface, consequently resulting in rapidly enhanced bonding. Also, the microchannel distortion after ultrasonic actuation was found to be satisfactory—another important requirement. From dynamic mechanical analysis, the glass transition temperature of COC was found to increase with increasing frequency, and the temperature of the bulk polymer under ultrasonic actuation was still well under Tg; therefore the deformation is minor under ultrasonic

  5. Decreased approach behavior and nucleus accumbens immediate early gene expression in response to Parkinsonian ultrasonic vocalizations in rats

    OpenAIRE

    2015-01-01

    Many individuals with Parkinson disease (PD) have difficulty producing normal speech and voice, resulting in problems with interpersonal communication and reduced quality of life. Translational animal models of communicative dysfunction have been developed to assess disease pathology. However, it is unknown whether acoustic feature changes associated with vocal production deficits in these animal models lead to compromised communication. In rodents, male ultrasonic vocalizations (USVs) have a...

  6. Bringing Planctomycetes into pure culture

    Directory of Open Access Journals (Sweden)

    Olga Maria Lage

    2012-12-01

    Full Text Available Planctomycetes have been known since the description of Planctomyces bekefii by Gimesi at the beginning of the twentieth century (1924, although the first axenic cultures were only obtained in the 1970s. Since then, eleven genera with fourteen species have been validly named and five candidatus genera belonging to the anaerobic ammonium oxidation, anammox bacteria have also been discovered. However, Planctomycetes diversity is much broader than these numbers indicate, as shown by environmental molecular studies. In recent years the authors have attempted to isolate and cultivate additional strains of Planctomycetes. This paper provides a summary of the isolation work that was carried out to obtain in pure culture Planctomycetes from several environmental sources. The following strains and planctomycetes have been successfully isolated: two freshwater strains from the sediments of an aquarium, which were described as a new genus and species, Aquisphaera giovannonii; several Rhodopirellula strains from the sediments of a water treatment recycling tank of a marine fish farm; and more than 140 planctomycetes from the biofilm community of macroalgae. This collection comprises several novel taxa that are being characterized and described. Improvements in the isolation methodology were made in order to optimize and enlarge the number of Planctomycetes isolated from the macroalgae. The existence of an intimate and an important relationship between planctomycetes and macroalgae reported before by molecular studies is therefore supported by culture dependent methods.

  7. Isomerically Pure Tetramethylrhodamine Voltage Reporters.

    Science.gov (United States)

    Deal, Parker E; Kulkarni, Rishikesh U; Al-Abdullatif, Sarah H; Miller, Evan W

    2016-07-27

    We present the design, synthesis, and application of a new family of fluorescent voltage indicators based on isomerically pure tetramethylrhodamines. These new Rhodamine Voltage Reporters, or RhoVRs, use photoinduced electron transfer (PeT) as a trigger for voltage sensing, display excitation and emission profiles in the green to orange region of the visible spectrum, demonstrate high sensitivity to membrane potential changes (up to 47% ΔF/F per 100 mV), and employ a tertiary amide derived from sarcosine, which aids in membrane localization and simultaneously simplifies the synthetic route to the voltage sensors. The most sensitive of the RhoVR dyes, RhoVR 1, features a methoxy-substituted diethylaniline donor and phenylenevinylene molecular wire at the 5'-position of the rhodamine aryl ring, exhibits the highest voltage sensitivity to date for red-shifted PeT-based voltage sensors, and is compatible with simultaneous imaging alongside green fluorescent protein-based indicators. The discoveries that sarcosine-based tertiary amides in the context of molecular-wire voltage indicators prevent dye internalization and 5'-substituted voltage indicators exhibit improved voltage sensitivity should be broadly applicable to other types of PeT-based voltage-sensitive fluorophores.

  8. Effect of Ultrasonic Frequency on Lactic Acid Fermentation Promotion by Ultrasonic Irradiation

    Science.gov (United States)

    Shimada, Tadayuki; Ohdaira, Etsuzo; Masuzawa, Nobuyoshi

    2004-05-01

    The authors have been researching the promotion of lactic acid fermentation by ultrasonic irradiation. In the past research, it was proven that ultrasonic irradiation is effective in the process of fermentation, and the production of yoghurt and kefir was promoted. In this study, the effect of the ultrasonic frequency in this fermentation process was examined. In the frequency range of this study, it was found that the action of fermentation promotion was exponentially proportionate to the irradiated ultrasonic frequency.

  9. Computer-controlled Sophisticated Ultrasonic Cleaner

    Directory of Open Access Journals (Sweden)

    H. Muthurajan

    2007-01-01

    Full Text Available The significant advantage of ultrasonic cleaning technique is the abilities to clean the delicateand complex shape materials without damaging their surfaces quickly. Ultrasonic cleaners havefound increasing applications in a variety of industries because these offer an environmentallygood alternative to ozone-depleting compounds and hazardous solvents. Also, ultrasonicvibration is one of the methods for chemical synthesis (chemical reaction and of yieldenhancement of chemical engineering process. Consequently, there is a need to developmultipurpose ultrasonic cleaner/vibrator using computer control, which can be used to set thevarious performance parameter of ultrasonic vibrator such as frequency, duty cycle, continuous/pulsed mode, duration of operation, and thermal profile of tank during the process. An ultrasoniccleaner was developed using an oscillator circuit and the duration of oscillator circuit functioningcan be set through the computer. Computerised ultrasonic cleaner using indigenously madepiezoceramic transducers and their advantages over the conventional ultrasonic cleaners are discussed.

  10. DEGASSING OF ALUMINUM A356 ALLOY USING ULTRASONIC VIBRATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Hanbing [University of Tennessee, Knoxville (UTK); Meek, Thomas T. [University of Tennessee, Knoxville (UTK); Han, Qingyou [ORNL

    2007-01-01

    In order to investigate the effects of ultrasonic vibration on degassing of aluminum alloys, three experimental systems have been designed and built: one for ultrasonic degassing in open air, one for ultrasonic degassing under reduced pressure, and one for ultrasonic degassing with a purging gas. Experiments were first carried out in air to test degassing using ultrasonic vibration alone. The limitations with ultrasonic degassing were outlined. Further experiments were then performed under reduced pressures and in combination with purging argon gas. Experimental results suggest that ultrasonic vibration alone is efficient for degassing a small volume of melt. Ultrasonic vibration can be used for assisting vacuum degassing, making vacuum degassing much faster than that without using ultrasonic vibration. Ultrasonically assisted argon degassing is the fastest method for degassing among the three methods tested in this research. More importantly, dross formation during ultrasonically assisted argon degassing is much less than that during argon degassing. The mechanisms of ultrasonic degassing are discussed.

  11. BSP的纯Java实现%Pure Java Implementation of BSP

    Institute of Scientific and Technical Information of China (English)

    孟睿; 李国平; 董景毅; 童维勤

    2001-01-01

    With the wide acceptance of the computing concept of cluster-based or cluster-of-clusters computing, network-based high performance computing is gaining increasing popularity among parallel computing community. Current parallel environments such as MPI (Message Passing Interface) or BSP (Bulk Synchronous Parallel) can not apply readily to heterogeneous computing platform. In order to exploit the maximum performance potential that a heterogeneous environment brings, we have made some experiments on implementing BSP in pure Java, a fully platform-independent language. The experimental results show that implementation of parallel libraries in Java is feasible and the performance is moderately acceptable. The paper describes our experiences in implementation of BSP in pure Java. Implementation and efficiency issues such as data transport, network communication, support thread, barrier synchronization and dynamic class loading mechanism are discussed in detail.

  12. BSP的纯Java实现%Pure Java Implementation of BSP

    Institute of Scientific and Technical Information of China (English)

    孟睿; 李国平; 董景毅; 童维勤

    2000-01-01

    With the wide acceptance of the computing concept of cluster-based or cluster-of-clusters computing, network-based high performance computing is gaining increasing popularity among parallel computing community. Current parallel environments such as MPI (Message Passing Interface) or BSP (Bulk Synchronous Parallel) can not apply readily to heterogeneous computing platform. In order to exploit the maximum performance potential that a heterogeneous environment brings, we have made some experiments on implementing BSP in pure Java, a fully platform-independent language. The experimental results show that implementation of parallel libraries in Java is feasible and the performance is moderately acceptable. The paper describes our experiences in implementation of BSP in pure Java. Implementation and efficiency issues such as data transport, network communication, support thread, barrier synchronization and dynamic class loading mechanism are discussed in detail.

  13. Exact and Asymptotic Measures of Multipartite Pure State Entanglement

    CERN Document Server

    Bennett, C H; Rohrlich, D E; Smolin, J A; Thapliyal, A V; Bennett, Charles H.; Popescu, Sandu; Rohrlich, Daniel; Smolin, John A.; Thapliyal, Ashish V.

    1999-01-01

    In an effort to simplify the classification of pure entangled states of multi (m) -partite quantum systems, we study exactly and asymptotically (in n) reversible transformations among n'th tensor powers of such states (ie n copies of the state shared among the same m parties) under local quantum operations and classical communication (LOCC). With regard to exact transformations, we show that two states whose 1-party entropies agree are either locally-unitarily (LU) equivalent or else LOCC-incomparable. Asymptotic transformations result in a simpler classification than exact transformations. We show that m-partite pure states having an m-way Schmidt decomposition are simply parameterizable, with the partial entropy across any nontrivial partition representing the number of standard ``Cat'' states (|0^m>+|1^m>) asymptotically interconvertible to the state in question. For general m-partite states, partial entropies across different partitions need not be equal, and since partial entropies are conserved by asymp...

  14. Pure variation and organic stratification.

    Science.gov (United States)

    Rosanvallon, Jérôme

    2012-09-01

    The fundamental problem posed by Darwin distinguishes his theory from any transformism of the past as well as any evolutionism to come: since variation is inherent to the living, it is a question of explaining, not at all why the living varies, but instead why the living does not vary in all directions to the point of constituting a continuum of forms varying ad infinitum. What limits and stabilizes this intrinsically unlimited variation, allowing certain forms to subsist and multiply to the detriment of others, is natural selection. This double principle of intrinsic variation/extrinsic selection constitutes a vector for the unification of reality that underlies Jean-Jacques Kupiec's ontophylogenesis as well as Deleuze and Guattari's global philosophy of Nature. Therefore, everything would potentially tend to incessantly vary. The work of Kupiec and others identifies an intrinsic random variation within ontogenesis itself. For Deleuze and Guattari, it is nothing but the figure, already selected by the organic stratum, of a more fundamental or pure variation. But, in fact, nothing really varies incessantly: everything undergoes a selective pressure according to which nothing subsists as such except what manages to endure through invariance (physical stratum) or reproduction (organic stratum). Thus, organic stratification only retains from variation what ensures and augments this reproduction. In this sense, every organism stratifies, i.e. submits to its imperative of subsistence and reproduction, a body without organs that varies in itself and always tends to escape the organism, for better (intensifications of life) or worse (cancerous pathologies). Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Lamb Wave Multitouch Ultrasonic Touchscreen.

    Science.gov (United States)

    Firouzi, Kamyar; Nikoozadeh, Amin; Carver, Thomas E; Khuri-Yakub, Butrus Pierre T

    2016-12-01

    Touchscreen sensors are widely used in many devices such as smart phones, tablets, and laptops with diverse applications. We present the design, analysis, and implementation of an ultrasonic touchscreen system that utilizes the interaction of transient Lamb waves with objects in contact with the screen. It attempts to improve on the existing ultrasound technologies, with the potential of addressing some of the weaknesses of the dominant technologies, such as the capacitive or resistive ones. Compared with the existing ultrasonic and acoustic modalities, among other advantages, it provides the capability of detecting several simultaneous touch points and also a more robust performance. The localization algorithm, given the hardware design, can detect several touch points with a very limited number of measurements (one or two). This in turn can significantly reduce the manufacturing cost.

  16. Ultrasonic disruption of algae cells

    Science.gov (United States)

    King, P. M.; Nowotarski, K.; Joyce, E. M.; Mason, T. J.

    2012-05-01

    During last decade there has been increasing interest in the production of sustainable fuels from microalgae (R.H. Wijffels and M.J. Barbosa, 2010; Singh et al 2011; D.H. Lee 2011). The aim of this project was to determine if algal cells can be ultrasonically disrupted to release lipids for biofuel production. Ultrasonic disruption of two unicellular algal species: Dunnaliella salina and Nannochloropsis oculata was investigated using a 20 kHz probe. Haemocytometer, optical density, UV-Vis, fluoro-spectrophotometer and confocal microscopy results demonstrated complete cell destruction of Dunaliella salina within 16 minutes of sonication. Results obtained for Nannochloropsis oculata differed in that ultrasound dispersed clumped cells with little or no cell disruption, as observed by haemocytometer and confocal microscopy analysis. However, UV-Visible and fluoro-spectrophotometer analysis indicated chlorophyll release following sonication, suggesting some cell disruption had occurred.

  17. Ultrasonic enhancement of battery diffusion.

    Science.gov (United States)

    Hilton, R; Dornbusch, D; Branson, K; Tekeei, A; Suppes, G J

    2014-03-01

    It has been demonstrated that sonic energy can be harnessed to enhance convection in Galvanic cells during cyclic voltammetry; however, the practical value of this approach is limited due to the lack of open volumes for convection patterns to develop in most batteries. This study evaluates the ability of ultrasonic waves to enhance diffusion in membrane separators commonly used in sandwich-architecture batteries. Studies include the measuring of open-circuit performance curves to interpret performances in terms of reductions in concentration overpotentials. The use of a 40 kHz sonicator bath can consistently increase the voltage of the battery and reduce overpotential losses up to 30%. This work demonstrates and quantifies battery enhancement due to enhanced diffusion made possible with ultrasonic energy.

  18. Integrated Ultrasonic-Photonic Devices

    DEFF Research Database (Denmark)

    Barretto, Elaine Cristina Saraiva

    This thesis deals with the modeling, design, fabrication and characterization of integrated ultrasonic-photonic devices, with particular focus on the use of standard semiconductor materials such as GaAs and silicon. The devices are based on the use of guided acoustic waves to modulate the light...... systems, all in search for paths to improve acousto-optic interaction. Some of the solutions proposed lead to enhancements of up to two orders of magnitude in the eciency of the device. The main aspects related to the design of the devices are discussed, including single-mode guidance, optical coupling......, integration and cost. The design proves to be robust towards fabrication and design tolerances. Several uses for this device are proposed, opening up a whole new group of applications for this class of integrated ultrasonic-photonic devices....

  19. Ultrasonic material hardness depth measurement

    Science.gov (United States)

    Good, Morris S.; Schuster, George J.; Skorpik, James R.

    1997-01-01

    The invention is an ultrasonic surface hardness depth measurement apparatus and method permitting rapid determination of hardness depth of shafts, rods, tubes and other cylindrical parts. The apparatus of the invention has a part handler, sensor, ultrasonic electronics component, computer, computer instruction sets, and may include a display screen. The part handler has a vessel filled with a couplant, and a part rotator for rotating a cylindrical metal part with respect to the sensor. The part handler further has a surface follower upon which the sensor is mounted, thereby maintaining a constant distance between the sensor and the exterior surface of the cylindrical metal part. The sensor is mounted so that a front surface of the sensor is within the vessel with couplant between the front surface of the sensor and the part.

  20. Ultrasonic attenuation in pearlitic steel.

    Science.gov (United States)

    Du, Hualong; Turner, Joseph A

    2014-03-01

    Expressions for the attenuation coefficients of longitudinal and transverse ultrasonic waves are developed for steel with pearlitic microstructure. This type of lamellar duplex microstructure influences attenuation because of the lamellar spacing. In addition, longitudinal attenuation measurements were conducted using an unfocused transducer with 10 MHz central frequency on the cross section of a quenched railroad wheel sample. The dependence of longitudinal attenuation on the pearlite microstructure is observed from the changes of longitudinal attenuation from the quenched tread surface to deeper locations. The results show that the attenuation value is lowest and relatively constant within the quench depth, then increases linearly. The experimental results demonstrate a reasonable agreement with results from the theoretical model. Ultrasonic attenuation provides an important non-destructive method to evaluate duplex microstructure within grains which can be implemented for quality control in conjunction with other manufacturing processes.

  1. Studies on Ultrasonic Spray Dryer (1)

    OpenAIRE

    井上, 昌夫

    1981-01-01

    Author has initiated research and development activities for a epochal ultrasonic spray dryer in order to obtain large quantities of droplets in uniform diameters, from which a practically applicable ultrasonic spray dryer would possibly be developed. Since the time Wood, Loomis et al. reported their experiments on atomization of liquids by ultrasonic power, research in this field is now widely attempted in many countries. In Japan, this field is being investigated by Ohno et al. Chiba, and M...

  2. Ultrasonic characterization of yogurt fermentation process

    OpenAIRE

    2012-01-01

    International audience; The objective of this work is to characterize the fermentation of yogurt based on an ultrasonic technique. Conventionally, the acidity of the yogurt is measured by a pH meter to determine the progress of fermentation. However, the pH meter should be cleaned and calibrated for each measurement and, therefore, this method is not practical. In this regard, ultrasonic techniques are fast, non-invasive and inexpensive. The measurement of ultrasonic parameters such as amplit...

  3. Littoral Subsonic Seismoacoustic Phenomena Ultrasonic Modeling

    Science.gov (United States)

    2016-06-07

    Littoral Subsonic Seismoacoustic Phenomena Ultrasonic Modeling Jacques R. Chamuel Sonoquest Advanced Ultrasonics Research P.O. Box 81153 Wellesley... variable water/air content, and benthic shelled animals leading to accurate acoustic modeling of littoral surficial layer and geophysical inversion...UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Sonoquest Advanced Ultrasonics Research ,P.O. Box 81153,Wellesley Hills,MA,02481-0001 8

  4. Analysis of the Rotary Ultrasonic Machining Mechanism

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Ultrasonic machining (USM) is considered as an effective method for machining hard and brittle materials such as glass, engineering ceramics, semiconductors, diamonds, metal composites and so on. However, the low material removal rate due to using abrasive slurry limits further application of USM. Rotary ultrasonic machining (rotary USM) superimposes rotational movement on the tool head that vibrates at ultrasonic frequency (20 kHz) simultaneously. The tool is made of mild steel coated or bonded with diamon...

  5. Degassing of Aluminum Alloys Using Ultrasonic Vibration

    Energy Technology Data Exchange (ETDEWEB)

    Meek, T. T.; Han, Q.; Xu, H.

    2006-06-01

    The research was intended to lead to a better fundamental understanding of the effect of ultrasonic energy on the degassing of liquid metals and to develop practical approaches for the ultrasonic degassing of alloys. The goals of the project described here were to evaluate core principles, establish a quantitative basis for the ultrasonic degassing of aluminum alloy melts, and demonstrate the application of ultrsaonic processing during ingot casting and foundry shape casting.

  6. The Influence of the Ultrasonic Intensity on the Cleaning Efficacy of Passive Ultrasonic Irrigation

    NARCIS (Netherlands)

    Jiang, Lei-Meng; Verhaagen, Bram; Versluis, Michel; Langedijk, Jelmer; Wesselink, Paul; van der Sluis, Lucas W. M.

    Introduction: It is not clear whether increasing the ultrasonic intensity would enhance the cleaning efficacy of passive ultrasonic irrigation (PUI) inside a root canal. The aim of this study was to evaluate the effect of the ultrasonic intensity on PUI to remove dentin debris and whether there is

  7. The Influence of the Ultrasonic Intensity on the Cleaning Efficacy of Passive Ultrasonic Irrigation

    NARCIS (Netherlands)

    Jiang, Lei-Meng; Verhaagen, B.; Versluis, Andreas Michel; Langedijk, Jelmer; Wesselink, Paul; van der Sluis, Lucas W.M.

    2011-01-01

    Introduction It is not clear whether increasing the ultrasonic intensity would enhance the cleaning efficacy of passive ultrasonic irrigation (PUI) inside a root canal. The aim of this study was to evaluate the effect of the ultrasonic intensity on PUI to remove dentin debris and whether there is

  8. The influence of the ultrasonic intensity on the cleaning efficacy of passive ultrasonic irrigation

    NARCIS (Netherlands)

    Jiang, L.M.; Verhaagen, B.; Versluis, M.; Langedijk, J.; Wesselink, P.; van der Sluis, L.W.

    2011-01-01

    Introduction: It is not clear whether increasing the ultrasonic intensity would enhance the cleaning efficacy of passive ultrasonic irrigation (PUI) inside a root canal. The aim of this study was to evaluate the effect of the ultrasonic intensity on PUI to remove dentin debris and whether there is

  9. The Influence of the Ultrasonic Intensity on the Cleaning Efficacy of Passive Ultrasonic Irrigation

    NARCIS (Netherlands)

    Jiang, Lei-Meng; Verhaagen, Bram; Versluis, Michel; Langedijk, Jelmer; Wesselink, Paul; van der Sluis, Lucas W. M.

    2011-01-01

    Introduction: It is not clear whether increasing the ultrasonic intensity would enhance the cleaning efficacy of passive ultrasonic irrigation (PUI) inside a root canal. The aim of this study was to evaluate the effect of the ultrasonic intensity on PUI to remove dentin debris and whether there is a

  10. Nonlinear Ultrasonic Phased Array Imaging

    Science.gov (United States)

    Potter, J. N.; Croxford, A. J.; Wilcox, P. D.

    2014-10-01

    This Letter reports a technique for the imaging of acoustic nonlinearity. By contrasting the energy of the diffuse field produced through the focusing of an ultrasonic array by delayed parallel element transmission with that produced by postprocessing of sequential transmission data, acoustic nonlinearity local to the focal point is measured. Spatially isolated wave distortion is inferred without requiring interrogation of the wave at the inspection point, thereby allowing nonlinear imaging through depth.

  11. Nonlinear ultrasonic phased array imaging

    OpenAIRE

    Potter, J N; Croxford, A.J.; Wilcox, P. D.

    2014-01-01

    This Letter reports a technique for the imaging of acoustic nonlinearity. By contrasting the energy of the diffuse field produced through the focusing of an ultrasonic array by delayed parallel element transmission with that produced by postprocessing of sequential transmission data, acoustic nonlinearity local to the focal point is measured. Spatially isolated wave distortion is inferred without requiring interrogation of the wave at the inspection point, thereby allowing nonlinear imaging t...

  12. Nonlinear ultrasonic phased array imaging.

    Science.gov (United States)

    Potter, J N; Croxford, A J; Wilcox, P D

    2014-10-03

    This Letter reports a technique for the imaging of acoustic nonlinearity. By contrasting the energy of the diffuse field produced through the focusing of an ultrasonic array by delayed parallel element transmission with that produced by postprocessing of sequential transmission data, acoustic nonlinearity local to the focal point is measured. Spatially isolated wave distortion is inferred without requiring interrogation of the wave at the inspection point, thereby allowing nonlinear imaging through depth.

  13. Ultrasonic Dynamic Vector Stress Sensor

    Science.gov (United States)

    Heyman, Joseph S.; Froggatt, Mark

    1992-01-01

    Stress inferred from measurements in specimens rather than in bonded gauges. Ultrasonic dynamic vector stress sensor (UDVSS) measures changes in dynamic directional stress occurring in material or structure at location touched by device when material or structure put under cyclic load. Includes phase-locked loop, synchronous amplifier, and contact probe. Useful among manufacturers of aerospace and automotive structures for stress testing and evaluation of designs.

  14. Microprocessor-controlled ultrasonic plethysmograph

    Science.gov (United States)

    Bhagat, P. K.; Wu, V. C.

    1981-01-01

    Safe, nonintrusive microprocessor system times ultrasonic pulses to measure limb cross-sectional area. Simple instrument requires no calibration and does not confine leg movement, making tests relating limb volume to activity level possible. Program considers more realistic geometries of human limb than circular cross-sections and monitors changes in area with great accuracy. Errors due to body temperature changes and timing roundoff are insignificant.

  15. Tame Kernels of Pure Cubic Fields

    Institute of Scientific and Technical Information of China (English)

    Xiao Yun CHENG

    2012-01-01

    In this paper,we study the p-rank of the tame kernels of pure cubic fields.In particular,we prove that for a fixed positive integer m,there exist infinitely many pure cubic fields whose 3-rank of the tame kernel equal to m.As an application,we determine the 3-rank of their tame kernels for some special pure cubic fields.

  16. Dissipation-induced pure Gaussian state

    CERN Document Server

    Koga, Kei

    2011-01-01

    This paper provides some necessary and sufficient conditions for a general Markovian Gaussian master equation to have a unique pure steady state. The conditions are described by simple matrix equations, thus they can be easily applied to the so-called environment engineering for pure Gaussian state preparation. In particular, it is shown that for any given pure Gaussian state we can actually construct a dissipative process yielding that state as the unique steady state.

  17. Predictive simulation of nonlinear ultrasonics

    Science.gov (United States)

    Shen, Yanfeng; Giurgiutiu, Victor

    2012-04-01

    Most of the nonlinear ultrasonic studies to date have been experimental, but few theoretical predictive studies exist, especially for Lamb wave ultrasonic. Compared with nonlinear bulk waves and Rayleigh waves, nonlinear Lamb waves for structural health monitoring become more challenging due to their multi-mode dispersive features. In this paper, predictive study of nonlinear Lamb waves is done with finite element simulation. A pitch-catch method is used to interrogate a plate with a "breathing crack" which opens and closes under tension and compression. Piezoelectric wafer active sensors (PWAS) used as transmitter and receiver are modeled with coupled field elements. The "breathing crack" is simulated via "element birth and death" technique. The ultrasonic waves generated by the transmitter PWAS propagate into the structure, interact with the "breathing crack", acquire nonlinear features, and are picked up by the receiver PWAS. The features of the wave packets at the receiver PWAS are studied and discussed. The received signal is processed with Fast Fourier Transform to show the higher harmonics nonlinear characteristics. A baseline free damage index is introduced to assess the presence and the severity of the crack. The paper finishes with summary, conclusions, and suggestions for future work.

  18. Ultrasonic Linear Motor with Anisotropic Composite

    Institute of Scientific and Technical Information of China (English)

    曾周末; 王新辉; 赵伯雷

    2004-01-01

    An idea to make up the vibrating body of ultrasonic motor with anisotropic composite is proposed and a linear piezoelectric motor is developed in this paper. Relative problems such as actuating mechanism, resonant frequency are discussed theoretically. According to the feature that impulse exists between the elastic body of composite ultrasonic linear motor and the base, an impulse analysis is presented to calculate the motor′s friction driving force and frictional conversion efficiency. The impulse analysis essentially explains the reason why the ultrasonic motor has great driving force, and can be applied to analyze the non-linear ultrasonic motor.

  19. Acoustic Communication for Medical Nanorobots

    CERN Document Server

    Hogg, Tad

    2012-01-01

    Communication among microscopic robots (nanorobots) can coordinate their activities for biomedical tasks. The feasibility of in vivo ultrasonic communication is evaluated for micron-size robots broadcasting into various types of tissues. Frequencies between 10MHz and 300MHz give the best tradeoff between efficient acoustic generation and attenuation for communication over distances of about 100 microns. Based on these results, we find power available from ambient oxygen and glucose in the bloodstream can readily support communication rates up to 10,000 bits/second between micron-sized robots. We discuss techniques, such as directional acoustic beams, that can increase this rate. The acoustic pressure fields enabling this communication are unlikely to damage nearby tissue, and short bursts at considerably higher power could be of therapeutic use.

  20. Moth hearing and sound communication

    DEFF Research Database (Denmark)

    Nakano, Ryo; Takanashi, Takuma; Surlykke, Annemarie

    2015-01-01

    Active echolocation enables bats to orient and hunt the night sky for insects. As a counter-measure against the severe predation pressure many nocturnal insects have evolved ears sensitive to ultrasonic bat calls. In moths bat-detection was the principal purpose of hearing, as evidenced by compar......, revealing a bias towards what humans can sense, when studying (acoustic) communication in animals....... by comparable hearing physiology with best sensitivity in the bat echolocation range, 20–60 kHz, across moths in spite of diverse ear morphology. Some eared moths subsequently developed sound-producing organs to warn/startle/jam attacking bats and/or to communicate intraspecifically with sound. Not only...... the sounds for interaction with bats, but also mating signals are within the frequency range where bats echolocate, indicating that sound communication developed after hearing by “sensory exploitation”. Recent findings on moth sound communication reveal that close-range (~ a few cm) communication with low...

  1. Preparation for Ultra High Pure Indium Metal for Optoelectronic Applications

    Directory of Open Access Journals (Sweden)

    Shashwat V. Joshi

    2014-11-01

    Full Text Available Ultra high pure Indium metal is extensively used in optoelectronic devices. Indium and its alloys become potential candidates in aerospace, defense and communication sectors. Purification of Indium has been done by Instrolec-200 Refiner followed by Directional Melting/ Freezing and Solidification Systems. Major targeted impurities are Metallic impurities Ag, Al, As, Bi, Ca, Cu, Fe, Ga, Ge, Mg, Pb, Sb, Si, Sn, and Zn. Purified Indium is characterized by analytical techniques Inductively Coupled Plasma- Optical Emission Spectrophotometry and Inductively Coupled Plasma- Mass Spectrometry.

  2. Fiber Optic Communications Technology. A Status Report.

    Science.gov (United States)

    Hull, Joseph A.

    Fiber optic communications (communications over very pure glass transmission channels of diameter comparable to a human hair) is an emerging technology which promises most improvements in communications capacity at reasonable cost. The fiber transmission system offers many desirable characteristics representing improvements over conventional…

  3. The Expansion Postponement in Pure Type Systems

    Institute of Scientific and Technical Information of China (English)

    宋方敏

    1997-01-01

    The expansion postponement problem in Pure Type Systems is an open problem raised by R.Pollack in 1992.In this paper,the author presents a set of necessary and sufficient conditions for this problem and a set of sufficient conditions for it.The author also gives some properties for pure typ systems without the expansion rule.

  4. Measuring the entanglement of bipartite pure states

    CERN Document Server

    Sancho, J M

    2000-01-01

    The problem of the experimental determination of the amount of entanglement of a bipartite pure state is addressed. We show that measuring a single observable does not suffice to determine the entanglement of a given unknown pure state of two particles. Possible minimal local measuring strategies are discussed and a comparison is made on the basis of their best achievable precision.

  5. Fundamentals of the pure spinor formalism

    NARCIS (Netherlands)

    Hoogeveen, J.

    2010-01-01

    This thesis presents recent developments within the pure spinor formalism, which has simplified amplitude computations in perturbative string theory, especially when spacetime fermions are involved. Firstly the worldsheet action of both the minimal and the non-minimal pure spinor formalism is derive

  6. Bubble colloidal AFM probes formed from ultrasonically generated bubbles.

    Science.gov (United States)

    Vakarelski, Ivan U; Lee, Judy; Dagastine, Raymond R; Chan, Derek Y C; Stevens, Geoffrey W; Grieser, Franz

    2008-02-05

    Here we introduce a simple and effective experimental approach to measuring the interaction forces between two small bubbles (approximately 80-140 microm) in aqueous solution during controlled collisions on the scale of micrometers to nanometers. The colloidal probe technique using atomic force microscopy (AFM) was extended to measure interaction forces between a cantilever-attached bubble and surface-attached bubbles of various sizes. By using an ultrasonic source, we generated numerous small bubbles on a mildly hydrophobic surface of a glass slide. A single bubble picked up with a strongly hydrophobized V-shaped cantilever was used as the colloidal probe. Sample force measurements were used to evaluate the pure water bubble cleanliness and the general consistency of the measurements.

  7. Beat-Frequency/Microsphere Medical Ultrasonic Imaging

    Science.gov (United States)

    Yost, William T.; Cantrell, John H.; Pretlow, Robert A., III

    1995-01-01

    Medical ultrasonic imaging system designed to provide quantitative data on various flows of blood in chambers, blood vessels, muscles, and tissues of heart. Sensitive enough to yield readings on flows of blood in heart even when microspheres used as ultrasonic contrast agents injected far from heart and diluted by circulation of blood elsewhere in body.

  8. Backward ray tracing for ultrasonic imaging

    NARCIS (Netherlands)

    Breeuwer, R.

    1990-01-01

    Focused ultrasonic beams frequently pass one or more media interfaces, strongly affecting the ultrasonic beamshape and focusing. A computer program, based on backward ray tracing was developed to compute the shape of a corrected focusing mirror. This shape is verified with another program; then the

  9. 21 CFR 870.2880 - Ultrasonic transducer.

    Science.gov (United States)

    2010-04-01

    ... structures. This device includes phased arrays and two-dimensional scanning transducers. (b) Classification... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultrasonic transducer. 870.2880 Section 870.2880...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Monitoring Devices § 870.2880 Ultrasonic...

  10. Ultrasonic fingerprinting by phased array transducer

    Science.gov (United States)

    Sednev, D.; Kataeva, O.; Abramets, V.; Pushenko, P.; Tverdokhlebova, T.

    2016-06-01

    Increasing quantity of spent nuclear fuel that must be under national and international control requires a novel approach to safeguard techniques and equipment. One of the proposed approaches is utilize intrinsic features of casks with spent fuel. In this article an application of a phased array ultrasonic method is considered. This study describes an experimental results on ultrasonic fingerprinting of austenitic steel seam weld.

  11. Ultrasonic fingerprinting by phased array transducer

    OpenAIRE

    Sednev, Dmitry Andreevich; Kataeva, O.; Abramets, V.; Pushenko, P.; Tverdokhlebova, T.

    2016-01-01

    Increasing quantity of spent nuclear fuel that must be under national and international control requires a novel approach to safeguard techniques and equipment. One of the proposed approaches is utilize intrinsic features of casks with spent fuel. In this article an application of a phased array ultrasonic method is considered. This study describes an experimental results on ultrasonic fingerprinting of austenitic steel seam weld.

  12. Broadband, High-Temperature Ultrasonic Transducer

    Science.gov (United States)

    Parker, F. Raymond; Winfree, William P.; Barrows, Danny A.

    1995-01-01

    Materials chosen for endurance at high temperatures and acoustic coupling and damping. Acoustic transducer designed to exhibit broad frequency response and to survive temperatures close to melting points of brazing alloys. Attached directly and continuously to hot object monitored ultrasonically: for example, it can be attached to relatively cool spot on workpiece during brazing for taking ultrasonic quality-control measurements.

  13. Backward ray tracing for ultrasonic imaging

    NARCIS (Netherlands)

    Breeuwer, R.

    1990-01-01

    Focused ultrasonic beams frequently pass one or more media interfaces, strongly affecting the ultrasonic beamshape and focusing. A computer program, based on backward ray tracing was developed to compute the shape of a corrected focusing mirror. This shape is verified with another program; then the

  14. Feasibility of transparent flexible ultrasonic haptic actuator

    Science.gov (United States)

    Akther, Asma; Kafy, Abdullahil; Kim, Hyun Chan; Kim, Jaehwan

    2016-04-01

    Ultrasonic haptics actuator is a device that can create a haptic feedback to user's hand. The modulation of ultrasonic frequency can give different textures to the users. In this study, a feasibility of the ultrasonic haptic actuator made on a flexible piezoelectric substrate is investigated. As the piezoelectric substrate helps to propagate flexural waves, a pair of interdigital transducer (IDT) with reflectors can produce standing waves, which can increase the vibrational displacement of the actuator. A pair of IDT pattern was fabricated on a piezoelectric polymer substrate. A finite element analysis is at first performed to design the actuator. A sinusoidal excitation voltage is applied on IDT electrodes at ultrasonic frequencies and the displacement waveforms are found. The displacement waveforms clearly represent how ultrasonic waves propagate through the piezoelectric substrate.

  15. Ultrasonic assessment of oil quality during frying.

    Science.gov (United States)

    Benedito, Jose; Mulet, Antonio; Velasco, J; Dobarganes, M Carmen

    2002-07-31

    In this paper, changes in ultrasonic properties during thermoxidation of virgin olive oil were studied. Samples of virgin olive oil were heated over different periods of time from 2 to 16 h at 200 degrees C. Oil degradation was characterized by means of physical and chemical changes, i.e., viscosity, color, polar compounds, polymers, and polar fatty acids. Ultrasonic measurements were carried out while the oil sample was cooled from 35 to 25 degrees C. It was found that velocity and attenuation measurements were related to viscosity measurements through a classical equation for viscous liquids. The ultrasonic measurements were also related to the percentages of polar compounds and polymers, which shows the feasibility of using ultrasonic properties to monitor oil quality. Nevertheless, as long as the ultrasonic measurements are temperature dependent, this variable must be controlled in order to obtain repetitive and reliable measurements.

  16. Passive wireless ultrasonic transducer systems

    Science.gov (United States)

    Zhong, C. H.; Croxford, A. J.; Wilcox, P. D.

    2014-02-01

    Inductive coupling and capacitive coupling both offer simple solutions to wirelessly probe ultrasonic transducers. This paper investigates the theory and feasibility of such system in the context of non-destructive evaluation (NDE) applications. Firstly, the physical principles and construction of an inductively coupled transducer system (ICTS) and a capacitively coupled transducer system (CCTS) are introduced. Then the development of a transmission line model with the measured impedance of a bonded piezoelectric ceramic disc representing a sensor attached to an arbitrary solid substrate for both systems is described. The models are validated experimentally. Several applications of CCTS are presented, such CCTS for the underwater and through-composite testing.

  17. Lase Ultrasonic Web Stiffness tester

    Energy Technology Data Exchange (ETDEWEB)

    Tim Patterson, Ph.D., IPST at Ga Tech

    2009-01-12

    The objective is to provide a sensor that uses non-contact, laser ultrasonics to measure the stiffness of paper during the manufacturing process. This will allow the manufacturer to adjust the production process in real time, increase filler content, modify fiber refining and as result produce a quality product using less energy. The sensor operates by moving back and forth across the paper web, at pre-selected locations firing a laser at the sheet, measuring the out-of-plane velocity of the sheet then using that measurement to calculate sheet stiffness.

  18. Calculations for Piezoelectric Ultrasonic Transducers

    DEFF Research Database (Denmark)

    Jensen, Henrik

    1986-01-01

    Analysis of piezoelectric ultrasonic transducers implies a solution of a boundary value problem, for a boay which consists of different materials, including a piezoelectric part. The problem is dynamic at frequencies, where a typical wavelength is somewhat less than the size of the body. Radiation...... and in particular the finite element method are considered. The finite element method is utilized for analysis of axisymmetric transducers. An explicit, fully piezoelectric, triangular ring element, with linear variations in displacememnt and electric potential is given. The influence of a fluid half-space is also...

  19. Characterization of Olive Oil by Ultrasonic and Physico-chemical Methods

    Science.gov (United States)

    Alouache, B.; Khechena, F. K.; Lecheb, F.; Boutkedjirt, T.

    Olive oil excels by its nutritional and medicinal benefits. It can be consumed without any treatment. However, its quality can be altered by inadequate storage conditions or if it is mixed with other kinds of oils. The objective of this work is to demonstrate the ability of ultrasonic methods to characterize and control olive oil quality. By using of a transducer of 2.25 MHz nominal frequency, in pulse echo mode, ultrasonic parameters, such as propagation velocity and attenuation,have been measured for pure olive oil and for its mixtures with sunflower oil at different proportions. Mechanical properties, such as density and viscosity, have also been determined. The results of ultrasonic measurements are consistent with those obtained by physico-chemical methods, such as rancidity degree, acid index, UV specific extinction coefficient and viscosity. They show that the ultrasonic method allows to distinguish between mixtures at different proportions. The study allows concluding that ultrasound techniques can be considered as a useful complement to existing physico-chemical analysis techniques.

  20. Effects of ultrasonic vibration on the micro-molding processing of polylactide.

    Science.gov (United States)

    Sacristán, Matías; Plantá, Xavier; Morell, Mireia; Puiggalí, Jordi

    2014-01-01

    A new ultrasonic micro-molding system was used to process polylactide (PLA) and fabricate reduced dimension specimens. Plasticization and molding of PLA were achieved by applying ultrasonic waves after feeding the polymer into a plasticizing chamber. Chemical and physical characteristics of processed PLA varied depending on the processing window (i.e. changes in ultrasonic wave amplitude between 14.2 and 48.1 μm and molding pressure between 0.5 in 6 bars). In terms of chemical effects, the application of ultrasound can lead to lower molecular weights (e.g. decreases of more than 45% in the weight average molecular weight), revealing partial degradation of the material. Also, the processed materials exhibited slightly higher thermal degradability than pure PLA because ultrasonic vibrations break molecular linkages and worsen the polymer structure. Finally, the processing conditions for the preparation of PLA specimens could be optimized without causing degradation and preserving structural characteristics and mechanical properties. Specifically, the use of an amplitude of 48.1 μm and a pressure of 3 bars gave samples with the same molecular weight as the raw material (i.e. 117,500 g/mol as opposed to 117,300 g/mol for Mw). Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Conformal pure radiation with parallel rays

    CERN Document Server

    Leistner, Thomas

    2011-01-01

    We define pure radiation metrics with parallel rays to be n-dimensional pseudo-Riemannian metrics that admit a parallel null line bundle K and whose Ricci tensor vanishes on vectors that are orthogonal to K. We give necessary conditions in terms of the Weyl, Cotton and Bach tensors for a pseudo-Riemannian metric to be conformal to a pure radiation metric with parallel rays. Then we derive conditions in terms of tractor calculus that are equivalent to the existence of a pure radiation metric with parallel rays in a conformal class. We also give an analogous result for n-dimensional pseudo-Riemannian pp-waves.

  2. Pure red cell aplasia and associated thymoma

    Directory of Open Access Journals (Sweden)

    Cristian Rosu

    2011-04-01

    Full Text Available Pure red cell aplasia is a rare cause of anemia, caused by an absence of red blood cell precursors in the bone marrow. It is usually a paraneoplastic syndrome, associated most commonly with large-cell granular lymphocyte leukemia but also thymoma. For patients who present both pure red cell aplasia and thymoma, thymectomy leads to an initial remission of the aplasia in 30% of cases. However, sustained remission may require the addition of medications such as corticosteroids, cyclospo­rine, or cyclophosphamide. We present a case of pure red cell aplasia associated with a thymoma in an otherwise healthy 80 year-old woman.

  3. Moth hearing and sound communication

    DEFF Research Database (Denmark)

    Nakano, Ryo; Takanashi, Takuma; Surlykke, Annemarie

    2015-01-01

    Active echolocation enables bats to orient and hunt the night sky for insects. As a counter-measure against the severe predation pressure many nocturnal insects have evolved ears sensitive to ultrasonic bat calls. In moths bat-detection was the principal purpose of hearing, as evidenced...... by comparable hearing physiology with best sensitivity in the bat echolocation range, 20–60 kHz, across moths in spite of diverse ear morphology. Some eared moths subsequently developed sound-producing organs to warn/startle/jam attacking bats and/or to communicate intraspecifically with sound. Not only...... the sounds for interaction with bats, but also mating signals are within the frequency range where bats echolocate, indicating that sound communication developed after hearing by “sensory exploitation”. Recent findings on moth sound communication reveal that close-range (~ a few cm) communication with low...

  4. Dynamics of ultrasonic additive manufacturing.

    Science.gov (United States)

    Hehr, Adam; Dapino, Marcelo J

    2017-01-01

    Ultrasonic additive manufacturing (UAM) is a solid-state technology for joining similar and dissimilar metal foils near room temperature by scrubbing them together with ultrasonic vibrations under pressure. Structural dynamics of the welding assembly and work piece influence how energy is transferred during the process and ultimately, part quality. To understand the effect of structural dynamics during UAM, a linear time-invariant model is proposed to relate the inputs of shear force and electric current to resultant welder velocity and voltage. Measured frequency response and operating performance of the welder under no load is used to identify model parameters. Using this model and in-situ measurements, shear force and welder efficiency are estimated to be near 2000N and 80% when welding Al 6061-H18 weld foil, respectively. Shear force and welder efficiency have never been estimated before in UAM. The influence of processing conditions, i.e., welder amplitude, normal force, and weld speed, on shear force and welder efficiency are investigated. Welder velocity was found to strongly influence the shear force magnitude and efficiency while normal force and weld speed showed little to no influence. The proposed model is used to describe high frequency harmonic content in the velocity response of the welder during welding operations and coupling of the UAM build with the welder. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Ultrasonic Characterization of Aerospace Composites

    Science.gov (United States)

    Leckey, Cara; Johnston, Patrick; Haldren, Harold; Perey, Daniel

    2015-01-01

    Composite materials have seen an increased use in aerospace in recent years and it is expected that this trend will continue due to the benefits of reduced weight, increased strength, and other factors. Ongoing work at NASA involves the investigation of the large-scale use of composites for spacecraft structures (SLS components, Orion Composite Crew Module, etc). NASA is also involved in work to enable the use of composites in advanced aircraft structures through the Advanced Composites Project (ACP). In both areas (space and aeronautics) there is a need for new nondestructive evaluation and materials characterization techniques that are appropriate for characterizing composite materials. This paper will present an overview of NASA's needs for characterizing aerospace composites, including a description of planned and ongoing work under ACP for the detection of composite defects such as fiber waviness, reduced bond strength, delamination damage, and microcracking. The research approaches include investigation of angle array, guided wave, and phase sensitive ultrasonic methods. The use of ultrasonic simulation tools for optimizing and developing methods will also be discussed.

  6. Floating Ultrasonic Transducer Inspection System and Method for Nondestructive Evaluation

    Science.gov (United States)

    Zalameda, Joseph N. (Inventor); Johnston, Patrick H. (Inventor)

    2016-01-01

    A method for inspecting a structural sample using ultrasonic energy includes positioning an ultrasonic transducer adjacent to a surface of the sample, and then transmitting ultrasonic energy into the sample. Force pulses are applied to the transducer concurrently with transmission of the ultrasonic energy. A host machine processes ultrasonic return pulses from an ultrasonic pulser/receiver to quantify attenuation of the ultrasonic energy within the sample. The host machine detects a defect in the sample using the quantified level of attenuation. The method may include positioning a dry couplant between an ultrasonic transducer and the surface. A system includes an actuator, an ultrasonic transducer, a dry couplant between the transducer the sample, a scanning device that moves the actuator and transducer, and a measurement system having a pulsed actuator power supply, an ultrasonic pulser/receiver, and a host machine that executes the above method.

  7. Techniques of Spectrum and Correlation Characteristics for Ultrasonic Ranging System

    Directory of Open Access Journals (Sweden)

    Tao Gao

    2013-09-01

    Full Text Available Both the spectrum and correlation characteristics are important in constructing excitation sequences to realize the multichannel ultrasonic sensors working together. For LFM excitation sequence, there should not be too many simultaneously fired ultrasonic sensors, because of the limited available frequency band of the ultrasonic ranging system. The optimized CFM excitation sequences are proposed to trigger multiple-user ultrasonic sensors in this paper. Comparing with the CFM excitation sequences without optimization, the NSGA-II based optimization CFM excitation sequences are more spectrally matched to the ultrasonic ranging system. Moreover, the ultrasonic crosstalk among multichannel sensors of an ultrasonic ranging system can be eliminated. Real experiments using an ultrasonic ranging system consisting of eight-channel SensComp 600 series electrostatic sensors excited with optimized CFM excitation sequences validate the suitability of the proposed method. The idea of optimizing CFM excitation sequences can also be used for the ultrasonic ranging system which has more than eight ultrasonic sensors.  

  8. Atomic model of liquid pure Fe

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Using a θ-θX-ray diffractometer, the liquid structure of pure Fewas investigated and the diffraction intensity, structure factor, pair distribution function as well as the coordination number and atomic distance were obtained. The experimental results showed that there was also a pre-peak on the curve of the structure factor of liquid pure Fe. The pre-peak is a mark of medium-range order in melts. According to the characteristics of pre-peak, an atomic model of liquid pure Fe is constructed, namely, the structure of liquid pure Fe is a combination of clusters consisting of bcc cells with shared vertexes and other atoms with random dense atom distribution.

  9. A control system of mobile navigation robot for precise spraying based ultrasonic detecting and ARM embedded technologies

    Science.gov (United States)

    Tang, Xiuying; Li, Cuiling; Wang, Xiu; Yue, Xinpeng; Peng, Yankun

    2011-06-01

    This paper described a control system of mobile navigation robot for precision spraying in greenhouse environment, which were composed of main control module, motor driving module, ultrasonic detecting module and wirless remote control module. The hard circuits of control system were built. The main control module used ARM7TDMI-S-based LPC2210 micro-processing controller. The motor driving module consisted of voltage amplifier circuit based SN74LS245N and DM74LS244N chips, RC filter circuit, and HM-YZ-30 DC brush motor driver. The ultrasonic detecting module consisted of four standard ultrasonic ranging modules which were arranged on the four sides around the mobile navigation robot, and used GM8125 chip to expand serial communication interfaces. An obstacle-avoiding strategy and its algorithm were proposed and the control programs of mobile navigation robot were programmed. The mobile navigation robot for spraying can realize the actions such as starting and stopping, forward and backward moving, accelerate and decelerate motion, and right and left turn. Finally, the functional experiments of the mobile navigation robot were conducted in the laboratory environment. The results showed that the ultrasonic detecting distance of the robot was 50.5mm-1832.0mm and detecting blind zone was less than 50mm, the ultrasonic detecting angle of individual ultrasonic detecting module of robot was similar to U-shaped and its vaule was about 45.66°, and the moving path of navigation robot was approximately linear.

  10. Entropy product measure for multipartite pure states

    Institute of Scientific and Technical Information of China (English)

    CAO Wancang; LIU Dan; PAN Feng; LONG Guilu

    2006-01-01

    An entanglement measure for multipartite pure states is formulated using the product of the von Neumann entropy of the reduced density matrices of the constituents.Based on this new measure, all possible ways of the maximal entanglement of the triqubit pure states are studied in detail and all types of the maximal entanglement have been culate the degree of entanglement, and an improvement is given in the area near the zero entropy.

  11. Diphenylhydantoin-induced pure red cell aplasia.

    Science.gov (United States)

    Rusia, Usha; Malhotra, Purnima; Joshi, Panul

    2006-01-01

    Pure red cell aplasia is an uncommon complication of diphenylhydantoin therapy. It has not been reported in Indian literature. Awareness of the entity helps in establishing the cause of anaemia in these patients and alerts the physicians to the need of comprehensive haematological monitoring in these patients. A case of 58-year-old male who developed pure red cell aplasia following three months of diphenylhydantoin therapy is reported here.

  12. Expander Graphs in Pure and Applied Mathematics

    OpenAIRE

    Lubotzky, Alexander

    2011-01-01

    Expander graphs are highly connected sparse finite graphs. They play an important role in computer science as basic building blocks for network constructions, error correcting codes, algorithms and more. In recent years they have started to play an increasing role also in pure mathematics: number theory, group theory, geometry and more. This expository article describes their constructions and various applications in pure and applied mathematics.

  13. Dark fermentation on biohydrogen production: Pure culture.

    Science.gov (United States)

    Lee, Duu-Jong; Show, Kuan-Yeow; Su, Ay

    2011-09-01

    Biohydrogen is regarded as an attractive future clean energy carrier due to its high energy content and environmental-friendly conversion. While biohydrogen production is still in the early stage of development, there have been a variety of laboratory- and pilot-scale systems developed with promising potential. This work presents a review of literature reports on the pure hydrogen-producers under anaerobic environment. Challenges and perspective of biohydrogen production with pure cultures are also outlined.

  14. Time difference based measurement of ultrasonic cavitations in wastewater treatment

    Institute of Scientific and Technical Information of China (English)

    朱昌平

    2016-01-01

    Intensity of cavitation is significant in ultrasonic wastewater treatment, but is complicated to measure.A time difference based method of ultrasonic cavitation measurement is proposed.The time differences at different powers of 495kHz ultrasonic are measured in experiment in comparison with conductimetric method.Simulation results show that time difference and electrical conductivity are both approximately positive proportional to the ultrasonic power.The degradation of PNP solution verifies the availability in wastewater treatment by using ultrasonic.

  15. Rehabilitation of pure alexia: A review

    Science.gov (United States)

    Starrfelt, Randi; Ólafsdóttir, Rannveig Rós; Arendt, Ida-Marie

    2013-01-01

    Acquired reading problems caused by brain injury (alexia) are common, either as a part of an aphasic syndrome, or as an isolated symptom. In pure alexia, reading is impaired while other language functions, including writing, are spared. Being in many ways a simple syndrome, one would think that pure alexia was an easy target for rehabilitation efforts. We review the literature on rehabilitation of pure alexia from 1990 to the present, and find that patients differ widely on several dimensions, such as alexia severity and associated deficits. Many patients reported to have pure alexia in the reviewed studies, have associated deficits such as agraphia or aphasia and thus do not strictly conform to the diagnosis. Few studies report clear and generalisable effects of training, none report control data, and in many cases the reported findings are not supported by statistics. We can, however, tentatively conclude that Multiple Oral Re-reading techniques may have some effect in mild pure alexia where diminished reading speed is the main problem, while Tacile-Kinesthetic training may improve letter identification in more severe cases of alexia. There is, however, still a great need for well-designed and controlled studies of rehabilitation of pure alexia. PMID:23808895

  16. Compound cavity theory of resonant phase modulation in laser self-mixing ultrasonic vibration measurement

    Science.gov (United States)

    Tao, Yufeng; Wang, Ming; Guo, Dongmei

    2016-07-01

    The theoretical basis of self-mixing interference (SMI) employing a resonant phase modulator is explored to prove its tempting advantages. The adopted method induces a pure phase carrier without increasing system complexity. A simple time-domain signal process is used to estimate modulation depth and precisely track vibrating trail, which promises the flexibility of measuring ultrasonic vibration regardless of the constraint of the Bessel functions. The broad bandwidth, low speckle noise, compact, safe, and easy operating SMI system obtains the best resolution of a poor reflection environment. Numerical simulation discusses the spectrum broadening and errors due to multiple reflections. Experimental results agree with theory coherently and are compared with laser Doppler vibration meter showing a dynamical error better than 20 nm in ultrasonic vibration measurement.

  17. Analysis and design of piezocomposite ultrasonic transducers using finite element technique and surface displacement profiles

    CERN Document Server

    Reynolds, P

    2000-01-01

    Ultrasonic transducers have found extensive applications in the fields of non-destructive testing, biomedicine, and SONAR. Piezocomposite ultrasonic transducers can offer significant advantages over their pure ceramic counterparts, but at the expense of increased manufacturing complexity and the introduction of additional resonant modes that may reduce transducer efficiency if the device is not carefully designed. Extensive work has been carried out over the last twenty years to characterise the behaviour of piezocomposite devices, resulting in many design guidelines, some of which are only applicable in a limited range of device structures. This Thesis presents a new theory of the generation of inter-pillar modes that is based upon the generation of Lamb waves in the piezocomposite plate. Through the use of finite element analysis and a scanning laser interferometer, the resonant mode displacement shapes of piezocomposite transducers are studied and analysed. Excellent correlation between modelled and experi...

  18. Testing Equivalence of Pure Quantum States and Graph States under SLOCC

    NARCIS (Netherlands)

    Briët, J.; Feder, D.L.; D'Souza, A.G.

    2010-01-01

    A set of necessary and sufficient conditions are derived for the equivalence of an arbitrary pure state and a graph state on n qubits under stochastic local operations and classical communication (SLOCC), using the stabilizer formalism. Because all stabilizer states are equivalent to graph states by

  19. Ultrasonic angle beam standard reflector. [ultrasonic nondestructive inspection

    Science.gov (United States)

    Berry, R. F., Jr. (Inventor)

    1985-01-01

    A method that provides an impression profile in a reference standard material utilized in inspecting critically stressed components with pulsed ultrasound is described. A die stamp having an I letter is used to impress the surface of a reference material. The die stamp is placed against the surface and struck with an inertia imparting member to impress the I in the reference standard material. Upset may appear on the surface as a result of the impression and is removed to form a smooth surface. The stamping and upset removal is repeated until the entire surface area of a depth control platform on the die stamp uniformly contacts the material surface. The I impression profile in the reference standard material is utilized for reflecting pulsed ultrasonic beams for inspection purposes.

  20. Fundamentals and applications of ultrasonic waves

    CERN Document Server

    Cheeke, J David N

    2002-01-01

    Ultrasonics. A subject with applications across all the basic sciences, engineering, medicine, and oceanography, yet even the broader topic of acoustics is now rarely offered at undergraduate levels. Ultrasonics is addressed primarily at the doctoral level, and texts appropriate for beginning graduate students or newcomers to the field are virtually nonexistent.Fundamentals and Applications of Ultrasonic Waves fills that void. Designed specifically for senior undergraduates, beginning graduate students, and those just entering the field, it begins with the fundamentals, but goes well beyond th

  1. Cytotoxicity of gold nanoparticles prepared by ultrasonic spray pyrolysis.

    Science.gov (United States)

    Rudolf, R; Friedrich, B; Stopić, S; Anžel, I; Tomić, S; Čolić, M

    2012-01-01

    The aim of this work was to study the cytotoxicity of different fractions of gold nanoparticles prepared by ultrasonic spray pyrolysis from gold scrap. The target cells were rat thymocytes, as a type of nonproliferating cells, and L929 mouse fibroblasts, as a type of continuous proliferating cells. Fractions 1 and 2, composed of pure gold nanoparticles, as determined by scanning electron microscopy with a combination of energy dispersive X-ray analysis, were nontoxic for thymocytes, but reduced moderately the proliferative activity of L929 cells. The inhibitory effect of fraction 2, containing particles smaller in size than fraction 1, was stronger. Fraction 3, composed of Au and up to 3% Cu was noncytotoxic for thymocytes, but was cytotoxic for L929 cells. Fraction 4, composed of Au and Ag nanoparticles, and fraction 5, composed of Au together with Cu, Ni, Zn, Fe, and In were cytotoxic for both thymocytes and L929 cells. These results suggest that USP enables the synthesis of pure gold nanoparticles with controlled size, even from gold scrap. However, microstructural analyses and biocompatibility testing are necessary for their proper selection from more cytotoxic gold nanoparticles, contaminated with other elements of gold alloys.

  2. Densities, Ultrasonic Speeds, Viscosities and Refractive Indices of Binary Mixtures of Benzene with Benzyl Alcohol,Benzonitrile, Benzoyl Chloride and Chlorobenzene at 303.15 K

    Institute of Scientific and Technical Information of China (English)

    ALI,A.; PANDEY,J.D.; SONI,N.K.; NAIN,A.K.; LAL,B.; CHAND,D.

    2005-01-01

    Densities, p, ultrasonic speeds, u, viscosities, η, and refractive indices, n, of pure benzene, benzyl alcohol (BA),benzonitrile (BN), benzoyl chloride (BC), chlorobenzene (CB) and their thirty six binary mixtures, with benzene as common component, were measured at 303.15 K over the entire mole fraction range. From these experimental data the values of deviations in ultrasonic speed, Au, isentropic compressibility, Δks, excess acoustic impedance, ZE, deviation in viscosity, Δη, and excess Gibbs free energy of activation of viscous flow, G*E, and partial molar isentropic compressibility, Kφ,2 of BA, BN, BC and CB in benzene were computed. The variation of these derived functions with composition of the mixtures suggested the increased cohesion (molecular order) in the solution and that interaction (A-B)>(A-A) or (B-B). Moreover, theoretical prediction of ultrasonic speed, viscosity and refractive index of all the four binary mixtures was made on the basis of empirical and semi-empirical relations by using the experimental values of the pure components. Comparison of theoretical results with the experimental values was made in order to assess the suitability of these relations in reproducing the experimental values of u, η and n. Also, molecular radii of pure liquids and the average molecular radii of binary mixtures were evaluated using the corresponding refractive indices of pure liquids and binary mixtures. The average molecular radii of binary mixtures were found to be additive with respect to mole fraction of the pure component.

  3. A mechanistic ultrasonic vibration amplitude model during rotary ultrasonic machining of CFRP composites.

    Science.gov (United States)

    Ning, Fuda; Wang, Hui; Cong, Weilong; Fernando, P K S C

    2017-04-01

    Rotary ultrasonic machining (RUM) has been investigated in machining of brittle, ductile, as well as composite materials. Ultrasonic vibration amplitude, as one of the most important input variables, affects almost all the output variables in RUM. Numerous investigations on measuring ultrasonic vibration amplitude without RUM machining have been reported. In recent years, ultrasonic vibration amplitude measurement with RUM of ductile materials has been investigated. It is found that the ultrasonic vibration amplitude with RUM was different from that without RUM under the same input variables. RUM is primarily used in machining of brittle materials through brittle fracture removal. With this reason, the method for measuring ultrasonic vibration amplitude in RUM of ductile materials is not feasible for measuring that in RUM of brittle materials. However, there are no reported methods for measuring ultrasonic vibration amplitude in RUM of brittle materials. In this study, ultrasonic vibration amplitude in RUM of brittle materials is investigated by establishing a mechanistic amplitude model through cutting force. Pilot experiments are conducted to validate the calculation model. The results show that there are no significant differences between amplitude values calculated by model and those obtained from experimental investigations. The model can provide a relationship between ultrasonic vibration amplitude and input variables, which is a foundation for building models to predict other output variables in RUM.

  4. Early communication deficits in the Shank1 knockout mouse model for autism spectrum disorder: Developmental aspects and effects of social context.

    Science.gov (United States)

    Sungur, A Özge; Schwarting, Rainer K W; Wöhr, Markus

    2016-06-01

    Alterations in SHANK genes were repeatedly reported in autism spectrum disorder (ASD). ASD is a group of neurodevelopmental disorders diagnosed by persistent deficits in social communication/interaction across multiple contexts, with restricted/repetitive patterns of behavior. To date, diagnostic criteria for ASD are purely behaviorally defined and reliable biomarkers have still not been identified. The validity of mouse models for ASD therefore strongly relies on their behavioral phenotype. Here, we studied communication by means of isolation-induced pup ultrasonic vocalizations (USV) in the Shank1 mouse model for ASD by comparing Shank1(-/-) null mutant, Shank1(+/-) heterozygous, and Shank1(+/+) wildtype littermate controls. The first aim of the present study was to evaluate the effects of Shank1 deletions on developmental aspects of communication in order to see whether ASD-related communication deficits are due to general impairment or delay in development. Second, we focused on social context effects on USV production. We show that Shank1(-/-) pups vocalized less and displayed a delay in the typical inverted U-shaped developmental USV emission pattern with USV rates peaking on postnatal day (PND) 9, resulting in a prominent genotype difference on PND6. Moreover, testing under social conditions revealed even more prominently genotype-dependent deficits regardless of the familiarity of the social context. As communication by definition serves a social function, introducing a social component to the typically nonsocial test environment could therefore help to reveal communication deficits in mouse models for ASD. Together, these results indicate that SHANK1 is involved in acoustic communication across species, with genetic alterations in SHANK1 resulting in social communication/interaction deficits. Autism Res 2016, 9: 696-709. © 2015 International Society for Autism Research, Wiley Periodicals, Inc. © 2015 International Society for Autism Research, Wiley

  5. Ultrasonic wave propagation on an inclined solid half-space partially immersed in a liquid

    Science.gov (United States)

    Dao, Cac Minh

    The interaction between a bounded ultrasonic beam and a liquid wedge over a solid half-space is studied theoretically as well as experimentally. A semi-analytical technique called Distributed Point Source Method (DPSM) is adopted for modeling the ultrasonic field in a wedge-shaped fluid structure on a solid half-space. This study is important for analyzing and understanding the propagation of ultrasonic waves used for underwater communications and inspections. A better understanding of the elastic wave propagation in water and in submerged marine strata near the seashore requires extensive investigations of such problem geometries. The semi-analytical technique used in this dissertation considers a bounded acoustic beam striking a fluid-solid interface between a fluid wedge and a solid half-space. Solution of this problem is beyond the scope of the currently available analytical methods when the beam is bounded. However, it is important to model the bounded beams because, in all underwater communications and inspections, bounded beams are used. Currently, only numerical method [Boundary Element Method (BEM) or Finite Element Method (FEM)] based packages (e.g., PZFlex) are in principle capable of modeling ultrasonic fields in such structures. However, these packages are not very accurate and are very CPU-intensive for high-frequency ultrasonic problems. At high frequencies, FEM- and BEM-based packages require huge amount of computation memory and time for their executions that the DPSM technique can avoid. The effect of the angle variation between the fluid-solid interface and the fluid wedge on the wave propagation characteristics is studied and presented.

  6. Ultrasonic attenuation in cuprate superconductors

    Indian Academy of Sciences (India)

    T Gupta; D M Gaitonde

    2002-05-01

    We calculate the longitudinal ultrasonic attenuation rate (UAR) in clean d-wave superconductors in the Meissner and the mixed phases. In the Meissner phase we calculate the contribution of previously ignored processes involving the excitation of a pair of quasi-holes or quasi-particles. There is a contribution ∝ in the regime B ≪ F ≪ 0 and a contribution ∝ 1/ in the regime F ≪ B ≪ 0. We find that these contributions to the UAR are large and cannot be ignored. In the mixed phase, using a semi-classical description, we calculate the electronic quasi-particle contribution to the UAR which at very low , has a independent term proportional to $\\sqrt{H}$.

  7. Ultrasonic Characterization of Glass Beads

    Science.gov (United States)

    Lassila, I.; Siiriä, S.; Gates, F. K.; Hæggström, E.

    2008-02-01

    We report on the progress in developing a method for an in-line granule size measurement using ultrasonic through transmission method. The knowledge of granule size is important in the production of pharmaceutical dosage forms where the current optical and rheological methods have limitations such as fouling of the optical windows. The phase velocity of a wave propagated through interstitial air between glass balls of 1, 2 and 10 mm in diameter was 254±5 m/s, 261±3 m/s and 320±9 m/s, respectively. The power spectral density of the received signals showed that high frequencies were attenuated more in case of smaller beads due to increased scattering.

  8. Cracks assessment using ultrasonic technology

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Maria Pia; Tomasella, Marcelo [OLDELVAL S.A. Oleoductos del Valle, Rio Negro (Argentina). Pipeline Integrity Dept.

    2005-07-01

    The goal of Oldelval Integrity Program is to prevent ruptures and leaks, developing strategies for a better handling of the integrity of our pipelines. In order to achieve it we have studied and modeled each process that involved in the integrity pipeline. Those processes are mainly based on defects reported by an internal inspection tool and supplied with field inspection and monitoring data. Years of evaluation, study and the continuous effort overturned towards a phenomenon that worries to the industry, as it is the SCC. Since 1998 up to 2004 SCC was included in the integrity program with some preventive maintenance programs. The accomplishment of the inspection based on ultrasound tools, is the culmination of years of evaluation and investigations supported by field digs and materials susceptibility. This paper describes Oldelval's results with ultrasonic crack detection tool, and how it can be reliably to detect SCC. (author)

  9. Ultrasonic atomization for spray drying: a versatile technique for the preparation of protein loaded biodegradable microspheres.

    Science.gov (United States)

    Bittner, B; Kissel, T

    1999-01-01

    Bovine serum albumin (BDA) loaded microspheres with a spherical shape and smooth surface structure were successfully prepared from poly(lactide-co-glycolide) using an ultrasonic nozzle installed in a Niro laboratory spray dryer. Process and formulation parameters were investigated with respect to their influence on microsphere characteristics, such as particle size, loading capacity, and release properties. Preparation of microspheres in yields of more than 50% was achieved using an ultrasonic atomizer connected to a stream of carrier air. Microsphere characteristics could be modified by changing several technological parameters. An increased polymer concentration of the feed generated larger particles with a significantly reduced initial release of the protein. Moreover, microspheres with a smooth surface structure were obtained from the organic polymer solution with the highest viscosity. Microparticles with a low BSA loading showed a large central cavity surrounded by a thin polymer layer in scanning electron microspheres. A high protein loading led to an enlargement of the shell layer, or even to dense particles without any cavities. A continuous in vitro release pattern of BSA was obtained from the particles with low protein loading. Glass transition temperatures (Tg) of the microspheres before and after lyophilization did not differ from those of the BSA loaded particles prepared by spray drying with a rotary atomizer. Analysis of the polymer by gel permeation chromatography indicated that ultrasonication had no effect on polymer molecular weight. Molecular weight and polydispersity of the pure polymer, placebo microspheres prepared by spray drying, and placebo microspheres prepared using the ultrasonic nozzle were in the same range. In conclusion, ultrasonic atomization represents a versatile and reliable technique for the production of protein loaded biodegradable microspheres without inducing a degradation of the polymer matrix. Particle characteristics

  10. Ultrasonic Histotripsy for Tissue Therapy

    Science.gov (United States)

    Pahk, K. J.; Dhar, D. K.; Malago, M.; Saffari, N.

    2015-01-01

    Hepatocyte transplantation has been considered and investigated as a promising and alternative method to liver transplantation for treating liver-based metabolic disorder in newborns over the past two decades. Although some clinical trials have been conducted and shown clinical benefits and outcomes, it is difficult to deliver and achieve a desired level of integration and transplantation of hepatocytes in the liver parenchyma. To overcome this problem, this work introduces an alternative method to a portal-infused-hepatocyte cell transplantation. To improve the level of engraftment of transplantable hepatocytes, these are injected directly into cavities generated by ultrasonic histotripsy. Histotripsy is an extracorporeal noninvasive technique which has been recently developed using high intensity focused ultrasound (HIFU) for inducing tissue fractionation with no coagulative necrosis. The exact mechanisms for the tissue fractionation are not well understood yet; but the possible mechanisms are thought to be a combination of nonlinear wave propagation effect, explosive bubble growth and ultrasonic atomization. The main objectives of this work are to demonstrate the feasibility of this new cell therapy and evaluate and distinguish between the different types of cavitation activity for either a thermally or a mechanically induced lesion. In the present work, numerical studies on the bubble dynamics (the Gilmore-Akulichev bubble model coupled with the Khokhlov-Zabolotskaya-Kuznetsov equation) and both ex- and in vivo liver experiments are conducted with histological analysis (haematoxylin and eosin stain). The numerical and the experimental results suggest that (a) the acoustic emissions emitted during the thermal ablation and the histotripsy exposure can be distinguished both numerically and experimentally and (b) the proposed cell therapy may potentially form an effective and safe clinical treatment for replacing and correcting disordered hepatocytes, although the

  11. Flexible Ultrasonic Phased-Array Probe

    Institute of Scientific and Technical Information of China (English)

    施克仁; 阙开良; 郭大勇

    2004-01-01

    In ultrasonic phased-array testing, most probes are rigid with fixed elements. However, when testing a cambered piece, a rigid probe cannot be used directly, but an ultrasonic chock or coupling media must be used, which adds cost and reduces the accuracy. The objective of this research was to improve the tests of cambered pieces. A flexible ultrasonic phased-array probe was developed to do the flexible phased-array testing. The key technologies in the flexible phased-array probe include the probe design and the phased-array control. A new method was developed to design the flexible probe according to the curvature of the piece and the test depth. The method includes the calculation of the element's height (he), the relative rotation angle ((e), the distance between the adjoining elements (de), and the element's effective testing range. A flexible ultrasonic phased-array probe has been developed using this method.

  12. Ultrasonically-assisted Thermal Stir Welding System

    Science.gov (United States)

    Ding, R. Jeffrey (Inventor)

    2014-01-01

    A welding head assembly has a work piece disposed between its containment plates' opposing surfaces with the work piece being maintained in a plastic state thereof at least in a vicinity of the welding head assembly's stir rod as the rod is rotated about its longitudinal axis. The welding head assembly and the work piece experience relative movement there between in a direction perpendicular to the rod's longitudinal axis as the work piece is subjected to a compressive force applied by the containment plates. A first source coupled to the first containment plate applies a first ultrasonic wave thereto such that the first ultrasonic wave propagates parallel to the direction of relative movement. A second source coupled to the second containment plate applies a second ultrasonic wave thereto such that the second ultrasonic wave propagates parallel to the direction of relative movement.propagates parallel to the direction of relative movement.

  13. Ultrasonic vibration for structural health monitoring

    Science.gov (United States)

    Liang, Y.; Yan, F.; Borigo, C.; Rose, J. L.

    2013-01-01

    Guided waves and vibration analysis are two useful techniques in Nondestructive Evaluation and Structural Health Monitoring. Bridging the gap between guided waves and vibration, a novel testing method ultrasonic vibration is demonstrated here. Ultrasonic vibration is capable to achieve defect detection sensitivity as ultrasonic guided waves, while maintaining the efficiency of traditional vibration in the way of adopting several sensors to cover the whole structure. In this new method, continuous guided wave energy will impinge into the structure to make the structure vibrate steadily. The steady state vibration is achieved after multiple boundary reflections of the continuous guided wave. In ultrasonic vibration experiments, annual array transducer is used as the actuator. The loading functions are tuned by the frequencies and phase delays among each transducer element. Experiments demonstrate good defect detection ability of by optimally selecting guided wave loadings.

  14. New pressure cell for ultrasonic measurements

    Science.gov (United States)

    Kepa, Michal; Huxley, Andrew; Kamenev, Konstantin

    2013-06-01

    Ultrasonic interferometry at high pressure remains a technical challenge as the small sample space requires the application of very high-frequency ultrasound. Here we present the design of a new cell developed specifically for ultrasonic measurements of single crystals at low temperatures (2K) and high pressures (5GPa). The design allows greater sample space (compared to a conventional diamond anvil cell) and simultaneous measurement of ultrasonic attenuation and velocities. Coupling the fine transducers to spherical sapphire anvils reduces background and enables different polarizations of the ultrasonic wave to be measured at the same pressure and temperature conditions. The results are used to deduce the elastic, electronic and magnetic properties of a crystal. The finite element analysis of the cell together with the pressure calibration curves and test data taken on UGe2 are presented.

  15. Introduction to Rheology for Ultrasonic Engineers

    Science.gov (United States)

    Ueda, Takanobu

    2008-05-01

    Here, I introduce the fundamental concept and methodology of rheology measurement especially to researchers in the field of ultrasonic engineering. Althogh we consider the material as fluid and characterize it in terms of viscosity accompanied by its complex part representing elasticity, ultrasonic spectroscopy regards the material as solid with elasticity, which determines ultrasonic velocity. Although these two research fields have contrary viewpoints, they share the purpose of the study, that is, to characterize the mechanical properties of the material as a function of frequency or shear rate and to reveal its mechanism and structure at the molecular level. In this paper, I show the basic methods of rheology measurement and analysis in relation to ultrasonic technology.

  16. Ultrasonic ranking of toughness of tungsten carbide

    Science.gov (United States)

    Vary, A.; Hull, D. R.

    1983-01-01

    The feasibility of using ultrasonic attenuation measurements to rank tungsten carbide alloys according to their fracture toughness was demonstrated. Six samples of cobalt-cemented tungsten carbide (WC-Co) were examined. These varied in cobalt content from approximately 2 to 16 weight percent. The toughness generally increased with increasing cobalt content. Toughness was first determined by the Palmqvist and short rod fracture toughness tests. Subsequently, ultrasonic attenuation measurements were correlated with both these mechanical test methods. It is shown that there is a strong increase in ultrasonic attenuation corresponding to increased toughness of the WC-Co alloys. A correlation between attenuation and toughness exists for a wide range of ultrasonic frequencies. However, the best correlation for the WC-Co alloys occurs when the attenuation coefficient measured in the vicinity of 100 megahertz is compared with toughness as determined by the Palmqvist technique.

  17. Nokia PureView oversampling technology

    Science.gov (United States)

    Vuori, Tero; Alakarhu, Juha; Salmelin, Eero; Partinen, Ari

    2013-03-01

    This paper describes Nokia's PureView oversampling imaging technology as well as the product, Nokia 808 PureView, featuring it. The Nokia PureView imaging technology is the combination of a large, super high resolution 41Mpix with high performance Carl Zeiss optics. Large sensor enables a pixel oversampling technique that reduces an image taken at full resolution into a lower resolution picture, thus achieving higher definition and light sensitivity. One oversampled super pixel in image file is formed by using many sensor pixels. A large sensor enables also a lossless zoom. If a user wants to use the lossless zoom, the sensor image is cropped. However, up-scaling is not needed as in traditional digital zooming usually used in mobile devices. Lossless zooming means image quality that does not have the digital zooming artifacts as well as no optical zooming artifacts like zoom lens system distortions. Zooming with PureView is also completely silent. PureView imaging technology is the result of many years of research and development and the tangible fruits of this work are exceptional image quality, lossless zoom, and superior low light performance.

  18. Structural anatomy of pure and hemianopic alexia.

    Science.gov (United States)

    Leff, A P; Spitsyna, G; Plant, G T; Wise, R J S

    2006-09-01

    The two most common types of acquired reading disorder resulting from damage to the territory of the dominant posterior cerebral artery are hemianopic and pure alexia. Patients with pronounced hemianopic alexia have a right homonymous hemianopia that encroaches into central or parafoveal vision; they read individual words well, but generate inefficient reading saccades when reading along a line of text. Patients with pure alexia also often have a hemianopia but are more disabled, making frequent errors on individual words; they have sustained damage to a brain region that supports efficient word identification. To investigate the differences in lesion site between hemianopic alexia and pure alexia groups, as rehabilitative techniques differ between the two conditions. High-resolution magnetic resonance images were obtained from seven patients with hemianopic alexia and from six patients with pure alexia caused by a left occipital stroke. The boundary of each lesion was defined and lesion volumes were then transformed into a standard stereotactic space so that regional comparisons could be made. The two patient groups did not differ in terms of damage to the medial left occipital lobe, but those with pure alexia had additional lateral damage to the posterior fusiform gyrus and adjacent tissue. Clinicians will be able to predict the type of reading disorder patients with left occipital lesions have from simple tests of reading speed and the distribution of damage to the left occipital lobe on brain imaging. This information will aid management decisions, including recommendations for reading rehabilitation.

  19. Pure plate bending in couple stress theories

    CERN Document Server

    Hadjesfandiari, Ali R; Dargush, Gary F

    2016-01-01

    In this paper, we examine the pure bending of plates within the framework of modified couple stress theory (M-CST) and consistent couple stress theory (C-CST). In this development, it is demonstrated that M-CST does not describe pure bending of a plate properly. Particularly, M-CST predicts no couple-stresses and no size effect for the pure bending of the plate into a spherical shell. This contradicts our expectation that couple stress theory should predict some size effect for such a deformation pattern. Therefore, this result clearly demonstrates another inconsistency of indeterminate symmetric modified couple stress theory (M-CST), which is based on considering the symmetric torsion tensor as the curvature tensor. On the other hand, the fully determinate skew-symmetric consistent couple stress theory (C-CST) predicts results for pure plate bending that tend to agree with mechanics intuition and experimental evidence. Particularly, C-CST predicts couple-stresses and size effects for the pure bending of the ...

  20. Ultrasonic intensification as a tool for enhanced microbial biofuel yields.

    Science.gov (United States)

    Naveena, Balakrishnan; Armshaw, Patricia; Tony Pembroke, J

    2015-01-01

    Ultrasonication has recently received attention as a novel bioprocessing tool for process intensification in many areas of downstream processing. Ultrasonic intensification (periodic ultrasonic treatment during the fermentation process) can result in a more effective homogenization of biomass and faster energy and mass transfer to biomass over short time periods which can result in enhanced microbial growth. Ultrasonic intensification can allow the rapid selective extraction of specific biomass components and can enhance product yields which can be of economic benefit. This review focuses on the role of ultrasonication in the extraction and yield enhancement of compounds from various microbial sources, specifically algal and cyanobacterial biomass with a focus on the production of biofuels. The operating principles associated with the process of ultrasonication and the influence of various operating conditions including ultrasonic frequency, power intensity, ultrasonic duration, reactor designs and kinetics applied for ultrasonic intensification are also described.

  1. Modeling and optimization of ultrasonic linear motors

    OpenAIRE

    Fernandez Lopez, José; Perriard, Yves

    2007-01-01

    Ultrasonic motors have received much attention these last years, in particular with regard to their modeling and their design principle. Their operating principle is based on piezoelectric ceramics that convert electrical energy into mechanical energy in the form of vibrations of an elastic body whose surface points perform an elliptic motion with a frequency in the ultrasonic range (≥ 20 kHz). The moving part, which is pressed against the vibrating body by a prestressing force, can move than...

  2. Wavelet Transform Signal Processing Applied to Ultrasonics.

    Science.gov (United States)

    1995-05-01

    THE WAVELET TRANSFORM IS APPLIED TO THE ANALYSIS OF ULTRASONIC WAVES FOR IMPROVED SIGNAL DETECTION AND ANALYSIS OF THE SIGNALS. In instances where...the mother wavelet is well defined, the wavelet transform has relative insensitivity to noise and does not need windowing. Peak detection of...ultrasonic pulses using the wavelet transform is described and results show good detection even when large white noise was added. The use of the wavelet

  3. Ultrasonic analysis of spherical composite test specimens

    Energy Technology Data Exchange (ETDEWEB)

    Brosey, W.D.

    1984-08-22

    Filament wound spherical test specimens have been examined ultrasonically as part of a program to determine the effectiveness of various nondestructive evaluation techniques for analysis of mechanical characteristics of a composite with enclosed geometry. The Kevlar-epoxy composite specimens contained simulated defect conditions which were located, and the extent of damage determined, using ultrasonic analysis. Effects of transducer frequency and signal parameters have been examined to determine optimum conditions for flaw detection. The data were displayed in rectangular and axonometric projection.

  4. Fundamentals and Applications of Ultrasonic Waves

    CERN Document Server

    Cheeke, J David N

    2012-01-01

    Designed specifically for newcomers to the field, this fully updated second edition begins with fundamentals and quickly advances beyond general wave concepts into an in-depth treatment of ultrasonic waves in isotropic media. Focusing on the physics of acoustic waves, their propagation, technology, and applications, this accessible overview of ultrasonics includes accounts of viscoelasticity and multiple scattering. It examines new technologies, including atomic force acoustic microscopy, lasers, micro-acoustics, and nanotechnology. In addition, it highlights both direct and indirect applicati

  5. Dynamic recrystallization behavior of commercial pure aluminum

    Institute of Scientific and Technical Information of China (English)

    LI Hui-zhong; ZHANG Xin-ming; CHEN Ming-an; LIU Zi-juan

    2006-01-01

    The flow stress feature and microstructure evolvement of a commercial pure aluminum were investigated by compression on Gleeble-1500 dynamic materials test machine. Optical microscopy (OM) and transmission electron microscopy (TEM) were applied to analyze the deformation microstructure of the commercial pure aluminum.The results show that the flow stress tends to be constant after a peak value and the dynamic recovery occurs when the deformation temperatures is 220 ℃ with the strain rate of 0.01 s-1; while the dynamic recrystallization occurs when the deformation temperature is higher than 380 ℃, and the flow stress exhibits a single peak at 460 ℃ with different strain rates from 0.001 s-1 to 1 s-1, and continuous dynamic recrystallization and geometric dynamic recrystallization occur during the hot compression of the commercial pure aluminum.

  6. Conclusive discrimination among N equidistant pure states

    Energy Technology Data Exchange (ETDEWEB)

    Roa, Luis; Hermann-Avigliano, Carla; Salazar, R. [Departamento de Fisica, Universidad de Concepcion, Barrio Universitario, Casilla 160-C, Concepcion (Chile); Klimov, A. B. [Departamento de Fisica, Universidad de Guadalajara, Revolucion 1500, 44420 Guadalajara, Jalisco (Mexico)

    2011-07-15

    We find the allowed complex overlaps for N equidistant pure quantum states. The accessible overlaps define a petal-shaped area on the Argand plane. Each point inside the petal represents a set of N linearly independent pure states and each point on its contour represents a set of N linearly dependent pure states. We find the optimal probabilities of success of discriminating unambiguously in which of the N equidistant states the system is. We show that the phase of the involved overlap plays an important role in the probability of success. For a fixed overlap modulus, the success probability is highest for the set of states with an overlap with phase equal to zero. In this case, if the process fails, then the information about the prepared state is lost. For states with a phase different from zero, the information could be obtained with an error-minimizing measurement protocol.

  7. Pure neuritic leprosy: Current status and relevance

    Directory of Open Access Journals (Sweden)

    P Narasimha Rao

    2016-01-01

    Full Text Available Pure neuritic leprosy has always been an enigma due to its clinical and management ambiguities. Although only the Indian Association of Leprologist's classification recognizes 'pure neuritic leprosy' as a distinct sub group of leprosy, cases nonetheless are reported from various countries of Asia, Africa, South America and Europe, indicating its global relevance. It is important to maintain pure neuritic leprosy as a subgroup as it constitutes a good percentage of leprosy cases reported from India, which contributes to more than half of global leprosy numbers. Unfortunately, a high proportion of these patients present with Grade 2 disability at the time of initial reporting itself due to the early nerve involvement. Although skin lesions are absent by definition, when skin biopsies were performed from the skin along the distribution of the affected nerve, a proportion of patients demonstrated leprosy pathology, revealing sub-clinical skin involvement. In addition on follow-up, skin lesions are noted to develop in up to 20% of pure neuritic leprosy cases, indicating its progression to manifest cutaneous disease. Over the decades, the confirmation of diagnosis of pure neuritic leprosy has been subjective, however, with the arrival and use of high-resolution ultrasonography (HRUS for nerve imaging, we have a tool not only to objectively measure and record the nerve thickening but also to assess the morphological alterations in the nerve including echo texture, fascicular pattern and vascularity. Management of pure neuritic leprosy requires multidrug therapy along with appropriate dose of systemic corticosteroids, for both acute and silent neuritis. Measures for pain relief, self-care of limbs and physiotherapy are important to prevent as well as manage disabilities in this group of patients.

  8. Pure neuritic leprosy: Current status and relevance.

    Science.gov (United States)

    Rao, P Narasimha; Suneetha, Sujai

    2016-01-01

    Pure neuritic leprosy has always been an enigma due to its clinical and management ambiguities. Although only the Indian Association of Leprologist's classification recognizes 'pure neuritic leprosy' as a distinct sub group of leprosy, cases nonetheless are reported from various countries of Asia, Africa, South America and Europe, indicating its global relevance. It is important to maintain pure neuritic leprosy as a subgroup as it constitutes a good percentage of leprosy cases reported from India, which contributes to more than half of global leprosy numbers. Unfortunately, a high proportion of these patients present with Grade 2 disability at the time of initial reporting itself due to the early nerve involvement. Although skin lesions are absent by definition, when skin biopsies were performed from the skin along the distribution of the affected nerve, a proportion of patients demonstrated leprosy pathology, revealing sub-clinical skin involvement. In addition on follow-up, skin lesions are noted to develop in up to 20% of pure neuritic leprosy cases, indicating its progression to manifest cutaneous disease. Over the decades, the confirmation of diagnosis of pure neuritic leprosy has been subjective, however, with the arrival and use of high-resolution ultrasonography (HRUS) for nerve imaging, we have a tool not only to objectively measure and record the nerve thickening but also to assess the morphological alterations in the nerve including echo texture, fascicular pattern and vascularity. Management of pure neuritic leprosy requires multidrug therapy along with appropriate dose of systemic corticosteroids, for both acute and silent neuritis. Measures for pain relief, self-care of limbs and physiotherapy are important to prevent as well as manage disabilities in this group of patients.

  9. Comparison of Diesel Engine Characteristic Using Pure Coconut Oil, Pure Palm Oil, and Pure Jatropha Oil as Fuel

    Directory of Open Access Journals (Sweden)

    Iman K. Reksowardojo

    2009-01-01

    Full Text Available Diesel engine can be operated on either pure plant oil (PPO oil or biodiesel. Biodiesel production process is expensive due to many stages of processes, while PPO has a lower cost of production, lower energy consumption, and simpler process. There are several potential biofuel resources in Indonesia such as coconut, palm, and jatropha. They are tropical plants with large amonts of their quantity. Experiment was conducted in 17 hours engine running test (endurance test with various operating cycle conditions. Test fuels are pure coconut oil (PCO, pure palm oil (PPaO, pure jatropha oil (PJO, and diesel fuel (DF as a datum. Each PPO blends with diesel fuel with composition 50%-volume. As a result, PCO has higher BSFC (10% before endurance test in comparison with diesel fuel, also PPaO (13% and PJO (27% show a similar condition. Surprisingly, all PPO have BSFC almost similar with DF after endurance test due to decreasing of engine components friction. On the other hand, PPO produces more uncompleted combustion than DF. Phosporus content has major responsibility of deposit growth. PCO, PPaO, and PJO result more engine deposits in comparison with DF, which accounts for 139,7%, 232,9%, and 288,9% respectively. Based on wear analysis, PCO has the best antiwear property among test fuels, whereas the worst is DF.

  10. Begging test: uma avaliação da graduação da comunicação visual entre cães sem raça definida, cães de raça (Golden Retrievers e humanos Begging test: an evaluation of the degree of visual communication between mixed, pure bred dogs (Golden Retrievers and humans

    Directory of Open Access Journals (Sweden)

    Edilberto Nobrega Martinez

    2011-04-01

    Full Text Available O begging test tem sido usado para testar a capacidade dos cães em interpretar a atenção humana. Pistas faciais, como o olhar e a posição da cabeça são os principais sinais na comunicação entre cães e humanos. Até o momento, a estrutura do begging test utilizado em pesquisas não permitiu verificar se há uma graduação na atenção. Desse modo, não é possível dizer se a cabeça e o olhar diretamente dirigidos (muita atenção ao cão aumentam o desempenho em relação a somente a posição da cabeça, mas sem olhar diretamente (pouca atenção ou cabeça plus olhar desviados (desatenção. Nesse sentido, um teste envolvendo 58 cães de raça pura (Golden Retrievers e mista foi realizado, nas três condições de atenção, com homens e mulheres estranhos aos animais servindo de sujeitos experimentais. Resultados demonstraram que independente da raça, do sexo dos cães ou do sexo das pessoas, os cães erraram pouco na condição de desatenção. Por outro lado, o desempenho dos cães não diferiu entre as condições de muita atenção e de pouca atenção, mas foi significativamente superior do que na condição de desatenção. Em conclusão, os cães são bons interpretadores da atenção humana, mas se baseiam em pistas mais relacionadas à posição da cabeça do que o olhar. Assim, sugere-se que não há uma graduação na interpretação da atenção de humanos em cães. O estímulo emocional gerado pelo olhar direto, sustentado entre animais sociais, pode explicar porque o olhar é evitado como pista da atenção humana em um teste com pessoas estranhas ao cão.The begging test has been used to test the ability of dogs to interprete human attention. Facial cues, such as gaze and head position are the main signs in the communication between humans and dogs. Yet, the structure of the begging test used in research did not allow checking whether there are graduations of attention. Thus, it's not possible to say if the head

  11. Minimal covariant observables identifying all pure states

    Energy Technology Data Exchange (ETDEWEB)

    Carmeli, Claudio, E-mail: claudio.carmeli@gmail.com [D.I.M.E., Università di Genova, Via Cadorna 2, I-17100 Savona (Italy); I.N.F.N., Sezione di Genova, Via Dodecaneso 33, I-16146 Genova (Italy); Heinosaari, Teiko, E-mail: teiko.heinosaari@utu.fi [Turku Centre for Quantum Physics, Department of Physics and Astronomy, University of Turku (Finland); Toigo, Alessandro, E-mail: alessandro.toigo@polimi.it [Dipartimento di Matematica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy); I.N.F.N., Sezione di Milano, Via Celoria 16, I-20133 Milano (Italy)

    2013-09-02

    It has been recently shown by Heinosaari, Mazzarella and Wolf (2013) [1] that an observable that identifies all pure states of a d-dimensional quantum system has minimally 4d−4 outcomes or slightly less (the exact number depending on d). However, no simple construction of this type of minimal observable is known. We investigate covariant observables that identify all pure states and have minimal number of outcomes. It is shown that the existence of this kind of observables depends on the dimension of the Hilbert space.

  12. Combined Cycle Fatigue Testing with Ultrasonic Frequency Component of S350 Steel Welded Joint

    Institute of Scientific and Technical Information of China (English)

    柳阳; 王东坡; 邓彩艳; 吴良晨; 尹丹青; 龚宝明

    2014-01-01

    A combined cycle fatigue (CCF) testing system with ultrasonic frequency component was developed to evaluate the CCF properties of S350 steel welded joints in this study. The fatigue testing results indicated that the S-N curves of CCF did not have fatigue limit, which agreed with those of pure high frequency fatigue of welded joints. The S-N curves showed that the CCF strength of welded joints dropped greatly with the increasing interaction between high and low frequency fatigue loading. An approximation design method of CCF was presented using amplitude envelope as the stress range.

  13. Experimental issues at ultrasonically aided micro-EDM of CoCr alloys

    Directory of Open Access Journals (Sweden)

    Marinescu Niculae

    2017-01-01

    Full Text Available The paper deals with researches of microtopography obtained at different working modes at ultrasonically aided micro-electrical discharge machining (μEDM+US and pure micro-EDM, using both commanded and relaxation pulses. Images of machined surface taken with scanning electron microscope were analyzed in correlation with chemical composition of samples detected by X rays spectrometer. This led to some explanations of material removal mechanism, aiming at improvement of process modelling and performances increase of μEDM+US.

  14. Remediation of Diesel Fuel Contaminated Sandy Soil using Ultrasonic Waves

    Directory of Open Access Journals (Sweden)

    Wulandari P.S.

    2010-01-01

    Full Text Available Ultrasonic cleaning has been used in industry for some time, but the application of ultrasonic cleaning in contaminated soil is just recently received considerable attention, it is a very new technique, especially in Indonesia. An ultrasonic cleaner works mostly by energy released from the collapse of millions of microscopic cavitations near the dirty surface. This paper investigates the use of ultrasonic wave to enhance remediation of diesel fuel contaminated sandy soil considering the ultrasonic power, soil particle size, soil density, water flow rate, and duration of ultrasonic waves application.

  15. Ultrasonic transducer chip assembly, ultrasound probe, ultrasonic imaging system and ultrasound assembly and probe manufacturing methods

    NARCIS (Netherlands)

    Weekamp, J.W.; Henneken, V.A.; Groenland, A.W.; Louwerse, M.C.

    2015-01-01

    Disclosed is an ultrasonic transducer assembly comprising an ultrasonic transducer chip (100) having a main surface comprising a plurality of ultrasound transducer elements (112) and a plurality of first contacts (120) for connecting to said ultrasound transducer elements; a contact chip (400) havin

  16. Spectroscopic ellipsometry, optical, structural and electrical investigation of sprayed pure and Sn-doped ZnO thin films

    OpenAIRE

    Attaf N.; Aida M.S.; Benhaliliba M.; Mokhtari H.; Ocak Y.

    2013-01-01

    In this work, we report the transparent pure and Sn-doped zinc oxide (ZnO). The films were deposited onto microscope glass substrate which was heated at 350±5C° by ultrasonic spray pyrolysis (U S P) deposition technique. The concentrations of Sn were selected within the range of 0-3% by step of 0.5% and the time deposition is kept at 5 min. A (002)-oriented wurtzite crystal structure was confirmed by X-rays patterns; and grain size varied within the range 7.37-14.84nm, and cristanillity is ca...

  17. Design of embedded endoscopic ultrasonic imaging system

    Science.gov (United States)

    Li, Ming; Zhou, Hao; Wen, Shijie; Chen, Xiodong; Yu, Daoyin

    2008-12-01

    Endoscopic ultrasonic imaging system is an important component in the endoscopic ultrasonography system (EUS). Through the ultrasonic probe, the characteristics of the fault histology features of digestive organs is detected by EUS, and then received by the reception circuit which making up of amplifying, gain compensation, filtering and A/D converter circuit, in the form of ultrasonic echo. Endoscopic ultrasonic imaging system is the back-end processing system of the EUS, with the function of receiving digital ultrasonic echo modulated by the digestive tract wall from the reception circuit, acquiring and showing the fault histology features in the form of image and characteristic data after digital signal processing, such as demodulation, etc. Traditional endoscopic ultrasonic imaging systems are mainly based on image acquisition and processing chips, which connecting to personal computer with USB2.0 circuit, with the faults of expensive, complicated structure, poor portability, and difficult to popularize. To against the shortcomings above, this paper presents the methods of digital signal acquisition and processing specially based on embedded technology with the core hardware structure of ARM and FPGA for substituting the traditional design with USB2.0 and personal computer. With built-in FIFO and dual-buffer, FPGA implement the ping-pong operation of data storage, simultaneously transferring the image data into ARM through the EBI bus by DMA function, which is controlled by ARM to carry out the purpose of high-speed transmission. The ARM system is being chosen to implement the responsibility of image display every time DMA transmission over and actualizing system control with the drivers and applications running on the embedded operating system Windows CE, which could provide a stable, safe and reliable running platform for the embedded device software. Profiting from the excellent graphical user interface (GUI) and good performance of Windows CE, we can not

  18. The development of recent high-power ultrasonic transducers for Near-well ultrasonic processing technology.

    Science.gov (United States)

    Wang, Zhenjun; Xu, Yuanming

    2017-07-01

    With the reduction of crude oil throughout the world, enhance oil recovery technology has become a major oil research topics, which can greatly increase the recovery ratio of the crude oil before the dawning of renewable energy era. Near-well ultrasonic processing technology, as one new method, has attracted more attention for Enhanced Oil Recovery due to its low cost, good applicability and no environmental pollution in recent rears. There are two important relevant aspects about Near-well ultrasonic processing technology: (a) how to enhance the oil flow through the rocks into the pumping pool and (b) how to reduce the oil viscosity so that it can be easier to pump. Therefore, how to design a high-power ultrasonic equipment with excellent performance is crucial for Near-well ultrasonic processing technology. In this paper, recent new high-power ultrasonic transducers for Near-well ultrasonic processing technology are summarized. Each field application of them are also given. The purpose of this paper is to provide reference for the further development of Near-well ultrasonic processing technology. With the reduction of crude oil throughout the world, enhance oil recovery technology has become a major oil research topics, which can greatly increase the recovery ratio of the crude oil before the dawning of renewable energy era. Near-well ultrasonic processing technology, as one new method, has attracted more attention for Enhanced Oil Recovery due to its low cost, good applicability and no environmental pollution in recent rears. There are two important relevant aspects about Near-well ultrasonic processing technology: (a) how to enhance the oil flow through the rocks into the pumping pool and (b) how to reduce the oil viscosity so that it can be easier to pump. Therefore, how to design a high-power ultrasonic equipment with excellent performance is crucial for Near-well ultrasonic processing technology. In this paper, recent new high-power ultrasonic transducers

  19. Pure word deafness and pure anarthria in a patient with frontotemporal dementia.

    Science.gov (United States)

    Iizuka, O; Suzuki, K; Endo, K; Fujii, T; Mori, E

    2007-04-01

    A 66-year-old right-handed man developed pure anarthria following pure word deafness. In addition to language disorders, his behavior gradually changed and finally included violence against his wife. Brain magnetic resonance imagings revealed atrophy of the left perisylvian area, which included the inferior half of the precentral gyrus and the upper portion of the superior temporal gyrus, consistent with frontotemporal dementia (FTD). It has been documented as either a disorder of expressive language or as an impaired understanding of word meaning. Unlike with pure anarthria, pure word deafness is not included in the clinical diagnostic current criteria for FTD. However, a large variety of language symptoms can appear in FTD according to the distribution of pathological changes in the frontotemporal cortices. This case suggests that pure word deafness could be a prodomal symptom of FTD.

  20. Satellite Communication.

    Science.gov (United States)

    Technology Teacher, 1985

    1985-01-01

    Presents a discussion of communication satellites: explains the principles of satellite communication, describes examples of how governments and industries are currently applying communication satellites, analyzes issues confronting satellite communication, links mathematics and science to the study of satellite communication, and applies…

  1. Are all maximally entangled states pure?

    CERN Document Server

    Cavalcanti, D; Terra-Cunha, M O

    2005-01-01

    In this Letter we study if all maximally entangled states are pure through several entanglement monotones. Our conclusions allow us to generalize the idea of monogamy of entanglement. Then we propose a polygamy of entanglement, which express that if a general multipartite state is maximally entangled it is necessarily factorized by any other system.

  2. Implicit Reading in Chinese Pure Alexia

    Science.gov (United States)

    Shan, Chunlei; Zhu, Renjing; Xu, Mingwei; Luo, Benyan; Weng, Xuchu

    2010-01-01

    A number of recent studies have shown that some patients with pure alexia display evidence of implicit access to lexical and semantic information about words that they cannot read explicitly. This phenomenon has not been investigated systematically in Chinese patients. We report here a case study of a Chinese patient who met the criteria for pure…

  3. Pure science and the problem of progress.

    Science.gov (United States)

    Douglas, Heather

    2014-06-01

    How should we understand scientific progress? Kuhn famously discussed science as its own internally driven venture, structured by paradigms. He also famously had a problem describing progress in science, as problem-solving ability failed to provide a clear rubric across paradigm change--paradigm changes tossed out problems as well as solving them. I argue here that much of Kuhn's inability to articulate a clear view of scientific progress stems from his focus on pure science and a neglect of applied science. I trace the history of the distinction between pure and applied science, showing how the distinction came about, the rhetorical uses to which the distinction has been put, and how pure science came to be both more valued by scientists and philosophers. I argue that the distinction between pure and applied science does not stand up to philosophical scrutiny, and that once we relinquish it, we can provide Kuhn with a clear sense of scientific progress. It is not one, though, that will ultimately prove acceptable. For that, societal evaluations of scientific work are needed.

  4. Binomial Squares in Pure Cubic Number Fields

    CERN Document Server

    Lemmermeyer, Franz

    2011-01-01

    Let K = Q(\\omega) with \\omega^3 = m be a pure cubic number field. We show that the elements\\alpha \\in K^\\times whose squares have the form a - \\omega form a group isomorphic to the group of rational points on the elliptic curve E_m: y^2= x^3 - m.

  5. Nigeria Journal of Pure and Applied Physics

    African Journals Online (AJOL)

    Nigeria Journal of Pure and Applied Physics (NJPAP) is a journal dedicated to the ... Variations of surface temparature with solar activity at two stations in the tropics ... Activation energy of psuedobinary alloy of Al-Bi-Se mixed systems · EMAIL ...

  6. Evolution of Pure States into Mixed States

    CERN Document Server

    Liu, J

    1993-01-01

    In the formulation of Banks, Peskin and Susskind, we show that one can construct evolution equations for the quantum mechanical density matrix $\\rho$ with operators which do not commute with hamiltonian which evolve pure states into mixed states, preserve the normalization and positivity of $\\rho$ and conserve energy. Furthermore, it seems to be different from a quantum mechanical system with random sources.

  7. Pure Gravitational Back-Reaction Observables

    CERN Document Server

    Tsamis, N C

    2013-01-01

    After discussing the various issues regarding and requirements on pure quantum gravitational observables in homogeneous-isotropic conditions, we construct a composite operator observable satisfying most of them. We also expand it to first order in the loop counting parameter and suggest it as a physical quantifier of gravitational back-reaction in an initially inflating cosmology.

  8. A fatal case of pure metaphyseal chondroblastoma.

    Science.gov (United States)

    Binesh, Fariba; Moghadam, Reza Nafisi; Abrisham, Jalil

    2013-08-23

    The chondroblastoma (CB) is a rare cartilaginous tumour; it represents less than 1% of all bone tumours. It is mostly localised at the level of the epiphysis of long bones. We report a fatal case of pure metaphyseal CB of the tibia in a 9-year-old boy whose pulmonary metastases developed soon after operative therapy of the primary tumour.

  9. MRI of autosomal dominant pure spastic paraplegia

    DEFF Research Database (Denmark)

    Krabbe, K; Nielsen, J E; Fallentin, E

    1997-01-01

    We examined 16 patients with autosomal dominant pure spastic paraplegia (HSP) and 15 normal controls matched for age and sex using MRI of the brain and spinal cord. Images were assessed qualitatively by two independent radiologists, blinded to the clinical diagnosis. Areas of the brain and corpus...

  10. Exploring the simplest purely baryonic decay processes

    CERN Document Server

    Geng, C Q; Rodrigues, Eduardo

    2016-01-01

    We propose to search for purely baryonic decay processes at the LHCb experiment. In particular, we concentrate on the decay $\\Lambda_b^0\\to p\\bar pn$, which is the simplest purely baryonic decay mode, with solely spin-1/2 baryons involved. We predict its decay branching ratio to be ${\\cal B}(\\Lambda_b^0\\to p\\bar pn)=(2.0^{+0.3}_{-0.2})\\times 10^{-6}$, which is sufficiently large to make the decay mode accessible to LHCb. Though not considered in general, purely baryonic decays could shed light on the puzzle of the baryon number asymmetry in the universe by means of a better understanding of the baryonic nature of our matter world. As such, they constitute a yet unexplored class of decay processes worth investigating. Our study can be extended to the purely baryonic decays of $\\Lambda_b^0\\to p\\bar p \\Lambda$, $\\Lambda_b^0\\to \\Lambda \\bar p\\Lambda$ and $\\Lambda_b^0\\to \\Lambda\\bar \\Lambda\\Lambda$, as well as other similar anti-triplet $b$-baryon decays, such as $\\Xi_b^{0,-}$.

  11. Effects of Ultrasonic Treatment on Residue Properties

    Institute of Scientific and Technical Information of China (English)

    Sun Yudong; Zhang Qiang; Shi Honghong; Wang Xue; Liu Bo

    2013-01-01

    The changes in properties and structural parameters of four vacuum residue samples before and after ultrasonic treatment were analyzed. Ultrasonic treatment could increase the carbon residue value, decrease the average molecular weight and viscosity, which can barely inlfuence the density of vacuum residue. Meanwhile the constitution of residue can be varied including the decrease in the content of saturates, aromatics and asphaltenes, while the increase in the content of resins can lead to an increase in the total content of asphaltenes and resins. Among the four kinds of residue samples, there is a common trend that the more the content of asphaltenes in feedstock is, the more the increase in the content of resins, the more signiifcant decrease in the aromatic content and the less decrease in the saturates content after ultrasonic treatment of residue would be. Changes in the structure and content of asphaltenes caused by ultrasonic treatment have a signiifcant impact on the changes in residue properties. Ultrasonic treatment has changed the structural parameters of residue such as decrease in the total carbon number of average molecule (CTotal), the total number of rings (RT), the aromatic carbon number (CA),the aromatic rings number (RA) and the naphthenic rings number (RN) , and increase of characterization factor (KH). The study has indicated that ultrasonic treatment of vacuum residue can change the average structure of residue, and the changes in the content and structure of asphaltenes are the main cause leading to property changes. The results of residue hydrotreat-ing revealed that coke yield decreased, whereas the gas and light oil yield and conversion increased after ultrasonic treat-ment of vacuum residue.

  12. Wetting Behavior in Ultrasonic Vibration-Assisted Brazing of Aluminum to Graphite Using Sn-Ag-Ti Active Solder

    Science.gov (United States)

    Yu, Wei-Yuan; Liu, Sen-Hui; Liu, Xin-Ya; Shao, Jia-Lin; Liu, Min-Pen

    2015-03-01

    In this study, Sn-Ag-Ti ternary alloy has been used as the active solder to braze pure aluminum and graphite in atmospheric conditions using ultrasonic vibration as an aid. The authors studied the formation, composition and decomposition temperature of the surface oxides of the active solder under atmospheric conditions. In addition, the wettability of Sn-5Ag-8Ti active solder on the surface of pure aluminum and graphite has also been studied. The results showed that the major components presented in the surface oxides formed on the Sn-5Ag-8Ti active solder under ambient conditions are TiO, TiO2, Ti2O3, Ti3O5 and SnO2. Apart from AgO and Ag2O2, which can be decomposed at the brazing temperature (773 K), other oxides will not be decomposed. The oxide layer comprises composite oxides and it forms a compact layer with a certain thickness to enclose the melted solder, which will prevent the liquid solder from wetting the base metals at the brazing temperature. After ultrasonic vibration, the oxide layer was destroyed and the liquid solder was able to wet and spread out around the base materials. Furthermore, better wettability of the active solder was observed on the surface of graphite and pure aluminum at the brazing temperature of 773-823 K using ultrasonic waves. The ultrasonic wave acts as the dominant driving factor which promotes the wetting and spreading of the liquid solder on the surface of graphite and aluminum to achieve a stable and reliable brazed joint.

  13. Postcultural Communication?

    DEFF Research Database (Denmark)

    Jensen, Iben

    2015-01-01

    When we as scholars use the concept of intercultural communication in its classic definition, as communication between people with different cultural backgrounds, we perpetuate the notion that national differences influence communication more than other differences; in doing so, ethnic minorities...

  14. Quantitative ultrasonic phased array imaging

    Science.gov (United States)

    Engle, Brady J.; Schmerr, Lester W., Jr.; Sedov, Alexander

    2014-02-01

    When imaging with ultrasonic phased arrays, what do we actually image? What quantitative information is contained in the image? Ad-hoc delay-and-sum methods such as the synthetic aperture focusing technique (SAFT) and the total focusing method (TFM) fail to answer these questions. We have shown that a new quantitative approach allows the formation of flaw images by explicitly inverting the Thompson-Gray measurement model. To examine the above questions, we have set up a software simulation test bed that considers a 2-D scalar scattering problem of a cylindrical inclusion with the method of separation of variables. It is shown that in SAFT types of imaging the only part of the flaw properly imaged is the front surface specular response of the flaw. Other responses (back surface reflections, creeping waves, etc.) are improperly imaged and form artifacts in the image. In the case of TFM-like imaging the quantity being properly imaged is an angular integration of the front surface reflectivity. The other, improperly imaged responses are also averaged, leading to a reduction in some of the artifacts present. Our results have strong implications for flaw sizing and flaw characterization with delay-and-sum images.

  15. Applied orthogonal design for filtrating conditions of ultrasonic ...

    African Journals Online (AJOL)

    user

    2011-03-28

    Mar 28, 2011 ... ultrasonic-assisted extraction from plant-chicory. Yuyan Liu1 ...... nutritional value and biological activities of the acetone, methanol and water extracts of .... of mass transfer in supercritical CO2 extraction processes. Ultrasonics ...

  16. Effect of ultrasonic specific energy on waste activated sludge ...

    African Journals Online (AJOL)

    USER

    2010-03-22

    Mar 22, 2010 ... Full Length Research Paper. Effect of ultrasonic ... Key word: Waste activated sludge (WAS), ultrasonic, solubilization, disintegration degree, enzyme activity. ... burning and land filling, have been carried out for the disposal of ...

  17. Study on electrical impedance matching for broadband ultrasonic transducer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Geon Woo [University of Science and Technology, Daejeon (Korea, Republic of); Kim, Ki Bok [Korea Research Institute of Standards and Science, Center for Safety Measurement, Daejeon (Korea, Republic of); Baek, Kwang Sae [Elache Co., Busan (Korea, Republic of)

    2017-02-15

    Ultrasonic transducers with high resolution and resonant frequency are required to detect small defects (less than hundreds of μm) by ultrasonic testing. The resonance frequency and resolution of an ultrasonic transducer are closely related to the thickness of piezo-electric materials, backing materials, and the electric impedance matching technique. Among these factors, electrical impedance matching plays an important role because it can reduce the loss and reflection of ultrasonic energy differences in electrical impedance between an ultrasonic transducer and an ultrasonic defects detecting system. An LC matching circuit is the most frequently used electric matching method. It is necessary for the electrical impedance of an ultrasonic transducer to correspond to approximately 50 Ω to compensate the difference in electrical impedance between both connections. In this study, a 15 MHz immersion ultrasonic transducer was fabricated and an LC electrical impedance circuit was applied to that for having broad-band frequency characteristic.

  18. Comparison of hydrogen storage properties of pure Mg and milled pure Mg

    Indian Academy of Sciences (India)

    Myoung Youp Song; Young Jun Kwak; Seong Ho Lee; Hye Ryoung Park

    2014-06-01

    Hydrogen storage properties of pure Mg were studied at 593 K under 12 bar H2. In order to increase the hydriding and dehydriding rates, pure Mg was ground under hydrogen atmosphere (reactive mechanical grinding, RMG) and its hydrogen storage properties were subsequently investigated. Pure Mg absorbed hydrogen very slowly. At the number of cycles () of 1, pure Mg absorbed 0.05 wt% H for 5 min, 0.08 wt% H for 10 min and 0.29 wt% H for 60 min at 593 K under 12 bar H2. Activation was completed at the fifth cycle. At = 6, pure Mg absorbed 1.76 wt% H for 5 min, 2.17 wt% H for 10 min and 3.40 wt% H for 60 min. The activation of pure Mg after RMG was completed at the sixth cycle. At = 7, pure Mg after RMG absorbed 2.57 wt% H for 5 min, 3.21 wt% H for 10 min and 4.15 wt% H for 60 min.

  19. Strategizing Communication

    DEFF Research Database (Denmark)

    Gulbrandsen, Ib Tunby; Just, Sine Nørholm

    not determine the success of strategic communication. Rather, contextual factors such as competition, technological developments, global cultural trends and local traditions as well as employees’ skills and attitudes will determine the organization’s communicative success. This holds true regardless...... and less on the plan to communicate. Against the backdrop of the comprehensive changes to communication in and about organizations brought about by the rise of digital communication technologies and related contextual developments, Strategizing Communication provides better and more up to date tools...

  20. Efficacy of commercially available ultrasonic pest repellent devices to affect behavior of bed bugs (Hemiptera: Cimicidae).

    Science.gov (United States)

    Yturralde, K M; Hofstetter, R W

    2012-12-01

    Little is known about the potential for acoustic communication in bed bugs, Cimex lectularius L. (Hemiptera: Cimicidae), or the use of sound as cues in host location, although many hemipterans are known to communicate with sound. Most behavioral research has focused on bed bug pheromones that are used in aggregation and as alarm signals. We investigated the influence of sound as a deterrent and as an attractant, either of which could ultimately be used to monitor and control bed bugs. Female bed bugs were tested in two-choice tests with four different commercially available ultrasonic repellent devices. We found that female bed bugs were equally likely to occur in arenas with or without sound produced by ultrasonic devices. These devices did not repel or attract bed bugs during choice trials. However, more bed bugs preferred the middle corridor between the test (sound) and control (no sound) arenas when the sound devices were played. Bed bugs were also more likely to exit the middle corridor during control trials compared with treatment trials with ultrasonic devices. Our results confirm that commercial devices producing ultrasound are not a promising tool for repelling bed bugs.

  1. Laser ultrasonic diagnostics of residual stress.

    Science.gov (United States)

    Karabutov, Alexander; Devichensky, Anton; Ivochkin, Alexander; Lyamshev, Michael; Pelivanov, Ivan; Rohadgi, Upendra; Solomatin, Vladimir; Subudhi, Manomohan

    2008-11-01

    Ultrasonic NDE is one of the most promising methods for non-destructive diagnostics of residual stresses. However the relative change of sound velocity, which is directly proportional to applied stress, is extremely small. An initial stress of 100 MPa produces the result of deltaV/V approximately 10(-4). Therefore measurements must be performed with high precision. The required accuracy can be achieved with laser-exited ultrasonic transients. Radiation from a Nd-YAG laser (pulse duration 7 ns, pulse energy 100 microJ) was absorbed by the surface of the sample. The exited ultrasonic transients resembled the form of laser pulses. A specially designed optoacoustic transducer was used both for the excitation and detecting of the ultrasonic pulses. The wide frequency band of the piezodetector made it possible to achieve the time-of-flight measurements with an accuracy of about 0.5 ns. This technique was used for measuring of plane residual stress in welds and for in-depth testing of subsurface residual stresses in metals. Plane stress distribution for welded metallic plates of different thicknesses (2-8 mm) and the subsurface stress distribution for titanium and nickel alloys were obtained. The results of conventional testing are in good agreement with the laser ultrasonic method.

  2. Signal Separation in Ultrasonic Non-Destructive Testing

    OpenAIRE

    V. Matz; M. Kreidl; R. Šmíd

    2007-01-01

    In ultrasonic non-destructive testing the signals characterizing the material structure are commonly evaluated. The sensitivity and resolution of ultrasonic systems is limited by the backscattering and electronic noise level commonly contained in the acquired ultrasonic signals. For this reason, it is very important to use appropriate advanced signal processing methods for noise reduction and signal separation. This paper compares algorithms used for efficient noise reduction in ultrasonic si...

  3. Ultrasonic measurement models for imaging with phased arrays

    Science.gov (United States)

    Schmerr, Lester W., Jr.; Engle, Brady J.; Sedov, Alexander; Li, Xiongbing

    2014-02-01

    Ultrasonic imaging measurement models (IMMs) are developed that generate images of flaws by inversion of ultrasonic measurement models. These IMMs are generalizations of the synthetic aperture focusing technique (SAFT) and the total focusing method (TFM). A special case when the flaw is small is shown to generalize physical optics far field inverse scattering (POFFIS) images. The ultrasonic IMMs provide a rational basis for generating and understanding the ultrasonic images produced by delay-and-sum imaging methods.

  4. Ultrasonic Dental Scaler Performance Assessment with an Innovative Cavitometer

    OpenAIRE

    Antonio H.A. Pereira; Camila Tirapelli; Lucimar A. Rodolpho

    2010-01-01

    Problem statement: There is no specific instrument to test ultrasonic dental scalers used in dentistry. Approach: The aim of this research was to develop and test an innovative cavitometer for quantitative and automatic performance assessments of Ultrasonic Dental Scalers (UDS) through the acoustic emission produced by cavitation induced by the tip of the UDS ultrasonic transducer when immersed in aqueous solution. Firstly, an optimized acoustic emission sensor specifically for UDS ultrasonic...

  5. Separation of metal ions in nitrate solution by ultrasonic atomization

    Science.gov (United States)

    Sato, Masanori; Ikeno, Masayuki; Fujii, Toshitaka

    2004-11-01

    In the ultrasonic atomization of metal nitrate solutions, the molar ratio of metal ions is changed between solution and mist. Small molar metal ions tend to be transferred to mist by ultrasonic wave acceleration, while large molar ions tend to remain in solution. As a result, metal ions can be separated by ultrasonic atomization. We show experimental data and propose a conceptual mechanism for the ultrasonic separation of metal ions.

  6. Ultrasonic Cleaning of Nuclear Steam Generator by Micro Bubble

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Woo Tae [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of); Kim, Sang Tae; Yoon, Sang Jung [Sae-An Engineering Co., Seoul (Korea, Republic of)

    2012-05-15

    In this paper, we present ultrasonic cleaning technology for a nuclear steam generator using micro bubble. We could extend the boundary of ultrasonic cleaning by using micro bubbles in water. Ultrasonic energy measured was increased about 5 times after the generation of micro bubbles in water. Furthermore, ultrasound energy was measured to be strong enough to create cavitation even though the ultrasound sensor was about 2 meters away from the ultrasonic transducer

  7. Effect of the cortex on ultrasonic backscatter measurements of cancellous bone

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmeister, Brent K; Holt, Andrew P [Department of Physics, Rhodes College, Memphis, TN (United States); Kaste, Sue C, E-mail: hoffmeister@rhodes.edu [Department of Diagnostic Imaging, St Jude Children' s Research Hospital, Memphis, TN (United States)

    2011-10-07

    Ultrasonic backscatter techniques offer a promising new approach for detecting changes in bone caused by osteoporosis. However, several challenges impede clinical implementation of backscatter techniques. This study examines how the dense outer surface of bone (the cortex) affects backscatter measurements of interior regions of porous (cancellous) bone tissue. Fifty-two specimens of bone were prepared from 13 human femoral heads so that the same region of cancellous bone could be ultrasonically interrogated through the cortex or along directions that avoided the cortex. Backscatter signals were analyzed over a frequency range of 0.8-3.0 MHz to determine two ultrasonic parameters: apparent integrated backscatter (AIB) and frequency slope of apparent backscatter (FSAB). The term 'apparent' means that the parameters are sensitive to the frequency-dependent effects of diffraction and attenuation. Significant (p < 0.001) changes in AIB and FSAB indicated that measurements through the cortex decreased the apparent backscattered power and increased the frequency dependence of the power. However, the cortex did not affect the correlation of AIB and FSAB with the x-ray bone mineral density of the specimens. This suggests that results from many previous in vitro backscatter studies of specimens of purely cancellous bone may be extrapolated with greater confidence to in vivo conditions.

  8. Low Energy Gamma Radiation Induced Effects on Ultrasonic Velocity and Acoustic Parameters in Polyvinylidene Fluoride Solution

    Directory of Open Access Journals (Sweden)

    S. S. Kulkarni

    2016-01-01

    Full Text Available The modification of polyvinylidene fluoride (PVDF polymer properties with irradiation is of interest as it possesses unique piezo-, pyro-, and ferroelectric properties. In this paper, we report the results of acoustic parameters of irradiated PVDF mixed with dimethylacetamide (DMAC solution with low energy γ-source (Cs-137. The polymer solution covered with mica film assures only γ-ray passage and the duration was increased from 18 to 50 hours to achieve the higher dose rate. The dose rate was estimated using the strength of the radioactive source and the duration of the exposure. The ultrasonic velocity (v, density (ρ, and viscosity (η of 0.2 wt% and 0.5 wt% PVDF dissolved in pure DMAC solution, irradiated with different dose rate were measured using ultrasonic interferometer (Mittal make, Pyknometer, and Oswald’s viscometer, respectively. It is observed that the values of v, ρ, and η change with dose rate. The acoustic parameters such as adiabatic compressibility (β, intermolecular free path length (Lf, acoustic impedance (Z, relative association (RA, ultrasonic attenuation (α/f2, and relaxation time (τ are calculated using the experimental data. These results are interpreted in terms of the solute-solvent interaction in a polymer solution and scissoring chain damage.

  9. The influence of the ultrasonic intensity on the cleaning efficacy of passive ultrasonic irrigation.

    Science.gov (United States)

    Jiang, Lei-Meng; Verhaagen, Bram; Versluis, Michel; Langedijk, Jelmer; Wesselink, Paul; van der Sluis, Lucas W M

    2011-05-01

    It is not clear whether increasing the ultrasonic intensity would enhance the cleaning efficacy of passive ultrasonic irrigation (PUI) inside a root canal. The aim of this study was to evaluate the effect of the ultrasonic intensity on PUI to remove dentin debris and whether there is any lateral effect beyond the ultrasonic tip. Each of 15 in vitro root canal models with four standard depressions in the apical part of one canal wall were filled with dentin debris and received PUI repeatedly. The most apical depression was localized apically from the ultrasonic tip. The highest intensity was applied in group 1, the lowest intensity was applied in group 3, and syringe irrigation was performed in group 4 as a control. Before and after irrigation, images of the canal wall with depressions were taken and compared. The removal of dentin debris in the depression was categorized as clean or not clean. The data were analyzed by means of the chi-square test. The oscillation amplitude of the ultrasonic file at each intensity was recorded in vitro using time-resolved high-speed imaging. Group 1 (highest intensity) exhibited significantly better cleaning than all the other groups (P ultrasonic intensity resulted in a higher amplitude of the oscillating file and, consequently, enhanced the cleaning efficacy of PUI. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  10. Ultrasonic echo signal fetures of dissimilar material bonding joints

    Institute of Scientific and Technical Information of China (English)

    GANG Tie(刚铁); Yasuo TAKAHASHI

    2004-01-01

    An ultrasonic evaluation method of echo feature of diffusion bond joint between two dissimilar materials is presented. The echo signal was acquired by an automatic ultrasonic C-scan test system. It is found that the intensity of echo and its phase can be used to evaluate the joint quality, and interface products of dissimilar materials bonding can be evaluated by ultrasonic method.

  11. 21 CFR 892.1560 - Ultrasonic pulsed echo imaging system.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultrasonic pulsed echo imaging system. 892.1560... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1560 Ultrasonic pulsed echo imaging system. (a) Identification. An ultrasonic pulsed echo imaging system is a device intended to project...

  12. 21 CFR 884.2960 - Obstetric ultrasonic transducer and accessories.

    Science.gov (United States)

    2010-04-01

    ... energy from, the body in conjunction with an obstetric monitor or imager. The device converts electrical signals into ultrasonic energy, and vice versa, by means of an assembly distinct from an ultrasonic... type of device does not include devices used to generate the ultrasonic frequency electrical...

  13. Communications article

    KAUST Repository

    Fariborzi, Hossein

    2017-07-20

    Seamless, covert communications using a communications system integrated or incorporated within an article of clothing is described. In one embodiment, the communications system is integrated or incorporated into a shoe insole and includes a haptic feedback mechanism, a communications module, a flexible pressure sensor, and a battery. The communications module includes a wireless communications module for wireless communications, a wired interface for wired communications, a microcontroller, and a battery charge controller. The flexible pressure sensor can be actuated by an individual\\'s toe, for example, and communication between two communications nodes can be achieved using coded signals sent by individuals using a combination of long and short presses on the pressure sensor. In response to the presses, wireless communications modules can transmit and receive coded signals based on the presses.

  14. Black Hole Attractors and Pure Spinors

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Jonathan P.; Maloney, Alexander; Tomasiello, Alessandro

    2006-02-21

    We construct black hole attractor solutions for a wide class of N = 2 compactifications. The analysis is carried out in ten dimensions and makes crucial use of pure spinor techniques. This formalism can accommodate non-Kaehler manifolds as well as compactifications with flux, in addition to the usual Calabi-Yau case. At the attractor point, the charges fix the moduli according to {Sigma}f{sub k} = Im(C{Phi}), where {Phi} is a pure spinor of odd (even) chirality in IIB (A). For IIB on a Calabi-Yau, {Phi} = {Omega} and the equation reduces to the usual one. Methods in generalized complex geometry can be used to study solutions to the attractor equation.

  15. New Perspective of High-Pure Silicon

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@The discovery in the middle of 1950s of the semi-con ducting properties of crystalline silicon has led to the impetu ous development of electric power facilities, the sun-power industry, and particularly, the microelectronic industry. The increasing demand for the high-pure silicon requires the production of synthetic crystals. The raw material for the syn thetic crystals, the so-called technical, or metallurgical silicon, is obtained from quartzite and quartz of superior quality by means of carbon-thermal reduction of silicon using an electric arc discharge. The complexity of the technological process, high cost of the related facilities, worsening environmental pollution, and narrow-mindedness of a raw material company are attributed to the rise in price of the final product-silicon plates, resulting in the fall in the production of high-pure silicon, normally used in sun storage batteries.

  16. Performance of broiler fed pure glycerine

    Directory of Open Access Journals (Sweden)

    Dássia Daiane Oliveira

    2014-02-01

    Full Text Available Two experiments evaluated the pure glycerin in broiler chicken diets. Experiment 1 was a metabolism test using total feces sampling method with 96 male chickens aging from 17 to 25 d when animals were fed on two treatments: diet1 = no glycerin and diet2 = 60g/kg of glycerin. The apparent metabolized energy measured 4015 kcal/kg and the apparent metabolized corrected for nitrogen balance was 3911 kcal/kg. Experiment 2 evaluated weight gains, feed intake and feed conversion in 480 chicks at 6, 20 and 34 d old fed on diets with 0, 40, 80 and 120 g/kg of glycerin. The results indicate that pure glycerin in chicken diets, as a source of energy must take into consideration the age of the animals and it may be added up to 120 g/kg, from 20 to 41 d of age.

  17. Pure and doped boron nitride nanotubes

    Directory of Open Access Journals (Sweden)

    M. Terrones

    2007-05-01

    Full Text Available More than ten years ago, it was suggested theoretically that boron nitride (BN nanotubes could be produced. Soon after, various reports on their synthesis appeared and a new area of nanotube science was born. This review aims to cover the latest advances related to the synthesis of BN nanotubes. We show that these tubes can now be produced in larger amounts and, in particular, that the chemistry of BN tubes appears to be very important to the production of reinforced composites with insulating characteristics. From the theoretical standpoint, we also show that (BN-C heteronanotubes could have important implications for nanoelectronics. We believe that BN nanotubes (pure and doped could be used in the fabrication of novel devices in which pure carbon nanotubes do not perform very efficiently.

  18. The pure relationship and below replacement fertility

    Directory of Open Access Journals (Sweden)

    David R. Hall

    2003-12-01

    interest from demographers. Despite the fact that researchers have extensively modeled recent demographic changes such as skyrocketing divorce rates, rising common-law union formation, delayed childbearing, and the decline to belowreplacement fertility levels, our understanding of the causes of these trends, and the possible connections between them remains theoretically fragmented and incomplete. The goal of this paper is to advance our understanding in this area by exploring the insights on modern family formation of prominent sociologist Anthony Giddens. Specifically, this study examines whether Giddens’ “pure relationship” concept can shed light on the trend toward very low fertility. The results of this inquiry suggest that couples in both marriages and common-law unions who conform to key aspects of Giddens pure relationship are more likely to have uncertain or below-replacement fertility intentions, and less likely to embrace above-replacement fertility goals.

  19. Compact objects in pure Lovelock theory

    CERN Document Server

    Dadhich, Naresh; Chilambwe, Brian

    2016-01-01

    For static fluid interiors of compact objects in pure Lovelock gravity (involving ony one $N$th order term in the equation) we establish similarity in solutions for the critical odd and even $d=2N+1, 2N+2$ dimensions. It turns out that in critical odd $d=2N+1$ dimensions, there can exist no bound distribution with a finite radius, while in critical even $d=2N+2$ dimensions, all solutions have similar behavior. For exhibition of similarity we would compare star solutions for $N =1, 2$ in $d=4$ Einstein and $d=6$ in Gauss-Bonnet theory respectively. We also obtain the pure Lovelock analogue of the Finch-Skea model.

  20. Effective pure states for bulk quantum computation

    Energy Technology Data Exchange (ETDEWEB)

    Knill, E.; Chuang, I.; Laflamme, R.

    1997-11-01

    In bulk quantum computation one can manipulate a large number of indistinguishable quantum computers by parallel unitary operations and measure expectation values of certain observables with limited sensitivity. The initial state of each computer in the ensemble is known but not pure. Methods for obtaining effective pure input states by a series of manipulations have been described by Gershenfeld and Chuang (logical labeling) and Corey et al. (spatial averaging) for the case of quantum computation with nuclear magnetic resonance. We give a different technique called temporal averaging. This method is based on classical randomization, requires no ancilla qubits and can be implemented in nuclear magnetic resonance without using gradient fields. We introduce several temporal averaging algorithms suitable for both high temperature and low temperature bulk quantum computing and analyze the signal to noise behavior of each.

  1. Development of Soybean Highly Pure Powdered Lecithin

    Institute of Scientific and Technical Information of China (English)

    Li Guihua; Gu Keren; Liang Shaohua

    2002-01-01

    This project makes use ofCondensed Soybean Phospholipids (CSP) toproduce highly pure powdered soybean lecithin.In the production technology, the first step is tode-oil by continuous y delivered mater al, higheffective mixing CSP with acetone and circularextraction. The second step is to centrifugallyseparate the lecithin miscellaneous liquid intomiscellaneous oil and solid-state lecithin withacetone. Then the mixing oil can be separatedinto crude oil and acetone by vaporization andcondensation. If the acetone contains too muchwater, it should be rectified for use circularly.Solid state lecithin with acetone can be madeinto highly pure powdered soybean lecithin(acetone insoluble matter >95% ) under thefollowing conditions: vacuum 750mmHg,temperature 60℃, time 20 minutes. Theproduction not only reaches the domestic andoversea quality index, but also has favorablehydrophilic property, which makes it becomenatural food additive and sanitarian nurture.

  2. Photoionizaton of Pure and Doped Helium Nanodroplets

    CERN Document Server

    Mudrich, M

    2014-01-01

    Helium nanodroplets, commonly regarded as the "nearly ideal spectroscopic matrix", are being actively studied for more than two decades now. While they mostly serve as cold, weakly perturbing and transparent medium for high-resolution spectroscopy of embedded molecules, their intrinsic quantum properties such as microscopic superfluidity still are subject-matter of current research. This article reviews recent work on pure and doped He nanodroplets using PI spectroscopy, an approach which has greatly advanced in the past years. While the notion of the ideal spectroscopic matrix mostly no longer holds in this context, photoionization techniques provide detailed insights into the photo-physical properties of pure and doped He nanodroplets and their relaxation dynamics following electronic excitation. Exploiting nowadays available high laser fields, even highly ionized states of matter on the nanoscale can be formed. Our particular focus lies on recent experimental progress including fs time-resolved spectroscop...

  3. How Pure Components Control Polymer Blend Miscibility

    Science.gov (United States)

    White, Ronald; Lipson, Jane; Higgins, Julia

    2012-02-01

    We present insight into some intriguing relationships revealed by our recent studies of polymer mixture miscibility. Applying our simple lattice-based equation of state, we discuss some of the patterns observed over a sample of experimental blends. We focus on the question of how much key information can one determine from a knowledge of just the pure components only, and further, on the role of separate enthalpic and entropic contributions to the miscibility behavior. One interesting correlation connects the value of the difference in pure component energetic parameters with that of the mixed segment interactions, suggesting new possibilities for predictive modeling. We also show how in some cases these two parameter groupings act as separate controls determining the entropy and enthalpy of mixing. Also discussed are the different patterns exhibited for UCST-type and LCST-type blends, these being revealed in some cases by simple examination of the underlying microscopic parameters.

  4. Pure Sensory Stroke due to Lenticulocapsular Hemorrhage

    Institute of Scientific and Technical Information of China (English)

    杨益阶; 王国瑾; 潘松青

    2003-01-01

    @@ Pure sensory stroke (PSS) caused by lenticulo-capsular hemorrhage is rare. In this article, we re-ported 4 patients with PSS due to lenticulocapsularhemorrhage, including 3 men and 1 woman (mean age,58 years; range, 54 to 65 years), whose lesions couldbe identified by head computed tomographic (CT)scan and clinical findings correlated with the radio-logical lesions. All patients except 1 had hyperten-sion.

  5. Acquired pure red cell aplasia in children

    Directory of Open Access Journals (Sweden)

    Sujata R Dafale

    2012-01-01

    Full Text Available Acquired Pure Red Cell Aplasia (PRCA is a rare occurrence in children.This is a case of an eight year old girl child who developed acquired PRCA secondary to long term intake of sodium Valproate. This case is reported to review the causes of PRCA in children and to reconsider the use of drugs of longer duration in children and adults.

  6. Pure waterjet drilling of articular bone

    OpenAIRE

    Biskup, Christian; Dunnen, Steven den; Kraaij, Gert; Kerkhoffs, Gino M. M. J.; Tuijthof, Gabrielle J. M.

    2015-01-01

    The clinical application of waterjet technology for machining tough human tissues, such as articular bone, has advantages, as it produces clean sharp cuts without tissue heating. Additionally, water supply is possible via flexible tubing, which enables minimally invasive surgical access. This pilot study investigates whether drilling bony tissue with pure waterjets is feasible. Water pressures between 20 and 120 MPa with an orifice of 0.6 mm were used to create waterjets to drill blind boring...

  7. Les Problemes de l'alexie pure (Problems of Pure Alexia)

    Science.gov (United States)

    Kremin, Helgard

    1976-01-01

    This article reviews studies done on alexia and describes experiments designed to distinguish qualitatively between pure alexia (marked by the absence of oral and written problems) and other forms of alexia. (Text is in French.) (CLK)

  8. Ultrasonic Welding of Wires and Cables

    Science.gov (United States)

    Heinz, Stefan; Wagner, Guntram; Eifler, Dietmar

    2012-03-01

    In the automobile industry, ultrasonic metal welding is an established method. At the Institute of Materials Science and Engineering (WKK) at the University of Kaiserslautern, Germany, systematic investigations of the weldability of Al-wires and flat flexible copper cables were carried out. In the case of Al-wires, joints with cross-sectional area of up to 80 mm2 and tensile shear load of about 3500 N were finally realized. Furthermore, methods to reduce unintentional adherence between the sonotrode coupling face and the Al-wires were developed. To realize FFC joints, ultrasonic spot welding systems and ultrasonic torsion welding systems were used. A central purpose of these investigations is the development of a system to enable welding through the insulation of the FFC without weakening the base material.

  9. Process monitoring using ultrasonic sensor systems.

    Science.gov (United States)

    Henning, Bernd; Rautenberg, Jens

    2006-12-22

    Continuous in-line measurement of substance concentration in liquid mixtures is valuable in improving industrial processes in terms of material properties, energy efficiency and process safety. Ultrasonic sensor systems meet the practical requirements of a chemical sensor quite well. Currently ultrasonic sensor systems are widely used as acoustic chemical sensors to measure concentration of selected substances or to monitor the course of polymerisation, crystallisation or fermentation processes. Useable acoustic properties for the characterisation of liquid mixtures are sound velocity, sound absorption and acoustic impedance. This contribution will give a short overview of the state of the art and several trends for the use of ultrasonic sensor systems in process applications. Novel investigations show the very promising possibility to analyse liquid multi-phase mixtures like suspensions, emulsions and dispersions.

  10. Monitoring Thermal Coagulation with Ultrasonic Textures

    Institute of Scientific and Technical Information of China (English)

    YANG Wei; ZHANG Su; CHEN Ya-zhu; CHEN Lei; HU Bing; MA Wei-yin

    2007-01-01

    The feasibility of using B-mode ultrasound image textures and pattern recognition technique to characterize the thermal coagulation in vitro during radiofrequency ablation was investigated.The changes of ultrasonic textures in the different regions of samples varied with the heating time in the in-vitro experiments, which would result in that the coagulated and noncoagulated regions of tissue had different ultrasonic textures.Using support vector machine to extract the ultrasonic texture features and characterize the state of tissue, the size and boundaries of thermal lesions could be detected and measured more exactly than only using the gray scale information of B-mode ultrasound image.The proposed method would be applied to the image-guided radiofrequency ablation (IGRA) procedure for monitoring the thermal coagulation.

  11. Particle size characterization by ultrasonic attenuation spectra

    Institute of Scientific and Technical Information of China (English)

    Mingxu Su; Minghua Xue; Xiaoshu Cai; Zhitao Shang; Feng Xu

    2008-01-01

    This paper contributes to extracting information from signals of broadband ultrasonic attenuation spectrum for effective utilization in particle size characterization. The single particle scattering model and the coupled-phase model are formulated simultaneously, the relationship between particle size distribution and ultrasonic spectrum is established, and a convergence criterion for calculation is quantified. Demonsa'ation inversion by the optimum regularization factor method is carded out to yield typical numerical results for discussion. With the experimental set-up developed by the Institute of Particle and Two-Phase Flow Measurement (IPTFM) at the University of Shanghai for Science and Technology, sand sediment particle size is measured by attenuation spectrum and analyzed using the above inversion algorithm and theoretical models. To validate the proposed ultrasonic spectrum particle sizing method, results are compared with those obtained by microscopy.

  12. Ultrasonic filtration of industrial chemical solutions

    Science.gov (United States)

    Cosma, T.

    1974-01-01

    The practical results obtained as a result of filtering industrial chemical solutions under continuous flow conditions with the aid of an ultrasonic filter are presented. The main part of the assembly consists of an ultrasonic generator with an output power of about 400 W and the filtration assembly, in which there is a magnetostrictive amplifier constructed for 20.5 kHz. In addition to ensuring a continuous flow of filtered solution, ultrasonic filters can be replaced or cleaned at intervals of time that are 8-10 times greater than in the case of mechanical filters. They yield considerably better results as far as the size of the filtered particles is concerned. The parameters on which filtration quality depends are also presented.

  13. Novel Applications of Power Ultrasonic Spray

    Science.gov (United States)

    Quan, Ke-Ming

    Atomization is a process where a liquid is dispersed into droplets in a gas. Ultrasonic atomization was discovered in the 1920s (Loomis and Woods, 1927). Since then, atomization has seen diversified applications in devices such as drug nebulizers, room humidifiers, and air refreshers, as well as in industrial processes such as combustion, prilling, and web coating. In contrast to conventional liquid atomizers, ultrasound atomizers generally handle lower flow rates, and atomization of the liquid is achieved not by pressure, but by the vibration of ultrasonic waves (Morgan, 1993). This latter feature decouples the requirement of orifice geometry and pressure from the flow rate, allowing the flow to be controlled independently. Typically, ultrasonic atomizers excel in accurately processing low flow rates and slurry without clogging issues.

  14. Ultrasonic non invasive techniques for microbiological instrumentation

    Science.gov (United States)

    Elvira, L.; Sierra, C.; Galán, B.; Resa, P.

    2010-01-01

    Non invasive techniques based on ultrasounds have advantageous features to study, characterize and monitor microbiological and enzymatic reactions. These processes may change the sound speed, viscosity or particle distribution size of the medium where they take place, which makes possible their analysis using ultrasonic techniques. In this work, two different systems for the analysis of microbiological liquid media based on ultrasounds are presented. In first place, an industrial application based on an ultrasonic monitoring technique for microbiological growth detection in milk is shown. Such a system may improve the quality control strategies in food production factories, being able to decrease the time required to detect possible contaminations in packed products. Secondly, a study about the growing of the Escherichia coli DH5 α in different conditions is presented. It is shown that the use of ultrasonic non invasive characterization techniques in combination with other conventional measurements like optical density provides complementary information about the metabolism of these bacteria.

  15. Ultrasonically-assisted Polymer Molding: An Evaluation

    Science.gov (United States)

    Moles, Matthew; Roy, Anish; Silberschmidt, Vadim

    Energy reduction in extrusion and injection molding processes can be achieved by the introduction of ultrasonic energy. Polymer flow can be enhanced on application of ultrasonic vibration, which can reduce the thermal and pressure input requirements to produce the same molding; higher productivity may also be achieved. In this paper, a design of an ultrasound-assisted injection mold machine is explored. An extrusion-die design was augmented with a commercial 1.5 kW ultrasonic transducer and sonotrode designed to resonate close to 20 kHz with up to 100 μm vibration amplitude. The design was evaluated with modal and thermal analysis using finite-element analysis software. The use of numerical techniques, including computational fluid dynamics, fluid-structure interaction and coupled Lagrangian-Eulerian method, to predict the effect of ultrasound on polymer flow was considered. A sonotrode design utilizing ceramic to enhance thermal isolation was also explored.

  16. Global empirical potentials from purely rotational measurements

    CERN Document Server

    Dattani, Nikesh S; Sun, Ming; Johnson, Erin R; Roy, Robert J Le; Ziurys, Lucy M

    2014-01-01

    The recent advent of chirped-pulse FTMW technology has created a plethora of pure rotational spectra for molecules for which no vibrational information is known. The growing number of such spectra demands a way to build empirical potential energy surfaces for molecules, without relying on any vibrational measurements. Using ZnO as an example, we demonstrate a powerful technique for efficiently accomplishing this. We first measure eight new ultra-high precision ($\\pm2$ kHz) pure rotational transitions in the $X$-state of ZnO. Combining them with previous high-precision ($\\pm50$ kHz) pure rotational measurements of different transitions in the same system, we have data that spans the bottom 10\\% of the well. Despite not using any vibrational information, our empirical potentials are able to determine the size of the vibrational spacings and bond lengths, with precisions that are more than three and two orders of magnitude greater, respectively, than the most precise empirical values previously known, and the mo...

  17. On constructing purely affine theories with matter

    Science.gov (United States)

    Cervantes-Cota, Jorge L.; Liebscher, D.-E.

    2016-08-01

    We explore ways to obtain the very existence of a space-time metric from an action principle that does not refer to it a priori. Although there are reasons to believe that only a non-local theory can viably achieve this goal, we investigate here local theories that start with Schrödinger's purely affine theory (Schrödinger in Space-time structure. Cambridge UP, Cambridge, 1950), where he gave reasons to set the metric proportional to the Ricci curvature aposteriori. When we leave the context of unified field theory, and we couple the non-gravitational matter using some weak equivalence principle, we can show that the propagation of shock waves does not define a lightcone when the purely affine theory is local and avoids the explicit use of the Ricci tensor in realizing the weak equivalence principle. When the Ricci tensor is substituted for the metric, the equations seem to have only a very limited set of solutions. This backs the conviction that viable purely affine theories have to be non-local.

  18. On constructing purely affine theories with matter

    CERN Document Server

    Cervantes-Cota, Jorge L

    2016-01-01

    We explore ways to obtain the very existence of a space-time metric from an action principle that does not refer to it a priori. Although there are reasons to believe that only a non-local theory can viably achieve this goal, we investigate here local theories that start with Schroedinger's purely affine theory [21], where he gave reasons to set the metric proportional to the Ricci curvature aposteriori. When we leave the context of unified field theory, and we couple the non-gravitational matter using some weak equivalence principle, we can show that the propagation of shock waves does not define a lightcone when the purely affine theory is local and avoids the explicit use of the Ricci tensor in realizing the weak equivalence principle. When the Ricci tensor is substituted for the metric, the equations seem to have only a very limited set of solutions. This backs the conviction that viable purely affine theories have to be non-local.

  19. P.U.R.E. (purposeful, unambiguous, respectful, and effective) Conversations and electronic fetal monitoring: gaining consensus and collaboration.

    Science.gov (United States)

    Veltman, Larry; Larison, Kristine

    2010-11-01

    A revised nomenclature regarding electronic fetal heart rate monitoring was accepted at a National Institute of Child Health and Human Development consensus conference in 2008. At the heart of patient safety are communication strategies that enhance teamwork and collaboration between health care professionals. Communications is a complex 2-way process that involves more than transfer of factual information. P.U.R.E. (purposeful, unambiguous, respectful, and effective) Conversations in Obstetrics is an acronym that helps facilitate this communication process in perinatal care. P.U.R.E. stands for purposeful, unambiguous, respectful, and effective. The P.U.R.E. Conversations approach involves refinement of the mental processes associated with delivering the message, delivery of the message with data, accuracy, and direct requests for action, attention to relationships and behaviors between the communicating parties, and real-time assessment of the effectiveness of the communication. When the new electronic monitoring nomenclature is combined with an effective communication tool, one could expect to see a reduction in communication failures that could lead to adverse perinatal outcomes.

  20. Standard practice for evaluating performance characteristics of ultrasonic Pulse-Echo testing instruments and systems without the use of electronic measurement instruments

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 This practice describes procedures for evaluating the following performance characteristics of ultrasonic pulse-echo examination instruments and systems: Horizontal Limit and Linearity; Vertical Limit and Linearity; Resolution - Entry Surface and Far Surface; Sensitivity and Noise; Accuracy of Calibrated Gain Controls. Evaluation of these characteristics is intended to be used for comparing instruments and systems or, by periodic repetition, for detecting long-term changes in the characteristics of a given instrument or system that may be indicative of impending failure, and which, if beyond certain limits, will require corrective maintenance. Instrument characteristics measured in accordance with this practice are expressed in terms that relate to their potential usefulness for ultrasonic testing. Instrument characteristics expressed in purely electronic terms may be measured as described in E1324. 1.2 Ultrasonic examination systems using pulsed-wave trains and A-scan presentation (rf or video) may be ev...

  1. Ultrasonic precision optical grinding technology

    Science.gov (United States)

    Cahill, Michael J.; Bechtold, Michael J.; Fess, Edward; Wolfs, Frank L.; Bechtold, Rob

    2015-10-01

    As optical geometries become more precise and complex and a wider range of materials are used, the processes used for manufacturing become more critical. As the preparatory stage for polishing, this is especially true for grinding. Slow processing speeds, accelerated tool wear, and poor surface quality are often detriments in manufacturing glass and hard ceramics. The quality of the ground surface greatly influences the polishing process and the resulting finished product. Through extensive research and development, OptiPro Systems has introduced an ultrasonic assisted grinding technology, OptiSonic, which has numerous advantages over traditional grinding processes. OptiSonic utilizes a custom tool holder designed to produce oscillations in line with the rotating spindle. A newly developed software package called IntelliSonic is integral to this platform. IntelliSonic automatically characterizes the tool and continuously optimizes the output frequency for optimal cutting while in contact with the part. This helps maintain a highly consistent process under changing load conditions for a more accurate surface. Utilizing a wide variety of instruments, test have proven to show a reduction in tool wear and increase in surface quality while allowing processing speeds to be increased. OptiSonic has proven to be an enabling technology to overcome the difficulties seen in grinding of glass and hard optical ceramics. OptiSonic has demonstrated numerous advantages over the standard CNC grinding process. Advantages are evident in reduced tool wear, better surface quality, and reduced cycle times due to increased feed rates. These benefits can be seen over numerous applications within the precision optics industry.

  2. The precision of bacterial quantification techniques on different kinds of environmental samples and the effect of ultrasonic treatment.

    Science.gov (United States)

    Böllmann, Jörg; Rathsack, Kristina; Martienssen, Marion

    2016-07-01

    The precision of cell number quantification in environmental samples depends on the complexity of the sample and on the applied technique. We compared fluorescence microscopy after filtration, quantification of gene copies and the cultivation based most probable number technique for their precision. We further analyzed the effect of increasing complexity of the sample material on the precision of the different methods by using pure cultures of Pseudomonas aeruginosa, fresh water samples and sediment slurries with and without ultrasonic treatment for analyses. Microscopy reached the highest precision, which was similar between pure cultures and water samples, but lower for sediment samples due to a higher percentage of cells in clusters and flocks. The PCR based quantification was most precise for pure cultures. Water and sediment samples were similar but less precise, which might be caused by the applied DNA extraction techniques. MPN measurements were equally precise for pure cultures and water samples. For sediment slurries the precision was slightly lower. The applied ultrasonic treatment of the slurries dispersed the cell clusters and flocks, increased the precision of microscopical and MPN measurements and also increased the number of potential colony forming units. However, the culturable cell number decreased by half. For MPN quantification of viable cells in samples with a high proportion of clustered cells we therefore recommend an optimization of ultrasonic treatment and a confirmation by microscopy and cultivation to reach highest possible dispersion of the cells with a minimum of inactivation. As a result of these observations we suggest a correction factor for MPN measurements to consider the effect of sonication on complex samples. The results are most likely applicable to other complex samples such as soil or biofilms.

  3. High-frequency, silicon-based ultrasonic nozzles using multiple Fourier horns.

    Science.gov (United States)

    Tsai, Shirley C; Song, Yu L; Tseng, Terry K; Chou, Yuan F; Chen, Wei J; Tsai, Chen S

    2004-03-01

    This paper presents the design, simulation, and characterization of microfabricated 0.5 MHz, silicon-based, ultrasonic nozzles. Each nozzle is made of a piezoelectric drive section and a silicon resonator consisting of multiple Fourier horns, each with half wavelength design and twice amplitude magnification. Results of finite element three-dimensional (3-D) simulation using a commercial program predicted existence of one resonant frequency of pure longitudinal vibration. Both impedance analysis and measurement of longitudinal vibration confirmed the simulation results with one pure longitudinal vibration mode at the resonant frequency in excellent agreement with the design value. Furthermore, at the resonant frequency, the measured longitudinal vibration amplitude at the nozzle tip increases as the number of Fourier horns (n) increases in good agreement with the theoretical values of 2(n). Using this design, very high vibration amplitude gain at the nozzle tip can be achieved with no reduction in the tip cross-sectional area for contact of liquid to be atomized. Therefore, the required electric drive power should be drastically reduced, decreasing the likelihood of transducer failure in ultrasonic atomization.

  4. Ultrasonic motors using piezoelectric ceramic multimode vibrators.

    Science.gov (United States)

    Takano, T; Tomikawa, Y; Ogasawara, T; Sugawara, S; Konno, M

    1990-01-01

    The development is reported of an ultrasonic motor using piezoelectric ceramic multimode vibrators consisting of circular or annular plates in which degenerate horizontal vibration modes of the same or different form are used. Two orthogonal nonaxisymmetric vibration modes were used in the same-form case, and the combination of a nonaxisymmetric vibration mode and a radial vibration mode was used in the different-forms case. Some details of the motor design and its experimental characteristics are presented. The ultrasonic motor presented here has a special advantage in its thin construction.

  5. Magnetic and ultrasonic investigations on magnetite nanofluids.

    Science.gov (United States)

    Nabeel Rashin, M; Hemalatha, J

    2012-12-01

    Magnetite nanofluids of various concentrations have been prepared through co-precipitation method. The structural and magnetic properties of the magnetic nanofluids have been analyzed which respectively revealed their face centered cubic crystal structure and super paramagnetic behavior. Ultrasonic investigations have been made for the nanofluids at different temperatures and magnetic fields. Open- and close-packed water structure is considered to explain the temperature effects. The inter particle interactions of surface modified nanomagnetite particle and the cluster formation are realized through the variations in ultrasonic parameters.

  6. Ultrasonic methods in solid state physics

    CERN Document Server

    Truell, John; Elbaum, Charles

    1969-01-01

    Ultrasonic Methods in Solid State Physics is devoted to studies of energy loss and velocity of ultrasonic waves which have a bearing on present-day problems in solid-state physics. The discussion is particularly concerned with the type of investigation that can be carried out in the megacycle range of frequencies from a few megacycles to kilomegacycles; it deals almost entirely with short-duration pulse methods rather than with standing-wave methods. The book opens with a chapter on a classical treatment of wave propagation in solids. This is followed by separate chapters on methods and techni

  7. Absorption and dispersion of ultrasonic waves

    CERN Document Server

    Herzfeld, Karl F; Massey, H S W; Brueckner, Keith A

    1959-01-01

    Absorption and Dispersion of Ultrasonic Waves focuses on the influence of ultrasonics on molecular processes in liquids and gases, including hydrodynamics, energy exchange, and chemical reactions. The book first offers information on the Stokes-Navier equations of hydrodynamics, as well as equations of motion, viscosity, formal introduction of volume viscosity, and linearized wave equation for a nonviscous fluid. The manuscript then ponders on energy exchange between internal and external degrees of freedom as relaxation phenomenon; effect of slow energy exchange on sound propagation; differe

  8. Characterization methods for ultrasonic test systems

    Energy Technology Data Exchange (ETDEWEB)

    Busse, L.J.; Becker, F.L.; Bowey, R.E.; Doctor, S.R.; Gribble, R.P.; Posakony, G.J.

    1982-07-01

    Methods for the characterization of ultrasonic transducers (search units) and instruments are presented. The instrument system is considered as three separate components consisting of a transducer, a receiver-display, and a pulser. The operation of each component is assessed independently. The methods presented were chosen because they provide the greatest amount of information about component operation and were not chosen based upon such conditions as cost, ease of operation, field implementation, etc. The results of evaluating a number of commercially available ultrasonic test instruments are presented.

  9. Model validation of untethered, ultrasonic neural dust motes for cortical recording.

    Science.gov (United States)

    Seo, Dongjin; Carmena, Jose M; Rabaey, Jan M; Maharbiz, Michel M; Alon, Elad

    2015-04-15

    A major hurdle in brain-machine interfaces (BMI) is the lack of an implantable neural interface system that remains viable for a substantial fraction of the user's lifetime. Recently, sub-mm implantable, wireless electromagnetic (EM) neural interfaces have been demonstrated in an effort to extend system longevity. However, EM systems do not scale down in size well due to the severe inefficiency of coupling radio-waves at those scales within tissue. This paper explores fundamental system design trade-offs as well as size, power, and bandwidth scaling limits of neural recording systems built from low-power electronics coupled with ultrasonic power delivery and backscatter communication. Such systems will require two fundamental technology innovations: (1) 10-100 μm scale, free-floating, independent sensor nodes, or neural dust, that detect and report local extracellular electrophysiological data via ultrasonic backscattering and (2) a sub-cranial ultrasonic interrogator that establishes power and communication links with the neural dust. We provide experimental verification that the predicted scaling effects follow theory; (127 μm)(3) neural dust motes immersed in water 3 cm from the interrogator couple with 0.002064% power transfer efficiency and 0.04246 ppm backscatter, resulting in a maximum received power of ∼0.5 μW with ∼1 nW of change in backscatter power with neural activity. The high efficiency of ultrasonic transmission can enable the scaling of the sensing nodes down to 10s of micrometer. We conclude with a brief discussion of the application of neural dust for both central and peripheral nervous system recordings, and perspectives on future research directions.

  10. Participatory Communication

    DEFF Research Database (Denmark)

    Tufte, Thomas

    This user guide on participatory communication aims to answer the following questions: What do we mean when we say participatory communication? What are the practical implications of working with participatory communication strategies in development and social change processes? What practical...... experiences document that participatory communication adds value to a development project or program? Many communication practitioners and development workers face obstacles and challenges in their practical work. A participatory communication strategy offers a very specific perspective on how to articulate......, tools, and experiences on how to implement participatory communications strategies. It is targeted toward government officials, World Bank staff, develompent workers in the field, and civil society....

  11. Degree of dispersion monitoring by ultrasonic transmission technique and excitation of the transducer's harmonics

    Science.gov (United States)

    Schober, G.; Heidemeyer, P.; Kretschmer, K.; Bastian, M.; Hochrein, T.

    2014-05-01

    The degree of dispersion of filled polymer compounds is an important quality parameter for various applications. For instance, there is an influence on the chroma in pigment colored plastics or on the mechanical properties of filled or reinforced compounds. Most of the commonly used offline methods are work-intensive and time-consuming. Moreover, they do not allow an all-over process monitoring. In contrast, the ultrasonic technique represents a suitable robust and process-capable inline method. Here, we present inline ultrasonic measurements on polymer melts with a fundamental frequency of 1 MHz during compounding. In order to extend the frequency range we additionally excite the fundamental and the odd harmonics vibrations at 3 and 5 MHz. The measurements were carried out on a compound consisting of polypropylene and calcium carbonate. For the simulation of agglomerates calcium carbonate with a larger particle size was added with various rates. The total filler content was kept constant. The frequency selective analysis shows a linear correlation between the normalized extinction and the rate of agglomerates simulated by the coarser filler. Further experiments with different types of glass beads with a well-defined particle size verify these results. A clear correlation between the normalized extinction and the glass bead size as well as a higher damping with increasing frequency corresponds to the theoretical assumption. In summary the dispersion quality can be monitored inline by the ultrasonic technique. The excitation of the ultrasonic transducer's harmonics generates more information about the material as the usage of the pure harmonic vibration.

  12. Vibration characteristics of ultrasonic complex vibration for hole machining

    Science.gov (United States)

    Asami, Takuya; Miura, Hikaru

    2012-05-01

    Complex vibration sources that use diagonal slits as a longitudinal-torsional vibration converter have been applied to ultrasonic motors, ultrasonic rock drilling, and ultrasonic welding. However, there are few examples of the application of these sources to ultrasonic machining in combination with an abrasive. Accordingly, a new method has been developed for machining of holes in brittle materials by using the ultrasonic longitudinal and torsional vibration of a hollow-type stepped horn with a diagonal slit vibration converter. In this paper, we compared vibration of a uniform rod and a hollow-type stepped horn, both with diagonal slits, when the conditions of the diagonal slits are constant.

  13. Preparation of thermal barrier coatings by ultrasonic plasma spraying

    Institute of Scientific and Technical Information of China (English)

    WEN Xiong-wei; LI Lu-ming; ZHANG Hua-tang; HAO Hong-wei; LU Zhi-qing

    2004-01-01

    Modulated plasma arc not only can heat the powder, but also can excite ultrasonic of different frequencies and different powers. The principles and characters of the plasma arc-excited ultrasonic were described, and the ultrasonic plasma spraying was compared with normal plasma spraying. Zirconia thermal barrier coatings (TBCs) were fabricated with two kinds of method. The TBCs were studied by the optical microscope observation, SEM observation and bonding strength experiment. The results show that suitable ultrasonic changes the performance and microstructure of TBCs in evidence. And the mechanism of ultrasonic influencing the TBCs was also discussed.

  14. Optimal Cooperative Searching Using Purely Repulsive Interactions

    CERN Document Server

    Tani, Noriyuki P; Quint, David A; Gopinathan, Ajay

    2013-01-01

    Foraging, either solitarily or collectively, is a necessary behavior for survival that is demonstrated by many organisms. Foraging can be collectively optimized by utilizing communication between the organisms. Examples of such communication range from high level strategic foraging by animal groups to rudimentary signaling among unicellular organisms. Here we systematically study the simplest form of communication via long range repulsive interactions between two diffusing Brownian searchers on a one-dimensional lattice. We show that the mean first passage time for either of them to reach a fixed target depends non-monotonically on the range of the interaction and can be optimized for a repulsive range that is comparable to the average spacing between searchers. Our results suggest that even the most rudimentary form of collective searching does in fact lower the search time for the foragers suggesting robust mechanisms for search optimization in cellular communities

  15. Improving Weld Quality by Arc-Excited Ultrasonic Treatment

    Institute of Scientific and Technical Information of China (English)

    张春雷; 吴敏生; 杜敬磊

    2001-01-01

    Ultrasonic treatment of the solidifying metal is a promising method for improving the quality of fusion welding. A method to combine the ultrasonic waves to the welding process using arc-excited ultrasonic emission, called arc-ultrasonic, was high frequency modulation of the arc-plasma. The effects of arc-ultrasonic on the weld including the fusion zone, the partially melted zone and the heat-affected zone are described. The arc-ultrasonic energy changes the weld microstructure. In the fusion zone, the primary dendrite arm spacing decreases significantly and more acicular ferrite appears. In the partially melted zone, a large amount of fine grains appear. In the heat-affected zone, the width of the tempered zone increases with increasing modulation frequency and the microstructure is refined. The results show that arc-ultrasonic is a new and effective way for improving weld quality.

  16. Lithium niobate ultrasonic transducer design for Enhanced Oil Recovery.

    Science.gov (United States)

    Wang, Zhenjun; Xu, Yuanming; Gu, Yuting

    2015-11-01

    Due to the strong piezoelectric effect possessed by lithium niobate, a new idea that uses lithium niobate to design high-power ultrasonic transducer for Enhanced Oil Recovery technology is proposed. The purpose of this paper is to lay the foundation for the further research and development of high-power ultrasonic oil production technique. The main contents of this paper are as follows: firstly, structure design technique and application of a new high-power ultrasonic transducer are introduced; secondly, the experiment for reducing the viscosity of super heavy oil by this transducer is done, the optimum ultrasonic parameters for reducing the viscosity of super heavy oil are given. Experimental results show that heavy large molecules in super heavy oil can be cracked into light hydrocarbon substances under strong cavitation effect caused by high-intensity ultrasonic wave. Experiment proves that it is indeed feasible to design high-power ultrasonic transducer for ultrasonic oil production technology using lithium niobate.

  17. Viscoacoustic model for near-field ultrasonic levitation.

    Science.gov (United States)

    Melikhov, Ivan; Chivilikhin, Sergey; Amosov, Alexey; Jeanson, Romain

    2016-11-01

    Ultrasonic near-field levitation allows for contactless support and transportation of an object over vibrating surface. We developed an accurate model predicting pressure distribution in the gap between the surface and levitating object. The formulation covers a wide range of the air flow regimes: from viscous squeezed flow dominating in small gap to acoustic wave propagation in larger gap. The paper explains derivation of the governing equations from the basic fluid dynamics. The nonreflective boundary conditions were developed to properly define air flow at the outlet. Comparing to direct computational fluid dynamics modeling our approach allows achieving good accuracy while keeping the computation cost low. Using the model we studied the levitation force as a function of gap distance. It was shown that there are three distinguished flow regimes: purely viscous, viscoacoustic, and acoustic. The regimes are defined by the balance of viscous and inertial forces. In the viscous regime the pressure in the gap is close to uniform while in the intermediate viscoacoustic and the acoustic regimes the pressure profile is wavy. The model was validated by a dedicated levitation experiment and compared to similar published results.

  18. Ultrasonic Mastering of Filter Flow and Antifouling of Renewable Resources.

    Science.gov (United States)

    Radziuk, Darya; Möhwald, Helmuth

    2016-04-04

    Inadequate access to pure water and sanitation requires new cost-effective, ergonomic methods with less consumption of energy and chemicals, leaving the environment cleaner and sustainable. Among such methods, ultrasound is a unique means to control the physics and chemistry of complex fluids (wastewater) with excellent performance regarding mass transfer, cleaning, and disinfection. In membrane filtration processes, it overcomes diffusion limits and can accelerate the fluid flow towards the filter preventing antifouling. Here, we outline the current state of knowledge and technological design, with a focus on physicochemical strategies of ultrasound for water cleaning. We highlight important parameters of ultrasound for the delivery of a fluid flow from a technical perspective employing principles of physics and chemistry. By introducing various ultrasonic methods, involving bubbles or cavitation in combination with external fields, we show advancements in flow acceleration and mass transportation to the filter. In most cases we emphasize the main role of streaming and the impact of cavitation with a perspective to prevent and remove fouling deposits during the flow. We also elaborate on the deficiencies of present technologies and on problems to be solved to achieve a wide-spread application. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Crack path in aeronautical titanium alloy under ultrasonic torsion loading

    Directory of Open Access Journals (Sweden)

    A. Nikitin

    2016-01-01

    Full Text Available This paper discusses features of fatigue crack initiation and growth in aeronautical VT3-1 titanium alloy under pure torsion loading in gigacycle regime. Two materials: extruded and forged VT3-1 titanium alloys were studied. Torsion fatigue tests were performed up to fatigue life of 109 cycles. The results of the torsion tests were compared with previously obtained results under fully reversed axial loading on the same alloys. It has been shown that independently on production process as surface as well subsurface crack initiation may appear under ultrasonic torsion loading despite the maximum stress amplitude located at the specimen surface. In the case of surface crack initiation, a scenario of crack initiation and growth is similar to HCF regime except an additional possibility for internal crack branching. In the case of subsurface crack, the initiation site is located below the specimen surface (about 200 μm and is not clearly related to any material flaw. Internal crack initiation is produced by shear stress in maximum shear plane and early crack growth is in Mode II. Crack branching is limited in the case of internal crack initiation compared to surface one. A typical ‘fish-eye’ crack can be observed at the torsion fracture surface, but mechanism of crack initiation seems not to be the same than under axial fatigue loading.

  20. Pure transperitoneal laparoscopic correction of retrocaval ureter

    Institute of Scientific and Technical Information of China (English)

    DING Guo-qing; XU Li-wei; LI Xin-de; LI Gong-hui; YU Yan-lan; YU Da-min; ZHANG Zhi-gen

    2012-01-01

    Background Retrocaval ureter is a rare congenital abnormality.Operative repair is always suggested in cases of significant functional obstruction.Laparoscopic procedures have been employed as the minimally invasive therapeutic option for retrocaval ureter.However,the laparoscopic techniques for retrocaval ureter might be technically challenging to some surgeons.The aim of this article was to present our experience and surgical techniques of pure transperitoneal laparoscopic pyelopyelostomy and ureteroureterostomy in nine patients with retrocaval ureter.Methods A total of nine patients of retrocaval ureter underwent pure laparoscopic pyelopyelostomy or ureteroureterostomy.The operation was performed with the patients placed in the 70-degree lateral decubitus position via a three port transperitoneal approach with two 10-mm and one 5-mm ports.The distal part of the dilated renal pelvis was transected at the ureteropelvic junction and the ureter was relocated anterior to the inferior vena cava.The tension-free pyeloureteral or ureteroureteral anastomosis was completed with the intracorporal freehand suturing and in situ knot-tying techniques combined with interrupted and continuous fashion.A double J ureteral stent was inserted in an antegrade manner during laparoscopy.Intravenous urography or computerized tomography and renal ultrasonography were performed after 3 months postoperatively.Results All operations were completed laparoscopically,and no open conversion was required.The mean operative time was 135 minutes (range,70-250 minutes),with minimal blood loss (less than 60 ml).No intra-operative complications or significant bleeding occurred.All patients presented mild postoperative pain and quick convalescence.The symptoms disappeared and hydronephrosis decreased substantially after surgery.Conclusions Pure transperitoneal laparoscopic correction for retrocaval ureter was associated with an excellent outcome,minimal invasiveness and short hospital stay.It is

  1. Needleless Electrospinning of Pure and Blended Chitosan

    Science.gov (United States)

    Grimmelsmann, Nils; Homburg, Sarah Vanessa; Ehrmann, Andrea

    2017-08-01

    Chitosan is a biopolymer with bactericidal, fungicidal, hemostatic and other interesting properties. It can be used, e.g., in medical products, as a filter medium, in biotechnological purposes etc. For these possible applications, nanofiber mats with a large inner surface will be most efficient. This is why in a recent project, the electrospinning properties of pure chitosan as well as chitosan blended with poly(ethylene oxide) were investigated. Using a needleless nanospinning process, the technology under examination can be upscaled from lab to industrial scale, enabling direct transfer of the gained experiences to the intended application.

  2. Pure spinor equations to lift gauged supergravity

    Energy Technology Data Exchange (ETDEWEB)

    Rosa, Dario; Tomasiello, Alessandro [Dipartimento di Fisica, Università di Milano-Bicocca, and INFN, sezione di Milano-Bicocca,I-20126 Milano (Italy)

    2014-01-31

    We rewrite the equations for ten-dimensional supersymmetry in a way formally identical to a necessary and sufficient G-structure system in N=2 gauged supergravity, where all four-dimensional quantities are replaced by combinations of pure spinors and fluxes in the internal space. This provides a way to look for lifts of BPS solutions without having to reduce or even rewrite the ten-dimensional action. In particular this avoids the problem of consistent truncation, and the introduction of unphysical gravitino multiplets.

  3. Are all maximally entangled states pure?

    Science.gov (United States)

    Cavalcanti, D.; Brandão, F. G. S. L.; Terra Cunha, M. O.

    2005-10-01

    We study if all maximally entangled states are pure through several entanglement monotones. In the bipartite case, we find that the same conditions which lead to the uniqueness of the entropy of entanglement as a measure of entanglement exclude the existence of maximally mixed entangled states. In the multipartite scenario, our conclusions allow us to generalize the idea of the monogamy of entanglement: we establish the polygamy of entanglement, expressing that if a general state is maximally entangled with respect to some kind of multipartite entanglement, then it is necessarily factorized of any other system.

  4. Purely cubic action for string field theory

    Science.gov (United States)

    Horowitz, G. T.; Lykken, J.; Rohm, R.; Strominger, A.

    1986-01-01

    It is shown that Witten's (1986) open-bosonic-string field-theory action and a closed-string analog can be written as a purely cubic interaction term. The conventional form of the action arises by expansion around particular solutions of the classical equations of motion. The explicit background dependence of the conventional action via the Becchi-Rouet-Stora-Tyutin operator is eliminated in the cubic formulation. A closed-form expression is found for the full nonlinear gauge-transformation law.

  5. Synthesis of highly phase pure BSCCO superconductors

    Science.gov (United States)

    Dorris, S.E.; Poeppel, R.B.; Prorok, B.C.; Lanagan, M.T.; Maroni, V.A.

    1995-11-21

    An article and method of manufacture (Bi, Pb)-Sr-Ca-Cu-O superconductor are disclosed. The superconductor is manufactured by preparing a first powdered mixture of bismuth oxide, lead oxide, strontium carbonate, calcium carbonate and copper oxide. A second powdered mixture is then prepared of strontium carbonate, calcium carbonate and copper oxide. The mixtures are calcined separately with the two mixtures then combined. The resulting combined mixture is then subjected to a powder in tube deformation and thermal processing to produce a substantially phase pure (Bi, Pb)-Sr-Ca-Cu-O superconductor. 5 figs.

  6. Quantum correlations support probabilistic pure state cloning

    Energy Technology Data Exchange (ETDEWEB)

    Roa, Luis, E-mail: lroa@udec.cl [Departamento de Física, Universidad de Concepción, Casilla 160-C, Concepción (Chile); Alid-Vaccarezza, M.; Jara-Figueroa, C. [Departamento de Física, Universidad de Concepción, Casilla 160-C, Concepción (Chile); Klimov, A.B. [Departamento de Física, Universidad de Guadalajara, Avenida Revolución 1500, 44420 Guadalajara, Jalisco (Mexico)

    2014-02-01

    The probabilistic scheme for making two copies of two nonorthogonal pure states requires two auxiliary systems, one for copying and one for attempting to project onto the suitable subspace. The process is performed by means of a unitary-reduction scheme which allows having a success probability of cloning different from zero. The scheme becomes optimal when the probability of success is maximized. In this case, a bipartite state remains as a free degree which does not affect the probability. We find bipartite states for which the unitarity does not introduce entanglement, but does introduce quantum discord between some involved subsystems.

  7. Pure seminoma: A review and update

    Science.gov (United States)

    2011-01-01

    Pure seminoma is a rare pathology of the young adult, often discovered in the early stages. Its prognosis is generally excellent and many therapeutic options are available, especially in stage I tumors. High cure rates can be achieved in several ways: standard treatment with radiotherapy is challenged by surveillance and chemotherapy. Toxicity issues and the patients' preferences should be considered when management decisions are made. This paper describes firstly the management of primary seminoma and its nodal involvement and, secondly, the various therapeutic options according to stage. PMID:21819630

  8. [XX 'pure' gonadal dysgenesis and XYY syndrome].

    Science.gov (United States)

    Itoh, Naoki; Tsukamoto, Taiji

    2004-02-01

    XX 'pure' gonadal dysgenesis is a disease related to Turner's syndrome. Patients of this disease are characterized by normal female external genitalia, bilateral streak gonads, amenorrhea and sexual infantilism. Recently, it has been reported that point mutations of the FSH receptor gene may be one of cause of this disease. The relationship between criminal behavior and XYY syndrome is still controversial. Increased incidence of disomic sperm in 47,XYY males has been reported by fluorescent in situ hybridization(FISH). Genetic counseling should be done when they undergo intracytoplasmic sperm injection.

  9. Synthesis of pure Portland cement phases

    DEFF Research Database (Denmark)

    Wesselsky, Andreas; Jensen, Ole Mejlhede

    2009-01-01

    Pure phases commonly found in Portland cement clinkers are often used to test cement hydration behaviour in simplified experimental conditions. The synthesis of these phases is covered in this paper, starting with a description of phase relations and possible polymorphs of the four main phases...... in Portland cement, i.e. tricalcium silicate, dicalcium silicate, tricalcium aluminate and tetracalcium alumino ferrite. Details of the The process of solid state synthesis are is described in general including practical advice on equipment and techniques. Finally In addition, some exemplary mix compositions...

  10. Powder injection molding of pure titanium

    Institute of Scientific and Technical Information of China (English)

    GUO Shibo; DUAN Bohua; HE Xinbo; QU Xuanhui

    2009-01-01

    An improved wax-based binder was developed for powder injection molding of pure titanium. A critical powder loading of 69 vol.% and a pseudo-plastic flow behavior were obtained by the feedstock based on the binder. The injection molding, debinding, and sintering process were studied. An ideal control of carbon and oxygen contents was achieved by thermal debinding in vacuum atmosphere (10-3 Pa). The mechanical properties of as-sintered specimens were less than those of titanium made by the conventional press-sintering process. Good shape retention and ±0.04 mm dimension deviation were achieved.

  11. Study on pure silica core optical fibers

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    An optimal refractive index profile of pure silica core optical fiber (PSCF) was designed, in combination with the characters of the modified chemical vapor deposition (MCVD) process. Techniques of preform fabrication by a new furnace round heating MCVD process and fiber drawing process were reviewed. Difficulties in doping fluorine in silica, widening the depressed-index cladding and maintaining the index of fiber core were discussed. Methods used to overcome these difficulties were given at the same time. Additionally, the optimal refractive index profiles of PSCF were presented.

  12. Purely cubic action for string field theory

    Science.gov (United States)

    Horowitz, G. T.; Lykken, J.; Rohm, R.; Strominger, A.

    1986-01-01

    It is shown that Witten's (1986) open-bosonic-string field-theory action and a closed-string analog can be written as a purely cubic interaction term. The conventional form of the action arises by expansion around particular solutions of the classical equations of motion. The explicit background dependence of the conventional action via the Becchi-Rouet-Stora-Tyutin operator is eliminated in the cubic formulation. A closed-form expression is found for the full nonlinear gauge-transformation law.

  13. The Pure Virtual Braid Group Is Quadratic

    CERN Document Server

    Lee, Peter

    2011-01-01

    If an augmented algebra K over Q is filtered by powers of its augmentation ideal I, the associated graded algebra gr_I K need not in general be quadratic: although it is generated in degree 1, its relations may not be generated by homogeneous relations of degree 2. In this paper we give a criterion which is equivalent to gr_I K being quadratic. We apply this criterion to the group algebra of the pure virtual braid group (also known as the quasi-triangular group), and show that the corresponding associated graded algebra is quadratic.

  14. Purely Four-dimensional Viable Anomaly Mediation

    CERN Document Server

    Harnik, R; Pierce, A T; Harnik, Roni; Murayama, Hitoshi; Pierce, Aaron

    2002-01-01

    Anomaly mediation of supersymmetry breaking solves the supersymmetric flavor problem thanks to its ultraviolet-insensitivity. However, it suffers from two problems: sleptons have negative masses-squared, and there are likely bulk moduli that spoil the framework. Here, we present the first fully ultraviolet-insensitive model of anomaly mediation with positive slepton masses-squared in a purely four-dimensional framework. Our model is based on the additional D-term contributions to the sparticle masses of Arkani-Hamed, Kaplan, HM, and Nomura, and the conformal sequestering mechanism of Luty and Sundrum.

  15. Measure and integral with purely ordinal scales

    CERN Document Server

    Denneberg, Dieter

    2008-01-01

    We develop a purely ordinal model for aggregation functionals for lattice valued functions, comprising as special cases quantiles, the Ky Fan metric and the Sugeno integral. For modeling findings of psychological experiments like the reflection effect in decision behaviour under risk or uncertainty, we introduce reflection lattices. These are complete linear lattices endowed with an order reversing bijection like the reflection at 0 on the real interval $[-1,1]$. Mathematically we investigate the lattice of non-void intervals in a complete linear lattice, then the class of monotone interval-valued functions and their inner product.

  16. Electrostatic Precipitation in Nearly Pure Gaseous Nitrogen

    Science.gov (United States)

    Buhler, Charles; Calle, Carlos; Clements, Sid; Cox, Bobby; Ritz, Mindy

    2008-01-01

    Electrostatic precipitation was performed in a nearly pure gaseous nitrogen system as a possible remedy for black dust contaminant from high pressure 6000 psi lines at the NASA Kennedy Space Center. The results of a prototype electrostatic precipitator that was built and tested using nitrogen gas at standard atmospheric pressures is presented. High voltage pulsed waveforms are generated using a rotating spark gap system at 30 Hz. A unique dust delivery system utilizing the Venturi effect was devised that supplies a given amount of dust per unit time for testing purposes.

  17. Defective spatial imagery with pure Gerstmann's syndrome.

    Science.gov (United States)

    Carota, Antonio; Di Pietro, Marie; Ptak, Radek; Poglia, Davide; Schnider, Armin

    2004-01-01

    Gerstmann's syndrome comprises finger agnosia, peripheral agraphia, anarithmetia, and right-left confusion. We here report a single-case study of an 85-year-old ambidextrous man who exhibited pure Gerstmann's syndrome (i.e., without aphasia) 10 weeks after a stroke involving the angular gyrus in the left parietal lobe. We hypothesize that, in this case, the main cognitive denominator of Gerstmann's tetrad was a severe dysfunction in mental rotation and translation. This report provides further evidence for the spatial nature of Gerstmann's syndrome.

  18. CSR communication

    DEFF Research Database (Denmark)

    Golob, Ursa; Podnar, Klement; Elving, Wim

    2013-01-01

    Purpose – This paper aims to introduce the special issue on CSR communication attached to the First International CSR Communication Conference held in Amsterdam in October 2011. The aim of the introduction is also to review CSR communication papers published in scholarly journals in order to make...... a summary of the state of CSR communication knowledge. Design/methodology/approach – The existing literature on CSR communication was approached via systematic review. with a combination of conventional and summative qualitative content analysis. The final dataset contained 90 papers from two main business...... communications. The most important outlets for CSR communication-related topics are Journal of Business Ethics and Corporate Communications: An International Journal. Originality/value – This paper represents the first attempt to perform a systematic and comprehensive overview of CSR communication papers...

  19. Ultrasonic testing of reactive powder concrete.

    Science.gov (United States)

    Washer, Glenn; Fuchs, Paul; Graybeal, Benjamin A; Hartmann, Joseph Lawrence

    2004-02-01

    Concrete is a critical material for the construction of infrastructure facilities throughout the world. Traditional concretes consist of cement paste and aggregates ranging in size from 6 to 25 mm that form a heterogeneous material with substantial compressive strength and a very low tensile strength. Steel reinforcement is used to provide tensile strength for reinforced concrete structures and as a composite the material is useful for structural applications. A new material known as reactive powder concrete (RPC) is becoming available. It differs significantly from traditional concrete; RPC has no large aggregates, and contains small steel fibers that provide additional strength and, in some cases, can replace traditional steel reinforcement. Due to its high density and lack of aggregates, ultrasonic inspections at frequencies 10 to 20 times that of traditional concrete inspections are possible. This paper reports on the initial findings of research conducted to determine the applicability of ultrasonic testing techniques for the condition assessment of RPC. Pulse velocities for shear and longitudinal waves and ultrasonic measurement of the modulus of elasticity for RPC are reported. Ultrasonic crack detection for RPC also is investigated.

  20. Ultrasonic scanning for pallet part grading

    Science.gov (United States)

    Mohammed F. Kabir; Daniel L. Schmoldt; Mark E. Schafer; Philip A. Araman

    2000-01-01

    Sorting and grading of wooden pallet parts are key factors for pallet manufacturing quality and pallet durability. The feasibility of ultrasonic scanning for defect detection in pallet manufacturing is examined in this report. Scanning was conducted by two pressure-contact rolling transducers in a pitch-catch arrangement. Pallet part deckboards were fed through the...

  1. 21 CFR 890.5300 - Ultrasonic diathermy.

    Science.gov (United States)

    2010-04-01

    ... beyond 20 kilohertz and that is intended to generate deep heat within body tissues for the treatment of selected medical conditions such as relief of pain, muscle spasms, and joint contractures, but not for the treatment of malignancies. (2) Classification. Class II (performance standards). (b) Ultrasonic...

  2. Experimental development of an ultrasonic linear motor

    CSIR Research Space (South Africa)

    M'Boungui, G

    2010-01-01

    Full Text Available The authors investigate a novel ultrasonic motor which generates a stator trajectory in the form of a figure-of-eight by superimposing two resonant modes, with one double the frequency of the other. Topology optimization was used to design...

  3. Dry calibration of ultrasonic gas flow meters

    Energy Technology Data Exchange (ETDEWEB)

    De Boer, G.; Lansing, J.

    1997-07-01

    At present in most European countries it is customary that turbine meters, or the newer ultrasonic gas flow meters, when used in fiscal metering or custody transfer metering applications, are calibrated in a test facility by comparison to standards or reference devices. For reason of practical and operational drawbacks, costs involved and availability of only a limited number of calibration facilities, another way of meter verification is advantageous. For orifice metering the practice of dry calibration is well established; that is, meter verification is based upon examination of the geometry and installation of the orifice plate and a function check of the read out devices. Although for turbine meters a flow (wet) calibration may be a necessity, it will be shown that ultrasonic gas flow meters can be dry calibrated in the same way as orifice meters. As a basis for the acceptance of a dry calibration procedure for ultrasonic gas flow meters, a sensitivity analysis of the relevant variables with respect to the meter's accuracy is presented. Further test results are presented that demonstrate the feasibility of the concept of dry calibration applied to ultrasonic gas flow meters. (author)

  4. High-intensity, focused ultrasonic fields

    DEFF Research Database (Denmark)

    Jensen, Leif Bjørnø

    1988-01-01

    distribution, etc. involving nonlinearity, diffraction, and absorption in the high-intensity focused ultrasonic fields produced by an ellipsoid as well as a spherical cap focusing geometry. Data from the development of an ESWL of the piezoelectric disk type are reported including demands to transducers...

  5. Characterization of Ultrasonic Transducers. Measurement report

    DEFF Research Database (Denmark)

    Wilhjelm, Jens Erik

    1996-01-01

    This report contains the first results of a field measurement program for characterizing ultrasonic transducers in use at the Department. Specifically, a number of Panametrics Inc, transducers are characterized by using a 0.1 mm point scatterer as target, which is moved in front of the transdcuer....

  6. Ultrasonic Cold Forming of Aircraft Sheet Materials

    Science.gov (United States)

    1981-01-01

    in such ultrasonic deformation processes as forging, extrusion, tube, rod, and wire drawing . This type of cold forminy could have a decided impact on...tightening of threaded fasteners. This phenomenon is particularly important in dynamic forming pro- cesses such as tube and wire drawing , extrusion

  7. Electronic power generators for ultrasonic frequencies

    Science.gov (United States)

    Ciovica, D.

    1974-01-01

    The design and construction of an ultrasonic frequency electronic power generator are discussed. The principle design elements of the generator are illustrated. The generator provides an inductive load with an output power of two kilowatts and a variable output frequency in the fifteen to thirty KiloHertz range. The method of conducting the tests and the results obtained with selected materials are analyzed.

  8. Materials characterization of propellants using ultrasonics

    Science.gov (United States)

    Workman, Gary L.; Jones, David

    1993-01-01

    Propellant characteristics for solid rocket motors were not completely determined for its use as a processing variable in today's production facilities. A major effort to determine propellant characteristics obtainable through ultrasonic measurement techniques was performed in this task. The information obtained was then used to determine the uniformity of manufacturing methods and/or the ability to determine non-uniformity in processes.

  9. Plastic Anisotropy Prediction by Ultrasonic Texture Data

    OpenAIRE

    Serebryany, V. N.

    1996-01-01

    The plastic anisotropy parameters (R coefficient and height of ears of the drawn cup) have been calculated from ultrasonic orientation distribution function (ODF) coefficients on the basis of Taylor theory for low carbon steel and aluminium alloy sheets. The ODF coefficients were defined by Sayers method and using the iterative procedure on the basis of measurement of bulk longitudinal and shear wave time delays.

  10. New camera tube improves ultrasonic inspection system

    Science.gov (United States)

    Berger, H.; Collis, W. J.; Jacobs, J. E.

    1968-01-01

    Electron multiplier, incorporated into the camera tube of an ultrasonic imaging system, improves resolution, effectively shields low level circuits, and provides a high level signal input to the television camera. It is effective for inspection of metallic materials for bonds, voids, and homogeneity.

  11. Bacterial aerosolization from an ultrasonic cleaner.

    Science.gov (United States)

    Turner, A G; Wilkins, J R; Craddock, J G

    1975-03-01

    An ultrasonic device used for cleaning surgical instruments was found to produce a significant microbial aerosol. No correlation was found between the concentration of aerosol generated and the bacterial contamination in the cleaning solution. Table top contamination around the cleaner was due essentially to splash and dripping, and not from the settling of the aerosol. Recommendations are made for cleaning and disinfection protocols.

  12. Ultrasonic Study of Osmium and Ruthenium

    National Research Council Canada - National Science Library

    Pandey, D.K; Singh, Devraj; Yadawa, P.K

    2009-01-01

    .... The nature of the angle-dependent ultrasonic velocity is found to be similar to those of molybdenum-ruthenium-rhodium-palladium alloys, Group III nitrides and lave-phase compounds such as TiCr2, ZrCr2 and HfCr2...

  13. The Effect of Welding Energy on the Microstructural and Mechanical Properties of Ultrasonic-Welded Copper Joints

    Directory of Open Access Journals (Sweden)

    Jingwei Yang

    2017-02-01

    Full Text Available The effects of welding energy on the mechanical and microstructural characteristics of ultrasonic-welded pure copper plates were investigated. Complex dynamic recrystallization and grain growth occurred inside the weld zone during ultrasonic welding. At a low welding energy, a thin band of straight weld interfaces was observed and had an ultra-fine grain structure. With an increase in welding energy, the weld interface progressively changed from flat to sinusoidal, and eventually turned into a convoluted wavy pattern, bearing similarities to shear instabilities, as observed in fluid dynamics. The lap shear load of the joints initially increased and then remained stable as the welding energy increased. The tensile characteristics of the joints significantly depended on the development of plastic deformation at the interface. The influence of the microstructure on the hardness was also discussed.

  14. Scientific communication

    Directory of Open Access Journals (Sweden)

    Aleksander Kobylarek

    2017-09-01

    Full Text Available The article tackles the problem of models of communication in science. The formal division of communication processes into oral and written does not resolve the problem of attitude. The author defines successful communication as a win-win game, based on the respect and equality of the partners, regardless of their position in the world of science. The core characteristics of the process of scientific communication are indicated , such as openness, fairness, support, and creation. The task of creating the right atmosphere for science communication belongs to moderators, who should not allow privilege and differentiation of position to affect scientific communication processes.

  15. Communication skills.

    Science.gov (United States)

    Ellison, Deborah

    2015-03-01

    The front-line nurse is responsible for providing direct patient care, patient satisfaction, care coordination, policy, safety, and communication during a 12-hour shift. Every nurse has the opportunity to make a positive impact on patient outcomes through day-to-day advocacy for patients, nurses, and the nursing profession. Communication is a means of advocacy that provides the avenue to which a positive impact can be made. There are multiple barriers to effective communication in the day-to-day communication of the front-line nurse. Interprofessional communication and shared governance models offer ways to improve communication within nursing and within a systems approach.

  16. Pure sources and efficient detectors for optical quantum information processing

    Science.gov (United States)

    Zielnicki, Kevin

    Over the last sixty years, classical information theory has revolutionized the understanding of the nature of information, and how it can be quantified and manipulated. Quantum information processing extends these lessons to quantum systems, where the properties of intrinsic uncertainty and entanglement fundamentally defy classical explanation. This growing field has many potential applications, including computing, cryptography, communication, and metrology. As inherently mobile quantum particles, photons are likely to play an important role in any mature large-scale quantum information processing system. However, the available methods for producing and detecting complex multi-photon states place practical limits on the feasibility of sophisticated optical quantum information processing experiments. In a typical quantum information protocol, a source first produces an interesting or useful quantum state (or set of states), perhaps involving superposition or entanglement. Then, some manipulations are performed on this state, perhaps involving quantum logic gates which further manipulate or entangle the intial state. Finally, the state must be detected, obtaining some desired measurement result, e.g., for secure communication or computationally efficient factoring. The work presented here concerns the first and last stages of this process as they relate to photons: sources and detectors. Our work on sources is based on the need for optimized non-classical states of light delivered at high rates, particularly of single photons in a pure quantum state. We seek to better understand the properties of spontaneous parameteric downconversion (SPDC) sources of photon pairs, and in doing so, produce such an optimized source. We report an SPDC source which produces pure heralded single photons with little or no spectral filtering, allowing a significant rate enhancement. Our work on detectors is based on the need to reliably measure single-photon states. We have focused on

  17. The pure relationship and below replacement fertility

    Directory of Open Access Journals (Sweden)

    Hall, David R.

    2003-01-01

    Full Text Available Of the many changes which have characterized the second demographic transition, shifts in fertility and union formation have attracted a great deal of interest from demographers. Despite the fact that researchers have extensively modeled recent demographic changes such as skyrocketing divorce rates, rising common-law union formation, delayed childbearing, and the decline to below-replacement fertility levels, our understanding of the causes of these trends, and the possible connections between them remains theoretically fragmented and incomplete. The goal of this paper is to advance our understanding in this area by exploring the insights on modern family formation of prominent sociologist Anthony Giddens. Specifically, this study examines whether Giddens' "pure relationship" concept can shed light on the trend toward very low fertility. The results of this inquiry suggest that couples in both marriages and common-law unions who conform to key aspects of Giddens pure relationship are morel likely to have uncertain or below-replacement fertility intentions, and less likely to embrace above-replacement fertility goals.

  18. (Not so) pure Lovelock Kasner metrics

    CERN Document Server

    Camanho, Xián O; Molina, Alfred

    2016-01-01

    The gravitational interaction is expected to be modified for very short distances. This is particularly important in situations in which the curvature of spacetime is large in general, such as close to the initial cosmological singularity. The gravitational dynamics is then captured by the higher curvature terms in the action, making it difficult to reliably extrapolate any prediction of general relativity. In this note we review pure Lovelock equations for Kasner-type metrics. These equations correspond to a single $N$th order Lovelock term in the action in $d=2N+1,\\,2N+2$ dimensions, and they capture the relevant gravitational dynamics when aproaching the big-bang singularity within the Lovelock family of theories. These are classified in several isotropy types. Some of these families correspond to degenerate classes of solutions, such that their dynamics is not completely determined by the equations of pure Lovelock gravity. Instead, these Kasner solutions become sensitive to the subleading terms in the Lo...

  19. LHC Signals of Pure Gravity Mediation

    Directory of Open Access Journals (Sweden)

    Feldstein Brian

    2013-05-01

    Full Text Available Evidence is mounting that natural supersymmetry at the weak scale is not realized in nature. This evidence comes from collider searches, a lack of new flavor changing neutral current effects, and now also the size of the measured Higgs mass. On the other hand, string theory suggests that supersymmetry might be present at some energy scale, and gauge coupling unification and dark matter imply that that energy scale may be relatively low. The simplest model to address all of these hints is arguably “pure gravity mediation”, in which the scalar superpartner masses are taken to be perhaps 100 TeV, with gauginos automatically acquiring loop factor suppressed masses of order TeV. The gauginos might then be the only superpartners accessible to the LHC. Unification and LSP dark matter are maintained (with a wino LSP at the cost of a 10−5 or 10−6 fine tuning. Here I will discuss the structure and LHC phenomenology of pure gravity mediation.

  20. MRI of autosomal dominant pure spastic paraplegia

    Energy Technology Data Exchange (ETDEWEB)

    Krabbe, K.; Fallentin, E.; Herning, M. [Danish Research Center of Magnetic Resonance, Hvidovre Hospital, Kettegaard alle 30, DK-2650 Hvidovre (Denmark); Nielsen, J.E.; Fenger, K. [Institute of Medical Biochemistry and Genetics, Laboratory of Medical Genetics, Section of Neurogenetics, University of Copenhagen (Denmark)

    1997-10-01

    We examined 16 patients with autosomal dominant pure spastic paraplegia (HSP) and 15 normal controls matched for age and sex using MRI of the brain and spinal cord. Images were assessed qualitatively by two independent radiologists, blinded to the clinical diagnosis. Areas of the brain and corpus callosum on one midsagittal slice and the area of the brain on one axial slice were measured and a ``corpus-callosum index`` expressing the size of the corpus callosum relative to that of the brain was calculated. Cross-sectional areas and anteroposterior and transverse diameters of the spinal cord at the levels of C 2, C 5, T 3, T 6, T 9 and T 11 were measured. No significant differences between patients and controls were found on qualitative evaluation of the images. The patients had a significantly smaller corpus callosum and ``corpus-callosum index`` than controls. This finding, not reported previously, might indicate that the disease process in pure HSP is not confined to the spinal cord. The anteroposterior diameters of the spinal cord at T 3 and T 9 were significantly smaller in patients than in controls. This might correspond to the degeneration of the pyramidal tracts and the dorsal columns described at neuropathological examination. (orig.). With 1 fig., 3 tabs.

  1. Development of Soybean Highly Pure Powdered Lecithin

    Institute of Scientific and Technical Information of China (English)

    LiGuihua; GuKeren; LiangShaohua

    2002-01-01

    This project makes use of Condensed Soybean Phospholipids(CSP)to produce highly pure powdered soybean lecithin.In the production technology,the first step is to de-oil by continuously delivered material,high effective mixing CSP with acetone and circular extraction.The second step is to centrifugally separate the lecithin miscellaneous liquid into miscellaneous oil and solid-state lecithin with acetone.Then the mixing oil can be separated into crude oil and acetone by vaporization and condensation.If the acetone contains too much water,it shoud be rectified for use circularly.Solid state lecithin with acetone can be made into highly pure powdered soybean lecithin (acetone insoluble matter >95%)under the following conditions:vacuum 750mmHg,temperature 60℃,time 20 minutes.The production not only reaches the domestic and oversea quality index,but also has favorable hydrophilic property,which makes it become natural food additive and sanitarian nurture.

  2. Data communications

    Energy Technology Data Exchange (ETDEWEB)

    Preckshot, G.G. [Lawrence Livermore National Lab., CA (United States)

    1993-08-01

    The purpose of this paper is to recommend regulatory guidance for reviewers examining computer communication systems used in nuclear power plants. The recommendations cover three areas important to these communications systems: system design, communication protocols, and communication media. The first area, system design, considers three aspects of system design--questions about architecture, specific risky design elements or omissions to look for in designs being reviewed, and recommendations for multiplexed data communication systems used in safety systems. The second area reviews pertinent aspects of communication protocol design and makes recommendations for newly designed protocols or the selection of existing protocols for safety system, information display, and non-safety control system use. The third area covers communication media selection, which differs significantly from traditional wire and cable. The recommendations for communication media extend or enhance the concerns of published IEEE standards about three subjects: data rate, imported hazards and maintainability.

  3. 77 FR 46030 - Pure Magnesium in Granular Form From the People's Republic of China: Preliminary Results of...

    Science.gov (United States)

    2012-08-02

    ....213(b), for an administrative review of China Minmetals Non-Ferrous Metals Co., Ltd. (``CMN'') in the...: Email Communication from China Minmetals Non-Ferrous Metals Co., Ltd.'' dated April 20, 2012. We note... Specification for Magnesium Alloy'' \\8\\ (generally referred to as ``off-specification pure'' magnesium); and (4...

  4. Chapter 12. Pure Tap Water Hydraulic Systems and Applications

    DEFF Research Database (Denmark)

    Conrad, Finn; Adelstorp, Anders

    1997-01-01

    Presentation of developed a modern pure tap water hydraulic components (Nessie), systems and industrial applications.......Presentation of developed a modern pure tap water hydraulic components (Nessie), systems and industrial applications....

  5. Communication (action with communicative content).

    Science.gov (United States)

    Russo, M T

    2010-01-01

    The term Communication generally designate the transmission of a message of concepts, feelings or needs from a speaker to a receiver by means of verbal or no verbal language. The pragmatic approach to human communication has put in evidence a further implication of this concept: every behaviour therefore has a value even when it is not intentional. Recently, a more dynamic concept of communication has been elaborated where communication means communicative action. This interpretation is the starting point for the theory of the "communicative acting" and subsequently of the so called discourse ethic elaborated by J. Habermas.

  6. Communicative Writing

    Institute of Scientific and Technical Information of China (English)

    彭燕

    2016-01-01

    Writing, like all other aspects of language , is communicative.Communicative writing takes an important part in English learn-ing.Communicative writing assignments train students to turn personal observations into impersonal prose , avoid value judgments unwelcome in the sciences, and write with economy and precision .In the English language classroom , however, writing often lacks this.Why?There are lots of reasons , as there are lots of ways to make the writing we do with students more communicative .

  7. Participatory Communication

    DEFF Research Database (Denmark)

    Tufte, Thomas

    This user guide on participatory communication aims to answer the following questions: What do we mean when we say participatory communication? What are the practical implications of working with participatory communication strategies in development and social change processes? What practical......, tools, and experiences on how to implement participatory communications strategies. It is targeted toward government officials, World Bank staff, develompent workers in the field, and civil society....

  8. Wastewater treatment by sonophotocatalysis using PEG modified TiO2 film in a circular Photocatalytic-Ultrasonic system.

    Science.gov (United States)

    Hu, Xiaohong; Zhu, Qi; Gu, Zhibin; Zhang, Nan; Liu, Na; Stanislaus, Mishma S; Li, Dawei; Yang, Yingnan

    2017-05-01

    TiO2 photocatalyst film recently has been utilized as the potential candidate for the wastewater treatment, due to its high stability and low toxicity. In order to further increase the photocatalytic ability and stability, different molecular weight of polyethylene glycol (PEG) were used to modify TiO2 structure to synthesize porous thin film used in the developed Photocatalytic-Ultrasonic system in this work. The results showed that PEG2000 modified TiO2 calcinated under 450°C for 2h exhibited the highest photocatalytic activity, attributed to the smallest crystallite size and optimal particle size. Over 95.0% of rhodamine B (Rh B) was photocatalytically degraded by optimized PEG2000-TiO2 film after 60min of UV irradiation, while only about 50.8% of Rh B was decolored over pure TiO2 film. Furthermore, optimized PEG2000-TiO2 film was used in a circular Photocatalytic-Ultrasonic system, and the obtained synergy (0.6519) of sonophotocatalysis indicated its extremely high efficiency for Rh B degradation. In this Photocatalytic-Ultrasonic system, larger amount of PEG2000-TiO2 coated glass beads, stronger ultrasonic power and longer experimental time could result to higher degradation efficiency of Rh B. In addition, repetitive experiments showed that about 97.2% of Rh B were still degraded in the fifth experiment by sonophotocatalysis using PEG2000-TiO2 film. Therefore, PEG2000-TiO2 film used in Photocatalytic-Ultrasonic system has promising potential for wastewater treatment, due to its excellent photocatalytic activity and high stability.

  9. Pure Red Cell Aplasia Caused by Acute Hepatitis A

    OpenAIRE

    Lee, Tae Heon; Oh, Suk Joong; Hong, Soojung; Lee, Kyu Bek; Park, Hyosoon; Woo, Hee-Yeon

    2011-01-01

    Pure red cell aplasia is characterized as a normocytic anemia associated with reticulocytopenia and the absence of erythroblasts in the bone marrow. Pure red cell aplasia can be induced by various causes such as thymoma, connective tissue disease, viral infection, lymphoma, and adverse drug reactions. There have been only a few reports of pure red cell aplasia associated with acute viral hepatitis A. In Korea, no case of pure red cell aplasia caused by acute hepatitis A has yet been reported....

  10. Existential Communication.

    Science.gov (United States)

    Self, Charles C.

    Focusing on the seminal work "Being and Nothingness," this paper explores the implications of the ideas of Jean-Paul Sartre for the study of communication in society. The paper redefines communication from an existential point of view, explores some implications of this redefinition for the study of communication within the social…

  11. Existential Communication.

    Science.gov (United States)

    Self, Charles C.

    Focusing on the seminal work "Being and Nothingness," this paper explores the implications of the ideas of Jean-Paul Sartre for the study of communication in society. The paper redefines communication from an existential point of view, explores some implications of this redefinition for the study of communication within the social setting, and…

  12. Communication Links

    OpenAIRE

    2003-01-01

    This interactive tutorial helps learners to: Identify key upward, lateral, downward, and informal communication links in their organizations. , Reflect on the benefits, control, satisfaction, information filters, and feedback mechanism of various communication links in the organizations. OCL1000 Communicating Change in Complex Organizations

  13. Stereotypes Communication

    Science.gov (United States)

    Zhang, Shuli; Deng, Dongyuan

    2009-01-01

    We live in a world, which is becoming a Global Village in which information and communication attract people's attention more than ever before. Our desire to communicate with strangers and our relationships with them depend on the degree to which we are effective in communicating with them. There are so many factors restricting or improving…

  14. Existential Communication.

    Science.gov (United States)

    Self, Charles C.

    Focusing on the seminal work "Being and Nothingness," this paper explores the implications of the ideas of Jean-Paul Sartre for the study of communication in society. The paper redefines communication from an existential point of view, explores some implications of this redefinition for the study of communication within the social…

  15. Cultural Communications.

    Science.gov (United States)

    Armas, Jose

    It is too often taken for granted that the communication process with culturally different children takes place as readily as it might with children from Anglo cultures. Most teachers receive training in verbal and formal communication skills; children come to school with nonverbal and informal communication skills. This initially can create…

  16. Synthesis of Pure and Pt-Doped ZnO Particles Through Aerosol Route Using Nitrate and PDDA-Pt(IV) Complex Solution%利用浮质方法将硝酸盐和PDDA-Pt(IV)复合溶液合成纯净及Pt掺杂的ZnO颗粒

    Institute of Scientific and Technical Information of China (English)

    V.M.Djinovic; L.T.; Maneieb; G.A.; Bogdanovic; P.J.; Vulie; G.; del; Rosario; T.J.; Sabo; O.B.; Milosevie

    2005-01-01

    @@ Pure and Pt-doped ZnO nanophase particles were synthesized using the ultrasonic spray pyrolysis. Particles were obtained through decomposition of zincnitrate and new developed Pt(IV) complex with 1,3-propylenediamine-N,N'-diacetate ligand (pdda) belonging to the tetradentate class.

  17. Mice produce ultrasonic vocalizations by intra-laryngeal planar impinging jets

    DEFF Research Database (Denmark)

    Mahrt, Elena; Agarwal, Anurag; Perkel, David

    2016-01-01

    and experimental evidence for an alternative and novel vocal production mechanism: a glottal jet impinging onto the laryngeal inner planar wall. Our data provide a framework for future research on the neuromuscular control of mouse vocal production and for interpreting mouse vocal behavior phenotypes.......Rodent ultrasonic vocalizations (USVs) are a vital tool for linking gene mutations to behavior in mouse models of communication disorders, such as autism [1]. However, we currently lack an understanding of how physiological and physical mechanisms combine to generate acoustic features...

  18. On the relationships between ultrasonic calling and anxiety-related behavior in rats

    Energy Technology Data Exchange (ETDEWEB)

    Schwarting, R.K.W.; Wöhr, M. [Experimental and Physiological Psychology, Philipps-University of Marburg, Marburg (Germany)

    2012-03-23

    In the present review, the phenomenon of ultrasonic vocalization in rats will be outlined, including the three classes of vocalizations, namely 40-kHz calls of pups, and 22- and 50-kHz calls of juvenile and adult rats, their general relevance to behavioral neuroscience, and their special relevance to research on anxiety, fear, and defense mechanisms. Here, the emphasis will be placed on 40- and 22-kHz calls, since they are typical for various situations with aversive properties. Among other topics, we will discuss whether such behavioral signals can index a certain affective state, and how these signals can be used in social neuroscience, especially with respect to communication. Furthermore, we will address the phenomenon of inter-individual variability in ultrasonic calling and what we currently know about the mechanisms, which may determine such variability. Finally, we will address the current knowledge on the neural and pharmacological mechanisms underlying 22-kHz ultrasonic vocalization, which show a substantial overlap with mechanisms known from other research on fear and anxiety, such as those involving the periaqueductal gray or the amygdala.

  19. Hologram of a pure state black hole

    Science.gov (United States)

    Roy, Shubho R.; Sarkar, Debajyoti

    2015-12-01

    In this paper, we extend the Hamilton-Kabat-Lifschytz-Lowe (HKLL) holographic smearing function method to reconstruct (quasi)local anti-de Sitter bulk scalar observables in the background of a large anti-de Sitter black hole formed by null shell collapse (a "pure state" black hole), from the dual conformal field theory which is undergoing a sudden quench. In particular, we probe the near horizon and subhorizon bulk locality. First, we construct local bulk operators from the conformal field theory in the leading semiclassical limit, N →∞ . Then, we look at effects due to the finiteness of N , where we propose a suitable coarse-graining prescription involving early and late time cutoffs to define semiclassical bulk observables which are approximately local, their departure from locality being nonperturbatively small in N . Our results have important implications on the black hole information problem.

  20. Anomalous rectification in a purely electronic memristor

    Science.gov (United States)

    Wang, Jingrui; Pan, Ruobing; Cao, Hongtao; Wang, Yang; Liang, Lingyan; Zhang, Hongliang; Gao, Junhua; Zhuge, Fei

    2016-10-01

    An anomalous rectification was observed in a purely electronic memristive device Ti/ZnO/Pt. It could be due to (1) an Ohmic or quasi-Ohmic contact at the ZnO/Pt interface and (2) a Schottky contact at the Ti/ZnO interface. The Ohmic contact originates from the reduction of ZnO occurring in the whole film instead of only at the Ti/ZnO interface. The Schottky contact may come from moisture adsorbed in the nanoporous ZnO. The conduction in the electroformed device is controlled by the carrier trapping/detrapping of the trap sites, inducing a poor rectification and high nonlinearity. Furthermore, a complementary resistive switching was achieved.

  1. Momentum of the Pure Radiation Field

    Directory of Open Access Journals (Sweden)

    Lehnert B.

    2007-01-01

    Full Text Available The local momentum equation of the pure radiation field is considered in terms of an earlier elaborated and revised electromagnetic theory. In this equation the contribution from the volume force is found to vanish in rectangular geometry, and to become nonzero but negligible in cylindrical geometry. Consequently the radiated momentum is due to the Poynting vector only, as in conventional electrodynamics. It results in physically relevant properties of a photon model having an angular momentum (spin. The Poynting vector concept is further compared to the quantized momentum concept for a free particle, as represented by a spatial gradient operator acting on the wave function. However, this latter otherwise successful concept leads to difficulties in the physical interpretation of known and expected photon properties such as the spin, the negligible loss of transverse momentum across a bounding surface, and the Lorentz invariance.

  2. Evolving spacetimes with purely radial tension

    Directory of Open Access Journals (Sweden)

    B. Nasre Esfahani

    2000-12-01

    Full Text Available   In this study time-dependent and spherically symmetric solutions of the Einstein field equations in an anisotropic background with a purely radial tension are presented. There exist three classes of solutions,1 An open spacetime with a wormhole at its center. 2 A conical spacetime. 3 A closed spacetime. These inhomogeneous solutions are reduced to FRW spacetimes in matter-dominated era, asymptotically. Therefore, they can be used to describe local inhomogeneities that are not considered in the standard model. For the wormhole solution. it is explicity shown that the considered matter is non-exotic, that is, it does not violate the energy conditions. Also, static solutions are studied. There is only one static solution,a conical spacetime. In this case, the matter satisfies the energy condition critically.

  3. Pure White Cell Aplasia and Necrotizing Myositis

    Directory of Open Access Journals (Sweden)

    Peter Geon Kim

    2016-01-01

    Full Text Available Pure white cell aplasia (PWCA is a rare hematologic disorder characterized by the absence of neutrophil lineages in the bone marrow with intact megakaryopoiesis and erythropoiesis. PWCA has been associated with autoimmune, drug-induced, and viral exposures. Here, we report a case of a 74-year-old female who presented with severe proximal weakness without pain and was found to have PWCA with nonspecific inflammatory necrotizing myositis and acute liver injury on biopsies. These findings were associated with a recent course of azithromycin and her daily use of a statin. Myositis improved on prednisone but PWCA persisted. With intravenous immunoglobulin and granulocyte-colony stimulating factor therapies, her symptoms and neutrophil counts improved and were sustained for months.

  4. Fock expansion of multimode pure Gaussian states

    Energy Technology Data Exchange (ETDEWEB)

    Cariolaro, Gianfranco; Pierobon, Gianfranco, E-mail: gianfranco.pierobon@unipd.it [Università di Padova, Padova (Italy)

    2015-12-15

    The Fock expansion of multimode pure Gaussian states is derived starting from their representation as displaced and squeezed multimode vacuum states. The approach is new and appears to be simpler and more general than previous ones starting from the phase-space representation given by the characteristic or Wigner function. Fock expansion is performed in terms of easily evaluable two-variable Hermite–Kampé de Fériet polynomials. A relatively simple and compact expression for the joint statistical distribution of the photon numbers in the different modes is obtained. In particular, this result enables one to give a simple characterization of separable and entangled states, as shown for two-mode and three-mode Gaussian states.

  5. Hologram of a pure state black hole

    CERN Document Server

    Roy, Shubho R

    2015-01-01

    In this paper we extend the HKLL holographic smearing function method to reconstruct (quasi)local AdS bulk scalar observables in the background of a large AdS black hole formed by null shell collapse (a "pure state" black hole), from the dual CFT which is undergoing a sudden quench. In particular, we probe the near horizon and sub-horizon bulk locality. First we construct local bulk operators from the CFT in the leading semiclassical limit, $N\\rightarrow\\infty$. Then we look at effects due to the finiteness of $N$, where we propose a suitable coarse-graining prescription involving early and late time cut-offs to define semiclassical bulk observables which are approximately local; their departure from locality being non-perturbatively small in $N$. Our results have important implications on the black hole information problem.

  6. Purely antiferromagnetic magnetoelectric random access memory

    Science.gov (United States)

    Kosub, Tobias; Kopte, Martin; Hühne, Ruben; Appel, Patrick; Shields, Brendan; Maletinsky, Patrick; Hübner, René; Liedke, Maciej Oskar; Fassbender, Jürgen; Schmidt, Oliver G.; Makarov, Denys

    2017-01-01

    Magnetic random access memory schemes employing magnetoelectric coupling to write binary information promise outstanding energy efficiency. We propose and demonstrate a purely antiferromagnetic magnetoelectric random access memory (AF-MERAM) that offers a remarkable 50-fold reduction of the writing threshold compared with ferromagnet-based counterparts, is robust against magnetic disturbances and exhibits no ferromagnetic hysteresis losses. Using the magnetoelectric antiferromagnet Cr2O3, we demonstrate reliable isothermal switching via gate voltage pulses and all-electric readout at room temperature. As no ferromagnetic component is present in the system, the writing magnetic field does not need to be pulsed for readout, allowing permanent magnets to be used. Based on our prototypes, we construct a comprehensive model of the magnetoelectric selection mechanisms in thin films of magnetoelectric antiferromagnets, revealing misfit induced ferrimagnetism as an important factor. Beyond memory applications, the AF-MERAM concept introduces a general all-electric interface for antiferromagnets and should find wide applicability in antiferromagnetic spintronics.

  7. Synaptic devices based on purely electronic memristors

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Ruobing [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Institute of Materials Science, School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Li, Jun; Zhuge, Fei, E-mail: zhugefei@nimte.ac.cn, E-mail: h-cao@nimte.ac.cn; Zhu, Liqiang; Liang, Lingyan; Zhang, Hongliang; Gao, Junhua; Cao, Hongtao, E-mail: zhugefei@nimte.ac.cn, E-mail: h-cao@nimte.ac.cn; Fu, Bing; Li, Kang [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)

    2016-01-04

    Memristive devices have been widely employed to emulate biological synaptic behavior. In these cases, the memristive switching generally originates from electrical field induced ion migration or Joule heating induced phase change. In this letter, the Ti/ZnO/Pt structure was found to show memristive switching ascribed to a carrier trapping/detrapping of the trap sites (e.g., oxygen vacancies or zinc interstitials) in ZnO. The carrier trapping/detrapping level can be controllably adjusted by regulating the current compliance level or voltage amplitude. Multi-level conductance states can, therefore, be realized in such memristive device. The spike-timing-dependent plasticity, an important Hebbian learning rule, has been implemented in this type of synaptic device. Compared with filamentary-type memristive devices, purely electronic memristors have potential to reduce their energy consumption and work more stably and reliably, since no structural distortion occurs.

  8. Bipedal nanowalker by pure physical mechanisms

    CERN Document Server

    Cheng, Juan; Hou, Ruizheng; Efremov, Artem; Liu, Ruchuan; van der Maarel, Johan RC; Wang, Zhisong

    2013-01-01

    Artificial nanowalkers are inspired by biomolecular counterparts from living cells, but remain far from comparable to the latter in design principles. The walkers reported to date mostly rely on chemical mechanisms to gain a direction; they all produce chemical wastes. Here we report a light-powered DNA bipedal walker based on a design principle derived from cellular walkers. The walker has two identical feet and the track has equal binding sites; yet the walker gains a direction by pure physical mechanisms that autonomously amplify an intra-site asymmetry into a ratchet effect. The nanowalker is free of any chemical waste. It has a distinct thermodynamic feature that it possesses the same equilibrium before and after operation, but generates a truly non-equilibrium distribution during operation. The demonstrated design principle exploits mechanical effects and is adaptable for use in other nanomachines.

  9. Biological warfare warriors, secrecy and pure science in the Cold War: how to understand dialogue and the classifications of science.

    Science.gov (United States)

    Bud, Robert

    2014-01-01

    This paper uses a case study from the Cold War to reflect on the meaning at the time of the term 'Pure Science'. In 1961, four senior scientists from Britain's biological warfare centre at Porton Down visited Moscow both attending an International Congress and visiting Russian microbiological and biochemical laboratories. The reports of the British scientists in talking about a limited range of topics encountered in the Soviet Union expressed qualities of openness, sociologists of the time associated with pure science. The paper reflects on the discourses of "Pure Science", secrecy and security in the Cold War. Using Bakhtin's approach, I suggest the cordial communication between scientists from opposing sides can be seen in terms of the performance, or speaking, of one language among several at their disposal. Pure science was the language they were allowed to share outside their institutions, and indeed political blocs.

  10. 7 CFR 201.64 - Pure live seed.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Pure live seed. 201.64 Section 201.64 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Tolerances § 201.64 Pure live seed. The tolerance for pure live seed shall be determined...

  11. Tractable Quantification of Entanglement for Multipartite Pure States

    Institute of Scientific and Technical Information of China (English)

    JIANG Nian-Quan; WANG Yu-Jian; ZHENG Yi-Zhuang; CAI Gen-Chang

    2008-01-01

    We present kth-order entanglement measure and global kth-order entanglement measure for multipartite pure states, and extend Bennett's measure of partial entropy for bipartite pure states to a multipartite case. These measures are computable and can effectively classify and quantify the entanglement of multipartite pure states.

  12. Social cognition in "pure" delusional disorder.

    Science.gov (United States)

    Bömmer, Isabel; Brüne, Martin

    2006-09-01

    Introduction. Delusional disorders are characterised by monothematic, "encapsulated" and incorrigible false beliefs and misinterpretations of social signals. Due to the rarity of cases with "pure" delusional disorder (DD) in clinical settings most studies of social cognition in delusional patients have focused on patients with paranoid schizophrenia. In the present study we sought to examine emotion recognition, theory of mind abilities, and pragmatic language comprehension in patients with delusional disorder. Methods. Social cognition was assessed in 21 patients recruited over a 3-year period who were diagnosed with delusional disorder, paranoid, erotomanic, or jealous type. In addition to an emotion recognition and theory of mind test battery, we included a novel German Proverb Test, which has been found indicative of subtle theory of mind deficits in schizophrenic patients. Executive functioning was assessed using the Wisconsin Card Sorting Test (WCST). Psychopathology was measured using the Positive and Negative Symptoms Scale (PANSS). Patients' task performance was compared to a group of 22 healthy control persons paralleled for verbal intelligence, education, and age. Results. Patients with DD made significantly more perseverative errors in the WCST, they performed more poorly on the theory of mind tasks and the proverb test, but were unimpaired in basic emotion recognition abilities relative to controls. When executive functioning was co-varied out, the group differences in theory of mind disappeared, whereas the greater propensity of patients with DD to interpret proverbs literally remained significant. Conclusions. In "pure" DD the basic social cognitive abilities appear to be preserved. Difficulties in metaphorical speech comprehension and executive functioning could, however, indicate more subtle social cognitive deficits in these patients.

  13. Hole transport in pure and doped hematite

    Science.gov (United States)

    Liao, Peilin; Carter, Emily A.

    2012-07-01

    Hematite (α-Fe2O3) is a promising candidate for use in photovoltaic (PV) and photoelectrochemical devices. Its poor conductivity is one major drawback. Doping hematite either p-type or n-type greatly enhances its measured conductivity and is required for potential p-n junctions in PVs. Here, we study hole transport in pure and doped hematite using an electrostatically embedded cluster model with ab initio quantum mechanics (unrestricted Hartree-Fock theory). Consistent with previous work, the model suggests that hole hopping is via oxygen anions for pure hematite. The activation energy for hole mobility is predicted to be at least 0.1 eV higher than the activation energy for electron mobility, consistent with the trend observed in experiments. We examine four dopants—magnesium(II), nickel(II), copper(II), and manganese(II/III) in direct cation substitution sites—to gain insight into the mechanism by which conductivity is improved. The activation energies are used to assess qualitative effects of different dopants. The hole carriers are predicted to be attracted to O anions near the dopants. The magnitude of the trapping effect is similar among the four dopants in their +2 oxidation states. The multivalent character of Mn doping facilitates local hole transport around Mn centers via a low-barrier O-Mn-O pathway, which suggests that higher hole mobility can be achieved with increasing Mn doping concentration, especially when a network of these low-barrier pathways is produced. Our results suggest that the experimentally observed conductivity increase in Mg-, Ni-, and Cu-doped p-type hematite is mostly due to an increase in hole carriers rather than improved mobility, and that Mg-, Ni-, and Cu-doping perform similarly, while the conductivity of Mn-doped hematite might be significantly improved in the high doping concentration limit.

  14. Production of pure hydrogen by ethanol dehydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Santacesaria, E.; Carotenuto, G.; Tesser, R.; Di Serio, M. [Naples ' ' Federico II' ' Univ. (Italy). Dept. of Chemistry

    2010-12-30

    Hydrogen production from bio-ethanol is one of the most promising renewable processes to generate electricity using fuel cells. In this work, we have studied the production of pure hydrogen as by product of ethanol dehydrogenation reaction. This reaction is promoted by copper based catalysts and according to the catalyst used and the operative conditions gives place to acetaldehyde or ethyl acetate as main products. We studied in particular the performance of a commercial copper/copper chromite catalyst, supported on alumina and containing barium chromate as promoter that has given the best results. By operating at low pressure and temperature with short residence times, acetaldehyde is more selectively produced, while, by increasing the pressure (10-30 bars), the temperature (200-260 C) and the residence time (about 100 (grams hour/mol) of ethanol contact time) the selectivity is shifted to the production of ethyl acetate. However, in both cases pure hydrogen is obtained, as by product, that can easily be separated. Hydrogen obtained in this way is exempt of CO and can be directly fed to fuel cells without any inconvenience. In this work, runs performed in different operative conditions have been reported with the scope to individuate the best conditions. A carrier of H{sub 2} 6% in N{sub 2} has been used. The studied catalyst has also shown a good thermal stability with respect to sintering phenomena, that generally occurs during the dehydrogenation on other copper catalysts. Hydrogen productivities of 8-39 mol{sub H2} (gcat){sup -1}(h){sup -1} have been obtained for the explored temperature range 200-260 C. At last, the most accredited reaction mechanism is reported and discussed on the basis of the obtained results. (orig.)

  15. Explicit receivers for pure-interference bosonic multiple access channels

    CERN Document Server

    Wilde, Mark M

    2012-01-01

    The pure-interference bosonic multiple access channel has two senders and one receiver, such that the senders each communicate with a single mode of light and the effect of the channel is to mix their transmissions on a beamsplitter. The receiver then obtains a signal from one of the output ports. In prior work, Yen and Shapiro found the capacity region of this channel if the senders are restricted to coherent-state encodings. Here, we demonstrate how to achieve the Yen-Shapiro region (in some cases) with a sequential decoding strategy, such that the receiver performs binary-outcome quantum measurements for every codeword pair in the senders' codebooks. A crucial component of this scheme is a non-destructive "vacuum-or-not" measurement that projects an n-symbol modulated codeword onto the n-fold vacuum state or its orthogonal complement, such that the post-measurement state is either the n-fold vacuum or has the vacuum removed from the support of the n symbols' joint quantum state. This receiver requires the ...

  16. Communication Acoustics

    DEFF Research Database (Denmark)

    Blauert, Jens

    Communication Acoustics deals with the fundamentals of those areas of acoustics which are related to modern communication technologies. Due to the advent of digital signal processing and recording in acoustics, these areas have enjoyed an enormous upswing during the last 4 decades. The book...... the book a source of valuable information for those who want to improve or refresh their knowledge in the field of communication acoustics - and to work their way deeper into it. Due to its interdisciplinary character Communication Acoustics is bound to attract readers from many different areas, such as......: acoustics, cognitive science, speech science, and communication technology....

  17. Yeast Cell Trapping In Ultrasonic Wave Field Using Ultrasonic Contrast Agent

    Science.gov (United States)

    Yamakoshi, Yoshiki; Koitabashi, Yusuke; Nakajima, Naritsugu; Miwa, Takashi

    2006-05-01

    Microobject manipulation using ultrasonic waves is expected to play important roles in constructing future drug or gene delivery systems. The acoustic radiation force, which is applied to microobjects, traps the objects at the desired position. A microjet, which is produced by bubble explosion under high-intensity ultrasonic waves, creates microholes through the cell membrane (sonoporation), which is considered as a sophisticated method of improving the doses of drugs or genes injected into a tissue. Aiming at increasing the trapping force in micro bubble manipulation using ultrasonic waves, we have proposed a novel method based on the self-organization of microbubbles. This method uses seed bubbles in order to trap the target bubbles. In this study, the proposed method is applied to yeast cell trapping using ultrasonic waves. An ultrasonic wave contrast agent (Levovist; Shering A.G., Germany) is used as a seed bubble. It is shown that the number of trapped yeast cells depends on the preparation of the yeast cells. In order to evaluate the result, two additional experiments are carried out by changing the internal gas of the seed bubbles and by using bubbles with a polymer shell.

  18. Lipid releasing characteristics of microalgae species through continuous ultrasonication.

    Science.gov (United States)

    Natarajan, Ramya; Ang, Wei Ming Russell; Chen, Xue; Voigtmann, Michael; Lau, Raymond

    2014-04-01

    In this study, the lipid releasing characteristics of several microalgae species through continuous ultrasonication was examined. Two marine microalgae species, Tetraselmis suecica and Nannochloropsis sp., and one freshwater species, Chlorella sp. were ultrasonicated directly after cultivation. The cell disruption efficiency and lipids releasing pattern from microalgae cells were measured under various ultrasonication conditions. It was found that cell disruption efficiency correlates well with ultrasonication energy consumption despite the ultrasonication conditions. Lipids in Chlorella sp. that has rigid cell walls were released to the aqueous phase after cell disruption. T. suecica and Nannochloropsis sp. that have flexible cell membranes tend to coil up and retain the membrane lipids after disruption. Continuous ultrasonication can be a potential method to release the lipids in rigid walled microalgae species without expensive dewatering steps.

  19. Analysis and Management System of Digital Ultrasonic Image

    Institute of Scientific and Technical Information of China (English)

    TAO Qiang; ZHANG Hai-yan; LI Xia; WANG Ke

    2008-01-01

    This paper presents the analysis and management system of digital ultrasonic image. The system can manage medical ultrasonic image by collecting, saving and transferring, and realize that section offices of ultrasonic image in hospital network manage. The system use network technology in transferring image between ultrasonic equipments to share patient data in ultrasonic equipments. And doctors can input patient diagnostic report,saved by text file and case history, digitally managed. The system can be realized by Visual C++ which make windows applied. The system can be brought forward because PACS prevail with various hospitals,but PACS is expensive. In view of this status, we put forward to the analysis and management system of digital ultrasonic image,which is similar to PACS.

  20. A novel approach for the synthesis of superparamagnetic Mn3O4 nanocrystals by ultrasonic bath.

    Science.gov (United States)

    Rohani Bastami, T; Entezari, M H

    2012-05-01

    In this study, the synthesis of Mn(3)O(4) (husmannite) nanoparticles was carried out in two different alkali media under sonication by ultrasonic bath and conventional method. Manganese acetate was used as precursor, sodium hydroxide and hexamethylenetetramine (HMT) as basic reagents in this synthesis. An ultrasonic bath with low intensity was used for the preparation of nanomaterials. The as prepared samples were characterized with X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (HRTEM, TEM), energy-dispersive spectrum (EDS), and superconducting quantum interference device (SQUID) analysis. The XRD patterns exhibit the nanocrystals are in pure tetragonal phase. The chemical composition was obtained by EDS analysis and confirmed the presence of Mn and O in the sample. According to the TEM and HRTEM results, both nanorods and nanoparticles of Mn(3)O(4) were obtained in the presence of ultrasonic irradiation. The average size of nanoparticles was 10nm, and the size of nanorods was 12 nm in diameter and 100-900 nm in length for the samples prepared in basic medium with sodium hydroxide. In the conventional method with the same basic medium, the nanorod was not observed and the nearly cubic nanoparticles was appeared with an average size of 2.5 nm. The selected area electron diffraction (SAED) patterns revealed that the nanocrystals are polycrystalline in nature. When HMT was used as a basic reagent in the presence of ultrasonic irradiation, it was led to a higher size of nanoparticles and nanorods than when sodium hydroxide was used as a basic reagent. The average size of nanoparticles was about 15 nm and its shape was nearly cubic. The diameter for nanorods was 50 nm and the length was about a few micrometers. The magnetic measurements were carried out on the sample prepared in sodium hydroxide under ultrasonic irradiation. These measurements as a function of temperature and field strength showed a reduction

  1. Effect of the Substrate Movement on the Optical Properties of ZnO Thin Films Deposited by Ultrasonic Spray Pyrolysis

    OpenAIRE

    2012-01-01

    Using a modified ultrasonic spray pyrolysis (USP) system, ZnO thin films were deposited on the substrate moved back and forth (ZO1) and rotated (ZO3) as well as fixed (ZO2) in the conventional USP technique. Prepared thin films are pure ZnO with a preferred crystalline orientation of (0 0 2) in the hexagonal wurtzite structure. Diffraction angle shift implies a decrease lattice parameter along c-axis and a-axis 0.2% and 0.3%, respectively. Maximum strain has been found for ZO1 which is about ...

  2. Ultrasonic Real-Time Quality Monitoring Of Aluminum Spot Weld Process

    Science.gov (United States)

    Perez Regalado, Waldo Josue

    The real-time ultrasonic spot weld monitoring system, introduced by our research group, has been designed for the unsupervised quality characterization of the spot welding process. It comprises the ultrasonic transducer (probe) built into one of the welding electrodes and an electronics hardware unit which gathers information from the transducer, performs real-time weld quality characterization and communicates with the robot programmable logic controller (PLC). The system has been fully developed for the inspection of spot welds manufactured in steel alloys, and has been mainly applied in the automotive industry. In recent years, a variety of materials have been introduced to the automotive industry. These include high strength steels, magnesium alloys, and aluminum alloys. Aluminum alloys have been of particular interest due to their high strength-to-weight ratio. Resistance spot welding requirements for aluminum vary greatly from those of steel. Additionally, the oxide film formed on the aluminum surface increases the heat generation between the copper electrodes and the aluminum plates leading to accelerated electrode deterioration. Preliminary studies showed that the real-time quality inspection system was not able to monitor spot welds manufactured with aluminum. The extensive experimental research, finite element modelling of the aluminum welding process and finite difference modeling of the acoustic wave propagation through the aluminum spot welds presented in this dissertation, revealed that the thermodynamics and hence the acoustic wave propagation through an aluminum and a steel spot weld differ significantly. For this reason, the hardware requirements and the algorithms developed to determine the welds quality from the ultrasonic data used on steel, no longer apply on aluminum spot welds. After updating the system and designing the required algorithms, parameters such as liquid nugget penetration and nugget diameter were available in the ultrasonic data

  3. Ultrasonic wave interactions with magnetic colloids

    CERN Document Server

    Chapman, J R

    2001-01-01

    fluids have been performed in an effort to determine the relative stability of the fluids. The experimental results have been compared with a combined scattering and hydrodynamic model (Allegra and Hawley 1972) and the ultrasonic anisotropy theory of Skumiel (1997). An on-line quality assurance process is proposed. Originally invented as a method for moving spacecraft fuel in weightless conditions, magnetic colloids or ferrofluids are now used in applications as diverse as the dissipation of heat in the voice coils of a loudspeaker, and for the separation of scrap metal. It has been found that aqueous ferrofluids become unstable after a period of time and with dilution. Therefore, there is a need to characterize the colloidal fluid to study the effects of degradation. Additionally, due to the high cost of ferrofluids and the large volumes required for some applications, the fluid is recycled. It is therefore necessary to develop a system for quality assurance for the fluid reclamation process. Ultrasonic meth...

  4. Ultrasonically encoded photoacoustic flowgraphy in biological tissue

    Science.gov (United States)

    Wang, Lidai; Xia, Jun; Yao, Junjie; Maslov, Konstantin I.; Wang, Lihong V.

    2014-01-01

    Blood flow speed is an important functional parameter. Doppler ultrasound flowmetry lacks sufficient sensitivity to slow blood flow (several to tens of millimeters per second) in deep tissue. To address this challenge, we developed ultrasonically encoded photoacoustic flowgraphy combining ultrasonic thermal tagging with photoacoustic imaging. Focused ultrasound generates a confined heat source in acoustically absorptive fluid. Thermal waves propagate with the flow and are directly visualized in pseudo color using photoacoustic computed tomography. The Doppler shift is employed to calculate the flow speed. This method requires only acoustic and optical absorption, and thus is applicable to continuous fluid. A blood flow speed as low as 0.24 mm·s−1 was successfully measured. Deep blood flow imaging was experimentally demonstrated under 5-mm-thick chicken breast tissue. PMID:24289689

  5. Ultrasonic characterization of single drops of liquids

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, Dipen N. (Los Alamos, NM)

    1998-01-01

    Ultrasonic characterization of single drops of liquids. The present invention includes the use of two closely spaced transducers, or one transducer and a closely spaced reflector plate, to form an interferometer suitable for ultrasonic characterization of droplet-size and smaller samples without the need for a container. The droplet is held between the interferometer elements, whose distance apart may be adjusted, by surface tension. The surfaces of the interferometer elements may be readily cleansed by a stream of solvent followed by purified air when it is desired to change samples. A single drop of liquid is sufficient for high-quality measurement. Examples of samples which may be investigated using the apparatus and method of the present invention include biological specimens (tear drops; blood and other body fluid samples; samples from tumors, tissues, and organs; secretions from tissues and organs; snake and bee venom, etc.) for diagnostic evaluation, samples in forensic investigations, and detection of drugs in small quantities.

  6. Lamb Wave Multi-touch Ultrasonic Touchscreen.

    Science.gov (United States)

    Firouzi, Kamyar; Nikoozadeh, Amin; Carver, Thomas; Khuri-Yakub, Butrus

    2016-09-13

    Touchscreen sensors are widely used in many devices such as smart phones, tablets, laptops, etc., with diverse applications. We present the design, analysis, and implementation of an ultrasonic touchscreen system that utilizes interaction of transient Lamb waves with objects in contact with the screen. It attempts to improve on the existing ultrasound technologies, with the potential of addressing some of the weaknesses of the dominant technologies, such as the capacitive or resistive ones. Compared to the existing ultrasonic and acoustic modalities, among other advantages, it provides the capability of detecting several simultaneous touch points, and also a more robust performance. The localization algorithm, given the hardware design, can detect several touch points with a very limited number of measurements (one or two). This in turn can significantly reduce the manufacturing cost.

  7. Automatic feed system for ultrasonic machining

    Science.gov (United States)

    Calkins, Noel C.

    1994-01-01

    Method and apparatus for ultrasonic machining in which feeding of a tool assembly holding a machining tool toward a workpiece is accomplished automatically. In ultrasonic machining, a tool located just above a workpiece and vibrating in a vertical direction imparts vertical movement to particles of abrasive material which then remove material from the workpiece. The tool does not contact the workpiece. Apparatus for moving the tool assembly vertically is provided such that it operates with a relatively small amount of friction. Adjustable counterbalance means is provided which allows the tool to be immobilized in its vertical travel. A downward force, termed overbalance force, is applied to the tool assembly. The overbalance force causes the tool to move toward the workpiece as material is removed from the workpiece.

  8. Ultrasonic vibrating system design and tool analysis

    Institute of Scientific and Technical Information of China (English)

    Kei-Lin KUO

    2009-01-01

    The applications of ultrasonic vibrations for material removal processes exist predominantly in the area of vertical processing of hard and brittle materials. This is because the power generated by vertical vibrating oscillators generates the greatest direct penetration, in order to conduct material removal on workpieces by grains. However, for milling processes, vertical vibrating power has to be transformed into lateral (horizontal) vibration to produce the required horizontal cutting force. The objective of this study is to make use of ultrasonic lateral transformation theory to optimize processing efficiency, through the use of the finite element method for design and analysis of the milling tool. In addition, changes can be made to the existing vibrating system to generate best performance under consistent conditions, namely, using the same piezoelectric ceramics.

  9. Ultrasonic nondestructive evaluation systems industrial application issues

    CERN Document Server

    Callegari, Sergio; Montisci, Augusto; Ricci, Marco; Versaci, Mario

    2015-01-01

    This book covers the practical implementation of ultrasonic NDT techniques in an industrial environment, discussing several issues that may emerge and proposing strategies for addressing them successfully.  It aims to bridge advanced academic research results and their application to industrial procedures. The topics covered in the text range from the basic operation of an ultrasonic NDT system to the simulation of the measurement operations; from the choice and generation of the signals energizing the system to the different ways of exploiting the probes and their output signals; and from quality assessment evaluation to the use of soft computing techniques for classification. Throughout the text, an effort is made to embrace a system view where the physical and technological aspects of sensing are addressed together with higher abstraction levels, such as signal and information processing. Consequently, the book aims at guiding the reader through the various tasks requested for developing a complete ultras...

  10. High resolution in situ ultrasonic corrosion monitor

    Science.gov (United States)

    Grossman, R.J.

    1984-01-10

    An ultrasonic corrosion monitor is provided which produces an in situ measurement of the amount of corrosion of a monitoring zone or zones of an elongate probe placed in the corrosive environment. A monitoring zone is preferably formed between the end of the probe and the junction of the zone with a lead-in portion of the probe. Ultrasonic pulses are applied to the probe and a determination made of the time interval between pulses reflected from the end of the probe and the junction referred to, both when the probe is uncorroded and while it is corroding. Corresponding electrical signals are produced and a value for the normalized transit time delay derived from these time interval measurements is used to calculate the amount of corrosion.

  11. Ultrasonic-aided fabrication of gold nanofluids.

    Science.gov (United States)

    Chen, Hui-Jiuan; Wen, Dongsheng

    2011-03-07

    A novel ultrasonic-aided one-step method for the fabrication of gold nanofluids is proposed in this study. Both spherical- and plate-shaped gold nanoparticles (GNPs) in the size range of 10-300 nm are synthesized. Subsequent purification produces well-controlled nanofluids with known solid and liquid contents. The morphology and properties of the nanoparticle and nanofluids are characterized by transmission electron microscopy, scanning electron microscope, energy dispersive X-ray spectroscope, X-ray diffraction spectroscopy, and dynamic light scattering, as well as effective thermal conductivities. The ultrasonication technique is found to be a very powerful tool in engineering the size and shape of GNPs. Subsequent property measurement shows that both particle size and particle shape play significant roles in determining the effective thermal conductivity. A large increase in effective thermal conductivity can be achieved (approximately 65%) for gold nanofluids using plate-shaped particles under low particle concentrations (i.e.764 μM/L).

  12. An ultrasonic plethysmograph for space flight applications

    Science.gov (United States)

    Bhagat, P. K.; Lafferty, J. F.; Bowman, D.; Kadaba, M. P.

    1980-01-01

    The development of an ultrasonic plethysmograph based on the transit time measurement principle is reported, which meets the space-imposed requirements for evaluating cardiovascular deconditioning. It consists of a pulse generator, pulse receiver amplifier, voltage comparator, synchronous pulse generator, elapsed time counter, and transmit and receive piezoelectric crystals resonant at 2 MHz and of 3 mm diameter. The transit time for an ultrasonic pulse to propagate across a limb cross section is computed in a digital fashion using a 32 MHz clock, and resolution is 0.049 mm with the range being approximately 200 mm. Experimental results regarding dynamic system response were found comparable in both accuracy and sensitivity to those of a Whitney strain gage using a 50 torr venous occlusion.

  13. Ultrasonic Characterization of Interfaces in Composite Bonds

    Science.gov (United States)

    Wang, N.; Lobkis, O. I.; Rokhlin, S. I.; Cantrell, J. H.

    2010-01-01

    The inverse determination of imperfect interfaces from reflection spectra of normal and oblique incident ultrasonic waves in adhesive bonds of multidirectional composites is investigated. The oblique measurements are complicated by the highly dispersed nature of oblique wave spectra at frequencies above 3MHz. Different strategies for bond property reconstruction, including a modulation method, are discussed. The relation of measured interfacial spring density to the physico-chemical model of a composite interface described by polymer molecular bonds to emulate loss of molecular strength on an adhesive composite interface is discussed. This potentially relates the interfacial (adhesion) strength (number of bonds at the adhesive substrate interface) to the spring constant (stiffness) area density (flux), which is an ultrasonically measurable parameter.

  14. Ultrasonically encoded photoacoustic flowgraphy in biological tissue.

    Science.gov (United States)

    Wang, Lidai; Xia, Jun; Yao, Junjie; Maslov, Konstantin I; Wang, Lihong V

    2013-11-15

    Blood flow speed is an important functional parameter. Doppler ultrasound flowmetry lacks sufficient sensitivity to slow blood flow (several to tens of millimeters per second) in deep tissue. To address this challenge, we developed ultrasonically encoded photoacoustic flowgraphy combining ultrasonic thermal tagging with photoacoustic imaging. Focused ultrasound generates a confined heat source in acoustically absorptive fluid. Thermal waves propagate with the flow and are directly visualized in pseudo color using photoacoustic computed tomography. The Doppler shift is employed to calculate the flow speed. This method requires only acoustic and optical absorption, and thus is applicable to continuous fluid. A blood flow speed as low as 0.24  mm·s(-1)} was successfully measured. Deep blood flow imaging was experimentally demonstrated under 5-mm-thick chicken breast tissue.

  15. Piezoelectric single crystals for ultrasonic transducers in biomedical applications

    OpenAIRE

    Zhou, Qifa; Lam, Kwok Ho; Zheng, Hairong; Qiu, Weibao; Shung, K. Kirk

    2014-01-01

    Piezoelectric single crystals, which have excellent piezoelectric properties, have extensively been employed for various sensors and actuators applications. In this paper, the state–of–art in piezoelectric single crystals for ultrasonic transducer applications is reviewed. Firstly, the basic principles and design considerations of piezoelectric ultrasonic transducers will be addressed. Then, the popular piezoelectric single crystals used for ultrasonic transducer applications, including LiNbO...

  16. Ultrasonic distance sensors-An overview and trends

    Institute of Scientific and Technical Information of China (English)

    Bernd Henning; Andreas Schr(o)der

    2011-01-01

    Nowadays ultrasonic distance sensors are widely used in automobiles,robotics and in industrial automation.Some functional principles of usable transducers for airborne ultrasonic distance measurements are shown.As every sensor principle,ultrasonic distance sensors have pros and cons which lead to some problems and challenges described below.For the main challenges (crosstalk and blind zone) some trends and solutions are presented.

  17. Ultrasonic elastography in clinical quantitative assessment of fatty liver

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    AIM: To investigate the clinical application of ultrasonic elastography in quantitative assessment of fatty liver grading. METHODS: A total of 105 patients with fatty liver were divided into mild group (n = 46), moderate group (n = 39), and severe group (n = 20). Forty-five healthy individuals served as a normal control group. All patients who underwent routine ultrasound scan and further ultrasonic elastography were evaluated accordingly to the evaluation standards for ultrasonic elastography. The ratio of...

  18. Research on Ultrasonic NDT System for Complex Surface Parts

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Aimed at inner quality controlling for complex surface parts, an ultrasonic testing system for complex surface parts has been developed using ultrasonic NDT(Non-destructive Testing)which has features of strong penetration, well direction, high sensitivity, low cost, and harmless to people and material. The technologies of the computer, NC (Numerical control), precision mechanism, signal analysis and processing were integrated in the testing system. The system includes a PC, system software, ultrasonic data ...

  19. Ozonation with ultrasonic enhancement of p-nitrophenol wastewater

    Institute of Scientific and Technical Information of China (English)

    XU Xian-wen; SHI Hui-xiang; WANG Da-hui

    2005-01-01

    Synergetic effects for p-nitrophenol degradation were observed in the ozonation with ultrasonic enhancement. The enhancements of removal rate for p-nitrophenol and TOC were around 116% and 294% respectively in comparison with the individual ultrasound and ozonation systems. The synergetic phenomenon is attributed to two physicochemical mechanisms: (1)Ultrasound decomposes ozone causing augmentation of the activity of free radicals; (2) Ultrasonic wave increased the concentration of O3 in solution because of ultrasonic dispersion.

  20. Ultrasonication and food technology: A review

    OpenAIRE

    Ishrat Majid; Gulzar Ahmad Nayik; Vikas Nanda

    2015-01-01

    With increasing consumers demand and tightening of food and environmental regulations, traditional food-processing techniques have lost their optimum performance which gave rise to new and powerful technologies. Ultrasonic is a one of the fast, versatile, emerging, and promising non-destructive green technology used in the food industry from last few years. The ultrasound is being carried out in various areas of food technology namely crystallization, freezing, bleaching, degassing, extractio...

  1. Capacitor discharges, magnetohydrodynamics, X-rays, ultrasonics

    CERN Document Server

    Früngel, Frank B A

    1965-01-01

    High Speed Pulse Technology, Volume 1: Capacitor Discharges - Magnetohydrodynamics - X-Rays - Ultrasonics deals with the theoretical and engineering problems that arise in the capacitor discharge technique.This book discusses the characteristics of dielectric material, symmetrical switch tubes with mercury filling, and compensation conductor forms. The transformed discharge for highest current peaks, ignition transformer for internal combustion engines, and X-ray irradiation of subjects in mechanical motion are also elaborated. This text likewise covers the transformed capacitor discharge in w

  2. Perform Ultrasonic Testing on Cs Capsule Overpacks

    Energy Technology Data Exchange (ETDEWEB)

    DAVIS, S.J.

    2000-04-06

    This procedure provides a safe, uniform method for the performance of the ultrasonic weld inspection of the Cesium capsule overpacks. The inspection system will detect cracks, lack of fusion, and lack of penetration. This computer controlled automated system will perform the examination once the capsule overpack has been placed in the pool cell. Examination of the capsule overpacks will be in accordance with drawing H-283014, REV. 0 ,and a certified NDE examiner will perform the test procedure, provide analysis, and test documentation.

  3. Sensor Conditioning for Ultrasonic Remote Sensing Immersion

    OpenAIRE

    Breton, Sylvie; Benbouzid, Mohamed

    2013-01-01

    International audience; Ultrasonic detection has many applications in military, medical, marine biology, and physics domains. This paper presents then an emitting signal design for several immersion applications such as liquid level measurement, wall detection for submarine robots, and fish species behavior study. The designed and realized circuits are very simple, of flexible use, and cost-effective. Sensor sealing problems are also discussed in this paper.

  4. Updated Results of Ultrasonic Transducer Irradiation Test

    Energy Technology Data Exchange (ETDEWEB)

    Daw, Joshua; Palmer, Joe [Idaho National Laboratory, P.O. Box 1625, MS 4112, Idaho Falls, ID, 38415-3840 (United States); Ramuhalli, Pradeep; Keller, Paul; Montgomery, Robert [Pacific Northwest National Laboratory, 902 Battelle Blvd. Richland, WA, 99354 (United States); Chien, Hual-Te [Argonne National Laboratory, 9700 S. Cass Avenue Argonne, IL, 60439 (United States); Tittmann, Bernhard; Reinhardt, Brian [Pennsylvania State University, 212 Earth and Engr. Sciences Building, University Park, PA, 16802 (United States); Kohse, Gordon [Massachusetts Institute of Technology, 77 Massachusetts Ave. Cambridge, MA 02139 (United States); Rempe, Joy [Rempe and Associates, LLC, 360 Stillwater, Idaho Falls, ID 83404 (United States); Villard, J.F. [Commissariat a l' energie atomique et aux energies alternatives, Centre d' etudes de Cadarache, 13108 Saint-Paul-lez-Durance (France)

    2015-07-01

    Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10{sup 21} n/cm{sup 2}. A multi-National Laboratory collaboration funded by the Nuclear Energy Enabling Technologies Advanced Sensors and Instrumentation (NEET-ASI) program also provided initial support for this effort. This irradiation, which started in February 2014, is an instrumented lead test and real-time transducer performance data are collected along with temperature and neutron and gamma flux data. The irradiation is ongoing and will continue to approximately mid-2015. To date, very encouraging results have been attained as several transducers continue to operate under irradiation. (authors)

  5. Finite Element Modeling for Ultrasonic Transducers (Preprint)

    Science.gov (United States)

    1998-02-27

    virtual prototyping of transducers . Fig. 18 shows a 3D model of a Tonpilz device for low frequency sensing in air. This classical design is usually used...coupled Tonpilz transducer . A thick, flexible matching layer is bonded to the face of the conical head-mass. 7. CONCLUSIONS This paper was intended as a...This is a preprint of a paper published in Proc. SPIE Int. Symp. Medical Imaging 1998, San Diego, Feb 21-27, 1998 Ultrasonic Transducer Engineering

  6. Accelerating degradation rate of pure iron by zinc ion implantation

    Science.gov (United States)

    Huang, Tao; Zheng, Yufeng; Han, Yong

    2016-01-01

    Pure iron has been considered as a promising candidate for biodegradable implant applications. However, a faster degradation rate of pure iron is needed to meet the clinical requirement. In this work, metal vapor vacuum arc technology was adopted to implant zinc ions into the surface of pure iron. Results showed that the implantation depth of zinc ions was about 60 nm. The degradation rate of pure iron was found to be accelerated after zinc ion implantation. The cytotoxicity tests revealed that the implanted zinc ions brought a slight increase on cytotoxicity of the tested cells. In terms of hemocompatibility, the hemolysis of zinc ion implanted pure iron was lower than 2%. However, zinc ions might induce more adhered and activated platelets on the surface of pure iron. Overall, zinc ion implantation can be a feasible way to accelerate the degradation rate of pure iron for biodegradable applications. PMID:27482462

  7. AgraPure Mississippi Biomass Project

    Energy Technology Data Exchange (ETDEWEB)

    Blackwell,D.A; Broadhead, L.W.; Harrell, W.J.

    2006-03-31

    The AgraPure Mississippi Biomass project was a congressionally directed project, initiated to study the utilization of Mississippi agricultural byproducts and waste products in the production of bio-energy and to determine the feasibility of commercialization of these agricultural byproducts and waste products as feedstocks in the production of energy. The final products from this project were two business plans; one for a Thermal plant, and one for a Biodiesel/Ethanol plant. Agricultural waste fired steam and electrical generating plants and biodiesel plants were deemed the best prospects for developing commercially viable industries. Additionally, oil extraction methods were studied, both traditional and two novel techniques, and incorporated into the development plans. Mississippi produced crop and animal waste biomasses were analyzed for use as raw materials for both industries. The relevant factors, availability, costs, transportation, storage, location, and energetic value criteria were considered. Since feedstock accounts for more than 70 percent of the total cost of producing biodiesel, any local advantages are considered extremely important in developing this particular industry. The same factors must be evaluated in assessing the prospects of commercial operation of a steam and electrical generation plant. Additionally, the access to the markets for electricity is more limited, regulated and tightly controlled than the liquid fuel markets. Domestically produced biofuels, both biodiesel and ethanol, are gaining more attention and popularity with the consuming public as prices rise and supplies of foreign crude become less secure. Biodiesel requires no major modifications to existing diesel engines or supply chain and offers significant environmental benefits. Currently the biodiesel industry requires Federal and State incentives to allow the industry to develop and become self-sustaining. Mississippi has available the necessary feedstocks and is

  8. Radiation damage of polymers in ultrasonic fields

    Energy Technology Data Exchange (ETDEWEB)

    Anbalagan, Poornnima

    2008-07-01

    Radiation damage has always been a topic of great interest in various fields of sciences. In this work, an attempt is made to probe into the effect of subthreshold ultrasonic waves on the radiation damage created by irradiation of deuterons in polymer samples wherein the polymer samples act as model systems. Two equal volumes of radiation damage were produced in a single polymer sample wherein a standing wave of ultrasound was introduced into one. Three polymers namely, Polycarbonate, Polymethylmethacrylate and Polyvinyl chloride were used in this work. Four independent techniques were used to analyze the irradiated samples and visualize the radiation damage. Interferometric measurements give a measure of the refractive index modulation in the irradiated sample. Polymers, being transparent, do not absorb in the visible region of the electromagnetic spectrum. UV-Vis absorption spectroscopy shows absorption peaks in the visible region in irradiated polymer samples. Ion irradiation causes coloration of polymers. The light microscope is used to measure the absorption of white light by the irradiated polymers. Positron annihilation spectroscopy is used to obtain a measure of the open volume created by irradiation in polymers. A comparison between the irradiated region and the region exposed to ultrasonic waves simultaneously with irradiation in a polymer sample shows the polymer specific influence of the ultrasonic standing wave. (orig.)

  9. Ultrasonic Study of Dislocation Dynamics in Lithium -

    Science.gov (United States)

    Han, Myeong-Deok

    1987-09-01

    Experimental studies of dislocation dynamics in LiF single crystals, using ultrasonic techniques combined with dynamic loading, were performed to investigate the time evolution of the plastic deformation process under a short stress pulse at room temperature, and the temperature dependence of the dislocation damping mechanism in the temperature range 25 - 300(DEGREES)K. From the former, the time dependence of the ultrasonic attenuation was understood as resulting from dislocation multiplication followed by the evolution of mobile dislocations to immobile ones under large stress. From the latter, the temperature dependence of the ultrasonic attenuation was interpreted as due to the motion of the dislocation loops overcoming the periodic Peierls potential barrier in a manner analogous to the motion of a thermalized sine-Gordon chain under a small stress. The Peierls stress obtained from the experimental results by application of Seeger's relaxation model with exponential dislocation length distribution was 4.26MPa, which is consistent with the lowest stress for the linear relation between the dislocation velocity and stress observed by Flinn and Tinder.

  10. Comparison of piezoresistive and capacitive ultrasonic transducers

    Science.gov (United States)

    Neumann, John J.; Greve, David W.; Oppenheim, Irving J.

    2004-07-01

    MEMS ultrasonic transducers for flaw detection have heretofore been built as capacitive diaphragm-type devices. A diaphragm forms a moveable electrode, placed at a short gap from a stationary electrode, and diaphragm movement has been detected by capacitance change. Although several research teams have successfully demonstrated that technology, the detection of capacitance change is adversely affected by stray and parasitic capacitances, limiting the sensitivity of such transducers and typically requiring relatively large diaphragm areas. We describe the design and fabrication of what to our knowledge is the first CMOS-MEMS ultrasonic phased array transducer using piezoresistive strain sensing. Piezoresistors have been patterned within the diaphragms, and diaphragm movement creates bending strain which is detected by a bridge circuit, for which conductor losses will be less significant. The prospective advantage of such piezoresistive transducers is that sufficient sensitivity may be achieved with very small diaphragms. We compare transducer response under fluid-coupled ultrasonic excitation and report the experimental gauge factor for the piezoresistors. We also discuss the phased array performance of the transducer in sensing the direction of an incoming wave.

  11. Ultrasonic Flaw Imaging via Multipath Exploitation

    Directory of Open Access Journals (Sweden)

    Yimin D. Zhang

    2012-01-01

    Full Text Available We consider ultrasonic imaging for the visualization of flaws in a material. Ultrasonic imaging is a powerful nondestructive testing (NDT tool which assesses material conditions via the detection, localization, and classification of flaws inside a structure. We utilize reflections of ultrasonic signals which occur when encountering different media and interior boundaries. These reflections can be cast as direct paths to the target corresponding to the virtual sensors appearing on the top and bottom side of the target. Some of these virtual sensors constitute a virtual aperture, whereas in others, the aperture changes with the transmitter position. Exploitations of multipath extended virtual array apertures provide enhanced imaging capability beyond the limitation of traditional multisensor approaches. The waveforms observed at the physical as well as the virtual sensors yield additional measurements corresponding to different aspect angles, thus allowing proper multiview imaging of flaws. We derive the wideband point spread functions for dominant multipaths and show that fusion of physical and virtual sensor data improves the flaw perimeter detection and localization performance. The effectiveness of the proposed multipath exploitation approach is demonstrated using real data.

  12. Ultrasonic guided wave tomography for ice detection.

    Science.gov (United States)

    Zhao, Xiang; Rose, Joseph L

    2016-04-01

    Of great concern for many structures, particularly critical sections of rotary and fixed wing aircrafts, is the ability to detect ice either on grounded or in-flight vehicles. As a consequence, some work is reported here that could be useful for a variety of different industries where ice formation is an important problem. This paper presents experimental validations of a probability-based reconstruction algorithm (PRA) on ice detection of plate-like structures. The ice detection tests are performed for three different specimens: a single layer aluminum plate with a circular ice sensing array, a titanium plate with a sparse rectangular ice sensing array, and a carbon-fiber-reinforced titanium plate with an embedded ice sensing array mounted on a carbon fiber back plate. Cases from the simple to the more challenging exemplify that special modes can be used to differentiate ice from water, a sparse rectangular array could also be used for ice detection, and an ice sensing array could be further used to detect the ice on the sensor free side, a very useful application of ice sensing for aircraft wings, for example. Ice detection images for the respective cases are reconstructed to investigate the feasibility of ice sensing with ultrasonic guided wave tomography technology. The results show that the PRA based ultrasonic guided wave tomography method successfully detected and showed ice spots correctly for all three cases. This corroborates the fact that ultrasonic guided wave imaging technology could be a potential useful ice sensing tool in plate-like structures.

  13. Workflow to numerically reproduce laboratory ultrasonic datasets

    Institute of Scientific and Technical Information of China (English)

    A. Biryukov; N. Tisato; G. Grasselli

    2014-01-01

    The risks and uncertainties related to the storage of high-level radioactive waste (HLRW) can be reduced thanks to focused studies and investigations. HLRWs are going to be placed in deep geological re-positories, enveloped in an engineered bentonite barrier, whose physical conditions are subjected to change throughout the lifespan of the infrastructure. Seismic tomography can be employed to monitor its physical state and integrity. The design of the seismic monitoring system can be optimized via con-ducting and analyzing numerical simulations of wave propagation in representative repository geometry. However, the quality of the numerical results relies on their initial calibration. The main aim of this paper is to provide a workflow to calibrate numerical tools employing laboratory ultrasonic datasets. The finite difference code SOFI2D was employed to model ultrasonic waves propagating through a laboratory sample. Specifically, the input velocity model was calibrated to achieve a best match between experi-mental and numerical ultrasonic traces. Likely due to the imperfections of the contact surfaces, the resultant velocities of P- and S-wave propagation tend to be noticeably lower than those a priori assigned. Then, the calibrated model was employed to estimate the attenuation in a montmorillonite sample. The obtained low quality factors (Q) suggest that pronounced inelastic behavior of the clay has to be taken into account in geophysical modeling and analysis. Consequently, this contribution should be considered as a first step towards the creation of a numerical tool to evaluate wave propagation in nuclear waste repositories.

  14. A novel device for determining ultrasonic power

    Science.gov (United States)

    Zeqiri, B.; Shaw, A.; Gélat, P. N.; Bell, D.; Sutton, Y. C.

    2004-01-01

    A novel concept for an ultrasonic power meter is presented which utilises the pyro-electric effect of a thin membrane of the piezo-electric polymer, pvdf. One side of the membrane is in intimate contact with a polyurethane-based acoustical absorber. The attenuation coefficient of this material is very high, ensuring that the majority of the ultrasonic energy passing through the pvdf membrane is absorbed within a thin layer of the interface, resulting in a rapid increase in temperature. Through the pyro-electric effect, this temperature increase results in a voltage across the electrodes of the membrane. Under specific conditions, the generated voltage is proportional to the rate of temperature rise and, immediately after switch on of ultrasound, the rate of temperature rise is proportional to the delivered ultrasonic power. This paper describes details of the concept, and includes theoretical calculations of the expected behaviour. Proof-of-concept is demonstrated through careful studies of several low-megahertz NPL reference therapy-level transducers, covering an applied power range of 250 mW to 8 W. Results are encouraging, suggesting that this novel solid-state power meter concept holds considerable promise for a rapid, simple, relatively low cost, power measurement method, appropriate for use at the physiotherapist level.

  15. A Review of Ultrasonic Nano Manipulation Technology

    Institute of Scientific and Technical Information of China (English)

    Junhui Hu∗

    2016-01-01

    Nano manipulation technology has great potential applications in the assembly, measurement and fabrication of nano materials, actuating and high-sensitivity sensing of biological samples, manufacture of nano sensors, decontamination of air and water, etc. As an actuating technology which is far from being mature, the nano manipulation still faces lots of challenges in the device principles, design, scaling up, sample safety, etc. The ultrasonic nano manipulation, in which nanoscale objects are handled and actuated by controlled ultrasound, is an emerging technology to meet some of challenges in nano manipulations. The author’ s research team and other groups have proposed and realized a series of nano manipulation functions such as trapping, transfer, rotation and concentration since 2012, by controlled ultrasound. Compared with other nano manipulating techniques, the ultrasonic method has the merits such as very low temperature rise at the manipulation area, little selectivity to the material properties of manipulated samples, capability of being implemented on the substrates without MENS or NEMS structure, etc. This paper reviews the progresses in principles, functions, structures and characteristics of the ultrasonic devices for nano manipulations.

  16. Piezoelectric paint sensor for ultrasonic NDE

    Science.gov (United States)

    Li, X.; Zhang, Y.

    2007-04-01

    This paper deals with a distributed acoustic emission sensing method, which is especially suitable for piezoelectric paint. Piezoelectric paint is a composite piezoelectric material that is comprised of tiny piezoelectric particles randomly dispersed within a polymer matrix phase. An overview of the distributed acoustic emission sensing method for defect monitoring is given in this paper. The use of piezoelectric materials for ultrasonic signal measurements is next discussed along with a series of ultrasonic tests performed to verify the ultrasonic sensing capability of piezoelectric paint. To examine the mechanism of the distributed acoustic emission sensing method for crack initiation detection, the results of a finite element simulation based study is presented in this paper. The finite element model used in the parametric study is calibrated with experimental data. The effect of sensor numbers included in the array has been studied using both simulation and experimental data. Based on the preliminary results of this study, piezoelectric paint sensor appears to hold a potential for use in on-line monitoring of cracks such as those caused by fatigue in metal structures although more work is still needed before successful practical application can be made.

  17. Sandwich Panels Evaluated With Ultrasonic Spectroscopy

    Science.gov (United States)

    Cosgriff, Laura M.

    2004-01-01

    Enhanced, lightweight material systems, such as 17-4PH stainless steel sandwich panels are being developed for use as fan blades and fan containment systems for next-generation engines. The bond strength between the core and face sheets is critical in maintaining the structural integrity of the sandwich structure. To improve the inspection and production of these systems, researchers at the NASA Glenn Research Center are using nondestructive evaluation (NDE) techniques, such as ultrasonic spectroscopy, to evaluate the brazing quality between the face plates and the metallic foam core. The capabilities and limitations of a swept-frequency approach to ultrasonic spectroscopy were evaluated with respect to these sandwich structures. This report discusses results from three regions of a sandwich panel representing different levels of brazing quality between the outer face plates and a metallic foam core. Each region was investigated with ultrasonic spectroscopy. Then, on the basis of the NDE results, three shear specimens sectioned from the sandwich panel to contain each of these regions were mechanically tested.

  18. Ultrasonic drug delivery--a general review.

    Science.gov (United States)

    Pitt, William G; Husseini, Ghaleb A; Staples, Bryant J

    2004-11-01

    Ultrasound has an ever-increasing role in the delivery of therapeutic agents, including genetic material, protein and chemotherapeutic agents. Cavitating gas bodies, such as microbubbles, are the mediators through which the energy of relatively non-interactive pressure waves is concentrated to produce forces that permeabilise cell membranes and disrupt the vesicles that carry drugs. Thus, the presence of microbubbles enormously enhances ultrasonic delivery of genetic material, proteins and smaller chemical agents. Numerous reports show that the most efficient delivery of genetic material occurs in the presence of cavitating microbubbles. Attaching the DNA directly to the microbubbles, or to gas-containing liposomes, enhances gene uptake even further. Ultrasonic-enhanced gene delivery has been studied in various tissues, including cardiac, vascular, skeletal muscle, tumour and even fetal tissue. Ultrasonic-assisted delivery of proteins has found most application in transdermal transport of insulin. Cavitation events reversibly disrupt the structure of the stratus corneum to allow transport of these large molecules. Other hormones and small proteins could also be delivered transdermally. Small chemotherapeutic molecules are delivered in research settings from micelles and liposomes exposed to ultrasound. Cavitation appears to play two roles: it disrupts the structure of the carrier vesicle and releases the drug; and makes cell membranes and capillaries more permeable to drugs. There remains a need to better understand the physics of cavitation of microbubbles and the impact that such cavitation has on cells and drug-carrying vesicles.

  19. Constructing ultrasonic images of soft spherical scatterers

    Science.gov (United States)

    Annenkova, E. A.; Tsysar', S. A.; Sapozhnikov, O. A.

    2016-03-01

    The paper considers specific features of ultrasonic visualization of gas bubbles in a liquid or a medium of like soft biological tissue type under conditions when the size of scatterers is comparable to the acoustic wavelength. It was proposed to use styrofoam specimens as the experimental model of stationary gas bubbles. Patterns of ultrasound scattering by a styrofoam sphere in water were obtained experimentally. It was shown that the measurement results agree well with the prediction of the classical theoretical model of scattering of a plane wave by a perfectly soft sphere. Several experiments were performed illustrating the specific features of visualizing millimeter-sized bubbles. A Terason commercial ultrasonic scanner was used; gelatin specimens with embedded styrofoam spheres served as the objects of study. The simulation and experimental results showed that when bubbles with diameters of visualized, it is impossible to measure the diameter of scatterers because bubbles of different diameters are imaged as bright spots of identical diameter, which is equal to the scanner resolution. To eliminate this difficulty, it is recommended to use the results of theoretical simulation performed in this study, which revealed a monotonic increase in the backscattered signal intensity with an increase in bubble radius. An ultrasonic visualization mode is proposed in which the brightness of scattered signals is used to differentiate between bubbles of different size.

  20. Nondestructive Ultrasonic Inspection of Friction Stir Welds

    Science.gov (United States)

    Tabatabaeipour, M.; Hettler, J.; Delrue, S.; Van Den Abeele, K.

    Friction Stir Welding (FSW) is a relatively new solid-state welding procedure developed at The Welding Institute (TWI-UK) and the technique is widely employed for welding aluminum alloys in various applications. In order to examine the quality of the welds and to detect a variety of welding flaws such as wormholes and root-flaws, it is required to develop a methodical inspection technique that can be used for the identification and localization of such defects. The most prevalent and risky defect in this type of welding is the barely visible root flaw with a length varying from 100-700 μm. Due to the extreme characteristics of the flaw, off-the-shelf ultrasonic weld inspection methods are not always able to readily detect this type of minute defect feature. Here, we propose a novel approach to characterize root flaws using an oblique incident ultrasonic C-scan backscattering analysis. The implementation consists of an immersion ultrasonic testing method in pulse echo (i.e. backscatter) mode with a 3.5 MHz transducer, and makes use of an empirical procedure to engender of a shear wave dominated excitation at the root surface, and to properly gate the received signal for root flaw examination. By scanning the surface above the welded component, a C-scan image displaying the backscatter response from the root surface of the nugget zone can be obtained which allows a simple interpretation of the root flaw status of the weld.